Reliability residual-life prediction method for thermal aging based on performance degradation

International Nuclear Information System (INIS)

Ren Shuhong; Xue Fei; Yu Weiwei; Ti Wenxin; Liu Xiaotian

2013-01-01

The paper makes the study of the nuclear power plant main pipeline. The residual-life of the main pipeline that failed due to thermal aging has been studied by the use of performance degradation theory and Bayesian updating methods. Firstly, the thermal aging impact property degradation process of the main pipeline austenitic stainless steel has been analyzed by the accelerated thermal aging test data. Then, the thermal aging residual-life prediction model based on the impact property degradation data is built by Bayesian updating methods. Finally, these models are applied in practical situations. It is shown that the proposed methods are feasible and the prediction accuracy meets the needs of the project. Also, it provides a foundation for the scientific management of aging management of the main pipeline. (authors)

Pathway and rate-limiting step of glyphosate degradation by Aspergillus oryzae A-F02.

Science.gov (United States)

Fu, Gui-Ming; Chen, Yan; Li, Ru-Yi; Yuan, Xiao-Qiang; Liu, Cheng-Mei; Li, Bin; Wan, Yin

2017-09-14

Aspergillus oryzae A-F02, a glyphosate-degrading fungus, was isolated from an aeration tank in a pesticide factory. The pathway and rate-limiting step of glyphosate (GP) degradation were investigated through metabolite analysis. GP, aminomethylphosphonic acid (AMPA), and methylamine were detected in the fermentation liquid of A. oryzae A-F02, whereas sarcosine and glycine were not. The pathway of GP degradation in A. oryzae A-F02 was revealed: GP was first degraded into AMPA, which was then degraded into methylamine. Finally, methylamine was further degraded into other products. Investigating the effects of the exogenous addition of substrates and metabolites showed that the degradation of GP to AMPA is the rate-limiting step of GP degradation by A. oryzae A-F02. In addition, the accumulation of AMPA and methylamine did not cause feedback inhibition in GP degradation. Results showed that degrading GP to AMPA was a crucial step in the degradation of GP, which determines the degradation rate of GP by A. oryzae A-F02.

Modeling rates of DOC degradation using DOM composition and hydroclimatic variables

Science.gov (United States)

Moody, C. S.; Worrall, F.

2017-05-01

The fluvial fluxes of dissolved organic carbon (DOC) from peatlands form an important part of that ecosystem's carbon cycle, contributing approximately 35% of the overall peatland carbon budget. The in-stream processes acting on the DOC, such as photodegradation and biodegradation, can lead to DOC loss and thus contribute CO2 to the atmosphere. The aim of this study was to understand what controls the rates of DOC degradation. Water samples from a headwater, peat-covered catchment, were collected over a 23 month period and analyzed for the DOC degradation rate and dissolved organic matter (DOM) composition in the context of hydroclimatic monitoring. Measures of DOM composition included 13C solid-state nuclear magnetic resonance spectroscopy, bomb calorimetry, and elemental analysis. Regression analysis showed that there was a significant role for the composition of the DOM in controlling degradation with degradation rates significantly increasing with the proportion of aldehyde and carboxylic acid functional groups but decreasing with the proportion of N-alkyl functional groups. The highest rates of DOC degradation occurred when aldehyde functionality was at its greatest and this occurred on the recession limb of storm hydrographs. Including this knowledge into models of fluvial carbon fate for an 818 km2 catchment gave an annual average DOC removal rate of 67% and 50% for total organic carbon, slightly lower than previously predicted. The compositional controls suggest that DOM is primarily being used as a ready energy source to the aquatic ecosystem rather than as a nutrient source.

Degradation rate of acetylcholine receptors inserted into denervated vertebrate neuromuscular junctions

International Nuclear Information System (INIS)

Shyng, S.L.; Salpeter, M.M.

1989-01-01

Many studies exist on the effect of denervation on the degradation of acetylcholine receptors (AChRs) at the vertebrate neuromuscular junction (nmj). These studies have described the behavior of either the total population of junctional receptors at different times after denervation, or of the receptors present at the time of denervation. No experimental studies yet exist on the degradation rate of the receptors newly inserted into denervated junctions. In the previous studies, the original receptors of mouse sternomastoid muscles were found to retain the slow degradation (t 1/2) of approximately 8-10 d of innervated junctional receptors for up to 10 d after denervation before accelerating to a t 1/2 of approximately 3 d. The total junctional receptors, on the other hand, showed a progressive increase in degradation rate from a t 1/2 of 8-10 d to a t 1/2 of 1 d. To reconcile these earlier observations, the present study examines the degradation of new receptors inserted into the nmj after denervation. To avoid possible contamination of the data with postdenervation extrajunctional receptors, we used transmission electron microscope autoradiography to study only receptors located at the postjunctional fold of the nmj. We established that the new receptors inserted into denervated junctions have a t 1/2 of approximately 1 d, considerably faster than that of the original receptors and equivalent to that of postdenervation extrajunctional receptors. Both original and new receptors are interspersed at the top of the junctional folds. Thus, until all the original receptors are degraded, the postjunctional membrane contains two populations of AChRs that maintain a total steady-state site density but degrade at different rates

Assessment of chloroethene degradation rates based on ratios of daughter/parent compounds in groundwater plumes

Science.gov (United States)

Höhener, Patrick

2014-05-01

Chlorinated solvent spills at industrial and urban sites create groundwater plumes where tetrachloro- and trichloroethene may degrade to their daughter compounds, dichloroethenes, vinyl chloride and ethane. The assessment of degradation and natural attenuation at such sites may be based on the analysis and inverse modelling of concentration data, on the calculation of mass fluxes in transsects, and/or on the analysis of stable isotope ratios in the ethenes. Relatively few work has investigated the possibility of using ratio of concentrations for gaining information on degradation rates. The use of ratios bears the advantage that dilution of a single sample with contaminant-free water does not matter. It will be shown that molar ratios of daughter to parent compounds measured along a plume streamline are a rapid and robust mean of determining whether degradation rates increase or decrease along the degradation chain, and allow furthermore a quantitation of the relative magnitude of degradation rates compared to the rate of the parent compound. Furthermore, ratios of concentration will become constant in zones where degradation is absent, and this allows to sketching the extension of actively degrading zones. The assessment is possible for pure sources and also for mixed sources. A quantification method is proposed in order to estimate first-order degradation rates in zones of constant degradation activity. This quantification method includes corrections that are needed due to longitudinal and transversal dispersivity. The method was tested on a number of real field sites from literature. At the majority of these sites, the first-order degradation rates were decreasing along the degradation chain from tetrachloroethene to vinyl chloride, meaning that the latter was often reaching important concentrations. This is bad news for site owners due to the increased toxicity of vinyl chloride compared to its parent compounds.

Lifetime Evaluation of Grid-Connected PV Inverters Considering Panel Degradation Rates and Installation Sites

DEFF Research Database (Denmark)

Sangwongwanich, Ariya; Yang, Yongheng; Sera, Dezso

2018-01-01

Lifetime of PV inverters is affected by the installation sites related to different solar irradiance and ambient temperature profiles (also referred to as mission profiles). In fact, the installation site also affects the degradation rate of the PV panels, and thus long-term energy production...... and reliability. Prior-art lifetime analysis in PV inverters has not yet investigated the impact of PV panel degradations. This paper thus evaluates the lifetime of PV inverters considering panel degradation rates and mission profiles. Evaluations have been carried out on PV systems installed in Denmark...... and Arizona. The results reveal that the PV panel degradation rate has a considerable impact on the PV inverter lifetime, especially in the hot climate (e.g., Arizona), where the panel degrades at a faster rate. In that case, the PV inverter lifetime prediction can be deviated by 54%, if the impact of PV...

Kinetics analysis for development of a rate constant estimation model for ultrasonic degradation reaction of methylene blue.

Science.gov (United States)

Kobayashi, Daisuke; Honma, Chiemi; Matsumoto, Hideyuki; Takahashi, Tomoki; Kuroda, Chiaki; Otake, Katsuto; Shono, Atsushi

2014-07-01

Ultrasound has been used as an advanced oxidation method for wastewater treatment. Sonochemical degradation of organic compounds in aqueous solution occurs by pyrolysis and/or reaction with hydroxyl radicals. Moreover, kinetics of sonochemical degradation has been proposed. However, the effect of ultrasonic frequency on degradation rate has not been investigated. In our previous study, a simple model for estimating the apparent degradation rate of methylene blue was proposed. In this study, sonochemical degradation of methylene blue was performed at various frequencies. Apparent degradation rate constant was evaluated assuming that sonochemical degradation of methylene blue was a first-order reaction. Specifically, we focused on effects of ultrasonic frequency and power on rate constant, and the applicability of our proposed model was demonstrated. Using this approach, maximum sonochemical degradation rate was observed at 490 kHz, which agrees with a previous investigation into the effect of frequency on the sonochemical efficiency value evaluated by KI oxidation dosimetry. Degradation rate increased with ultrasonic power at every frequency. It was also observed that threshold power must be reached for the degradation reaction to progress. The initial methylene blue concentration and the apparent degradation rate constant have a relation of an inverse proportion. Our proposed model for estimating the apparent degradation rate constant using ultrasonic power and sonochemical efficiency value can apply to this study which extended the frequency and initial concentration range. Copyright © 2013 Elsevier B.V. All rights reserved.

Radiation-thermal degradation of PE and PVC: Mechanism of synergism and dose rate effects

Science.gov (United States)

Clough, Roger L.; Gillen, Kenneth T.

Polyethylene insulation and polyvinyl chloride jacketing materials that had been in use in a nuclear application were recently found to be substantially deteriorated. The damage had occurred under conditions where both the total estimated dose (about 2.5 Mrad) and the operating temperatures (about 43°C average) seemed relatively moderate. These results prompted us to initiate a program to study polyvinyl chloride and polyethylene degradation under conditions of combined γ-radiation and elevated temperature environments. A number of interesting aging effects were observed, including 1) a striking synergism between radiation and temperature and 2) strong dose-rate dependent effects which occur over a wide range of dose rates. The aging effects are explained in terms of a chain branching degradation mechanism involving thermally induced breakdown of peroxides which are formed in reactions initiated by the radiation. Evidence for this mechanism is derived from infrared spectra, from sequential radiation-elevated temperature experiments including experiments under inert atmosphere, from activation energy estimates and from a new technique involving treatment of intact samples with PH 3 for chemical reduction of peroxides. The results of our studies raise significant doubts about the utility of earlier compilations which purportedly serve as radiation life expectancy guides by indicating "tolerable radiation doses" for a variety of polymers.

The Effect of High-Pressure Arc Discharge Plasma on the Degradation of Chlorpyrifos

International Nuclear Information System (INIS)

Yin Meiqiang; Ma Tengcai; Zhang Jialiang; Huang Mingjing; Ma Buzhou

2006-01-01

A study is conducted to determine the effect of a kind of high-pressure arc discharge plasma on the degradation rate and kinetic equations of chlorpyrifos in different solvents with the treated times and concentrations as variables. The degradation rate was sorted in different solvents as water, methanol, acetone and then acetoacetate. The tendencies of the degradation rates with treated time in water and methanol were optimally fitted with first-order kinetics equations while those in acetone and acetoacetate were fitted with zeroth-order kinetics equations. The difference was attributed to the stronger polarity of water and methanol. The weak correlation of the degradation rates with time was mainly because the high-temperature of the arc discharge tube and the chemically-active species generated by the discharge. The degradation half-life was extended with increase of chlorpyrifos concentration. A degradation half-life less than 3 min was achieved for chlorpyrifos in water and methanol when the initial concentration was less than 300 μg/ml

Use of Pyranometers to Estimate PV Module Degradation Rates in the Field: Preprint

Energy Technology Data Exchange (ETDEWEB)

Vignola, Frank; Peterson, Josh; Kessler, Rich; Mavromatakis, Fotis; Dooraghi, Mike; Sengupta, Manajit

2016-08-01

This paper describes a methodology that uses relative measurements to estimate the degradation rates of PV modules in the field. The importance of calibration and cleaning is illustrated. The number of years of field measurements needed to measure degradation rates with data from the field is cut in half using relative comparisons.

Degradation of isobutanal at high loading rates in a compost biofilter.

Science.gov (United States)

Sercu, Bram; Demeestere, Kristof; Baillieul, Hans; Van Langenhove, Herman; Verstraete, Willy

2005-08-01

Biofiltration has been increasingly used for cleaning waste gases, mostly containing low concentrations of odorous compounds. To expand the application area of this technology, the biofiltration of higher pollutant loading rates has to be investigated. This article focuses on the biodegradation of isobutanal (IBAL) in a compost biofilter (BF) at mass loading rates between 211 and 4123 g/m3/day (30-590 ppm(v)). At mass loading rates up to 785 g/m3/day, near 100% removal efficiencies could be obtained. However, after increasing the loading rate to 1500-1900 g/m3/ day, the degradation efficiency decreased to 62-98%. In addition, a pH decrease and production of isobutanol (IBOL) and isobutyric acid (IBAC) were observed. This is the first report showing that an aldehyde can act as electron donor as well as acceptor in a BF. To study the effects of pH, compost moisture content, and electron acceptor availability on the biofiltration of IBAL, IBOL, and IBAC, additional batch and continuous experiments were performed. A pH of 5.2 reduced the IBAL degradation rate and inhibited the IBOL degradation, although adaptation of the microorganisms to low pH was observed in the BFs. IBAC was not degraded in the batch experiments. High moisture content (51%) initially had no effect on the IBOL production, although it negatively affected the IBAL elimination increasingly during a 21-day time-course experiment. In batch experiments, the reduction of IBAL to IBOL did not decrease when the amount of available electron acceptors (oxygen or nitrate) was increased. The IBAL removal efficiency at higher loading rates was limited by a combination of nutrient limitation, pH decrease, and dehydration, and the importance of each limiting factor depended on the influent concentration.

Single molecule approaches for quantifying transcription and degradation rates in intact mammalian tissues.

Science.gov (United States)

Bahar Halpern, Keren; Itzkovitz, Shalev

2016-04-01

A key challenge in mammalian biology is to understand how rates of transcription and mRNA degradation jointly shape cellular gene expression. Powerful techniques have been developed for measuring these rates either genome-wide or at the single-molecule level, however these techniques are not applicable to assessment of cells within their native tissue microenvironment. Here we describe a technique based on single molecule Fluorescence in-situ Hybridization (smFISH) to measure transcription and degradation rates in intact mammalian tissues. The technique is based on dual-color libraries targeting the introns and exons of the genes of interest, enabling visualization and quantification of both nascent and mature mRNA. We present a software, TransQuant, that facilitates quantifying these rates from smFISH images. Our approach enables assessment of both transcription and degradation rates of any gene of interest while controlling for the inherent heterogeneity of intact tissues. Copyright © 2015 Elsevier Inc. All rights reserved.

Biologically Safe Poly(l-lactic acid) Blends with Tunable Degradation Rate: Microstructure, Degradation Mechanism, and Mechanical Properties.

Science.gov (United States)

Oyama, Hideko T; Tanishima, Daisuke; Ogawa, Ryohei

2017-04-10

Although poly(l-lactic acid) (PLLA) is reputed to be biodegradable in the human body, its hydrophobic nature lets it persist for ca. 5.5 years. This study demonstrates that biologically safe lactide copolymers, poly(aspartic acid-co-l-lactide) (PAL) and poly(malic acid-co-l-lactide) (PML), dispersed in the PLLA function as detonators (triggers) for its hydrolytic degradation under physiological conditions. The copolymers significantly enhance hydrolysis, and consequently, the degradation rate of PLLA becomes easily tunable by controlling the amounts of PAL and PML. The present study elucidates the effects of uniaxial drawing on the structural development, mechanical properties, and hydrolytic degradation under physiological conditions of PLLA blend films. At initial degradation stages, the mass loss was not affected by uniaxial drawing; however, at late degradation stages, less developed crystals as well as amorphous chains were degradable at low draw ratio (DR), whereas not only highly developed crystals but also the oriented amorphous chains became insensitive to hydrolysis at high DR. Our work provides important molecular level results that demonstrate that biodegradable materials can have superb mechanical properties and also disappear in a required time under physiological conditions.

Calculating the Degradation Rate of Individual Proteins Using Xenopus Extract Systems.

Science.gov (United States)

McDowell, Gary S; Philpott, Anna

2018-05-16

The Xenopus extract system has been used extensively as a simple, quick, and robust method for assessing the stability of proteins against proteasomal degradation. In this protocol, methods are provided for assessing the half-life of in vitro translated radiolabeled proteins using Xenopus egg or embryo extracts. © 2019 Cold Spring Harbor Laboratory Press.

Influence of the dose rate in the PVDF degradation processes

Energy Technology Data Exchange (ETDEWEB)

Batista, Adriana S.M.; Pereira, Claubia, E-mail: adriananuclear@yahoo.com.br, E-mail: claubia@nuclear.ufmg.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil); Gual, Maritza R., E-mail: maritzargual@gmail.com [Instituto Superior de Tecnologias y Ciencias Aplicadas (InsTEC), Departamento de Ingenieria Nuclear, La Habana (Cuba); Faria, Luiz O., E-mail: farialo@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2015-07-01

Modification in polymeric structure of plastic material can be brought either by conventional chemical means or by exposure to ionization radiation from gamma radioactive sources or highly accelerated electrons. The prominent drawbacks of chemical cross-linking typically involve the generation by products such as peroxide degradation. Radiation cross-linking technologies include: application in cable and wire, application in rubber tyres, radiation vulcanization of rubber latex, polymer recycling, hydrogels etc. The degradation of PVDF polymer exposed to gamma irradiation in oxygen atmosphere in high dose rate has been studied and compared to obtained under smaller dose rates. The samples were irradiated with a Co-60 source at constant dose rate (12 kGy/h and 2,592 kGy/h), with doses ranging from 100 kGy to 3,000 kGy. Different dose rate determine the prevalence of the processes being evaluated in this work by thermal measurements and infrared spectroscopy. It is shown that the degradation processes involve chain scissions and crosslink formation. The formation of oxidation products was shown at the surface of the irradiated film. The FTIR data revealed absorption bands at 1730 and 1853 cm{sup -1} which were attributed to the stretch of C=O bonds, at 1715 and 1754 cm{sup -1} which were attributed to the C=C stretching and at 3518, 3585 and 3673 cm{sup -1} which were associated with NH stretch of NH{sub 2} and OH. Thermogravimetric studies reveal that the irradiation induced the increasing residues and decrease of the temperature of the decomposition start. (author)

Influence of the dose rate in the PVDF degradation processes

International Nuclear Information System (INIS)

Batista, Adriana S.M.; Pereira, Claubia; Gual, Maritza R.; Faria, Luiz O.

2015-01-01

Modification in polymeric structure of plastic material can be brought either by conventional chemical means or by exposure to ionization radiation from gamma radioactive sources or highly accelerated electrons. The prominent drawbacks of chemical cross-linking typically involve the generation by products such as peroxide degradation. Radiation cross-linking technologies include: application in cable and wire, application in rubber tyres, radiation vulcanization of rubber latex, polymer recycling, hydrogels etc. The degradation of PVDF polymer exposed to gamma irradiation in oxygen atmosphere in high dose rate has been studied and compared to obtained under smaller dose rates. The samples were irradiated with a Co-60 source at constant dose rate (12 kGy/h and 2,592 kGy/h), with doses ranging from 100 kGy to 3,000 kGy. Different dose rate determine the prevalence of the processes being evaluated in this work by thermal measurements and infrared spectroscopy. It is shown that the degradation processes involve chain scissions and crosslink formation. The formation of oxidation products was shown at the surface of the irradiated film. The FTIR data revealed absorption bands at 1730 and 1853 cm -1 which were attributed to the stretch of C=O bonds, at 1715 and 1754 cm -1 which were attributed to the C=C stretching and at 3518, 3585 and 3673 cm -1 which were associated with NH stretch of NH 2 and OH. Thermogravimetric studies reveal that the irradiation induced the increasing residues and decrease of the temperature of the decomposition start. (author)

Experimental degradation of polymer shopping bags (standard and degradable plastic, and biodegradable) in the gastrointestinal fluids of sea turtles.

Science.gov (United States)

Müller, Christin; Townsend, Kathy; Matschullat, Jörg

2012-02-01

The persistence of marine debris such as discarded polymer bags has become globally an increasing hazard to marine life. To date, over 177 marine species have been recorded to ingest man-made polymers that cause life-threatening complications such as gut impaction and perforation. This study set out to test the decay characteristics of three common types of shopping bag polymers in sea turtle gastrointestinal fluids (GIF): standard and degradable plastic, and biodegradable. Fluids were obtained from the stomachs, small intestines and large intestines of a freshly dead Green turtle (Chelonia mydas) and a Loggerhead turtle (Caretta caretta). Controls were carried out with salt and freshwater. The degradation rate was measured over 49 days, based on mass loss. Degradation rates of the standard and the degradable plastic bags after 49 days across all treatments and controls were negligible. The biodegradable bags showed mass losses between 3 and 9%. This was a much slower rate than reported by the manufacturers in an industrial composting situation (100% in 49 days). The GIF of the herbivorous Green turtle showed an increased capacity to break down the biodegradable polymer relative to the carnivorous Loggerhead, but at a much lower rate than digestion of natural vegetative matter. While the breakdown rate of biodegradable polymers in the intestinal fluids of sea turtles is greater than standard and degradable plastics, it is proposed that this is not rapid enough to prevent morbidity. Further study is recommended to investigate the speed at which biodegradable polymers decompose outside of industrial composting situations, and their durability in marine and freshwater systems. Copyright © 2011 Elsevier B.V. All rights reserved.

Degradation rates of phorbol esters in Jatropha curcas L. oil and pressed seeds under different storage conditions.

Science.gov (United States)

Phasukarratchai, Naphatsarnan; Damrongsiri, Seelawut; Tongcumpou, Chantra

2017-03-01

Phorbol esters (PEs), found in Jatropha curcas crude oil (JCO) and J. curcas pressed seeds (JPS), are known as bioactive compounds in agricultural and pharmaceutical applications. The degradation rates of PEs in JCO and JPS under various conditions is important for the utilisation of PEs. Thus the objective of this study was to determine the PE degradation rates in JCO and JPS under different storage conditions. PE degradation rates were found to be first-order reactions. The slowest degradation rate was at 0.9 × 10 -3 d -1 for both JCO and JPS unexposed to light at 4 °C. Light intensity (1097 lx and 4690 lx, representing diffused sunlight and fluorescent lighting, respectively) and temperature (25 to 35 °C) were the significant degradation factors. Light exposure led to 280% to 380% higher degradation rates in JCO than in JPS due to light penetration through the transparent oil. Dried and sterilised JPS showed an 80% to 90% lower PE degradation rate than untreated JPS under all storage conditions since biodegradation was assembly limited. The PEs were unstable under the studied conditions, especially when exposed to light and room temperature. To protect against PE degradation, a material should be stored in a light-protected container and below 4 °C. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Degradation of tributyltin in San Diego Bay, California, waters

International Nuclear Information System (INIS)

Seligman, P.F.; Valkirs, A.O.; Lee, R.F.

1986-01-01

Several experiments were carried out to determine the degradation rate of tributyltin (TBT) in microcosms containing harbor water. Unlabeled or 14 C-labeled tributyltin was added to water samples collected from two stations in San Diego Bay, CA. Degradation rates were determined by calculating the rate of loss of the added parent TBT compound. Calculated half-lives in water collected from a yacht harbor (ambient concentration was 0.5 μg of TBT/L) were 6 and 7 days for light and dark treatments, respectively. Half-lives from a clean-water site ( 14 CO 2 , proceeded slowly with a half-life of 50-75 days. Tributyltin at high concentrations (744 μg/L) was not degraded in sunlight, indicating that photolysis was not taking place and that biological degradation was the primary degradative process for TBT at low ambient concentrations

Hydrolysis of VX on concrete: rate of degradation by direct surface interrogation using an ion trap secondary ion mass spectrometer.

Science.gov (United States)

Groenewold, Gary S; Williams, John M; Appelhans, Anthony D; Gresham, Garold L; Olson, John E; Jeffery, Mark T; Rowland, Brad

2002-11-15

The nerve agent VX (O-ethyl S-2-diisopropylaminoethyl methylphosphonothiolate) is lethal at very low levels of exposure, which can occur by dermal contact with contaminated surfaces. Hence, behavior of VX in contact with common urban or industrial surfaces is a subject of acute interest. In the present study, VX was found to undergo complete degradation when in contact with concrete surfaces. The degradation was directly interrogated at submonolayer concentrations by periodically performing secondary ion mass spectrometry (SIMS) analyses after exposure of the concrete to VX. The abundance of the [VX + H]+ ion in the SIMS spectra was observed to decrease in an exponential fashion, consistent with first-order or pseudo-first-order behavior. This phenomenon enabled the rate constant to be determined at 0.005 min(-1) at 25 degrees C, which corresponds to a half-life of about 3 h on the concrete surface. The decrease in [VX + H]+ was accompanied by an increase in the abundance of the principal degradation product diisopropylaminoethanethiol (DESH), which arises by cleavage of the P-S bond. Degradation to form DESH is accompanied by the formation of ethyl methylphosphonic acid, which is observable only in the negative ion spectrum. A second degradation product was also implicated, which corresponded to a diisopropylvinylamine isomer (perhaps N,N-diisopropyl aziridinium) that arose via cleavage of the S-C bond. No evidence was observed for the formation of the toxic S-2-diisopropylaminoethyl methylphosphonothioic acid. The degradation rate constants were measured at four different temperatures (24-50 degrees C), which resulted in a linear Arrhenius relationship and an activation energy of 52 kJ mol(-1). This value agrees with previous values observed for VX hydrolysis in alkaline solutions, which suggests that the degradation of submonolayer VX is dominated by alkaline hydrolysis within the adventitious water film on the concrete surface.

Degradation of dimethyl disulphide in soil with or without biochar amendment.

Science.gov (United States)

Han, Dawei; Yan, Dongdong; Cao, Aocheng; Fang, Wensheng; Liu, Pengfei; Li, Yuan; Ouyang, Canbin; Wang, Qiuxia

2017-09-01

Dimethyl disulphide (DMDS) is a new and effective alternative to methyl bromide for soil fumigation. The effect of biochar on the fate of DMDS in soil is not fully understood. The objective of this study was to determine the degradation kinetics of DMDS in different soils and evaluate the effect of biochar amendment on DMDS degradation using incubation experiments. The degradation half-life of DMDS was between 1.05 and 6.66 days under non-sterile conditions, and 12.63 to 22.67 days under sterile conditions in five types of soil. Seven out of the eight tested biochar amendments (BC-2 to BC-8) delayed the degradation of DMDS in soil, increasing the half-life of DMDS in Fangshan soil from 1.05 to 1.16-5.87 days following amendment with 1% (w/w) biochar. The degradation rate of DMDS in Fangshan soil accelerated as the amendment rate of BC-1 increased, and decreased as the amendment rate of BC-7 increased. Biodegradation is an important degradation route for DMDS in soil, and DMDS degraded faster in alkaline soil. The effects of biochar amendments on DMDS degradation in soil are determined by complex multiple factors (such as surface area, pH and physicochemical composition), rather than by any single property of biochar. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Calculating in situ degradation rates of hydrocarbon compounds in deep waters of the Gulf of Mexico.

Science.gov (United States)

Thessen, Anne E; North, Elizabeth W

2017-09-15

Biodegradation is an important process for hydrocarbon weathering that influences its fate and transport, yet little is known about in situ biodegradation rates of specific hydrocarbon compounds in the deep ocean. Using data collected in the Gulf of Mexico below 700m during and after the Deepwater Horizon oil spill, we calculated first-order degradation rate constants for 49 hydrocarbons and inferred degradation rate constants for an additional 5 data-deficient hydrocarbons. Resulting calculated (not inferred) half-lives of the hydrocarbons ranged from 0.4 to 36.5days. The fastest degrading hydrocarbons were toluene (k=-1.716), methylcyclohexane (k=-1.538), benzene (k=-1.333), and C1-naphthalene (k=-1.305). The slowest degrading hydrocarbons were the large straight-chain alkanes, C-26 through C-33 (k=-0.0494 through k=-0.007). Ratios of C-18 to phytane supported the hypothesis that the primary means of degradation in the subsurface was microbial biodegradation. These degradation rate constants can be used to improve models describing the fate and transport of hydrocarbons in the event of an accidental deep ocean oil spill. Copyright © 2017 Elsevier Ltd. All rights reserved.

Zircaloy-oxidation and hydrogen-generation rates in degraded-core accident situations

International Nuclear Information System (INIS)

Chung, H.M.; Thomas, G.R.

1983-02-01

Oxidation of Zircaloy cladding is the primary source of hydrogen generated during a degraded-core accident. In this paper, reported Zircaloy oxidation rates, either measured at 1500 to 1850 0 C or extrapolated from the low-temperature data obtained at 0 C, are critically reviewed with respect to their applicability to a degraded-core accident situation in which the high-temperature fuel cladding is likely to be exposed to and oxidized in mixtures of hydrogen and depleted steam, rather than in an unlimited flux of pure steam. New results of Zircaloy oxidation measurements in various mixtures of hydrogen and steam are reported for >1500 0 C. The results show significantly smaller oxidation and, hence, hydrogen-generation rates in the mixture, compared with those obtained in pure steam. It is also shown that a significant fraction of hydrogen, generated as a result of Zircaloy oxidation, is dissolved in the cladding material itself, which prevents that portion of hydrogen from reaching the containment building space. Implications of these findings are discussed in relation to a more realistic method of quantifying the hydrogen source term for a degraded-core accident analysis

Enrofloxacin degradation in broiler chicken manure under various laboratory conditions.

Science.gov (United States)

Slana, Marko; Sollner-Dolenc, Marija

2016-03-01

The rate of degradation of enrofloxacin in broiler chicken manure has been characterized in the laboratory according to the CVMP guideline on determining the fate of veterinary medicinal products in manure. Degradation was followed in a flow-through system under aerobic and anaerobic conditions, in the dark and in the presence of light. The rate of degradation of enrofloxacin and the formation of its degradation products are dependent on laboratory conditions. A rapid degradation of enrofloxacin in the dark was noticed, where a shorter degradation half-life under aerobic (DT50 = 59.1 days), comparing to anaerobic conditions (DT50 = 88.9 days), was determined. The presence of light slowed down the enrofloxacin degradation half-life, which was significantly shorter under aerobic (DT50 = 115.0 days), comparing to anaerobic conditions (DT50 = 190.8 days). Desethylene-enrofoxacin was the only degradation product formed, its concentrations ranged from 2.5 to 14.9 %. The concentration of the degradation product was approximately 2.5-fold higher under aerobic conditions. Enrofloxacin degradation in sterile manure incubated under sterile conditions was marginal comparing to non-sterile conditions; after 120 days of incubation, approximately 80 % of enrofloxacin was still present in manure and only 1 % of desethylene-enrofloxacin was formed. The present work demonstrates that enrofloxacin degradation in chicken manure is relatively fast when incubated in the dark under aerobic conditions which is the recommended incubation system for chicken manure according to CVMP guideline.

Degradable and porous Fe-Mn-C alloy for biomaterials candidate

Science.gov (United States)

Pratesa, Yudha; Harjanto, Sri; Larasati, Almira; Suharno, Bambang; Ariati, Myrna

2018-02-01

Nowadays, degradable implants attract attention to be developed because it can improve the quality of life of patients. The degradable implant is expected to degrade easily in the body until the bone healing process already achieved. However, there is limited material that could be used as a degradable implant, polymer, magnesium, and iron. In the previous study, Fe-Mn-C alloys had succesfully produced austenitic phase. However, the weakness of the alloy is degradation rate of materials was considered below the expectation. This study aimed to produce porous Fe-Mn-C materials to improve degradation rate and reduce the density of alloy without losing it non-magnetic properties. Potassium carbonate (K2CO3) were chosen as filler material to produce foam structure by sintering and dissolution process. Multisteps sintering process under argon gas environment was performed to generate austenite phase. The product showed an increment of the degradation rate of the foamed Fe-Mn-C alloy compared with the solid Fe-Mn-C alloy without losing the Austenitic Structure

Status Report - Cane Fiberboard Properties and Degradation Rates for Storage of the 9975 Shipping Package in KAMS

International Nuclear Information System (INIS)

Daugherty, W. L.

2013-01-01

Thermal, mechanical and physical properties have been measured on cane fiberboard samples following accelerated aging for up to approximately 7 years. The aging environments have included elevated temperature > 250 deg F (the maximum allowed service temperature for fiberboard in 9975 packages) and elevated humidity. The results from this testing have been analyzed, and aging models fit to the data. Correlations relating several properties (thermal conductivity, energy absorption, weight loss and height decrease) to their rate of change in potential storage environments have been developed. Combined with an estimate of the actual conditions the fiberboard experiences in KAMS, these models allow development of service life predictions. Some of the predicted degradation rates presented in this report are relatively extreme. However, these relate to environments that do not exist within KAMS, or would be postulated only as upset conditions that would not likely persist for an extended period. For a typical package with ∼10 watts internal heat load or less, and ambient temperatures below 90 deg F, the fiberboard experiences storage conditions less severe than any of the aging environments. Little or no degradation of the fiberboard is expected for typical storage conditions. It should be noted that the ultimate service life will be determined by the cumulative effect of degradation from all the conditions these packages might encounter. The assumptions and inputs behind the models in this report should be well understood before attempting to identify an actual service life in KAMS. Additional data continue to be collected to permit future refinements to the models and assumptions. For developing service life predictions, the ambient conditions within KAMS can be reasonably identified, and the temperature profiles within the various packages (with a range of heat loads and at varying locations within an array of packages) can be calculated. However, the humidity within

Rapid estimation of glucosinolate thermal degradation rate constants in leaves of Chinese kale and broccoli (Brassica oleracea) in two seasons.

Science.gov (United States)

Hennig, Kristin; Verkerk, Ruud; Bonnema, Guusje; Dekker, Matthijs

2012-08-15

Kinetic modeling was used as a tool to quantitatively estimate glucosinolate thermal degradation rate constants. Literature shows that thermal degradation rates differ in different vegetables. Well-characterized plant material, leaves of broccoli and Chinese kale plants grown in two seasons, was used in the study. It was shown that a first-order reaction is appropriate to model glucosinolate degradation independent from the season. No difference in degradation rate constants of structurally identical glucosinolates was found between broccoli and Chinese kale leaves when grown in the same season. However, glucosinolate degradation rate constants were highly affected by the season (20-80% increase in spring compared to autumn). These results suggest that differences in glucosinolate degradation rate constants can be due to variation in environmental as well as genetic factors. Furthermore, a methodology to estimate rate constants rapidly is provided to enable the analysis of high sample numbers for future studies.

Rate and extent of ruminal degradation of crude protein from ...

African Journals Online (AJOL)

Predicted crude protein degradation was calculated at rate constants for outflow of 0.04 and 0.06/h respect- ively. ... as buffers, an ionophore and an antibiotic according to general .... the non-bird resistant ('sweet') varieties. Ruminal .... have been affected by both the particle type and the math- ematical model we used.

Analysis on the capacity degradation mechanism of a series lithium-ion power battery pack based on inconsistency of capacity

International Nuclear Information System (INIS)

Wang Zhen-Po; Liu Peng; Wang Li-Fang

2013-01-01

The lithium-ion battery has been widely used as an energy source. Charge rate, discharge rate, and operating temperature are very important factors for the capacity degradations of power batteries and battery packs. Firstly, in this paper we make use of an accelerated life test and a statistical analysis method to establish the capacity accelerated degradation model under three constant stress parameters according to the degradation data, which are charge rate, discharge rate, and operating temperature, and then we propose a capacity degradation model according to the current residual capacity of a Li-ion cell under dynamic stress parameters. Secondly, we analyze the charge and discharge process of a series power battery pack and interpret the correlation between the capacity degradations of the battery pack and its charge/discharge rate. According to this cycling condition, we establish a capacity degradation model of a series power battery pack under inconsistent capacity of cells, and analyze the degradation mechanism with capacity variance and operating temperature difference. The comparative analysis of test results shows that the inconsistent operating temperatures of cells in the series power battery pack are the main cause of its degradation; when the difference between inconsistent temperatures is narrowed by 5 °C, the cycle life can be improved by more than 50%. Therefore, it effectively improves the cycle life of the series battery pack to reasonably assemble the batteries according to their capacities and to narrow the differences in operating temperature among cells. (interdisciplinary physics and related areas of science and technology)

In situ and laboratory determined first-order degradation rate constants of specific organic compounds in an aerobic aquifer

DEFF Research Database (Denmark)

Nielsen, P.H.; Bjerg, P.L.; Nielsen, P.

1996-01-01

In situ microcosms (ISM) and laboratory batch microcosms (LBM) were used for determination of the first-order degradation rate constants of benzene, toluene, o-xylene, nitrobenzene, naphthalene, biphenyl, o- and p-dichlorobenzene, 1,1,1 -trichloroethane, tetrachlorometane, trichloroethene......, tetrachloroethene, phenol, o-cresol, 2,4- and 2,6-dichlorophenol, 4,6-o-dichlorocresol, and o- and p-nitrophenol in an aerobic aquifer, All aromatic hydrocarbons were degraded in ISM and LBM experiments. The phenolic hydrocarbons were ail degraded in ISM experiments, but some failed to degrade in LBM experiments....... Chlorinated aliphatic hydrocarbons were degraded neither in ISM nor LBM experiments. Degradation rate constants were determined by a model accounting for kinetic sorption (bicontinuum model), lag phases, and first-order degradation. With a few exceptions, lag phases were less than 2 weeks in both ISM and LBM...

Degradation rate of vitamin B6 on red chili pepper drying by blanching-brine-calcium pretreatment

Directory of Open Access Journals (Sweden)

Uma Fadzilia Arifin

2017-12-01

Full Text Available Drying is one of the alternatives to prevent spoilage in red chili pepper by removing moisture content. Red chili pepper (Capsicum frutescens has complex nutrition components such as vitamins and bioactive compound. However, vitamin B6 content in chili can degrade significantly in drying process by heat. This research studied degradation rate of vitamin B6 in chili drying process under various pretreatments and temperatures. In this study, post-harvest chili before dried was pretreated by blanching, osmotic dehydration with brine, immersing in calcium chloride solution and the combination of all them. They were dried in tray dyer at various temperatures 40°C, 50°C, 60°C and 70°C. Degradation of vitamin B6 content was analyzed every 2 hours by High-Performance Liquid Chromatography for 8 hours. Results showed that blanching-brine-calcium pretreatment was expected to reduce drying time and retain high content of vitamin B6 in red chili pepper. The degradation rate of vitamin B6 in chili followed second-order reaction. The degradation rate was influenced by temperature change referring to Arrhenius equation with activation energy was about 31.97 kJ/ mol K and constant rate (k0 was 3.769. Therefore, the vitamin B6 retention can be estimated at various pretreatments, times and temperatures. Furthermore, the favorable drying conditions can be evaluated.

Degradation rate of praziquantel and fenbendazole in rainbow trout following oral administration.

Science.gov (United States)

Soukupova-Markova, Zdenka; Doubkova, Veronika; Marsalek, Petr; Svobodova, Zdenka; Papezikova, Ivana; Lang, Stepan; Navratil, Stanislav; Palikova, Miroslava

2015-01-01

The aim of this study was to evaluate and compare the rate of degradation and elimination of praziquantel and fenbendazole antiparasitics following oral administration to salmonids. In addition, we determine whether the length of the legal withdrawal period is sufficient for complete elimination of antiparasitic residue from the body. The use of these drugs in fish is currently considered off-label and data on degradation are not available for rainbow trout. The model species for this experiment was the rainbow trout (Oncorhynchus mykiss) and praziquantel and fenbendazole were chosen for experimental therapy. Both drugs were administered into the gastrointestinal tract using a stomach tube. Concentrations of fenbendazole and praziquantel were established through high performance liquid chromatography-tandem mass spectrometry. Our results show that concentrations of praziquantel and fenbendazole reach their maximum in the body within 24 hours of administration, with concentrations dropping sharply over the following 24 hours. With one exception, when trace amounts of both substances were found in blood plasma, the drugs were completely degraded and eliminated from the body by the end of the experiment (corresponding to 497.6 degree days). Praziquantel and fenbendazole both show a high rate of degradation and elimination from fish. As both substances were eliminated from the body within the required withdrawal period (i.e. within 500 degree days) they can be safely used based on current knowledge of their therapeutic effect for treating helminth infections.

Environmental degradation of 316 stainless steel in high temperature low cycle fatigue

Science.gov (United States)

Kalluri, Sreeramesh; Manson, S. Stanford; Halford, Gary R.

1987-01-01

Procedures based on modification of the conventional Strainrange Partitioning method are proposed to characterize the time-dependent degradation of engineering alloys in high-temperature, low-cycle fatigue. Creep-fatigue experiments were conducted in air using different waveforms of loading on 316 stainless steel at 816 C (1500 F) to determine the effect of exposure time on cyclic life. Reductions in the partitioned cyclic lives were observed with an increase in the time of exposure (or with the corresponding decrease in the steady-state creep rate) for all the waveforms involving creep strain. Excellent correlations of the experimental data were obtained by modifying the Conventional Strainrange Partitioning life relationships involving creep strain using a power-law term of either: (1) time of exposure, or (2) steady-state creep rate of the creep-fatigue test. Environmental degradation due to oxidation, material degradation due to the precipitation of carbides along the grain boundaries and detrimental deformation modes associated with the prolonged periods of creep were observed to be the main mechanisms responsible for life reductions at long exposure times.

A kernel principal component analysis–based degradation model and remaining useful life estimation for the turbofan engine

Directory of Open Access Journals (Sweden)

Delong Feng

2016-05-01

Full Text Available Remaining useful life estimation of the prognostics and health management technique is a complicated and difficult research question for maintenance. In this article, we consider the problem of prognostics modeling and estimation of the turbofan engine under complicated circumstances and propose a kernel principal component analysis–based degradation model and remaining useful life estimation method for such aircraft engine. We first analyze the output data created by the turbofan engine thermodynamic simulation that is based on the kernel principal component analysis method and then distinguish the qualitative and quantitative relationships between the key factors. Next, we build a degradation model for the engine fault based on the following assumptions: the engine has only had constant failure (i.e. no sudden failure is included, and the engine has a Wiener process, which is a covariate stand for the engine system drift. To predict the remaining useful life of the turbofan engine, we built a health index based on the degradation model and used the method of maximum likelihood and the data from the thermodynamic simulation model to estimate the parameters of this degradation model. Through the data analysis, we obtained a trend model of the regression curve line that fits with the actual statistical data. Based on the predicted health index model and the data trend model, we estimate the remaining useful life of the aircraft engine as the index reaches zero. At last, a case study involving engine simulation data demonstrates the precision and performance advantages of this prediction method that we propose. At last, a case study involving engine simulation data demonstrates the precision and performance advantages of this proposed method, the precision of the method can reach to 98.9% and the average precision is 95.8%.

Effect of Moisture Content of Chitin-Calcium Silicate on Rate of Degradation of Cefotaxime Sodium.

Science.gov (United States)

Al-Nimry, Suhair S; Alkhamis, Khouloud A

2018-04-01

Assessment of incompatibilities between active pharmaceutical ingredient and pharmaceutical excipients is an important part of preformulation studies. The objective of the work was to assess the effect of moisture content of chitin calcium silicate of two size ranges (two specific surface areas) on the rate of degradation of cefotaxime sodium. The surface area of the excipient was determined using adsorption method. The effect of moisture content of a given size range on the stability of the drug was determined at 40°C in the solid state. The moisture content was determined at the beginning and the end of the kinetic study using TGA. The degradation in solution was studied for comparison. Increasing the moisture content of the excipient of size range 63-180 μm (surface area 7.2 m 2 /g) from 3.88 to 8.06% increased the rate of degradation of the drug more than two times (from 0.0317 to 0.0718 h -1 ). While an opposite trend was observed for the excipient of size range moisture content moisture content of 8.54%, and the degradation in solid state at both moisture contents was higher than that in solution (0.0871 h -1 ). In conclusion, the rate of degradation in solid should be studied taking into consideration the specific surface area and moisture content of the excipient at the storage condition and it may be higher than that in solution.

Fatigue life prediction in woven carbon fabric polyester composites

International Nuclear Information System (INIS)

Khan, Z.; Al-Sulaiman, F.S.; Farooqi, J.K.

1999-01-01

An analytical model, based on stiffness degradation during fatigue loading, which has been used for fatigue life predictions in the Fiber Reinforced Plastics (FRP), is employed to examine its validity to the fatigue life predictions in the Woven Fabric Reinforced Plastics. The rate of stiffness degradation (dE/dN) has been obtained from the constant amplitude fatigue testing of 8-ply coupons made from prepreg plain-weave woven carbon-carbon fabric having a polyester resin as the matrix material. The test coupons had three different ply stacking sequences, namely, the unidirectional (0)8,and two off axis plied (0,0,+45,-45)s, and (+45,-45,0,0)s orientations. The estimated fatigue lives obtained from the damage rate function dD/dN, which in turn was a function of the stiffness degradation rate dE/dN, were compared with the experimentally observed fatigue life data. It is shown that the stiffness degradation model provides reasonably good correlation between the analytically determined fatigue lives and the experimentally observed fatigue for the plain-weave woven Carbon-Carbon Fabric Reinforced Plastic Composites. (author)

Abiotic degradation of plastic films

Science.gov (United States)

Ángeles-López, Y. G.; Gutiérrez-Mayen, A. M.; Velasco-Pérez, M.; Beltrán-Villavicencio, M.; Vázquez-Morillas, A.; Cano-Blanco, M.

2017-01-01

Degradable plastics have been promoted as an option to mitigate the environmental impacts of plastic waste. However, there is no certainty about its degradability under different environmental conditions. The effect of accelerated weathering (AW), natural weathering (NW) and thermal oxidation (TO) on different plastics (high density polyethylene, HDPE; oxodegradable high density polyethylene, HDPE-oxo; compostable plastic, Ecovio ® metalized polypropylene, PP; and oxodegradable metalized polypropylene, PP-oxo) was studied. Plastics films were exposed to AW per 110 hours; to NW per 90 days; and to TO per 30 days. Plastic films exposed to AW and NW showed a general loss on mechanical properties. The highest reduction in elongation at break on AW occurred to HDPE-oxo (from 400.4% to 20.9%) and was higher than 90% for HDPE, HDPE-oxo, Ecovio ® and PP-oxo in NW. No substantial evidence of degradation was found on plastics exposed to TO. Oxo-plastics showed higher degradation rates than their conventional counterparts, and the compostable plastic was resistant to degradation in the studied abiotic conditions. This study shows that degradation of plastics in real life conditions will vary depending in both, their composition and the environment.

Measurement bias dependence of enhanced bipolar gain degradation at low dose rates

International Nuclear Information System (INIS)

Witczak, S.C.; Lacoe, R.C.; Mayer, D.C.; Fleetwood, D.M.

1998-03-01

Oxide trapped charge, field effects from emitter metallization, and high level injection phenomena moderate enhanced gain degradation of lateral pnp transistors at low dose rates. Hardness assurance tests at elevated irradiation temperatures require larger design margins for low power measurement biases

Intelligent Prognostic Framework for Degradation Assessment and Remaining Useful Life Estimation of Photovoltaic Module

Directory of Open Access Journals (Sweden)

Nabil Laayouj

2016-12-01

Full Text Available All industrial systems and machines are subjected to degradation processes, which can be related to the operating conditions. This degradation can cause unwanted stops at any time and major maintenance work sometimes. The accurate prediction of the remaining useful life (RUL is an important challenge in condition-based maintenance. Prognostic activity allows estimating the RUL before failure occurs and triggering actions to mitigate faults in time when needed. In this study, a new smart prognostic method for photovoltaic module health degradation was developed based on two approaches to achieve more accurate predictions: online diagnosis and data-driven prognosis. This framework of forecasting integrates the strengths of real-time monitoring in the first approach and relevant vector machine in the second. The results show that the proposed method is plausible due to its good prediction of RUL and can be effectively applied to many systems for monitoring and prognostics.

Physical mechanisms contributing to enhanced bipolar gain degradation at low dose rates

International Nuclear Information System (INIS)

Fleetwood, D.M.; Reber, R.A. Jr.; Winokur, P.S.; Kosier, S.L.; Schrimpf, R.D.; Wei, A.; DeLaus, M.; Combs, W.E.; Pease, R.L.

1994-01-01

The authors have performed capacitance-voltage (C-V) and thermally-stimulated-current (TSC) measurements on non-radiation-hard MOS capacitors simulating screen oxides of modern bipolar technologies. For 0-V irradiation of ∼25 C, the net trapped-positive-charge density (N ox ) inferred from midgap C-V shifts is ∼25--40% greater for low-dose-rate ( 2 )/s) than for high-dose-rate (> 100 rad(SiO 2 )/s) exposure. Device modeling shows that such a difference in screen-oxide N ox is enough to account for the enhanced low-rate gain degradation often observed in bipolar devices, due to the ∼ exp(N ox 2 ) dependence of the excess base current. At the higher rates, TSC measurements reveal a ∼10% decrease in trapped-hole density over low rates. Also, at high rates, up to ∼2.5-times as many trapped holes are compensated by electrons in border traps than at low rates for these devices and irradiation conditions. Both the reduction in trapped-hole density and increased charge compensation reduce the high-rate midgap shift. A physical model is developed which suggests that both effects are caused by time-dependent space charge in the bulk of these soft oxides associated with slowly transporting and/or metastably trapped holes (e.g., in Eδ' centers). On the basis of this model, bipolar transistors and screen-oxide capacitors were irradiated at 60 C at 200 rad(SiO 2 )/s in a successful effort to match low-rate damage. these surprising results provide insight into enhanced low-rate bipolar gain degradation and suggest potentially promising new approaches to bipolar and BiCMOS hardness assurance for space applications

Rate of atrazine mineralisation in New Zealand topsoils and subsoils depends on numbers of specialist atrazine-degrading microorganisms

International Nuclear Information System (INIS)

Sparling, G.; Fraser, R.; Aislabie, J.; Dragten, R.

1998-01-01

Full text: The herbicide atrazine (2-chloro-4-ethylamino-6-isopropylamino-1,3,5-s-triazine) is widely used in horticulture and arable farming in New Zealand and there is a trend towards increasing concentrations in aquifers and ground waters. Microbial degradation is considered a major route whereby atrazine is decomposed in soil. Microbial activity declines rapidly with depth of soil, so to predict the risks of atrazine reaching aquifers, we need to know the rates of mineralisation at different depths in the soil profile. We measured the rates of mineralisation of [U] 14 C-ring-labelled atrazine in topsoils and subsoils of two sandy loam soils and an allophanic soil under a range of temperature and moisture conditions. The numbers of atrazine-degrading organisms were measured using a most-probable number method based on the mineralisation of [U] 14 C-ring-labelled atrazine to 14 CO 2 . Numbers of atrazine-degraders and rates of mineralisation were generally very low in subsoils. However, one subsoil had unusually high numbers of atrazine-degrading microbes and showed equivalent rates of mineralisation rates to those in the surface soil. The rate of atrazine mineralisation could be predicted from the number of atrazine-degrading microbes and the cation exchange capacity of the soil (R 2 = 0.86). A large amount (54-77%) of 14 C remained in the soil as non-extractable residues after 263 days but only trace amounts of atrazine were detectable

Effect of indoor climate on the rate and degradation mechanism of plasticized poly (vinyl chloride)

DEFF Research Database (Denmark)

Shashoua, Yvonne

2003-01-01

Many PVC materials deteriorate only 5 years after manufacture. The extent, rate and mechanisms of deterioration of model and naturally aged PVC containing di (2-ethylhexyl) phthalate (DEHP), have been examined during thermal ageing in various environments. Weight loss was used to quantify loss...... inhibited degradation of the PVC polymer, therefore when it was lost, discolouration, tackiness and embrittlement resulted. Less plasticized materials degraded more rapidly than those more highly plasticized. Degradation was inhibited in both model sheets and naturally aged materials by enclosing them...

Proxy-rated quality of life in Alzheimer's disease

DEFF Research Database (Denmark)

Vogel, Asmus; Bhattacharya, Suvosree; Waldorff, Frans Boch

2012-01-01

The study investigated the change in proxy rated quality of life (QoL) of a large cohort of home living patients with Alzheimer's disease (AD) over a period of 36 months.......The study investigated the change in proxy rated quality of life (QoL) of a large cohort of home living patients with Alzheimer's disease (AD) over a period of 36 months....

Tunable Degradation Rate and Favorable Bioactivity of Porous Calcium Sulfate Scaffolds by Introducing Nano-Hydroxyapatite

Directory of Open Access Journals (Sweden)

Jianhua Zhou

2016-12-01

Full Text Available The bone scaffolds should possess suitable physicochemical properties and osteogenic activities. In this study, porous calcium sulfate (CaSO4 scaffolds were fabricated successfully via selected laser sintering (SLS. Nano-hydroxyapatite (nHAp, a bioactive material with a low degradation rate, was introduced into CaSO4 scaffolds to overcome the overquick absorption. The results demonstrated that nHAp could not only control the degradation rate of scaffolds by adjusting their content, but also improve the pH environment by alleviating the acidification progress during the degradation of CaSO4 scaffolds. Moreover, the improved scaffolds were covered completely with the apatite spherulites in simulated body fluid (SBF, showing their favorable bioactivity. In addition, the compression strength and fracture toughness were distinctly enhanced, which could be ascribed to large specific area of nHAp and the corresponding stress transfer.

Explanation of enhanced mechanical degradation rate for radiation- aged polyolefins as the aging temperature is decreased

International Nuclear Information System (INIS)

Gillen, K.T.; Clough, R.L.; Wise, J.; Malone, M.G.

1994-01-01

Degradation rates are normally increased by increasing the responsible environmental stresses. We describe results for a semi-crystalline, crosslinked polyolefin material that contradicts this assumption. In particular, under combined radiation plus thermal environments, this material mechanically degrades much faster at room temperature than it does at elevated temperatures. The probable explanation for this phenomenon relates to the importance on mechanical properties of the tie molecules connecting crystalline and amorphous regions. Partial melting and reforming/ reorganization of crystallites occurs throughout the crystalline melting region (at least room temperature up to 126 C), with the rate of such processes increasing with an increase in temperature. At low temperatures, this process is sufficiently slow such that a large percentage of the radiation-damaged tie molecules will still connect the amorphous and crystalline regions at the end of aging, leading to rapid reductions in tensile properties. At higher temperatures, the enhanced annealing rate will lead, during the aging, to the establishment of new, undamaged tie molecules connecting crystalline and amorphous regions. This healing process will reduce the degradation rate. Evidence in support of this model is presented

DNA Profiling Success Rates from Degraded Skeletal Remains in Guatemala.

Science.gov (United States)

Johnston, Emma; Stephenson, Mishel

2016-07-01

No data are available regarding the success of DNA Short Tandem Repeat (STR) profiling from degraded skeletal remains in Guatemala. Therefore, DNA profiling success rates relating to 2595 skeletons from eleven cases at the Forensic Anthropology Foundation of Guatemala (FAFG) are presented. The typical postmortem interval was 30 years. DNA was extracted from bone powder and amplified using Identifiler and Minifler. DNA profiling success rates differed between cases, ranging from 50.8% to 7.0%, the overall success rate for samples was 36.3%. The best DNA profiling success rates were obtained from femur (36.2%) and tooth (33.7%) samples. DNA profiles were significantly better from lower body bones than upper body bones (p = <0.0001). Bone samples from males gave significantly better profiles than samples from females (p = <0.0001). These results are believed to be related to bone density. The findings are important for designing forensic DNA sampling strategies in future victim recovery investigations. © 2016 American Academy of Forensic Sciences.

High temperature degradation in power plants and refineries

Directory of Open Access Journals (Sweden)

Furtado Heloisa Cunha

2004-01-01

Full Text Available Thermal power plants and refineries around the world share many of the same problems, namely aging equipment, high costs of replacement, and the need to produce more efficiently while being increasingly concerned with issues of safety and reliability. For equipment operating at high temperature, there are many different mechanisms of degradation, some of which interact, and the rate of accumulation of damage is not simple to predict. The paper discusses the mechanisms of degradation at high temperature and methods of assessment of such damage and of the remaining safe life for operation.

Searching for life on Mars: degradation of surfactant solutions used in organic extraction experiments.

Science.gov (United States)

Court, Richard W; Sims, Mark R; Cullen, David C; Sephton, Mark A

2014-09-01

Life-detection instruments on future Mars missions may use surfactant solutions to extract organic matter from samples of martian rocks. The thermal and radiation environments of space and Mars are capable of degrading these solutions, thereby reducing their ability to dissolve organic species. Successful extraction and detection of biosignatures on Mars requires an understanding of how degradation in extraterrestrial environments can affect surfactant performance. We exposed solutions of the surfactants polysorbate 80 (PS80), Zonyl FS-300, and poly[dimethylsiloxane-co-[3-(2-(2-hydroxyethoxy)ethoxy)propyl]methylsiloxane] (PDMSHEPMS) to elevated radiation and heat levels, combined with prolonged storage. Degradation was investigated by measuring changes in pH and electrical conductivity and by using the degraded solutions to extract a suite of organic compounds spiked onto grains of the martian soil simulant JSC Mars-1. Results indicate that the proton fluences expected during a mission to Mars do not cause significant degradation of surfactant compounds. Solutions of PS80 or PDMSHEPMS stored at -20 °C are able to extract the spiked standards with acceptable recovery efficiencies. Extraction efficiencies for spiked standards decrease progressively with increasing temperature, and prolonged storage at 60°C renders the surfactant solutions ineffective. Neither the presence of ascorbic acid nor the choice of solvent unequivocally alters the efficiency of extraction of the spiked standards. Since degradation of polysorbates has the potential to produce organic compounds that could be mistaken for indigenous martian organic matter, the polysiloxane PDMSHEPMS may be a superior choice of surfactant for the exploration of Mars.

Lifetime Evaluation of Grid-Connected PV Inverters Considering Panel Degradation Rates and Installation Sites

OpenAIRE

Sangwongwanich, Ariya; Yang, Yongheng; Sera, Dezso; Blaabjerg, Frede

2018-01-01

Lifetime of PV inverters is affected by the installation sites related to different solar irradiance and ambient temperature profiles (also referred to as mission profiles). In fact, the installation site also affects the degradation rate of the PV panels, and thus long-term energy production and reliability. Prior-art lifetime analysis in PV inverters has not yet investigated the impact of PV panel degradations. This paper thus evaluates the lifetime of PV inverters considering panel degrada...

Fractional rate of degradation (kd) of starch in the rumen and its ...

African Journals Online (AJOL)

Fractional rate of degradation (kd) of fermentable nutrients in the rumen is an important parameter in modern feed evaluation systems based on mechanistic models. Estimates of kd for starch was obtained on 19 starch sources originating from barley, wheat, oat, maize and peas and treated in different ways both chemically ...

Scaling of Polymer Degradation Rate within a High-Reynolds-Number Turbulent Boundary Layer

Science.gov (United States)

Elbing, Brian; Solomon, Michael; Perlin, Marc; Dowling, David; Ceccio, Steven

2009-11-01

An experiment conducted at the U.S. Navy's Large Cavitation Channel on a 12.9 m long flat-plate test model produced the first quantitative measurements of polymer molecular weight within a turbulent boundary layer. Testing was conducted at speeds to 20 m/s and downstream distance based Reynolds numbers to 220 million. These results showed that the rate of polymer degradation by scission of the polymer chains increases with increased speed, downstream distance and surface roughness. With the surface fully rough at 20 m/s there was no measureable level of drag reduction at the first measurement location (0.56 m downstream of injection). These results are scaled with the assumption that the rate of degradation is dependent on the polymer residence time in the flow and the local shear rate. A successful collapse of the data within the measurement uncertainty was achieved over a range of flow speed (6.6 to 20 m/s), surface roughness (smooth and fully rough) and downstream distance from injection (0.56 to 9.28 m).

Prediction of ozone tropospheric degradation rate constant of organic compounds by using artificial neural networks

International Nuclear Information System (INIS)

Fatemi, M.H.

2006-01-01

Ozone tropospheric degradation of organic compound is very important in environmental chemistry. The lifetime of organic chemicals in the atmosphere can be calculated from the knowledge of the rate constant of their reaction with free radicals such as OH and NO 3 or O 3 . In the present work, the rate constant for the tropospheric degradation of 137 organic compounds by reaction with ozone, the least widely and successfully modeled degradation process, are predicted by quantitative structure activity relationships modeling based on a variety of theoretical descriptors, which screened and selected by genetic algorithm variable subset selection procedure. These descriptors which can be used as inputs for generated artificial neural networks are; HOMO-LUMO gap, number of double bonds, number of single bonds, maximum net charge on C atom, minimum (>0.1) bond order of C atom and Minimum e-e repulsion of H atom. After generation, optimization and training of artificial neural network, network was used for the prediction of log KO 3 for the validation set. The root mean square error for the neural network calculated log KO 3 for training, prediction and validation set are 0.357, 0.460 and 0.481, respectively, which are smaller than those obtained by multiple linear regressions model (1.217, 0.870 and 0.968, respectively). Results obtained reveal the reliability and good predictivity of neural network model for the prediction of ozone tropospheric degradations rate constant of organic compounds

Rate of antioxidant degradation and color variations in dehydrated apples as related to water activity.

Science.gov (United States)

Lavelli, Vera; Vantaggi, Claudia

2009-06-10

Dehydrated apples were studied to evaluate the effects of water activity on the stability of their antioxidants and color. Apples were freeze-dried, ground, then equilibrated, and stored at eight water activity levels, ranging from 0.058 to 0.747, at 40 degrees C. Their contents of hydroxycinnamic acids, dihydrochalcones, catechin, epicatechin, polymeric flavan-3-ols, and hydroxymethylfurfural, their antioxidant activity values, and their Hunter colorimetric parameters were analyzed at different storage times. Antioxidant degradation followed pseudo-first-order kinetics and was accelerated by increasing the water activity. The order of antioxidant stability in the products at water activity levels below 0.316 was catechin, epicatechin, and ascorbic acid acid acid; however, in the products at water activity levels above 0.316, the degradation of all antioxidants was very fast. The hydroxymethylfurfural formation rate increased exponentially during storage, especially at high water activity levels. The antioxidant activity of the dehydrated apples decreased during storage, consistent with antioxidant loss. The variations of the colorimetric parameters, namely, lightness (L*), redness (a*), and yellowness (b*), followed pseudo-zero-order kinetics and were accelerated by increasing water activity. All analytical indices indicated that the dehydrated apples were stable at water activity levels below 0.316, with the degradation rate accelerating upon exposure to higher relative humidities. Above 0.316, a small increase in water activity of the product would sharply increase the degradation rate constants for both antioxidant and color variations.

Dependent interest and transition rates in life insurance

DEFF Research Database (Denmark)

Buchardt, Kristian

2014-01-01

For market consistent life insurance liabilities modelled with a multi-state Markov chain, it is of importance to consider the interest and transition rates as stochastic processes, for example in order to consider hedging possibilities of the risks, and for risk measurement. In the literature......, this is usually done with an assumption of independence between the interest and transition rates. In this paper, it is shown how to valuate life insurance liabilities using affine processes for modelling dependent interest and transition rates. This approach leads to the introduction of so-called dependent...... forward rates. We propose a specific model for surrender modelling, and within this model the dependent forward rates are calculated, and the market value and the Solvency II capital requirement are examined for a simple savings contract....

Effects of irradiation-degradated chitosan coating on quality and shelf-life of the fruits of Shatang Mandarin, Fortunella Margariat (LOUR) swingle and Lycopersicon Esculentum MILL. var. cerasiforme alef

International Nuclear Information System (INIS)

Chen Hao; Gao Peng; Gao Ya; Yang Zhirong; Sun Qun

2008-01-01

Effects of irradiation-degradated chiotosan of different molecular weight on weight loss, rotting rate, total acid, soluble solid content, and ascorbic acid in Shatang mandarin, Fortunella margarita (lour) Swingle, and Lycopersicon esculentum Mill. var. cerasiforme Alef during storage were investigated. The result showed that, compared to control, all chitosan treatment could significantly reduce weight loss and rotting rate, and maintain the content of total acid, soluble solid, and ascorbic acid. After 18 days of storage, treatment of chitosan with molecular weight of 6.6 x 10 4 Da showed the highest capability of decreasing the rotting rate in S. mandarin, F. margarita, L. esculentum by 71.11%, 66.01% and 70.22%, respectively; increasing total acid by 55.60%, 36.75% and 36.68%, soluble solid content by 49.06%, 25.75% and 49.46%, and ascorbic acid by 42.80%, 41.65% and 51.70%, respectively. Accordingly, irradiation-degradated chitosan coating could effectively prevent the rotting rate and preserve the quality of the three kinds of fruit during storage and thus prolong their shelf life to 18 days. (authors)

Accelerated thermal and radiation-oxidation combined degradation of electric cable insulation materials

International Nuclear Information System (INIS)

Yagi, Toshiaki; Seguchi, Tadao; Yoshida, Kenzo

1986-03-01

For the development of accelerated testing methodology to estimate the life time of electric cable, which is installed in radiation field such as a nuclear reactor containment vessel, radiation and thermal combined degradation of cable insulation and jacketing materials was studied. The materials were two types of formulated polyethylene, ethylene-propylene rubber, Hypalon, and Neoprene. With Co-60 γ-rays the materials were irradiated up to 0.5 MGy under vacuum and in oxygen under pressure, then exposed to thermal aging at elevated temperature in oxygen. The degradation was investigated by the tensile test, gelfraction, and swelling measurements. The thermal degradation rate for each sample increases with increase of oxygen concentration, i.e. oxygen pressure, during the aging, and tends to saturate above 0.2 MPa of oxygen pressure. Then, the effects of irradiation and the temperature on the thermal degradation rate were investigated at the oxygen pressure of 0.2 MPa in the temperature range from 110 deg C to 150 deg C. For all of samples irradiated in oxygen, the following thermal degradation rate was accelerated by several times comparing with unirradiated samples, while the rate of thermal degradation for the sample except Neoprene irradiated under vacuum was nearly equal to that of unirradiated one. By the analysis of thermal degradation rate against temperature using Arrhenius equation, it was found that the activation energy tends to decrease for the samples irradiated in oxidation condition. (author)

Degradation rates in thermophilic sludge processing - the liquid and the solid way

Energy Technology Data Exchange (ETDEWEB)

Mihaltz, P.; Kovacs, R.; Csikor, Zs.; Dahab, M.F.

2003-07-01

Two promising and well known techniques for sludge stabilization and pathogen destruction, the composting and autothermal thermophilic aerobic digestion (ATAD, often referred to as ''liquid composting'') have not yet undergone a comparative parallel study. This comparison is presented in this paper to identify - sometimes unusually (e.g. up to 30 mg O{sub 2} /gVS h) high - degradation rates, their main influencing parameters. For the ATAD we developed a well fitting modified two-substrate kinetic model quantitatively describing this process feature too - the clear signs of two substrate degradation also appears in most own and literature composting records. However compost process modelling needs as a prerequisite the clarification of the controlling transport mechanisms. Experimental conclusions suggest the dual role of local VS limitation closely connected with, but being behind the strong observed oxygen limitation, what is proposed for the explanation of composting process rates - essentially based on specific surface area controlled transport phenomena, justifying efforts to conduct the process at lower (<20 to 25%) moisture content and higher (>1000 1/m) specific surface area levels. (author)

Interest rate risk of life insurers: Evidence from accounting data

OpenAIRE

Möhlmann, Axel

2017-01-01

Life insurers are exposed to interest rate risk, and their liability side is typically more sensitive to interest rate changes than their asset side. This paper develops an accounting-based measure of interest rate sensitivity. My approach uses the coexistence of historical cost and market value accounting, which permits the observation of valuations for different discount rates. Using microdata, I show that German life insurers have a significant exposure to interest rate risk. However, ther...

A new approach to estimate the in situ fractional degradation rate of organic matter and nitrogen in wheat yeast concentrates

NARCIS (Netherlands)

De Jonge, L. H.; Van Laar, H.; Hendriks, W. H.; Dijkstra, J.

2015-01-01

In the classic in situ method, small particles are removed during rinsing and hence their fractional degradation rate cannot be determined. A new approach was developed to estimate the fractional degradation rate of nutrients in small particles. This approach was based on an alternative rinsing

Determination of rate constants and branching ratios for TCE degradation by zero-valent iron using a chain decay multispecies model.

Science.gov (United States)

Hwang, Hyoun-Tae; Jeen, Sung-Wook; Sudicky, Edward A; Illman, Walter A

2015-01-01

The applicability of a newly-developed chain-decay multispecies model (CMM) was validated by obtaining kinetic rate constants and branching ratios along the reaction pathways of trichloroethene (TCE) reduction by zero-valent iron (ZVI) from column experiments. Changes in rate constants and branching ratios for individual reactions for degradation products over time for two columns under different geochemical conditions were examined to provide ranges of those parameters expected over the long-term. As compared to the column receiving deionized water, the column receiving dissolved CaCO3 showed higher mean degradation rates for TCE and all of its degradation products. However, the column experienced faster reactivity loss toward TCE degradation due to precipitation of secondary carbonate minerals, as indicated by a higher value for the ratio of maximum to minimum TCE degradation rate observed over time. From the calculated branching ratios, it was found that TCE and cis-dichloroethene (cis-DCE) were dominantly dechlorinated to chloroacetylene and acetylene, respectively, through reductive elimination for both columns. The CMM model, validated by the column test data in this study, provides a convenient tool to determine simultaneously the critical design parameters for permeable reactive barriers and natural attenuation such as rate constants and branching ratios. Copyright © 2015 Elsevier B.V. All rights reserved.

Lifetime design strategy for binary geothermal plants considering degradation of geothermal resource productivity

International Nuclear Information System (INIS)

Budisulistyo, Denny; Wong, Choon Seng; Krumdieck, Susan

2017-01-01

Highlights: • A new lifetime strategy for binary plants considering thermal resource degradations. • The net present value and energy return on investment are selected as indicators. • The results indicate that the design based on point 2 has the best revenue. • Improving plant performance by parameters adjustments and adaptable designs. - Abstract: This work proposes a lifetime design strategy for binary geothermal plants which takes into account heat resource degradation. A model of the resource temperature and mass flow rate decline over a 30 year plant life is developed from a survey of data. The standard approach to optimise a basic subcritical cycle of n-pentane working fluid and select component sizes is used for the resource characteristics in years 1, 7, 15 and 30. The performances of the four plants designed for the different resource conditions are then simulated over the plant life to obtain the best lifetime design. The net present value and energy return on investment are selected as the measures of merit. The production history of a real geothermal well in the Taupo Volcanic Zone, New Zealand, is used as a case study for the lifetime design strategy. The results indicate that the operational parameters (such as mass flow rate of n-pentane, inlet turbine pressure and air mass flow rate) and plant performance (net power output) decrease over the whole plant life. The best lifetime plant design was at year 7 with partly degraded conditions. This condition has the highest net present value at USD 6,894,615 and energy return on investment at 4.15. Detailed thermo-economic analysis was carried out with the aim of improving the plant performance to overcome the resource degradation in two ways: operational parameters adjustments and adaptable designs. The results shows that mass flow rates of n-pentane and air cooling should be adjusted to maintain the performance over the plant life. The plant design can also be adapted by installing a recuperator

Pressurized Hot Water Extraction of anthocyanins from red onion: A study on extraction and degradation rates

Energy Technology Data Exchange (ETDEWEB)

Petersson, Erik V.; Liu Jiayin; Sjoeberg, Per J.R.; Danielsson, Rolf [Uppsala University, Department of Physical and Analytical Chemistry, P.O. Box 599, SE-751 24, Uppsala (Sweden); Turner, Charlotta, E-mail: Charlotta.Turner@kemi.uu.se [Uppsala University, Department of Physical and Analytical Chemistry, P.O. Box 599, SE-751 24, Uppsala (Sweden)

2010-03-17

Pressurized Hot Water Extraction (PHWE) is a quick, efficient and environmentally friendly technique for extractions. However, when using PHWE to extract thermally unstable analytes, extraction and degradation effects occur at the same time, and thereby compete. At first, the extraction effect dominates, but degradation effects soon take over. In this paper, extraction and degradation rates of anthocyanins from red onion were studied with experiments in a static batch reactor at 110 deg. C. A total extraction curve was calculated with data from the actual extraction and degradation curves, showing that more anthocyanins, 21-36% depending on the species, could be extracted if no degradation occurred, but then longer extraction times would be required than those needed to reach the peak level in the apparent extraction curves. The results give information about the different kinetic processes competing during an extraction procedure.

Poly(amido-amine)-based hydrogels with tailored mechanical properties and degradation rates for tissue engineering.

Science.gov (United States)

Martello, Federico; Tocchio, Alessandro; Tamplenizza, Margherita; Gerges, Irini; Pistis, Valentina; Recenti, Rossella; Bortolin, Monica; Del Fabbro, Massimo; Argentiere, Simona; Milani, Paolo; Lenardi, Cristina

2014-03-01

Poly(amido-amine) (PAA) hydrogels containing the 2,2-bisacrylamidoacetic acid-4-amminobutyl guanidine monomeric unit have a known ability to enhance cellular adhesion by interacting with the arginin-glycin-aspartic acid (RGD)-binding αVβ3 integrin, expressed by a wide number of cell types. Scientific interest in this class of materials has traditionally been hampered by their poor mechanical properties and restricted range of degradation rate. Here we present the design of novel biocompatible, RGD-mimic PAA-based hydrogels with wide and tunable degradation rates as well as improved mechanical and biological properties for biomedical applications. This is achieved by radical polymerization of acrylamide-terminated PAA oligomers in both the presence and absence of 2-hydroxyethylmethacrylate. The degradation rate is found to be precisely tunable by adjusting the PAA oligomer molecular weight and acrylic co-monomer concentration in the starting reaction mixture. Cell adhesion and proliferation tests on Madin-Darby canine kidney epithelial cells show that PAA-based hydrogels have the capacity to promote cell adhesion up to 200% compared to the control. Mechanical tests show higher compressive strength of acrylic chain containing hydrogels compared to traditional PAA hydrogels. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Nuclear Radiation Degradation Study on HD Camera Based on CMOS Image Sensor at Different Dose Rates.

Science.gov (United States)

Wang, Congzheng; Hu, Song; Gao, Chunming; Feng, Chang

2018-02-08

In this work, we irradiated a high-definition (HD) industrial camera based on a commercial-off-the-shelf (COTS) CMOS image sensor (CIS) with Cobalt-60 gamma-rays. All components of the camera under test were fabricated without radiation hardening, except for the lens. The irradiation experiments of the HD camera under biased conditions were carried out at 1.0, 10.0, 20.0, 50.0 and 100.0 Gy/h. During the experiment, we found that the tested camera showed a remarkable degradation after irradiation and differed in the dose rates. With the increase of dose rate, the same target images become brighter. Under the same dose rate, the radiation effect in bright area is lower than that in dark area. Under different dose rates, the higher the dose rate is, the worse the radiation effect will be in both bright and dark areas. And the standard deviations of bright and dark areas become greater. Furthermore, through the progressive degradation analysis of the captured image, experimental results demonstrate that the attenuation of signal to noise ratio (SNR) versus radiation time is not obvious at the same dose rate, and the degradation is more and more serious with increasing dose rate. Additionally, the decrease rate of SNR at 20.0, 50.0 and 100.0 Gy/h is far greater than that at 1.0 and 10.0 Gy/h. Even so, we confirm that the HD industrial camera is still working at 10.0 Gy/h during the 8 h of measurements, with a moderate decrease of the SNR (5 dB). The work is valuable and can provide suggestion for camera users in the radiation field.

Rating Evaluation of the Quality of Life in Russian Regions

Directory of Open Access Journals (Sweden)

Sergey Valentinovich Kuznetsov

2017-03-01

Full Text Available In the article, the authors consider the quality of life as an objective and its indicators as the criteria for evaluating the effectiveness of balanced spatial development. The problem of measuring the quality of life has a complex and integrated nature, therefore, we should develop the practice of ratings in its spatial comparisons. The article demonstrates the possibility of using the rating lists of the quality of life of Russian regions by the rating agency “RIA Rating” for 2013–2015 as an information tool for the analysis of the efficiency and effectiveness of the public development of the regional administration. The authors have concluded that with a consecutive growth of an average value of the integrated rating index of quality of life, the different ways of assessing the degree of differentiation of the regions according to the quality of life provide conflicting results. It is necessary to pay attention not so much to ranging and grading of regions as to their classification depending on to the nature of typical problems. Therefore, the rating scale is structured on the basis of the “problematic principle of regional grouping”. The authors have proposed the method of the gradation of the rating scale, allowing to take into account the direction of change of the region’s position in the ranking. The relevance of the rating as a key information tool to reduce the regional differentiation of the life quality of the population among the regulatory bodies and civil society will increase if: it is also used for other subnational entities of the Russian Federation; there is the use of econometric and computational capabilities of high-tech software systems for a posteriori analysis and models for strategic forecasting of the rankings; there is the search of a synergistic effect from a variety of estimates of the degree of spatial development.

A probabilistic degradation model for the estimation of the remaining life distribution of feeders

International Nuclear Information System (INIS)

Yuan, X.-X.; Pandey, M.D.; Bickel, G.A.

2006-01-01

Wall thinning due to flow accelerated corrosion (FAC) is a pervasive form of degradation in the outlet feeder pipes of the primary heat transport system of CANDU reactors. The prediction of the end-of-life of a feeder from wall thickness measurement data is confounded by the sampling and temporal uncertainties associated with the FAC degradation phenomenon. Traditional regression-based statistical methods deal with only the sampling uncertainties, leaving the temporal uncertainties unresolved. This paper presents an advanced probabilistic model, which is able to integrate the temporal uncertainties into the prediction of lifetime. In particular, a random gamma process model is proposed to model the FAC process and it is calibrated with a set of wall thickness measurements using the method of maximum likelihood. This information can be used to establish an optimum strategy for inspection and replacement of feeders. (author)

Development of a methodology for life cycle building energy ratings

International Nuclear Information System (INIS)

Hernandez, Patxi; Kenny, Paul

2011-01-01

Traditionally the majority of building energy use has been linked to its operation (heating, cooling, lighting, etc.), and much attention has been directed to reduce this energy use through technical innovation, regulatory control and assessed through a wide range of rating methods. However buildings generally employ an increasing amount of materials and systems to reduce the energy use in operation, and energy embodied in these can constitute an important part of the building's life cycle energy use. For buildings with 'zero-energy' use in operation the embodied energy is indeed the only life cycle energy use. This is not addressed by current building energy assessment and rating methods. This paper proposes a methodology to extend building energy assessment and rating methods accounting for embodied energy of building components and systems. The methodology is applied to the EU Building Energy Rating method and, as an illustration, as implemented in Irish domestic buildings. A case study dwelling is used to illustrate the importance of embodied energy on life cycle energy performance, particularly relevant when energy use in operation tends to zero. The use of the Net Energy Ratio as an indicator to select appropriate building improvement measures is also presented and discussed. - Highlights: → The definitions for 'zero energy buildings' and current building energy ratings are examined. → There is a need to integrate a life cycle perspective within building energy ratings. → A life cycle building energy rating method (LC-BER), including embodied energy is presented. → Net Energy Ratio is proposed as an indicator to select building energy improvement options.

Investigating the effect of artists’ paint formulation on degradation rates of TiO2‑based oil paints

NARCIS (Netherlands)

van Driel, B.A.; van den Berg, K. J.; Smout, M.; Dekker, N; Kooyman, P.J.; Dik, J.

2018-01-01

This study reports on the effect of artists’ paint formulation on degradation rates of TiO2-based oil paints. Titanium white oil paint exists in a multitude of different recipes, and the effect of the formulation on photocatalytic binder
degradation kinetics is unknown. These formulations

Nuclear Radiation Degradation Study on HD Camera Based on CMOS Image Sensor at Different Dose Rates

Directory of Open Access Journals (Sweden)

Congzheng Wang

2018-02-01

Full Text Available In this work, we irradiated a high-definition (HD industrial camera based on a commercial-off-the-shelf (COTS CMOS image sensor (CIS with Cobalt-60 gamma-rays. All components of the camera under test were fabricated without radiation hardening, except for the lens. The irradiation experiments of the HD camera under biased conditions were carried out at 1.0, 10.0, 20.0, 50.0 and 100.0 Gy/h. During the experiment, we found that the tested camera showed a remarkable degradation after irradiation and differed in the dose rates. With the increase of dose rate, the same target images become brighter. Under the same dose rate, the radiation effect in bright area is lower than that in dark area. Under different dose rates, the higher the dose rate is, the worse the radiation effect will be in both bright and dark areas. And the standard deviations of bright and dark areas become greater. Furthermore, through the progressive degradation analysis of the captured image, experimental results demonstrate that the attenuation of signal to noise ratio (SNR versus radiation time is not obvious at the same dose rate, and the degradation is more and more serious with increasing dose rate. Additionally, the decrease rate of SNR at 20.0, 50.0 and 100.0 Gy/h is far greater than that at 1.0 and 10.0 Gy/h. Even so, we confirm that the HD industrial camera is still working at 10.0 Gy/h during the 8 h of measurements, with a moderate decrease of the SNR (5 dB. The work is valuable and can provide suggestion for camera users in the radiation field.

Multiscale analysis of the radiooxidative degradation of EVA/EPDM composites. ATH filler and dose rate effect

Science.gov (United States)

Sidi, Ahmedou; Colombani, Juliette; Larché, Jean-François; Rivaton, Agnès

2018-01-01

This study is focused on the radiooxidative degradation of polymeric insulation of electric cables used in Nuclear Power Plants (NPPs). In order to investigate the degradation mechanisms of the insulation, model composites with ATH (Aluminium TriHydrate) filler and blends (without filler) based on a cross-linked mixture of EVA (Ethylene Vinyl Acetate) and EPDM (Ethylene Propylene Diene Monomer) were submitted to gamma-rays. In normal operating conditions of a NPP, the dose rate which electric cables are exposed to is around 0.1 Gy h-1. In this work, artificial accelerated ageing test process has been applied at a relatively low dose rate of 7 Gy h-1. Gamma-irradiations at higher dose rates typically used to accelerate the ageing, in the range 0.2-1 kGy h-1, were also carried out. The first part of the study is focused on irradiations performed at relatively low dose rate and is devoted to the highlighting of the radiooxidative degradation mechanisms of EVA/EPDM blend with and without ATH filler. Correlations between the evolutions of the chemical, morphological and mechanical/electrical properties of the materials occurring after the ageing process are presented. It is shown that the degradation process is governed by radical oxidation mechanism involving chain scissions leading to the formation of carboxylic acids as end-groups. One of the main effects of the ATH filler is the progressive loss of the mechanical properties of the composite upon radiooxidation whereas they are maintained in the case of the unfilled sample. Despite the oxidation of the polymer, no change in the electrical properties of the blend and of the composite could be observed. The second part of the study focuses on the dose rate effect. It is shown that one of the main consequences of an increase of the dose rate from 7 Gy h-1 to 0.2-1 kGy h-1 is a reduction of the chain scission process yield by a factor of about 20. Therefore, an important and consistent finding is that there are some

The effect of poly-β-hydroxyalkanoates degradation rate on nitrous oxide production in a denitrifying phosphorus removal system.

Science.gov (United States)

Wei, Yan; Wang, Shuying; Ma, Bin; Li, Xiyao; Yuan, Zhiguo; He, Yuelan; Peng, Yongzhen

2014-10-01

Poly-β-hydroxyalkanoates (PHAs) and free nitrous acid (FNA) have been revealed as significant factors causing nitrous oxide (N2O) production in denitrifying phosphorus removal systems. In this study, the effect of PHA degradation rate on N2O production was studied at low FNA levels. N2O production always maintained at approximately 40% of the amount of nitrite reduced independent of the PHA degradation rate. The electrons distributed to nitrite reduction were 1.6 times that to N2O reduction. This indicated that electron competition between these two steps was not affected by the PHA degradation rate. Continuous feed of nitrate was proposed, and demonstrated to reduce N2O accumulation by 75%. While being kept low, a possible compounding effect of a low-level FNA could not be ruled out. The sludge used likely contained both polyphosphate- and glycogen-accumulating organisms, and the results could not be simply attributed to either group of organisms. Copyright © 2014 Elsevier Ltd. All rights reserved.

Testing the ecotoxicology of vegetable versus mineral based lubricating oils: 1. Degradation rates using tropical marine microbes

International Nuclear Information System (INIS)

Mercurio, Philip; Burns, Kathryn A.; Negri, Andrew

2004-01-01

Vegetable-derived lubricants (VDL) might be more biodegradable than mineral-derived lubricants (MDL) due to the absence of high molecular weight aromatics, but this remains largely untested in tropical conditions. In this laboratory study, the degradation rates of 2-stroke, 4-stroke and hydraulic VDLs were compared with their MDL counterparts in the presence of mangrove and coral reef microbial communities. While MDLs were comprised largely of unresolved saturated and some aromatic hydrocarbons, their VDL counterparts contained, potentially more degradable, fatty acid methyl esters. Degradation of some VDL was observed by day 7, with the 2-stroke VDL markedly consumed by mangrove microorganisms and the hydraulic VDL degraded by both microorganism communities after this short period. All of the VDL groups were significantly more degraded than the comparable MDLs mineral oil lubricants over 14 days in the presence of either mangrove or coral reef microbial communities. In general the mangrove-sourced microorganisms more efficiently degraded the lubricants than reef-sourced microorganisms. - Vegetable-derived lubricants were more degradable than mineral oil lubricants

Testing the ecotoxicology of vegetable versus mineral based lubricating oils: 1. Degradation rates using tropical marine microbes

Energy Technology Data Exchange (ETDEWEB)

Mercurio, Philip; Burns, Kathryn A.; Negri, Andrew

2004-05-01

Vegetable-derived lubricants (VDL) might be more biodegradable than mineral-derived lubricants (MDL) due to the absence of high molecular weight aromatics, but this remains largely untested in tropical conditions. In this laboratory study, the degradation rates of 2-stroke, 4-stroke and hydraulic VDLs were compared with their MDL counterparts in the presence of mangrove and coral reef microbial communities. While MDLs were comprised largely of unresolved saturated and some aromatic hydrocarbons, their VDL counterparts contained, potentially more degradable, fatty acid methyl esters. Degradation of some VDL was observed by day 7, with the 2-stroke VDL markedly consumed by mangrove microorganisms and the hydraulic VDL degraded by both microorganism communities after this short period. All of the VDL groups were significantly more degraded than the comparable MDLs mineral oil lubricants over 14 days in the presence of either mangrove or coral reef microbial communities. In general the mangrove-sourced microorganisms more efficiently degraded the lubricants than reef-sourced microorganisms. - Vegetable-derived lubricants were more degradable than mineral oil lubricants.

Testing the ecotoxicology of vegetable versus mineral based lubricating oils: 1. Degradation rates using tropical marine microbes.

Science.gov (United States)

Mercurio, Philip; Burns, Kathryn A; Negri, Andrew

2004-05-01

Vegetable-derived lubricants (VDL) might be more biodegradable than mineral-derived lubricants (MDL) due to the absence of high molecular weight aromatics, but this remains largely untested in tropical conditions. In this laboratory study, the degradation rates of 2-stroke, 4-stroke and hydraulic VDLs were compared with their MDL counterparts in the presence of mangrove and coral reef microbial communities. While MDLs were comprised largely of unresolved saturated and some aromatic hydrocarbons, their VDL counterparts contained, potentially more degradable, fatty acid methyl esters. Degradation of some VDL was observed by day 7, with the 2-stroke VDL markedly consumed by mangrove microorganisms and the hydraulic VDL degraded by both microorganism communities after this short period. All of the VDL groups were significantly more degraded than the comparable MDLs mineral oil lubricants over 14 days in the presence of either mangrove or coral reef microbial communities. In general the mangrove-sourced microorganisms more efficiently degraded the lubricants than reef-sourced microorganisms.

The rate of incorporation and degradation of phenylalanine-14C by tissue slices of roosters fed a phenylalanine-free diet

International Nuclear Information System (INIS)

Ishibashi, Teru; Kametaka, Masao

1975-01-01

To investigate the reason why adult roosters maintain nitrogen equilibrium on a phenylalanine-free diet for long periods, the rates of incorporation and of degradation of phenylalanine, tyrosine- and isoleucine- 14 C by tissue slices of roosters on the control, phenylalanine-free or isoleucine-free diets were measured. The degradation rate of isoleucine by liver and muscle slices decreased significantly for the isoleucine-free diet. However, the degradation rate of phenylalanine- 14 C by liver slices for the phenylalanine-free diet was not significantly lower than that for the control diet in contrast to the previous observation in vivo. The incorporation rates of 14 C into liver and muscle proteins were not affected by the dietary conditions in this experiment except in the case of phenylalanine- 14 C by muscle slices for the phenylalanine-free diet. (auth.)

Joint optimisation of arbitrage profits and battery life degradation for grid storage application of battery electric vehicles

Science.gov (United States)

Kies, Alexander

2018-02-01

To meet European decarbonisation targets by 2050, the electrification of the transport sector is mandatory. Most electric vehicles rely on lithium-ion batteries, because they have a higher energy/power density and longer life span compared to other practical batteries such as zinc-carbon batteries. Electric vehicles can thus provide energy storage to support the system integration of generation from highly variable renewable sources, such as wind and photovoltaics (PV). However, charging/discharging causes batteries to degradate progressively with reduced capacity. In this study, we investigate the impact of the joint optimisation of arbitrage revenue and battery degradation of electric vehicle batteries in a simplified setting, where historical prices allow for market participation of battery electric vehicle owners. It is shown that the joint optimisation of both leads to stronger gains then the sum of both optimisation strategies and that including battery degradation into the model avoids state of charges close to the maximum at times. It can be concluded that degradation is an important aspect to consider in power system models, which incorporate any kind of lithium-ion battery storage.

Generation time, life history and the substitution rate of neutral mutations.

Science.gov (United States)

Lehtonen, Jussi; Lanfear, Robert

2014-11-01

Our understanding of molecular evolution is hampered by a lack of quantitative predictions about how life-history (LH) traits should correlate with substitution rates. Comparative studies have shown that neutral substitution rates vary substantially between species, and evidence shows that much of this diversity is associated with variation in LH traits. However, while these studies often agree, some unexplained and contradictory results have emerged. Explaining these results is difficult without a clear theoretical understanding of the problem. In this study, we derive predictions for the relationships between LH traits and substitution rates in iteroparous species by using demographic theory to relate commonly measured life-history traits to genetic generation time, and by implication to neutral substitution rates. This provides some surprisingly simple explanations for otherwise confusing patterns, such as the association between fecundity and substitution rates. The same framework can be applied to more complex life histories if full life-tables are available. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Diversification rates and species richness across the Tree of Life.

Science.gov (United States)

Scholl, Joshua P; Wiens, John J

2016-09-14

Species richness varies dramatically among clades across the Tree of Life, by over a million-fold in some cases (e.g. placozoans versus arthropods). Two major explanations for differences in richness among clades are the clade-age hypothesis (i.e. species-rich clades are older) and the diversification-rate hypothesis (i.e. species-rich clades diversify more rapidly, where diversification rate is the net balance of speciation and extinction over time). Here, we examine patterns of variation in diversification rates across the Tree of Life. We address how rates vary across higher taxa, whether rates within higher taxa are related to the subclades within them, and how diversification rates of clades are related to their species richness. We find substantial variation in diversification rates, with rates in plants nearly twice as high as in animals, and rates in some eukaryotes approximately 10-fold faster than prokaryotes. Rates for each kingdom-level clade are then significantly related to the subclades within them. Although caution is needed when interpreting relationships between diversification rates and richness, a positive relationship between the two is not inevitable. We find that variation in diversification rates seems to explain most variation in richness among clades across the Tree of Life, in contrast to the conclusions of previous studies. © 2016 The Author(s).

Degradation analysis of some synthetic and bio-insecticides sprayed on okra crop using HPLC

International Nuclear Information System (INIS)

Abar, M.F.; Haq, M.A.; Yasmin, N.; Khan, M.F.U.

2012-01-01

This study aimed to find out the degradation of three conventional and two bio-insecticides sprayed on okra crop. Imidacloprid, Endosulfan and Profenofos were selected as convectional and biosal and spinosad as bioinsecticide. The insecticides were sprayed at the rates of 49.4, 642.2, 988, 35.5 and 158 g. a. i. ha/sup -1/ respectively. The insecticide residues were analyzed in the leaf and fruit after 0, 1, 3 and 7 days using high performance liquid chromatography. First order degradation kinetics was fitted on this data and degradation rate constants and half life were calculated. Conventional insecticides were found to be more persistent in the crop (Average half life: 1.95, 2.42 and 1.57 days for imidacloprid, endosulfan and profenofos respectively) than bioinsecticides (Average half life 1.25 and 0.27 days for spinosad and biosal respectively). Residues of all tested insecticides were compared with codex and EU MRLs and found both the bio-insecticides treated crops safe for human consumption even after few hours of spray. Endosulfan and profenofos treated crops were not found to be fit for consumption even after 7 days of application. Imidacloprid being biorational (low risk) was also safe for consumption on the next day of application. (author)

Degradation and annealing studies on gamma rays irradiated COTS PPD CISs at different dose rates

International Nuclear Information System (INIS)

Wang, Zujun; Ma, Yingwu; Liu, Jing; Xue, Yuan; He, Baoping; Yao, Zhibin; Huang, Shaoyan; Liu, Minbo; Sheng, Jiangkun

2016-01-01

The degradation and annealing studies on Colbalt-60 gamma-rays irradiated commercial-off-the-shelf (COTS) pinned photodiode (PPD) CMOS image sensors (CISs) at the various dose rates are presented. The irradiation experiments of COTS PPD CISs are carried out at 0.3, 3.0 and 30.0 rad(Si)/s. The COTS PPD CISs are manufactured using a standard 0.18-μm CMOS technology with four-transistor pixel PPD architecture. The behavior of the tested CISs shows a remarkable degradation after irradiation and differs in the dose rates. The dark current, dark signal non-uniformity (DSNU), random noise, saturation output, signal to noise ratio (SNR), and dynamic range (DR) versus the total ionizing dose (TID) at the various dose rates are investigated. The tendency of dark current, DSNU, and random noise increase and saturation output, SNR, and DR to decrease at 3.0 rad(Si)/s are far greater than those at 0.3 and 30.0 rad(Si)/s. The damage mechanisms caused by TID irradiation at the various dose rates are also analyzed. The annealing tests are carried out at room temperature with unbiased conditions after irradiation.

Degradation and annealing studies on gamma rays irradiated COTS PPD CISs at different dose rates

Science.gov (United States)

Wang, Zujun; Ma, Yingwu; Liu, Jing; Xue, Yuan; He, Baoping; Yao, Zhibin; Huang, Shaoyan; Liu, Minbo; Sheng, Jiangkun

2016-06-01

The degradation and annealing studies on Colbalt-60 gamma-rays irradiated commercial-off-the-shelf (COTS) pinned photodiode (PPD) CMOS image sensors (CISs) at the various dose rates are presented. The irradiation experiments of COTS PPD CISs are carried out at 0.3, 3.0 and 30.0 rad(Si)/s. The COTS PPD CISs are manufactured using a standard 0.18-μm CMOS technology with four-transistor pixel PPD architecture. The behavior of the tested CISs shows a remarkable degradation after irradiation and differs in the dose rates. The dark current, dark signal non-uniformity (DSNU), random noise, saturation output, signal to noise ratio (SNR), and dynamic range (DR) versus the total ionizing dose (TID) at the various dose rates are investigated. The tendency of dark current, DSNU, and random noise increase and saturation output, SNR, and DR to decrease at 3.0 rad(Si)/s are far greater than those at 0.3 and 30.0 rad(Si)/s. The damage mechanisms caused by TID irradiation at the various dose rates are also analyzed. The annealing tests are carried out at room temperature with unbiased conditions after irradiation.

Life Insurance Liabilities with Policyholder Behaviour and Stochastic Rates

DEFF Research Database (Denmark)

Buchardt, Kristian

rate, disability rate, and other transition rates are assumed to be deterministic. Broadly speaking this PhD thesis consists of various extensions of this model to address the modern needs of life insurance companies. These extensions can be categorised into two types: the inclusion of policyholder...

Comparative Thermal Degradation Patterns of Natural Yellow Colorants Used in Foods.

Science.gov (United States)

Giménez, Pedro J; Fernández-López, José A; Angosto, José M; Obón, José M

2015-12-01

There is a great interest in natural yellow colorants due to warnings issued about certain yellow food colorings of synthetic origin. However, no comparative studies have been reported of their thermal stability. For this reason, the thermal stabilities of six natural yellow colorants used in foods--lutein, riboflavin, curcumin, ß-carotene, gardenia yellow and Opuntia betaxanthins--were studied in simple solutions over a temperature range 30-90 °C. Spectral properties and visual color were investigated during 6 h of heat treatment. Visual color was monitored from the CIEL*a*b* parameters. The remaining absorbance at maximum wavelength and the total color difference were used to quantify color degradation. The rate of color degradation increased as the temperature rose. The results showed that the thermal degradation of the colorants followed a first-order reaction kinetics. The reaction rate constants and half-life periods were determined as being central to understanding the color degradation kinetics. The temperature-dependent degradation was adequately modeled on the Arrhenius equation. Activation energies ranged from 3.2 kJmol(-1) (lutein) to 43.7 kJmol(-1) (Opuntia betaxanthins). ß-carotene and lutein exhibited high thermal stability, while betaxanthins and riboflavin degraded rapidly as temperature increased. Gardenia yellow and curcumin were in an intermediate position.

Digestion and degradation, air for life

NARCIS (Netherlands)

Lettinga, G.

2001-01-01

Anaerobic degradation of dead biomass is a natural gasification process, an anaerobic crematorium producing a very useful end-product composed of methane and carbon dioxide, generally polluted with small amounts of some malodorous and quite toxic volatile S-compounds. It leads to the production of

Question order sensitivity of subjective well-being measures: focus on life satisfaction, self-rated health, and subjective life expectancy in survey instruments.

Science.gov (United States)

Lee, Sunghee; McClain, Colleen; Webster, Noah; Han, Saram

2016-10-01

This study examines the effect of question context created by order in questionnaires on three subjective well-being measures: life satisfaction, self-rated health, and subjective life expectancy. We conducted two Web survey experiments. The first experiment (n = 648) altered the order of life satisfaction and self-rated health: (1) life satisfaction asked immediately after self-rated health; (2) self-rated health immediately after life satisfaction; and (3) two items placed apart. We examined their correlation coefficient by experimental condition and further examined its interaction with objective health. The second experiment (n = 479) asked life expectancy before and after parental mortality questions. Responses to life expectancy were compared by order using ANOVA, and we examined interaction with parental mortality status using ANCOVA. Additionally, response time and probes were examined. Correlation coefficients between self-rated health and life satisfaction differed significantly by order: 0.313 (life satisfaction first), 0.508 (apart), and 0.643 (self-rated health first). Differences were larger among respondents with chronic conditions. Response times were the shortest when self-rated health was asked first. When life expectancy asked after parental mortality questions, respondents reported considering parents more for answering life expectancy; and respondents with deceased parents reported significantly lower expectancy, but not those whose parents were alive. Question context effects exist. Findings suggest placing life satisfaction and self-rated health apart to avoid artificial attenuation or inflation in their association. Asking about parental mortality prior to life expectancy appears advantageous as this leads respondents to consider parental longevity more, an important factor for true longevity.

Simulating shelf life determination by two simultaneous criteria.

Science.gov (United States)

Peleg, Micha; Normand, Mark D

2015-12-01

The shelf life of food and pharmaceutical products is frequently determined by a marker's concentration or quality index falling below or surpassing an assigned threshold level. Naturally, different chosen markers would indicate different shelf life for the same storage temperature history. We demonstrate that if there are two markers, such as two labile vitamins, the order in which their concentrations cross their respective thresholds may depend not only on their degradation kinetic parameters but also on the particular storage temperature profile, be it isothermal or non-isothermal. Thus, at least theoretically, the order observed in accelerated storage need not be always indicative of the actual order at colder temperatures, except where the two degradation reactions follow the same kinetic order and their temperature-dependence rate parameter is also the same. This is shown with simulated hypothetical degradation reactions that follow first or zero order kinetics and whose rate constant's temperature-dependence obeys the exponential model. It is also demonstrated with simulated hypothetical Maillard reaction's products whose synthesis rather than their degradation follows pseudo zero order kinetics. The software developed to do the simulations and calculate the thresholds crossing points has been posted on the Internet as a freely downloadable interactive Wolfram Demonstration, which can be used as a tool in storage studies and shelf life prediction. In principle, the methodology can be extended from two to any number of markers. Copyright © 2015 Elsevier Ltd. All rights reserved.

Robust PV Degradation Methodology and Application

Energy Technology Data Exchange (ETDEWEB)

Jordan, Dirk [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Deline, Christopher A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kurtz, Sarah [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kimball, Greg [SunPower; Anderson, Mike [SunPower

2017-11-15

The degradation rate plays an important role in predicting and assessing the long-term energy generation of PV systems. Many methods have been proposed for extracting the degradation rate from operational data of PV systems, but most of the published approaches are susceptible to bias due to inverter clipping, module soiling, temporary outages, seasonality, and sensor degradation. In this manuscript, we propose a methodology for determining PV degradation leveraging available modeled clear-sky irradiance data rather than site sensor data, and a robust year-over-year (YOY) rate calculation. We show the method to provide reliable degradation rate estimates even in the case of sensor drift, data shifts, and soiling. Compared with alternate methods, we demonstrate that the proposed method delivers the lowest uncertainty in degradation rate estimates for a fleet of 486 PV systems.

Characterization and degradation potential of diesel-degrading bacterial strains for application in bioremediation.

Science.gov (United States)

Balseiro-Romero, María; Gkorezis, Panagiotis; Kidd, Petra S; Van Hamme, Jonathan; Weyens, Nele; Monterroso, Carmen; Vangronsveld, Jaco

2017-10-03

Bioremediation of polluted soils is a promising technique with low environmental impact, which uses soil organisms to degrade soil contaminants. In this study, 19 bacterial strains isolated from a diesel-contaminated soil were screened for their diesel-degrading potential, biosurfactant (BS) production, and biofilm formation abilities, all desirable characteristics when selecting strains for re-inoculation into hydrocarbon-contaminated soils. Diesel-degradation rates were determined in vitro in minimal medium with diesel as the sole carbon source. The capacity to degrade diesel range organics (DROs) of strains SPG23 (Arthobacter sp.) and PF1 (Acinetobacter oleivorans) reached 17-26% of total DROs after 10 days, and 90% for strain GK2 (Acinetobacter calcoaceticus). The amount and rate of alkane degradation decreased significantly with increasing carbon number for strains SPG23 and PF1. Strain GK2, which produced BSs and biofilms, exhibited a greater extent, and faster rate of alkane degradation compared to SPG23 and PF1. Based on the outcomes of degradation experiments, in addition to BS production, biofilm formation capacities, and previous genome characterizations, strain GK2 is a promising candidate for microbial-assisted phytoremediation of diesel-contaminated soils. These results are of particular interest to select suitable strains for bioremediation, not only presenting high diesel-degradation rates, but also other characteristics which could improve rhizosphere colonization.

Nuclear power plant life management. An overview of identification of key components in relation with degradation mechanism - IAEA guidelines presentation

International Nuclear Information System (INIS)

Bezdikian, Georges

2005-01-01

Nuclear Power Plant (NPP) lifetime has a direct bearing on the cost of the electricity generated from it. The annual unit cost of electricity is dependent upon the operational time, and also annual costs and the capital cost assumptions function of Euros/kw. If the actual NPP lifetime has been underestimated then an economic penalty could be incurred. But the ageing degradation, of nuclear power plants is an important aspect that requires to be addressed to ensure: - that necessary safety margins are maintained throughout service life; - the adequate reliability and therefore the economic viability of older plants is maintained; - that unforeseen an uncontrolled degradation of critical plant components does not foreshorten the plant lifetime. Accommodating the inevitable obsolescence of some components has also to be addressed during plant life. Plant lifetime management requires the identification and life assessment of those components which not only limit the lifetime of the plant but also those which cannot be reasonably replaced. The planned replacement of major or 'key' components needs to be considered - where economic considerations will largely dictate replacement or the alternative strategy of power plant decommissioning. The necessary but timely planning for maintenance and replacements is a necessary consideration so that functions and reliability are maintained. The reasons for the current increasing attention in the area of plant life management are diverse and range from the fact that many of the older plants are approaching for the oldest plants more than 30 years in operation, and for important number of NPPs between 20 and 30 years. The impact of plant life management on the economics of generating electricity is the subject of ongoing studies and it can readily be seen that there can be both savings and additional costs associated with these activities. Not all degradation processes will be of significance in eroding safety margins and there is a

Degradation of chlorpyrifos in tropical rice soils.

Science.gov (United States)

Das, Subhasis; Adhya, Tapan K

2015-04-01

Chlorpyrifos [O,O-diethyl O-(3,5,6-trichloro-2-pyridinol) phosphorothioate] is used worldwide as an agricultural insecticide against a broad spectrum of insect pests of economically important crops including rice, and soil application to control termites. The insecticide mostly undergoes hydrolysis to diethyl thiophosphoric acid (DETP) and 3,5,6-trichloro-2-pyridinol (TCP), and negligible amounts of other intermediate products. In a laboratory-cum-greenhouse study, chlorpyrifos, applied at a rate of 10 mg kg(-1) soil to five tropical rice soils of wide physico-chemical variability, degraded with a half-life ranging from 27.07 to 3.82 days. TCP was the major metabolite under both non-flooded and flooded conditions. Chlorpyrifos degradation had significant negative relationship with electrical conductivity (EC), cation exchange capacity (CEC), clay and sand contents of the soils under non-flooded conditions. Results indicate that degradation of chlorpyrifos was accelerated with increase in its application frequency, across the representative rice soils. Management regimes including moisture content and presence or absence of rice plants also influenced the process. Biotic factors also play an important role in the degradation of chlorpyrifos as demonstrated by its convincing degradation in mineral salts medium inoculated with non-sterile soil suspension. Copyright © 2015 Elsevier Ltd. All rights reserved.

Accelerated degradation of methyl iodide by agrochemicals.

Science.gov (United States)

Zheng, Wei; Papiernik, Sharon K; Guo, Mingxin; Yates, Scott R

2003-01-29

The fumigant methyl iodide (MeI, iodomethane) is considered a promising alternative to methyl bromide (MeBr) for soil-borne pest control in high-cash-value crops. However, the high vapor pressure of MeI results in emissions of a significant proportion of the applied mass into the ambient air, and this may lead to pollution of the environment. Integrating the application of certain agrochemicals with soil fumigation provides a novel approach to reduce excessive fumigant emissions. This study investigated the potential for several agrochemicals that are commonly used in farming operations, including fertilizers and nitrification inhibitors, to transform MeI in aqueous solution. The pseudo-first-order hydrolysis half-life (t(1/2)) of MeI was approximately 108 d, while the transformation of MeI in aqueous solutions containing selected agrochemicals was more rapid, with t(1/2) agrochemicals on the rate of MeI degradation in soil was also determined. Adsorption to soil apparently reduced the availability of some nitrification inhibitors in the soil aqueous phase and lowered the degradation rate in soil. In contrast, addition of the nitrification inhibitors thiourea and allylthiourea to soil significantly accelerated the degradation of MeI, possibly due to soil surface catalysis. The t(1/2) of MeI was 300 h).

Influence of the formation- and passivation rate of boron-oxygen defects for mitigating carrier-induced degradation in silicon within a hydrogen-based model

International Nuclear Information System (INIS)

Hallam, Brett; Abbott, Malcolm; Nampalli, Nitin; Hamer, Phill; Wenham, Stuart

2016-01-01

A three-state model is used to explore the influence of defect formation- and passivation rates of carrier-induced degradation related to boron-oxygen complexes in boron-doped p-type silicon solar cells within a hydrogen-based model. The model highlights that the inability to effectively mitigate carrier-induced degradation at elevated temperatures in previous studies is due to the limited availability of defects for hydrogen passivation, rather than being limited by the defect passivation rate. An acceleration of the defect formation rate is also observed to increase both the effectiveness and speed of carrier-induced degradation mitigation, whereas increases in the passivation rate do not lead to a substantial acceleration of the hydrogen passivation process. For high-throughput mitigation of such carrier-induced degradation on finished solar cell devices, two key factors were found to be required, high-injection conditions (such as by using high intensity illumination) to enable an acceleration of defect formation whilst simultaneously enabling a rapid passivation of the formed defects, and a high temperature to accelerate both defect formation and defect passivation whilst still ensuring an effective mitigation of carrier-induced degradation

Influence of recycling rate increase of aseptic carton for long-life milk on GWP reduction

International Nuclear Information System (INIS)

Mourad, Anna Lucia; Garcia, Eloisa E.C.; Vilela, Gustavo Braz; Von Zuben, Fernando

2008-01-01

Tetra Pak, through intensive cooperation with its supply chain, increased the post-consumer recycling rate of the aseptic packaging for long-life milk in the last 10 years. In continuation of a previous study that presented a superior overall performance in terms of reduction of the consumption of natural resources, air emissions and most of the water emissions, the objective of the present work was to apply life cycle assessment (LCA) to measure the global warming potential (GWP). The system was assessed using as functional unit 1000 liters of milk packaged in Tetra Pak Aseptic containers. The reduction of greenhouse gas emissions was calculated for recycling rates of 2%, 22%, 30%, 40% and 70% of the post-consumer residues in Scenarios I (only cardboard recycling) and II (total aseptic laminate recycling). Scenario I showed a 14% reduction in GWP, representing 26 kg of avoided CO 2 equiv. emitted due to the efforts of Tetra Pak to increase the recycling rate from 2% (2000) to 22% (2004). If it will be possible to increase the recycling rate to 70% of post-consumer packages in the future, a 48% reduction of GWP could be attained. Methane exhibited the greatest mass reduction among the greenhouse emissions, since it is emitted during the production of cardboard and also as a result of anaerobic degradation in landfills. The total reduction of the energy requirements of the system due to the increase of the recycling rate (from 2% to 22%) is 154 MJ/1000 liters, a saving of 7%. Scenario II (which considers additional polyethylene and aluminum recycling) has a smaller effect on GWP reduction than Scenario I, since PE/AL represent only 25% of the total mass of the container. The major benefit of the recycling of aseptic cartons is the reduction of the amounts of virgin materials required and the consequent reduction of air emissions. The results of this study can be used to encourage the collection of post-consumer milk cartons as part of environmental education

The role of interest and inflation rates in life-cycle cost analysis

Science.gov (United States)

Eisenberger, I.; Remer, D. S.; Lorden, G.

1978-01-01

The effect of projected interest and inflation rates on life cycle cost calculations is discussed and a method is proposed for making such calculations which replaces these rates by a single parameter. Besides simplifying the analysis, the method clarifies the roles of these rates. An analysis of historical interest and inflation rates from 1950 to 1976 shows that the proposed method can be expected to yield very good projections of life cycle cost even if the rates themselves fluctuate considerably.

Teardown analysis for detecting shelf-life degradation

Science.gov (United States)

Eckstein, A. S.

1971-01-01

Analysis is guideline in examining component materials, analytically determining physical properties and chemical compositions, and developing control data necessary for ascertaining effects of environments and their influence on deterioration and degradation mechanisms.

Applications and extensions of degradation modeling

International Nuclear Information System (INIS)

Hsu, F.; Subudhi, M.; Samanta, P.K.; Vesely, W.E.

1991-01-01

Component degradation modeling being developed to understand the aging process can have many applications with potential advantages. Previous work has focused on developing the basic concepts and mathematical development of a simple degradation model. Using this simple model, times of degradations and failures occurrences were analyzed for standby components to detect indications of aging and to infer the effectiveness of maintenance in preventing age-related degradations from transforming to failures. Degradation modeling approaches can have broader applications in aging studies and in this paper, we discuss some of the extensions and applications of degradation modeling. The application and extension of degradation modeling approaches, presented in this paper, cover two aspects: (1) application to a continuously operating component, and (2) extension of the approach to analyze degradation-failure rate relationship. The application of the modeling approach to a continuously operating component (namely, air compressors) shows the usefulness of this approach in studying aging effects and the role of maintenance in this type component. In this case, aging effects in air compressors are demonstrated by the increase in both the degradation and failure rate and the faster increase in the failure rate compared to the degradation rate shows the ineffectiveness of the existing maintenance practices. Degradation-failure rate relationship was analyzed using data from residual heat removal system pumps. A simple linear model with a time-lag between these two parameters was studied. The application in this case showed a time-lag of 2 years for degradations to affect failure occurrences. 2 refs

Applications and extensions of degradation modeling

Energy Technology Data Exchange (ETDEWEB)

Hsu, F.; Subudhi, M.; Samanta, P.K. [Brookhaven National Lab., Upton, NY (United States); Vesely, W.E. [Science Applications International Corp., Columbus, OH (United States)

1991-12-31

Component degradation modeling being developed to understand the aging process can have many applications with potential advantages. Previous work has focused on developing the basic concepts and mathematical development of a simple degradation model. Using this simple model, times of degradations and failures occurrences were analyzed for standby components to detect indications of aging and to infer the effectiveness of maintenance in preventing age-related degradations from transforming to failures. Degradation modeling approaches can have broader applications in aging studies and in this paper, we discuss some of the extensions and applications of degradation modeling. The application and extension of degradation modeling approaches, presented in this paper, cover two aspects: (1) application to a continuously operating component, and (2) extension of the approach to analyze degradation-failure rate relationship. The application of the modeling approach to a continuously operating component (namely, air compressors) shows the usefulness of this approach in studying aging effects and the role of maintenance in this type component. In this case, aging effects in air compressors are demonstrated by the increase in both the degradation and failure rate and the faster increase in the failure rate compared to the degradation rate shows the ineffectiveness of the existing maintenance practices. Degradation-failure rate relationship was analyzed using data from residual heat removal system pumps. A simple linear model with a time-lag between these two parameters was studied. The application in this case showed a time-lag of 2 years for degradations to affect failure occurrences. 2 refs.

Applications and extensions of degradation modeling

Energy Technology Data Exchange (ETDEWEB)

Hsu, F.; Subudhi, M.; Samanta, P.K. (Brookhaven National Lab., Upton, NY (United States)); Vesely, W.E. (Science Applications International Corp., Columbus, OH (United States))

1991-01-01

Component degradation modeling being developed to understand the aging process can have many applications with potential advantages. Previous work has focused on developing the basic concepts and mathematical development of a simple degradation model. Using this simple model, times of degradations and failures occurrences were analyzed for standby components to detect indications of aging and to infer the effectiveness of maintenance in preventing age-related degradations from transforming to failures. Degradation modeling approaches can have broader applications in aging studies and in this paper, we discuss some of the extensions and applications of degradation modeling. The application and extension of degradation modeling approaches, presented in this paper, cover two aspects: (1) application to a continuously operating component, and (2) extension of the approach to analyze degradation-failure rate relationship. The application of the modeling approach to a continuously operating component (namely, air compressors) shows the usefulness of this approach in studying aging effects and the role of maintenance in this type component. In this case, aging effects in air compressors are demonstrated by the increase in both the degradation and failure rate and the faster increase in the failure rate compared to the degradation rate shows the ineffectiveness of the existing maintenance practices. Degradation-failure rate relationship was analyzed using data from residual heat removal system pumps. A simple linear model with a time-lag between these two parameters was studied. The application in this case showed a time-lag of 2 years for degradations to affect failure occurrences. 2 refs.

Anthocyanins degradation during storage of Hibiscus sabdariffa extract and evolution of its degradation products.

Science.gov (United States)

Sinela, André; Rawat, Nadirah; Mertz, Christian; Achir, Nawel; Fulcrand, Hélène; Dornier, Manuel

2017-01-01

Degradation parameters of two main anthocyanins from roselle extract (Hibiscus sabdariffa L.) stored at different temperatures (4-37°C) over 60days were determined. Anthocyanins and some of their degradation products were monitored and quantified using HPLC-MS and DAD. Degradation of anthocyanins followed first-order kinetics and reaction rate constants (k values), which were obtained by non-linear regression, showed that the degradation rate of delphinidin 3-O-sambubioside was higher than that of cyanidin 3-O-sambubioside with k values of 9.2·10(-7)s(-1) and 8.4·10(-7)s(-1) at 37°C respectively. The temperature dependence of the rate of anthocyanin degradation was modeled by the Arrhenius equation. Degradation of delphinidin 3-O-sambubioside (Ea=90kJmol(-1)) tended to be significantly more sensitive to an increase in temperature than cyanidin 3-O-sambubioside (Ea=80kJmol(-1)). Degradation of these anthocyanins formed scission products (gallic and protocatechuic acids respectively) and was accompanied by an increase in polymeric color index. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effects of Self-Rated Health and Self-Rated Economic Situation on Depressed Mood Via Life Satisfaction Among Older Adults in Costa Rica

Science.gov (United States)

Reyes Fernández, Benjamín; Rosero-Bixby, Luis; Koivumaa-Honkanen, Heli

2016-01-01

Objective: The study examined the relationship of self-rated health and self-rated economic situation with depressed mood, and life satisfaction as mediator of this relationship among older adults in Costa Rica. Method: A longitudinal study was conducted with a subsample (N = 1,618) from the Costa Rican Longevity and Healthy Aging Study (CRELES). Self-rated health, self-rated economic situation, depressed mood, and life satisfaction were measured at baseline, and depressed mood was reassessed 18 months later. Putative mechanisms for changes in depressed mood were examined by means of conditional process analysis. Results: Self-rated health was negatively associated to depressed mood. This effect took place via life satisfaction. An interaction showed that better economic situation compensated the effect of a low self-rated health on life satisfaction. Discussion: This study suggests that subjective variables such as self-rated health, economic situation, and life satisfaction should be considered when addressing the onset of depressed mood. PMID:26092651

Degradation of methyl tert-butyl ether by gel immobilized Methylibium petroleiphilum PM1.

Science.gov (United States)

Chen, Dongzhi; Chen, Jianmeng; Zhong, Weihong; Cheng, Zhuowei

2008-07-01

Cells of Methylibium petroleiphilum PM1 were immobilized in gel beads to degrade methyl tert-butyl ether (MTBE). Calcium alginate, agar, polyacrylamide and polyvinvyl alcohol were screened as suitable immobilization matrices, with calcium alginate demonstrating the fastest MTBE-degradation rate. The rate was accelerated by 1.8-fold when the beads had been treated in physiological saline for 24h at 28 degrees C. MTBE degradation in mineral salts medium (MSM) was accompanied by the increase of biomass. The half-life of MTBE-degradation activity for the encapsulated cells stored at 28 degrees C was about 120 h, which was obviously longer than that of free cells (approximately 36 h). Efficient reusability of the beads up to 30 batches was achieved in poor nutrition solution as compared to only 6 batches in MSM. The immobilized cells could be operated in a packed-bed reactor for degradation of 10 mg L(-1) MTBE in groundwater with more than 99% removal efficiency at hydraulic retention time of 20 min. These results suggested that immobilized cells of PM1 in bioreactor might be applicable to a groundwater treatment system for the removal of MTBE.

Comparison of oxytetracycline degradation behavior in pig manure with different antibiotic addition methods.

Science.gov (United States)

Wang, Yan; Chen, Guixiu; Liang, Juanboo; Zou, Yongde; Wen, Xin; Liao, Xindi; Wu, Yinbao

2015-12-01

Using manure collected from swine fed with diet containing antibiotics and antibiotic-free swine manure spiked with antibiotics are the two common methods of studying the degradation behavior of veterinary antibiotic in manure in the environment. However, few studies had been conducted to co-compare these two different antibiotic addition methods. This study used oxytetracycline (OTC) as a model antibiotic to study antibiotic degradation behavior in manure under the above two OTC addition methods. In addition, the role of microorganisms present in the manure on degradation behavior was also examined. The results showed that degradation half-life of OTC in manure from swine fed OTC (9.04 days) was significantly shorter than that of the manure directly treated with OTC (9.65 days). Concentration of 4-epi-OTC in manure from swine fed OTC peaked earlier than that in manure spiked with OTC, and the degradation rates of 4-epi-OTC and α-apo-OTC in the manure from swine fed OTC were faster, but the peak concentrations were lower, than those in manure spiked with OTC. Bacterial diversity and relative abundance of Bacillus cereus data demonstrated that sterilization of the manure before experiment significantly decreased OTC degradation rate in both of the addition methods. Results of the present study demonstrated that the presence of the metabolites (especially 4-epi-OTC) and microorganisms had significant influence on OTC degradation.

Optimizing Battery Usage and Management for Long Life

Energy Technology Data Exchange (ETDEWEB)

Smith, Kandler; Shi, Ying; Wood, Eric; Pesaran, Ahmad

2016-06-16

This presentation discusses the impact of system design factors on battery aging and end of life. Topics include sizing of the SOC operating window, cell balancing and thermal management systems and their value in reducing pack degradation rates and cell imbalance growth over lifetime.

Assessment of the degradation efficiency of full-scale biogas plants: A comparative study of degradation indicators.

Science.gov (United States)

Li, Chao; Nges, Ivo Achu; Lu, Wenjing; Wang, Haoyu

2017-11-01

Increasing popularity and applications of the anaerobic digestion (AD) process has necessitated the development and identification of tools for obtaining reliable indicators of organic matter degradation rate and hence evaluate the process efficiency especially in full-scale, commercial biogas plants. In this study, four biogas plants (A1, A2, B and C) based on different feedstock, process configuration, scale and operational performance were selected and investigated. Results showed that the biochemical methane potential (BMP) based degradation rate could be use in incisively gauging process efficiency in lieu of the traditional degradation rate indicators. The BMP degradation rates ranged from 70 to 90% wherein plants A2 and C showed the highest throughput. This study, therefore, corroborates the feasibility of using the BMP degradation rate as a practical tool for evaluating process performance in full-scale biogas processes and spots light on the microbial diversity in full-scale biogas processes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Insulation Resistance Degradation in Ni-BaTiO3 Multilayer Ceramic Capacitors

Science.gov (United States)

Liu, Donhang (David)

2015-01-01

Insulation resistance (IR) degradation in Ni-BaTiO3 multilayer ceramic capacitors has been characterized by the measurement of both time to failure and direct-current (DC) leakage current as a function of stress time under highly accelerated life test conditions. The measured leakage current-time dependence data fit well to an exponential form, and a characteristic growth time ?SD can be determined. A greater value of tau(sub SD) represents a slower IR degradation process. Oxygen vacancy migration and localization at the grain boundary region results in the reduction of the Schottky barrier height and has been found to be the main reason for IR degradation in Ni-BaTiO3 capacitors. The reduction of barrier height as a function of time follows an exponential relation of phi (??)=phi (0)e(exp -2?t), where the degradation rate constant ??=??o??(????/????) is inversely proportional to the mean time to failure (MTTF) and can be determined using an Arrhenius plot. For oxygen vacancy electromigration, a lower barrier height phi(0) will favor a slow IR degradation process, but a lower phi(0) will also promote electronic carrier conduction across the barrier and decrease the insulation resistance. As a result, a moderate barrier height phi(0) (and therefore a moderate IR value) with a longer MTTF (smaller degradation rate constant ??) will result in a minimized IR degradation process and the most improved reliability in Ni-BaTiO3 multilayer ceramic capacitors.

Degradation of copepod fecal pellets

DEFF Research Database (Denmark)

Poulsen, Louise K.; Iversen, Morten

2008-01-01

amount of fecal pellets. The total degradation rate of pellets by the natural plankton community of Oresund followed the phytoplankton biomass, with maximum degradation rate during the spring bloom (2.5 +/- 0.49 d(-1)) and minimum (0.52 +/- 0.14 d(-1)) during late winter. Total pellet removal rate ranged...

Optimizing Battery Usage and Management for Long Life

Energy Technology Data Exchange (ETDEWEB)

Smith, Kandler; Shi, Ying; Wood, Eric; Pesaran, Ahmad

2016-06-16

This presentation discusses the impact of system design factors on battery aging and end of life. Topics include sizing of the state-of-charge operating window, cell balancing, and thermal management systems and their value in reducing pack degradation rates and cell imbalance growth over lifetime.

Purex diluent degradation

International Nuclear Information System (INIS)

Tallent, O.K.; Mailen, J.C.; Pannell, K.D.

1984-02-01

The chemical degradation of normal paraffin hydrocarbon (NPH) diluents both in the pure state and mixed with 30% tributyl phosphate (TBP) was investigated in a series of experiments. The results show that degradation of NPH in the TBP-NPH-HNO 3 system is consistent with the active chemical agent being a radical-like nitrogen dioxide (NO 2 ) molecule, not HNO 3 as such. Spectrophotometric, gas chromatographic, mass spectrographic, and titrimetric methods were used to identify the degradation products, which included alkane nitro and nitrate compounds, alcohols, unsaturated alcohols, nitro alcohols, nitro alkenes, ketones, and carboxylic acids. The degradation rate was found to increase with increases in the HNO 3 concentration and the temperature. The rate was decreased by argon sparging to remove NO 2 and by the addition of butanol, which probably acts as a NO 2 scavenger. 13 references, 11 figures

Life cycle costing with a discount rate

Science.gov (United States)

Posner, E. C.

1978-01-01

This article studies life cycle costing for a capability needed for the indefinite future, and specifically investigates the dependence of optimal policies on the discount rate chosen. The two costs considered are reprocurement cost and maintenance and operations (M and O) cost. The procurement price is assumed known, and the M and O costs are assumed to be a known function, in fact, a non-decreasing function, of the time since last reprocurement. The problem is to choose the optimum reprocurement time so as to minimize the quotient of the total cost over a reprocurement period divided by the period. Or one could assume a discount rate and try to minimize the total discounted costs into the indefinite future. It is shown that the optimum policy in the presence of a small discount rate hardly depends on the discount rate at all, and leads to essentially the same policy as in the case in which discounting is not considered.

Mechanical degradation processes: The Belgian experience

International Nuclear Information System (INIS)

Lafaille, J.P.; Hennart, J.C.

1998-01-01

Design life is merely used in Belgium as a requirement in the 'Design Specification' of some components subjected to known degradation processes, such as stress induced fatigue, embrittlement (irradiation or other), various types of corrosion, wear, erosion, thermal aging (electrical insulation, ...), etc. Design life is in no way directly related to the duration of the plant operation. In that sense design life for the Belgian NPP components includes the values of 20, 30 and 40 years. The oldest plant (20 years design life) has been decommissioned in 1991. The most recent units (40 years design life) have still a good time to go. The intermediate units (30 years design life) started around 1975. Consequently components of these plants need be looked at to determine whether or not deteriorations have occurred. The paper presents the various known mechanical degradation processes and how they affect various components. Emphasis is laid on prevention, mitigation or repair measures that have been or are being taken to avoid that the 'Equipment design life' be the limiting factor in the duration of the plant operation. (author)

Degradation of trichloroethylene (TCE) and polychlorinated biphenyls (PCBs) by Fe and Fe-Pd bimetals in the presence of surfactants and cosolvents

International Nuclear Information System (INIS)

Gu, B.; Liang, L.; West, O.R.; Cameron, P.; Davenport, D.

1997-01-01

Surfactants and cosolvents are being used to enhance the removal of dense non-aqueous phase liquids (DNAPL) such as trichloroethylene (TCE) and polychlorinated biphenyls (PCBS) from contaminated soils. However, the waste surfactant solution containing TCE and PCBs must be treated before it can be disposed. This study evaluated the use of zero-valence iron and palladized iron fillings on the dechlorination of TCE and a PCB congener in a dihexylsulfosuccinate surfactant solution. Batch experimental results indicated that TCE can be rapidly degraded by palladized iron filings with a half-life of 27.4 min. PCB was degraded at a slower rate than TCE with a half-life ranging from 100 min to 500 min as the concentration of surfactant increased. In column flow-through experiments, both TCE and PCBs degrade at an enhanced rate with a half-life about 1.5 and 6 min because of an increased solid to solution ratio in the column than in the batch experiments. Results of this work suggest that Fe-Pd filings may be potentially applicable for ex-situ treatment of TCE and PCBs in the surfactant solutions that are generated during surfactant washing of the contaminated soils

Do neurooncological patients and their significant others agree on quality of life ratings?

Directory of Open Access Journals (Sweden)

Hutterer Markus

2009-10-01

Full Text Available Abstract Introduction Patients suffering from brain tumours often experience a wide range of cognitive impairments that impair their ability to report on their quality of life and symptom burden. The use of proxy ratings by significant others may be a promising alternative to gain information for medical decision making or research purposes, if self-ratings are not obtainable. Our study investigated the agreement of quality of life and symptom ratings by the patient him/herself or by a significant other. Methods Patients with primary brain tumours were recruited at the neurooncological outpatient unit of Innsbruck Medical University. Quality of life self- and proxy-ratings were collected using the EORTC QLQ-C30 and its brain cancer module, the QLQ-BN20. Results Between May 2005 and August 2007, 42 pairs consisting of a patient and his/her significant other were included in the study. Most of the employed quality of life scales showed fairly good agreement between patient- and proxy-ratings (median correlation 0.46. This was especially true for Physical Functioning, Sleeping Disturbances, Appetite Loss, Constipation, Taste Alterations, Visual Disorders, Motor Dysfunction, Communication Deficits, Hair Loss, Itchy Skin, Motor Dysfunction and Hair Loss. Worse rater agreement was found for Social Functioning, Emotional Functioning, Cognitive Functioning, Fatigue, Pain, Dyspnoea and Seizures. Conclusion The assessment of quality of life in brain cancer patients through ratings from their significant others seems to be a feasible strategy to gain information about certain aspects of patient's quality of life and symptom burden, if the patient is not able to provide information himself.

Life Prediction of Large Lithium-Ion Battery Packs with Active and Passive Balancing

Energy Technology Data Exchange (ETDEWEB)

Shi, Ying [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Smith, Kandler A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zane, Regan [Utah State University; Anderson, Dyche [Ford Motor Company

2017-07-03

Lithium-ion battery packs take a major part of large-scale stationary energy storage systems. One challenge in reducing battery pack cost is to reduce pack size without compromising pack service performance and lifespan. Prognostic life model can be a powerful tool to handle the state of health (SOH) estimate and enable active life balancing strategy to reduce cell imbalance and extend pack life. This work proposed a life model using both empirical and physical-based approaches. The life model described the compounding effect of different degradations on the entire cell with an empirical model. Then its lower-level submodels considered the complex physical links between testing statistics (state of charge level, C-rate level, duty cycles, etc.) and the degradation reaction rates with respect to specific aging mechanisms. The hybrid approach made the life model generic, robust and stable regardless of battery chemistry and application usage. The model was validated with a custom pack with both passive and active balancing systems implemented, which created four different aging paths in the pack. The life model successfully captured the aging trajectories of all four paths. The life model prediction errors on capacity fade and resistance growth were within +/-3% and +/-5% of the experiment measurements.

Exploring the mechanical behavior of degrading swine neural tissue at low strain rates via the fractional Zener constitutive model.

Science.gov (United States)

Bentil, Sarah A; Dupaix, Rebecca B

2014-02-01

The ability of the fractional Zener constitutive model to predict the behavior of postmortem swine brain tissue was examined in this work. Understanding tissue behavior attributed to degradation is invaluable in many fields such as the forensic sciences or cases where only cadaveric tissue is available. To understand how material properties change with postmortem age, the fractional Zener model was considered as it includes parameters to describe brain stiffness and also the parameter α, which quantifies the viscoelasticity of a material. The relationship between the viscoelasticity described by α and tissue degradation was examined by fitting the model to data collected in a previous study (Bentil, 2013). This previous study subjected swine neural tissue to in vitro unconfined compression tests using four postmortem age groups (week). All samples were compressed to a strain level of 10% using two compressive rates: 1mm/min and 5mm/min. Statistical analysis was used as a tool to study the influence of the fractional Zener constants on factors such as tissue degradation and compressive rate. Application of the fractional Zener constitutive model to the experimental data showed that swine neural tissue becomes less stiff with increased postmortem age. The fractional Zener model was also able to capture the nonlinear viscoelastic features of the brain tissue at low strain rates. The results showed that the parameter α was better correlated with compressive rate than with postmortem age. © 2013 Published by Elsevier Ltd.

Effect of synchronizing the rate of degradation of dietary energy and nitrogen release on growth performance in Brahman cattle

Directory of Open Access Journals (Sweden)

Virote Pattarajinda

2006-01-01

Full Text Available The objective of this research was to determine the effect of synchronizing the rate of degradation of dietary energy and nitrogen release on growth performance in Brahman beef cattle. Fifteen Brahman cattle, 1.5 years old, with an average initial body weight of 184.8±11.1 kg were assigned to one of three treatments according to a randomized complete block design. Dietary treatments contained 3 levels of synchrony index (0.39, 0.56 and 0.74 that were derived from laboratory chemical composition analysis and degradation kinetics using nylon bag technique. Diets were fed at the rate of 2.5% BW by separate concentrate and roughage. Average daily gain increased linearly (P<0.05 with increase levels of synchrony index in the diets. The digestibility of dry matter, organic matter and neutral detergent fiber increased linearly (P<0.01. The digestibility of acid detergent fiber increased linearly (P<0.05. Ruminal total volatile fatty acids concentration increased linearly (P<0.05 at 6 h post feeding. Higher concentration and fluctuation of ruminal ammonia nitrogen and blood urea nitrogen were observed in animals that received lower synchrony index in their diets. Rumen microbial population tended to increase with diets having higher levels of synchrony index. The results indicated that synchronized rate of dietary energy and nitrogen degradation improved ruminal fermentation and digestibility, thus this increased the growth rate in Brahman cattle fed with ricestraw- based diets.

The Effect of Upscaling and Performance Degradation on Onshore Wind Turbine Lifetime Extension Decision Making

Science.gov (United States)

Rubert, T.; McMillan, D.; Niewczas, P.

2017-11-01

Ever greater rated wind turbine generators (WTGs) are reaching their end of design life in the near future. In addition, first research approaches quantified the impact of long-term performance degradation of WTGs. As a consequence, this work is aimed at discussing and analysing the impact of upscaling and performance degradation on the economics of wind turbine lifetime extension. Findings reveal that the lifetime extension levelised cost of energy (LCOE2) of an 18 MW wind farm comprising of 0.5 MW rated WTGs are within the order of £23.52 per MWh. Alternatively, if the same wind farm consists of fewer 2 or 3 MW WTGs, the LCOE2 reduces to £16.56 or £15.49 per MWh, respectively. Further, findings reveal that an annual performance degradation of 1.6% (0.2%) increases LCOE2 by 34-41% (3.6-4.3%).

Rate of degradation of lambda-cyhalothrin and methomyl in grapes (Vitis vinifera L.).

Science.gov (United States)

Banerjee, Kaushik; Upadhyay, Ajay Kumar; Adsule, Pandurang G; Patil, Sangram H; Oulkar, Dasharath P; Jadhav, Deepak R

2006-10-01

Rates of degradation of lambda-cyhalothrin and methomyl residues in grape are reported. The dissipation behavior of both insecticides followed first-order rate kinetics with similar patterns at standard and double-dose applications. Residues of lambda-cyhalothrin were lost with pre-harvest intervals (PHI) of 12.0-12.5 and 15.0-15.5 days, corresponding to the applications at 25 and 50 g a.i. ha-1, respectively. In the case of methomyl, residues were lost with PHI of 55.0 and 61.0 days, following applications at 1 and 2 kg a.i. ha-1, respectively. The PHI, recommended on the basis of the experimental results, was shown to be effective in minimizing residue load of these insecticides below their maximum residue limits (MRLs) in vineyard samples.

Extensions and applications of degradation modeling

International Nuclear Information System (INIS)

Hsu, F.; Subudhi, M.; Samanta, P.K.; Vesely, W.E.

1991-01-01

Component degradation modeling being developed to understand the aging process can have many applications with potential advantages. Previous work has focused on developing the basic concepts and mathematical development of a simple degradation model. Using this simple model, times of degradations and failures occurrences were analyzed for standby components to detect indications of aging and to infer the effectiveness of maintenance in preventing age-related degradations from transforming to failures. Degradation modeling approaches can have broader applications in aging studies and in this paper, the authors discuss some of the extensions and applications of degradation modeling. The extensions and applications of the degradation modeling approaches discussed are: (a) theoretical developments to study reliability effects of different maintenance strategies and policies, (b) relating aging-failure rate to degradation rate, and (c) application to a continuously operating component

Impact of temperature and substrate concentration on degradation rates of acetate, propionate and hydrogen and their links to microbial community structure.

Science.gov (United States)

Zhao, Jing; Westerholm, Maria; Qiao, Wei; Yin, Dongmin; Bi, Shaojie; Jiang, Mengmeng; Dong, Renjie

2018-05-01

The present study investigates the conversion of acetate, propionate and hydrogen consumption linked to the microbial community structure and related to temperature and substrate concentration. Biogas reactors were continuously fed with coffee powder (20 g-COD/L) or acetate (20, 40, and 60 g-COD/L) and operated for 193 days at 37 °C or 55 °C conditions. Starting HRT was 23 days which was then reduced to 7 days. The kinetics of acetate and propionate degradation and hydrogen consumption rates were measured in batch assays. At HRT 7 days, the degradation rate of propionate was higher in thermophilic batches, while acetate degradation rate was higher at mesophilic conditions. The gaseous hydrogen consumption in acetate reactors increased proportionally with temperature and substrate concentration, while the dissolved hydrogen was not affected. The relative high abundance of hydrogentrophic methanogens indicated that the methanogenesis was directed towards the syntrophic acetate oxidation pathway at high acetate concentration and high temperature. Copyright © 2018 Elsevier Ltd. All rights reserved.

Predicting degradability of organic chemicals

Energy Technology Data Exchange (ETDEWEB)

Finizio, A; Vighi, M [Milan Univ. (Italy). Ist. di Entomologia Agraria

1992-05-01

Degradability, particularly biodegradability, is one of the most important factors governing the persistence of pollutants in the environment and consequently influencing their behavior and toxicity in aquatic and terrestrial ecosystems. The need for reliable persistence data in order to assess the environmental fate and hazard of chemicals by means of predictive approaches, is evident. Biodegradability tests are requested by the EEC directive on new chemicals. Neverthless, degradation tests are not easy to carry out and data on existing chemicals are very scarce. Therefore, assessing the fate of chemicals in the environment from the simple study of their structure would be a useful tool. Rates of degradation are a function of the rates of a series of processes. Correlation between degradation rates and structural parameters are will be facilitated if one of the processes is rate determining. This review is a survey of studies dealing with relationships between structure and biodegradation of organic chemicals, to identify the value and limitations of this approach.

The discount rate and the value of remaining years of life

OpenAIRE

Hartwick, John

2008-01-01

We back out an estimate of a personal discount rate of between 3 and 4 percent for a person with a life expectancy of 74 years who dies at age 30 (or 40) and has a value of statistical life of $6.3 million. Central to these calculations is the series generated by Murphy and Topel of value of life years (the dollar value of consumption plus the dollar value of leisure, with some smoothing for income in retirement). We employ the Makeham "model" of life expectancy in our calculations.

Determination of degradation rates of organic substances in the unsaturated soil zone depending on the grain size fractions of various soil types

Science.gov (United States)

Fichtner, Thomas; Stefan, Catalin; Goersmeyer, Nora

2015-04-01

Rate and extent of the biological degradation of organic substances during transport through the unsaturated soil zone is decisively influenced by the chemical and physical properties of the pollutants such as water solubility, toxicity and molecular structure. Furthermore microbial degradation processes are also influenced by soil-specific properties. An important parameter is the soil grain size distribution on which the pore volume and the pore size depends. Changes lead to changes in air and water circulation as well as preferred flow paths. Transport capacity of water inclusive nutrients is lower in existing bad-drainable fine pores in soils with small grain size fractions than in well-drainable coarse pores in a soil with bigger grain size fractions. Because fine pores are saturated with water for a longer time than the coarse pores and oxygen diffusion in water is ten thousand times slower than in air, oxygen is replenished much slower in soils with small grain size fractions. As a result life and growth conditions of the microorganisms are negatively affected. This leads to less biological activity, restricted degradation/mineralization of pollutants or altered microbial processes. The aim of conducted laboratory column experiments was to study the correlation between the grain size fractions respectively pore sizes, the oxygen content and the biodegradation rate of infiltrated organic substances. Therefore two columns (active + sterile control) were filled with different grain size fractions (0,063-0,125 mm, 0,2-0,63 mm and 1-2 mm) of soils. The sterile soil was inoculated with a defined amount of a special bacteria culture (sphingobium yanoikuae). A solution with organic substances glucose, oxalic acid, sinaphylic alcohol and nutrients was infiltrated from the top in intervals. The degradation of organic substances was controlled by the measurement of dissolved organic carbon in the in- and outflow of the column. The control of different pore volumes

Proceedings of the topical meeting on nuclear power plant life extension

International Nuclear Information System (INIS)

Anon.

1988-01-01

This book contains the proceedings of the topical meeting on nuclear power plant life extension. The sessions are organized under the following headings: Perspectives on nuclear power plant life extension, the potential for additional years of power production, NRC and industry life extension initiatives, concrete and structures degradation and evaluation of useful remaining life, plant life extension programs, Reactor pressure vessel and intervals degradation and evaluation of useful remaining life, life extension decision making issues and institutions, systems degradation and evaluation of remaining life, monitoring and repair, design records and maintenance activities for life extension, Mechanical and electrical component degradation and evaluation of remaining life, expert systems and other techniques for enhanced and continued operation, life extension aspect of codes, standards, and related technologies, piping and valve degradation and evaluation of useful remaining life

Lifestyle-related attitudes: do they explain self-rated health and life-satisfaction?

Science.gov (United States)

Pickard, A Simon; Jalundhwala, Yash J; Bewsher, Helen; Sharp, Lisa K; Walton, Surrey M; Schumock, Glen T; Caskey, Rachel N

2018-05-01

Strategies to improve public health may benefit from targeting specific lifestyles associated with poor health behaviors and outcomes. The aim of this study was to characterize and examine the relationship between health and lifestyle-related attitudes (HLAs) and self-rated health and life-satisfaction. Secondary analyses were conducted on data from a 2012 community wellness survey in Kirklees, UK. Using a validated HLA tool, respondents (n = 9130) were categorized into five segments: health conscious realists (33%), balanced compensators (14%), live-for-todays (18%), hedonistic immortals (10%), and unconfident fatalists (25%). Multivariate regression was used to examine whether HLAs could explain self-rated health using the EQ-5D visual analog scale (EQ-VAS) and life-satisfaction. Health conscious realists served as the reference group. Self-rated health differed by HLA, with adjusted mean EQ-VAS scores being significantly higher (better) among balanced compensators (1.15, 95% CI 0.27, 2.03) and lower scores among unconfident fatalists (- 9.02, 95% CI - 9.85, - 8.21) and live-for-todays (- 1.96, 95% CI - 2.80, - 1.14). Balanced compensators were less likely to report low life-satisfaction (OR 0.75, 95% CI 0.62, 0.90), while unconfident fatalists were most likely to have low life-satisfaction (OR 3.51, 95% CI 2.92, 4.23). Segmentation by HLA explained differences in self-rated health and life-satisfaction, with unconfident fatalists being a distinct segment with significantly worse health perceptions and life-satisfaction. Health promotion efforts may benefit from considering the HLA segment that predominates a patient group, especially unconfident fatalists.

Reaction mechanisms and rate constants of waste degradation in landfill bioreactor systems with enzymatic-enhancement.

Science.gov (United States)

Jayasinghe, P A; Hettiaratchi, J P A; Mehrotra, A K; Kumar, S

2014-06-01

Augmenting leachate before recirculation with peroxidase enzymes is a novel method to increase the available carbon, and therefore the food supply to microorganisms at the declining phase of the anaerobic landfill bioreactor operation. In order to optimize the enzyme-catalyzed leachate recirculation process, it is necessary to identify the reaction mechanisms and determine rate constants. This paper presents a kinetic model developed to ascertain the reaction mechanisms and determine the rate constants for enzyme catalyzed anaerobic waste degradation. The maximum rate of reaction (Vmax) for MnP enzyme-catalyzed reactors was 0.076 g(TOC)/g(DS).day. The catalytic turnover number (k(cat)) of the MnP enzyme-catalyzed was 506.7 per day while the rate constant (k) of the un-catalyzed reaction was 0.012 per day. Copyright © 2014 Elsevier Ltd. All rights reserved.

Degradation Capability of n-hexadecane Degrading Bacteria from Petroleum Contaminated Soils

Directory of Open Access Journals (Sweden)

PENG Huai-li

2017-05-01

Full Text Available Samplings were performed in the petroleum contaminated soils of Dongying, Shandong Province of China. Degrading bacteria was isolated through enrichment in a Bushnel-Hass medium, with n-hexadecane as the sole source of carbon and energy. Then the isolated strains were identified by amplification of 16S rDNA gene and sequencing. The strain TZSX2 was selected as the powerful bacteria with stronger degradation ability, which was then identified as Rhodococcus hoagii genera based on the constructing results of the phylogenetic tree. The optimum temperature that allowed both high growth and efficient degradation ratio was in the scope of 28~36 ℃, and gas chromatography results showed that approximately more than 30% of n-hexadecane could be degraded in one week of incubation within the temperature range. Moreover, the strain TZSX2 was able to grow in high concentrations of n-hexadecane. The degradation rate reached 79% when the initial n-hexadecane concentration was 2 mL·L-1,while it still achieved 12% with n-hexadecane concentration of 20 mL·L-1. The optimal pH was 9 that allowed the highest growth and the greatest degradation rate of 91%. Above all, the screened strain TZSX2 showed high capabilities of alkali tolerance with excellent degradation efficiency for even high concentration of n-hexadecane, and thus it would be quite suitable for the remediation of petroleum contaminated soils especially in the extreme environment.

Degradable polyphosphazene/poly(alpha-hydroxyester) blends: degradation studies.

Science.gov (United States)

Ambrosio, Archel M A; Allcock, Harry R; Katti, Dhirendra S; Laurencin, Cato T

2002-04-01

Biomaterials based on the polymers of lactic acid and glycolic acid and their copolymers are used or studied extensively as implantable devices for drug delivery, tissue engineering and other biomedical applications. Although these polymers have shown good biocompatibility, concerns have been raised regarding their acidic degradation products, which have important implications for long-term implantable systems. Therefore, we have designed a novel biodegradable polyphosphazene/poly(alpha-hydroxyester) blend whose degradation products are less acidic than those of the poly(alpha-hydroxyester) alone. In this study, the degradation characteristics of a blend of poly(lactide-co-glycolide) (50:50 PLAGA) and poly[(50% ethyl glycinato)(50% p-methylphenoxy) phosphazene] (PPHOS-EG50) were qualitatively and quantitatively determined with comparisons made to the parent polymers. Circular matrices (14mm diameter) of the PLAGA, PPHOS-EG50 and PLAGA-PPHOS-EG50 blend were degraded in non-buffered solutions (pH 7.4). The degraded polymers were characterized for percentage mass loss and molecular weight and the degradation medium was characterized for acid released in non-buffered solutions. The amounts of neutralizing base necessary to bring about neutral pH were measured for each polymer or polymer blend during degradation. The poly(phosphazene)/poly(lactide-co-glycolide) blend required significantly less neutralizing base in order to bring about neutral solution pH during the degradation period studied. The results indicated that the blend degraded at a rate intermediate to that of the parent polymers and that the degradation products of the polyphosphazene neutralized the acidic degradation products of PLAGA. Thus, results from these in vitro degradation studies suggest that the PLAGA-PPHOS-EG50 blend may provide a viable improvement to biomaterials based on acid-releasing organic polymers.

Study on Thermal Degradation Characteristics and Regression Rate Measurement of Paraffin-Based Fuel

Directory of Open Access Journals (Sweden)

Songqi Hu

2015-09-01

Full Text Available Paraffin fuel has been found to have a regression rate that is higher than conventional HTPB (hydroxyl-terminated polybutadiene fuel and, thus, presents itself as an ideal energy source for a hybrid rocket engine. The energy characteristics of paraffin-based fuel and HTPB fuel have been calculated by the method of minimum free energy. The thermal degradation characteristics were measured for paraffin, pretreated paraffin, HTPB and paraffin-based fuel in different working conditions by the using differential scanning calorimetry (DSC and a thermogravimetric analyzer (TGA. The regression rates of paraffin-based fuel and HTPB fuel were tested by a rectangular solid-gas hybrid engine. The research findings showed that: the specific impulse of paraffin-based fuel is almost the same as that of HTPB fuel; the decomposition temperature of pretreated paraffin is higher than that of the unprocessed paraffin, but lower than that of HTPB; with the increase of paraffin, the initial reaction exothermic peak of paraffin-based fuel is reached in advance, and the initial reaction heat release also increases; the regression rate of paraffin-based fuel is higher than the common HTPB fuel under the same conditions; with the increase of oxidizer mass flow rate, the regression rate of solid fuel increases accordingly for the same fuel formulation.

Use of sunlight to degrade oxytetracycline in marine aquaculture's waters

International Nuclear Information System (INIS)

Leal, J.F.; Esteves, V.I.; Santos, E.B.H.

2016-01-01

Oxytracycline (OTC) is a broad spectrum antibiotic authorized for use in European aquaculture. Its photo-degradation has been widely studied in synthetic aqueous solutions, sometimes resorting to expensive methods and without proven effectiveness in natural waters. Thus, this work studied the possibility to apply the solar photo-degradation for removal of OTC from marine aquaculture's waters. For that, water samples were collected at different locals of the water treatment circuit, from two different aquaculture companies. Water samples were firstly characterized regarding to pH, salinity, total suspended solids (TSS), organic carbon and UV–Vis spectroscopic characteristics. Then, the samples were spiked with OTC and irradiated using simulated sunlight in order to evaluate the matrix effects on OTC photo-degradation. From kinetic results, the apparent quantum yields and the outdoor half-life times, at 40°N for midsummer and midwinter days were estimated by the first time for these conditions. For a midsummer day, at sea level, the outdoor half-life time predicted for OTC in these aquaculture's waters ranged between 21 and 25 min. Additionally, the pH and salinity effects on the OTC photo-degradation were evaluated and it has been shown that high pH values and the presence of sea salt increase the OTC photo-degradation rate in aquaculture's waters, compared to results in deionised water. The results are very promising to apply this low-cost methodology using the natural sunlight in aquaculture's waters to remove OTC. - Highlights: • Oxytetracycline (OTC) is one of the most used antibiotics in aquaculture. • OTC photolysis in marine aquaculture's water is faster than in deionised water. • The sunlight radiation quickly remove the OTC from aquaculture's water. • Outdoor half-life for a midsummer day is 21–25 min in aquaculture's water. • High pH's and salinities increase the OTC photo-degradation. - This work

Cellular Metabolic Rate Is Influenced by Life-History Traits in Tropical and Temperate Birds

OpenAIRE

Jimenez, Ana Gabriela; Van Brocklyn, James; Wortman, Matthew; Williams, Joseph B.

2014-01-01

In general, tropical birds have a "slow pace of life," lower rates of whole-animal metabolism and higher survival rates, than temperate species. A fundamental challenge facing physiological ecologists is the understanding of how variation in life-history at the whole-organism level might be linked to cellular function. Because tropical birds have lower rates of whole-animal metabolism, we hypothesized that cells from tropical species would also have lower rates of cellular metabolism than cel...

Degradation of alachlor in aqueous solution by using hydrodynamic cavitation.

Science.gov (United States)

Wang, Xikui; Zhang, Yong

2009-01-15

The degradation of alachlor aqueous solution by using hydrodynamic cavitation was systematically investigated. It was found that alachlor in aqueous solution can be deomposed with swirling jet-induced cavitation. The degradation can be described by a pseudo-first-order kinetics and the degradation rate was found to be 4.90x10(-2)min(-1). The effects of operating parameters such as fluid pressure, solution temperature, initial concentration of alachlor and medium pH on the degradation rates of alachlor were also discussed. The results showed that the degradation rates of alachlor increased with increasing pressure and decreased with increasing initial concentration. An optimum temperature of 40 degrees C existed for the degradation rate of alachlor and the degradation rate was also found to be slightly depend on medium pH. Many degradation products formed during the process, and some of them were qualitatively identified by GC-MS.

Thermal degradation of deoxynivalenol during maize bread baking.

Science.gov (United States)

Numanoglu, E; Gökmen, V; Uygun, U; Koksel, H

2012-01-01

The thermal degradation of deoxynivalenol (DON) was determined at isothermal baking conditions within the temperature range of 100-250°C, using a crust-like model, which was prepared with naturally contaminated maize flour. No degradation was observed at 100°C. For the temperatures of 150, 200 and 250°C, thermal degradation rate constants (k) were calculated and temperature dependence of DON degradation was observed by using Arrhenius equation. The degradation of DON obeyed Arrhenius law with a regression coefficient of 0.95. A classical bread baking operation was also performed at 250°C for 70 min and the rate of DON degradation in the bread was estimated by using the kinetic data derived from the model study. The crust and crumb temperatures recorded during bread baking were used to calculate the thermal degradation rate constants (k) and partial DON degradations at certain time intervals. Using these data, total degradation at the end of the entire baking process was predicted for both crust and crumb. This DON degradation was consistent with the experimental degradation data, confirming the accuracy of kinetic constants determined by means of the crust-like model.

Benthic life in the pelagic: Aggregate encounter and degradation rates by pelagic harpacticoid copepods

DEFF Research Database (Denmark)

Koski, Marja; Kiørboe, Thomas; Takahashi, K.

2005-01-01

We measured field abundances, feeding rates, swimming behavior, and particle colonization of two harpacticoids, the pelagic Microsetella norvegica and the semibenthic Amonardia normanni, to examine (1) if aggregates have a significant role in harpacticoid nutrition and (2) if harpacticoids...

Degradation of N-nitrosodimethylamine (NDMA) in landscape soils.

Science.gov (United States)

Yang, W C; Gan, J; Liu, W P; Green, R

2005-01-01

N-nitrosodimethylamine (NDMA), a potential carcinogen, was commonly found in treated wastewater as a by-product of chlorination. As treated water is increasingly used for landscape irrigation, there is an imperative need to understand the leaching risk for NDMA in landscape soils. In this study, adsorption and incubation experiments were conducted using landscape soils planted with turfgrass, ground cover, and trees. Adsorption of NDMA was negligibly weak (K(d) NDMA has a high potential for moving with percolating water in these soils. Degradation of NDMA occurred at different rates among these soils. At 21 degrees C, the half-life (t(1/2)) of NDMA was 4.1 d for the ground cover soil, 5.6 d for the turfgrass soil, and 22.5 d for the tree soil. The persistence was substantially prolonged after autoclaving or when incubated at 10 degrees C. The rate of degradation was not significantly affected by the initial NDMA concentration or addition of organic and inorganic nutrient sources. The relative persistence was inversely correlated with soil organic matter content, soil microbial biomass, and soil dehydrogenase activity, suggesting the importance of microorganisms in NDMA degradation in these soils. These results suggest that the behavior of NDMA depends closely on the vegetation cover in a landscape system, and prolonged persistence and increased leaching may be expected in soils with sparse vegetation due to low organic matter content and limited microbial activity.

Degradation of Insecticides in Poultry Manure: Determining the Insecticidal Treatment Interval for Managing House Fly (Diptera: Muscidae) Populations in Poultry Farms.

Science.gov (United States)

Ong, Song-Quan; Ab Majid, Abdul Hafiz; Ahmad, Hamdan

2016-04-01

It is crucial to understand the degradation pattern of insecticides when designing a sustainable control program for the house fly, Musca domestica (L.), on poultry farms. The aim of this study was to determine the half-life and degradation rates of cyromazine, chlorpyrifos, and cypermethrin by spiking these insecticides into poultry manure, and then quantitatively analyzing the insecticide residue using ultra-performance liquid chromatography. The insecticides were later tested in the field in order to study the appropriate insecticidal treatment intervals. Bio-assays on manure samples were later tested at 3, 7, 10, and 15 d for bio-efficacy on susceptible house fly larvae. Degradation analysis demonstrated that cyromazine has the shortest half-life (3.01 d) compared with chlorpyrifos (4.36 d) and cypermethrin (3.75 d). Cyromazine also had a significantly greater degradation rate compared with chlorpyrifos and cypermethrin. For the field insecticidal treatment interval study, 10 d was the interval that had been determined for cyromazine due to its significantly lower residue; for ChCy (a mixture of chlorpyrifos and cypermethrin), the suggested interval was 7 d. Future work should focus on the effects of insecticide metabolites on targeted pests and the poultry manure environment.

Does adversity early in life affect general population suicide rates? a cross-national study

OpenAIRE

Ritesh Bhandarkar; Ajit Shah

2011-01-01

Abstract: Background: Adversity early in life has been suggested as a protective factor for elderly suicides. However, studies examining this relationship in general population suicide rates are scarce. Methods: The relationship between general population suicide rates and four proxy measures of adversity earlier in life was examined using data from the World Health Organization and the United Nations data banks. Results: General population suicide rates were negatively correlated with the pe...

Effect of electrodeposition current density on the microstructure and the degradation of electroformed iron for degradable stents

Energy Technology Data Exchange (ETDEWEB)

Moravej, Maryam [Laboratory for Biomaterials and Bioengineering, Department of Mining, Metallurgy and Materials Engineering and University Hospital Research Center, Universite Laval, Quebec City, Que. G1V 0A6 (Canada); Department of Mining, Metallurgy and Materials Engineering, Pavillon Adrien-Pouliot, 1065 avenue de la Medecine, Local 1745-E, Universite Laval, Quebec City, Que. G1V 0A6 (Canada); Amira, Sofiene [Aluminium Technology Centre, Industrial Materials Institute, National Research Council Canada, 501, boul. de l' Universite Est, Saguenay, Que. G7H 8C3 (Canada); Prima, Frederic [Laboratory for Physical Metallurgy, Ecole Nationale Superieure de Chimie de Paris, Universite Pierre et Marie Curie, Paris 6 (France); Rahem, Ahmed [Aluminium Technology Centre, Industrial Materials Institute, National Research Council Canada, 501, boul. de l' Universite Est, Saguenay, Que. G7H 8C3 (Canada); Fiset, Michel [Department of Mining, Metallurgy and Materials Engineering, Pavillon Adrien-Pouliot, 1065 avenue de la Medecine, Local 1745-E, Universite Laval, Quebec City, Que. G1V 0A6 (Canada); and others

2011-12-15

Pure iron has become one of the most interesting candidate materials for degradable metallic stents due to its high mechanical properties and moderate degradation. In this work we studied the effect of electrodeposition current density on microstructure and degradation of pure iron films electrodeposited on Ti alloy substrate for degradable metallic stent application. Iron sheets were produced by electrodeposition using four different current densities 1, 2, 5 and 10 A dm{sup -2}. The films were then studied by SEM (scanning electron microscope) and EBSD (electron backscatter diffraction) to observe the surface morphology, grain size and orientation. Potentiodynamic polarization and static immersion tests were used to determine the corrosion rate and to study the degradation behavior of iron films, respectively. The current density was found to significantly influence the texture, the grain size and the grain shape of the electrodeposited iron. At current densities of 1, 5 and 10 A dm{sup -2}, weak textures corresponding to Left-Pointing-Angle-Bracket 1 0 1 Right-Pointing-Angle-Bracket , Left-Pointing-Angle-Bracket 1 1 1 Right-Pointing-Angle-Bracket and Left-Pointing-Angle-Bracket 1 1 2 Right-Pointing-Angle-Bracket in the normal (electrodeposition) direction were obtained, respectively. At these current densities, average grain sizes smaller than 3 {mu}m were also obtained. However, at 2 A dm{sup -2}, a strong Left-Pointing-Angle-Bracket 1 1 1 Right-Pointing-Angle-Bracket //ND texture with density of 7.4 MUD was obtained with larger average grain size of 4.4 {mu}m. The microstructure of iron samples changed after annealing at 550 Degree-Sign C because of the induced recrystallization. Different corrosion rates were obtained from potentiodynamic polarization curves of iron films deposited at different current densities because of their microstructures. Fe-2 showed the lowest corrosion rate due to its larger grains size and its texture. The corrosion rates of all

The rate-size trade-off structures intraspecific variation in Daphnia ambigua life history parameters.

Science.gov (United States)

DeLong, John P; Hanley, Torrance C

2013-01-01

The identification of trade-offs is necessary for understanding the evolution and maintenance of diversity. Here we employ the supply-demand (SD) body size optimization model to predict a trade-off between asymptotic body size and growth rate. We use the SD model to quantitatively predict the slope of the relationship between asymptotic body size and growth rate under high and low food regimes and then test the predictions against observations for Daphnia ambigua. Close quantitative agreement between observed and predicted slopes at both food levels lends support to the model and confirms that a 'rate-size' trade-off structures life history variation in this population. In contrast to classic life history expectations, growth and reproduction were positively correlated after controlling for the rate-size trade-off. We included 12 Daphnia clones in our study, but clone identity explained only some of the variation in life history traits. We also tested the hypothesis that growth rate would be positively related to intergenic spacer length (i.e. the growth rate hypothesis) across clones, but we found that clones with intermediate intergenic spacer lengths had larger asymptotic sizes and slower growth rates. Our results strongly support a resource-based optimization of body size following the SD model. Furthermore, because some resource allocation decisions necessarily precede others, understanding interdependent life history traits may require a more nested approach.

The rate-size trade-off structures intraspecific variation in Daphnia ambigua life history parameters.

Directory of Open Access Journals (Sweden)

John P DeLong

Full Text Available The identification of trade-offs is necessary for understanding the evolution and maintenance of diversity. Here we employ the supply-demand (SD body size optimization model to predict a trade-off between asymptotic body size and growth rate. We use the SD model to quantitatively predict the slope of the relationship between asymptotic body size and growth rate under high and low food regimes and then test the predictions against observations for Daphnia ambigua. Close quantitative agreement between observed and predicted slopes at both food levels lends support to the model and confirms that a 'rate-size' trade-off structures life history variation in this population. In contrast to classic life history expectations, growth and reproduction were positively correlated after controlling for the rate-size trade-off. We included 12 Daphnia clones in our study, but clone identity explained only some of the variation in life history traits. We also tested the hypothesis that growth rate would be positively related to intergenic spacer length (i.e. the growth rate hypothesis across clones, but we found that clones with intermediate intergenic spacer lengths had larger asymptotic sizes and slower growth rates. Our results strongly support a resource-based optimization of body size following the SD model. Furthermore, because some resource allocation decisions necessarily precede others, understanding interdependent life history traits may require a more nested approach.

Degradation of Alloy 800 steam generator tubing and its long-term behaviour predictions for plant life management

International Nuclear Information System (INIS)

Lu, Y.C.; Tapping, R.L.; Pandey, M.D.

2009-01-01

results imply that Alloy 800 SG tubing may experience measurable aging after many years of service. Although these preliminary results require further confirmation, special attention should be paid to manage the SG tubing degradation in a proactive and predictable manner. Electric Power Research Institute (EPRI) and Dominion Engineering, Inc. (DEI) have developed probabilistic approaches using a degradation free lifetime Weibull distribution based on the OPEX of Alloy 600 SG tubing and a concept of materials improvement factors (MIFs) to 'predict' the long-term service behaviour of other SG tubing. In this paper, a new concept, 'corrosion stress cycle analysis' (CSCA) based on the concept of 'Fatigue Usage Factor' used in mechanical design, is proposed here as a guide for predictive and proactive SG life management. The CSCA approach assumes that an alloy can tolerate a certain number of corrosion stress cycles, i.e., excursions due to off-specification (assuming that the specifications are appropriate) chemistry conditions and SG transients etc. Using the in-service experience, the number of stress cycles that occurred in the history of a SG and in the future can be estimated and the Alloy 800 SG tubing long-term degradation can then be predicted. (author)

Complex degradation processes lead to non-exponential decay patterns and age-dependent decay rates of messenger RNA.

Directory of Open Access Journals (Sweden)

Carlus Deneke

Full Text Available Experimental studies on mRNA stability have established several, qualitatively distinct decay patterns for the amount of mRNA within the living cell. Furthermore, a variety of different and complex biochemical pathways for mRNA degradation have been identified. The central aim of this paper is to bring together both the experimental evidence about the decay patterns and the biochemical knowledge about the multi-step nature of mRNA degradation in a coherent mathematical theory. We first introduce a mathematical relationship between the mRNA decay pattern and the lifetime distribution of individual mRNA molecules. This relationship reveals that the mRNA decay patterns at steady state expression level must obey a general convexity condition, which applies to any degradation mechanism. Next, we develop a theory, formulated as a Markov chain model, that recapitulates some aspects of the multi-step nature of mRNA degradation. We apply our theory to experimental data for yeast and explicitly derive the lifetime distribution of the corresponding mRNAs. Thereby, we show how to extract single-molecule properties of an mRNA, such as the age-dependent decay rate and the residual lifetime. Finally, we analyze the decay patterns of the whole translatome of yeast cells and show that yeast mRNAs can be grouped into three broad classes that exhibit three distinct decay patterns. This paper provides both a method to accurately analyze non-exponential mRNA decay patterns and a tool to validate different models of degradation using decay data.

Road Traffic Accident Rate as an Indicator of the Quality of Life

Directory of Open Access Journals (Sweden)

Artur Igorevich Petrov

2016-07-01

Full Text Available The paper considers the issues devoted to assessing the connection between the quality of life and road traffic accident rate in different countries. The hypothesis put forward in the paper is based on the idea that the organization and functioning of the state road traffic safety management system and the outcome characteristics of road traffic accident rate in the road complex are closely related and are derived from the level of development of non-governmental institutions in a particular country. In order to determine how true this hypothesis is, the author carried out statistical studies of the relations between the estimates of the Quality of Life presented for 60 countries in the US News & World Report and the Human Risk indicators estimated for these countries. This indicator proposed by R. Smeed in 1949 for assessing the state of affairs in the field of road safety allows us to evaluate adequately the position of countries in the world ranking of road traffic accident rate. The research aims to establish a regularity that identifies the statistical relationship between the characteristics of the quality of life and human risk (by R. Smeed. The method of construction of correlation-regression models of the processes under consideration is used to achieve this goal. It has been established that there exists a noticeable inverse statistical relationship between the variables of the Quality of Life in different countries (according to the US News & World Report and Human Risk (according to the World Health Organization. The paper discusses reasons for a decline in road traffic accident rate when the quality of life becomes better. The main conclusion of the study lies in the understanding that there exists a strong cause and effect relationship between the level of development of social institutions and the level of transport culture of the population; this relationship is implemented in the form of specific cases of transport

A Comparative Analysis of 2-(Thiocyanomethylthio-Benzothiazole Degradation Using Electro-Fenton and Anodic Oxidation on a Boron-Doped Diamond Electrode

Directory of Open Access Journals (Sweden)

Armando Vázquez

2018-01-01

Full Text Available 2-(Thiocyanomethylthio-benzothiazole (TCMTB is used as fungicide in the paper, tannery, paint, and coatings industries, and its study is important as it is considered toxic to aquatic life. In this study, a comparison of direct anodic oxidation (AO using a boron-doped diamond electrode (BDD and electro-Fenton (EF processes for TCMTB degradation in acidic chloride and sulfate media using a FM01-LC reactor was performed. The results of the electrolysis processes studied in the FM01-LC reactor showed a higher degradation of TCMTB with the anodic oxidation process than with the electro-Fenton process, reaching 81% degradation for the former process versus 47% degradation for the latter process. This difference was attributed to the decrease in H2O2 during the EF process, due to parallel oxidation of chlorides. The degradation rate and current efficiency increased as a function of volumetric flow rate, indicating that convection promotes anodic oxidation and electro-Fenton processes. The results showed that both AO and EF processes could be useful strategies for TCMTB toxicity reduction in wastewaters.

Phosphate conversion coating reduces the degradation rate and suppresses side effects of metallic magnesium implants in an animal model.

Science.gov (United States)

Rahim, Muhammad Imran; Tavares, Ana; Evertz, Florian; Kieke, Marc; Seitz, Jan-Marten; Eifler, Rainer; Weizbauer, Andreas; Willbold, Elmar; Jürgen Maier, Hans; Glasmacher, Birgit; Behrens, Peter; Hauser, Hansjörg; Mueller, Peter P

2017-08-01

Magnesium alloys have promising mechanical and biological properties for the development of degradable implants. However, rapid implant corrosion and gas accumulations in tissue impede clinical applications. With time, the implant degradation rate is reduced by a highly biocompatible, phosphate-containing corrosion layer. To circumvent initial side effects after implantation it was attempted to develop a simple in vitro procedure to generate a similarly protective phosphate corrosion layer. To this end magnesium samples were pre-incubated in phosphate solutions. The resulting coating was well adherent during routine handling procedures. It completely suppressed the initial burst of corrosion and it reduced the average in vitro magnesium degradation rate over 56 days almost two-fold. In a small animal model phosphate coatings on magnesium implants were highly biocompatible and abrogated the appearance of gas cavities in the tissue. After implantation, the phosphate coating was replaced by a layer with an elemental composition that was highly similar to the corrosion layer that had formed on plain magnesium implants. The data demonstrate that a simple pre-treatment could improve clinically relevant properties of magnesium-based implants. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1622-1635, 2017. © 2016 Wiley Periodicals, Inc.

Degradation kinetics of a potent antifouling agent, butenolide, under various environmental conditions

KAUST Repository

Chen, Lianguo

2015-01-01

© 2014 Elsevier Ltd. Here, we investigated the degradation kinetics of butenolide, a promising antifouling compound, under various environmental conditions. The active ingredient of the commercial antifoulant SeaNine 211, 4,5-dichloro-2-n-octyl-4-isothiazolin-3-one (DCOIT), was used as positive control. The results showed that the degradation rate increased with increasing temperature. Half-lives of butenolide at 4. °C, 25. °C and 40. °C were. >64. d, 30.5. d and 3.9. d, respectively. Similar half-lives were recorded for DCOIT: >64. d at 4. °C, 27.9. d at 25. °C and 4.5. d at 40. °C. Exposure to sunlight accelerated the degradation of both butenolide and DCOIT. The photolysis half-lives of butenolide and DCOIT were 5.7. d and 6.8. d, respectively, compared with 9.7. d and 14.4. d for the dark control. Biodegradation led to the fastest rate of butenolide removal from natural seawater, with a half-life of 0.5. d, while no obvious degradation was observed for DCOIT after incubation for 4. d. The biodegradative ability of natural seawater for butenolide was attributed mainly to marine bacteria. During the degradation of butenolide and DCOIT, a gradual decrease in antifouling activity was observed, as indicated by the increased settlement percentage of cypris larvae from barnacle Balanus amphitrite. Besides, increased cell growth of marine diatom Skeletonema costatum demonstrated that the toxicity of seawater decreased gradually without generation of more toxic by-products. Overall, rapid degradation of butenolide in natural seawater supported its claim as a promising candidate for commercial antifouling industry.

Assessment of lumen degradation and remaining useful life of LEDs using particle filter

Energy Technology Data Exchange (ETDEWEB)

Lall, Pradeep [Auburn Univ., AL (United States); Zhang, Hao [Auburn Univ., AL (United States); Davis, Lynn [Auburn Univ., AL (United States)

2013-07-16

With the development of light-emitting diode (LED) technology, light emitting diodes system is becoming a popular light source in daily life and industry area. It has shown that Led from same factory and work under same working condition, may have significantly different behavior. Therefore, it is very important to learn the fail mechanisms, especially in the case of safety critical and harsh environment application. This paper focus on a prognostic health management (PHM) method based on the measurement of forward voltage and forward current of bare LED under harsh environment. In this paper, experiment has been done with ten samples. Ten pristine bare LEDs have been tested at 85°C while simultaneously being subjected to 85% humid environment. Pulse width modulation (PWM) control method has been employed to drive the bare LED in order to reduce the heat effect caused by forward current and high frequency (300HZ) data acquisition has been used to measure the peak forward voltage and forward current. Test to failure (lumen drops to 70 percent) data has been measured to study the effects of high temperature and humid environment loadings on the bare LED. Also, solid state cooling method with peltier cooler has been used to control the temperature of LED in the integrating sphere when take the measurement of lumen flux. The shift of forward voltage forward current curve and lumen degradation has been recorded to help build the fail model and predicted the remaining useful life. In this method, particle filter has been employed to predict the remaining useful life (RUL) of the bare LED and give us a whole picture how Led system fails. Result shows that predication of remaining useful life of Led, made by the particle filter model works under reasonable limit, and hence this method can be employed to predict the failure of Led caused by thermal and humid stress under harsh environment.

Modelling accelerated degradation data using Wiener diffusion with a time scale transformation.

Science.gov (United States)

Whitmore, G A; Schenkelberg, F

1997-01-01

Engineering degradation tests allow industry to assess the potential life span of long-life products that do not fail readily under accelerated conditions in life tests. A general statistical model is presented here for performance degradation of an item of equipment. The degradation process in the model is taken to be a Wiener diffusion process with a time scale transformation. The model incorporates Arrhenius extrapolation for high stress testing. The lifetime of an item is defined as the time until performance deteriorates to a specified failure threshold. The model can be used to predict the lifetime of an item or the extent of degradation of an item at a specified future time. Inference methods for the model parameters, based on accelerated degradation test data, are presented. The model and inference methods are illustrated with a case application involving self-regulating heating cables. The paper also discusses a number of practical issues encountered in applications.

Soil bacteria showing a potential of chlorpyrifos degradation and plant growth enhancement

Directory of Open Access Journals (Sweden)

Shamsa Akbar

Full Text Available ABSTRACT Background: Since 1960s, the organophosphate pesticide chlorpyrifos has been widely used for the purpose of pest control. However, given its persistence and toxicity towards life forms, the elimination of chlorpyrifos from contaminated sites has become an urgent issue. For this process bioremediation is the method of choice. Results: Two bacterial strains, JCp4 and FCp1, exhibiting chlorpyrifos-degradation potential were isolated from pesticide contaminated agricultural fields. These isolates were able to degrade 84.4% and 78.6% of the initial concentration of chlorpyrifos (100 mg L-1 within a period of only 10 days. Based on 16S rRNA sequence analysis, these strains were identified as Achromobacter xylosoxidans (JCp4 and Ochrobactrum sp. (FCp1. These strains exhibited the ability to degrade chlorpyrifos in sterilized as well as non-sterilized soils, and were able to degrade 93-100% of the input concentration (200 mg kg-1 within 42 days. The rate of degradation in inoculated soils ranged from 4.40 to 4.76 mg-1 kg-1 d-1 with rate constants varying between 0.047 and 0.069 d-1. These strains also displayed substantial plant growth promoting traits such as phosphate solubilization, indole acetic acid production and ammonia production both in absence as well as in the presence of chlorpyrifos. However, presence of chlorpyrifos (100 and 200 mg L-1 was found to have a negative effect on indole acetic acid production and phosphate solubilization with percentage reduction values ranging between 2.65-10.6% and 4.5-17.6%, respectively. Plant growth experiment demonstrated that chlorpyrifos has a negative effect on plant growth and causes a decrease in parameters such as percentage germination, plant height and biomass. Inoculation of soil with chlorpyrifos-degrading strains was found to enhance plant growth significantly in terms of plant length and weight. Moreover, it was noted that these strains degraded chlorpyrifos at an increased rate (5

Soil bacteria showing a potential of chlorpyrifos degradation and plant growth enhancement.

Science.gov (United States)

Akbar, Shamsa; Sultan, Sikander

2016-01-01

Since 1960s, the organophosphate pesticide chlorpyrifos has been widely used for the purpose of pest control. However, given its persistence and toxicity towards life forms, the elimination of chlorpyrifos from contaminated sites has become an urgent issue. For this process bioremediation is the method of choice. Two bacterial strains, JCp4 and FCp1, exhibiting chlorpyrifos-degradation potential were isolated from pesticide contaminated agricultural fields. These isolates were able to degrade 84.4% and 78.6% of the initial concentration of chlorpyrifos (100mgL(-1)) within a period of only 10 days. Based on 16S rRNA sequence analysis, these strains were identified as Achromobacter xylosoxidans (JCp4) and Ochrobactrum sp. (FCp1). These strains exhibited the ability to degrade chlorpyrifos in sterilized as well as non-sterilized soils, and were able to degrade 93-100% of the input concentration (200mgkg(-1)) within 42 days. The rate of degradation in inoculated soils ranged from 4.40 to 4.76mg(-1)kg(-1)d(-1) with rate constants varying between 0.047 and 0.069d(-1). These strains also displayed substantial plant growth promoting traits such as phosphate solubilization, indole acetic acid production and ammonia production both in absence as well as in the presence of chlorpyrifos. However, presence of chlorpyrifos (100 and 200mgL(-1)) was found to have a negative effect on indole acetic acid production and phosphate solubilization with percentage reduction values ranging between 2.65-10.6% and 4.5-17.6%, respectively. Plant growth experiment demonstrated that chlorpyrifos has a negative effect on plant growth and causes a decrease in parameters such as percentage germination, plant height and biomass. Inoculation of soil with chlorpyrifos-degrading strains was found to enhance plant growth significantly in terms of plant length and weight. Moreover, it was noted that these strains degraded chlorpyrifos at an increased rate (5.69mg(-1)kg(-1)d(-1)) in planted soil. The

Constitutive and ligand-induced TCR degradation

DEFF Research Database (Denmark)

von Essen, Marina; Bonefeld, Charlotte Menné; Siersma, Volkert

2004-01-01

Modulation of TCR expression levels is a central event during T cell development and activation, and it probably plays an important role in adjusting T cell responsiveness. Conflicting data have been published on down-regulation and degradation rates of the individual TCR subunits, and several di...... to the lysosomes. Similar results were obtained in studies of primary human Vbeta8+ T cells stimulated with superantigen. Based on these results, the simplest model for TCR internalization, sorting, and degradation is proposed.......Modulation of TCR expression levels is a central event during T cell development and activation, and it probably plays an important role in adjusting T cell responsiveness. Conflicting data have been published on down-regulation and degradation rates of the individual TCR subunits, and several...... divergent models for TCR down-regulation and degradation have been suggested. The aims of this study were to determine the rate constants for constitutive and ligand-induced TCR degradation and to determine whether the TCR subunits segregate or are processed as an intact unit during TCR down...

Degradation of chlorpyrifos contaminated soil by bioslurry reactor operated in sequencing batch mode: bioprocess monitoring

International Nuclear Information System (INIS)

Mohan, S. Venkata; Sirisha, K.; Rao, N. Chandrasekhara; Sarma, P.N.; Reddy, S. Jayarama

2004-01-01

Bioslurry reactor (SS-SBR) was studied for the degradation of chlorpyrifos contaminated soil using native mixed microflora, by adopting sequencing batch mode (anoxic-aerobic-anoxic) operation. Reactor operation was monitored for a total cycle period of 72 h consisting of 3 h of FILL, 64 h REACT, 2 h of SETTLE, and 3 h of DECANT with chlorpyrifos concentrations of 3000 μg/g, 6000 μg/g and 12000 μg/g. At 3000 μg/g of chlorpyrifos concentration, 91% was degraded after 72 h of the cycle period, whereas in the case of 6000 μg/g of chlorpyrifos, 82.5% was degraded. However, for 12000 μg/g of chlorpyrifos, only 14.5% degradation was observed. The degradation rate was rapid at lower substrate concentration and 12000 μg/g of substrate concentration was found to be inhibitory. Chlorpyrifos removal rate was slow during the initial phase of the sequence operation. Half-life of chlorpyrifos degradation (t 0.5 ) was estimated to be 6.3 h for 3000 μg/g of substrate, 17.5 h for 6000 μg/g and 732.2 h for 12000 μg/g. Process performance was assessed by monitoring chlorpyrifos concentration and biochemical process parameters viz., pH, oxidation and reduction potential (ORP), dissolved oxygen (DO), oxygen consumption rate (OCR) and microbial count (CFU) during sequence operation. From the experimental data obtained it can be concluded that the rate-limiting step with the bioslurry phase reactor in the process of chlorpyrifos degradation may be attributed to the concentration of substrate present in either soil or liquid phase. Periodic operations (SBR) by varying individual components of substrate with time in each process step place micro-organisms under nutritional changes from feast to famine and maintains a wide distribution in the population of micro-organisms resulting in high uptake of the substrate in the bioslurry reactor

Degradation of chlorpyrifos contaminated soil by bioslurry reactor operated in sequencing batch mode: bioprocess monitoring

Energy Technology Data Exchange (ETDEWEB)

Mohan, S. Venkata [Biochemical and Environmental Engineering Centre, Indian Institute of Chemical Technology, Hyderabad 500007 (India); Sirisha, K. [Electrochemical Research Laboratories, Department of Chemistry, Sri Venkateswara University, Tirupati 517502 (India); Rao, N. Chandrasekhara [Biochemical and Environmental Engineering Centre, Indian Institute of Chemical Technology, Hyderabad 500007 (India); Sarma, P.N. [Biochemical and Environmental Engineering Centre, Indian Institute of Chemical Technology, Hyderabad 500007 (India); Reddy, S. Jayarama [Electrochemical Research Laboratories, Department of Chemistry, Sri Venkateswara University, Tirupati 517502 (India)]. E-mail: profjreddy_s@yahoo.co.in

2004-12-10

Bioslurry reactor (SS-SBR) was studied for the degradation of chlorpyrifos contaminated soil using native mixed microflora, by adopting sequencing batch mode (anoxic-aerobic-anoxic) operation. Reactor operation was monitored for a total cycle period of 72 h consisting of 3 h of FILL, 64 h REACT, 2 h of SETTLE, and 3 h of DECANT with chlorpyrifos concentrations of 3000 {mu}g/g, 6000 {mu}g/g and 12000 {mu}g/g. At 3000 {mu}g/g of chlorpyrifos concentration, 91% was degraded after 72 h of the cycle period, whereas in the case of 6000 {mu}g/g of chlorpyrifos, 82.5% was degraded. However, for 12000 {mu}g/g of chlorpyrifos, only 14.5% degradation was observed. The degradation rate was rapid at lower substrate concentration and 12000 {mu}g/g of substrate concentration was found to be inhibitory. Chlorpyrifos removal rate was slow during the initial phase of the sequence operation. Half-life of chlorpyrifos degradation (t{sub 0.5}) was estimated to be 6.3 h for 3000 {mu}g/g of substrate, 17.5 h for 6000 {mu}g/g and 732.2 h for 12000 {mu}g/g. Process performance was assessed by monitoring chlorpyrifos concentration and biochemical process parameters viz., pH, oxidation and reduction potential (ORP), dissolved oxygen (DO), oxygen consumption rate (OCR) and microbial count (CFU) during sequence operation. From the experimental data obtained it can be concluded that the rate-limiting step with the bioslurry phase reactor in the process of chlorpyrifos degradation may be attributed to the concentration of substrate present in either soil or liquid phase. Periodic operations (SBR) by varying individual components of substrate with time in each process step place micro-organisms under nutritional changes from feast to famine and maintains a wide distribution in the population of micro-organisms resulting in high uptake of the substrate in the bioslurry reactor.

Microbial degradation rates of small peptides and amino acids in the oxygen minimum zone of Chilean coastal waters

Science.gov (United States)

Pantoja, Silvio; Rossel, Pamela; Castro, Rodrigo; Cuevas, L. Antonio; Daneri, Giovanni; Córdova, Candy

2009-07-01

We found similar microbial degradation rates of labile dissolved organic matter in oxic and suboxic waters off northern Chile. Rates of peptide hydrolysis and amino acid uptake in unconcentrated water samples were not low in the water column where oxygen concentration was depleted. Hydrolysis rates ranged from 65 to 160 nmol peptide L -1 h -1 in the top 20 m, 8-28 nmol peptide L -1 h -1 between 100 and 300 m (O 2-depleted zone), and 14-19 nmol peptide L -1 h -1 between 600 and 800 m. Dissolved free amino acid uptake rates were 9-26, 3-17, and 6 nmol L -1 h -1 at similar depth intervals. Since these findings are consistent with a model of comparable potential activity of microbes in degrading labile substrates of planktonic origin, we suggest, as do other authors, that differences in decomposition rates with high and low oxygen concentrations may be a matter of substrate lability. The comparison between hydrolysis and uptake rates indicates that microbial peptide hydrolysis occurs at similar or faster rates than amino acid uptake in the water column, and that the hydrolysis of peptides is not a rate-limiting step for the complete remineralization of labile macromolecules. Low O 2 waters process about 10 tons of peptide carbon per h, double the amount processed in surface-oxygenated water. In the oxygen minimum zone, we suggest that the C balance may be affected by the low lability of the dissolved organic matter when this is upwelled to the surface. An important fraction of dissolved organic matter is processed in the oxygen minimum layer, a prominent feature of the coastal ocean in the highly productive Humboldt Current System.

Irradiation degradation of chlorpyrifos in water solution and asparagus

International Nuclear Information System (INIS)

Zhang Qingfang; Wang Feng; Ha Yiming; Li An; Yin Qinggang

2009-01-01

In order to seek an effective technique to degrade chlorpyrifos residue, chlorpyrifos water solution and asparagus containing chlorpyrifos as testing materials were irradiated by 60 Co γ-rays and their degradation rate were determined and compared. The results show the degradation rate in water-solution increases with irradiation dose in the range of 0 and 12 kGy, and it reached 95.5% at 4 kGy. The degradation rate of chlorpyrifos in asparagus is low and comes to the maximum of 30.0% when the dose is 8 kGy. Further study indicates that vitamin C, violaquercitrin and total sugar inhibit the irradiation degradation of chlorpyrifos in asparagus. (authors)

A Selective High Performance Liquid Chromatographic Method to Follow the Hydrolytic Degradation of Nicardipine Hydrochloride

Directory of Open Access Journals (Sweden)

K. E. Ibrahim

2010-01-01

Full Text Available A simple, stability indicating, reverse phase high performance liquid chromatographic method was developed and validated for determination of nicardipine hydrochloride (NC in the presence of its degradation products. The chromatographic separation was performed on Hypersil, BDS-C18, 30 cm × 3.9 mm id, at ambient temperature with UV-detection at 254 nm. A mixture of 20% (v/v aqueous 0.01 M sodium acetate∕acetic acid buffer (pH 4.5 and 80% acetonitrile was used as the mobile phase at a flow rate of 1.5 mL min-1, losartan was used as internal standard. The calibration curve is linear over the concentration range 5-40 μg mL-1, with a regression coefficient of 0.9984 and the % recovery was 99.78±0.17. The method was used to investigate the kinetics of alkaline, acids induced degradation, effect of buffer concentration and temperature. The degradation followed first-order kinetics. The rate constant, half-life time, and activation energy were calculated

Earthworms (Eisenia fetida) demonstrate potential for use in soil bioremediation by increasing the degradation rates of heavy crude oil hydrocarbons.

Science.gov (United States)

Martinkosky, Luke; Barkley, Jaimie; Sabadell, Gabriel; Gough, Heidi; Davidson, Seana

2017-02-15

Crude oil contamination widely impacts soil as a result of release during oil and gas exploration and production activities. The success of bioremediation methods to meet remediation goals often depends on the composition of the crude oil, the soil, and microbial community. Earthworms may enhance bioremediation by mixing and aerating the soil, and exposing soil microorganisms to conditions in the earthworm gut that lead to increased activity. In this study, the common composting earthworm Eisenia fetida was tested for utility to improve remediation of oil-impacted soil. E. fetida survival in soil contaminated with two distinct crude oils was tested in an artificial (lab-mixed) sandy loam soil, and survival compared to that in the clean soil. Crude oil with a high fraction of light-weight hydrocarbons was more toxic to earthworms than the crude oil with a high proportion of heavy polyaromatic and aliphatic hydrocarbons. The heavier crude oil was added to soil to create a 30,000mg/kg crude oil impacted soil, and degradation in the presence of added earthworms and feed, feed alone, or no additions was monitored over time and compared. Earthworm feed was spread on top to test effectiveness of no mixing. TPH degradation rate for the earthworm treatments was ~90mg/day slowing by 200days to ~20mg/day, producing two phases of degradation. With feed alone, the rate was ~40mg/day, with signs of slowing after 500days. Both treatments reached the same end point concentrations, and exhibited faster degradation of aliphatic hydrocarbons C21, decreased. During these experiments, soils were moderately toxic during the first three months, then earthworms survived well, were active and reproduced with petroleum hydrocarbons present. This study demonstrated that earthworms accelerate bioremediation of crude oil in soils, including the degradation of the heaviest polyaromatic fractions. Copyright © 2016 Elsevier B.V. All rights reserved.

A Comparison of the Predicted Tube Plugging Rate for Alloy 600HTMA Steam Generator

Energy Technology Data Exchange (ETDEWEB)

Boo, Myung Hwan; Kang, Yong Seok [Korea Hydro and Nuclear Power Co., Daejeon (Korea, Republic of)

2010-10-15

To manage components that are used in long term operations such as steam generation, it is important to know the tube plugging rate, which can cause the performance degradation. The life of components can be predicted by the method using determinism and probability theory. With a method using probability theory, damage prediction of tube is possible. In this study, damage prediction for steam generation (SG) tube is performed using Weibull distribution and predicted plugging rate (life) is compared with the simple sum plugging number and case by case (failure cause) plugging number

Life cycle management of service water systems

International Nuclear Information System (INIS)

Egan, Geoffrey R.; Besuner, Philip M.; Mahajan, Sat P.

2004-01-01

As nuclear plants age, more attention must focus on age and time dependent degradation mechanisms such as corrosion, erosion, fatigue, etc. These degradation mechanisms can best be managed by developing a life cycle management plan which integrates past historical data, current conditions and future performance needs. In this paper we present two examples of life cycle management. In the first example, the 20-year maintenance history of a sea water cooling system (cement-lined, cast iron) is reviewed to develop attributes like maintenance cost, spare part inventory, corrosion, and repair data. Based on this information, the future expected damage rate was forecast. The cost of managing the future damage was compared with the cost to replace (in kind and with upgraded materials. A decision optimization scheme was developed to choose the least cost option from: a) Run as-is and repair; b) replace in kind; or c) replace with upgraded material and better design. In the second example, life cycle management techniques were developed for a ceilcote lined steel pipe cooling water system. Screens (fixed and traveling), filters, pumps, motors, valves, and piping were evaluated. (author)

Life satisfaction after traumatic brain injury: comparison of ratings with the Life Satisfaction Questionnaire (LiSat-11) and the Satisfaction With Life Scale (SWLS).

Science.gov (United States)

Jacobsson, Lars; Lexell, Jan

2016-01-15

An optimal life satisfaction (LS) is considered an important long-term outcome after a traumatic brain injury (TBI). It is, however, not clear to what extent a single instrument captures all aspects of LS, and different instruments may be needed to comprehensively describe LS. The aim of this study was to compare self-ratings of life satisfaction after a TBI with two commonly used instruments. Life Satisfaction Questionnaire (LiSat-11), comprising eleven items and Satisfaction With Life Scale (SWLS), comprising five items, were administered to 67 individuals (51 men and 16 women). Secondary analysis of data collected as part of a survey of individuals with TBI 6 to 15 years post TBI. Item 1 in LiSat-11 ('Life as a whole') and the total SWLS score was strongly correlated (Spearman's rho = 0.66; p life' and 'Partner relationship', were moderately to strongly correlated with items in SWLS. The item 'Partner relationship' in LiSat-11 did not correlate with any of the items in SWLS or the total score. The item 'If I could live my life over, I would change nothing' in SWLS had the weakest correlations with items in LiSat-11. Items 'Vocation' and 'Leisure' in LISat-11 were most strongly correlated with items in SWLS, whereas the item 'ADL' in LiSat-11 was more weakly correlated with items in SWLS. The strength of the relationships implies that the two instruments assess similar but not identical aspects of LS and therefore complement each other when it is rated.

A proposal of parameter determination method in the residual strength degradation model for the prediction of fatigue life (I)

International Nuclear Information System (INIS)

Kim, Sang Tae; Jang, Seong Soo

2001-01-01

The static and fatigue tests have been carried out to verify the validity of a generalized residual strength degradation model. And a new method of parameter determination in the model is verified experimentally to account for the effect of tension-compression fatigue loading of spheroidal graphite cast iron. It is shown that the correlation between the experimental results and the theoretical prediction on the statistical distribution of fatigue life by using the proposed method is very reasonable. Furthermore, it is found that the correlation between the theoretical prediction and the experimental results of fatigue life in case of tension-tension fatigue data in composite material appears to be reasonable. Therefore, the proposed method is more adjustable in the determination of the parameter than maximum likelihood method and minimization technique

Effects of low dose rate irradiation on life span prolongation of human premature-aging syndrome model mice

International Nuclear Information System (INIS)

Nomura, Takaharu

2006-01-01

We previously showed that Type II diabetes model mice prolonged of their life span by life long low dose rate irradiation. We also found that antioxidant function in variety tissues of some strain of mice were enhancement after low dose/low dose rate irradiation. The prolongation of life span might depend on certain damaged level of reactive oxygen species. We thought the effect of the prolongation was due to the enhancement of the antioxidant activities after irradiation. We investigated whether the enhancement of antioxidant activities after low dose rate irradiation had an effect on life span prolongation. Four-week-old female human premature-aging syndrome model mice, kl/kl (klotho) mice, which the life span of this model mouse is about 65 days, were irradiated with gamma rays at 0.35, 0.70 or 1.2 mGy/hr. The 0.70 mGy/hr-irradiated group remarkably effected on the prolongation of their life span. Some mice of the group were extremely survived for about and more 100 days. Antioxidant activities in the irradiated groups were enhancement by low dose rate irradiation, however the dependence of the dose rates were not clearly difference. These results suggest that the antioxidant activities in this model mouse were enhanced by the low dose rate irradiation, and may make it possible to prolong the life span of this mouse. (author)

Stator winding service life analysis of wet winding motor RCP

International Nuclear Information System (INIS)

Yeoh Eingyee; Li Linsen; Wang Ziguan; Shen Feng

2017-01-01

The reactor coolant pump type RUV of KSB is specially designed for the Westinghouse AP1000 reactor. It is hermetically sealed, wet winding motor pump. This wet winding motor concept has higher efficiency as compared to a canned motor since there are no eddy current losses, but this makes the stator cable insulator face the challenge of degradation by γ-irradiation in coolant. Radiation dose at the RUV is evaluated in interest from the material degradation point of view and the service life of stator winding in RUV is preliminarily analyzed. The values obtained are less than the dose rate and the dose which change the mechanical properties of the insulator material. According to the preliminary analysis, it can be concluded that the degradation of cable insulator of stator winding by γ-irradiation in coolant is negligible for the 60 years' service life of reactor coolant pump. This result also ensures crosslinked polyethylene used as cable insulator of stator winding is reliable in reactor coolant pump. (author)

Does adversity early in life affect general population suicide rates? A cross-national study.

Science.gov (United States)

Shah, Ajit; Bhandarkar, Ritesh

2011-01-01

Adversity early in life has been suggested as a protective factor for elderly suicides. However, studies examining this relationship in general population suicide rates are scarce. The relationship between general population suicide rates and four proxy measures of adversity earlier in life was examined using data from the World Health Organization and the United Nations data banks. General population suicide rates were negatively correlated with the percentage of children under the age of 5 years who were underweight, the percentage of children under the age of 5 years who were under height, the percentage of infants with low birth weight babies, and the percentage of the general population that was undernourished. The only independent predictor general population suicide rates in both sexes, on multiple regression analysis, was the Gini coefficient (a measure of income inequality). Income inequality may lead to low birth weight, undernourishment, underweight and under height because income inequality results in poor access to healthcare and nutrition. These adversities may increase child mortality rates and reduce life expectancy. Those surviving into adulthood in countries with greater adversity early in life may be at reduced risk of suicide because of selective survival of those at reduced risk of suicide due to constitutional or genetic factors and development of greater tolerance to hardship in adulthood. ‎

Does adversity early in life affect general population suicide rates? a cross-national study

Directory of Open Access Journals (Sweden)

Ritesh Bhandarkar

2011-01-01

Full Text Available BACKGROUND: Adversity early in life has been suggested as a protective factor for elderly suicides. However, studies examining this relationship in general population suicide rates are scarce. METHODS: The relationship between general population suicide rates and four proxy measures of adversity earlier in life was examined using data from the World Health Organization and the United Nations data banks. RESULTS: General population suicide rates were negatively correlated with the percentage of children under the age of 5 years who were underweight, the percentage of children under the age of 5 years who were under height, the percentage of infants with low birth weight babies, and the percentage of the general population that was undernourished. The only independent predictor general population suicide rates in both sexes, on multiple regression analysis, was the Gini coefficient (a measure of income inequality. CONCLUSIONS: Income inequality may lead to low birth weight, undernourishment, underweight and under height because income inequality results in poor access to healthcare and nutrition. These adversities may increase child mortality rates and reduce life expectancy. Those surviving into adulthood in countries with greater adversity early in life may be at reduced risk of suicide because of selective survival of those at reduced risk of suicide due to constitutional or genetic factors and development of greater tolerance to hardship in adulthood.

Degradation rates and mechanisms of acid-resistant coatings in copper-leaching tanks

DEFF Research Database (Denmark)

Møller, Victor Buhl

coating where the lifetime was estimated to 1:6 ± 0:2 and 1:4 ± 0:1 years, respectively. Part IV A series of newly designed and constructed diffusion cells were used to measure sulfuric acid diffusion rates through the coatings. A mathematical model was developed to simulate the experimental data...... potential in the mineral industry has not yet been thoroughly investigated. This particular industry poses unique challenges, with high operational temperatures (around 75 °C) and combined acidicerosive environments. The use of organic coatings to protect tanks, pipes, and secondary exposure areas, may....... Part I An in-depth literature study was performed to uncover and review uses and limitations ofacid-resistant coatings in the chemical industry, with a comparison to alternative resistant materialsbased on metals and ceramics. In addition, coating degradation phenomena caused by acid exposure, were...

Degradation of 17α-ethinylestradiol in water by heterogeneous photocatalysis

Directory of Open Access Journals (Sweden)

Wilton Silva Lopes

2015-11-01

Full Text Available We investigated the degradation of 17α-ethynylestradiol in an aqueous solution using a batch heterogeneous photocatalytic (HPC reactor with ultraviolet (UV light and TiO2 catalyst. In order to determine appropriate operating conditions, a 23 factorial experiment was conducted with initial an substrate concentration of 15 or 30 mg L-1, TiO2 concentration of 0.02 or 0.05%, pH of 5.0 or 9.0 and total reaction time 240 min. Degradation profiles and kinetic parameters were determined with an initial substrate concentration of 15 or 30 mg L-1, 0.02% TiO2 and pH 7.0.With17α-ethynylestradiol at 15 mg L-1, degradation efficiency was 100% after 120 min independent of TiO2 concentration and pH. However, less than 50% of the substrate was degraded when the initial concentration was 30 mg L-1 (0.05% TiO2 and pH 5.0. Initial substrate concentration was a limiting factor for HPC, although the reaction was also strongly influenced by TiO2 concentration and the interaction between initial substrate concentration and TiO2 concentration. All degradations followed first-order kinetics. With 17α-ethynylestradiol at 15 mg L-1, the half-life time (t½ was 64.16 min and the rate constant was 0.108 min-1, while at 30 mg L-1, substrate degradation proceeded in two stages, the t½ values of which were 44.71 and 433.12 min.

Fractional rate of degradation (kd) of starch in the rumen and its relation to in vivo rumen and total digestibility

DEFF Research Database (Denmark)

Hvelplund, Torben; Larsen, Mogens; Lund, Peter

2009-01-01

in different ways both chemically and physically. The starch sources were fed in mixed diets together with grass silage and soya bean meal and allocated ad libitum to fistulated dairy cows. The starch content varied between 13 and 35% in ration dry matter for the different starch sources. The design...... was a series of cross-over experiments with two cows and two periods. Ruminal starch pool was estimated from rumen evacuation and starch flow was estimated by duodenal and faeces sampling. Fractional rate of rumen degradation was estimated from the equation [kd = rumen degraded/rumen pool] and rumen and total...

Degradation kinetics of ptaquiloside in soil and soil solution

DEFF Research Database (Denmark)

Ovesen, Rikke Gleerup; Rasmussen, Lars Holm; Hansen, Hans Christian Bruun

2008-01-01

and soil solutions in sandy and clayey soils subjected to high natural PTA loads from bracken stands. Degradation kinetics in moist soil could be fitted with the sum of a fast and a slow first-order reaction; the fast reaction contributed 20 to 50% of the total degradation of PTA. The fast reaction...... was similar in all horizons, with the rate constant k1F ranging between 0.23 and 1.5/h. The slow degradation, with the rate constant k1S ranging between 0.00067 and 0.029/h, was more than twice as fast in topsoils compared to subsoils, which is attributable to higher microbial activity in topsoils....... Experiments with sterile controls confirmed that nonmicrobial degradation processes constituted more than 90% of the fast degradation and 50% of the slow degradation. The lower nonmicrobial degradation rate observed in the clayey compared with the sandy soil is attributed to a stabilizing effect of PTA...

26 CFR 1.167(d)-1 - Agreement as to useful life and rates of depreciation.

Science.gov (United States)

2010-04-01

... depreciation. 1.167(d)-1 Section 1.167(d)-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE... and Corporations § 1.167(d)-1 Agreement as to useful life and rates of depreciation. After August 16... respect to the estimated useful life, method and rate of depreciation and treatment of salvage of any...

Preparation of H3PW12O40/MCM-48 and its photocatalytic degradation of pesticides.

Science.gov (United States)

Liu, Xia; Li, Yan-zhou; Gan, Qiang; Feng, Chang-gen

2014-08-01

A composite catalyst H3PW12O40/MCM-48 was prepared by loading photocatalyst phosphotungstic acid H3PW12O40 (HPW) to molecular sieve MCM-48 by impregnation method, and its structure was characterized by Fourier transform infrared (FT-IR) spectra, small angle X-ray diffraction (XRD) patterns, nitrogen adsorption analysis and High-resolution transmission electron microscopy (HRTEM) analysis. Photocatalytic degradation activities of HPW/MCM-48 against pesticides imidacloprid and paraquat were evaluated under UV radiation (365 nm). The results show that HPW/MCM-48 maintains the mesoprous molecular sieve structure of MCM-48 and the Keggin structure of HPW, while the BET surface area is 793.35 m2 x g(-1), pore volume is 1.46 cm3 x g(-1), average pore diameter is 2.76 nm, suggesting loading HPW on MCM-48 is a considerable way to improve its surface area. After 14 h UV irradiation (365 nm), 57.38% imidacloprid and 63.79% paraquat were degraded by 20 mg HPW/MCM-48 catalyst, while HPW and blank group degraded the two pesticides at the degradation rate of about 25% and 5%, respectively. Implying loading on MCM-48 could greaterly improve the degradation activity of HPW. The reslut of degradation kinetics show that, the degradation process of HPW/MCM-48 fits first order kinetics equation. The rate constant Ka of HPW/MCM-48 toward imidacloprid and paraquat are 0.089 h and 0.117 h, with the half-life t(1/2) of 7.8 h and 5.9 h, respectively.

Evaluation of long-term creep-fatigue life of stainless steel weldment based on a microstructure degradation model

International Nuclear Information System (INIS)

Asayama, Tai; Hasebe, Shinichi

1997-01-01

This paper describes a newly developed analytical method of evaluation of creep-fatigue strength of stainless weld metals. Based on the observation that creep-fatigue crack initiates adjacent to the interface of sigma-phase/delta-ferrite and matrix, a mechanistic model which allows the evaluation of micro stress/strain concentration adjacent to the interface was developed. Fatigue and creep damage were evaluated using the model which describes the microstructure after exposed to high temperatures for a long time. Thus it was made possible to predict analytically the long-term creep-fatigue life of stainless steel metals whose microstructure is degraded as a result of high temperature service. (author)

Changes in collagen synthesis and degradation during skeletal muscle growth

International Nuclear Information System (INIS)

Laurent, G.J.; McAnulty, R.J.; Gibson, J.

1985-01-01

The changes in collagen metabolism during skeletal muscle growth were investigated by measuring rates of synthesis and degradation during stretch-induced hypertrophy of the anterior latissimus dorsi muscle of the adult chicken (Gallus domesticus). Synthesis rates were obtained from the uptake of tritiated proline injected intravenously with a flooding dose of unlabeled proline. Degradation of newly synthesized and ''mature'' collagen was estimated from the amount of hydroxyproline in the free pool as small molecular weight moieties. In normal muscle, the synthesis rate was 1.1 +/- 0.3%/day, with 49 +/- 7% of the newly produced collagen degraded rapidly after synthesis. During hypertrophy there was an increase of about fivefold in the rate of synthesis (P less than 0.01), a 60% decrease in the rate of degradation of newly synthesized collagen (P less than 0.02), and an increase of about fourfold in the amount of degradation of mature collagen (P less than 0.01). These results suggest an important role for degradative as well as synthetic processes in the regulation of collagen mass. They indicate that enhanced degradation of mature collagen is required for muscle growth and suggest a physiological role for the pathway whereby in normal muscle, a large proportion of newly produced collagen is rapidly degraded

Chromatographic determination of itopride hydrochloride in the presence of its degradation products.

Science.gov (United States)

Kaul, Neeraj; Agrawal, Himani; Maske, Pravin; Rao, Janhavi Ramchandra; Mahadik, Kakasaheb Ramoo; Kadam, Shivajirao S

2005-08-01

Two sensitive and reproducible methods are described for the quantitative determination of itopride hydrochloride (IH) in the presence of its degradation products. The first method is based on HPLC separation on a reversed phase Kromasil column [C18 (5-microm, 25 cm x 4.6 mm, ID)] at ambient temperature using a mobile phase consisting of methanol and water (70:30, v/v) adjusted to pH 4.0 with orthophosphoric acid with UV detection at 258 nm. The flow rate was 1.0 mL per min with an average operating pressure of 180 kg/cm2. The second method is based on HPTLC separation on silica gel 60 F254 using toluene:methanol:chloroform:10% ammonia (5.0:3.0:6.0:0.1, v/v/v/v) as mobile phase at 270 nm. The analysis of variance (ANOVA) and Student's t-test were applied to correlate the results of IH determination in dosage form by means of HPLC and HPTLC methods. The drug was subjected to acid and alkali hydrolysis, oxidation, dry heat, wet heat treatment, UV, and photodegradation. The proposed HPLC method was utilized to investigate the kinetics of the acidic, alkaline, and oxidative degradation processes at different temperatures and the apparent pseudo-first-order rate constant, half-life, and activation energy were calculated. In addition the pH-rate profile of degradation of IH in constant ionic strength buffer solutions in the pH range 2-11 was studied.

On preventive maintenance policy of a critical reliability level for system subject to degradation

International Nuclear Information System (INIS)

Zhao, Y.X.

2003-01-01

Conventional preventive maintenance (PM) policies generally hold same time interval for PM actions and are often applied with known failure modes. The same time interval will give unavoidably decreasing reliabilities at the PM actions for degradation system with imperfect PM effect and the known failure modes may be inaccurate in practice. Therefore, field managers would prefer policy with an acceptable reliability level to keep system often at a good state. A PM policy with the critical reliability level is presented to address the preference of field managers. Through assuming that system after a PM action starts a new failure process, a parameter so-called degradation ratio is introduced to represent the imperfect effect. The policy holds a law that there is same number of failures in the time intervals of various PM cycles, and same degradation ratio for the system reliability or benefit parameters such as the optimal time intervals and the hazard rates between the neighboring PM cycles. This law is valid to any of the failure modes that could be appropriately referred as a 'general isodegrading model', and the degradation ratio as a 'general isodegrading ratio'. In addition, life cycle availability and cost functions are derived for system with the policy. An analysis of the field data of a loading and unloading machine indicates that the reliability, availability and cost in life cycle might be well modeled by the present theory and approach

Degradation modeling with application to aging and maintenance effectiveness evaluations

International Nuclear Information System (INIS)

Samanta, P.K.; Hsu, F.; Subduhi, M.; Vesely, W.E.

1990-01-01

This paper describes a modeling approach to analyze component degradation and failure data to understand the aging process of components. As used here, degradation modeling is the analysis of information on component degradation in order to develop models of the process and its implications. This particular modeling focuses on the analysis of the times of component degradations, to model how the rate of degradation changes with the age of the component. The methodology presented also discusses the effectiveness of maintenance as applicable to aging evaluations. The specific applications which are performed show quantitative models of component degradation rates and component failure rates from plant-specific data. The statistical techniques which are developed and applied allow aging trends to be effectively identified in the degradation data, and in the failure data. Initial estimates of the effectiveness of maintenance in limiting degradations from becoming failures also are developed. These results are important first steps in degradation modeling, and show that degradation can be modeled to identify aging trends. 2 refs., 8 figs

Degradation modeling with application to aging and maintenance effectiveness evaluations

International Nuclear Information System (INIS)

Samanta, P.K.; Vesely, W.E.; Hsu, F.; Subudhi, M.

1991-01-01

This paper describes a modeling approach to analyze light water reactor component degradation and failure data to understand the aging process of components. As used here, degradation modeling is the analysis of information on component degradation in order to develop models of the process and its implications. This particular modeling focuses on the analysis of the times of component degradations, to model how the rate of degradation changes with the age of the component. The methodology presented also discusses the effectiveness of maintenance as applicable to aging evaluations. The specific applications which are performed show quantitative models of component degradation rates and component failure rates from plant-specific data. The statistical techniques which are developed and applied allow aging trends to be effectively identified in the degradation data, and in the failure data. Initial estimates of the effectiveness of maintenance in limiting degradations from becoming failures also are developed. These results are important first steps in degradation modeling, and show that degradation can be modeled to identify aging trends

Estimation of material degradation of VVER-1000 baffle

Science.gov (United States)

Harutyunyan, Davit; Koš'ál, Michal; Vandlík, Stanislav; Hojná, Anna; Schulc, Martin; Flibor, Stanislav

2017-09-01

The planned lifetime of the first commercial VVER-1000 units were designed for 30 to 35 years. Most of the early VVER plants are now reaching and/or passing the 35-year mark. Service life extension for another 10 to 30 years is now under investigation. Life extension requires the evaluation of pressure vessel internals degradation under long-term irradiation. One of the possible limiting factors for the service life of VVERs is a void swelling of the Russian type titanium stabilized stainless 08Ch18N10T steel used to construct the baffle surrounding the core. This article aims to show first steps towards deeper analysis of the baffle degradation process and to demonstrate the possibilities of precise calculation and measurements on the VVER-1000 mock-up in LR-0 reactor.

Degradation of 3-phenoxybenzoic acid by a Bacillus sp.

Directory of Open Access Journals (Sweden)

Shaohua Chen

Full Text Available 3-Phenoxybenzoic acid (3-PBA is of great environmental concern with regards to endocrine disrupting activity and widespread occurrence in water and soil, yet little is known about microbial degradation in contaminated regions. We report here that a new bacterial strain isolated from soil, designated DG-02, was shown to degrade 95.6% of 50 mg·L(-1 3-PBA within 72 h in mineral salt medium (MSM. Strain DG-02 was identified as Bacillus sp. based on the morphology, physio-biochemical tests and 16S rRNA sequence. The optimum conditions for 3-PBA degradation were determined to be 30.9°C and pH 7.7 using response surface methodology (RSM. The isolate converted 3-PBA to produce 3-(2-methoxyphenoxy benzoic acid, protocatechuate, phenol, and 3,4-dihydroxy phenol, and subsequently transformed these compounds with a q(max, K(s and K(i of 0.8615 h(-1, 626.7842 mg·L(-1 and 6.7586 mg·L(-1, respectively. A novel microbial metabolic pathway for 3-PBA was proposed on the basis of these metabolites. Inoculation of strain DG-02 resulted in a higher degradation rate on 3-PBA than that observed in the non-inoculated soil. Moreover, the degradation process followed the first-order kinetics, and the half-life (t(1/2 for 3-PBA was greatly reduced as compared to the non-inoculated control. This study highlights an important potential application of strain DG-02 for the in situ bioremediation of 3-PBA contaminated environments.

Ratings of Severity of Life Events by Ninth-Grade Students.

Science.gov (United States)

Hutton, Jerry B.; And Others

1987-01-01

Special education, basic, and honors ninth-grade students (n=60) rated the severity of stress for each of the life events on the Source of Stress Inventory (Chandler, 1981). There was a significant positive relationship between the Chandler rankings (teachers and mental health workers) and the student rankings. (Author/NB)

Cycle Life of Commercial Lithium-Ion Batteries with Lithium Titanium Oxide Anodes in Electric Vehicles

Directory of Open Access Journals (Sweden)

Xuebing Han

2014-07-01

Full Text Available The lithium titanium oxide (LTO anode is widely accepted as one of the best anodes for the future lithium ion batteries in electric vehicles (EVs, especially since its cycle life is very long. In this paper, three different commercial LTO cells from different manufacturers were studied in accelerated cycle life tests and their capacity fades were compared. The result indicates that under 55 °C, the LTO battery still shows a high capacity fade rate. The battery aging processes of all the commercial LTO cells clearly include two stages. Using the incremental capacity (IC analysis, it could be judged that in the first stage, the battery capacity decreases mainly due to the loss of anode material and the degradation rate is lower. In the second stage, the battery capacity decreases much faster, mainly due to the degradation of the cathode material. The result is important for the state of health (SOH estimation and remaining useful life (RUL prediction of battery management system (BMS for LTO batteries in EVs.

APOE ε4, Rated Life Experiences, and Affect among Centenarians

Science.gov (United States)

Martin, Peter; Jazwinski, S. Michal; Davey, Adam; Green, Robert; MacDonald, Maurice; Margrett, Jennifer A.; Siegler, Ilene C.; Arnold, Jonathan; Woodard, John; Johnson, Mary Ann; Kim, Sangkyu; Dai, Jianliang; Li, Li; Batzer, Mark A.; Poon, Leonard W.

2013-01-01

The purpose of this study was to assess the relationship between APOE, life events and engagement, and subjective well-being (as measured by positive and negative affect) among centenarians. Based on the life stress paradigm, we predicted that higher levels of stress would allow APOE to influence positive and negative affect. One hundred and ninety six centenarians and near centenarians (98 years and older) of the Georgia Centenarian Study participated in this research. APOE, positive and negative affect, number of recent (last two years) and life-long (more than 20 years prior to testing) events, as well as a number of life engagement tasks were assessed. Results suggested that centenarians carrying the APOE ε4 allele rated lower in positive affect, number of life-long events, and in engaged lifestyle when compared to centenarians without the APOE ε4 allele (t = 3.43, p < .01, t = 3.19, p < .01, and t = 2.33, p < .05, respectively). Blockwise multiple regressions indicated that APOE ε4 predicted positive but not negative affect after controlling for demographics. Gene-environment interactions were obtained for APOE ε4 and life-long events, suggesting that carriers of the APOE ε4 allele had higher scores of negative affect after having experienced more events, whereas non-carriers had reduced negative affect levels after having experienced more events. PMID:23998924

Evaluation of the strain rate effects on environmental fatigue life of CF8M cast stainless steel

International Nuclear Information System (INIS)

Jeong, Ill Seok; Ha, Gak Hyun; Jeon, Hyun Ik

2009-01-01

The environmental fatigue life of CF8M cast stainless steel is influenced by mechanical, environmental and metallurgical parameters, such as strain rate, strain amplitude, temperature, dissolved oxygen concentration, water flow rate and so on. In an actual plant, the mechanical and environmental parameters are changing during the plant operation. Therefore, the effect of such mechanical and environmental parameter changes on fatigue life evaluation have to be studied. Low cycle fatigue life of structural materials diminishes remarkably as functions of various parameters in high temperature and high pressure environments. Such reduction can be estimated by the fatigue life reduction factor(F en ). In this study, fatigue tests were performed under changing conditions of strain amplitude, strain rate. Fatigue life was measured in terms of the number of cycles with the variation of strain amplitudes at 0.004 %/s strain rate, and the fatigue life correction factor was evaluated according to the equation modified by U. S. Nuclear Regulatory Commission(U.S.NRC) and Japanese Environmental Fatigue Tests committee (JEFT).

Multitracer test for the determination of transport and in-situ degradation of organic micro-contaminants in karst aquifers on the example of caffeine

Science.gov (United States)

Hillebrand, O.; Nödler, K.; Licha, T.; Geyer, T.

2012-04-01

investigated aquifer (R= 1.031-1.046) and is readily degradable (half-life t1/2= 90-105 h; temperature of the spring water T= 8-9 °C). The degradation rate is surprisingly high. In general, no significant degradation is believed to occur, during the rapid transport in karst systems. The high degradation rates of caffeine illustrate the potential to use this substance as reactive tracer to indicate biological activity within the aquifer. Due to the good degradability of caffeine it does not pose a threat as long-time contamination and can therefore safely be used as reactive tracer in aquifer systems.

Inspection and mitigating measures for life extension of nuclear power plant containment structures

International Nuclear Information System (INIS)

Meyers, B.L.; Daye, M.A.

1989-01-01

The subject of life extension of nuclear power plants has drawn considerable attention during the last few years. Interest in life extension initiated because of both safety and economic reasons. A number of evaluations have been performed. The main thrust of earlier work was directed toward evaluating the factors causing aging, and defining degradation sites, degradation mechanism and failure modes. At present, attention is directed toward establishing the appropriate inspection programs suitable for each of the defined aging sites. Some components and aging sites are already subjected to routine inspection programs such as the surveillance of post-tensioning system and the integrated leak rate test (ILRT) of prestressed concrete and reinforced concrete containments. The aging process affects mechanical, electrical and structural components in all types of containments. This paper addresses the structural components of PWR containments only and presents examples of inspection approaches and describes methods to prevent further degradation of select sites

Screening of an oil-degrading strain by N+ implantation and the oil degradation conditions

International Nuclear Information System (INIS)

Yan Yajuan; Li Zongwei; Qin Guangyong; Liu Jianling

2008-01-01

A strain DC-3-2-50 was obtained through N + implanting into Yarrowia lipolytica DC-3-2. An increase of 11.09% in the oil-degradation rate was obtained. The stain has good genetic stability after 10 times of subculture. The culturing condition of DC-3-2-50 was studied. The optimal culture conditions were as follow: initial pH value, 9.0; inoculum size, 3%; temperature, 25-28 degree C; dissolved oxygen, 180-200 rpm; and carbon nutriments soybean salad oil. The off-degradation rate can be up to 87.7%. (authors)

Degradation of shape memory effect

International Nuclear Information System (INIS)

Vandermeer, R.A.

1983-01-01

An important parameter for deciding whether or not a SME alloy is suitable for practical applications is the magnitude of the strain reversal accompanying martensite reversion. This research is concerned with elucidating metallurgical factors that cause degradation of this heat-activated recovery strain, E/sub R/. After explaining what is meant by degradation, two manifestations of degradation recently identified in near-monotectoid uranium-niobium alloys are described. The first was associated with the onset of plastic deformation of the martensite beyond the reversible strain limit, E/sub L/; a reduction of E/sub R/ from 5.25% at 8% total strain, i.e. E/sub L/, to 2.9% at 12% total strain was observed. A second type of degradation depended strongly on the heating rate during reversion; the E/sub R/ for an imposed strain of 6.95% was reduced from a value of 5.25% to 1.3% when the heating rate was decreased from 40 0 /sec to 0.05 0 /sec. Degradation was attributed to a change in the transformation path and the interjection of time-dependent, low temperature aging reactions

Analyses of component degradation to evaluate maintenance effectiveness and aging effects

International Nuclear Information System (INIS)

Samanta, P.K.; Hsu, F.; Subudhi, M.; Vesely, W.E.

1991-01-01

This paper describes degradation modeling, an approach for analyzing degradation and failure of components to understand the aging process of components. As used in our study, degradation modeling is the analysis of information on degradation of components for developing models of the degradation process and its implications. This modeling focuses on the analysis of the times of degradations of components, to model how the rate of degradation changes with the age of the component. With this methodology we also determine the effectiveness of maintenance as applicable to aging evaluations. The specific applications which are performed show quantitative models of degradation rates of components and failure rates of components from plant-specific data. The statistical techniques allow aging trends to be identified in the degradation data and in the failure data. Initial estimates of the effectiveness of maintenance in limiting degradations from becoming failures are developed. These results are important first steps in degradation modeling, and show that degradation can be modeled to identify aging trends. 2 refs., 8 figs., 1 tab

High-voltage pulsed life of multistressed polypropylene capacitor dielectric

International Nuclear Information System (INIS)

Laghari, J.R.

1992-01-01

High-voltage polypropylene capacitors were aged under singular as well as simultaneous multiple stresses (electrical, thermal, and radiation) at the University of Buffalo's 2 MW thermal nuclear reactor. These stresses were combined neutron-gamma radiation with a total dose of 1.6 x 10 6 rad, electrical stress at 40 V rms /μm, and thermal stress at 90 degrees C. After exposure, the polypropylene dielectric was tested for life (number of pulses to fail) under high-voltage high-repetition-rate (100 pps) pulses. Pulsed life data were also compared with ac life data. Results show that radiation stress causes the most degradation in life, either acting alone or in combination with other stresses. The largest reduction in life occurs when polypropylene is aged under simultaneous multiple stresses (electrical, thermal, and radiation). In this paper, it is shown that pulsed life can be equivalently compared with ac life

Degradation kinetics of ptaquiloside in soil and soil solution.

Science.gov (United States)

Ovesen, Rikke Gleerup; Rasmussen, Lars Holm; Hansen, Hans Christian Bruun

2008-02-01

Ptaquiloside (PTA) is a carcinogenic norsesquiterpene glycoside produced in bracken (Pteridium aquilinum (L.) Kuhn), a widespread, aggressive weed. Transfer of PTA to soil and soil solution eventually may contaminate groundwater and surface water. Degradation rates of PTA were quantified in soil and soil solutions in sandy and clayey soils subjected to high natural PTA loads from bracken stands. Degradation kinetics in moist soil could be fitted with the sum of a fast and a slow first-order reaction; the fast reaction contributed 20 to 50% of the total degradation of PTA. The fast reaction was similar in all horizons, with the rate constant k(1F) ranging between 0.23 and 1.5/h. The slow degradation, with the rate constant k(1S) ranging between 0.00067 and 0.029/ h, was more than twice as fast in topsoils compared to subsoils, which is attributable to higher microbial activity in topsoils. Experiments with sterile controls confirmed that nonmicrobial degradation processes constituted more than 90% of the fast degradation and 50% of the slow degradation. The lower nonmicrobial degradation rate observed in the clayey compared with the sandy soil is attributed to a stabilizing effect of PTA by clay silicates. Ptaquiloside appeared to be stable in all soil solutions, in which no degradation was observed within a period of 28 d, in strong contrast to previous studies of hydrolysis rates in artificial aqueous electrolytes. The present study predicts that the risk of PTA leaching is controlled mainly by the residence time of pore water in soil, soil microbial activity, and content of organic matter and clay silicates.

Associations of Various Health-Ratings with Geriatric Giants, Mortality and Life Satisfaction in Older People

DEFF Research Database (Denmark)

Puvill, Thomas; Lindenberg, Jolanda; Gussekloo, Jacobijn

2016-01-01

Self-rated health is routinely used in research and practise among general populations. Older people, however, seem to change their health perceptions. To accurately understand these changed perceptions we therefore need to study the correlates of older people's self-ratings. We examined self......-rated, nurse-rated and physician-rated health's association with common disabilities in older people (the geriatric giants), mortality hazard and life satisfaction. For this, we used an age-representative population of 501 participant aged 85 from a middle-sized city in the Netherlands: the Leiden 85-plus......) were included as geriatric giants. Participants provided a score for life satisfaction and were followed up for vital status. Concordance of self-rated health with physician-rated (k = .3 [.0]) and nurse-rated health (k = .2 [.0]) was low. All three ratings were associated with the geriatric giants...

Age Replacement and Service Rate Control of Stochastically Degrading Queues

National Research Council Canada - National Science Library

Chapin, Patrick

2004-01-01

This thesis considers the problem of optimally selecting a periodic replacement time for a multiserver queueing system in which each server is subject to degradation as a function of the mean service...

Life cycle and population growth rate of Caenorhabditis elegans studied by a new method.

Science.gov (United States)

Muschiol, Daniel; Schroeder, Fabian; Traunspurger, Walter

2009-05-16

The free-living nematode Caenorhabditis elegans is the predominant model organism in biological research, being used by a huge number of laboratories worldwide. Many researchers have evaluated life-history traits of C. elegans in investigations covering quite different aspects such as ecotoxicology, inbreeding depression and heterosis, dietary restriction/supplement, mutations, and ageing. Such traits include juvenile growth rates, age at sexual maturity, adult body size, age-specific fecundity/mortality, total reproduction, mean and maximum lifespan, and intrinsic population growth rates. However, we found that in life-cycle experiments care is needed regarding protocol design. Here, we test a recently developed method that overcomes some problems associated with traditional cultivation techniques. In this fast and yet precise approach, single individuals are maintained within hanging drops of semi-fluid culture medium, allowing the simultaneous investigation of various life-history traits at any desired degree of accuracy. Here, the life cycles of wild-type C. elegans strains N2 (Bristol, UK) and MY6 (Münster, Germany) were compared at 20 degrees C with 5 x 10(9) Escherichia coli ml-1 as food source. High-resolution life tables and fecundity schedules of the two strains are presented. Though isolated 700 km and 60 years apart from each other, the two strains barely differed in life-cycle parameters. For strain N2 (n = 69), the intrinsic rate of natural increase (r m d(-1)), calculated according to the Lotka equation, was 1.375, the net reproductive rate (R 0) 291, the mean generation time (T) 90 h, and the minimum generation time (T min) 73.0 h. The corresponding values for strain MY6 (n = 72) were r m = 1.460, R0 = 289, T = 84 h, and T min = 67.3 h. Peak egg-laying rates in both strains exceeded 140 eggs d(-1). Juvenile and early adulthood mortality was negligible. Strain N2 lived, on average, for 16.7 d, while strain MY6 died 2 days earlier; however

Life cycle and population growth rate of Caenorhabditis elegans studied by a new method

Directory of Open Access Journals (Sweden)

Schroeder Fabian

2009-05-01

Full Text Available Abstract Background The free-living nematode Caenorhabditis elegans is the predominant model organism in biological research, being used by a huge number of laboratories worldwide. Many researchers have evaluated life-history traits of C. elegans in investigations covering quite different aspects such as ecotoxicology, inbreeding depression and heterosis, dietary restriction/supplement, mutations, and ageing. Such traits include juvenile growth rates, age at sexual maturity, adult body size, age-specific fecundity/mortality, total reproduction, mean and maximum lifespan, and intrinsic population growth rates. However, we found that in life-cycle experiments care is needed regarding protocol design. Here, we test a recently developed method that overcomes some problems associated with traditional cultivation techniques. In this fast and yet precise approach, single individuals are maintained within hanging drops of semi-fluid culture medium, allowing the simultaneous investigation of various life-history traits at any desired degree of accuracy. Here, the life cycles of wild-type C. elegans strains N2 (Bristol, UK and MY6 (Münster, Germany were compared at 20°C with 5 × 109 Escherichia coli ml-1 as food source. Results High-resolution life tables and fecundity schedules of the two strains are presented. Though isolated 700 km and 60 years apart from each other, the two strains barely differed in life-cycle parameters. For strain N2 (n = 69, the intrinsic rate of natural increase (rmd-1, calculated according to the Lotka equation, was 1.375, the net reproductive rate (R0 291, the mean generation time (T 90 h, and the minimum generation time (Tmin 73.0 h. The corresponding values for strain MY6 (n = 72 were rm = 1.460, R0 = 289, T = 84 h, and Tmin = 67.3 h. Peak egg-laying rates in both strains exceeded 140 eggs d-1. Juvenile and early adulthood mortality was negligible. Strain N2 lived, on average, for 16.7 d, while strain MY6 died 2 days

Stability and Degradation of Polymer Solar cells

DEFF Research Database (Denmark)

Norrman, Kion

The current state-of-the-art allows for roll-to-roll manufacture of polymer solar cells in high volume with stability and efficiency sufficient to grant success in low-energy applications. However, further improvement is needed for the successful application of the devices in real life applications....... This is obtained by detailed knowledge of the degradation mechanisms. Methods to compare and standardize device stability are urgently needed. Methodologies to study failure mechanism that are based on physical processes (e.g. morphological changes) are well-established. However, methodologies to study chemical...... degradation mechanisms are currently scarce. An overview of known degradation mechanisms will be presented and discussed in relation to state-of-the-art methodologies to study failure mechanisms with focus on chemical degradation....

Improved constraints on in situ rates and on quantification of complete chloroethene degradation from stable carbon isotope mass balances in groundwater plumes

Science.gov (United States)

Höhener, Patrick; Elsner, Martin; Eisenmann, Heinrich; Atteia, Olivier

2015-11-01

Spills of chloroethenes (CEs) at industrial and urban sites can create groundwater plumes in which tetrachloro- and trichloroethene sequentially degrade to dichloroethenes, vinyl chloride (VC) and ethene, or ethane under reducing conditions. For detoxification, degradation must go beyond VC. Assessments based on ethene and ethane, however, are difficult because these products are volatile, may stem from alternative sources, can be further transformed and are not always monitored. To alternatively quantify degradation beyond VC, stable carbon isotope mass balances have been proposed where concentration-weighted CE isotope ratios are summed up and compared to the original source isotope ratio. Reported assessments, however, have provided not satisfactorily quantified results entailing greatly differing upper and lower estimates. This work proposes an integrative approach to better constrain the extent of total chloroethene degradation in groundwater samples. It is based on fitting of measured concentration and compound-specific stable carbon isotope data to an analytical reactive transport equation simulating steady-state plumes in two dimensions using an EXCEL spreadsheet. The fitting also yields estimates of degradation rates, of source width and of dispersivities. The approach is validated using two synthetic benchmark cases where the true extent of degradation is well known, and using data from two real field cases from literature.

Elucidating PID Degradation Mechanisms and In Situ Dark I-V Monitoring for Modeling Degradation Rate in CdTe Thin-Film Modules

DEFF Research Database (Denmark)

Hacke, Peter; Spataru, Sergiu; Johnston, Steve

2016-01-01

A progression of potential-induced degradation (PID) mechanisms are observed in CdTe modules, including shunting/junction degradation and two different manifestations of series resistance depending on the stress level and water ingress. The dark I-V method for in-situ characterization of Pmax bas...

On changing points of mean residual life and failure rate function for some generalized Weibull distributions

International Nuclear Information System (INIS)

Xie, M.; Goh, T.N.; Tang, Y.

2004-01-01

The failure rate function and mean residual life function are two important characteristics in reliability analysis. Although many papers have studied distributions with bathtub-shaped failure rate and their properties, few have focused on the underlying associations between the mean residual life and failure rate function of these distributions, especially with respect to their changing points. It is known that the change point for mean residual life can be much earlier than that of failure rate function. In fact, the failure rate function should be flat for a long period of time for a distribution to be useful in practice. When the difference between the change points is large, the flat portion tends to be longer. This paper investigates the change points and focuses on the difference of the changing points. The exponentiated Weibull, a modified Weibull, and an extended Weibull distribution, all with bathtub-shaped failure rate function will be used. Some other issues related to the flatness of the bathtub curve are discussed

Nanoscale zerovalent iron-mediated degradation of DDT in soil.

Science.gov (United States)

Han, Yuling; Shi, Nan; Wang, Huifang; Pan, Xiong; Fang, Hua; Yu, Yunlong

2016-04-01

Nanoscale zerovalent iron (nZVI)-mediated degradation of 1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (DDT) was investigated in a spiked soil under different conditions (iron sources, iron dosage, soil moisture, temperature, and soil types) and DDT-contaminated field. The degradation efficiency of p,p'-DDT by nZVI and nZVI coated with sodium oleate (SO-nZVI) was much higher than that by nZVI coated with polyimide (PI-nZVI). The rapid degradation of p,p'-DDT by nZVI only occurred in flooded soil. The degradation half-life of p,p'-DDT decreased significantly from 58.3 to 27.6 h with nZVI dosage from 0.5 to 2.0% and from 46.5 to 32.0 h with temperature from 15 to 35 °C. The degradation efficiency of p,p'-DDT by nZVI differed in Jinhua (JH), Jiaxing (JX), Xiaoshan (XS), Huajiachi (HJC), and Heilongjiang (HLJ) soils. A good correlation was found between the degradation half-life of p,p'-DDT and multiple soil properties. The probable nZVI-mediated degradation pathway of p,p'-DDT in soil was proposed as DDT → DDD/DDE → DDNS → DDOH based on the metabolites identified by GC-MS. The in situ degradation efficiency of residual DDTs in a contaminated field was profoundly enhanced by the addition of nZVI as compared to the control. It is concluded that nZVI might be an efficient agent for the remediation of DDT-contaminated soil under anaerobic environment.

An approach to nuclear-power-plant life management

International Nuclear Information System (INIS)

Vojvodic Tuma, J.; Celin, R.; Udovc, M.; Bundara, B.; Zabric, I.

2007-01-01

The plant life of a nuclear power plant (NPP) depends on degradation processes and ageing. Degradation is a deterioration phenomenon that can lead to component failure or limit the life of a component or the NPP itself. Ageing describes a continuous time or operational degradation of materials due to operational conditions, which include both normal and operating conditions. As a result of ageing degradation the state of the NPP or component can vary throughout the operating life. The degradation mechanisms for metallic components are general and local corrosion, erosion/corrosion, fatigue, corrosion fatigue, material changes due to irradiation and temperature, creep and wear. All the components of an NPP are subject to ageing, which may lead to the degradation of the physical barriers and redundant components, resulting in an increased probability of common-cause failures. The aims of NPP ageing management are to ensure that the necessary safety margins, adequate reliability and unforeseen and uncontrolled ageing of critical components do not shorten the NPP's lifetime. For the reasons stated above, plans are necessary to maintain the NPP in a state of high reliability. These are plans for an assessment of the life of the components that cannot be readily replaced, plans for operating life assessment or the planned replacement of major components where economic considerations will largely condition whether replacement or decommissioning should be pursued and plans for maintenance and replacements so that outages and delays can be minimised. In this paper some aspects of the process of NPP life management will be presented. (author)

Degradation of light emitting diodes: a proposed methodology

International Nuclear Information System (INIS)

Koh, Sau; Vam Driel, Willem; Zhang, G.Q.

2011-01-01

Due to their long lifetime and high efficacy, light emitting diodes have the potential to revolutionize the illumination industry. However, self heat and high environmental temperature which will lead to increased junction temperature and degradation due to electrical overstress can shorten the life of the light emitting diode. In this research, a methodology to investigate the degradation of the LED emitter has been proposed. The epoxy lens of the emitter can be modelled using simplified Eyring methods whereas an equation has been proposed for describing the degradation of the LED emitters. (semiconductor devices)

Degradation of multiwall carbon nanotubes by bacteria

International Nuclear Information System (INIS)

Zhang, Liwen; Petersen, Elijah J.; Habteselassie, Mussie Y.; Mao, Liang; Huang, Qingguo

2013-01-01

Understanding the environmental transformation of multiwall carbon nanotubes (MWCNTs) is important to their life cycle assessment and potential environmental impacts. We report that a bacterial community is capable of degrading 14 C-labeled MWCNTs into 14 CO 2 in the presence of an external carbon source via co-metabolism. Multiple intermediate products were detected, and genotypic characterization revealed three possible microbial degraders: Burkholderia kururiensis, Delftia acidovorans, and Stenotrophomonas maltophilia. This result suggests that microbe/MWCNTs interaction may impact the long-term fate of MWCNTs. Highlights: •Mineralization of MWCNTs by a bacterial community was observed. •The mineralization required an external carbon source. •Multiple intermediate products were identified in the MWCNT degrading culture. •Three bacterial species were found likely responsible for MWCNT degradation. -- The 14 C-labeled multiwall carbon nanotubes can be degraded to 14 CO 2 and other byproducts by a bacteria community under natural conditions

Structural insight into molecular mechanism of poly(ethylene terephthalate) degradation

OpenAIRE

Joo, Seongjoon; Cho, In Jin; Seo, Hogyun; Son, Hyeoncheol Francis; Sagong, Hye-Young; Shin, Tae Joo; Choi, So Young; Lee, Sang Yup; Kim, Kyung-Jin

2018-01-01

Plastics, including poly(ethylene terephthalate) (PET), possess many desirable characteristics and thus are widely used in daily life. However, non-biodegradability, once thought to be an advantage offered by plastics, is causing major environmental problem. Recently, a PET-degrading bacterium, Ideonella sakaiensis, was identified and suggested for possible use in degradation and/or recycling of PET. However, the molecular mechanism of PET degradation is not known. Here we report the crystal ...

Waste Handling Shaft concrete liner degradation conclusions and recommendations

International Nuclear Information System (INIS)

1992-10-01

The primary function of the Waste Handling Shaft (WHS) at the Waste Isolation Pilot Plant (WIPP) is to permit the transfer of radioactive waste from the surface waste handling building to the underground storage area. It also serves as an intake shaft for small volumes of air during normal storage operations and as an emergency escape route. Part of the construction was the placement of a concrete liner and steel reinforced key in 1984. During a routine shaft inspection in May 1990, some degradation of the WHS concrete liner was observed between the depths of 800 and 900 feet below the ground surface. Detailed investigations of the liner had been carried out by Sandia National Laboratories and by Westinghouse Electric Corporation Waste Isolation Division (WID) through Lankard Materials Laboratory. Observations, reports, and data support the conclusion that the concrete degradation, resulting from attack by chemically aggressive brine, is a localized phenomena. It is the opinion of the WID that the degradation is not considered an immediate or near term concern; this is supported by technical experts. WID recommendations have been made which, when implemented, will ensure an extended liner life. Based on the current assessment of available data and the proposed shaft liner monitoring program described in this report, it is reasonable to assume that the operational life of the concrete shaft liner can safely support the 25-year life of the WIPP. Analysis of data indicates that degradation of the shaft's concrete liner is attributed to chemically aggressive brine seeping through construction joints and shrinkage cracks from behind the liner in and around the 834-foot depth. Chemical and mechanical components of concrete degradation have been identified. Chemical attack is comprised of several stages of concrete alteration. The other component, mechanical degradation, results from the expansive forces of crystals forming in the concrete pore space

CONTROL OF DIMENSIONAL STABILITY AND DEGRADATION RATE IN ELECTROSPUN COMPOSITE SCAFFOLDS COMPOSED OF POLY(D,L-LACTIDE-CO-GLYCOLIDE)AND POLY(Ε-CAPROLACTONE)

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

The purpose of this study is to investigate the effect of composition poly(D,L-lactide-co-glycolide)/poly(ε-caprolactone)(PLGA/PCL)blending on the morphology,shrinkage and degradation behaviors of the electrospun fibers.With the increase of PLGA content in the composite fibers,the average diameter of the electrospun fibers increased from 1.35 μm to 1.95μm.The serious shrinking of the electrospun PLGA meshes could be circumvented by adding 20% PCL in the fibers,resulting from the semi-crystalline nature of PCL.The degradation rate of the electrospun meshes could be modulated by PLGA/PCL composition.In addition,the electrospun meshes containing 20% PCL displayed stable dimensional morphology with degradation.

Evaluation of the performance degradation at PAFC effect of electrolyte fill-level on electrode performance

Energy Technology Data Exchange (ETDEWEB)

Kitai, Takashi; Uchida, Hiroyuki; Watanabe, Masahiro [Yamanashi Univ., Kofu (Japan)] [and others

1996-12-31

As a complimentary research project to the demonstration project of 5MW and 1MW PAFC plants, the mechanism and rate of deterioration of the cells and stacks have been studied from 1995 FY, with the objective of establishing an estimation method for the service life-time of the cell stacks. This work has been performed in the Basic Research Project, as part of that project on PAFC`s, selecting four subjects (Electrocatalysts degradation, Electrolyte fill-level, Cell material corrosion, Electrolyte loss) as the essential factors relating to the life-time. In this report, we will exhibit the effect of the electrolyte fill-level on the electrode performances.

Assessment by HPLC of the degradation behavior of acitretin under hydrolytic, oxidative, photolytic and thermal stress conditions

Directory of Open Access Journals (Sweden)

Pawan K. Porwal

2014-12-01

Full Text Available Acitretin is a photosensitive oral retinoid with very limited data available on its degradation. The official HPLC method for acitretin determination was insufficient to resolve the degradation products generated during stability studies. Therefore, an isocratic RP-HPLC–UV method was developed for the determination of acitretin in the presence of its related impurities and degradation products. Efficient chromatographic separation was achieved on a Thermo beta-basic column C18 (100 mm×4.6 mm, 5 μm with mobile phase containing 0.3% (v/v glacial acetic acid with acetonitrile (ACN and isopropyl alcohol (IPA in an isocratic ratio of 70:30 at a flow rate of 1.0 mL/min with the eluent monitored at 360 nm. The method was validated for specificity, linearity, precision, accuracy and robustness. The calibration plot was linear over the concentration range of 50–150 μg/mL with a correlation coefficient (r2 of 0.999. The proposed method was used to investigate the degradation kinetics of acitretin under the different degradative conditions. The degradation rate constant (K, half-life (t1/2, and t90 were calculated. Degradation of acitretin followed pseudo-first-order kinetics. The drug was found to be less stable under acidic and photolytic degradation conditions: the photolytic degradation constants for acitretin in sunlight and UV light were 0.002698% and 0.0008402% min−1, respectively. The LOD for acitretin and the known impurities were at a level below 0.02%. The method shows consistent recoveries for ACTR (99.8%–101.2% and also for its known impurities (97.2–101.3%. The method was found to be accurate, precise, linear, specific, sensitive, rugged, robust, and useful for characterizing the stability of this chemical.

Life estimation I and C cable insulation materials based on accelerated life testing accelerated life testing

International Nuclear Information System (INIS)

Santhosh, T.V.; Ramteke, P.K.; Shrestha, N.B.; Ahirwar, A.K.; Gopika, V.

2016-01-01

Accelerated Iife tests are becoming increasingly popular in today's industry due to the need for obtaining life data quickly and reliably. Life testing of products under higher stress levels without introducing additional failure modes can provide significant savings of both time and money. Correct analysis of data gathered via such accelerated life testing will yield parameters and other information for the product's life under use stress conditions. To be of practical use in assessing the operational behaviour of cables in NPPs, laboratory ageing aims to mimic the type of degradation observed under operational conditions. Conditions of testing therefore need to be carefully chosen to ensure that the degradation mechanism occurring in the accelerated tests are similar to those which occur in service. This paper presents the results of an investigation in which the elongation-at-break (EAB) measurements were carried on a typical control cable to predict the mean life at service conditions. A low voltage polyvinyl chloride (PVC) insulated and PVC sheathed control cable, used in NPP instrumentation and control (I and C) applications, was subjected thermal ageing at three elevated temperatures

Damage Assessment Technologies for Prognostics and Proactive Management of Materials Degradation (PMMD)

International Nuclear Information System (INIS)

Bond, Leonard J.; Doctor, Steven R.; Griffin, Jeffrey W.; Hull, Amy B.; Malik, Shah

2009-01-01

performance start with the application of a stressor to the component. The design engineer sets the desired operational stressor intensity level so that the degradation in the physical state of the component occurs slowly enough for the equipment to last for its required design life. In general, when the design limit of a stressor is exceeded (during operation), the component life expectancy starts to shorten. Conversely, careful control of operational parameters can enable extension of component life beyond that normally expected. For systems which were conservatively designed (such as nuclear power plants), the premise of the prognostic methodology is that a relationship can be derived that will allow a much more accurate projection of the remaining useful life. This is achieved by focusing on trending the stressor characterics rather than trending a performance metric. In this trend analysis example, the slope of the trended parameter is thought to give a measure of the degradation rate of the component performance. This is assumed to be a function of the rate of decline in the physical integrity of the equipment. Experience from measurements has shown this assumption to be true if one accounts for the nonlinearity which can occur between physical attributes and their effects on performance.

Life Change Units (LCU Rating as Stressors in Iranian Hospitals’ Nurses

Directory of Open Access Journals (Sweden)

Hossein Dargahi

2012-02-01

Full Text Available Healthcare workers suffer from work-related or occupational stress. This can lead to severe distress, burnout or physical illness, and finally to decrease quality of work life and services provision. Nurses must be aware of retential stressors, because they add to the cumulative effect of other stressful events. Holmes and Rahe both found a relationship between life change unit as stressors and health changes. This research reported here aims to measure the life change units as stressors among Iranian Hospitals Nurses by LCU rating. A cross - sectional, descriptive and analytical study was conducted among 389 nurses working in 15 teaching hospitals in Tehran, Iran. The respondents were asked to select each of 54 events that cause stress ranked in order of their life change units developed by Holmes and Rahe as stress scale. Before beginning the main study, the reliability and coincidental validity was performed. All data were analyzed using SPSS for windows version 18, t-test, Anova statistical methods. Approximately, half of the nurses associated major mortgage, foreclosure of mortgage or loan. More than 50% of the Iranian nurses had 150-300 and more than 300 LCU rating which had the chance to expose to extremely serious risk to health.Iranian hospitals nurses suffer from stress that caused by Life Change Units organizational factors such as change in the financial state, change in the work environment and major mortgage. We recommend to Iranian nursing policy-makers to choose strategies to help nurses cope effectively with workplace stressors. Nursing managers and / or nursing management should develop strategies to address and improve the quality of working conditions for nurses in the hospitals. Providing educational and career prospects can contribute to decrease nurses occupational stress level, the maintaining their work ability.

Quantifying Protein Synthesis and Degradation in Arabidopsis by Dynamic 13CO2 Labeling and Analysis of Enrichment in Individual Amino Acids in Their Free Pools and in Protein1[OPEN

Science.gov (United States)

Fernie, Alisdair R.; Stitt, Mark

2015-01-01

Protein synthesis and degradation represent substantial costs during plant growth. To obtain a quantitative measure of the rate of protein synthesis and degradation, we supplied 13CO2 to intact Arabidopsis (Arabidopsis thaliana) Columbia-0 plants and analyzed enrichment in free amino acids and in amino acid residues in protein during a 24-h pulse and 4-d chase. While many free amino acids labeled slowly and incompletely, alanine showed a rapid rise in enrichment in the pulse and a decrease in the chase. Enrichment in free alanine was used to correct enrichment in alanine residues in protein and calculate the rate of protein synthesis. The latter was compared with the relative growth rate to estimate the rate of protein degradation. The relative growth rate was estimated from sequential determination of fresh weight, sequential images of rosette area, and labeling of glucose in the cell wall. In an 8-h photoperiod, protein synthesis and cell wall synthesis were 3-fold faster in the day than at night, protein degradation was slow (3%–4% d−1), and flux to growth and degradation resulted in a protein half-life of 3.5 d. In the starchless phosphoglucomutase mutant at night, protein synthesis was further decreased and protein degradation increased, while cell wall synthesis was totally inhibited, quantitatively accounting for the inhibition of growth in this mutant. We also investigated the rates of protein synthesis and degradation during leaf development, during growth at high temperature, and compared synthesis rates of Rubisco large and small subunits of in the light and dark. PMID:25810096

Probabilistic analysis of degradation incubation time of steam generator tubing materials

International Nuclear Information System (INIS)

Pandey, M.D.; Jyrkama, M.I.; Lu, Y.; Chi, L.

2012-01-01

The prediction of degradation free lifetime of steam generator (SG) tubing material is an important step in the life cycle management and decision for replacement of steam generators during the refurbishment of a nuclear station. Therefore, an extensive experimental research program has been undertaken by the Canadian Nuclear Industry to investigate the degradation of widely-used SG tubing alloys, namely, Alloy 600 TT, Alloy 690 TT, and Alloy 800. The corrosion related degradations of passive metals, such as pitting, crevice corrosion and stress corrosion cracking (SCC) etc. are assumed to start with the break down of the passive film at the tube-environment interface, which is characterized by the incubation time for passivity breakdown and then the degradation growth rate, and both are influenced by the chemical environment and coolant temperature. Since the incubation time and growth rate exhibit significant variability in the laboratory tests used to simulate these degradation processes, the use of probabilistic modeling is warranted. A pit is initiated with the breakdown of the passive film on the SG tubing surface. Upon exposure to aggressive environments, pitting corrosion may not initiate immediately, or may initiate and then re-passivate. The time required to initiate pitting corrosion is called the pitting incubation time, and that can be used to characterize the corrosion resistance of a material under specific test conditions. Pitting may be the precursor to other corrosion degradation mechanisms, such as environmentally-assisted cracking. This paper will provide an overview of the results of the first stage of experimental program in which samples of Alloy 600 TT, Alloy 690 TT, and Alloy 800 were tested under various temperatures and potentials and simulated crevice environments. The testing environment was chosen to represent layup, startup, and full operating conditions of the steam generators. Degradation incubation times for over 80 samples were

Quantifying protein synthesis and degradation in Arabidopsis by dynamic 13CO2 labeling and analysis of enrichment in individual amino acids in their free pools and in protein.

Science.gov (United States)

Ishihara, Hirofumi; Obata, Toshihiro; Sulpice, Ronan; Fernie, Alisdair R; Stitt, Mark

2015-05-01

Protein synthesis and degradation represent substantial costs during plant growth. To obtain a quantitative measure of the rate of protein synthesis and degradation, we supplied (13)CO2 to intact Arabidopsis (Arabidopsis thaliana) Columbia-0 plants and analyzed enrichment in free amino acids and in amino acid residues in protein during a 24-h pulse and 4-d chase. While many free amino acids labeled slowly and incompletely, alanine showed a rapid rise in enrichment in the pulse and a decrease in the chase. Enrichment in free alanine was used to correct enrichment in alanine residues in protein and calculate the rate of protein synthesis. The latter was compared with the relative growth rate to estimate the rate of protein degradation. The relative growth rate was estimated from sequential determination of fresh weight, sequential images of rosette area, and labeling of glucose in the cell wall. In an 8-h photoperiod, protein synthesis and cell wall synthesis were 3-fold faster in the day than at night, protein degradation was slow (3%-4% d(-1)), and flux to growth and degradation resulted in a protein half-life of 3.5 d. In the starchless phosphoglucomutase mutant at night, protein synthesis was further decreased and protein degradation increased, while cell wall synthesis was totally inhibited, quantitatively accounting for the inhibition of growth in this mutant. We also investigated the rates of protein synthesis and degradation during leaf development, during growth at high temperature, and compared synthesis rates of Rubisco large and small subunits of in the light and dark. © 2015 American Society of Plant Biologists. All Rights Reserved.

THE EFFECT OF VOLTAGE ON ELECTROCHEMICAL DEGRADATION OF TRICHLOROETHYLENE

Science.gov (United States)

This study investigates electrochemical degradation of Trichloroethylene (TCE) using granular graphite as electrodes in a flow-through reactor system. The experiments were conducted to obtain information on the effect of voltage and flow rates on the degradation rates of TCE. The...

Metagenomic Functional Potential Predicts Degradation Rates of a Model Organophosphorus Xenobiotic in Pesticide Contaminated Soils

Directory of Open Access Journals (Sweden)

Thomas C. Jeffries

2018-02-01

Full Text Available Chemical contamination of natural and agricultural habitats is an increasing global problem and a major threat to sustainability and human health. Organophosphorus (OP compounds are one major class of contaminant and can undergo microbial degradation, however, no studies have applied system-wide ecogenomic tools to investigate OP degradation or use metagenomics to understand the underlying mechanisms of biodegradation in situ and predict degradation potential. Thus, there is a lack of knowledge regarding the functional genes and genomic potential underpinning degradation and community responses to contamination. Here we address this knowledge gap by performing shotgun sequencing of community DNA from agricultural soils with a history of pesticide usage and profiling shifts in functional genes and microbial taxa abundance. Our results showed two distinct groups of soils defined by differing functional and taxonomic profiles. Degradation assays suggested that these groups corresponded to the organophosphorus degradation potential of soils, with the fastest degrading community being defined by increases in transport and nutrient cycling pathways and enzymes potentially involved in phosphorus metabolism. This was against a backdrop of taxonomic community shifts potentially related to contamination adaptation and reflecting the legacy of exposure. Overall our results highlight the value of using holistic system-wide metagenomic approaches as a tool to predict microbial degradation in the context of the ecology of contaminated habitats.

Enzyme kinetics and identification of the rate-limiting step of enzymatic arabinoxylan degradation

DEFF Research Database (Denmark)

Rasmussen, Louise Enggaard; Xu, Cheng; Sørensen, Jens

2012-01-01

This study investigated the kinetics of multi-enzymatic degradation of soluble wheat arabinoxylan by monitoring the release of xylose and arabinose during designed treatments with mono-component enzymes at different substrate concentrations. The results of different combinations of α...... α-l-arabinofuranosidases catalyze liberation of arabinose residues linked 1→3 to singly (AFAn) or doubly (AFBa) substituted xyloses in arabinoxylan, respectively. When added to arabinoxylan at equimolar levels, the AFBa enzyme catalyzed the release of more arabinose, i.e. had a higher rate constant...... than AFAn, but with respect to the xylose release, AFAn – as expected – exhibited a better synergistic effect than AFBa with β-xylosidase. This synergistic effect with AFAn was estimated to increase the number of β-xylosidase catalyzed cuts from ∼3 (with β-xylosidase alone) to ∼7 in each arabinoxylan...

Service-life prediction of reinforced concrete structures in subsurface environment

Energy Technology Data Exchange (ETDEWEB)

Kwon, Ki Jung; Jung, Hae Ryong; Park, Joo Wan [Korea Radioactive Waste Agency, Daejeon (Korea, Republic of)

2016-03-15

This paper focuses on the estimation of durability and service-life of reinforced concrete structures in Wolsong Low- and intermediate-level wastes Disposal Center (WLDC) in Korea. There are six disposal silos located in the saturated environment. The silo concrete is degraded due to reactions with groundwater and chemical attacks, and finally it will lose its properties as a transport barrier. The infiltration of sulfate and magnesium, leaching of potassium hydroxide, and chlorine induced corrosion are the most significant factors for degradation of reinforced concrete structure in underground environment. From the result of evaluation of the degradation time for each factor, the degradation rate of the reinforced concrete due to sulfate and magnesium is 1.308×10{sup -3} cm/yr, and it is estimated to take 48,000 years for full degradation while potassium hydroxide is leached in depth of less than 1.5 cm at 1,000 years after the initiation of degradation. In case of chlorine induced corrosion, it takes 1,648 years to initiate corrosion in the main reinforced bar and 2,288 years to reach the lifetime limit of the structural integrity, and thus it is evaluated as the most significant factor.

Reference values for respiratory rate in the first 3 years of life.

Science.gov (United States)

Rusconi, F; Castagneto, M; Gagliardi, L; Leo, G; Pellegatta, A; Porta, N; Razon, S; Braga, M

1994-09-01

Raised respiratory rate is a useful sign to diagnose lower respiratory infections in childhood. However, the normal range for respiratory rate has not been defined in a proper, large sample. To assess the respiratory rate in a large number of infants and young children in order to construct percentile curves by age; to determine the repeatability to the assessment using a stethoscope and compare it with observation. Respiratory rate was recorded for 1 minute with a stethoscope in 618 infants and children, aged 15 days to 3 years old, without respiratory infections or any other severe disease when awake and calm and when asleep. In 50 subjects we compared respiratory rate taken 30 to 60 minutes apart to assess repeatability, and in 50 others we compared simultaneous counts obtained by stethoscope versus observation. Repeatability was good as the standard deviation of differences was 2.5 breaths/minute in awake and 1.7 breaths/minute in asleep children. Respiratory rate obtained with a stethoscope was systematically higher than that obtained by observation (mean difference 2.6 breaths/minute in awake and 1.8 breaths/minute in asleep children; P = .015 and P respiratory rate with age was seen for both states, and it was faster in the first few months of life when also a greater dispersion of values was observed. A second degree polynomial curve accurately fitted the data. Reference percentile values were developed from these data. The repeatability of respiratory rate measured with a stethoscope was good. Percentile curves would be particularly helpful in the first months of life when the decline in respiratory rate is very rapid and prevents to use cut off values for defining "normality."

Thermal degradation process of poly (alpha-methylstyrene) microspheres coated with glow discharge polymer

International Nuclear Information System (INIS)

Zhang Zhanwen; Huang Yong; Tang Yongjian; Li Bo; Chen Sufen; He Zhibing

2009-01-01

Glow discharge polymer (GDP) shell was made by the decomposable mandrel technique using poly(alpha-methylstyrene) (PAMS) mandrel. The PAMS degradation rate and the GDP shell surface morphology at different equilibrium temperatures were investigated. Degradation rate was calculated from weight variation of PAMS before and after pyrolysis process. Experiment results indicate that the degradation rate decreases at the fixed equilibrium temperature and graded temperature can improve the rate. The degradation process has an effect on the GDP shell properties. The PAMS doesn't molten to flow liquid during degradation. But the degradation can reduce surface finish of GDP coatings. The GDP shell deffects are the result of the PAMS degradiation process. (authors)

Rumen degradation characteristics of ryegrass herbage and ryegrass silage are affected by interactions between stage of maturity and nitrogen fertilisation rate

NARCIS (Netherlands)

Heeren, J.A.H.; Podesta, S.C.; Hatew, B.; Klop, G.; Laar, van H.; Bannink, A.; Warner, D.; Jonge, de L.H.; Dijkstra, J.

2014-01-01

The objective of this experiment was to evaluate interaction effects between stage of maturity and N fertilization rate on rumen degradation characteristics determined with nylon bag incubations of ryegrass herbages and ryegrass silage. Grass herbage (n = 4) was cut after 3 or 5 weeks of regrowth

On the change points of mean residual life and failure rate functions for some generalized gamma type distributions

Directory of Open Access Journals (Sweden)

Parsa M.

2014-01-01

Full Text Available Mean residual life and failure rate functions are ubiquitously employed in reliability analysis. The term of useful period of lifetime distributions of bathtub-shaped failure rate functions is referred to the flat rigion of this function and has attracted authors and researchers in reliability, actuary, and survival analysis. In recent years, considering the change points of mean residual life and failure rate functions has been extensively utelized in determining the optimum burn-in time. In this paper we investigate the difference between the change points of failure rate and mean residual life functions of some generalized gamma type distributions due to the capability of these distributions in modeling various bathtub-shaped failure rate functions.

Degradation Prediction Model Based on a Neural Network with Dynamic Windows

Science.gov (United States)

Zhang, Xinghui; Xiao, Lei; Kang, Jianshe

2015-01-01

Tracking degradation of mechanical components is very critical for effective maintenance decision making. Remaining useful life (RUL) estimation is a widely used form of degradation prediction. RUL prediction methods when enough run-to-failure condition monitoring data can be used have been fully researched, but for some high reliability components, it is very difficult to collect run-to-failure condition monitoring data, i.e., from normal to failure. Only a certain number of condition indicators in certain period can be used to estimate RUL. In addition, some existing prediction methods have problems which block RUL estimation due to poor extrapolability. The predicted value converges to a certain constant or fluctuates in certain range. Moreover, the fluctuant condition features also have bad effects on prediction. In order to solve these dilemmas, this paper proposes a RUL prediction model based on neural network with dynamic windows. This model mainly consists of three steps: window size determination by increasing rate, change point detection and rolling prediction. The proposed method has two dominant strengths. One is that the proposed approach does not need to assume the degradation trajectory is subject to a certain distribution. The other is it can adapt to variation of degradation indicators which greatly benefits RUL prediction. Finally, the performance of the proposed RUL prediction model is validated by real field data and simulation data. PMID:25806873

Solubility and degradation of paracetamol in subcritical water

Directory of Open Access Journals (Sweden)

Emire Zuhal

2017-01-01

Full Text Available In this study, solubility and degradation of paracetamol were examined using subcritical water. Effect of temperature and static time was investigated during solubility process in subcritical water at constant pressure (50 bar. Experimental results show that temperature and static time have crucial effect on the degradation and solubility rates. Maximum mole fraction for solubility of paracetamol was obtained at 403 K as (14.68 ± 0.74×103. Approximation model for solubility of paracetamol was proposed. O2 and H2O2 were used in degradation process of paracetamol. Maximum degradation rate was found as 68.66 ± 1.05 and 100 ± 0.00 % using O2 and H2O2, respectively.

Degradation and toxicity of phenyltin compounds in soil

International Nuclear Information System (INIS)

Paton, G.I.; Cheewasedtham, W.; Marr, I.L.; Dawson, J.J.C.

2006-01-01

Although the fate of organotins has been widely studied in the marine environment, fewer studies have considered their impact in terrestrial systems. The degradation and toxicity of triphenyltin in autoclaved, autoclaved-reinoculated and non-sterilised soil was studied in a 231 day incubation experiment following a single application. Degradation and toxicity of phenyltin compounds in soil was monitored using both chemical and microbial (lux-based bacterial biosensors) methods. Degradation was significantly slower in the sterile soil when compared to non-sterilised soils. In the non-sterilised treatment, the half-life of triphenyltin was 27 and 33 days at amendments of 10 and 20 mg Sn kg -1 , respectively. As initial triphenyltin degradation occurred, there was a commensurate increase in toxicity, reflecting the fact that metabolites produced may be both more bioavailable and toxic to the target receptor. Over time, the toxicity reduced as degradation proceeded. The toxicity impact on non-target receptors for these compounds may be significant. - Triphenyltin degradative metabolites cause toxic responses to biosensors

Potent heme-degrading action of antimony and antimony-containing parasiticidal agents.

Science.gov (United States)

Drummond, G S; Kappas, A

1981-02-01

The ability of antimony and antimony-containing parasiticidal agents to enhance the rate of heme degradation in liver and kidney was investigated. Trivalent antimony was shown to be an extremely potent inducer of heme oxygenase, the initial and rate-limiting enzyme in heme degradation, in both organs, whereas the pentavalent form was a weak inducer of this enzyme. The ability of antimony to induce heme oxygenase was dose-dependent, independent of the salt used, and not a result of a direct activation of the enzyme in vitro. Concomitant with heme oxygenase induction by antimony, microsomal heme and cytochrome P-450 contents decreased, the cyto-chrome P-450-dependent mixed function oxidase system was impaired, and delta-ami-nolevulinate synthase (ALAS), the rate-limiting enzyme of heme synthesis, underwent the sequential changes-initial inhibition followed by rebound induction-usually associated with the administration of transition elements such as cobalt. Antimony induction of heme oxygenase however, unlike the enzyme induction elicited by cobalt, was not prevented either by cysteine administered orally or as a cysteine metal complex, or by simultaneous zinc administration. Desferoxamine also did not block heme oxygenase induction by antimony, but this chelator did prevent the rebound increase in ALAS activity associated with antimony or cobalt treatment. Antimony-containing parasiticidal drugs were also potent inducers of heme oxygenase in liver and kidney. The heme degradative action of these drugs may be related in part to the jaundice commonly associated with the prolonged therapeutic use of these agents. The heme-oxygenase-inducing action of antimony-containing parasiticidal drugs is a newly defined biological property of these compounds. The relation between the parasiticidal and the heme-oxygenase-inducing actions of such drugs is unknown. However, certain parasites contain hemoproteins or require heme compounds during their life cycle. It may therefore be

Evaluation of an in vitro faecal degradation method for early assessment of the impact of colonic degradation on colonic absorption in humans.

Science.gov (United States)

Tannergren, Christer; Borde, Anders; Boreström, Cecilia; Abrahamsson, Bertil; Lindahl, Anders

2014-06-16

The objective of this study was to develop and evaluate an in vitro method to investigate bacterial-mediated luminal degradation of drugs in colon in humans. This would be a valuable tool for the assessment of drug candidates during early drug development, especially for compounds intended to be developed as oral extended release formulations. Freshly prepared faecal homogenate from healthy human volunteers (n=3-18), dog (n=6) and rat (colon and caecal content, n=3) was homogenised with 3.8 parts (w/w) physiological saline under anaerobical conditions. Four model compounds (almokalant, budesonide, ximelagatran and metoprolol) were then incubated (n=3-18) separately in the human faecal homogenate for up to 120min at 37°C. In addition, ximelagatran was also incubated in the faecal or colonic content from dog and rat. The mean (±SD) in vitro half-life for almokalant, budesonide and ximelagatran was 39±1, 68±21 and 26±12min, respectively, in the human faecal homogenate. Metoprolol was found to be stable in the in vitro model. The in vitro degradation data was then compared to literature data on fraction absorbed after direct colon administration in humans. The percentage of drug remaining after 60min of in vitro incubation correlated (R(2)=0.90) with the fraction absorbed from colon in humans. The mean in vitro half-life of ximelagatran was similar in human faeces (26±12min) and rat colon content (34±31min), but significantly (pdegradation in vivo was rapidly degraded in the faecal homogenates as well as quantitatively since a correlation was established between percentage degraded in vitro at 60min and fraction absorbed in the colon for the model drugs, which have no other absorption limiting properties. Also, the method is easy to use from a technical point of view, which suggests that the method is suitable for use in early assessment of colonic absorption of extended release formulation candidates. Further improvement of the confidence in the use of the

Impact of composting strategies on the degradation of nonylphenol in sewage sludge.

Science.gov (United States)

Zheng, Guodi; Chen, Tongbin; Yu, Jie; Gao, Ding; Shen, Yujun; Niu, Mingjie; Liu, Hongtao

2015-12-01

Nonylphenol can be present in sewage sludge, and this can limit the use of the sewage sludge to amend soil. Composting is one of the most efficient and economical methods of making sewage sludge stable and harmless. The nonylphenol degradation rates during composting with added bulking agents and with aeration applied were studied. Three organic bulking agents (sawdust, corn stalk, and mushroom residue) were added to sewage sludge, and the effects of the bulking agents used and the amount added on nonylphenol degradation were determined. The highest apparent nonylphenol degradation rate (71.6%) was found for sewage sludge containing 20% mushroom residue. The lowest apparent nonylphenol degradation rate (22.5%) was found for sewage sludge containing 20% sawdust. The temperature of the composting pile of sewage sludge containing 20% sawdust became too high for nonylphenol to be efficiently degraded, and the apparent nonylphenol degradation rate was lower than was found for sewage sludge containing 10% sawdust. Increasing the ventilating time from 5 to 15 min increased the apparent nonylphenol degradation rate from 19.7 to 41.6%. Using appropriate aerobic conditions facilitates the degradation of nonylphenol in sewage sludge, decreasing the risks posed by sewage sludge applied to land. Adding too much of a bulking agent can decrease the amount of the nonylphenol degraded. Increasing the ventilating time and the amount of air supplied can increase the amount of nonylphenol degraded even if doing so causes the composting pile temperature to remain low.

Radiation induced degradation of xanthan gum in aqueous solution

Science.gov (United States)

Hayrabolulu, Hande; Demeter, Maria; Cutrubinis, Mihalis; Güven, Olgun; Şen, Murat

2018-03-01

In our previous study, we have investigated the effect of gamma rays on xanthan gum in the solid state and it was determined that dose rate was an important factor effecting the radiation degradation of xanthan gum. In the present study, in order to provide a better understanding of how ionizing radiation effect xanthan gum, we have investigated the effects of ionizing radiation on aqueous solutions of xanthan at various concentrations (0.5-4%). Xanthan solutions were irradiated with gamma rays in air, at ambient temperature, at different dose rates (0.1-3.3-7.0 kGy/h) and doses (2.5-50 kGy). Change in their molecular weights was followed by size exclusion chromatography (SEC). Chain scission yield (G(S)), and degradation rate constants (k) were calculated. It was determined that, solution concentration was a factor effecting the degradation chemical yield and degradation rate of xanthan gum. Chain scission reactions were more effective for lower solution concentrations.

Cellular metabolic rate is influenced by life-history traits in tropical and temperate birds.

Science.gov (United States)

Jimenez, Ana Gabriela; Van Brocklyn, James; Wortman, Matthew; Williams, Joseph B

2014-01-01

In general, tropical birds have a "slow pace of life," lower rates of whole-animal metabolism and higher survival rates, than temperate species. A fundamental challenge facing physiological ecologists is the understanding of how variation in life-history at the whole-organism level might be linked to cellular function. Because tropical birds have lower rates of whole-animal metabolism, we hypothesized that cells from tropical species would also have lower rates of cellular metabolism than cells from temperate species of similar body size and common phylogenetic history. We cultured primary dermal fibroblasts from 17 tropical and 17 temperate phylogenetically-paired species of birds in a common nutritive and thermal environment and then examined basal, uncoupled, and non-mitochondrial cellular O2 consumption (OCR), proton leak, and anaerobic glycolysis (extracellular acidification rates [ECAR]), using an XF24 Seahorse Analyzer. We found that multiple measures of metabolism in cells from tropical birds were significantly lower than their temperate counterparts. Basal and uncoupled cellular metabolism were 29% and 35% lower in cells from tropical birds, respectively, a decrease closely aligned with differences in whole-animal metabolism between tropical and temperate birds. Proton leak was significantly lower in cells from tropical birds compared with cells from temperate birds. Our results offer compelling evidence that whole-animal metabolism is linked to cellular respiration as a function of an animal's life-history evolution. These findings are consistent with the idea that natural selection has uniquely fashioned cells of long-lived tropical bird species to have lower rates of metabolism than cells from shorter-lived temperate species.

Cellular metabolic rate is influenced by life-history traits in tropical and temperate birds.

Directory of Open Access Journals (Sweden)

Ana Gabriela Jimenez

Full Text Available In general, tropical birds have a "slow pace of life," lower rates of whole-animal metabolism and higher survival rates, than temperate species. A fundamental challenge facing physiological ecologists is the understanding of how variation in life-history at the whole-organism level might be linked to cellular function. Because tropical birds have lower rates of whole-animal metabolism, we hypothesized that cells from tropical species would also have lower rates of cellular metabolism than cells from temperate species of similar body size and common phylogenetic history. We cultured primary dermal fibroblasts from 17 tropical and 17 temperate phylogenetically-paired species of birds in a common nutritive and thermal environment and then examined basal, uncoupled, and non-mitochondrial cellular O2 consumption (OCR, proton leak, and anaerobic glycolysis (extracellular acidification rates [ECAR], using an XF24 Seahorse Analyzer. We found that multiple measures of metabolism in cells from tropical birds were significantly lower than their temperate counterparts. Basal and uncoupled cellular metabolism were 29% and 35% lower in cells from tropical birds, respectively, a decrease closely aligned with differences in whole-animal metabolism between tropical and temperate birds. Proton leak was significantly lower in cells from tropical birds compared with cells from temperate birds. Our results offer compelling evidence that whole-animal metabolism is linked to cellular respiration as a function of an animal's life-history evolution. These findings are consistent with the idea that natural selection has uniquely fashioned cells of long-lived tropical bird species to have lower rates of metabolism than cells from shorter-lived temperate species.

High-power UV-LED degradation: Continuous and cycled working condition influence

Science.gov (United States)

Arques-Orobon, F. J.; Nuñez, N.; Vazquez, M.; Segura-Antunez, C.; González-Posadas, V.

2015-09-01

High-power (HP) UV-LEDs can replace UV lamps for real-time fluoro-sensing applications by allowing portable and autonomous systems. However, HP UV-LEDs are not a mature technology, and there are still open issues regarding their performance evolution over time. This paper presents a reliability study of 3 W UV-LEDs, with special focus on LED degradation for two working conditions: continuous and cycled (30 s ON and 30 s OFF). Accelerated life tests are developed to evaluate the influence of temperature and electrical working conditions in high-power LEDs degradation, being the predominant failure mechanism the degradation of the package. An analysis that includes dynamic thermal and optical HP UV-LED measurements has been performed. Static thermal and stress simulation analysis with the finite element method (FEM) identifies the causes of package degradation. Accelerated life test results prove that HP UV-LEDs working in cycled condition have a better performance than those working in continuous condition.

Surface photo-discoloration and degradation of dyed wood veneer exposed to different wavelengths of artificial light

Energy Technology Data Exchange (ETDEWEB)

Liu, Yi [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Forest Products Development Center, School of Forestry and Wildlife Sciences, Auburn University, Auburn, AL 36830 (United States); Shao, Lingmin [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Gao, Jianmin, E-mail: jmgao@bjfu.edu.cn [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Guo, Hongwu, E-mail: hwg5052@163.com [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Chen, Yao [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Cheng, Qingzheng; Via, Brian K. [Forest Products Development Center, School of Forestry and Wildlife Sciences, Auburn University, Auburn, AL 36830 (United States)

2015-03-15

Highlights: • Investigate the selective absorption of different wavelengths of UV–vis light by dyed wood chromophores. • Identify connection between light wavelengths and surface color changes and chemical structure degradation. • Study hypochromic effect based on surface reflectance and K/S absorption changes during UV–vis irradiation. - Abstract: The surface of dyed wood is prone to discoloration when exposed to light irradiation which significantly decreases its decorative effect and shortens its service life. The influence of light wavelength exposure to the surface of dyed wood was investigated to study the effect on discoloration and degradation. Acid Blue V and Acid Red GR dyed wood veneers were subjected to light exposure with different wavelengths from the UV to visible region (254–420 nm). Results showed that the surface discoloration of dyed wood was linearly related to lignin concentration and dyes degradation and the consequent transformation of chromophoric groups such as aromatic (C=C) and carbonyl (C=O) through methoxy reaction. The dyes, lignin and some active constituents were degraded severely, even at short exposures. Acid Blue V dyed wood exhibited greater discoloration than the Acid Red GR treatment. The reflectance and K/S absorption curve showed a hypochromic effect on the dyed wood surface. The dyes and wood chemical structure played a complex and combined role on the selective absorption of different wavelengths of light. The color change rate was apparent with 254 nm exposure in the initial stages, but a greater discoloration rate occurred on the samples irradiated at 313 and 340 nm than at 254 and 420 nm with the time prolonged. The degradation rate and degree of discoloration correlated well with the light energy and wavelength.

Studies on degradation of chlorinated aromatic hydrocarbon by ...

African Journals Online (AJOL)

SERVER

2007-06-04

Jun 4, 2007 ... chlorobenzene to study the kinetics of degradation of chlorobenzene. The rate of decomposition of ... hydraulic fluids, biocides, herbicides, plastics, degree- ..... degradation by bacteria isolated from contaminated groundwater.

An empirical model to describe performance degradation for warranty abuse detection in portable electronics

International Nuclear Information System (INIS)

Oh, Hyunseok; Choi, Seunghyuk; Kim, Keunsu; Youn, Byeng D.; Pecht, Michael

2015-01-01

Portable electronics makers have introduced liquid damage indicators (LDIs) into their products to detect warranty abuse caused by water damage. However, under certain conditions, these indicators can exhibit inconsistencies in detecting liquid damage. This study is motivated by the fact that the reliability of LDIs in portable electronics is suspected. In this paper, first, the scheme of life tests is devised for LDIs in conjunction with a robust color classification rule. Second, a degradation model is proposed by considering the two physical mechanisms—(1) phase change from vapor to water and (2) water transport in the porous paper—for LDIs. Finally, the degradation model is validated with additional tests using actual smartphone sets subjected to the thermal cycling of −15 °C to 25 °C and the relative humidity of 95%. By employing the innovative life testing scheme and the novel performance degradation model, it is expected that the performance of LDIs for a particular application can be assessed quickly and accurately. - Highlights: • Devise an efficient scheme of life testing for a warranty abuse detector in portable electronics. • Develop a performance degradation model for the warranty abuse detector used in portable electronics. • Validate the performance degradation model with life tests of actual smartphone sets. • Help make a decision on warranty service in portable electronics manufacturers

In-situ degradation of sulphur mustard using (1R)-(-)-(camphorylsulphonyl) oxaziridine impregnated adsorbents

Energy Technology Data Exchange (ETDEWEB)

Sharma, Abha, E-mail: abha_052002@yahoo.co.in [Industrial Toxicology Research Centre, Mahatam Gandhi Marg, Lucknow, UP (India); Saxena, Amit; Singh, Beer [Defence Research and Development Establishment, Jhansi Road, Gwalior, MP (India)

2009-12-30

Bis-2-chloroethyl sulphide (sulphur mustard or HD) is an extremely toxic and persistent chemical warfare agent. For in-situ degradation of HD and its analogues (simulants), i.e., dibutyl sulphide (DBS) and ethyl 2-hydroxyethyl sulphide (HEES), different adsorbents systems loaded with (1R)-(-)-(camphorylsulphonyl) oxaziridine were prepared. Solution of sulphur mustard and its simulants was prepared in carbon tetrachloride and taken for uniform adsorption on the impregnated systems using incipient volume. Degradation kinetics monitored by GC/FID were found to be first-order. The half-life of degradation reactions for simulants was obtained in less than 30 and for HD in 120 min. From the studied kinetics it was observed that reaction was very rapid with simulants and decreased rate was found for HD. The order of reactivity of MgO/Oxa system for HD and simulants was found to be DBS > HEES > HD. Reaction products of the oxidation reaction of simulants and HD on adsorbents were extracted in dichloromethane and analysed by GC-MS. The products were found to be non-toxic sulphoxide. The objective of the study is to develop a reactive adsorbent for in-situ degradation of sulphur mustard which could be used in nuclear biological and chemical (NBC) filtration systems.

Data-driven remaining useful life prognosis techniques stochastic models, methods and applications

CERN Document Server

Si, Xiao-Sheng; Hu, Chang-Hua

2017-01-01

This book introduces data-driven remaining useful life prognosis techniques, and shows how to utilize the condition monitoring data to predict the remaining useful life of stochastic degrading systems and to schedule maintenance and logistics plans. It is also the first book that describes the basic data-driven remaining useful life prognosis theory systematically and in detail. The emphasis of the book is on the stochastic models, methods and applications employed in remaining useful life prognosis. It includes a wealth of degradation monitoring experiment data, practical prognosis methods for remaining useful life in various cases, and a series of applications incorporated into prognostic information in decision-making, such as maintenance-related decisions and ordering spare parts. It also highlights the latest advances in data-driven remaining useful life prognosis techniques, especially in the contexts of adaptive prognosis for linear stochastic degrading systems, nonlinear degradation modeling based pro...

Material degradation - a nuclear utility's view

International Nuclear Information System (INIS)

Spekkens, P.

2007-01-01

Degradation of nuclear plant materials has been responsible for major costs and unit outage time. As such, nuclear utilities are important end users of the information produced by R and D on material degradation. This plenary describes the significance of material degradation for the nuclear utilities, and how utilities use information about material degradation in their short, medium and long term planning activities. Utilities invest in R and D programs to assist them in their business objective of operating safely, reliably and cost competitively. Material degradation impacts all three of these business drivers. Utilities make decisions on life cycle planning, unit refurbishment and 'new build' projects on the basis of their understanding of the behaviour of a variety of materials in a broad range of environments. The R and D being carried out today will determine the future business success of the nuclear utilities. The R and D program needs to be broadly based to include a range of materials, environments and time-frames, particularly any new materials proposed for use in new units. The R and D community needs to help the utility managers make choices that will result in an optimized materials R and D program

Thermal Degradation of Lead Monoxide Filled Polymer Composite Radiation Shields

International Nuclear Information System (INIS)

Harish, V.; Nagaiah, N.

2011-01-01

Lead monoxide filled Isophthalate resin particulate polymer composites were prepared with different filler concentrations and investigated for physical, thermal, mechanical and gamma radiation shielding characteristics. This paper discusses about the thermo gravimetric analysis of the composites done to understand their thermal properties especially the effect of filler concentration on the thermal stability and degradation rate of composites. Pristine polymer exhibits single stage degradation whereas filled composites exhibit two stage degradation processes. Further, the IDT values as well as degradation rates decrease with the increased filler content in the composite.

Thermolysin damages animal life through degradation of plasma proteins enhanced by rapid cleavage of serpins and activation of proteases.

Science.gov (United States)

Kong, Lulu; Lu, Anrui; Guan, Jingmin; Yang, Bing; Li, Muwang; Hillyer, Julián F; Ramarao, Nalini; Söderhäll, Kenneth; Liu, Chaoliang; Ling, Erjun

2015-01-01

Thermolysin, a metallopeptidase secreted by pathogenic microbes, is concluded as an important virulence factor due to cleaving purified host proteins in vitro. Using the silkworm Bombyx mori as a model system, we found that thermolysin injection into larvae induces the destruction of the coagulation response and the activation of hemolymph melanization, which results in larval death. Thermolysin triggers the rapid degradation of insect and mammalian plasma proteins at a level that is considerably greater than expected in vitro and/or in vivo. To more specifically explore the mechanism, thermolysin-induced changes to key proteins belonging to the insect melanization pathway were assessed as a window for observing plasma protein cleavage. The application of thermolysin induced the rapid cleavage of the melanization negative regulator serpin-3, but did not directly activate the melanization rate-limiting enzyme prophenoloxidase (PPO) or the terminal serine proteases responsible for PPO activation. Terminal serine proteases of melanization are activated indirectly after thermolysin exposure. We hypothesize that thermolysin induces the rapid degradation of serpins and the activation of proteases directly or indirectly, boosting uncontrolled plasma protein degradation in insects and mammalians. © 2014 Wiley Periodicals, Inc.

Physiological underpinnings associated with differences in pace of life and metabolic rate in north temperate and neotropical birds.

Science.gov (United States)

Jimenez, Ana Gabriela; Cooper-Mullin, Clara; Calhoon, Elisabeth A; Williams, Joseph B

2014-07-01

Animal life-history traits fall within limited ecological space with animals that have high reproductive rates having short lives, a continuum referred to as a "slow-fast" life-history axis. Animals of the same body mass at the slow end of the life-history continuum are characterized by low annual reproductive output and low mortality rate, such as is found in many tropical birds, whereas at the fast end, rates of reproduction and mortality are high, as in temperate birds. These differences in life-history traits are thought to result from trade-offs between investment in reproduction or self-maintenance as mediated by the biotic and abiotic environment. Thus, tropical and temperate birds provide a unique system to examine physiological consequences of life-history trade-offs at opposing ends of the "pace of life" spectrum. We have explored the implications of these trade-offs at several levels of physiological organization including whole-animal, organ systems, and cells. Tropical birds tend to have higher survival, slower growth, lower rates of whole-animal basal metabolic rate and peak metabolic rate, and smaller metabolically active organs compared with temperate birds. At the cellular level, primary dermal fibroblasts from tropical birds tend to have lower cellular metabolic rates and appear to be more resistant to oxidative cell stress than those of temperate birds. However, at the subcellular level, lipid peroxidation rates, a measure of the ability of lipid molecules within the cell membranes to thwart the propagation of oxidative damage, appear not to be different between tropical and temperate species. Nevertheless, lipids in mitochondrial membranes of tropical birds tend to have increased concentrations of plasmalogens (phospholipids with antioxidant properties), and decreased concentrations of cardiolipin (a complex phospholipid in the electron transport chain) compared with temperate birds.

Micro-mechanical model for the tension-stabilized enzymatic degradation of collagen tissues

Science.gov (United States)

Nguyen, Thao; Ruberti, Jeffery

We present a study of how the collagen fiber structure influences the enzymatic degradation of collagen tissues. Experiments of collagen fibrils and tissues show that mechanical tension can slow and halt enzymatic degradation. Tissue-level experiments also show that degradation rate is minimum at a stretch level coincident with the onset of strain-stiffening in the stress response. To understand these phenomena, we developed a micro-mechanical model of a fibrous collagen tissue undergoing enzymatic degradation. Collagen fibers are described as sinusoidal elastica beams, and the tissue is described as a distribution of fibers. We assumed that the degradation reaction is inhibited by the axial strain energy of the crimped collagen fibers. The degradation rate law was calibrated to experiments on isolated single fibrils from bovine sclera. The fiber crimp and properties were fit to uniaxial tension tests of tissue strips. The fibril-level kinetic and tissue-level structural parameters were used to predict tissue-level degradation-induced creep rate under a constant applied force. We showed that we could accurately predict the degradation-induce creep rate of the pericardium and cornea once we accounted for differences in the fiber crimp structure and properties.

Characterization of the novel dimethyl sulfide-degrading bacterium Alcaligenes sp. SY1 and its biochemical degradation pathway

Energy Technology Data Exchange (ETDEWEB)

Sun, Yiming; Qiu, Jiguo; Chen, Dongzhi; Ye, Jiexu; Chen, Jianmeng, E-mail: jchen@zjut.edu.cn

2016-03-05

Highlights: • A novel efficient DMS-degrading bacterium Alcaligenes sp. SY1 was identified. • A RSM was applied to optimize incubation condition of Alcaligenes sp. SY1. • SIP was applied as C{sup 13} labelled DMS to trace intermediates during DMS degradation. • Kinetics of DMS degradation via batch experiment was revealed. • Carbon and sulfur balance were analyzed during DMS degradation process. - Abstract: Recently, the biodegradation of volatile organic sulfur compounds (VOSCs) has become a burgeoning field, with a growing focus on the reduction of VOSCs. The reduction of VOSCs encompasses both organic emission control and odor control. Herein, Alcaligenes sp. SY1 was isolated from active sludge and found to utilize dimethyl sulfide (DMS) as a growth substrate in a mineral salt medium. Response surface methodology (RSM) analysis was applied to optimize the incubation conditions. The following conditions for optimal degradation were identified: temperature 27.03 °C; pH 7.80; inoculum salinity 0.84%; and initial DMS concentration 1585.39 μM. Under these conditions, approximately 99% of the DMS was degraded within 30 h of incubation. Two metabolic compounds were detected and identified by gas chromatography–mass spectrometry (GC–MS): dimethyl disulfide (DMDS) and dimethyl trisulfide (DMTS). The DMS degradation kinetics for different concentrations were evaluated using the Haldane–Andrews model and the pseudo first-order model. The maximum specific growth rate and degradation rate of Alcaligenes sp. SY1 were 0.17 h{sup −1} and 0.63 gs gx{sup −1} h{sup −1}. A possible degradation pathway is proposed, and the results suggest that Alcaligenes sp. SY1 has the potential to control odor emissions under aerobic conditions.

Gas generation from transuranic waste degradation: an interim assessment

International Nuclear Information System (INIS)

Molecke, M.A.

1979-10-01

A review of all available, applicable data pertaining to gas generation from the degradation of transuranic waste matrix material and packaging is presented. Waste forms are representative of existing defense-related TRU wastes and include cellulosics, plastics, rubbers, concrete, process sludges, and mild steel. Degradation mechanisms studied were radiolysis, thermal, bacterial, and chemical corrosion. Gas generation rates are presented in terms of moles of gas produced per year per drum, and in G(gas) values for radiolytic degradation. Comparison of generation rates is made, as is a discussion of potential short- and long-term concerns. Techniques for reducing gas generation rates are discussed. 6 figures, 10 tables

Evidence for age-related performance degradation of (241)Am foil sources commonly used in UK schools.

Science.gov (United States)

Whitcher, R; Page, R D; Cole, P R

2014-06-01

The characteristics of alpha radiation have for decades been demonstrated in UK schools using small sealed (241)Am sources. There is a small but steady number of schools who report a considerable reduction in the alpha count rate detected by an end-window GM detector compared with when the source was new. This cannot be explained by incorrect apparatus or set-up, foil surface contamination, or degradation of the GM detector. The University of Liverpool and CLEAPSS collaborated to research the cause of this performance degradation. The aim was to find what was causing the performance degradation and the ramifications for both the useful and safe service life of the sources. The research shows that these foil sources have greater energy straggling with a corresponding reduction in spectral peak energy. A likely cause for this increase in straggling is a significant diffusion of the metals over time. There was no evidence to suggest the foils have become unsafe, but precautionary checks should be made on old sources.

Polymer scaffold degradation control via chemical control

Science.gov (United States)

Hedberg-Dirk, Elizabeth L.; Dirk, Shawn; Cicotte, Kirsten

2016-01-05

A variety of polymers and copolymers suitable for use as biologically compatible constructs and, as a non-limiting specific example, in the formation of degradable tissue scaffolds as well methods for synthesizing these polymers and copolymers are described. The polymers and copolymers have degradation rates that are substantially faster than those of previously described polymers suitable for the same uses. Copolymers having a synthesis route which enables one to fine tune the degradation rate by selecting the specific stoichiometry of the monomers in the resulting copolymer are also described. The disclosure also provides a novel synthesis route for maleoyl chloride which yields monomers suitable for use in the copolymer synthesis methods described herein.

Determination of the light-induced degradation rate of the solar cell sensitizer N719 on TiO2 nanocrystalline particles

DEFF Research Database (Denmark)

Nour-Mohammadi, Farahnaz; Doan Nguyen, Sau; Boschloo, Gerrit

2005-01-01

The oxidative degradation rate, kdeg of the solar cell dye (Bu4N+)2 [Ru(dcbpyH)2(NCS)2]2–, referred to as N719 or [RuL2(NCS)2], was obtained by applying a simple model system. Colloidal solutions of N719-dyed TiO2 particles in acetonitrile were irradiated with 532-nm monochromatic light, and the ...

Plasma-Based Degradation of Mycotoxins Produced by Fusarium, Aspergillus and Alternaria Species

Directory of Open Access Journals (Sweden)

Lars ten Bosch

2017-03-01

Full Text Available The efficacy of cold atmospheric pressure plasma (CAPP with ambient air as working gas for the degradation of selected mycotoxins was studied. Deoxynivalenol, zearalenone, enniatins, fumonisin B1, and T2 toxin produced by Fusarium spp., sterigmatocystin produced by Aspergillus spp. and AAL toxin produced by Alternaria alternata were used. The kinetics of the decay of mycotoxins exposed to plasma discharge was monitored. All pure mycotoxins exposed to CAPP were degraded almost completely within 60 s. Degradation rates varied with mycotoxin structure: fumonisin B1 and structurally related AAL toxin were degraded most rapidly while sterigmatocystin exhibited the highest resistance to degradation. As compared to pure compounds, the degradation rates of mycotoxins embedded in extracts of fungal cultures on rice were reduced to a varying extent. Our results show that CAPP efficiently degrades pure mycotoxins, the degradation rates vary with mycotoxin structure, and the presence of matrix slows down yet does not prevent the degradation. CAPP appears promising for the decontamination of food commodities with mycotoxins confined to or enriched on surfaces such as cereal grains.

Associations between deprived life circumstances, wellbeing and self-rated health in a socially marginalized population.

Science.gov (United States)

Pedersen, Pia V; Grønbæk, Morten; Curtis, Tine

2012-10-01

Previous studies of self-rated health among socially marginalized people provide insufficient understandings of what influences their self-rated health. This study aimed to examine how disadvantaged life circumstances (homelessness, substance abuse, poverty) and general well-being were associated with poor self-rated health among the socially marginalized. In a nationwide survey in Denmark, 1348 users of shelters, drop-in centres, treatment centres and social psychiatric centres answered a self-administered questionnaire. We analysed data using logistic regression. Disadvantaged life circumstances and well-being were associated with self-rated health, also when controlling for illness, mental disorder and age. Male respondents exposed to two or more disadvantaged life circumstances had higher odds of poor self-rated health [odds ratio (OR): 2.96; 95% confidence interval (CI): 1.80-4.87] than males exposed to fewer disadvantages. A low sense of personal well-being implied higher odds of poor self-rated health among both men and women. Among men, not showering regularly (OR: 1.81; 95% CI: 1.17-2.79), and among women, not eating varied food (OR: 2.24; 95% CI: 1.20-4.20) and exposure to physical violence (borderline significant) implied higher odds of poor self-rated health. Male and female respondents reporting lack of sleep and loneliness (borderline significant among women) had higher odds of poor self-rated health. The poor self-rated health among socially marginalized is strongly associated with massive social problems, poor living conditions and poor well-being. This study elucidates the need for more broadly based and holistic initiatives by both the health sector and the social services, incorporating health promotion initiatives into social work.

Accuracy and Reliability in the Prediction of End-of-Life Performance of Solar Generators

Science.gov (United States)

Rapp, Etienne

2008-09-01

The end-of-life power analysis of solar arrays is calculated using a combination of arithmetic and root square sums of loss factors. These loss factors are sometimes linked to degradations, sometimes linked to uncertainties. The uncertainties of the degradations are taken into account considering contractual "worst cases". This paper will put the first stones for a move "metrological" evaluation of the probable performance associated with a standard uncertainty. The turn from silicon to triple junction solar cells induces some changes in the degradation parameters of solar arrays: * The triple junction cells are more sensitive to UV darkening than silicon ones. * The cell voltage is higher and the current is lower. Then the cell strings are shorter, and there are more strings in parallel. This induces some changes in the reliability analyses and risk management. * The failure modes and failure rates of these cells have to be compared and discussed. We try to define improved rules to design solar arrays for end of life performance, for a better knowledge of the margins and a better reliability.

Life span and tumorigenesis in mice exposed to continuous low dose-rate gamma-rays

International Nuclear Information System (INIS)

Tanaka, Satoshi; Braga-Tanaka III, Ignacia; Takabatake, Takashi; Ichinohe, Kazuaki; Tanaka, Kimio; Matsumoto, Tsuneya; Sato, Fumiaki

2004-01-01

Two experiments were conducted to evaluate late biological effects of chronic low dose-rate radiation. 1: Late effects of chronic low dose-rate gamma-ray irradiation on SPF mice, using life span and pathological changes as parameters. Continuous irradiation for approximately 400 days was performed using 137 Cs gamma-rays at dose-rates of 20 mGy/day, 1 mGy/day and 0.05 mGy/day with accumulated doses equivalent to 8000 mGy, 400 mGy and 20 mGy, respectively. All mice were kept until their natural death. Statistical analyses show that the life spans of the both sexes irradiated at 20 mGy/day (p<0.0001) and of females irradiated at 1 mGy/day (p<0.05) were significantly shorter than those of the control group. There was no evidence of lengthened life span in mice continuously exposed to very low dose-rates of gama-rays. Pathodological examinations showed that the most frequently observed lethal neoplasms in males were malignant lymphomas, liver, lung, and soft tissue neoplasms, whereas, in females, malignant lymphomas and soft tissue neoplasms were common. No significant difference in the causes of death and mortality rates between groups. Hematopoietic neoplasms (malignant lymphoma and myeloid leukemia), liver, lung and soft tissue neoplasms, showed a tendency to appear at a younger age in both sexes irradiated at 20 mGy/day. Experiment 2: effects on the progeny of chronic low dose-rate gamma-ray irradiated SPF mice: preliminary study. No significant difference was observed between non-irradiated group and irradiated group with regards to litter size, sex ratio and causes of death in F1 and F2 mice. (author)

Cellular Metabolic Rate Is Influenced by Life-History Traits in Tropical and Temperate Birds

Science.gov (United States)

Jimenez, Ana Gabriela; Van Brocklyn, James; Wortman, Matthew; Williams, Joseph B.

2014-01-01

In general, tropical birds have a “slow pace of life,” lower rates of whole-animal metabolism and higher survival rates, than temperate species. A fundamental challenge facing physiological ecologists is the understanding of how variation in life-history at the whole-organism level might be linked to cellular function. Because tropical birds have lower rates of whole-animal metabolism, we hypothesized that cells from tropical species would also have lower rates of cellular metabolism than cells from temperate species of similar body size and common phylogenetic history. We cultured primary dermal fibroblasts from 17 tropical and 17 temperate phylogenetically-paired species of birds in a common nutritive and thermal environment and then examined basal, uncoupled, and non-mitochondrial cellular O2 consumption (OCR), proton leak, and anaerobic glycolysis (extracellular acidification rates [ECAR]), using an XF24 Seahorse Analyzer. We found that multiple measures of metabolism in cells from tropical birds were significantly lower than their temperate counterparts. Basal and uncoupled cellular metabolism were 29% and 35% lower in cells from tropical birds, respectively, a decrease closely aligned with differences in whole-animal metabolism between tropical and temperate birds. Proton leak was significantly lower in cells from tropical birds compared with cells from temperate birds. Our results offer compelling evidence that whole-animal metabolism is linked to cellular respiration as a function of an animal’s life-history evolution. These findings are consistent with the idea that natural selection has uniquely fashioned cells of long-lived tropical bird species to have lower rates of metabolism than cells from shorter-lived temperate species. PMID:24498080

Degradation of diclofenac by UV-activated persulfate process: Kinetic studies, degradation pathways and toxicity assessments.

Science.gov (United States)

Lu, Xian; Shao, Yisheng; Gao, Naiyun; Chen, Juxiang; Zhang, Yansen; Xiang, Huiming; Guo, Youluo

2017-07-01

Diclofenac (DCF) is the frequently detected non-steroidal pharmaceuticals in the aquatic environment. In this study, the degradation of DCF was evaluated by UV-254nm activated persulfate (UV/PS). The degradation of DCF followed the pseudo first-order kinetics pattern. The degradation rate constant (k obs ) was accelerated by UV/PS compared to UV alone and PS alone. Increasing the initial PS dosage or solution pH significantly enhanced the degradation efficiency. Presence of various natural water constituents had different effects on DCF degradation, with an enhancement or inhibition in the presence of inorganic anions (HCO 3 - or Cl - ) and a significant inhibition in the presence of NOM. In addition, preliminary degradation mechanisms and major products were elucidated using LC-MS/MS. Hydroxylation, decarbonylation, ring-opening and cyclation reaction involving the attack of SO 4 • - or other substances, were the main degradation mechanism. TOC analyzer and Microtox bioassay were employed to evaluate the mineralization and cytotoxicity of solutions treated by UV/PS at different times, respectively. Limited elimination of TOC (32%) was observed during the mineralization of DCF. More toxic degradation products and their related intermediate species were formed, and the UV/PS process was suitable for removing the toxicity. Of note, longer degradation time may be considered for the final toxicity removal. Copyright © 2017. Published by Elsevier Inc.

Degradation of paracetamol in aqueous solutions by TiO2 photocatalysis.

Science.gov (United States)

Yang, Liming; Yu, Liya E; Ray, Madhumita B

2008-07-01

In this study, photo/photocatalytic oxidation of common analgesic and antipyretic drug, paracetamol (acetaminophen), was investigated to determine the optimal operating conditions for degradation in water. UVA (365 nm) radiation alone degraded negligible amount of paracetamol, whereas paracetamol concentration decreased substantially under an irradiation of UVC (254 nm) with marginal changes in total organic carbon (TOC). In the presence of TiO2, much faster photodegradation of paracetamol and effective mineralization occurred; more than 95% of 2.0mM paracetamol was degraded within 80 min. The degradation rate constant decreased with an increase in the initial concentration of paracetamol, while it increased with light intensity and oxygen concentration. The degradation rate also increased with TiO2 loading until a concentration of 0.8 g L(-1). The degradation rate slowly increased between pH 3.5 and 9.5, but significantly decreased with increasing pH between 9.5 and 11.0. Based on the experimental data, a kinetic equation describing paracetamol photocatalytic degradation with various process parameters is obtained.

determination of the specific growth rate on degradation of cassava

African Journals Online (AJOL)

user

aerobic technique was used to effect the degradation in a batch reactor. Sodium ... The substrate concentration is higher at 10 g and low at 0 g and 2 g. At higher ... grown in many countries, such as tropical Africa, Asia and ... efforts are with varied levels of success, cost ... which air mixture of oxygen with other gases freely.

Canadian programs on understanding and managing aging degradation of nuclear power plant components

International Nuclear Information System (INIS)

Chadha, J.A.; Pachner, J.

1989-06-01

Maintaining adequate safety and reliability of nuclear power plants and nuclear power plant life assurance and life extension are growing in importance as nuclear plants get older. Age-related degradation of plant components is complex and not fully understood. This paper provides an overview of the Canadian approach and the main activities and their results towards understanding and managing age-related degradation of nuclear power plant components, structures and systems. A number of pro-active programs have been initiated to anticipate, detect and mitigate potential aging degradation at an early stage before any serious impact on plant safety and reliability. These programs include Operational Safety Management Program, Nuclear Plant Life Assurance Program, systematic plant condition assessment, refurbishment and upgrading, post-service examination and testing, equipment qualification, research and development, and participation in the IAEA programs on safety aspects of nuclear power plant aging and life extension. A regulatory policy on nuclear power plants is under development and will be based on the domestic as well as foreign and international studies and experience

Gas-liquid hybrid discharge-induced degradation of diuron in aqueous solution.

Science.gov (United States)

Feng, Jingwei; Zheng, Zheng; Luan, Jingfei; Li, Kunquan; Wang, Lianhong; Feng, Jianfang

2009-05-30

Degradation of diuron in aqueous solution by gas-liquid hybrid discharge was investigated for the first time. The effect of output power intensity, pH value, Fe(2+) concentration, Cu(2+) concentration, initial conductivity and air flow rate on the degradation efficiency of diuron was examined. The results showed that the degradation efficiency of diuron increased with increasing output power intensity and increased with decreasing pH values. In the presence of Fe(2+), the degradation efficiency of diuron increased with increasing Fe(2+) concentration. The degradation efficiency of diuron was decreased during the first 4 min and increased during the last 10 min with adding of Cu(2+). Decreasing the initial conductivity and increasing the air flow rate were favorable for the degradation of diuron. Degradation of diuron by gas-liquid hybrid discharge fitted first-order kinetics. The pH value of the solution decreased during the reaction process. Total organic carbon removal rate increased in the presence of Fe(2+) or Cu(2+). The generated Cl(-1), NH(4)(+), NO(3)(-), oxalic acid, acetic acid and formic acid during the degradation process were also detected. Based on the detected Cl(-1) and other intermediates, a possible degradation pathway of diuron was proposed.

Degradation of polyethylene induced by plasma in oxidizing atmospheres

International Nuclear Information System (INIS)

Colin, E.; Olayo, M.G.; Cruz, G.J.

2002-01-01

The garbage of polyethylene is not easily degradable in normal environmental conditions . The indiscriminate use of this polymer and the enormous quantity of garbage which is generated carries a damage to the environment due to its long life as waste. The objective of this work is to study the conditions in which can be carried out the degradation of polyethylene. A form of accelerating the degradation is exposing it to plasma with reactive atmospheres. In this work a study of surface modification of polyethylene by plasmas with discharges of direct current of oxygen and nitrogen is presented. (Author)

Microbial degradation of dissolved proteins in seawater

International Nuclear Information System (INIS)

Hollibaugh, J.T.; Azam, F.

1983-01-01

An experimental protocol using radiolabeled proteins was developed to investigate the rates and mechanisms whereby dissolved proteins are degraded in natural marine plankton communities. The results of field observations and laboratory experiments indicate that proteins are degraded by a particle-bound, thermolabile system, presumably bacteria-associated enzymes, with an apparent half-saturation constant of ca. 25 μg bovine serum albumin (BSA) per liter. Gel permeation chromatography indicated that peptides of chain length intermediate between BSA and the final products of degradation (MW<700) do not accumulate in the medium. Competition experiments indicate that the system is relatively nonspecific. Turnover rates for the protein pool in samples collected in the Southern California Bight were of the same order of magnitude as the turnover rate of the L-leucine pool and were correlated with primary productivity, chlorophyll a concentrations, bacterial abundance and biomass, and L-leucine turnover rate. These data suggest that amino acids derived from proteins are utilized preferentially and do not completely mix with the amino acids in the bulk phase

Hydrocarbon degradation potential in reference soils and soils contaminated with jet fuel

International Nuclear Information System (INIS)

Lee, R.F.; Hoeppel, R.

1991-01-01

Petroleum degradation in surface and subsurface soils is affected by such factors as moisture content, pH, soil type, soil organics, temperature, and oxygen concentrations. In this paper, the authors determine the degradation rates of 14 C-labeled hydrocarbons added to soils collected from a contaminated surface site, contaminated subsurface sites, and a clean reference site. The radiolabeled hydrocarbons used include benzene, toluene, naphthalene, 1-methynaphthalene, phenanthrene, fluorene, anthracene, chrysene, and hexadecane. Microbial degradation rates were based on determination of mineralization rates (production of 14 CO 2 ) of hydrocarbons that were added to soil samples. Since water was added and oxygen was not limiting, the hydrocarbon rates determined are likely to be higher than those occurring in situ. Using radiolabeled hydrocarbons, information can be provided on differences in the degradation rates of various petroleum compounds in different types of soils at a site, on possible production of petroleum metabolites in the soil, and on the importance of anaerobic petroleum degradation and the effects of nutrient, water, and surfactant addition on biodegradation rates

Microbial degradation of pharmaceuticals in estuarine and coastal seawater

Energy Technology Data Exchange (ETDEWEB)

Benotti, Mark J. [Marine Sciences Research Center, Stony Brook University, Stony Brook, NY 11794-5000 (United States); Brownawell, Bruce J. [Marine Sciences Research Center, Stony Brook University, Stony Brook, NY 11794-5000 (United States)], E-mail: bruce.brownawell@sunysb.edu

2009-03-15

Microbial degradation rates were measured for 19 pharmaceuticals in estuarine and coastal surface water samples. Antipyrine, carbamazepine, cotinine, sulfamethoxazole, and trimethoprim were the most refractory (half-lives, t{sub 1/2} = 35 to >100 days), making them excellent candidates for wastewater tracers. Nicotine, acetaminophen, and fluoxetine were labile across all treatments (t{sub 1/2} = 0.68-11 days). Caffeine, diltiazem, and nifedipine were also and relatively labile in all but one of the treatments (t{sub 1/2} = 3.5-13 days). Microbial degradation of caffeine was further confirmed by production {sup 14}CO{sub 2}. The fastest decay of non-refractory compounds was always observed in more sewage-affected Jamaica Bay waters. Degradation rates for the majority of these pharmaceuticals are much slower than reported rates for small biomolecules, such as glucose and amino acids. Batch sorption experiments indicate that removal of these soluble pharmaceuticals from the water column to sediments is a relatively insignificant removal process in these receiving waters. - Microbial degradation rates were measured for 19 structurally variable pharmaceuticals in wastewater-impacted estuarine and coastal seawater.

Microbial degradation of pharmaceuticals in estuarine and coastal seawater

International Nuclear Information System (INIS)

Benotti, Mark J.; Brownawell, Bruce J.

2009-01-01

Microbial degradation rates were measured for 19 pharmaceuticals in estuarine and coastal surface water samples. Antipyrine, carbamazepine, cotinine, sulfamethoxazole, and trimethoprim were the most refractory (half-lives, t 1/2 = 35 to >100 days), making them excellent candidates for wastewater tracers. Nicotine, acetaminophen, and fluoxetine were labile across all treatments (t 1/2 = 0.68-11 days). Caffeine, diltiazem, and nifedipine were also and relatively labile in all but one of the treatments (t 1/2 = 3.5-13 days). Microbial degradation of caffeine was further confirmed by production 14 CO 2 . The fastest decay of non-refractory compounds was always observed in more sewage-affected Jamaica Bay waters. Degradation rates for the majority of these pharmaceuticals are much slower than reported rates for small biomolecules, such as glucose and amino acids. Batch sorption experiments indicate that removal of these soluble pharmaceuticals from the water column to sediments is a relatively insignificant removal process in these receiving waters. - Microbial degradation rates were measured for 19 structurally variable pharmaceuticals in wastewater-impacted estuarine and coastal seawater

[Water utilization characteristics of the degraded poplar shelterbelts in Zhangbei, Hebei, China.

Science.gov (United States)

Zhang, Huan; Cao, Jun; Wang, Hua Bing; Song, Bo; Jia, Guo Dong; Liu, Zi Qiang; Yu, Xin Xiao; Zeng, Jia

2018-05-01

In Zhangbei County, Hebei Province, poplar-dominated shelterbelts are degraded to different extents. Water availability is the main limiting factor for plant survival in arid areas. The purpose of this study was to reveal the relationship between water availability and poplar degradation. Based on the hydrogen and oxygen stable isotope techniques, we explored the water sources of Populus simonii under different degradation degrees by comparing the isotopic values of P. simonii xylem water with that in potential water source, and calculated the utilization ratio of each water source. The results showed that the water sources of poplar trees varied with degradation degree. The water sources of P. simonii gradually transferred from the deep layer to the surface layer with the increases of degradation. P. simonii with no degradation mainly absorbed soil water in the range of 320-400 cm, with the utilization rate being 25.1%. P. simonii with slight degradation mainly used soil water at depth of 120-180, 180-240 and 240-320 cm. The total utilization rate of three layers was close to 50.0%, with less utilization of water from other layers. The moderately degraded P. simonii mainly used soil water at depth of 20-40, 40-60 and 60-80 cm. The utilization rate of each layer was 17.5%-20.9%, and the contribution rate of soil water under 120 cm was less than 10.0%. The severely degraded P. simonii mainly used water from surface soil layer (0-20 cm), with the utilization rate being 30.4%, which was significantly higher than that of other water sources. The water sources of poplar shelter forests were gradually shallower during the process of degradation. However, the low soil water content in the shallow layer could not meet the normal water demand of poplar, which would accelerate the degradation and even decline of poplar.

Photocatalytic degradation of paraoxon-ethyl in aqueous solution using titania nanoparticulate film

International Nuclear Information System (INIS)

Prasad, G.K.; Ramacharyulu, P.V.R.K.; Kumar, J. Praveen; Srivastava, A.R.; Singh, Beer

2012-01-01

Photocatalytic degradation of paraoxon-ethyl (o,o-diethyl o-(4-nitrophenyl) phosphate), a well known surrogate of chemical warfare agents, in aqueous solution was studied by using titania nanoparticulate film. Reaction followed pseudo first order behaviour. Photolytic degradation reaction of paraoxon-ethyl demonstrated relatively low rate with a value of rate constant of 2.5 × 10 −3 min −1 . Whereas, degradation reaction in the presence of titania nanoparticulate film and UV light displayed enhanced rate with a value of rate constant of 6.9 × 10 −3 min −1 due to photocatalysis. Gas chromatography–mass spectrometry analysis showed the formation of p-nitrophenol, o,o-diethyl phosphonic acid, o-ethyl, diphosphonic acid, phosphoric acid, dimerized product of o,o-diethyl phosphonic acid, acetaldehyde, and carbon dioxide due to photocatalytic degradation of paraoxon-ethyl. It indicates that, photocatalytic degradation reaction begins with destruction of P–O–C bonds. Subsequently, P, C atoms were found to be oxidized gradually, and contributed to its photocatalytic degradation. - Highlights: ► Synthesis of titania nanoparticles by sol–gel method. ► Fabrication of titania nanoparticulate film by dip coating. ► Paraoxon ethyl degradation reactions followed pseudo first order behaviour. ► Paraoxon-ethyl degraded to non toxic compounds like CO 2 , acetaldehyde, and nitrophenol.

Improvement of life prediction accuracy by introduction of strain-rate effect into modified ductility exhaustion method

International Nuclear Information System (INIS)

Takahashi, Yukio

1994-01-01

It is important to use a reliable creep-fatigue damage evaluation method to prevent failures due to creep-fatigue damage accumulated during operation life in the structural design for fast breeder reactor plants. In this study, slow strain-rate fatigue tests were conducted for SUS316 steel for fast breeder application (316FR) and the improvement of creep-fatigue life estimation method was proposed based on test results. Main results can be summarized as follows: (1) In the slow strain-rate fatigue tests, life reduction caused by creep damage was observed as in the case of strain-hold creep-fatigue tests. (2) Strain-rate dependency of creep damage was introduced into the modified ductility exhaustion method previously proposed by the author. Good agreement of predicted lives with observed lives was achieved for SUS304 and 316FR steels with the method proposed here. (author)

Halide salts accelerate degradation of high explosives by zerovalent iron

International Nuclear Information System (INIS)

Kim, Jong Sung; Shea, Patrick J.; Yang, Jae E.; Kim, Jang-Eok

2007-01-01

Zerovalent iron (Fe 0 , ZVI) has drawn great interest as an inexpensive and effective material to promote the degradation of environmental contaminants. A focus of ZVI research is to increase degradation kinetics and overcome passivation for long-term remediation. Halide ions promote corrosion, which can increase and sustain ZVI reactivity. Adding chloride or bromide salts with Fe 0 (1% w/v) greatly enhanced TNT, RDX, and HMX degradation rates in aqueous solution. Adding Cl or Br salts after 24 h also restored ZVI reactivity, resulting in complete degradation within 8 h. These observations may be attributed to removal of the passivating oxide layer and pitting corrosion of the iron. While the relative increase in degradation rate by Cl - and Br - was similar, TNT degraded faster than RDX and HMX. HMX was most difficult to remove using ZVI alone but ZVI remained effective after five HMX reseeding cycles when Br - was present in solution. - The addition of halide ions promotes the degradation of high explosives by zerovalent iron

Possibility of electron beam irradiation degradation of many pesticides in ginseng oral liquid

International Nuclear Information System (INIS)

Chen Qiyong; Liu Yang; Ge Hanguang; Wu Ruoxin

2013-01-01

This paper is to explore the technological feasibility in degradation of pesticides in ginseng oral liquid under the irradiation of electron beam. Sixteen residual concentration-restricted pesticides in ginseng oral liquid were experimented under the dose of 0 ∼ 15 kGy. Results showed that, when the dose of the irradiation of electron beam increased, the degradation rates of all the pesticides enhanced, and the electron beam radiation showed the most remarkable effect on the degradation of pesticides such as imidacloprid and fenpropathrinwith degradation rates of more than 90% and 50%, respectively. The degradation rates of fonofos, methidathion, diazinon, phosalone and carbaryl were all higher than 30%. No significant degradation was observed in the other 9 pesticides under the same condition. (authors)

Management of age-related degradation for nuclear power plants

International Nuclear Information System (INIS)

Gregor, Frank E.

2004-01-01

Life extension for nuclear power plants has been studied in the USA for the last six years, largely supported by EPRI, DOE and the USNRC. Though there are diverse opinions for the strategies and priorities of life extension and aging management, one common conclusion has been formulated regarding the need of current maintenance programs having to focus on aging and degradation management. Such program, called 'Maintenance Effectiveness Evaluation and Enhancement' or M3E for short, has been developed to assist plant operators to upgrade and enhance existing programs by integrating aging/degradation management activities for important or critical equipment and components. The key elements of the M3E program consist of the definition and selection of the critical components or commodities to be included in the scope, the survey/inventory of the current programs and their respective action steps, frequencies, corrective measures and extent of coverage, the component/commodity degradation mechanism, sites and severity, safety functions and service environments and lastly, the correlation of degradation/aging with the individual maintenance activities. The degree of correlation provides a measure of effectiveness and the opportunity to identify/specify needed enhancements, abandonment or generation of new maintenance activities. Implementation of the activities can then be prioritized at the option of the plant staff. (author)

Host factor I, Hfq, binds to Escherichia coli ompA mRNA in a growth rate-dependent fashion and regulates its stability

DEFF Research Database (Denmark)

Vytvytska, O; Jakobsen, J S; Balcunaite, G

1998-01-01

RNA. In hfq mutant cells with a deficient Hfq gene product, the RNA-binding activity is missing, and analysis of the ompA mRNA showed that the growth-rate dependence of degradation is lost. Furthermore, the half-life of the ompA mRNA is prolonged in the mutant cells, irrespective of growth rate. Hfq has...

Remaining life diagnosis method and device for nuclear reactor

International Nuclear Information System (INIS)

Yamamoto, Michiyoshi.

1996-01-01

A neutron flux measuring means is inserted from the outside of a reactor pressure vessel during reactor operation to forecast neutron-degradation of materials of incore structural components in the vicinity of portions to be measured based on the measured values, and the remaining life of the reactor is diagnosed by the forecast degraded state. In this case, the neutron fluxes to be measured are desirably fast and/or medium neutron fluxes. As the positions where the measuring means is to be inserted, for example, the vicinity of the structural components at the periphery of the fuel assembly is selected. Aging degradation characteristics of the structural components are determined by using the aging degradation data for the structural materials. The remaining life is analyzed based on obtained aging degradation characteristics and stress evaluation data of the incore structural components at portions to be measured. Neutron irradiation amount of structural components at predetermined positions can be recognized accurately, and appropriate countermeasures can be taken depending on the forecast remaining life thereby enabling to improve the reliability of the reactor. (N.H.)

Reliability Analysis of Load-Sharing K-out-of-N System Considering Component Degradation

Directory of Open Access Journals (Sweden)

Chunbo Yang

2015-01-01

Full Text Available The K-out-of-N configuration is a typical form of redundancy techniques to improve system reliability, where at least K-out-of-N components must work for successful operation of system. When the components are degraded, more components are needed to meet the system requirement, which means that the value of K has to increase. The current reliability analysis methods overestimate the reliability, because using constant K ignores the degradation effect. In a load-sharing system with degrading components, the workload shared on each surviving component will increase after a random component failure, resulting in higher failure rate and increased performance degradation rate. This paper proposes a method combining a tampered failure rate model with a performance degradation model to analyze the reliability of load-sharing K-out-of-N system with degrading components. The proposed method considers the value of K as a variable which is derived by the performance degradation model. Also, the load-sharing effect is evaluated by the tampered failure rate model. Monte-Carlo simulation procedure is used to estimate the discrete probability distribution of K. The case of a solar panel is studied in this paper, and the result shows that the reliability considering component degradation is less than that ignoring component degradation.

Methane oxidation and degradation of organic compounds in landfill soil covers

DEFF Research Database (Denmark)

Scheutz, Charlotte; Kjeldsen, Peter

2002-01-01

High rates of methane oxidation and degradation of the lowed halogenated methanes (TCM and DCM) and HCFCs (HCFC-21 and HCFC-22) were found in an investigation of the oxidation of methane and halogenated organic compunds (HOCs) in landfill gas affected soil. The degradation followed zero-order kin......High rates of methane oxidation and degradation of the lowed halogenated methanes (TCM and DCM) and HCFCs (HCFC-21 and HCFC-22) were found in an investigation of the oxidation of methane and halogenated organic compunds (HOCs) in landfill gas affected soil. The degradation followed zero...

Degradation failure model of self-healing metallized film pulse capacitor

International Nuclear Information System (INIS)

Sun Quan; Zhong Zheng; Zhou Jinglun; Zhao Jianyin; Wei Xiaofeng; Guo Liangfu; Zhou Pizhang; Li Yizheng; Chen Dehuai

2004-01-01

The high energy density self-healing metallized film pulse capacitor has been applied to all kinds of laser facilities for their power conditioning systems, whose reliability and expense are straightforwardly affected by the reliability level of the capacitors. Based on the related research in literature, this paper analyses the degradation mechanism of the capacitor, and presents a new degradation failure model--the Gauss-Poisson model. The Gauss-Poisson model divides degradation of capacitor into naturalness degradation and outburst one. Compared with traditional Weibull failure model, the new model is more precise in evaluating the lifetime of the capacitor, and the life tests for this model are simple in design, and lower in the cost of time or expense. The Gauss-Poisson model will be a fine and widely used degradation disable model. (author)

Degradation and adsorption of tralkoxydim in Chinese soils and water-sediment environments.

Science.gov (United States)

Wu, Wen Zhu; Shan, Zheng Jun; Kong, De Yang; He, Jian

2017-06-01

Tralkoxydim is a cyclohexanedione herbicide primarily used for gramineous weed control in China. In this paper, we present results of a tralkoxydim laboratory environmental fate study characterizing its degradation, adsorption, and mobility behavior in three different soils and two water-sediment systems (river and lake) in China. Degradation half-life of tralkoxydim in soil under aerobic conditions was 5.1, 7.7, and 7.9 days in Jiangxi red soil, Taihu paddy soil, and Northeast China black soil, respectively. Under anaerobic and flooding conditions, half-life values were 6.2, 15.1, and 19.8 days for the same three soils, respectively. Soil pH was the major factor effecting tralkoxydim degradation. In the aerobic water-sediment experiments, tralkoxydim degraded faster in the river system (total system half-life 43.3 days) than the lake system (total system half-life 99.0 days). Correspondingly, its anaerobic degradation half-life values were 46.2 and 53.3 days for the river and lake systems, respectively. Tralkoxydim adsorption in the three soils was found to follow the empirical Freundlich isotherm. The adsorption coefficient (K d ) was 8.60, 1.00, and 1.57 for Jiangxi red soil, Taihu paddy soil, and Northeast China black soil, respectively. Soil pH was the major factor effecting tralkoxydim adsorption. Adsorption free energy change was less than 40 kJ mol -1 in all three soils, indicating a physical mechanism in the process. Thin-layer chromatography (TLC) tests showed that relative to the solvent transport to 11.5 cm, the travel distance of tralkoxydim was 8-10 cm in the three soils, corresponding Rf values at 0.05, 0.35, and 0.75 for Jiangxi red soil, Taihu paddy soil, and Northeast China black soil, respectively. Results of this work suggest that under alkaline conditions, tralkoxydim adsorption becomes smaller; thus, assessments on its mobility and potential groundwater impact should focus on these soil types.

Effect of solvents on the enzyme mediated degradation of copolymers

International Nuclear Information System (INIS)

Banerjee, Aditi; Chatterjee, Kaushik; Madras, Giridhar

2015-01-01

The biodegradation of polycaprolactone (PCL), polylactic acid (PLA), polyglycolide (PGA) and their copolymers, poly (lactide-co-glycolide) and poly (D, L-lactide-co-caprolactone) (PLCL) was investigated. The influence of different solvents on the degradation of these polymers at 37 °C in the presence of two different lipases namely Novozym 435 and the free lipase of porcine pancreas was investigated. The rate coefficients for the polymer degradation and enzyme deactivation were determined using continuous distribution kinetics. Among the homopolymers, the degradation of PGA was nearly an order of magnitude lower than that for PCL and PLA. The overall rate coefficients of the copolymers were higher than their respective homopolymers. Thus, PLCL degraded faster than either PCL or PLA. The degradation was highly dependent on the viscosity of the solvent used with the highest degradation observed in acetone. The degradation of the polymers in acetone was nearly twice that observed in dimethyl sulfoxide indicating that the degradation decreases with increase in the solvent viscosity. The degradation of the polymers in water-solvent mixtures indicated an optimal water content of 2.5 wt% of water. (paper)

Point and interval forecasts of mortality rates and life expectancy: A comparison of ten principal component methods

Directory of Open Access Journals (Sweden)

Han Lin Shang

2011-07-01

Full Text Available Using the age- and sex-specific data of 14 developed countries, we compare the point and interval forecast accuracy and bias of ten principal component methods for forecasting mortality rates and life expectancy. The ten methods are variants and extensions of the Lee-Carter method. Based on one-step forecast errors, the weighted Hyndman-Ullah method provides the most accurate point forecasts of mortality rates and the Lee-Miller method is the least biased. For the accuracy and bias of life expectancy, the weighted Hyndman-Ullah method performs the best for female mortality and the Lee-Miller method for male mortality. While all methods underestimate variability in mortality rates, the more complex Hyndman-Ullah methods are more accurate than the simpler methods. The weighted Hyndman-Ullah method provides the most accurate interval forecasts for mortality rates, while the robust Hyndman-Ullah method provides the best interval forecast accuracy for life expectancy.

Physiological and phylogenetic characterization of a stable benzene-degrading, chlorate-reducing microbial community

NARCIS (Netherlands)

Weelink, S.A.B.; Tan, N.C.G.; Broeke, H. ten; Doesburg, W. van; Langenhoff, A.A.M.; Gerritse, J.; Stams, A.J.M.

2007-01-01

A stable anoxic enrichment culture was obtained that degraded benzene with chlorate as an electron acceptor. The benzene degradation rate was 1.65 mM benzene per day, which is similar to reported aerobic benzene degradation rates but 20-1650 times higher than reported for anaerobic benzene

Mass spectrometry analysis of proteome-wide proteolytic post-translational degradation of proteins

OpenAIRE

Shen, Yufeng; Hixson, Kim K.; Tolić, Nikola; Camp, David G.; Purvine, Samuel O.; Moore, Ronald J.; Smith, Richard D.

2008-01-01

Protein proteolytic degradation is an essential component to proper cell function and its life cycle. Here, we study the protein degradation in yeast Saccharomyces cerevisiae cells on a proteome-wide scale by detection of the intermediate peptides produced from the intracellular degradation of proteins using sequencing-based tandem mass spectrometry. By tracing the detected ~1,100 peptides and their ~200 protein substrate origins we obtain evidence for new insights into the proteome-wide prot...

Degradation and half-life of DNA present in biomass from a genetically-modified organism during land application.

Science.gov (United States)

Halter, Mathew C; Zahn, James A

2017-02-01

White biotechnology has made a positive impact on the chemical industry by providing safer, more efficient chemical manufacturing processes that have reduced the use of toxic chemicals, harsh reaction conditions, and expensive metal catalysts, which has improved alignment with the principles of Green Chemistry. The genetically-modified (GM) biocatalysts that are utilized in these processes are typically separated from high-value products and then recycled, or eliminated. Elimination routes include disposal in sanitary landfills, incineration, use as a fuel, animal feed, or reuse as an agricultural soil amendment or other value-added products. Elimination routes that have the potential to impact the food chain or environment have been more heavily scrutinized for the fate and persistence of biological products. In this study, we developed and optimized a method for monitoring the degradation of strain-specific DNA markers from a genetically-modified organism (GMO) used for the commercial production of 1,3-propanediol. Laboratory and field tests showed that a marker for heterologous DNA in the GM organism was no longer detectable by end-point polymerase chain reaction (PCR) after 14 days. The half-life of heterologous DNA was increased by 17% (from 42.4 to 49.7 h) after sterilization of the soil from a field plot, which indicated that abiotic factors were important in degradation of DNA under field conditions. There was no evidence for horizontal transfer of DNA target sequences from the GMO to viable organisms present in the soil.

Bioremediation of hydrocarbon degradation in a petroleum-contaminated soil and microbial population and activity determination.

Science.gov (United States)

Wu, Manli; Li, Wei; Dick, Warren A; Ye, Xiqiong; Chen, Kaili; Kost, David; Chen, Liming

2017-02-01

Bioremediation of hydrocarbon degradation in petroleum-polluted soil is carried out by various microorganisms. However, little information is available for the relationships between hydrocarbon degradation rates in petroleum-contaminated soil and microbial population and activity in laboratory assay. In a microcosm study, degradation rate and efficiency of total petroleum hydrocarbons (TPH), alkanes, and polycyclic aromatic hydrocarbons (PAH) in a petroleum-contaminated soil were determined using an infrared photometer oil content analyzer and a gas chromatography mass spectrometry (GC-MS). Also, the populations of TPH, alkane, and PAH degraders were enumerated by a modified most probable number (MPN) procedure, and the hydrocarbon degrading activities of these degraders were determined by the Biolog (MT2) MicroPlates assay. Results showed linear correlations between the TPH and alkane degradation rates and the population and activity increases of TPH and alkane degraders, but no correlation was observed between the PAH degradation rates and the PAH population and activity increases. Petroleum hydrocarbon degrading microbial population measured by MPN was significantly correlated with metabolic activity in the Biolog assay. The results suggest that the MPN procedure and the Biolog assay are efficient methods for assessing the rates of TPH and alkane, but not PAH, bioremediation in oil-contaminated soil in laboratory. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fungal bio-degradation of 14C-parathion

International Nuclear Information System (INIS)

Mohamed, G. A.; Abo-El Seoud, M. A.

2012-12-01

1 4 'C-parathion (670 Bq) was applied to mineral salt medium (MSM) to examine and evaluate its biodegradation by some fungi. The studied isolates were Alternaria alternate, Fusarium oxysporim and trichoderma viride. The inoculated media were incubated at 30 o C for periods of 2, 4, 6 and 8 days. Ta each interval, mycelia were separated from nutrient solution and extracted for its radioactivity. However, non extractable compounds were liberated by combustion. Quantitative and qualitative analysis were carried out for the radioactive compound in mycelia l extracts and residues as well as the fungal culture filtrate. Balance sheet for total recovered radioactive compounds was concluded 1 4 'C-parathion metabolism was expressed as original compound, polar metabolite, non polar metabolites and non extractable residues and then degradation rate was calculated. araesults indicated that there was continuous penetration for the radioactivity into mycelia tissues and the maximum, accumulation was recorded by Fusarium Oxysporium. The fungi under investigation showed considerable variations regarding their capacity to degrade the radioactive pesticide. Trichoderma viride exhibited the maximum capability to catabolism the the 1 4C -parathion as it exerted the maximum degradation rate. Fusarium and Alternate alter nata showed less degradation rates for the 1 4C - pesticide under investigation. (Author)

Degradation rate of sludge/fly ash mixture used as landfill liner; Nedbrytningshastigheten foer taetskikt uppbyggda av slam och aska

Energy Technology Data Exchange (ETDEWEB)

Wikman, Karin; Berg, Magnus [AaF-Process AB, Stockholm (Sweden); Svensson, Malin; Ecke, Holger [Luleaa Univ. of Technology (Sweden)

2005-10-01

In order to be able to use mixtures of ash and sludge as landfill liner an important aspect is to demonstrate that the degradation of organic matter is slow enough. Therefore, the goal of this project has been to find out for how long a landfill liner material of sludge and ash will be stable and keep its function. The degradation of organic material in two different mixtures of sludge and ash has been studied in laboratory experiments. The rate of degradation was then estimated for barriers of sludge and ash, taking into account construction techniques (mixture, compaction, water content), climate conditions (freezing, drying) and biological processes (NaN{sub 3} additive). The effect of the degradation on the permeability has also been quantified. Organic material may disappear for the landfill liner material through 1) initial leaching of soluble organic material, 2) leaching of organic material after chemical reactions or 3) evaporation during biological degradation. Bacterial activity was not found in the sludge/ash mixtures during the experiments. Therefore, the organic material is probably reduced mainly though leaching according to 1) and 2). The leached amount of TOC (total organic carbon) was measured for all samples of sludge/ash in several experimental cycles. The leached amount of TOC was compared to the initial amount of TOC in the material. The results show a small initial reduction of organic material through leaching but the TOC content in the material is then stabilized. In relation to the total weight of the material the leaching of TOC was similar for the mixtures with 80 % ash and 20 % ash. However, this means that a larger amount of TOC was leached out from the mixtures with a high ash content since the initial amount of organic material was smaller. General conclusions about which ash-sludge ratio that is suitable for a landfill liner material could not be drawn from the experiments from a degradation point of view. If the initial

[Degradation of 4-chlorophenol in aqueous solution by high-voltage pulsed discharge-ozone technology].

Science.gov (United States)

Wen, Yuezhong; Jiang, Xuanzhen; Liu, Weiping

2002-03-01

The combination of high voltage pulse discharge and ozonation as an advanced oxidation technology was used to investigate the degradation of 4-chlorophenol (4-CP) in water. The factors that affect the rate of degradation were discussed. The 1.95 x 10(-3) mol/L solutions of 4-CP were almost completely (96%) degraded after the discharge treatment of 30 min. The degradation of 4-CP was investigated as a function of the ozone concentration, radical scavenger and electrode distance. The rate of 4-CP degradation increases with an increase in ozone concentration and a decrease in the electrode distance from 20 mm to 10 mm. The presence of radical scavenger decreased the rate of 4-CP degradation.

Photocatalytic degradation of paraoxon-ethyl in aqueous solution using titania nanoparticulate film

Energy Technology Data Exchange (ETDEWEB)

Prasad, G.K., E-mail: gkprasad2001@yahoo.com; Ramacharyulu, P.V.R.K.; Kumar, J. Praveen; Srivastava, A.R.; Singh, Beer

2012-06-30

Photocatalytic degradation of paraoxon-ethyl (o,o-diethyl o-(4-nitrophenyl) phosphate), a well known surrogate of chemical warfare agents, in aqueous solution was studied by using titania nanoparticulate film. Reaction followed pseudo first order behaviour. Photolytic degradation reaction of paraoxon-ethyl demonstrated relatively low rate with a value of rate constant of 2.5 Multiplication-Sign 10{sup -3} min{sup -1}. Whereas, degradation reaction in the presence of titania nanoparticulate film and UV light displayed enhanced rate with a value of rate constant of 6.9 Multiplication-Sign 10{sup -3} min{sup -1} due to photocatalysis. Gas chromatography-mass spectrometry analysis showed the formation of p-nitrophenol, o,o-diethyl phosphonic acid, o-ethyl, diphosphonic acid, phosphoric acid, dimerized product of o,o-diethyl phosphonic acid, acetaldehyde, and carbon dioxide due to photocatalytic degradation of paraoxon-ethyl. It indicates that, photocatalytic degradation reaction begins with destruction of P-O-C bonds. Subsequently, P, C atoms were found to be oxidized gradually, and contributed to its photocatalytic degradation. - Highlights: Black-Right-Pointing-Pointer Synthesis of titania nanoparticles by sol-gel method. Black-Right-Pointing-Pointer Fabrication of titania nanoparticulate film by dip coating. Black-Right-Pointing-Pointer Paraoxon ethyl degradation reactions followed pseudo first order behaviour. Black-Right-Pointing-Pointer Paraoxon-ethyl degraded to non toxic compounds like CO{sub 2}, acetaldehyde, and nitrophenol.

Relative influence of age, resting heart rate and sedentary life style in short-term analysis of heart rate variability

OpenAIRE

E.R. Migliaro; P. Contreras; S. Bech; A. Etxagibel; M. Castro; R. Ricca; K. Vicente

2001-01-01

In order to assess the relative influence of age, resting heart rate (HR) and sedentary life style, heart rate variability (HRV) was studied in two different groups. The young group (YG) consisted of 9 sedentary subjects aged 15 to 20 years (YG-S) and of 9 nonsedentary volunteers (YG-NS) also aged 15 to 20. The elderly sedentary group (ESG) consisted of 16 sedentary subjects aged 39 to 82 years. HRV was assessed using a short-term procedure (5 min). R-R variability was calculated in the time-...

Control of the Protein Turnover Rates in Lemna minor

Science.gov (United States)

Trewavas, A.

1972-01-01

The control of protein turnover in Lemna minor has been examined using a method described in the previous paper for determining the rate constants of synthesis and degradation of protein. If Lemna is placed on water, there is a reduction in the rate constants of synthesis of protein and an increase (3- to 6-fold) in the rate constant of degradation. The net effect is a loss of protein from the tissue. Omission of nitrate, phosphate, sulfate, magnesium, or calcium results in increases in the rate constant of degradation of protein. An unusual dual effect of benzyladenine on the turnover constants has been observed. Treatment of Lemna grown on sucrose-mineral salts with benzyladenine results in alterations only in the rate constant of synthesis. Treatment of Lemna grown on water with benzyladenine alters only the rate constant of degradation. Abscisic acid on the other hand alters both rate constants of synthesis and degradation of protein together. Inclusion of growth-inhibiting amino acids in the medium results in a reduction in the rate constants of synthesis and increases in the rate constant of degradation of protein. It is concluded that the rate of turnover of protein in Lemna is very dependent on the composition of the growth medium. Conditions which reduce growth rates also reduce the rates of synthesis of protein and increase those of degradation. PMID:16657895

Life Insurance Take-Up Rate Influencing Factors Comparison between Malaysia and Japan

Directory of Open Access Journals (Sweden)

Silvana Kardinar Wijayanti

2016-08-01

Full Text Available This study will investigate the factors that influence take-up rates within the Malaysian Life Insurance industry to discover potential opportunities and limitations. For comparative purposes, the study is modelled on Power (2013 who examined four factors affecting customer satisfaction in life insurance in Japan (product, price, customer services and procedures and documentation. This study is exploratory in nature using both secondary research and primary data from questionnaires. The main finding was “Product offerings” being the most significant variation, both an opportunity and limitation, due to the relative maturity, experience and changing trends within the insurance market of Japan, conversely growth, infancy and different dynamics in Malaysia.

A 'slow pace of life' in Australian old-endemic passerine birds is not accompanied by low basal metabolic rates.

Science.gov (United States)

Bech, Claus; Chappell, Mark A; Astheimer, Lee B; Londoño, Gustavo A; Buttemer, William A

2016-05-01

Life history theory suggests that species experiencing high extrinsic mortality rates allocate more resources toward reproduction relative to self-maintenance and reach maturity earlier ('fast pace of life') than those having greater life expectancy and reproducing at a lower rate ('slow pace of life'). Among birds, many studies have shown that tropical species have a slower pace of life than temperate-breeding species. The pace of life has been hypothesized to affect metabolism and, as predicted, tropical birds have lower basal metabolic rates (BMR) than temperate-breeding birds. However, many temperate-breeding Australian passerines belong to lineages that evolved in Australia and share 'slow' life-history traits that are typical of tropical birds. We obtained BMR from 30 of these 'old-endemics' and ten sympatric species of more recently arrived passerine lineages (derived from Afro-Asian origins or introduced by Europeans) with 'faster' life histories. The BMR of 'slow' temperate-breeding old-endemics was indistinguishable from that of new-arrivals and was not lower than the BMR of 'fast' temperate-breeding non-Australian passerines. Old-endemics had substantially smaller clutches and longer maximal life spans in the wild than new arrivals, but neither clutch size nor maximum life span was correlated with BMR. Our results suggest that low BMR in tropical birds is not functionally linked to their 'slow pace of life' and instead may be a consequence of differences in annual thermal conditions experienced by tropical versus temperate species.

Technical Viability of Battery Second Life: A Study from the Ageing Perspective

DEFF Research Database (Denmark)

Martinez-Laserna, Egoitz; Sarasketa-Zabala, Elixabet; Stroe, Daniel-Ioan

2018-01-01

of Lithium-ion (Li-ion) NMC/C battery State of Health (SOH) and ageing history over the second life performance, on two different applications: a residential demand management application and a power smoothing renewable integration application. The performance and degradation of second life batteries...... ageing history upon the second life battery performance and degradation. Thereby, proper monitoring and battery selection appears crucial to certify the technical viability of battery second life....

Atrazine degradation using chemical-free process of USUV: Analysis of the micro-heterogeneous environments and the degradation mechanisms

International Nuclear Information System (INIS)

Xu, L.J.; Chu, W.; Graham, Nigel

2014-01-01

Graphical abstract: - Highlights: • Two chemical-free AOP processes are combined to enhance atrazine degradation. • ATZ degradation in sonophotolytic process was analyzed using a previous proposed model. • The micro-bubble/liquid heterogeneous environments in sonolytic processes were investigated. • The salt effects on different sonolytic processes were examined. • ATZ degradation mechanisms were investigated and pathways were proposed. - Abstract: The effectiveness of sonolysis (US), photolysis (UV), and sonophotolysis (USUV) for the degradation of atrazine (ATZ) was investigated. An untypical kinetics analysis was found useful to describe the combined process, which is compatible to pseudo first-order kinetics. The heterogeneous environments of two different ultrasounds (20 and 400 kHz) were evaluated. The heterogeneous distribution of ATZ in the ultrasonic solution was found critical in determining the reaction rates at different frequencies. The presence of NaCl would promote/inhibit the rates by the growth and decline of “salting out” effect and surface tension. The benefits of combining these two processes were for the first time investigated from the aspect of promoting the intermediates degradation which were resistant in individual processes. UV caused a rapid transformation of ATZ to 2-hydroxyatrazine (OIET), which was insensitive to UV irradiation; however, US and USUV were able to degrade OIET and other intermediates through • OH attack. On the other hand, UV irradiation also could promote radical generation via H 2 O 2 decomposition, thereby resulting in less accumulation of more hydrophilic intermediates, which are difficult to degradation in the US process. Reaction pathways for ATZ degradation by all three processes are proposed. USUV achieved the greatest degree of ATZ mineralization with more than 60% TOC removed, contributed solely by the oxidation of side chains. Ammeline was found to be the only end-product in both US and USUV

Atrazine degradation using chemical-free process of USUV: Analysis of the micro-heterogeneous environments and the degradation mechanisms

Energy Technology Data Exchange (ETDEWEB)

Xu, L.J., E-mail: xulijie827@gmail.com [Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Chu, W., E-mail: cewchu@polyu.edu.hk [Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Graham, Nigel, E-mail: n.graham@imperial.ac.uk [Department of Civil and Environmental Engineering, Imperial College London, South Kensington Campus, London SW7 2AZ (United Kingdom)

2014-06-30

Graphical abstract: - Highlights: • Two chemical-free AOP processes are combined to enhance atrazine degradation. • ATZ degradation in sonophotolytic process was analyzed using a previous proposed model. • The micro-bubble/liquid heterogeneous environments in sonolytic processes were investigated. • The salt effects on different sonolytic processes were examined. • ATZ degradation mechanisms were investigated and pathways were proposed. - Abstract: The effectiveness of sonolysis (US), photolysis (UV), and sonophotolysis (USUV) for the degradation of atrazine (ATZ) was investigated. An untypical kinetics analysis was found useful to describe the combined process, which is compatible to pseudo first-order kinetics. The heterogeneous environments of two different ultrasounds (20 and 400 kHz) were evaluated. The heterogeneous distribution of ATZ in the ultrasonic solution was found critical in determining the reaction rates at different frequencies. The presence of NaCl would promote/inhibit the rates by the growth and decline of “salting out” effect and surface tension. The benefits of combining these two processes were for the first time investigated from the aspect of promoting the intermediates degradation which were resistant in individual processes. UV caused a rapid transformation of ATZ to 2-hydroxyatrazine (OIET), which was insensitive to UV irradiation; however, US and USUV were able to degrade OIET and other intermediates through • OH attack. On the other hand, UV irradiation also could promote radical generation via H{sub 2}O{sub 2} decomposition, thereby resulting in less accumulation of more hydrophilic intermediates, which are difficult to degradation in the US process. Reaction pathways for ATZ degradation by all three processes are proposed. USUV achieved the greatest degree of ATZ mineralization with more than 60% TOC removed, contributed solely by the oxidation of side chains. Ammeline was found to be the only end-product in both US

Quantifying radioxerostomia: salivary flow rate, examiner's score, and quality of life questionnaire

International Nuclear Information System (INIS)

Al-Nawas, B.; Al-Nawas, K.; Kunkel, M.; Groetz, K.A.

2006-01-01

Background and purpose: salivary flow rates alone are not sufficient to quantify all aspects of radioxerostomia. This is a problem in studies aiming to reduce radioxerostomia. The aim of this study was to evaluate the association between objectively measured salivary flow rate and subjective xerostomia ratings by the physician (RTOG scale) or the patients (quality of life [QoL] questionnaire). Patients and methods: in a case-control study patients who underwent recall for oral cancer were screened. Inclusion criteria for this diagnostic, noninterventional study were: history of oral carcinoma, surgical and radiation therapy, time interval from start of radiation therapy > 90 days, salivary glands within the radiation field. The control group consisted of patients, who had not received radiotherapy. RTOG salivary gland score, quality of life (EORTC QLQ-C30 and H and N35), and sialometry were recorded. Results: patients with RTOG score 0 had mean salivary flow rates of 0.3 ml/min, those with RTOG 1 0.12 ml/min, RTOG 2 0.02 ml/min, and RTOG 3 < 0.01 ml/min. RTOG score 4 (total fibrosis) did not occur. Based on salivary flow rates, all patients were grouped into xerostomia < 0.2 ml/min (30 patients) and nonxerostomia (twelve patients). QoL results revealed significant differences between patients with xerostomia and nonxerostomia for physical function, dyspnea, swallowing, social eating, dry mouth, nutritional support, and a tendency to higher values for appetite loss. Conclusion: the correlation between ''subjective'' QoL parameters and salivary flow was confirmed. The different subjective aspects of radioxerostomia seem to be better differentiated by the EORTC QoL questionnaire. (orig.)

Estimating the Biodegradation Kinetics by Mixed Culture Degrading Pyrene (Pyr

Directory of Open Access Journals (Sweden)

B. S. U. Ibn Abubakar

2017-02-01

Full Text Available Biodegradation and kinetics of Pyrene (Pyr degradation by a mixed culture previously isolated from hydrocarbon-polluted soil were conducted. Preliminary investigation on environmental factors affecting the degradation of Pyr such as temperature, pH and concentrations of Pyr was performed. These factors were optimised and established in aqueous experiments. In order to develop kinetics of Pyr degradation, an optimum temperature of 30oC and pH of 7.0 was used. Biodegradation kinetics was carried out, at first, using higher concentration between (100-700 ppm as sole source of carbon in mineral salt medium (MSM supplemented with 0.1% yeast extract. The result indicated that a range of concentration between (100-700 ppm inhibits the performance of the mixed culture. A concentration range between (10-100 ppm did not inhibit the growth of the mixed culture. A First-order rate constant, k was higher (0.0487 mg/lh with a substrate concentration of 20 ppm than other concentrations. The average degradation rate constant is 0.0029 mg/Lh for all the concentrations tested. This indicated that the mixed culture could degrade over 0.0696 ppm of Pyr per day. It also confirmed that kinetics of microbial degradation was partially fitted into Monod model. The data can be used to estimate biodegradation of Pyr by a mixed culture and preliminarily estimation of degradation rates.

In-Field Spatial Variability in the Degradation of the Phenyl-Urea Herbicide Isoproturon Is the Result of Interactions between Degradative Sphingomonas spp. and Soil pH

Science.gov (United States)

Bending, Gary D.; Lincoln, Suzanne D.; Sørensen, Sebastian R.; Morgan, J. Alun W.; Aamand, Jens; Walker, Allan

2003-01-01

Substantial spatial variability in the degradation rate of the phenyl-urea herbicide isoproturon (IPU) [3-(4-isopropylphenyl)-1,1-dimethylurea] has been shown to occur within agricultural fields, with implications for the longevity of the compound in the soil, and its movement to ground- and surface water. The microbial mechanisms underlying such spatial variability in degradation rate were investigated at Deep Slade field in Warwickshire, United Kingdom. Most-probable-number analysis showed that rapid degradation of IPU was associated with proliferation of IPU-degrading organisms. Slow degradation of IPU was linked to either a delay in the proliferation of IPU-degrading organisms or apparent cometabolic degradation. Using enrichment techniques, an IPU-degrading bacterial culture (designated strain F35) was isolated from fast-degrading soil, and partial 16S rRNA sequencing placed it within the Sphingomonas group. Denaturing gradient gel electrophoresis (DGGE) of PCR-amplified bacterial community 16S rRNA revealed two bands that increased in intensity in soil during growth-linked metabolism of IPU, and sequencing of the excised bands showed high sequence homology to the Sphingomonas group. However, while F35 was not closely related to either DGGE band, one of the DGGE bands showed 100% partial 16S rRNA sequence homology to an IPU-degrading Sphingomonas sp. (strain SRS2) isolated from Deep Slade field in an earlier study. Experiments with strains SRS2 and F35 in soil and liquid culture showed that the isolates had a narrow pH optimum (7 to 7.5) for metabolism of IPU. The pH requirements of IPU-degrading strains of Sphingomonas spp. could largely account for the spatial variation of IPU degradation rates across the field. PMID:12571001

THE FTIR STUDIES OF PHOTO-OXIDATIVE DEGRADATION OF POLYPROPYLENE

Institute of Scientific and Technical Information of China (English)

WEN Zaiqing; HU Xingzhou; SHEN Deyan

1988-01-01

The photo-oxidative degradation process of polypropylene film containing iron ions was investigated via FTIR and absorbance substraction technique. It is shown that the iron ions play an important role in the decomposition of hydroperoxide and the increase of the degradation rate of polypropylene film. Theamorphous region of PP film undergoes degradation prior to the crystalline one.

Quantitative framework for ordered degradation of APC/C substrates.

Science.gov (United States)

Lu, Dan; Girard, Juliet R; Li, Weihan; Mizrak, Arda; Morgan, David O

2015-11-16

During cell-cycle progression, substrates of a single master regulatory enzyme can be modified in a specific order. Here, we used experimental and computational approaches to dissect the quantitative mechanisms underlying the ordered degradation of the substrates of the ubiquitin ligase APC/C(Cdc20), a key regulator of chromosome segregation in mitosis. We show experimentally that the rate of catalysis varies with different substrates of APC/C(Cdc20). Using a computational model based on multi-step ubiquitination, we then show how changes in the interaction between a single substrate and APC/C(Cdc20) can alter the timing of degradation onset relative to APC/C(Cdc20) activation, while ensuring a fast degradation rate. Degradation timing and dynamics depend on substrate affinity for the enzyme as well as the catalytic rate at which the substrate is modified. When two substrates share the same pool of APC/C(Cdc20), their relative enzyme affinities and rates of catalysis influence the partitioning of APC/C(Cdc20) among substrates, resulting in substrate competition. Depending on how APC/C(Cdc20) is partitioned among its substrates, competition can have minor or major effects on the degradation of certain substrates. We show experimentally that increased expression of the early APC/C(Cdc20) substrate Clb5 does not delay the degradation of the later substrate securin, arguing against a role for competition with Clb5 in establishing securin degradation timing. The degradation timing of APC/C(Cdc20) substrates depends on the multi-step nature of ubiquitination, differences in substrate-APC/C(Cdc20) interactions, and competition among substrates. Our studies provide a conceptual framework for understanding how ordered modification can be established among substrates of the same regulatory enzyme, and facilitate our understanding of how precise temporal control is achieved by a small number of master regulators to ensure a successful cell division cycle.

Evaluation of cable aging degradation based on plant operating condition

International Nuclear Information System (INIS)

Kim, Jong-Seog

2005-01-01

Extending the lifetime of nuclear power plant [(hereafter referred simply as ''NPP'')] is one of the most important concerns in the world nuclear industry. Cables are one of the long live items which have not been considered to be replaced during the design life of NPP. To extend the cable life beyond the design life, we need to prove that the design life is too conservative compared with the actual aging. Condition monitoring is one of the useful ways for evaluating the aging condition of cable. In order to simulate the natural aging in nuclear power plant, a study on accelerated aging needs to be conducted first. In this paper, evaluations of mechanical aging degradation for cable jacket were performed after accelerated aging under the continuous heating and intermittent heating. Contrary to general expectation, the intermittent heating to cable jacket showed low aging degradation, 50% break-elongation and 60% indenter modulus, compared with continuous heating. With the plant maintenance period of 1 month after every 12 or 18 months operation, we can easily deduce that the life time of cable jacket can be extended much longer than estimated through the general EQ (Environmental Qualification) test, which adopts continuous accelerated aging for determining cable life. Therefore, a systematic approach which considers the actual environment condition of nuclear power plant is required for determining the life of cables. (author)

Degradation of acrylamide by the UV/chlorine advanced oxidation process.

Science.gov (United States)

Gao, Ze-Chen; Lin, Yi-Li; Xu, Bin; Pan, Yang; Xia, Sheng-Ji; Gao, Nai-Yun; Zhang, Tian-Yang; Chen, Ming

2017-11-01

The degradation of acrylamide (AA) during UV/chlorine advanced oxidation process (AOP) was investigated in this study. The degradation of AA was negligible during UV irradiation alone. However, AA could be effectively degraded and mineralized during UV/chlorination due to the generation of hydroxyl radicals (OH). The degradation kinetics of AA during UV/chlorination fitted the pseudo-first order kinetics with the rate constant between AA and OH radicals being determined as 2.11 × 10 9  M -1  s -1 . The degradation rate and mineralization of AA during UV/chlorination were significantly promoted at acidic conditions as well as increasing chlorine dosage. The volatile degradation products of AA during UV/chlorination were identified using gas chromatography-mass spectrometry and the degradation pathways were then proposed accordingly. The formation of disinfection by-products (DBPs) in Milli-Q water and tap water during UV/chlorination of AA was also investigated. The DBPs included chloroform, dichloroacetonitrile, trichloroacetonitrile, 2,2-dichloroacetamide and 2,2,2-trichloroacetamide. Furthermore, the variations of AA degradation during UV/chlorination in different real water samples were evaluated. Copyright © 2017 Elsevier Ltd. All rights reserved.

Kinetics and mechanism for the sonochemical degradation of a nonionic surfactant.

Science.gov (United States)

Singla, Ritu; Grieser, Franz; Ashokkumar, Muthupandian

2009-03-26

The sonolytic degradation of the nonionic surfactant, octaethylene glycol monododecyl ether (C(12)E(8)), has been studied at various initial concentrations below and above its critical micelle concentration (CMC). It has been observed that the degradation rate increases with an increase in the initial concentration of the surfactant until the CMC is reached. Above the CMC an almost constant degradation rate is observed, suggesting that the surfactant in its monomer form is involved in the degradation process. The degradation process of C(12)E(8) involves two distinct primary processes occurring at the bubble/solution interface: (a) hydroxylation/oxidation of the surfactant and (b) pyrolytic fragmentation of the surfactant. The oxidative cleavage of ethylene oxide units provides evidence for OH radical attack. Hydroxylation of the ethoxy chain gives rise to various short-chain carboxyalkyl-polyethylene glycol intermediates. The polyethylene glycol chain formed, due to the scission of the C(12)E(8) molecule, undergoes rapid hydroxylation/oxidation to yield simple compounds that have the potential to undergo further degradation. The detection of multiple intermediates indicates that several processes affect the complete degradation pathways of the surfactant molecule. TOC analysis, however, indicates that the sonolytic mineralization of the surfactant is difficult to achieve at reasonable rates due to the relatively low surface activity of the degradation products formed during sonolysis.

Working session 1: Tubing degradation

International Nuclear Information System (INIS)

Kharshafdjian, G.; Turluer, G.

1997-01-01

A general introductory overview of the purpose of the group and the general subject area of SG tubing degradation was given by the facilitator. The purpose of the session was described as to open-quotes develop conclusions and proposals on regulatory and technical needs required to deal with the issues of SG tubing degradation.close quotes Types, locations and characteristics of tubing degradation in steam generators were briefly reviewed. The well-known synergistic effects of materials, environment, and stress and strain/strain rate, subsequently referred to by the acronym open-quotes MESSclose quotes by some of the group members, were noted. The element of time (i.e., evolution of these variables with time) was emphasized. It was also suggested that the group might want to consider the related topics of inspection capabilities, operational variables, degradation remedies, and validity of test data, and some background information in these areas was provided. The presentation given by Peter Millet during the Plenary Session was reviewed; Specifically, the chemical aspects and the degradation from the secondary side of the steam generator were noted. The main issues discussed during the October 1995 EPRI meeting on secondary side corrosion were reported, and a listing of the potential SG tube degradations was provided and discussed

Carbazole degradation in the soil microcosm by tropical bacterial strains

Directory of Open Access Journals (Sweden)

Lateef B. Salam

2015-01-01

Full Text Available In a previous study, three bacterial strains isolated from tropical hydrocarbon-contaminated soils and phylogenetically identified as Achromobacter sp. strain SL1, Pseudomonassp. strain SL4 and Microbacterium esteraromaticum strain SL6 displayed angular dioxygenation and mineralization of carbazole in batch cultures. In this study, the ability of these isolates to survive and enhance carbazole degradation in soil were tested in field-moist microcosms. Strain SL4 had the highest survival rate (1.8 x 107 cfu/g after 30 days of incubation in sterilized soil, while there was a decrease in population density in native (unsterilized soil when compared with the initial population. Gas chromatographic analysis after 30 days of incubation showed that in sterilized soil amended with carbazole (100 mg/kg, 66.96, 82.15 and 68.54% were degraded by strains SL1, SL4 and SL6, respectively, with rates of degradation of 0.093, 0.114 and 0.095 mg kg−1 h−1. The combination of the three isolates as inoculum in sterilized soil degraded 87.13% carbazole at a rate of 0.121 mg kg−1 h−1. In native soil amended with carbazole (100 mg/kg, 91.64, 87.29 and 89.13% were degraded by strains SL1, SL4 and SL6 after 30 days of incubation, with rates of degradation of 0.127, 0.121 and 0.124 mg kg−1h−1, respectively. This study successfully established the survivability (> 106 cfu/g detected after 30 days and carbazole-degrading ability of these bacterial strains in soil, and highlights the potential of these isolates as seed for the bioremediation of carbazole-impacted environments.

Contaminant degradation by irradiated semiconducting silver chloride particles: kinetics and modelling.

Science.gov (United States)

Ma, Tian; Garg, Shikha; Miller, Christopher J; Waite, T David

2015-05-15

The kinetics and mechanism of light-mediated formic acid (HCOO(-)) degradation in the presence of semiconducting silver chloride particles are investigated in this study. Our experimental results show that visible-light irradiation of AgCl(s) results in generation of holes and electrons with the photo-generated holes and its initial oxidation product carbonate radical, oxidizing HCOO(-) to form CO2. The HCOO(-) degradation rate increases with increase in silver concentration due to increase in rate of photo-generation of holes while the increase in chloride concentration decreases the degradation rate of HCOO(-) as a result of the scavenging of holes by Cl(-), thereby resulting in decreased holes and carbonate radical concentration. The results obtained indicate that a variety of other solution conditions including dioxygen concentration, bicarbonate concentration and pH influence the availability of holes and hence the HCOO(-) degradation rate in a manner consistent with our understanding of key processes. Based on our experimental results, we have developed a kinetic model capable of predicting AgCl(s)-mediated HCOO(-) photo-degradation over a wide range of conditions. Copyright © 2014 Elsevier Inc. All rights reserved.

A study on the influence of track discontinuities on the degradation of the geometric quality supported by GPR

Science.gov (United States)

Paixao, Andre; Fontul, Simona; Salcedas, Tânia; Marques, Margarida

2017-04-01

It is known that locations in the track denoting sudden structural changes induce dynamic amplifications in the train-track interaction, thus leading to higher impact loads from trains, which in turn promote a faster development of track defects and increase the degradation of components. Consequently, a reduction in the quality of service can be expected at such discontinuities in the track, inducing higher maintenance costs and decreasing the life-cycle of components. To finding actual evidences on how track discontinuities influence the degradation of the geometric quality, a 50-km long railway section is used as case study. The track geometry data obtained with a recording car is firstly characterized according to the European standard series EN 13848. Then, the results of successive surveys are analysed, making use of various tools such as the standard deviation with moving windows of different sizes and calculating degradation rates. The GPR data was also analysed at the locations corresponding to track discontinuities aiming at better identifying situations where sudden changes occur regarding either the structural characteristics or the track behaviour over the years. The results indicate that the geometric quality degrades faster at locations denoting discontinuities in the track, such as changes in track components, approaches to bridges, tunnels, etc. This behaviour suggests that these sites should be monitored more carefully in the scope of asset management activities in order to maximize the life-cycle of the track and its components. This work is a contribution to COST (European COoperation on Science and Technology) Action TU1208 "Civil Engineering Applications of Ground Penetrating Radar".

Novel function of the endoplasmic reticulum degradation-enhancing α-mannosidase-like proteins in the human hepatitis B virus life cycle, mediated by the middle envelope protein.

Science.gov (United States)

Lazar, Catalin; Uta, Mihaela; Petrescu, Stefana Maria; Branza-Nichita, Norica

2017-02-01

Cells replicating the human hepatitis B virus (HBV) express high levels of degradation-enhancing α-mannosidase-like proteins (EDEMs), a family of proteins involved in the endoplasmic reticulum associated degradation, one of the pathways activated during the unfolded protein response. Owing to their α-1,2 mannosidase activity, the EDEM1-3 proteins are able to process the N-linked glycans of misfolded or incompletely folded proteins, providing the recognition signal for their subsequent degradation. The HBV small (S), medium (M), and large (L) surface proteins bear an N-linked glycosylation site in the common S domain that is partially occupied in all proteins. The M protein contains an additional site in its preS2 domain, which is always functional. Here, we report that these oligosaccharides are processed by EDEMs, more efficiently by EDEM3, which induces degradation of L and S proteins, accompanied by a reduction of subviral particles production. In striking contrast, M not only is spared from degradation but its trafficking is also accelerated leading to an improved secretion. This unusual behavior of the M protein requires strictly the mannose trimming of the preS2 N-linked glycan. Furthermore, we show that HBV secretion is significantly inhibited under strong endoplasmic reticulum stress conditions when M expression is prevented by mutagenesis of the viral genome. These observations unfold unique properties of the M protein in the HBV life cycle during unfolded protein response and point to alternative mechanisms employed by EDEMs to alleviate this stress in case of necessity by promoting glycoprotein trafficking rather than degradation. © 2016 John Wiley & Sons Ltd.

Aging management and life assessment of buried commodities in nuclear power plants

International Nuclear Information System (INIS)

Park, J. H.; Jung, I. S.; Jo, H. S.; Kim, M. G.; Kim, S. T.; Lee, S. S.

2000-01-01

General field survey, inspection and life assessment were performed to establish effective aging management program of buried commodities in nuclear power plant. Basic informations on material characteristics, aging degradation experiences and maintenance history were gathered. Considering their degradation effects on power operation or safety, buried commodities were screened for the aging management priority. Various inspection techniques were applied in field survey and inspection, and their results were incorporated in the life assessment of buried commodities. In the aspect of aging degradation, general status of buried commodities were considered still sound while some revealed local degradation

Radiation-induced degradation of organic pollutants in wastewater

International Nuclear Information System (INIS)

Bagyo, A.N.M.; Lindu, W.A.; Sadjirun, S.; Winarno, E.K.; Widayat, E.; Aryanti; Winarno, H.

2001-01-01

The degradation and decolouration of organic pollutants, i.e. dye stuffs and phenolic compounds, by gamma irradiation have been studied. First, samples from effluent of textile industry were taken to be irradiated at a certain condition. Irradiation was done after dissolving the samples five times with distilled water in laboratory scale, followed by upscaling those samples into 5 litre in volume. Irradiation was done at a dose of 0- 25 kGy, aerated and a dose rate of 5 kGy/h. The parameters examined were the change of absorption spectra. COD (Chemical Oxygen Demand), the percentage of the degradation, the change of pH and degradation product using HPLC. It was demonstrated that the dilution of sample enhanced the degradation and decreased the COD values. The degradation product of textile wastewater is mainly oxalic acid. Second, the effects of radiation on aerated phenolic compounds mixture, i.e. resorcinol, o-cresol and m- cresol were done. Individual phenol was studied followed by mixture of the phenolic compounds. Irradiation was done in aerated condition with doses of 0-10 kGy, dose rate of 5 kGy/h and pH range from 3 to 12. The initial concentration of resorcinol, o-cresol and w-cresol were 50 ppm and 60 ppm for phenolic compounds mixture, respectively. Parameters examined were absorption spectrum, pH, and degradation products. The uv-vis absorption of the solution were observed before and after irradiation. HPLC was used to determine the products of degradation. Degradation of resorcinol, w-cresol and o-cresol could be achieved at dose of 6 kGy at pH 9, while o-cresol in acid condition (pH 3). The degree of degradation for resorcinol, w-cresol and o-cresol at above conditions were 90%, 88% and 45%, respectively. Degradation of phenolic compound mixture occurred at a dose of 7.5 kGy and pH 9', at this condition almost 99% of phenolic compounds degraded. Oxalic acid was the main degradation product. (author)

The effect of starch-garlic powder ratio on degradation rate of Gadung starch bioplastic

Science.gov (United States)

Mairiza, L.; Mariana; Ramadhany, M.; Feviyussa, C. A.

2018-03-01

Bioplastic is one of the solutions for environmental problems caused by plastics waste. Utilization of toxic gadung starch in the manufacturing of bioplastic would be as an alternative, due to gadung bulb has high starch content, and it is still not used optimally. This research aimed to learn about the using of gadung starch-mixed with garlic powder of making biodegradable plastic packaging. Also, to observe the duration of degradation, as a level of biodegradability of plastic film produced. The method used making this bioplastic was casting method. The variables used in this study were the ratios of starch and powdered garlic, were 10:0; 8:2; 6:4, and the concentration of garlic powder were 2%; 4%; 6%; and 8 %. The degradation test was done by soil burial test. The results of the soil burial test shown that the film was more rapidly degraded at ratio of 6: 4 compared to the ratio of 8: 2 and 10: 0. The results shown that bioplastic at the starch-garlic powder ratio of 10: 0 was decomposed in 21 days, at the the ratio of 8:2 was 15 days, while at the ratio of 6:4, the plastic film was degraded in the 11 days.

Radiolytic degradation of sorbic acid in isolated systems

International Nuclear Information System (INIS)

Thakur, B.R.; Trehan, I.R.; Arya, S.S.

1990-01-01

Effect of Co(60) gamma-irradiation on stability of sorbic acid (SA) in solutions, dough and chapaties has been investigated. SA was highly susceptible to radiolytic degradation in aqueous systems. Rate of degradation decreased with rise in pH. Sugars, hydrocolloids except pectin, citric acid, lactic acid, malic acid, arginine and threonine, catalyzed degradation while oxalic acid, maleic acid, Cu2+, nitrite, nitrate and phthalate had protective effects. SA was more stable in alcohols and vegetable oils than in aqueous solutions. In wheat flour radiolytic degradation of SA was less at lower moisture. Relatively SA was more stable in chapaties than in dough. Gelatinization and addition of oil in dough reduced degradation of SA

Photocatalytic and photoelectrocatalytic degradation of the drug omeprazole on nanocrystalline titania films in alkaline media: Effect of applied electrical bias on degradation and transformation products

Energy Technology Data Exchange (ETDEWEB)

Tantis, Iosif [Department of Chemical Engineering, University of Patras, Caratheodory 1, University Campus, GR-26504 Patras (Greece); Bousiakou, Leda [Department of Physics and Astronomy, King Saud University, Riyadh (Saudi Arabia); Department of Automation Engineering, Technological Educational Institute of Pireaus, GR-12244 Athens (Greece); Frontistis, Zacharias; Mantzavinos, Dionissios [Department of Chemical Engineering, University of Patras, Caratheodory 1, University Campus, GR-26504 Patras (Greece); Konstantinou, Ioannis; Antonopoulou, Maria [Department of Environmental and Natural Resources Management, University of Patras, GR-30100 Agrinio (Greece); Karikas, George-Albert [Department of Medical Laboratories Technology, Technological Educational Institute of Athens, 12210 Athens (Greece); Lianos, Panagiotis, E-mail: lianos@upatras.gr [Department of Chemical Engineering, University of Patras, Caratheodory 1, University Campus, GR-26504 Patras (Greece); FORTH/ICE-HT, P.O. Box 1414, GR-26504 Patras (Greece)

2015-08-30

Highlights: • Photocatalytic and photoelectrocatalytic degradation of the proton pump omeprazole. • Improvement of photocatalysis rate by applying a moderate forward bias. • Highlighting of the advantages of photoelectrocatalysis in a straightforward manner. • HPLC and HR-LC–MS analysis of transformation products. - Abstract: Photocatalytic and photoelectrocatalytic degradation of the drug omeprazole has been studied in the presence of nanocrystalline titania films supported on glass slides or transparent FTO electrodes in alkaline environment. Its photocatalytic degradation rate was assessed by its UV absorbance and by HPLC, while its transformation products were analyzed by HR-LC–MS. Based on UV absorbance, omeprazole can be photocatalytically degraded at an average rate of 6.7 × 10{sup −4} min{sup −1} under low intensity UVA irradiation of 1.5 mW cm{sup −2} in the presence of a nanoparticulate titania film. This corresponds to degradation of 1.4 mg of omeprazole per gram of the photocatalyst per liter of solution per hour. The photodegradation rate can be accelerated in a photoelectrochemical cell by applying a forward bias. In this case, the maximum rate reached under the present conditions was 11.6 × 10{sup −4} min{sup −1} by applying a forward bias of +0.6 V vs. Ag/AgCl. Four major transformation products were successfully identified and their profiles were followed by HR-LC–MS. The major degradation path includes the scission of the sulfoxide bridge into the corresponding pyridine and benzimidazole ring derivates and this is accompanied by the release of sulfate anions in the reaction mixture.

Advanced Oxidation Degradation of Diclofenac

International Nuclear Information System (INIS)

Cooper, William J.; Song Weihua

2012-01-01

Advanced oxidation/reduction processes (AO/RPs), utilize free radical reactions to directly degrade chemical contaminants as an alternative to traditional water treatment. This study reports the absolute rate constants for reaction of diclofenac sodium and the model compound (2, 6-dichloraniline) with the two major AO/RP radicals; the hydroxyl radical (•OH) and hydrated electron (e - aq ). The bimolecular reaction rate constants (M -1 s -1 ) for diclofenac for •OH was (9.29 ± 0.11) x 10 9 , and, for e- aq was (1.53 ± 0.03) x10 9 . Preliminary degradation mechanisms are suggested based on product analysis using 60 Co γ-irradiation and LC-MS for reaction by-product identification. The toxicity of products was evaluated using the Vibrio fischeri luminescent bacteria method. (author)

Method and apparatus to predict the remaining service life of an operating system

Science.gov (United States)

Greitzer, Frank L.; Kangas, Lars J.; Terrones, Kristine M.; Maynard, Melody A.; Pawlowski, Ronald A. , Ferryman; Thomas A.; Skorpik, James R.; Wilson, Bary W.

2008-11-25

A method and computer-based apparatus for monitoring the degradation of, predicting the remaining service life of, and/or planning maintenance for, an operating system are disclosed. Diagnostic information on degradation of the operating system is obtained through measurement of one or more performance characteristics by one or more sensors onboard and/or proximate the operating system. Though not required, it is preferred that the sensor data are validated to improve the accuracy and reliability of the service life predictions. The condition or degree of degradation of the operating system is presented to a user by way of one or more calculated, numeric degradation figures of merit that are trended against one or more independent variables using one or more mathematical techniques. Furthermore, more than one trendline and uncertainty interval may be generated for a given degradation figure of merit/independent variable data set. The trendline(s) and uncertainty interval(s) are subsequently compared to one or more degradation figure of merit thresholds to predict the remaining service life of the operating system. The present invention enables multiple mathematical approaches in determining which trendline(s) to use to provide the best estimate of the remaining service life.

Kinetic Parameters of Thermal Degradation of Polymers

Institute of Scientific and Technical Information of China (English)

朱新生; 程嘉祺

2003-01-01

The derivative expressions between activation energy (E) and the temperature at the maximum mass loss rate(Tmax) and between activation energy (E) and exponent (N) were deduced in the light of Arrhenius theory. It was found that the increase of activation energy results in the decrease of exponent and the increase of Tmax. The kinetic parameters were involved in the analysis of the thermal degradation of several polymers. The degradation kinetics of these polymers well complied with the prediction of the derivative expressions for the polymer degradation with single mechanism dominated.

Degradation of materials and passivity

International Nuclear Information System (INIS)

Meisel, W.

1997-01-01

Demanding for a reduction in materials degradation is a serious problem all over the world. Moessbauer spectroscopy (MS) is, among others, a very valuable tool to follow many degradation processes. Evidently, Fe is the most important Moessbauer element considering the overall presence of iron in everyday life. MS may contribute to our knowledge about nearly all fields of materials degradation, chemical, mechanical, thermal, irradiative, etc. Following some general lines, corrosion is considered in particular. MS is applicable to investigate the bulk of materials as well as their surface layers with an information depth of ca. 250 nm. In general, it has to be applied as a surface sensitive method in combination with other relevant methods in order to get a detailed insight into ongoing processes. Some examples have been selected to elucidate the application of MS in this field. Another class of examples concerns attempts to prevent corrosion, i.e., the application of coatings and transforming chemicals. A very effective and most natural way to reduce corrosion is the passivation of materials. The effect of passive layers and their destruction by environmental influences are discussed using results of MS and related methods. It is outlined that passivity is not restricted to chemically treated metals but can be considered as a general concept for preventing different kinds of materials from degradation. (orig.)

The rate of source memory decline across the adult life span.

Science.gov (United States)

Cansino, Selene; Estrada-Manilla, Cinthya; Hernández-Ramos, Evelia; Martínez-Galindo, Joyce Graciela; Torres-Trejo, Frine; Gómez-Fernández, Tania; Ayala-Hernández, Mariana; Osorio, David; Cedillo-Tinoco, Melisa; Garcés-Flores, Lissete; Gómez-Melgarejo, Sandra; Beltrán-Palacios, Karla; Guadalupe García-Lázaro, Haydée; García-Gutiérrez, Fabiola; Cadena-Arenas, Yadira; Fernández-Apan, Luisa; Bärtschi, Andrea; Resendiz-Vera, Julieta; Rodríguez-Ortiz, María Dolores

2013-05-01

Previous studies have suggested that the ability to remember contextual information related to specific episodic experiences declines with advancing age; however, the exact moment in the adult life span when this deficit begins is still controversial. Source memory for spatial information was tested in a life span sample of 1,500 adults between the ages of 21 and 80. Initially, images of common objects were randomly presented on one quadrant of a screen while the participants judged whether they were natural or artificial. During the retrieval phase, these same images were mixed with new ones, and all images were displayed in the center of the screen. The participants were asked to judge whether each image was new or old, and whether it was old, to indicate in which quadrant of the screen it had originally been presented. Source accuracy decreased linearly with advancing age at a rate of 0.6% per year across all decades even after controlling for educational level; this decline was unaffected by sex. These results reveal that either spatial information becomes less efficiently bound to episodic representations over time or that the ability to retrieve this information decreases gradually throughout the adult life span.

Predictors of family caregiver ratings of patient quality of life in Alzheimer disease: cross-sectional results from the Canadian Alzheimer's Disease Quality of Life Study.

Science.gov (United States)

Naglie, Gary; Hogan, David B; Krahn, Murray; Black, Sandra E; Beattie, B Lynn; Patterson, Christopher; Macknight, Chris; Freedman, Morris; Borrie, Michael; Byszewski, Anna; Bergman, Howard; Streiner, David; Irvine, Jane; Ritvo, Paul; Comrie, Janna; Kowgier, Matthew; Tomlinson, George

2011-10-01

To assess whether the core symptoms of Alzheimer disease (AD) and caregiver factors consistently predict family caregiver ratings of patient quality of life (QOL) as assessed by a variety of QOL measures in a large national sample. : Cross-sectional. Fifteen dementia and geriatric clinics across Canada. : Family caregivers (n = 412) of community-living patients with AD of all severities. Caregiver ratings of patient QOL using three utility indexes, the European Quality of Life-5 Dimensions, Quality of Well-Being Scale and Health Utilities Index; a global QOL visual analogue scale; a disease-specific measure, the Quality of Life-Alzheimer's Disease; and a generic health status measure, the Short Form-36. Patient cognition was assessed with the cognitive subscale of the Alzheimer's Disease Assessment Scale and Mini-Mental State Examination, function with the Disability Assessment for Dementia, and behavioral and psychological symptoms with the Neuropsychiatric Inventory and the Geriatric Depression Scale. Caregiver burden was assessed with the Zarit Burden Interview and caregiver depression with the Center for Epidemiologic Studies Depression scale. One-way analysis of variance and fully adjusted multiple linear regression were used to assess the relationship between patient dementia symptom and caregiver variables with QOL ratings. In multivariable analyses, caregiver ratings of patient function and depressive symptoms were the only consistent independent predictors of caregiver-rated QOL across the QOL measures. Caregiver ratings of patient function and depression were consistent independent predictors of caregiver-rated QOL, using a spectrum of QOL measures, while measures of patient cognition and caregiver burden and depression were not. These findings support the continued use of caregiver ratings as an important source of information about patient QOL and endorse the inclusion in AD clinical trials of caregiver-rated measures of patient function, depression

Clofibric acid degradation in UV254/H2O2 process: effect of temperature.

Science.gov (United States)

Li, Wenzhen; Lu, Shuguang; Qiu, Zhaofu; Lin, Kuangfei

2010-04-15

The degradation of clofibric acid (CA) in UV(254)/H(2)O(2) process under three temperature ranges, i.e. T1 (9.0-11.5 degrees C), T2 (19.0-21.0 degrees C) and T3 (29.0-30.0 degrees C) was investigated. The effects of solution constituents including NO(3)(-) and HCO(3)(-) anions, and humic acid (HA) on CA degradation were evaluated in Milli-Q waters. CA degradation behaviors were simulated with the pseudo-first-order kinetic model and the apparent rate constant (k(ap)) and half-life time (t(1/2)) were calculated. The results showed that higher temperature would favor CA degradation, and CA degradation was taken place mostly by indirect oxidation through the formation of OH radicals in UV(254)/H(2)O(2) process. In addition, the effects of both NO(3)(-) and HCO(3)(-) anions at two selected concentrations (1.0x10(-3) and 0.1 mol L(-1)) and HA (20 mg L(-1)) on CA degradation were investigated. The results showed that HA had negative effect on CA degradation, and this effect was much more apparent under low temperature condition. On the other hand, the inhibitive effect on CA degradation at both lower and higher concentrations of bicarbonate was observed, and this inhibitive effect was much more apparent at higher bicarbonate concentration and lower temperature condition. While, at higher nitrate concentration the inhibitive effect on CA degradation under three temperature ranges was observed, and with the temperature increase this negative effect was apparently weakened. However, at lower nitrate concentration a slightly positive effect on CA degradation was found under T2 and T3 conditions. Moreover, when using a real wastewater treatment plant (WWTP) effluent spiked with CA over 99% of CA removal could be achieved under 30 degrees C within only 15 min compared with 40 and 80 min under 20 and 10 degrees C respectively, suggesting a significant promotion in CA degradation under higher temperature condition. Therefore, it can be concluded that temperature plays an

Evaluation of options for life cycle management of feeder cracking at the Point Lepreau Generating Station

International Nuclear Information System (INIS)

Gendron, T.S.; Slade, J.P.

2003-01-01

The CANDU industry has a predictive capability for most Heat Transport System (HTS) degradation issues that allows utilities to apply cost-effective maintenance programs. The standard approach for maintenance programs is focussed inspection and planned replacement. Some examples of degradation issues with deterministic failure rates are feeder thinning, and pressure tube elongation and deuterium ingress. However, the cracking observed in Point Lepreau Generating Station (PLGS) outlet feeder first bends is one notable exception to this behaviour. A predictive capability for feeder cracking does not currently exist for several reasons. First, the mechanism of feeder cracking, stress corrosion cracking (SCC), has to some degree a random nature. Second, although a probable environment causing cracking has been identified, the precise stress and environmental conditions for feeder crack initiation and propagation have not been defined. Finally, the very low incidence of feeder cracking observed to-date (four, all at PLGS) precludes a probabilistic or statistical prediction of failure rate. Generally, utilities select a Life Cycle Management Plan that ensures safe operation and has the lowest Net Present Value cost. In preparing a Feeder Life Cycle Management Plan, New Brunswick Power (NBP) has recognized that the Net Present Value cost is very sensitive to failure rate. Since the failure rate for feeder cracking is not well defined, the following three scenarios were considered to bound the probability of future failures at PLGS. (author)

Mineral induced mechanochemical degradation: the imazaquin case.

Science.gov (United States)

Nasser, Ahmed; Buchanovsky, Nadia; Gerstl, Zev; Mingelgrin, Uri

2009-03-01

The potential role of mechanochemical processes in enhancing degradation of imazaquin by soil components is demonstrated. The investigated components include montmorillonite saturated with Na(+), Ca(2+), Cu(2+)and Al(3+), Agsorb (a commercial clay mix), birnessite and hematite. The mechanical force applied was manual grinding of mixtures of imazaquin and the minerals, using mortar and pestle. The degradation rates of imazaquin in these mixtures were examined as a function of the following parameters: time of grinding, herbicide load (3.9, 8.9, 16.7 and 26.6 mg imazaquin per g mineral), temperature (10, 25, 40 and 70 degrees C), acidic/basic conditions, and dry or wet grinding. Dry grinding of imazaquin for 5 min with Al-montmorillonite or with hematite resulted in 56% and 71% degradation of the imazaquin, respectively. Wet grinding slightly reduced the degradation rate with hematite and entirely cancelled the enhancing effect of grinding with Al-montmorillonite. Wet grinding in the presence of the transition metals: Ni(2+), Cu(2+), Fe(3+) added as chlorides was carried out. Addition of Cu(2+) to Na-montmorillonite loaded with imazaquin was the most effective treatment in degrading imazaquin (more than 90% of the imazaquin degraded after 5 min of grinding). In this treatment, Cu-montmorillonite formation during the grinding process was confirmed by XRD and accordingly, grinding with Cu-montmorillonite gave similar degradation values. LC-MS analysis revealed that the mechanochemical transformation of imazaquin resulted in the formation of a dimer and several breakdown products. The reported results demonstrate once again that mechanochemical procedures offer a remediation avenue applicable to soils polluted with organic contaminants.

Emerging technology for component life assessment

International Nuclear Information System (INIS)

O'Donnell, W.J.; Porowski, J.S.

1991-01-01

In this paper operating plant component damage and failure experience is reviewed. Loading conditions such as thermal stratification and striping, turbulent flow and flow-induced vibrations are often found to limit useful life, even though such loadings were typically not considered when the components were designed. High cycle thermal and mechanical fatigue are identified as important damage mechanisms. A new method of correlating fatigue data and extrapolating to the very high cycle regime is described. The results of environmental degradation testing during the past fifteen years have shown that such effects are much more deleterious than previously assumed. Therefore environmental and aging effects must be taken into account in evaluating the reliability and dependability of components for extended periods of operation. Since most of the available data on environmental effects focuses on measured crack growth rates, methods of developing improved fatigue life evaluation methods which include environmental effects on crack growth rates are now being developed. Fatigue tests on polished specimens are characterized by nominal stress amplitudes over yield, where linear elastic fracture mechanics (da/dn vs Δk) methods, such as those used in the ASME Code, are not valid

Long-term storage life of light source modules by temperature cycling accelerated life test

International Nuclear Information System (INIS)

Sun Ningning; Tan Manqing; Li Ping; Jiao Jian; Guo Xiaofeng; Guo Wentao

2014-01-01

Light source modules are the most crucial and fragile devices that affect the life and reliability of the interferometric fiber optic gyroscope (IFOG). While the light emitting chips were stable in most cases, the module packaging proved to be less satisfactory. In long-term storage or the working environment, the ambient temperature changes constantly and thus the packaging and coupling performance of light source modules are more likely to degrade slowly due to different materials with different coefficients of thermal expansion in the bonding interface. A constant temperature accelerated life test cannot evaluate the impact of temperature variation on the performance of a module package, so the temperature cycling accelerated life test was studied. The main failure mechanism affecting light source modules is package failure due to solder fatigue failure including a fiber coupling shift, loss of cooling efficiency and thermal resistor degradation, so the Norris-Landzberg model was used to model solder fatigue life and determine the activation energy related to solder fatigue failure mechanism. By analyzing the test data, activation energy was determined and then the mean life of light source modules in different storage environments with a continuously changing temperature was simulated, which has provided direct reference data for the storage life prediction of IFOG. (semiconductor devices)

Degradation of dome cutting minerals in Hanford waste-13100

International Nuclear Information System (INIS)

Reynolds, Jacob G.; Huber, Heinz J.; Cooke, Gary A.

2013-01-01

At the Hanford Tank Farms, recent changes in retrieval technology require cutting new risers in several single-shell tanks. The Hanford Tank Farm Operator is using water jet technology with abrasive silicate minerals such as garnet or olivine to cut through the concrete and rebar dome. The abrasiveness of these minerals, which become part of the high-level waste stream, may enhance the erosion of waste processing equipment. However, garnet and olivine are not thermodynamically stable in Hanford waste, slowly degrading over time. How likely these materials are to dissolve completely in the waste before the waste is processed in the Waste Treatment and Immobilization Plant can be evaluated using theoretical analysis for olivine and collected direct experimental evidence for garnet. Based on an extensive literature study, a large number of primary silicates decompose into sodalite and cancrinite when exposed to Hanford waste. Given sufficient time, the sodalite also degrades into cancrinite. Even though cancrinite has not been directly added to any Hanford tanks during process times, it is the most common silicate observed in current Hanford waste. By analogy, olivine and garnet are expected to ultimately also decompose into cancrinite. Garnet used in a concrete cutting demonstration was immersed in a simulated supernate representing the estimated composition of the liquid retrieving waste from Hanford tank 241-C-107 at both ambient and elevated temperatures. This simulant was amended with extra NaOH to determine if adding caustic would help enhance the degradation rate of garnet. The results showed that the garnet degradation rate was highest at the highest NaOH concentration and temperature. At the end of 12 weeks, however, the garnet grains were mostly intact, even when immersed in 2 molar NaOH at 80 deg C. Cancrinite was identified as the degradation product on the surface of the garnet grains. In the case of olivine, the rate of degradation in the high-pH regimes

Degradation of Dome Cutting Minerals in Hanford Waste - 13100

Energy Technology Data Exchange (ETDEWEB)

Reynolds, Jacob G.; Cooke, Gary A.; Huber, Heinz J. [Washington River Protection Solutions, LLC, P.O. Box 850, Richland, WA 99352 (United States)

2013-07-01

At the Hanford Tank Farms, recent changes in retrieval technology require cutting new risers in several single-shell tanks. The Hanford Tank Farm Operator is using water jet technology with abrasive silicate minerals such as garnet or olivine to cut through the concrete and rebar dome. The abrasiveness of these minerals, which become part of the high-level waste stream, may enhance the erosion of waste processing equipment. However, garnet and olivine are not thermodynamically stable in Hanford waste, slowly degrading over time. How likely these materials are to dissolve completely in the waste before the waste is processed in the Waste Treatment and Immobilization Plant can be evaluated using theoretical analysis for olivine and collected direct experimental evidence for garnet. Based on an extensive literature study, a large number of primary silicates decompose into sodalite and cancrinite when exposed to Hanford waste. Given sufficient time, the sodalite also degrades into cancrinite. Even though cancrinite has not been directly added to any Hanford tanks during process times, it is the most common silicate observed in current Hanford waste. By analogy, olivine and garnet are expected to ultimately also decompose into cancrinite. Garnet used in a concrete cutting demonstration was immersed in a simulated supernate representing the estimated composition of the liquid retrieving waste from Hanford tank 241-C-107 at both ambient and elevated temperatures. This simulant was amended with extra NaOH to determine if adding caustic would help enhance the degradation rate of garnet. The results showed that the garnet degradation rate was highest at the highest NaOH concentration and temperature. At the end of 12 weeks, however, the garnet grains were mostly intact, even when immersed in 2 molar NaOH at 80 deg. C. Cancrinite was identified as the degradation product on the surface of the garnet grains. In the case of olivine, the rate of degradation in the high

Radiation induced degradation of dyes-An overview

International Nuclear Information System (INIS)

Rauf, M.A.; Ashraf, S. Salman

2009-01-01

Synthetic dyes are a major part of our life. Products ranging from clothes to leather accessories to furniture all depend on extensive use of organic dyes. An unfortunate side effect of extensive use of these chemicals is that huge amounts of these potentially carcinogenic compounds enter our water supplies. Various advanced oxidation processes (AOPs) including the use of high-energy radiation have been developed to degrade these compounds. In this review, dye decoloration and degradation as a result of its exposure to high energy radiation such as gamma radiation and pulsed electron beam are discussed in detail. The role of various transient species such as ·H, ·OH and e aq - are taken into account as reported by various researchers. Literature citations in this area show that e aq - is very effective in decolorization but is less active in the further degradation of the products formed. The degradation of the dyes is initiated exclusively by ·OH attack on electron-rich sites of the dye molecules. Additionally, various parameters that affect the efficiency of radiation induced degradation of dyes, such as effect of radiation dose, oxygen, pH, hydrogen peroxide, added ions and dye classes are also reviewed and summarized. Lastly, pilot plant application of radiation for wastewater treatment is briefly discussed.

Wetland use and resource degradation among small-scale farmers ...

African Journals Online (AJOL)

economic life of smallholders in Cross River State, and the relationship between socio-economic factors and wetland degradation. A multi-stage sampling procedure was used in selecting respondents for the study. Data for this study was analyzed ...

Increased radiation degradation in methyl methacrylate copolymers

International Nuclear Information System (INIS)

Helbert, J.N; Wagner, G.E.; Caplan, P.J.; Poindexter, E.H.

1975-01-01

The effect of polar substituents at the quaternary carbon on degradation processes in several polymers and 10 to 20 percent copolymers of methyl methacrylate was explored. EPR was used to monitor radiation degradation products and to determine radiation G values. Irradiations were carried out at 77 0 K in a gamma irradiator at a dose rate of 0.3 Mrad/hr. (U.S.)

The effect of acquiring life skills through humor on social adjustment rate of the female students.

Science.gov (United States)

Maghsoudi, Jahangir; Sabour, Nazanin Hashemi; Yazdani, Mohsen; Mehrabi, Tayebeh

2010-01-01

Life skills have different effects on various aspects of the mental health. Social adjustment prepares adolescents for entering to the adulthood. On the other hand, humor and joking in the education is considered as a stress reducer and learning increaser. Therefore, the present study conducted aimed to determine the effect of acquiring life skills through humor on the social adjustment rate of the high school girls. This was a two-group semi-experimental study including three phases. The study population included 69 first year high school female students of Isfahan Department of Education district 3 who were selected in simple random sampling. First of all, the social adjustment rate was measured using California Personality Inventory. Thereafter, life skills education was conducted using humor during five sessions. Finally, a test was taken in order to assess the acquisition of the life skills in which passing score was required for re-completing the questionnaire. The data were analyzed using software SPSS(10) and independent and paired t-tests. The findings of the study indicated that the mean score of the social adjustment statistically had a significant difference in the intervention group before and after the intervention. Furthermore, statistically, there was a significant difference between mean score of the social adjustment in the control group and test group after conducting the intervention. The findings of the study indicated that life skills education has been increased through humor on the social adjustment rate of the high school girl students. Considering the efficacy of learning life skills on the social adjustment and results of the other studies which were in accordance with the present study, implementing such trainings with a new method comprehensively is recommended in the schools.

Time profile of abamectin and doramectin excretion and degradation in sheep faeces

Energy Technology Data Exchange (ETDEWEB)

Kolar, Lucija [Institute of Physiology, Pharmacology and Toxicology, Veterinary Faculty, University of Ljubljana, Gerbiceva 60, SI-1000 Ljubljana (Slovenia)]. E-mail: lucija.kolar@vf.uni-lj.si; Flajs, Vesna Cerkvenik [Institute of Food Hygiene and Bromatology, Veterinary Faculty, University of Ljubljana, Gerbiceva 60, SI-1000 Ljubljana (Slovenia)]. E-mail: vesna.cerkvenik@vf.uni-lj.si; Kuzner, Jernej [Institute of Physiology, Pharmacology and Toxicology, Veterinary Faculty, University of Ljubljana, Gerbiceva 60, SI-1000 Ljubljana (Slovenia)]. E-mail: jernej.kuzner@vf.uni-lj.si; Marc, Irena [Centre for Sustainable Recultivation at Vremscica, Veterinary Faculty, University of Ljubljana, Gerbiceva 60, SI-1000 Ljubljana (Slovenia)]. E-mail: irena.marc@vf.uni-lj.si; Pogacnik, Milan [Institute of Pathology, Forensic and Administrative Veterinary Medicine, Veterinary Faculty, University of Ljubljana, Gerbiceva 60, SI-1000 Ljubljana (Slovenia)]. E-mail: milan.pogacnik@vf.uni-lj.si; Bidovec, Andrej [Institute of Breeding and Health Care of Wild Animals, Fishes and Bees, Veterinary Faculty, University of Ljubljana, Gerbiceva 60, SI-1000 Ljubljana (Slovenia)]. E-mail: andrej.bidovec@vf.uni-lj.si; Gestel, Cornelis A.M. van [Institute of Ecological Science, Vrije Universiteit, De Boelelaan 1085, 1081 HV Amsterdam (Netherlands)]. E-mail: kees.van.gestel@ecology.falw.vu.nl; Erzen, Nevenka Kozuh [Institute of Physiology, Pharmacology and Toxicology, Veterinary Faculty, University of Ljubljana, Gerbiceva 60, SI-1000 Ljubljana (Slovenia)]. E-mail: nevenka.kozuh@vf.uni-lj.si

2006-11-15

We studied abamectin and doramectin excretion and their degradation in sheep faeces under field conditions on pasture after a single subcutaneous dose (0.2 mg/kg body weight). In the excretion experiment, maximal abamectin concentration (1277 ng/g dry faeces) was detected on day 3, while doramectin concentration showed two peaks (2186 and 1780 ng/g dry faeces on days 2 and 5, respectively). Both avermectins were excreted at approximately the same rate (k = 0.23 day{sup -1} for abamectin and 0.19 day{sup -1} for doramectin). In the field, a rapid loss of abamectin and doramectin from sheep faeces was seen during the first 32 days after which concentrations remained constant at approximately 77 ng/g and 300 ng/g, respectively. The half life values (DT{sub 5}) for abamectin and doramectin dissipation from sheep faeces were 23 and 22 days, respectively, during the first 32 days. Dissipation of both avermectins was strongly correlated with moisture content of the faeces. - Abamectin and doramectin show similar excretion and degradation behaviour in sheep faeces.

Degradation of PPCPs in activated sludge from different WWTPs in Denmark

DEFF Research Database (Denmark)

Chen, Xijuan; Vollertsen, Jes; Nielsen, Jeppe Lund

2015-01-01

was performed to assess the removal of frequently occurring pharmaceuticals (Naproxen, Fenoprofen, Ketoprofen, Dichlofenac, Carbamazepine) and the biocide Triclosan in activated sludge from four different Danish WWTPs. The respective degradation constants were compared to operational parameters previous shown...... to be of importance for degradation of micropollutants such as biomass concentration, and sludge retention time (SRT). The most rapid degradation, was observed for NSAID pharmaceuticals (55–90 % for Fenoprofen, 77–94 % for Ketoprofen and 46–90 % for Naproxen), followed by Triclosan (61–91 %), while Dichlofenac...... and Carbamazepine were found to be persistent in the systems. Degradation rate constants were calculated as 0.0026–0.0407 for NSAID pharmaceuticals and 0.0022–0.0065 for triclosan. No relationships were observed between degradation rates and biomass concentrations in the diverse sludges. However...

Hydrocarbon degradation, plant colonization and gene expression of alkane degradation genes by endophytic Enterobacter ludwigii strains

International Nuclear Information System (INIS)

Yousaf, Sohail; Afzal, Muhammad; Reichenauer, Thomas G.; Brady, Carrie L.; Sessitsch, Angela

2011-01-01

The genus Enterobacter comprises a range of beneficial plant-associated bacteria showing plant growth promotion. Enterobacter ludwigii belongs to the Enterobacter cloacae complex and has been reported to include human pathogens but also plant-associated strains with plant beneficial capacities. To assess the role of Enterobacter endophytes in hydrocarbon degradation, plant colonization, abundance and expression of CYP153 genes in different plant compartments, three plant species (Italian ryegrass, birdsfoot trefoil and alfalfa) were grown in sterile soil spiked with 1% diesel and inoculated with three endophytic E. ludwigii strains. Results showed that all strains were capable of hydrocarbon degradation and efficiently colonized the rhizosphere and plant interior. Two strains, ISI10-3 and BRI10-9, showed highest degradation rates of diesel fuel up to 68% and performed best in combination with Italian ryegrass and alfalfa. All strains expressed the CYP153 gene in all plant compartments, indicating an active role in degradation of diesel in association with plants. - Highlights: → E. ludwigii strains efficiently colonized plants in a non-sterile soil environment. → E. ludwigii strains efficiently expressed alkane degradation genes in plants. → E. ludwigii efficiently degraded alkane contaminations and promoted plant growth. → E. ludwigii interacted more effectively with Italian ryegrass than with other plants. → Degradation activity varied with plant and microbial genotype as well as with time. - Enterobacter ludwigii strains belonging to the E. cloacae complex are able to efficiently degrade alkanes when associated with plants and to promote plant growth.

Hydrocarbon degradation, plant colonization and gene expression of alkane degradation genes by endophytic Enterobacter ludwigii strains

Energy Technology Data Exchange (ETDEWEB)

Yousaf, Sohail [AIT Austrian Institute of Technology GmbH, Bioresources Unit, A-2444 Seibersdorf (Austria); Afzal, Muhammad [AIT Austrian Institute of Technology GmbH, Bioresources Unit, A-2444 Seibersdorf (Austria); National Institute for Biotechnology and Genetic Engineering (NIBGE), Faisalabad (Pakistan); Reichenauer, Thomas G. [AIT Austrian Institute of Technology GmbH, Environmental Resources and Technologies Unit, A-2444 Seibersdorf (Austria); Brady, Carrie L. [Forestry and Agricultural Biotechnology Institute, Department of Microbiology and Plant Pathology, University of Pretoria, Pretoria (South Africa); Sessitsch, Angela, E-mail: angela.sessitsch@ait.ac.at [AIT Austrian Institute of Technology GmbH, Bioresources Unit, A-2444 Seibersdorf (Austria)

2011-10-15

The genus Enterobacter comprises a range of beneficial plant-associated bacteria showing plant growth promotion. Enterobacter ludwigii belongs to the Enterobacter cloacae complex and has been reported to include human pathogens but also plant-associated strains with plant beneficial capacities. To assess the role of Enterobacter endophytes in hydrocarbon degradation, plant colonization, abundance and expression of CYP153 genes in different plant compartments, three plant species (Italian ryegrass, birdsfoot trefoil and alfalfa) were grown in sterile soil spiked with 1% diesel and inoculated with three endophytic E. ludwigii strains. Results showed that all strains were capable of hydrocarbon degradation and efficiently colonized the rhizosphere and plant interior. Two strains, ISI10-3 and BRI10-9, showed highest degradation rates of diesel fuel up to 68% and performed best in combination with Italian ryegrass and alfalfa. All strains expressed the CYP153 gene in all plant compartments, indicating an active role in degradation of diesel in association with plants. - Highlights: > E. ludwigii strains efficiently colonized plants in a non-sterile soil environment. > E. ludwigii strains efficiently expressed alkane degradation genes in plants. > E. ludwigii efficiently degraded alkane contaminations and promoted plant growth. > E. ludwigii interacted more effectively with Italian ryegrass than with other plants. > Degradation activity varied with plant and microbial genotype as well as with time. - Enterobacter ludwigii strains belonging to the E. cloacae complex are able to efficiently degrade alkanes when associated with plants and to promote plant growth.

Quantifying the degradation of organic matter in marine sediments: A review and synthesis

Science.gov (United States)

Arndt, Sandra; Jørgensen, B. B.; LaRowe, D. E.; Middelburg, J. J.; Pancost, R. D.; Regnier, P.

2013-08-01

Quantifying the rates of biogeochemical processes in marine sediments is essential for understanding global element cycles and climate change. Because organic matter degradation is the engine behind benthic dynamics, deciphering the impact that various forces have on this process is central to determining the evolution of the Earth system. Therefore, recent developments in the quantitative modeling of organic matter degradation in marine sediments are critically reviewed. The first part of the review synthesizes the main chemical, biological and physical factors that control organic matter degradation in sediments while the second part provides a general review of the mathematical formulations used to model these processes and the third part evaluates their application over different spatial and temporal scales. Key transport mechanisms in sedimentary environments are summarized and the mathematical formulation of the organic matter degradation rate law is described in detail. The roles of enzyme kinetics, bioenergetics, temperature and biomass growth in particular are highlighted. Alternative model approaches that quantify the degradation rate constant are also critically compared. In the third part of the review, the capability of different model approaches to extrapolate organic matter degradation rates over a broad range of temporal and spatial scales is assessed. In addition, the structure, functions and parameterization of more than 250 published models of organic matter degradation in marine sediments are analyzed. The large range of published model parameters illustrates the complex nature of organic matter dynamics, and, thus, the limited transferability of these parameters from one site to another. Compiled model parameters do not reveal a statistically significant correlation with single environmental characteristics such as water depth, deposition rate or organic matter flux. The lack of a generic framework that allows for model parameters to be

Dose rate effect on material aging due to radiation. [Gamma radiation

Energy Technology Data Exchange (ETDEWEB)

Okamoto, Shin-ichi (Radiation Center of Osaka Prefecture, Sakai (Japan)); Hayakawa, Chikara; Takeya, Chikashi

1982-12-01

Although many reports have been presented on the radiation aging of the organic materials for electric cables, those have been based on the experiments carried out at high dose rate near 1 x 10/sup 6/ rad/h, assuming that aging effect depends on only radiation dose. Therefore, to investigate the aging behaviour in low dose rate range is an important subject to predict their practical life time. In this report, the results of having investigated the aging behaviour of six types of materials are described, (polyethylene for general insulation purpose, chemically cross-linked polyethylene, fire-retardant chemically cross-linked polyethylene, fire-retardant ethylene-propylene rubber, fire-retardant chloro-sulfonated polyethylene for sheaths, and fire-retardant, low hydrochloric acid, special heat-resistant vinyl for insulation purpose or chloroclean). They were irradiated with /sup 60/Co ..gamma..-ray at the dose from 5 x 10/sup 3/ to 1 x 10/sup 6/ rad/h, and their deterioration was tested for the items of elongation, tensile strength, resistivity, dielectric tangent and gel fraction. The aging mechanism and dose rate effect were also considered. The dose rate effect appeared or did not appear depending on the types of materials and also their properties. The materials that showed the dose rate effect included the typical ones whose characteristics degraded with the decreasing dose rate, and the peculiar ones whose deterioration of characteristics did not appear constantly. Aging mechanism may vary in the case of high dose rate and low dose rate. Also, if the life time at respective dose rate in relatively higher dose rate region is clarified, the life time in low dose rate region may possibly be predicted.

Radiation damage and life-time evaluation of RBMK graphite stack

Energy Technology Data Exchange (ETDEWEB)

Platonov, P A; Chugunov, O K; Manevsky, V N; Karpukhin, V I [Russian Research Centre Kurchatov Inst., Moscow (Russian Federation). Reactor Material Div.

1996-08-01

At the present time there are 11 NPP units with RBMK reactors in operation in Russia, with the oldest now in operation 22 years. Design life-time of the RBMK-1000 reactor is 30 years. This paper addresses the evaluation of RBMK graphite stack life-time. It is the practice in Russia to evaluate the reliability of the channel reactor graphite stack using at least three criteria: degradation of physical-mechanical properties of graphite, preservation of the graphite brick integrity, and degradation of the graphite stack as a structure. Stack life-time evaluation by different criteria indicates that the most realistic approach may be realized on the basis of the criteria of brick cracking and degradation of the graphite stack as a structure. The RBMK reactor graphite stack life-time depends on its temperature and for different units it may be different. (author). 2 refs, 10 figs.

Evaluation of the performance degradation at PAFC investigation of dealloying process of electrocatalysts with in-situ XRD

Energy Technology Data Exchange (ETDEWEB)

Nakajima, Noriyuki; Uchida, Hiroyuki; Watanabe, Masahiro [Yamanashi Univ., Kofu (Japan)] [and others

1996-12-31

As a complementary research project to the demonstration project of 5MW and 1 MW PAFC plants, the mechanism and rate of deterioration of the cells and stacks have been studied from 1995 FY, with the objective of establishing an estimation method for the service life-time of the cell stacks. This work has been performed in the Basic Research Project, as part of that project on PAFC`s, selecting four subjects (Electrocatalysts degradation, Electrolyte fill-level, Cell material corrosion, Electrolyte loss) as the essential factors relating to the life-time. In this study, the effect of temperature and potential on the dealloying process of electrocatalysts was examined in H{sub 3}PO{sub 4} electrolyte with X-ray diffraction measurement.

Evaluation of temperature-enhanced gain degradation of verticle npn and lateral pnp bipolar transistors

International Nuclear Information System (INIS)

Witczak, S.C.; Lacoe, R.C.; Galloway, K.F.

1997-01-01

The effect of dose rate on radiation-induced gain degradation is compared for verticle npn and lateral pnp bipolar transistors. High dose rate irradiations at elevated temperatures are more effective at simulating low dose rate degradation in the lateral pnp transistors

DSNF AND OTHER WASTE FORM DEGRADATION ABSTRACTION

International Nuclear Information System (INIS)

Thornton, T.A.

2000-01-01

The purpose of this analysis/model report (AMR) is to select and/or abstract conservative degradation models for DOE-(US. Department of Energy) owned spent nuclear fuel (DSNF) and the immobilized ceramic plutonium (Pu) disposition waste forms for application in the proposed monitored geologic repository (MGR) postclosure Total System Performance Assessment (TSPA). Application of the degradation models abstracted herein for purposes other than TSPA should take into consideration the fact that they are, in general, very conservative. Using these models, the forward reaction rate for the mobilization of radionuclides, as solutes or colloids, away from the waste fondwater interface by contact with repository groundwater can then be calculated. This forward reaction rate generally consists of the dissolution reaction at the surface of spent nuclear fuel (SNF) in contact with water, but the degradation models, in some cases, may also include and account for the physical disintegration of the SNF matrix. The models do not, however, account for retardation, precipitation, or inhibition of the migration of the mobilized radionuclides in the engineered barrier system (EBS). These models are based on the assumption that all components of the DSNF waste form are released congruently with the degradation of the matrix

DSNF and other waste form degradation abstraction

Energy Technology Data Exchange (ETDEWEB)

Thornton, Thomas A.

2000-12-20

The purpose of this analysis/model report (AMR) is to select and/or abstract conservative degradation models for DOE-(US. Department of Energy) owned spent nuclear fuel (DSNF) and the immobilized ceramic plutonium (Pu) disposition waste forms for application in the proposed monitored geologic repository (MGR) postclosure Total System Performance Assessment (TSPA). Application of the degradation models abstracted herein for purposes other than TSPA should take into consideration the fact that they are, in general, very conservative. Using these models, the forward reaction rate for the mobilization of radionuclides, as solutes or colloids, away from the waste fondwater interface by contact with repository groundwater can then be calculated. This forward reaction rate generally consists of the dissolution reaction at the surface of spent nuclear fuel (SNF) in contact with water, but the degradation models, in some cases, may also include and account for the physical disintegration of the SNF matrix. The models do not, however, account for retardation, precipitation, or inhibition of the migration of the mobilized radionuclides in the engineered barrier system (EBS). These models are based on the assumption that all components of the DSNF waste form are released congruently with the degradation of the matrix.

Individual condition, standard metabolic rate, and rearing temperature influence steelhead and rainbow trout (Oncorhynchus mykiss) life histories

Science.gov (United States)

Matthew R. Sloat; Gordon H. Reeves

2014-01-01

We reared juvenile Oncorhychus mykiss with low and high standard metabolic rates (SMR) under alternative thermal regimes to determine how these proximate factors influence life histories in a partially migratory salmonid fish. High SMR significantly decreased rates of freshwater maturation and increased rates of smoltification in females, but not...

Rate of hydrolysis and degradation of the cyanogenic glycoside - dhurrin - in soil

DEFF Research Database (Denmark)

Johansen, Henrik; Damgaard, Lars Holm; Olsen, Carl Erik

2007-01-01

Cyanogenic glycosides are common plant toxins. Toxic hydrogen cyanide originating from cyanogenic glycosides may affect soil processes and water quality. In this study, hydrolysis, degradation and sorption of dhurrin (4-hydroxymandelonitrile-b-D-glucoside) produced by sorghum has been studied...

The influence of cycling temperature and cycling rate on the phase specific degradation of a positive electrode in lithium ion batteries: A post mortem analysis

Science.gov (United States)

Darma, Mariyam Susana Dewi; Lang, Michael; Kleiner, Karin; Mereacre, Liuda; Liebau, Verena; Fauth, Francois; Bergfeldt, Thomas; Ehrenberg, Helmut

2016-09-01

The influence of cycling temperatures and cycling rates on the cycling stability of the positive electrode (cathode) of commercial batteries are investigated. The cathode is a mixture of LiMn2O4 (LMO), LiNi0.5Co0.2Mn0.3O2 (NCM) and LiNi0.8Co0.15Al0.05O2 (NCA). It is found that increasing the cycling temperature from 25 °C to 40 °C is detrimental to the long term cycling stability of the cathode. Contrastingly, the improved cycling stability is observed for the cathodes cycled at higher charge/discharge rate (2C/3C instead of 1C/2C). The microstructure analysis by X-ray powder diffraction reveals that a significant capacity fading and an increased overvoltage is observed for NCM and NCA in all the fatigued cathodes. After high number of cycling (above 1500 cycles), NCM becomes partially inactive. In contrast to NCM and NCA, LMO shows a good cycling stability at 25 °C. A pronounced degradation of LMO is only observed for the fatigued cathodes cycled at 40 °C. The huge capacity losses of NCM and NCA are most likely because the blended cathodes were cycled up to 4.12 V vs. the graphite anode during the cycle-life test (corresponds to 4.16 V vs. Li+/Li); which is beyond the stability limit of the layered oxides below 4.05 V vs. Li+/Li.

Impact of life expectancy, literacy rate, opened unemployment rate and gross domestic regional income per capita on poverty in the districts/city in Central Sulawesi Province

Science.gov (United States)

Tombolotutu, A. D.; Djirimu, M. A.; Lutfi, M.; Anggadini, F.

2018-05-01

Research was conducted in several districts/city in Central Sulawesi Province in order to determine the effect of life expectancy, literacy rate, opened unemployment rate, and gross domestic regional income per capita on poverty at the districts/city in the province. The analysis used is Panel Data Regression. The results show that first, life expectancy and gross domestic regional income have a negative and significant impact on the poverty level in the districts/city in the Province. Second, the opened unemployment rate has a positive and significant effect on the poverty level in the districts/city in the province. Third, literacy rates show a positive effect and insignificant effect on the poverty level in the districts/city in the Province of Central Sulawesi. Fourth, these four variables simultaneously affect the poverty in the districts/city in Central Sulawesi

Influence of dihydroxybenzenes on paracetamol and ciprofloxacin degradation and iron(III) reduction in Fenton processes.

Science.gov (United States)

Costa E Silva, Beatriz; de Lima Perini, João Angelo; Nogueira, Raquel F Pupo

2017-03-01

The degradation of paracetamol (PCT) and ciprofloxacin (CIP) was compared in relation to the generation of dihydroxylated products, Fe(III) reduction and reaction rate in the presence of dihydroxybenzene (DHB) compounds, or under irradiation with free iron (Fe 3+ ) or citrate complex (Fecit) in Fenton or photo-Fenton process. The formation of hydroquinone (HQ) was observed only during PCT degradation in the dark, which increased drastically the rate of PCT degradation, since HQ formed was able to reduce Fe 3+ and contributed to PCT degradation efficiency. When HQ was initially added, PCT and CIP degradation rate in the dark was much higher in comparison to the absence of HQ, due to the higher and faster formation of Fe 2+ at the beginning of reaction. In the absence of HQ, no CIP degradation was observed; however, when HQ was added after 30 min, the degradation rate increased drastically. Ten PCT hydroxylated intermediates were identified in the absence of HQ, which could contribute for Fe(III) reduction and consequently to the degradation in a similar way as HQ. During CIP degradation, only one product of hydroxyl radical attack on benzene ring and substitution of the fluorine atom was identified when HQ was added to the reaction medium.

Advanced Oxidation Degradation of Diclofenac

Energy Technology Data Exchange (ETDEWEB)

Cooper, William J., E-mail: wcooper@uci.edu [Urban Water Research Center, Department of Civil and Environmental Engineering, University of California, Irvine, CA 92697 (United States); Song Weihua, E-mail: wsong@fudan.edu.cn [Department of Environmental Science & Engineering, Fudan University, Shanghai 200433 (China)

2012-07-01

Advanced oxidation/reduction processes (AO/RPs), utilize free radical reactions to directly degrade chemical contaminants as an alternative to traditional water treatment. This study reports the absolute rate constants for reaction of diclofenac sodium and the model compound (2, 6-dichloraniline) with the two major AO/RP radicals; the hydroxyl radical (•OH) and hydrated electron (e{sup -}{sub aq}). The bimolecular reaction rate constants (M{sup -1} s{sup -1}) for diclofenac for •OH was (9.29 ± 0.11) x 10{sup 9}, and, for e- aq was (1.53 ± 0.03) x10{sup 9}. Preliminary degradation mechanisms are suggested based on product analysis using {sup 60}Co γ-irradiation and LC-MS for reaction by-product identification. The toxicity of products was evaluated using the Vibrio fischeri luminescent bacteria method. (author)

Personality, self-rated health, and subjective age in a life-span sample: the moderating role of chronological age.

Science.gov (United States)

Stephan, Yannick; Demulier, Virginie; Terracciano, Antonio

2012-12-01

The present study tested whether chronological age moderates the association between subjective age and self-rated health and personality in a community-dwelling life-span sample (N = 1,016; age range: 18-91 years). Self-rated health, extraversion, and openness to experience were associated with a younger subjective age at older ages. Conscientious individuals felt more mature early in life. Conscientiousness, neuroticism, and agreeableness were not related to subjective age at older ages. These findings suggest that with aging self-rated health and personality traits are increasingly important for subjective age. 2013 APA, all rights reserved

Repeated batch and continuous degradation of chlorpyrifos by Pseudomonas putida.

Science.gov (United States)

Pradeep, Vijayalakshmi; Subbaiah, Usha Malavalli

2015-01-01

The present study was undertaken with the objective of studying repeated batch and continuous degradation of chlorpyrifos (O,O-diethyl O-3,5,6-trichloropyridin-2-yl phosphorothioate) using Ca-alginate immobilized cells of Pseudomonas putida isolated from an agricultural soil, and to study the genes and enzymes involved in degradation. The study was carried out to reduce the toxicity of chlorpyrifos by degrading it to less toxic metabolites. Long-term stability of pesticide degradation was studied during repeated batch degradation of chlorpyrifos, which was carried out over a period of 50 days. Immobilized cells were able to show 65% degradation of chlorpyrifos at the end of the 50th cycle with a cell leakage of 112 × 10(3) cfu mL(-1). During continuous treatment, 100% degradation was observed at 100 mL h(-1) flow rate with 2% chlorpyrifos, and with 10% concentration of chlorpyrifos 98% and 80% degradation was recorded at 20 mL h(-1) and 100 mL h(-1) flow rate respectively. The products of degradation detected by liquid chromatography-mass spectrometry analysis were 3,5,6-trichloro-2-pyridinol and chlorpyrifos oxon. Plasmid curing experiments with ethidium bromide indicated that genes responsible for the degradation of chlorpyrifos are present on the chromosome and not on the plasmid. The results of Polymerase chain reaction indicate that a ~890-bp product expected for mpd gene was present in Ps. putida. Enzymatic degradation studies indicated that the enzymes involved in the degradation of chlorpyrifos are membrane-bound. The study indicates that immobilized cells of Ps. putida have the potential to be used in bioremediation of water contaminated with chlorpyrifos.

Enhanced mitochondrial degradation of yeast cytochrome c with amphipathic structures.

Science.gov (United States)

Chen, Xi; Moerschell, Richard P; Pearce, David A; Ramanan, Durga D; Sherman, Fred

2005-02-01

The dispensable N-terminus of iso-1-cytochrome c (iso-1) in the yeast Saccharomyces cerevisiae was replaced by 11 different amphipathic structures. Rapid degradation of the corresponding iso-1 occurred, with the degree of degradation increasing with the amphipathic moments; and this amphipathic-dependent degradation was designated ADD. ADD occurred with the holo-forms in the mitochondria but not as the apo-forms in the cytosol. The extreme mutant type degraded with a half-life of approximately 12 min, whereas the normal iso-1 was stable over hours. ADD was influenced by the rho+/rho- state and by numerous chromosomal genes. Most importantly, ADD appeared to be specifically suppressed to various extents by deletions of any of the YME1, AFG3, or RCA1 genes encoding membrane-associated mitochondrial proteases, probably because the amphipathic structures caused a stronger association with the mitochondrial inner membrane and its associated proteases. The use of ADD assisted in the differentiation of substrates of different mitochondrial degradation pathways.

Structural insight into molecular mechanism of poly(ethylene terephthalate) degradation.

Science.gov (United States)

Joo, Seongjoon; Cho, In Jin; Seo, Hogyun; Son, Hyeoncheol Francis; Sagong, Hye-Young; Shin, Tae Joo; Choi, So Young; Lee, Sang Yup; Kim, Kyung-Jin

2018-01-26

Plastics, including poly(ethylene terephthalate) (PET), possess many desirable characteristics and thus are widely used in daily life. However, non-biodegradability, once thought to be an advantage offered by plastics, is causing major environmental problem. Recently, a PET-degrading bacterium, Ideonella sakaiensis, was identified and suggested for possible use in degradation and/or recycling of PET. However, the molecular mechanism of PET degradation is not known. Here we report the crystal structure of I. sakaiensis PETase (IsPETase) at 1.5 Å resolution. IsPETase has a Ser-His-Asp catalytic triad at its active site and contains an optimal substrate binding site to accommodate four monohydroxyethyl terephthalate (MHET) moieties of PET. Based on structural and site-directed mutagenesis experiments, the detailed process of PET degradation into MHET, terephthalic acid, and ethylene glycol is suggested. Moreover, other PETase candidates potentially having high PET-degrading activities are suggested based on phylogenetic tree analysis of 69 PETase-like proteins.

Age-related degradation of boiling water reactor vessel internals

International Nuclear Information System (INIS)

Ware, A.G.; Shah, V.N.

1992-01-01

Researchers at the Idaho National Engineering Laboratory performed an assessment of the aging of the reactor internals in boiling water reactors (BWRs), and identified the unresolved technical issues related to the degradation of these components. The overall life-limiting mechanism is intergranular stress corrosion cracking (IGSCC). Irradiation-assisted stress corrosion cracking, fatigue, and thermal aging embrittlement are other potential degradation mechanisms. Several failures in BWR internals have been caused by a combination of factors such as environment, high residual or preload stresses, and flow-induced vibration. The ASME Code Section XI in-service inspection requirements are insufficient for detecting aging-related degradation at many locations in reactor internals. Many of the potential locations for IGSCC or fatigue are not accessible for inspection. (orig.)

Academic Performance and Pass Rates: Comparison of Three First-Year Life Science Courses

Science.gov (United States)

Downs, C. T.

2009-01-01

First year students' academic performance in three Life Science courses (Botany, Zoology and Bioscience) was compared. Pass rates, as well as the means and distributions of final marks were analysed. Of the three components (coursework, practical and theory examinations) contributing to the final mark of each course, students performed best in the…

Strong Impact on the Polycyclic Aromatic Hydrocarbon (PAH)-Degrading Community of a PAH-Polluted Soil but Marginal Effect on PAH Degradation when Priming with Bioremediated Soil Dominated by Mycobacteria

DEFF Research Database (Denmark)

Johnsen, Anders R.; Schmidt, Stine; Hybholdt, Trine K.

2007-01-01

Bioaugmentation of soil polluted with polycyclic aromatic hydrocarbons (PAHs) is often disappointing because of the low survival rate and low activity of the introduced degrader bacteria. We therefore investigated the possibility of priming PAH degradation in soil by adding 2% of bioremediated soil...... with a high capacity for PAH degradation. The culturable PAH-degrading community of the bioremediated primer soil was dominated by Mycobacterium spp. A microcosm containing pristine soil artificially polluted with PAHs and primed with bioremediated soil showed a fast, 100- to 1,000-fold increase in numbers...... of culturable phenanthrene-, pyrene-, and fluoranthene degraders and a 160-fold increase in copy numbers of the mycobacterial PAH dioxygenase gene pdo1. A nonpolluted microcosm primed with bioremediated soil showed a high rate of survival of the introduced degrader community during the 112 days of incubation...

Protein synthesis and degradation during starvation-induced cardiac atrophy in rabbits

International Nuclear Information System (INIS)

Samarel, A.M.; Parmacek, M.S.; Magid, N.M.; Decker, R.S.; Lesch, M.

1987-01-01

To determine the relative importance of protein degradation in the development of starvation-induced cardiac atrophy, in vivo fractional synthetic rates of total cardiac protein, myosin heavy chain, actin, light chain 1, and light chain 2 were measured in fed and fasted rabbits by continuous infusion of [ 3 H] leucine. In addition, the rate of left ventricular protein accumulation and loss were assessed in weight-matched control and fasted rabbits. Rates of total cardiac protein degradation were then estimated as the difference between rates of synthesis and growth. Fasting produced left ventricular atrophy by decreasing the rate of left ventricular protein synthesis (34.8 +/- 1.4, 27.3 +/- 3.0, and 19.3 +/- 1.2 mg/day of left ventricular protein synthesized for 0-, 3-, and 7-day fasted rabbits, respectively). Inhibition of contractile protein synthesis was evident by significant reductions in the fractional synthetic rates of all myofibrillar protein subunits. Although fractional rates of protein degradation increased significantly within 7 days of fasting, actual amounts of left ventricular protein degraded per day were unaffected. Thus, prolonged fasting profoundly inhibits the synthesis of new cardiac protein, including the major protein constituents of the myofibril. Both this inhibition in new protein synthesis as well as a smaller but significant reduction in the average half-lives of cardiac proteins are responsible for atrophy of the heart in response to fasting

Study on the degradation of chitosan slurries

Directory of Open Access Journals (Sweden)

Benjamin Martini

2016-01-01

Full Text Available In the present work, we measured the degradation rate of different chitosan slurries. Several parameters were monitored such as temperature (25 °C, 37 °C, 50 °C; chitosan concentration (1% and 2% (w/V; and polymer molecular weight. The samples were tested in dynamic sweep test mode. This test is able to provide a reliable estimation of viscosity variations of the slurries; in turn, these variations could be related to degradation rate of the system in the considered conditions. The resulting information is particularly important especially in applications in which there is a close relationship between physical properties and molecular structure.

Degradation kinetics of monoethanolamine during CO2 and H2 S absorption from biogas

Directory of Open Access Journals (Sweden)

Preecha Kasikamphaiboon

2015-02-01

Full Text Available The rate of degradation of MEA during CO2 and H2 S absorption in the biogas upgrading process was examined in four degradation systems, i.e., MEA-CO2 , MEA-CO2 -O2 , MEA-CO2 -H2 S and MEA-CO2 -O2 -H2 S. Degradation experiments were performed in a 800-ml stainless steel autoclave reactor, using MEA concentrations of 3 and 5 mol/L, CO2 loadings of 0.4 and 0.5 mol CO2 /mol MEA, O2 pressure of 200 kPa, and H2 S concentrations of 84 and 87 mg/L at temperatures of 120 and 140C. The results showed that, for the MEA-CO2 system, an increase in temperature or MEA concentration resulted in a higher rate of MEA degradation. In contrast, an increase in CO2 loading in the MEA-CO2 -O2 system led to a reduction of MEA degradation. The degradation rate of the system with O2 was with 8.3 times as high as that of the system without O2 . The presence of H2 S did not appear to affect the rate of degradation in the MEA-CO2 -H2 S system. However, for the system in which both H2 S and O2 were present, the MEA degradation was additionally induced by H2 S, thus, resulting in higher degradation rates than those of the system with O2 only. The extent of degradation under the same period of time increased in the order MEA-CO2 , MEA-CO2 -H2 S < MEA-CO2 -O2 < MEA-CO2 -O2 -H2 S.

Pattern-recognition system application to EBR-II plant-life extension

International Nuclear Information System (INIS)

King, R.W.; Radtke, W.H.; Mott, J.E.

1988-01-01

A computer-based pattern-recognition system, the System State Analyzer (SSA), is being used as part of the EBR-II plant-life extension program for detection of degradation and other abnormalities in plant systems. The SSA is used for surveillance of the EBR-II primary system instrumentation, primary sodium pumps, and plant heat balances. Early results of this surveillance indicate that the SSA can detect instrumentation degradation and system performance degradation over varying time intervals, and can provide derived signal values to replace signals from failed critical sensors. These results are being used in planning for extended-life operation of EBR-II

Potential impact of methyl isobutyl ketone (MIBK) on phenols degradation in an UASB reactor and its degradation properties.

Science.gov (United States)

Wang, Wei; Yang, Kai; Sierra, Julian Muñoz; Zhang, Xuedong; Yuan, Shoujun; Hu, Zhenhu

2017-07-05

Methyl isobutyl ketone (MIBK) as a solvent is extensively used for the phenols extraction from the wastewater, so it is unavoidable to expose in the effluent due to the solubility and leakage problem. The present study evaluated the impact of MIBK on phenols degradation in an UASB reactor and analyzed its degradation properties. The results indicated that the continuous dosing (0.1gL -1 ) and impact (10gL -1 ) of MIBK had limited effect on phenols removal (1-2% reduction) in the UASB reactor, but the specific methanogenic activity (SMA) values of sludge decreased by 45-75% after MIBK exposure. Anaerobic degradation rate of MIBK fitted well to a pseudo-first-order kinetic equation with respect to the initial concentration of 35mgL -1 (k=0.0115h -1 , R 2 =0.9664). Furthermore, the relative methane generation rate constants of MIBK were 0.00816, 0.00613, 0.00273, and 0.00207d -1 at the initial concentrations of 0.1, 0.5, 5, and 10gL -1 , respectively. MIBK showed higher inhibitory effect on the methanogenesis than on phenols degradation. This study pointed out that the industrial installations should consider the influence of solvent on anaerobic treatment of phenolic wastewater. Copyright © 2017 Elsevier B.V. All rights reserved.

In Vivo Biological Evaluation of High Molecular Weight Multifunctional Acid-Degradable Polymeric Drug Carriers with Structurally Different Ketals.

Science.gov (United States)

Shenoi, Rajesh A; Abbina, Srinivas; Kizhakkedathu, Jayachandran N

2016-11-14

Understanding the influence of degradable chemical moieties on in vivo degradation, tissue distribution, and excretion is critical for the design of novel biodegradable drug carriers. Polyketals have recently emerged as a promising therapeutic delivery platform due to their ability to degrade under mild acidic intracellular compartments and generation of nontoxic degradation products. However, the effect of chemical structure of the ketal groups on the in vivo degradation, biodistribution, and pharmacokinetics of water-soluble ketal-containing polymers has not been explored. In the present work, we synthesized high molecular weight, water-soluble biodegradable hyperbranched polyglycerols (BHPGs) through the incorporation of structurally different ketal groups into the main chain of highly biocompatible polyglycerols. BHPGs showed pH and ketal group structure dependent degradation in buffer solutions. When the polymers were intravenously administered in mice, a strong dependence of in vivo degradation, biodistribution, and clearance on the ketal group structure was observed. All the BHPGs demonstrated degradation and clearance in vivo, with minimal tissue accumulation. Interestingly, an unanticipated degradation behavior of BHPGs with structurally different ketal groups was observed in vivo in comparison to their degradation in buffer solutions. BHPGs with cyclohexyl ketal (CHK) and cyclopentyl ketal (CPK) groups degraded much faster and were cleared from circulation much rapidly, while BHPG with glycerol hydroxy butanone ketal (GHBK) group degraded at a much slower rate and exhibited similar plasma half-life as that of nondegradable HPG. BHPG-GHBK also showed significantly lower tissue accumulation than nondegradable HPG after 30 days of administration. The difference in in vivo degradation may be attributed to the difference in hydrophobic characteristics of different ketal containing polymers, which may change their interaction with proteins and cells in vivo

Integration of balance and strength training into daily life activity to reduce rate of falls in older people (the LiFE study): randomised parallel trial.

Science.gov (United States)

Clemson, Lindy; Fiatarone Singh, Maria A; Bundy, Anita; Cumming, Robert G; Manollaras, Kate; O'Loughlin, Patricia; Black, Deborah

2012-08-07

To determine whether a lifestyle integrated approach to balance and strength training is effective in reducing the rate of falls in older, high risk people living at home. Three arm, randomised parallel trial; assessments at baseline and after six and 12 months. Randomisation done by computer generated random blocks, stratified by sex and fall history and concealed by an independent secure website. Residents in metropolitan Sydney, Australia. Participants aged 70 years or older who had two or more falls or one injurious fall in past 12 months, recruited from Veteran's Affairs databases and general practice databases. Exclusion criteria were moderate to severe cognitive problems, inability to ambulate independently, neurological conditions that severely influenced gait and mobility, resident in a nursing home or hostel, or any unstable or terminal illness that would affect ability to do exercises. Three home based interventions: Lifestyle integrated Functional Exercise (LiFE) approach (n=107; taught principles of balance and strength training and integrated selected activities into everyday routines), structured programme (n=105; exercises for balance and lower limb strength, done three times a week), sham control programme (n=105; gentle exercise). LiFE and structured groups received five sessions with two booster visits and two phone calls; controls received three home visits and six phone calls. Assessments made at baseline and after six and 12 months. Primary measure: rate of falls over 12 months, collected by self report. Secondary measures: static and dynamic balance; ankle, knee and hip strength; balance self efficacy; daily living activities; participation; habitual physical activity; quality of life; energy expenditure; body mass index; and fat free mass. After 12 months' follow-up, we recorded 172, 193, and 224 falls in the LiFE, structured exercise, and control groups, respectively. The overall incidence of falls in the LiFE programme was 1.66 per person

Spin Transfer in Polymer Degradation of Abnormal Linkage

Science.gov (United States)

Yu, Tianrong; Tian, Chuanjin; Liu, Xizhe; Wang, Jia; Gao, Yang; Wang, Zhigang

2017-07-01

The degradation of polymer materials plays an important role in production and life. In this work, the degradation mechanism of poly-α-methylstyrene (PAMS) tetramers with abnormal linkage was investigated by using density functional theory (DFT). Calculated results indicate that the head-to-head and the tail-to-tail reactions needed to overcome the energy barriers are about 0.15 eV and about 1.26 eV, respectively. The broken C-C bond at the unsaturated end of the chain leads to the dissociation of alpha-methylstyrene (AMS) monomers one by one. Furthermore, the analyses of bond characteristics are in good agreement with the results of energy barriers. In addition, the spin population analysis presents an interesting net spin transfer process in depolymerization reactions. We hope that the current theoretical results provide useful help to understand the degradation mechanism of polymers.

The impact of neighborhood social capital on life satisfaction and self-rated health: A possible pathway for health promotion?

Science.gov (United States)

Maass, Ruca; Kloeckner, Christian A; Lindstrøm, Bengt; Lillefjell, Monica

2016-11-01

Neighborhood social capital has repeatedly been linked to favorable health-outcomes and life satisfaction. However, it has been questioned whether it's impact on health has been over-rated. We aim to investigate relationships between neighborhood social capital and self-rated health (SRH) and life satisfaction (LS) respectively, both directly and indirectly mediated via Sense of Coherence and self-esteem. Based on a cross-sectional population-survey (N=865) in a medium size Norwegian municipality, we specified a structural equation model (SEM) including the above-listed variables, while controlling for gender, age, education, income, and employment status. The applied model explains more variance in LS (46%) than in SRH (23%). Social capital has a stronger impact on life satisfaction than on health. The indirect pathway via SOC had the highest impact on life satisfaction, but no significant relationship to SRH. Self-rated health was more tightly linked to personal background variables. Enhancing social capital in the neighborhood might be a beneficial strategy to promote life satisfaction, as well as strengthening sense of coherence even in healthy communities. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

乳酸扩链聚合物的降解性能%DEGRADABLE BEHAVIORS OF LACTIDE CHAIN-EXTENED POLYMERS

Institute of Scientific and Technical Information of China (English)

封瑞江

2001-01-01

In this paper,the effects of change of degradable rate and relative molecular mass on the degradable behaviors of four lactide chain-extened polymers are contrasted with those of lactide polymers.The results indicated that the four lactide chain-extened polymers could degrade in this experiment and their degradable rate were lower than that of P-LA.LA-SDI has the highest degradable rates among the four lactide chain-extened polymers,but there was no significant difference among aromatic and aliphatic lactide chain-extened polymers.The results showed that the degradable rates were dependent on experiment methods and condition and also indicated that the relative molecular mass became smaller and smaller with the progress of degradation time.

Microcantilever sensors for fast analysis of enzymatic degradation of poly (D, L-lactide)

DEFF Research Database (Denmark)

Bose, Sanjukta; Keller, Stephan Sylvest; Boisen, Anja

2015-01-01

of the biodegradation rate of PDLLA with a minute amount of sample and without the need of thermal and chemical acceleration. The degradation rate of the polymer has been estimated by multilayer cantilever theory and model simulation. A bulk degradation rate of 0.24 μg mm-2 hour-1 is estimated which agrees well...

Effects of fatigue on the chemical and mechanical degradation of model stent sub-units.

Science.gov (United States)

Dreher, Maureen L; Nagaraja, Srinidhi; Batchelor, Benjamin

2016-06-01

Understanding the fatigue and durability performance of implantable cardiovascular stents is critical for assessing their performance. When the stent is manufactured from an absorbable material, however, this durability assessment is complicated by the transient nature of the device. Methodologies for evaluating the fatigue performance of absorbable stents while accurately simulating the degradation are limited and little is known about the interaction between fatigue and degradation. In this study, we investigated the fatigue behavior and effect of fatigue on the degradation rate for a model absorbable cardiovascular stent. Custom v-shaped stent sub-units manufactured from poly(L-lactide), i.e., PLLA, were subjected to a simultaneous fatigue and degradation study with cycle counts representative of one year of expected in vivo use. Fatigue loading was carried out such that the polymer degraded at a rate that was aligned with a modest degree of fatigue acceleration. Control, un-loaded specimens were also degraded under static immersion conditions representative of simulated degradation without fatigue. The study identified that fatigue loading during degradation significantly increased specimen stiffness and lowered the force at break. Fatigue loading also significantly increased the degree of molecular weight decline highlighting an interaction between mechanical loading and chemical degradation. This study demonstrates that fatigue loading during degradation can affect both the mechanical properties and the chemical degradation rate. The results are important for defining appropriate in vitro degradation conditions for absorbable stent preclinical evaluation. Published by Elsevier Ltd.

Concentrated Light for Accelerated Photo Degradation of Polymer Materials

DEFF Research Database (Denmark)

Madsen, Morten Vesterager; Tromholt, Thomas; Norrman, Kion

2013-01-01

Concentrated light is used to perform photochemical degradation of polymer solar cell materials with acceleration factors up to 1200. At constant temperature the photon efficiency in regards to photo degradation is constant for 1–150 suns and oxygen diffusion rates are not a limiting factor...

Evaluation of the performance degradation at PAFC effect of operating conditions on acid loss

Energy Technology Data Exchange (ETDEWEB)

Miyoshi, Hideaki; Uchida, Hiroyuki; Watanabe, Masahiro [Yamanashi Univ., Kofu (Japan)] [and others

1996-12-31

As a complimentary research project to the demonstration project of 5MW and 1 MW PAFC plants, the mechanism and rate of deterioration of the cells and stacks have been studied from 1995 FY conducted by NEDO, with the objective of establishing an estimation method for the service life-time of the cell stacks. As part of this project, this work has been performed to clarify basic phenomena of the performance degradation at PAFCs jointly by Yamanashi University, PAFC-TRA and PAFC manufacturers. The acid loss into exhaust gases is one of life limiting factors in PAFCs. To design the cells of long-life, it is important to estimate the phosphoric acid loss and to contrive ideas eliminating it. With the objective of obtaining basic data for simulating the acid loss in the large size cells, the effect of the operating conditions on the acid loss into exhaust gases has been studied experimentally by using a single cell with an active electrode area of 100 cm{sup 2}.

Effects of Two Surfactants and Beta-Cyclodextrin on Beta-Cypermethrin Degradation by Bacillus licheniformis B-1.

Science.gov (United States)

Zhao, Jiayuan; Chi, Yuanlong; Liu, Fangfang; Jia, Dongying; Yao, Kai

2015-12-23

The biodegradation efficiency of beta-cypermethrin (β-CY) is low especially at high concentrations mainly due to poor contact between this hydrophobic pesticide and microbial cells. In this study, the effects of two biodegradable surfactants (Tween-80 and Brij-35) and β-cyclodextrin (β-CD) on the growth and cell surface hydrophobicity (CSH) of Bacillus licheniformis B-1 were studied. Furthermore, their effects on the solubility, biosorption, and degradation of β-CY were investigated. The results showed that Tween-80 could slightly promote the growth of the strain while Brij-35 and β-CD exhibited little effect on its growth. The CSH of strain B-1 and the solubility of β-CY were obviously changed by using Tween-80 and Brij-35. The surfactants and β-CD could enhance β-CY biosorption and degradation by the strain, and the highest degradation was obtained in the presence of Brij-35. When the surfactant or β-CD concentration was 2.4 g/L, the degradation rate of β-CY in Brij-35, Tween-80, and β-CD treatments was 89.4%, 50.5%, and 48.1%, respectively. The half-life of β-CY by using Brij-35 was shortened by 69.1 h. Beta-CY content in the soil with both strain B-1 and Brij-35 decreased from 22.29 mg/kg to 4.41 mg/kg after incubation for 22 d. This work can provide a promising approach for the efficient degradation of pyrethroid pesticides by microorganisms.

The mutant strain of ZHJ6 degrading organophosphorous pesticide by 60Co-γ irradiation

International Nuclear Information System (INIS)

Zhao Renbang; Chi Jian; He Yi

2013-01-01

The strain of Penicillium oxalicum ZHJ6 that can degrade methamidophos was employed to obtain the mutant stain which has higher degradation rate than original strain by 60 Co-γ irradiation. Results showed that the Penicillium oxalicum ZHJ6 was sensitive to 60 Co-γ irradiation, and was easy to be killed by 60 Co-γ irradiation. Under the absorbed dose of 2.1 kGy, the survival rate of the strain was 0.04%. Two strains of A17 and A18 were obtained from the irradiated strains after first- and second- screening and the degradation rate of methamidophos of A17 and A18 strains were 10% higher than that of A0 strain (original stain). Moreover, the abilities to degrade folimat, phoxim and glyphosate were improved. Through 5 generations, the variation coefficient in degradation rate of methamidophos in the 6th day was 1.2%, showing that the new strains had hereditary stability. (authors)

Improvement of bench life-tests for automotive batteries

Science.gov (United States)

Richter, G.

A common method for rating the endurance of automotive batteries is the bench life-test according to DIN, IEC, SAE or JIS. With an increasing number of maintenance-free batteries on the market, the application of these tests becomes more problematic. This is due to a step-by-step capacity decline during cycling if the content of autimony in the grid-alloy is decreased. The degradation in performance is caused by the phenomenon of acid stratification. Because this debilitating effect occurs only rarely in service (vehicle movement) if charging and discharging is well balanced, there is a need for a new bench life-test with conditions that are more representative of practical conditions. Research has shown that the main changes should be: (i) an accelerated (moved) battery during cycling; (ii) slightly lower charging or discharging capacity amplitude, also with a lower mean value.

Development of degradation prediction technology for rotating machines

International Nuclear Information System (INIS)

Osaki, Kenji; Watanabe, Yukio; Kitajima, Yasumi; Hattori, Hitoshi; Uhara, Yoshihiko; Miyoshi, Toshiaki; O'shima, Eiji

1999-01-01

In order to rationalize facility maintenance management, it is desirable to develop degradation prediction technologies that reduce the workload for example of replacing worn bearings of rotating machines. For this purpose, we are developing a system that performs degradation prediction respecting casing deformation, curvature and crack of shaft, bearing sleeve corrosion, and bearing wear for primary loop recirculation (PLR) pumps, which are important equipment in BWR plants, and for sea water pumps whose bearings are replaced frequently. By means of a physical model of degradation that takes into account various degradation phenomena, this system performs life estimation, taking into consideration the distribution of the vibration characteristic caused by the differences in assembling processes and the distribution of the degradation characteristic. The design of the degradation prediction system was examined and a part of the analysis method was developed. The bearing characteristic analysis with consideration to surface roughness was performed and the vibration response analysis evaluated the effects of factors influencing vibration characteristics of pump, such as bearing misalignment, on bearing forces. The component test of an upper bearing of 1/2 scale PLR pump motor was carried out, and the bearing wear characteristic was clarified. The research was carried out by the Japan Power Engineering and Inspection Corporation (JAPEIC) which was entrusted by the Ministry of International Trade and Industry (MITI). (author)

Age identity, self-rated health, and life satisfaction among older adults in Dakar, Senegal.

Science.gov (United States)

Macia, Enguerran; Duboz, Priscilla; Montepare, Joann M; Gueye, Lamine

2012-09-01

The objectives of this quantitative study were to (1) ascertain to what extent older adults aged 50 and above feel and desire to be younger than their age, and classify themselves as young versus old; (2) compare these patterns with those found among other cross-cultural populations; and (3) assess the extent to which self-rated health and life satisfaction predict age identities. This study was carried out on a sample of 500 dwellers of the Senegalese capital aged 50 and older. This sample was constructed using the quota method to strive for representativeness. Most of the respondents wanted to be younger than their chronological age (51.8 %), but only 27.8 % felt younger than they were. Moreover, 80 % of the sample claimed to be old. Self-rated health predicted felt age and the feeling of being old. Furthermore, the less-satisfied Dakar residents were with their life, the younger they wanted to be. We first discuss our results in a comparative perspective focused on how orientations toward individualism and collectivism could be related to age identity, and on demographic characteristics of the Senegalese population-where life expectancy is 59.3 years old. We then analyze the relevance of age identity dimensions as indicators of successful aging in Dakar.

Study on the Degradation of Polylactide Microsphere In Vitro

Institute of Scientific and Technical Information of China (English)

HeYing; WeiShuli

2001-01-01

This report concentrated on the rules and mechanism of the degradation of polylactide and the microspheres. The rate of degradation was assessed with five methods: observation of microsphere surface morphology by SEM, determination of the weight loss of the microspheres, determination of the molecular mass of the polymers by GPC, determination of pH and determination of the contents of lactic acid by UV spectrophotometry. The degradation of polylactide microspheres showed two-phase characteristics. At the early stage of the degradation, the high molecular mass polymers were cleaved into lower molecular mass fractions and at the late stage, there was a period of erosion and weight loss of the microspheres. The degradation was much slower for polymers with a higher molecular mass. The polylactide degradation showed good regularity.

Degradation of CIGS solar cells

NARCIS (Netherlands)

Theelen, M.J.

2015-01-01

Large scale commercial introduction of CIGS photovoltaics (PV) requires modules with low costs, high efficiencies and long and predictable lifetimes. Unfortunately,knowledge about the lifetime of CIGS PV is limited, which is reflected in the results of field studies: degradation rates varying from

Degradation of carbazole, dibenzothiophene, and dibenzofuran at low temperature by Pseudomonas sp. strain C3211.

Science.gov (United States)

Jensen, Anne-Mette; Finster, Kai Waldemar; Karlson, Ulrich

2003-04-01

Pseudomonas sp. strain C3211 was isolated from a temperate climate soil contaminated with creosote. This strain was able to degrade carbazole, dibenzothiophene and dibenzofuran at 10 degrees C with acetone as a co-substrate. When dibenzothiophene was degraded by strain C3211, an orange compound, which absorbed at 472 nm, accumulated in the medium. Degradation of dibenzofuran was followed by accumulation of a yellowish compound, absorbing at 462 nm. The temperature optimum of strain C3211 for degradation of dibenzothiophene and dibenzofuran was at 20 to 21 degrees C, while the maximum temperature for degradation was at 27 degrees C. Both compounds were degraded at 4 degrees C. Degradation at 10 degrees C was faster than degradation at 25 degrees C. This indicates that strain C3211 is adapted to life at low temperatures.

Effects of frequency and a radical scavenger on ultrasonic degradation of water-soluble polymers.