WorldWideScience

Sample records for level rules engine

  1. Intelligent wear mode identification system for marine diesel engines based on multi-level belief rule base methodology

    Science.gov (United States)

    Yan, Xinping; Xu, Xiaojian; Sheng, Chenxing; Yuan, Chengqing; Li, Zhixiong

    2018-01-01

    Wear faults are among the chief causes of main-engine damage, significantly influencing the secure and economical operation of ships. It is difficult for engineers to utilize multi-source information to identify wear modes, so an intelligent wear mode identification model needs to be developed to assist engineers in diagnosing wear faults in diesel engines. For this purpose, a multi-level belief rule base (BBRB) system is proposed in this paper. The BBRB system consists of two-level belief rule bases, and the 2D and 3D characteristics of wear particles are used as antecedent attributes on each level. Quantitative and qualitative wear information with uncertainties can be processed simultaneously by the BBRB system. In order to enhance the efficiency of the BBRB, the silhouette value is adopted to determine referential points and the fuzzy c-means clustering algorithm is used to transform input wear information into belief degrees. In addition, the initial parameters of the BBRB system are constructed on the basis of expert-domain knowledge and then optimized by the genetic algorithm to ensure the robustness of the system. To verify the validity of the BBRB system, experimental data acquired from real-world diesel engines are analyzed. Five-fold cross-validation is conducted on the experimental data and the BBRB is compared with the other four models in the cross-validation. In addition, a verification dataset containing different wear particles is used to highlight the effectiveness of the BBRB system in wear mode identification. The verification results demonstrate that the proposed BBRB is effective and efficient for wear mode identification with better performance and stability than competing systems.

  2. High Level Rule Modeling Language for Airline Crew Pairing

    Science.gov (United States)

    Mutlu, Erdal; Birbil, Ş. Ilker; Bülbül, Kerem; Yenigün, Hüsnü

    2011-09-01

    The crew pairing problem is an airline optimization problem where a set of least costly pairings (consecutive flights to be flown by a single crew) that covers every flight in a given flight network is sought. A pairing is defined by using a very complex set of feasibility rules imposed by international and national regulatory agencies, and also by the airline itself. The cost of a pairing is also defined by using complicated rules. When an optimization engine generates a sequence of flights from a given flight network, it has to check all these feasibility rules to ensure whether the sequence forms a valid pairing. Likewise, the engine needs to calculate the cost of the pairing by using certain rules. However, the rules used for checking the feasibility and calculating the costs are usually not static. Furthermore, the airline companies carry out what-if-type analyses through testing several alternate scenarios in each planning period. Therefore, embedding the implementation of feasibility checking and cost calculation rules into the source code of the optimization engine is not a practical approach. In this work, a high level language called ARUS is introduced for describing the feasibility and cost calculation rules. A compiler for ARUS is also implemented in this work to generate a dynamic link library to be used by crew pairing optimization engines.

  3. Engineering at the Elementary Level

    Science.gov (United States)

    McGrew, Cheryl

    2012-01-01

    Can engineering technology be taught at the elementary level? Designing and building trebuchets, catapults, solar cars, and mousetrap vehicles in a west central Florida elementary class was considered very unusual in recent years. After a review of current research on failing schools and poor curriculum, the author wondered what her school could…

  4. Interactive Synthesis of Code Level Security Rules

    Science.gov (United States)

    2017-04-01

    Proceedings of the 9th ACM conference on Computer and communications security, pages 235–244. ACM, 2002. [19] J. Davis. Hacking of government computers...Inductive programming meets the real world. Communications of the ACM, 58(11):90–99, 2015. [24] S. Hallem, B. Chelf, Y. Xie, and D. Engler. A system and...Software Engineering, pages 462–473. ACM, 2015. [37] S. H. Muggleton, D. Lin, and A. Tamaddoni-Nezhad. Meta-interpretive learning of higher- order dyadic

  5. Decision tables and rule engines in organ allocation systems for optimal transparency and flexibility

    NARCIS (Netherlands)

    Schaafsma, M.; Deijl, W. van der; Smits, J.M.M.; Rahmel, A.O.; Vries Robbé, P.F. de; Hoitsma, A.J.

    2011-01-01

    Organ allocation systems have become complex and difficult to comprehend. We introduced decision tables to specify the rules of allocation systems for different organs. A rule engine with decision tables as input was tested for the Kidney Allocation System (ETKAS). We compared this rule engine with

  6. Rule-based emergency action level monitor prototype

    International Nuclear Information System (INIS)

    Touchton, R.A.; Gunter, A.D.; Cain, D.

    1985-01-01

    In late 1983, the Electric Power Research Institute (EPRI) began a program to encourage and stimulate the development of artificial intelligence (AI) applications for the nuclear industry. Development of a rule-based emergency action level classification system prototype is discussed. The paper describes both the full prototype currently under development and the completed, simplified prototype

  7. Nutrient fluxes at the landscape level and the R* rule

    Science.gov (United States)

    Ju, Shu; DeAngelis, Donald L.

    2010-01-01

    Nutrient cycling in terrestrial ecosystems involves not only the vertical recycling of nutrients at specific locations in space, but also biologically driven horizontal fluxes between different areas of the landscape. This latter process can result in net accumulation of nutrients in some places and net losses in others. We examined the effects of such nutrient-concentrating fluxes on the R* rule, which predicts that the species that can survive in steady state at the lowest level of limiting resource, R*, can exclude all competing species. To study the R* rule in this context, we used a literature model of plant growth and nutrient cycling in which both nutrients and light may limit growth, with plants allocating carbon and nutrients between foliage and roots according to different strategies. We incorporated the assumption that biological processes may concentrate nutrients in some parts of the landscape. We assumed further that these processes draw nutrients from outside the zone of local recycling at a rate proportional to the local biomass density. Analysis showed that at sites where there is a sufficient biomass-dependent accumulation of nutrients, the plant species with the highest biomass production rates (roughly corresponding to the best competitors) do not reduce locally available nutrients to a minimum concentration level (that is, minimum R*), as expected from the R* rule, but instead maximize local nutrient concentration. These new results require broadening of our understanding of the relationships between nutrients and vegetation competition on the landscape level. The R* rule is replaced by a more complex criterion that varies across a landscape and reduces to the R* rule only under certain limiting conditions.

  8. Decision tables and rule engines in organ allocation systems for optimal transparency and flexibility.

    Science.gov (United States)

    Schaafsma, Murk; van der Deijl, Wilfred; Smits, Jacqueline M; Rahmel, Axel O; de Vries Robbé, Pieter F; Hoitsma, Andries J

    2011-05-01

    Organ allocation systems have become complex and difficult to comprehend. We introduced decision tables to specify the rules of allocation systems for different organs. A rule engine with decision tables as input was tested for the Kidney Allocation System (ETKAS). We compared this rule engine with the currently used ETKAS by running 11,000 historical match runs and by running the rule engine in parallel with the ETKAS on our allocation system. Decision tables were easy to implement and successful in verifying correctness, completeness, and consistency. The outcomes of the 11,000 historical matches in the rule engine and the ETKAS were exactly the same. Running the rule engine simultaneously in parallel and in real time with the ETKAS also produced no differences. Specifying organ allocation rules in decision tables is already a great step forward in enhancing the clarity of the systems. Yet, using these tables as rule engine input for matches optimizes the flexibility, simplicity and clarity of the whole process, from specification to the performed matches, and in addition this new method allows well controlled simulations. © 2011 The Authors. Transplant International © 2011 European Society for Organ Transplantation.

  9. A high-level language for rule-based modelling.

    Science.gov (United States)

    Pedersen, Michael; Phillips, Andrew; Plotkin, Gordon D

    2015-01-01

    Rule-based languages such as Kappa excel in their support for handling the combinatorial complexities prevalent in many biological systems, including signalling pathways. But Kappa provides little structure for organising rules, and large models can therefore be hard to read and maintain. This paper introduces a high-level, modular extension of Kappa called LBS-κ. We demonstrate the constructs of the language through examples and three case studies: a chemotaxis switch ring, a MAPK cascade, and an insulin signalling pathway. We then provide a formal definition of LBS-κ through an abstract syntax and a translation to plain Kappa. The translation is implemented in a compiler tool which is available as a web application. We finally demonstrate how to increase the expressivity of LBS-κ through embedded scripts in a general-purpose programming language, a technique which we view as generally applicable to other domain specific languages.

  10. Update on ASME rules for spent nuclear fuel and high level radioactive material and waste storage containments

    International Nuclear Information System (INIS)

    Ralph S. Hill III; Foster, G.M.

    2005-01-01

    In 2004, a new Code Case, N-717, of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (Code) was published. The Code Case provides rules for construction of containments used for storage of spent nuclear fuel and high level radioactive material and waste. The Code Case has been incorporated into Section III of the Code as Division 3, Subsection WC, Class SC Storage Containments, and will be published in the 2005 Addenda. This paper provides an informative background and insight for these rules to provide Owners, regulators, designers, and fabricators with a more comprehensive understanding of the technical basis for these rules. (authors)

  11. 22 CFR 228.39 - Special source rules for construction and engineering services.

    Science.gov (United States)

    2010-04-01

    ... engineering services. 228.39 Section 228.39 Foreign Relations AGENCY FOR INTERNATIONAL DEVELOPMENT RULES ON SOURCE, ORIGIN AND NATIONALITY FOR COMMODITIES AND SERVICES FINANCED BY USAID Conditions Governing the... engineering services. Advanced developing countries, eligible under Geographic Code 941, which have attained a...

  12. Agile Service Development: A Rule-Based Method Engineering Approach

    NARCIS (Netherlands)

    dr. Martijn Zoet; Stijn Hoppenbrouwers; Inge van de Weerd; Johan Versendaal

    2011-01-01

    Agile software development has evolved into an increasingly mature software development approach and has been applied successfully in many software vendors’ development departments. In this position paper, we address the broader agile service development. Based on method engineering principles we

  13. Correcting groove error in gratings ruled on a 500-mm ruling engine using interferometric control.

    Science.gov (United States)

    Mi, Xiaotao; Yu, Haili; Yu, Hongzhu; Zhang, Shanwen; Li, Xiaotian; Yao, Xuefeng; Qi, Xiangdong; Bayinhedhig; Wan, Qiuhua

    2017-07-20

    Groove error is one of the most important factors affecting grating quality and spectral performance. To reduce groove error, we propose a new ruling-tool carriage system based on aerostatic guideways. We design a new blank carriage system with double piezoelectric actuators. We also propose a completely closed-loop servo-control system with a new optical measurement system that can control the position of the diamond relative to the blank. To evaluate our proposed methods, we produced several gratings, including an echelle grating with 79  grooves/mm, a grating with 768  grooves/mm, and a high-density grating with 6000  grooves/mm. The results show that our methods effectively reduce groove error in ruled gratings.

  14. French en engineering and operation rules for plutonium facilities

    International Nuclear Information System (INIS)

    Bertolotti, G.; Drain, F.; Dubois, G.; Monnatte, J.; Mathieu, P.

    1998-01-01

    COGEMA is operating large size purifying and conditioning plutonium facilities at LA HAGUE and MOX fuels fabrication plant at Marcoule. A high safety standard is recognised for these facilities. It is mainly based on : - prevention of spreading of radioactive materials to workers and environment by physical barriers ensuring static containment and by a cascade of pressure differentials ensuring dynamic containment, - radiation shielding and remote controlled processes ensuring very low dose to workers, - prevention of criticality accident by criticality control methods and double contingency principle, - prevention of fire risks by control of ignition sources, adequate management of combustible materials, physical separation between zones where there is a risk of fire and the remainder of the facility. The facilities are operated while respecting safety requirements as described in the General Operating Rules. The equipment involved in safety functions are monitored and periodically checked. Continuous improvement by incorporation of feed back of safety experience results in: - effective decrease of exposure to operating staff; - reduction of solid waste, liquid and gaseous effluents; - no significant incident recorded. (author)

  15. International Rules for Pre-College Science Research: Guidelines for Science and Engineering Fairs, 2010-2011

    Science.gov (United States)

    Society for Science & the Public, 2011

    2011-01-01

    This paper presents the rules and guidelines of the Intel International Science and Engineering Fair 2011 to be held in Los Angeles, California in May 8-13, 2011. In addition to providing the rules of competition, these rules and guidelines for conducting research were developed to facilitate the following: (1) protect the rights and welfare of…

  16. Low-level radwaste engineering economics

    International Nuclear Information System (INIS)

    Jacobs, M.H.; Miller, C.C.; Young, L.G.

    1984-07-01

    This topical report on engineering economics for low-level radwaste systems details the methodologies used for economic analyses of radwaste treatment systems and provides examples of radwaste economic evaluations. All of the parameters and cost items used in an evaluation are defined. Examples of the present-value-of-revenue-requirements method, levelized-revenue-requirements method, and the equivalent-capital-investment method are provided. Also, the calculation to determine the maximum justifiable capital expenditure for a radwaste system is illustrated. The report also provides examples of economic evaluations for many current radwaste treatment options. These options include evaporation versus demineralization, dewatering resins versus solidification of resins, and several volume reduction systems. 15 figures, 6 tables

  17. Radial oil injection applied to main engine bearings: evaluation of injection control rules

    DEFF Research Database (Denmark)

    Estupiñan, EA; Santos, Ilmar

    2012-01-01

    , the dynamic behaviour of the main bearing of a medium-size engine is theoretically analysed when the engine operates with controllable radial oil injection and four different injection control rules. The theoretical investigation is based on a single-cylinder combustion engine model. The performance......The performance of main bearings in a combustion engine affects key functions such as durability, noise and vibration. Thus, with the aim of reducing friction losses and vibrations between the crankshaft and the bearings, the work reported here evaluates different strategies for applying...... controllable radial oil injection to main crankshaft journal bearings. In an actively lubricated bearing, conventional hydrodynamic lubrication is combined with controllable hydrostatic lubrication, where the oil injection pressures can be modified depending on the operational conditions. In this study...

  18. Usage of the Jess Engine, Rules and Ontology to Query a Relational Database

    Science.gov (United States)

    Bak, Jaroslaw; Jedrzejek, Czeslaw; Falkowski, Maciej

    We present a prototypical implementation of a library tool, the Semantic Data Library (SDL), which integrates the Jess (Java Expert System Shell) engine, rules and ontology to query a relational database. The tool extends functionalities of previous OWL2Jess with SWRL implementations and takes full advantage of the Jess engine, by separating forward and backward reasoning. The optimization of integration of all these technologies is an advancement over previous tools. We discuss the complexity of the query algorithm. As a demonstration of capability of the SDL library, we execute queries using crime ontology which is being developed in the Polish PPBW project.

  19. Prospects of increasing the engineering level of NPP components

    International Nuclear Information System (INIS)

    Filippov, G.A.

    1987-01-01

    Consideration is being given to main problems related to development and industrial introduction of NPP components corresponding to the perspective world-wide engineering level. The nearest task in this field is to elevate the engineering level of developed and being produced power equipment up to the level of similar equipment, manufactured by leading foreign companies

  20. A Compositional Knowledge Level Process Model of Requirements Engineering

    NARCIS (Netherlands)

    Herlea, D.E.; Jonker, C.M.; Treur, J.; Wijngaards, W.C.A.

    2002-01-01

    In current literature few detailed process models for Requirements Engineering are presented: usually high-level activities are distinguished, without a more precise specification of each activity. In this paper the process of Requirements Engineering has been analyzed using knowledge-level

  1. New Laboratory Course for Senior-Level Chemical Engineering Students

    Science.gov (United States)

    Aronson, Mark T.; Deitcher, Robert W.; Xi, Yuanzhou; Davis, Robert J.

    2009-01-01

    A new laboratory course has been developed at the University of Virginia for senior- level chemical engineering students. The new course is based on three 4-week long experiments in bioprocess engineering, energy conversion and catalysis, and polymer synthesis and characterization. The emphasis is on the integration of process steps and the…

  2. Introductory Level Problems Illustrating Concepts in Pharmaceutical Engineering

    Science.gov (United States)

    McIver, Keith; Whitaker, Kathryn; De Delva, Vladimir; Farrell, Stephanie; Savelski, Mariano J.; Slater, C. Stewart

    2012-01-01

    Textbook style problems including detailed solutions introducing pharmaceutical topics at the level of an introductory chemical engineering course have been created. The problems illustrate and teach subjects which students would learn if they were to pursue a career in pharmaceutical engineering, including the unique terminology of the field,…

  3. Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

    Science.gov (United States)

    Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

  4. Uprated OMS Engine Status-Sea Level Testing Results

    Science.gov (United States)

    Bertolino, J. D.; Boyd, W. C.

    1990-01-01

    The current Space Shuttle Orbital Maneuvering Engine (OME) is pressure fed, utilizing storable propellants. Performance uprating of this engine, through the use of a gas generator driven turbopump to increase operating pressure, is being pursued by the NASA Johnson Space Center (JSC). Component level design, fabrication, and test activities for this engine system have been on-going since 1984. More recently, a complete engine designated the Integrated Component Test Bed (ICTB), was tested at sea level conditions by Aerojet. A description of the test hardware and results of the sea level test program are presented. These results, which include the test condition operating envelope and projected performance at altitude conditions, confirm the capability of the selected Uprated OME (UOME) configuration to meet or exceed performance and operational requirements. Engine flexibility, demonstrated through testing at two different operational mixture ratios, along with a summary of projected Space Shuttle performance enhancements using the UOME, are discussed. Planned future activities, including ICTB tests at simulated altitude conditions, and recommendations for further engine development, are also discussed.

  5. Evaluating changes to reservoir rule curves using historical water-level data

    Science.gov (United States)

    Mower, Ethan; Miranda, Leandro E.

    2013-01-01

    Flood control reservoirs are typically managed through rule curves (i.e. target water levels) which control the storage and release timing of flood waters. Changes to rule curves are often contemplated and requested by various user groups and management agencies with no information available about the actual flood risk of such requests. Methods of estimating flood risk in reservoirs are not easily available to those unfamiliar with hydrological models that track water movement through a river basin. We developed a quantile regression model that uses readily available daily water-level data to estimate risk of spilling. Our model provided a relatively simple process for estimating the maximum applicable water level under a specific flood risk for any day of the year. This water level represents an upper-limit umbrella under which water levels can be operated in a variety of ways. Our model allows the visualization of water-level management under a user-specified flood risk and provides a framework for incorporating the effect of a changing environment on water-level management in reservoirs, but is not designed to replace existing hydrological models. The model can improve communication and collaboration among agencies responsible for managing natural resources dependent on reservoir water levels.

  6. Sea-level rise and shoreline retreat: time to abandon the Bruun Rule

    Science.gov (United States)

    Cooper, J. Andrew G.; Pilkey, Orrin H.

    2004-11-01

    In the face of a global rise in sea level, understanding the response of the shoreline to changes in sea level is a critical scientific goal to inform policy makers and managers. A body of scientific information exists that illustrates both the complexity of the linkages between sea-level rise and shoreline response, and the comparative lack of understanding of these linkages. In spite of the lack of understanding, many appraisals have been undertaken that employ a concept known as the "Bruun Rule". This is a simple two-dimensional model of shoreline response to rising sea level. The model has seen near global application since its original formulation in 1954. The concept provided an advance in understanding of the coastal system at the time of its first publication. It has, however, been superseded by numerous subsequent findings and is now invalid. Several assumptions behind the Bruun Rule are known to be false and nowhere has the Bruun Rule been adequately proven; on the contrary several studies disprove it in the field. No universally applicable model of shoreline retreat under sea-level rise has yet been developed. Despite this, the Bruun Rule is in widespread contemporary use at a global scale both as a management tool and as a scientific concept. The persistence of this concept beyond its original assumption base is attributed to the following factors: Appeal of a simple, easy to use analytical model that is in widespread use. Difficulty of determining the relative validity of 'proofs' and 'disproofs'. Ease of application. Positive advocacy by some scientists. Application by other scientists without critical appraisal. The simple numerical expression of the model. Lack of easy alternatives. The Bruun Rule has no power for predicting shoreline behaviour under rising sea level and should be abandoned. It is a concept whose time has passed. The belief by policy makers that it offers a prediction of future shoreline position may well have stifled much

  7. Scaling properties of S-wave level density for heavy quarkonium from QCD sum rules

    International Nuclear Information System (INIS)

    Kiselev, V.V.

    1994-01-01

    In the framework of a specific scheme of the QCD sum rules for S-wave of the heavy quarkonium one derives an expression, relating the energetic density of quarkonium states and universal characteristics in the heavy quarkonium physics, such as the difference between the masses of a heavy quark Q and meson and the number of heavy quarkonium levels below the threshold decay. 20 refs

  8. Large-scale double-patterning compliant layouts for DP engine and design rule development

    Science.gov (United States)

    Cork, Christopher; Lucas, Kevin; Hapli, John; Raffard, Herve; Barnes, Levi

    2009-03-01

    Double Patterning is seen as the prime technology to keep Moore's law on path while EUV technology is still maturing into production worthiness. As previously seen for alternating-Phase Shift Mask technology[1], layout compliance of double patterning is not trivial [2,3] and blind shrinks of anything but the most simplistic existing layouts, will not be directly suitable for double patterning. Evaluating a production worthy double patterning engine with highly non-compliant layouts would put unrealistic expectations on that engine and provide metrics with poor applicability for eventual large designs. The true production use-case would be for designs that have at least some significant double patterning compliance already enforced at the design stage. With this in mind a set of ASIC design blocks of different sizes and complexities were created that were double patterning compliant. To achieve this, a set of standard cells were generated, which individually and in isolation were double patterning compliant, for multiple layers simultaneously. This was done using the automated Standard Cell creation tool CadabraTM [4]. To create a full ASIC, however, additional constraints were added to make sure compliance would not be broken across the boundaries between standard cells when placed next to each other [5]. These standard cells were then used to create a variety of double patterning compliant ASICs using iCCompilerTM to place the cells correctly. Now with a compliant layout, checks were made to see if the constraints made at the micro level really do ensure a fully compliant layout on the whole chip and if the coloring engine could cope with such large datasets. A production worthy double patterning engine is ideally distributable over multiple processors [6,7] so that fast turn-around time can be achievable on even the largest designs. We demonstrate the degree of linearity of scaling achievable with our double patterning engine. These results can be understood

  9. Leveling the Playing Field: Teacher Perception of Integrated STEM, Engineering, and Engineering Practices

    Science.gov (United States)

    Fincher, Bridgette Ann

    The purpose of this study was to describe the perceptions and approaches of 14 third-through-fifth grade Arkansan elementary teachers towards integrative engineering and engineering practices during 80 hours of integrated STEM professional development training in the summer and fall of 2014. This training was known as Project Flight. The purpose of the professional development was to learn integrated STEM content related to aviation and to write grade level curriculum units using Wiggins and McTighe's Understanding by Design curriculum framework. The current study builds upon on the original research. Using a mixed method exploratory, embedded QUAL[quan] case study design and a non-experimental convenience sample derived from original 20 participants of Project Flight, this research sought to answer the following question: Does professional development influence elementary teachers' perceptions of the curriculum and instruction of integrated STEM engineering and engineering practices in a 3-to-5 grade level setting? A series of six qualitative and one quantitative sub-questions informed the research of the mixed method question. Hermeneutic content analysis was applied to archival and current qualitative data sets while descriptive statistics, independent t-tests, and repeated measures ANOVA tests were performed on the quantitative data. Broad themes in the teachers' perceptions and understanding of the nature of integrated engineering and engineering practices emerged through triangulation. After the professional development and the teaching of the integrated STEM units, all 14 teachers sustained higher perceptions of personal self-efficacy in their understanding of Next Generation Science Standards (NGSS). The teachers gained understanding of engineering and engineering practices, excluding engineering habits of mind, throughout the professional development training and unit teaching. The research resulted in four major findings specific to elementary engineering

  10. Responding to changes in sea level: engineering implications

    National Research Council Canada - National Science Library

    National Research Council Staff; Marine Board; Commission on Engineering and Technical Systems; Division on Engineering and Physical Sciences; National Research Council

    1987-01-01

    ... Mean Sea Level Marine Board Commission on Engineering and Technical Systems National Research Council National Academy Press Washington, D.C. 1987 Copyrightthe cannot be not from book, paper however, version for formatting, original authoritative the typesetting-specific the as from created publication files XML from other this and of recom...

  11. Analisis Performansi Algoritma Penjadwalan Log Rule dan Frame Level Schedule Skenario Multicell Pada Layer Mac LTE

    Directory of Open Access Journals (Sweden)

    Ridwan

    2016-03-01

    Full Text Available Mobile telecommunications technology gradually evolved to support better services such as voice, data, and video to users of telecommunications services. LTE (Long Term Evolution is a network based on Internet Protocol (IP standardized by 3rd Generation Partnership Project (3GPP. To support it, LTE requires a mechanism that can support. One of them by applying methods of scheduling packets in each service. Scheduling is a different treatment to packets that come in accordance with the priorities of the scheduling algorithm. In this research, to analyze the performance of LTE with paramater delay, packet loss ratio, throughput and fairness index uses a scheduling algorithms Frame Level Schedule (FLS and Log Rule on LTE-Simulator with scenarios using Voip traffic, Video and Best Effort (BE. The results is scheduling algorithms FLS is better than log rule in term of throughput values, while of scheduling algorithms log rule is better than FLS in terms of delay based on the number and speed of the users. This indicates that both scheduling algorithms suitable for use in LTE networks within conditions of traffic real time services, but not for non real time services such as BE.

  12. APPLICATION OF ROUGH SET THEORY TO MAINTENANCE LEVEL DECISION-MAKING FOR AERO-ENGINE MODULES BASED ON INCREMENTAL KNOWLEDGE LEARNING

    Institute of Scientific and Technical Information of China (English)

    陆晓华; 左洪福; 蔡景

    2013-01-01

    The maintenance of an aero-engine usually includes three levels ,and the maintenance cost and period greatly differ depending on the different maintenance levels .To plan a reasonable maintenance budget program , airlines would like to predict the maintenance level of aero-engine before repairing in terms of performance parame-ters ,which can provide more economic benefits .The maintenance level decision rules are mined using the histori-cal maintenance data of a civil aero-engine based on the rough set theory ,and a variety of possible models of upda-ting rules produced by newly increased maintenance cases added to the historical maintenance case database are in-vestigated by the means of incremental machine learning .The continuously updated rules can provide reasonable guidance suggestions for engineers and decision support for planning a maintenance budget program before repai-ring .The results of an example show that the decision rules become more typical and robust ,and they are more accurate to predict the maintenance level of an aero-engine module as the maintenance data increase ,which illus-trates the feasibility of the represented method .

  13. Occupational exposure to diesel engine exhaust and serum cytokine levels.

    Science.gov (United States)

    Dai, Yufei; Ren, Dianzhi; Bassig, Bryan A; Vermeulen, Roel; Hu, Wei; Niu, Yong; Duan, Huawei; Ye, Meng; Meng, Tao; Xu, Jun; Bin, Ping; Shen, Meili; Yang, Jufang; Fu, Wei; Meliefste, Kees; Silverman, Debra; Rothman, Nathaniel; Lan, Qing; Zheng, Yuxin

    2018-03-01

    The International Agency for Research on Cancer has classified diesel engine exhaust (DEE) as a human lung carcinogen. Given that inflammation is suspected to be an important underlying mechanism of lung carcinogenesis, we evaluated the relationship between DEE exposure and the inflammatory response using data from a cross-sectional molecular epidemiology study of 41 diesel engine testing workers and 46 unexposed controls. Repeated personal exposure measurements of PM 2.5 and other DEE constituents were taken for the diesel engine testing workers before blood collection. Serum levels of six inflammatory biomarkers including interleukin (IL)-1, IL-6, IL-8, tumor necrosis factor (TNF)-α, macrophage inflammatory protein (MIP)-1β, and monocyte chemotactic protein (MCP)-1 were analyzed in all subjects. Compared to unexposed controls, concentrations of MIP-1β were significantly reduced by ∼37% in DEE exposed workers (P 397 µg/m 3 ) compared to unexposed controls. Further, significant inverse exposure-response relationships for IL-8 and MCP-1 were also found in relation to increasing PM 2.5 levels among the DEE exposed workers. Given that IL-8, MIP-1β, and MCP-1 are chemokines that play important roles in recruitment of immunocompetent cells for immune defense and tumor cell clearance, the observed lower levels of these markers with increasing PM 2.5 exposure may provide insight into the mechanism by which DEE promotes lung cancer. Environ. Mol. Mutagen. 59:144-150, 2018. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  14. A programmable rules engine to provide clinical decision support using HTML forms.

    Science.gov (United States)

    Heusinkveld, J; Geissbuhler, A; Sheshelidze, D; Miller, R

    1999-01-01

    The authors have developed a simple method for specifying rules to be applied to information on HTML forms. This approach allows clinical experts, who lack the programming expertise needed to write CGI scripts, to construct and maintain domain-specific knowledge and ordering capabilities within WizOrder, the order-entry and decision support system used at Vanderbilt Hospital. The clinical knowledge base maintainers use HTML editors to create forms and spreadsheet programs for rule entry. A test environment has been developed which uses Netscape to display forms; the production environment displays forms using an embedded browser.

  15. Engineering materials for high level radioactive waste repository

    International Nuclear Information System (INIS)

    Wen Zhijian

    2009-01-01

    Radioactive wastes can arise from a wide range of human activities and have different physical and chemical forms with various radioactivity. The high level radioactive wastes (HLW)are characterized by nuclides of very high initial radioactivity, large thermal emissivity and the long life-term. The HLW disposal is highly concerned by the scientists and the public in the world. At present, the deep geological disposal is regarded as the most reasonable and effective way to safely dispose high-level radioactive wastes in the world. The conceptual model of HLW geological disposal in China is based on a multi-barrier system that combines an isolating geological environment with an engineering barrier system(EBS). The engineering materials in EBS include the vitrified HLW, canister, overpack, buffer materials and backfill materials. Referring to progress in the world, this paper presents the function, the requirement for material selection and design, and main scientific projects of R and D of engineering materials in HLW repository. (authors)

  16. Engineering-scale vitrification of commercial high-level waste

    International Nuclear Information System (INIS)

    Bonner, W.F.; Bjorklund, W.J.; Hanson, M.S.; Knowlton, D.E.

    1980-04-01

    To date, technology for immobilizing commercial high-level waste (HLW) has been extensively developed, and two major demonstration projects have been completed, the Waste Solidification Engineering Prototypes (WSEP) Program and the Nuclear Waste Vitrification Project (NWVP). The feasibility of radioactive waste solidification was demonstrated in the WSEP program between 1966 and 1970 (McElroy et al. 1972) using simulated power-reactor waste composed of nonradioactive chemicals and HLW from spent, Hanford reactor fuel. Thirty-three engineering-scale canisters of solidified HLW were produced during the operations. In early 79, the NWVP demonstrated the vitrification of HLW from the processing of actual commercial nuclear fuel. This program consisted of two parts, (1) waste preparation and (2) vitrification by spray calcination and in-can melting. This report presents results from the NWVP

  17. Model-based Systems Engineering: Creation and Implementation of Model Validation Rules for MOS 2.0

    Science.gov (United States)

    Schmidt, Conrad K.

    2013-01-01

    Model-based Systems Engineering (MBSE) is an emerging modeling application that is used to enhance the system development process. MBSE allows for the centralization of project and system information that would otherwise be stored in extraneous locations, yielding better communication, expedited document generation and increased knowledge capture. Based on MBSE concepts and the employment of the Systems Modeling Language (SysML), extremely large and complex systems can be modeled from conceptual design through all system lifecycles. The Operations Revitalization Initiative (OpsRev) seeks to leverage MBSE to modernize the aging Advanced Multi-Mission Operations Systems (AMMOS) into the Mission Operations System 2.0 (MOS 2.0). The MOS 2.0 will be delivered in a series of conceptual and design models and documents built using the modeling tool MagicDraw. To ensure model completeness and cohesiveness, it is imperative that the MOS 2.0 models adhere to the specifications, patterns and profiles of the Mission Service Architecture Framework, thus leading to the use of validation rules. This paper outlines the process by which validation rules are identified, designed, implemented and tested. Ultimately, these rules provide the ability to maintain model correctness and synchronization in a simple, quick and effective manner, thus allowing the continuation of project and system progress.

  18. Design rules for piping: Plastic stability of straight parts under level D loadings

    International Nuclear Information System (INIS)

    Touboul, F.; Ben Djidia, M.; Acker, D.

    1989-01-01

    Design rules for piping, elaborated for Fast Breeder Reactors, are based on analysis performed for Pressure Water Reactors. Interpretation of largely diversified straight parts tests, enable us to validate and improve existing rules and to propose a more suitable formula. Design rules for piping appear to be non conservative for austenitic thin tubes in bending or torsion. By introducing a B 2 coefficient, geometrically dependent, the gap between thin and thick tubes may be withheld. Conservatism of rules can be ensured by considering the allowable stress defined by ASME, Section III, Appendix F

  19. Australian road rules

    Science.gov (United States)

    2009-02-01

    *These are national-level rules. Australian Road Rules - 2009 Version, Part 18, Division 1, Rule 300 "Use of Mobile Phones" describes restrictions of mobile phone use while driving. The rule basically states that drivers cannot make or receive calls ...

  20. The UNGA Resolutions on the Rule of Law at the National and International Levels, 2006-Post 2015

    NARCIS (Netherlands)

    Janse, R.

    2014-01-01

    For almost a decade, the un General Assembly (unga) has adopted annual resolutions on ‘the rule of law at the national and international levels.’ Moreover, the unga has held a High-level Meeting in September 2012 where Heads of State and Government discussed the topic for the first time ever and

  1. Monetary Policy Rules, Supply Shocks, and the Price-Level Elasticity of Aggregate Demand: A Graphical Examination.

    Science.gov (United States)

    Kyer, Ben L.; Maggs, Gary E.

    1995-01-01

    Utilizes two-dimensional price and output graphs to demonstrate the way that the price-level elasticity of aggregate demand affects alternative monetary policy rules designed to cope with random aggregate supply shocks. Includes graphs illustrating price-level, real Gross Domestic Product (GDP), nominal GDP, and nominal money supply targeting.…

  2. Radiative E1-decay of charmonium 1P1 level within sum rules of quantum chromodynamics

    International Nuclear Information System (INIS)

    Martynenko, A.P.

    1991-01-01

    Analysis of radiative decay of 1 P 1 → 1 S 0 + γ charmonium within sum rules of quantum chromodynamics was conducted. The sum rule, taking account of gluon exponential correction, was obtained, and width of Χ → η c + γ decay was calculated

  3. D-FLER - A Distributed Fuzzy Logic Engine for Rule-Based Wireless Sensor Networks

    NARCIS (Netherlands)

    Marin Perianu, Mihai; Havinga, Paul J.M.

    2007-01-01

    We propose D-FLER, a distributed, general-purpose reasoning engine for WSN. D-FLER uses fuzzy logic for fusing individual and neighborhood observations, in order to produce a more accurate and reliable result. Thorough simulation, we evaluate D-FLER in a fire-detection scenario, using both fire and

  4. D-FLER: A Distributed Fuzzy Logic Engine for Rule-based Wireless Sensor Networks

    NARCIS (Netherlands)

    Marin Perianu, Mihai; Havinga, Paul J.M.

    2007-01-01

    We propose D-FLER, a distributed, general-purpose reasoning engine for WSN. D-FLER uses fuzzy logic for fusing individual and neighborhood observations, in order to produce a more accurate and reliable result. Thorough simulation, we evaluate D-FLER in a fire-detection scenario, using both fire and

  5. Final Rule for Nonconformance Penalties for On-Highway Heavy-Duty Diesel Engines

    Science.gov (United States)

    EPA is taking final action to establish nonconformance penalties (NCPs) for manufacturers of heavy heavy-duty diesel engines (HHDDE) in model years 2012 and later for emissions of oxides of nitrogen (NOX) because we have found the criteria for NCPs.

  6. Selection rule engineering of forbidden transitions of a hydrogen atom near a nanogap

    Science.gov (United States)

    Kim, Hyunyoung Y.; Kim, Daisik S.

    2018-01-01

    We perform an analytical study on the allowance of forbidden transitions for a hydrogen atom placed near line dipole sources, mimicking light emanating from a one-dimensional metallic nanogap. It is shown that the rapid variation of the electric field vector, inevitable in the near zone, completely breaks the selection rule of Δl=±1. While the forbidden transitions between spherically symmetric S states, such as 2S to 1S or 3S to 1S (Δl=0), are rather robust against selection rule breakage, Δl=±2 transitions such as between 3D and 1S or 3D and 2S states are very vulnerable to the spatial variation of the perturbing electric field. Transitions between 2S and 3D states are enhanced by many orders of magnitude, aided by the quadratic nature of both the perturbing Hamiltonian and D wavefunctions. The forbidden dipole moment, which approaches one Bohr radius times the electric charge in the vicinity of the gap, can be written in a simple closed form owing to the one-dimensional nature of our gap. With large enough effective volume together with the symmetric nature of the excited state wavefunctions, our work paves way towards atomic physics application of infinitely long nanogaps.

  7. Automated concept-level information extraction to reduce the need for custom software and rules development.

    Science.gov (United States)

    D'Avolio, Leonard W; Nguyen, Thien M; Goryachev, Sergey; Fiore, Louis D

    2011-01-01

    Despite at least 40 years of promising empirical performance, very few clinical natural language processing (NLP) or information extraction systems currently contribute to medical science or care. The authors address this gap by reducing the need for custom software and rules development with a graphical user interface-driven, highly generalizable approach to concept-level retrieval. A 'learn by example' approach combines features derived from open-source NLP pipelines with open-source machine learning classifiers to automatically and iteratively evaluate top-performing configurations. The Fourth i2b2/VA Shared Task Challenge's concept extraction task provided the data sets and metrics used to evaluate performance. Top F-measure scores for each of the tasks were medical problems (0.83), treatments (0.82), and tests (0.83). Recall lagged precision in all experiments. Precision was near or above 0.90 in all tasks. Discussion With no customization for the tasks and less than 5 min of end-user time to configure and launch each experiment, the average F-measure was 0.83, one point behind the mean F-measure of the 22 entrants in the competition. Strong precision scores indicate the potential of applying the approach for more specific clinical information extraction tasks. There was not one best configuration, supporting an iterative approach to model creation. Acceptable levels of performance can be achieved using fully automated and generalizable approaches to concept-level information extraction. The described implementation and related documentation is available for download.

  8. Performance of engineered barriers for low-level waste

    International Nuclear Information System (INIS)

    Taplin, D.; Claridge, F.B.

    1987-09-01

    Geotechnical Resources Ltd., in association with Komex Consultants Ltd., was retained to collect, synthesize and evaluate the available information on the long term performance of engineered barriers for low-level radioactive wastes disposed in Canada. Literature was researched from Canadian, United States and European sources. A variety of barrier materials were assessed in the study and included natural clays, concrete and cement, metals, bentonite-sand admixes, bitumen and bituminous admixes, soil cement and polymeric membranes. The generalized geological and geotechnical conditions encountered within the soil and rock host media currently under consideration for disposal sites in southern Ontario were also summarized. Both internal barriers, or buffers, to immobilize the waste material and reduce radionuclide mobility, as well as external barriers to limit the migration of contaminants were examined. Microbial activities within the waste forms were analyzed, including cellulose degradation, methanogenesis and bicarbonate and organic reactions. Microbial interactions with the various engineered barrier materials under consideration were also assessed. Finally, the anticipated long term performances of the respective barrier materials under consideration were evaluated, along with the general suitability of the geological host media being proposed for disposal sites

  9. Engineered sorbent barriers for low-level waste disposal

    International Nuclear Information System (INIS)

    Mitchell, S.J.; Freeman, H.D.; Buelt, J.L.

    1987-01-01

    The Engineered Sorbent Barriers Program at Pacific Northwest Laboratory is developing sorbent materials to prevent the migration of radionuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Screening studies identified promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite of clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent, adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt%), activated charcoal (6 wt%), synthetic zeolite (20 wt%), and soil (73 wt%) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 2 references, 6 figures, 3 tables

  10. Engineered sorbent barriers for low-level waste disposal.

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Mitchell, S.J.; Buelt, J.L.

    1986-12-01

    The Engineered Sorbent Barriers Program at Pacific Northwest Laboratory is investigating sorbent materials to prevent the migration of soluble radio nuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Laboratory studies identifield promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite or clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent and was adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt%), activated charcoal (6 wt%), synthetic zeolite (20 wt%), and local soil (73 wt%) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow-land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 7 refs., 14 figs., 12 tabs.

  11. Engineered sorbent barriers for low-level waste disposal

    International Nuclear Information System (INIS)

    Freeman, H.D.; Mitchell, S.J.; Buelt, J.L.

    1986-12-01

    The Engineered Sorbent Barriers Program at Pacific Northwest Laboratory is investigating sorbent materials to prevent the migration of soluble radio nuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Laboratory studies identifield promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite or clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent and was adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt%), activated charcoal (6 wt%), synthetic zeolite (20 wt%), and local soil (73 wt%) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow-land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 7 refs., 14 figs., 12 tabs

  12. ML-Space: Hybrid Spatial Gillespie and Particle Simulation of Multi-Level Rule-Based Models in Cell Biology.

    Science.gov (United States)

    Bittig, Arne T; Uhrmacher, Adelinde M

    2017-01-01

    Spatio-temporal dynamics of cellular processes can be simulated at different levels of detail, from (deterministic) partial differential equations via the spatial Stochastic Simulation algorithm to tracking Brownian trajectories of individual particles. We present a spatial simulation approach for multi-level rule-based models, which includes dynamically hierarchically nested cellular compartments and entities. Our approach ML-Space combines discrete compartmental dynamics, stochastic spatial approaches in discrete space, and particles moving in continuous space. The rule-based specification language of ML-Space supports concise and compact descriptions of models and to adapt the spatial resolution of models easily.

  13. Context-Based Tourism Information Filtering with a Semantic Rule Engine

    Science.gov (United States)

    Lamsfus, Carlos; Martin, David; Alzua-Sorzabal, Aurkene; López-de-Ipiña, Diego; Torres-Manzanera, Emilio

    2012-01-01

    This paper presents the CONCERT framework, a push/filter information consumption paradigm, based on a rule-based semantic contextual information system for tourism. CONCERT suggests a specific insight of the notion of context from a human mobility perspective. It focuses on the particular characteristics and requirements of travellers and addresses the drawbacks found in other approaches. Additionally, CONCERT suggests the use of digital broadcasting as push communication technology, whereby tourism information is disseminated to mobile devices. This information is then automatically filtered by a network of ontologies and offered to tourists on the screen. The results obtained in the experiments carried out show evidence that the information disseminated through digital broadcasting can be manipulated by the network of ontologies, providing contextualized information that produces user satisfaction. PMID:22778584

  14. Benefiting from deep-level diversity : How congruence between knowledge and decision rules improves team decision making and team perceptions

    NARCIS (Netherlands)

    Rink, Floor; Ellemers, Naomi

    In two experiments we show how teams can benefit from the presence of multiple sources of deep-level task-related diversity. We manipulated differences (vs. similarities) in task information and personal decision rules in dyads (Study 1) and three-person teams (Study 2). The results indicate that

  15. Conformity to Parental Rules : Asymmetric Influences of Father’s and Mother’s Levels of Education

    NARCIS (Netherlands)

    Slik, Frans W.P. van der; Graaf, Nan Dirk de; Gerris, Jan R.M.

    2002-01-01

    The relative e¡ects of both parents’educational levels on their child-rearing values were examined by analysing data froma sample of Dutch families (N¼589).This research focuses upon dominance of fathers overmothers with respect to the value placed on children’s conformity to parental rules.We argue

  16. Civil engineering work to raise the level of Route Goward

    CERN Multimedia

    2013-01-01

    Civil engineering work to raise the level of Route Goward will take place during Long Shutdown 1. The work will begin on 18 March 2013 and is expected to last around 5 months.   Route Goward runs over the top of the PS tunnel and is the only access route to the inside of the ring. The layer of shielding backfill beneath this road is the thinnest anywhere on the PS ring. As the purpose of this shielding is to protect against the ionising radiation emitted by the accelerator when in operation, this road has been classified as a “supervised radiation area” according to radiation protection regulations. This classification was merely a temporary solution and, on the recommendation of the PS Radiation Working Group (PSRWG), the decision has been taken to raise the surface level permanently by around 2 m in order to increase the thickness of the shielding and thus lower the dose rate to that of a non-designated area. As the PS tunnel itself is unable to withstand the weight of t...

  17. Collaboration rules.

    Science.gov (United States)

    Evans, Philip; Wolf, Bob

    2005-01-01

    Corporate leaders seeking to boost growth, learning, and innovation may find the answer in a surprising place: the Linux open-source software community. Linux is developed by an essentially volunteer, self-organizing community of thousands of programmers. Most leaders would sell their grandmothers for workforces that collaborate as efficiently, frictionlessly, and creatively as the self-styled Linux hackers. But Linux is software, and software is hardly a model for mainstream business. The authors have, nonetheless, found surprising parallels between the anarchistic, caffeinated, hirsute world of Linux hackers and the disciplined, tea-sipping, clean-cut world of Toyota engineering. Specifically, Toyota and Linux operate by rules that blend the self-organizing advantages of markets with the low transaction costs of hierarchies. In place of markets' cash and contracts and hierarchies' authority are rules about how individuals and groups work together (with rigorous discipline); how they communicate (widely and with granularity); and how leaders guide them toward a common goal (through example). Those rules, augmented by simple communication technologies and a lack of legal barriers to sharing information, create rich common knowledge, the ability to organize teams modularly, extraordinary motivation, and high levels of trust, which radically lowers transaction costs. Low transaction costs, in turn, make it profitable for organizations to perform more and smaller transactions--and so increase the pace and flexibility typical of high-performance organizations. Once the system achieves critical mass, it feeds on itself. The larger the system, the more broadly shared the knowledge, language, and work style. The greater individuals' reputational capital, the louder the applause and the stronger the motivation. The success of Linux is evidence of the power of that virtuous circle. Toyota's success is evidence that it is also powerful in conventional companies.

  18. Draft fracture mechanics code case for American Society of Mechanical Engineers NUPACK rules

    International Nuclear Information System (INIS)

    McConnell, P.; Sorenson, K.; Nickell, R.; Saegusa, T.

    2004-01-01

    The containment boundaries of most spent-fuel casks certified for use in the United States by the Nuclear Regulatory Commission are constructed with stainless steel, a material that is ductile in an engineering sense at all temperatures and for which, therefore, fracture mechanics principles are not relevant for the containment application. Ferritic materials may fail in a nonductile manner at sufficiently low temperatures, so fracture mechanics principles may be applied to preclude nonductile fracture. Because of the need to transport and store spent nuclear fuel safely in all types of climatic conditions, these vessels have regulatory lowest service temperatures that range down to -40 C (-40 F) for transport application. Such low service temperatures represent a severe challenge in terms of fracture toughness to many ferritic materials. Linear-elastic and elastic-plastic fracture mechanics principles provide a methodology for evaluating ferritic materials under such conditions

  19. Engineered sorbent barriers for low-level waste disposal

    International Nuclear Information System (INIS)

    Mitchell, S.J.; Freeman, H.D.; Buelt, J.L.

    1986-01-01

    Pacific Northwest Laboratory is developing sorbent materials to prevent the migration of radionuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Screening studies identified promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite or clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent, adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt %), activated charcoal (6 wt %), synthetic zeolite (20 wt %), and soil (73 wt %) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 2 refs., 6 figs., 3 tabs

  20. Teaching Engineering at First Degree Level in the UK.

    Science.gov (United States)

    Foster, Peter J.

    1999-01-01

    Presents an approach to the teaching of engineering that uses the ideas about the teaching of academic subject matter developed by D. Ausubel. Identifies a threat to higher education in the lack of knowledge of the relationship between research and teaching in engineering and science and remarks on the absence of a corpus of work related to…

  1. Students’ Learning Obstacles and Alternative Solution in Counting Rules Learning Levels Senior High School

    Directory of Open Access Journals (Sweden)

    M A Jatmiko

    2017-12-01

    Full Text Available The counting rules is a topic in mathematics senior high school. In the learning process, teachers often find students who have difficulties in learning this topic. Knowing the characteristics of students' learning difficulties and analyzing the causes is important for the teacher, as an effort in trying to reflect the learning process and as a reference in constructing alternative learning solutions which appropriate to anticipate students’ learning obstacles. This study uses qualitative methods and involves 70 students of class XII as research subjects. The data collection techniques used in this study is diagnostic test instrument about learning difficulties in counting rules, observation, and interview. The data used to know the learning difficulties experienced by students, the causes of learning difficulties, and to develop alternative learning solutions. From the results of data analysis, the results of diagnostic tests researcher found some obstacles faced by students, such as students get confused in describing the definition, students difficulties in understanding the procedure of solving multiplication rules. Based on those problems, researcher analyzed the causes of these difficulties and make hypothetical learning trajectory as an alternative solution in counting rules learning.

  2. Application of Adjusted Canonical Correlation Analysis (ACCA) to study the association between mathematics in Level 1 and Level 2 and performance of engineering disciplines in Level 2

    Science.gov (United States)

    Peiris, T. S. G.; Nanayakkara, K. A. D. S. A.

    2017-09-01

    Mathematics plays a key role in engineering sciences as it assists to develop the intellectual maturity and analytical thinking of engineering students and exploring the student academic performance has received great attention recently. The lack of control over covariates motivates the need for their adjustment when measuring the degree of association between two sets of variables in Canonical Correlation Analysis (CCA). Thus to examine the individual effects of mathematics in Level 1 and Level 2 on engineering performance in Level 2, two adjusted analyses in CCA: Part CCA and Partial CCA were applied for the raw marks of engineering undergraduates for three different disciplines, at the Faculty of Engineering, University of Moratuwa, Sri Lanka. The joint influence of mathematics in Level 1 and Level 2 is significant on engineering performance in Level 2 irrespective of the engineering disciplines. The individual effect of mathematics in Level 2 is significantly higher compared to the individual effect of mathematics in Level 1 on engineering performance in Level 2. Furthermore, the individual effect of mathematics in Level 1 can be negligible. But, there would be a notable indirect effect of mathematics in Level 1 on engineering performance in Level 2. It can be concluded that the joint effect of mathematics in both Level 1 and Level 2 is immensely beneficial to improve the overall academic performance at the end of Level 2 of the engineering students. Furthermore, it was found that the impact mathematics varies among engineering disciplines. As partial CCA and partial CCA are not widely explored in applied work, it is recommended to use these techniques for various applications.

  3. Idaho National Engineering Laboratory High-Level Waste Roadmap

    International Nuclear Information System (INIS)

    1993-08-01

    The Idaho National Engineering Laboratory (INEL) High-Level Waste (HLW) Roadmap takes a strategic look at the entire HLW life-cycle starting with generation, through interim storage, treatment and processing, transportation, and on to final disposal. The roadmap is an issue-based planning approach that compares ''where we are now'' to ''where we want and need to be.'' The INEL has been effectively managing HLW for the last 30 years. Calcining operations are continuing to turn liquid HLW into a more manageable form. Although this document recognizes problems concerning HLW at the INEL, there is no imminent risk to the public or environment. By analyzing the INEL current business operations, pertinent laws and regulations, and committed milestones, the INEL HLW Roadmap has identified eight key issues existing at the INEL that must be resolved in order to reach long-term objectives. These issues are as follows: A. The US Department of Energy (DOE) needs a consistent policy for HLW generation, handling, treatment, storage, and disposal. B. The capability for final disposal of HLW does not exist. C. Adequate processes have not been developed or implemented for immobilization and disposal of INEL HLW. D. HLW storage at the INEL is not adequate in terms of capacity and regulatory requirements. E. Waste streams are generated with limited consideration for waste minimization. F. HLW is not adequately characterized for disposal nor, in some cases, for storage. G. Research and development of all process options for INEL HLW treatment and disposal are not being adequately pursued due to resource limitations. H. HLW transportation methods are not selected or implemented. A root-cause analysis uncovered the underlying causes of each of these issues

  4. A Rule-Based Policy-Level Model of Nonsuperpower Behavior in Strategic Conflicts.

    Science.gov (United States)

    1982-12-01

    a mechanism. The human mind tends to work linearly and to focus implicitly on a few variables. Experience results in subconscious models with far...which is slower. Alternatives to the current ROSIE implementation include reprogramming Scenario Agent in the C language (the language used for the Red...perception, opportunity perception, opportunity response, and assertiveness. As rules are refined, maintenance and reprogramming of the model will be required

  5. An approach for environmental risk assessment of engineered nanomaterials using Analytical Hierarchy Process (AHP) and fuzzy inference rules.

    Science.gov (United States)

    Topuz, Emel; van Gestel, Cornelis A M

    2016-01-01

    The usage of Engineered Nanoparticles (ENPs) in consumer products is relatively new and there is a need to conduct environmental risk assessment (ERA) to evaluate their impacts on the environment. However, alternative approaches are required for ERA of ENPs because of the huge gap in data and knowledge compared to conventional pollutants and their unique properties that make it difficult to apply existing approaches. This study aims to propose an ERA approach for ENPs by integrating Analytical Hierarchy Process (AHP) and fuzzy inference models which provide a systematic evaluation of risk factors and reducing uncertainty about the data and information, respectively. Risk is assumed to be the combination of occurrence likelihood, exposure potential and toxic effects in the environment. A hierarchy was established to evaluate the sub factors of these components. Evaluation was made with fuzzy numbers to reduce uncertainty and incorporate the expert judgements. Overall score of each component was combined with fuzzy inference rules by using expert judgements. Proposed approach reports the risk class and its membership degree such as Minor (0.7). Therefore, results are precise and helpful to determine the risk management strategies. Moreover, priority weights calculated by comparing the risk factors based on their importance for the risk enable users to understand which factor is effective on the risk. Proposed approach was applied for Ag (two nanoparticles with different coating) and TiO2 nanoparticles for different case studies. Results verified the proposed benefits of the approach. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Investigating impact of motor oil quality on vehicles engine induced noise level

    Directory of Open Access Journals (Sweden)

    I. Arefian

    2015-09-01

    Full Text Available Introduction: Vehicle engine id one of the main sources of noise which its level is influenced by various parameters. The aim of this study was to investigate the impact of motor oils quality before and after oil change on the variability of vehicle engine induced noise level. In this study it is tried to follow-up the efficacy of motor oil quality on engines sound level. Material and Method: First, engine noise of 94 vehicles were recorded for 30 seconds before and after oil change and all the vehicles technical information including mileage, type of motor oil, and type of vehicle were registered. Following, the recorded noises were calibrated in semi-anechoic chamber and the sound pressure levels were measured with A and C-weighting network and main octav bands, using a sound level meters. The obtained results analyzed using SPSS software version 17. Results: The effects of motor oil quality on different noise levels of engines were determined and a significant reduction in noise level of vehicles engine was observed. Investigation of the relationship between mileage and motor oil quality on various engines sound level manifested that vehicles with mileage ranged 100000-150000 miles had significant reduction in their sound pressure levels in comparison with other vehicles. Conclusion: The results revealed that engine oil is among factors reducing the vehicle engine induced noise level. Moreover, the engine oil type and the vehicle mileage are key variables which determine the impact of engine oil quality on reduction of the sound level of vehicles engine.

  7. Real-time Geographic Information System (GIS) for Monitoring the Area of Potential Water Level Using Rule Based System

    Science.gov (United States)

    Anugrah, Wirdah; Suryono; Suseno, Jatmiko Endro

    2018-02-01

    Management of water resources based on Geographic Information System can provide substantial benefits to water availability settings. Monitoring the potential water level is needed in the development sector, agriculture, energy and others. In this research is developed water resource information system using real-time Geographic Information System concept for monitoring the potential water level of web based area by applying rule based system method. GIS consists of hardware, software, and database. Based on the web-based GIS architecture, this study uses a set of computer that are connected to the network, run on the Apache web server and PHP programming language using MySQL database. The Ultrasound Wireless Sensor System is used as a water level data input. It also includes time and geographic location information. This GIS maps the five sensor locations. GIS is processed through a rule based system to determine the level of potential water level of the area. Water level monitoring information result can be displayed on thematic maps by overlaying more than one layer, and also generating information in the form of tables from the database, as well as graphs are based on the timing of events and the water level values.

  8. Engineering yeast for high-level production of stilbenoid antioxidants

    DEFF Research Database (Denmark)

    Li, Mingji; Schneider, Konstantin; Kristensen, Mette

    2016-01-01

    engineered the yeast Saccharomyces cerevisiae for production of stilbenoids on a simple mineral medium typically used for industrial production. We applied a pull-push-block strain engineering strategy that included overexpression of the resveratrol biosynthesis pathway, optimization of the electron transfer...... to the cytochrome P450 monooxygenase, increase of the precursors supply, and decrease of the pathway intermediates degradation. Fed-batch fermentation of the final strain resulted in a final titer of 800 mg l(-1) resveratrol, which is by far the highest titer reported to date for production of resveratrol from...

  9. Occupational exposure to diesel engine exhaust and serum cytokine levels

    NARCIS (Netherlands)

    Dai, Yufei; Ren, Dianzhi; Bassig, Bryan A.; Vermeulen, Roel; Hu, Wei; Niu, Yong; Duan, Huawei; Ye, Meng; Meng, Tao; Xu, Jun; Li, Ping; Shen, Meili; Yang, Jufang; Fu, Wei; Meliefste, Kees; Silverman, Debra T.; Rothman, Nathaniel; Lan, Qing; Zheng, Yuxin

    The International Agency for Research on Cancer has classified diesel engine exhaust (DEE) as a human lung carcinogen. Given that inflammation is suspected to be an important underlying mechanism of lung carcinogenesis, we evaluated the relationship between DEE exposure and the inflammatory response

  10. History and Benefits of Engine Level Testing Throughout the Space Shuttle Main Engine Program

    Science.gov (United States)

    VanHooser, Katherine; Kan, Kenneth; Maddux, Lewis; Runkle, Everett

    2010-01-01

    Rocket engine testing is important throughout a program s life and is essential to the overall success of the program. Space Shuttle Main Engine (SSME) testing can be divided into three phases: development, certification, and operational. Development tests are conducted on the basic design and are used to develop safe start and shutdown transients and to demonstrate mainstage operation. This phase helps form the foundation of the program, demands navigation of a very steep learning curve, and yields results that shape the final engine design. Certification testing involves multiple engine samples and more aggressive test profiles that explore the boundaries of the engine to vehicle interface requirements. The hardware being tested may have evolved slightly from that in the development phase. Operational testing is conducted with mature hardware and includes acceptance testing of flight assets, resolving anomalies that occur in flight, continuing to expand the performance envelope, and implementing design upgrades. This paper will examine these phases of testing and their importance to the SSME program. Examples of tests conducted in each phase will also be presented.

  11. Crossing rule for a PT-symmetric two-level time-periodic system

    International Nuclear Information System (INIS)

    Moiseyev, Nimrod

    2011-01-01

    For a two-level system in a time-periodic field we show that in the non-Hermitian PT case the level crossing is of two quasistationary states that have the same dynamical symmetry property. At the field's parameters where the two levels which have the same dynamical symmetry cross, the corresponding quasienergy states coalesce and a self-orthogonal state is obtained. This situation is very different from the Hermitian case where a crossing of two quasienergy levels happens only when the corresponding two quasistationary states have different dynamical symmetry properties and, unlike the situation in the non-Hermitian case, the spectrum remains complete also when the two levels cross.

  12. When global rule reversal meets local task switching: The neural mechanisms of coordinated behavioral adaptation to instructed multi-level demand changes.

    Science.gov (United States)

    Shi, Yiquan; Wolfensteller, Uta; Schubert, Torsten; Ruge, Hannes

    2018-02-01

    Cognitive flexibility is essential to cope with changing task demands and often it is necessary to adapt to combined changes in a coordinated manner. The present fMRI study examined how the brain implements such multi-level adaptation processes. Specifically, on a "local," hierarchically lower level, switching between two tasks was required across trials while the rules of each task remained unchanged for blocks of trials. On a "global" level regarding blocks of twelve trials, the task rules could reverse or remain the same. The current task was cued at the start of each trial while the current task rules were instructed before the start of a new block. We found that partly overlapping and partly segregated neural networks play different roles when coping with the combination of global rule reversal and local task switching. The fronto-parietal control network (FPN) supported the encoding of reversed rules at the time of explicit rule instruction. The same regions subsequently supported local task switching processes during actual implementation trials, irrespective of rule reversal condition. By contrast, a cortico-striatal network (CSN) including supplementary motor area and putamen was increasingly engaged across implementation trials and more so for rule reversal than for nonreversal blocks, irrespective of task switching condition. Together, these findings suggest that the brain accomplishes the coordinated adaptation to multi-level demand changes by distributing processing resources either across time (FPN for reversed rule encoding and later for task switching) or across regions (CSN for reversed rule implementation and FPN for concurrent task switching). © 2017 Wiley Periodicals, Inc.

  13. Final Rule for Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

    Science.gov (United States)

    EPA adopted emission standards and related provisions for aircraft gas turbine engines with rated thrusts greater than 26.7 kilonewtons. These engines are used primarily on commercial passenger and freight aircraft.

  14. Low level waste management at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Rodgers, A.D.; Truitt, D.J.; Logan, J.A.; Brown, R.M.

    1986-02-01

    EG and G Idaho, Inc. is the lead contractor for the Department of Energy (DOE) National Low Level Waste Management Program, established in 1979. In this role, the company uses its waste management expertise to provide management and technical direction to support the disposal of low-level waste (LLW) in a manner that protects the environment and the public health and safety while improving efficiency and cost-effectiveness. Program activities are divided into two areas: defense-related and commercial nuclear reactor programs. The defense program was established to develop technology improvements, provide technology transfer, and to ensure a more efficient and uniform system for low level waste disposal. To achieve the program's goals, it is necessary to improve, document, and, where necessary, develop new methods for waste generation reduction, waste treatment, shallow-land burial, greater confinement disposal, and measures to correct existing site deficiencies. The commercial low level waste management program provides support to assist the states in developing an effective national low level waste management system and provides technical assistance for siting of regional commercial LLW disposal sites. The program provides technical and informational support to state officials, low level waste generators, managers, and facility operators to resolve low level waste problems and to improve the systems' overall effectiveness. Procedures are developed and documented and made available to commercial users through this program. Additional work is being conducted to demonstrate the stabilization and closure of low level radioactive waste disposal sites and develop the criteria and procedures for acceptance of such sites by the Department of Energy after closure has been completed. 7 refs., 6 figs., 1 tab

  15. Optimum Safety Levels and Design Rules for the Icelandic Type Berm Breakwater

    DEFF Research Database (Denmark)

    Sigurdarson, Sigurdur; van der Meer, Jentsje W.; Burcharth, Hans F.

    2007-01-01

    Guidance on selection of breakwater types and related design safety levels for breakwaters are almost non-existent, which is the reason that PIANC has initiated working group 47 on this subject. This paper presents ongoing work particulary on the Icelandic type berm breakwater within the PIANC...... working group. It will concentrate on design guidance and on the optimum safety levels for this type of structure....

  16. Direct Final Rule for Control of Air Pollution From Aircraft and Aircraft Engines; Emission Standards and Test Procedures

    Science.gov (United States)

    This rule will adopt the current voluntary NOx and CO emissions standards of the United Nations International Civil Aviation Organization (ICAO), bringing the United States aircraft standards into alignment with the international standards.

  17. Simulating the effects of turbocharging on the emission levels of a gasoline engine

    Directory of Open Access Journals (Sweden)

    Amir Reza Mahmoudi

    2017-12-01

    Full Text Available The main objective of this work was to respond to the global concern for the rise of the emissions and the necessity of preventing them to form rather than dealing with their after-effects. Therefore, the production levels of four main emissions, namely NOx, CO2, CO and UHC in gasoline engine of Nissan Maxima 1994 is assessed via 1-D simulation with the GT-Power code. Then, a proper matching of turbine-compressor is carried out to propose a turbocharger for the engine, and the resultant emissions are compared to the naturally aspirated engine. It is found that the emission levels of NOx, CO, and CO2 are higher in terms of their concentration in the exhaust fume of the turbocharged engine, in comparison with the naturally aspirated engine. However, at the same time, the brake power and the brake specific emissions produced by the turbocharged engine are respectively higher and lower than those of the naturally aspirated engine. Therefore, it is concluded that, for a specific application, turbocharging provides the chance to achieve the performance of a potential naturally aspirated engine while producing lower emissions. Keywords: Emission, Gasoline SI engine, Turbocharging, GT-Power, 1-D simulation, Brake specific

  18. Optimum Safety Levels and Design Rules for the Icelandic-Type Berm Breakwater

    DEFF Research Database (Denmark)

    Sigurdarson, Sigurdur; van der Meer, Jentsje W.; Burcharth, Hans F.

    2009-01-01

    strategies and possible failure with corresponding downtime have been taken into account, as well as actual market prices (in Iceland and Norway) for rack material and construction. Calculations show that low stability numbers for the largest rock armour layer give the optimal safety level....

  19. High-Level Waste Salt Disposition Systems Engineering Team Final Report, Volumes I, II, and III

    International Nuclear Information System (INIS)

    Piccolo, S.F.

    1999-01-01

    This report describes the process used and results obtained by the High Level Waste Salt Disposition Systems Engineering Team to select a primary and backup alternative salt disposition method for the Savannah River Site

  20. Level density approach to perturbation theory and inverse-energy-weighted sum-rules

    International Nuclear Information System (INIS)

    Halemane, T.R.

    1983-01-01

    The terms in the familiar Rayleigh-Schroedinger perturbation series involve eigenvalues and eigenfunctions of the unperturbed operator. A level density formalism, that does not involve computation of eigenvalues and eigenfunctions, is given here for the perturbation series. In the CLT (central limit theorem) limit the expressions take very simple linear forms. The evaluation is in terms of moments and traces of operators and operator products. 3 references

  1. PSOLA: A Heuristic Land-Use Allocation Model Using Patch-Level Operations and Knowledge-Informed Rules.

    Directory of Open Access Journals (Sweden)

    Yaolin Liu

    Full Text Available Optimizing land-use allocation is important to regional sustainable development, as it promotes the social equality of public services, increases the economic benefits of land-use activities, and reduces the ecological risk of land-use planning. Most land-use optimization models allocate land-use using cell-level operations that fragment land-use patches. These models do not cooperate well with land-use planning knowledge, leading to irrational land-use patterns. This study focuses on building a heuristic land-use allocation model (PSOLA using particle swarm optimization. The model allocates land-use with patch-level operations to avoid fragmentation. The patch-level operations include a patch-edge operator, a patch-size operator, and a patch-compactness operator that constrain the size and shape of land-use patches. The model is also integrated with knowledge-informed rules to provide auxiliary knowledge of land-use planning during optimization. The knowledge-informed rules consist of suitability, accessibility, land use policy, and stakeholders' preference. To validate the PSOLA model, a case study was performed in Gaoqiao Town in Zhejiang Province, China. The results demonstrate that the PSOLA model outperforms a basic PSO (Particle Swarm Optimization in the terms of the social, economic, ecological, and overall benefits by 3.60%, 7.10%, 1.53% and 4.06%, respectively, which confirms the effectiveness of our improvements. Furthermore, the model has an open architecture, enabling its extension as a generic tool to support decision making in land-use planning.

  2. Developing Curriculum of Nuclear Civil Engineering Degree Programme at Graduate Level

    International Nuclear Information System (INIS)

    Iqbal, J.

    2016-01-01

    Full text: The paper suggests the introduction of a new degree, namely nuclear civil engineering at graduate level for better utilization of civil engineers in nuclear power plant (NPP) design and construction. At present, both nuclear engineering and civil engineering degrees are offered at undergraduate and graduate levels in numerous renowned universities of the world. However, when a civil engineer, even after completion of nuclear engineering at postgraduate level, undertakes an assignment related to NPP design, he comes across various problems which are not covered in the present curricula. For instance, NPPs’ siting issues, design of pre-stressed concrete containment against loads of loss of coolant accident (LOCA), various impulsive and impactive loads (e.g., detonations, aircraft crash analysis, etc.) and shielding calculations are some of the core issues during nuclear power plant design. The paper highlights the importance of introduction of nuclear civil engineering degree at the graduate level. Besides, the contents of the proposed course work have also been discussed. Keeping in view the fact that, currently, no such degree is offered in any university of the world, the paper explores useful avenues to human resource development for introducing and expanding nuclear power programmes. (author

  3. Effectiveness of UK and International A-Level Assessment in Predicting Performance in Engineering

    Science.gov (United States)

    Birch, David M.; Rienties, Bart

    2014-01-01

    In many universities, admissions decisions are made based upon the advanced-level (A-Level) results. The purpose of this study was to assess the value of A-level and international equivalents as a predictor of early achievement in higher education. About 135 UK and 92 international undergraduate engineering students from 35 countries were assessed…

  4. Fair rules for siting a high-level nuclear waste repository

    International Nuclear Information System (INIS)

    Easterling, D.

    1992-01-01

    Geologic repositories are designed to resolve the ever-growing problem of high-level nuclear waste, but these facilities invite intense local opposition due to the perceived severity of the risks and the possibility of stigma effects. This analysis examines whether the perceived fairness of the siting process affects local residents' support for hosting a repository. In particular, a survey of 1,001 Nevada residents is used to test the hypothesis that an individual's willingness to accept a local repository will increase if he or she is convinced that this is the safest disposal option available. A logistic analysis indicates that beliefs regarding relative suitability have an independent effect on the acceptability of a local repository (i.e., Yucca Mountain). The article then considers the question of how to implement an optimizing strategy for siting facilities, comparing an idealized strategy against the original Nuclear Waste Policy Act (NWPA) of 1982 and the Amendments Act of 1987. Although choosing the safest site seems as if it could enhance public acceptance of the repository program, there is currently little prospect of identifying the best option to the high-level waste problem and, as a results, little chance of gaining the public support that is necessary to promote a successful siting outcome. 81 refs., 1 fig., 5 tabs

  5. Exploiting deterministic maintenance opportunity windows created by conservative engineering design rules that result in free time locked into large high-speed coupled production lines with finite buffers

    Directory of Open Access Journals (Sweden)

    Durandt, Casper

    2016-08-01

    Full Text Available Conservative engineering design rules for large serial coupled production processes result in machines having locked-in free time (also called ‘critical downtime’ or ‘maintenance opportunity windows’, which cause idle time if not used. Operators are not able to assess a large production process holistically, and so may not be aware that they form the current bottleneck – or that they have free time available due to interruptions elsewhere. A real-time method is developed to accurately calculate and display free time in location and magnitude, and efficiency improvements are demonstrated in large-scale production runs.

  6. Game mechanics engine

    OpenAIRE

    Magnusson, Lars V

    2011-01-01

    Game logic and game rules exists in all computer games, but they are created di erently for all game engines. This game engine dependency exists because of how the internal object model is implemented in the engine, as a place where game logic data is intermingled with the data needed by the low- level subsystems. This thesis propose a game object model design, based on existing theory, that removes this dependency and establish a general game logic framework. The thesis the...

  7. Rules for biocatalyst and reaction engineering to implement effective, NAD(P)H-dependent, whole cell bioreductions

    DEFF Research Database (Denmark)

    Kratzer, Regina; Woodley, John; Nidetzky, Bernd

    2015-01-01

    recycling mode and reaction conditions represent design options that strongly affect bioreduction efficiency. In this paper, each option was critically scrutinized and decision rules formulated based on well-described literature examples. The development chain was visualized as a decision-tree that can...

  8. Ruling by canal: Governance and system-level design characteristics of large scale irrigation infrastructure in India and Uzbekistan

    Directory of Open Access Journals (Sweden)

    Peter Mollinga

    2016-06-01

    Full Text Available This paper explores the relationship between governance regime and large-scale irrigation system design by investigating three cases: 1 protective irrigation design in post-independent South India; 2 canal irrigation system design in Khorezm Province, Uzbekistan, as implemented in the USSR period, and 3 canal design by the Madras Irrigation and Canal Company, as part of an experiment to do canal irrigation development in colonial India on commercial terms in the 1850s-1860s. The mutual shaping of irrigation infrastructure design characteristics on the one hand and management requirements and conditions on the other has been documented primarily at lower, within-system levels of the irrigation systems, notably at the level of division structures. Taking a 'social construction of technology' perspective, the paper analyses the relationship between technological structures and management and governance arrangements at irrigation system level. The paper finds qualitative differences in the infrastructural configuration of the three irrigation systems expressing and facilitating particular forms of governance and rule, differences that matter for management and use, and their effects and impacts.

  9. Requirements for High Level Models Supporting Design Space Exploration in Model-based Systems Engineering

    OpenAIRE

    Haveman, Steven P.; Bonnema, G. Maarten

    2013-01-01

    Most formal models are used in detailed design and focus on a single domain. Few effective approaches exist that can effectively tie these lower level models to a high level system model during design space exploration. This complicates the validation of high level system requirements during detailed design. In this paper, we define requirements for a high level model that is firstly driven by key systems engineering challenges present in industry and secondly connects to several formal and d...

  10. Final Rule for Control of Air Pollution from Aircraft and Aircraft Engines: Emission Standards and Test Procedures

    Science.gov (United States)

    EPA is amending the existing emission standards for oxides of nitrogen (NOx) for new commercial aircraft engines. These standards are equivalent to the NOx emission standards of the United Nations International Civil Aviation Organization (ICAO).

  11. Integrated System-Level Optimization for Concurrent Engineering With Parametric Subsystem Modeling

    Science.gov (United States)

    Schuman, Todd; DeWeck, Oliver L.; Sobieski, Jaroslaw

    2005-01-01

    The introduction of concurrent design practices to the aerospace industry has greatly increased the productivity of engineers and teams during design sessions as demonstrated by JPL's Team X. Simultaneously, advances in computing power have given rise to a host of potent numerical optimization methods capable of solving complex multidisciplinary optimization problems containing hundreds of variables, constraints, and governing equations. Unfortunately, such methods are tedious to set up and require significant amounts of time and processor power to execute, thus making them unsuitable for rapid concurrent engineering use. This paper proposes a framework for Integration of System-Level Optimization with Concurrent Engineering (ISLOCE). It uses parametric neural-network approximations of the subsystem models. These approximations are then linked to a system-level optimizer that is capable of reaching a solution quickly due to the reduced complexity of the approximations. The integration structure is described in detail and applied to the multiobjective design of a simplified Space Shuttle external fuel tank model. Further, a comparison is made between the new framework and traditional concurrent engineering (without system optimization) through an experimental trial with two groups of engineers. Each method is evaluated in terms of optimizer accuracy, time to solution, and ease of use. The results suggest that system-level optimization, running as a background process during integrated concurrent engineering sessions, is potentially advantageous as long as it is judiciously implemented.

  12. Application of smart transmitter technology in nuclear engineering measurements with level detection algorithm

    International Nuclear Information System (INIS)

    Kang, Hyun Gook; Seong, Poong Hyun

    1994-01-01

    In this study a programmable smart transmitter is designed and applied to the nuclear engineering measurements. In order to apply the smart transmitter technology to nuclear engineering measurements, the water level detection function is developed and applied in this work. In the real time system, the application of level detection algorithm can make the operator of the nuclear power plant sense the water level more rapidly. Furthermore this work can simplify the data communication between the level-sensing thermocouples and the main signal processor because the level signal is determined at field. The water level detection function reduces the detection time to about 8.3 seconds by processing the signal which has the time constant 250 seconds and the heavy noise signal

  13. An approach for environmental risk assessment of engineered nanomaterials using Analytical Hierarchy Process (AHP) and fuzzy inference rules

    NARCIS (Netherlands)

    Topuz, E.; van Gestel, C.A.M.

    2016-01-01

    The usage of Engineered Nanoparticles (ENPs) in consumer products is relatively new and there is a need to conduct environmental risk assessment (ERA) to evaluate their impacts on the environment. However, alternative approaches are required for ERA of ENPs because of the huge gap in data and

  14. On the design of design processes in architecture and engineering : technological rules and the principle of minimal specification

    NARCIS (Netherlands)

    Aken, van J.E.

    2003-01-01

    As complexity and scale of design processes in architecture and in engineering increase, as well as the demands on these processes with respect to costs, throughput time and quality, traditional approaches to organise and plan these processes may no longer suffice. In this conceptual article it is

  15. Influences of engineered barrier systems on low-level radioactive waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Buckley, L. P.

    1987-09-15

    There are major differences between the current practices of shallow land burial and alternative concepts for the disposal of low-level radioactive wastes. Additional protection provided with engineered barrier systems can overcome major concerns the public has with shallow land burial: subsidence; percolating ground waters; radionuclide migration; and the vulnerability of shallow trenches to intrusion. The presence of a variety of engineered barriers to restrict water movement, retain radionuclides and to prevent plant animal or human intrusion leads to significant changes to input data for performance assessment models. Several programs which are underway to more accurately predict the long-term performance of engineered barriers for low-level waste will be described.

  16. Influences of engineered barrier systems on low-level radioactive waste disposal

    International Nuclear Information System (INIS)

    Buckley, L.P.

    1987-09-01

    There are major differences between the current practices of shallow land burial and alternative concepts for the disposal of low-level radioactive wastes. Additional protection provided with engineered barrier systems can overcome major concerns the public has with shallow land burial: subsidence; percolating ground waters; radionuclide migration; and the vulnerability of shallow trenches to intrusion. The presence of a variety of engineered barriers to restrict water movement, retain radionuclides and to prevent plant animal or human intrusion leads to significant changes to input data for performance assessment models. Several programs which are underway to more accurately predict the long-term performance of engineered barriers for low-level waste will be described

  17. Influence Of Aircraft Engine Exhaust Emissions At A Global Level And Preventive Measures

    Directory of Open Access Journals (Sweden)

    Jasna Golubić

    2004-07-01

    Full Text Available The work considers the differences in the aircraft engine exhaustemissions, as well as the impact of the emissions on theenvironment depending on several factors. These include theage of the engine, i. e. technical refinement, engine operating regimesat different thrusts during time periods: takeoff, climb,approach, etc. Also, the exhaust emissions do not have thesame influence on different atmospheric layers. The pollutantsemitted at higher altitudes during cruising have become agreater problem, although the volume of pollutants is smaller,due to the chemical complexity and sensitivity of these layers ascompared to the lower layers of atmosphere. One of the reasonswhy these problems have long remained outside the focus of interestof the environmentalists is that the air transport of goodsand people is performed at high altitudes, so that the pollutionof atmosphere does not present a direct threat to anyone, sincethe environment is being polluted at a global level and thereforeis more difficult to notice at the local level.

  18. Microbiopsy a first-level diagnostic test to rule out oral dysplasia or carcinoma in general dental practice.

    Science.gov (United States)

    Pentenero, M; Val, M; Rosso, S; Gandolfo, S

    2018-03-01

    Diagnostic delay in oral oncology could be improved if general dentists had a reliable and easy-to-use first-level diagnostic test to rule out the presence of oral dysplasia or carcinoma. Microbiopsy has been proved to have high sensitivity and high negative predictive value in a clinical setting characterized by high prevalence of disease. Moreover, it has been proved to be easily performed by general dentists. This study aimed to determine the negative predictive value of microbiopsy in routine dental practice: a clinical setting characterized by low prevalence of disease. Within the frame of a previous study, general dentists from the Metropolitan Area of Turin performed microbiopsy for each oral mucosal lesion detected during their practice. The clinical outcome of 129 lesions negative at microbiopsy was checked by a query performed through the database of the Piedmont Cancer Registry, covering the population of the Metropolitan Area of Turin, with particular reference to cancer involving the mouth (ICD-10:C03-06). This allowed us to define "true negative" cases and to calculate the negative predictive value of microbiopsy. In a mean follow-up of 7.5 years (range 7-9 years), with a dropout rate of 7.7%, no case of tumour involving the mouth was observed, thus revealing a negative predictive value approaching 100%. Microbiopsy represents an easy-to-use and reliable first-level test able to aid general dentists to select patients requiring an oral medicine assessment in a short time and definitely to avoid diagnostic delay in oncologically relevant oral mucosal lesions. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd. All rights reserved.

  19. Interestingness measures and strategies for mining multi-ontology multi-level association rules from gene ontology annotations for the discovery of new GO relationships.

    Science.gov (United States)

    Manda, Prashanti; McCarthy, Fiona; Bridges, Susan M

    2013-10-01

    The Gene Ontology (GO), a set of three sub-ontologies, is one of the most popular bio-ontologies used for describing gene product characteristics. GO annotation data containing terms from multiple sub-ontologies and at different levels in the ontologies is an important source of implicit relationships between terms from the three sub-ontologies. Data mining techniques such as association rule mining that are tailored to mine from multiple ontologies at multiple levels of abstraction are required for effective knowledge discovery from GO annotation data. We present a data mining approach, Multi-ontology data mining at All Levels (MOAL) that uses the structure and relationships of the GO to mine multi-ontology multi-level association rules. We introduce two interestingness measures: Multi-ontology Support (MOSupport) and Multi-ontology Confidence (MOConfidence) customized to evaluate multi-ontology multi-level association rules. We also describe a variety of post-processing strategies for pruning uninteresting rules. We use publicly available GO annotation data to demonstrate our methods with respect to two applications (1) the discovery of co-annotation suggestions and (2) the discovery of new cross-ontology relationships. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

  20. The High Level Mathematical Models in Calculating Aircraft Gas Turbine Engine Parameters

    Directory of Open Access Journals (Sweden)

    Yu. A. Ezrokhi

    2017-01-01

    Full Text Available The article describes high-level mathematical models developed to solve special problems arising at later stages of design with regard to calculation of the aircraft gas turbine engine (GTE under real operating conditions. The use of blade row mathematics models, as well as mathematical models of a higher level, including 2D and 3D description of the working process in the engine units and components, makes it possible to determine parameters and characteristics of the aircraft engine under conditions significantly different from the calculated ones.The paper considers application of mathematical modelling methods (MMM for solving a wide range of practical problems, such as forcing the engine by injection of water into the flowing part, estimate of the thermal instability effect on the GTE characteristics, simulation of engine start-up and windmill starting condition, etc. It shows that the MMM use, when optimizing the laws of the compressor stator control, as well as supplying cooling air to the hot turbine components in the motor system, can significantly improve the integral traction and economic characteristics of the engine in terms of its gas-dynamic stability, reliability and resource.It ought to bear in mind that blade row mathematical models of the engine are designed to solve purely "motor" problems and do not replace the existing models of various complexity levels used in calculation and design of compressors and turbines, because in “quality” a description of the working processes in these units is inevitably inferior to such specialized models.It is shown that the choice of the mathematical modelling level of an aircraft engine for solving a particular problem arising in its designing and computational study is to a large extent a compromise problem. Despite the significantly higher "resolution" and information ability the motor mathematical models containing 2D and 3D approaches to the calculation of flow in blade machine

  1. Aspects on Teaching/Learning with Object Oriented Programming for Entry Level Courses of Engineering.

    Science.gov (United States)

    de Oliveira, Clara Amelia; Conte, Marcos Fernando; Riso, Bernardo Goncalves

    This work presents a proposal for Teaching/Learning, on Object Oriented Programming for Entry Level Courses of Engineering and Computer Science, on University. The philosophy of Object Oriented Programming comes as a new pattern of solution for problems, where flexibility and reusability appears over the simple data structure and sequential…

  2. Solving bi-level optimization problems in engineering design using kriging models

    Science.gov (United States)

    Xia, Yi; Liu, Xiaojie; Du, Gang

    2018-05-01

    Stackelberg game-theoretic approaches are applied extensively in engineering design to handle distributed collaboration decisions. Bi-level genetic algorithms (BLGAs) and response surfaces have been used to solve the corresponding bi-level programming models. However, the computational costs for BLGAs often increase rapidly with the complexity of lower-level programs, and optimal solution functions sometimes cannot be approximated by response surfaces. This article proposes a new method, namely the optimal solution function approximation by kriging model (OSFAKM), in which kriging models are used to approximate the optimal solution functions. A detailed example demonstrates that OSFAKM can obtain better solutions than BLGAs and response surface-based methods, and at the same time reduce the workload of computation remarkably. Five benchmark problems and a case study of the optimal design of a thin-walled pressure vessel are also presented to illustrate the feasibility and potential of the proposed method for bi-level optimization in engineering design.

  3. Use of engineered soils and other site modifications for low-level radioactive waste disposal

    International Nuclear Information System (INIS)

    1994-08-01

    The U.S. Nuclear Regulatory Commission requires that low-level radioactive waste (LLW) disposal facilities be designed to minimize contact between waste and infiltrating water through the use of site design features. The purpose of this investigation is to identify engineered barriers and evaluate their ability to enhance the long-term performance of an LLW disposal facility. Previously used barriers such as concrete overpacks, vaults, backfill, and engineered soil covers, are evaluated as well as state-of-the-art barriers, including an engineered sorptive soil layer underlying a facility and an advanced design soil cover incorporating a double-capillary layer. The purpose of this investigation is also to provide information in incorporating or excluding specific engineered barriers as part of new disposal facility designs. Evaluations are performed using performance assessment modeling techniques. A generic reference disposal facility design is used as a baseline for comparing the improvements in long-term performance offered by designs incorporating engineered barriers in generic and humid environments. These evaluations simulate water infiltration through the facility, waste leaching, radionuclide transport through the facility, and decay and ingrowth. They also calculate a maximum (peak annual) dose for each disposal system design. A relative dose reduction factor is calculated for each design evaluated. The results of this investigation are presented for concrete overpacks, concrete vaults, sorptive backfill, sorptive engineered soil underlying the facility, and sloped engineered soil covers using a single-capillary barrier and a double-capillary barrier. Designs using combinations of barriers are also evaluated. These designs include a vault plus overpacks, sorptive backfill plus overpacks, and overpack with vault plus sorptive backfill, underlying sorptive soil, and engineered soil cover

  4. Enhanced Discrete-Time Scheduler Engine for MBMS E-UMTS System Level Simulator

    DEFF Research Database (Denmark)

    Pratas, Nuno; Rodrigues, António

    2007-01-01

    In this paper the design of an E-UMTS system level simulator developed for the study of optimization methods for the MBMS is presented. The simulator uses a discrete event based philosophy, which captures the dynamic behavior of the Radio Network System. This dynamic behavior includes the user...... mobility, radio interfaces and the Radio Access Network. Its given emphasis on the enhancements developed for the simulator core, the Event Scheduler Engine. Two implementations for the Event Scheduler Engine are proposed, one optimized for single core processors and other for multi-core ones....

  5. Engineering high-level production of fatty alcohols by Saccharomyces cerevisiae from lignocellulosic feedstocks

    DEFF Research Database (Denmark)

    d'Espaux, Leo; Ghosh, Amit; Runguphan, Weerawat

    2017-01-01

    to similar to 20% of the maximum theoretical yield from glucose, the highest titers and yields reported to date in S. cerevisiae. We further demonstrate high-level production from lignocellulosic feedstocks derived from ionic-liquid treated switchgrass and sorghum, reaching 0.7 g/L in shake flasks......Fatty alcohols in the C12-C18 range are used in personal care products, lubricants, and potentially biofuels. These compounds can be produced from the fatty acid pathway by a fatty acid reductase (FAR), yet yields from the preferred industrial host Saccharomyces cerevisiae remain under 2......% of the theoretical maximum from glucose. Here we improved titer and yield of fatty alcohols using an approach involving quantitative analysis of protein levels and metabolic flux, engineering enzyme level and localization, pull-push-block engineering of carbon flux, and cofactor balancing. We compared four...

  6. Staff analysis of public comments on proposed rule 10 CFR Part 60, Disposal of High-Level Radioactive Wastes in Geologic Repositories

    International Nuclear Information System (INIS)

    1983-12-01

    On February 25, 1981, the Nuclear Regulatory Commission published rules which establish procedures for the licensing of geologic disposal, by the US Department of Energy, of high-level radioactive wastes. On July 8, 1981, proposed technical criteria which would be used in the evaluation of license applications under those procedural rules were published in the Federal Register. The Commission received 93 comment letters on the proposed technical criteria, 89 of which were received in time for the Commission to consider in preparing the final technical criteria which were published on June 21, 1983. This document presents a detailed analysis of the comments received on the proposed rule by the Commission's staff and also contains the Rationale for the Performance Objectives of 10 CFR Part 60

  7. High-level methodologies for grammar engineering, introduction to the special issue

    Directory of Open Access Journals (Sweden)

    Denys Duchier

    2015-06-01

    Full Text Available Grammar Engineering is the task of designing and implementing linguistically motivated electronic descriptions of natural language (so-called grammars. These grammars are expressed within well-defined theoretical frameworks, and offer a fine-grained description of natural language. While grammars were first used to describe syntax, that is to say, the relations between constituents in a sentence, they often go beyond syntax and include semantic information. Grammar engineering provides precise descriptions which can be used for natural language understanding and generation, making these valuable resources for various natural language applications, including textual entailment, dialogue systems, or machine translation. The first attempts at designing large-scale resource grammars were costly because of the complexity of the task (Erbach et al. 1990 and of the number of persons that were needed (see e.g. Doran et al. 1997. Advances in the field have led to the development of environments for semi-automatic grammar engineering, borrowing ideas from compilation (grammar engineering is compared with software development and machine learning. This special issue reports on new trends in the field, where grammar engineering benefits from elaborate high-level methodologies and techniques, dealing with various issues (both theoretical and practical.

  8. Reformulation of Engineering Education at Undergraduate Level in the Faculdad de Ingenieria y Ciencias Hidricas Universidad Nacional del Litoral--Water Resources and Engineering Degrees.

    Science.gov (United States)

    Theiler, Julio; Isla, Miguel; Arrillaga, Hugo; Ceirano, Eduardo; Lozeco, Cristobal

    This paper explains the educational changes in the Water Resources Engineering program offered by the Universidad Nacional del Litoral in Santa Fe, Argentina, for the last 20 years at the undergraduate level. The need for modernizing the engineering teaching program occurred due to changes in the social system in which the concepts of development…

  9. ANALYSIS OF SOUND PRESSURE LEVEL (SPL AND LAY OUT OF ENGINES IN THE FACTORY

    Directory of Open Access Journals (Sweden)

    Wijianto Wijianto

    2017-01-01

    Full Text Available Modeling layout of engines in the factory is very useful to know how many dB sound pressure level that are occur in the building in order to avoid hearing damage of employees that are caused by noise. The objective of this research is to know how many dB sound pressure level that are occur in the factory with engine composition such as boiler, diesel, turbine, motor and gear box with dimension of building are 40 m length, 35 m width and 10 m height. With MATLAB analysis can be obtain that the highest SPL is 104.7 dB and the lowest is 93.5 dB, so, this range are dangerous for human hearing. To avoid hearing damage in this area, employees must use hearing protector.

  10. Engineering design study for storage and disposal of intermediate level waste

    Energy Technology Data Exchange (ETDEWEB)

    Griffin, J R; Hackney, S; Richardson, J A; Heafield, W

    1982-11-01

    A conceptual design study is presented which covers both the storage and disposal of intermediate level waste; repositories in several rock formations are considered at a 300m depth. A total system is proposed including an engineered trench for ..beta gamma.. waste, emplacement systems and off site transportation. Safety during the emplacement phase and the radiological effects of human intrusion and geological catastrophies are considered.

  11. Performance of high level waste forms and engineered barriers under repository conditions

    International Nuclear Information System (INIS)

    1991-02-01

    The IAEA initiated in 1977 a co-ordinated research programme on the ''Evaluation of Solidified High-Level Waste Forms'' which was terminated in 1983. As there was a continuing need for international collaboration in research on solidified high-level waste form and spent fuel, the IAEA initiated a new programme in 1984. The new programme, besides including spent fuel and SYNROC, also placed greater emphasis on the effect of the engineered barriers of future repositories on the properties of the waste form. These engineered barriers included containers, overpacks, buffer and backfill materials etc. as components of the ''near-field'' of the repository. The Co-ordinated Research Programme on the Performance of High-Level Waste Forms and Engineered Barriers Under Repository Conditions had the objectives of promoting the exchange of information on the experience gained by different Member States in experimental performance data and technical model evaluation of solidified high level waste forms, components of the waste package and the complete waste management system under conditions relevant to final repository disposal. The programme includes studies on both irradiated spent fuel and glass and ceramic forms as the final solidified waste forms. The following topics were discussed: Leaching of vitrified high-level wastes, modelling of glass behaviour in clay, salt and granite repositories, environmental impacts of radionuclide release, synroc use for high--level waste solidification, leachate-rock interactions, spent fuel disposal in deep geologic repositories and radionuclide release mechanisms from various fuel types, radiolysis and selective leaching correlated with matrix alteration. Refs, figs and tabs

  12. Levels of Organisation in agent-based modelling for renewable resources management. Agricultural water management collective rules enforcement in the French Drome River Valley Case Study

    International Nuclear Information System (INIS)

    Abrami, G.

    2004-11-01

    Levels of Organisation in agent-based modelling for renewable resources management. Agricultural water management collective rules enforcement in the French Dr me River Valley Case Study. In the context of Agent-Based Modelling for participative renewable resources management, this thesis is concerned with representing multiple tangled levels of organisation of a system. The Agent-Group-Role (AGR) formalism is borrowed from computer science research. It has been conceptually specified to handle levels of organisation, and behaviours within levels of organisation. A design methodology dedicated to AGR modelling has been developed, together with an implementation of the formalism over a multi-agent platform. AGR models of agricultural water management in the French Dr me River Valley have been built and tested. This experiment demonstrates the AGR formalism ability to (1) clarify usually implicit hypothesis on action modes, scales or viewpoints (2) facilitate the definition of scenarios with various collective rules, and various rules in enforcement behaviours (3) generate bricks for generic irrigated catchment models. (author)

  13. A Two-Level Cache for Distributed Information Retrieval in Search Engines

    Directory of Open Access Journals (Sweden)

    Weizhe Zhang

    2013-01-01

    Full Text Available To improve the performance of distributed information retrieval in search engines, we propose a two-level cache structure based on the queries of the users’ logs. We extract the highest rank queries of users from the static cache, in which the queries are the most popular. We adopt the dynamic cache as an auxiliary to optimize the distribution of the cache data. We propose a distribution strategy of the cache data. The experiments prove that the hit rate, the efficiency, and the time consumption of the two-level cache have advantages compared with other structures of cache.

  14. A two-level cache for distributed information retrieval in search engines.

    Science.gov (United States)

    Zhang, Weizhe; He, Hui; Ye, Jianwei

    2013-01-01

    To improve the performance of distributed information retrieval in search engines, we propose a two-level cache structure based on the queries of the users' logs. We extract the highest rank queries of users from the static cache, in which the queries are the most popular. We adopt the dynamic cache as an auxiliary to optimize the distribution of the cache data. We propose a distribution strategy of the cache data. The experiments prove that the hit rate, the efficiency, and the time consumption of the two-level cache have advantages compared with other structures of cache.

  15. Security Research on Engineering Database System

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Engine engineering database system is an oriented C AD applied database management system that has the capability managing distributed data. The paper discusses the security issue of the engine engineering database management system (EDBMS). Through studying and analyzing the database security, to draw a series of securi ty rules, which reach B1, level security standard. Which includes discretionary access control (DAC), mandatory access control (MAC) and audit. The EDBMS implem ents functions of DAC, ...

  16. Challenges for Rule Systems on the Web

    Science.gov (United States)

    Hu, Yuh-Jong; Yeh, Ching-Long; Laun, Wolfgang

    The RuleML Challenge started in 2007 with the objective of inspiring the issues of implementation for management, integration, interoperation and interchange of rules in an open distributed environment, such as the Web. Rules are usually classified as three types: deductive rules, normative rules, and reactive rules. The reactive rules are further classified as ECA rules and production rules. The study of combination rule and ontology is traced back to an earlier active rule system for relational and object-oriented (OO) databases. Recently, this issue has become one of the most important research problems in the Semantic Web. Once we consider a computer executable policy as a declarative set of rules and ontologies that guides the behavior of entities within a system, we have a flexible way to implement real world policies without rewriting the computer code, as we did before. Fortunately, we have de facto rule markup languages, such as RuleML or RIF to achieve the portability and interchange of rules for different rule systems. Otherwise, executing real-life rule-based applications on the Web is almost impossible. Several commercial or open source rule engines are available for the rule-based applications. However, we still need a standard rule language and benchmark for not only to compare the rule systems but also to measure the progress in the field. Finally, a number of real-life rule-based use cases will be investigated to demonstrate the applicability of current rule systems on the Web.

  17. Transfer between local and global processing levels by pigeons (Columba livia) and humans (Homo sapiens) in exemplar- and rule-based categorization tasks.

    Science.gov (United States)

    Aust, Ulrike; Braunöder, Elisabeth

    2015-02-01

    The present experiment investigated pigeons' and humans' processing styles-local or global-in an exemplar-based visual categorization task in which category membership of every stimulus had to be learned individually, and in a rule-based task in which category membership was defined by a perceptual rule. Group Intact was trained with the original pictures (providing both intact local and global information), Group Scrambled was trained with scrambled versions of the same pictures (impairing global information), and Group Blurred was trained with blurred versions (impairing local information). Subsequently, all subjects were tested for transfer to the 2 untrained presentation modes. Humans outperformed pigeons regarding learning speed and accuracy as well as transfer performance and showed good learning irrespective of group assignment, whereas the pigeons of Group Blurred needed longer to learn the training tasks than the pigeons of Groups Intact and Scrambled. Also, whereas humans generalized equally well to any novel presentation mode, pigeons' transfer from and to blurred stimuli was impaired. Both species showed faster learning and, for the most part, better transfer in the rule-based than in the exemplar-based task, but there was no evidence of the used processing mode depending on the type of task (exemplar- or rule-based). Whereas pigeons relied on local information throughout, humans did not show a preference for either processing level. Additional tests with grayscale versions of the training stimuli, with versions that were both blurred and scrambled, and with novel instances of the rule-based task confirmed and further extended these findings. PsycINFO Database Record (c) 2015 APA, all rights reserved.

  18. Engineering of the institutionalization of the circular economy at the level of casting production

    Science.gov (United States)

    Vescan, M. M.; Soporan, V. F.; Crișan, D. M.; Lehene, T. R.; Pădurețu, S.; Samuila, V.

    2017-06-01

    This paper is motivated by the necessity of introducing the principles of circular economy at the level of different social - economic activities, and from this point of view one of the fields with a special potential is that of the manufacture of castings. Objective: to connect to the organizing and application of the methodology of the circular economy principles. The proposed method is an innovating one, being connected to the use of institutionalization engineering. Formulating the subject: The subject formulated to be solved aims at the introduction of new approaches, defined through institutionalization engineering, which proposes to set the correlation of actions between the specifics of the circular economy and the specific elements of the manufacture of castings. Research method: An institutional structuring operation was imposed for the optimization of the research method, in which different versions interact at the following levels: the level of public policies, the level of the regulatory framework, the level of technical solutions and the level of financing solutions and financial instruments. The determination of the optimal solution established in a dynamic context, favorable for the requirements of the different actors present within the process, appeals to the elements of critical thinking, specific for the engineer’s actions. Achievement of the research activity: The research activity structures a methodology of quantifying the contributions of each stage of the manufacturing process for castings at the fulfilling of the specific conditions of the circular economy, indicating the critical areas of action for more efficient actions of the circular economy, according to the market economy requirements, where there is a potential of implementing the technical solutions by quantizing the financial solutions and the opportunity of using the financial instruments. The major contribution of the research: The proposed methodology, with examples at the

  19. Genome-Wide Tuning of Protein Expression Levels to Rapidly Engineer Microbial Traits.

    Science.gov (United States)

    Freed, Emily F; Winkler, James D; Weiss, Sophie J; Garst, Andrew D; Mutalik, Vivek K; Arkin, Adam P; Knight, Rob; Gill, Ryan T

    2015-11-20

    The reliable engineering of biological systems requires quantitative mapping of predictable and context-independent expression over a broad range of protein expression levels. However, current techniques for modifying expression levels are cumbersome and are not amenable to high-throughput approaches. Here we present major improvements to current techniques through the design and construction of E. coli genome-wide libraries using synthetic DNA cassettes that can tune expression over a ∼10(4) range. The cassettes also contain molecular barcodes that are optimized for next-generation sequencing, enabling rapid and quantitative tracking of alleles that have the highest fitness advantage. We show these libraries can be used to determine which genes and expression levels confer greater fitness to E. coli under different growth conditions.

  20. Conceptual design of the virtual engineering system for high level radioactive waste geological disposal

    International Nuclear Information System (INIS)

    2000-02-01

    The role of Virtual Engineering System for High Level Radioactive Waste Geological Disposal (hereafter the VES) is to accumulate and unify the results of research and development which JNC had been carried out for the completion of the second progress report on a computer system. The purpose and functions of VES with considering the long-term plan for geological disposal in Japan was studied. The analysis between geological environment assessment, safety performance assessment, and engineering technology had not been integrated mutually in the conventional study. The iterative analysis performed by VES makes it possible to analyze natural barrier and engineering barrier more quantitatively for obtaining safety margin and rationalization of the design of a waste repository. We have examined the system functions to achieve the above purpose of VES. Next, conceptual design for codes, databases, and utilities that consist of VES were performed by examining their purpose and functions. The conceptual design of geological environment assessment system, safety performance assessment system, waste repository element database, economical assessment system, investigation support system, quality assurance system, and visualization system are preformed. The whole system configuration, examination of suitable configuration of hardware and software, examination of system implementation, the confirmation of parallel calculation technology, the conceptual design of platform, the development of demonstration program of platform are performed. Based upon studies stated above, the VES development plan including prototype development during the period of selection of the site candidate was studied. The concept of VES was build based on the examination stated above. (author)

  1. System-Level Value of a Gas Engine Power Plant in Electricity and Reserve Production

    Directory of Open Access Journals (Sweden)

    Antti Alahäivälä

    2017-07-01

    Full Text Available Power systems require a certain amount of flexibility to meet varying demand and to be able to cope with unexpected events, and this requirement is expected to increase with the emergence of variable power generation. In this paper, we focus on gas engine power plant technology and the beneficial influence its flexible operation can have on a power system. The study introduces the concept of a combined-cycle gas engine power plant (CCGE, which comprises a combination of several gas-fired combustion engines and a steam turbine. The operation of CCGE is then comprehensively analyzed in electricity and reserve production in the South African power system and compared with combined-cycle gas turbine (CCGT technology. Even though CCGE is a form of technology that has already been commercialized, it is rarely considered as a source of flexibility in the academic research. That is the notion providing the motivation for this study. Our core contribution is to show that the flexibility of CCGE can be valuable in power systems. The methodology is based on the unit-level model of the studied system and the solving of a day-ahead unit commitment problem for each day of the simulated 11-year period. The simulation studies reveal how a CCGE is able to offer system flexibility to follow hourly load variations and capacity to provide reserve power effectively.

  2. Engineering Undergraduates' Views of A-Level Mathematics and Further Mathematics as Preparation for Their Degree

    Science.gov (United States)

    Darlington, Ellie; Bowyer, Jessica

    2017-01-01

    An ongoing reform programme of the post-16 Advanced "A"-level qualifications in England and Wales means that pre-university mathematics content and assessment will change from 2017. Undergraduate engineering is a subject that relies heavily on mathematics, and applicants to engineering degree programmes in the UK are required to have…

  3. 324 Building radiochemical engineering cells, high-level vault, low-level vault, and associated areas closure plan

    International Nuclear Information System (INIS)

    Barnett, J.M.

    1998-01-01

    The Hanford Site, located adjacent to and north of Richland, Washington, is operated by the US Department of Energy, Richland Operations Office (RL). The 324 Building is located in the 300 Area of the Hanford Site. The 324 Building was constructed in the 1960s to support materials and chemical process research and development activities ranging from laboratory/bench-scale studies to full engineering-scale pilot plant demonstrations. In the mid-1990s, it was determined that dangerous waste and waste residues were being stored for greater than 90 days in the 324 Building Radiochemical Engineering Cells (REC) and in the High-Level Vault/Low-Level Vault (HLV/LLV) tanks. [These areas are not Resource Conservation and Recovery Act of 1976 (RCRA) permitted portions of the 324 Building.] Through the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement) Milestone M-89, agreement was reached to close the nonpermitted RCRA unit in the 324 Building. This closure plan, managed under TPA Milestone M-20-55, addresses the identified building areas targeted by the Tri-Party Agreement and provides commitments to achieve the highest degree of compliance practicable, given the special technical difficulties of managing mixed waste that contains high-activity radioactive materials, and the physical limitations of working remotely in the areas within the subject closure unit. This closure plan is divided into nine chapters. Chapter 1.0 provides the introduction, historical perspective, 324 Building history and current mission, and the regulatory basis and strategy for managing the closure unit. Chapters 2.0, 3.0, 4.0, and 5.0 discuss the detailed facility description, process information, waste characteristics, and groundwater monitoring respectively. Chapter 6.0 deals with the closure strategy and performance standard, including the closure activities for the B-Cell, D-Cell, HLV, LLV; piping and miscellaneous associated building areas. Chapter 7.0 addresses the

  4. Considerations for closure of low-level radioactive waste engineered disposal facilities

    International Nuclear Information System (INIS)

    1992-01-01

    Proper stabilization and closure of low-level radioactive waste disposal facilities require detailed planning during the early stages of facility development. This report provides considerations for host States, compact regions, and unaffiliated States on stabilization and closure of engineered low-level radioactive waste and mixed waste disposal facilities. A time line for planning closure activities, which identifies closure considerations to be addressed during various stages of a facility's development, is presented. Current Federal regulatory requirements and guidance for closure and post-closure are outlined. Significant differences between host State and Federal closure requirements are identified. Design features used as stabilization measures that support closure, such as waste forms and containers, backfill materials, engineered barrier systems, and site drainage systems, are described. These design features are identified and evaluated in terms of how they promote long-term site stability by minimizing water infiltration, controlling subsidence and surface erosion, and deterring intrusion. Design and construction features critical to successful closure are presented for covers and site drainage. General considerations for stabilization and closure operations are introduced. The role of performance and environmental monitoring during closure is described

  5. Integration of emergency action levels with Combustion Engineering Emergency Operating Procedures

    International Nuclear Information System (INIS)

    Faletti, D.W.; Jamison, J.D.

    1985-09-01

    This report documents the development of a method for integrating Emergency Action Levels (EALs) with plant-specific Emergency Operating Procedures (EOPs) using the Combustion Engineering Owners' Group Emergency Operating Procedure Technical Guidelines (CEOG EOPTFs). EALs are discrete conditions or values of plant operating parameters which, if exceeded, require declaration of an appropriate level of emergency. At most operating plants, the EALs and event classification procedures are totally separate from the Emergency Operating Procedures used by the plant staff to control the plant during abnormal conditions. Control room personnel using the EOPs to deal with abnormal plant conditions must recognize when plant safety is sufficiently degraded that an emergency declaration may be warranted, and then enter a separate classification procedure containing EALs for a number of plant conditions and parameters. The operator then compares the existing plant conditions to the EALs and makes an emergency declaration accordingly. Using the Combustion Engineering Owners' Group Technical Guidelines document, a set of emergency class definitions and criteria were developed based on the status of the three main fission product barriers (fuel cladding, primary coolant system and containment). The EOPTGs were then annotated with suggested guidance to a procedure writer. The proposed method was tested by applying it to the reactor accident sequences that were shown in the reactor safety study to dominate accident risk. The object of the test was to determine if an EAL set linked to the EOP annotations would produce timely and accurate classification of the risk-dominant sequences. 6 refs., 13 figs., 31 tabs

  6. Glass: a candidate engineered material for management of high level nuclear waste

    International Nuclear Information System (INIS)

    Mishra, R.K.; Kaushik, C.P.

    2011-01-01

    While the commercial importance of glass is generally recognized, a few people are aware of extremely wide range of glass formulations that can be made and of the versatility of this engineered material. Some of the recent developments in the field of glass leading to various technological applications include glass fiber reinforcement of cement to give new building materials, substrates for microelectronics circuitry in form of semiconducting glasses, nuclear waste immobilization and specific medical applications. The present paper covers fundamental understanding of glass structure and its application for immobilization of high level radioactive liquid waste. High level radioactive liquid waste (HLW) arising during reprocessing of spent fuel are immobilized in sodium borosilicate glass matrix developed indigenously. Glass compositions are modified according to the composition of HLW to meet the criteria of desirable properties in terms. These glass matrices have been characterized for different properties like homogeneity, chemical durability, thermal stability and radiation stability. (author)

  7. Feasibility of disposal of high-level radioactive waste into the seabed. Volume 4: Engineering

    International Nuclear Information System (INIS)

    Hickerson, J.; Freeman, T.J.; Boisson, J.Y.; Murray, C.N.; Gera, F.; Nakamura, H.; Nieuwenhuis, J.D.; Schaller, K.H.

    1988-01-01

    One of the options suggested for disposal of high-level radioactive waste resulting from the generation of nuclear power is burial beneath the deep ocean floor in geologically stable sediment formations which have no economic value. The 8-volume series provides an assessment of the technical feasibility and radiological safety of this disposal concept based on the results obtained by ten years of co-operation and information exchange among the Member countries participating in the NEA Seabed Working Group. This report summarizes work performed to develop and evaluate engineering methods of emplacing high level radioactive waste in stable, deep ocean sediments. It includes results of desktop studies, laboratory experiments and field tests conducted in deep water

  8. Application of the level set method for multi-phase flow computation in fusion engineering

    International Nuclear Information System (INIS)

    Luo, X-Y.; Ni, M-J.; Ying, A.; Abdou, M.

    2006-01-01

    Numerical simulation of multi-phase flow is essential to evaluate the feasibility of a liquid protection scheme for the power plant chamber. The level set method is one of the best methods for computing and analyzing the motion of interface among the multi-phase flow. This paper presents a general formula for the second-order projection method combined with the level set method to simulate unsteady incompressible multi-phase flow with/out phase change flow encountered in fusion science and engineering. The third-order ENO scheme and second-order semi-implicit Crank-Nicholson scheme is used to update the convective and diffusion term. The numerical results show this method can handle the complex deformation of the interface and the effect of liquid-vapor phase change will be included in the future work

  9. Self-Driving Cars and Engineering Ethics: The Need for a System Level Analysis.

    Science.gov (United States)

    Borenstein, Jason; Herkert, Joseph R; Miller, Keith W

    2017-11-13

    The literature on self-driving cars and ethics continues to grow. Yet much of it focuses on ethical complexities emerging from an individual vehicle. That is an important but insufficient step towards determining how the technology will impact human lives and society more generally. What must complement ongoing discussions is a broader, system level of analysis that engages with the interactions and effects that these cars will have on one another and on the socio-technical systems in which they are embedded. To bring the conversation of self-driving cars to the system level, we make use of two traffic scenarios which highlight some of the complexities that designers, policymakers, and others should consider related to the technology. We then describe three approaches that could be used to address such complexities and their associated shortcomings. We conclude by bringing attention to the "Moral Responsibility for Computing Artifacts: The Rules", a framework that can provide insight into how to approach ethical issues related to self-driving cars.

  10. System Level Design of Reconfigurable Server Farms Using Elliptic Curve Cryptography Processor Engines

    Directory of Open Access Journals (Sweden)

    Sangook Moon

    2014-01-01

    Full Text Available As today’s hardware architecture becomes more and more complicated, it is getting harder to modify or improve the microarchitecture of a design in register transfer level (RTL. Consequently, traditional methods we have used to develop a design are not capable of coping with complex designs. In this paper, we suggest a way of designing complex digital logic circuits with a soft and advanced type of SystemVerilog at an electronic system level. We apply the concept of design-and-reuse with a high level of abstraction to implement elliptic curve crypto-processor server farms. With the concept of the superior level of abstraction to the RTL used with the traditional HDL design, we successfully achieved the soft implementation of the crypto-processor server farms as well as robust test bench code with trivial effort in the same simulation environment. Otherwise, it could have required error-prone Verilog simulations for the hardware IPs and other time-consuming jobs such as C/SystemC verification for the software, sacrificing more time and effort. In the design of the elliptic curve cryptography processor engine, we propose a 3X faster GF(2m serial multiplication architecture.

  11. Execution techniques for high level radioactive waste disposal. 4. Design and manufacturing procedure of engineered barriers

    International Nuclear Information System (INIS)

    Ogata, Nobuhide; Kosaki, Akio; Ueda, Hiroyoshi; Asano, Hidekazu; Takao, Hajime

    1999-01-01

    Ensuring the physical integrity of engineered barriers for an extremely long time period is necessary for geological disposal of high-level radioactive wastes. This report describes the design process and the designed configurations of both overpack and buffer as engineered barriers. Manufacturing procedure, quality control and inspection methods are also summarized. Carbon steel was selected as a structural material of the overpack and the specification of the overpack was determined assuming disposal in the depths of 1000 m below surface of crystalline rock site. The mixture of bentonite and sand (80% sodium bentonite and 20% silica sand by mass) was selected as material for a buffer from mainly its permeability and characteristics of self-sealing of a gap occurred in construction work. Welding method of a lid onto the main body of the overpack, uniting method of a corrosion-resistance layer and the structural component in the case of a composite overpack and manufacturing procedures of both blocks-type and monolithic-type buffers are also investigated. (author)

  12. Preliminary analysis of engineered barrieer performances in geological disposal of high level waste

    International Nuclear Information System (INIS)

    Ohe, Toshiaki; Maki, Yasuo; Tanaka, Hiroshi; Kawanishi, Motoi.

    1988-01-01

    This report represents preliminary results of safety analysis of a engineered barrier system in geological disposal of high level radioactive waste. Three well-known computer codes; ORIGEN 2, TRUMP, and SWIFT were used in the simulation. Main conceptual design of the repository was almost identical to that of SKB in Sweden and NAGRA in Switzerland; the engineered barrier conasists glass solidified waste, steel overpack, and compacted bentonite. Two different underground formations are considered; granite and neogene sedimentary rock, which are typically found in Japan. We first determined the repository configuration, particularly the space between disposal pitts. The ORIGEN 2 was used to estimate heat generation in the waste glass reprocessed at 4 years after removal from PWR. Then, temperature distribution was calculated by the TRUMP. The results of two or three dimensional calculation indicated that the pit interval should be kept more than 5 m in the case of granite formation at 500 m depth, according to the temperature criteria in the bentonite layer ( 90 Sr, 241 Am, 239 Pu, and 237 Np were chosen in one or two dimensional calculations. For both cases of steady release and instanteneous release, the maximum concentration in the pore water at the boundary between bentonite and surrounding rock had the following order; 237 Np> 239 Pu> 90 Sr> 241 Am. Sensitivity analysis showed that the order mainly due to the different adsorption characteristics of the nuclides in bentonite layer. (author)

  13. Use of engineered soils beneath low-level radioactive waste disposal facilities

    Energy Technology Data Exchange (ETDEWEB)

    Sandford, T.C.; Humphrey, D.N.; DeMascio, F.A. [Univ. of Maine, Orono, ME (United States). Dept. of Civil Engineering

    1993-03-01

    Current regulations are oriented toward locating low-level radioactive waste disposal facilities on sites that have a substantial natural soil barrier and are above the groundwater table. In some of the northern states, like Maine, the overburden soils are glacially derived and in most places provide a thin cover over bedrock with a high groundwater table. Thus, the orientation of current regulations can severely limit the availability of suitable sites. A common characteristic of many locations in glaciated regions is the rapid change of soil types that may occur and the heterogeneity within a given soil type. In addition, the bedrock may be fractured, providing avenues for water movement. A reliable characterization of these sites can be difficult, even with a detailed subsurface exploration program. Moreover, fluctuating groundwater and frost as well as the natural deposition processes have introduced macro features such as cracks, fissures, sand and silt seams, and root holes. The significant effect that these macro features have on the permeability and adsorptive capacity of a large mass is often ignored or poorly accounted for in the analyses. This paper will examine an alternate approach, which is to use engineered soils as a substitute for some or all of the natural soil and to treat the fractures in the underlying bedrock. The site selection would no longer be primarily determined by the natural soil and rock and could even be placed in locations with no existing soils. Engineered soils can be used for below- or aboveground facilities.

  14. A Measurement Framework for Team Level Assessment of Innovation Capability in Early Requirements Engineering

    Science.gov (United States)

    Regnell, Björn; Höst, Martin; Nilsson, Fredrik; Bengtsson, Henrik

    When developing software-intensive products for a market-place it is important for a development organisation to create innovative features for coming releases in order to achieve advantage over competitors. This paper focuses on assessment of innovation capability at team level in relation to the requirements engineering that is taking place before the actual product development projects are decided, when new business models, technology opportunities and intellectual property rights are created and investigated through e.g. prototyping and concept development. The result is a measurement framework focusing on four areas: innovation elicitation, selection, impact and ways-of-working. For each area, candidate measurements were derived from interviews to be used as inspiration in the development of a tailored measurement program. The framework is based on interviews with participants of a software team with specific innovation responsibilities and validated through cross-case analysis and feedback from practitioners.

  15. Low-level waste incineration at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Gillins, R.L.; Davis, J.N.; Maughan, R.Y.; Logan, J.A.

    1985-01-01

    A facility for the incineration of low-level beta/gamma contaminated combustible waste has been constructed at the Waste Experimental Reduction Facility (WERF) at the Idaho National Engineering Laboratory (INEL). The incineration facility was established to: (1) reduce the volume of currently generated contaminated combustible waste being disposed at the INEL's radioactive waste disposal site and thereby prolong the site's useful life; and (2) develop waste processing technology by providing a facility where full-size processes and equipment can be demonstrated and proven during production-scale operations. Cold systems testing has been completed, and contaminated operations began in September of 1984. Currently the facility is processing waste packaged in 2 x 2 x 2 ft cardboard boxes and measuring <10mR/h at contact. 3 figs

  16. Selection of a computer code for Hanford low-level waste engineered-system performance assessment

    International Nuclear Information System (INIS)

    McGrail, B.P.; Mahoney, L.A.

    1995-10-01

    Planned performance assessments for the proposed disposal of low-level waste (LLW) glass produced from remediation of wastes stored in underground tanks at Hanford, Washington will require calculations of radionuclide release rates from the subsurface disposal facility. These calculations will be done with the aid of computer codes. Currently available computer codes were ranked in terms of the feature sets implemented in the code that match a set of physical, chemical, numerical, and functional capabilities needed to assess release rates from the engineered system. The needed capabilities were identified from an analysis of the important physical and chemical process expected to affect LLW glass corrosion and the mobility of radionuclides. The highest ranked computer code was found to be the ARES-CT code developed at PNL for the US Department of Energy for evaluation of and land disposal sites

  17. Low-level waste incineration: experience at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Bohrer, H.A.; Dalton, J.D.

    1987-01-01

    The Waste Experimental Reduction Facility (WERF) is a low level radioactive waste treatment facility being operated at the Idaho National Engineering Laboratory (INEL). A key component of the facility is a dual chambered controlled air incinerator with a dry off-gas treatment system. The incinerator began processing radioactive waste in September, 1984. Limited operations continued from that data until October, 1985, at which time all INEL generators began shipping combustible waste for incineration. The incinerator is presently processing all available INEL combustible Dry Active Waste (DAW) (approximately 1700 m 3 per year) operating about five days per month. Performance to date has demonstrated the effectiveness, viability and safety of incineration as a volume reduction method of DAW. 3 figures

  18. Commercial disposal options for Idaho National Engineering Laboratory low-level radioactive waste

    International Nuclear Information System (INIS)

    Porter, C.L.; Widmayer, D.A.

    1995-09-01

    The Idaho National Engineering Laboratory (INEL) is a Department of Energy (DOE)-owned, contractor-operated site. Significant quantities of low-level radioactive waste (LLW) have been generated and disposed of onsite at the Radioactive Waste Management Complex (RWMC). The INEL expects to continue generating LLW while performing its mission and as aging facilities are decommissioned. An on-going Performance Assessment process for the RWMC underscores the potential for reduced or limited LLW disposal capacity at the existing onsite facility. In order to properly manage the anticipated amount of LLW, the INEL is investigating various disposal options. These options include building a new facility, disposing the LLW at other DOE sites, using commercial disposal facilities, or seeking a combination of options. This evaluation reports on the feasibility of using commercial disposal facilities

  19. A regulatory perspective on design and performance requirements for engineered systems in high-level waste

    International Nuclear Information System (INIS)

    Bernero, R.M.

    1992-01-01

    For engineered systems, this paper gives an overview of some of the current activities at the U.S. Nuclear Regulatory Commission (NRC), with the intent of elucidating how the regulatory process works in the management of high-level waste (HLW). Throughout the waste management cycle, starting with packaging and transportation, and continuing to final closure of a repository, these activities are directed at taking advantage of the prelicensing consultation period, a period in which the NRC, DOE and others can interact in ways that will reduce regulatory, technical and institutional uncertainties, and open the path to development and construction of a deep geologic repository for permanent disposal of HLW. Needed interactions in the HLW program are highlighted. Examples of HLW regulatory activities are given in discussions of a multipurpose-cask concept and of current NRC work on the meaning of the term substantially complete containment

  20. Operational and engineering developments in the management of low-level radioactive waste at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Kendall, E.W.; McKinney, J.D.; Wehmann, G.

    1979-01-01

    The Radioactive Waste Management Complex (RWMC) of the Idaho National Engineering Laboratory is a site for shallow land disposal and storage of solid radioactive waste. It is currently operated for ERDA by EG and G Idaho, Inc. The facility has accepted radioactive waste since July 1952. Both transuranic and non-transuranic wastes are handled at the complex. This document describes the operational and engineering developments in waste handling and storage practices that have been developed during the 25 years of waste handling operations. Emphasis is placed on above-ground transuranic waste storage, subsurface transuranic waste retrieval, and beta/gamma compaction disposal. The proposed future programs for the RWMC including a Molten Salt Combustion Facility and Production Scale Retrieval Project are described

  1. A top-down approach in control engineering third-level teaching: The case of hydrogen-generation

    Science.gov (United States)

    Setiawan, Eko; Habibi, M. Afnan; Fall, Cheikh; Hodaka, Ichijo

    2017-09-01

    This paper presents a top-down approach in control engineering third-level teaching. The paper shows the control engineering solution for the issue of practical implementation in order to motivate students. The proposed strategy only focuses on one technique of control engineering to lead student correctly. The proposed teaching steps are 1) defining the problem, 2) listing of acquired knowledge or required skill, 3) selecting of one control engineering technique, 4) arrangement the order of teaching: problem introduction, implementation of control engineering technique, explanation of system block diagram, model derivation, controller design, and 5) enrichment knowledge by the other control techniques. The approach presented highlights hardware implementation and the use of software simulation as a self-learning tool for students.

  2. Automated System of Diagnostic Monitoring at Bureya HPP Hydraulic Engineering Installations: a New Level of Safety

    International Nuclear Information System (INIS)

    Musyurka, A. V.

    2016-01-01

    This article presents the design, hardware, and software solutions developed and placed in service for the automated system of diagnostic monitoring (ASDM) for hydraulic engineering installations at the Bureya HPP, and assuring a reliable process for monitoring hydraulic engineering installations. Project implementation represents a timely solution of problems addressed by the hydraulic engineering installation diagnostics section.

  3. Automated System of Diagnostic Monitoring at Bureya HPP Hydraulic Engineering Installations: a New Level of Safety

    Energy Technology Data Exchange (ETDEWEB)

    Musyurka, A. V., E-mail: musyurkaav@burges.rushydro.ru [Bureya HPP (a JSC RusGidro affiliate) (Russian Federation)

    2016-09-15

    This article presents the design, hardware, and software solutions developed and placed in service for the automated system of diagnostic monitoring (ASDM) for hydraulic engineering installations at the Bureya HPP, and assuring a reliable process for monitoring hydraulic engineering installations. Project implementation represents a timely solution of problems addressed by the hydraulic engineering installation diagnostics section.

  4. HIGH LEVEL WASTE TANK CLOSURE PROJECT AT THE IDAHO NATIONAL ENGINEERING AND ENVIRONMENTAL LABORATORY

    International Nuclear Information System (INIS)

    Quigley, K.D.; Wessman, D.

    2003-01-01

    The Department of Energy, Idaho Operations Office (DOE-ID) is in the process of closing two underground high-level waste (HLW) storage tanks at the Idaho National Engineering and Environmental Laboratory (INEEL) to meet Resource Conservation and Recovery Act (RCRA) regulations and Department of Energy orders. Closure of these two tanks is scheduled for 2004 as the first phase in closure of the eleven 1.14 million liter (300,000 gallon) tanks currently in service at the Idaho Nuclear Technology and Engineering Center (INTEC). The INTEC Tank Farm Facility (TFF) Closure sequence consists of multiple steps to be accomplished through the existing tank riser access points. Currently, the tank risers contain steam and process waste lines associated with the steam jets, corrosion coupons, and liquid level indicators. As necessary, this equipment will be removed from the risers to allow adequate space for closure equipment and activities. The basic tank closure sequence is as follows: Empty the tank to the residual heel using the existing jets; Video and sample the heel; Replace steam jets with new jet at a lower position in the tank, and remove additional material; Flush tank, piping and secondary containment with demineralized water; Video and sample the heel; Evaluate decontamination effectiveness; Displace the residual heel with multiple placements of grout; and Grout piping, vaults and remaining tank volume. Design, development, and deployment of a remotely operated tank cleaning system were completed in June 2002. The system incorporates many commercially available components, which have been adapted for application in cleaning high-level waste tanks. The system is cost-effective since it also utilizes existing waste transfer technology (steam jets), to remove tank heel solids from the tank bottoms during the cleaning operations. Remotely operated directional spray nozzles, automatic rotating wash balls, video monitoring equipment, decontamination spray-rings, and

  5. The Prospective External Validation of International Ovarian Tumor Analysis (IOTA) Simple Rules in the Hands of Level I and II Examiners.

    Science.gov (United States)

    Knafel, A; Banas, T; Nocun, A; Wiechec, M; Jach, R; Ludwin, A; Kabzinska-Turek, M; Pietrus, M; Pitynski, K

    2016-10-01

    Objective: To externally validate the International Ovarian Tumor Analysis (IOTA) Simple Rules (SR) by examiners with different levels of sonographic experience defined by the European Federation of Societies for Ultrasound in Medicine and Biology (EFSUMB) and to assess the morphological ultrasound features of the adnexal tumors classified as inconclusive based on IOTA SR. Materials and Methods: In the two-year prospective study adnexal tumors were assessed preoperatively with transvaginal ultrasound by examiners with different levels of experience (level 1- IOTA SR1, level 2-IOTA SR2). Additionally, an expert (level 3) evaluated all tumors by subjective assessment (SA). If the rules could not be applied, the tumors were considered inconclusive. The final diagnosis was based on the histopathological result of the removed mass. The diagnostic performance measures for the assessed model were sensitivity, specificity, negative (LR-) and positive(LR+) likelihood ratios, accuracy (ACC) and diagnostic odds ratio (DOR). Results: 226 women with adnexal tumors scheduled for surgery were included in the stutdy. The prevalence of malignancy was 36.3 % in the group of all studied tumors and was 52.5 % in the inconclusive group (n = 40) (p = 0.215). Fewer tumors were classified as inconclusive by level 2 examiners compared to level 1 examiners [20 (8.8 %) vs. 40 (17.7 %); p = 0.008], resulting from the discrepancy in the evaluation of acoustic shadows and the vascularization within the tumor. For level 1 examiners a diagnostic strategy using IOTA SR1 +MA (assuming malignancy when SR inconclusive) achieved a sensitivity, specificity and DOR of 96.3 %, 81.9 %, 13.624 respectively. For level 2 examiners the diagnostic strategy for IOTA SR2 +MA achieved a sensitivity, specificity and DOR of 95.1 %, 89.6 %, 137,143, respectively. Adding SA by an expert (or level 3 examiner) when IOTA SR were not applicable improved the specificity of the test and

  6. ANALYSIS OF MODERN REQUIREMENTS FOR THE LEVEL OF FOREIGN LANGUAGE PROFICIENCY OF ENGINEERING SPECIALISTS

    Directory of Open Access Journals (Sweden)

    K. M. Inozemtseva

    2017-01-01

    Full Text Available Introduction. At present, in Russian higher professional education we can observe a shift to the new educational paradigm based on Professional Standards (PS. According to the Federal Law of 02.05.2015 № 122 «About amendments to the Labour Code of Russian Federation and the articles 11 and 73 of «The Law on Education in Russian Federation» formation of the Federal State Educational Standards of Higher Education requirements for expected learning outcomes on universities’ main educational programs is implemented on the basis of relevant Professional Standards. This causes necessity of work on conjunction of Professional Standards, Federal State Educational Standards and universities’ main educational programs.The aim of this article is to demonstrate the influence of a new educational paradigm on the choice of contents, technologies and activities used in foreign language teaching at Russian technical universities.Methodology and research methods. The research methodology is based on the concept of diversification of engineers’ continuous professional foreign language training (T. Yu. Polyakova. In view of priority value of PS for developing universities’ main educational programs the updating of the above concept needs thorough analysis of both PS requirements for the level of foreign language proficiency of engineering specialists and study of scientific literature on the above problem.Results. This research results in interpretation and clarification of generalized PS requirements for the actual needs of industries and individuals in foreign language proficiency. The research also causes Language for Specific Purposes (LSP program developers’ and LSP teachers’ pedagogical reflection about their readiness to form foreign language (FL professional communicative competence of an engineer. It is concluded that a teacher needs to consider axiological aspects of engineering activity in order to understand the nature of the work

  7. We Are All Engineers Now: Delivering Useful Projections Of Sea Level Rise

    Science.gov (United States)

    Pfeffer, W. T.

    2011-12-01

    Sea level rise is among the most tangible and potentially costly global changes facing society in the near future. Much of the uncertainty in future sea level rise lies in the determination of glacier and ice sheet contributions through melting of ice and through the discharge of icebergs directly into the ocean. As a consequence, many aspects of modern glaciological research have come to be motivated wholly or in part by the need to solve societally relevant problems involving future changes in sea level. To this extent, glaciology has become - temporarily - an applied science, in which the motivating questions are not purely scientific but practical in nature, and entail goals, deadlines and constraints that may or may not mesh comfortably with the skills, resources, and interests of the glaciological research community. This shift in motivation has subtle but important effects on how the glaciological community conducts research: we are no longer fully at liberty to explore only those problems that we judge to be the most intellectually stimulating and novel, or even the most likely to produce immediate results. We are obliged, at least if we are going to claim to be serving a critical societal need, to take on the entire spectrum of problems pertinent to sea level rise: the exciting with the mundane, the low-hanging fruit with the high-hanging, the tractable with the intractable. And in those intractable cases, and in other situations where the path to a solution is unclear, we must explore alternatives to our conventional approaches, and seek the means, if not to actually obtain solutions, to at least constrain the outcome and reduce the uncertainty of future knowledge. This broadening of methods is very much an engineer's approach to problem solving, but it also fits the philosopher/physicist P.W. Bridgman's definition of the scientific method as "Doing your damnedest, no holds barred."

  8. Sea-level rise modeling handbook: Resource guide for coastal land managers, engineers, and scientists

    Science.gov (United States)

    Doyle, Thomas W.; Chivoiu, Bogdan; Enwright, Nicholas M.

    2015-08-24

    ; utility options for setting sea-level rise and climate change scenarios; and ease or difficulty of storing, displaying, or interpreting model output. Coastal land managers, engineers, and scientists can benefit from this synthesis of tools and models that have been developed for projecting causes and consequences of sea-level change on the landscape and seascape.

  9. 324 Radiochemical engineering cells and high level vault tanks mixed waste compliance status

    International Nuclear Information System (INIS)

    1994-01-01

    The 324 Building in the Hanford 300 Area contains Radiochemical Engineering Cells and High Level Vault tanks (the open-quotes REC/HLVclose quotes) for research and development activities involving radioactive materials. Radioactive mixed waste within this research installation, found primarily in B-Cell and three of the high level vault tanks, is subject to RCRA/DWR (open-quotes RCRAclose quotes) regulations for storage. This white paper provides a baseline RCRA compliance summary of MW management in the REC/HLV, based on best available knowledge. The REC/HLV compliance project, of which this paper is a part, is intended to achieve the highest degree of compliance practicable given the special technical difficulties of managing high activity radioactive materials, and to assure protection of human health and safety and the environment. The REC/HLV was constructed in 1965 to strict standards for the safe management of highly radioactive materials. Mixed waste in the REC/HLV consists of discarded tools and equipment, dried feed stock from nuclear waste melting experiments, contaminated particulate matter, and liquid feed stock from various experimental programs in the vault tanks. B-Cell contains most of these materials. Total radiological inventory in B-Cell is estimated at 3 MCi, about half of which is potentially open-quotes dispersibleclose quotes, that is, it is in small pieces or mobile particles. Most of the mixed waste currently in the REC/HLV was generated or introduced before mixed wastes were subjected to RCRA in 1987

  10. Engineering of Fermi level by nin diamond junction for control of charge states of NV centers

    Science.gov (United States)

    Murai, T.; Makino, T.; Kato, H.; Shimizu, M.; Murooka, T.; Herbschleb, E. D.; Doi, Y.; Morishita, H.; Fujiwara, M.; Hatano, M.; Yamasaki, S.; Mizuochi, N.

    2018-03-01

    The charge-state control of nitrogen-vacancy (NV) centers in diamond is very important toward its applications because the NV centers undergo stochastic charge-state transitions between the negative charge state (NV-) and the neutral charge state (NV0) of the NV center upon illumination. In this letter, engineering of the Fermi level by a nin diamond junction was demonstrated for the control of the charge state of the NV centers in the intrinsic (i) layer region. By changing the size (d) of the i-layer region between the phosphorus-doped n-type layer regions (nin) from 2 μm to 10 μm, we realized the gradual change in the NV- charge-state population in the i-layer region from 60% to 80% under 532 nm excitation, which can be attributed to the band bending in the i-layer region. Also, we quantitatively simulated the changes in the Fermi level in the i-layer region depending on d with various concentrations of impurities in the i-layer region.

  11. Conceptual design of the Virtual Engineering System for High Level Radioactive Waste Geological Disposal

    International Nuclear Information System (INIS)

    1999-06-01

    The Virtual Engineering System for the High Level Radioactive Waste Geological Disposal (hereafter the VE) adopts such computer science technologies as advanced numerical simulation technology with special emphasis upon computer graphics, massive parallel computing, high speed networking, knowledge engineering, database technology to virtually construct the natural and the part of social environment of disposal site in syberspace to realize the disposal OS as its final target. The principle of tile VE is to provide for a firm business standpoint after The 2000 Report by JNC and supply decision support system which promotes various evaluations needed to be done from the year of 2000 to the licensing application for disposal to the government. The VE conceptual design was performed in the year of 1998. The functions of the VE are derived from the analysis of work scope of implementing organization in each step of geological waste disposal: the VE functions need the safety performance assessment, individual process analysis, facility designing, cost evaluation, site surveillance, research and development, public acceptance. Then the above functions are materialized by integrating such individual system as geology database, groundwater database, safety performance assessment system, coupled phenomena analysis system, decision support system, cost evaluation system, and public acceptance system. The integration method of the systems was studied. The concept of the integration of simulators has also been studied from the view point of CAPASA program. Parallel computing, networking, and computer graphic for high speed massive scientific calculation were studied in detail as the element technology to achieve the VE. Based on studies stated above, the concept of the waste disposal project and subjects that arise from 1999 to licensing application are decided. (author)

  12. Proposed Rule for Control of Air Pollution From New Motor Vehicles: Proposed Heavy-Duty Engine and Vehicle Standards and Highway Diesel Fuel Sulfur Control Requirements

    Science.gov (United States)

    Rule summary, CFR citations and additional resources concerning proposed new emission standards that will begin to take effect in 2007 and corresponding diesel fuel requirements that take effect in 2006.

  13. Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines: State Commitments to National Low Emission Vehicle Program

    Science.gov (United States)

    The Environmental Protection Agency (EPA) is issuing a final rule representing the next step in establishing a voluntary nationwide program to make new cars significantly cleaner burning than today’s current cars.

  14. 33 CFR 210.4 - Rules of the Corps of Engineers Board of Contract Appeals for cases not subject to the Contract...

    Science.gov (United States)

    2010-07-01

    ... within the jurisdiction of any department or agency thereof. (w) Rule 22, Copies of papers. When books... the Board or otherwise to indicate an intention to continue the prosecution of an appeal filed, the...

  15. Implementing lean in Malaysian universities: Lean awareness level in an engineering faculty of a local university

    Science.gov (United States)

    Azim Khairi, M.; Rahman, Mohamed Abd

    2018-01-01

    Many academic articles were published in Malaysia promoting the goodness of lean in manufacturing and industrial sectors but less attention was apparently given to the possibility of obtaining the same universal benefits when applying lean in non-manufacturing sectors especially higher education. This study aims to determine the level of lean awareness among a local university’s community taking its Faculty of Engineering (FoE) as the case study. It also seeks to identify typical FoE’s staff perception on lean regarding its benefits and the obstacles in implementing it. A web-based survey using questionnaires was carried out for 215 respondents consisting of academic and administrative staff of the faculty. Statistical Package for the Social Science (SPSS) was used to analyze the survey data collected. A total of 13.95% of respondents returned the forms. Slightly more than half of those responded (56.7%) have encountered some of the lean terms with mean 1.43 and standard deviation 0.504. However, the large amount of standard deviation somewhat indicates that the real level of lean awareness of FoE as a group was low. In terms of lean benefits, reduction of waste was favored (93.3%) by the respondents with mean 0.93 and standard deviation 0.254. For obstacles in implementing lean, lack of knowledge was selected by most respondents (86.7%) to be the major factor with mean 0.87 and standard deviation 0.346. Through the analysis done, the study may conclude that level of lean awareness among the university‘s community was low thus may hinder implementation of lean concept.

  16. Metabolic engineering Camelina sativa with fish oil-like levels of DHA.

    Directory of Open Access Journals (Sweden)

    James R Petrie

    Full Text Available BACKGROUND: Omega-3 long-chain (≥C20 polyunsaturated fatty acids (ω3 LC-PUFA such as eicosapentaenoic acid (EPA and docosahexaenoic acid (DHA are critical for human health and development [corrected].. Numerous studies have indicated that deficiencies in these fatty acids can increase the risk or severity of cardiovascular, inflammatory and other diseases or disorders. EPA and DHA are predominantly sourced from marine fish although the primary producers are microalgae. Much work has been done to engineer a sustainable land-based source of EPA and DHA to reduce pressure on fish stocks in meeting future demand, with previous studies describing the production of fish oil-like levels of DHA in the model plant species, Arabidopsis thaliana. PRINCIPAL FINDINGS: In this study we describe the production of fish oil-like levels (>12% of DHA in the oilseed crop species Camelina sativa achieving a high ω3/ω6 ratio. The construct previously transformed in Arabidopsis as well as two modified construct versions designed to increase DHA production were used. DHA was found to be stable to at least the T5 generation and the EPA and DHA were found to be predominantly at the sn-1,3 positions of triacylglycerols. Transgenic and parental lines did not have different germination or seedling establishment rates. CONCLUSIONS: DHA can be produced at fish oil-like levels in industrially-relevant oilseed crop species using multi-gene construct designs which are stable over multiple generations. This study has implications for the future of sustainable EPA and DHA production from land-based sources.

  17. Effect of NTP technology levels on engine sizing for a 2005 piloted Mars mission

    Science.gov (United States)

    Burr, Annette D.; Cross, Elden H.; Widman, Frederick W.; North, D. Michael

    1993-01-01

    Previous vehicle mass studies were performed for Mars launch windows in the 2010-2018 time frame. Within the last year, a study was performed to determine the effects of various Nuclear Thermal Propulsion (NTP) engine and mission parameters on Initial Mass in Low Earth Orbit (MLEO) for a piloted Mars mission during the 2005 opportunity. Particle Bed Reactor (PBR) and Enabler-type reactors were compared. Parameters evaluated included engine thrust, number of engines, number of Trans-Mars Injection (TMI) burns, engine thrust/weight, engine out capability, engine burn time, and Isp. Earth and Mars departure dates and outbound and return travel times were optimized for a 240-day total interplanetary transfer time (long-duration stay mission). Parameters which were seen to reduce IMLEO included a greater number of perigee burns, multiple engines, and higher Isp. Optimum engine thrust varied substantially depending on the configuration. Engine models developed jointly by Rocketdyne and Westinghouse within the last year formed the basis for the Enabler thrust optimization study.

  18. Investigations of effects of pilot injection with change in level of compression ratio in a common rail diesel engine

    Directory of Open Access Journals (Sweden)

    Gajarlawar Nilesh

    2013-01-01

    Full Text Available These day diesel engines are gaining lots of attention as prime movers for various source of transportation. It offers better drive ability, very good low end torque and importantly the lower CO2 emission. Diesel engines are bridging the gap between gasoline and diesel engines. Better noise vibration and harshness levels of gasoline engine are realized to great extent in diesel engine, thanks to common rail direct injection system. Common rail injection system is now well known entity. Its unique advantage is flexible in operation. In common rail injection system, number of injection prior and after main injection at different injection pressure is possible. Due to multiple injections, gain in emission reduction as well as noise has been already experienced and demonstrated by researcher in the past. However, stringent emission norms for diesel engine equipped vehicle demands for further lower emission of oxides of nitrogen (NOx and particulate matter (PM. In the present paper, authors attempted to study the effect of multiple injections in combination with two level of compression ratio. The aim was to study the combustion behavior with the reduced compression ratio which is going to be tried out as low temperature combustion concept in near future. The results were compared with the current level of compression ratio. Experiments were carried out in 2.2L cubic capacity engine with two levels of compression ratios. Pilot injection separation and quantities were varied keeping the main injection, rail pressure, boost pressure and EGR rate constant. Cylinder pressure traces and gross heat release rates were measured and analyzed to understand the combustion behavior.

  19. Ensuring fair levels of executive directors’ remuneration: Regulation and use of principles against the use of detailed legal rules in determining the most effective approach for setting executive pay levels. A discussion

    Directory of Open Access Journals (Sweden)

    Ewgeni Hersonski

    2012-10-01

    Full Text Available The purpose of this paper is to present arguments concerning the fair levels of executive directors’ remuneration. It is argued that principles are a better way to achieve this goal. However, we also find arguments in support of detailed legal rules when dealing with this matter. Since both methods have their pros and cons the paper delivers a balanced discussion and also outlines how the executive pay is currently regulated in the UK, the United States as well as on the global scale.

  20. Predictable Particle Engineering: Programming the Energy Level, Carrier Generation, and Conductivity of Core-Shell Particles.

    Science.gov (United States)

    Yuan, Conghui; Wu, Tong; Mao, Jie; Chen, Ting; Li, Yuntong; Li, Min; Xu, Yiting; Zeng, Birong; Luo, Weiang; Yu, Lingke; Zheng, Gaofeng; Dai, Lizong

    2018-06-20

    Core-shell structures are of particular interest in the development of advanced composite materials as they can efficiently bring different components together at nanoscale. The advantage of this structure greatly relies on the crucial design of both core and shell, thus achieving an intercomponent synergistic effect. In this report, we show that decorating semiconductor nanocrystals with a boronate polymer shell can easily achieve programmable core-shell interactions. Taking ZnO and anatase TiO 2 nanocrystals as inner core examples, the effective core-shell interactions can narrow the band gap of semiconductor nanocrystals, change the HOMO and LUMO levels of boronate polymer shell, and significantly improve the carrier density of core-shell particles. The hole mobility of core-shell particles can be improved by almost 9 orders of magnitude in comparison with net boronate polymer, while the conductivity of core-shell particles is at most 30-fold of nanocrystals. The particle engineering strategy is based on two driving forces: catechol-surface binding and B-N dative bonding and having a high ability to control and predict the shell thickness. Also, this approach is applicable to various inorganic nanoparticles with different components, sizes, and shapes.

  1. Anticipated Degradation Modes of Metallic Engineered Barriers for High-Level Nuclear Waste Repositories

    Science.gov (United States)

    Rodríguez, Martín A.

    2014-03-01

    Metallic engineered barriers must provide a period of absolute containment to high-level radioactive waste in geological repositories. Candidate materials include copper alloys, carbon steels, stainless steels, nickel alloys, and titanium alloys. The national programs of nuclear waste management have to identify and assess the anticipated degradation modes of the selected materials in the corresponding repository environment, which evolves in time. Commonly assessed degradation modes include general corrosion, localized corrosion, stress-corrosion cracking, hydrogen-assisted cracking, and microbiologically influenced corrosion. Laboratory testing and modeling in metallurgical and environmental conditions of similar and higher aggressiveness than those expected in service conditions are used to evaluate the corrosion resistance of the materials. This review focuses on the anticipated degradation modes of the selected or reference materials as corrosion-resistant barriers in nuclear repositories. These degradation modes depend not only on the selected alloy but also on the near-field environment. The evolution of the near-field environment varies for saturated and unsaturated repositories considering backfilled and unbackfilled conditions. In saturated repositories, localized corrosion and stress-corrosion cracking may occur in the initial aerobic stage, while general corrosion and hydrogen-assisted cracking are the main degradation modes in the anaerobic stage. Unsaturated repositories would provide an oxidizing environment during the entire repository lifetime. Microbiologically influenced corrosion may be avoided or minimized by selecting an appropriate backfill material. Radiation effects are negligible provided that a thick-walled container or an inner shielding container is used.

  2. Exhaust emissions of low level blend alcohol fuels from two-stroke and four-stroke marine engines

    Science.gov (United States)

    Sevik, James M., Jr.

    The U.S. Renewable Fuel Standard mandates that by 2022, 36 billion gallons of renewable fuels must be produced on a yearly basis. Ethanol production is capped at 15 billion gallons, meaning 21 billion gallons must come from different alternative fuel sources. A viable alternative to reach the remainder of this mandate is iso-butanol. Unlike ethanol, iso-butanol does not phase separate when mixed with water, meaning it can be transported using traditional pipeline methods. Iso-butanol also has a lower oxygen content by mass, meaning it can displace more petroleum while maintaining the same oxygen concentration in the fuel blend. This research focused on studying the effects of low level alcohol fuels on marine engine emissions to assess the possibility of using iso-butanol as a replacement for ethanol. Three marine engines were used in this study, representing a wide range of what is currently in service in the United States. Two four-stroke engine and one two-stroke engine powered boats were tested in the tributaries of the Chesapeake Bay, near Annapolis, Maryland over the course of two rounds of weeklong testing in May and September. The engines were tested using a standard test cycle and emissions were sampled using constant volume sampling techniques. Specific emissions for two-stroke and four-stroke engines were compared to the baseline indolene tests. Because of the nature of the field testing, limited engine parameters were recorded. Therefore, the engine parameters analyzed aside from emissions were the operating relative air-to-fuel ratio and engine speed. Emissions trends from the baseline test to each alcohol fuel for the four-stroke engines were consistent, when analyzing a single round of testing. The same trends were not consistent when comparing separate rounds because of uncontrolled weather conditions and because the four-stroke engines operate without fuel control feedback during full load conditions. Emissions trends from the baseline test to each

  3. Design Rules for Life Support Systems

    Science.gov (United States)

    Jones, Harry

    2002-01-01

    This paper considers some of the common assumptions and engineering rules of thumb used in life support system design. One general design rule is that the longer the mission, the more the life support system should use recycling and regenerable technologies. A more specific rule is that, if the system grows more than half the food, the food plants will supply all the oxygen needed for the crew life support. There are many such design rules that help in planning the analysis of life support systems and in checking results. These rules are typically if-then statements describing the results of steady-state, "back of the envelope," mass flow calculations. They are useful in identifying plausible candidate life support system designs and in rough allocations between resupply and resource recovery. Life support system designers should always review the design rules and make quick steady state calculations before doing detailed design and dynamic simulation. This paper develops the basis for the different assumptions and design rules and discusses how they should be used. We start top-down, with the highest level requirement to sustain human beings in a closed environment off Earth. We consider the crew needs for air, water, and food. We then discuss atmosphere leakage and recycling losses. The needs to support the crew and to make up losses define the fundamental life support system requirements. We consider the trade-offs between resupplying and recycling oxygen, water, and food. The specific choices between resupply and recycling are determined by mission duration, presence of in-situ resources, etc., and are defining parameters of life support system design.

  4. Proposed Rule and Related Materials for Control of Emissions of Air Pollution From Nonroad Diesel Engines Control of Air Pollution From Aircraft and Aircraft Engines; Proposed Emission Standards and Test Procedures

    Science.gov (United States)

    EPA is proposing to adopt emission standards and related provisions for aircraft gas turbine engines with rated thrusts greater than 26.7 kilonewtons. These engines are used primarily on commercial passenger and freight aircraft.

  5. Systems engineering management and implementation plan for Project W-464, immobilized high-level waste storage

    International Nuclear Information System (INIS)

    Wecks, M.D.

    1998-01-01

    The Systems Engineering Management and Implementation Plan (SEMIP) for TWRS Project W-46 describes the project implementation of the Tank Waste Remediation System Systems Engineering Management Plan. (TWRS SEMP), Rev. 1. The SEMIP outlines systems engineering (SE) products and processes to be used by the project for technical baseline development. A formal graded approach is used to determine the products necessary for requirements, design, and operational baseline completion. SE management processes are defined, and roles and responsibilities for management processes and major technical baseline elements are documented

  6. Proceedings of the international seminar on chemistry and process engineering for high-level liquid waste solidification

    International Nuclear Information System (INIS)

    Odoj, R.; Merz, E.

    1981-06-01

    The proceedings record a very distinct phase of the chemistry and process engineering for high-level liquid waste solidification in the past years. The main purpose is to provide solutions which guarantee sufficient safe and economically acceptable measure causing no adverse consequence to man and his environment. (DG)

  7. The Application of an Engineering Design and Information Systems Case Study in a Senior Level Product Data Management Course

    Science.gov (United States)

    Connolly, Patrick

    2011-01-01

    This study examines the use of an engineering design and information systems case study over a three week period in a senior level class covering the topics of product data management (PDM) and product lifecycle management (PLM). Students that have taken the course in the past have struggled with the sometimes nebulous and difficult to…

  8. Final Rule for Control of Emissions From New Marine Compression-Ignition Engines at or Above 2.5 Liters Per Cylinder

    Science.gov (United States)

    The near-term, Tier 1 standards in this rule are equivalent to the internationally negotiated emission limits for oxides of nitrogen (NOx). These standards will go into effect in 2004 and are based on readily available emission-control technology.

  9. Performance analyses of naval ships based on engineering level of simulation at the initial design stage

    Directory of Open Access Journals (Sweden)

    Dong-Hoon Jeong

    2017-07-01

    Full Text Available Naval ships are assigned many and varied missions. Their performance is critical for mission success, and depends on the specifications of the components. This is why performance analyses of naval ships are required at the initial design stage. Since the design and construction of naval ships take a very long time and incurs a huge cost, Modeling and Simulation (M & S is an effective method for performance analyses. Thus in this study, a simulation core is proposed to analyze the performance of naval ships considering their specifications. This simulation core can perform the engineering level of simulations, considering the mathematical models for naval ships, such as maneuvering equations and passive sonar equations. Also, the simulation models of the simulation core follow Discrete EVent system Specification (DEVS and Discrete Time System Specification (DTSS formalisms, so that simulations can progress over discrete events and discrete times. In addition, applying DEVS and DTSS formalisms makes the structure of simulation models flexible and reusable. To verify the applicability of this simulation core, such a simulation core was applied to simulations for the performance analyses of a submarine in an Anti-SUrface Warfare (ASUW mission. These simulations were composed of two scenarios. The first scenario of submarine diving carried out maneuvering performance analysis by analyzing the pitch angle variation and depth variation of the submarine over time. The second scenario of submarine detection carried out detection performance analysis by analyzing how well the sonar of the submarine resolves adjacent targets. The results of these simulations ensure that the simulation core of this study could be applied to the performance analyses of naval ships considering their specifications.

  10. Idaho National Engineering Laboratory High-Level Waste Roadmap. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-01

    The Idaho National Engineering Laboratory (INEL) High-Level Waste (HLW) Roadmap takes a strategic look at the entire HLW life-cycle starting with generation, through interim storage, treatment and processing, transportation, and on to final disposal. The roadmap is an issue-based planning approach that compares ``where we are now`` to ``where we want and need to be.`` The INEL has been effectively managing HLW for the last 30 years. Calcining operations are continuing to turn liquid HLW into a more manageable form. Although this document recognizes problems concerning HLW at the INEL, there is no imminent risk to the public or environment. By analyzing the INEL current business operations, pertinent laws and regulations, and committed milestones, the INEL HLW Roadmap has identified eight key issues existing at the INEL that must be resolved in order to reach long-term objectives. These issues are as follows: A. The US Department of Energy (DOE) needs a consistent policy for HLW generation, handling, treatment, storage, and disposal. B. The capability for final disposal of HLW does not exist. C. Adequate processes have not been developed or implemented for immobilization and disposal of INEL HLW. D. HLW storage at the INEL is not adequate in terms of capacity and regulatory requirements. E. Waste streams are generated with limited consideration for waste minimization. F. HLW is not adequately characterized for disposal nor, in some cases, for storage. G. Research and development of all process options for INEL HLW treatment and disposal are not being adequately pursued due to resource limitations. H. HLW transportation methods are not selected or implemented. A root-cause analysis uncovered the underlying causes of each of these issues.

  11. System-Level Development of Fault-Tolerant Distributed Aero-Engine Control Architecture, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — NASA's vision for an "intelligent engine" will be realized with the development of a truly distributed control system and reliable smart transducer node components;...

  12. Engineering Electromagnetics

    International Nuclear Information System (INIS)

    Kim, Se Yun

    2009-01-01

    This book deals with engineering electromagnetics. It contains seven chapters, which treats understanding of engineering electromagnetics such as magnet and electron spin, current and a magnetic field and an electromagnetic wave, Essential tool for engineering electromagnetics on rector and scalar, rectangular coordinate system and curl vector, electrostatic field with coulomb rule and method of electric images, Biot-Savart law, Ampere law and magnetic force, Maxwell equation and an electromagnetic wave and reflection and penetration of electromagnetic plane wave.

  13. Identifying and engineering promoters for high level and sustainable therapeutic recombinant protein production in cultured mammalian cells.

    Science.gov (United States)

    Ho, Steven C L; Yang, Yuansheng

    2014-08-01

    Promoters are essential on plasmid vectors to initiate transcription of the transgenes when generating therapeutic recombinant proteins expressing mammalian cell lines. High and sustained levels of gene expression are desired during therapeutic protein production while gene expression is useful for cell engineering. As many finely controlled promoters exhibit cell and product specificity, new promoters need to be identified, optimized and carefully evaluated before use. Suitable promoters can be identified using techniques ranging from simple molecular biology methods to modern high-throughput omics screenings. Promoter engineering is often required after identification to either obtain high and sustained expression or to provide a wider range of gene expression. This review discusses some of the available methods to identify and engineer promoters for therapeutic recombinant protein expression in mammalian cells.

  14. Master’s degree in Nuclear Engineering UPC-ENDESA. Creating synergy at industrial and academic levels

    Energy Technology Data Exchange (ETDEWEB)

    Batet, I.; Calviño, F.; Duch, M.A.; Dies, J.; León, P.; Fernández-Olano, P.

    2015-07-01

    The Master’s degree in Nuclear Engineering, born from the alignment of objectives of Academy and Industry, aims to prepare competent engineers to assume managerial positions within the Nuclear Industry. MNE is completely taught in English. Synergies are established at both industrial and academic levels. MNE syllabus has been designed (and is being continuously improved) with the help of industrial partners and the Spanish Regulatory Body (CSN). One half of the lectures are delivered by professionals external to the university. Besides ENDESA, other companies (ANAV, AREVA, ENRESA, ENSA, ENUSA, IDOM, Nuclenor, Tecnatom, Westinghouse) collaborate in the master. Lecturers from CSN and CIEMAT (the major Spanish research centre) participate in the Master as well. A large portion of the master contents is delivered as Project Based Learning, In general, active learning and team work activities are thoroughly used so as to help the students achieve the learning objectives and acquire a number of soft skills required by industry. MNE is embedded in EMINE, the European Master in Nuclear Energy (European Institute of Technology, KIC-InnoEnergy). As well, MNE is part of a double degree in the Barcelona Engineering School (ETSEIB) with the official Master in Industrial Engineering (MUEI). Having in the same classroom EMINE and MNE students creates a good working atmosphere, while allowing the future engineers work in a multicultural and international environment. The double degree MNE-MUEI allows students to acquire the MNE competencies and, at the same time, legal engineering attributions. It has been useful to attract good engineering students to the master. (Author)

  15. Altered Levels of Aroma and Volatiles by Metabolic Engineering of Shikimate Pathway Genes in Tomato Fruits

    Directory of Open Access Journals (Sweden)

    Vered Tzin

    2015-06-01

    Full Text Available The tomato (Solanum lycopersicum fruit is an excellent source of antioxidants, dietary fibers, minerals and vitamins and therefore has been referred to as a “functional food”. Ripe tomato fruits produce a large number of specialized metabolites including volatile organic compounds. These volatiles serve as key components of the tomato fruit flavor, participate in plant pathogen and herbivore defense, and are used to attract seed dispersers. A major class of specialized metabolites is derived from the shikimate pathway followed by aromatic amino acid biosynthesis of phenylalanine, tyrosine and tryptophan. We attempted to modify tomato fruit flavor by overexpressing key regulatory genes in the shikimate pathway. Bacterial genes encoding feedback-insensitive variants of 3-Deoxy-D-Arabino-Heptulosonate 7-Phosphate Synthase (DAHPS; AroG209-9 and bi-functional Chorismate Mutase/Prephenate Dehydratase (CM/PDT; PheA12 were expressed under the control of a fruit-specific promoter. We crossed these transgenes to generate tomato plants expressing both the AroG209 and PheA12 genes. Overexpression of the AroG209-9 gene had a dramatic effect on the overall metabolic profile of the fruit, including enhanced levels of multiple volatile and non-volatile metabolites. In contrast, the PheA12 overexpression line exhibited minor metabolic effects compared to the wild type fruit. Co-expression of both the AroG209-9 and PheA12 genes in tomato resulted overall in a similar metabolic effect to that of expressing only the AroG209-9 gene. However, the aroma ranking attributes of the tomato fruits from PheA12//AroG209-9 were unique and different from those of the lines expressing a single gene, suggesting a contribution of the PheA12 gene to the overall metabolic profile. We suggest that expression of bacterial genes encoding feedback-insensitive enzymes of the shikimate pathway in tomato fruits provides a useful metabolic engineering tool for the modification of

  16. Mixed and Low-Level Treatment Facility Project. Appendix B, Waste stream engineering files, Part 1, Mixed waste streams

    Energy Technology Data Exchange (ETDEWEB)

    1992-04-01

    This appendix contains the mixed and low-level waste engineering design files (EDFS) documenting each low-level and mixed waste stream investigated during preengineering studies for Mixed and Low-Level Waste Treatment Facility Project. The EDFs provide background information on mixed and low-level waste generated at the Idaho National Engineering Laboratory. They identify, characterize, and provide treatment strategies for the waste streams. Mixed waste is waste containing both radioactive and hazardous components as defined by the Atomic Energy Act and the Resource Conservation and Recovery Act, respectively. Low-level waste is waste that contains radioactivity and is not classified as high-level waste, transuranic waste, spent nuclear fuel, or 11e(2) byproduct material as defined by DOE 5820.2A. Test specimens of fissionable material irradiated for research and development only, and not for the production of power or plutonium, may be classified as low-level waste, provided the concentration of transuranic is less than 100 nCi/g. This appendix is a tool that clarifies presentation format for the EDFS. The EDFs contain waste stream characterization data and potential treatment strategies that will facilitate system tradeoff studies and conceptual design development. A total of 43 mixed waste and 55 low-level waste EDFs are provided.

  17. Groundwork: An Intermediate-Level Text of ESL for Petroleum Engineers, Geologists, and Geophysicists.

    Science.gov (United States)

    Kellersberger, Gail; Rippert-Davila, Susan

    The negotiation, development, testing, and publishing of a specialized text for instructing Chinese geologists and petroleum engineers in English as a second language are chronicled. Aspects of the process discussed include the initial contact and oral agreement with the corporate representative who had requested the training materials, scheduling…

  18. Transportation Engineering Education and Outreach Program Designed for the Collegiate Level. Final Report.

    Science.gov (United States)

    Kuhn, Beverly T.

    The Transportation Engineering Education and Outreach Program was organized to develop and disseminate educational and outreach materials that would encourage students in colleges, universities, and technical schools to select transportation as a career path and to attract more students into transportation graduate programs. The research…

  19. Improving Students’ Learning in Software Engineering Education through Multi-Level Assignments

    NARCIS (Netherlands)

    Dr. Leo Pruijt; Christian Köppe

    2014-01-01

    Author supplied: DOI : http://dx.doi.org/10.1145/2691352.2691357 Assignments and exercises are an essential part of software engineering education. It usually requires a variety of these assignments to cover a desired wide range of educational objectives as defined in the revised Bloom's taxonomy.

  20. Nonmetallic engineered barriers, their properties and role in a geologic repository for high level radioactive waste

    International Nuclear Information System (INIS)

    Lisy, F.

    1994-01-01

    The efficiency of engineered barrier systems depends to a great extent on the properties of the materials used. Backfill and sealing materials must fulfill certain requirements and criteria. They must feature low hydraulic conductivity, high retardation capacity, extremely good sorption properties for a wide range of radionuclides potentially leachable from the deposited waste, low permeability, good compatibility with engineered and natural barriers, good workability, and availability in the necessary quantity and at a reasonable price. Some basic properties are presented of materials which fulfill, to a considerable degree, these requirements and which are thus suggested as suitable backfills, sealings of buffers, namely clay- and cement-based materials (concretes, mortars, etc.). A brief information is also given on some other materials like bitumen, asphalt, etc. (Z.S.) 4 refs

  1. NRC's geotechnical engineering research needs for the high-level waste repository program

    International Nuclear Information System (INIS)

    Gupta, D.C.; Philip, J.; Lorig, L.J.; Chowdhury, A.H.

    1992-01-01

    To develop the capability for independently assessing the US Department of Energy's (DOE's) geologic repository design within a limited time, the US Nuclear Regulatory Commission (NRC) staff needs to perform certain research well before receiving the license application. The NRC staff is using a number of factors to identify the areas that it needs to research. The staff assigns priorities to the needed research based on programmatic considerations and the significance of the work. In the geotechnical engineering field, the staff is conducting research in the following three areas: response of the repository to repeated strong ground motion, rock-mass sealing, and coupled thermo-hydro-mechanical interactions. In this paper, the NRC staff also presents the areas of additional research needed in the geotechnical engineering field

  2. Development of an engineering level prediction method for high angle of attack aerodynamics

    Science.gov (United States)

    Reisenthel, Patrick H.; Rodman, Laura C.; Nixon, David

    1993-01-01

    The present work is concerned with predicting the unsteady flow considered to be the cause of the structural failure of twin vertical tail aircraft. An engineering tool has been produced for high angle of attack aerodynamics using the simplest physical models. The main innovation behind this work is its emphasis on the modeling of two key aspects of the dominant physics associated with high angle-of-attack airflows, namely unsteady separation and vortex breakdown.

  3. A study of diverse clinical decision support rule authoring environments and requirements for integration

    Directory of Open Access Journals (Sweden)

    Zhou Li

    2012-11-01

    Full Text Available Abstract Background Efficient rule authoring tools are critical to allow clinical Knowledge Engineers (KEs, Software Engineers (SEs, and Subject Matter Experts (SMEs to convert medical knowledge into machine executable clinical decision support rules. The goal of this analysis was to identify the critical success factors and challenges of a fully functioning Rule Authoring Environment (RAE in order to define requirements for a scalable, comprehensive tool to manage enterprise level rules. Methods The authors evaluated RAEs in active use across Partners Healthcare, including enterprise wide, ambulatory only, and system specific tools, with a focus on rule editors for reminder and medication rules. We conducted meetings with users of these RAEs to discuss their general experience and perceived advantages and limitations of these tools. Results While the overall rule authoring process is similar across the 10 separate RAEs, the system capabilities and architecture vary widely. Most current RAEs limit the ability of the clinical decision support (CDS interventions to be standardized, sharable, interoperable, and extensible. No existing system meets all requirements defined by knowledge management users. Conclusions A successful, scalable, integrated rule authoring environment will need to support a number of key requirements and functions in the areas of knowledge representation, metadata, terminology, authoring collaboration, user interface, integration with electronic health record (EHR systems, testing, and reporting.

  4. Level Recession Of Emissions Release By Motor-And-Tractor Diesel Engines Through The Application Of Water-Fuel Emulsions

    Science.gov (United States)

    Ivanov, A.; Chikishev, E.

    2017-01-01

    The paper is dedicated to a problem of environmental pollution by emissions of hazardous substances with the exhaust gases of internal combustion engines. It is found that application of water-fuel emulsions yields the best results in diesels where production of a qualitative carburetion is the main problem for the organization of working process. During pilot studies the composition of a water-fuel emulsion with the patent held is developed. The developed composition of a water-fuel emulsion provides its stability within 14-18 months depending on mass content of components in it while stability of emulsions’ analogues makes 8-12 months. The mode of operation of pilot unit is described. Methodology and results of pilot study of operation of diesel engine on a water-fuel emulsion are presented. Cutting time of droplet combustion of a water-fuel emulsion improves combustion efficiency and reduces carbon deposition (varnish) on working surfaces. Partial dismantling of the engine after its operating time during 60 engine hours has shown that there is a removal of a carbon deposition in cylinder-piston group which can be observed visually. It is found that for steady operation of the diesel and ensuring decrease in level of emission of hazardous substances the water-fuel emulsion with water concentration of 18-20% is optimal.

  5. Level of information about gynaecological prevention in teenagers at risk from social exclusion, referred by family court rulings to juvenile attendance centres – a pilot study

    Directory of Open Access Journals (Sweden)

    Marcin Bobiński

    2015-09-01

    Full Text Available Introduction and objective. The objective of the study was to present preliminary results of a pilot study concerning the level of knowledge of gynaecological prevention, conducted in teenagers referred by court rulings to a juvenile attendance centre. Materials and method. The instrument was an anonymous survey questionnaire completed by participants in health prevention classes in late 2010 and early 2011. The studied group consisted of teenagers aged 15–17 years (mean age: 15.72 years, median = 16 years, SD = 0.679 who were under probation officers’ supervision in the Zamość region of south-eastern Poland. The sample size was 101 persons – 51 boys (50.50%, 50 girls (49.5%. Results. According to the respondents, the most important reasons for seeing a gynaecologist were: menstrual disorders (70.30%, suspicion of pregnancy (63.37% and pain or burning sensations while urinating (58.42%. The following were regarded as prevalent cancers in women: cancers of the breast (99.01%, cervix (89.1%, and ovaries (62.38%. Over 92% of subjects stated that it was possible to protect oneself from cervical cancer, but only 41.5% of respondents indicated the correct definition of the term ‘cytology’. Statistical analysis focused on differences between genders. A higher self-assessment of mental health was shown in boys. Conclusions. Teenagers of similar background may find it more difficult to gain access to knowledge about health prophylaxis, including gynaecological prevention. Efforts should be intensified in order to ‘equalize health opportunities’ through appropriate preparation of teaching curricula (including health education and philosophy of medicine.

  6. Global emergency medicine journal club: a social media discussion about the Age-Adjusted D-Dimer Cutoff Levels To Rule Out Pulmonary Embolism trial.

    Science.gov (United States)

    Rezaie, Salim R; Swaminathan, Anand; Chan, Teresa; Shaikh, Sam; Lin, Michelle

    2015-05-01

    Annals of Emergency Medicine collaborated with an educational Web site, Academic Life in Emergency Medicine (ALiEM), to host an online discussion session featuring the 2014 Journal of the American Medical Association publication on the Age-Adjusted D-Dimer Cutoff Levels to Rule Out Pulmonary Embolism (ADJUST-PE) trial by Righini et al. The objective is to describe a 14-day (August 25 to September 7, 2014) worldwide academic dialogue among clinicians in regard to 4 preselected questions about the age-adjusted D-dimer cutoff to detect pulmonary embolism. Five online facilitators hosted the multimodal discussion on the ALiEM Web site, Twitter, and Google Hangout. Comments across the social media platforms were curated for this report, as framed by the 4 preselected questions, and engagement was tracked through various Web analytic tools. Blog and Twitter comments, as well as video expert commentary involving the ADJUST-PE trial, are summarized. The dialogue resulted in 1,169 page views from 391 cities in 52 countries on the ALiEM Web site, 502,485 Twitter impressions, and 159 views of the video interview with experts. A postdiscussion summary on the Journal Jam podcast resulted in 3,962 downloads in its first week of publication during September 16 to 23, 2014. Common themes that arose in the multimodal discussions included the heterogeneity of practices, D-dimer assays, provider knowledge about these assays, and prevalence rates in different areas of the world. This educational approach using social media technologies demonstrates a free, asynchronous means to engage a worldwide audience in scholarly discourse. Copyright © 2015 American College of Emergency Physicians. Published by Elsevier Inc. All rights reserved.

  7. Requirements for high level models supporting design space exploration in model-based systems engineering

    NARCIS (Netherlands)

    Haveman, Steven; Bonnema, Gerrit Maarten

    2013-01-01

    Most formal models are used in detailed design and focus on a single domain. Few effective approaches exist that can effectively tie these lower level models to a high level system model during design space exploration. This complicates the validation of high level system requirements during

  8. Rules of Deception

    DEFF Research Database (Denmark)

    Juhlin, Jonas

    In all wars, deception has been an important element for the military planners, on both the tactical level and the operational level. The good, effective deception operation is of great risk of conflicting with the current Laws of Armed Conflicts, which will be of great concern for the deception ......, the paper will discuss how the inclusion of mission specific rules of deception can greatly help define the boundaries, and give necessary guide lines for conducting deception operations within the laws of armed conflict....

  9. A Regression Study of Salary Determinants in Indian Job Markets for Entry Level Engineering Graduates

    OpenAIRE

    Singh, Rajveer

    2016-01-01

    The economic liberalisation of Indian markets in early 90s boosted the economic growth of the nation in various sectors over the next two decades. One such sector that has seen a massive growth in this time is Information Technology (IT). The IT industry has played a very crucial role in transforming India from a slow moving economy to one of the largest exporters of IT services. This growth created a huge demand in the labour markets for skilled labour, which in turn made engineering one of ...

  10. Fuel Tests on an I-16 Jet-Propulsion Engine at Static Sea-Level Conditions

    Science.gov (United States)

    1947-04-29

    All fuel lines and manometer leads were Joined to tbs engine by r.;bber-hoee con::&-:tions to prov-.de flexi- bility. The test cell Itself wa3 a...The air leakage into t:.e cell was measured i:id laolntefl’ In the calculations of the air flow to the er.jine. Figure 1 also shirks tbfl...t t - ’ > / J / i / 4» / / / >•• —* / - - iw r—’ 860 <•— 4 f < Hot-« el4 oct.nt t> Unil rucl . - -Theoretical lln«i / 0 ; I T

  11. AN ANALYSIS OF THE THERMAL AND MECHANICAL BEHAVIOR OF ENGINEERED BARRIERS IN A HIGH-LEVEL RADIOACTIVE WASTE REPOSITORY

    Directory of Open Access Journals (Sweden)

    S. KWON

    2013-02-01

    Full Text Available Adequate design of engineered barriers, including canister, buffer and backfill, is important for the safe disposal of high-level radioactive waste. Three-dimensional computer simulations were carried out under different condition to examine the thermal and mechanical behavior of engineered barriers and rock mass. The research looked at five areas of importance, the effect of the swelling pressure, water content of buffer, density of compacted bentonite, emplacement type and the selection of failure criteria. The results highlighted the need to consider tensile stress in the outer shell of a canister due to thermal expansion of the canister and the swelling pressure from the buffer for a more reliable design of an underground repository system. In addition, an adequate failure criterion should be used for the buffer and backfill.

  12. An analysis of the thermal and mechanical behavior of engineered barriers in a high-level radioactive waste repository

    International Nuclear Information System (INIS)

    Kwon, S.; Cho, W. J.; Lee, J. O.

    2013-01-01

    Adequate design of engineered barriers, including canister, buffer and backfill, is important for the safe disposal of high level radioactive waste. Three-dimensional computer simulations were carried out under different condition to examine the thermal and mechanical behavior of engineered barriers and rock mass. The research looked at five areas of importance, the effect of the swelling pressure, water content of buffer, density of compacted bentonite, emplacement type and the selection of failure criteria. The results highlighted the need to consider tensile stress in the outer shell of a canister due to thermal expansion of the canister and the swelling pressure from the buffer for a more reliable design of an underground repository system. In addition, an adequate failure criterion should be used for the buffer and backfill.

  13. Fully engineered shallow trench design concepts for disposal of low and intermediate level radioactive waste

    International Nuclear Information System (INIS)

    Locke, J.

    1984-09-01

    In this report, the results of the reviews of design concepts, waste arisings and release mechanisms are described. The basic principles of radiological protection and the proposed strategy for land disposal in the UK are outlined. The essential features of engineered trenches are described with some discussion of the likely material choices and their influence on nuclide release. The radiological protection criteria adopted in this study is that the overall risk of serious health effects arising from any release of radioactivity from a shallow engineered trench should always be less than 10 -6 per annum, which corresponds to a received dose of 0.1 mSv/yr. This approach to radiological protection takes account of the two components of risk of health detriment to future generations; namely the probability that a release of radionuclides will occur and the probability that the subsequent radiation doses will give rise to deleterious effects. A compilation is presented of the waste streams and expected volumes and activities that may be designated for LAND 2 disposal and an initial estimate of the associated nuclide inventory is given. (author)

  14. Does Modern Ideology of Earthquake Engineering Ensure the Declared Levels of Damage of Structures at Earthquakes?

    International Nuclear Information System (INIS)

    Gabrichidze, G.

    2011-01-01

    The basic position of the modern ideology of earthquake engineering is based on the idea that a structure should be designed so that it suffers almost no damage at an earthquake, the occurrence of which is most probable in the given area during the lifetime of the structure. This statement is essentially based on the so-called Performance Based Design, the ideology of the 21 s t century. In the article at tenton is focused on the fact that the modern ideology of earthquake engineering assigns structures to a dangerous zone in which their behavior is defined by processes of damage and destruction of materials, which is a nonequilibrium process and demands application of special refined methods of research. In such conditions use of ratios that correspond to static conditions of loading to describe the process of damage of materials appears to be unfounded. The article raises the question of the necessity of working out a new mathematical model of behavior of materials and structures at rapid intensive impact. (authors)

  15. Exergy and Energy Analysis of Combustion of Blended Levels of Biodiesel, Ethanol and Diesel Fuel in a DI Diesel Engine

    International Nuclear Information System (INIS)

    Khoobbakht, Golmohammad; Akram, A.; Karimi, Mahmoud; Najafi, G.

    2016-01-01

    Highlights: • Exergy analysis showed that thermal efficiency of diesel engine was 36.61%. • Energy loss and work output rates were 71.36 kW and 41.22 kW, respectively. • Exergy efficiency increased with increasing engine load and speed. • Exergy efficiency increased with increasing biodiesel and bioethanol. • 0.17 L of biodiesel, 0.08 L of ethanol in 1 L of diesel at 1900 rpm and 94% load had maximum exergy efficiency. - Abstract: In this study, the first and second laws of thermodynamics are employed to analyze the energy and energy in a four-cylinder, direct injection diesel engine using blended levels of biodiesel and ethanol in diesel fuel. Also investigated the effect of operating factors of engine load and speed as well as blended levels of biodiesel and ethanol in diesel fuel on the exergy efficiency. The experiments were designed using a statistical tool known as Design of Experiments (DoE) based on central composite rotatable design (CCRD) of response surface methodology (RSM). The resultant quadratic models of the response surface methodology were helpful to predict the response parameter (exergy efficiency) further to identify the significant interactions between the input factors on the responses. The results depicted that the exergy efficiency decreased with increasing percent by volume biodiesel and ethanol fuel. The fuel blend of 0.17 L biodiesel and 0.08 L of ethanol added to 1 L of diesel (equivalent with D80B14E6) at 1900 rpm and 94% load was realized have the most exergy efficiency. The results of energy and exergy analyses showed that 43.09% of fuel exergy was destructed and the average thermal efficiency was approximately 36.61%, and the exergetic efficiency was approximately 33.81%.

  16. Rules of thumb and simplified methods

    International Nuclear Information System (INIS)

    Lahti, G.P.

    1985-01-01

    The author points out the value of a thorough grounding in fundamental physics combined with experience of applied practice when using simplified methods and rules of thumb in shield engineering. Present-day quality assurance procedures and good engineering practices require careful documentation of all calculations. The aforementioned knowledge of rules of thumb and back-of-the-envelope calculations can assure both the preparer and the reviewer that the results in the quality assurance documentation are the physically correct ones

  17. Preliminary siting criteria for the proposed mixed and low-level waste treatment facility at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Jorgenson-Waters, M.

    1992-09-01

    The Mixed and Low-Level Waste Treatment Facility project was established in 1991 by the US Department of Energy Idaho Field Office. This facility will provide treatment capabilities for Idaho National Engineering Laboratory (INEL) low-level mixed waste and low-level waste. This report identifies the siting requirements imposed on facilities that treat and store these waste types by Federal and State regulatory agencies and the US Department of Energy. Site selection criteria based on cost, environmental, health and safety, archeological, geological and service, and support requirements are presented. These criteria will be used to recommend alternative sites for the new facility. The National Environmental Policy Act process will then be invoked to evaluate the alternatives and the alternative sites and make a final site determination

  18. 77 FR 15250 - Value Engineering

    Science.gov (United States)

    2012-03-15

    ...-2011-0046] RIN 2125-AF40 Value Engineering AGENCY: Federal Highway Administration (FHWA), DOT. ACTION: Final rule. SUMMARY: This rule updates regulations to enhance the integration of value engineering (VE... Office of Management and Budget (OMB) Circular A-131 on Value Engineering. These revisions also will...

  19. Simulation and Empirical Studies of the Commercial SI Engine Performance and Its Emission Levels When Running on a CNG and Hydrogen Blend

    Directory of Open Access Journals (Sweden)

    Rafaa Saaidia

    2017-12-01

    Full Text Available This article is a report on a simulation based on Computational Fluid Dynamics (CFD and an empirical investigation of in-cylinder flow characteristics, In addition, it assesses the performance and emission levels of a commercial-spark ignited engine running on a CNG and Hydrogen blend in different ratios. The main objective was to determine the optimum hydrogen ratio that would yield the best brake torque and release the least polluting gases. The in-cylinder flow velocity and turbulence aspects were investigated during the intake stroke in order to analyze the intake flow behavior. To reach this goal, a 3D CFD code was adopted. For various engine speeds were investigated for gasoline, CNG and hydrogen and CNG blend (HCNG fueled engines via external mixtures. The variation of brake torque (BT, NOX and CO emissions. A series of tests were conducted on the engine within the speed range of 1000 to 5000 rpm. For this purpose, a commercial Hyundai Sonata S.I engine was modified to operate with a blend of CNG and Hydrogen in different ratios. The experiments attempted to determine the optimum allowable hydrogen ratio with CNG for normal engine operation. The engine performance and the emission levels were also analyzed. At the engine speed of 4200 rpm, the results revealed that beyond a ratio of 50% of the volume of hydrogen added to CNG a backfire phenomenon appeared. Below this ratio (0~40% of the hydrogen volume, the CNG and Hydrogen blend seemed to be beneficial for the engine performance and for curtailing the emission level. However, at low engine speeds, the NOX concentration increased simultaneously with hydrogen content. In contrast, at high engine speeds, the NOX concentration decreased to its lowest level compared to that reached with gasoline as a running fuel. The concentration levels of HC, CO2, and CO decreased with the increase of hydrogen percentage.

  20. Preliminary Waste Form Compliance Plan for the Idaho National Engineering and Environmental Laboratory High-Level Waste

    International Nuclear Information System (INIS)

    Staples, B. A.; O'Holleran, T. P.

    1999-01-01

    The Department of Energy (DOE) has specific technical and documentation requirements for high-level waste (HLW) that is to be placed in a federal repository. This document describes in general terms the strategy to be used at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that vitrified HLW, if produced at the INEEL, meets these requirements. Waste form, canister, quality assurance, and documentation specifications are discussed. Compliance strategy is given, followed by an overview of how this strategy would be implemented for each specification

  1. Preliminary Waste Form Compliance Plan for the Idaho National Engineering and Environmental Laboratory High-Level Waste

    Energy Technology Data Exchange (ETDEWEB)

    B. A. Staples; T. P. O' Holleran

    1999-05-01

    The Department of Energy (DOE) has specific technical and documentation requirements for high-level waste (HLW) that is to be placed in a federal repository. This document describes in general terms the strategy to be used at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that vitrified HLW, if produced at the INEEL, meets these requirements. Waste form, canister, quality assurance, and documentation specifications are discussed. Compliance strategy is given, followed by an overview of how this strategy would be implemented for each specification.

  2. Engineering gravimetric monitoring methods to cope with excessively high dust levels-2.

    CSIR Research Space (South Africa)

    Belle, BK

    1999-11-01

    Full Text Available -test and F-test), the mean dust concentration measured by pairs of cyclones is not significantly affected at 95 percent level of confidence. In other words, there is no difference between the measured mean dust concentration levels between various sampler... List of Figures . . . . . . . 8 List of Tables . . . .. . . 11 Glossary of Abbreviations and Symbols . . . . . 12 Acknowledgements . . . . . . . . 13 1 Introduction . . . . . . . 14 2 Background . . . . . . . 14 3 Test Samplers . . . . . . . 16...

  3. Increased levels of etheno-DNA adducts and genotoxicity biomarkers of long-term exposure to pure diesel engine exhaust.

    Science.gov (United States)

    Shen, Meili; Bin, Ping; Li, Haibin; Zhang, Xiao; Sun, Xin; Duan, Huawei; Niu, Yong; Meng, Tao; Dai, Yufei; Gao, Weimin; Yu, Shanfa; Gu, Guizhen; Zheng, Yuxin

    2016-02-01

    Etheno-DNA adducts are biomarkers for assessing oxidative stress. In this study, the aim was to detect the level of etheno-DNA adducts and explore the relationship between the etheno-DNA adducts and genotoxicity biomarkers of the diesel engine exhaust (DEE)-exposed workers. We recruited 86 diesel engine testing workers with long-term exposure to DEE and 99 non-DEE-exposed workers. The urinary mono-hydroxylated polycyclic aromatic hydrocarbons (OH-PAHs) and etheno-DNA adducts (εdA and εdC) were detected by HPLC-MS/MS and UPLC-MS/MS, respectively. Genotoxicity biomarkers were also evaluated by comet assay and cytokinesis-block micronucleus assay. The results showed that urinary εdA was significantly higher in the DEE-exposed workers (p<0.001), exhibited 2.1-fold increase compared with the non-DEE-exposed workers. The levels of urinary OH-PAHs were positively correlated with the level of εdA among all the study subjects (p<0.001). Moreover, we found that the increasing level of εdA was significantly associated with the increased olive tail moment, percentage of tail DNA, or frequency of micronucleus in the study subjects (p<0.01). No significant association was observed between the εdC level and any measured genotoxicity biomarkers. In summary, εdA could serve as an indicator for DEE exposure in the human population. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Engineering properties of high and low altitude rice varieties from Kashmir valley at different processing levels

    Directory of Open Access Journals (Sweden)

    Raees Haq

    2016-12-01

    Full Text Available The knowledge of engineering properties such as gravimetrical properties (1,000 grain mass, bulk density, true density, and porosity, dimensional properties (length, width, thickness, aspect ratio, surface area, geometric mean diameter, and sphericity, frictional properties (angle of repose and coefficient of friction, and aerodynamic properties (drag coefficient and terminal velocity are necessary parameters related to machine design for different agricultural process operations such as handling, harvesting, threshing, cleaning, conveying, sorting, drying, processing, and storage. India is a vast country and contributes 20% of the total world’s rice production with cultivars ranging from the scented long grain ones to the sticky short grains. The Kashmir valley cultivates mainly short–medium bold varieties as temperate conditions in the valley are not suitable for the cultivation of long grain scented basmati rice. The most steps in cultivation and postharvest processing are manual and the aim of this work is to emphasize which variety sustains the processing steps to produce high yield quality rice for strengthening the economic conditions of the people.

  5. Innovative Calibration Method for System Level Simulation Models of Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Ivo Prah

    2016-09-01

    Full Text Available The paper outlines a procedure for the computer-controlled calibration of the combined zero-dimensional (0D and one-dimensional (1D thermodynamic simulation model of a turbocharged internal combustion engine (ICE. The main purpose of the calibration is to determine input parameters of the simulation model in such a way as to achieve the smallest difference between the results of the measurements and the results of the numerical simulations with minimum consumption of the computing time. An innovative calibration methodology is based on a novel interaction between optimization methods and physically based methods of the selected ICE sub-systems. Therein physically based methods were used for steering the division of the integral ICE to several sub-models and for determining parameters of selected components considering their governing equations. Innovative multistage interaction between optimization methods and physically based methods allows, unlike the use of well-established methods that rely only on the optimization techniques, for successful calibration of a large number of input parameters with low time consumption. Therefore, the proposed method is suitable for efficient calibration of simulation models of advanced ICEs.

  6. Study on engineering economics of China high-level radioactive waste geological disposal

    International Nuclear Information System (INIS)

    Qu Jun; Guo Zongzhi; Yang Lirong; Hu Jiang

    2012-01-01

    In this paper, based on the research and analysis about the repository construction cost of the European, US and Japan, together with the concept design pattern of China's high level radioactive waste repository, the preliminary economic analysis of China is presented. Meanwhile, combining with China's nuclear power development layout and picking-up policy of spent fuel fund, the preliminary measurement concerning the capital resource of high level radioactive waste disposal is implemented, which contribute to the conclusion initiatively that the spent fuel fund could meet the need of the financial demand of disposal cost. (authors)

  7. Lysate of engineered Escherichia coli supports high-level conversion of glucose to 2,3-butanediol.

    Science.gov (United States)

    Kay, Jennifer E; Jewett, Michael C

    2015-11-01

    Cell-free metabolic engineering (CFME) is emerging as a powerful approach for the production of target molecules and pathway debugging. Unfortunately, high cofactor costs, limited cofactor and energy regeneration, and low volumetric productivities hamper the widespread use and practical implementation of CFME technology. To address these challenges, we have developed a cell-free system that harnesses ensembles of catalytic proteins prepared from crude lysates, or extracts, of cells to fuel highly active heterologous metabolic conversions. As a model pathway, we selected conversion of glucose to 2,3-butanediol (2,3-BD), a medium level commodity chemical with many industrial applications. Specifically, we engineered a single strain of Escherichia coli to express three pathway enzymes necessary to make meso-2,3-BD (m2,3-BD). We then demonstrated that lysates from this strain, with addition of glucose and catalytic amounts of cofactors NAD+ and ATP, can produce m2,3-BD. Endogenous glycolytic enzymes convert glucose to pyruvate, the starting intermediate for m2,3-BD synthesis. Strikingly, with no strain optimization, we observed a maximal synthesis rate of m2,3-BD of 11.3 ± 0.1 g/L/h with a theoretical yield of 71% (0.36 g m2,3-BD/g glucose) in batch reactions. Titers reached 82 ± 8 g/L m2,3-BD in a 30 h fed-batch reaction. Our results highlight the ability for high-level co-factor regeneration in cell-free lysates. Further, they suggest exciting opportunities to use lysate-based systems to rapidly prototype metabolic pathways and carry out molecular transformations when bioconversion yields (g product/L), productivities (g product/L/h), or cellular toxicity limit commercial feasibility of whole-cell fermentation. Copyright © 2015 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

  8. Engineering of a Bacillus subtilis strain with adjustable levels of intracellular biotin for secretory production of functional streptavidin.

    Science.gov (United States)

    Wu, Sau-Ching; Wong, Sui-Lam

    2002-03-01

    Streptavidin is a biotin-binding protein which has been widely used in many in vitro and in vivo applications. Because of the ease of protein recovery and availability of protease-deficient strains, the Bacillus subtilis expression-secretion system is an attractive system for streptavidin production. However, attempts to produce streptavidin using B. subtilis face the problem that cells overproducing large amounts of streptavidin suffer poor growth, presumably because of biotin deficiency. This problem cannot be solved by supplementing biotin to the culture medium, as this will saturate the biotin binding sites in streptavidin. We addressed this dilemma by engineering a B. subtilis strain (WB800BIO) which overproduces intracellular biotin. The strategy involves replacing the natural regulatory region of the B. subtilis chromosomal biotin biosynthetic operon (bioWAFDBIorf2) with an engineered one consisting of the B. subtilis groE promoter and gluconate operator. Biotin production in WB800BIO is induced by gluconate, and the level of biotin produced can be adjusted by varying the gluconate dosage. A level of gluconate was selected to allow enhanced intracellular production of biotin without getting it released into the culture medium. WB800BIO, when used as a host for streptavidin production, grows healthily in a biotin-limited medium and produces large amounts (35 to 50 mg/liter) of streptavidin, with over 80% of its biotin binding sites available for future applications.

  9. Assessment of Self-Efficacy in Systems Engineering as an Indicator of Competency Level Achievement

    Science.gov (United States)

    2014-06-01

    i.e., students, or entry level employees) towards a common goal (i.e., the desired future state) (Ponton et al. 2001, 247). Robbins , Bradley and...04, MIT Sloan, Cambridge, MA. Lucas, William A., Sarah Y. Cooper, Tony Ward, and Frank Cave. 2009. “Industry Placement, Authentic Experience and

  10. Radiological, physical, and chemical characterization of low-level alpha contaminated wastes stored at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Apel, M.L.; Becker, G.K.; Ragan, Z.K.; Frasure, J.; Raivo, B.D.; Gale, L.G.; Pace, D.P.

    1994-03-01

    This document provides radiological, physical, and chemical characterization data for low-level alpha-contaminated radioactive and low-level alpha-contaminated radioactive and hazardous (i.e., mixed) wastes stored at the Idaho National Engineering Laboratory and considered for treatment under the Private Sector Participation Initiative Program. Waste characterization data are provided in the form of INEL Waste Profile Sheets. These documents provide, for each content code, information on waste identification, waste description, waste storage configuration, physical/chemical waste composition, radionuclide and associated alpha activity waste characterization data, and hazardous constituents present in the waste. Information is provided for 97 waste streams which represent an estimated total volume of 25,450 m 3 corresponding to a total mass of approximately 12,000,000 kg. In addition, considerable information concerning alpha, beta, gamma, and neutron source term data specific to Rocky Flats-generated waste forms stored at the INEL are provided to assist in facility design specification

  11. Radiological, physical, and chemical characterization of low-level alpha contaminated wastes stored at the Idaho National Engineering Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Apel, M.L.; Becker, G.K.; Ragan, Z.K.; Frasure, J.; Raivo, B.D.; Gale, L.G.; Pace, D.P.

    1994-03-01

    This document provides radiological, physical, and chemical characterization data for low-level alpha-contaminated radioactive and low-level alpha-contaminated radioactive and hazardous (i.e., mixed) wastes stored at the Idaho National Engineering Laboratory and considered for treatment under the Private Sector Participation Initiative Program. Waste characterization data are provided in the form of INEL Waste Profile Sheets. These documents provide, for each content code, information on waste identification, waste description, waste storage configuration, physical/chemical waste composition, radionuclide and associated alpha activity waste characterization data, and hazardous constituents present in the waste. Information is provided for 97 waste streams which represent an estimated total volume of 25,450 m 3 corresponding to a total mass of approximately 12,000,000 kg. In addition, considerable information concerning alpha, beta, gamma, and neutron source term data specific to Rocky Flats-generated waste forms stored at the INEL are provided to assist in facility design specification.

  12. Human factors, system safety, and systems engineering in the transportation of U.S. high-level waste

    International Nuclear Information System (INIS)

    Price, D.L.; Chu, S.C.

    1993-01-01

    The U.S. Nuclear Waste Technical Review Board is an independent agency charged with evaluating the technical and scientific validity of the U.S. Department of Energy's program to manage the disposal of spent fuel and defense high-level waste. The Board has continued to emphasize the importance of using a true system approach in designing the waste management system. The Board has recommended the application of basic design disciplines such as human factors, system safety, and systems engineering. A top-level system study needs to be undertaken that focuses on minimizing handling. The analysis must be well done, in a timely manner, and without the inclusion in the analysis of arbitrary and artificial constraints. (author)

  13. Oxytocin modulates trait-based rule following

    NARCIS (Netherlands)

    Gross, J.; de Dreu, C.K.W.

    Rules, whether in the form of norms, taboos or laws, regulate and coordinate human life. Some rules, however, are arbitrary and adhering to them can be personally costly. Rigidly sticking to such rules can be considered maladaptive. Here, we test whether, at the neurobiological level, (mal)adaptive

  14. Biomimetic fabrication of a three-level hierarchical calcium phosphate/collagen/hydroxyapatite scaffold for bone tissue engineering

    International Nuclear Information System (INIS)

    Zhou, Changchun; Ye, Xingjiang; Fan, Yujiang; Tan, Yanfei; Qing, Fangzu; Zhang, Xingdong; Ma, Liang

    2014-01-01

    A three-level hierarchical calcium phosphate/collagen/hydroxyapatite (CaP/Col/HAp) scaffold for bone tissue engineering was developed using biomimetic synthesis. Porous CaP ceramics were first prepared as substrate materials to mimic the porous bone structure. A second-level Col network was then composited into porous CaP ceramics by vacuum infusion. Finally, a third-level HAp layer was achieved by biomimetic mineralization. The three-level hierarchical biomimetic scaffold was characterized using scanning electron microscopy, energy-dispersive x-ray spectra, x-ray diffraction and Fourier transform infrared spectroscopy, and the mechanical properties of the scaffold were evaluated using dynamic mechanical analysis. The results show that this scaffold exhibits a similar structure and composition to natural bone tissues. Furthermore, this three-level hierarchical biomimetic scaffold showed enhanced mechanical strength compared with pure porous CaP scaffolds. The biocompatibility and osteoinductivity of the biomimetic scaffolds were evaluated using in vitro and in vivo tests. Cell culture results indicated the good biocompatibility of this biomimetic scaffold. Faster and increased bone formation was observed in these scaffolds following a six-month implantation in the dorsal muscles of rabbits, indicating that this biomimetic scaffold exhibits better osteoinductivity than common CaP scaffolds. (papers)

  15. [Association of etheno-DNA adduct and DNA methylation level among workers exposed to diesel engine exhaust].

    Science.gov (United States)

    Shen, M L; He, Z N; Zhang, X; Duan, H W; Niu, Y; Bin, P; Ye, M; Meng, T; Dai, Y F; Yu, S F; Chen, W; Zheng, Y X

    2017-06-06

    Objective: To investigate the association between etheno-DNA adduct and the promoter of DNA methylation levels of cyclin dependent kinase inhibitor 2A (P16), Ras association domain family 1 (RASSF1A) and O-6-methylguanine-DNA methyltransferase (MGMT) in workers with occupational exposure to diesel engine exhaust (DEE). Methods: We recruited 124 diesel engine testing workers as DEE exposure group and 112 water pump operator in the same area as control group in Henan province in 2012 using cluster sampling. The demographic data were obtained by questionnaire survey; urine after work and venous blood samples were collected from each subject. The urinary etheno-DNA adducts were detected using UPLC-MS/MS, including 1,N6-etheno-2'-deoxyadenosine (εdA) and 3,N4-etheno-2'-deoxycytidine(εdC). The DNA methylation levels of P16, RASSF1A, and MGMT were evaluated using bisulfite-pyrosequencing assay. The percentage of methylation was expressed as the 5-methylcytosine (5mC) over the sum of cytosines (%5mC). Spearman correlation and multiple linear regression were applied to analyze the association between etheno-DNA adducts and DNA methylation of P16, RASSF1A, and MGMT. Results: The median ( P (25)- P (75)) of urinary εdA level was 230.00 (98.04-470.91) pmol/g creatinine in DEE exposure group, and 102.10 (49.95-194.48) creatinine in control group. The level of εdA was higher in DEE exposure group than control group ( P 0.05) . Multiple linear regression confirmed the negative correlation between εdA and DNA methylation levels of P16, RASSF1A, and MGMT in non-smoking group (β (95 %CI ) was -0.068 (-0.132--0.003), -0.082 (-0.159--0.004) and -0.048 (-0.090--0.007), P values were 0.039, 0.039 and 0.024, respectively). Moreover, εdC was negative associated with DNA methylation level of MGMT in non-smoking group (β (95 %CI ) was -0.094 (-0.179--0.008), P= 0.032). Conclusion: DEE exposure could induce the increased of εdA and decreased of DNA methylation levels of P16, RASSF1A

  16. Low level image processing techniques using the pipeline image processing engine in the flight telerobotic servicer

    Science.gov (United States)

    Nashman, Marilyn; Chaconas, Karen J.

    1988-01-01

    The sensory processing system for the NASA/NBS Standard Reference Model (NASREM) for telerobotic control is described. This control system architecture was adopted by NASA of the Flight Telerobotic Servicer. The control system is hierarchically designed and consists of three parallel systems: task decomposition, world modeling, and sensory processing. The Sensory Processing System is examined, and in particular the image processing hardware and software used to extract features at low levels of sensory processing for tasks representative of those envisioned for the Space Station such as assembly and maintenance are described.

  17. Engineering task plan and status of 241-S-106 Enraf level gauge wire break

    International Nuclear Information System (INIS)

    Moore, T.L.

    1994-09-01

    This report discusses the findings of a task team which was formed which identified the need for short-term actions to re-establish tank waste level monitoring and to permanently address wire failure. The failed wire was removed and sent to Pacific Northwest Laboratory (PNL) for analysis. It was determined that the cause of the wire failure was due to chloride ion stress corrosion cracking (SCC) of the 316 stainless steel (SS) wire. Radiation induced breakdown of the polyvinyl chloride (PVC) riser liners is suspected to be the source of the chloride ions

  18. A paradigm shift in pharmacokinetic-pharmacodynamic (PKPD) modeling: rule of thumb for estimating free drug level in tissue compared with plasma to guide drug design.

    Science.gov (United States)

    Poulin, Patrick

    2015-07-01

    A basic assumption in pharmacokinetics-pharmacodynamics research is that the free drug concentration is similar in plasma and tissue, and, hence, in vitro plasma data can be used to estimate the in vivo condition in tissue. However, in a companion manuscript, it has been demonstrated that this assumption is violated for the ionized drugs. Nonetheless, these observations focus on in vitro static environments and do not challenge data with an in vivo dynamic system. Therefore, an extension from an in vitro to an in vivo system becomes the necessary next step. The objective of this study was to perform theoretical simulations of the free drug concentration in tissue and plasma by using a physiologically based pharmacokinetics (PBPK) model reproducing the in vivo conditions in human. Therefore, the effects of drug ionization, lipophilicity, and clearance have been taken into account in a dynamic system. This modeling exercise was performed as a proof of concept to demonstrate that free drug concentration in tissue and plasma may also differ in a dynamic system for passively permeable drugs that are ionized at the physiological pH. The PBPK model simulations indicated that free drug concentrations in tissue cells and plasma significantly differ for the ionized drugs because of the pH gradient effect between cells and interstitial space. Hence, a rule of thumb for potentially performing more accurate PBPK/PD modeling is suggested, which states that the free drug concentration in tissue and plasma will differ for the ionizable drugs in contrast to the neutral drugs. In addition to the pH gradient effect for the ionizable drugs, lipophilicity and clearance effects will increase or decrease the free drug concentration in tissue and plasma for each class of drugs; thus, higher will be the drug lipophilicity and clearance, lower would be the free drug concentration in plasma, and, hence, in tissue, in a dynamic in vivo system. Therefore, only considering the value of free

  19. System-Level Testing of the Advanced Stirling Radioisotope Generator Engineering Hardware

    Science.gov (United States)

    Chan, Jack; Wiser, Jack; Brown, Greg; Florin, Dominic; Oriti, Salvatore M.

    2014-01-01

    To support future NASA deep space missions, a radioisotope power system utilizing Stirling power conversion technology was under development. This development effort was performed under the joint sponsorship of the Department of Energy and NASA, until its termination at the end of 2013 due to budget constraints. The higher conversion efficiency of the Stirling cycle compared with that of the Radioisotope Thermoelectric Generators (RTGs) used in previous missions (Viking, Pioneer, Voyager, Galileo, Ulysses, Cassini, Pluto New Horizons and Mars Science Laboratory) offers the advantage of a four-fold reduction in Pu-238 fuel, thereby extending its limited domestic supply. As part of closeout activities, system-level testing of flight-like Advanced Stirling Convertors (ASCs) with a flight-like ASC Controller Unit (ACU) was performed in February 2014. This hardware is the most representative of the flight design tested to date. The test fully demonstrates the following ACU and system functionality: system startup; ASC control and operation at nominal and worst-case operating conditions; power rectification; DC output power management throughout nominal and out-of-range host voltage levels; ACU fault management, and system command / telemetry via MIL-STD 1553 bus. This testing shows the viability of such a system for future deep space missions and bolsters confidence in the maturity of the flight design.

  20. Engineering high α-amylase levels in wheat grain lowers Falling Number but improves baking properties.

    Science.gov (United States)

    Ral, Jean-Philippe; Whan, Alex; Larroque, Oscar; Leyne, Emmett; Pritchard, Jeni; Dielen, Anne-Sophie; Howitt, Crispin A; Morell, Matthew K; Newberry, Marcus

    2016-01-01

    Late maturity α-amylase (LMA) and preharvest sprouting (PHS) are genetic defects in wheat. They are both characterized by the expression of specific isoforms of α-amylase in particular genotypes in the grain prior to harvest. The enhanced expression of α-amylase in both LMA and PHS results in a reduction in Falling Number (FN), a test of gel viscosity, and subsequent downgrading of the grain, along with a reduced price for growers. The FN test is unable to distinguish between LMA and PHS; thus, both defects are treated similarly when grain is traded. However, in PHS-affected grains, proteases and other degradative process are activated, and this has been shown to have a negative impact on end product quality. No studies have been conducted to determine whether LMA is detrimental to end product quality. This work demonstrated that wheat in which an isoform α-amylase (TaAmy3) was overexpressed in the endosperm of developing grain to levels of up to 100-fold higher than the wild-type resulted in low FN similar to those seen in LMA- or PHS-affected grains. This increase had no detrimental effect on starch structure, flour composition and enhanced baking quality, in small-scale 10-g baking tests. In these small-scale tests, overexpression of TaAmy3 led to increased loaf volume and Maillard-related browning to levels higher than those in control flours when baking improver was added. These findings raise questions as to the validity of the assumption that (i) LMA is detrimental to end product quality and (ii) a low FN is always indicative of a reduction in quality. This work suggests the need for a better understanding of the impact of elevated expression of specific α-amylase on end product quality. © 2015 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  1. Approaches for establishing human health no effect levels for engineered nanomaterials

    Science.gov (United States)

    Aschberger, K.; Christensen, F. M.

    2011-07-01

    Current Technical Guidance Documents for preparing risk assessments, like the guidance for the implementation of REACH, have limited focus on chemical substances in the particulate form and generally do not focus on substances in the nanoform. Within the ENRHES project a comprehensive and critical scientific review of publicly available health and safety information on four types of nanoparticles was performed. Based on the identified exposure and hazard data, basic human health risk assessment appraisals were carried out for fullerenes, carbon nanotubes, nano-silver and nano-titanium dioxide. These risk assessment appraisals followed the structure of a regulatory risk assessment and if possible and relevant, it was attempted to derive indicative human no-effect levels from key studies by applying assessment factors as suggested in the technical guidance document for REACH. These assessment factors address differences and uncertainty related to exposure features between test animals and humans (time, respiratory volume), other interspecies and intraspecies differences and factors for extrapolation to chronic duration. If required, the severity of effects and the quality of the database can be addressed by additional factors. Recently other procedures for deriving human no-effect levels have been published and these are compared to the ENRHES basic risk assessment appraisals. The main differences were observed in relation to evaluating the differences in animal and human exposure situations and interspecies differences, and in applying assessment factors for intraspecies differences for local effects. The applicability of the REACH guidance for nanomaterials is currently being investigated for possible adaptations, considering the specific behaviour and mode of action of nanomaterials.

  2. Approaches for establishing human health no effect levels for engineered nanomaterials

    International Nuclear Information System (INIS)

    Aschberger, K; Christensen, F M

    2011-01-01

    Current Technical Guidance Documents for preparing risk assessments, like the guidance for the implementation of REACH, have limited focus on chemical substances in the particulate form and generally do not focus on substances in the nanoform. Within the ENRHES project a comprehensive and critical scientific review of publicly available health and safety information on four types of nanoparticles was performed. Based on the identified exposure and hazard data, basic human health risk assessment appraisals were carried out for fullerenes, carbon nanotubes, nano-silver and nano-titanium dioxide. These risk assessment appraisals followed the structure of a regulatory risk assessment and if possible and relevant, it was attempted to derive indicative human no-effect levels from key studies by applying assessment factors as suggested in the technical guidance document for REACH. These assessment factors address differences and uncertainty related to exposure features between test animals and humans (time, respiratory volume), other interspecies and intraspecies differences and factors for extrapolation to chronic duration. If required, the severity of effects and the quality of the database can be addressed by additional factors. Recently other procedures for deriving human no-effect levels have been published and these are compared to the ENRHES basic risk assessment appraisals. The main differences were observed in relation to evaluating the differences in animal and human exposure situations and interspecies differences, and in applying assessment factors for intraspecies differences for local effects. The applicability of the REACH guidance for nanomaterials is currently being investigated for possible adaptations, considering the specific behaviour and mode of action of nanomaterials.

  3. Pilot Study for Maintenance Rule at KSNP

    International Nuclear Information System (INIS)

    Choi, Kwang Hee; Jeong, Hyeon Jong; Jee, Moon Hak; Hong, Sung Yull

    2005-01-01

    Maintenance Rule (MR), which was developed to monitor the effectiveness of maintenance in a nuclear power plant (NPP), has been received as highly successful program by and large since its implementation in 1996 in the United States. Korea has initiated two pilot programs to implement the Maintenance Rule program in 2003. Selected plants for the pilot implementation are Kori 3 and 4 units and Ulchin 3 and 4 units, where Kori 3 and 4 units are Westinghouse units and Ulchin 3 and 4 units are Korean Standardized Nuclear Power (KSNP) Plant units. This paper describes the results of each key tasks completed to date and insights gained from pilot study on the KSNP units. Currently, Scoping of the functions of maintenance rule and determination of safety significance level have been completed during first year. As first task, total 607 functions were identified and defined by detailed function analysis on 135 systems that cover all plant systems. About 55% of total functions are selected as within the scope of maintenance rule. Among these inscoped functions, 56% of scoped functions are safety related and 44% are non-safety related functions. Evaluation of safety significance for each function was determined by expert panel consist of eight experts in field of plant maintenance, operation, PSA, work schedule and system engineers. As a result, about 46% of functions were determined to be high safety significant functions and rest of the functions were classified as low safety significant. The remaining tasks that are included determination of performance criteria and preparation of implementing guideline will be performed in following years

  4. Sum rules for collisional processes

    International Nuclear Information System (INIS)

    Oreg, J.; Goldstein, W.H.; Bar-Shalom, A.; Klapisch, M.

    1991-01-01

    We derive level-to-configuration sum rules for dielectronic capture and for collisional excitation and ionization. These sum rules give the total transition rate from a detailed atomic level to an atomic configuration. For each process, we show that it is possible to factor out the dependence on continuum-electron wave functions. The remaining explicit level dependence of each rate is then obtained from the matrix element of an effective operator acting on the bound orbitals only. In a large class of cases, the effective operator reduces to a one-electron monopole whose matrix element is proportional to the statistical weight of the level. We show that even in these cases, nonstatistical level dependence enters through the dependence of radial integrals on continuum orbitals. For each process, explicit analytic expressions for the level-to-configuration sum rules are given for all possible cases. Together with the well-known J-file sum rule for radiative rates [E. U. Condon and G. H. Shortley, The Theory of Atomic Spectra (University Press, Cambridge, 1935)], the sum rules offer a systematic and efficient procedure for collapsing high-multiplicity configurations into ''effective'' levels for the purpose of modeling the population kinetics of ionized heavy atoms in plasma

  5. Operator algebra from fusion rules

    International Nuclear Information System (INIS)

    Fuchs, J.

    1989-03-01

    It is described how the fusion rules of a conformal field theory can be employed to derive differential equations for the four-point functions of the theory, and thus to determine eventually the operator product coeffients for primary fields. The results are applied to the Ising fusion rules. A set of theories possessing these function rules is found which is labelled by two discrete parameters. For a specific value of one of the parameters, these are the level one Spin(2m+1) Wess-Zusimo-Witten theories; it is shown that they represent an infinite number of inequivalent theories. (author). 38 refs

  6. Geological disposal of high-level radioactive waste and the role of rock engineering

    International Nuclear Information System (INIS)

    Sugihara, Kozo

    2008-01-01

    Japan Atomic Energy Agency (JAEA) and its predecessors have been conducting an extensive geoscientific research program since the 1970's in order to contribute to the formation of a firm scientific and technological basis for the geological disposal of high level radioactive waste in Japan. As a part of this program, in situ experiments have been performed at the Tono Mine in soft sedimentary rocks and at the Kamaishi Mine in hard crystalline rocks. An experiment on excavation disturbance has been one of these experiments and has revealed the extent and properties of the excavation disturbed zone (EDZ) and the applicability of available measurement methods. It is suggested that mechanical excavation and controlled excavation have reduced excavation damage of the rock mass around a drift, although some improvements in the currently available methods for measuring and simulating the EDZ are essential to understand excavation disturbance in more detail. JAEA is now promoting two underground research laboratory projects in Japan; the Mizunami Underground Research Laboratory (MIU) project for crystalline rocks and the Horonobe Underground Research Laboratory (Horonobe URL) project for sedimentary rocks. From a rock mechanical point of view, the major interest in these projects will be paid to failure phenomenon deep underground, rock stress estimation at larger scales and long-term physical stability of underground structure. These projects are open for international collaboration. (author)

  7. Management of scientific and engineering data collected during site characterization of a potential high-level waste repository

    International Nuclear Information System (INIS)

    Newbury, C.M.; Heitland, G.W.

    1992-01-01

    This paper discusses the characterization of Yucca Mountain as a potential site for a high-level nuclear waste repository encompasses many diverse investigations to determine the nature of the site. Laboratory and on-site investigations are being conducted of the geology, hydrology, mineralogy, paleoclimate, geotechnical properties, and past use of the area, to name a few. Effective use of the data from these investigations requires development of a system for the collection, storage, and dissemination of those scientific and engineering data needed to support model development, design, and performance assessment. The time and budgetary constraints associated with this project make sharing of technical data within the geoscience community absolutely critical to the successful solution of the complex scientific problem challenging us

  8. Engineered mutations in fibrillin-1 leading to Marfan syndrome act at the protein, cellular and organismal levels.

    Science.gov (United States)

    Zeyer, Karina A; Reinhardt, Dieter P

    2015-01-01

    Fibrillins are the major components of microfibrils in the extracellular matrix of elastic and non-elastic tissues. They are multi-domain proteins, containing primarily calcium binding epidermal growth factor-like (cbEGF) domains and 8-cysteine/transforming growth factor-beta binding protein-like (TB) domains. Mutations in the fibrillin-1 gene give rise to Marfan syndrome, a connective tissue disorder with clinical complications in the cardiovascular, skeletal, ocular and other organ systems. Here, we review the consequences of engineered Marfan syndrome mutations in fibrillin-1 at the protein, cellular and organismal levels. Representative point mutations associated with Marfan syndrome in affected individuals have been introduced and analyzed in recombinant fibrillin-1 fragments. Those mutations affect fibrillin-1 on a structural and functional level. Mutations which impair folding of cbEGF domains can affect protein trafficking. Protein folding disrupted by some mutations can lead to defective secretion in mutant fibrillin-1 fragments, whereas fragments with other Marfan mutations are secreted normally. Many Marfan mutations render fibrillin-1 more susceptible to proteolysis. There is also evidence that some mutations affect heparin binding. Few mutations have been further analyzed in mouse models. An extensively studied mouse model of Marfan syndrome expresses mouse fibrillin-1 with a missense mutation (p.C1039G). The mice display similar characteristics to human patients with Marfan syndrome. Overall, the analyses of engineered mutations leading to Marfan syndrome provide important insights into the pathogenic molecular mechanisms exerted by mutated fibrillin-1. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Engineering task plan for upgrades to the leveling jacks on core sample trucks number 3 and 4; TOPICAL

    International Nuclear Information System (INIS)

    KOSTELNIK, A.J.

    1999-01-01

    Characterizing the waste in underground storage tanks at the Hanford Site is accomplished by obtaining a representative core sample for analysis. Core sampling is one of the numerous techniques that have been developed for use given the environmental and field conditions at the Hanford Site. Core sampling is currently accomplished using either Push Mode Core Sample Truck No.1 or; Rotary Mode Core Sample Trucks No.2, 3 or 4. Past analysis (WHC 1994) has indicated that the Core Sample Truck (CST) leveling jacks are structurally inadequate when lateral loads are applied. WHC 1994 identifies many areas where failure could occur. All these failures are based on exceeding the allowable stresses listed in the American Institute of Steel Construction (AISC) code. The mode of failure is for the outrigger attachments to the truck frame to fail resulting in dropping of the CST and possible overturning (Ref. Ziada and Hundal, 1996). Out of level deployment of the truck can exceed the code allowable stresses in the structure. Calculations have been performed to establish limits for maintaining the truck level when lifting. The calculations and the associated limits are included in appendix A. The need for future operations of the CSTS is limited. Sampling is expected to be complete in FY-2001. Since there is limited time at risk for continued use of the CSTS with the leveling controls without correcting the structural problems, there are several design changes that could give incremental improvements to the operational safety of the CSTS with limited impact on available operating time. The improvements focus on making the truck easier to control during lifting and leveling. Not all of the tasks identified in this ETP need to be performed. Each task alone can improve the safety. This engineering task plan is the management plan document for implementing the necessary additional structural analysis. Any additional changes to meet requirements of standing orders shall require a

  10. Engineering task plan for the development, fabrication and installation of rotary mode core sample truck grapple hoist box level wind system

    International Nuclear Information System (INIS)

    BOGER, R.M.

    1999-01-01

    This Engineering Task Plan is to design, generate fabrication drawings, fabricate, test, and install the grapple hoist level wind system for Rotary Mode Core Sample Trucks (RMCST) 3 and 4. Deliverables will include generating fabrication drawings, fabrication of one level wind system, updating fabrication drawings as required, and installation of level wind systems on RMCST 3 or 4. The installation of the level wind systems will be done during a preventive maintenance outage

  11. Technology assessment guide for application of engineered sorbent barriers to low-level radioactive waste disposal sites

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Jones, E.O.; Depner, J.P.

    1989-06-01

    An engineered sorbent barrier (ESB) uses sorbent materials (such as activated carbon or natural zeolites) to restrict migration of radionuclides from low-level waste sites. The permeability of the ESB allows moisture to pass while the sorbent material traps or absorbs contaminants. In contrast, waste sites with impermeable barriers could fill with water, especially those waste sites in humid climates. A sorbent barrier can be a simple, effective, and inexpensive method for restricting radionuclide migration. This report provides information and references to be used in assessing the sorbent barrier technology for low-level waste disposal. The ESB assessment is based on sorbent material and soil properties, site conditions, and waste properties and inventories. These data are used to estimate the thickness of the barrier needed to meet all performance requirements for the waste site. This document addresses the following areas: (1) site information required to assess the need and overall performance of a sorbent barrier; (2) selection and testing of sorbent materials and underlying soils; (3) use of radionuclide transport models to estimate the required barrier thickness and long-term performance under a variety of site conditions; (4) general considerations for construction and quality assurance; and (5) cost estimates for applying the barrier. 37 refs., 6 figs., 2 tabs.

  12. Software engineering

    CERN Document Server

    Thorin, Marc

    1985-01-01

    Software Engineering describes the conceptual bases as well as the main methods and rules on computer programming. This book presents software engineering as a coherent and logically built synthesis and makes it possible to properly carry out an application of small or medium difficulty that can later be developed and adapted to more complex cases. This text is comprised of six chapters and begins by introducing the reader to the fundamental notions of entities, actions, and programming. The next two chapters elaborate on the concepts of information and consistency domains and show that a proc

  13. FeynRules - Feynman rules made easy

    OpenAIRE

    Christensen, Neil D.; Duhr, Claude

    2008-01-01

    In this paper we present FeynRules, a new Mathematica package that facilitates the implementation of new particle physics models. After the user implements the basic model information (e.g. particle content, parameters and Lagrangian), FeynRules derives the Feynman rules and stores them in a generic form suitable for translation to any Feynman diagram calculation program. The model can then be translated to the format specific to a particular Feynman diagram calculator via F...

  14. Delayed rule following

    OpenAIRE

    Schmitt, David R.

    2001-01-01

    Although the elements of a fully stated rule (discriminative stimulus [SD], some behavior, and a consequence) can occur nearly contemporaneously with the statement of the rule, there is often a delay between the rule statement and the SD. The effects of this delay on rule following have not been studied in behavior analysis, but they have been investigated in rule-like settings in the areas of prospective memory (remembering to do something in the future) and goal pursuit. Discriminative even...

  15. High Level Waste Tank Farm Replacement Project for the Idaho Chemical Processing Plant at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    1993-06-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0831, for the construction and operation of the High-Level Waste Tank Farm Replacement (HLWTFR) Project for the Idaho Chemical Processing Plant located at the Idaho National Engineering Laboratory (INEL). The HLWTFR Project as originally proposed by the DOE and as analyzed in this EA included: (1) replacement of five high-level liquid waste storage tanks with four new tanks and (2) the upgrading of existing tank relief piping and high-level liquid waste transfer systems. As a result of the April 1992 decision to discontinue the reprocessing of spent nuclear fuel at INEL, DOE believes that it is unlikely that the tank replacement aspect of the project will be needed in the near term. Therefore, DOE is not proposing to proceed with the replacement of the tanks as described in this-EA. The DOE's instant decision involves only the proposed upgrades aspect of the project described in this EA. The upgrades are needed to comply with Resource Conservation and Recovery Act, the Idaho Hazardous Waste Management Act requirements, and the Department's obligations pursuant to the Federal Facilities Compliance Agreement and Consent Order among the Environmental Protection Agency, DOE, and the State of Idaho. The environmental impacts of the proposed upgrades are adequately covered and are bounded by the analysis in this EA. If DOE later proposes to proceed with the tank replacement aspect of the project as described in the EA or as modified, it will undertake appropriate further review pursuant to the National Environmental Policy Act

  16. Transformation of Arden Syntax's medical logic modules into ArdenML for a business rules management system.

    Science.gov (United States)

    Jung, Chai Young; Choi, Jong-Ye; Jeong, Seong Jik; Cho, Kyunghee; Koo, Yong Duk; Bae, Jin Hee; Kim, Sukil

    2016-05-16

    Arden Syntax is a Health Level Seven International (HL7) standard language that is used for representing medical knowledge as logic statements. Arden Syntax Markup Language (ArdenML) is a new representation of Arden Syntax based on XML. Compilers are required to execute medical logic modules (MLMs) in the hospital environment. However, ArdenML may also replace the compiler. The purpose of this study is to demonstrate that MLMs, encoded in ArdenML, can be transformed into a commercial rule engine format through an XSLT stylesheet and made executable in a target system. The target rule engine selected was Blaze Advisor. We developed an XSLT stylesheet to transform MLMs in ArdenML into Structured Rules Language (SRL) in Blaze Advisor, through a comparison of syntax between the two languages. The stylesheet was then refined recursively, by building and applying rules collected from the billing and coding guidelines of the Korean health insurance service. Two nurse coders collected and verified the rules and two information technology (IT) specialists encoded the MLMs and built the XSLT stylesheet. Finally, the stylesheet was validated by importing the MLMs into Blaze Advisor and applying them to claims data. The language comparison revealed that Blaze Advisor requires the declaration of variables with explicit types. We used both integer and real numbers for numeric types in ArdenML. "IF∼THEN" statements and assignment statements in ArdenML become rules in Blaze Advisor. We designed an XSLT stylesheet to solve this issue. In addition, we maintained the order of rule execution in the transformed rules, and added two small programs to support variable declarations and action statements. A total of 1489 rules were reviewed during this study, of which 324 rules were collected. We removed duplicate rules and encoded 241 unique MLMs in ArdenML, which were successfully transformed into SRL and imported to Blaze Advisor via the XSLT stylesheet. When applied to 73

  17. Effects of acoustic treatment on the interior noise levels of a twin-engine propeller aircraft - Experimental flight results and theoretical predictions

    Science.gov (United States)

    Beyer, T. B.; Powell, C. A.; Daniels, E. F.; Pope, L. D.

    1984-01-01

    In-flight noise level measurements were made within two cabin configurations of a general aviation business aircraft. The Fairchild Merlin IVC twin-engine aircraft was tested with bare walls and fiberglass insulation and in an executive trim configuration. Narrow-band and octave format data were subjected to analyses which permitted identification of the blade passage harmonics (BPH). Cabin noise level reductions (insertion losses) due to added insulation varied with position in the cabin, the BPH number, cabin pressure, and engine torque. The measurements were closely predicted using the propeller aircraft interior noise (PAIN) mode.

  18. Engineering students' and faculty perceptions of teaching methods and the level of faculty involvement that promotes academic success

    Science.gov (United States)

    Karpilo, Lacy N.

    Student academic success is a top priority of higher education institutions in the United States and the trend of students leaving school prior to finishing their degree is a serious concern. Accountability has become a large part of university and college ratings and perceived success. Retention is one component of the accountability metrics used by accreditation agencies. In addition, there are an increasing number of states allocating funds based in part on retention (Seidman, 2005). Institutions have created initiatives, programs, and even entire departments to address issues related to student academic success to promote retention. Universities and colleges have responded by focusing on methods to retain and better serve students. Retention and student academic success is a primary concern for high education institutions; however, engineering education has unique retention issues. The National Science Board (2004) reports a significant decline in the number of individuals in the United States who are training to become engineers, despite the fact that the number of jobs that utilize an engineering background continues to increase. Engineering education has responded to academic success issues by changing curriculum and pedagogical methods (Sheppard, 2001). This descriptive study investigates the perception of engineering students and faculty regarding teaching methods and faculty involvement to create a picture of what is occurring in engineering education. The population was the engineering students and faculty of Colorado State University's College of Engineering. Data from this research suggests that engaging teaching methods are not being used as often as research indicates they should and that there is a lack of student-faculty interaction outside of the classroom. This research adds to the breadth of knowledge and understanding of the current environment of engineering education. Furthermore, the data allows engineering educators and other higher

  19. Field studies of engineered barriers for closure of low level radioactive waste landfills at Los Alamos, New Mexico, USA

    International Nuclear Information System (INIS)

    Nyhan, J.W.; Langhorst, G.J.; Martin, C.E.; Martinez, J.L.; Schofield, T.G.

    1993-01-01

    The Los Alamos National Laboratory examined water balance relationships for four different landfill cover designs containing engineered barriers. These field experiments were performed at Los Alamos, New Mexico, USA, in 1.0- by 10.0-m plots with downhill slopes of 5, 10, 15, and 25%. Field measurements of seepage, precipitation, interflow, runoff, and soil water content were collected in each of the 16 plots representing four slopes each with four cover designs: Conventional, EPA, Loam Capillary Barrier and Clay Loam Capillary Barrier. A seepage collection system was installed beneath each cover design to evaluate the influence of slope length on seepage using a series of four metal pans filled with medium gravel that were placed end-to-end in the bottom of each field plot. An automated water flow data logging system was used to collect hourly seepage, interflow and runoff data and consisted of 100 100-liter tanks, each of which was equipped with an ultrasonic liquid-level sensor and a motor-operated ball valve used to drain the tank. Soil water content was routinely monitored every six hours at each of 212 locations throughout the 16 plots with time domain reflectrometry (TDR) techniques using an automated and multiplexed measurement system. Field data is presented to show the effects of slope and slope length on the performance of each landfill cover design for the first 15 months of this field experiment

  20. Accreditation proposal for control systems in electrical engineering for 6th level in European Qualification Framework (EQF)

    DEFF Research Database (Denmark)

    Tsirigotis, Georgios; Friesel, Anna

    2013-01-01

    The progress of science and technology emphasizes the connection between different domains and disciplines. The technology development and changing demands of the labour market require upgrading and renewing of learning outcomes in higher education, especially in engineering fields. The Life Long...... Learning (LLL) procedure must be the platform offering the required qualifications for the demands of companies and engineering professionals all over the world in order to support their competitiveness. In this paper we describe an improved proposal for accreditation of one important subject...... in engineering, namely Control Systems. The described procedure could be applied in the frame of LLL and also in classical engineering education systems, such as university and college education, in order to harmonize the recognition of engineering degrees in Europe and outside the Europe. Furthermore we state...

  1. Impacts of Mid-level Biofuel Content in Gasoline on SIDI Engine-Out and Tailpipe Particulate Matter Emissions: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    He, X.; Ireland, J. C.; Zigler, B. T.; Ratcliff, M. A.; Knoll, K. E.; Alleman, T. L.; Tester, J. T.

    2011-02-01

    The influences of ethanol and iso-butanol blended with gasoline on engine-out and post Three-Way Catalyst (TWC) particle size distribution and number concentration were studied using a GM 2.0L turbocharged Spark Ignition Direct Injection (SIDI) engine. The engine was operated using the production ECU with a dynamometer controlling the engine speed and the accelerator pedal position controlling the engine load. A TSI Fast Mobility Particle Sizer (FMPS) spectrometer was used to measure the particle size distribution in the range from 5.6 to 560 nm with a sampling rate of 1 Hz. US federal certification gasoline (E0), two ethanol-blended fuels (E10 and E20), and 11.7% iso-butanol blended fuel (BU12) were tested. Measurements were conducted at ten selected steady-state engine operation conditions. Bi-modal particle size distributions were observed for all operating conditions with peak values at particle sizes of 10 nm and 70 nm. Idle and low speed / low load conditions emitted higher total particle numbers than other operating conditions. At idle, the engine-out Particulate Matter (PM) emissions were dominated by nucleation mode particles, and the production TWC reduced these nucleation mode particles by more than 50%, while leaving the accumulation mode particle distribution unchanged. At engine load higher than 6 bar NMEP, accumulation mode particles dominated the engine-out particle emissions and the TWC had little effect. Compared to the baseline gasoline (E0), E10 does not significantly change PM emissions, while E20 and BU12 both reduce PM emissions under the conditions studied. Iso-butanol was observed to impact PM emissions more than ethanol, with up to 50% reductions at some conditions. In this paper, the issues related to PM measurement using FMPS are also discussed. While some uncertainties are due to engine variation, the FMPS must be operated under careful maintenance procedures in order to achieve repeatable measurement results.

  2. Research of some operating parameters and the emissions level variation in a spark ignited engine through on-board investigation methods in different loading conditions

    Science.gov (United States)

    Iosif, Ferenti; Baldean, Doru Laurean

    2014-06-01

    The present paper shows research made on a spark ignited engine with port fuel injection in different operation conditions in order to improve the comprehension about the cold start sequence, acceleration when changing the gear ratios, quality of combustion process and also any measures to be taken for pollutant reduction in such cases. The engineering endeavor encompasses the pollutants investigation during the operation time of gasoline supplied engine with four inline cylinders in different conditions. The temperature and any other parameters were measured with specific sensors installed on the engine or in the exhaust pipes. All the data collected has been evaluated using electronic investigation systems and highly developed equipment. In this manner it has enabled the outline of the idea of how pollutants of engine vary in different operating conditions. Air quality in the everyday environment is very important for the human health, and thus the ambient air quality has a well-known importance in the European pollution standards and legislation. The high level of attention directed to the pollution problem in the European lifestyle is a driving force for all kinds of studies in the field of the reduction of engine emission.

  3. Evaluation of the Effectiveness of the Integration of a LITEE Case Study for a Freshman Level Mechanical Engineering Course at The University of Toledo

    Science.gov (United States)

    Franchetti, Matthew

    2011-01-01

    The purpose of this paper is to report the findings of the integration of a manufacturing case study to a freshman level mechanical engineering course at The University of Toledo. The approach to integrate this case study into the class was completed via weekly assignments analyzing the case, small group discussion, and weekly group discussion.…

  4. Phonological reduplication in sign language: rules rule

    Directory of Open Access Journals (Sweden)

    Iris eBerent

    2014-06-01

    Full Text Available Productivity—the hallmark of linguistic competence—is typically attributed to algebraic rules that support broad generalizations. Past research on spoken language has documented such generalizations in both adults and infants. But whether algebraic rules form part of the linguistic competence of signers remains unknown. To address this question, here we gauge the generalization afforded by American Sign Language (ASL. As a case study, we examine reduplication (X→XX—a rule that, inter alia, generates ASL nouns from verbs. If signers encode this rule, then they should freely extend it to novel syllables, including ones with features that are unattested in ASL. And since reduplicated disyllables are preferred in ASL, such rule should favor novel reduplicated signs. Novel reduplicated signs should thus be preferred to nonreduplicative controls (in rating, and consequently, such stimuli should also be harder to classify as nonsigns (in the lexical decision task. The results of four experiments support this prediction. These findings suggest that the phonological knowledge of signers includes powerful algebraic rules. The convergence between these conclusions and previous evidence for phonological rules in spoken language suggests that the architecture of the phonological mind is partly amodal.

  5. Technical support of standards for high-level radioactive waste management. Volume B. Engineering controls. Task b report Mar-Aug 77

    International Nuclear Information System (INIS)

    1979-01-01

    This report is the result of work performed under the second part (Task B) of a four-part contract to gather technical information to evaluate enviornmental acceptablity of various options for disposing high-level wastes. The other tasks are: A-Source Term Characterization; C-Assessment of Migration Pathways; D-Assessment of Accidental Pathways. The scope of work for Task B was divided into 2 major steps: analysis of technology for engineering control of high-level wastes, and projections of costs for various alternative disposal technologies. Primary emphasis has been placed in non-reprocessed spent fuel. Brief consideration has been given to lower-level transuranic contaminated wastes which arise primarily from plutonium fuel fabrication and reprocessing plants. The objective of this limited review is to provide some insight into the state of the art for applying engineering controls to such wastes, including, where necessary, direct burial with high-level wastes in a geologic disposal facility

  6. How does the activity level of the parents influence their children's activity? The contemporary life in a world ruled by electronic devices.

    Science.gov (United States)

    Brzęk, Anna; Strauss, Markus; Przybylek, Bianca; Dworrak, Tarja; Dworrak, Birgit; Leischik, Roman

    2018-01-01

    Apart from many positive changes associated with technical civilization, there are also - from the health point of view - some threats. The reduction in the level of physical activity is one of them. The aim of the study was to investigate whether there are any relationships between children's physical activity and behaviors, and to assess the impact of the adults' activity on their children's habits. The study involved a group of 340 children aged 7-12 years (mean age: 9.81 ±1.7) and their parents. In order to evaluate children's physical activity and the amount of time that they spend with electronic devices, an original questionnaire and the IPAQ questionnaire were used. Children usually use electronic devices between 2 and 7 days per week (mean: 4.74 ±0.86), regardless of sex ( p > 0.09) and spend between 5 and 1620 min per week (mean: 459.46 ±308.1) with their mobile phone, tablet, PCs and TVs. 67.92% of boys and 69.61% of girls lead an active lifestyle. The children's activity level depends on their parents' level of activity ( p Parents of semi-active children lead a lifestyle with a moderate level of physical activity. The level of physical activity in younger children depends on the children's relationship with their parents and their level of activity. Children spend a lot of free time with their electronic devices. It is necessary to develop and implement activities intended to raise awareness of children and their families about the effects of hypokinesis.

  7. Electrochemical reverse engineering: A systems-level tool to probe the redox-based molecular communication of biology.

    Science.gov (United States)

    Li, Jinyang; Liu, Yi; Kim, Eunkyoung; March, John C; Bentley, William E; Payne, Gregory F

    2017-04-01

    The intestine is the site of digestion and forms a critical interface between the host and the outside world. This interface is composed of host epithelium and a complex microbiota which is "connected" through an extensive web of chemical and biological interactions that determine the balance between health and disease for the host. This biology and the associated chemical dialogues occur within a context of a steep oxygen gradient that provides the driving force for a variety of reduction and oxidation (redox) reactions. While some redox couples (e.g., catecholics) can spontaneously exchange electrons, many others are kinetically "insulated" (e.g., biothiols) allowing the biology to set and control their redox states far from equilibrium. It is well known that within cells, such non-equilibrated redox couples are poised to transfer electrons to perform reactions essential to immune defense (e.g., transfer from NADH to O 2 for reactive oxygen species, ROS, generation) and protection from such oxidative stresses (e.g., glutathione-based reduction of ROS). More recently, it has been recognized that some of these redox-active species (e.g., H 2 O 2 ) cross membranes and diffuse into the extracellular environment including lumen to transmit redox information that is received by atomically-specific receptors (e.g., cysteine-based sulfur switches) that regulate biological functions. Thus, redox has emerged as an important modality in the chemical signaling that occurs in the intestine and there have been emerging efforts to develop the experimental tools needed to probe this modality. We suggest that electrochemistry provides a unique tool to experimentally probe redox interactions at a systems level. Importantly, electrochemistry offers the potential to enlist the extensive theories established in signal processing in an effort to "reverse engineer" the molecular communication occurring in this complex biological system. Here, we review our efforts to develop this

  8. A Better Budget Rule

    Science.gov (United States)

    Dothan, Michael; Thompson, Fred

    2009-01-01

    Debt limits, interest coverage ratios, one-off balanced budget requirements, pay-as-you-go rules, and tax and expenditure limits are among the most important fiscal rules for constraining intertemporal transfers. There is considerable evidence that the least costly and most effective of such rules are those that focus directly on the rate of…

  9. Mixed and low-level waste treatment project: Appendix C, Health and safety criteria for the mixed and low-level waste treatment facility at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Neupauer, R.M.; Thurmond, S.M.

    1992-09-01

    This report describes health and safety concerns associated with the Mixed and Low-level Waste Treatment Facility at the Idaho National Engineering Laboratory. Various hazards are described such as fire, electrical, explosions, reactivity, temperature, and radiation hazards, as well as the potential for accidental spills, exposure to toxic materials, and other general safety concerns

  10. Mixed and low-level waste treatment project: Appendix C, Health and safety criteria for the mixed and low-level waste treatment facility at the Idaho National Engineering Laboratory. Part 1, Waste streams and treatment technologies

    Energy Technology Data Exchange (ETDEWEB)

    Neupauer, R.M.; Thurmond, S.M.

    1992-09-01

    This report describes health and safety concerns associated with the Mixed and Low-level Waste Treatment Facility at the Idaho National Engineering Laboratory. Various hazards are described such as fire, electrical, explosions, reactivity, temperature, and radiation hazards, as well as the potential for accidental spills, exposure to toxic materials, and other general safety concerns.

  11. Mixed and low-level waste treatment project: Appendix C, Health and safety criteria for the mixed and low-level waste treatment facility at the Idaho National Engineering Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Neupauer, R.M.; Thurmond, S.M.

    1992-09-01

    This report describes health and safety concerns associated with the Mixed and Low-level Waste Treatment Facility at the Idaho National Engineering Laboratory. Various hazards are described such as fire, electrical, explosions, reactivity, temperature, and radiation hazards, as well as the potential for accidental spills, exposure to toxic materials, and other general safety concerns.

  12. New Safety rules

    CERN Multimedia

    Safety Commission

    2008-01-01

    The revision of CERN Safety rules is in progress and the following new Safety rules have been issued on 15-04-2008: Safety Procedure SP-R1 Establishing, Updating and Publishing CERN Safety rules: http://cern.ch/safety-rules/SP-R1.htm; Safety Regulation SR-S Smoking at CERN: http://cern.ch/safety-rules/SR-S.htm; Safety Regulation SR-M Mechanical Equipment: http://cern.ch/safety-rules/SR-M.htm; General Safety Instruction GSI-M1 Standard Lifting Equipment: http://cern.ch/safety-rules/GSI-M1.htm; General Safety Instruction GSI-M2 Standard Pressure Equipment: http://cern.ch/safety-rules/GSI-M2.htm; General Safety Instruction GSI-M3 Special Mechanical Equipment: http://cern.ch/safety-rules/GSI-M3.htm. These documents apply to all persons under the Director General’s authority. All Safety rules are available at the web page: http://www.cern.ch/safety-rules The Safety Commission

  13. Metal/nonmetal diesel particulate matter rule

    Energy Technology Data Exchange (ETDEWEB)

    Tomko, D.M. [United States Dept. of Labor, Mine Safety and Health Administration, Pittsburgh, PA (United States). Safety and Health Technology Center; Stackpole, R.P. [United States Dept. of Labor, Mine Safety and Health Administration, Triadelphia, WV (United States). Approval and Certification Center; Findlay, C.D. [United States Dept. of Labor, Mine Safety and Health Administration, Arlington, VA (United States). Metal/Nonmetal Safety and Health; Pomroy, W.H. [United States Dept. of Labor, Mine Safety and Health Administration, Duluth, MN (United States). Metal/Nonmetal North Central District

    2010-07-01

    The American Mine Safety and Health Administration (MSHA) issued a health standard in January 2001 designed to reduce exposure to diesel particulate matter (DPM) in underground metal and nonmetal mines. The rule established an interim concentration limit for DPM of 400 {mu}g/m{sup 3} of total carbon, to be followed in 2004 by a final limit of 160 {mu}g/m{sup 3} of total carbon. The 2001 rule was challenged in federal court by various mining trade associations and mining companies. The rule was subsequently amended. This paper highlighted the major provisions of the 2006 final rule and summarized MSHAs current compliance sampling procedures. The concentration limit was changed to a permissible exposure limit and the sampling surrogate was changed from total carbon to elemental carbon. The MSHA published a new rule in 2006 which based the final limit on a miner's personal exposure rather than a concentration limit. The final limit was phased in using 3 steps over 2 years. This paper also discussed engineering controls and a recent MSHA report on organic carbon, elemental carbon and total carbon emissions from a diesel engine fueled with various blends of standard diesel and biodiesel. In May 2008, about two-thirds of all underground metal/nonmetal mines achieved and maintained compliance with the rule. 20 refs.

  14. Action Rules Mining

    CERN Document Server

    Dardzinska, Agnieszka

    2013-01-01

    We are surrounded by data, numerical, categorical and otherwise, which must to be analyzed and processed to convert it into information that instructs, answers or aids understanding and decision making. Data analysts in many disciplines such as business, education or medicine, are frequently asked to analyze new data sets which are often composed of numerous tables possessing different properties. They try to find completely new correlations between attributes and show new possibilities for users.   Action rules mining discusses some of data mining and knowledge discovery principles and then describe representative concepts, methods and algorithms connected with action. The author introduces the formal definition of action rule, notion of a simple association action rule and a representative action rule, the cost of association action rule, and gives a strategy how to construct simple association action rules of a lowest cost. A new approach for generating action rules from datasets with numerical attributes...

  15. 18 CFR 385.104 - Rule of construction (Rule 104).

    Science.gov (United States)

    2010-04-01

    ... Definitions § 385.104 Rule of construction (Rule 104). To the extent that the text of a rule is inconsistent with its caption, the text of the rule controls. [Order 376, 49 FR 21705, May 23, 1984] ...

  16. How does the activity level of the parents influence their children’s activity? The contemporary life in a world ruled by electronic devices

    OpenAIRE

    Brzęk, Anna; Strauss, Markus; Przybylek, Bianca; Dworrak, Tarja; Dworrak, Birgit; Leischik, Roman

    2017-01-01

    Introduction Apart from many positive changes associated with technical civilization, there are also – from the health point of view – some threats. The reduction in the level of physical activity is one of them. The aim of the study was to investigate whether there are any relationships between children’s physical activity and behaviors, and to assess the impact of the adults’ activity on their children’s habits. Material and methods The study involved a group of 340 children aged 7–12 years...

  17. WellnessRules: A Web 3.0 Case Study in RuleML-Based Prolog-N3 Profile Interoperation

    Science.gov (United States)

    Boley, Harold; Osmun, Taylor Michael; Craig, Benjamin Larry

    An interoperation study, WellnessRules, is described, where rules about wellness opportunities are created by participants in rule languages such as Prolog and N3, and translated within a wellness community using RuleML/XML. The wellness rules are centered around participants, as profiles, encoding knowledge about their activities conditional on the season, the time-of-day, the weather, etc. This distributed knowledge base extends FOAF profiles with a vocabulary and rules about wellness group networking. The communication between participants is organized through Rule Responder, permitting wellness-profile translation and distributed querying across engines. WellnessRules interoperates between rules and queries in the relational (Datalog) paradigm of the pure-Prolog subset of POSL and in the frame (F-logic) paradigm of N3. An evaluation of Rule Responder instantiated for WellnessRules revealed acceptable Web response times.

  18. Potential Implications of Approaches to Climate Change on the Clean Water Rule Definition of "Waters of the United States".

    Science.gov (United States)

    Faust, Derek R; Moore, Matthew T; Emison, Gerald Andrews; Rush, Scott A

    2016-05-01

    The 1972 Clean Water Act was passed to protect chemical, physical, and biological integrity of United States' waters. The U.S. Environmental Protection Agency and U.S. Army Corps of Engineers codified a new "waters of the United States" rule on June 29, 2015, because several Supreme Court case decisions caused confusion with the existing rule. Climate change could affect this rule through connectivity between groundwater and surface waters; floodplain waters and the 100-year floodplain; changes in jurisdictional status; and sea level rise on coastal ecosystems. Four approaches are discussed for handling these implications: (1) "Wait and see"; (2) changes to the rule; (3) use guidance documents; (4) Congress statutorily defining "waters of the United States." The approach chosen should be legally defensible and achieved in a timely fashion to provide protection to "waters of the United States" in proactive consideration of scientifically documented effects of climate change on aquatic ecosystems.

  19. Is integrative use of techniques in psychotherapy the exception or the rule? Results of a national survey of doctoral-level practitioners.

    Science.gov (United States)

    Thoma, Nathan C; Cecero, John J

    2009-12-01

    This study sought to investigate the extent to which therapists endorse techniques outside of their self-identified orientation and which techniques are endorsed across orientations. A survey consisting of 127 techniques from 8 major theories of psychotherapy was administered via U.S. mail to a national random sample of doctoral-level psychotherapy practitioners. The 201 participants endorsed substantial numbers of techniques from outside their respective orientations. Many of these techniques were quite different from those of the core theories of the respective orientations. Further examining when and why experienced practitioners switch to techniques outside their primary orientation may help reveal where certain techniques fall short and where others excel, indicating a need for further research that taps the collective experience of practitioners. (PsycINFO Database Record (c) 2010 APA, all rights reserved).

  20. Estimation of a noise level using coarse-grained entropy of experimental time series of internal pressure in a combustion engine

    International Nuclear Information System (INIS)

    Litak, Grzegorz; Taccani, Rodolfo; Radu, Robert; Urbanowicz, Krzysztof; HoIyst, Janusz A.; Wendeker, MirosIaw; Giadrossi, Alessandro

    2005-01-01

    We report our results on non-periodic experimental time series of pressure in a single cylinder spark ignition engine. The experiments were performed for different levels of loading. We estimate the noise level in internal pressure calculating the coarse-grained entropy from variations of maximal pressures in successive cycles. The results show that the dynamics of the combustion is a non-linear multidimensional process mediated by noise. Our results show that so defined level of noise in internal pressure is not monotonous function of loading

  1. Evaluation of a Game to Teach Requirements Collection and Analysis in Software Engineering at Tertiary Education Level

    Science.gov (United States)

    Hainey, Thomas; Connolly, Thomas M.; Stansfield, Mark; Boyle, Elizabeth A.

    2011-01-01

    A highly important part of software engineering education is requirements collection and analysis which is one of the initial stages of the Database Application Lifecycle and arguably the most important stage of the Software Development Lifecycle. No other conceptual work is as difficult to rectify at a later stage or as damaging to the overall…

  2. The Problem-Solving Process in Physics as Observed When Engineering Students at University Level Work in Groups

    Science.gov (United States)

    Gustafsson, Peter; Jonsson, Gunnar; Enghag, Margareta

    2015-01-01

    The problem-solving process is investigated for five groups of students when solving context-rich problems in an introductory physics course included in an engineering programme. Through transcripts of their conversation, the paths in the problem-solving process have been traced and related to a general problem-solving model. All groups exhibit…

  3. Software Process Improvement through the Removal of Project-Level Knowledge Flow Obstacles: The Perceptions of Software Engineers

    Science.gov (United States)

    Mitchell, Susan Marie

    2012-01-01

    Uncontrollable costs, schedule overruns, and poor end product quality continue to plague the software engineering field. Innovations formulated with the expectation to minimize or eliminate cost, schedule, and quality problems have generally fallen into one of three categories: programming paradigms, software tools, and software process…

  4. Exploration of NSF-ATE Projects Approaches in the Integration of Technology and Engineering Education at the K-12 Levels

    Science.gov (United States)

    Strobel, Johannes; Mendoza Díaz, Noemi V.

    2012-01-01

    Access to post-secondary education, specifically in the technical, two-year institution area, is a topic of growing interest in the country. Funding agencies, such as NSF, via the Advanced Technological Education Program (ATE), are supporting initiatives and research aimed at increasing the number of technicians and engineers and improving…

  5. Discovering Sentinel Rules for Business Intelligence

    Science.gov (United States)

    Middelfart, Morten; Pedersen, Torben Bach

    This paper proposes the concept of sentinel rules for multi-dimensional data that warns users when measure data concerning the external environment changes. For instance, a surge in negative blogging about a company could trigger a sentinel rule warning that revenue will decrease within two months, so a new course of action can be taken. Hereby, we expand the window of opportunity for organizations and facilitate successful navigation even though the world behaves chaotically. Since sentinel rules are at the schema level as opposed to the data level, and operate on data changes as opposed to absolute data values, we are able to discover strong and useful sentinel rules that would otherwise be hidden when using sequential pattern mining or correlation techniques. We present a method for sentinel rule discovery and an implementation of this method that scales linearly on large data volumes.

  6. The biosphere rules.

    Science.gov (United States)

    Unruh, Gregory C

    2008-02-01

    Sustainability, defined by natural scientists as the capacity of healthy ecosystems to function indefinitely, has become a clarion call for business. Leading companies have taken high-profile steps toward achieving it: Wal-Mart, for example, with its efforts to reduce packaging waste, and Nike, which has removed toxic chemicals from its shoes. But, says Unruh, the director of Thunderbird's Lincoln Center for Ethics in Global Management, sustainability is more than an endless journey of incremental steps. It is a destination, for which the biosphere of planet Earth--refined through billions of years of trial and error--is a perfect model. Unruh distills some lessons from the biosphere into three rules: Use a parsimonious palette. Managers can rethink their sourcing strategies and dramatically simplify the number and types of materials their companies use in production, making recycling cost-effective. After the furniture manufacturer Herman Miller discovered that its leading desk chair had 200 components made from more than 800 chemical compounds, it designed an award-winning successor whose far more limited materials palette is 96% recyclable. Cycle up, virtuously. Manufacturers should design recovery value into their products at the outset. Shaw Industries, for example, recycles the nylon fiber from its worn-out carpet into brand-new carpet tile. Exploit the power of platforms. Platform design in industry tends to occur at the component level--but the materials in those components constitute a more fundamental platform. Patagonia, by recycling Capilene brand performance underwear, has achieved energy costs 76% below those for virgin sourcing. Biosphere rules can teach companies how to build ecologically friendly products that both reduce manufacturing costs and prove highly attractive to consumers. And managers need not wait for a green technological revolution to implement them.

  7. Free Energy and Internal Combustion Engine Cycles

    OpenAIRE

    Harris, William D.

    2012-01-01

    The performance of one type (Carnot) of Internal Combustion Engine (ICE) cycle is analyzed within the framework of thermodynamic free energies. ICE performance is different from that of an External Combustion Engine (ECE) which is dictated by Carnot's rule.

  8. Conformance Testing: Measurement Decision Rules

    Science.gov (United States)

    Mimbs, Scott M.

    2010-01-01

    The goal of a Quality Management System (QMS) as specified in ISO 9001 and AS9100 is to provide assurance to the customer that end products meet specifications. Measuring devices, often called measuring and test equipment (MTE), are used to provide the evidence of product conformity to specified requirements. Unfortunately, processes that employ MTE can become a weak link to the overall QMS if proper attention is not given to the measurement process design, capability, and implementation. Documented "decision rules" establish the requirements to ensure measurement processes provide the measurement data that supports the needs of the QMS. Measurement data are used to make the decisions that impact all areas of technology. Whether measurements support research, design, production, or maintenance, ensuring the data supports the decision is crucial. Measurement data quality can be critical to the resulting consequences of measurement-based decisions. Historically, most industries required simplistic, one-size-fits-all decision rules for measurements. One-size-fits-all rules in some cases are not rigorous enough to provide adequate measurement results, while in other cases are overly conservative and too costly to implement. Ideally, decision rules should be rigorous enough to match the criticality of the parameter being measured, while being flexible enough to be cost effective. The goal of a decision rule is to ensure that measurement processes provide data with a sufficient level of quality to support the decisions being made - no more, no less. This paper discusses the basic concepts of providing measurement-based evidence that end products meet specifications. Although relevant to all measurement-based conformance tests, the target audience is the MTE end-user, which is anyone using MTE other than calibration service providers. Topics include measurement fundamentals, the associated decision risks, verifying conformance to specifications, and basic measurement

  9. Technical rules in law

    Energy Technology Data Exchange (ETDEWEB)

    Debelius, J

    1978-08-01

    An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself.

  10. Technical rules in law

    International Nuclear Information System (INIS)

    Debelius, J.

    1978-01-01

    An important source of knowledge for technical experts is the state of the art reflected by catalogues of technical rules. Technical rules may also achieve importance in law due to a legal transformation standard. Here, rigid and flexible reference are controversial with regard to their admissibility from the point of view of constitutional law. In case of a divergence from the generally accepted technical rules, it is assumed - refutably - that the necessary care had not been taken. Technical rules are one out of several sources of information; they have no normative effect. This may result in a duty of anyone applying them to review the state of technology himself. (orig.) [de

  11. Strategy as simple rules.

    Science.gov (United States)

    Eisenhardt, K M; Sull, D N

    2001-01-01

    The success of Yahoo!, eBay, Enron, and other companies that have become adept at morphing to meet the demands of changing markets can't be explained using traditional thinking about competitive strategy. These companies have succeeded by pursuing constantly evolving strategies in market spaces that were considered unattractive according to traditional measures. In this article--the third in an HBR series by Kathleen Eisenhardt and Donald Sull on strategy in the new economy--the authors ask, what are the sources of competitive advantage in high-velocity markets? The secret, they say, is strategy as simple rules. The companies know that the greatest opportunities for competitive advantage lie in market confusion, but they recognize the need for a few crucial strategic processes and a few simple rules. In traditional strategy, advantage comes from exploiting resources or stable market positions. In strategy as simple rules, advantage comes from successfully seizing fleeting opportunities. Key strategic processes, such as product innovation, partnering, or spinout creation, place the company where the flow of opportunities is greatest. Simple rules then provide the guidelines within which managers can pursue such opportunities. Simple rules, which grow out of experience, fall into five broad categories: how- to rules, boundary conditions, priority rules, timing rules, and exit rules. Companies with simple-rules strategies must follow the rules religiously and avoid the temptation to change them too frequently. A consistent strategy helps managers sort through opportunities and gain short-term advantage by exploiting the attractive ones. In stable markets, managers rely on complicated strategies built on detailed predictions of the future. But when business is complicated, strategy should be simple.

  12. Rules, culture, and fitness.

    Science.gov (United States)

    Baum, W M

    1995-01-01

    Behavior analysis risks intellectual isolation unless it integrates its explanations with evolutionary theory. Rule-governed behavior is an example of a topic that requires an evolutionary perspective for a full understanding. A rule may be defined as a verbal discriminative stimulus produced by the behavior of a speaker under the stimulus control of a long-term contingency between the behavior and fitness. As a discriminative stimulus, the rule strengthens listener behavior that is reinforced in the short run by socially mediated contingencies, but which also enters into the long-term contingency that enhances the listener's fitness. The long-term contingency constitutes the global context for the speaker's giving the rule. When a rule is said to be "internalized," the listener's behavior has switched from short- to long-term control. The fitness-enhancing consequences of long-term contingencies are health, resources, relationships, or reproduction. This view ties rules both to evolutionary theory and to culture. Stating a rule is a cultural practice. The practice strengthens, with short-term reinforcement, behavior that usually enhances fitness in the long run. The practice evolves because of its effect on fitness. The standard definition of a rule as a verbal statement that points to a contingency fails to distinguish between a rule and a bargain ("If you'll do X, then I'll do Y"), which signifies only a single short-term contingency that provides mutual reinforcement for speaker and listener. In contrast, the giving and following of a rule ("Dress warmly; it's cold outside") can be understood only by reference also to a contingency providing long-term enhancement of the listener's fitness or the fitness of the listener's genes. Such a perspective may change the way both behavior analysts and evolutionary biologists think about rule-governed behavior.

  13. Binary effectivity rules

    DEFF Research Database (Denmark)

    Keiding, Hans; Peleg, Bezalel

    2006-01-01

    is binary if it is rationalized by an acyclic binary relation. The foregoing result motivates our definition of a binary effectivity rule as the effectivity rule of some binary SCR. A binary SCR is regular if it satisfies unanimity, monotonicity, and independence of infeasible alternatives. A binary...

  14. Delayed rule following.

    Science.gov (United States)

    Schmitt, D R

    2001-01-01

    Although the elements of a fully stated rule (discriminative stimulus [S(D)], some behavior, and a consequence) can occur nearly contemporaneously with the statement of the rule, there is often a delay between the rule statement and the S(D). The effects of this delay on rule following have not been studied in behavior analysis, but they have been investigated in rule-like settings in the areas of prospective memory (remembering to do something in the future) and goal pursuit. Discriminative events for some behavior can be event based (a specific setting stimulus) or time based. The latter are more demanding with respect to intention following and show age-related deficits. Studies suggest that the specificity with which the components of a rule (termed intention) are stated has a substantial effect on intention following, with more detailed specifications increasing following. Reminders of an intention, too, are most effective when they refer specifically to both the behavior and its occasion. Covert review and written notes are two effective strategies for remembering everyday intentions, but people who use notes appear not to be able to switch quickly to covert review. By focusing on aspects of the setting and rule structure, research on prospective memory and goal pursuit expands the agenda for a more complete explanation of rule effects.

  15. "Chaos Rules" Revisited

    Science.gov (United States)

    Murphy, David

    2011-01-01

    About 20 years ago, while lost in the midst of his PhD research, the author mused over proposed titles for his thesis. He was pretty pleased with himself when he came up with "Chaos Rules" (the implied double meaning was deliberate), or more completely, "Chaos Rules: An Exploration of the Work of Instructional Designers in Distance Education." He…

  16. How Good Is Your Rule of Thumb? Validating Male-to-Female Case Ratio as a Proxy for Men Who Have Sex With Men Involvement in N. gonorrhoeae Incidence at the County Level.

    Science.gov (United States)

    Stenger, Mark; Bauer, Heidi; Klingler, Ellen; Bell, Teal; Donnelly, Jennifer; Eaglin, Margaret; Jespersen, Megan; Madera, Robbie; Mattson, Melanie; Torrone, Elizabeth

    2018-03-01

    Lacking information on men who have sex with men (MSM) for most reported cases, sexually transmitted disease (STD) programs in the United States have used crude measures such as male-to-female case ratios (MFCR) as a rule of thumb to gauge MSM involvement at the local level, primarily with respect to syphilis cases in the past. Suitability of this measure for gonorrhea incidence has not previously been investigated. A random sample of gonorrhea cases reported from January 2010 through June 2013 were interviewed in selected counties participating in the STD Surveillance Network to obtain gender of sex partners and history of transactional sex. Weighted estimates of proportion of cases among MSM and proportion reporting transactional sex were developed; correlation between MFCR and proportion MSM was assessed. Male-to-female case ratio ranged from 0.66 to 8.7, and the proportion of cases occurring among MSM varied from 2.5% to 62.3%. The MFCR was strongly correlated with proportion of cases among MSM after controlling for transactional sex (Pearson partial r = 0.754, P < 0.0001). Male-to-female case ratio for gonorrhea at the county level is a reliable proxy measure indicating MSM involvement in gonorrhea case incidence and should be used by STD programs to tailor their programmatic mix to include MSM-specific interventions.

  17. Electronuclear sum rules

    International Nuclear Information System (INIS)

    Arenhoevel, H.; Drechsel, D.; Weber, H.J.

    1978-01-01

    Generalized sum rules are derived by integrating the electromagnetic structure functions along lines of constant ratio of momentum and energy transfer. For non-relativistic systems these sum rules are related to the conventional photonuclear sum rules by a scaling transformation. The generalized sum rules are connected with the absorptive part of the forward scattering amplitude of virtual photons. The analytic structure of the scattering amplitudes and the possible existence of dispersion relations have been investigated in schematic relativistic and non-relativistic models. While for the non-relativistic case analyticity does not hold, the relativistic scattering amplitude is analytical for time-like (but not for space-like) photons and relations similar to the Gell-Mann-Goldberger-Thirring sum rule exist. (Auth.)

  18. RIGHTS, RULES, AND DEMOCRACY

    Directory of Open Access Journals (Sweden)

    Richard S. Kay, University of Connecticut-School of Law, Estados Unidos

    2012-11-01

    Full Text Available Abstract: Democracy require protection of certain fundamental rights, but can we expect courts to follow rules? There seems little escape from the proposition that substantive constitutional review by an unelected judiciary is a presumptive abridgement of democratic decision-making. Once we have accepted the proposition that there exist human rights that ought to be protected, this should hardly surprise us. No one thinks courts are perfect translators of the rules invoked before them on every occasion. But it is equally clear that rules sometimes do decide cases. In modern legal systems the relative roles of courts and legislators with respect to the rules of the system is a commonplace. Legislatures make rules. Courts apply them in particular disputes. When we are talking about human rights, however, that assumption must be clarified in at least one way. The defense of the practice of constitutional review in this article assumes courts can and do enforce rules. This article also makes clear what is the meaning of “following rules”. Preference for judicial over legislative interpretation of rights, therefore, seems to hang on the question of whether or not judges are capable of subordinating their own judgment to that incorporated in the rules by their makers. This article maintains that, in general, entrenched constitutional rules (and not just constitutional courts can and do constrain public conduct and protect human rights. The article concludes that the value judgments will depend on our estimate of the benefits we derive from the process of representative self-government. Against those benefits we will have to measure the importance we place on being able to live our lives with the security created by a regime of human rights protected by the rule of law. Keywords: Democracy. Human Rights. Rules. Judicial Review.

  19. LIS Professionals as Knowledge Engineers.

    Science.gov (United States)

    Poulter, Alan; And Others

    1994-01-01

    Considers the role of library and information science professionals as knowledge engineers. Highlights include knowledge acquisition, including personal experience, interviews, protocol analysis, observation, multidimensional sorting, printed sources, and machine learning; knowledge representation, including production rules and semantic nets;…

  20. Engineering surveying

    CERN Document Server

    Schofield, W

    2001-01-01

    The aim of Engineering Surveying has always been to impart and develop a clear understanding of the basic topics of the subject. The author has fully revised the book to make it the most up-to-date and relevant textbook available on the subject.The book also contains the latest information on trigonometric levelling, total stations and one-person measuring systems. A new chapter on satellites ensures a firm grasp of this vitally important topic.The text covers engineering surveying modules for civil engineering students on degree courses and forms a reference for the engineering surveying module in land surveying courses. It will also prove to be a valuable reference for practitioners.* Simple clear introduction to surveying for engineers* Explains key techniques and methods* Details reading systems and satellite position fixing

  1. Increase in the Accuracy of Calculating Length of Horizontal Cable SCS in Civil Engineering

    Science.gov (United States)

    Semenov, A.

    2017-11-01

    A modification of the method for calculating the horizontal cable consumption of SCS established at civil engineering facilities is proposed. The proposed procedure preserves the prototype simplicity and provides a 5 percent accuracy increase. The values of the achieved accuracy are justified, their compliance with the practice of real projects is proved. The method is brought to the level of the engineering algorithm and formalized in the form of 12/70 rule.

  2. Radiant heat transfers in turbojet engines. Two applications, three levels of modeling; Transferts radiatifs dans les foyers de turboreacteurs. Deux applications, trois niveaux de modelisation

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, J L; Desaulty, M [SNECMA, Centre de Villaroche, 77 - Moissy-Cramayel (France); Taine, J [Ecole Centrale de Paris, Laboratoire EM2C. CNRS, 92 - Chatenay-Malabry (France)

    1997-12-31

    Several applications linked with the dimensioning of turbojet engines require the use of modeling of radiant heat transfers. Two different applications are presented in this study: the modeling of heat transfers in the main combustion chamber, and modeling of the infrared signature of the post-combustion chamber of a military engine. In the first application, two types of radiant heat transfer modeling are presented: a global modeling based on empirical considerations and used in rapid pre-dimensioning methods, and a modeling based on a grey gases concept and combined to a ray shooting type technique allowing the determination of local radiant heat flux values. In the second application, a specific modeling of the radiant heat flux is used in the framework of a ray shooting method. Each model represents a different level of successive approximations of the radiant heat transfer adapted to flow specificities and to the performance requested. (J.S.) 16 refs.

  3. Radiant heat transfers in turbojet engines. Two applications, three levels of modeling; Transferts radiatifs dans les foyers de turboreacteurs. Deux applications, trois niveaux de modelisation

    Energy Technology Data Exchange (ETDEWEB)

    Schultz, J.L.; Desaulty, M. [SNECMA, Centre de Villaroche, 77 - Moissy-Cramayel (France); Taine, J. [Ecole Centrale de Paris, Laboratoire EM2C. CNRS, 92 - Chatenay-Malabry (France)

    1996-12-31

    Several applications linked with the dimensioning of turbojet engines require the use of modeling of radiant heat transfers. Two different applications are presented in this study: the modeling of heat transfers in the main combustion chamber, and modeling of the infrared signature of the post-combustion chamber of a military engine. In the first application, two types of radiant heat transfer modeling are presented: a global modeling based on empirical considerations and used in rapid pre-dimensioning methods, and a modeling based on a grey gases concept and combined to a ray shooting type technique allowing the determination of local radiant heat flux values. In the second application, a specific modeling of the radiant heat flux is used in the framework of a ray shooting method. Each model represents a different level of successive approximations of the radiant heat transfer adapted to flow specificities and to the performance requested. (J.S.) 16 refs.

  4. Modeling of release of radionuclides from an engineered disposal facility for shallow-land disposal of low-level radioactive wastes

    International Nuclear Information System (INIS)

    Matsuzuru, H.; Suzuki, A.

    1989-01-01

    The computer code, ENBAR-1, for the simulation of radionuclide releases from an engineered disposal facility has been developed to evaluate the source term for subsequent migration of radionuclides in and through a natural barrier. The system considered here is that a waste package (waste form and container) is placed, together with backfill materials, into a concrete pit as a disposal unit for shallow-land disposal of low-level radioactive wastes. The code developed includes the following modules: water penetration into a concrete pit, corrosion of a drum as a container, leaching of radionuclides from a waste form, migration of radionuclides in backfill materials, release of radionuclides from the pit. The code has the advantage of its simplicity of operation and presentation while still allowing comprehensive evaluation of each element of an engineered disposal facility to be treated. The performance and source term of the facility might be readily estimated with a few key parameters to define the problem

  5. Totally optimal decision rules

    KAUST Repository

    Amin, Talha

    2017-11-22

    Optimality of decision rules (patterns) can be measured in many ways. One of these is referred to as length. Length signifies the number of terms in a decision rule and is optimally minimized. Another, coverage represents the width of a rule’s applicability and generality. As such, it is desirable to maximize coverage. A totally optimal decision rule is a decision rule that has the minimum possible length and the maximum possible coverage. This paper presents a method for determining the presence of totally optimal decision rules for “complete” decision tables (representations of total functions in which different variables can have domains of differing values). Depending on the cardinalities of the domains, we can either guarantee for each tuple of values of the function that totally optimal rules exist for each row of the table (as in the case of total Boolean functions where the cardinalities are equal to 2) or, for each row, we can find a tuple of values of the function for which totally optimal rules do not exist for this row.

  6. Totally optimal decision rules

    KAUST Repository

    Amin, Talha M.; Moshkov, Mikhail

    2017-01-01

    Optimality of decision rules (patterns) can be measured in many ways. One of these is referred to as length. Length signifies the number of terms in a decision rule and is optimally minimized. Another, coverage represents the width of a rule’s applicability and generality. As such, it is desirable to maximize coverage. A totally optimal decision rule is a decision rule that has the minimum possible length and the maximum possible coverage. This paper presents a method for determining the presence of totally optimal decision rules for “complete” decision tables (representations of total functions in which different variables can have domains of differing values). Depending on the cardinalities of the domains, we can either guarantee for each tuple of values of the function that totally optimal rules exist for each row of the table (as in the case of total Boolean functions where the cardinalities are equal to 2) or, for each row, we can find a tuple of values of the function for which totally optimal rules do not exist for this row.

  7. Fluids engineering

    International Nuclear Information System (INIS)

    Anon.

    1991-01-01

    Fluids engineering has played an important role in many applications, from ancient flood control to the design of high-speed compact turbomachinery. New applications of fluids engineering, such as in high-technology materials processing, biotechnology, and advanced combustion systems, have kept up unwaining interest in the subject. More accurate and sophisticated computational and measurement techniques are also constantly being developed and refined. On a more fundamental level, nonlinear dynamics and chaotic behavior of fluid flow are no longer an intellectual curiosity and fluid engineers are increasingly interested in finding practical applications for these emerging sciences. Applications of fluid technology to new areas, as well as the need to improve the design and to enhance the flexibility and reliability of flow-related machines and devices will continue to spur interest in fluids engineering. The objectives of the present seminar were: to exchange current information on arts, science, and technology of fluids engineering; to promote scientific cooperation between the fluids engineering communities of both nations, and to provide an opportunity for the participants and their colleagues to explore possible joint research programs in topics of high priority and mutual interest to both countries. The Seminar provided an excellent forum for reviewing the current state and future needs of fluids engineering for the two nations. With the Seminar ear-marking the first formal scientific exchange between Korea and the United States in the area of fluids engineering, the scope was deliberately left broad and general

  8. Decision support system for triage management: A hybrid approach using rule-based reasoning and fuzzy logic.

    Science.gov (United States)

    Dehghani Soufi, Mahsa; Samad-Soltani, Taha; Shams Vahdati, Samad; Rezaei-Hachesu, Peyman

    2018-06-01

    Fast and accurate patient triage for the response process is a critical first step in emergency situations. This process is often performed using a paper-based mode, which intensifies workload and difficulty, wastes time, and is at risk of human errors. This study aims to design and evaluate a decision support system (DSS) to determine the triage level. A combination of the Rule-Based Reasoning (RBR) and Fuzzy Logic Classifier (FLC) approaches were used to predict the triage level of patients according to the triage specialist's opinions and Emergency Severity Index (ESI) guidelines. RBR was applied for modeling the first to fourth decision points of the ESI algorithm. The data relating to vital signs were used as input variables and modeled using fuzzy logic. Narrative knowledge was converted to If-Then rules using XML. The extracted rules were then used to create the rule-based engine and predict the triage levels. Fourteen RBR and 27 fuzzy rules were extracted and used in the rule-based engine. The performance of the system was evaluated using three methods with real triage data. The accuracy of the clinical decision support systems (CDSSs; in the test data) was 99.44%. The evaluation of the error rate revealed that, when using the traditional method, 13.4% of the patients were miss-triaged, which is statically significant. The completeness of the documentation also improved from 76.72% to 98.5%. Designed system was effective in determining the triage level of patients and it proved helpful for nurses as they made decisions, generated nursing diagnoses based on triage guidelines. The hybrid approach can reduce triage misdiagnosis in a highly accurate manner and improve the triage outcomes. Copyright © 2018 Elsevier B.V. All rights reserved.

  9. Following the Rules.

    Science.gov (United States)

    Katz, Anne

    2016-05-01

    I am getting better at following the rules as I grow older, although I still bristle at many of them. I was a typical rebellious teenager; no one understood me, David Bowie was my idol, and, one day, my generation was going to change the world. Now I really want people to understand me: David Bowie remains one of my favorite singers and, yes, my generation has changed the world, and not necessarily for the better. Growing up means that you have to make the rules, not just follow those set by others, and, at times, having rules makes a lot of sense.
.

  10. Do Fiscal Rules Matter?

    DEFF Research Database (Denmark)

    Grembi, Veronica; Nannicini, Tommaso; Troiano, Ugo

    2016-01-01

    , the central government imposed fiscal rules on municipal governments, and in 2001 relaxed them below 5,000 inhabitants. We exploit the before/after and discontinuous policy variation, and show that relaxing fiscal rules increases deficits and lowers taxes. The effect is larger if the mayor can be reelected......Fiscal rules are laws aimed at reducing the incentive to accumulate debt, and many countries adopt them to discipline local governments. Yet, their effectiveness is disputed because of commitment and enforcement problems. We study their impact applying a quasi-experimental design in Italy. In 1999...

  11. Incorporation of high-level wastes in SYNROC: results from recent process-engineering studies at Lawrence Livermore National Laboratory

    International Nuclear Information System (INIS)

    Campbell, J.H.; Hoenig, C.L.; Ackerman, F.J.; Peters, P.E.; Grens, J.Z.

    1982-01-01

    In this paper, highlights from recent engineering research and development, in particular, results from fluidized bed calcination studies of SYNROC slurry are summarized. A schematic diagram of the envisioned SYNROC process (at this stage of development) is also presented. It shows the use of a fluidized bed calciner to prepare SYNROC powder that is then fed to a storage hopper. Bellows-type canisters are filled, evacuated, sealed and preheated. The preheated canisters are loaded into a hot isotactic pressing unit where they are densified, then removed and cooled and finally loaded into a waste storage container. After sealing, this container is decontaminated and transferred to the interim storage facility and then, ultimately, to an underground repository

  12. Privacy-Preserving Detection of Inter-Domain SDN Rules Overlaps

    KAUST Repository

    Dethise, Arnaud

    2017-08-24

    SDN approaches to inter-domain routing promise better traffic engineering, enhanced security, and higher automation. Yet, naïve deployment of SDN on the Internet is dangerous as the control-plane expressiveness of BGP is significantly more limited than the data-plane expressiveness of SDN, which allows fine-grained rules to deflect traffic from BGP\\'s default routes. This mismatch may lead to incorrect forwarding behaviors such as forwarding loops and blackholes, ultimately hindering SDN deployment at the inter-domain level. In this work, we make a first step towards verifying the correctness of inter-domain forwarding state with a focus on loop freedom while keeping private the SDN rules, as they comprise confidential routing information. To this end, we design a simple yet powerful primitive that allows two networks to verify whether their SDN rules overlap, i.e., the set of packets matched by these rules is non-empty, without leaking any information about the SDN rules. We propose an efficient implementation of this primitive by using recent advancements in Secure Multi-Party Computation and we then leverage it as the main building block for designing a system that detects Internet-wide forwarding loops among any set of SDN-enabled Internet eXchange Points.

  13. Pollution provoquée par le moteur Diesel. Niveaux d'émission. Comparaison avec le moteur à allumage commandé Pollution Caused by Diesel Engines. Emission Levels. Comparison with Spark-Ignition Engines

    Directory of Open Access Journals (Sweden)

    Degobert P.

    2006-11-01

    Full Text Available A partir de l'analyse des différences de modes de combustion allumage commandé et Diesel , cet article compare et explique la nature et les niveaux des différents polluants émis en fonction de leurs mécanismes de formation. Les facteurs d'action au niveau moteur sont examinés, ainsi que l'influence du carburant utilisé. Based on an analysis of the difference between spark-ignition and diesel combustion modes, this article compares and explains the nature and levels of different pollutants emitted as a function of their formation mechanisms. The action factors at the engine> level are examined together with the influence of the fuel used.

  14. Assessment of the Orion-SLS Interface Management Process in Achieving the EIA 731.1 Systems Engineering Capability Model Generic Practices Level 3 Criteria

    Science.gov (United States)

    Jellicorse, John J.; Rahman, Shamin A.

    2016-01-01

    NASA is currently developing the next generation crewed spacecraft and launch vehicle for exploration beyond earth orbit including returning to the Moon and making the transit to Mars. Managing the design integration of major hardware elements of a space transportation system is critical for overcoming both the technical and programmatic challenges in taking a complex system from concept to space operations. An established method of accomplishing this is formal interface management. In this paper we set forth an argument that the interface management process implemented by NASA between the Orion Multi-Purpose Crew Vehicle (MPCV) and the Space Launch System (SLS) achieves the Level 3 tier of the EIA 731.1 System Engineering Capability Model (SECM) for Generic Practices. We describe the relevant NASA systems and associated organizations, and define the EIA SECM Level 3 Generic Practices. We then provide evidence for our compliance with those practices. This evidence includes discussions of: NASA Systems Engineering Interface (SE) Management standard process and best practices; the tailoring of that process for implementation on the Orion to SLS interface; changes made over time to improve the tailored process, and; the opportunities to take the resulting lessons learned and propose improvements to our institutional processes and best practices. We compare this evidence against the practices to form the rationale for the declared SECM maturity level.

  15. Control Performance of General Electric Fuel and Torque Regulator Operating on T31-3 Turbine-Propeller Engine in Sea-Level Test Stand

    Science.gov (United States)

    Oppenheimer, Frank L.; Lazar, James

    1951-01-01

    A .General Electric fuel and torque regulator was tested in conjunction with a T31-3 turbine-propeller engine in the sea-level static test stand at the NACA Lewis laboratory. The engine and control were operated over the entire speed range: 11,000 rpm, nominal flight idle, to 13,000 rpm, full power. Steady-state and transient data were recorded and are presented with a description of the four control loops being used in the system. Results of this investigation indicated that single-lever control operation was satisfactory under conditions of test. Transient data presented showed that turbine-outlet temperature did overshoot maximum operating value on acceleration but that the time duration of overshoot did not exceed approximately 1 second. This temperature limiting resulted from a control on fuel flow as a function of engine speed. Speed and torque first reached their desired values 0.4 second from the time of change in power-setting lever position. Maximum speed overshoot was 3 percent.

  16. Optical Generation of Fuzzy-Based Rules

    Science.gov (United States)

    Gur, Eran; Mendlovic, David; Zalevsky, Zeev

    2002-08-01

    In the last third of the 20th century, fuzzy logic has risen from a mathematical concept to an applicable approach in soft computing. Today, fuzzy logic is used in control systems for various applications, such as washing machines, train-brake systems, automobile automatic gear, and so forth. The approach of optical implementation of fuzzy inferencing was given by the authors in previous papers, giving an extra emphasis to applications with two dominant inputs. In this paper the authors introduce a real-time optical rule generator for the dual-input fuzzy-inference engine. The paper briefly goes over the dual-input optical implementation of fuzzy-logic inferencing. Then, the concept of constructing a set of rules from given data is discussed. Next, the authors show ways to implement this procedure optically. The discussion is accompanied by an example that illustrates the transformation from raw data into fuzzy set rules.

  17. Rule-based decision making model

    International Nuclear Information System (INIS)

    Sirola, Miki

    1998-01-01

    A rule-based decision making model is designed in G2 environment. A theoretical and methodological frame for the model is composed and motivated. The rule-based decision making model is based on object-oriented modelling, knowledge engineering and decision theory. The idea of safety objective tree is utilized. Advanced rule-based methodologies are applied. A general decision making model 'decision element' is constructed. The strategy planning of the decision element is based on e.g. value theory and utility theory. A hypothetical process model is built to give input data for the decision element. The basic principle of the object model in decision making is division in tasks. Probability models are used in characterizing component availabilities. Bayes' theorem is used to recalculate the probability figures when new information is got. The model includes simple learning features to save the solution path. A decision analytic interpretation is given to the decision making process. (author)

  18. Staff rules and regulations

    CERN Multimedia

    HR Department

    2007-01-01

    The 11th edition of the Staff Rules and Regulations, dated 1 January 2007, adopted by the Council and the Finance Committee in December 2006, is currently being distributed to departmental secretariats. The Staff Rules and Regulations, together with a summary of the main modifications made, will be available, as from next week, on the Human Resources Department's intranet site: http://cern.ch/hr-web/internal/admin_services/rules/default.asp The main changes made to the Staff Rules and Regulations stem from the five-yearly review of employment conditions of members of the personnel. The changes notably relate to: the categories of members of the personnel (e.g. removal of the local staff category); the careers structure and the merit recognition system; the non-residence, installation and re-installation allowances; the definition of family, family allowances and family-related leave; recognition of partnerships; education fees. The administrative circulars, some of which are being revised following the ...

  19. Data breaches. Final rule.

    Science.gov (United States)

    2008-04-11

    This document adopts, without change, the interim final rule that was published in the Federal Register on June 22, 2007, addressing data breaches of sensitive personal information that is processed or maintained by the Department of Veterans Affairs (VA). This final rule implements certain provisions of the Veterans Benefits, Health Care, and Information Technology Act of 2006. The regulations prescribe the mechanisms for taking action in response to a data breach of sensitive personal information.

  20. A rule-based software test data generator

    Science.gov (United States)

    Deason, William H.; Brown, David B.; Chang, Kai-Hsiung; Cross, James H., II

    1991-01-01

    Rule-based software test data generation is proposed as an alternative to either path/predicate analysis or random data generation. A prototype rule-based test data generator for Ada programs is constructed and compared to a random test data generator. Four Ada procedures are used in the comparison. Approximately 2000 rule-based test cases and 100,000 randomly generated test cases are automatically generated and executed. The success of the two methods is compared using standard coverage metrics. Simple statistical tests showing that even the primitive rule-based test data generation prototype is significantly better than random data generation are performed. This result demonstrates that rule-based test data generation is feasible and shows great promise in assisting test engineers, especially when the rule base is developed further.

  1. Mechanisms of rule acquisition and rule following in inductive reasoning.

    Science.gov (United States)

    Crescentini, Cristiano; Seyed-Allaei, Shima; De Pisapia, Nicola; Jovicich, Jorge; Amati, Daniele; Shallice, Tim

    2011-05-25

    Despite the recent interest in the neuroanatomy of inductive reasoning processes, the regional specificity within prefrontal cortex (PFC) for the different mechanisms involved in induction tasks remains to be determined. In this study, we used fMRI to investigate the contribution of PFC regions to rule acquisition (rule search and rule discovery) and rule following. Twenty-six healthy young adult participants were presented with a series of images of cards, each consisting of a set of circles numbered in sequence with one colored blue. Participants had to predict the position of the blue circle on the next card. The rules that had to be acquired pertained to the relationship among succeeding stimuli. Responses given by subjects were categorized in a series of phases either tapping rule acquisition (responses given up to and including rule discovery) or rule following (correct responses after rule acquisition). Mid-dorsolateral PFC (mid-DLPFC) was active during rule search and remained active until successful rule acquisition. By contrast, rule following was associated with activation in temporal, motor, and medial/anterior prefrontal cortex. Moreover, frontopolar cortex (FPC) was active throughout the rule acquisition and rule following phases before a rule became familiar. We attributed activation in mid-DLPFC to hypothesis generation and in FPC to integration of multiple separate inferences. The present study provides evidence that brain activation during inductive reasoning involves a complex network of frontal processes and that different subregions respond during rule acquisition and rule following phases.

  2. Food Web Assembly Rules for Generalized Lotka-Volterra Equations

    DEFF Research Database (Denmark)

    Härter, Jan Olaf Mirko; Mitarai, Namiko; Sneppen, Kim

    2016-01-01

    the lack of niches, corresponding to unpaired species. For the species richness at each trophic level, we derive the food web assembly rules, which specify sustainable combinations. In neighboring levels, these rules allow the higher level to avert competitive exclusion at the lower, thereby incorporating...

  3. Study on mechanical stability of engineered barrier system for deep geological isolation of high-level radioactive waste

    International Nuclear Information System (INIS)

    Saotome, A.; Hara, K.; Fujita, T.; Sasaki, N.

    1991-01-01

    The evaluation of mechanical and hydraulic behavior of buffer material of engineered barrier system under water uptake was carried out by applying swelling-elasto-plastic model to the buffer material, of which swelling pressure was described by swelling coefficient. The result is that displacement of overpack and deformation of buffer material are negligibly small. The analysis on overpack sinking behavior within buffer material was carried out as the creep deformation of the buffer material. The analysis shows that creep sinking of overpack within buffer material is negligibly small if the density of buffer material is taken to some extent. The effects of dilatation of corrosion products by hydrogen-generating corrosion of carbon steel overpack was studied, because the dilatation is not negligible in a long-term period of time. As the results of elasto-plastic analysis, stress generated by the dilatation is absorbed within buffer material and dose not affect the host rock if the buffer material is packed to some extent in thickness. It is important to assess the migration of hydrogen within the buffer material. Based on the results of thermal calculations in the near-field maximum temperature acceptable to the buffer material can be controlled by the spacing of the waste package. The temperature in the near-field in case of avoiding the illitization of the buffer material is not so high as to affect the waste glass and the host rock. (author)

  4. Selection of a computer code for Hanford low-level waste engineered-system performance assessment. Revision 1

    International Nuclear Information System (INIS)

    McGrail, B.P.; Bacon, D.H.

    1998-02-01

    Planned performance assessments for the proposed disposal of low-activity waste (LAW) glass produced from remediation of wastes stored in underground tanks at Hanford, Washington will require calculations of radionuclide release rates from the subsurface disposal facility. These calculations will be done with the aid of computer codes. The available computer codes with suitable capabilities at the time Revision 0 of this document was prepared were ranked in terms of the feature sets implemented in the code that match a set of physical, chemical, numerical, and functional capabilities needed to assess release rates from the engineered system. The needed capabilities were identified from an analysis of the important physical and chemical processes expected to affect LAW glass corrosion and the mobility of radionuclides. This analysis was repeated in this report but updated to include additional processes that have been found to be important since Revision 0 was issued and to include additional codes that have been released. The highest ranked computer code was found to be the STORM code developed at PNNL for the US Department of Energy for evaluation of arid land disposal sites

  5. Enhanced levels of S-linalool by metabolic engineering of the terpenoid pathway in spike lavender leaves.

    Science.gov (United States)

    Mendoza-Poudereux, Isabel; Muñoz-Bertomeu, Jesús; Navarro, Alicia; Arrillaga, Isabel; Segura, Juan

    2014-05-01

    Transgenic Lavandula latifolia plants overexpressing the linalool synthase (LIS) gene from Clarkia breweri, encoding the LIS enzyme that catalyzes the synthesis of linalool were generated. Most of these plants increased significantly their linalool content as compared to controls, especially in the youngest leaves, where a linalool increase up to a 1000% was observed. The phenotype of increased linalool content observed in young leaves was maintained in those T1 progenies that inherit the LIS transgene, although this phenotype was less evident in the flower essential oil. Cross-pollination of transgenic spike lavender plants allowed the generation of double transgenic plants containing the DXS (1-deoxy-d-xylulose-5-P synthase), coding for the first enzyme of the methyl-d-erythritol-4-phosphate pathway, and LIS genes. Both essential oil yield and linalool content in double DXS-LIS transgenic plants were lower than that of their parentals, which could be due to co-suppression effects linked to the structures of the constructs used. Copyright © 2014 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

  6. Modular Engineering Concept at Novo Nordisk Engineering

    DEFF Research Database (Denmark)

    Moelgaard, Gert; Miller, Thomas Dedenroth

    1997-01-01

    This report describes the concept of a new engineering method at Novo Nordisk Engineering: Modular Engineering (ME). Three tools are designed to support project phases with different levels of detailing and abstraction. ME supports a standard, cross-functional breakdown of projects that facilitates...

  7. On the Application of Science Systems Engineering and Uncertainty Quantification for Ice Sheet Science and Sea Level Projections

    Science.gov (United States)

    Schlegel, Nicole-Jeanne; Boening, Carmen; Larour, Eric; Limonadi, Daniel; Schodlok, Michael; Seroussi, Helene; Watkins, Michael

    2017-04-01

    Research and development activities at the Jet Propulsion Laboratory (JPL) currently support the creation of a framework to formally evaluate the observational needs within earth system science. One of the pilot projects of this effort aims to quantify uncertainties in global mean sea level rise projections, due to contributions from the continental ice sheets. Here, we take advantage of established uncertainty quantification tools embedded within the JPL-University of California at Irvine Ice Sheet System Model (ISSM). We conduct sensitivity and Monte-Carlo style sampling experiments on forward simulations of the Greenland and Antarctic ice sheets. By varying internal parameters and boundary conditions of the system over both extreme and credible worst-case ranges, we assess the impact of the different parameter ranges on century-scale sea level rise projections. The results inform efforts to a) isolate the processes and inputs that are most responsible for determining ice sheet contribution to sea level; b) redefine uncertainty brackets for century-scale projections; and c) provide a prioritized list of measurements, along with quantitative information on spatial and temporal resolution, required for reducing uncertainty in future sea level rise projections. Results indicate that ice sheet mass loss is dependent on the spatial resolution of key boundary conditions - such as bedrock topography and melt rates at the ice-ocean interface. This work is performed at and supported by the California Institute of Technology's Jet Propulsion Laboratory. Supercomputing time is also supported through a contract with the National Aeronautics and Space Administration's Cryosphere program.

  8. Creating a Culture of Communication: A Graduate-Level STEM Communication Fellows Program at a Science and Engineering University

    Science.gov (United States)

    Simpson, Steve; Clemens, Rebecca; Killingsworth, Drea Rae; Ford, Julie Dyke

    2015-01-01

    A flurry of recent research in writing studies has addressed the need for more systematic approaches to graduate-level writing support, though more research is needed into more organic models that account for graduate students' specific needs and that build infrastructure for writing support within university departments. This article reports on a…

  9. Final project memorandum: sea-level rise modeling handbook: resource guide for resource managers, engineers, and scientists

    Science.gov (United States)

    Doyle, Thomas W.

    2015-01-01

    Coastal wetlands of the Southeastern United States are undergoing retreat and migration from increasing tidal inundation and saltwater intrusion attributed to climate variability and sea-level rise. Much of the literature describing potential sea-level rise projections and modeling predictions are found in peer-reviewed academic journals or government technical reports largely suited to reading by other Ph.D. scientists who are more familiar or engaged in the climate change debate. Various sea-level rise and coastal wetland models have been developed and applied of different designs and scales of spatial and temporal complexity for predicting habitat and environmental change that have not heretofore been synthesized to aid natural resource managers of their utility and limitations. Training sessions were conducted with Federal land managers with U.S. Fish and Wildlife Service, National Park Service, and NOAA National Estuarine Research Reserves as well as state partners and nongovernmental organizations across the northern Gulf Coast from Florida to Texas to educate and to evaluate user needs and understanding of concepts, data, and modeling tools for projecting sea-level rise and its impact on coastal habitats and wildlife. As a result, this handbook was constructed from these training and feedback sessions with coastal managers and biologists of published decision-support tools and simulation models for sea-level rise and climate change assessments. A simplified tabular context was developed listing the various kinds of decision-support tools and ecological models along with criteria to distinguish the source, scale, and quality of information input and geographic data sets, physical and biological constraints and relationships, datum characteristics of water and land elevation components, utility options for setting sea-level rise and climate change scenarios, and ease or difficulty of storing, displaying, or interpreting model output. The handbook is designed

  10. Teaching Professional Engineering Skills

    DEFF Research Database (Denmark)

    Andersson, Niclas; Andersson, Pernille Hammar

    2010-01-01

    evaluations, a questionnaire, and discussions with students confirm a genuinely positive attitude towards the role play simulation. The students engage in the role play and express an increased understanding of the requirements and the implicit rules of real-life engineering. The interaction between students...

  11. Engineering Faculty Indicate High Levels of Awareness and Use of the Library but Tend to Consult Google and Google Scholar First for Research Resources

    Directory of Open Access Journals (Sweden)

    Elaine Sullo

    2016-09-01

    Full Text Available A Review of: Zhang, L. (2015. Use of library services by engineering faculty at Mississippi State University, a large land grant institution. Science & Technology Libraries, 34(3, 272-286. http://dx.doi.org/10.1080/0194262X.2015.1090941 Objective – To investigate the engineering faculty’s information-seeking behaviour, experiences, awareness, and use of the university library. Design – Web-based survey questionnaire. Setting – The main campus of a state university in the United States of America. Subjects – 119 faculty members within 8 engineering departments. Methods – An email invitation to participate in a 16-item electronic survey questionnaire, with questions related to library use, was sent in the spring of 2015 to 119 engineering faculty members. Faculty were given 24 days to complete the survey, and a reminder email was sent 10 days after the original survey invitation. Main Results – Thirty-eight faculty members responded to the survey, representing a response rate of 32%. Overall, faculty had a high level of use and awareness of both online and physical library resources and services, although their awareness of certain scholarly communication services, such as data archiving and copyright advisory, was significantly lower. Faculty tend to turn to Google and Google Scholar when searching for information rather than turning to library databases. Faculty do not use social media to keep up with library news and updates. The library website, as well as liaison librarians, were cited as the primary sources for this type of information. Conclusions – The researcher concludes that librarians need to do a better job of marketing library resources, such as discipline-specific databases, as well as other library search tools. Because faculty use web search engines as a significant source of information, the author proposes further research on this behaviour, and suggests more action to educate faculty on different search tools

  12. Life fraction rules

    International Nuclear Information System (INIS)

    Maile, K.

    1989-01-01

    Evaluations for lifetime estimation of high temperature loaded HTR-components under creep fatigue load had been performed. The evaluations were carried out on the basis of experimental data of strain controlled fatigue tests with respectively without hold times performed on material NiCr 22 Co 12 Mo (Inconel 617). Life prediction was made by means of the linear damage accumulation rule. Due to the high temperatures no realistic estimates of creep damage can be obtained with this rule. Therefore the rule was modified. The modifications consist in a different analysis of the relaxation curve including different calculation of the creep damage estimate resp. in an extended rule, taking into consideration the interaction between creep and fatigue. In order to reach a better result transparency and to reduce data set dependent result scattering a round robin with a given data set was carried out. The round robin yielded that for a given test temperature of T = 950deg C realistic estimate of damage can be obtained with each modification. Furthermore a reduction of resulting scatterbands in the interaction diagram can be observed, i.e. the practicability of the rule has been increased. (orig.)

  13. The role of traffic rules.

    NARCIS (Netherlands)

    Noordzij, P.C.

    1988-01-01

    Experienced road users seem to have their own set of traffic rules (including rules about when to violate the official rules). The number of violations is enormous, causing great concern for the authorities. The situation could be improved by separating a set of rules with the aim of deterring road

  14. Communicating rules in recreation areas

    Science.gov (United States)

    Terence L. Ross; George H. Moeller

    1974-01-01

    Five hundred fifty-eight campers were surveyed on the Allegheny National Forest to determine their knowledge of rules governing recreation behavior. Most of them were uninformed about the rules. Results of the study suggest that previous camping experience, age, camping style, and residence significantly affect knowledge of rules. Campers who received rule brochures or...

  15. The rule of law

    Directory of Open Access Journals (Sweden)

    Besnik Murati

    2015-07-01

    Full Text Available The state as an international entity and its impact on the individual’s right has been and still continues to be a crucial factor in the relationship between private and public persons. States vary in terms of their political system, however, democratic states are based on the separation of powers and human rights within the state. Rule of law is the product of many actors in a state, including laws, individuals, society, political system, separation of powers, human rights, the establishment of civil society, the relationship between law and the individual, as well as, individual-state relations. Purpose and focus of this study is the importance of a functioning state based on law, characteristics of the rule of law, separation of powers and the basic concepts of the rule of law.

  16. Robert's rules of order

    CERN Document Server

    Robert, Henry M; Balch, Thomas J; Seabold, Daniel E; Gerber, Shmuel

    2011-01-01

    The only authorized edition of the classic work on parliamentary procedure, with new and enhanced features, including how to conduct electronic meetings. Robert's Rules of Order is the book on parliamentary procedure for parliamentarians and anyone involved in an organization, association, club, or group and the authoritative guide to smooth, orderly, and fairly conducted meetings and assemblies. This newly revised edition is the only book on parliamentary procedure to have been updated since 1876 under the continuing program of review established by General Henry M. Robert himself, in cooperation with the official publisher of Robert's Rules. The eleventh edition has been thoroughly revised to address common inquiries and incorporate new rules, interpretations, and procedures made necessary by the evolution of parliamentary procedure, including new material relating to electronic communication and "electronic meetings."

  17. Engineering and Implementing an Executive-Level Communication Plan in a Global Professional Environment: A Case Study

    Directory of Open Access Journals (Sweden)

    Bridgette Lipman

    2015-06-01

    Full Text Available Communication within organisations in a global environment requires effective internal and strategic planning at the executive level. Previous studies indicate that measurement is a key factor in assessing the needs and success of global communication within an organisation. Survey questions were used to measure satisfaction responses from 650 local and 110 global employees in a technology division of a large manufacturing company. In this case study, employees expressed the need to connect team members through face-to-face meetings, employee webcast meetings, web chat forums, and an updated employee networking site. The findings formed the foundations for recommendations for strategy, objectives, and tactics within the organisation.

  18. Inference rule and problem solving

    Energy Technology Data Exchange (ETDEWEB)

    Goto, S

    1982-04-01

    Intelligent information processing signifies an opportunity of having man's intellectual activity executed on the computer, in which inference, in place of ordinary calculation, is used as the basic operational mechanism for such an information processing. Many inference rules are derived from syllogisms in formal logic. The problem of programming this inference function is referred to as a problem solving. Although logically inference and problem-solving are in close relation, the calculation ability of current computers is on a low level for inferring. For clarifying the relation between inference and computers, nonmonotonic logic has been considered. The paper deals with the above topics. 16 references.

  19. Cosmic Sum Rules

    DEFF Research Database (Denmark)

    T. Frandsen, Mads; Masina, Isabella; Sannino, Francesco

    2011-01-01

    We introduce new sum rules allowing to determine universal properties of the unknown component of the cosmic rays and show how it can be used to predict the positron fraction at energies not yet explored by current experiments and to constrain specific models.......We introduce new sum rules allowing to determine universal properties of the unknown component of the cosmic rays and show how it can be used to predict the positron fraction at energies not yet explored by current experiments and to constrain specific models....

  20. Engineering zonal cartilaginous tissue by modulating oxygen levels and mechanical cues through the depth of infrapatellar fat pad stem cell laden hydrogels.

    Science.gov (United States)

    Luo, Lu; O'Reilly, Adam R; Thorpe, Stephen D; Buckley, Conor T; Kelly, Daniel J

    2017-09-01

    Engineering tissues with a structure and spatial composition mimicking those of native articular cartilage (AC) remains a challenge. This study examined if infrapatellar fat pad-derived stem cells (FPSCs) can be used to engineer cartilage grafts with a bulk composition and a spatial distribution of matrix similar to the native tissue. In an attempt to mimic the oxygen gradients and mechanical environment within AC, FPSC-laden hydrogels (either 2 mm or 4 mm in height) were confined to half of their thickness and/or subjected to dynamic compression (DC). Confining FPSC-laden hydrogels was predicted to accentuate the gradient in oxygen tension through the depth of the constructs (higher in the top and lower in the bottom), leading to enhanced glycosaminoglycan (GAG) and collagen synthesis in 2 mm high tissues. When subjected to DC alone, both GAG and collagen accumulation increased within 2 mm high unconfined constructs. Furthermore, the dynamic modulus of constructs increased from 0.96 MPa to 1.45 MPa following the application of DC. There was no synergistic benefit of coupling confinement and DC on overall levels of matrix accumulation; however in all constructs, irrespective of their height, the combination of these boundary conditions led to the development of engineered tissues that spatially best resembled native AC. The superficial region of these constructs mimicked that of native tissue, staining weakly for GAG, strongly for type II collagen, and in 4 mm high tissues more intensely for proteoglycan 4 (lubricin). This study demonstrated that FPSCs respond to joint-like environmental conditions by producing cartilage tissues mimicking native AC. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  1. Laboratory scale vitrification of low-level radioactive nitrate salts and soils from the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Shaw, P.; Anderson, B.

    1993-07-01

    INEL has radiologically contaminated nitrate salt and soil waste stored above and below ground in Pad A and the Acid Pit at the Radioactive Waste Management Complex. Pad A contain uranium and transuranic contaminated potassium and sodium nitrate salts generated from dewatered waste solutions at the Rocky Flats Plant. The Acid Pit was used to dispose of liquids containing waste mineral acids, uranium, nitrate, chlorinated solvents, and some mercury. Ex situ vitrification is a high temperature destruction of nitrates and organics and immobilizes hazardous and radioactive metals. Laboratory scale melting of actual radionuclides containing INEL Pad A nitrate salts and Acid Pit soils was performed. The salt/soil/additive ratios were varied to determine the range of glass compositions (resulted from melting different wastes); maximize mass and volume reduction, durability, and immobilization of hazardous and radioactive metals; and minimize viscosity and offgas generation for wastes prevalent at INEL and other DOE sites. Some mixtures were spiked with additional hazardous and radioactive metals. Representative glasses were leach tested and showed none. Samples spiked with transuranic showed low nuclide leaching. Wasteforms were two to three times bulk densities of the salt and soil. Thermally co-processing soils and salts is an effective remediation method for destroying nitrate salts while stabilizing the radiological and hazardous metals they contain. The measured durability of these low-level waste glasses approached those of high-level waste glasses. Lab scale vitrification of actual INEL contaminated salts and soils was performed at General Atomics Laboratory as part of the INEL Waste Technology Development and Environmental Restoration within the Buried Waste Integrated Demonstration Program

  2. Emotional display rules as work unit norms: a multilevel analysis of emotional labor among nurses.

    Science.gov (United States)

    Diefendorff, James M; Erickson, Rebecca J; Grandey, Alicia A; Dahling, Jason J

    2011-04-01

    Emotional labor theory has conceptualized emotional display rules as shared norms governing the expression of emotions at work. Using a sample of registered nurses working in different units of a hospital system, we provided the first empirical evidence that display rules can be represented as shared, unit-level beliefs. Additionally, controlling for the influence of dispositional affectivity, individual-level display rule perceptions, and emotion regulation, we found that unit-level display rules are associated with individual-level job satisfaction. We also showed that unit-level display rules relate to burnout indirectly through individual-level display rule perceptions and emotion regulation strategies. Finally, unit-level display rules also interacted with individual-level dispositional affectivity to predict employee use of emotion regulation strategies. We discuss how future research on emotional labor and display rules, particularly in the health care setting, can build on these findings.

  3. The influences of scientific information on the growing in opinion for high level waste repository. Focusing on education in civil engineering course

    International Nuclear Information System (INIS)

    Amemiya, Kiyoshi; Chijimatsu, Masakazu

    2002-01-01

    In this research, survey of awareness and attitude to high level radioactive waste (HLW) disposal on 36 students of a postgraduate course was conducted. They have been studying civil and rock engineering, so they belong to 'the Group' that acquires high education, culture and faculty to understand the science in geological disposal of HLW. First of all the awareness of danger or safety to HLW disposal was examined. Some 23% regard HLW disposal as safe, on the contrary 60% feel danger. This is similar to the awareness of the average public. And some 72% think that HLW should be disposal, but only 6% agree the repository in their town. It shows that the Group of high education has a tendency of calmly understand the necessity of disposal, but they also have a nature so-called 'not in my back yard (NIMBY)'. After that, the students were divided in two groups. Then, one group received information from the promoter, and another received information from opponents. The result of second questionnaire shows that the awareness of danger is affected strongly by given information even in this Group, but they become thoughtful and prudent in their opinion and decision-making as increasing information. Finally in this paper it is studied that 'what is the role of education of civil engineering?' and 'what is key issue in R and D of HLW disposal?' considering Public Acceptance. (author)

  4. Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 2. Engineering technology for geological disposal

    International Nuclear Information System (INIS)

    1999-11-01

    Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the deep geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, part 2 of the progress report, concerns engineering aspect with reference to Japanese geological disposal plan, according to which the vitrified HLW will be disposed of into a deep, stable rock mass with thick containers and surrounding buffer materials at the depth of several hundred meters. It discusses on multi-barrier systems consisting of a series of engineered and natural barriers that will isolate radioactive nuclides effectively and retard their migrations to the biosphere environment. Performance of repository components, including specifications of containers for vitrified HLW and their overpacks under design as well as buffer material such as Japanese bentonite to be placed in between are described referring also to such possible problems as corrosion arising from the supposed system. It also presents plans and designs for underground disposal facilities, and the presumed management of the underground facilities. (Ohno, S.)

  5. Air-fuel ratio control of a lean burn Si engine using fuzzy self tuning method

    International Nuclear Information System (INIS)

    Akhlaghi, M.; Bakhtiari Nejad, F.; Azadi, S.

    2000-01-01

    Reducing the exhaust emission of an spark ignition engine by means of engine modifications requires consideration of the effects of these modifications on the variations of crankshaft torque and the engine roughness respectively. Only if the roughness does not exceed a certain level the vehicle do not begin to surge. This paper presents a method for controlling the air-fuel ratio for a lean burn engine. Fuzzy rules and reasoning are utilized on-line to determine the control parameters. The main advantages of this method are simple structure and robust performance in a wide range of operating conditions. A non-linear model of an Si engine with the engine torque irregularity simulation is used in this study

  6. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 53: From student to entry-level professional: Examining the technical communications practices of early career-stage US aerospace engineers and scientists

    Science.gov (United States)

    Pinelli, Thomas E.; Holloway, Karen; Barclay, Rebecca O.; Kennedy, John M.

    1995-01-01

    Studies indicate that communications and information-related activities take up a substantial portion of an engineer's work week; therefore, effective communications and information-use skills are one of the key engineering competencies that early career-stage aerospace engineers and scientists must possess to be successful. Feedback from industry rates communications and information-use skills high in terms of their importance to engineering practice; however, this same feedback rates the communications and information-use skills of early career-stage engineers low. To gather adequate and generalizable data about the communications and information-related activities of entry-level aerospace engineers and scientists, we surveyed 264 members of the AIAA who have no more than 1-5 years of aerospace engineering work experience. To learn more about the concomitant communications norms, we compared the results of this study with data (1,673 responses) we collected from student members of the AIAA and with data (341 responses) we collected from a study of aerospace engineering professionals. In this paper, we report selected results from these studies that focused on the communications practices and information-related activities of early career-stage U.S. aerospace engineers and scientists in the workplace.

  7. Engineering Encounters: Engineering Adaptations

    Science.gov (United States)

    Gatling, Anne; Vaughn, Meredith Houle

    2015-01-01

    Engineering is not a subject that has historically been taught in elementary schools, but with the emphasis on engineering in the "Next Generation Science Standards," curricula are being developed to explicitly teach engineering content and design. However, many of the scientific investigations already conducted with students have…

  8. Cramer's Rule Revisited

    Science.gov (United States)

    Ayoub, Ayoub B.

    2005-01-01

    In 1750, the Swiss mathematician Gabriel Cramer published a well-written algebra book entitled "Introduction a l'Analyse des Lignes Courbes Algebriques." In the appendix to this book, Cramer gave, without proof, the rule named after him for solving a linear system of equations using determinants (Kosinki, 2001). Since then several derivations of…

  9. Crispen's Five Antivirus Rules.

    Science.gov (United States)

    Crispen, Patrick Douglas

    2000-01-01

    Explains five rules to protect computers from viruses. Highlights include commercial antivirus software programs and the need to upgrade them periodically (every year to 18 months); updating virus definitions at least weekly; scanning attached files from email with antivirus software before opening them; Microsoft Word macro protection; and the…

  10. Staff rules and regulations

    CERN Multimedia

    HR Department

    2007-01-01

    The 11th edition of the Staff Rules and Regulations, dated 1 January 2007, adopted by the Council and the Finance Committee in December 2006, is currently being distributed to departmental secretariats. The Staff Rules and Regulations, together with a summary of the main modifications made, will be available, as from next week, on the Human Resources Department's intranet site: http://cern.ch/hr-web/internal/admin_services/rules/default.asp The main changes made to the Staff Rules and Regulations stem from the five-yearly review of employment conditions of members of the personnel. The changes notably relate to: the categories of members of the personnel (e.g. removal of the local staff category); the careers structure and the merit recognition system; the non-residence, installation and re-installation allowances; the definition of family, family allowances and family-related leave; recognition of partnerships; education fees. The administrative circulars, some of which are being revised following the m...

  11. Rules of (Student) Engagement

    Science.gov (United States)

    Buskist, William; Busler, Jessica N.; Kirby, Lauren A. J.

    2018-01-01

    Teachers often think of student engagement in terms of hands-on activities that get students involved in their courses. They seldom consider the larger aspects of the teaching--learning environment that often influence the extent to which students are willing to become engaged in their coursework. In this chapter, we describe five "rules of…

  12. Ruled Laguerre minimal surfaces

    KAUST Repository

    Skopenkov, Mikhail; Pottmann, Helmut; Grohs, Philipp

    2011-01-01

    A Laguerre minimal surface is an immersed surface in ℝ 3 being an extremal of the functional ∫ (H 2/K-1)dA. In the present paper, we prove that the only ruled Laguerre minimal surfaces are up to isometry the surfaces ℝ (φλ) = (Aφ, Bφ, Cφ + D cos 2φ

  13. Ten-day rule

    International Nuclear Information System (INIS)

    Knox, E.G.; Stewart, A.M.; Kneale, G.W.; Gilman, E.A.

    1987-01-01

    The authors argue against R.H. Mole's paper (Lancet, Dec. 12 1987), supporting the relaxation of ICRP recommendations and the DHSS decision to withdraw the 10 day rule in relation to diagnostic radiography for menstruating women, and draw attention to the recent refinement of estimates of the enhanced risk of childhood cancers, following diagnostic radiography during pregnancy. (U.K.)

  14. TEDXCERN BREAKS THE RULES

    CERN Multimedia

    CERN, Bulletin

    2015-01-01

    On Friday, 9 October, TEDxCERN brought together 14 ‘rule-breakers’ to explore ideas that push beyond the boundaries of academia. They addressed a full house of 600 audience members, as well as thousands watching the event online.

  15. C-Band Airport Surface Communications System Engineering-Initial High-Level Safety Risk Assessment and Mitigation

    Science.gov (United States)

    Zelkin, Natalie; Henriksen, Stephen

    2011-01-01

    This document is being provided as part of ITT's NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract: "New ATM Requirements--Future Communications, C-Band and L-Band Communications Standard Development." ITT has completed a safety hazard analysis providing a preliminary safety assessment for the proposed C-band (5091- to 5150-MHz) airport surface communication system. The assessment was performed following the guidelines outlined in the Federal Aviation Administration Safety Risk Management Guidance for System Acquisitions document. The safety analysis did not identify any hazards with an unacceptable risk, though a number of hazards with a medium risk were documented. This effort represents an initial high-level safety hazard analysis and notes the triggers for risk reassessment. A detailed safety hazards analysis is recommended as a follow-on activity to assess particular components of the C-band communication system after the profile is finalized and system rollout timing is determined. A security risk assessment has been performed by NASA as a parallel activity. While safety analysis is concerned with a prevention of accidental errors and failures, the security threat analysis focuses on deliberate attacks. Both processes identify the events that affect operation of the system; and from a safety perspective the security threats may present safety risks.

  16. Engineering studies: high-level radioactive waste repositories task 3 - review of underground handling and emplacement. 1. Executive summary

    Energy Technology Data Exchange (ETDEWEB)

    1981-02-01

    The report reviews proposals for transport, handling and emplacement of high-level radioactive waste in an underground repository with particular reference to: waste block size and configuration; self-shielded or partially-shielded block; stages of disposal; transport by road/rail to repository site; handling techniques within repository; emplacement in vertical holes or horizontal tunnels; repository access by adit, incline or shaft; conventional and radiological safety; costs; and major areas of uncertainty requiring research or development. In carrying out this programme due attention was given to work already carried out both in the U.K. and overseas and where appropriate comparisons with this work have been made to substantiate and explain the observations made in this report. The examination and use of this previous work however has been confined to those proposals which were considered capable of meeting the basic design criterion for a U.K. based repository, that the maximum temperature achieved by the host rock should not exceed 100/sup 0/C.

  17. Initial performance assessment of the disposal of spent nuclear fuel and high-level waste stored at Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Rechard, R.P.

    1993-12-01

    This performance assessment characterized plausible treatment options conceived by the Idaho National Engineering Laboratory (INEL) for its spent fuel and high-level radioactive waste and then modeled the performance of the resulting waste forms in two hypothetical, deep, geologic repositories: one in bedded salt and the other in granite. The results of the performance assessment are intended to help guide INEL in its study of how to prepare wastes and spent fuel for eventual permanent disposal. This assessment was part of the Waste Management Technology Development Program designed to help the US Department of Energy develop and demonstrate the capability to dispose of its nuclear waste. Although numerous caveats must be placed on the results, the general findings were as follows: Though the waste form behavior depended upon the repository type, all current and proposed waste forms provided acceptable behavior in the salt and granite repositories

  18. Initial performance assessment of the disposal of spent nuclear fuel and high-level waste stored at Idaho National Engineering Laboratory. Volume 1, Methodology and results

    Energy Technology Data Exchange (ETDEWEB)

    Rechard, R.P. [ed.

    1993-12-01

    This performance assessment characterized plausible treatment options conceived by the Idaho National Engineering Laboratory (INEL) for its spent fuel and high-level radioactive waste and then modeled the performance of the resulting waste forms in two hypothetical, deep, geologic repositories: one in bedded salt and the other in granite. The results of the performance assessment are intended to help guide INEL in its study of how to prepare wastes and spent fuel for eventual permanent disposal. This assessment was part of the Waste Management Technology Development Program designed to help the US Department of Energy develop and demonstrate the capability to dispose of its nuclear waste. Although numerous caveats must be placed on the results, the general findings were as follows: Though the waste form behavior depended upon the repository type, all current and proposed waste forms provided acceptable behavior in the salt and granite repositories.

  19. A preliminary parametric performance assessment for the disposal of alpha-contaminated mixed low-level waste stored at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Smith, T.H.; Anderson, G.L.; Myers, J.

    1995-01-01

    A preliminary parametric performance assessment (PA) has been performed of potential waste disposal systems for alpha-contaminated mixed low-level waste (ALLW) currently stored at the Idaho National Engineering Laboratory. The radionuclide-confinement performance of treated ALLW in various final waste forms, in various disposal locations, and under various assumptions was evaluated. Compliance with performance objectives was assessed for the undisturbed waste scenario and for intrusion scenarios. Some combinations of final waste form, disposal site, and environmental transport assumptions lead to calculated does that comply with the performance objectives, while others do not. The results will help determine the optimum degree of ALLW immobilization to satisfy the performance objectives while minimizing cost

  20. Organizational Knowledge Transfer Using Ontologies and a Rule-Based System

    Science.gov (United States)

    Okabe, Masao; Yoshioka, Akiko; Kobayashi, Keido; Yamaguchi, Takahira

    In recent automated and integrated manufacturing, so-called intelligence skill is becoming more and more important and its efficient transfer to next-generation engineers is one of the urgent issues. In this paper, we propose a new approach without costly OJT (on-the-job training), that is, combinational usage of a domain ontology, a rule ontology and a rule-based system. Intelligence skill can be decomposed into pieces of simple engineering rules. A rule ontology consists of these engineering rules as primitives and the semantic relations among them. A domain ontology consists of technical terms in the engineering rules and the semantic relations among them. A rule ontology helps novices get the total picture of the intelligence skill and a domain ontology helps them understand the exact meanings of the engineering rules. A rule-based system helps domain experts externalize their tacit intelligence skill to ontologies and also helps novices internalize them. As a case study, we applied our proposal to some actual job at a remote control and maintenance office of hydroelectric power stations in Tokyo Electric Power Co., Inc. We also did an evaluation experiment for this case study and the result supports our proposal.

  1. Adaptive Gas Turbine Engine Control for Deterioration Compensation Due to Aging

    Science.gov (United States)

    Litt, Jonathan S.; Parker, Khary I.; Chatterjee, Santanu

    2003-01-01

    This paper presents an ad hoc adaptive, multivariable controller tuning rule that compensates for a thrust response variation in an engine whose performance has been degraded though use and wear. The upset appears when a large throttle transient is performed such that the engine controller switches from low-speed to high-speed mode. A relationship was observed between the level of engine degradation and the overshoot in engine temperature ratio, which was determined to cause the thrust response variation. This relationship was used to adapt the controller. The method is shown to work very well up to the operability limits of the engine. Additionally, since the level of degradation can be estimated from sensor data, it would be feasible to implement the adaptive control algorithm on-line.

  2. Engineering Education for a New Era

    Science.gov (United States)

    Ohgaki, Shinichiro

    Engineering education is composed of five components, the idea what engineering education ought to be, the knowledge in engineering fields, those who learn engineering, those who teach engineering and the stakeholders in engineering issues. The characteristics of all these five components are changing with the times. When we consider the engineering education for the next era, we should analyze the changes of all five components. Especially the knowledge and tools in engineering fields has been expanding, and advanced science and technology is casting partly a dark shadow on the modern convenient life. Moral rules or ethics for developing new products and engineering systems are now regarded as most important in engineering fields. All those who take the responsibility for engineering education should understand the change of all components in engineering education and have a clear grasp of the essence of engineering for sustainable society.

  3. Who Is Doing the Engineering, the Student or the Teacher? The Development and Use of a Rubric to Categorize Level of Design for the Elementary Classroom

    Science.gov (United States)

    Nadelson, Louis S.; Pfiester, Joshua; Callahan, Janet; Pyke, Patricia

    2015-01-01

    Science, technology, engineering, and mathematics (STEM) professional development for K-5 teachers often includes engineering design as a focus. Because engineering applications provide perspective to both teachers and their students in terms of how mathematic and scientific principles are employed to solve real-world problems (Baine, 2004; Roden,…

  4. Design rules for RCA self-aligned silicon-gate CMOS/SOS process

    Science.gov (United States)

    1977-01-01

    The CMOS/SOS design rules prepared by the RCA Solid State Technology Center (SSTC) are described. These rules specify the spacing and width requirements for each of the six design levels, the seventh level being used to define openings in the passivation level. An associated report, entitled Silicon-Gate CMOS/SOS Processing, provides further insight into the usage of these rules.

  5. Verification of business rules programs

    CERN Document Server

    Silva, Bruno Berstel-Da

    2013-01-01

    Rules represent a simplified means of programming, congruent with our understanding of human brain constructs. With the advent of business rules management systems, it has been possible to introduce rule-based programming to nonprogrammers, allowing them to map expert intent into code in applications such as fraud detection, financial transactions, healthcare, retail, and marketing. However, a remaining concern is the quality, safety, and reliability of the resulting programs.  This book is on business rules programs, that is, rule programs as handled in business rules management systems. Its

  6. Welding engineering manual for constructing engineers. Pt. 2

    International Nuclear Information System (INIS)

    Neumann, A.

    1986-01-01

    The manual is a real treasure trove of knowledge and experience for the statics expert, the constructing engineer, and the welding engineer, who have to do with design and dimensioning of welding engineering work for steel structures, bridges, boilers, vessels, and pipes. Many practical examples are given together with numerous data that provide helpful information for the task of technical and economic design and dimensioning. Determination of efficient and appropriate cross-sectional dimensions and materials is the main goal of the manual. Structural steel engineering and installations subject to monitoring and inspection such as boilers, pipings, pressure vessels, and nuclear installations are the subject fields dealt with in separate chapters. The dimensioning rules presented are based on the regulations and technical codes valid in the GDR and the FRG. The catalogue of technical rules of the FRG concerning structural steel engineering and installations as above are given in supplementary chapters. (orig./HP) [de

  7. A generalization of Hamilton's rule--love others how much?

    Science.gov (United States)

    Alger, Ingela; Weibull, Jörgen W

    2012-04-21

    According to Hamilton's (1964a, b) rule, a costly action will be undertaken if its fitness cost to the actor falls short of the discounted benefit to the recipient, where the discount factor is Wright's index of relatedness between the two. We propose a generalization of this rule, and show that if evolution operates at the level of behavior rules, rather than directly at the level of actions, evolution will select behavior rules that induce a degree of cooperation that may differ from that predicted by Hamilton's rule as applied to actions. In social dilemmas there will be less (more) cooperation than under Hamilton's rule if the actions are strategic substitutes (complements). Our approach is based on natural selection, defined in terms of personal (direct) fitness, and applies to a wide range of pairwise interactions. Copyright © 2011 Elsevier Ltd. All rights reserved.

  8. Exhibit celebrates five decades of women in engineering

    OpenAIRE

    Gilbert, Karen

    2007-01-01

    "Petticoats and Slide Rules," a historical exhibit on women in engineering from the Society of Women Engineers (SWE), is currently on display in the lobby of Hancock 100 and will remain at Virginia Tech through March of 2007.

  9. Convention on nuclear safety. Rules of procedure and financial rules

    International Nuclear Information System (INIS)

    1998-01-01

    The document presents the Rules of Procedure and Financial Rules that apply mutatis mutandis to any meeting of the Contracting Parties to the Convention on Nuclear Safety (INFCIRC/449) convened in accordance with Chapter 3 of the Convention. It includes four parts: General provisions, Preparatory process for review meetings, Review meetings, and Amendment and interpretation of rules

  10. A Methodology for Multiple Rule System Integration and Resolution Within a Singular Knowledge Base

    Science.gov (United States)

    Kautzmann, Frank N., III

    1988-01-01

    Expert Systems which support knowledge representation by qualitative modeling techniques experience problems, when called upon to support integrated views embodying description and explanation, especially when other factors such as multiple causality, competing rule model resolution, and multiple uses of knowledge representation are included. A series of prototypes are being developed to demonstrate the feasibility of automating the process of systems engineering, design and configuration, and diagnosis and fault management. A study involves not only a generic knowledge representation; it must also support multiple views at varying levels of description and interaction between physical elements, systems, and subsystems. Moreover, it will involve models of description and explanation for each level. This multiple model feature requires the development of control methods between rule systems and heuristics on a meta-level for each expert system involved in an integrated and larger class of expert system. The broadest possible category of interacting expert systems is described along with a general methodology for the knowledge representation and control of mutually exclusive rule systems.

  11. Initial performance assessment of the disposal of spent nuclear fuel and high-level waste stored at Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Rechard, R.P.

    1993-12-01

    This performance assessment characterized plausible treatment options conceived by the Idaho National Engineering Laboratory (INEL) for its spent fuel and high-level radioactive waste and then modeled the performance of the resulting waste forms in two hypothetical, deep, geologic repositories: one in bedded salt and the other in granite. The results of the performance assessment are intended to help guide INEL in its study of how to prepare wastes and spent fuel for eventual permanent disposal. This assessment was part of the Waste Management Technology Development Program designed to help the US Department of Energy develop and demonstrate the capability to dispose of its nuclear waste, as mandated by the Nuclear Waste Policy Act of 1982. The waste forms comprised about 700 metric tons of initial heavy metal (or equivalent units) stored at the INEL: graphite spent fuel, experimental low enriched and highly enriched spent fuel, and high-level waste generated during reprocessing of some spent fuel. Five different waste treatment options were studied; in the analysis, the options and resulting waste forms were analyzed separately and in combination as five waste disposal groups. When the waste forms were studied in combination, the repository was assumed to also contain vitrified high-level waste from three DOE sites for a common basis of comparison and to simulate the impact of the INEL waste forms on a moderate-sized repository, The performance of the waste form was assessed within the context of a whole disposal system, using the U.S. Environmental Protection Agency's Environmental Radiation Protection Standards for Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes, 40 CFR 191, promulgated in 1985. Though the waste form behavior depended upon the repository type, all current and proposed waste forms provided acceptable behavior in the salt and granite repositories

  12. Initial performance assessment of the disposal of spent nuclear fuel and high-level waste stored at Idaho National Engineering Laboratory. Volume 2: Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Rechard, R.P. [ed.

    1993-12-01

    This performance assessment characterized plausible treatment options conceived by the Idaho National Engineering Laboratory (INEL) for its spent fuel and high-level radioactive waste and then modeled the performance of the resulting waste forms in two hypothetical, deep, geologic repositories: one in bedded salt and the other in granite. The results of the performance assessment are intended to help guide INEL in its study of how to prepare wastes and spent fuel for eventual permanent disposal. This assessment was part of the Waste Management Technology Development Program designed to help the US Department of Energy develop and demonstrate the capability to dispose of its nuclear waste, as mandated by the Nuclear Waste Policy Act of 1982. The waste forms comprised about 700 metric tons of initial heavy metal (or equivalent units) stored at the INEL: graphite spent fuel, experimental low enriched and highly enriched spent fuel, and high-level waste generated during reprocessing of some spent fuel. Five different waste treatment options were studied; in the analysis, the options and resulting waste forms were analyzed separately and in combination as five waste disposal groups. When the waste forms were studied in combination, the repository was assumed to also contain vitrified high-level waste from three DOE sites for a common basis of comparison and to simulate the impact of the INEL waste forms on a moderate-sized repository, The performance of the waste form was assessed within the context of a whole disposal system, using the U.S. Environmental Protection Agency`s Environmental Radiation Protection Standards for Management and Disposal of Spent Nuclear Fuel, High-Level and Transuranic Radioactive Wastes, 40 CFR 191, promulgated in 1985. Though the waste form behavior depended upon the repository type, all current and proposed waste forms provided acceptable behavior in the salt and granite repositories.

  13. Consistence of Network Filtering Rules

    Institute of Scientific and Technical Information of China (English)

    SHE Kun; WU Yuancheng; HUANG Juncai; ZHOU Mingtian

    2004-01-01

    The inconsistence of firewall/VPN(Virtual Private Network) rule makes a huge maintainable cost.With development of Multinational Company,SOHO office,E-government the number of firewalls/VPN will increase rapidly.Rule table in stand-alone or network will be increased in geometric series accordingly.Checking the consistence of rule table manually is inadequate.A formal approach can define semantic consistence,make a theoretic foundation of intelligent management about rule tables.In this paper,a kind of formalization of host rules and network ones for auto rule-validation based on SET theory were proporsed and a rule validation scheme was defined.The analysis results show the superior performance of the methods and demonstrate its potential for the intelligent management based on rule tables.

  14. Rule-Based Event Processing and Reaction Rules

    Science.gov (United States)

    Paschke, Adrian; Kozlenkov, Alexander

    Reaction rules and event processing technologies play a key role in making business and IT / Internet infrastructures more agile and active. While event processing is concerned with detecting events from large event clouds or streams in almost real-time, reaction rules are concerned with the invocation of actions in response to events and actionable situations. They state the conditions under which actions must be taken. In the last decades various reaction rule and event processing approaches have been developed, which for the most part have been advanced separately. In this paper we survey reaction rule approaches and rule-based event processing systems and languages.

  15. Proof Rules for Recursive Procedures

    NARCIS (Netherlands)

    Hesselink, Wim H.

    1993-01-01

    Four proof rules for recursive procedures in a Pascal-like language are presented. The main rule deals with total correctness and is based on results of Gries and Martin. The rule is easier to apply than Martin's. It is introduced as an extension of a specification format for Pascal-procedures, with

  16. Endogeneously arising network allocation rules

    NARCIS (Netherlands)

    Slikker, M.

    2006-01-01

    In this paper we study endogenously arising network allocation rules. We focus on three allocation rules: the Myerson value, the position value and the component-wise egalitarian solution. For any of these three rules we provide a characterization based on component efficiency and some balanced

  17. Deployable Engine Air Brake

    Science.gov (United States)

    2014-01-01

    On approach, next-generation aircraft are likely to have airframe noise levels that are comparable to or in excess of engine noise. ATA Engineering, Inc. (ATA) is developing a novel quiet engine air brake (EAB), a device that generates "equivalent drag" within the engine through stream thrust reduction by creating a swirling outflow in the turbofan exhaust nozzle. Two Phase II projects were conducted to mature this technology: (1) a concept development program (CDP) and (2) a system development program (SDP).

  18. Final Rule for Control of Air Pollution From Motor Vehicles and New Motor Vehicle Engines; Modification of Federal Onboard Diagnostic Regulations for Light-Duty Vehicles and Light-Duty Trucks; Extension of Acceptance of California OBD

    Science.gov (United States)

    This action finalizes modifications to the federal on-board diagnostics regulations, including: harmonizing the emission levels above which a component or system is considered malfunctioning with those of the California Air Resources Board (CARB).

  19. Engineering Encounters: Reverse Engineering

    Science.gov (United States)

    McGowan, Veronica Cassone; Ventura, Marcia; Bell, Philip

    2017-01-01

    This column presents ideas and techniques to enhance your science teaching. This month's issue shares information on how students' everyday experiences can support science learning through engineering design. In this article, the authors outline a reverse-engineering model of instruction and describe one example of how it looked in our fifth-grade…

  20. The good engineer: giving virtue its due in engineering ethics.

    Science.gov (United States)

    Harris, Charles E

    2008-06-01

    During the past few decades, engineering ethics has been oriented towards protecting the public from professional misconduct by engineers and from the harmful effects of technology. This "preventive ethics" project has been accomplished primarily by means of the promulgation of negative rules. However, some aspects of engineering professionalism, such as (1) sensitivity to risk (2) awareness of the social context of technology, (3) respect for nature, and (4) commitment to the public good, cannot be adequately accounted for in terms of rules, certainly not negative rules. Virtue ethics is a more appropriate vehicle for expressing these aspects of engineering professionalism. Some of the unique features of virtue ethics are the greater place it gives for discretion and judgment and also for inner motivation and commitment. Four of the many professional virtues that are important for engineers correspond to the four aspects of engineering professionalism listed above. Finally, the importance of the humanities and social sciences in promoting these virtues suggests that these disciplines are crucial in the professional education of engineers.

  1. Business rules for creating process flexibility : Mapping RIF rules and BDI rules

    NARCIS (Netherlands)

    Gong, Y.; Overbeek, S.J.; Janssen, M.

    2011-01-01

    Business rules and software agents can be used for creating flexible business processes. The Rule Interchange Format (RIF) is a new W3C recommendation standard for exchanging rules among disparate systems. Yet, the impact that the introduction of RIF has on the design of flexible business processes

  2. Post Rule of Law

    DEFF Research Database (Denmark)

    Carlson, Kerstin Bree

    2016-01-01

    The value of developing hybrid international criminal procedure (ICP) is that it is arguably inclusive (representing two major legal traditions) and distinct from any domestic system, thus creating a separate, sui generis realm for international criminal law (ICL) jurists to meet. Since its...... addresses the practice of hybridity in ICP, drawing examples from the construction and evolution of hybrid procedure at the International Criminal Tribunal for the Former Yugoslavia (ICTY), to argue that the hybridity practiced by international criminal tribunals renders them ‘post rule of law’ institutions...

  3. OZI rule and instantons

    International Nuclear Information System (INIS)

    Nowak, M.A.; Zahed, I.; Verbaarschot, J.J.M.

    1989-01-01

    We investigate the effects of strangeness mixing in the QCD vacuum described as a quantum disordered phase of instantons and anti-instantons. We find that the constituent mass of the light quarks is a decreasing function of the current quark masses, and that its mass is almost insensitive to the value of the strange quark mass. Our results cannot account for a breach in the OZI rule in the vacuum. The relevance of this result for the amount of santi s pairs in the nucleon and the pion-nucleon sigma term is discussed. (orig.)

  4. Description logic rules

    CERN Document Server

    Krötzsch, M

    2010-01-01

    Ontological modelling today is applied in many areas of science and technology,including the Semantic Web. The W3C standard OWL defines one of the most important ontology languages based on the semantics of description logics. An alternative is to use rule languages in knowledge modelling, as proposed in the W3C's RIF standard. So far, it has often been unclear how to combine both technologies without sacrificing essential computational properties. This book explains this problem and presents new solutions that have recently been proposed. Extensive introductory chapters provide the necessary

  5. Safety rule evolution for future LMFBRs

    International Nuclear Information System (INIS)

    Justin, F.; Wiesner

    1986-06-01

    After safety rules for operating reactors and for built reactors in France and Germany, this report presents the main points of the safety rules for future reactors. It is generally agreed that future LMFBRs will have to show the same safety level as other commercial nuclear power plants. The demonstration is to be partly based on deterministic criteria, or ''safety rules'', and partly on risk considerations, for rare events. In that respect, a high effort on preventive measures, especially to reinforce the reliability of essential safety functions (shutdown, decay heat removal) could be sufficient, if all conditions are considered. So the containment of a hypothetical core disruptive accident is no longer required. Nevertheless, low probability events gave some feedback on the SPX.2 design

  6. Creep design rules in french ''RCC-MR'' code

    International Nuclear Information System (INIS)

    Roche, H.

    1986-04-01

    In this paper, four points enlightening the originality of the ''RCC-MR'' analysis rules in the creep range will be discussed. The three first points will concern elastic analysis, the fourth one materials data. The rules given in this paper are applicable for class 1 components and level A conditions. They are given by way of illustration in a simplified form

  7. Site systems engineering: Systems engineering management plan

    Energy Technology Data Exchange (ETDEWEB)

    Grygiel, M.L. [Westinghouse Hanford Co., Richland, WA (United States)

    1996-05-03

    The Site Systems Engineering Management Plan (SEMP) is the Westinghouse Hanford Company (WHC) implementation document for the Hanford Site Systems Engineering Policy, (RLPD 430.1) and Systems Engineering Criteria Document and Implementing Directive, (RLID 430.1). These documents define the US Department of Energy (DOE), Richland Operations Office (RL) processes and products to be used at Hanford to implement the systems engineering process at the site level. This SEMP describes the products being provided by the site systems engineering activity in fiscal year (FY) 1996 and the associated schedule. It also includes the procedural approach being taken by the site level systems engineering activity in the development of these products and the intended uses for the products in the integrated planning process in response to the DOE policy and implementing directives. The scope of the systems engineering process is to define a set of activities and products to be used at the site level during FY 1996 or until the successful Project Hanford Management Contractor (PHMC) is onsite as a result of contract award from Request For Proposal DE-RP06-96RL13200. Following installation of the new contractor, a long-term set of systems engineering procedures and products will be defined for management of the Hanford Project. The extent to which each project applies the systems engineering process and the specific tools used are determined by the project`s management.

  8. Why microbes will rule the world – and our industries

    DEFF Research Database (Denmark)

    Lykke, Anne Wärme; Palsson, Bernhard; Nielsen, Jens

    2017-01-01

    Microbes have ruled the world for approximately 4 billion years. But the future actually depends on their dominance, some would argue. Why? Because microbes, as well as mammalian cells, can be engineered into producing high-value chemicals and medicine. Therefore, scientists at The Novo Nordisk...... Foundation Center for Biosustainability are hard at work developing cell factories to benefit us all....

  9. From Human Activity to Conceptual Understanding of the Chain Rule

    Science.gov (United States)

    Jojo, Zingiswa Mybert Monica; Maharaj, Aneshkumar; Brijlall, Deonarain

    2013-01-01

    This article reports on a study which investigated first year university engineering students' construction of the definition of the concept of the chain rule in differential calculus at a University of Technology in South Africa. An APOS (Action-Process-Objects-Schema) approach was used to explore conceptual understanding displayed by students in…

  10. FEBEX project: full-scale engineered barriers experiment for a deep geological repository for high level radioactive waste in crystalline host rock. Final report

    International Nuclear Information System (INIS)

    Alberdi, J.; Barcala, J. M.; Campos, R.; Cuevas, A. M.; Fernandez, E.

    2000-01-01

    FEBEX has the multiple objective of demonstrating the feasibility of manufacturing, handling and constructing the engineered barriers and of developing codes for the thermo-hydro-mechanical and thermo-hydro-geochemical performance assessment of a deep geological repository for high level radioactive wastes. These objectives require integrated theoretical and experimental development work. The experimental work consists of three parts: an in situ test, a mock-up test and a series of laboratory tests. The experiments is based on the Spanish reference concept for crystalline rock, in which the waste capsules are placed horizontally in drifts surround by high density compacted bentonite blocks. In the two large-scale tests, the thermal effects of the wastes were simulated by means of heaters; hydration was natural in the in situ test and controlled in the mock-up test. The large-scale tests, with their monitoring systems, have been in operation for more than two years. the demonstration has been achieved in the in situ test and there are great expectation that numerical models sufficiently validated for the near-field performance assessment will be achieved. (Author)

  11. Low-level waste drum staging building at Weapons Engineering Tritium Facility, TA-16, Los Alamos National Laboratory, Los Alamos, New Mexico. Environmental Assessment

    International Nuclear Information System (INIS)

    1994-08-01

    The proposed action is to place a 3 meter (m) by 4.5 m (10 ft x 15 ft) prefabricated storage building (transportainer) adjacent to the existing Weapons Engineering Tritium Facility (WETF) at Technical Area (TA-) 16, Los Alamos National Laboratory (LANL), and to use the building as a staging site for sealed 55 galllon drums of noncompactible waste contaminated with low levels of tritium (LLW). Up to eight drums of waste would be accumulated before the waste is moved by LANL Waste Management personnel to the existing on-site LLW disposal area at TA-54. The drum staging building would be placed on a bermed asphalt pad, near other existing accumulation structures for office trash and compactible LLW. The no-action alternative is to continue storing drums of LLW in the WETF laboratories where they occupy valuable work space, hamper movement of personnel and equipment, and require waste management personnel to enter those laboratories in order to remove filled drums. No new waste would be generated by implementing the proposed action; no changes or increases in WETF operations or waste production rate are anticipated as a result of staging drums of LLW outside the main laboratory building. The site for the LLW drum staging building would not impact any sensitive areas. Tritium emissions from the drums of LLW were included within the source term for normal operations at the WETF; the cumulative impacts would not be increased

  12. FEBEX project: full-scale engineered barriers experiment for a deep geological repository for high level radioactive waste in crystalline host rock

    Energy Technology Data Exchange (ETDEWEB)

    Alberid, J; Barcala, J M; Campos, R; Cuevas, A M; Fernandez, E [Ciemat. Madrid (Spain)

    2000-07-01

    FEBEX has the multiple objective of demonstrating the feasibility of manufacturing, handling and constructing the engineered barriers and of developing codes for the thermo-hydro-mechanical and thermo-hydro-geochemical performance assessment of a deep geological repository for high level radioactive wastes. These objectives require integrated theoretical and experimental development work. The experimental work consists of three parts: an in situ test, a mock-up test and a series of laboratory tests. The experiments is based on the Spanish reference concept for crystalline rock, in which the waste capsules are placed horizontally in drifts surround by high density compacted bentonite blocks. In the two large-scale tests, the thermal effects of the wastes were simulated by means of heaters; hydration was natural in the in situ test and controlled in the mock-up test. The large-scale tests, with their monitoring systems, have been in operation for more than two years. the demonstration has been achieved in the in situ test and there are great expectation that numerical models sufficiently validated for the near-field performance assessment will be achieved. (Author)

  13. Capturing, Sharing, and Discovering Product Data at a Semantic Level--Moving Forward to the Semantic Web for Advancing the Engineering Product Design Process

    Science.gov (United States)

    Zhu, Lijuan

    2011-01-01

    Along with the greater productivity that CAD automation provides nowadays, the product data of engineering applications needs to be shared and managed efficiently to gain a competitive edge for the engineering product design. However, exchanging and sharing the heterogeneous product data is still challenging. This dissertation first presents a…

  14. An improvement of tree-Rule firewall for a large network: supporting large rule size and low delay

    NARCIS (Netherlands)

    Chomsiri, Thawatchai; He, Xiangjian; Nanda, Priyadarsi; Tan, Zhiyuan

    Firewalls are important network devices which provide first hand defense against network threat. This level of defense is depended on firewall rules. Traditional firewalls, i.e., Cisco ACL, IPTABLES, Check Point and Juniper NetScreen firewall use listed rule to regulate packet flows. However, the

  15. Engineered myocardium model to study the roles of HIF-1α and HIF1A-AS1 in paracrine-only signaling under pathological level oxidative stress.

    Science.gov (United States)

    Acun, Aylin; Zorlutuna, Pinar

    2017-08-01

    Studying heart tissue is critical for understanding and developing treatments for cardiovascular diseases. In this work, we fabricated precisely controlled and biomimetic engineered model tissues to study how cell-cell and cell-matrix interactions influence myocardial cell survival upon exposure to pathological level oxidative stress. Specifically, the interactions of endothelial cells (ECs) and cardiomyocytes (CMs), and the role of hypoxia inducible factor-1α (HIF-1α), with its novel alternative regulator, HIF-1α antisense RNA1 (HIF1A-AS1), in these interactions were investigated. We encapsulated CMs in photo-crosslinkable, biomimetic hydrogels with or without ECs, then exposed to oxidative stress followed by normoxia. With precisely controlled microenvironment provided by the model tissues, cell-cell interactions were restricted to be solely through the secreted factors. CM survival after oxidative stress was significantly improved, in the presence of ECs, when cells were in the model tissues that were functionalized with cell attachment motifs. Importantly, the cardioprotective effect of ECs was reduced when HIF-1α expression was knocked down suggesting that HIF-1α is involved in cardioprotection from oxidative damage, provided through secreted factors conferred by the ECs. Using model tissues, we showed that cell survival increased with increased cell-cell communication and enhanced cell-matrix interactions. In addition, whole genome transcriptome analysis showed, for the first time to our knowledge, a possible role for HIF1A-AS1 in oxidative regulation of HIF-1α. We showed that although HIF1A-AS1 knockdown helps CM survival, its effect is overridden by CM-EC bidirectional interactions as we showed that the conditioned media taken from the CM-EC co-cultures improved CM survival, regardless of HIF1A-AS1 expression. Cardiovascular diseases, most of which are associated with oxidative stress, is the most common cause of death worldwide. Thus, understanding

  16. The Product and Quotient Rules Revisited

    Science.gov (United States)

    Eggleton, Roger; Kustov, Vladimir

    2011-01-01

    Mathematical elegance is illustrated by strikingly parallel versions of the product and quotient rules of basic calculus, with some applications. Corresponding rules for second derivatives are given: the product rule is familiar, but the quotient rule is less so.

  17. Revisions to the Clean Water Act Regulatory Definition of Discharge of Dredged Material; Final Rule

    Science.gov (United States)

    The U.S. Army Corps of Engineers (Corps) and the Environmental Protection Agency (EPA) promulgated a final rule Amending a Clean Water Act (CWA) section 404 regulation that defines the term discharge of dredged material.

  18. Hamburg rules V Hague Visby rules an English perspective

    OpenAIRE

    Tozaj Dorian; Xhelilaj Ermal

    2010-01-01

    It has often been argued for the effect of defences provided to carriers under Art IV (2) of Hague Visby Rules to almost nullify the protection guaranteed to shippers in other provisions of this convention. Therefore an all embracing universal shipper friendly convention, merely the Hamburg Rules, need be incorporated in all countries in order to address this issue and fully satisfy the intentions of the parties for the establishment of international rules in international trade

  19. NASA systems engineering handbook

    Science.gov (United States)

    Shishko, Robert; Aster, Robert; Chamberlain, Robert G.; McDuffee, Patrick; Pieniazek, Les; Rowell, Tom; Bain, Beth; Cox, Renee I.; Mooz, Harold; Polaski, Lou

    1995-06-01

    This handbook brings the fundamental concepts and techniques of systems engineering to NASA personnel in a way that recognizes the nature of NASA systems and environment. It is intended to accompany formal NASA training courses on systems engineering and project management when appropriate, and is designed to be a top-level overview. The concepts were drawn from NASA field center handbooks, NMI's/NHB's, the work of the NASA-wide Systems Engineering Working Group and the Systems Engineering Process Improvement Task team, several non-NASA textbooks and guides, and material from independent systems engineering courses taught to NASA personnel. Five core chapters cover systems engineering fundamentals, the NASA Project Cycle, management issues in systems engineering, systems analysis and modeling, and specialty engineering integration. It is not intended as a directive.

  20. Biocommodity Engineering.

    Science.gov (United States)

    Lynd; Wyman; Gerngross

    1999-10-01

    The application of biotechnology to the production of commodity products (fuels, chemicals, and materials) offering benefits in terms of sustainable resource supply and environmental quality is an emergent area of intellectual endeavor and industrial practice with great promise. Such "biocommodity engineering" is distinct from biotechnology motivated by health care at multiple levels, including economic driving forces, the importance of feedstocks and cost-motivated process engineering, and the scale of application. Plant biomass represents both the dominant foreseeable source of feedstocks for biotechnological processes as well as the only foreseeable sustainable source of organic fuels, chemicals, and materials. A variety of forms of biomass, notably many cellulosic feedstocks, are potentially available at a large scale and are cost-competitive with low-cost petroleum whether considered on a mass or energy basis, and in terms of price defined on a purchase or net basis for both current and projected mature technology, and on a transfer basis for mature technology. Thus the central, and we believe surmountable, impediment to more widespread application of biocommodity engineering is the general absence of low-cost processing technology. Technological and research challenges associated with converting plant biomass into commodity products are considered relative to overcoming the recalcitrance of cellulosic biomass (converting cellulosic biomass into reactive intermediates) and product diversification (converting reactive intermediates into useful products). Advances are needed in pretreatment technology to make cellulosic materials accessible to enzymatic hydrolysis, with increased attention to the fundamental chemistry operative in pretreatment processes likely to accelerate progress. Important biotechnological challenges related to the utilization of cellulosic biomass include developing cellulase enzymes and microorganisms to produce them, fermentation of

  1. CDMA systems capacity engineering

    CERN Document Server

    Kim, Kiseon

    2004-01-01

    This new hands-on resource tackles capacity planning and engineering issues that are crucial to optimizing wireless communication systems performance. Going beyond the system physical level and investigating CDMA system capacity at the service level, this volume is the single-source for engineering and analyzing systems capacity and resources.

  2. Rule based deterioration identification and management system

    International Nuclear Information System (INIS)

    Kataoka, S.; Pavinich, W.; Lapides, M.

    1993-01-01

    Under the sponsorship of IHI and EPRI, a rule-based screening system has been developed that can be used by utility engineers to determine which deterioration mechanisms are acting on specific LWR components, and to evaluate the efficacy of an age-related deterioration management program. The screening system was developed using the rule-based shell, NEXPERT, which provides traceability to the data sources used in the logic development. The system addresses all the deterioration mechanisms of specific metals encountered in either BWRs or PWRs. Deterioration mechanisms are listed with reasons why they may occur during the design life of LWRs, considering the plant environment, manufacturing process, service history, material chemical composition, etc. of components in a specific location of a LWR. To eliminate the evaluation of inactive deterioration quickly, a tier structure is applied to the rules. The reasons why deterioration will occur are extracted automatically by backward chaining. To reduce the amount of user input, plant environmental data are stored in files as default environmental data. (author)

  3. New Games, New Rules

    DEFF Research Database (Denmark)

    Constantiou, Ioanna; Kallinikos, Jannis

    2015-01-01

    Big data and the mechanisms by which it is produced and disseminated introduce important changes in the ways information is generated and made relevant for organizations. Big data often represents miscellaneous records of the whereabouts of large and shifting online crowds. It is frequently......, the usefulness of big data rests on their steady updatability, a condition that reduces the time span within which this data is useful or relevant. Jointly, these attributes challenge established rules of strategy making as these are manifested in the canons of procuring structured information of lasting value...... that addresses specific and long-term organizational objectives. The developments underlying big data thus seem to carry important implications for strategy making, and the data and information practices with which strategy has been associated. We conclude by placing the understanding of these changes within...

  4. Ruled Laguerre minimal surfaces

    KAUST Repository

    Skopenkov, Mikhail

    2011-10-30

    A Laguerre minimal surface is an immersed surface in ℝ 3 being an extremal of the functional ∫ (H 2/K-1)dA. In the present paper, we prove that the only ruled Laguerre minimal surfaces are up to isometry the surfaces ℝ (φλ) = (Aφ, Bφ, Cφ + D cos 2φ) + λ(sin φ, cos φ, 0), where A,B,C,D ε ℝ are fixed. To achieve invariance under Laguerre transformations, we also derive all Laguerre minimal surfaces that are enveloped by a family of cones. The methodology is based on the isotropic model of Laguerre geometry. In this model a Laguerre minimal surface enveloped by a family of cones corresponds to a graph of a biharmonic function carrying a family of isotropic circles. We classify such functions by showing that the top view of the family of circles is a pencil. © 2011 Springer-Verlag.

  5. Engineer Ethics

    International Nuclear Information System (INIS)

    Lee, Dae Sik; Kim, Yeong Pil; Kim, Yeong Jin

    2003-03-01

    This book tells of engineer ethics such as basic understanding of engineer ethics with history of engineering as a occupation, definition of engineering and specialized job and engineering, engineer ethics as professional ethics, general principles of ethics and its limitation, ethical theory and application, technique to solve the ethical problems, responsibility, safety and danger, information engineer ethics, biotechnological ethics like artificial insemination, life reproduction, gene therapy and environmental ethics.

  6. Integrated Advanced Microwave Sounding Unit-A (AMSU-A). Engineering Test Report: AMSU-A2 METSAT Instrument (S/N 108) Acceptance Level Vibration Tests of Dec 1999/Jan 2000 (S/O 784077, OC-454)

    Science.gov (United States)

    Heffner, R.

    2000-01-01

    This is the Engineering Test Report, AMSU-A2 METSAT Instrument (S/N 108) Acceptance Level Vibration Test of Dec 1999/Jan 2000 (S/O 784077, OC-454), for the Integrated Advanced Microwave Sounding Unit-A (AMSU-A).

  7. Food rules in the Koran

    OpenAIRE

    Kocturk, Tahire O.

    2002-01-01

    Islam is now the second largest religion in Scandinavia and has a high representation among immigrant groups. Knowledge of food rules in Islam is a necessity for nutritionists in multicultural settings. Food rules as they appear in the Koran are contained within the concepts of halal and haram. Halal means lawful, permitted and recommended by the Islamic law. Haram is the opposite, meaning unlawful, prohibited. Food rules are meant to be observed by postpubertal people in good physical and me...

  8. Atomic Energy (factories) rules: 1988

    International Nuclear Information System (INIS)

    1988-01-01

    These rules are made by the Central Government under the Factories Act, 1948 and extend to all factories engaged in carrying out the purposes of the Atomic Energy Act, 1962. The rules cover the requirements of inspecting staff, health aspects, personnel safety, personnel welfare, working hours, employment of young persons, special provisions in case of dangerous manufacturing processes or operations, supplemental rules for administrative aspects and special powers of competent authority. (M.G.B.)

  9. Optimization of conventional rule curves coupled with hedging rules for reservoir operation

    DEFF Research Database (Denmark)

    Taghian, Mehrdad; Rosbjerg, Dan; Haghighi, Ali

    2014-01-01

    As a common approach to reservoir operating policies, water levels at the end of each time interval should be kept at or above the rule curve. In this study, the policy is captured using rationing of the target yield to reduce the intensity of severe water shortages. For this purpose, a hybrid...... to achieve the optimal water allocation and the target storage levels for reservoirs. As a case study, a multipurpose, multireservoir system in southern Iran is selected. The results show that the model has good performance in extracting the optimum policy for reservoir operation under both normal...... model is developed to optimize simultaneously both the conventional rule curve and the hedging rule. In the compound model, a simple genetic algorithm is coupled with a simulation program, including an inner linear programming algorithm. In this way, operational policies are imposed by priority concepts...

  10. New method of calculating the power at altitude of aircraft engines equipped with superchargers on the basis of tests made under sea-level conditions

    Science.gov (United States)

    Sarracino, Marcello

    1941-01-01

    The present article deals with what is considered to be a simpler and more accurate method of determining, from the results of bench tests under approved rating conditions, the power at altitude of a supercharged aircraft engine, without application of correction formulas. The method of calculating the characteristics at altitude, of supercharged engines, based on the consumption of air, is a more satisfactory and accurate procedure, especially at low boost pressures.

  11. Convention on nuclear safety. Rules of procedure and financial rules

    International Nuclear Information System (INIS)

    1999-01-01

    The document is the first revision of the Rules of Procedures and Financial Rules that apply mutatis mutandis to any meetings of the Contracting Parties to the Convention on Nuclear Safety (INFCIRC/573), convened in accordance with the Chapter 3 of the Convention

  12. Convention on Nuclear Safety. Rules of procedure and financial rules

    International Nuclear Information System (INIS)

    2002-01-01

    The document is the second revision of the Rules of Procedures and Financial Rules that apply mutatis mutandis to any meetings of the Contracting Parties to the Convention on Nuclear Safety (INFCIRC/573), convened in accordance with the Chapter 3 of the Convention

  13. [Usefulness of clinical prediction rules for ruling out deep vein thrombosis in a hospital emergency department].

    Science.gov (United States)

    Rosa-Jiménez, Francisco; Rosa-Jiménez, Ascensión; Lozano-Rodríguez, Aquiles; Santoro-Martínez, María Del Carmen; Duro-López, María Del Carmen; Carreras-Álvarez de Cienfuegos, Amelia

    2015-01-01

    To compare the efficacy of the most familiar clinical prediction rules in combination with D-dimer testing to rule out a diagnosis of deep vein thrombosis (DVT) in a hospital emergency department. Retrospective cross-sectional analysis of the case records of all patients attending a hospital emergency department with suspected lower-limb DVT between 1998 and 2002. Ten clinical prediction scores were calculated and D-dimer levels were available for all patients. The gold standard was ultrasound diagnosis of DVT by an independent radiologist who was blinded to clinical records. For each prediction rule, we analyzed the effectiveness of the prediction strategy defined by "low clinical probability and negative D-dimer level" against the ultrasound diagnosis. A total of 861 case records were reviewed and 577 cases were selected; the mean (SD) age was 66.7 (14.2) years. DVT was diagnosed in 145 patients (25.1%). Only the Wells clinical prediction rule and 4 other models had a false negative rate under 2%. The Wells criteria and the score published by Johanning and colleagues identified higher percentages of cases (15.6% and 11.6%, respectively). This study shows that several clinical prediction rules can be safely used in the emergency department, although none of them have proven more effective than the Wells criteria.

  14. Rule Versus the Causality Rule in Insurance Law

    DEFF Research Database (Denmark)

    Lando, Henrik

    When the Buyer of insurance has negligently kept silent or misrepresented a (material) fact to the Seller, one of two rules will determine the extent to which cover will consequently be reduced. The pro-rata rule lowers cover in proportion to how much the Seller would have increased the premium had...... he been correctly informed; the causality rule provides either zero cover if the omitted fact has caused the insurance event, or full cover if the event would have occurred regardless of the fact. This article explores which rule is more efficient. Using the framework proposed by Picard and Dixit...... it subjects the risk averse Buyer of insurance to less variance. This implies that the pro rata rule should apply when there is significant risk for a Buyer of unintentional misrepresentation, and when the incentive to intentionally misrepresent can be curtailed through frequent verification of the Buyer...

  15. New Jersey proposes rule reducing NOx emissions

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    The New Jersey Department of Environmental Protection and Energy has proposed a rule requiring utility and industrial sources to significantly reduce their emission levels of nitrogen oxide (NO x ). If approved, it will be the first major rule mandated by the Clean Air Act Amendments of 1990 to affect New Jersey's stationary sources of these air pollutants - primarily electric generating utilities and other large fossil fuel burning facilities. The proposed rule requires all facilities with the potential to emit 25 tons or more of NO x each year to install reasonably available control technology by May 30, 1995. According to Richard Sinding, the environment and energy agency's assistant commissioner for policy and planning, the rule will likely require installation of low-NO x burners or other modifications to the combustion process. Sinding says the proposed rule will reduce the State's NO x emissions by approximately 30,000 tons a year, roughly 30 percent from current levels from these stationary sources. The pollution prevention measures are estimated to cost approximately $1,000 for each ton of NO x removed. The state energy agency estimates the average residential utility customer will see an increase in the monthly electric bill of about 50 cents. The agency said the proposed regulation includes provisions to make implementation more flexible and less costly for achieving the NO x reductions. It has approved the use of natural gas during the ozone season if low-NO x burners are not available. Additionally, emissions may be averaged from all units at the same utility or company location, effectively allowing a company to select the most cost-effective method of achieving the required emissions reductions

  16. Decree no. 2001-1199 of the 10 december 2001 publishing the resolution MSC. 88 (71) notifying adoption of the international compilation of safety rules for the spent nuclear fuels, plutonium and high level radioactive wastes transport in casks on ships (compilation INF) (annexes), adopted at London the 27 may 1999; Decret no. 2001-1199 du 10 decembre 2001 portant publication de la resolution MSC.88 (71) portant adoption du recueil international de regles de securite pour le transport de combustible nucleaire irradie, de plutonium et de dechets hautement radioactifs en colis a bord de navires (recueil INF) (ensemble une annexe), adoptee a Londres le 27 mai 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This legislative text concerns the safety rules of spent nuclear fuels, plutonium and high level radioactive wastes transport, in casks on ships. Rules, fire prevention, temperature control of casks, electric supply, radioprotection, management and emergency plans are detailed. (A.L.B.)

  17. Web Engineering

    Energy Technology Data Exchange (ETDEWEB)

    White, Bebo

    2003-06-23

    Web Engineering is the application of systematic, disciplined and quantifiable approaches to development, operation, and maintenance of Web-based applications. It is both a pro-active approach and a growing collection of theoretical and empirical research in Web application development. This paper gives an overview of Web Engineering by addressing the questions: (a) why is it needed? (b) what is its domain of operation? (c) how does it help and what should it do to improve Web application development? and (d) how should it be incorporated in education and training? The paper discusses the significant differences that exist between Web applications and conventional software, the taxonomy of Web applications, the progress made so far and the research issues and experience of creating a specialization at the master's level. The paper reaches a conclusion that Web Engineering at this stage is a moving target since Web technologies are constantly evolving, making new types of applications possible, which in turn may require innovations in how they are built, deployed and maintained.

  18. Revised Rules for Concrete Bridges

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle; Jensen, F. M.; Middleton, C.

    This paper is based on research performed for the Highway Agency, London, UK under the project DPU/9/44 "Revision of Bridge Assessment Rules Based on Whole Life Performance: Concrete Bridges" It contains details of a methodology which can be used to generate Whole Life (WL) reliability profiles....... These WL reliability profiles may be used to establish revised rules for Concrete Bridges....

  19. Business model for business rules

    NARCIS (Netherlands)

    Eline Haan; Martin Zoet; Koen Smit

    2014-01-01

    Business rule models are widely applied, standalone and embedded in smart objects. They have become segregated from information technology and they are now a valuable asset in their own right. As more business rule models are becoming assets, business models to monetize these assets are designed.

  20. Statistical Rules-of-Thumb.

    Science.gov (United States)

    Brewer, James K.

    1988-01-01

    Six best-selling introductory behavioral statistics textbooks that were published in 1982 and two well-known sampling theory textbooks were reviewed to determine the presence of rules-of-thumb--useful principles with wide application that are not intended to be strictly accurate. The relative frequency and type of rules are reported along with a…

  1. Sleep promotes the extraction of grammatical rules.

    Directory of Open Access Journals (Sweden)

    Ingrid L C Nieuwenhuis

    Full Text Available Grammar acquisition is a high level cognitive function that requires the extraction of complex rules. While it has been proposed that offline time might benefit this type of rule extraction, this remains to be tested. Here, we addressed this question using an artificial grammar learning paradigm. During a short-term memory cover task, eighty-one human participants were exposed to letter sequences generated according to an unknown artificial grammar. Following a time delay of 15 min, 12 h (wake or sleep or 24 h, participants classified novel test sequences as Grammatical or Non-Grammatical. Previous behavioral and functional neuroimaging work has shown that classification can be guided by two distinct underlying processes: (1 the holistic abstraction of the underlying grammar rules and (2 the detection of sequence chunks that appear at varying frequencies during exposure. Here, we show that classification performance improved after sleep. Moreover, this improvement was due to an enhancement of rule abstraction, while the effect of chunk frequency was unaltered by sleep. These findings suggest that sleep plays a critical role in extracting complex structure from separate but related items during integrative memory processing. Our findings stress the importance of alternating periods of learning with sleep in settings in which complex information must be acquired.

  2. Business judgement rule in Czech Corporations Act

    Directory of Open Access Journals (Sweden)

    Jaromír KOŽIAK

    2013-12-01

    Full Text Available Czech private law is currently undergoing a thorough transformation. This inclundes adoption of a brand new Corporations Act, which is to supersede the current Commercial Code. The new legislation introduces several new rules governing liability of company executive officers. One of these is business judgment rule. It should provide company executive officers with a certain level of protection against litigantion – if specific terms are met, it is presumed, that they carried out their responsibilities with proper care. I intend to demonstrate, that the czech business judgment rule is flawed, despite the fact that it draws from foreign examples and that this regulation, although seemingly groundbreaking, in fact changes nothing in examination of the decisions of the company executive officers in Czech Republic. The main goal of this article is therefore to analyze and criticize the business judgment rule in the new Czech legislation and to compare it to notable foreign legal systems. The methods used are inductive and deductive reasoning, author‘s own analysis of legal text, comparative method and compilation of available resources relating to the topic of the article.

  3. Spatio-Temporal Rule Mining

    DEFF Research Database (Denmark)

    Gidofalvi, Gyozo; Pedersen, Torben Bach

    2005-01-01

    Recent advances in communication and information technology, such as the increasing accuracy of GPS technology and the miniaturization of wireless communication devices pave the road for Location-Based Services (LBS). To achieve high quality for such services, spatio-temporal data mining techniques...... are needed. In this paper, we describe experiences with spatio-temporal rule mining in a Danish data mining company. First, a number of real world spatio-temporal data sets are described, leading to a taxonomy of spatio-temporal data. Second, the paper describes a general methodology that transforms...... the spatio-temporal rule mining task to the traditional market basket analysis task and applies it to the described data sets, enabling traditional association rule mining methods to discover spatio-temporal rules for LBS. Finally, unique issues in spatio-temporal rule mining are identified and discussed....

  4. A history of slide rules for blackbody radiation computations

    Science.gov (United States)

    Johnson, R. Barry; Stewart, Sean M.

    2012-10-01

    During the Second World War the importance of utilizing detection devices capable of operating in the infrared portion of the electromagnetic spectrum was firmly established. Up until that time, laboriously constructed tables for blackbody radiation needed to be used in calculations involving the amount of radiation radiated within a given spectral region or for other related radiometric quantities. To rapidly achieve reasonably accurate calculations of such radiometric quantities, a blackbody radiation calculator was devised in slide rule form first in Germany in 1944 and soon after in England and the United States. In the immediate decades after its introduction, the radiation slide rule was widely adopted and recognized as a useful and important tool for engineers and scientists working in the infrared field. It reached its pinnacle in the United States in 1970 in a rule introduced by Electro Optical Industries, Inc. With the onset in the latter half of the 1970s of affordable, hand-held electronic calculators, the impending demise of the radiation slide rule was evident. No longer the calculational device of choice, the radiation slide rule all but disappeared within a few short years. Although today blackbody radiation calculations can be readily accomplished using anything from a programmable pocket calculator upwards, with each device making use of a wide variety of numerical approximations to the integral of Planck's function, radiation slide rules were in the early decades of infrared technology the definitive "workhorse" for those involved in infrared systems design and engineering. This paper presents a historical development of radiation slide rules with many versions being discussed.

  5. Efficient Encoding of Inflection Rules in NLP Systems

    Directory of Open Access Journals (Sweden)

    Péter BARABÁSS

    2012-12-01

    Full Text Available The grammatical parsing unit is a core module in natural language processing engines. This unit determines the grammatical roles of the incoming words and it converts the sentences into semantic models. A special grammar rule in agglutinative languages is the inflection rule. The traditional, automata-based parsers are usually not very effective in the parsing of inflection transformations. The paper presents implementation alternatives and compares them from the viewpoint of time efficiency and accuracy. The prototype system was tested with examples from Hungarian.

  6. Checklists, rules and creativity

    Science.gov (United States)

    Glasmacher, Thomas

    2009-01-01

    Universities have something that private industry wants - a unique culture of continuous learning, curiosity-driven research and international collaboration. According to an unending string of accounts in the business press, adopting this university culture is imperative for survival and success in the "technology-driven" 21st-century economy. The industry poster child for this idea is the IT giant Google. Its success undoubtedly buys the company increasing freedom to experiment with and nurture its own unique culture. But Google is routinely lauded for fostering academic-style debate in meetings, maintaining a fluid organization chart that allows employees to try other roles, and giving its engineers one day a week to pursue their own creative ideas for advancing the company's interests.

  7. The science of structural engineering

    CERN Document Server

    Heyman, Jacques

    1999-01-01

    Structures cannot be created without engineering theory, and design rules have existed from the earliest times for building Greek temples, Roman aqueducts and Gothic cathedrals - and later, for steel skyscrapers and the frames for aircraft. This book is, however, not concerned with the description of historical feats, but with the way the structural engineer sets about his business. Galileo, in the seventeenth century, was the first to introduce recognizably modern science into the calculation of structures; he determined the breaking strength of beams. In the eighteenth century engineers move

  8. Engineering opportunities in nuclear engineering

    International Nuclear Information System (INIS)

    Walton, D.G.

    1980-01-01

    The pattern of education and training of Nuclear Engineers in the UK is outlined under the headings; degree courses for professional engineers, postgraduate courses, education of technician engineers. Universities which offer specific courses are stated and useful addresses listed. (UK)

  9. The rule of rescue.

    Science.gov (United States)

    McKie, John; Richardson, Jeff

    2003-06-01

    Jonsen coined the term "Rule of Rescue"(RR) to describe the imperative people feel to rescue identifiable individuals facing avoidable death. In this paper we attempt to draw a more detailed picture of the RR, identifying its conflict with cost-effectiveness analysis, the preference it entails for identifiable over statistical lives, the shock-horror response it elicits, the preference it entails for lifesaving over non-lifesaving measures, its extension to non-life-threatening conditions, and whether it is motivated by duty or sympathy. We also consider the measurement problems it raises, and argue that quantifying the RR would probably require a two-stage procedure. In the first stage the size of the individual utility gain from a health intervention would be assessed using a technique such as the Standard Gamble or the Time Trade-Off, and in the second the social benefits arising from the RR would be quantified employing the Person Trade-Off. We also consider the normative status of the RR. We argue that it can be defended from a utilitarian point of view, on the ground that rescues increase well-being by reinforcing people's belief that they live in a community that places great value upon life. However, utilitarianism has long been criticised for failing to take sufficient account of fairness, and the case is no different here: fairness requires that we do not discriminate between individuals on morally irrelevant grounds, whereas being "identifiable" does not seem to be a morally relevant ground for discrimination.

  10. Applicability of creep damage rules to a nickel-base heat-resistant alloy Hastelloy XR

    International Nuclear Information System (INIS)

    Tsuji, Hirokazu; Nakajima, Najime; Tanabe, Tatsuhiko; Nakasone, Yuji

    1992-01-01

    A series of constant load and temperature creep rupture tests and varying load and/or temperature creep rupture tests was carried out on a nickel-base heat-resistant alloy Hastelloy XR, which was developed for applications in the High-Temperature Engineering Test Reactor, at temperatures ranging from 850 to 1000deg C in order to examine the applicability of the conventional creep damage rules, i.e., the life fraction, the strain fraction and their mixed rules. The life fraction rule showed the best applicability of these three criteria. The good applicability of the rule was considered to result from the fact that the creep strength of Hastelloy XR was not strongly affected by the change of the chemical composition and/or the microstructure during exposure to the high-temperature simulated HTGR helium environment. In conclusion the life fraction rule is applicable in engineering design of high-temperature components made of Hastelloy XR. (orig.)

  11. Rules-based analysis with JBoss Drools: adding intelligence to automation

    International Nuclear Information System (INIS)

    Ley, E. de; Jacobs, D.

    2012-01-01

    Rule engines are specialized software systems for applying conditional actions (if/then rules) on data. They are also known as 'production rule systems'. Rules engines are less-known as software technology than the traditional procedural, object-oriented, scripting or dynamic development languages. This is a pity, as their usage may offer an important enrichment to a development toolbox. JBoss Drools is an open-source rules engine that can easily be embedded in any Java application. Through an integration in our Passerelle process automation suite, we have been able to provide advanced solutions for intelligent process automation, complex event processing, system monitoring and alarming, automated repair etc. This platform has been proven for many years as an automated diagnosis and repair engine for Belgium's largest telecom provider, and it is being piloted at Synchrotron Soleil for device monitoring and alarming. After an introduction to rules engines in general and JBoss Drools in particular, we will present its integration in a solution platform, some important principles and a practical use case. (authors)

  12. Turning Engineering Green

    DEFF Research Database (Denmark)

    Jamison, Andrew

    2012-01-01

    Since the 1970s, the relations between engineering and development have changed significantly. On the one hand, at a discursive or macro level, there has been a shift in regard to the kind of development to which engineering is meant to contribute, from furthering economic growth to an approach...... to development that is “sustainable” in one way or another. On the other hand, on a practitioner, or micro level, there has been a change in the kinds of competence that engineers are expected to have in order to be able to contribute to development, due to the emergence of new fields of “technoscience” blurring...... the boundaries between what was previously considered science and what was previously considered technology. Finally, in between, at an institutional or meso level, there have been significant changes in how engineering work and engineering education are organized. This chapter attempts to provide an overview...

  13. Aircraft engine pollution reduction.

    Science.gov (United States)

    Rudey, R. A.

    1972-01-01

    The effect of engine operation on the types and levels of the major aircraft engine pollutants is described and the major factors governing the formation of these pollutants during the burning of hydrocarbon fuel are discussed. Methods which are being explored to reduce these pollutants are discussed and their application to several experimental research programs are pointed out. Results showing significant reductions in the levels of carbon monoxide, unburned hydrocarbons, and oxides of nitrogen obtained from experimental combustion research programs are presented and discussed to point out potential application to aircraft engines. An experimental program designed to develop and demonstrate these and other advanced, low pollution combustor design methods is described. Results that have been obtained to date indicate considerable promise for reducing advanced engine exhaust pollutants to levels significantly below current engines.

  14. Cell and Tissue Engineering

    CERN Document Server

    2012-01-01

    “Cell and Tissue Engineering” introduces the principles and new approaches in cell and tissue engineering. It includes both the fundamentals and the current trends in cell and tissue engineering, in a way useful both to a novice and an expert in the field. The book is composed of 13 chapters all of which are written by the leading experts. It is organized to gradually assemble an insight in cell and tissue function starting form a molecular nano-level, extending to a cellular micro-level and finishing at the tissue macro-level. In specific, biological, physiological, biophysical, biochemical, medical, and engineering aspects are covered from the standpoint of the development of functional substitutes of biological tissues for potential clinical use. Topics in the area of cell engineering include cell membrane biophysics, structure and function of the cytoskeleton, cell-extracellular matrix interactions, and mechanotransduction. In the area of tissue engineering the focus is on the in vitro cultivation of ...

  15. Highly scalable and robust rule learner: performance evaluation and comparison.

    Science.gov (United States)

    Kurgan, Lukasz A; Cios, Krzysztof J; Dick, Scott

    2006-02-01

    Business intelligence and bioinformatics applications increasingly require the mining of datasets consisting of millions of data points, or crafting real-time enterprise-level decision support systems for large corporations and drug companies. In all cases, there needs to be an underlying data mining system, and this mining system must be highly scalable. To this end, we describe a new rule learner called DataSqueezer. The learner belongs to the family of inductive supervised rule extraction algorithms. DataSqueezer is a simple, greedy, rule builder that generates a set of production rules from labeled input data. In spite of its relative simplicity, DataSqueezer is a very effective learner. The rules generated by the algorithm are compact, comprehensible, and have accuracy comparable to rules generated by other state-of-the-art rule extraction algorithms. The main advantages of DataSqueezer are very high efficiency, and missing data resistance. DataSqueezer exhibits log-linear asymptotic complexity with the number of training examples, and it is faster than other state-of-the-art rule learners. The learner is also robust to large quantities of missing data, as verified by extensive experimental comparison with the other learners. DataSqueezer is thus well suited to modern data mining and business intelligence tasks, which commonly involve huge datasets with a large fraction of missing data.

  16. Multiple-level porous polymer monoliths with interconnected cellular topology prepared by combining hard sphere and emulsion templating for use in bone tissue engineering

    Czech Academy of Sciences Publication Activity Database

    Paljevac, M.; Gradišnik, L.; Lipovšek, S.; Maver, U.; Kotek, Jiří; Krajnc, P.

    2018-01-01

    Roč. 18, č. 2 (2018), s. 1-8, č. článku 1700306. ISSN 1616-5187 R&D Projects: GA MŠk(CZ) LO1507 Institutional support: RVO:61389013 Keywords : bone tissue engineering * hierarchical materials * polymer scaffolds Subject RIV: CD - Macromolecular Chemistry OBOR OECD: Polymer science Impact factor: 3.238, year: 2016

  17. From Student to Entry-Level Professional: Examining the Role of Language and Written Communications in the Reacculturation of Aerospace Engineering Students.

    Science.gov (United States)

    Pinelli, T. E.; And Others

    1995-01-01

    Argues that language and written communication play a critical role in the reacculturation process that enables individuals to make a successful transition from the academic world to a professional environment. Reports results of a mail survey examining the technical communications abilities of aerospace engineering students and the technical…

  18. Firm heterogeneity, Rules of Origin and Rules of Cumulation

    OpenAIRE

    Bombarda , Pamela; Gamberoni , Elisa

    2013-01-01

    We analyse the impact of relaxing rules of origin (ROOs) in a simple setting with heterogeneous firms that buy intermediate inputs from domestic and foreign sources. In particular, we consider the impact of switching from bilateral to diagonal cumulation when using preferences (instead of paying the MFN tariff) involving the respect of rules of origin. We find that relaxing the restrictiveness of the ROOs leads the least productive exporters to stop exporting. The empirical part confirms thes...

  19. Stirling engine piston ring

    Science.gov (United States)

    Howarth, Roy B.

    1983-01-01

    A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

  20. Engineering Institute

    Science.gov (United States)

    Projects Past Projects Publications NSEC » Engineering Institute Engineering Institute Multidisciplinary engineering research that integrates advanced modeling and simulations, novel sensing systems and new home of Engineering Institute Contact Institute Director Charles Farrar (505) 665-0860 Email UCSD EI

  1. Grammar Engineering Support for Precedence Rule Recovery and Compatibility Checking

    NARCIS (Netherlands)

    Bouwers, E.; Bravenboer, M.; Visser, E.

    2007-01-01

    A wide range of parser generators are used to generate parsers for programming languages. The grammar formalisms that come with parser generators provide different approaches for defining operator precedence. Some generators (e.g. YACC) support precedence declarations, others require the grammar to

  2. Rule Systems for Runtime Verification: A Short Tutorial

    Science.gov (United States)

    Barringer, Howard; Havelund, Klaus; Rydeheard, David; Groce, Alex

    In this tutorial, we introduce two rule-based systems for on and off-line trace analysis, RuleR and LogScope. RuleR is a conditional rule-based system, which has a simple and easily implemented algorithm for effective runtime verification, and into which one can compile a wide range of temporal logics and other specification formalisms used for runtime verification. Specifications can be parameterized with data, or even with specifications, allowing for temporal logic combinators to be defined. We outline a number of simple syntactic extensions of core RuleR that can lead to further conciseness of specification but still enabling easy and efficient implementation. RuleR is implemented in Java and we will demonstrate its ease of use in monitoring Java programs. LogScope is a derivation of RuleR adding a simple very user-friendly temporal logic. It was developed in Python, specifically for supporting testing of spacecraft flight software for NASA’s next 2011 Mars mission MSL (Mars Science Laboratory). The system has been applied by test engineers to analysis of log files generated by running the flight software. Detailed logging is already part of the system design approach, and hence there is no added instrumentation overhead caused by this approach. While post-mortem log analysis prevents the autonomous reaction to problems possible with traditional runtime verification, it provides a powerful tool for test automation. A new system is being developed that integrates features from both RuleR and LogScope.

  3. Mechanical engineering

    CERN Document Server

    Darbyshire, Alan

    2010-01-01

    Alan Darbyshire's best-selling text book provides five-star high quality content to a potential audience of 13,000 engineering students. It explains the most popular specialist units of the Mechanical Engineering, Manufacturing Engineering and Operations & Maintenance Engineering pathways of the new 2010 BTEC National Engineering syllabus. This challenging textbook also features contributions from specialist lecturers, ensuring that no stone is left unturned.

  4. Mixed and low-level waste treatment project: Appendix C, Health and safety criteria for the mixed and low-level waste treatment facility at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Neupauer, R.M.; Thurmond, S.M.

    1992-09-01

    This report contains health and safety information relating to the chemicals that have been identified in the mixed waste streams at the Waste Treatment Facility at the Idaho National Engineering Laboratory. Information is summarized in two summary sections--one for health considerations and one for safety considerations. Detailed health and safety information is presented in material safety data sheets (MSDSs) for each chemical

  5. Mixed and low-level waste treatment project: Appendix C, Health and safety criteria for the mixed and low-level waste treatment facility at the Idaho National Engineering Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Neupauer, R.M.; Thurmond, S.M.

    1992-09-01

    This report contains health and safety information relating to the chemicals that have been identified in the mixed waste streams at the Waste Treatment Facility at the Idaho National Engineering Laboratory. Information is summarized in two summary sections--one for health considerations and one for safety considerations. Detailed health and safety information is presented in material safety data sheets (MSDSs) for each chemical.

  6. Mixed and low-level waste treatment project: Appendix C, Health and safety criteria for the mixed and low-level waste treatment facility at the Idaho National Engineering Laboratory. Part 2, Chemical constituents

    Energy Technology Data Exchange (ETDEWEB)

    Neupauer, R.M.; Thurmond, S.M.

    1992-09-01

    This report contains health and safety information relating to the chemicals that have been identified in the mixed waste streams at the Waste Treatment Facility at the Idaho National Engineering Laboratory. Information is summarized in two summary sections--one for health considerations and one for safety considerations. Detailed health and safety information is presented in material safety data sheets (MSDSs) for each chemical.

  7. Rotary engine cooling system

    Science.gov (United States)

    Jones, Charles (Inventor); Gigon, Richard M. (Inventor); Blum, Edward J. (Inventor)

    1985-01-01

    A rotary engine has a substantially trochoidal-shaped housing cavity in which a rotor planetates. A cooling system for the engine directs coolant along a single series path consisting of series connected groups of passages. Coolant enters near the intake port, passes downwardly and axially through the cooler regions of the engine, then passes upwardly and axially through the hotter regions. By first flowing through the coolest regions, coolant pressure is reduced, thus reducing the saturation temperature of the coolant and thereby enhancing the nucleate boiling heat transfer mechanism which predominates in the high heat flux region of the engine during high power level operation.

  8. Using knowledge rules for pharmacy mapping.

    Science.gov (United States)

    Shakib, Shaun C; Che, Chengjian; Lau, Lee Min

    2006-01-01

    The 3M Health Information Systems (HIS) Healthcare Data Dictionary (HDD) is used to encode and structure patient medication data for the Electronic Health Record (EHR) of the Department of Defense's (DoD's) Armed Forces Health Longitudinal Technology Application (AHLTA). HDD Subject Matter Experts (SMEs) are responsible for initial and maintenance mapping of disparate, standalone medication master files from all 100 DoD host sites worldwide to a single concept-based vocabulary, to accomplish semantic interoperability. To achieve higher levels of automation, SMEs began defining a growing set of knowledge rules. These knowledge rules were implemented in a pharmacy mapping tool, which enhanced consistency through automation and increased mapping rate by 29%.

  9. Scoring Rules for Subjective Probability Distributions

    DEFF Research Database (Denmark)

    Harrison, Glenn W.; Martínez-Correa, Jimmy; Swarthout, J. Todd

    The theoretical literature has a rich characterization of scoring rules for eliciting the subjective beliefs that an individual has for continuous events, but under the restrictive assumption of risk neutrality. It is well known that risk aversion can dramatically affect the incentives to correctly...... report the true subjective probability of a binary event, even under Subjective Expected Utility. To address this one can “calibrate” inferences about true subjective probabilities from elicited subjective probabilities over binary events, recognizing the incentives that risk averse agents have...... to distort reports. We characterize the comparable implications of the general case of a risk averse agent when facing a popular scoring rule over continuous events, and find that these concerns do not apply with anything like the same force. For empirically plausible levels of risk aversion, one can...

  10. Quantization rules for strongly chaotic systems

    International Nuclear Information System (INIS)

    Aurich, R.; Bolte, J.

    1992-09-01

    We discuss the quantization of strongly chaotic systems and apply several quantization rules to a model system given by the unconstrained motion of a particle on a compact surface of constant negative Gaussian curvature. We study the periodic-orbit theory for distinct symmetry classes corresponding to a parity operation which is always present when such a surface has genus two. Recently, several quantization rules based on periodic orbit theory have been introduced. We compare quantizations using the dynamical zeta function Z(s) with the quantization condition cos(π N(E)) = 0, where a periodix-orbit expression for the spectral staircase N(E) is used. A general discussion of the efficiency of periodic-orbit quantization then allows us to compare the different methods. The system dependence of the efficiency, which is determined by the topological entropy τ and the mean level density anti d(E), is emphasized. (orig.)

  11. Rule Optimization monthly reservoir operation Salvajina

    International Nuclear Information System (INIS)

    Sandoval Garcia, Maria Clemencia; Santacruz Salazar, Santiago; Ramirez Callejas, Carlos A

    2007-01-01

    In the present study a model was designed for the optimization of the rule for monthly operation of the Salvajina dam (Colombia) based in the technology) of dynamic programming. The model maximizes the benefits for electric power generation, ensuring at the same time flood regulation in winter and pollution relief during the summer. For the optimization of the rule of operation, it was necessary to define the levels and volumes of reserve and holding required for the control of flood zones in the Cauca river and to provide an effluent minimal flow and assure a daily flow at the Juanchito station (located 141 km downstream from the dam) of the Cauca river, 90 % of the time during the most critical summer periods.

  12. Analyzing Strategic Business Rules through Simulation Modeling

    Science.gov (United States)

    Orta, Elena; Ruiz, Mercedes; Toro, Miguel

    Service Oriented Architecture (SOA) holds promise for business agility since it allows business process to change to meet new customer demands or market needs without causing a cascade effect of changes in the underlying IT systems. Business rules are the instrument chosen to help business and IT to collaborate. In this paper, we propose the utilization of simulation models to model and simulate strategic business rules that are then disaggregated at different levels of an SOA architecture. Our proposal is aimed to help find a good configuration for strategic business objectives and IT parameters. The paper includes a case study where a simulation model is built to help business decision-making in a context where finding a good configuration for different business parameters and performance is too complex to analyze by trial and error.

  13. A "Trans-Dyadic" Perspective on the Goldwater Rule.

    Science.gov (United States)

    Plakun, Eric M

    2017-11-01

    The Goldwater Rule has been debated, redefined, and debated further since the election of Donald Trump as President of the United States. This column offers a perspective on the Goldwater Rule that moves beyond psychiatry's current preoccupation with precision DSM-5 diagnosis of individuals, which ethically requires consent or other legal authorization for release of diagnostic information to others, and into the realm of leadership as seen through the "trans-dyadic" lens of psychoanalytic understanding of large group processes on a societal level. Concepts from large group psychology are introduced to illustrate "trans-dyadic" perspectives on leadership that do not challenge the Goldwater Rule.

  14. Decision Mining Revisited – Discovering Overlapping Rules

    NARCIS (Netherlands)

    Mannhardt, F.; de Leoni, M.; Reijers, H.A.; van der Aalst, W.M.P.

    2016-01-01

    Decision mining enriches process models with rules underlying decisions in processes using historical process execution data. Choices between multiple activities are specified through rules defined over process data. Existing decision mining methods focus on discovering mutually-exclusive rules,

  15. Decision Mining Revisited - Discovering Overlapping Rules

    NARCIS (Netherlands)

    Mannhardt, F.; De Leoni, M.; Reijers, H.A.; van der Aalst, W.M.P.; Nurcan, S.; Soffer, P.; Bajec, M.; Eder, J.

    2016-01-01

    Decision mining enriches process models with rules underlying decisions in processes using historical process execution data. Choices between multiple activities are specified through rules defined over process data. Existing decision mining methods focus on discovering mutually-exclusive rules,

  16. Decision mining revisited - Discovering overlapping rules

    NARCIS (Netherlands)

    Mannhardt, Felix; De Leoni, Massimiliano; Reijers, Hajo A.; Van Der Aalst, Wil M P

    2016-01-01

    Decision mining enriches process models with rules underlying decisions in processes using historical process execution data. Choices between multiple activities are specified through rules defined over process data. Existing decision mining methods focus on discovering mutually-exclusive rules,

  17. Exploiting endogenous CRISPR-Cas system for multiplex genome editing in Clostridium tyrobutyricum and engineer the strain for high-level butanol production.

    Science.gov (United States)

    Zhang, Jie; Zong, Wenming; Hong, Wei; Zhang, Zhong-Tian; Wang, Yi

    2018-03-09

    Although CRISPR-Cas9/Cpf1 have been employed as powerful genome engineering tools, heterologous CRISPR-Cas9/Cpf1 are often difficult to introduce into bacteria and archaea due to their severe toxicity. Since most prokaryotes harbor native CRISPR-Cas systems, genome engineering can be achieved by harnessing these endogenous immune systems. Here, we report the exploitation of Type I-B CRISPR-Cas of Clostridium tyrobutyricum for genome engineering. In silico CRISPR array analysis and plasmid interference assay revealed that TCA or TCG at the 5'-end of the protospacer was the functional protospacer adjacent motif (PAM) for CRISPR targeting. With a lactose inducible promoter for CRISPR array expression, we significantly decreased the toxicity of CRISPR-Cas and enhanced the transformation efficiency, and successfully deleted spo0A with an editing efficiency of 100%. We further evaluated effects of the spacer length on genome editing efficiency. Interestingly, spacers ≤ 20 nt led to unsuccessful transformation consistently, likely due to severe off-target effects; while a spacer of 30-38 nt is most appropriate to ensure successful transformation and high genome editing efficiency. Moreover, multiplex genome editing for the deletion of spo0A and pyrF was achieved in a single transformation, with an editing efficiency of up to 100%. Finally, with the integration of the alcohol dehydrogenase gene (adhE1 or adhE2) to replace cat1 (the key gene responsible for butyrate production and previously could not be deleted), two mutants were created for n-butanol production, with the butanol titer reached historically record high of 26.2 g/L in a batch fermentation. Altogether, our results demonstrated the easy programmability and high efficiency of endogenous CRISPR-Cas. The developed protocol herein has a broader applicability to other prokaryotes containing endogenous CRISPR-Cas systems. C. tyrobutyricum could be employed as an excellent platform to be engineered for biofuel

  18. Choice Rules and Accumulator Networks

    Science.gov (United States)

    2015-01-01

    This article presents a preference accumulation model that can be used to implement a number of different multi-attribute heuristic choice rules, including the lexicographic rule, the majority of confirming dimensions (tallying) rule and the equal weights rule. The proposed model differs from existing accumulators in terms of attribute representation: Leakage and competition, typically applied only to preference accumulation, are also assumed to be involved in processing attribute values. This allows the model to perform a range of sophisticated attribute-wise comparisons, including comparisons that compute relative rank. The ability of a preference accumulation model composed of leaky competitive networks to mimic symbolic models of heuristic choice suggests that these 2 approaches are not incompatible, and that a unitary cognitive model of preferential choice, based on insights from both these approaches, may be feasible. PMID:28670592

  19. Preschoolers can infer general rules governing fantastical events in fiction.

    Science.gov (United States)

    Van de Vondervoort, Julia W; Friedman, Ori

    2014-05-01

    Young children are frequently exposed to fantastic fiction. How do they make sense of the unrealistic and impossible events that occur in such fiction? Although children could view such events as isolated episodes, the present experiments suggest that children use such events to infer general fantasy rules. In 2 experiments, 2- to 4-year-olds were shown scenarios in which 2 animals behaved unrealistically (N = 78 in Experiment 1, N = 94 in Experiment 2). When asked to predict how other animals in the fiction would behave, children predicted novel behaviors consistent with the nature of the fiction. These findings suggest that preschoolers can infer the general rules that govern the events and entities in fantastic fiction and can use these rules to predict what events will happen in the fiction. The findings also provide evidence that children may infer fantasy rules at a more superordinate level than the basic level. (PsycINFO Database Record (c) 2014 APA, all rights reserved).

  20. The Development of a Graphical User Interface Engine for the Convenient Use of the HL7 Version 2.x Interface Engine.

    Science.gov (United States)

    Kim, Hwa Sun; Cho, Hune; Lee, In Keun

    2011-12-01

    The Health Level Seven Interface Engine (HL7 IE), developed by Kyungpook National University, has been employed in health information systems, however users without a background in programming have reported difficulties in using it. Therefore, we developed a graphical user interface (GUI) engine to make the use of the HL7 IE more convenient. The GUI engine was directly connected with the HL7 IE to handle the HL7 version 2.x messages. Furthermore, the information exchange rules (called the mapping data), represented by a conceptual graph in the GUI engine, were transformed into program objects that were made available to the HL7 IE; the mapping data were stored as binary files for reuse. The usefulness of the GUI engine was examined through information exchange tests between an HL7 version 2.x message and a health information database system. Users could easily create HL7 version 2.x messages by creating a conceptual graph through the GUI engine without requiring assistance from programmers. In addition, time could be saved when creating new information exchange rules by reusing the stored mapping data. The GUI engine was not able to incorporate information types (e.g., extensible markup language, XML) other than the HL7 version 2.x messages and the database, because it was designed exclusively for the HL7 IE protocol. However, in future work, by including additional parsers to manage XML-based information such as Continuity of Care Documents (CCD) and Continuity of Care Records (CCR), we plan to ensure that the GUI engine will be more widely accessible for the health field.

  1. 'Sum rules' for preequilibrium reactions

    International Nuclear Information System (INIS)

    Hussein, M.S.

    1981-03-01

    Evidence that suggests a correct relationship between the optical transmission matrix, P, and the several correlation widths, gamma sub(n), found in nsmission matrix, P, and the several correlation widths, n, found in multistep compound (preequilibrium) nuclear reactions, is presented. A second sum rule is also derived within the shell model approach to nuclear reactions. Indications of the potential usefulness of the sum rules in preequilibrium studies are given. (Author) [pt

  2. Cellular automata with voting rule

    International Nuclear Information System (INIS)

    Makowiec, D.

    1996-01-01

    The chosen local interaction - the voting (majority) rule applied to the square lattice is known to cause the non ergodic cellular automata behaviour. Presented computer simulation results verify two cases of non ergodicity. The first one is implicated by the noise introduced to the local interactions and the second one follows properties of the initial lattice configuration selected at random. For the simplified voting rule - non symmetric voting, the critical behaviour has been explained rigorously. (author)

  3. Practical electrical engineering

    CERN Document Server

    N Makarov, Sergey; Bitar, Stephen J

    2016-01-01

    This textbook provides comprehensive, in-depth coverage of the fundamental concepts of electrical and computer engineering. It is written from an engineering perspective, with special emphasis on circuit functionality and applications. Reliance on higher-level mathematics and physics, or theoretical proofs has been intentionally limited in order to prioritize the practical aspects of electrical engineering. This text is therefore suitable for a number of introductory circuit courses for other majors such as robotics, mechanical, biomedical, aerospace, civil, architecture, petroleum, and industrial engineering. The authors’ primary goal is to teach the aspiring engineering student all fundamental tools needed to understand, analyze and design a wide range of practical circuits and systems. Their secondary goal is to provide a comprehensive reference, for both major and non-major students as well as practicing engineers. Provides a self-contained, fundamental textbook on electric circuits and basic electronic...

  4. Introduction to biomedical engineering

    CERN Document Server

    Enderle, John D; Blanchard, Susan M

    2005-01-01

    Under the direction of John Enderle, Susan Blanchard and Joe Bronzino, leaders in the field have contributed chapters on the most relevant subjects for biomedical engineering students. These chapters coincide with courses offered in all biomedical engineering programs so that it can be used at different levels for a variety of courses of this evolving field. Introduction to Biomedical Engineering, Second Edition provides a historical perspective of the major developments in the biomedical field. Also contained within are the fundamental principles underlying biomedical engineering design, analysis, and modeling procedures. The numerous examples, drill problems and exercises are used to reinforce concepts and develop problem-solving skills making this book an invaluable tool for all biomedical students and engineers. New to this edition: Computational Biology, Medical Imaging, Genomics and Bioinformatics. * 60% update from first edition to reflect the developing field of biomedical engineering * New chapters o...

  5. Sum rules in classical scattering

    International Nuclear Information System (INIS)

    Bolle, D.; Osborn, T.A.

    1981-01-01

    This paper derives sum rules associated with the classical scattering of two particles. These sum rules are the analogs of Levinson's theorem in quantum mechanics which provides a relationship between the number of bound-state wavefunctions and the energy integral of the time delay of the scattering process. The associated classical relation is an identity involving classical time delay and an integral over the classical bound-state density. We show that equalities between the Nth-order energy moment of the classical time delay and the Nth-order energy moment of the classical bound-state density hold in both a local and a global form. Local sum rules involve the time delay defined on a finite but otherwise arbitrary coordinate space volume S and the bound-state density associated with this same region. Global sum rules are those that obtain when S is the whole coordinate space. Both the local and global sum rules are derived for potentials of arbitrary shape and for scattering in any space dimension. Finally the set of classical sum rules, together with the known quantum mechanical analogs, are shown to provide a unified method of obtaining the high-temperature expansion of the classical, respectively the quantum-mechanical, virial coefficients

  6. Using the Chain Rule as the Key Link in Deriving the General Rules for Differentiation

    Science.gov (United States)

    Sprows, David

    2011-01-01

    The standard approach to the general rules for differentiation is to first derive the power, product, and quotient rules and then derive the chain rule. In this short article we give an approach to these rules which uses the chain rule as the main tool in deriving the power, product, and quotient rules in a manner which is more student-friendly…

  7. A unix configuration engine

    International Nuclear Information System (INIS)

    Burgess, M.

    1994-06-01

    A high level description language is presented for the purpose of automatically configuring large heterogeneous networked unix environments, based on class-oriented abstractions. The configuration engine is portable and easily extensible

  8. Delta Learning Rule for the Active Sites Model

    OpenAIRE

    Lingashetty, Krishna Chaithanya

    2010-01-01

    This paper reports the results on methods of comparing the memory retrieval capacity of the Hebbian neural network which implements the B-Matrix approach, by using the Widrow-Hoff rule of learning. We then, extend the recently proposed Active Sites model by developing a delta rule to increase memory capacity. Also, this paper extends the binary neural network to a multi-level (non-binary) neural network.

  9. State of R and D of radioactive waste disposal (5). R and D of low level radioactive waste disposal. Engineered barrier: evaluation of barrier materials

    International Nuclear Information System (INIS)

    Hironaga, Michihiko

    2008-01-01

    The Central Research Institute of Electric Power Industry (CRIEPI) has researched and developed the long-term durability evaluation of engineered barrier materials for the facility of sub-surface disposal at intermediate depth. The important functions of engineered barrier are mechanical stability of construction, low hydraulic conductivity and diffusivity, and absorption of nuclide. A natural barrier plays an important part in nuclide transfer. Some examples of researches on the engineered barrier with cement and bentonite are reported. They contained the leaching test of hardened cement paste using X-ray microanalysis, relation between the dissociation rate of montmorillonite and pH from 15 to 70 deg C, and the mechanism of gas permeability of dense bentonite. The results of leaching test showed that the modified underground water leached smaller amount of ions than the ion exchanged water. The sediment was found on the surface of hardened paste. The dissociation rate of smectite under alkaline conditions showed almost the same values as neutral conditions at 15 deg C. (S.Y.)

  10. The main requirements for research work against the challenges of "Industry - 4.0" and the analysis of ongoing work in improving the state of the material and technical base and improving the level of training of young engineers

    Directory of Open Access Journals (Sweden)

    Р. С. Турманидзе

    2017-12-01

    Full Text Available The work analyzes theoretical and practical results obtained after each of the first three world scientific - technical revolution, appreciated their role in the development of humanity, and improve the level of industry in different sectors of the economy. More discussed in detail situation on the threshold of the fourth scientific - technical revolution "industry-4". It is proved crucial in accelerating these processes, the level of training of young engineering staff and suggestions, some ideas and solutions to these problems on the example of the Georgian Technical University.

  11. Game engines: a survey

    Directory of Open Access Journals (Sweden)

    A. Andrade

    2015-11-01

    Full Text Available Due to hardware limitations at the origin of the video game industry, each new game was generally coded from the ground up. Years later, from the evolution of hardware and the need for quick game development cycles, spawned the concept of game engine. A game engine is a reusable software layer allowing the separation of common game concepts from the game assets (levels, graphics, etc.. This paper surveys fourteen different game engines relevant today, ranging from the industry-level to the newcomer-friendlier ones.

  12. Systems engineering management plan

    International Nuclear Information System (INIS)

    Conner, C.W.

    1985-10-01

    The purpose of this Systems Engineering Management Plan (SEMP) is to prescribe the systems engineering procedures to be implemented at the Program level and the minimum requirements for systems engineering at the Program-element level. The Program level corresponds to the Director, OCRWM, or to the organizations within OCRWM to which the Director delegates responsibility for the development of the System and for coordinating and integrating the activities at the Program-element level. The Office of Policy and Outreach (OPO) and the Office of Resource Management (ORM) support the Director at the Program level. The Program-element level corresponds to the organizations within OCRWM (i.e., the Office of Geologic Repositories (OGR) and the Office of Storage and Transportation Systems (OSTS)) with overall responsibility for developing the System elements - that is, the mined geologic disposal system (MGDS), monitored retrievable storage (MRS) (if approved by Congress), and the transportation system

  13. Kids rules the internet

    DEFF Research Database (Denmark)

    Sørensen, Birgitte Holm

    2006-01-01

    ?Power users? are children who explore the cutting edge of new media and develop their competencies at a level where few adults can follow. Adults concerns over children?s and adolescents? activities on the Internet can often be ascribed to the fact that the children master the new media faster...... than their parents and their teachers. Adults who take the time to familiarise themselves with common practice on the Internet will usually abandon their concerns in favour of a more positive and supportive attitude....

  14. Experimental Technique of Titanium Fire in Aero-engine

    Directory of Open Access Journals (Sweden)

    MI Guangbao

    2016-06-01

    Full Text Available Titanium fire is the typical catastrophic fault in the aero-engine. Aiming at the urgent demand for experimental technique of titanium fire from advanced high thrust-weight ratio aero-engine, the combustion technology and theory of titanium alloy based on friction oxygen concentration method (FOC were systematically studied. The evaluation method of fireproof property and the friction ignition model were built, and the fireproof mechanism was illustrated. By generalizing recent progress in experimental technique of titanium fire from three levels, including evolutionary rule, mechanism and prevention and control technology, the ideas and directions of experimental technique associated with the application research of titanium fire in the future were proposed, namely overall evaluation of fireproof property close to air flow environment of the aero-engine, prediction model of fireproof property and experimental verification of fireproof technique under the air flow environment of aero-engine. It is necessary to establish the prevention system of titanium fire in aero-engine, which contributes to the realization of "full titanium" in compressor and to the increase of high thrust-weight ratio.

  15. Business Rules Definition for Decision Support System Using Matrix Grammar

    Directory of Open Access Journals (Sweden)

    Eva Zámečníková

    2016-06-01

    Full Text Available This paper deals with formalization of business rules by formal grammars. In our work we focus on methods for high frequency data processing. We process data by using complex event platforms (CEP which allow to process high volume of data in nearly real time. Decision making process is contained by one level of processing of CEP. Business rules are used for decision making process description. For the business rules formalization we chose matrix grammar. The use of formal grammars is quite natural as the structure of rules and its rewriting is very similar both for the business rules and for formal grammar. In addition the matrix grammar allows to simulate dependencies and correlations between the rules. The result of this work is a model for data processing of knowledge-based decision support system described by the rules of formal grammar. This system will support the decision making in CEP. This solution may contribute to the speedup of decision making process in complex event processing and also to the formal verification of these systems.

  16. Engineering Cartilage

    Science.gov (United States)

    ... Research Matters NIH Research Matters March 3, 2014 Engineering Cartilage Artistic rendering of human stem cells on ... situations has been a major goal in tissue engineering. Cartilage contains water, collagen, proteoglycans, and chondrocytes. Collagens ...

  17. Governing Engineering

    DEFF Research Database (Denmark)

    Buch, Anders

    2012-01-01

    Most people agree that our world face daunting problems and, correctly or not, technological solutions are seen as an integral part of an overall solution. But what exactly are the problems and how does the engineering ‘mind set’ frame these problems? This chapter sets out to unravel dominant...... perspectives in challenge per-ception in engineering in the US and Denmark. Challenge perception and response strategies are closely linked through discursive practices. Challenge perceptions within the engineering community and the surrounding society are thus critical for the shaping of engineering education...... and the engineering profession. Through an analysis of influential reports and position papers on engineering and engineering education the chapter sets out to identify how engineering is problematized and eventually governed. Drawing on insights from governmentality studies the chapter strives to elicit the bodies...

  18. Industrial Engineering

    DEFF Research Database (Denmark)

    Karlsson, Christer

    2015-01-01

    Industrial engineering is a discipline that is concerned with increasing the effectiveness of (primarily) manufacturing and (occasionally).......Industrial engineering is a discipline that is concerned with increasing the effectiveness of (primarily) manufacturing and (occasionally)....

  19. Governing Engineering

    DEFF Research Database (Denmark)

    Buch, Anders

    2011-01-01

    Abstract: Most people agree that our world faces daunting problems and, correctly or not, technological solutions are seen as an integral part of an overall solution. But what exactly are the problems and how does the engineering ‘mind set’ frame these problems? This chapter sets out to unravel...... dominant perspectives in challenge perception in engineering in the US and Denmark. Challenge perception and response strategies are closely linked through discursive practices. Challenge perceptions within the engineering community and the surrounding society are thus critical for the shaping...... of engineering education and the engineering profession. Through an analysis of influential reports and position papers on engineering and engineering education the chapter sets out to identify how engineering is problematized and eventually governed. Drawing on insights from governmentality studies the chapter...

  20. Computer Engineers.

    Science.gov (United States)

    Moncarz, Roger

    2000-01-01

    Looks at computer engineers and describes their job, employment outlook, earnings, and training and qualifications. Provides a list of resources related to computer engineering careers and the computer industry. (JOW)

  1. Engineering _ litteraturliste

    DEFF Research Database (Denmark)

    Sillasen, Martin Krabbe; Daugbjerg, Peer; Nielsen, Keld

    2017-01-01

    Litteraturliste udarbejdet som grundlag for artiklen ”Engineering – svaret på naturfagenes udfordringer?”......Litteraturliste udarbejdet som grundlag for artiklen ”Engineering – svaret på naturfagenes udfordringer?”...

  2. Space civil engineering - A new discipline

    Science.gov (United States)

    Sadeh, Willy Z.; Criswell, Marvin E.

    1991-01-01

    Space Civil Engineering is an emerging engineering discipline that focuses on extending and expanding the Civil Engineering know-how and practice to the development and maintenance of infrastructure on celestial bodies. Space Civil Engineering is presently being developed as a new discipline within the Department of Civil Engineering at Colorado State University under a recently established NASA Space Grant College Program. Academic programs geared toward creating Space Civil Engineering Options at both undergraduate and graduate levels are being formulated. Basic ideas and concepts of the curriculum in the Space Civil Engineering Option at both undergraduate and graduate levels are presented. The role of Space Civil Engineering in the Space Program is discussed.

  3. Ageing in civil engineering materials and structures

    Energy Technology Data Exchange (ETDEWEB)

    Jaeger, Jean-Marc [SETEC TPI, Tour Gamma D 58, quai de la Rapee, 75583 Paris (France)

    2005-07-01

    SETEC TPI will address the 'Aging' topic of the Dijon Symposium by talking about: aging in civil engineering materials and structures, prevention of aging phenomena, in-operation monitoring of degradations related to aging and compensatory measures required to maintain a good safety level. Works as the Millau viaduct, the EdF skyscraper at La Defense - Paris, the renovation of the Grand Palais of Paris and special structures with Monaco's floating dam as well as the 'number 10' shaped gateway boat at Marseilles are illustrations for the issues discussed. The durability of civil engineering structures has become a major concern for designers. The Millau viaduct is designed for a service life of 120 years, and the Monaco dam for 100 years. Calculation rules have been evolving toward the incorporation of the concept of life cycle, for example, the Eurocodes 2 rules (reinforced concrete). The talk will expose the factors which are being taken into account to delay aging versus structure types. This part will be focused towards materials and corresponding regulations: - Reinforced concrete (coating of reinforcements, opening of cracks, choice of reinforcement types), BAEL and Eurocodes 2 rules; - Frame steel (protection, sacrificial anode), CM66 and Eurocodes 3 rules. New materials will also be mentioned: - Ultra high-performance fiber/concrete, with the example of CERACEM applied at Millau for the covering of the toll area barrier; - Titanium, which is starting to appear in the building trades, as for instance for the Beijing China Opera House shell. The second part of the talk will be devoted to a specific case namely, the 'number 10' shaped gateway bridge, a prestressed concrete structure immersed in the Port of Marseilles, which will be used to illustrate the aging phenomenon in a corrosive environment. We will focus on the types of inspection series performed by the Autonomous Port Authority of Marseilles to check the behavior of

  4. NASA Systems Engineering Handbook

    Science.gov (United States)

    Hirshorn, Steven R.; Voss, Linda D.; Bromley, Linda K.

    2017-01-01

    The update of this handbook continues the methodology of the previous revision: a top-down compatibility with higher level Agency policy and a bottom-up infusion of guidance from the NASA practitioners in the field. This approach provides the opportunity to obtain best practices from across NASA and bridge the information to the established NASA systems engineering processes and to communicate principles of good practice as well as alternative approaches rather than specify a particular way to accomplish a task. The result embodied in this handbook is a top-level implementation approach on the practice of systems engineering unique to NASA. Material used for updating this handbook has been drawn from many sources, including NPRs, Center systems engineering handbooks and processes, other Agency best practices, and external systems engineering textbooks and guides. This handbook consists of six chapters: (1) an introduction, (2) a systems engineering fundamentals discussion, (3) the NASA program project life cycles, (4) systems engineering processes to get from a concept to a design, (5) systems engineering processes to get from a design to a final product, and (6) crosscutting management processes in systems engineering. The chapters are supplemented by appendices that provide outlines, examples, and further information to illustrate topics in the chapters. The handbook makes extensive use of boxes and figures to define, refine, illustrate, and extend concepts in the chapters.

  5. Exploring the Effectiveness of Interdisciplinary Instruction on Learning: A Case Study in a College Level Course on Culture, Aid, and Engineering

    Directory of Open Access Journals (Sweden)

    Timothy Frank

    2013-04-01

    Full Text Available The opportunity for higher education students to study a topic through multiple, integrated angles is rare even though life outside of the classroom is filled with problems that require blending of knowledge areas to make appropriate decisions. The authors created a course at the United States Air Force Academy called Foreign Area Studies (FAS 495 in the Spring 2012 semester that integrated African studies, economics, history, political science, literature, project management, military strategy, language, culture, and environmental engineering in the study of how foreign aid has affected Mozambique and how an engineering technology along with cultural consciousness can be effectively used for good. To determine effectiveness of the interdisciplinary approach, qualitative data from student reflection papers and in-class discussions were collected and analyzed. The intent of this paper is to highlight the challenges and lessons learned from developing a project based interdisciplinary course. Results suggest a project based course with interdisciplinary pedagogy can be effective in meeting course goals and increasing meaningful student learning.

  6. Code of Ethics for Electrical Engineers

    Science.gov (United States)

    Matsuki, Junya

    The Institute of Electrical Engineers of Japan (IEEJ) has established the rules of practice for its members recently, based on its code of ethics enacted in 1998. In this paper, first, the characteristics of the IEEJ 1998 ethical code are explained in detail compared to the other ethical codes for other fields of engineering. Secondly, the contents which shall be included in the modern code of ethics for electrical engineers are discussed. Thirdly, the newly-established rules of practice and the modified code of ethics are presented. Finally, results of questionnaires on the new ethical code and rules which were answered on May 23, 2007, by 51 electrical and electronic students of the University of Fukui are shown.

  7. A Belief Rule-Based Expert System to Assess Bronchiolitis Suspicion from Signs and Symptoms Under Uncertainty

    DEFF Research Database (Denmark)

    Karim, Rezuan; Hossain, Mohammad Shahadat; Khalid, Md. Saifuddin

    2017-01-01

    developed generic belief rule-based inference methodology by using evidential reasoning (RIMER) acts as the inference engine of this BRBES while belief rule base as the knowledge representation schema. The knowledge base of the system is constructed by using real patient data and expert opinion from...

  8. 75 FR 51934 - Telemarketing Sales Rule

    Science.gov (United States)

    2010-08-24

    ... FEDERAL TRADE COMMISSION 16 CFR Part 310 Telemarketing Sales Rule AGENCY: Federal Trade Commission. ACTION: Final rule; correction. SUMMARY: The Federal Trade Commission (``Commission'') published a final rule on August 10, 2010, adopting amendments to the Telemarketing Sales Rule that address the...

  9. Noise Optimization in Diesel Engines

    Directory of Open Access Journals (Sweden)

    S. Narayan

    2014-04-01

    Full Text Available Euro 6 norms emphasize on reduction of emissions from the engines. New injection methods are being adopted for homogenous mixture formation in diesel engines. During steady state conditions homogenous combustion gave noise levels in lower frequencies. In this work noise produced in a 440 cc diesel engine has been investigated. The engine was run under various operating conditions varying various injection parameters.

  10. Liquid Rocket Engine Testing Overview

    Science.gov (United States)

    Rahman, Shamim

    2005-01-01

    Contents include the following: Objectives and motivation for testing. Technology, Research and Development Test and Evaluation (RDT&E), evolutionary. Representative Liquid Rocket Engine (LRE) test compaigns. Apollo, shuttle, Expandable Launch Vehicles (ELV) propulsion. Overview of test facilities for liquid rocket engines. Boost, upper stage (sea-level and altitude). Statistics (historical) of Liquid Rocket Engine Testing. LOX/LH, LOX/RP, other development. Test project enablers: engineering tools, operations, processes, infrastructure.

  11. Integration rules for scattering equations

    International Nuclear Information System (INIS)

    Baadsgaard, Christian; Bjerrum-Bohr, N.E.J.; Bourjaily, Jacob L.; Damgaard, Poul H.

    2015-01-01

    As described by Cachazo, He and Yuan, scattering amplitudes in many quantum field theories can be represented as integrals that are fully localized on solutions to the so-called scattering equations. Because the number of solutions to the scattering equations grows quite rapidly, the contour of integration involves contributions from many isolated components. In this paper, we provide a simple, combinatorial rule that immediately provides the result of integration against the scattering equation constraints for any Möbius-invariant integrand involving only simple poles. These rules have a simple diagrammatic interpretation that makes the evaluation of any such integrand immediate. Finally, we explain how these rules are related to the computation of amplitudes in the field theory limit of string theory.

  12. Fuzzy rule-based model for hydropower reservoirs operation

    Energy Technology Data Exchange (ETDEWEB)

    Moeini, R.; Afshar, A.; Afshar, M.H. [School of Civil Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of)

    2011-02-15

    Real-time hydropower reservoir operation is a continuous decision-making process of determining the water level of a reservoir or the volume of water released from it. The hydropower operation is usually based on operating policies and rules defined and decided upon in strategic planning. This paper presents a fuzzy rule-based model for the operation of hydropower reservoirs. The proposed fuzzy rule-based model presents a set of suitable operating rules for release from the reservoir based on ideal or target storage levels. The model operates on an 'if-then' principle, in which the 'if' is a vector of fuzzy premises and the 'then' is a vector of fuzzy consequences. In this paper, reservoir storage, inflow, and period are used as premises and the release as the consequence. The steps involved in the development of the model include, construction of membership functions for the inflow, storage and the release, formulation of fuzzy rules, implication, aggregation and defuzzification. The required knowledge bases for the formulation of the fuzzy rules is obtained form a stochastic dynamic programming (SDP) model with a steady state policy. The proposed model is applied to the hydropower operation of ''Dez'' reservoir in Iran and the results are presented and compared with those of the SDP model. The results indicate the ability of the method to solve hydropower reservoir operation problems. (author)

  13. Atypical Rulings of the Indonesian Constitutional Court

    Directory of Open Access Journals (Sweden)

    Bisariyadi

    2016-08-01

    Full Text Available In deciding judicial review cases, the Court may issue rulings that is not in accordance to what is stipulated in the Constitutional Court Law (Law Number 8 Year 2011. Atypical rulings means that the court may reconstruct a provision, delay the legislation/rulings enactment or give instruction to lawmakers. In addition, the court also introduce the “conditionally (unconstitutional” concept. This essay attempts to identify and classify these atypical rulings, including conditionally (un constitutional rulings, by examined the constitutional court judicial review rulings from 2003 to 2015. This study will provide a ground work for advance research on typical rulings by the Indonesian constitutional court.

  14. Five Rules for the Evolution of Cooperation

    Science.gov (United States)

    Nowak, Martin A.

    2006-12-01

    Cooperation is needed for evolution to construct new levels of organization. Genomes, cells, multicellular organisms, social insects, and human society are all based on cooperation. Cooperation means that selfish replicators forgo some of their reproductive potential to help one another. But natural selection implies competition and therefore opposes cooperation unless a specific mechanism is at work. Here I discuss five mechanisms for the evolution of cooperation: kin selection, direct reciprocity, indirect reciprocity, network reciprocity, and group selection. For each mechanism, a simple rule is derived that specifies whether natural selection can lead to cooperation.

  15. Gaming the system. Dodging the rules, ruling the dodgers.

    Science.gov (United States)

    Morreim, E H

    1991-03-01

    Although traditional obligations of fidelity require physicians to deliver quality care to their patients, including to utilize costly technologies, physicians are steadily losing their accustomed control over the necessary resources. The "economic agents" who own the medical and monetary resources of care now impose a wide array of rules and restrictions in order to contain their costs of operation. However, physicians can still control resources indirectly through "gaming the system," employing tactics such as "fudging" that exploit resource rules' ambiguity and flexibility to bypass the rules while ostensibly honoring them. Physicians may be especially inclined to game the system where resource rules seriously underserve patients' needs, where economic agents seem to be "gaming the patient," with needless obstacles to care, or where others, such as hospitals or even physicians themselves, may be denied needed reimbursements. Though tempting, gaming is morally and medically hazardous. It can harm patients and society, offend honesty, and violate basic principles of contractual and distributive justice. It is also, in fact, usually unnecessary in securing needed resources for patients. More fundamentally, we must reconsider what physicians owe their patients. They owe what is theirs to give: their competence, care and loyalty. In light of medicine's changing economics, two new duties emerge: economic advising, whereby physicians explicitly discuss the economic as well as medical aspects of each treatment option; and economic advocacy, whereby physicians intercede actively on their patients' behalf with the economic agents who control the resources.

  16. Methodological approaches based on business rules

    Directory of Open Access Journals (Sweden)

    Anca Ioana ANDREESCU

    2008-01-01

    Full Text Available Business rules and business processes are essential artifacts in defining the requirements of a software system. Business processes capture business behavior, while rules connect processes and thus control processes and business behavior. Traditionally, rules are scattered inside application code. This approach makes it very difficult to change rules and shorten the life cycle of the software system. Because rules change more quickly than the application itself, it is desirable to externalize the rules and move them outside the application. This paper analyzes and evaluates three well-known business rules approaches. It also outlines some critical factors that have to be taken into account in the decision to introduce business rules facilities in a software system. Based on the concept of explicit manipulation of business rules in a software system, the need for a general approach based on business rules is discussed.

  17. Computational engineering

    CERN Document Server

    2014-01-01

    The book presents state-of-the-art works in computational engineering. Focus is on mathematical modeling, numerical simulation, experimental validation and visualization in engineering sciences. In particular, the following topics are presented: constitutive models and their implementation into finite element codes, numerical models in nonlinear elasto-dynamics including seismic excitations, multiphase models in structural engineering and multiscale models of materials systems, sensitivity and reliability analysis of engineering structures, the application of scientific computing in urban water management and hydraulic engineering, and the application of genetic algorithms for the registration of laser scanner point clouds.

  18. "Genetic Engineering" Gains Momentum (Science/Society Case Study).

    Science.gov (United States)

    Moore, John W.; Moore, Elizabeth A., Eds.

    1980-01-01

    Reviews the benefits and hazards of genetic engineering, or "recombinant-DNA" research. Recent federal safety rules issued by NIH which ease the strict prohibitions on recombinant-DNA research are explained. (CS)

  19. Architectural Engineers

    DEFF Research Database (Denmark)

    Petersen, Rikke Premer

    engineering is addresses from two perspectives – as an educational response and an occupational constellation. Architecture and engineering are two of the traditional design professions and they frequently meet in the occupational setting, but at educational institutions they remain largely estranged....... The paper builds on a multi-sited study of an architectural engineering program at the Technical University of Denmark and an architectural engineering team within an international engineering consultancy based on Denmark. They are both responding to new tendencies within the building industry where...... the role of engineers and architects increasingly overlap during the design process, but their approaches reflect different perceptions of the consequences. The paper discusses some of the challenges that design education, not only within engineering, is facing today: young designers must be equipped...

  20. Tissue engineering

    CERN Document Server

    Fisher, John P; Bronzino, Joseph D

    2007-01-01

    Increasingly viewed as the future of medicine, the field of tissue engineering is still in its infancy. As evidenced in both the scientific and popular press, there exists considerable excitement surrounding the strategy of regenerative medicine. To achieve its highest potential, a series of technological advances must be made. Putting the numerous breakthroughs made in this field into a broad context, Tissue Engineering disseminates current thinking on the development of engineered tissues. Divided into three sections, the book covers the fundamentals of tissue engineering, enabling technologies, and tissue engineering applications. It examines the properties of stem cells, primary cells, growth factors, and extracellular matrix as well as their impact on the development of tissue engineered devices. Contributions focus on those strategies typically incorporated into tissue engineered devices or utilized in their development, including scaffolds, nanocomposites, bioreactors, drug delivery systems, and gene t...

  1. Methodological approaches based on business rules

    OpenAIRE

    Anca Ioana ANDREESCU; Adina UTA

    2008-01-01

    Business rules and business processes are essential artifacts in defining the requirements of a software system. Business processes capture business behavior, while rules connect processes and thus control processes and business behavior. Traditionally, rules are scattered inside application code. This approach makes it very difficult to change rules and shorten the life cycle of the software system. Because rules change more quickly than the application itself, it is desirable to externalize...

  2. Evolving temporal association rules with genetic algorithms

    OpenAIRE

    Matthews, Stephen G.; Gongora, Mario A.; Hopgood, Adrian A.

    2010-01-01

    A novel framework for mining temporal association rules by discovering itemsets with a genetic algorithm is introduced. Metaheuristics have been applied to association rule mining, we show the efficacy of extending this to another variant - temporal association rule mining. Our framework is an enhancement to existing temporal association rule mining methods as it employs a genetic algorithm to simultaneously search the rule space and temporal space. A methodology for validating the ability of...

  3. Rules Extraction with an Immune Algorithm

    Directory of Open Access Journals (Sweden)

    Deqin Yan

    2007-12-01

    Full Text Available In this paper, a method of extracting rules with immune algorithms from information systems is proposed. Designing an immune algorithm is based on a sharing mechanism to extract rules. The principle of sharing and competing resources in the sharing mechanism is consistent with the relationship of sharing and rivalry among rules. In order to extract rules efficiently, a new concept of flexible confidence and rule measurement is introduced. Experiments demonstrate that the proposed method is effective.

  4. Architecture of Environmental Engineering

    DEFF Research Database (Denmark)

    Wenzel, Henrik; Alting, Leo

    2006-01-01

    An architecture of Environmental Engineering has been developed comprising the various disciplines and tools involved. It identifies industry as the major actor and target group, and it builds on the concept of Eco-efficiency. To improve Eco-efficiency, there is a limited number of intervention......-efficiency is the aim of Environmental Engineering, the discipline of synthesis – design and creation of solutions – will form a core pillar of the architecture. Other disciplines of Environmental Engineering exist forming the necessary background and frame for the synthesis. Environmental Engineering, thus, in essence...... comprise the disciplines of: management, system description & inventory, analysis & assessment, prioritisation, synthesis, and communication, each existing at all levels of intervention. The developed architecture of Environmental Engineering, thus, consists of thirty individual disciplines, within each...

  5. Architecture of Environmental Engineering

    DEFF Research Database (Denmark)

    Wenzel, Henrik; Alting, Leo

    2004-01-01

    An architecture of Environmental Engineering has been developed comprising the various disciplines and tools involved. It identifies industry as the major actor and target group, and it builds on the concept of Eco-efficiency. To improve Eco-efficiency, there is a limited number of intervention...... of Eco-efficiency is the aim of Environmental Engineering, the discipline of synthesis – design and creation of solutions – will form a core pillar of the architecture. Other disciplines of Environmental Engineering exist forming the necessary background and frame for the synthesis. Environmental...... Engineering, thus, in essence comprise the disciplines of: management, system description & inventory, analysis & assessment, prioritisation, synthesis, and communication, each existing at all levels of intervention. The developed architecture of Environmental Engineering, thus, consists of thirty individual...

  6. Professional ethics in biomedical engineering practice and research.

    Science.gov (United States)

    Monzon, Jorge E; Monzon-Wyngaard, Alvaro

    2008-01-01

    This paper discusses some guidelines for use with the accepted fundamental canons of ethics for engineers. We present some rules of practice and professional obligations emerging from these canons. Basic recommendations for engineers dissenting on ethical grounds are also presented. Ethical issues relating to Biomedical Engineering research are illustrated. We mention some cases that could be used to further understanding the ethical implications of biomedical engineering practice.

  7. A Comparative Analysis of Fuzzy Inference Engines in Context of ...

    African Journals Online (AJOL)

    PROF. O. E. OSUAGWU

    Fuzzy Inference engine is an important part of reasoning systems capable of extracting correct conclusions from ... is known as the inference, or rule definition portion, of fuzzy .... minimal set of decision rules based on input- ... The study uses Mamdani FIS model and. Sugeno FIS ... control of induction motor drive. [18] study.

  8. Who rules the roost?

    Science.gov (United States)

    Zuckerman, Barry; Sanoff, Margot Kaplan; Augustyn, Marilyn

    2010-01-01

    Adam's mother was concerned about her 3-year-old son's hyperactivity, violence, and activity level. Adam and his mom had recently moved into a shelter for pregnant women. The rest of the residents are primarily in their early 20s, whereas Adam's mom is 42. She had found about 3 months ago that she was pregnant. This was her fourth pregnancy, second with this father, and he had recently left her when she refused an abortion. Her other children are 22 and 24 and live out of state. She has a history of opioid addiction. She had been on methadone during Adam's gestation and had recently started on buprenorphine to treat her addiction during this pregnancy as well. Adam is here today for his 3-year-old checkup and you had not seen him for a year. Mom states that he has been healthy but has become progressively active over the last year. He is very angry about his dad leaving, and according to Adam's mother "blames her" for sending him away. They are living in 1 room at the shelter, and mom is finding it increasingly difficult to keep him busy all day. When she goes out looking for a job, he is very challenging at the shelter, and she constantly receives complaints that he is "too loud" in the common rooms. She feels like she is at the end of her rope with him, he is constantly climbing, bolting from her, and taking risks.When you examine Adam, you find a robust, healthy young boy. His eye contact is good, and he is socially related but does actively explore your office. When he begins taking the instruments off your wall, his mother sits passively watching him. When he begins playing with the faucet, she half heartedly tells him to "stop" but he looks at her and continues splashing. He then begins flicking the light switch on and off in the room with no response from mom. When you ask about discipline, mom states "nothing works." When you ask about supports, she states "I have nobody except Adam and the new baby now."Adam was born after an uneventful full-term pregnancy

  9. NASA/DOD Aerospace Knowledge Diffusion Research Project. Paper 50: From student to entry-level professional: Examining the role of language and written communications in the reacculturation of aerospace engineering students

    Science.gov (United States)

    Pinelli, Thomas E.; Barclay, Rebecca O.; Keene, Michael L.; Kennedy, John M.; Hecht, Laura F.

    1995-01-01

    When students graduate and enter the world of work, they must make the transition from an academic to a professional knowledge community. Kenneth Bruffee's model of the social construction of knowledge suggests that language and written communication play a critical role in the reacculturation process that enables successful movement from one knowledge community to another. We present the results of a national (mail) survey that examined the technical communications abilities, skills, and competencies of 1,673 aerospace engineering students, who represent an academic knowledge community. These results are examined within the context of the technical communications behaviors and practices reported by 2,355 aerospace engineers and scientists employed in government and industry, who represent a professional knowledge community that the students expect to join. Bruffee's claim of the importance of language and written communication in the successful transition from an academic to a professional knowledge community is supported by the responses from the two communities we surveyed. Implications are offered for facilitating the reacculturation process of students to entry-level engineering professionals.

  10. Bisphenol A; Final Test Rule

    Science.gov (United States)

    EPA is issuing a final rule, under section 4 of the Toxic Substances Control Act (TSCA) requiring manufacturers and processors of bisphenol A, hereinafter BPA, (4.4’-isopropylidenediphenol, CAS No. 80-05—7) to conduct a 90-day inhalation study.

  11. Polarizability sum rules in QED

    International Nuclear Information System (INIS)

    Llanta, E.; Tarrach, R.

    1978-01-01

    The well founded total photoproduction and the, assumed subtraction free, longitudinal photoproduction polarizability sum rules are checked in QED at the lowest non-trivial order. The first one is shown to hold, whereas the second one turns out to need a subtraction, which makes its usefulness for determining the electromagnetic polarizabilities of the nucleons quite doubtful. (Auth.)

  12. Rules and Acts of Considerateness

    Czech Academy of Sciences Publication Activity Database

    Beran, Ondřej

    2015-01-01

    Roč. 22, č. 3 (2015), s. 395-418 ISSN 1370-0049 R&D Projects: GA ČR(CZ) GA13-20785S Institutional support: RVO:67985955 Keywords : normativity, moral rules * Wittgensteinian ethics * particularity Subject RIV: AA - Philosophy ; Religion Impact factor: 0.250, year: 2015

  13. Phase space quark counting rule

    International Nuclear Information System (INIS)

    Wei-gin, C.; Lo, S.

    1980-01-01

    A simple quark counting rule based on phase space consideration suggested before is used to fit all 39 recent experimental data points on inclusive reactions. Parameter free relations are found to agree with experiments. Excellent detail fits are obtained for 11 inclusive reactions

  14. Selection rules for splitting strings

    NARCIS (Netherlands)

    Achucarro, A; Gregory, R

    1997-01-01

    It has been pointed out that Nielsen-Olesen vortices may be able to decay by pair production of black holes. We show that when the Abelian-Higgs model is embedded in a larger theory, the additional fields mau lead to selection rules for this process-even in the absence of fermions-due to the failure

  15. Cosmic-ray sum rules

    International Nuclear Information System (INIS)

    Frandsen, Mads T.; Masina, Isabella; Sannino, Francesco

    2011-01-01

    We introduce new sum rules allowing to determine universal properties of the unknown component of the cosmic rays; we show how they can be used to predict the positron fraction at energies not yet explored by current experiments, and to constrain specific models.

  16. New Economy - New Policy Rules?

    NARCIS (Netherlands)

    Bullard, J.; Schaling, E.

    2000-01-01

    The U.S. economy appears to have experienced a pronounced shift toward higher productivity over the last five years or so. We wish to understand the implications of such shifts for the structure of optimal monetary policy rules in simple dynamic economies. Accordingly, we begin with a standard

  17. Rule-based Information Integration

    NARCIS (Netherlands)

    de Keijzer, Ander; van Keulen, Maurice

    2005-01-01

    In this report, we show the process of information integration. We specifically discuss the language used for integration. We show that integration consists of two phases, the schema mapping phase and the data integration phase. We formally define transformation rules, conversion, evolution and

  18. Following the Rules of Discourse

    Czech Academy of Sciences Publication Activity Database

    Peregrin, Jaroslav

    2010-01-01

    Roč. 2, č. 1 (2010), s. 118-128 ISSN 1877-3095 R&D Projects: GA ČR(CZ) GA401/07/0904 Institutional research plan: CEZ:AV0Z90090514 Keywords : rule * normativity * speech acts * evolution Subject RIV: AA - Philosophy ; Religion

  19. Neutrino mass sum-rule

    Science.gov (United States)

    Damanik, Asan

    2018-03-01

    Neutrino mass sum-rele is a very important research subject from theoretical side because neutrino oscillation experiment only gave us two squared-mass differences and three mixing angles. We review neutrino mass sum-rule in literature that have been reported by many authors and discuss its phenomenological implications.

  20. Design of a Fuzzy Rule Base Expert System to Predict and Classify ...

    African Journals Online (AJOL)

    The main objective of design of a rule base expert system using fuzzy logic approach is to predict and forecast the risk level of cardiac patients to avoid sudden death. In this proposed system, uncertainty is captured using rule base and classification using fuzzy c-means clustering is discussed to overcome the risk level, ...