DATA QUALIFICATION REPORT: WATER-LEVEL DATA FROM THE NYE COUNTY EARLY WARNING DRILLING PROGRAM

International Nuclear Information System (INIS)

F. H. Dove, P. Sanchez, and L. Saraka

2000-01-01

The objective of this work is to evaluate unqualified, water-level data gathered under the Nye County Early Warning Drilling Program (EWDP) and to determine whether the status of the data should be changed to ''qualified'' data in accordance with AP-SIII.2Q (Qualification of Unqualified Data and the Documentation of Rationale for Accepted Data). The corroboration method (as defined in Attachment 2 of AP-SIII.2Q) was implemented to qualify water-level data from Nye County measurements obtained directly from the Nye County Nuclear Waste Repository Program Office (NWRPO). Comparison of United States Geological Survey (USGS) measurements contained in DTN GS990608312312.003 with the Nye County water-level data has shown that the differences in water-level altitudes for the same wells are significantly less than 1 meter. This is an acceptable finding. Evaluation and recommendation criteria have been strictly applied to qualify Nye County measurements of water levels in selected wells measured by the USGS. However, the process of qualifying measured results by corroboration also builds confidence that the Nye County method for measurement of water levels is adequate for the intended use of the data (which is regional modeling). Therefore, it is reasonable to extend the term of ''qualified'' to water-level measurements in the remaining Nye County Phase I wells on the basis that the method has been shown to produce adequate results for the intended purpose of supporting large-scale modeling activities for the Yucca Mountain Project (YMP). The Data Qualification Team recommends the Nye County, water-level data contained in Appendix D of this report be designated as ''qualified''. These data document manual measurements of water-levels in eight (8) EWDP Phase I drillholes that were obtained prior to the field installation of continuous monitoring equipment

Measuring the quality of child health care at first-level facilities.

Science.gov (United States)

Gouws, Eleanor; Bryce, Jennifer; Pariyo, George; Armstrong Schellenberg, Joanna; Amaral, João; Habicht, Jean-Pierre

2005-08-01

Sound policy and program decisions require timely information based on valid and relevant measures. Recent findings suggest that despite the availability of effective and affordable guidelines for the management of sick children in first-level health facilities in developing countries, the quality and coverage of these services remains low. We report on the development and evaluation of a set of summary indices reflecting the quality of care received by sick children in first-level facilities. The indices were first developed through a consultative process to achieve face validity by involving technical experts and policymakers. The definition of evaluation measures for many public health programs stops at this point. We added a second phase in which standard statistical techniques were used to evaluate the content and construct validity of the indices and their reliability, drawing on data sets from the multi-country evaluation of integrated management of childhood illness (MCE) in Brazil, Tanzania and Uganda. The statistical evaluation identified important conceptual errors in the indices arising from the theory-driven expert review. The experts had combined items into inappropriate indicators resulting in summary indices that were difficult to interpret and had limited validity for program decision making. We propose a revised set of summary indices for the measurement of child health care in developing countries that is supported by both expert and statistical reviews and that led to similar programmatic insights across the three countries. We advocate increased cross-disciplinary research within public health to improve measurement approaches. Child survival policymakers, program planners and implementers can use these tools to improve their monitoring and so increase the health impact of investments in health facility care.

The revised program for measurements in intense operation mode according to AVV-IMIS

International Nuclear Information System (INIS)

Bieringer, J.; Wirth, E.; Buehling, A.; Mueller-Neumann, M.; Haase, G.; Heinrich, T.; Steinkopff, T.; Wiezorek, C.

2007-01-01

The monitoring program for measurements in intense operation mode has been revised recently by a working group at the Federal Ministry for Environment, Nature Conservation and Reactor Safety (BMU). The major issues of the revision are reported in this contribution. Measurements in intense operation must be appropriate for fast assessment of the radiological situation, for estimating the dose to the population and for decisions on countermeasures to minimize the dose. In order to meet these requirements the structure of the measurement program in intense operation mode was divided into three phases when different exposition paths are relevant: before and during dispersion of radioactive material, immediately after dispersion of radioactive material has ended and a late phase when contamination values have decreased in different environmental media. For each of these phases a special measurement program was defined that is tailored to achieve the above mentioned objectives. Minimum detectable activity concentrations were introduced similar to the measurement program in routine operation mode. They follow the intervention levels in the catalogue of countermeasures and maximum permitted values given by the European Union (EU) for food and animal feed. The minimum detectable activity concentrations were defined such that the detection of 1/10 of the intervention levels for countermeasures is ensured. (orig.)

Program of critical experiment and measurements at the RA reactor; Program kriticnih eksperimenata i merenja na reaktoru RA

Energy Technology Data Exchange (ETDEWEB)

NONE

1960-04-14

Program described in this document describes in detail the following experiments: critical experiments with two reactor core lattices with 38 and 44 fuel channels, initial heavy water level being 1300 mm, criticality is achieved by adding heavy water; preliminary analysis of heavy water quality and verification of the fuel isotopic contents; experiment with the initial core which contains 56 fuel channels with maximum heavy water level according to the Russian proposal; measurement of neutron flux by Dy and In foils; measurement of reactivity excess dependent on the heavy water level and number of fuel rods; measurement of reactor period for determined reactivity change; measurement of moderator temperature coefficient; measurement of absolute flux. [Serbo-Croat] Program sadrzan u ovom dokumentu opisuje detaljno sledece eksperimente: kriticni eksperiment sa dve konfiguracije jezgra reaktora, sa 38 i 44 gorivna kanala, pocetni nivo teske vode je 1300 mm, kriticnost se dostize dodavanjem teske vode; prethodno izvrsenom analizom teske vode i proverom izotopskog sastava goriva; eksperiment sa pocetnom resetkom koja prema ruskom predlogu sadrzi 56 gorivnih kanala i maksimalnom visinom teske vode; merenje raspodele neutronskog fluksa folijama Dy i In; kalibracija regulacionih sipki; merenje viska reaktivnosti sa promenom visine nivoa teske vode i promenom broja sipki; merenje periode reaktora za odredjenu promenu reaktivnosti; merenje temperaturnog koeficijenta za vodu; merenje apsolutnog fluksa.

Low-level Radioactivity Measurements

International Nuclear Information System (INIS)

Churtgen, C.

2007-01-01

The low-level radioactivity measurements service performs measurements of alpha or beta emitters on various types of low-radioactivity samples (biological and environmental) from internal and external clients. to maintain and develop techniques concerning the measurement of low-level radioactivity of alpha and beta emitting radionuclides in environmental or biological samples; to measure these samples by means of low-background counters (liquid scintillators, proportional counters, ZnS counters and alpha-spectrometers); to support and advise the nuclear and non-nuclear industry on problems of radioactive contamination or low level radioactivity measurements; to maintain the quality assurance system according to the ISO17025 standard for which we obtained the Beltest accreditation in 1998; to assess the internal dose from occupational intakes of radionuclides for workers of the nuclear industry;

Low-level Radioactivity Measurements

International Nuclear Information System (INIS)

Hurtgen, C.

2002-01-01

The objectives of the research performed in the area of low-level radioactivity measurements are (1) to maintain and develop techniques for the measurement of low-level environmental and biological samples, (2) to measure these samples by means of low-background counters (liquid scintillators, proportional counters, ZnS counters, alpha spectrometry), (3) to support and advise the nuclear and non-nuclear industry on problems of radioactive contamination and low-level radioactivity measurements; (4) to maintain and improve the quality assurance system according to the ISO17025 standard; and (5) to assess the internal dose from occupational intakes of radionuclides of workers of the nuclear industry. Progress and achievements in these areas in 2001 are reported

Low-level Radioactivity Measurements

International Nuclear Information System (INIS)

Hurtgen, C.

2001-01-01

The objectives of the research performed in the area of low-level radioactivity measurements are (1) to maintain and develop techniques for the measurement of low-level environmental and biological samples, (2) to measure these samples by means of low-background counters (liquid scintillators, proportional counters, ZnS counters, alpha spectrometry), (3) to support and advice the nuclear and non-nuclear industry in matters concerning radioactive contamination and/or low-level radioactivity measurements; (4) to maintain the quality assurance system according to the EN45001/ISO17025 standard; and (5) to assess the internal dose from occupational intakes of radionuclides of workers of the nuclear industry. Progress and achievements in these areas in 2000 are reported

THE PROGRAM-TARGET PLANNING AND MANAGEMENT OF DEVELOPMENT OF MEASURING EQUIPMENT PARK

Directory of Open Access Journals (Sweden)

Marichev Pavel Aleksandrovich

2018-02-01

Full Text Available Subject: study of the Park of Measuring Equipment (PME that includes hundreds of thousands of standard samples, measuring instruments, control and measuring devices and other measuring mechanisms with different areas of application, levels of reliability, service life, levels of technical perfection and levels of technical condition. Research objectives: 1. Development of a complex of mathematical models to simulate the processes of development of PME, control indicators of PME performance as a whole, purposefully control the stages of life cycle of measuring equipment samples. 2. Development of the method which, with a sufficient degree of validity and objectivity, would solve the tasks of management of procurement and repairs both in preparation of proposals for preliminary long-term plan documents (LTPD and to ensure control over the implementation of adopted plans. Thus, the method being developed should be fairly simple to use, easily adjustable for solving problems of different dimensions, suitable for solving the optimal control problem for PME as a whole, for a part of PME, and also suitable for solving a generalized problem for certain “aggregated objects” such as the Metrology Centers. Materials and methods: the methods of mathematical simulation, methods of comparative analysis, simplex method for solving linear programming problem, methods of program-target planning were used. Results: an approach to the solution of problems of program-target planning based on solving a series of linear programming problems has been developed. The results have been presented of using the approach both for formulation of proposals into the preliminary LTPD and also for introducing revisions (amendments to annual plans, which are implemented in the framework of the state defense order. Conclusions: the described method and algorithms constitute an effective tool for solving practical problems of target-oriented management of PME performance

Potential transportation demand management programs and measures

Energy Technology Data Exchange (ETDEWEB)

Litman, T. [Victoria Transport Policy Institute, Victoria, BC (Canada)

1997-02-07

The advantages of transportation demand management (TDM) programs were discussed. TDM includes several policies, programs and measures designed to change travel patterns. TDM programs include commute trip reductions, pricing policies, land use management strategies, and programs to support alternative modes of transportation such as public transit, carpooling, bicycling, walking and telecommuting. TDM programs are designed to reduce traffic congestion and air pollution. Some other TDM programs and measures include: enabling programs, alternative mode encouragement, driving disincentives, parking programs, marginalizing user costs, reducing automobile ownership, and land use management.

Radon Measurement Proficiency (RMP) Program methods and devices

International Nuclear Information System (INIS)

Harrison, J.; Hoornbeek, J.; Jalbert, P.; Sensintaffar, E.; Hopper, R.

1991-01-01

The US EPA developed the voluntary Radon Measurement Proficiency Program in 1986 in response to a Federal and State need for measurement services firms to demonstrate their proficiency with radon measurement methods and devices. Since that time, the program has set basic standards for the radon measurement industry. The program has grown dramatically since its inception. In 1986, fewer than 50 companies participated in the program. By 1989, more than 5,000 companies were participating. Participants represent firms with an analytical capability as well as firms that rely upon another firm for analysis service. Since the beginning of the RMP Program, the Agency has learned a great deal about radon measurement methods and devices. This paper reviews the measurement devices used in the program and what the EPA has learned about them since the program's inception. Performance data from the RMP Program are used to highlight relevant findings

Auditing measurement control programs

International Nuclear Information System (INIS)

Roberts, F.P.; Brouns, R.J.

1979-10-01

Requirements and a general procedure for auditing measurement control programs used in special nuclear material accounting are discussed. The areas of measurement control that need to be examined are discussed and a suggested checklist is included to assist in the preparation and performance of the audit

Future directions of defense programs high-level waste technology programs

International Nuclear Information System (INIS)

Chee, T.C.; Shupe, M.W.; Turner, D.A.; Campbell, M.H.

1987-01-01

The Department of Energy has been managing high-level waste from the production of nuclear materials for defense activities over the last forty years. An objective for the Defense Waste and Transportation Management program is to develop technology which ensures the safe, permanent disposal of all defense radioactive wastes. Technology programs are underway to address the long-term strategy for permanent disposal of high-level waste generated at each Department of Energy site. Technology is being developed for assessing the hazards, environmental impacts, and costs of each long-term disposal alternative for selection and implementation. This paper addresses key technology development areas, and consideration of recent regulatory requirements associated with the long-term management of defense radioactive high-level waste

Preferred listening levels of mobile phone programs when considering subway interior noise

Directory of Open Access Journals (Sweden)

Jyaehyoung Yu

2016-01-01

Full Text Available Today, people listen to music loud using personal listening devices. Although a majority of studies have reported that the high volume played on these listening devices produces a latent risk of hearing problems, there is a lack of studies on "double noise exposures" such as environmental noise plus recreational noise. The present study measures the preferred listening levels of a mobile phone program with subway interior noise for 74 normal-hearing participants in five age groups (ranging from 20s to 60s. The speakers presented the subway interior noise at 73.45 dB, while each subject listened to three application programs [Digital Multimedia Broadcasting (DMB, music, game] for 30 min using a tablet personal computer with an earphone. The participants′ earphone volume levels were analyzed using a sound level meter and a 2cc coupler. Overall, the results showed that those in their 20s listened to the three programs significantly louder with DMB set at significantly higher volume levels than for the other programs. Higher volume levels were needed for middle frequency compared to the lower and higher frequencies. We concluded that any potential risk of noise-induced hearing loss for mobile phone users should be communicated when users listen regularly, although the volume level was not high enough that the users felt uncomfortable. When considering individual listening habits on mobile phones, further study to predict total accumulated environmental noise is still needed.

Preferred listening levels of mobile phone programs when considering subway interior noise.

Science.gov (United States)

Yu, Jyaehyoung; Lee, Donguk; Han, Woojae

2016-01-01

Today, people listen to music loud using personal listening devices. Although a majority of studies have reported that the high volume played on these listening devices produces a latent risk of hearing problems, there is a lack of studies on "double noise exposures" such as environmental noise plus recreational noise. The present study measures the preferred listening levels of a mobile phone program with subway interior noise for 74 normal-hearing participants in five age groups (ranging from 20s to 60s). The speakers presented the subway interior noise at 73.45 dB, while each subject listened to three application programs [Digital Multimedia Broadcasting (DMB), music, game] for 30 min using a tablet personal computer with an earphone. The participants' earphone volume levels were analyzed using a sound level meter and a 2cc coupler. Overall, the results showed that those in their 20s listened to the three programs significantly louder with DMB set at significantly higher volume levels than for the other programs. Higher volume levels were needed for middle frequency compared to the lower and higher frequencies. We concluded that any potential risk of noise-induced hearing loss for mobile phone users should be communicated when users listen regularly, although the volume level was not high enough that the users felt uncomfortable. When considering individual listening habits on mobile phones, further study to predict total accumulated environmental noise is still needed.

Marr's levels and the minimalist program.

Science.gov (United States)

Johnson, Mark

2017-02-01

A simple change to a cognitive system at Marr's computational level may entail complex changes at the other levels of description of the system. The implementational level complexity of a change, rather than its computational level complexity, may be more closely related to the plausibility of a discrete evolutionary event causing that change. Thus the formal complexity of a change at the computational level may not be a good guide to the plausibility of an evolutionary event introducing that change. For example, while the Minimalist Program's Merge is a simple formal operation (Berwick & Chomsky, 2016), the computational mechanisms required to implement the language it generates (e.g., to parse the language) may be considerably more complex. This has implications for the theory of grammar: theories of grammar which involve several kinds of syntactic operations may be no less evolutionarily plausible than a theory of grammar that involves only one. A deeper understanding of human language at the algorithmic and implementational levels could strengthen Minimalist Program's account of the evolution of language.

Overview: Defense high-level waste technology program

International Nuclear Information System (INIS)

Shupe, M.W.; Turner, D.A.

1987-01-01

Defense high-level waste generated by atomic energy defense activities is stored on an interim basis at three U.S. Department of Energy (DOE) operating locations; the Savannah River Plant in South Carolina, the Hanford Site in Washington, and the Idaho National Engineering Laboratory in Idaho. Responsibility for the permanent disposal of this waste resides with DOE's Office of Defense Waste and Transportation Management. The objective of the Defense High-Level Wast Technology Program is to develop the technology for ending interim storage and achieving permanent disposal of all U.S. defense high-level waste. New and readily retrievable high-level waste are immobilized for disposal in a geologic repository. Other high-level waste will be stabilized in-place if, after completion of the National Environmental Policy Act (NEPA) process, it is determined, on a site-specific basis, that this option is safe, cost effective and environmentally sound. The immediate program focus is on implementing the waste disposal strategy selected in compliance with the NEPA process at Savannah River, while continuing progress toward development of final waste disposal strategies at Hanford and Idaho. This paper presents an overview of the technology development program which supports these waste management activities and an assessment of the impact that recent and anticipated legal and institutional developments are expected to have on the program

Understanding low-level radioactive waste. National Low-Level Radioactive Waste Management Program

International Nuclear Information System (INIS)

1983-10-01

Chapters are devoted to: background and policymaking for low-level waste management; commercial low-level waste generation; Department of Energy low-level waste generation; low-level waste treatment; packaging and transportation; commercial low-level waste disposal; Department of Energy low-level waste disposal; Department of Energy low-level waste management program; and laws and regulations

Liquid level measurement in high level nuclear waste slurries

International Nuclear Information System (INIS)

Weeks, G.E.; Heckendorn, F.M.; Postles, R.L.

1990-01-01

Accurate liquid level measurement has been a difficult problem to solve for the Defense Waste Processing Facility (DWPF). The nuclear waste sludge tends to plug or degrade most commercially available liquid-level measurement sensors. A liquid-level measurement system that meets demanding accuracy requirements for the DWPF has been developed. The system uses a pneumatic 1:1 pressure repeater as a sensor and a computerized error correction system. 2 figs

Nuclear systems of level measurement

International Nuclear Information System (INIS)

Lara, A.J.; Cabrera, M.J.

1992-01-01

In the industry there are processes in which is necessary to maintain the products level controlled which are handled for their transformation. The majority of such processes and by the operation conditions, they do not admit measure systems of level of invasive type then the application of nuclear techniques for level measurement results a big aid in these cases, since all the system installation is situated beyond frontiers of vessels that contain the product for measuring. In the Department of Nuclear Technology Applications of Mexican Petroleum Institute was developed a level measurement system by gamma rays transmission which operates in the Low Density Polyethylene plant of Petrochemical Complex Escolin at Poza Rica, Veracruz, Mexico. (Author)

Advancing nursing leadership: a model for program implementation and measurement.

Science.gov (United States)

Omoike, Osei; Stratton, Karen M; Brooks, Beth A; Ohlson, Susan; Storfjell, Judy Lloyd

2011-01-01

Despite the abundant literature documenting the need for nurse management education and career development, only recently have professional standards been targeted for this group. Competency standards for nurse leaders repeatedly identify systems-level concepts including finance and budget, communication skills, strategic management, human resources management, change management, and computer technology skills. However, educational initiatives to meet these standards are still at the early stages and most nurse leaders continue to acquire knowledge and experience through "on-the-job" training. This article will illustrate the need for partnerships and collaboration between academia and hospitals to advance nursing leadership to the next century. In addition, a tool to measure the impact of a graduate certificate program in nursing administration on nurse leader competencies is presented. Overall, the certificate program has been successful in multiple ways; it has "graduated" almost 80 nurse leaders, improved participant competence in their role at the systems level, as well as providing an impetus for completion of a graduate degree post program.

High-level waste immobilization program: an overview

International Nuclear Information System (INIS)

Bonner, W.R.

1979-09-01

The High-Level Waste Immobilization Program is providing technology to allow safe, affordable immobilization and disposal of nuclear waste. Waste forms and processes are being developed on a schedule consistent with national needs for immobilization of high-level wastes stored at Savannah River, Hanford, Idaho National Engineering Laboratory, and West Valley, New York. This technology is directly applicable to high-level wastes from potential reprocessing of spent nuclear fuel. The program is removing one more obstacle previously seen as a potential restriction on the use and further development of nuclear power, and is thus meeting a critical technological need within the national objective of energy independence

Measurement uncertainty in broadband radiofrequency radiation level measurements

Directory of Open Access Journals (Sweden)

Vulević Branislav D.

2014-01-01

Full Text Available For the evaluation of measurement uncertainty in the measurement of broadband radio frequency radiation, in this paper we propose a new approach based on the experience of the authors of the paper with measurements of radiofrequency electric field levels conducted in residential areas of Belgrade and over 35 municipalities in Serbia. The main objective of the paper is to present practical solutions in the evaluation of broadband measurement uncertainty for the in-situ RF radiation levels. [Projekat Ministarstva nauke Republike Srbije, br. III43009

Multi-level programming paradigm for extreme computing

International Nuclear Information System (INIS)

Petiton, S.; Sato, M.; Emad, N.; Calvin, C.; Tsuji, M.; Dandouna, M.

2013-01-01

In order to propose a framework and programming paradigms for post peta-scale computing, on the road to exa-scale computing and beyond, we introduced new languages, associated with a hierarchical multi-level programming paradigm, allowing scientific end-users and developers to program highly hierarchical architectures designed for extreme computing. In this paper, we explain the interest of such hierarchical multi-level programming paradigm for extreme computing and its well adaptation to several large computational science applications, such as for linear algebra solvers used for reactor core physic. We describe the YML language and framework allowing describing graphs of parallel components, which may be developed using PGAS-like language such as XMP, scheduled and computed on supercomputers. Then, we propose experimentations on supercomputers (such as the 'K' and 'Hooper' ones) of the hybrid method MERAM (Multiple Explicitly Restarted Arnoldi Method) as a case study for iterative methods manipulating sparse matrices, and the block Gauss-Jordan method as a case study for direct method manipulating dense matrices. We conclude proposing evolutions for this programming paradigm. (authors)

From mission to measures: performance measure development for a Teen Pregnancy Prevention Program.

Science.gov (United States)

Farb, Amy Feldman; Burrus, Barri; Wallace, Ina F; Wilson, Ellen K; Peele, John E

2014-03-01

The Office of Adolescent Health (OAH) sought to create a comprehensive set of performance measures to capture the performance of the Teen Pregnancy Prevention (TPP) program. This performance measurement system needed to provide measures that could be used internally (by both OAH and the TPP grantees) for management and program improvement as well as externally to communicate the program's progress to other interested stakeholders and Congress. This article describes the selected measures and outlines the considerations behind the TPP measurement development process. Issues faced, challenges encountered, and lessons learned have broad applicability for other federal agencies and, specifically, for TPP programs interested in assessing their own performance and progress. Published by Elsevier Inc.

State-Level Reforms That Support College-Level Program Changes in North Carolina

Science.gov (United States)

Bowling, R. Edward; Morrissey, Sharon; Fouts, George M.

2014-01-01

This chapter describes the concurrent reforms occurring in North Carolina--both campus-level changes focused on such issues as developing structured programs of study and state-level reforms aimed at supporting the campus efforts.

Objectively Measured Physical Activity Levels among Ethnic Minority Children Attending School-Based Afterschool Programs in a High-Poverty Neighborhood

Directory of Open Access Journals (Sweden)

Youngdeok Kim, Marc Lochbaum

2017-09-01

Full Text Available Ethnic minority children living in high poverty neighborhoods are at high risk of having insufficient physical activity (PA during school days and, thus, the importance of school as a place to facilitate PA in these underserved children has been largely emphasized. This study examined the levels and patterns of PA in minority children, with particular focus on the relative contributions of regular physical education (PE and school-based afterschool PA program in promoting moderate- and vigorous-intensity PA (MVPA during school days. PA data were repeatedly measured using a Polar Active accelerometer across multiple school days (M = 5.3 days per child, from seventy-five ethnic minority children attending a Title I public elementary school in a high-poverty neighborhood in the US. The minutes and percentage of MVPA accumulated during school, PE, and afterschool PA program were compared to the current recommendations (≥30-min of MVPA during school hours; and ≥50% of MVPA during PE or afterschool PA program as well as by the demographic characteristics including sex, grade, ethnicity, and weight status using a general linear mixed model that accounts for repeated observations. On average, children spent 41.6 mins (SE = 1.8 of MVPA during school hours and of those, 14.1 mins (SE = 0.6 were contributed during PE. The average proportion of time spent in MVPA during PE was 31.3% (SE = 1.3, which was significantly lower than the recommendation (≥50% of MVPA, whereas 54.2% (SE = 1.2 of time in afterschool PA program were spent in MVPA. The percentage of monitoring days meeting current recommendations were 69.5% (SE = 0.03, 20.8% (SE = 0.02, and 59.6% (SE = 0.03 for during school, PE, and afterschool PA program, respectively. Our findings highlighted that school-based afterschool PA, in addition to regular PE classes, could be of great benefit to promote PA in minority children during school days. Further research and practice are still needed to

Measurement control program for nuclear material accounting

International Nuclear Information System (INIS)

Brouns, R.J.; Roberts, F.P.; Merrill, J.A.; Brown, W.B.

1980-06-01

A measurement control program for nuclear material accounting monitors and controls the quality of the measurments of special nuclear material that are involved in material balances. The quality is monitored by collecting data from which the current precision and accuracy of measurements can be evaluated. The quality is controlled by evaluations, reviews, and other administrative measures for control of selection or design of facilities, equipment and measurement methods and the training and qualification of personnel who perform SNM measurements. This report describes the most important elements of a program by which management can monitor and control measurement quality

Measurement and verification of low income energy efficiency programs in Brazil: Methodological challenges

Energy Technology Data Exchange (ETDEWEB)

Martino Jannuzzi, Gilberto De; Rodrigues da Silva, Ana Lucia; Melo, Conrado Augustus de; Paccola, Jose Angelo; Dourado Maia Gomes, Rodolfo (State Univ. of Campinas, International Energy Initiative (Brazil))

2009-07-01

Electric utilities in Brazil are investing about 80 million dollars annually in low-income energy efficiency programs, about half of their total compulsory investments in end-use efficiency programs under current regulation. Since 2007 the regulator has enforced the need to provide evaluation plans for the programs delivered. This paper presents the measurement and verification (MandV) methodology that has been developed to accommodate the characteristics of lighting and refrigerator programs that have been introduced in the Brazilian urban and peri-urban slums. A combination of household surveys, end-use measurements and metering at the transformers and grid levels were performed before and after the program implementation. The methodology has to accommodate the dynamics, housing, electrical wiring and connections of the population as well as their ability to pay for the electricity and program participation. Results obtained in slums in Rio de Janeiro are presented. Impacts of the programs were evaluated in energy terms to households and utilities. Feedback from the evaluations performed also permitted the improvement in the design of new programs for low-income households.

Liquid metal level measurement

International Nuclear Information System (INIS)

Hale, J.C.; Leyland, K.S.

1982-01-01

A liquid metal level indicator is described which can be used to measure, in a stainless steel tank, the level of a nuclear reactor coolant such as sodium. The instrument, which is based on the eddy current induction effect, gives readings over substantially the full depth of the tank and indicates the sense of change of level. (U.K.)

State background-radiation levels: results of measurements taken during 1975-1979

International Nuclear Information System (INIS)

Myrick, T.E.; Berven, B.A.; Haywood, F.F.

1981-11-01

Background radiation levels across the United States have been measured by the Off-Site Pollutant Measurements Group of the Health and Safety Research Division at Oak Ridge National Laboratory (ORNL). These measurements have been conducted as part of the ORNL program of radiological surveillance at inactive uranium mills and sites formerly utilized during Manhattan Engineer District and early Atomic Energy Commission projects. The measurements included determination of 226 Ra, 232 Th, and 238 U concentrations in surface soil samples and measurement of external gamma-ray exposure rates at 1 m above the ground surface at the location of soil sampling. This information is being utilized for comparative purposes to determine the extent of contamination present at the survey sites and surrounding off-site areas. The sampling program to date has provided background information at 356 locations in 33 states. External gamma-ray exposure rates were found to range from less than 1 to 34 μR/h, with an US average of 8.5 μR/h. The nationwide average concentrations of 226 Ra, 232 Th, and 238 U in surface soil were determined to be 1.1, 0.98, and 1.0 pCi/g, respectively

Measurement of liquid level in a natural circulation circuit using an ultrasonic technique

International Nuclear Information System (INIS)

Barbosa, Amanda Cardozo; Su, Jian

2017-01-01

The measurement by an ultrasonic technique of the water level in the expansion tank of the Natural Circulation Circuit (NCC) of the Experimental Thermo-Hydraulic Laboratory of the Institute of Nuclear Engineering is presented. In the single-phase NCC operation the water level in the expansion tank is stable. However, during the two-phase operation, oscillations occur in the water level due to temperature and vacuum fraction variations. Thus, the development of a technique that allows the measurement of these oscillations, will allow an estimation of the variation of the vacuum fraction of the circuit over time. The experimental set - up was performed on a test bench, using an ultrasonic transducer. The ultrasonic technique used is pulse-echo, in which the same transducer is the transmitter and receiver of the signal. The transducer-shoe assembly is part of an ultrasonic system consisting of an ultrasonic signal generating plate, transducers and a computer (PC) with a program in LabView to control the system. The program is able to calculate the transit time that the ultrasonic signals take to cross the tank base wall, the layer (level) of liquid and return to the transducer. Knowing the speed of the ultrasound in the wall and in the liquid it is possible to calculate the thickness of the wall and the height of the liquid. Measurements were made by filling the tank with a known volume of water and under varying temperature conditions, from room temperature to 90 deg C. The liquid heights are determined and the volume of water calculated by measuring the temperature with a digital thermometer. The volumes measured were highly accurate when compared to the known volumes

A model for a national low level waste program

International Nuclear Information System (INIS)

Blankenhorn, James A.

2009-01-01

A national program for the management of low level waste is essential to the success of environmental clean-up, decontamination and decommissioning, current operations and future missions. The value of a national program is recognized through procedural consistency and a shared set of resources. A national program requires a clear waste definition and an understanding of waste characteristics matched against available and proposed disposal options. A national program requires the development and implementation of standards and procedures for implementing the waste hierarchy, with a specitic emphasis on waste avoidance, minimization and recycling. It requires a common set of objectives for waste characterization based on the disposal facility's waste acceptance criteria, regulatory and license requirements and performance assessments. Finally, a national waste certification program is required to ensure compliance. To facilitate and enhance the national program, a centralized generator services organization, tasked with providing technical services to the generators on behalf of the national program, is necessary. These subject matter experts are the interface between the generating sites and the disposal facility(s). They provide an invaluable service to the generating organizations through their involvement in waste planning prior to waste generation and through championing implementation of the waste hierarchy. Through their interface, national treatment and transportation services are optimized and new business opportunities are identified. This national model is based on extensive experience in the development and on-going management of a national transuranic waste program and management of the national repository, the Waste Isolation Pilot Plant. The Low Level Program at the Savannah River Site also successfully developed and implemented the waste hierarchy, waste certification and waste generator services concepts presented below. The Savannah River Site

National radon measurement-proficiency program: Individual proficiency report

International Nuclear Information System (INIS)

1992-05-01

In February 1986, the U.S. Environmental Protection Agency (EPA) established the Radon Measurement Proficiency (RMP) Program to assist the public in identifying organizations capable of providing reliable radon measurement services. In December 1991, EPA announced the new individual proficiency listing category in the RMP Program. Individuals applying for this new listing status must demonstrate knowledge of radon measurement fundamentals by passing a written proficiency examination, maintain affiliation with an RMP listed organization, and meet other program requirements. This report lists those individuals who have met the requirements of the RMP Program as of April 30, 1992. These requirements are designed to provide minimum proficiency criteria for individuals who provide radon measurement services on-site in a residential environment

High-level waste management technology program plan

Energy Technology Data Exchange (ETDEWEB)

Harmon, H.D.

1995-01-01

The purpose of this plan is to document the integrated technology program plan for the Savannah River Site (SRS) High-Level Waste (HLW) Management System. The mission of the SRS HLW System is to receive and store SRS high-level wastes in a see and environmentally sound, and to convert these wastes into forms suitable for final disposal. These final disposal forms are borosilicate glass to be sent to the Federal Repository, Saltstone grout to be disposed of on site, and treated waste water to be released to the environment via a permitted outfall. Thus, the technology development activities described herein are those activities required to enable successful accomplishment of this mission. The technology program is based on specific needs of the SRS HLW System and organized following the systems engineering level 3 functions. Technology needs for each level 3 function are listed as reference, enhancements, and alternatives. Finally, FY-95 funding, deliverables, and schedules are s in Chapter IV with details on the specific tasks that are funded in FY-95 provided in Appendix A. The information in this report represents the vision of activities as defined at the beginning of the fiscal year. Depending on emergent issues, funding changes, and other factors, programs and milestones may be adjusted during the fiscal year. The FY-95 SRS HLW technology program strongly emphasizes startup support for the Defense Waste Processing Facility and In-Tank Precipitation. Closure of technical issues associated with these operations has been given highest priority. Consequently, efforts on longer term enhancements and alternatives are receiving minimal funding. However, High-Level Waste Management is committed to participation in the national Radioactive Waste Tank Remediation Technology Focus Area. 4 refs., 5 figs., 9 tabs.

High-level waste management technology program plan

International Nuclear Information System (INIS)

Harmon, H.D.

1995-01-01

The purpose of this plan is to document the integrated technology program plan for the Savannah River Site (SRS) High-Level Waste (HLW) Management System. The mission of the SRS HLW System is to receive and store SRS high-level wastes in a see and environmentally sound, and to convert these wastes into forms suitable for final disposal. These final disposal forms are borosilicate glass to be sent to the Federal Repository, Saltstone grout to be disposed of on site, and treated waste water to be released to the environment via a permitted outfall. Thus, the technology development activities described herein are those activities required to enable successful accomplishment of this mission. The technology program is based on specific needs of the SRS HLW System and organized following the systems engineering level 3 functions. Technology needs for each level 3 function are listed as reference, enhancements, and alternatives. Finally, FY-95 funding, deliverables, and schedules are s in Chapter IV with details on the specific tasks that are funded in FY-95 provided in Appendix A. The information in this report represents the vision of activities as defined at the beginning of the fiscal year. Depending on emergent issues, funding changes, and other factors, programs and milestones may be adjusted during the fiscal year. The FY-95 SRS HLW technology program strongly emphasizes startup support for the Defense Waste Processing Facility and In-Tank Precipitation. Closure of technical issues associated with these operations has been given highest priority. Consequently, efforts on longer term enhancements and alternatives are receiving minimal funding. However, High-Level Waste Management is committed to participation in the national Radioactive Waste Tank Remediation Technology Focus Area. 4 refs., 5 figs., 9 tabs

Mitigation measures and programs in Hungary

Energy Technology Data Exchange (ETDEWEB)

Molnar, S. [Systemexpert Consulting Ltd., Budapest (Hungary)

1996-12-31

In Hungary there are four main governmental programs, which may result in a decrease of emissions of anthropogenic greenhouse gases (GHGs): (1) National program of energy efficiency improvement and energy conservation, (2) Afforestation program, (3) Volatile organic compounds (VOC) emission reduction program, and (4) Program to reduce the use of ozone depleting substances. These ambitious programs were launched in the beginning of the 90`s, but they have been slowed down because of budgetary problems. The comprehensive action plan for mitigation of GHG emissions should be based on these ongoing programs. These programs should be expanded by further measures and programs in order to fulfill the requirements of the FCCC. In the next sections the results and prospects of the above mentioned programs will be summarized. Also the results of the mitigation study supported by the U.S. Country Studies Program are included.

How accurately do instructors judge students' attitudes online? A measurement of expectations and level of satisfaction with an Online Information Systems masters program

Directory of Open Access Journals (Sweden)

Lauren-Nicole Macht

2002-12-01

Full Text Available In order to run a successful educational program, instructors as well as staff members must constantly review and adapt to the expectations, concerns, demographics and satisfaction level of their student consumers. This study was conducted in order to examine these issues in an online educational setting. First, interviews were given to the program instructors in order to determine their opinions about the students' expectations and satisfaction levels. This information was then used to create a student survey that assessed the students' expectations and level of satisfaction. These two sets of results were then compared This comparison revealed that the online instructors did have a good grasp of the online students' expectations, concerns, demographics and satisfaction level. The only areas where the instructors' concepts of student views were slightly less accurate was student concerns and student feelings about the program administration, where the instructors overestimated the level of concern the students had about successfully returning to the learning environment and underestimated the students' satisfaction with the program's administration. This leads us to conclude that, even with the added online factor, instructors strongly understand student expectations, satisfaction levels, demographics and concerns.

Measuring Student Transformation in Entrepreneurship Education Programs

Directory of Open Access Journals (Sweden)

Steven A. Gedeon

2017-01-01

Full Text Available This article describes how to measure student transformation primarily within a university entrepreneurship degree program. Student transformation is defined as changes in knowledge (“Head”, skills (“Hand”, and attitudinal (“Heart” learning outcomes. Following the institutional impact model, student transformation is the primary goal of education and all other program goals and aspects of quality desired by stakeholders are either input factors (professors, courses, facilities, support, etc. or output performance (number of startups, average starting salary, % employment, etc.. This goal-setting framework allows competing stakeholder quality expectations to be incorporated into a continuous process improvement (CPI model when establishing program goals. How to measure these goals to implement TQM methods is shown. Measuring student transformation as the central focus of a program promotes harmony among competing stakeholders and also provides a metric on which other program decisions (e.g., class size, assignments, and pedagogical technique may be based. Different stakeholders hold surprisingly different views on defining program quality. The proposed framework provides a useful way to bring these competing views into a CPI cycle to implement TQM requirements of accreditation. The specific entrepreneurial learning outcome goals described in the tables in this article may also be used directly by educators in nonaccredited programs and single courses/workshops or for other audiences.

Achieving behavioral control with millisecond resolution in a high-level programming environment.

Science.gov (United States)

Asaad, Wael F; Eskandar, Emad N

2008-08-30

The creation of psychophysical tasks for the behavioral neurosciences has generally relied upon low-level software running on a limited range of hardware. Despite the availability of software that allows the coding of behavioral tasks in high-level programming environments, many researchers are still reluctant to trust the temporal accuracy and resolution of programs running in such environments, especially when they run atop non-real-time operating systems. Thus, the creation of behavioral paradigms has been slowed by the intricacy of the coding required and their dissemination across labs has been hampered by the various types of hardware needed. However, we demonstrate here that, when proper measures are taken to handle the various sources of temporal error, accuracy can be achieved at the 1 ms time-scale that is relevant for the alignment of behavioral and neural events.

Measurement of Community Empowerment in Three Community Programs in Rapla (Estonia)

Science.gov (United States)

Kasmel, Anu; Andersen, Pernille Tanggaard

2011-01-01

Community empowerment approaches have been proven to be powerful tools for solving local health problems. However, the methods for measuring empowerment in the community remain unclear and open to dispute. This study aims to describe how a context-specific community empowerment measurement tool was developed and changes made to three health promotion programs in Rapla, Estonia. An empowerment expansion model was compiled and applied to three existing programs: Safe Community, Drug/HIV Prevention and Elderly Quality of Life. The consensus workshop method was used to create the measurement tool and collect data on the Organizational Domains of Community Empowerment (ODCE). The study demonstrated considerable increases in the ODCE among the community workgroup, which was initiated by community members and the municipality’s decision-makers. The increase was within the workgroup, which had strong political and financial support on a national level but was not the community’s priority. The program was initiated and implemented by the local community members, and continuous development still occurred, though at a reduced pace. The use of the empowerment expansion model has proven to be an applicable, relevant, simple and inexpensive tool for the evaluation of community empowerment. PMID:21556179

Measurement of Community Empowerment in Three Community Programs in Rapla (Estonia

Directory of Open Access Journals (Sweden)

Pernille Tanggaard Andersen

2011-03-01

Full Text Available Community empowerment approaches have been proven to be powerful tools for solving local health problems. However, the methods for measuring empowerment in the community remain unclear and open to dispute. This study aims to describe how a context-specific community empowerment measurement tool was developed and changes made to three health promotion programs in Rapla, Estonia. An empowerment expansion model was compiled and applied to three existing programs: Safe Community, Drug/HIV Prevention and Elderly Quality of Life. The consensus workshop method was used to create the measurement tool and collect data on the Organizational Domains of Community Empowerment (ODCE. The study demonstrated considerable increases in the ODCE among the community workgroup, which was initiated by community members and the municipality’s decision-makers. The increase was within the workgroup, which had strong political and financial support on a national level but was not the community’s priority. The program was initiated and implemented by the local community members, and continuous development still occurred, though at a reduced pace. The use of the empowerment expansion model has proven to be an applicable, relevant, simple and inexpensive tool for the evaluation of community empowerment.

Contaminant levels in Gulf of Mexico reef fish after the Deepwater Horizon oil spill as measured by a fishermen-led testing program.

Science.gov (United States)

Fitzgerald, Timothy P; Gohlke, Julia M

2014-01-01

The BP oil disaster posed a significant threat to the U.S. seafood industry. Invertebrates (shrimp, oyster, crab) and other nearshore species comprised the majority of postspill testing by federal and state agencies. Deeper water finfish were sampled less frequently, despite population ranges that overlapped with affected waters. We report on a voluntary testing program with Gulf of Mexico commercial fishermen to ensure the safety of their catch. Seven species of reef fish were tested for polycyclic aromatic hydrocarbons, several metals, and a constituent of Corexit 9500A and 9527A dispersants. Only two of 92 samples had detectable levels of benzo(a)pyrene-equivalents (a combined measure of carcinogenic potency across 7 different PAHs), which were still below federal safety thresholds. PAH ratios for these samples suggest pyrogenic (not petrogenic) contamination - indicating potential sources other than Deepwater Horizon. Metals were largely absent (cadmium, lead) or consistent with levels previously reported (mercury, arsenic). One notable exception was tilefish, which showed mercury concentrations lower than expected. We did not detect dispersant in any of our samples, indicating that it was not present in these species during the study period. Our findings suggest minimal risk to public health from these seafoods as a result of the disaster; however, the most contaminated areas were not sampled through this program.

Value-based performance measures for Hanford Tank Waste Remedition System (TWRS) Program

International Nuclear Information System (INIS)

Keeney, R.L.; von Winterfeldt, D.

1996-01-01

The Tank Waste Remediation Systems (TWRS) Program is responsible for the safe storage, retrieval, treatment, and preparation for disposal of high-level waste currently stored in underground storage tanks at the Hanford site in Richland. The TWRS program has adopted a logical approach to decision making that is based on systems engineering and decision analysis (Westinghouse Hanford Company, 1995). This approach involves the explicit consideration of stakeholder values and an evaluation of the TWRS alternatives in terms of these values. Such evaluations need to be consistent across decisions. Thus, an effort was undertaken to develop a consistent, quantifiable set of measures that can be used by TVVRS to assess alternatives against the stakeholder values. The measures developed also met two additional requirements: 1) the number of measure should be relatively small; and 2) performance with respect to the measures should be relatively easy to estimate

The New Brunswick Laboratory Safeguards Measurement Evaluation Program

International Nuclear Information System (INIS)

Cacic, C.G.; Trahey, N.M.; Zook, A.C.

1987-01-01

The New Brunswick Laboratory (NBL) has been tasked by the U.S. Department of Energy (DOE) Office of Safeguards and Security (OSS) to assess and evaluate the adequacy of measurement technology as applied to materials accounting in DOE nuclear facilities. The Safeguards Measurement Evaluation (SME) Program was developed as a means to monitor and evaluate the quality and effectiveness of accounting measurements by site, material balance area (MBA), or unit process. Phase I of the SME Program, initiated during 1985, involved evaluation of the primary accountability measurement methods at six DOE Defense Programs facilities: Savannah River Plant, Portsmouth Gaseous Diffusion Plant, Y-12 Plant, Rocky Flats Plant, Rockwell Hanford Operations, and NBL. Samples of uranyl nitrate solution, dried plutonium nitrates, and plutonium oxides were shipped to the participants for assay and isotopic abundance measurements. Resulting data are presented and evaluated as indicators of current state-of-the-practice accountability measurement methodology, deficiencies in materials accounting practices, and areas for possible assistance in upgrading measurement capabilities. Continuing expansion of the SME Program to include materials which are representative of specific accountability measurement points within the DOE complex is discussed

Requirements for an ES and H assurance program at the working levels of organization

International Nuclear Information System (INIS)

Tierney, M.S.; Ellingson, A.C.

1979-07-01

Means by which the disciplines of quality assurance (QA), reliability (R), and human factors (HF) might be used to the advantage of Environment, Safety, and Health (ES and H) programs are being investigated. A generalized model assurance program, based on QA, R, and HF principles but specifically tailored to ES and H program needs, has been developed. Current studies address implementation of the model assurance program at the working levels of organization. It appears that the only way practicability at the working level can be determined is by the case study method. The present study represents a first step in the application of such a procedure. An attempt was made to approach the question of practicability by first constructing a generic ES and H assurance plan for working-level organizations that is based upon the more widely-applied model plan and studies mentioned earlier. Then the elements of this generic working-level plan were compared with the practices of an existing R and D organization at Sandia Laboratories, Albuquerque. Some of the necessary steps were taken to convert these practices to those required by the generic plan in order to gain a measure of the feasibility, cost, and some of the possible benefits of such a conversion. Partial results of one case study are presented, and some generalizations that emerge regarding the structure of an idealized working-level ES and H plan are made

Can You See the Stars? Citizen-Science Programs to Measure Night Sky Brightness

Science.gov (United States)

Walker, Constance E.

2009-05-01

For the IYA2009 Dark Skies Awareness Cornerstone Project, partners in dark-sky, astronomy and environmental education are promoting three citizen-scientist programs that measure light pollution at local levels worldwide. These programs take the form of "star hunts", providing people with fun and direct ways to acquire heightened awareness about light pollution through first-hand observations of the night sky. Together the programs are spanning the entire IYA, namely: GLOBE at Night in March, Great World Wide Star Count in October, and How Many Stars during the rest of the year. Citizen-scientists - students, educators, amateur astronomers and the general public - measure the darkness of their local skies and contribute observations online to a world map. Anyone anywhere anytime can look within particular constellations for the faintest stars and match them to one of seven star maps. For more precise measurements, digital sky-brightness meters can be used. Measurements, along with the measurement location, time, and date, are submitted online, and within a few days to weeks a world map showing results is available. These measurements can be compared with data from previous years, as well as with satellite data, population densities, and electrical power-usage maps. Measurements are available online via Google Earth or other tools and as downloadable datasets. Data from multiple locations in one city or region are especially interesting, and can be used as the basis of a class project or science fair experiment, or even to inform the development of public policy. In the last few years these programs successfully conducted campaigns in which more than 35,000 observations were submitted from over 100 countries. The presentation will provide an update, describe how people can become involved and take a look ahead at the program's sustainability. For further information about these and other Dark Skies Awareness programs, please visit www.darkskiesawareness.org.

Measuring Confidence Levels of Male and Female Students in Open Access Enabling Courses

Science.gov (United States)

Atherton, Mirella

2015-01-01

The study of confidence was undertaken at the University of Newcastle with students selecting science courses at two campuses. The students were enrolled in open access programs and aimed to gain access to undergraduate studies in various disciplines at University. The "third person effect" was used to measure the confidence levels of…

US program for the immobilization of high-level nuclear wastes

International Nuclear Information System (INIS)

Crandall, J.L.

1979-01-01

A program has been developed for long-term management of high-level nuclear waste. The Savannah River Operations Office of the US Department of Energy is acting as the lead office for this program with technical advice from the E.I. du Pont de Nemours and Company. The purpose of the long-term program is to immobilize the DOE high-level waste in forms that act as highly efficient barriers against radionuclide release to the disposal site and to provide technology for similar treatment of commercial high-level waste in case reprocessing of commercial nuclear fuels is ever resumed. Descriptions of existing DOE and commercial wastes, program strategy, program expenditures, development of waste forms, evaluation and selection of waste forms, regulatory aspects of waste form selection, project schedules, and cost estimates for immobilization facilities are discussed

TEACHING OBJECT ORIENTED PROGRAMMING AT THE INTRODUCTORY LEVEL

OpenAIRE

OKUR , Prof.Dr. Mehmet C.

2006-01-01

Teaching object oriented programming has become a rapidly expanding preference at various educational environments. However, teachers usually experience problems when introducing object oriented concepts and programming to beginners. How to teach the fundamentals of object oriented programming at an introductory level course is still a common subject for debate. In this paper, an evaluation of these problems is presented and some possible approaches for improving the quality and success of su...

Method for steam generator water level measurement

International Nuclear Information System (INIS)

Srinivasan, J.S.

1991-01-01

This paper describes a nuclear power plant, a method of controlling the steam generator water level, wherein the steam generator has an upper level tap corresponding to an upper level, a lower level, a riser positioned between the lower and upper taps, and level sensor means for indicating water level between a first range limit and a second range limit, the sensor means being connected to at least the lower tap. It comprises: calculating a measure of velocity head at about the lower level tap; calculating a measure of full water level as the upper level less the measure of velocity head; calibrating the level sensor means to provide an output at the first limit corresponding to an input thereto representative of the measure of full level; calculating a high level setpoint equal to the level of the riser less a bias amount which is a function of the position of the riser relative to the span between the taps; and controlling the water level when the sensor means indicates that the high level setpoint has been reached

Solid, low-level radioactive waste certification program

International Nuclear Information System (INIS)

Grams, W.H.

1991-11-01

The Hanford Site solid waste treatment, storage, and disposal facilities accept solid, low-level radioactive waste from onsite and offsite generators. This manual defines the certification program that is used to provide assurance that the waste meets the Hanford Site waste acceptance criteria. Specifically, this program defines the participation and responsibilities of Westinghouse Hanford Company Solid Waste Engineering Support, Westinghouse Hanford Company Quality Assurance, and both onsite and offsite waste generators. It is intended that waste generators use this document to develop certification plans and quality assurance program plans. This document is also intended for use by Westinghouse Hanford Company solid waste technical staff involved in providing assurance that generators have implemented a waste certification program. This assurance involves review and approval of generator certification plans, and review of generator's quality assurance program plans to ensure that they address all applicable requirements. The document also details the Westinghouse Hanford Company Waste Management Audit and Surveillance Program. 5 refs

Measurement assurance program for FTIR analyses of deuterium oxide samples

International Nuclear Information System (INIS)

Johnson, S.R.; Clark, J.P.

1997-01-01

Analytical chemistry measurements require an installed criterion based assessment program to identify and control sources of error. This program should also gauge the uncertainty about the data. A self- assessment was performed of long established quality control practices against the characteristics of a comprehensive measurement assurance program. Opportunities for improvement were identified. This paper discusses the efforts to transform quality control practices into a complete measurement assurance program. The resulting program heightened the laboratory's confidence in the data it generated, by providing real-time statistical information to control and determine measurement quality

National energy peak leveling program (NEPLP). Final report

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

This three-volume report is responsive to the requirements of Contract E (04-3)-1152 to provide a detailed methodology, to include management, technology, and socio-economic aspects, of a voluntary community program of computer-assisted peak load leveling and energy conservation in commercial community facilities. The demonstration project established proof-of-concept in reducing the kW-demand peak by the unofficial goal of 10%, with concurrent kWh savings. This section of the three volume report is a final report appendix with information on the National Energy Peak Leveling Program (NEPLP).

Atmospheric Radiation Measurement Program facilities newsletter, January 2001.; TOPICAL

International Nuclear Information System (INIS)

Holdridge, D. J.

2001-01-01

In the realm of global climate modeling, numerous variables affect the state of the atmosphere and climate. One important area is soil moisture and temperature. The ARM Program uses several types of instruments to gather soil moisture information. An example is the soil water and temperature system (SWATS). A SWATS is located at each of 21 extended facility sites within the CART site boundary. Each system is configured to measure soil moisture and temperature at eight distinct subsurface levels. A special set of probes used in the SWATS measures soil temperature, soil-water potential, and volumetric water content. Sensors are placed at eight different depths below the soil surface, starting at approximately 5 cm (2 in.) below the surface and ending as deep as 175 cm (69 in.). Each site has two identical sets of probes buried 1 m (3.3 ft) apart, to yield duplicate measurements as a quality control measure. At some sites, impenetrable soil or rock layers prevented installation of probes at the deeper levels. The sensors are connected to an electronic data logger that collects and stores the data. Communication equipment transfers data from the site. All of the electronic equipment is housed in a weatherproof enclosure mounted on a concrete slab

Retention in Differentiated Care: Multiple Measures Analysis for a Decentralized HIV Care and Treatment Program in North Central Nigeria

Science.gov (United States)

Agaba, Patricia A; Genberg, Becky L; Sagay, Atiene S; Agbaji, Oche O; Meloni, Seema T; Dadem, Nancin Y; Kolawole, Grace O; Okonkwo, Prosper; Kanki, Phyllis J; Ware, Norma C

2018-01-01

Objective Differentiated care refers collectively to flexible service models designed to meet the differing needs of HIV-infected persons in resource-scarce settings. Decentralization is one such service model. Retention is a key indicator for monitoring the success of HIV treatment and care programs. We used multiple measures to compare retention in a cohort of patients receiving HIV care at “hub” (central) and “spoke” (decentralized) sites in a large public HIV treatment program in north central Nigeria. Methods This retrospective cohort study utilized longitudinal program data representing central and decentralized levels of care in the Plateau State Decentralization Initiative, north central Nigeria. We examined retention with patient- level (retention at fixed times, loss-to-follow-up [LTFU]) and visit-level (gaps-in-care, visit constancy) measures. Regression models with generalized estimating equations (GEE) were used to estimate the effect of decentralization on visit-level measures. Patient-level measures were examined using survival methods with Cox regression models, controlling for baseline variables. Results Of 15,650 patients, 43% were enrolled at the hub. Median time in care was 3.1 years. Hub patients were less likely to be LTFU (adjusted hazard ratio (AHR)=0.91, 95% CI: 0.85-0.97), compared to spoke patients. Visit constancy was lower at the hub (−4.5%, 95% CI: −3.5, −5.5), where gaps in care were also more likely to occur (adjusted odds ratio=1.95, 95% CI: 1.83-2.08). Conclusion Decentralized sites demonstrated better retention outcomes using visit-level measures, while the hub achieved better retention outcomes using patient-level measures. Retention estimates produced by incorporating multiple measures showed substantial variation, confirming the influence of measurement strategies on the results of retention research. Future studies of retention in HIV care in sub-Saharan Africa will be well-served by including multiple measures

Worker-Level and Firm-Level Effects of a Wage Subsidy Program for Highly Educated Labor

DEFF Research Database (Denmark)

Kaiser, Ulrich; Kuhn, Johan Moritz

and firms, we find that the program had positive effects on employment and wages the year individuals participate in the program. For wages, we also find positive and statistically significant effects for the two subsequent years. At the program participating firm level, we find statistically significant...

Worker-level and Firm-level Effects of a Wage Subsidy Program for Highly Educated Labor

DEFF Research Database (Denmark)

Kaiser, Ulrich; Kuhn, Johan Moritz

2016-01-01

and annual earnings during program participation while there are no positive effects for the years after program expiration. At the employer-level, we find statistically significant effects on the number of highly educated employees for both the period of program participation and the subsequent time period...

Water level measurement uncertainty during BWR instability

International Nuclear Information System (INIS)

Torok, R.C.; Derbidge, T.C.; Healzer, J.M.

1994-01-01

This paper addresses the performance of the water-level measurement system in a boiling water reactor (BWR) during severe instability oscillations which, under some circumstances, can occur during an anticipated transient without SCRAM (ATWS). Test data from a prototypical mock-up of the water-level measurement system was used to refine and calibrate a water-level measurement system model. The model was then used to predict level measurement system response, using as boundary conditions vessel pressures calculated by ppercase RETRAN for an ATWS/instability event.The results of the study indicate that rapid pressure changes in the reactor pressure vessel which cause oscillations in downcomer water level, coupled with differences in instrument line lengths, can produce errors in the sensed water level. Using nominal parameters for the measurement system components, a severe instability transient which produced a 0.2 m peak-to-minimum water-level oscillation in the vessel downcomer was predicted to produce pressure difference equivalent to a 0.7 m level oscillation at the input to the differential pressure transmitter, 0.5 m oscillation at the output of the transmitter, and an oscillation of 0.3 m on the water-level indicator in the control room. The level measurement system error, caused by downcomer water-level oscillations and instrument line length differential, is mitigated by damping both in the differential pressure transmitter used to infer level and in the control room display instrument. ((orig.))

MEASURING INSTRUMENT CONSTRUCTION AND VALIDATION IN ESTIMATING UNICYCLING SKILL LEVEL

Directory of Open Access Journals (Sweden)

Ivan Granić

2012-09-01

Full Text Available Riding the unicycle presupposes the knowledge of the set of elements which describe motoric skill, or just part of that set with which we could measure the level of that knowledge. Testing and evaluation of the elements is time consuming. In order to design a unique, composite measuring instrument, to facilitate the evaluation of the initial level of unicycling skill, we tested 17 recreative subjects who were learning to ride the unicycle in 15 hours of training, without any previous knowledge or experience what was measured before the beginning of the training. At the beginning and at the end of the training they were tested with the set of the 12 riding elements test that was carried out to record only successful attempts, followed by unique SLALOM test which include previously tested elements. It was found that the unique SLALOM test has good metric features and a high regression coefficient showed that the SLALOM could be used instead of the 12 elements of unicycle riding skill, and it could be used as a uniform test to evaluate learned or existing knowledge. Because of its simplicity in terms of action and simultaneous testing of more subjects, the newly constructed test could be used in evaluating the unicycling recreational level, but also for monitoring and programming transformation processes to develop the motor skills of riding of unicycle. Because of its advantages, it is desirable to include unicycling in the educational processes of learning new motor skills, which can be evaluated by the results of this research. The obtained results indicate that the unicycle should be seriously consider as a training equipment to “refresh” or expand the recreational programs, without any fear that it is just for special people. Namely, it was shown that the previously learned motor skills (skiing, roller-skating, and cycling had no effect on the results of final testing.

Levels of Use and Extent of Implementation of New Programs in Teacher Education Institutions: What Do You Do?

Science.gov (United States)

Hall, Gene E.

An eight-level table of Levels of Use (LoU) is employed to measure the adoption and eventual success of program innovations in teacher education institutions. Speculations on the success or failure of attempted innovations, backed with statistical analysis, are presented. (SAS)

A level stimulator programmed for audiometry

International Nuclear Information System (INIS)

Fayart, Gerard

1976-02-01

This stimulator has been designed for automated audiometric experiments on lemurians. The variations of the transmission level are programmed on punched tape whose reading is controlled by an audiofrequency attenuator. The positive answers of the animal are stored in a seven-counter memory and the results are read by display [fr

Performance expectations of measurement control programs

International Nuclear Information System (INIS)

Hammond, G.A.

1985-01-01

The principal index for designing and assessing the effectiveness of safeguards is the sensitivity and reliability of gauging the true status of material balances involving material flows, transfers, inventories, and process holdup. The measurement system must not only be capable of characterizing the material for gradation or intensity of protection, but also be responsive to needs for detection and localization of losses, provide confirmation that no diversion has occurred, and help meet requirements for process control, health and safety. Consequently, the judicious application of a measurement control and quality assurance program is vital to a complete understanding of the capabilities and limitations of the measurement system including systematic and random components of error for weight, volume, sampling, chemical, isotopic, and nondestructive determinations of material quantities in each material balance area. This paper describes performance expectations or criteria for a measurement control program in terms of ''what'' is desired and ''why'', relative to safeguards and security objectives

Method of measuring reactor water level

International Nuclear Information System (INIS)

Shinohara, Kaoru.

1979-01-01

Purpose: To provide a water level measuring system so that a reactor water level detecting signal can be corrected in correspondence to a recirculation flow, thereby to carry out a correct water level detection in a wide range of the reactor. Method: According to the operation record of a precursor reactor, the ratio Δh of the lowering of the water level due to the recirculation flow is lowered in proportion to the ratiowith respect to the rated differential pressure of the recirculation flow. Accordingly, the flow of recirculation pump is measured by an elbow differential pressure generator utilizing an elbow of a pipe, and the measured value is multiplied by a gain by a ratio setter, and therefter, an addition computation is carried out by an adder for correcting the signal from a water level detector. When the signal from the water level detector is corrected in this manner, the influence of the lowering of the water level due to the recirculation flow can be removed, and an interlocker predetermined in the defined water level can be actuated, thus the influence of the dynamic pressure due to the recirculation flow acting on the instrumental pipe line detecting the reactor water level can be removed effectively. (Yoshino, Y.)

Adapting high-level language programs for parallel processing using data flow

Science.gov (United States)

Standley, Hilda M.

1988-01-01

EASY-FLOW, a very high-level data flow language, is introduced for the purpose of adapting programs written in a conventional high-level language to a parallel environment. The level of parallelism provided is of the large-grained variety in which parallel activities take place between subprograms or processes. A program written in EASY-FLOW is a set of subprogram calls as units, structured by iteration, branching, and distribution constructs. A data flow graph may be deduced from an EASY-FLOW program.

The High Level Vibration Test Program

International Nuclear Information System (INIS)

Hofmayer, C.H.; Curreri, J.R.; Park, Y.J.; Kato, W.Y.; Kawakami, S.

1989-01-01

As part of cooperative agreements between the United States and Japan, tests have been performed on the seismic vibration table at the Tadotsu Engineering Laboratory of Nuclear Power Engineering Test Center (NUPEC) in Japan. The objective of the test program was to use the NUPEC vibration table to drive large diameter nuclear power piping to substantial plastic strain with an earthquake excitation and to compare the results with state-of-the-art analysis of the problem. The test model was designed by modifying the 1/2.5 scale model of the PWR primary coolant loop. Elastic and inelastic seismic response behavior of the test model was measured in a number of test runs with an increasing excitation input level up to the limit of the vibration table. In the maximum input condition, large dynamic plastic strains were obtained in the piping. Crack initiation was detected following the second maximum excitation run. The test model was subjected to a maximum acceleration well beyond what nuclear power plants are designed to withstand. This paper describes the overall plan, input motion development, test procedure, test results and comparisons with pre-test analysis. 4 refs., 16 figs., 2 tabs

The High Level Vibration Test program

International Nuclear Information System (INIS)

Hofmayer, C.H.; Curreri, J.R.; Park, Y.J.; Kato, W.Y.; Kawakami, S.

1990-01-01

As part of cooperative agreements between the United States and Japan, tests have been performed on the seismic vibration table at the Tadotsu Engineering Laboratory of Nuclear Power Engineering Test Center (NUPEC) in Japan. The objective of the test program was to use the NUPEC vibration table to drive large diameter nuclear power piping to substantial plastic strain with an earthquake excitation and to compare the results with state-of-the-art analysis of the problem. The test model was designed by modifying the 1/2.5 scale model of the pressurized water reactor primary coolant loop. Elastic and inelastic seismic response behavior of the test model was measured in a number of test runs with an increasing excitation input level up to the limit of the vibration table. In the maximum input condition, large dynamic plastic strains were obtained in the piping. Crack initiation was detected following the second maximum excitation run. The test model was subjected to a maximum acceleration well beyond what nuclear power plants are designed to withstand. This paper describes the overall plan, input motion development, test procedure, test results and comparisons with pre-test analysis

Solar Modulation of Atmospheric Cosmic Radiation:. Comparison Between In-Flight and Ground-Level Measurements

Science.gov (United States)

Iles, R. H. A.; Taylor, G. C.; Jones, J. B. L.

January 2000 saw the start of a collaborative study involving the Mullard Space Science Laboratory, Virgin Atlantic Airways, the Civil Aviation Authority and the National Physical Laboratory in a program to investigate the cosmic radiation exposure to aircrew. The study has been undertaken in view of EU Directive 96/291 (May 2000) which requires the assessment of the level of radiation exposure to aircrew. The project's aims include validation of radiation dose models and evaluation of space weather effects on atmospheric cosmic radiation levels, in particular those effects not accounted for by the models. Ground level measurements are often used as a proxy for variations in cosmic radiation dose levels at aircraft altitudes, especially during Forbush Decreases (FDs) and Solar Energetic Particle (SEP) events. Is this estimation realistic and does the ground level data accurately represent what is happening at altitude? We have investigated the effect of a FD during a flight from Hong Kong to London Heathrow on the 15th July 2000 and compared count rate and dose measurements with simultaneous variations measured at ground level. We have also compared the results with model outputs.

Recommended regulatory program plan for low-level radioactive waste management in Maryland

International Nuclear Information System (INIS)

1986-01-01

The National Program for Low-Level Radioactive Waste Management was instituted by the US Department of Energy to assist the states in carrying out this new federal policy. Based on the premise that the safe disposal of low-level waste is technologically feasible and that states have the necessary degree of authority to set management policy, the National Program is helping them to develop a responsive, comprehensive regulatory program. The State of Maryland is actively engaged with the National Program in its efforts to form a comprehensive management program. The purpose of this plan is to review existing statutory and regulatory program responsibilities and provide a recommended management scheme for low-level radioactive waste

Improvements on Low Level Activity Gamma Measurements and X-ray Spectrometry at the CEA-MADERE Measurement Platform

Directory of Open Access Journals (Sweden)

Sergeyeva Victoria

2016-01-01

Full Text Available The CEA MADERE platform (Measurement Applied to DosimEtry in REactors is a part of the Instrumentation Sensors and Dosimetry Laboratory (LDCI. This facility is dedicated to the specific activity measurements of solid and radioactive samples using Gamma and X-ray spectrometry. MADERE is a high-performance facility devoted to neutron dosimetry for experimental programs performed in CEA and for the irradiation surveillance programmes of PWR vessels. The MADERE platform is engaged in a continuous improvement process. Recently, two High Efficiency diodes have been integrated to the MADERE platform in order to manage the accurate low level activity measurements (few Bq per sample. This new equipment provides a good level of efficiency over the energy range from 60 keV to 2 MeV. The background continuum is reduced due to the use of a Ultra Low Background (ULB lead shielding. Relative and absolute X-ray measurement techniques have been improved in order to facilitate absolute rhodium activity measurement (Rh103m on solid samples. Additional efforts have been made to increase the accuracy of the relative niobium (Nb93m activity measurement technique. The way of setting up an absolute measurement method for niobium is under investigation. After a presentation of the MADERE's measurement devices, this paper focuses on the technological options taken into account for the design of high efficiency measurement devices. Then, studies performed on X-ray measurement techniques are presented. Some details about the calculation of uncertainties and correction factors are also mentioned. Finally, future research and development axes are exposed.

Measuring healthcare productivity - from unit to system level.

Science.gov (United States)

Kämäräinen, Vesa Johannes; Peltokorpi, Antti; Torkki, Paulus; Tallbacka, Kaj

2016-04-18

Purpose - Healthcare productivity is a growing issue in most Western countries where healthcare expenditure is rapidly increasing. Therefore, accurate productivity metrics are essential to avoid sub-optimization within a healthcare system. The purpose of this paper is to focus on healthcare production system productivity measurement. Design/methodology/approach - Traditionally, healthcare productivity has been studied and measured independently at the unit, organization and system level. Suggesting that productivity measurement should be done in different levels, while simultaneously linking productivity measurement to incentives, this study presents the challenges of productivity measurement at the different levels. The study introduces different methods to measure productivity in healthcare. In addition, it provides background information on the methods used to measure productivity and the parameters used in these methods. A pilot investigation of productivity measurement is used to illustrate the challenges of measurement, to test the developed measures and to prove the practical information for managers. Findings - The study introduces different approaches and methods to measure productivity in healthcare. Practical implications - A pilot investigation of productivity measurement is used to illustrate the challenges of measurement, to test the developed measures and to prove the practical benefits for managers. Originality/value - The authors focus on the measurement of the whole healthcare production system and try to avoid sub-optimization. Additionally considering an individual patient approach, productivity measurement is examined at the unit level, the organizational level and the system level.

A Study of Army Civilian Entry Level and Mid-Level Program Management Leadership Development

Science.gov (United States)

2016-05-08

and mid-grade level positions is an important responsibility for senior leaders. Mentoring and coaching entry level and mid-grade level...Program Management Leadership Development Craig J. Maurice Defense Acquisition University Senior Service College Fellowship 2015-2016 Huntsville...requirements for the Army’s Senior Service College Fellowship (SSCF) under the direction of SSCF Director, Mr. John Daniels and Research Advisor, Mr. Van

Measuring the Level of Socialization in Children with Autism Spectrum Disorder

Directory of Open Access Journals (Sweden)

Khaustov A.V.,

2016-10-01

Full Text Available Difficulties with socialization common for children with autism spectrum disorder (ASD are a serious problem for their inclusion into educational settings. These socialization deficits are basically related to underdeveloped social skills. The paper describes a study aimed at revealing the level of socialization in children with ASD. The study involved 117 children aged 5–7 years and their parents. The children’s socialization level was measured with the Vineland Adaptive Behavior Scale. The outcomes showed that most children with ASD display low levels of socialization resulting in their inability to adequately communicate and cooperate with other people as in play, as in everyday life. Two factors were found to affect the level of socialization in the children: deficit of motivation and specific cognitive impairments. The paper argues for the necessity of developing a program for psychologi- cal and educational assistance aimed at forming social skills in children with ASD.

Association between self-reported and objectively measured physical fitness level in a middle-aged population in primary care

DEFF Research Database (Denmark)

Obling, Kirstine H.; Hansen, Anne-Louise Smidt; Overgaard, Kristian

2015-01-01

fitness level were cross-tabulated and agreement was quantified by Kappa statistics. Gender differences within categories were investigated by Poisson regression. RESULTS: Data from 996 men and 1017 women were analyzed (excluded, n = 303). In both men and women a higher self-reported fitness level......AIM: To investigate the association between self-reported physical fitness level obtained by a single-item question and objectively measured fitness level in 30- to 49-year-old men and women. METHODS: From the Danish 'Check Your Health Preventive Program' 2013-2014 fitness level was assessed...... in 2316 participants using the Aastrand test. Additionally, participants rated their physical fitness as high, good, average, fair or low. The association of self-reported- with objectively measured fitness level was analyzed by linear regression. Categories of self-reported- and objectively measured...

Optimizing measurement sensitivity to facilitate monitoring environmental levels of Rn-daughter concentrations

International Nuclear Information System (INIS)

Keefe, D.J.; McDowell, W.P.; Groer, P.G.; Witek, R.T.

1977-01-01

In the measurement of environmental levels of radioactivity, the primary problem is the accumulation of a statistically meaningful number of counts within a reasonable period of time. In the case of measurements of airborne 222 Rn-daughter concentrations, the problem is further complicated by the particularly short half-life, 3.05 minutes, of RaA (Po 218 ). Since the Rn-daughters, (RaA, RaB [Pb 214 ] and RaC [Bi 214 ]) are of interest, the equations interrelating these Rn-daughter concentrations were derived from the laws of radioactive-series decay. These equations, although straightforward, are cumbersome to solve. To facilitate the efficient use of these equations, a computer program has been written which permits the calculation of Rn-daughter concentrations or expected counts for a given set of measurement parameters (flow rate and detector efficiencies). A subroutine then calculates the optimum pumping and counting times required to provide the number of counts necessary for acceptable statistics at environmental levels of 222 Rn-daughter concentrations. This subroutine contains a set of parameters, flow rate and efficiencies, that are fixed using realistic restrictions. The use of these optimized pumping and counting times results in maximum measurement sensitivity under realistic constraints

Status of the high-level nuclear waste disposal program in Japan

International Nuclear Information System (INIS)

Uematsu, K.

1985-01-01

The Japan Atomic Energy Commission (JAEC) initiated a high-level radioactive waste disposal program in 1976. Since then, the Advisory Committee on Radioactive Waste Management of JAEC has revised the program twice. The latest revision was issued in 1984. The committee recommended a four-phase program and the last phase calls for the beginning of emplacement of the high-level nuclear waste into a selected repository in the Year 2000. The first phase is already completed, and the second phase of this decade calls for the selection of a candidate disposal site and the conducting of the RandD of waste disposal in an underground research laboratory and in a hot test facility. This paper covers the current status of the high-level nuclear waste disposal program in Japan

Usage of I++ Simulator to Program Coordinate Measuring Machines when Common Programming Methods are difficult to apply

Directory of Open Access Journals (Sweden)

Gąska A.

2014-02-01

Full Text Available Nowadays, simulators facilitate tasks performed daily by the engineers of different branches, including coordinate metrologists. Sometimes it is difficult or almost impossible to program a Coordinate Measuring Machine (CMM using standard methods. This happens, for example, during measurements of nano elements or in cases when measurements are performed on high-precision (accurate measuring machines which work in strictly air-conditioned spaces and the presence of the operator in such room during the programming of CMM could cause an increase in temperature, which in turn could make it necessary to wait some time until conditions stabilize. This article describes functioning of a simulator and its usage during Coordinate Measuring Machine programming in the latter situation. Article also describes a general process of programming CMMs which ensures the correct machine performance after starting the program on a real machine. As an example proving the presented considerations, measurement of exemplary workpiece, which was performed on the machine working in the strictly air-conditioned room, was described

An iterative method for tri-level quadratic fractional programming problems using fuzzy goal programming approach

Science.gov (United States)

Kassa, Semu Mitiku; Tsegay, Teklay Hailay

2017-08-01

Tri-level optimization problems are optimization problems with three nested hierarchical structures, where in most cases conflicting objectives are set at each level of hierarchy. Such problems are common in management, engineering designs and in decision making situations in general, and are known to be strongly NP-hard. Existing solution methods lack universality in solving these types of problems. In this paper, we investigate a tri-level programming problem with quadratic fractional objective functions at each of the three levels. A solution algorithm has been proposed by applying fuzzy goal programming approach and by reformulating the fractional constraints to equivalent but non-fractional non-linear constraints. Based on the transformed formulation, an iterative procedure is developed that can yield a satisfactory solution to the tri-level problem. The numerical results on various illustrative examples demonstrated that the proposed algorithm is very much promising and it can also be used to solve larger-sized as well as n-level problems of similar structure.

Status update on the NIFFTE high precision fission cross section measurement program

International Nuclear Information System (INIS)

Laptev, Alexander B.; Tovesson, Fredrik; Burgett, Eric; Greife, Uwe; Grimes, Steven; Heffner, Michael D.; Hertel, Nolan E.; Hill, Tony; Isenhower, Donald; Klay, Jennifer L.; Kornilov, Nickolay; Kudo, Ryuho; Loveland, Walter; Massey, Thomas; McGrath, Chris; Pickle, Nathan; Qu, Hai; Sharma, Sarvagya; Snyder, Lucas; Thornton, Tyler; Towell, Rusty S.; Watson, Shon

2010-01-01

The Neutron Induced Fission Fragment Tracking Experiment (NIFFTE) program has been underway for nearly two years. The program's mission is to measure fission cross sections of the primary fissionable and fissile materials ( 235 U, 239 Pu, 238 U) as well as the minor actinides across energies from approximately 50 keV up to 20 MeV with an absolute uncertainty of less than one percent while investigating energy ranges from below an eV to 600 MeV. This basic nuclear physics data is being reinvestigated to support the next generation power plants and a fast burner reactor program. Uncertainties in the fast, resolved and unresolved resonance regions in plutonium and other transuranics are extremely large, dominating safety margins in the next generation nuclear power plants and power plants of today. This basic nuclear data can be used to support all aspects of the nuciear renaissance. The measurement campaign is utilizing a Time Projection Chamber or TPC as the tool to measure these cross sections to these unprecedented levels. Unlike traditional fission cross section measurements using time-of-flight and a multiple fission foil configurations in which fission cross sections in relation to that of 235 U are performed, the TPC project uses time-of-flight and hydrogen as the benchmark cross section. Using the switch to hydrogen, a simple, smooth cross section that can be used which removes the uncertainties associated with the resolved and unresolved resonances in 235 U.

The NRC measurement verification program

International Nuclear Information System (INIS)

Pham, T.N.; Ong, L.D.Y.

1995-01-01

A perspective is presented on the US Nuclear Regulatory Commission (NRC) approach for effectively monitoring the measurement methods and directly testing the capability and performance of licensee measurement systems. A main objective in material control and accounting (MC and A) inspection activities is to assure the accuracy and precision of the accounting system and the absence of potential process anomalies through overall accountability. The primary means of verification remains the NRC random sampling during routine safeguards inspections. This involves the independent testing of licensee measurement performance with statistical sampling plans for physical inventories, item control, and auditing. A prospective cost-effective alternative overcheck is also discussed in terms of an externally coordinated sample exchange or ''round robin'' program among participating fuel cycle facilities in order to verify the quality of measurement systems, i.e., to assure that analytical measurement results are free of bias

[Effectiveness of a nutritional education program in lowering blood cholesterol levels in a public health center].

Science.gov (United States)

Seki, M; Yamaguchi, T

1993-06-01

An educational program for persons found to have high blood cholesterol during health examinations at the Nerima Public Health Center was begun in April, 1989. This program was differed from the usual program in two areas. First, new educational material was developed consisting of a check list of 30 items to assess eating patterns. By checking these items, participants could gain an understanding of what they should change in their eating behavior. Secondly, the table of restricted foods was not used. Participants were advised to achieve healthy eating patterns and followed up with a nutritional consultation that was held after three months, at which time they were interviewed regarding compliance and had their blood cholesterol levels measured. The effectiveness of the new educational program and the relationship between achievement of healthy eating patterns and reduction in blood cholesterol levels were analyzed. The main results were as follows: 1) In subjects (n = 79) who received the new education program in 1989-1990, serum cholesterol levels showed significant reduction, as compared with controls (n = 38) who received the usual education program in 1988-1989. 2) Subjects were divided into three groups according to their changes in serum cholesterol levels,--normalized, improved and unimproved--and the number of items complied with were counted for analysis. The mean score of compliance was highest in the normalized group with significant difference between the normalized and the unimproved groups. 3) The items of the high compliance score in the normalized group were in order of high score "to decrease high-fat meats", "to decrease cakes", "to choose lean meats and poultry without skin" and "to eat vegetables at every meal".

Evaluating public involvement in the National Low-Level Radioactive Waste Management Program

International Nuclear Information System (INIS)

1982-09-01

The Department of Energy contracted with the Keystone Center to evaluate the effectiveness of the National Low-Level Radioactive Waste Management Program's public-involvement efforts. The Center chose six evaluators with diverse training and experience related to low-level waste management and public-participation programs. Keystone's evaluation was based on (a) observations by the evaluators who attended the National Program-sponsored strategy review meetings and fairs; (b) interviews with low-level waste generators, local government officials, state legislators, public-interest groups, and members of the general public; and (c) observations of the final National Program strategy task force meeting. The evaluators concluded that, overall, the public-participation processes yielded some very positive results - for policy development and for DOE and the EG and G staff. They judged the strategy document to be complete, concise, and helpful to public dialogue on low-level waste issues. They also made specific recommendations for improvements to the public-participation program

Micronesian Mathematics Program, Level 1, Children's Workbook.

Science.gov (United States)

Gring, Carolyn

This workbook for children was prepared especially to accompany the level 1 Micronesian Mathematics Program Teacher's Guide. It is to be used to check whether children have learned concepts taught by activities and activity cards. Work is provided for such concepts as color recognition, categorizing, counting, ordering, numeration, contrasting,…

Programming the control of magnetic field measurements

International Nuclear Information System (INIS)

David, L.

1998-01-01

This paper gives a short review concerning the new NMR probe measurement control system. Then it presents the new program 'CYCLOCHAMP' attached to the magnetic field measurement which also allows to cycle the magnetic field inside the cyclotrons and to equilibrate it among the SSC sectors. (authors)

235U Holdup Measurement Program in support of facility shutdown

International Nuclear Information System (INIS)

Thomason, R.S.; Griffin, J.C.; Lien, O.G.; McElroy, R.D.

1991-01-01

In 1989, the Department of Energy directed shutdown of an enriched uranium processing facility at Savannah River Site. As part of the shutdown requirements, deinventory and cleanout of process equipment and nondestructive measurement of the remaining 235 U holdup were required. The holdup measurements had safeguards, accountability, and nuclear criticality safety significance; therefore, a technically defensible and well-documented holdup measurement program was needed. Appropriate standards were fabricated, measurement techniques were selected, and an aggressive schedule was followed. Early in the program, offsite experts reviewed the measurement program, and their recommendations were adopted. Contact and far-field methods were used for most measurements, but some process equipment required special attention. All holdup measurements were documented, and each report was subjected to internal peer review. Some measured values were checked against values obtained by other methods; agreement was generally good

A Model of Computation for Bit-Level Concurrent Computing and Programming: APEC

Science.gov (United States)

Ajiro, Takashi; Tsuchida, Kensei

A concurrent model of computation and a language based on the model for bit-level operation are useful for developing asynchronous and concurrent programs compositionally, which frequently use bit-level operations. Some examples are programs for video games, hardware emulation (including virtual machines), and signal processing. However, few models and languages are optimized and oriented to bit-level concurrent computation. We previously developed a visual programming language called A-BITS for bit-level concurrent programming. The language is based on a dataflow-like model that computes using processes that provide serial bit-level operations and FIFO buffers connected to them. It can express bit-level computation naturally and develop compositionally. We then devised a concurrent computation model called APEC (Asynchronous Program Elements Connection) for bit-level concurrent computation. This model enables precise and formal expression of the process of computation, and a notion of primitive program elements for controlling and operating can be expressed synthetically. Specifically, the model is based on a notion of uniform primitive processes, called primitives, that have three terminals and four ordered rules at most, as well as on bidirectional communication using vehicles called carriers. A new notion is that a carrier moving between two terminals can briefly express some kinds of computation such as synchronization and bidirectional communication. The model's properties make it most applicable to bit-level computation compositionally, since the uniform computation elements are enough to develop components that have practical functionality. Through future application of the model, our research may enable further research on a base model of fine-grain parallel computer architecture, since the model is suitable for expressing massive concurrency by a network of primitives.

Atmospheric Radiation Measurement Program Plan

International Nuclear Information System (INIS)

1990-02-01

In order to understand energy's role in anthropogenic global climate change, significant reliance is being placed on General Circulation Models (GCMs). A major goal of the Department is to foster the development of GCMs capable of predicting the timing and magnitude of greenhouse gas-induced global warming and the regional effects of such warming. DOE research has revealed that cloud radiative feedback is the single most important effect determining the magnitude of possible climate responses to human activity. However, cloud radiative forcing and feedbacks are not understood at the levels needed for reliable climate prediction. The Atmospheric Radiation Measurement (ARM) Program will contribute to the DOE goal by improving the treatment of cloud radiative forcing and feedbacks in GCMs. Two issues will be addressed: the radiation budget and its spectral dependence and the radiative and other properties of clouds. Understanding cloud properties and how to predict them is critical because cloud properties may very well change as climate changes. The experimental objective of the ARM Program is to characterize empirically the radiative processes in the Earth's atmosphere with improved resolution and accuracy. A key to this characterization is the effective treatment of cloud formation and cloud properties in GCMs. Through this characterization of radiative properties, it will be possible to understand both the forcing and feedback effects. GCM modelers will then be able to better identify the best approaches to improved parameterizations of radiative transfer effects. This is expected to greatly improve the accuracy of long-term, GCM predictions and the efficacy of those predictions at the important regional scale, as the research community and DOE attempt to understand the effects of greenhouse gas emissions on the Earth's climate. 153 refs., 24 figs., 6 tabs

Quality assurance program preparation - review of requirements and plant systems - selection of program levels

International Nuclear Information System (INIS)

Asmuss, G.

1980-01-01

The establishment and implementation for a practicable quality assurance program for a nuclear power plant demands a detailed background in the field of engineering, manufacturing, organization and quality assurance. It will be demonstrated with examples to define and control the achievement of quality related activities during the phases of design, procurement, manufactoring, commissioning and operation. In general the quality assurance program applies to all items, processes and services important to safety of nuclear power plant. The classification for safety related and non-safety related items and services demonstrate the levels of quality assurance requirements. The lecture gives an introduction of QA Program preparation under the following topics: -Basic criteria and international requirements - Interaction of QA activities - Modular and product oriented QA programs - Structuring of organization for the QA program - Identification of the main quality assurance functions and required actions - Quality Assurance Program documentation - Documentation of planning of activities - Control of program documents - Definitions. (orig./RW)

Measuring Satisfaction in the Program Manager, Procuring Contracting Officer Relationship

Science.gov (United States)

1997-12-01

Contracting Officer) and one of her customers (a U. S. Navy Program Manager ). From an examination of this relationship , the most appropriate criteria... Customer Satisfaction, Performance Measurement, Metrics, Contracting, Program Management 17. SECURITY CLASSIFICATION OF REPORT Unclassified...methodology for developing an instrument to measure the satisfaction of their customers , Navy Program Managers . The purpose of this thesis was to develop

The Level-1 Tile-Muon Trigger in the Tile Calorimeter upgrade program

International Nuclear Information System (INIS)

Ryzhov, A.

2016-01-01

The Tile Calorimeter (TileCal) is the central hadronic calorimeter of the ATLAS experiment at the Large Hadron Collider (LHC). TileCal provides highly-segmented energy measurements for incident particles. Information from TileCal's outermost radial layer can assist in muon tagging in the Level-1 Muon Trigger by rejecting fake muon triggers due to slow charged particles (typically protons) without degrading the efficiency of the trigger. The main activity of the Tile-Muon Trigger in the ATLAS Phase-0 upgrade program was to install and to activate the TileCal signal processor module for providing trigger inputs to the Level-1 Muon Trigger. This report describes the Tile-Muon Trigger, focusing on the new detector electronics such as the Tile Muon Digitizer Board (TMDB) that receives, digitizes and then provides the signal from eight TileCal modules to three Level-1 muon endcap Sector-Logic Boards.

Integrated Blanket Supplementary Feeding Program Reduces Levels of Stunting in Yenangyaung, Myanmar

International Nuclear Information System (INIS)

Aung, Thet; Baik, Diane

2014-01-01

Full text: BACKGROUND: Yenanchaung Township is the top ranked amongst the six poorest townships in the 25 townships comprising of Magway Division. There is food insecurity, poor transportation, high unemployment and migration rates widespread illiteracy, poor hygiene, and lack of health facilities. Along with food insecurity, high rates of malnutrition are found. In 2010, 39.5 percent of children under five years of age were found to be stunted, 18.1 percent wasted and 28.3 percent underweight. World Food Program (WFP) and World Vision Myanmar (WV) have been collaborating in response to the food insecurity situation in Yenangyaung since 2005 through food assistance interventions. However, in 2011, WV target villages started focusing on implementation of food activities apart from just food assistance; a more sustainable approach. Thus, the project is now focusing on maintaining the food security status of the targeted communities by strengthening the capacity in agriculture technique, alternative livelihood skills, and health/nutrition education. METHODS: This project is focused on food provision for all pregnant and lactating mothers and under 3 children according to the set criteria by WFP as well as nutrition education in the respective villages. Township health offices, village leaders and trained volunteers were used to carry out the activities of the project, including: health/nutrition education, food distribution, cooking demonstrations, integration of immunization and vitamin A supplementation, pre-/post-natal care, growth monitoring, counseling and referrals. The weight and MUAC of the children (n = 381) were taken every month, and height was measured every 3 months. Follow-up was conducted January 2012 to December 2012. Children were discharged from the program when they reached 3 years of age, regardless of the nutritional status. Thus, the data collected during the project was used to assess the impact of the program. RESULTS: No significant changes

Low-Level Plutonium Bioassay Measurements at the Lawrence Livermore National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Hamilton, T; Brown, T; Hickman, D; Marchetti, A; Williams, R; Kehl, S

2007-06-18

Plutonium-239 ({sup 239}Pu) and plutonium-240 ({sup 240}Pu) are important alpha emitting radionuclides contained in radioactive debris from nuclear weapons testing. {sup 239}Pu and {sup 240}Pu are long-lived radionuclides with half-lives of 24,400 years and 6580 years, respectively. Concerns over human exposure to plutonium stem from knowledge about the persistence of plutonium isotopes in the environment and the high relative effectiveness of alpha-radiation to cause potential harm to cells once incorporated into the human body. In vitro bioassay tests have been developed to assess uptakes of plutonium based on measured urinary excretion patterns and modeled metabolic behaviors of the absorbed radionuclides. Systemic plutonium absorbed by the deep lung or from the gastrointestinal tract after ingestion is either excreted or distributed to other organs, primarily to the liver and skeleton, where it is retained for biological half-times of around 20 and 50 years, respectively. Dose assessment and atoll rehabilitation programs in the Marshall Islands have historically given special consideration to residual concentrations of plutonium in the environment even though the predicted dose from inhalation and/or ingestion of plutonium accounts for less than 5% of the annual effective dose from exposure to fallout contamination. Scientists from the Lawrence Livermore National Laboratory (LLNL) have developed a state-of-the-art bioassay test to assess urinary excretion rates of plutonium from Marshallese populations. This new heavy-isotope measurement system is based on Accelerator Mass Spectrometry (AMS). The AMS system at LLNL far exceeds the standard measurement requirements established under the latest United States Department of Energy (DOE) regulation, 10CFR 835, for occupational monitoring of plutonium, and offers several advantages over classical as well as competing new technologies for low-level detection and measurement of plutonium isotopes. The United States

Market survey of level measurement equipment

International Nuclear Information System (INIS)

Anon.

1993-01-01

In a market survey of level measurement equipment from 42 manufacturers, which is based on different principles of measurement and which is used for different applications, the data of the various manufacturers is compiled. (orig./HP) [de

A measurement evaluation program to support nuclear material control and accountability measurements in Brazilian laboratories

International Nuclear Information System (INIS)

Dias, Fabio C.; Mason, Peter

2013-01-01

A measurement evaluation program (MEP) is one of a number of valuable tools that analytical chemists can use to ensure that the data produced in the laboratory are fit for their intended purpose and consistent with expected performance values at a given time. As such, participation in a MEP is an important indicator of the quality of analytical data, and is recognized as such by independent regulatory and/or accreditation bodies. With the intent to implement such a program in Brazil, in November 2012 the Nuclear Energy Commission of Brazil (CNEN), with support from the Department of Energy of the United States' (US-DOE International Safeguards and Engagement Program), decided to initiate a technical cooperation project aiming at organizing a Safeguards Measurement Evaluation Program (SMEP) for Brazilian facilities. The project, entitled Action Sheet 23, was formalized under the terms of the Agreement between the US-DOE and the CNEN concerning research and development in nuclear material control, accountancy, verification, physical protection, and advanced containment and surveillance technologies for International Safeguards Applications. The work, jointly performed by the CNEN's Safeguards Laboratory (LASAL) and the New Brunswick Laboratory (NBL), has the objective to strengthen the traceability of accountability measurements and ensure adequate quality of safeguards measurements for facilities within Brazil, utilizing test samples characterized and provided by NBL. Recommendations to participants included measurement frequency, number of results per sample and format for reporting results using ISO methods for calculating and expressing measurement uncertainties. In this paper, we discuss the main steps taken by CNEN and NBL aiming at implementing such a program and the expected results, in particular the impact of uncertainty estimation on the evaluation of performance of each participant laboratory. The program is considered by Brazilian safeguards authorities

A measurement evaluation program to support nuclear material control and accountability measurements in Brazilian laboratories

Energy Technology Data Exchange (ETDEWEB)

Dias, Fabio C., E-mail: fabio@ird.gov.br [Comissao Nacional de Energia Nuclear (CNEN-RJ), Rio de Janeiro, RJ (Brazil); Mason, Peter, E-mail: peter.mason@ch.doe.gov [New Brunswick Laboratory (DOE/NBL), Argonne, IL (United States)

2013-07-01

A measurement evaluation program (MEP) is one of a number of valuable tools that analytical chemists can use to ensure that the data produced in the laboratory are fit for their intended purpose and consistent with expected performance values at a given time. As such, participation in a MEP is an important indicator of the quality of analytical data, and is recognized as such by independent regulatory and/or accreditation bodies. With the intent to implement such a program in Brazil, in November 2012 the Nuclear Energy Commission of Brazil (CNEN), with support from the Department of Energy of the United States' (US-DOE International Safeguards and Engagement Program), decided to initiate a technical cooperation project aiming at organizing a Safeguards Measurement Evaluation Program (SMEP) for Brazilian facilities. The project, entitled Action Sheet 23, was formalized under the terms of the Agreement between the US-DOE and the CNEN concerning research and development in nuclear material control, accountancy, verification, physical protection, and advanced containment and surveillance technologies for International Safeguards Applications. The work, jointly performed by the CNEN's Safeguards Laboratory (LASAL) and the New Brunswick Laboratory (NBL), has the objective to strengthen the traceability of accountability measurements and ensure adequate quality of safeguards measurements for facilities within Brazil, utilizing test samples characterized and provided by NBL. Recommendations to participants included measurement frequency, number of results per sample and format for reporting results using ISO methods for calculating and expressing measurement uncertainties. In this paper, we discuss the main steps taken by CNEN and NBL aiming at implementing such a program and the expected results, in particular the impact of uncertainty estimation on the evaluation of performance of each participant laboratory. The program is considered by Brazilian safeguards

Radioactive Waste Management Research Program Plan for high-level waste: 1987

International Nuclear Information System (INIS)

1987-05-01

This plan will identify and resolve technical and scientific issues involved in the NRC's licensing and regulation of disposal systems intended to isolate high level hazardous radioactive wastes (HLW) from the human environment. The plan describes the program goals, discusses the research approach to be used, lays out peer review procedures, discusses the history and development of the high level radioactive waste problem and the research effort to date and describes study objectives and research programs in the areas of materials and engineering, hydrology and geochemistry, and compliance assessment and modeling. The plan also details the cooperative interactions with international waste management research programs. Proposed Earth Science Seismotectonic Research Program plan for radioactive waste facilities is appended

A Program to Generate a Particle Distribution from Emittance Measurements

CERN Document Server

Bouma, DS; Lallement, JB

2010-01-01

We have written a program to generate a particle distribution based on emittance measurements in x-x’ and y-y’. The accuracy of this program has been tested using real and constructed emittance measurements. Based on these tests, the distribution generated by the program can be used to accurately simulate the beam in multi-particle tracking codes, as an alternative to a Gaussian or uniform distribution.

Scholarly Productivity of School Psychology Faculty Members in Specialist-Level Programs: 2002-2011

Science.gov (United States)

Laurent, Jeff; Runia, Elizabeth

2016-01-01

The scholarly productivity of school psychology faculty members in specialist-level only programs was examined. Information was gathered from the School Psychology Program Information portion of the website for the National Association of School Psychologists. A total of 137 specialist-level only school psychology programs were identified.…

Promoting sustainability in quality improvement: an evaluation of a web-based continuing education program in blood pressure measurement.

Science.gov (United States)

Block, Lauren; Flynn, Sarah J; Cooper, Lisa A; Lentz, Caroline; Hull, Tammie; Dietz, Katherine B; Boonyasai, Romsai T

2018-01-10

The accuracy of blood pressure measurement is variable in office-based settings. Even when staff training programs are effective, knowledge and skills decay over time, supporting the need for ongoing staff training. We evaluated whether a web-based continuing education program in blood pressure measurement reinforced knowledge and skills among clinical staff and promoted sustainability of an existing quality improvement program. Medical assistants and nurses at six primary care clinics within a health system enrolled in a 30-min online educational program designed to refresh their knowledge of blood pressure measurement. A 20-question pre- and post-intervention survey addressed learners' knowledge and attitudes. Direct observation of blood pressure measurement technique before and after the intervention was performed. Differences in responses to pre- and post-module knowledge and attitudes questions and in observation data were analyzed using chi-square tests and simple logistic regression. All 88 clinical staff members participated in the program and completed the evaluation survey. Participants answered 80.6% of questions correctly before the module and 93.4% afterwards (p blood pressure measurement were high at baseline and did not improve significantly. Prior to the intervention, staff adhered to 9 of 18 elements of the recommended technique during at least 90% of observations. Following the program, staff was more likely to explain the protocol, provide a rest period, measure an average blood pressure, and record the average blood pressure, but less likely to measure blood pressure with the arm at heart level and use the right arm. We designed, implemented, and evaluated a web-based educational program to improve knowledge, skills, and attitudes in blood pressure measurement and use of an automated device among nurses and medical assistants in ambulatory care. The program reinforced knowledge related to recommended blood pressure measurement technique

UMTRA Project-Level Cost Reduction/Productivity Improvement Program manual

International Nuclear Information System (INIS)

1995-06-01

Mission of the Uranium Mill Tailings Remedial Action (UMTRA) Project Cost Reduction/Productivity Improvement Program (CR/PIP) is to contribute to the UMTRA Project's environmental restoration mission by providing the means to achieve and recognize continuous improvements and cost savings. This manual includes program definition, description of UMTRA project organizational responsibilities and interfaces with existing project functions, guidance to contractors, and definition of project-level functions

Towards identifying programming expertise with the use of physiological measures

DEFF Research Database (Denmark)

Kontogiorgos, Dimosthenis; Manikas, Konstantinos

2015-01-01

In this position paper we propose means of measuring programming expertise on novice and expert programmers. Our approach is to measure the cognitive load of programmers while they assess Java/Python code in accordance with their experience in programming. Our hypothesis is that expert programmers...

Measurement of water potential in low-level waste management

International Nuclear Information System (INIS)

Jones, T.L.; Gee, G.W.; Kirkham, R.R.; Gibson, D.D.

1982-08-01

The measurement of soil water is important to the shallow land burial of low-level waste. Soil water flow is the principle mechanism of radionuclide transport, allows the establishment of stabilizing vegetation and also governs the dissolution and release rates of the waste. This report focuses on the measurement of soil water potential and provides an evaluation of several field instruments that are available for use to monitor waste burial sites located in arid region soils. The theoretical concept of water potential is introduced and its relationship to water content and soil water flow is discussed. Next, four major areas of soils research are presented in terms of their dependence on the water potential concept. There are four basic types of sensors used to measure soil water potential. These are: (1) tensiometers; (2) soil psychrometers; (3) electrical resistance blocks; and (4) heat dissipation probes. Tensiometers are designed to measure the soil water potential directly by measuring the soil water pressure. Monitoring efforts at burial sites require measurements of soil water over long time periods. They also require measurements at key locations such as waste-soil interfaces and within any barrier system installed. Electrical resistance blocks are well suited for these types of measurements. The measurement of soil water potential can be a difficult task. There are several sensors commercially available; however, each has its own limitations. It is important to carefully select the appropriate sensor for the job. The accuracy, range, calibration, and stability of the sensor must be carefully considered. This study suggests that for waste management activities, the choice of sensor will be the tensiometer for precise soil characterization studies and the electrical resistance block for long term monitoring programs

FFTF reactor-characterization program: gamma-ray measurements and shield characterization

International Nuclear Information System (INIS)

Bunch, W.L.; Moore, F.S. Jr.

1983-02-01

A series of experiments is to be made during the acceptance test program of the Fast Flux Test Facility (FFTF) to measure the gamma ray characteristics of the Fast Test Reactor (FTR) and to establish the performance characteristics of the reactor shield. These measurements are a part of the FFTF Reactor Characterization Program (RCP). Detailed plans have been developed for these experiments. During the initial phase of the Characteristics Program, which will be carried out in the In-Reactor Thimble (IRT), both active and passive measurement methods will be employed to obtain as much information concerning the gamma ray environment as is practical. More limited active gamma ray measurements also will be made in the Vibration Open Test Assembly (VOTA)

The efficacy of stuttering measurement training: evaluating two training programs.

Science.gov (United States)

Bainbridge, Lauren A; Stavros, Candace; Ebrahimian, Mineh; Wang, Yuedong; Ingham, Roger J

2015-04-01

Two stuttering measurement training programs currently used for training clinicians were evaluated for their efficacy in improving the accuracy of total stuttering event counting. Four groups, each with 12 randomly allocated participants, completed a pretest-posttest design training study. They were evaluated by their counts of stuttering events on eight 3-min audiovisual speech samples from adults and children who stutter. Stuttering judgment training involved use of either the Stuttering Measurement System (SMS), Stuttering Measurement Assessment and Training (SMAAT) programs, or no training. To test for the reliability of any training effect, SMS training was repeated with the 4th group. Both SMS-trained groups produced approximately 34% improvement, significantly better than no training or the SMAAT program. The SMAAT program produced a mixed result. The SMS program was shown to produce a "medium" effect size improvement in the accuracy of stuttering event counts, and this improvement was almost perfectly replicated in a 2nd group. Half of the SMAAT judges produced a 36% improvement in accuracy, but the other half showed no improvement. Additional studies are needed to demonstrate the durability of the reported improvements, but these positive effects justify the importance of stuttering measurement training.

Potentiometric-level monitoring program: Mississippi and Louisiana. Annual status report for fiscal year 1984

International Nuclear Information System (INIS)

1986-07-01

Potentiometric-level data presented in this report were collected from October 1983 through September 1984 at 79 wells in Mississippi and Louisiana. These wells are located near Richton and Cypress Creek Domes in Mississippi and Vacherie Dome in Louisiana. Fourteen wells were added to the program during this period. Two of these wells were not measurable. Two wells previously unmeasurable were located and measured. One well was destroyed during military maneuvers in the area. Analysis of the data indicated minimal, if any, change in potentiometric levels during the past year in the Citronelle, Hattiesburg, Cockfield, Sparta, and Wilcox Formations in Mississippi. A continuing decline in potentiometric levels, ranging from 0.3 to 0.6 foot per year, occurred in the wells screened in the caprock at Richton and Cypress Creek Domes. The Catahoula Formation experienced a continuing decline in potentiometric levels of about 2 feet per year. Two wells in the Cook Mountain Formation showed a continuing rise in potentiometric levels ranging from 8 to 30 ft during the past fiscal year. Wells screened in the Austin Formation in Louisiana showed a fall in potentiometric levels of 2 to 3 ft over the past fiscal year. Other formations in Louisiana generally showed no change in potentiometric levels over the past year. 26 refs., 2 figs., 3 tabs

Individual and setting level predictors of the implementation of a skin cancer prevention program: a multilevel analysis

Directory of Open Access Journals (Sweden)

Brownson Ross C

2010-05-01

Full Text Available Abstract Background To achieve widespread cancer control, a better understanding is needed of the factors that contribute to successful implementation of effective skin cancer prevention interventions. This study assessed the relative contributions of individual- and setting-level characteristics to implementation of a widely disseminated skin cancer prevention program. Methods A multilevel analysis was conducted using data from the Pool Cool Diffusion Trial from 2004 and replicated with data from 2005. Implementation of Pool Cool by lifeguards was measured using a composite score (implementation variable, range 0 to 10 that assessed whether the lifeguard performed different components of the intervention. Predictors included lifeguard background characteristics, lifeguard sun protection-related attitudes and behaviors, pool characteristics, and enhanced (i.e., more technical assistance, tailored materials, and incentives are provided versus basic treatment group. Results The mean value of the implementation variable was 4 in both years (2004 and 2005; SD = 2 in 2004 and SD = 3 in 2005 indicating a moderate implementation for most lifeguards. Several individual-level (lifeguard characteristics and setting-level (pool characteristics and treatment group factors were found to be significantly associated with implementation of Pool Cool by lifeguards. All three lifeguard-level domains (lifeguard background characteristics, lifeguard sun protection-related attitudes and behaviors and six pool-level predictors (number of weekly pool visitors, intervention intensity, geographic latitude, pool location, sun safety and/or skin cancer prevention programs, and sun safety programs and policies were included in the final model. The most important predictors of implementation were the number of weekly pool visitors (inverse association and enhanced treatment group (positive association. That is, pools with fewer weekly visitors and pools in the enhanced

Sound level measurements using smartphone "apps": Useful or inaccurate?

Directory of Open Access Journals (Sweden)

Daniel R Nast

2014-01-01

Full Text Available Many recreational activities are accompanied by loud concurrent sounds and decisions regarding the hearing hazards associated with these activities depend on accurate sound measurements. Sound level meters (SLMs are designed for this purpose, but these are technical instruments that are not typically available in recreational settings and require training to use properly. Mobile technology has made such sound level measurements more feasible for even inexperienced users. Here, we assessed the accuracy of sound level measurements made using five mobile phone applications or "apps" on an Apple iPhone 4S, one of the most widely used mobile phones. Accuracy was assessed by comparing application-based measurements to measurements made using a calibrated SLM. Whereas most apps erred by reporting higher sound levels, one application measured levels within 5 dB of a calibrated SLM across all frequencies tested.

Implementing and measuring the level of laboratory service integration in a program setting in Nigeria.

Directory of Open Access Journals (Sweden)

Henry Mbah

Full Text Available The surge of donor funds to fight HIV&AIDS epidemic inadvertently resulted in the setup of laboratories as parallel structures to rapidly respond to the identified need. However these parallel structures are a threat to the existing fragile laboratory systems. Laboratory service integration is critical to remedy this situation. This paper describes an approach to quantitatively measure and track integration of HIV-related laboratory services into the mainstream laboratory services and highlight some key intervention steps taken, to enhance service integration.A quantitative before-and-after study conducted in 122 Family Health International (FHI360 supported health facilities across Nigeria. A minimum service package was identified including management structure; trainings; equipment utilization and maintenance; information, commodity and quality management for laboratory integration. A check list was used to assess facilities at baseline and 3 months follow-up. Level of integration was assessed on an ordinal scale (0 = no integration, 1 = partial integration, 2 = full integration for each service package. A composite score grading expressed as a percentage of total obtainable score of 14 was defined and used to classify facilities (≤ 80% FULL, 25% to 79% PARTIAL and <25% NO integration. Weaknesses were noted and addressed.We analyzed 9 (7.4% primary, 104 (85.2% secondary and 9 (7.4% tertiary level facilities. There were statistically significant differences in integration levels between baseline and 3 months follow-up period (p<0.01. Baseline median total integration score was 4 (IQR 3 to 5 compared to 7 (IQR 4 to 9 at 3 months follow-up (p = 0.000. Partial and fully integrated laboratory systems were 64 (52.5% and 0 (0.0% at baseline, compared to 100 (82.0% and 3 (2.4% respectively at 3 months follow-up (p = 0.000.This project showcases our novel approach to measure the status of each laboratory on the integration continuum.

Social network analysis of public health programs to measure partnership.

Science.gov (United States)

Schoen, Martin W; Moreland-Russell, Sarah; Prewitt, Kim; Carothers, Bobbi J

2014-12-01

In order to prevent chronic diseases, community-based programs are encouraged to take an ecological approach to public health promotion and involve many diverse partners. Little is known about measuring partnership in implementing public health strategies. We collected data from 23 Missouri communities in early 2012 that received funding from three separate programs to prevent obesity and/or reduce tobacco use. While all of these funding programs encourage partnership, only the Social Innovation for Missouri (SIM) program included a focus on building community capacity and enhancing collaboration. Social network analysis techniques were used to understand contact and collaboration networks in community organizations. Measurements of average degree, density, degree centralization, and betweenness centralization were calculated for each network. Because of the various sizes of the networks, we conducted comparative analyses with and without adjustment for network size. SIM programs had increased measurements of average degree for partner collaboration and larger networks. When controlling for network size, SIM groups had higher measures of network density and lower measures of degree centralization and betweenness centralization. SIM collaboration networks were more dense and less centralized, indicating increased partnership. The methods described in this paper can be used to compare partnership in community networks of various sizes. Further research is necessary to define causal mechanisms of partnership development and their relationship to public health outcomes. Copyright © 2014 Elsevier Ltd. All rights reserved.

The effect of a nutrition education program on the nutritional knowledge, hemoglobin levels, and nutritional status of Nicaraguan adolescent girls.

Science.gov (United States)

Moore, Jean Burley; Pawloski, Lisa; Rodriguez, Claudia; Lumbi, Laura; Ailinger, Rita

2009-01-01

The purpose of this study was to examine the effect of a community-based nutrition education program on the nutritional knowledge, hemoglobin levels, and nutritional status of Nicaraguan adolescent girls and the nutritional knowledge of their mothers. Self-care deficit nursing theory was used in this study. This longitudinal study used a mixed quantitative/qualitative design to study the effect of the nutrition education program. The nonprobability sample consisted of 182 adolescent girls and 67 of their mothers. The setting for the study was a community (barrio) in Managua, Nicaragua. INTERVENTION/MEASUREMENT: A team of nurse and nutrition researchers created the nutrition education program designed to improve girls' and mother's nutrition-related self-care operations. Data collection was carried out for 4 years for girls and 2 years for mothers in Managua, Nicaragua, using questionnaires, a HemoCue, and anthropometric measures. The findings of this study were that girls' and mothers' nutritional knowledge scores significantly improved in most cases after participation in the nutrition intervention program. Girls' hemoglobin levels did not significantly improve and their nutritional status findings were mixed. Girls and mothers described what dietary changes girls made and why.

Measuring Value in Internal Medicine Residency Training Hospitals Using Publicly Reported Measures.

Science.gov (United States)

Schickedanz, Adam; Gupta, Reshma; Arora, Vineet M; Braddock, Clarence H

2018-03-01

Graduate medical education (GME) lacks measures of resident preparation for high-quality, cost-conscious practice. The authors used publicly reported teaching hospital value measures to compare internal medicine residency programs on high-value care training and to validate these measures against program director perceptions of value. Program-level value training scores were constructed using Centers for Medicare & Medicaid Services Value-Based Purchasing (VBP) Program hospital quality and cost-efficiency data. Correlations with Association of Program Directors in Internal Medicine Annual Survey high-value care training measures were examined using logistic regression. For every point increase in program-level VBP score, residency directors were more likely to agree that GME programs have a responsibility to contain health care costs (adjusted odds ratio [aOR] 1.18, P = .04), their faculty model high-value care (aOR 1.07, P = .03), and residents are prepared to make high-value medical decisions (aOR 1.07, P = .09). Publicly reported clinical data offer valid measures of GME value training.

Status of beta measurement evaluation and upgrade program

International Nuclear Information System (INIS)

Swinth, K.L.

1986-01-01

In 1983, the US Department of Energy (DOE) initiated a program to evaluate and upgrade beta dosimetry capabilities at DOE and DOE-contractor facilities. The program has several elements which structure the development of improvements in beta measurement practices. In addition to Pacific Northwest Laboratory (PNL), universities, private corporations, and other DOE facilities are involved in the research efforts

Sampling plan design and analysis for a low level radioactive waste disposal program

International Nuclear Information System (INIS)

Hassig, N.L.; Wanless, J.W.

1989-01-01

Low-level wastes that are candidates for BRC (below regulatory concern) disposal must be subjected to an extensive monitoring program to insure the wastes meet (potential) bulk property and contamination concentration BRC criteria for disposal. This paper addresses the statistical implications of using various methods to verify BRC criteria. While surface and volumetric monitoring each have their advantages and disadvantages, a dual, sequential monitoring process is the preferred choice from a statistical reliability perspective. With dual monitoring, measurements on the contamination are verifiable, and sufficient to allow for a complete characterization of the wastes. As these characterizations become more reliable and stable, something less than 100% sampling may be possible for release of wastes for BRC disposal. This paper provides a survey of the issues involved in the selection of a monitoring and sampling program for the disposal of BRC wastes

Long-term high-level waste technology program

International Nuclear Information System (INIS)

1980-04-01

The Department of Energy (DOE) is conducting a comprehensive program to isolate all US nuclear wastes from the human environment. The DOE Office of Nuclear Energy - Waste (NEW) has full responsibility for managing the high-level wastes resulting from defense activities and additional responsiblity for providing the technology to manage existing commercial high-level wastes and any that may be generated in one of several alternative fuel cycles. Responsibilities of the Three Divisions of DOE-NEW are shown. This strategy document presents the research and development plan of the Division of Waste Products for long-term immobilization of the high-level radioactive wastes resulting from chemical processing of nuclear reactor fuels and targets. These high-level wastes contain more than 99% of the residual radionuclides produced in the fuels and targets during reactor operations. They include essentially all the fission products and most of the actinides that were not recovered for use

Measurement problem in PROGRAM UNIVERSE

International Nuclear Information System (INIS)

Noyes, H.P.; Gefwert, C.

1984-12-01

We present a discrete theory that meets the measurement problem in a new way. We generate a growing universe of bit strings, labeled by 2 127 + 136 strings organized by some representation of the closed, four level, combinatorial hierarchy, of bit-length N 139 greater than or equal to 139. The rest of the strings for each label, which grow in both length and number, are called addresses. The generating algorithm, called PROGRAM UNIVERSE, starts from a random choice between the two symbols ''0'' and ''1'' and grows (a) by discriminating between two randomly chosen strings and adjoining a novel result to the universe, or when the string so generated is not novel, by (b) adjoining a randomly chosen bit at the growing end of each string. We obtain, by appropriate definitions and interpretations, stable ''particles'' which satisfy the usual relativistic kinematics and quantized angular momentum without being localizable in a continuum space-time. The labeling scheme is congruent with the ''standard model'' of quarks and leptons with three generations, but for the problem at hand, the implementation of this aspect of the theory is unimportant. What matters most is that (a) these complicated ''particles'' have the periodicities familiar from relativistic ''deBroglie waves'' and resolve in a discrete way the ''wave-particle dualism'' and (b) can be ''touched'' by our discrete equivalent of ''soft photons'' in such a way as to follow, macroscopically, the usual Rutherford scattering trajectories with the associated bound states. Thus our theory could provide a discrete description of ''measurement'' in a way that allows no conceptual barrier between the ''micro'' and the ''macro'' worlds, if we are willing to base our physics on counting and exclude the ambiguities associated with the unobservable ''continuum''. 27 refs

A measurement system for large, complex software programs

Science.gov (United States)

Rone, Kyle Y.; Olson, Kitty M.; Davis, Nathan E.

1994-01-01

This paper describes measurement systems required to forecast, measure, and control activities for large, complex software development and support programs. Initial software cost and quality analysis provides the foundation for meaningful management decisions as a project evolves. In modeling the cost and quality of software systems, the relationship between the functionality, quality, cost, and schedule of the product must be considered. This explicit relationship is dictated by the criticality of the software being developed. This balance between cost and quality is a viable software engineering trade-off throughout the life cycle. Therefore, the ability to accurately estimate the cost and quality of software systems is essential to providing reliable software on time and within budget. Software cost models relate the product error rate to the percent of the project labor that is required for independent verification and validation. The criticality of the software determines which cost model is used to estimate the labor required to develop the software. Software quality models yield an expected error discovery rate based on the software size, criticality, software development environment, and the level of competence of the project and developers with respect to the processes being employed.

A workplace stretching program. Physiologic and perception measurements before and after participation.

Science.gov (United States)

Moore, T M

1998-12-01

The purpose of this study was to implement a primary prevention program in the workplace targeted to prevent muscle strains. Physiologic and perception measurements were taken before and after participation in a stretching program developed to improve flexibility through conditioning. A one group pre-test post-test design was used with 60 employees enrolled in a 36 session stretching program in the workplace. Flexibility was measured by a flexibility profile including the sit and reach test, bilateral body rotation measurements, and shoulder rotation measurements. A statistically significant increase was found in all flexibility measurements at the conclusion of the study for the participants as a total group. Perception, as measured by the Fox Physical Self Perception Profile, was statistically significant in relation to participants' perceptions of their body attractiveness, physical conditioning, and overall self worth at the program's conclusion. In addition, participants who completed the program had zero occurrences of musculoskeletal injuries during the 2 month period. The results of this study suggest that continued development and implementation of stretching programs in the workplace may benefit employees by increasing flexibility and potentially preventing injuries due to muscle strains. Stretching programs in the workplace also may improve components of employees' perceptions of their physical bodies.

Estimating the Population-Level Effectiveness of Vaccination Programs in the Netherlands.

NARCIS (Netherlands)

van Wijhe, Maarten; McDonald, Scott A; de Melker, Hester E; Postma, Maarten J; Wallinga, Jacco

There are few estimates of the effectiveness of long-standing vaccination programs in developed countries. To fill this gap, we investigate the direct and indirect effectiveness of childhood vaccination programs on mortality at the population level in the Netherlands.

Stability of multi-objective bi-level linear programming problems under fuzziness

Directory of Open Access Journals (Sweden)

Abo-Sinna Mahmoud A.

2013-01-01

Full Text Available This paper deals with multi-objective bi-level linear programming problems under fuzzy environment. In the proposed method, tentative solutions are obtained and evaluated by using the partial information on preference of the decision-makers at each level. The existing results concerning the qualitative analysis of some basic notions in parametric linear programming problems are reformulated to study the stability of multi-objective bi-level linear programming problems. An algorithm for obtaining any subset of the parametric space, which has the same corresponding Pareto optimal solution, is presented. Also, this paper established the model for the supply-demand interaction in the age of electronic commerce (EC. First of all, the study uses the individual objectives of both parties as the foundation of the supply-demand interaction. Subsequently, it divides the interaction, in the age of electronic commerce, into the following two classifications: (i Market transactions, with the primary focus on the supply demand relationship in the marketplace; and (ii Information service, with the primary focus on the provider and the user of information service. By applying the bi-level programming technique of interaction process, the study will develop an analytical process to explain how supply-demand interaction achieves a compromise or why the process fails. Finally, a numerical example of information service is provided for the sake of illustration.

Segregation Levels in Milwaukee Public Schools and the Milwaukee Voucher Program. School Choice Issues in the State

Science.gov (United States)

Forster, Greg

2006-01-01

This study compares segregation levels in Milwaukee public schools and in private schools participating in the Milwaukee voucher program. Using a segregation index that measures the difference between the percent of students in a school who are white and the percentage of school-age children in the greater metro area who are white, it finds that…

45 CFR 400.66 - Eligibility and payment levels in a publicly-administered RCA program.

Science.gov (United States)

2010-10-01

... 45 Public Welfare 2 2010-10-01 2010-10-01 false Eligibility and payment levels in a publicly... REFUGEE RESETTLEMENT PROGRAM Refugee Cash Assistance § 400.66 Eligibility and payment levels in a publicly-administered RCA program. (a) In administering a publicly-administered refugee cash assistance program, the...

Low-level radioactive waste research program plan

International Nuclear Information System (INIS)

O'Donnell, E.; Lambert, J.

1989-11-01

The Waste Management Branch, Division of Engineering, Office of Nuclear Regulatory Research, has developed a strategy for conducting research on issues of concern to the US Nuclear Regulatory Commission (NRC) in its efforts to ensure safe disposal of low-level radioactive waste (LLW). The resulting LLW research program plan provides an integrated framework for planning the LLW research program to ensure that the program and its products are responsive and timely for use in NRC's LLW regulatory program. The plan discusses technical and scientific issues and uncertainties associated with the disposal of LLW, presents programmatic goals and objectives for resolving them, establishes a long-term strategy for conducting the confirmatory and investigative research needed to meet these goals and objectives, and includes schedules and milestones for completing the research. Areas identified for investigation include waste form and other material concerns, failure mechanisms and radionuclide releases, engineered barrier performance, site characterization and monitoring, and performance assessment. The plan proposes projects that (1) analyze and test actual LLW and solidified LLW under laboratory and field conditions to determine leach rates and radionuclide releases, (2) examine the short- and long-term performance of concrete-enhanced LLW burial structures and high-integrity containers, and (3) attempt to predict water movement and contaminant transport through low permeability saturated media and unsaturated porous media. 4 figs., 3 tabs

Measurement of Heme Synthesis Levels in Mammalian Cells.

Science.gov (United States)

Hooda, Jagmohan; Alam, Maksudul; Zhang, Li

2015-07-09

Heme serves as the prosthetic group for a wide variety of proteins known as hemoproteins, such as hemoglobin, myoglobin and cytochromes. It is involved in various molecular and cellular processes such as gene transcription, translation, cell differentiation and cell proliferation. The biosynthesis levels of heme vary across different tissues and cell types and is altered in diseased conditions such as anemia, neuropathy and cancer. This technique uses [4-(14)C] 5-aminolevulinic acid ([(14)C] 5-ALA), one of the early precursors in the heme biosynthesis pathway to measure the levels of heme synthesis in mammalian cells. This assay involves incubation of cells with [(14)C] 5-ALA followed by extraction of heme and measurement of the radioactivity incorporated into heme. This procedure is accurate and quick. This method measures the relative levels of heme biosynthesis rather than the total heme content. To demonstrate the use of this technique the levels of heme biosynthesis were measured in several mammalian cell lines.

EPRI'S low-level waste management R ampersand D program

International Nuclear Information System (INIS)

Hornibrook, C.

1997-01-01

The immediate challenges facing every organization today are to improve its productivity and increase customer satisfaction. The Electric Power Research Institute (EPRI) responded to this challenge by broadening the scope of its low-level waste (LLW) management program. EPRI offered utilities on-site assistance in evaluating and optimizing their liquid- and solid-waste management programs. The goal is to identify open-quotes cheaper, better, and easierclose quotes solutions, which are documented in a series of reports. These provide step-by-step evaluation processes and straightforward implementation methods. Utility professionals are provided with the necessary technical information and justification for informed waste management decisions. The resulting average annual savings is consistently in excess of $700,000 per facility. The program continues to grow and serves as a model for a number of existing and emerging EPRI programs

Generation of Efficient High-Level Hardware Code from Dataflow Programs

OpenAIRE

Siret , Nicolas; Wipliez , Matthieu; Nezan , Jean François; Palumbo , Francesca

2012-01-01

High-level synthesis (HLS) aims at reducing the time-to-market by providing an automated design process that interprets and compiles high-level abstraction programs into hardware. However, HLS tools still face limitations regarding the performance of the generated code, due to the difficulties of compiling input imperative languages into efficient hardware code. Moreover the hardware code generated by the HLS tools is usually target-dependant and at a low level of abstraction (i.e. gate-level...

OSMOSE program : statistical review of oscillation measurements in the MINERVE reactor R1-UO2 configuration.

Energy Technology Data Exchange (ETDEWEB)

Stoven, G.; Klann, R.; Zhong, Z.; Nuclear Engineering Division

2007-08-28

The OSMOSE program is a collaboration on reactor physics experiments between the United States Department of Energy and the France Commissariat Energie Atomique. At the working level, it is a collaborative effort between the Argonne National Laboratory and the CEA Cadarache Research Center. The objective of this program is to measure very accurate integral reaction rates in representative spectra for the actinides important to future nuclear system designs, and to provide the experimental data for improving the basic nuclear data files. The main outcome of the OSMOSE measurement program will be an experimental database of reactivity-worth measurements in different neutron spectra for the heavy nuclides. This database can then be used as a benchmark to verify and validate reactor analysis codes. The OSMOSE program (Oscillation in Minerve of isotopes in Eupraxic Spectra) aims at improving neutronic predictions of advanced nuclear fuels through oscillation measurements in the MINERVE facility on samples containing the following separated actinides: {sup 232}Th, {sup 233}U, {sup 234}U, {sup 235}U, {sup 236}U, {sup 238}U, {sup 237}Np, {sup 238}Pu, {sup 239}Pu, {sup 240}Pu, {sup 241}Pu, {sup 242}Pu, {sup 241}Am, {sup 243}Am, {sup 244}Cm, and {sup 245}Cm. The first part of this report provides an overview of the experimental protocol and the typical processing of a series of experimental results which is currently performed at CEA-Cadarache. In the second part of the report, improvements to this technique are presented, as well as the program that was created to process oscillation measurement results from the MINERVE facility in the future.

Industrial level measurement techniques - a review

International Nuclear Information System (INIS)

Schaudel, D.E.

1984-01-01

The outlined methods of industrial level measurement technique are nowadays in current use. In correspondence with the technical evolution the mechanical techniques are mentioned first, followed by a description of the more modern electronic methods. These measurement methods comply especially to the requirements of computer aided process guiding systems, i.e. compatibility of signals, self-checking and reliability. (orig.) [de

Application of neutron backscatter techniques to level measurement problems

International Nuclear Information System (INIS)

Leonardi-Cattolica, A.M.; McMillan, D.H.; Telfer, A.; Griffin, L.H.; Hunt, R.H.

1982-01-01

We have designed and built portable level detectors and fixed level monitors based on neutron scattering and detection principles. The main components of these devices, which we call neutron backscatter gauges, are a neutron emitting radioisotope, a neutron detector, and a ratemeter. The gauge is a good detector for hydrogen but is much less sensitive to most other materials. This allows level measurements of hydrogen bearing materials, such as hydrocarbons, to be made through the walls of metal vessels. Measurements can be made conveniently through steel walls which are a few inches thick. We have used neutron backscatter gauges in a wide variety of level measurement applications encountered in the petrochemical industry. In a number of cases, the neutron techniques have proven to be superior to conventional level measurement methods, including gamma ray methods

Atmospheric Radiation Measurement Program plan

International Nuclear Information System (INIS)

1990-02-01

In order to understand energy's role in anthropogenic global climate change, significant reliance is being placed on General Circulation Models (GCMs). A major goal is to foster the development of GCMs capable of predicting the timing and magnitude of greenhouse gas-induced global warming and the regional effects of such warming. The Atmospheric Radiation Measurement (ARM) Program will contribute to the Department of Energy goal by improving the treatment of cloud radiative forcing and feedbacks in GCMs. Two issues will be addressed: the radiation budget and its spectral dependence and the radiative and other properties of clouds. The experimental objective of the ARM Program is to characterize empirically the radiative processes in the Earth's atmosphere with improved resolution and accuracy. A key to this characterization is the effective treatment of cloud formation and cloud properties in GCMs. Through this characterization of radiative properties, it will be possible to understand both the forcing and feedback effects. 19 refs., 4 figs., 2 tabs

Summary of neutron measurements for the Viking Program

International Nuclear Information System (INIS)

Anderson, M.E.

1975-01-01

The results of neutron measurements for 238 Pu-fueled, 683-W (thermal) capsules fabricated for the Viking Program (Mars Lander) are presented. These results include, for each capsule, the total neutron emission rate and neutron multiplication and, for one capsule, the neutron energy spectrum. A precision long counter was used for the neutron emission rate measurements and a single stilbene crystal for the neutron spectrum measurement. (U.S.)

Lifetime measurements of excited Co I levels

CERN Document Server

Klotz, W D; Gobel, L H

1977-01-01

In the region of 3500 AA the lifetimes of eight excited Cobalt I levels have been measured by means of the zero field level crossing method. The measured lifetimes belong to the odd configurations 3d/sup 7/4s4p and 3d/sup 8/4p and are of the accuracy of about 5%. The hyperfine structure of levels with I not=J has to be taken into account in evaluating lifetimes from level crossing data, because the nuclear spin of the natural isotope /sup 59/Co is I=7/2. Therefore the influence of the line profile of the exciting resonance lines on the lifetimes has been investigated. The results are compared with those of other authors. Furthermore absolute oscillator strengths were calculated with known branching ratios and a new absolute scale has been established. (23 refs).

Development of a package program for estimating ground level concentrations of radioactive gases

International Nuclear Information System (INIS)

Nilkamhang, W.

1986-01-01

A package program for estimating ground level concentration of radioactive gas from elevate release was develop for use on IBM P C microcomputer. The main program, GAMMA PLUME NT10, is based on the well known VALLEY MODEL which is a Fortran computer code intended for mainframe computers. Other two options were added, namely, calculation of radioactive gas ground level concentration in Ci/m 3 and dose equivalent rate in mren/hr. In addition, a menu program and editor program were developed to render the program easier to use since the option could be readily selected and the input data could be easily modified as required through the keyboard. The accuracy and reliability of the program is almost identical to the mainframe. Ground level concentration of radioactive radon gas due to ore program processing in the nuclear chemistry laboratory of the Department of Nuclear Technology was estimated. In processing radioactive ore at a rate of 2 kg/day, about 35 p Ci/s of radioactive gas was released from a 14 m stack. When meteorological data of Don Muang (average for 5 years 1978-1982) were used maximum ground level concentration and the dose equivalent rate were found to be 0.00094 p Ci/m 3 and 5.0 x 10 -10 mrem/hr respectively. The processing time required for the above problem was about 7 minutes for any case of source on IBM P C which was acceptable for a computer of this class

Dental Hygiene Entry-Level Program Administrators' Strategies for Overcoming Challenges of Distance Education

Science.gov (United States)

Buchanan, Bette A.

2009-01-01

The use of distance education by entry-level dental hygiene programs is increasing. The focus of this study was to determine the number of entry-level dental hygiene program administrators with experience developing and/or maintaining dental hygiene education by distance, the challenges encountered, and the strategies used to overcome the…

Wireless Fluid-Level Measurement System Equips Boat Owners

Science.gov (United States)

2008-01-01

While developing a measurement acquisition system to be used to retrofit aging aircraft with vehicle health monitoring capabilities, Langley Research Center developed an innovative wireless fluid-level measurement system. The NASA technology was of interest to Tidewater Sensors LLC, of Newport News, Virginia, because of its many advantages over conventional fuel management systems, including its ability to provide an accurate measurement of volume while a boat is experiencing any rocking motion due to waves or people moving about on the boat. These advantages led the company to license this novel fluid-level measurement system from NASA for marine applications.

A nonlinear bi-level programming approach for product portfolio management.

Science.gov (United States)

Ma, Shuang

2016-01-01

Product portfolio management (PPM) is a critical decision-making for companies across various industries in today's competitive environment. Traditional studies on PPM problem have been motivated toward engineering feasibilities and marketing which relatively pay less attention to other competitors' actions and the competitive relations, especially in mathematical optimization domain. The key challenge lies in that how to construct a mathematical optimization model to describe this Stackelberg game-based leader-follower PPM problem and the competitive relations between them. The primary work of this paper is the representation of a decision framework and the optimization model to leverage the PPM problem of leader and follower. A nonlinear, integer bi-level programming model is developed based on the decision framework. Furthermore, a bi-level nested genetic algorithm is put forward to solve this nonlinear bi-level programming model for leader-follower PPM problem. A case study of notebook computer product portfolio optimization is reported. Results and analyses reveal that the leader-follower bi-level optimization model is robust and can empower product portfolio optimization.

The Effectiveness of Social Skills Training Program via Peer Tutoring on Aggression Level

Directory of Open Access Journals (Sweden)

İsmail YELPAZE

2015-12-01

Full Text Available The purpose of this study was to investigate the effectiveness of social skills intervention program via peer tutoring on aggression level of secondary school students. The study was a semi-experimental model using experimental group with pre and post-tests. Eleven (eighth class students were selected to have skills for being peer helper. The population of this research consisted 56 secondary school students at Kahramanmaraş. In order to evaluate aggression level of students, Aggression Scale developed by Tuzgöl (1998 was used. . Additionally, a Personal Information Sheet developed by the researcher was used to record certain demographic variables. Researcher applied social skills invention program to 11 students (peer helpers for eight weeks. Later, peer helpers applied intervention program to selected 56 students as well. After application, last-test was applied to selected 56 students, again. To analyze the data collected, SPSS 15 for computer was used. Results of the research revealed that the social skill program via peer helping (peer guidance considerably decreased the level of aggression of students at secondary school students. Students’ aggression level differentiated according to their sex, but not their class levels. Results were discussed in the light of literature

Exploring the Unique Features of a First Nations Graduate-Level Social Work Program

Directory of Open Access Journals (Sweden)

Ralph C. Bodor

2015-03-01

Full Text Available Recently, a one-time cohort of graduate-level social work students completed a unique MSW program. The program was delivered in partnership between the Faculty of Social Work, University of Calgary and Blue Quills First Nations College and, of the twenty four graduates; twenty-one were of First Nations or Me´tis ancestry. The program honored traditional knowledge and ways of learning combined with a critical analysis of Western perspectives of social work knowledge. Strong fiscal resources enabled the program to establish a formal support network for the students and to support the development of Indigenous curriculum and programming that encouraged success for the students. The program was fundamentally different than urban on-campus programs while still maintaining graduate level accreditation requirements. This analysis of the program required the use of Indigenous Research Methodology to collect and create an understanding of the program. Instructors commented on the centered, empowered, balanced, and congruent students. The formal and informal, concrete and invisible supports to the students ensured the success of this program and this cohort of students. As one student commented, the program started in ceremony, ended in ceremony, and could not fail within the context ceremony.

Experiences with High-Level Programming Directives for Porting Applications to GPUs

International Nuclear Information System (INIS)

Ding, Wei; Chapman, Barbara; Sankaran, Ramanan; Graham, Richard L.

2012-01-01

HPC systems now exploit GPUs within their compute nodes to accelerate program performance. As a result, high-end application development has become extremely complex at the node level. In addition to restructuring the node code to exploit the cores and specialized devices, the programmer may need to choose a programming model such as OpenMP or CPU threads in conjunction with an accelerator programming model to share and manage the difference node resources. This comes at a time when programmer productivity and the ability to produce portable code has been recognized as a major concern. In order to offset the high development cost of creating CUDA or OpenCL kernels, directives have been proposed for programming accelerator devices, but their implications are not well known. In this paper, we evaluate the state of the art accelerator directives to program several applications kernels, explore transformations to achieve good performance, and examine the expressiveness and performance penalty of using high-level directives versus CUDA. We also compare our results to OpenMP implementations to understand the benefits of running the kernels in the accelerator versus CPU cores.

The Level-1 Tile-Muon Trigger in the Tile Calorimeter Upgrade Program

CERN Document Server

Ryzhov, Andrey; The ATLAS collaboration

2016-01-01

The Tile Calorimeter (TileCal) is the central hadronic calorimeter of the ATLAS experiment at the Large Hadron Collider (LHC). The TileCal provides highly-segmented energy measurements for incident particles. Information from TileCal's last radial layer can assist in muon tagging using Level-1 muon trigger. It can help in the rejection of fake muon triggers arising from background radiation (slow charged particles - protons) without degrading the efficiency of the trigger. The TileCal main activity for Phase-0 upgrade ATLAS program (2013-2014) was the activation of the TileCal third layer signal for assisting the muon trigger at 1.0<|η|<1.3 (Tile-Muon Trigger). This report describes the Tile-Muon Trigger at TileCal upgrade activities, focusing on the new on-detector electronics such as Tile Muon Digitizer Board (TMDB) to provide (receive and digitize) the signal from eight TileCal modules to three Level-1 muon endcap sector logic blocks.

Hydrocarbon emissions from gas engine CHP-units. 2011 measurement program

Energy Technology Data Exchange (ETDEWEB)

Van Dijk, G.H.J. [KEMA, Arnhem (Netherlands)

2012-06-15

In December 2009, the Ministry of Infrastructure and Environment (IandM) issued the Decree on Emission Limits for Middle Sized Combustion Installations (BEMS). This decree imposes a first-time emission limit value (ELV) of 1500 mg C/m{sup 3}{sub o} at 3% O{sub 2} for hydrocarbons emitted by gas engines. IandM used the findings of two hydrocarbon emission measurement programs, executed in 2007 and 2009, as a guideline for this initial ELV. The programs did reveal substantial variation in the hydrocarbon emissions of the gas engines tested. This variation, and especially the uncertainty as to the role of engine and/or other parameters causing such variation, was felt to hamper further policy development. IandM therefore commissioned KEMA to perform follow-up measurements on ten gas engine CHP-units in 2011. Aim of this 2011 program is to assess hydrocarbon emission variation in relation to engine parameters and process conditions including maintenance status, and to atmospheric conditions. The 2011 program comprised two identical measurement sessions, one in spring and one in winter.

Combining landscape-level conservation planning and biodiversity offset programs: a case study.

Science.gov (United States)

Underwood, Jared G

2011-01-01

Habitat loss is a major factor in the endangerment and extinction of species around the world. One promising strategy to balance continued habitat loss and biodiversity conservation is that of biodiversity offsets. However, a major concern with offset programs is their consistency with landscape-level conservation goals. While merging offset policies and landscape-level conservation planning is thought to provide advantages over a traditional disconnected approach, few such landscape-level conservation-offset plans have been designed and implemented, so the effectiveness of such a strategy remains uncertain. In this study, we quantitatively assess the conservation impact of combining landscape-level conservation planning and biodiversity offset programs by comparing regions of San Diego County, USA with the combined approach to regions with only an offset program. This comparison is generally very difficult due to a variety of complicating factors. We overcome these complications and quantify the benefits to rare and threatened species of implementing a combined approach by assessing the amount of each species' predicted distribution, and the number of documented locations, conserved in comparison to the same metric for areas with an offset policy alone. We found that adoption of the combined approach has increased conservation for many rare species, often 5-10 times more than in the comparison area, and that conservation has been focused in the areas most important for these species. The level of conservation achieved reduces uncertainty that these species will persist in the region into the future. This San Diego County example demonstrates the potential benefits of combining landscape-level conservation planning and biodiversity offset programs.

LOFT liquid level transducer application techniques and measurement uncertainty

International Nuclear Information System (INIS)

Batt, D.L.; Biladeau, G.L.; Goodrich, L.D.; Nightingale, C.M.

1979-01-01

A conductivity sensitive liquid level transducer (LLT) has been designed and used successfully for determining whether steam or water is present in the Loss-of-Fluid Tests (LOFT) performed by EG and G Idaho, Inc., at the Idaho National Engineering Laboratory. The presence of steam or water is determined by establishing a discriminator level which is set manually. A computer program establishes the presence or absence of water for each data point taken. In addition to liquid level, the LLT is used for reactor vessel mass and volume calculations. The uncertainty in the liquid level is essentially the spacing of the LLT electrodes

USCEA/NIST measurement assurance programs for the radiopharmaceutical and nuclear power industries

International Nuclear Information System (INIS)

Golas, D.B.

1993-01-01

In cooperation with the U.S. Council for Energy Awareness (USCEA), the National Institute of Standards and Technology (NIST) supervises and administers two measurement assurance programs for radioactivity measurement traceability. One, in existence since the mid 1970s, provides traceability to suppliers of radiochemicals and radiopharmaceuticals, dose calibrators, and nuclear pharmacy services. The second program, begun in 1987, provides traceability to the nuclear power industry for utilities, source suppliers, and service laboratories. Each program is described, and the results of measurements of samples of known, but undisclosed activity, prepared at NIST and measured by the participants are presented

USCEA/NIST measurement assurance programs for the radiopharmaceutical and nuclear power industries

Energy Technology Data Exchange (ETDEWEB)

Golas, D.B. [Council for Energy Awareness, Washington, DC (United States)

1993-12-31

In cooperation with the U.S. Council for Energy Awareness (USCEA), the National Institute of Standards and Technology (NIST) supervises and administers two measurement assurance programs for radioactivity measurement traceability. One, in existence since the mid 1970s, provides traceability to suppliers of radiochemicals and radiopharmaceuticals, dose calibrators, and nuclear pharmacy services. The second program, begun in 1987, provides traceability to the nuclear power industry for utilities, source suppliers, and service laboratories. Each program is described, and the results of measurements of samples of known, but undisclosed activity, prepared at NIST and measured by the participants are presented.

Community-level Moderators of a School-Based Childhood Sexual Assault Prevention Program

OpenAIRE

Morris, Matthew C.; Kouros, Chrystyna D.; Janecek, Kim; Freeman, Rachel; Mielock, Alyssa; Garber, Judy

2016-01-01

Childhood sexual abuse (CSA) is highly prevalent and associated with a wide variety of negative mental and physical health outcomes. School-based CSA education and prevention programs have shown promise, but it is unclear to what extent community-level characteristics are related to their effectiveness. The present cluster randomized controlled trial evaluated community-level moderators of the Safe@Last program compared to a waitlist control condition. Knowledge gains from pre- to post-interv...

Proceedings of the Third Annual Information Meeting DOE Low-Level Waste-Management Program

Energy Technology Data Exchange (ETDEWEB)

Large, D.E.; Lowrie, R.S.; Stratton, L.E.; Jacobs, D.G. (comps.)

1981-12-01

The Third Annual Participants Information Meeting of the Low-Level Waste Management Program was held in New Orleans, Louisiana, November 4-6, 1981 The specific purpose was to bring together appropriate representatives of industry, USNRC, program management, participating field offices, and contractors to: (1) exchange information and analyze program needs, and (2) involve participants in planning, developing and implementing technology for low-level waste management. One hundred seven registrants participated in the meeting. Presentation and workshop findings are included in these proceedings under the following headings: low-level waste activities; waste treatment; shallow land burial; remedial action; greater confinement; ORNL reports; panel workshops; and summary. Forty-six papers have been abstracted and indexed for the data base.

Proceedings of the Third Annual Information Meeting DOE Low-Level Waste-Management Program

International Nuclear Information System (INIS)

Large, D.E.; Lowrie, R.S.; Stratton, L.E.; Jacobs, D.G.

1981-12-01

The Third Annual Participants Information Meeting of the Low-Level Waste Management Program was held in New Orleans, Louisiana, November 4-6, 1981 The specific purpose was to bring together appropriate representatives of industry, USNRC, program management, participating field offices, and contractors to: (1) exchange information and analyze program needs, and (2) involve participants in planning, developing and implementing technology for low-level waste management. One hundred seven registrants participated in the meeting. Presentation and workshop findings are included in these proceedings under the following headings: low-level waste activities; waste treatment; shallow land burial; remedial action; greater confinement; ORNL reports; panel workshops; and summary. Forty-six papers have been abstracted and indexed for the data base

Evaluation of a method to measure long term cortisol levels.

Science.gov (United States)

Manenschijn, Laura; Koper, Jan W; Lamberts, Steven W J; van Rossum, Elisabeth F C

2011-01-01

Elevated levels of cortisol are known to induce various symptoms and diseases, e.g. abdominal obesity, type 2 diabetes, osteoporosis and cardiovascular disease. Measuring serum, saliva and urine cortisol is limited to one time point. Measurement of cortisol in scalp hair is a recently developed method to measure long term cortisol levels. The aim of this study was to investigate whether hair cortisol is a feasible parameter to measure cortisol exposure. We collected hair samples of 195 healthy individuals, 9 hypercortisolemic and one hypocortisolemic patient and measured hair cortisol levels. Cortisol was extracted from scalp hair using methanol and cortisol levels were measured using a salivary ELISA kit. Measurement of waist and hip circumferences and blood pressure was performed in 46 healthy subjects. We found a positive correlation between hair cortisol and both waist circumference (r=0.392, p=0.007) and waist-to-hip ratio (WHR) (r=0.425, p=0.003). No correlations were found between hair cortisol levels and BMI, blood pressure or age. There was no decline in cortisol levels in six consecutive hair segments. Hair cortisol levels were elevated in patients with known hypercortisolism (pcortisol was positively correlated with WHR, suggesting that hair cortisol reflects cortisol exposure at tissue level, which was also supported by elevated hair cortisol levels in hypercortisolemic patients and concordance between hair cortisol levels and clinical disease course. Cortisol levels in hair are slightly influenced by hair treatment but not by natural hair colour, use of hair products, gender or age. Copyright © 2011 Elsevier Inc. All rights reserved.

Survey and Design of Master Level Programs in Disaster Risk Management

DEFF Research Database (Denmark)

Nielsen, Linda; Nielsen, Michael Havbro Faber

2017-01-01

This paper summarizes the results obtained from performing a semistructured search to identify the number of Disaster Risk Management (DRM) master level programs (MPs) offered in the western European and Scandinavian countries. The purpose of this activity is to map the external environment...... in which the EU Erasmus project Knowledge for Resilient Society (K-FORCE) future MP in DRM will be operating as well as to evaluate what program organization and curriculum content the new program preferrably should incorporate....

41 CFR 102-192.150 - What are your general responsibilities as a program level mail manager?

Science.gov (United States)

2010-07-01

... responsibilities as a program level mail manager? 102-192.150 Section 102-192.150 Public Contracts and Property... general responsibilities as a program level mail manager? Your responsibilities at the program level include— (a) Working closely with the agency mail manager and mail center managers who handle significant...

Low-level rf system for the AGS Light Ion Program

International Nuclear Information System (INIS)

Kovarik, V.; Ahrens, L.; Barton, D.S.; Frankel, R.; Otis, A.; Pope, D.; Pritsker, M.; Raka, E.; Warkentien, R.

1987-01-01

The new low level rf system for the light ion acceleration program features direct digital control of a phase continuous rf synthesizer clocked by finite changes in the B field. The system, its operation and testing are described. The system covers the complete rf frequency range and switches over from single cavity acceleration to multiple cavity acceleration with no beam loss. It also switches from the programmed drive to the normal bootstrap system

The Canadian program for management of spent fuel and high level wastes

International Nuclear Information System (INIS)

Barnes, R.W.; Mayman, S.A.

A brief history and description of the nuclear power program in Canada is given. Schedules and programs are described for storing spent fuel in station fuel bays, centralized water pool storage facilities, concrete canisters, convection vaults, and rock or salt formations. High-level wastes will be retrievable initially, therefore the focus is on storage in mined cavities. The methods developed for high-level waste storage/disposal will ideally be flexible enough to accommodate spent fuel. (E.C.B.)

Precise mean sea level measurements using the Global Positioning System

Science.gov (United States)

Kelecy, Thomas M.; Born, George H.; Parke, Michael E.; Rocken, Christian

1994-01-01

This paper describes the results of a sea level measurement test conducted off La Jolla, California, in November of 1991. The purpose of this test was to determine accurate sea level measurements using a Global Positioning System (GPS) equipped buoy. These measurements were intended to be used as the sea level component for calibration of the ERS 1 satellite altimeter. Measurements were collected on November 25 and 28 when the ERS 1 satellite overflew the calibration area. Two different types of buoys were used. A waverider design was used on November 25 and a spar design on November 28. This provided the opportunity to examine how dynamic effects of the measurement platform might affect the sea level accuracy. The two buoys were deployed at locations approximately 1.2 km apart and about 15 km west of a reference GPS receiver located on the rooftop of the Institute of Geophysics and Planetary Physics at the Scripps Institute of Oceanography. GPS solutions were computed for 45 minutes on each day and used to produce two sea level time series. An estimate of the mean sea level at both locations was computed by subtracting tide gage data collected at the Scripps Pier from the GPS-determined sea level measurements and then filtering out the high-frequency components due to waves and buoy dynamics. In both cases the GPS estimate differed from Rapp's mean altimetric surface by 0.06 m. Thus, the gradient in the GPS measurements matched the gradient in Rapp's surface. These results suggest that accurate sea level can be determined using GPS on widely differing platforms as long as care is taken to determine the height of the GPS antenna phase center above water level. Application areas include measurement of absolute sea level, of temporal variations in sea level, and of sea level gradients (dominantly the geoid). Specific applications would include ocean altimeter calibration, monitoring of sea level in remote regions, and regional experiments requiring spatial and

The possible direct use of satellite radiance measurements by the Atmospheric Radiation Measurement Program

International Nuclear Information System (INIS)

1993-03-01

The Atmospheric Radiation Measurement (ARM) Program is a major research program initiated by the Department of Energy to improve our understanding of radiative and cloud processes critical to predicting the Earth's climate and its changes. Central to this concept is the use of four to six intensively instrumented sites for long-term study and characterization of the processes of interest. The instrumentation suites will include ground-based, high-accuracy radiometers for measuring the short and longwave surface flux, as well as an extensive set of ground-and air-based instrumentation for characterizing the intervening atmospheric column. Satellite-based measurements are expected to play a very important role in providing top-of-the-atmosphere measurements. In this study, we examine the possibility of comparing ARM outputs directly with satellite measurements, thereby ensuring the independence of these two important data sets. Thus we focused on what do satellites really measure and how well do they measure it. On what can we do about the general lack of adequate visible channel calibration. On what is the best way for ARM to obtain near-real-time access to this unprocessed data. And on what is the optimum way for ARM to make use of satellite data

Optimal Design of Measurement Programs for the Parameter Identification of Dynamic Systems

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Sørensen, John Dalsgaard; Brincker, Rune

The design of measurement programs devoted to parameter identification of structural dynamic systems is considered. The design problem is formulated as an optimization problem to minimize the total expected cost that is the cost of failure and the cost of the measurement program. All...... the calculations are based on a priori knowledge and engineering judgement. One of the contribution of the approach is that the optimal number of sensors can be estimated. This is shown in a numerical example where the proposed approach is demonstrated. The example is concerned with design of a measurement program...

Optimal Design of Measurement Programs for the Parameter Identification of Dynamic Systems

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Sørensen, John Dalsgaard; Brincker, Rune

The design of a measured program devoted to parameter identification of structural dynamic systems is considered, the design problem is formulated as an optimization problem due to minimize the total expected cost of the measurement program. All the calculations are based on a priori knowledge...... and engineering judgement. One of the contribution of the approach is that the optimal nmber of sensors can be estimated. This is sown in an numerical example where the proposed approach is demonstrated. The example is concerned with design of a measurement program for estimating the modal damping parameters...

Stakeholders' perceptions on competency and assessment program of entry-level pharmacists in developing countries.

Science.gov (United States)

Asante, Isaac; Andoh, Irene; Muijtjens, Arno M M; Donkers, Jeroen

2017-05-01

To assess the stakeholders' perceptions on the competency of entry-level pharmacists and the use of written licensure examination as the primary assessment for licensure decisions on entry-level pharmacists who have completed the Pharmacy Internship Program 1 (PIP) in developing countries. A cross-sectional survey was conducted among stakeholders in which they completed a web-based 21-item pre-tested questionnaire to determine their views regarding the competency outcomes and assessment program for entry-level pharmacist. The stakeholders rated the entry-level pharmacists to possess all competencies except research skills. Stakeholders suggested improvement of the program by defining the competency framework and training preceptors. However, stakeholders disagree on using written examination as the primary assessment for licensure decision and suggested the incorporation of other performance-based assessments like preceptor's assessment reports. Stakeholders are uncertain on entry-level pharmacists in developing countries possessing adequate research competencies and think their assessment program for licensure need more than written examination to assess all required competencies. Copyright © 2017 Elsevier Inc. All rights reserved.

An automatic controlled apparatus of target chamber for atomic spectra and level lifetime measurements

International Nuclear Information System (INIS)

Zhao Mengchun; Yang Zhihu

1998-01-01

An automatically controlled apparatus of target chamber was made to measure spectra of the excited atoms and lifetime of the excited levels. The hardware is composed of nine parts including a computer and a step-motor, while the software consists of three branch programs. The maximum movable distance of target position is 65 cm with a step-length of 8.3 μm and a precision of +- 18 μm per 2 mm. On account of simple structure and double protection, the apparatus exhibits flexibility and reliability in years service

Towards Implementation of a Generalized Architecture for High-Level Quantum Programming Language

Science.gov (United States)

Ameen, El-Mahdy M.; Ali, Hesham A.; Salem, Mofreh M.; Badawy, Mahmoud

2017-08-01

This paper investigates a novel architecture to the problem of quantum computer programming. A generalized architecture for a high-level quantum programming language has been proposed. Therefore, the programming evolution from the complicated quantum-based programming to the high-level quantum independent programming will be achieved. The proposed architecture receives the high-level source code and, automatically transforms it into the equivalent quantum representation. This architecture involves two layers which are the programmer layer and the compilation layer. These layers have been implemented in the state of the art of three main stages; pre-classification, classification, and post-classification stages respectively. The basic building block of each stage has been divided into subsequent phases. Each phase has been implemented to perform the required transformations from one representation to another. A verification process was exposed using a case study to investigate the ability of the compiler to perform all transformation processes. Experimental results showed that the efficacy of the proposed compiler achieves a correspondence correlation coefficient about R ≈ 1 between outputs and the targets. Also, an obvious achievement has been utilized with respect to the consumed time in the optimization process compared to other techniques. In the online optimization process, the consumed time has increased exponentially against the amount of accuracy needed. However, in the proposed offline optimization process has increased gradually.

Hanford long-term high-level waste management program overview

International Nuclear Information System (INIS)

Reep, I.E.

1978-05-01

The objective is the long-term disposition of the defense high-level radioactive waste which will remain upon completion of the interim waste management program in the mid-1980s, plus any additional high-level defense waste resulting from the future operation of N Reactor and the Purex Plant. The high-level radioactive waste which will exist in the mid-1980s and is addressed by this plan consists of approximately 3,300,000 ft 3 of damp salt cake stored in single-shell and double-shell waste tanks, 1,500,000 ft 3 of damp sludge stored in single-shell and double-shell waste tanks, 11,000,000 gallons of residual liquor stored in double-shell waste tanks, 3,000,000 gallons of liquid wastes stored in double-shell waste tanks awaiting solidification, and 2,900 capsules of 90 SR and 137 Cs compounds stored in water basins. Final quantities of waste may be 5 to 10% greater, depending on the future operation of N Reactor and the Purex Plant and the application of waste treatment techniques currently under study to reduce the inventory of residual liquor. In this report, the high-level radioactive waste addressed by this plan is briefly described, the major alternatives and strategies for long-term waste management are discussed, and a description of the long-term high-level waste management program is presented. Separate plans are being prepared for the long-term management of radioactive wastes which exist in other forms. 14 figures

CMS High Level Trigger Timing Measurements

International Nuclear Information System (INIS)

Richardson, Clint

2015-01-01

The two-level trigger system employed by CMS consists of the Level 1 (L1) Trigger, which is implemented using custom-built electronics, and the High Level Trigger (HLT), a farm of commercial CPUs running a streamlined version of the offline CMS reconstruction software. The operational L1 output rate of 100 kHz, together with the number of CPUs in the HLT farm, imposes a fundamental constraint on the amount of time available for the HLT to process events. Exceeding this limit impacts the experiment's ability to collect data efficiently. Hence, there is a critical need to characterize the performance of the HLT farm as well as the algorithms run prior to start up in order to ensure optimal data taking. Additional complications arise from the fact that the HLT farm consists of multiple generations of hardware and there can be subtleties in machine performance. We present our methods of measuring the timing performance of the CMS HLT, including the challenges of making such measurements. Results for the performance of various Intel Xeon architectures from 2009-2014 and different data taking scenarios are also presented. (paper)

Early in-situ measurements program for the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Wowak, W.E.

1979-06-01

The technical basis and description of measurements for the early in-situ measurements program at the WIPP are described and a proposed organizational structure is presented. Measurements are needed for verification of design predictions and also for a prelude to the main experiment program. The design verification measurements will be concentrated in the first shaft and the underground support and access areas. Early experiments will be concentrated in the test drifts on the storage horizons. Recommendations are made to DOE for appropriate division of responsibility among Bechtel, the technical support contractor, the instrumentation contractor, and Sandia

Students' Desired and Experienced Levels of Connectivity to an Asynchronous, Online, Distance Degree Program

Science.gov (United States)

Schroeder, Shawnda; Baker, Mary; Terras, Katherine; Mahar, Patti; Chiasson, Kari

2016-01-01

This study examined graduate students' desired and experienced levels of connectivity in an online, asynchronous distance degree program. Connectivity was conceptualized as the students' feelings of community and involvement, not their level of access to the Internet. Graduate students enrolled in a distance degree program were surveyed on both…

Program evaluation: Weatherization Residential Assistance Partnership (WRAP) Program

Energy Technology Data Exchange (ETDEWEB)

1991-12-01

The Connecticut low income weatherization program was developed in response to a 1987 rate docket order from the Connecticut Department of Public Utility Control (DPUC) to Connecticut Light Power Co., an operating subsidiary of Northeast Utilities (NU). (Throughout this report, NU is referred to as the operator of the program.) This program, known as the Weatherization Residential Assistance Partnership, or WRAP, was configured utilizing input from a collaborative group of interested parties to the docket. It was agreed that this program would be put forth by the electric utility, but would not ignore oil and gas savings (thus, it was to be fuel- blind''). The allocated cost of conservation services for each fuel source, however, should be cost effective. It was to be offered to those utility customers at or below 200 percent of the federal poverty levels, and provide a wide array of energy saving measures directed toward heating, water heating and lighting. It was felt by the collaborative group that this program would raise the level of expenditures per participant for weatherization services provided by the state, and by linking to and revising the auditing process for weatherization, would lower the audit unit cost. The program plans ranged from the offering of low-cost heating, water heating and infiltration measures, increased insulation levels, carpentry and plumbing services, to furnace or burner replacement. The program was configured to allow for very comprehensive weatherization and heating system servicing.

Automatic Measurement of Low Level Contamination on Concrete Surfaces

International Nuclear Information System (INIS)

Tachibana, M.; Itoh, H.; Shimada, T.; Yanagihara, S.

2002-01-01

Automatic measurement of radioactivity is necessary for considering cost effectiveness in final radiological survey of building structures in decommissioning nuclear facilities. The RAPID (radiation measuring pilot device for surface contamination) was developed to be applied to automatic measurement of low level contamination on concrete surfaces. The RAPID has a capability to measure contamination with detection limit of 0.14 Bq/cm2 for 60Co in 30 seconds of measurement time and its efficiency is evaluated to be 5 m2/h in a normal measurement option. It was confirmed that low level contamination on concrete surfaces could be surveyed by the RAPID efficiently compared with direct measurement by workers through its actual application

Researchers and Institutions in the Periphery: Challenges in Measuring Research Capacity for Geographically Specific Programs in the U.S

Energy Technology Data Exchange (ETDEWEB)

Melkers, J.

2016-07-01

The U.S. research funding system supports two geographically targeted government programs designed to enhance the research capacity of less competitive states in seeking federal research funds. Program eligibility is based on a relatively narrow measures of overall jurisdiction research funding track record. Yet, in order to adequately measure and address improved capacity development in these areas, a more nuanced understanding of the research capacity in these settings is needed. While the metric of prior research funding metric may be useful in assigning jurisdictions program eligibility, they do not account for variations within or across these areas, nor for factors that may function differently in lower capacity regions. This paper addresses the particular institutional and social/human capital aspects of measuring and identifying research capacity in these regions. Institutional data are used to categorize institutions within and across eligible jurisdictions. Survey data are used to address capacity issues and factors relevant to capacity development at the researcher level. (Author)

The influence of the program of Olympic education on the level of somatic health and physical training of secondary schools scholars.

Directory of Open Access Journals (Sweden)

Navtykov A.E.

2012-06-01

Full Text Available Influence of the program of Olympic education on the level of Olympic knowledge, somatic health and motive preparedness of schoolboys of middle ages was studied. In research 70 students took part 7 classes. The program of course of Olympic education was computer-integrated in extracurricular work of schoolboys. The program is counted on 26 hours. It contained the leadthrough of lectures (12 hours, seminar employments (4 hours, video of lessons (4 hours, спортивно-массовых measures on Olympic subject (3 hours, visit of sporting competitions and meeting with prominent sportsmen. It is set that introduction in the educational process of the program of Olympic education allows considerably to promote the level of knowledge, motivation and practical skills to operate in accordance with ideals and values of olympism. It results in the substantial improvement of physical health and motive preparedness of children.

Sustainable Materials Management: U.S. State Data Measurement Sharing Program

Science.gov (United States)

The State Data Measurement Sharing Program (SMP) is an online reporting, information sharing, and measurement tool that allows U.S. states to share a wide range of information about waste, recycling, and composting.

Investigation of Leveling Equipment for High Precision Measurements

International Nuclear Information System (INIS)

Gassner, G.

2007-01-01

At SLAC (Stanford Linear Accelerator Center) a fully automated vertical comparator for the calibration of digital levels and invar staffs was developed by the Metrology Department in cooperation with the Institute of Engineering Geodesy and Measurement Systems at the Graz University of Technology. This vertical comparator is the first in the US. With the vertical comparator it is possible to perform system calibration and CCD camera measurements of rods. System calibration uses the height readings of the digital level at different positions of the rod and compares them with the reference readings obtained by the interferometer. In the case of CCD camera measurements, the positions of the edges in the image is determined and again compared with the interferometer readings. This document gives an overview of the current set-up of the SLAC vertical comparator and experimental results of critical applications including measurements at the end sections of the rod, at critical sighting distances, with unfocused optics and under illumination with the digital levels in use at SLAC

National Low-Level Waste Management Program Radionuclide Report Series

International Nuclear Information System (INIS)

Rudin, M.J.; Garcia, R.S.

1992-02-01

This report, Volume 3 of the National Low-Level Radioactive Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of carbon-14. The report also discusses waste streams that contain carbon-14, waste forms that contain carbon-14, and carbon-14 behavior in the environment and in the human body

DepositScan, a Scanning Program to Measure Spray Deposition Distributions

Science.gov (United States)

DepositScan, a scanning program was developed to quickly measure spray deposit distributions on water sensitive papers or Kromekote cards which are widely used for determinations of pesticide spray deposition quality on target areas. The program is installed in a portable computer and works with a ...

Prevention validation and accounting platform: a framework for establishing accountability and performance measures of substance abuse prevention programs.

Science.gov (United States)

Kim, S; McLeod, J H; Williams, C; Hepler, N

2000-01-01

The field of substance abuse prevention has neither an overarching conceptual framework nor a set of shared terminologies for establishing the accountability and performance outcome measures of substance abuse prevention services rendered. Hence, there is a wide gap between what we currently have as data on one hand and information that are required to meet the performance goals and accountability measures set by the Government Performance and Results Act of 1993 on the other. The task before us is: How can we establish the accountability and performance measures of substance abuse prevention programs and transform the field of prevention into prevention science? The intent of this volume is to serve that purpose and accelerate the processes of this transformation by identifying the requisite components of the transformation (i.e., theory, methodology, convention on terms, and data) and by introducing an open forum called, Prevention Validation and Accounting (PREVA) Platform. The entire PREVA Platform (for short, the Platform) is designed as an analytic framework, which is formulated by a collectivity of common concepts, terminologies, accounting units, protocols for counting the units, data elements, and operationalizations of various constructs, and other summary measures intended to bring about an efficient and effective measurement of process input, program capacity, process output, performance outcome, and societal impact of substance abuse prevention programs. The measurement units and summary data elements are designed to be measured across time and across jurisdictions, i.e., from local to regional to state to national levels. In the Platform, the process input is captured by two dimensions of time and capital. Time is conceptualized in terms of service delivery time and time spent for research and development. Capital is measured by the monies expended for the delivery of program activities during a fiscal or reporting period. Program capacity is captured

Improving MC and A Oversight in Russia by Implementing Measurement and Training Programs

International Nuclear Information System (INIS)

Bokov, Dmitry; Byers, Kenneth R.

2004-01-01

As the Russian State regulatory agency responsible for oversight of nuclear material control and accounting (MC and A), Gosatomnadzor of Russia (GAN) determines the status of the MC and A programs at Russian facilities. Last year, GAN developed and implemented their Nuclear Material Measurement Program Plan which documents current non-destructive assay (NDA) measurement capability in all regions of GAN; provides justification for upgrades to equipment, procedures and training; and defines the inspector-facility operator interface as it relates to NDA measurement equipment use. This Program Plan has helped to give the GAN inspection measurements more legal and official status as an oversight tool, and has also helped to improve other GAN MC and A oversight activities. These improvements include developing a tamper-indicating device program, conducting NDA workshops at specific Russian nuclear facilities to better train MC and A inspectors, and developing training evaluation programs. The Program is an important tool to address the GAN role in oversight of the Russian Federal Information System nuclear material database. This paper describes the feedback received from the GAN regional offices on the implementation of the Program Plan during its first year in operation and how the Program Plan has affected other GAN inspection activities to improve MC and A oversight.

A Measurement Framework for Team Level Assessment of Innovation Capability in Early Requirements Engineering

Science.gov (United States)

Regnell, Björn; Höst, Martin; Nilsson, Fredrik; Bengtsson, Henrik

When developing software-intensive products for a market-place it is important for a development organisation to create innovative features for coming releases in order to achieve advantage over competitors. This paper focuses on assessment of innovation capability at team level in relation to the requirements engineering that is taking place before the actual product development projects are decided, when new business models, technology opportunities and intellectual property rights are created and investigated through e.g. prototyping and concept development. The result is a measurement framework focusing on four areas: innovation elicitation, selection, impact and ways-of-working. For each area, candidate measurements were derived from interviews to be used as inspiration in the development of a tailored measurement program. The framework is based on interviews with participants of a software team with specific innovation responsibilities and validated through cross-case analysis and feedback from practitioners.

Alpha radioactivity measurement technology with ionized air type measurement. Applicability evaluation to verification of the clearance level

International Nuclear Information System (INIS)

Mita, Yutaka; Matsumura, Toshihiro; Yokoyama, Kaoru; Sugitsue, Noritake

2008-10-01

The purpose of this test is to evaluate the applicability of the clearance level measuring system by Ionized Air Type Measurement after decontaminated by sulfuric acid sample. In Ningyo-toge Environmental Engineering Center. The equipment and radioactive waste which were contaminated with uranium are generated so much in future dismantling stage. In our plan, some of equipments and radioactive waste are contaminated to a clearance level, and cut down on decommission and disposal expense. This plan needs the alpha-rays measurement technology of the very low level. We think that ionized Air transfer measurement technology is promising as of clearance verification technology. The ionized Air transfer measurement technology applied to the Ionized Air Type Measurement can measure plan radioactivity of a very low level. Moreover, as compared with a direct survey, there is the merit which can be measured in a short time. However ionized Air transfer measurement technology is new technology. Therefore, there is almost no measurement track record. Furthermore, the date about the influence of a background, a detection limit, measurement performance, and reliability is insufficient. So, this measurement test estimated applicability as clearance level verification of an Ionized Air Type Measurement. (author)

User-Defined Data Distributions in High-Level Programming Languages

Science.gov (United States)

Diaconescu, Roxana E.; Zima, Hans P.

2006-01-01

One of the characteristic features of today s high performance computing systems is a physically distributed memory. Efficient management of locality is essential for meeting key performance requirements for these architectures. The standard technique for dealing with this issue has involved the extension of traditional sequential programming languages with explicit message passing, in the context of a processor-centric view of parallel computation. This has resulted in complex and error-prone assembly-style codes in which algorithms and communication are inextricably interwoven. This paper presents a high-level approach to the design and implementation of data distributions. Our work is motivated by the need to improve the current parallel programming methodology by introducing a paradigm supporting the development of efficient and reusable parallel code. This approach is currently being implemented in the context of a new programming language called Chapel, which is designed in the HPCS project Cascade.

NRC assessment of the high-level waste repository quality assurance program

International Nuclear Information System (INIS)

Kennedy, J.E.

1987-01-01

As part of its licensing responsibilities, the NRC is independently reviewing the DOE quality assurance program applied to the site characterization phase activities. Data collected and other information generated during this phase of the program will ultimately be used in a license application to demonstrate the suitability of one site for long-term isolation of waste. They must therefore fall under the quality assurance program to provide confidence in their adequacy. This NRC review consists of three main activities: development of staff guidance on quality assurance measures appropriate for site characterization activities; review of DOE QA plans and procedures; and audits and other reviews of the implementation of the program

Effects of aerobic and anaerobic training programs together with omega-3 supplement on interleukin-17 and CRP plasma levels in male mice.

Science.gov (United States)

Alizadeh, Hamid; Daryanoosh, Farhad; Moatari, Maryam; Hoseinzadeh, Khadijeh

2015-01-01

Herein, we studied the effects of two different exercise protocols on IL-17 and CRP plasma levels along with the anti-inflammatory effects of fish oil. The purpose of the present study was to investigate the effect of Eicosapentaenoic Acid (EPA) and Docosahexaenoic Acid (DHA) consumption along with two different types of physical activities on IL-17 and CRP plasma levels in trained male mice. A total of 130 adult male mice of Syrian race with the age of 2 months and the weight of 35±1 grams were selected. At the beginning, 10 mice were killed in order to determine the amounts of pre-test variables. The rest of the mice were randomly divided into 6 groups including control group (n=20), supplement (n=20), aerobic exercise (n=20), anaerobic exercise (n=20), supplementaerobic exercise (n=20), and supplement-anaerobic exercise (n=20). Blood samples were withdrawn from the tail under intraperitoneal ketamine and xylasine anaesthesia. The anaerobic training program included 8 weeks of running on treadmill, 3 sessions per week; the aerobic training program included 8 weeks of running on treadmill, 5 sessions per week. At the end of the training program, the blood sample from each group was taken in order to measure the CRP and IL-17 levels. The analysis of variance (ANOVA) was used to determine the differences among the groups. The results showed that there was a significant difference in IL-17 and CRP plasma levels between the groups after 8 weeks (Ptraining programs, both IL-17 and CRP plasma levels increased, although these observed increases were not same for two measured variables. The results might also show that the effect of the supplement depends on the type of training.

Interactive Approach for Multi-Level Multi-Objective Fractional Programming Problems with Fuzzy Parameters

Directory of Open Access Journals (Sweden)

M.S. Osman

2018-03-01

Full Text Available In this paper, an interactive approach for solving multi-level multi-objective fractional programming (ML-MOFP problems with fuzzy parameters is presented. The proposed interactive approach makes an extended work of Shi and Xia (1997. In the first phase, the numerical crisp model of the ML-MOFP problem has been developed at a confidence level without changing the fuzzy gist of the problem. Then, the linear model for the ML-MOFP problem is formulated. In the second phase, the interactive approach simplifies the linear multi-level multi-objective model by converting it into separate multi-objective programming problems. Also, each separate multi-objective programming problem of the linear model is solved by the ∊-constraint method and the concept of satisfactoriness. Finally, illustrative examples and comparisons with the previous approaches are utilized to evince the feasibility of the proposed approach.

Power Grid Construction Project Portfolio Optimization Based on Bi-level programming model

Science.gov (United States)

Zhao, Erdong; Li, Shangqi

2017-08-01

As the main body of power grid operation, county-level power supply enterprises undertake an important emission to guarantee the security of power grid operation and safeguard social power using order. The optimization of grid construction projects has been a key issue of power supply capacity and service level of grid enterprises. According to the actual situation of power grid construction project optimization of county-level power enterprises, on the basis of qualitative analysis of the projects, this paper builds a Bi-level programming model based on quantitative analysis. The upper layer of the model is the target restriction of the optimal portfolio; the lower layer of the model is enterprises’ financial restrictions on the size of the enterprise project portfolio. Finally, using a real example to illustrate operation proceeding and the optimization result of the model. Through qualitative analysis and quantitative analysis, the bi-level programming model improves the accuracy and normative standardization of power grid enterprises projects.

Liquid level measurement on coolant pipeline using Raman distributed temperature sensor

International Nuclear Information System (INIS)

Kasinathan, M.; Sosamma, S.; Babu Rao, C.; Murali, N.; Jayakumar, T.

2011-01-01

Optical fibre based Raman Distributed Temperature Sensor (RDTS) has been widely used for temperature monitoring in oil pipe line, power cable and environmental monitoring. Recently it has gained importance in nuclear reactor owing to its advantages like continuous, distributed temperature monitoring and immunity from electromagnetic interference. It is important to monitor temperature based level measurement in sodium capacities and in coolant pipelines for Fast Breeder Reactor (FBR). This particular application is used for filling and draining sodium in storage tank of sodium circuits of Fast breeder reactor. There are different conventional methods to find out the sodium level in the storage tank of sodium cooled reactors. They are continuous level measurement and discontinuous level measurement. For continuous level measurement, mutual inductance type level probes are used. The disadvantage of using this method is it needs a temperature compensation circuit. For discontinuous level measurement, resistance type discontinuous level probe and mutual inductance type discontinuous level probe are used. In resistance type discontinuous level probe, each level needs a separate probe. To overcome these disadvantages, RDTS is used for level measurement based distributed temperature from optical fibre as sensor. The feasibility of using RDTS for measurement of temperature based level measurement sensor is studied using a specially designed test set-up and using hot water, instead of sodium. The test set-up consist of vertically erected Stainless Steel (SS) pipe of length 2m and diameter 10cm, with provision for filling and draining out the liquid. Bare graded index multimode fibre is laid straight along the length of the of the SS pipe. The SS pipe is filled with hot water at various levels. The hot water in the SS pipe is maintained at constant temperature by insulating the SS pipe. The temperature profile of the hot water at various levels is measured using RDTS. The

TASKS OF INNOVATION PROCESSES PROGRAM-TARGET MANAGEMENT AT REGIONAL LEVEL

Directory of Open Access Journals (Sweden)

Mikhail Shchepakin

2015-09-01

Full Text Available The article analyzes the regional system of innovation management, discussed the existing problems of program-oriented management of innovative processes at the regional level, as well as possible solutions to improve the efficiency of the regional innovation system.

Solving the Fully Fuzzy Bilevel Linear Programming Problem through Deviation Degree Measures and a Ranking Function Method

Directory of Open Access Journals (Sweden)

Aihong Ren

2016-01-01

Full Text Available This paper is concerned with a class of fully fuzzy bilevel linear programming problems where all the coefficients and decision variables of both objective functions and the constraints are fuzzy numbers. A new approach based on deviation degree measures and a ranking function method is proposed to solve these problems. We first introduce concepts of the feasible region and the fuzzy optimal solution of a fully fuzzy bilevel linear programming problem. In order to obtain a fuzzy optimal solution of the problem, we apply deviation degree measures to deal with the fuzzy constraints and use a ranking function method of fuzzy numbers to rank the upper and lower level fuzzy objective functions. Then the fully fuzzy bilevel linear programming problem can be transformed into a deterministic bilevel programming problem. Considering the overall balance between improving objective function values and decreasing allowed deviation degrees, the computational procedure for finding a fuzzy optimal solution is proposed. Finally, a numerical example is provided to illustrate the proposed approach. The results indicate that the proposed approach gives a better optimal solution in comparison with the existing method.

National low-level waste management program radionuclide report series, Volume 15: Uranium-238

International Nuclear Information System (INIS)

Adams, J.P.

1995-09-01

This report, Volume 15 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of uranium-238 ( 238 U). The purpose of the National Low-Level Waste Management Program Radionuclide Report Series is to provide information to state representatives and developers of low-level radioactive waste disposal facilities about the radiological, chemical, and physical characteristics of selected radionuclides and their behavior in the waste disposal facility environment. This report also includes discussions about waste types and forms in which 238 U can be found, and 238 U behavior in the environment and in the human body

Measuring energy-saving retrofits: Experiences from the Texas LoanSTAR program

Energy Technology Data Exchange (ETDEWEB)

Haberl, J.S.; Reddy, T.A.; Claridge, D.E.; Turner, W.D.; O`Neal, D.L.; Heffington, W.M. [Texas A and M Univ., College Station, TX (United States). Energy Systems Lab.

1996-02-01

In 1988 the Governor`s Energy Management Center of Texas received approval from the US Department of Energy to establish a $98.6 million state-wide retrofit demonstration revolving loan program to fund energy-conserving retrofits in state, public school, and local government buildings. As part of this program, a first-of-its-kind, statewide Monitoring and Analysis Program (MAP) was established to verify energy and dollar savings of the retrofits, reduce energy costs by identifying operational and maintenance improvements, improve retrofit selection in future rounds of the LoanSTAR program, and initiate a data base of energy use in institutional and commercial buildings located in Texas. This report discusses the LoanSTAR MAP with an emphasis on the process of acquiring and analyzing data to measure savings from energy conservation retrofits when budgets are a constraint. This report includes a discussion of the program structure, basic measurement techniques, data archiving and handling, data reporting and analysis, and includes selected examples from LoanSTAR agencies. A summary of the program results for the first two years of monitoring is also included.

Measuring Service Quality in Recreational Programs with SERVQUAL.

Science.gov (United States)

Bauch, Joel R.

Many directors of college recreational programs are feeling pressure for increased accountability in the face of shrinking financial resources and increased demand for services. One method of providing that accountability and learning about the strengths and weaknesses of services offered is by assessing the level of client satisfaction. Developed…

National Low-Level Waste Management Program Radionuclide Report Series

International Nuclear Information System (INIS)

Rudin, M.J.; Stanton, C.; Patterson, R.G.; Garcia, R.S.

1992-02-01

This report, Volume 2 of the National Low-Level Radioactive Waste Management Program Radionuclide Report Series, discusses radiological and chemical characteristics of technetium-99. This report also includes discussions about waste streams in which technetium-99 can be found, waste forms that contain technetium-99, and technetium-99's behavior in the environment and in the human body

Impact of Support Services on Associate Level Nursing Programs

Science.gov (United States)

Busby-Parker, Michelle N.

2014-01-01

The goal of the research was to show the impact of the implementation of support services on admissions and graduation from nursing programs. The use of support services has been linked to higher levels of success in nursing students in the classroom and the work place. As nursing schools experience pressure to increase the student capacity to…

Estimation of the terrestrial gamma-ray levels from car-borne measurements

International Nuclear Information System (INIS)

Badran, H.M.

1998-01-01

A place to place variation of the gamma-radiation has been measured. The terrestrial gamma-ray levels were obtained with a portable Nal(Tl) detector. Gamma-ray levels were measured inside a car for a distance of about 220 km, from Norman up to Tulsa, Oklahoma, USA. Simultaneous measurements have also been carried out outside the vehicle and at distances 1 m and 5 m from the car. A series of data was collected every 1 mile (∼ 1.6 km). The measurements were also repeated different time under different conditions. The measured car-borne levels were correlated with the outdoor equivalent levels at 1 m above flat ground. The result permits a good estimation of the outdoor gamma-ray levels from the car measurements after the correction due to the vehicle shielding

Measurements of sea level off Tikkavanipalem - Coast India

Digital Repository Service at National Institute of Oceanography (India)

Joseph, A.; Desai, R.G.P.; Peshwe, V.B.; Desa, E.; VijayKumar, K.; Desa, E.S.; Mehra, P.; Nagvekar, S.

, and meteorological measurements were also made during this one-year period. These measurements have indicated that the sea level along this coast contains contributions from several classes of motions, principally tidal motions and set-up/set-down motions...

Effect of a Mindfulness Training Program on the Impulsivity and Aggression Levels of Adolescents with Behavioral Problems in the Classroom.

Science.gov (United States)

Franco, Clemente; Amutio, Alberto; López-González, Luís; Oriol, Xavier; Martínez-Taboada, Cristina

2016-01-01

Objective: The aim of the present study was to analyze the effects of a mindfulness training psycho-educative program on impulsivity and aggression levels in a sample of high school students. Methods: A randomized controlled trial with pre-test-post-test measurements was applied to an experimental group and a control group (waiting list). The Barratt Impulsivity Scale (BIS-11) Patton et al. (1995) and the Aggression Questionnaire (Buss and Perry, 1992) were used. Results: Statistical analyses showed a significant decrease in the levels of impulsivity and aggressiveness in the experimental group compared with the control group. These results have important implications for improving the level of academic engagement and self-efficacy of students and for reducing school failure. Conclusion: This is one of the first studies showing the effectiveness of mindfulness training at reducing impulsive and aggressive behaviors in the classroom. The efficacy of mindfulness-based programs is emphasized.

Nuclear Regulatory Commission low-level radioactive waste management program

International Nuclear Information System (INIS)

1977-09-01

It is believed that the priorities of NRC work in low-level waste management as described in this action plan are consistent with the needs of the overall national waste management program. Present licensing procedures and criteria are adequate for the short term, and priority attention is being given to the longer term, when the quantities of waste to be managed will be greater and licensing demand will increase. The plan makes use of expertise within NRC to achieve early results and is coordinated with other Federal agencies having related responsibilities. Since NRC decisions will affect industry, other governmental jurisdictions, private interest groups, and the public at large, procedures were developed to involve them in planning the program

Development of a technique for level measurement in pressure vessels using thermal probes and artificial neural networks

International Nuclear Information System (INIS)

Torres, Walmir Maximo

2008-01-01

A technique for level measurement in pressure vessels was developed using thermal probes with internal cooling and artificial neural networks (ANN's). This new concept of thermal probes was experimentally tested in an experimental facility (BETSNI) with two test sections, ST1 and ST2. Two different thermal probes were designed and constructed: concentric tubes probe and U tube probe. A data acquisition system (DAS) was assembled to record the experimental data during the tests. Steady state and transient level tests were carried out and the experimental data obtained were used as learning and recall data sets in the ANN's program RETRO-05 that simulate a multilayer perceptron with backpropagation. The results of the analysis show that the technique can be applied for level measurements in pressure vessel. The technique is applied for a less input temperature data than the initially designed to the probes. The technique is robust and can be used in case of lack of some temperature data. Experimental data available in literature from electrically heated thermal probe were also used in the ANN's analysis producing good results. The results of the ANN's analysis show that the technique can be improved and applied to level measurements in pressure vessels. (author)

Device to measure level in a steam drum of NPP

International Nuclear Information System (INIS)

Vinogradov, Yu.A.

1988-01-01

Gravitation-hydrostatic device for measuring coolant level in a steam drum of NPP is described. The device enables to improve the accuracy and sensitivity of measuring coolant level above and below the submerged perforated sheet of the steam drum and decrease the amount of levelling vessels in the unit by 50%. 1 fig

Foreign criteria and programs

International Nuclear Information System (INIS)

Swinth, K.L.; Thompson, I.M.G.

1993-03-01

The concept of measurement quality assurance (MQA) as embodied in National Institute of Standards and Technology (NIST) programs is not generally used within European programs for testing or accreditation. Although the essential elements of quality control and quality assurance are in the European programs, the concept of testing the capability of the laboratory itself, in terms of its performance for the designated measurements, may not be included. Rather, the European programs use the concept of periodic calibration of laboratory reference standards against the next highest level of standards. Thus, they embody the concept of measurement traceability to appropriate primary standards. Within Europe a series of calibration accreditation programs has been established in the various countries tied together through a multilateral agreement. The radiation measurement programs are based on the International Organization for Standardization (ISO) 9000 series of standards. The purpose of this paper is to outline the overall operation of European Accreditation Programs in the radiation calibration and measurement areas. The operation of the radiation measurement programs of the National Measurement Accreditation Service (NAMAS) in the United Kingdom is described in detail along with other European programs. The manner in which these programs relate to individual dosimetry service programs is also described

THE NUCLEAR MATERIAL MEASUREMENT PROGRAM PLAN FOR GOSATOMNADZOR OF RUSSIA

International Nuclear Information System (INIS)

Bokov, Dmitry; Byers, Kenneth R.

2003-01-01

As the Russian State regulatory agency responsible for oversight of nuclear material control and accounting (MC and A), Gosatomnadzor of Russia determines the status of the MC and A programs at Russian facilites by testing the nuclear material inventory for accounting record accuracy. Currently, Gosatomnadzor is developing and implementing an approach to planning and conducting MC and A inspections using non-destructive assay (NDA) instruments that will provide for consistent application of MC and A measurement inspection objectives throughtout Russia. This Gosatomnadzor NDA Program Plan documents current NDA measurement capability in all regions of Gosatomnadzor; provides justification for upgrades to equipment, procedures and training; and defines the inspector-facility operator interface as it relates to NDA measurement equipment use. This plan covers a three-year measurement program cycle, but will be reviewed and updated annually to ensure that adequate inspection resources are available to meet the demands of the inspection schedule. This paper presents the elements of this plan and describes the process by which Gosatomnadzor ensures that its NDA instruments are effectively utilized, procedures are developed and certified, and inspection personnel are properly trained to provide assurance that Russian nuclear facilities are in compliance with Russian MC and A regulations.

Measurement and monitoring technologies are important SITE program component

International Nuclear Information System (INIS)

Anon.

1988-01-01

An ongoing component of the Superfund Innovative Technologies Evaluation (SITE) Program, managed by the US EPA at its Hazardous Waste Engineering Research Laboratory in Cincinnati, is the development and demonstration of new and innovative measurement and monitoring technologies that will be applicable to Superfund site characterization. There are four important roles for monitoring and measurement technologies at Superfund sites: (1) to assess the extent of contamination at a site, (2) to supply data and information to determine impacts to human health and the environment, (3) to supply data to select the appropriate remedial action, and (4) to monitor the success or effectiveness of the selected remedy. The Environmental Monitoring Systems Laboratory in Las Vegas, Nevada (EMSL-LV) has been supporting the development of improved measurement and monitoring techniques in conjunction with the SITE Program with a focus on two areas: Immunoassay for toxic substances and fiber optic sensing for in-situ analysis at Superfund sites

Building a Unit-Level Mentored Program to Sustain a Culture of Inquiry for Evidence-Based Practice.

Science.gov (United States)

Breckenridge-Sproat, Sara T; Throop, Meryia D; Raju, Dheeraj; Murphy, Deborah A; Loan, Lori A; Patrician, Patricia A

2015-01-01

This study tested the effectiveness of a dynamic educational and mentoring program, facilitated by unit-level mentors, to introduce, promote, and sustain an evidence-based practice (EBP) culture among nurses in a military healthcare setting. The need to identify gaps in practice, apply principles of EBP, and advance scientific applications in the pursuit of quality nursing care is as important to military healthcare as it is in the civilian sector. The Advancing Research through Close Collaboration Model guided the intervention and study. Three instruments were used: the Organizational Readiness for System-wide Integration of Evidence-Based Practice, EBP Beliefs, and EBP Implementation scales. The study took place in 3 military hospitals simultaneously undergoing facility and staff integration. Data were collected from staff nurses in the inpatient nursing units before and after a facilitated education and mentoring intervention. Three hundred sixty nurses (38%) completed baseline, and 325 (31%) completed follow-up surveys. Scores improved on all 3 measures following implementation of the program; however, the differences were statistically significant only for the Organizational Readiness for System-wide Integration of Evidence-Based Practice scale (70.96 vs 77.63, t = -3.95, P culture may diffuse among individuals in an organization, even while experiencing significant change. It also demonstrates that a unit-level mentored EBP program is sustainable despite changes in organizational structure and workforce composition.

Measurement control workshop instructional materials

Energy Technology Data Exchange (ETDEWEB)

Gibbs, Philip [Brookhaven National Lab. (BNL), Upton, NY (United States); Harvel, Charles [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Clark, John [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gregg Protection Services, Lynchburg, VA (United States)

2012-09-01

An essential element in an effective nuclear materials control and accountability (MC&A) program is the measurement of the nuclear material as it is received, moved, processed and shipped. Quality measurement systems and methodologies determine the accuracy of the accountability values. Implementation of a measurement control program is essential to ensure that the measurement systems and methodologies perform as expected. A measurement control program also allows for a determination of the level of confidence in the accounting values.

Measurement control workshop instructional materials

Energy Technology Data Exchange (ETDEWEB)

Gibbs, Philip [Brookhaven National Lab. (BNL), Upton, NY (United States); Harvel, Charles [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Clark, John [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gregg Protection Services, Lynchburg, VA (United States)

2011-12-01

An essential element in an effective nuclear materials control and accountability (MC&A) program is the measurement of the nuclear material as it is received, moved, processed and shipped. Quality measurement systems and methodologies determine the accuracy of the accountability values. Implementation of a measurement control program is essential to ensure that the measurement systems and methodologies perform as expected. A measurement control program also allows for a determination of the level of confidence in the ac counting values.

Implementing and measuring the level of laboratory service integration in a program setting in Nigeria.

Science.gov (United States)

Mbah, Henry; Negedu-Momoh, Olubunmi Ruth; Adedokun, Oluwasanmi; Ikani, Patrick Anibbe; Balogun, Oluseyi; Sanwo, Olusola; Ochei, Kingsley; Ekanem, Maurice; Torpey, Kwasi

2014-01-01

The surge of donor funds to fight HIV&AIDS epidemic inadvertently resulted in the setup of laboratories as parallel structures to rapidly respond to the identified need. However these parallel structures are a threat to the existing fragile laboratory systems. Laboratory service integration is critical to remedy this situation. This paper describes an approach to quantitatively measure and track integration of HIV-related laboratory services into the mainstream laboratory services and highlight some key intervention steps taken, to enhance service integration. A quantitative before-and-after study conducted in 122 Family Health International (FHI360) supported health facilities across Nigeria. A minimum service package was identified including management structure; trainings; equipment utilization and maintenance; information, commodity and quality management for laboratory integration. A check list was used to assess facilities at baseline and 3 months follow-up. Level of integration was assessed on an ordinal scale (0 = no integration, 1 = partial integration, 2 = full integration) for each service package. A composite score grading expressed as a percentage of total obtainable score of 14 was defined and used to classify facilities (≤ 80% FULL, 25% to 79% PARTIAL and laboratory systems were 64 (52.5%) and 0 (0.0%) at baseline, compared to 100 (82.0%) and 3 (2.4%) respectively at 3 months follow-up (p = 0.000). This project showcases our novel approach to measure the status of each laboratory on the integration continuum.

Development of a low-level radioactive waste shipper model. National Low-Level Radioactive Waste Management Program

International Nuclear Information System (INIS)

1983-03-01

During 1982, Inter/Face Associates, Inc., conducted a low-level radioactive waste management survey of Nuclear Regulatory Commission (NRC) licensees in Massachusetts for the US Department of Energy's National Low-Level Waste Management Program. In the process of conducting the survey, a model was developed, based on existing NRC license classification systems, that would identify licensees who ship low-level waste for disposal. This report presents the model and documents the procedures used in developing and testing it. After the model was tested, several modifications were developed with the goal of determining the model's ability to identify waste shippers under different parameters. The report includes a discussion of the modifications

Development of a Computer Program for the Integrated Control of the Fuel Homogeneity Measurement System

International Nuclear Information System (INIS)

Shin, H. S.; Jang, J. W.; Lee, Y. H.; Oh, S. J.; Park, H. D.; Kim, C. K.

2005-11-01

The computer program is developed based on Visual C++, which is equipped with a user-friendly interface of the input/output(I/O) and a display function for the measuring conditions. This program consists of three parts which are the port communication, PLC(Programmable Logic Controller) and the MCA(Multi Channel Analyzer) control parts. The communication type between the CPU of the PLC module box and the computer is selected as be the Rs-232 asynchronous type and the thread method is adapted in the development of the first part of the program. The PLC-related program has been developed so that the data communication between the PLC CPU and the computer could be harmonized with the unique commands which have already been defined in the PLC. The measuring space and time intervals, the start and end ROI(region of interest) values, and the allowable error limitation are input at each measurement in this program. Finally the controlling MCA program has been developed by using Canberra's programming library which contains several files including the head files in which the variable and the function of C++ are declared according to the MCA function. The performance test has been carried out through an application of the developed computer program to the homogeneity measurement system. The gamma counts at 28 measuring points of a fuel rod of 700 mm in length are measured for 50 sec at each point. It was revealed that the measurement results are better than the previous ones in respects of the measurement accuracy and a measurement time saving could be achieved. It was concluded that the gamma measurement system can be improved through equipping it with the developed control program

Measurement of the area of venous ulcers using two software programs 1

Science.gov (United States)

Eberhardt, Thaís Dresch; de Lima, Suzinara Beatriz Soares; Lopes, Luis Felipe Dias; Borges, Eline de Lima; Weiller, Teresinha Heck; da Fonseca, Graziele Gorete Portella

2016-01-01

ABSTRACT Objective: to compare the measurement area of venous ulcers using AutoCAD(r) and Image Tool software. Method: this was an assessment of reproducibility tests conducted in a angiology clinic of a university hospital. Data were collected from 21 patients with venous ulcers, in the period from March to July of 2015, using a collection form and photograph of wounds. Five nurses (evaluators) of the hospital skin wound study group participated. The wounds were measured using both software programs. Data were analyzed using intraclass correlation coefficient, concordance correlation coefficient and Bland-Altman analysis. The study met the ethical aspects in accordance with current legislation. Results: the size of ulcers varied widely, however, without significant difference between the measurements; an excellent intraclass and concordance correlation was found between both software programs, which seem to be more accurate when measuring a wound area >10 cm². Conclusion: the use of both software programs is appropriate for measurement of venous ulcers, appearing to be more accurate when used to measure a wound area > 10 cm². PMID:27992028

Slow neutron mapping technique for level interface measurement

Science.gov (United States)

Zain, R. M.; Ithnin, H.; Razali, A. M.; Yusof, N. H. M.; Mustapha, I.; Yahya, R.; Othman, N.; Rahman, M. F. A.

2017-01-01

Modern industrial plant operations often require accurate level measurement of process liquids in production and storage vessels. A variety of advanced level indicators are commercially available to meet the demand, but these may not suit specific need of situations. The neutron backscatter technique is exceptionally useful for occasional and routine determination, particularly in situations such as pressure vessel with wall thickness up to 10 cm, toxic and corrosive chemical in sealed containers, liquid petroleum gas storage vessels. In level measurement, high energy neutrons from 241Am-Be radioactive source are beamed onto a vessel. Fast neutrons are slowed down mostly by collision with hydrogen atoms of material inside the vessel. Parts of thermal neutron are bounced back towards the source. By placing a thermal detector next to the source, these backscatter neutrons can be measured. The number of backscattered neutrons is directly proportional to the concentration of the hydrogen atoms in front of the neutron detector. As the source and detector moved by the matrix around the side of the vessel, interfaces can be determined as long as it involves a change in hydrogen atom concentration. This paper presents the slow neutron mapping technique to indicate level interface of a test vessel.

FJ-2207 measuring instrument detection pipe surface a level of pollution method

International Nuclear Information System (INIS)

Wang Jiangong

2010-01-01

On the pipe surface contamination were detected α level of pollution is a frequently encountered dose-detection work. Because the pipeline surface arc, while the measuring probe for the plane, which for accurate measurement difficult. In this paper, on the FJ-2207-type pipe surface contamination measuring instrument measuring pollution levels in the α method was studied. Introduced the FJ-2207 measuring instrument detection pipe surface α pollution levels. Studied this measuring instrument on the same sources of surface, plane α level of radioactivity measured differences in the results obtained control of the apparatus when the direct measurement of the surface correction factor, and gives 32-216 specifications commonly used pipe direct measurement of the amendment factor. Convenient method, test results are reliable for the accurate measurement of pipe pollution levels in the surface of α as a reference and learning. (authors)

Recruitment into diabetes prevention programs: what is the impact of errors in self-reported measures of obesity?

Science.gov (United States)

Hernan, Andrea; Philpot, Benjamin; Janus, Edward D; Dunbar, James A

2012-07-08

Error in self-reported measures of obesity has been frequently described, but the effect of self-reported error on recruitment into diabetes prevention programs is not well established. The aim of this study was to examine the effect of using self-reported obesity data from the Finnish diabetes risk score (FINDRISC) on recruitment into the Greater Green Triangle Diabetes Prevention Project (GGT DPP). The GGT DPP was a structured group-based lifestyle modification program delivered in primary health care settings in South-Eastern Australia. Between 2004-05, 850 FINDRISC forms were collected during recruitment for the GGT DPP. Eligible individuals, at moderate to high risk of developing diabetes, were invited to undertake baseline tests, including anthropometric measurements performed by specially trained nurses. In addition to errors in calculating total risk scores, accuracy of self-reported data (height, weight, waist circumference (WC) and Body Mass Index (BMI)) from FINDRISCs was compared with baseline data, with impact on participation eligibility presented. Overall, calculation errors impacted on eligibility in 18 cases (2.1%). Of n = 279 GGT DPP participants with measured data, errors (total score calculation, BMI or WC) in self-report were found in n = 90 (32.3%). These errors were equally likely to result in under- or over-reported risk. Under-reporting was more common in those reporting lower risk scores (Spearman-rho = -0.226, p-value recruit participants at moderate to high risk of diabetes, accurately categorising levels of overweight and obesity using self-report data. The results could be generalisable to other diabetes prevention programs using screening tools which include self-reported levels of obesity.

Perceived Effectiveness of Professional Development Programs of Teachers at Higher Education Level

Science.gov (United States)

Malik, Sufiana Khatoon; Nasim, Uzma; Tabassum, Farkhanda

2015-01-01

The major purpose of the study was to assess the perceived effectiveness of professional development programs of teachers at higher educational level. The objectives of the study were: "to assess university level teachers'" opinion about effectiveness of professional development training with reference to quality teaching, to measure…

Low-level waste management program and interim waste operations technologies

International Nuclear Information System (INIS)

Mezga, L.J.

1983-01-01

The Department of Energy currently supports an integrated technology development and transfer program aimed at ensuring that the technology necessary for the safe management and disposal of LLW by the commercial and defense sectors is available. The program focuses on five technical areas: (1) corrective measures technology, (2) improved shallow land burial technology, (3) greater confinement disposal technology, (4) model development and validation, and (5) treatment methods for problem wastes. The results of activities in these areas are reported in the open literature and the Proceedings of the LLWMP Annual Participants Information Meeting

DOE Low-Level Waste Management Program

International Nuclear Information System (INIS)

Mezga, L.J.

1983-01-01

The Oak Ridge National Laboratory (ORNL) in its role as associate lead contractor of the DOE LLWMP has responsibility for the management of program-funded technology development activities. In this role with general guidance provided by DOE and the lead contractor (EG and G Idaho), the ORNL program office is charged with the responsibility to (1) develop program plans for the major technology areas, (2) recommend allocations for the program resources, (3) review the technology development tasks to ensure that program objectives are being met, and (4) to assist the lead contractor in coordinating the DOE LLWMP with other on-going US and foreign waste technology programs. Although the ORNL office generally assists the lead laboratory in management of the total program, our emphasis is on management of R and D for development of basic technology and to assess concepts for alternative systems of processing and disposal of LLW. Technical progress for each of the tasks of this program for FY 1982 is summarized

Video training and certification program improves reliability of postischemic neurologic deficit measurement in the rat.

Science.gov (United States)

Taninishi, Hideki; Pearlstein, Molly; Sheng, Huaxin; Izutsu, Miwa; Chaparro, Rafael E; Goldstein, Larry B; Warner, David S

2016-12-01

Scoring systems are used to measure behavioral deficits in stroke research. Video-assisted training is used to standardize stroke-related neurologic deficit scoring in humans. We hypothesized that a video-assisted training and certification program can improve inter-rater reliability in assessing neurologic function after middle cerebral artery occlusion in rats. Three expert raters scored neurologic deficits in post-middle cerebral artery occlusion rats using three published systems having different complexity levels (3, 18, or 48 points). The system having the highest point estimate for the correlation between neurologic score and infarct size was selected to create a video-assisted training and certification program. Eight trainee raters completed the video-assisted training and certification program. Inter-rater agreement ( Κ: score) and agreement with expert consensus scores were measured before and after video-assisted training and certification program completion. The 48-point system correlated best with infarct size. Video-assisted training and certification improved agreement with expert consensus scores (pretraining = 65 ± 10, posttraining = 87 ± 14, 112 possible scores, P  0.4 (pretraining = 4, posttraining = 9), and number of categories with an improvement in the Κ: score from pretraining to posttraining (n = 6). Video-assisted training and certification improved trainee inter-rater reliability and agreement with expert consensus behavioral scores in rats after middle cerebral artery occlusion. Video-assisted training and certification may be useful in multilaboratory preclinical studies. © The Author(s) 2015.

High performance gamma measurements of equipment retrieved from Hanford high-level nuclear waste tanks

International Nuclear Information System (INIS)

Troyer, G.L.

1997-01-01

The cleanup of high level defense nuclear waste at the Hanford site presents several progressive challenges. Among these is the removal and disposal of various components from buried active waste tanks to allow new equipment insertion or hazards mitigation. A unique automated retrieval system at the tank provides for retrieval, high pressure washing, inventory measurement, and containment for disposal. Key to the inventory measurement is a three detector HPGe high performance gamma spectroscopy system capable of recovering data at up to 90% saturation (200,000 counts per second). Data recovery is based on a unique embedded electronic pulser and specialized software to report the inventory. Each of the detectors have different shielding specified through Monte Carlo simulation with the MCNP program. This shielding provides performance over a dynamic range of eight orders of magnitude. System description, calibration issues and operational experiences are discussed

High performance gamma measurements of equipment retrieved from Hanford high-level nuclear waste tanks

Energy Technology Data Exchange (ETDEWEB)

Troyer, G.L.

1997-03-17

The cleanup of high level defense nuclear waste at the Hanford site presents several progressive challenges. Among these is the removal and disposal of various components from buried active waste tanks to allow new equipment insertion or hazards mitigation. A unique automated retrieval system at the tank provides for retrieval, high pressure washing, inventory measurement, and containment for disposal. Key to the inventory measurement is a three detector HPGe high performance gamma spectroscopy system capable of recovering data at up to 90% saturation (200,000 counts per second). Data recovery is based on a unique embedded electronic pulser and specialized software to report the inventory. Each of the detectors have different shielding specified through Monte Carlo simulation with the MCNP program. This shielding provides performance over a dynamic range of eight orders of magnitude. System description, calibration issues and operational experiences are discussed.

Identifying Assets Associated with Quality Extension Programming at the Local Level

Directory of Open Access Journals (Sweden)

Amy Harder

2017-10-01

Full Text Available County Extension offices are responsible for the majority of programming delivered in the United States. The purpose of this study was to identify and explore assets influencing the quality of county Extension programs. A basic qualitative research design was followed to conduct constant comparative analysis of five Extension county program review reports. Using the appreciative inquiry process as the lens through which to view the county program review reports revealed multiple assets leading to quality programming. Assets of the reviewed county Extension programs were found to cluster within the following themes: competent and enthusiastic Extension faculty, community partnerships, engaged and supportive stakeholders, effective resource management, sufficient and stable workforce, meeting stakeholder needs, positive reputation, access to facilities, positive relationships between county and state faculty, and innovative practices. The use of both needs-based and assets-based paradigms will provide Extension organizations with a more holistic understanding of its assets and a research-based foundation from which to make decisions about strengthening the organization at all levels.

Microcontroller based multi-channel ultrasonic level monitoring system

International Nuclear Information System (INIS)

Ambastha, K.P.; Chaudhari, Y.V.; Singh, Inder Jeet; Chadda, V.K.

2004-01-01

Microcontroller based Multi-channel Ultrasonic Level Monitoring System developed by Computer Division is based on echo ranging techniques to monitor level. The transmitter directs an ultrasonic burst towards the liquid, which gets reflected from the top of the liquid surface. The time taken for ultrasound to travel from the transmitter to the top of liquid surface is measured and used to calculate the liquid level. The system provides for temperature compensation for accurate measurement as the ultrasound velocity depends on the ambient temperature. It can measure liquid level up to 5 meters. A single monitor can be used to measure level in 6 tanks. PC connectivity has been provided via RS 232 and RS 485 for remote operation and data logging of level. A GUI program developed using LABVIEW package displays level on PC monitor. The program provides for pictorial as well as numerical display for level and temperature in the front panel on the PC monitor. A user can monitor level for any or all tanks from the PC. One unit is installed at CIRUS for measuring level in Acid/ Alkali tanks and one is installed at APSARA for measuring water level in the reactor pool. (author)

Six Sigma Evaluation of the High Level Waste Tank Farm Corrosion Control Program at the Savannah River Site

International Nuclear Information System (INIS)

Hill, P. J.

2003-01-01

Six Sigma is a disciplined approach to process improvement based on customer requirements and data. The goal is to develop or improve processes with defects that are measured at only a few parts per million. The process includes five phases: Identify, Measure, Analyze, Improve, and Control. This report describes the application of the Six Sigma process to improving the High Level Waste (HLW) Tank Farm Corrosion Control Program. The report documents the work performed and the tools utilized while applying the Six Sigma process from September 28, 2001 to April 1, 2002. During Fiscal Year 2001, the High Level Waste Division spent $5.9 million to analyze samples from the F and H Tank Farms. The largest portion of these analytical costs was $2.45 million that was spent to analyze samples taken to support the Corrosion Control Program. The objective of the Process Improvement Project (PIP) team was to reduce the number of analytical tasks required to support the Corrosion Control Program by 50 percent. Based on the data collected, the corrosion control decision process flowchart, and the use of the X-Y Matrix tool, the team determined that analyses in excess of the requirements of the corrosion control program were being performed. Only two of the seven analytical tasks currently performed are required for the 40 waste tanks governed by the Corrosion Control Program. Two additional analytical tasks are required for a small subset of the waste tanks resulting in an average of 2.7 tasks per sample compared to the current 7 tasks per sample. Forty HLW tanks are sampled periodically as part of the Corrosion Control Program. For each of these tanks, an analysis was performed to evaluate the stability of the chemistry in the tank and then to determine the statistical capability of the tank to meet minimum corrosion inhibitor limits. The analyses proved that most of the tanks were being sampled too frequently. Based on the results of these analyses and th e use of additional

45 CFR 305.2 - Performance measures.

Science.gov (United States)

2010-10-01

... PROGRAM PERFORMANCE MEASURES, STANDARDS, FINANCIAL INCENTIVES, AND PENALTIES § 305.2 Performance measures. (a) The child support incentive system measures State performance levels in five program areas... 45 Public Welfare 2 2010-10-01 2010-10-01 false Performance measures. 305.2 Section 305.2 Public...

Quality assurance program plan for low-level waste at the WSCF Laboratory

International Nuclear Information System (INIS)

Morrison, J.A.

1994-01-01

The purpose of this document is to provide guidance for the implementation of the Quality Assurance Program Plan (QAPP) for the management of low-level waste at the Waste Sampling and Characterization Facility (WSCF) Laboratory Complex as required by WHC-CM-4-2, Quality Assurance Manual, which is based on Quality Assurance Program Requirements for Nuclear Facilities, NQA-1 (ASME)

A measurement control program for plutonium isotopic gamma-ray systems at the Rocky Flats Plant

International Nuclear Information System (INIS)

Fleissner, J.G.

1986-01-01

A sound measurement control (MC) program should be an integral part of every nondestructive assay measurement system used for the assay of special nuclear materials. This paper describes a measurement control program for plutonium isotopic composition measurements, using high-resolution gamma-ray spectroscopy, that has been implemented in the Analytical Laboratories and the Chemistry Standards Laboratory at the Rocky Flats Plant. This MC program emphasizes the standardization of data collection procedures along with the implementation of internal and external measurement control checks to provide the requisite measurement quality assurance

Relating measurement invariance, cross-level invariance, and multilevel reliability

OpenAIRE

Jak, S.; Jorgensen, T.D.

2017-01-01

Data often have a nested, multilevel structure, for example when data are collected from children in classrooms. This kind of data complicate the evaluation of reliability and measurement invariance, because several properties can be evaluated at both the individual level and the cluster level, as well as across levels. For example, cross-level invariance implies equal factor loadings across levels, which is needed to give latent variables at the two levels a similar interpretation. Reliabili...

Implementation Measurement for Evidence-Based Violence Prevention Programs in Communities.

Science.gov (United States)

Massetti, Greta M; Holland, Kristin M; Gorman-Smith, Deborah

2016-08-01

Increasing attention to the evaluation, dissemination, and implementation of evidence-based programs (EBPs) has led to significant advancements in the science of community-based violence prevention. One of the prevailing challenges in moving from science to community involves implementing EBPs and strategies with quality. The CDC-funded National Centers of Excellence in Youth Violence Prevention (YVPCs) partner with communities to implement a comprehensive community-based strategy to prevent violence and to evaluate that strategy for impact on community-wide rates of violence. As part of their implementation approach, YVPCs document implementation of and fidelity to the components of the comprehensive youth violence prevention strategy. We describe the strategies and methods used by the six YVPCs to assess implementation and to use implementation data to inform program improvement efforts. The information presented describes the approach and measurement strategies employed by each center and for each program implemented in the partner communities. YVPCs employ both established and innovative strategies for measurement and tracking of implementation across a broad range of programs, practices, and strategies. The work of the YVPCs highlights the need to use data to understand the relationship between implementation of EBPs and youth violence outcomes.

Evaluation of bubbler/diaphragm techniques to measure surface level in the waste storage tanks

International Nuclear Information System (INIS)

Peters, T.J.; Hickman, B.J.; Colson, J.B.

1993-10-01

This report describes the results of tests conducted at the Pacific Northwest Laboratory (PNL) to determine if a bubbler technique can be used to determine the surface level in the waste tanks. Two techniques were evaluated. The first technique is a standard bubbler system in which a tube is placed below the surface of the liquid to be measured and air pressure inside a tube is increased until bubbles begin to become emitted from the tube. The air pressure then is a function of the pressure at the bottom of the tube. The second technique involves a system similar to the standard bubbler technique, but instead of bubbles being released into the material to be gauged, air pressure is increased against a diaphragm until enough pressure is applied to overcome the pressure of the liquid at the given depth, at which time the air then flows in a return loop back to a vent. The advantage of the diaphragm system is that it is a sealed system; thus no air is released into the waste tank materials, and it is not possible for the waste tank materials to get into the air flow. Based on the results of the tests conducted in this program, it appears that the bubbler and diaphragm systems that were tested could not be used for accurate measurements of the level in the waste tanks. Both exhibited deposits of simulated waste tank material at the end of the devices which affected the ability of the gauge to accurately determine changes in the surface level even though the measured value of the level was inaccurate. Further investigations into the cause of this inaccuracy may be warranted. Alternate diaphragm materials may improve the performance of this gauge

Optimal Design of Measurement Programs for the Parameter Identification of Dynamic Systems

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Sørensen, John Dalsgaard; Brincker, Rune

1993-01-01

The design of a measurement program devoted to parameter identification of structural dynamic systems is considered. The design problem is formulated as an optimization problem to minimize the total expected cost that is the cost of failure and the cost of the measurement program. All...... the calculations are based on a priori knowledge and engineering judgement. One of the contribution of the approach is that the optimal number of sensory can be estimated. This is shown in an numerical example where the proposed approach is demonstrated. The example is concerned with design of a measurement...

Optimal Design of Measurement Programs for the Parameter Identification of Dynamic Systems

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Sørensen, John Dalsgaard; Brincker, Rune

1991-01-01

The design of a measurement program devoted to parameter identification of structural dynamic systems is considered. The design problem is formulated as an optimization problem to minimize the total expected cost, i.e. the cost of failure and the cost of the measurement program. All...... the calculations are based on a priori knowledge and engineering judgement. One of the contributions of the approach is that the optimal number of sensors can be estimated. This is shown in a numerical example where the proposed approach is demonstrated. The example is concerned with design of a measurement...

Overview of the Nuclear Regulatory Commission Low-Level Waste Management Program

International Nuclear Information System (INIS)

Bishop, W.P.; Bell, M.J.; Dragonette, K.S.; Adam, J.

1979-01-01

Environmental impacts from Table S-3 of 10 CFR Part 51 are included in individual environmental impact statements for LWR's. In response to a U.S. Court of Appeals finding of inadequate documentation to support Table S-3, ''Environmental Survey of Reprocessing and Waste Management Portions of the LWR Fuel Cycle'' (NUREG-0116) and ''Public Comments and Task Force Responses Regarding Environmental Survey of the Reprocessing and Waste Portions of the LWR Fuel Cycle'' (NUREG-0216) were published. As a result of these in-house studies, an interim rule revising Table S-3 has been published. These documents include discussions of shallow land burial of low-level waste, past experiences and sensitivity calculations estimating potential dose commitments from the groundwater migration of the wastes. An NRC task force report (NUREG-0217) examining the Federal and Agreement State programs for regulating commercial low-level waste disposal recommends increasing the federal role in low-level waste disposal. The need to investigate alternatives to shallow land burial is identified. The NRC is developing a radioactive waste management program which includes a plan for the implementation of the task force recommendations, the development of environmental impacts for low-level waste disposal, development of standards and criteria, and the establishment of a regulatory framework and licensing procedures for the disposal of low-level radioactive waste

LOWRAD 96. Methods and applications of low-level radioactivity measurements. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Fietz, J [ed.; Forschungszentrum Rossendorf e.V. (FZR), Dresden (Germany)

1997-03-01

The newest developments in the field of low-level radioactivity measurements and new applications for existing and low-level measuring facilities are presented. The contributions mostly were devoted to basic physical aspects and applications of low-level counting. Papers on chemical separation and preparation techniques and on low-level radiation dose determinations were also presented. (DG)

Quantum Biology at the Cellular Level - elements of the research program

OpenAIRE

Bordonaro, Michael; Ogryzko, Vasily

2013-01-01

Quantum Biology is emerging as a new field at the intersection between fundamental physics and biology, promising novel insights into the nature and origin of biological order. We discuss several elements of QBCL (Quantum Biology at Cellular Level), a research program designed to extend the reach of quantum concepts to higher than molecular levels of biological organization. Key words. decoherence, macroscopic superpositions, basis-dependence, formal superposition, non-classical correlations,...

Environmental Measurements Laboratory program review, December 1983

International Nuclear Information System (INIS)

Volchok, H.L.; de Planque, G.

1984-03-01

This volume contains all of the written material that was submitted to the panel of Reviewers in advance of a Program Review conducted by the US Department of Energy, Office of Health and Environmental Research at the Environmental Measurements Laboratory (EML) December 7-9, 1983. In addition to a general introduction there are nineteen papers grouped into the five broad program categories covering all of the scientific and engineering projects of the Laboratory: Natural Radioactivity and Radiation, Anthropogenic Radioactivity and Radiation, Non-nuclear, Quality Assurance, and Development and Support. These short articles, for the most part, focus on the rationale for EML's involvement in each project, emphasizing their relevance to the EML and Department of Energy missions. Project results and their interpretation were presented at the Review and can be found in the material referenced in this volume

IRIB’s Religious and Non-religious Programs and their Impacts on Religiosity Levels

Directory of Open Access Journals (Sweden)

Azam Ravadrad

2009-08-01

Full Text Available This paper attempts to study the correlation between IRIB’s Religious and Non-religious programs, and the levels of religiosity in Iran. Accordingly, I would firstly explain the key concepts as religious program, non-religious program, religious broadcasting, and Ideological broadcasting; then, analyzing some instant programs, from non-religious to religious, I would attempt to formulize their impacts on one’s definition of religion –either as a private or simultaneously private and public matter. It is shown that in the trilogy of purely religious, purely entertaining, and mediated religious programs, it is the third which satisfy a religious television’s ideal.

National energy peak leveling program (NEPLP). Final report

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

This multisectioned three-Volume report is responsive to the requirements of Contract E (04-3)-1152 to provide a detailed methodology, to include management, technology, and socio-economic aspects, of a voluntary community program of computer-assisted peak load leveling and energy conservation in commercial community facilities. The demonstration project established proof-of-concept in reducing the kW-demand peak by the unofficial goal of 10%, with concurrent kWh savings. This section of volume III contains appendixes of information on load shedding determination, analysis, socio-economic study, contractual cross references, and definitions.

National energy peak leveling program (NEPLP). Final report

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

This three-volume report is responsive to the requirements of contract E (04-3)-1152 to provide a detailed methodology, to include management, technology, and socio-economic aspects, of a voluntary community program for computer-assisted peak load leveling and energy conservation in commercial community facilities. The demonstration project established proof-of-concept in reducing the kW-demand peak by the unofficial goal of 10%, with concurrent kWh savings. The report consists of the following three volumes: Volume I: management overview; Volume II: methodology and technology; and Volume III; appendices.

Evaluation of the Automatic Density Compensation for Pressurizer Level Measurement

International Nuclear Information System (INIS)

Jeong, Insoo; Min, Seohong; Ahn, Myunghoon

2014-01-01

When using two transmitters, it is difficult for the operators to identify the correct level of the pressurizer (PZR) upon failure of one of the two transmitters. For this reason, Korean Utility Requirements Document (KURD) requires that the operators to use three independent level indicators. Two hot calibrated transmitters and one cold calibrated transmitter compose PZR level transmitters in APR1400. In this paper, the deviation between cold calibration and hot calibration is evaluated, and the application of compensated PZR level measurement and uncompen-sated PZR level measurement during the normal operation of APR1400 are introduced. The PZR level signals for APR1400 come in three channels. To satisfy the KURD requirements for PZR level measurement, and at the same time to accomplish correction design and implementation, applicability and differences between hot calibration and cold calibration, compensated level and uncompensated level were evaluated as follows: For proper indication of PZR levels under normal operating condition, two of the three transmitters went through hot calibration and the remaining one transmitter went through cold calibration. This was to allow indicating entire regions of PZR regardless of the plant operation modes. For automatic density compensation per KURD requirements, the algorithm of the density compensated PZR level implemented in the DCS controller and PRV logic is adopted as a signal validation method

Evaluation of a multiple ecological level child obesity prevention program: Switch® what you Do, View, and Chew

Directory of Open Access Journals (Sweden)

Callahan Randi

2009-09-01

Full Text Available Abstract Background Schools are the most frequent target for intervention programs aimed at preventing child obesity; however, the overall effectiveness of these programs has been limited. It has therefore been recommended that interventions target multiple ecological levels (community, family, school and individual to have greater success in changing risk behaviors for obesity. This study examined the immediate and short-term, sustained effects of the Switch program, which targeted three behaviors (decreasing children's screen time, increasing fruit and vegetable consumption, and increasing physical activity at three ecological levels (the family, school, and community. Methods Participants were 1,323 children and their parents from 10 schools in two states. Schools were matched and randomly assigned to treatment and control. Measures of the key behaviors and body mass index were collected at baseline, immediately post-intervention, and 6 months post-intervention. Results The effect sizes of the differences between treatment and control groups ranged between small (Cohen's d = 0.15 for body mass index at 6 months post-intervention to large (1.38; parent report of screen time at 6 months post-intervention, controlling for baseline levels. There was a significant difference in parent-reported screen time at post-intervention in the experimental group, and this effect was maintained at 6 months post-intervention (a difference of about 2 hours/week. The experimental group also showed a significant increase in parent-reported fruit and vegetable consumption while child-reported fruit and vegetable consumption was marginally significant. At the 6-month follow-up, parent-reported screen time was significantly lower, and parent and child-reported fruit and vegetable consumption was significantly increased. There were no significant effects on pedometer measures of physical activity or body mass index in the experimental group. The intervention effects

Community-Level Measures of Stroke Knowledge among Children: Findings from Hip Hop Stroke.

Science.gov (United States)

Simmons, Cailey; Noble, James M; Leighton-Herrmann, Ellyn; Hecht, Mindy F; Williams, Olajide

2017-01-01

Community-level determinants of stroke knowledge among children are unknown but could meaningfully impact public stroke education campaigns. We explored for associations between community- and school-level quality measures relative to baseline stroke knowledge among children participating in the Hip Hop Stroke program. Baseline stroke knowledge assessments were performed in 2839 fourth-, fifth-, and sixth-grade students (ages 9-11 years) from November 2005 to April 2014. Knowledge was assessed relative to school performance grade (SPG, graded A-F; a school-level measure determined by the New York City [NYC] Department of Education) and economic need index (ENI, range: 0-2; a community-level, within-school measure of subsidized housing and meals with higher scores indicating more socioeconomic distress). Schools studied included those with SPG = B (n = 196), SPG = C (n = 1590), and SPG = D (n = 1053) and mean ENI = .85 (standard deviation: .23). A composite assessment of knowledge, including 4 stroke symptoms (blurred vision, facial droop, sudden headache, and slurred speech), was conducted consistently since 2006. Overall, students correctly identified a mean of 1.74 stroke symptoms (95% confidence interval: 1.70-1.79; possible range: 0-4, expected value of chance response alone or no knowledge = 2). For quartiles of ENI, mean knowledge scores are as follows: ENI Q1  = 2.00, ENI Q2  = 2.09, ENI Q3  = 1.46, and ENI Q4  = 1.56 (ENI Q3 and ENI Q4 versus ENI Q1 , P < .001). For SPG, SPG = B schools: 2.09, SPG = C: 1.83, and SPG = D: 1.56 (SPG = C and SPG = D versus SPG = B schools, P ≤ .05). Children's stroke knowledge was lowest in NYC communities with greater economic need and lower school performance. These findings could guide stroke education campaign implementation strategies. Copyright © 2017 National Stroke Association. Published by Elsevier Inc. All rights reserved.

41 CFR 102-192.145 - Which program levels should have a mail manager?

Science.gov (United States)

2010-07-01

... should have a mail manager? 102-192.145 Section 102-192.145 Public Contracts and Property Management... have a mail manager? Every program level within a Federal agency that generates a significant quantity of outgoing mail should have its own mail manager. Each agency must decide which programs will have a...

Paddy farmer households’ participation and food security level in special effort program in Seputih Raman sub-district of Central Lampung Regency

Science.gov (United States)

Rangga, K. K.; Syarief, Y. A.

2018-03-01

The objectives of this study are to study the participation of paddy farmers in the Special Effort program to increase paddy production, to study the level of household food security of paddy farmers, and to analyze the correlation between farmer participation and food security level of paddy farmers. The location was chosen purposively in Seputih Raman sub-district. The data were collected from December 2016 to February 2017. The population of this study was paddy farmers who participating in Special Effort program. The hypothesis was tested by using Spearman’s Rank correlation test. Farmer household’s food security was measured objectively based on the share of household’s food expenditure and subjectively based on the opinion, views, and attitudes or farmers’ opinions on food availability, food distribution, and household food consumption. This research showed that farmers’ participation in Special Effort program in Seputih Raman Sub Ditrict, Central Lampung Regency belonged to medium classification, household food security either objectively or subjectively was in food resistant condition of medium classification, and there was significant correlation between farmers’ participation and food security level of paddy farmer household.

A personalized, intense physical rehabilitation program improves walking in people with multiple sclerosis presenting with different levels of disability: a retrospective cohort.

Science.gov (United States)

Kalron, Alon; Nitzani, Dalia; Magalashvili, David; Dolev, Mark; Menascu, Shay; Stern, Yael; Rosenblum, Uri; Pasitselsky, Diana; Frid, Lior; Zeilig, Gabi; Barmatz, Caroline; Givon, Uri; Achiron, Anat

2015-03-04

People with multiple sclerosis (PwMS) endure walking limitations. To address this restriction, various physical rehabilitation programs have been implemented with no consensus regarding their efficacy. Our objective was to report on the efficacy of an integrated tailored physical rehabilitation program on walking in people with multiple sclerosis categorized according to their level of neurological disability. Retrospective data were examined and analyzed. Specifically, data obtained from all patients who participated in the Multiple Sclerosis Center's 3 week rehabilitation program were extracted for in depth exploration. The personalized rehabilitation program included three major components modified according to the patient's specific impairments and functional needs: (a) goal directed physical therapy (b) moderately intense aerobic exercise training on a bicycle ergometer and (c) aquatic therapy chiefly oriented to body structures appropriate to movement. Gait outcome measurements included the 10 meter, 20 meter, Timed up and go and 2 minute walking tests measured pre and post the rehabilitation program. Three hundred and twelve people with relapsing-remitting multiple sclerosis were included in the final analysis. Patients were categorized into mild (n = 87), moderate (n = 104) and severely (n = 121) disabled groups. All clinical walking outcome measurements demonstrated statistically significant improvements, however, only an increase in the 2 minute walking test was above the minimal clinical difference value. The moderate and severe groups considerably improved compared to the mild gait disability group. Mean change scores (%) of the pre-post intervention period of the 2 minute walking test were 19.0 (S.E. = 3.4) in the moderate group, 16.2 (S.E. = 5.4) in the severe group and 10.9 (S.E. = 2.3) in the mild gait disability group. We presented comprehensive evidence verifying the effects of an intense goal-directed physical

Our Continuing Program of Optical Color Measurements of Centaurs and KBOs

Science.gov (United States)

Romanishin, W.; Tegler, S. C.; Consolmagno, G. J.

2012-05-01

We report on our continuing program of BVR color measurement of Centaurs and KBOs. Most of our measurements have been made with the Vatican Advanced Technology Telescope (VATT). We report of new colors obtained through October 2011.

Low-level radioactive waste program of the US Geological Survey - in transition

International Nuclear Information System (INIS)

Fischer, J.N.

1983-01-01

In 1983, the US Geological Survey will publish final reports of geohydrologic investigations at five commercial low-level, radioactive-waste burial sites in the United States. These reports mark the end of the first phase of the US Geological Survey program to improve the understanding of earth-science principles related to the effective disposal of low-level wastes. The second phase, which was initiated in 1981, is being developed to address geohydrologic issues identified as needing greater attention based upon results of the first-phase site studies. Specific program elements include unsaturated-zone hydrology, geochemistry, clay mineralogy, surface geophysical techniques, and model development and testing. The information and expertise developed from these and previous studies will allow the US Geological Survey to provide sound technical assistance to State low-level waste compacts, the Department of Energy, the Nuclear Regulatory Commission, and the Environmental Protection Agency. 11 references

National Low-Level Waste Management Program Radionuclide Report Series

International Nuclear Information System (INIS)

Rudin, M.J.; Garcia, R.S.

1992-02-01

This volume serves as an introduction to the National Low-Level Radioactive Waste Management Program Radionuclide Report Series. This report includes discussions of radionuclides listed in Title 10 of the Code of Federal Regulations Part 61.55, Tables 1 and 2 (including alpha-emitting transuranics with half-lives greater than five years). Each report includes information regarding radiological and chemical characteristics of specific radionuclides. Information is also included discussing waste streams and waste forms that may contain each radionuclide, and radionuclide behavior in the environment and in the human body. Not all radionuclides commonly found at low-level radioactive waste sites are included in this report. The discussion in this volume explains the rationale of the radionuclide selection process

Elementary study on γ analysis software for low level measurement

International Nuclear Information System (INIS)

Ruan Guanglin; Huang Xianguo; Xing Shixiong

2001-01-01

The difficulty in using fashion γ analysis software in low level measurement is discussed. The ROI report file of ORTEC operation system has been chosen as interface file to write γ analysis software for low-level measurement. The author gives software flowchart and applied example and discusses the existent problems

Level Densities in the actinide region and indirect n,y cross section measurements using the surrogate method

Directory of Open Access Journals (Sweden)

Wiedeking M.

2012-02-01

Full Text Available Results from a program of measurements of level densities and gamma ray strength functions in the actinide region are presented. Experiments at the Oslo cyclotron involving the Cactus/Siri detectors and 232Th(d,x and 232Th(3He,x reactions were carried out to help answer the question of which level density model is the most appropriate for actinide nuclei, since it will have an impact on cross section calculations important for reactor physics simulations. A new technique for extracting level densities and gamma ray strength functions from particle-gamma coincidence data is proposed and results from the development of this technique are presented. In addition, simultaneous measurements of compound nuclear gamma decay probabilities have been performed for the key thorium cycle nuclei 233Th, 231Th and 232Pa up to around 1MeV above the neutron binding energy and have enabled extraction of indirect neutron induced capture cross sections for the 232Th, 231Pa and 230Th nuclei using the surrogate reaction method. Since the neutron capture cross section for 232Th is already well known from direct measurements a comparison provides a stringent test of the applicability of the surrogate technique in the actinide region.

Measuring Satisfaction in the Program Manager, Procuring Contracting Officer Relationship

National Research Council Canada - National Science Library

Gray, John

1997-01-01

.... To comply with this Executive Order, Navy contracting offices require an effective methodology for developing an instrument to measure the satisfaction of their customers, Navy Program Managers...

Community-level moderators of a school-based childhood sexual assault prevention program.

Science.gov (United States)

Morris, Matthew C; Kouros, Chrystyna D; Janecek, Kim; Freeman, Rachel; Mielock, Alyssa; Garber, Judy

2017-01-01

Childhood sexual abuse (CSA) is highly prevalent and associated with a wide variety of negative mental and physical health outcomes. School-based CSA education and prevention programs have shown promise, but it is unclear to what extent community-level characteristics are related to their effectiveness. The present cluster randomized controlled trial evaluated community-level moderators of the Safe@Lastprogramcomparedtoawaitlistcontrolcondition.(*) Knowledge gains from pre- to post-intervention were assessed in 5 domains: safe versus unsafe people; safe choices; problem-solving; clear disclosure; and assertiveness. Participants were 1177 students (46% White, 26% African American, 15% Hispanic, 4% Asian American, 6% Other) in grades 1 through 6 from 14 public schools in Tennessee. Multilevel models accounting for the nesting of children within schools revealed large effect sizes for the intervention versus control across all knowledge domains (d's ranged from 1.56 to 2.13). The effectiveness of the program was moderated by mean per capita income and rates of substantiated cases of child abuse and neglect in the community. Intervention effects were stronger for youth living in lower as compared to higher income counties, and for youth attending schools in counties with lower as compared to higher abuse/neglect rates. Child characteristics (sex, race) did not moderate intervention effects. This research identified two community-level factors that predicted the effectiveness of a CSA education and prevention program designed to improve children's knowledge of personal safety skills. School-based CSA prevention programs may require modification for communities with higher rates of child abuse and neglect. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of knowledge building program concerning about high-level radioactive waste disposal

International Nuclear Information System (INIS)

Kimura, Hiroshi; Yamada, Kazuhiro; Takase, Hiroyasu

2005-01-01

Acquirement of knowledge about the high-level radioactive waste (HLW) disposal is one of the important factors for public to determine the social acceptance of HLW disposal. However in Japan, public do not have knowledge about HLW and its disposal sufficiently. In this work, we developed the knowledge building program concerning about HLW disposal based on Nonaka, and Takeuchi's SECI spiral model in knowledge management, and carried to the experiment on this program. In the results, we found that the participants' knowledge about the HLW disposal increased and changed from misunderstanding' or 'assuming' to 'facts' or 'consideration' through this experimental program. These results said that the experimental program leads participants to have higher quality of knowledge about the HLW disposal. In consequence, this knowledge building program may be effective in the acquirement of high quality knowledge. (author)

Teaching Joint-Level Robot Programming with a New Robotics Software Tool

Directory of Open Access Journals (Sweden)

Fernando Gonzalez

2017-12-01

Full Text Available With the rising popularity of robotics in our modern world there is an increase in the number of engineering programs that offer the basic Introduction to Robotics course. This common introductory robotics course generally covers the fundamental theory of robotics including robot kinematics, dynamics, differential movements, trajectory planning and basic computer vision algorithms commonly used in the field of robotics. Joint programming, the task of writing a program that directly controls the robot’s joint motors, is an activity that involves robot kinematics, dynamics, and trajectory planning. In this paper, we introduce a new educational robotics tool developed for teaching joint programming. The tool allows the student to write a program in a modified C language that controls the movement of the arm by controlling the velocity of each joint motor. This is a very important activity in the robotics course and leads the student to gain knowledge of how to build a robotic arm controller. Sample assignments are presented for different levels of difficulty.

Optimal blood glucose level control using dynamic programming based on minimal Bergman model

Science.gov (United States)

Rettian Anggita Sari, Maria; Hartono

2018-03-01

The purpose of this article is to simulate the glucose dynamic and the insulin kinetic of diabetic patient. The model used in this research is a non-linear Minimal Bergman model. Optimal control theory is then applied to formulate the problem in order to determine the optimal dose of insulin in the treatment of diabetes mellitus such that the glucose level is in the normal range for some specific time range. The optimization problem is solved using dynamic programming. The result shows that dynamic programming is quite reliable to represent the interaction between glucose and insulin levels in diabetes mellitus patient.

Lifetime measurement of the 8s level in francium

International Nuclear Information System (INIS)

Gomez, E.; Sprouse, G.D.; Orozco, L.A.; Galvan, A. Perez

2005-01-01

We measure the lifetime of the 8s level of 210 Fr atoms on a magneto-optically trapped sample with time-correlated single-photon counting. The 7P 1/2 state serves as the resonant intermediate level for two-step excitation of the 8s level completed with a 1.3-μm laser. Analysis of the fluorescence decay through the 7P 3/2 level gives 53.30±0.44 ns for the 8s level lifetime

SPSS programs for the measurement of nonindependence in standard dyadic designs.

Science.gov (United States)

Alferes, Valentim R; Kenny, David A

2009-02-01

Dyadic research is becoming more common in the social and behavioral sciences. The most common dyadic design is one in which two persons are measured on the same set of variables. Very often, the first analysis of dyadic data is to determine the extent to which the responses of the two persons are correlated-that is, whether there is nonindependence in the data. We describe two user-friendly SPSS programs for measuring nonindependence of dyadic data. Both programs can be used for distinguishable and indistinguishable dyad members. Inter1.sps is appropriate for interval measures. Inter2.sps applies to categorical variables. The SPSS syntax and data files related to this article may be downloaded as supplemental materials from brm.psychonomic-journals.org/content/supplemental.

Low-level waste (LLW) reclamation program for the Point Lepreau Solid Radioactive Waste Management Facility (SRWMF)

International Nuclear Information System (INIS)

Mersereau, M.; McIntyre, K.

2006-01-01

Low level radioactive waste retrieved from intermediate storage vaults at Point Lepreau Generating Station has been sorted to remove the non-radioactive portion. The program began with trials to validate procedures and equipment, followed by a production run that is on-going. Waste boxes are opened and sorted at a ventilated sorting table. The sorted waste is directed to the station's free-release ('Likely Clean') waste stream or to the radioactive waste stream, depending on activity measurements. The radioactive waste content of the sorted materials has been reduced by 96% (by mass) using this process. (author)

Low-level waste (LLW) reclamation program for the Point Lepreau Solid Radioactive Waste Management Facility (SRWMF)

Energy Technology Data Exchange (ETDEWEB)

Mersereau, M.; McIntyre, K. [Point Lepreau Generating Station, Lepreau, New Brunswick (Canada)]. E-mail: MMersereau@nbpower.com; KMcIntyre@nbpower.com

2006-07-01

Low level radioactive waste retrieved from intermediate storage vaults at Point Lepreau Generating Station has been sorted to remove the non-radioactive portion. The program began with trials to validate procedures and equipment, followed by a production run that is on-going. Waste boxes are opened and sorted at a ventilated sorting table. The sorted waste is directed to the station's free-release ('Likely Clean') waste stream or to the radioactive waste stream, depending on activity measurements. The radioactive waste content of the sorted materials has been reduced by 96% (by mass) using this process. (author)

Effects of venting on wind noise levels measured at the eardrum.

Science.gov (United States)

Chung, King

2013-01-01

Wind noise can be a nuisance to hearing aid users. With the advent of sophisticated feedback reduction algorithms, people with higher degrees of hearing loss are fit with larger vents than previously allowed, and more people with lesser degrees of hearing loss are fit with open hearing aids. The purpose of this study was to examine the effects of venting on wind noise levels in the ear canal for hearing aids with omnidirectional and directional microphones. Two behind-the-ear hearing aids were programmed when they were worn on a Knowles Electronics Manikin for Acoustic Research. The hearing aid worn on the right ear was programmed to the omnidirectional microphone mode and the one on the left to the directional microphone mode. The hearing aids were adjusted to linear amplification with flat frequency response in an anechoic chamber. Gains below 10 dB were used to avoid output limiting of wind noise levels at low input levels. Wind noise samples were recorded at the eardrum location in a wind tunnel at wind velocities ranging from a gentle to a strong breeze. The hearing aids were coupled to #13 tubings (i.e., open vent), or conventional skeleton earmolds with no vent, pressure vents, or 3mm vents. Polar and spectral characteristics of wind noise were analyzed off-line using MatLab programs. Wind noise levels in the ear canals were mostly predicted by vent-induced frequency response changes in the conventional earmold conditions for both omnidirectional and directional hearing aids. The open vent condition, however, yielded the lowest levels, which could not be entirely predicted by the frequency response changes of the hearing aids. This indicated that a wind-related vent effect permitted an additional amount of sound reduction in the ear canal, which could not be explained by known vent effects. For the microphone location, form factor, and gain settings tested, open fit hearing aids yielded lower noise levels at the eardrum location than conventional behind

DOE Low-Level Waste Management Program perspective on technology transfer: opportunities and challenges

International Nuclear Information System (INIS)

Large, D.E.

1982-01-01

The Department of Energy's Low-Level Waste Management Program (DOE LLWMP) perspective in regard to transfer of LLWMP technology to current and potential users in both the commercial and defense sectors is discussed. Past, present, and future opportunities and challenges for the whole nuclear waste management are indicated. Elements considered include: historical and evolutionary events and activities; the purpose of the Program and its inherent opportunities and challenges; achievements and expected accomplishments; supporters and interactors; packaging and delivering technology; implementing and serving potential users; determining and meeting users' needs; and identifying and responding to opportunities and challenges. The low-level waste management effort to improve shallow land burial technology began in FY 1977 and has expanded to include waste treatment and alternative disposal methods. Milestones have been established and are used as principal management control items. This technology, the Program Product, is described and is made available. This year, the Program has drafted criteria for inclusion in a DOE order for radioactive waste management operations at DOE sites

Measuring progress of the global sea level observing system

Science.gov (United States)

Woodworth, Philip L.; Aarup, Thorkild; Merrifield, Mark; Mitchum, Gary T.; Le Provost, Christian

Sea level is such a fundamental parameter in the sciences of oceanography geophysics, and climate change, that in the mid-1980s, the Intergovernmental Oceanographic Commission (IOC) established the Global Sea Level Observing System (GLOSS). GLOSS was to improve the quantity and quality of data provided to the Permanent Service for Mean Sea Level (PSMSL), and thereby, data for input to studies of long-term sea level change by the Intergovernmental Panel on Climate Change (IPCC). It would also provide the key data needed for international programs, such as the World Ocean Circulation Experiment (WOCE) and later, the Climate Variability and Predictability Programme (CLIVAR).GLOSS is now one of the main observation components of the Joint Technical Commission for Oceanography and Marine Meteorology (JCOMM) of IOC and the World Meteorological Organization (WMO). Progress and deficiencies in GLOSS were presented in July to the 22nd IOC Assembly at UNESCO in Paris and are contained in the GLOSS Assessment Report (GAR) [IOC, 2003a].

Paratingent Derivative Applied to the Measure of the Sensitivity in Multiobjective Differential Programming

Directory of Open Access Journals (Sweden)

F. García

2013-01-01

Full Text Available We analyse the sensitivity of differential programs of the form subject to where and are maps whose respective images lie in ordered Banach spaces. Following previous works on multiobjective programming, the notion of -optimal solution is used. The behaviour of some nonsingleton sets of -optimal solutions according to changes of the parameter in the problem is analysed. The main result of the work states that the sensitivity of the program is measured by a Lagrange multiplier plus a projection of its derivative. This sensitivity is measured by means of the paratingent derivative.

Level validity of self-report whole-family measures.

Science.gov (United States)

Manders, Willeke A; Cook, William L; Oud, Johan H L; Scholte, Ron H J; Janssens, Jan M A M; De Bruyn, Eric E J

2007-12-01

This article introduces an approach to testing the level validity of family assessment instruments (i.e., whether a family instrument measures family functioning at the level of the system it purports to assess). Two parents and 2 adolescents in 69 families rated the warmth in each of their family relationships and in the family as a whole. Family members' ratings of whole-family warmth assessed family functioning not only at the family level (i.e., characteristics of the family as a whole) but also at the individual level of analysis (i.e., characteristics of family members as raters), indicating a lack of level validity. Evidence was provided for the level validity of a latent variable based on family members' ratings of whole-family warmth. The findings underscore the importance of assessing the level validity of individual ratings of whole-family functioning.

Estimating Bandwidth Requirements using Flow-level Measurements

NARCIS (Netherlands)

Bruyère, P.; de Oliveira Schmidt, R.; Sperotto, Anna; Sadre, R.; Pras, Aiko

Bandwidth provisioning is an important task of network management and it is done aiming to meet desired levels of quality of service. Current practices of provisioning are mostly based on rules-of-thumb and use coarse traffic measurements that may lead to problems of under and over dimensioning of

Military Personnel: Performance Measures Needed to Determine How Well DOD’s Credentialing Program Helps Servicemembers

Science.gov (United States)

2016-10-01

MILITARY PERSONNEL Performance Measures Needed to Determine How Well DOD’s Credentialing Program Helps Servicemembers...Measures Needed to Determine How Well DOD’s Credentialing Program Helps Servicemembers What GAO Found The Department of Defense (DOD) has taken steps to...establish the statutorily required credentialing program, but it has not developed performance measures to gauge the program’s effectiveness

Mutual inductance appliance for measuring the level of a molten metal

International Nuclear Information System (INIS)

Zbinden, Marc.

1982-01-01

The invention concerns an appliance for measuring the level of a molten metal of the kind using the variation of the mutual inductance between two imbricated windings depending on the level of the free area of the molten metal in the range of levels taken up by the windings. It has a particularly significant use in measuring the level of liquid sodium, especially in nuclear facilities where sodium is used as coolant [fr

Effectiveness of Human Research Protection Program Performance Measurements.

Science.gov (United States)

Tsan, Min-Fu; Nguyen, Yen

2017-10-01

We analyzed human research protection program performance metric data of all Department of Veterans Affairs research facilities obtained from 2010 to 2016. Among a total of 25 performance metrics, 21 (84%) showed improvement, four (16%) remained unchanged, and none deteriorated during the study period. The overall improvement from these 21 performance metrics was 81.1% ± 18.7% (mean ± SD), with a range of 30% to 100%. The four performance metrics that did not show improvement all had initial noncompliance/incidence rates of performance metrics that showed improvement ranged from 0.05% to 60%. However, of the 21 performance metrics that showed improvement, 10 had initial noncompliance/incidence rates of performance measurement is an effective tool in improving the performance of human research protection programs.

Design and Assessment of an Associate Degree-Level Plant Operations Technical Education Program

Science.gov (United States)

Selwitz, Jason Lawrence

Research was undertaken to develop and evaluate an associate degree-level technical education program in Plant Operations oriented towards training students in applied science, technology, engineering, and mathematics (STEM) skills and knowledge relevant to a spectrum of processing industries. This work focuses on four aspects of the curriculum and course development and evaluation research. First, the context of, and impetus for, what was formerly called vocational education, now referred to as technical or workforce education, is provided. Second, the research that was undertaken to design and evaluate an associate degree-level STEM workforce education program is described. Third, the adaptation of a student self-assessment of learning gains instrument is reviewed, and an analysis of the resulting data using an adapted logic model is provided, to evaluate the extent to which instructional approaches, in two process control/improvement-focused courses, were effective in meeting course-level intended learning outcomes. Finally, eight integrative multiscale exercises were designed from two example process systems, wastewater treatment and fast pyrolysis. The integrative exercises are intended for use as tools to accelerate the formation of an operator-technician's multiscale vision of systems, unit operations, underlying processes, and fundamental reactions relevant to multiple industries. Community and technical colleges serve a vital function in STEM education by training workers for medium- and high-skilled technical careers and providing employers the labor necessary to operate and maintain thriving business ventures. Through development of the curricular, course, and assessment-related instruments and tools, this research helps ensure associate degree-level technical education programs can engage in a continual process of program evaluation and improvement.

Effect of an individualized physical training program on resting cortisol and growth hormone levels and fat oxidation during exercise in obese children.

Science.gov (United States)

Ben Ounis, O; Elloumi, M; Zouhal, H; Makni, E; Lac, G; Tabka, Z; Amri, M

2011-02-01

The aim of this study was to characterize the resting levels of cortisol and growth hormone (GH), and the substrate profile during exercise of obese children before and after an individualized training program. Twenty-two obese children (13.1 ± 0.8 yrs) were included in the study. Twelve individuals (six boys and six girls; 31.1 ± 1.1 kg/m², VO₂(peak)=1.92 ± 0.16l/min) participated in a two-month endurance training program and 10 individuals (five boys and five girls; 30.9 ± 1.7 kg/m², VO₂(peak)=1.98 ± 0.12l/min) served as controls. Training was individualized and targeting at the point were fat oxidation was maximal (Lipox(max)). Substrate oxidation was evaluated by indirect calorimetry. To determine plasma cortisol and GH concentrations, blood was collected at rest before and after the two-month period. Before the program, no significant differences were detected between the training group and the control group for any of the measured anthropometric, metabolic or hormonal variables. At the end of the two-month program, training group showed an increase in VO₂(peak) and fat oxidation during exercise. After the program, resting levels of GH and cortisol were significantly increased in the training group (+0.9 ± 0.3 ng/mL and +55.4 ± 10.3 ng/mL respectively, p levels of GH and cortisol. Copyright © 2010 Elsevier Masson SAS. All rights reserved.

Satellite data sets for the atmospheric radiation measurement (ARM) program

Energy Technology Data Exchange (ETDEWEB)

Shi, L.; Bernstein, R.L. [SeaSpace Corp., San Diego, CA (United States)

1996-04-01

This abstract describes the type of data obtained from satellite measurements in the Atmospheric Radiation Measurement (ARM) program. The data sets have been widely used by the ARM team to derive cloud-top altitude, cloud cover, snow and ice cover, surface temperature, water vapor, and wind, vertical profiles of temperature, and continuoous observations of weather needed to track and predict severe weather.

Vitamin A Supplementation Programs and Country-Level Evidence of Vitamin A Deficiency

Directory of Open Access Journals (Sweden)

James P. Wirth

2017-02-01

Full Text Available Vitamin A supplementation (VAS programs targeted at children aged 6–59 months are implemented in many countries. By improving immune function, vitamin A (VA reduces mortality associated with measles, diarrhea, and other illnesses. There is currently a debate regarding the relevance of VAS, but amidst the debate, researchers acknowledge that the majority of nationally-representative data on VA status is outdated. To address this data gap and contribute to the debate, we examined data from 82 countries implementing VAS programs, identified other VA programs, and assessed the recentness of national VA deficiency (VAD data. We found that two-thirds of the countries explored either have no VAD data or data that were >10 years old (i.e., measured before 2006, which included twenty countries with VAS coverage ≥70%. Fifty-one VAS programs were implemented in parallel with at least one other VA intervention, and of these, 27 countries either had no VAD data or data collected in 2005 or earlier. To fill these gaps in VAD data, countries implementing VAS and other VA interventions should measure VA status in children at least every 10 years. At the same time, the coverage of VA interventions can also be measured. We identified three countries that have scaled down VAS, but given the lack of VA deficiency data, this would be a premature undertaking in most countries without appropriate status assessment. While the global debate about VAS is important, more attention should be directed towards individual countries where programmatic decisions are made.

Program evaluation: Weatherization Residential Assistance Partnership (WRAP) Program. Volume 1, Final report

Energy Technology Data Exchange (ETDEWEB)

1991-12-01

The Connecticut low income weatherization program was developed in response to a 1987 rate docket order from the Connecticut Department of Public Utility Control (DPUC) to Connecticut Light & Power Co., an operating subsidiary of Northeast Utilities (NU). (Throughout this report, NU is referred to as the operator of the program.) This program, known as the Weatherization Residential Assistance Partnership, or WRAP, was configured utilizing input from a collaborative group of interested parties to the docket. It was agreed that this program would be put forth by the electric utility, but would not ignore oil and gas savings (thus, it was to be ``fuel- blind``). The allocated cost of conservation services for each fuel source, however, should be cost effective. It was to be offered to those utility customers at or below 200 percent of the federal poverty levels, and provide a wide array of energy saving measures directed toward heating, water heating and lighting. It was felt by the collaborative group that this program would raise the level of expenditures per participant for weatherization services provided by the state, and by linking to and revising the auditing process for weatherization, would lower the audit unit cost. The program plans ranged from the offering of low-cost heating, water heating and infiltration measures, increased insulation levels, carpentry and plumbing services, to furnace or burner replacement. The program was configured to allow for very comprehensive weatherization and heating system servicing.

Effects of microelectronics on industrial level measuring

International Nuclear Information System (INIS)

Schaudel, D.E.

1979-01-01

Microelectronic elements and production technologies have begun to change industrial level measurement, and this trend will continue. Spectacular breakthroughs cannot be expected, due to the major demand of reliability and to administrative constraints. The demand for transducers has increased with the advance of low-cost computer hardware. Electronics makes well-known method of measurements more universally applicable; it helps to realize new methods, and to design multifunctional transducers which always give the necessary signal for process guidance. The effects on society and environment are wholly positive: More and better measuring technologies permit a better utilisation of raw materials and energies, help to prevent environmental damage, and to raise the standard of living. Negative results are not to be expected on this sector. (orig./RW) [de

Global change and the measurement of absolute sea-level

Science.gov (United States)

Diamante, John M.; Pyle, Thomas E.; Carter, William E.; Scherer, Wolfgang

To quantify properly the long-term response of sea-level to climate change, land motions must be separated from the apparent or relative sea-level change recorded by conventional tide/sea-level gauges. Here we present a concept for global measurement of the true or “absolute” sea-level change, which combines recent advances in space-based geodetic techniques with plans for a global sea-level network under the World Climate Research Programme (WCRP). Data from initial feasibility tests show that land motion, due to global (plate tectonic), regional (glacial rebound), or local (fluid withdrawal) effects, can probably be measured to ±1cm (on a single measurement basis) by an innovative combination of Very Long Baseline Interferometry (VLBI) and Global Positioning System (GPS) tevhniques. By making repeated observations of position at a number of tide gauges using portable, economical GPS receivers in a differential mode relative to the fewer, more stable, but more expensive VLBI observatories, it will be possible to subtract land motion from the relative sea-level signal. Decadal to century scale trends at the 1-2mm y -1 level will be resolvable in the sea-level and vertical land motion time series within about a decade. Detection of subsidence or uplift at specific gauges will allow correction for land motion or deletion of bad data when computing regional or global, i.e. eustatic, sea-level changes. In addition to their applications in oceanography and climate studies, such data will test models by Peltier and other that relate mantle viscosity and deglaciation history to present rates of crustal subsidence or uplift. If the predicted crustal motions are confirmed, we can also have more confidence in the use of historical tide/sea-level gauge records in retrospective studies of sea-level change related to climate variability on decadal or longer time scales. It is concluded that as few as one-third (about 100) of the total number of tide/sea-level gauges (250

Relating measurement invariance, cross-level invariance, and multilevel reliability

NARCIS (Netherlands)

Jak, S.; Jorgensen, T.D.

2017-01-01

Data often have a nested, multilevel structure, for example when data are collected from children in classrooms. This kind of data complicate the evaluation of reliability and measurement invariance, because several properties can be evaluated at both the individual level and the cluster level, as

Skylab experiments. Volume 6: Mechanics. [Skylab program accomplishments for high school level education

Science.gov (United States)

1973-01-01

Skylab program activities are presented in a form adapted to instruction of high school students. The overall goals of the program are discussed. The specific accomplishments of the mechanics investigations are described. The subjects involved are as follows: (1) evaluation of mobility aids, (2) mass measurement devices, and (3) space guidance crew/vehicle disturbances.

Effects of a short-term exercise training program on aerobic fitness, fatigue, health perception and activity level of subjects with multiple sclerosis.

Science.gov (United States)

Mostert, S; Kesselring, J

2002-04-01

Multiple sclerosis (MS) patients of an inpatient rehabilitation program have been randomly assigned to an exercise training (MS-ET) or nontraining group (MS-NI). Before and after 4 weeks of aerobic exercise training, a graded maximal exercise test with measurement of gas exchange and a lung function test was administered to all 26 patients fulfilling the inclusion criteria. Activity level, fatigue and health perception were measured by means of questionnaires. Twenty-six healthy persons served as control group and were matched in respect of age, gender and activity level. Training intervention consisted of 5x30 min sessions per week of bicycle exercise with individualised intensity. Compared with baseline, the MS training group demonstrated a significant rightward placement of the aerobic threshold (AT) (VO2+13%; work rate [WR])+11%), an improvement of health perception (vitality+46%; social interaction+36%), an increase of activity level (+17%) and a tendency to less fatigue. No changes were observed for the MS-NI group and the control groups. Maximal aerobic capacity and lung function were not changed by either training or nontraining in all four groups. Overall compliance to the training program was quite low (65%), whereas incidence of symptom exacerbation by physical activity has been lower than expected (6%).

International program: Feasibility of the evacuation of high-level radioactive wastes under the ocean depths. (Seabed Program)

International Nuclear Information System (INIS)

Barbreau, A.

1990-01-01

The Seabed feasibility program is an international scientific program of research on the feasibility of the disposal of high-level radioactive wastes into the geological formations making up the floor of the great abyssal plains of the oceans. Decided in 1977, the program is aimed at answering the three following questions: 1) are there potentially favourable sites. 2) is the disposal of wastes possible. 3) does the operation present safety guarantees. First initiated by four countries (USA, UK, Japan and France), the program sponsored by the OECD nuclear energy agency was gathering ten countries and the Commission of the European communities in 1988. The techniques of waste disposal by means of drilling in consolidated sediments and penetrators in loose sediments have been studied. The penetrator technique has been the most thoroughly studied, especially through in situ experiments in the Atlantic ocean. The various factors affecting safety have been studied and the radiological consequences of a burial operation assessed through models. It has been concluded that such an operation could be carried out technically under quite satisfying conditions [fr

Estimating retained gas volumes in the Hanford tanks using waste level measurements

International Nuclear Information System (INIS)

Whitney, P.D.; Chen, G.; Gauglitz, P.A.; Meyer, P.A.; Miller, N.E.

1997-09-01

The Hanford site is home to 177 large, underground nuclear waste storage tanks. Safety and environmental concerns surround these tanks and their contents. One such concern is the propensity for the waste in these tanks to generate and trap flammable gases. This report focuses on understanding and improving the quality of retained gas volume estimates derived from tank waste level measurements. While direct measurements of gas volume are available for a small number of the Hanford tanks, the increasingly wide availability of tank waste level measurements provides an opportunity for less expensive (than direct gas volume measurement) assessment of gas hazard for the Hanford tanks. Retained gas in the tank waste is inferred from level measurements -- either long-term increase in the tank waste level, or fluctuations in tank waste level with atmospheric pressure changes. This report concentrates on the latter phenomena. As atmospheric pressure increases, the pressure on the gas in the tank waste increases, resulting in a level decrease (as long as the tank waste is open-quotes softclose quotes enough). Tanks with waste levels exhibiting fluctuations inversely correlated with atmospheric pressure fluctuations were catalogued in an earlier study. Additionally, models incorporating ideal-gas law behavior and waste material properties have been proposed. These models explicitly relate the retained gas volume in the tank with the magnitude of the waste level fluctuations, dL/dP. This report describes how these models compare with the tank waste level measurements

Importance of measuring lactate levels in children with sepsis.

Science.gov (United States)

Anil, Nisha

2017-10-10

Sepsis is a major public health problem as well as one of the leading causes of preventable death in children because of failure to recognise the early signs and symptoms and to resuscitate rapidly. Blood lactate levels are used to assess the severity of sepsis and the effectiveness of resuscitation. Lactate levels are easily obtainable and should be checked in all patients admitted with suspected sepsis within six hours of presentation. The test should be repeated four and eight-hours post-diagnosis of sepsis. For the diagnosis of sepsis, patients' clinical symptoms, along with the combined analysis of partial pressure of oxygen, carbon dioxide and lactate levels, should be used. A multitude of factors can cause elevated lactate levels and so clinicians should use elevated levels cautiously by considering all other aetiologies. This article, which focuses on practice in Australia but makes reference to the UK, discusses the importance of measuring lactate levels in sepsis, the pathophysiology of lactate production, causes of elevated lactate levels, lactate measurement, nursing management of patients with elevated lactate levels, limitations of using lactate as a biomarker for diagnosing sepsis and implications for practice. ©2012 RCN Publishing Company Ltd. All rights reserved. Not to be copied, transmitted or recorded in any way, in whole or part, without prior permission of the publishers.

Facilitators for the development and implementation of health promoting policy and programs – a scoping review at the local community level

Directory of Open Access Journals (Sweden)

Daniel Weiss

2016-02-01

Full Text Available Abstract Background Health promotion, with a focus on multidimensional upstream factors and an ecological, life-course approach, is establishing itself as the guiding philosophy for addressing public health. Action at the political and programmatic level on the Social Determinants of Health has proven effective for promoting and building public health at all levels but has been particularly evident at the national and international levels – due in large part to available documents and guidelines. Although research and experience establish that health promotion is most effective when settings-based, the development of health promoting policies and programs at the local level is still difficult. This study intended to investigate available knowledge on the development and implementation of health promoting policies and programs at the local level and identify factors most important for facilitating capacity building and outcome achievement. Methods We used a scoping review in order to review the current literature on local policy development and program implementation. Keywords were chosen based on results of a previous literature review. A total of 53 articles were divided into two categories: policy and implementation. Critical analysis was conducted for each article and a summary assembled. Data was charted with specific focus on the aims of the study, data acquisition, key theories/concepts/frameworks used, outcome measures, results, and conclusions. Results The articles included in this study primarily focused on discussing factors that facilitate the development of health promoting policy and the implementation of health promotion programs. Most significant facilitators included: collaborative decision-making, agreement of objectives and goals, local planning and action, effective leadership, building and maintaining trust, availability of resources, a dynamic approach, a realistic time-frame, and trained and knowledgeable staff. Within

Unibert - PC software for radiometric level gauging - the LB440 measuring system

International Nuclear Information System (INIS)

Mann, H.; Bickert, M.

2001-01-01

In almost all industrial branches radiometric measuring systems are being used today for a lot of different tasks. The most common field of this application are level gauging measurements by use of gamma radiation, i.e. for level detection as well as for level gauging over ranges of up to several meters. For our level gauge measuring system LB440 we developed a clearly arranged PC software, which allows starting, measuring and service of the level gauge. Over the RS232-interface the industrial computer can be connected with a Laptop or PC. The software is a supplemental or even a substitute for the operation over the frontpanel. The measuring system can be completely controlled by the Unibert PC-Software, realised by LabVIEW 5.1.1, which offers an interactive graphical user interface. The same functionality as in the ''embedded - software'' is available, completed with some additional functions. (orig.) [de

Development of a measure of training program effectiveness for nuclear power plants

International Nuclear Information System (INIS)

Connelly, E.M.; Haas, P.; VanHemel, S.B.; Wreathall, J.

1991-01-01

The approach taken to develop measures of training program effectiveness recognizes that many subject matter experts (SMEs) with varying viewpoints on training effectiveness are working to insure nuclear power plant (NPP) safety. This paper discusses a model as the effectiveness rating strategies of various SMEs whose ratings are important to training; i.e., build a measure of effectiveness (MOE) representing the rating strategy of a sample of those SMEs. A quantitative model of these assessment strategies permits a broad review of them by ll interested parties and provides the basis for building a broadly accepted training program MOE. Major differences in assessment strategies can be examined to determine whether they are appropriate to the different points of view or are in conflict. This paper describes the basic concepts of building effectiveness measures, the methodology used to build the measures, a summary of the measures developed form NRC and industry sources, and an analysis of the differences among SMEs' measures

Cernavoda NPP Unit 1: Operating experience program and plant specific performance indicators (level 2)

International Nuclear Information System (INIS)

Teodor, Vasile; Popa, Viorel

1998-01-01

The basis for the Operating Experience Program was set in place since early stages of the commissioning phase (1993), when a system based on the Canadian approach was implemented for reporting, reviewing, assessing and establishing of the necessary corrective action for unplanned events. This system provided excellent opportunity to train staff in unplanned event assessment methodology, and prepare the station for the formal reporting process following criticality in accordance with the licensing requirements. The formal process, set in place after criticality is described in Station Instruction Procedure SI-01365-P13 'Unplanned Event Report' and was developed under the supervision of Safety and Compliance Department. In parallel, a program for information exchange and trending of performance indicators was developed by Technical Services Department. The WANO recommendations following August 1997 Peer Review provided the opportunity for a better understanding and reconsideration of the Operating Experience Program. As a result, all the activities related to this topic were assigned to a new structure, within Safety and Compliance Department. As such an Operating Experience Group was created and a new program is now being developed in an integrated and centralized manner. The content of the paper is the following: - Overview; - Operating Experience Program; - Event Analysis (Unplanned Events Assessment System - UEIR Process- and Systematic Analysis of Operational Events - ACR Process); - Information Exchange Program; - Monitoring of Operating Experience - Plant Specific Performance Indicators; - Purpose; - Level 2 Performance Indicators. Four appendices are added containing: - A. Station performance indicators/targets (Level 2); - B. SPI (Station Performance Indicators - Level 2) - Graphics; - C. UEIR, LRS (Safety and Licensing Review Sheet), UEFR (Unplanned Event Follow-up Report), ACR and OPEX forms. (authors)

High-level Programming and Symbolic Reasoning on IoT Resource Constrained Devices

Directory of Open Access Journals (Sweden)

Sal vatore Gaglio

2015-05-01

Full Text Available While the vision of Internet of Things (IoT is rather inspiring, its practical implementation remains challenging. Conventional programming approaches prove unsuitable to provide IoT resource constrained devices with the distributed processing capabilities required to implement intelligent, autonomic, and self-organizing behaviors. In our previous work, we had already proposed an alternative programming methodology for such systems that is characterized by high-level programming and symbolic expressions evaluation, and developed a lightweight middleware to support it. Our approach allows for interactive programming of deployed nodes, and it is based on the simple but e ective paradigm of executable code exchange among nodes. In this paper, we show how our methodology can be used to provide IoT resource constrained devices with reasoning abilities by implementing a Fuzzy Logic symbolic extension on deployed nodes at runtime.

Challenges in Measuring Benefit of Clinical Research Training Programs--the ASH Clinical Research Training Institute Example.

Science.gov (United States)

Sung, Lillian; Crowther, Mark; Byrd, John; Gitlin, Scott D; Basso, Joe; Burns, Linda

2015-12-01

The American Society of Hematology developed the Clinical Research Training Institute (CRTI) to address the lack of training in patient-oriented research among hematologists. As the program continues, we need to consider metrics for measuring the benefits of such a training program. This article addresses the benefits of clinical research training programs. The fundamental and key components are education and mentorship. However, there are several other benefits including promotion of collaboration, job and advancement opportunities, and promotion of work-life balance. The benefits of clinical research training programs need to be measured so that funders and society can judge if they are worth the investment in time and resources. Identification of elements that are important to program benefit is essential to measuring the benefit of the program as well as program planning. Future work should focus on the constructs which contribute to benefits of clinical research training programs such as CRTI.

From Knowledge to Action: Tips for Encouraging and Measuring Program-Related Behavior Change

Science.gov (United States)

Chazdon, Scott; Horntvedt, Jody; Templin, Elizabeth

2016-01-01

It is challenging to document the behavior changes that result from Extension programming. This article describes an evaluation method we call the "action items method." Unlike other approaches for measuring behavior change, this method requires program participants to define their own action plans as part of a program and then asks them…

Noaa chlorofluorocarbon tracer program air and seawater measurements: 1986-1989. Data file

International Nuclear Information System (INIS)

Wisegarver, D.P.; Bullister, J.L.; Gammon, R.H.; Menzia, F.A.; Kelly, K.C.

1993-04-01

The NOAA Chlorofluorocarbon (CFC) Tracer Program at PMEL has been measuring the growing burden of these anthropogenic gases in the thermocline waters of the Pacific Ocean since 1980. The central goals of the NOAA CFC Tracer Program are to document the transient invasion of the CFC tracers into the Pacific Ocean, by means of repeat occupations of key hydrographic sections at 5-year intervals, and to interpret these changing distributions in terms of coupled ocean-atmosphere models. Studies are underway to use the CFC observations in model-validation studies, and to help develop predictive capabilities on the decade-to-century timescale. The report includes measurements of trichlorofluoromethane (CFC-11) and dichlorodifluoromethane (CFC-12) dissolved in seawater samples collected in the Pacific Ocean by the NOAA CFC Tracer Program on six cruises during the period of 1986-1989. Measurements of depth, pressure, salinity, temperature, and dissolved oxygen are included with the CFC data. Measurements of CFC-11 and CFC-12 in air samples collected along the cruise tracks are also included in the report. Data from the report are also available from the authors in digital format

Static and Dynamic Coupling and Cohesion Measures in Object Oriented Programming

OpenAIRE

Vasudha Dixit, Dr. Rajeev Vishwkarma

2013-01-01

A large numbers of metrics have been proposed for measuring properties of object-oriented software such as size, inheritance, cohesion and coupling. The coupling metrics presented in this paper exploring the difference between inheritance and interface programming. This paper presents a measurement to measure coupling between object (CBO), number of associations between classes (NASSocC), number of dependencies in metric (NDepIN) and number of dependenciesout m...

Measurement of Background Gamma Radiation Levels at Two ...

African Journals Online (AJOL)

MICHAEL

ABSTRACT: An in-situ measurement of the background radiation level was carried out at the vicinity of three ... Soil contains small quantities of radioactive elements along with their progeny. .... assessment for soil samples from Kestanbol.

IAEA coordinated research program on the evaluation of solidified high-level radioactive waste products

International Nuclear Information System (INIS)

Grover, J.R.; Schneider, K.J.

1979-01-01

A coordinated research program on the evaluation of solidified high-level radioactive waste products has been active with the IAEA since 1976. The program's objectives are to integrate research and to provide a data bank on an international basis in this subject area. Results and considerations to date are presented

Aspects on Teaching/Learning with Object Oriented Programming for Entry Level Courses of Engineering.

Science.gov (United States)

de Oliveira, Clara Amelia; Conte, Marcos Fernando; Riso, Bernardo Goncalves

This work presents a proposal for Teaching/Learning, on Object Oriented Programming for Entry Level Courses of Engineering and Computer Science, on University. The philosophy of Object Oriented Programming comes as a new pattern of solution for problems, where flexibility and reusability appears over the simple data structure and sequential…

Measurement of integrated flux of cosmic ray muons at sea level using the INO-ICAL prototype detector

International Nuclear Information System (INIS)

Pal, S.; Acharya, B.S.; Majumder, G.; Mondal, N.K.; Samuel, D.; Satyanarayana, B.

2012-01-01

The India-based Neutrino Observatory (INO) collaboration is planning to set-up a magnetized Iron-CALorimeter (ICAL) to study atmospheric neutrino oscillations with precise measurements of oscillations parameters. The ICAL uses 50 kton iron as target mass and about 28800 Resistive Plate Chambers (RPC) of 2 m × 2 m in area as active detector elements. As part of its R and D program, a prototype detector stack comprising 12 layers of RPCs of 1 m × 1 m in area has been set-up at Tata Institute of Fundamental Research (TIFR) to study the detector parameters using cosmic ray muons. We present here a study of muon flux measurement at sea level and lower latitude. (Site latitude: 18°54'N, longitude: 72°48'E.)

Broadening measures of success: results of a behavioral health translational research training program.

Science.gov (United States)

Baldwin, Julie A; Williamson, Heather J; Eaves, Emery R; Levin, Bruce L; Burton, Donna L; Massey, Oliver T

2017-07-24

While some research training programs have considered the importance of mentoring in inspiring professionals to engage in translational research, most evaluations emphasize outcomes specific to academic productivity as primary measures of training program success. The impact of such training or mentoring programs on stakeholders and local community organizations engaged in translational research efforts has received little attention. The purpose of this evaluation is to explore outcomes other than traditional academic productivity in a translational research graduate certificate program designed to pair graduate students and behavioral health professionals in collaborative service-learning projects. Semi-structured qualitative interviews with scholars, community mentors, and academic mentors were conducted regarding a translational research program to identify programmatic impacts. Interviews were transcribed and coded by the research team to identify salient themes related to programmatic outcomes. Results are framed using the Translational Research Impact Scale which is organized into three overarching domains of potential impact: (1) research-related impacts, (2) translational impacts, and (3) societal impacts. This evaluation demonstrates the program's impact in all three domains of the TRIS evaluation framework. Graduate certificate participants (scholars) reported that gaining experience in applied behavioral health settings added useful skills and expertise to their present careers and increased their interest in pursuing translational research. Scholars also described benefits resulting from networks gained through participation in the program, including valuable ties between the university and community behavioral health organizations. This evaluation of the outcomes of a graduate certificate program providing training in translational research highlights the need for more community-oriented and practice-based measures of success. Encouraging practitioner

Measurement quality assurance

International Nuclear Information System (INIS)

Eisenhower, E.H.

1988-01-01

The quality of a radiation protection program can be no better than the quality of the measurements made to support it. In many cases, that quality is unknown and is merely implied on the basis of a calibration of a measuring instrument. If that calibration is inappropriate or is performed improperly, the measurement result will be inaccurate and misleading. Assurance of measurement quality can be achieved if appropriate procedures are followed, including periodic quality control actions that demonstrate adequate performance. Several national measurement quality assurance (MQA) programs are operational or under development in specific areas. They employ secondary standards laboratories that provide a high-quality link between the National Bureau of Standards and measurements made at the field use level. The procedures followed by these secondary laboratories to achieve MQA will be described, as well as plans for similar future programs. A growing general national interest in quality assurance, combined with strong specific motivations for MQA in the area of ionizing radiation, will provide continued demand for appropriate national programs. Such programs must, however, employ procedures that are cost effective and must be developed with participation by all affected parties

Indirect measurement of molten steel level in tundish based on laser triangulation

Science.gov (United States)

Su, Zhiqi; He, Qing; Xie, Zhi

2016-03-01

For real-time and precise measurement of molten steel level in tundish during continuous casting, slag level and slag thickness are needed. Among which, the problem of slag thickness measurement has been solved in our previous work. In this paper, a systematic solution for slag level measurement based on laser triangulation is proposed. Being different from traditional laser triangulation, several aspects for measuring precision and robustness have been done. First, laser line is adopted for multi-position measurement to overcome the deficiency of single point laser range finder caused by the uneven surface of the slag. Second, the key parameters, such as installing angle and minimum requirement of the laser power, are analyzed and determined based on the gray-body radiation theory to fulfill the rigorous requirement of measurement accuracy. Third, two kinds of severe noises in the acquired images, which are, respectively, caused by heat radiation and Electro-Magnetic Interference (EMI), are cleaned via morphological characteristic of the liquid slag and color difference between EMI and the laser signals, respectively. Fourth, as false target created by stationary slag usually disorders the measurement, valid signals of the slag are distinguished from the false ones to calculate the slag level. Then, molten steel level is obtained by the slag level minus the slag thickness. The measuring error of this solution is verified by the applications in steel plants, which is ±2.5 mm during steady casting and ±3.2 mm at the end of casting.

Indirect measurement of molten steel level in tundish based on laser triangulation

Energy Technology Data Exchange (ETDEWEB)

Su, Zhiqi; He, Qing, E-mail: heqing@ise.neu.edu.cn; Xie, Zhi [State Key Laboratory of Synthetical Automation for Process Industries, School of Information Science and Engineering, Northeastern University, Shenyang 110819 (China)

2016-03-15

For real-time and precise measurement of molten steel level in tundish during continuous casting, slag level and slag thickness are needed. Among which, the problem of slag thickness measurement has been solved in our previous work. In this paper, a systematic solution for slag level measurement based on laser triangulation is proposed. Being different from traditional laser triangulation, several aspects for measuring precision and robustness have been done. First, laser line is adopted for multi-position measurement to overcome the deficiency of single point laser range finder caused by the uneven surface of the slag. Second, the key parameters, such as installing angle and minimum requirement of the laser power, are analyzed and determined based on the gray-body radiation theory to fulfill the rigorous requirement of measurement accuracy. Third, two kinds of severe noises in the acquired images, which are, respectively, caused by heat radiation and Electro-Magnetic Interference (EMI), are cleaned via morphological characteristic of the liquid slag and color difference between EMI and the laser signals, respectively. Fourth, as false target created by stationary slag usually disorders the measurement, valid signals of the slag are distinguished from the false ones to calculate the slag level. Then, molten steel level is obtained by the slag level minus the slag thickness. The measuring error of this solution is verified by the applications in steel plants, which is ±2.5 mm during steady casting and ±3.2 mm at the end of casting.

Eletrobras management program in ergonomics: the pursuit of excellence through maturity levels.

Science.gov (United States)

Pires, Paulo Roberto de Oliveira Bassil; Rezende, Fagner Fagundes

2012-01-01

Ergonomics for Eletrobras arose from the need in having an environment more suitable to the characteristics and circumstances of employees, in compliance with Regulation Standard no. 17 - Ergonomics (NR17) of the Ministry of Labor and Employment. Being a mixed economy company with regionalized anthropometric characteristics of its employees, the study of ergonomic adjustments and improvement of the concept of Ergonomics were and have been of great importance to the company's production environment. These advances have contributed to the development of specific technical criteria for the purchase of furniture and work tools (accessories), apart from their possible effects on the user. Ergonomics has been perceived as a technical-scientific tool, aimed to study labor interactions, new technologies and specific characteristics of the activities performed. To meet these demands a multidisciplinary Ergonomics Committee was created in Eletrobras, and effectively established the Ergonomics Management Program in the company; This program is marked by well-defined phases with great success in making use of these studies for other types of corporate activities and also facilitating the program control and its maturity levels, even at a business level.

The optimization design of nuclear measurement teaching equipment

International Nuclear Information System (INIS)

Tang Rulong; Qiu Xiaoping

2008-01-01

So far domestic student-oriented experimental nuclear measuring instruments are used only to measure object density, thickness or material level, and in the choice of sources activity is mostly about 10 mCi. this design will proposed a optimization program dealing with domestic situation. It discussed the radioactive sources activity, the structural design of sealed sources, such as the choice of the tested material in order to get a program optimization. The program used 1 mCi activity radioactive sources 137 Cs to reduce the radiation dose, and the measurement function was improved. So that the apparatus can measure density, thickness nad material level. (authors)

Measurements of radon levels inside Mexican caves

International Nuclear Information System (INIS)

Borau, J.; Gonzalez, A.; Espinosa, G.; Golzarri, J.I.

1993-01-01

Living animal species on earth have been exposed to environmental radon from the very beginning of time. The effects of radiation, combined with other natural parameters such as temperature, humidity, salt contents, etc., have most likely influenced the evaluation of different species. Thus, it is important to know and to evaluate the radon levels, among other radioactive elements present in enclosed environments such as caves, especially since those caves were also the dwellings and refuge of the predecessor of man. In this work we present radon level measurements inside some caves with vestiges of ancient inhabitats and some recently discovered natural caves, using Nuclear Track Detectors. (author)

Knowledge is power: Customer load metering in the Victorian End-Use Measurement Program

Energy Technology Data Exchange (ETDEWEB)

Gavin, G. [CitiPower Ltd., Melbourne, VIC (Australia)

1995-12-31

The Victorian End-Use Measurement Program is a sophisticated load metering program being conducted over 500 sites in Victoria, covering the major customer sectors of residential, commercial and industrial. Its goal is to gather sufficient data to determine with statistical accuracy the load profiles of these major sectors, together with the load profiles of selected customer end-uses in the residential and commercial sectors, and selected building types in the commercial sector. This paper discusses the major elements of the program, the history of its development, the design of the statistical and operational components of the program, and its implementation in the field. In the Victorian electricity industry, with the combination of contestable customer metering and the End-Use Measurement program metering for the franchise/non-contestable market, there is now a considerable flow of customer load data. The opportunity exists for an accurate understanding of customer load needs, and the minimization of risk in business operations in the retail and wholesale market. (author).

Measuring Levels of Work in Academic Libraries: A Time Based Approach.

Science.gov (United States)

Gould, Donald P.

1985-01-01

Using Stratified Systems Theory, which focuses on the manager-subordinate relationship in the bureaucratic structure, a study was conducted to measure level of responsibility in work of 37 professional and nonprofessional positions in four academic library technical services departments. Three levels of work were measured in "time-spans of…

Noninvasive measurement of blood glucose level using mid-infrared quantum cascade lasers

Science.gov (United States)

Yoshioka, Kiriko; Kino, Saiko; Matsuura, Yuji

2017-04-01

For non-invasive measurement of blood glucose level, attenuated total reflection (ATR) absorption spectroscopy system using a QCL as a light source was developed. The results of measurement of glucose solutions showed that the system had a sensitivity that was enough for blood glucose measurement. In-vivo measurement using the proposed system based on QCL showed that there was a correlation between absorptions measured with human lips and blood glucose level.

Description of the U.S. Geological Survey's water-quality sampling and water-level monitoring program at the Hallam Nuclear Facility, August through September 1997

International Nuclear Information System (INIS)

1997-01-01

A water-quality and water-level program between the US Department of Energy (USDOE) and the US Geological Survey (USGS) was re-established in August 1997 to (1) collect one set of water-quality samples from 17 of the 19 USDOE monitor wells, and (2) make five water-level measurements during a 2-month period from the 19 USDOE monitor wells at the Hallam Nuclear Facility, Hallam, Nebraska. Data from these wells are presented

Recent advances in measurements of the nuclear level density

International Nuclear Information System (INIS)

John, Bency

2007-01-01

A short review of recent advances in measurements of the nuclear level density is given. First results of the inverse level density parameter - angular momentum correlation in a number of nuclei around Z∼50 shell region at an excitation energy around 0.3 MeV/nucleon are presented. Significant variations observed over and above the expected shell corrections are discussed in context of the emerging trends in microscopic calculations of the nuclear level density. (author)

SAGE II Measurements of Stratospheric Aerosol Properties at Non-Volcanic Levels

Science.gov (United States)

Thomason, Larry W.; Burton, Sharon P.; Luo, Bei-Ping; Peter, Thomas

2008-01-01

Since 2000, stratospheric aerosol levels have been relatively stable and at the lowest levels observed in the historical record. Given the challenges of making satellite measurements of aerosol properties at these levels, we have performed a study of the sensitivity of the product to the major components of the processing algorithm used in the production of SAGE II aerosol extinction measurements and the retrieval process that produces the operational surface area density (SAD) product. We find that the aerosol extinction measurements, particularly at 1020 nm, remain robust and reliable at the observed aerosol levels. On the other hand, during background periods, the SAD operational product has an uncertainty of at least a factor of 2 during due to the lack of sensitivity to particles with radii less than 100 nm.

Program-level and contextual-level determinants of low-median CD4+ cell count in cohorts of persons initiating ART in eight sub-Saharan African countries.

Science.gov (United States)

Nash, Denis; Wu, Yingfeng; Elul, Batya; Hoos, David; El Sadr, Wafaa

2011-07-31

In sub-Saharan Africa, many patients initiate antiretroviral therapy (ART) at CD4 cell counts much lower than those recommended in national guidelines. We examined program-level and contextual-level factors associated with low median CD4 cell count at ART initiation in populations initiating ART. Multilevel analysis of aggregate and program-level service delivery data. We examined data on 1690 cohorts of patients initiating ART during 2004-2008 in eight sub-Saharan African countries. Cohorts with median CD4 less than 111 cells/μl (the lowest quartile) were classified as having low median CD4 cell count at ART initiation. Cohort information was combined with time-updated program-level data and subnational contextual-level data, and analyzed using multilevel models. The 1690 cohorts had median CD4 cell count of 136 cells/μl and included 121,504 patients initiating ART at 267 clinics. Program-level factors associated with low cohort median CD4 cell count included urban setting [adjusted odds ratio (AOR) 2.1; 95% confidence interval (CI) 1.3-3.3], lower provider-to-patient ratio (AOR 2.2; 95% CI 1.3-4.0), no PMTCT program (AOR 3.6; 95% CI 1.0-12.8), outreach services for ART patients only vs. both pre-ART and ART patients (AOR 2.4; 95% CI 1.5-3.9), fewer vs. more adherence support services (AOR 1.6; 95% CI 1.0-2.5), and smaller cohort size (AOR 2.5; 95% CI 1.4-4.5). Contextual-level factors associated with low cohort median CD4 cell count included initiating ART in areas where a lower proportion of the population heard of AIDS, tested for HIV recently, and a higher proportion believed 'limiting themselves to one HIV-uninfected sexual partner reduces HIV risk'. Determinants of CD4 cell count at ART initiation in populations initiating ART operate at multiple levels. Structural interventions targeting points upstream from ART initiation along the continuum from infection to diagnosis to care engagement are needed.

Single uniform FBG for simultaneous measurement of liquid level and temperature

International Nuclear Information System (INIS)

Shu, Xuewen; Sugden, Kate; Bennion, Ian

2010-01-01

In this paper, we propose and demonstrate a novel scheme for simultaneous measurement of liquid level and temperature based on a simple uniform fiber Bragg grating (FBG) by monitoring both the short-wavelength-loss peaks and its Bragg resonance. The liquid level can be measured from the amplitude changes of the short-wavelength-loss peaks, while temperature can be measured from the wavelength shift of the Bragg resonance. Both theoretical simulation results and experimental results are presented. Such a scheme has some advantages including robustness, simplicity, flexibility in choosing sensitivity and simultaneous temperature measurement capability

Improvements on Low Level Activity Gamma Measurements and X-ray Spectrometry at the CEA-MADERE Measurement Platform

OpenAIRE

Sergeyeva Victoria; Domergue Christophe; Destouches Christophe; Girard Jean Michel; Philibert Hervé; Bonora Jonathan; Thiollay Nicolas; Lyoussi Abdallah

2016-01-01

The CEA MADERE platform (Measurement Applied to DosimEtry in REactors) is a part of the Instrumentation Sensors and Dosimetry Laboratory (LDCI). This facility is dedicated to the specific activity measurements of solid and radioactive samples using Gamma and X-ray spectrometry. MADERE is a high-performance facility devoted to neutron dosimetry for experimental programs performed in CEA and for the irradiation surveillance programmes of PWR vessels. The MADERE platform is engaged in a continuo...

Atmospheric radiation measurement program facilities newsletter, September 2001.; TOPICAL

International Nuclear Information System (INIS)

Holdridge, D. J.

2001-01-01

Our Changing Climate-Is our climate really changing? How do we measure climate change? How can we predict what Earth's climate will be like for generations to come? One focus of the Atmospheric Radiation Measurement (ARM) Program is to improve scientific climate models enough to achieve reliable regional prediction of future climate. According to the Environmental Protection Agency (EPA), the global mean surface temperature has increased by 0.5-1.0 F since the late 19th century. The 20th century's 10 warmest years all occurred in the last 15 years of the century, with 1998 being the warmest year of record. The global mean surface temperature is measured by a network of temperature-sensing instruments distributed around the world, including ships, ocean buoys, and weather stations on land. The data from this network are retrieved and analyzed by various organizations, including the National Aeronautics and Space Administration, the National Oceanic and Atmospheric Administration, and the World Meteorological Organization. Worldwide temperature records date back to 1860. To reconstruct Earth's temperature history before 1860, scientists use limited temperature records, along with proxy indicators such as tree rings, pollen records, and analysis of air frozen in ancient ice. The solar energy received from the sun drives Earth's weather and climate. Some of this energy is reflected and filtered by the atmosphere, but most is absorbed by Earth's surface. The absorbed solar radiation warms the surface and is re-radiated as heat energy into the atmosphere. Some atmospheric gases, called greenhouse gases, trap some of the re-emitted heat, keeping the surface temperature regulated and suitable for sustaining life. Although the greenhouse effect is natural, some evidence indicates that human activities are producing increased levels of some greenhouse gases such as carbon dioxide, methane, and nitrous oxide. Scientists believe that the combustion of fossil fuels is

75 FR 6673 - Expert Meeting on Measurement Criteria for Children's Health Insurance Program; Reauthorization...

Science.gov (United States)

2010-02-10

... on Measurement Criteria for Children's Health Insurance Program; Reauthorization Act Pediatric... enacted in the Children's Health Insurance Program Reauthorization Act (CHIPRA). DATES: The meeting will...) reauthorized the Child Health Insurance Program (CHIP) originally established in 1997, and in Title IV of the...

The Evaluation of Steam Generator Level Measurement Model for OPR1000 Using RETRAN-3D

International Nuclear Information System (INIS)

Doo Yong Lee; Soon Joon Hong; Byung Chul Lee; Heok Soon Lim

2006-01-01

Steam generator level measurement is important factor for plant transient analyses using best estimate thermal hydraulic computer codes since the value of steam generator level is used for steam generator level control system and plant protection system. Because steam generator is in the saturation condition which includes steam and liquid together and is the place that heat exchange occurs from primary side to secondary side, computer codes are hard to calculate steam generator level realistically without appropriate level measurement model. In this paper, we prepare the steam generator models using RETRAN-3D that include geometry models, full range feedwater control system and five types of steam generator level measurement model. Five types of steam generator level measurement model consist of level measurement model using elevation difference in downcomer, 1D level measurement model using fluid mass, 1D level measurement model using fluid volume, 2D level measurement model using power and fluid mass, and 2D level measurement model using power and fluid volume. And we perform the evaluation of the capability of each steam generator level measurement model by simulating the real plant transient condition, the title is 'Reactor Trip by The Failure of The Deaerator Level Control Card of Ulchin Unit 3'. The comparison results between real plant data and RETRAN-3D analyses for each steam generator level measurement model show that 2D level measurement model using power and fluid mass or fluid volume has more realistic prediction capability compared with other level measurement models. (authors)

Measurement of Acceptable Noise Level with Background Music.

Science.gov (United States)

Ahn, Hyun-Jung; Bahng, Junghwa; Lee, Jae Hee

2015-09-01

Acceptable noise level (ANL) is a measure of the maximum background noise level (BNL) that a person is willing to tolerate while following a target story. Although researchers have used various sources of target sound in ANL measures, a limited type of background noise has been used. Extending the previous study of Gordon-Hickey & Moore (2007), the current study determined the effect of music genre and tempo on ANLs as possible factors affecting ANLs. We also investigated the relationships between individual ANLs and the familiarity of music samples and between music ANLs and subjective preference. Forty-one participants were seperated into two groups according to their ANLs, 29 low-ANL listeners and 12 high-ANL listeners. Using Korean ANL material, the individual ANLs were measured based on the listeners' most comfortable listening level and BNL. The ANLs were measured in six conditions, with different music tempo (fast, slow) and genre (K-pop, pop, classical) in a counterbalanced order. Overall, ANLs did not differ by the tempo of background music, but music genre significantly affected individual ANLs. We observed relatively higher ANLs with K-pop music and relatively lower ANLs with classical music. This tendency was similar in both low-ANL and high-ANL groups. However, the subjective ratings of music familiarity and preference affected ANLs differently for low-ANL and high-ANL groups. In contrast to the low-ANL listeners, the ANLs of the high-ANL listeners were significantly affected by music familiarity and preference. The genre of background music affected ANLs obtained using background music. The degree of music familiarity and preference appears to be associated with individual susceptibility to background music only for listeners who are greatly annoyed by background noise (high-ANL listeners).

Medicaid/CHIP Program; Medicaid Program and Children's Health Insurance Program (CHIP); Changes to the Medicaid Eligibility Quality Control and Payment Error Rate Measurement Programs in Response to the Affordable Care Act. Final rule.

Science.gov (United States)

2017-07-05

This final rule updates the Medicaid Eligibility Quality Control (MEQC) and Payment Error Rate Measurement (PERM) programs based on the changes to Medicaid and the Children's Health Insurance Program (CHIP) eligibility under the Patient Protection and Affordable Care Act. This rule also implements various other improvements to the PERM program.

The Savannah River Plant low-level waste segregation program

International Nuclear Information System (INIS)

Wheeler, V.B.

1987-01-01

To extend the life of the Savannah River Plant (SRP) Radioactive Waste Burial Ground, a sitewide program has been implemented to segregate waste that is essentially free of contamination from routine radioactive waste. Much of the low-level waste disposed of as radioactive has no detectable contamination and can be buried in a sanitary landfill. A Landfill Monitoring Facility (LMF) will be constructed at SRP to house the state-of-the-art technology required to provide a final survey on the candidate waste streams that had previously been classified as radioactive. 3 figs

What's Working: Program Factors Influencing California Community College Basic Skills Mathematics Students' Advancement to Transfer Level

Science.gov (United States)

Fiero, Diane M.

2013-01-01

Purpose: The purpose of this study was to determine which basic skills program factors were exhibited by successful basic skills programs that helped students advance to transfer-level mathematics. This study specifically examined California community college basic skills programs that assist students who place in mathematics courses 2 levels…

IMPACT OF DIET, EXERCISE AND DIET COMBINED WITH EXERCISE PROGRAMS ON PLASMA LIPOPROTEIN AND ADIPONECTIN LEVELS IN OBESE GIRLS

Directory of Open Access Journals (Sweden)

Omar Ben Ounis

2008-12-01

Full Text Available We studied the effect of three programs, diet restriction (D, individualized exercise training (E at the maximal lipid oxidation point (LIPOXmax and diet combined with exercise (D+E, on body mass, plasma lipoprotein and adiponectin levels in obese girls. Eighteen obese adolescents girls aged 12-14 years were studied. A longitudinal intervention was carried out, consisting of a two-month diet (D; -500 kcal·day-1, of individualized exercise (E; 4 days/week, 90 min·day-1 and of diet combined with exercise (D+E. Body mass, body mass index (BMI, body fat mass, waist circumference, substrate crossover point, LIPOXmax point, homeostasis model assessment (HOMA-IR index, fasting levels of lipids and circulatory adiponectin, were measured in all subjects before and after the program. In subjects of the D+E group, body mass, BMI, body fat mass, waist circumference, HOMA-IR, low-density lipoprotein cholesterol (LDL-C and total cholesterol / high-density lipoprotein cholesterol (TC/HDL-C ratio were significantly lower, and HDL-C and adiponectin were higher after the program than that of subjects in the D or E groups. Diet/exercise improved the ability to oxidize lipids during exercise (crossover point: + 18.5 ± 3.4 of % Wmax; p < 0.01 and fat oxidation rate at LIPOXmax: + 89.7 ± 19.7 mg·min-1; p < 0.01. In the D+E group, significant correlations were found between changes in body mass and adiponectin and between changes in the TC/HDL-C ratio and LIPOXmax. These findings show that the combined program of diet restriction and individualized exercise training at the LIPOXmax point is necessary to simultaneously improve body mass loss, adiponectin levels, as well as metabolic parameters, in obese girls

Low-level violence in schools: is there an association between school safety measures and peer victimization?

Science.gov (United States)

Blosnich, John; Bossarte, Robert

2011-02-01

Low-level violent behavior, particularly school bullying, remains a critical public health issue that has been associated with negative mental and physical health outcomes. School-based prevention programs, while a valuable line of defense to stave off bullying, have shown inconsistent results in terms of decreasing bullying. This study explored whether school safety measures (eg, security guards, cameras, ID badges) were associated with student reports of different forms of peer victimization related to bullying. Data came from the 2007 School Crime Supplement of the National Crime Victimization Survey. Chi-square tests of independence were used to examine differences among categorical variables. Logistic regression models were constructed for the peer victimization outcomes. A count variable was constructed among the bullying outcomes (0-7) with which a Poisson regression model was constructed to analyze school safety measures' impacts on degree of victimization. Of the various school safety measures, only having adults in hallways resulted in a significant reduction in odds of being physically bullied, having property vandalized, or having rumors spread. In terms of degree of victimization, having adults and/or staff supervising hallways was associated with an approximate 26% decrease in students experiencing an additional form of peer victimization. Results indicated that school safety measures overall were not associated with decreased reports of low-level violent behaviors related to bullying. More research is needed to further explore what best promotes comprehensive safety in schools. © 2011, American School Health Association.

Historic low-level radioactive waste federal policies, programs and oversight

International Nuclear Information System (INIS)

Blanchette, M.; Kenney, J.; Zelmer, B.

2011-01-01

'Full text:' The management of radioactive waste is one of the most serious environmental problems facing Canadians. From the early industrial uses of radioactive material in the 1930s to the development of nuclear power reactors and the medical and experimental use of radio-isotopes today, there has been a steady accumulation of waste products. Historic waste is low-level radioactive waste for which the federal government has accepted responsibility for long-term management. This paper will outline the policy framework used to govern institutional and financial arrangements for the disposal of radioactive waste by waste producers and owners and the major radioactive projects in which the Government of Canada is currently involved. It will provide an overview of the organizations established for the management of historic radioactive waste and NRCan's oversight role. Finally, an overview of the historic waste program activities managed on behalf of the federal government through these organizations in the Port Hope area, the Greater Toronto Area, in Fort McMurray, Alberta and along the Northern Transportation Route is provided. Canada's Policy Framework for Radioactive Waste, sets out principles that govern the institutional and financial arrangements for disposal of radioactive waste by waste producers and owners. According to the Policy Framework: The federal government will ensure that radioactive waste disposal is carried out in a safe, environmentally sound, comprehensive, cost-effective and integrated manner; The federal government has the responsibility to develop policy, to regulate, and to oversee producers and owners; and, The waste producers and owners are responsible, in accordance with the principle of 'polluter pays', for the funding, organization, management and operation of disposal and other facilities required for their wastes. Arrangements may be different for nuclear fuel waste, low-level radioactive waste and

A program-level management system for the life cycle environmental and economic assessment of complex building projects

International Nuclear Information System (INIS)

Kim, Chan-Joong; Kim, Jimin; Hong, Taehoon; Koo, Choongwan; Jeong, Kwangbok; Park, Hyo Seon

2015-01-01

Climate change has become one of the most significant environmental issues, of which about 40% come from the building sector. In particular, complex building projects with various functions have increased, which should be managed from a program-level perspective. Therefore, this study aimed to develop a program-level management system for the life-cycle environmental and economic assessment of complex building projects. The developed system consists of three parts: (i) input part: database server and input data; (ii) analysis part: life cycle assessment and life cycle cost; and (iii) result part: microscopic analysis and macroscopic analysis. To analyze the applicability of the developed system, this study selected ‘U’ University, a complex building project consisting of research facility and residential facility. Through value engineering with experts, a total of 137 design alternatives were established. Based on these alternatives, the macroscopic analysis results were as follows: (i) at the program-level, the life-cycle environmental and economic cost in ‘U’ University were reduced by 6.22% and 2.11%, respectively; (ii) at the project-level, the life-cycle environmental and economic cost in research facility were reduced 6.01% and 1.87%, respectively; and those in residential facility, 12.01% and 3.83%, respective; and (iii) for the mechanical work at the work-type-level, the initial cost was increased 2.9%; but the operation and maintenance phase was reduced by 20.0%. As a result, the developed system can allow the facility managers to establish the operation and maintenance strategies for the environmental and economic aspects from a program-level perspective. - Highlights: • A program-level management system for complex building projects was developed. • Life-cycle environmental and economic assessment can be conducted using the system. • The design alternatives can be analyzed from the microscopic perspective. • The system can be used to

A program-level management system for the life cycle environmental and economic assessment of complex building projects

Energy Technology Data Exchange (ETDEWEB)

Kim, Chan-Joong [Parsons Brinckerhoff, Seoul 135-763 (Korea, Republic of); Kim, Jimin; Hong, Taehoon; Koo, Choongwan; Jeong, Kwangbok; Park, Hyo Seon [Department of Architectural Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)

2015-09-15

Climate change has become one of the most significant environmental issues, of which about 40% come from the building sector. In particular, complex building projects with various functions have increased, which should be managed from a program-level perspective. Therefore, this study aimed to develop a program-level management system for the life-cycle environmental and economic assessment of complex building projects. The developed system consists of three parts: (i) input part: database server and input data; (ii) analysis part: life cycle assessment and life cycle cost; and (iii) result part: microscopic analysis and macroscopic analysis. To analyze the applicability of the developed system, this study selected ‘U’ University, a complex building project consisting of research facility and residential facility. Through value engineering with experts, a total of 137 design alternatives were established. Based on these alternatives, the macroscopic analysis results were as follows: (i) at the program-level, the life-cycle environmental and economic cost in ‘U’ University were reduced by 6.22% and 2.11%, respectively; (ii) at the project-level, the life-cycle environmental and economic cost in research facility were reduced 6.01% and 1.87%, respectively; and those in residential facility, 12.01% and 3.83%, respective; and (iii) for the mechanical work at the work-type-level, the initial cost was increased 2.9%; but the operation and maintenance phase was reduced by 20.0%. As a result, the developed system can allow the facility managers to establish the operation and maintenance strategies for the environmental and economic aspects from a program-level perspective. - Highlights: • A program-level management system for complex building projects was developed. • Life-cycle environmental and economic assessment can be conducted using the system. • The design alternatives can be analyzed from the microscopic perspective. • The system can be used to

Ionization chamber for measurements of high-level tritium gas

International Nuclear Information System (INIS)

Carstens, D.H.W.; David, W.R.

1980-01-01

The construction and calibration of a simple ionization-chamber apparatus for measurement of high level tritium gas is described. The apparatus uses an easily constructed but rugged chamber containing the unknown gas and an inexpensive digital multimeter for measuring the ion current. The equipment after calibration is suitable for measuring 0.01 to 100% tritium gas in hydrogen-helium mixes with an accuracy of a few percent. At both the high and low limits of measurements deviations from the predicted theoretical current are observed. These are briefly discussed

Introducing B2B Service Level Measures via a Poker-Card Activity

Science.gov (United States)

Chen, Chun-Miin; Bailey, Matthew D.

2016-01-01

To determine the appropriate level of product availability, most operations management textbooks introduce and define service level measures in a Business-to-Customer context. In other words, a retailer that wants to measure product availability in their store calculates the fill rate (FR) or cycle service level over an infinite review horizon.…

Changes in selected physical, motor performance and anthropometric components of university-level rugby players after one microcycle of a combined rugby conditioning and plyometric training program.

Science.gov (United States)

Pienaar, Cindy; Coetzee, Ben

2013-02-01

The purpose of this study was to determine the effects of a microcycle (4 weeks) combined rugby conditioning plyometric compared with a nonplyometric rugby conditioning program on selected physical and motor performance components and anthropometric measurements of university-level rugby players. Players (18.94 ± 0.40 years) were assigned to either a control (n = 16) or experimental group (n = 19) from the U/19 rugby teams of the North-West University (South Africa). Twenty-six direct and indirect anthropometric measurements were taken, and the players performed a battery of 5 physical and motor performance tests before and after a microcycle (4 week) combined rugby conditioning plyometric (experimental group) and a nonplyometric rugby conditioning program (control group). The dependent t-test results showed that the control group's upper-body explosive power decreased significantly, whereas the stature, skeletal mass, and femur breadth increased significantly from pre- to posttesting. The experimental group showed significant increases in wrist breadth, speed over 20 m, agility, and power and work measurements of the Wingate anaerobic test (WAnT). Despite these results, the independent t-test revealed that speed over 20 m, average power output at 20 seconds, relative work of the WAnT, and agility were the only components of the experimental group that improved significantly more than the control group. A microcycle combined rugby conditioning plyometric program therefore leads to significantly bigger changes in selected physical and motor performance components of university-level rugby players than a nonplyometric rugby conditioning program alone. Based on these findings, coaches and sport scientists should implement 3 weekly combined rugby conditioning plyometric programs in rugby players' training regimens to improve the players' speed, agility, and power.

An application of data mining classification and bi-level programming for optimal credit allocation

Directory of Open Access Journals (Sweden)

Seyed Mahdi Sadatrasou

2015-01-01

Full Text Available This paper investigates credit allocation policy making and its effect on economic development using bi-level programming. There are two challenging problems in bi-level credit allocation; at the first level government/public related institutes must allocate the credit strategically concerning sustainable development to regions and industrial sectors. At the second level, there are agent banks, which should allocate the credit tactically to individual applicants based on their own profitability and risk using their credit scoring models. There is a conflict of interest between these two stakeholders but the cooperation is inevitable. In this paper, a new bi-level programming formulation of the leader-follower game in association with sustainable development theory in the first level and data mining classifier at the second level is used to mathematically model the problem. The model is applied to a national development fund (NDF as a government related organization and one of its agent banks. A new algorithm called Bi-level Genetic fuzzy apriori Algorithm (BGFAA is introduced to solve the bilateral model. Experimental results are presented and compared with a unilateral policy making scenario by the leader. Findings show that although the objective functions of the leader are worse in the bilateral scenario but agent banks collaboration is attracted and guaranteed.

Review of Evaluation, Measurement and Verification Approaches Used to Estimate the Load Impacts and Effectiveness of Energy Efficiency Programs

Energy Technology Data Exchange (ETDEWEB)

Messenger, Mike; Bharvirkar, Ranjit; Golemboski, Bill; Goldman, Charles A.; Schiller, Steven R.

2010-04-14

Efficiency (2007) presented commonly used definitions for EM&V in the context of energy efficiency programs: (1) Evaluation (E) - The performance of studies and activities aimed at determining the effects and effectiveness of EE programs; (2) Measurement and Verification (M&V) - Data collection, monitoring, and analysis associated with the calculation of gross energy and demand savings from individual measures, sites or projects. M&V can be a subset of program evaluation; and (3) Evaluation, Measurement, and Verification (EM&V) - This term is frequently seen in evaluation literature. EM&V is a catchall acronym for determining both the effectiveness of program designs and estimates of load impacts at the portfolio, program and project level. This report is a scoping study that assesses current practices and methods in the evaluation, measurement and verification (EM&V) of ratepayer-funded energy efficiency programs, with a focus on methods and practices currently used for determining whether projected (ex-ante) energy and demand savings have been achieved (ex-post). M&V practices for privately-funded energy efficiency projects (e.g., ESCO projects) or programs where the primary focus is greenhouse gas reductions were not part of the scope of this study. We identify and discuss key purposes and uses of current evaluations of end-use energy efficiency programs, methods used to evaluate these programs, processes used to determine those methods; and key issues that need to be addressed now and in the future, based on discussions with regulatory agencies, policymakers, program administrators, and evaluation practitioners in 14 states and national experts in the evaluation field. We also explore how EM&V may evolve in a future in which efficiency funding increases significantly, innovative mechanisms for rewarding program performance are adopted, the role of efficiency in greenhouse gas mitigation is more closely linked, and programs are increasingly funded from multiple sources

Collective dose as a performance measure for occupational radiation protection programs: Issues and recommendations

International Nuclear Information System (INIS)

Strom, D.J.; Harty, R.; Hickey, E.E.; Martin, J.B.; Peffers, M.S.; Kathren, R.L.

1998-07-01

Collective dose is one of the performance measures used at many US Department of Energy (DOE) contractor facilities to quantitatively assess the objectives of the radiation protection program. It can also be used as a management tool to improve the program for keeping worker doses as low as reasonably achievable (ALARA). Collective dose is used here to mean the sum of all total effective dose equivalent values for all workers in a specified group over a specified time. It is often used as a surrogate estimate of radiological risk. In principle, improvements in radiation protection programs and procedures will result in reduction of collective dose, all other things being equal. Within the DOE, most frequently, a single collective dose number, which may or may not be adjusted for workload and other factors, is used as a performance measure for a contractor. The purpose of this report is to evaluate the use of collective dose as a performance measure for ALARA programs at DOE sites

A bi-level programming for multistage co-expansion planning of the integrated gas and electricity system

DEFF Research Database (Denmark)

Zeng, Qing; Zhang, Baohua; Fang, Jiakun

2017-01-01

as the generation capacities, while the lower-level is formulated as an optimal economic dispatch under the operational constraints given by the upper-level decision. To solve the bi-level multi-stage programming problem, a hybrid algorithm is proposed combining the modified binary particle swarm optimization (BPSO...... power systems. The system operation is optimized and embedded in the planning horizon. A bi-level multi-stage programming problem is formulated to minimize the investment cost plus the operational cost. The upper-level optimizes the expansion plan and determines the network topology as well......) and the interior point method (IPM). The BPSO is used for the upper-level sub-problem, and the IPM is adopted for the lower-level sub-problem. Numerical case studies have been carried out on the practical gas and electricity transmission network in western Denmark. Simulation results demonstrate the effectiveness...

A Pilot Study on Measuring Customer’s Satisfaction Level

Directory of Open Access Journals (Sweden)

Vide Boltez

2013-01-01

Full Text Available RQ: Determine the level of customer satisfaction of a company’s products and services to obtain information on needed improvements.Purpose: The purpose of measuring customer’s satisfaction level is to obtain information directly from the final buyer that bought our product. The next step is to analyze the information obtained and to take the results into consideration to improve the working process in production and in other departments of the company.Method: The method used for the pilot study to measure customer satisfaction was a short questionnaire that was given to 10 customers of our product and 10 completed questionnaires were obtained.Results: The results showed the level of satisfaction of final buyers of roof tiles and roofs that the company has achieved through their products and services. The results facilitate the production, logistics, purchasing and sales department to obtain information on positive satisfaction levels and areas that need change. At the same time, the final buyer was identified (i.e., name, surname, address, and so forth, which up until now had not been.Organization: The organization will save time and money in the future, because it will continuously measure customer satisfaction to improve production and other departments in the organization towards creating satisfied customers.Society: Final buyers of roofs are, and will be, more satisfied with their decisions, because the organization carries out after-sales satisfaction levels.Originality: The research was original, because up to this date the organization has not conducted research in such a manner.Limitations: The pilot study used 10 completed questionnaires that represent a very small sample to make any generalizations.

DOE`s integrated low-level waste management program and strategic planning

Energy Technology Data Exchange (ETDEWEB)

Duggan, G. [Dept. of Energy, Washington, DC (United States). Office of Environmental Restoration and Waste Management; Hwang, J. [Science Applications International Corp., Germantown, MD (United States)

1993-03-01

To meet the DOE`s commitment to operate its facilities in a safe, economic, and environmentally sound manner, and to comply with all applicable federal, state, and local rules, regulations, and agreements, DOE created the Office of Environmental Restoration and Waste Management (EM) in 1989 to focus efforts on controlling waste management and cleaning up contaminated sites. In the first few years of its existence, the Office of Waste Management (EM-30) has concentrated on operational and corrective activities at the sites. In 1992, the Office of Waste Management began to apply an integrated approach to managing its various waste types. Consequently, DOE established the Low-Level Waste Management Program (LLWMP) to properly manage its complex-wide LLW in a consistent manner. The objective of the LLWMP is to build and operate an integrated, safe, and cost-effective program to meet the needs of waste generators. The program will be based on acceptable risk and sound planning, resulting in public confidence and support. Strategic planning of the program is under way and is expected to take two to three years before implementation of the integrated waste management approach.

Measurement and evaluation of energy efficiency programs: California and South Korea

International Nuclear Information System (INIS)

Vine, E.; Rhee, C.H.; Lee, K.D.

2006-01-01

One of the key challenges for countries facing electric utility restructuring is to ensure that key public goods, such as energy efficiency programs, do not lose support but are maintained and enhanced via regulatory policy and government action. Moreover, an infrastructure and process also needs to be designed and implemented for conducting the measurement and evaluation of energy efficiency programs. This paper describes the experiences of California and the Republic of Korea (Korea) in addressing these issues. These case studies confirm that the active involvement of regulatory bodies is needed to ensure that energy efficiency investments continue. The case studies also show that the development of an infrastructure and process for conducting rigorous measurement and evaluation takes time and needs the active participation of many stakeholders

Design of FitFor2 study: the effects of an exercise program on insulin sensitivity and plasma glucose levels in pregnant women at high risk for gestational diabetes

Directory of Open Access Journals (Sweden)

Eekhoff Elisabeth MW

2009-01-01

Full Text Available Abstract Background Pregnancy is a period in the life of women that is often associated with decreased daily physical activity and/or exercise. However, maintaining adequate levels of daily physical activity during pregnancy is important for mother and child. Studies suggest that moderate daily physical activity and exercise during pregnancy are associated with reductions in the risk of gestational diabetes mellitus (GDM. However, at present, physical activity is not routinely advised to pregnant women at risk for gestational diabetes in the Netherlands. In FitFor2-study we aim to assess whether an exercise program can improve insulin sensitivity and fasting plasma glucose levels of women at high risk for gestational diabetes, assuming that this will lower their risk of gestational diabetes. Methods The FitFor2-study is a randomised controlled trial. Women who visit one of the participating hospitals or midwifery practices and who are at risk for gestational diabetes are eligible to participate. After baseline measurement they are randomly allocated to in the intervention or control group. The intervention group receives an exercise program twice a week in addition to usual care. The exercise program consist of aerobic and strength exercises and takes place under close supervision of a physiotherapist. Data are collected at 15, 24 and 32 weeks of pregnancy and 12 weeks after delivery. Primary maternal outcome measures are fasting plasma glucose and relative increase in insulin resistance. Primary neonatal outcome is birth weight. Secondary outcome measures are: maternal serum triglycerides, HDL, cholesterol, HbA1c, maternal weight gain during pregnancy, maternal physical activity level, foetal growth. Discussion If the FitFor2 intervention program proves to be effective, obstetricians and midwives should refer women at risk for GDM to a special exercise program. Exercise programs for pregnant women under supervision of an experienced trainer are

Three-level approach to quality programs for research, development and production

International Nuclear Information System (INIS)

Davis, A.H.; Bussolini, P.L.; Geoffrion, R.R.

1986-01-01

A primary mission of the Los Alamos National Laboratory is to develop nuclear weapons systems for the Department of Defense. The activities included in this effort cover a broad spectrum, ranging from pure research to routine production. In order to provide a workable framework for a comprehensive quality assurance program for these varied activities, we have proposed a three-level structure of quality plans, corresponding to a rough classification of the weapons work into three general categories. These categories are: (1) research into materials and processes, and preliminary development; (2) design, development, and fabrication of prototype components; (3) routine production, analysis, or refinement activities. The first category requires a quality program to assure the validity, reliability, and retrievability of the information developed; this is accomplished by a conscientious application of what is generally recognized as good laboratory practice. The second category requires in addition a strong emphasis on design review and inspection. For the third category, a comprehensive quality program is appropriate

High-level waste program management: A ratepayers' and regulatory perspective

International Nuclear Information System (INIS)

Anderson, E.G.

1986-01-01

The nation's electric utility regulators have joined the effort to enhance the federal project to dispose of high-level nuclear waste. Because all financial support comes from ratepayers, the National Association of Regulatory Utility Commissioners (NARUC), through the mechanism of a subcommittee, seeks to investigate and monitor the federal program to provide to the Congress and the U.S. Department of Energy (DOE) the NARUC's unique expertise. Its views to enhance program management and improve cost control are its central contribution. While conveying no lack of confidence in the federal management, the NARUC is imparting its relevant experience derived from review of nuclear power plant construction and cost control. Recommendations are made for more cost-effective program direction and views on its management are given. Financial control, public input and cost responsibilities for disposal of defense and commercial wastes are separately identified. Needs for the DOE's heightened insight into and development of the monitored retrievable storage proposal to the Congress are described. Finally, with a warning that there exists a limit to ratepayer funding of this effort, the request is made for Congressional cost-control hearings and for expanded dialogue between the Department of Engery and financially responsible parties

The Introduction of Data Processing in Middle-Level Accountancy Training Programs in Developing Countries: A Case Study.

Science.gov (United States)

Schramm, Karin

1985-01-01

Examines the impact of introducing data processing in middle-level accountancy training programs in Botswana. Hardware and software considerations for the program are also examined. Since the beginning of the program, some 300 students have been trained in accounting. (JN)

Achievements and experience in Laboratory for Low Level Measurements, Rudjer Boskovic Institute, Croatia, during the IAEA QA/QC program

International Nuclear Information System (INIS)

Obelic, B.; Horvatincic, N.; Krajcar Bronic, I.

2002-01-01

In this summary we explain our motivation for joining the IAEA Program on Quality Assurance and Quality Control in Nuclear Analytical Techniques, the situation in the Laboratory before joining the program, and achievements during this 2-year program. We also describe our experience and difficulties with implementation of the quality system in the Laboratory, as well as with the quality system at the Rudjer Boskovic Institute. Finally, we present our plans for the future

Symmetry and Asymmetry Level Measures

Directory of Open Access Journals (Sweden)

Angel Garrido

2010-04-01

Full Text Available Usually, Symmetry and Asymmetry are considered as two opposite sides of a coin: an object is either totally symmetric, or totally asymmetric, relative to pattern objects. Intermediate situations of partial symmetry or partial asymmetry are not considered. But this dichotomy on the classification lacks of a necessary and realistic gradation. For this reason, it is convenient to introduce "shade regions", modulating the degree of Symmetry (a fuzzy concept. Here, we will analyze the Asymmetry problem by successive attempts of description and by the introduction of the Asymmetry Level Function, as a new Normal Fuzzy Measure. Our results (both Theorems and Corollaries suppose to be some new and original contributions to such very active and interesting field of research. Previously, we proceed to the analysis of the state of art.

The Atmospheric Radiation Measurement Program and interfaces with external data sources

International Nuclear Information System (INIS)

Stokes, G.M.; Cress, T.S.; Melton, R.B.

1993-10-01

The Atmospheric Radiation Measurement (ARM) Program is the Department of Energy's major field project in support of its global change research program. Its objective is to improve the performance of cloud and radiation models and parameterizations in general circulation models (GCMs) used for climate research. The data produced by ARM will be handled and maintained to satisfy the research needs of the program and to be accessible and usable by the general research and academic communities. In addition to data from field instrumentation, ARM Science Team needs include a substantial amount of data from outside the ARM Program (''external data''), which will be acquired and provided routinely through the ARM data system. With respect to data archival and sharing, the ARM Program reflects the objectives delineated by the US Global Change. The purpose of this presentation is to summarize the conceptual designs embodied in the ARM data system and the status of its implementation

Recent Advances in Low-Level Nuclear Measurements at the CEA

International Nuclear Information System (INIS)

Mahe, C.; Lamadie, F.; Le Goaller, C.

2009-01-01

For several years the CEA has been performing nuclear measurements at different stages of decommissioning projects. The characterization tools initially developed for high-level radioactive waste analysis must be adapted to a new area of application: low-level measurements. Recent technical improvements in gamma imaging, gamma spectrometry detectors, and data analysis make it possible to provide relevant radiological data for waste management, as well as to develop robust and optimized decommissioning scenarios from the initial dose rate mapping to the final declared activity. These techniques have been implemented at various nuclear sites for both trial measurement campaigns and expert investigations to localize residual contamination, to identify the radioelements and to provide an accurate estimate of the declarable activity. Different types of measurements and devices have been used: gamma cameras, coded aperture techniques, alpha imaging prototypes, gamma spectrometry detectors (CdZnTe, HPGe, NaI, and LaBr 3 ), dose rate cartography, and calculation codes (Mercure, MCNP, etc.), all of which provide complementary data for radioactive waste categorization. This paper describes the latest developments and methods deployed on decommissioning projects focusing on low-level in situ applications. Waste drum characterization and in situ glove box measurements are discussed and the technologies and performance of gamma imaging systems, gamma spectrometry detectors, calculation codes and software are described. The paper concludes with a review of future developments and tests necessary for these applications. (authors)

Method of calibrating a fluid-level measurement system

Science.gov (United States)

Woodard, Stanley E. (Inventor); Taylor, Bryant D. (Inventor)

2010-01-01

A method of calibrating a fluid-level measurement system is provided. A first response of the system is recorded when the system's sensor(s) is (are) not in contact with a fluid of interest. A second response of the system is recorded when the system's sensor(s) is (are) fully immersed in the fluid of interest. Using the first and second responses, a plurality of expected responses of the system's sensor(s) is (are) generated for a corresponding plurality of levels of immersion of the sensor(s) in the fluid of interest.

RLV-TD Flight Measured Aeroacoustic Levels and its Comparison with Predictions

Science.gov (United States)

Manokaran, K.; Prasath, M.; Venkata Subrahmanyam, B.; Ganesan, V. R.; Ravindran, Archana; Babu, C.

2017-12-01

The Reusable Launch Vehicle-Technology Demonstrator (RLV-TD) is a wing body configuration successfully flight tested. One of the important flight measurements is the acoustic levels. There were five external microphones, mounted on the fuselage-forebody, wing, vertical tail, inter-stage (ITS) and core base shroud to measure the acoustic levels from lift-off to splash down. In the ascent phase, core base shroud recorded the overall maximum at both lift-off and transonic conditions. In-flight noise levels measured on the wing is second highest, followed by fuselage and vertical tail. Predictions for flight trajectory compare well at all locations except for vertical tail (4.5 dB). In the descent phase, maximum measured OASPL occurs at transonic condition for the wing, followed by vertical tail and fuselage. Predictions for flight trajectory compare well at all locations except for wing (- 6.0 dB). Spectrum comparison is good in the ascent phase compared to descent phase. Roll Reaction control system (RCS) thruster firing signature is seen in the acoustic measurements on the wing and vertical tail during lift-off.

Cross-Cultural Competency Adaptability of Dental Hygiene Educators in Entry Level Dental Hygiene Programs

Science.gov (United States)

Engeswick, Lynnette Marie

2011-01-01

This study was conducted to discover the extent dental hygiene educators in 25 entry-level dental hygiene programs from the Upper Midwest demonstrate Emotional Resilience, Flexibility and Openness, Perceptual Acuity, and Personal Autonomy as they relate to their level of education and multicultural experiences. An additional purpose was to examine…

Indoor radon level measurements in Iran using AEOI passive dosimeters

International Nuclear Information System (INIS)

Sohrabi, M.; Solaymanian, A.R.

1988-01-01

A passive radon diffusion dosimeter was developed at the RPD of AEOI for nationwide indoor radon level measurements. Several parameters of the dosimeter were studied. Radon levels were determined in about 250 houses in Ramsar (a high natural radiation area), Tehran, Babolsar and Gonabad. In this paper, the results of some dosimeter parameters as well as radon levels in indoor air are reported

Measuring and Assessment the Noise Level in Different Regions in Baghdad City And Compare it with The Allowable Levels

Directory of Open Access Journals (Sweden)

Ibtihaj Abdulwahhab Abdulrazzak

2017-05-01

Full Text Available This study includes measurement of the noise level of four regions in the city of Baghdad (industrial region, commercial region, residential region and quiet region and compare the value of noise in each region with the World Health Organization (WHO allowable limits, and the effect of noise on human health was explained. The "sound level meter (SLM" instrument measuring the noise value in the four regions, three measurement per month through one year was recorded (one measurement every ten days from 1/1/2015 to 30/12/2015. The noise level of the industrial region (75dB compared with the World Health Organization level allowable limit (65dB, while the commercial region (76.28dB versus (55dB and the residential region (74.94dB versus (50dB and the quiet region was (62.36dB versus (40dB of the (WHO allowable limit.

Measuring Nontechnical Aspects of Surgical Clinician Development in an Otolaryngology Residency Training Program.

Science.gov (United States)

Shin, Jennifer J; Cunningham, Michael J; Emerick, Kevin G; Gray, Stacey T

2016-05-01

Surgical competency requires sound clinical judgment, a systematic diagnostic approach, and integration of a wide variety of nontechnical skills. This more complex aspect of clinician development has traditionally been difficult to measure through standard assessment methods. This study was conducted to use the Clinical Practice Instrument (CPI) to measure nontechnical diagnostic and management skills during otolaryngology residency training; to determine whether there is demonstrable change in these skills between residents who are in postgraduate years (PGYs) 2, 4, and 5; and to evaluate whether results vary according to subspecialty topic or method of administration. Prospective study using the CPI, an instrument with previously established internal consistency, reproducibility, interrater reliability, discriminant validity, and responsiveness to change, in an otolaryngology residency training program. The CPI was used to evaluate progression in residents' ability to evaluate, diagnose, and manage case-based clinical scenarios. A total of 248 evaluations were performed in 45 otolaryngology resident trainees at regular intervals. Analysis of variance with nesting and postestimation pairwise comparisons were used to evaluate total and domain scores according to training level, subspecialty topic, and method of administration. Longitudinal residency educational initiative. Assessment with the CPI during PGYs 2, 4, and 5 of residency. Among the 45 otolaryngology residents (248 CPI administrations), there were a mean (SD) of 5 (3) administrations (range, 1-4) during their training. Total scores were significantly different among PGY levels of training, with lower scores seen in the PGY-2 level (44 [16]) compared with the PGY-4 (64 [13]) or PGY-5 level (69 [13]) (P otolaryngology (mean [SD], 72 [14]) than in subspecialties (range, 55 [12], P = .003, to 56 [19], P < .001). Neither administering the examination with an electronic scoring system, rather than a

Workshop on measurement quality assurance for ionizing radiation: Proceedings

Energy Technology Data Exchange (ETDEWEB)

Heath, J.A.; Swinth, K.L. [comps.

1993-12-31

This workshop was held to review the status of secondary level calibration accreditation programs, review related measurement accreditation programs, document lessons learned, and to present changes in programs due to new national priorities involving radioactivity measurements. Contents include: fundamentals of measurement quality assurance (MQA), standards for MQA programs; perspectives and policies; complete MQA programs; future MQA programs; QA/QC programs--radioactivity; QA/QC programs--dosimetry; laboratory procedures for QA/QC; in-house control of reference dosimetry laboratories; in-house controls of radioactivity laboratories; and poster session. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Workshop on measurement quality assurance for ionizing radiation: Proceedings

International Nuclear Information System (INIS)

Heath, J.A.; Swinth, K.L.

1993-01-01

This workshop was held to review the status of secondary level calibration accreditation programs, review related measurement accreditation programs, document lessons learned, and to present changes in programs due to new national priorities involving radioactivity measurements. Contents include: fundamentals of measurement quality assurance (MQA), standards for MQA programs; perspectives and policies; complete MQA programs; future MQA programs; QA/QC programs--radioactivity; QA/QC programs--dosimetry; laboratory procedures for QA/QC; in-house control of reference dosimetry laboratories; in-house controls of radioactivity laboratories; and poster session. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

The Efficacy of Stuttering Measurement Training: Evaluating Two Training Programs

Science.gov (United States)

Bainbridge, Lauren A.; Stavros, Candace; Ebrahimian, Mineh; Wang, Yuedong; Ingham, Roger J.

2015-01-01

Purpose: Two stuttering measurement training programs currently used for training clinicians were evaluated for their efficacy in improving the accuracy of total stuttering event counting. Method: Four groups, each with 12 randomly allocated participants, completed a pretest-posttest design training study. They were evaluated by their counts of…

Penempatan Optimal Phasor Measurement Unit (PMU) Dengan Integer Programming

OpenAIRE

Amrulloh, Yunan Helmy

2013-01-01

Phasor Measurement Unit (PMU) merupakan peralatan yang mampu memberikan pengukuran fasor tegangan dan arus secara real-time. PMU dapat digunakan untuk monitoring, proteksi dan kontrol pada sistem tenaga listrik. Tugas akhir ini membahas penempatan PMU secara optimal berdasarkan topologi jaringan sehingga sistem tenaga listrik dapat diobservasi. Penempatan optimal PMU dirumuskan sebagai masalah Binary Integer Programming (BIP) yang akan memberikan variabel dengan pilihan nilai (0,1) yang menu...

Management Development Programs: The Effects of Management Level and Corporate Strategy. [and] Invited Reaction: Level and Strategy Should and Do Make a Difference!

Science.gov (United States)

Blakely, Gerald L.; And Others

1994-01-01

Consensus of survey responses from 155 of 600 human resource managers was as follows: management development programs emphasized technical skills at lower levels, entrepreneurial skills at senior levels; organizations with corporate growth strategies focused on more areas than those with stability or retrenchment strategies. (Muschewske's reaction…

Seasonality in Children's Pedometer-Measured Physical Activity Levels

Science.gov (United States)

Beighle, Aaron; Alderman, Brandon; Morgan, Charles F.; Le Masurier, Guy

2008-01-01

Seasonality appears to have an impact on children's physical activity levels, but equivocal findings demand more study in this area. With the increased use of pedometers in both research and practice, collecting descriptive data in various seasons to examine the impact of seasonality on pedometer-measured physical activity among children is…

Proceedings of the seventh annual participants' information meeting. DOE Low-Level Waste Management Program

International Nuclear Information System (INIS)

1986-02-01

The Seventh Annual Department of Energy (DOE) Low-Level Waste Management Program (LLWMP) Participants' Information Meeting was held September 10-13, 1985 in Las Vegas, Nevada. The purpose of the meeting was to provide a forum for exchange of information on low-level radioactive waste management activities, requirements, and plans. Attendees included representatives from the DOE Nuclear Energy and Defense Low-Level Waste Management Programs, interim operations offices and their contractor operators; representatives from the US Nuclear Regulatory Commission, US Environmental Protection Agency, US Geological Survey, and their contractors; representatives of states and regions responsible for development of new commercial low-level waste disposal facilities; representatives of Great Britain, France, and Canada; representatives of utilities, private contractors, and parties concerned with low-level waste management issues. The meeting was organized by topical areas to allow for the exchange of information and the promotion of discussion on specific aspects of low-level waste management. Plenary sessions were held at the start and conclusion of the meeting while seven concurrent topical sessions were held during the intervening day and a half. Session chairmen from each of these concurrent sessions presented a summary of the discussion and conclusions resulting from their respective sessions at the final plenary session

A Study of Visible Tattoos in Entry-Level Dental Hygiene Education Programs.

Science.gov (United States)

Search, Kathryn R; Tolle, Susan L; McCombs, Gayle B; Arndt, Aaron

2018-02-01

Purpose: The purpose of this study was to survey entry-level dental hygiene program directors in the United States (U.S.) to assess their perceptions of dental hygienists with visible tattoos as well as to determine current policies related to dress codes in U.S. dental hygiene programs. Methods: Data was collected with an online survey emailed to 340 dental hygiene program directors yielding a 43% (n=141) response rate. Participants indicated their opinions of visible tattoos on the basis of professionalism and school policy satisfaction. Results: Eighty percent of respondents reported their program as having dress code policies on visible tattoos, with the majority (97%) requiring visible tattoos to be covered. Results revealed both students (M=5.57, phygiene faculty should discuss the impact of visible tattoos on future employment opportunities, and that the community would view the school as less professional if students had visible tattoos (pPersonal tolerance toward tattoos (phygiene program dress code included policy on visible tattoos. Conclusion: Study results showed that visible tattoos were not perceived favorably and that personal perceptions of dental hygiene program directors may have influenced school dress code polices regarding visible tattoos. These findings provide evidence based information for dental hygienists, students, faculty, administrators and hiring managers for formulating policies relating to body art. Copyright © 2018 The American Dental Hygienists’ Association.

Processing EOS MLS Level-2 Data

Science.gov (United States)

Snyder, W. Van; Wu, Dong; Read, William; Jiang, Jonathan; Wagner, Paul; Livesey, Nathaniel; Schwartz, Michael; Filipiak, Mark; Pumphrey, Hugh; Shippony, Zvi

2006-01-01

A computer program performs level-2 processing of thermal-microwave-radiance data from observations of the limb of the Earth by the Earth Observing System (EOS) Microwave Limb Sounder (MLS). The purpose of the processing is to estimate the composition and temperature of the atmosphere versus altitude from .8 to .90 km. "Level-2" as used here is a specialists f term signifying both vertical profiles of geophysical parameters along the measurement track of the instrument and processing performed by this or other software to generate such profiles. Designed to be flexible, the program is controlled via a configuration file that defines all aspects of processing, including contents of state and measurement vectors, configurations of forward models, measurement and calibration data to be read, and the manner of inverting the models to obtain the desired estimates. The program can operate in a parallel form in which one instance of the program acts a master, coordinating the work of multiple slave instances on a cluster of computers, each slave operating on a portion of the data. Optionally, the configuration file can be made to instruct the software to produce files of simulated radiances based on state vectors formed from sets of geophysical data-product files taken as input.

Use of inexpensive pressure transducers for measuring water levels in wells

Science.gov (United States)

Keeland, B.D.; Dowd, J.F.; Hardegree, W.S.

1997-01-01

Frequent measurement of below ground water levels at multiple locations is an important component of many wetland ecosystem studies. These measurements, however, are usually time consuming, labor intensive, and expensive. This paper describes a water-level sensor that is inexpensive and easy to construct. The sensor is placed below the expected low water level in a shallow well and, when connected to a datalogger, uses a pressure transducer to detect groundwater or surface water elevations. Details of pressure transducer theory, sensor construction, calibration, and examples of field installations are presented. Although the transducers must be individually calibrated, the sensors have a linear response to changing water levels (r2 ??? .999). Measurement errors resulting from temperature fluctuations are shown to be about 4 cm over a 35??C temperature range, but are minimal when the sensors are installed in groundwater wells where temperatures are less variable. Greater accuracy may be obtained by incorporating water temperature data into the initial calibration (0.14 cm error over a 35??C temperature range). Examples of the utility of these sensors in studies of groundwater/surface water interactions and the effects of water level fluctuations on tree growth are provided. ?? 1997 Kluwer Academic Publishers.

Optimal Fasting Time before Measurement of Serum Triglyceride Levels in Healthy Volunteers.

Science.gov (United States)

Pongsuthana, Surapun; Tivatunsakul, Naris

2016-02-01

Coronary heart disease is a major public health problem. Elevated triglyceride levels are a risk factor for atherosclerosis and coronary heart disease. Food intake interferes with the measurement of serum triglyceride levels, and in previous studies, fasting for 12 hours was recommended before blood sampling. In real-world practice, long fasting times cause patient discomfort and poor compliance, and the present study was, therefore, designed to determine the appropriate fasting time prior to measuring serum triglyceride levels. To determine the appropriate fasting time before measuring serum triglyceride levels. This was a pilot study performed using healthy volunteers aged between 20 and 30 years old from November 2013 to December 2013 at Rajavithi Hospital. The first blood sample was measured in the morning after fasting over 12 hours. The subjects then took their regular breakfast, after which they fasted for 8 hours. Blood samples were taken 6 and 8 hours later and sent to the laboratory for measurement of serum triglyceride levels. 40 volunteers, of whom 25 were female, were enrolled. Their mean age was 25.9 ± 2.81 years old, and their mean weight, height, and body mass index were 61.5 ± 12.5 kg, 167.2 ± 8.3 cm and 21.84 ± 3.1 kg/m2, respectively. Mean fasting serum triglyceride level at 12 hours was 80.23 ± 36.33 mg/dl, at 6 hours it was 110.65 ± 73.45 mg/dl, and at 8 hours it was 75.62 ± 46.81 mg/dl. The group fasting for 12 hours had significantly lower serum triglyceride levels than the group fasting for 6 hours (p-value = 0.003), but no significant difference was found between the group fasting for 12 hours and the one fasting for 8 hours (p-value = 0.493). The present study showed no significant difference in triglyceride levels in patients who had fasted or 8 hours and those who had done so for 12 hours. Fasting for only 8 hours before measurement of serum triglyceride may be sufficient.

Technology readiness levels for the new millennium program

Science.gov (United States)

Moynihan, P. I.; Minning, C. P.; Stocky, J. F.

2003-01-01

NASA's New Millennium Program (NMP) seeks to advance space exploration by providing an in-space validating mechanism to verify the maturity of promising advanced technologies that cannot be adequately validated with Earth-based testing alone. In meeting this objective, NMP uses NASA Technology Readiness Levels (TRL) as key indicators of technology advancement and assesses development progress against this generalized metric. By providing an opportunity for in-space validation, NMP can mature a suitable advanced technology from TRL 4 (component and/or breadboard validation in laboratory environment) to a TRL 7 (system prototype demonstrated in an Earth-based space environment). Spaceflight technology comprises a myriad of categories, types, and functions, and as each individual technology emerges, a consistent interpretation of its specific state of technological advancement relative to other technologies is problematic.

Tutorial and Guidelines on Measurement of Sound Pressure Level in Voice and Speech

Science.gov (United States)

Švec, Jan G.; Granqvist, Svante

2018-01-01

Purpose: Sound pressure level (SPL) measurement of voice and speech is often considered a trivial matter, but the measured levels are often reported incorrectly or incompletely, making them difficult to compare among various studies. This article aims at explaining the fundamental principles behind these measurements and providing guidelines to…

Individual v. community-level measures of women's decision-making ...

African Journals Online (AJOL)

Individual v. community-level measures of women's decision-making involvement and ... participation for child survival in sub-Saharan Africa is limited. ... Multilevel discrete-time hazard models were employed to investigate the net effect of ...

DUQuE quality management measures: associations between quality management at hospital and pathway levels.

Science.gov (United States)

Wagner, Cordula; Groene, Oliver; Thompson, Caroline A; Dersarkissian, Maral; Klazinga, Niek S; Arah, Onyebuchi A; Suñol, Rosa

2014-04-01

The assessment of integral quality management (QM) in a hospital requires measurement and monitoring from different perspectives and at various levels of care delivery. Within the DUQuE project (Deepening our Understanding of Quality improvement in Europe), seven measures for QM were developed. This study investigates the relationships between the various quality measures. It is a multi-level, cross-sectional, mixed-method study. As part of the DUQuE project, we invited a random sample of 74 hospitals in 7 countries. The quality managers of these hospitals were the main respondents. Furthermore, data of site visits of external surveyors assessing the participating hospitals were used. Three measures of QM at hospitals level focusing on integral systems (QMSI), compliance with the Plan-Do-Study-Act quality improvement cycle (QMCI) and implementation of clinical quality (CQII). Four measures of QM activities at care pathway level focusing on Specialized expertise and responsibility (SER), Evidence-based organization of pathways (EBOP), Patient safety strategies (PSS) and Clinical review (CR). Positive significant associations were found between the three hospitals level QM measures. Results of the relationships between levels were mixed and showed most associations between QMCI and department-level QM measures for all four types of departments. QMSI was associated with PSS in all types of departments. By using the seven measures of QM, it is possible to get a more comprehensive picture of the maturity of QM in hospitals, with regard to the different levels and across various types of hospital departments.

Reading assessment and training program

International Nuclear Information System (INIS)

Lewis, C.L.

1991-01-01

The objective was to ensure ourselves and the general public that the workers in the Nuclear Materials Processing Department (NMPD) could read, follow, and understand procedures. Procedures were randomly selected and analyzed for reading levels. A tenth grade reading level was established as the standard for all NMPD employees. Employees were tested to determine reading levels and approximately 12% could not read at the target level. A Procedure Walk-Through Evaluation was administered to each person not reaching tenth grade reading level. This was a job performance measure given to ensure that the worker was competent in his/her present job, and should remain there while completing reading training. A mandatory Reading Training Program utilizing Computer Based Training was established. This program is self-paced, individualized instruction and provided to the worker on Company time. Results of the CBT Program have been very good. Instruction is supplemented with test-taking skills seminars, practice exams, individual conferences with their own reading specialist, and some self-directed study books. This paper describes the program at Savannah River Site

Development of capacitive sensor for automatically measuring tumbler water level with FEA simulation.

Science.gov (United States)

Wei, Qun; Kim, Mi-Jung; Lee, Jong-Ha

2018-01-01

Drinking water has several advantages that have already been established, such as improving blood circulation, reducing acid in the stomach, etc. However, due to people not noticing the amount of water they consume every time they drink, most people drink less water than the recommended daily allowance. In this paper, a capacitive sensor for developing an automatic tumbler to measure water level is proposed. Different than in previous studies, the proposed capacitive sensor was separated into two sets: the main sensor for measuring the water level in the tumbler, and the reference sensor for measuring the incremental level unit. In order to confirm the feasibility of the proposed idea, and to optimize the shape of the sensor, a 3D model of the capacitive sensor with the tumbler was designed and subjected to Finite Element Analysis (FEA) simulation. According to the simulation results, the electrodes were made of copper and assembled in a tumbler manufactured by a 3D printer. The tumbler was filled with water and was subjected to experiments in order to assess the sensor's performance. The comparison of experimental results to the simulation results shows that the measured capacitance value of the capacitive sensor changed linearly as the water level varied. This proves that the proposed sensor can accurately measure the water level in the tumbler. Additionally, by use of the curve fitting method, a compensation algorithm was found to match the actual level with the measured level. The experimental results proved that the proposed capacitive sensor is able to measure the actual water level in the tumbler accurately. A digital control part with micro-processor will be designed and fixed on the bottom of the tumbler for developing a smart tumbler.

Measuring patient safety culture: an assessment of the clustering of responses at unit level and hospital level

NARCIS (Netherlands)

Smits, M.; Wagner, C.; Spreeuwenberg, P.; Wal, van der G.

2009-01-01

OBJECTIVES: To test the claim that the Hospital Survey on Patient Safety Culture (HSOPS) measures patient safety culture instead of mere individual attitudes and to determine the most appropriate level (individual, unit or hospital level) for interventions aimed at improving the culture of patient

Measuring patient safety culture : an assessment of the clustering of responses at unit level and hospital level

NARCIS (Netherlands)

Smits, M.; Wagner, C.; Spreeuwenberg, P.; Wal, G. van der; Groenewegen, P.P.

2009-01-01

Objectives: To test the claim that the Hospital Survey on Patient Safety Culture (HSOPS) measures patient safety culture instead of mere individual attitudes and to determine the most appropriate level (individual, unit or hospital level) for interventions aimed at improving the culture of patient

The Implementation Leadership Scale (ILS): development of a brief measure of unit level implementation leadership.

Science.gov (United States)

Aarons, Gregory A; Ehrhart, Mark G; Farahnak, Lauren R

2014-04-14

In healthcare and allied healthcare settings, leadership that supports effective implementation of evidenced-based practices (EBPs) is a critical concern. However, there are no empirically validated measures to assess implementation leadership. This paper describes the development, factor structure, and initial reliability and convergent and discriminant validity of a very brief measure of implementation leadership: the Implementation Leadership Scale (ILS). Participants were 459 mental health clinicians working in 93 different outpatient mental health programs in Southern California, USA. Initial item development was supported as part of a two United States National Institutes of Health (NIH) studies focused on developing implementation leadership training and implementation measure development. Clinician work group/team-level data were randomly assigned to be utilized for an exploratory factor analysis (n = 229; k = 46 teams) or for a confirmatory factor analysis (n = 230; k = 47 teams). The confirmatory factor analysis controlled for the multilevel, nested data structure. Reliability and validity analyses were then conducted with the full sample. The exploratory factor analysis resulted in a 12-item scale with four subscales representing proactive leadership, knowledgeable leadership, supportive leadership, and perseverant leadership. Confirmatory factor analysis supported an a priori higher order factor structure with subscales contributing to a single higher order implementation leadership factor. The scale demonstrated excellent internal consistency reliability as well as convergent and discriminant validity. The ILS is a brief and efficient measure of unit level leadership for EBP implementation. The availability of the ILS will allow researchers to assess strategic leadership for implementation in order to advance understanding of leadership as a predictor of organizational context for implementation. The ILS also holds promise as a tool for

The implementation leadership scale (ILS): development of a brief measure of unit level implementation leadership

Science.gov (United States)

2014-01-01

Background In healthcare and allied healthcare settings, leadership that supports effective implementation of evidenced-based practices (EBPs) is a critical concern. However, there are no empirically validated measures to assess implementation leadership. This paper describes the development, factor structure, and initial reliability and convergent and discriminant validity of a very brief measure of implementation leadership: the Implementation Leadership Scale (ILS). Methods Participants were 459 mental health clinicians working in 93 different outpatient mental health programs in Southern California, USA. Initial item development was supported as part of a two United States National Institutes of Health (NIH) studies focused on developing implementation leadership training and implementation measure development. Clinician work group/team-level data were randomly assigned to be utilized for an exploratory factor analysis (n = 229; k = 46 teams) or for a confirmatory factor analysis (n = 230; k = 47 teams). The confirmatory factor analysis controlled for the multilevel, nested data structure. Reliability and validity analyses were then conducted with the full sample. Results The exploratory factor analysis resulted in a 12-item scale with four subscales representing proactive leadership, knowledgeable leadership, supportive leadership, and perseverant leadership. Confirmatory factor analysis supported an a priori higher order factor structure with subscales contributing to a single higher order implementation leadership factor. The scale demonstrated excellent internal consistency reliability as well as convergent and discriminant validity. Conclusions The ILS is a brief and efficient measure of unit level leadership for EBP implementation. The availability of the ILS will allow researchers to assess strategic leadership for implementation in order to advance understanding of leadership as a predictor of organizational context for implementation

Legacy Risk Measure for Environmental Waste

International Nuclear Information System (INIS)

Eide, S. A.; Nitschke, R. L.

2002-01-01

The Idaho National Engineering and Environmental Laboratory (INEEL) is investigating the development of a comprehensive and quantitative risk model framework for environmental management activities at the site. Included are waste management programs (high-level waste, transuranic waste, low-level waste, mixed low-level waste, spent nuclear fuel, and special nuclear materials), major environmental restoration efforts, major decontamination and decommissioning projects, and planned long-term stewardship activities. Two basic types of risk estimates are included: risks from environmental management activities, and long-term legacy risks from wastes/materials. Both types of risks are estimated using the Environment, Safety, and Health Risk Assessment Program (ESHRAP) developed at the INEEL. Given these two types of risk calculations, the following evaluations can be performed: risk evaluation of an entire program (covering waste/material as it now exists through disposal or other e nd states); risk comparisons of alternative programs or activities; comparisons of risk benefit versus risk cost for activities or entire programs; ranking of programs or activities by risk; ranking of wastes/materials by risk; evaluation of site risk changes with time as activities progress; and integrated performance measurement using indicators such as injury/death and exposure rates. This paper discusses the definition and calculation of legacy risk measures and associated issues. The legacy risk measure is needed to support three of the seven types of evaluations listed above: comparisons of risk benefit versus risk cost, ranking of wastes/materials by risk, and evaluation of site risk changes with time

The Leaders across Borders Certification Program—A Systemic Multiple Level Observation of Groups Analysis Approach to Measure Effective Leadership: A Case Study

Directory of Open Access Journals (Sweden)

Ricardo Hirata-Okamoto

2017-10-01

Full Text Available Leadership measurement, feedback, and development have grown in importance for the field of management. The Mexico–US Border defined as the area of land within 100 km (62.5 miles north and south of the international boundary, shares common challenges, and requires the development of multicultural change agents who conduct binational actions toward the improvement of public health and quality of life of the population in the region. Leaders across Borders (LaB was established in 2010 as an advanced certified binational leadership development program aimed at building the capacity of public health, health care, and other community sector leaders working to improve the health of the communities in the Mexico–US Border region. Leadership as a social interaction process requires leader skills development to achieve goals promoting unity and reducing polarization to optimize interactions between all resources, thus improving teamwork. Therefore, measurement and feedback model of general values and beliefs that guide effective behavior, not only individual personality assessments need to drive a proactive learning and action plan development to improve interactions in a team, thus optimizing leadership. Starting 2014, we administered a new model named Systemic Multiple Level Observation of Groups (SYMLOG to measure the values and beliefs that guide the behavior of learners and team facilitators. We also evaluated the effectiveness of each team of the program and established benchmarks and action plans to optimize interactions and communication between all the learners during the 8-month program. This leads to a stronger systemic network upon graduation from the program. The SYMLOG approach measured initial and improved situations of individual leadership and team performance effectiveness because of the LaB Program training and skills development sessions. The SYMLOG also provided positive feedback to each participant, which had a direct impact

An approach for the accurate measurement of social morality levels.

Science.gov (United States)

Liu, Haiyan; Chen, Xia; Zhang, Bo

2013-01-01

In the social sciences, computer-based modeling has become an increasingly important tool receiving widespread attention. However, the derivation of the quantitative relationships linking individual moral behavior and social morality levels, so as to provide a useful basis for social policy-making, remains a challenge in the scholarly literature today. A quantitative measurement of morality from the perspective of complexity science constitutes an innovative attempt. Based on the NetLogo platform, this article examines the effect of various factors on social morality levels, using agents modeling moral behavior, immoral behavior, and a range of environmental social resources. Threshold values for the various parameters are obtained through sensitivity analysis; and practical solutions are proposed for reversing declines in social morality levels. The results show that: (1) Population size may accelerate or impede the speed with which immoral behavior comes to determine the overall level of social morality, but it has no effect on the level of social morality itself; (2) The impact of rewards and punishment on social morality levels follows the "5∶1 rewards-to-punishment rule," which is to say that 5 units of rewards have the same effect as 1 unit of punishment; (3) The abundance of public resources is inversely related to the level of social morality; (4) When the cost of population mobility reaches 10% of the total energy level, immoral behavior begins to be suppressed (i.e. the 1/10 moral cost rule). The research approach and methods presented in this paper successfully address the difficulties involved in measuring social morality levels, and promise extensive application potentials.

Adult tobacco use levels after intensive tobacco control measures: New York City, 2002-2003.

Science.gov (United States)

Frieden, Thomas R; Mostashari, Farzad; Kerker, Bonnie D; Miller, Nancy; Hajat, Anjum; Frankel, Martin

2005-06-01

We sought to determine the impact of comprehensive tobacco control measures in New York City. In 2002, New York City implemented a tobacco control strategy of (1) increased cigarette excise taxes; (2) legal action that made virtually all work-places, including bars and restaurants, smoke free; (3) increased cessation services, including a large-scale free nicotine-patch program; (4) education; and (5) evaluation. The health department also began annual surveys on a broad array of health measures, including smoking. From 2002 to 2003, smoking prevalence among New York City adults decreased by 11% (from 21.6% to 19.2%, approximately 140000 fewer smokers). Smoking declined among all age groups, race/ethnicities, and education levels; in both genders; among both US-born and foreign-born persons; and in all 5 boroughs. Increased taxation appeared to account for the largest proportion of the decrease; however, between 2002 and 2003 the proportion of cigarettes purchased outside New York City doubled, reducing the effective price increase by a third. Concerted local action can sharply reduce smoking prevalence. However, further progress will require national action, particularly to increase cigarette taxes, reduce cigarette tax evasion, expand education and cessation services, and limit tobacco marketing.

Modeling the population-level effects of male circumcision as an HIV-preventive measure: a gendered perspective.

Directory of Open Access Journals (Sweden)

Jonathan Dushoff

Full Text Available BACKGROUND: Evidence from biological, epidemiological, and controlled intervention studies has demonstrated that male circumcision (MC protects males from HIV infection, and MC is now advocated as a public-health intervention against HIV. MC provides direct protection only to men, but is expected to provide indirect protection to women at risk of acquiring HIV from heterosexual transmission. How such indirect protection interacts with the possibility that MC campaigns will lead to behavior changes, however, is not yet well understood. Our objective here is to investigate the link between individual-level effects of MC campaigns and long-term population-level outcomes resulting from disease dynamics, looking at both genders separately, over a broad range of parameters. METHODS AND FINDINGS: We use simple mathematical models of heterosexual transmission to investigate the potential effects of a circumcision scale-up, combined with possible associated behavioral disinhibition. We examine patterns in expected long-term prevalence using a simple equilibrium model based on transmission factors, and validate our results with ODE-based simulations, focusing on the link between effects on females and those on males.We find that the long-term population-level effects on females and males are not strongly linked: there are many possible ways in which an intervention which reduces prevalence in males might nonetheless increase prevalence in females. CONCLUSIONS: Since an intervention that reduces long-term male prevalence could nonetheless increase long-term female prevalence, MC campaigns should explicitly consider both the short-term and long-term effects of MC interventions on females. Our findings strongly underline the importance of pairing MC programs with education, support programs and HIV testing and counseling, together with other prevention measures.

An interprofessional palliative care oncology rehabilitation program: effects on function and predictors of program completion.

Science.gov (United States)

Chasen, M R; Feldstain, A; Gravelle, D; Macdonald, N; Pereira, J

2013-12-01

After treatment, patients with active cancer face a considerable burden from the effects of both the disease and its treatment. The Palliative Rehabilitation Program (prp) is designed to ameliorate disease effects and to improve the patient's functioning. The present study evaluated predictors of program completion and changes in functioning, symptoms, and well-being after the program. The program received referrals for 173 patients who had finished anticancer therapy. Of those 173 patients, 116 with advanced cancer were eligible and enrolled in the 8-week interprofessional prp; 67 completed it. Measures of physical, nutritional, social, and psychological functioning were evaluated at entry to the program and at completion. Participants experienced significant improvements in physical performance (p program not challenging enough), death, and personal or unknown reasons. A normal level of C-reactive protein (program completion. Patients living with advanced cancers who underwent the interprofessional prp experienced significant improvement in functioning across several domains. Program completion can be predicted by a normal level of C-reactive protein.

Penn State continuing education program on low-level radioactive waste disposal and management: lessons learned

International Nuclear Information System (INIS)

Vincenti, J.R.

1985-01-01

Since November of 1983, The Pennsylvania State University, Institute for Research on Land and Water Resources has provided the citizens of the Commonwealth of Pennsylvania with information on low-level radioactive waste disposal and management through a continuing education program called the PIER (Public Involvement and Education on Radiation) Program. This paper will review the form, function, and development of this continuing education program and some of the lessons learned in providing citizens of the Commonwealth with information in both formal and informal educational settings

Measuring Structural Gender Equality in Mexico: A State Level Analysis

Science.gov (United States)

Frias, Sonia M.

2008-01-01

The main goal of this article is to assess the level of gender equality across the 32 Mexican states. After reviewing conceptual and methodological issues related to previous measures of structural inequality I detail the logic and methodology involved in the construction of a composite and multidimensional measure of gender equality, at the…

SPSS and SAS programs for addressing interdependence and basic levels-of-analysis issues in psychological data.

Science.gov (United States)

O'Connor, Brian P

2004-02-01

Levels-of-analysis issues arise whenever individual-level data are collected from more than one person from the same dyad, family, classroom, work group, or other interaction unit. Interdependence in data from individuals in the same interaction units also violates the independence-of-observations assumption that underlies commonly used statistical tests. This article describes the data analysis challenges that are presented by these issues and presents SPSS and SAS programs for conducting appropriate analyses. The programs conduct the within-and-between-analyses described by Dansereau, Alutto, and Yammarino (1984) and the dyad-level analyses described by Gonzalez and Griffin (1999) and Griffin and Gonzalez (1995). Contrasts with general multilevel modeling procedures are then discussed.

Organization of the two-level memory in the image processing system on scanning measuring projectors

International Nuclear Information System (INIS)

Sychev, A.Yu.

1977-01-01

Discussed are the problems of improving the efficiency of the system for processing pictures taken in bubble chambers with the use of scanning measuring projectors. The system comprises 20 to 30 pro ectors linked with the ICL-1903A computer provided with a mainframe memory, 64 kilobytes in size. Because of the insufficient size of a mainframe memory, a part of the programs and data is located in a second-level memory, i.e. in an external memory. The analytical model described herein is used to analyze the effect of the memory organization on the characteristics of the system. It is shown that organization of pure procedures and introduction of the centralized control of the tWo-leVel memory result in substantial improvement of the efficiency of the picture processing system

Four themes that underlie the high-level nuclear waste management program

International Nuclear Information System (INIS)

Sprecher, W.M.

1989-01-01

In 1982, after years of deliberation and in response to mounting pressures from environmental, industrial, and other groups, the US Congress enacted the Nuclear Waste Policy Act (NWPA) of 1982, which was signed into law by the President in January 1983. That legislation signified a major milestone in the nation's management of high-level nuclear waste, since it represented a consensus among the nation's lawmakers to tackle a problem that had evaded solution for decades. Implementation of the NWPA has proven to be exceedingly difficult, as attested by the discord generated by the US Department of Energy's (DOE's) geologic repository and monitored retrievable storage (MRS) facility siting activities. The vision that motivated the crafters of the 1982 act became blurred as opposition to the law increased. After many hearings that underscored the public's concern with the waste management program, the Congress enacted the Nuclear Waste Policy Amendments Act of 1987 (Amendments Act), which steamlined and focused the program, while establishing three independent bodies: the MRS Review Commission, the Nuclear Waste Technical Review Board, and the Office of the Nuclear Waste Negotiator. Yet, even as the program evolves, several themes characterizing the nation's effort to solve the waste management problem continue to prevail. The first of these themes has to do with social consciousness, and the others that follow deal with technical leadership, public involvement and risk perceptions, and program conservatism

Monitoring program for evaluating radionuclide emissions from incineration of low-level radioactive waste

International Nuclear Information System (INIS)

Wittmer, S.C.; Solomon, H.F.

1984-01-01

The implementation of an incineration program for low-level radioactive waste is a complex task, especially in the area of obtaining environmental permits. To provide assurance to the appropriate regulatory agencies involved with environmental permitting and others that an incineration program is properly conducted, emissions monitoring to identify radionuclides and their fate may be needed. An electronic spreadsheet software program Lotus 1-2-3 (Lotus Development Corporation) on an IBM Personal Computer has been used to perform data reduction for test results from such a monitoring program and to present them graphically to facilitate interpretation. The sampling technique includes: (1) the use of an EPA Method 5 stack sampling train modified to exclude the dry-catch filtration assembly with ethanolamine used to scrub incinerator gas at depressed temperatures and (2) a continuous composite liquid sampler for incinerator wet scrubber discharge to the sanitary sewer. Radionuclides in the samples are assayed using scintillation spectrometry

An integrated approach to strategic planning in the civilian high-level radioactive waste management program

International Nuclear Information System (INIS)

Sprecher, W.M.; Katz, J.; Redmond, R.J.

1992-01-01

This paper describes the approach that the Office of Civilian Radioactive Waste Management (OCRWM) of the Department of Energy (DOE) is taking to the task of strategic planning for the civilian high-level radioactive waste management program. It highlights selected planning products and activities that have emerged over the past year. It demonstrates that this approach is an integrated one, both in the sense of being systematic on the program level but also as a component of DOE strategic planning efforts. Lastly, it indicates that OCRWM strategic planning takes place in a dynamic environment and consequently is a process that is still evolving in response to the demands placed upon it

Grade Level and Gender Differences in a School-Based Reading Tutoring Program

Science.gov (United States)

Chang, Sau Hou

2011-01-01

The purpose of the present study is to investigate the grade level and gender differences in a school-based reading tutoring program. The treatment group included 10 first-grade and 12 second-grade struggling readers, and the control group included 41 first-grade and 63 second-grade nonstruggling readers. The tutors were teacher candidates in an…

Using Overall Equipment Effectiveness indicator to measure the level of planned production time usage of sewing machine

Directory of Open Access Journals (Sweden)

Marek Krynke

2014-12-01

Full Text Available The chapter presents the results of utilization of the OEE indicator to measure the level of operating time usage of sewing machine production of air bags. The idea of an OEE indictor, which is a key metrics in Total Productive Maintenance (TPM program, is presented. The goals and benefits of its calculation are included. The research object – KL 110 air bags sewing machine - what for the machine is used. The calculation of TPM indicators for the analysed machine is presented. The calculation of TPM indicators was undertaken over a period of six months of the machine’s working time. It was indicated that the overall effectiveness of the machine is at a level of 65,7%, the time losses were 34,3%. Most of the losses were related to low performance. Only Availability indicator reaches a word class level, if other indicators such as Performance, Quality and OEE should be improved, their value should be increased. Activities to improve the effectiveness of the machine utilization were determined.

NASA's Optical Measurement Program 2014

Science.gov (United States)

Cowardin, H.; Lederer, S.; Stansbery, G.; Seitzer, P.; Buckalew, B.; Abercromby, K.; Barker, E.

2014-01-01

The Optical Measurements Group (OMG) within the NASA Orbital Debris Program Office (ODPO) addresses U.S. National Space Policy goals by monitoring and characterizing debris. Since 2001, the OMG has used the Michigan Orbital Debris Survey Telescope (MODEST) at Cerro Tololo Inter-American Observatory (CTIO) in Chile for general orbital debris survey. The 0.6-m Schmidt MODEST provides calibrated astronomical data of GEO targets, both catalogued and uncatalogued debris, with excellent image quality. The data are utilized by the ODPO modeling group and are included in the Orbital Debris Engineering Model (ORDEM) v. 3.0. MODEST and the CTIO/SMARTS (Small and Moderate Aperture Research Telescope System) 0.9 m both acquire filter photometric data, as well as synchronously observing targets in selected optical filters. This information provides data used in material composition studies as well as longer orbital arc data on the same target, without time delay or bias from a rotating, tumbling, or spinning target. NASA, in collaboration with the University of Michigan, began using the twin 6.5-m Magellan telescopes at Las Campanas Observatory in Chile for deep imaging (Baade) and spectroscopic data (Clay) in 2011. Through the data acquired on Baade, debris have been detected that are 3 magnitudes fainter than detections with MODEST, while the data from Clay provide better resolved information used in material characterization analyses via selected bandpasses. To better characterize and model optical data, the Optical Measurements Center (OMC) at NASA/JSC has been in operation since 2005, resulting in a database of comparison laboratory data. The OMC is designed to emulate illumination conditions in space using equipment and techniques that parallel telescopic observations and source-target-sensor orientations. Lastly, the OMG is building the Meter Class Autonomous Telescope (MCAT) at Ascension Island. The 1.3-m telescope is designed to observe GEO and LEO targets, using a

Level measurements part 2[5 figs]; Nivaamaalinger del 2

Energy Technology Data Exchange (ETDEWEB)

Gundersen, Thor Ole

2006-07-01

The article discusses various level measurement methods other than using ultrasound that was discussed in part 1 of the article series. Methods using laser, capacity, weight and displacement are presented. Various life span aspects of the machinery are discussed.

Instructions for 104-SX liquid level measurement field tests

International Nuclear Information System (INIS)

Webb, R.H.

1994-01-01

This document provides detailed instructions for field testing a suggested solution of inserting a liner inside the 104-SX failed Liquid Observation Well to gain access for making temporary Liquid Level Measurement until a permanent solution has been provided

An ultrasound mini-balance for measurement of therapy level ultrasound