WorldWideScience

Sample records for legal-weight truck scenario

  1. TITAN Legal Weight Truck cask preliminary design report

    International Nuclear Information System (INIS)

    1990-04-01

    The Preliminary Design of the TITAN Legal Weight Truck (LWT) Cask System and Ancillary Equipment is presented in this document. The scope of the document includes the LWT cask with fuel baskets; impact limiters, and lifting and tiedown features; the cask support system for transportation; intermodal transfer skid; personnel barrier; and cask lifting yoke assembly. 75 figs., 48 tabs

  2. TITAN Legal Weight Truck cask preliminary design report

    International Nuclear Information System (INIS)

    1990-04-01

    The Preliminary Design of the TITAN Legal Weight Truck (LWT) Cask System and Ancillary Equipment is presented in this document. The scope of this document includes the LWT cask with fuel baskets, impact limiters, and lifting and tiedown features; the cask support system for transportation; intermodal transfer skid; personnel barrier; and cask lifting yoke assembly. The results of the tradeoff studies and evaluations that were performed during the preliminary design are presented in Appendix A to this report. 51 figs., 17 tabs

  3. Legal weight truck cask model impact limiter response

    International Nuclear Information System (INIS)

    Meinert, N.M.; Shappert, L.B.

    1989-01-01

    Dynamic and quasi-static quarter-scale model testing was performed to supplement the analytical case presented in the Nuclear Assurance Corporation Legal Weight Truck (NAC LWT) cask transport licensing application. Four successive drop tests from 9.0 meters (30 feet) onto an unyielding surface and one 1.0-meter (40-inch) drop onto a scale mild steel pin 3.8 centimeters (1.5 inches) in diameter, corroborated the impact limiter design and structural analyses presented in the licensing application. Quantitative measurements, made during drop testing, support the impact limiter analyses. High-speed photography of the tests confirm that only a small amount of energy is elastically stored in the aluminum honeycomb and that oblique drop slapdown is not significant. The qualitative conclusion is that the limiter protected LWT cask will not sustain permanent structural damage and containment will be maintained, subsequent to a hypothetical accident, as shown by structural analyses

  4. GA-4 and GA-9 legal weight truck shipping cask development

    International Nuclear Information System (INIS)

    Grenier, R.M.; Meyer, R.J.; Jensen, M.F.

    1989-02-01

    We are developing two new legal weight truck spent fuel shipping casks that will carry four PWR or nine BWR spent fuel assemblies. They are being developed to meet requirements to dispose of nuclear wastes at a permanent disposal site. Our primary goal is to maximize the number of fuel elements of each fuel type that a legal weight truck (LWT) cask can carry, while ensuring that the design meets all NRC licensing requirements. 1 ref., 4 figs

  5. GA-4 and GA-9 legal weight truck shipping cask development

    International Nuclear Information System (INIS)

    Grenier, R.; Meyer, R.; Jensen, M.

    1989-01-01

    General Atomics (GA), under contract to the Idaho Operations Office of the U.S. Department of Energy, is developing two new legal weight truck spent fuel shipping casks that will carry four PWR or nine BWR spent fuel assemblies. They are being developed for the Office of Civilian Radioactive Waste Management (OCRWM) to meet its mission to dispose of nuclear wastes at a permanent disposal site. This paper discusses the primary goal, to maximize the number of fuel elements of each fuel type that a LWT cask can carry, while ensuring that the design meets all NRC licensing requirements

  6. Transport package response to severe thermal events, part 2: legal weight truck cask

    International Nuclear Information System (INIS)

    Greiner, M.; Faulkner, R.J.; Jin, Y.Y.

    1998-01-01

    The response of intact and damaged versions of the GA-4 Legal Weight Truck Cask to a range of severe thermal events is simulated using finite element computer analysis. The minimum fire durations that cause the containment seals and fuel cladding to reach their respective temperature limits are evaluated for a range of hydrocarbon fire temperatures. Containment seals reach their temperature limit in shorter duration fires as compared to the cladding, for both an undamaged package and a cask whose impact limiter is destroyed moments before the fire begins. However, if the neutron shield is destroyed, the cladding reaches its limit first in high temperature fires. A margin of safety exists between the conditions of the IAEA regulatory fire test and all of the performance envelopes calculated in this work. (author)

  7. GA-4/GA-9 legal weight truck from reactor spent fuel shipping casks

    International Nuclear Information System (INIS)

    1990-04-01

    The preliminary design report presents the results of General Atomics (GA) preliminary design effort to develop weight truck from reactor spent fuel shipping casks. The thermal evaluation of the Office of Civilian Radioactive Waste Management (OCRWM) cask considered normal and hypothetical accident conditions of transport. We employed analytical modeling as well as fire testing of the neutron shielding material to perform the evaluation. This document addresses the thermal design features of the cask, discusses thermal criteria, and summarizes the results of the thermal evaluation, as well as results of structural containment and nuclear evaluations that support the design. Also included are the results of trade-off studies. 69 refs., 103 figs., 76 tabs

  8. Impacts of the use of spent nuclear fuel burnup credit on DOE advanced technology legal weight truck cask GA-4 fleet size

    International Nuclear Information System (INIS)

    Mobasheran, A.S.; Boshoven, J.; Lake, B.

    1995-01-01

    The object of this paper is to study the impact of full and partial spent fuel burnup credit on the capacity of the Legal Weight Truck Spent Fuel Shipping Cask (GA-4) and to determine the numbers of additional spent fuel assemblies which could be accommodated as a result. The scope of the study comprised performing nuclear criticality safety scoping calculations using the SCALE-PC software package and the 1993 spent fuel database to determine logistics for number of spent fuel assemblies to be shipped. The results of the study indicate that more capacity than 2 or 3 pressurized water reactor assemblies could be gained for GA-4 casks when burnup credit is considered. Reduction in GA-4 fleet size and number of shipments are expected to result from the acceptance of spent fuel burnup credit

  9. An empirical study of DSRC V2V performance in truck platooning scenarios

    Directory of Open Access Journals (Sweden)

    Song Gao

    2016-11-01

    Full Text Available Among many safety applications enabled by Dedicated Short Range Communication (DSRC, truck platooning provides many incentives to commercial companies. This paper studies DSRC Vehicle-to-Vehicle (V2V performance in truck platooning scenarios through real-world experiments. Commercial DSRC equipments and semi-trailer trucks are used in this study. We mount one DSRC antenna on each side of the truck. One set of dynamic tests and a few sets of static tests are conducted to explore DSRC behaviors under different situations. From the test results, we verified some of our speculations. For example, hilly roads can affect delivery ratio and antennas mounted on opposite sides of a truck can suffer from low delivery ratio at curved roads. In addition, we also found that antennas can sometimes suffer from low delivery ratio even when the trucks are on straight roads, possibly due to reflections from the nearby terrain. Fortunately, the delivery ratio can be greatly improved by using the two side antennas alternately.

  10. A scenarios study on future demands on container and truck sizes of the future

    NARCIS (Netherlands)

    B. Kraaijenhagen; Jan Jansen; H. Graser; Stef Weijers; I. Szylar

    2012-01-01

    To what extent will future demands of worldwide operating parties, regarding the (tertiary) packaging of their freight flows, determine or influence the future dimensions of freight trucks? That is the question we address to in this paper. In this study we have studied what container sizes may fit

  11. HEADWAY TIME AND CRASHES AMONG NOVICE TEENS AND EXPERIENCED ADULT DRIVERS IN A SIMULATED LEAD TRUCK BRAKING SCENARIO.

    Science.gov (United States)

    McDonald, Catherine C; Seacrist, Thomas S; Lee, Yi-Ching; Loeb, Helen; Kandadai, Venk; Winston, Flaura K

    2013-01-01

    Driving simulators can be used to evaluate driving performance under controlled, safe conditions. Teen drivers are at particular risk for motor vehicle crashes and simulated driving can provide important information on performance. We developed a new simulator protocol, the Simulated Driving Assessment (SDA), with the goal of providing a new tool for driver assessment and a common outcome measure for evaluation of training programs. As an initial effort to examine the validity of the SDA to differentiate performance according to experience, this analysis compared driving behaviors and crashes between novice teens (n=20) and experienced adults (n=17) on a high fidelity simulator for one common crash scenario, a rear-end crash. We examined headway time and crashes during a lead truck with sudden braking event in our SDA. We found that 35% of the novice teens crashed and none of the experienced adults crashed in this lead truck braking event; 50% of the teens versus 25% of the adults had a headway time braking. Among the 10 teens with brake pedal force when comparing teens who crashed, teens who did not crash and adults (none of whom crashed). Even with a relatively small sample, we found statistically significant differences in headway time for adults and teens, providing preliminary construct validation for our new SDA.

  12. The Bamberg Trucking Game: A Paradigm for Assessing the Detection of Win-Win Solutions in a Potential Conflict Scenario.

    Science.gov (United States)

    Nalis, Dario; Schütz, Astrid; Pastukhov, Alexander

    2018-01-01

    In win-win solutions, all parties benefit more from the solution than they would if they each pursued their own individual goals. Such solutions are beneficial at individual and collective levels and thus represent optimal solutions. Win-win solutions are desirable but often difficult to find. To allow the study of individual differences and situational factors that help or hinder the detection of win-win solutions, we created a paradigm that fills a gap in the repertoire of psychological instruments used to assess collaboration, cooperation, negotiation, and prosocial behavior. The new paradigm differs from previous ones in two aspects: (a) In existing paradigms that focus on social motivation, possible strategies are evident, whereas we focused here on the question of whether people can detect the solution and thus disentangle ability from motivation, (b) Paradigms that focus on cooperation typically entail a risk associated with the partner's defection, whereas cooperation in our paradigm is not associated with risk. We adjusted the Trucking Game-a method for assessing bargaining-to include a situation in which two parties can help each other achieve their respective goals and thus benefit over and above the pursuit of individual goals or compromising. We tested scenario-based and interaction-based versions with samples of 154 and 112 participants, respectively. Almost one third of the participants or dyads found the win-win solution. General mental abilities were not related to detecting the win-win solution in either version. The paradigm provides a way to extend research on cooperation and conflict and can thus be useful for research and training.

  13. Scenarios

    NARCIS (Netherlands)

    Pérez-Soba, Marta; Maas, Rob

    2015-01-01

    We cannot predict the future with certainty, but we know that it is influenced by our current actions, and that these in turn are influenced by our expectations. This is why future scenarios have existed from the dawn of civilization and have been used for developing military, political and economic

  14. Operational considerations in specifying legal weight vehicles for the highway transport of spent nuclear fuel

    International Nuclear Information System (INIS)

    Hill, C.V.; Rutenkroger, E.O.; Ratledge, J.E.

    1990-01-01

    This paper presents the results of a research project in which tractor manufacturers and carrier companies were interviewed to gather information on operational concerns in specifying a tractor to haul legal weight spent fuel casks. The system was assumed to operate very close to the 80,000 pound legal weight limit. Safety, performance, reliability, and maintainability of equipment were factors given particular attention. The interaction between driver fatigue, safety, and equipment was also discussed. Innovative operating strategies that could save weight were discussed. The paper concluded that operational considerations require that planners working with standard off-the-shelf tractor equipment should allow at least 17,350 pounds for the weight of the tractor as a starting point from which further weight reduction analysis can proceed. 4 refs., 3 figs

  15. Lift truck safety review

    Energy Technology Data Exchange (ETDEWEB)

    Cadwallader, L.C.

    1997-03-01

    This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter`s Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given.

  16. Lift truck safety review

    International Nuclear Information System (INIS)

    Cadwallader, L.C.

    1997-03-01

    This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter's Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given

  17. Overweight truck shipments to nuclear waste repositories: legal, political, administrative and operational considerations

    International Nuclear Information System (INIS)

    1986-03-01

    This report, prepared for the Chicago Operations Office and the Office of Civilian Radioactive Waste Management (OCRWM) of the US Department of Energy (DOE), identifies and analyzes legal, political, administrative, and operational issues that could affect an OCRWM decision to develop an overweight truck cask fleet for the commercial nuclear waste repository program. It also provides information required by DOE on vehicle size-and-weight administration and regulation, pertinent to nuclear waste shipments. Current legal-weight truck casks have a payload of one pressurized-water reactor spent fuel element or two boiling-water reactor spent fuel elements (1 PWR/2 BWR). For the requirements of the 1960s and 1970s, casks were designed with massive shielding to accommodate 6-month-old spent fuel; the gross vehicle weight was limited to 73,280 pounds. Spent fuel to be moved in the 1990s will have aged five years or more. Gross vehicle weight limitation for the Interstate highway system has been increased to 80,000 pounds. These changes allow the design of 25-ton legal-weight truck casks with payloads of 2 PWR/5 BWR. These changes may also allow the development of a 40-ton overweight truck cask with a payload of 4 PWR/10 BWR. Such overweight casks will result in significantly fewer highway shipments compared with legal-weight casks, with potential reductions in transport-related repository risks and costs. These advantages must be weighed against a number of institutional issues surrounding such overweight shipments before a substantial commitment is made to develop an overweight truck cask fleet. This report discusses these issues in detail and provides recommended actions to DOE

  18. Burnup credit applications in a high-capacity truck cask

    International Nuclear Information System (INIS)

    Boshoven, J.K.

    1992-09-01

    General Atomics (GA) has designed two legal weight truck (LWT) casks, the GA-4 and GA-9, to carry four pressurized-water-reactor (PWR) and nine boiling-water-reactor (BWR) fuel assemblies, respectively. GA plans to submit applications for certification to the US Nuclear Regulatory Commission (NRC) for the two casks in mid-1993. GA will include burnup credit analysis in the Safety Analysis Report for Packaging (SARP) for the GA-4 Cask. By including burnup credit in the criticality safety analysis for PWR fuels with initial enrichments above 3% U-235, public and occupation risks are reduced and cost savings are realized. The GA approach to burnup credit analysis incorporates the information produced in the US Department of Energy Burnup Credit Program. This paper describes the application of burnup credit to the criticality control design of the GA-4 Cask

  19. Work Truck Idling Reduction

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-03-01

    Hybrid utility trucks, with auxiliary power sources for on-board equipment, significantly reduce unnecessary idling resulting in fuel costs savings, less engine wear, and reduction in noise and emissions.

  20. Projection of light-truck population to year 2025

    Energy Technology Data Exchange (ETDEWEB)

    1978-10-01

    The recent growth in the number of light trucks is a matter of considerable interest in that it may have far-reaching implications for gasoline consumption. This paper forecasts the number of light trucks in the years to 2025. The forecast is based on economic scenarios developed by SRI International. Except for the case of the most-dismal economic forecast, the number of light trucks is predicted to increase monotonically and to show the greatest rate of increase between 1973 and 1980.

  1. 49 CFR 393.61 - Truck and truck tractor window construction.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Truck and truck tractor window construction. 393... REGULATIONS PARTS AND ACCESSORIES NECESSARY FOR SAFE OPERATION Glazing and Window Construction § 393.61 Truck and truck tractor window construction. Each truck and truck tractor (except trucks engaged in armored...

  2. Truck industry forum material.

    Science.gov (United States)

    2017-03-01

    The following PowerPoint presentation is the draft version of the presentation that would be used for : the upcoming half-day Infrastructure-Friendlier Trucks Forum tentatively scheduled for Friday, : March 13, 2015. This forum presented a project st...

  3. Truckstop -- and Truck!-- Electrification

    Energy Technology Data Exchange (ETDEWEB)

    Skip Yeakel

    2001-12-13

    The conclusions of this paper are: 0.5-1.5 G/H and/or BUSG/Y--how much time and money will it take to quantify and WHY BOTHER TO DO SO? No shortage of things to do re truckstop--+ truck!-- electrification; Better that government and industry should put many eggs in lots of baskets vs. all in one or few; Best concepts will surface as most viable; Economic appeal better than regulation or brute force; Launch Ground Freight Partnership and give it a chance to work; Demonstration is an effective means to educate, and learn from, customers--learning is a two way street; Research, Development, Demonstration, and Deployment (RD 3) are all important but only deployment gets results; TSE can start small in numbers of spaces to accommodate economically inspired growth but upfront plans should be made for expansion if meaningful idle reduction is to follow via TE; 110VAC 15A service/ parking space is minimal--if infrastructure starts like this, upfront plans must be made to increase capacity; Increased electrification of truckstop and truck alike will result in much better life on the road; Improved sleep will improve driver alertness and safety; Reduced idling will significantly reduce fuel use and emissions; Universal appeal for DOD, DOE, DOT, EPA, OEMs, and users alike; Clean coal, gas, hydro, nuclear, or wind energy sources are all distinctly American means by which to generate electricity; Nothing can compete with diesel fuel to serve mobile truck needs; stationary trucks are like power plants--they don't move and should NOT be powered by petroleum products whenever possible; Use American fueled power plants--electricity--to serve truck idling needs wherever practical to do so; encourage economic aspect; Create and reward industry initiatives to reduce fuel use; Eliminate FET on new trucks, provide tax credits (non highway fuel use and investment), provide incentives based on results; Encourage newer/ cleaner truck use; solicit BAAs with mandatory OEM/ fleet

  4. Vehicle to vehicle communications for trucks.

    Science.gov (United States)

    2014-01-01

    The trucking industry is a critical component of American commerce. The American : Trucking Association estimates that over 80 percent of U.S. communities depend : exclusively on trucking for delivery of their goods and commodities

  5. Fill That Truck | Poster

    Science.gov (United States)

    Feds Feed Families is a federal workforce initiative to fight hunger in our local communities. This year’s campaign began on June 13 and will continue until the end of August. After collecting approximately 550 pounds of food each of the last two years, NCI at Frederick is making a push to collect even more this summer. On June 29, during Take Your Child to Work Day, a 10-foot truck will be parked in the hub area along Chandler Street and Wood Street.

  6. Could Expanded Freight Rail Reduce Air Pollution from Trucks?

    Science.gov (United States)

    Bickford, E. E.; Holloway, T.; Johnston, M.

    2010-12-01

    Cars, trucks and trains are a significant source of emissions that impact both climate and air quality on regional to global scales. Diesel vehicles, most used for freight transport, account for 42% of on-road nitrogen oxide emissions, 58% of on-road fine particulate emissions, and 21% of on-road carbon dioxide emissions. With freight tonnage projected to increase 28% by 2018, and freight trucks the fastest growing source of transportation emissions, we evaluate the potential for increased rail capacity to reduce the environmental impacts of trucks. Most widely available mobile source emissions inventories contain insufficient spatial detail to quantify realistic emission scenario options, and none to date have been linked with commodity flow information in a manner appropriate to consider the true potential of rail substitution. To support a truck-to-rail analysis, and other policy assessments requiring roadway-by-roadway analysis, we have developed a freight emissions inventory for the Upper Midwest based on the Federal Highway Administration’s Freight Analysis Framework version 2.2 and the Environmental Protection Agency’s on-road emissions model, Mobile6.2. Using a Geographical Information System (GIS), we developed emissions scenarios for truck-to-rail modal shifts where 95% of freight tonnage on trips longer than 400 miles is shifted off of trucks and onto railways. Scenarios will be analyzed with the Community Multiscale Air Quality (CMAQ) regional model to assess air quality impacts of associated changes. By using well-respected transportation data and realistic assumptions, results from this study have the potential to inform decisions on transportation sustainability, carbon management, public health, and air quality.

  7. Analysis of truck platoon dynamics

    NARCIS (Netherlands)

    Verhoeff, L.; Zuurbier, J.; Lupker, H.A.

    1999-01-01

    This paper presents the analysis of truck platoon dynamics using a simulation environment. In this case the platoon consists of a number of trucks following each other using driver algorithms. MADYMO (a multibody and FE software package) and MATLAB/SIMULINK are coupled to allow for these driver

  8. Mitigating Wind Induced Truck Crashes

    Science.gov (United States)

    2009-12-25

    Dangerous weather and high wind in particular, is a common contributing factor in truck crashes. High wind speeds have been documented as a perennial cause of truck crashes in Kansas and other Great Plains states. The possibility of reducing such cra...

  9. Dump Truck Stability During Unloading

    Directory of Open Access Journals (Sweden)

    Yu. N. Baryshnikov

    2015-01-01

    Full Text Available The article deals with the problem of stability of the truck while unloading. The main symptom is a loss of stability of a vehicle rollover. The most common vehicle rollover occurs when unloading on sloped sites. The unloading area can be both longitudinal and cross slope. In this regard, the main task of the calculation is to determine the stability of the car the maximum allowable angle of discharge site and loads acting on the bearing system of the car.The paper presents a developed mathematical model of the truck when unloading on the longitudinal slope. It also offers the procedure of the step change in the parameters for the calculation of the critical angle of the site. The formulas for calculating the force interaction platform and the support system in the truck unloading at the site with a longitudinal slope are given. On the basis of the developed technique, a program for calculating longitudinal stability and loads acting on the bearing system dump trucks is created.Modern methods to assess stability while unloading the truck on a cross slope are analyzed. It is noted that the solution of this problem is developing in two directions. The first approach involves the testing truck samples on the special stands. Examples of bench tests on the stability of trucks are given. Another approach uses computational methods for the study. However, this requires the creation of a complex mathematical model of the truck, which should take into account the structural features of the suspension, the nonlinear elastic suspension components and tires, as well as the possibility of plastic deformation of the support system in torsion. In this formulation, the problem can only be solved using numerical methods and may be the subject of further research.The proposed approach allows multiple calculations for truck strength and stability already at an early designing stage in order to find the optimal design solution.

  10. Waste Management's LNG Truck Fleet

    International Nuclear Information System (INIS)

    Battelle

    1999-01-01

    The Alternative Motor Fuel Act of 1988 requires the U.S. Department of Energy to demonstrate and evaluate alternative fuels usage in the United States. DOE's National Renewable Energy Laboratory is conducting the Alternative Fuel Truck Evaluation Project to compare alternative fuel and diesel fuel trucks. Information for the comparison comes from data collected on the operational, maintenance, performance, and emissions characteristics of alternative fuel trucks being used in vehicle fleets and comparable diesel fuel trucks servings as controls within the same fleets. This report highlights the start-up experience and presents the lessons learned from a project that operated a fleet of liquefied natural gas (LNG) refuse haulers in Washington, Pennsylvania

  11. Potential Safety Benefit of the Blind Spot Detection System for Large Trucks on the Vulnerable Road Users in Taiwan

    Directory of Open Access Journals (Sweden)

    Wang Ming-Hang

    2016-01-01

    Full Text Available Considering motorcyclists, pedestrians and bicyclists as vulnerable road users (VRUs, more than 75 percent of the victims of fatal crashes involving large trucks in Taiwan are VRUs. Most crashes occurred at or were due to the blind spots of large trucks because of the size and traveling locations of the VRUs. This study applies typology and statistical methods to estimate the potential safety benefit of blind spot detection (BSD systems for large trucks on VRUs. The pre-crash scenarios associated with the blind spots of large trucks were derived by counting the maneuvers of large trucks and VRUs, prior to crashes, the truck drivers’ improper behaviors (cause of crashes, and the crash types. The number of crashes and fatalities were counted for the pre-crash scenario relevant to the BSD systems. A value of 0.8 of human machine interface factor (HMIF based on a previous study was applied to estimate the potential safety benefits of the BSD system. The results show that the implementation of BSD systems on all large trucks could help avoid about 24, 10, and 11 percent of large truck-involved crashes with pedestrians, bicycles, and motorcycles, respectively. The BSD systems could also save 5 pedestrians, 3 bicyclists, and 15 motorcyclists per year from crashes involving large trucks.

  12. Commercial truck parking and other safety issues.

    Science.gov (United States)

    2015-10-01

    Commercial truck parking is a safety issue, since trucks are involved in approximately 10% of all fatal accidents on interstates and : parkways in Kentucky. Drivers experience schedule demands and long hours on the road, yet they cannot easily determ...

  13. Papers on vehicle size : cars and trucks

    Science.gov (United States)

    1988-06-01

    The four papers in this volume describe analyses of car size : trends and truck occupant injuries and fatalities. All four were : written between June 1985 and December 1987. The topics : addressed include where heavy truck accidents occur, injury an...

  14. Norcal Prototype LNG Truck Fleet: Final Results

    Energy Technology Data Exchange (ETDEWEB)

    2004-07-01

    U.S. DOE and National Renewable Energy Laboratory evaluated Norcal Waste Systems liquefied natural gas (LNG) waste transfer trucks. Trucks had prototype Cummins Westport ISXG engines. Report gives final evaluation results.

  15. Large truck and bus crash facts, 2010.

    Science.gov (United States)

    2012-09-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2010. Selected crash statistics on passenger : vehicles are also presen...

  16. Large truck and bus crash facts, 2012.

    Science.gov (United States)

    2014-06-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2012. Selected crash statistics on passenger vehicles are also presented ...

  17. Large truck and bus crash facts, 2013.

    Science.gov (United States)

    2015-04-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and property damage only crashes involving large trucks and buses in 2013. Selected crash statistics on passenger vehicles are also presented ...

  18. Large truck and bus crash facts, 2009.

    Science.gov (United States)

    2011-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2009. Selected crash statistics on passenger : vehicles are also presen...

  19. Large truck and bus crash facts, 2011.

    Science.gov (United States)

    2013-10-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2011. Selected crash statistics on passenger : vehicles are also presen...

  20. Naturalistic Study of Truck Following Behavior

    Science.gov (United States)

    2016-04-01

    Volpe conducted the Naturalistic study of truck following behavior to gain a better understanding of how trucks follow other vehicles in the real world, with the ultimate goal of supporting the Federal Highway Administration in the development of aut...

  1. Aerodynamics Research Revolutionizes Truck Design

    Science.gov (United States)

    2008-01-01

    During the 1970s and 1980s, researchers at Dryden Flight Research Center conducted numerous tests to refine the shape of trucks to reduce aerodynamic drag and improved efficiency. During the 1980s and 1990s, a team based at Langley Research Center explored controlling drag and the flow of air around a moving body. Aeroserve Technologies Ltd., of Ottawa, Canada, with its subsidiary, Airtab LLC, in Loveland, Colorado, applied the research from Dryden and Langley to the development of the Airtab vortex generator. Airtabs create two counter-rotating vortices to reduce wind resistance and aerodynamic drag of trucks, trailers, recreational vehicles, and many other vehicles.

  2. On the Equivalence of Tank Trucks and General Purpose Trucks ...

    African Journals Online (AJOL)

    African Journal for the Psychological Study of Social Issues ... Trucking is a business that benefits from segmentation, which is the subdividing of the overall market into homogeneous subsets of customers where any subset(s) may be selected as a target market to be reached with a distinct marketing mix. But the fact that ...

  3. Improvement of underrun protection of trucks

    NARCIS (Netherlands)

    Coo, P.J.A. de; Blaauw, G.J.

    1999-01-01

    Truck accidents represent a significant factor in the overall road accident scene, namely 25 to 30% of the fatal accidents in the EU. Collision partners of trucks are mainly passenger cars in car-to-truck frontal collisions. The severity of this kind of accidents is due to the incompatibility of

  4. Structural challenges in the development of a truck shipping cask for the OCRWM cask systems development program

    International Nuclear Information System (INIS)

    Mello, R.M.; Severson, W.J.; Nair, B.R.

    1990-01-01

    The development of a spent fuel transportation cask design based on a structural material without licensing precedent presents many challenges. The U.S. Nuclear Regulatory Commission (NRC) requires that any new material be qualified to meet the design and fabrication requirements of the ASME Boiler and Pressure Vessel Code, Section III, Class 1. This paper discusses the strategy that is being implemented towards obtaining Code Acceptance of a titanium alloy (3A1-2.5V). This alloy has been chosen as the principal structural material for a Legal Weight Truck cask being developed by Westinghouse for the U.S. Department of Energy. The analysis approach used on some of the principal cask components is also presented

  5. Computer simulations of a generic truck cask in a regulatory fire using the Container Analysis Fire Environment (CAFE) code

    International Nuclear Information System (INIS)

    Ju, H.; Greiner, M.; Suo-Anttila, A.

    2002-01-01

    The Container Analysis Fire Environment (CAFE) computer code is designed to predict accurately convection and radiation heat transfer to a thermally massive object engulfed in a large pool fire. It is well suited for design and risk analyses of spent nuclear fuel transport systems. CAFE employs computational fluid dynamics and several fire and radiation models. These models must be benchmarked using experimental results. In this paper, a set of wind velocity conditions are determined which allow CAFE accurately to reproduce recent heat transfer measurements for a thick walled calorimeter in a ST-1 regulatory pool fire. CAFE is then used to predict the response of an intack (thin walled) generic legal weight truck cask. The maximum temperatures reached by internal components are within safe limits. A simple 800 deg. C, grey-radiation fire model gives maximum component temperatures that are somewhat below those predicted by CAFE. (author)

  6. A tough truck for ATLAS

    CERN Multimedia

    2003-01-01

    One of the mobile support structures that will be used to manoeuvre and assemble components of the ATLAS detector in its cavern was put through its paces at the end of July and passed its load tests with flying colours. The tests, which involved the surveyors taking measurements to detect any load-induced mechanical deformations, were carried out in Building 191. "The "truck" has been subjected to static tests with loads of up to 1250 tonnes and can carry and transport on air cushions a nominal load of up to 1000 tonnes at a top speed of 30 cm per minute," explains project leader Tommi Nyman. "It took two weeks to assemble the truck's components, the last of which arrived at CERN on 24 June. It then took a further 20 days to load the truck up for the test." The 8.5 metre-high truck will be used for final assembly of some of the ATLAS components, including the calorimeters, in cavern UX15. This powerful device is the result of a collaboration between CERN and the Henryk Niewodniczanski Institute of Nuclear ...

  7. Weather delay costs to trucking.

    Science.gov (United States)

    2012-11-01

    Estimates of the nations freight sector of transportation range to upwards of $600 billion of total gross domestic product with 70 percent of total value and 60 percent of total weight moving by truck. Weather-related delays can add significantly ...

  8. Truck Thermoacoustic Generator and Chiller

    Energy Technology Data Exchange (ETDEWEB)

    Keolian, Robert

    2011-03-31

    This Final Report describes the accomplishments of the US Department of Energy (DOE) cooperative agreement project DE-FC26-04NT42113 - Truck Thermoacoustic Generator and Chiller - whose goal is to design, fabricate and test a thermoacoustic piezoelectric generator and chiller system for use on over-the-road heavy-duty-diesel trucks, driven alternatively by the waste heat of the main diesel engine exhaust or by a burner integrated into the thermoacoustic system. The thermoacoustic system would utilize engine exhaust waste heat to generate electricity and cab air conditioning, and would also function as an auxiliary power unit (APU) for idle reduction. The unit was to be tested in Volvo engine performance and endurance test cells and then integrated onto a Class 8 over-the-road heavy-duty-diesel truck for further testing on the road. The project has been a collaboration of The Pennsylvania State University Applied Research Laboratory, Los Alamos National Laboratory, Clean Power Resources Inc., and Volvo Powertrain (Mack Trucks Inc.). Cost share funding was provided by Applied Research Laboratory, and by Clean Power Resources Inc via its grant from Innovation Works - funding that was derived from the Commonwealth of Pennsylvania. Los Alamos received its funding separately through DOE Field Work Proposal 04EE09.

  9. Truck transportation of radioactive materials

    International Nuclear Information System (INIS)

    Madsen, M.M.; Wilmot, E.L.

    1983-01-01

    Analytical models in RADTRAN II are used to calculate risks to population subgroups such as people along transport routes, people at stops, and crewman. The stops model, which calculates the dose to persons adjacent to the transport vehicle while it is stopped, frequently provides the largest contribution to incident-free radiological impacts. Components such as distances from the vehicle containing radioactive material to nearby people at stops, stop duration, and number of crew members are required for the stops model as well as other incident-free models. To provide supporting data for RADTRAN II based on operational experience, selected truck shipments of radioactive material were observed from origin to destination. Other important aspects of this program were to correlate package size to effective shipment transport index (TI) using radiological surveys and to characterize population distributions and proximities of people to the shipment at a generic truck stop

  10. [Pedestrian dragged under a truck].

    Science.gov (United States)

    Zaba, Czesław; Lewandowski, Andrzej; Kołowski, Janusz; Tezyk, Artur

    2011-01-01

    A traffic accident is described, involving a pedestrian who was at first hit and subsequently hooked up by his clothing by a suspension element of a low-floor truck trailer and dragged along a road for the distance of 3500 m. Autopsy demonstrated that the pedestrian died of cerebro-cranial injuries, inflicted while he had been hit by the truck. Additionally, the frontal surface of his body demonstrated external injuries typical for dragging of the body along the roadway. Before being dragged, the pedestrian was hit by the front of the vehicle, when he was in a sitting position, or was rising or else was in a recumbent position with an elevated head and trunk. Traffic accidents of the type were seldom described in the national and foreign literature.

  11. Solar hydrogen for urban trucks

    Energy Technology Data Exchange (ETDEWEB)

    Provenzano, J.: Scott, P.B.; Zweig, R. [Clean Air Now, Northridge, CA (United States)

    1997-12-31

    The Clean Air Now (CAN) Solar Hydrogen Project, located at Xerox Corp., El Segundo, California, includes solar photovoltaic powered hydrogen generation, compression, storage and end use. Three modified Ford Ranger trucks use the hydrogen fuel. The stand-alone electrolyzer and hydrogen dispensing system are solely powered by a photovoltaic array. A variable frequency DC-AC converter steps up the voltage to drive the 15 horsepower compressor motor. On site storage is available for up to 14,000 standard cubic feet (SCF) of solar hydrogen, and up to 80,000 SCF of commercial hydrogen. The project is 3 miles from Los Angeles International airport. The engine conversions are bored to 2.9 liter displacement and are supercharged. Performance is similar to that of the Ranger gasoline powered truck. Fuel is stored in carbon composite tanks (just behind the driver`s cab) at pressures up to 3600 psi. Truck range is 144 miles, given 3600 psi of hydrogen. The engine operates in lean burn mode, with nil CO and HC emissions. NO{sub x} emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two trucks have been converted for the Xerox fleet, and one for the City of West Hollywood. A public outreach program, done in conjunction with the local public schools and the Department of Energy, introduces the local public to the advantages of hydrogen fuel technologies. The Clean Air Now program demonstrates that hydrogen powered fleet development is an appropriate, safe, and effective strategy for improvement of urban air quality, energy security and avoidance of global warming impact. Continued technology development and cost reduction promises to make such implementation market competitive.

  12. Determinants of fuel consumption in mining trucks

    International Nuclear Information System (INIS)

    Dindarloo, Saeid R.; Siami-Irdemoosa, Elnaz

    2016-01-01

    Analysis of fuel consumption in a large surface mine, during more than 5000 cycles of material transportation, revealed considerable variability in the data. Truck fuel estimation based on the mining truck manufacturers' manuals/estimates is not capable of capturing this variability in the fuel consumption data. Partial least squares regression and autoregressive integrated moving average methods were employed to examine the effect of cyclic activities on fuel consumption, and to recommend relevant remedies for consumption reduction. Proper modifications of the operation can result in improved cycle times. Consequently, minimizing some cyclic activities would enhance energy efficiency. The truck “empty idle time” was a major contributor to unnecessary fuel consumption. Since the truck queues at shovels are a major component of the “empty idle time”, decisions should be reviewed to reduce the truck queues at loading points. Improved dispatching strategies, optimal muck pile shape and size distribution, and improved shovel/loader operator skills are effective preventive measures to minimize truck flow bottlenecks at loading points, and thus to improve energy efficiency at mines. - Highlights: • A large fleet of mining trucks consumes considerable amounts of energy. • Current energy models do not consider the effect of site-specific mining conditions. • A new methodology based on material handling cyclic activities is proposed. • Fuel consumption rates in different truck operating modes are determined. • The new model is compared with the truck manufacturer's energy consumption guideline.

  13. Developing a GPS-based truck freight performance measure platform.

    Science.gov (United States)

    2010-05-01

    Although trucks move the largest volume and value of goods in urban areas, relatively little is known about their travel : patterns and how the roadway network performs for trucks. Global positioning systems (GPS) used by trucking : companies to mana...

  14. Development of test scenarios for off-roadway crash countermeasures based on crash statistics

    Science.gov (United States)

    2002-09-01

    This report presents the results from an analysis of off-roadway crashes and proposes a set of crash-imminent scenarios to objectively test countermeasure systems for light vehicles (passenger cars, sport utility vehicles, vans, and pickup trucks) ba...

  15. Heavy truck rollover characterization (phase B).

    Science.gov (United States)

    2009-09-01

    The Heavy Truck Rollover Characterization Study - Phase-B builds on the results of prior phases of research. Phases 1 and 2 (Funded by Federal Highway Administration) involved heavy truck rollover characterization for a tractor and box-trailer; and P...

  16. Trusted Truck(R) II (phase A).

    Science.gov (United States)

    2009-01-01

    The Trusted Truck Program was initiated in 2003 as a joint effort by NTRCI, Volvo and UT. The vision of the Trusted Truck program is to develop a secure and "trusted" transport solution from pickup to delivery. The program's objective is to incre...

  17. Speed docking: reducing truck turn times

    NARCIS (Netherlands)

    Ploos van Amstel, W.

    2013-01-01

    Truck turn times in FMCG supply chain are unreliable. The Dutch ‘Speed Docking’ project in gave clear evidence to this. The result is too many trucks and drivers. FMCG producers, together with logistics service providers and customers, can realise improvements with the use of mobile communication,

  18. Scenario planning.

    Science.gov (United States)

    Enzmann, Dieter R; Beauchamp, Norman J; Norbash, Alexander

    2011-03-01

    In facing future developments in health care, scenario planning offers a complementary approach to traditional strategic planning. Whereas traditional strategic planning typically consists of predicting the future at a single point on a chosen time horizon and mapping the preferred plans to address such a future, scenario planning creates stories about multiple likely potential futures on a given time horizon and maps the preferred plans to address the multiple described potential futures. Each scenario is purposefully different and specifically not a consensus worst-case, average, or best-case forecast; nor is scenario planning a process in probabilistic prediction. Scenario planning focuses on high-impact, uncertain driving forces that in the authors' example affect the field of radiology. Uncertainty is the key concept as these forces are mapped onto axes of uncertainty, the poles of which have opposed effects on radiology. One chosen axis was "market focus," with poles of centralized health care (government control) vs a decentralized private market. Another axis was "radiology's business model," with one pole being a unified, single specialty vs a splintered, disaggregated subspecialty. The third axis was "technology and science," with one pole representing technology enabling to radiology vs technology threatening to radiology. Selected poles of these axes were then combined to create 3 scenarios. One scenario, termed "entrepreneurialism," consisted of a decentralized private market, a disaggregated business model, and threatening technology and science. A second scenario, termed "socialized medicine," had a centralized market focus, a unified specialty business model, and enabling technology and science. A third scenario, termed "freefall," had a centralized market focus, a disaggregated business model, and threatening technology and science. These scenarios provide a range of futures that ultimately allow the identification of defined "signposts" that can

  19. Fuel Cell Powered Lift Truck

    Energy Technology Data Exchange (ETDEWEB)

    Moulden, Steve [Sysco Food Service, Houston, TX (United States)

    2015-08-20

    This project, entitled “Recovery Act: Fuel Cell-Powered Lift Truck Sysco (Houston) Fleet Deployment”, was in response to DOE funding opportunity announcement DE-PS36-08GO98009, Topic 7B, which promotes the deployment of fuel cell powered material handling equipment in large, multi-shift distribution centers. This project promoted large-volume commercialdeployments and helped to create a market pull for material handling equipment (MHE) powered fuel cell systems. Specific outcomes and benefits involved the proliferation of fuel cell systems in 5-to 20-kW lift trucks at a high-profile, real-world site that demonstrated the benefits of fuel cell technology and served as a focal point for other nascent customers. The project allowed for the creation of expertise in providing service and support for MHE fuel cell powered systems, growth of existing product manufacturing expertise, and promoted existing fuel cell system and component companies. The project also stimulated other MHE fleet conversions helping to speed the adoption of fuel cell systems and hydrogen fueling technology. This document also contains the lessons learned during the project in order to communicate the successes and difficulties experienced, which could potentially assist others planning similar projects.

  20. Scenario? Guilty!

    DEFF Research Database (Denmark)

    Kyng, Morten

    1992-01-01

    Robert Campbell categorizes the word "scenario" as a buzzword, identifies four major uses within HCI and suggests that we adopt new terms differentiating these four uses of the word. My first reaction to reading the article was definitely positive, but rereading it gave me enough second thoughts...... to warrant a response. I should probably confess that I searched my latest paper for the word "scenario" and found eight occurrences, none of which fell in the categories described by Campbell....

  1. Disruption management for truck appointment system at a container terminal

    DEFF Research Database (Denmark)

    Li, Na; Chen, Gang; Govindan, Kannan

    2018-01-01

    Disruption often occurs in both land-side and sea-side operations at a container terminal, causing substantial interference of scheduled operations and poor green performance. The land-side disruption is rarely researched, and this paper addresses the ordinary level of such disruption where......-appointed arrivals at a container terminal that is running an appointment system. Second, we propose some response strategies to cope with different levels of disruptions, and evaluate their resilience ability with two Key Performance Indicators (KPIs): total waiting time of on-time trucks and total idling emissions...... scenarios is a combined one based on priority and yard-crane moving distance; its performance depends primarily on the concentration level of container locations and secondly on the system utilization. In the other scenarios that have low arrival punctuality, the best strategy could focus purely on yard...

  2. 19 CFR 123.41 - Truck shipments transiting Canada.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Truck shipments transiting Canada. 123.41 Section... OF THE TREASURY CUSTOMS RELATIONS WITH CANADA AND MEXICO United States and Canada In-Transit Truck Procedures § 123.41 Truck shipments transiting Canada. (a) Manifest required. Trucks with merchandise...

  3. Current scenario

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Current scenario. India , like other parts of the world, is also facing the problem of increase in the incidence of drug resistance in tuberculosis. Multi-drug resistance (MDR, resistance to RIF & INH) and extensively drug resistant strains (X-DR, resistance to RIF, INH, FQs ...

  4. Acceleration lane design for higher truck volumes.

    Science.gov (United States)

    2008-12-09

    The research project examined attributes associated with tractor-trailer trucks accelerating on freeway entry ramps and : entering the main traffic lanes. Data for this project were collected at five commercial vehicle weigh stations in : Arkansas an...

  5. Light Duty Truck Weight Reduction Evaluation

    Science.gov (United States)

    1980-10-01

    The objectives of this program were to identify the weight reduction potential of pickup trucks, vans, and utility vehicles less than or equal to 8500 lb. gross vehicle weight through design modification, redesign, and material substitution; and more...

  6. Higher speed freight truck design : performance requirements.

    Science.gov (United States)

    2013-10-01

    This proposed requirements document combines a set of requirements for high-speed freight car truck design and performance : from the generally accepted standards in the U.S. Code of Federal Regulation (CFR), the Association of American Railroads : (...

  7. Higher speed freight truck : structural analysis.

    Science.gov (United States)

    2013-10-01

    Sharma & Associates, Inc. (SA) had previously (20052009) developed a higher speed freight truck under sponsorship ofthe : Federal Railroad Administration (FRA). Under the current contract, SA wastasked with developing performance requirements : fo...

  8. Higher speed freight truck : vehicle dynamics analysis.

    Science.gov (United States)

    2015-08-01

    Previously, Sharma & Associates, Inc. (SA) developed a higher speed freight truck design under sponsorship of the Federal : Railroad Administration. Under the current contract, SA was tasked with developing performance requirements for higher speed :...

  9. Acceptance test procedure for core sample trucks

    International Nuclear Information System (INIS)

    Smalley, J.L.

    1995-01-01

    The purpose of this Acceptance Test Procedure is to provide instruction and documentation for acceptance testing of the rotary mode core sample trucks, HO-68K-4600 and HO-68K-4647. The rotary mode core sample trucks were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Acceptance testing of the rotary mode core sample trucks will verify that the design requirements have been met. All testing will be non-radioactive and stand-in materials shall be used to simulate waste tank conditions. Compressed air will be substituted for nitrogen during the majority of testing, with nitrogen being used only for flow characterization

  10. Delay and environmental costs of truck crashes

    Science.gov (United States)

    2013-03-01

    This report presents estimates of certain categories of costs of truck- and bus-involved crashes. Crash related costs estimated as part of this study include vehicle delay costs, emission costs, and fuel consumption costs. In addition, this report al...

  11. Fuel Cell Hydroge Manifold for Lift Trucks

    DEFF Research Database (Denmark)

    Hosseinzadeh, Elham

    a virtual forklift system. This investigation examines important performance metrics such as hydrogen consumption and battery SOC as a function of fuel cell and battery size, control strategy, drive cycle, and load variation for a forklift truck system. This study can be used as a benchmark for choosing......Reducing CO2 emissions are getting more attention because of global warming. The transport sector which is responsible for a significant amount of emissions is going to reduce them due to new and upcoming regulations. Using fuel cells may be one way to help to reduce the emissions from this sector....... Battery driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need long time to recharge and may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...

  12. Diesel Engine Light Truck Application

    Energy Technology Data Exchange (ETDEWEB)

    None

    2007-12-31

    The Diesel Engine Light Truck Application (DELTA) program consists of two major contracts with the Department of Energy (DOE). The first one under DE-FC05-97-OR22606, starting from 1997, was completed in 2001, and consequently, a final report was submitted to DOE in 2003. The second part of the contract was under DE-FC05-02OR22909, covering the program progress from 2002 to 2007. This report is the final report of the second part of the program under contract DE-FC05-02OR22909. During the course of this contract, the program work scope and objectives were significantly changed. From 2002 to 2004, the DELTA program continued working on light-duty engine development with the 4.0L V6 DELTA engine, following the accomplishments made from the first part of the program under DE-FC05-97-OR22606. The program work scope in 2005-2007 was changed to the Diesel Particulate Filter (DPF) soot layer characterization and substrate material assessment. This final report will cover two major technical tasks. (1) Continuation of the DELTA engine development to demonstrate production-viable diesel engine technologies and to demonstrate emissions compliance with significant fuel economy advantages, covering progress made from 2002 to 2004. (2) DPF soot layer characterization and substrate material assessment from 2005-2007.

  13. Scrotal neoplasia: would truck drivers be at greater risk?

    Directory of Open Access Journals (Sweden)

    Daniel Seabra

    2007-08-01

    Full Text Available OBJECTIVE: To analyze how scrotal neoplasias have been managed during the past decade and to question possible factors or professions associated to its presence. MATERIALS AND METHODS: We retrospectively evaluated every case reported from 1995 to 2005 at our hospital. We described the clinical scenario, complementary exams, treatments and outcomes. We also tried to verify if there was any risk, predisposing factors or professions that would explain the cancer origin. RESULTS: Six cases were reviewed. Out of these, three patients were truck drivers. Five of them showed restricted lesions without inguinal lymph nodes enlargement. Histologically, six patients presented squamous carcinoma, with two of them having the verrucous type. The median age of patients was 52 years old (31 to 89. The five patients who are still alive had their lesions completely removed with safety margin and primary closure. CONCLUSIONS: We have noticed that the scrotal carcinoma behavior is similar to that of the penis, where removal of the lesion and study of the regional lymph nodes help to increase the patient survival rate. The outstanding fact was that three out of six patients were truck drivers, raising the hypothesis that such profession, maybe due to the contact or attrition with the diesel exhaust expelled by the engine or to sexual promiscuity, would imply in a larger risk of developing this rare neoplasia.

  14. 49 CFR 238.419 - Truck-to-car-body and truck component attachment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Truck-to-car-body and truck component attachment. 238.419 Section 238.419 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER EQUIPMENT SAFETY STANDARDS Specific Requirements for Tier II Passenger Equipment ...

  15. A synthetic approach to compare the large truck crash causation study and naturalistic driving data.

    Science.gov (United States)

    Hickman, Jeffrey S; Hanowski, Richard J; Bocanegra, Joseph

    2018-03-01

    Truck crashes represent a significant problem on our nation's highways. There is a great opportunity to learn about crash causation by analyzing and comparing the Large Truck Crash Causation Study (LTCCS) and naturalistic driving (ND) data. These data sets provide in-depth information, but have contrasting strengths and weaknesses. The LTCCS contains information on high-severity crashes (crashes and fatal crashes), but relied on data collected during crash investigations. The LTCCS identified principal driver errors in the crash, such as the Critical Reason, but not detailed behaviors or scenario sequences. The ND data sets relate primarily to non-crashes that are detectable from dynamic vehicle events, such as hard braking, swerve, etc., provide direct video observations of the driver and the surrounding driving scene and precise information on driver inputs (kinematics) and captured events, and provide certain types of exposure data that cannot easily be obtained using crash reconstruction data. The ND data are collected continuously, thereby capturing both safety-critical events and normative driving (i.e., baseline). The current project evaluated large-truck crash data from the LTCCS and two large-truck ND data sets, the Naturalistic Truck Driving Study and the Drowsy Driver Warning System Field Operational Test. A synthetic risk ratio analysis on the associated factor, Following Too Closely, indicated that truck drivers in the LTCCS were 1.34 times more likely to be involved in a crash, than an ND crash-relevant conflict, if they were following too closely (i.e., tailgating). Given several caveats noted in the paper, this study suggests it's possible to use the ND data set to calculate the exposure of a given behavior and use the LTCCS data set to calculate the crash exposure to the same behavior. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. HIV testing preferences among long distance truck drivers in Kenya: a discrete choice experiment.

    Science.gov (United States)

    Strauss, Michael; George, Gavin; Lansdell, Emma; Mantell, Joanne E; Govender, Kaymarlin; Romo, Matthew; Odhiambo, Jacob; Mwai, Eva; Nyaga, Eston N; Kelvin, Elizabeth A

    2018-01-01

    Providing HIV testing services to truck drivers in Africa is crucial but has proven challenging. The introduction of HIV self-testing promises to provide expanded service delivery options for clients, potentially increasing demand for services and expanding coverage - especially important for high-risk and difficult-to-reach populations. This study examines the preferences regarding HIV testing service delivery models, among long distance truck drivers to identify testing services that would appeal to this population. Using a discrete choice experiment, this study examines the drivers of choice regarding HIV counselling and testing among 305 truck drivers recruited from two roadside wellness clinics along major trucking routes in Kenya. Participants made trade-offs between characteristics of HIV testing service delivery models by making hypothetical choices in a series of paired HIV testing scenarios. Conditional logit models were used to identify the HIV testing characteristics driving the selection of preferred scenarios, as well as determine whether preferences interact with individual characteristics - especially HIV testing history. Participants preferred free, provider-administered HIV testing at a roadside clinic, using a finger-prick test, with in-person counselling, undertaken in the shortest possible time. The strongest driver of choice was the cost of the test. Those who had never tested previously preferred oral testing and telephonic counselling, while those who were not regular testers favoured clinic based - over self-testing. The results of this study indicate that for the majority of participants - most of whom had tested before - the existing services offered at roadside clinics were the preferred service delivery model. The introduction of oral self-testing increases the options available to truck drivers and may even improve testing uptake for some, especially among those who have never tested before. However, these findings suggest the impact

  17. Development of crash imminent test scenarios for Integrated Vehicle-Based Safety Systems

    Science.gov (United States)

    2007-04-01

    This report identifies crash imminent test scenarios based on common pre-crash scenarios for integrated vehicle-based safety systems that alert the driver of a light vehicle or a heavy truck to an impending rear-end, lane change, or run-off-road cras...

  18. Impact of left lane truck restriction strategies on multilane highways in Louisiana : a literature review.

    Science.gov (United States)

    2009-04-01

    Truck lane restriction strategies (TLRS) are a means of managing truck traffic on highways by prohibiting trucks from using certain lanes to minimize interaction between trucks and other vehicles. The purpose of this study is to review the literature...

  19. Heavy Truck Clean Diesel Cooperative Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Milam, David

    2006-12-31

    This report is the final report for the Department of Energy on the Heavy Truck Engine Program (Contract No. DE-FC05-00OR22806) also known as Heavy Truck Clean Diesel (HTCD) Program. Originally, this was scoped to be a $38M project over 5 years, to be 50/50 co-funded by DOE and Caterpillar. The program started in June 2000. During the program the timeline was extended to a sixth year. The program completed in December 2006. The program goal was to develop and demonstrate the technologies required to enable compliance with the 2007 and 2010 (0.2g/bhph NOx, 0.01g/bhph PM) on-highway emission standards for Heavy Duty Trucks in the US with improvements in fuel efficiency compared to today's engines. Thermal efficiency improvement from a baseline of 43% to 50% was targeted.

  20. Large truck and bus crash facts, 2008. 

    Science.gov (United States)

    2010-03-01

    This annual edition of Large Truck and Bus Crash Facts contains descriptive statistics about fatal, injury, and : property damage only crashes involving large trucks and buses in 2008. Selected crash statistics on passenger : vehicles are also presen...

  1. Fuel Cell Hydroge Manifold for Lift Trucks

    OpenAIRE

    Hosseinzadeh, Elham; Rokni, Masoud; Elmegaard, Brian

    2012-01-01

    Reducing CO2 emissions are getting more attention because of global warming. The transport sector which is responsible for a significant amount of emissions is going to reduce them due to new and upcoming regulations. Using fuel cells may be one way to help to reduce the emissions from this sector. Battery driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need long time to recharge and may be out of work for a...

  2. Analysis of risk factors in severity of rural truck crashes.

    Science.gov (United States)

    2016-04-01

    Trucks are a vital part of the logistics system in North Dakota. Recent energy developments have : generated exponential growth in the demand for truck services. With increased density of trucks in the : traffic mix, it is reasonable to expect some i...

  3. Diesel and Truck Certification Needs Assessment: Two Surveys.

    Science.gov (United States)

    Broadbent, William A.

    Recommendations for the improvement of the diesel engine and truck components of the Hawaii state certification examination for automobile and truck mechanics were solicited from 14 major private businesses repairing heavy tractor rigs and/or diesel engines on Oahu and a statewide sample of 21 trucking firms and other companies making extensive…

  4. Reducing Truck Emissions at Container Terminals in a Low Carbon Economy: Proposal of a Queueing-based Bi-Objective Model for Optimizing Truck Arrival Pattern

    DEFF Research Database (Denmark)

    Chen, Gang; GOVINDAN, Kannan; Golias, Mihalis M.

    2012-01-01

    This study proposes a methodology to optimize truck arrival patterns to reduce emissions from idling truck engines at marine container terminals. A bi-objective model is developed minimizing both truck waiting times and truck arrival pattern change. The truck waiting time is estimated via...... a queueing network. Based on the waiting time, truck idling emissions are estimated. The proposed methodology is evaluated with a case study, where truck arrival rates vary over time. We propose a Genetic Algorithm based heuristic to solve the resulting problem. Result shows that, a small shift of truck...... arrivals can significantly reduce truck emissions, especially at the gate....

  5. Criticality safety and shielding design issues in the development of a high-capacity cask for truck transport

    International Nuclear Information System (INIS)

    Boshoven, J.K.

    1992-01-01

    General Atomics (GA) will be submitting an application for certification to the US Nuclear Regulatory Commission (NRC) for the GA-4 and GA-9 Casks In 1992. The GA-4 and GA-9 Casks are high-capacity legal weight truck casks designed to transport light water reactor spent fuel assemblies. To maintain a capacity of four pressurized-water-reactor (PWR) spent fuel assemblies, the GA-4 Cask uses burnup credit as part of the criticality control for initial enrichments over 3.0 wt% U-235. Using the US Department of Energy (DOE) Burnup Credit Program as a basis, GA has performed burnup credit analysis which is included in the Safety Analysis Report for Packaging (SARP). The GA-9 Cask can meet the criticality safety requirements using the ''fresh fuel'' assumption. Our approach to shielding design is to optimize the GA-4 and GA-9 Cask shielding configurations for minimum weights and maximum payloads. This optimization involves the use of the most effective shielding material, square cross-section geometry with rounded corners and tapered neutron shielding sections in the non-fuel regions

  6. 49 CFR 230.109 - Tender trucks.

    Science.gov (United States)

    2010-10-01

    ... five leaves in the entire spring pack broken; (2) A broken coil spring or saddle; (3) A coil spring... maximum clearance shall be 3/8 inch on each side for rear trucks and 3/4 inch on each side for front...

  7. INTRALOG, intelligent autonomous truck applications in Logistics

    NARCIS (Netherlands)

    MSc Berry Gerrits; Dr. Frans Tillema; MMC A.F. Spruijt; MSc Leo Buning

    2016-01-01

    INTRALOG is a project, to better use of materials, there by leading to improvements for People (better safety, lower physical work load), Planet (lower emissions and energy/ fuel con started September 2015, in which Automated Guided Truck Applications will be developed. Automated systems typically

  8. Case Study: Natural Gas Regional Transport Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Laughlin, M.; Burnham, A.

    2016-08-01

    Learn about Ryder System, Inc.'s experience in deploying nearly 200 CNG and LNG heavy-duty trucks and construction and operation of L/CNG stations using ARRA funds. Using natural gas in its fleet, Ryder mitigated the effects of volatile fuel pricing and reduced lifecycle GHGs by 20% and petroleum by 99%.

  9. Light Truck Characteristics, Historical Data Base

    Science.gov (United States)

    1980-11-01

    The report is a description of the data about the physical, operating performance, and market characteristics of light trucks for the model years 1955 through 1977, which is stored on tape in DOT/TSC DEC System 10 computer system. Vehicles are report...

  10. Light Duty Truck Characteristics, Historical Data Base

    Science.gov (United States)

    1979-12-01

    The report is a collection of data concerning physical, operating, performance, and market characteristics of light duty trucks for the model years 1972 and 1975 thru 1977. The data is stored on tape in DOT/TSC DEC System 10 computer system. Informat...

  11. COMPETITIVE PRESSURE SYSTEMS MAPPING IN THE BRAZILIAN TRUCK MARKET

    Directory of Open Access Journals (Sweden)

    Ricardo Costa da Cruz

    2013-06-01

    Full Text Available The automotive business in Brazil achieved 10% of the industry revenue and 6% of the formal employment by 2008. The commercial vehicle segment concentrated so far eight truck makers that experienced their best market figures in 2008, the economy crisis in 2009, and an extraordinary recovery in 2010. Government tax reduction programs as well as special financing incentives were undoubtedly decisive to re-stimulate the business during the crisis. Positive Brazilian perspectives with the boom in the agricultural, oil and gas, mining and infrastructure activities plus the coming sports events call the attention of new players that are quickly implementing different business strategies to become part of the game. New emission regulations starting from 2012 also bring uncertainties, challenges and opportunities. With the growing globalization and market concentration it's critical for any industry understand and minimize the forces of competitive pressures. The main goal of this paper, therefore, is to contribute to the academy with an alternative approach of strategic and behavioral analysis of rivalry and competition different than the five forces model of Porter. Ford, Iveco, MAN, Mercedes-Benz, Scania and Volvo were assessed from 2008 to 2010 within three main performance indicators – unit sales, gross revenues and operating profits – supporting the elaboration of the competitive pressure systems mapping model of D'aveni, including a hypothetical future scenario with a new entrant and the potential impacts in the system. Main findings and results portray the asymmetrical strategic behavior of competitors and the temporary dynamic stability in the Brazilian truck industry.

  12. Holonic fleet scheduling with TeleTruck

    Science.gov (United States)

    Bürckert, Hans-Jürgen; Fischer, Klaus; Vierke, Gero

    1999-03-01

    In this paper we describe the TeleTruck approach for multi-agent fleet scheduling. In close collaboration with a forwarding company we developed a multiagent system with holonic agents that will support dispatch officers in transport scheduling. The system is capable of handling real-world requirements like dynamics and uncertainty. Holonic agents are agents which are composed of sub-agents acting in a corporate way. We give a brief overview of the current state of the TeleTruck application prototype. We discuss requirements of communication, coordination, and resource control that distinguish holonic from common multiagent systems and we show, how we integrated these concepts with the three-layered agent architecture INTERRAP, in order to result in a smooth implementation of a dispatch support system.

  13. DETERMINATION OF THE LOADS POSITION ON TRUCKS

    Directory of Open Access Journals (Sweden)

    César A. Chagoyén-Méndez

    2015-07-01

    Full Text Available In this paper, we presented the main problems that entail an inadequate distribution of loads on trucks and we described in detail a methodology for determining the proper position, which concludes with the completion of the installation diagrams. The methodology was obtained from the solution of the particular case of a tank of liquefied petroleum gas (LPG of 14'000 liter on a DAF CF 75.310 truck. Another result of this work is a software which allows to determine the exact position it should be the gravity center of the load relative to the front axle and the reactions on each axis, with the possibility of evaluating different variants.

  14. Dump truck-related deaths in construction, 1992-2007.

    Science.gov (United States)

    McCann, Michael; Cheng, Mei-Tai

    2012-05-01

    Dump trucks are universally used in construction and other industries to haul materials to the location and to remove waste materials. The source for dump truck-related fatality data was the Bureau of Labor Statistics Census of Fatal Occupational Injuries (CFOI) Research File. From 1992 to 2007, 829 construction workers were killed in dump truck-related incidents nationwide. Of those, 336 were dump truck operators with 215 deaths occurring in street and highway incidents. Another 343 deaths involved workers on foot, three-quarters struck by dump trucks. Sixty-four of the construction workers killed were maintaining dump trucks, 22 when caught between the truck frame and a falling dump truck bed. Of the 86 other deaths, 55 involved streets and highways. Recommendations include: (i) improving the reporting of seat belt usage in fatality reports; (ii) requiring use of seat belts; (iii) requiring the use of backup alarms, spotters, or other methods to alert dump truck operators to workers in their blind spots; (iv) prohibiting direct dumping at river banks and embankments; (v) using cameras or radar to enforce stopping at railway crossings; and (xi) enforcing worker safety practices (e.g., lockout/tagout procedures on elevated dump truck beds). Copyright © 2011 Wiley Periodicals, Inc.

  15. Prospects of development of land driverless trucks

    Science.gov (United States)

    Bakhmutov, S.; Saykin, A.; Endachev, D.; Evgrafov, V.; Shagurin, A.; Kulikov, I.; Fedoseev, K.

    2018-02-01

    The paper is dedicated to the problem of creation and efficient use of driverless trucks. It also contains general analysis of foreign experience and development trends. The concept of FSUE “NAMI” for development of a platoon of driverless trucks for cargo transportation between specialized terminals on public roads is provided. A road train with virtual couplings where the lead vehicle has a driver and the rest are driverless is proposed as a base for the driverless platoon. The platoon is formed by such road trains, which ensures extended functional features, including the possibility to form platoons of road trains from different logistics centers and with different destinations, quick reforming of the platoon in the logistics centers, possibility to split the platoon when driving on public roads, higher precision of control over the platoon during driving, etc. It is also shown that in order to improve the efficiency of cargo transportation, driverless cargo platforms (trucks) shall be designed without a cabin. The paper also considers the ways to reduce the price of driverless trucks by creating a special road infrastructure, which will allow transfer of the most expensive subsystems of driverless vehicles to such infrastructure. Upon that, the following subsystems will remain within the driverless chassis: navigation, communication, chassis control and ADAS. It is noted that creation of such infrastructure will require high investments, therefore, gradual implementation of such systems is seen as rational. It is shown that the most appropriate area for these purposes is transregional cargo transportation. It is noted that the economic reasons for implementation of the proposed concept are as follows: significant reduction of the number of drivers; significant simplification of the driverless platform control system and reduction of the price of subsystems; no need for the driver’s cabin within the driverless platform; fuel economy when driving within a

  16. Reducing truck emissions at container terminals in a low carbon economy

    DEFF Research Database (Denmark)

    Chen, G.; Govindan, Kannan; Golias, M.M.

    2013-01-01

    This study proposes a methodology to optimize truck arrival patterns to reduce emissions from idling truck engines at marine container terminals. A bi-objective model is developed minimizing both truck waiting times and truck arrival pattern change. The truck waiting time is estimated via...... a queueing network. Based on the waiting time, truck idling emissions are estimated. The proposed methodology is evaluated with a case study, where truck arrival rates vary over time. We propose a Genetic Algorithm based heuristic to solve the resulting problem. Result shows that, a small shift of truck...... arrivals can significantly reduce truck emissions, especially at the gate....

  17. DESIGN OF EXPERIMENTS IN TRUCK COMPANY

    Directory of Open Access Journals (Sweden)

    Bibiana Kaselyova

    2015-07-01

    Full Text Available Purpose: Design of experiment (DOE represent very powerful tool for process improvement vastly supported by six sigma methodology. This approach is mostly used by large and manufacturing orientated companies. Presented research is focused on use of DOE in truck company, which is medium size and service orientated. Such study has several purposes. Firstly, detailed description of improvement effort based on DOE can be used as a methodological framework for companies similar to researched one. Secondly, it provides example of successfully implemented low cost design of experiment practise. Moreover, performed experiment identifies key factors, which influence the lifetime of truck tyres.Design/methodology: The research in this paper is based on experiment conducted in Slovakian Truck Company. It provides detailed case study of whole improvement effort, together with problem formulation, design creation and analysis, as well as the results interpretation. The company wants to improve lifetime of the truck tyres. Next to fuel consumption, consumption of tyres and their replacement represent according to them, one of most costly processes in company. Improvement effort was made through the use of PDCA cycle. It start with analysis of current state of tyres consumption. The variability of tyres consumption based on years and types was investigated. Then the causes of tyres replacement were identified and screening DOE was conducted. After a screening design, the full factorial design of experiment was used to identify main drivers of tyres deterioration and breakdowns. Based on result of DOE, the corrective action were propose and implement.Findings: Based on performed experiment our research describes process of tyres use and replacement. It defines main reasons for tyre breakdown and identify main drivers which influence truck tyres lifetime. Moreover it formulates corrective action to prolong tyres lifetime.Originality: The study represents full

  18. Adaptive Virtual Tow Bar and Transition of Control : A truck driving simulator study

    NARCIS (Netherlands)

    Wilschut, E.S.; Willemsen, D.M.C.; Hogema, J.H.; Martens, M.H.

    2016-01-01

    Background : Truck platooning, with trucks being virtually connected, is getting more and more attention. Truck platooning offers the potential for substantial fuel savings while allowing the truck driver in the platoon to take a rest. However, at the current state of technology, truck drivers are

  19. Noise exposure of truck drivers: a comparative study.

    Science.gov (United States)

    van den Heever, D J; Roets, F J

    1996-06-01

    To investigate the extent of noise exposure to which truck drivers are subjected, a comparison was made of the noise levels in the cabs of two different brands of trucks. Both brands were manufactured with identical engines. The equivalent continuous A-weighted sound pressure levels, maximum sound pressure levels, and percentage noise dose were determined. This study sought to determine if truck drivers are exposed to excessive noise inside the cabs of these trucks. Furthermore, the most beneficial working environment in terms of the brand used was investigated. No significant differences regarding the individual noise exposure of the truck drivers were found (P > 0.05). Based on comparison of measured noise exposures to existing criteria, it was determined that the noise exposures of truck drivers are potentially hazardous to their hearing.

  20. Improving truck safety: Potential of weigh-in-motion technology

    Directory of Open Access Journals (Sweden)

    Bernard Jacob

    2010-07-01

    Full Text Available Trucks exceeding the legal mass limits increase the risk of traffic accidents and damage to the infrastructure. They also result in unfair competition between transport modes and companies. It is therefore important to ensure truck compliance to weight regulation. New technologies are being developed for more efficient overload screening and enforcement. Weigh-in-Motion (WIM technologies allow trucks to be weighed in the traffic flow, without any disruption to operations. Much progress has been made recently to improve and implement WIM systems, which can contribute to safer and more efficient operation of trucks.

  1. Design of an Automatically Tuned Fuzzy Controller for a Truck and Multitrailer System

    Directory of Open Access Journals (Sweden)

    T. R. Ren

    2013-01-01

    Full Text Available The use of a truck and multitrailer system is advantageous because of its ability to transport heavy and large parts with a single powered vehicle. On the other hand, when the system is deployed in an autonomous and unmanned scenario, it remains a challenging task to design a drive controller. Since the drive is only applied to the truck and motivated by successful cases of human expert drivers, a fuzzy controller is developed to generate speed and turn rate commands in order to steer the multi-trailer system to reach the target position with minimum position error. Furthermore, in order to make the controller design efficient and effective, the parameters in the fuzzy controller including the membership functions and rules are automatically tuned using the implementation of efficient particle swarm optimization algorithm instead of relying solely on human expert knowledge. Near-optimal parameters are then derived and adopted in the controller, and drive commands are then generated. The performance of the truck-and-multi-trailer system under fuzzy control is verified through simulation studies, and satisfactory results are obtained.

  2. Unintentional stoppages of trucks hauling high-level nuclear waste in Nevada

    International Nuclear Information System (INIS)

    Glickman, T.S.

    1991-01-01

    Any unintentional stoppage of trucks hauling high-level nuclear waste in Nevada could intensify public concerns about the negative impacts of the Yucca Mountain Project. This paper provides estimates of the expected number and frequency of such stoppages under several alternative scenarios for the routing and volume of the anticipated truck shipments. At least twice as many truck stoppages are expected to occur on freeways as on non-freeways, and at least twice as many are expected to occur in rural areas as in other areas. The expected frequency of such stoppages in the state is estimated to range from about 3 per year to one every 3 1/2 years. About one in every 4 of the stoppages is expected to take place in Las Vegas and 3 out of every 4 are expected to be non-accidents such as mechanical disablements. The minimum duration of the stoppages is expected to be on the order of half an hour for disablements and an hour for accidents

  3. Truck Essential Power Systems Efficiency Improvements for Medium-Duty Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Larry Slone; Jeffrey Birkel

    2007-12-31

    With a variety of hybrid vehicles available in the passenger car market, electric technologies and components of that scale are becoming readily available. Commercial vehicle segments have lagged behind passenger car markets, leaving opportunities for component and system development. Escalating fuel prices impact all markets and provide motivation for OEMs, suppliers, customers, and end-users to seek new techniques and technologies to deliver reduced fuel consumption. The research presented here specifically targets the medium-duty (MD), Class 4-7, truck market with technologies aimed at reducing fuel consumption. These technologies could facilitate not only idle, but also parasitic load reductions. The development efforts here build upon the success of the More Electric Truck (MET) demonstration program at Caterpillar Inc. Employing a variety of electric accessories, the MET demonstrated the improvement seen with such technologies on a Class 8 truck. The Truck Essential Power Systems Efficiency Improvements for Medium-Duty Trucks (TEPS) team scaled the concepts and successes of MET to a MD chassis. The team designed an integrated starter/generator (ISG) package and energy storage system (ESS), explored ways to replace belt and gear-driven accessory systems, and developed supervisory control algorithms to direct the usage of the generated electricity and system behavior on the vehicle. All of these systems needed to fit within the footprint of a MD vehicle and be compatible with the existing conventional systems to the largest extent possible. The overall goal of this effort was to demonstrate a reduction in fuel consumption across the drive cycle, including during idle periods, through truck electrification. Furthermore, the team sought to evaluate the benefits of charging the energy storage system during vehicle braking. The vehicle features an array of electric accessories facilitating on-demand, variable actuation. Removal of these accessories from the belt or

  4. Modernization of dump truck onboard system

    Science.gov (United States)

    Semenov, M. A.; Bolshunova, O. M.; Korzhev, A. A.; Kamyshyan, A. M.

    2017-10-01

    The review of the only automated dispatch system for the career dump trucks, which is presented in the domestic market, was made. A method for upgrading the loading control system and technological weighing process of the career dump was proposed. The cargo weight during loading is determined by the gas pressure in the suspension cylinders at the time of the oscillation ending and at the start of the vibration smoothing process; the smoothing speed correction is performed. The error of the cargo weighting is 2.5-3%, and of the technological weighing process during driving - 1%, which corresponds to the error level of the steady-state weighting means.

  5. Truck Roll Stability Data Collection and Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, SS

    2001-07-02

    The principal objective of this project was to collect and analyze vehicle and highway data that are relevant to the problem of truck rollover crashes, and in particular to the subset of rollover crashes that are caused by the driver error of entering a curve at a speed too great to allow safe completion of the turn. The data are of two sorts--vehicle dynamic performance data, and highway geometry data as revealed by vehicle behavior in normal driving. Vehicle dynamic performance data are relevant because the roll stability of a tractor trailer depends both on inherent physical characteristics of the vehicle and on the weight and distribution of the particular cargo that is being carried. Highway geometric data are relevant because the set of crashes of primary interest to this study are caused by lateral acceleration demand in a curve that exceeds the instantaneous roll stability of the vehicle. An analysis of data quality requires an evaluation of the equipment used to collect the data because the reliability and accuracy of both the equipment and the data could profoundly affect the safety of the driver and other highway users. Therefore, a concomitant objective was an evaluation of the performance of the set of data-collection equipment on the truck and trailer. The objective concerning evaluation of the equipment was accomplished, but the results were not entirely positive. Significant engineering apparently remains to be done before a reliable system can be fielded. Problems were identified with the trailer to tractor fiber optic connector used for this test. In an over-the-road environment, the communication between the trailer instrumentation and the tractor must be dependable. In addition, the computer in the truck must be able to withstand the rigors of the road. The major objective--data collection and analysis--was also accomplished. Using data collected by instruments on the truck, a ''bad-curve'' database can be generated. Using

  6. Design and fabrication of a multipurpose railroad hand truck ...

    African Journals Online (AJOL)

    A multipurpose railroad hand truck comprising mainly of a frame, swinger arm, connecting rod, crank shaft, gears, wheels and brake was designed and fabricated to reduce the cost of material handling in small scaled manufacturing industries. The frame and other major components of the hand truck were fabricated with ...

  7. Truck Route Choice Modeling using Large Streams of GPS Data

    Science.gov (United States)

    2017-07-31

    The primary goal of this research was to use large streams of truck-GPS data to analyze travel routes (or paths) chosen by freight trucks to travel between different origin and destination (OD) location pairs in metropolitan regions of Florida. Two s...

  8. 29 CFR 1910.178 - Powered industrial trucks.

    Science.gov (United States)

    2010-07-01

    ... section does not apply to compressed air or nonflammable compressed gas-operated industrial trucks, nor to farm vehicles, nor to vehicles intended primarily for earth moving or over-the-road hauling. (2) All..., except for vehicles intended primarily for earth moving or over-the-road hauling. (3) Approved trucks...

  9. Optimising Shovel-Truck Fuel Consumption using Stochastic ...

    African Journals Online (AJOL)

    Optimising the fuel consumption and truck waiting time can result in significant fuel savings. The paper demonstrates that stochastic simulation is an effective tool for optimising the utilisation of fossil-based fuels in mining and related industries. Keywords: Stochastic, Simulation Modelling, Mining, Optimisation, Shovel-Truck ...

  10. Waste Management's LNG Truck Fleet: Final Results

    Energy Technology Data Exchange (ETDEWEB)

    Chandler, K. [Battelle (US); Norton, P. [National Renewable Energy Laboratory (US); Clark, N. [West Virginia University (US)

    2001-01-25

    Waste Management, Inc., began operating a fleet of heavy-duty LNG refuse trucks at its Washington, Pennsylvania, facility. The objective of the project was to provide transportation professionals with quantitative, unbiased information on the cost, maintenance, operational, and emissions characteristics of LNG as one alternative to conventional diesel for heavy-duty trucking applications.

  11. 49 CFR 215.119 - Defective freight car truck.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defective freight car truck. 215.119 Section 215... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD FREIGHT CAR SAFETY STANDARDS Freight Car Components Suspension System § 215.119 Defective freight car truck. A railroad may not place or continue in service a...

  12. The effect of see-through truck on driver monitoring patterns and responses to critical events in truck platooning

    NARCIS (Netherlands)

    Zhang, B.; Wilschut, E.S.; Willemsen, D.M.C.; Alkim, T.; Martens, M.H.

    2018-01-01

    Automated platooning of trucks has its beneficial effects on energy saving and traffic flow efficiency. The vehicles in a platoon, however, need to maintain an extremely short headway to achieve these goals, which will result in a heavily blocked front view for the driver in a following truck.

  13. Emissions and air quality impacts of truck-to-rail freight modal shifts in the Midwestern United States.

    Science.gov (United States)

    Bickford, Erica; Holloway, Tracey; Karambelas, Alexandra; Johnston, Matt; Adams, Teresa; Janssen, Mark; Moberg, Claus

    2014-01-01

    We present an examination of the potential emissions and air quality benefits of shifting freight from truck to rail in the upper Midwestern United States. Using a novel, freight-specific emissions inventory (the Wisconsin Inventory of Freight Emissions, WIFE) and a three-dimensional Eulerian photochemical transport model (the Community Multiscale Air Quality Model, CMAQ), we quantify how specific freight mode choices impact ambient air pollution concentrations. Using WIFE, we developed two modal shift scenarios: one focusing on intraregional freight movements within the Midwest and a second on through-freight movements through the region. Freight truck and rail emissions inventories for each scenario were gridded to a 12 km × 12 km horizontal resolution as input to CMAQ, along with emissions from all other major sectors, and three-dimensional time-varying meteorology from the Weather Research and Forecasting model (WRF). The through-freight scenario reduced monthly mean (January and July) localized concentrations of nitrogen dioxide (NO2) by 28% (-2.33 ppbV) in highway grid cells, and reduced elemental carbon (EC) by 16% (-0.05 μg/m(3)) in highway grid cells. There were corresponding localized increases in railway grid cells of 25% (+0.83 ppbV) for NO2, and 22% (+0.05 μg/m(3)) for EC. The through-freight scenario reduced CO2 emissions 31% compared to baseline trucking. The through-freight scenario yields a July mean change in ground-level ambient PM2.5 and O3 over the central and eastern part of the domain (up to -3%).

  14. Roads and Roadlessness: Driving Trucks in Siberia

    Directory of Open Access Journals (Sweden)

    Tatiana Argounova-Low

    2012-06-01

    Full Text Available This article relates to the studies of roads and engages with the experience of driving in Sakha (Yakutiia, Siberia. The article intends to contribute to the broad corpus of literature on mobility and argues that an alternative perspective on roads and road-users from a geographical area beyond the West might better inform and add another dimension to our notions of roads and our movement along them. The article examines the fluid nature of roads in Siberia and the social significance the roads carry by focussing on truck-drivers and their perception and engagement with the so-called winter roads through their sensory experiences. The article analyses narratives of the truckers who frame their experiences of the road with close reference to time and money and where notions of agency of the road become prominent.

  15. FHWA scenario planning guidebook

    Science.gov (United States)

    2011-02-01

    The purpose of this guidebook is to assist transportation agencies with carrying out a scenario : planning process from start to finish. Transportation agencies can use the guidebook as a framework : to develop a scenario planning approach tailored t...

  16. Participatory Scenario Planning

    DEFF Research Database (Denmark)

    Rasmussen, Lauge Baungaard

    2006-01-01

    The paper describes the paradigm, framework and a guideline how to use scenario methods in a workshop......The paper describes the paradigm, framework and a guideline how to use scenario methods in a workshop...

  17. Exposure scenarios for workers

    NARCIS (Netherlands)

    Marquart, H.; Northage, C.; Money, C.

    2007-01-01

    The new European chemicals legislation REACH (Registration, Evaluation, Authorisation and restriction of Chemicals) requires the development of Exposure Scenarios describing the conditions and risk management measures needed for the safe use of chemicals. Such Exposure Scenarios should integrate

  18. Truck Drivers' Use of the Internet: A Mobile Health Lifeline.

    Science.gov (United States)

    Heaton, Karen; Combs, Bryan; Griffin, Russell

    2017-06-01

    Because of their social isolation, irregular and unpredictable schedules, limited access to health care, and long periods of travel, long-haul truckers may benefit from the use of mobile health applications on Internet-capable devices. The purpose of this study was to determine Internet access and usage among a sample of long-haul truck drivers. In this cross-sectional study, truck drivers completed a pencil and paper survey with questions on demographics, work and health histories, and Internet access and usage for both personal and job reasons. A total of 106 truck drivers were recruited from trucking industry trade shows, by word of mouth, and directly from trucking companies. Overall, the truck drivers' use of the Internet was limited. Their usage for personal and job-related reasons differed. Social connectivity and access to health and wellness information were important during personal usage time. Job-related Internet use was highly practical, and applied to seeking information for directions and maps, fuel stops and pricing, and communicating with employers or transmitting documents. Age and experience were associated with Internet use. Younger, less-experienced drivers used the Internet more than older, experienced drivers. Targeted mobile health messaging may be a useful tool to inform truck drivers of health conditions and plans, and may provide links to primary care providers needing to monitor or notify drivers of diagnostic results or treatment plans.

  19. Collision avoidance for mine haul trucks

    Energy Technology Data Exchange (ETDEWEB)

    Patrick Glynn; Jim Slade; John Marston [CSIRO Exploration & Mining (Australia). Control Technologies International

    2007-03-15

    A suite of new collision avoidance systems (CAS) is presented for use in heavy vehicles whose structure and size necessarily impede driver visibility is introduced. The main goal of the project was to determine the appropriate use of each of the commercially available technologies and, where possible, produce a low cost variant suitable for use in proximity detection on large mining industry haul trucks. CAS variants produced were subjected to a field demonstration and, linked to the output from the earlier CAS 1 project. The CAS 2 system used low cost Doppler continuous wave radar antennae coupled to the CAS 1 monitor to indicate the presence of an object moving at any speed above 3 Km/h relative to the antennae. The novelty of the CAS 3 system lies in the design of 3 interconnected, modules. CAS 4 expanded on the research in CAS 3 the Doppler radar antennae functionality was increased to allow object detection discrimination. This reduced the high bandwidth required by and essentially only informed the driver when an object was detected. The radar antennae modules and the system as a whole are described together with the empirical tests conducted and results obtained. The tests, drawing on Monte-Carlo simulation techniques, demonstrate both the 'correctness' of the implementations and the effectiveness of the system. The results of the testing of the final prototype unit were highly successful both as a computer simulation level and in practical tests on light vehicles. Chapter 9 reports on CAS 4 with the new microcontroller based fast Fourier transforms of the returned Doppler signals to give multiple object detection, speed and distance. A prototype of this system was installed on a Caterpillar 737D haul truck at the BMA Goonyella mine and tested for object detection and general robustness of the CAS 4 system.

  20. A framework for improving reliability of truck turn times in FMCG transport networks

    NARCIS (Netherlands)

    Ploos van Amstel, W.; Clermonts, W.

    2013-01-01

    Truck turn times in FMCG supply chain are unreliable. The Dutch ‘Speed Docking’ project in 2011 and 2012 gave clear evidence to this. This leads to additional trucks and drivers in transport networks. Improving reliability of truck turn time will lead to less trucks and drivers in the transport

  1. Learning Through Scenario Planning

    DEFF Research Database (Denmark)

    Balarezo, Jose

    This project investigates the uses and effects of scenario planning in companies operating in highly uncertain and dynamic environments. Whereas previous research on scenario planning has fallen short of providing sufficient evidence of its mechanisms and effects on individual or organizational l...... theoretical understanding of scenario planning while simultaneously presenting a more nuanced account of the individual behaviors and social dynamics underpinning organizational learning.......This project investigates the uses and effects of scenario planning in companies operating in highly uncertain and dynamic environments. Whereas previous research on scenario planning has fallen short of providing sufficient evidence of its mechanisms and effects on individual or organizational...... level variables, this research corrects this void by investigating the dynamics of organizational learning through the lenses of a corporate scenario planning process. This enhances our scientific understanding of the role that scenario planning might play in the context of organizational learning...

  2. Analysis of the truck inventory and use survey from the truck size and weight perspective for trucks with four-axles or less : activity 1 : Task B identify market segments - competitive and noncompetitive TIUS data component

    Science.gov (United States)

    1996-10-01

    This report, as part of the U.S. Department of Transportation (DOT) Comprehensive Truck Size and Weight (TS&W) Study, provides factual information and analysis of the U.S. freight hauling truck fleet, and is based on the Truck Inventory and Use Surve...

  3. Parametric Analysis of Light Truck and Automobile Maintenance

    Science.gov (United States)

    1979-05-01

    Utilizing the Automotive and Light Truck Service and Repair Data Base developed in the campanion report, parametric analyses were made of the relationships between maintenance costs, schduled and unschduled, and vehicle parameters; body class, manufa...

  4. The Aerodynamics of Heavy Vehicles III : Trucks, Buses and Trains

    CERN Document Server

    Orellano, Alexander

    2016-01-01

    This volume contains papers presented at the International conference “The Aerodynamics of Heavy Vehicles III: Trucks, Buses and Trains” held in Potsdam, Germany, September 12-17, 2010 by Engineering Conferences International (ECI). Leading scientists and engineers from industry, universities and research laboratories, including truck and high-speed train manufacturers and operators were brought together to discuss computer simulation and experimental techniques to be applied for the design of more efficient trucks, buses and high-speed trains in the future.   This conference was the third in the series after Monterey-Pacific Groove in 2002 and Lake Tahoe in 2007.  The presentations address different aspects of train aerodynamics (cross wind effects, underbody flow, tunnel aerodynamics and aeroacoustics, experimental techniques), truck aerodynamics (drag reduction, flow control, experimental and computational techniques) as well as computational fluid dynamics and bluff body, wake and jet flows.

  5. Seismic hazard assessment of Oregon highway truck routes.

    Science.gov (United States)

    2012-06-01

    This research project developed a seismic risk assessment model along the major truck routes in Oregon. The study had adopted federally : developed software tools called Risk for Earthquake Damage to Roadway Systems (REDARS2) and HAZUS-MH. The model ...

  6. Commercial truck platooning demonstration in Texas – level 2 automation.

    Science.gov (United States)

    2017-08-01

    Through this project, the Texas Department of Transportation (TxDOT) funded the creation of a comprehensive truck platooning demonstration in Texas, serving as a proactive effort in assessing innovative operational strategies to position TxDOT as a l...

  7. Overload truck wheel load distribution on bridge decks.

    Science.gov (United States)

    2009-04-01

    There is a need to accurately analyze the load effects on bridge decks from permitted overload trucks on : Michigans roads. The AASHTO Standard Specifications for Highway Bridges, 17th edition, provides a : distribution width of live loads when re...

  8. 1990 Nationwide Truck Activity and Commodity Survey selected tabulations

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    The Nationwide Truck Activity and Commodity Survey (NTACS) provides detailed activity data for a sample of trucks covered in the 1987 Truck Inventory and Use Survey (TIUS) for days selected at random over a 12-month period ending in 1990. The NTACS was conducted by the US Bureau of the Census for the US Department of Transportation (DOT). A Public Use File for the NTACS was developed by Oak Ridge National Laboratory (ORNL) under a reimbursable agreement with the DOT. The content of the Public Use File and the detailed design of the NTACS are described in the ORNL Report [open quotes]Technical Documentation for the 1990 Nationwide Truck Activity and Commodity Survey Public Use File[close quotes]. (1992). ORNL Technical Report No. TM-12188, Oak Ridge National Laboratory, Oak Ridge, TN 37831. The main purpose of this summary report is to provide selected tables based on the public use file.

  9. Market capitalization of the trucking industry sector, 2005

    Science.gov (United States)

    2006-08-01

    This report focuses on the market valuation of the overall trucking industry sector and each segment within it. In the past, while the focus has been on stock price appreciation or depreciation, this report emphasizes market capitalization returns. S...

  10. Arctic Planning Scenarios: Scenario #2 - Safety and Security Scenario

    Science.gov (United States)

    2011-07-01

    By: Lansdowne Technologies Inc. 1001-247 Slater Street Ottawa ON, K1P 5H9 Contractor’s Document Number: Contract Project Manager : Peter Avis... management , focusing on eliciting a Whole of Government (WoG) response. While all efforts have been taken to present a plausible scenario, it is not...capabilities required for Canada to be able to meet its strategy and policy objectives. Résumé …..... Compte tenu des changements survenus dans le climat

  11. TeleTruck : a holonic fleet management system

    OpenAIRE

    Bürckert, Hans-Jürgen; Fischer, Klaus; Vierke, Gero

    1997-01-01

    In this paper we describe TeleTruck, a multiagent dispatching system that was developed in close cooperation with a forwarding company and that is capable of handling real-world requirements like dynamics and uncertainty. The main idea underlying the TeleTruck approach is the usage of holonic agents, i.e. agents composed of subagents that act in a corporated way. We describe the implementation in detail and point out the advantages of the holonic paradigm.

  12. The world in scenarios

    International Nuclear Information System (INIS)

    De Jong, A.; Roodenburg, H.

    1992-01-01

    As an introduction to this special issue 'Worlds of difference: Scenarios's for the economy, energy and the environment 1990-2015', an outline is given of the future of the world and the Netherlands, based on four scenarios. These scenarios are published in 'Scanning the future' in May 1992 by the CPB, the Dutch Central Planning Bureau. The Global Shift (GS) scenario is characterized by a very dynamic technological development, the free market perspective, strong economic growth in the Asian economies, and a relative economic regression in Western Europe. In the European Renaissance (ER) scenario the technological development is less dynamic and more gradual than in the GS scenario. The Balanced Growth (BG) scenario is dominated by a sustainable economic development and a strong technological dynamic development. The Global Crisis (GC) scenario shows a downward spiral in many areas, stagnating developments and fragile economies as results of the trends in the eighties. The first three scenarios are elaborated for the Netherlands. Also attention is paid to the aims and meaning of long-term scenarios. 2 figs., 2 tabs., 3 refs

  13. Application of Chaos Theory in Trucks' Overloading Enforcement

    Directory of Open Access Journals (Sweden)

    Abbas Mahmoudabadi

    2013-01-01

    Full Text Available Trucks' overloading is considered as one of the most substantial concerns in road transport due to a possible road surface damage, as well as, are less reliable performance of trucks' braking system. Sufficient human resource and adequate time scheduling are to be planned for surveying trucks' overloading; hence, it seems required to prepare an all-around model to be able to predict the number of overloaded vehicles. In the present research work, the concept of chaos theory has been utilized to predict the ratio of trucks which might be guessed overloaded. The largest Lyapunov exponent is utilized to determine the presence of chaos using experimental data and concluded that the ratio of overloaded trucks reflects chaotic behavior. The prediction based on chaos theory is compared with the results of simple smoothing and moving average methods according to the well-known criterion of mean square errors. The results have also revealed that the chaotic prediction model would act more capably comparing the analogous methods including simple smoothing and moving average to predict the ratio of passing trucks to be possibly overloaded.

  14. The Aggregate Planning For Trucking Operation in Cikarang Dry Port

    Directory of Open Access Journals (Sweden)

    Dwi Puspita Sari Utami

    2015-06-01

    Full Text Available Abstract. Cikarang Dry Port currently is the only dry port in Indonesia. This Dry Port has a role to connect or extend the Sea Port to the industrial areas located far from Sea Port. Thus, it creates a value added and also reduce costs. One of the operations done in Cikarang Dry Port is trucking operation. This research aims to examine the planning of 2014 trucking activity in Cikarang Dry Port to determine the right number of the truck that will be best occupied to manage all demands. The analysis begins with demand forecasting by using a moving average method of 12 months or one year period in 2013 which will be used as main information to develop the plans. There are three plans developed in this research. Based on the three plans, Plan A with minimum trucking plan with subcontracting is the most profitable which gives the highest profitability of Rp. 374,984,625. Recommendation for this research is using the current minimum number of 39 trucks rent with additional subcontracting when the demand is exceeding the capacity, thus, Cikarang Dry Port can occupy all demands and gain more profits. Keywords: Aggregate Planning; Scheduling; Trucking Operation; Moving Average; Cikarang Dry Port

  15. Food scenarios 2025

    DEFF Research Database (Denmark)

    Sundbo, Jon

    2016-01-01

    This article presents the results of a future study of the food sector. Two scenarios have been developed using a combination of: 1) a summary of the relevant scientific knowledge, 2) systematic scenario writing, 3) an expert-based Delphi technique, and 4) an expert seminar assessment. The two...... scenarios present possible futures at global, national (Denmark) and regional (Zealand, Denmark) levels. The main scenario is called ‘Food for ordinary days and celebrations’ (a combination of ‘High-technological food production − The functional society’ and ‘High-gastronomic food − The experience society......’). A less likely scenario is called ‘The reappearence of the sea − The aquarial society’. The purpose of the scenario writing has been to provide strategic tools for societal actors who to create economic growth and jobs, particularly regional governments and firms. Suggestions concerning regional...

  16. Particle Reduction Strategies - PAREST. Traffic emission modelling. Model comparision and alternative scenarios. Sub-report

    International Nuclear Information System (INIS)

    Kugler, Ulrike; Theloke, Jochen; Joerss, Wolfram

    2013-01-01

    The modeling of the reference scenario and the various reduction scenarios in PAREST was based on the Central System of Emissions (CSE) (CSE, 2007). Emissions from road traffic were calculated by using the traffic emission model TREMOD (Knoerr et al., 2005) and fed into the CSE. The version TREMOD 4.17 has been used. The resulting emission levels in PAREST reference scenario were supplemented by the emission-reducing effect of the implementation of the future Euro 5 and 6 emission standards for cars and light commercial vehicles and Euro VI for heavy commercial vehicles in combination with the truck toll extension. [de

  17. Food scenarios 2025

    DEFF Research Database (Denmark)

    Sundbo, Jon

    2016-01-01

    scenarios present possible futures at global, national (Denmark) and regional (Zealand, Denmark) levels. The main scenario is called ‘Food for ordinary days and celebrations’ (a combination of ‘High-technological food production − The functional society’ and ‘High-gastronomic food − The experience society......This article presents the results of a future study of the food sector. Two scenarios have been developed using a combination of: 1) a summary of the relevant scientific knowledge, 2) systematic scenario writing, 3) an expert-based Delphi technique, and 4) an expert seminar assessment. The two...

  18. Scenario-based strategizing

    DEFF Research Database (Denmark)

    Lehr, Thomas; Lorenz, Ullrich; Willert, Markus

    2017-01-01

    For over 40 years, scenarios have been promoted as a key technique for forming strategies in uncertain en- vironments. However, many challenges remain. In this article, we discuss a novel approach designed to increase the applicability of scenario-based strategizing in top management teams. Drawing...... on behavioural strategy as a theoretical lens, we design a yardstick to study the impact of scenario-based strategizing. We then describe our approach, which includes developing scenarios and alternative strategies separately and supporting the strategy selection through an integrated assessment of the goal...... Ministry) and a firm affected by disruptive change (Bosch, leading global supplier of technology and solutions)....

  19. Truck accident involving unirradiated nuclear fuel

    International Nuclear Information System (INIS)

    Carlson, R.W.; Fischer, L.E.

    1992-07-01

    In the early morning of Dec. 16, 1991, a severe accident occurred when a passenger vehicle traveling in the wrong direction collided with a tractor trailer carrying 24 nuclear fuel assemblies in 12 containers on Interstate 1-91 in Springfield, Massachusetts. This paper documents the mechanical circumstances of the accident and the physical environment to which the containers were exposed and the response of the containers and their contents. The accident involved four impacts where the truck was struck by the car, impacted on the center guardrail, impacted on the outer concrete barrier and came to rest against the center guardrail. The impacts were followed by a fire that began in the engine compartment, spread to the.tractor and cab, and eventually spread to the trailer and payload. The fire lasted for about three hours and the packages were involved in the fire for about two hours. As a result of the fire, the tractor-trailer was completely destroyed and the packages were exposed to flames with temperatures between 1300 degrees F and 1800 degrees F. The fuel assemblies remained intact during the accident and there was no release of any radioactive material during the accident. This was a very severe accident; however, the injuries were minor and at no time was the public health and safety at risk

  20. 26 CFR 145.4051-1 - Imposition of tax on heavy trucks and trailers sold at retail.

    Science.gov (United States)

    2010-04-01

    ...) Automobile truck chassis and bodies; (ii) Truck trailer and semitrailer chassis and bodies; and (iii.... No tax is imposed by section 4051(a)(1) on the sale of automobile truck chassis and bodies, suitable.... A sale of an automobile truck, truck trailer or semitrailer, shall be considered to be a sale of a...

  1. Estimating truck operating costs for domestic trips – case studies from Greece

    Directory of Open Access Journals (Sweden)

    Sdoukopoulos Eleftherios

    2015-11-01

    Full Text Available The transport sector represents a vital component of national economies and has significant impacts on productivity and social welfare. In 2012, the transport sector in Europe was estimated to account for 3.7% of the European Gross Domestic Product (GDP and 5.1% for employment. Road transport proves to be the predominant mode for moving goods within Europe holding a share of approximately 45.8% in 2012 (in ton-kms. In Greece, the share of road freight transport is significantly higher (98% indicating the importance of this sector for the Greek economy. To this end and considering the existing needs of road freight transport operators in Greece, the objective of this research is to establish an analytical and documented basis for estimating the operating cost of a truck on specific urban or national freight transport routes. To achieve this goal, an extended literature review has been conducted resulting in the identification of the main components comprising the total truck operating cost, which were then updated and validated through a series of personal interviews with selected road freight transport professionals. An excel-based application tool was also developed in order to facilitate operating cost estimates for different cases, through selection of the proper values of the relevant parameters. The resulting tool was used to analyse four test cases, which demonstrate the tool’s usability and applicability. Results from this analysis have been also validated by industry experts and they reflect real-world transport scenarios.

  2. Management of Truck Loading Weight: A Critical Review of the Literature and Recommended Remedies

    Directory of Open Access Journals (Sweden)

    Aliakbari Mozhgan

    2016-01-01

    Full Text Available Traffic accidents involving heavy trucks have social and economic effects on society. However, little research has focused on the influence of heavy truck specifications such as weight. Apportioning the maximum permissible gross weight of trucks allows trucking companies/owners to consolidate loads, and therefore reduce the vehicle-kilometres required to collect and distribute a given amount of goods/material. While drivers/managers are responsible for ensuring that trucks are loaded appropriately and in compliance with regulations, some may take chances and overload vehicles. This increases the need for formal and documented inspections, in order to reduce traffic hazards on public roads due to overweight loading. According to a New South Wales Centre for Road Safety report in 2014, crashes involving heavy trucks often result in serious road trauma outcomes. When a heavy truck is involved in a crash, the vehicle mass raises the crash forces involved and hence increases the severity of the crash. Therefore, interventions should be established to mitigate or prevent these crashes from occurring. Currently, weight checks are required for trucks and truck drivers must drive to a weighbridge for a weight check. Since this is a random process, truck drivers may take the risk of driving an over-loaded truck on some occasions. This paper reviews existing studies concerning safe system interventions in relation to truck gross weight management and a framework is presented to effectively manage truck loading weight. The result may be a reduction of injuries and fatalities involving heavy trucks.

  3. Nuclear Security Futures Scenarios

    International Nuclear Information System (INIS)

    Keller, Elizabeth James Kistin; Warren, Drake Edward; Hayden, Nancy Kay; Passell, Howard D.; Malczynski, Leonard A.; Backus, George A.

    2017-01-01

    This report provides an overview of the scenarios used in strategic futures workshops conducted at Sandia on September 21 and 29, 2016. The workshops, designed and facilitated by analysts in Center 100, used scenarios to enable thought leaders to think collectively about the changing aspects of global nuclear security and the potential implications for the US Government and Sandia National Laboratories.

  4. Nuclear Security Futures Scenarios.

    Energy Technology Data Exchange (ETDEWEB)

    Keller, Elizabeth James Kistin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Warren, Drake Edward [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hayden, Nancy Kay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Passell, Howard D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Malczynski, Leonard A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Backus, George A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-01-01

    This report provides an overview of the scenarios used in strategic futures workshops conducted at Sandia on September 21 and 29, 2016. The workshops, designed and facilitated by analysts in Center 100, used scenarios to enable thought leaders to think collectively about the changing aspects of global nuclear security and the potential implications for the US Government and Sandia National Laboratories.

  5. Demonstration of fleet trucks fueled with PV hydrogen

    International Nuclear Information System (INIS)

    Provenzano, J.; Scott, P.B.; Zweig, R.

    1998-01-01

    The Clean Air Now (CAN) Solar Hydrogen Project has been installed at the Xerox Corporation, El Segundo, California site. Three Ford Ranger trucks have been converted to use hydrogen fuel. The ''stand- alone'' electrolyzer and hydrogen dispensing system is powered by a photovoltaic array with no connection to the power grid. A variable frequency DC/AC converter steps up the voltage to drive the 15 hp motor for the hydrogen compressor. Up to 400 standard cubic meters (SCM) of solar hydrogen is stored, and storage of up to 2300 SCM of commercial hydrogen is collocated. As the hydrogen storage is within 5km of Los Angeles International Airport, pilot operation of a hydrogen fuel cell bus for airport shuttle service has been demonstrated with fueling at the CAN facility. The truck engine conversions are bored to 2.91 displacement, use a Roots type supercharger and CVI (constant volume injection) fuel induction to allow performance similar to that of the gasoline powered truck. Truck fuel storage is done with carbon composite tanks at pressures up to 24.8 MPa (3600 psi). Two tanks are located just behind the driver's cab, and take up nearly half of the truck bed space. The truck highway range is approximately 140 miles. The engine operates in lean burn mode, with nil emissions of CO and HC. NO x emissions vary with load and rpm in the range from 10 to 100 ppm, yielding total emissions at a small fraction of the ULEV standard. Two Xerox fleet trucks have been converted, and one for the City of West Hollywood. The Clean Air Now Program demonstrates that hydrogen powered fleet development is an appropriate safe, and effective strategy for improvement of urban air quality. It further demonstrates that continued technological development and cost reduction will make such implementation competitive. (Author)

  6. Experimental Measurement of the Flow Field of Heavy Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Fred Browand; Charles Radovich

    2005-05-31

    Flat flaps that enclose the trailer base on the sides and top are known to reduce truck drag and reduce fuel consumption. Such flapped-truck geometries have been studied in laboratory wind tunnels and in field tests. A recent review of wind tunnel data for a variety of truck geometries and flow Reynolds numbers show roughly similar values of peak drag reduction, but differ in the determination of the optimum flap angle. Optimum angles lie in the range 12 degrees-20 degrees, and may be sensitive to Reynolds number and truck geometry. The present field test is undertaken to provide additional estimates of the magnitude of the savings to be expected on a typical truck for five flap angles 10, 13, 16, 19, and 22 degrees. The flaps are constructed from a fiberglass-epoxy-matrix material and are one-quarter of the base width in length (about 61 cm, or 2 feet). They are attached along the rear door hinge lines on either side of the trailer, so that no gap appears at the joint between the flap and the side of the trailer The flap angle is adjusted by means of two aluminum supports. The present test is performed on the NASA Crows Landing Flight Facility at the northern end of the San Joaquin valley in California. The main runway is approximately 2400 meters in length, and is aligned approximately in a north-south direction The test procedure is to make a series of runs starting at either end of the runway. All runs are initiated under computer control to accelerate the truck to a target speed of 60 mph (96 6 km/hr), to proceed at the target speed for a fixed distance, and to decelerate at the far end of the runway. During a run, the broadcast fuel rate, the engine rpm, forward speed, elapsed time--as well as several other parameters (10 in all)--are digitized at a rate of 100 digitizations per second. Various flapped-conditions are interspersed with the ''no flaps'' control, and are sequenced in a different order on different days. Approximately 310 runs

  7. Acceptance test report for core sample trucks 3 and 4

    International Nuclear Information System (INIS)

    Corbett, J.E.

    1996-01-01

    The purpose of this Acceptance Test Report is to provide documentation for the acceptance testing of the rotary mode core sample trucks 3 and 4, designated as HO-68K-4600 and HO-68K-4647, respectively. This report conforms to the guidelines established in WHC-IP-1026, ''Engineering Practice Guidelines,'' Appendix M, ''Acceptance Test Procedures and Reports.'' Rotary mode core sample trucks 3 and 4 were based upon the design of the second core sample truck (HO-68K-4345) which was constructed to implement rotary mode sampling of the waste tanks at Hanford. Successful completion of acceptance testing on June 30, 1995 verified that all design requirements were met. This report is divided into four sections, beginning with general information. Acceptance testing was performed on trucks 3 and 4 during the months of March through June, 1995. All testing was performed at the ''Rock Slinger'' test site in the 200 West area. The sequence of testing was determined by equipment availability, and the initial revision of the Acceptance Test Procedure (ATP) was used for both trucks. Testing was directed by ICF-KH, with the support of WHC Characterization Equipment Engineering and Characterization Project Operations. Testing was completed per the ATP without discrepancies or deviations, except as noted

  8. Urban Freight Truck Routing under Stochastic Congestion and Emission Considerations

    Directory of Open Access Journals (Sweden)

    Taesung Hwang

    2015-05-01

    Full Text Available Freight trucks are known to be a major source of air pollutants as well as greenhouse gas emissions in U.S. metropolitan areas, and they have significant effects on air quality and global climate change. Emissions from freight trucks during their deliveries should be considered by the trucking service sector when they make routing decisions. This study proposes a model that incorporates total delivery time, various emissions including CO2, VOC, NOX, and PM from freight truck activities, and a penalty for late or early arrival into the total cost objective of a stochastic shortest path problem. We focus on urban transportation networks in which random congestion states on each link follows an independent probability distribution. Our model finds the best truck routing on a given network so as to minimize the expected total cost. This problem is formulated into a mathematical model, and two solution algorithms including a dynamic programming approach and a deterministic shortest path heuristic are proposed. Numerical examples show that the proposed approach performs very well even for the large-size U.S. urban networks.

  9. Integrated transportation scenario planning.

    Science.gov (United States)

    2010-07-01

    Regional land usetransportation scenario planning emerged as a planning technique in U.S. : metropolitan areas in the 1990s. Building on prior work by this research team, this study continues : to track the development and expansion of regional sc...

  10. Learning Through Scenario Planning

    DEFF Research Database (Denmark)

    Balarezo, Jose

    This project investigates the uses and effects of scenario planning in companies operating in highly uncertain and dynamic environments. Whereas previous research on scenario planning has fallen short of providing sufficient evidence of its mechanisms and effects on individual or organizational...... level variables, this research corrects this void by investigating the dynamics of organizational learning through the lenses of a corporate scenario planning process. This enhances our scientific understanding of the role that scenario planning might play in the context of organizational learning...... and strategic renewal. Empirical evidence of the various difficulties that learning flows has to overcome as it journeys through organizational and hierarchical levels are presented. Despite various cognitive and social psychological barriers identified along the way, the results show the novel...

  11. Supplying of Assembly Lines Using Train of Trucks

    Science.gov (United States)

    Čujan, Zdeněk; Fedorko, Gabriel

    2016-11-01

    The typical supply system conceptions, i.e. the concepts "Just-in-time" (JIT) and "Just-in-sequence" (JIS) are very important factors with regard to a fluent operation of the assembly lines. Therefore the contemporary intra plant transport systems are being replaced by a new kind of the transportation technology, namely by means of the trains of trucks. The trains of trucks are used in two possible operational modes: either with a driver or without driver (fully automated). The trucks of the logistic trains are also cheaper and they are able to carry a larger volume and mass of the material at once. There are reduced in this way not only the investment costs, but also the operational expenses.

  12. Smoldering - The Fire Scenario

    OpenAIRE

    Torero, Jose L

    2000-01-01

    There are certain fire initiation scenarios that are particularly common, one of great significance is a fire initiated from the ignition of a porous fuel. Nearly 40% of the deaths due to fire can be traced to cigarette induced smolder of upholstered furniture and the mechanisms that control the process that transforms the weak smolder reaction occurring in the cigarette to a fire are still mostly unknown. A general description of this fire scenario and a discussion of its threats is pr...

  13. Heavy truck modeling for fuel consumption. Simulations and measurements

    Energy Technology Data Exchange (ETDEWEB)

    Sandberg, T.

    2001-12-01

    Fuel consumption for heavy trucks depends on many factors like roads, weather, and driver behavior that are hard for a manufacturer to influence. However, one design possibility is the power train configuration. Here a new simulation program for heavy trucks is created to find the configuration of the power train that gives the lowest fuel consumption for each transport task. For efficient simulations the model uses production code for speed and gear control, and it uses exchangeable data sets to allow simulation of the whole production range of engine types, on recorded road profiles from all over the world. Combined with a graphical user interface this application is called STARS (Scania Truck And Road Simulation). The forces of rolling resistance and air resistance in the model are validated through an experiment where the propeller shaft torque of a heavy truck is measured. It is found that the coefficient of rolling resistance is strongly dependent on tire temperature, not only on vehicle speed as expected. This led to the development of a new model for rolling resistance. The model includes the dynamic behavior of the tires and relates rolling resistance to tire temperature and vehicle speed. In another experiment the fuel consumption of a test truck in highway driving is measured. The altitude of the road is recorded with a barometer and used in the corresponding simulations. Despite of the limited accuracy of this equipment the simulation program manage to predict a level of fuel consumption only 2% lower than the real measurements. It is concluded that STARS is a good tool for predicting fuel consumption for trucks in highway driving and for comparing different power train configurations.

  14. Weight Reduction Potential of Automobiles and Light Trucks: 1980 Summary Source Document

    Science.gov (United States)

    1981-06-01

    This report provides an assessment of the potential of weight reduction for passenger cars and light trucks (including pickup trucks, vans, and utility vehicles of GVWR up to 8500 pounds) in the post-1985 period. Vehicle characteristics and weight re...

  15. Estimation and analysis of multifactor productivity in truck transportation : 1987 - 2003

    Science.gov (United States)

    2009-02-01

    The analysis has three objectives: 1) to estimate multifactor productivity (MFP) in truck transportation during 1987-2003; 2) to examine changes in multifactor productivity in U.S. truck transportation, over time, and to compare these changes to MFP ...

  16. Roadmap and technical white papers for the 21st century truck partnership

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2006-12-01

    21st Century Truck Partnership will support the development and implementation of technologies that will cut fuel use and emissions and enhance safety, affordability, and performance of trucks and buses.

  17. The impact of truck repositioning on congestion and pollution in the LA basin.

    Science.gov (United States)

    2011-03-01

    Pollution and congestion caused by port related truck traffic is usually estimated based on careful transportation modeling and simulation. In these efforts, however, attention is normally focused on trucks on their way from a terminal at the Los Ang...

  18. Long-Haul Truck Idling Burns Up Profits

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-08-12

    Long-haul truck drivers perform a vitally important service. In the course of their work, they must take rest periods as required by federal law. Most drivers remain in their trucks, which they keep running to provide power for heating, cooling, and other necessities. Such idling, however, comes at a cost; it is an expensive and polluting way to keep drivers safe and comfortable. Increasingly affordable alternatives to idling not only save money and reduce pollution, but also help drivers get a better night's rest.

  19. Impact of Platon ETC system on intercity trucking cost

    Directory of Open Access Journals (Sweden)

    Pogotovkina Natalya

    2017-01-01

    Full Text Available In 2015 Platon ETC System, a system of charging trucks with gross vehicle weight exceeding 12 tons, was implemented in Russia. The payment is collected as a compensation fo0 the damage caused to the federal public roads. Platon system is an additional source of financing for the road sector. However, its implementation made the carriers face the increasing costs. This paper presents the first results of the system functioning and the problems, associated with it. We consider the foreign systems of truck charging. The results of calculations, which show the effect of the toll collection on the prime cost of road freight transportation, are also presented.

  20. Whole-body Vibration Exposure Intervention among Professional Bus and Truck Drivers: A Laboratory Evaluation of Seat-suspension Designs.

    Science.gov (United States)

    Blood, Ryan P; Yost, Michael G; Camp, Janice E; Ching, Randal P

    2015-01-01

    Long-term exposure to seated whole-body vibration (WBV) is one of the leading risk factors for the development of low back disorders. Professional bus and truck drivers are regularly exposed to continuous WBV, since they spend the majority of their working hours driving heavy vehicles. This study measured WBV exposures among professional bus and truck drivers and evaluated the effects of seat-suspension designs using simulated field-collected data on a vibration table. WBV exposures were measured and compared across three different seat designs: an air-ride bus seat, an air-ride truck seat, and an electromagnetically active (EM-active) seat. Air-ride seats use a compressed-air bladder to attenuate vibrations, and they have been in operation throughout the transportation industry for many years. The EM-active seat is a relatively new design that incorporates a microprocessor-controlled actuator to dampen vibration. The vibration table simulated seven WBV exposure scenarios: four segments of vertical vibration and three scenarios that used field-collected driving data on different road surfaces-a city street, a freeway, and a section of rough roadway. The field scenarios used tri-axial WBV data that had been collected at the seat pan and at the driver's sternum, in accordance with ISO 2631-1 and 2631-5. This study found that WBV was significantly greater in the vertical direction (z-axis) than in the lateral directions (x-and y-axes) for each of the three road types and each of the three types of seats. Quantitative comparisons of the results showed that the floor-to-seat-pan transmissibility was significantly lower for the EM-active seat than for either the air-ride bus seat or the air-ride truck seat, across all three road types. This study also demonstrated that seat-suspension designs have a significant effect on the vibrations transmitted to vehicle operators, and the study's results may prove useful in designing future seat suspensions.

  1. Truck acceleration behavior study and acceleration lane length recommendations for metered on-ramps

    OpenAIRE

    Yang, Guangchuan; Xu, Hao; Wang, Zhongren; Tian, Zong

    2016-01-01

    This paper investigated the actual truck acceleration capability at metered on-ramps. Truck acceleration performance data were collected through a video-based data collection method. A piecewise constant acceleration model was employed to capture truck acceleration characteristics. It was found that the existing acceleration length will affect truck drivers’ acceleration behavior. At the taper type ramp that has limited acceleration distance, acceleration profile indicated a decreasing trend ...

  2. 77 FR 75257 - Proposed Collection of Information: Medium- and Heavy-Duty Truck Fleet Survey

    Science.gov (United States)

    2012-12-19

    ...-0170] Proposed Collection of Information: Medium- and Heavy-Duty Truck Fleet Survey AGENCY: National... collection of information will be in the form of a one-time survey of medium- and heavy-duty truck fleet... collection. OMB Control Number: To be issued at time of approval. Title: Medium- and Heavy-Duty Truck Fleet...

  3. The energy consumption and cost savings of truck electrification for heavy duty vocational applications

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Zhiming [ORNL; Lin, Zhenhong [ORNL; Franzese, Oscar [ORNL

    2017-01-01

    This paper evaluates the application of battery electric vehicles (BEVs) and genset plug-in hybrid electric vehicles (PHEVs) to Class-7 local delivery trucks and genset PHEV for Class-8 utility bucket trucks over widely real-world driving data performed by conventional heavy-duty trucks. A simulation tool based on vehicle tractive energy methodology and component efficiency for addressing component and system performance was developed to evaluate the energy consumption and performance of the trucks. As part of this analysis, various battery sizes combined with different charging powers on the E-Trucks for local delivery and utility bucket applications were investigated. The results show that the E-Truck applications not only reduce energy consumption but also achieve significant energy cost savings. For delivery E-Trucks, the results show that periodic stops at delivery sites provide sufficient time for battery charging, and for this reason, a high-power charger is not necessary. For utility bucket PHEV trucks, energy consumption per mile of bucket truck operation is typically higher because of longer idling times and extra high idling load associated with heavy utility work. The availability of on-route charging is typically lacking at the work sites of bucket trucks; hence, the battery size of these trucks is somewhat larger than that of the delivery trucks studied.

  4. Scheduling Trucks in a Cross-Dock with Mixed Service Mode Dock Doors

    DEFF Research Database (Denmark)

    Bodnar, Peter; Azadeh, Kaveh; Koster, René de

    2017-01-01

    The problem considered in this paper is how to schedule inbound and outbound trucks subject to time windows at a multidoor cross-dock. Dock doors can either be dedicated to inbound or outbound trucks or be capable of handling both truck types. In addition, loads are allowed to be temporarily buff...

  5. Planning of Truck Platoons: a Literature Review and Directions for Future Research

    NARCIS (Netherlands)

    A. Kishore Bhoopalam (Anirudh); N.A.H. Agatz (Niels); R.A. Zuidwijk (Rob)

    2017-01-01

    textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial

  6. 75 FR 56651 - ITS Joint Program Office; Trucking Industry Mobility & Technology Coalition Annual Meeting

    Science.gov (United States)

    2010-09-16

    ... DEPARTMENT OF TRANSPORTATION ITS Joint Program Office; Trucking Industry Mobility & Technology... Transportation. ACTION: Notice. The Trucking Industry Mobility & Technology Coalition (TIMTC) Annual [[Page 56652...: Beating Gridlock with a Smart Grid; U.S. DOT Truck Technology Initiatives; and State and Federal...

  7. 76 FR 22154 - Powered Industrial Trucks Standard; Extension of the Office of Management and Budget's (OMB...

    Science.gov (United States)

    2011-04-20

    ... instruction, practical training, and evaluation of the trainee's performance in the workplace. Paragraph (l)(3... truck(s) and workplace conditions. Paragraph (l)(6)--Certify that each operator meets the training and..., construction, and modification, as well as certification of training and evaluation for truck operators. DATES...

  8. 7 CFR 58.317 - Bulk butter trucks, boats, texturizers, and packers.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Bulk butter trucks, boats, texturizers, and packers... and Grading Service 1 Equipment and Utensils § 58.317 Bulk butter trucks, boats, texturizers, and packers. Bulk butter trucks, boats, texturizers, and packers shall be constructed of aluminum, stainless...

  9. Effects of Variation in Truck Factor on Pavement Performance in Pakistan

    Directory of Open Access Journals (Sweden)

    Rabia Chaudry

    2013-01-01

    Full Text Available Seasonal variation coupled with heavy axle loading is the key factor in rapid road deterioration in Pakistan. The serviceability loss is further accelerated by the fact that truck drivers and owners consider overloading as a profitable practice unaware of the adverse effects of this practice. Weigh-in-motion data from two stations located between two major cities of Pakistan (Peshawar and Rawalpindi on Grand Trunk Road (N-5 were collected and analyzed. Analysis of variance and comparison of actual and designed truck factor were performed to identify the most damaging axle truck type. It was found that axle truck type 3 (single/tandem axle is most damaging among all truck types. The actual truck factor for axle truck type 3 is 6.4 times greater than design truck factor. Regression expressions of different forms were also investigated to determine the relationship between truck factor and gross vehicular weight for the specified truck types. An optimum generalization strategy was used to prevent over-generalization and ensure accuracy. For data analysis, 75% of data was used to develop regression models and remaining 25% was to validate those models. The results show that the polynomial expressions performed best and provide a robust relationship that can be employed by the highway authorities to estimate truck factor from gross vehicular weight with a high degree of confidence. It was also observed that damaging effect of various types of trucks was very severe and quite high.

  10. 49 CFR 230.100 - Defects in tender truck axles and journals.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Defects in tender truck axles and journals. 230... Steam Locomotives and Tenders Running Gear § 230.100 Defects in tender truck axles and journals. (a... wheel seats that is more than 1/8 of an inch in depth. (b) Tender truck journal condemning defects...

  11. 76 FR 61138 - Pilot Program on NAFTA Long-Haul Trucking Provisions

    Science.gov (United States)

    2011-10-03

    ... (NAFTA) cross-border long-haul trucking provisions. This pilot program would allow Mexico-domiciled motor...-0097] Pilot Program on NAFTA Long-Haul Trucking Provisions AGENCY: Federal Motor Carrier Safety... implementation of its United States-Mexico cross- border long-haul trucking pilot program. FMCSA received five...

  12. Scenarios for Gluino Coannihilation

    CERN Document Server

    Ellis, John; Luo, Feng; Olive, Keith A

    2016-01-01

    We study supersymmetric scenarios in which the gluino is the next-to-lightest supersymmetric particle (NLSP), with a mass sufficiently close to that of the lightest supersymmetric particle (LSP) that gluino coannihilation becomes important. One of these scenarios is the MSSM with soft supersymmetry-breaking squark and slepton masses that are universal at an input GUT renormalization scale, but with non-universal gaugino masses. The other scenario is an extension of the MSSM to include vector-like supermultiplets. In both scenarios, we identify the regions of parameter space where gluino coannihilation is important, and discuss their relations to other regions of parameter space where other mechanisms bring the dark matter density into the range allowed by cosmology. In the case of the non-universal MSSM scenario, we find that the allowed range of parameter space is constrained by the requirement of electroweak symmetry breaking, the avoidance of a charged LSP and the measured mass of the Higgs boson, in parti...

  13. Regional climate change scenarios

    International Nuclear Information System (INIS)

    Somot, S.

    2005-01-01

    Because studies of the regional impact of climate change need higher spatial resolution than that obtained in standard global climate change scenarios, developing regional scenarios from models is a crucial goal for the climate modelling community. The zoom capacity of ARPEGE-Climat, the Meteo-France climate model, allows use of scenarios with a horizontal resolution of about 50 km over France and the Mediterranean basin. An IPCC-A2 scenario for the end of the 21. century in France shows higher temperatures in each season and more winter and less summer precipitation than now. Tuning the modelled statistical distributions to observed temperature and precipitation allows us to study changes in the frequency of extreme events between today's climate and that at the end of century. The frequency of very hot days in summer will increase. In particular, the frequency of days with a maximum temperature above 35 deg C will be multiplied by a factor of 10, on average. In our scenario, the Toulouse area and Provence might see one quarter of their summer days with a maximum temperature above 35 deg C. (author)

  14. Scenarios and innovative systems

    International Nuclear Information System (INIS)

    2001-11-01

    The purpose of this workshop is to present to the GEDEON community the scenarios for the deployment of innovative nuclear solutions. Both steady state situations and possible transitions from the present to new reactors and fuel cycles are considered. Innovative systems that satisfy improved natural resource utilization and waste minimization criteria will be described as well as the R and D orientations of various partners. This document brings together the transparencies of 17 communications given at this workshop: general policy for transmutation and partitioning; Amster: a molten salt reactor (MSR) concept; MSR capabilities; potentials and capabilities of accelerator driven systems (ADS); ADS demonstrator interest as an experimental facility; innovative systems: gas coolant technologies; Pu management in EPR; scenarios with thorium fuel; scenarios at the equilibrium state; scenarios for transition; partitioning and specific conditioning; management of separated radio-toxic elements; European programs; DOE/AAA (Advanced Accelerator Applications) program; OECD scenario studies; CEA research programs and orientations; partitioning and transmutation: an industrial point of view. (J.S.)

  15. Scenarios for gluino coannihilation

    Energy Technology Data Exchange (ETDEWEB)

    Ellis, John [Theoretical Particle Physics and Cosmology Group, Department of Physics, King’s College London, London, WC2R 2LS United Kingdom (United Kingdom); Theory Division, CERN,Geneva 23, CH-1211 (Switzerland); Evans, Jason L. [School of Physics and Astronomy, University of Minnesota,Minneapolis, MN, 55455 (United States); William I. Fine Theoretical Physics Institute, School of Physics and Astronomy, University of Minnesota, Minneapolis, MN, 55455 (United States); Luo, Feng [Theory Division, CERN,Geneva 23, CH-1211 (Switzerland); Olive, Keith A. [School of Physics and Astronomy, University of Minnesota,Minneapolis, MN, 55455 (United States); William I. Fine Theoretical Physics Institute, School of Physics and Astronomy, University of Minnesota, Minneapolis, MN, 55455 (United States)

    2016-02-11

    We study supersymmetric scenarios in which the gluino is the next-to-lightest supersymmetric particle (NLSP), with a mass sufficiently close to that of the lightest supersymmetric particle (LSP) that gluino coannihilation becomes important. One of these scenarios is the MSSM with soft supersymmetry-breaking squark and slepton masses that are universal at an input GUT renormalization scale, but with non-universal gaugino masses. The other scenario is an extension of the MSSM to include vector-like supermultiplets. In both scenarios, we identify the regions of parameter space where gluino coannihilation is important, and discuss their relations to other regions of parameter space where other mechanisms bring the dark matter density into the range allowed by cosmology. In the case of the non-universal MSSM scenario, we find that the allowed range of parameter space is constrained by the requirement of electroweak symmetry breaking, the avoidance of a charged LSP and the measured mass of the Higgs boson, in particular, as well as the appearance of other dark matter (co)annihilation processes. Nevertheless, LSP masses m{sub χ}≲8 TeV with the correct dark matter density are quite possible. In the case of pure gravity mediation with additional vector-like supermultiplets, changes to the anomaly-mediated gluino mass and the threshold effects associated with these states can make the gluino almost degenerate with the LSP, and we find a similar upper bound.

  16. Design and Validation Testing of TruckScan to Assay Large Sacks of Fukushima Radioactive Debris on a Truck

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Atsuo [Canberra-Japan (Japan); Bronson, Frazier [Canberra Industries Inc. (United States)

    2015-07-01

    As a result of the March 2011 earthquake and resulting tsunami in Japan, there was a serious accident at the Fukushima Dai-ichi Nuclear Power Plant. This accident has contaminated soil and vegetation in a wide area around the plant. Decontamination projects over the last 4 years have resulted in large numbers of 1 cubic meter canvas bags of debris, commonly called Super Sacks [SS]. These are currently stored nearby where they were generated, but starting in 2015, they will be moved to various Interim Storage Facilities [ISF]. Trucks will typically carry 8-20 of these SSs. When the trucks arrive at the ISF they need to be rapidly sorted into groups according to radioactivity level, for efficient subsequent processing. Canberra Industries, Inc. [CI] has designed a new truck monitoring system 'TruckScan' for use at these ISFs. The TruckScan system must measure the entire truck loaded with multiple closely packed SSs, and generate a nuclide specific assay report showing the radioactivity in each individual SS. The Canberra-Japan office, along with Obayashi Corporation have performed validation testing to demonstrate to the regulatory authorities that the proposed technique was sufficiently accurate. These validation tests were conducted at a temporary storage area in Fukushima prefecture. Decontaminated waste of various representative types and of various levels of radioactivity was gathered and mixed to create homogeneous volumes. These volumes were sampled multiple times and assayed with laboratory HPGe detectors to determine the reference concentration of each pile. Multiple SSs were loaded from each pile. Some of the SSs were filled 50% full, others 75% full, and others 100% full, to represent the typical loading configuration of the existing SSs in the field. The content of the SSs are either sand, soil, or vegetation with densities ranging from 0.3 g/cc - 1.6 g/cc. These SSs with known concentrations of Cs-134 and Cs-137 were then loaded onto trucks in

  17. Analysis of Truck Downtimes Using Log Dispersion Plot | Temeng ...

    African Journals Online (AJOL)

    This paper uses log dispersion plot to analyse downtimes of a fleet of 22 dump trucks from the. Nchanga Open Pit, Zambia over a period of two months. Downtimes were categorised into breakdown codes to determine which ones were acute, chronic or a combination of both. The breakdown codes which were critical to the ...

  18. Application of Proton Exchange Membrane Fuel Cell for Lift Trucks

    DEFF Research Database (Denmark)

    Hosseinzadeh, Elham; Rokni, Masoud

    2011-01-01

    in order to account for water back diffusion. Further Membrane water content is assumed to be a linear function of thickness. PEM fuel cell is working at rather low operating conditions which makes it suitable for the automotive systems. In this paper motive power part of a lift truck has been investigated...

  19. Work zone fatal crashes involving large trucks, 2012 : [analysis brief].

    Science.gov (United States)

    2014-11-01

    In 2012, 30,800 fatal crashes took place on our Nations roadways, with 11.2 percent (3,464) involving at least 1 large truck. While the majority of all fatal crashes (98.2 percent) took place outside of a work zone in 2012, 547 fatal crashes (1.8 ...

  20. 78 FR 24293 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-04-24

    ... CFR 390.5, and means an accident involving a commercial motor vehicle operating on a public road in... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  1. 78 FR 20373 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-04-04

    ... accident involving a commercial motor vehicle operating on a public road in interstate or intrastate... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No. FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  2. 78 FR 38431 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-06-26

    ... Safety Regulations-- General). N. Passed Phase 1, Factor 2: A ``yes'' in this column indicates the... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No. FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  3. 78 FR 25525 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-05-01

    ... (Federal Motor Carrier Safety Regulations-- General). N. Passed Phase 1, Factor 2: A ``yes'' in this column... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  4. 78 FR 67445 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-11-12

    ... Safety Regulations-- General). N. Passed Phase 1, Factor 2: A ``yes'' in this column indicates the... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  5. 77 FR 27837 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2012-05-11

    ... Motor Carrier Safety Regulations-- General). N. Passed Phase 1, Factor 2: A ``yes'' in this column... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  6. 78 FR 60010 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-09-30

    ... Motor Carrier Safety Regulations-- General). N. Passed Phase 1, Factor 2: A ``yes'' in this column... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  7. 77 FR 40938 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2012-07-11

    ... Safety Regulations-- General). N. Passed Phase 1, Factor 2: A ``yes'' in this column indicates the... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration...

  8. A Cognitive Analysis of Truck Drivers’ Right-hand Turns

    DEFF Research Database (Denmark)

    Sieker, Tobias Grønborg; G. Skulason, Thorgeir; Sletting, Kristian

    2015-01-01

    driving instructor is interviewed, and four truck drivers are observed and interviewed. This results in a cognitive work analysis with the phases work domain analysis, control task analysis and strategies analysis. Through this study it is indicated that many different types of information are sought...

  9. SVOC emissions from diesel trucks operating on biodiesel fuels

    Science.gov (United States)

    This study measured semivolatile organic compounds (SVOCs) in particle matter (PM) emitted from three heavy-duty trucks equipped with modern after-treatment technologies. Emissions testing was conducted as described by the George et al. VOC study also presented as part of this se...

  10. Analysis of frame structure of medium and small truck crane

    Science.gov (United States)

    Cao, Fuyi; Li, Jinlong; Cui, Mengkai

    2018-03-01

    Truck crane is an important part of hoisting machinery. Frame, as the support component of the quality of truck crane, determines the safety of crane jib load and the rationality of structural design. In this paper, the truck crane frame is a box structure, the three-dimensional model is established in CATIA software, and imported into Hyperworks software for finite element analysis. On the base of doing constraints and loads for the finite element model of the frame, the finite element static analysis is carried out. And the static stress test verifies whether the finite element model and the frame structure design are reasonable; then the free modal analysis of the frame and the analysis of the first 8 - order modal vibration deformation are carried out. The analysis results show that the maximum stress value of the frame is greater than the yield limit value of the material, and the low-order modal value is close to the excitation frequency value, which needs to be improved to provide theoretical reference for the structural design of the truck crane frame.

  11. U10 : Trusted Truck(R) II (phase B).

    Science.gov (United States)

    2009-01-01

    Phase B of the Trusted Truck II project built on the system developed in Phase A (or Year 1). For the implementation portion of the project, systems were added to the trailer to provide additional diagnostic trailer data that can be sent to the TTM...

  12. Presenting a conceptual pattern of HSE performance of oil trucks.

    Science.gov (United States)

    Ghaleh, Sahar; Omidvari, Manouchehr; Nassiri, Parvin; Momeni, Mansour; Lavasani, Seyed Mohammadreza Miri

    2018-01-25

    Accidents are among the main problems in the oil product supply chain. The most important effective factors in these events are the kind of trucks used and their health, safety, and environment (HSE) condition. The aim of this study was to present a conceptual pattern of the HSE performance of oil trucks in oil industries. In this study, 20 truck models (with fixed tanks), in use over different periods of time, were investigated. In this regard, the criteria and sub-criteria were first determined in two parts-carrier and tank-and weighted by fuzzy analytical hierarchy process (FAHP). The results showed that the most important sub-criteria regarding the HSE factors of the carrier were resistance and strength of the front and rear shields, the brake system, and the ventilation system. The most important sub-criteria regarding the HSE factors of the tank were tank shell thickness and a good tank design shape with respect to portable material. It should be noted that the weight of the criteria with each other and sub-criteria with each other are not equal. This issue is important for decision-making. The main reason for the use of trucks with the lowest score in developing countries is the lack of attention by managers to safety issues and international standards and agreements such as the ADR.

  13. Individual Differences in Boredom Proneness amongst Truck Drivers ...

    African Journals Online (AJOL)

    esteem and locus of control individually and jointly predicted boredom proneness amongst truck drivers. The same variables jointly accounted for 67% of the proportion of the variance in boredom proneness. Results of the 2 x 2 x 2 ANOVA also ...

  14. 78 FR 26106 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-05-03

    ... DEPARTMENT OF TRANSPORTATION Federal Motor Carrier Safety Administration [Docket No FMCSA-2011-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration (FMCSA). ACTION: Notice; correction. SUMMARY: The FMCSA published a document in the Federal Register of...

  15. 76 FR 56272 - Pilot Project on NAFTA Trucking Provisions

    Science.gov (United States)

    2011-09-12

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... ability of Mexico- domiciled motor carriers to operate safely in the United States beyond the municipalities in the United States on the United States-Mexico international border or the commercial zones of...

  16. 76 FR 56868 - Pilot Project on NAFTA Trucking Provisions

    Science.gov (United States)

    2011-09-14

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... ability of Mexico- domiciled motor carriers to operate safely in the United States beyond the municipalities in the United States on the United States-Mexico international border or the commercial zones of...

  17. 77 FR 12356 - Pilot Program on NAFTA Trucking Provisions

    Science.gov (United States)

    2012-02-29

    ...-0097] Pilot Program on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... of Mexico-domiciled motor carriers to operate safely in the United States beyond the municipalities in the United States on the United States-Mexico international border or the commercial zones of such...

  18. 78 FR 11728 - Pilot Project on NAFTA Trucking Provisions

    Science.gov (United States)

    2013-02-19

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... or expending appropriated funds to grant authority to Mexico-domiciled motor carriers to operate beyond the municipalities in the United States on the United States-Mexico international border or the...

  19. 76 FR 73765 - Pilot Project on NAFTA Trucking Provisions

    Science.gov (United States)

    2011-11-29

    ...-0097] Pilot Project on NAFTA Trucking Provisions AGENCY: Federal Motor Carrier Safety Administration... ability of Mexico- domiciled motor carriers to operate safely in the United States beyond the municipalities in the United States on the United States-Mexico international border or the commercial zones of...

  20. Parts Counterperson. Auto, Agriculture & Truck. Task List Competency Record.

    Science.gov (United States)

    Minnesota Instructional Materials Center, White Bear Lake.

    Developed by industry representatives and educators for use by vocational instructors, this guide focuses on the tasks and competencies necessary for a student to develop in order to secure employment as a counterperson in automobile, agriculture, and truck parts. The task list is an outline of various skills and proficiencies and covers sales,…

  1. Scenario-based strategizing

    DEFF Research Database (Denmark)

    Lehr, Thomas; Lorenz, Ullrich; Willert, Markus

    2017-01-01

    on behavioural strategy as a theoretical lens, we design a yardstick to study the impact of scenario-based strategizing. We then describe our approach, which includes developing scenarios and alternative strategies separately and supporting the strategy selection through an integrated assessment of the goal......-based efficacy and robustness. To facilitate the colla- borative strategizing in teams, we propose a matrix with robustness and efficacy as the two axes, which we call the Parmenides Matrix. We assess the impact of the novel approach by applying it in two cases, at a govern- mental agency (German Environmental...... Ministry) and a firm affected by disruptive change (Bosch, leading global supplier of technology and solutions)....

  2. The Scenario Planning Paradox

    DEFF Research Database (Denmark)

    Spaniol, Matthew Jon; Rowland, Nicholas James

    2017-01-01

    For more than a decade, futures studies scholars have prefaced scholarly contributions by repeating the claim that there is insufficient theory to support chaotic scenario methodology. The strategy is formulaic, and the net effect is a curious one, which the authors refer to as the scenario......, which motivates re-statement of the claim in the first place, ultimately fails. In actuality, the field is distanced from its purported goals. The “dismal” state of theory encourages scholars to adopt theory that is not necessarily tethered to a common core, which does not contribute to a shared...

  3. Evaluating sustainability of truck weight regulations: A system dynamics view

    Directory of Open Access Journals (Sweden)

    Pei Liu

    2015-11-01

    Full Text Available Purpose: Targeting the problem of overload trucking in Highway Transportation of iron ore from Caofeidian to Tangshan (HTCT, this paper aims to assess long-term effects of alternative Truck Weight Regulation (TWR policies on sustainability of HTCT. Design/methodology/approach: A system dynamics model was established for policy evaluation. The model, composed of six interrelating modules, is able to simulate policies effects on trucking issues such as freight flow, truck traffic flow, pavement performance, highway transport capacity and trucking time, and further on the Cumulative Economic Cost (CEC including transport cost and time cost of freight owners and the Cumulative Social Cost (CSC including pavement maintenance cost, green house gas emission cost, air pollutants emission cost and traffic accidents cost, so the effects of TWR policies on sustainability of HTCT could be evaluated. Findings: According to different values of overload ratio which a TWR policy allows, alternative TWR policies are classified into three types, which are The Rigid Policy (TRP, The Moderate Policy (TMP and The Tolerant Policy (TTP. Results show that the best policy for sustainability of HTCT depends on the importance of CSC which is expected by the local government. To be specific, (1 if CSC is considered much less important than CEC, the local government should continue implementing the current TTP with the maximum overload ratio; (2 if CSC is considered much more important than CEC, then TRP is recommended; and (3 if CSC is considered slightly more important than CES, TMP with overload ratio of 80% is the best. Practical implications: Conclusions of this paper may help the local government design appropriate TWR policies to achieve sustainability of HTCT. Originality/value: To the best of our knowledge, this is the first effort to evaluate TWR policies on sustainability of regional freight transportation based on system dynamics modeling.

  4. Six Reasons why hours of service regulations for truck drivers are violated

    DEFF Research Database (Denmark)

    Grøn, Sisse

    2008-01-01

      ABSTRACT Two decades of research has established a correlation between tiredness and fatigue, and traffic accident involving truck drivers.  Regulations limiting the driving hours of truck drivers thus are necessary precautions. But compliance is a problem. The answer from authorities tend......, because a truck driver's work is unpredictable and independent, but the regulation is action-defining and inflexible. Thus the regulations provoke violations because they counteract with the reality of truck drivers´ work conditions. The fifth reason is that the regulation counteracts with a general...... independency ideal among truck drivers. The last reason is that the drivers and their employers share an interest in long work hours....

  5. Emergency exercise scenario tools

    International Nuclear Information System (INIS)

    Sjoeblom, K.

    1998-03-01

    Nuclear power plant emergency exercises require a realistically presented accident situation which includes various aspects: plant process, radioactivity, radiation, weather and people. Experiences from nuclear power plant emergency exercises show that preparing accident scenarios even for relatively short exercises is tedious. In the future modern computer technology and past experience could be used for making exercise planning more effective. (au)

  6. Crisis and Crisis Scenarios

    DEFF Research Database (Denmark)

    Larsen, Øjvind

    2016-01-01

    This special issue of Nordicum-Mediterraneum contains select proceedings from the third meeting of the Nordic Summer University research circle called “Crisis and Crisis Scenarios: Normativity, Possibilities and Dilemmas”, held April 9th — 12th, 2015 at the Lysebu Conference Centre in Oslo, Norway...

  7. An economically reliable scenario

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    Mister Benjamin Dessus, director of the Ecotech programme at the Cnrs and author of the Noe scenario, describes his propositions for energy prospective, supported by an economic analysis. He advocates the energy diversification and the use of renewable energies. (N.C.). 1 ref., 1 tab

  8. Idle emissions from medium heavy-duty diesel and gasoline trucks.

    Science.gov (United States)

    Khan, A B M S; Clark, Nigel N; Gautam, Mridul; Wayne, W Scott; Thompson, Gregory J; Lyons, Donald W

    2009-03-01

    Idle emissions data from 19 medium heavy-duty diesel and gasoline trucks are presented in this paper. Emissions from these trucks were characterized using full-flow exhaust dilution as part of the Coordinating Research Council (CRC) Project E-55/59. Idle emissions data were not available from dedicated measurements, but were extracted from the continuous emissions data on the low-speed transient mode of the medium heavy-duty truck (MHDTLO) cycle. The four gasoline trucks produced very low oxides of nitrogen (NOx) and negligible particulate matter (PM) during idle. However, carbon monoxide (CO) and hydrocarbons (HCs) from these four trucks were approximately 285 and 153 g/hr on average, respectively. The gasoline trucks consumed substantially more fuel at an hourly rate (0.84 gal/hr) than their diesel counterparts (0.44 gal/hr) during idling. The diesel trucks, on the other hand, emitted higher NOx (79 g/hr) and comparatively higher PM (4.1 g/hr), on average, than the gasoline trucks (3.8 g/hr of NOx and 0.9 g/hr of PM, on average). Idle NOx emissions from diesel trucks were high for post-1992 model year engines, but no trends were observed for fuel consumption. Idle emissions and fuel consumption from the medium heavy-duty diesel trucks (MHDDTs) were marginally lower than those from the heavy heavy-duty diesel trucks (HHDDTs), previously reported in the literature.

  9. Managing truck arrivals with time windows to alleviate gate congestion at container terminals

    DEFF Research Database (Denmark)

    Chen, G.; Govindan, Kannan; Yang, Z.

    2013-01-01

    Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries into gro......Long truck queues at gates often limit the efficiency of a container terminal and generate serious air pollution. To reduce the gate congestion, this paper proposes a method called'vessel dependent time windows (VDTWs)' to control truck arrivals, which involves partitioning truck entries...... in the system. A conventional Genetic Algorithm (GA), a multi-society GA, and a hybrid algorithm using GA and Simulated Annealing are used to solve the optimization problem. A case study based on a real container terminal in China is performed, which shows the VDTWs method can flatten the truck arrivals...

  10. Plug-In Hybrid Urban Delivery Truck Technology Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Miyasato, Matt [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Impllitti, Joseph [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Pascal, Amar [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States)

    2015-07-31

    The I-710 and CA-60 highways are key transportation corridors in the Southern California region that are heavily used on a daily basis by heavy duty drayage trucks that transport the cargo from the ports to the inland transportation terminals. These terminals, which include store/warehouses, inland-railways, are anywhere from 5 to 50 miles in distance from the ports. The concentrated operation of these drayage vehicles in these corridors has had and will continue to have a significant impact on the air quality in this region whereby significantly impacting the quality of life in the communities surrounding these corridors. To reduce these negative impacts it is critical that zero and near-zero emission technologies be developed and deployed in the region. A potential local market size of up to 46,000 trucks exists in the South Coast Air Basin, based on near- dock drayage trucks and trucks operating on the I-710 freeway. The South Coast Air Quality Management District (SCAQMD), California Air Resources Board (CARB) and Southern California Association of Governments (SCAG) — the agencies responsible for preparing the State Implementation Plan required under the federal Clean Air Act — have stated that to attain federal air quality standards the region will need to transition to broad use of zero and near zero emission energy sources in cars, trucks and other equipment (Southern California Association of Governments et al, 2011). SCAQMD partnered with Volvo Trucks to develop, build and demonstrate a prototype Class 8 heavy-duty plug-in hybrid drayage truck with significantly reduced emissions and fuel use. Volvo’s approach leveraged the group’s global knowledge and experience in designing and deploying electromobility products. The proprietary hybrid driveline selected for this proof of concept was integrated with multiple enhancements to the complete vehicle in order to maximize the emission and energy impact of electrification. A detailed review of all

  11. Hanford groundwater scenario studies

    International Nuclear Information System (INIS)

    Arnett, R.C.; Gephart, R.E.; Deju, R.A.; Cole, C.R.; Ahlstrom, S.W.

    1977-05-01

    This report documents the results of two Hanford groundwater scenario studies. The first study examines the hydrologic impact of increased groundwater recharge resulting from agricultural development in the Cold Creek Valley located west of the Hanford Reservation. The second study involves recovering liquid radioactive waste which has leaked into the groundwater flow system from a hypothetical buried tank containing high-level radioactive waste. The predictive and control capacity of the onsite Hanford modeling technology is used to evaluate both scenarios. The results of the first study indicate that Cold Creek Valley irrigationis unlikely to cause significant changes in the water table underlying the high-level waste areas or in the movement of radionuclides already in the groundwater. The hypothetical tank leak study showed that an active response (in this case waste recovery) can be modeled and is a possible alternative to passive monitoring of radionuclide movement in the unlikely event that high-level waste is introduced into the groundwater

  12. Demand scenarios, worldwide

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, A. [Massachusetts Inst. of Technology, Center for Technology, Policy and Industrial Development and the MIT Joint Program on the Science and Policy of Global Change, Cambridge, MA (United States)

    1996-11-01

    Existing methods are inadequate for developing aggregate (regional and global) and long-term (several decades) passenger transport demand scenarios, since they are mainly based on simple extensions of current patterns rather than causal relationships that account for the competition among transport modes (aircraft, automobiles, buses and trains) to provide transport services. The demand scenario presented in this paper is based on two empirically proven invariances of human behavior. First, transport accounts for 10 to 15 percent of household total expenditures for those owning an automobile, and around 5 percent for non-motorized households on average (travel money budget). Second, the mean time spent traveling is approximately one hour per capita per day (travel time budget). These two budgets constraints determine the dynamics of the scenario: rising income increases per capita expenditure on travel which, in turn, increase demand for mobility. Limited travel time constraints travelers to shift to faster transport systems. The scenario is initiated with the first integrated historical data set on traffic volume in 11 world regions and the globe from 1960 to 1990 for all major modes of motorized transport. World average per capita traffic volume, which was 1,800 kilometers in 1960 and 4,2090 in 1990, is estimated to rise to 7,900 kilometers in 2020 - given a modest average increase in Gross World Product of 1.9% per year. Higher economic growth rates in Asian regions result in an increase in regional per capita traffic volume up to a factor of 5.3 from 1990 levels. Modal splits continue shifting to more flexible and faster modes of transport. At one point, passenger cars can no longer satisfy the increasing demand for speed (i.e. rising mobility within a fixed time budget). In North America it is estimated that the absolute traffic volume of automobiles will gradually decline starting in the 2010s. (author) 13 figs., 6 tabs., 35 refs.

  13. Ontario demand response scenarios

    International Nuclear Information System (INIS)

    Rowlands, I.H.

    2005-09-01

    Strategies for demand management in Ontario were examined via 2 scenarios for a commercial/institutional building with a normal summertime peak load of 300 kW between 14:00 and 18:00 during a period of high electricity demand and high electricity prices. The first scenario involved the deployment of a 150 kW on-site generator fuelled by either diesel or natural gas. The second scenario involved curtailing load by 60 kW during the same periods. Costs and benefits of both scenarios were evaluated for 3 groups: consumers, system operators and society. Benefits included electricity cost savings, deferred transmission capacity development, lower system prices for electricity, as well as environmental changes, economic development, and a greater sense of corporate social responsibility. It was noted that while significant benefits were observed for all 3 groups, they were not substantial enough to encourage action, as the savings arising from deferred generation capacity development do not accrue to individual players. The largest potential benefit was identified as lower prices, spread across all users of electricity in Ontario. It was recommended that representative bodies cooperate so that the system-wide benefits can be reaped. It was noted that if 10 municipal utilities were able to have 250 commercial or institutional customers engaged in distributed response, then a total peak demand reduction of 375 MW could be achieved, representing more than 25 per cent of Ontario's target for energy conservation. It was concluded that demand response often involves the investment of capital and new on-site procedures, which may affect reactions to various incentives. 78 refs., 10 tabs., 5 figs

  14. Domestic Energy Scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Aabakken, J.; Short, W.

    2003-01-01

    This report attempts to organize and evaluate scenarios of markets and technologies that could impact renewable and distributed electricity-generating technologies during the next 20-100 years in the United States. For the purposes of this report, scenarios are defined broadly as any projection or forecast that helps illuminate the potential of Renewable Electric Technologies (RETs) in the United States. Scenarios vary widely in terms of their scope-some focus on supply of fuels or narrow segments of markets with limited timeframes, while others are broader in scope and time span. There are several factors that influence the market penetration of renewable energy and distributed generation technologies. Most notable among these are natural gas prices, technology improvements, and policy measures. Natural gas prices are important because most new generating capacity, as well as marginal generation units, generally are natural-gas fired. Assumptions about the rate of improvement in renewable and distributed generation technologies can also have a significant impact on market penetration. Finally, policy measures that support these technologies, such as tax credits or interconnection standards, can contribute to their accelerated adoption.

  15. Cummins L10G in Kenworth truck 'viable today'

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    As the culmination of five years of developmental work by Cummins Engines, BC Research Inc., and BC Gas Utility Ltd., a T800 Kenworth truck was outfitted with a new Cummins L10G natural gas engine, and two lightweight fully -wrapped Dynetek cylinders; it was pronounced to be 'a viable clean truck today'. The L10G spark-ignited engine operates at a relatively high peak efficiency of 37 per cent and is commercially available to meet the current California Air Resources Board heavy duty vehicle emission standards without the use of a catalytic converter. The L10G engine produces no particulate emissions, a very significant advantage, in view of the fact that particulate emissions have been identified as major contributors to respiratory ailments

  16. Optimization of Front Axle Suspension System of Articulated Dump Truck

    DEFF Research Database (Denmark)

    Langer, Thomas Heegaard; Christensen, Brian B.; Mouritsen, Ole Ø.

    2010-01-01

    Manufacturers of construction machinery are challenged to accommodate legal requirements on the vibration exposure associated with their products. For such machines a crucial performance parameter is the whole body vibration level that the operator is subjected to. This paper presents results from...... that has been subjected to comfort improvement is a two axle articulated dump truck. The comfort has been in terms of whole body vibration exposure and the overall improvement has been made possible by adding front axle suspension. However, a hydraulic stabilizing system between the tractor and trailer...... to evaluate the whole body vibrations. By use of a multibody simulation model of the dump truck the whole body vibration exposure has been computed using the predefined work cycle as model input. The design parameters comprise the components of the hydraulic subsystem of the suspension, i.e., the size...

  17. Antecedents of Truck Drivers’ Job Satisfaction and Retention Proneness

    DEFF Research Database (Denmark)

    Prockl, Günter; Teller, Christoph; Kotzab, Herbert

    2017-01-01

    The aim of this study was to (1) explore the antecedents of truck drivers’ job satisfaction, (2) identify the impact of financial and nonfinancial job properties on satisfaction with the job and with one's employer, and (3) the drivers’ proneness to retaining their jobs. Based on the extant...... literature, we develop a conceptual model that is tested using survey data for 164 truck drivers. Multiple linear and ordinal logistic regressions were used to estimate the proposed effects. The results reveal that nonfinancial job properties and satisfaction with one's employer affect job satisfaction...... is statistically significant. Financial and nonfinancial job properties affect satisfaction with one's employer whereas the former shows a lower impact compared to the latter. Satisfaction with the job and one's employer impacts retention proneness. The contribution of this study was to (1) add...

  18. Fuel Cell-Powered Lift Truck Fleet Deployment Projects Final Technical Report May 2014

    Energy Technology Data Exchange (ETDEWEB)

    Klingler, James J [GENCO Infrastructure Solutions, Inc.

    2014-05-06

    The overall objectives of this project were to evaluate the performance, operability and safety of fork lift trucks powered by fuel cells in large distribution centers. This was accomplished by replacing the batteries in over 350 lift trucks with fuel cells at five distribution centers operated by GENCO. The annual cost savings of lift trucks powered by fuel cell power units was between $2,400 and $5,300 per truck compared to battery powered lift trucks, excluding DOE contributions. The greatest savings were in fueling labor costs where a fuel cell powered lift truck could be fueled in a few minutes per day compared to over an hour for battery powered lift trucks which required removal and replacement of batteries. Lift truck operators where generally very satisfied with the performance of the fuel cell power units, primarily because there was no reduction in power over the duration of a shift as experienced with battery powered lift trucks. The operators also appreciated the fast and easy fueling compared to the effort and potential risk of injury associated with switching heavy batteries in and out of lift trucks. There were no safety issues with the fueling or operation of the fuel cells. Although maintenance costs for the fuel cells were higher than for batteries, these costs are expected to decrease significantly in the next generation of fuel cells, making them even more cost effective.

  19. On Relations Between Dump Truck Efficiency and Service Facilities Structure

    OpenAIRE

    Savchenko, A.A.; Zubariev, M.S.

    2015-01-01

    International audience; The analysis of dump truck fleet of the open-pit mine, which possesses industrial real estates for technical maintenance and other operations, is provided. Several exploitation indexes are defined and analyzed subject to the corresponding mine. Basing on the provided analysis, factors and conditions, which define the production facility structure, are described. A list of production facility structures is provided. The influence of production facility structure on dump...

  20. FATIGUE WELDING JOINT RESISTANCE OF MINING DUMP TRUCK BEARING CONSTRUCTIONS

    Directory of Open Access Journals (Sweden)

    A. A. Rakitsky

    2010-01-01

    Full Text Available The paper investigates a possibility to apply European norms on designing of welded constructions for frames of heavy-load mining dump trucks. Comparison of results concerning tests of welding joint specimen made of local steel with recommended standards of fatigue curves is executed in the paper. The paper reveals that while forecasting resource of automotive constructions with the accepted practical accuracy it is possible to use generalized fatigue resistance characteristics of standard welding joints. 

  1. 21st Century Truck Partnership 2013 Fall Meeting Summary Report

    Science.gov (United States)

    2014-01-14

    Weighting & Vehicle System Design) − Industry Lead: Mr. Skip Yeakel, Volvo Trucks North America The Down-select Consolidation Session consisted...Efficiency, Light- Weighting & Vehicle System Design  Mr. Sam McLaughlin, Manager, Volvo External Research North America Region with Mr. Skip Yeakel...Principal Engineer, Volvo Advanced Engineering − Vehicle Fuel Efficiency  Dr. Vivek Sujan, Technical Advisor – Advanced Systems Integration

  2. Hydraulic Hybrid Parcel Delivery Truck Deployment, Testing & Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Gallo, Jean-Baptiste [Calstart Incorporated, Pasadena, CA (United States)

    2014-03-07

    Although hydraulic hybrid systems have shown promise over the last few years, commercial deployment of these systems has primarily been limited to Class 8 refuse trucks. In 2005, the Hybrid Truck Users Forum initiated the Parcel Delivery Working Group including the largest parcel delivery fleets in North America. The goal of the working group was to evaluate and accelerate commercialization of hydraulic hybrid technology for parcel delivery vehicles. FedEx Ground, Purolator and United Parcel Service (UPS) took delivery of the world’s first commercially available hydraulic hybrid parcel delivery trucks in early 2012. The vehicle chassis includes a Parker Hannifin hydraulic hybrid drive system, integrated and assembled by Freightliner Custom Chassis Corp., with a body installed by Morgan Olson. With funding from the U.S. Department of Energy, CALSTART and its project partners assessed the performance, reliability, maintainability and fleet acceptance of three pre-production Class 6 hydraulic hybrid parcel delivery vehicles using information and data from in-use data collection and on-road testing. This document reports on the deployment of these vehicles operated by FedEx Ground, Purolator and UPS. The results presented provide a comprehensive overview of the performance of commercial hydraulic hybrid vehicles in parcel delivery applications. This project also informs fleets and manufacturers on the overall performance of hydraulic hybrid vehicles, provides insights on how the technology can be both improved and more effectively used. The key findings and recommendations of this project fall into four major categories: -Performance, -Fleet deployment, -Maintenance, -Business case. Hydraulic hybrid technology is relatively new to the market, as commercial vehicles have been introduced only in the past few years in refuse and parcel delivery applications. Successful demonstration could pave the way for additional purchases of hydraulic hybrid vehicles throughout the

  3. The ethanol heavy-duty truck fleet demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-06-01

    This project was designed to test and demonstrate the use of a high- percentage ethanol-blended fuel in a fleet of heavy-duty, over-the- road trucks, paying particular attention to emissions, performance, and repair and maintenance costs. This project also represents the first public demonstration of the use of ethanol fuels as a viable alternative to conventional diesel fuel in heavy-duty engines.

  4. Definition and Evaluation of Bus and Truck Automation Operations Concepts

    OpenAIRE

    Tsao, H.-S. Jacob; Botha, Jan L.

    2002-01-01

    Traffic congestion will continue to worsen and likely worsen at a faster rate than ever. People throughput and freight throughput have become critical issues for California and the rest of the nation. PATH has been funding a one-year research project entitled "Definition and Evaluation of Bus and Truck Automation Operations Concepts," proposed by the authors. This report summarizes the results of the research project achieved during the first six months. During those six months, we reviewed l...

  5. Factors influencing injury severity of crashes involving HAZMAT trucks

    Directory of Open Access Journals (Sweden)

    Majbah Uddin

    2018-03-01

    Full Text Available This paper investigates factors affecting injury severity of crashes involving HAZMAT large trucks. It uses the crash data in the state of California from the Highway Safety Information System, from 2005 to 2011. The explanatory factors include the occupant, crash, vehicle, roadway, environmental, and temporal characteristics. Both fixed- and random-parameters ordered probit models of injury severity (where possible outcomes are major, minor, and no injury were estimated; the random-parameters model captures possible unobserved effects related to factors not present in the data. The model results indicate that the occupants being male, truck drivers, crashes occurring in rural locations, under dark-unlighted, under dark-lighted conditions, and on weekdays were associated with increased probability of major injuries. Conversely, the older occupants (age 60 and over, truck making a turn, rear-end collision, collision with an object, crashes occurring on non-interstate highway, higher speed limit highway (≥65 mph, and flat terrain were associated with decreased probability of major injuries. This study has identified factors that explain injury severities of crashes involving HAZMAT, and as such, it could be used by policy makers and transportation agencies to improve HAZMAT transport, and thus, the overall highway safety.

  6. Upgrades for truck transportation of SNM in the Russian Federation

    International Nuclear Information System (INIS)

    Gardner, B.H.; Kornilovich, E.

    1998-01-01

    The goal of this project is the rapid reduction of risk to truck transportation of SNM in Russia. Enhanced protection is being accomplished by cooperation between the US Department of Energy, MINATOM of Russia, the Russian Ministry of Defense, and various Russian Institutes. This program provides an integrated program of specialized trucks that are equipped with hardened overpack (SNM vault) containers, alarm and communications systems, and armored cabs. Armored escort vehicles are also provided to increase the survivability of the guards escorting convoys. Only indigenous Russian equipment, modified and/or manufactured by Designing Bureau for Motor Vehicle Transport Equipment (KBATO), is provided under this program. The US will not provide assistance in the truck transportation arena without a commitment from the Russian facility to provide heavily armed escorts for SNM movement. Each site conducts a detailed transportation needs assessment study that is used as the basis for prioritizing assistance. The Siberian Chemical Combine (Tomsk-7) was the initial site of cooperation. The designs used at Tomsk-7 are serving as the baseline for all future vehicles modified under this program. In FY98, many vehicles systems have been ordered for various institutes. Many additional systems will be ordered in FY99

  7. Scenarios for the future

    International Nuclear Information System (INIS)

    Haegermark, H.; Bergmark, M.

    1995-06-01

    This project aims primarily to give a basis for the joint R and D program for the Swedish electric utility industry, in the form of pictures of the future up to 2020. The work was performed during four seminars in a group of managers and R and D planners. The four scenarios differ mainly in the assumptions of high or low economic growth and on market or political rule. Assumptions on essential uncertainties about the future have been combined in a consistent manner, e.g. on the structure of the utility industry, the role of nuclear power, the importance of the greenhouse gas issue, the influence of new technology developments and on changes of values in society. Certain other development appear in all scenarios, e.g. the impact of information technology throughout society, the internationalization of business in general and industrial production in particular, considerations for the environment and care for natural resources. The four scenarios are: 'Technology on the throne' (market rule/high growth); 'Intense competition' (market rule/low growth); 'Monopoly takes over' (political rule/high growth); and 'Green local society' (political rule/low growth). Some of the important factors pointed out by the study are: Increased customer mobility between regions and countries; The impact of information technology; Societal value changes; Sustainable development as an important driving force; Structure of the utility industry. Diversifying into new services. New players; Access to knowledge and competence; Ways for handling the greenhouse gas problem; Preparedness for nuclear power phase-out. 12 figs, 6 tabs

  8. Developing high-resolution urban scale heavy-duty truck emission inventory using the data-driven truck activity model output

    Science.gov (United States)

    Perugu, Harikishan; Wei, Heng; Yao, Zhuo

    2017-04-01

    Air quality modelers often rely on regional travel demand models to estimate the vehicle activity data for emission models, however, most of the current travel demand models can only output reliable person travel activity rather than goods/service specific travel activity. This paper presents the successful application of data-driven, Spatial Regression and output optimization Truck model (SPARE-Truck) to develop truck-related activity inputs for the mobile emission model, and eventually to produce truck specific gridded emissions. To validate the proposed methodology, the Cincinnati metropolitan area in United States was selected as a case study site. From the results, it is found that the truck miles traveled predicted using traditional methods tend to underestimate - overall 32% less than proposed model- truck miles traveled. The coefficient of determination values for different truck types range between 0.82 and 0.97, except the motor homes which showed least model fit with 0.51. Consequently, the emission inventories calculated from the traditional methods were also underestimated i.e. -37% for NOx, -35% for SO2, -43% for VOC, -43% for BC, -47% for OC and - 49% for PM2.5. Further, the proposed method also predicted within ∼7% of the national emission inventory for all pollutants. The bottom-up gridding methodology used in this paper could allocate the emissions to grid cell where more truck activity is expected, and it is verified against regional land-use data. Most importantly, using proposed method it is easy to segregate gridded emission inventory by truck type, which is of particular interest for decision makers, since currently there is no reliable method to test different truck-category specific travel-demand management strategies for air pollution control.

  9. Scheduling trucks in cross docking systems with temporary storage and dock repeat truck holding pattern using genetic algorithm

    Directory of Open Access Journals (Sweden)

    Ehsan Ghobadian

    2013-02-01

    Full Text Available Cross docking is one of the most important issues in management of supply chains. In cross docking, different items delivered to a warehouse by inbound trucks are directly arranged and reorganized based on customer demands, routed and loaded into outbound trucks for delivery purposes to customers without virtually keeping them at the warehouse. If any item is kept in storage, it is normally for a short amount of time, say less than 24 hours. In this paper, we consider a special case of cross docking where there is temporary storage and implements genetic algorithm to solve the resulted problem for some realistic test problems. In our method, we first use some heuristics as initial solutions and then improve the final solution using genetic algorithm. The performance of the proposed model is compared with alternative solution strategy, the GRASP method.

  10. Evolving practices in environmental scenarios: a new scenario typology

    Science.gov (United States)

    Wilkinson, Angela; Eidinow, Esther

    2008-10-01

    A new approach to scenarios focused on environmental concerns, changes and challenges, i.e. so-called 'environmental scenarios', is necessary if global environmental changes are to be more effectively appreciated and addressed through sustained and collaborative action. On the basis of a comparison of previous approaches to global environmental scenarios and a review of existing scenario typologies, we propose a new scenario typology to help guide scenario-based interventions. This typology makes explicit the types of and/or the approaches to knowledge ('the epistemologies') which underpin a scenario approach. Drawing on previous environmental scenario projects, we distinguish and describe two main types in this new typology: 'problem-focused' and 'actor-centric'. This leads in turn to our suggestion for a third type, which we call 'RIMA'—'reflexive interventionist or multi-agent based'. This approach to scenarios emphasizes the importance of the involvement of different epistemologies in a scenario-based process of action learning in the public interest. We suggest that, by combining the epistemologies apparent in the previous two types, this approach can create a more effective bridge between longer-term thinking and more immediate actions. Our description is aimed at scenario practitioners in general, as well as those who work with (environmental) scenarios that address global challenges.

  11. Evolving practices in environmental scenarios: a new scenario typology

    Energy Technology Data Exchange (ETDEWEB)

    Wilkinson, Angela; Eidinow, Esther [James Martin Institute, Said Business School, University of Oxford, Park End Street, Oxford OX1 1HP (United Kingdom)

    2008-10-15

    A new approach to scenarios focused on environmental concerns, changes and challenges, i.e. so-called 'environmental scenarios', is necessary if global environmental changes are to be more effectively appreciated and addressed through sustained and collaborative action. On the basis of a comparison of previous approaches to global environmental scenarios and a review of existing scenario typologies, we propose a new scenario typology to help guide scenario-based interventions. This typology makes explicit the types of and/or the approaches to knowledge ('the epistemologies') which underpin a scenario approach. Drawing on previous environmental scenario projects, we distinguish and describe two main types in this new typology: 'problem-focused' and 'actor-centric'. This leads in turn to our suggestion for a third type, which we call 'RIMA'-'reflexive interventionist or multi-agent based'. This approach to scenarios emphasizes the importance of the involvement of different epistemologies in a scenario-based process of action learning in the public interest. We suggest that, by combining the epistemologies apparent in the previous two types, this approach can create a more effective bridge between longer-term thinking and more immediate actions. Our description is aimed at scenario practitioners in general, as well as those who work with (environmental) scenarios that address global challenges.

  12. Evolving practices in environmental scenarios: a new scenario typology

    International Nuclear Information System (INIS)

    Wilkinson, Angela; Eidinow, Esther

    2008-01-01

    A new approach to scenarios focused on environmental concerns, changes and challenges, i.e. so-called 'environmental scenarios', is necessary if global environmental changes are to be more effectively appreciated and addressed through sustained and collaborative action. On the basis of a comparison of previous approaches to global environmental scenarios and a review of existing scenario typologies, we propose a new scenario typology to help guide scenario-based interventions. This typology makes explicit the types of and/or the approaches to knowledge ('the epistemologies') which underpin a scenario approach. Drawing on previous environmental scenario projects, we distinguish and describe two main types in this new typology: 'problem-focused' and 'actor-centric'. This leads in turn to our suggestion for a third type, which we call 'RIMA'-'reflexive interventionist or multi-agent based'. This approach to scenarios emphasizes the importance of the involvement of different epistemologies in a scenario-based process of action learning in the public interest. We suggest that, by combining the epistemologies apparent in the previous two types, this approach can create a more effective bridge between longer-term thinking and more immediate actions. Our description is aimed at scenario practitioners in general, as well as those who work with (environmental) scenarios that address global challenges.

  13. "Dedicated To The Continued Education, Training and Demonstration of PEM Fuel Cell Powered Lift Trucks In Real-World Applications."

    Energy Technology Data Exchange (ETDEWEB)

    Dever, Thomas J.

    2011-11-29

    operating large fleets. As a long-standing lift truck dealership, LiftOne was able to introduce the fuel cells to such companies in the demanding applications. Accomplishments vs Objectives: We were successful in respect to the stated objectives. The Education Segment's H2 Education Sessions were able to introduce fuel cell technology to many companies and reached the intended broad audience. Also, demos of the lift truck at the sessions as well as the conferences; expos and area events provided great additional exposure. The Deployments were successful in allowing the 6 participating companies to test the 2 fuel cell powered lift trucks in their demanding applications. One of the 6 sites (BMW) eventually adopted over 80 fuel cells from Plug Power. LiftOne was one of the 3 fuel cell demonstrators at BMW for this trial and played a major role in helping to prove the viability and efficiency of this alternative form of energy for BMW. The other 5 companies that participated in the project's deployments were encouraged by the trials and while not converting over to fuel cell power at this time, expressed the desire to revisit acquisition scenarios in the near future as the cost of fuel cells and infrastructure continue to improve. The Education sessions began in March of 2009 at the 7 LiftOne Branches and continued throughout the duration of the project. Attendees came from a large base of lift truck users in North Carolina, South Carolina and Virginia. The sessions were free and invitations were sent out to potential users and companies with intrigue. In addition to the Education content at the sessions (which was offered in a 'H2 101' format), LiftOne was able to demonstrate a working fuel cell powered lift truck, which proved to be a big draw with the 'hands on' experience. LiftOne also demo'd the fuel cell lift trucks at many conferences, expos, professional association meetings, trade shows and 'Green' events in major cities

  14. IMPROVING THE ORGANIZATION OF THE SHOVEL-TRUCK SYSTEMS IN OPEN-PIT COAL MINES

    Directory of Open Access Journals (Sweden)

    Mark KORYAGIN

    2017-06-01

    Full Text Available The aim of the study is to reduce idle times of mining trucks and shovels in an open-pit coal mine. A heuristic algorithm for making dispatching decisions in conditions of dynamic allocation of trucks is developed. Priority parameters for choosing the shovel after the end-of-truck unloading are introduced. Also, an algorithm for searching for the optimal priority parameters to satisfy the required efficiency criterion is developed. This algorithm is based on a simulation model of a shovel-truck system. The proposed approach is applicable in terms of the group of shovels with a common dump point in various open-pit coal mines. The importance of this work lies in the fact that the proposed model takes into account the random factors related with the duration of loading and dumping, truck movement, repair of shovels and haul trucks, as well as the duration of periods between repairs.

  15. Quantifying Four Scenarios for Europe

    International Nuclear Information System (INIS)

    Lejour, A.

    2003-10-01

    This study presents four economic scenarios for Europe until 2040. The scenarios are developed around two key uncertainties: international cooperation and institutional reforms. In the scenarios Strong Europe (SE) and Global Economy (GE), international cooperation is prominent, while the other scenarios, Regional Communities (RC) and Transatlantic Market (TM), feature limited international cooperation. Public institutions are important in Strong Europe and Regional Communities. In Global Economy and Transatlantic Market the role of the public sector is limited. There is more room for private initiatives in these scenarios. To illustrate the scenarios, this document presents quantitative developments described with an applied general equilibrium model developed at CPB: WorldScan. By using this model we are able to derive consistency between developments in the scenarios and to apply common economic mechanisms. The variation in the outcomes for the scenarios is derived by introducing differences in exogenous trends. This document explains and motivates these differences

  16. Multiscale scenarios for nature futures

    CSIR Research Space (South Africa)

    Rosa, IMD

    2017-09-01

    Full Text Available Targets for human development are increasingly connected with targets for nature, however, existing scenarios do not explicitly address this relationship. Here, we outline a strategy to generate scenarios centred on our relationship with nature...

  17. Planning of Truck Platoons: a Literature Review and Directions for Future Research

    OpenAIRE

    Kishore Bhoopalam, Anirudh; Agatz, Niels; Zuidwijk, Rob

    2017-01-01

    textabstractA truck platoon is a set of virtually linked trucks that drive closely behind one another using automated driving technology. Benefits of truck platooning include cost savings, reduced emissions, and more efficient utilization of road capacity. To fully reap these benefits in the initial phases requires careful planning of platoons based on trucks’ itineraries and time schedules. This paper provides a framework to classify various new transportation planning problems that arise in...

  18. Assessing crash risk considering vehicle interactions with trucks using point detector data.

    Science.gov (United States)

    Hyun, Kyung Kate; Jeong, Kyungsoo; Tok, Andre; Ritchie, Stephen G

    2018-03-12

    Trucks have distinct driving characteristics in general traffic streams such as lower speeds and limitations in acceleration and deceleration. As a consequence, vehicles keep longer headways or frequently change lane when they follow a truck, which is expected to increase crash risk. This study introduces several traffic measures at the individual vehicle level to capture vehicle interactions between trucks and non-trucks and analyzed how the measures affect crash risk under different traffic conditions. The traffic measures were developed using headways obtained from Inductive Loop Detectors (ILDs). In addition, a truck detection algorithm using a Gaussian Mixture (GM) model was developed to identify trucks and to estimate truck exposure from ILD data. Using the identified vehicle types from the GM model, vehicle interaction metrics were categorized into three groups based on the combination of leading and following vehicle types. The effects of the proposed traffic measures on crash risk were modeled in two different cases of prior- and non-crash using a case-control approach utilizing a conditional logistic regression. Results showed that the vehicle interactions between the leading and following vehicle types were highly associated with crash risk, and further showed different impacts on crash risk by traffic conditions. Specifically, crashes were more likely to occur when a truck following a non-truck had shorter average headway but greater headway variance in heavy traffic while a non-truck following a truck had greater headway variance in light traffic. This study obtained meaningful conclusions that vehicle interactions involved with trucks were significantly related to the crash likelihood rather than the measures that estimate average traffic condition such as total volume or average headway of the traffic stream. Copyright © 2018 Elsevier Ltd. All rights reserved.

  19. Truck frame welding reparation by steel covered electrodes with varied amount of Ni and Mo

    OpenAIRE

    Tomasz WĘGRZYN; Michał MIROS; Damian HADRYŚ; Abilio Manuel Pereira da SILVA

    2010-01-01

    This paper attempts to study safety and exploitation conditions of weld steel structure reparation of car body truck frames. Car (auto) body is the name given to the portion of an automobile which gives it shape. The work is a theoretical investigation and concentrates on structural integrity and vehicle safety after the reparation welding of truck frames. To study the effects of the frame flexibility and resistance, the truck frame has been welded by steel electrodes with varied amount of Ni...

  20. Fuel consumption from vehicles of China until 2030 in energy scenarios

    International Nuclear Information System (INIS)

    Zhang Qingyu; Tian Weili; Zheng Yingyue; Zhang Lili

    2010-01-01

    Estimation of fuel (gasoline and diesel) consumption for vehicles in China under different long-term energy policy scenarios is presented here. The fuel economy of different vehicle types is subject to variation of government regulations; hence the fuel consumption of passenger cars (PCs), light trucks (Lts), heavy trucks (Hts), buses and motor cycles (MCs) are calculated with respect to (i) the number of vehicles, (ii) distance traveled, and (iii) fuel economy. On the other hand, the consumption rate of alternative energy sources (i.e. ethanol, methanol, biomass-diesel and CNG) is not evaluated here. The number of vehicles is evaluated using the economic elastic coefficient method, relating to per capita gross domestic product (GDP) from 1997 to 2007. The Long-range Energy Alternatives Planning (LEAP) system software is employed to develop a simple model to project fuel consumption in China until 2030 under these scenarios. Three energy consumption decrease scenarios are designed to estimate the reduction of fuel consumption: (i) 'business as usual' (BAU); (ii) 'advanced fuel economy' (AFE); and (iii) 'alternative energy replacement' (AER). It is shown that fuel consumption is predicted to reach 992.28 Mtoe (million tons oil equivalent) with the BAU scenario by 2030. In the AFE and AER scenarios, fuel consumption is predicted to be 734.68 and 600.36 Mtoe, respectively, by 2030. In the AER scenario, fuel consumption in 2030 will be reduced by 391.92 (39.50%) and 134.29 (18.28%) Mtoe in comparison to the BAU and AFE scenarios, respectively. In conclusion, our models indicate that the energy conservation policies introduced by governmental institutions are potentially viable, as long as they are effectively implemented.

  1. 40 Years of Shell Scenarios

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-02-15

    Shell has been using scenario planning for four decades. During that time these scenarios have helped the company and governments across the world to make better strategic choices. Scenarios provide lenses that help see future prospects more clearly, make richer judgments and be more sensitive to uncertainties. Discover how the Shell Scenarios team has helped guide decision makers at major moments in history and get a peek at the team future focus, including the intricate relationship between energy, water and food.

  2. Scenario Planning in Higher Education.

    Science.gov (United States)

    Rieley, James B.

    1997-01-01

    Proposes scenario planning in preparing for the future of higher education. Delineates a methodology for effective scenario planning: identifying potential future scenarios; examining social, economic, political, environmental, and technological influences; exploring mental models while looking through systems maps, and developing potential…

  3. Engaging Personas and Narrative Scenarios

    DEFF Research Database (Denmark)

    Nielsen, Lene

    2004-01-01

    design ideas. The concept of engaging personas and narrative scenario explores personas in the light of what what it is to identify with and have empathy with a character. The concept of narrative scenarios views the narrative as aid for exploration of design ideas. Both concepts incorporate...... a distinktion between creating, writing and reading. Keywords: personas, scenarios, user-centered design, HCI...

  4. Biomass Scenario Model Scenario Library: Definitions, Construction, and Description

    Energy Technology Data Exchange (ETDEWEB)

    Inman, D.; Vimmerstedt, L.; Bush, B.; Peterson, S.

    2014-04-01

    Understanding the development of the biofuels industry in the United States is important to policymakers and industry. The Biomass Scenario Model (BSM) is a system dynamics model of the biomass-to-biofuels system that can be used to explore policy effects on biofuels development. Because of the complexity of the model, as well as the wide range of possible future conditions that affect biofuels industry development, we have not developed a single reference case but instead developed a set of specific scenarios that provide various contexts for our analyses. The purpose of this report is to describe the scenarios that comprise the BSM scenario library. At present, we have the following policy-focused scenarios in our library: minimal policies, ethanol-focused policies, equal access to policies, output-focused policies, technological diversity focused, and the point-of-production- focused. This report describes each scenario, its policy settings, and general insights gained through use of the scenarios in analytic studies.

  5. Electric urban delivery trucks: energy use, greenhouse gas emissions, and cost-effectiveness.

    Science.gov (United States)

    Lee, Dong-Yeon; Thomas, Valerie M; Brown, Marilyn A

    2013-07-16

    We compare electric and diesel urban delivery trucks in terms of life-cycle energy consumption, greenhouse gas (GHG) emissions, and total cost of ownership (TCO). The relative benefits of electric trucks depend heavily on vehicle efficiency associated with drive cycle, diesel fuel price, travel demand, electric drive battery replacement and price, electricity generation and transmission efficiency, electric truck recharging infrastructure, and purchase price. For a drive cycle with frequent stops and low average speed such as the New York City Cycle (NYCC), electric trucks emit 42-61% less GHGs and consume 32-54% less energy than diesel trucks, depending upon vehicle efficiency cases. Over an array of possible conditions, the median TCO of electric trucks is 22% less than that of diesel trucks on the NYCC. For a drive cycle with less frequent stops and high average speed such as the City-Suburban Heavy Vehicle Cycle (CSHVC), electric trucks emit 19-43% less GHGs and consume 5-34% less energy, but cost 1% more than diesel counterparts. Considering current and projected U.S. regional electricity generation mixes, for the baseline case, the energy use and GHG emissions ratios of electric to diesel trucks range from 48 to 82% and 25 to 89%, respectively.

  6. Logistics of in-wood chipping and trucking of chips; Palstahaketuksen logistinen ketju

    Energy Technology Data Exchange (ETDEWEB)

    Nuuja, J. [Joensuu Univ. (Finland). Faculty of Forestry; Asikainen, A. [Metsaeosaamiskeskus, Joensuu (Finland). Joensuu Science Park

    1996-12-31

    In this study a in wood chipper and truck transport of chips were modelled and studied by discrete-event simulation. The input data, which included stand characteristics and information about transport distances was compiled by GRASS-program. This data based on the inventory done by Forestry Center TAPIO. With the model various transport alternatives were compared and the effect of work condition factors were studied. It was find out, that a long distance transport with interchangeable container truck gives better productivity than a truck with a trailer. This results from shorter loading time for the interchangeable container truck

  7. Was It Really Worth Pain? Refurbishment of Mercedes-Benz Trucks by Botswana Defence Force

    National Research Council Canada - National Science Library

    Rangobana, Samuel A; Alkebaisi, Hussain K

    2005-01-01

    .... Logistics statistics, for refurbished trucks returned to user units, are also gathered from the asset management software database, Mincom Ellipse, in use by the Botswana Defence Force Mechanical...

  8. An Evaluation of the Potential for Shifting of Freight from Truck to Rail and Its Impacts on Energy Use and GHG Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Yan [Argonne National Lab. (ANL), Argonne, IL (United States); Vyas, Anant D. [Argonne National Lab. (ANL), Argonne, IL (United States); Guo, Zhaomiao [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-06-01

    This report summarizes our evaluation of the potential energy-use and GHG-emissions reduction achieved by shifting freight from truck to rail under a most-likely scenario. A sensitivity analysis is also included. The sensitivity analysis shows changes in energy use and GHG emissions when key parameters are varied. The major contribution and distinction from previous studies is that this study considers the rail level of service (LOS) and commodity movements at the origin-destination (O-D) level. In addition, this study considers the fragility and time sensitivity of each commodity type.

  9. Scenario development methodologies

    International Nuclear Information System (INIS)

    Eng, T.; Hudson, J.; Stephansson, O.

    1994-11-01

    In the period 1981-1994, SKB has studied several methodologies to systematize and visualize all the features, events and processes (FEPs) that can influence a repository for radioactive waste in the future. All the work performed is based on the terminology and basic findings in the joint SKI/SKB work on scenario development presented in the SKB Technical Report 89-35. The methodologies studied are a) Event tree analysis, b) Influence diagrams and c) Rock Engineering Systems (RES) matrices. Each one of the methodologies is explained in this report as well as examples of applications. One chapter is devoted to a comparison between the two most promising methodologies, namely: Influence diagrams and the RES methodology. In conclusion a combination of parts of the Influence diagram and the RES methodology is likely to be a promising approach. 26 refs

  10. Scenario development methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Eng, T. [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Hudson, J. [Rock Engineering Consultants, Welwyn Garden City, Herts (United Kingdom); Stephansson, O. [Royal Inst. of Tech., Stockholm (Sweden). Div. of Engineering Geology; Skagius, K.; Wiborgh, M. [Kemakta, Stockholm (Sweden)

    1994-11-01

    In the period 1981-1994, SKB has studied several methodologies to systematize and visualize all the features, events and processes (FEPs) that can influence a repository for radioactive waste in the future. All the work performed is based on the terminology and basic findings in the joint SKI/SKB work on scenario development presented in the SKB Technical Report 89-35. The methodologies studied are (a) Event tree analysis, (b) Influence diagrams and (c) Rock Engineering Systems (RES) matrices. Each one of the methodologies is explained in this report as well as examples of applications. One chapter is devoted to a comparison between the two most promising methodologies, namely: Influence diagrams and the RES methodology. In conclusion a combination of parts of the Influence diagram and the RES methodology is likely to be a promising approach. 26 refs.

  11. Strategic Scenario Construction Made Easy

    DEFF Research Database (Denmark)

    Duus, Henrik Johannsen

    2016-01-01

    of scenarios in business has, in many cases, remained a cumbersome affair. Very often a large group of consultants, employees and staff is involved in the development of scenarios and strategies, thus making the whole process expensive in terms of time, money and human resources. In response, this article uses...... insights from the area of strategic forecasting (of which scenario planning is a proper subset) and experiences gained from a recent course in that area to develop a simpler, more direct, hands-on method for scenario construction and to provide several ideas for scenario construction that can be used...

  12. Integration and consolidation of border freight transportation data for planning applications and characterization of NAFTA truck loads for aiding in transportation infrastructure management : second year.

    Science.gov (United States)

    2008-07-01

    Average Daily Truck Traffic (ADTT) increased dramatically in Texas in the 1990s partly because of the : implementation of the North American Free Trade Agreement (NAFTA). Accurate information on truck : volumes and truck characteristics is critical t...

  13. Field Evaluation of Medium-Duty Plug-in Electric Delivery Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Prohaska, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Simpson, Mike [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ragatz, Adam [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kelly, Kenneth [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, Kandler [National Renewable Energy Lab. (NREL), Golden, CO (United States); Walkowicz, Kevin [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-12-01

    This report focuses on medium-duty electric delivery vehicles operated by Frito-Lay North America (FLNA) at its Federal Way, Washington, distribution center. The 100% electric drive system is an alternative to conventional diesel delivery trucks and reduces both energy consumption and carbon dioxide (CO2) emissions. The vehicles' drive cycles and operation are analyzed and compared to demonstrate the importance of matching specific electric vehicle (EV) technologies to the appropriate operational duty cycle. The results of this analysis show that the Smith Newton EVs demonstrated a 68% reduction in energy consumption over the data reporting period compared to the conventional diesel vehicles, as well as a 46.4% reduction in CO2 equivalent emissions based on the local energy generation source. In addition to characterizing the in-use performance of the EVs compared to the conventional diesels, detailed facility load data were collected at the main building power feed as well as from each of the 10 EV chargers to better understand the broader implications associated with commercial EV deployment. These facility loads were incorporated into several modeling scenarios to demonstrate the potential benefits of integrating onsite renewables.

  14. The risks of Bobtail truck LPG (Liquefied Petroleum Gases) distribution in urban areas

    Energy Technology Data Exchange (ETDEWEB)

    Leal, Cesar A. [Det Norske Veritas (DNV), Oslo (Norway)], e-mail: cesar.leal@dnv.com

    2008-07-01

    The use of 'Bobtail' trucks (6 and 9 ton) for distribution of Liquefied Petroleum Gas (LPG) in Brazilian cities represents a new and mobile source of risk. In this paper, it will be presented a discussion about some of the possible accident scenarios that can occur with this kind of vehicle, with emphasis on the possible consequences (BLEVE/fireball). The goal is to spread information and call attention of Government Authorities and gas distribution companies, as well as the general public, about this source of risk. In the case of a 9 ton fireball, fatalities could be expected up to 176 m, according to TNO models. Collapse of the tank engulfed in fire is expected in 10 to 20 minutes, a too short time interval for the arrival of a fire brigade and control of the situation. Suggestions are presented for the use of insulating coating in the tanks capable of withstanding an external fire for two hours without collapsing and the realization of a risk study for estimation of the impact of the use of insulation in terms of risk reduction for the population and a comparison of risks associated to the two forms of LPG distribution. (author)

  15. Psychoactive substance use by truck drivers: a systematic review.

    Science.gov (United States)

    Girotto, Edmarlon; Mesas, Arthur Eumann; de Andrade, Selma Maffei; Birolim, Marcela Maria

    2014-01-01

    The aim of this study was to summarise the scientific evidence on the prevalence of psychoactive substance use and on the factors associated with their intake among truck drivers. A systematic review was performed in the databases PubMed, Scientific Electronic Library Online, Latin American and Caribbean Health Sciences, and Cochrane and 36 cross-sectional studies were identified with quantitative results about the use of psychoactive substances by truck drivers. Out of these, 28 were carried out in countries with large land areas and 23 obtained their information through self-reporting. The most frequently studied substances were alcohol (n=25), amphetamines (n=17), marijuana (n=16) and cocaine (n=13). The prevalence of the use of these substances greatly varied: alcohol (0.1-91.0%); amphetamines (0.2-82.5%), marijuana (0.2-29.9%), cocaine (0.1-8.3%). The frequency of substance use was lower in studies that investigated the presence of these substances in biological samples than in those based on self-reported use. In 12 studies that evaluated factors associated with the intake of psychoactive substances, the following stood out: younger age, higher income, longer trips, alcohol consumption, driving in the night shift, travelling interstate routes, long or short sleep, fewer hours of rest, little experience of the driver, connection with small and medium sized companies, income below levels determined by labour agreements, productivity-based earnings and prior involvement in accidents. The frequency of psychoactive substance use by truck drivers seems to be high, although that greatly varies according to the type of substance and the method of collecting the information. The use of these substances was mainly associated with indicators of poor working conditions.

  16. Aberrant Behaviors and Road Accidents among Iranian Truck Drivers, 2010

    Directory of Open Access Journals (Sweden)

    Amir Houshang Mehrparvar

    2011-12-01

    Full Text Available structural dimensions of which as well as technologic failures such as road quality, and tech-nical faults of automobiles, need to be assessed in detail. Iran has the first order in the world for deadly road accidents. This study was designed to assess the association between aberrant behaviors of truck drivers and the incidence of road accidents in Yazd, center of Iran, in 2010.Methods: This cross-sectional descriptive-analytic study was conducted on 300 truck drivers in Yazd. We used 3 questionnaires, including one for demographic data, Driver Behavior Questionnaire (DBQ, and one for drivers' self-evaluation of the of their driving.Results: Five types of the behavior had the highest frequency: Misjudge speed of oncoming vehicle when overtaking.; Deliberately disregard the speed limits late at night or very early in the morning.; Ignore 'give way' signs, and narrowly avoid colliding with traffic having right of way.; Stuck behind a slow-moving vehicle on a two-lane highway, you are driven by frustration to try to overtake in risky circumstances.; Drive with only 'half-an-eye' on the road while looking at a map, changing a cassette or radio channel, etc. The more the driver's driv-ing was influenced by emotional and mental states the more deliberate violations and slips.Conclusion: Among truck drivers, safety has not developed sufficiently, and because of the dangers of road accidents both for the drivers and other people and its economic losses, the importance of the presenting some solutions is completely obvious.

  17. Recovery Act--Class 8 Truck Freight Efficiency Improvement Project

    Energy Technology Data Exchange (ETDEWEB)

    Trucks, Daimler [Daimler Trucks North America Llc, Portland, OR (United States)

    2015-07-26

    Daimler Trucks North America completed a five year, $79.6M project to develop and demonstrate a concept vehicle with at least 50% freight efficiency improvement over a weighted average of several drive cycles relative to a 2009 best-in-class baseline vehicle. DTNA chose a very fuel efficient baseline vehicle, the 2009 Freightliner Cascadia with a DD15 engine, yet successfully demonstrated a 115% freight efficiency improvement. DTNA learned a great deal about the various technologies that were incorporated into Super Truck and those that, through down-selection, were discarded. Some of the technologies competed with each other for efficiency, and notably some of the technologies complemented each other. For example, we found that Super Truck’s improved aerodynamic drag resulted in improved fuel savings from eCoast, relative to a similar vehicle with worse aerodynamic drag. However, some technologies were in direct competition with each other, namely the predictive technologies which use GPS and 3D digital maps to efficiently manage the vehicles kinetic energy through controls and software, versus hybrid which is a much costlier technology that essentially targets the same inefficiency. Furthermore, the benefits of a comprehensive, integrated powertrain/vehicle approach was proven, in which vast improvements in vehicle efficiency (e.g. lower aero drag and driveline losses) enabled engine strategies such as downrating and downspeeding. The joint engine and vehicle developments proved to be a multiplier-effect which resulted in large freight efficiency improvements. Although a large number of technologies made the selection process and were used on the Super Truck demonstrator vehicle, some of the technologies proved not feasible for series production.

  18. Outputs and cost of HIV prevention programmes for truck drivers in Andhra Pradesh, India

    Directory of Open Access Journals (Sweden)

    Dandona Rakhi

    2009-05-01

    Full Text Available Abstract Background HIV prevention programmes for truck drivers form part of the HIV control efforts, but systematic data on the outputs and cost of providing such services in India are not readily available for further planning and use of resources. Methods Detailed cost and output data were collected from written records and interviews for 2005–2006 fiscal year using standardized methods at six sampled HIV prevention programmes for truck drivers in the Indian state of Andhra Pradesh. The total economic cost for these programmes was computed and the relation of unit cost of services per truck driver with programme scale was assessed using regression analysis. Results A total of 120,436 truck drivers were provided services by the six programmes of which 55.9% were long distance truck drivers. The annual economic cost of providing services to a truck driver varied between programmes from US$ 1.52 to 4.56 (mean US$ 2.49. There was an inverse relation between unit economic cost of serving a truck driver and scale of the programme (R2 = 0.63; p = 0.061. The variation between programmes in the average number of contacts made by the programme staff with truck drivers was 1.3 times versus 5.8 times for contacts by peer educators. Only 1.7% of the truck drivers were referred by the programmes for counseling and HIV testing. Conclusion These data provide information for further planning of HIV prevention programmes for truck drivers and estimating the resources needed for such programmes. The findings suggest the need to strengthen the role of peer educators and increase referral of truck drivers for HIV testing.

  19. Its Not a Big Truck: Examining Cyber Metaphors

    Science.gov (United States)

    2010-02-01

    mortality in June of 2006 when he said the Internet is “not a big truck. It’s a series of tubes.” Along with inadvertently creating a new Internet meme [a...and people who publically misunderstand the Internet run the very real risk of inad- vertently creating their very own meme . That’s not nearly as fun...catch- phrase or idea that spreads online], the senator’s unfortunate attempt to explain the Internet highlights both the central role of metaphor in

  20. Assessing tether anchor labeling and usability in pickup trucks.

    Science.gov (United States)

    Klinich, Kathleen D; Manary, Miriam A; Malik, Laura A; Flannagan, Carol A; Jermakian, Jessica S

    2018-04-03

    The objective of this study was to investigate vehicle factors associated with child restraint tether use and misuse in pickup trucks and evaluate 4 labeling interventions designed to educate consumers on proper tether use. Volunteer testing was performed with 24 subjects and 4 different pickup trucks. Each subject performed 8 child restraint installations among the 4 pickups using 2 forward-facing restraints: a Britax Marathon G4.1 and an Evenflo Triumph. Vehicles were selected to represent 4 different implementations of tether anchors among pickups: plastic loop routers (Chevrolet Silverado), webbing routers (Ram), back wall anchors (Nissan Frontier), and webbing routers plus metal anchors (Toyota Tundra). Interventions included a diagram label, Quick Response (QR) Code linked to video instruction, coordinating text label, and contrasting text tag. Subjects used the child restraint tether in 93% of trials. However, tether use was completely correct in only 9% of trials. An installation was considered functional if the subject attached the tether to a tether anchor and had a tight installation (ignoring routing and head restraint position); 28% of subjects achieved a functional installation. The most common installation error was attaching the tether hook to the anchor/router directly behind the child restraint (near the top of the seatback) rather than placing the tether through the router and attaching it to the anchor in the adjacent seating position. The Nissan Frontier, with the anchor located on the back wall of the cab, had the highest rate of correct installations but also had the highest rate of attaching the tether to components other than the tether anchor (seat adjustor, child restraint storage hook, around head restraint). None of the labeling interventions had a significant effect on correct installation; not a single subject scanned the QR Code to access the video instruction. Subjects with the most successful installations spent extensive time

  1. Truck Roll Stability Data Collection and Analysis; TOPICAL

    International Nuclear Information System (INIS)

    Stevens, SS

    2001-01-01

    The principal objective of this project was to collect and analyze vehicle and highway data that are relevant to the problem of truck rollover crashes, and in particular to the subset of rollover crashes that are caused by the driver error of entering a curve at a speed too great to allow safe completion of the turn. The data are of two sorts-vehicle dynamic performance data, and highway geometry data as revealed by vehicle behavior in normal driving. Vehicle dynamic performance data are relevant because the roll stability of a tractor trailer depends both on inherent physical characteristics of the vehicle and on the weight and distribution of the particular cargo that is being carried. Highway geometric data are relevant because the set of crashes of primary interest to this study are caused by lateral acceleration demand in a curve that exceeds the instantaneous roll stability of the vehicle. An analysis of data quality requires an evaluation of the equipment used to collect the da ta because the reliability and accuracy of both the equipment and the data could profoundly affect the safety of the driver and other highway users. Therefore, a concomitant objective was an evaluation of the performance of the set of data-collection equipment on the truck and trailer. The objective concerning evaluation of the equipment was accomplished, but the results were not entirely positive. Significant engineering apparently remains to be done before a reliable system can be fielded. Problems were identified with the trailer to tractor fiber optic connector used for this test. In an over-the-road environment, the communication between the trailer instrumentation and the tractor must be dependable. In addition, the computer in the truck must be able to withstand the rigors of the road. The major objective-data collection and analysis-was also accomplished. Using data collected by instruments on the truck, a ''bad-curve'' database can be generated. Using this database

  2. Comprehensive Truck Size and Weight (TS&W) Study. Phase 1-synthesis, working paper 12 : energy conservation and truck size and weight regulations

    Science.gov (United States)

    1995-02-01

    The research on various truck size and weight considerations and energy conservation is limited. Following the energy crisis in the mid 1970s, there was significant interest and research on energy conservation. Most of the references cited in this wo...

  3. Evaluating the effects of heavy sugar cane truck operations on repair cost of low volume highways : technical summary report.

    Science.gov (United States)

    2008-10-01

    Current Louisiana state laws allow truck operators hauling certain agricultural commodities to purchase : overweight permits and haul at gross vehicle weights (GVW) in excess of the legislated GVW limit of : 80,000 lb. For instance, sugar cane trucke...

  4. The application of smart phone, weight-mile truck data to support freight-modeling, performance measures and planning.

    Science.gov (United States)

    2013-08-01

    Oregon is one of the few states that currently charge a commercial truck weight-mile tax (WMT). The Oregon Department of : Transportation (ODOT) has developed a data-collection system Truck Road Use Electronics (TRUE) to simplify WMT : collec...

  5. Research on tractive power of KZC-5 rear dump truck in underground mine

    International Nuclear Information System (INIS)

    Lei Zeyong

    2003-01-01

    The tractive power of KZC-5 rear dump truck in underground mine is studied in this paper. The principles and ways of defining the power are discussed. It is proved that the power of KZC-5 rear dump truck in underground mine is reasonable in the industrial scale test

  6. Impact of trucking network flow on preferred biorefinery locations in the southern United States

    Science.gov (United States)

    Timothy M. Young; Lee D. Han; James H. Perdue; Stephanie R. Hargrove; Frank M. Guess; Xia Huang; Chung-Hao Chen

    2017-01-01

    The impact of the trucking transportation network flow was modeled for the southern United States. The study addresses a gap in existing research by applying a Bayesian logistic regression and Geographic Information System (GIS) geospatial analysis to predict biorefinery site locations. A one-way trucking cost assuming a 128.8 km (80-mile) haul distance was estimated...

  7. 75 FR 33663 - Commercial Driver's License (CDL) Standards; Volvo Trucks North America, Renewal of Exemption

    Science.gov (United States)

    2010-06-14

    ... Federal Motor Carrier Safety Administration Commercial Driver's License (CDL) Standards; Volvo Trucks.... ACTION: Notice of renewal of exemption; request for comments. SUMMARY: FMCSA renews Volvo Trucks North America's (Volvo) exemption from the Agency's requirement for certain drivers of commercial motor vehicles...

  8. 75 FR 47880 - Commercial Driver's License (CDL) Standards; Volvo Trucks North America, Renewal of Exemption

    Science.gov (United States)

    2010-08-09

    ... Federal Motor Carrier Safety Administration Commercial Driver's License (CDL) Standards; Volvo Trucks.... ACTION: Notice of final disposition. SUMMARY: FMCSA announces its decision to continue in effect Volvo Trucks North America's (Volvo) exemption for five of its drivers to enable them to test-drive commercial...

  9. 75 FR 2921 - Commercial Driver's License Standards: Application for Exemption; Volvo Trucks North America (Volvo)

    Science.gov (United States)

    2010-01-19

    ... Exemption; Volvo Trucks North America (Volvo) AGENCY: Federal Motor Carrier Safety Administration (FMCSA... Volvo Trucks North America (Volvo) has applied for an exemption from the Federal requirement for a driver of commercial motor vehicles (CMVs) to hold a commercial driver's license (CDL). Volvo requests...

  10. 75 FR 8181 - Commercial Driver's License Standards: Application for Exemption; Volvo Trucks North America (Volvo)

    Science.gov (United States)

    2010-02-23

    ... Exemption; Volvo Trucks North America (Volvo) AGENCY: Federal Motor Carrier Safety Administration (FMCSA... Volvo Trucks North America (Volvo) has applied for an exemption from the Federal requirement for a driver of commercial motor vehicles (CMVs) to hold a commercial driver's license (CDL). Volvo requests...

  11. 75 FR 45198 - Commercial Driver's License (CDL) Standards; Volvo Trucks North America, Renewal of Exemption

    Science.gov (United States)

    2010-08-02

    ... Federal Motor Carrier Safety Administration Commercial Driver's License (CDL) Standards; Volvo Trucks... requirement to hold a commercial driver's license (CDL) submitted by Volvo Trucks North America (Volvo) on behalf of an employee. Volvo requested renewal of the CDL exemption for a Swedish engineer employed by...

  12. 76 FR 4412 - Commercial Driver's License (CDL) Standards; Volvo Trucks North America, Renewal of Exemption

    Science.gov (United States)

    2011-01-25

    ... Federal Motor Carrier Safety Administration Commercial Driver's License (CDL) Standards; Volvo Trucks.... ACTION: Notice of final disposition. SUMMARY: FMCSA announces its final decision regarding Volvo Trucks North America's (Volvo) application for an exemption for Andreas Hamsten to enable him to continue to...

  13. 75 FR 33662 - Commercial Driver's License (CDL) Standards; Volvo Trucks North America, Inc.'s Exemption...

    Science.gov (United States)

    2010-06-14

    ... Federal Motor Carrier Safety Administration Commercial Driver's License (CDL) Standards; Volvo Trucks... announces its decision to grant Volvo Trucks North America, Inc.'s (Volvo) application for an exemption for two Volvo drivers to drive commercial motor vehicles (CMVs) in the United States without possessing...

  14. 75 FR 35515 - Commercial Driver's License (CDL) Standards: Granting of Exemption; Volvo Trucks North America

    Science.gov (United States)

    2010-06-22

    ... Exemption; Volvo Trucks North America AGENCY: Federal Motor Carrier Safety Administration (FMCSA), DOT... decision to grant Volvo Trucks North America, Inc.'s (Volvo) application for exemption to enable one of its... license (CDL) issued by one of the States. Volvo asserts that the exemption is necessary to support a...

  15. EVALUATION OF FUEL CELL AUXILIARY POWER UNITS FOR HEAVY-DUTY DIESEL TRUCKS

    Science.gov (United States)

    A large number of heavy-duty trucks idle a significant amount. Heavy-duty line-haul truck engines idle about 30-50% of the time the engine is running. Drivers idle engines to power climate control devices (e.g., heaters and air conditioners) and sleeper compartment accessories (e...

  16. Locomotor diseases among male long-haul truck drivers and other professional drivers

    DEFF Research Database (Denmark)

    Jensen, Anker; Kaerlev, Linda; Tüchsen, Finn

    2007-01-01

    -249) and for other truck drivers (SHR: 130, 95% CI: 108-156) compared to bus drivers (SHR: 110, 95% CI: 79-149). All drivers had high SHR for lesions of the ulnar nerve (SHR: 159, 95% CI: 119-207), especially bus drivers (SHR: 197, 95% CI: 116-311). Long-haul truck drivers had high SHRs for synovitis and bursitis...

  17. Six Reasons why hours of service regulations for truck drivers are violated

    DEFF Research Database (Denmark)

    Grøn, Sisse

    2008-01-01

      ABSTRACT Two decades of research has established a correlation between tiredness and fatigue, and traffic accident involving truck drivers.  Regulations limiting the driving hours of truck drivers thus are necessary precautions. But compliance is a problem. The answer from authorities tend to b...

  18. When does stress end? : Evidence of a prolonged stress reaction in shiftworking truck drivers

    NARCIS (Netherlands)

    Ulhôa, Melissa Ara Jo; Marqueze, Elaine Cristina; Kantermann, Thomas; Skene, Debra; Moreno, Claudia

    2011-01-01

    This study aimed to analyze individual cortisol levels in relation to work conditions, sleep, and health parameters among truck drivers working day shifts (n = 21) compared to those working irregular shifts (n = 21). A total of 42 male truck drivers (39.8 (+/-) 6.2 yrs) completed questionnaires

  19. A Comparative Study of Back Pain among Taxi and Truck Drivers in ...

    African Journals Online (AJOL)

    Data was analyzed using SSPSS version 20. Descriptive and analytical statistics to analyze and present data. The prevalence of back pain in Port Harcourt for taxi drivers was 70.4% and 71.4% for truck drivers. The prevalence among truck drivers was due to age ,sitting position and shock absorbers. However variables like ...

  20. Structural evaluation for the core sampling trucks, RMCS operations, 200 Area

    International Nuclear Information System (INIS)

    Islam, M.A.

    1996-01-01

    This report evaluates the structural adequacy and the integrity of the existing core sampling trucks to withstand impact should the trucks drop off the ramp, either onto the soft ground or onto a non-yielding surface due to operational error, wind, or earthquake. The report also addresses if the allowable tank dome load will be exceeded by the addition of the impact load

  1. Risk of commercial truck fires in the United States : an exploratory data analysis

    Science.gov (United States)

    2012-06-29

    Large trucks are involved in only 8 percent of fatal crashes per year, but 17 percent of fatal fires. The scope of the current body of research is limited. Studies have treated truck fires generally as a subset of vehicle fires or in their own right ...

  2. Analysis of vehicle headway distribution on multi-lane freeway considering car–truck interaction

    Directory of Open Access Journals (Sweden)

    Dewen Kong

    2016-04-01

    Full Text Available The primary objective of this study is to identify the characteristics of vehicle headway on multi-lane freeway under lane management in China considering car–truck interaction. More specifically, the study focused on answering the following two questions: (1 whether the car–truck interaction has impact on headway, that is, headway varies by different leading and following vehicle types and (2 what is the best-fitted distribution model for particular headway type under lane management. The team collected traffic data, including traffic flow rates, percentage of trucks, speeds, headways, and so on from four segments of Shanghai-Nanjing freeway, Jiangsu Province in China. Then, some statistical methods were used to analyze the vehicle headway. It was found that car–car, car/truck, and truck–truck headways are significantly different from each other. Also, the traffic flow rate, percentage of trucks, and lane position were found to have an influence on the vehicle headway through the tests. Using the maximum-likelihood estimation, Kolmogorov–Smirnov test, and chi-square test techniques, the distribution models and parameter functions for each headway type were built and validated. The results showed that lognormal model is suitable for car–car and truck–truck headway types, and inverse Gaussian model fits the car/truck headway type well.

  3. Analysis of driver critical reason and years of driving experience in large truck crashes, analysis brief.

    Science.gov (United States)

    2017-01-01

    The 2005 Large Truck Crash Causation Study (LTCCS)i was the first-ever national study to attempt to determine the critical reasons and associated factors that contribute to serious large truck crashes. The LTCCS defines critical reason as the r...

  4. 49 CFR 238.219 - Truck-to-car-body attachment.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Truck-to-car-body attachment. 238.219 Section 238.219 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER EQUIPMENT SAFETY STANDARDS Specific Requirements for Tier I Passenger Equipment § 238.219 Truck-to-ca...

  5. 76 FR 40980 - Pilot Program on NAFTA Long-Haul Trucking Provisions

    Science.gov (United States)

    2011-07-12

    ...-0097] Pilot Program on NAFTA Long-Haul Trucking Provisions AGENCY: Federal Motor Carrier Safety... resulting from the implementation of its United States-Mexico cross- border long-haul trucking pilot program. This pilot program is part of FMCSA's implementation of the North American Free Trade Agreement (NAFTA...

  6. Work-related musculoskeletal discomfort among heavy truck drivers.

    Science.gov (United States)

    Nazerian, Ramtin; Korhan, Orhan; Shakeri, Ehsan

    2018-03-13

    Heavy truck drivers are exposed to various psychological, psychosocial and physiological factors, some of which can cause musculoskeletal discomfort in different body regions. This study aims to investigate the correlation between different factors of musculoskeletal discomfort in heavy truck drivers. A cross-sectional study design was applied. A total of 384 participants were interviewed using an updated version of the Nordic musculoskeletal questionnaire. While hypothesis testing was used to assess the association of different factors in musculoskeletal discomfort, logistic regression was applied to explore different correlations among questions of the survey. The results demonstrate that hours of exposure to vibration were associated with discomfort in the neck and shoulders (p  0.05. Fifty-seven percent of the drivers were suffering from discomfort in their lower back region. Moreover, seat comfort was found to be highly correlated with discomfort in the neck, shoulder and upper back areas. Additionally, with aging the likelihood of experiencing discomfort in the neck, upper back and knees is increased.

  7. Urban risks of truck transport of radioactive material

    International Nuclear Information System (INIS)

    Mills, G.S.; Neuhauser, K.S.

    1998-01-01

    Truck transport of radioactive material (RAM), e.g., spent nuclear fuel (SNF), normally maximizes use of Interstate highways, which are safer and more efficient for truck transport in general. In the estimation of transportation risks, population bordering a route is a direct factor in determining consequences and an indirect factor in determining exposure times, accident probabilities and severities, and other parameters. Proposals to transport RAM may draw intense resistance from stakeholders based on concern for population concentrations along urban segments but the length of a route segment is also a determinative factor in estimating the transport risks. To quantify the relative importance of these two factors, a potential route for transport of SNF (strict use of Interstate highways) was selected and compared with a modified version that bypassed urban areas. The RADTRAN 4 code for transportation risk assessment, which was developed at Sandia National Laboratories, was used in the present study to assess the relative risks of SNF transportation for alternative routes. The results suggest that emphasis on Interstate highways minimizes total route and urban segment risks

  8. Study of trends in the trucking market in modern conditions

    Directory of Open Access Journals (Sweden)

    P.Popovych

    2016-08-01

    Full Text Available The article analyzes the features of the transport services market in accordance with its segmentation from the position of statistics on the field of automotive freight. The tendencies of development dynamics and road trucking transport market structure, and particularly the impact of transportation logistics market, including foreign trade cargo traffic of road transport, on the basic trends and the impact of logistics infrastructure development for aggregate indicators of development of transport communications, the size and dynamics of development, market compatibility on investment attractiveness. Balance of consumer, wholesale and logistics market in Ukraine, having similar development trends are established. Market logistics of trucking transport services have a steady trend of development in an objective decline in growth. The necessity of modernization policies in the transport sector at the state level as a software-oriented transport sector investment resources of the economy, taking into account that the share of road transport in the transport system of the country demonstrates the dynamic development with a positive trend in demand for transportation of goods.

  9. Truck Drivers And Risk Of STDs Including HIV

    Directory of Open Access Journals (Sweden)

    Bansal R.K

    1995-01-01

    Full Text Available Research Question: Whether long distance truck drivers are at a higher risk of contracting and transmitting STDs including HIV? Objectives: i To study the degree of knowledge of HIV and AIDS among long- distance truck drivers. ii Assess their sexual behaviour including condom use. iii Explore their prevailing social influences and substance abuse patterns. iv Explore their treatment seeking bahaviour as regards STDs. v Deduce their risk of contracting and transmitting STDs including HIV. Study Design: Cross- sectional interview. Setting: Transport Nagar, Indore (M.P Participants: 210 senior drivers (First drivers and 210 junior drivers (Second drivers. Study Variables: Extra-Marital sexual intercourse, condom usage, past and present history of STDs, treatment and counseling, substance abuse, social â€" cultural milieu. Outcome Variables: Risk of contraction of STDs. Statistical Analysis: Univariate analysis. Results: 94% of the drivers were totally ignorant about AIDS. 82.9% and 43.8 % of the senior and junior drivers had a history of extra- marital sex and of these only 2 regularly used condoms. 13.8% and 3.3 % of the senior and junior drivers had a past or present history suggestive of STD infection. Alcohol and Opium were regularly used by them. Conclusion: The studied drivers are at a high risk of contracting and transmitting STDs including HIV.

  10. Investigation of RADTRAN Stop Model input parameters for truck stops

    International Nuclear Information System (INIS)

    Griego, N.R.; Smith, J.D.; Neuhauser, K.S.

    1996-01-01

    RADTRAN is a computer code for estimating the risks and consequences as transport of radioactive materials (RAM). RADTRAN was developed and is maintained by Sandia National Laboratories for the US Department of Energy (DOE). For incident-free transportation, the dose to persons exposed while the shipment is stopped is frequently a major percentage of the overall dose. This dose is referred to as Stop Dose and is calculated by the Stop Model. Because stop dose is a significant portion of the overall dose associated with RAM transport, the values used as input for the Stop Model are important. Therefore, an investigation of typical values for RADTRAN Stop Parameters for truck stops was performed. The resulting data from these investigations were analyzed to provide mean values, standard deviations, and histograms. Hence, the mean values can be used when an analyst does not have a basis for selecting other input values for the Stop Model. In addition, the histograms and their characteristics can be used to guide statistical sampling techniques to measure sensitivity of the RADTRAN calculated Stop Dose to the uncertainties in the stop model input parameters. This paper discusses the details and presents the results of the investigation of stop model input parameters at truck stops

  11. Italian energy scenarios comparative evaluations

    International Nuclear Information System (INIS)

    Contaldi, Mario

    2005-01-01

    This paper reviews some representative scenarios of the evolution of the Italian primary energy consumption, updated recently. After an overview of the main macroeconomics assumptions the scenario results are cross checked at sectorial level, with a brief discussion of the underlining data and energy intensity trends. The emissions of CO 2 , SO 2 and NO x resulting from the considered scenarios are also reported and discussed [it

  12. Learning from global emissions scenarios

    International Nuclear Information System (INIS)

    O'Neill, Brian C; Nakicenovic, Nebojsa

    2008-01-01

    Scenarios of global greenhouse gas emissions have played a key role in climate change analysis for over twenty years. Currently, several research communities are organizing to undertake a new round of scenario development in the lead-up to the Fifth Assessment Report of the Intergovernmental Panel on Climate Change (IPCC). To help inform this process, we assess a number of past efforts to develop and learn from sets of global greenhouse gas emissions scenarios. We conclude that while emissions scenario exercises have likely had substantial benefits for participating modeling teams and produced insights from individual models, learning from the exercises taken as a whole has been more limited. Model comparison exercises have typically focused on the production of large numbers of scenarios while investing little in assessing the results or the production process, perhaps on the assumption that later assessment efforts could play this role. However, much of this assessment potential remains untapped. Efforts such as scenario-related chapters of IPCC reports have been most informative when they have gone to extra lengths to carry out more specific comparison exercises, but in general these assessments do not have the remit or resources to carry out the kind of detailed analysis of scenario results necessary for drawing the most useful conclusions. We recommend that scenario comparison exercises build-in time and resources for assessing scenario results in more detail at the time when they are produced, that these exercises focus on more specific questions to improve the prospects for learning, and that additional scenario assessments are carried out separately from production exercises. We also discuss the obstacles to better assessment that might exist, and how they might be overcome. Finally, we recommend that future work include much greater emphasis on understanding how scenarios are actually used, as a guide to improving scenario production.

  13. Scenario Planning as Organizational Intervention

    DEFF Research Database (Denmark)

    Balarezo, Jose; Nielsen, Bo Bernhard

    2017-01-01

    Purpose: This paper identifies four areas in need of future research to enhance our theoretical understanding of scenario planning, and sets the basis for future empirical examination of its effects on individual and organizational level outcomes. Design/methodology/approach: This paper organizes...... existing contributions on scenario planning within a new consolidating framework that includes antecedents, processes, and outcomes. The proposed framework allows for integration of the extant literature on scenario planning from a wide variety of fields, including strategic management, finance, human...

  14. The changing nutrition scenario

    Directory of Open Access Journals (Sweden)

    C Gopalan

    2013-01-01

    Full Text Available The past seven decades have seen remarkable shifts in the nutritional scenario in India. Even up to the 1950s severe forms of malnutrition such as kwashiorkar and pellagra were endemic. As nutritionists were finding home-grown and common-sense solutions for these widespread problems, the population was burgeoning and food was scarce. The threat of widespread household food insecurity and chronic undernutrition was very real. Then came the Green Revolution. Shortages of food grains disappeared within less than a decade and India became self-sufficient in food grain production. But more insidious problems arising from this revolution were looming, and cropping patterns giving low priority to coarse grains and pulses, and monocropping led to depletion of soil nutrients and ′Green Revolution fatigue′. With improved household food security and better access to health care, clinical manifestations of severe malnutrition virtually disappeared. But the decline in chronic undernutrition and "hidden hunger" from micronutrient deficiencies was slow. On the cusp of the new century, an added factor appeared on the nutritional scene in India. With steady urban migration, upward mobility out of poverty, and an increasingly sedentary lifestyle because of improvements in technology and transport, obesity rates began to increase, resulting in a dual burden. Measured in terms of its performance in meeting its Millennium Development Goals, India has fallen short. Despite its continuing high levels of poverty and illiteracy, India has a huge demographic potential in the form of a young population. This advantage must be leveraged by investing in nutrition education, household access to nutritious diets, sanitary environment and a health-promoting lifestyle. This requires co-operation from all the stakeholders, including governments, non government organizations, scientists and the people at large.

  15. The changing nutrition scenario.

    Science.gov (United States)

    Gopalan, C

    2013-09-01

    The past seven decades have seen remarkable shifts in the nutritional scenario in India. Even up to the 1950s severe forms of malnutrition such as kwashiorkar and pellagra were endemic. As nutritionists were finding home-grown and common-sense solutions for these widespread problems, the population was burgeoning and food was scarce. The threat of widespread household food insecurity and chronic undernutrition was very real. Then came the Green Revolution. Shortages of food grains disappeared within less than a decade and India became self-sufficient in food grain production. But more insidious problems arising from this revolution were looming, and cropping patterns giving low priority to coarse grains and pulses, and monocropping led to depletion of soil nutrients and 'Green Revolution fatigue'. With improved household food security and better access to health care, clinical manifestations of severe malnutrition virtually disappeared. But the decline in chronic undernutrition and "hidden hunger" from micronutrient deficiencies was slow. On the cusp of the new century, an added factor appeared on the nutritional scene in India. With steady urban migration, upward mobility out of poverty, and an increasingly sedentary lifestyle because of improvements in technology and transport, obesity rates began to increase, resulting in a dual burden. Measured in terms of its performance in meeting its Millennium Development Goals, India has fallen short. Despite its continuing high levels of poverty and illiteracy, India has a huge demographic potential in the form of a young population. This advantage must be leveraged by investing in nutrition education, household access to nutritious diets, sanitary environment and a health-promoting lifestyle. This requires co-operation from all the stakeholders, including governments, non government organizations, scientists and the people at large.

  16. Penentuan Umur Ekonomis Dump Truck Dengan Menggunakan Metode Biaya Tahunan Rata-Rata Pada PTPN 3 PKS Kebun Rambutan

    OpenAIRE

    Mazmur Harapanta Tarigan

    2009-01-01

    PTPN 3 PKS Kebun Rambutan merupakan perusahaan yang bergerak di bidang pengolahan minyak sawit Crude Palm Oil dan inti sawit Palm Kernel. Kerusakan Dump Truck merupakan salah satu faktor penyebab terganggunya kelancaran produksi. Kerusakan pada Dump Truck tidak dapat ditentukan dengan pasti, hanya dapat diperkirakan dengan menentukan umur ekonomis Dump Truck tersebut. Alat pengangkut yang dibahas dalam penelitian ini adalah Dump Truck. Pokok permasalahan dari penelitian ini adalah untuk m...

  17. Millennium Ecosystem Assessment: MA Scenarios

    Data.gov (United States)

    National Aeronautics and Space Administration — The Millennium Ecosystem Assessment: MA Scenarios provide useful insight into the complex factors that drive ecosystem change, estimating the magnitude of regional...

  18. Automated Analysis of Infinite Scenarios

    DEFF Research Database (Denmark)

    Buchholtz, Mikael

    2005-01-01

    The security of a network protocol crucially relies on the scenario in which the protocol is deployed. This paper describes syntactic constructs for modelling network scenarios and presents an automated analysis tool, which can guarantee that security properties hold in all of the (infinitely many......) instances of a scenario. The tool is based on control flow analysis of the process calculus LySa and is applied to the Bauer, Berson, and Feiertag protocol where is reveals a previously undocumented problem, which occurs in some scenarios but not in other....

  19. Occupational Hydrofluoric Acid Injury from Car and Truck Washing--Washington State, 2001-2013.

    Science.gov (United States)

    Reeb-Whitaker, Carolyn K; Eckert, Carly M; Anderson, Naomi J; Bonauto, David K

    2015-08-21

    Exposure to hydrofluoric acid (HF) causes corrosive chemical burns and potentially fatal systemic toxicity. Car and truck wash cleaning products, rust removers, and aluminum brighteners often contain HF because it is efficient in breaking down roadway matter. The death of a truck wash worker from ingestion of an HF-based wash product and 48 occupational HF burn cases associated with car and truck washing in Washington State during 2001-2013 are summarized in this report. Among seven hospitalized workers, two required surgery, and all but one worker returned to the job. Among 48 injured workers, job titles were primarily auto detailer, car wash worker, truck wash worker, and truck driver. Because HF exposure can result in potentially severe health outcomes, efforts to identify less hazardous alternatives to HF-based industrial wash products are warranted.

  20. National Survey of US Long-Haul Truck Driver Health and Injury: health behaviors.

    Science.gov (United States)

    Birdsey, Jan; Sieber, W Karl; Chen, Guang X; Hitchcock, Edward M; Lincoln, Jennifer E; Nakata, Akinori; Robinson, Cynthia F; Sweeney, Marie H

    2015-02-01

    To compare selected health behaviors and body mass index (modifiable risk factors) of US long-haul truck drivers to the US working population by sex. The National Survey of US Long-Haul Truck Driver Health and Injury interviewed a nationally representative sample of long-haul truck drivers (n = 1265) at truck stops. Age-adjusted results were compared with national health surveys. Compared with US workers, drivers had significantly higher body mass index, current cigarette use, and pack-years of smoking; lower prevalence of annual influenza vaccination; and generally lower alcohol consumption. Physical activity level was low for most drivers, and 25% had never had their cholesterol levels tested. Working conditions common to long-haul trucking may create significant barriers to certain healthy behaviors; thus, transportation and health professionals should address the unique work environment when developing interventions for long-haul drivers.

  1. Technology Roadmap for the 21st Century Truck Program, a government-industry research partnership

    Energy Technology Data Exchange (ETDEWEB)

    None

    2000-12-01

    The 21st Century Truck Program has been established as a government-industry research partnership to support the development and implementation of commercially viable technologies that will dramatically cut fuel use and emissions of commercial trucks and buses while enhancing their safety and affordability as well as maintaining or enhancing performance. The innovations resulting from this program will reduce dependence on foreign oil, improve our nation's air quality, provide advanced technology for military vehicles, and enhance the competitiveness of the U.S. truck and bus industry while ensuring safe and affordable freight and bus transportation for the nation's economy. This Technology Roadmap for the 21st Century Truck Program has been prepared to guide the development of the technical advancements that will enable the needed improvements in commercial truck fuel economy, emissions, and safety.

  2. Analysis of major trends in U.S. commercial trucking, 1977-2002.

    Energy Technology Data Exchange (ETDEWEB)

    Bertram, K. M.; Santini, D .J.; Vyas, A. D.

    2009-06-10

    This report focuses on various major long-range (1977-2002) and intermediate-range (1982-2002) U.S. commercial trucking trends. The primary sources of data for this period were the U.S. Bureau of the Census Vehicle Inventory and Use Survey and Truck Inventory and Use Survey. In addition, selected 1977-2002 data from the U.S. Department of Energy/Energy Information Administration and from the U.S. Department of Transportation/Federal Highway Administration's Highway Statistics were used. The report analyzes (1) overall gasoline and diesel fuel consumption patterns by passenger vehicles and trucks and (2) the population changes and fuels used by all commercial truck classes by selected truck type (single unit or combination), during specified time periods, with cargo-hauling commercial trucks given special emphasis. It also assesses trends in selected vehicle miles traveled, gallons per vehicle miles traveled, and gallons per cargo ton-mile traveled, as well as the effect of cargo tons per truck on fuel consumption. In addition, the report examines long-range trends for related factors (e.g., long-haul mileages driven by heavy trucks) and their impacts on reducing fuel consumption per cargo-ton-mile and the relative shares of total commercial fuel use among truck classes. It identifies the effects of these trends on U.S. petroleum consumption. The report also discusses basic engineering design and performance, national legislation on interstate highway construction, national demographic trends (e.g., suburbanization), and changes in U.S. corporate operations requirements, and it highlights their impacts on both the long-distance hauling and shorter-distance urban and suburban delivery markets of the commercial trucking industry.

  3. Vehicle to Grid regulation services of electric delivery trucks: Economic and environmental benefit analysis

    International Nuclear Information System (INIS)

    Zhao, Yang; Noori, Mehdi; Tatari, Omer

    2016-01-01

    Highlights: • Potential net present revenues of electric truck based V2G regulation services are investigated. • GHG emission mitigation of V2G regulation services provided by electric trucks are quantified. • The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed. • V2G regulation services for electric trucks could yield considerable revenues and GHG emission savings. - Abstract: Concerns regarding the fuel costs and climate change impacts associated with petroleum combustion are among the main driving factors for the adoption of electric vehicles. Future commercial delivery truck fleets may include Battery Electric Vehicles (BEVs) and Extended Range Electric Vehicles (EREVs); in addition to savings on fuel and maintenance costs, the introduction of these grid accessible electric vehicles will also provide fleet owners with possible Vehicle to Grid (V2G) opportunities. This study investigates the potential net present revenues and greenhouse gas (GHG) emission mitigation of V2G regulation services provided by electric trucks in a typical fleet. The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed and compared to those of traditional diesel trucks. To account for uncertainties, possible ranges for key parameters are considered instead of only considering fixed single data values for each parameter. The results of this research indicate that providing V2G regulation services for electric trucks could yield considerable additional revenues ($20,000–50,000) and significant GHG emission savings (approximately 300 ton CO 2 ) compared to conventional diesel trucks.

  4. Scenario Planning and Collection Development.

    Science.gov (United States)

    Giesecke, Joan

    1999-01-01

    Discussion of the future of library collection development and the need for planning focuses on the technique of scenario planning and discusses the results of scenario planning at the University of NebraskaLincoln that examined collection development and digital information. (LRW)

  5. Application Scenarios and Deployment Domains

    NARCIS (Netherlands)

    Niamut, O.A.; Engström, A.; Kochale, A.; Macq, J.; Thomas, G.; Zorić, G.

    2014-01-01

    This chapter describes the impact of deploying the format-agnostic media approach, along the lines of three deployment domains and the end user perspective. The chapter elaborates on a series of potential application scenarios. These application scenarios describe features of a potential

  6. Potential air toxics hot spots in truck terminals and cabs.

    Science.gov (United States)

    Smith, Thomas J; Davis, Mary E; Hart, Jaime E; Blicharz, Andrew; Laden, Francine; Garshick, Eric

    2012-12-01

    Hot spots are areas where concentrations of one or more air toxics--organic vapors or particulate matter (PM)--are expected to be elevated. The U.S. Environmental Protection Agency's (EPA*) screening values for air toxics were used in our definition of hot spots. According to the EPA, a screening value "is used to indicate a concentration of a chemical in the air to which a person could be continually exposed for a lifetime ... and which would be unlikely to result in a deleterious effect (either cancer or noncancer health effects)" (U.S. EPA 2006). Our characterization of volatile organic compounds (VOCs; namely 18 hydrocarbons, methyl tert-butyl ether [MTBE], acetone, and aldehydes) was added onto our ongoing National Cancer Institute-funded study of lung cancer and particulate pollutant concentrations (PM with an aerodynamic diameter highways. In Phase 1 of our study, 15 truck terminals across the United States were each visited for five consecutive days. During these site visits, sorbent tubes were used to collect 12-hour integrated samples of hydrocarbons and aldehydes from upwind and downwind fence-line locations as well as inside truck cabs. Meteorologic data and extensive site information were collected with each sample. In Phase 2, repeat visits to six terminals were conducted to test the stability of concentrations across time and judge the representativeness of our previous measurements. During the repeat site visits, the sampling procedure was expanded to include real-time sampling for total hydrocarbon (HC) and PM2.5 at the terminal upwind and downwind sites and inside the truck cabs, two additional monitors in the yard for four-quadrant sampling to better characterize the influence of wind, and indoor sampling in the loading dock and mechanic shop work areas. Mean and median concentrations of VOCs across the sampling locations in and around the truck terminals showed significant variability in the upwind concentrations as well as in the intensity of

  7. Clean Diesel Engine Component Improvement Program Diesel Truck Thermoelectric Generator

    Energy Technology Data Exchange (ETDEWEB)

    Elsner, N. B. [Hi-Z Technology, Inc., San Diego, CA (United States); Bass, J. C. [Hi-Z Technology, Inc., San Diego, CA (United States); Ghamaty, S. [Hi-Z Technology, Inc., San Diego, CA (United States); Krommenhoek, D. [Hi-Z Technology, Inc., San Diego, CA (United States); Kushch, A. [Hi-Z Technology, Inc., San Diego, CA (United States); Snowden, D. [Hi-Z Technology, Inc., San Diego, CA (United States); Marchetti, S. [Hi-Z Technology, Inc., San Diego, CA (United States)

    2005-03-16

    Hi-Z Technology, Inc. (Hi-Z) is currently developing four different auxiliary generator designs that are used to convert a portion (5 to 20%) of the waste heat from vehicle engines exhaust directly to electricity. The four designs range from 200 Watts to 10 kW. The furthest along is the 1 kW Diesel Truck Thermoelectric Generator (DTTEG) for heavy duty Class 8 Diesel trucks, which, under this program, has been subjected to 543,000 equivalent miles of bouncing and jarring on PACCAR's test track. Test experience on an earlier version of the DTTEG on the same track showed the need for design modifications incorporated in DTTEG Mod 2, such as a heavy duty shock mounting system and reinforcement of the electrical leads mounting system, the thermocouple mounting system and the thermoelectric module restraints. The conclusion of the 543,000 mile test also pointed the way for an upgrading to heavy duty hose or flex connections for the internal coolant connections for the TEG, and consideration of a separate lower temperature cooling loop with its own radiator. Fuel savings of up to $750 per year and a three to five year payback are believed to be possible with the 5 % efficiency modules. The economics are expected to improve considerably to approach a two year payback when the 5 kW to 10 kW generators make it to the market in a few years with a higher efficiency (20%) thermoelectric module system called Quantum Wells, which are currently under development by Hi-Z. Ultimately, as automation takes over to reduce material and labor costs in the high volume production of QW modules, a one year payback for the 5 kW to10 kW generator appears possible. This was one of the stated goals at the beginning of the project. At some future point in time, with the DTTEG becoming standard equipment on all trucks and automobiles, fuel savings from the 25% conversion of exhaust heat to useable electricity nationwide equates to a 10% reduction in the 12 to 15 million barrels per day of

  8. Combined Aero and Underhood Thermal Analysis for Heavy Duty Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Vegendla, Prasad [Argonne National Lab. (ANL), Argonne, IL (United States); Sofu, Tanju [Argonne National Lab. (ANL), Argonne, IL (United States); Saha, Rohit [Cummins Inc., Columbus, IN (United States); Madurai Kumar, Mahesh [Cummins Inc., Columbus, IN (United States); Hwang, L. K [Cummins Inc., Columbus, IN (United States)

    2017-01-31

    Aerodynamic analysis of the medium-duty delivery truck was performed to achieve vehicle design optimization. Three dimensional CFD simulations were carried out for several improved designs, with a detailed external component analysis of wheel covers, side skirts, roof fairings, and rounded trailer corners. The overall averaged aerodynamics drag reduction through the design modifications were shown up to 22.3% through aerodynamic considerations alone, which is equivalent to 11.16% fuel savings. The main identified fuel efficiencies were based on second generation devices, including wheel covers, side skirts, roof fairings, and rounded trailer corners. The important findings of this work were; (i) the optimum curvature radius of the rounded trailer edges found to be 125 mm, with an arc length of 196.3 mm, (ii) aerodynamic drag reduction increases with dropping clearance of side skirts between wheels and ground, and (iii) aerodynamic drag reduction increases with an extension of front bumper towards the ground.

  9. Comparing Gravimetric and Real-Time Sampling of PM2.5 Concentrations Inside Truck Cabins

    Science.gov (United States)

    Zhu, Ying; Smith, Thomas J.; Davis, Mary E.; Levy, Jonathan I.; Herrick, Robert; Jiang, Hongyu

    2012-01-01

    As part of a study on truck drivers’ exposure and health risk, pickup and delivery (P&D) truck drivers’ on-road exposure patterns to PM2.5 were assessed in five weeklong sampling trips in metropolitan areas of five U.S. cities from April to August of 2006. Drivers were sampled with real-time (DustTrak) and gravimetric samplers to measure average in-cabin PM2.5 concentrations and to compare their correspondence in moving trucks. In addition, GPS measurements of truck locations, meteorological data, and driver behavioral data were collected throughout the day to determine which factors influence the relationship between real-time and gravimetric samplers. Results indicate that the association between average real-time and gravimetric PM2.5 measurements on moving trucks was fairly consistent (Spearman rank correlation of 0.63), with DustTrak measurements exceeding gravimetric measurements by approximately a factor of 2. This ratio differed significantly only between the industrial Midwest cities and the other three sampled cities scattered in the South and West. There was also limited evidence of an effect of truck age. Filter samples collected concurrently with DustTrak measurements can be used to calibrate average mass concentration responses for the DustTrak, allowing for real-time measurements to be integrated into longer-term studies of inter-city and intra-urban exposure patterns for truck drivers. PMID:21991940

  10. Comparing gravimetric and real-time sampling of PM(2.5) concentrations inside truck cabins.

    Science.gov (United States)

    Zhu, Ying; Smith, Thomas J; Davis, Mary E; Levy, Jonathan I; Herrick, Robert; Jiang, Hongyu

    2011-11-01

    As part of a study on truck drivers' exposure and health risk, pickup and delivery (P&D) truck drivers' on-road exposure patterns to PM(2.5) were assessed in five, weeklong sampling trips in metropolitan areas of five U.S. cities from April to August of 2006. Drivers were sampled with real-time (DustTrak) and gravimetric samplers to measure average in-cabin PM(2.5) concentrations and to compare their correspondence in moving trucks. In addition, GPS measurements of truck locations, meteorological data, and driver behavioral data were collected throughout the day to determine which factors influence the relationship between real-time and gravimetric samplers. Results indicate that the association between average real-time and gravimetric PM(2.5) measurements on moving trucks was fairly consistent (Spearman rank correlation of 0.63), with DustTrak measurements exceeding gravimetric measurements by approximately a factor of 2. This ratio differed significantly only between the industrial Midwest cities and the other three sampled cities scattered in the South and West. There was also limited evidence of an effect of truck age. Filter samples collected concurrently with DustTrak measurements can be used to calibrate average mass concentration responses for the DustTrak, allowing for real-time measurements to be integrated into longer-term studies of inter-city and intra-urban exposure patterns for truck drivers.

  11. Design and analysis of truck body for increasing the payload capacity

    Science.gov (United States)

    Vamshi Krishna, K.; Yugandhar Reddy, K.; Venugopal, K.; Ravi, K.

    2017-11-01

    Truck industry is a major source of transportation in India. With an average truck travelling about 300 kilometers per day [1], every kilogram of truck weight is of concern to the industry in order to get the best out of the truck. The main objective of this project is to increase the payload capacity of automotive truck body. Every kilogram of increased vehicle weight will decrease the vehicle payload capacity in turn increasing the manufacturing cost and reducing the fuel economy by increase the fuel consumption. With the intension of weight reduction, standard truck body has been designed and analyzed in ANSYS software. C-cross section beams were used instead of conventional rectangular box sections to reduce the weight of the body. Light-weight Aluminum alloy Al 6061 T6 is used to increase the payload capacity. The strength of the Truck platform is monitored in terms of deformation and stress concentration. These parameters will be obtained in structural analysis test condition environment. For reducing the stress concentration the concept of beams of uniform strength is used. Accordingly necessary modifications are done so that the optimized model has a better stress distribution and much lesser weight compared to the conventional model. The results obtained by analyzing the modified model are compared with the standard model.

  12. Development of Diesel Engine Operated Forklift Truck for Explosive Gas Atmospheres

    Science.gov (United States)

    Vishwakarma, Rajendra Kumar; Singh, Arvind Kumar; Ahirwal, Bhagirath; Sinha, Amalendu

    2018-02-01

    For the present study, a prototype diesel engine operated Forklift truck of 2 t capacity is developed for explosive gas atmosphere. The parts of the Forklift truck are assessed against risk of ignition of the explosive gases, vapors or mist grouped in Gr. IIA and having ignition temperature more than 200°C. Identification of possible sources of ignition and their control or prevention is the main objective of this work. The design transformation of a standard Forklift truck into a special Forklift truck is made on prototype basis. The safety parameters of the improved Forklift truck are discussed in this paper. The specially designed Forklift truck is useful in industries where explosive atmospheres may present during normal working conditions and risk of explosion is a concern during handling or transportation of materials. This indigenous diesel engine based Forklift truck for explosive gas atmosphere classified as Zone 1 and Zone 2 area and gas group IIA is developed first time in India in association with the Industry.

  13. Two death cases originating from supplementary heater in the cabins of parked trucks.

    Science.gov (United States)

    Demirci, Serafettin; Dogan, Kamil Hakan; Erkol, Zerrin; Gunaydin, Gursel

    2009-02-01

    A supplementary heater can be mounted in trucks or other transportation vehicles and used to heat the air in the cabin independent of the engine of the vehicle. This apparatus works with diesel fuel or gasoline. Combustion products burning in the pre-combustion chamber heat the fins of the engine. The air passing through the fins is heated and is transferred into the cabin. The malfunction of such an apparatus may be the cause of carbon monoxide (CO) poisoning or fire. In this study, we report two cases in which drivers died while asleep in the cabins of parked trucks. In the first case, a 43-year-old man died because of CO poisoning originating from a broken supplementary heater. In the second case, a 48-year-old man died owing to a fire that resulted from the burning of upholstery cloths in the truck cabin, and which was caused by a supplementary heater set at very high temperatures. In both cases, it was determined by a technical expert that the CO poisoning in the first case and the fire in the second case were caused by the supplementary heater in the trucks. It is emphasized in this article that the supplementary heater in the truck might be the cause of mortal CO poisoning as well as be responsible for fires in the cabins of the trucks. It aims to highlight that a detailed investigation of supplementary heaters at the death scene is required for such death cases in the trucks.

  14. Truck acceleration behavior study and acceleration lane length recommendations for metered on-ramps

    Directory of Open Access Journals (Sweden)

    Guangchuan Yang

    2016-10-01

    Full Text Available This paper investigated the actual truck acceleration capability at metered on-ramps. Truck acceleration performance data were collected through a video-based data collection method. A piecewise constant acceleration model was employed to capture truck acceleration characteristics. It was found that the existing acceleration length will affect truck drivers’ acceleration behavior. At the taper type ramp that has limited acceleration distance, acceleration profile indicated a decreasing trend with distance. While for the ramp with an auxiliary lane that has sufficient acceleration distance, it was found that the acceleration behavior is to have a high acceleration rate in the beginning, then acceleration rate decrease with speed increase, and high acceleration rate again as drivers approach the merging area. Field data show that the truck acceleration performance data documented in the ITE’s (Institute of Transportation Engineers “Traffic Engineering Handbook” are much lower than the field collected data. Also, based on the regression analysis of speed versus distance profiles, it was found that the AASHTO’s (American Association of State Highway and Transportation Officials Green Book acceleration length design guidance is insufficient to accommodate trucks at metered on-ramps. The required acceleration lengths for medium and heavy trucks are approximately 1.3 and 1.6 times of the Green Book design guideline, respectively.

  15. A Clinical Trial on Weight Loss among Truck Drivers

    Directory of Open Access Journals (Sweden)

    MS Thiese

    2015-04-01

    Full Text Available Background: The high prevalence of obesity among commercial truck drivers may be related to sedentary nature of the job, lack of healthy eating choices, and lack of exercise. There may be a link between obesity and crash risk, therefore an intervention to reduce obesity in this population is needed. Objective: To assess feasibility of a 12-week weight loss intervention for truck drivers with a weight loss goal of 10% of initial body weight. Methods: Drivers were selected based on age (≥21 years and body mass index (≥30 kg/m2. The drivers participated in a before-after clinical trial. The intervention included a 12-week program that provided information on healthy diet and increasing exercise, and telephone-based coaching using SMART goals. Outcomes included change from baseline in reported energy intake, measured weight, waist, hip, and neck circumference, blood pressure, and point of care capillary blood lipids and hemoglobin A1c. Exit interviews were conducted to gain insight into driver opinions on the program features and usefulness. This study was registered with the NIH Clinical Trials Registry, number NCT02348983. Results: 12 of 13 drivers completed the study. Weight loss was statistically significant (p=0.03. Reported energy (p=0.005, total fat consumption (p=0.04, and saturated fat consumption (p=0.02 intake were also lower after the 12-week intervention. Drivers attributed their weight loss to health coaching and suggested a longer intervention so that they could reach their goal and become accustomed to the changes. Conclusion: This weight loss intervention is feasible for this difficult population. Additional research is needed to compare this intervention with a control group.

  16. The design and implementation of a garbage truck fleet management system

    Directory of Open Access Journals (Sweden)

    Chen, C. H.

    2016-05-01

    Full Text Available In recent years, the improvement of cloud computing and mobile computing techniques has led to the availability of a variety of mobile applications (‘apps’ in the app store. For instance, a garbage truck app that can provide the immediate location of a garbage truck, the location of collection points, and forecasted arrival times of garbage trucks would be useful for mobile users. Since the power consumption of apps on mobile devices if of concern to mobile users, an optimised power-saving mechanism for updating messages, which is based on location information, for a proposed garbage truck fleet management system (GTFMS is proposed and implemented in this paper. The GTFMS is a three- component system that includes the on-board units on garbage trucks, a fleet management system, and a garbage truck app. In this study, an arrival time forecasting method is designed and implemented in the fleet management system, so that the garbage truck app can retrieve the forecasted arrival time via web services. A message updating event is then triggered that reports the location of garbage truck and the forecasted arrival time. In experiments conducted on case studies, the results showed that the mean accuracy of predicted arrival time by the proposed method is about 81.45 per cent. As for power consumption, the cost of traditional mobile apps is 2,880 times that of the mechanism proposed in this study. Consequently, the GTFMS can provide the precise forecasted arrival time of garbage trucks to mobile users, while consuming less power.

  17. Social Foundation of Scenario Planning

    DEFF Research Database (Denmark)

    Rowland, Nicholas James; Spaniol, Matthew Jon

    2017-01-01

    from science and technology studies (STS) on knowledge production, the authors explain transition from one phase to the next and iteration between and within phases based on social negotiation. To this end, the authors examine the interplay between the “scenario development” phase and the “scenario use......” phase of a planning process with a non-governmental organization in Denmark. The upshot for facilitators is practical insight into how transition between phases and phase iteration in scenario planning can be identified, leveraged, and, thus, managed. The upshot for scholars is a related insight...

  18. A dynamic binaural synthesis system for investigation into situational awareness for truck drivers

    DEFF Research Database (Denmark)

    Christensen, Flemming; Møller, Anders Kalsgaard; Hammershøi, Dorte

    2016-01-01

    binaural synthesis system for investigation into situational awareness for truck drivers. The system is built around several software components enabling the 3D positioning of an auditory representation of a bicycle. The sound is played back over headphones to the truck driver whose head movements...... communicating over a network protocol (UDP) enabling distribution on several hardware devices. The modules are: Graphical user interface, head tracking server, truck tracking, and binaural synthesis module. The function of the individual modules as well as overall topology of the system will be presented...

  19. APPLICATION OF MSC ADAMS – NX NASTRAN/FEMAP INTERFACE IN STRENGTH CALCULATIONS OF TRUCK FRAMES

    Directory of Open Access Journals (Sweden)

    Adam PRZEMYK

    2016-06-01

    Full Text Available In this paper, the finite element method (FEM is used to calculate the strength of truck frames by integrating the MSC Adams software, for dynamics analysis of mechanical systems, and the NX Nastran/Femap software. At the same time, a method for reducing degrees of freedom is been developed based on the Craig–Bampton method. The interface is applied in order to calculate the strength of the frame in the selected truck, which runs on the test track. The selected model of truck can be treated as the virtual prototype that is useful in the design process.

  20. Driving an Industry: Medium and Heavy Duty Fuel Cell Electric Truck Component Sizing

    Energy Technology Data Exchange (ETDEWEB)

    Kast, James; Marcinkoski, Jason; Vijayagopal, Ram; Duran, Adam

    2016-06-22

    Medium and heavy duty (MD and HD respectively) vehicles are responsible for 26 percent of the total U.S. transportation petroleum consumption [1]. Hydrogen fuel cells have demonstrated value as part of a portfolio of strategies for reducing petroleum use and emissions from MD and HD vehicles. [2] [3], but their performance and range capabilities, and associated component sizing remain less clear when compared to other powertrains. This paper examines the suitability of converting a representative sample of MD and HD diesel trucks into Fuel Cell Electric Trucks (FCETs), while ensuring the same truck performance, in terms of range, payload, acceleration, speed, gradeability and fuel economy.

  1. Alternative-fueled truck demonstration natural gas program: Caterpillar G3406LE development and demonstration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    In 1990, the California Energy Commission, the South Coast Air Quality Management District, and the Southern California Gas Company joined together to sponsor the development and demonstration of compressed natural gas engines for Class 8 heavy-duty line-haul trucking applications. This program became part of an overall Alternative-Fueled Truck Demonstration Program, with the goal of advancing the technological development of alternative-fueled engines. The demonstration showed natural gas to be a technically viable fuel for Class 8 truck engines.

  2. Technical documentation for the 1990 Nationwide Truck Activity and Commodity Survey Public Use File

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    The Nationwide Truck Activity and Commodity Survey (NTACS) provides detailed activity data for a sample of trucks covered in the 1987 Truck Inventory and Use Survey (TIUS) for days selected at random over a 12-month period ending in 1990. The NTACS was conducted by the US Bureau of the Census for the US Department of Transportation (DOT). A Public Use File for the NTACS was developed by Oak Ridge National Laboratory (ORNL) under a reimbursable agreement with the DOT. The content of the Public Use File and the design of the NTACS are described in this document.

  3. Black carbon emissions from trucks and trains in the Midwestern and Northeastern United States from 1977 to 2007

    Science.gov (United States)

    Brown-Steiner, Benjamin; Hess, Peter; Chen, Jialie; Donaghy, Kieran

    2016-03-01

    We have developed a framework to estimate BC emissions from heavy-duty diesel trucks and trains engaged in transporting freight in the Midwestern and Northeastern United States (MNUS) from 1977 to 2007. We first expand on a previous development of a regional econometric input-output model (REIM) that has been used to estimate commodity flows between 13 states in the MNUS (plus the rest of the US) and 13 industrial sectors. These commodity flow data are then distributed over the MNUS using a stylized link-and-node network, which creates great circle transportation links between nodes in each state at the county with the largest population. Freight flows are converted to BC transportation emissions and the resulting BC emissions are compared to the MACCity BC emissions inventory. We find that from 1977 to 2007 potential emission growth from the continued increase in freight tonnage in the MWUS is counteracted by decreases in the BC emission factor of heavy-duty diesel trucks, which results in an overall decrease of BC emissions by 2007. One sector (fabricated metal product manufacturing) has dominated the BC transportation emissions throughout 1977 to 2007 with transportation emissions remaining relatively unchanged from 1977 to 1997 and then decreasing out to 2007. The BC transportation emissions are concentrated in and around the urban centers, which serve as transportation and production nodes for industrial manufacturing. Our BC emissions are distributed along stylized transportation corridors that are not well represented in emissions inventories that largely distribute emissions via a population proxy. The framework established in this study can be used to estimate future BC transportation emissions under a set of stylized economic, technological, and regulatory scenarios.

  4. The association between adolescent entry into the trucking industry and risk of HIV among long-distance truck drivers in India.

    Science.gov (United States)

    Mishra, Ram Manohar; Dube, Madhulika; Saggurti, Niranjan; Pandey, Arvind; Mahapatra, Bidhubhusan; Ramesh, Sowmya

    2012-01-01

    This study examines the relationship between entry into the trucking industry during adolescence and both sexually transmitted infections (STIs) and infection by the human immunodeficiency virus (HIV) among long-distance truck drivers in India. Data were sourced from a cross-sectional survey (sample size: 2066) undertaken in 2007 among long-distance truck drivers. The survey spread across major transshipment locations covering the bulk of India's transport volume along four routes. Participants were interviewed about sexual behaviors and were tested for HIV and STIs. The present authors constructed two synthetic cohorts based on the participants' duration of employment in the trucking industry: (1) low (duration ≤ 6 years) and (2) high experience (duration ≥ 7 years). Based on age at entry into the trucking industry, participants were termed as either adolescent (age at entry 4.0%, respectively; adjusted OR: 1.9; 95% CI: 1.2-3.1) and syphilis (5.7% versus 3.5%, respectively; adjusted OR: 1.8; 95% CI: 1.1-3.1). These results suggest the need for focused behavioral change programs in HIV prevention interventions for adolescent truckers in India and elsewhere.

  5. Scenario Based Network Infrastructure Planning

    DEFF Research Database (Denmark)

    Knudsen, Thomas Phillip; Pedersen, Jens Myrup; Madsen, Ole Brun

    2005-01-01

    The paper presents a method for IT infrastructure planning that take into account very long term developments in usages. The method creates a scenario for a final, time independent stage in the planning process. The method abstracts relevant modelling factors from available information......; this includes available statistical information and a short survey of emerging technologies. A scenario for Denmark is presented and consequences are discussed....

  6. Le metodologie dello scenario parecipato

    DEFF Research Database (Denmark)

    Rasmussen, Lauge Baungaard

    2006-01-01

    The article presents paradigm, historical background and framework of participatory scenario planning. In addition an example of the method used in Malaysia is described and the possible strenghts and weaknesses is reflected......The article presents paradigm, historical background and framework of participatory scenario planning. In addition an example of the method used in Malaysia is described and the possible strenghts and weaknesses is reflected...

  7. Italian energy scenarios: Markal model

    International Nuclear Information System (INIS)

    Gracceva, Francesco

    2005-01-01

    Energy scenarios carried out through formal models comply with scientific criteria such as internal coherence and transparency. Besides, Markal methodology allows a good understanding of the complex nature of the energy system. The business-as-usual scenario carried out through the Markal-Italy model shows that structural changes occurring in end-use sectors will continue to drive up energy consumption, in spite of the slow economic growth and the quite high energy prices [it

  8. Using truck fleet data in combination with other data sources for freight modeling and planning : [summary].

    Science.gov (United States)

    2014-07-01

    Freight- carrying truck traffic is common on : Florida highways. This traffic has been increasing : steadily for many years with ever more impacts : on highway efficiency and safety and damage to : highways. Reducing the efficient movement of : traff...

  9. DYNAMIC ANALYSIS OF HYDRAULIC DRIVE OF TILTING PLATFORM MECHANISM OF DUMP TRUCK

    Directory of Open Access Journals (Sweden)

    P. Kishkevich

    2011-01-01

    Full Text Available Object of research – hydraulic drive of tilting platform mechanism of dump truck. We pro-pose a dynamic model of the hydraulic system. The model takes into account the cyclic operation (lifting, lowering the platform.

  10. DYNAMIC ANALYSIS OF HYDRAULIC DRIVE OF TILTING PLATFORM MECHANISM OF DUMP TRUCK

    OpenAIRE

    P. Kishkevich; A. Safonau; I. Selivonchik; P. Bartosh

    2011-01-01

    Object of research – hydraulic drive of tilting platform mechanism of dump truck. We pro-pose a dynamic model of the hydraulic system. The model takes into account the cyclic operation (lifting, lowering the platform).

  11. Effect of freeway level of service and driver education on truck driver stress : phase 1.

    Science.gov (United States)

    2012-08-01

    This research primarily deals with truck driver stress and its nature, stressors, and their mutual relationship. During the : study, the different demands of driving that are related to roads, vehicle, traffic conditions, driver predisposition to : s...

  12. Tracking truck flows with programmable mobile devices for drayage efficiency analysis : final report.

    Science.gov (United States)

    2016-05-01

    Inefficient use of drayage trucks results in negative externalities in the form of pollution and congestion. A clear : awareness of the current state of drayage efficiency is especially important in Southern California since the cargo : volume at the...

  13. Automated low-cost and real-time truck parking information system.

    Science.gov (United States)

    2013-11-01

    In this project an automated real-time parking information system was developed to improve : truck-parking safety through efficient gathering and disseminating information regarding the use : of existing parking capacity. The system consists of four ...

  14. Structural health monitoring of highway bridges subjected to overweight trucks, phase I - instrumentation development and validation.

    Science.gov (United States)

    2016-01-01

    State departments of transportation (DOTs) in the west have been under increasing pressure to permit and route overweight trucks transporting machinery and equipment for the energy sector through their state and interstate highway systems. DOT engine...

  15. Using 3D Multi-Body Simulation to Evaluate Future Truck Technologies

    National Research Council Canada - National Science Library

    Gunter, Dave; Bylsma, Wes; Letherwood, Mike; Dennis, Stacey; Argeropoulos, Kris; Teschendorf, Dan; Gorsich, Dave

    2004-01-01

    ... steering, and in-hub electric drive motors. Fully three-dimensional Future Truck models were created using a commercially available modeling and simulation methodology and limited validation studies were performed by comparing model...

  16. Process for evaluating overweight truck corridors serving coastal port regions and border ports of entry

    Science.gov (United States)

    2017-08-01

    Coastal and inland ports, regional mobility authorities, cities, and counties located near or along the Texas Gulf Coast, and along the border with Mexico, have been granted authority by the state legislature to establish permitted overweight truck c...

  17. Co-simulation of heavy truck tire dynamics and electronic stability control systems (phase A).

    Science.gov (United States)

    2009-07-01

    Electronic stability control (ESC) systems have been proven to be an effective means of preventing instability and loss of control on both passenger vehicles and heavy trucks. In addition, roll stability algorithms are an effective means of reducing ...

  18. 75 FR 52804 - Notice of Funding Availability Application Procedure and Deadlines for the Truck Parking...

    Science.gov (United States)

    2010-08-27

    ... pages in length. Special Note: A description of the project management approach that will guide... truck parking solutions. The FHWA encourages in the project management approach a minimum of a...

  19. Reducing diesel NOx and PM emissions of diesel buses and trucks.

    Science.gov (United States)

    2008-07-01

    The objective of the present investigation was development of a high efficiency : selective catalytic reduction (SCR) system for reducing diesel nitrogen oxides (NOx) and : particulate matters of diesel trucks. The investigation was divided into two ...

  20. Truck Rates For Selected North, South, And Northeastern Brazilian Soybean Export Transportation Routes

    Data.gov (United States)

    Department of Agriculture — Compares monthly truck rates from north Mato Grosso and East Tocantins to the ports Itaituba, Porto Velho, Santarém, São Luís, Santos, and Paranaguá. This is figure...

  1. Biodiesel and Cold Temperature Effects on Speciated Mobile Source Air Toxics from Modern Diesel Trucks

    Science.gov (United States)

    Speciated volatile organic compounds (VOCs) with a particular focus on mobile source air toxics (MSATs) were measured in diesel exhaust from three heavy-duty trucks equipped with modern aftertreatment technologies. Emissions testing was conducted on a temperature controlled chass...

  2. Biodiesel and Cold Temperature Effect on Speciated Mobile Source Air Toxics from Modern Diesel Trucks

    Science.gov (United States)

    Speciated volatile organic compounds (VOCs) with a particular focus on mobile source air toxics (MSATs) were measured in diesel exhaust from three heavy-duty trucks equipped with modern aftertreatment technologies. Emissions testing was conducted on a temperature controlled chass...

  3. 1990 Nationwide Truck Activity and Commodity Survey selected tabulations. Summary report

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    The Nationwide Truck Activity and Commodity Survey (NTACS) provides detailed activity data for a sample of trucks covered in the 1987 Truck Inventory and Use Survey (TIUS) for days selected at random over a 12-month period ending in 1990. The NTACS was conducted by the US Bureau of the Census for the US Department of Transportation (DOT). A Public Use File for the NTACS was developed by Oak Ridge National Laboratory (ORNL) under a reimbursable agreement with the DOT. The content of the Public Use File and the detailed design of the NTACS are described in the ORNL Report {open_quotes}Technical Documentation for the 1990 Nationwide Truck Activity and Commodity Survey Public Use File{close_quotes}. (1992). ORNL Technical Report No. TM-12188, Oak Ridge National Laboratory, Oak Ridge, TN 37831. The main purpose of this summary report is to provide selected tables based on the public use file.

  4. Surrogate Plant Data Base : Volume 4. Appendix E : Medium and Heavy Truck Manufacturing

    Science.gov (United States)

    1983-05-01

    This four volume report consists of a data base describing "surrogate" automobile and truck manufacturing plants developed as part of a methodology for evaluating capital investment requirements in new manufacturing facilities to build new fleets of ...

  5. Integrated vehicle-based safety systems (IVBSS) : heavy truck platform field operational test data analysis plan.

    Science.gov (United States)

    2009-11-23

    This document presents the University of Michigan Transportation Research Institutes plan to perform : analysis of data collected from the heavy truck platform field operational test of the Integrated Vehicle- : Based Safety Systems (IVBSS) progra...

  6. Strategic Design for Delivery with Linked Transportation Assets : Trucks and Drones

    Science.gov (United States)

    2018-01-01

    Home delivery by drones as an alternative or complement to traditional delivery by trucks is attracting considerable attention from major retailers and services, as well as startups. While drone delivery may offer considerable economic savings, the f...

  7. Effect of Michigan multi-axle trucks on pavement distress and profile: volume 2.

    Science.gov (United States)

    2009-02-01

    With the adoption of the new mechanistic-empirical pavement design method and the employment of axle load spectra, the question of evaluating the pavement damage resulting from different axle and truck configurations has become more relevant. In part...

  8. Effect of Michigan multi-axle trucks on pavement distress and profile: volume 3.

    Science.gov (United States)

    2009-02-01

    With the adoption of the new mechanistic-empirical pavement design method and the employment of axle load : spectra, the question of evaluating the pavement damage resulting from different axle and truck configurations has : become more relevant. In ...

  9. Effect of Michigan multi-axle trucks on pavement distress and profile : volume 1.

    Science.gov (United States)

    2009-02-01

    With the adoption of the new mechanistic-empirical pavement design method and the employment of axle load : spectra, the question of evaluating the pavement damage resulting from different axle and truck configurations has : become more relevant. In ...

  10. Impact of Truck Loading on Design and Analysis of Asphaltic Pavement Structures : Phase II

    Science.gov (United States)

    2011-02-01

    In this study, Schaperys nonlinear viscoelastic constitutive model is implemented into the commercial finite element (FE) software ABAQUS via user defined subroutine (user material, or UMAT) to analyze asphalt pavement subjected to heavy truck loa...

  11. Documenting and determining distributions, trends, and relations in truck times at international border crossing facilities.

    Science.gov (United States)

    2017-01-20

    Documenting the times trucks incur when crossing an international border facility is valuable both to the private freight industry and to gateway facility operators and planners. : Members of the project team previously developed and implemented an a...

  12. The determinants of fuel use in the trucking industry – volume, size and the rebound effect

    DEFF Research Database (Denmark)

    Mulalic, Ismir

    2011-01-01

    We analyse the determinants of trucking firm fuel use. We develop a simple model to show that trucking firm fuel use depends, in addition to the fuel price and the traffic volume, also on the output of the trucking firm’s production process (the movement of cargo) measured in tonkilometres......, characteristics of the truck stock, and congestion. We also analyse the rebound effect for road freight transportation, i.e. the percentage of increased energy efficiency that does not result in the reduction of fuel used. For the purpose of analysing the rebound effect for road freight transportation, we...... decompose the standard definition of the rebound effect for motor vehicles, i.e. the elasticity of traffic volume with respect to fuel cost, into the elasticity by which changes in fuel costs affects freight activity and the elasticity by which changes in freight activity affect traffic volume. We estimate...

  13. U02 : heavy truck rollover characterization (phase-A) final report.

    Science.gov (United States)

    2009-01-01

    This Heavy Truck Rollover Characterization Program is a major research effort conducted by the National Transportation Research Center, Inc. (NTRCI) in partnership with Oak Ridge National Laboratory (ORNL), Michelin Americas Research Company (MARC), ...

  14. Real Driving NOx Emissions of European Trucks and Detection of Manipulated Emission Systems

    Science.gov (United States)

    Pöhler, Denis; Adler, Tim; Krufczik, Chsristopher; Horbanski, Martin; Lampel, Johannes; Platt, Ulrich

    2017-04-01

    Nitrogen dioxide (NO2) is the most problematic pollutant in Europe and many other countries. NO2 has a negative impact for the health and the environment, and in most European cities the currently allowed mean annual limit of 40μg/m3 is exceeded. Vehicles, especially Diesel, are the most relevant source. They emit NOx (NO + NO2), and NO can also be converted to NO2 in the atmosphere. Thus vehicle NOx emissions are regulated in the EU with the EURO Norm Standard (e.g. EURO 6 since 1.1.2013 for trucks with 400mg/kWh). Trucks achieve these low emissions with complex emission after treatment systems. All EURO 6 trucks and almost all EURO 5 trucks use the SCR system consuming AdBlue to reduce the NOx emissions. Since the diesel emission scandal for cars, it is well known that real driving emissions (RDE) can be several times higher that the EURO Norm Standard. The main problem is that RDE are only randomly investigated. Here we present a study of NOx RDE of more than 250 randomly chosen trucks on German highways. The measurements were performed with a newly developed mobile NOx-ICAD + CO2 -instrument applying the plume chasing measurement principle, where the pollutants are investigated in the emission plume and were converted to emission factors to be compared to the EURO standard. For most trucks the brand, the model name, the country of registration and its EURO class could be determined and used in a statistical analysis. The observed NOx emission data show that typical truck RDE are in the range of the expected EURO Norm or slightly higher. However, almost every fourth truck from Eastern Europe show emissions much higher that the EURO Norm. This was not observed for German trucks. As the emissions increase up to a factor of 5 to 10 these view trucks contribute significantly to the air pollution. These high emissions clearly indicate a defect emission treatment system. Most likely it indicates illegal manipulated emissions systems where the AdBlue injection is

  15. Baseline scenario(s) for muon collider proton driver

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, Andreas; /Fermilab

    2008-07-01

    This paper gives an overview of the various muon collider scenarios and the requirements they put on the Proton Driver. The required proton power is about 4-6MW in all the scenarios, but the bunch repetition rate varies between 12 and 65Hz. Since none of the muon collider scenarios have been simulated end-to-end, it would be advisable to plan for an upgrade path to around 10MW. Although the proton driver energy is flexible, cost arguments seems to favor a relatively low energy. In particular, at Fermilab 8GeV seems most attractive, partly due to the possibility of reusing the three existing fixed energy storage rings for bunch manipulations.

  16. Scenario development methods and practice

    International Nuclear Information System (INIS)

    2001-01-01

    The safe management of radioactive waste is an essential aspect of all nuclear power programmes. Although a general consensus has been reached in OECD countries on the use of geological repositories for the disposal of high-level radioactive waste, analysis of the long-term safety of these repositories, using performance assessment and other tools, is required prior to implementation. The initial stage in developing a repository safety assessment is the identification of all factors that may be relevant to the long-term safety of the repository and their combination to form scenarios. This must be done in a systematic and transparent way in order to assure the regulatory authorities that nothing important has been forgotten. Scenario development has become the general term used to describe the collection and organisation of the scientific and technical information necessary to assess the long-term performance or safety of radioactive waste disposal systems. This includes the identification of the relevant features, events and processes (FEPs), the synthesis of broad models of scientific understanding, and the selection of cases to be calculated. Scenario development provides the overall framework in which the cases and their calculated consequences can be discussed, including biases or shortcomings due to omissions or lack of knowledge. The NEA Workshop on Scenario Development was organised in Madrid, in May 1999, with the objective of reviewing developments in scenario methodologies and applications in safety assessments since 1992. The outcome of this workshop is the subject of this book. It is a review of developments in scenario methodologies based on a large body of practical experience in safety assessments. It will be of interest to radioactive waste management experts as well as to other specialists involved in the development of scenario methodologies. (author)

  17. Evaluation of US rear underride guard regulation for large trucks using real-world crashes.

    Science.gov (United States)

    Brumbelow, Matthew L; Blanar, Laura

    2010-11-01

    Current requirements for rear underride guards on large trucks are set by the National Highway Traffic Safety Administration in Federal Motor Vehicle Safety Standards (FMVSS) 223 and 224. The standards have been in place since 1998, but their adequacy has not been evaluated apart from two series of controlled crash tests. The current study used detailed reviews of real-world crashes from the Large Truck Crash Causation Study to assess the ability of guards that comply with certain aspects of the regulation to mitigate passenger vehicle underride. It also evaluated the dangers posed by underride of large trucks that are exempt from guard requirements. For the 115 cases meeting the inclusion criteria, coded data, case narratives, photographs, and measurements were used to examine the interaction between study vehicles. The presence and type of underride guard was determined, and its performance in mitigating underride was categorized. Overall, almost one-half of the passenger vehicles had underride damage classified as severe or catastrophic. These vehicles accounted for 23 of the 28 in which occupants were killed. For the cases involving trailers with underride guards compliant with one or both FMVSS, guard deformation or complete failure was frequent and most commonly due to weak attachments, buckling of the trailer chassis, or bending of the lateral end of the guard under narrow overlap loading. Most of the truck units studied qualified for at least one of the FMVSS exemptions. The two largest groups were trailers with small wheel setbacks and single-unit straight trucks. Dump trucks represented a particularly hazardous category of straight truck. The current study suggests several weaknesses in the rear underride guard regulation. The standard allows too much ground clearance, the quasi-static test conditions allow guard designs that fail in narrow overlap crashes, and certifying guards independent of trailers leads to systems with inadequate attachment and

  18. Evaluation of fuel cell auxiliary power units for heavy-duty diesel trucks

    Energy Technology Data Exchange (ETDEWEB)

    Brodrick, Christie-Joy; Farshchi, Mohammad; Lutsey, Nicholas P.; Dwyer, Harry A.; Sperling, Daniel [California Univ., Inst. of Transportation Studies, Davis, CA (United States); Gouse, S. William III [Freightliner LLC, Portland, OR (United States); Harris, D. Bruce; King, Foy G. Jr. [US Environmental Protection Agency, National Risk Management Research Lab., Research Triangle Park, NC (United States); Lipman, Timothy E. [California Univ., Renewable and Appropriate Energy Lab. (RAEL), Berkeley, CA (United States)

    2002-07-01

    A large number of heavy-duty trucks idle a significant amount. Heavy-duty line-haul truck engines idle about 20-40% of the time the engine is running, depending on season and operation. Drivers idle engines to power climate control devices (e.g., heaters and air conditioners) and sleeper compartment accessories (e.g., refrigerators, microwave ovens, and televisions) and to avoid start-up problems in cold weather. Idling increases air pollution and energy use, as well as wear and tear on engines. Efforts to reduce truck idling in the US have been sporadic, in part because it is widely viewed in the trucking industry that further idling restrictions would unduly compromise driver comfort and truck operations. The auxiliary power units (APUs) available to replace the idling of the diesel traction engine all have had limited trucking industry acceptance. Fuel cells are a promising APU technology. Fuel cell APUs have the potential to greatly reduce emissions and energy use and save money. In this paper, we estimate costs and benefits of fuel cell APUs. We calculate the payback period for fuel cell APUs to be about 2.6-4.5 years. This estimate is uncertain since future fuel cell costs are unknown and cost savings from idling vary greatly across the truck fleet. The payback period is particularly sensitive to diesel fuel consumption at idle. Given the large potential environmental and economic benefits of fuel cell APUs, the first major commercial application of fuel cells may be as truck APUs. (Author)

  19. Analysis of vehicle headway distribution on multi-lane freeway considering car–truck interaction

    OpenAIRE

    Dewen Kong; Xiucheng Guo

    2016-01-01

    The primary objective of this study is to identify the characteristics of vehicle headway on multi-lane freeway under lane management in China considering car–truck interaction. More specifically, the study focused on answering the following two questions: (1) whether the car–truck interaction has impact on headway, that is, headway varies by different leading and following vehicle types and (2) what is the best-fitted distribution model for particular headway type under lane management. The ...

  20. Future scenarios of energy for Colombia

    International Nuclear Information System (INIS)

    Smith, Ricardo A; Vesga, Daniel; Cadena, Angela I

    2000-01-01

    The author includes topics as, requirements for the scenarios; process of scenarios, certainty and uncertainty to the horizon of the 2020, definition of axis for the histories and energy scenario for Colombia

  1. New reactors concepts and scenarios

    International Nuclear Information System (INIS)

    Gandini, A.

    2001-01-01

    In recent years an increasing interest is observed with respect to subcritical, accelerator driven systems (ADS), for their possible role in perspective future nuclear energy scenarios, as actinide (Pu and MA) incinerators, and/or claimed energy plants with potential enhanced safety characteristics. Important research programs are devoted to the various related fields of research. Extensive studies on the ADS behavior under incidental conditions are in particular made, for verifying their claimed advantage, under the safety point of view, with respect to the corresponding critical reactors. Corresponding medium and long range scenarios are being studied to cope with a number of concerns associated with the safety (power excursions. residual heat risk), as well as with the fuel flow (criticality accidents, fuel diversion, radiological risk, proliferation). In the present work we shall try to review current lines of research in this field, and comment on possible scenarios so far envisaged. (author)

  2. Scenarios of future energy intensities

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    In this chapter, the authors present scenarios of potential change in energy intensities in the OECD countries and in the Soviet Union. These scenarios are meant to illustrate how intensities might evolve over the next 20 years given different conditions with respect to energy prices, energy-efficiency policies, and other key factors. Changes in intensity will also be affected by the rates of growth and stock turnover in each sector. They have not tried to forecast how activity levels and structure will evolve. However, the OECD scenarios assume a world in which GDP averages growth in the 2-3%/year range, with some differences among countries. For the Soviet Union, the degree and pace of intensity decline will be highly dependent on the success of the transition to a market economy; each scenario explicitly envisions a different degree of success. They have not constructed comparable scenarios for the developing countries. The scenarios presented in this chapter do not predict what will happen in the future. They believe, however, that they illustrate a plausible set of outcomes if energy prices, policies, programs, and other factors evolve as described in each case. With higher energy prices and vigorous policies and programs, intensities in the OECD countries in 2010 could be nearly 50% less on average than the level where trends seem to be point. In the former Soviet Union, a combination of rapid, successful economic reform and extra effort to improve energy efficiency might result in average intensity being nearly 40% less than in a slow reform case. And in the LDCs, a mixture of sound policies, programs, and energy pricing reform could also lead to intensities being far lower than they would be otherwise. 8 refs., 10 figs., 1 tab

  3. Workplace violence in long haul trucking: occupational health nursing update.

    Science.gov (United States)

    Anderson, Debra Gay

    2004-01-01

    Almost 2 million workdays and millions of dollars are lost annually because of non-fatal assaults suffered at the workplace (NIOSH, 1996). Twenty workers, on average, are murdered each week in the United States and an estimated 18,000 workers per week are victims of non-fatal assault (NIOSH, 2001). Violence and stress are two interrelated issues that affect the work force. In-depth studies of these issues have not been conducted with long haul truckers in general, or with women in non-traditional, male dominated fields such as the long haul trucking industry. Epidemiological data related to violence and stress experienced by these under-studied populations are needed to plan effective interventions to reduce occupational risks. Studies employing both qualitative and quantitative methods are needed to articulate risk and protective factors related to violence against workers (Runyan, 2001). Occupational health nurses are qualified to participate in the development and implementation of research and intervention studies to improve worker safety related to violence at the workplace for men and women in both traditional and non-traditional occupational roles.

  4. The analysis of loading losses from tank trucks

    Directory of Open Access Journals (Sweden)

    Jovanović Ana P.

    2006-01-01

    Full Text Available The quantity of loading losses, which are the primary source of evaporative emissions from tank cars and trucks was analyzed in this paper. Loading losses occur as organic vapors in "empty" cargo tanks are displaced to the atmosphere by the liquid being loaded into the tanks. Emissions from loading petroleum liquid were estimated using three methods: the API (American Petroleum Institute method, the VDI (Verein Deutscher Ingenieure -Association of German Engineers method and the Yugoslav Standard JUS B.HO.531 method. The mass of evaporative losses from loading operations is a function of the following parameters: the method of loading the cargo, the physical and chemical characteristics of the cargo and the ambient temperature during loading. Evaporation losses from the loading of motor gasoline (MB-95, BMB-95, MB-98 and MB-86 and diesel fuels (D-2, Euro D-2 were calculated. Losses on a monthly and annual basis were presented for an assumed amount of loaded cargo. It was estimated that the highest loading losses occur in the summer period because of high ambient daily temperatures and in the period of higher transporting levels. It should be pointed out that the loading losses of diesel fuel calculated using an empirical coefficient according to JUS B.HO.531 are significantly higher in comparison with the loading losses calculated using emission factors from the EPA and the VDI method. The gasoline loading losses calculated using emission factors derived from the three methods are similar.

  5. Fuzzy logic anti-skid control for commercial trucks

    Science.gov (United States)

    Akey, Mark L.

    1995-06-01

    A fuzzy logic (FL) anti-skid brake controller (ABS) is proposed as the next generation ABS replacing current generation finite state (FS) control. The FL controller is part of a commercial truck braking system, encompassing reverse front-back braking proportions on an articulated vehicle as compared to that found on fixed, passenger car systems. In this early research, the FL controller must satisfy three goals. The first goal is to produce superior braking distances over that of the finite state controller, specifically under low (mu) conditions. The second goal is to provide superior braking under varying system conditions (road surface conditions, physical brake parameters, wheel velocity sensor parameters). The third goal is to provide a convenient, flexible, and tractable ABS solution which is amenable to redevelopemnt to different vehicular platforms. Monte Carlo simulation results illustrate stopping distance improvements of 5 to 10 % averaged over all (mu) surfaces for varying wheel loads. On low (mu) surfaces, the improvement increases to 15% (up to a full tractor-trailer length). These results are obtained while varying other system parameters demonstrating robustness. Finally, the fuzzy logic rule sets and the overall configuration illustrate a straight-forward design and maturation process for the rule sets.

  6. The dynamics of the three-piece-freight truck

    DEFF Research Database (Denmark)

    Xia, Fujie

    2002-01-01

    body and the side supports on the bolsters the side supports must be modelled as nonlinear dead-band springs. The clearances in the assembly in the wedge damper systems give rise to a relative yaw motion of the bolster with respect to the side frame and a rotation around the truck center line and cause...... a warping. In addition the assembly clearances between the side frame and the adapter both in longitudinal and lateral directions produce another dead-band spring force. The tractive effort on the car body in the longitudinal direction may be left out of consideration in the modelling of the passenger car...... at all. The motion of the bolsters are at least two dimensional in the lateral and the vertical directions, so the friction on the surfaces of a wedge should be treated as two-dimensional dry friction, and the same is true for the dry friction on the surfaces of an adapter. For the motion with dry...

  7. [Femicides: concepts, types and scenarios].

    Science.gov (United States)

    Meneghel, Stela Nazareth; Portella, Ana Paula

    2017-09-01

    This text is a theoretical essay that discusses the concepts, types and scenarios of feminicides, and presents some proposals for the prevention of these premature, unjust and avoidable deaths. The text revisits the original concept of femicide proposed by Diana Russell and Jane Caputti and shows new and old scenarios where these crimes occur. It points to patriarchy, understood as being a hierarchical system of power between men and women, as one of the main determinants of these deaths. It ends by presenting actions and proposals to prevent and combat these gender crimes.

  8. Dose estimates in a loss of lead shielding truck accident.

    Energy Technology Data Exchange (ETDEWEB)

    Dennis, Matthew L.; Osborn, Douglas M.; Weiner, Ruth F.; Heames, Terence John (Alion Science & Technology Albuquerque, NM)

    2009-08-01

    The radiological transportation risk & consequence program, RADTRAN, has recently added an updated loss of lead shielding (LOS) model to it most recent version, RADTRAN 6.0. The LOS model was used to determine dose estimates to first-responders during a spent nuclear fuel transportation accident. Results varied according to the following: type of accident scenario, percent of lead slump, distance to shipment, and time spent in the area. This document presents a method of creating dose estimates for first-responders using RADTRAN with potential accident scenarios. This may be of particular interest in the event of high speed accidents or fires involving cask punctures.

  9. Particle production in Ekpyrotic scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Hipólito-Ricaldi, W.S. [Physics Department, McGill University,Montreal, QC, H3A 2T8 (Canada); Departamento de Ciências Naturais, Universidade Federal do Espirito Santo,Rodovia BR 101 Norte, km. 60, Campus de São Mateus, CEP 29932-540,São Mateus, Espirito Santo (Brazil); Brandenberger, Robert [Physics Department, McGill University,Montreal, QC, H3A 2T8 (Canada); Institute for Theoretical Studies, ETH Zürich,CH-8092 Zürich (Switzerland); Ferreira, Elisa G.M.; Graef, L.L. [Physics Department, McGill University,Montreal, QC, H3A 2T8 (Canada)

    2016-11-09

    We consider Parker particle production in the Ekpyrotic scenario (in particular in the New Ekpyrotic model) and show that the density of particles produced by the end of the phase of Ekpyrotic contraction can be sufficient to lead to a hot state of matter after the bounce. Hence, no separate reheating mechanism is necessary.

  10. Emissions scenario: a final response

    Energy Technology Data Exchange (ETDEWEB)

    Gruebler, A.; Nakicenovic, N.; Alcamo, J. (and others)

    2004-01-01

    This note is a final response to the debate raised by Mr Castles and Mr Henderson (for brevity, we refer here to the two authors simply as C and H) in this Journal (vol. 14, no. 2 and 3, and no. 4) on the issue of economic growth in developing countries in some of the emissions scenarios published in the IPCC Special Report on Emissions Scenarios (SRES) (Nakicenovic et al., 2000). We first outline areas of agreement and then the remaining areas of disagreement. Two important areas of agreement have emerged from the debate according to our view. First, both parties agree that scenarios assuming a conditional convergence in income levels, i.e., a higher growth in per capita income in poorer countries when compared to countries with higher levels of affluence, are both ''plausible and well attested in economic history'' (C and H, p. 424). Thus, the fundamental, structural characteristic of some of the SRES scenarios contested by C and H are not challenged per se, but rather how fast such trends could unfold in the future. (author)

  11. Emissions scenarios: a final response

    Energy Technology Data Exchange (ETDEWEB)

    Gruebler, A.; Nakicenovic, N.; Alcamo, J. (and others)

    2004-01-01

    This note is a final response to the debate raised by Mr. Castles and Mr. Henderson (for brevity, we refer here to the two authors simply as C and H) in this Journal (vol 14, no 2 and 3, and no 4) on the issue of economic growth in developing countries in some of the emissions scenarios published in the IPCC Special Report on Emissions Scenarios (SRES) (Nakicenovic et al., 2000). We first outline areas of agreement and then the remaining areas of disagreement. Two important areas of agreement have emerged from the debate according to our view. First, both parties agree that scenarios assuming a conditional convergence in income levels, i.e., a higher growth in per capita income in poorer countries when compared to countries with higher levels of affluence, are both 'plausible and well attested in economic history' (C and H, p. 424). Thus, the fundamental, structural characteristic of some of the SRES scenarios contested by C and H are not challenged per se, but rather how fast such trends could unfold in the future. (author)

  12. At home and away: measuring the sleep of Australian truck drivers.

    Science.gov (United States)

    Baulk, Stuart D; Fletcher, Adam

    2012-03-01

    The causes of fatigue in truck drivers related to work hours have been studied extensively and are reasonably well understood. However, much less is known about how rest opportunities can be structured to optimise recovery from fatigue. The nature of the road transport industry often requires that rest be taken in various locations. New investigation in this area, focusing on sleep obtained in truck cabs and other non-home environments is critically important to complement existing understanding. This study examined sleep at home and in truck cabs, in truck drivers who were actively working during the time of the study. Thirty-seven male drivers aged between 24 and 63 years (age: 48.7 ± 9.0 years; mean ± SD) wore activity monitors (also known as 'sleep watches') and completed work and sleep diaries for a period of 21 days, recording their subjective fatigue levels before, during and after work shifts, and before and after sleep periods. They also self-rated their sleep quality and noted the number of times they woke during sleep periods. Analyses focused on home versus in-truck sleep periods. The subjective data suggested that a greater quantity (P<.001) and quality (P<.05) of sleep was obtained at home than in the truck, and that sleeping at home more effectively reduced fatigue levels (P<.001). The objective data showed trends towards longer sleep length at home, but other variables, including total sleep per 24h and sleep quality, showed no significant differences. This study demonstrates that measuring sleep quantity and quality in operational road transport environments is feasible. The findings caution against over-reliance on laboratory and simulator studies since there are critical aspects of the operating environment that cannot be validly studied in artificially controlled settings. This study is unique in its direct examination of sleep quantity and quality in truck drivers sleeping at home and away from home. Copyright © 2011 Elsevier Ltd. All rights

  13. Truck drivers’ perceptions on wearable devices and health promotion: a qualitative study

    Directory of Open Access Journals (Sweden)

    Rama Greenfield

    2016-07-01

    Full Text Available Abstract Background Professional truck drivers, as other shift workers, have been identified as a high-risk group for various health conditions including cardiovascular disease, obesity, diabetes, sleep apnoea and stress. Mobile health technologies can potentially improve the health and wellbeing of people with a sedentary lifestyle such as truck drivers. Yet, only a few studies on health promotion interventions related to mobile health technologies for truck drivers have been conducted. We aimed to explore professional truck drivers’ views on health promotion delivered via mobile health technologies such as wearable devices. Methods We conducted a phenomenological qualitative study, consisting of four semi-structured focus groups with 34 full-time professional truck drivers in the UK. The focus groups were audio-taped, transcribed verbatim and analysed using thematic content analysis. We discussed drivers’ perceptions of their health, lifestyle and work environment, and their past experience and expectations from mobile health technologies. Results The participants viewed their lifestyle as unhealthy and were aware of possible consequences. They expressed the need and wish to change their lifestyle, yet perceived it as an inherent, unavoidable outcome of their occupation. Current health improvement initiatives were not always aligned with their working conditions. The participants were generally willing to use mobile health technologies such as wearable devices, as a preventive measure to avoid prospect morbidity, particularly cardiovascular diseases. They were ambivalent about privacy and the risk of their employer’s monitoring their clinical data. Conclusions Wearable devices may offer new possibilities for improving the health and wellbeing of truck drivers. Drivers were aware of their unhealthy lifestyle. They were interested in changing their lifestyle and health. Drivers raised concerns regarding being continuously monitored by

  14. Demonstration Project 111, ITS/CVO Technology Truck, Final Project Report

    Energy Technology Data Exchange (ETDEWEB)

    Gambrell, KP

    2002-01-11

    In 1995, the planning and building processes began to design and develop a mobile demonstration unit that could travel across the nation and be used as an effective outreach tool. In 1997, the unit was completed; and from June 1997 until December 2000, the Federal Highway Administration (FHWA)/Federal Motor Carrier Safety Administration (FMCSA) mobilized the Technology Truck, also known as Demonstration Project No. 111, ''Advanced Motor Carrier Operations and Safety Technologies.'' The project featured the latest available state-of-the-practice intelligent transportation systems (ITS) technologies designed to improve both the efficiency and safety of commercial vehicle operations (CVO). The Technology Truck was designed to inform and educate the motor carrier community and other stakeholders regarding ITS technologies, thus gaining support and buy-in for participation in the ITS program. The primary objective of the project was to demonstrate new and emerging ITS/CVO technologies and programs, showing their impact on motor carrier safety and productivity. In order to meet the objectives of the Technology Truck project, the FHWA/FMCSA formed public/private partnerships with industry and with Oak Ridge National Laboratory to demonstrate and display available ITS/CVO technologies in a cooperative effort. The mobile demonstration unit was showcased at national and regional conferences, symposiums, universities, truck shows and other venues, in an effort to reach as many potential users and decision makers as possible. By the end of the touring phase, the ITS/CVO Technology Truck had been demonstrated in 38 states, 4 Canadian provinces, 88 cities, and 114 events; been toured by 18,099 people; and traveled 115,233 miles. The market penetration for the Technology Truck exceeded 4,000,000, and the website received more than 25,000 hits. In addition to the Truck's visits, the portable ITS/CVO kiosk was demonstrated at 31 events in 23 cites in 15

  15. Modeling mechanical restriction differences between car and heavy truck in two-lane cellular automata traffic flow model

    Science.gov (United States)

    Li, Xin; Li, Xingang; Xiao, Yao; Jia, Bin

    2016-06-01

    Real traffic is heterogeneous with car and truck. Due to mechanical restrictions, the car and the truck have different limited deceleration capabilities, which are important factors in safety driving. This paper extends the single lane safety driving (SD) model with limited deceleration capability to two-lane SD model, in which car-truck heterogeneous traffic is considered. A car has a larger limited deceleration capability while a heavy truck has a smaller limited deceleration capability as a result of loaded goods. Then the safety driving conditions are different as the types of the following and the leading vehicles vary. In order to eliminate the well-known plug in heterogeneous two-lane traffic, it is assumed that heavy truck has active deceleration behavior when the heavy truck perceives the forming plug. The lane-changing decisions are also determined by the safety driving conditions. The fundamental diagram, spatiotemporal diagram, and lane-changing frequency were investigated to show the effect of mechanical restriction on heterogeneous traffic flow. It was shown that there would be still three traffic phases in heterogeneous traffic condition; the active deceleration of the heavy truck could well eliminate the plug; the lane-changing frequency was low in synchronized flow; the flow and velocity would decrease as the proportion of heavy truck grows or the limited deceleration capability of heavy truck drops; and the flow could be improved with lane control measures.

  16. Exploring NASA Human Spaceflight and Pioneering Scenarios

    Science.gov (United States)

    Zapata, Edgar; Wilhite, Alan

    2015-01-01

    The life cycle cost analysis of space exploration scenarios is explored via a merger of (1) scenario planning, separating context and (2) modeling and analysis of specific content. Numerous scenarios are presented, leading to cross-cutting recommendations addressing life cycle costs, productivity, and approaches applicable to any scenarios. Approaches address technical and non-technical factors.

  17. Toxoplasma gondii infection in interstate truck drivers: a case-control seroprevalence study.

    Science.gov (United States)

    Alvarado-Esquivel, Cosme; Pacheco-Vega, Sandy Janet; Hernández-Tinoco, Jesús; Salcedo-Jáquez, Misael; Sánchez-Anguiano, Luis Francisco; Berumen-Segovia, Luis Omar; Rábago-Sánchez, Elizabeth; Liesenfeld, Oliver

    2015-02-05

    Infection with Toxoplasma gondii can be acquired via the ingestion of undercooked or raw meat containing tissue cysts, or via ingestion of water contaminated with oocysts. Professional long distance truck driving may have epidemiological importance for food-borne infections since drivers eat out of home and in places where hygiene and cooking practices are uncertain. We aimed to determine whether interstate truck drivers in Durango, Mexico have an increased risk of infection with T. gondii as indicated by seropositivity; and to determine the socio-demographic, work, clinical, and behavioral characteristics associated with T. gondii seropositivity in interstate truck drivers. Through a case-control study design, 192 truck drivers and 192 controls from the general population of the same region matched by gender and age were examined with enzyme-linked immunoassays for the presence of anti-Toxoplasma IgG and IgM antibodies. Socio-demographic, work, clinical and behavioral characteristics from the truck drivers were obtained. Anti-T. gondii IgG antibodies were found in 23 (12.0%) of 192 truck drivers and in 13 (6.8%) of 192 controls (OR = 21.0; 95% CI: 1.23-358.38; P = 0.002). Anti-T. gondii IgM antibodies were found in 7 (3.6%) cases and in 7 (3.6%) controls (P = 1.00). The seroprevalence of T. gondii infection was higher in drivers with reflex impairment than in those without this impairment (4/13, 30.8% vs 19/179, 10.6%, respectively; P = 0.05), and in drivers with hearing impairment than in those without this impairment (3/7, 42.9% vs 20/185, 10.8%, respectively; P = 0.03). Multivariate analysis of work and behavioral characteristics of truck drives showed positive associations of T. gondii exposure with trips to the south of Mexico (OR = 3.11; 95% CI: 1.02-9.44; P = 0.04) and consumption of horse meat (OR = 5.18; 95% CI: 1.62-16.55; P = 0.005). Results suggest that interstate truck drivers may have an increased risk for T

  18. Effects of After-Treatment Control Technologies on Heavy-Duty Diesel Truck Emissions

    Science.gov (United States)

    Preble, C.; Dallmann, T. R.; Kreisberg, N. M.; Hering, S. V.; Harley, R.; Kirchstetter, T.

    2015-12-01

    Diesel engines are major emitters of nitrogen oxides (NOx) and the black carbon (BC) fraction of particulate matter (PM). Diesel particle filter (DPF) and selective catalytic reduction (SCR) emission control systems that target exhaust PM and NOx have recently become standard on new heavy-duty diesel trucks (HDDT). There is concern that DPFs may increase ultrafine particle (UFP) and total particle number (PN) emissions while reducing PM mass emissions. Also, the deliberate catalytic oxidation of engine-out NO to NO2 in continuously regenerating DPFs may lead to increased tailpipe emission of NO2 and near-roadway concentrations that exceed the 1-hr national ambient air quality standard. Increased NO2 emissions can also promote formation of ozone and secondary PM. We report results from ongoing on-road studies of HDDT emissions at the Port of Oakland and the Caldecott Tunnel in California's San Francisco Bay Area. Emission factors (g pollutant per kg diesel) were linked via recorded license plates to each truck's engine model year and installed emission controls. At both sites, DPF use significantly increased the NO2/NOx emission ratio. DPFs also significantly increased NO2 emissions when installed as retrofits on older trucks with higher baseline NOx emissions. While SCR systems on new trucks effectively reduce total NOx emissions and mitigate these undesirable DPF-related NO2 emissions, they also lead to significant emission of N2O, a potent greenhouse gas. When expressed on a CO2-equivalent basis, the N2O emissions increase offsets the fuel economy gain (i.e., the CO2 emission reduction) associated with SCR use. At the Port, average NOx, BC and PN emission factors from new trucks equipped with DPF and SCR were 69 ± 15%, 92 ± 32% and 66 ± 35% lower, respectively, than modern trucks without these emission controls. In contrast, at the Tunnel, PN emissions from older trucks retrofit with DPFs were ~2 times greater than modern trucks without DPFs. The difference

  19. Prediction of fuel consumption of mining dump trucks: A neural networks approach

    International Nuclear Information System (INIS)

    Siami-Irdemoosa, Elnaz; Dindarloo, Saeid R.

    2015-01-01

    Highlights: • A neural network model of fuel consumption in mining haul trucks was constructed and tested. • Using the cyclic activities, the model was able to predict unseen (testing) data. • Trucks idle times were identified as the most important unnecessary energy consuming portion of the network. • Practical remedies, based on the nature of mining operations, were proposed to reduce the energy consumption. - Abstract: Fuel consumption of mining dump trucks accounts for about 30% of total energy use in surface mines. Moreover, a fleet of large dump trucks is the main source of greenhouse gas (GHG) generation. Modeling and prediction of fuel consumption per cycle is a valuable tool in assessing both energy costs and the resulting GHG generation. However, only a few studies have been published on fuel prediction in mining operations. In this paper, fuel consumption per cycle of operation was predicted using artificial neural networks (ANN) technique. Explanatory variables were: pay load, loading time, idled while loaded, loaded travel time, empty travel time, and idled while empty. The output variable was the amount of fuel consumed in one cycle. Mean absolute percentage error (MAPE) of 10% demonstrated applicability of ANN in prediction of the fuel consumption. The results demonstrated the considerable effect of mining trucks idle times in fuel consumption. A large portion of the unnecessary energy consumption and GHG generation, in this study, was solely due to avoidable idle times. This necessitates implementation of proper actions/remedies in form of both preventive and corrective actions

  20. Vibration Study of Fork-lift Truck Based on the Virtual Prototype Technology

    Directory of Open Access Journals (Sweden)

    YANG Mingliang

    2014-05-01

    Full Text Available The forklift truck is one of important equipments of the modern logistics system. As the forklift truck is running, the driver seat and steering wheel of a certain type of fork-lift truck vibrate strongly, virtual prototyping technology and multi-body dynamics are used to make simulation of dynamic performance of fork-lift truck in this paper, and then the test result is compared with time course load that obtained from frame junction with the annex. We should repeatedly modify the simulation model based on test results, which is consistent with the actual results. Based on this model, so we put forward measures for improving design: Firstly, the axis of rotation of oval steering axle is implied; Secondly, the overhead guard is connected with the frame by the rubber cushion blocks at four different locations; Thirdly, the engine is fixed on the frame by the rubber cushion blocks (shock mount in two different position. The improved simulation and experimental verification are carried out under the same conditions, and the results show that the fundamental frequency of seat of the improved fork-lift truck and vibration energy are lower. The result proves the practical value of this method in the research of the vibration characteristics of complete engineering machine.

  1. Radio Frequency Identification (RFID) and communication technologies for solid waste bin and truck monitoring system.

    Science.gov (United States)

    Hannan, M A; Arebey, Maher; Begum, R A; Basri, Hassan

    2011-12-01

    This paper deals with a system of integration of Radio Frequency Identification (RFID) and communication technologies for solid waste bin and truck monitoring system. RFID, GPS, GPRS and GIS along with camera technologies have been integrated and developed the bin and truck intelligent monitoring system. A new kind of integrated theoretical framework, hardware architecture and interface algorithm has been introduced between the technologies for the successful implementation of the proposed system. In this system, bin and truck database have been developed such a way that the information of bin and truck ID, date and time of waste collection, bin status, amount of waste and bin and truck GPS coordinates etc. are complied and stored for monitoring and management activities. The results showed that the real-time image processing, histogram analysis, waste estimation and other bin information have been displayed in the GUI of the monitoring system. The real-time test and experimental results showed that the performance of the developed system was stable and satisfied the monitoring system with high practicability and validity. Copyright © 2011 Elsevier Ltd. All rights reserved.

  2. Work, sleep, and cholesterol levels of U.S. long-haul truck drivers.

    Science.gov (United States)

    Lemke, Michael K; Apostolopoulos, Yorghos; Hege, Adam; Wideman, Laurie; Sönmez, Sevil

    2017-04-07

    Long-haul truck drivers in the United States experience elevated cardiovascular health risks, possibly due to hypercholesterolemia. The current study has two objectives: 1) to generate a cholesterol profile for U.S. long-haul truck drivers; and 2) to determine the influence of work organization characteristics and sleep quality and duration on cholesterol levels of long-haul truck drivers. Survey and biometric data were collected from 262 long-haul truck drivers. Descriptive analyses were performed for demographic, work organization, sleep, and cholesterol measures. Linear regression and ordinal logistic regression analyses were conducted to examine for possible predictive relationships between demographic, work organization, and sleep variables, and cholesterol outcomes. The majority (66.4%) of drivers had a low HDL (risk total cholesterol to HDL cholesterol ratio. Sleep quality was associated with HDL, LDL, and total cholesterol, and daily work hours were associated with LDL cholesterol. Workday sleep duration was associated with non-HDL cholesterol, and driving experience and sleep quality were associated with cholesterol ratio. Long-haul truck drivers have a high risk cholesterol profile, and sleep quality and work organization factors may induce these cholesterol outcomes. Targeted worksite health promotion programs are needed to curb these atherosclerotic risks.

  3. Metaheuristic Approaches for Solving Truck and Trailer Routing Problems with Stochastic Demands: A Case Study in Dairy Industry

    Directory of Open Access Journals (Sweden)

    Seyedmehdi Mirmohammadsadeghi

    2015-01-01

    Full Text Available Manufacturers and service providers often encounter stochastic demand scenarios. Researchers have, thus far, considered the deterministic truck and trailer routing problem (TTRP that cannot address ubiquitous demand uncertainties and/or other complexities. The purpose of this study is to model the TTRP with stochastic demand (TTRPSD constraints to bring the TTRP model closer to a reality. The model is solved in a reasonable timeframe using data from a large dairy service by administering the multipoint simulated annealing (M-SA, memetic algorithm (MA, and tabu search (TS. A sizeable number of customers whose demands follow the Poisson probability distribution are considered to model and solve the problem. To make the solutions relevant, first, 21 special TTRPSD benchmark instances are modified for this case and then these benchmarks are used in order to increase the validity and efficiency of the aforementioned algorithms and to show the consistency of the results. Also, the solutions have been tested using sensitivity analysis to understand the effects of the parameters and to make a comparison between the best results obtained by three algorithms and sensitivity analysis. Since the differences between the results are insignificant, the algorithms are found to be appropriate and relevant for solving real-world TTRPSD problem.

  4. EON UK CORPORATE SCENARIO PLANNING 2020

    OpenAIRE

    Bedi, Rahul; Singh, Paminder; Lee, Chih-Shan

    2008-01-01

    Abstract This research project sets out to explore how scenarios can help to develop strategy in conditions of uncertainty. It suggests that scenarios can be used as intermediary objects to discuss alternative scenarios and generate new strategic approaches. The paper sets to explore how scenario planning is linked to strategy examining a practical application of scenario planning at EON, worlds largest privately owned energy provider. The purpose of this intervention in EON was...

  5. Global energy context: future scenarios

    International Nuclear Information System (INIS)

    Beretta, Gian Paolo

    2006-01-01

    After a brief analysis of the history of global energy consumption, this paper discusses a plausible scenario of energy needs and related carbon emissions for the rest of the century. The global outlook and the probable evolution of several factors that impact on energy policy considerations - even on the local scale - demonstrate the great complexity and planetary dimension of the problems, as well as the almost certain sterility of out-of-context domestic energy-policy measures [it

  6. Emergent physics: Fermi point scenario

    OpenAIRE

    Volovik, G. E.

    2008-01-01

    The Fermi-point scenario of emergent gravity has the following consequences: gravity emerges together with fermionic and bosonic matter; emergent fermionic matter consists of massless Weyl fermions; emergent bosonic matter consists of gauge fields; Lorentz symmetry persists well above the Planck energy; space-time is naturally 4-dimensional; Universe is naturally flat; cosmological constant is naturally small or zero; underlying physics is based on discrete symmetries; `quantum gravity' canno...

  7. Scenarios and Strategies for Africa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-11-15

    In 2011, IRENA will start developing scenarios and strategies for Africa. This is a pilot study for a project that will ultimately encompass the whole world. The selection of Africa first indicates the priority that the IRENA work programme places on the continent. In the framework of the 2011 IRENA work programme, the analysis of scenarios and strategies will feed into the renewables readiness assessment, which will assess policy priorities and best practices in renewable energy policy-making. This, in turn, will be the basis for financing investment and capacity building activities. Energy policy advice must consider issues, such as the structure of energy supply and demand, the past and future energy trends, renewable energy resources, energy economics and technology access. Scenarios and strategies are key tools for such an analysis. Regional and national differences must be considered and individual sectors and end-use categories further analysed. These include power generation, cooking, heating, industrial process heat, and transport. Urban and rural solutions will be dealt with separately, as well as centralised and decentralised solutions. The analysis will cover issues, such as potentials, technology, supply chains and investment needs.

  8. Simulating geometrically complex blast scenarios

    Directory of Open Access Journals (Sweden)

    Ian G. Cullis

    2016-04-01

    Full Text Available The effects of blast waves generated by energetic and non-energetic sources are of continuing interest to the ballistics research community. Modern conflicts are increasingly characterised by asymmetric urban warfare, with improvised explosive devices (IEDs often playing a dominant role on the one hand and an armed forces requirement for minimal collateral effects from their weapons on the other. These problems are characterised by disparate length- and time-scales and may also be governed by complex physics. There is thus an increasing need to be able to rapidly assess and accurately predict the effects of energetic blast in topologically complex scenarios. To this end, this paper presents a new QinetiQ-developed advanced computational package called EAGLE-Blast, which is capable of accurately resolving the generation, propagation and interaction of blast waves around geometrically complex shapes such as vehicles and buildings. After a brief description of the numerical methodology, various blast scenario simulations are described and the results compared with experimental data to demonstrate the validation of the scheme and its ability to describe these complex scenarios accurately and efficiently. The paper concludes with a brief discussion on the use of the code in supporting the development of algorithms for fast running engineering models.

  9. Test, Evaluation, and Demonstration of Practical Devices/Systems to Reduce Aerodynamic Drag of Tractor/Semitrailer Combination Unit Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Scott Smith; Karla Younessi; Matt Markstaller; Dan Schlesinger; Bhaskar Bhatnagar; Donald Smith; Bruno Banceu; Ron Schoon; V.K. Sharma; Mark Kachmarsky; Srikant Ghantae; Michael Sorrels; Conal Deedy; Justin Clark; Skip Yeakel; Michael D. Laughlin; Charlotte Seigler; Sidney Diamond

    2007-04-30

    Class 8 heavy-duty trucks account for over three-quarters of the total diesel fuel used by commercial trucks (trucks with GVWRs more than 10,000 pounds) in the United States each year. At the highway speeds at which these trucks travel (i.e., 60 mph or greater), aerodynamic drag is a major part of total horsepower needed to move the truck down the highway, Reductions in aerodynamic drag can yield measurable benefits in fuel economy through the use of relatively inexpensive and simple devices. The goal of this project was to examine a number of aerodynamic drag reduction devices and systems and determine their effectiveness in reducing aerodynamic drag of Class 8 tractor/semitrailer combination-units, thus contributing to DOE's goal of reducing transportation petroleum use. The project team included major heavy truck manufacturers in the United States, along with the management and industry expertise of the Truck Manufacturers Association as the lead investigative organization. The Truck Manufacturers Association (TMA) is the national trade association representing the major North American manufacturers of Class 6-8 trucks (GVWRs over 19,500 lbs). Four major truck manufacturers participated in this project with TMA: Freightliner LLC; International Truck and Engine Corporation; Mack Trucks Inc.; and Volvo Trucks North America, Inc. Together, these manufacturers represent over three-quarters of total Class 8 truck sales in the United States. These four manufacturers pursued complementary research efforts as part of this project. The project work was separated into two phases conducted over a two-year period. In Phase I, candidate aerodynamic devices and systems were screened to focus research and development attention on devices that offered the most potential. This was accomplished using full-size vehicle tests, scale model tests, and computational fluid dynamics analyses. In Phase II, the most promising devices were installed on full-size trucks and their

  10. Effect of leaving milk trucks empty and idle for 6 h between raw milk loads.

    Science.gov (United States)

    Kuhn, Eva; Meunier-Goddik, Lisbeth; Waite-Cusic, Joy G

    2018-02-01

    The US Pasteurized Milk Ordinance (PMO) allows milk tanker trucks to be used repeatedly for 24 h before mandatory clean-in-place cleaning, but no specifications are given for the length of time a tanker can be empty between loads. We defined a worst-case hauling scenario as a hauling vessel left empty and dirty (idle) for extended periods between loads, especially in warm weather. Initial studies were conducted using 5-gallon milk cans (pilot-scale) as a proof-of-concept and to demonstrate that extended idle time intervals could contribute to compromised raw milk quality. Based on pilot-scale results, a commercial hauling study was conducted through partnership with a Pacific Northwest dairy co-op to verify that extended idle times of 6 h between loads have minimal influence on the microbiological populations and enzyme activity in subsequent loads of milk. Milk cans were used to haul raw milk (load 1), emptied, incubated at 30°C for 3, 6, 10, and 20 h, and refilled with commercially pasteurized whole milk (load 2) to measure cross-contamination. For the commercial-scale study, a single tanker was filled with milk from a farm known to have poorer quality milk (farm A, load 1), emptied, and refilled immediately (0 h) or after a delay (6 h) with milk from a farm known to have superior quality milk (farm B, load 2). In both experiments, milk samples were obtained from each farm's bulk tank and from the milk can or tanker before unloading. Each sample was microbiologically assessed for standard plate count (SPC), lactic acid bacteria (LAB), and coliform counts. Selected isolates were assessed for lipolytic and proteolytic activity using spirit blue agar and skim milk agar, respectively. The pilot-scale experiment effectively demonstrated that extended periods of idle (>3 h) of soiled hauling vessels can significantly affect the microbiological quality of raw milk in subsequent loads; however, extended idle times of 6 h or less would not measurably compromise milk

  11. FedEx Gasoline Hybrid Electric Delivery Truck Evaluation: 6-Month Interim Report

    Energy Technology Data Exchange (ETDEWEB)

    Barnitt, R.

    2010-05-01

    This interim report presents partial (six months) results for a technology evaluation of gasoline hybrid electric parcel delivery trucks operated by FedEx in and around Los Angeles, CA. A 12 month in-use technology evaluation comparing in-use fuel economy and maintenance costs of GHEVs and comparative diesel parcel delivery trucks was started in April 2009. Comparison data was collected and analyzed for in-use fuel economy and fuel costs, maintenance costs, total operating costs, and vehicle uptime. In addition, this interim report presents results of parcel delivery drive cycle collection and analysis activities as well as emissions and fuel economy results of chassis dynamometer testing of a gHEV and a comparative diesel truck at the National Renewable Energy Laboratory's (NREL) ReFUEL laboratory. A final report will be issued when 12 months of in-use data have been collected and analyzed.

  12. STRESS LOADING SIMULATION OF HYDRO-MECHANICAL TRANSMISSION OF DUMP TRUCK

    Directory of Open Access Journals (Sweden)

    S. A. Sidorov

    2006-01-01

    Full Text Available The Transmission model and software package to investigate stress loading of a hydromechanical transmission of a dump truck have been developed. The given software package allows to model stress loading of transmission gears in taking-off and acceleration modes at various road resistance, positions of an engine control pedal and initial revolutions of an engine crankshaft, various laws of friction clutch switching and some other parameters that permit to reveal a rate of various operational mode influence on stress loading of a dump truck transmission. An equivalence of the developed software is proved by the comparison of the experimentally obtained stress loading process of the hydro-mechanical transmission of a BelAZ- 7555 dump truck with the results of the simulation 

  13. Experimental study on transportation safety of package in side collision of heavy duty truck

    International Nuclear Information System (INIS)

    Suga, M.; Sasaki, T.

    1989-01-01

    The accidents in road transportation of package may be collision, fall and fire. It is necessary to examine all cases very carefully because collision might be caused by other vehicle. Collisions are classified into head-on collision, rear-end collision, side collision. A lot of experiments and analyses are reported on head-on collision, so the behavior of vehicle and package may be predicted without difficulty. Rear-end collisions bring about less impact and may be applied corresponding to the head-on collisions. About side collisions, few experiments or analyses are reported, and most of them are about passenger cars not about trucks. So it becomes important to study the transportation safety of package carried on a heavy duty truck when hit on the side by another truck similar in size

  14. Measurement of stress distributions in truck tyre contact patch in real rolling conditions

    Science.gov (United States)

    Anghelache, Gabriel; Moisescu, Raluca

    2012-12-01

    Stress distributions on three orthogonal directions have been measured across the contact patch of truck tyres using the complex measuring system that contains a transducer assembly with 30 sensing elements placed in the road surface. The measurements have been performed in straight line, in real rolling conditions. Software applications for calibration, data acquisition, and data processing were developed. The influence of changes in inflation pressure and rolling speed on the shapes and sizes of truck tyre contact patch has been shown. The shapes and magnitudes of normal, longitudinal, and lateral stress distributions, measured at low speed, have been presented and commented. The effect of wheel toe-in and camber on the stress distribution results was observed. The paper highlights the impact of the longitudinal tread ribs on the shear stress distributions. The ratios of stress distributions in the truck tyre contact patch have been computed and discussed.

  15. Electro-deposition painting process improvement of cab truck by Six Sigma concept

    Science.gov (United States)

    Kawitu, Kitiya; Chutima, Parames

    2017-06-01

    The case study company is a manufacturer of trucks and currently facing a high rework cost due to the thickness of the electro-deposited paint (EDP) of the truck cab is lower than standard. In addition, the process capability is very low. The Six Sigma concept consisting of 5 phases (DMAIC) is applied to determine new parameter settings for each significant controllable factor. After the improvement, EDP thickness of the truck cab increases from 17.88μ to 20μ (i.e. standard = 20 ± 3μ). Moreover, the process capability indexes (Cp and Cpk) are increased from 0.9 to 1.43, and from 0.27 to 1.43, respectively. This improvement could save the rework cost about 1.6M THB per year.

  16. A comprehensive analysis of factors influencing the injury severity of large-truck crashes.

    Science.gov (United States)

    Zhu, Xiaoyu; Srinivasan, Sivaramakrishnan

    2011-01-01

    Given the importance of trucking to the economic well being of a country and the safety concerns posed by the trucks, a study of large-truck crashes is critical. This paper contributes by undertaking an extensive analysis of the empirical factors affecting injury severity of large-truck crashes. Data from a recent, nationally representative sample of large-truck crashes are examined to determine the factors affecting the overall injury severity of these crashes. The explanatory factors include the characteristics of the crash, vehicle(s), and the driver(s). The injury severity was modeled using two measures. Several similarities and some differences were observed across the two models which underscore the need for improved accuracy in the assessment of injury severity of crashes. The estimated models capture the marginal effects of a variety of explanatory factors simultaneously. In particular, the models indicate the impacts of several driver behavior variables on the severity of the crashes, after controlling for a variety of other factors. For example, driver distraction (truck drivers), alcohol use (car drivers), and emotional factors (car drivers) are found to be associated with higher severity crashes. A further interesting finding is the strong statistical significance of several dummy variables that indicate missing data - these reflect how the nature of the crash itself could affect the completeness of the data. Future efforts should seek to collect such data more comprehensively so that the true effects of these aspects on the crash severity can be determined. Copyright © 2010 Elsevier Ltd. All rights reserved.

  17. The influence of daily sleep patterns of commercial truck drivers on driving performance.

    Science.gov (United States)

    Chen, Guang Xiang; Fang, Youjia; Guo, Feng; Hanowski, Richard J

    2016-06-01

    Fatigued and drowsy driving has been found to be a major cause of truck crashes. Lack of sleep is the number one cause of fatigue and drowsiness. However, there are limited data on the sleep patterns (sleep duration, sleep percentage in the duration of non-work period, and the time when sleep occurred) of truck drivers in non-work periods and the impact on driving performance. This paper examined sleep patterns of 96 commercial truck drivers during non-work periods and evaluated the influence these sleep patterns had on truck driving performance. Data were from the Naturalistic Truck Driving Study. Each driver participated in the study for approximately four weeks. A shift was defined as a non-work period followed by a work period. A total of 1397 shifts were identified. Four distinct sleep patterns were identified based on sleep duration, sleep start/end point in a non-work period, and the percentage of sleep with reference to the duration of non-work period. Driving performance was measured by safety-critical events, which included crashes, near-crashes, crash-relevant conflicts, and unintentional lane deviations. Negative binomial regression was used to evaluate the association between the sleep patterns and driving performance, adjusted for driver demographic information. The results showed that the sleep pattern with the highest safety-critical event rate was associated with shorter sleep, sleep in the early stage of a non-work period, and less sleep between 1 a.m. and 5 a.m. This study also found that male drivers, with fewer years of commercial vehicle driving experience and higher body mass index, were associated with deteriorated driving performance and increased driving risk. The results of this study could inform hours-of-service policy-making and benefit safety management in the trucking industry. Published by Elsevier Ltd.

  18. Feasibility of landfill gas as a liquefied natural gas fuel source for refuse trucks.

    Science.gov (United States)

    Zietsman, Josias; Bari, Muhammad Ehsanul; Rand, Aaron J; Gokhale, Bhushan; Lord, Dominique; Kumar, Sunil

    2008-05-01

    The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO2 WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO2). Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.

  19. How long-distance truck drivers and villagers in rural southeastern Tanzania think about heterosexual anal sex: a qualitative study

    NARCIS (Netherlands)

    Mtenga, S.; Shamba, D.; Wamoyi, J.; Kakoko, D.; Haafkens, J.; Mongi, A.; Kapiga, S.; Geubbels, E.

    2015-01-01

    Objective: To explore ideas of truck drivers and villagers from rural Tanzania about heterosexual anal sex (HAS) and the associated health risks. Methods: Qualitative study using 8 in-depth interviews (IDIs) and 2 focus group discussions (FGDs) with truck drivers and 16 IDIs and 4 FGDs with

  20. How long-distance truck drivers and villagers in rural southeastern Tanzania think about heterosexual anal sex: a qualitative study

    NARCIS (Netherlands)

    Mtenga, S.; Shamba, D.; Wamoyi, J.; Kakoko, D.; Haafkens, J.; Mongi, A.; Kapiga, S.; Geubbels, E.

    2015-01-01

    To explore ideas of truck drivers and villagers from rural Tanzania about heterosexual anal sex (HAS) and the associated health risks. Qualitative study using 8 in-depth interviews (IDIs) and 2 focus group discussions (FGDs) with truck drivers and 16 IDIs and 4 FGDs with villagers from the Morogoro

  1. 3 CFR - Imports of Certain Passenger Vehicle and Light Truck Tires From the People's Republic of China

    Science.gov (United States)

    2010-01-01

    ... vehicle and light truck tires from the People's Republic of China (China) are being imported into the... 3 The President 1 2010-01-01 2010-01-01 false Imports of Certain Passenger Vehicle and Light Truck... Presidential Determination No. 2009-28 of September 11, 2009 Imports of Certain Passenger Vehicle and Light...

  2. 75 FR 80430 - Passenger Car and Light Truck Average Fuel Economy Standards Request for Product Plan Information...

    Science.gov (United States)

    2010-12-22

    ... 533 [Docket No. NHTSA-2010-0175] Passenger Car and Light Truck Average Fuel Economy Standards Request... should be established for passenger cars and light trucks manufactured in model years 2017 and beyond... request is being issued in preparation for an upcoming Joint Notice of Proposed Rulemaking being...

  3. 49 CFR 542.2 - Procedures for selecting low theft light duty truck lines with a majority of major parts...

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Procedures for selecting low theft light duty truck lines with a majority of major parts interchangeable with those of a passenger motor vehicle line... TRUCK LINES TO BE COVERED BY THE THEFT PREVENTION STANDARD § 542.2 Procedures for selecting low theft...

  4. 75 FR 20005 - Crawler, Locomotive, and Truck Cranes Standard; Extension of the Office of Management and Budget...

    Science.gov (United States)

    2010-04-16

    ... Occupational Safety and Health Administration Crawler, Locomotive, and Truck Cranes Standard; Extension of the... collection requirements contained in its Crawler, Locomotive, and Truck Cranes Standard (29 CFR 1910.180... read or download through the Web site. All submissions, including copyrighted material, are available...

  5. 77 FR 41744 - Hand Trucks and Certain Parts Thereof From the People's Republic of China: Final Results of...

    Science.gov (United States)

    2012-07-16

    ... purposes of lifting and/or moving the load. That the vertical frame can be converted from a vertical... \\5/8\\ inch in diameter; hand trucks that use motorized operations either to move the hand truck from... revised the surrogate values for hot rolled steel coil, cold-rolled steel, polypropylene resin, slide bar...

  6. North American Free Trade Agreement : coordinated operational plan needed to ensure Mexican trucks' compliance with U.S. standards

    Science.gov (United States)

    2001-12-01

    In response to concerns about the safety of Mexican trucks, the General Accounting Office (GAO) was asked to examine (1) the extent to which Mexican-domiciled commercial trucks are likely to travel beyond U.S. border commercial zones once the border ...

  7. DEVELOPMENT OF SYSTEMS FOR SUPPORT OF OPEN-CAST DUMP TRUCK DRIVERS’ FITNESS TO WORK

    Directory of Open Access Journals (Sweden)

    V. V. Savchenko

    2006-01-01

    Full Text Available The paper considers the ways directed on improvement of drivers’ work efficiency and peculiarities of the executed algorithms of their activity. Several possibilities for the usage of algorithms and hardware-software means with the purpose to control development of emotional excitation of open-cast dump truck drivers are discussed in the paper. Such approach is presented as one of the possible ways intended to increase an efficiency of open-cast dump trucks functioning. It is based on minimization of negative aspects of so called «human factors» during the execution of algorithm activity by a driver.

  8. Finite element analysis of ROPS for mechanical driving dump truck cab

    Science.gov (United States)

    Wang, Yong; Xie, Heping; Fang, Yuanbin; Feng, Handui; Dong, Lei

    2018-02-01

    For roll-over protective structures (ROPS) in a mechanical driving dump truck cab, it simulates the lateral, vertical and longitudinal loads of ROPS. It obtains stress and deformation of the cab that occurs to roll. For the relative weak position of ROPS in the cab, the structure of the cab is improved and verified according to the ISO 3164: 1995. The results show that the established finite element model can effectively predict the deformation and stress distribution of ROPS, and optimize the weak structure of the cab, which has important guiding significance for structural design of the cab and ROPS optimization of the mechanical driving dump truck cab.

  9. Quantitative analysis of repairs actions occurring in industrial trucks in selected company

    Directory of Open Access Journals (Sweden)

    Karolina PROBIERZ

    2013-01-01

    Full Text Available Knowledge about the failures occurring during life cycle of technicalobjects, enables to take appropriate action, in order to avoid costs in the enterprise. In thepaper, the quantitative analysis of failures occurring in forklift truck in specific enterpriseis presented. The percentage of various types of actions being taken is presented. Paperpresents the number of action being taken per different systems of fork lift truck.Percentage of specific action in different subsystem, in relation to specific action in allsubsystems is also analyzed. Furthermore number of subsystem replacements actions inrelation to other action is illustrated on the chart.

  10. Experiment and Simulation of Medium-Duty Tactical Truck for Fuel Economy Improvement

    OpenAIRE

    Yeau-Jian Gene Liao; Allen M. Quail

    2011-01-01

    Fuel economy improvement on medium-duty tactical truck has and continues to be a significant initiative for the U.S. Army. The focus of this study is the investigation of Automated Manual Transmissions (AMT) and mild hybridization powertrain that have potential to improve the fuel economy of the 2.5-ton cargo trucks. The current platform uses a seven-speed automatic transmission. This study utilized a combination of on-road experimental vehicle data and analytical vehicle modeling and simulat...

  11. Forklift safety a practical guide to preventing powered industrial truck incidents and injuries

    CERN Document Server

    Swartz, George

    1999-01-01

    Written for the more than 1.5 million powered industrial truck operators and supervisors in general industry, as well as those in the construction and marine industries, this Second Edition provides an updated guide to training operators in safety and complying with OSHA's 1999 forklift standard. This edition of Forklift Safety includes a new chapter devoted to the new OSHA 1910.178 standard and new information regarding dock safety, narrow aisle trucks, off-dock incidents, tip-over safety, pallet safety, and carbon monoxide.

  12. The effect of transport time, season and position on the truck on stress response in rabbits

    OpenAIRE

    Liste, M.G; María, G. A.; García-Belenguer, S.; Chacón, G.; Gazzola, P.; Villarroel, M.

    2008-01-01

    The present study analyzed the effect of transport time, season and position on the truck on physiological stress response of commercial rabbits in Aragón (Spain). A total of 156 animals were sampled in a 2x2x3 factorial design testing two transport times: short, 1 hour (1hT) and long, 7 hours (7hT), in two different seasons: hot, during summer (HT) and cold during winter (CT), and three different positions on the truck: upper, middle or lower decks in multi-floor cages on rolling stands (MFR...

  13. Lack of HIV infection among truck drivers in Iran using rapid HIV test

    Directory of Open Access Journals (Sweden)

    Hossain Jabbari

    2010-01-01

    Full Text Available Background: The aim of this study was to evaluate the prevalence of HIV infection in Iranian long distance truck drivers using rapid HIV test. Methods: The study included 400 consecutive participants in Bazargan city, north-west of Iran in the late 2008 and the early 2009. Results: No HIV infection was observed among these long distance truck drivers. Conclusions: Although results of this study is plausible compared to other similar studies, repeated surveys are necessary to know the trend of HIV infection in truckers in Iran.

  14. Consistent Condom Use during Casual Sex among Long-Truck Drivers in Togo.

    Directory of Open Access Journals (Sweden)

    Issifou Yaya

    Full Text Available In 2008, the proportion of truck drivers who were not systematically protected during sex was 63% with casual partners and 60% with sex workers. Despite the high level of knowledge on HIV/AIDS and the growing awareness of the existence of the risk of HIV infection, condom use always encounters resistance among truck drivers in Togo. We sought to document the factors associated with condom use during casual sex among trucks' drivers in Togo.This was an analytical cross-sectional study conducted in 2010 and targeted truckers at truck station on the two main roads of Togo, Lomé-Cinkassé and Kodjoviakopé-Sanvee Condji.In this study, 1,782 trucks' drivers and their helpers were interviewed. All were men, and their mean age was 28.8 ± 8.8 years. Trucks' drivers were doing an average of 3 stops on their journeys and 1,229 (69% of them had at least two years of experience in the work. Of the 1,782 trucks' drivers, only 620 (34.8% had consistently used condoms during casual sex in the last three months. In multivariate analysis, predictors were: education level (primary schooling: OR = 1.54; p = 0.002; Secondary schooling and higher OR = 1.38; p = 0.036, good knowledge of ways of HIV transmission (OR = 1.53; p = 0.000, tested for HIV (OR = 1.67, p = 0.000, duration in the profession (2-5 years: OR = 1.43, p = 0.008; more than 5 years: OR = 1.38, p = 0.027, and HIV risk's perception (OR = 1.44, p = 0.000.These results highlight factors associated with consistent condom use during casual sex by truck drivers in Togo. This is a key population group at high risk of HIV transmission toward which the national HIV/AIDS control program should strengthen the HIV prevention strategies.

  15. Structural safety evaluation of the K Basin railcar and truck applications

    International Nuclear Information System (INIS)

    Winkel, B.V.

    1995-08-01

    There are two rail spurs in the storage/transfer areas of both the K East and K West fuel storage basins. These rail spurs both end at the west edge of the basins. To avoid accidental entry of a railcar into a basin, administrative procedures and rail control hardware have been provided. Based upon a combination of historical documentation and existing adminstrative controls, a maximum credible impact accident was established. Using this design basis accident, the existing rail control hardware was evaluated for structural adequacy. The K Basin rail spurs are embedded in concrete, which permits truck/trailer entry into the same area. Safety issues for truck applications are also addressed

  16. Simulation Study on Hot Stamping Forming of the Drive Axle Housing of Heavy Truck

    Science.gov (United States)

    Dai, Yongqian; Ji, Jianyi; Luo, Lingjiang

    2018-01-01

    Aiming at the national energy-saving and emission reduction requirements, lightweight of the heavy truck is imminent. Several parameters related to hot stamping forming process of heavy truck drive axle housing are studied in this paper. The results show that the existing two-step stamping with air cooling molding process, can be improved into one-step hot stamping process. The initial temperature of the blank, stamping speed and other parameters related to the forming process were optimized. The results provides useful reference for improving the existing forming process of the drive axle housing, and it is also helpful for realizing the lightweight design of drive axle housing.

  17. Scenarios for the future; Framtidsscenarier

    Energy Technology Data Exchange (ETDEWEB)

    Haegermark, H.; Bergmark, M.

    1995-06-01

    This project aims primarily to give a basis for the joint R and D program for the Swedish electric utility industry, in the form of pictures of the future up to 2020. The work was performed during four seminars in a group of managers and R and D planners. The four scenarios differ mainly in the assumptions of high or low economic growth and on market or political rule. Assumptions on essential uncertainties about the future have been combined in a consistent manner, e.g. on the structure of the utility industry, the role of nuclear power, the importance of the greenhouse gas issue, the influence of new technology developments and on changes of values in society. Certain other development appear in all scenarios, e.g. the impact of information technology throughout society, the internationalization of business in general and industrial production in particular, considerations for the environment and care for natural resources. The four scenarios are: `Technology on the throne` (market rule/high growth); `Intense competition` (market rule/low growth); `Monopoly takes over` (political rule/high growth); and `Green local society` (political rule/low growth). Some of the important factors pointed out by the study are: Increased customer mobility between regions and countries; The impact of information technology; Societal value changes; Sustainable development as an important driving force; Structure of the utility industry. Diversifying into new services. New players; Access to knowledge and competence; Ways for handling the greenhouse gas problem; Preparedness for nuclear power phase-out. 12 figs, 6 tabs

  18. The truck of the future. Saving of fuel and CO2-reduction in the year 2013; De truck van de toekomst. Brandstof- en CO2-besparing anno 2013

    Energy Technology Data Exchange (ETDEWEB)

    Van Mensch, P.; Vonk, W.; Verbeek, R. [TNO, Delft (Netherlands)

    2013-06-15

    Within the demonstration program 'Truck of the Future' ten fuel saving measures were tested and evaluated in transportation businesses. These measures are divided into the following categories: Rolling friction mitigation measures; Drag mitigation measures; ICT systems aimed at improving economical driving. All measures investigated for specific situations resulted in considerable saving. In the report also payback period and the experiences of participating transport businesses are included [Dutch] Binnen het demonstratieprogramma 'Truck van de Toekomst' zijn een tiental brandstofbesparende maatregelen toegepast bij transportbedrijven en geevalueerd. Deze maatregelen zijn opgesplitst in de volgende categorieen: Rolweerstand verlagende maatregelen; Luchtweerstand verlagende maatregelen; ICT-systemen gericht op het verbeteren van zuinig rijgedrag. Alle onderzochte maatregelen hebben in specifieke gebruikssituaties een duidelijk waarneembare besparing opgeleverd. In de rapportage worden ook de terugverdientijd en de gebruikservaringen van de deelnemende transportbedrijven meegenomen.

  19. Comparing recent uranium supply scenarios

    International Nuclear Information System (INIS)

    Arnold, N.; Gufler, K.

    2014-01-01

    For more than one decade – even after the Fukushima accidents - an increase in global nuclear energy generation capacity is widely expected. At the same time a variety of uranium supply scenarios were published by industry, academics or international organizations, drawing different pictures of future uranium supply. They were created with the background of a uranium market facing several challenges. First an excursion in the uranium market price, in 2007, then reduced nuclear growth expectations after 2011, at least in non-Asian countries, also implying considerable changes to the supply side. For this publication a meta-study was carried out identifying, evaluating and comparing different recent scenarios on the availability of uranium. While there are some differences in the frame conditions (e.g. the expected uranium demand, the time fame, the considered mining projects,..), there are also notable similarities in these scenarios. This concerns long lead times for mine openings as well as the dependence on large mining projects (e.g. Olympic Dam, Cigar Lake). Generally, a decline in production in about 10 years is assumed, and thus the necessity of the timely development of mining projects is pointed out. In addition the omission of uranium from Russian nuclear weapons and the chances of keeping the changes in secondary supplies in balance with primary production have been widely discussed. Here, the production growth in Kazakhstan but also the role of the current market situation are central aspects. As another aspect the possible contribution from unconventional resources is of interest, particularly against the background of rising production costs for conventional resources. Finally, it shall be reflected how well older scenarios were able to map the reality and which trends could or could not be anticipated. It is relevant to identify which aspects in the development of mining capacities are essential for security of supply, and can therefore be regarded

  20. TCL2 Ocean Scenario Replay

    Science.gov (United States)

    Mohlenbrink, Christoph P.; Omar, Faisal Gamal; Homola, Jeffrey R.

    2017-01-01

    This is a video replay of system data that was generated from the UAS Traffic Management (UTM) Technical Capability Level (TCL) 2 flight demonstration in Nevada and rendered in Google Earth. What is depicted in the replay is a particular set of flights conducted as part of what was referred to as the Ocean scenario. The test range and surrounding area are presented followed by an overview of operational volumes. System messaging is also displayed as well as a replay of all of the five test flights as they occurred.

  1. Scenario testing using formal ontologies

    CSIR Research Space (South Africa)

    Harmse, HF

    2014-09-01

    Full Text Available project that has been done for a South African hotel group where scenario testing has been employed to detect and rectify errors during the requirements phase of the SDLC. In the hospitality industry the business requirements around calculating the rate.... Firstly a flat rate can be charged across all rooms in the hotel. Secondly the rate can be charged based on the number of guests who form part of the booking. In the hospitality industry this is often referred to as PAX. Lastly the rate can be determined...

  2. Estimating the supply and demand for commercial heavy truck parking on interstate highways : a case study of I-81 in Virginia.

    Science.gov (United States)

    2002-01-01

    The increasing number of trucks traveling on Virginia highways has led to a growing demand for public rest areas and private truck stops. This study developed a methodology to determine the supply and demand for commercial heavy truck parking using I...

  3. Evaluation of World Energy Scenarios

    Directory of Open Access Journals (Sweden)

    Valery I. Salygin

    2016-01-01

    Full Text Available What are the future global systems developments? It remains one the biggest unknown, especially in terms of energy, as it is globally considered as both cause and solution for multiple problems of the humanity. Therefore, nowadays a number of experts are exploring driving forces, critical uncertainties and unknowns that have an influence on future energy systems development. This article aims at providing a brief investigation of existing world energy scenarios that cover the range of plausible outcomes of future global energy system development. Those are represented by International Energy Agency, World Energy Council, Organization of the Petroleum Exporting Countries, and others. The analysis covers both qualitative and quantitative indicators of the world energy system development that provide for future worldview formation. The article looks into various approaches to energy system development forecasting and scenario building employed by the abovementioned organisations, and discovers the motives for making assumptions as the means of attaining internal targets and the consequences of the distinction of individual attitude to the development trends within the expert community. The current assessment implies grouping of the most advanced of the existing energy system development models, identification their advantages and disadvantages, and shows differences in modeling approaches used in a number of specialized international organisations.

  4. Scenario Development for Information Operations (IO) Experimentation

    Science.gov (United States)

    2003-07-10

    country called DYSLEXIA , whose government has been making threats to invade and appropriate a region of its neighbouring country, ABSTEMIA, which is...Network Measures and Metrics 18 Conclusion Scenarios - Tailoring, Framework, Families of Scenario Experiments - Measures, Humans, Objectives Networks

  5. The association between adolescent entry into the trucking industry and risk of HIV among long-distance truck drivers in India

    Directory of Open Access Journals (Sweden)

    Mishra RM

    2012-09-01

    Full Text Available Ram Manohar Mishra,1 Madhulika Dube,2 Niranjan Saggurti,1 Arvind Pandey,3 Bidhubhusan Mahapatra,1 Sowmya Ramesh11Population Council, New Delhi, 2Department of Statistics, Maharshi Dayanand University, Rohtak, Haryana, 3National Institute of Medical Statistics, Indian Council of Medical Research, New Delhi, IndiaAbstract: This study examines the relationship between entry into the trucking industry during adolescence and both sexually transmitted infections (STIs and infection by the human immunodeficiency virus (HIV among long-distance truck drivers in India. Data were sourced from a cross-sectional survey (sample size: 2066 undertaken in 2007 among long-distance truck drivers. The survey spread across major transshipment locations covering the bulk of India's transport volume along four routes. Participants were interviewed about sexual behaviors and were tested for HIV and STIs. The present authors constructed two synthetic cohorts based on the participants' duration of employment in the trucking industry: (1 low (duration ≤ 6 years and (2 high experience (duration ≥ 7 years. Based on age at entry into the trucking industry, participants were termed as either adolescent (age at entry < 18 complete years or adult entrants (age at entry ≥ 18 complete years. In the low-experience cohort, the adolescent entrants were more likely than the adult entrants to have sex with paid female partners (42.6% versus 27.2%, respectively; adjusted odds ratio [OR]: 1.9; 95% confidence interval [CI]: 1.3–2.9 and to practice inconsistent condom use with such partners (69.1% versus 26.8%, respectively; adjusted OR: 5.3; 95% CI: 2.4–11.6. However, no significant differences were found in STI and HIV prevalence between the adolescent and the adult entrants in this cohort. In the high-experience cohort, the adolescent entrants were about two times more likely than the adult entrants to practice inconsistent condom use with paid female partners (38.5% versus

  6. Development and Change through Scenario Planning

    Science.gov (United States)

    Chermack, Thomas J.; Walton, John S.

    2004-01-01

    This paper examines the role of scenario planning as a development and change intervention. To do so, this article provides an overview of scenario planning and an overview of development and change in organizations. The article then builds on the philosophical orientations of development and change through scenario planning introducing the…

  7. Truck sideguards for Vision Zero : review and technical recommendations for Safe Fleet Transition Plan pilot deployment.

    Science.gov (United States)

    2014-12-01

    Large truck crashes are more likely to result in a pedestrian or bicyclist fatality than crashes involving passenger vehicles and are more likely to be side-impact crashes. Sideguards are vehicle-based safety devices that help prevent pedestrians and...

  8. Shock and vibration environments for a large shipping container during truck transport (Part II)

    International Nuclear Information System (INIS)

    Magnuson, C.E.

    1978-05-01

    Purpose of this study was to obtain vibration and shock data during truck shipment of heavy cargo. These data were for use in determining any trends of vibration and shock environments with increased cargo weight. The new data were obtained on a ''piggyback'' basis during truck transport of 249 100N (56,000-pound) cargo which consisted of a spent fuel container and its supporting structure. The truck was driven from Mercury, Nevada, to Albuquerque, New Mexico. The routes traveled were US 95 from Mercury, Nevada, to Las Vegas, Nevada; US 93 from Las Vegas to Kingman, Arizona; and I-40/US 66 from Kingman to Albuquerque, New Mexico. Speeds varied from very slow to 88 km/hr (55 mph). A comparison of data from similar experiments with cargo weights varying from no-load to this load shows that the zero-to-peak acceleration amplitude levels of vibration are highest when trucks carry relatively light loads. This is true for the longitudinal and vertical axes of the vehicles in most frequency bands and for the transverse axis above 700 Hz. The shock response acceleration amplitudes for heavier cargo weights were less severe above 3 Hz in the vertical axis and higher between 8 and 20 Hz in the transverse axis. The highest acceleration amplitude of shock response in the longitudinal axis below about 20 Hz was produced in a trailer having a spring suspension system and carrying the 249 100N (56,000 pounds) load

  9. Research on hydraulic system of KZC-5 type rear dump truck in underground mine

    International Nuclear Information System (INIS)

    Lei Zeyong

    2005-01-01

    KZC-5 type rear dump truck in underground mine is introduced in this paper. The determining principles and ways of two main hydraulic systems are discussed. It has been proved that the hydraulic systems are reasonable in the industrial scale test. (author)

  10. Optimizing freight routes and modes to minimize environmental impacts : integrating truck emissions cost in traffic assignment.

    Science.gov (United States)

    2014-10-01

    Adverse impacts of greenhouse gasses (GHG) and the imperative for reducing the production are well established. The : transportation sector accounts for 28% of all U.S. GHG production. Heavy-duty vehicles (e.g., large freight trucks) account for : ne...

  11. 76 FR 25761 - Commercial Driver's License (CDL) Standards; Volvo Trucks North America, Renewal of Exemption

    Science.gov (United States)

    2011-05-05

    ... TRANSPORTATION Federal Motor Carrier Safety Administration Commercial Driver's License (CDL) Standards; Volvo... from the requirement to hold a commercial driver's license (CDL) sought by Volvo Trucks North America (Volvo) on behalf of five employees. Volvo requested renewal of the CDL exemption for five Swedish...

  12. Design/Operations review of core sampling trucks and associated equipment

    International Nuclear Information System (INIS)

    Shrivastava, H.P.

    1996-01-01

    A systematic review of the design and operations of the core sampling trucks was commissioned by Characterization Equipment Engineering of the Westinghouse Hanford Company in October 1995. The review team reviewed the design documents, specifications, operating procedure, training manuals and safety analysis reports. The review process, findings and corrective actions are summarized in this supporting document

  13. An Optimisation Approach Applied to Design the Hydraulic Power Supply for a Forklift Truck

    DEFF Research Database (Denmark)

    Pedersen, Henrik Clemmensen; Andersen, Torben Ole; Hansen, Michael Rygaard

    2004-01-01

    -level optimisation approach, and is in the current paper exemplified through the design of the hydraulic power supply for a forklift truck. The paper first describes the prerequisites for the method and then explains the different steps in the approach to design the hydraulic system. Finally the results...

  14. Finite element simulation of truck impacts on highway bridge piers : final report.

    Science.gov (United States)

    2016-04-01

    Recent studies show that the dynamic forces because of truck impacts may be significantly higher than the : 600kips force recommended by the AASHTO. Hence, there is a need to carry out detailed investigations : on vehicular-bridge collision for a rel...

  15. An analysis of health promotion materials for Dutch truck drivers: Off target and too complex?

    Science.gov (United States)

    Boeijinga, Anniek; Hoeken, Hans; Sanders, José

    2017-01-01

    Despite various health promotion initiatives, unfavorable figures regarding Dutch truck drivers' eating behaviors, exercise behaviors, and absenteeism have not improved. The aim was to obtain a better understanding of the low level of effectiveness of current health interventions for Dutch truck drivers by examining to what extent these are tailored to the target group's particular mindset (focus of content) and health literacy skills (presentation of content). The article analyzes 21 health promotion materials for Dutch truck drivers using a two-step approach: (a) an analysis of the materials' focus, guided by the Health Action Process Approach; and (b) an argumentation analysis, guided by pragma-dialectics. The corpus analysis revealed: (a) a predominant focus on the motivation phase; and (b) in line with the aim of motivating the target group, a consistent use of pragmatic arguments, which were typically presented in an implicit way. The results indicate that existing health promotion materials for Dutch truck drivers are not sufficiently tailored to the target group's mindset and health literacy skills. Recommendations are offered to develop more tailored/effective health interventions targeting this high-risk, underserved occupational group.

  16. 75 FR 11916 - Chrysler LLC, Manufacturing Truck and Activity Division, Jefferson North Assembly Plant...

    Science.gov (United States)

    2010-03-12

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-63,000] Chrysler LLC, Manufacturing Truck and Activity Division, Jefferson North Assembly Plant, Including On-Site Leased Workers From Technical Engineering Consultants, Inc. and, Caravan Knight Facilities Management: Detroit, MI; Amended Certification Regarding Eligibility To Appl...

  17. Beyond Racism and Poverty : The Truck System on Louisiana Plantations and Dutch peateries, 1865-1920

    NARCIS (Netherlands)

    Lurvink, K.

    The truck system was a global phenomenon in the period 1865-1920, where workers were paid through the company store. In Beyond Racism and Poverty Karin Lurvink looks at how this system functioned on plantations in Louisiana in comparison with peateries in the Netherlands. In the United States, the

  18. Sizing stack and battery of a fuel cell hybrid distribution truck

    NARCIS (Netherlands)

    Bram Veenhuizen; P. van den Bosch; T. Hofman; Edwin Tazelaar; Y. Shen

    2012-01-01

    An existing fuel cell hybrid distribution truck, built for demonstration purposes, is used as a case study to investigate the effect of stack (kW) and battery (kW, kWh) sizes on the hydrogen consumption of the vehicle. Three driving cycles, the NEDC for Low Power vehicles, CSC and JE05 cycle, define

  19. Effectiveness of Health Promotion Programmes for Truck Drivers: A Systematic Review

    Science.gov (United States)

    Ng, Mandy K.; Yousuf, Bilal; Bigelow, Philip Lloyd; Van Eerd, Dwayne

    2015-01-01

    Objective: To review the characteristics of effective health promotion interventions for reducing chronic diseases and their risk factors in truck drivers. Methods: MEDLINE (PubMed), SCOPUS, Web of Science Conference Proceedings, CINAHL (Cumulative Index to Nursing and Allied Health Literature), and the National Transportation Library were…

  20. Truck-involved crashes injury severity analysis for different lighting conditions on rural and urban roadways.

    Science.gov (United States)

    Uddin, Majbah; Huynh, Nathan

    2017-11-01

    This paper investigates factors affecting injury severity of crashes involving trucks for different lighting conditions on rural and urban roadways. It uses 2009-2013 Ohio crash data from the Highway Safety Information System. The explanatory factors include the occupant, vehicle, collision, roadway, temporal and environmental characteristics. Six separate mixed logit models were developed considering three lighting conditions (daylight, dark, and dark-lighted) on two area types (rural and urban). A series of log-likelihood ratio tests were conducted to validate that these six separate models by lighting conditions and area types are warranted. The model results suggest major differences in both the combination and the magnitude of impact of variables included in each model. Some variables were significant only in one lighting condition but not in other conditions. Similarly, some variables were found to be significant in one area type but not in other area type. These differences show that the different lighting conditions and area types do in fact have different contributing effects on injury severity in truck-involved crashes, further highlighting the importance of examining crashes based on lighting conditions on rural and urban roadways. Age and gender of occupant (who is the most severely injured in a crash), truck types, AADT, speed, and weather condition were found to be factors that have significantly different levels of impact on injury severity in truck-involved crashes. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Comparisons of Traffic Collisions between Expressways and Rural Roads in Truck Drivers

    Directory of Open Access Journals (Sweden)

    Sangbok Lee

    2016-03-01

    Conclusion: This study can be used as a guideline and a base line to develop a plan of action to prevent traffic accidents. It can also help to prepare formal regulations about a truck driver's vehicle maintenance and driving attitude for a precaution on road accidents.

  2. 19 CFR 123.92 - Electronic information for truck cargo required in advance of arrival.

    Science.gov (United States)

    2010-04-01

    ... foreign country. Cargo arriving by truck in transit through the United States from one foreign country to... point to another in the same foreign country (§ 123.31(b); § 123.42) are subject to the advance... complete name and address, or identification number, from the bill(s) of lading (for each house bill in a...

  3. Stressful work, psychological job strain, and turnover: A 2-year prospective cohort study of truck drivers

    NARCIS (Netherlands)

    Croon, E.M.de; Sluiter, J.K.; Blonk, R.W.B.; Broersen, J.P.J.; Frings-Dresen, M.H.W.

    2004-01-01

    Based on a model that combines existing organizational stress theory and job transition theory, this 2-year longitudinal study examined antecedents and consequences of turnover among Dutch truck drivers. For this purpose, self-reported data on stressful work (job demands and control), psychological

  4. Analysis of Maintenance Service Contracts for Dump Trucks Used in Mining Industry with Simulation Approach

    Science.gov (United States)

    Dymasius, A.; Wangsaputra, R.; Iskandar, B. P.

    2016-02-01

    A mining company needs high availability of dump trucks used to haul mining materials. As a result, an effective maintenance action is required to keep the dump trucks in a good condition and hence reducing failure and downtime of the dump trucks. To carry out maintenance in-house requires a high intensive maintenance facility and high skilled maintenance specialists. Often, outsourcing maintenance is an economic option for the company. An external agent takes a proactive action with offering some maintenance contract options to the owner. The decision problem for the owner is to decide the best option and for the agent is to determine the optimal price for each option offered. A non-cooperative game-theory is used to formulate the decision problems for the owner and the agent. We consider that failure pattern of each truck follows a non-homogeneous Poisson process (NHPP) and a queueing theory with multiple servers is used to estimate the downtime. As it involves high complexity to model downtime using a queueing theory, then in this paper we use a simulation method. Furthermore, we conduct experiment to seek for the best number of maintenance facilities (servers) which minimises maintenance and penalty costs incurred to the agent.

  5. Evaluation of alternative truck lane management strategies along a section of I-81.

    Science.gov (United States)

    2010-05-01

    I-81 is one of the top eight truck routes in the U.S. In the state of Virginia, I-81 traverses 325.51 miles from : Tennessee in the south to the West Virginia border in the north and passes through 12 counties. The highway : was designed for a 15 per...

  6. Study on an Interactive Truck Crane Simulation Platform Based on Virtual Reality Technology

    Science.gov (United States)

    Sang, Yong; Zhu, Yu; Zhao, Honghua; Tang, Mingyan

    2016-01-01

    The modern web-based distance education overcomes space-time restriction of the traditional teaching forms. However, being short of specifically observable and operable experimental equipment makes the web-based education lack advantages in the knowledge learning progress, which needs strong stereoscopic effect and operability. Truck crane is the…

  7. Biomechanical investigation of prolonged driving in an ergonomically designed truck seat prototype.

    Science.gov (United States)

    Cardoso, Michelle; McKinnon, Colin; Viggiani, Dan; Johnson, Michel J; Callaghan, Jack P; Albert, Wayne J

    2018-03-01

    A postural evaluation during a prolonged driving task was conducted to determine the ergonomic validity of a new freely adjustable truck seat prototype. Twenty participants were recruited to perform two 2-h simulated driving sessions. Postures were assessed using motion capture, accelerometers and pressure pads. Subjective discomfort was also monitored in 15-min increments using ratings of perceived discomfort (RPD) and the Automotive Seating Discomfort Questionnaire. Participants had a more neutral spine posture during the first hour of the drive and reported lower RPDs while sitting in the prototype. Pairing the gluteal backrest panel with the adjustable seat pan helped reduce the average sitting pressure. The industry-standard truck seat may lead to the development of poor whole body posture, and the proposed ergonomic redesign of a new truck seat helped improve sitting posture and reduce perceived discomfort. Practitioner Summary: A new freely adjustable truck seat prototype was compared to an Industry standard seat to assess hypothesised improvements to sitting posture and discomfort for long haul driving. It was found that the adjustable panels in the prototype helped promote spine posture, reduce sitting pressure and improved discomfort ratings.

  8. Truck parking : an emerging safety hazard to highway users : final report - draft.

    Science.gov (United States)

    2017-07-01

    It is recognized nationwide that commercial motor vehicle operators are often unable to find safe and adequate parking to meet hours-of-service (HOS) regulations. This holds true in Oregon, where high-use corridor rest areas and truck stops are exper...

  9. Determinants of Safe and Productive Truck Driving: Empirical Evidence from Long-haul Cargo Transport

    NARCIS (Netherlands)

    de Vries, J.; de Koster, R.; Rijsdijk, S.; Roy, D.

    2017-01-01

    Using GPS data of 370 long-haul trips in India, survey data of 49 truck drivers, and ERP data, this study examines the role of driver personality characteristics in predicting risky and productive driving. The results show that more conscientious drivers display more risky driving behavior. More

  10. Evaluation of the fuel-conservation potential of truck aerodynamic-drag-reduction devices

    Energy Technology Data Exchange (ETDEWEB)

    1976-06-30

    A study of commercially available and prototype aerodynamic drag reduction devices which can be retrofitted onto this nation's trucks to achieve significant fuel savings by 1980 was conducted. The results of the study are presented in seven sections. An overview of the basic study results is given in the Summary Section, and a brief introduction to the general nature of the truck drag problem and the study scope is contained in Section 1. Section 2 provides a more detailed discussion of the aerodynamic drag problem and the characteristics of specific retrofit aerodynamic drag reduction devices which are in the production or prototype status. The results of a survey of fleet owners utilizing aerodynamic drag reduction devices and their experience with regard to fuel savings and operational factors are given in Section 3. Section 4 contains the results of economic analyses made to determine the cost-benefit effects of drag reduction devices. An analysis of the US truck population to which such drag reduction devices may be applicable and the fuel savings potential attendant to their use is given in Section 5. The significant elements of a program structured to encourage the utilization of aerodynamic drag reduction devices on trucks are defined in Section 6.

  11. The determinants of fuel use in the trucking industry - volume, fleet characteristics and the rebound effect

    DEFF Research Database (Denmark)

    de Borger, Bruno; Mulalic, Ismir

    2012-01-01

    more fuel efficient, trucks. Third, these adjustments and the rebound effect jointly imply that the effect of higher fuel prices on fuel use in the trucking industry is fairly small; estimated price elasticities are _0:13 and _0:22 in the short run and in the long run, respectively. The empirical......This paper studies the determinants of fuel use in the trucking industry in Denmark, using aggregate time series data for the period 1980–2007. The model captures the main linkages between the demand for freight transport, the characteristics of the vehicle fleet, and the demand for fuel. Results...... of this effect is approximately 10% in the short run and 17% in the long run, so that a 1% improvement in fuel efficiency reduces fuel use by 0.90% (short-run) to 0.83% (long-run). Second, we find that higher fuel prices raise the average capacity of trucks, and they induce firm sto invest in newer, typically...

  12. HIV risk behaviors differ by workplace stability among Mexican female sex workers with truck driver clientele.

    Science.gov (United States)

    Chen, Nadine E; Strathdee, Steffanie A; Rangel, Gudelia; Patterson, Thomas L; Uribe-Salas, Felipe J; Rosen, Perth; Villalobos, Jorge; Brouwer, Kimberly C

    2012-12-28

    In a study of female sex workers (FSW) servicing truck driver clients in Mexican border cities, we evaluated differences in HIV/STI risk behaviors by workplace. Cross-sectional study of FSW servicing truck drivers in Mexico: 100 from Nuevo Laredo (U.S. border); 100 from Ciudad Hidalgo (Guatemalan border). Main outcome was unstable workplace, defined as primary place of sex work in a public place (street, vehicle, gas station, etc.) vs. stable workplace (bar, brothel, and hotel). Logistic regression was used to identify correlates associated with trading sex at unstable workplaces in the last month. Of the FSW surveyed, 18% reported an unstable workplace. The majority of FSW surveyed were young (trend towards lower condom use self-efficacy scores (OR 0.8 per unit increase, 95%CI 0.7-1.0). On multivariate regression, unstable workplace was associated with having majority/all truck driver clientele, being surveyed in Nuevo Laredo, and decreased odds of ever having an HIV test. Among Mexican FSW with truck driver clients, providing safe indoor spaces for sex work may help facilitate public health interventions that improve HIV/STI and reproductive health outcomes.

  13. The impact of hybrid engines on fuel consumption and emissions of heavy-duty trucks

    NARCIS (Netherlands)

    Bal, F; Vleugel, J.M.; Brebbia, CA; Sendra, J

    2017-01-01

    Overland transport of goods mainly goes by road. Road freight transport, trucking in particular, has a large share in the energy consumption, CO2-emissions and air pollution by human activities. This will become an even bigger issue with the expected massive growth of road freight

  14. 49 CFR 176.78 - Use of power-operated industrial trucks on board vessels.

    Science.gov (United States)

    2010-10-01

    ...-operated shut off valve closed before the quick disconnect fitting to the fuel tank is disconnected. (3) A... Laboratories. Any repair or alteration to a truck must be equivalent to that required on the original... the exhaust, fuel, and electrical systems. (6) An “LP” designated unit is similar to a “G” unit except...

  15. Development of a portable remote sensing system for measurement of diesel emissions from passing diesel trucks.

    Science.gov (United States)

    2011-04-08

    A wireless remote-sensing system has been developed for measurement of NOx and particulate matters (PM) emissions from passing diesel trucks. The NOx measurement system has a UV light source with quartz fiber optics that focused the light source into...

  16. Truck frame welding reparation by steel covered electrodes with varied amount of Ni and Mo

    Directory of Open Access Journals (Sweden)

    Tomasz WĘGRZYN

    2010-01-01

    Full Text Available This paper attempts to study safety and exploitation conditions of weld steel structure reparation of car body truck frames. Car (auto body is the name given to the portion of an automobile which gives it shape. The work is a theoretical investigation and concentrates on structural integrity and vehicle safety after the reparation welding of truck frames. To study the effects of the frame flexibility and resistance, the truck frame has been welded by steel electrodes with varied amount of Ni and Mo. The most significant of factors influencing that conditions are connected with material choice, welding technology, state of stress and temperature. Because of that a good selection of steel and welding method is crucial to obtain proper steel structure. Shielded metal arc welding (SMAW is a very popular method of welding used for car body reparation. Car body elements of higher durability are made of low carbon and low alloy steel, very often with small amount of carbon and the amount of alloy elements such as Ni, Mn, Mo, Cr, Ti, Al, V in low alloy steel and their welds. In the paper only the influence of the variable amounts of nickel, molybdenum on impact and fatigue properties of low alloy metal weld deposit was tested. The results show that there is good agreement between proper chemical composition of weld metal deposit (WMD and truck structure properties.

  17. Commercial Trucking: Safety and Infrastructure Issues Under the North American Free Trade Agreement

    Science.gov (United States)

    1996-02-29

    The North American Free Trade Agreement (NAFTA) provided for the U.S.-Mexican border to be opened for increased commercial truck traffic within the respective border states-four in the United States (Arizona, California, New Mexico, and Texas) and si...

  18. Optimal routes scheduling for municipal waste disposal garbage trucks using evolutionary algorithm and artificial immune system

    Directory of Open Access Journals (Sweden)

    Bogna MRÓWCZYŃSKA

    2011-01-01

    Full Text Available This paper describes an application of an evolutionary algorithm and an artificial immune systems to solve a problem of scheduling an optimal route for waste disposal garbage trucks in its daily operation. Problem of an optimisation is formulated and solved using both methods. The results are presented for an area in one of the Polish cities.

  19. 76 FR 20807 - Pilot Program on NAFTA Long-Haul Trucking Provisions

    Science.gov (United States)

    2011-04-13

    .... Trucking issues at the United States-Mexico border were not fully addressed until NAFTA was negotiated in... in the NAFTA. On February 6, 2001, the Arbitration Panel issued its final report and ruled in Mexico..., Mexico announced that it was exercising its rights under the 2001 NAFTA Arbitration Panel decision to...

  20. 76 FR 63988 - Pilot Project on NAFTA Trucking Provisions; Pre-Authorization Safety Audits

    Science.gov (United States)

    2011-10-14

    ...-0097] Pilot Project on NAFTA Trucking Provisions; Pre-Authorization Safety Audits AGENCY: Federal Motor... demonstrate the ability of Mexico- domiciled motor carriers to operate safely in the United States beyond the commercial zones on the United States-Mexico border. This action is required by the ``U.S. Troop Readiness...

  1. Detroit Diesel Engine Technology for Light Duty Truck Applications - DELTA Engine Update

    Energy Technology Data Exchange (ETDEWEB)

    Freese, Charlie

    2000-08-20

    The early generation of the DELTA engine has been thoroughly tested and characterized in the virtual lab, during engine dynamometer testing, and on light duty trucks for personal transportation. This paper provides an up-to-date account of program findings. Further, the next generation engine design and future program plans will be briefly presented.

  2. Grand unified brane world scenario

    Science.gov (United States)

    Arai, Masato; Blaschke, Filip; Eto, Minoru; Sakai, Norisuke

    2017-12-01

    We present a field theoretical model unifying grand unified theory (GUT) and brane world scenario. As a concrete example, we consider S U (5 ) GUT in 4 +1 dimensions where our 3 +1 dimensional spacetime spontaneously arises on five domain walls. A field-dependent gauge kinetic term is used to localize massless non-Abelian gauge fields on the domain walls and to assure the charge universality of matter fields. We find the domain walls with the symmetry breaking S U (5 )→S U (3 )×S U (2 )×U (1 ) as a global minimum and all the undesirable moduli are stabilized with the mass scale of MGUT. Profiles of massless standard model particles are determined as a consequence of wall dynamics. The proton decay can be exponentially suppressed.

  3. Cancer care scenario in Bangladesh

    Directory of Open Access Journals (Sweden)

    A. F. M. Kamal Uddin

    2013-01-01

    Full Text Available Bangladesh is a developing country that is facing many challenges, especially in the health sector. Cancer management is a priority due to the current trend of increased incidence in this region. In this article, the current scenario of cancer in Bangladesh and its management with brief history is outlined. The combined effort of government and private sector is highlighted with the gradual progress in cancer management. Recent introduction of the state-of-the-art facilities and the training facilities for human resource development are also outlined. The existing challenges and cooperation from local NGOs and other overseas sources are also highlighted to provide an insight regarding possible ways to tackle these challenges to ensure a better future.

  4. Cancer care scenario in Bangladesh.

    Science.gov (United States)

    Uddin, A F M Kamal; Khan, Zohora Jameela; Islam, Johirul; Mahmud, Am

    2013-04-01

    Bangladesh is a developing country that is facing many challenges, especially in the health sector. Cancer management is a priority due to the current trend of increased incidence in this region. In this article, the current scenario of cancer in Bangladesh and its management with brief history is outlined. The combined effort of government and private sector is highlighted with the gradual progress in cancer management. Recent introduction of the state-of-the-art facilities and the training facilities for human resource development are also outlined. The existing challenges and cooperation from local NGOs and other overseas sources are also highlighted to provide an insight regarding possible ways to tackle these challenges to ensure a better future.

  5. Radiation Detection Computational Benchmark Scenarios

    Energy Technology Data Exchange (ETDEWEB)

    Shaver, Mark W.; Casella, Andrew M.; Wittman, Richard S.; McDonald, Ben S.

    2013-09-24

    Modeling forms an important component of radiation detection development, allowing for testing of new detector designs, evaluation of existing equipment against a wide variety of potential threat sources, and assessing operation performance of radiation detection systems. This can, however, result in large and complex scenarios which are time consuming to model. A variety of approaches to radiation transport modeling exist with complementary strengths and weaknesses for different problems. This variety of approaches, and the development of promising new tools (such as ORNL’s ADVANTG) which combine benefits of multiple approaches, illustrates the need for a means of evaluating or comparing different techniques for radiation detection problems. This report presents a set of 9 benchmark problems for comparing different types of radiation transport calculations, identifying appropriate tools for classes of problems, and testing and guiding the development of new methods. The benchmarks were drawn primarily from existing or previous calculations with a preference for scenarios which include experimental data, or otherwise have results with a high level of confidence, are non-sensitive, and represent problem sets of interest to NA-22. From a technical perspective, the benchmarks were chosen to span a range of difficulty and to include gamma transport, neutron transport, or both and represent different important physical processes and a range of sensitivity to angular or energy fidelity. Following benchmark identification, existing information about geometry, measurements, and previous calculations were assembled. Monte Carlo results (MCNP decks) were reviewed or created and re-run in order to attain accurate computational times and to verify agreement with experimental data, when present. Benchmark information was then conveyed to ORNL in order to guide testing and development of hybrid calculations. The results of those ADVANTG calculations were then sent to PNNL for

  6. Caminhoneiros de rota curta e sua vulnerabilidade ao HIV, Santos, SP Vulnerability to HIV and AIDS of short distance truck drivers stationed, Brazil

    Directory of Open Access Journals (Sweden)

    Luciana Villarinho

    2002-08-01

    interviewed. Face-to-face interviews were carried out using open and closed questions covered demographic characteristics, sexual practices, drug use, knowledge of HIV and AIDS, previous contact with HIV prevention programs, and perception of their vulnerability to HIV and Aids. A descriptive analysis was carried out and reports are presented to illustrate some scenarios of vulnerability. RESULTS: Of all 279 truck drivers interviewed, 93% had a stable female partner, 40% engaged in casual sexual with female partners, and 19% said to have sex with other regular partners. Vulnerability to HIV is increased by inconsistent condom use in all categories of sexual partners. Long periods away from home seem not to be the only factor for their vulnerability to HIV as seen in studies on long distance truck drivers. CONCLUSIONS: The macho culture and traditional male behaviors are prominently seen among truck drivers. There is a need of investing more on prevention in this professional group. Prevention programs at the work environment seem to be a promising strategy, since it allows a better understanding of the workers' setting and development of customized educational interventions.

  7. Scenario analysis of hybrid class 3-7 heavy vehicles.

    Energy Technology Data Exchange (ETDEWEB)

    An, F.; Stodolsky, F.; Vyas, A.; Cuenca, R.; Eberhardt, J. J.

    1999-12-23

    The effects of hybridization on heavy-duty vehicles are not well understood. Heavy vehicles represent a broader range of applications than light-duty vehicles, resulting in a wide variety of chassis and engine combinations, as well as diverse driving conditions. Thus, the strategies, incremental costs, and energy/emission benefits associated with hybridizing heavy vehicles could differ significantly from those for passenger cars. Using a modal energy and emissions model, they quantify the potential energy savings of hybridizing commercial Class 3-7 heavy vehicles, analyze hybrid configuration scenarios, and estimate the associated investment cost and payback time. From the analysis, they conclude that (1) hybridization can significantly reduce energy consumption of Class 3-7 heavy vehicles under urban driving conditions; (2) the grid-independent, conventional vehicle (CV)-like hybrid is more cost-effective than the grid-dependent, electric vehicle (EV)-like hybrid, and the parallel configuration is more cost-effective than the series configuration; (3) for CV-like hybridization, the on-board engine can be significantly downsized, with a gasoline or diesel engine used for SUVs perhaps being a good candidate for an on-board engine; (4) over the long term, the incremental cost of a CV-like, parallel-configured Class 3-4 hybrid heavy vehicle is about %5,800 in the year 2005 and $3,000 in 2020, while for a Class 6-7 truck, it is about $7,100 in 2005 and $3,300 in 2020; and (5) investment payback time, which depends on the specific type and application of the vehicle, averages about 6 years under urban driving conditions in 2005 and 2--3 years in 2020.

  8. Nuclear power prospects and potential: scenarios

    International Nuclear Information System (INIS)

    Rogner, Hans-Hogler; McDonald, Alan; )

    2002-01-01

    This paper outlines a range of scenarios describing what the world's energy system might look in the middle of the century, and what nuclear energy's most profitable role might be. The starting point is the 40 non-greenhouse-gas-mitigation scenarios in the Special Report on Emission Scenarios (SRES) of the Intergovernmental Panel on Climate Change (IPCC). Given their international authorship and comprehensive review by governments and scientific experts, the SRES scenarios are the state of the art in long-term energy scenarios

  9. Emissions from nine heavy trucks fueled by diesel and biodiesel blend without engine modification

    International Nuclear Information System (INIS)

    Wang, W.G.; Lyons, D.W.; Clark, N.N.; Gautam, M.; Norton, P.M.

    2000-01-01

    Biodiesel, a fuel that can be made from renewable biological sources such as vegetable oils or animal fats, has been recognized recently as an environment friendly alternative fuel for diesel engines. In this paper, the authors describe a study that compared exhaust emissions from in-use heavy trucks fueled with a biodiesel blend with those from trucks fueled with petroleum diesel. The biodiesel blend tested is a mixture of 35% biodiesel and 65% petroleum diesel, a blend designated as B35. The study is based on the field test results from West Virginia University's Transportable Heavy Duty Chassis Dynamometer Emissions Testing Laboratory and sponsored by the US Department of Energy. The heavy trucks the authors tested performed well when the originally equipped compression-ignition engine (diesel engine) was fueled with B35 without any engine modifications. Fuel economy (in terms of gallon per mile) of the two fuels was about the same. The emissions test results have shown that the heavy trucks fueled by B35 emitted significantly lower particulate matter (PM) and moderately lower carbon monoxide (CO) and hydrocarbon (HC) than the same trucks fueled by no. 2 diesel (D2). Oxides of nitrogen (NO x ) emissions from B35 and D2, however, were generally in the same level. Emissions variations from two different engine models and two driving cycles were also observed. Although the authors recommend more tests for biodiesel vehicles, the data obtained in this study indicate that biodiesel has promise as an emissions-reducing alternative fuel for diesel engines

  10. Driving fatigue in professional drivers: a survey of truck and taxi drivers.

    Science.gov (United States)

    Meng, Fanxing; Li, Shuling; Cao, Lingzhi; Li, Musen; Peng, Qijia; Wang, Chunhui; Zhang, Wei

    2015-01-01

    Fatigue among truck drivers has been studied extensively; however, less is known regarding the fatigue experience of taxi drivers in heavily populated metropolitan areas. This study aimed to compare the differences and similarities between truck and taxi driver fatigue to provide implications for the fatigue management and education of professional drivers. A sample of 274 truck drivers and 286 taxi drivers in Beijing was surveyed via a questionnaire, which included items regarding work characteristics, fatigue experience, accident information, attitude toward fatigue, and methods of counteracting fatigue. Driver fatigue was prevalent among professional drivers, and it was even more serious for taxi drivers. Taxi drivers reported more frequent fatigue experiences and were involved in more accidents. Among the contributing factors to fatigue, prolonged driving time was the most important factor identified by both driver groups. Importantly, the reason for the engagement in prolonged driving was neither due to the lack of awareness concerning the serious outcome of fatigue driving nor because of their poor detection of fatigue. The most probable reason was the optimism bias, as a result of which these professional drivers thought that fatigue was more serious for other drivers than for themselves, and they thought that they were effective in counteracting the effect of fatigue on their driving performance. Moreover, truck drivers tended to employ methods that require stopping to counteract fatigue, whereas taxi drivers preferred methods that were simultaneous with driving. Although both driver groups considered taking a nap as one of the most effective means to address fatigue, this method was not commonly used. Interestingly, these drivers were aware that the methods they frequently used were not the most effective means to counteract fatigue. This study provides knowledge on truck and taxi drivers' characteristics in fatigue experience, fatigue attitude, and

  11. Real world efficiency of retrofit partial-flow diesel particulate filters for trucks

    Energy Technology Data Exchange (ETDEWEB)

    Van Asch, R.; Verbeek, R.; Ligterink, N.; Kadijk, G.

    2009-11-15

    In 2006 the Dutch Ministry of Housing, Spatial Planning and the Environment (VROM) introduced an incentive scheme for retrofitting diesel particulate filters on Euro II and Euro III trucks. This scheme involves both partial flow and full flow diesel particulate filters (also called semi-open or open respectively wall-flow or closed filters). In the period 2007 till January 2009 about 15,000 partial flow filters and 8,000 full flow diesel particulate filters were installed. The minimum filtration efficiency requirement for the partial flow diesel particulate filters is 50% during the type approval test. In 2008 an engine dynamometer test programme was conducted to measure the filtration efficiency of retrofit open particulates filters of heavy trucks. This led to somewhat disappointing results with average filtration efficiencies in the range of 5-20% during city and national motorway driving conditions up to 20-40% during long distance motorway driving. This result leads to two main questions: (1) Is this result also representative for medium heavy trucks used for delivery, and (2) do similar efficiencies show up also in tests on entire vehicles, tested under conditions as close as possible to their real world usage profile. To this end, an additional measurement programme was defined, which is reported here. The objective of the study reported here is to determine the real world filtration efficiency of retrofit partial flow particulate filters for a number of trucks under different driving conditions such as city and motorway driving. The emphasis should be on medium heavy trucks typically used for national delivery.

  12. CAFE compliance by light trucks: economic impacts of clean diesel engine

    International Nuclear Information System (INIS)

    Teotia, A.; Vyas, A.; Cuenca, R.; Stodolsky, F.

    1999-01-01

    With the popularity of light trucks increasing in the United States, their share of the US light vehicle market had doubled between 1980 and 1996, climbing from 20 to 40%. By 1996, annual energy consumption for light trucks had risen to 5.97 x 10 15 Btu [5.97 quadrillion Btu, or ''quad'', or 6.30 x 10 18 joule (J)], compared to 7.94 quad (8.38 x 10 18 J) for cars. In recent years (since 1995), the fuel economy of US-manufactured light trucks (almost 99% of which use gasoline engines) has been below the Corporate Average Fuel Economy (CAFE) standards. This paper analyzes a strategy to reduce the CAFE shortfalls by adopting the new, highly energy-efficient clean diesel engine. Research on such engines has been funded by the US Department of Energy, Office of Heavy Vehicle Technologies, under its Light Truck Clean Diesel Engine Program. A clean diesel engine market penetration trajectory is developed, representing an industry response to meet the CAFE standards. Whether the engine will be produced inside the country or imported remains uncertain, so two cases are defined. Values of exports/imports of clean diesel engines/trucks under these cases are estimated. The macroeconomic benefits are estimated by using a model of the US economy developed by Standard and Poor's Data Resources, Inc. On the basis of gains in the gross domestic product projected under the alternative cases, domestic production of the clean diesel engine is favored over importing it. (author)

  13. Towards a user's guide to scenarios - a report on scenario types and scenario techniques

    Energy Technology Data Exchange (ETDEWEB)

    Boerjeson, Lena; Hoejer, Mattias; Dreborg, Karl-Henrik; Finnveden, Goeran [Royal Inst. of Technology, Stockholm (Sweden). Environmental Strategies Research - fms; Ekvall, Tomas [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Energy and Environment

    2005-11-01

    Futures studies consist of a vast variation of studies and approaches. The aim of this paper is to contribute to the understanding of for what purposes scenarios are useful and what methods and procedures are useful for furthering these purposes. We present a scenario typology with an aim to better suit the context in which the scenarios are used. The scenario typology is combined with a new way of looking at scenario techniques, i.e. practical methods and procedures for scenario development. Finally, we look at the usefulness of scenarios in the light of the scenario typology and the scenario techniques. As a start, we distinguish between three main categories of scenario studies. The classification is based on the principal questions we believe a user may want to pose about the future. The resolution is then increased by letting each category contain two different scenario types. These are distinguished by different angles of approach of the questions defining the categories. The first question, What will happen?, is responded to by Predictive scenarios. In fact, the response to a question like this will always be conditional, e.g. of a stable and peaceful world, or by a certain continuous development of some kind. We have utilized this fact when defining the two predictive scenario types, Forecasts and What-if scenarios. The second question, What can happen?, is responded to by Explorative scenarios. The scenarios are thus explorations of what might happen in the future, regardless of beliefs of what is likely to happen or opinions of what is desirable. This category is further divided into external and strategic scenarios. The final question, How can a specific target be reached?, is responded to by Normative scenarios. Such studies are explicitly normative, since they take a target as a starting point. They are often directed towards how the target could be reached. This category is divided into preserving and transforming scenarios. If the user wants to

  14. Effect of Uphill Flexible Pavements on The Damaging Effect Of Full-Trailer Trucks With Tandem Front Axles

    Directory of Open Access Journals (Sweden)

    Sabah Said Razouki

    2017-08-01

    Full Text Available The effect of traffic on flexible pavements can be expressed in terms of truck equivalence factors. This paper presents a study on the effect of uphill pavements on the damaging effect (truck equivalence factors of two types of full-trailer trucks with tandem front axles. Axle load and geometrical characteristics survey on the two types of full-trailer trucks were carried out for determining the data needed in this study. In addition, uphill slope survey in Kerbala city was done and the data of uphill slope of other Iraqi cities were obtained from previous surveys. The paper reveals that the uphill pavement gradient causes significant increase in truck equivalence factors. In addition, the research reveals that there are many factors affecting the truck equivalence factors on uphill flexible pavements, including the total weight of full-trailer, H/B ratio (height of center of gravity to the wheel base of the truck, magnitude of uphill slope, and the structural number (SN.This work shows the importance of considering the effect of uphill slope in the design of flexible pavements on steep uphill slopes.

  15. Trends in truck freight energy use and carbon emissions in selected OECD countries from 1973 to 2005

    International Nuclear Information System (INIS)

    Kamakate, Fatumata; Schipper, Lee

    2009-01-01

    Trends in truck freight energy use and carbon emissions: In the age of global supply chains and 'just in time' logistics, fast and efficient goods movement is often seen as an economic imperative. Growth in global goods movement not only translates into growth in commercial trucking activity but also into growth in the share of trucking compared to other modes of in-country freight transportation. These trends have a significant impact on the energy intensity of freight transport. Using a bottom-up approach relying on national data, this study compares the energy intensity of truck freight in Australia, France, Japan, the United Kingdom and the United States from 1973 to the present. The analysis builds on previous work by and decomposing energy use for freight. Intensity is expressed in terms of vehicle intensity (megajoules/vehicle-kilometer), modal energy intensity (megajoules/tonne-kilometer), and carbon intensity (grams/tonne-km). The cross-country comparison highlights in part the influence of geography, transportation infrastructure, and truck utilization patterns on energy and carbon intensity from this sector. While improving fuel economy of individual vehicles is very important, large reductions in trucking energy use and emissions will also come from better logistics and driving, higher load factors, and better matching of truck capacity to load.

  16. Classifying Scenarios in a Product Design Process: a study to achieve automated scenario generation

    NARCIS (Netherlands)

    Anggreeni, Irene; van der Voort, Mascha C.; van Houten, F.J.A.M.; Miedema, J.; Lutters, D.

    2008-01-01

    This paper explains the possible uses of scenarios in product design. A scenario classification is proposed as a framework to create, use and reuse different types of scenarios in a product design process. Our aims are three-fold: (1) to obtain a better view on the extent to which scenarios can be

  17. Can cars and trucks coexist peacefully on highways? Analyzing the effectiveness of road safety policies in Europe.

    Science.gov (United States)

    Castillo-Manzano, José I; Castro-Nuño, Mercedes; Fageda, Xavier

    2015-04-01

    We examine the impact on the traffic accident rate of the interaction between trucks and cars on Europe's roads using a panel data set that covers the period 1999-2010. We find that rising motorization rates for trucks lead to higher traffic fatalities, while rising motorization rates for cars do not. Empirically, the model we build predicts the positive impact of stricter speed limit legislation for trucks in the reduction of road fatalities. These findings lend support to European strategies and aimed at promoting alternative modes of freight transport, including rail and maritime transport. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. IPCC Special report on Emissions Scenarios (SRES)

    International Nuclear Information System (INIS)

    Anon

    2001-01-01

    This special report on emissions scenarios (SRES) is intended to reflect the most recent trends in driving forces of emissions; population projections economic development, and structural and technological change. It serves as an update to IS92 scenarios developed by IPCC in the early 1990s to illustrate a plausible range of future greenhouse gas emissions. This update is based on a review of the literature and the development of a database of over 400 global and regional scenarios; 190 of these extend from 1900 to 2100 and thus fed into the development of the narrative scenarios and storylines. Based on the literature review, a set of four alternative scenario families, having a total of 40 emission scenarios have been developed. Each scenario family includes a narrative storyline which describes a demographic, social. economic, technological, environmental and policy future. Characteristic features of each of the four families are summarized and a comparison is made between the IS92 and SRES. One of the main conclusions of this recent scenario construction effort is the realization that alternative combinations of main scenario driving forces can lead to similar levels of GHG emissions by the end of the 21st century, and that scenarios with different underlying assumptions can result in very similar climate change

  19. Project scenarios for bitumen upgrading

    International Nuclear Information System (INIS)

    Koppel, P.E.; Mazurek, W.L.; Harji, A.

    2002-01-01

    The established reserves of Alberta's heavy oil resources are 178 billion barrels, and potential recoverable reserves are 315 billion barrels. The challenge of production includes the logistics of recovery, upgrading and transportation to market. Utilization of the bitumen is not simple because bitumen is too viscous to transport by pipeline. In addition, it is not processable by most existing refineries unless it can be upgraded through dilution. This paper examined different factors regarding the economic viability of various upgrading methods of a wide range of bitumen feedstocks. The study also examined the sensitivity of refinery demand to the prices of these feedstocks, along with the competitiveness among bitumen-based feedstock and conventional crudes. Western Canada, Ontario and the PADD II district in the United States are the 3 major markets for western Canadian bitumen based feedstock, the demand for which depends on refinery configurations and asphalt demand. This paper described the following 4 generic scenarios that describe Alberta bitumen upgrading projects: (1) adjacent to open pit mines, (2) adjacent to steam assisted gravity drainage (SAGD) facilities, (3) remotely located from resource production at an existing refinery, and (4) pipeline bitumen. It was noted that producers should determine the best way to upgrade the bitumen to ensure there is an economic market for the product, but they should also be aware not to over process the bitumen so as not to leave existing refinery facilities under-utilized. 2 refs., 1 tab., 3 figs

  20. NIOSH national survey of long-haul truck drivers: Injury and safety

    Science.gov (United States)

    Chen, Guang X.; Sieber, W. Karl; Lincoln, Jennifer E.; Birdsey, Jan; Hitchcock, Edward M.; Nakata, Akinori; Robinson, Cynthia F.; Collins, James W.; Sweeney, Marie H.

    2015-01-01

    Approximately 1,701,500 people were employed as heavy and tractor-trailer truck drivers in the United States in 2012. The majority of them were long-haul truck drivers (LHTDs). There are limited data on occupational injury and safety in LHTDs, which prompted a targeted national survey. The National Institute of Occupational Safety and Health conducted a nationally representative survey of 1265 LHTDs at 32 truck stops across the contiguous United States in 2010. Data were collected on truck crashes, near misses, moving violations, work-related injuries, work environment, safety climate, driver training, job satisfaction, and driving behaviors. Results suggested that an estimated 2.6% of LHTDs reported a truck crash in 2010, 35% reported at least one crash while working as an LHTD, 24% reported at least one near miss in the previous 7 days, 17% reported at least one moving violation ticket and 4.7% reported a non-crash injury involving days away from work in the previous 12 months. The majority (68%) of non-crash injuries among company drivers were not reported to employers. An estimate of 73% of LHTDs (16% often and 58% sometimes) perceived their delivery schedules unrealistically tight; 24% often continued driving despite fatigue, bad weather, or heavy traffic because they needed to deliver or pick up a load at a given time; 4.5% often drove 10 miles per hours or more over the speed limit; 6.0% never wore a seatbelt; 36% were often frustrated by other drivers on the road; 35% often had to wait for access to a loading dock; 37% reported being noncompliant with hours-of-service rules (10% often and 27% sometimes); 38% of LHTDs perceived their entry-level training inadequate; and 15% did not feel that safety of workers was a high priority with their management. This survey brings to light a number of important safety issues for further research and interventions, e.g., high prevalence of truck crashes, injury underreporting, unrealistically tight delivery schedules

  1. Scenario research: The food industry in 2010

    DEFF Research Database (Denmark)

    Stacey, Julia; Sonne, Anne-Mette; Jensen, Birger Boutrup

    2001-01-01

    at MAPP and the Department of Manufacturing Engineering and Management, The Technical University of Denmark have constructed three scenarios about the Danish food industry in 2010. The aim has been to identify the demands the food industry can expect to meet in the future plus which research areas...... the public research should prioritise in order to support the development of competences within the food industry. The scenarios are isolated developments. In practise, the future is likely to be a combination of the different tendencies within the scenarios. The first scenario 'Naturalness' has focus...... by practicians in relation to the scenarios. The scenario 'Naturalness' requires a change of attitude among food producers and society in general. A big challenge for the Danish food industry is that they must accept that its primary role will change from being an important exporting industry to an industry...

  2. Numerically investigating the emergent cyclic inflation scenario

    International Nuclear Information System (INIS)

    Duhe, William; Biswas, Tirthabir

    2014-01-01

    We provide a comprehensive numerical study of the emergent cyclic inflation scenario. This is a scenario where instead of traditional monotonic slow roll inflation, the universe expands over numerous short asymmetric cycles due to the production of entropy via interactions among different species. This is one of the very few scenarios of inflation that provides a non-singular geodesically complete space-time and does not require any ‘reheating’ mechanism. (paper)

  3. Analysis of the energy scenario Negawatt 2006

    International Nuclear Information System (INIS)

    Acket, C.; Bacher, P.

    2006-10-01

    The association Negawatt published in 2003 an energy scenario for the France in 2050, under the name of Negawatt 2006. This document aims to analyze the scenario Negawatt with a comparison of the scenario published on the web site of SLC, Save the Climate. The authors analyzes the main three sectors: electricity, transports and residential to propose their comparison in conclusion. (A.L.B.)

  4. Scenario research: Can the future be predicted?

    DEFF Research Database (Denmark)

    Stacey, Julia; Sonne, Anne-Mette

    2000-01-01

    possible futures. In the process of creating the scenarios, researchers at MAPP and the Danish Technical University formulated mini scenarios based on their research. The scenarios were used as inspiration in discussions with experts from industry, trade organisations, authorities etc. and later discussed...... and supplemented at workshops - one for each of the four sectors. Experts from industry, trade organisations, retailing, authorities and other interested parties participated....

  5. MIOSAT Mission Scenario and Design

    Science.gov (United States)

    Agostara, C.; Dionisio, C.; Sgroi, G.; di Salvo, A.

    2008-08-01

    MIOSAT ("Mssione Ottica su microSATellite") is a low-cost technological / scientific microsatellite mission for Earth Observation, funded by Italian Space Agency (ASI) and managed by a Group Agreement between Rheinmetall Italia - B.U. Spazio - Contraves as leader and Carlo Gavazzi Space as satellite manufacturer. Several others Italians Companies, SME and Universities are involved in the development team with crucial roles. MIOSAT is a microsatellite weighting around 120 kg and placed in a 525 km altitude sun-synchronuos circular LEO orbit. The microsatellite embarks three innovative optical payloads: Sagnac multi spectral radiometer (IFAC-CNR), Mach Zehender spectrometer (IMM-CNR), high resolution pancromatic camera (Selex Galileo). In addition three technological experiments will be tested in-flight. The first one is an heat pipe based on Marangoni effect with high efficiency. The second is a high accuracy Sun Sensor using COTS components and the last is a GNSS SW receiver that utilizes a Leon2 processor. Finally a new generation of 28% efficiency solar cells will be adopted for the power generation. The platform is highly agile and can tilt along and cross flight direction. The pointing accuracy is in the order of 0,1° for each axe. The pointing determination during images acquisition is <0,02° for the axis normal to the boresight and 0,04° for the boresight. This paper deals with MIOSAT mission scenario and definition, highlighting trade-offs for mission implementation. MIOSAT mission design has been constrained from challenging requirements in terms of satellite mass, mission lifetime, instrument performance, that have implied the utilization of satellite agility capability to improve instruments performance in terms of S/N and resolution. The instruments provide complementary measurements that can be combined in effective ways to exploit new applications in the fields of atmosphere composition analysis, Earth emissions, antropic phenomena, etc. The Mission

  6. Medium Truck Duty Cycle Data from Real-World Driving Environments: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Lascurain, Mary Beth [ORNL; Franzese, Oscar [ORNL; Capps, Gary J [ORNL; Siekmann, Adam [ORNL; Thomas, Neil [ORNL; LaClair, Tim J [ORNL; Barker, Alan M [ORNL; Knee, Helmut E [ORNL

    2012-11-01

    Since the early part of the 20th century, the US trucking industry has provided a safe and economical means of moving commodities across the country. At present, nearly 80% of US domestic freight movement involves the use of trucks. The US Department of Energy (DOE) is spearheading a number of research efforts to improve heavy vehicle fuel efficiencies. This includes research in engine technologies (including hybrid and fuel cell technologies), lightweight materials, advanced fuels, and parasitic loss reductions. In addition, DOE is developing advanced tools and models to support heavy vehicle research and is leading the 21st Century Truck Partnership and the SuperTruck development effort. Both of these efforts have the common goal of decreasing the fuel consumption of heavy vehicles. In the case of SuperTruck, a goal of improving the overall freight efficiency of a combination tractor-trailer has been established. This Medium Truck Duty Cycle (MTDC) project is a critical element in DOE s vision for improved heavy vehicle energy efficiency; it is unique in that there is no other existing national database of characteristic duty cycles for medium trucks based on collecting data from Class 6 and 7 vehicles. It involves the collection of real-world data on medium trucks for various situational characteristics (e.g., rural/urban, freeway/arterial, congested/free-flowing, good/bad weather) and looks at the unique nature of medium trucks drive cycles (stop-and-go delivery, power takeoff, idle time, short-radius trips). This research provides a rich source of data that can contribute to the development of new tools for FE and modeling, provide DOE a sound basis upon which to make technology investment decisions, and provide a national archive of real-world-based medium-truck operational data to support energy efficiency research. The MTDC project involved a two-part field operational test (FOT). For the Part-1 FOT, three vehicles each from two vocations (urban transit and

  7. North American Free Trade Agreement: Coordinated Operational Plan Needed to Ensure Mexican Trucks' Compliance With U.S. Standards

    National Research Council Canada - National Science Library

    2001-01-01

    .... In February 2001, a NAFTA arbitration panel ruled that the United States blanket refusal to process applications by Mexican trucking companies to provide cross-border services beyond the commercial...

  8. Study of the impact of a telematics system on safe and fuel-efficient driving in trucks : [technology brief].

    Science.gov (United States)

    2014-04-01

    Transportation and logistics companies increasingly : rely on modern technologies and in-vehicle tools : (also known as telematics systems) to optimize their : truck fleet operations. Telematics is technology that : combines telecommunications (i.e.,...

  9. Developing corridor-level truck travel time estimates and other freight performance measures from archived ITS data.

    Science.gov (United States)

    2009-08-01

    The objectives of this research were to retrospectively study the feasibility for using truck transponder data to produce freight corridor performance measures (travel times) and real-time traveler information. To support this analysis, weigh-in-moti...

  10. Research notes : developing corridor-level truck travel time estimates and other freight performance measures from archived ITS data.

    Science.gov (United States)

    2010-02-01

    This research project demonstrated that it is feasible to use the WIM data to develop long-term corridor performance monitoring of truck travel. From the perspective of a realtime traveler information system, there are too many shortcomings mainl...

  11. The unfolding: scenario planning in nursing.

    Science.gov (United States)

    Woude, Diana Vander; Damgaard, Gloria; Hegge, Margaret J; Soholt, Deb; Bunkers, Sandra Schmidt

    2003-01-01

    An interdisciplinary consortium organized a group to explore the meaning and the future of nursing in South Dakota using scenario planning. This column provides a general description of the four scenarios that emerged, some observations about how they might evolve, comments on their implications, and first-person stories, as told by fictitious residents. The process of scenario planning is connected to nursing science by explicating how five lessons of scenario planning are linked with Parse's human becoming concepts of creative imagining, glimpsing the paradoxical, and affirming personal becoming.

  12. Using Service Scenarios to Model Business Services

    DEFF Research Database (Denmark)

    Bækgaard, Lars

    The purpose of the paper is to present and evaluate the notion of service scenarios. A service is work done by a service executor in interaction with a service consumer. A service scenario is a model of a service system and the roles that are played by the actors participating and interacting...... during the execution of a service. The model represents the roles and the interactions between the participants. Service scenarios can be used to model specific services and roles played by human beings and IT systems in the execution of services. The use of service scenarios is demonstrated by means...

  13. Visualizing Risks: Icons for Information Attack Scenarios

    National Research Council Canada - National Science Library

    Hosmer, Hilary

    2000-01-01

    .... Visual attack scenarios help defenders see system ambiguities, imprecision, vulnerabilities and omissions, thus speeding up risk analysis, requirements gathering, safeguard selection, cryptographic...

  14. Action research Toolkit II: The Scenario Workshop

    DEFF Research Database (Denmark)

    Rasmussen, Lauge Baungaard

    2003-01-01

    The article describes the scenario workshop within the action research paradigm. In addtion, the maina phases and the functions of the facilitator and the participants are outlined. Finally,it describes and analyses the experiences of using the scenario workshop in practice.......The article describes the scenario workshop within the action research paradigm. In addtion, the maina phases and the functions of the facilitator and the participants are outlined. Finally,it describes and analyses the experiences of using the scenario workshop in practice....

  15. Energy scenarios for Colombia: process and content

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Ricardo A. [National Univ. of Colombia, Escuela de Geosciencias y Medio Ambiente, Medellin (Colombia); Vesga, Daniel R.A. [Unidad de Planeacion Minero Energetica, Bogota (Colombia); Cadena, Angela I. [Los Andes Univ., School of Engineering, Bogota (Colombia); Boman, Ulf [Kairos Future AB, Stockholm (Sweden); Larsen, Erik [Cass Business School, London (United Kingdom); Dyner, Isaac [Universidad Nacional de Colombia, Energy Inst., Medellin (Colombia)

    2005-02-01

    This paper presents the approach undertaken, and the four energy scenarios that have been developed, to support long term energy policy in Colombia. The scenarios were constructed with emphasis on maximum interaction between stakeholders in the Colombian energy sector. The process directly involved over 120 people. The scenarios were developed as strategic support tools for the Energy and Mining Planning Unit (UPME), which is the Colombian institution in charge of developing the country's energy strategies and National Energy Policy. The methodology employed is presented, followed by a detailed description of each of the four scenarios. (Author)

  16. Role of sensory and cognitive conspicuity in the prevention of collisions between motorcycles and trucks at T-intersections.

    Science.gov (United States)

    Law, Teik Hua; Ghanbari, Mahshid; Hamid, Hussain; Abdul-Halin, Alfian; Ng, Choy Peng

    2016-11-01

    Motorcyclists are particularly vulnerable to injury in crashes with heavy vehicles due to substantial differences in vehicle mass, the degree of protection and speed. There is a considerable difference in height between motorcycles and trucks; motorcycles are viewed by truck drivers from downward angles, and shorter distances between them mean steeper downward angles. Hence, we anticipated that the effects of motorcycle conspicuity treatments would be different for truck drivers. Therefore, this study aims to evaluate the effects of motorcycle conspicuity treatments on the identification and detection of motorcycles by truck drivers. Two complementary experiments were performed; the first experiment assessed the impact of motorcycle sensory conspicuity on the ability of un-alerted truck drivers to detect motorcycles, and the second experiment assessed the motorcycle cognitive conspicuity to alerted truck drivers. The sensory conspicuity was measured in terms of motorcycle detection rates by un-alerted truck drivers when they were not anticipating a motorcycle within a realistic driving scene, while the cognitive conspicuity was determined by the time taken by alerted truck drivers to actively search for a motorcycle. In the first experiment, the participants were presented with 10 pictures and were instructed to report the kinds of vehicles that were presented in the pictures. Each picture was shown to the participants for 600ms. In the second experiment, the participants were presented with the same set of pictures and were instructed to respond by clicking the right button on a mouse as soon as they detected a motorcycle in the picture. The results indicate that the motorcycle detection rate increases, and the response time to search for a motorcycle decreases, as the distance between the targeted motorcycle and the viewer decreases. This is true regardless of the type of conspicuity treatment used. The use of daytime running headlights (DRH) was found to

  17. In-use activity, fuel use, and emissions of heavy-duty diesel roll-off refuse trucks.

    Science.gov (United States)

    Sandhu, Gurdas S; Frey, H Christopher; Bartelt-Hunt, Shannon; Jones, Elizabeth

    2015-03-01

    The objectives of this study were to quantify real-world activity, fuel use, and emissions for heavy duty diesel roll-off refuse trucks; evaluate the contribution of duty cycles and emissions controls to variability in cycle average fuel use and emission rates; quantify the effect of vehicle weight on fuel use and emission rates; and compare empirical cycle average emission rates with the U.S. Environmental Protection Agency's MOVES emission factor model predictions. Measurements were made at 1 Hz on six trucks of model years 2005 to 2012, using onboard systems. The trucks traveled 870 miles, had an average speed of 16 mph, and collected 165 tons of trash. The average fuel economy was 4.4 mpg, which is approximately twice previously reported values for residential trash collection trucks. On average, 50% of time is spent idling and about 58% of emissions occur in urban areas. Newer trucks with selective catalytic reduction and diesel particulate filter had NOx and PM cycle average emission rates that were 80% lower and 95% lower, respectively, compared to older trucks without. On average, the combined can and trash weight was about 55% of chassis weight. The marginal effect of vehicle weight on fuel use and emissions is highest at low loads and decreases as load increases. Among 36 cycle average rates (6 trucks×6 cycles), MOVES-predicted values and estimates based on real-world data have similar relative trends. MOVES-predicted CO2 emissions are similar to those of the real world, while NOx and PM emissions are, on average, 43% lower and 300% higher, respectively. The real-world data presented here can be used to estimate benefits of replacing old trucks with new trucks. Further, the data can be used to improve emission inventories and model predictions. In-use measurements of the real-world activity, fuel use, and emissions of heavy-duty diesel roll-off refuse trucks can be used to improve the accuracy of predictive models, such as MOVES, and emissions

  18. PENGARUH CITRA MEREK TERHADAP PENGAMBILAN KEPUTUSAN PEMBELIAN MOBIL HINO JENIS DUMP TRUCK PADA PT. KUMALA MOTOR SEJAHTERA MAKASSAR

    OpenAIRE

    -, S U P A R J O

    2014-01-01

    2014 vii ABSTRAK PENGARUH CITRA MEREK TERHADAP PENGAMBILAN KEPUTUSAN PEMBELIAN MOBIL HINO JENIS DUMP TRUCK PADA PT. KUMALA MOTOR SEJAHTERA MAKASSAR Affect of Brand Image toward Taking of Decision in Purchase of Hino kind of Dump Truck on Kumala Motor Sejahtera Ltd., Makassar Suparjo Hj. Nurjannah Hamid Fahrina Mustafa Tujuan penelitian ini adalah : (i) untuk menganalisis pengaruh citra merek meliputi kualitas merek, loyalitas merek dan asosiasi merek terhadap kep...

  19. New lead acid batteries for heavy duty trucks - more robust and maintenance free; Neue, robustere und wartungsfreie Bleibatterien fuer Nutzfahrzeuge

    Energy Technology Data Exchange (ETDEWEB)

    Geiger, Michael; Sarrau, Jean-Francois [Exide Technologies SAS, Gennevilliers (France)

    2011-08-15

    Today's truck industry is moving inevitably towards cleaner emission standards and limits. That way new requirements followed. For example: High vibration resistent batteries. The reason is, that the Adblue tank is now integrated in the former space of the starter battery, which has to be positioned in rough environment at the back of a truck. Therefore Exide developed special lead acid batteries with a high vibration standard. (orig.)

  20. Optimization of a truck-drone in tandem delivery network using k-means and genetic algorithm

    Directory of Open Access Journals (Sweden)

    Sergio Mourelo Ferrandez

    2016-04-01

    Full Text Available Purpose: The purpose of this paper is to investigate the effectiveness of implementing unmanned aerial delivery vehicles in delivery networks. We investigate the notion of the reduced overall delivery time, energy, and costs for a truck-drone network by comparing the in-tandem system with a stand-alone delivery effort. The objectives are (1 to investigate the time, energy, and costs associated to a truck-drone delivery network compared to standalone truck or drone, (2 to propose an optimization algorithm that determines the optimal number of launch sites and locations given delivery requirements, and drones per truck, (3 to develop mathematical formulations for closed form estimations for the optimal number of launch locations, optimal total time, as well as the associated cost for the system. Design/methodology/approach: The design of the algorithm herein computes the minimal time of delivery utilizing K-means clustering to find launch locations, as well as a genetic algorithm to solve the truck route as a traveling salesmen problem (TSP. The optimal solution is determined by finding the minimum cost associated to the parabolic convex cost function. The optimal min-cost is determined by finding the most efficient launch locations using K-means algorithms to determine launch locations and a genetic algorithm to determine truck route between those launch locations.  Findings: Results show improvements with in-tandem delivery efforts as opposed to standalone systems. Further, multiple drones per truck are more optimal and contribute to savings in both energy and time. For this, we sampled various initialization variables to derive closed form mathematical solutions for the problem. Originality/value: Ultimately, this provides the necessary analysis of an integrated truck-drone delivery system which could be implemented by a company in order to maximize deliveries while minimizing time and energy. Closed-form mathematical solutions can be used as