WorldWideScience

Sample records for led-based lighting system

  1. Development of white LED based PV lighting systems

    Energy Technology Data Exchange (ETDEWEB)

    Sastry, O.S.; Pant, P.C.; Prasad, G.; Kumar, Rajesh; Bandyopadhyay, Bibek [Solar Energy Centre, Ministry of New and Renewable Energy, Block 14, CGO Complex, Lodhi Road, New Delhi 110003 (India); Kamala Devi, V. [Agency for Non-Conventional Energy and Rural Technology, P.B. No. 1094, Pattom, P.O. Kasavadasapuram, Trivandrum, Kerala 695 004 (India)

    2010-09-15

    A high performance white light emitting diode (WLED) based PV lighting system has been developed under a joint project of SEC and ANERT. The system has been analyzed using the test set-ups developed as a part of advanced lighting laboratory (ALL). The results show that the performance is one of the best among the systems developed in the capacity range. (author)

  2. Optical design and lighting application of an LED-based sports lighting system

    Science.gov (United States)

    Boxler, Larry

    2011-10-01

    This paper describes both the optical development of an LED-based sports lighting system and the results of the application of the system to an actual sport field. A traditional sport lighting fixture is generally composed of a single 1500 watt High Intensity Discharge (HID) light source with reflectors used to control the light distribution. The efficacy of the HID light source is equivalent or nearly equivalent to most LED light sources, putting LEDs at a large cost disadvantage in a high light output application such as sports lighting due to the number of LEDs and supporting components required to run an LED system. To assess the feasibility and applicability of LEDs in a sports lighting application, an LED-based sport light has been developed and installed on a small soccer field specified to have an average maintained illuminance level of 30 footcandles. An existing HID sport lighting system was also installed on the same size soccer field adjacent to the LED field with the same average footcandle level for comparison. Results indicate that LEDs can provide equivalent average illumination; however the LED source and system component cost is substantially higher. Despite the high cost, it was found that improved optical control afforded by the optical design used in the system provides a significant improvement in offsite wasted spill light, glare control, and on field uniformity. This could provide an advantage for LED systems.

  3. Goniometric characterization of LED based greenhouse lighting

    DEFF Research Database (Denmark)

    Thorseth, Anders; Lindén, Johannes; Corell, Dennis Dan

    2015-01-01

    This paper describes a demonstration of goniospectroradiometry for characterizations of new light emitting diode (LED) based luminaries for enhanced photosynthesis in greenhouses. It highlights the differences between measurement of the traditional high pressure sodium (HPS) luminaries and the LED...

  4. LED based powerful nanosecond light sources for calibration systems of deep underwater neutrino telescopes

    Energy Technology Data Exchange (ETDEWEB)

    Lubsandorzhiev, B.K. [Institute for Nuclear Research of the Russian Academy of Sciences (Russian Federation); Kepler Center for Astro and Particle Physics, University of Tuebingen (Germany)], E-mail: lubsand@pcbai10.inr.ruhep.ru; Poleshuk, R.V.; Shaibonov, B.A.J.; Vyatchin, Y.E. [Institute for Nuclear Research of the Russian Academy of Sciences (Russian Federation)

    2009-04-11

    Powerful nanosecond light sources based on LEDs have been developed for use in calibration systems of deep underwater neutrino telescopes. The light sources use either matrixes of ultra bright blue InGaN LEDs or new generation high power blue LEDs. It is shown that such light sources have light yield of up to 10{sup 10}-10{sup 12} photons per pulse with very fast light emission kinetics. The developed light sources are currently used in a number of astroparticle physics experiments, namely: the lake Baikal neutrino experiment, the TUNKA EAS experiment, etc.

  5. LED-Based Colour Sensing System

    Directory of Open Access Journals (Sweden)

    Ibrahim AL-BAHADLY

    2010-03-01

    Full Text Available This paper presents a new colour sensing system for measuring the colour of car paint accurately enough to reproduce the paint proportions to cover up scratches or wear on a car. The aim is to repaint a car’s damaged area at a fraction of the cost of repainting the whole car. The proposed colour sensing system is based on Light Emitting Diode (LED. A prototype for the system has been designed, built, and tested. During this work light was researched as well as lighting sources, how light travels, how light reflects and refracts, ways light can be quantized, the human eye, why cameras look accurate, lighting conditions and their effects, and the emergence of colour.

  6. System Reliability for LED-Based Products

    Energy Technology Data Exchange (ETDEWEB)

    Davis, J Lynn; Mills, Karmann; Lamvik, Michael; Yaga, Robert; Shepherd, Sarah D; Bittle, James; Baldasaro, Nick; Solano, Eric; Bobashev, Georgiy; Johnson, Cortina; Evans, Amy

    2014-04-07

    Results from accelerated life tests (ALT) on mass-produced commercially available 6” downlights are reported along with results from commercial LEDs. The luminaires capture many of the design features found in modern luminaires. In general, a systems perspective is required to understand the reliability of these devices since LED failure is rare. In contrast, components such as drivers, lenses, and reflector are more likely to impact luminaire reliability than LEDs.

  7. LED-Based High-Voltage Lines Warning System

    Directory of Open Access Journals (Sweden)

    Eldar MUSA

    2013-04-01

    Full Text Available LED-based system, running with the current of high-voltage lines and converting the current flowing through the line into the light by using a toroid transformer, has been developed. The transformer’s primary winding is constituted by the high voltage power line. Toroidal core consists of two equal parts and the secondary windings are evenly placed on these two parts. The system is mounted on the high-voltage lines as a clamp. The secondary winding ends are connected in series by the connector on the clamp. LEDs are supplied by the voltage at the ends of secondary. Current flowing through highvoltage transmission lines is converted to voltage by the toroidal transformer and the light emitting LEDs are supplied with this voltage. The theory of the conversion of the current flowing through the line into the light is given. The system, running with the current of the line and converting the current into the light, has been developed. System has many application areas such as warning high voltage lines (warning winches to not hinder the high-voltage lines when working under the lines, warning planes to not touch the high-voltage lines, remote measurement of high-voltage line currents, and local illumination of the line area

  8. High Output LED-Based Profile Lighting Fixture

    DEFF Research Database (Denmark)

    Török, Lajos; Beczkowski, Szymon; Munk-Nielsen, Stig

    2011-01-01

    Recent developments in power light emitting diode (LED) industry have made LEDs suitable for being efficiently used in high intensity lighting fixtures instead of the commonly used high intensity discharge (HID) lamps. A high output LEDbased profile-light fixture is presented in this paper....... The system consists of a power supply with power factor correction (PFC), a LED-driver and an optical system designed for an overall high efficiency. An interleaved boost converter was chosen as PFC converter. A soft switching phase-shifted full-bridge converter with current doubler provides isolation from...... the grid and delivers the required voltage to the LEDdriver which is a dual interleaved buck converter. Twelve highpower CBT-90 LEDs have been connected in a 4xRGBconfiguration to deliver high output of saturated colors without the need for subtractive color filters. More than 6000 lm of fixture light...

  9. High Output LED-Based Profile Lighting Fixture

    DEFF Research Database (Denmark)

    Török, Lajos; Beczkowski, Szymon; Munk-Nielsen, Stig;

    2011-01-01

    . The system consists of a power supply with power factor correction (PFC), a LED-driver and an optical system designed for an overall high efficiency. An interleaved boost converter was chosen as PFC converter. A soft switching phase-shifted full-bridge converter with current doubler provides isolation from...... the grid and delivers the required voltage to the LEDdriver which is a dual interleaved buck converter. Twelve highpower CBT-90 LEDs have been connected in a 4xRGBconfiguration to deliver high output of saturated colors without the need for subtractive color filters. More than 6000 lm of fixture light...

  10. Integrated LED-based luminaire for general lighting

    Energy Technology Data Exchange (ETDEWEB)

    Dowling, Kevin J.; Lys, Ihor A.; Williamson, Ryan C.; Roberge, Brian; Roberts, Ron; Morgan, Frederick; Datta, Michael Jay; Mollnow, Tomas Jonathan

    2016-08-30

    Lighting apparatus and methods employing LED light sources are described. The LED light sources are integrated with other components in the form of a luminaire or other general purpose lighting structure. Some of the lighting structures are formed as Parabolic Aluminum Reflector (PAR) luminaires, allowing them to be inserted into conventional sockets. The lighting structures display beneficial operating characteristics, such as efficient operation, high thermal dissipation, high output, and good color mixing.

  11. Control and Driving Methods for LED Based Intelligent Light Sources

    DEFF Research Database (Denmark)

    Beczkowski, Szymon

    High power light-emitting diodes allow the creation of luminaires capable of generating saturated colour light at very high efficacies. Contrary to traditional light sources like incandescent and high-intensity discharge lamps, where colour is generated using filters, LEDs use additive light mixing......, where the intensity of each primary colour diode has to be adjusted to the needed intensity to generate specified colour. The function of LED driver is to supply the diode with power needed to achieve the desired intensity. Typically, the drivers operate as a current source and the intensity...... current. The model can also be used to create highly accurate luminaire model. Finally, a dual interleaved buck converter has been proposed for driving high power light-emitting diodes. Interleaving two converters lowers the output ripple current thus lowering the requirement on the output capacitor...

  12. Design of LED-based lighting system for medical endoscope%基于LED的医用内窥镜照明系统设计

    Institute of Scientific and Technical Information of China (English)

    周文光; 王春飞; 毛坤剑; 陈庆; 孔悦

    2015-01-01

    目的:设计一种基于发光二极管(light emitting diode,LED)的医用内窥镜照明系统,解决传统弧光灯发光效率低、温升高、使用寿命短等不足.方法:以带脉冲宽度调制(pule width modulation,PWM)功能的AD型单片机为核心进行控制,采用特制的RGB-LED混光合成白光的方法,通过光纤将合成后的光线传到内窥镜的前端对体内的组织器官进行照明.结果:将该照明系统通过光纤连接至内窥镜主机进行组织照明,光源显色指数高、效果好,可真实再现组织颜色.结论:该内窥镜照明系统发光效率高、功耗低、照明效果好,非常适用于内窥镜诊疗照明.

  13. High-output LED-based light engine for profile lighting fixtures with high color uniformity using freeform reflectors.

    Science.gov (United States)

    Gadegaard, Jesper; Jensen, Thøger Kari; Jørgensen, Dennis Thykjær; Kristensen, Peter Kjær; Søndergaard, Thomas; Pedersen, Thomas Garm; Pedersen, Kjeld

    2016-02-20

    In the stage lighting and entertainment market, light engines (LEs) for lighting fixtures are often based on high-intensity discharge (HID) bulbs. Switching to LED-based light engines gives possibilities for fast switching, additive color mixing, a longer lifetime, and potentially, more energy-efficient systems. The lumen output of a single LED is still not sufficient to replace an HID source in high-output profile fixtures, but combining multiple LEDs can create an LE with a similar output, but with added complexity. This paper presents the results of modeling and testing such a light engine. Custom ray-tracing software was used to design a high-output red, green and blue LED-based light engine with twelve CBT-90 LEDs using a dual-reflector principle. The simulated optical system efficiency was 0.626 with a perfect (R=1) reflector coating for light delivered on a target surface through the entire optical system. A profile lighting fixture prototype was created, and provided an output of 6744 lumen and an efficiency of 0.412. The lower efficiency was mainly due to a non-optimal reflector coating, and the optimized design is expected to reach a significantly higher efficiency.

  14. LED Based Optical Wireless Communication System for WBAN

    Directory of Open Access Journals (Sweden)

    ATTIYA BAQAI

    2016-10-01

    Full Text Available In this paper the O-WBANs (Optical Wireless Body Area Networks is presented as an alternative to the radio and microwave BANs which are plagued with issues like interference, power hungry, hazardous and costly spectrum. Various experiments performed in this work demonstrate the feasibility of LED (Light-Emitting Diode based optical systems to be used for BANs. The system cost is kept as low as possible. Mainly the effects on the optical link are observed under ambient light and with different modulation schemes by varying link distance and line of sight in this paper. Experimental results reveal the satisfactory link availability up to the distance of 7 feet (around 2m, the optimum range of WBAN and within the field of view of 30-60º. The low cost solution presented in this paper meets the WBANs data rate requirement for physiological data (i.e. 10-100 kbps. As IR (Infra-Red signals do not provide any interference with the signals generated by the medical equipment of hospitals which is the problem in case of RF or microwave signals, additionally the IR signals are confined within a room hence IR signaling can prove to be potential candidate for WBAN fulfilling its security and limited access requirement.

  15. Developing smart lighting LED-based device by using light parameterization and control method

    Science.gov (United States)

    Risteiu, Mircea; Ileana, Ioan; Marc, Gheorghe

    2016-12-01

    The paper presents a smart system for control of chromatic distribution of white light produced by LED sources in order to satisfy simultaneously physiological comfort and color rendering requests. In region of interest (ROI) lighted by an ensemble of RGB and white LED's, a system of appropriate light sensors (from UV to IR radiation) take the chromatic an intensity information and send them to a microcontroller based device. Following the actual state of illumination end the desired one, the microcontroller will command the LED drivers adequately to obtain the optimum situation.

  16. A review of RGB-LED based mixed-color illumination system for machine vision and microscopy

    Science.gov (United States)

    Hou, Lexin; Wang, Hexin; Xu, Min

    2016-09-01

    The theory and application of RGB-LED based mixed-color illumination system for use in machine vision and optical microscopy systems are presented. For machine vision system, relationship of various color sources and output image sharpness is discussed. From the viewpoint of gray scale images, evaluation and optimization methods of optimal illumination for machine vision are concluded. The image quality under monochromatic and mixed color illumination is compared. For optical microscopy system, demand of light source is introduced and design thoughts of RGB-LED based mixed-color illumination system are concluded. The problems need to be solved in this field are pointed out.

  17. DC Grids for Smart LED-Based Lighting: The EDISON Solution

    Directory of Open Access Journals (Sweden)

    Steffen Thielemans

    2017-09-01

    Full Text Available This paper highlights the benefits and possible drawbacks of a DC-based lighting infrastructure for powering Light Emitting Diode (LED-lamps. It also evaluates the efforts needed for integrating the so called smart lighting and other sensor/actuator based control systems, and compares existing and emerging solutions. It reviews and discusses published work in this field with special focus on the intelligent DC-based infrastructure named EDISON that is primarily dedicated to lighting, but is applicable to building automation in general. The EDISON “PowerLAN” consists of a DC-based infrastructure that offers telecommunication abilities and can be applied to lighting retrofitting scenarios for buildings. Its infrastructure allows simple and efficient powering of DC-oriented devices like LED lamps, sensors and microcontrollers, while offering a wired communication channel. This paper motivates the design choices for organizing DC lighting grids and their associated communication possibilities. It also shows how the EDISON based smart lighting solution is evolving today to include new communication technologies and to further integrate other parts of building management solutions through the OneM2M (Machine to Machine service bus.

  18. Psychophysical evaluations of various color rendering from LED-based architectural lighting

    Science.gov (United States)

    Thompson, Maria; O'Reilly, Una-May; Levin, Robert

    2007-09-01

    This paper reports a study on visual evaluation of colors under LED lighting operated by an energy-saving control strategy. Digitally controlled LED systems can produce various qualities of light, adjustable to users' requirements. In this context, a novel control concept inspired this research: strategic control of Red, Yellow, Green & Blue LEDs forming white light can further increase energy efficiency. The resulting (more efficient) light, however, would have decreased "color rendering" (ability of accurately reproduce colors). The notable point is that while reducing color rendering, color temperature and light levels can stay constant and hence the appearance of the modified light could stay the same, and only the colors of illuminated objects would change. But how spaces would be perceived under such light with changing color rendering is a key question. This research investigated the hypothesis that a significant range of color distortions would be unnoticeable under such dynamically controlled illumination, especially outside of users' main field of view. If successful, such control technique could be implemented for unoccupied spaces that would not tolerated dimming, and minimize peak hours energy waste, potentially enabling significant power reductions. Three incremental series of experiments were performed based on subjective assessment of colors under changing color rendering. Tests were carried out for central and peripheral vision, using laboratory booths (phase 1) and full scale architectural mockups (phase 2). Results confirmed the fundamental hypothesis, showing that the majority of subjects did not detect the color changes in their periphery while the same color changes were noticeable with direct observation.

  19. Modulation bandwidth enhancement of white-LED-based visible light communications using electrical equalizations

    Science.gov (United States)

    Kwon, D. H.; Yang, S. H.; Han, S. K.

    2015-01-01

    Utilizing the modulation capability of LEDs, there have been many studies about convergence technology to combine illumination and communication. The visible light communication (VLC) system has several advantages such as high security, immunity to RF interference and lower additional cost than comparing to LEDs just for illumination. However, modulation bandwidth of LEDs is not enough for various wireless communication systems. Since the commercial LEDs are designed only for lighting systems; we need an effort to enhance the modulation characteristics of LEDs. When the area of LED is increased, internal junction capacitance of LED is also increased depending on the area of LEDs and then the RC delay time of LED is increased. As a result, the modulation bandwidth of LEDs is limited by large RC delay time. In addition, frequency response of commercial white LED is degraded by the slow response time of the used yellow phosphor. Thus, modulation bandwidth of VLC system is limited to several MHz which is not enough to accommodate high data rate transmission. In this paper, we designed equalization circuit using RLC component for compensating the white LEDs frequency response. Also, we used blue filtering to improve frequency response of white LEDs, which is degraded by yellow phosphorescent component. Power loss by optical filtering and distance is compensated by convex lens. Consequently, we extend the modulation bandwidth of VLC system from 3 MHz to more than 180 MHz, and it allows NRZ-OOK data transmission up to 400 Mbps at 50 cm.

  20. Tri-band color transmission filter for white LED-based visible light communication

    Science.gov (United States)

    Wang, Qixia; Gu, Huarong; Tan, Qiaofeng

    2016-10-01

    Visible light communication (VLC) based on light emitting diodes has been regarded as an effective complement to radio frequency signal transmission. The color filter in VLC system plays the pivotal role for boosting signal-noise-ratio. In this paper, a tri-band color transmission filter with bandwidths consisting with LED's 30nm is designed based on guided mode resonance, incorporating a sub-wavelength aluminum grating on slab dielectric waveguide made of titanium dioxide on silica substrate. Parameters of grating structure, including the grating period, duty cycle, grating thickness, and waveguide thickness, are optimized by employing particle swarm optimization toolbox. The far field spectrum is calculated by rigorous coupled-wave analysis to verify the effectiveness of the designed filter. Three center-wavelength of transmission bands are 440nm, 530 and 630 nm. The full-width-at-half-maximum (FWHM) bandwidths of three bands are about 30nm which consist with LED's bandwidth.

  1. Testing a high-power LED based light source for hyperspectral imaging microscopy

    Science.gov (United States)

    Klomkaew, Phiwat; Mayes, Sam A.; Rich, Thomas C.; Leavesley, Silas J.

    2017-02-01

    Our lab has worked to develop high-speed hyperspectral imaging systems that scan the fluorescence excitation spectrum for biomedical imaging applications. Hyperspectral imaging can be used in remote sensing, medical imaging, reaction analysis, and other applications. Here, we describe the development of a hyperspectral imaging system that comprised an inverted Nikon Eclipse microscope, sCMOS camera, and a custom light source that utilized a series of high-power LEDs. LED selection was performed to achieve wavelengths of 350-590 nm. To reduce scattering, LEDs with low viewing angles were selected. LEDs were surface-mount soldered and powered by an RCD. We utilized 3D printed mounting brackets to assemble all circuit components. Spectraradiometric calibration was performed using a spectrometer (QE65000, Ocean Optics) and integrating sphere (FOIS-1, Ocean Optics). Optical output and LED driving current were measured over a range of illumination intensities. A normalization algorithm was used to calibrate and optimize the intensity of the light source. The highest illumination power was at 375 nm (3300 mW/cm2), while the lowest illumination power was at 515, 525, and 590 nm (5200 mW/cm2). Comparing the intensities supplied by each LED to the intensities measured at the microscope stage, we found there was a great loss in power output. Future work will focus on using two of the same LEDs to double the power and finding more LED and/or laser diodes and chips around the range. This custom hyperspectral imaging system could be used for the detection of cancer and the identification of biomolecules.

  2. Enhancement of light output power from LEDs based on monolayer colloidal crystal.

    Science.gov (United States)

    Geng, Chong; Wei, Tongbo; Wang, Xiaoqing; Shen, Dezhong; Hao, Zhibiao; Yan, Qingfeng

    2014-05-14

    One of the major challenges for the application of GaN-based light emitting diodes (LEDs) in solid-state lighting lies in the low light output power (LOP). Embedding nanostructures in LEDs has attracted considerable interest because they may improve the LOP of GaN-based LEDs efficiently. Recent advances in nanostructures derived from monolayer colloidal crystal (MCC) have made remarkable progress in enhancing the performance of GaN-based LEDs. In this review, the current state of the art in this field is highlighted with an emphasis on the fabrication of ordered nanostructures using large-area, high-quality MCCs and their demonstrated applications in enhancement of LOP from GaN-based LEDs. We describe the remarkable achievements that have improved the internal quantum efficiency, the light extraction efficiency, or both from LEDs by taking advantages of diverse functions that the nanostructures provided. Finally, a perspective on the future development of enhancement of LOP by using the nanostructures derived from MCC is presented. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Ambient Light An integrative, LED based interaction concept for different levels of automation

    OpenAIRE

    Dziennus, Marc; Kelsch, Johann; Schieben, Anna

    2016-01-01

    In the present paper an innovative approach for the driver-automation interaction based on visual signals is presented. A 360° LED stripe which is installed in the interior of the car communicates to the driver via his peripheral vision (Ambient light). A consistent, color-coded interaction design in the peripheral field of vision is used to guide the driver’s attention and to support him in different level of automation by providing automation-related information. The HMI concept uses situat...

  4. Laser Therapy and Dementia: A Database Analysis and Future Aspects on LED-Based Systems

    Directory of Open Access Journals (Sweden)

    Daniela Litscher

    2014-01-01

    Full Text Available Mainly because of the movement in the age pyramid, one can assume that the incidence of Alzheimer’s disease or dementia in general will increase in the coming decades. This paper employs a database analysis to examine the profile of publication activity related to this topic. Two databases were searched: PubMed and Cochrane Library. About 600 papers related to the research area “dementia and laser” and about 450 papers related to the search terms “Alzheimer and laser” were found in these two most commonly used databases. Ten plus one papers are described in detail and are discussed in the context of the laser research performed at the Medical University of Graz. First results concerning the measurement of the transmission factor (TF through the human skull of a new LED- (light emitting diode- based system are presented (TF = 0.0434 ± 0.0104 (SD. The measurements show that this LED system (using the QIT (quantum optical induced transparency effect might be used in the treatment of dementia.

  5. Specific LED-based red light photo-stimulation procedures improve overall sperm function and reproductive performance of boar ejaculates

    OpenAIRE

    2016-01-01

    The present study evaluated the effects of exposing liquid-stored boar semen to different red light LED regimens on sperm quality and reproductive performance. Of all of the tested photo-stimulation procedures, the best pattern consisted of 10 min light, 10 min rest and 10 min of further light (10-10-10 pattern). This pattern induced an intense and transient increase in the majority of motility parameters, without modifying sperm viability and acrosome integrity. While incubating non-photo-st...

  6. Specific LED-based red light photo-stimulation procedures improve overall sperm function and reproductive performance of boar ejaculates.

    Science.gov (United States)

    Yeste, Marc; Codony, Francesc; Estrada, Efrén; Lleonart, Miquel; Balasch, Sam; Peña, Alejandro; Bonet, Sergi; Rodríguez-Gil, Joan E

    2016-03-02

    The present study evaluated the effects of exposing liquid-stored boar semen to different red light LED regimens on sperm quality and reproductive performance. Of all of the tested photo-stimulation procedures, the best pattern consisted of 10 min light, 10 min rest and 10 min of further light (10-10-10 pattern). This pattern induced an intense and transient increase in the majority of motility parameters, without modifying sperm viability and acrosome integrity. While incubating non-photo-stimulated sperm at 37 °C for 90 min decreased all sperm quality parameters, this reduction was prevented when the previously-described light procedure was applied. This effect was concomitant with an increase in the percentage of sperm with high mitochondrial membrane potential. When sperm were subjected to 'in vitro' capacitation, photo-stimulation also increased the percentage of sperm with capacitation-like changes in membrane structure. On the other hand, treating commercial semen doses intended for artificial insemination with the 10-10-10 photo-stimulation pattern significantly increased farrowing rates and the number of both total and live-born piglets for parturition. Therefore, our results indicate that a precise photo-stimulation procedure is able to increase the fertilising ability of boar sperm via a mechanism that could be related to mitochondrial function.

  7. Assessing the Performance of LED-Based Flashlights Available in the Kenyan Off-Grid Lighting Market

    Energy Technology Data Exchange (ETDEWEB)

    Tracy, Jennifer; Jacobson, Arne; Mills, Evan

    2010-03-02

    Low cost rechargeable flashlights that use LED technology are increasingly available in African markets. While LED technology holds promise to provide affordable, high quality lighting services, the widespread dissemination of low quality products may make it difficult to realize this potential. This study includes performance results for three brands of commonly available LED flashlights that were purchased in Kenya in 2009. The performance of the flashlights was evaluated by testing five units for each of the three brands. The tests included measurements of battery capacity, time required to charge the battery, maximum illuminance at one meter, operation time and lux-hours from a fully charged battery, light distribution, and color rendering. All flashlights tested performed well below the manufacturers? rated specifications; the measured battery capacity was 30-50percent lower than the rated capacity and the time required to fully charge the battery was 6-25percent greater than the rated time requirement. Our analysis further shows that within each brand there is considerable variability in each performance indicator. The five samples within a single brand varied from each other by as much as 22percent for battery capacity measurements, 3.6percent for the number of hours required for a full charge, 23percent for maximum initial lux, 38percent for run time, 11percent for light distribution and by as much as 200percent for color rendering. Results obtained are useful for creating a framework for quality assurance of off-grid LED products and will be valuable for informing consumers, distributors and product manufacturers about product performance.

  8. Development and characterization of light-emitting diodes (LEDs) based on ruthenium complex single layer for transparent displays

    Energy Technology Data Exchange (ETDEWEB)

    Santos, G.; Fonseca, F.; Andrade, A.M. [Laboratorio de Microelectronica, Departamento de Engenharia de Sistemas Electronicos, Escola Politecnica da Universidade de Sao Paulo (Brazil); Patrocinio, A.O.T.; Mizoguchi, S.K.; Murakami Iha, N.Y. [Laboratorio de Fotoquimica Inorganica e Conversao de Energia, Instituto de Quimica da Universidade de Sao Paulo (Brazil); Peres, M.; Monteiro, T.; Pereira, L. [Departamento de Fisica e I3N, Universidade de Aveiro (Portugal)

    2008-08-15

    In this work, two ruthenium complexes,[Ru(bpy){sub 3}](PF{sub 6}){sub 2} and[Ru(ph2phen){sub 3}](PF{sub 6}){sub 2} in poly(methylmethacrylate) matrix were employed to build single-layer light-emitting electrochemical cells by spin coating on indium tin oxide substrate. In both cases the electroluminescence spectra exhibit a relatively broad band with maxima near to 625 nm and CIE (x,y) color coordinates of (0.64,0.36), which are comparable with the photoluminescence data in the same medium. The best result was obtained with the[Ru(bpy){sub 3}](PF{sub 6}){sub 2} device where the optical output power approaches 10{mu}W at the band maximum with a wall-plug efficiency higher than 0.03%. The lowest driving voltage is about 4 V for an electrical current of 20 mA. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  9. Light extraction efficiency enhancement of GaN-based blue LEDs based on ITO/ InxO ohmic contacts with microstructure formed by annealing in oxygen.

    Science.gov (United States)

    Luo, Yi; Bai, Yiming; Han, Yanjun; Li, Hongtao; Wang, Lai; Wang, Jian; Sun, Changzheng; Hao, Zhibiao; Xiong, Bing

    2016-05-16

    Indium tin oxide (ITO)/ indium oxide (InxO) double layer structure was adopted as the transparent conduction and light scattering function layer to improve the light extraction efficiency of the GaN-based blue LEDs. The double layer structure was first deposited in one run by electron beam evaporation using ITO and Indium as the source respectively, and then annealed in an oxygen environment. This method can fabricate transparent electrode with microstructure and low specific contact resistivity one time free from lithography and etching, which makes the fabrication process simple and at a ower cost. For the 220 nm ITO/ 170 nm InxO double layer sample annealed at 600°C for 15 min in oxygen, measurement results show that its root mean square of roughness of the surface microstructure can be as high as 85.2 nm which introduces the strongest light scattering. Its light transmittance at 450 nm can maintain 92.4%. At the same time, it can realize lower specific contact resistivity with p-InGaN. Compared with the GaN-based blue LEDs with only 220 nm ITO electrode, the light output power of the LEDs with 220 nm ITO/ 170 nm InxO double layer structure can be increased about 58.8%, and working voltage at 20 mA injection current is decreased about 0.23 V due to the enhanced current spreading capability. The light output power improvement is also theoretically convinced by finite difference time domain simulations.

  10. Novel Transparent Phosphor Conversion Matrix with High Thermal Conductivity for Next Generation Phosphor-Converted LED-based Solid State Lighting

    Energy Technology Data Exchange (ETDEWEB)

    Bockstaller, Michael [Carnegie Mellon Univ., Pittsburgh, PA (United States)

    2017-02-06

    The low thermal conductivity of state-of-the-art polymer encapsulants (k ~ 0.15 Wm-1K-1) limits the efficiency and power density of current phosphor conversion light emitting diodes (pc-LEDs). The technical objective of this project was to demonstrate synthesis and processing schemes for the fabrication of polymer hybrid encapsulants with a thermal conductivity exceeding k = 0.4 Wm-1K-1 for LED applications. The ‘hybrid polymer’ approach encompasses the dispersion of high thermal conductivity particle fillers (zinc oxide, ZnO as well as the alpha-polymorph of alumina, Al2O3) within a polysiloxane matrix (poly(dimethylsiloxane), PDMS as well as poly(phenyl methyl siloxane), PPMS) to increase the thermal conductivity while maintaining optical transparency and photothermal stability at levels consistent with LED applications. To accomplish this goal, a novel synthesis method for the fabrication of nanosized ZnO particles was developed and a novel surface chemistry was established to modify the surface of zinc oxide particle fillers and thus to enable their dispersion in poly(dimethyl siloxane) (PDMS) matrix polymers. Molecular dynamics and Mie simulations were used to optimize ligand structure and to enable the concurrent mixing of particles in PDMS/PPMS embedding media while also minimizing the thermal boundary resistance as well as optical scattering of particle fillers. Using this approach the synthesis of PDMS/ZnO hybrid encapsulants exhibiting a thermal conductivity of 0.64 Wm-1K-1 and optical transparency > 0.7 mm-1 was demonstrated. A forming process based on micromolding was developed to demonstrate the forming of particle filled PDMS into film and lens shapes. Photothermal stability testing revealed stability of the materials for approximately 4000 min when exposed to blue light LED (450 nm, 30 W/cm2). One postgraduate and seven graduate students were supported by the project. The research performed within this project led to fifteen publications in peer

  11. A self-calibrating led-based solar test platform

    DEFF Research Database (Denmark)

    Krebs, Frederik C; Sylvester-Hvid, Kristian O.; Jørgensen, Mikkel

    2011-01-01

    , it is possible to perform all the commonly employed measurements on the solar cell at very high speed without moving the sample. In particular, the LED-based illumination system provides an alternative to light-biased incident photon-to-current efficiency measurement to be performed which we demonstrate. Both......A compact platform for testing solar cells is presented. The light source comprises a multi-wavelength high-power LED (light emitting diode) array allowing the homogenous illumination of small laboratory solar cell devices (substrate size 50 × 25 mm) within the 390–940 nm wavelength range...... wavelengths intensities up to 10 suns is possible, and for a few wavelengths up to 30 suns can be reached. The setup is equipped with reference diodes and an optical fibre coupling enabling calibration, monitoring and control of the light impinging on the sample. Through a computer controlled interface...

  12. LED-based Illumination System for Solid-state Volumetric True 3D Display%用于固态体积式真三维立体显示的LED投影照明系统研究

    Institute of Scientific and Technical Information of China (English)

    冯奇斌; 牛红林; 华懿魁; 吕国强

    2011-01-01

    A solid-state volumetric true 3D display developed by Hefei University of Technology consists of a single DMD, an UHP lamp, a color wheel of RGBRGB and 240 Hz, a hollow light tunnel, 20 LC shutters, projection lens, folder mirrors, and control circuits etc., which have the disadvantages of low refresh rate and small color gamut. A LED-based illumination system is presented, comprising RGB LED modules, collimation lens, X-cube, and focusing lens to replace the UHP and the color wheel. The RGB LED modules emit RGB lights in sequence. The uniform RGB rectangular spots are produced at the end of the light tunnel. Without color wheel, the refresh rate could reach 60 Hz. The simulation and practical results show that the LED-based illumination system can completely satisfy the requirements of true 3D display.%合肥工业大学开发的固态体积式真三维立体显示器包括单片DMD、UHP投影光源、RGBRGB六段4倍速色轮、方棒、20层液晶光阀组成的显示体、投影镜头、折叠光路、控制电路等,存在刷新率低、色域小的问题.本文设计了基于LED的投影照明系统,包括RGB三原色LED发光模块、混合聚光镜、X棱镜等,替换样机中的UHP光源和色轮.红、绿、蓝LED顺序发光,光线经准直后进入X棱镜,在方棒的出射端顺序形成红、绿、蓝均匀矩形光斑.LED照明系统无需色轮分色,显示刷新率可达到60 Hz.仿真和试验结果证明本文设计的LED照明系统完全满足真三维立体显示的要求.

  13. A multicommuted stop-flow system employing LEDs-based photometer for the sequential determination of anionic and cationic surfactants in water

    Energy Technology Data Exchange (ETDEWEB)

    Lavorante, Andre F. [Centro de Energia Nuclear na Agricultura, Universidade de Sao Paulo, Av. Centenario 303, CP 96, 13400-970, Piracicaba, SP (Brazil); Morales-Rubio, Angel; Guardia, Miguel de la [Department of Analytical Chemistry, Faculty of Chemistry, University of Valencia, Research Building, 50 Dr. Moliner St., 46100 Burjassot, Valencia (Spain); Reis, Boaventura F. [Centro de Energia Nuclear na Agricultura, Universidade de Sao Paulo, Av. Centenario 303, CP 96, 13400-970, Piracicaba, SP (Brazil)], E-mail: reis@cena.usp.br

    2007-09-26

    It has been developed an automatic stop-flow procedure for sequential photometric determination of anionic and cationic surfactants in a same sample of water. The flow system was based on multicommutation process that was designed employing two solenoid micro-pumps and six solenoid pinch valves, which under microcomputer control carry out fluid propelling and reagent solutions handling. A homemade photometer using a photodiode as detector and two light emitting diodes (LEDs) with emission at 470 nm (blue) and 650 nm (red) as radiation sources, which was tailored to allow the determination of anionic and cationic surfactants in waters. The procedure for anionic surfactant determination was based on the substitution reaction of methyl orange (MO) by the anionic surfactant sodium dodecylbenzene sulfonate (DBS) to form an ion-pair with the cetyl pyridine chloride (CPC). Features such as a linear response ranging from 0.35 to 10.5 mg L{sup -1} DBS (R = 0.999), a detection limit of 0.06 mg L{sup -1} DBS and a relative standard deviation of 0.6% (n = 11) were achieved. For cationic surfactant determination, the procedure was based on the ternary complex formation between cationic surfactant, Fe(III) and chromazurol S (CAS) using CPC as reference standard solution. A linear response range between 0.34 and 10.2 mg L{sup -1} CPC (R = 0.999), a detection limit of 0.05 mg L{sup -1} CPC and a relative standard deviation of 0.5% (n = 11) were obtained. In both cases, the sampling throughput was 60 determinations per hour. Reagents consumption of 7.8 {mu}g MO, 8.2 {mu}g CPC, 37.2 {mu}g CAS and 21.6 {mu}g Fe(III) per determination were achieved. Analyzing river water samples and applying t-test between the results found and those obtained using reference procedures for both surfactant types provide no significant differences at 95% confidence level.

  14. Design of an elliptic spot illumination system in LED-based color filter-liquid-crystal-on-silicon pico projectors for mobile embedded projection.

    Science.gov (United States)

    Chen, Enguo; Yu, Feihong

    2012-06-01

    We present an elliptic spot illumination system for a color filter-liquid-crystal-on-silicon (CF-LCoS) pico projector employing a specifically designed free-form lens and a cylindrical lens to improve on previous designs in terms of optical efficiency while yielding an ultracompact and low-cost optical architecture. The detailed design description of the optical system is thoroughly investigated. Simulation results coincide well with the theoretical calculation. The single 1  mm×1  mm LED chip-powered optical engine, which employs a CF-LCoS panel with a diagonal of 0.28 in and an aspect ratio of 4:3, has an estimated output efficiency over 9.8% (11.8 lm@1 W) and an ANSI 9-point uniformity over 88.5%, with the ultrasmall volume 24  mm×19  mm×7  mm. Compared to the circular spot-illuminated projection system, a total increment of about 23% of system efficiency is available with this improved optical engine. It is believed that there would be a huge market potential to commercialize our design.

  15. Testing of a simplified LED based vis/NIR system for rapid ripeness evaluation of white grape (Vitis vinifera L.) for Franciacorta wine.

    Science.gov (United States)

    Giovenzana, Valentina; Civelli, Raffaele; Beghi, Roberto; Oberti, Roberto; Guidetti, Riccardo

    2015-11-01

    The aim of this work was to test a simplified optical prototype for a rapid estimation of the ripening parameters of white grape for Franciacorta wine directly in field. Spectral acquisition based on reflectance at four wavelengths (630, 690, 750 and 850 nm) was proposed. The integration of a simple processing algorithm in the microcontroller software would allow to visualize real time values of spectral reflectance. Non-destructive analyses were carried out on 95 grape bunches for a total of 475 berries. Samplings were performed weekly during the last ripening stages. Optical measurements were carried out both using the simplified system and a portable commercial vis/NIR spectrophotometer, as reference instrument for performance comparison. Chemometric analyses were performed in order to extract the maximum useful information from optical data. Principal component analysis (PCA) was performed for a preliminary evaluation of the data. Correlations between the optical data matrix and ripening parameters (total soluble solids content, SSC; titratable acidity, TA) were carried out using partial least square (PLS) regression for spectra and using multiple linear regression (MLR) for data from the simplified device. Classification analysis were also performed with the aim of discriminate ripe and unripe samples. PCA, MLR and classification analyses show the effectiveness of the simplified system in separating samples among different sampling dates and in discriminating ripe from unripe samples. Finally, simple equations for SSC and TA prediction were calculated. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Autonomous photovoltaic lighting system

    OpenAIRE

    Ahmed A. A. Hafez; Montesinos Miracle, Daniel; Sudrià Andreu, Antoni

    2012-01-01

    This paper introduces a comparison between the conventional and Photovoltaic (PV) lighting systems. A simple sizing procedure for a PV stand-alone system was advised. The paper also proposes a novel PV lighting system. The proposed system is simple, compact and reliable. The system operation was investigated by thoroughly mathematical and simulation work.

  17. LED-based digital diameter measurement

    Science.gov (United States)

    Kleuver, Wolfram; Becker, Lothar

    1995-01-01

    This paper presents a new industrial sensor for measuring diameters of extreme thin objects. The system is divided in two parts. The first is the emitter and the second the receiver. It is possible to use this system for the automatic inspection of files and wires in the textile industries and wire works. Another application for the sensor is the control of production of chemical files in an extruder. Furthermore we can measure more than one object in the lightbeam because we get information not only about the dimensions also about the position of the objects in the beam. The innovation in this system is the using of a light emitting diode (LED) as emitter and the realization of a long distance of about two or more meters between the two sensorheads. The results of this development are a special kind of optical layout in the emitter to reduce the loss of intensity and minimize the divergence of the lightbeam. It is not necessary to develop an intensity distribution, which is equal over the complete width of the sensorhead. We can show that we have a better dynamic in the system with this feature. The experiments prove that we get the same resolution as a laserbeamsensor. Furthermore one advantage is the eye-safety.

  18. Natural light illumination system.

    Science.gov (United States)

    Whang, Allen Jong-Woei; Chen, Yi-Yung; Yang, Shu-Hua; Pan, Po-Hsuan; Chou, Kao-Hsu; Lee, Yu-Chi; Lee, Zong-Yi; Chen, Chi-An; Chen, Cheng-Nan

    2010-12-10

    In recent years, green energy has undergone a lot of development and has been the subject of many applications. Many research studies have focused on illumination with sunlight as a means of saving energy and creating healthy lighting. Natural light illumination systems have collecting, transmitting, and lighting elements. Today, most daylight collectors use dynamic concentrators; these include Sun tracking systems. However, this design is too expensive to be cost effective. To create a low-cost collector that can be easily installed on a large building, we have designed a static concentrator, which is prismatic and cascadable, to collect sunlight for indoor illumination. The transmission component uses a large number of optical fibers. Because optical fibers are expensive, this means that most of the cost for the system will be related to transmission. In this paper, we also use a prismatic structure to design an optical coupler for coupling n to 1. With the n-to-1 coupler, the number of optical fibers necessary can be greatly reduced. Although this new natural light illumination system can effectively guide collected sunlight and send it to the basement or to other indoor places for healthy lighting, previously there has been no way to manage the collected sunlight when lighting was not desired. To solve this problem, we have designed an optical switch and a beam splitter to control and separate the transmitted light. When replacing traditional sources, the lighting should have similar characteristics, such as intensity distribution and geometric parameters, to those of traditional artificial sources. We have designed, simulated, and optimized an illumination lightpipe with a dot pattern to redistribute the collected sunlight from the natural light illumination system such that it equals the qualities of a traditional lighting system. We also provide an active lighting module that provides lighting from the natural light illumination system or LED auxiliary

  19. Integral freeform illumination lens design of LED based pico-projector.

    Science.gov (United States)

    Zhao, Shuang; Wang, Kai; Chen, Fei; Qin, Zong; Liu, Sheng

    2013-05-01

    In this paper, an illumination lens design for a LED-based pico-projector is presented. Different from the traditional illumination systems composed by lens group, the integral illumination lens consists of a total internal reflector (TIR) and a freeform surface. TIR acts as collimation lens and its top surface formed by a freeform surface reshapes the nonuniform circular light pattern generated by TIR to be rectangular and uniform. Diameter and height of the lens are 16 and 10 mm, respectively. An optimization method to deal with the problem of extended light source is also presented in detail in this paper. According to the simulation results of the final optimized lens, 77% (neglecting the effect of polarization) of the power of light source is collected on liquid crystal on silicon panel with a 16∶9 ratio and illumination uniformity achieves 92%.

  20. LEDs based on conjugated PPV block copolymers

    NARCIS (Netherlands)

    Brouwer, H.J.; Hilberer, A.; Krasnikov, V.V.; Werts, M.; Wildeman, J.; Hadziioannou, G.

    1997-01-01

    A way to control the bandgap in semi-conducting polymers is by preparing polymers with a partially conjugated backbone. In our laboratory, three conjugated copolymers containing PPV trimers as light emitting chromophores have been synthesized, which emit in the blue, green and orange wavelength regi

  1. Pupillary efficient lighting system

    Science.gov (United States)

    Berman, Samuel M.; Jewett, Don L.

    1991-01-01

    A lighting system having at least two independent lighting subsystems each with a different ratio of scotopic illumination to photopic illumination. The radiant energy in the visible region of the spectrum of the lighting subsystems can be adjusted relative to each other so that the total scotopic illumination of the combined system and the total photopic illumination of the combined system can be varied independently. The dilation or contraction of the pupil of an eye is controlled by the level of scotopic illumination and because the scotopic and photopic illumination can be separately controlled, the system allows the pupil size to be varied independently of the level of photopic illumination. Hence, the vision process can be improved for a given level of photopic illumination.

  2. Inexpensive LED-based spectrophotometer for analyzing optical coatings

    CERN Document Server

    Hardie, Kayla; Kuntz, Katanya B; Jennewein, Thomas

    2016-01-01

    Optical coatings are widespread in everyday life, from camera lenses to glasses, to complex optics experiments. A simple, reliable device that can quickly and inexpensively analyze optical coatings is a valuable laboratory tool. Such a device can identify unknown or mislabelled optics, and characterize the transmission spectra of optical elements used in an experiment. We present the design and characterization of a LED-based spectrophotometer, and demonstrate its ability to identify different optical coatings. Our approach uses ten LEDs that cover a spectrum from 365 nm to 1000 nm. A small servomotor and microcontroller rotates a LED board to sequentially position each LED over an optical sample, and the transmitted light corresponding to each LED is measured with a silicon photodetector. The device is automated, portable, inexpensive, user-friendly and simple to build.

  3. Grid converter for LED based intelligent light sources

    DEFF Research Database (Denmark)

    Török, Lajos

    to reduce the size of the magnetic components. A description of different grid regulations was given followed by a set of converter topologies and controllers. Different control techniques were pointed out. Among the listed topologies and control solutions few were selected for further analysis, design...... controllers can be designed. The controller design was interconnected with the hardware design and control platform. Thus two dfferent prototypes were designed and built with two dierent digital controllers and the controller design, analysis and implementation was based on these two case studies. The first...... of the PI controller. All four control loops were implemented in a 16 bitfixed point dsPIC33FJ32GS406 microcontroller driving at the same time 8 PWM channels. Finally a brief analysis was done on the eect of the grid disturbances, especially voltage sags on the digital controller. Dierent grid codes...

  4. LED-based near infrared sensor for cancer diagnostics

    Science.gov (United States)

    Bogomolov, Andrey; Ageev, Vladimir; Zabarylo, Urszula; Usenov, Iskander; Schulte, Franziska; Kirsanov, Dmitry; Belikova, Valeria; Minet, Olaf; Feliksberger, E.; Meshkovsky, I.; Artyushenko, Viacheslav

    2016-03-01

    Optical spectroscopic technologies are increasingly used for cancer diagnostics. Feasibility of differentiation between malignant and healthy samples of human kidney using Fluorescence, Raman, MIR and NIR spectroscopy has been recently reported . In the present work, a simplification of NIR spectroscopy method has been studied. Traditional high-resolution NIR spectrometry was replaced by an optical sensor based on a set of light-emitting diodes at selected wavelengths as light sources and a photodiode. Two prototypes of the sensor have been developed and tested using 14 in-vitro samples of seven kidney tumor patients. Statistical evaluation of results using principal component analysis and partial least-squares discriminant analysis has been performed. Despite only partial discrimination between tumor and healthy tissue achieved by the presented new technique, the results evidence benefits of LED-based near-infrared sensing used for oncological diagnostics. Publisher's Note: This paper, originally published on 4 March, 2016, was replaced with a corrected/revised version on 7 April, 2016. If you downloaded the original PDF but are unable to access the revision, please contact SPIE Digital Library Customer Service for assistance.

  5. Nonlinearity measurements of solar cells with an LED-based combinatorial flux addition method.

    Science.gov (United States)

    Hamadani, Behrang H; Shore, Andrew; Roller, John; Yoon, Howard W; Campanelli, Mark

    2016-02-01

    We present a light emitting diode (LED)-based system utilizing a combinatorial flux addition method to investigate the nonlinear relationship in solar cells between the output current of the cell and the incident irradiance level. The magnitude of the light flux is controlled by the supplied currents to two LEDs (or two sets of them) in a combinatorial fashion. The signals measured from the cell are arranged within a related overdetermined linear system of equations derived from an appropriately chosen N(th) degree polynomial representing the relationship between the measured signals and the incident fluxes. The flux values and the polynomial coefficients are then solved for by linear least squares to obtain the best fit. The technique can be applied to any solar cell, under either monochromatic or broadband spectrum. For the unscaled solution, no reference detectors or prior calibrations of the light flux are required. However, if at least one calibrated irradiance value is known, then the entire curve can be scaled to an appropriate spectral responsivity value. Using this technique, a large number of data points can be obtained in a relatively short time scale over a large signal range.

  6. Lighting system with illuminance control

    DEFF Research Database (Denmark)

    2013-01-01

    The present invention relates to an illumination control system comprising a plurality of outdoor luminaries and a motorized service vehicle. Each luminaire comprises a controllable light source producing a light illuminance. The motorized service vehicle comprises a light sensor configured...... to detect the light illuminance generated by the controllable light source at the motorized service vehicle. The motorized service vehicle computes light illuminance data based on the detected light illuminance and transmits these to the outdoor luminaire through a wireless communication link or stores...... the light illuminance data on a data recording device of the motorized service vehicle. The outdoor luminaire receives may use the light illuminance data to set or adjust a light illuminance of the controllable light source....

  7. Lighting system with thermal management system

    Science.gov (United States)

    Arik, Mehmet; Weaver, Stanton; Stecher, Thomas; Seeley, Charles; Kuenzler, Glenn; Wolfe, Jr., Charles; Utturkar, Yogen; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2013-05-07

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  8. Lighting system with thermal management system

    Energy Technology Data Exchange (ETDEWEB)

    Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Seeley, Charles Erklin; Kuenzler, Glenn Howard; Wolfe, Jr, Charles Franklin; Utturkar, Yogen Vishwas; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2016-10-11

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  9. Experimental study of porous media flow using hydro-gel beads and LED based PIV

    Science.gov (United States)

    Harshani, H. M. D.; Galindo-Torres, S. A.; Scheuermann, A.; Muhlhaus, H. B.

    2017-01-01

    A novel experimental approach for measuring porous flow characteristics using spherical hydro-gel beads and particle image velocimetry (PIV) technique is presented. A transparent porous medium consisting of hydro-gel beads that are made of a super-absorbent polymer, allows using water as the fluid phase while simultaneously having the same refractive index. As a result, a more adaptable and cost effective refractive index matched (RIM) medium is created. The transparent nature of the porous medium allows optical systems to visualize the flow field by using poly-amide seeding particles (PSP). Low risk light emitting diode (LED) based light was used to illuminate the plane in order to track the seeding particles’ path for the characterization of the flow inside the porous medium. The system was calibrated using a manually measured flow by a flow meter. Velocity profiles were obtained and analysed qualitatively and quantitatively in order to characterise the flow. Results show that this adaptable, low risk experimental set-up can be used for flow measurements in porous medium under low Reynolds numbers. The limitations of using hydro-gel beads are also discussed.

  10. Bright infrared LEDs based on colloidal quantum-dots

    KAUST Repository

    Sun, Liangfeng

    2013-01-01

    Record-brightness infrared LEDs based on colloidal quantum-dots have been achieved through control of the spacing between adjacent quantum-dots. By tuning the size of quantum-dots, the emission wavelengths can be tuned between 900nm and 1650nm. © 2013 Materials Research Society.

  11. A novel LED-based device for occlusal caries detection.

    Science.gov (United States)

    Aktan, Ali Murat; Cebe, Mehmet Ata; Ciftçi, Mehmet Ertuğrul; Sirin Karaarslan, Emine

    2012-11-01

    The aim of this in-vitro study was to compare the performance of laser-based (DIAGNOdent, KaVo, Biberach, Germany) and LED-based (Midwest Caries I.D., DENTSPLY Professional, New York, USA) caries detectors in the detection of occlusal caries in permanent molars. The study consisted of 129 visually sound or non-cavitated pits or fissures in 82 extracted permanent human molar teeth. Two trained examiners used the laser-based and LED-based caries detectors to examine the fissures for caries. The teeth were then sectioned at the surfaces suspected of containing occlusal caries and histologically evaluated using stereomicroscopy as a gold standard. Inter-examiner reliability of the caries detector examination was assessed using Cohen's Kappa statistics. The sensitivity, specificity, and accuracy in diagnosing occlusal caries using the two devices were calculated according to appropriate cut-off scores. Receiver operating characteristic (ROC) curves were also determined to compare the diagnostic performance of the devices in occlusal caries diagnosis. The cut-off level of significance was taken as p = 0.005. Cohen's Kappa showed substantial agreement for the laser-based caries detector (0.74), and almost perfect agreement for the LED-based (0.89) caries detector. The specificity of the laser-based device varied from 0.49 to 0.97 at T1 and T2. Its sensitivity varied from 0.33 to 0.65 at T1 and T2. The specificity of the LED-based device varied from 0.48 to 0.56 at T1 and T2. Its sensitivity varied from 0.65 to 0.84 at T1 and from 0.80 to 0.84 at T2. Taking the limitations of the current study into consideration, the DIAGNOdent laser pen was more accurate in determining when teeth were free of occlusal caries than was the Midwest Caries I.D. LED-based device, although the Midwest Caries I.D. device more often revealed the presence of occlusal caries than did the DIAGNOdent pen.

  12. Optical design of LED-based automotive tail lamps

    Science.gov (United States)

    Domhardt, André; Rohlfing, Udo; Klinger, Karsten; Manz, Karl; Kooß, Dieter; Lemmer, Uli

    2007-09-01

    The application of ultra bright monochromatic and white High-Power-LEDs in the range of automotive lighting systems is now state of the art. These LEDs offer new possibilities in optical design and engineering within different fields of automotive lighting, e.g., tail lamps, signal lamps, headlamps and interior lighting. This contribution describes the process of the optical design of an automotive LED tail lamp based on a practical example. We will elaborate the principal geometric approach, the radiometric conditions and the optical design by using standard and advanced mathematical optimization methods. Special attention will be paid to the following topics: efficient light coupling from the LED into the optical device, adaptation of the illuminance and optimization with respect to the requirements from SAE/ECE regulations. It will be shown that the development of LED-lamps requires the complex interaction of several factors. The challenge for the optical designer is to fulfill the technical demands while also considering the appearance of the final product desired by the customer. Further design specifications emerge from the electrical and thermal layout of the lamp.

  13. 33 CFR 127.109 - Lighting systems.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Lighting systems. 127.109 Section... Waterfront Facilities Handling Liquefied Natural Gas § 127.109 Lighting systems. (a) The marine transfer area for LNG must have a lighting system and separate emergency lighting. (b) All outdoor lighting must be...

  14. Self-aligning LED-based optical link

    Science.gov (United States)

    Shen, Thomas C.; Drost, Robert J.; Rzasa, John R.; Sadler, Brian M.; Davis, Christopher C.

    2016-09-01

    The steady advances in light-emitting diode (LED) technology have motivated the use of LEDs in optical wireless communication (OWC) applications such as indoor local area networks (LANs) and communication between mobile platforms (e.g., robots, vehicles). In contrast to traditional radio frequency (RF) wireless communication, OWC utilizes electromagnetic spectrum that is largely unregulated and unrestricted. OWC communication may be especially useful in RF-denied environments, in which RF communication may be prohibited or undesirable. However, OWC does present some challenges, including the need to maintain alignment between potentially moving nodes. We describe a novel system for link alignment that is composed of a hyperboloidal mirror, camera, and gimbal. The experimental system is able to use the mirror and camera to detect an LED beacon of a neighboring node and estimate its bearing (azimuth and elevation), point the gimbal towards the beacon, and establish an optical link.

  15. Light-emitting diode-based multiwavelength diffuse optical tomography system guided by ultrasound

    Science.gov (United States)

    Yuan, Guangqian; Alqasemi, Umar; Chen, Aaron; Yang, Yi; Zhu, Quing

    2014-01-01

    Abstract. Laser diodes are widely used in diffuse optical tomography (DOT) systems but are typically expensive and fragile, while light-emitting diodes (LEDs) are cheaper and are also available in the near-infrared (NIR) range with adequate output power for imaging deeply seated targets. In this study, we introduce a new low-cost DOT system using LEDs of four wavelengths in the NIR spectrum as light sources. The LEDs were modulated at 20 kHz to avoid ambient light. The LEDs were distributed on a hand-held probe and a printed circuit board was mounted at the back of the probe to separately provide switching and driving current to each LED. Ten optical fibers were used to couple the reflected light to 10 parallel photomultiplier tube detectors. A commercial ultrasound system provided simultaneous images of target location and size to guide the image reconstruction. A frequency-domain (FD) laser-diode-based system with ultrasound guidance was also used to compare the results obtained from those of the LED-based system. Results of absorbers embedded in intralipid and inhomogeneous tissue phantoms have demonstrated that the LED-based system provides a comparable quantification accuracy of targets to the FD system and has the potential to image deep targets such as breast lesions. PMID:25473884

  16. Colour shift and mechanism investigation on the PMMA diffuser used in LED-based luminaires

    Science.gov (United States)

    Lu, Guangjun; van Driel, W. D.; Fan, Xuejun; Yazdan Mehr, M.; Fan, Jiajie; Qian, Cheng; Jansen, K. M. B.; Zhang, G. Q.

    2016-04-01

    PMMA material is widely used in LED-based luminaires due to several advantages such as excellent optical transparency, durability against radiation, surface hardness (scratch free), rigidity and strength and can be completely recycled. However, few studies have been reported on the colour shift and failure mechanisms caused by this type of material. This paper experimentally investigated PMMA materials with different aging conditions. The following conclusions could be drawn. (1) Discolouration was not observed for any sample subjected to aging of 85 °C for 5000 h, or with additional blue light irradiation for 5000 h, or with additional humidity of 85%RH for 5000 h, or even with aging of 100 °C for 3000 h. (2) The specimen subjected to aging of 150 °C for 360 h has a surface discoloration and has a significant wavelength dependent degradation in the transmission spectrum caused by oxidation. The specimen with aging of 100 °C for 3000 h has a less oxidation, although no significant transmission spectrum reduction was observed. (3) Using such aged specimen as a diffuser mounted on a LED-based luminaire, the radiant flux peak intensity in the blue light area has a more severe reduction than that in the yellow light area, which results in a reduction of the radiant flux intensity ratio of blue light to yellow light and hence induces the colour shift to yellow. The colour shift investigated is 0.005, very close to the general failure criterion of 0.007, while the lumen decay is 10.2%, far less than the failure criterion of 30%.

  17. Dynamic light intensity detection system of aerodrome assistance light

    Science.gov (United States)

    Gao, Jianshu; Song, Jiye; Yu, Zhijing; Chen, Fei; Shi, Xudong; Gao, Qingji

    2007-11-01

    The techniques used in dynamic detection of airfield lighting intensity are introduced in this paper. These techniques can take place of the old method of checking all manually, and the system can detect the lights intensity online quickly and exactly, so as to find out the light faults and ensure the safety of planes taking off, landing and slipping. The system uses a car with a string of sensors which have been cosine calibrated and v(λ) calibrated to detect the light intensity. When the car is moving, the sensors can detect the lights' horizontal section. To accurately measure the distance from the measured aerodrome assistance light to the moving car, and then calculate the light intensity and protract the iso-candela curve, the Doppler ranging radar system is used. To guarantee the dependability of the system and the measurement precision, a video monitoring and guiding system is used to assure the car to run along the airfield lights line, then light orientation sensors are used to eliminate the radar's cumulating errors. The experiment indicates that this system is feasible and has high detecting precision.

  18. Cost effectiveness of new roadway lighting systems

    Directory of Open Access Journals (Sweden)

    Yi Jiang

    2015-06-01

    Full Text Available Appropriate and adequate lighting at select locations on roadways is essential for roadway safety. As the lighting technologies advance, many types of new lighting devices have been developed for roadway lightings. The most promising new lighting technologies for roadway lighting include light emitting diode, induction, plasma, and metal halide lighting systems. A study was conducted to compare the new systems with the conventional high pressure sodium systems that are currently used on the Indiana roadway systems. In this study, the engineering issues, were analyzed such as illuminance, color rendering, power usage, cost effectiveness, and approval procedures for new roadway lighting systems. This paper, however, presents only the study findings related to cost effectiveness of the evaluated roadway lighting systems. Illustrated in this paper are the main features of the roadway lighting systems under evaluations, installations of the new lighting systems, measurements of power consumptions, and life cycle cost analyses of the lighting systems. Through this study, experience and knowledge have been obtained on the installations, power measurements, and cost effectiveness of the new types of the roadway lighting devices. The actual power values of various luminaires were obtained by measuring the electric current with a multi-meter. It was found that the differences between the rated and measured power values could be significant. The results of the life cycle cost analysis indicate that the lower life cycle costs of some of the alternative lighting devices are attributed to their relatively lower electricity usages and longer lamp/emitter replacement cycles.

  19. Green Lighting. Energy-efficient integrated lighting systems - Final report

    Energy Technology Data Exchange (ETDEWEB)

    Linhart, F.; Scartezzini, J.-L.

    2009-10-15

    The objective of the Green Lighting project was to develop a High Performance Integrated Lighting System, based on advanced technologies for day- and electric lighting, achieving a Lighting Power Density (LPD) that does not exceed 3 W/m{sup 2}. The project has revealed that Anidolic Daylighting Systems (ADS) are an ideal basis for High Performance Integrated Lighting Systems. Not only are they able to provide adequate illumination (i.e. sufficiently high illuminance) in office rooms during large fractions of normal office hours, under various sky conditions and over the entire year, but they are also highly appreciated by office occupants at the condition that glare control mechanisms are available. Complementary electric lighting is, however, still necessary to back up the ADS at times when there is insufficient daylight flux available. It was shown during this project, that the most interesting trade-offs between energy-efficiency and visual comfort are obtained by using a combination of ceiling-mounted directly emitting luminaires with very high optical efficiencies for ambient lighting and portable desk lamps for temporary task lighting. The most appropriate lamps for the ceiling-mounted luminaires are currently highly efficient fluorescent tubes, but white LED tubes can be considered a realistic option for the future. The most suitable light sources for desk lamps for temporary task lighting are Compact Fluorescent Lamps (CFLs) and white LED light bulbs. Based on the above-mentioned technologies, a High Performance Integrated Lighting System with a very low LPD has been developed over the last three years. The system has been set up in an office room of the LESO solar experimental building located on the EPFL campus; it has been tested intensively during a Post-Occupancy Evaluation (POE) study involving twenty human subjects. This study has revealed that the subjects' performance and subjective visual comfort was improved by the new system, compared to

  20. Resonances in -light nucleus systems

    Indian Academy of Sciences (India)

    K P Khemchandani; N G Kelkar; M Nowakowski; B K Jain

    2006-04-01

    We locate resonances in -light nucleus elastic scattering using the time delay method. We solve few-body equations within the finite rank approximation in order to calculate the -matrices and hence the time delay for the - 3He and - 4He systems. We find a resonance very close to the threshold in - 3 He elastic scattering, at about 0.5 MeV above threshold with a width of ∼ 2 MeV. The calculations also hint at the presence of sub-threshold states in both the cases.

  1. Lighting Systems Control for Demand Response

    NARCIS (Netherlands)

    Husen, S.A.; Pandharipande, A.; Tolhuizen, L.M.G.; Wang, Y.; Zhao, M.

    2012-01-01

    Lighting is a major part of energy consumption in buildings. Lighting systems will thus be one of the important component systems of a smart grid for dynamic load management services like demand response.In the scenario considered in this paper, under a demand response request, lighting systems in a

  2. Optimization of light quality from color mixing light-emitting diode systems for general lighting

    DEFF Research Database (Denmark)

    Thorseth, Anders

    2012-01-01

    To address the problem of spectral light quality from color mixing light-emitting diode systems, a method for optimizing the spectral output of multicolor LED system with regards to standardized quality parameters has been developed. The composite spectral power distribution from the LEDs...... boundaries mapping the capabilities of the simulated lighting system....

  3. Implementation and Test of a LED-Based Lamp for a Lighthouse

    Directory of Open Access Journals (Sweden)

    Luca Mercatelli

    2014-01-01

    Full Text Available A novel sustainable source was developed for an existing Italian lighthouse, exploiting the light emitting diode (LED technology and the norms evolution. The research work started with the optical design of the device, while this work concerns the realization, installation, and test of the new LED lamp. The lamp recombines multiple separated LEDs, realizing a quasipunctual localized source. After installation in the lighthouse, specific photometric tests verified that the proposed power-saving source satisfied the illumination requirements of the marine signaling norms. The advantages of the LED-based lamp are reduced energy consumption, enhanced efficiency, longer life, decreased faults, slower aging, and lower maintenance costs. The obtained LED signalling device is more durable and reliable. In the future the application of these power-saving long-life sources could be extended to other maritime signaling devices or to other traffic signs.

  4. Light relations in orchard systems

    NARCIS (Netherlands)

    Wagenmakers, P.S.

    1995-01-01

    The optimization of light interception is essential for the production of highquality fruit. High light interception is required for high yields, whereas insufficient light exposure may lead to inferior flowering and a reduction of many characteristics of fruit quality. Orchard

  5. Light relations in orchard systems

    NARCIS (Netherlands)

    Wagenmakers, P.S.

    1995-01-01

    The optimization of light interception is essential for the production of highquality fruit. High light interception is required for high yields, whereas insufficient light exposure may lead to inferior flowering and a reduction of many characteristics of fruit quality. Orchard configuratio

  6. An Efficient LED System-in-Module for General Lighting Applications

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2008-09-14

    The objective of the project was to realize an LED-based lighting technology platform for general illumination, starting with LED chips, and integrating the necessary technologies to make compact, user-friendly, high-efficiency, energy-saving sources of controlled white (or variable-colored) light. The project is to build the system around the LEDs, and not to work on the LEDs themselves, in order that working products can be introduced soon after the LEDs reach suitable efficiency for mass-production of high-power light sources for general illumination. Because the light sources are intended for general illumination, color must be accurately maintained, requiring feedback control in the electronics. The project objective has been realized and screw base demonstrators, based on the technology developed in the project, have been built.

  7. Advanced Light Source control system

    Energy Technology Data Exchange (ETDEWEB)

    Magyary, S.; Chin, M.; Cork, C.; Fahmie, M.; Lancaster, H.; Molinari, P.; Ritchie, A.; Robb, A.; Timossi, C.

    1989-03-01

    The Advanced Light Source (ALS) is a third generation 1--2 GeV synchrotron radiation source designed to provide ports for 60 beamlines. It uses a 50 MeV electron linac and 1.5 GeV, 1 Hz, booster synchrotron for injection into a 1--2 GeV storage ring. Interesting control problems are created because of the need for dynamic closed beam orbit control to eliminate interaction between the ring tuning requirements and to minimize orbit shifts due to ground vibrations. The extremely signal sensitive nature of the experiments requires special attention to the sources of electrical noise. These requirements have led to a control system design which emphasizes connectivity at the accelerator equipment end and a large I/O bandwidth for closed loop system response. Not overlooked are user friendliness, operator response time, modeling, and expert system provisions. Portable consoles are used for local operation of machine equipment. Our solution is a massively parallel system with >120 Mbits/sec I/O bandwidth and >1500 Mips computing power. At the equipment level connections are made using over 600 powerful Intelligent Local Controllers (ILC-s) mounted in 3U size Eurocard slots using fiber-optic cables between rack locations. In the control room, personal computers control and display all machine variables at a 10 Hz rate including the scope signals which are collected though the control system. Commercially available software and industry standards are used extensively. Particular attention is paid to reliability, maintainability and upgradeability. 10 refs., 11 figs.

  8. Photodynamics of Light Harvesting Systems

    NARCIS (Netherlands)

    Ruijter, Ward Piet Frans de

    2005-01-01

    Light harvesting (LH) lies at the basis of photosynthesis, the process in which energy from the sun is stored by a photochemical reaction. The photophysics of light absorption and energy transfer is the key to a detailed understanding of the first steps in this process. This thesis describes the

  9. Photodynamics of Light Harvesting Systems

    NARCIS (Netherlands)

    Ruijter, Ward Piet Frans de

    2005-01-01

    Light harvesting (LH) lies at the basis of photosynthesis, the process in which energy from the sun is stored by a photochemical reaction. The photophysics of light absorption and energy transfer is the key to a detailed understanding of the first steps in this process. This thesis describes the inv

  10. Lighting for remote viewing systems

    Energy Technology Data Exchange (ETDEWEB)

    Draper, J.V.

    1984-01-01

    Scenes viewed by television do not provide the same channels of information for judgement of distances as scenes viewed directly, since television eliminates or degrades several depth perception cues. However, it may be possible to improve depth perception of televised scenes by enhancing the information available through depth cues that are available from lighting. A literature survey and expert opinions were integrated to design a remote lighting arrangement which could enhance depth perception of operators performing remote handling operations. This paper describes the lighting arrangement and discusses some of its advantages and disadvantages. 10 references, 2 figures.

  11. Lighting for remote viewing systems

    Energy Technology Data Exchange (ETDEWEB)

    Draper, J.V.

    1984-01-01

    Scenes viewed by television do not provide the same channels of information for judgment of distances as scenes viewed directly, since television eliminates or degrades several depth perception cues. However, it may be possible to improve depth perception of televised scenes by enhancing the information available through depth cues that are available from lighting. A literature survey and expert opinions were integrated to design a remote lighting arrangement which could enhance depth perception of operators performing remote handling operations. This paper describes the lighting arrangement and discusses some of its advantages and disadvantages. 10 references, 2 figures.

  12. Lighting

    Data.gov (United States)

    Federal Laboratory Consortium — Lighting Systems Test Facilities aid research that improves the energy efficiency of lighting systems. • Gonio-Photometer: Measures illuminance from each portion of...

  13. Light distribution system comprising spectral conversion means

    DEFF Research Database (Denmark)

    2012-01-01

    System (200, 300) for the distribution of white light, having a supply side (201, 301, 401) and a delivery side (202, 302, 402), the system being configured for guiding light with a multitude of visible wavelengths in a propagation direction P from the supply side to the distribution side...

  14. Hybrid solar lighting distribution systems and components

    Science.gov (United States)

    Muhs, Jeffrey D.; Earl, Dennis D.; Beshears, David L.; Maxey, Lonnie C.; Jordan, John K.; Lind, Randall F.

    2011-07-05

    A hybrid solar lighting distribution system and components having at least one hybrid solar concentrator, at least one fiber receiver, at least one hybrid luminaire, and a light distribution system operably connected to each hybrid solar concentrator and each hybrid luminaire. A controller operates all components.

  15. Hybrid solar lighting systems and components

    Science.gov (United States)

    Muhs, Jeffrey D.; Earl, Dennis D.; Beshears, David L.; Maxey, Lonnie C.; Jordan, John K.; Lind, Randall F.

    2007-06-12

    A hybrid solar lighting system and components having at least one hybrid solar concentrator, at least one fiber receiver, at least one hybrid luminaire, and a light distribution system operably connected to each hybrid solar concentrator and each hybrid luminaire. A controller operates each component.

  16. Squeezed light in optomechanical systems

    DEFF Research Database (Denmark)

    Harris, G. I.; Taylor, M. A.; Hoff, Ulrich Busk

    2012-01-01

    Squeezed light enhanced optomechanical measurements are demonstrated in both intra-cavity and biological contexts, with respective enhancements of 1.0 and 2.7 dB. Quantum enhanced microrheology of the cytoplasm of a yeast cell is thereby realized.......Squeezed light enhanced optomechanical measurements are demonstrated in both intra-cavity and biological contexts, with respective enhancements of 1.0 and 2.7 dB. Quantum enhanced microrheology of the cytoplasm of a yeast cell is thereby realized....

  17. LED Context Lighting System in Residential Areas

    Directory of Open Access Journals (Sweden)

    Sook-Youn Kwon

    2014-01-01

    Full Text Available As issues of environment and energy draw keen interest around the globe due to such problems as global warming and the energy crisis, LED with high optical efficiency is brought to the fore as the next generation lighting. In addition, as the national income level gets higher and life expectancy is extended, interest in the enhancement of life quality is increasing. Accordingly, the trend of lightings is changing from mere adjustment of light intensity to system lighting in order to enhance the quality of one’s life as well as reduce energy consumption. Thus, this study aims to design LED context lighting system that automatically recognizes the location and acts of a user in residential areas and creates an appropriate lighting environment. The proposed system designed in this study includes three types of processing: first, the creation of a lighting environment index suitable for the user’s surroundings and lighting control scenarios and second, it measures and analyzes the optical characteristics that change depending on the dimming control of lighting and applies them to the index. Lastly, it adopts PIR, piezoelectric, and power sensor to grasp the location and acts of the user and create a lighting environment suitable for the current context.

  18. LED context lighting system in residential areas.

    Science.gov (United States)

    Kwon, Sook-Youn; Im, Kyoung-Mi; Lim, Jae-Hyun

    2014-01-01

    As issues of environment and energy draw keen interest around the globe due to such problems as global warming and the energy crisis, LED with high optical efficiency is brought to the fore as the next generation lighting. In addition, as the national income level gets higher and life expectancy is extended, interest in the enhancement of life quality is increasing. Accordingly, the trend of lightings is changing from mere adjustment of light intensity to system lighting in order to enhance the quality of one's life as well as reduce energy consumption. Thus, this study aims to design LED context lighting system that automatically recognizes the location and acts of a user in residential areas and creates an appropriate lighting environment. The proposed system designed in this study includes three types of processing: first, the creation of a lighting environment index suitable for the user's surroundings and lighting control scenarios and second, it measures and analyzes the optical characteristics that change depending on the dimming control of lighting and applies them to the index. Lastly, it adopts PIR, piezoelectric, and power sensor to grasp the location and acts of the user and create a lighting environment suitable for the current context.

  19. Solid State Lighting Reliability Components to Systems

    CERN Document Server

    Fan, XJ

    2013-01-01

    Solid State Lighting Reliability: Components to Systems begins with an explanation of the major benefits of solid state lighting (SSL) when compared to conventional lighting systems including but not limited to long useful lifetimes of 50,000 (or more) hours and high efficacy. When designing effective devices that take advantage of SSL capabilities the reliability of internal components (optics, drive electronics, controls, thermal design) take on critical importance. As such a detailed discussion of reliability from performance at the device level to sub components is included as well as the integrated systems of SSL modules, lamps and luminaires including various failure modes, reliability testing and reliability performance. This book also: Covers the essential reliability theories and practices for current and future development of Solid State Lighting components and systems Provides a systematic overview for not only the state-of-the-art, but also future roadmap and perspectives of Solid State Lighting r...

  20. Remote monitoring of LED lighting system performance

    Science.gov (United States)

    Thotagamuwa, Dinusha R.; Perera, Indika U.; Narendran, Nadarajah

    2016-09-01

    The concept of connected lighting systems using LED lighting for the creation of intelligent buildings is becoming attractive to building owners and managers. In this application, the two most important parameters include power demand and the remaining useful life of the LED fixtures. The first enables energy-efficient buildings and the second helps building managers schedule maintenance services. The failure of an LED lighting system can be parametric (such as lumen depreciation) or catastrophic (such as complete cessation of light). Catastrophic failures in LED lighting systems can create serious consequences in safety critical and emergency applications. Therefore, both failure mechanisms must be considered and the shorter of the two must be used as the failure time. Furthermore, because of significant variation between the useful lives of similar products, it is difficult to accurately predict the life of LED systems. Real-time data gathering and analysis of key operating parameters of LED systems can enable the accurate estimation of the useful life of a lighting system. This paper demonstrates the use of a data-driven method (Euclidean distance) to monitor the performance of an LED lighting system and predict its time to failure.

  1. Aging mathematical model of InGaN/GaN LEDs based on non-radiative recombination

    Science.gov (United States)

    Xu, Linwang; Qian, Keyuan

    2017-08-01

    This paper proposes a new aging mathematical model for InGaN/GaN-based light-emitting diodes (LEDs) based on non-radiative recombination. Light attenuation is an important index of the performance of LEDs, Arrhenius model as the main aging mathematical model of light attenuation is poorly targeted and cannot reflect the physical significance. Based on the physical theory of deep level defects and non-radiation recombination centers, we analyze the aging mechanism of LED chips and then establish the aging mathematical model. Meanwhile, a batch of GaN-based blue LED chips are selected to conduct accelerated life tests with constant current stresses, and the experimental data is obtained to verify the new model. The result shows that compared with the traditional Arrhenius model, the new model has many advantages such as more accurate, strong pertinence and obvious physical meaning.

  2. Automobile Starting and Lighting System Maintenance Training ...

    African Journals Online (AJOL)

    Automobile Starting and Lighting System Maintenance Training Manual for Effective Learning ... Journal Home > Vol 10, No 2 (2015) > ... College Minna and Automobile Supervisors in automobile companies in Minna to establish its reliability.

  3. Towards New Ambient Light Systems: a Close Look at Existing Encodings of Ambient Light Systems

    Directory of Open Access Journals (Sweden)

    Andrii Matviienko

    2015-10-01

    Full Text Available Ambient systems provide information in the periphery of a user’s attention. Their aim is to present information as unobtrusively as possible to avoid interrupting primary tasks (e.g. writing or reading. In recent years, light has been used to create ambient systems to display information. Examples of ambient light systems range from simple notification systems such as displaying messages or calendar event reminders, to more complex systems such as focusing on conveying information regarding health activity tracking. However, for ambient light systems, there is a broad design space that lacks guidelines on when to make use of light displays and how to design them. In this paper we provide a systematic overview of existing ambient light systems over four identified information classes derived from 72 existing ambient light systems. The most prominent encoding parameters among the surveyed ambient light systems are color, brightness, and their combination. By analyzing existing ambient light systems, we provide a first step towards developing guidelines for designing future ambient light systems.

  4. PV led engine characterization lab for standalone light to light systems

    DEFF Research Database (Denmark)

    Thorsteinsson, Sune; Poulsen, Peter Behrensdorff; Lindén, Johannes

    2014-01-01

    PV-powered lighting systems, light-to-light systems (L2L), offer outdoor lighting where it is else where cumbersome to enable lighting. Application of these systems at high latitudes, where the difference in day length between summer and winter is large and the solar energy is low requires smart...

  5. AN OVERVIEW OF VISIBLE LIGHT COMMUNICATION SYSTEMS

    Directory of Open Access Journals (Sweden)

    Taner Cevik

    2015-11-01

    Full Text Available Visible Light Communication (VLC has gained great interest in the last decade due to the rapid developments in Light Emitting Diodes (LEDs fabrication. Efficiency, durability and long life span of LEDs make them a promising residential lighting equipment as well as an alternative cheap and fast data transfer equipment. Appliance of visual light in data communication by means of LEDs has been densely searched in academia. In this paper, we explore the fundamentals and challenges of indoor VLC systems. Basics of optical transmission such as transmitter, receiver, and links are investigated. Moreover, characteristics of channel models in indoor VLC systems are identified and theoretical details about channel modelling are presented in detail.

  6. Multiagent robotic systems' ambient light sensor

    Science.gov (United States)

    Iureva, Radda A.; Maslennikov, Oleg S.; Komarov, Igor I.

    2017-05-01

    Swarm robotics is one of the fastest growing areas of modern technology. Being subclass of multi-agent systems it inherits the main part of scientific-methodological apparatus of construction and functioning of practically useful complexes, which consist of rather autonomous independent agents. Ambient light sensors (ALS) are widely used in robotics. But speaking about swarm robotics, the technology which has great number of specific features and is developing, we can't help mentioning that its important to use sensors on each robot not only in order to help it to get directionally oriented, but also to follow light emitted by robot-chief or to help to find the goal easier. Key words: ambient light sensor, swarm system, multiagent system, robotic system, robotic complexes, simulation modelling

  7. Matrix light and pixel light: optical system architecture and requirements to the light source

    Science.gov (United States)

    Spinger, Benno; Timinger, Andreas L.

    2015-09-01

    Modern Automotive headlamps enable improved functionality for more driving comfort and safety. Matrix or Pixel light headlamps are not restricted to either pure low beam functionality or pure high beam. Light in direction of oncoming traffic is selectively switched of, potential hazard can be marked via an isolated beam and the illumination on the road can even follow a bend. The optical architectures that enable these advanced functionalities are diverse. Electromechanical shutters and lens units moved by electric motors were the first ways to realize these systems. Switching multiple LED light sources is a more elegant and mechanically robust solution. While many basic functionalities can already be realized with a limited number of LEDs, an increasing number of pixels will lead to more driving comfort and better visibility. The required optical system needs not only to generate a desired beam distribution with a high angular dynamic, but also needs to guarantee minimal stray light and cross talk between the different pixels. The direct projection of the LED array via a lens is a simple but not very efficient optical system. We discuss different optical elements for pre-collimating the light with minimal cross talk and improved contrast between neighboring pixels. Depending on the selected optical system, we derive the basic light source requirements: luminance, surface area, contrast, flux and color homogeneity.

  8. Renewable Energy Laboratory for Lighting Systems

    CERN Document Server

    Cristian, Dumitru

    2010-01-01

    Nowadays, the electric lighting is an important part of our lives and also represents a significant part of the electric power consumption. Alternative solutions such as renewable energy applied in this domain are thus welcomed. This paper presents a workstation conceived for the study of photovoltaic solar energy for lighting systems by students of power engineering and civil engineering faculty. The proposed system is realized to study the generated photovoltaic solar energy parameters for lighting systems. For an easier way to study the most relevant parameters virtual instrumentation is implemented. National Instruments LabWindows CVI environment is used as a platform for virtual instrumentation. For future developments remote communication feature intends to be added on which currently remote monitoring of solar photovoltaic energy and electric energy parameters are monitored.

  9. The BaBar Light Pulser System

    Energy Technology Data Exchange (ETDEWEB)

    Clark, P

    2004-03-18

    The BABAR experiment and the PEP-II e{sup +}e{sup -} collider at SLAC in California started taking data in May 1999. The aim of the experiment is to study CP violation in the B meson system. A central part of the BABAR detector is the CsI(Tl) electromagnetic calorimeter. To make precision measurements with a calorimeter in a high luminosity environment requires that the crystals are well calibrated and continually monitored for radiation damage. However, this should not impact the total integrated luminosity. To achieve this goal a fiber-optic light pulser system was designed. The light sources chosen were xenon flash lamps. A novel light distribution method was developed using an array of graded index microlenses. Initial results from performance studies are presented.

  10. Energy Optimization of Road Tunnel Lighting Systems

    Directory of Open Access Journals (Sweden)

    Ferdinando Salata

    2015-07-01

    Full Text Available A road tunnel is an enclosed and covered infrastructure for the vehicular traffic. Its lighting system provides 24 h of artificial sources only, with a higher amount of electric power used during the day. Due to safety reasons, when there is natural lighting outside the tunnel, the lighting levels in the stretches right after the entrance and before the exit must be high, in order to guide the driver’s eye towards the middle of the tunnel where the luminance must guarantee safe driving, avoid any over-dimensioning of the lighting systems, and produce energy savings. Such effects can be reached not only through the technological advances in the field of artificial lighting sources with high luminous efficiency, but also through new materials for road paving characterized by a higher reflection coefficient than other ordinary asphalts. This case study examines different technical scenarios, analyzing and comparing possible energy and economic savings. Traditional solutions are thus compared with scenarios suggesting the solutions previously mentioned. Special asphalts are interesting from an economic point of view, whereas the high costs of LED sources nowadays represent an obstacle for their implementation.

  11. New Directions in Modeling the Lighting Systems

    Directory of Open Access Journals (Sweden)

    P. Fiala

    2004-12-01

    Full Text Available This paper presents information about new directions in the modelingof lighting systems, and an overview of methods for the modeling oflighting systems. The new R-FEM method is described, which is acombination of the Radiosity method and the Finite Elements Method. Thepaper contains modeling results and their verification by experimentalmeasurements and by the Matlab simulation for this R-FEM method.

  12. Switching Of Security Lighting System Using Gsm

    Directory of Open Access Journals (Sweden)

    Bakare, B. I

    2015-01-01

    Full Text Available This paper shows how ATMEGA168 microcontroller can be used to remotely control security lighting via Short Message Service (SMS from a Global System for Mobile Communication (GSM phone anywhere outside the home. A Mobile phone is configured to transmit SMS signal to a home-based GSM modem. The GSM Modem then sends the received SMS to a ATMEGA168 microcontroller. The Microcontroller accesses the received SMS and Changes the State of the appliances if the received signal aggresses with a pre - set code. When this is done, the microcontroller then sends signal to the GSM modem which in turn send back a reply to the mobile phone via SMS. The system utilizes a LCD display with resolution of 96*64 using PCD8544 Driver/Controller to display the ON/OFF state of the lighting device.

  13. Study and Design of LED Lighting Systems

    Directory of Open Access Journals (Sweden)

    Li Cheng

    2013-06-01

    Full Text Available In this study, the optical characteristics, thermal characteristics, electrical characteristics of the LED device are studied. After analysis of the significance of the optical model, we establish the model of the LED light source using optical simulation software to analyze the impact of modeling four factors and law, based on ray tracing model intensity distribution with the manufacturers. On this basis, we expand the LED secondary optical design, namely, increasing of LDE method to the light level. After comparing different forms of non-imaging optical components, combined with the actual situation, the final choice is the system composed of rotating parabolic reflector with LDE. Besides, the reflected changing the relative position of the body and LDE space lead to the normal light intensity of the entire system appearing two peaks, but their causes are different. In addition, the method of combining theoretical analysis and computer simulations to study the distribution of LDE array illumination is utilized. Formula on the illumination distribution in the LDB array to a plane parallel thereto is deduced, which is verified by computer simulation and agrees well with it. A quantitative study of the factors affecting the road surface illuminance distribution is made on the basis of previous study, combined with the actual road lighting works. These factors are: LDE array form, the number of LED, spacing between LDE, LDE interval between the street lamps. The derived entire road illumination distribution formula and the corresponding curve gives a basic method for the analysis of such practical problems related outcomes for the LDE illumination optical system design and research basis.

  14. TPB-coated Light Guides for Liquid Argon TPC Light Detection Systems

    CERN Document Server

    Ignarra, C M

    2013-01-01

    Light detection systems in Liquid Argon Time Projection Chambers (LArTPCs) require the detection of the 128 nm light produced during argon scintillation. Most detectors use Tetraphenyl Butadiene (TPB) to shift the wavelength of the light into a range visible to Photomultiplier Tubes (PMTs). These proceedings summarize characterizations of light-guides coated with a matrix of TPB in UV transmitting acrylic which are more compact than existing LArTPC light collection systems.

  15. Systemic Light Chain Amyloidosis Mimicking Rheumatic Disorders

    Science.gov (United States)

    2016-01-01

    Secondary amyloidosis can complicate chronic inflammatory autoimmune diseases. However, the clinical findings of primary amyloidosis may mimic those of primary rheumatologic disorders. We present the case of a 53-year-old woman who presented with dystrophic nail changes, dry eyes, bilateral carpal tunnel syndrome, Raynaud's phenomenon, and high titer positive nucleolar pattern antinuclear antibody. She was initially misdiagnosed as having Undifferentiated Connective Tissue Disease (UCTD). On further workup, she was eventually diagnosed with lambda light chain systemic amyloidosis by abdominal fat pad biopsy. Her symptoms completely resolved after autologous stem cell transplantation. With this case, we would like to highlight the similarities in the clinical features between light chain amyloidosis and rheumatological disorders. We would also like to emphasize the importance of the prompt recognition of the clinical features of amyloidosis which are crucial to triggering appropriate diagnostic procedures, since early diagnosis is a key to improving outcomes in this disease with an otherwise poor prognosis. PMID:28042297

  16. Systemic Light Chain Amyloidosis Mimicking Rheumatic Disorders

    Directory of Open Access Journals (Sweden)

    Rohit R. Rao

    2016-01-01

    Full Text Available Secondary amyloidosis can complicate chronic inflammatory autoimmune diseases. However, the clinical findings of primary amyloidosis may mimic those of primary rheumatologic disorders. We present the case of a 53-year-old woman who presented with dystrophic nail changes, dry eyes, bilateral carpal tunnel syndrome, Raynaud’s phenomenon, and high titer positive nucleolar pattern antinuclear antibody. She was initially misdiagnosed as having Undifferentiated Connective Tissue Disease (UCTD. On further workup, she was eventually diagnosed with lambda light chain systemic amyloidosis by abdominal fat pad biopsy. Her symptoms completely resolved after autologous stem cell transplantation. With this case, we would like to highlight the similarities in the clinical features between light chain amyloidosis and rheumatological disorders. We would also like to emphasize the importance of the prompt recognition of the clinical features of amyloidosis which are crucial to triggering appropriate diagnostic procedures, since early diagnosis is a key to improving outcomes in this disease with an otherwise poor prognosis.

  17. Modular, Microprocessor-Controlled Flash Lighting System

    Science.gov (United States)

    Kiefer, Dwayne; Gray, Elizabeth; Skupinski, Robert; Stachowicz, Arthur; Birchenough, William

    2006-01-01

    A microprocessor-controlled lighting system generates brief, precisely timed, high-intensity flashes of light for scientific imaging at frame rates up to about 1 kHz. The system includes an array of light-emitting diodes (LEDs) that are driven in synchronism with an externally generated timing signal (for example, a timing signal generated by a video camera). The light output can be varied in peak intensity, pulse duration, pulse delay, and pulse rate, all depending on the timing signal and associated externally generated control signals. The array of LEDs comprises as many as 16 LED panels that can be attached together. Each LED panel is a module consisting of a rectangular subarray of 10 by 20 LEDs of advanced design on a printed-circuit board in a mounting frame with a power/control connector. The LED panels are controlled by an LED control module that contains an AC-to-DC power supply, a control board, and 8 LED-panel driver boards. In prior LED panels, the LEDs are packaged at less than maximum areal densities in bulky metal housings that reduce effective active areas. In contrast, in the present LED panels, the LEDs are packed at maximum areal density so as to afford 100-percent active area and so that when panels are joined side by side to form the array, there are no visible seams between them and the proportion of active area is still 100 percent. Each panel produces an illuminance of .5 x 10( exp 4) lux at a distance of 5.8 in. (approx.1.6 cm). The LEDs are driven according to a pulse-width-modulation control scheme that makes it safe to drive the LEDs beyond their rated steady-state currents in order to generate additional light during short periods. The drive current and the pulse-width modulation for each LED panel can be controlled independently of those of the other 15 panels. The maximum allowable duration of each pulse of drive current is a function of the amount of overdrive, the total time to be spent in overdrive operation, and the limitations

  18. PV LED ENGINE characterization lab for stand alone light-to-light systems

    DEFF Research Database (Denmark)

    Poulsen, Peter Behrensdorff; Thorsteinsson, Sune; Lindén, Johannes

    2015-01-01

    PV-powered lighting systems, light-to-light systems (L2L), offer outdoor lighting where it is elsewhere cumbersome to enable lighting. Application of these systems at high latitudes, where the difference in day length between summer and winter is large and the solar energy is low requires smart d...... are presented. Furthermore, a laboratory has been build to characterize these systems up to 200 Wp from “nose to tail” in great details to support improvement of the systems and to make accurate field performance predictions by the dimensioning tool....

  19. 46 CFR 169.829 - Emergency lighting and power systems.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Emergency lighting and power systems. 169.829 Section... SCHOOL VESSELS Operations Tests, Drills, and Inspections § 169.829 Emergency lighting and power systems. (a) Where fitted, the master shall have the emergency lighting and power systems operated...

  20. A novel amblyopia treatment system based on LED light source

    Science.gov (United States)

    Zhang, Xiaoqing; Chen, Qingshan; Wang, Xiaoling

    2011-05-01

    A novel LED (light emitting diode) light source of five different colors (white, red, green, blue and yellow) is adopted instead of conventional incandescent lamps for an amblyopia treatment system and seven training methods for rectifying amblyopia are incorporated so as for achieving an integrated therapy. The LED light source is designed to provide uniform illumination, adjustable light intensity and alterable colors. Experimental tests indicate that the LED light source operates steadily and fulfills the technical demand of amblyopia treatment.

  1. Freeform microstructure linear light emitter design for a natural light illumination system.

    Science.gov (United States)

    Chen, Bo-Jian; Gao, Bo-Yuan; Ullah, Irfan; Chen, Kuan-Yu; Chou, Chun-Han; Lin, Chia-Min; Chang, Cheng-Ming; Jhan, Kai-Cyuan; Whang, Allen Jong-Woei

    2015-10-01

    The major factors of an illuminative environment are a high rendering index and uniformity. The natural light illumination system (NLIS) is used to guide sunlight for indoor illumination. The NLIS consists of three subsystems: collecting, transmitting, and emitting. Nowadays, a variety of light emitters are available for different illuminative environments. This paper proposes a linear microstructure to diffuse parallel light for indoor illumination. To increase uniformity and promote the illuminative area, the light emitter includes two microstructures for the distribution of light. Finally, the proposed light emitter gives illuminance uniformity and efficiency of 0.55% and 74.18%, respectively.

  2. Advanced optical daylighting systems: light shelves and light pipes

    Energy Technology Data Exchange (ETDEWEB)

    Beltran, L.O.; Lee, E.S.; Selkowitz, S.E.

    1996-05-01

    We present two perimeter daylighting systems that passively redirect beam sunlight further from the window wall using special optical films, an optimized geometry, and a small glazing aperture. The objectives of these systems are (1) to increase daylight illuminance levels at 4.6-9.1 m (15-30 ft) from the window aperture with minimum solar heat gains and (2) to improve the uniformity of the daylighting luminance gradient across the room under variable solar conditions throughout the year. The designs were developed through a series of computer-assisted ray-tracing studies, laser visualization techniques, and photometric measurements and observations using physical scale models. Bi-directional illuminance measurements in combination with analytical routines were then used to simulate daylight performance for any solar position, and were incorporated into the DOE-2.1E building energy analysis computer program to evaluate energy savings. Results show increased daylight levels and an improved luminance gradient throughout the year compared to conventional daylighting systems.

  3. LED based calibration systems of the Baikal-GVD neutrino telescope

    Directory of Open Access Journals (Sweden)

    Avrorin A.D.

    2016-01-01

    Full Text Available Baikal-GVD is a cubic-kilometer scale neutrino telescope, which is currently under construction in Lake Baikal. GVD will consist of an array of optical modules arranged in clusters of strings. The first GVD-cluster has been deployed and put in operation in April 2015. We describe equipment and methods for the calibration of the first GVD-cluster and discuss the accuracy of the calibration procedures.

  4. Non-invasive haemoglobin monitoring by an LED based optical sensor system

    OpenAIRE

    2011-01-01

    peer-reviewed During the perioperative period, which includes the period before surgery (preoperative), during surgery (intraoperative) and after surgery (postoperative), it is essential to measure diagnostic parameters such as: blood oxygen saturation; haemoglobin (Hb) concentration; and pulse rate. The Hb concentration in human blood is an important parameter to evaluate the physiological condition of an individual, as Hb is the oxygen carrying component of red blood cells. By determinin...

  5. A blue-LED-based device for selective photocoagulation of superficial abrasions: theoretical modeling and in vivo validation

    Science.gov (United States)

    Rossi, Francesca; Pini, Roberto; De Siena, Gaetano; Massi, Daniela; Pavone, Francesco S.; Alfieri, Domenico; Cannarozzo, Giovanni

    2010-02-01

    The blue light (~400 nm) emitted by high power Light Emitting Diodes (LED) is selectively absorbed by the haemoglobin content of blood and then converted into heat. This is the basic concept in setting up a compact, low-cost, and easy-to-handle photohaemostasis device for the treatment of superficial skin abrasions. Its main application is in reducing bleeding from superficial capillary vessels during laser induced aesthetic treatments, such as skin resurfacing, thus reducing the treatment time and improving aesthetic results (reduction of scar formation). In this work we firstly present the preliminary modeling study: a Finite Element Model (FEM) of the LED induced photothermal process was set up, in order to estimate the optimal wavelength and treatment time, by studying the temperature dynamics in the tissue. Then, a compact, handheld illumination device has been designed: commercially available high power LEDs emitting in the blue region were mounted in a suitable and ergonomic case. The prototype was tested in the treatment of dorsal excoriations in rats. Thermal effects were monitored by an infrared thermocamera, experimentally evidencing the modest and confined heating effects and confirming the modeling predictions. Objective observations and histopathological analysis performed in a follow-up study showed no adverse reactions and no thermal damage in the treated areas and surrounding tissues. The device was then used in human patients, in order to stop bleeding during Erbium laser skin resurfacing procedure. By inducing LED-based photocoagulation, the overall treatment time was shortened and scar formation was reduced, thus enhancing esthetic effect of the laser procedure.

  6. A LED-based method for monitoring NAD(P)H and FAD fluorescence in cell cultures and brain slices.

    Science.gov (United States)

    Rösner, Jörg; Liotta, Agustin; Schmitz, Dietmar; Heinemann, Uwe; Kovács, Richard

    2013-01-30

    Nicotinamide- and flavine-adenine-dinucleotides (NAD(P)H and FADH₂) are electron carriers involved in cellular energy metabolism and in a multitude of enzymatic processes. As reduced NAD(P)H and oxidised FAD molecules are fluorescent, changes in tissue auto-fluorescence provide valuable information on the cellular redox state and energy metabolism. Since fluorescence excitation, by mercury arc lamps (HBO) is inherently coupled to photo-bleaching and photo-toxicity, microfluorimetric monitoring of energy metabolism might benefit from the replacement of HBO lamps by light emitting diodes (LEDs). Here we describe a LED-based custom-built setup for monitoring NAD(P)H and FAD fluorescence at the level of single cells (HEK293) and of brain slices. We compared NAD(P)H bleaching characteristics with two light sources (HBO lamp and LED) as well as sensitivity and signal to noise ratio of three different detector types (multi-pixel photon counter (MPPC), photomultiplier tube (PMT) and photodiode). LED excitation resulted in reduced photo-bleaching at the same fluorescence output in comparison to excitation with the HBO lamp. Transiently increasing LED power resulted in reversible bleaching of NAD(P)H fluorescence. Recovery kinetics were dependent on metabolic substrates indicating coupling of NAD(P)H fluorescence to metabolism. Electrical stimulation of brain slices induced biphasic redox changes, as indicated by NAD(P)H/FAD fluorescence transients. Increasing the gain of PMT and decreasing the LED power resulted in similar sensitivity as obtained with the MPPC and the photodiode, without worsening the signal to noise ratio. In conclusion, replacement of HBO lamp with LED might improve conventional PMT based microfluorimetry of tissue auto-fluorescence.

  7. Single LED-based device to perform widefield fluorescence imaging and photodynamic therapy

    Science.gov (United States)

    Grecco, Clovis; Buzzá, Hilde H.; Stringasci, Mirian D.; Andrade, Cintia T.; Vollet-Filho, Jose D.; Pratavieira, Sebastião.; Zanchin, Anderson L.; Tuboy, Aparecida M.; Bagnato, Vanderlei S.

    2015-06-01

    Photodynamic therapy (PDT) is a treatment modality that can be indicated for several cancer types and pre-cancer lesions. One of the main applications of PDT is the treatment of superficial skin lesions such as basal cell carcinoma, Bowen's disease and actinic keratosis. Three elements are necessary in PDT, a photosensitizer (PS); light at specific wavelength to be absorbed by the PS, and molecular oxygen. A typical PS used for skin lesion is protoporphyrin IX (PpIX), which is an intrinsic PS; its production is stimulated by a pro-drug, such as 5-aminolevulinic acid (ALA). Before starting a treatment, it is very important to follow up the PpIX production (to ensure that enough PS was produced prior to a PDT application) and, during a PDT session, to monitor its photodegradation (as it is evidence of the photodynamic effect taking place). The aim of this paper is to present a unique device, LINCE (MMOptics - São Carlos, Brazil), that brings together two probes that can, respectively, allow for fluorescence imaging and work as a light source for PDT treatment. The fluorescence probe of the system is optically based on 400 nm LED (light emitting diodes) arrays that allow observing the fluorescence emission over 450 nm. The PDT illumination probe options are constituted of 630 nm LED arrays for small areas and, for large areas, of both 630 nm and 450 nm LED arrays. Joining both functions at the same device makes PDT treatment simpler, properly monitorable and, hence, more clinically feasible. LINCE has been used in almost 1000 PDT treatments of superficial skin lesions in Brazil, with 88.4% of clearance of superficial BCC.

  8. A compact, coherent light source system architecture

    Science.gov (United States)

    Biedron, S. G.; Dattoli, G.; DiPalma, E.; Einstein, J.; Milton, S. V.; Petrillo, V.; Rau, J. V.; Sabia, E.; Spassovsky, I. P.; van der Slot, P. J. M.

    2016-09-01

    Our team has been examining several architectures for short-wavelength, coherent light sources. We are presently exploring the use and role of advanced, high-peak power lasers for both accelerating the electrons and generating a compact light source with the same laser. Our overall goal is to devise light sources that are more accessible by industry and in smaller laboratory settings. Although we cannot and do not want to compete directly with sources such as third-generation light sources or that of national-laboratory-based free-electron lasers, we have several interesting schemes that could bring useful and more coherent, short-wavelength light source to more researchers. Here, we present and discuss several results of recent simulations and our future steps for such dissemination.

  9. Solid-State Spectral Light Source System

    Science.gov (United States)

    Maffione, Robert; Dana, David

    2011-01-01

    A solid-state light source combines an array of light-emitting diodes (LEDs) with advanced electronic control and stabilization over both the spectrum and overall level of the light output. The use of LEDs provides efficient operation over a wide range of wavelengths and power levels, while electronic control permits extremely stable output and dynamic control over the output. In this innovation, LEDs are used instead of incandescent bulbs. Optical feedback and digital control are used to monitor and regulate the output of each LED. Because individual LEDs generate light within narrower ranges of wavelengths than incandescent bulbs, multiple LEDs are combined to provide a broad, continuous spectrum, or to produce light within discrete wavebands that are suitable for specific radiometric sensors.

  10. Visible Light Activated Photocatalytic Water Polishing System Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal targets development of a LED light activated photocatalytic water polishing system that enables reduction of organic impurities (TOC and...

  11. Lighting system with thermal management system having point contact synthetic jets

    Energy Technology Data Exchange (ETDEWEB)

    Arik, Mehmet; Weaver, Stanton Earl; Kuenzler, Glenn Howard; Wolfe, Jr, Charles Franklin; Sharma, Rajdeep

    2016-08-30

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system includes a plurality of synthetic jets. The synthetic jets are arranged within the lighting system such that they are secured at contact points.

  12. Lighting system with thermal management system having point contact synthetic jets

    Energy Technology Data Exchange (ETDEWEB)

    Arik, Mehmet; Weaver, Stanton Earl; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Sharma, Rajdeep

    2016-08-23

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system includes a plurality of synthetic jets. The synthetic jets are arranged within the lighting system such that they are secured at contact points.

  13. Improved TPB-coated Light Guides for Liquid Argon TPC Light Detection Systems

    CERN Document Server

    Moss, Z; Collin, G; Conrad, J M; Jones, B J P; Moon, J; Toups, M; Wongjirad, T

    2014-01-01

    Scintillation light produced in liquid argon (LAr) must be shifted from 128 nm to visible wavelengths in light detection systems used for liquid argon time-projection chambers (LArTPCs). To date, LArTPC light collection systems have employed tetra phenyl butadiene (TPB) coatings on photomultiplier tubes (PMTs) or plates placed in front of the PMTs. Recently, a new approach using TPB-coated light guides was proposed. In this paper, we report on light guides with improved attenuation lengths above 100 cm when measured in air. This is an important step in the development of meter-scale light guides for future LArTPCs. Improvements come from using a new acrylic-based coating, diamond-polished cast UV transmitting acrylic bars, and a hand-dipping technique to coat the bars.

  14. Light unbound nuclear systems beyond the dripline

    Energy Technology Data Exchange (ETDEWEB)

    Aksyutina, Yuliya

    2009-07-01

    Starting from the first observation of the halo phenomenon 20 years ago, more and more neutron-rich light nuclei were observed. The study of unstable nuclear systems beyond the dripline is a relatively new branch of nuclear physics. In the present work, the results of an experiment at GSI (Darmstadt) with relativistic beams of the halo nuclei {sup 8}He, {sup 11}Li and {sup 14}Be with energies of 240, 280 and 305 MeV/nucleon, respectively, impinging on a liquid hydrogen target are discussed. Neutron/proton knockout reactions lead to the formation of unbound systems, followed by their immediate decay. The experimental setup, consisting of the neutron detector LAND, the dipole spectrometer ALADIN and different types of tracking detectors, allows the reconstruction of the momentum vectors of all reaction products measured in coincidence. The properties of unbound nuclei are investigated by reconstructing the relative-energy spectra as well as by studying the angular correlations between the reaction products. The observed systems are {sup 9}He, {sup 10}He, {sup 10}Li, {sup 12}Li and {sup 13}Li. The isotopes {sup 12}Li and {sup 13}Li are observed for the first time. They are produced in the {sup 1}H({sup 14}Be, 2pn){sup 12}Li and {sup 1}H({sup 14}Be, 2p){sup 13}Li knockout reactions. The obtained relative-energy spectrum of {sup 12}Li is described as a single virtual s-state with a scattering length of as = -13.7(1.6) fm. The spectrum of {sup 13}Li is interpreted as a resonance at an energy of E{sub r}=1.47(13) MeV and a width of {gamma} {approx}2 MeV superimposed on a broad correlated background distribution. The isotope {sup 10}Li is observed after one-neutron knockout from the halo nucleus {sup 11}Li. The obtained relative-energy spectrum is described by a low-lying virtual s-state with a scattering length a{sub s}=-22.4(4.8) fm and a p-wave resonance with E{sub r}=0.566(14) MeV and {gamma}=0.548(30) MeV, in agreement with previous experiments. The observation of the

  15. Wearable light management system for light stimulated healing of large area chronic wounds (Conference Presentation)

    Science.gov (United States)

    Kallweit, David; Mayer, Jan; Fricke, Sören; Schnieper, Marc; Ferrini, Rolando

    2016-03-01

    Chronic wounds represent a significant burden to patients, health care professionals, and health care systems, affecting over 40 million patients and creating costs of approximately 40 billion € annually. We will present a medical device for photo-stimulated wound care based on a wearable large area flexible and disposable light management system consisting of a waveguide with incorporated micro- and nanometer scale optical structures for efficient light in-coupling, waveguiding and homogeneous illumination of large area wounds. The working principle of this innovative device is based on the therapeutic effects of visible light to facilitate the self-healing process of chronic wounds. On the one hand, light exposure in the red (656nm) induces growth of keratinocytes and fibroblasts in deeper layers of the skin. On the other hand, blue light (453nm) is known to have antibacterial effects predominately at the surface layers of the skin. In order to be compliant with medical requirements the system will consist of two elements: a disposable wound dressing with embedded flexible optical waveguides for the light management and illumination of the wound area, and a non-disposable compact module containing the light sources, a controller, a rechargeable battery, and a data transmission unit. In particular, we will report on the developed light management system. Finally, as a proof-of-concept, a demonstrator will be presented and its performances will be reported to demonstrate the potential of this innovative device.

  16. Beacon system based on light-emitting diode sources for runways lighting

    Science.gov (United States)

    Montes, Mario González; Vázquez, Daniel; Fernandez-Balbuena, Antonio A.; Bernabeu, Eusebio

    2014-06-01

    New aeronautical ground lighting techniques are becoming increasingly important to ensure the safety and reduce the maintenance costs of the plane's tracks. Until recently, tracks had embedded lighting systems whose sources were based on incandescent lamps. But incandescent lamps have several disadvantages: high energy consumption and frequent breakdowns that result in high maintenance costs (lamp average life-time is ˜1500 operating hours) and the lamp's technology has a lack of new lighting functions, such as signal handling and modification. To solve these problems, the industry has developed systems based on light-emitting diode (LED) technology with improved features: (1) LED lighting consumes one tenth the power, (2) it improves preventive maintenance (an LED's lifetime range is between 25,000 and 100,000 hours), and (3) LED lighting technology can be controlled remotely according to the needs of the track configuration. LEDs have been in use for more than three decades, but only recently, around 2002, have they begun to be used as visual aids, representing the greatest potential change for airport lighting since their inception in the 1920s. Currently, embedded LED systems are not being broadly used due to the specific constraints of the rules and regulations of airports (beacon dimensions, power system technology, etc.). The fundamental requirements applied to embedded lighting systems are to be hosted on a volume where the dimensions are usually critical and also to integrate all the essential components for operation. An embedded architecture that meets the lighting regulations for airport runways is presented. The present work is divided into three main tasks: development of an optical system to optimize lighting according to International Civil Aviation Organization, manufacturing prototype, and model validation.

  17. [Drug release system controlled by near infrared light].

    Science.gov (United States)

    Niidome, Takuro

    2013-01-01

    Gold nanorods have absorption bands in the near-infrared region; in this spectral range, light penetrates deeply into tissues. The absorbed light energy is converted into heat by gold nanorods. This is the so-called photothermal effect. Gold nanorods are therefore expected to act not only as thermal converters for photothermal therapy, but also as controllers for drug-release systems responding to irradiation with near-infrared light. To achieve a controlled-release system that could be triggered by light irradiation, the gold nanorods were modified with double-stranded DNA (dsDNA). When the dsDNA-modified gold nanorods were irradiated with near-infrared light, single-stranded DNA (ssDNA) was released from the gold nanorods because of the photothermal effect. The release of ssDNA was also observed in tumors grown on mice after near-infrared light irradiation. We also proposed a different controlled-release system responding to near-infrared light. Gold nanorods were modified with polyethylene glycol (PEG) through Diels-Alder cycloadducts. When the gold nanorods were irradiated with near-infrared light, the PEG chains were released from the gold nanorods because of the retro Diels-Alder reaction induced by the photothermal effect. Such controlled-release systems triggered by near-infrared light irradiation will be expanded for gold nanorod drug delivery system applications.

  18. CBS - A program for close binary system light curve analysis

    Science.gov (United States)

    Solmi, L.; Galli, M.

    CBS is a new program for binary system light curve analysis, it generates synthetic light curves for a binary system, accounting for eclipses, tidal distortion, limb darkening, gravity darkening and reflection; it is also possible to compute the light contribution and eclipses of an accretion disk. The bolometric light curve is generated, as well as curves for the U,B,V,R,I colour bands. In the following we give a brief description of the first version of the program and show some preliminary results.

  19. High Quantum Efficiency OLED Lighting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Shiang, Joseph [General Electric (GE) Global Research, Fairfield, CT (United States)

    2011-09-30

    The overall goal of the program was to apply improvements in light outcoupling technology to a practical large area plastic luminaire, and thus enable the product vision of an extremely thin form factor high efficiency large area light source. The target substrate was plastic and the baseline device was operating at 35 LPW at the start of the program. The target LPW of the program was a >2x improvement in the LPW efficacy and the overall amount of light to be delivered was relatively high 900 lumens. Despite the extremely difficult challenges associated with scaling up a wet solution process on plastic substrates, the program was able to make substantial progress. A small molecule wet solution process was successfully implemented on plastic substrates with almost no loss in efficiency in transitioning from the laboratory scale glass to large area plastic substrates. By transitioning to a small molecule based process, the LPW entitlement increased from 35 LPW to 60 LPW. A further 10% improvement in outcoupling efficiency was demonstrated via the use of a highly reflecting cathode, which reduced absorptive loss in the OLED device. The calculated potential improvement in some cases is even larger, ~30%, and thus there is considerable room for optimism in improving the net light coupling efficacy, provided absorptive loss mechanisms are eliminated. Further improvements are possible if scattering schemes such as the silver nanowire based hard coat structure are fully developed. The wet coating processes were successfully scaled to large area plastic substrate and resulted in the construction of a 900 lumens luminaire device.

  20. Development of a PET/Cerenkov-light hybrid imaging system

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Seiichi, E-mail: s-yama@met.nagoya-u.ac.jp; Hamamura, Fuka; Kato, Katsuhiko; Ogata, Yoshimune [Radiological and Medical Laboratory Sciences, Nagoya University Graduate School of Medicine, Aichi 461-8673 (Japan); Watabe, Tadashi; Ikeda, Hayato; Kanai, Yasukazu; Hatazawa, Jun [Department of Molecular Imaging in Medicine, Osaka University Graduate School of Medicine, Osaka 565-0871 (Japan); Watabe, Hiroshi [CYRIC, Tohoku University, Miyagi 980-8578 (Japan)

    2014-09-15

    Purpose: Cerenkov-light imaging is a new molecular imaging technology that detects visible photons from high-speed electrons using a high sensitivity optical camera. However, the merit of Cerenkov-light imaging remains unclear. If a PET/Cerenkov-light hybrid imaging system were developed, the merit of Cerenkov-light imaging would be clarified by directly comparing these two imaging modalities. Methods: The authors developed and tested a PET/Cerenkov-light hybrid imaging system that consists of a dual-head PET system, a reflection mirror located above the subject, and a high sensitivity charge coupled device (CCD) camera. The authors installed these systems inside a black box for imaging the Cerenkov-light. The dual-head PET system employed a 1.2 × 1.2 × 10 mm{sup 3} GSO arranged in a 33 × 33 matrix that was optically coupled to a position sensitive photomultiplier tube to form a GSO block detector. The authors arranged two GSO block detectors 10 cm apart and positioned the subject between them. The Cerenkov-light above the subject is reflected by the mirror and changes its direction to the side of the PET system and is imaged by the high sensitivity CCD camera. Results: The dual-head PET system had a spatial resolution of ∼1.2 mm FWHM and sensitivity of ∼0.31% at the center of the FOV. The Cerenkov-light imaging system's spatial resolution was ∼275μm for a {sup 22}Na point source. Using the combined PET/Cerenkov-light hybrid imaging system, the authors successfully obtained fused images from simultaneously acquired images. The image distributions are sometimes different due to the light transmission and absorption in the body of the subject in the Cerenkov-light images. In simultaneous imaging of rat, the authors found that {sup 18}F-FDG accumulation was observed mainly in the Harderian gland on the PET image, while the distribution of Cerenkov-light was observed in the eyes. Conclusions: The authors conclude that their developed PET/Cerenkov-light

  1. Efficient tunable switch from slow light to fast light in quantum opto-electromechanical system

    CERN Document Server

    Akram, M Javed; Saif, Farhan

    2015-01-01

    The control of slow and fast light propagation, in the probe transmission in a single experiment, is a challenging task. This type of control can only be achieved through highly nonlinear interactions and additional interfering pathway(s), which is therefore seldom reported. Here, we devise a scheme in which slow light, and a tunable switch from slow light to fast light can be achieved in the probe transmission based on a hybrid setup, which is composed of an optical cavity with two charged nano mechanical resonators (MRs). The two MRs are electrostatically coupled via tunable Coulomb coupling strength ($g_{c}$) making a quantum opto-electromechanical system (QOEMS). The parameter $g_{c}$ that couples the two MRs can be switched on and off by controlling the bias voltages on the MRs, and acts as a tunable switch that allows the propagation of transmitted probe field as slow light ($g_{c} \

  2. Real-time water and wastewater quality monitoring using LED-based fluorescence spectroscopy

    Science.gov (United States)

    Bridgeman, John; Zakharova, Yulia

    2016-04-01

    In recent years there have been a number of attempts to design and introduce into water management tools that are capable of measuring organic and microbial matter in real time and in situ. This is important, as the delivery of safe water to customers, and the discharge of good quality effluent to rivers are primary concerns to water undertakers. A novel, LED-based portable fluorimeter 'Duo Fluor' has been designed and constructed at the University of Birmingham to monitor the quality of (waste)water continuously and in real time, and its performance has been assessed in a range of environments. To be of use across a range of environments, special attention must be paid to two crucially important characteristics of such instruments, i.e. their sensitivity and robustness. Thus, the objectives of this study were: 1. To compare the performance (in terms of their sensitivity and robustness) of the Duo Fluor and two other commercial fluorescence devices in laboratory conditions. 2. To assess the performance of the Duo Fluor in situ, in real time at a 450,000PE WwTW. Initially, the impact of quinine sulphate (QS), a highly fluorescent alkaloid with high quantum fluorescence yield, on peak T fluorescence in environmental waters was examined for the Duo Fluor and two commercially available, chamber-based fluorimeters, (F1) and (F2). The instruments' responses to three scenarios were assessed: 1. Deionised water (DW) spiked with QS (from 0.05 to 0.4 mg/L); 2. Environmental water (pond water, PW) spiked with QS (from 0.05 to 0.4 mg/L); 3. Different water samples from various environmental source. The results show that the facility to amend gain settings and the suitable choice of gain are crucial to obtaining reliable data on both peaks T and C in a wide range of water types. The Duo Fluor offers both of these advantages whilst commercially available instruments currently do not. The Duo Fluor was subsequently fixed at the final effluent (FE) discharge point of a WwTW and FE

  3. Reduction of background clutter in structured lighting systems

    Science.gov (United States)

    Carlson, Jeffrey J.; Giles, Michael K.; Padilla, Denise D.; Davidson, Jr., Patrick A.; Novick, David K.; Wilson, Christopher W.

    2010-06-22

    Methods for segmenting the reflected light of an illumination source having a characteristic wavelength from background illumination (i.e. clutter) in structured lighting systems can comprise pulsing the light source used to illuminate a scene, pulsing the light source synchronously with the opening of a shutter in an imaging device, estimating the contribution of background clutter by interpolation of images of the scene collected at multiple spectral bands not including the characteristic wavelength and subtracting the estimated background contribution from an image of the scene comprising the wavelength of the light source and, placing a polarizing filter between the imaging device and the scene, where the illumination source can be polarized in the same orientation as the polarizing filter. Apparatus for segmenting the light of an illumination source from background illumination can comprise an illuminator, an image receiver for receiving images of multiple spectral bands, a processor for calculations and interpolations, and a polarizing filter.

  4. THE EFFECTS OF TWO INSTRUMENT LIGHTING SYSTEMS ON DARK ADAPTATION

    Science.gov (United States)

    used. No significant differences were found between the types of lighting systems used. It is concluded that the flight conditions of starlit night sky affect dark adaptation levels to a significant degree.

  5. Detection and Ranging System of Flight Aid Lights

    Institute of Scientific and Technical Information of China (English)

    YU Zhi-jing; WANG Qiang

    2007-01-01

    Dynamic detection based on optics sensors and ranging radars is a new method to detect the luminous intensity of flight aid lights. The optics sensors can get the illumination information of each light, the ranging radar gets the distance information, and then data amalgamation technology is used to compute the luminous intensity of each light. A method to modify the errors of this dynamic detection system is presented. It avoids the accumulation error and measurement carrier's excursion error by using peak value detection based on optics sensors to estimate the accurate position of each light, then to modify the lights' lengthways distance information and transverse position information. The performance of the detection and ranging system is validated by some experiments and shown in pictures.

  6. Boundary conditions on faster-than-light transportation systems

    Science.gov (United States)

    Bennett, Gary L.; Knowles, H. B.

    1993-01-01

    In order to be consistent with current physical theories, any proposal of a faster-than light (FTL) transportation system must satisfy several critical conditions. It must predict the mass, space, and time dimensional changes predicted by relativity physics when velocity falls below the speed of light. It must also not violate causality, and remain consistent with quantum physics in the limit of microscopic systems. It is also essential that the proposal conserve energy.

  7. Restoring Detroit's Street Lighting System

    Energy Technology Data Exchange (ETDEWEB)

    Kinzey, Bruce [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-09-30

    The City of Detroit is in the midst of a comprehensive restoration of its street lighting system that includes transitioning the existing HPS sources to LED. This report provides an objective review of the circumstances surrounding the system restoration, the processes undertaken and decisions made, and the results so far — and contains useful information about issues that arise during large-scale LED street lighting projects.

  8. LED based lightsource for replacement of neon tubes; LED baseret lyskilde til erstatning af lysstofroer

    Energy Technology Data Exchange (ETDEWEB)

    Krogh Jensen, A.

    2005-01-01

    During this project two generations of prototypes of a new type of fluorescent tube that uses light diodes. The technology is expected to result in an electricity consumption reduction of 75 % and a five times longer service life than conventional fluorescent tubes. (BA)

  9. Potential Of Light Pipes System In Malaysian Climate

    Science.gov (United States)

    Abd Kadir, Aslila; Hakim Ismail, Lokman; Kasim, Narimah; Kaamin, Masiri

    2016-11-01

    Light-pipes system are simple structures that allow the transmission of daylight from the outside to the inside of a room. It is a practical application in many buildings where daylight cannot reach due to building design and limited facade to placing windows. Since roof is the element directly exposed to the sunlight, light pipes system could be introduced. This paper examines the illumination levels obtained using light pipes system under Malaysia climate conditions. A light-pipe system that was installed in a test room located in Batu Pahat. Indoor illuminance distributions and concurrent outdoor illuminance were monitored at a 30 minutes interval for 5 days. The results indicated that the amount of daylight penetrated into the building are varied with less than 150lux in the early morning and late evening, and maximum at over 350lux in the noon and early afternoon. The average internal illuminance levels offer by light pipe system met the MS 1525:2007 recommendation for application in Malaysian buildings. These findings indicated that the light pipe system has a potential as a tool for introducing daylight indoors in Malaysia.

  10. Development and Evaluation of a Prototype Barricade Lighting System

    Directory of Open Access Journals (Sweden)

    John Donovan Bullough

    2012-06-01

    Full Text Available Presently in work zones, standard barricade warning lights are used to provide channelizing and warning functions. These yellow flashing lights are presently used for different work zone activities. Concepts for a non-standard barricade lighting system were developed and evaluated: flashing red lights when traffic is stopped or very slow within a work zone, flashing green lights when a work zone is inactive and traffic should proceed normally, expanding yellow lights when drivers should slow down and exercise enhanced caution, and sweeping yellow lights when lane closures require drivers to move to the right or left. Prototype units were designed and fabricated. A survey of driver understanding of these functions indicated that drivers would probably understand all of the functions but that the flashing red and green functions could result in conflicts with other roadway traffic control devices. A field evaluation of the expanding and sweeping functions in mock-up work zones demonstrated that driver comprehension of the lights could be translated to a driving situation. Drivers changed lanes sooner (providing a 40% longer lane change margin in response to the sweeping function than to conventional flashing barricade lights, and subjective ratings about the intended meaning of the tested functions were also positive.

  11. 46 CFR 112.01-10 - Automatic emergency lighting and power system.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Automatic emergency lighting and power system. 112.01-10... EMERGENCY LIGHTING AND POWER SYSTEMS Definitions of Emergency Lighting and Power Systems § 112.01-10 Automatic emergency lighting and power system. An automatic emergency lighting and power system is one...

  12. 46 CFR 112.01-5 - Manual emergency lighting and power system.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Manual emergency lighting and power system. 112.01-5... EMERGENCY LIGHTING AND POWER SYSTEMS Definitions of Emergency Lighting and Power Systems § 112.01-5 Manual emergency lighting and power system. A manual emergency lighting and power system is one in which a...

  13. Metadisorder for designer light in random systems.

    Science.gov (United States)

    Yu, Sunkyu; Piao, Xianji; Hong, Jiho; Park, Namkyoo

    2016-10-01

    Disorder plays a critical role in signal transport by controlling the correlation of a system, as demonstrated in various complex networks. In wave physics, disordered potentials suppress wave transport, because of their localized eigenstates, from the interference between multiple scattering paths. Although the variation of localization with tunable disorder has been intensively studied as a bridge between ordered and disordered media, the general trend of disorder-enhanced localization has remained unchanged, and the existence of complete delocalization in highly disordered potentials has not been explored. We propose the concept of "metadisorder": randomly coupled optical systems in which eigenstates can be engineered to achieve unusual localization. We demonstrate that one of the eigenstates in a randomly coupled system can always be arbitrarily molded, regardless of the degree of disorder, by adjusting the self-energy of each element. Ordered waves with the desired form are then achieved in randomly coupled systems, including plane waves and globally collective resonances. We also devise counterintuitive functionalities in disordered systems, such as "small-world-like" transport from non-Anderson-type localization, phase-conserving disorder, and phase-controlled beam steering.

  14. Color control of a lighting system using RGBW LEDs

    Science.gov (United States)

    Tanaka, Midori; Horiuchi, Takahiko; Tominaga, Shoji

    2011-01-01

    A lighting system is proposed to render objects under a variety of colored illumination. The proposed system is constructed with a LED unit, white diffusion filters, dimmers, and a personal computer as a controller. The LED unit is composed of four kinds of color LED lamps which are 12 red (R), 14 green (G), 12 blue (B) and 10 white (W) colors. The LED lamps have a linear input-output relationship and a larger color gamut than Adobe RGB. Since the lighting system has an independent white light source, white illumination can be produced using the white light source and a mixture of RGB primary sources. Therefore, to determine illumination color we have to solve a mapping problem from 3D color space to 4D space of RGBW digital values. This paper proposes an effective algorithm for determining the digital control signals of the RGBW lights, so that colored light is generated with arbitrary (x, y) chromaticity and luminance value Y. The performance of proposed method is examined in an experiment, where the accuracy of the colored light is evaluated with regard to the CIE color difference.

  15. Benchmarking TPB-coated Light Guides for Liquid Argon TPC Light Detection Systems

    CERN Document Server

    Baptista, B; Chiu, C; Conrad, J M; Ignarra, C M; Jones, B J P; Katori, T; Mufson, S

    2012-01-01

    Scintillation light from liquid argon is produced at 128 nm and thus must be shifted to visible wavelengths in light detection systems used for Liquid Argon Time Projection Chambers (LArTPCs). To date, designs have employed tetraphenyl butadiene (TPB) coatings on photomultiplier tubes (PMTs) or plates placed in front of the PMTs. Recently, a new approach using TPB-coated light guides was proposed. In this paper, we show that the response of lightguides coated with TPB in a UV Transmitting (UVT) acrylic matrix is very similar to that of a coating using a polystyrene (PS) matrix. We obtain a factor of three higher light yield than has been previously reported from lightguides. This paper provides information on the response of the lightguides so that these can be modeled in simulations for future LArTPCs. This paper also identifies areas of R&D for potential improvements in the lightguide response

  16. Design and implementation of organic LED-based displays for signage application

    Science.gov (United States)

    Sharma, Pratibha; Kwok, Harry

    2006-06-01

    Organic light-emitting diodes (OLEDs) have been utilized successfully for various applications such as microdisplays in cell-phones and digital cameras. However, the application of OLEDs for large area signage displays has not yet been established. This paper presents novel design techniques for implementing OLEDs as light sources for signage application. The designs are examined on the basis of signage uniformity, cost and manufacturing complexity. Advantages and limitations of each design are described. It is determined that a trade-off is required to choose a design for implementation. After evaluation and comparison of the designs, the most optimal design is chosen and implemented. Measurement results with the optimal design are described.

  17. Resonating-group calculations in light systems

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Y.C.

    1977-01-01

    The progress made in using the resonating-group method to study the behavior of various systems is reviewed, and the information is discussed which was learned with regard to the importance of the Pauli principle in nuclear problems. 40 references. (JFP)

  18. LIGHT SOURCE: Conceptual design of Hefei Advanced Light Source (HALS) injection system

    Science.gov (United States)

    Zhang, Shan-Cai; Wang, Lin; Feng, Guang-Yao; Wu, Cong-Feng; Li, Wei-Min; Xu, Hong-Liang; Liu, Zu-Ping

    2009-06-01

    The Hefei Advanced Light Source(HALS) is a super low emittance storage ring and has a very short beam life time. In order to run the ring stablely, top-up injection will be necessary. The injection system will greatly affect the quality of beam. This article first gives a physics design of the injecting system. Then the injecting system is tracked under different errors. The responses of storage beam and injecting beam are given in the article.

  19. LIGHT SOURCE: TW Laser system for Thomson scattering X-ray light source at Tsinghua University

    Science.gov (United States)

    Yan, Li-Xm; Du, Ying-Chao; Du, Qiang; Li, Ren-Kai; Hua, Jian-Fei; Huang, Wen-Hui; Tang, Chuan-Xiang

    2009-06-01

    A TW (Tera Watt) laser system based on Ti:sapphire mainly for the Tsinghua Thomson scattering X-ray light source (TTX) is being built. Both UV (ultraviolet) laser pulse for driving the photocathode radio-frequency (RF) gun and the IR (infrared) laser pulse as the electron-beam-scattered-light are provided by the system. Efforts have also been made in laser pulse shaping and laser beam transport to optimize the high-brightness electron beam production by the photocathode RF gun.

  20. Hacking control systems, switching lights off!

    CERN Multimedia

    Computer Security Team

    2013-01-01

    Have you ever heard about “Stuxnet”? “Stuxnet” was a very sophisticated cyber-attack against the Iranian nuclear programme. Like in a spy movie, the attackers infiltrated the uranium enrichment plant at Natanz, arranged for infected USB sticks to be inserted into local PCs, and then the USB viruses did the rest.   Not only did the virus employ four distinct - so far unknown - weaknesses in the Windows operating system, but each weakness could have been sold on the underground market for up to $250,000 each. The virus was targeted to disrupt Iran's uranium production. At first, it scanned the infected PCs for dedicated SCADA (Supervisory Control and Data Acquisition) software from Siemens. Once the virus hit upon that software, it tried to identify any control system components, i.e. so-called PLCs (programmable logic controllers), attached to that PC. If the PLC matched a certain brand (Siemens S7) and configuration, the virus downloaded additi...

  1. Light scattering from macromolecular systems: Molecular crystals and polymers

    Science.gov (United States)

    Bernstein, E. R.

    1981-11-01

    The research objectives were to: (1) characterize phase transitions theoretically and experimentally in molecular crystal systems; (2) use the above understanding gained by light scattering studies and theoretical interpretation to apply to the more complex system of lyotropic liquid crystals; and (3) then apply knowledge gained on the model systems of increasing complexity to polymer liquid crystals and solid polymers as observed by laser light scattering techniques. Systems experimentally and theoretically discussed are: trioxane, triazine, benzil, and chloranil. Studies of lyotropic liquid crystals (sodium decyl sulfate, sodium sulfate, decanol, water) have progressed. The major findings are: a number of phase transitions occur between 20 and 60 C; these transitions evidence strong critical behavior and long correlation times for fluctuations; and liquid crystals can be studied by light scattering. Spectra of solid powders, ribbons, and liquid crystals of PBT and solid PBO were obtained.

  2. A color management system for multi-colored LED lighting

    DEFF Research Database (Denmark)

    Chakrabarti, Maumita; Thorseth, Anders; Jepsen, Jørgen;

    2015-01-01

    A new color control system is described and implemented for a five–color LED light engine, covering a wide white gamut. The system combines a new way of using pre-calibrated look-up tables and a rule-based optimization of chromaticity distance from the Planckian locus with a calibrated color sensor....... The color sensor monitors the chromaticity of the mixed light providing the correction factor for the current driver by using the generated look-up table. The long term stability and accuracy of the system will be experimentally investigated with target tolerance within a circle radius 0.0011 in the uniform...

  3. A color management system for multi-colored LED lighting

    DEFF Research Database (Denmark)

    Chakrabarti, Maumita; Thorseth, Anders; Jepsen, Jørgen

    2015-01-01

    A new color control system is described and implemented for a five–color LED light engine, covering a wide white gamut. The system combines a new way of using pre-calibrated look-up tables and a rule-based optimization of chromaticity distance from the Planckian locus with a calibrated color sensor....... The color sensor monitors the chromaticity of the mixed light providing the correction factor for the current driver by using the generated look-up table. The long term stability and accuracy of the system will be experimentally investigated with target tolerance within a circle radius 0.0011 in the uniform...

  4. Multispectral light metering system for cultural heritage diagnosis and conservation

    Science.gov (United States)

    Miccoli, Matteo; Melis, Marcello

    2013-05-01

    In the world of Cultural Heritage the first concern is all about Conservation of the works of art. A piece of art in bad shape is meant to deteriorate to an irreversible stage. To avoid this, quite often it's needed to go through one or more cycles of restoration to clean and consolidate the various elements of the piece. The very second concern, once the work of art is restored and in good and stable shape, is its fruition. At the end of the day why one should do all that restoration work if nobody then can access and view? Yet viewing and enjoying an artwork means that a visitor would be able to see it at its best, and this means, almost always, to have a good lighting system. Today, both restoration and fruition can greatly benefit of all the available technologies, and achieve very high level quality. The goal of this paper is the development of an exposimetric system suitable to be extremely useful as a tool for the the non invasive analysis, as well as for the lighting design and lighting systems monitoring. Many diagnosis techniques that are used before the restoration stage, require a suitable lighting system to allow to extract from the painting the maximum amount of information through the acquisition of images in the range of visible as well as UV and IR light. A standard exposimeter is for its own nature, sensitive only to the visible light, constrained by the standard photometric sensitivity curve V(lambda). A wide band exposimeter would be, on the other hand, an invaluable tool to get higher precision and to speed up multispectral wide band images acquisition, avoiding time wasting fail and try cycles to record the subject under wide spectrum conditions. The same equipment can be used to monitor the quality of the light in a expo lighting system at, for example, a museum or a gallery. The light hitting a piece of art has to allow the visitor to see and appreciate all the color shades, and to appreciate the contrast of dark and bright areas due only to

  5. Improved Emergency Egress Lighting System for the ISS

    Science.gov (United States)

    Eaton, Leslie L.; Barr, Don A.

    2005-01-01

    Emergency lights provide illumination in corridors, stairwells, ramps, escalators, aisles, and exit passageways during power failures. Safety and visibility are critical during a power outage. If emergency lights fail to operate properly, the building occupants can become disoriented. Four documents in a collection discuss different topics relating to a proposed improved emergency egress lighting system (EELS) for the International Space Station (ISS). While the present EELS is designed around rows of green-light-emitting diodes, the proposed system contains strips of electroluminescent tape using different colors for each egress path. The proposed EELS can be powered by the same battery currently used by the present EELS, but would require an inverter because electroluminescent devices require AC. Electroluminescent devices also require significantly less current and, depending on the color, would emit 3 to 8 times the light of the present EELS. In addition, they could operate for up to 75 hours (versus .20 minutes for the present system). The first document contains a one-page summary of the proposal and an evaluation of technical merit. The second document summarizes the motivation for, and the design of, the proposed EELS. The third document addresses relevant aspects of the measurement of spectral sensitivity and the psychophysics of perception of light. The fourth document presents additional background information and technical specifications for the electroluminescent tapes.

  6. A detection system for energetic light heavy ions

    NARCIS (Netherlands)

    Engelen, C.P.M. van; Jelmersma, R.; Brink, A. van den; Kamermans, R.

    1984-01-01

    A light heavy ion detection system which consists of a gas-filled ionization chamber (IC) connected to a scattering chamber via a time-of-flight (TOF) system has been constructed. The entrance window of the IC has an area of 14 × 40 cm2, the active depth is 115 cm. Filled with CF4 at a pressure of 3

  7. The Study of Full Light Speech Signal Collection System

    Institute of Scientific and Technical Information of China (English)

    JIA Bo; JIN Yaqiu; ZHANG Wei; HU Li; YE Kunzhen

    2001-01-01

    The demodulation character of 3×3 optic fiber couplers is analyzed, and the application in the coherent communication system and speech signal collection is pointed out in the paper. By the experiment, the feasibility of speech signal collection system by the way of the all light is verified.

  8. A color management system for multi-colored LED lighting

    DEFF Research Database (Denmark)

    Chakrabarti, Maumita; Thorseth, Anders; Jepsen, Jørgen;

    2015-01-01

    A new color control system is described and implemented for a five–color LED light engine, covering a wide white gamut. The system combines a new way of using pre-calibrated look-up tables and a rule-based optimization of chromaticity distance from the Planckian locus with a calibrated color sens...

  9. Development of high-performance solar LED lighting system

    KAUST Repository

    Huang, B.J.

    2010-08-01

    The present study developed a high-performance charge/discharge controller for stand-alone solar LED lighting system by incorporating an nMPPO system design, a PWM battery charge control, and a PWM battery discharge control to directly drive the LED. The MPPT controller can then be removed from the stand-alone solar system and the charged capacity of the battery increases 9.7%. For LED driven by PWM current directly from battery, a reliability test for the light decay of LED lamps was performed continuously for 13,200 h. It has shown that the light decay of PWM-driven LED is the same as that of constant-current driven LED. The switching energy loss of the MOSFET in the PWM battery discharge control is less than 1%. Three solar-powered LED lighting systems (18 W, 100 W and 150 W LED) were designed and built. The long-term outdoor field test results have shown that the system performance is satisfactory with the control system developed in the present study. The loss of load probability for the 18 W solar LED system is 14.1% in winter and zero in summer. For the 100 W solar LED system, the loss of load probability is 3.6% in spring. © 2009 Elsevier Ltd. All rights reserved.

  10. Light

    DEFF Research Database (Denmark)

    Prescott, N.B.; Kristensen, Helle Halkjær; Wathes, C.M.

    2004-01-01

    This chapter presents the effect of artificial light environments (light levels, colour, photoperiod and flicker) on the welfare of broilers in terms of vision, behaviour, lameness and mortality......This chapter presents the effect of artificial light environments (light levels, colour, photoperiod and flicker) on the welfare of broilers in terms of vision, behaviour, lameness and mortality...

  11. The unbearable lightness of the extrapyramidal system.

    Science.gov (United States)

    de Oliveira-Souza, Ricardo; Tovar-Moll, Fernanda

    2012-07-01

    The concept of the extrapyramidal system comprises an amalgam of disparate and often conflicting ideas with a tortuous history. To the theoretical neuroscientist or practicing clinician, it promptly evokes semantic associations that are hardly reminiscent of its original meaning. The purpose of this article is to revisit the sources of the extrapyramidal concept and to examine the transformations that it went through from its inception, in the late 1890s, up to the neuroimaging revolution of the 1980s. Our review shows that the use of "extrapyramidal" as a surrogate for the basal ganglia, disorders of movement, or certain manifestations of spastic hemiplegia does not apply to humans; rather, it represents the historical product of the unwarranted translation of results of animal experimentation into the interpretation of clinical findings on human patients, misguided clinico-anatomic deductions, and fanciful phylogenetic notions. We conclude that the extrapyramidal concept is a valid and robust anatomic concept as long as it strictly refers to the collection of descending fibers originating in a few discrete brainstem tegmental motor nuclei that project to the spinal cord.

  12. Lightness computation by the human visual system

    Science.gov (United States)

    Rudd, Michael E.

    2017-05-01

    A model of achromatic color computation by the human visual system is presented, which is shown to account in an exact quantitative way for a large body of appearance matching data collected with simple visual displays. The model equations are closely related to those of the original Retinex model of Land and McCann. However, the present model differs in important ways from Land and McCann's theory in that it invokes additional biological and perceptual mechanisms, including contrast gain control, different inherent neural gains for incremental, and decremental luminance steps, and two types of top-down influence on the perceptual weights applied to local luminance steps in the display: edge classification and spatial integration attentional windowing. Arguments are presented to support the claim that these various visual processes must be instantiated by a particular underlying neural architecture. By pointing to correspondences between the architecture of the model and findings from visual neurophysiology, this paper suggests that edge classification involves a top-down gating of neural edge responses in early visual cortex (cortical areas V1 and/or V2) while spatial integration windowing occurs in cortical area V4 or beyond.

  13. A green-light inducible lytic system for cyanobacterial cells.

    Science.gov (United States)

    Miyake, Kotone; Abe, Koichi; Ferri, Stefano; Nakajima, Mitsuharu; Nakamura, Mayumi; Yoshida, Wataru; Kojima, Katsuhiro; Ikebukuro, Kazunori; Sode, Koji

    2014-01-01

    Cyanobacteria are an attractive candidate for the production of biofuel because of their ability to capture carbon dioxide by photosynthesis and grow on non-arable land. However, because huge quantities of water are required for cultivation, strict water management is one of the greatest issues in algae- and cyanobacteria-based biofuel production. In this study, we aim to construct a lytic cyanobacterium that can be regulated by a physical signal (green-light illumination) for future use in the recovery of biofuel related compounds. We introduced T4 bacteriophage-derived lysis genes encoding holin and endolysin under the control of the green-light regulated cpcG2 promoter in Synechocystis sp. PCC 6803. When cells harboring the lysis genes were illuminated with both red and green light, we observed a considerable decrease in growth rate, a significant increase in cellular phycocyanin released in the medium, and a considerable fraction of dead cells. These effects were not observed when these cells were illuminated with only red light, or when cells not containing the lysis genes were grown under either red light or red and green light. These results indicate that our constructed green-light inducible lytic system was clearly induced by green-light illumination, resulting in lytic cells that released intracellular phycocyanin into the culture supernatant. This property suggests a future possibility to construct photosynthetic genetically modified organisms that are unable to survive under sunlight exposure. Expression of the self-lysis system with green-light illumination was also found to greatly increase the fragility of the cell membrane, as determined by subjecting the induced cells to detergent, osmotic-shock, and freeze-thaw treatments. A green-light inducible lytic system was constructed in Synechocystis sp. PCC 6803. The engineered lytic cyanobacterial cells should be beneficial for the recovery of biofuels and related compounds from cells with minimal effort

  14. Light and immune systems: activation of immunological activities

    Science.gov (United States)

    Huang, Zheng; Liu, Hong; Chen, Wei R.

    2006-02-01

    Light has been used to treat diseases for hundreds of years. Convenient and powerful light sources such as lasers make photomedicine a major branch in diseases treatment and detection. Originally, light was often used for local treatment, using photomechanical, photochemical, photothermal reactions and photomodulation as the major mechanisms. More and more investigators have become interested in the systemic effects of light, particularly in its effects on immune systems. Much work has been done to activate and/or enhance the host immune system to combat cancer, either using light as a direct tool or as an adjuvant method. Light has long been used for assisting disease detection and diagnosis. Advances in light technology have made photo-diagnostics ever more precise spatially and temporally. Many techniques facilitate observation of bio-molecule interactions and other biological processes at the cellular level, hence providing opportunities to detect and monitor immune activities. This manuscript will review recent photo-immunological research in treatment of cancer. The recent development of combination therapies involving lasers will be presented. Specifically, the results of cancer treatment using laser photothermal interaction, either with or without additional immunological stimulation will be discussed. The immunological effects of photodynamic therapy (PDT), and of its combination with immunotherapy in cancer treatment will also be discussed. Much interest has been recently concentrated in the immunological responses after laser treatment. Such responses at cellular and molecular levels will be discussed. The effect of these treatment modalities on the distant metastases also showed promise of light induced antitumor immunity. The combination therapy and induced immunological responses appear to be the key for long-term control of tumors.

  15. CMOS indoor light energy harvesting system for wireless sensing applications

    CERN Document Server

    Ferreira Carvalho, Carlos Manuel

    2016-01-01

    This book discusses in detail the CMOS implementation of energy harvesting.  The authors describe an integrated, indoor light energy harvesting system, based on a controller circuit that dynamically and automatically adjusts its operation to meet the actual light circumstances of the environment where the system is placed.  The system is intended to power a sensor node, enabling an autonomous wireless sensor network (WSN). Although designed to cope with indoor light levels, the system is also able to work with higher levels, making it an all-round light energy harvesting system.  The discussion includes experimental data obtained from an integrated manufactured prototype, which in conjunction with a photovoltaic (PV) cell, serves as a proof of concept of the desired energy harvesting system.  ·         Discusses several energy sources which can be used to power energy harvesting systems and includes an overview of PV cell technologies  ·         Includes an introduction to voltage step-...

  16. Synergetic Effect between Lighting Efficiency Enhancement and Building Energy Reduction Using Alternative Thermal Operating System of Indoor LED Lighting

    National Research Council Canada - National Science Library

    Byung-Lip Ahn; Ji-Woo Park; Seunghwan Yoo; Jonghun Kim; Hakgeun Jeong; Seung-Bok Leigh; Cheol-Yong Jang

    2015-01-01

      We investigated the synergetic effect between light-emitting diode (LED) lighting efficiency and building energy savings in heating and cooling using an alternative thermal operating system (ATOS...

  17. Scintillation Light Detection System in LArIAT

    Energy Technology Data Exchange (ETDEWEB)

    Kryczynski, Pawel [Cracow, INP

    2016-02-29

    The LArIAT experiment is currently taking data at Fermilab using a Liquid Argon TPC, with the aim of studying particle interactions and characterizing detector response for neutrino detectors using argon. In parallel, it serves as a test-bench to develop and evaluate the performance of the simulation, reconstruction, and analysis software used in LAr neutrino experiments. LArIAT also takes advantage of the scintillating capabilities of liquid argon and will evaluate the feasibility of using the light signal to determine calorimetric information and particle identification. To test this possibility, a scintillation light detection system consisting of high Quantum Efficiency (QE) PMT and Silicon Photomultiplier (SiPM) devices is installed in the cryostat, viewing the interior of the TPC. Light collection efficiency is maximized by means of lining the walls with reflector foils covered by a wavelength shifter layer. Collecting the light reflected at the boundaries of the active volume greatly improves also the uniformity of the light yield. Presented here are initial results of the LArIAT light detection system calibration together with the preliminary results of the dedicated simulation and its application in future LAr TPC experiments

  18. The Advanced Light Source (ALS) Radiation Safety System. Revised

    Energy Technology Data Exchange (ETDEWEB)

    Ritchie, A.L.; Oldfather, D.E.; Lindner, A.F.

    1993-08-01

    The Advanced Light Source (ALS) at the Lawrence Berkeley Laboratory (LBL) is a 1.5 Gev synchrotron light source facility consisting of a 120 kev electron gun, 50 Mev linear accelerator, 1.5 Gev booster synchrotron, 200 meter circumference electron storage ring, and many photon beamline transport systems for research. Figure 1. ALS floor plan. Pairs of neutron and gamma radiation monitors are shown as dots numbered from 1 to 12. The Radiation Safety System for the ALS has been designed and built with a primary goal of providing protection against inadvertent personnel exposure to gamma and neutron radiation and, secondarily, to enhance the electrical safety of select magnet power supplies.

  19. Restoring Detroit's Street Lighting System

    Energy Technology Data Exchange (ETDEWEB)

    Kinzey, Bruce R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2015-10-21

    The City of Detroit is undertaking a comprehensive restoration of its street lighting system that includes transitioning the existing high-pressure sodium (HPS) sources to light-emitting diode (LED). Detroit’s well-publicized financial troubles over the last several years have added many hurdles and constraints to this process. Strategies to overcome these issues have largely been successful, but have also brought some mixed results. This document provides an objective review of the circumstances surrounding the system restoration, the processes undertaken and decisions made, and the results so far.

  20. An All Fiber White Light Interferometric Absolute Temperature Measurement System

    Directory of Open Access Journals (Sweden)

    Jeonggon Harrison Kim

    2008-11-01

    Full Text Available Recently the author of this article proposed a new signal processing algorithm for an all fiber white light interferometer. In this article, an all fiber white light interferometric absolute temperature measurement system is presented using the previously proposed signal processing algorithm. Stability and absolute temperature measurement were demonstrated. These two tests demonstrated the feasibility of absolute temperature measurement with an accuracy of 0.015 fringe and 0.0005 fringe, respectively. A hysteresis test from 373K to 873K was also presented. Finally, robustness of the sensor system towards laser diode temperature drift, AFMZI temperature drift and PZT non-linearity was demonstrated.

  1. A novel dual-LED based long-path DOAS instrument for the measurement of aromatic hydrocarbons

    Science.gov (United States)

    Stutz, Jochen; Hurlock, Stephen C.; Colosimo, Santo F.; Tsai, Catalina; Cheung, Ross; Festa, James; Pikelnaya, Olga; Alvarez, Sergio; Flynn, James H.; Erickson, Matthew H.; Olaguer, Eduardo P.

    2016-12-01

    Aromatic hydrocarbons are well known air toxics which are regulated by the US EPA and other air quality agencies. Accurate, long-term monitoring of these compounds at low part-per-billion levels, as well as identifying emission point sources is therefore crucial to protect human health in neighborhoods near large emission sources. Here we present a new long-path differential optical absorption spectroscopy (LP-DOAS) instrument specifically designed to monitor aromatic hydrocarbons. The system is based on a novel dual - light emitting diode (LED) light source, which eliminates the requirement to suppress spectrometer stray light. This light source, together with a high stability fiber-based sending/receiving telescope, allows the measurement of aromatic hydrocarbons on once-folded absorptions paths of 200-1200 m length. The new instrument shows very good agreement with simultaneous in-situ measurements if inhomogeneities of the trace gas spatial distributions are considered. The new instrument performed well during a three-month field test as an automated fence-line monitor at a refinery, successfully distinguishing upwind background levels of ∼1 ppb from emissions reflected in elevated mixing ratios of 3-4 ppb. A two-dimensional measurement network based on two identical LP-DOAS instruments operating on seven crossed light paths was operated successfully in Houston, TX. Qualitative and quantitative analysis of two events with toluene and xylene plumes demonstrate how this setup can be used to derive the spatial distribution of aromatic hydrocarbons, and identify point sources.

  2. An LED-based fluorometer for chlorophyll quantification in the laboratory and in the field.

    Science.gov (United States)

    Lamb, Jacob J; Eaton-Rye, Julian J; Hohmann-Marriott, Martin F

    2012-10-01

    The chlorophyll content is an important experimental parameter in agronomy and plant biology research. In this report, we explore the feasibility of determining total concentration of extracts containing chlorophyll a and chlorophyll b by chlorophyll fluorescence. We found that an excitation at 457 nm results in the same integrated fluorescence emission for a molecule of chlorophyll a and a molecule of chlorophyll b. The fluorescence yield induced by 457 nm is therefore proportional to total molar chlorophyll concentration. Based on this observation, we designed an instrument to determine total chlorophyll concentrations. A single light emitting diode (LED) is used to excite chlorophyll extracts. After passing through a long-pass filter, the fluorescence emission is assessed by a photodiode. We demonstrate that this instrument facilitates the determination of total chlorophyll concentrations. We further extended the functionality of the instrument by including LEDs emitting at 435 and 470 nm wavelengths, thereby preferentially exciting chlorophyll a and chlorophyll b. This instrument can be used to determine chlorophyll a and chlorophyll b concentrations in a variety of organisms containing different ratios of chlorophylls. Monte-Carlo simulations are in agreement with experimental data such that a precise determination of chlorophyll concentrations in carotenoid-containing biological samples containing a concentration of less than 5 nmol/mL total chlorophyll can be achieved.

  3. LED lamps in shipboard lighting systems: Aspects of electromagnetic compatibility

    Directory of Open Access Journals (Sweden)

    Beley V. F.

    2016-12-01

    Full Text Available Trends in the development of different types of light sources and their energy characteristics have been described in the paper. Analysis of regulatory documents has been given. The results of experimental studies of a number of modern LED lamps have been described. Investigation has been made for a number of LED lamps produced by Philips, Xavax and Melitec. The experimental data have been obtained with the complex of devices: the dual-channel oscilloscope (GDS-71042, the power quality analyzer (Fluke-434 and the multi-function device EcoLight-01 (light-, pulse- and luminance meter. It has been shown that operation of LED lamps is characterized by emission of higher current harmonics and reactive power consumption, which depends on the type and design of the lamp driver. It has been found that the value of luminance created by LED lamps in case of acceptable (for ships prolonged deviation of voltage (–10 % is reduced by 3 %; in case of permissible short-term voltage deviation (–20 % luminance is reduced by 7 %. For incandescent lamps this indicator is characterized by a decrease in luminance by 40 % and 60 %, respectively. Despite the low sensitivity to voltage changes (in comparison with other types of lamps, the operation of LED lamps is also associated with the appearance of flicker. Absence of limitations for fluctuations of the light flux in shipboard lighting systems and imperfection of methods for determining the flicker make it difficult to ensure electromagnetic compatibility of LED lamps. Therefore due to reliability, environmental friendliness, energy efficiency and lumen maintenance LED lamps have prospects for introduction into shipboard lighting systems. However, to ensure electromagnetic compatibility of LED lighting systems it is necessary to conduct a detailed study of energy characteristics of LED lamps and to develop appropriate regulatory requirements and technical solutions.

  4. Design and optimization of a light-emitting diode projection micro-stereolithography three-dimensional manufacturing system.

    Science.gov (United States)

    Zheng, Xiaoyu; Deotte, Joshua; Alonso, Matthew P; Farquar, George R; Weisgraber, Todd H; Gemberling, Steven; Lee, Howon; Fang, Nicholas; Spadaccini, Christopher M

    2012-12-01

    The rapid manufacture of complex three-dimensional micro-scale components has eluded researchers for decades. Several additive manufacturing options have been limited by either speed or the ability to fabricate true three-dimensional structures. Projection micro-stereolithography (PμSL) is a low cost, high throughput additive fabrication technique capable of generating three-dimensional microstructures in a bottom-up, layer by layer fashion. The PμSL system is reliable and capable of manufacturing a variety of highly complex, three-dimensional structures from micro- to meso-scales with micro-scale architecture and submicron precision. Our PμSL system utilizes a reconfigurable digital mask and a 395 nm light-emitting diode (LED) array to polymerize a liquid monomer in a layer-by-layer manufacturing process. This paper discusses the critical process parameters that influence polymerization depth and structure quality. Experimental characterization and performance of the LED-based PμSL system for fabricating highly complex three-dimensional structures for a large range of applications is presented.

  5. Adaptive Color Calibration Based One-Shot Structured Light System

    Directory of Open Access Journals (Sweden)

    Jie Yuan

    2012-08-01

    Full Text Available In one-shot color structured light systems, the color of stripe patterns are typically distorted with respect to color crosstalk, ambient light and the albedo of the scanned objects, leading to mismatch in the correspondence of color stripes between the projected and captured images. In this paper, an adaptive color calibration and Discrete Trend Transform algorithm are presented to achieve high-resolution 3D reconstructions. The adaptive color calibration, according to the relative albedo in RGB channels, can improve the accuracy of labeling stripe by alleviating the effect of albedo and ambient light while decoding the color. Furthermore, the Discrete Trend Transform in the M channel makes the color calibration an effective method for detecting weak stripes due to the uneven surfaces or reflectance characteristics of the scanned objects. With this approach, the presented system is suitable for scanning moving objects and generating high-resolution 3D reconstructions without the need of dark laboratory environments.

  6. Adaptive color calibration based one-shot structured light system.

    Science.gov (United States)

    Zhou, Yu; Zhao, Dongwei; Yu, Yao; Yuan, Jie; Du, Sidan

    2012-01-01

    In one-shot color structured light systems, the color of stripe patterns are typically distorted with respect to color crosstalk, ambient light and the albedo of the scanned objects, leading to mismatch in the correspondence of color stripes between the projected and captured images. In this paper, an adaptive color calibration and Discrete Trend Transform algorithm are presented to achieve high-resolution 3D reconstructions. The adaptive color calibration, according to the relative albedo in RGB channels, can improve the accuracy of labeling stripe by alleviating the effect of albedo and ambient light while decoding the color. Furthermore, the Discrete Trend Transform in the M channel makes the color calibration an effective method for detecting weak stripes due to the uneven surfaces or reflectance characteristics of the scanned objects. With this approach, the presented system is suitable for scanning moving objects and generating high-resolution 3D reconstructions without the need of dark laboratory environments.

  7. Design and development of LED-based irregular leather area measuring machine

    Science.gov (United States)

    Adil, Rehan; Khan, Sarah Jamal

    2012-01-01

    Using optical sensor array, a precision motion control system in a conveyer follows the irregular shaped leather sheet to measure its surface area. In operation, irregular shaped leather sheet passes on conveyer belt and optical sensor array detects the leather sheet edge. In this way outside curvature of the leather sheet is detected and is then feed to the controller to measure its approximate area. Such system can measure irregular shapes, by neglecting rounded corners, ellipses etc. To minimize the error in calculating surface area of irregular curve to the above mentioned system, the motion control system only requires the footprint of the optical sensor to be small and the distance between the sensors is to be minimized. In the proposed technique surface area measurement of irregular shaped leather sheet is done by defining velocity and detecting position of the move. The motion controller takes the information and creates the necessary edge profile on point-to-point bases. As a result irregular shape of leather sheet is mapped and is then feed to the controller to calculate surface area.

  8. IMPLEMENTATION PHOTOVOLTAIC PANELS IN LIGHTING SYSTEM OF A SHIP

    Directory of Open Access Journals (Sweden)

    FLORENTIU DELIU

    2016-06-01

    Full Text Available The possibility of using other sources of electricity than conventional one, on board vessels, i s a highly actual subject. In this respect, this paper presents a simulation on the development of a proper photovoltaic panels configuration used for the lighting system of the ship, with 42kW installed average power.

  9. Light communication systems. Citations from the NTIS data base

    Science.gov (United States)

    Reed, W. E.

    1980-09-01

    The design, performance, and application of laser, infrared, and visual communication systems are covered in the cited research reports. Transmission and equipment studies for space, atmospheric, and underwater light communication are presented. Topics covered include lasers, fiber optics, signal processing, transmission links, and data transmission. This updated bibliography contains 87 citations, 59 of which are new entries to the previous edition.

  10. Solar concentrator with integrated tracking and light delivery system with summation

    Energy Technology Data Exchange (ETDEWEB)

    Maxey, Lonnie Curt

    2015-05-05

    A solar light distribution system includes a solar light concentrator that is affixed externally to a light transfer tube. Solar light waves are processed by the concentrator into a collimated beam of light, which is then transferred through a light receiving port and into the light transfer tube. A reflector redirects the collimated beam of light through the tube to a light distribution port. The interior surface of the light transfer tube is highly reflective so that the light transfers through the tube with minimal losses. An interchangeable luminaire is attached to the light distribution port and provides light inside of a structure. A sun tracking device rotates the concentrator and the light transfer tube to optimize the receiving of solar light by the concentrator throughout the day. The system provides interior lighting that uses only renewable energy sources, and releases no carbon dioxide emissions into the atmosphere.

  11. Solar concentrator with integrated tracking and light delivery system with collimation

    Energy Technology Data Exchange (ETDEWEB)

    Maxey, Lonnie Curt

    2015-06-09

    A solar light distribution system includes a solar light concentrator that is affixed externally to a light transfer tube. Solar light waves are processed by the concentrator into a collimated beam of light, which is then transferred through a light receiving port and into the light transfer tube. A reflector directs the collimated beam of light through the tube to a light distribution port. The interior surface of the light transfer tube is highly reflective so that the light transfers through the tube with minimal losses. An interchangeable luminaire is attached to the light distribution port and distributes light inside of a structure. A sun tracking device rotates the concentrator and the light transfer tube to optimize the receiving of solar light by the concentrator throughout the day. The system provides interior lighting, uses only renewable energy sources, and releases no carbon dioxide emissions into the atmosphere.

  12. Timing growth and development of Campanula by daily light integral and supplemental light level in a cost-efficient light control system

    DEFF Research Database (Denmark)

    Kjær, Katrine Heinsvig; Ottosen, Carl-Otto; Jørgensen, Bo Nørregaard

    2012-01-01

    light control system (DynaLight desktop) automatically defines the most cost-efficient use of supplemental light based on predefined setpoints for daily photosynthesis integral (DPI), forecasted solar irradiance and the market price on electricity. It saves energy in high-cost periods of electricity...... mol m−2 s−1). We found that differences in supplemental light levels, daily light hours or DLI had no effect on leaf area expansion and stem elongation, but there was a linear relation between dry matter accumulation and cumulative light integral (CLI) in both species, and a linear relation between...

  13. SETI via Leakage from Light Sails in Exoplanetary Systems

    Science.gov (United States)

    Guillochon, James; Loeb, Abraham

    2015-10-01

    The primary challenge of rocket propulsion is the burden of needing to accelerate the spacecraft’s own fuel, resulting in only a logarithmic gain in maximum speed as propellant is added to the spacecraft. Light sails offer an attractive alternative in which fuel is not carried by the spacecraft, with acceleration being provided by an external source of light. By artificially illuminating the spacecraft with beamed radiation, speeds are only limited by the area of the sail, heat resistance of its material, and power use of the accelerating apparatus. In this paper, we show that leakage from a light sail propulsion apparatus in operation around a solar system analogue would be detectable. To demonstrate this, we model the launch and arrival of a microwave beam-driven light sail constructed for transit between planets in orbit around a single star, and find an optimal beam frequency on the order of tens of GHz. Leakage from these beams yields transients with flux densities of Jy and durations of tens of seconds at 100 pc. Because most travel within a planetary system would be conducted between the habitable worlds within that system, multiply transiting exoplanetary systems offer the greatest chance of detection, especially when the planets are in projected conjunction as viewed from Earth. If interplanetary travel via beam-driven light sails is commonly employed in our galaxy, this activity could be revealed by radio follow-up of nearby transiting exoplanetary systems. The expected signal properties define a new strategy in the search for extraterrestrial intelligence (SETI).

  14. SETI VIA LEAKAGE FROM LIGHT SAILS IN EXOPLANETARY SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    Guillochon, James; Loeb, Abraham, E-mail: jguillochon@cfa.harvard.edu, E-mail: aloeb@cfa.harvard.edu [Harvard-Smithsonian Center for Astrophysics, The Institute for Theory and Computation, 60 Garden Street, Cambridge, MA 02138 (United States)

    2015-10-01

    The primary challenge of rocket propulsion is the burden of needing to accelerate the spacecraft’s own fuel, resulting in only a logarithmic gain in maximum speed as propellant is added to the spacecraft. Light sails offer an attractive alternative in which fuel is not carried by the spacecraft, with acceleration being provided by an external source of light. By artificially illuminating the spacecraft with beamed radiation, speeds are only limited by the area of the sail, heat resistance of its material, and power use of the accelerating apparatus. In this paper, we show that leakage from a light sail propulsion apparatus in operation around a solar system analogue would be detectable. To demonstrate this, we model the launch and arrival of a microwave beam-driven light sail constructed for transit between planets in orbit around a single star, and find an optimal beam frequency on the order of tens of GHz. Leakage from these beams yields transients with flux densities of Jy and durations of tens of seconds at 100 pc. Because most travel within a planetary system would be conducted between the habitable worlds within that system, multiply transiting exoplanetary systems offer the greatest chance of detection, especially when the planets are in projected conjunction as viewed from Earth. If interplanetary travel via beam-driven light sails is commonly employed in our galaxy, this activity could be revealed by radio follow-up of nearby transiting exoplanetary systems. The expected signal properties define a new strategy in the search for extraterrestrial intelligence (SETI)

  15. Automatic control systems of daylighting and artificial lighting; Saiko shomei setsubi no seigyo system

    Energy Technology Data Exchange (ETDEWEB)

    Saito, M. [Obayashi Corp., Tokyo (Japan)

    1997-06-05

    Means for controlling illumination include a blind for adjusting the light coming directly from the sun, system for maintaining environmental comfort by controlling light-modulating glass and the like, labor-saving system incorporating a control center governing multiple buildings in the vicinity, and system intended for improved energy efficiency. Energy saving efforts include an occupancy sensor control for the automatic turn-on/off of lighting by detecting the presence or absence of people in a chamber, optimum lighting control using sensors for adjusting illumination to the designed level, time-scheduled control for the turning-on/off of lighting according to the time of the day, daylight utilizing control for adjusting artificial lighting according to the amount of incident daylight, guidance light control system for turning on guidance lights upon sensing a decrease in incident daylight. Other than these, there are controls of lighting for performance and demonstration. Examples of practical application include the system adopted by Museum of Contemporary Art, Tokyo, for keeping incident light homogeneous, and the optimum illumination control and daylight utilizing control of Research & Development Center, The Tokyo Electric Power Co., Ltd. 8 refs., 10 figs.

  16. High dynamic grayscale lithography with an LED-based micro-image stepper

    Science.gov (United States)

    Eckstein, Hans-Christoph; Zeitner, Uwe D.; Leitel, Robert; Stumpf, Marko; Schleicher, Philipp; Bräuer, Andreas; Tünnermann, Andreas

    2016-03-01

    We developed a novel LED projection based direct write grayscale lithography system for the generation of optical surface profiles such as micro-lenses, diffractive elements, diffusors, and micro freeforms. The image formation is realized by a LCoS micro-display which is illuminated by a 405 nm UV High Power LED. The image on the display can be demagnified from factors 5x to 100x with an exchangeable lens. By controlling exposure time and LED power, the presented technique enables a highly dynamic dosage control for the exposure of h-line sensitive photo resist. In addition, the LCoS micro-display allows for an intensity control within the micro-image which is particularly advantageous to eliminate surface profile errors from stitching and limited homogeneity from LED illumination. Together with an accurate calibration of the resist response this leads to a superior low surface error of realized profiles below area of 500 × 500 mm2 with a positioning accuracy of 80°. Another benefit of the approach is a patterning speed up to 100 cm2/h, which allows fabricating large-scale optics and microstructures in an acceptable time. We present the setup and show examples of micro-structures to demonstrate the performance of the system, namely a refractive freeform array, where the RMS surface deviation does not exceed 0.2% of the total structure depth of 75 μm. Furthermore, we show that this exposure tool is suitable to generate diffractive optical elements as well as freeform optics and arrays with a high aspect ratio and structure depth showing a superior optical performance. Lastly we demonstrate a multi-level diffraction grating on a curved substrate.

  17. Development of Vehicle Lighting System Using LED Application

    Directory of Open Access Journals (Sweden)

    Asmarashid Ponniran

    2011-12-01

    Full Text Available A Light Emitting Diode (LED is a semiconductor device which converts electricity into light. LEDs are preferred over incandescent lamps because of their long life and their availability in various colors and brightness levels. The aim of this paper is to present the development of vehicle lighting system using LED application. In this system, high power LEDs type is chosen as automobile headlight model and controller circuit using microcontroller is considered. The LEDs are driven using buck converter circuit with appropriate Pulse Width Modulation (PWM signal whereby the PWM signals are generated by microcontroller. The system is divided into 2 modes of operation, manual and automatic. The automatic mode of operation will be operating when the LDR senses the level of light brightness whereby the level of brightness is proportion to duty cycle of PWM. Meanwhile, for the manual mode of operation, 3 switches which are SW2 with 20% duty cycle, SW3 with 40% duty cycle and SW3 with 80% duty cycle are developed. The result shows that the maximum brightness of LED is about 127.6 Lumen at 80% of duty cycle for manual operation mode. Besides, by varying theduty cycle of PWM signal for both modes of operation, manual and automatic, LED brightness can be controlled.

  18. A new dump system design for stray light reduction of Thomson scattering diagnostic system on EAST

    Science.gov (United States)

    Xiao, Shumei; Zang, Qing; Han, Xiaofeng; Wang, Tengfei; Yu, Jin; Zhao, Junyu

    2016-07-01

    Thomson scattering (TS) diagnostic is an important diagnostic for measuring electron temperature and density during plasma discharge. However, the measurement of Thomson scattering signal is disturbed by the stray light easily. The stray light sources in the Experimental Advanced Superconducting Tokamak (EAST) TS diagnostic system were analyzed by a simulation model of the diagnostic system, and simulation results show that the dump system is the primary stray light source. Based on the optics theory and the simulation analysis, a novel dump system including an improved beam trap was proposed and installed. The measurement results indicate that the new dump system can reduce more than 60% of the stray light for the diagnostic system, and the influence of stray light on the error of measured density decreases.

  19. A new dump system design for stray light reduction of Thomson scattering diagnostic system on EAST.

    Science.gov (United States)

    Xiao, Shumei; Zang, Qing; Han, Xiaofeng; Wang, Tengfei; Yu, Jin; Zhao, Junyu

    2016-07-01

    Thomson scattering (TS) diagnostic is an important diagnostic for measuring electron temperature and density during plasma discharge. However, the measurement of Thomson scattering signal is disturbed by the stray light easily. The stray light sources in the Experimental Advanced Superconducting Tokamak (EAST) TS diagnostic system were analyzed by a simulation model of the diagnostic system, and simulation results show that the dump system is the primary stray light source. Based on the optics theory and the simulation analysis, a novel dump system including an improved beam trap was proposed and installed. The measurement results indicate that the new dump system can reduce more than 60% of the stray light for the diagnostic system, and the influence of stray light on the error of measured density decreases.

  20. Characterization, Modeling, and Optimization of Light-Emitting Diode System

    DEFF Research Database (Denmark)

    Thorseth, Anders

    . It is shown that the droop in quantum efficiency can be approximated by a simple parabolic function. The investigated models of the spectral power distributions (SPD) from LEDs are the strictly empirical single and double Gaussian functions, and a semi empirical model using quasi Fermi levels and other basic...... solid state principles. The models are fitted to measured SPDs, using the free parameters. The result show a high correlation between the measured LED SPD and the fitted models. When comparing the chromaticity of the measured SPD with fitted models, the deviation is found to be larger than the lower...... limit of human color perception. A method has been developed to optimize multicolored cluster LED systems with respect to light quality, using multi objective optimization. The results are simulated SPDs similar to traditional light sources, and with high light quality. As part of this work...

  1. Design of the optocoupler applied to medical lighting systems.

    Science.gov (United States)

    Yang, Xibin; Lit, Rui; Zhu, Jianfeng; Xiong, Daxi

    2012-12-01

    A new type of optocoupler applied to medical lighting system is proposed, and the principle, Etendue and design process is introduced. With the help of Tracrpro, modeling and simulation of the optocoupler is conducted and the parameters are optimized. Analysis of factors affecting the energy coupling efficiency is done. With a view towards the development of Ultra High Brightness Light Emitting Diodes (UHB-LEDs), which play an important role a new sources of lighting in various biomedical devices, including those used in diagnosis and treatment, a series of simulations are executed and a variety of solutions are achieved. According to simulation results, the design target of coupling efficiency is achieved and the optical uniformity is also significantly improved. According to the result of theoretical analysis, verification experiments are designed and simulation results are verified. The optocoupler, which has simple structure, compact size and low cost, is suitable for applications in the field of low-cost medical domain.

  2. Fresh meat color evaluation using a structured light imaging system

    DEFF Research Database (Denmark)

    Trinderup, Camilla Himmelstrup; Kim, Yuan H. Brad

    2015-01-01

    The objective of this study was to investigate the efficacy of a computer vision system (CVS) with structured light for meat color assessment. Three muscles (longissimus dorsi (LD), semimembranosus (SM), and psoas major (PM)) from eight beef carcasses were obtained at 1 day postmortem, vacuum...... packaged and assigned to three aging periods (9, 16, and 23 days). After aging, steaks were cut and displayed for 7 days at 3 °C under light. The surface colors were evaluated by using a Minolta, the CVS and trained color panel. In general, the CVS was highly correlated to the sensory scores, and showed...... an equivalent meat color assessment compared to the colorimeter. The CVS had a significantly higher correlation with the panel scores for the lighter and more color stable samples compared to the colorimeter. These results indicate that the CVS with structured light could be an appropriate alternative...

  3. Perceived performance of daylighting systems: lighting efficacy and agreeableness

    Energy Technology Data Exchange (ETDEWEB)

    Fontoynont, M. [Ecole Nationale des Travaux Publics de l' Etat (France). Dept. Genie Civil et Batiment

    2002-08-01

    Can daylighting systems be assessed through objective procedures? On one hand, they can be considered as lighting techniques and deserve to be characterised through the same type of parameters: illuminances, uniformity, luminances, colour temperature, colour rendering indices, etc. On the other hand, two major aspects differentiate them from artificial lighting installations. Firstly, the daylight source is variable, requiring a long term approach and an assessment of the duration of the phenomena per day, month or year. Secondly, the brightness of the window cannot be totally disconnected from the content of the view and its agreeableness. This suggests that psychological well-being may be in some cases as important as visual comfort issues. For the window component industry, it appears that a serious concern about the two aspects of windows - i.e. lighting efficacy and agreeableness - should be carefully approached for each design. (author)

  4. A Multi-Agent System Approach Applied to Light Raycasting

    Directory of Open Access Journals (Sweden)

    H. Andrade

    2012-08-01

    Full Text Available Light and shadows caused by the interaction with objects are important features in computer graphics which areusually taken into account to achieve realistic images. In order to simulate them, some attempts have been carried outwhich are based on direct illumination classical approaches as shadow mapping and shadow volumes. However,classical approaches in their beginnings could not support semi-transparent objects, soft-shadows, light interactionsinside objects and the possibility to update a scene based on previous information.In this paper a novel shadow casting approach is proposed to solve the previously mentioned problem using aninteractive cooperative multi agent system to provide a better understanding and easy customization of the renderedscenes; for instance, the scenes are represented with object agents that propagate rectilinear photon informationthrough them causing several changes on photon properties such as wavelength, intensity, among others. Thissystem uses a two-dimensional space represented by pixels.Our multi-agent system (MAS uses a blackboard architecture for storing and sharing data and the implicit invocationdesign pattern. The system was developed to calculate direct illumination in a two-dimensional space. In addition, theproposed system supports point light agents, opaque agents, semi-opaque agents and empty agents.A comparison is presented between the classic approaches and the proposed one presented in this work in scenescomposed of opaque and semi-opaque objects. The proposed approach, as opposed to the classical ones, allows theshadows to be casted by the light that passes through semi-opaque objects. The light is casted by one or many lightagents producing hard and soft shadows.

  5. Application of Remote FPGA Dynamic Reconfiguration System in LED Lighting

    Institute of Scientific and Technical Information of China (English)

    LI Wei; WANG Wei; NIU Ping-juan; ZHANG li-ping

    2009-01-01

    The dynamic reconfiguration technique based on field-programmable gate array (FPGA) can improve the resource utilization.Discussed are the dynamic reconfiguration principles and methods.Proposed is a remote dynamic reconfiguration scheme using Xilinx Virtex-II FPGA and SMCS Ethernet Physical layer transceiver(PHY).The hardware of the system is designed with Xilinx Virtex-II XC2V30P FPGA that embedds MicroBlaze and MAC IP core,and its network communication software based on transmission control protocol/Internet protocol (TCP/IP) protocol is programmed by loading LwlP to MicroBlaze. The experimental results indicate that the remote FPGA dynamic reconfiguration system(RFDRS) can switch freely in the eight lighting modes of light emitting diodes (LED),and that,using dynamic reconfiguration technology,FPGA resource utilization can be reduced remarkably,which is advantageous in the system upgrade and software update.

  6. Optimal Energy Transfer in Light-Harvesting Systems

    Directory of Open Access Journals (Sweden)

    Lipeng Chen

    2015-08-01

    Full Text Available Photosynthesis is one of the most essential biological processes in which specialized pigment-protein complexes absorb solar photons, and with a remarkably high efficiency, guide the photo-induced excitation energy toward the reaction center to subsequently trigger its conversion to chemical energy. In this work, we review the principles of optimal energy transfer in various natural and artificial light harvesting systems. We begin by presenting the guiding principles for optimizing the energy transfer efficiency in systems connected to dissipative environments, with particular attention paid to the potential role of quantum coherence in light harvesting systems. We will comment briefly on photo-protective mechanisms in natural systems that ensure optimal functionality under varying ambient conditions. For completeness, we will also present an overview of the charge separation and electron transfer pathways in reaction centers. Finally, recent theoretical and experimental progress on excitation energy transfer, charge separation, and charge transport in artificial light harvesting systems is delineated, with organic solar cells taken as prime examples.

  7. A Novel Keyless Entry System Using Visible Light Communication

    Directory of Open Access Journals (Sweden)

    Kuniyoshi Okuda

    2014-10-01

    Full Text Available A major conventional car key is the mechanical key. When users inserted the key into a cylinder mechanical key and turn, users can unlock. The mechanical key may be able to be worn away for physical contact. And it may be impossible to use. Further the mechanical key may be damaged or destroyed by mischief. So a keyless entry system has been developed. The keyless entry system locks and unlocks using the infrared ray and radio waves communication. The keyless entry system does not require physical contacts. Therefore, the possibilities of damage due to mischief and be worn away are fell. However, the transmission ranges of infrared ray and radio waves communication are not clear. Submitting data might be tapped to the malicious people. If the information is tapped, then you have theft of the car and the risk of car break. We propose a keyless entry system using visible light communication in order to solve this problem. Visible light communication transmits signal using blinking light. Thus the transmission range is clear. The user can transmit the information only to the aimed place. Therefore, the usability is improved. We measure the durations of "take out the remote control", "put the aim" and "takes to unlock key" in order to evaluate the usability in the experiment. We also compared with the infrared ray communication and examined the superiority. Usability is improved in the experimental results, and usability is better than conventional keyless entry system.

  8. Optimal Energy Transfer in Light-Harvesting Systems.

    Science.gov (United States)

    Chen, Lipeng; Shenai, Prathamesh; Zheng, Fulu; Somoza, Alejandro; Zhao, Yang

    2015-08-20

    Photosynthesis is one of the most essential biological processes in which specialized pigment-protein complexes absorb solar photons, and with a remarkably high efficiency, guide the photo-induced excitation energy toward the reaction center to subsequently trigger its conversion to chemical energy. In this work, we review the principles of optimal energy transfer in various natural and artificial light harvesting systems. We begin by presenting the guiding principles for optimizing the energy transfer efficiency in systems connected to dissipative environments, with particular attention paid to the potential role of quantum coherence in light harvesting systems. We will comment briefly on photo-protective mechanisms in natural systems that ensure optimal functionality under varying ambient conditions. For completeness, we will also present an overview of the charge separation and electron transfer pathways in reaction centers. Finally, recent theoretical and experimental progress on excitation energy transfer, charge separation, and charge transport in artificial light harvesting systems is delineated, with organic solar cells taken as prime examples.

  9. Transition from closed system to Internet of Things: A study in standardizing building lighting systems

    NARCIS (Netherlands)

    Mathews, E.; Muller, G.

    2016-01-01

    Internet of Things (IoT) is triggering changes in lighting industry from the traditional closed and propriety systems to flexible, interoperable and service oriented systems. To address the challenges of this transition and catering the specific requirements of lighting networks, an Open Architectur

  10. Efficient distributed control of light-emitting diode array lighting systems.

    Science.gov (United States)

    Dong, Jianfei; Pandharipande, Ashish

    2012-07-15

    We consider illumination rendering with distributed control of a lighting system with an array of light-emitting diodes (LEDs). As low-cost microprocessors become standard components in LED drivers, distributing the computation of the control signals to individual LED drivers becomes attractive. Common distributed control algorithms require each individual controller to exchange information with all the others and process it. This incurs too large a communication and processing overhead for a low-cost local controller. In this Letter, we propose a distributed control algorithm for achieving global illumination rendering, wherein a controller only needs to communicate within a selected neighborhood. We present design criteria for defining the communication neighborhood and study its impact on rendering performance.

  11. PS2013 Satellite Workshop on Photosynthetic Light-Harvesting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Niederman, Robert A. [Rutgers Univ., New Brunswick, NJ (United States); Blankenship, Robert E. [Washington Univ., St. Louis, MO (United States); Frank, Harry A. [Univ. of Connecticut, Storrs, CT (United States)

    2015-02-07

    These funds were used for partial support of the PS2013 Satellite Workshop on Photosynthetic Light-Harvesting Systems, that was held on 8-11 August, 2013, at Washington University, St. Louis, MO. This conference, held in conjunction with the 16th International Congress on Photosynthesis/St. Louis, continued a long tradition of light-harvesting satellite conferences that have been held prior to the previous six international photosynthesis congresses. In this Workshop, the basis was explored for the current interest in replacing fossil fuels with energy sources derived form direct solar radiation, coupled with light-driven electron transport in natural photosynthetic systems and how they offer a valuable blueprint for conversion of sunlight to useful energy forms. This was accomplished through sessions on the initial light-harvesting events in the biological conversion of solar energy to chemically stored energy forms, and how these natural photosynthetic processes serve as a guide to the development of robust bio-hybrid and artificial systems for solar energy conversion into both electricity or chemical fuels. Organized similar to a Gordon Research Conference, a lively, informal and collegial setting was established, highlighting the exchange of exciting new data and unpublished results from ongoing studies. A significant amount of time was set aside for open discussion and interactive poster sessions, with a special session devoted to oral presentations by talented students and postdoctoral fellows judged to have the best posters. This area of research has seen exceptionally rapid progress in recent years, with the availability of a number of antenna protein structures at atomic resolution, elucidation of the molecular surface architecture of native photosynthetic membranes by atomic force microscopy and the maturing of ultrafast spectroscopic and molecular biological techniques for the investigation and manipulation of photosynthetic systems. The conferees

  12. Relationship between Human Pupillary Light Reflex and Circadian System Status

    Science.gov (United States)

    Bonmati-Carrion, Maria Angeles; Hild, Konstanze; Isherwood, Cheryl; Sweeney, Stephen J.; Revell, Victoria L.; Skene, Debra J.; Rol, Maria Angeles; Madrid, Juan Antonio

    2016-01-01

    Intrinsically photosensitive retinal ganglion cells (ipRGCs), whose photopigment melanopsin has a peak of sensitivity in the short wavelength range of the spectrum, constitute a common light input pathway to the olivary pretectal nucleus (OPN), the pupillary light reflex (PLR) regulatory centre, and to the suprachiasmatic nuclei (SCN), the major pacemaker of the circadian system. Thus, evaluating PLR under short wavelength light (λmax ≤ 500 nm) and creating an integrated PLR parameter, as a possible tool to indirectly assess the status of the circadian system, becomes of interest. Nine monochromatic, photon-matched light stimuli (300 s), in 10 nm increments from λmax 420 to 500 nm were administered to 15 healthy young participants (8 females), analyzing: i) the PLR; ii) wrist temperature (WT) and motor activity rhythms (WA), iii) light exposure (L) pattern and iv) diurnal preference (Horne-Östberg), sleep quality (Pittsburgh) and daytime sleepiness (Epworth). Linear correlations between the different PLR parameters and circadian status index obtained from WT, WA and L recordings and scores from questionnaires were calculated. In summary, we found markers of robust circadian rhythms, namely high stability, reduced fragmentation, high amplitude, phase advance and low internal desynchronization, were correlated with a reduced PLR to 460–490 nm wavelengths. Integrated circadian (CSI) and PLR (cp-PLR) parameters are proposed, that also showed an inverse correlation. These results demonstrate, for the first time, the existence of a close relationship between the circadian system robustness and the pupillary reflex response, two non-visual functions primarily under melanopsin-ipRGC input. PMID:27636197

  13. Model independent control of lightly damped noise/vibration systems.

    Science.gov (United States)

    Yuan, Jing

    2008-07-01

    Feedforward control is a popular strategy of active noise/vibration control. In well-damped noise/vibration systems, path transfer functions from actuators to sensors can be modeled by finite impulse response (FIR) filters with negligible errors. It is possible to implement noninvasive model independent feedforward control by a recently proposed method called orthogonal adaptation. In lightly damped noise/vibration systems, however, path transfer functions have infinite impulse responses (IIRs) that cause difficulties in design and implementation of broadband feedforward controllers. A major source of difficulties is model error if IIR path transfer functions are approximated by FIR filters. In general, active control performance deteriorates as model error increases. In this study, a new method is proposed to design and implement model independent feedforward controllers for broadband in lightly damped noise/vibration systems. It is shown analytically that the proposed method is able to drive the convergence of a noninvasive model independent feedforward controller to improve broadband control in lightly damped noise/vibration systems. The controller is optimized in the minimum H2 norm sense. Experiment results are presented to verify the analytical results.

  14. Synergetic Effect between Lighting Efficiency Enhancement and Building Energy Reduction Using Alternative Thermal Operating System of Indoor LED Lighting

    Directory of Open Access Journals (Sweden)

    Byung-Lip Ahn

    2015-08-01

    Full Text Available We investigated the synergetic effect between light-emitting diode (LED lighting efficiency and building energy savings in heating and cooling using an alternative thermal operating system (ATOS of indoor LED lighting integrated with the ventilation system of a building as an active cooling device. The heat generated from LED lighting and the indoor lighting illuminance were experimentally determined. The indoor heat gains in cooling and heating periods were determined using measurement data; the annual energy savings of an office building in heating and cooling were calculated through simulation. The LED lighting illuminance increased by approximately 40% and the lighting contribution for indoor heat gain was 7.8% in summer, while 69.8% in winter with the ATOS. Consequently, the annual total energy use of the office building could be reduced by 5.9%; the energy use in cooling and heating was reduced by 18.4% and 3.3%, respectively.

  15. 33 CFR 150.519 - What are the requirements for emergency lighting and power systems?

    Science.gov (United States)

    2010-07-01

    ... emergency lighting and power systems? 150.519 Section 150.519 Navigation and Navigable Waters COAST GUARD... Specialty Equipment Emergency Lighting and Power Systems § 150.519 What are the requirements for emergency lighting and power systems? (a) The operator must test and inspect the emergency lighting and power...

  16. Plant lighting system with five wavelength-band light-emitting diodes providing photon flux density and mixing ratio control

    Directory of Open Access Journals (Sweden)

    Yano Akira

    2012-11-01

    Full Text Available Abstract Background Plant growth and development depend on the availability of light. Lighting systems therefore play crucial roles in plant studies. Recent advancements of light-emitting diode (LED technologies provide abundant opportunities to study various plant light responses. The LED merits include solidity, longevity, small element volume, radiant flux controllability, and monochromaticity. To apply these merits in plant light response studies, a lighting system must provide precisely controlled light spectra that are useful for inducing various plant responses. Results We have developed a plant lighting system that irradiated a 0.18 m2 area with a highly uniform distribution of photon flux density (PFD. The average photosynthetic PFD (PPFD in the irradiated area was 438 micro-mol m–2 s–1 (coefficient of variation 9.6%, which is appropriate for growing leafy vegetables. The irradiated light includes violet, blue, orange-red, red, and far-red wavelength bands created by LEDs of five types. The PFD and mixing ratio of the five wavelength-band lights are controllable using a computer and drive circuits. The phototropic response of oat coleoptiles was investigated to evaluate plant sensitivity to the light control quality of the lighting system. Oat coleoptiles irradiated for 23 h with a uniformly distributed spectral PFD (SPFD of 1 micro-mol m–2 s–1 nm–1 at every peak wavelength (405, 460, 630, 660, and 735 nm grew almost straight upwards. When they were irradiated with an SPFD gradient of blue light (460 nm peak wavelength, the coleoptiles showed a phototropic curvature in the direction of the greater SPFD of blue light. The greater SPFD gradient induced the greater curvature of coleoptiles. The relation between the phototropic curvature (deg and the blue-light SPFD gradient (micro-mol m–2 s–1 nm–1 m–1 was 2 deg per 1 micro-mol m–2 s–1 nm–1 m–1. Conclusions The plant lighting system, with a computer with a

  17. Architecture of a highly modular lighting simulation system

    CERN Document Server

    CERN. Geneva

    2014-01-01

    This talk will discuss the challenges before designing a highly modular, parallel, heterogeneous rendering system and their solutions. It will review how different lighting simulation algorithms could be combined to work together using an unified framework. We will discuss how the system can be instrumented for collecting data about the algorithms' runtime performance. The talk includes an overview of how collected data could be visualised in the computational domain of the lighting algorithms and be used for visual debugging and analysis. About the speaker Hristo Lesev has been working in the software industry for the last ten years. He has taken part in delivering a number of desktop and mobile applications. Computer Graphics programming is Hristo's main passion and he has experience writing extensions for 3D software like 3DS Max, Maya, Blender, Sketchup, and V-Ray. Since 2006 Hristo teaches Photorealistic Ray Tracing in the Faculty of Mathematics and Informatics at the Paisii Hilendarski...

  18. Natural Light Harvesting Systems: Unraveling the quantum puzzles

    CERN Document Server

    Thilagam, A

    2013-01-01

    In natural light harvesting systems, the sequential quantum events of photon absorption by specialized biological antenna complexes, charge separation, exciton formation and energy transfer to localized reaction centers culminates in the conversion of solar to chemical energy. A notable feature in these processes is the exceptionally high efficiencies (> 95 %) at which excitation is transferred from the illuminated protein complex site to the reaction centers. Such high exciton propagation rates within a system of interwoven biomolecular network structures, is yet to be replicated in artificial light harvesting complexes. A clue to unraveling the quantum puzzles of nature may lie in the observation of long lived coherences lasting several picoseconds in the electronic spectra of photosynthetic complexes, even in noisy environmental baths. A number of experimental and theoretical studies have been devoted to unlocking the links between quantum processes and information protocols, in the hope of finding answers...

  19. A compact light readout system for longitudinally segmented shashlik calorimeters

    CERN Document Server

    Berra, A.

    2016-09-11

    The longitudinal segmentation of shashlik calorimeters is challenged by dead zones and non-uniformities introduced by the light collection and readout system. This limitation can be overcome by direct fiber-photosensor coupling, avoiding routing and bundling of the wavelength shifter fibers and embedding ultra-compact photosensors (SiPMs) in the bulk of the calorimeter. We present the first experimental test of this readout scheme performed at the CERN PS-T9 beamline in 2015 with negative particles in the 1-5~GeV energy range. In this paper, we demonstrate that the scheme does not compromise the energy resolution and linearity compared with standard light collection and readout systems. In addition, we study the performance of the calorimeter for partially contained charged hadrons to assess the $e/\\pi$ separation capability and the response of the photosensors to direct ionization.

  20. Portable light transmission measuring system for preserved corneas

    Science.gov (United States)

    Ventura, Liliane; de Jesus, Gabriel Torres; de Oliveira, Gunter Camilo Dablas; Sousa, Sidney JF

    2005-01-01

    Background The authors have developed a small portable device for the objective measurement of the transparency of corneas stored in preservative medium, for use by eye banks in evaluation prior to transplantation. Methods The optical system consists of a white light, lenses, and pinholes that collimate the white light beams and illuminate the cornea in its preservative medium, and an optical filter (400–700 nm) that selects the range of the wavelength of interest. A sensor detects the light that passes through the cornea, and the average corneal transparency is displayed. In order to obtain only the tissue transparency, an electronic circuit was built to detect a baseline input of the preservative medium prior to the measurement of corneal transparency. The operation of the system involves three steps: adjusting the "0 %" transmittance of the instrument, determining the "100 %" transmittance of the system, and finally measuring the transparency of the preserved cornea inside the storage medium. Results Fifty selected corneas were evaluated. Each cornea was submitted to three evaluation methods: subjective classification of transparency through a slit lamp, quantification of the transmittance of light using a corneal spectrophotometer previously developed, and measurement of transparency with the portable device. Conclusion By comparing the three methods and using the expertise of eye bank trained personnel, a table for quantifying corneal transparency with the new device has been developed. The correlation factor between the corneal spectrophotometer and the new device is 0,99813, leading to a system that is able to standardize transparency measurements of preserved corneas, which is currently done subjectively. PMID:16372912

  1. Scattering of light by a system of anisotropic particles.

    Science.gov (United States)

    Du, Xinyue; Zhao, Daomu

    2010-05-15

    The cross-spectral density function of the scattered field that is produced by scattering of a coherent plane light wave incident on a collection of different types of anisotropic particles is derived. We show the phenomena of interference of the fields scattered by each of the particles in the system. Numerical results indicate that the information about the shape, the distance, and the relative orientation of the particles may be obtained from far-zone measurements of the scattered field.

  2. Application research of tune measurement system in Hefei light source

    CERN Document Server

    Sun Bao Gen; Xu Hong Liang; Lu Ping; Wang Jun; Gao Yun Feng; Wang Li; LiuJinYing

    2002-01-01

    The author introduces the measurement and research of some beam parameters using tune measurement system for Hefei Light Source (HLS), which include the betatron tune, beta function, natural chromaticity, corrected chromaticity, and central frequency. Additionally, it also describes the measurement of the influence of DC clearing electrodes on the betatron tune shift and gives some measurement results. The measurement results are compared with the theoretical values and they are in good agreement

  3. Red Light-Green Light: A Classwide Management System for Students with Behavior Disorders in Primary Grades.

    Science.gov (United States)

    Barbetta, Patricia M.

    1990-01-01

    Red Light-Green Light is a levels system providing immediate behavior modification feedback and varying privilege levels throughout the school day for primary students with behavior disorders. This article presents guidelines for implementation, covering development of classroom rules, classroom expectations, and system maintenance. Tips for…

  4. Light

    CERN Document Server

    Robertson, William C

    2003-01-01

    Why is left right and right left in the mirror? Baffled by the basics of reflection and refraction? Wondering just how the eye works? If you have trouble teaching concepts about light that you don t fully grasp yourself, get help from a book that s both scientifically accurate and entertaining with Light. By combining clear explanations, clever drawings, and activities that use easy-to-find materials, this book covers what science teachers and parents need to know to teach about light with confidence. It uses ray, wave, and particle models of light to explain the basics of reflection and refraction, optical instruments, polarization of light, and interference and diffraction. There s also an entire chapter on how the eye works. Each chapter ends with a Summary and Applications section that reinforces concepts with everyday examples. Whether you need a deeper understanding of how light bends or a good explanation of why the sky is blue, you ll find Light more illuminating and accessible than a college textbook...

  5. Development of flying spot illumination system for stage lighting

    Science.gov (United States)

    Asakawa, Hisashi; Ishii, Katsunori; Koshiro, Hikari; Baba, Junko; Wakaki, Moriaki

    2014-02-01

    The system to control the area of illumination is important for the luminaires used for stages and TV studios. Presently the methods to change the distance between a lamp and lenses, or to use a zooming projection of the aperture illuminated by the lamp are used to control the area. However, these methods require many optical components or mechanical components. Moreover, the energy of the light source is partially consumed by the absorption of the shutter on adjusting the illumination area. On the other hand, the control of the illuminance over the illuminated area is not possible by the methods. In this study, we developed the lighting system which enables to control both the illuminated area and the illuminance distribution within the area by scanning the beam from a LED array light source. The area of illumination was expanded along one dimension by scanning the LED beam using a rotating polygon mirror. The selection of the illuminated width and the control of the illuminance distribution were achieved by synchronizing the pulse width modulation (PWM) control of the LED with the rotation of the mirror using a time sharing control. As a result, various illuminance distributions can be realized at real time by using software control for the luminaire. The developed system has the merits of compact and high efficiency.

  6. A practical method for the assessment of daylight-responsive lighting control systems regarding energy savings and lighting quality

    Energy Technology Data Exchange (ETDEWEB)

    Belendorf, H.; Aydinli, S.; Kaase, H. [Technical Univ. of Berlin, Inst. for Electronics and Lighting Technology, Berlin (Germany)

    2000-07-01

    The increased utilization of daylight-responsive lighting-control systems in commercial buildings requires the possibility to compare different systems regarding energy and lighting performance. Measurements at the Technical University of Berlin (TUB) on various daylight-responsive lighting controls have been made analyzing the energy saving potential and ability to fulfill general lighting requirements. The paper describes a basis for the calculation founded on these test-measurements in 1:1 test-rooms in order to assess the energy and lighting performance of the system as well as calculating a general quantity (the system-triple) per room-zone to classify and compare different systems. The method meets practical requirements because it takes into account the official guidelines for lighting in offices (dependent on the specific country, e.g. in Germany the standard DIN5035 'Artificial Lighting of Interiors' or other equivalent European standards). The quantity called system-triple consists of three numbers, of which one number describes the energy saving performance (system-potential), the other two relate to the behavior towards its maintaining the requirements to the illuminance level in the room (relative short-coming and exceeding light exposure). The system-potential tends to be independent from the sky-condition, although the situation in which the system is going to be applied has quite an influence on the system-potential. The method is an essential part of a comprehensive procedure, developed at the TUB, for predicting the energy saving potential regarding electric lighting in an office equipped with daylight-following lighting control systems. (au)

  7. UV Microstereolithography System that uses Spatial Light Modulator Technology.

    Science.gov (United States)

    Chatwin, C; Farsari, M; Huang, S; Heywood, M; Birch, P; Young, R; Richardson, J

    1998-11-10

    A new stereophotolithography technique utilizing a spatial light modulator (SLM) to create three-dimensional components with a planar, layer-by-layer process of exposure is described. With this procedure it is possible to build components with dimensions in the range of 50 mum-50 mm and feature sizes as small as 5 mum with a resolution of 1 mum. A polysilicon thin-film twisted nematic SVGA SLM is used as the dynamic photolithographic mask. The system consists of eight elements: a UV laser light source, an optical shutter, beam-conditioning optics, a SLM, a multielement reduction lens system, a high-resolution translation stage, a control system, and a computer-aided-design system. Each of these system components is briefly described. In addition, the optical characteristics of commercially available UV curable resins are investigated with nondegenerate four-wave mixing. Holographic gratings were written at a wavelength of 351.1 nm and read at 632.8 nm to compare the reactivity, curing speed, shrinkage, and resolution of the resins. These experiments were carried out to prove the suitability of these photopolymerization systems for microstereolithography.

  8. System and Battery Charge Control for PV-Powered AC Lighting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Kern, G.

    1999-04-01

    This report reviews a number of issues specific to stand-alone AC lighting systems. A review of AC lighting technology is presented, which discusses the advantages and disadvantages of various lamps. The best lamps for small lighting systems are compact fluorescent. The best lamps for intermediate-size systems are high- or low-pressure sodium. Specifications for battery charging and load control are provided with the goal of achieving lamp lifetimes on the order of 16,000 to 24,000 hours and battery lifetimes of 4 to 5 years. A rough estimate of the potential domestic and global markets for stand-alone AC lighting systems is presented. DC current injection tests were performed on high-pressure sodium lamps and the test results are presented. Finally, a prototype system was designed and a prototype system controller (with battery charger and DC/AC inverter) was developed and built.

  9. SETI via Leakage from Light Sails in Exoplanetary Systems

    CERN Document Server

    Guillochon, James

    2015-01-01

    The primary challenge of rocket propulsion is the burden of needing to accelerate the spacecraft's own fuel, resulting in only a logarithmic gain in maximum speed as propellant is added to the spacecraft. Light sails offer an attractive alternative in which fuel is not carried by the spacecraft, with acceleration being provided by an external source of light. By artificially illuminating the spacecraft with beamed radiation, speeds are only limited by the area of the sail, heat resistance of its material, and power use of the accelerating apparatus. In this paper, we show that leakage from a light sail propulsion apparatus in operation around a solar system analogue would be detectable. To demonstrate this, we model the launch and arrival of a microwave beam-driven light sail constructed for transit between planets in orbit around a single star, and find an optimal beam frequency on the order of tens of GHz. Leakage from these beams yields transients with flux densities of 0.1 Jy and durations of seconds at 1...

  10. Integrated envelope and lighting systems for commercial buildings: a retrospective

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Eleanor S.; Selkowitz, Stephen E.

    1998-06-01

    Daylighting systems in use world-wide rarely capture the energy-savings predicted by simulation tools and that we believe are achievable in real buildings. One of the primary reasons for this is that window and lighting systems are not designed and operated as an integrated system. Our efforts over the last five years have been targeted toward (1) development and testing of new prototype systems that involve a higher degree of systems integration than has been typical in the past, and (2) addressing current design and technological barriers that are often missed with component-oriented research. We summarize the results from this body of cross-disciplinary research and discuss its effects on the existing and future practice of daylighting in commercial buildings.

  11. Visible Light Communication System Using an Organic Bulk Heterojunction Photodetector

    Directory of Open Access Journals (Sweden)

    Cristina de Dios

    2013-09-01

    Full Text Available A visible light communication (VLC system using an organic bulk heterojunction photodetector (OPD is presented. The system has been successfully proven indoors with an audio signal. The emitter consists of three commercial high-power white LEDs connected in parallel. The receiver is based on an organic photodetector having as active layer a blend of poly(3-hexylthiophene (P3HT and phenyl C61-butyric acid methyl ester (PCBM. The OPD is opto-electrically characterized, showing a responsivity of 0.18 A/W and a modulation response of 790 kHz at −6 V.

  12. Mathematical model for light scanning system based on circular laser

    Institute of Scientific and Technical Information of China (English)

    Peiquan Xu; Shun Yao; Fenggui Lu; Xinhua Tang; Wei Zhang

    2005-01-01

    A novel light scanning system based on circular laser trajectory for welding robot is developed. With the help of image processing technique, intelligent laser welding could be realized. According to laser triangulation algorithm and Scheimpflug condition, mathematical model for circular laser vision is built.This scanning system projects circular laser onto welded seams and recovers the depth of the welded seams,escapes from shortcomings of less information, explains ambiguity and single tracking direction inherent in "spot" or "line" type laser trajectory. Three-dimensional (3D) model for welded seams could be recognized after depth recovery. The imaging error is investigated also.

  13. All solution processed low turn-on voltage near infrared LEDs based on core-shell PbS-CdS quantum dots with inverted device structure.

    Science.gov (United States)

    Sanchez, Rafael S; Binetti, Enrico; Torre, Jose A; Garcia-Belmonte, G; Striccoli, Marinella; Mora-Sero, Ivan

    2014-08-07

    Colloidal semiconductor quantum dots (QDs) are extraordinarily appealing for the development of light emitting devices (LEDs) due to tunable and pure color emission, brightness and solution processability. This last advantage of the QD-LEDs is even more evident in the field of infrared emission where the devices currently used are prepared by high cost epitaxial techniques. Here we show the fabrication of low cost NIR QD-LEDs based on high quantum yield core-shell PbS-CdS QDs and a novel inverted device structure. Devices are produced using SnO2:F (FTO) as the conductive transparent contact, nanostructured TiO2 as the electron transport layer (ETL) and poly(3-hexylthiophene) P3HT as the hole transport layer (HTL). Despite the roughness of this ETL, the obtained external quantum efficiencies (EQEs) are similar to previously reported values, obtained with regular configuration and more expensive ITO substrates. A turn-on voltage as low as the QD band gap (1.47 eV) is achieved for a large area (1.54 cm(2)) and relatively stable QD-LEDs.

  14. Whole article corrigendum: "Surface-plasmon-enhanced GaN-LED based on the multilayered rectangular nano-grating" [Optics Communications 322 (2014) 66-72

    Science.gov (United States)

    Zhu, Jun; Zhang, Haosu; Zhu, Zhendong; Li, Qunqing; Jin, Guofan

    2017-02-01

    This article proposes a surface-plasmon-enhanced GaN-LED based on the multilayered rectangular nano-grating. This structure contains a SiO2 film, an Ag film and a HfO2 film sequentially coated on the rectangularly-patterned p-GaN layer. The Ag film is used to enhance the internal quantum efficiency. The HfO2 cover-layer symmetrizes the distribution of refractive index besides the Ag film to improve the light extraction efficiency and surface-plasmon (SP) extraction efficiency. The inserted SiO2 layer is utilized to further improve the SP extraction efficiency. The properties of SP modes and Purcell effect in this structure are investigated. The photoluminescence experiments demonstrate that its peak intensity of top-emission is about 2.5 times greater than that from the reference structure covered by a single-layer Ag film on the rectangularly-patterned p-GaN layer.

  15. Experiencing LED: Lighting: New Form and Experiential Qualities Emerging in Lighting Systems using LED

    DEFF Research Database (Denmark)

    Petersen, Kjell Yngve; Kristensen, Ole; Søndergaard, Karin

    2012-01-01

    The project investigates what new forms and qualities of light emerge from technologies such as LED, with a particular focus on basic form qualities and parameters. Existing linear functional understandings of the relation between light source, light flow, reflection and visibility is challenged ...... by relational understandings, where the materiality and visibility of the light emerge through mutual influences between several adaptive and transformative elements....

  16. Photovoltaic OLED Driver for Low-Power Stand-Alone Light-to-Light Systems

    DEFF Research Database (Denmark)

    Ploug, Rasmus Overgaard; Knott, Arnold

    2016-01-01

    Photovoltaic (PV) stand-alone systems need to achieve multiple energy conversion modes. I.e. the energy conversion from PV to a local energy storage as well as energy conversion from the energy storage to the load. This paper documents the practical design considerations for the development of a ...... conversion from photovoltaic panel to the battery, and 97 % in the area 1.4 W to 2 W for power delivery to the OLED.......Photovoltaic (PV) stand-alone systems need to achieve multiple energy conversion modes. I.e. the energy conversion from PV to a local energy storage as well as energy conversion from the energy storage to the load. This paper documents the practical design considerations for the development...... of a three-port-converter for this purpose optimized for the specifications for driving an Organic Light Emitting Diode (OLED) panel intended for lighting purposes. By using a three-port-converter, featuring shared components for each conversion mode, the converter reaches 97 % efficiency at 1.8 W during...

  17. Method for large-range structured light system calibration.

    Science.gov (United States)

    An, Yatong; Bell, Tyler; Li, Beiwen; Xu, Jing; Zhang, Song

    2016-11-20

    Structured light system calibration often requires the usage of a calibration target with a similar size as the field of view (FOV), which brings challenges to a large-range structured light system calibration since fabricating large calibration targets is difficult and expensive. This paper presents a large-range system calibration method that does not need a large calibration target. The proposed method includes two stages: (1) accurately calibrate intrinsics (i.e., focal lengths and principle points) at a near range where both the camera and projector are out of focus, and (2) calibrate the extrinsic parameters (translation and rotation) from camera to projector with the assistance of a low-accuracy, large-range three-dimensional (3D) sensor (e.g., Microsoft Kinect). We have developed a large-scale 3D shape measurement system with a FOV of 1120  mm×1900  mm×1000  mm. Experiments demonstrate our system can achieve measurement accuracy as high as 0.07 mm with a standard deviation of 0.80 mm by measuring a 304.8 mm diameter sphere. As a comparison, Kinect V2 only achieved mean error of 0.80 mm with a standard deviation of 3.41 mm for the FOV of measurement.

  18. Three-Port dc-dc Conversion in Light-to-Light Systems

    DEFF Research Database (Denmark)

    Mira Albert, Maria del Carmen

    Renewable energies, like solar or wind, provide unlimited, clean and free energy that helps reducing (CO2) emissions, which alleviates global warming and greenhouse effects. Moreover, the ability to produce off-grid electricity allows local electric power generation. However, the main disadvantage...... of the major renewable energies because the Sun is a vast, inexhaustible and clean resource. Photovoltaic cells transform sunlight into electrical energy and the generated power is proportional to the amount of solar irradiation. Light-emitting diodes (LEDs) present higher luminous efficiency and lifetime than....... Solar powered systems are particularly challenging in locations far from the equator, where the solar resource is scarce, especially during winter, since the amount of solar irradiation is small and the length of the day is short. Therefore, these systems need to be optimized by maximizing the energy...

  19. Light-Emitting Diodes in the Solid-State Lighting Systems

    CERN Document Server

    Sparavigna, Amelia Carolina

    2014-01-01

    Red and green light-emitting diodes (LEDs) had been produced for several decades before blue emitting diodes, suitable for lighting applications, were widely available. Today, we have the possibility of combining the three fundamental colours to have a bright white light. And therefore, a new form of lighting, the solid-state lighting, has now become a reality. Here we discuss LEDs and some of their applications in displays and lamps.

  20. Multipath Reflections Analysis on Indoor Visible Light Positioning System

    CERN Document Server

    Gu, Wenjun; Kavehrad, Mohsen

    2015-01-01

    Visible light communication (VLC) has become a promising research topic in recent years, and finds its wide applications in indoor environments. Particularly, for location based services (LBS), visible light also provides a practical solution for indoor positioning. Multipath-induced dispersion is one of the major concerns for complex indoor environments. It affects not only the communication performance but also the positioning accuracy. In this paper, we investigate the impact of multipath reflections on the positioning accuracy of indoor VLC positioning systems. Combined Deterministic and Modified Monte Carlo (CDMMC) approach is applied to estimate the channel impulse response considering multipath reflections. Since the received signal strength (RSS) information is used for the positioning algorithm, the power distribution from one transmitter in a typical room configuration is first calculated. Then, the positioning accuracy in terms of root mean square error is obtained and analyzed.

  1. Characterization, Modeling, and Optimization of Light-Emitting Diode Systems

    DEFF Research Database (Denmark)

    Thorseth, Anders

    This thesis explores, characterization, modeling, and optimization of light-emitting diodes (LED) for general illumination. An automated setup has been developed for spectral radiometric characterization of LED components with precise control of the settings of forward current and operating...... comparing the chromaticity of the measured SPD with tted models, the deviation is found to be larger than the lower limit of human color perception. A method has been developed to optimize multicolored cluster LED systems with respect to light quality, using multi objective optimization. The results...... temperature. The automated setup has been used to characterize commercial LED components with respect to multiple settings. It is shown that the droop in quantum efficiency can be approximated by a simple parabolic function. The investigated models of the spectral power distributions (SPD) from LEDs...

  2. Weak localization of light in superdiffusive random systems

    CERN Document Server

    Burresi, Matteo; Savo, Romolo; Bertolotti, Jacopo; Vynck, Kevin; Wiersma, Diederik S

    2011-01-01

    L\\'evy flights constitute a broad class of random walks that occur in many fields of research, from animal foraging in biology, to economy to geophysics. The recent advent of L\\'evy glasses allows to study L\\'evy flights in controlled way using light waves. This raises several questions about the influence of superdiffusion on optical interference effects like weak and strong localization. Super diffusive structures have the extraordinary property that all points are connected via direct jumps, meaning that finite-size effects become an essential part of the physical problem. Here we report on the experimental observation of weak localization in L\\'evy glasses and compare results with recently developed optical transport theory in the superdiffusive regime. Experimental results are in good agreement with theory and allow to unveil how light propagates inside a finite-size superdiffusive system.

  3. Longitudinal automatic control system for a light weight aircraft

    Directory of Open Access Journals (Sweden)

    Cristian VIDAN

    2016-12-01

    Full Text Available This paper presents the design of an automatic control system for longitudinal axis of a light weight aircraft. To achieve this goal it is important to start from the mathematical model in longitudinal plane and then to determine the steady-state parameters for a given velocity and altitude. Using MATLAB Software the mathematical model in longitudinal plane was linearized and the system transfer functions were obtained. To determine the automatic control design we analyzed the stability of the linearized model for each input. After the stability problem was solved, using MATLAB-Simulink Software we designed the control system architecture and we considered that the objective for a stable flight was to continuously adjust the pitch angle θ through control of elevator and velocity through control of the throttle. Finally, we analyzed the performance of the designed longitudinal control system and the results highlighted in graphs outline that the purpose for which it was designed was fulfilled.

  4. Super-resolution for scanning light stimulation systems

    Science.gov (United States)

    Bitzer, L. A.; Neumann, K.; Benson, N.; Schmechel, R.

    2016-09-01

    Super-resolution (SR) is a technique used in digital image processing to overcome the resolution limitation of imaging systems. In this process, a single high resolution image is reconstructed from multiple low resolution images. SR is commonly used for CCD and CMOS (Complementary Metal-Oxide-Semiconductor) sensor images, as well as for medical applications, e.g., magnetic resonance imaging. Here, we demonstrate that super-resolution can be applied with scanning light stimulation (LS) systems, which are common to obtain space-resolved electro-optical parameters of a sample. For our purposes, the Projection Onto Convex Sets (POCS) was chosen and modified to suit the needs of LS systems. To demonstrate the SR adaption, an Optical Beam Induced Current (OBIC) LS system was used. The POCS algorithm was optimized by means of OBIC short circuit current measurements on a multicrystalline solar cell, resulting in a mean square error reduction of up to 61% and improved image quality.

  5. Automatic spreader-container alignment system using infrared structured lights.

    Science.gov (United States)

    Liu, Yu; Wang, Yibo; Lv, Jimin; Zhang, Maojun

    2012-06-01

    This paper presents a computer-vision system to assist reach stackers to automatically align the spreader with the target container. By analyzing infrared lines on the top of the container, the proposed system is able to calculate the relative position between the spreader and the container. The invisible structured lights are equipped in this system to enable all-weather operation, which can avoid environmental factors such as shadows and differences in climate. Additionally, the lateral inclination of the spreader is taken into consideration to offer a more accurate alignment than other competing systems. Estimation errors are reduced through approaches including power series and linear regression. The accuracy can be controlled within 2 cm or 2 deg, which meets the requirements of reach stackers' operation.

  6. Status of the delta synchrotron light-monitoring-system

    CERN Document Server

    Berges, U

    2000-01-01

    A synchrotron radiation source like DELTA needs an optical monitoring system to measure the beam size at different points of the ring with high resolution and accuracy. The measurements with the present synchrotron light monitors show that beam sizes larger than 250 μm can be measured. The measured emittance is of the order of the theoretical values of the optics and goes down to 8 nm rad. The magnification of the system can simply be increased by adding another lens to measure smaller emittances and beamsizes down to 100 μm. In this case you still have an optical image of the beam available, but sometimes the position of the camera has to be adapted due to the great magnification of the optical system. The image processing system which is based on a VME Framegrabber makes a two dimensional gaussian fit to the images from different synchrotron light-monitors. First tests with monochromatic components of the synchrotron radiation (500 nm and 550 nm) and with short time cameras (shutter time...

  7. Light

    CERN Document Server

    Ditchburn, R W

    2011-01-01

    This classic study, available for the first time in paperback, clearly demonstrates how quantum theory is a natural development of wave theory, and how these two theories, once thought to be irreconcilable, together comprise a single valid theory of light. Aimed at students with an intermediate-level knowledge of physics, the book first offers a historical introduction to the subject, then covers topics such as wave theory, interference, diffraction, Huygens' Principle, Fermat's Principle, and the accuracy of optical measurements. Additional topics include the velocity of light, relativistic o

  8. Design of solar cell lighting and sun tracking system

    Energy Technology Data Exchange (ETDEWEB)

    Khaing, A.A. [Mandalay Technological Univ., Mandalay (Myanmar); Ministry of Science, Yangon (Myanmar)

    2008-07-01

    A solar cell lighting and sun tracking system was discussed and the characteristics of solar cells were studied. An SM50H solar module was analyzed with a maximum power rating of 50 W and a current rate of 3.15 A. The main components of the system include solar cells, charged controllers, and a sun tracking system. The solar tracker is an automatic control system designed to track the solar modules in relation to the sun's direction. A linear drive actuator was used to track the modules with an energy consumption rate between 24 and 36 DC voltages. Power output solar cell equations were presented along with a review of batteries used for stationary and portable solar energy equipment. Issues related to cost of tracking systems were discussed. System sizing recommendations were provided, and solar cell design requirements were reviewed. A comparison of tracking and fixed solar energy systems was presented for a day in Yangon, Myanmar. It was concluded that solar tracking systems can be used to provide energy in rural and remote areas. 18 refs., 4 tabs., 5 figs.

  9. Mobile health-monitoring system through visible light communication.

    Science.gov (United States)

    Tan, Yee-Yong; Chung, Wan-Young

    2014-01-01

    Promising development in the light emitting diode (LED) technology has spurred the interest to adapt LED for both illumination and data transmission. This has fostered the growth of interest in visible light communication (VLC), with on-going research to utilize VLC in various applications. This paper presents a mobile-health monitoring system, where healthcare information such as biomedical signals and patient information are transmitted via the LED lighting. A small and portable receiver module is designed and developed to be attached to the mobile device, providing a seamless monitoring environment. Three different healthcare information including ECG, PPG signals and HL7 text information is transmitted simultaneously, using a single channel VLC. This allows for a more precise and accurate monitoring and diagnosis. The data packet size is carefully designed, to transmit information in a minimal packet error rate. A comprehensive monitoring application is designed and developed through the use of a tablet computer in our study. Monitoring and evaluation such as heart rate and arterial blood pressure measurement can be performed concurrently. Real-time monitoring is demonstrated through experiment, where non-hazardous transmission method can be implemented alongside a portable device for better and safer healthcare service.

  10. Pixel detector system development at Diamond Light Source

    Science.gov (United States)

    Marchal, J.; Horswell, I.; Gimenez, E. N.; Tartoni, N.

    2010-10-01

    Hybrid pixel detectors consisting of an array of silicon photodiodes bump-bonded to CMOS read-out chips provide high signal-to-noise ratio and high dynamic range compared to CCD-based detectors and Image Plates. These detector features are important for SAXS experiments where a wide range of intensities are present in the images. For time resolved SAXS experiments, high frame rates are compulsory. The latest CMOS read-out chip developed by the MEDIPIX collaboration provides high frame rate and continuous acquisition mode. A read-out system for an array of MEDIPIX3 sensors is under development at Diamond Light Source. This system will support a full resolution frame rate of 1 kHz at a pixel counter depth of 12-bit and a frame rate of 30 kHz at a counter depth of 1 bit. Details concerning system design and MEDIPIX sensors characterization are presented.

  11. Lighting systems control; El control en los sistemas de iluminacion

    Energy Technology Data Exchange (ETDEWEB)

    Arriaga Alpizar, Eric [Instituto Politecnico Nacional (Mexico)]. E-mail: eric_aa@hotmail.com

    2006-04-15

    In any workplace the illumination systems are very important, nevertheless, it is essential to control them in order to save energy. This article presents the six following control strategies for the efficient electric power use: programming, lights only will be on when it is necessary; natural light use, illumination will be replaced by using sunlight; lumens level maintenance, average level illumination can be measured utilizing this method; adjustment, the lowest illumination average is required avoiding to affect the performance and adaptation-compensation, decreasing the system variation. In addition there are also control devices which will operate the system, such as automatic devices, presence sensors and photo sensors. [Spanish] Los sistemas de iluminacion son muy importantes en cualquier lugar de trabajo, no obstante, es necesario que tengan un control, para lograr ahorrar energia. Este articulo presenta seis estrategias de control para el uso eficiente de la energia electrica: la programacion, con esta medida solo se encenderia la luz cuando sea necesario; uso de luz natural, asi se puede prescindir de la iluminacion pues la luz solar cumple con su funcion; mantenimiento del nivel de lumenes, de esta manera se mantiene un nivel promedio de iluminacion; ajuste, se ocupa el nivel de luz mas bajo posible sin afectar el rendimiento y adaptacion-compensacion, reduce la variacion del sistema. Por otro lado tambien hay dispositivos de control, que haran el trabajo, tales como dispositivos automaticos, sensores de presencia y fotosensores.

  12. Automatic diagnosis and control of distributed solid state lighting systems.

    Science.gov (United States)

    Dong, Jianfei; van Driel, Willem; Zhang, Guoqi

    2011-03-28

    This paper describes a new design concept of automatically diagnosing and compensating LED degradations in distributed solid state lighting (SSL) systems. A failed LED may significantly reduce the overall illumination level, and destroy the uniform illumination distribution achieved by a nominal system. To our knowledge, an automatic scheme to compensate LED degradations has not yet been seen in the literature, which requires a diagnostic step followed by control reconfigurations. The main challenge in diagnosing LED degradations lies in the usually unsatisfactory observability in a distributed SSL system, because the LED light output is usually not individually measured. In this work, we tackle this difficulty by using pulse width modulated (PWM) drive currents with a unique fundamental frequency assigned to each LED. Signal processing methods are applied in estimating the individual illumination flux of each LED. Statistical tests are developed to diagnose the degradation of LEDs. Duty cycle of the drive current signal to each LED is re-optimized once a fault is detected, in order to compensate the destruction of the uniform illumination pattern by the failed LED.

  13. 10 Mb/s visible light transmission system using a polymer light-emitting diode with orthogonal frequency division multiplexing.

    Science.gov (United States)

    Le, Son T; Kanesan, T; Bausi, F; Haigh, P A; Rajbhandari, S; Ghassemlooy, Z; Papakonstantinou, I; Popoola, W O; Burton, A; Le Minh, H; Cacialli, F; Ellis, A D

    2014-07-01

    We present a newly designed polymer light-emitting diode with a bandwidth of ~350  kHz for high-speed visible light communications. Using this new polymer light-emitting diode as a transmitter, we have achieved a record transmission speed of 10  Mb/s for a polymer light-emitting diode-based optical communication system with an orthogonal frequency division multiplexing technique, matching the performance of single carrier formats using multitap equalization. For achieving such a high data-rate, a power pre-emphasis technique was adopted.

  14. Channel cooperation for anti-occlusion visible light communication systems

    Science.gov (United States)

    Liu, Yuxin; Huang, Zhitong; Li, Wei; Ji, Yuefeng

    2016-10-01

    The need to exchange data wirelessly has increased as the growth of the number of mobile devices. Visible light communication (VLC) is a promising technology to alleviate the growing traffic problem. However, the occlusion problem is a difficulty in VLC system. In order to solve the problem, an anti-occlusion VLC system has been proposed in this article. In this VLC system, we propose the channel cooperative selection mechanism, which is based on the best-response dynamics and best response strategies of the game theory. This mechanism uses bit error ratio (BER) as the utility function to optimize system performance. In addition, the system provides three candidate communication channels, including direct channel, indirect channel, and mixed channel, to active users who will select the optimal communication channel. Moreover, the anti-occlusion VLC system has many application scenarios, such as the office, which has practical significance. For verifying the validity of the proposed mechanism, we accomplish the simulation results in terms of BER and throughput in different communication cases. It is demonstrated that the proposed channel cooperative selection mechanism in VLC systems offers superior performance in environment of obstructions.

  15. Study on the color merging of white light and transmission properties of wavelength division multiplexing visible light communication system based on RGB light-emitting diodes

    Science.gov (United States)

    Wang, Guangye; Gao, Yingming; Wang, Jinpeng; Chen, Ailin; Li, Ping; Zou, Nianyu

    2016-10-01

    Visible light communication (VLC) systems have an advantage for simultaneously achieving communication and illumination. To strengthen the performance of VLC by using RGB light-emitting diodes (LEDs) while meeting the lighting requirements, the channel capacity and the transmission capability of the system are improved by utilizing the wavelength division multiplexing (WDM) technology. We make the chromaticity of the merged white light suitable for human eyes by the experiment. The parameters of merged white light based on RGB LEDs and the merging ratio data measured by the experiment are given. Hence, we study and analyze the eye diagrams and bit error rate (BER) of different optical channels. The simulation results show that maximum transmission rate of the output signal is up to 3.3 Gbit/s, and the BER is less than 10-5 with a transmission distance of 2.5 m while meeting standard illumination requirements.

  16. AN LED-BASED SOLAR SIMULATOR FOR RESEARCH, DEVELOPMENT, AND TESTING OF PHOTOVOLTAIC SPACE POWER SYSTEMS Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Solar cells are the critical power source for the majority of space missions. The advancement from single junction silicon cells to current, state-of-the-art, triple...

  17. Enhancing lean supply chain through traffic light quality management system

    Directory of Open Access Journals (Sweden)

    Md. Mazharul Islam

    2013-03-01

    Full Text Available Lean is a continuous journey to grow and excel the company. Any company want to develop and cope with the world pace must adopt lean. However, in most of the organizations the management culture or people’s mentality is not so good to embrace change. They have predestined mind set where no change is normally allowed. Lean is a cooperative way of working that involves all departments and all personnel to work together in a team for the betterment of the entire company. Without providing fixed solution of any problem it suggests the best way that people willingly accept to do. Lean normally deals with highest quality, shorter lead time and lowest cost. In Bangladesh, most of the garment manufacturing companies are experiencing a massive quality problem. We describe a case where traffic light, a tool of lean quality system was adopted to a garment manufacturing company in Bangladesh. We also provide the charts to contrast the before and after scenario in detail, in order to illustrate the company benefits. After the traffic light system being implemented, the quality status was improved, production capacity was increased; significant days were saved that enhanced the lead time and thus strengthen the supply chain.

  18. Internal gas target system for the DarkLight experiment

    Science.gov (United States)

    Friscic, Ivica

    2017-01-01

    The DarkLight experiment at Jefferson National Laboratory (JLab) will perform a search for a dark photon in the mass range from 10 to 100 MeV/c2. The experimental design requires very high luminosity, but at the same time must keep the background rate as low as possible. Therefore, the experiment will use the 100 MeV electron beam from JLab's Low Energy Recirculator Facility (LERF) and a windowless gas target. In the summer of 2016 we deployed Phase 1A of this experiment, including a thin-walled, windowless target, using narrow apertures to restrict the flow of gas and aggressive pumping systems to reduce the pressure outside of the target region. Here we present the current design of the DarkLight internal gas target system, its performance during the 2016 summer beam tests, and future prospects. This work is supported by DOE grant DE-FG02-94ER40818 and NSF grant PHY-1437402.

  19. A type system for PSPACE derived from light linear logic

    Directory of Open Access Journals (Sweden)

    Lucien Capedevielle

    2012-01-01

    Full Text Available We present a polymorphic type system for lambda calculus ensuring that well-typed programs can be executed in polynomial space: dual light affine logic with booleans (DLALB. To build DLALB we start from DLAL (which has a simple type language with a linear and an intuitionistic type arrow, as well as one modality which characterizes FPTIME functions. In order to extend its expressiveness we add two boolean constants and a conditional constructor in the same way as with the system STAB. We show that the value of a well-typed term can be computed by an alternating machine in polynomial time, thus such a term represents a program of PSPACE (given that PSPACE = APTIME. We also prove that all polynomial space decision functions can be represented in DLALB. Therefore DLALB characterizes PSPACE predicates.

  20. Structured light system calibration method with optimal fringe angle.

    Science.gov (United States)

    Li, Beiwen; Zhang, Song

    2014-11-20

    For structured light system calibration, one popular approach is to treat the projector as an inverse camera. This is usually performed by projecting horizontal and vertical sequences of patterns to establish one-to-one mapping between camera points and projector points. However, for a well-designed system, either horizontal or vertical fringe images are not sensitive to depth variation and thus yield inaccurate mapping. As a result, the calibration accuracy is jeopardized if a conventional calibration method is used. To address this limitation, this paper proposes a novel calibration method based on optimal fringe angle determination. Experiments demonstrate that our calibration approach can increase the measurement accuracy up to 38% compared to the conventional calibration method with a calibration volume of 300(H)  mm×250(W)  mm×500(D)  mm.

  1. 46 CFR 78.17-45 - Emergency lighting and power systems.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 3 2010-10-01 2010-10-01 false Emergency lighting and power systems. 78.17-45 Section... OPERATIONS Tests, Drills, and Inspections § 78.17-45 Emergency lighting and power systems. (a) It shall be the duty of the master to see that the emergency lighting and power systems are operated and...

  2. Integrated Automotive High-Power LED-Lighting Systems in 3D-MID Technology

    NARCIS (Netherlands)

    Thomas, W.

    2014-01-01

    The growing energy consumption of lighting as well as rising luminous efficacies and -fluxes of high-power Light Emitting Diodes (LEDs) have contributed to the widespread use of LEDs in modern lighting systems. One of the most prominent users of the LED-technology is automotive (exterior) lighting.

  3. Modeling of lighting behaviour of a hybrid lighting system in inner spaces of Building of Electrical Engineering

    Science.gov (United States)

    Amado, L.; Osma, G.; Villamizar, R.

    2016-07-01

    This paper presents the modelling of lighting behaviour of a hybrid lighting system - HLS in inner spaces for tropical climate. HLS aims to mitigate the problem of high electricity consumption used by artificial lighting in buildings. These systems integrate intelligently the daylight and artificial light through control strategies. However, selection of these strategies usually depends on expertise of designer and of available budget. In order to improve the selection process of the control strategies, this paper analyses the Electrical Engineering Building (EEB) case, initially modelling of lighting behaviour is established for the HLS of a classroom and an office. This allows estimating the illuminance level of the mixed lighting in the space, and energy consumption by artificial light according to different lighting control techniques, a control strategy based on occupancy and a combination of them. The model considers the concept of Daylight Factor (DF) for the estimating of daylight illuminance on the work plane for tropical climatic conditions. The validation of the model was carried out by comparing the measured and model-estimated indoor illuminances.

  4. Light relations and performance of signal grass in silvopastoral system

    Directory of Open Access Journals (Sweden)

    Cynara Oliveira Diniz Rodrigues

    2014-03-01

    Full Text Available The aim was to evaluate the influence of different spatial arrangements of trees [(3×2×20 m, (2×2×9 m and 2×9 m] and sampling sites (center of row spacing and side of tree rows with regard to the amount and quality of light in the understory of silvopastoral systems and their effects on the production and chemical composition of pasture. The experimental design was a randomized block in a split plot, with three replications. The sampling site affected absolute irradiance, photosynthetic active radiation (PAR, light interception (LI and red/far red ratio, with higher rates in the center of spacing. There were high and positive correlations between LI/leaf area index (LAI, LI/dry mater (DM and LAI/DM in the center and LI/LAI and FAR/DM in the side of tree rows. Spatial arrangement (3×2×20 m had higher rates for plant height (PH, DM and neutral detergent fiber rate, while (2×2×9 m had high leaf/stem ratio and crude protein rate. In the case of the sampling site, higher rates of PH and DM were reported in the center. Forage composition was not affected by sampling sites. Highest production of DM was obtained in the (3×2×20 m arrangement and improvements in forage composition were observed in denser arrangements.

  5. Unequal error control scheme for dimmable visible light communication systems

    Science.gov (United States)

    Deng, Keyan; Yuan, Lei; Wan, Yi; Li, Huaan

    2017-01-01

    Visible light communication (VLC), which has the advantages of a very large bandwidth, high security, and freedom from license-related restrictions and electromagnetic-interference, has attracted much interest. Because a VLC system simultaneously performs illumination and communication functions, dimming control, efficiency, and reliable transmission are significant and challenging issues of such systems. In this paper, we propose a novel unequal error control (UEC) scheme in which expanding window fountain (EWF) codes in an on-off keying (OOK)-based VLC system are used to support different dimming target values. To evaluate the performance of the scheme for various dimming target values, we apply it to H.264 scalable video coding bitstreams in a VLC system. The results of the simulations that are performed using additive white Gaussian noises (AWGNs) with different signal-to-noise ratios (SNRs) are used to compare the performance of the proposed scheme for various dimming target values. It is found that the proposed UEC scheme enables earlier base layer recovery compared to the use of the equal error control (EEC) scheme for different dimming target values and therefore afford robust transmission for scalable video multicast over optical wireless channels. This is because of the unequal error protection (UEP) and unequal recovery time (URT) of the EWF code in the proposed scheme.

  6. Light-induced electron localization in a quantum Hall system

    Science.gov (United States)

    Arikawa, T.; Hyodo, K.; Kadoya, Y.; Tanaka, K.

    2017-07-01

    An insulating bulk state is a prerequisite for the protection of topological edge states. In quantum Hall systems, the thermal excitation of delocalized electrons is the main route to breaking bulk insulation. In equilibrium, the only way to achieve a clear bulk gap is to use a high-quality crystal under high magnetic field at low temperature. However, bulk conduction could also be suppressed in a system driven out of equilibrium such that localized states in the Landau levels are selectively occupied. Here we report a transient suppression of bulk conduction induced by terahertz wave excitation between the Landau levels in a GaAs quantum Hall system. Strikingly, the Hall resistivity almost reaches the quantized value at a temperature where the exact quantization is normally disrupted by thermal fluctuations. The electron localization is realized by the long-range potential fluctuations, which are a unique and inherent feature of quantum Hall systems. Our results demonstrate a new means of effecting dynamical control of topology by manipulating bulk conduction using light.

  7. Structured Light-Based 3D Reconstruction System for Plants.

    Science.gov (United States)

    Nguyen, Thuy Tuong; Slaughter, David C; Max, Nelson; Maloof, Julin N; Sinha, Neelima

    2015-07-29

    Camera-based 3D reconstruction of physical objects is one of the most popular computer vision trends in recent years. Many systems have been built to model different real-world subjects, but there is lack of a completely robust system for plants. This paper presents a full 3D reconstruction system that incorporates both hardware structures (including the proposed structured light system to enhance textures on object surfaces) and software algorithms (including the proposed 3D point cloud registration and plant feature measurement). This paper demonstrates the ability to produce 3D models of whole plants created from multiple pairs of stereo images taken at different viewing angles, without the need to destructively cut away any parts of a plant. The ability to accurately predict phenotyping features, such as the number of leaves, plant height, leaf size and internode distances, is also demonstrated. Experimental results show that, for plants having a range of leaf sizes and a distance between leaves appropriate for the hardware design, the algorithms successfully predict phenotyping features in the target crops, with a recall of 0.97 and a precision of 0.89 for leaf detection and less than a 13-mm error for plant size, leaf size and internode distance.

  8. A Structured Light Sensor System for Tree Inventory

    Science.gov (United States)

    Chien, Chiun-Hong; Zemek, Michael C.

    2000-01-01

    Tree Inventory is referred to measurement and estimation of marketable wood volume in a piece of land or forest for purposes such as investment or for loan applications. Exist techniques rely on trained surveyor conducting measurements manually using simple optical or mechanical devices, and hence are time consuming subjective and error prone. The advance of computer vision techniques makes it possible to conduct automatic measurements that are more efficient, objective and reliable. This paper describes 3D measurements of tree diameters using a uniquely designed ensemble of two line laser emitters rigidly mounted on a video camera. The proposed laser camera system relies on a fixed distance between two parallel laser planes and projections of laser lines to calculate tree diameters. Performance of the laser camera system is further enhanced by fusion of information induced from structured lighting and that contained in video images. Comparison will be made between the laser camera sensor system and a stereo vision system previously developed for measurements of tree diameters.

  9. Structured Light-Based 3D Reconstruction System for Plants

    Directory of Open Access Journals (Sweden)

    Thuy Tuong Nguyen

    2015-07-01

    Full Text Available Camera-based 3D reconstruction of physical objects is one of the most popular computer vision trends in recent years. Many systems have been built to model different real-world subjects, but there is lack of a completely robust system for plants. This paper presents a full 3D reconstruction system that incorporates both hardware structures (including the proposed structured light system to enhance textures on object surfaces and software algorithms (including the proposed 3D point cloud registration and plant feature measurement. This paper demonstrates the ability to produce 3D models of whole plants created from multiple pairs of stereo images taken at different viewing angles, without the need to destructively cut away any parts of a plant. The ability to accurately predict phenotyping features, such as the number of leaves, plant height, leaf size and internode distances, is also demonstrated. Experimental results show that, for plants having a range of leaf sizes and a distance between leaves appropriate for the hardware design, the algorithms successfully predict phenotyping features in the target crops, with a recall of 0.97 and a precision of 0.89 for leaf detection and less than a 13-mm error for plant size, leaf size and internode distance.

  10. Characterization of hybrid lighting systems of the Electrical Engineering Building in the Industrial University of Santander

    Science.gov (United States)

    Galvis, D.; Exposito, C.; Osma, G.; Amado, L.; Ordóñez, G.

    2016-07-01

    This paper presents an analysis of hybrid lighting systems of Electrical Engineering Building in the Industrial University of Santander, which is a pilot of green building for warm- tropical conditions. Analysis of lighting performance of inner spaces is based on lighting curves obtained from characterization of daylighting systems of these spaces. A computation tool was made in Excel-Visual Basic to simulate the behaviour of artificial lighting system considering artificial control system, user behaviour and solar condition. Also, this tool allows to estimate the electrical energy consumption of the lighting system for a day, a month and a year.

  11. Inverse design of LED arrangement for visible light communication systems

    Science.gov (United States)

    Zheng, Huanhuan; Chen, Jian; Yu, Changyuan; Gurusamy, Mohan

    2017-01-01

    In this paper, an optimal LED arrangement for indoor visible light communications (VLC) is proposed and numerically investigated. By using the concept of inverse design, the LED distribution can be formulated as a convex optimization problem and resolved accordingly. We show that sufficient brightness and uniform signal to noise ratio (SNR) can be achieved within the indoor coverage by using the proposed optimal LED arrangement, thus enabling the terminal mobility for indoor VLC. In addition, the analysis of delay spread distribution over the receiving plane shows that the design exhibits enhanced tolerance of inter-symbol interference (ISI). With the consideration of cabling cost for practical implementation, the suboptimal LED arrangement design is also investigated. Numerical results indicate that the suboptimal design can reduce the power consumption of the system with acceptable performance degradation.

  12. Rethinking the Systems Engineering Process in Light of Design Thinking

    Science.gov (United States)

    2016-04-30

    the creative thinking process exhibited by designers and now used in many non-traditional design domains such as strategy formulation, business , and...Eversheim W., & Perrone G. (1997). A methodology for the reduction of imprecision in the engineering design process . European Journal of Operations...qÜáêíÉÉåíÜ=^ååì~ä= ^Åèìáëáíáçå=oÉëÉ~êÅÜ= póãéçëáìã= tÉÇåÉëÇ~ó=pÉëëáçåë= sçäìãÉ=f= = Rethinking the Systems Engineering Process in Light of Design Thinking

  13. A novel light tracing system with high-precision and high-sensitivity sensors setup

    Science.gov (United States)

    Lin, Chern-Sheng; Wu, Pin Yi; Tsai, Jen Min; Tseng, Yu Hung; Chen, Hsin-Hung; Hwang, Jiann-Lih

    2013-11-01

    This paper presents a novel light source tracing system, which is comprised of a light-tracing board, with four photo-sensors of different incline angles, correspondingly disposed on its four edges, which are adjustable according to the movement range of the light source in order to achieve light-tracing purposes. This system introduces the algorithm of four-edge-sensors with servo motors in each site to improve sensor's sensitivity. The measurement values of light perception can be feedback to the programmable logic controller by wireless transceiver module. After proportional-integral-derivative operation, the system can obtain the situation of light source. In a normal mode, the light source movement range is large, the range of the incline angle of the light sensors are also set to large to obtain wide detection angle. But in a locking mode, the incline angle of the light sensing plane decreases, thus, the measurement range reduces, and the sensitivity is higher.

  14. Autonomous shading and light deflection systems; Autarke Sonnenschutz- und Lichtlenksysteme

    Energy Technology Data Exchange (ETDEWEB)

    Klotz, F.H. [Zentrum fuer Sonnenenergie- und Wasserstoff-Forschung Baden-Wuerttemberg (ZSW), Stuttgart (Germany)

    1998-02-01

    The motivations for solar control and daylighting systems at buildings are the reduced use of conventional energy and the improved comfort, for living as well as for working. Light guiding devices can be used in order to obtain daylight still in the deep interior of a building or in order to illuminate special targets. Due to the daily and seasonal changes in the Sun`s position, these devices must be constantly adapted. Using simple and reliable passive thermohydraulic drive technology, many applications for daylighting systems become feasible which were of merely theoretical interest in the past. ZSW has started an initiative for the development of such building-integrated solar systems. This report shows the latest results. (orig.) [Deutsch] Energie- und Umweltaspekte sowie neuere Erkenntnisse der Chronobiologie fordern eine intelligentere und effizientere Architektur und Gebaeudetechnik. Eine zentrale Rolle spielen dabei die transparenten Bauteile (Fenster, Glasfassaden, Atrien, Oberlichter, etc.), da dort der hauptsaechliche Energieaustausch (Waerme, Luft) stattfindet. Eine wirksame Kontrolle dieses Energieflusses - im Kontext der saisonalen und diurnalen Schwankungn der Sonneneinstrahlung - ist der Schluessel zur Reduktion des Gebaeudeenergiebedarfs (Heizung, Kuehlung, Beleuchtung, Lueftung) und der Steigerung des visuellen und thermischen Komforts. Es wurde eine Entwicklungsinitiative fuer passive thermohydraulisch gefuehrte Sonnenschutz- und Lichtlenksysteme gestartet, die durch die Sonne selbst mit Energie versorgt und reguliert werden und damit vollkommen autark sind. Hieraus ergibt sich ein hohes Kostenreduktionspotential fuer den Betrieb solcher Anlagen. Ein Meilenstein dieser Entwicklungen ist der von ZSW fuer die Sonnenlichtlenkung entwickelte erste passive zweiachsig nachgefuehrte Heliostat, welcher bereits seit 16 Monaten stoerungsfrei in Betrieb ist. (orig.)

  15. 21 CFR 866.5550 - Immunoglobulin (light chain specific) immunological test system.

    Science.gov (United States)

    2010-04-01

    ... the reagents used to measure by immunochemical techniques both kappa and lambda types of light chain... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Immunoglobulin (light chain specific... Test Systems § 866.5550 Immunoglobulin (light chain specific) immunological test system....

  16. 46 CFR 35.10-15 - Emergency lighting and power systems-T/ALL.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Emergency lighting and power systems-T/ALL. 35.10-15... Emergency Requirements § 35.10-15 Emergency lighting and power systems—T/ALL. (a) Where fitted, it shall be the duty of the master to see that the emergency lighting and power systems are tested and...

  17. 46 CFR 97.15-30 - Emergency lighting and power systems.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Emergency lighting and power systems. 97.15-30 Section... VESSELS OPERATIONS Tests, Drills, and Inspections § 97.15-30 Emergency lighting and power systems. (a) Where fitted, it shall be the duty of the master to see that the emergency lighting and power...

  18. 46 CFR 196.15-30 - Emergency lighting and power systems.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Emergency lighting and power systems. 196.15-30 Section... VESSELS OPERATIONS Test, Drills, and Inspections § 196.15-30 Emergency lighting and power systems. (a) Where fitted, it shall be the duty of the master to see that the emergency lighting and power...

  19. Effects on biological systems of reflected light from a satellite power system

    Science.gov (United States)

    White, M.

    1981-01-01

    Light reflection produced by the satellite power system and the possible effects of that light on the human eye, plants, and animals were studied. For the human eye, two cases of reflected light, might cause eye damage if viewed for too long. These cases are: (1) if, while in low Earth orbit, the orbital transfer vehicle is misaligned to reflect the Sun to Earth there exists a maximum safe fixation time for the naked eye of 42.4 secs; (2) reflection from the aluminum paint on the back of the orbital transfer vehicle, while in or near low Earth orbit, can be safely viewed by the naked eye for 129 sec. For plants and animals the intensity and timing of light are not a major problem. Ways for reducing and/or eliminating the irradiances are proposed.

  20. Savings in Cooling Energy with a Thermal Management System for LED Lighting in Office Buildings

    Directory of Open Access Journals (Sweden)

    Byung-Lip Ahn

    2015-06-01

    Full Text Available Light-emitting diode (LED lighting should be considered for lighting efficiency enhancement, however, waste heat from light-emitting diode (LED lighting increases the internal cooling load during the summer season. In order to solve this problem we propose a thermal management system for light-emitting diode (LED lighting with a heat exchanger module integrated with the building’s heating, ventilation, and air conditioning (HVAC system to move the lighting’s waste heat outdoors. An experiment was carried out to investigate the thermal effects in a test chamber and the heat exchange rate between the heat sink and the duct air. The heat generated by the light-emitting diode (LED lighting was calculated as 78.1% of light-emitting diode (LED input power and the heat exchange rate of the lighting heat exchange module was estimated to be between 86.5% and 98.1% according to the light-emitting diode (LED input power and the flow rate of air passing the heat sink. As a result, the average light-emitting diode (LED lighting heat contribution rate for internal heat gain was determined as 0.05; this value was used to calculate the heating and cooling energy demand of the office building through an energy simulation program. In the simulation results, the cooling energy demand was reduced by 19.2% compared with the case of conventionally installed light-emitting diode (LED lighting.

  1. Inexpensive, pocket-sized LED-based fluorometer for undergraduate teaching laboratories and in-the-field chemical detection

    Science.gov (United States)

    Tiber, Gage; Basu, Partha; Corcovilos, Theodore A.

    2015-05-01

    Fluorometry is a standard experimental technique for the detection of chemical compounds in solution. Excitation light is absorbed by a sample and then longer-wavelength light is emitted. Typical laboratory fluorometers are large and expensive, making them poorly suited for field work and teaching laboratories. We present a simple battery-powered fluorometer built with off-the-shelf components and a 3D-printed body. The light sources are user-replaceable light emitting diodes (LEDs). Two independent light sources of different wavelengths allow ratiometric measurements of the sample. The detectors are photodiodes with interchangeable dielectric Fabry-Perot stack spectral filters. The light gathering optics are designed using non-imaging optics principles to maximize the amount of detected fluorescence light. We present the design of the device and demonstrate the sensitivity using a molecular detector of Pb2+ ions in solution. The absorption and emission wavelengths of the detector molecule change from 415 nm and 465 nm, resp., in the absence of Pb2+ to 389 nm and 423 nm, resp., in the presence of Pb2+. The estimated sensitivity of the fluorometer with this molecular detector is a few p.p.b.

  2. Evaluating an emergent behaviour algorithm in JCSP for energy conservation in lighting systems

    DEFF Research Database (Denmark)

    Kosek, Anna Magdalena; Syed, Aly; Kerridge, J.

    2011-01-01

    Since the invention of the light bulb, artificial light is accompanying people all around the world every day and night. As the light bulb itself evolved a lot through years, light control systems are still switch-based and require users to make most of the decisions about its behaviour. This pap...... presents an algorithm for emergent behaviour in a lighting system to achieve stable, user defined light level, while saving energy. The algorithm employs a parallel design and was tested using JCSP. © 2011 The authors and IOS Press. All rights reserved....

  3. The Application of Surveying Biochemistry Light Instrument in the Reaction System of Starch with Mn3+

    Institute of Scientific and Technical Information of China (English)

    Gu Zhengbiao; Wu Jiagen

    2000-01-01

    The possibility of the application of Surveying Biochemistry Light Instrument (SBLI) in the reaction system of starch with Mn3+was studied. The results showed: neither starch nor initiator(Mn3+) could produce light because no factor that could produce light existed in them. But starch could produce light when it was acted by Mn3 + and the intensity of light depended on the kind and concentration of starch, the amount of Mn3 +, the temperature and pH of the reaction system. In addition, the intensity of light decreased with the reaction time because of the gradual disappearance of starch free radicals.

  4. Benefits and challenges of controlling a LED AFS (Adaptive Front-lighting System) using fuzzy logic

    OpenAIRE

    2011-01-01

    Texto completo: acesso restrito. p.579−588 The vehicular illumination system has undergone considerable technological advances in recent decades such as the use of a Light Emitting Diode (LED) Adaptive Front-lighting System (AFS), which represents an industry breakthrough in lighting technology and is rapidly becoming one of the most important innovative technologies around the world in the lighting community. This paper presents AFS control alternatives using fuzzy logic (types 1...

  5. Excitation migration in fluctuating light-harvesting antenna systems.

    Science.gov (United States)

    Chmeliov, Jevgenij; Trinkunas, Gediminas; van Amerongen, Herbert; Valkunas, Leonas

    2016-01-01

    Complex multi-exponential fluorescence decay kinetics observed in various photosynthetic systems like photosystem II (PSII) have often been explained by the reversible quenching mechanism of the charge separation taking place in the reaction center (RC) of PSII. However, this description does not account for the intrinsic dynamic disorder of the light-harvesting proteins as well as their fluctuating dislocations within the antenna, which also facilitate the repair of RCs, state transitions, and the process of non-photochemical quenching. Since dynamic fluctuations result in varying connectivity between pigment-protein complexes, they can also lead to non-exponential excitation decay kinetics. Based on this presumption, we have recently proposed a simple conceptual model describing excitation diffusion in a continuous medium and accounting for possible variations of the excitation transfer pathways. In the current work, this model is further developed and then applied to describe fluorescence kinetics originating from very diverse antenna systems, ranging from PSII of various sizes to LHCII aggregates and even the entire thylakoid membrane. In all cases, complex multi-exponential fluorescence kinetics are perfectly reproduced on the entire relevant time scale without assuming any radical pair equilibration at the side of the excitation quencher, but using just a few parameters reflecting the mean excitation energy transfer rate as well as the overall average organization of the photosynthetic antenna.

  6. Microscale, printed LEDs for unusual lighting and display systems

    Science.gov (United States)

    Kim, Rak-Hwan; Kim, Dae-Hyeong; Xiao, Jianliang; Kim, Bong Hoon; Panilaitis, Bruce; Ghaffari, Roozbeh; Yao, Jimin; Li, Ming; Liu, Zhuangjian; Malyarchuk, Viktor; Kim, Dae Gon; Le, An-Phong; Nuzzo, Ralph G.; Kaplan, David L.; Omenetto, Fiorenzo G.; Huang, Yonggang; Kang, Zhan; Rogers, John A.

    2011-02-01

    Current technology development in light emitting diodes has enabled high efficiency operation, low energy consumption and lifetimes, thereby creating new possibilities in conventional display and lighting industry. Recent work is also creating more unusual uses in biomedicine and in sensing applications, where conformal contact over curvilinear surfaces is required. Here, ultrathin device geometries and optimized mechanical designs, including neutral mechanical plane layouts and serpentine interconnects, provide indicators and lighting modules with arbitrary shapes capable of integrated on nearly any type of substrates. Biomedical devices such as light emitting suture threads, and glove-mounted optical proximity sensors demonstrate the versatility of this strategy and create great new opportunities.

  7. Fluorescent light induces neurodegeneration in the rodent nigrostriatal system but near infrared LED light does not.

    Science.gov (United States)

    Romeo, Stefania; Vitale, Flora; Viaggi, Cristina; di Marco, Stefano; Aloisi, Gabriella; Fasciani, Irene; Pardini, Carla; Pietrantoni, Ilaria; Di Paolo, Mattia; Riccitelli, Serena; Maccarone, Rita; Mattei, Claudia; Capannolo, Marta; Rossi, Mario; Capozzo, Annamaria; Corsini, Giovanni U; Scarnati, Eugenio; Lozzi, Luca; Vaglini, Francesca; Maggio, Roberto

    2017-05-01

    We investigated the effects of continuous artificial light exposure on the mouse substantia nigra (SN). A three month exposure of C57Bl/6J mice to white fluorescent light induced a 30% reduction in dopamine (DA) neurons in SN compared to controls, accompanied by a decrease of DA and its metabolites in the striatum. After six months of exposure, neurodegeneration progressed slightly, but the level of DA returned to the basal level, while the metabolites increased with respect to the control. Three month exposure to near infrared LED light (∼710nm) did not alter DA neurons in SN, nor did it decrease DA and its metabolites in the striatum. Furthermore mesencephalic cell viability, as tested by [(3)H]DA uptake, did not change. Finally, we observed that 710nm LED light, locally conveyed in the rat SN, could modulate the firing activity of extracellular-recorded DA neurons. These data suggest that light can be detrimental or beneficial to DA neurons in SN, depending on the source and wavelength. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Human-inspired lighting the intention control in robot systems with of glare avoidance%Human-inspired lighting the intention control in robot systems with of glare avoidance

    Institute of Scientific and Technical Information of China (English)

    Chen Shengyong; Guan Qiu; Liu Sheng; Bi Dexue

    2011-01-01

    This paper presents some human-inspired strategies for lighting control in a robot system for best scene interpretation, where the main intention is to avoid possible glares or highlights occurring in images. It firstly compares the characteristics of human eyes and robot eyes. Then some evaluation criteria are addressed to assess the lighting conditions. A bio-inspired method is adopted to avoid the visual glare which is caused by either direct illumination from large light sources or indirect illumination reflected by smooth surfaces. Appropriate methods are proposed to optimize the pose and optical parameters of the light source and the vision camera.

  9. A multiple-input-multiple-output visible light communication system based on VCSELs and spatial light modulators.

    Science.gov (United States)

    Lu, Hai-Han; Lin, Ying-Pyng; Wu, Po-Yi; Chen, Chia-Yi; Chen, Min-Chou; Jhang, Tai-Wei

    2014-02-10

    A multiple-input-multiple-output (MIMO) visible light communication (VLC) system employing vertical cavity surface emitting laser (VCSEL) and spatial light modulators (SLMs) with 16-quadrature amplitude modulation (QAM)-orthogonal frequency-division multiplexing (OFDM) modulating signal is proposed and experimentally demonstrated. The transmission capacity of system is significantly increased by space-division demultiplexing scheme. With the assistance of low noise amplifier (LNA) and data comparator, good bit error rate (BER) performance, clear constellation map, and clear eye diagram are achieved for each optical channel. Such a MIMO VLC system would be attractive for providing services including data and telecommunication services. Our proposed system is suitably applicable to the lightwave communication system in wireless transmission.

  10. Ferns, mosses and liverworts as model systems for light-mediated chloroplast movements.

    Science.gov (United States)

    Suetsugu, Noriyuki; Higa, Takeshi; Wada, Masamitsu

    2016-11-17

    Light-induced chloroplast movement is found in most plant species, including algae and land plants. In land plants with multiple small chloroplasts, under weak light conditions, the chloroplasts move towards the light and accumulate on the periclinal cell walls to efficiently perceive light for photosynthesis (the accumulation response). Under strong light conditions, chloroplasts escape from light to avoid photodamage (the avoidance response). In most plant species, blue light induces chloroplast movement, and phototropin receptor kinases are the blue light receptors. Molecular mechanisms for photoreceptors, signal transduction and chloroplast motility systems are being studied using the model plant Arabidopsis thaliana. However, to further understand the molecular mechanisms and evolutionary history of chloroplast movement in green plants, analyses using other plant systems are required. Here, we review recent works on chloroplast movement in green algae, liverwort, mosses and ferns that provide new insights on chloroplast movement.

  11. Comparison of stray light in spectrometer systems using a low cost monochromatic light source

    DEFF Research Database (Denmark)

    Thorseth, Anders; Lindén, Johannes; Dam-Hansen, Carsten

    2014-01-01

    We present an experimental setup that is under development for automated stray light characterization of spectrometers. The setup uses a tuneable monochromator which enables this characterization on relatively cost low equipment. We present the measured line spread functions for two spectrometers...

  12. 46 CFR 109.211 - Testing of emergency lighting and power systems.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Testing of emergency lighting and power systems. 109.211... emergency power system is tested at least once each week; (2) Each emergency generator is tested at least... emergency lighting and power systems is tested every six months under actual connected load for a period...

  13. Implementation of a PV lighting system based on DC-DC converter with intelligent controlled approach

    Energy Technology Data Exchange (ETDEWEB)

    Hua, C.-C.; Chuang, D.-J. [National Yunlin Univ. of Science and Technology, Douliou, Yunlin, Taiwan (China). Dept. of Electrical Engineering; Chuang, C.-W. [National Yunlin Univ. of Science and Technology, Douliou, Yunlin, Taiwan (China). Graduate School of Engineering Science and Technology

    2007-07-01

    Photovoltaic (PV) lighting systems for municipalities represent one of the largest cost effective markets for PVs. The installation cost of just one or two utility power poles can justify the initial cost of a PV lighting system. However, many previous PV lighting systems have experienced a number of component failures including premature charge controller, battery, and ballast illumination failures. This paper presented the design and implementation of a digital high performance photovoltaic lighting system based on a microcontroller. A high brightness light-emitting diode (HBLED), was used as it can work at very high efficiency with a specially designed lighting power module. The proposed system consisted of a photovoltaic module, a light emitting diode (LED) lighting module, a bi-directional buck-boost converter and a battery. The paper analysed battery charging methods and proposed a control strategy and hardware implementation. The dimming control methods for LED were also discussed and compared. The experimental results were also provided to verify the theoretical analysis and design procedure of a digital controlled photovoltaic lighting system. It was concluded that the experimental results verified the performance of the proposed photovoltaic lighting system. 8 refs., 1 tab., 18 figs.

  14. Assembling and Using an LED-Based Detector to Monitor Absorbance Changes during Acid-Base Titrations

    Science.gov (United States)

    Santos, Willy G.; Cavalheiro, E´der T. G.

    2015-01-01

    A simple photometric assembly based in an LED as a light source and a photodiode as a detector is proposed in order to follow the absorbance changes as a function of the titrant volume added during the course of acid-base titrations in the presence of a suitable visual indicator. The simplicity and low cost of the electronic device allow the…

  15. Assembling and Using an LED-Based Detector to Monitor Absorbance Changes during Acid-Base Titrations

    Science.gov (United States)

    Santos, Willy G.; Cavalheiro, E´der T. G.

    2015-01-01

    A simple photometric assembly based in an LED as a light source and a photodiode as a detector is proposed in order to follow the absorbance changes as a function of the titrant volume added during the course of acid-base titrations in the presence of a suitable visual indicator. The simplicity and low cost of the electronic device allow the…

  16. Phosphors for solid-state lighting: New systems, deeper understanding

    Science.gov (United States)

    Denault, Kristin Ashley

    We explore the structure-composition-property relationships in phosphor materials using a multitude of structural and optical characterization methods including high resolution synchrotron X-ray and neutron powder diffraction and total scattering, low-temperature heat capacity, temperature- and time-resolved photoluminescence, and density functional theory calculations. We describe the development of several new phosphor compositions and provide an in-depth description of the structural and optical properties. We show structural origins of improved thermal performance of photoluminescence and methods for determining structural rigidity in phosphor hosts that may lead to improved luminescent properties. New white light generation strategies are also explored. We begin by presenting the development of a green-yellow emitting oxyfluoride solid-solution phosphor Sr2Ba(AlO4F)1- x(SiO5)x:Ce3+. An examination of the host lattice, and the local structure around the Ce3+ activator ions points to how chemical substitutions play a crucial role in tuning the optical properties of the phosphor. The emission wavelength can be tuned from green to yellow by tuning the composition, x. Photoluminescent quantum yield is determined to be 70+/-5% for some of the examples in the series with excellent thermal properties. Phosphor-converted LED devices are fabricated using an InGaN LED and are shown to exhibit high color rendering white light. Next, we identify two new phosphor solid-solution systems, (Ba1- xSrx)9 Sc2Si6O24:Ce3+,Li+ and Ba9(Y1-ySc y)2Si6O24:Ce3+. The substitution of Sr for Ba in (Ba1-xSrx ) 9Sc2Si6O24:Ce 3+,Li + results in a decrease of the alkaline earth-oxygen bond distances at all three crystallographic sites, leading to changes in optical properties. The room temperature photoluminescent measurements show the structure has three excitation peaks corresponding to Ce3+ occupying the three independent alkaline earth sites. The emission of (Ba 1- xSrx) 9Sc2Si 6O24:Ce3

  17. Control of the lighting system using a genetic algorithm

    Directory of Open Access Journals (Sweden)

    Čongradac Velimir D.

    2012-01-01

    Full Text Available The manufacturing, distribution and use of electricity are of fundamental importance for the social life and they have the biggest influence on the environment associated with any human activity. The energy needed for building lighting makes up 20-40% of the total consumption. This paper displays the development of the mathematical model and genetic algorithm for the control of dimmable lighting on problems of regulating the level of internal lighting and increase of energetic efficiency using daylight. A series of experiments using the optimization algorithm on the realized model confirmed very high savings in electricity consumption.

  18. High Efficiency SEPIC Converter For High Brightness Light Emitting Diodes (LEDs) System

    OpenAIRE

    Qin, Yaxiao

    2012-01-01

    ABSTRACT This thesis presents an investigation into the characteristics of and driving methods for light emitting diode (LED) lamp system. A comprehensive overview on the lighting development is proposed. The characteristic of the light emitting diode (LED) lamp is described and the requirements of the ballast for the light emitting diode (LED) lamp are presented. Although LED lamps have longer lifetime than fluorescent lamps, the short lifetime limitation of LED driver imposed by ele...

  19. Organic Materials Degradation in Solid State Lighting Applications

    NARCIS (Netherlands)

    Yazdan Mehr, M.

    2015-01-01

    In this thesis the degradation and failure mechanisms of organic materials in the optical part of LED-based products are studied. The main causes of discoloration of substrate/lens in remote phosphor of LED-based products are also comprehensively investigated. Solid State Lighting (SSL) technology i

  20. Organic Materials Degradation in Solid State Lighting Applications

    NARCIS (Netherlands)

    Yazdan Mehr, M.

    2015-01-01

    In this thesis the degradation and failure mechanisms of organic materials in the optical part of LED-based products are studied. The main causes of discoloration of substrate/lens in remote phosphor of LED-based products are also comprehensively investigated. Solid State Lighting (SSL) technology

  1. A Sand Control System for Light Oil Reservoir

    Institute of Scientific and Technical Information of China (English)

    Xiang Yuzhang

    1996-01-01

    @@ Over 30-year water flooding in light oil sandstone reservoirs with loose argillaceous cement in Karamay oilfield results in severe sand production, varying from well to well with the different date of well completion.

  2. Dynamic miniature lighting system with low correlated colour temperature and high colour rendering index for museum lighting of fragile artefacts

    DEFF Research Database (Denmark)

    Thorseth, Anders; Corell, Dennis Dan; Poulsen, Peter Behrensdorff

    2013-01-01

    Illumination of fragile and irreplaceable historical objects exhibited to the public presents challenges with regards to: good colour rendering, low photochemical degradation of sensitive materials and general energy consumption. We present a dynamic tri-colour LED lighting system for illumination...... of historical artefacts in display cases at museums and other exhibitions, which can replace 3-5 Watt incandescent light bulbs with a correlated colour temperature (CCT) from 2000 K to 2400 K. The solution decreases the energy consumption by up to 80 %, while maintaining colour rendering indices (Ra) above 90...

  3. Solid state lighting and photobiological safety

    Science.gov (United States)

    Soskind, Y. G.; Campin, J. A.; Hopler, M. D.; Pettit, G. H.

    2007-02-01

    Recent advancements in Light-Emitting Diode (LED) technology have led to significant proliferation of solid-state lighting in our every-day life. White light and monochrome LED-based solid-state sources provide a small size, lower power consumption, and longer life alternative to several types of traditional light sources, such as incandescent lights. However, the spectral characteristics of LEDs are significantly different from the spectra of self-luminous objects that human eyes are adapted to through evolution and, therefore, may pose a real threat of photic-induced eye injury. In this paper the spectral characteristics of individual sources are considered from a photobiological safety perspective, and are used to estimate the retinal hazard potential of LEDs relative to that for daylight and blackbody radiators. The presented LED source retinal hazard exposure ranking considerations could be accounted for during illumination system design to minimize photic-induced eye injury risk. The importance of the material presented herein can not be underestimated since high power LED sources are found in a variety of high volume lighting applications and systems including automotive lamps, signal lighting, flash lights and other illumination devices.

  4. LightTools软件在均匀光分布的照明系统设计中的应用%The application of LightTools software in uniform light distribution of the lighting system design

    Institute of Scientific and Technical Information of China (English)

    胡志威; 彭润玲; 秦汉; 林朋飞

    2012-01-01

    以模拟单颗LED的均匀配光为例,介绍了LightTools软件在照明系统设计中的应用,以便更进一步地掌握和使用LightTools软件.文中借助LightTools软件,在单颗LED上建立反光杯模型,在反光杯出光口建立透镜阵列,并在目标照射面上建立目标区域的强度网格,通过LightTools软件的优化模块进行优化后,可在目标区域得到均匀的光强分布.利用LightTools 软件进行辅助设计和优化模拟,具有很高的可信度,也可以大大缩短照明设计的周期.%With the simulation of single LED light distribution even as an example, LightTools software in lighting system design of the application is introduced in order to further control and use LightTools software. With LightTools software, a reflector model is established above a single LED component and lens array is made on the exit of the reflector, then an intensity mesh for a certain region of the target surface is established After optimization in LightTools, the intensity distribution can be uniform in the target area. The design and optimization with LightTools demonstrate high credibility, and the lighting design cycle could also be greatly shortened.

  5. Posture parameters optimization of a structured light 3D angle measuring system

    OpenAIRE

    2015-01-01

    To improve the measurement precision of the structured light target angle, this paper studies the relation between the structured light system parameters and measurement accuracy of the angle. Firstly, the main system structure parameters influencing the angle measurement precision are analyzed based on the structured light measurement principle; secondly, simulation research on the laws of how the structured parameters influence the angle measurement precision are conducted, and the optimize...

  6. Quantum Photonic in Hybrid Cavity Systems with Strong Matter-Light Couplings

    Science.gov (United States)

    2015-08-24

    AFRL-AFOSR-VA-TR-2015-0246 Quantum Photonic in Hybrid Cavity Systems with Strong Matter-Light Couplings Hui Deng UNIVERSITY OF MICHIGAN Final Report...TITLE AND SUBTITLE Quantum Photonic in Hybrid Cavity Systems with Strong Matter-Light Couplings 5a.  CONTRACT NUMBER 5b.  GRANT NUMBER FA9550-12-1-0256... photons was demonstrated in the designable microcavity structure for the first time, establishing a robust light-matter hybrid states with designable

  7. Analysis and simulation of an automated LED lighting system for pedestrian crosswalk

    Science.gov (United States)

    Ileana, Ioan; Risteiu, Mircea; Marc, Gheorghe; Sofalca, Ionut

    2015-02-01

    This paper approaches the design of a smart lighting system for efficient lighting of pedestrian crosswalks on streets, using power LEDs. Starting with existing solid-state lighting - SSL (power LEDs with individual directivity diagram, lighting efficiency and color rendering index - CRI) in the paper we propose a design technique and methodology in order to find the distribution geometry of light sources (sources number, spatial coordinates, fixing angles) that simultaneously satisfy the lighting regulation requests and energetic efficiency. The major achievements are the simulations of using of a great number of LED lighting sources and of spatial lighting configurations in order to obtain of a uniform lighting of the area of interest (fig.1) and in conformity with actual standards in a specified scenario. The direct consequence of these simulations is the using of an intelligent management system of LED lighting sources that will allow the optimization of light flux in real traffic conditions of cars and pedestrians. This means the monitoring of traffic level and surrounding conditions (temperature, humidity, natural lighting etc.) in order to efficient use the existing resources.

  8. Self-action of Bessel wave packets in a system of coupled light guides and formation of light bullets

    Energy Technology Data Exchange (ETDEWEB)

    Balakin, A. A., E-mail: balakin.alexey@yandex.ru; Mironov, V. A.; Skobelev, S. A., E-mail: sk.sa1981@gmail.com [Russian Academy of Sciences, Institute of Applied Physics (Russian Federation)

    2017-01-15

    The self-action of two-dimensional and three-dimensional Bessel wave packets in a system of coupled light guides is considered using the discrete nonlinear Schrödinger equation. The features of the self-action of such wave fields are related to their initial strong spatial inhomogeneity. The numerical simulation shows that for the field amplitude exceeding a critical value, the development of an instability typical of a medium with the cubic nonlinearity is observed. Various regimes are studied: the self-channeling of a wave beam in one light guide at powers not strongly exceeding a critical value, the formation of the “kaleidoscopic” picture of a wave packet during the propagation of higher-power radiation along a stratified medium, the formation of light bullets during competition between self-focusing and modulation instabilities in the case of three-dimensional wave packets, etc. In the problem of laser pulse shortening, the situation is considered when the wave-field stratification in the transverse direction dominates. This process is accompanied by the self-compression of laser pulses in well enough separated light guides. The efficiency of conversion of the initial Bessel field distribution to two flying parallel light bullets is about 50%.

  9. Deep-sea low-light radiometer system.

    Science.gov (United States)

    Haag, Justin M; Roberts, Paul L D; Papen, George C; Jaffe, Jules S; Li, Linhai; Stramski, Dariusz

    2014-12-01

    Two single-waveband low-light radiometers were developed to characterize properties of the underwater light field relevant to biological camouflage at mesopelagic ocean depths. Phenomena of interest were vertical changes in downward irradiance of ambient light at wavelengths near 470 nm and 560 nm, and flashes from bioluminescent organisms. Depth profiles were acquired at multiple deep stations in different geographic regions. Results indicate significant irradiance magnitudes at 560 nm, providing direct evidence of energy transfer as described by Raman scattering. Analysis of a night profile yielded multiple examples of bioluminescent flashes. The selection of high-sensitivity, high-speed silicon photomultipliers as detectors enabled measurement of spectrally-resolved irradiance to greater than 400 m depth.

  10. 49 CFR 571.135 - Standard No. 135; Light vehicle brake systems.

    Science.gov (United States)

    2010-10-01

    ... vehicle is determined by measuring the stopping distance from a given initial speed. S6.5.3.2. Unless... 49 Transportation 6 2010-10-01 2010-10-01 false Standard No. 135; Light vehicle brake systems. 571... Federal Motor Vehicle Safety Standards § 571.135 Standard No. 135; Light vehicle brake systems. S1. Scope...

  11. Maximizing the information transfer in a quantum-limited light-scattering system

    DEFF Research Database (Denmark)

    Lading, Lars; Jørgensen, Thomas Martini

    1990-01-01

    A quantum-limited light-scattering system is considered. The spatial configuration that maximizes a given figure of merit is investigated, assuming that the emitted light has Poisson photon statistics. A specific system for measuring the velocity of a small particle is considered as an example...

  12. 76 FR 9495 - Feathering Propeller Systems for Light-Sport Aircraft Powered Gliders

    Science.gov (United States)

    2011-02-18

    ... Administration 14 CFR Part 1 RIN 2120-AJ81 Feathering Propeller Systems for Light-Sport Aircraft Powered Gliders... propeller operation for powered gliders that qualify as light-sport aircraft. DATES: The effective date for... aircraft (LSA) had a fixed or autofeathering propeller system. The restriction to ``autofeathering''...

  13. Electrical and optical evaluation aspects of public lighting systems

    Science.gov (United States)

    Tulbure, Adrian; Marc, Gheorghe; Kurt, Ünal

    2016-12-01

    This paper briefs a few issues regarding the technical validation of public lighting solutions. The novelty of the work is justified by the fact that it combines technical legislation in force [1], with practical analysis procedures [2]. Thus, in order to select the optimal solution, the paper describes a case study of measurement procedure which confirms the high electrical and optical characteristics [3] of the proposed solutions. At the end of the contribution, comparative design purposes for the two versions of modern street lighting are presented.

  14. Rapidly reconfigurable slow-light system based on off-resonant Raman absorption

    Science.gov (United States)

    Vudyasetu, Praveen K.; Camacho, Ryan M.; Howell, John C.

    2010-11-01

    We present a slow-light system based on dual Raman absorption resonances in warm rubidium vapor. Each Raman absorption resonance is produced by a control beam in an off-resonant Λ system. This system combines all optical control of the Raman absorption and the low-dispersion broadening properties of the double Lorentzian absorption slow light. The bandwidth, group delay, and central frequency of the slow-light system can all be tuned dynamically by changing the properties of the control beam. We demonstrate multiple pulse delays with low distortion and show that such a system has fast switching dynamics and thus fast reconfiguration rates.

  15. Tuning the light in senior care: Evaluating a trial LED lighting system at the ACC Care Center in Sacramento, CA

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Robert G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wilkerson, Andrea M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-08-31

    This report summarizes the results from a trial installation of light-emitting diode (LED) lighting systems in several spaces within the ACC Care Center in Sacramento, CA. The Sacramento Municipal Utility District (SMUD) coordinated the project and invited the U.S. Department of Energy (DOE) to document the performance of the LED lighting systems as part of a GATEWAY evaluation. DOE tasked the Pacific Northwest National Laboratory (PNNL) to conduct the investigation. SMUD and ACC staff coordinated and completed the design and installation of the LED systems, while PNNL and SMUD staff evaluated the photometric performance of the systems. ACC staff also track behavioral and health measures of the residents; some of those results are reported here, although PNNL staff were not directly involved in collecting or interpreting those data. The trial installation took place in a double resident room and a single resident room, and the corridor that connects those (and other) rooms to the central nurse station. Other spaces in the trial included the nurse station, a common room called the family room located near the nurse station, and the ACC administrator’s private office.

  16. A Red-Light Running Prevention System Based on Artificial Neural Network and Vehicle Trajectory Data

    Directory of Open Access Journals (Sweden)

    Pengfei Li

    2014-01-01

    Full Text Available The high frequency of red-light running and complex driving behaviors at the yellow onset at intersections cannot be explained solely by the dilemma zone and vehicle kinematics. In this paper, the author presented a red-light running prevention system which was based on artificial neural networks (ANNs to approximate the complex driver behaviors during yellow and all-red clearance and serve as the basis of an innovative red-light running prevention system. The artificial neural network and vehicle trajectory are applied to identify the potential red-light runners. The ANN training time was also acceptable and its predicting accurate rate was over 80%. Lastly, a prototype red-light running prevention system with the trained ANN model was described. This new system can be directly retrofitted into the existing traffic signal systems.

  17. Traffic Light Control by Multiagent Reinforcement Learning Systems

    NARCIS (Netherlands)

    Bakker, B.; Whiteson, S.; Kester, L.J.H.M.; Groen, F.C.A.

    2010-01-01

    Traffic light control is one of the main means of controlling road traffic. Improving traffic control is important because it can lead to higher traffic throughput and reduced traffic congestion. This chapter describes multiagent reinforcement learning techniques for automatic optimization of

  18. Weak Localization of Light in Superdiffusive Random Systems

    NARCIS (Netherlands)

    Burresi, M.; Radhalaksimi, V.; Savo, R.; Bertolotti, J.; Vynck, K.; Wiersma, D.S.

    2012-01-01

    Lévy flights constitute a broad class of random walks that occur in many fields of research, from biology to economy and geophysics. The recent advent of Lévy glasses allows us to study Lévy flights—and the resultant superdiffusion—using light waves. This raises several questions about the influence

  19. Photonic antenna system for light harvesting, transport and trapping

    NARCIS (Netherlands)

    Calzaferri, G.; Pauchard, M.; Maas, H.; Huber, S.; Khatyr, A.; Schaafsma, T.J.

    2002-01-01

    Host¿guest composites with photonic antenna properties are described. The material consists of cylindrical zeolite L crystals the channels of which are filled with chains of joined but electronically non-interacting dye molecules. Light shining on a crystal is first absorbed and the energy is then t

  20. A new method to manipulate broiler chicken growth and metabolism: Response to mixed LED light system

    Science.gov (United States)

    Yang, Yefeng; Yu, Yonghua; Pan, Jinming; Ying, Yibin; Zhou, Hong

    2016-05-01

    Present study introduced a new method to manipulate broiler chicken growth and metabolism by mixing the growth-advantage LED. We found that the green/blue LED mixed light system (G-B and G × B) have the similar stimulatory effect on chick body weight with single green light and single blue light (G and B), compared with normal artificial light (P = 0.028). Moreover, the percentage of carcass was significantly greater in the mixed light (G × B) when compared with the single light (P = 0.003). Synchronized with body weight, the mixed light (G-B and G × B) had a significant improved influence on the feed conversion of birds compared with normal light (P = 0.002). A significant improvement in feed conversion were found in mixed light (G × B) compared with single LED light (P = 0.037). G group resulted in a greater high-density lipoprotein cholesterol level than B group (P = 0.002), whereas B group resulted in a greater low-density lipoprotein cholesterol level than G group (P = 0.017). The mixed light significantly increased the birds’ glucose level in comparison with the single light (P = 0.003). This study might establish an effective strategy for maximizing growth of chickens by mixed LED technology.

  1. Measurement of normalized spectral responsivity of digital imaging devices by using a LED-based tunable uniform source.

    Science.gov (United States)

    Mahmoud, Khaled; Park, Seongchong; Park, Seung-Nam; Lee, Dong-Hoon

    2013-02-20

    We present an instrumentation solution for measurement of normalized spectral responsivity of digital imaging sensors and cameras. The instrument consists of multiple light-emitting diodes (LEDs), a single-grating monochromator, and a small-size integrating sphere. Wavelength tuning is achieved by a proper selection of LED in accordance with the monochromator setting in a range from 380 to 900 nm. High spectral purity with a bandwidth of 5 nm is realized without using double gratings and order-sorting filters. Experimental characteristics and calibration of the instrument are described with the related error and uncertainty sources. The performance is demonstrated by measuring a monochrome charge-coupled device and a trichromatic complementary metal-oxide-semiconductor device. The measurement uncertainty is evaluated to be less than 1% (k=2) except several wavelengths with low LED power.

  2. Design and construction evaluation of a photovoltaic DC LED lighting system

    Science.gov (United States)

    Bhamidipati, Jyotsna

    2008-08-01

    The market demand for commercialization of Photovoltaic (PV) systems depends a lot on the reliability, efficiency and performance of various components within the system. PV panels produce DC power when exposed to sunlight, and an inverter converts this to AC power in a typical solar powered building. Though, PV lighting has existed for a long time it hasn't been very effective, as incandescent light sources were commonly used which are inefficient. Today fluorescent fixtures are mostly used with PV's due to its high efficacy. Light-emitting diodes present a new vision to energy efficiency in lighting design with their low energy consumption. Current research predicts improved efficiencies of LED light fixtures and their commercial use is a few years away. LEDs which operate on DC voltages when coupled with photovoltaics can be a simple PV lighting application and a sustainable solution with potential for payback. This research evaluates the design and construction of a photovoltaic DC LED lighting system for a solar house at Pennsylvania State University. A detailed cost and payback analysis of a PV DC LED lighting system is presented in this research. PV output simulations for the solar house are presented. Results presented in this research indicate that the Solid state lighting market is evolving rapidly and that LED's are a choice in stand-alone photovoltaic DC lighting systems. The efficiency and the cost-effectiveness of such systems would however improve in the coming years with research and development now focused on PV systems and on Solid state lighting technologies.

  3. [Which colours can we hear?: light stimulation of the hearing system].

    Science.gov (United States)

    Wenzel, G I; Lenarz, T; Schick, B

    2014-02-01

    The success of conventional hearing aids and electrical auditory prostheses for hearing impaired patients is still limited in noisy environments and for sounds more complex than speech (e. g. music). This is partially due to the difficulty of frequency-specific activation of the auditory system using these devices. Stimulation of the auditory system using light pulses represents an alternative to mechanical and electrical stimulation. Light is a source of energy that can be very exactly focused and applied with little scattering, thus offering perspectives for optimal activation of the auditory system. Studies investigating light stimulation of sectors along the auditory pathway have shown stimulation of the auditory system is possible using light pulses. However, further studies and developments are needed before a new generation of light stimulation-based auditory prostheses can be made available for clinical application.

  4. An empirical study on energy efficiency improvement through photovoltaic systems and a LED lighting control system

    Science.gov (United States)

    Choi, Young Kwan; Lee, Jae Hyeong

    2015-09-01

    In this research, a facility was constructed and its performance was analyzed to improve the energy efficiency of a vertical-type water treatment building. After the design and construction of a fixed tilt Photovoltaic in Building (PVIB) on the rooftop using a crystalline silicon solar cell module and photovoltaic generator integrated with the building by using a Building Integrated Photovoltaic System (BIPV), a thin-film module on the rooftop and outer wall of water treatment building, and the generation efficiency was analyzed. Also, a DC distribution was established for use of a brushless DC (BLDC) pump motor, and the existing lighting-facility-based manual on-off method was turned into a system for energy conservation by controlling light emitting diode (LED) through a wireless motion sensor and dimming control. In addition, a Building Energy Management System (BEMS) for a real-time analysis of the energy efficiency for a vertical0type water treatment building was prepared and tested. The vertical-type water treatment building developed in this study is currently operating the BEMS. The vertical-type water treatment building reported in this paper is expected to reduce energy consumption by about 30% compared to existing water treatment systems.

  5. GATEWAY Demonstrations: Tuning the Light in Senior Care: Evaluating a Trial LED Lighting System at the ACC Care Center in Sacramento, CA

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Robert G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wilkerson, Andrea M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Samla, Connie [Sacramento Municipal Utility District, Sacramento, CA (United States); Bisbee, Dave [Sacramento Municipal Utility District, Sacramento, CA (United States)

    2016-08-31

    The GATEWAY program documented the performance of tunable-white LED lighting systems installed in several spaces within the ACC Care Center, a senior-care facility in Sacramento, CA. The project results included energy savings and improved lighting quality, as well as other possible health-related benefits that may have been attributable, at least in part, to the lighting changes.

  6. Violet-blue LEDs based on p-GaN/n-ZnO nanorods and their stability.

    Science.gov (United States)

    Jha, Shrawan; Qian, Jin-Cheng; Kutsay, Oleksandr; Kovac, Jaroslav; Luan, Chun-Yan; Zapien, Juan Antonio; Zhang, Wenjun; Lee, Shuit-Tong; Bello, Igor

    2011-06-17

    In this paper, we report a fabrication, characterization and stability study of p-GaN/n-ZnO nanorod heterojunction light-emitting devices (LEDs). The LEDs were assembled from arrays of n-ZnO vertical nanorods epitaxially grown on p-GaN. LEDs showed bright electroluminescence in blue (440 nm), although weaker violet (372 nm) and green-yellow (550 nm) spectral components were also observed. The device characteristics are generally stable and reproducible. The LEDs have a low turn-on voltage (∼5 V). The electroluminescence (EL) is intense enough to be noticed by the naked eye, at an injection current as low as ∼ 40 µA (2.1 × 10(-2) A cm(-2) at 7 V bias). Analysis of the materials, electrical and EL investigations point to the role of a high quality of p-n nano-heterojunction which facilitates a large rectification ratio (320) and a stable reverse current of 2.8 µA (1.4 × 10(-3) A cm(-2) at 5 V). Stability of EL characteristics was investigated in detail. EL intensity showed systematic degradation over a short duration when the LED was bias-stressed at 30 V. At smaller bias (LEDs tend to show a stable and repeatable EL characteristic. Thus a simple low temperature solution growth method was successfully exploited to realize nanorod/film heterojunction LED devices with predictable characteristics.

  7. UV-visible detector and LED based n-ZnO/p-Si heterojunction formed by electrodeposition

    Directory of Open Access Journals (Sweden)

    A. Baltakesmez

    2013-03-01

    Full Text Available In this study, we have investigated the heterojunctions formed by n-ZnO thin films deposited on (100 p-Si:B using electrochemical deposition (ECD technique. Structural, electrical and luminescence features of the thin films were respectively measured. Optimal sets of growth conditions seem to be the ones that are undergone for the samples D1 and D2. It was observed that n-ZnO thin films have dominantly preferred orientation of (002. It has been shown that the heterostructures exhibited reasonable rectifying behavior with turn-on voltage of about 1.2 V and ideality factor of 2.1. In case of illumination with 400 nm wavelength light, significant increase occurred especially in reverse bias current by a factor of 103 and 102 for the D1 and the D2, respectively. Bandgap of ZnO thin films has been determined to be 3.4 eV at the room temperature by using the band edge photoluminescence measurements. Finally, the room temperature electroluminescence (EL results show that the heterostructures exhibits observable broad luminescence centered at the wavelengths of 390 and 510 nm for D1 and 470 nm for D2, respectively. Additionally, sharp lasing peaks are also observed in the EL spectra, probably due to the multiple scattering effects.

  8. Illumination performance and energy saving of a solar fiber optic lighting system.

    Science.gov (United States)

    Lingfors, David; Volotinen, Tarja

    2013-07-01

    The illumination performance and energy savings of a solar fiber optic lighting system have been verified in a study hall--corridor interior. The system provides intensive white light with a high luminous flux of 4500 lm under 130000 lx direct sun radiation at a 10 m fiber distance from the sun-tracking light collector. The color temperature that describes the light color perceived is 5800 ± 300 K, i.e. close to the direct sunlight outside, and the color rendering index (86), that describes how well colors are rendered under the light source, is higher for the solar lights than for the supplementary fluorescent lights (77). Thus this high quality solar lighting improves the visibility of all kinds of objects compared to the fluorescent lights. Annual lighting energy savings of 19% in Uppsala, Sweden and 46% in southern Europe were estimated for a study hall interior, as well as 27% and 55% respectively in an interior illuminated 16 h per day all days of a year.

  9. Dynamic miniature lighting system with low correlated colour temperature and high colour rendering index for museum lighting of fragile artefacts

    DEFF Research Database (Denmark)

    Thorseth, Anders; Corell, Dennis Dan; Poulsen, Peter Behrensdorff

    2013-01-01

    Illumination of fragile and irreplaceable historical objects exhibited to the public presents challenges with regards to: good colour rendering, low photochemical degradation of sensitive materials and general energy consumption. We present a dynamic tri-colour LED lighting system for illumination...... of historical artefacts in display cases at museums and other exhibitions, which can replace 3-5 Watt incandescent light bulbs with a correlated colour temperature (CCT) from 2000 K to 2400 K. The solution decreases the energy consumption by up to 80 %, while maintaining colour rendering indices (Ra) above 90...... and important special colour rendering indices R9 between 50 and 90, while decreasing the level of harmful short wavelength radiation by between 20 - 30 %....

  10. Study for standardization of the lighting system in fruit sorting

    Science.gov (United States)

    Gomes, J. F. S.; Baldner, F. O.; Costa, P. B.; Guedes, M. B.; Oliveira, I. A. A.; Leta, F. R.

    2016-07-01

    Sorting is a very important step in the fruit processing. The attributes definition and characterization are important for both marketing and end user, making it necessary to establish regulations for classification and standardization in order to unify the language of the market and enabling a more efficient market and also increase consumer awareness. For this end, it is necessary to standardize the technical criteria that can change the perception of the product. Studies have been developed in order to standardize a methodology to determine the subclass of fruit ripening, evaluating the influence of different light sources in the subclass evaluation.

  11. Designing High Efficient Solar Powered OLED Lighting Systems

    DEFF Research Database (Denmark)

    Ploug, Rasmus Overgaard; Poulsen, Peter Behrensdorff; Thorsteinsson, Sune

    2016-01-01

    for the 10 Wp version. Furthermore, we present measurements of state-of-the-art commercial available OLED with regards to the luminous flux, luminous efficacy, luminance homogeneity, temperature dependency and IV characteristic of the OLED panels. In addition, solar powered OLED product concepts are proposed.......OLEDs used in solar powered lighting applications is a market of the future. This paper reports the development of electronic Three-Port-Converters for PV OLED product integration in the low-power area respectively for 1-10 Wp and 10-50 Wp with a peak efficiency of 97% at 1.8 W of PV power...

  12. Anisotropic light emissions in luminescent solar concentrators-isotropic systems.

    Science.gov (United States)

    Verbunt, Paul P C; Sánchez-Somolinos, Carlos; Broer, Dirk J; Debije, Michael G

    2013-05-06

    In this paper we develop a model to describe the emission profile from randomly oriented dichroic dye molecules in a luminescent solar concentrator (LSC) waveguide as a function of incoming light direction. The resulting emission is non-isotropic, in contradiction to what is used in almost all previous simulations on the performance of LSCs, and helps explain the large surface losses measured in these devices. To achieve more precise LSC performance simulations we suggest that the dichroic nature of the dyes must be included in the future modeling efforts.

  13. Designing High Efficient Solar Powered OLED Lighting Systems

    DEFF Research Database (Denmark)

    Ploug, Rasmus Overgaard; Poulsen, Peter Behrensdorff; Thorsteinsson, Sune

    2016-01-01

    OLEDs used in solar powered lighting applications is a market of the future. This paper reports the development of electronic Three-Port-Converters for PV OLED product integration in the low-power area respectively for 1-10 Wp and 10-50 Wp with a peak efficiency of 97% at 1.8 W of PV power...... for the 10 Wp version. Furthermore, we present measurements of state-of-the-art commercial available OLED with regards to the luminous flux, luminous efficacy, luminance homogeneity, temperature dependency and IV characteristic of the OLED panels. In addition, solar powered OLED product concepts are proposed....

  14. Optimal traffic light control method for a single intersection based on hybrid systems

    Institute of Scientific and Technical Information of China (English)

    赵晓华; 陈阳舟; 崔平远

    2003-01-01

    A single intersection of two phases is selected as a model to put forward a new optimal time-planning scheme for traffic light based on the model of hybrid automata for single intersection. A method of optimization is proposed for hybrid systems, and the average queue length over all queues is used as an objective function to find an optimal switching scheme for traffic light. It is illustrated that traffic light control for single intersection is a typical hybrid system, and the optimal planning-time scheme can be obtained using the optimal hybrid systems control based on the two stages method.

  15. Fidelity of quantum state for interacting system of light field and atomic Bose-Einstein condensate

    Institute of Scientific and Technical Information of China (English)

    Chunjia Huang; Ming Zhou; Fanzhi Kong; Jiayuan Fang; Kewei Mo

    2005-01-01

    @@ The evolution characteristics of quantum state fidelity in an interacting system of single-mode light field and atomic Bose-Einstein condensate have been studied and the influence of the initial light field intensity and the interaction among atoms of Bose-Einstein condensate on the quantum state fidelity respectively have been discussed.

  16. Investing in Their Future: Portland’s Purchase and Conversion of an LED Street Lighting System

    Energy Technology Data Exchange (ETDEWEB)

    Kinzey, B. R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rosinbum, T. [Portland Bureau of Transportation, Portland, OR (United States)

    2015-08-28

    During the ongoing process of converting its streetlights from high-pressure sodium to LED, the city of Portland, Oregon, purchased a large portion of its street lighting system and encountered a range of issues among the stakeholders. This report identifies some of the challenges involved and discusses how they were addressed, in order to help inform and facilitate future lighting transitions elsewhere.

  17. Proposal for an Experimental Methodology for Evaluation of Natural Lighting Systems Applied in Buildings

    Directory of Open Access Journals (Sweden)

    Anderson Diogo Spacek

    2017-07-01

    Full Text Available This work has the objective of developing a methodology for the evaluation of indoor natural lighting systems, which, with speed and practicality, provides from real conditions of use a reliable result about the quality and performance of the proposed system. The methodology is based on the construction of two real-size test environments, which will be subjected to a natural light system through reflexive tubes made from recycled material, and to a commercial system already certified and consolidated, creating the possibility of comparison. Furthermore, the data acquired in the test environments will be examined in light of the values of solar radiation obtained from a digital meteorological station, such that it is possible to stipulate the lighting capacity of the systems at different times of the year.

  18. Computer Modeling of Daylight-Integrated Photocontrol of Electric Lighting Systems

    Directory of Open Access Journals (Sweden)

    Richard Mistrick

    2015-05-01

    Full Text Available This article presents a variety of different approaches to both model and assess the performance of daylight-integrated electric lighting control systems. In these systems, the output of a controlled lighting zone is based on a light sensor reading and a calibrated control algorithm. Computer simulations can consider the simulated illuminance data generated from both the electric lighting system and a daylight delivery system whose performance is addressed using typical meteorological year (TMY weather data. Photosensor signals and the operation of a control system’s dimming algorithms are also included. Methods and metrics for evaluating simulated performance for the purpose of making informed design decisions that lead to the best possible installed system performance are presented.

  19. Space Object and Light Attribute Rendering (SOLAR) Projection System

    Science.gov (United States)

    2017-05-08

    systems operating in the visual spectrum. It is a cost effective way to rapidly validate algorithms and imaging systems and establishes a systematic...carried out. Primary demonstrations included the projection of a start field and the visual identification of stars. • December 2016: The SOLAR system...to undergraduate research, Prof. Majji and Prof. Singla currently teach a special class on the design and development of UAVs, tracking systems and

  20. Measured Off-Grid LED Lighting System Performance

    Energy Technology Data Exchange (ETDEWEB)

    Granderson, Jessica; Galvin, James; Bolotov, Dmitriy; Clear, Robert; Jacobson, Arne; Mills, Evan

    2008-12-18

    This report is a product of our ongoing effort to support the development of high-quality yet affordable products for off-grid lighting in the developing world that have good potential to succeed in the market. The effort includes work to develop low-cost testing procedures, to identify useful performance metrics, and to facilitate the development of industry standards and product rating protocols. We conducted laboratory testing of nine distinct product lines. In some cases we also tested multiple generations of a single product line and/or operating modes for a product. The resultsare summarized in Table 1. We found that power consumption and light output varied by nearly a factor of 12, with efficacy varying by a factor of more than six. Of particular note, overall luminous efficacy varied from 8.2 to 53.1 lumens per watt. Color quality indices variedmaterially, especially for correlated color temperature. Maximum illuminance, beamcandlepower, and luminance varied by 8x, 32x, and 61x respectively, suggesting considerable differences among products in terms of service levels and visual comfort. Glare varied by1.4x, and was above acceptable thresholds in most cases. Optical losses play a role in overall performance, varying by a factor of 3.2 and ranging as high as 24percent. These findings collectively indicate considerable potential for improved product design.

  1. Light Emitting, Photovoltaic or Other Electronic Apparatus and System

    Science.gov (United States)

    Ray, William Johnstone (Inventor); Lowenthal, Mark D. (Inventor); Shotton, Neil O. (Inventor); Blanchard, Richard A. (Inventor); Lewandowski, Mark Allan (Inventor); Fuller, Kirk A. (Inventor); Frazier, Donald Odell (Inventor)

    2016-01-01

    The present invention provides an electronic apparatus, such as a lighting device comprised of light emitting diodes (LEDs) or a power generating apparatus comprising photovoltaic diodes, which may be created through a printing process, using a semiconductor or other substrate particle ink or suspension and using a lens particle ink or suspension. An exemplary apparatus comprises a base; at least one first conductor; a plurality of diodes coupled to the at least one first conductor; at least one second conductor coupled to the plurality of diodes; and a plurality of lenses suspended in a polymer deposited or attached over the diodes. The lenses and the suspending polymer have different indices of refraction. In some embodiments, the lenses and diodes are substantially spherical, and have a ratio of mean diameters or lengths between about 10:1 and 2:1. The diodes may be LEDs or photovoltaic diodes, and in some embodiments, have a junction formed at least partially as a hemispherical shell or cap.

  2. Selective mapping and restorable clipping joint scheme for light-emitting diode nonlinearity alleviation in visible light communication system

    Science.gov (United States)

    Yan, Chaowen; Wang, Jianping; Lu, Huimin; Shi, Yinjia; Zhang, Yini

    2016-05-01

    A joint algorithm, integrating selective mapping (SLM) and restorable clipping (RC), is proposed for the direct current-biased optical orthogonal frequency division multiplexing (DCO-OFDM) and visible light communication (VLC) system to reduce the nonlinearity impacts of light-emitting diode (LED) aggravated by high peak-to-average power ratio (PAPR) and DC-bias. The performance of DCO-OFDM VLC system is analyzed and discussed with different techniques of LED nonlinearity alleviation. The simulation results show that compared to the original DCO-OFDM VLC system, the system with the proposed scheme can achieve about 4.8 dB improvement of PAPR reduction and 7 dB improvement of bit error rate (BER) performance. The reason is that the signals acquiring the desired shape in LED linear region can be recovered correctly without distortion induced by LED nonlinearity. It is demonstrated that the proposed SLM-RC technique effectively reduces not only PAPR but also the impacts of LED nonlinearity without BER deterioration.

  3. Photovoltaic OLED Driver for Low-Power Stand-Alone Light-to-Light Systems

    DEFF Research Database (Denmark)

    Ploug, Rasmus Overgaard; Knott, Arnold

    2016-01-01

    Photovoltaic (PV) stand-alone systems need to achieve multiple energy conversion modes. I.e. the energy conversion from PV to a local energy storage as well as energy conversion from the energy storage to the load. This paper documents the practical design considerations for the development of a ...... conversion from photovoltaic panel to the battery, and 97 % in the area 1.4 W to 2 W for power delivery to the OLED....

  4. Simulation of multicomponent light source for optical-electronic system of color analysis objects

    Science.gov (United States)

    Peretiagin, Vladimir S.; Alekhin, Artem A.; Korotaev, Valery V.

    2016-04-01

    Development of lighting technology has led to possibility of using LEDs in the specialized devices for outdoor, industrial (decorative and accent) and domestic lighting. In addition, LEDs and devices based on them are widely used for solving particular problems. For example, the LED devices are widely used for lighting of vegetables and fruit (for their sorting or growing), textile products (for the control of its quality), minerals (for their sorting), etc. Causes of active introduction LED technology in different systems, including optical-electronic devices and systems, are a large choice of emission color and LED structure, that defines the spatial, power, thermal and other parameters. Furthermore, multi-element and color devices of lighting with adjustable illumination properties can be designed and implemented by using LEDs. However, devices based on LEDs require more attention if you want to provide a certain nature of the energy or color distribution at all the work area (area of analysis or observation) or surface of the object. This paper is proposed a method of theoretical modeling of the lighting devices. The authors present the models of RGB multicomponent light source applied to optical-electronic system for the color analysis of mineral objects. The possibility of formation the uniform and homogeneous on energy and color illumination of the work area for this system is presented. Also authors showed how parameters and characteristics of optical radiation receiver (by optical-electronic system) affect on the energy, spatial, spectral and colorimetric properties of a multicomponent light source.

  5. Deducing effective light transport parameters in optically thin systems

    CERN Document Server

    Mazzamuto, Giacomo; Toninelli, Costanza; Wiersma, Diederik

    2015-01-01

    We present an extensive Monte Carlo study on light transport in optically thin slabs, addressing both axial and transverse propagation. We completely characterize the so-called ballistic-to-diffusive transition, notably in terms of the spatial variance of the transmitted/reflected profile. We test the validity of the prediction cast by diffusion theory, that the spatial variance should grow independently of absorption and, to a first approximation, of the sample thickness and refractive index contrast. Based on a large set of simulated data, we build a freely available look-up table routine allowing reliable and precise determination of the microscopic transport parameters starting from robust observables which are independent of absolute intensity measurements. We also present the Monte Carlo software package that was developed for the purpose of this study.

  6. Optimized Design of LED Daylight Lamp Lighting System

    Institute of Scientific and Technical Information of China (English)

    TIAN Da-lei; GUAN Rong-feng; WANG Xing

    2008-01-01

    In order to meet the requirements of indoor illumination, a LED daylight lamp model was designed, it can replace traditional fluorescent lamp without insteading additional power supply establishment. The optical properties of the model were simulated using optical analysis software. Its luminous efficiency is about 30.4 lm/W, and the illuminance is about 38 lux when the distance is 1.5 m between the center of the model and measured spot. With the theoretically-optimized design of LED model, experiments based on the results of the optimal simulation in the laboratory were conducted to verify the performance of the proposed LED model, it reaches a power factor of about 0.8 at 6 W. The simulation results are very similar with the measured values. It is testified that simulative method is one of the effective tools for LED lighting optical design.

  7. Automatic Boat Identification System for VIIRS Low Light Imaging Data

    Directory of Open Access Journals (Sweden)

    Christopher D. Elvidge

    2015-03-01

    Full Text Available The ability for satellite sensors to detect lit fishing boats has been known since the 1970s. However, the use of the observations has been limited by the lack of an automatic algorithm for reporting the location and brightness of offshore lighting features arising from boats. An examination of lit fishing boat features in Visible Infrared Imaging Radiometer Suite (VIIRS day/night band (DNB data indicates that the features are essentially spikes. We have developed a set of algorithms for automatic detection of spikes and characterization of the sharpness of spike features. A spike detection algorithm generates a list of candidate boat detections. A second algorithm measures the height of the spikes for the discard of ionospheric energetic particle detections and to rate boat detections as either strong or weak. A sharpness index is used to label boat detections that appear blurry due to the scattering of light by clouds. The candidate spikes are then filtered to remove features on land and gas flares. A validation study conducted using analyst selected boat detections found the automatic algorithm detected 99.3% of the reference pixel set. VIIRS boat detection data can provide fishery agencies with up-to-date information of fishing boat activity and changes in this activity in response to new regulations and enforcement regimes. The data can provide indications of illegal fishing activity in restricted areas and incursions across Exclusive Economic Zone (EEZ boundaries. VIIRS boat detections occur widely offshore from East and Southeast Asia, South America and several other regions.

  8. Membrane systems for energy efficient separation of light gases

    Energy Technology Data Exchange (ETDEWEB)

    Devlin, D.J.; Archuleta, T.; Barbero, R. [Los Alamos National Lab., NM (United States)] [and others

    1997-04-01

    Ethylene and propylene are two of the largest commodity chemicals in the United States and are major building blocks for the petrochemicals industry. These olefins are separated currently by cryogenic distillation which demands extremely low temperatures and high pressures. Over 75 billion pounds of ethylene and propylene are distilled annually in the US at an estimated energy requirement of 400 trillion BTU`s. Non-domestic olefin producers are rapidly constructing state-of-the-art plants. These energy-efficient plants are competing with an aging United States olefins industry in which 75% of the olefins producers are practicing technology that is over twenty years old. New separation opportunities are therefore needed to continually reduce energy consumption and remain competitive. Amoco has been a leader in incorporating new separation technology into its olefins facilities and has been aggressively pursuing non-cryogenic alternatives to light gas separations. The largest area for energy reduction is the cryogenic isolation of the product hydrocarbons from the reaction by-products, methane and hydrogen. This separation requires temperatures as low as {minus}150{degrees}F and pressures exceeding 450 psig. This CRADA will focus on developing a capillary condensation process to separate olefinic mixtures from light gas byproducts at temperatures that approach ambient conditions and at pressures less than 250 psig; this technology breakthrough will result in substantial energy savings. The key technical hurdle in the development of this novel separation concept is the precise control of the pore structure of membrane materials. These materials must contain specially-shaped channels in the 20-40A range to provide the driving force necessary to remove the condensed hydrocarbon products. In this project, Amoco is the technology end-user and provides the commercialization opportunity and engineering support.

  9. Industrial lighting system. For a global cost approach of an industrial lighting system installation; Eclairage industriel. Pour une approche en cout global d'une installation d'eclairage industriel

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-01

    This booklet presents the interest of a performant industrial lighting system in term of energy and cost conservation, working conditions and safety. A calculation method integrating the various parameters of the lighting system, technical specifications of lamps and regulations are given to help the industrialists in the choice of a performant lighting system. (A.L.B.)

  10. Self-Assembled PDINH Supramolecular System for Photocatalysis under Visible Light.

    Science.gov (United States)

    Liu, Di; Wang, Jun; Bai, Xiaojuan; Zong, Ruilong; Zhu, Yongfa

    2016-09-01

    A self-assembled perylene-3,4,9,10-tetracarboxylic diimide(PDINH) supramolecular system consisting of all-organic PDINH molecule building blocks through non-covalent interactions works as a visible light photocatalyst with high activity.

  11. Nonreciprocity light propagation in coupled microcavities system beyond weak-excitation approximation

    CERN Document Server

    Zheng, A S; Chen, H; Mei, T; Liu, J

    2016-01-01

    We propose an alternative scheme for nonreciprocal light propagation in two coupled cavities system, in which a two-level quantum emitter is coupled to one of the optical microcavities. For the case of parity-time (\\textrm{PT}) system (i.e., active-passive coupled cavities system), the cavity gain can significantly enhance the optical nonlinearity induced by the interaction between a quantum emitter and cavity field beyond weak-excitation approximation. The giant optical nonlinearity results in the non-lossy nonreciprocal light propagation with high isolation ratio in proper parameters range. In addition, our calculations show that nonreciprocal light propagation will not be affected by the unstable output field intensity caused by optical bistability and we can even switch directions of nonreciprocal light propagation by appropriately adjusting the system parameters.

  12. A high-performance stand-alone solar PV power system for LED lighting

    KAUST Repository

    Huang, B. J.

    2010-06-01

    The present study developed a high-performance solar PV power technology for the LED lighting of a solar home system. The nMPPO (near-Maximum-Power- Point- Operation) design is employed in system design to eliminate MPPT. A feedback control system using pulse width modulation (PWM) technique was developed for battery charging control which can increase the charging capacity by 78%. For high-efficiency lighting, the LED is directly driven by battery using a PWM discharge control to eliminate a DC/DC converter. Two solar-powered LED lighting systems (50W and 100W LED) were built. The long-term outdoor tests have shown that the loss of load probability for full-night lighting requirement is zero for 50W LED and 3.6% for 100W LED. © 2010 IEEE.

  13. A holographic display system based on DMD using LED as light source

    Science.gov (United States)

    Su, Ping; Cheng, Bingchao; Cao, Wenbo; Ma, Jianshe; Cao, Liangcai

    2016-09-01

    Digital Micro-mirror Device (DMD) is an important tool in holographic display owning high-speed refresh rate and good diffraction efficiency. However, the reconstruction light source has great impact to image quality. A new holographic display system based on DMD for using light-emitting diodes (LEDs), is proposed in this paper. LEDs are chosen as light source to replace the laser, since it can reduce the speckle noise effectively, which is caused by both temporal and spatial coherence of laser. In order to solve the problem using LED as DMD holographic display light source, the characteristics of DMD as the display device for holographic displays are studied. An aspheric collimator for LED is used to improve the optical efficiency. A spatial filter is used to improve the coherence. The experimental results show that this lighting system has a good display quality.

  14. Monte Carlo analysis of a control technique for a tunable white lighting system

    DEFF Research Database (Denmark)

    Chakrabarti, Maumita; Thorseth, Anders; Jepsen, Jørgen

    2017-01-01

    A simulated colour control mechanism for a multi-coloured LED lighting system is presented. The system achieves adjustable and stable white light output and allows for system-to-system reproducibility after application of the control mechanism. The control unit works using a pre-calibrated lookup...... table for an experimentally realized system, with a calibrated tristimulus colour sensor. A Monte Carlo simulation is used to examine the system performance concerning the variation of luminous flux and chromaticity of the light output. The inputs to the Monte Carlo simulation, are variations of the LED...... peak wavelength, the LED rated luminous flux bin, the influence of the operating conditions, ambient temperature, driving current, and the spectral response of the colour sensor. The system performance is investigated by evaluating the outputs from the Monte Carlo simulation. The outputs show...

  15. Monte Carlo analysis of a control technique for a tunable white lighting system

    DEFF Research Database (Denmark)

    Chakrabarti, Maumita; Thorseth, Anders; Jepsen, Jørgen

    2017-01-01

    A simulated colour control mechanism for a multi-coloured LED lighting system is presented. The system achieves adjustable and stable white light output and allows for system-to-system reproducibility after application of the control mechanism. The control unit works using a pre-calibrated lookup...... table for an experimentally realized system, with a calibrated tristimulus colour sensor. A Monte Carlo simulation is used to examine the system performance concerning the variation of luminous flux and chromaticity of the light output. The inputs to the Monte Carlo simulation, are variations of the LED...... peak wavelength, the LED rated luminous flux bin, the influence of the operating conditions, ambient temperature, driving current, and the spectral response of the colour sensor. The system performance is investigated by evaluating the outputs from the Monte Carlo simulation. The outputs show...

  16. A Fine-Grained Visible Light Communication Position Detection System Embedded in One-Colored Light Using DMD Projector

    Directory of Open Access Journals (Sweden)

    Motoi Kodama

    2017-01-01

    Full Text Available When we consider the Internet of Things (IoT society that all of the people and things are connected by the Internet and with each other and they can use the variety of services and applications, the development of sensing and communication technology is very important. As one of its key technologies, the visible light communication (VLC has attracted attention in the point of ubiquity. In this paper, we propose a fine-grained VLC position detection system embedded in one-colored light using Digital Micromirror Device (DMD projector for new location services in millimeters and report its concept and fundamental experiment using our prototype of the receiver module with Linux single-board computer, Raspberry Pi. In addition, we mention the future application using our system in a clothes shop. Our experimental results show that our system has high accuracy in millimeters and the potential to be more convenient in the future’s location services using the VLC with the DMD projector. There was no trial to use a DMD projector as the illumination until now, but our study shows that the DMD projector has an availability of special modulated VLC illumination type beacon in the IoT age.

  17. Light-to-light readout system of the CMS electromagnetic calorimeter

    CERN Document Server

    Denes, P; Lustermann, W; Mathez, H; Pangaud, P; Walder, J P

    2001-01-01

    For the CMS experiment at the Large Hadron Collider at CERN, an 8OOOO-crysral electromagnetic calorimeter will measure electron and photon energies with high precision over a dynamic range of roughly 16 bits. The readout electronics will be located directly behind the crystals, and must survive a total dose of up to 2x10 Gy along with 5x10**1**3 n/cm**2. A readout chain consisting of a custom wide-range acquisition circuit, commercial ADC and custom optical link for each crystal is presently under construction. An overview of the design is presented, with emphasis on the large-scale fiber communication system. 11 Refs.

  18. Design of Solar Optical Fiber Lighting System for Enhanced Lighting in Highway Tunnel Threshold Zone: A Case Study of Huashuyan Tunnel in China

    Directory of Open Access Journals (Sweden)

    Xiaochun Qin

    2015-01-01

    Full Text Available In this paper, the principle, structural composition, materials, and characteristics of solar optical fiber lighting system were discussed. The different luminance requirements of different zones of highway tunnel were identified on the basis of the analysis of tunnel lighting considering drivers’ visually self-accommodating physiological function for luminance change. Taken Huashuyan Tunnel of G109 Highway located in Hohhot of Inner Mongolia in China as the case study, the system design of solar optical fiber lighting for enhanced lighting in threshold zone of highway tunnel was made. It was indicated through calculation that the design length of solar optical fiber enhanced lighting was related to the design speed, longitudinal slope, and overhead clearance of the tunnel, and the design luminance of solar optical fiber enhanced lighting was related to the luminance outside the tunnel, the design speed, and the design traffic flow of the tunnel. Luminance analysis of the solar optical fiber lighting system of Huashuyan Tunnel was made based on the on-site experiment. Also, the 3D illuminance simulation results by DIALux software were made to indicate that the solar optical fiber lighting system in Huashuyan Tunnel still well met the enhanced lighting demand even not considering the contribution of LED lighting.

  19. Visible-Light Tomography Using an Optical Imaging-System

    NARCIS (Netherlands)

    Ingesson, L. C.; Koning, J. J.; Donne, A. J. H.; D.C. Schram,

    1992-01-01

    A system for tomography in the wavelength range 200-1 100 nm has been designed for the Rijnhuizen Tokamak Project (RTP). The plasma is viewed from five directions in one poloidal plane with a total of 80 detectors. An optical imaging system consisting of two spherical mirrors for each viewing direct

  20. Can pulsed xenon ultraviolet light systems disinfect aerobic bacteria in the absence of manual disinfection?

    Science.gov (United States)

    Jinadatha, Chetan; Villamaria, Frank C; Ganachari-Mallappa, Nagaraja; Brown, Donna S; Liao, I-Chia; Stock, Eileen M; Copeland, Laurel A; Zeber, John E

    2015-04-01

    Whereas pulsed xenon-based ultraviolet light no-touch disinfection systems are being increasingly used for room disinfection after patient discharge with manual cleaning, their effectiveness in the absence of manual disinfection has not been previously evaluated. Our study indicates that pulsed xenon-based ultraviolet light systems effectively reduce aerobic bacteria in the absence of manual disinfection. These data are important for hospitals planning to adopt this technology as adjunct to routine manual disinfection. Published by Elsevier Inc.

  1. 3D Wide FOV Scanning Measurement System Based on Multiline Structured-Light Sensors

    OpenAIRE

    2014-01-01

    Structured-light three-dimensional (3D) vision measurement is currently one of the most common approaches to obtain 3D surface data. However, the existing structured-light scanning measurement systems are primarily constructed on the basis of single sensor, which inevitably generates three obvious problems: limited measurement range, blind measurement area, and low scanning efficiency. To solve these problems, we developed a novel 3D wide FOV scanning measurement system which adopted two mult...

  2. High-performance AlGaInP light-emitting diodes

    Science.gov (United States)

    Maranowski, Steven A.; Camras, Michael D.; Chen, Changhua; Cook, Lou W.; Craford, M. G.; DeFevere, Dennis C.; Fletcher, Robert M.; Hofler, Gloria E.; Kish, Frederick A.; Kuo, Chihping; Moll, A. J.; Osentowski, Tim; Park, K. G.; Peanasky, Michael J.; Rudaz, S. L.; Steigerwald, Dan A.; Steranka, Frank M.; Stockman, Steve A.; Tan, I. H.; Tarn, J.; Yu, Jingxi; Ludowise, Mike J.; Robbins, Virginia M.

    1997-04-01

    A new class of LEDs based on the AlGaInP material system first became commercially available in the early 1990's. These devices benefit from a direct bandgap from the red to the yellow-green portion of the spectrum. The high efficiencies possible in AlGaInP across this spectrum have enabled new applications for LEDs including automotive lighting, outdoor variable message signs, outdoor large screen video displays, and traffic signal lights. A review of high-brightness AlGaInP LED technology will be presented.

  3. Designing Dual-Active Bridge (DAB) converter for energy storage/recovery systems in a lighting smart grid context

    OpenAIRE

    Rico Secades, Manuel; García Llera, Daniel; López Corominas, Emilio Ramón; Calleja Rodríguez, Antonio Javier

    2014-01-01

    Lighting Systems are suffering and important evolution with the introduction of LED lighting systems with new strategies of energy savings, incorporation of renewable energy sources and optionally a bidirectional interconnection with the mains (AC grid or DC interconnection bus). Lighting Systems are moving to Lighting Smart Grids and step by step integrating in Smart City strategies. In this context design of modular and efficient energy storage/recovery systems are gaining importance lookin...

  4. Real Time Superresolution by Means of an Ultrasonic Light Diffractor and TV System.

    Science.gov (United States)

    Sato, T; Ueda, M; Ikeda, T

    1974-06-01

    The change of angle and the shift of frequency of light by an ultrasonic light diffractor are used for real time realization of a holographic superresolution system. A TV system and an electrical filter are used to pick up the desired image hologram from the superposed, images, which are obtained by a number of object-beam lights and reference beams. For two-dimensional as well as one-dimensional objects, images superresolved three to five times are displayed on a TV monitor in real time.

  5. Advanced optical design and control of multi-colored SSL system for stage lighting application

    DEFF Research Database (Denmark)

    Chakrabarti, Maumita

    mixing system and provides a solution which is capable of replacing both the Fresnel lens spotlight Halogen lamp (2kW) and the commercially available LED luminaire (~160W), which have applications in stage lighting, theater lighting, TV studio lighting, etc. Since the optical design comprises LEDs...... in wavelength for a laser color mixing system can be detected by a new speckle based wavemeter, which is easy for use and cost‐effective compared to the commercially available expensive spectrometers. The thesis also reports on the fabrication of a tool for replicating the microlens structure used for beam...

  6. Experimental investigation of slow light propagation in degenerate two-level system

    Institute of Scientific and Technical Information of China (English)

    Wang Li-Rong; Zhao Yan-Ting; Ma Jie; Zhao Jian-Ming; Xiao Lian-Tuan; Jia Suo-Tang

    2006-01-01

    Slowing a light pulse in a degenerate two-level system is observed with a double-frequency sweeping technique. The effects of coupling beam intensity, cell temperature and frequency detunings of the coupling and probe beams in resonance, on the slowing of light propagation in such a system are investigated. It is found that group velocities depend strongly on polarization combinations. A group velocity υg=6760m/s of light pulses in caesium vapour is obtained under the optimal parameters.

  7. Photometric Observation and Light Curve Analysis of Binary System ER-Orionis

    Indian Academy of Sciences (India)

    M. M. Lame’e; B. Javanmardi; N. Riazi

    2010-06-01

    Photometric observations of the over-contact binary ER ORI were performed during November 2007 and February to April 2008 with the 51 cm telescope of Biruni Observatory of Shiraz University in U, B and V filters (Johnson system) and an RCA 4509 photomultiplier. We used these data to obtain the light curves and calculate the newtimes of minimum light in each filter and plot the O–C diagram of ER ORI. Using the Wilson’s computer code with the help of an auxiliary computer program to improve the optimizations, the light curve analyses were carried out to find out the photometric elements of the system.

  8. Performance Indexes Assessment for Lighting Systems Based on the Normalized Power Density and Energy Losses Estimation in University Workrooms

    OpenAIRE

    2015-01-01

    Well-designed lighting decreases accidents and diseases of eyes and can increase productivity and concentration. Increase of energy price and a high proportion of electric lighting energy consumption in buildings due to defects in designing and maintenance led to desirable lighting to be reduced. One of our challenges in providing health and quality of lighting is lack of economic justification of projects. Furthermore, evaluating the lighting systems is very important to improve these system...

  9. Amplification without inversion, fast light and optical bistability in a duplicated two-level system

    Energy Technology Data Exchange (ETDEWEB)

    Ebrahimi Zohravi, Lida; Vafafard, Azar; Mahmoudi, Mohammad, E-mail: mahmoudi@znu.ac.ir

    2014-07-01

    The optical properties of a weak probe field in a duplicated two-level system are investigated in multi-photon resonance (MPR) condition and beyond it. It is shown that by changing the relative phase of applied fields, the absorption switches to the amplification without inversion in MPR condition. By applying the Floquet decomposition to the equations of motion beyond MPR condition, it is shown that the phase-dependent behavior is valid only in MPR condition. Moreover, it is demonstrated that the group velocity of light pulse can be controlled by the intensity of the applied fields and the gain-assisted superluminal light propagation (fast light) is obtained in this system. In addition, the optical bistability (OB) behavior of the system is studied beyond MPR condition. We apply an indirect incoherent pumping field to the system and it is found that the group velocity and OB behavior of the system can be controlled by the incoherent pumping rate. - Highlights: • We studied the optical properties of DTL system under MPR condition and beyond it. • By changing the relative phase, the absorption switches to the amplification without inversion in MPR condition. • The gain-assisted superluminal light propagation (fast light) is obtained in this system. • The optical bistability (OB) behavior of the system is studied beyond MPR condition. • The incoherent pumping rate has a major role in controlling the group velocity and OB behavior of the system.

  10. Sizing PV-wind hybrid energy system for lighting

    Directory of Open Access Journals (Sweden)

    Mustafa Engin

    2012-09-01

    Full Text Available Sizing of wind and photovoltaic generators ensures lower operational costs and therefore, is considered as an important issue. An approach for sizing along with a best management technique for a PV-wind hybrid system with batteries is proposed in this paper, in which the best size for every component of the system could be optimized according to the weather conditions and the load profile. The average hourly values for wind speed and solar radiation for Izmir, Turkey has been used in the design of the systems, along with expected load profile. A hybrid power model is also developed for battery operation according to the power balance between generators and loads used in the software, to anticipate performances for the different systems according to the different weather conditions. The output of the program will display the performance of the system during the year, the total cost of the system, and the best size for the PV-generator, wind generator, and battery capacity. Using proposed procedure, a 1.2 kWp PV-wind hybrid system was designed for Izmir, and simulated and measured results are presented.

  11. An Advanced Light Weight Recuperator for Space Power Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Closed Brayton Cycle (CBC) space power system is one of the most efficient energy conversion technologies for nuclear and solar electric propulsion. The recuperator...

  12. 78 FR 64029 - Cost-Benefit Analysis for Radwaste Systems for Light-Water-Cooled Nuclear Power Reactors

    Science.gov (United States)

    2013-10-25

    ... COMMISSION Cost-Benefit Analysis for Radwaste Systems for Light-Water-Cooled Nuclear Power Reactors AGENCY... Systems for Light-Water-Cooled Nuclear Power Reactors,'' in which the NRC made editorial corrections and... analysis for liquid and gaseous radwaste system components for light water nuclear power...

  13. Generalized propagation of light through optical systems. II. Numerical implications.

    Science.gov (United States)

    Tessmer, Manuel; Gross, Herbert

    2015-12-01

    We present an algorithm implemented in a MATLAB toolbox that is able to compute the wave propagation of coherent visible light through macroscopic lenses. The mathematical operations that complete the status at the end of the first paper of this sequence, where only limited configurations of the propagation direction were allowed toward arbitrarily directed input beam computations, are provided. With their help, high numerical aperture (NA) field tracing is made possible that is based on fast Fourier routines and is Maxwell exact in the limit of macroscopic structures and large curvature radii, including reflection and transmission. Whereas the curvature-dependent terms in the Helmholtz equation are under analytical control through the first perturbation order in the curvature, they are only included in the propagation distance in the current investigation for the sake of reasonable time consumption. We give a number of examples that demonstrate the strengths of our approach, describe essential differences from other approaches that were not obvious when Paper 1 was written, and list a number of drawbacks and possible simplifications to overcome them.

  14. Office worker response to an automated venetian blind and electric lighting system: A pilot study

    Energy Technology Data Exchange (ETDEWEB)

    Vine, E.; Lee, E.; Clear, R.; DiBartolomeo, D.; Selkowitz, S.

    1998-03-01

    A prototype integrated, dynamic building envelope and lighting system designed to optimize daylight admission and solar heat gain rejection on a real-time basis in a commercial office building is evaluated. Office worker response to the system and occupant-based modifications to the control system are investigated to determine if the design and operation of the prototype system can be improved. Key findings from the study are: (1) the prototype integrated envelope and lighting system is ready for field testing, (2) most office workers (N=14) were satisfied with the system, and (3) there were few complaints. Additional studies are needed to explain how illuminance distribution, lighting quality, and room design can affect workplans illuminance preferences.

  15. Demonstration of a light-redirecting skylight system at the Palm Springs Chamber of Commerce

    Energy Technology Data Exchange (ETDEWEB)

    Lee, E.S.; Beltran, L.O.; Selkowitz, S.E. [Lawrence Berkeley National Lab., CA (United States); Lau, H.; Ander, G.D. [Southern California Edison, San Dimas, CA (United States)

    1996-05-01

    As part of a demonstration project to provide a comprehensive energy upgrade to a 294 m{sup 2} (3168 ft{sup 2}) commercial building, an advanced skylight design was developed using optical light control materials and geometry to provide daylight to two adjoining offices. The skylight system was developed using outdoor physical model tests and simulation tools Limited on-site measurements and occupant polls were conducted. Market issues were addressed. The skylight systems were found to improve lighting quality and to control excessive daylight illuminance levels compared to a conventional diffusing bubble skylight. Daylighting principles developed in earlier work for vertical glazing systems (light shelves and light pipes) were shown to be applicable in skylight designs at full-scale.

  16. Robust quantum correlations in out-of-equilibrium matter-light systems

    Science.gov (United States)

    Acevedo, O. L.; Quiroga, L.; Rodríguez, F. J.; Johnson, N. F.

    2015-09-01

    High precision macroscopic quantum control in interacting light-matter systems remains a significant goal toward novel information processing and ultra-precise metrology. We show that the out-of-equilibrium behavior of a paradigmatic light-matter system (Dicke model) reveals two successive stages of enhanced quantum correlations beyond the traditional schemes of near-adiabatic and sudden quenches. The first stage features magnification of matter-only and light-only entanglement and squeezing due to effective nonlinear self-interactions. The second stage results from a highly entangled light-matter state, with enhanced superradiance and signatures of chaotic and highly quantum states. We show that these new effects scale up consistently with matter system size, and are reliable even in dissipative environments.

  17. Recognition of Banknote Fitness Based on a Fuzzy System Using Visible Light Reflection and Near-infrared Light Transmission Images.

    Science.gov (United States)

    Kwon, Seung Yong; Pham, Tuyen Danh; Park, Kang Ryoung; Jeong, Dae Sik; Yoon, Sungsoo

    2016-06-11

    Fitness classification is a technique to assess the quality of banknotes in order to determine whether they are usable. Banknote classification techniques are useful in preventing problems that arise from the circulation of substandard banknotes (such as recognition failures, or bill jams in automated teller machines (ATMs) or bank counting machines). By and large, fitness classification continues to be carried out by humans, and this can cause the problem of varying fitness classifications for the same bill by different evaluators, and requires a lot of time. To address these problems, this study proposes a fuzzy system-based method that can reduce the processing time needed for fitness classification, and can determine the fitness of banknotes through an objective, systematic method rather than subjective judgment. Our algorithm was an implementation to actual banknote counting machine. Based on the results of tests on 3856 banknotes in United States currency (USD), 3956 in Korean currency (KRW), and 2300 banknotes in Indian currency (INR) using visible light reflection (VR) and near-infrared light transmission (NIRT) imaging, the proposed method was found to yield higher accuracy than prevalent banknote fitness classification methods. Moreover, it was confirmed that the proposed algorithm can operate in real time, not only in a normal PC environment, but also in an embedded system environment of a banknote counting machine.

  18. Recognition of Banknote Fitness Based on a Fuzzy System Using Visible Light Reflection and Near-infrared Light Transmission Images

    Directory of Open Access Journals (Sweden)

    Seung Yong Kwon

    2016-06-01

    Full Text Available Fitness classification is a technique to assess the quality of banknotes in order to determine whether they are usable. Banknote classification techniques are useful in preventing problems that arise from the circulation of substandard banknotes (such as recognition failures, or bill jams in automated teller machines (ATMs or bank counting machines. By and large, fitness classification continues to be carried out by humans, and this can cause the problem of varying fitness classifications for the same bill by different evaluators, and requires a lot of time. To address these problems, this study proposes a fuzzy system-based method that can reduce the processing time needed for fitness classification, and can determine the fitness of banknotes through an objective, systematic method rather than subjective judgment. Our algorithm was an implementation to actual banknote counting machine. Based on the results of tests on 3856 banknotes in United States currency (USD, 3956 in Korean currency (KRW, and 2300 banknotes in Indian currency (INR using visible light reflection (VR and near-infrared light transmission (NIRT imaging, the proposed method was found to yield higher accuracy than prevalent banknote fitness classification methods. Moreover, it was confirmed that the proposed algorithm can operate in real time, not only in a normal PC environment, but also in an embedded system environment of a banknote counting machine.

  19. Synchronization of Traffic Light Systems for Maximum Efficiency along Jalan Bukit Gambier, Penang, Malaysia

    Directory of Open Access Journals (Sweden)

    Ahmad Rafidi M.A.

    2014-01-01

    Full Text Available The synchronization of traffic light systems is one of the best solutions in order to avoid problematic traffic jams. Traffic timing is a major concern when it comes to traffic management. One of the common causes of traffic jams is because of nonsynchronized traffic light systems. Once a light turns green, traffic begins to move, but by the time the moving traffic reaches the next light, the signal is still red. This will disrupt the continuity of the traffic flow, especially for large main roads. The smooth flow of traffic on main routes is important to clear dense traffic in a given time. This study examined the density of vehicles on Jalan Bukit Gambier and also the traffic timing was documented in order to plan out proper re-timing for traffic lights along the studied road. The outcomes of this study support the hypothesis that retiming traffic lights to create a synchronized traffic light system for main roads will greatly improve traffic flow.

  20. Optimization of optical systems for LED spot lights concerning the color uniformity

    Science.gov (United States)

    Teupner, Anne; Bergenek, Krister; Wirth, Ralph; Miñano, Juan C.; Benítez, Pablo

    2014-09-01

    Spotlighting is one illumination field where the application of light emitting diodes (LED) creates many advantages. Commonly, the system for spot lights consists of a LED light engine and collimating secondary optics. Through angular or spatial separated emitted light from the source and imaging optical elements, a non uniform far field appears with colored rings, dots or patterns. Many feasible combinations result in very different spatial color distributions. Several combinations of three multi-chip light sources and secondary optical elements like reflectors and TIR lenses with additional facets or scattering elements were analyzed mainly regarding the color uniformity. They are assessed by the merit function Usl which was derived from human factor experiments and describes the color uniformity based on the visual perception of humans. Furthermore, the optical systems are compared concerning efficiency, peak candela and aspect ratio. Both types of optics differ in the relation between the color uniformity level and other properties. A plain reflector with a slightly color mixing light source performs adequate. The results for the TIR lenses indicate that they need additional elements for good color mixing or blended light source. The most convenient system depends on the requirements of the application.

  1. Application of a LED-based reflectance sensor for the assessing in situ the lycopene content of tomatoes (Lycopersicon esculentum Mill.)

    Science.gov (United States)

    Mignani, Anna G.; Ciaccheri, Leonardo; Mencaglia, Andrea A.; Tuccio, Lorenza; Agati, Giovanni

    2015-05-01

    Nondestructive in situ determination of the antioxidant lycopene of fresh tomato fruits is of large interest for the growers, willing to optimize the harvest time for high quality products. For this, we developed a portable LED-based colorimeter which was able to measure reflectance spectra of whole tomatoes in the 400-750 nm range. The tomato skins from the same samples were then frozen in liquid nitrogen, extracted with an acetone/ethanol/hexane mixture and analyzed by means of a spectrophotometer for their lycopene content. Concentration of lycopene was varying between 70 and 550 mg/Kg fresh weight skin. Partial Least Square regression was used to correlate spectral data to the tomato lycopene content. The multivariate processing of the reflectance data showed that lycopene content could be nicely predicted with a coefficient of determination R2=0.945 and a root mean square error of cross-validation RMSECV=57 mg/Kg skin fresh weight. These results suggest that portable, low-cost and compact LED-based sensors appear to be promising instruments for the nondestructive assessment of tomato lycopene even in the field.

  2. New Light Curves and Period Studies of V502 OPH W UMA System

    Science.gov (United States)

    Awadalla, Nabil S.

    NEW LIGHT CURVES AND PERIOD STUDIES OF V502 OPH W UMa SYSTEM N.S.Awadalla National Research Institute of Astronomy and Geophysics( NRIAG ) Helwan Cairo EGYPT New BVR photoelectric observations of the W UMa eclipsing binary system V502 Oph have been presented and analyzed. The geometric and physical elements of the system have been obtained and compared to the previous results. The classification of the system concerning the sub-type of the W UMa binary has been studied as well as its evolution stage. Its period variation in a view of the light time effect has been examin

  3. Engineering of a green-light inducible gene expression system in Synechocystis sp. PCC6803.

    Science.gov (United States)

    Abe, Koichi; Miyake, Kotone; Nakamura, Mayumi; Kojima, Katsuhiro; Ferri, Stefano; Ikebukuro, Kazunori; Sode, Koji

    2014-03-01

    In order to construct a green-light-regulated gene expression system for cyanobacteria, we characterized a green-light sensing system derived from Synechocystis sp. PCC6803, consisting of the green-light sensing histidine kinase CcaS, the cognate response regulator CcaR, and the promoter of cpcG2 (PcpcG 2 ). CcaS and CcaR act as a genetic controller and activate gene expression from PcpcG 2 with green-light illumination. The green-light induction level of the native PcpcG 2 was investigated using GFPuv as a reporter gene inserted in a broad-host-range vector. A clear induction of protein expression from native PcpcG 2 under green-light illumination was observed; however, the expression level was very low compared with Ptrc , which was reported to act as a constitutive promoter in cyanobacteria. Therefore, a Shine-Dalgarno-like sequence derived from the cpcB gene was inserted in the 5' untranslated region of the cpcG2 gene, and the expression level of CcaR was increased. Thus, constructed engineered green-light sensing system resulted in about 40-fold higher protein expression than with the wild-type promoter with a high ON/OFF ratio under green-light illumination. The engineered green-light gene expression system would be a useful genetic tool for controlling gene expression in the emergent cyanobacterial bioprocesses. © 2013 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

  4. Excitation migration in fluctuating light-harvesting antenna systems

    NARCIS (Netherlands)

    Chmeliov, J.; Trinkunas, G.; Amerongen, van H.; Valkunas, L.

    2016-01-01

    Complex multi-exponential fluorescence decay kinetics observed in various photosynthetic systems like photosystem II (PSII) have often been explained by the reversible quenching mechanism of the charge separation taking place in the reaction center (RC) of PSII. However, this description does not ac

  5. A Closed-Loop Smart Control System Driving RGB Light Emitting Diodes

    KAUST Repository

    Al-Saggaf, Abeer

    2015-05-01

    The demand for control systems that are highly capable of driving solid-state optoelectronic devices has significantly increased with the advancement of their efficiency and elevation of their current consumption. This work presents a closed-loop control system that is based on a microcontroller embedded system capable of driving high power optoelectronic devices. In this version of the system, the device in the center of control is a high-power red, green, and blue light emitting diode package. The system features a graphical user interface, namely an Android mobile phone application, in which the user can easily use to vary the light color and intensity of the light-emitting device wirelessly via Bluetooth. Included in the system is a feedback mechanism constituted by a red, green, and blue color sensor through which the user can use to observe feedback color information about the emitted light. The system has many commercial application including in-door lighting and research application including plant agriculture research fields.

  6. Practical homeostasis lighting control system using sensor agent robots for office space

    Science.gov (United States)

    Tokiwa, Momoko; Mita, Akira

    2014-03-01

    The comfortable space can be changed by season, age, physical condition and the like. However, the current systems are not able to resolve them absolutely. This research proposes the Homeostasis lighting control system based on the mechanism of biotic homeostasis for making the algorithms of apparatus control. Homeostasis are kept by the interaction of the three systems, endocrine system, immune system, and nervous system[1]. By the gradual reaction in the endocrine system, body's protective response in the immune system, and the electrical reaction in the nerve system, we can keep the environments against variable changes. The new lighting control system utilizes this mechanism. Firstly, we focused on legibility and comfort in the office space to construct the control model learning from the endocrine and immune systems. The mechanism of the endocrine system is used for ambient lights in the space is used considering circadian rhythm for comfort. For the legibility, the immune system is used to control considering devices near the human depending on the distance between the human. Simulations and the demonstration were conducted to show the feasibility. Finally, the nerve system was intruded to enhance the system.

  7. Methods for rapid evaluation of the stray light in optical systems

    Science.gov (United States)

    Perrin, Jean-Claude

    2004-02-01

    Quantitative analysis of stray light in optical system is often a burden for optical designers. Ghost images due to multiple reflections on the surfaces of lenses and mirrors must be minimized during the design and optimization phases. Stray light in general must be controlled also during the optomechanical drawings. Already presented at the ICSO 2000 conference (Ref. 1), the CODE V macro software PARASIT makes it possible to have a complete quantitative analysis of the ghost in a few minutes. The possibilities of PARASIT are summarized with emphasis given to recent developments and comparison are given with LightTools. To make a full evaluation of the stray light in general, the possibilities of Light Tools, MATLAB and EXCEL interacting together using the Microsoft Active X protocol are unbeatable, as long as methods and corresponding macros written in EXCEL VBA and MATLAB .m are at the disposal of the optical designer. A short overview of these possibilities are demonstrated in this paper.

  8. A comprehensive approach to integrated envelope and lighting systems for new commercial buildings

    Energy Technology Data Exchange (ETDEWEB)

    Lee, E.S.; Selkowitz, S.E.; Rubinstein, F.M.; Klems, J.H.; Beltran, L.O.; DiBartolomeo, D.L. [Lawrence Berkeley Lab., CA (United States). Building Technologies Program

    1994-05-01

    The authors define a comprehensive approach to integrated envelope and lighting systems design as one that balances energy efficiency with an equal regard to the resultant environmental quality. By integrating envelope components (glazing, shading, and daylighting), lighting components (fixtures and controls) and building HVAC/energy management control systems, they create building systems that have the potential to achieve significant decreases in electricity consumption and peak demand while satisfying occupant physiological and psychological concerns. This paper presents results on the development, implementation, and demonstration of two specific integrated envelope and lighting systems: (1) a system emphasizing dynamic envelope components and responsive electric lighting systems, that offer the potential to achieve energy efficiency goals and a near optimum comfort environment throughout the year by adapting to meteorological conditions and occupant preferences in real time, and (2) perimeter daylighting systems that increase the depth of daylight penetration from sidelight windows and improves visual comfort with the use of a small inlet aperture. The energy performance of the systems was estimated using the DOE-2 building energy simulation program. Field tests with reduced scale models were conducted to determine daylighting and thermal performance in real time under actual weather conditions. Demonstrations of these integrated systems are being planned or are in progress in collaboration with utility programs to resolve real-world implementation issues under complex site, building, and cost constraints. Results indicate that integrated systems offer solutions that not only achieve significant peak demand reductions but also realize consistent energy savings with added occupant comfort and satisfaction.

  9. Compact excimer laser light source for optical (mask) inspection systems

    Science.gov (United States)

    Pflanz, Tobias; Huber, Heinz

    2001-04-01

    The discharge pumped excimer laser is a gas laser providing ultra violet radiation with well defined spectral, temporal and spatial properties. The fast development of excimer lasers in recent years has succeeded in designing very compact, turn-key systems delivering up to 10 W of radiation at 248 nm (5 W at 193 nm and 1 W at 157 nm) with repetition rates up to 1000 Hz. Experimental data on important beam properties of excimer lasers in the field of mask inspection are being presented and discussed. Relevant parameters are spectral bandwidth, energetic pulse-to-pulse stability, pulse duration, beam pointing stability, beam direction stability, beam dimension, beam profile and coherence. We will compare the excimer laser with lamp sources and continuous wave lasers in the framework of these parameters. The discussion will show future opportunities of compact excimer lasers in optical inspection as well as in mask writing systems, improving resolution and throughput.

  10. Optical Systems for the Fourth Generation Light Source, 4GLS

    CERN Document Server

    Quinn, Frances; MacDonald, Mike; Roper, Mark

    2004-01-01

    4GLS is a multi-user, multi-source facility proposed for construction at Daresbury Laboratory in the UK. By exploiting super-conducting linac technology with energy recovery, it will combine three free electron lasers and a range of conventional synchrotron radiation sources covering the THz to SXR region. The facility will provide femtosecond pulses at high repetition rate, with the FELs delivering GW power in the VUV and XUV region. This paper discusses the options and challenges for the optical systems associated with the suite of photon sources. The beamlines will need to operate both independently and in flexible, synchronised combinations. Together with the requirements for preserving the ultra-bright, fast pulse properties, this places unique demands on the design, layout and operational modes. The paper summarises current technical achievements and identifies the research and development necessary before detailed design of the 4GLS optical systems.

  11. Light Fidelity (Li-Fi) Based Indoor Communication System

    OpenAIRE

    Farooq Aftab; Muhammad Nafees Ulfat khan; Shahzad Ali

    2016-01-01

    Indoor wireless communication is an essential part of next generation wireless communication system.For an indoor communication number of users and their device are increasing very rapidly so as a result capacity of frequency spectrum to accommodate further users in future is limited and also it would be difficult for service providers to provide more user reliable and high speed communication so this short come can be solve in future by using Li-Fi based indoor communication syst...

  12. Phosphor Systems for Illumination Quality Solid State Lighting Products

    Energy Technology Data Exchange (ETDEWEB)

    Setlur, Anant; Briel, Linda; Cleaver, Robert; Clothier, Brent; Gao, Yan; Harlow, Richard; Henderson, Claire; Heward, William; Hill, M Christine; Lyons, Robert; Murphy, James; Siclovan, Oltea; Stoklosa, Stan; Happek, Uwe; Aanegola, Srinath; Aesram, Danny; Deshpande, Anirudha; Jacob, Cherian; Kolodin, Boris; Stoklosa, Emil; Beers, Williams

    2010-03-31

    The objective of this program is to develop phosphor systems that will enable LED lamps with 96 lm/W efficacy at correlated color temperatures, (CCTs) ~3000 K, and color rendering indices (CRIs) >80 and 71 lm/W efficacy at CCT<3100 K and CRI~95 using phosphor downconversion of LEDs. This primarily involves the invention and development of new phosphor materials that have improved efficiency and better match the eye sensitivity curves.

  13. Modeling and Prototyping of Automatic Clutch System for Light Vehicles

    Science.gov (United States)

    Murali, S.; Jothi Prakash, V. M.; Vishal, S.

    2017-03-01

    Nowadays, recycling or regenerating the waste in to something useful is appreciated all around the globe. It reduces greenhouse gas emissions that contribute to global climate change. This study deals with provision of the automatic clutch mechanism in vehicles to facilitate the smooth changing of gears. This study proposed to use the exhaust gases which are normally expelled out as a waste from the turbocharger to actuate the clutch mechanism in vehicles to facilitate the smooth changing of gears. At present, clutches are operated automatically by using an air compressor in the four wheelers. In this study, a conceptual design is proposed in which the clutch is operated by the exhaust gas from the turbocharger and this will remove the usage of air compressor in the existing system. With this system, usage of air compressor is eliminated and the riders need not to operate the clutch manually. This work involved in development, analysation and validation of the conceptual design through simulation software. Then the developed conceptual design of an automatic pneumatic clutch system is tested with proto type.

  14. Development of gamma-photon/Cerenkov-light hybrid system for simultaneous imaging of I-131 radionuclide

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Seiichi; Suzuki, Mayumi; Kato, Katsuhiko [Radiological and Medical Laboratory Sciences, Nagoya University Graduate School of Medicine (Japan); Watabe, Tadashi; Ikeda, Hayato; Kanai, Yasukazu [Department of Molecular Imaging in Medicine, Osaka University Graduate School of Medicine (Japan); Ogata, Yoshimune [Radiological and Medical Laboratory Sciences, Nagoya University Graduate School of Medicine (Japan); Hatazawa, Jun [Department of Molecular Imaging in Medicine, Osaka University Graduate School of Medicine (Japan)

    2016-09-11

    Although iodine 131 (I-131) is used for radionuclide therapy, high resolution images are difficult to obtain with conventional gamma cameras because of the high energy of I-131 gamma photons (364 keV). Cerenkov-light imaging is a possible method for beta emitting radionuclides, and I-131 (606 MeV maximum beta energy) is a candidate to obtain high resolution images. We developed a high energy gamma camera system for I-131 radionuclide and combined it with a Cerenkov-light imaging system to form a gamma-photon/Cerenkov-light hybrid imaging system to compare the simultaneously measured images of these two modalities. The high energy gamma imaging detector used 0.85-mm×0.85-mm×10-mm thick GAGG scintillator pixels arranged in a 44×44 matrix with a 0.1-mm thick reflector and optical coupled to a Hamamatsu 2 in. square position sensitive photomultiplier tube (PSPMT: H12700 MOD). The gamma imaging detector was encased in a 2 cm thick tungsten shield, and a pinhole collimator was mounted on its top to form a gamma camera system. The Cerenkov-light imaging system was made of a high sensitivity cooled CCD camera. The Cerenkov-light imaging system was combined with the gamma camera using optical mirrors to image the same area of the subject. With this configuration, we simultaneously imaged the gamma photons and the Cerenkov-light from I-131 in the subjects. The spatial resolution and sensitivity of the gamma camera system for I-131 were respectively ~3 mm FWHM and ~10 cps/MBq for the high sensitivity collimator at 10 cm from the collimator surface. The spatial resolution of the Cerenkov-light imaging system was 0.64 mm FWHM at 10 cm from the system surface. Thyroid phantom and rat images were successfully obtained with the developed gamma-photon/Cerenkov-light hybrid imaging system, allowing direct comparison of these two modalities. Our developed gamma-photon/Cerenkov-light hybrid imaging system will be useful to evaluate the advantages and disadvantages of these two

  15. Development of gamma-photon/Cerenkov-light hybrid system for simultaneous imaging of I-131 radionuclide

    Science.gov (United States)

    Yamamoto, Seiichi; Suzuki, Mayumi; Kato, Katsuhiko; Watabe, Tadashi; Ikeda, Hayato; Kanai, Yasukazu; Ogata, Yoshimune; Hatazawa, Jun

    2016-09-01

    Although iodine 131 (I-131) is used for radionuclide therapy, high resolution images are difficult to obtain with conventional gamma cameras because of the high energy of I-131 gamma photons (364 keV). Cerenkov-light imaging is a possible method for beta emitting radionuclides, and I-131 (606 MeV maximum beta energy) is a candidate to obtain high resolution images. We developed a high energy gamma camera system for I-131 radionuclide and combined it with a Cerenkov-light imaging system to form a gamma-photon/Cerenkov-light hybrid imaging system to compare the simultaneously measured images of these two modalities. The high energy gamma imaging detector used 0.85-mm×0.85-mm×10-mm thick GAGG scintillator pixels arranged in a 44×44 matrix with a 0.1-mm thick reflector and optical coupled to a Hamamatsu 2 in. square position sensitive photomultiplier tube (PSPMT: H12700 MOD). The gamma imaging detector was encased in a 2 cm thick tungsten shield, and a pinhole collimator was mounted on its top to form a gamma camera system. The Cerenkov-light imaging system was made of a high sensitivity cooled CCD camera. The Cerenkov-light imaging system was combined with the gamma camera using optical mirrors to image the same area of the subject. With this configuration, we simultaneously imaged the gamma photons and the Cerenkov-light from I-131 in the subjects. The spatial resolution and sensitivity of the gamma camera system for I-131 were respectively ~3 mm FWHM and ~10 cps/MBq for the high sensitivity collimator at 10 cm from the collimator surface. The spatial resolution of the Cerenkov-light imaging system was 0.64 mm FWHM at 10 cm from the system surface. Thyroid phantom and rat images were successfully obtained with the developed gamma-photon/Cerenkov-light hybrid imaging system, allowing direct comparison of these two modalities. Our developed gamma-photon/Cerenkov-light hybrid imaging system will be useful to evaluate the advantages and disadvantages of these two

  16. LED surgical lighting system with multiple free-form surfaces for highly sterile operating theater application.

    Science.gov (United States)

    Liu, Peng; Zhang, Yaqin; Zheng, Zhenrong; Li, Haifeng; Liu, Xu

    2014-06-01

    Although the ventilation system is widely employed in the operating theater, a strictly sterile surgical environment still cannot be ensured because of laminar disturbance, which is mainly caused by the surgical lighting system. Abandoning traditional products, we propose an LED surgical lighting system, which can alleviate the laminar disturbance and provide an appropriate lighting condition for surgery. It contains a certain amount of LED lens units, which are embedded in the ceiling and arranged around the air supply smallpox. The LED lens unit integrated with an LED light source and a free-form lens is required to produce a uniform circular illumination with a large tolerance to the change of lighting distance. To achieve such a dedicated lens, two free-form refractive surfaces, which are converted into two ordinary differential equations by the design method presented in this paper, are used to deflect the rays. The results show that the LED surgical lighting system can provide an excellent illumination environment for surgery, and, apparently, the laminar disturbance also can be relieved.

  17. 3D Wide FOV Scanning Measurement System Based on Multiline Structured-Light Sensors

    Directory of Open Access Journals (Sweden)

    He Gao

    2014-03-01

    Full Text Available Structured-light three-dimensional (3D vision measurement is currently one of the most common approaches to obtain 3D surface data. However, the existing structured-light scanning measurement systems are primarily constructed on the basis of single sensor, which inevitably generates three obvious problems: limited measurement range, blind measurement area, and low scanning efficiency. To solve these problems, we developed a novel 3D wide FOV scanning measurement system which adopted two multiline structured-light sensors. Each sensor is composed of a digital CCD camera and three line-structured-light projectors. During the measurement process, the measured object is scanned by the two sensors from two different angles at a certain speed. Consequently, the measurement range is expanded and the blind measurement area is reduced. More importantly, since six light stripes are simultaneously projected on the object surface, the scanning efficiency is greatly improved. The Multiline Structured-light Sensors Scanning Measurement System (MSSS is calibrated on site by a 2D pattern. The experimental results show that the RMS errors of the system for calibration and measurement are less than 0.092 mm and 0.168 mm, respectively, which proves that the MSSS is applicable for obtaining 3D object surface with high efficiency and accuracy.

  18. The Key Providing System for Wireless Lan Using Visible Light Communication

    Directory of Open Access Journals (Sweden)

    Kuniyoshi Okuda

    2014-06-01

    Full Text Available Public wireless LAN services have been increasing recently. These are convenient services for carrier companies particularly. And carrier companies and the user can disperse traffic. However in order to improve the convenience, the services do not often use the encryption key or do not change the encryption key that has already been set. Therefore, the services have a problem in safety. This paper solves this problem using the visible light communication. The visible light communication sends a signal by blinking the light. One of the visible light communication features is that we can see the transmission area. The visible light communication can use lighting equipments as the transmitter unlike infrared or conventional radio communications. Further, visible light communication can separate to clarify the transmission range by using light. We propose the distribution of the encryption key and the SSID using visible light communication. Visible light communication can easily prepare a small network, such as a partition or per a room basis. For malicious users connecting to the network is necessary to enter in the service provided area. Thus the administrator is able to easily manage legitimate users. In addition, it is possible to update the SSID and the encryption key by visible light communication easily for an administrator. Thus if malicious users get the SSID and the encryption key, they cannot use the SSID and the encryption key immediately. Normal users may only need to run the shell script for receiving information from the receiver. Therefore, convenience is good. In order to confirm the improved convenience, we measured the time it takes for a user to connect to the network. Conventional methods are methods that use or do not use the encryption key. As a result, users can connect to the network in a short time compared with the conventional methods. The system becomes stronger than conventional methods because it is possible to update

  19. 1.6 Gbit/s phosphorescent white LED based VLC transmission using a cascaded pre-equalization circuit and a differential outputs PIN receiver.

    Science.gov (United States)

    Huang, Xingxing; Wang, Zhixin; Shi, Jianyang; Wang, Yiguang; Chi, Nan

    2015-08-24

    We proposed a cascaded amplitude equalizer used for high speed visible light communications (VLC) system. With the cascaded pre-equalization circuit, the -3dB bandwidth of VLC system can be extended from 17MHz to 366MHz using a commercially available phosphorescent white LED, a blue filter and a differential outputs PIN receiver. The data rate is 1.60Gbit/s exploiting 16QAM-OFDM with 400MHz modulation bandwidth over 1m free-space transmission under pre-forward error correction (pre-FEC) limit of 3.8 × 10(-3). To our knowledge, this is the highest data rate ever achieved by using a commercially available phosphorescent white LED in VLC system.

  20. Quantum mechanical treatment of traveling light in an absorptive medium of two-level systems

    Science.gov (United States)

    Inoue, K.

    2016-12-01

    Quantum mechanical treatment of a light wave that propagates through an absorptive medium is presented. Unlike a phenomenological beam-splitter model conventionally employed to describe a traveling light in a lossy medium, the time evolution of the field operator is derived using the Heisenberg equation with the Hamiltonian for a physical system, where the light wave interacts with an ensemble of two-level systems in a medium. Using the obtained time-evolved field operators, the mean values and variances of the light amplitude and the photon number are evaluated. The results are in agreement with those obtained in the beam-splitter model, giving a logical theoretical basis for the phenomenological beam-splitter model.

  1. Novel method for correcting light intensity fluctuation in the TDLAS system

    Institute of Scientific and Technical Information of China (English)

    Guojie Tu; Yu Wang; Fengzhong Dong; Hua Xia; Tao Pang; Zhirong Zhang; Bian Wu

    2012-01-01

    A novel method for online correction of light intensity fluctuation in a practical tunable diode laser absorption spectroscopy (TDLAS) system with wavelength modulation is presented.The proposed method is developed according to the linear relation between peaks at multiple frequencies of sine modulation in the power spectral density of the demodulated second-harmonic (2f) signal and the incident light intensity.Those peaks are demonstrated experimentally and explained as residual power at the first-harmonic and third-harmonic frequencies after 2f demodulation of the residual amplitude modulation signal due to the limited integrating time constant of the lock-in-amplifier.This method can achieve real-time correction of light intensity fluctuations with only little calculation.It can work well in a very large range of light intensity and has great potential applications in the wavelength modulation spectroscopy system.

  2. Posture parameters optimization of a structured light 3D angle measuring system

    Directory of Open Access Journals (Sweden)

    Xun DING

    2015-10-01

    Full Text Available To improve the measurement precision of the structured light target angle, this paper studies the relation between the structured light system parameters and measurement accuracy of the angle. Firstly, the main system structure parameters influencing the angle measurement precision are analyzed based on the structured light measurement principle; secondly, simulation research on the laws of how the structured parameters influence the angle measurement precision are conducted, and the optimized range of values of the structured parameters is proposed; finally, the experimental studies show that, the optimized parameters can improve the angle measurement precision effectively, which lays the design foundation for later improvement schemes of the structured light 3D four-wheel alignment instrument.

  3. Determining optimal pattern sequences for three-dimensional structured light sensory systems.

    Science.gov (United States)

    Marin, Veronica E; Nejat, Goldie

    2016-04-20

    Structured light (SL) techniques are used for three-dimensional (3D) measurements of objects in a wide variety of applications. SL-based sensory systems obtain the 3D surface profile of an object from the deformation of light patterns projected onto the object of interest. The number of fringes used in the projected light patterns has a direct effect on the 3D reconstruction errors. This paper presents a novel methodology for determining the optimal sequence of multi-fringe patterns that minimizes reconstruction errors caused by random noise. Experiments conducted with a variety of objects as well as a comparison study demonstrate the effectiveness of the proposed methodology.

  4. A white–cyan-red LED system for low correlated colour temperature lighting

    DEFF Research Database (Denmark)

    Chakrabarti, Maumita; Thorseth, Anders; Corell, Dennis Dan

    2015-01-01

    on chromaticity and colour rendering indices. A geometric optical model is used to design and optimize the homogeneity of the colour and light intensity distribution as a function of angle. The resulting system produces diffused homogeneous white light with a tunable correlated colour temperature from 2000 K...... to 2400 K. Within this range the white light is characterized by a high general colour rendering index (Ra>90), special colour rendering indices for saturated red objects (R9>85), and low chromaticity distance (Duv) from the Planckian locus (Duv

  5. Critical Behavior in Light Nuclear Systems: (I) Experimental Aspects

    CERN Document Server

    Ma, Y G; Wada, R; Hagel, K; Wang, J; Keutgen, T; Majka, Z; Murray, M; Qin, L; Smith, P; Alfaro, R; Cibor, J; Cinausero, M; Masri, Y E; Fabris, D; Fioretto, E; Keksis, A L; Lunardon, M; Makeev, A; Marie, N; Martin, E; Martínez-Davalos, A; Menchaca-Rocha, A; Nebbia, G; Prete, G; Rizzi, V; Ruangma, A; Shetty, D V; Souliotis, G A; Staszel, P; Veselsky, M; Viesti, G; Winchester, E M; Yennello, S J

    2004-01-01

    An extensive experimental survey of the features of the disassembly of a small quasi-projectile system with $A \\sim$ 36, produced in the reactions of 47 MeV/nucleon $^{40}$Ar + $^{27}$Al, $^{48}$Ti and $^{58}$Ni, has been carried out. Nuclei in the excitation energy range of 1-9 MeV/u have been investigated employing a new method to reconstruct the quasi-projectile source. At an excitation energy $\\sim$ 5.6 MeV/nucleon many observables indicate the presence of maximal fluctuations in the de-excitation processes. The fragment topological structure shows that the rank sorted fragments obey Zipf's law at the point of largest fluctuations providing another indication of a liquid gas phase transition. The caloric curve for this system shows a monotonic increase of temperature with excitation energy and no apparent plateau. The temperature at the point of maximal fluctuations is $8.3 \\pm 0.5$ MeV. Taking this temperature as the critical temperature and employing the caloric curve information we have extracted the c...

  6. Optimal RF Systems for Lightly Loaded Superconducting Structures

    CERN Document Server

    Zwart, Townsend; Graves, William S; Wang, D; Zolfaghari, Abbi

    2004-01-01

    Recent developments in the field of RF accelerators have created a demand for power amplifiers that can support very high accelerating gradients, 15-25 MV/m, in superconducting structures with extremely low losses. Free electron lasers (FEL’s) with modest beam current, I< 10 uA, or based on energy recovery linacs (ERL’s) may have intrinsic power demands of less than 1 kW/m. We present the design of an amplifier and external tuner system that will efficiently meet this requirement. The RF amplifier, an Inductive Output Tube (IOT), offers high AC/RF efficiency, flexible power output and switching capability without the need for external modulation. The tuner circuit makes use of low loss ferrite phase shifters to create a moderate quality standing wave (Q~100-1000) between the amplifier and the superconducting cavity. An alternative design based on a shorter cavity structure and employing solid state amplifiers is also presented. The expected performance characteristics of both systems are described.

  7. Post-post-Newtonian deflection of light ray in multiple systems with PPN parameters

    Institute of Scientific and Technical Information of China (English)

    Gong Yan-Xiang; Wu Xiao-Mei

    2011-01-01

    The post-Newtonian scheme in multiple systems with post-Newtonian parameters presented by Klioner and Soffel is extended to the post-post-Newtonian (PPN) order for light propagation problem in the solar system. Under considering the solar system experiment requirement, a new parameter e is introduced. This extension does not change the virtue of the scheme on the linear partial differential equations of the potential and vector potential mentioned in previous work. Furthermore, this extension is based on the former work done by Richter and Matzner in one global system theory. As an application, we also consider the deflection of light ray in the global coordinates. And the deflection angle of light ray is obtained with post-Newtonian parameters.

  8. Pipeline inwall 3D measurement system based on the cross structured light

    Science.gov (United States)

    Shen, Da; Lin, Zhipeng; Xue, Lei; Zheng, Qiang; Wang, Zichi

    2014-01-01

    In order to accurately realize the defect detection of pipeline inwall, this paper proposes a measurement system made up of cross structured light, single CCD camera and a smart car, etc. Based on structured light measurement technology, this paper mainly introduces the structured light measurement system, the imaging mathematical model, and the parameters and method of camera calibration. Using these measuring principles and methods, the camera in remote control car platform achieves continuous shooting of objects and real-time rebound processing as well as utilizing established model to extract 3D point cloud coordinate to reconstruct pipeline defects, so it is possible to achieve 3D automatic measuring, and verifies the correctness and feasibility of this system. It has been found that this system has great measurement accuracy in practice.

  9. Designing display primaries with currently available light sources for UHDTV wide-gamut system colorimetry.

    Science.gov (United States)

    Masaoka, Kenichiro; Nishida, Yukihiro; Sugawara, Masayuki

    2014-08-11

    The wide-gamut system colorimetry has been standardized for ultra-high definition television (UHDTV). The chromaticities of the primaries are designed to lie on the spectral locus to cover major standard system colorimetries and real object colors. Although monochromatic light sources are required for a display to perfectly fulfill the system colorimetry, highly saturated emission colors using recent quantum dot technology may effectively achieve the wide gamut. This paper presents simulation results on the chromaticities of highly saturated non-monochromatic light sources and gamut coverage of real object colors to be considered in designing wide-gamut displays with color filters for the UHDTV.

  10. Analysis of Topological Impact on Wireless Channel Performance on Intelligent Street Lighting System

    Directory of Open Access Journals (Sweden)

    L. Azpilicueta

    2014-04-01

    Full Text Available In this work, an analysis of the physical radio channel propagation for the deployment of a wireless sensor network for intelligent street lighting is presented based on an in house implemented 3D ray launching code. Simulation as well as measurement results from a deployed wireless sensor network for an intelligent street light control system confirm the topological and morphological dependence of the considered scenario. The results can be applied to the optimal radioplanning of the wireless systems prior to deployment phase, in order to achieve maximum system performance while minimizing power consumption.

  11. A service platform architecture design towards a light integration of heterogeneous systems in the wellbeing domain.

    Science.gov (United States)

    Yang, Yaojin; Ahtinen, Aino; Lahteenmaki, Jaakko; Nyman, Petri; Paajanen, Henrik; Peltoniemi, Teijo; Quiroz, Carlos

    2007-01-01

    System integration is one of the major challenges for building wellbeing or healthcare related information systems. In this paper, we are going to share our experiences on how to design a service platform called Nuadu service platform, for providing integrated services in occupational health promotion and health risk management through two heterogeneous systems. Our design aims for a light integration covering the layers, from data through service up to presentation, while maintaining the integrity of the underlying systems.

  12. Spectral light management for solar energy conversion systems

    Directory of Open Access Journals (Sweden)

    Stanley Cameron

    2016-06-01

    Full Text Available Due to the inherent broadband nature of the solar radiation, combined with the narrow spectral sensitivity range of direct solar to electricity devices, there is a massive opportunity to manipulate the solar spectrum to increase the functionality and efficiency of solar energy conversion devices. Spectral splitting or manipulation facilitates the efficient combination of both high-temperature solar thermal systems, which can absorb over the entire solar spectrum to create heat, and photovoltaic cells, which only convert a range of wavelengths to electricity. It has only recently been possible, with the development of nanofabrication techniques, to integrate micro- and nano-photonic structures as spectrum splitters/manipulators into solar energy conversion devices. In this paper, we summarize the recent developments in beam splitting techniques, and highlight some relevant applications including combined PV-thermal collectors and efficient algae production, and suggest paths for future development in this field.

  13. Hidden symmetries enhance quantum transport in Light Harvesting systems

    CERN Document Server

    Zech, Tobias; Wellens, Thomas; Buchleitner, Andreas

    2012-01-01

    For more than 50 years we have known that photosynthetic systems harvest solar energy with almost unit {\\it quantum efficiency}. However, recent experimental evidence of {\\it quantum coherence} during the excitonic energy transport in photosynthetic organisms challenges our understanding of this fundamental biological function. Currently, and despite numerous efforts, the causal connection between coherence and efficiency is still a matter of debate. We show, through the study of extensive simulations of quantum coherent transport on networks, that three dimensional structures characterized by centro-symmetric Hamiltonians are statistically more efficient than random arrangements. Moreover, we demonstrate that the experimental data available for the electronic Hamiltonians of the Fenna-Mathew-Olson (FMO) complex of sulfur bacteria and of the crypophyte PC645 complex of marine algae are consistent with this strong correlation of centro-symmetry with quantum efficiency. These results show that what appears to b...

  14. Spectral light management for solar energy conversion systems

    Science.gov (United States)

    Stanley, Cameron; Mojiri, Ahmad; Rosengarten, Gary

    2016-06-01

    Due to the inherent broadband nature of the solar radiation, combined with the narrow spectral sensitivity range of direct solar to electricity devices, there is a massive opportunity to manipulate the solar spectrum to increase the functionality and efficiency of solar energy conversion devices. Spectral splitting or manipulation facilitates the efficient combination of both high-temperature solar thermal systems, which can absorb over the entire solar spectrum to create heat, and photovoltaic cells, which only convert a range of wavelengths to electricity. It has only recently been possible, with the development of nanofabrication techniques, to integrate micro- and nano-photonic structures as spectrum splitters/manipulators into solar energy conversion devices. In this paper, we summarize the recent developments in beam splitting techniques, and highlight some relevant applications including combined PV-thermal collectors and efficient algae production, and suggest paths for future development in this field.

  15. Development of a Calibration System for Cryogenic Light Detectors in CUPID

    Science.gov (United States)

    Luo, Meng; Kolomensky, Yury; O'Donnell, Thomas; Schmidt, Benjamin; Cupid Collaboration

    2017-01-01

    If neutrino is a Majorana particle, it is possible to observe neutrinoless double beta decay (0 νββ), whose signature is a monochromatic line at the Q-value of the decay in the energy spectrum of the two electrons. Cryogenic Underground Observatory for Rare Events (CUORE) is an experiment which aims to search for 0 νββ in 130Te with TeO2 bolometers, whose background is dominated by α particles from natural radioactivity in the detector material. CUPID (CUORE Upgrade with Particle IDentification) is the next generation experiment proposed to distinguish 0 νββ events from those of α particles with Cherenkov radiation. An important part of CUPID R&D is to design, build and characterize a calibration system that can generate a known amount of light and transport that light to the dilution refrigerator at mK temperatures. We describe the design, implementation and performance of a calibration system developed for bolometric light detectors. Preparation work includes researching and selecting a light source (LED). A transport system (optical fiber) was developed to direct the light to the coldest part of the dilution refrigerator. Additionally, the light yield attenuation of optical fiber at cryogenic temperatures was measured. This project is supported by National Science Foundation and UC-Berkeley.

  16. Revisiting Bourdieu: Alternative Educational Systems in the Light of the Theory of Social and Cultural Reproduction

    Science.gov (United States)

    Azaola, Marta Cristina

    2012-01-01

    The paper reflects upon the principles and practice of an alternative educational system operating in rural Mexico in the light of Bourdieu's theory of cultural and social reproduction. Bourdieu's theory seeks to explain processes of reproduction of power relations within schools and society; whereas alternative educational systems seek to expand…

  17. The Light-Pulser Monitoring System for the WASA detector facility

    Science.gov (United States)

    Zabierowski, J.; Rachowski, J.

    2009-07-01

    The design and performance of the system for monitoring the stability of the scintillation counters in the WASA multi-detector apparatus are presented. The system utilizes light pulses generated by LEDs and a Xenon flash tube, for monitoring plastic and inorganic scintillator based counters, respectively.

  18. Revisiting Bourdieu: Alternative Educational Systems in the Light of the Theory of Social and Cultural Reproduction

    Science.gov (United States)

    Azaola, Marta Cristina

    2012-01-01

    The paper reflects upon the principles and practice of an alternative educational system operating in rural Mexico in the light of Bourdieu's theory of cultural and social reproduction. Bourdieu's theory seeks to explain processes of reproduction of power relations within schools and society; whereas alternative educational systems seek to expand…

  19. Preliminary greenhouse design for a Martian colony: Structural, solar collection, and light distribution systems

    Science.gov (United States)

    1990-11-01

    The design of a greenhouse that will be a component of a long-term habitat on Mars is presented. The greenhouse will be the primary food source for people stationed on Mars. The food will be grown in three identical underground modules, pressurized at 1 atm to allow a shirt-sleeve environment within the greenhouse. The underground location will support the structure, moderate the large environmental variations on the surface, and protect the crops from cosmic radiation. The design effort is concentrated on the outer structure and the lighting system for the greenhouse. The structure is inflatable and made of a Kevlar 49/Epoxy composite and a pipe-arched system that is corrugated to increase stiffness. This composite is pliable in an uncured state, which allows it to be efficiently packaged for transport. The lighting system consists of several flat-plate fiber optic solar collectors with dual-axis tracking systems that will continually track the sun. This design is modeled after the Himawari collector, which was designed by Dr. Kei Mori and is currently in use in Japan. The light will pass through Fresnel lenses that filter out undesirable wavelengths and send the light into the greenhouses by way of fiber optic cables. When the light arrives at the greenhouse, it is dispersed to the plants via a waveguide and diffuser system.

  20. Monolithic white LED based on AlxGa1-x N/InyGa1-yN DBR resonant-cavity

    Science.gov (United States)

    Yu, Chen; Lirong, Huang; Shanshan, Zhu

    2009-01-01

    A monolithic white light-emitting diode (LED) with blue and yellow light active regions has been designed and studied. With the AlxGa1-xN/InyGa1-yN distributed Bragg reflector (DBR) resonant-cavity, the extraction efficiency and power of the yellow light are enhanced so that high quality white light can be obtained.

  1. Influence of irradiation by {sup 60}Co gamma-quanta on reliability of IR-LEDs based upon AlGaAs heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Gradoboev, Alexander V.; Simonova, Anastasiia V.; Orlova, Ksenia N. [National Research Tomsk Polytechnic University, Lenina avenue 30, 634050 Tomsk (Russian Federation)

    2016-12-15

    We consider the influence of preliminary irradiation by {sup 60}Co gamma quanta on emission power decrease during the operating time of IR-LEDs based upon AlGaAs double heterostructures. Irradiation was realized in passive power mode of the LEDs prior to aging. Aging under long operating time conditions was simulated by a step-stress approach. We have determined that the emissive power decrease of LED during operating time has two stages. On the first stage, decrease of LED emissive power is due to rearrangement of original defect structure. On the second stage, emissive power goes down as the result of inducing new structural defects. We have shown identical multistage mechanisms of emissive power drop are observed during both operating time and influence of ionizing radiation. We have established that preliminary irradiation has increased reliability and operating time of LEDs. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  2. Lighting: Green Light.

    Science.gov (United States)

    Maniccia, Dorine

    2003-01-01

    Explains that by using sustainable (green) building practices, schools and universities can make their lighting systems more efficient, noting that embracing green design principles can help schools attract students. Discusses lighting-control technologies (occupancy sensing technology, daylighting technology, and scheduling based technologies),…

  3. Modelling and Simulation of SVPWM Based Vector Controlled HVDC Light Systems

    Directory of Open Access Journals (Sweden)

    Ajay Kumar MOODADLA

    2012-11-01

    Full Text Available Recent upgrades in power electronics technology have lead to the improvements of insulated gate bipolar transistor (IGBT based Voltage source converter High voltage direct current (VSC HVDC transmission systems. These are also commercially known as HVDC Light systems, which are popular in renewable, micro grid, and electric power systems. Out of different pulse width modulation (PWM schemes, Space vector PWM (SVPWM control scheme finds growing importance in power system applications because of its better dc bus utilization. In this paper, modelling of the converter is described, and SVPWM scheme is utilized to control the HVDC Light system in order to achieve better DC bus utilization, harmonic reduction, and for reduced power fluctuations. The simulations are carried out in the MATLAB/SIMULINK environment and the results are provided for steady state and dynamic conditions. Finally, the performance of SVPWM based vector controlled HVDC Light transmission system is compared with sinusoidal pulse width modulation (SPWM based HVDC Light system in terms of output voltage and total harmonic distortion (THD.

  4. An Artificial Neural Network for Analyzing Overall Uniformity in Outdoor Lighting Systems

    Directory of Open Access Journals (Sweden)

    Antonio del Corte-Valiente

    2017-02-01

    Full Text Available Street lighting installations are an essential service for modern life due to their capability of creating a welcoming feeling at nighttime. Nevertheless, several studies have highlighted that it is possible to improve the quality of the light significantly improving the uniformity of the illuminance. The main difficulty arises when trying to improve some of the installation’s characteristics based only on statistical analysis of the light distribution. This paper presents a new algorithm that is able to obtain the overall illuminance uniformity in order to improve this sort of installations. To develop this algorithm it was necessary to perform a detailed study of all the elements which are part of street lighting installations. Because classification is one of the most important tasks in the application areas of artificial neural networks, we compared the performances of six types of training algorithms in a feed forward neural network for analyzing the overall uniformity in outdoor lighting systems. We found that the best algorithm that minimizes the error is “Levenberg-Marquardt back-propagation”, which approximates the desired output of the training pattern. By means of this kind of algorithm, it is possible to help to lighting professionals optimize the quality of street lighting installations.

  5. High-resolution light field reconstruction using a hybrid imaging system.

    Science.gov (United States)

    Wang, Xiang; Li, Lin; Hou, GuangQi

    2016-04-01

    Recently, light field cameras have drawn much attraction for their innovative performance in photographic and scientific applications. However, narrow baselines and constrained spatial resolution of current light field cameras impose restrictions on their usability. Therefore, we design a hybrid imaging system containing a light field camera and a high-resolution digital single lens reflex camera, and these two kinds of cameras share the same optical path with a beam splitter so as to achieve the reconstruction of high-resolution light fields. The high-resolution 4D light fields are reconstructed with a phase-based perspective variation strategy. First, we apply complex steerable pyramid decomposition on the high-resolution image from the digital single lens reflex camera. Then, we perform phase-based perspective-shift processing with the disparity value, which is extracted from the upsampled light field depth map, to create high-resolution synthetic light field images. High-resolution digital refocused images and high-resolution depth maps can be generated in this way. Furthermore, controlling the magnitude of the perspective shift enables us to change the depth of field rendering in the digital refocused images. We show several experimental results to demonstrate the effectiveness of our approach.

  6. A novel mirror diversity receiver for indoor MIMO visible light communication systems

    KAUST Repository

    Park, Kihong

    2016-12-24

    In this paper, we propose and study a non-imaging receiver design reducing the correlation of channel matrix for indoor multiple-input multiple-output (MIMO) visible light communication (VLC) systems. Contrary to previous works, our proposed mirror diversity receiver (MDR) not only blocks the reception of light on one specific direction but also improves the channel gain on the other direction by receiving the light reflected by a mirror deployed between the photodetectors. We analyze the channel capacity and optimal height of mirror in terms of maximum channel capacity for a 2 × 2 MIMO-VLC system in a 2-dimensional geometric model. We prove that this constructive and destructive effects in channel matrix resulting from our proposed MDR are more beneficial to obtain well-conditioned channel matrix which is suitable for implementing spatial-multiplexing MIMO-VLC systems in order to support high data rate.

  7. Novel calibration method for structured-light system with an out-of-focus projector.

    Science.gov (United States)

    Li, Beiwen; Karpinsky, Nikolaus; Zhang, Song

    2014-06-01

    A structured-light system with a binary defocusing technique has the potential to have more extensive application due to its high speeds, gamma-calibration-free nature, and lack of rigid synchronization requirements between the camera and projector. However, the existing calibration methods fail to achieve high accuracy for a structured-light system with an out-of-focus projector. This paper proposes a method that can accurately calibrate a structured-light system even when the projector is not in focus, making it possible for high-accuracy and high-speed measurement with the binary defocusing method. Experiments demonstrate that our calibration approach performs consistently under different defocusing degrees, and a root-mean-square error of about 73 μm can be achieved with a calibration volume of 150(H) mm×250(W) mm×200(D)mm.

  8. An adaptive scaling and biasing scheme for OFDM-based visible light communication systems.

    Science.gov (United States)

    Wang, Zhaocheng; Wang, Qi; Chen, Sheng; Hanzo, Lajos

    2014-05-19

    Orthogonal frequency-division multiplexing (OFDM) has been widely used in visible light communication systems to achieve high-rate data transmission. Due to the nonlinear transfer characteristics of light emitting diodes (LEDs) and owing the high peak-to-average-power ratio of OFDM signals, the transmitted signal has to be scaled and biased before modulating the LEDs. In this contribution, an adaptive scaling and biasing scheme is proposed for OFDM-based visible light communication systems, which fully exploits the dynamic range of the LEDs and improves the achievable system performance. Specifically, the proposed scheme calculates near-optimal scaling and biasing factors for each specific OFDM symbol according to the distribution of the signals, which strikes an attractive trade-off between the effective signal power and the clipping-distortion power. Our simulation results demonstrate that the proposed scheme significantly improves the performance without changing the LED's emitted power, while maintaining the same receiver structure.

  9. High Performance CMOS Light Detector with Dark Current Suppression in Variable-Temperature Systems.

    Science.gov (United States)

    Lin, Wen-Sheng; Sung, Guo-Ming; Lin, Jyun-Long

    2016-12-23

    This paper presents a dark current suppression technique for a light detector in a variable-temperature system. The light detector architecture comprises a photodiode for sensing the ambient light, a dark current diode for conducting dark current suppression, and a current subtractor that is embedded in the current amplifier with enhanced dark current cancellation. The measured dark current of the proposed light detector is lower than that of the epichlorohydrin photoresistor or cadmium sulphide photoresistor. This is advantageous in variable-temperature systems, especially for those with many infrared light-emitting diodes. Experimental results indicate that the maximum dark current of the proposed current amplifier is approximately 135 nA at 125 °C, a near zero dark current is achieved at temperatures lower than 50 °C, and dark current and temperature exhibit an exponential relation at temperatures higher than 50 °C. The dark current of the proposed light detector is lower than 9.23 nA and the linearity is approximately 1.15 μA/lux at an external resistance RSS = 10 kΩ and environmental temperatures from 25 °C to 85 °C.

  10. Spectral switches of partially coherent light focused by a filter-lens system with chromatic aberration.

    Science.gov (United States)

    Pu, Jixiong; Cai, Chao; Nemoto, Shojiro

    2004-06-01

    It is shown that when partially coherent polychromatic light is focused by a filter-lens system with chromatic aberration, a spectral shift exists in the focused field, and a spectral switch that is defined as a sharp transition of the spectral shift also takes place at some positions of the focused field. The influence of the chromatic aberration of the lens, the coherence of the partially coherent light in the filter (a circular aperture), the radius of the aperture, and the spectral width of the partially coherent light in the aperture on the spectral shift and the spectral switch are investigated in detail. The numerical results show that these parameters affect the spectral shift and the spectral switch significantly. Potential applications of the spectral shift and the spectral switch of the partially coherent light are discussed.

  11. Light Scattering and Thermal Emission by Primitive Dust Particles in Planetary Systems

    CERN Document Server

    Kimura, Hiroshi; Li, Aigen; Lebreton, Jérémy

    2016-01-01

    This review focuses on numerical approaches to deducing the light-scattering and thermal-emission properties of primitive dust particles in planetary systems from astronomical observations. The particles are agglomerates of small grains with sizes comparable to visible wavelength and compositions being mainly magnesium-rich silicates, iron-bearing metals, and organic refractory materials in pristine phases. These unique characteristics of primitive dust particles reflect their formation and evolution around main-sequence stars of essentially solar composition. The development of light-scattering theories has been offering powerful tools to make a thorough investigation of light scattering and thermal emission by primitive dust agglomerates in such a circumstellar environment. In particular, the discrete dipole approximation, the T-matrix method, and effective medium approximations are the most popular techniques for practical use in astronomy. Numerical simulations of light scattering and thermal emission by ...

  12. Excitation of multiple resonances in 1D Anderson localized systems for efficient light amplification.

    Science.gov (United States)

    Choi, Seung Ho; Byun, Kyung Min; Kim, Young L

    2015-03-01

    Excitation of hybridized multiple resonances can be an effective route for coherent light generation in irregular 1D systems larger than the localization length of light. Necklace states are often considered to have nonlocalized states. However, we propose that some hybridized/coupled states can have high-resonant tunneling with spatially extended fields. If strong localization properties are preserved in hybridized resonances, the excitation of such states allows for deposition of the excitation energy deep into the structure and spatial overlap with local gain regions. This result could allow for better utilizing hybridized resonances in biological or natural photonic systems.

  13. Versatile light-emitting-diode-based spectral response measurement system for photovoltaic device characterization.

    Science.gov (United States)

    Hamadani, Behrang H; Roller, John; Dougherty, Brian; Yoon, Howard W

    2012-07-01

    An absolute differential spectral response measurement system for solar cells is presented. The system couples an array of light emitting diodes with an optical waveguide to provide large area illumination. Two unique yet complementary measurement methods were developed and tested with the same measurement apparatus. Good agreement was observed between the two methods based on testing of a variety of solar cells. The first method is a lock-in technique that can be performed over a broad pulse frequency range. The second method is based on synchronous multifrequency optical excitation and electrical detection. An innovative scheme for providing light bias during each measurement method is discussed.

  14. A 3D acquisition system combination of structured-light scanning and shape from silhouette

    Institute of Scientific and Technical Information of China (English)

    Changku Sun; Li Tao; Peng Wang; Li He

    2006-01-01

    @@ A robust and accurate three dimensional (3D) acquisition system is presented, which is a combination of structured-light scanning and shape from silhouette. Using common world coordinate system, two groups of point data can be integrated into the final complete 3D model without any integration and registration algorithm. The mathematics model of structured-light scanning is described in detail, and the shape from silhouette algorithm is introduced as well. The complete 3D model of a cup with a handle is obtained successfully by the proposed technique. At last the measurement on a ball bearing is performed, with the measurement precision better than 0.15 mm.

  15. TW Laser system for Thomson scattering X-ray light source at Tsinghua University

    Institute of Scientific and Technical Information of China (English)

    YAN Li-Xin; DU Ying-Chao; DU Qiang; LI Ren-Kai; HUA Jian-Fei; HUANG Wen-Hui; TANG Chuan-Xiang

    2009-01-01

    A TW(Tera Watt)laser system based on Ti:sapphire mainly for the Tsinghua Thomson scattering X-ray light source(TTX)is being built.Both UV(ultraviolet)laser pulse for driving the photocathode radiofrequency(RF)gun and the IR(infrared)laser pulse as the electron-beam-scattered-light are provided by the system.Efforts have also been made in laser pulse shaping and laser beam transport to optimize the high-brightness electron beam production by the photocathode RF gun.

  16. Pixel-wise absolute phase unwrapping using geometric constraints of structured light system.

    Science.gov (United States)

    An, Yatong; Hyun, Jae-Sang; Zhang, Song

    2016-08-08

    This paper presents a method to unwrap phase pixel by pixel by solely using geometric constraints of the structured light system without requiring additional image acquisition or another camera. Specifically, an artificial absolute phase map, Φmin, at a given virtual depth plane z = zmin, is created from geometric constraints of the calibrated structured light system; the wrapped phase is pixel-by-pixel unwrapped by referring to Φmin. Since Φmin is defined in the projector space, the unwrapped phase obtained from this method is absolute for each pixel. Experimental results demonstrate the success of this proposed novel absolute phase unwrapping method.

  17. Adaptation of light-harvesting systems of Arthrospira platensis to light conditions, probed by time-resolved fluorescence spectroscopy.

    Science.gov (United States)

    Akimoto, Seiji; Yokono, Makio; Hamada, Fumiya; Teshigahara, Ayaka; Aikawa, Shimpei; Kondo, Akihiko

    2012-08-01

    Cyanobacteria change the quantity and/or quality of their pigment-protein complexes in response to light conditions. In the present study, we analyzed excitation relaxation dynamics in the cyanobacterium, Arthrospira (Spirulina) platensis, grown under lights exhibiting different spectral profiles, by means of steady-state absorption and picosecond time-resolved fluorescence spectroscopies. It was found that F760, which is the PSI red-chlorophyll characteristic of A. platensis, contributes to slower energy-transfer phase in the PSI of A. platensis. Excitation energy transfers in phycobilisome and those from PSII to PSI were modified depending on the light quality. Existence of quencher was suggested in PSI of the blue-light grown cells. Phycobilisomes in the green-light grown cells and the far-red-light grown cells transferred excitation energy from phycobilisome to chlorophyll without loss of energy. In these cells, excitation energy was shared between two photosystems. Fast energy transfer was established in phycobilisome under the yellow-light condition where only the phycobilisome can absorb the cultivation light. Differences in light-harvesting and energy-transfer processes under different cultivation-light conditions are discussed. This article is part of a Special Issue entitled: Photosynthesis Research for Sustainability: from Natural to Artificial.

  18. Visible-light system for detecting doxorubicin contamination on skin and surfaces.

    Science.gov (United States)

    Van Raalte, J; Rice, C; Moss, C E

    1990-05-01

    A portable system that uses fluorescence stimulated by visible light to identify doxorubicin contamination on skin and surfaces was studied. When activated by violet-blue light in the 465-nm range, doxorubicin fluoresces, emitting orange-red light in the 580-nm range. The light source to stimulate fluorescence was a slide projector with a filter to selectively pass short-wave (blue) visible light. Fluorescence was both observed visually with viewing spectacles and photographed. Solutions of doxorubicin in sterile 0.9% sodium chloride injection were prepared in nine standard concentrations ranging from 2 to 0.001 mg/mL. Droplets of each admixture were placed on stainless steel, laboratory coat cloth, pieces of latex examination glove, bench-top absorbent padding, and other materials on which antineoplastics might spill or leak. These materials then were stored for up to eight weeks and photographed weekly. The relative ability of water, household bleach, hydrogen peroxide solution, and soap solution to deactivate doxorubicin was also measured. Finally, this system was used to inspect the antineoplastic-drug preparation and administration areas of three outpatient cancer clinics for doxorubicin contamination. Doxorubicin fluorescence was easily detectable with viewing spectacles when a slide projector was used as the light source. The photographic method was sensitive for doxorubicin concentrations from 2.0 to 0.001 mg/mL. Immersion of study materials in bleach for one minute eliminated detectable fluorescence. Doxorubicin contamination is detectable for at least eight weeks in the ambient environment. Probable doxorubicin contamination was detected in two of the three clinics surveyed. A safe, portable system that uses fluorescence stimulated by visible light is a sensitive method for detecting doxorubicin on skin and surfaces.

  19. Stray light analysis in the TV system for tracking and measuring

    Science.gov (United States)

    Cao, Lei; Chen, Hong-bin; Qiu, Qi; Ren, Ge; Jiang, Yang; Qi, Bo

    2014-08-01

    According to the technical features and requirements of the television imaging system for tracking and measuring, we designed a TV system with focal length of 2800mm, F/11.7 and 2ω(FOV) of 14.2'. The system is compact and easy to fabricate and align, with good image quality. Meanwhile, we performed stray light analysis with ASAP optical software, described stray light suppression techniques used in the TV for tracking and measuring, proposed a method to determine optical properties of the system components and parameters of the scattering model reasonably. We calculated the PST curve of the system for incident angle from -45° to 45°. The results show that when the off-axis angle is larger than the critical incident angle of the sun, PST value is less than 10-8.

  20. Illumination Effect of Laser Light in Foggy Objects Using an Active Imaging System

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Seong-Ouk; Park, Seung-Kyu; Ahn, Yong-Jin; Baik, Sung-Hoon; Choi, Young-Soo; Jeong, Kyung-Min [KAERI, Daejeon (Korea, Republic of)

    2015-05-15

    Active imaging techniques usually provide improved image information when compared to passive imaging techniques. Active vision is a direct visualization technique using an artificial illuminant. Range-gated imaging (RGI) technique is one of active vision technologies. The RGI technique extracts vision information by summing time sliced vision images. In the RGI system, objects are illuminated for ultra-short time by a high intensity illuminant and then the light reflected from objects is captured by a highly sensitive image sensor with the exposure of ultra-short time. The Range-gated imaging is an emerging technology in the field of surveillance for security application, especially in the visualization of darken night or foggy environment. Although RGI viewing was discovered in the 1960's, this technology is currently more applicable by virtue of the rapid development of optical and sensor technologies, such as highly sensitive imaging sensor and ultra-short pulse laser light. Especially, this system can be adopted in robot-vision system by virtue of the compact system configuration. During the past decades, several applications of this technology have been applied in target recognition and in harsh environments, such as fog, underwater vision. Also, this technology has been demonstrated range imaging based on range-gated imaging. Laser light having a short pulse width is usually used for the range-gated imaging system. In this paper, an illumination effect of laser light in foggy objects is studied using a range-gated imaging system. The used imaging system consists of an ultra-short pulse (0.35 ns) laser light and a gated imaging sensor. The experiment is carried out to monitor objects in a box filled by fog. In this paper, the effects by fog particles in range-gated imaging technique are studied. Edge blurring and range distortion are the generated by fog particles.

  1. The effect of traffic light on accident probability in open and periodic boundaries system

    Science.gov (United States)

    Mhirech, Abdelaziz; Alaoui-Ismaili, Assia

    2015-09-01

    In this paper we numerically study the dependence of car accident probability Pac, per site and per time step on cycle time T of traffic light, both in open and periodic boundaries system. In this study one traffic light is placed in the middle of the system. This work is based on Nagel and Schreckenberg (NaSch) model (Nagel and Schreckenberg (1992)) in parallel dynamics. The Pac dependence on T and the (α, β) phase diagrams are established. α and β are the injecting and extracting rates of cars in the traffic lane respectively. The increase of the cycle time light T causes an important decrease of the accident probability Pac both in the open and periodic cases.

  2. An Efficient Light-Inducible P53 Expression System for Inhibiting Proliferation of Bladder Cancer Cell

    Science.gov (United States)

    Lin, Fan; Dong, Liang; Wang, Weiming; Liu, Yuchen; Huang, Weiren; Cai, Zhiming

    2016-01-01

    Optogenetic gene expression systems enable spatial-temporal modulation of gene transcription and cell behavior. Although applications in biomedicine are emerging, the utility of optogenetic gene switches remains elusive in cancer research due to the relative low gene activation efficiency. Here, we present an optimized CRISPR-Cas9-based light-inducible gene expression device that controls gene transcription in a dose-dependent manner. To prove the potential utility of this device, P53 was tested as a functional target in the bladder cancer cell models. It was illustrated that the light-induced P53 inhibited proliferation of 5637 and UMUC-3 cell effectively. The “light-on” gene expression system may demonstrate a novel therapeutic strategy for bladder cancer intervention. PMID:27766041

  3. Cross Talk between a Fungal Blue-Light Perception System and the Cyclic AMP Signaling Pathway

    Science.gov (United States)

    Casas-Flores, Sergio; Rios-Momberg, Mauricio; Rosales-Saavedra, Teresa; Martínez-Hernández, Pedro; Olmedo-Monfil, Vianey; Herrera-Estrella, Alfredo

    2006-01-01

    Blue light regulates many physiological and developmental processes in fungi. In Trichoderma atroviride the complex formed by the BLR-1 and BLR-2 proteins appears to play an essential role as a sensor and transcriptional regulator in photoconidiation. Here we demonstrate that the BLR proteins are necessary for carbon deprivation induced conidiation, even in the absence of light, pointing to the existence of an unprecedented cross talk between light and carbon sensing. Further, in contrast to what has been found in all other fungal systems, clear BLR-independent blue-light responses, including the activation of protein kinase A (PKA) and the regulation of gene expression, were found. Expression of an antisense version of the pkr-1 gene, encoding the regulatory subunit of PKA, resulted in a nonsporulating phenotype, whereas overexpression of the gene produced colonies that conidiate even in the dark. In addition, overexpression of pkr-1 blocked the induction of early light response genes. Thus, our data demonstrate that PKA plays an important role in the regulation of light responses in Trichoderma. Together, these observations suggest that the BLR complex plays a general role in sensing environmental cues that trigger conidiation and that such a role can be separated from its function as a transcription factor. PMID:16524905

  4. An experiment on the color rendering of different light sources

    Science.gov (United States)

    Fumagalli, Simonetta; Bonanomi, Cristian; Rizzi, Alessandro

    2013-02-01

    The color rendering index (CRI) of a light source attempts to measure how much the color appearance of objects is preserved when they are illuminated by the given light source. This problem is of great importance for various industrial and scientific fields, such as lighting architecture, design, ergonomics, etc. Usually a light source is specified through the Correlated Color Temperature or CCT. However two (or more) light sources with the same CCT but different spectral power distribution can exist. Therefore color samples viewed under two light sources with equal CCTs can appear different. Hence, the need for a method to assess the quality of a given illuminant in relation to color. Recently CRI has had a renewed interest because of the new LED-based lighting systems. They usually have a color rendering index rather low, but good preservation of color appearance and a pleasant visual appearance (visual appeal). Various attempts to develop a new color rendering index have been done so far, but still research is working for a better one. This article describes an experiment performed by human observers concerning the appearance preservation of color under some light sources, comparing it with a range of available color rendering indices.

  5. Neural Summation in the Hawkmoth Visual System Extends the Limits of Vision in Dim Light.

    Science.gov (United States)

    Stöckl, Anna Lisa; O'Carroll, David Charles; Warrant, Eric James

    2016-03-21

    Most of the world's animals are active in dim light and depend on good vision for the tasks of daily life. Many have evolved visual adaptations that permit a performance superior to that of manmade imaging devices [1]. In insects, a major model visual system, nocturnal species show impressive visual abilities ranging from flight control [2, 3], to color discrimination [4, 5], to navigation using visual landmarks [6-8] or dim celestial compass cues [9, 10]. In addition to optical adaptations that improve their sensitivity in dim light [11], neural summation of light in space and time-which enhances the coarser and slower features of the scene at the expense of noisier finer and faster features-has been suggested to improve sensitivity in theoretical [12-14], anatomical [15-17], and behavioral [18-20] studies. How these summation strategies function neurally is, however, presently unknown. Here, we quantified spatial and temporal summation in the motion vision pathway of a nocturnal hawkmoth. We show that spatial and temporal summation combine supralinearly to substantially increase contrast sensitivity and visual information rate over four decades of light intensity, enabling hawkmoths to see at light levels 100 times dimmer than without summation. Our results reveal how visual motion is calculated neurally in dim light and how spatial and temporal summation improve sensitivity while simultaneously maximizing spatial and temporal resolution, thus extending models of insect motion vision derived predominantly from diurnal flies. Moreover, the summation strategies we have revealed may benefit manmade vision systems optimized for variable light levels [21].

  6. Design of a light delivery system for the photodynamic treatment of the Crohn's disease

    Science.gov (United States)

    Gabrecht, Tanja; Borle, Francois; van den Bergh, Hubert; Michetti, Pierre; Ortner, Maria-Anna; Wagnières, Georges

    2007-07-01

    Crohn's disease is an inflammatory bowel disease originating from an overwhelming response of the mucosal immune system. Low dose photodynamic therapy (PDT) may modify the mucosal immune response and thus serve as a therapy for Crohn's disease. Most patients with Crohn's disease show inflammatory reactions in the terminal ileum or colon where PDT treatment is feasible by low-invasive endoscopic techniques. However, the tube like geometry of the colon, it's folding, and the presences of multiple foci of Crohn's lesions along the colon require the development of adequate light delivery techniques. We present a prototype light delivery system for endoscopic clinical PDT in patients with Crohn's disease. The system is based on a cylindrical light diffuser inserted into a diffusing balloon catheter. Homogenous irradiation is performed with a 4 W diode laser at 635 nm. Light dosimetry is performed using a calibrated integrating sphere. The system can be used with conventional colonoscopes and colonovideoscopes having a 3.8 mm diameter working channel. The feasibility of PDT in colon with our prototype was demonstrated in first clinical trials.

  7. Particle smoothing for solving ambiquity problems in one-shot structured light systems

    NARCIS (Netherlands)

    Heijden, van der F.; Berendsen, F.F.; Spreeuwers, L.J.; Schippers, E.

    2011-01-01

    One-shot structured light systems for 3D depth reconstruction often use a periodic illumination pattern. Finding corresponding points in the image and projector plane, needed for a triangulation, boils down to phase estimation. The 2πN ambiguities in the phase cause ambiguities in the reconstructed

  8. 46 CFR 25.45-1 - Heating and lighting systems on vessels carrying passengers for hire.

    Science.gov (United States)

    2010-10-01

    ...) Alcohol, solid, (2) Alcohol, liquid, combustible, (3) Fuel oil, No. 1, No. 2, or No. 3, (4) Kerosene, (5.../4” to form a pan. (2) Fuel tanks must be— (i) Separated from the stove that they serve; (ii) Mounted... on vessels carrying passengers for hire. (a) No fuel may be used in any heating or lighting system...

  9. Quantum coherence controls the charge separation in a prototypical artificial light harvesting system

    Directory of Open Access Journals (Sweden)

    Schramm H.

    2013-03-01

    Full Text Available Ultrafast spectroscopy and quantum-dynamics simulations of an artificial supramolecular light-harvesting system — a supramolecular triad - provide strong evidence that the quantum-correlated wavelike motion of electrons and nuclei on a timescale of few tens of femtoseconds governs the ultrafast electronic charge transfer.

  10. Development of a Hybrid Atomic Force Microscopic Measurement System Combined with White Light Scanning Interferometry

    Directory of Open Access Journals (Sweden)

    Xiaotang Hu

    2011-12-01

    Full Text Available A hybrid atomic force microscopic (AFM measurement system combined with white light scanning interferometry for micro/nanometer dimensional measurement is developed. The system is based on a high precision large-range positioning platform with nanometer accuracy on which a white light scanning interferometric module and an AFM head are built. A compact AFM head is developed using a self-sensing tuning fork probe. The head need no external optical sensors to detect the deflection of the cantilever, which saves room on the head, and it can be directly fixed under an optical microscopic interferometric system. To enhance the system’s dynamic response, the frequency modulation (FM mode is adopted for the AFM head. The measuring data can be traceable through three laser interferometers in the system. The lateral scanning range can reach 25 mm × 25 mm by using a large-range positioning platform. A hybrid method combining AFM and white light scanning interferometry is proposed to improve the AFM measurement efficiency. In this method, the sample is measured firstly by white light scanning interferometry to get an overall coarse morphology, and then, further measured with higher resolution by AFM. Several measuring experiments on standard samples demonstrate the system’s good measurement performance and feasibility of the hybrid measurement method.

  11. Multireference excitation energies for bacteriochlorophylls A within light harvesting system 2

    DEFF Research Database (Denmark)

    Anda, Andre; Hansen, Thorsten; De Vico, Luca

    2016-01-01

    Light-harvesting system 2 (LH2) of purple bacteria is one of the most popular antenna complexes used to study Nature's way of collecting and channeling solar energy. The dynamics of the absorbed energy is probed by ultrafast spectroscopy. Simulation of these experiments relies on fitting a range...

  12. Light-shift calculation in the ns-states of hydrogenic systems

    NARCIS (Netherlands)

    Yakhontov, [No Value; Jungmann, K

    1996-01-01

    We present the results of the light-shift calculations in the as-states of hydrogenic systems in the presence of a weak laser field. This is done by means of analytical calculations of the scalar dynamic polarizabilities (DP) of the corresponding levels. In contrast to the usual technique, our analy

  13. 76 FR 47178 - Energy Efficiency Program: Test Procedure for Lighting Systems (Luminaires)

    Science.gov (United States)

    2011-08-04

    ... 1904-AC50 Energy Efficiency Program: Test Procedure for Lighting Systems (Luminaires) AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION: Request for Information. SUMMARY... Energy Efficiency and Renewable Energy, Building Technologies Program, EE-2J, 1000 Independence...

  14. Solar lanterns or solar home lighting systems - Community preferences in East Timor

    Energy Technology Data Exchange (ETDEWEB)

    Bond, M.; Aye, Lu; Fuller, R.J. [Renewable Energy and Energy Efficiency Group, Department of Civil and Environmental Engineering, The University of Melbourne, Victoria 3010 (Australia)

    2010-05-15

    Access to electrification in rural areas of East Timor is extremely limited with as few as 5% of rural households connected to electricity. The government of East Timor intends to increase rural access to electricity significantly in the coming decade. The introduction of small PV systems is envisaged for many households in the most remote areas. Several agencies have piloted the introduction of small solar home systems (SHS) and solar lanterns. In the Railaco sub-district of East Timor, some 1000 households have experience of using either SHS and/or solar lanterns and are in a unique position to indicate a preference regarding these forms of PV lighting technology. This paper reports on a survey of 76 households in Railaco investigating experience with PV lighting systems. Results of the survey indicate a strong preference by users for SHS rather than lanterns. The preference for SHS arose from a range of factors including: a perception of better light quality; ability to illuminate the whole house; reduced risk of damage to the PV equipment; and longer duration of nightly operation. The research indicates that where a single PV lighting system is provided, users are likely to prefer SHS to solar lanterns. (author)

  15. Session IV. Problem Solving. Vehicle lighting system. Four steps in glare reduction.

    NARCIS (Netherlands)

    Schreuder, D.A.

    1972-01-01

    A number of proposals are described that may help to reduce glare. The systems are either only a partial improvement, or they are expensive, or their introduction raises severe problems. One solution, already widely in use, is applica- tion of overhead lighting. In order to really improve the situa

  16. Description of light charged particle multiplicities in the framework of dinuclear system model

    Directory of Open Access Journals (Sweden)

    Antonenko N.V.

    2012-12-01

    Full Text Available In the framework of dinuclear system (DNS model we calculate the light charged particle (LCP multiplicities produced in fusion and quasifission reactions and their kinetic energy spectra. Calculations indicate that with increasing bombarding energy the ratio of LCP multiplicity from fragments MFF to corresponding LCP multiplicity from compound nucleus (CN MCN strongly increases.

  17. ChR2 transgenic animals in peripheral sensory system: Sensing light as various sensations.

    Science.gov (United States)

    Ji, Zhi-Gang; Wang, Hongxia

    2016-04-01

    Since the introduction of Channelrhodopsin-2 (ChR2) to neuroscience, optogenetics technology was developed, making it possible to activate specific neurons or circuits with spatial and temporal precision. Various ChR2 transgenic animal models have been generated and are playing important roles in revealing the mechanisms of neural activities, mapping neural circuits, controlling the behaviors of animals as well as exploring new strategy for treating the neurological diseases in both central and peripheral nervous system. An animal including humans senses environments through Aristotle's five senses (sight, hearing, smell, taste and touch). Usually, each sense is associated with a kind of sensory organ (eyes, ears, nose, tongue and skin). Is it possible that one could hear light, smell light, taste light and touch light? When ChR2 is targeted to different peripheral sensory neurons by viral vectors or generating ChR2 transgenic animals, the animals can sense the light as various sensations such as hearing, touch, pain, smell and taste. In this review, we focus on ChR2 transgenic animals in the peripheral nervous system. Firstly the working principle of ChR2 as an optogenetic actuator is simply described. Then the current transgenic animal lines where ChR2 was expressed in peripheral sensory neurons are presented and the findings obtained by these animal models are reviewed.

  18. High luminous flux from single crystal phosphor-converted laser-based white lighting system

    KAUST Repository

    Cantore, Michael

    2015-12-14

    The efficiency droop of light emitting diodes (LEDs) with increasing current density limits the amount of light emitted per wafer area. Since low current densities are required for high efficiency operation, many LED die are needed for high power white light illumination systems. In contrast, the carrier density of laser diodes (LDs) clamps at threshold, so the efficiency of LDs does not droop above threshold and high efficiencies can be achieved at very high current densities. The use of a high power blue GaN-based LD coupled with a single crystal Ce-doped yttrium aluminum garnet (YAG:Ce) sample was investigated for white light illumination applications. Under CW operation, a single phosphor-converted LD (pc-LD) die produced a peak luminous efficacy of 86.7 lm/W at 1.4 A and 4.24 V and a peak luminous flux of 1100 lm at 3.0 A and 4.85 V with a luminous efficacy of 75.6 lm/W. Simulations of a pc-LD confirm that the single crystal YAG:Ce sample did not experience thermal quenching at peak LD operating efficiency. These results show that a single pc-LD die is capable of emitting enough luminous flux for use in a high power white light illumination system.

  19. Design of visible light communication system for maintaining uniform data rate

    Science.gov (United States)

    Sung, Jiun-Yu; Lin, Wan-Feng; Wu, Yu-Fu; Chow, Chi-Wai; Yeh, Chien-Hung

    2014-09-01

    Light-emitting diode (LED) is gradually replacing the fluorescent lamp for lighting. Higher modulation bandwidth of LEDs makes the additional application of visible light communication (VLC) possible. Every location of a VLC system should be provided by equal data rate for smooth communication. However, locations away from the LED lamp have less power. These low-power locations have lower signal-to-noise ratio (SNR); and hence lower data rate can be achieved. For achieving high capacity VLC, strategies should be adequately provided to mitigate this problem. Moreover, for some real-time continuous applications, such as video and voice, latency reduction plan should also be considered. In this paper, an orthogonal frequency-division multiplexing access (OFDMA) based system was proposed to solve the above problem. Because we do not use time-division multiplexing access (TDMA) based system, the latency issue can be reduced. The OFDMA based system is also beneficial for large scale operation because the user bandwidth is not reduced by TDM mechanism. Signal-to-noise-plus-interference ratio (SNIR) distribution of the VLC system is designed to ensure uniform and optimal system capacity. Discrete multi-tone (DMT) is used for this VLC system. The DMT subcarriers are bit-loaded depending on the LED frequency response. More subcarriers are allocated for communication at low SNIR locations. Hence, nearly equal data rate can be provided everywhere. Demonstration of 17 Mb/s/LED data rate was provided.

  20. The design of common aperture and multi-band optical system based on day light telescope

    Science.gov (United States)

    Chen, Jiao; Wang, Ling; Zhang, Bo; Teng, Guoqi; Wang, Meng

    2017-02-01

    As the development of electro-optical weapon system, the technique of common path and multi-sensor are used popular, and becoming a trend. According to the requirement of miniaturization and lightweight for electro-optical stabilized sighting system, a day light telescope/television viewing-aim system/ laser ranger has been designed in this thesis, which has common aperture. Thus integration scheme of multi-band and common aperture has been adopted. A day light telescope has been presented, which magnification is 8, field of view is 6°, and distance of exit pupil is more than 20mm. For 1/3" CCD, television viewing-aim system which has 156mm focal length, has been completed. In addition, laser ranging system has been designed, with 10km raging distance. This paper outlines its principle which used day light telescope as optical reference of correcting the optical axis. Besides, by means of shared objective, reserved image with inverting prism and coating beam-splitting film on the inclined plane of the cube prism, the system has been applied to electro-optical weapon system, with high-resolution of imaging and high-precision ranging.

  1. Hybrid artificial photosynthetic systems comprising semiconductors as light harvesters and biomimetic complexes as molecular cocatalysts.

    Science.gov (United States)

    Wen, Fuyu; Li, Can

    2013-11-19

    Solar fuel production through artificial photosynthesis may be a key to generating abundant and clean energy, thus addressing the high energy needs of the world's expanding population. As the crucial components of photosynthesis, the artificial photosynthetic system should be composed of a light harvester (e.g., semiconductor or molecular dye), a reduction cocatalyst (e.g., hydrogenase mimic, noble metal), and an oxidation cocatalyst (e.g., photosystem II mimic for oxygen evolution from water oxidation). Solar fuel production catalyzed by an artificial photosynthetic system starts from the absorption of sunlight by the light harvester, where charge separation takes place, followed by a charge transfer to the reduction and oxidation cocatalysts, where redox reaction processes occur. One of the most challenging problems is to develop an artificial photosynthetic solar fuel production system that is both highly efficient and stable. The assembly of cocatalysts on the semiconductor (light harvester) not only can facilitate the charge separation, but also can lower the activation energy or overpotential for the reactions. An efficient light harvester loaded with suitable reduction and oxidation cocatalysts is the key for high efficiency of artificial photosynthetic systems. In this Account, we describe our strategy of hybrid photocatalysts using semiconductors as light harvesters with biomimetic complexes as molecular cocatalysts to construct efficient and stable artificial photosynthetic systems. We chose semiconductor nanoparticles as light harvesters because of their broad spectral absorption and relatively robust properties compared with a natural photosynthesis system. Using biomimetic complexes as cocatalysts can significantly facilitate charge separation via fast charge transfer from the semiconductor to the molecular cocatalysts and also catalyze the chemical reactions of solar fuel production. The hybrid photocatalysts supply us with a platform to study the

  2. Long-range visible light communication system based on LED collimating lens

    Science.gov (United States)

    Chen, Yingcong; Wen, Shangsheng; Wu, Yuxiang; Ren, Yuanyuan; Guan, Weipeng; Zhou, Yunlin

    2016-10-01

    An advanced visible light communication (VLC) system is proposed for long-range VLC, such as marine communication. The design of the system is conducted into two parts. Firstly, we design and optimize a collimating lens for the optical antenna by using Taguchi method. The lighting effects and optical power of the receiving end in different distances are simulated by TracePro software. Then, the long-range VLC channel is reconstructed by integrating the influence of the atmospheric attenuation and frequency response. The performance of the OOK coding VLC system is tested by Matlab software. The results show that: the emitting angle of the optimized collimating lens is 1.7°. By using 1 W LED and collimating lens as an optical antenna, the system can achieve a data rate of 210 Mbit/s at a bit error rate of 10-3 in 90 m.

  3. Gain-assisted superluminal light propagation through a Bose-Einstein condensate cavity system

    Science.gov (United States)

    Hamide Kazemi, S.; Ghanbari, S.; Mahmoudi, M.

    2016-01-01

    The propagation of a probe laser field in a cavity optomechanical system with a Bose-Einstein condensate is studied. The transmission properties of the system are investigated and it is shown that the group velocity of the probe pulse field can be controlled by Rabi frequency of the pump laser field. The effect of the decay rate of the cavity photons on the group velocity is studied and it is demonstrated that for small values of the decay rates, the light propagation switches from subluminal to superluminal just by changing the Rabi frequency of the pump field. Then, the gain-assisted superluminal light propagation due to the cross-Kerr nonlinearity is established in cavity optomechanical system with a Bose-Einstein condensate. Such behavior can not appear in the pump-probe two-level atomic systems in the normal phase. We also find that the amplification is achieved without inversion in the population of the quantum energy levels.

  4. Scalar-tensor propagation of light in the inner solar system at the millimetric level

    CERN Document Server

    Minazzoli, Olivier

    2010-01-01

    In a recent paper [1], motivated by forthcoming space experiments involving propagation of light in the Solar System, we have proposed an extention of the IAU metric equations at the c-4 level in General Relativity. However, scalar-tensor theories may induce corrections numerically comparable to the c-4 general relativistic terms. Accordingly, one first proposes in this paper an extension of [1] to the scalar-tensor case. The case of a hierarchized system (such as the Solar system) is emphasized. In this case, the relevant metric solution is proposed. Then, the geodesic solution relevant for propagation of light in the inner solar system at the millimetric level is given in explicit form.

  5. Light redirecting system using sine-wave based panels for dense urban areas

    Science.gov (United States)

    Mohamed, Mohamed W. N.; Mashaly, Islam A.; Mohamed, Osama N.; El-Henawy, Sally I.; Galal, Ola; Taha, Iman; Nassar, Khaled; Safwat, Amr M. E.

    2014-09-01

    Cities and towns around the world are becoming more condensed due to the shrinking amount of buildable areas, which significantly reduces the amount of light that occupants have access to. This lack of natural lighting results in health, safety and quality of life degradation. This paper presents a new technique of transmitting sunlight downward into narrow alleys and streets, by using a daylighting guiding acrylic panel that is capable of changing the direction and distribution of the incident light. The core of the proposed daylight guidance system is made up of light transmission panels with high quality. The corrugations have sine wave shaped cross-section so that the panel functions as an optical diffuser perpendicular to the direction of sunlight propagation. The day lighting system consists of the corrugated panels and a lattice frame, which supports the panel. The proposed system is to be mounted on the building roof facing the sun so as to redirect the incident sunlight downward into the narrow alleys or streets. Since building sizes and orientations are different the frame is arranged such that substantially deep light penetration and high luminance level can be achieved. Simulation results show that the proposed panel improves the illuminance values by more than 200% and 400% in autumn and winter, respectively, provides fan-out angle that exceeds 80° for certain solar altitudes and the transmitted power percentage varies from 40% to 90% as the solar altitude varies from 10° to 80°. Experimental results are in a good agreement with the simulations.

  6. Test of candidate light distributors for the muon (g$-$2) laser calibration system

    CERN Document Server

    Anastasi, A; Baffigi, F; Cantatore, G; Cauz, D; Corradi, G; Dabagov, S; Di Sciascio, G; Di Stefano, R; Ferrari, C; Fienberg, A T; Fioretti, A; Fulgentini, L; Gabbanini, C; Gizzi, L A; Hampai, D; Hertzog, D W; Iacovacci, M; Karuza, M; Kaspar, J; Koester, P; Labate, L; Mastroianni, S; Moricciani, D; Pauletta, G; Santi, L; Venanzoni, G

    2015-01-01

    The new muon (g-2) experiment E989 at Fermilab will be equipped with a laser calibration system for all the 1296 channels of the calorimeters. An integrating sphere and an alternative system based on an engineered diffuser have been considered as possible light distributors for the experiment. We present here a detailed comparison of the two based on temporal response, spatial uniformity, transmittance and time stability.

  7. Design Considerations for a Water Treatment System Utilizing Ultra-Violet Light Emitting Diodes

    Science.gov (United States)

    2014-03-27

    industry use for UV fluorescent bulb type water disinfection systems (Aquionics, 2013). Shorter wavelength LEDs (240 nm) were shown to be more...is in its infancy and research as it applies to UV water treatment is required to advance knowledge for practical application. This thesis focused...on two subjects. First, the design, fabrication, and operation of a water treatment reaction system utilizing Ultra-Violet ( UV ) Light Emitting

  8. Compact transmission system using single-sideband modulation of light for quantum cryptography.

    Science.gov (United States)

    Duraffourg, L; Merolla, J M; Goedgebuer, J P; Mazurenko, Y; Rhodes, W T

    2001-09-15

    We report a new transmission that can be used for quantum key distribution. The system uses single-sideband-modulated light in an implementation of the BB84 quantum cryptography protocol. The system is formed by two integrated unbalanced Mach-Zehnder interferometers and is based on interference between phase-modulated sidebands in the spectral domain. Experiments show that high interference visibility can be obtained.

  9. NIR-LEDs lighting system for enhancing Brix distinction with saving energy to agricultural products

    Science.gov (United States)

    Lee, Kwang-Hoon; Lee, Dong-Kil; Kim, Yang-Gyu; Park, Ahn-Jin; Jang, Won-Geun; Park, Youngsik

    2014-05-01

    In this paper, the sugar content prediction determination system in optical non-contact type based on the near infrared light emitting diode (NIR-LED) lamp is proposed. As the result NIR-LED lamp reduced 86% of the energy consumption compared to the case of Halogen lamp in the same process of sugar content determination. And the result of prediction of sugar content by NIR-LED lamp is shown to as near the same level of Halogen lamp system.

  10. INTELLECTUAL SENSOR SYSTEM OF SOIL LIGHT-COLOR CONTROL: REALIZATION OF SELF-SUSTAINABILITY FUNCTIONS

    Directory of Open Access Journals (Sweden)

    V. M. Koleshko

    2011-01-01

    Full Text Available An intellectual sensor module of soil light-color control designed for an accurate agriculture technology which comprises functions of self-diagnostics, self-corrections and self-attestation. Circuit diagrams sensor module components have been developed on the basis of a micro-controller, a photo-diode driver, an interface integrated circuit and a receiving block of optical pulses. An algorithm and an operational program of a microcontroller have been devised for executing control over light pulses, processing of  photoelectric receptor signals, data receive-transmit operations, correction of sensitive elements, diagnostics of system failure and attestation of control results.

  11. Adaptive imaging system with spatial light modulator for robust shape measurement of partially specular objects.

    Science.gov (United States)

    Jeong, Joongki; Kim, Min Young

    2010-12-20

    In imaging systems, when specular surfaces responding sensitively to varying illumination conditions are imaged on groups of CCD pixels using imaging optics, the obtained image usually suffers from pixel saturation, resulting in smearing or blooming phenomena. These problems are then serious obstacles when applying structured light-based optical profiling methods to the shape measurement of general objects with partially specular surfaces. Therefore, this paper combines a phase-based profiling system with an with an adaptive spatial light modulator in the imaging part for measuring the three-dimensional shapes of objects with an advanced dynamic range. The use of a spatial light modulator in front of a CCD camera prevents the image sensor from being saturated, as the pixel transmittance is controlled by monitoring the input images and providing modulator feedback signals over time and space. When using the proposed system, since the projected fringes are effectively imaged on the CCD without any pixel saturation, phase information according to the object's shape can be correctly extracted from non-saturated images. The configuration of the proposed system and transmittance control scheme are explained in detail, plus the performance is verified through a series of experiments, in which phase information was successfully extracted from areas that are not normally measurable due to saturation. Based on the results, the proposed shape measurement system showed a more advanced adaptive dynamic range when compared with a conventional system.

  12. Verification and analysis of stray light in high-power laser system

    Science.gov (United States)

    Huang, PingXian; Cen, Zhaofeng; Li, Xiaotong; Jin, Yuan

    2014-11-01

    In the high-power laser system, the stray light which is generated by the surface's residual reflection of optical elements and the multi-pass transmission in the system will lead to temperature increase in part of the system, the optical elements deformation and damage, distortion of wave-front and change of the beam's divergence angle, which seriously influence the beam's quality and propagation properties and damage the components in the system. So, it is very important to use the relevant software to analyze the stray light rigorously because the reliability and precision of the software is the guarantee of reliable results. Through two types of software we performed the simulation of the stray light in the system, including ghost's distribution in the case of different states of rotating defocusing, beam's pointing. Simultaneously, the impact of processing and assembling errors is analyzed in details. We built a specialized experiment to verify the reliability of results of the software and the related parameters of system are conveniently measured with the device.

  13. Fundamental algorithm and computational codes for the light beam propagation in high power laser system

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The fundamental algorithm of light beam propagation in high powerlaser system is investigated and the corresponding computational codes are given. It is shown that the number of modulation ring due to the diffraction is related to the size of the pinhole in spatial filter (in terms of the times of diffraction limitation, i.e. TDL) and the Fresnel number of the laser system; for the complex laser system with multi-spatial filters and free space, the system can be investigated by the reciprocal rule of operators.

  14. [Methodological approaches to the hygienic evaluation of total artificial lighting of classrooms with different light sources on the basis of the response of the cardiovascular system of schoolchildren].

    Science.gov (United States)

    Teksheva, L M; Zvezdina, I V

    2014-01-01

    Hygienic evaluation of innovative equipment in educational institutions requires the use of appropriate methods permitting to establish valuable criterias for the effectiveness of the application of new technologies. The study of the response of the cardiovascular system of schoolchildren under using different light sources allowed to establish the increase in adaptive capacities and the improvement of the functional state of the organism in LED in comparison with fluorescent lighting.

  15. An implementation of traffic light system using multi-hop Ad hoc networks

    KAUST Repository

    Ansari, Imran Shafique

    2009-08-01

    In ad hoc networks nodes cooperate with each other to form a temporary network without the aid of any centralized administration. No wired base station or infrastructure is supported, and each host communicates via radio packets. Each host must act as a router, since routes are mostly multi-hop, due to the limited power transmission set by government agencies, (e.g. the Federal Communication Commission (FCC), which is 1 Watt in Industrial Scientific and Medical (ISM) band. The natures of wireless mobile ad hoc networks depend on batteries or other fatiguing means for their energy. A limited energy capacity may be the most significant performance constraint. Therefore, radio resource and power management is an important issue of any wireless network. In this paper, a design for traffic light system employing ad hoc networks is proposed. The traffic light system runs automatically based on signals sent through a multi-hop ad hoc network of \\'n\\' number of nodes utilizing the Token Ring protocol, which is efficient for this application from the energy prospective. The experiment consists of a graphical user interface that simulates the traffic lights and laptops (which have wireless network adapters) are used to run the graphical user interface and are responsible for setting up the ad hoc network between them. The traffic light system has been implemented utilizing A Mesh Driver (which allows for more than one wireless device to be connected simultaneously) and Java-based client-server programs. © 2009 IEEE.

  16. Intelligent pulse light source in the performance calibration system of two-dimensional neutron detector

    Science.gov (United States)

    Yang, Lei; Zhao, Xiao-Fang

    2017-07-01

    Chinese Spallation Neutron Source (CSNS) project will use numerous two-dimensional (2D) neutron detectors whose ZnS (Ag) scintillator is doped with 6Li. To ensure the consistency of all neutron detectors, a calibration system for the performance of 2D neutron detectors is designed. For radiation protection, the state control of the radiation source gets more and more strict. It is impossible to directly carry out experiments with massive radioactive particles. Thus, the following scheme has been designed. The controlled pulsed laser light source on a 2D mobile platform is used to replace the neutron bombardment to generate the photon. The pulse signal drives the laser diode to generate pulse light. The pulse light source located on the 2D platform is controlled by the core controller, and goes to the wavelength shift fiber through the optical fiber. The host computer (PC) receives the signal from the electronics system, processes data, and automatically calibrates the performance parameters. As shown by the experimental results, the pulse light source can perfectly meet all requirements of 2D neutron detector calibration system.

  17. The Energy Audit Activity Focused on the Lighting Systems in Historical Buildings

    Directory of Open Access Journals (Sweden)

    Giacomo Salvadori

    2016-11-01

    Full Text Available The energy audit for a building is a procedure designed mainly to obtain adequate knowledge of the energy consumption profile, identify, and quantify opportunities for energy savings by a cost-benefit analysis and report, clearly and comprehensively, about the obtained results. If the audit is referred to a building with a significant historical and artistic value, a compatibility evaluation of the energy saving interventions with the architectural features should also be developed. In this paper, analysing the case study of a historical building used as public offices in Pisa (Italy, the authors describe how it is possible to conduct an energy audit activity (especially dedicated to the lighting system and they show how, for this type of buildings, it is possible to obtain significant energy savings with a refurbishment of the lighting system. A total number of seven interventions on indoor and outdoor lighting sub-systems were analysed in the paper. They are characterised by absolute compatibility with the historical and artistic value of the building and they show short payback times, variable between 4 and 34 months, allowing a reduction of the electrical energy consumption for the artificial indoor and outdoor lighting variable from 1.1 MWh/year to 39.0 MWh/year. The followed methodology and the evaluation results described in the paper, although based on a case study, can be extended to numerous historical buildings used as public offices, a recurring situation in the centres of Italian historical cities.

  18. An Intelligent Energy Saving System for Controlling the Lighting and Ventilation of an Area

    Directory of Open Access Journals (Sweden)

    Kadiri Kamoru. O

    2014-09-01

    Full Text Available Intelligent Energy Saving System is a control system used to control a particular environment in other to optimize the energy. It can be used to control the lighting or air conditioning of an area. An example is the library which can be well illuminated with many lamps. When people are not present at a reading place, the lighting can be made OFF and when they are present, the lighting is made ON by using a sensor to sense the environment condition example temperature, obstacle etc. All these can be done through by Dimming circuit and PIR sensor. The circuit is made in such a way that if a person enters the monitored area, the PIR sensors activate and sense the person, and give to the micro controller. The Infrared energy emitted from the living body is focused by a Fresnel lens segment. Then only the PIR sensor activates when it has sensed the person, LDR checks the light intensity of the monitored area, whether it is bright or dark. Depending on the LDR output, the lamp may be ON / OFF by using Dimmer circuit. This system is also designed to control the air conditioning of the environment by adjusting the speed of fan according to the room temperature measured by thermostat, which is connected to the micro controller. To display the room temperature of PIR mode operation, we are using the LCD display

  19. Distortion free pulse delay system using a pair of tunable white light cavities.

    Science.gov (United States)

    Yum, H N; Kim, M E; Jang, Y J; Shahriar, M S

    2011-03-28

    Recently, a tunable bandwidth white light cavity (WLC) was demonstrated by using an anomalously dispersive intra-cavity medium to adjust a cavity linewidth without reducing the cavity buildup factor [G.S. Pati et al., Phys. Rev. Lett. 99, 133601 (2007)]. In this paper, we show theoretically how such a WLC can be used to realize a distortion-free delay system for a data pulse. The system consists of two WLCs placed in series. Once the pulse has passed through them, the fast-light media in both WLCs are deactivated, so that each of these now acts as a very high reflectivity mirror. The data pulse bounces around between these mirrors, undergoing negligible attenuation per pass. The trapped pulse can be released by activating the fast-light medium in either WLC. Numerical simulations show that such a system can far exceed the delay-bandwidth constraint encountered in a typical data buffer employing slow light. We also show that the pulse remains virtually undistorted during the process.

  20. SPED Light Sheet Microscopy: Fast Mapping of Biological System Structure and Function.

    Science.gov (United States)

    Tomer, Raju; Lovett-Barron, Matthew; Kauvar, Isaac; Andalman, Aaron; Burns, Vanessa M; Sankaran, Sethuraman; Grosenick, Logan; Broxton, Michael; Yang, Samuel; Deisseroth, Karl

    2015-12-17

    The goal of understanding living nervous systems has driven interest in high-speed and large field-of-view volumetric imaging at cellular resolution. Light sheet microscopy approaches have emerged for cellular-resolution functional brain imaging in small organisms such as larval zebrafish, but remain fundamentally limited in speed. Here, we have developed SPED light sheet microscopy, which combines large volumetric field-of-view via an extended depth of field with the optical sectioning of light sheet microscopy, thereby eliminating the need to physically scan detection objectives for volumetric imaging. SPED enables scanning of thousands of volumes-per-second, limited only by camera acquisition rate, through the harnessing of optical mechanisms that normally result in unwanted spherical aberrations. We demonstrate capabilities of SPED microscopy by performing fast sub-cellular resolution imaging of CLARITY mouse brains and cellular-resolution volumetric Ca(2+) imaging of entire zebrafish nervous systems. Together, SPED light sheet methods enable high-speed cellular-resolution volumetric mapping of biological system structure and function.

  1. Reducing Barriers To The Use of High-Efficiency Lighting Systems

    Energy Technology Data Exchange (ETDEWEB)

    Peter Morante

    2005-12-31

    With funding from the U.S. Department of Energy (DOE), the Lighting Research Center (LRC) at Rensselaer Polytechnic Institute completed the four-year research project, Reducing Barriers to the Use of High-Efficiency Lighting Systems. The initial objectives were: (1) identifying barriers to widespread penetration of lighting controls in commercial/industrial (C/I) applications that employ fluorescent lamp technologies, and (2) making recommendations to overcome these barriers. The addition of a fourth year expanded the original project objectives to include an examination of the impact on fluorescent lamps from dimming utilizing different lamp electrode heating and dimming ratios. The scope of the project was narrowed to identify barriers to the penetration of lighting controls into commercial-industrial (C/I) applications that employ fluorescent lamp technologies, and to recommend means for overcoming these barriers. Working with lighting manufacturers, specifiers, and installers, the project identified technological and marketing barriers to the widespread use of lighting controls, specifically automatic-off controls, occupancy sensors, photosensors, dimming systems, communication protocols and load-shedding ballasts. The primary barriers identified include cost effectiveness of lighting controls to the building owner, lack of standard communication protocols to allow different part of the control system to communicate effectively, and installation and commissioning issues. Overcoming the identified barriers requires lighting control products on the market to achieve three main goals: (1) Achieve sufficient functionality to meet the key requirements of their main market. (2) Allow significant cost reduction compared to current market standard systems. Cost should consider: hardware capital cost including wiring, design time required by the specifier and the control system manufacturer, installation time required by the electrician, and commissioning time and

  2. Massive MIMO-OFDM indoor visible light communication system downlink architecture design

    Science.gov (United States)

    Lang, Tian; Li, Zening; Chen, Gang

    2014-10-01

    Multiple-input multiple-output (MIMO) technique is now used in most new broadband communication system, and orthogonal frequency division multiplexing (OFDM) is also utilized within current 4th generation (4G) of mobile telecommunication technology. With MIMO and OFDM combined, visible light communication (VLC) system's diversity gain is increase, yet system capacity for dispersive channels is also enhanced. Moreover, with the emerging massive MIMO-OFDM VLC system, there are significant advantages than smaller systems' such as channel hardening, further increasing of energy efficiency (EE) and spectral efficiency (SE) based on law of large number. This paper addresses one of the major technological challenges, system architecture design, which was solved by semispherical beehive structure (SBS) receiver and so that diversity gain can be identified and applied in Massive MIMO VLC system. Simulation results shows that the proposed design clearly presents a spatial diversity over conventional VLC systems.

  3. Application of the EGM Method to a LED-Based Spotlight: A Constrained Pseudo-Optimization Design Process Based on the Analysis of the Local Entropy Generation Maps

    Directory of Open Access Journals (Sweden)

    Enrico Sciubba

    2011-06-01

    Full Text Available In this paper, the entropy generation minimization (EGM method is applied to an industrial heat transfer problem: the forced convective cooling of a LED-based spotlight. The design specification calls for eighteen diodes arranged on a circular copper plate of 35 mm diameter. Every diode dissipates 3 W and the maximum allowedtemperature of the plate is 80 °C. The cooling relies on the forced convection driven by a jet of air impinging on the plate. An initial complex geometry of plate fins is presented and analyzed with a commercial CFD code that computes the entropy generation rate. A pseudo-optimization process is carried out via a successive series of design modifications based on a careful analysis of the entropy generation maps. One of the advantages of the EGM method is that the rationale behind each step of the design process can be justified on a physical basis. It is found that the best performance is attained when the fins are periodically spaced in the radial direction.

  4. Applications of Optical Sensors to the Detection of Light Scattered from Gelling Systems

    Science.gov (United States)

    Bulone, Donatella; Manno, Mauro; San Biagio, Pier Luigi; Martorana, Vincenzo

    Visible light, scattered within an angle of few degrees, (Small Angle Light Scattering, SALS) yields information on the spatial correlations and dynamical properties on the scale of the micrometers. In this way a quick and non-invasive characterization of a variety of samples is feasible. Lately the SALS instruments have been built around multielement optical sensors (CCD, CMOS), allowing the simultaneous measurement of the complete structure factor even during fast kinetics. An assessment of some sensor matrices of different technology will be presented. The omolecular assemblies produced by polysaccharides or proteins can be functional or dysfunctional, their properties being either desirable or detrimental. Anyhow, their morphology often depends, in a very delicate way, on the presence of cosolutes, on the thermal history, on the biopolymer concentration etc. We present some applications of low angle dynamic and static light scattering to the study of gelling systems (agarose, pectin, insulin).

  5. A personalised and adaptive intelligent system to adjust circadian lighting for elderly housing

    DEFF Research Database (Denmark)

    Flyvholm, Anton; Sen, Sumit; Xylakis, Emmanouil

    2016-01-01

    -door daylight. CaLED lighting seems that may positively influence age-related needs, mood, cognition, alertness, sleep and improve well-being in general [5][6]. To build this intelligent system 3 different types of data are considered and cross-checked: a) medical (biofactors), b) sensor-based (activity...... of immobility. J Gerontol Nurs. Sep;17(9):5–11. [4] Gate 21, Abertslund Kommune, Amager-Hvidovre Hospital, Zumtobel, AAU Copenhagen. (2015) LighTel project. Available from http://www.gate21.dk/project/lightel/ [5] Turner PL, Van Someren EJW, Mainster MA. (2010). The role of environmental light in sleep...... and health: effects of ocular aging and cataract surgery. Sleep Med Rev. Aug;14(4):269–80. [6] Kuijsters, A., Redi, J., de Ruyter, B., & Heynderickx, I. (2015). Lighting to make you feel better: Improving the mood of elderly people with affective ambiences. PloS one, 10(7), e0132732....

  6. Design and Construction of Intelligent Traffic Light Control System Using Fuzzy Logic

    Science.gov (United States)

    Lin, Htin; Aye, Khin Muyar; Tun, Hla Myo; Theingi, Naing, Zaw Min

    2008-10-01

    Vehicular travel is increasing throughout the world, particularly in large urban areas. Therefore the need arises for simulation and optimizing traffic control algorithms to better accommodate this increasing demand. This paper presents a microcontroller simulation of intelligent traffic light controller using fuzzy logic that is used to change the traffic signal cycles adaptively at a two-way intersection. This paper is an attempt to design an intelligent traffic light control systems using microcontrollers such as PIC 16F84A and PIC 16F877A. And then traffic signal can be controlled depending upon the densities of cars behind green and red lights of the two-way intersection by using sensors and detectors circuits.

  7. Dynamics of light, intermediate, heavy and superheavy nuclear systems formed in heavy-ion collisions

    Indian Academy of Sciences (India)

    Manoj K Sharma; Gurvinder Kaur

    2014-05-01

    The dynamical description of light, intermediate, heavy and superheavy nuclei formed in heavy-ion collisions is worked out using the dynamical cluster decay model (DCM), with reference to various effects such as deformation and orientation, temperature, angular momentum etc. Based on the quantum mechanical fragmentation theory (QMFT), DCM has been applied to understand the decay mechanism of a large number of nuclei formed in low-energy heavy-ion reactions. Various features related to the dynamics of competing decay modes of nuclear systems are explored by addressing the experimental data of a number of reactions in light, intermediate, heavy and superheavy mass regions. The DCM, being a non-statistical description for the decay of a compound nucleus, treats light particles (LPs) or equivalently evaporation residues (ERs), intermediate mass fragments (IMFs) and fission fragments on equal footing and hence, provides an alternative to the available statistical model approaches to address fusion–fission and related phenomena.

  8. Route-asymmetrical light transmission of a fiber-chip-fiber optomechanical system

    DEFF Research Database (Denmark)

    Liu, Li; Ding, Yunhong; Cai, Xinlun;

    2016-01-01

    In this paper, we proposed and experimentally demonstrated a route-asymmetrical light transmission scheme based on the thermal radiative effect, which means that forward and backward propagations of an optical device have different transmittances provided they are not present simultaneously......-wave (CW) light but also 10 Gbit/s on-off-keying (OOK) digital signals. Above mentioned unique features can be mostly attributed to the significant characteristics of the thermal radiative effect, which could cause a fiber displacement up to tens of microns. The powerful and significant thermal radiative...... effect opens up a new opportunity and method for route-asymmetrical light transmission. Moreover, this research may have important applications in all-optical systems, such as the optical limiters and ultra-low loss switches....

  9. A precise model of LED lighting and its application in uniform illumination system

    Institute of Scientific and Technical Information of China (English)

    WU Feng-tie; HUANG Qi-lu

    2011-01-01

    Optical models directly effect the irradiance distribution of observed surface.Traditionally,approximate Lambertian models are widely used in designing the light-emitting diodes(LED) arrays in spite of their errors compared with the experimental data.But now a novel LED optical model for uniform illumination system has been proposed,in which the curvefitting technique is used to reduce the inherited errors and modify those previous models.The points from the curve of the LED light intensity are adopted,and a spline curve is designed for fitting,which obtains the revised mode.To verify its feasibility,we apply the new model in a 4 × 4 array design.The results show that compared with the approximate Lambertian,the light intensity distribution produced by the fitting model is more uniform and intense,as is expected.

  10. LED Lighting System Reliability Modeling and Inference via Random Effects Gamma Process and Copula Function

    Directory of Open Access Journals (Sweden)

    Huibing Hao

    2015-01-01

    Full Text Available Light emitting diode (LED lamp has attracted increasing interest in the field of lighting systems due to its low energy and long lifetime. For different functions (i.e., illumination and color, it may have two or more performance characteristics. When the multiple performance characteristics are dependent, it creates a challenging problem to accurately analyze the system reliability. In this paper, we assume that the system has two performance characteristics, and each performance characteristic is governed by a random effects Gamma process where the random effects can capture the unit to unit differences. The dependency of performance characteristics is described by a Frank copula function. Via the copula function, the reliability assessment model is proposed. Considering the model is so complicated and analytically intractable, the Markov chain Monte Carlo (MCMC method is used to estimate the unknown parameters. A numerical example about actual LED lamps data is given to demonstrate the usefulness and validity of the proposed model and method.

  11. The first light of Mini-MegaTORTORA wide-field monitoring system

    CERN Document Server

    Biryukov, A; Karpov, S; Bondar, S; Ivanov, E; Katkova, E; Perkov, A; Sasyuk, V

    2014-01-01

    Here we describe the first light of the novel 9-channel wide-field optical monitoring system with sub-second temporal resolution, Mini-MegaTORTORA, which is being tested now at Special Astrophysical Observatory on Russian Caucasus. The system is able to observe the sky simultaneously in either wide (~900 square degrees) or narrow (~100 square degrees) fields of view, either in clear light or with any combination of color (Johnson B, V or R) polarimetric filters installed, with exposure times ranging from 100 ms to 100 s. The primary goal of the system is the detection of rapid -- with sub-second characteristic time-scales -- optical transients, but it may be also used for studying the variability of the sky objects on longer time scales.

  12. Evaluation of historical museum interior lighting system using fully immersive virtual luminous environment

    Science.gov (United States)

    Navvab, Mojtaba; Bisegna, Fabio; Gugliermetti, Franco

    2013-05-01

    Saint Rocco Museum, a historical building in Venice, Italy is used as a case study to explore the performance of its' lighting system and visible light impact on viewing the large size art works. The transition from threedimensional architectural rendering to the three-dimensional virtual luminance mapping and visualization within a virtual environment is described as an integrated optical method for its application toward preservation of the cultural heritage of the space. Lighting simulation programs represent color as RGB triplets in a devicedependent color space such as ITU-R BT709. Prerequisite for this is a 3D-model which can be created within this computer aided virtual environment. The onsite measured surface luminance, chromaticity and spectral data were used as input to an established real-time indirect illumination and a physically based algorithms to produce the best approximation for RGB to be used as an input to generate the image of the objects. Conversion of RGB to and from spectra has been a major undertaking in order to match the infinite number of spectra to create the same colors that were defined by RGB in the program. The ability to simulate light intensity, candle power and spectral power distributions provide opportunity to examine the impact of color inter-reflections on historical paintings. VR offers an effective technique to quantify the visible light impact on human visual performance under precisely controlled representation of light spectrum that could be experienced in 3D format in a virtual environment as well as historical visual archives. The system can easily be expanded to include other measurements and stimuli.

  13. Optical bistability enabled control of resonant light transmission for an atom-cavity system

    CERN Document Server

    Sawant, Rahul

    2015-01-01

    The control of light transmission through a Fabry-Perot cavity containing atoms is theoretically investigated, when the cavity mode beam and an intersecting control beam are both close to specific atomic resonances. A four-level atomic system is considered and its interaction with the cavity mode is studied by solving for the time dependent cavity field and atomic state populations. The conditions for optical bistability of the atom-cavity system are obtained in steady state limit. For an ensemble of atoms in the cavity mode, the response of the intra-cavity light intensity to the intersecting resonant beam is understood for stationary atoms (closed system) and non-static atoms (open system). The open system is modelled by adjusting the atomic state populations to represent the exchange of atoms in the cavity mode, with the thermal environment. The solutions to the model are used to qualitatively explain the observed steady state and transient behaviour of the light in the cavity mode, in Sharma et. al. [1]. ...

  14. Self-Assembly Strategies for Integrating Light Harvesting and Charge Separation in Artificial Photosynthetic Systems

    Energy Technology Data Exchange (ETDEWEB)

    Wasielewski, Michael R. (NWU)

    2017-02-15

    In natural photosynthesis, organisms optimize solar energy conversion through organized assemblies of photofunctional chromophores and catalysts within proteins that provide specifically tailored environments for chemical reactions. As with their natural counterparts, artificial photosynthetic systems for practical solar fuels production must collect light energy, separate charge, and transport charge to catalytic sites where multielectron redox processes will occur. While encouraging progress has been made on each aspect of this complex problem, researchers have not yet developed self-ordering and self-assembling components and the tailored environments necessary to realize a fully-functional artificial system. Previously researchers have used complex, covalent molecular systems comprised of chromophores, electron donors, and electron acceptors to mimic both the light-harvesting and the charge separation functions of photosynthetic proteins. These systems allow for study of the dependencies of electron transfer rate constants on donor?acceptor distance and orientation, electronic interaction, and the free energy of the reaction. The most useful and informative systems are those in which structural constraints control both the distance and the orientation between the electron donors and acceptors. Self-assembly provides a facile means for organizing large numbers of molecules into supramolecular structures that can bridge length scales from nanometers to macroscopic dimensions. The resulting structures must provide pathways for migration of light excitation energy among antenna chromophores, and from antennas to reaction centers. They also must incorporate charge conduits, that is, molecular 'wires' that can efficiently move electrons and holes between reaction centers and catalytic sites. The central scientific challenge is to develop small, functional building blocks with a minimum number of covalent linkages, which also have the appropriate molecular

  15. Performance of high power LEDs based on Ce:YAG ceramics for automotive application%基于YAG陶瓷封装的大功率车用LED的发光性能

    Institute of Scientific and Technical Information of China (English)

    张晔明; 芶立; 时佳男; 高江东

    2016-01-01

    5 W blue light LED chips based on InGaN were packaged using the Ce:YAG ceramics with different Ce doping levels. The luminescent properties of packaged LED beads were evaluated. Electroluminescence (EL) spectra of the ceramic-packaged LEDs show that Ce:YAG ceramic is a more compact and efficient fluorescent material. More activation centers of Ce3+can be contained in ceramic with a low doping concentration at a small volume. With a concentration of x=0.03 (Cex:Y3-xAl5O12) and a thickness of 0.4 mm, YAG ceramic-packaged LED shows a high luminous efficiency of 88.2 lm/W. The optical performance of this kind of LEDs based on YAG ceramic makes them promising in automotive headlamps.%不同掺杂量的Ce:YAG陶瓷与5 W蓝光芯片封装后得到发光二极管(LED)灯珠并表征了其发光性能。这种陶瓷灯珠的电致发光光谱结果表明,Ce:YAG陶瓷是一种更加紧凑高效的荧光材料,在较低的Ce3+掺杂量和较小体积下可容纳更多的激活中心。采用Ce3+掺杂量为x=0.03(Cex:Y3-xAl5O12),厚度为0.4 mm的YAG陶瓷封装的LED灯珠发光效率可以达到88.2 lm/W,此种陶瓷灯珠在LED车大灯应用领域有很大潜力。

  16. The development and characterization of an exogenous green-light-regulated gene expression system in marine cyanobacteria.

    Science.gov (United States)

    Badary, Amr; Abe, Koichi; Ferri, Stefano; Kojima, Katsuhiro; Sode, Koji

    2015-06-01

    A green-light-regulated gene expression system derived from Synechocystis sp. PCC 6803 was constructed and introduced into the marine cyanobacterial strain Synechococcus sp. NKBG 15041c. The regulation system was evaluated using gfp uv as a reporter gene under red-light illumination and under simultaneous red- and green-light illumination. Expression of the reporter gene was effectively repressed under red-light illumination and increased over 10-fold by illuminating with green light. Control vectors missing either the ccaS sensor histidine kinase gene or the ccaR response regulator gene showed no detectable induction of GFPuv expression. Green-light induction of gfp uv expression was further confirmed by quantitative reverse transcription PCR. The constructed system was effective at regulating the recombinant expression of a target gene using green light in a marine cyanobacterial strain that does not naturally possess such a green-light regulation system. Thus, constructed green-light-regulated gene expression system may be used as a core platform technology for the development of marine cyanobacterial strains in which bioprocesses will be regulated by light.

  17. Development of Dual-light Path Monitoring System of Optical Thin-film Thickness

    Institute of Scientific and Technical Information of China (English)

    XU Shi-jun

    2005-01-01

    The accurate monitoring of optical thin-film thickness is a key technique for depositing optical thin-film. For existing coating equipments, which are low precision and automation level on monitoring thin-film thickness, a new photoelectric control and analysis system has been developed. In the new system, main techniques include a photoelectric system with dual-light path, a dual-lock-phase circuit system and a comprehensive digital processing-control-analysis system.The test results of new system show that the static and dynamic stabilities and the control precision of thin-film thickness are extremely increased. The standard deviation of thin-film thickness, which indicates the duplication of thin-film thickness monitoring, is equal to or less than 0.72%. The display resolution limit on reflectivity is 0.02 %. In the system, the linearity of drift is very high, and the static drift ratio approaches zero.

  18. Live imaging of nervous system development and function using light-sheet microscopy.

    Science.gov (United States)

    Lemon, William C; Keller, Philipp J

    2015-01-01

    In vivo imaging applications typically require carefully balancing conflicting parameters. Often it is necessary to achieve high imaging speed, low photo-bleaching, and photo-toxicity, good three-dimensional resolution, high signal-to-noise ratio, and excellent physical coverage at the same time. Light-sheet microscopy provides good performance in all of these categories, and is thus emerging as a particularly powerful live imaging method for the life sciences. We see an outstanding potential for applying light-sheet microscopy to the study of development and function of the early nervous system in vertebrates and higher invertebrates. Here, we review state-of-the-art approaches to live imaging of early development, and show how the unique capabilities of light-sheet microscopy can further advance our understanding of the development and function of the nervous system. We discuss key considerations in the design of light-sheet microscopy experiments, including sample preparation and fluorescent marker strategies, and provide an outlook for future directions in the field.

  19. Systemic immunoglobulin light-chain amyloidosis presenting hematochezia as the initial symptom.

    Science.gov (United States)

    Kon, Tetsuo; Nakagawa, Naoki; Yoshikawa, Fumitsugu; Haba, Kazunao; Kitagawa, Nagako; Izumi, Michihiro; Kumazaki, Setsuo; Ishida, Satoshi; Aikawa, Ryuichi

    2016-08-01

    Immunoglobulin light-chain (AL) amyloidosis is characterized by the deposition of insoluble fibrils composed of immunoglobulin light chains secreted by monoclonal plasma cells. Given the recent advances in the therapy of AL amyloidosis, it is important to diagnose this disease as early as possible. Herein, we describe the case of a 62-year-old man with hepatitis C virus (HCV)-related cirrhosis presenting with hematochezia. Colonoscopy showed multiple submucosal hematomas within the region ranging from the transverse colon to the sigmoid colon. Kappa immunoglobulin light-chain amyloid deposition was also detected. Bone marrow examination revealed a monoclonal abnormal plasma cell population. Thus, the patient was diagnosed with systemic immunoglobulin light-chain amyloidosis. The hematochezia was conservatively managed. However, because of liver failure caused by liver cirrhosis, the patient developed massive pleural effusion and died of respiratory failure. Postmortem examination revealed amyloid deposition in the esophagus, stomach, duodenum, ileum, descending colon, pancreas, heart, and lung. In these organs, amyloid deposition was limited to the vascular wall. We concluded that AL amyloidosis can present hematochezia arising from submucosal hematoma in the large colon before other systemic symptoms appear.

  20. High security chaotic multiple access scheme for visible light communication systems with advanced encryption standard interleaving

    Science.gov (United States)

    Qiu, Junchao; Zhang, Lin; Li, Diyang; Liu, Xingcheng

    2016-06-01

    Chaotic sequences can be applied to realize multiple user access and improve the system security for a visible light communication (VLC) system. However, since the map patterns of chaotic sequences are usually well known, eavesdroppers can possibly derive the key parameters of chaotic sequences and subsequently retrieve the information. We design an advanced encryption standard (AES) interleaving aided multiple user access scheme to enhance the security of a chaotic code division multiple access-based visible light communication (C-CDMA-VLC) system. We propose to spread the information with chaotic sequences, and then the spread information is interleaved by an AES algorithm and transmitted over VLC channels. Since the computation complexity of performing inverse operations to deinterleave the information is high, the eavesdroppers in a high speed VLC system cannot retrieve the information in real time; thus, the system security will be enhanced. Moreover, we build a mathematical model for the AES-aided VLC system and derive the theoretical information leakage to analyze the system security. The simulations are performed over VLC channels, and the results demonstrate the effectiveness and high security of our presented AES interleaving aided chaotic CDMA-VLC system.

  1. Low emittance pre-injection system for Iranian Light Source Facility

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghipanah, A., E-mail: a.sadeghipanah@ipm.ir [Radiation Applications Department, Shahid Beheshti University, G. C., Tehran (Iran, Islamic Republic of); Feghhi, A.H. [Radiation Applications Department, Shahid Beheshti University, G. C., Tehran (Iran, Islamic Republic of); Rahighi, J. [Iranian Light Source Facility (ILSF), Institute for Research in Fundamental Sciences (IPM), Tehran (Iran, Islamic Republic of); Ghasem, H. [Iranian Light Source Facility (ILSF), Institute for Research in Fundamental Sciences (IPM), Tehran (Iran, Islamic Republic of); School of Particles and Accelerators, Institute for Research in Fundamental Sciences (IPM), Tehran (Iran, Islamic Republic of)

    2016-01-11

    In this paper, we introduce the Iranian Light Source Facility (ILSF) pre-injection system. The optimized parameters of its components, the related beam dynamics issues and the expected performance of the designed system have been described with detail. This paper explains fabrication procedures of some main components and gives the low power microwave measurement results of the constructed RF electron gun. The outcome bunches at the end of the ILSF pre-injection system will have the normalized emittance of 6 mm mrad, length of 1.55 ps and energy spread of 0.06%.

  2. Energy-Saving Automation and LED Lighting Systems in Industry, Transport, Building and Municipal Sector

    Directory of Open Access Journals (Sweden)

    V.P. Klimenko

    2013-09-01

    Full Text Available Protocol of diverse technological data unification providing the ability to scale with a minimal increase in auxiliary information volume that allows its usage, ranging from the simplest microcontrollers to integration of automation equipment in global systems was designed for industrial automation systems. Basic technical solutions implemented in development of LED lighting systems of salon subway cars, including a schematic diagram of the lamp, the main technical characteristics of the lamp power supply, the peculiarities of developed design of LED modules are described.

  3. Information-theoretic analysis of a stimulated-Brillouin-scattering-based slow-light system.

    Science.gov (United States)

    Lee, Myungjun; Zhu, Yunhui; Gauthier, Daniel J; Gehm, Michael E; Neifeld, Mark A

    2011-11-10

    We use an information-theoretic method developed by Neifeld and Lee [J. Opt. Soc. Am. A 25, C31 (2008)] to analyze the performance of a slow-light system. Slow-light is realized in this system via stimulated Brillouin scattering in a 2 km-long, room-temperature, highly nonlinear fiber pumped by a laser whose spectrum is tailored and broadened to 5 GHz. We compute the information throughput (IT), which quantifies the fraction of information transferred from the source to the receiver and the information delay (ID), which quantifies the delay of a data stream at which the information transfer is largest, for a range of experimental parameters. We also measure the eye-opening (EO) and signal-to-noise ratio (SNR) of the transmitted data stream and find that they scale in a similar fashion to the information-theoretic method. Our experimental findings are compared to a model of the slow-light system that accounts for all pertinent noise sources in the system as well as data-pulse distortion due to the filtering effect of the SBS process. The agreement between our observations and the predictions of our model is very good. Furthermore, we compare measurements of the IT for an optimal flattop gain profile and for a Gaussian-shaped gain profile. For a given pump-beam power, we find that the optimal profile gives a 36% larger ID and somewhat higher IT compared to the Gaussian profile. Specifically, the optimal (Gaussian) profile produces a fractional slow-light ID of 0.94 (0.69) and an IT of 0.86 (0.86) at a pump-beam power of 450 mW and a data rate of 2.5 Gbps. Thus, the optimal profile better utilizes the available pump-beam power, which is often a valuable resource in a system design.

  4. Assessment of light touch sensation in the hands of systemic sclerosis patients

    Directory of Open Access Journals (Sweden)

    Paula Gabriel Silva

    2014-09-01

    Full Text Available INTRODUCTION: Systemic sclerosis is a relatively rare connective tissue disorder characterized by severe and progressive fibrosis of the skin. Due to the current lack of available information on this subject, the aim of the present study was to assess light touch sensations in the hands of patients with systemic sclerosis. METHODS: We completed a cross-sectional comparative study. Light touch sensations were evaluated in 30 individuals, including 15 patients with systemic sclerosis who exhibited changes in the dermis of their hands without loss of the distal phalanx and 15 subjects who did not exhibit changes in the upper limbs (control group. The groups were age- and sex-matched. Tactile sensory evaluations were performed using the Semmes-Weinstein monofilament test and the two-point discrimination test. RESULTS: Statistically significant differences were found between groups in the monofilament test. The study group had lower scores across all points of the hand when compared with the control group. Differences were also found when dominant and non-dominant hands were compared (p<0.05. Statistically significant differences were found between groups for a subset of the assessed points in the two-point discrimination test. CONCLUSIONS: The results of a monofilament test showed that tactile sensation, specifically light touch and deep pressure sensations, is altered in the hands of systemic sclerosis patients.

  5. Consequences of respiration in the light on the determination of production in pelagic systems

    Directory of Open Access Journals (Sweden)

    O. Pringault

    2007-01-01

    Full Text Available Oxygen microprobes were used to estimate Community Respiration (R, Net Community Production (NCP and Gross Primary Production (GPP in coastal seawater samples. Using this highly stable and reproducible technique to measure oxygen change during alternating dark and light periods, we show that respiration in the light could account for up to 640% of respiration in the dark. The light enhanced dark respiration can remain elevated for several hours following a 12 h period of illumination. Not including Rlight into calculations of production leads to an underestimation of GPP, which can reach up to 650% in net heterotrophic systems. The production: respiration (P:R ratio is in turn affected by the higher respiration rates and by the underestimation of GPP. While the integration of Rlight into the calculation of P:R ratio does not change the metabolic balance of the system, it decreases the observed tendency, thus net autotrophic systems become less autotrophic and net heterotrophic systems become less heterotrophic. As a consequence, we propose that efforts have to be focused on the estimation and the integration of Rlight into the determination of GPP and R for a better understanding of the aquatic carbon cycle.

  6. Light-Emitting Diodes: Learning New Physics

    Science.gov (United States)

    Planinšic, Gorazd; Etkina, Eugenia

    2015-01-01

    This is the third paper in our Light-Emitting Diodes series. The series aims to create a systematic library of LED-based materials and to provide the readers with the description of experiments and pedagogical treatment that would help their students construct, test, and apply physics concepts and mathematical relations. The first paper, published…

  7. Light-Emitting Diodes: Solving Complex Problems

    Science.gov (United States)

    Planinšic, Gorazd; Etkina, Eugenia

    2015-01-01

    This is the fourth paper in our Light-Emitting Diodes series. The series aims to create a systematic library of LED-based materials and to provide readers with the description of experiments and the pedagogical treatment that would help their students construct, test, and apply physics concepts and mathematical relations. The first paper provided…

  8. Light-Emitting Diodes: Learning New Physics

    Science.gov (United States)

    Planinšic, Gorazd; Etkina, Eugenia

    2015-01-01

    This is the third paper in our Light-Emitting Diodes series. The series aims to create a systematic library of LED-based materials and to provide the readers with the description of experiments and pedagogical treatment that would help their students construct, test, and apply physics concepts and mathematical relations. The first paper, published…

  9. Stress reducing by improvement of vehicle lighting systems; Verbesserung der Fahrzeugbeleuchtung zur Vermeidung von Stress

    Energy Technology Data Exchange (ETDEWEB)

    Westermann, H.; Woerdenweber, B.

    1996-06-01

    Improvements for passive safety of vehicles have been widely accepted. Now, interest is focussing on accident avoidance and enhancement in active safety of vehicles. This includes better information systems and further driving comfort. Centre of attention is the driver, his relation to his immediate surroundings and his behaviour in traffic. Comfort implies absence of stress and relates to awareness and readiness to react. Comfort surves safety. Comfort-system engineering creates the means to raise the drivers welbeing and to maintain his reserves for safe behaviour in traffic. It reduces stress factors, irritations and dangers in traffic. Vision provides over 90 per cent of information for safe driving. International regulations control equipment for vehicle lighting. Vehicle and lights represent an interactive system for information and information-retrieval which should adapt to traffic, road or weather conditions. Today, however, this is not sufficiently the case. In other lighting applications regulations for equipment were replaced by regulations of functions. This permitted lighting systems to adapt to changing visual tasks or conditions, and encompass technological advances and aesthetic demands. This change in regulations has not yet happened in vehicle lighting, but, when it does, will set free reserves in improved visual and driving comfort for active safety. The European research (EUREKA) project AFS and the CELIS project are developments in comfort-system engineering. The CELIS system raises comfort in the vehicle interior for driver and passengers. AFS aims to establish adaptive frontlighting to suit every driving situation. AFS requires a fresh look at regulations. The European AFS project is also a precursor for traffic-ergonomic signal function. (orig.) [Deutsch] Nach breiter Akzeptanz der passiven Sicherheitseinrichtungen richtet sich das Interesse zunehmend auf die Unfallvermeidung durch Massnahmen zur Verbesserung der aktiven Sicherheit. Dazu

  10. An LED-Based, Laboratory-Scale Solar Simulator for Advanced 3, 4, 5 & 6 Junction Space Photovoltaic Power Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — As a result of significant technical effort, the Phase I was successful in delivering a solar simulator prototype that not only proved the initial concept but will...

  11. Development of blood vessel search system using near-infrared light for laparoscopic surgery

    Science.gov (United States)

    Narita, K.; Nakamachi, E.; Morita, Y.; Hagiwara, A.

    2013-09-01

    Our objective of this study is to develop a miniature and high accuracy automatic 3D blood vessel searching system, which will be introduced in the laparoscopic operation with the minimally invasive surgery. Now, the conventional optical system used in the laparoscopic surgery has many difficulties of blood vessel imaging and detection, because the peripheral bio-tissue located around the blood vessel disturbs the light wave propagation, disperses and refracts. Consequently, only unclear image is obtained. We develop a new blood vessel detecting system by using Near-Infrared (NIR) light, two CMOS camera modules and a comprehensive image processing technique, which is implemented in the laparoscope pipe with 25mm in diameter. We adopt the stereo method for the searching system to determine 3D blood vessel location. The blood vessel visualization system adopts hemoglobin's absorption characteristics of the NIR light, which has high permeability for the bio-tissue and absorbency for the hemoglobin. A sharpening process is employed to improve the image quality of original ones, through the LoG filter and the un-sharp-mask processing. 2D location of the blood vessel is calculated from luminance distribution of the image and its depth is calculated by the stereo method. A validity of our blood vessel visualization and 3D detecting system was examined through the comparison with the imaging and detecting the results of organization phantoms, which embedded at known depths under the surface. Experimental results of depth obtained by our detecting system showed good agreements with the given depths, and the availability of this system is confirmed.

  12. Phase and period responses of the circadian system of mice (Mus musculus) to light stimuli of different duration

    NARCIS (Netherlands)

    Comas, M.; Beersma, D. G. M.; Spoelstra, K.; Daan, S.

    2006-01-01

    To understand entrainment of circadian systems to different photoperiods in nature, it is important to know the effects of single light pulses of different durations on the free-running system. The authors studied the phase and period responses of laboratory mice (C57BL6J//OlaHsd) to single light

  13. High immersive three-dimensional tabletop display system with high dense light field reconstruction

    Science.gov (United States)

    Zheng, Mengqing; Yu, Xunbo; Xie, Songlin; Sang, Xinzhu; Yu, Chongxiu

    2014-11-01

    Three-dimensional (3D) tabletop display is a kind of display with wide range of potential applications. An auto-stereoscopic 3D tabletop display system is designed to provide the observers with high level of immersive perception. To improve the freedom of viewing position, the eye tracking system and a set of active partially pixelated masks are utilized. To improve the display quality, large number of images is prepared to generate the stereo pair. The light intensity distribution and crosstalk of parallax images are measured respectively to evaluate the rationality of the auto-stereoscopic system. In the experiment, the high immersive auto-stereoscopic tabletop display system is demonstrated, together with the system architectures including hardware and software. Experimental results illustrate the effectiveness of the high immersive auto-stereoscopic tabletop display system.

  14. Structure light telecentric stereoscopic vision 3D measurement system based on Scheimpflug condition

    Science.gov (United States)

    Mei, Qing; Gao, Jian; Lin, Hui; Chen, Yun; Yunbo, He; Wang, Wei; Zhang, Guanjin; Chen, Xin

    2016-11-01

    We designed a new three-dimensional (3D) measurement system for micro components: a structure light telecentric stereoscopic vision 3D measurement system based on the Scheimpflug condition. This system creatively combines the telecentric imaging model and the Scheimpflug condition on the basis of structure light stereoscopic vision, having benefits of a wide measurement range, high accuracy, fast speed, and low price. The system measurement range is 20 mm×13 mm×6 mm, the lateral resolution is 20 μm, and the practical vertical resolution reaches 2.6 μm, which is close to the theoretical value of 2 μm and well satisfies the 3D measurement needs of micro components such as semiconductor devices, photoelectron elements, and micro-electromechanical systems. In this paper, we first introduce the principle and structure of the system and then present the system calibration and 3D reconstruction. We then present an experiment that was performed for the 3D reconstruction of the surface topography of a wafer, followed by a discussion. Finally, the conclusions are presented.

  15. Multispectral endoscopy and microscopy imaging system using a spectrally programmable light engine

    Science.gov (United States)

    MacKinnon, N.; Stange, Ulrich; Lane, Pierre M.; MacAulay, Calum E.

    2005-03-01

    We report a spectrally and temporally programmable light engine based on a spatial light modulator that can dynamically create any narrow or broadband spectral profile for hyperspectral, fluorescence, or principal component imaging. Most hyperspectral or multispectral imaging systems use wavelength selection devices such as acousto-optic tunable filters (AOTFs), tunable grating or prism-based monochromators, or filter wheels. While these devices can select wavelengths they cannot create arbitrary spectral profiles. This simple and economical system can be controlled at high speed (up to 5000 illumination profiles per second). Digitally controlled illumination is bit additive with image data providing high dynamic range imaging with monochrome or color imaging devices. This is especially advantageous for endoscopes employing small well CCD or CMOS sensors since the dynamic range now can extend beyond the limits of the sensor itself. In this report we show multispectral images of in vivo tissue and in vitro tissue samples using endoscopes, surgical microscopes and conventional microscopes.

  16. Testing, Performance and Reliability Evaluation of Charge Controllers for Solar Photovoltaic Home Lighting System in India

    Directory of Open Access Journals (Sweden)

    Adarsh Kumar

    2016-01-01

    Full Text Available :Charge controller is the most important part of a Solar Photovoltaic Home LightingSystem (SPVHLS which controls the charging ofbattery from photovoltaic (PV module and discharging of battery through load. This paper analyzes testresults of fourteen charge controllers (CC available in Indiaaccording to the Ministry of New and RenewableEnergy (MNRE specification. The different parameters of charge controllers to be tested arebattery high voltage disconnect (HVD, low voltage disconnect(LVD, load reconnect voltage (LRV, short circuit protection etc. It is found thatseven charge controllers meet the technical specifications ofMNRE. There is also a study of different features and properties of the chargecontrollers. Finally a brief discussion on selection appropriate charge controller for Solar Photovoltaic Home LightingSystem (SPVHLS and further improvement ofcharge controller is presented.

  17. Stellar occultation of polarized light from circumstellar electrons. 4: Detached binary systems

    Science.gov (United States)

    Fox, G. K.

    1994-01-01

    The finite sizes of stars in detached binary systems are incorporated in the single scattering approximation of Brown, McLean, & Emslie (1978). In the absence of scatterer occultation, the predicted polarimetric variability is found to be represented by a terminating two harmonic time series, as previously found by Brown et al. (1978). When the occultation of scatterers by the light sources is included, additional Fourier harmonics are introduced. Model results are illustrated for a spherically symmetric scattering envelope centered on the primary star, in which it is found that for occultation effects to be identified in polarimetric data requires the separation of the system to be less than 10 times the radius of the primary, and for the primary to be the dominant light source.

  18. Semiconductor Light-Controlled Instrument Transducer with Direct PWM Output for Automatic Control Systems

    Directory of Open Access Journals (Sweden)

    O. Malik

    2013-02-01

    The internal PWM signal conversion occurs by the use of non-equilibrium physical processes in the semiconductor substrate of the MOS-C. The 10-20 V amplitude limited square PWM output signal is obtained by the amplification of the sensor signal with a standard 60 dB transimpedance amplifier. The amplified output signal presents positive and negative PWM waveforms that can be easily separated using diodes. The duty of the positive part is proportional to the light intensity, whereas the negative part is inversely proportional to the intensity. The frequency operating range of this proposed instrument varies from 1 Hz to a few kilohertz. The duty cycle of the PWM output signal varies from 2% to 98% when the incident light intensity varies in the microwatts range. These new transducers or sensors could be useful for automatic control, robotic applications, dimmer systems, feedback electronic systems, and non-contact optical position sensing for nulling and centering measurements.

  19. Control of light trapping in a large atomic system by a static magnetic field

    CERN Document Server

    Skipetrov, S E; Havey, M D

    2016-01-01

    We propose to control light trapping in a large ensemble of cold atoms by an external, static magnetic field. For an appropriate choice of frequency and polarization of the exciting pulse, the field is expected to speed up the fluorescence of a dilute atomic system but can significantly slow it down in a dense ensemble. The slowing down of fluorescence is due to the excitation of spatially localized collective atomic states that appear only under a strong magnetic field and have exponentially long lifetimes. The control of fluorescence by the magnetic field may be of interest for use in future quantum-information processing devices. It also paves a way towards the experimental observation of the disorder-induced localization of light in cold atomic systems.

  20. Control of light trapping in a large atomic system by a static magnetic field

    Science.gov (United States)

    Skipetrov, S. E.; Sokolov, I. M.; Havey, M. D.

    2016-07-01

    We propose to control light trapping in a large ensemble of cold atoms by an external, static magnetic field. For an appropriate choice of frequency and polarization of the exciting pulse, the field is expected to speed up the fluorescence of a dilute atomic system. In a dense ensemble, the field does not affect the early-time superradiant signal but amplifies intensity oscillations at intermediate times and induces a very slow, nonexponential long-time decay. The slowing down of fluorescence is due to the excitation of spatially localized collective atomic states that appear only under a strong magnetic field and have exponentially long lifetimes. Our results therefore pave a way towards experimental observation of the disorder-induced localization of light in cold atomic systems.