Effect of LED-LCU light irradiance distribution on mechanical properties of resin based materials

Energy Technology Data Exchange (ETDEWEB)

Magalhães Filho, T.R.; Weig, K.M. [Faculdade de Odontologia, Universidade Federal Fluminense, Rua São Paulo 28, CEP 24020-150 Niterói (Brazil); Engenharia Metalúrgica e de Materiais (COPPE), Universidade Federal do Rio de Janeiro, CP 68505, CEP: 21941-972 Rio de Janeiro (Brazil); Costa, M.F. [Engenharia Metalúrgica e de Materiais (COPPE), Universidade Federal do Rio de Janeiro, CP 68505, CEP: 21941-972 Rio de Janeiro (Brazil); Werneck, M.M. [Engenharia Elétrica (COPPE), Universidade Federal do Rio de Janeiro, CP 68504, CEP: 21941-972 Rio de Janeiro (Brazil); Barthem, R.B. [Instituto de Física, Universidade Federal do Rio de Janeiro, CP 68528, CEP: 21941-972 Rio de Janeiro (Brazil); Costa Neto, C.A., E-mail: celio@metalmat.ufrj.br [Engenharia Metalúrgica e de Materiais (COPPE), Universidade Federal do Rio de Janeiro, CP 68505, CEP: 21941-972 Rio de Janeiro (Brazil)

2016-06-01

The objective of this study is to analyze the light power distribution along the tip end of the light guide of three LED-LCUs (Light Curing Units) and to evaluate its effect on the mechanical properties of a polymer based dental composite. Firstly, the light power distribution over the whole area of LED-LCU light guide surface was analyzed by three methods: visual projection observation, spectral measurement and optical spectral analysis (OSA). The light power distribution and the total irradiance were different for the three LEDs used, but the wavelength was within the camphorquinone absorption spectrum. The use of a blank sheet was quite on hand to make a qualitative analysis of a beam, and it is costless. Secondly, specimens of a hybrid composite with approximately 8 mm diameter and 2 mm thickness were produced and polymerized by 20 s exposition time to each LED-LCU. Thirdly, the elastic modulus (E) and hardness (HV) were measured throughout the irradiated area by instrumented micro-indentation test (IIT), allowing to correlate localized power and mechanical properties. Both E and HV showed to be very sensitive to local power and wavelength dependent, but they followed the beam power profile. It was also shown that the mechanical properties could be directly correlated to the curing process. Very steep differences in mechanical properties over very short distances may impair the material performance, since residual stresses can easily be built over it. - Highlights: • A resin based composite (RBC) was polymerized by three different Light Emitting Diodes. • Each LED had its beam profile visually, wavelength and power analyzed. • The effective polymerization power (EPP) varied from 28% to 52% of the total beam power. • Wavelength seems to be as relevant as power in the light curing process. • Mechanical properties depend on the simultaneous effect of wavelength and power.

Spot fat reduction by red and near infrared LED phototherapy

Science.gov (United States)

Lim, Sungkyoo; Park, Eal-Whan

2018-02-01

Low level light therapy (LLLT) using light from red and near infrared LEDs or Lasers have been reported effective as noninvasive methods for reducing spot fat. A total of 55 subjects were randomly divided into test groups and control groups for abdominal fat reduction clinical trial using red and near infrared LED phototherapy devices. Red and near infrared light with irradiance of 10 mW/cm2 were irradiated over the abdominal area to the test group for 30 minutes followed by 30 minutes of aerobic exercise, 3 times a week for 4 weeks. Control group used sham devices for 30 minutes and followed by 30 minutes of aerobic exercise. It is expected that red and near infrared LED phototherapy combined with aerobic exercise would be effective and safe for abdominal fat reduction without any side effects.

Knoop hardness of ten resin composites irradiated with high-power LED and quartz-tungsten-halogen lights.

Science.gov (United States)

Price, Richard B T; Felix, Corey A; Andreou, Pantelis

2005-05-01

This study compared a high-power light-emitting-diode (LED) curing light (FreeLight 2, 3M ESPE) with a quartz-tungsten-halogen (QTH) light (TriLight, 3M ESPE) to determine which was the better at photo-polymerising 10 resin composites. Class I preparations were prepared 4-mm deep into human teeth and filled with 10 different composites. The composites were irradiated for 50% or 100% of their recommended times using the LED light, and for 100% of their recommended times with the QTH light on either the high or medium power setting. Fifteen minutes later, the Knoop hardness of the composites was measured to a depth of 3.5 mm from the surface. When irradiated by the LED light for their recommended curing times, the Knoop hardness of all 10 composites stayed above 80% of the maximum hardness of the composite to a depth of at least 1.5 mm; three composites maintained a Knoop hardness that was more than 80% of their maximum hardness to a depth of 3.5 mm. Repeated measurements analysis of variance indicated that all the two-way and three-way interactions between the curing light, depth, and composite were significant (p hardness values. The LED light, used for the composite manufacturer's recommended time, was ranked the best at curing the composites to a depth of 3mm (p power setting.

LED; Zum Thema LED

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-07-01

This collection of articles on the subject of light emitting diodes (LED) provides technical information on LED technology, examines latest developments and provides examples of LED use in practice. An 'ABC' of LED technology is presented and fifteen common LED mistakes are noted. The chances and risks of LED use are discussed as is the retrofitting of lighting installations with LEDs. The use of LEDs in street lighting is examined. The journal also includes interviews with architects and a lighting designer. Practical examples of the use of LEDs include the refurbished parliamentary library in Berne, their use in the bird sanctuary headquarters in Sempach, Switzerland, as well as LED use in sales outlets. Also, the use of LED lighting in a spa gazebo in Lucerne is examined.

Tailed nuclei and dicentric chromosomes in irradiated subjects

International Nuclear Information System (INIS)

Kravtsov, V.Yu.; Fedortseva, R.F.; Starkova, Ye.V.; Yartseva, N.M.; Nikiforov, A.M.

2000-01-01

A study of peripheral blood smears from irradiated Chernobyl liquidators and other subjects has shown nuclei of some lymphocytes to have a protrusion into the cytoplasm. Such abnormal nuclei are called 'tailed' nuclei (TN). Sixteen main morphologic types, observed in human peripheral blood lymphocytes, are described. The frequency of appearance of lymphocytes with TN in a group of Chernobyl liquidators was significantly higher than in control groups (p<0.001, in all cases). A positive correlation was found between the TN frequency in lymphocytes and dicentric chromosomes in lymphocytes cultured to metaphase (p<0.001). Elevated frequencies of dicentrics, higher than 0.1%, were found in 17 out of 22 subjects in whom the frequency of lymphocytes with TN was 0.8% and more. Abnormalities of the TN type in lymphocytes are likely to result from breakdown of chromosome bridges formed by dicentrics. The TN can be considered as a possible marker of irradiation and, therefore, their detailed study is important

Catalyst-free activation of peroxides under visible LED light irradiation through photoexcitation pathway

Energy Technology Data Exchange (ETDEWEB)

Gao, Yaowen [Department of Environmental Engineering, Wuhan University, Wuhan, 430079 (China); Shenzhen Research Institute of Wuhan University, Shenzhen, 518057 (China); Li, Yixi; Yao, Linyu; Li, Simiao; Liu, Jin [Department of Environmental Engineering, Wuhan University, Wuhan, 430079 (China); Zhang, Hui, E-mail: eeng@whu.edu.cn [Department of Environmental Engineering, Wuhan University, Wuhan, 430079 (China); Shenzhen Research Institute of Wuhan University, Shenzhen, 518057 (China)

2017-05-05

Highlights: • Persulfate could decolorize Rhodamine B (RhB) directly via non-radical reactions. • LED lamps emitting white light were utilized as the visible light source. • Dyes could activate peroxides through photoexcitation pathway. • Decolorization of dyes and production of radicals were achieved simultaneously. • The catalyst-free peroxide/dye/Vis process was effective in a broad pH range. - Abstract: Catalysts are known to activate peroxides to generate active radicals (i.e., hydroxyl radical (·OH) and sulfate radical (SO{sub 4}·{sup −})) under certain conditions, but the activation of peroxides in the absence of catalysts under visible light irradiation has been rarely reported. This work demonstrates a catalyst-free activation of peroxides for the generation of ·OH and/or SO{sub 4}·{sup −} through photoexcited electron transfer from organic dyes to peroxides under visible LED light irradiation, where Rhodamine B (RhB) and Eosin Y (EY) were selected as model dyes. The formation of ·OH and/or SO{sub 4}·{sup −} in the reactions and the electron transfer from the excited dyes to peroxides were validated via electron paramagnetic resonance (EPR), photoluminescence (PL) spectra and cyclic voltammetry (CV). The performance of the peroxide/dye/Vis process was demonstrated to be altered depending on the target substrate. Meanwhile, the peroxide/dye/Vis process was effective for simultaneous decolorization of dyes and production of active radicals under neutral even or basic conditions. The findings of this study clarified a novel photoexcitation pathway for catalyst-free activation of peroxides under visible light irradiation, which could avoid the secondary metal ion (dissolved or leached) pollution from the metal-based catalysts and expand the application range of the peroxide-based catalytic process.

Thermal imaging of high power diode lasers subject to back-irradiance

Science.gov (United States)

Li, C.; Pipe, K. P.; Cao, C.; Thiagarajan, P.; Deri, R. J.; Leisher, P. O.

2018-03-01

CCD-based thermoreflectance imaging and finite element modeling are used to study the two-dimensional (2D) temperature profile of a junction-down broad-area diode laser facet subject to back-irradiance. By determining the temperature rise in the active region (ΔΤAR) at different diode laser optical powers, back-irradiance reflectance levels, and back-irradiance spot locations, we find that ΔΤAR increases by nearly a factor of three when the back-irradiance spot is centered in the absorbing substrate approximately 5 μm away from the active region, a distance roughly equal to half of the back-irradiance spot FWHM (9 μm). This corroborates prior work studying the relationship between the back-irradiance spot location and catastrophic optical damage, suggesting a strong thermal basis for reduced laser lifetime in the presence of back-irradiance for diode lasers fabricated on absorbing substrates.

'In vitro' study of the efficacy of diode laser and LED irradiation during dental bleaching; Estudo 'in vitro' da acao do LED e laser de diodo no clareamento dental

Energy Technology Data Exchange (ETDEWEB)

Barroso, Marcia Cristina da Silva

2003-07-01

This in vitro study evaluated the efficacy of LED and laser diode irradiation during the dental bleaching procedure, using two bleaching agents (Opalescence X-tra and HP Whiteness). The diode laser and the LED were operated in the continuous mode, with wavelength of 808 nm and 470 nm, respectively. The results of the irradiations were characterized with the CIELAB system calculating the L{sup *}a{sup *}b{sup *} values for the darkened and the bleached teeth (60 bovine incisors). This is to our knowledge the first time that light sources laser and LED are compared with respect to their whitening capability when applied to different agents. Significant differences in the chroma value are obtained for the two whitening agents and for the different light sources, too. Also, in terms of luminance, the combination of laser/ Whiteness HP showed significantly better results than when the same agent was used alone or in combination with LED. Best overall results are obtained with the combination of Whiteness HP and laser. (author)

Antimicrobial photodynamic activity and cytocompatibility of Au25(Capt18 clusters photoexcited by blue LED light irradiation

Directory of Open Access Journals (Sweden)

Miyata S

2017-04-01

Full Text Available Saori Miyata,1 Hirofumi Miyaji,1 Hideya Kawasaki,2 Masaki Yamamoto,2 Erika Nishida,1 Hiroko Takita,3 Tsukasa Akasaka,4 Natsumi Ushijima,3 Toshihiko Iwanaga,5 Tsutomu Sugaya1 1Department of Periodontology and Endodontology, Hokkaido University Graduate School of Dental Medicine, Kita-ku, Sapporo, 2Department of Chemistry and Materials Engineering, Faculty of Chemistry, Materials and Bioengineering, Kansai University, Suita-shi, Osaka, 3Support Section for Education and Research, Hokkaido University Graduate School of Dental Medicine, 4Department of Biomedical, Dental Materials and Engineering, Graduate School of Dental Medicine, Hokkaido University, 5Department of Anatomy, Laboratory of Histology and Cytology, Hokkaido University Graduate School of Medicine, Kita-ku, Sapporo, Japan Abstract: Antimicrobial photodynamic therapy (aPDT has beneficial effects in dental treatment. We applied captopril-protected gold (Au25(Capt18 clusters as a novel photosensitizer for aPDT. Photoexcited Au clusters under light irradiation generated singlet oxygen (1O2. Accordingly, the antimicrobial and cytotoxic effects of Au25(Capt18 clusters under dental blue light-emitting diode (LED irradiation were evaluated. 1O2 generation of Au25(Capt18 clusters under blue LED irradiation (420–460 nm was detected by a methotrexate (MTX probe. The antimicrobial effects of photoexcited Au clusters (0, 5, 50, and 500 µg/mL on oral bacterial cells, such as Streptococcus mutans, Aggregatibacter actinomycetemcomitans, and Porphyromonas gingivalis, were assessed by morphological observations and bacterial growth experiments. Cytotoxicity testing of Au clusters and blue LED irradiation was then performed against NIH3T3 and MC3T3-E1 cells. In addition, the biological performance of Au clusters (500 µg/mL was compared to an organic dye photosensitizer, methylene blue (MB; 10 and 100 µg/mL. We confirmed the 1O2 generation ability of Au25(Capt18 clusters through the fluorescence

Bactericidal effect of blue LED light irradiated TiO2/Fe3O4 particles on fish pathogen in seawater

International Nuclear Information System (INIS)

Cheng, T.C.; Yao, K.S.; Yeh, N.; Chang, C.I.; Hsu, H.C.; Gonzalez, F.; Chang, C.Y.

2011-01-01

This study uses blue LED light (λ max = 475 nm) activated TiO 2 /Fe 3 O 4 particles to evaluate the particles' photocatalytic activity efficiency and bactericidal effects in seawater of variable salinities. Different TiO 2 to Fe 3 O 4 mole ratios have been synthesized using sol-gel method. The synthesized particles contain mainly anatase TiO 2 , Fe 3 O 4 and FeTiO 3 . The study has identified TiO 2 /Fe 3 O 4 's bactericidal effect to marine fish pathogen (Photobacterium damselae subsp. piscicida BCRC17065) in seawater. The SEM photo reveals the surface destruction in bacteria incubated with blue LED irradiated TiO 2 /Fe 3 O 4 . The result of this study indicates that 1) TiO 2 /Fe 3 O 4 acquires photocatalytic activities in both the freshwater and the seawater via blue LED irradiation, 2) higher photocatalytic activities appear in solutions of higher TiO 2 /Fe 3 O 4 mole ratio, and 3) photocatalytic activity decreases as salinity increases. These results suggest that the energy saving blue LED light is a feasible light source to activate TiO 2 /Fe 3 O 4 photocatalytic activities in both freshwater and seawater.

The AIR's policy on research involving the irradiation of human subjects

International Nuclear Information System (INIS)

Smith, A.N.

1995-01-01

The policy of the Australian Institute of Radiography with regards to the human subject irradiation is outlined. It is stated that members will not irradiate another individual, nor themselves, solely for the purposes of experimentation or research without gaining the prior approval of an institutional ethics committee. Where possible, researchers should consider the use of patient equivalent or human tissue equivalent phantoms. A short list of references has been compiled to assist members in designing research protocols which comply with the stated policy

Food irradiation and its future prospects

International Nuclear Information System (INIS)

MacQueen, K.F.

1967-01-01

Radiation for food preservation is a way of alleviating problems of food deficiencies in a large part of the world. A review of progress achieved and future prospects was made at the eleventh session of the General Conference in a scientific lecture by Kenneth F. MacQueen, Head of the Food Irradiation Section, Atomic Energy of Canada Ltd. A pioneer in the subject, Mr. MacQueen prepared the petition which led to official acceptance of irradiated potatoes for human consumption in Canada in 1960

LED-based UV source for monitoring spectroradiometer properties

Science.gov (United States)

Sildoja, Meelis-Mait; Nevas, Saulius; Kouremeti, Natalia; Gröbner, Julian; Pape, Sven; Pendsa, Stefan; Sperfeld, Peter; Kemus, Fabian

2018-06-01

A compact and stable UV monitoring source based on state-of-the-art commercially available ultraviolet light emitting diodes (UV-LEDs) has been developed. It is designed to trace the radiometric stability—both responsivity and wavelength scale—of array spectroradiometers measuring direct solar irradiance in the wavelength range between 300 nm and 400 nm. The spectral irradiance stability of the UV-LED-based light source observed in the laboratory after seasoning (burning-in) the individual LEDs was better than 0.3% over a 12 h period of continuous operation. The integral irradiance measurements of the source over a period of several months, where the UV-LED source was not operated continuously between the measurements, showed stability within 0.3%. In-field measurements of the source with an array spectroradiometer indicated the stability of the source to be within the standard uncertainty of the spectroradiometer calibration, which was within 1% to 2%.

Disparity in Cutaneous Pigmentary Response to LED vs Halogen Incandescent Visible Light: Results from a Single Center, Investigational Clinical Trial Determining a Minimal Pigmentary Visible Light Dose.

Science.gov (United States)

Soleymani, Teo; Cohen, David E; Folan, Lorcan M; Okereke, Uchenna R; Elbuluk, Nada; Soter, Nicholas A

2017-11-01

Background: While most of the attention regarding skin pigmentation has focused on the effects of ultraviolet radiation, the cutaneous effects of visible light (400 to 700nm) are rarely reported. The purpose of this study was to investigate the cutaneous pigmentary response to pure visible light irradiation, examine the difference in response to different sources of visible light irradiation, and determine a minimal pigmentary dose of visible light irradiation in melanocompetent subjects with Fitzpatrick skin type III - VI. The study was designed as a single arm, non-blinded, split-side dual intervention study in which subjects underwent visible light irradiation using LED and halogen incandescent light sources delivered at a fluence of 0.14 Watts/cm2 with incremental dose progression from 20 J/cm2 to 320 J/cm2. Pigmentation was assessed by clinical examination, cross-polarized digital photography, and analytic colorimetry. Immediate, dose-responsive pigment darkening was seen with LED light exposure in 80% of subjects, beginning at 60 Joules. No pigmentary changes were seen with halogen incandescent light exposure at any dose in any subject. This study is the first to report a distinct difference in cutaneous pigmentary response to different sources of visible light, and the first to demonstrate cutaneous pigment darkening from visible LED light exposure. Our findings raise the concern that our increasing daily artificial light surroundings may have clandestine effects on skin biology. J Drugs Dermatol. 2017;16(11):1105-1110..

Uniformity of LED light illumination in application to direct imaging lithography

Science.gov (United States)

Huang, Ting-Ming; Chang, Shenq-Tsong; Tsay, Ho-Lin; Hsu, Ming-Ying; Chen, Fong-Zhi

2016-09-01

Direct imaging has widely applied in lithography for a long time because of its simplicity and easy-maintenance. Although this method has limitation of lithography resolution, it is still adopted in industries. Uniformity of UV irradiance for a designed area is an important requirement. While mercury lamps were used as the light source in the early stage, LEDs have drawn a lot of attention for consideration from several aspects. Although LED has better and better performance, arrays of LEDs are required to obtain desired irradiance because of limitation of brightness for a single LED. Several effects are considered that affect the uniformity of UV irradiance such as alignment of optics, temperature of each LED, performance of each LED due to production uniformity, and pointing of LED module. Effects of these factors are considered to study the uniformity of LED Light Illumination. Numerical analysis is performed by assuming a serious of control factors to have a better understanding of each factor.

Correlation of beam electron and LED signal losses under irradiation and long-term recovery of lead tungstate crystals

International Nuclear Information System (INIS)

Batarin, V.A.; Butler, J.; Davidenko, A.M.; Derevschikov, A.A.; Goncharenko, Y.M.; Grishin, V.N.; Kachanov, V.A.; Konstantinov, A.S.; Kravtsov, V.I.; Kubota, Y.; Lukanin, V.S.; Matulenko, Y.A.; Melnick, Y.M.; Meschanin, A.P.; Mikhalin, N.E.; Minaev, N.G.; Mochalov, V.V.; Morozov, D.A.; Nogach, L.V.; Ryazantsev, A.V.; Semenov, P.A.; Semenov, V.K.; Shestermanov, K.E.; Soloviev, L.F.; Stone, S.; Uzunian, A.V.; Vasiliev, A.N.; Yakutin, A.E.; Yarba, J.

2005-01-01

Radiation damage in lead tungstate crystals reduces their transparency. The calibration that relates the amount of light detected in such crystals to incident energy of photons or electrons is of paramount importance to maintaining the energy resolution the detection system. We report on tests of lead tungstate crystals, read out by photomultiplier tubes, exposed to irradiation by monoenergetic electron or pion beams. The beam electrons themselves were used to measure the scintillation light output, and a blue light emitting diode (LED) was used to track variations of crystals transparency. We report on the correlation of the LED measurement with radiation damage by the beams and also show that it can accurately monitor the crystal recovery from such damage

Characterization of polymeric films subjected to lithium ion beam irradiation

Energy Technology Data Exchange (ETDEWEB)

Groenewold, Gary S., E-mail: gary.groenewold@inl.gov [Idaho National Laboratory, 2351 North Boulevard, Idaho Falls, ID 83415-2208 (United States); Cannon, W. Roger; Lessing, Paul A. [Idaho National Laboratory, 2351 North Boulevard, Idaho Falls, ID 83415-2208 (United States); Avci, Recep; Deliorman, Muhammedin; Wolfenden, Mark [Image and Chemical Analysis Laboratory, Montana State University, Bozeman, MT 59717 (United States); Akers, Doug W.; Jewell, J. Keith; Zuck, Larry D. [Idaho National Laboratory, 2351 North Boulevard, Idaho Falls, ID 83415-2208 (United States)

2013-02-01

Highlights: ► Polyethylene glycol (PEG) and paraffinic polymers were subjected to Li ion irradiation. ► Small oligomers detected in irradiated PEG by electrospray ionization (ESI) mass spectrometry. ► Radiolytic scission observed in X-ray photoelectron and electrospray ionization mass spectra. ► Radiation modified paraffinics characterized by changes in non-ionic surfactant additives. ► Results suggest that extent of radiolysis, and radiolytic pathways can be inferred. -- Abstract: Two different polymeric materials that are candidate materials for use as binders for mixed uranium–plutonium oxide nuclear fuel pellets were subjected to Li ion beam irradiation, in order to simulate intense alpha irradiation. The materials (a polyethylene glycol 8000 and a microcrystalline wax) were then analyzed using a combination of mass spectrometry (MS) approaches and X-ray photoelectron spectroscopy (XPS). Samples of the irradiated PEG materials were dissolved in H{sub 2}O and then analyzed using electrospray ionization-MS, which showed the formation of a series of small oligomers in addition to intact large PEG oligomers. The small oligomers were likely formed by radiation-induced homolytic scissions of the C–O and C–C bonds, which furnish radical intermediates that react by radical recombination with H{sup ·} and OH{sup ·}. Surface analysis using SIMS revealed a heterogeneous surface that contained not only PEG-derived polymers, but also hydrocarbon-based entities that are likely surface contaminants. XPS of the irradiated PEG samples indicated the emergence of different carbon species, with peak shifts suggesting the presence of sp{sup 2} carbon atoms. Analysis of the paraffinic film using XPS showed the emergence of oxygen on the surface of the sample, and also a broadening and shifting of the C1s peak, demonstrating a change in the chemistry on the surface. The paraffinic film did not dissolve in either H{sub 2}O or a H{sub 2}O–methanol solution, and

Construction of Tungsten Halogen, Pulsed LED, and Combined Tungsten Halogen-LED Solar Simulators for Solar Cell I-V Characterization and Electrical Parameters Determination

Directory of Open Access Journals (Sweden)

Anon Namin

2012-01-01

Full Text Available I-V characterization of solar cells is generally done under natural sunlight or solar simulators operating in either a continuous mode or a pulse mode. Simulators are classified on three features of irradiance, namely, spectral match with respect to air mass 1.5, spatial uniformity, and temporal stability. Commercial solar simulators use Xenon lamps and halogen lamps, whereas LED-based solar simulators are being developed. In this work, we build and test seven simulators for solar cell characterization, namely, one tungsten halogen simulator, four monochromatic (red, green, blue, and white LED simulators, one multicolor LED simulator, and one tungsten halogen-blue LED simulator. The seven simulators provide testing at nonstandard test condition. High irradiance from simulators is obtained by employing elevated supply voltage to tungsten halogen lamps and high pulsing voltages to LEDs. This new approach leads to higher irradiance not previously obtained from tungsten halogen lamps and LEDs. From I-V curves, electrical parameters of solar cell are made and corrected based on methods recommended in the IEC 60891 Standards. Corrected values obtained from non-STC measurements are in good agreement with those obtained from Class AAA solar simulator.

Effect of irradiation on the potato tubers rotting during storage

International Nuclear Information System (INIS)

Weber, Z.; Fiszer, W.

1991-01-01

The potato tubers subjected to irradiation in autumn were found dry and soft rotting more numerous than non-irradiated ones for the whole period of storage and especially in April and May. The above mentioned phenomenon brought about a little quicker elimination of tubers naturally infected by pectinolytic bacteria. Susceptibility of both kinds of tubers was similar to Fusarium sulphureum introduced under a cover tissue. The irradiation of potato tubers in autumn 1986 led to the appearance of some hard tubers with brown ring spots in spring 1987

Photodynamic therapy using a novel irradiation source, LED lamp, is similarly effective to photodynamic therapy using diode laser or metal-halide lamp on DMBA- and TPA-induced mouse skin papillomas.

Science.gov (United States)

Takahashi, Hidetoshi; Nakajima, Susumu; Ogasawara, Koji; Asano, Ryuji; Nakae, Yoshinori; Sakata, Isao; Iizuka, Hajime

2014-08-01

Photodynamic therapy (PDT) is useful for superficial skin tumors such as actinic keratosis and Bowen disease. Although PDT is non-surgical and easily-performed treatment modality, irradiation apparatus is large and expensive. Using 7, 12-dimethylbenz[a]anthracene (DMBA) and 12-ο-tetradecanoylphorbol-13-acetate (TPA)-induced mouse skin papilloma model, we compared the efficacy of TONS501- and ALA-PDT with a LED lamp, a diode laser lamp or a metal-halide lamp on the skin tumor regression. TONS501-PDT using 660 nm LED lamp showed anti-tumor effect at 1 day following the irradiation and the maximal anti-tumor effect was observed at 3 days following the irradiation. There was no significant difference in the anti-tumor effects among TONS501-PDT using LED, TONS501-PDT using diode laser, and 5-aminolevulinic acid hydrochloride (ALA)-PDT using metal-halide lamp. Potent anti-tumor effect on DMBA- and TPA-induced mouse skin papilloma was observed by TONS501-PDT using 660 nm LED, which might be more useful for clinical applications. © 2014 Japanese Dermatological Association.

A Difference in Cutaneous Pigmentary Response to LED Versus Halogen Incandescent Visible Light: A Case Report from a Single Center, Investigational Clinical Trial Determining a Minimal Pigmentary Visible Light Dose.

Science.gov (United States)

Soleymani, Teo; Soter, Nicholas A; Folan, Lorcan M; Elbuluk, Nada; Okereke, Uchenna R; Cohen, David E

2017-04-01

BACKGROUND: While most of the attention regarding skin pigmentation has focused on the effects on ultraviolet radiation, the cutaneous effects of visible light (400 to 700nm) are rarely reported. In this report, we describe a case of painful erythema and induration that resulted from direct irradiation of UV-naïve skin with visible LED light in a patient with Fitzpatrick type II skin. METHODS AND RESULTS: A 24-year-old healthy woman with Fitzpatrick type II skin presented to our department to participate in a clinical study. As part of the study, the subject underwent visible light irradiation with an LED and halogen incandescent visible light source. After 5 minutes of exposure, the patient complained of appreciable pain at the LED exposed site. Evaluation demonstrated erythema and mild induration. There were no subjective or objective findings at the halogen incandescent irradiated site, which received equivalent fluence (0.55 Watts / cm2). The study was halted as the subject was unable to tolerate the full duration of visible light irradiation. CONCLUSION: This case illustrates the importance of recognizing the effects of visible light on skin. While the vast majority of investigational research has focused on ultraviolet light, the effects of visible light have been largely overlooked and must be taken into consideration, in all Fitzpatrick skin types. J Drugs Dermatol. 2017;16(4):388-392..

Bactericidal effect of blue LED light irradiated TiO{sub 2}/Fe{sub 3}O{sub 4} particles on fish pathogen in seawater

Energy Technology Data Exchange (ETDEWEB)

Cheng, T.C. [Department of Tropical Agriculture and International Cooperation, National Pingtung University of Science and Technology, Taiwan (China); Yao, K.S. [Department of Horticulture, National Taitung Junior College, Taiwan (China); Yeh, N. [Mingdao University, Taiwan (China); Chang, C.I. [Aquaculture Division, Fisheries Research Institute, Council of Agriculture, Taiwan (China); Hsu, H.C. [Department of Life Science, Mingdao University, Taiwan (China); Gonzalez, F. [Department of Tropical Agriculture and International Cooperation, National Pingtung University of Science and Technology, Taiwan (China); Chang, C.Y., E-mail: cyc1136@yahoo.com.tw [Center of General Education, National Taitung Junior College, Taiwan (China)

2011-05-31

This study uses blue LED light ({lambda}{sub max} = 475 nm) activated TiO{sub 2}/Fe{sub 3}O{sub 4} particles to evaluate the particles' photocatalytic activity efficiency and bactericidal effects in seawater of variable salinities. Different TiO{sub 2} to Fe{sub 3}O{sub 4} mole ratios have been synthesized using sol-gel method. The synthesized particles contain mainly anatase TiO{sub 2}, Fe{sub 3}O{sub 4} and FeTiO{sub 3}. The study has identified TiO{sub 2}/Fe{sub 3}O{sub 4}'s bactericidal effect to marine fish pathogen (Photobacterium damselae subsp. piscicida BCRC17065) in seawater. The SEM photo reveals the surface destruction in bacteria incubated with blue LED irradiated TiO{sub 2}/Fe{sub 3}O{sub 4}. The result of this study indicates that 1) TiO{sub 2}/Fe{sub 3}O{sub 4} acquires photocatalytic activities in both the freshwater and the seawater via blue LED irradiation, 2) higher photocatalytic activities appear in solutions of higher TiO{sub 2}/Fe{sub 3}O{sub 4} mole ratio, and 3) photocatalytic activity decreases as salinity increases. These results suggest that the energy saving blue LED light is a feasible light source to activate TiO{sub 2}/Fe{sub 3}O{sub 4} photocatalytic activities in both freshwater and seawater.

Software Design of SMD LEDs for Homogeneous Distribution of Irradiation in the Model of Dark Room

Directory of Open Access Journals (Sweden)

Andrej Liner

2014-01-01

Full Text Available This article describes wireless optical data networks using visible spectra of optical radiation with a focus on interior areas with direct line of sight LOS (line-of-sight. This type of network represents progressively evolving area of information technologies. Development of lightning technologies based on white power LED was the impulse for wireless optical data networks based on visible spectra of optical radiation (VLC development. Its basic advantage is the flexibility of users. Users don’t have to stay on one place during the data sharing anymore. Wireless optical data networks represent an alternative solution for metallic and fiber networks [1], [2]. This paper deals with the software simulation of homogeneous distribution of optical irradiation in dark room model, carrying out in LightTools software. First, in previous simulations, the optical source composed from 9 SMD LED’s type LW G6SP-EAFA-JKQL-1 was designed. In various simulations, various numbers and distributions of LED’s were used. These were placed at the ceiling of the dark room. At last, the results of optical irradiation homogeneity are compared.

Raman ratios on the repair of grafted surgical bone defects irradiated or not with laser (λ780 nm) or LED (λ850 nm).

Science.gov (United States)

Pinheiro, Antonio Luiz B; Soares, Luiz Guilherme P; Marques, Aparecida Maria C; Aciole, Jouber Mateus S; de Souza, Renato Aparecido; Silveira, Landulfo

2014-09-05

This work aimed to assess biochemical changes associated to mineralization and remodeling of bone defects filled with Hydroxyapatite+Beta-Beta-tricalcium phosphate irradiated or not with 2 light sources. Ratios of intensities, band position and bandwidth of selected Raman peaks of collagen and apatites were used. Sixty male Wistar rats were divided into 6 groups subdivided into 2 subgroups (15th and 30th days). A standard surgical defect was created on one femur of each animal. In 3 groups the defects were filled with blood clot (Clot, Clot+Laser and Clot+LED groups) and in the remaining 3 groups the defects were filled with biomaterial (Biomaterial, Biomaterial+Laser and Biomaterial+LED groups). When indicated, the defects were irradiated with either Laser (λ780 nm, 70 mW, Φ∼0.4 cm(2)) or LED (λ850±10 nm, 150 mW, Φ∼0.5 cm(2)), 20 J/cm(2) each session, at 48 h intervals/2 weeks (140 J/cm(2) treatment). Following sacrifice, bone fragments were analyzed by Raman spectroscopy. Statistical analysis (ANOVA General Linear Model, pRaman ratios of selected protein matrix and phosphate and carbonate HA indicated that the use of biphasic synthetic micro-granular HA+Beta-TCP graft improved the repair of bone defects, associated or not with Laser or LED light, because of the increasing deposition of HA. Copyright © 2014 Elsevier B.V. All rights reserved.

Detection of increased frequency of thyroid hypoplasia in subjects irradiated in utero as the results of Chernobyl catastrophe

Energy Technology Data Exchange (ETDEWEB)

Drozd, V.; Danilova, L.; Lushchyk, M.; Leonova, T.; Platonova, T. [International Fund Arnica, Minsk (Belarus); Grigorovich, A.; Sivuda, V. [Brest Regional Endocrinological Dispensary, Brest (Belarus); Branovan, I. [Chernobyl Project, New-York (United States); Biko, I.; Reiners, C. [Clinic and Policlinic of Nuclear Medicine, University of Wurzburg, Wursburg (Germany)

2012-07-01

For the 24 years passed after the Chernobyl catastrophe a significant experience in estimation of medical consequences of thyroid irradiation among Belarus patients had been accumulated. The aim of our screening of ultrasonic examination was the detection of the thyroid hypoplasia prevalence in the regions affected with radionuclide fallout. Since 2004 to 2007 thyroid ultrasound with volume estimation was performed in 3311 Belarus subjects, living on the areas of Brest region with the different contamination rate density. Examined subjects were divided in 3 groups: 1) irradiated at the age of 1 to 3 years old at the moment of Chernobyl catastrophe, 2) irradiated in utero, and 3) born after the catastrophe. It was revealed that thyroid hypoplasia was detected in 3% of group 1 (out of 1876 persons), in 5, 8% of group 2 (out of 503 persons, P<0.05) and in 1, 7% of the third group (out of 932 persons). The separation of the irradiated in utero subjects (group 2) to subgroups in dependence of the gestation period, showed the highest prevalence of thyroid hypoplasia among the irradiated in the first trimester of gestation: 7, 7% (P<0.05), in the second trimester: 5, 3%, in the third trimester: 4, 7%

Detection of increased frequency of thyroid hypoplasia in subjects irradiated in utero as the results of Chernobyl catastrophe

International Nuclear Information System (INIS)

Drozd, V.; Danilova, L.; Lushchyk, M.; Leonova, T.; Platonova, T.; Grigorovich, A.; Sivuda, V.; Branovan, I.; Biko, I.; Reiners, C.

2012-01-01

For the 24 years passed after the Chernobyl catastrophe a significant experience in estimation of medical consequences of thyroid irradiation among Belarus patients had been accumulated. The aim of our screening of ultrasonic examination was the detection of the thyroid hypoplasia prevalence in the regions affected with radionuclide fallout. Since 2004 to 2007 thyroid ultrasound with volume estimation was performed in 3311 Belarus subjects, living on the areas of Brest region with the different contamination rate density. Examined subjects were divided in 3 groups: 1) irradiated at the age of 1 to 3 years old at the moment of Chernobyl catastrophe, 2) irradiated in utero, and 3) born after the catastrophe. It was revealed that thyroid hypoplasia was detected in 3% of group 1 (out of 1876 persons), in 5, 8% of group 2 (out of 503 persons, P<0.05) and in 1, 7% of the third group (out of 932 persons). The separation of the irradiated in utero subjects (group 2) to subgroups in dependence of the gestation period, showed the highest prevalence of thyroid hypoplasia among the irradiated in the first trimester of gestation: 7, 7% (P<0.05), in the second trimester: 5, 3%, in the third trimester: 4, 7%

Effect of irradiation on the prevulcanized latex/low nitrosamines latex blends

Energy Technology Data Exchange (ETDEWEB)

Ibrahim, Pairu; Zin, Wan Manshol Wan [Malaysian Nuclear Agency, 43000 kajang, Selangor (Malaysia); Daik, Rusli [Faculty of Science and Technology, Universiti Kebangsaan Malaysia,43600 bangi, Selangor (Malaysia)

2015-09-25

Radiation Prevulcanized Natural Rubber Latex (RVNRL) was blended with Low Nitrosamines Latex (LNL) at different composition ratio. Methyl Metachrylate (MMA) was added for grafting onto the blended latex. Blended latex was subjected to gamma irradiation at various doses up to 8kGy. The mechanical properties and FTIR analysis were investigated as a function of the blended composition and irradiation dose. It was found that blending at specific ratio and gamma irradiation at specific dose led to significant improvement on the properties of the latex. The optimum mechanical properties was attained at a total blending ratio of 70% RVNRL and 30% of LNL.

Thermoluminescent response of aluminium oxide thin films subject to gamma irradiation

Energy Technology Data Exchange (ETDEWEB)

Arrieta, A.; Escobar A, L.; Camps, E.; Villagran, E.; Gonzalez, P.R

2006-07-01

The thermoluminescent (TL) properties of amorphous aluminium oxide thin films (thicknesses as low as 0.3 {mu}m) subjected to gamma (Co-60) irradiation are reported. Aluminium oxide thin films were prepared by laser ablation from an Al{sub 2}O{sub 3} target using a Nd: YAG laser with emission at the fundamental line. The films were exposed to gamma radiation (Co-60) in order to study their TL response. Thermoluminescence glow curves exhibited two peaks at 110 and 176 C. The high temperature peak shows good stability and 30% fading in the first 5 days after irradiation. A linear relationship between absorbed dose and the thermoluminescent response for doses span from 150 mGy to 100 Gy was observed. These results suggest that aluminium oxide thin films are suitable for detection and monitoring of gamma radiation. (Author)

UV-LEDs Efficiently Inactivate DNA and RNA Coliphages

Directory of Open Access Journals (Sweden)

Alyaa M. Zyara

2017-01-01

Full Text Available UV-LEDs are a new method of disinfecting drinking water. Some viruses are very resistant to UV and the efficiency of UV-LEDs to disinfect them needs to be studied. Drinking water was disinfected with UV-LEDs after spiking the water with MS2 and four UV- and/or Cl-resistant coliphages belonging to RNA or DNA coliphages isolated from municipal wastewater. UV-LEDs operating at a wavelength of 270 nm for 2 min with 120 mW of irradiation caused 0.93–2.73 Log10-reductions of coliphages tested in a reactor of a 5.2 L volume. Irradiation time of 10 min in the same system increased the Log10-reductions to 4.30–5.16. Traditional mercury UV (Hg-UV lamp at a 254 nm wavelength caused 0.67–4.08 Log10-reductions in 2 min and 4.56–7.21 Log10-reductions in 10 min in 10 mL of water. All coliphages tested except MS2 achieved 4 Log10-reductions with UV-LEDs at a dose that corresponded to 70 mWs/cm2 using Hg-UV. Thus, UV-LEDs are a promising method of disinfecting UV- and/or Cl-resistant viruses.

LED and Semiconductor Photo-effects on Living Things

Science.gov (United States)

Fujiyasu, Hiroshi; Ishigaki, Takemitsu; Fujiyasu, Kentarou; Ujihara, Shirou; Watanabe, Naoharu; Sunayama, Shunji; Ikoma, Shuuji

We have studied LED irradiation effects on plants and animals in the visible to UV region of light from GaN LEDs. The results are as follows. Blue light considers to be effective for pearl cultivation or for attraction of small fishes living in near the surface of sea such as Pompano or Sardine, white light radiation is effective for cultivation of botanical plankton for shells. Other experiments of UV light irradiation attracting effect on baby sea turtle and the germination UV effect of mushroom, green light weight enhance effect on baby pigs, light vernalization effect of vegitable and Ge far infrared therapic effect on human body are also given.

Detection of irradiated spices by different physical techniques

International Nuclear Information System (INIS)

Chabane, S.; Pouliquen-Sonaglia, I.; Raffi, J.

2001-01-01

We used thermoluminescence, electron spin resonance, and viscosimetric measurements to establish whether or not a spice had been irradiated. Thermoluminescence, using the 1788 EN official protocol with an alternative method for the extraction of mineral impurities, led to proof of irradiation or proof of no treatment. Electron spin resonance led to different spectrum shapes depending on the chemical composition of the spices; ESR could only be used as proof of irradiation up to several weeks after irradiation, and only for some spices. Viscosimetric measurements carried out on spice suspensions led to a presumption of treatment (or of no treatment) and possibly to of of irradiation. (author)

Microwave irradiation enhances kinetics of the biomimetic process of hydroxyapatite nanocomposites

International Nuclear Information System (INIS)

Guha, Avijit; Nayar, Suprabha; Thatoi, H N

2010-01-01

In situ synthesized hydroxyapatite-poly(vinyl) alcohol nanocomposite was subjected to microwave irradiation, post synthesis. Interestingly, the aging time of 1 week required for the normal biomimetic process was reduced to 1 h post microwave irradiation, as characterized by x-ray powder diffraction and transmission electron microscopy. The surface topography shows the tendency of tubules to cross-link with the help of microwave energy. The microwave energy seems to provide a directional pull to the polymer chains which could have led to an enhancement of the kinetics of phase formation. (communication)

Development of a new water sterilization device with a 365 nm UV-LED.

Science.gov (United States)

Mori, Mirei; Hamamoto, Akiko; Takahashi, Akira; Nakano, Masayuki; Wakikawa, Noriko; Tachibana, Satoko; Ikehara, Toshitaka; Nakaya, Yutaka; Akutagawa, Masatake; Kinouchi, Yohsuke

2007-12-01

Ultraviolet (UV) irradiation is an effective disinfection method. In sterilization equipment, a low-pressure mercury lamp emitting an effective germicidal UVC (254 nm) is used as the light source. However, the lamp, which contains mercury, must be disposed of at the end of its lifetime or following damage due to physical shock or vibration. We investigated the suitability of an ultraviolet light-emitting diode at an output wavelength of 365 nm (UVA-LED) as a sterilization device, comparing with the other wavelength irradiation such as 254 nm (a low-pressure mercury lam) and 405 nm (LED). We used a commercially available UVA-LED that emitted light at the shortest wavelength and at the highest output energy. The new sterilization system using the UVA-LED was able to inactivate bacteria, such as Escherichia coli DH5 alpha, Enteropathogenic E. coli, Vibrio parahaemolyticus, Staphylococcus aureus, and Salmonella enterica serovar Enteritidis. The inactivations of the bacteria were dependent on the accumulation of UVA irradiation. Taking advantage of the safety and compact size of LED devices, we expect that the UVA-LED sterilization device can be developed as a new type of water sterilization device.

Strand breaks and lethal damage in plasmid DNA subjected to 60CO-γirradiation

International Nuclear Information System (INIS)

Klimczak, U.

1992-01-01

Experiments with calf thymus DNA subjected to extracellular irradiation yield information on the role of direct and indirect effects in single-strand breakage, if this is evaluated with reference to the scavenger activity in respect of OH radicals. The role of the two processes in the occurrence of double-stand breaks and further damage leading to cell decay has so far remained largely obscure. It was the aim of the study described here to contribute to research in this field by performing in vitro experiments on biologically active DNA. For this purpose, DNA from pBR322 plasmids was irradiated in the presence of OH-radical scavengers. The number of single-strand and double-strand breaks was determined on the basis of the system's ability to eliminate OH radicals. In order to asses the influence of irradiation processes on the biological activity of DNA, investigations were carried out in E. coli for transformations caused by irradiated plasmid DNA. The results were interpreted in the light of theories about inhomogenous reaction kinetics put forward by Mark et al. (1989). It was finally discussed, which of the gamma-irradiation injuries occurring in DNA was to be held responsible for the inactivation of plasmid DNA and which enzymatic processes were additionally at work here. (orig./MG) [de

Experimental investigation on variation of physical properties of coal samples subjected to microwave irradiation

Science.gov (United States)

Hu, Guozhong; Yang, Nan; Xu, Guang; Xu, Jialin

2018-03-01

The gas drainage rate of low-permeability coal seam is generally less than satisfactory. This leads to the gas disaster of coal mine, and largely restricts the extraction of coalbed methane (CBM), and increases the emission of greenhouse gases in the mining area. Consequently, enhancing the gas drainage rate is an urgent challenge. To solve this problem, a new approach of using microwave irradiation (MWR) as a non-contact physical field excitation method to enhance gas drainage has been attempted. In order to evaluate the feasibility of this method, the methane adsorption, diffusion and penetrability of coal subjected to MWR were experimentally investigated. The variation of methane adsorbed amount, methane diffusion speed and absorption loop for the coal sample before and after MWR were obtained. The findings show that the MWR can change the adsorption property and reduce the methane adsorption capacity of coal. Moreover, the methane diffusion characteristic curves for both the irradiated coal samples and theoriginal coal samples present the same trend. The irradiated coal samples have better methane diffusion ability than the original ones. As the adsorbed methane decreases, the methane diffusion speed increases or remain the same for the sample subjected to MWR. Furthermore, compared to the original coal samples, the area of the absorption loop for irradiated samples increases, especially for the micro-pore and medium-pore stage. This leads to the increase of open pores in the coal, thus improving the gas penetrability of coal. This study provides supports for positive MWR effects on changing the methane adsorption and improving the methane diffusion and the gas penetrability properties of coal samples.

LED phototherapy on midpalatal suture after rapid maxilla expansion: a Raman spectroscopic study

Science.gov (United States)

Rosa, Cristiane B.; Habib, Fernando Antonio L.; de Araújo, Telma M.; dos Santos, Jean N.; Cangussu, Maria Cristina T.; Barbosa, Artur Felipe S.; de Castro, Isabele Cardoso V.; Soares, Luiz Guilherme P.; Pinheiro, Antonio L. B.

2015-03-01

A quick bone formation after maxillary expansion would reduce treatment timeand the biomodulating effects of LED light could contribute for it. The aim of this study was to analyze the effect of LED phototherapy on the acceleration of bone formation at the midpalatal suture after maxilla expansion. Thirty rats divided into 6 groups were used on the study at 2 time points - 7 days: Control; Expansion; and Expansion + LED; and 14 days: Expansion; Expansion + LED in the first week; Expansion and LED in the first and second weeks. LED irradiation occurred at every 48 h during 2 weeks. Expansion was accomplished using a spatula and maintained with a triple helicoid of 0.020" stainless steel orthodontic wire. A LED light (λ850 ± 10nm, 150mW ± 10mW, spot of 0.5cm2, t=120 sec, SAEF of 18J/cm2) was applied in one point in the midpalatal suture immediately behind the upper incisors. Near infrared Raman spectroscopic analysis of the suture region was carried and data submitted to statistical analyzes (p≤0.05). Raman spectrum analysis demonstrated that irradiation increased hydroxyapatite in the midpalatal suture after expansion. The results of this indicate that LED irradiation; have a positive biomodulation contributing to the acceleration of bone formation in the midpalatal suture after expansion procedure.

Low-intensity LED therapy (658 nm) on burn healing: a series of cases.

Science.gov (United States)

de Oliveira, Rauirys Alencar; Boson, Luara Lis Barbosa; Portela, Seísa Marina Martins; Filho, Antônio Luiz Martins Maia; de Oliveira Santiago, Denyberg

2018-05-01

The objective of this study was to evaluate the effects of LED on burns healing. Five patients with skin burns were submitted to photobiomodulation by LED, GaAsIP diode, (λ 658 nm) with 40 mW, 7 J/cm 2 on every other day. Biopsies of burned skin were performed and the healing process was photographed. Patients with bilateral burns were used as self-control, having one limb being irradiated and the contralateral limb irradiated with placebo. The burns treated with LED showed higher epithelization, with keratinocytes and fibroblasts proliferation, increased collagen synthesis, decreased pain, and pruritus. In conclusion, there was a faster clinical improvement in the irradiated limbs.

Using LEDs to stimulate the recovery of radiation damage to plastic scintillators

Energy Technology Data Exchange (ETDEWEB)

Wetzel, J., E-mail: james-wetzel@uiowa.edu [The University of Iowa, Iowa City, IA (United States); Tiras, E. [The University of Iowa, Iowa City, IA (United States); Bilki, B. [The University of Iowa, Iowa City, IA (United States); Beykent University, Istanbul (Turkey); Onel, Y. [The University of Iowa, Iowa City, IA (United States); Winn, D. [Fairfield University, Fairfield, CT (United States)

2017-03-15

In this study, we consider using LEDs to stimulate the recovery of scintillators damaged from radiation in high radiation environments. We irradiated scintillating tiles of polyethylene naphthalate (PEN), Eljen brand EJ-260 (EJN), an overdoped EJ-260 (EJ2P), and a lab-produced elastomer scintillator (ES) composed of p-terphenyl (ptp) in epoxy. Two different high-dose irradiations took place, with PEN dosed to 100 kGy, and the others to 78 kGy. We found that the ‘blue’ scintillators (PEN and ES) recovered faster and maximally higher with LEDs than without. Conversely exposing the ‘green’ scintillators (EJ-260) to LED light had a nearly negligible effect on the recovery. We hypothesize that the ‘green’ scintillators require wavelengths that match their absorption and emission spectra for LED stimulated recovery.

Computer codes for simulating atomic-displacement cascades in solids subject to irradiation

International Nuclear Information System (INIS)

Asaoka, Takumi; Taji, Yukichi; Tsutsui, Tsuneo; Nakagawa, Masayuki; Nishida, Takahiko

1979-03-01

In order to study atomic displacement cascades originating from primary knock-on atoms in solids subject to incident radiation, the simulation code CASCADE/CLUSTER is adapted for use on FACOM/230-75 computer system. In addition, the code is modified so as to plot the defect patterns in crystalline solids. As other simulation code of the cascade process, MARLOWE is also available for use on the FACOM system. To deal with the thermal annealing of point defects produced in the cascade process, the code DAIQUIRI developed originally for body-centered cubic crystals is modified to be applicable also for face-centered cubic lattices. By combining CASCADE/CLUSTER and DAIQUIRI, we then prepared a computer code system CASCSRB to deal with heavy irradiation or saturation damage state of solids at normal temperature. Furthermore, a code system for the simulation of heavy irradiations CASCMARL is available, in which MARLOWE code is substituted for CASCADE in the CASCSRB system. (author)

Modification of ethylene-norbornene copolymer by Gamma irradiation

Directory of Open Access Journals (Sweden)

Kačarević-Popović Zorica M.

2006-01-01

Full Text Available The possibility of modifying polyethylene and many other polymers with high energy radiation has led to many useful applications. Due to their new combination of properties and the shortage of experimental data, the radiolysis of a new class of materials, cyclo-olefin copolymers (COC, polymerised from norbornene and ethylene using metallocene catalysts, is of great interest to the study of radiation chemistry and the physics of polymeric systems. Ethylenenorbornene copolymer, pristine and containing an antioxidant were subjected to gamma irradiation in the presence of air and in water. The irradiated copolymer was studied using IR and UV-vis spectrophotometric analysis. The radiation-induced changes in the molecular structure were correlated to changes in the glass transition temperature measured by the DSC method.

Present status and subjects of food irradiation in the world

International Nuclear Information System (INIS)

Hayashi, Toru

1995-01-01

Food irradiation is the technology of irradiating such radiations as gamma ray and electron beam to foods and farm products, and its objectives are the prevention of germination of potatoes and onions, the insecticide of cereals and fruits, the adjustment of the ripeness of fruits and vegetables, the sterilization of chickens and spices and so on. The food irradiation as the technology for preventing the loss of foods, the food irradiation as the substitute for the fumigation with chemicals and the food irradiation for improving food sanitation are discussed. The history of the soundness test of irradiated foods and the opinion of the international organizations are described. The safety evaluation in view of poisonous effect, nutrition and microorganisms is carried out, and the safety of the foods irradiated with the dose less than 10 kGy has been proved. The examples of utilizing food irradiation for sterilization, insecticide and germination prevention are shown. The present status of its practical use in America and Europe and the move of such international organizations as IAEA, FAO and WHO are reported. (K.I.)

LED-pumped Alexandrite laser oscillator and amplifier

Science.gov (United States)

Pichon, Pierre; Blanchot, Jean-Philippe; Balembois, François; Druon, Frédéric; Georges, Patrick

2018-02-01

In this paper, we report the first LED-pumped transition-metal-doped laser oscillator and amplifier based on an alexandrite crystal (Cr3+:BeAl2O4). A Ce:YAG luminescent concentrator illuminated by blue LEDs is used to reach higher pump powers than with LEDs alone. The luminescent 200-mm-long-composit luminescent concentrator involving 2240 LEDs can delivers up to 268 mJ for a peak irradiance of 8.5 kW/cm2. In oscillator configuration, an LED-pumped alexandrite laser delivering an energy of 2.9 mJ at 748 nm in free running operation is demonstrated. In the cavity, we measured a double pass small signal gain of 1.28, in good agreement with numerical simulations. As amplifier, the system demonstrated to boost a CW Ti:sapphire laser by a factor of 4 at 750 nm in 8 passes with a large tuning range from 710 nm to 800 nm.

The effect of electron beam irradiation on forensic evidence. 1. Latent print recovery on porous and non-porous surfaces.

Science.gov (United States)

Ramotowski, Robert S; Regen, Erin M

2005-03-01

The recent use of the postal system as a means of delivering anthrax spores via several contaminated envelopes has led to the selective irradiation of mail. These as yet unsolved attacks and the U.S. Postal Service's decision to irradiate certain types of mail has led to some unexpected complications. The high doses of radiation required to destroy biological agents like anthrax are sufficient to induce damage to other materials present in the envelope. There have been reports of damage to many different items that have been subjected to irradiation, including paper, precious gems, plastic, computer discs, and electronics. However, few studies have examined the effect of such treatments on items of forensic interest. In this paper, the authors focused on the impact of the irradiation process on the ability to visualize latent prints. This experiment involved using several donors, substrates (both porous and non-porous), and visualization reagents. The results indicate that the irradiation process can have a detrimental effect on the success of certain visualization reagents.

Development of efficient, radiation-insensitive GaAs:Zn LEDs

International Nuclear Information System (INIS)

Barnes, C.E.

1977-01-01

Although amphoterically Si doped GaAs LEDs are commercially popular because of their high light output, they are extremely sensitive to irradiation. Therefore, it would be desirable to have a viable alternative available for radiation environment applications. In this work it is shown that by increasing the hole concentration in the active region of nonamphoterically doped GaAs LEDs, one can simultaneously achieve high light output and low radiation sensitivity. Experimental results indicate that the minority carrier lifetime is smaller in more heavily doped devices so that the lifetime-damage constant, tau/sub o/K, is also smaller. Hence, the heavily doped devices should have greater radiation hardness. Neutron-induced light output degradation data as a function of hole concentration confirm this conclusion. The results also show that the pre-irradiation light output is greatest in the heavily doped LEDs. The accompanying decrease of tau/sub o/ in the heavily doped devices indicates that the total minority carrier lifetime is at least partially controlled by the radiative lifetime; a requirement for simultaneously achieving radiation hardness and high initial light output. Finally, an experimental comparison with amphoterically Si doped LEDs shows that the heavily doped devices are superior for neutron fluences greater than 2 x 10 12 n/cm 2

Construction of an array of LEDs coupled to a concentrator for phototherapy

Science.gov (United States)

Almeida, Joana; Liang, Dawei

2011-07-01

The use of LED devices for phototherapy has been expanding in the last decade. This technology provides a safer emission spectrum in large target tissue areas when compared to laser emissions. For enhancing the phototherapeutic effects of red light emitted by LEDs, a simple optical concentrator capable of efficient light concentration and homogenization was developed. The LEDs wavelength of 660 nm is coincident with an absorption peak of the mitochondrial photoreceptor molecule cytochrome c oxidase. The prototype was optimized by non-sequential ray-tracing software ZEMAX, attaining both excellent light uniformity and 50mW/cm2 irradiance at the concentrator output end. Heat emanated from the LEDs source is effectively dissipated by the side walls of the concentrator, ensuring a nearly constant temperature environment for tissue treatment. The prototype was tested on cutaneous hyperpigmented marks caused by cupping in two healthy volunteers. Marks were irradiated by LEDs radiations with or without the use of concentrator respectively. Equal exposure durations and light fluences were tested. The use of the concentrator-coupled LEDs source revealed an activation of blood movement immediately after LEDs exposure, an effect not attainable by the LEDs source without the concentrator even at extended exposure time. Promising futures for the treatment of inflammation, tissue repair and skin rejuvenation could be expected by adopting this simple technique.

Microbial UV fluence-response assessment using a novel UV-LED collimated beam system.

Science.gov (United States)

Bowker, Colleen; Sain, Amanda; Shatalov, Max; Ducoste, Joel

2011-02-01

A research study has been performed to determine the ultraviolet (UV) fluence-response of several target non-pathogenic microorganisms to UV light emitting diodes (UV-LEDs) by performing collimated beam tests. UV-LEDs do not contain toxic mercury, offer design flexibility due to their small size, and have a longer operational life than mercury lamps. Comsol Multiphysics was utilized to create an optimal UV-LED collimated beam design based on number and spacing of UV-LEDs and distance of the sample from the light source while minimizing the overall cost. The optimized UV-LED collimated beam apparatus and a low-pressure mercury lamp collimated beam apparatus were used to determine the UV fluence-response of three surrogate microorganisms (Escherichia coli, MS-2, T7) to 255 nm UV-LEDs, 275 nm UV-LEDs, and 254 nm low-pressure mercury lamps. Irradiation by low-pressure mercury lamps produced greater E. coli and MS-2 inactivation than 255 nm and 275 nm UV-LEDs and similar T7 inactivation to irradiation by 275 nm UV-LEDs. The 275 nm UV-LEDs produced more efficient T7 and E. coli inactivation than 255 nm UV-LEDs while both 255 nm and 275 nm UV-LEDs produced comparable microbial inactivation for MS-2. Differences may have been caused by a departure from the time-dose reciprocity law due to microbial repair mechanisms. Copyright © 2010 Elsevier Ltd. All rights reserved.

Three consecutive days of application of LED therapy is necessary to inhibit experimentally induced root resorption in rats: a microtomographic study.

Science.gov (United States)

Higashi, Dayla Thyeme; Andrello, Avacir Casanova; Tondelli, Pedro Marcelo; de Oliveira Toginho Filho, Dari; de Paula Ramos, Solange

2017-01-01

Previous studies have suggested that phototherapy may modulate orthodontic tooth movement and the incidence of root resorption. We aimed to identify a minimal dose-response relationship to LED therapy with regard to orthodontic tooth movement (OTM) and root resorption in rats. Forty-eight male Wistar rats were divided into six groups with equal and random distribution: control (C) no intervention; three daily LED irradiation (CLED); submitted only to OTM (RR); OTM and LED irradiation on the first day (LED1); OTM and two LED irradiation on the first and second days (LED2); and OTM and three LED irradiation on the first, second, and third days (LED3). Orthodontic appliance was installed in groups RR, LED1, LED2, and LED3 to promote OTM. Animals from groups CLED, LED1, LED2, and LED3 received LED therapy (940 nm, 4 J, 4 J/cm2) according to each group of treatment. After 7 days, all the animals were sacrificed. The jaws were fixed and scanned with microtomography (micro-CT). The micro-CT images were reconstructed on 2D and 3D models. These models were used to identify and measure root resorption number and dimensions (diameter, depth, and volume). The distance between the first and second molars was used to verify tooth displacement. The results showed that LED3 group had significantly lower number of root resorption. The root resorption dimensions (diameter and depth) had no significant differences among the experimental groups. LED3 group had significant tooth displacement in relation to C and CLED groups. In conclusion, three daily LED therapy doses are required to inhibit root resorption after appliance of orthodontic forces.

Improving “color rendering” of LED lighting for the growth of lettuce

Science.gov (United States)

Han, Tao; Vaganov, Vitaliy; Cao, Shixiu; Li, Qiang; Ling, Lili; Cheng, Xiaoyao; Peng, Lingling; Zhang, Congzhi; Yakovlev, Alexey N.; Zhong, Yang; Tu, Mingjing

2017-04-01

Light plays a vital role on the growth and development of plant. On the base of white light with high color rendering to the benefit of human survival and life, we proposed to improve “color rendering” of LED lighting for accelerating the growth of lettuce. Seven spectral LED lights were adopted to irradiate the lettuces under 150 μmol·m-2·s-1 for a 16 hd-1 photoperiod. The leaf area and number profiles, plant biomass, and photosynthetic rate under the as-prepared LED light treatments were investigated. We let the absorption spectrum of fresh leaf be the emission spectrum of ideal light and then evaluate the “color rendering” of as-prepared LED lights by the Pearson product-moment correlation coefficient and CIE chromaticity coordinates. Under the irradiation of red-yellow-blue light with high correlation coefficient of 0.587, the dry weights and leaf growth rate are 2-3 times as high as the sharp red-blue light. The optimized LED light for lettuce growth can be presumed to be limited to the angle (about 75°) between the vectors passed through the ideal light in the CIE chromaticity coordinates. These findings open up a new idea to assess and find the optimized LED light for plant growth.

Chapter 2: Irradiators

Energy Technology Data Exchange (ETDEWEB)

NONE

2018-04-01

The chapter 2 presents the subjects: 1) gamma irradiators which includes: Category-I gamma irradiators (self-contained); Category-II gamma irradiators (panoramic and dry storage); Category-III gamma irradiators (self-contained in water); Category-IV gamma irradiators (panoramic and wet storage); source rack for Category-IV gamma irradiators; product transport system for Category-IV gamma irradiators; radiation shield for gamma irradiators; 2) accelerators which includes: Category-I Accelerators (shielded irradiator); Category-II Accelerators (irradiator inside a shielded room); Irradiation application examples.

Irradiation of laboratory animal diets

International Nuclear Information System (INIS)

Adamiker, D.

1976-01-01

The increasing demand for well-defined, standardized laboratory animals fr use in experimental research has led to the development of many new methods aimed at keeping the animals free of pathogenic micro-organisms. In this respect the problem of contaminated feeds has become more and more widely recognized. Chemial treatments and heat-treatments, which are the methods most commonly used at present, do have many disadvantages and this has led to an increasing interest in the application of irradiation for sterilizing animal feeds. The author reviews in some detail the various feeding studies which have been performed to date to establish whether or not irradiated feeds are safe for consumption. Much attention is now being given to feed irradiation throughout the world; it is estimated, for example, that approximately 700 tons of feed are already being irradiated per year and that this amount is likely to increase steadily in the future. These activities and recent developments are also briefly reviewed. (author)

In vitro effect of 470 nm LED (Light Emitting Diode in keloid fibroblasts Efeito in vitro do LED (Light Emitting Diode de 470 nm em fibroblastos de quelóide

Directory of Open Access Journals (Sweden)

Silvilena Bonatti

2011-02-01

Full Text Available Purpose: To quantify keloid fibroblasts after irradiation with 470nm blue LED, in vitro. Methods: Fibroblasts from keloid and adjacent skin have been obtained from 6 patients. Cells have been cultivated and maintained in DMEM culture medium. In Petri dishes, they were irradiated with energy doses of 6J, 12J and 18J. After 24 h, counting was done by the average of the triplicates for each sample. Results: There were no significant differences in the number of irradiated keloid fibroblasts at the studied doses (p=0.261. In adjacent skin fibroblasts, differences were observed (p=0.025 concerning the doses of 18 J and 6 J (p=0.03. Conclusions: There was a reduction in the number of adjacent skin fibroblasts irradiated with 470nm blue LED at the energy dose of 18 J compared to the ones irradiated at the energy dose of 6 J. There were no changes in keloid fibroblasts counting at any of the doses applied, 24 h after irradiation.Objetivo: Quantificar fibroblastos de quelóide após irradiação com LED azul de 470nm, in vitro. Métodos: Foram obtidos fibroblastos de quelóide e pele adjacente, de seis pacientes. As células foram cultivadas e mantidas em meio de cultura DMEM. Em placas de Petri, receberam irradiação com doses de energia de 6J, 12J e 18J. Após 24 horas a contagem foi feita pela média da triplicata para cada amostra. Resultados: Não houve diferença na quantidade de fibroblastos de quelóide irradiados nas doses estudadas (p=0,261. Observou-se diferença nos fibroblastos de pele adjacente (p=0,025, com relação às doses de 18 J e 6 J (p=0,03. Conclusões: Houve redução dos fibroblastos de pele adjacente irradiados com LED azul de 470 nm na dose de energia de 18 J em relação à dose de 6 J. Não houve alteração na quantidade de fibroblastos de quelóide nas doses aplicadas após 24 horas da irradiação.

High Power UV LED Industrial Curing Systems

Energy Technology Data Exchange (ETDEWEB)

Karlicek, Robert, F., Jr; Sargent, Robert

2012-05-14

UV curing is a green technology that is largely underutilized because UV radiation sources like Hg Lamps are unreliable and difficult to use. High Power UV LEDs are now efficient enough to replace Hg Lamps, and offer significantly improved performance relative to Hg Lamps. In this study, a modular, scalable high power UV LED curing system was designed and tested, performing well in industrial coating evaluations. In order to achieve mechanical form factors similar to commercial Hg Lamp systems, a new patent pending design was employed enabling high irradiance at long working distances. While high power UV LEDs are currently only available at longer UVA wavelengths, rapid progress on UVC LEDs and the development of new formulations designed specifically for use with UV LED sources will converge to drive more rapid adoption of UV curing technology. An assessment of the environmental impact of replacing Hg Lamp systems with UV LED systems was performed. Since UV curing is used in only a small portion of the industrial printing, painting and coating markets, the ease of use of UV LED systems should increase the use of UV curing technology. Even a small penetration of the significant number of industrial applications still using oven curing and drying will lead to significant reductions in energy consumption and reductions in the emission of green house gases and solvent emissions.

Raman study of the effect of LED light on grafted bone defects

Science.gov (United States)

Soares, Luiz G. G. P.; Aciole, Jouber M. S.; Aciole, Gilbeth T. S.; Barbosa, Artur F. S.; Silveira-Júnior, Landulfo; Pinheiro, Antônio L. B.

2013-03-01

Benefits of the isolated or combined use light and biomaterials on bone healing have been suggested. Our group has used several models to assess the effects of laser on bone. A Raman spectral analysis on surgical bone defects grafted or not with Hydroxyapatite (HA), treated or not with LED was carried out. 40 rats were divided into 4 groups. On Group I the defect was filled with the clot. On Group II, the defect was filled with the HA. On groups III the defect was filled with Clot and further irradiated with LED and on group IV the defects was filled with the HA and further irradiated with LED. LED (λ850 +/- 10nm, 150mW, A= 0.5cm2, 68s, 20 J/cm2 per session, 140 J/cm2 per treatment) was applied at 48 h intervals during 15 days. Specimens were taken after 15 and 30 days after surgery and kept on liquid nitrogen, and underwent Raman analysis. For this, the peak of hydroxyapatite (~960 cm-1) was used as marker of bone mineralization. Significant difference was observed at both times (p<0.05). When the biomaterial was used higher peaks were observed. Association with LED further improved the intensity. Conclusion: It is concluded that LED light improved the effect of the HA.

The effects of LED illumination spectra and intensity on carotenoid content in Brassicaceae microgreens.

Science.gov (United States)

Brazaitytė, Aušra; Sakalauskienė, Sandra; Samuolienė, Giedrė; Jankauskienė, Julė; Viršilė, Akvilė; Novičkovas, Algirdas; Sirtautas, Ramūnas; Miliauskienė, Jurga; Vaštakaitė, Viktorija; Dabašinskas, Laurynas; Duchovskis, Pavelas

2015-04-15

The objective of this study was to evaluate the effects of irradiance levels and spectra produced by solid-state light-emitting diodes (LEDs) on carotenoid content and composition changes in Brassicaceae microgreens. A system of five high-power, solid-state lighting modules with standard 447-, 638-, 665-, and 731-nm LEDs was used in the experiments. Two experiments were performed: (1) evaluation of LED irradiance levels of 545, 440, 330, 220, and 110 μmol m(-2) s(-1) photosynthetically active flux density (PPFD) and (2) evaluation of the effects of 520-, 595-, and 622-nm LEDs supplemental to the standard set of LEDs. Concentrations of various carotenoids in red pak choi and tatsoi were higher under illumination of 330-440 μmol m(-2) s(-1) and at 110-220 μmol m(-2) s(-1) in mustard. All supplemental wavelengths increased total carotenoid content in mustard but decreased it in red pak choi. Carotenoid content increased in tatsoi under supplemental yellow light. Copyright © 2014 Elsevier Ltd. All rights reserved.

Infrared LED Array For Silicon Strip Detector Qualification

CERN Document Server

Dirkes, Guido; Hartmann, Frank; Heier, Stefan; Schwerdtfeger, Wolfgang; Waldschmitt, M; Weiler, K W; Weseler, Siegfried

2003-01-01

The enormous amount of silicon strip detector modules for the CMS tracker requires a test-sytem to allow qualification of each individual detector module and its front-end electronics within minutes. The objective is to test the detector with a physical signal. Signals are generated in the detector by illumination with lightpulses emitted by a LED at 950~nm and with a rise time of 10~ns. In order to avoid a detector moving, an array of 64 LEDs is used, overlaping the complete detector width. The total length of an array is 15~cm. The spot size of an individual LED is controlled by apertures to illuminate about 25 strips. Furthermore it is possible to simulate the high leakage current of irradiated sensors by constant illumination of the sensor. This provides an effective mean to identfy pinholes on a sensor.

BiliLED low cost neonatal phototherapy, from prototype to industry

Energy Technology Data Exchange (ETDEWEB)

Geido, Daniel; Failache, Horacio [Instituto de Fisica de la Facultad de Ingenieria - Universidad de la Republica, Montevideo (Uruguay); Simini, Franco [Nucleo de Ingenieria Biomedica de las Facultades de Medicina e Ingenieria (Uruguay); Hospital de ClInicas. Av Italia S/N. Piso 15 sala 2, 11600 Montevideo (Uruguay)

2007-11-15

BiliLED is a phototherapy instrument designed to reduce bilirrubin blood rates in new born babies with jaundice. The light source is centred at 470 nm with a bandwidth of 35 nm and includes a matrix of 196 (14x14) InGaN LEDs. The optical elements are designed to maximize the light intensity useful for treatment, with a small number of LEDs in a compact and low cost unit. The optic array is such that every LED illuminates all the treatment area, which ensures redundancy and, thus, a high reliability not to be found in single-lamp instruments. Thermal dissipation and cost of BiliLED are both an order-of-magnitude smaller than conventional therapy lamps. BiliLED adjusts coetaneous irradiation with a feedback loop to compensate the loss or aging of LEDs achieving a calibrated light source for over a decade of use. A clinical trial in 20 hyperbilirrubinaemia patients shows 16% bilirrubin degradation within 24 hours of treatment, higher than most lamp phototherapy instruments. The steps from prototype to commercial model are described.

BiliLED low cost neonatal phototherapy, from prototype to industry

Science.gov (United States)

Geido, Daniel; Failache, Horacio; Simini, Franco

2007-11-01

BiliLED is a phototherapy instrument designed to reduce bilirrubin blood rates in new born babies with jaundice. The light source is centred at 470 nm with a bandwidth of 35 nm and includes a matrix of 196 (14×14) InGaN LEDs. The optical elements are designed to maximize the light intensity useful for treatment, with a small number of LEDs in a compact and low cost unit. The optic array is such that every LED illuminates all the treatment area, which ensures redundancy and, thus, a high reliability not to be found in single-lamp instruments. Thermal dissipation and cost of BiliLED are both an order-of-magnitude smaller than conventional therapy lamps. BiliLED adjusts coetaneous irradiation with a feedback loop to compensate the loss or aging of LEDs achieving a calibrated light source for over a decade of use. A clinical trial in 20 hyperbilirrubinaemia patients shows 16% bilirrubin degradation within 24 hours of treatment, higher than most lamp phototherapy instruments. The steps from prototype to commercial model are described.

BiliLED low cost neonatal phototherapy, from prototype to industry

International Nuclear Information System (INIS)

Geido, Daniel; Failache, Horacio; Simini, Franco

2007-01-01

BiliLED is a phototherapy instrument designed to reduce bilirrubin blood rates in new born babies with jaundice. The light source is centred at 470 nm with a bandwidth of 35 nm and includes a matrix of 196 (14x14) InGaN LEDs. The optical elements are designed to maximize the light intensity useful for treatment, with a small number of LEDs in a compact and low cost unit. The optic array is such that every LED illuminates all the treatment area, which ensures redundancy and, thus, a high reliability not to be found in single-lamp instruments. Thermal dissipation and cost of BiliLED are both an order-of-magnitude smaller than conventional therapy lamps. BiliLED adjusts coetaneous irradiation with a feedback loop to compensate the loss or aging of LEDs achieving a calibrated light source for over a decade of use. A clinical trial in 20 hyperbilirrubinaemia patients shows 16% bilirrubin degradation within 24 hours of treatment, higher than most lamp phototherapy instruments. The steps from prototype to commercial model are described

Studying Light Color using White LED Lighting

Science.gov (United States)

Yamagishi, Misako; Yamaba, Kazuo; Nagata, Manori; Kubo, Chiho; Nokura, Kunihiro

Recently, white Light Emitting Diodes (LEDs) are receiving attention worldwide as new lighting devices. This study examined effects of a lighting application on performance using white LEDs. The light color—the correlated color temperature (CCT) —was assessed. It affected to psychological states and physiological conditions. Three CCT conditions were respectively set for the experiment: 2500 K, 5000 K, and 8200 K. In all, 20 younger subjects (20-30 years old), 15 middle-aged to elderly subjects (45-60 years old) and 12 elderly subjects (over 65 years-old) participated. They were presented a Numerical Verification (NV) task for performance measurement. The psychological states on performance were evaluated using the lighting assessment questionnaire. The physiological conditions were recorded using an electrocardiograph. Results show that the effects of CCT differ among age groups. Especially, the performance of younger subjects might differ from CCT conditions; elderly subjects are affected by CCT condition because of their visual acuity or response to contrast of objects.

MOSFET Loss Evaluation for a Low-Power Stand-Alone Photovoltaic-LED System

DEFF Research Database (Denmark)

Mira Albert, Maria del Carmen; Knott, Arnold; Andersen, Michael A. E.

2015-01-01

This paper presents a performance evaluation and comparison of state-of-the-art low voltage Si MOSFETs for a stand-alone photovoltaic-LED Light to Light (LtL) system. The complete system is formed by two cascaded converters that will be optimized for a determined solar irradiation and LED...... illumination profiles. The comparison is performed based on dynamic characterization and evaluation of the devices energy loss at different current levels....

The nucleic acids as early indicators of the recovery of patients subjected to total body irradiation for bone marrow transplant

International Nuclear Information System (INIS)

Morera Carrillo, L.M.; Garcia Lima, O.; Carnot, J.; Cardenas, J.

2000-01-01

The possibility to use the concentration of nucleic acids as an early indicator for the recovery of individuals exposed to high radiation was valued in 30 patients subjected to a dose of 10 Gy (cobalt 60) in two or three sessions of total body irradiation for bone marrow transplants. The determination of the concentration of the nucleic acids was carried out prior to the irradiation, and later in different periods until the patients discharge. The behaviour of indicate such as alpha amylase serics transaminases, glicemics, alkaline phosphatase and others was also studied

Semiconductor lasers and herterojunction leds

CERN Document Server

Kressel, Henry

2012-01-01

Semiconductor Lasers and Heterojunction LEDs presents an introduction to the subject of semiconductor lasers and heterojunction LEDs. The book reviews relevant basic solid-state and electromagnetic principles; the relevant concepts in solid state physics; and the p-n junctions and heterojunctions. The text also describes stimulated emission and gain; the relevant concepts in electromagnetic field theory; and the modes in laser structures. The relation between electrical and optical properties of laser diodes; epitaxial technology; binary III-V compounds; and diode fabrication are also consider

Lens of controllable optical field with thin film metallic glasses for UV-LEDs.

Science.gov (United States)

Pan, C T; Chen, Y C; Lin, Po-Hung; Hsieh, C C; Hsu, F T; Lin, Po-Hsun; Chang, C M; Hsu, J H; Huang, J C

2014-06-16

In the exposure process of photolithography, a free-form lens is designed and fabricated for UV-LED (Ultraviolet Light-Emitting Diode). Thin film metallic glasses (TFMG) are adopted as UV reflection layers to enhance the irradiance and uniformity. The Polydimethylsiloxane (PDMS) with high transmittance is used as the lens material. The 3-D fast printing is attempted to make the mold of the lens. The results show that the average irradiance can be enhanced by 6.5~6.7%, and high uniformity of 85~86% can be obtained. Exposure on commercial thick photoresist using this UV-LED system shows 3~5% dimensional deviation, lower than the 6~8% deviation for commercial mercury lamp system. This current system shows promising potential to replace the conventional mercury exposure systems.

Effect of Laser and LED on Enzymatic Production of Ceramide

DEFF Research Database (Denmark)

Hongyu, Zhang; Zhang, Long; Tidemand-Lichtenberg, Peter

2011-01-01

using HPTLC (high performance thin-layer chromatography) at 0.5, 1, 2, 3, 4, 6, 17, 24 h after irradiation. The duration of effect was evaluated from the experimental data. The results show that enzyme activity can be increased by using both laser and LED sources whose wavelength is located within...

ODS alloys for structures subjected to irradiation

International Nuclear Information System (INIS)

Carlan, Y. de

2010-01-01

ODS (oxide-dispersion-strengthened) materials are considered for cladding purposes for the fourth-generation sodium-cooled fast reactors. ODS materials afford many benefits. Indeed, these high-performance materials combine, at the same time, remarkable mechanical strength, in hot conditions, and outstanding irradiation behavior. New ODS steel grades, exhibiting better performance levels than the last-generation austenitic steels, afford not only negligible swelling under irradiation, owing to their 'ferritic' body-centered cubic structure - by contrast to austenitic grades, which feature a face-centered cubic structure - but equally outstanding creep properties, owing to the nano-reinforcements present in the matrix. ODS materials are obtained by powder metallurgy, the first fabrication step involves co-grinding a metal powder together with yttrium oxide (Y 2 O 3 ) powder. At this stage, an iron oxide may also be added, or an yttrium-rich intermetallic compound in order to provide the amounts of yttrium, and oxygen required for the formation of nano-oxides. The metal powder consists of a powder pre-alloyed to the chemical composition of the desired material. Once the powder has been obtained, consolidation of the ODS materials is achieved either by hot extrusion, or by hot isostatic pressing. (A.C.)

Effects of LED phototherapy on bone defects grafted with MTA, bone morphogenetic proteins and guided bone regeneration: a Raman spectroscopic study.

Science.gov (United States)

Pinheiro, Antonio L B; Soares, Luiz G P; Cangussú, Maria Cristina T; Santos, Nicole R S; Barbosa, Artur Felipe S; Silveira Júnior, Landulfo

2012-09-01

We studied peaks of calcium hydroxyapatite (CHA) and protein and lipid CH groups in defects grafted with mineral trioxide aggregate (MTA) treated or not with LED irradiation, bone morphogenetic proteins and guided bone regeneration. A total of 90 rats were divided into ten groups each of which was subdivided into three subgroups (evaluated at 15, 21 and 30 days after surgery). Defects were irradiated with LED light (wavelength 850 ± 10 nm) at 48-h intervals for 15 days. Raman readings were taken at the surface of the defects. There were no statistically significant differences in the CHA peaks among the nonirradiated defects at any of the experimental time-points. On the other hand, there were significant differences between the defects filled with blood clot and the irradiated defects at all time-points (p Raman spectral analysis indicate that infrared LED light irradiation improves the deposition of CHA in healing bone grafted or not with MTA.

On kinetic study of blood cells and bone marrow under fractionated irradiation

International Nuclear Information System (INIS)

Teterina, V.I.

1977-01-01

To study the changes in the cellular composition of bone marrow during irradiation experiments on the guinea pigs have been carried out. Animals were subjected to fractionated irradiation; daily dose of 12 rad, total doses of 250, 500, 750, 1000 and 1500 rad, total duration of radiation of 1,2,3,4 and 6 monts. Experiments have shown that with small levels of total doses of the ionizing radiation haemopoiesis in the bone marrow reached its maximum. This led to suppression of anaemia and profound leukaemia in the peripheral blood. With the increase of total doses phase of insufficient compensation of harmful effects of radiation has been reached, which with continuing radiation may lead to the exhaustion of reserve possibilities of bone marrow and to the development of pancytopenia

Antioxidative system in the liver of rates subjected to combined irradiation injury

International Nuclear Information System (INIS)

Simovic, M.; Stanimirovic, D.; Ivanovic, L.; Markovic, M.; Letic-Gavrilovic, A.; Jovic, P.; Savic, J.; Spasic, M.; Saicic, Z.S.

1991-01-01

Until the Chernobyl nuclear plant catastrophe, exposure to radiation combined with other forms of injuries was usually considered as a hazard of nuclear war. The effect of combined irradiation injuries are often defined as the simultaneous effect of irradiation and another noxious stimulus. In the authors' opinion (1) one may talk about combined irradiation injuries (CII) only in the case when the general response of an organism to traumatization is the combination of biological reactions to at least two different etiologic noxious stimuli of which one is irradiation. One of the basic problems of combined injuries in general and CII in particular, is the syndrome of mutual aggravation (SMA) expressed through a very high (potentiated) lethality. The real mechanism(s) of this syndrome is still unknown. In our model of combined irradiation injury, potentiation of irradiation effect was smaller if animals were irradiated in the hypometabolic (open-quotes ebbclose quotes) compared to the hypermetabolic (open-quotes flowclose quotes) phase after thermal injury. Since the oxygen uptake is greater in the hypermetabolic phase the free radical production is also greater. On the other hand, the transition of hypometabolic to hypermetabolic phase could be analogous to a hypoxia/reoxygenation state. According to Granger et al. this state induces an increase in free radical production. When irradiation injury follows scalding it induces a new flux of free radicals. As a result the antioxidative defense of an organism could be overwhelmed and a disturbance of oxidative-antioxidative processes might occur. Thus, the authors suppose that overwhelmed antioxidative defense could be the reason for potentiated lethality in combined irradiation injury. 12 refs., 2 tabs

Radiation effects in pigtailed GaAs and GaA1As LEDs

International Nuclear Information System (INIS)

Barnes, C.E.

1981-06-01

Permanent and transient radiation effects have been studied in Plessey pigtailed, high radiance GaAs and GaAlAs LEDs using neutron, gamma ray and X-ray sources. The radiation-induced source of degradation in these devices was determined by also examining both bare, unpigtailed LEDs and separate samples of the Corning fibers used as pigtails. No transient effects were observed in the unpigtailed LEDs during either pulsed neutron or X-ray exposure. In contrast, the Corning doped silica fibers exhibited strong transient attenuation following pulsed X-ray bombardment. Permanent neutron damage in these pigtailed LEDs consisted essentially of light output degradation in the LED itself. Permanent gamma ray effects due to a Co-60 irradiation of 1 megarad were restricted to a small increase in attenuation in the fiber. The two primary radiation effects were then transient attenuation in the fiber pigtail and permanent neutron-induced degradation of the LED

Types of repair in radiosensitive organs of mice subjected to continuous γ-irradiation

International Nuclear Information System (INIS)

Li Yuanmin; Hu Fenghua; Gao Yabin

1990-01-01

LACA mice were whole-body irradiated with 1 Gy continuous γ-irradiation for 22 hours daily. Animals were divided into groups according to different cumulative doses of 10, 15, 20, 25 and 30 Gy, and were sacrificed at different intervals after the termination of irradiation when the above doses were reached. Radiosensitive organs were stduied by determination of quantitative indices and microscopic examination of histopathological sections. Three types of repair of radiation damages were found in radiosensitive organs, i.e. (1) full repair during irradiation in small intestines, (2) repair only after cessation of irradiation in hemopoietic and lymphoid tissues, and (3) continuing damage even after cessation of irradiation in testes

Radiation hardness and lifetime studies of LEDs and VCSELs for the optical readout of the ATLAS SCT

CERN Document Server

Beringer, J; Mommsen, R K; Nickerson, R B; Weidberg, A R; Monnier, E; Hou, H Q; Lear, K L

1999-01-01

We study the radiation hardness and the lifetime of Light Emitting Diodes (LEDs) and Vertical Cavity Surface Emitting Laser diodes (VCSELs) in the context of the development of the optical readout for the ATLAS SemiConductor Tracker (SCT) at LHC. About 170 LEDs from two different manufacturers and about 130 VCSELs were irradiated with neutron and proton fluences equivalent to (and in some cases more than twice as high as) the combined neutral and charged particle fluence of about 5x10 sup 1 sup 4 n (1 MeV eq. in GaAs)/cm sup 2 expected in the ATLAS inner detector. We report on the radiation damage and the conditions required for its partial annealing under forward bias, we calculate radiation damage constants, and we present post-irradiation failure rates for LEDs and VCSELs. The lifetime after irradiation was investigated by operating the diodes at an elevated temperature of 50 degree sign C for several months, resulting in operating times corresponding to up to 70 years of operation in the ATLAS SCT. From o...

Biology of food irradiation

International Nuclear Information System (INIS)

Murray, D.R.

1990-01-01

The author presents his arguments for food scientists and biologists that the hazards of food irradiation outweigh the benefits. The subject is discussed in the following sections: introduction (units, mutagenesis, seed viability), history of food irradiation, effects of irradiation on organoleptic qualities of staple foods, radiolytic products and selective destruction of nutrients, production of microbial toxins in stored irradiated foods and loss of quality in wheat, deleterious consequences of eating irradiated foods, misrepresentation of the facts about food irradiation. (author)

Effects of hyperthermia and X-irradiation on mouse stromal tissue

NARCIS (Netherlands)

Wondergem, J.; Begg, A. C.; Haveman, J.

1986-01-01

The sensitivity of normal stroma to heat, irradiation and heat combined with irradiation has been studied using the tumour bed effect (TBE) assay. Irradiation before implantation led to a TBE. This TBE was dose dependent below 15 Gy, the TBE remaining relatively constant above 15 Gy. The interval

Study on Healing Environment Using Green, Blue and Red LED and Aroma

Science.gov (United States)

Miyaho, Noriharu; Konno, Noriko; Shimada, Takamasa

In this paper we evaluated the effects of 1/f fluctuation of Green LED light emitted from the specific object by using psychological and physiological experimental tests of spectral electroencephalogram (EEG) topography. In addition, we also verified that the combination of appropriate aroma, blue LED light irradiation and music such as “Mozart: Serenade in Eine Kleine Nacht Musik” has improved mental healing conditions. We confirmed the possibility that the effect of “Healing” would be improved by the above mentioned environments.

LED photochemotherapy against Staphylococcus aureus: an in vitro study

Science.gov (United States)

de Oliveira, Susana C. P. S.; Monteiro, Juliana S. C.; Pires-Santos, Gustavo M.; Sampaio, Fernando José Pires; Soares, Luiz Guilherme P.; Soares, Amanda P.; Pinheiro, Antônio L. B.

2018-02-01

Bacterial resistance to antibiotics is reality and need for alternative treatments is urgent. The aim of this work was to evaluate, in vitro, the effect of LED photochemotherapy on Staphylococcus aureus (ATCC 23529) using 25 μg / mL of phenothiazine compound combined with LED light (λ632 +/- 2ηm) using 12 J/cm2 energy density. The experiments were carried out in triplicate and the samples were divided into groups: Control, Irradiated (treated only with light), Photosensitizer (treated only in the presence of the dye), LED-Photochemotherapy (treatment with light associated with dye). Counts of the colony forming units and the data obtained were statistically analyzed (ANOVA, Tukey's test, p<0.05). The present study demonstrated that the efficacy of LED-Photochemotherapy as the use of 25 μg/mL x 12 J/cm2 caused 91.57 % of inhibition of bacterial growth. It is concluded that using energy density of 12 J/cm2 associated to 25 μg/mL caused high in vitro inhibition of S. aureus.

Enhanced mass transfer during solid-liquid extraction of gamma-irradiated red beetroot

International Nuclear Information System (INIS)

Nayak, Chetan A.; Chethana, S.; Rastogi, N.K.; Raghavarao, K.S.M.S.

2006-01-01

The exposure to gamma-irradiation pretreatment increases cell wall permeabilization, resulting in loss of turgor pressure, which led to the increase of extractability of betanin from red beetroot. The degree of extraction of betanin was investigated using gamma irradiation as a pretreatment prior to the solid-liquid extraction process and compared with control beetroot samples. The beetroot subjected to different doses of gamma irradiation (2.5, 5.0, 7.5, 10.0 kGy) and control was dipped in an acetic acid medium (1% v/v) to extract the betanin. The diffusion coefficients for betanin as well as ionic component were estimated considering Fickian diffusion. The results indicated an increase in the diffusion coefficient of betanin (0.302x10 -9 -0.463x10 -9 m 2 /s) and ionic component (0.248x10 -9 -0.453x10 -9 m 2 /s) as the dose rate increased (from 2.5 to 10.0 kGy). The degradation constant was found to increase (0.050-0.079 min -1 ) with an increase gamma-irradiation doses (2.5-10.0 kGy), indicating lower stability of the betanin as compared to control sample at 65 deg. C

Irradiation-induced patterning in dilute Cu–Fe alloys

International Nuclear Information System (INIS)

Stumphy, B.; Chee, S.W.; Vo, N.Q.; Averback, R.S.; Bellon, P.; Ghafari, M.

2014-01-01

Compositional patterning in dilute Cu 1−x Fe x (x ≈ 12%) induced by 1.8 MeV Kr + irradiation was studied as a function of temperature using atom probe tomography. Irradiation near room temperature led to homogenization of the sample, whereas irradiation at 300 °C and above led to precipitation and macroscopic coarsening. Between these two temperatures the irradiated alloys formed steady state patterns of composition where precipitates grew to a fixed size. The size in this regime increased somewhat with temperature. It was also observed that the steady state concentrations of Fe in Cu matrix and Cu in the Fe precipitates both greatly exceeded their equilibrium solubilities, with the degree of supersaturation in each phase decreasing with increasing temperature. In the macroscopic coarsening regime, the Fe-rich precipitates showed indications of a “cherry-pit” structure, with Cu precipitates forming within the Fe precipitates. In the patterning regime, interfaces between Fe-rich precipitates and the Cu-rich matrix were irregular and diffuse

Novel Carbazole Skeleton-Based Photoinitiators for LED Polymerization and LED Projector 3D Printing

Directory of Open Access Journals (Sweden)

Assi Al Mousawi

2017-12-01

Full Text Available Radical chemistry is a very convenient way to produce polymer materials. Here, an application of a particular photoinduced radical chemistry is illustrated. Seven new carbazole derivatives Cd1–Cd7 are incorporated and proposed as high performance near-UV photoinitiators for both the free radical polymerization (FRP of (methacrylates and the cationic polymerization (CP of epoxides utilizing Light Emitting Diodes LEDs @405 nm. Excellent polymerization-initiating abilities are found and high final reactive function conversions are obtained. Interestingly, these new derivatives display much better near-UV polymerization-initiating abilities compared to a reference UV absorbing carbazole (CARET 9H-carbazole-9-ethanol demonstrating that the new substituents have good ability to red shift the absorption of the proposed photoinitiators. All the more strikingly, in combination with iodonium salt, Cd1–Cd7 are likewise preferred as cationic photoinitiators over the notable photoinitiator bis(2,4,6-trimethylbenzoylphenylphosphine oxide (BAPO for mild irradiation conditions featuring their remarkable reactivity. In particular their utilization in the preparation of new cationic resins for LED projector 3D printing is envisioned. A full picture of the included photochemical mechanisms is given.

Design and radiation tests on a LED based emergency evacuation directional lighting

CERN Document Server

Trikoupis, Nikolaos

2017-01-01

A LED (Light Emitting Diode) based directional lighting system has been designed to indicate the best evacuation direction for applications like the Large Hadron Collider (LHC) tunnel. The design includes constraints for redundancy required by safety systems and for components selection by radiation effects. Most of the literature for radiation effects on LEDs concern digital communications systems, although some recent reports do exist for visible spectrum power LEDs and the reduction in light output versus dose is coherent with the results presented in this paper. Prototype lighting units were irradiated in CERN’s CHARM facility up to a Total Integrated Dose (TID) of 870 Gy and no failures were observed. This paper describes the basic design, presents field tests and the effects of radiation on the LEDs luminance.

Food irradiation: Activities and potentialities

Science.gov (United States)

Doellstaedt, R.; Huebner, G.

After the acceptance of food irradiation up to an overall average dose of 10 kGy recommended by the Joint FAO/IAEA/WHO Expert Committee on the Wholesomeness of Irradiated Food in October 1980, the G.D.R. started a programme for the development of techniques for food irradiation. A special onion irradiator was designed and built as a pilot plant for studying technological and economic parameters of the irradiation of onions. The new principle of bulk-cargo irradiation allows the integration of this technology into the usual harvest technology for onions on the way from field to storage. Scientific and applied research work has been carried out in the past 3 yr on the irradiation of spices, potatoes, eviscerated chicken, animal feeds, fodder yeast, drugs and vaccines. In connection with the irradiation of eviscerated chicken, fodder yeast and animal feeds the basis of an antisalmonella programme has been discussed. Germ-count-reduced spices were employed for the production of test charges of preserves and tinned products. The results have led to the decision to design and build a new multipurpose irradiator for food irradiation. In order to cover the legal aspects of food irradiation the Ministry of Health issued regulations concerning the recommendation of irradiated food in the G.D.R.

Economics of gamma irradiation processing

International Nuclear Information System (INIS)

Tani, Toshio

1980-01-01

The gamma-ray irradiation business started at the Takasaki Laboratory of Japan Atomic Energy Research Institute. The irradiation facilities were constructed thereafter at various sites. The facilities must accept various types of irradiation, and must be constructed as multi-purpose facilities. The cost of irradiation consists of the cost of gamma sources, construction expense, personnel expense, management expense, and bank interest. Most of the expenses are considered to be fixed expense, and the amount of irradiation treatment decides the original costs of work. The relation between the irradiation dose and the construction expense shows the larger facility is more economical. The increase of amount of treatment reduces the original cost. The utilization efficiency becomes important when the amount of treatment and the source intensity exceed some values. The principal subjects of gamma-ray irradiation business are the sterilization of medical tools and foods for aseptic animals, the improvement of quality of plastic goods, and the irradiation of foods. Among them, the most important subject is the sterilization of medical tools. The cost of gamma irradiation per m 3 in still more expensive than that by ethylene oxide gas sterilization. However, the demand of gamma-ray irradiation is increasing. For the improvement of quality of plastic goods, electron irradiation is more favourable than the gamma irradiation. In near future, the economical balance of gamma irradiation can be achieved. (Kato, T.)

The structural-phenomenological description of plastic anisotropy of H-1 and H-2.5 alloys, subjected to reactors irradiation

International Nuclear Information System (INIS)

Yamshchikov, N.V.; Prasolov, P.F.; Lebedinskij, K.B.

1990-01-01

The structural-phenomenological model of anisotropic single hpc textured polycrystals is described. The formulation of the present model is assumed that the polycrystal is continuous three-dimensional collection of transversal crystallites, the plastic properties which Hill's yield criteria are described. This model is allowed to determine six parameters in the Hill's yield criteria for ortho tropic materials based on only of uniaxial tension test in three directions and crystallographic texture. Yield surfaces of zircaloy alloys at 293 K and 623 K, subjected to irradiation in the reactor with total exposition dose 10 20 n/cm 2 are determined. Strongly influence of irradiation on the plastic behaviour of H-1 and H-2,5 alloys is observed. 2 refs.; 3 figs.; 2 tables. (author)

Food irradiation: progress in Canada

International Nuclear Information System (INIS)

Wilson, B.K.

1985-01-01

The subject is discussed under the headings: food irradiation regulatory situation in Canada; non-regulatory developments (poultry irradiation; fish irradiation; Government willingness to fund industry initiated projects; Government willingness to establish food irradiation research and pilot plant facilities; food industry interest is increasing significantly; Canadian Consumers Association positive response; the emergence of new consulting and entrepreneurial firms). (U.K.)

Raman spectroscopic study of the repair of surgical bone defects grafted or not with biphasic synthetic micro-granular HA + β-calcium triphosphate irradiated or not with λ850 nm LED light.

Science.gov (United States)

Soares, Luiz Guilherme P; Marques, Aparecida Maria C; Guarda, Milena G; Aciole, Jouber Mateus S; Andrade, Aline S; Pinheiro, Antonio Luiz B; Silveira, Landulfo

2014-11-01

The handling of bone losses due to different etiologic factors is difficult and many techniques are aim to improve repair, including a wide range of biomaterials and, recently, photobioengineering. This work aimed to assess, through Raman spectroscopy, the level of bone mineralization using the intensities of the Raman peaks of both inorganic (~960, ~1,070, and 1,077 cm(-1)) and organic (~1,454 and ~1,666 cm(-1)) contents of bone tissue. Forty rats were divided into four groups each subdivided into two subgroups according to the time of sacrifice (15 and 30 days). Surgical bone defects were made on the femur of each animal with a trephine drill. On animals of group clot, the defect was filled only by blood clot, on group LED, the defect filled with the clot was further irradiated. On animals of groups biomaterial and LED + biomaterial, the defect was filled by biomaterial and the last one was further irradiated (λ850 ± 10 nm, 150 mW, Φ ~ 0.5 cm(2), 20 J/cm(2)-session, 140 J/cm(2)-treatment) at 48-h intervals and repeated for 2 weeks. At both 15th and 30th days following sacrifice, samples were taken and analyzed by Raman spectroscopy. At the end of the experimental time, the intensity of hydroxyapatite (HA) (~960 cm(-1)) were higher on group LED + biomaterial and the peaks of both organic content (~1,454 and ~1,666 cm(-1)) and transitional HA (~1,070 and ~1,077 cm(-1)) were lower on the same group. It is concluded that the use of LED phototherapy associated to biomaterial was effective in improving bone healing on bone defects as a result of the increasing deposition of HA measured by Raman spectroscopy.

Dose rate distribution for products irradiated in a semi-industrial irradiation plant. 1st stage

International Nuclear Information System (INIS)

Mangussi, J.

2005-01-01

The model of the bulk product absorbed dose rate distribution in a semi industrial irradiation plant is presented. In this plant the products are subject to a dynamic irradiation process: single-plaque, single-direction, four-passes. The additional two passes, also one on each side of the plaque, serve to minimize the lateral dose variation as well as the depth-dose non-uniformity. The first stage of this model takes only into account the direct absorbed dose rate; the model outputs are the depth-dose distribution and the lateral-dose distribution. The calculated absorbed dose in the bulk product and its uniformity-ratio after the dynamic irradiation process for different products is compared. The model results are in good agreement with the experimental measurements in a bulk of irradiated product; and the air absorbed dose rate in the irradiation chamber behind the product subject to the dynamic irradiation process. (author) [es

Thermal analysis applied to irradiated propolis

Energy Technology Data Exchange (ETDEWEB)

Matsuda, Andrea Harumi; Machado, Luci Brocardo; Mastro, N.L. del E-mail: nelida@usp.br

2002-03-01

Propolis is a resinous hive product, collected by bees. Raw propolis requires a decontamination procedure and irradiation appears as a promising technique for this purpose. The valuable properties of propolis for food and pharmaceutical industries have led to increasing interest in its technological behavior. Thermal analysis is a chemical analysis that gives information about changes on heating of great importance for technological applications. Ground propolis samples were {sup 60}Co gamma irradiated with 0 and 10 kGy. Thermogravimetry curves shown a similar multi-stage decomposition pattern for both irradiated and unirradiated samples up to 600 deg. C. Similarly, through differential scanning calorimetry , a coincidence of melting point of irradiated and unirradiated samples was found. The results suggest that the irradiation process do not interfere on the thermal properties of propolis when irradiated up to 10 kGy.

Food irradiation: Technology transfer in Asia, practical experiences

Science.gov (United States)

Kunstadt, Peter; Eng, P.

1993-10-01

Nordion International Inc., in cooperation with the Thai Office of Atomic Energy for Peace (OAEP) and the Canadian International Development Agency (CIDA) recently completed a unique food irradiation technology transfer project in Thailand. This complete food irradiation technology transfer project included the design and construction of an automatic multipurpose irradiation facility as well as the services of construction and installation management and experts in facility operation, maintenance and training. This paper provides an insight into the many events that led to the succesful conclusion of the world's first complete food irradiation technology transfer project.

Food irradiation: technology transfer in Asia, practical experiences

International Nuclear Information System (INIS)

Kunstadt, P.

1993-01-01

Nordion International Inc., in cooperation with the Thai Office of Atomic Energy for Peace (OAEP) and the Canadian International Development Agency (CIDA) recently completed a unique food irradiation technology transfer project in Thailand. This complete food irradiation technology transfer project included the design and construction of an automatic multipurpose irradiation facility as well as the services of construction and installation management and experts in facility operation, maintenance and training. This paper provides an insight into the many events that led to the successful conclusion of the world's first complete food irradiation technology transfer project. (Author)

GaAs Led based NIEL spectrometer for the space radiation environment

International Nuclear Information System (INIS)

Houdayer, A.J.; Hinrichsen, P.F.; Barry, A.L.; Ng, A.

1999-01-01

A NIEL (non-ionizing-energy-loss) spectrometer for the Mir space station is described. The NIEL spectrometer package contained 20 GaAs LEDs, 10 SiC LEDs and 13 locations for TLD-700s. In order to probe different energy regions of the radiation field, the package is divided into 4 compartments covered by absorbers of varying thicknesses. This device has been submitted to proton irradiation. The effects on both the response time and the intensity of the light were measured as a function of the fluence. One of the advantages of LEDs as radiation monitors is their sensitivity and it is shown that it would be possible to detect a fluence of 4*10 7 p/cm 2 of 10 MeV protons, with sensitivity scaled as 1/E for other energies. (A.C.)

Gas generation from the irradiation of mortar

International Nuclear Information System (INIS)

Lewis, M.A.; Warren, D.W.

1989-01-01

A mortar formulation capable of immobilizing chloride salts with high levels of radioactivity is being developed. As part of the developmental effort, radiation effects are being investigated. The radiolytic generation of gas(es) from irradiated mortar formulations was determined for several formulations with variable salt loadings at several test temperatures. The irradiation of a mortar formulation consisting of cement, slag, fly ash, water and 0 to 10 wt % salt led to the generation of hydrogen. The rate of generation was approximately constant, steady state pressures were not attained and final pressures were comparatively high. Higher salt concentrations were correlated with higher hydrogen generation rates for experiments at ambient temperature while lower rates were observed at 120/degree/C. The irradiation of a mortar consisting of cement, fly ash, water and salt led to the radiolytic generation of both oxygen and hydrogen. The addition of 2 wt % FeS or CaS inhibited oxygen generation and changed the hydrogen production rate. 10 refs., 4 figs., 3 tabs

Fluctuation in hematology values in gamma irradiated rats subjected to pesticide ingestion

Energy Technology Data Exchange (ETDEWEB)

abdel-Hamid, F M [Radioisotope Department, Nuclear Research Center, Radiation Biology, cairo (Egypt); Roushdy, H M [Department, National Center for Radiation Reasrch and Technology, Cairo (Egypt); Girgis, R B; Abu-Ghadir, A R [Atomic Energy Authority, and Zoology Department, Faculty of Science, Cairo University, Cairo (Egypt)

1995-10-01

Male albino rats were exposed to gamma irradiation alone or after either oral daily administration of 50 or 100 mg kelthane for 3 successive days; or daily administration of 200 mg kelthane mixed with food per kg body weight for 3,6 and 12 weeks. Relative spleen weight and certain hematological values were determined. Significant decrease could be estimated in relative spleen weight due to exposure only to gamma irradiation significant increase was recorded due to treatment with 50 and 100 mg kelthane. The data obtained on hematological levels revealed insignificant changes in erythrocyte counts and hemoglobin concentration due to exposure to gamma irradiation and/.or kelthane treatment. Significant decrease was recorded in hematocrit value either for successive 30 days or due exposure to gamma irradiation after treatment with kelthane for short and long term periods. Leucocyte counts showed significant decrease for all animals groups. 2 tabs.

fluctuation in hematology values in gamma irradiated rats subjected to pesticide ingestion

International Nuclear Information System (INIS)

abdel-Hamid, F.M.; Roushdy, H.M.; Girgis, R.B.; Abu-Ghadir, A.R.

1995-01-01

Male albino rats were exposed to gamma irradiation alone or after either oral daily administration of 50 or 100 mg kelthane for 3 successive days; or daily administration of 200 mg kelthane mixed with food per kg body weight for 3,6 and 12 weeks. Relative spleen weight and certain hematological values were determined. Significant decrease could be estimated in relative spleen weight due to exposure only to gamma irradiation significant increase was recorded due to treatment with 50 and 100 mg kelthane. The data obtained on hematological levels revealed insignificant changes in erythrocyte counts and hemoglobin concentration due to exposure to gamma irradiation and/.or kelthane treatment. Significant decrease was recorded in hematocrit value either for successive 30 days or due exposure to gamma irradiation after treatment with kelthane for short and long term periods. Leucocyte counts showed significant decrease for all animals groups. 2 tabs

Feasibility of LED-Assisted CMOS Camera: Contrast Estimation for Laser Tattoo Treatment

Directory of Open Access Journals (Sweden)

Ngot Thi Pham

2018-04-01

Full Text Available Understanding the residual tattoo ink in skin after laser treatment is often critical for achieving good clinical outcomes. The current study aims to investigate the feasibility of a light-emitting diode (LED-assisted CMOS camera to estimate the relative variations in tattoo contrast after the laser treatment. Asian mice were tattooed using two color inks (black and red. The LED illumination was a separate process from the laser tattoo treatment. Images of the ink tattoos in skin were acquired under the irradiation of three different LED colors (red, green, and blue for pre- and post-treatment. The degree of contrast variation due to the treatment was calculated and compared with the residual tattoo distribution in the skin. The black tattoo demonstrated that the contrast consistently decreased after the laser treatment for all LED colors. However, the red tattoo showed that the red LED yielded an insignificant contrast whereas the green and blue LEDs induced a 30% (p < 0.001 and 26% (p < 0.01 contrast reduction between the treatment conditions, respectively. The proposed LED-assisted CMOS camera can estimate the relative variations in the image contrast before and after the laser tattoo treatment.

Effect of the laser and light-emitting diode (LED) phototherapy on midpalatal suture bone formation after rapid maxilla expansion: a Raman spectroscopy analysis.

Science.gov (United States)

Rosa, Cristiane Becher; Habib, Fernando Antonio Lima; de Araújo, Telma Martins; Aragão, Juliana Silveira; Gomes, Rafael Soares; Barbosa, Artur Felipe Santos; Silveira, Landulfo; Pinheiro, Antonio L B

2014-05-01

The aim of this study was to analyze the effect of laser or light-emitting diode (LED) phototherapy on the bone formation at the midpalatal suture after rapid maxilla expansion. Twenty young adult male rats were divided into four groups with 8 days of experimental time: group 1, no treatment; group 2, expansion; group 3, expansion and laser irradiation; and group 4, expansion and LED irradiation. In groups 3 and 4, light irradiation was in the first, third, and fifth experimental days. In all groups, the expansion was accomplished with a helicoid 0.020" stainless steel orthodontic spring. A diode laser (λ780 nm, 70 mW, spot of 0.04 cm(2), t = 257 s, spatial average energy fluence (SAEF) of 18 J/cm(2)) or a LED (λ850 nm, 150 mW ± 10 mW, spot of 0.5 cm(2), t = 120 s, SAEF of 18 J/cm(2)) were used. The samples were analyzed by Raman spectroscopy carried out at midpalatal suture and at the cortical area close to the suture. Two Raman shifts were analyzed: ∼ 960 (phosphate hydroxyapatite) and ∼ 1,450 cm(-1) (lipids and protein). Data was submitted to statistical analysis. Significant statistical difference (p ≤ 0.05) was found in the hydroxyapatite (CHA) peaks among the expansion group and the expansion and laser or LED groups. The LED group presented higher mean peak values of CHA. No statistical differences were found between the treated groups as for collagen deposition, although LED also presented higher mean peak values. The results of this study using Raman spectral analysis indicate that laser and LED light irradiation improves deposition of CHA in the midpalatal suture after orthopedic expansion.

RPV-1: A Virtual Test Reactor to simulate irradiation effects in light water reactor pressure vessel steels

International Nuclear Information System (INIS)

Jumel, Stephanie; Van-Duysen, Jean Claude

2005-01-01

Many key components in commercial nuclear reactors are subject to neutron irradiation which modifies their mechanical properties. So far, the prediction of the in-service behavior and the lifetime of these components has required irradiations in so-called 'Experimental Test Reactors'. This predominantly empirical approach can now be supplemented by the development of physically based computer tools to simulate irradiation effects numerically. The devising of such tools, also called Virtual Test Reactors (VTRs), started in the framework of the REVE Project (REactor for Virtual Experiments). This project is a joint effort among Europe, the United States and Japan aimed at building VTRs able to simulate irradiation effects in pressure vessel steels and internal structures of LWRs. The European team has already built a first VTR, called RPV-1, devised for pressure vessel steels. Its inputs and outputs are similar to those of experimental irradiation programs carried out to assess the in-service behavior of reactor pressure vessels. RPV-1 is made of five codes and two databases which are linked up so as to receive, treat and/or convey data. A user friendly Python interface eases the running of the simulations and the visualization of the results. RPV-1 is sensitive to its inputs (neutron spectrum, temperature, ...) and provides results in conformity with experimental ones. The iterative improvement of RPV-1 has been started by the comparison of simulation results with the database of the IVAR experimental program led by the University of California Santa Barbara. These first successes led 40 European organizations to start developing RPV-2, an advanced version of RPV-1, as well as INTERN-1, a VTR devised to simulate irradiation effects in stainless steels, in a large effort (the PERFECT project) supported by the European Commission in the framework of the 6th Framework Program

Estimation of damage by inmates of a PWR Reactor neutron irradiation. Project ZIRP; Estimacion del Dano por Irradiacion Neutronica en los Internos de un Reactor PWR. Proyecto ZIRP

Energy Technology Data Exchange (ETDEWEB)

Cadenas Mendicoa, A. M.

2013-07-01

The study presented here focuses on the analysis of neutron and gamma irradiation damage suffered by the inmates of the JC NPP reactor metallic materials throughout its operational life. Such analysis of radiation are part of a project of great international impact, led by EPRI (Electric Power Research Institute) from the MRP (Materials Reliability Program), which aims to relate the degradation of the properties of metallic materials of the inmates of the reactor, with the conditions of operation and irradiation to which have been subjected during the operational life of the plant.

Path dependent models to predict property changes in graphite irradiated at changing irradiation temperatures

CSIR Research Space (South Africa)

Kok, S

2010-10-01

Full Text Available Property changes occur in materials subjected to irradiation. The bulk of experimental data and associated empirical models are for isothermal irradiation. The form that these isothermal models take is usually closed form expressions in terms...

A new LED lamp for the collection of nocturnal Lepidoptera and a spectral comparison of light-trapping lamps

Directory of Open Access Journals (Sweden)

Gunnar Brehm

2017-04-01

Full Text Available Most nocturnal Lepidoptera can be attracted to artificial light sources, particularly to those that emit a high proportion of ultraviolet radiation. Here, I describe a newly developed LED lamp set for the use in the field that is lightweight, handy, robust, and energy efficient. The emitted electromagnetic spectrum corresponds to the peak sensitivity in most Lepidoptera eye receptors (ultraviolet, blue and green. Power LEDs with peaks at 368 nm (ultraviolet, 450 nm (blue, 530 nm (green, and 550 nm (cool white are used. I compared the irradiance (Ee of many commonly used light-trapping lamps at a distance of 50 cm. Between wavelengths of 300 and 1000 nm, irradiance from the new lamp was 1.43 W m-2. The new lamp proved to be the most energy efficient, and it emitted more radiation in the range between 300 and 400 nm than any other lamp tested. Cold cathodes are the second most energy-efficient lamps. Irradiation from fluorescent actinic tubes is higher than from fluorescent blacklight-blue tubes. High-wattage incandescent lamps and self-ballasted mercury vapour lamps have highest irradiance, but they mainly emit in the long wave spectrum. The use of gauze and sheets decreases the proportion of UV radiation and increases the share of blue light, probably due to optical brighteners. Compared with sunlight, UV irradiance is low at a distance of 50 cm from the lamp, but (safety glasses as well as keeping sufficient distance from the lamp are recommended. In field tests, the new LED lamp attracted large numbers of Lepidoptera in both the Italian Alps and in the Peruvian Andes.

Electron irradiation of dry food products

Energy Technology Data Exchange (ETDEWEB)

Gruenewald, Th [Bundesbahn-Zentralamt, Minden (Germany, F.R.)

1983-01-01

The interest of the industrial food producer is increasing in having the irradiation facility installed in the food processing chain. The throughput of the irradiator should be high and the residence time of the product in the facility should be short. These conditions can be accomplished by electron irradiators. To clarify the irradiation conditions spices taken out of the industrial process, food grade salt, sugar, and gums as models of dry food products were irradiated. With a radiation dose of 10 kGy microbial load can be reduced on 10**4 microorganisms/g. The sensory properties of the spices were not changed in an atypical way. For food grade salt and sugar changes of colour were observed which are due to lattice defects or initiated browning. The irradiation of several gums led only in some cases to an improvement of the thickness properties in the application below 50 deg C, in most cases the thickness effect was reduced. The products were packaged before irradiation. But it would be possible also to irradiate the products without packaging moving the product through the irradiation field in a closed conveyor system.

Electron irradiation of dry food products

International Nuclear Information System (INIS)

Gruenewald, Th.

1983-01-01

The interest of the industrial food producer is increasing in having the irradiation facility installed in the food processing chain. The throughput of the irradiator should be high and the residence time of the product in the facility should be short. These conditions can be accomplished by electron irradiators. To clarify the irradiation conditions spices taken out of the industrial process, food grade salt, sugar, and gums as models of dry food products were irradiated. With a radiation dose of 10 kGy microbial load can be reduced on 10**4 microorganisms/g. The sensory properties of the spices were not changed in an atypical way. For food grade salt and sugar changes of colour were observed which are due to lattice defects or initiated browning. The irradiation of several gums led only in some cases to an improvement of the thickness properties in the application below 50 deg C, in most cases the thickness effect was reduced. The products were packaged before irradiation. But it would be possible also to irradiate the products without packaging moving the product through the irradiation field in a closed conveyor system. (author)

Electromechanical engineering aspects of irradiator design

International Nuclear Information System (INIS)

Etienne, J.C.; Buyle, R.

1984-01-01

IRE, Institut National des Radioelements at Fleurus, has been irradiating foodstuffs since 1979. The steadily-increasing demands of the food industry led IRE to design and install a second, different type of irradiator. Selection criteria for choosing between the different alternatives or possibilities are given based on the primary consideration that a contract food irradiator must be able to provide a service in accordance with the requirements of his customers. The principal components - the radiation source geometry, the transport system and the control systems - are described. The choice of the major electromechanical components is discussed taking into account their susceptibility to radiation damage. (author)

Photobiomodulation for Cobalt Chloride-Induced Hypoxic Damage of RF/6A Cells by 670 nm Light-Emitting Diode Irradiation

Directory of Open Access Journals (Sweden)

Shuang Li

2014-01-01

Full Text Available Objective. The goal of this study was to investigate the therapeutic efficacy of 670 nm light-emitting diode (LED irradiation on the diabetic retinopathy (DR using hypoxic rhesus monkey choroid-retinal (RF/6A cells as the model system. Background Data. Treatment with light in the spectrum from red to near-infrared region has beneficial effect on tissue injury and 670 nm LED is currently under clinical investigation for retinoprotective therapy. Methods. Studies were conducted in the cultured cells under hypoxia treated by cobalt chloride (CoCl2. After irradiation by 670 nm LED with different power densities, cell viability, cytochrome C oxidase activity, and ATP concentration were measured. Results. The irradiation of 670 nm LED significantly improved cell viability, cytochrome C oxidase activity, and ATP concentration in the hypoxia RF/6A cells. Conclusion. 670 nm LED irradiation could recover the hypoxia damage caused by CoCl2. Photobiomodulation of 670 nm LED plays a potential role for the treatment of diabetic retinopathy.

The effect of X-ray irradiation on changes of blood chemistry in RC-MAP and CPD-whole blood after irradiation

International Nuclear Information System (INIS)

Hirose, Tetsuhito; Katayama, Norihumi; Okamoto, Yukiharu; Tsuda, Tadaaki; Ota, Kiichiro; Nishioka, Shingo; Tsumura, Michiyo

1997-01-01

The Japanese Welfare Ministry recommended to irradiate transfused blood in order to inactivate lymphocytes, thereby preventing from transfusion associated graft-versus-host disease (PT-GVHD). But an adequate dose of irradiation applied to various kinds of transfused blood has not yet known. We investigated the effect of a irradiation dose of 15 Gy (gray) on changes of plasma K, GOT, BUN and total protein (T.P) in RC-MAP (MAP) and CPD added whole blood (CPD) after days of storage of irradiation. There was a significant increase of potassium (K) in plasma in irradiated RC-MAP, compared with those in non-irradiated RC-MAP, after storage from day 2. Plasma K level in irradiated CPD increased more than those in non-irradiated CPD after storage at day 5. No different increases in plasma GOT, BUN and T.P levels were not shown in irradiated RC-MAP and CPD. Our data led to a conclusion that a adequate irradiated dose seemed to be different in various kinds of transfused blood to inactivate lymphocyte for the prevention of PT-GVHD. (author)

DAMAGE IN MOLYBDENUM ASSOCIATED WITH NEUTRON IRRADIATION AND SUBSEQUENT POST-IRRADIATION ANNEALING

Energy Technology Data Exchange (ETDEWEB)

Mastel, B.

1963-07-23

Molybdemum containing carbon was studied in an attempt to establish the combined effect of impurity content and neutron irradiation on the properties and structure of specific metals. Molybdenum foils were punched into discs and heat treated in vacuum. They were then slow-cooled and irradiated. After irradiation and subsequent decay of radioactivity to a low level the foils were subjected to x-ray diffraction measurements. Cold-worked foils with less than 10 ppm carbon showed no change in microstructure due to irradiation. Molybdenum foils that were annealed prior to irradiation showed spot defects. In foils containing up to 500 ppm carbon, it was concluded that the small loops present after irradiation are due to the clustering of point defects at interstitial carbon atoms, followed by collapse to form a dislocation loop. The amount of lattice expansion after irradiation was strongly dependent on impurity content. Neutron irradiation was found to reduce the number of active slip systems. (M.C.G.)

Photocatalytic decomposition of selected estrogens and their estrogenic activity by UV-LED irradiated TiO_2 immobilized on porous titanium sheets via thermal-chemical oxidation

International Nuclear Information System (INIS)

Arlos, Maricor J.; Liang, Robert; Hatat-Fraile, Melisa M.; Bragg, Leslie M.; Zhou, Norman Y.; Servos, Mark R.; Andrews, Susan A.

2016-01-01

Highlights: • TiO_2 self-assembled on oxidized porous titanium sheets. • UV-LED/TiO_2 membrane treatment reduced the concentrations of estrogens. • Different pH conditions affect treatment efficiency. • The estrogenic activity removal was similar to the chemical disappearance. - Abstract: The removal of endocrine disrupting compounds (EDCs) remains a big challenge in water treatment. Risks associated with these compounds are not clearly defined and it is important that the water industry has additional options to increase the resiliency of water treatment systems. Titanium dioxide (TiO_2) has potential applications for the removal of EDCs from water. TiO_2 has been immobilized on supports using a variety of synthesis methods to increase its feasibility for water treatment. In this study, we immobilized TiO_2 through the thermal-chemical oxidation of porous titania sheets. The efficiency of the material to degrade target EDCs under UV-LED irradiation was examined under a wide range of pH conditions. A yeast-estrogen screen assay was used to complement chemical analysis in assessing removal efficiency. All compounds but 17β-estradiol were degraded and followed a pseudo first-order kinetics at all pH conditions tested, with pH 4 and pH 11 showing the most and the least efficient treatments respectively. In addition, the total estrogenic activity was substantially reduced even with the inefficient degradation of 17β-estradiol. Additional studies will be required to optimize different treatment conditions, UV-LED configurations, and membrane fouling mitigation measures to make this technology a more viable option for water treatment.

Types and three-dimensional distribution of neuronal ectopias in the brain of mice prenatally subjected to X-irradiation

Energy Technology Data Exchange (ETDEWEB)

Sun, Xue-Zhi; Takahashi, Sentaro; Kubota, Yoshihisa; Sato, Hiroshi [National Inst. of Radiological Sciences, Chiba (Japan); Cui, Chun; Fukui, Yoshihiro [Tokushima Univ. (Japan). School of Medicine; Inouye, Minoru [Shin Nippon Biomedical Lab., Ltd., Miyanoura, Kagoshima (Japan)

2002-03-01

The types and three-dimensional distribution of neocortical ectopias following prenatal exposure to X-irradiation were studied by a histological examination and computer reconstruction techniques. Pregnant ICR mice were subjected to X-irradiation at a dose of 1.5 Gy on embryonic day 13. The brains from 30-day-old mice were serially sectioned on the frontal plane at 15 {mu}m, stained with HE and observed with a microscope. The image data for the sections were input to a computer, and then reconstructed to three-dimensional brain structures using the Magellan 3.6 program. Sectional images were then drawn on a computer display at 240 {mu}m intervals, and the positions of the different types of neocortical ectopias were marked using color coding. Three types of neocortical ectopias were recognized in the irradiated brains. Neocortical Lay I ectopias were identified as small patches in the caudal occipital cortex, and were located more laterally in the neocortex in caudal sections than in the rostral sections. Periventricular ectopias were located more rostrally than Lay I ectopias, and were found from the most caudal extent of the presumed motor cortex to the most caudal extent of the lateral ventricle. Hippocampal ectopias appeared as continuous linear bands, and were frequently associated with the anterior parts of the periventricular ectopias. (author)

Detection of Certain Spices Subjected to Gamma Irradiation By Using Thermal Analysis Technique

International Nuclear Information System (INIS)

Sayed, M.S.; Ali, H.G.M.; Abdeldaiem, M.H.

2013-01-01

The present investigation was carried out to apply a detection method of some irradiated spices using thermal analysis technique. Black pepper, cumin and ginger were irradiated using gamma irradiation at dose levels 5, 10 and 15 kGy and stored for 12 months at room temperature. Thermal analysis techniques TGA and DTA were studied for characterizing irradiated spices. Thermo gravimetric analysis (TGA) is a method where the measurement of mass as a function of heating is recorded. TGA was used to determine the moisture and ash contents and thermal stabilities. Non-significant changes of the weight loss percent due to the irradiation were occurred on the studied spices up to 10 kGy. The weight loss was decreased at the first step up to 100 degree C due to the release of water of hydration. Another sharp decreasing in weight loss percent at the second step 220-300 degree C may be due to volatilization of the sample. The final weight loss weight loss stage up to 500 degree C may be due to burn out the fixed carbon remaining in the sample. As the irradiation dose increased from control up to 15 kGy, the weight loss percent at the dehydration step was decreased. The kinetics of the spices decomposition were studied in order to ascertain the type of weight loss mechanism and calculate the activation energy (E a ). The differential thermal analysis (DTA) of the studied samples showed two main characteristic peaks; endothermic one due to the dehydration process and the second peak may be due to the partial volatilization of the aromatic compounds of the main constituent of the studied spices. It could be concluded that using gamma irradiation (up to 15.0 kGy) for black pepper, cumin and ginger are thermally stable to human consumption.

Alterations in tissue lipids of rats subjected to whole-body X-irradiation

Energy Technology Data Exchange (ETDEWEB)

De, A K; Aiyar, A S [Bhabha Atomic Research Centre, Bombay (India). Biochemistry and Food Technology Div.

1978-02-01

Whole-body irradiation of rats at sublethal doses leads to hepatic lipid accumulation which reaches a maximum by the sixth day; this effect on lipid metabolism does not appear to be due to accompanying inanition but due to irradiation per se. The female rats show a greater and more consistent increase in liver lipids than males and this better response of the females is not abolished by prolonged administration of testosterone to these animals. An accumulation of triglycerides accounts for almost all the increases in total liver lipids, although smaller elevations in the levels of free fatty acids and cholesterol are also seen. Free fatty acids of liver show a marked decrease on the second day following irradiation. Serum lipids do not show any appreciable changes while adipose lipids progressively decrease reaching a minimum by the sixth day. Although an insufficiency of ATP may be responsible for lipid accumulation in the irradiated rat as in the case in rats treated with ethionine or orotic acid, adenine administration, which prevents fatty infiltration due to these chemical agents, does not protect against the radiation-induced increase in liver triglycerides.

Chemical changes in food packaging resulting from ionizing irradiation

International Nuclear Information System (INIS)

Thayer, D.W.

1988-01-01

Recent approvals of food irradiation processes by the U.S. Food and Drug Administration have led to a search for packaging approved for use with ionizing radiation. Though 13 packaging materials were approved several years ago as food contactants for gamma irradiation up to 10 kGy at refrigeration temperatures and 4 packaging materials were approved for up to 60 kGy at cryogenic temperatures, no currently used packaging is approved for irradiated foods. Extensive research was conducted by the U.S. Army and others on the suitability of both flexible packaging and metal cans for packaging irradiated foods. The results of the studies of packaging for irradiated foods will be described and discussed in context of currently used packaging materials for non-irradiated meats and poultry

The influence of gamma irradiation on natural dyeing properties of cotton and flax fabrics

Science.gov (United States)

Chirila, Laura; Popescu, Alina; Cutrubinis, Mihalis; Stanculescu, Ioana; Moise, Valentin Ioan

2018-04-01

Fabrics made of 100% cotton and 100% flax respectively were exposed at ambient temperature to gamma radiation doses, from 5 to 40 kGy, using a Co-60 research irradiator. After the irradiation treatment the fabrics were subjected to dyeing process with Itodye Nat Pomegranate commercial natural dye. The influence of gamma irradiation treatment on the physical-mechanical properties, dyeing and surface morphology of natural fibres were investigated. Gamma ray treatment of 40 kGy was the most effective in the case of fabrics made from 100% cotton, enhancing the colour strength as evidenced by K/S value. The results obtained from the mechanical properties of fabrics made of 100% flax indicated that the dose of 40 kGy leads to a decrease of tensile strength up of to 41.5%. Infrared spectroscopy was used to monitor chemical and structural changes in cellulosic fibres induced during processing. Crystallinity indices calculated from various bands ratio showed insignificant variations for cotton and small variations in the case of flax. The surface morphology of irradiated cotton fabrics did not show significant changes even at the highest dose of 40 kGy, while the low doses applied on flax fabrics led to an appearance of small changes of surface morphology. The gamma irradiation increased the uptake of natural dyes on natural cellulosic fibres.

Food irradiation and consumer values

International Nuclear Information System (INIS)

Bruhn, C.M.; Schutz, H.G.; Sommer, R.

1988-01-01

A mail survey technique was used to determine if value hierarchy, locus of control, innovativeness, and demographic parameters could distinguish between subjects expressing different levels of concern and willingness to buy irradiated food. Concern toward irradiated food was lower than concern for other food safety issues, probably because many expressed uncertainty regarding irradiation. Those ranking the value “an ecologically balanced world” expressed the greatest irradiation concern. Factors which could predict high irradiation concern were being highly concerned about the use of chemical sprays on food, completing more formal education and being female; those believing that life was controlled by luck were less concerned. Irradiation concern was a principal factor determining willingness to buy irradiated foods. Innovative consumers were more likely to try irradiated foods than noninnovative. Implications for consumer education are presented

The radiation hardness of silica optical fiber used in the LED-fiber monitor of BLM and BESIII EMC

International Nuclear Information System (INIS)

Xue Zhen; Hu Tao; Fang Jian; Xu Zizong; Wang Xiaolian; Lü Junguang; Zhou Li; Cai Xiao; Yu Boxiang; Wang Zhigang; Sun Lijun; Sun Xilei; Zhang Aiwu

2012-01-01

LED-fiber system has been used to monitor BLM and BESIII EMC. A radiation hard silica optical fiber is essential for its stability and reliability. Three types of silica optical fibers, silicone-clad silica optical fiber with high OH - content (SeCS), silica-clad silica optical fiber with low OH - content (SCSL) and silica-clad silica opical fiber with high OH - content (SCSH) were studied. In the experiment, 12 groups of fiber samples were irradiated by 60 Co and 3 groups of fiber samples were irradiated by BEPCII background radiation. Radiation hardness: the radiation hardness of SCSH is best and meets the radiation hardness requirement for LED-fiber monitor of BLM and BESIII EMC. The transmission of SeCS and SCSH decreased to around 80% under the 60 Co-irradiation of 5 Gy and 10 Gy, respectively. The radiation hardness of SeCS is worst because of its silicone cladding. Recovery characteristics: 60 Co-irradiated by the same doses, there were both more annealable and more permanent color centers formed in SeCS than SCSL, and for the same kind of fibers, as long as the irradiated doses are under a certain amount (for example, less than 5 Gy for SeCS), the higher the doses, both the more annealable and the more permanent color centers are formed.

A review of the studies on the wholesomeness of irradiated wheat, conducted at the National Institute of Nutrition, India

International Nuclear Information System (INIS)

Vijayalaxmi; Srikantia, S.G.; Mysore Univ. Coll.

1989-01-01

The wholesomeness of irradiated wheat was investigated in a series of experiments involving several species of animals and a small number of children, at the National Institute of Nutrition in India. Our observations indicated some effects following the feeding of freshly irradiated wheat while no such changes were found in the groups fed either unirradiated or stored irradiated wheat. Also, there were no significant differences between the groups fed unirradiated and stored irradiated wheat. Based on these results, a recommendation had been made to the government that when subjected to irradiation, wheat should be stored for at least 3 months before considering it as safe for human consumption. Similar experiments conducted in an establishment of the Department of Atomic Energy in India indicated no undesirable effects, unlike those found in our studies, and this had led to the development of a serious controversy. In this paper, we have not only reviewed our studies in the light of subsequent research independently carried out in other laboratories but also have tried to answer some of the criticisms made against our studies, so that some of the misunderstandings of our work are seen in proper perspective. (author)

Irradiation and Post-Irradiation Storage of Chicken: Effects on Fat and Proteins

International Nuclear Information System (INIS)

Abou-Tarboush, H.M.; Al-Kahtani, H.A.; Abou-Arab, A.A.; Atia, M.; Bajaber, A.S.; Ahmed, M.A.; El-Mojaddidi, M.A.

1997-01-01

Chicken were subjected to gamma irradiation doses of 2.5, 5.0, 7.5 and 10.0 KGy and post-irradiation storage of 21 days at 4±2º. The effects on fat and protein of chicken were studied. Rate of formation of total volatile basic-nitrogen was less in irradiated samples particularly in samples treated with 5.0KGy during the entire storage. Fatty acid profiles of chicken lipids were not significantly (P≤ 0.05) affected by irradiation especially at doses of 5.0 KGy. However, irradiation caused a large increase in thiobarbituric acid (TBA) values which continued gradually during storage. Changes in amino acids were minimal. Irradiated and unirradiated samples showed the appearance of protein subunits with molecular weights in the range of 10.0 to 88.0 and 10.0 to 67.0 KD, respectively. No changes were observed in the sarcoplasmic protein but the intensity of bands in all irradiated samples decreased after 21 days of storage

Determination of bacterial endotoxins in blood of animals and humans subjected to irradiation

Energy Technology Data Exchange (ETDEWEB)

Kiselev, P N; Shchul' s, T S [Tsentral' nyj Nauchno-Issledovatel' skij Rentgeno-Radiologicheskij Inst., Leningrad (USSR)

1981-01-01

The content of Gram-negative bacterium endotoxins in the irradiated organism was determined by the use of actinomycin D sensitizing the organism to the effect of such toxins. Regularities in the accumulation of Gram-negative bacterium endotoxins in the irradiated organism were studied as well as the dependence of animal sensitization on the actinomycin D dose. Possibilities for the development of endotoxemia in oncologic patients in the process of radiotheraphy were traced. It is shown that the radiotherapy of the intestine containing large quantaties of bacteria and their toxins is accompanied by endotoxemia; in the first part of the radiotherapy course its manifestation depends on the irradiation dose; having reached a specific level, endotoxemia retains its symptoms till the end of irradiation. It is indicated that the determination of bacterium endotoxins is of interest when studying not only the development of endotoxemia in the organism exposed to radiation, hut also many other toxemic states.

Identification of dehydrated spices and herbs subjected to the irradiation process

International Nuclear Information System (INIS)

Bernardes, Dulcila Maria Lessa

1996-01-01

This research shows the possibility of determining through a combination of analytical methods whether dehydrated spices and herbs were irradiated. The methods used were the following: viscosimetry, thermoluminescence (TL) and electron paramagnetic resonance (EPR). Viscosimetry was applied in suspensions of dehydrated and irradiated spices and herbs which had been gellified by heat. It was observed that the viscosity of the samples decreases when the radiation dose increases. It was also observed that the temperature of the gelification is linked to the viscosity. The variation of the capability of gelification of the samples in relation to the storage time (30 and 60 days) does not have any consequence on the viscosity. Thermoluminescence is based on the transference of electrons to an excited state by ionizing radiation with emission of light when the electrons thermally stimulated. The thermoluminescent signals of the spices can be explained by the presence of mineral grains adhering to the surface of the samples. The thermoluminescent signal increased in intensity with the amplification of the radiation dose. The study of the signal in relation to the storage time (30 and 60 days) showed that it weakened and decreased. Free radicals produced by irradiation of spices were analyzed by the electron spin resonance method (ESR). It was checked that increasing the radiation dose meant an intensification of the ESR signal. Within a 30 day storage time, a fading of the signal was observed. The results of this study lead us to the following conclusion: viscosimetry, thermoluminescence and electron spin resonance are methods of analysis which are proper to detect whether dehydrated spices and herbs were irradiated, especially when these different methods were used in combination. (author)

Evaluation of the effect of LED radiation in the repair of skin wounds on the dorsum of rats with iron deficiency anemia

Science.gov (United States)

de Oliveira, Susana Carla Pires Sampaio; de Carvalho Monteiro, Juliana Santos; dos Santos Aciole, Gilberth Tadeu; DeCastro, Isabele Cardoso V.; Menezes, Diego Silva; de Fátima Lima Ferreira, Maria; dos Santos, Jean Nunes; Zanin, Fátima; Barbosa Pinheiro, Antônio Luiz

2010-05-01

Iron deficiency anemia causes reduction on the level of hemoglobin and of the number of RBC and affects around 35% of the human population. Laser and LED therapies have been successfully used on wound healing studies. The aim of the present study was to assess histologically the effect of LED Phototherapy on the healing of cutaneous wounds on anemic rats. Fifty one 21 days old male wistar rats weighting around 50 g were kept under iron free die (Sem ferro-AIN93-G) during 15 days in order to induce anemia. Non treated animals acted as controls. A standartized cutaneous wound was created on the dorsum of each animal whom were distributed into four groups: Group I—Anemia+LED, Group II—Non anemic+LED, Group III—Anemia+no treatment, Group IV—No anemic+no-treatment. Irradiation started immediately after surgery and repeated at 48 h intervals during 21 days. Animal death occurred after 7, 14 and 21 days after wounding. The results of the histologic analysis showed that LED Phototherapy stimulated fibroblastic proliferation. It is concluded that LED irradiation improves wound healing on iron deficient anemic animals.

THE PHOTODYNAMIC EFFECT OF LED-MAGNETIC EXPOSURE TO PHOTOINACTIVATION OF AEROBIC PHOTOSYNTETIC BACTERIA

Directory of Open Access Journals (Sweden)

Suryani Dyah Astuti

2014-01-01

Full Text Available All photosynthetic bacteria have a major pigment of bacteriochlorophyl and accessor pigment e.g. the carotenoids, which both have an important role in photosynthesis process. This study aim to explore the exogenous organic photosensitizer from photosyntetic bacteria for photodynamic therapy application. This study is an experimental research aiming to test the potential illumination ofLED with wavelength 409, 430, 528 and 629 nm, and power optimization and time exposure LED-magnetic for optimum photo activation Rhodococcus growth. The reseach design use a factorial completely randomized design with factor ofpower and exposure time. The number ofbacterial colonies grown measure using ofTotal Plate Count (TPC methods. The result ofanova test shows that irradiation treatment with LED 409 nm, 430 nm, 528 nm and 629 nm significantly affects on bacterial colony growth. LED 409 nm exposure has the greatest potential to boost the growth ofbacterial colonies by 77%. LED exposure and the addition of1.8 mT magnetic field increases bacterial colony growth by 98%. Results of optimization of LED and magnetic fields show power 46 mW and a 40 minute (energy dose 110 J/cm2 optimum growth ofbacterial colonies increase by 184%. So LED and magnetic illumination has potentially increased the viability ofan aerob photosyntetic bacteria colonies.

Testing of Performance of Optical Fibers Under Irradiation in Intense Radiation Fields, When Subjected to High Temperature

International Nuclear Information System (INIS)

Blue, Thomas; Windl, Wolfgang; Dickerson, Bryan

2013-01-01

The primary objective of this project is to measure and model the performance of optical fibers in intense radiation fields when subjected to very high temperatures. This research will pave the way for fiber optic and optically based sensors under conditions expected in future high-temperature gas-cooled reactors. Sensor life and signal-to-noise ratios are susceptible to attenuation of the light signal due to scattering and absorbance in the fibers. This project will provide an experimental and theoretical study of the darkening of optical fibers in high-radiation and high-temperature environments. Although optical fibers have been studied for moderate radiation fluence and flux levels, the results of irradiation at very high temperatures have not been published for extended in-core exposures. Several previous multi-scale modeling efforts have studied irradiation effects on the mechanical properties of materials. However, model-based prediction of irradiation-induced changes in silica'@@s optical transport properties has only recently started to receive attention due to possible applications as optical transmission components in fusion reactors. Nearly all damage-modeling studies have been performed in the molecular-dynamics domain, limited to very short times and small systems. Extended-time modeling, however, is crucial to predicting the long-term effects of irradiation at high temperatures, since the experimental testing may not encompass the displacement rate that the fibers will encounter if they are deployed in the VHTR. The project team will pursue such extended-time modeling, including the effects of the ambient and recrystallization. The process will be based on kinetic MC modeling using the concept of amorphous material consisting of building blocks of defect-pairs or clusters, which has been successfully applied to kinetic modeling in amorphized and recrystallized silicon. Using this procedure, the team will model compensation for rate effects, and

Fluctuation in haematological values in gamma irradiated rats subjected to pesticide ingestion

International Nuclear Information System (INIS)

Abdel-Hamid, F.M.; Roushdy, H.M.; Abu-Ghadeer, A.R.; Girgis, R.B.

1995-01-01

Male albino rats were exposed to gamma irradiation alone or after either oral daily administration of 50 or 100 mg kelthane for 3 successive days; or daily administration of 200 mg kelthane mixed with food per kg body weight for 3,6 and 12 weeks. Relative spleen weight and certain hematological values were determined. Significant decrease could be estimated in relative spleen weight due to exposure to gamma irradiation. Significant increase was recorded due to treatment with 50 and 100 mg kelthane. The data obtained on hematological levels revealed insignificant changes in erythrocyte counts and hemoglobin concentration due to exposure to gamma irradiation and / or kelthane treatment. Significant decrease was recorded in hematocrit value either for successive 30 days or due to exposure to gamma radiation after treatment with kelthane for short and long term periods. Leucocyte counts showed significant decrease for all animal groups. 2 tabs

Effect of neutron irradiation on vitreous carbon

International Nuclear Information System (INIS)

Kurolenkin, E.I.; Virgil'ev, Yu.S.; Chugunova, T.K.

1989-01-01

The change in mass (m), volume (V), specific electric resistance (ρ), coefficient of linear thermal expansion (α), dynamic elasticity modulus (E), and limit of bending strength (σ) of vitreous carbon are studied upon neutron irradiation. Samples for study were two forms of vitreous carbon obtained by hardening thermally reactive polymers at 900-1,000 degree K. Phenol-formaldehyde (bakelite lacquer A, Bakelite A) and furfural-phenol-formaldehyde (FM-2) resin were used. They were irradiated in the experimental water - water VVR-M reactor between 360-1,030 degree K. The maximal neutron flux was 1.65·10 21 neut/cm 2 . Neutron irradiation of vitreous carbon led to its shrinkage and accompanied weakening. Shrinkage and weakening of vitreous carbon was decreased with an increase of treatment and irradiation temperatures

Integrated studies of irradiated Philippine mangoes. Part of coordinated programme in Asian Regional Cooperative Project on Food Irradiation

International Nuclear Information System (INIS)

Manalo, J.A.

1985-09-01

Effects of combined treatment of hot water dip (50 deg. C for 5 min.) and irradiation (0.65 kGy) on technological and sensory qualities of Carabao mangoes were investigated. Mangoes that ripen to the yellow green stage during transport may be subjected to irradiation of combined hot water dip at 50 deg. C for 5 minutes and irradiation at 0.65 kGy. When stored at the low temperature of 12-15 deg. C, shelf life is extended further. Time interval between hot water dip and irradiation must be as short as possible and fruits must be stored at ambient temperature prior to irradiation to prevent discoloration. Shelf life studies show that green fruits subjected to combined treatment and stored at ambient temperature extended shelf life by 6 days, 50% of yellow green mangoes subjected to combined treatment exhibited shelf life extension by four days. Mangoes stored at cold temperature, whether immediately after irradiation or after ripening showed considerable reduction in bacterial decay, regardless of fruit maturity, thus extending their shelf life considerably. Results of sensory evaluation showed no marked differences in color, aroma, appearance, and acceptability were observed by the taste panelists and although controls were always rated higher than the treated samples, scores higher than 5 given to the treated samples showed that they were also generally acceptable

Patient-led versus physician-led titration of insulin glargine in patients with uncontrolled type 2 diabetes: a randomized multinational ATLAS study.

Science.gov (United States)

Garg, Satish K; Admane, Karim; Freemantle, Nick; Odawara, Masato; Pan, Chang-Yu; Misra, Anoop; Jarek-Martynowa, Iwona R; Abbas-Raza, Syed; Mirasol, Roberto C; Perfetti, Riccardo

2015-02-01

Self-adjustment of insulin dose is commonly practiced in Western patients with type 2 diabetes but is usually not performed in Asian patients. This multinational, 24-week, randomized study compared patient-led with physician-led titration of once-daily insulin glargine in Asian patients with uncontrolled type 2 diabetes who were on 2 oral glucose-lowering agents. Patient-led (n = 275) or physician-led (n = 277) subjects followed the same dose-titration algorithm guided by self-monitored fasting blood glucose (FBG; target, 110 mg/dL [6.1 mmol/L]). The primary endpoint was change in mean glycated hemoglobin (HbA1c) at week 24 in the patient-led versus physician-led titration groups. Patient-led titration resulted in a significantly higher drop in HbA1c value at 24 weeks when compared with physician-led titration (-1.40% vs. -1.25%; mean difference, -0.15; 95% confidence interval, -0.29 to 0.00; P = .043). Mean decrease in FBG was greatest in the patient-led group (-2.85 mmol/L vs. -2.48 mmol/L; P = .001). The improvements in HbA1c and FBG were consistent across countries, with similar improvements in treatment satisfaction in both groups. Mean daily insulin dose was higher in the patient-led group (28.9 units vs. 22.2 units; Ptitration achieved near-target blood glucose levels in Asian patients with uncontrolled type 2 diabetes who were on 2 oral glucose-lowering drugs, demonstrating that Asian patients can self-uptitrate insulin dose effectively when guided.

Structure and Spatial Distribution of Ge Nanocrystals Subjected to Fast Neutron Irradiation

Directory of Open Access Journals (Sweden)

Alexander N. Ionov

2011-07-01

Full Text Available The influence of fast neutron irradiation on the structure and spatial distribution of Ge nanocrystals (NC embedded in an amorphous SiO2 matrix has been studied. The investigation was conducted by means of laser Raman Scattering (RS, High Resolution Transmission Electron Microscopy (HR-TEM and X-ray photoelectron spectroscopy (XPS. The irradiation of Ge- NC samples by a high dose of fast neutrons lead to a partial destruction of the nanocrystals. Full reconstruction of crystallinity was achieved after annealing the radiation damage at 8000C, which resulted in full restoration of the RS spectrum. HR-TEM images show, however, that the spatial distributions of Ge-NC changed as a result of irradiation and annealing. A sharp decrease in NC distribution towards the SiO2 surface has been observed. This was accompanied by XPS detection of Ge oxides and elemental Ge within both the surface and subsurface region.

Physical-chemical evaluation of wines subjected to gamma irradiation for aging

International Nuclear Information System (INIS)

Harder, Marcia N.C.; Perina, Vanessa C.S.; Silva, Lucia A.C.S.; Arthur, Valter; Franco, Camilo F.O.; Pires, Juliana A.; Scanholato, Mariana; Bortoleto, Gisele G.; Germek, Hermas A.

2011-01-01

Wine is a beverage made from the fermentation of sugars contained in grapes or grape juice, using yeast. Wines can be classified according to the amount of sugar they contain: dry, soft or sweet. Depending on the need for aging, they may be classified as young or aged. Modern methods of aging use gamma irradiation. There are several reasons for this type of procedure in wines, among them are: sterilization of the wort, changes in sensory characteristics of the wine, and accelerated aging. In this study, samples of soft red wine were obtained in the city of Sao Pedro in the local market, all bottles being of the same batch. The samples and the control were directly irradiated with gamma irradiation in polyethylene bags with doses of 1 KGy and 3 KGy, at a rate of 0.396 kGy/h. The evaluation parameters were tartaric acid, brix, pH, alcohol content and color. For statistical purposes, the Tukey test at 5% significance level was used. From the results obtained, it may be concluded that only the 3 KGy dose showed a statistically significant difference for the parameters shown, indicating that from this dose of radiation upwards there is a significant influence on the evaluation parameters. (author)

Safety evaluation on irradiated food ingestion

International Nuclear Information System (INIS)

1986-01-01

This paper reports double-blind observations of volunteers who took 35 kinds of irradiated foods as their main diet for 90 days. The subjects consisted of 70 medical students and 8 staff members in the Shanghai Medical University. They were randomly divided into two groups. One group was supplied with irradiated foods, the other acted as controls eating the same food but non-irradiated. The 35 kinds of irradiated foods were grain, meat products, vegetables, fruits, dried fruits etc. The absorbed dose of irradiation from the processed foods varied from 0.1 to 8.0 kGy. The irradiated foods made up 60.3% of the total food intake by weight. Observations during 90 days indicated that the subjects were all pleased with their diets and no adverse effects on their health were seen. Clinical and laboratory examinations included routine blood and urine tests, blood biochemical examinations, hepatic and renal function tests, endocrinological assays, cellular immunity tests, and mutagenetic studies (such as the incidence of polyploid cells, chromosomal structural aberration, rates of sister chromatid-exchanges, micronuclei test, urine Ames' test). These studies showed that the ingestion of these foods are safe for humans

Irradiation Detection in Korean Traditional Soybean-Based Fermented Powdered Sauces: Data for Establishing a Database for Regulation of Irradiated Foods

International Nuclear Information System (INIS)

Choi, I.D.; Kim, B.K.; Song, H.P.; Byun, M.W.; Kim, D.H.; Kim, M.C.; Lee, J.O.; Lee, H.J.

2005-01-01

To facilitate establishing regulations for irradiated foods, Korean traditional soybean-based fermented powdered doenjang (PD), kanjang (PK), kochujang (PKC) and chungkukjang (PC) were irradiated at 1, 3, 5 and 7 kGy, and subjected to irradiation detection analyses as part of establishing a database for detecting irradiated foods. Photostimulated luminescence (PSL) and electron spin resonance (ESR) were applied as the detection methods. Using PSL analysis, the irradiated PD, PK and PKC could be easily distinguished from the non-irradiated ones, while irradiation of the PC at 5 kGy or higher was detectable

Functional activity of symphathetic-adrenal system under chronic and fractionated irradiation of rats

International Nuclear Information System (INIS)

Musagalieva, G.M.

1975-01-01

Chronic irradiation of rats at 5 R twice a week (total dose 400 R) significantly increased adrenaline concentration in the brain, liver and kidney and dophamine and DOPA concentration in liver tissue, adrenal glands and thymus. Fractionated irradiation (chronic irradiation at 400 R plus acute single irradiation at 400 R) increased the adrenaline level in the brain and heart muscle and led to a higher concentration of dophamine and DOPA in the liver, thymus and heart muscle [ru

An overview of food irradiation

International Nuclear Information System (INIS)

Stevenson, M.H.

1991-01-01

This outline survey reviews the subject of food irradiation under the following headings:- brief history, the process (sources, main features of a food processing facility, interaction of radiation with food, main applications of the technology, packaging) consumer concerns (safety, nutritional changes, labelling, detection), international use of food irradiation and legal aspects. (UK)

Super Phenix. Monitoring of structures subject to irradiation. Neutron dosimetry measurement and calculation program

International Nuclear Information System (INIS)

Cabrillat, J.C.; Arnaud, G.; Calamand, D.; Manent, G.; Tavassoli, A.A.

1984-09-01

For the Super Phenix reactor, the evolution, versus the irradiation of the mechanical properties of the core diagrid steel is the object of studies and is particularly monitored. The specimens irradiated, now in PHENIX and will be later irradiated in SUPER PHENIX as soon as the first operating cycles. An important dosimetry program coupling calculation and measurement, is parallely carried out. This paper presents the reasons, the definition of the structure, of the development and of materials used in this program of dosimetry, as also the first results of a calculation-measurement comparison [fr

Electron probe micro-analysis of irradiated Triso-coated UO2 particles, (1)

International Nuclear Information System (INIS)

Ogawa, Toru; Minato, Kazuo; Fukuda, Kosaku; Ikawa, Katsuichi

1983-11-01

The Triso-coated low-enriched UO 2 particles were subjected to the post-irradiation electron probe micro-analysis. Observations and analyses on the amoeba effect, inclusions and solutes in the UO 2 matrix were made. In the cooler side of the particle which suffered extensive kernel migration, two significant features were observed: (1) the wake of minute particles, presumably UO 2 , left by the moving kernel in the carbon phase and (2) carbon precipitation in the pores and along the grain boundaries of the UO 2 kernel. Both features could be hardly explained by the gas-phase mechanism of carbon transport and rather suggest the solid state mechanism. Two-types of 4d-transition metal inclusions were observed: the one which was predominantly Mo with a fraction of Tc and another which was enriched with Ru and containing significant amount of Si. The Mo and Si were also found in the UO 2 matrix; the observation led to the discussion of the oxygen potential in the irradiated Triso-coated UO 2 particle. (author)

Modeling irradiation embrittlement in reactor pressure vessel steels

International Nuclear Information System (INIS)

Odette, G.R.

1998-01-01

As a result of the popularity of the Agencies report 'Neutron Irradiation Embrittlement of Reactor Pressure Vessel Steels' of 1975, it was decided that another report on this broad subject would be of use. In this report, background and contemporary views on specially identified areas of the subject are considered as self-contained chapters, written by experts. In chapter 10, numerical modeling of irradiation embrittlement in reactor vessel steels are introduced. Physically-based models are developed and their role in advancing the state-of-the-art of predicting irradiation embrittlement of RPV steels is stressed

Assessment of different energy delivery settings in laser and LED phototherapies in the inflammatory process of rat's TMJ induced by carrageenan.

Science.gov (United States)

de Castro, Isabele C V; Rosa, Cristiane B; Carvalho, Carolina M; Aragão, Juliana S; Cangussu, Maria Cristina T; Dos Santos, Jean N; Pinheiro, Antonio L B

2015-11-01

Temporomandibular disorders (TMDs) are mostly inflammatory conditions widespread in the population. Previous studies have shown positive effects of either laser or light-emitting diode (LED) phototherapies on treating TMDs, but their action and mechanism in the inflammatory infiltrate of the temporomandibular joint are still poorly understood. The aim of this study was to assess, through histological analysis, the effectiveness of using laser light (λ 780 nm, 70 mW, continous wave (CW), 10 J) and LED (λ 850 ± 10 nm, 100 mW, CW, 10 J) on the inflammation of the temporomandibular joint of rats induced by carrageenan. Forty-five animals were divided into three groups with five animals each according to the experimental times of 2, 3, and 7 days: inflammation, inflammation+laser phototherapy, and inflammation+LED phototherapy. The first irradiation was performed 24 h after induction with an interval of 48 h between sessions. After animal death, specimens were processed and stained with hematoxylin-eosin (HE) and picrosirius. Then, the samples were examined histologically. Data were statistically analyzed. The inflammation group showed mild to moderate chronic inflammatory infiltrate between bone trabecules of the condyle. Over the time course of the study in the laser group, the region of the condyle presented mild chronic inflammation and intense vascularization. In the LED group, the condyle showed aspects of normality and absence of inflammation in some specimens. In all the time points, the laser-irradiated groups showed greater amount of collagen deposition in the condyle (p = 0.04) and in the disc (p = 0.03) when compared to the inflammation and LED groups, respectively. Laser- and LED-treated groups demonstrate a smaller number of layers of the synovial membrane when compared to the non-irradiated groups. It was concluded that, in general, laser and LED phototherapies resulted in a reduction of inflammatory infiltrate in the

Photocatalytic decomposition of selected estrogens and their estrogenic activity by UV-LED irradiated TiO{sub 2} immobilized on porous titanium sheets via thermal-chemical oxidation

Energy Technology Data Exchange (ETDEWEB)

Arlos, Maricor J., E-mail: mjarlos@uwaterloo.ca [Department of Biology, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Liang, Robert; Hatat-Fraile, Melisa M. [Centre for Advanced Materials Joining, Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Waterloo Institute of Nanotechnology, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Bragg, Leslie M. [Department of Biology, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Zhou, Norman Y. [Centre for Advanced Materials Joining, Department of Mechanical and Mechatronics Engineering, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Waterloo Institute of Nanotechnology, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Servos, Mark R. [Department of Biology, University of Waterloo, Waterloo, Ontario N2L 3G1 (Canada); Andrews, Susan A. [Civil Engineering Department, University of Toronto, Toronto, Ontario M5S 1A4 (Canada)

2016-11-15

Highlights: • TiO{sub 2} self-assembled on oxidized porous titanium sheets. • UV-LED/TiO{sub 2} membrane treatment reduced the concentrations of estrogens. • Different pH conditions affect treatment efficiency. • The estrogenic activity removal was similar to the chemical disappearance. - Abstract: The removal of endocrine disrupting compounds (EDCs) remains a big challenge in water treatment. Risks associated with these compounds are not clearly defined and it is important that the water industry has additional options to increase the resiliency of water treatment systems. Titanium dioxide (TiO{sub 2}) has potential applications for the removal of EDCs from water. TiO{sub 2} has been immobilized on supports using a variety of synthesis methods to increase its feasibility for water treatment. In this study, we immobilized TiO{sub 2} through the thermal-chemical oxidation of porous titania sheets. The efficiency of the material to degrade target EDCs under UV-LED irradiation was examined under a wide range of pH conditions. A yeast-estrogen screen assay was used to complement chemical analysis in assessing removal efficiency. All compounds but 17β-estradiol were degraded and followed a pseudo first-order kinetics at all pH conditions tested, with pH 4 and pH 11 showing the most and the least efficient treatments respectively. In addition, the total estrogenic activity was substantially reduced even with the inefficient degradation of 17β-estradiol. Additional studies will be required to optimize different treatment conditions, UV-LED configurations, and membrane fouling mitigation measures to make this technology a more viable option for water treatment.

Fluorescence image excited by a scanning UV-LED light

Science.gov (United States)

Tsai, Hsin-Yi; Chen, Yi-Ju; Huang, Kuo-Cheng

2013-03-01

An optical scanning system using UV-LED light to induced fluorescence technology can enhance a fluorescence image significantly in a short period. It has several advantages such as lower power consumption, no scattering effect in skins, and multilayer images can be obtained to analyze skin disease. From the experiment results, the light intensity increases with increase spot size and decrease scanning speed, but the image resolution is oppositely. Moreover, the system could be widely used in clinical diagnosis and photodynamic therapy for skin disease because even the irradiated time of fluorescence substance is short but it will provide accurately positioning of fluorescence object.

Effect of Red Light-Emitting Diodes Irradiation on Hemoglobin for Potential Hypertension Treatment Based on Confocal Micro-Raman Spectroscopy

Directory of Open Access Journals (Sweden)

Xuejun Qiu

2017-01-01

Full Text Available Red light-emitting diodes (LED were used to irradiate the isolated hypertension hemoglobin (Hb and Raman spectra difference was recorded using confocal micro-Raman spectroscopy. Differences were observed between the controlled and irradiated Hb by comparing the spectra records. The Raman spectrum at the 1399 cm−1 band decreased following prolonged LED irradiation. The intensity of the 1639 cm−1 band decreased dramatically in the first five minutes and then gradually increased in a time-dependent manner. This observation indicated that LED irradiation increased the ability of oxygen binding in Hb. The appearance of the heme aggregation band at 1399 cm−1, in addition to the oxygen marker band at 1639 cm−1, indicated that, in our study, 30 min of irradiation with 15.0 mW was suitable for inhibiting heme aggregation and enhancing the oxygen-carrying capacity of Hb. Principal component analysis showed a one-to-one relationship between irradiated Hb at different time points and the corresponding Raman spectra. Our approach could be used to analyze the hemoglobin from patients with confocal micro-Raman spectroscopy and is helpful for developing new nondrug hypertension therapy.

Wholesomeness studies in the International Food Irradiation Project

Energy Technology Data Exchange (ETDEWEB)

Elias, P S [International Food Irradiation Project, Federal Research Centre for Nutrition

1980-01-01

Despite more than 25 years of history as an effective food preservation method, food irradiation is still subject to strict legislative control in many countries and scientific investigations are required to provide reassurance as to the safety of irradiated food. The International Food Irradiation Project was set up on October 14, 1970 to facilitate the objective evaluation of the wholesomeness of irradiated foodstuffs. Its major activities are; (1) wholesomeness testing of irradiated foods, (2) research on and investigations into the methodology of wholesomeness testing, (3) dissemination of information, and (4) assisting national and international authorities in their consideration of acceptance of irradiated food. In particular, the project over the past nine years had been devoted to the provision of data to national health authorities and international bodies. Up to now, 23 studies were and are being carried out for the project under contract. Subjects for the studies include wheat, wheat flour, potatoes, fish, rice, mango, spices, dried dates, onions and cocoa beans.

Wholesomeness studies in the International Food Irradiation Project

International Nuclear Information System (INIS)

Elias, P.S.

1980-01-01

Despite more than 25 years history as an effective food preservation method, food irradiation is still subject to strict legislative control in many countries and it is required to carry out scientific investigations to reassure the safety of irradiated food. The International Food Irradiation Project was set up on October 14, 1970 to facilitate the objective evaluation of the wholesomeness of irradiated foodstuffs. Its major activities are; (1) wholesomeness testing of irradiated foods, (2) research on and investigations into the methodology of wholesomeness testing, (3) dissemination of information, and (4) assisting national and international authorities in their consideration of acceptance of irradiated food. In particular, the project over the past nine years had been devoted to the provision of data to national health authorities and international bodies. Up to now, 23 studies were and are being carried out for the project under contract. Subject to the studies include wheat, wheat flour, potatoes, fish, rice, mango, spices, dried dates, onions and cocoa beans. (Kitajima, A.)

Single Event Gate Rupture in 130-nm CMOS Transistor Arrays Subjected to X-Ray Irradiation

CERN Document Server

Silvestri, M; Gerardin, Simone; Faccio, Federico; Paccagnella, Alessandro

2010-01-01

We present new experimental results on heavy ion-induced gate rupture on deep submicron CMOS transistor arrays. Through the use of dedicated test structures, composed by a large number of 130-nm MOSFETs connected in parallel, we show the response to heavy ion irradiation under high stress voltages of devices previously irradiated with X-rays. We found only a slight impact on gate rupture critical voltage at a LET of 32 MeV cm(2) mg(-1) for devices previously irradiated up to 3 Mrad(SiO2), and practically no change for 100 Mrad(SiO2) irradiation, dose of interest for the future super large hadron collider (SLHC).

Biochemical and physiological changes in Egyptian Nile fish subjected to varying levels of gamma irradiation

International Nuclear Information System (INIS)

Roushdy, H.M.; El-Kashef, H.S.; Imam, A.E.

1975-01-01

Radiation is nowadays to be considered as a new parameter in the ecology of water masses. Aquatic organisms, perhaps more than any other group of organisms, are directly exposed to radiation hazard and may be subjected to continuous low-level exposure from bottom material and from internal sources accumulated within their own bodies, originating partly from radionuclides released from nuclear facilities into the aquatic environment. In recent years, a large number of papers have been published on the uptake, concentration and release of radioactive material by aquatic organisms. However, radiation experiments on fish, a major source of food for human consumption, are still very rare and mostly restricted to studies on the effect of irradiation on eggs and larvae. Since the study of the radiation effect on living aquatic organisms, particularly fish, is important in connection with the problems of preserving water resources for the benefit of mankind, the work presented here has been done to ascertain the effect of varying dose-levels of gamma irradiation on two common Egyptian Nile fish species, the catfish Clarias lazera and the Tilapia nilotica. Investigations carried out on Clarias lazera involved blood and muscle analyses as well as growth rate measurements. The results obtained showed impaired haematological levels, changes in weight of muscle proteins and, chiefly, retardation in growth rate. Investigations carried out on Tilapia nilotica revealed changes in the activity of certain digestive enzyme systems, glucose level in blood and concentration of the glycogen store in liver and muscles. In discussing the results obtained the authors have taken the relevant literature into consideration. (author)

A new bismuth-based coordination polymer as an efficient visible light responding photocatalyst under white LED irradiation

Energy Technology Data Exchange (ETDEWEB)

Huang, Ya-Jing; Zheng, Yue-Qing, E-mail: zhengyueqing@nbu.edu.cn; Wang, Jin-Jian; Zhou, Lin-Xia

2017-02-15

A new bismuth-based polymer, [Hbpe][Bi(Hpydc){sub 2}(pydc)]·H{sub 2}O (H{sub 2}pydc=pyridine-2,5-dicarboxylic acid, bpe=trans-bis(4-pyridyl) ethylene) has been hydrothermally synthesized. Transient photocurrent response and electrochemical impedance spectroscopy studies indicate that the synthesized polymer with efficient charge separation and transportation can be used as a potential photocatalyst. So we use it for the degradation of rhodamine B (RhB) dye wastewater under visible light. The comparative study on commercial Bi{sub 2}O{sub 3} shows [Hbpe][Bi(Hpydc){sub 2}(pydc)]·H{sub 2}O has the higher photocatalytic performance, with the degradation rate of 97% and 2% within 100 min for [Hbpe][Bi(Hpydc){sub 2}(pydc)]·H{sub 2}O and commercial Bi{sub 2}O{sub 3} respectively. Additionally, the five cycle reproducibility results of [Hbpe][Bi(Hpydc){sub 2}(pydc)]·H{sub 2}O implies that it can be used as a stable photocatalyst. - Graphical abstract: We report a new 1D coordination polymer [Hbpe][Bi(Hpydc){sub 2}(pydc)]·H{sub 2}O by a facile hydrothermal method. The Bi-CP shows good photoelectric property and photocatalytic activity for RhB degradation under visible white LED lamp irradiation. And the stability of the visible-light-responsive bismuth-based coordination polymer has also been examined. - Highlights: • A new Bi(III) coordination polymer is hydrothermally synthesized. • The Bi-CP shows good photoelectric and photocatalytic properties. • Bi-CP shows higher activity than the commercial Bi{sub 2}O{sub 3} for RhB degradation.

Paralysis following stereotactic spinal irradiation in pigs suggests a tolerance constraint for single-session irradiation of the spinal nerve

International Nuclear Information System (INIS)

Medin, Paul M.; Foster, Ryan D.; Kogel, Albert J. van der; Meyer, Jeffrey; Sayre, James W.; Huang, Hao; Öz, Orhan K.

2013-01-01

Background and purpose: Paralysis observed during a study of vertebral bone tolerance to single-session irradiation led to further study of the dose-related incidence of motor peripheral neuropathy. Materials and methods: During a bone tolerance study, cervical spinal nerves of 15 minipigs received bilateral irradiation to levels C5–C8 distributed into three dose groups with mean maximum spinal nerve doses of 16.9 ± 0.3 Gy (n = 5), 18.7 ± 0.5 Gy (n = 5), and 24.3 ± 0.8 Gy (n = 5). Changes developing in the gait of the group of pigs receiving a mean maximum dose of 24.3 Gy after 10–15 weeks led to the irradiation of two additional animals. They received mean maximum dose of 24.9 ± 0.2 Gy (n = 2), targeted to the left spinal nerves of C5–C8. The followup period was one year. Histologic sections from spinal cords and available spinal nerves were evaluated. MR imaging was performed on pigs in the 24.9 Gy group. Results: No pig that received a maximum spinal nerve point dose ⩽19.0 Gy experienced a change in gait while all pigs that received ⩾24.1 Gy experienced paralysis. Extensive degeneration and fibrosis were observed in irradiated spinal nerves of the 24.9 Gy animals. All spinal cord sections were normal. Irradiated spinal nerve regions showed increased thickness and hypointensity on MR imaging. Conclusion: The single-session tolerance dose of the cervical spinal nerves lies between 19.0 and 24.1 Gy for this model

Analysis of the transient response of LED-illuminated diodes under heavy radiation damage

CERN Document Server

Passeri, D; Bilei, G M; Casse, G L; Lemeilleur, F

2000-01-01

The changes of the electrical properties induced by hadron irradiation on silicon detectors have been studied by using the device level simulator HFIELDS. The model of the radiation damage assumes the introduction of radiation-induced acceptor and donor "deep-levels". The electric field profile and the space charge region extension have been calculated for differently irradiated structures. The simulation has been carried out at different biases in order to study the evolution of the space charge region of irradiated detectors as a function of the applied voltages, below and above the full depletion. The time-dependent current responses and the charge collection properties of the structure illuminated by a red LED light have been calculated. The use of the red light results in a shallow (quasi-surface) generation of e-h pairs in silicon, which has been properly taken into account by the simulation. The results of the simulations have been compared to experimental measurements carried out at CERN on samples ir...

Electron irradiation of power transistors

International Nuclear Information System (INIS)

Hower, P.L.; Fiedor, R.J.

1982-01-01

A method for reducing storage time and gain parameters in a semiconductor transistor includes the step of subjecting the transistor to electron irradiation of a dosage determined from measurements of the parameters of a test batch of transistors. Reduction of carrier lifetime by proton bombardment and gold doping is mentioned as an alternative to electron irradiation. (author)

Testing of Performance of Optical Fibers Under Irradiation in Intense Radiation Fields, When Subjected to Very High Temperatures

Energy Technology Data Exchange (ETDEWEB)

Blue, Thomas [The Ohio State Univ., Columbus, OH (United States); Windl, Wolfgang [The Ohio State Univ., Columbus, OH (United States); Dickerson, Bryan [Luna Innovations, Inc. (United States)

2013-01-03

The primary objective of this project is to measure and model the performance of optical fibers in intense radiation fields when subjected to very high temperatures. This research will pave the way for fiber optic and optically based sensors under conditions expected in future high-temperature gas-cooled reactors. Sensor life and signal-to-noise ratios are susceptible to attenuation of the light signal due to scattering and absorbance in the fibers. This project will provide an experimental and theoretical study of the darkening of optical fibers in high-radiation and high-temperature environments. Although optical fibers have been studied for moderate radiation fluence and flux levels, the results of irradiation at very high temperatures have not been published for extended in-core exposures. Several previous multi-scale modeling efforts have studied irradiation effects on the mechanical properties of materials. However, model-based prediction of irradiation-induced changes in silica's optical transport properties has only recently started to receive attention due to possible applications as optical transmission components in fusion reactors. Nearly all damage-modeling studies have been performed in the molecular-dynamics domain, limited to very short times and small systems. Extended-time modeling, however, is crucial to predicting the long-term effects of irradiation at high temperatures, since the experimental testing may not encompass the displacement rate that the fibers will encounter if they are deployed in the VHTR. The project team will pursue such extended-time modeling, including the effects of the ambient and recrystallization. The process will be based on kinetic MC modeling using the concept of amorphous material consisting of building blocks of defect-pairs or clusters, which has been successfully applied to kinetic modeling in amorphized and recrystallized silicon. Using this procedure, the team will model compensation for rate effects, and

Consumer acceptance of irradiated food

Energy Technology Data Exchange (ETDEWEB)

Loaharanu, P [Head, Food Preservation Section, Joint FAO/ IAEA Division of Nuclear Techniques in Food and Agriculture, Wagramerstr. 5, A-1400, Vienna (Austria)

1998-12-31

There was a widely held opinion during the 1970`s and 1980`s that consumers would be reluctant to purchase irradiated food, as it was perceived that consumers would confuse irradiated food with food contaminated by radionuclides. Indeed, a number of consumer attitude surveys conducted in several western countries during these two decades demonstrated that the concerns of consumers on irradiated food varied from very concerned to seriously concerned.This paper attempts to review parameters conducting in measuring consumer acceptance of irradiated food during the past three decades and to project the trends on this subject. It is believed that important lessons learned from past studies will guide further efforts to market irradiated food with wide consumer acceptance in the future. (Author)

Consumer acceptance of irradiated food

Energy Technology Data Exchange (ETDEWEB)

Loaharanu, P. [Head, Food Preservation Section, Joint FAO/ IAEA Division of Nuclear Techniques in Food and Agriculture, Wagramerstr. 5, A-1400, Vienna (Austria)

1997-12-31

There was a widely held opinion during the 1970`s and 1980`s that consumers would be reluctant to purchase irradiated food, as it was perceived that consumers would confuse irradiated food with food contaminated by radionuclides. Indeed, a number of consumer attitude surveys conducted in several western countries during these two decades demonstrated that the concerns of consumers on irradiated food varied from very concerned to seriously concerned.This paper attempts to review parameters conducting in measuring consumer acceptance of irradiated food during the past three decades and to project the trends on this subject. It is believed that important lessons learned from past studies will guide further efforts to market irradiated food with wide consumer acceptance in the future. (Author)

Consumer acceptance of irradiated food

International Nuclear Information System (INIS)

Loaharanu, P.

1997-01-01

There was a widely held opinion during the 1970's and 1980's that consumers would be reluctant to purchase irradiated food, as it was perceived that consumers would confuse irradiated food with food contaminated by radionuclides. Indeed, a number of consumer attitude surveys conducted in several western countries during these two decades demonstrated that the concerns of consumers on irradiated food varied from very concerned to seriously concerned.This paper attempts to review parameters conducting in measuring consumer acceptance of irradiated food during the past three decades and to project the trends on this subject. It is believed that important lessons learned from past studies will guide further efforts to market irradiated food with wide consumer acceptance in the future. (Author)

Electron beam irradiation on cation exchanger used for strontium recovery

International Nuclear Information System (INIS)

Watanabe, Sou; Nakamura, Masahiro; Nomura, Kazunori; Nakajima, Yasuo; Okamoto, Yoshihiro

2014-01-01

Titanate is promising material for radioactive Sr recovery from liquid waste generated in the nuclear facilities. "9"0Sr is one of the most important nuclides in order to release the liquid waste into the environment due to its strong beta-ray decay energy. Although the titanate is applied to radioactive Sr decontamination facility, their resistance to irradiations from radioactive elements adsorbed is not widely investigated so far. In this study, durability of a hydrous titanic acid ion exchanger against beta-ray irradiation were evaluated through electron beam irradiation, elution behaviour of Sr after the irradiation and local structural analysis of the titanate. 1.4 MGy irradiation led to 1% of Sr elution, and the elution could be attributed to defects of O in the titanate induced by the irradiation. Chemical state of Ti of the titanate must be stable up to 2.7 MGy irradiation. (author)

Clinical and symptomatological study of pigs subjected to a lethal dose of integral gamma irradiation

International Nuclear Information System (INIS)

Vaiman, M.; Guenet, J.-L.; Maas, J.; Nizza, P.

1966-05-01

Results are reported from a clinical and haematological study on a Corsican species of pigs wholly exposed to an approximately lethal dose of γ radiation. The aim of this work was to examine the changes in the irradiation syndrome of irradiation for pigs to make it thus possible to devise further experiments, in particular in the therapeutic field. The dose received was 285 rads (measured as the absorption in the vertical antero-posterior medial plane). Data are presented on cyto-haematological changes in the blood circulating immediately after irradiation, and followed up to death, and changes in the medullary cytology after irradiation. The clinical picture of lethal radiation injury in swine is described. (authors) [fr

Food irradiation

International Nuclear Information System (INIS)

Beishon, J.

1991-01-01

Food irradiation has been the subject of concern and controversy for many years. The advantages of food irradiation include the reduction or elimination of dangerous bacterial organisms, the control of pests and insects which destroy certain foods, the extension of the shelf-life of many products, for example fruit, and its ability to treat products such as seafood which may be eaten raw. It can also replace existing methods of treatment which are believed to have hazardous side-effects. However, after examining the evidence produced by the proponents of food irradiation, the author questions whether it has any major contribution to make to the problems of foodborne diseases or world food shortages. More acceptable solutions, he suggests, may be found in educating food handlers to ensure that hygienic conditions prevail in the production, storage and serving of food. (author)

Temperature increase at the light guide tip of 15 contemporary LED units and thermal variation at the pulpal floor of cavities: an infrared thermographic analysis.

Science.gov (United States)

Gomes, M; DeVito-Moraes, A; Francci, C; Moraes, R; Pereira, T; Froes-Salgado, N; Yamazaki, L; Silva, L; Zezell, D

2013-01-01

In this study, a comprehensive investigation on the temperature increase at the light guide tip of several commercial light-emitting diode (LED) light-curing units (LCUs) and the associated thermal variation (ΔT) at the pulpal floor of dental cavities was carried out. In total, 15 LEDs from all generations were investigated, testing a quartz-tungsten-halogen (QTH) unit as a reference. The irradiance level was measured with a power meter, and spectral distribution was analyzed using a spectrometer. Temperature increase at the tip was measured with a type-K thermocouple connected to a thermometer, while ΔT at the pulpal floor was measured by an infrared photodetector in class V cavities, with a 1-mm-thick dentin pulpal floor. The relationship among measured irradiance, ΔT at the tip, and ΔT at the pulpal floor was investigated using regression analyses. Large discrepancies between the expected and measured irradiances were detected for some LCUs. Most of the LCUs showed an emission spectrum narrower than the QTH unit, with emission peaks usually between 450 and 470 nm. The temperature increase at the tip followed a logarithmic growth for LCUs with irradiance ≥1000 mW/cm(2), with ΔT at the tip following the measured irradiance linearly (R(2)=0.67). Linear temperature increase at the pulpal floor over the 40-second exposure time was observed for several LCUs, with linear association between ΔT at the pulpal floor and measured irradiance (R(2)=0.39) or ΔT at the tip (R(2)=0.28). In conclusion, contemporary LED units show varied irradiance levels that affect the temperature increase at the light guide tip and, as a consequence, the thermal variation at the pulpal floor of dental cavities.

Irradiated accelerated corrosion of stainless steel

International Nuclear Information System (INIS)

Raiman, S.S.; Wang, P.; Was, G.S.

2015-01-01

Type 316L stainless steel was exposed to a simulated PWR environment with in-situ proton irradiation to investigate the effect of simultaneous irradiation and corrosion. To enable these experiments, a dedicated beamline was constructed to transport a 3.2 MeV proton beam from a tandem accelerator, through the sample that also acts as the window between the beamline vacuum and a corrosion cell designed to flow primary water at 320 C. degrees and 13.1 MPa. Experiments were conducted on 316L stainless steel samples which were irradiated for 24 hours in 320 C. degrees water with 3 ppm H 2 , at dose rates of 7*10 -6 dpa/s and 7*10 -7 dpa/s, for 4, 24, and 72 hours. A dual-layer oxide formed on the samples, with an inner layer rich in Cr with Fe and Ni content, and an outer layer of Fe oxides. Samples were characterized with TEM (Transmission Electron Microscopy), EDS, and Raman spectroscopy to determine the effect of irradiation. Irradiated samples were found to have a thinner and more porous inner oxide which was deficient in chromium. The outer oxide was found to have significant hematite content, suggesting that irradiation led to an increase in ECP (Electro-Chemical Potential) at the oxide-solution interface, causing accelerated dissolution of the oxide under irradiation. (authors)

Experimental evidence for rhombohedral phase of C70 after irradiation

International Nuclear Information System (INIS)

Misof, K.; Fratzl, P.; Vogl, G.

1993-01-01

Purely f.c.c. C 70 was irradiated with high-energy heavy ions at low temperature. This led to the appearance of additional Bragg peaks attributed to an irradiation-induced f.c.c.-to-rhombohedral phase transition. On heating to about 570 K the retrasition to the pure f.c.c. phase occurred. Since no irradiation-induced phase transition was obsered in C 60 , the rhombohedral phase appears to be connected with the ''rugby-ball shape'' of C 70 which favours the alignment of the molecules. We propose that irradiation provides the agitation enabling the C 70 molecules to overcome the small energy barriers which otherwise prevent the alignment of the rugby balls over larger regions. (orig.)

Improving Quality of Yoghurt By Irradiation

International Nuclear Information System (INIS)

Sallam, E.M.; Nasr, E.H.; Shawki, H.A.

2012-01-01

This investigation was carried out to study the possibility to utilize gamma irradiation to activate starter culture during incubation period and prolong the shelf-life of yoghurt. Starter culture of yoghurt was subjected to gamma irradiation with 10, 15, 20, 25, 30, 35, 40 and 45 Gy to activate the starter then yoghurt was made. Effect of irradiation dose on titratable acidity and the sensory evaluation of all samples were evaluated during incubation period. The obtained results indicated that the irradiation doses 30, 35 and 40 Gy activated the starter and caused significant decreased of incubation period from 4 h to 3.5 h while irradiation doses that less than 30 Gy and more than 40 Gy did not significantly effect. Yoghurt samples were subjected to gamma irradiation with 1.5, 2.5 and 3.5 kGy to prolong the shelf-life of yoghurt samples. The sensory, microbial and chemical properties of yoghurt samples were evaluated during cold storage. The obtained results indicated that the counts of total viable bacteria, molds and yeasts were decreased by applying gamma irradiation. Irradiation treatment caused significant decrease in acidity. The overall acceptability scores, total solid and ph value of all treatments were gradually decreased as the storage period proceeded while total nitrogen of all treatments was not affected. In addition, treatments of yoghurt with 1.5, 2.5 and 3.5 kGy prolonged the shelf-life to 20, 28 and 36 days as compared to 12 days for control treatment

Application of the variational dynamic of nucleic acids with a prognosis of survival in hematological patients subjected to whole-body irradiation for a bone-marrow transplantation

International Nuclear Information System (INIS)

Morera, Lourdes; Garcia, Omar; Proenza, Emma; Carnot, Jose

1996-01-01

The main purpose of this work is to study the variational dynamics of nuclei acids in patients either subjected or not of abortive peaks and its prospective application as a prognostic indicator which might contribute to the therapeutic decision making in cases of BMT and irradiation related acute syndromes

Detoxication of endotoxins from the enteric group of bacteria using gamma-irradiation

Energy Technology Data Exchange (ETDEWEB)

Tumanian, M A; Dunlishcheva, A P; Sinilova, N G; Ivanov, K K

1975-03-01

A study was made of the effect of gamma radiation on the toxic properties of endotoxins of the O-somatic antigens and lipopolysaccharides separated from various representatives of the enterobacteriaceae: S. typhi 2 4446, S. paratyphi B42, B. proteus vulgaris 1 and mirabilis 4, E. coli K12 and 5396/38 and Sh. dysenteriae flexneri 516 and 550. An irradiation dose of 1 mrad led to an insignificant decrease in toxicity, while a dose of 3 mrad led to a decrease in toxicity by a factor of 3 to 4 in comparison with the toxicity of the initial preparation. The decrease in toxicity under the effect of irradiation is apparently connected with the lipid part of the endotoxin molecule. The irradiation results in a decrease in the molecular weight of the endotoxin. The infrared spectrum of the molecule shows considerable changes at high radiation doses. (SJR)

CFD modeling of a UV-LED photocatalytic odor abatement process in a continuous reactor

International Nuclear Information System (INIS)

Wang, Zimeng; Liu, Jing; Dai, Yuancan; Dong, Weiyang; Zhang, Shicheng; Chen, Jianmin

2012-01-01

Highlights: ► A CFD model is developed for a UV-LED based photocatalytic deodorization reactor. ► Radiation field model and Langmuir–Hinshelwood kinetics are integrated in the model. ► The model can predict the pollutant concentration profile and the reactor performance. ► LED distance is predicted to be a critical parameter in photocatalytic reactor design. - Abstract: This paper presents a model study of a UV light-emitting-diode (UV-LED) based photocatalytic odor abatement process. It integrated computational fluid dynamics (CFD) modeling of the gas flow in the reactor with LED-array radiation field calculation and Langmuir–Hinshelwood reaction kinetics. It was applied to simulate the photocatalytic degradation of dimethyl sulfide (DMS) in a UV-LED reactor based on experimentally determined chemical kinetic parameters. A non-linear power law relating reaction rate to irradiation intensity was adopted. The model could predict the steady state DMS concentration profiles by calculating the advection, diffusion and Langmuir–Hinshelwood reaction kinetics. By affecting the radiation intensity and uniformity, the position of the LED array relative to the catalyst appeared to be a critical parameter determining DMS removal efficiency. Too small distances might yield low quantum efficiency and consequently poor abatement performance. This study provided an example of LED-based photocatalytic process modeling and gave insights into the optimization of light source design for photocatalytic applications.

IAEA and food irradiation

International Nuclear Information System (INIS)

Machi, Sueo

1995-01-01

IAEA was founded in 1957. 122 countries take part in it. It is operated with the yearly ordinary budget of about 20 billion yen and the technical cooperation budget of about 6 billion yen and by 2200 personnel. Its two important roles are the promotion of the peaceful utilization of atomic energy and the prevention of nuclear proliferation. The activities of IAEA are shown. The cooperation with developing countries and the international research cooperation program are the important activities. The securing of foods is an urgent subject, and the utilization of radiation and isotopes has been promoted, aiming at sustaining agriculture. The necessity of food irradiation is explained, and at present, commercial food irradiation is carried out in 28 countries including Japan. The irradiation less than 10 kGy does not cause poisonous effect in any food, according to JECFI. The new international agreement is expected to be useful for promoting the international trade of irradiated foods. The international cooperation for the spread of food irradiation and the public acceptance of food irradiation are reported. (K.I.)

Food irradiation in Japan

International Nuclear Information System (INIS)

Ito, Hitoshi

1995-01-01

The basic research on food irradiation in Japan was begun around 1955 by universities and national laboratories. In 1967, food irradiation was designated to the specific general research on atomic energy, and the national project on large scale was continued until 1983. As the result, the treatment of germination prevention for potatoes was approved by the Ministry of Health and Welfare in 1972. The Co-60 gamma ray irradiation facility of Shihoro Agricultural Cooperative is famous as the facility that succeeded in the practical use of food irradiation for the first time in the world. But the practical use of food irradiation stagnates and the research activities were reduced in Japan due to the circumstances thereafter. The effect of radiation to foods and living things is explained. The features of the radiation treatment of foods are small temperature rise, large transmissivity, no residue, the small loss of nutrition and large quantity, continuous treatment. The safety of irradiated foods is explained. The subjects for hereafter are discussed. (K.I.)

Selective lymphoid irradiation. V. Synergism with pretransplant thymectomy or thymic irradiation in cardiac transplantation in rats

International Nuclear Information System (INIS)

Iga, C.; Fawwaz, R.; Nowygrod, R.; Reemtsma, K.; Hardy, M.A.

1985-01-01

Selective lymphoid irradiation (SLI) using palladium-109-hematoporphyrin (Pd-H), given four days prior to transplantation, combined with two doses of antilymphocyte globulin (ALG) (10 mg, days -2 and -1), was evaluated as a method of induction of permanent heterotopic cardiac allograft survival in the highly histoincompatible rat strain combination of ACI (RT1(1))-to-Lewis (RT1a). Both Pd-H and ALG localize poorly in the thymus, so this study evaluated whether thymic irradiation (TI) or thymectomy (TX) of the adult recipient results in indefinite allograft survival. Immunosuppression with Pd-H or ALG alone gave a mean survival time (MST) of 6.7 +/- 0.6 days, but the combination of the two agents led to an MST of 17.6 +/- 3.4 days. When TI was combined with Pd-H and ALG, cardiac allograft survival was prolonged to 50.2 +/- 13.9 days, but TI alone showed an MST of 10.3 +/- 1.8 days. Permanent cardiac allograft survival (greater than 250 days) was achieved in all thymectomized recipients treated with the combination of Pd-H and a brief course of ALG. These animals also accepted second-set skin grafts and rejected third-party skin grafts following more than 150 days of ACI cardiac allograft survival. Thymic irradiation, although effective in acting synergistically with SLI and ALG, led to prolonged, but limited allograft survival, although thymectomy with SLI and ALG is synergistic in prolonging allograft survival permanently without chronic immunosuppression

Food irradiation: a tool for market transformation

International Nuclear Information System (INIS)

Mugliaroli, H.A.

1988-01-01

This paper illustrates the present worldwide importance of food irradiation and the various factors showing that Argentina is in a promising situtation concerning the possibilities of irradiated food exports. A historical summary attached to such analysis makes the subject easily understandable. (Author)

Application of thermoluminescence analysis for detection of irradiated foodstuffs

International Nuclear Information System (INIS)

Malec-Czechowska, K.; Dancewicz, M.; Szot, Z.

1996-01-01

Investigations on the development conditions necessary to obtain reliable results of the detection of irradiated herbs, spices, mushrooms and strawberries by thermoluminescence (Tl) method in whole samples and/or in minerals isolated from them carried out. Tl intensities of whole samples were measured between 40 an 355 C. Threshold values for non-irradiated samples were obtained by multiplying Tl values of control samples by 3 (safety factor). Samples in which Tl intensities were higher than the threshold values were identified as irradiated. In 4 out of 10 kind of herbs and spices examined the results of Tl measurements led to false identification. (author). 14 refs, 1 fig., 5 tabs

High power deep UV-LEDs for analytical optical instrumentation

Czech Academy of Sciences Publication Activity Database

Li, Y.; Dvořák, Miloš; Nesterenko, P. N.; Nuchtavorn, N.; Macka, M.

2018-01-01

Roč. 255, č. 2 (2018), s. 1238-1243 ISSN 0925-4005 Institutional support: RVO:68081715 Keywords : deep UV Light emitting diodes (LEDs) * optical detection * portable analytical instrumentation Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 5.401, year: 2016

The irradiation of human volunteer subjects in research

International Nuclear Information System (INIS)

Rosen, R.

1980-01-01

In medical research radiation is sometimes used to obtain data from healthy individuals. These subjects gain no specific benefit from the research. To safeguard their welfare, constraints are imposed on the dose to be received, on the selection of volunteer subjects, on ensuring their understanding of the procedures and risks, and on obtaining their free consent to participate. The research proposals are assessed by peer review prior to being approved by the host institution. The first example presented describes the use of diagnostic radiography to obtain in vivo data on the femur bone. Conservative dosimetry indicates an expected dose-equivalent per film of 0.5 mSv in bone and 0.18 mSv in bone marrow and gonad tissue. The critical organ total dose-equivalent is estimated to be 7% of the dose-equivalent limit for a volunteer. The second example involves the internal administration of radioactive tracers. Dosimetric calculations indicate an expected whole-body dose-equivalent of 0.5 mSv in the case of C-14 and 0.37 mSv in the case of H-3, these values bejng 10% and 7% of the relevant dose-equivalent limit. Both proposals were given conditional approval. In the generalized research use of volunteer human subjects the rights of the subject, the investigator and the institution need to be protected. At the University of New South Wales procedures have been introduced to govern all experjmental procedures involving human subjects. Some interesting problems which have arisen are discussed. (author)

Protocol for Determining Ultraviolet Light Emitting Diode (UV-LED) Fluence for Microbial Inactivation Studies.

Science.gov (United States)

Kheyrandish, Ataollah; Mohseni, Madjid; Taghipour, Fariborz

2018-06-15

Determining fluence is essential to derive the inactivation kinetics of microorganisms and to design ultraviolet (UV) reactors for water disinfection. UV light emitting diodes (UV-LEDs) are emerging UV sources with various advantages compared to conventional UV lamps. Unlike conventional mercury lamps, no standard method is available to determine the average fluence of the UV-LEDs, and conventional methods used to determine the fluence for UV mercury lamps are not applicable to UV-LEDs due to the relatively low power output, polychromatic wavelength, and specific radiation profile of UV-LEDs. In this study, a method was developed to determine the average fluence inside a water suspension in a UV-LED experimental setup. In this method, the average fluence was estimated by measuring the irradiance at a few points for a collimated and uniform radiation on a Petri dish surface. New correction parameters were defined and proposed, and several of the existing parameters for determining the fluence of the UV mercury lamp apparatus were revised to measure and quantify the collimation and uniformity of the radiation. To study the effect of polychromatic output and radiation profile of the UV-LEDs, two UV-LEDs with peak wavelengths of 262 and 275 nm and different radiation profiles were selected as the representatives of typical UV-LEDs applied to microbial inactivation. The proper setup configuration for microorganism inactivation studies was also determined based on the defined correction factors.

UV irradiation promotes the accumulation of triglyceride in Lipomyces lipofer

International Nuclear Information System (INIS)

Konno, A.; Suzuki, Y.; Ogawa, T.; Taniuchi, T.

2009-01-01

Yeasts of the genus Lipomyces are known as fat yeasts, and they store large amounts of lipids. Because the major lipid produced by Lipomyces is triglyceride, which can be used as a food and energy resource, the control of lipid production by Lipomyces sp. is an important issue. Here we report the effects of UV irradiation on lipid production in Lipomyces lipofer cells. UV irradiation (315-400 nm) led to a 4-fold increase in the amount of triglyceride per cell. We discovered a novel phenomenon, that UV irradiation promotes triglyceride accumulation in L. lipofer. (author)

Effects of light irradiation control on the quality preservation of spinach [Spinacia oleracea] during postharvest storage

International Nuclear Information System (INIS)

Wang, H.; Saito, T.; Shiga, T.

2008-01-01

We examined the effects of the light irradiation on the quality changes of green leafy vegetables after harvest, and clarified the quality preservation method of spinach by the light irradiation with the modified atmosphere effects by the film packaging. Spinach packaged in the sealed film was irradiated at the photosynthetic photon flux density (PPFD) of 4 micromol/square m/s and 10 micromol/square m/s as almost same intensity level as light compensation point by the white fluorescent lamp, white light-emitting diode (LED) and the monochromatic LED's of wavelength at 470nm, 591nm, 626nm and 660nm respectively. The concentration of CO2 in the sealed film was proved to decrease according to the light irradiation regardless of the different wavelength of light, and this showed that the effects of present modified atmosphere packaging is lost by light irradiation. The increase of weight loss by light irradiation was controlled by the film packaging, and then the commercial value was excellently maintained. Light irradiation after harvest contributed to keeping high L-ascorbic acid contents of the spinach. However the light irradiation of different wavelength was not found to influence the change of L-ascorbic acid contents. (author)

Pollination with gamma-irradiated pollen and seed development in kiwifruit (Actinidia deliciosa var. deliciosa)

International Nuclear Information System (INIS)

Musial, K.

1997-01-01

Full text. The effects of pollen irradiation at 70 and 90 kr on seed set were studied in Actinidia deliciosa var. deliciosa. Pollination with irradiated pollen affected seed development and contents. Rising irradiation doses increased the percentages of empty seeds and decreased the percentages of seeds containing embryos with endosperm. Moreover, pollination with heavily irradiated pollen led to the formation of seeds containing the endosperm only. Embryo and endosperm size was also strongly influenced by irradiated pollen. The length of endosperms was reduced at all levels of pollen irradiation compared to the non-irradiated controls; the embryo development was conspicuously retarded. Cells in endosperm resulting from the treatments differed in the presence and number of starch grains. (author)

Assessment of the use of LED phototherapy on bone defects grafted with hydroxyapatite on rats with iron-deficiency anemia and nonanemic: a Raman spectroscopy analysis.

Science.gov (United States)

de Castro, Isabele Cardoso Vieira; Rosa, Cristiane Becher; Dos Reis Júnior, João Alves; Moreira, Luiz Gaudêncio Passos; Aragão, Juliana S; Barbosa, Artur Felipe dos Santos; Silveira, Landulfo; Pinheiro, Antonio L B

2014-09-01

This study aimed to assess bone repair in defects grafted or not with hydroxyapatite (HA) on healthy and iron-deficiency anemia (IDA) rats submitted or not to LED phototherapy (LED-PT) by Raman spectroscopy. The animals were divided in eight groups with five rats each: Clot; Clot + LED; IDA + Clot; IDA + LED; Graft; Graft + LED; IDA + Graft; and IDA + Graft + LED. When appropriated, irradiation with IR LED (λ850 ± 10 nm, 150 mW, CW, Φ = 0.5 cm(2), 16 J/cm(2), 15 days) was carried out. Raman shifts: ∼ 960 [symmetric PO4 stretching (phosphate apatite)], ∼ 1,070 [symmetric CO3 stretching (B-type carbonate apatite)], and ∼ 1,454 cm(-1) [CH2/CH3 bending in organics (protein)] were analyzed. The mean peak values for ∼ 960, ∼ 1,070, and ∼ 1,454 cm(-1) were nonsignificantly different on healthy or anemic rats. The group IDA + Graft + LED showed the lowest mean values for the peak ∼ 960 cm(-1) when compared with the irradiated IDA group or not (p ≤ 0.001; p ≤ 0.001). The association of LED-PT and HA-graft showed lowest mean peak at ∼ 1,454 cm(-1) for the IDA rats. The results of this study indicated higher HA peaks as well as a decrease in the level of organic components on healthy animals when graft and LED phototherapy are associated. In the other hand, IDA condition interfered in the graft incorporation to the bone as LED phototherapy only improved bone repair when graft was not used.

Detection of low amount of irradiated ingredients in non-irradiated precooked meals

Science.gov (United States)

Marchioni, Eric; Horvatovich, Peter; Ndiaye, Bara; Miesch, Michel; Hasselmann, Claude

2002-03-01

The application of the European Standards for the detection of irradiated food by thermoluminescence of silicates, electron-spin resonance spectroscopy of bones or gas chromatography-mass spectrometry of 2-alkylcyclobutanones does not allow the detection of irradiated ingredients included in small quantity in the matrix of a food which has not been irradiated, but which could be subjected to various processing technologies such as cooking, freezing or storage. The use of an enzymatic food hydrolysis carried out at moderated temperature, for the extraction of the food-contaminating silicate minerals and bone fragments, followed by a purification of the extracts by a high-density aqueous solution of sodium polytungstate, allows a simultaneous detection of weak inclusions (0.1% m:m) of irradiated spices and mechanically deboned turkey meat (MRM) included in various precooked foods. Moreover, the use of a supercritical fluid extraction procedure for the 2-alkylcyclobutanones or an additional purification step of the lipid extracts made it possible to lower the detection limit of the 2-alkylcyclobutanones radiation-induced from triglycerides. Using gas chromatography-mass spectrometry, down to 0.5% (m:m) of irradiated MRM included in non-irradiated chicken quenelles could be detected.

Detection of low amount of irradiated ingredients in non-irradiated precooked meals

International Nuclear Information System (INIS)

Marchioni, Eric; Horvatovich, Peter; Ndiaye, Bara; Miesch, Michel; Hasselmann, Claude

2002-01-01

The application of the European Standards for the detection of irradiated food by thermoluminescence of silicates, electron-spin resonance spectroscopy of bones or gas chromatography-mass spectrometry of 2-alkylcyclobutanones does not allow the detection of irradiated ingredients included in small quantity in the matrix of a food which has not been irradiated, but which could be subjected to various processing technologies such as cooking, freezing or storage. The use of an enzymatic food hydrolysis carried out at moderated temperature, for the extraction of the food-contaminating silicate minerals and bone fragments, followed by a purification of the extracts by a high-density aqueous solution of sodium polytungstate, allows a simultaneous detection of weak inclusions (0.1% m:m) of irradiated spices and mechanically deboned turkey meat (MRM) included in various precooked foods. Moreover, the use of a supercritical fluid extraction procedure for the 2-alkylcyclobutanones or an additional purification step of the lipid extracts made it possible to lower the detection limit of the 2-alkylcyclobutanones radiation-induced from triglycerides. Using gas chromatography-mass spectrometry, down to 0.5% (m:m) of irradiated MRM included in non-irradiated chicken quenelles could be detected

Food irradiation - a Northern Ireland dimension

International Nuclear Information System (INIS)

McMurray, C.H.; Stevenson, M.H.

1988-01-01

Irradiation is a technology which has been exploited in a wide variety of industries ranging from sterilization of medical products and polymer modification to applications with respect to food. Whilst food irradiation has recently become a controversial subject, the process has been studied for many years. Many products could be irradiated to advantage and these need to be thoroughly investigated before final recommendations can be made as to the commercial feasibility and suitability of the processing technology in the Northern Ireland context

S-phase cell distribution in the small intestine irradiated at different times of the day. I. Acute irradiation injury

Energy Technology Data Exchange (ETDEWEB)

Becciolini, A; Balzi, M; Cremonini, D; Fabbrica, D [Florence Univ. (Italy). Ist. di Radiologia

1983-01-01

The S-phase cell distribution has been analysed to evaluate the behaviour of proliferative cells in the intestinal epithelium after irradiation at different times of the day. A marked reduction of S cell frequency was observed at early intervals after abdominal irradiation; this reduction was particularly evident in the lower half of the crypts. At subsequent intervals a progressive extension of the proliferative compartment, with labelled cells also at the top of the crypt, was present. The irradiated groups generally showed a homogeneous behaviour even if a more marked reduction in S-phase cells was observed in group C. The invertase activity, a brush border enzyme synthetized during the differentiation process, presented a different behaviour at the early intervals in the irradiated groups. When the extension of the proliferative compartment occurred the invertase activity reached values close to zero. The modifications in brush border enzymes and in S-phase cell distribution, at early killing times, led to the hypothesis of an early differentiation.

Application of Photocatalysts and LED Light Sources in Drinking Water Treatment

Directory of Open Access Journals (Sweden)

Gopal Achari

2013-09-01

Full Text Available This study investigates a cross-section of TiO2 compositions for which existing evidence suggests the prospect of improved performance compared to standard Degussa P25. In the context of a program aimed toward a 365 nm LED based photo-reactor, the question is whether a distinctly superior photocatalyst composition for drinking water treatment is now available that would shape design choices. An answer was sought by synthesizing several photocatalysts with reported high reactivity in some context in the literature, and by performing photocatalysts reactivity tests using common pollutants of water system including Natural Organic Matter (NOM and Emerging Contaminants (ECs from the pesticide and pharmaceutical classes. 365 nm Light Emitting Diodes (LEDs were used as the irradiation source. Since LEDs are now available in the UV, we did not examine the TiO2 modifications that bring band gap excitation into the region beyond 400 nm. The results suggest that the choice of the photocatalyst should be best made to fit the reactor design and photocatalyst mounting constraints such as mass transport, reactive surface, and light field. No photocatalyst composition overall, superior for all classes emerged.

Irradiation as a quarantine treatment

International Nuclear Information System (INIS)

Burditt, A.K. Jr.

1991-01-01

The use of irradiation as an alternative treatment for commodities subject to infestation by pests of quarantine importance is outlined in this article. A dose of 300 Gy or less has been found to prevent adult emergence when insect eggs or larvae are irradiated and research has shown that such doses will not affect the quality of most commodities. The use of gamma rays from cobalt-60 or caesium-137 sources, as well as electrons or X-rays from linear accelerators, has been approved for food irradiation. Irradiation facilities must meet regulations promulgated by nuclear, health and agricultural quarantine agencies with regard to location, facility design, sources, operation, personnel, dosimetry and other requirements. Education of industry operators and the general public is needed in order to gain acceptance of irradiation as a quarantine treatment. (author). 21 refs, 1 tab

Packing for food irradiation

Energy Technology Data Exchange (ETDEWEB)

Chmielewski, A G [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)

2006-07-01

Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)

Packing for food irradiation

International Nuclear Information System (INIS)

Chmielewski, A.G.

2006-01-01

Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)

The irradiation of volunteers in medical research

International Nuclear Information System (INIS)

Rae, S.

1976-01-01

Attempts to produce guidelines for use in medical research involving the irradiation of volunteers are surveyed. The recommendations of the British Institute of Radiology (Irradiation of Human Subjects for Medical Research, Bull. Brit. Radiology, 1975, vol.1, no.2, 4) are summarized. These recommendations, based on a preliminary working document produced by the World Health Organization, are considered in three parts, the selection of subjects, the categorisation and the approval of research projects. The importance of freely given and informed consent is emphasized. The suggested four categories of project are classified by the amount of total body radiation to be received by the subject in each project, and the necessary assessment and prior approval procedures are related to this classification. The imposition of a lifetime exposure limit is compared with occupational exposures which are assessed on an annual basis, and the ICRP's 'planned special exposures'. Repeated irradiation of the same subject, although permissible within the recommended limits, may create difficulties. The total lifetime accumulated dose may not always be immediately available if the subject has worked in a number of different establishments. The possibility of compiling an approved list of procedures to reduce some of the anticipated delays in processing applications is discussed. (author)

Effects of irradiation on mechanical properties

International Nuclear Information System (INIS)

Server, W.L.; Griesbach, T.J.; Dragunov, Y.; Amaev, A.

1998-01-01

As a result of the popularity of the Agencies report 'Neutron Irradiation Embrittlement of Reactor Pressure Vessel Steels' of 1975, it was decided that another report on this broad subject would be of use. In this report, background and contemporary views on specially identified areas of the subject are considered as self-contained chapters, written by experts. The effects of irradiation on the mechanical properties of reactor pressure vessel steels are explained. This chapter provides some background on the critical elements controlling neutron damage effects. Distinction is made between vessels made in the USA and in the former USSR

Accumulation of lipid peroxidation products in eye structures of mice subjected to whole-body X-irradiation

International Nuclear Information System (INIS)

Sakina, N.L.; Dontsov, A.E.; Afanas'ev, G.G.; Ostrovskij, M.A.; Pelevina, I.I.

1990-01-01

In studying the effect of whole-body X-irradiation on the accumulation of lipid peroxidation products (conjugated dienes, TBA-active products, and Sciff bases) in retina and retinal pigmented epithelium of pigmented and nonpigmented mice it was shown that irradiation of dark-pigmented mice does not cause even a slight accumulation of lipid peroxidation products as compared to that in the controls. Albino mice exhibited a marked increase in the level of lipid peroxidation products which was manifested soon after irradiation and persisted for at least 3 months after irradiation. Melanine is suggested to participate in protecting eye structures against pro-oxidizing action of ionizing radiation

Effects of hyperthermia and X-irradiation on mouse stromal tissue

International Nuclear Information System (INIS)

Wondergem, J.; Haveman, J.

1986-01-01

The sensitivity of normal stroma to heat, irradiation and heat combined with irradiation, was studied using the tumour bed effect (TBE) assay. Irradiation before implantation led to a TBE, dose dependent below 15 Gy, but remaining relatively constant above. The interval (0-90 days) between irradiation and tumour implantation did not influence the magnitude of the TBE. Hyperthermia with large heat doses (45-60 min at 44 0 C) before implantation may lead to a TBE. The interval between hyperthermia and tumour implantation was very important. Results showed that the recovery from heat-induced stromal damage is very rapid. When the interval between hyperthermia and tumour implantation was 10 days or longer, no TBE could be observed. Irradiation combined with large heat doses (30-60 min at 44 0 C) decreased the radiation-induced TBE. The combination of irradiation with mild heat treatments (15 min at 44 0 C) could lead to a larger TBE then after irradiation alone. When hyperthermia was given prior to irradiation, the interval between heat and irradiation proved to be very important. With large intervals (21 days or longer), TBE values were about the same as with irradiation alone. When heat was given after irradiation, irradiation-induced TBE was always reduced. (UK)

Blood bactericidal activity in Hiroshima subjects

Energy Technology Data Exchange (ETDEWEB)

Hollingsworth, J W; Hamilton, H B

1961-03-07

A simple screening method for blood bactericidal activity was developed for study of irradiated atomic bomb survivors and nonirradiated subjects in Hiroshima. Blood bactericidal activity was found to be a relatively constant biological phenomenon in all subjects studied. No differences in activity were detected in relationship to radiation exposure in 1945. 17 references, 6 tables.

Sensory acceptability evaluation of irradiated rice, oryza sativa indica

International Nuclear Information System (INIS)

Loaharanu, S.; Sutantawong, M.; Ungsunanatawiwat, A.

1971-01-01

The non-glutinous and glutinous types of polished rice, Oryza sativa indica were subjected to gamma rays at ambient temperature and stored at 27+-1 0 C for one week. The irradiated rice was cooked and tasted by members of trained panel. Using Hedonic scale and Triangle test, the acceptability of irradiated rice was justified. Gamma irradiation up to 100 krads did not significantly cause off-color, off-odor and off flavor in irradiated non-glutino rice. Glutinous rice irradiated at 60 krads could not be significantly differentiated from non-irradiated sample

Irradiation Microstructure of Austenitic Steels and Cast Steels Irradiated in the BOR-60 Reactor at 320°C

Science.gov (United States)

Yang, Yong; Chen, Yiren; Huang, Yina; Allen, Todd; Rao, Appajosula

Reactor internal components are subjected to neutron irradiation in light water reactors, and with the aging of nuclear power plants around the world, irradiation-induced material degradations are of concern for reactor internals. Irradiation-induced defects resulting from displacement damage are critical for understanding degradation in structural materials. In the present work, microstructural changes due to irradiation in austenitic stainless steels and cast steels were characterized using transmission electron microscopy. The specimens were irradiated in the BOR-60 reactor, a fast breeder reactor, up to 40 dpa at 320°C. The dose rate was approximately 9.4x10-7 dpa/s. Void swelling and irradiation defects were analyzed for these specimens. A high density of faulted loops dominated the irradiated-altered microstructures. Along with previous TEM results, a dose dependence of the defect structure was established at 320°C.

Post-irradiation inactivation, protection, and repair of the sulfhydryl enzyme malate synthase

International Nuclear Information System (INIS)

Durchschlag, H.; Zipper, P.

1985-01-01

Malate synthase from baker's yeast, a trimeric sulfhydryl enzyme with one essential sulfhydryl group per subunit, was inactivated by 2 kGy X-irradiation in air-saturated aqueous solution (enzyme concentration: 0.5 mg/ml). The radiation induced changes of enzymic activity were registered at about 0,30,60 h after irradiation. To elucidate the role of OH - , O 2 , and H 2 O 2 in the X-ray inactivation of the enzyme, experiments were performed in the absence of presence of different concentrations of specific additives (formate, superoxide dismutase, catalase). These additives were added to malate synthase solutions before or after X-irradiation. Moreover, repairs of inactivated malate synthase were initiated at about 0 or 30 h after irradiation by means of the sulfhydryl agent dithiothreitol. Experiments yielded the following results: 1. Irradiation of malate synthase in the absence of additives inactivated the enzyme immediately to a residual activity Asub(r)=3% (corresponding to a D 37 =0.6 kGy), and led to further slow inactivation in the post-irradiation phase. Repairs, initiated at different times after irradiation, restored enzymic activity considerably. The repair initiated at t=0 led to Asub(r)=21%; repairs started later on resulted in somewhat lower activities. The decay of reparability, however, was found to progress more slowly than post-irradiation inactivation itself. After completion of repair the activities of repaired samples did not decrease significantly. 2. The presence of specific additives during irradiation caused significant protective effects against primary inactivation. The protection by formate was very pronounced (e.g., Asub(r)=72% and D 37 =6 kGy for 100 mM formate). The presence of catalytic amounts of superoxide dismutase and/or catalase exhibited only minor effects, depending on the presence and concentration of formate. (orig.)

Investigation on the effects of gamma irradiation on bitumen

International Nuclear Information System (INIS)

Mello, M.S.; Braz, D.; Motta, L.M.G.

2011-01-01

Brazil has more than 218,000 km of asphalt-paved highways. Bitumen is a generic term for natural or manufactured black or dark-colored solid, semisolid, or viscous cementitious materials that are composed mainly of high molecular weight hydrocarbons (90-95%). Several papers have shown that the irradiation process has changed the mechanical behavior in some polymers. This work aims to analyze the behavior of Brazilian irradiated Bitumen (CAP 50-70). In order to provide a preliminary evaluation, bitumen samples and cylindrical specimens of asphaltic mixture were tested. The bitumen samples were irradiated 0.1 to 300 kGy, and asphaltic mixture specimen was irradiated 5 to 300 kGy. The cylindrical asphaltic mixture specimen of 10.16 cm diameter used in this study was molded using an asphalt-aggregate mixture. The specimens were irradiated in LIN/UFRJ/Brazil using a Gamma cell Co 60 source of gamma irradiation with an applied dose rate of 29.7 Gy/min. After irradiated, the bitumen samples were subjected to penetration test and the asphaltic mixtures were subjected to indirect tensile strength test (diametral compression) for determination of the resilient modulus, according to ASTM method D 4123. The results of these experiments for each dose were compared with the control (nonirradiated). As expected, the penetration results showed that the ratio (irradiated/non-irradiated) decreases with increasing of irradiation dose for bitumen samples and the resilient modulus results showed that the ratio (irradiated/non-irradiated) increases with increasing of irradiation dose for asphaltic mixture. (author)

LED phototherapy in full-thickness burns induced by CO2 laser in rats skin.

Science.gov (United States)

da Silva Melo, Milene; Alves, Leandro Procópio; Fernandes, Adriana Barrinha; Carvalho, Henrique Cunha; de Lima, Carlos José; Munin, Egberto; Gomes, Mônica Fernandes; Salgado, Miguel Angel Castillo; Zângaro, Renato Amaro

2018-04-27

Many studies have been conducted on the treatment of burns because they are important in morbidity and mortality. These studies are mainly focused on improving care and quality of life of patients. The aim of this study was evaluate the LED phototherapy effects in rats skin full-thickness burns induced by CO 2 laser. The animals were divided in NT group that did not received any treatment and LED group that received LED irradiation at 685 nm, 220 mW, and 4.5 J/cm 2 during 40 s by burned area. Biopsies were obtained after 7, 14, and 21 days of treatment and submitted to histological and immunohistochemical analysis. The LED phototherapy shows anti-inflammatory effects, improves angiogenesis, and stimulates the migration and proliferation of fibroblasts. The T CD8+ lymphocytes were more common in burned areas compared to T CD4+ lymphocytes since statistically significant differences were observed in the LED group compared to the NT group after 7 days of treatment. These results showed that LED phototherapy performs positive influence in full-thickness burns repair from the healing process modulated by cellular immune response. The obtained results allowed inferring that burns exhibit a characteristic cell immune response and this cannot be extrapolated to other wounds such as incision and wounds induced by punch, among others.

Changes in the physiological characteristics of mature pear fruits subjected to gamma irradiation

International Nuclear Information System (INIS)

Mahmoud, A.A.; Sewidan, A.M.; Roushdy, H.M.; Taha, F.

1988-01-01

Moisture content, weight loss, firmness, titrable acidity total soluble solids and decay percentage of the pear fruits (variety of Le conte) of different treatments (0,1,2,3, and 4 KGy) were investigated during storage. The data reported show that there was a slight decrease in the moisture content and titrable acidity of pear fruits during storage and there was decrease in the firmness and decay percentage. This decrease was elevated by the increase of irradiation doses and storage period on the other hand, the weight losses and total soluble solids increased by increasing the irradiation doses and storage period

Post-irradiation examinations of THERMHET composite fuels for transmutation

Science.gov (United States)

Noirot, J.; Desgranges, L.; Chauvin, N.; Georgenthum, V.

2003-07-01

The thermal behaviour of composite targets dedicated to minor actinide transmutation was studied using THERMHET (thermal behaviour of heterogeneous fuel) irradiation in the SILOE reactor. Three inert matrix fuel designs were tested (macro-mass, jingle and microdispersion) all with a MgAl 2O 4 spinel inert matrix and around 40% weight of UO 2 to simulate minor actinide inclusions. The post-irradiation examinations led to a new interpretation of the temperature measurement by thermocouples located in the central hole of the pellets. A major change in the micro-dispersed structure was detected. The examinations enabled us to understand the behaviour of the spinel during the different stages of irradiation. They revealed an amorphisation at low temperature and then a nano re-crystallisation at high temperature of the spinel in the micro-dispersed case. These results, together with those obtained in the MATINA irradiation of an equivalent structure, show the importance of the irradiation temperature on spinel behaviour.

Post-irradiation examinations of THERMHET composite fuels for transmutation

Energy Technology Data Exchange (ETDEWEB)

Noirot, J. E-mail: jnoirot@cea.fr; Desgranges, L.; Chauvin, N.; Georgenthum, V

2003-07-01

The thermal behaviour of composite targets dedicated to minor actinide transmutation was studied using THERMHET (thermal behaviour of heterogeneous fuel) irradiation in the SILOE reactor. Three inert matrix fuel designs were tested (macro-mass, jingle and microdispersion) all with a MgAl{sub 2}O{sub 4} spinel inert matrix and around 40% weight of UO{sub 2} to simulate minor actinide inclusions. The post-irradiation examinations led to a new interpretation of the temperature measurement by thermocouples located in the central hole of the pellets. A major change in the micro-dispersed structure was detected. The examinations enabled us to understand the behaviour of the spinel during the different stages of irradiation. They revealed an amorphisation at low temperature and then a nano re-crystallisation at high temperature of the spinel in the micro-dispersed case. These results, together with those obtained in the MATINA irradiation of an equivalent structure, show the importance of the irradiation temperature on spinel behaviour.

Post-irradiation examinations of THERMHET composite fuels for transmutation

International Nuclear Information System (INIS)

Noirot, J.; Desgranges, L.; Chauvin, N.; Georgenthum, V.

2003-01-01

The thermal behaviour of composite targets dedicated to minor actinide transmutation was studied using THERMHET (thermal behaviour of heterogeneous fuel) irradiation in the SILOE reactor. Three inert matrix fuel designs were tested (macro-mass, jingle and microdispersion) all with a MgAl 2 O 4 spinel inert matrix and around 40% weight of UO 2 to simulate minor actinide inclusions. The post-irradiation examinations led to a new interpretation of the temperature measurement by thermocouples located in the central hole of the pellets. A major change in the micro-dispersed structure was detected. The examinations enabled us to understand the behaviour of the spinel during the different stages of irradiation. They revealed an amorphisation at low temperature and then a nano re-crystallisation at high temperature of the spinel in the micro-dispersed case. These results, together with those obtained in the MATINA irradiation of an equivalent structure, show the importance of the irradiation temperature on spinel behaviour

Sterilization of Escherichia coli by using near-UV LED and TiO{sub 2} nanofibers that were prepared by using electrostatic spray

Energy Technology Data Exchange (ETDEWEB)

Lee, Dong-Gil; Hong, Ji-Tae; Son, Min-Kyu; Lee, Kyoung-Jun; Xu, Guo-Cheng; Prabakar, Kandasamy; Kim, Hee-je, E-mail: heeje@pusan.ac.k [Department of Electrical Engineering Pusan National University, 30 Jangjeon-dong, Geumjeong-gu, Busan 609-735 (Korea, Republic of)

2010-05-01

TiO{sub 2} nanofiber films were prepared by a homemade electrostatic spray method at 13 kV using a high power supply. As-prepared TiO{sub 2} was used to sterilize enteropathogenic Escherichia coli in polluted water by using near-UV LEDs at three different wavelengths with variable exposure time and frequency of irradiation. Irrespective of the wavelength of the light source used, longer irradiation times such as 1 h completely inactivated the E. coli. However, a wavelength of 375 nm was effective in inactivating in a shorter irradiation time (15 min). When the frequency of irradiation was 1 kHz, almost 95% of the E. coli was inactivated after 30 min exposure.

Design of an Oximeter Based on LED-LED Configuration and FPGA Technology

OpenAIRE

Stojanovic, Radovan; Karadaglic, Dejan

2013-01-01

A fully digital photoplethysmographic (PPG) sensor and actuator has been developed. The sensing circuit uses one Light Emitting Diode (LED) for emitting light into human tissue and one LED for detecting the reflectance light from human tissue. A Field Programmable Gate Array (FPGA) is used to control the LEDs and determine the PPG and Blood Oxygen Saturation (SpO2). The configurations with two LEDs and four LEDs are developed for measuring PPG signal and Blood Oxygen Saturation (SpO2). N-LEDs...

The study on the electrical resistivity of Cu/V multilayer films subjected to helium (He) ion irradiation

Science.gov (United States)

Wang, P. P.; Xu, C.; Fu, E. G.; Du, J. L.; Gao, Y.; Wang, X. J.; Qiu, Y. H.

2018-05-01

Sputtering-deposited Cu/V multilayer films with the individual layer thickness varying from 2.5 nm to 100 nm were irradiated by 1 MeV helium (He) ion at the fluence of 6 ×1016 ions ·cm-2 at room temperature. The resistivity of Cu/V multilayer films after ion irradiation was evaluated as a function of individual layer thickness at 300 K and compared with their resistivity before ion irradiation. The results show that the resistivity change before and after ion irradiation is largely determined by the interface structure, grain boundary and radiation induced defects. A model amended based on the model used in describing the resistivity of as-deposited Cu/V multilayer films was proposed to describe the resistivity of ion irradiated Cu/V multilayer films by considering the point defects induced by ion irradiation, the effect of interface absorption on defects and the effect of interface microstructure in the multilayer films.

General views about specimen irradiations in reactors; Considerations generales sur'les irradiations d'echantillons dans les reacteurs

Energy Technology Data Exchange (ETDEWEB)

Seguin, M [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1965-07-01

Specimen irradiation of fissile or non-fissile materials, carried out under circumstances becoming more and more severe and in reactor of increasing flux bas led to an evolution of irradiation rigs. A survey of the problems arising from irradiating under these various circumstances leads to conclude that it is possible to devise one capsule type suitable to every particular case, and that in a wide temperature range. Consequently, once the various irradiation-parameters known, a general method of calculation can be followed so as to determine the various sizes of the parts constituting the capsule. These theoretical calculations might sometimes be corrected through benefits gained from previous irradiations. Similarly, practical experimentation might allow to foresee more handy assembling of the capsule, specimen loading-and unloading being easier at the same time. (author) [French] L'irradiation d'echantillons, fissiles ou non fissiles, dans des conditions imposees de plus en plus strictes et dans des reacteurs a flux de plus en plus eleve, a eu pour consequence une evolution dans la conception des dispositifs d'irradiation. Lorsqu'on examine les problemes souleves par ces differentes irradiations, on en conclut qu'il est possible de concevoir un type de capsule capable de donner satisfaction dans chaque cas particulier, et ce, dans une tres large gamme de temperature. Par consequent, les differents parametres de l'irradiation etant connus, une methode generale de calcul peut etre suivie pour determiner les differentes cotes des pieces constitutives de la capsule. Ces calculs theoriques devront quelquefois etre corriges grace aux enseignements tires d'irradiations precedentes. De meme, l'experience acquise permettra d'envisager un montage plus aise de la capsule, tout en facilitant l'enfournement et le defournement des echantillons.

Irradiation of food

International Nuclear Information System (INIS)

MacGregor, J.; Stanbrook, I.; Shersby, M.

1989-01-01

The House of Commons was asked to support the Government's intention to allow the use of the irradiation of foodstuffs under conditions that will fully safeguard the interests of the consumer. The Government, it was stated, regards this process as a useful additional way to ensure food safety. The effect of the radiation in killing bacteria will enhance safety standards in poultry meat, in some shell-fish and in herbs and spices. The problem of informing the public when the food has been irradiated, especially as there is no test to detect the irradiation, was raised. The subject was debated for an hour and a half and is reported verbatim. The main point raised was over whether the method gave safer food as not all bacteria were killed in the process. The motion was carried. (U.K.)

Effect of gamma irradiation on rheological properties of polysaccharides exuded by A. fluccosus and A. gossypinus.

Science.gov (United States)

Alijani, Samira; Balaghi, Sima; Mohammadifar, Mohammad Amin

2011-11-01

In this study, Iranian gum tragacanth (GT) exudates from Astragalus fluccosus (AFG) and Astragalus gossypinus (AGG) were irradiated at 3, 7, 10 and 15 kGy. Fourier transform infrared spectroscopy (FTIR) data showed that irradiation did not induce changes in the chemical structure of either type of gum. Although particle size distribution and both steady shear and dynamic rheological properties were considerably affected by the irradiation process, the magnitude of the effect of irradiation on each of the rheological and size variables was different for the hydrocolloids. For instance, for AGG, increasing the irradiation dose from 3 to 10 kGy, the d(0.5) and D[3,2] values were reduced by one-sixth to one-eighth fold. Colour measurement revealed that the radiation process led to an increase in the yellow index and b* values for both types of GT in powder form, but it was more pronounced for AGG samples. Irradiation led to an approximate 13-fold increase in redness in AFG. Surface and shape changes of the gum crystals were studied by scanning electron microscope (SEM) and a smoother surface for irradiated samples was detected. The notable changes in functional properties of each variety of irradiated gum should be taken into consideration before using the radiation technology as a commercial tool for sterilisation. Copyright © 2011 Elsevier B.V. All rights reserved.

Effect of 710 nm visible light irradiation on neurite outgrowth in primary rat cortical neurons following ischemic insult

International Nuclear Information System (INIS)

Choi, Dong-Hee; Lee, Kyoung-Hee; Kim, Ji-Hye; Kim, Moon Young; Lim, Jeong Hoon; Lee, Jongmin

2012-01-01

Highlights: ► 710 nm wavelength light (LED) has a protective effect in the stroke animal model. ► We determined the effects of LED irradiation in vitro stroke model. ► LED treatment promotes the neurite outgrowth through MAPK activation. ► The level of synaptic markers significantly increased with LED treatment. ► LED treatment protects cell death in the in vitro stroke model. -- Abstract: Objective: We previously reported that 710 nm Light-emitting Diode (LED) has a protective effect through cellular immunity activation in the stroke animal model. However, whether LED directly protects neurons suffering from neurodegeneration was entirely unknown. Therefore, we sought to determine the effects of 710 nm visible light irradiation on neuronal protection and neuronal outgrowth in an in vitro stroke model. Materials and methods: Primary cultured rat cortical neurons were exposed to oxygen-glucose deprivation (OGD) and reoxygenation and normal conditions. An LED array with a peak wavelength of 710 nm was placed beneath the covered culture dishes with the room light turned off and were irradiated accordingly. LED treatments (4 min at 4 J/cm 2 and 50 mW/cm 2 ) were given once to four times within 8 h at 2 h intervals for 7 days. Mean neurite density, mean neurite diameter, and total fiber length were also measured after microtubule associated protein 2 (MAP2) immunostaining using the Axio Vision program. Synaptic marker expression and MAPK activation were confirmed by Western blotting. Results: Images captured after MAP2 immunocytochemistry showed significant (p < 0.05) enhancement of post-ischemic neurite outgrowth with LED treatment once and twice a day. MAPK activation was enhanced by LED treatment in both OGD-exposed and normal cells. The levels of synaptic markers such as PSD 95, GAP 43, and synaptophysin significantly increased with LED treatment in both OGD-exposed and normal cells (p < 0.05). Conclusion: Our data suggest that LED treatment may promote

Rapid biodiesel production using wet microalgae via microwave irradiation

International Nuclear Information System (INIS)

Wahidin, Suzana; Idris, Ani; Shaleh, Sitti Raehanah Muhamad

2014-01-01

Highlights: • Lipid was directly extracted from wet microalgae using microwave irradiation. • The microwave irradiation and water bath-assisted solvent extraction are applied. • Cell walls are significantly disrupted under microwave irradiation. • Highly disrupted cell walls led to higher biodiesel yield in microwave irradiation. • Microwave irradiation is a promising direct technique with high biodiesel yields. - Abstract: The major challenges for industrial commercialized biodiesel production from microalgae are the high cost of downstream processing such as dewatering and drying, utilization of large volumes of solvent and laborious extraction processes. In order to address these issues the microwave irradiation method was used to produce biodiesel directly from wet microalgae biomass. This alternative method of biodiesel production from wet microalgae biomass is compared with the conventional water bath-assisted solvent extraction. The microwave irradiation extracted more lipids and high biodiesel conversion was obtained compared to the water bath-assisted extraction method due to the high cell disruption achieved and rapid transesterification. The total content of lipid extracted from microwave irradiation and water bath-assisted extraction were 38.31% and 23.01% respectively. The biodiesel produced using microwave irradiation was higher (86.41%) compared to the conventional method. Thus microwave irradiation is an attractive and promising technology to be used in the extraction and transesterification process for efficient biodiesel production

Effects of UV irradiation and UV/chlorine co-exposure on natural organic matter in water

International Nuclear Information System (INIS)

Liu, Wei; Zhang, Zaili; Yang, Xin; Xu, Yiyue; Liang, Yongmei

2012-01-01

The effects of co-exposure to ultraviolet (UV) irradiation (with either low- or medium-pressure UV lamps) and free chlorine (chloramine) at practical relevant conditions on changes in natural organic matter (NOM) properties were investigated using four waters. The changes were characterized using the specific disinfection by-product formation potential (SDBPFP), specific total organic halogen formation potential (STOXFP), differential UV absorbance (∆UVA), and size-exclusion chromatography (SEC). The results for exposure to UV irradiation alone and for samples with no exposure were also obtained. The SDBPFPs in all UV-irradiated NOM waters observed were higher than those of non-irradiated samples. UV irradiation led to increases in STOXFPs as a result of chlorination, but no changes, or only small decreases, from chloramination. UV irradiation alone led to positive ∆UVA spectra of the four NOM waters; co-exposure to UV and chlorine gave larger negative ∆UVA spectra than those obtained by chlorine exposure alone. No obvious changes in SEC results were observed for samples only irradiated with UV light; co-exposure gave no detectable changes in the abundances of small fractions for exposure to chlorine only. Both UV photooxidation and photocatalytic oxidation appear to affect the reactivity of the NOM toward subsequent chlorination, and the magnitude of the changes is generally greater for medium-pressure lamps than for low-pressure lamps. These results suggest that applying UV disinfection technology to a particular source may not always be disinfection by-product-problem-free, and the interactions between UV light, chlorine, and NOM may need to be considered. - Highlights: ► We discussed the effects of co-exposure to UV light and chlorine on properties of natural organic matters in waters. ► UV irradiation led to increases in SDBPFP and STOXFP of NOM waters from chlorination. ► We suggest that applying an UV disinfection technology to a particular

Identification of Gamma Irradiation of Imported Spice

International Nuclear Information System (INIS)

Han, S.B.; Suh, C.S.; Choi, I.D.; Kim, B.K.; Song, H.P.; Byun, M.W.; Kim, D.H.

2004-01-01

Photostimulated Luminescence (PSL), Electron Spin Resonance (ESR) and Thermoluminescence (TL) analysis were conducted to detect irradiation treatment of imported whole and ground spices. The screening by PSL detected no irradiation treatment, except un the ground thyme and bay leaves which exhibited photon counts in the intermediate level. Irradiation of the two spices was detected after irradiating them at 1.0, 3.0, 5.0 and 10.0 kGy, and then subjecting them to PSL analysis, which resulted in the significantly low photons of non-irradiated spices compared to that at 1.0 kGy, indicating that the photon counts varied depending on the amount of inorganic mineral debris in the spices

Protective role of coriandrum sativum oily extracts on ehrlich tumour bearing mice subjected to gamma irradiation

International Nuclear Information System (INIS)

El-Sayed Aly, S.M.

2000-01-01

This study was planned to evaluate the potency of coriandrum, sativum oily extract [in a dose of 1 mg/kg body weight; for six successive doses] as a chemopreventive agent against solid ehrlich tumour transplanted to the thigh of the left leg of mice subjected or not to gamma irradiation. The protective role of coriander oil was assessed through studying the level of serum phosphorus, calcium, prostaglandins, and anti-thyroid antibodies levels. Meanwhile, the content of cholesterol and triacylglycerols both in hepatic and tumor tissues were also measured. The levels of serum calcium ions revealed significant decline in the tested groups as compared with the control ones. Measurements of serum PGE 2 and anti-thyroid antibodies levels exhibited significant fluctuated changes as compared with the control levels. Serum phosphorus levels induced only non-significant changes. The contents of cholesterol both in hepatic and tumor tissues induced significant decline in the tested proups as compared with the control ones

Feedback-Controlled LED Photobioreactor for Photophysiological Studies of Cyanobacteria

Energy Technology Data Exchange (ETDEWEB)

Melnicki, Matthew R.; Pinchuk, Grigoriy E.; Hill, Eric A.; Kucek, Leo A.; Stolyar, Sergey; Fredrickson, Jim K.; Konopka, Allan; Beliaev, Alex S.

2013-04-09

A custom photobioreactor (PBR) was designed to enable automatic light adjustments using computerized feedback control. A black anodized aluminum enclosure, constructed to surround the borosilicate reactor vessel, prevents the transmission of ambient light and serves as a mount for arrays of light-emitting diodes (LEDs). The high-output LEDs provide narrow-band light of either 630 or 680 nm for preferential excitation of the cyanobacterial light-harvesting pigments, phycobilin or chlorophyll a, respectively. Custom developed software BioLume provides automatic control of optical properties and a computer feedback loop can automatically adjust the incident irradiance as necessary to maintain a fixed transmitted light through the culture, based on user-determined set points. This feedback control serves to compensate for culture dynamics which have optical effects, (e.g., changing cell density, pigment adaptations) and thus can determine the appropriate light conditions for physiological comparisons or to cultivate light-sensitive strains, without prior analyses. The LED PBR may also be controlled as a turbidostat, using a feedback loop to continuously adjust the rate of media-dilution based on the transmitted light measurements, with a fast and precise response. This cultivation system gains further merit as a high-performance analytical device, using non-invasive tools (e.g., dissolved gas sensors, online mass spectrometry) to automate real-time measurements, thus permitting unsupervised experiments to search for optimal growth conditions, to monitor physiological responses to perturbations, as well as to quantitate photophysiological parameters using an in situ light-saturation response routine.

In vitro pulp chamber temperature rise from irradiation and exotherm of flowable composites.

Science.gov (United States)

Baroudi, Kusai; Silikas, Nick; Watts, David C

2009-01-01

The aim of this study was to investigate the pulpal temperature rise induced during the polymerization of flowable and non-flowable composites using light-emitting diode (LED) and halogen (quartz-tungsten-halogen) light-curing units (LCUs). Five flowable and three non-flowable composites were examined. Pulpal temperature changes were recorded over 10 min in a sample primary tooth by a thermocouple. A conventional quartz-tungsten-halogen source and two LEDs, one of which was programmable, were used for light curing the resin composites. Three repetitions per material were made for each LCU. There was a wide range of temperature rises among the materials (P < 0.05). Temperature rises ranged between 1.3 degrees C for Filtek Supreme irradiated by low-power LED and 4.5 degrees C for Grandio Flow irradiated by high-power LED. The highest temperature rises were observed with both the LED high-power and soft-start LCUs. The time to reach the exothermic peak varied significantly between the materials (P < 0.05). Pulpal temperature rise is related to both the radiant energy output from LCUs and the polymerization exotherm of resin composites. A greater potential risk for heat-induced pulp damage might be associated with high-power LED sources. Flowable composites exhibited higher temperature rises than non-flowable materials, because of higher resin contents.

[State of the reproductive systemin in male rats of 1st generation obtained from irradiated parents and exposed to electromagnetic radiation (897 MHz) during embryogenesis and postnatal development].

Science.gov (United States)

Vereshchako, G G; Chueshova, N V; Gorokh, G A; Naumov, A D

2014-01-01

The consequences of prolonged exposure to electromagnetic radiation from cellular phone (897 MHz, daily 8 h/day) in male rats of the 1st generation obtained from irradiated parents and subjected to prolonged exposure to electromagnetic radiation of the range of mobile communications during ontogeny and postnatal development were studied. It has been found that irradiation causes a decrease in the number of births of animals, changing the sex ratio towards the increase in the number of males. It had a significant impact on the reproductive system of males, accelerating their sexual development, revealed at the age of two months. Radiation from cell phones led to significant disproportions in the cell number at different stages of spermatogenesis. It increased the number of mature spermatozoa which decreased viability.

Physicochemical evaluation of the effects of irradiation and evisceration on the conservation of refrigerated blackfin tuna (Thunnus atlanticus)

Energy Technology Data Exchange (ETDEWEB)

Monteiro, Maria L.G.; Marsico, Eliane T. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Faculdade de Veterinaria. Dept. de Tecnologia de Alimentos], e-mail: marialuciaguerra@yahoo.com.br, e-mail: elianee@vm.uff.br; Vital, Helio C. [Centro Tecnologico do Exercito (CTEx), Rio de Janeiro, RJ (Brazil). Secao de Defesa Nuclear], e-mail: vital@ctex.eb.br

2009-07-01

Tuna is among the most traded fishes in Brazil, however efficiently delaying its fast deterioration is still a major practical challenge. Irradiation has been proposed as a safe and powerful alternative tool for conservation of seafood. This work investigated the effects of irradiation on the physicochemical quality of refrigerated blackfin tuna (Thunnus atlanticus). Analyses of pH, total volatile bases (TVB-N), ammonia and biogenic amines (histamine, cadaverine and putrescine) were performed in order to determine the degree of conservation. The samples were subjected to four different treatments aiming at evaluating the efficiency of irradiation, evisceration and both combined. The figures measured for those parameters, all of them related to the degree of conservation, were found to increase with time regardless of the treatment. In addition, data for irradiated samples remained consistently lower than for unirradiated ones, indicating a better level of preservation that led to an extended shelf life of 14 days. In contrast, excessive levels of those indicators of degradation were found in unirradiated samples after 7 to 10 days of storage. In addition, some evidence was found that evisceration slightly increased quality, consequently promoting a small extension in shelf life of unirradiated samples. Finally, it can be concluded with basis on the results of the physicochemical parameters studied that treatment of fresh refrigerated blackfin tuna by irradiation with 2.5 kGy efficiently preserved freshness and extended the shelf life of the product from 7 to 14 days. (author)

Physicochemical evaluation of the effects of irradiation and evisceration on the conservation of refrigerated blackfin tuna (Thunnus atlanticus)

International Nuclear Information System (INIS)

Monteiro, Maria L.G.; Marsico, Eliane T.; Vital, Helio C.

2009-01-01

Tuna is among the most traded fishes in Brazil, however efficiently delaying its fast deterioration is still a major practical challenge. Irradiation has been proposed as a safe and powerful alternative tool for conservation of seafood. This work investigated the effects of irradiation on the physicochemical quality of refrigerated blackfin tuna (Thunnus atlanticus). Analyses of pH, total volatile bases (TVB-N), ammonia and biogenic amines (histamine, cadaverine and putrescine) were performed in order to determine the degree of conservation. The samples were subjected to four different treatments aiming at evaluating the efficiency of irradiation, evisceration and both combined. The figures measured for those parameters, all of them related to the degree of conservation, were found to increase with time regardless of the treatment. In addition, data for irradiated samples remained consistently lower than for unirradiated ones, indicating a better level of preservation that led to an extended shelf life of 14 days. In contrast, excessive levels of those indicators of degradation were found in unirradiated samples after 7 to 10 days of storage. In addition, some evidence was found that evisceration slightly increased quality, consequently promoting a small extension in shelf life of unirradiated samples. Finally, it can be concluded with basis on the results of the physicochemical parameters studied that treatment of fresh refrigerated blackfin tuna by irradiation with 2.5 kGy efficiently preserved freshness and extended the shelf life of the product from 7 to 14 days. (author)

Neutron irradiation effects in reactor pressure vessel steels and weldments. Working document

International Nuclear Information System (INIS)

1998-10-01

As a result of the popularity of the Agencies report 'Neutron Irradiation Embrittlement of Reactor Pressure Vessel Steels' of 1975, it was decided that another report on this broad subject would be of use. In this report, background and contemporary views on specially identified areas of the subject are considered as self-contained chapters, written by experts. A separate abstract was prepared for the introduction and for each of the eleven chapters, which are: 1. Reactor Pressure Vessel Design, 2. Reactor Pressure Materials, 3. WWER Pressure Vessels, 4. Determination of Mechanical Properties, 5. Neutron Exposure, 6. Methodology of Irradiation Experiments, 7. Effect of Irradiation on Mechanical Properties, 8. Mechanisms of Irradiation Embrittlement, 9. Modelling of Irradiation Damage, 10. Annealing of Irradiation Damage, 11. Safety Assessment using Surveillance Programmes and Data Bases

Consumer attitude toward food irradiation

International Nuclear Information System (INIS)

Bruhn, C.M.M.

1986-01-01

Consumer attitudes toward food irradiation were evaluated. The influence of educational efforts on consumer concern for the safety of irradiated products and willingness to buy irradiated foods were measured. Demographic and psychological factors were studied in relation to attitudes. An educational leaflet describing current scientific information regarding the safety, advantages, and disadvantages of food irradiation was developed and used in two studies evaluating attitude change. In the first study, attitude change among two groups of consumers with different philosophic orientations was measured. In a second study, the effectiveness of an educational leaflet received through the mail and a poster display were examined. In a third study response to food irradiation was related to value hierarchy, locus of control, innovativeness, and demographic parameters. Initially, subjects showed a higher concern for other areas of food safety, particularly the use of chemicals and sprays on food, than toward food irradiation. After educational efforts, conventional consumers expressed minor concern toward irradiation whereas ecologically sensitive alternative consumers obtained from a food cooperative expressed major concern. A knowledgeable discussion leader lowered irradiation concern among conventional consumers. In contrast, concern among alternative consumers did not diminish when given the opportunity to discuss safety issues with a knowledgeable person

Irradiation tests of THTR fuel elements in the DRAGON reactor (irradiation experiment DR-K3)

International Nuclear Information System (INIS)

Burck, W.; Duwe, R.; Groos, E.; Mueller, H.

1977-03-01

Within the scope of the program 'Development of Spherical Fuel Elements for HTR', similar fuel elements (f.e.) have been irradiated in the DRAGON reactor. The f.e. were fabricated by NUKEM and were to be tested under HTR conditions to scrutinize their employability in the THTR. The fuel was in the form of coated particles moulded into A3 matrix. The kernels of the particles were made of mixed oxide of uranium and thorium with an U 235 enrichment of 90%. One aim of the post irradiation examination was the investigation of irradiation induced changes of mechanical properties (dimensional stability and elastic behaviour) and of the corrosion behaviour which were compared with the properties determined with unirradiated f.e. The measurement of the fission gas release in annealing tests and ceramografic examinations exhibited no damage of the coated particles. The measured concentration distribution of fission metals led to conclusions about their release. All results showed, that neither the coated particles nor the integral fuel spheres experienced any significant changes that could impair their utilization in the THTR. (orig./UA) [de

Swift heavy ion irradiation induced modification of structure

Indian Academy of Sciences (India)

AFM analysis indicated that the pristine film consists of agglomerated grains with diffuse grain boundary. Irradiation led to reduced agglomeration of the grains with the formation of sharper grain boundaries. The rms roughness (rms) estimated from AFM analysis increased from 6.2 in pristine film to 12.7 nm when the film ...

Structural changes in chromosomes of peripheral blood lymphocytes in monkeys subjected to long-term daily irradiation

International Nuclear Information System (INIS)

Kosichenko, L.P.

1976-01-01

During the period that lasted from 4 to 11 years after the cessation of the long-term daily gamma-irradiation the frequency of chromosome rearrangements in peripheral blood lymphocytes of monkeys exceeded the control level. The number of rearrangements did not change significantly with different total irradiation doses (from 826 to 3677r). The main type of structural chromosome rearrangements were symmetrical chromosome exchanges. Abnormal cell clones in peripheral lymphocytes in monkeys irradiated with low doses exhibited no selective advantages during the periods of investigation

Short-range order of amorphous FeNiB alloy after neutron irradiation

International Nuclear Information System (INIS)

Miglierini, M.; Sitek, J.; Baluch, S.; Cirak, J.; Lipka, J.

1990-01-01

Transmission Moessbauer spectroscopy was used to study irradiation-induced changes in the short-range order of an amorphous Fe 80-x Ni x B 20 alloy. Neutron irradiation led to an increase of the width of a hyperfine field distribution implying atomic rearrangement towards disordering. Changes in a mean value of a HFD and Moessbauer line areas can be associated with a reorientation of spins due to radiation damage. (orig.)

Study on the cytogenetic activity of freshly irradiated potatoes

International Nuclear Information System (INIS)

Zajtsev, A.N.; Osipova, I.N.

1978-01-01

Cytogenetic activity of potatoes, subjected to gamma irradiation in the dose of 10 Krad, feeding the animals in a day after irradiation, has been investigated. The frequency of chromosomal aberrations in bone marrow cells of mice, who obtained newly irradiated raw or baked potatoes, has no substantial difference from the analogous mutageneity index of mice from the control group. The data obtained are of practical importance when considering the problem of using gamma-irradiated potatoes in the people nourishment

Protection of lethally irradiated mice with allogeneic fetal liver cells: influence of irradiation dose on immunologic reconstitution

International Nuclear Information System (INIS)

Tulunay, O.; Good, R.A.; Yunis, E.J.

1975-01-01

After lethal irradiation long-lived, immunologically vigorous C3Hf mice were produced by treatment with syngeneic fetal liver cells or syngeneic newborn or adult spleen cells. Treatment of lethally irradiated mice with syngeneic or allogeneic newborn thymus cells or allogeneic newborn or adult spleen cells regularly led to fatal secondary disease or graft-versus-host reactions. Treatment of the lethally irradiated mice with fetal liver cells regularly yielded long-lived, immunologically vigorous chimeras. The introduction of the fetal liver cells into the irradiated mice appeared to be followed by development of immunological tolerance of the donor cells. The findings suggest that T-cells at an early stage of differentiation are more susceptible to tolerance induction than are T-lymphocytes at later stages of differentiation. These investigations turned up a perplexing paradox which suggests that high doses of irradiation may injure the thymic stroma, rendering it less capable of supporting certain T-cell populations in the peripheral lymphoid tissue. Alternatively, the higher and not the lower dose of irradiation may have eliminated a host cell not readily derived from fetal liver precursors which represents an important helper cell in certain cell-mediated immune functions, e.g., graft-versus-host reactions, but which is not important in others, e.g., allograft rejections. The higher dose of lethal irradiation did not permit development or maintenance of a population of spleen cells that could initiate graft-versus-host reactions but did permit the development of a population of donor cells capable of achieving vigorous allograft rejection

Molecular Engineering of UV/Vis Light-Emitting Diode (LED)-Sensitive Donor-π-Acceptor-Type Sulfonium Salt Photoacid Generators: Design, Synthesis, and Study of Photochemical and Photophysical Properties.

Science.gov (United States)

Wu, Xingyu; Jin, Ming; Xie, Jianchao; Malval, Jean-Pierre; Wan, Decheng

2017-11-07

A series of donor-π-acceptor-type sulfonium salt photoacid generators (PAGs) were designed and synthesized by systematically changing electron-donating groups, π-conjugated systems, electron-withdrawing groups, and the number of branches through molecular engineering. These PAGs can effectively decompose under UV/Vis irradiation from a light-emitting diode (LED) light source because of the matching absorption and emitting spectra of the LEDs. The absorption and acid-generation properties of these sulfonium salts were elucidated by UV/Vis spectroscopy and so forth. Results indicated that the PAG performance benefited from the introduction of strong electron-donating groups, specific π-conjugated structures, certain electron-withdrawing groups, or two-branched structures. Most sulfonium salts showed potential as photoinitiators under irradiation by a wide variety of UV and visible LEDs. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The effect of gamma radiation on the rice moth, Corcyra Cephalonica (Staint). Part II irradiation of the eggs, pupae, and adults

International Nuclear Information System (INIS)

Loaharanu, S.; Sutantawong, M.; Ungsunanatwiwat, A.

1971-01-01

The 1-3 days old eggs of the rice moth were exposed to gamma rays at 0, 3, 6, 12.5 and 25 krads. The LD 50 and LD 99 for eggs was estimated as 9 and 42 krads respectively. A dose of 25 krads caused 100% mortality in larvae irradiated as egg stage. Mixed ages of 1-7 days old pupae were subjected to 0, 6, 12.5, 25, 50 and 100 Krads of gamma rays. Based on number of adults emerged, the LD 50 and LD 99 for pupae were estimated as 19 and 110 krads. Mixed sexes of 1-3 days old adult moths were also exposed to gamma rays. The LD 50 and LD 99 for adults appeared to be 60 and 170 krads respectively. Irradiation of both sexes of adult moths at 25 and 50 krads, led to complete infertility in eggs deposited

Photodynamic action of LED-activated pyropheophorbide-α methyl ester in cisplatin-resistant human ovarian carcinoma cells

International Nuclear Information System (INIS)

Tan, Y; Xia, X S; Yu, H P; Bai, D Q; He, Y; Xu, C S; Leung, A W N

2009-01-01

Cisplatin-resistance is a major obstacle for the successful therapy to ovarian cancer, and exploring novel approach to deactivate cisplatin-resistant ovarian cells will improve the clinical outcomes. Our present study showed that there was no dark cytotoxicity of MPPa in the COC1/DDP cells at the dose of 0.25 – 4 μM, and LED-activated MPPa resulted in drug dose- and light-dependent cytotoxicity. Apoptotic rate 6 h after LED-activated MPPa (2 μM) increased to 16.71% under the light energy of 1 J/cm 2 . Confocal laser scanning microscopy showed that MPPa mainly localized in the intracellular membrane system, namely the endoplasmic reticulum, Golgi apparatus, lysosomes and mitochondria in the COC1/DDP cells. Mitochondrial membrane potential (ΔΨ m ) was collapsed when COC1/DDP cells were exposed to 2 μM MPPa for 20 h and then 1 J/cm 2 irradiation of LED source. These data demonstrated that LED-activated MPPa significantly deactivated cisplatin-resistant ovarian cell line COC1/DDP cells and enhanced apoptosis and decreased ΔΨ m , which suggests LED is an efficient light source for PDT and LED-activated MPPa can be developed as new modality for treating cisplatin-resistant ovarian

Test marketing and consumer acceptance of irradiated meat products

International Nuclear Information System (INIS)

Xu Zhicheng; Feng Zhixiong; Jiang Peizhen

2001-01-01

This study consists of two parts: irradiation processing of cooked meat and irradiation preservation of prepackaged chilled fresh cut meats. Irradiation of prepackaged pickled meat products dipped in grains stillage at a dose 6-8 kGy eliminated common food-borne microorganisms, such as E. Coli and other microbial pathogens and extended the shelf life of the product to 10 days at 5 deg. C. Test marketing of 40,000 bags (about 10,000 kg) of the product in more than 100 supermarkets in the city of Shanghai showed no untoward problem with consumer acceptance. Irradiation of prepackaged chilled fresh cut pork at a dose 3 kGy led to inactivation of microbial pathogens and parasites with a concomitant reduction in numbers of common spoilage microorganisms and extension of shelf life of the product for 30 days at 5 deg. C. The cost benefit and marketing applications were evaluated. (author)

Development of UV absorbing PET through Electron Irradiation

International Nuclear Information System (INIS)

Kim, Jung Woo; Lee, Na Eun; Lim, Hyung San; Park, Yang Jeong; Cho, Sung Oh

2017-01-01

Experiment to increase UV absorbance through electron beam irradiation on PET was performed. Moreover, surface hardness and roughness of each sample were observed to find the key factor increasing UV absorbance. PET sheets were irradiated with an electron beam at various fluences. The irradiated samples, as well as pristine sample, were subjected to UV-visible spectral study(UV-Vis), pencil hardness test, and scanning electron microscopy(SEM) experiment. In this study, PET samples irradiated at several conditions were analyzed through various measurements. UV absorbance-another meaning of transmittance in this study- of irradiated PET sample increased compared with pristine sample as fluence was increased in UV-Visible spectroscopy experiment.

The wholesomeness of irradiated food

International Nuclear Information System (INIS)

Elias, P.S.; Matsuyama, A.

1978-01-01

It is apparent that there is a need for protection of the consumer and a need for governmental authorities to insure a safe and wholesome food supply for the population. Based on objective and scientific evidence regarding the safety of food irradiation, national and international health authorities are able to determine whether irradiated food is acceptable for human consumption. Following a thorough review of all available data, the Joint FAO/IAEA/WHO Expert Committee unconditionally approved wheat and ground wheat products and papaya irradiated for disingestation at a maximum dose of 100 krad, potatoes irradiated for sprout control at a maximum dose not exceeding 15 krad, and chicken irradiated at a maximum dose of 700 krad to reduce microbiological spoilage. Lastly, it unconditionally approved strawberries irradiated at a maximum dose of 300 krad to prolong storage. Onions at irradiated for sprout control at a maximum dose of 15 krad were temporarily approved, subject to preparation of further data on multigeneration reproduction studies on rats. Codfish and redfish eviscerated after irradiation at a maximum dose of 220 krad to reduce microbiological spoilage were also approved, based on the results of various studies in progress. Temporary, conditional approval of rice irradiated for insect disinfestation at a maximum dose of 100 krad was based on results of long-term studies on rats and monkies, available in the next review. Due to insufficient data, no decision regarding irradiated mushrooms was made. (Bell, E.)

Design of an Oximeter Based on LED-LED Configuration and FPGA Technology

Directory of Open Access Journals (Sweden)

Radovan Stojanovic

2013-01-01

Full Text Available A fully digital photoplethysmographic (PPG sensor and actuator has been developed. The sensing circuit uses one Light Emitting Diode (LED for emitting light into human tissue and one LED for detecting the reflectance light from human tissue. A Field Programmable Gate Array (FPGA is used to control the LEDs and determine the PPG and Blood Oxygen Saturation (SpO2. The configurations with two LEDs and four LEDs are developed for measuring PPG signal and Blood Oxygen Saturation (SpO2. N-LEDs configuration is proposed for multichannel SpO2 measurements. The approach resulted in better spectral sensitivity, increased and adjustable resolution, reduced noise, small size, low cost and low power consumption.

Design of an oximeter based on LED-LED configuration and FPGA technology.

Science.gov (United States)

Stojanovic, Radovan; Karadaglic, Dejan

2013-01-04

A fully digital photoplethysmographic (PPG) sensor and actuator has been developed. The sensing circuit uses one Light Emitting Diode (LED) for emitting light into human tissue and one LED for detecting the reflectance light from human tissue. A Field Programmable Gate Array (FPGA) is used to control the LEDs and determine the PPG and Blood Oxygen Saturation (S(p)O(2)). The configurations with two LEDs and four LEDs are developed for measuring PPG signal and Blood Oxygen Saturation (S(p)O(2)). N-LEDs configuration is proposed for multichannel S(p)O(2) measurements. The approach resulted in better spectral sensitivity, increased and adjustable resolution, reduced noise, small size, low cost and low power consumption.

Spacing optimization of high power LED arrays for solid state lighting

Energy Technology Data Exchange (ETDEWEB)

Chan, Y. Sing; Lee, S. W. Ricky, E-mail: rickylee@ust.hk [Electronic Packaging Laboratory, Center for Advanced Microsystems Packaging, Hong Kong University of Science and Technology (Hong Kong)

2011-01-15

This paper provides an analytical approach to determine the optimum pitch by utilizing a thermal resistance network, under the assumption of constant luminous efficiency. This work allows an LED array design which is mounted on a printed circuit board (PCB) attached with a heat sink subject to the natural convection cooling. Being validated by finite element (FE) models, the current approach can be shown as an effective method for the determination of optimal component spacing in an LED array assembly for SSL. (semiconductor devices)

Method and equipment to lead a cable-like material under an irradiation source

International Nuclear Information System (INIS)

Riesselmann, F.J.

1975-01-01

When irradiating cable-like material (cable jacketed with polyethylene) which is led through an irradiation source and is thus turned and twisted, no uniform irradiation and twist changes have so far been obtained. It is suggested to twist the cable before the first circuit by about 45 0 in one direction, after turning and the second circuit, to twist by about 90 0 in the other direction and to follow with a further two circuits with twisting. A suitable cable twisting device which works with discrete clamping jaw is described in detail. (UWI) [de

Ethical and social implications of microdosing clinical trial (3). Radiological protection of human subjects in research

International Nuclear Information System (INIS)

Kurihara, Chieko

2008-01-01

Internal irradiation of human subjects in research is discussed. Radiological protection of human subjects in medical research in a framework of radiation protection is surveyed from a viewpoint of general life-ethics and research-ethics. A workshop 'On the internal irradiation of human subjects' to summarize special and systematic knowledge was organized by Research Center for Radiation Protection, National Institute of Radiological Sciences in the beginning of 2008. Activities of this workshop are introduced. Discussion covers also (1) Research ethics and radiation protection, (2) Fundamentals and applications of risk-benefit assessment, (3) Human subjects risk assessment in ICRP recommendation, (4) Mechanism of human subjects internal irradiation assessment, and (5) Present status and future prospects in Japan. (K.Y.)

Irradiation tests of optoelectronic components for LHC inner-detectors

International Nuclear Information System (INIS)

Dawson, I.; Oglesby, S.J.; Dowell, J.D.; Homer, R.J.; Kenyon, I.R.; Shaylor, H.R.; Wilson, J.A.

1997-01-01

Two kinds of optical-link technologies have been investigated for the readout of data at LHC experiments; one based on LEDs and the other on Multi-Quantum-Well modulators. Presented in this paper are the results of irradiating LEDs and MQW modulators with 1 MeV-equivalent neutrons and 24 GeV protons. The devices were biased and the performances of the optical links were monitored throughout the tests. The fluences achieved were ∝5 x 10 14 n cm -2 and ∝6 x 10 13 p cm -2 . (orig.)

Irradiation hazards and safety standards for patients in dental radiography

Energy Technology Data Exchange (ETDEWEB)

Williamson, B D.P.

1975-07-01

The historical developments which have led to a reduction in the hazards or potential hazards to patients in dental radiography are reviewed. Based on a simple risk estimate, the safety of present-day techniques employed in routine dental radiography is assessed. Also included in the review is a description of techniques used and results obtained from the National Radiation Laboratory's (NRL) surveillance programme of patients' exposure to irradiation in dental radiography. The possibilities of and need for achieving further reductions of irradiation are discussed.

Negative pion irradiation of mammalian cells

International Nuclear Information System (INIS)

Dertinger, H.; Luecke-Huhle, C.; Schlag, H.; Weibezahn, K.F.

1976-01-01

Monolayers and spheroids of Chinese hamster cells (V79) were subjected to negative pion irradiation under aerobic conditions. R.b.e. values in the pion peak of 1.8 and 1.5 were obtained for monolayers and spheroids, respectively, whereas the r.b.e. for the plateau was found to be slightly higher than 1. In addition, it was observed that the higher resistance of the V79 spheroid cells than the monolayers to γ-irradiation is not diminished in the pion peak, suggesting that the underlying phenomenon of intercellular communication influences cell survival even after high-LET irradiation. (author)

Various approaches in EPR identification of gamma-irradiated plant foodstuffs: A review.

Science.gov (United States)

Aleksieva, Katerina I; Yordanov, Nicola D

2018-03-01

Irradiation of food in the world is becoming a preferred method for their sterilization and extending their shelf life. For the purpose of trade with regard to the rights of consumers is necessary marking of irradiated foodstuffs, and the use of appropriate methods for unambiguous identification of radiation treatment. One-third of the current standards of the European Union to identify irradiated foods use the method of the Electron Paramagnetic Resonance (EPR) spectroscopy. On the other hand the current standards for irradiated foods of plant origin have some weaknesses that led to the development of new methodologies for the identification of irradiated food. New approaches for EPR identification of radiation treatment of herbs and spices when the specific signal is absent or disappeared after irradiation are discussed. Direct EPR measurements of dried fruits and vegetables and different pretreatments for fresh samples are reviewed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optogenetic activation of neocortical neurons in vivo with a sapphire-based micro-scale LED probe

Directory of Open Access Journals (Sweden)

Niall eMcAlinden

2015-05-01

Full Text Available Optogenetics has proven to be a revolutionary technology in neuroscience and has advanced continuously over the past decade. However, optical stimulation technologies for in vivo need to be developed to match the advances in genetics and biochemistry that have driven this field. In particular, conventional approaches for in vivo optical illumination have a limitation on the achievable spatio-temporal resolution. Here we utilize a sapphire-based microscale gallium nitride light-emitting diode (µLED probe to activate neocortical neurons in vivo. The probes were designed to contain independently controllable multiple µLEDs, emitting at 450 nm wavelength with an irradiance of up to 2 W/mm2. Monte-Carlo stimulations predicted that optical stimulation using a µLED can modulate neural activity within a localized region. To validate this prediction, we tested this probe in the mouse neocortex that expressed channelrhodopsin-2 (ChR2 and compared the results with optical stimulation through a fiber at the cortical surface. We confirmed that both approaches reliably induced action potentials in cortical neurons and that the µLED probe evoked strong responses in deep neurons. Due to the possibility to integrate many optical stimulation sites onto a single shank, the µLED probe is thus a promising approach to control neurons locally in vivo.

Combined treatment of UVA irradiation and antibiotics induces greater bactericidal effects on Vibrio parahaemolyticus.

Science.gov (United States)

Hou, Yanfei; Nakahashi, Mutsumi; Mawatari, Kazuaki; Shimohata, Takaaki; Uebanso, Takashi; Harada, Yumi; Tsunedomi, Akari; Emoto, Takahiro; Akutagawa, Masatake; Kinouchi, Yohsuke; Takahashi, Akira

2016-01-01

The presence of antibiotics in the environment and their subsequent impact on the development of multi-antibiotic resistant bacteria has raised concerns globally. Consequently, much research is focused on a method to produce a better disinfectant. We have established a disinfectant system using UVA-LED that inactivates pathogenic bacteria. We assessed the bactericidal efficiency of a combination of UVA-LED and antibiotics against Vibrio parahaemolyticus. Combined use of antibiotic drugs and UVA irradiation was more bactericidal than UVA irradiation or antibacterial drugs alone. The bactericidal synergy was observed at low concentrations of each drug that are normally unable to kill the bacteria. This combination has the potential to become a sterilization technology.

Post-irradiation examinations of inert matrix nitride fuel irradiated in JMTR (01F-51A capsule)

International Nuclear Information System (INIS)

Iwai, Takashi; Nakajima, Kunihisa; Kikuchi, Hironobu; Honda, Junichi; Hatakeyama, Yuichi; Ono, Katsuto; Matsui, Hiroki; Arai, Yasuo

2007-03-01

A plutonium nitride fuel pin containing inert matrix such as ZrN and TiN was encapsulated in 01F-51A and irradiated in JMTR. Minor actinides are surrogated by plutonium. Average linear powers and burnups were 408W/cm, 30000MWd/t(Zr+Pu) [132000MWd/t-Pu] for (Zr,Pu)N and 355W/cm, 38000MWd/t(Ti+Pu) [153000MWd/t-Pu] for (TiN,PuN). The irradiated capsule was transported to Reactor Fuel Examination Facility and subjected to non-destructive and destructive post irradiation examinations. Any failure was not observed in the irradiated fuel pin. Very low fission gas release rate of about 1.6% was measured. The inner surface of cladding tube did not show any signs of chemical interaction with fuel pellet. (author)

Effect of irradiation on the properties of some shrinking polymer films

International Nuclear Information System (INIS)

Varsanyi, E.

1974-01-01

Shrinking polymer films (polyethylene, polyvinylidene chloride, polyester) suitable for use in the food industry were studied with the intention to determine the effect of radurizing doses (800 krad and below) on changes in the proportion of crystalline parts in the polymer, and on the tensile strength, elongation at break and shrinkage of the film. Changes in the crystalline/amorphous ratio in the polymer were determined by means of infra-red spectrophotometry. Calculations based on spectral data showed no significant changes in the ratio of crystalline fraction of any of the films, as a function of radurizing doses. Tensile strength and elongation at break tests were carried out by means of standardized instruments and methods. It was found that the tensile strength of the polyethylene film decreased by about 25% as an effect of irradiation, while the same treatment caused no significant changes in the elongation at break. The tensile strength of the polyvinylidene chloride film suffered a decrease of roughly 15%, its elongation at break an about 30% decrease when irradiated. Radiation treatment caused a decrease if less than 10% in tensile strength of the polyester film and a more than 10% change in elongation at break. The tests indicated no significant changes in the shrinkage of radiation treated polymers. The results of the tests led to the conclusion that radurizing doses caused no such change which would affect the applicability of polymer films to the wrapping and packaging of foods subjected to irradiation or would make the films unsuitable for the protection of the goods. (F.J.)

OSL response bleaching of BeO samples, using fluorescent light and blue LEDs

International Nuclear Information System (INIS)

Groppo, Daniela Piai; Caldas, Linda V.E.

2015-01-01

The optically stimulated luminescence (OSL) is widely used as a dosimetric technique for many applications. In this work, the OSL response bleaching of BeO samples was studied. The samples were irradiated using a beta radiation source ( 90 Sr+ 90 Y); the bleaching treatments (fluorescent light and blue LEDs) were performed, and the results were compared. Various optical treatment time intervals were tested until reaching the complete bleaching of the OSL response. The best combination of the time interval and bleaching type was analyzed. (author)

OSL response bleaching of BeO samples, using fluorescent light and blue LEDs

International Nuclear Information System (INIS)

Groppo, D P; Caldas, L V E

2016-01-01

The optically stimulated luminescence (OSL) is widely used as a dosimetric technique for many applications. In this work, the OSL response bleaching of BeO samples was studied. The samples were irradiated using a beta radiation source ("9"0Sr+"9"0Y); the bleaching treatments (fluorescent light and blue LEDs) were performed, and the results were compared. Various optical treatment time intervals were tested until reaching the complete bleaching of the OSL response. The best combination of the time interval and bleaching type was analyzed. (paper)

Method of detecting irradiated pepper

International Nuclear Information System (INIS)

Doumaru, Takaaki; Furuta, Masakazu; Katayama, Tadashi; Toratani, Hirokazu; Takeda, Atsuhiko

1989-01-01

Spices represented by pepper are generally contaminated by microorganisms, and for using them as foodstuffs, some sterilizing treatment is indispensable. However, heating is not suitable to spices, accordingly ethylene oxide gas sterilization has been inevitably carried out, but its carcinogenic property is a problem. Food irradiation is the technology for killing microorganisms and noxious insects which cause the rotting and spoiling of foods and preventing the germination, which is an energy-conserving method without the fear of residual chemicals, therefore, it is most suitable to the sterilization of spices. In the irradiation of lower than 10 kGy, the toxicity test is not required for any food, and the irradiation of spices is permitted in 20 countries. However, in order to establish the international distribution organization for irradiated foods, the PR to consumers and the development of the means of detecting irradiation are the important subjects. The authors used pepper, and examined whether the hydrogen generated by irradiation remains in seeds and it can be detected or not. The experimental method and the results are reported. From the samples without irradiation, hydrogen was scarcely detected. The quantity of hydrogen generated was proportional to dose. The measuring instrument is only a gas chromatograph. (K.I.)

Fish irradiation

International Nuclear Information System (INIS)

Kovacs, J.; Tengumnuay, C.; Juangbhanich, C.

1970-01-01

Chub-mackerel was chosen for the study because they are the most common fish in Thailand. Preliminary investigations were conducted to determine the maximum radiation dose of gamma-rays by organoleptic tests. The samples were subjected to radiation at various doses up to 4 Mrad. Many experiments were conducted using other kinds of fish. The results showed that 1 Mrad would be the maximum acceptable dose for fish. Later, the influence of the radiation dose from 0.1-1 Mrad was studied in order to find the optimum acceptable dose for preservation of fish without off-flavour. For this purpose, the Hedonic scale was used. It was found that 0.2 and 0.5 Mrad gave the best result on Chub mackerel. The determinations of optimum dose, organoleptic, microbiological and trimethylamine content changes were done. The results showed that Chub mackerel irradiated at 0.2, 0.5 and 1 Mrad stored at 3 0 C for 71 days were still acceptable, on the contrary the untreated samples were found unacceptable at 14 days. The trimethylamine increment was significantly higher in the untreated samples. At 15 days storage, trimethylamine in the non-irradiated Chub-mackerel was about 10 times higher than the irradiated ones. At 51 and 79 days storage, about 13 times higher in the control samples than the irradiated samples except 0.1 Mrad. Only 2 times higher was found for the 0.1 Mrad. The microbiological results showed that the irradiation above 0.2 Mrad gave favorable extension of shelf-life of fish

Effect of tumor therapeutic irradiation on the mechanical properties of teeth tissue

International Nuclear Information System (INIS)

Fraenzel, W.; Gerlach, R.; Hein, H.J.; Schaller, H.G.

2006-01-01

Tumor irradiation of the head-neck area is accompanied by the development of a so-called radiation caries in the treated patients. In spite of conservative therapeutic measures, the process results in tooth destruction. The present study investigated the effects of irradiation on the demineralization and remineralization of the dental tissue. For this purpose, retained third molars were prepared and assigned either to a test group, which was exposed to fractional irradiation up to 60 Gy, or to a non-irradiated control group. Irradiated and non-irradiated teeth were then demineralized using acidic hydroxyl-cellulose gel; afterwards the teeth were remineralized using either Bifluorid12 registered or elmex gelee registered . The nanoindentation technique was used to measure the mechanical properties, hardness and elasticity, of the teeth in each of the conditions. The values were compared to the non-irradiated control group. Irradiation decreased dramatically the mechanical parameters of enamel and dentine. In non-irradiated teeth, demineralization had nearly the same effects of irradiation on the mechanical properties. In irradiated teeth, the effects of demineralization were negligible in comparison to non-irradiated teeth. Remineralization with Bifluorid12 registered or elmex gelee registered led to a partial improvement of the mechanical properties of the teeth. The enamel was more positively affected, by remineralization than the dentine. (orig.)

Selective induction of cyclin B protein abrogates the G2 delay after irradiation

International Nuclear Information System (INIS)

Kao, G.; Muschel, R.J.; Maity, A.; Kunig, A.; McKenna, W.G.

1996-01-01

Purpose/Objective: Irradiation of tumor cells commonly results in G2 delay, which has been postulated to allow DNA repair and cell survival. The G2 delay after irradiation is also often marked in some cell lines by delayed expression of cyclin B protein, suggesting a role for cyclin B regulation. Investigations of these hypotheses however has been hampered by the inability to selectively perturb the G2 delay in a physiologic manner. Materials and Methods: We have devised a system, with which we are able to selectively induce cyclin B protein expression in vivo at specific points in the cell cycle, by transfecting Hela cells with an expression vector under control of a dexamethasone-inducible promoter. Experiments were subsequently performed by synchronizing, releasing, irradiating, inducing, and harvesting these cells through the cell cycle. Results: Irradiation with 5 Gy led to a pronounced G2 delay, reflected by markedly slowed progression into mitosis, concomitant with reduced expression of cyclin B protein. Induction of cyclin B after radiation in these cells abrogated the G2 delay by approximately doubling the rate at which the cells re-enter mitosis. Treatment of irradiated untransfected control cells with dexamethasone, in which cyclin B is not induced, led to minimal changes. Studies of effects of cyclin B induction on cyclin B localization (using immunofluorescence), cdc2 phosphorylation and activation will also be presented. Conclusion: This system should allow further investigations into fundamental mechanisms of cell cycle regulation after irradiation and DNA damage. This also provides direct evidence for the first time that cyclin B protein regulation may play a role in the G2 delay following irradiation in Hela cells, perhaps complementing phosphorylation events

Effects of blue diode laser (445 nm) and LED (430-480 nm) radiant heat treatments on dental glass ionomer restoratives

Science.gov (United States)

Dionysopoulos, Dimitrios; Tolidis, Kosmas; Strakas, Dimitrios; Gerasimou, Paris; Sfeikos, Thrasyvoulos; Gutknecht, Norbert

2018-02-01

The purpose of this in vitro study was to evaluate the effect of two radiant heat treatments on water sorption, solubility and surface roughness of three conventional glass ionomer cements by using a blue diode laser (445 nm) and a light emitting diode (LED) unit (430-480 nm). Thirty disk-shaped specimens were prepared for each tested GIC (Equia Fil, Ketac Universal Aplicap and Riva Self Cure). The experimental groups (n = 10) of the study were as follows: Group 1 was the control group, in Group 2 the specimens were irradiated for 60 s at the top surface using a LED light-curing unit and in Group 3 the specimens were irradiated for 60 s at the top surface using a blue light diode laser. Statistical analysis was performed using one-way ANOVA and Tukey post hoc tests at a level of significance of a = 0.05. Radiant heat treatments with both laser and LED devices significantly decreased water sorption and solubility (p tested GICs. Blue diode laser treatment was seemed to be more effective compared to LED treatment for some of the tested materials. There were no changes in surface roughness of the GICs after the treatments (p > 0.05). Among the tested materials there were differences in water sorption and solubility (p 0.05). The use of the blue diode laser for this radiant heat treatment was harmless for the surface of the tested GICs and may be advantageous for the longevity of their restorations.

Effect of irradiation on the malting quality of barley

International Nuclear Information System (INIS)

Avtar, S.; Tejinder, S.; Bains, G.S.

1985-01-01

Two six-row barley cultivars, DL 70 and C164 were subjected to Co 60 gamma irradiation in the range of 0 to 250 Krad and malted with and without gibberellic acid treatment. Barley irradiated with doses up to 75 Krad produced normal malts when compared to the controls. Irradiation doses of 125 and 250 Krad significantly increased the malt yields but considerably decreased the α-amylase activity. Gibberellic acid significantly increased the enzyme activity and degree of modification of the irradiated and the control malts. (author)

Thermal management for LED applications

CERN Document Server

Poppe, András

2014-01-01

Thermal Management for LED Applications provides state-of-the-art information on recent developments in thermal management as it relates to LEDs and LED-based systems and their applications. Coverage begins with an overview of the basics of thermal management including thermal design for LEDs, thermal characterization and testing of LEDs, and issues related to failure mechanisms and reliability and performance in harsh environments. Advances and recent developments in thermal management round out the book with discussions on advances in TIMs (thermal interface materials) for LED applications, advances in forced convection cooling of LEDs, and advances in heat sinks for LED assemblies. This book also: Presents a comprehensive overview of the basics of thermal management as it relates to LEDs and LED-based systems Discusses both design and thermal management considerations when manufacturing LEDs and LED-based systems Covers reliability and performance of LEDs in harsh environments Has a hands-on applications a...

Effects of various kitchen heat treatments, ultraviolet light, and gamma irradiation on mirex insecticide residues in fish

International Nuclear Information System (INIS)

Cin, D.A.; Kroger, M.

1982-01-01

Concentrations of the chlorinated hydrocarbon insecticide mirex (C 10 Cl 12 ) were determined in brown trout from a defined contaminated area of Spring Creek, Centre County, PA, using electron-capture gas chromatography. Conventional heat treatments, namely, baking, frying, poaching, and baking without skin, did not cause significant decreases of the contaminant. Ultraviolet irradiation led to significant reductions (p < 0.05) in mirex concentration in muscle tissue. Exposures of 24, 48, and 72 hr led to degradations of 30.0%, and 45.6%, respectively, of the initial mirex concentration. Gamma irradiation also led to significant reductions (p < 0.05) in mirex concentration in muscle tissue. Following absorption of 1, 3, and 5 Mrad, degradations of 9.8%, 23,1%, and 37.5%, respectively, of the initial mirex concentration were observed

Detecting irradiation of strawberries by means of thermoluminescence measurement

International Nuclear Information System (INIS)

Heide, L.; Guggenberger, R.; Boegl, K.W.

1989-01-01

Investigations into the origin of the thermoluminescence (TL) have shown that this effect is due to trace amounts of mineral particulates adhering to the irradiated material. This result and own experience have led to the development of the TL-based method for post-factum detection of an irradiation of strawberries. In addition to the analysis of whole fruits, a method has been tested that proceeds via separation of adhering matter to separate TL analysis of the particulates. The results obtained so far show no difference or improvement as compared to whole-fruit TL analysis. (orig./MG) [de

Effect of 710 nm visible light irradiation on neurite outgrowth in primary rat cortical neurons following ischemic insult

Energy Technology Data Exchange (ETDEWEB)

Choi, Dong-Hee [Center for Neuroscience Research, SMART Institute of Advanced Biomedical Science, Konkuk University, Seoul (Korea, Republic of); Department of Medical Science, Konkuk University School of Medicine, Seoul (Korea, Republic of); Lee, Kyoung-Hee; Kim, Ji-Hye; Kim, Moon Young [Center for Neuroscience Research, SMART Institute of Advanced Biomedical Science, Konkuk University, Seoul (Korea, Republic of); Lim, Jeong Hoon [Department of Rehabilitation Medicine, Konkuk University School of Medicine, Seoul (Korea, Republic of); Rehabilitation Medicine, Division of Neurology, Department of Medicine, National University Hospital, National University Health System (Singapore); Lee, Jongmin, E-mail: leej@kuh.ac.kr [Center for Neuroscience Research, SMART Institute of Advanced Biomedical Science, Konkuk University, Seoul (Korea, Republic of); Department of Rehabilitation Medicine, Konkuk University School of Medicine, Seoul (Korea, Republic of)

2012-06-01

Highlights: Black-Right-Pointing-Pointer 710 nm wavelength light (LED) has a protective effect in the stroke animal model. Black-Right-Pointing-Pointer We determined the effects of LED irradiation in vitro stroke model. Black-Right-Pointing-Pointer LED treatment promotes the neurite outgrowth through MAPK activation. Black-Right-Pointing-Pointer The level of synaptic markers significantly increased with LED treatment. Black-Right-Pointing-Pointer LED treatment protects cell death in the in vitro stroke model. -- Abstract: Objective: We previously reported that 710 nm Light-emitting Diode (LED) has a protective effect through cellular immunity activation in the stroke animal model. However, whether LED directly protects neurons suffering from neurodegeneration was entirely unknown. Therefore, we sought to determine the effects of 710 nm visible light irradiation on neuronal protection and neuronal outgrowth in an in vitro stroke model. Materials and methods: Primary cultured rat cortical neurons were exposed to oxygen-glucose deprivation (OGD) and reoxygenation and normal conditions. An LED array with a peak wavelength of 710 nm was placed beneath the covered culture dishes with the room light turned off and were irradiated accordingly. LED treatments (4 min at 4 J/cm{sup 2} and 50 mW/cm{sup 2}) were given once to four times within 8 h at 2 h intervals for 7 days. Mean neurite density, mean neurite diameter, and total fiber length were also measured after microtubule associated protein 2 (MAP2) immunostaining using the Axio Vision program. Synaptic marker expression and MAPK activation were confirmed by Western blotting. Results: Images captured after MAP2 immunocytochemistry showed significant (p < 0.05) enhancement of post-ischemic neurite outgrowth with LED treatment once and twice a day. MAPK activation was enhanced by LED treatment in both OGD-exposed and normal cells. The levels of synaptic markers such as PSD 95, GAP 43, and synaptophysin significantly

CooLED - efficient LED bulbs with custrom optics - final report

DEFF Research Database (Denmark)

Wolff, Jesper; Corell, Dennis Dan; Dam-Hansen, Carsten

Denne rapport indeholder en beskrivelse af arbejdet udført i og resultaterne af forsknings- og udviklingsprojektet EUDP 64012-0226, CooLED – en ny generation LED Lyskilde for det tidsløse high-end marked....

Experience with LEDS and NAMA Low Carbon Strategies: The Case of Georgia

Directory of Open Access Journals (Sweden)

Kakhaberi Mdivani

2016-06-01

Full Text Available Low Emission Development Strategies (LEDS and National Appropriate Mitigation Actions (NAMAs have the potential to support developing countries in attaining low carbon goals. In spite of the evident potential, there is a need to learn from practice. This paper explores the case of Georgia. The main research question discussed is: What experience has been gained with the development of LEDS and NAMAs in Georgia? The study reveals that both LEDS and NAMAs are subject to barriers that considerably slow development processes: there is a lack of institutional capacity, little inter-governmental goal alignment and poor coordination of actions, a lack of experienced staff and insufficient, substantial, earmarked funding. Capacity building depends on support from organizations in donor countries. This paper contributes to a growing body of knowledge of the implementation of LEDS and NAMA.

Irradiation of fruits for quarantine insect disinfestation. Development in the world and in France

International Nuclear Information System (INIS)

Buscarlet, L.A.

1990-01-01

In many countries strict phytosanitary controls have been established to prevent the entry of foreign insect species. The recent interdiction of ethylene dibromide fumigation in USA led to the search of new methods of quarantine control among which irradiation was considered as the more convenient. In different countries such as USA, Australia, New Zeland, studies were conducted to determine the dose of irradiation efficient for controlling different insect species and to verify that irradiation had no noxious effect on the fruits. At the present time the papaya harvested in Hawaii and irradiated against fruit flies are allowed to enter in the continent of USA. In France the irradiation of apples against Leucoptera malifoliella is under study to promote the exportation of apples to America [fr

Chemical reactions induced by fast neutron irradiation

International Nuclear Information System (INIS)

Katsumura, Y.

1989-01-01

Here, several studies on fast neutron irradiation effects carried out at the reactor 'YAYOI' are presented. Some indicate a significant difference in the effect from those by γ-ray irradiation but others do not, and the difference changes from subject to subject which we observed. In general, chemical reactions induced by fast neutron irradiation expand in space and time, and there are many aspects. In the time region just after the deposition of neutron energy in the system, intermediates are formed densely and locally reflecting high LET of fast neutrons and, with time, successive reactions proceed parallel to dissipation of localized energy and to diffusion of the intermediates. Finally the reactions are completed in longer time region. If we pick up the effects which reserve the locality of the initial processes, a significant different effect between in fast neutron radiolysis and in γ-ray radiolysis would be derived. If we observe the products generated after dissipation and diffusion in longer time region, a clear difference would not be observed. Therefore, in order to understand the fast neutron irradiation effects, it is necessary to know the fundamental processes of the reactions induced by radiations. (author)

Isolation of Enterobacter cowanii in tomatoes after gamma irradiation

International Nuclear Information System (INIS)

Vicalvi, M.C.V.; Solidonio, E.G.; Silva, M.A.; Colaco, W.; Silva, G.R. da; Sena, K.X.F.R de

2013-01-01

The tomato is one of the most consumed fruit in the world. Bacteria of the family Enterobacteriaceae are responsible for large outbreaks of gastroenteritis. Irradiation is a physical method which reduces waste by eliminating spoilage organisms in foods. The objective of this study was to identify and determine the resistance profile of micro-organisms of the family Enterobacteriaceae from irradiated tomatoes. Were used three batches each containing 80 tomatoes, and divided in control and irradiated. The samples were individually properly identified as the irradiation dose applied. The material was subjected to irradiation with gamma rays, for irradiating with a cobalt-60 source, using doses: 1.0, 1.5 and 2 kGy (6,060 kGy/h). For microbiological analysis tomatoes were cut out, and removing the shells to obtain samples weighing 25g. Each sample was transferred to an Erlenmeyer containing sterilized water, stirring the assembly mechanically. Aliquots of the wash waters were sown in differential and selective media. After reisolation, the colonies were subjected to Gram staining then performed biochemical tests for identification. The antibiotic susceptibility tests were performed according to CLSI (Clinical Laboratory Standard Institute). It was isolated three strains of Enterobacter cowanii in tomato samples irradiated with a dose of 1.0 kGy, without isolating the other doses. As for the resistance profile, the strains were resistant to Ampicillin identified. Gamma irradiation at a dose of 1.5 and 2 kGy was effective in tomatoes as well as the micro-organism isolated after irradiation showed no profile of multidrug resistance. (author)

Demonstration Assessment of LED Roadway Lighting: Philadelphia, PA

Energy Technology Data Exchange (ETDEWEB)

Royer, Michael P.; Tuenge, Jason R.; Poplawski, Michael E.

2012-09-01

For this demonstration assessment, 10 different groups of LED luminaires were installed at three sites in Philadelphia, PA. Each of the three sites represented a different set of conditions, most importantly with regard to the incumbent HPS luminaires, which were nominally 100 W, 150 W, and 250 W. The performance of each product was evaluated based on manufacturer data, illuminance calculations, field measurements of illuminance, and the subjective impressions of both regular and expert observers.

Radiometric analysis of UV to near infrared LEDs for optical sensing and radiometric measurements in photochemical systems

Czech Academy of Sciences Publication Activity Database

Noori, A.; Mahbub, P.; Dvořák, Miloš; Lucieer, A.; Macka, M.

Roč. 262, JUN ( 2018 ), s. 171-179 ISSN 0925-4005 Institutional support: RVO:68081715 Keywords : light emitting diodes (LEDs) * optical sensing * LED characterisation Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 5.401, year: 2016

Radiometric analysis of UV to near infrared LEDs for optical sensing and radiometric measurements in photochemical systems

Czech Academy of Sciences Publication Activity Database

Noori, A.; Mahbub, P.; Dvořák, Miloš; Lucieer, A.; Macka, M.

2018-01-01

Roč. 262, JUN (2018), s. 171-179 ISSN 0925-4005 Institutional support: RVO:68081715 Keywords : light emitting diodes ( LED s) * optical sensing * LED characterisation Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 5.401, year: 2016

Are nurse-led chemotherapy clinics really nurse-led? An ethnographic study.

Science.gov (United States)

Farrell, Carole; Walshe, Catherine; Molassiotis, Alex

2017-04-01

The number of patients requiring ambulatory chemotherapy is increasing year on year, creating problems with capacity in outpatient clinics and chemotherapy units. Although nurse-led chemotherapy clinics have been set up to address this, there is a lack of evaluation of their effectiveness. Despite a rapid expansion in the development of nursing roles and responsibilities in oncology, there is little understanding of the operational aspects of nurses' roles in nurse-led clinics. To explore nurses' roles within nurse-led chemotherapy clinics. A focused ethnographic study of nurses' roles in nurse-led chemotherapy clinics, including semi-structured interviews with nurses. Four chemotherapy units/cancer centres in the UK PARTICIPANTS: Purposive sampling was used to select four cancer centres/units in different geographical areas within the UK operating nurse-led chemotherapy clinics. Participants were 13 nurses working within nurse-led chemotherapy clinics at the chosen locations. Non-participant observation of nurse-led chemotherapy clinics, semi-structured interviews with nurse participants, review of clinic protocols and associated documentation. 61 nurse-patient consultations were observed with 13 nurses; of these 13, interviews were conducted with 11 nurses. Despite similarities in clinical skills training and prescribing, there were great disparities between clinics run by chemotherapy nurses and those run by advanced nurse practitioners. This included the number of patients seen within each clinic, operational aspects, nurses' autonomy, scope of practice and clinical decision-making abilities. The differences highlighted four different levels of nurse-led chemotherapy clinics, based on nurses' autonomy and scope of clinical practice. However, this was heavily influenced by medical consultants. Several nurses perceived they were undertaking holistic assessments, however they were using medical models/consultation styles, indicating medicalization of nurses' roles

Discrete ordinates solution of coupled conductive radiative heat transfer in a two-layer slab with Fresnel interfaces subject to diffuse and obliquely collimated irradiation

International Nuclear Information System (INIS)

Muresan, Cristian; Vaillon, Rodolphe; Menezo, Christophe; Morlot, Rodolphe

2004-01-01

The coupled conductive radiative heat transfer in a two-layer slab with Fresnel interfaces subject to diffuse and obliquely collimated irradiation is solved. The collimated and diffuse components problems are treated separately. The solution for diffuse radiation is obtained by using a composite discrete ordinates method and includes the development of adaptive directional quadratures to overcome the difficulties usually encountered at the interfaces. The complete radiation numerical model is validated against the predictions obtained by using the Monte Carlo method

Characterization of curing behavior of UV-curable LSR for LED embedded injection mold

Science.gov (United States)

Tae, Joon-Sung; Yim, Kyung-Gyu; Rhee, Byung-Ohk; Kwak, Jae B.

2016-11-01

For many applications, liquid silicone rubber (LSR) injection molding is widely used for their great design flexibility and high productivity. In particular, a sealing part for a mobile device such as smartphone and watch has been produced by injection molding. While thermally curable LSR causes deformation problem due to a high mold temperature, UV-curable LSR can be molded at room temperature, which has advantages for over-molding with inserts of temperature-sensitive materials. Ultraviolet light-emitting diodes (UV LEDs) have advantages such as a longer service life, a lower heat dissipation, and smaller size to equip into the mold than conventional halogen or mercury UV lamps. In this work, rheological behavior of UV-curable LSR during curing process was analyzed by UV LEDs available in the market. UV-LEDs of various wave lengths and intensities were tested. The steady shear test was applied to find the starting time of curing and the SAOS was applied to find the ending time of curing to estimate processing time. In addition, the hardness change with irradiation energy was compared with the rheological data to confirm the reliability of the rheological test.

Final report LED solutions for public lighting; Eindrapportage LED oplossingen voor openbare verlichting

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-04-15

This report examines if and how LED can be used for public lighting on a large scale. Pilot projects in 29 municipalities were assessed to test the usefulness of LED lighting. This final report provides answers to the questions that relate to the feasibility of the deployment of LED in public lighting and provides some practical pointers. [Dutch] Er is onderzocht of, en zo ja op welke wijze, LED grootschalig toegepast kan worden in de openbare verlichting (OVL). In 29 gemeenten in Nederland zijn proefprojecten geevalueerd om LED verlichting te toetsen op bruikbaarheid. Deze eindrapportage geeft antwoord op vragen die betrekking hebben op de haalbaarheid van de toepassing van LED binnen de OVL en geeft wat praktische aandachtspunten.

The kinetics of formation and transformation of silver atoms on solid surfaces subjected to ionizing irradiation

International Nuclear Information System (INIS)

Popovich, G.M.

1988-01-01

The paper discusses the results obtained in ESR-assisted studies of the kinetics of formation and transformation of silver atoms generated by γ-irradiation of silver-containing carriers. Three types of dependences have been established: (1) extreme; (2) saturation curves and (3) step-like. All the kinetic curves display, after a definite period of time, stable concentrations of adsorbed silver atoms per unit of the surface at a given temperature. Depending on the temperature of the experiment, the composition and nature of the carrier, the number of adsorbed silver ions, the irradiation dose and conditions of the experiment, a stable concentration of silver atoms at a given temperature may be equal to, higher or lower than the number of silver atoms measured immediately after γ-irradiation at a temperature of liquid nitrogen. A kinetic scheme is proposed to explain the obtained curves. The model suggests that the silver atoms adsorbed on the surface, as well as those formed after γ-irradiation, are bonded to the surface by various energies, which are related to heterogeneity of the carrier surface. (author)

Neutron Dosimetry and Irradiation of Solids; Dosimetrie des neutrons et irradiation des solides

Energy Technology Data Exchange (ETDEWEB)

Perriot, G; Schmitt, A P [Commissariat a l' Energie Atomique. Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France)

1962-07-01

Results of work at C.E.A. from 1958 to 1960 are reviewed. The possibilities offered by classical dosimetry methods are discussed. The tests which led to the utilization, for fast neutron dosimetry, of resistivity variations induced in solid W by such neutrons are described. Experimental W irradiation results led to a definition of neutron efficiency which describes the relations between neutron energy and their effects on materials. Possibilities offered by detectors which make use of radiation damage and are sensitive to neutrons at keV energies were explored. In other work, the principal French reactors were classified according to their ability to produce damage in materials such as W. (authors) [French] Dans ce rapport on a presente les resultats essentiels de travaux qui ont ete effectues de 1958 a 1980 par des chercheurs du CEA issus de differents services. En meme temps qu'une revue des possibilites offertes a l'epoque par les methodes classiques de dosimetrie (utilisation des detecteurs par activation), on a decrit les essais qui devaient permettre d'utiliser, a la dosimetrie les neutrons rapides, les variations de resistivite qu'ils creent dans un corps solide (tungstene). L'irradiation du tungstene a montre l'importance qu'il y avait a definir 'l'efficacite' des neutrons, c'est-a-dire leur aptitude plus ou moins grande, selon leur energie, a creer des defauts dans les materiaux. L'efficacite d'un emplacement d'irradiation se trouvant liee au spectre neutronique, on a vu les difficultes qu'il y avait a utiliser les detecteurs par activation des qu'on n'avait plus affaire a un spectre en 1/E ou de fission et on a pu entrevoir les possibilites offertes par les detecteurs utilisant la creation des defauts qui repondent a tous les neutrons d'energies, superieures a quelques keV. Enfin, on a classe les principaux types de Piles Francaises selon leur aptitude a creer plus ou moins rapidement des dommages dans des materiaux comme le tungstene. (auteur)

The effect of gamma radiation on the rice moth, Corcyra Cephalonica (Staint). Part II irradiation of the eggs, pupae, and adults

Energy Technology Data Exchange (ETDEWEB)

Loaharanu, S; Sutantawong, M; Ungsunanatwiwat, A

1972-12-31

The 1-3 days old eggs of the rice moth were exposed to gamma rays at 0, 3, 6, 12.5 and 25 krads. The LD{sub 50} and LD{sub 99} for eggs was estimated as 9 and 42 krads respectively. A dose of 25 krads caused 100% mortality in larvae irradiated as egg stage. Mixed ages of 1-7 days old pupae were subjected to 0, 6, 12.5, 25, 50 and 100 Krads of gamma rays. Based on number of adults emerged, the LD{sub 50} and LD{sub 99} for pupae were estimated as 19 and 110 krads. Mixed sexes of 1-3 days old adult moths were also exposed to gamma rays. The LD{sub 50} and LD{sub 99} for adults appeared to be 60 and 170 krads respectively. Irradiation of both sexes of adult moths at 25 and 50 krads, led to complete infertility in eggs deposited.

Swelling in cold-worked 316 stainless steels irradiated in a PWR

Energy Technology Data Exchange (ETDEWEB)

Fukuya, Koji; Fujii, Katsuhiko [Institute of Nuclear Safety System Inc., Mihama, Fukui (Japan)

2001-09-01

Swelling behavior in a cold-worked 316 stainless steel irradiated up to 53 dpa in a PWR at 290-320degC was examined using high resolution transmission electron microscopy. Small cavities with the average diameter of 1 nm were observed in the samples irradiated to doses above 3 dpa. The average diameter did not increase with increasing in dose. The maximum swelling was as low as 0.042%. The measured helium content and the cavity morphology led to the conclusion that the cavities were helium bubbles. A comparison of the observed cavity microstructure with data from FBR, HFIR and ATR irradiation showed that the cavity structure in PWR at 320degC or less was similar to those in HFIR and ATR irradiation but quite different from those in FBR condition. From a calculation based on the cavity data and kinetic models the incubation dose of swelling was estimated to be higher than 80dpa in the present irradiation condition. (author)

GRAIN-BOUNDARY PRECIPITATION UNDER IRRADIATION IN DILUTE BINARY ALLOYS

Institute of Scientific and Technical Information of China (English)

S.H. Song; Z.X. Yuan; J. Liu; R.G.Faulkner

2003-01-01

Irradiation-induced grain boundary segregation of solute atoms frequently bring about grain boundary precipitation of a second phase because of its making the solubility limit of the solute surpassed at grain boundaries. Until now the kinetic models for irradiation-induced grain boundary precipitation have been sparse. For this reason, we have theoretically treated grain boundary precipitation under irradiation in dilute binary alloys. Predictions ofγ'-Ni3Si precipitation at grain boundaries ave made for a dilute Ni-Si alloy subjected to irradiation. It is demonstrated that grain boundary silicon segregation under irradiation may lead to grain boundaryγ'-Ni3 Si precipitation over a certain temperature range.

An investigation of high-temperature irradiation test program of new ceramic materials

International Nuclear Information System (INIS)

Ishino, Shiori; Terai, Takayuki; Oku, Tatsuo

1999-08-01

The Japan Atomic Energy Research Institute entrusted the Atomic Energy Society of Japan with an investigation into the trend of irradiation processing/damage research on new ceramic materials. The present report describes the result of the investigation, which was aimed at effective execution of irradiation programs using the High Temperature Engineering Test Reactor (HTTR) by examining preferential research subjects and their concrete research methods. Objects of the investigation were currently on-going preliminary tests of functional materials (high-temperature oxide superconductor and high-temperature semiconductor) and structural materials (carbon/carbon and SiC/SiC composite materials), together with newly proposed subjects of, e.g., radiation effects on ceramics-coated materials and super-plastic ceramic materials as well as microscopic computer simulation of deformation and fracture of ceramics. These works have revealed 1) the background of each research subject, 2) its objective and significance from viewpoints of science and engineering, 3) research methodology in stages from preliminary tests to real HTTR irradiation, and 4) concrete HTTR-irradiation methods which include main specifications of test specimens, irradiation facilities and post-irradiation examination facilities and apparatuses. The present efforts have constructed the important fundamentals in the new ceramic materials field for further planning and execution of the innovative basic research on high-temperature engineering. (author)

User evaluation of eight led light sources with different special colour rendering indices R9

DEFF Research Database (Denmark)

Markvart, Jakob; Iversen, Anne; Logadottir, Asta

2013-01-01

In this study we evaluated the influence of the special colour rendering index R9 on subjective red colour perception and Caucasian skin appearance among untrained test subjects. The light sources tested are commercially available LED based light sources with similar correlated colour temperature...

Examination of the LED Source in Traffic Lights and the Effect of Airborne Dirt on its Performance

Directory of Open Access Journals (Sweden)

Amela Softić

2017-05-01

Full Text Available The performed evaluation consisted of two phases: measurement of the illumination levels of (new LED system and carrying out the public opinion poll on the subjective visual performance of LED in traffic lights. The results of the measured levels of illumination show that deposition of dirt considerably affects its values. The survey results confirm an overall positive impression on LED performances in traffic lights.

Food irradiation - Problems and promises

International Nuclear Information System (INIS)

Hickman, J.R.

1974-01-01

It has been stated that food irradiation represents the most significant discovery in food processing since Nicholas Appert invented canning in 1810. Certainly it is a process with great future potential; it is attractive because it works without heating the product, it is effective within sealed containers as well as for bulk usage, and it does not leave chemical residues on the treated food. Of course, no one process can be expected to solve all problems relating to preservation of food. Ionizing radiation can be used effectively to solve many of these problems, but the process is no panacea to cure the world's food problems. Unfortunately, early ill-founded claims about irradiation led to expectations which have proved beyond the reasonable capabilities of the process. Nevertheless, the number of foods that have been successfully treated, and the broad range of effects that can be achieved by radiation processing is impressive. (author)

LED-roulette : LED's vervangen balletje

NARCIS (Netherlands)

Goossens, P.

2007-01-01

Iedereen waagt wel eens een gokje, in een loterij of misschien ook in een casino. Wie droomt er immers niet van om op een gemakkelijke manier rijk te worden? Met de hier beschreven LED-roulette valt weliswaar weinig te winnen, maar het is wel een uitstekende manier om het roulettespel thuis te

Safety factors influencing the acceptance of food irradiation technology

International Nuclear Information System (INIS)

1989-01-01

The International Consultative Group on Food Irradiation convened a Task Force Meeting on Public Information of Food Irradiation at the French Commissariat a l'Energie Atomique (CEA), Cadarache from 18 to 21 April 1988. A compilation of scientific papers on subjects of public interest on food irradiation was made by internationally-recognized experts. The report of the meeting and the review papers presented at the meeting are included in this publication. Refs, figs and tabs

Inactivation of Lactobacillus plantarum by pulsed-microwave irradiation

International Nuclear Information System (INIS)

Shin, J.K.; Pyun, Y.R.

1997-01-01

Suspensions of Lactobacillus plantarum cells were subjected to either conventional heating, continuous microwave (CW) or pulsed microwave (PW) irradiation at 50 degrees C for 30 min. Samples exposed to PW showed greater reductions (2 approximately 4 log) in survival counts than those treated with either conventional heating or CW irradiation. As exposure time increased, PW resulted in a remarkable increase in 260 nm-absorbing compounds that leaked into the suspending menstruum, as compared to CW or conventional heating, indicating that PW irradiated cells were the most injured. The growth of PW irradiated cells was delayed about 24h and the final acidity of the culture broth was about 60 approximately 80% that of other cells treated with conventional heating or CW irradiation

Effects of light emitting diode irradiation on neural differentiation of human umbilical cord-derived mesenchymal cells.

Science.gov (United States)

Dehghani-Soltani, Samereh; Shojaee, Mohammad; Jalalkamali, Mahshid; Babaee, Abdolreza; Nematollahi-Mahani, Seyed Noureddin

2017-08-30

Recently, light emitting diodes (LEDs) have been introduced as a potential physical factor for proliferation and differentiation of various stem cells. Among the mesenchymal stem cells human umbilical cord matrix-derived mesenchymal (hUCM) cells are easily propagated in the laboratory and their low immunogenicity make them more appropriate for regenerative medicine procedures. We aimed at this study to evaluate the effect of red and green light emitted from LED on the neural lineage differentiation of hUCM cells in the presence or absence of retinoic acid (RA). Harvested hUCM cells exhibited mesenchymal and stemness properties. Irradiation of these cells by green and red LED with or without RA pre-treatment successfully differentiated them into neural lineage when the morphology of the induced cells, gene expression pattern (nestin, β-tubulin III and Olig2) and protein synthesis (anti-nestin, anti-β-tubulin III, anti-GFAP and anti-O4 antibodies) was evaluated. These data point for the first time to the fact that LED irradiation and optogenetic technology may be applied for neural differentiation and neuronal repair in regenerative medicine.

Effects of light emitting diode (LED) therapy and cold water immersion therapy on exercise-induced muscle damage in rats.

Science.gov (United States)

Camargo, Mariana Zingari; Siqueira, Cláudia Patrícia Cardoso Martins; Preti, Maria Carla Perozim; Nakamura, Fábio Yuzo; de Lima, Franciele Mendes; Dias, Ivan Frederico Lupiano; Toginho Filho, Dari de Oliveira; Ramos, Solange de Paula

2012-09-01

The aim of this work is to analyze the effects of LED therapy at 940 nm or cold water immersion therapy (CWI) after an acute bout of exercise on markers of muscle damage and inflammation. Thirty-two male Wistar rats were allocated into four groups: animals kept at rest (control), exercised animals (E), exercised + CWI (CWI), and exercised + LED therapy (LED). The animals swam for 100 min, after which blood samples were collected for lactate analysis. Animals in the E group were returned to their cages without treatment, the CWI group was placed in cold water (10°C) for 10 min and the LED group received LED irradiation on both gastrocnemius muscles (4 J/cm(2) each). After 24 h, the animals were killed and the soleus muscles were submitted to histological analysis. Blood samples were used for hematological and CK analyses. The results demonstrated that the LED group presented fewer areas of muscle damage and inflammatory cell infiltration and lower levels of CK activity than the E group. Fewer areas of damaged muscle fiber were observed in the LED group than in CWI. CWI and LED did not reduce edema areas. Hematological analysis showed no significant effect of either treatment on leukocyte counts. The results suggest that LED therapy is more efficient than CWI in preventing muscle damage and local inflammation after exercise.

Combined effect of carcinogenic n-nitrosodimethylamine precursors and fractioned γ-irradiation on tumor development in rats

International Nuclear Information System (INIS)

Galenko, P.M.; Nedopitanskaya, N.N.

1996-01-01

The influence of combined action of N-nitrosodimethylamine (NDMA) and fractioned γ-irradiation on tumor development in rats was investigated. Both the tumor frequency and tumor plurality coefficient have been studied for two types of treatment: precursors of NDMA (amidopyrine and/or sodium nitrite (SN)) alone and the combination 'precursors plus radiation'. Tumor frequency decreased by about 11% after combination of γ-irradiation and precursors in comparison with precursors alone. Nevertheless, treatment with SN and γ-irradiation did not change tumor frequency in comparison with SN alone. Irradiation of rats treated with precursors led to an increased tumor plurality coefficient

Industrial irradiators and their radioprotection

Energy Technology Data Exchange (ETDEWEB)

Rodrigues Junior, Ary de Araujo (ed.)

2018-04-01

In this book you will learn how the gamma irradiators and accelerators for industry and research applications work and all the radioprotection safety items that should be followed when operating them. This book was written mainly for those who intend to become Radiation Safety Officers (RSO) responsible for the operation of gamma irradiators, but it is also useful to business people who plan to embark on this area or for those who are simply curious. This book is only an introduction to the subject and is far from being exhaustive. (author)

Facts about food irradiation. A series of fact sheets from the International Consultative Group on Food Irradiation

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-12-01

The safety and benefits of foods processed by ionizing radiation are well documented. In an effort to provide governments, especially those of developing countries, with scientifically accurate information on issues of general interest to the public, the International Consultative Group on Food Irradiation (ICGFI), which was established under the aegis of the Food and Agriculture Organization of the United Nations (FAO), the World Health Organization (WHO), and the IAEA, decided at its 7th Annual Meeting in Rome, Italy, on October 1990, to issue a series of ''Fact Sheets'' on the subject. ICGFI, an inter-governmental body with a membership of 37 governments, has as one of its mandates the function to provide information to Member States of the FAO, WHO, and IAEA and to the three organizations themselves on the safe and proper use of food irradiation technology. The Fact Sheets included here cover issues relating to: status and trends; scientific and technical terms; food irradiation and radioactivity; chemical changes in irradiated food; nutritional quality of irradiated foods; genetic studies; microbiological safety of irradiated food; irradiation and food safety; irradiation and food additives and residues; packaging of irradiated foods; safety of irradiation facilities; controlling the process; food irradiation costs; and irradiated foods and the consumer. The Fact Sheets have been separately indexed and included in the INIS Database under Reference Numbers 23011206-23011217, 23011319 and 23012743. The Fact Sheets were first issued by the ICGFI Secretariat (Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture, Vienna, Austria) in May 1991.

Facts about food irradiation. A series of fact sheets from the International Consultative Group on Food Irradiation

International Nuclear Information System (INIS)

1991-12-01

The safety and benefits of foods processed by ionizing radiation are well documented. In an effort to provide governments, especially those of developing countries, with scientifically accurate information on issues of general interest to the public, the International Consultative Group on Food Irradiation (ICGFI), which was established under the aegis of the Food and Agriculture Organization of the United Nations (FAO), the World Health Organization (WHO), and the IAEA, decided at its 7th Annual Meeting in Rome, Italy, on October 1990, to issue a series of ''Fact Sheets'' on the subject. ICGFI, an inter-governmental body with a membership of 37 governments, has as one of its mandates the function to provide information to Member States of the FAO, WHO, and IAEA and to the three organizations themselves on the safe and proper use of food irradiation technology. The Fact Sheets included here cover issues relating to: status and trends; scientific and technical terms; food irradiation and radioactivity; chemical changes in irradiated food; nutritional quality of irradiated foods; genetic studies; microbiological safety of irradiated food; irradiation and food safety; irradiation and food additives and residues; packaging of irradiated foods; safety of irradiation facilities; controlling the process; food irradiation costs; and irradiated foods and the consumer. The Fact Sheets have been separately indexed and included in the INIS Database under Reference Numbers 23011206-23011217, 23011319 and 23012743. The Fact Sheets were first issued by the ICGFI Secretariat (Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture, Vienna, Austria) in May 1991

Effects of irradiation of sewage sludge on heavy metal bioavailability

International Nuclear Information System (INIS)

Sheppard, S.C.; Mayoh, K.R.

1986-10-01

Sewage sludges are a valuable resource to agriculture, but their use is limited by the hazards of pathogens, toxic chemicals and heavy metals. Irradiation can control the pathogens and deactivate some of the toxic chemicals. The relative cost of industrial-scale irradiation using accelerators has decreased progressively. This, coupled with the increasing necessity to recycle wastes, has led to renewed interest in irradiation of sludges. In response to this renewed interest, this report examines what is known about the effects of irradiation on the bioavailability of heavy metals. Very few studies have addressed this topic, although workers in the U.S. have claimed decreased solubility of metals in irradiated sludges. We have also briefly reviewed the general literature on sludge to gain indirect evidence on the likely effects. The scant data, often based on less than ideal experimental methodologies, show no major consistent effects of irradiation on the availability of heavy metals from sludge. The data are not sufficient to rule out such effects entirely, but the effects appear to be fairly subtle and not likely to persist beyond one growth season. 85 refs

Detection of irradiation treatment of foods using DNA 'comet assay'

International Nuclear Information System (INIS)

Khan, Hasan M.; Delincee, Henry

1998-01-01

Microgel electrophoresis of single cells (DNA comet assay) has been investigated to detect irradiation treatment of some food samples. These samples of fresh and frozen rainbow trout, red lentil, gram and sliced almonds were irradiated to 1 or 2 kGy using 10 MeV electron beam from a linear accelerator. Rainbow trout samples yielded good results with samples irradiated to 1 or 2 kGy showing fragmentation of DNA and, therefore, longer comets with no intact cells. Unirradiated samples showed shorter comets with a significant number of intact cells. For rainbow trout stored in a freezer for 11 days the irradiated samples can still be discerned by electrophoresis from unirradiated samples, however, the unirradiated trouts also showed some longer comets besides some intact cells. Radiation treatment of red lentils can also be detected by this method, i.e. no intact cells in 1 or 2 kGy irradiated samples and shorter comets and some intact cells in unirradiated samples. However, the results for gram and sliced almond samples were not satisfactory since some intact DNA cells were observed in irradiated samples as well. Probably, incomplete lysis has led to these deviating results

New illuminations approaches with single-use micro LEDs endoilluminators for the pars plana vitrectomy

Science.gov (United States)

Koelbl, Philipp Simon; Koch, Frank H. J.; Lingenfelder, Christian; Hessling, Martin

2018-02-01

The illumination of the intraocular space during pars plana vitrectomy always bears the risk of retina damage by irradiation. Conventional illumination systems consist of an external light source and an optical fiber to transfer the visible light (radiation) into the eye. Often xenon arc and halogen lamps are employed for this application with some disadvantageous properties like high phototoxicity and low efficiency. Therefore, we propose to generate the light directly within the eye by inserting a white micro LED with a diameter of 0.6 mm. The LED offers a luminous flux of 0.6 lm of white light with a blue peak @ 450 nm and a yellow peak @ 555 nm. The presented prototypes fit through a standard 23 G trocar and are the first intraocular light sources worldwide. Two different single-use approaches have already been developed: a handguided and a chandelier device. The hand-guided applicator enables a directly navigation and illumination up to a working distance of 6 mm. The chandelier device is much smaller and does not need an active navigation of the light cone. The brightness and homogeneity of the illumination of these LED devices have been successfully tested on porcine eyes. Presented measurements and calculations prove that even for high LED currents and small distances to the retina these intraocular micro LED devices expose the retina to less hazard than conventional illumination sources like fiber based xenon systems. Even under the worst circumstances application durations of 180 hours would be justifiable.

Features of aseptic granulomatous imflammation in rats subjected to the chronic action of gamma irradiation in small doses

Energy Technology Data Exchange (ETDEWEB)

Goranov, I; Krushkov, I; Statelov, V; Bratanov, M; Nacheva, V; Gospodinova, D; Serafimov, A

1976-04-01

Wistar rats were given a Co-60 dose of 2 r/day over a period of 8 months, or a total dose of 400 r. Two sterile sponge scraps of the same size and form were introduced subcutaneously into the intracapsular space of rats in the control and irradiated groups. Cuts were made in the subcutaneous tissue near the implanted foreign bodies. A vigorous inflammatory reaction developed in the unirradiated animals. The skin granulated normally. The irradiated animals showed a general bleeding of the tissues at the implantation site. A number of deviations were noted during the tissue granulation of the irradiated rats. The migration of leucocytes into the infected site was decreased. The formation of macrophage elements and their activity was lower in the irradiated animals. The reaction of the connective tissue turned out to be a rather sensitive test of the disruptive effects of long-term irradiation. 11 refs.

Study on silk yellowing induced by gamma-irradiation

International Nuclear Information System (INIS)

Tsukada, Masuhiro; Aoki, Akira

1985-01-01

The changes in the yellow color of silk threads with total dose of irradiation applied were described and studied by a colorimetric method and by monochrome photography. The change into a yellow color of the specimen in the course of irradiation was clearly detected in photographs using filters, 2B and SC 56 under light conditions at the wavelength of 366 nm. The b/L value measured by colorimetry in undegummed and degummed silk fibers sharply increased in the early stage of irradiation. Yellow color indices (b/L) of the specimen subjected to gamma-irradiation continued to increase and the yellow color of the silk threads became more pronounced above a total dose of irradiation of 21 Mrad. The b/L value of the undegummed silk fiber which had deen irradiated was about 2 times that of the degummed silk fiber. (author)

Effect of gamma irradiation on proteins of some agricultural products

International Nuclear Information System (INIS)

Farag, M.F.S.E.

1994-01-01

Soybean and broad bean were exposed to gamma rays at dose levels of 10 ,30 and 50 KGy. Some chemical changes were studied in beans such as chemical composition, total amino acids, protein electrophoresis and trypsin inhibitor. Also irradiated beans were used as a sole source of protein in feeding rats. Some parameters were studied such as, true growth rate, food intake, protein efficiency ratio, true protein digestibility, biological value, serum total protein and serum albumin . The results indicated that irradiation treatments, did n't cause any obvious effects on the chemical composition . Also, no changes were shown in the number of protein bands. A little difference was observed in the bands density. Irradiation doses caused variable results with the majority of the amino acids, but they led to a gradual reduction in the activity of trypsin inhibitor. Moreover, the irradiation treatments caused an increased food intake. The rats growth rates, protein efficiency ratio, true protein digestibility and protein biological values were increased as the irradiation dose increased, but serum total protein and serum albumin were not affected

Histopathological investigation of radiation necrosis. Coagulation necrosis in the irradiated and non-irradiated brain tumors and in the normal brain tissue

Energy Technology Data Exchange (ETDEWEB)

Nakamura, N [Niigata Univ. (Japan). Brain Research Inst.

1977-01-01

Eighty four irradiated tumors (including 59 gliomas) and the surrounding brain tissue were analyzed. In 'normal' brain tissue, typical coagulation necrosis attributable to irradiation was observed in the cerebral white matter, presenting a whitish-yellow color but no remarkable changes in volume. Histologically there was complete desintegration of myelin and axon. Vascular changes included hyalinous thickening, concentric cleavage, fibrinoid degeneration, adventitial fibrosis and edema of small arteries, fibrin thrombi or occlusion of arterioles and capillaries, and telangiectasia of small veins and venules. While other tumors showed hyalinous or fibrous scar tissue and decrease in volume, the gliomas maintained their original volume without residual tumor cells. Massive coagulation necrosis was occasionally found even in full volume, non-irradiated gliomas (controls), although the changes were fewer and not so varied as in typical radiation necrosis. With small dosages, it was difficult to judge whether the necrosis was caused by irradiation or occurred spontaneously. Coagulation necrosis in tumor tissue was found in 25 of 59 cases (42%) of irradiated gliomas, but in only 2 of 49 cases (4%) of the nonirradiated gliomas. In 49 cases no coagulation necrosis of the surrounding tissue was found. Although histopathological judgement is difficult, it is suggested that there is a significant correlation between coagulation necrosis and irradiation. Discussion of the relationship between coagulation necrosis and NSD (nominal standard dose) led to the conclusion that coagulation necrosis will not be caused by irradiation of less than 1400 rets in NSD.

Testicular function following irradiation of the human prepubertal testis

International Nuclear Information System (INIS)

Shalet, S.M.; Beardwell, C.G.; Jacobs, H.S.; Pearson, D.

1978-01-01

Testicular function was studied in ten men, aged between 17 and 36 years, who had received irradiation for a nephroblastoma during childhood. The dose of scattered irradiation to the testes ranged from 268 to 983 rad. Eight subjects had either oligo-or azoosperma (0 to 5.6 million/ml), seven of whom had an elevated serum follicle stimulating hormone (FSH) level. One subject showed evidence of Leydig cell dysfunction with a raised serum luteinizing hormone level (LH) and a low plasma testosterone concentration. A second group of eight prepubertal males, aged between 8 and 14 years, were studied. These had also been irradiated for abdominal malignancies during childhood and received a similar dose of irradiation to the testis as the first group studied. The plasma testosterone levels were within the normal range in all eight. The mean gonadotropin levels were not significantly different from normal. Thus irradiation-induced damage to the germinal epithelium in prepubertal boys raised FSH levels after puberty but not before it. The conclusion is that inhibin has a minor role in the control of the pre-pubertal hypothalmic-pituitary testicular axis and its contribution to gonadal control of gonadotrophin secretion changes with sexual maturation. (author)

Technology Analysis of Global Smart Light Emitting Diode (LED Development Using Patent Data

Directory of Open Access Journals (Sweden)

Sangsung Park

2017-08-01

Full Text Available Technological developments related to smart light emitting diode (LED systems have progressed rapidly in recent years. In this paper, patent documents related to smart LED technology are collected and analyzed to understand the technology development of smart LED systems. Most previous studies of the technology were dependent on the knowledge and experience of domain experts, using techniques such as Delphi surveys or technology road-mapping. These approaches may be subjective and lack robustness, because the results can vary according to the selected expert groups. We therefore propose a new technology analysis methodology based on statistical modeling to obtain objective and relatively stable results. The proposed method consists of visualization based on Bayesian networks and a linear count model to analyze patent documents related to smart LED technology. Combining these results, a global hierarchical technology structure is created that can enhance the sustainability in smart LED system technology. In order to show how this methodology could be applied to real-world problems, we carry out a case study on the technology analysis of smart LED systems.

Effect of tumor therapeutic irradiation on the mechanical properties of teeth tissue

Energy Technology Data Exchange (ETDEWEB)

Fraenzel, W. [Dept. of Physics, Martin Luther Univ. Halle (Germany); Gerlach, R. [Univ. Clinic and Policlinic for Radiation Therapy, Martin Luther Univ. Halle (Germany); Hein, H.J. [Univ. Clinic and Policlinic for Orthopaedics and Physical Medicine, Martin Luther Univ. Halle (Germany); Schaller, H.G. [Dept. of Operative Dentistry and Periodontology, Martin Luther Univ. Halle (Germany)

2006-07-01

Tumor irradiation of the head-neck area is accompanied by the development of a so-called radiation caries in the treated patients. In spite of conservative therapeutic measures, the process results in tooth destruction. The present study investigated the effects of irradiation on the demineralization and remineralization of the dental tissue. For this purpose, retained third molars were prepared and assigned either to a test group, which was exposed to fractional irradiation up to 60 Gy, or to a non-irradiated control group. Irradiated and non-irradiated teeth were then demineralized using acidic hydroxyl-cellulose gel; afterwards the teeth were remineralized using either Bifluorid12 {sup registered} or elmex gelee {sup registered}. The nanoindentation technique was used to measure the mechanical properties, hardness and elasticity, of the teeth in each of the conditions. The values were compared to the non-irradiated control group. Irradiation decreased dramatically the mechanical parameters of enamel and dentine. In non-irradiated teeth, demineralization had nearly the same effects of irradiation on the mechanical properties. In irradiated teeth, the effects of demineralization were negligible in comparison to non-irradiated teeth. Remineralization with Bifluorid12 {sup registered} or elmex gelee {sup registered} led to a partial improvement of the mechanical properties of the teeth. The enamel was more positively affected, by remineralization than the dentine. (orig.)

Effect of gamma irradiation on chemical composition and nutritive value of sorghum grains

International Nuclear Information System (INIS)

Mekkawy, S.H.

1996-01-01

Sorghum grains were gamma irradiated at 0, 10, 50, 100, 150 and 200 KGy doses using cobalt-60 source. Irradiated and unirradiated sorghum samples were analyzed for crude fiber contents, total nitrogen, fat, ash and tannic acid. Neutral-detergent fiber (NDF), acid-detergent fiber (ADF) and acid detergent lignin (ADL) were also determined. In addition, digestibility coefficient received special attention. The irradiated sorghum grains were incorporated into basal diets and fed to rats during the digestion trials. The results indicated that gamma irradiation had no effects on total nitrogen, fat and ash contents of sorghum grains. Irradiation treatments of sorghum did not cause a pronounced effect on tannic acid content even those received the highest irradiation dose (200 kGy). Moreover, the irradiation treatments decreased the NDF content of sorghum especially those subjected to 100 or 200 kGy. On the other hand, the ADF and ADL values did not show a remarkable change due to irradiation treatments. Hemicellulose content was decreased with the increase of irradiation dose levels. Also, it was noticed that feeding rats on basal diets enriched with irradiated sorghum grains had a beneficial effects on digestibility coefficient. This trend was obvious with animals supplemented with sorghum grains subjected to the relatively high irradiation dose levels. 4 tabs

International acceptance of irradiated food. Legal aspects

International Nuclear Information System (INIS)

1979-01-01

The three international organizations competent in the field of irradiation processing for the preservation of food (FAO, WHO, IAEA), convened, at the end of 1977, an Advisory Group to revise and update the recommendations of a similar group which met in early 1972. The Advisory Group considered how national regulations could be harmonized so as to facilitate the international movement of irradiated food. This publication contains the Report of the Advisory Group, which summarizes the considerations of the Group on regulatory control over the irradiation plant and irradiation of foods, and on assurances for comparability of control (international labelling and documentation). Annexes 1 to 6 are included in order to complete the relevant information on the legal aspects of this subject. They include a Draft General Standard for Irradiated Foods, a Draft Code of Practice for the Operation of Radiation Facilities Used for the Treatment of Foods, Recommendations of a Consultation Group on the Legal Aspects of Food Irradiation, a Listing of the Legislation on Food Irradiation Adopted in Member States (1971-1976), and Model Regulations for the Control of and Trade in Irradiated Food

Irradiation-induced mutation experiments with eiploid and tetraploid tomato plants

International Nuclear Information System (INIS)

Boda, J.

1979-01-01

Tomato mutation experiments are described. The tomatoes used in the experiment were the diploid Reziszta and its autotetraploid variety. The experimental plants were exposed to an irradiation of 5000 rsd for 1-2 days, and after transplantation into the gamma field, to chronic irradiation during the whole growing season. The chronic treatment heavily reduced fertility in the generations of tetraploid tomato plants. Recurrent treatment of tetraploid led to further deterioration in fertility. Several berries were formed with few seeds or with no seeds at all. After three irradiations, the chlorophyll mutation frequency increased in the diploid and tetraploid tomato plants. For diploids, treatment applied at the seedling stage gave a lower chlorophyll mutation frequency. With tetraploids the same treatment induced similar chlorophyll mutation frequency. As regards to phenotypic variability of quantitative characteristics in diploid and tetraploid tomatoes, the single and repeated chronic irradiation induced no increase in the variability of properties like flowering time, weight, height etc. (author)

Legal aspects and international implications of food irradiation

International Nuclear Information System (INIS)

Gerard, Alain.

1977-11-01

This paper reports on the status of work on food irradiation at international level, namely the IAEA/FAO/WHO Vienna recommendations, the proposed EEC directive, and the Codex alimentarius draft standards. It then deals with the legal aspects of the subject, in particular the problems concerning definitions, controls and instructions, and finally reviews the regulations for international trade in irradiated foodstuffs. (NEA) [fr

Theory of void swelling, irradiation creep and growth

International Nuclear Information System (INIS)

Wood, M.H.; Bullough, R.; Hayns, M.R.

Recent progress in our understanding of the fundamental mechanisms involved in swelling, creep and growth of materials subjected to irradiation is reviewed. The topics discussed are: the sink types and their strengths in the lossy continuum; swelling and void distribution analysis, including recent work on void nucleation; and, irradiation creep and growth of zirconium and zircaloy are taken as an example

Polarizing neutron by light-irradiated graphene

International Nuclear Information System (INIS)

Peng, Feng

2015-01-01

We study the spin orientation of the neutron scattered by light-irradiated graphene and calculate the average value of spin z-component of the neutron in terms of a generating functional technique. Our calculation results indicate that there is a remarkable neutron polarization effect when a neutron penetrates graphene irradiated by a circularly polarized light. We analyse the dynamical source of generating this effect from the aspect of photon-mediated interaction between the neutron spin and valley pseudospin. By comparing with the polarization induced by a magnetic field, we find that this polarization may be equivalent to the one led by a magnetic field of several hundred Teslas if the photon frequency is in the X-ray frequency range. This provides an approach of polarizing neutrons. (copyright 2015 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Combined effect of x irradiation and cell-mediated immune reaction

International Nuclear Information System (INIS)

Song, C.W.; Guertin, D.P.

1978-01-01

The combined effect of radiation and cell-mediated immune reaction on tumor cells was investigated in vitro. Mastocytoma P815-X2 cells of DBA mice either were irradiated first and subjected to immune lysis by immune splenic lymphocytes of C57Bl mice, or the tumor cells were subjected to immune reaction first and then irradiated. Cell survival was quantitated by colony formation in soft agar medium. It was observed that cellular immune damage to tumor cells did not influence the response of tumor cells to subsequent radiation. Irradiation of tumor cells first, followed by subjection of the cells to cellular immune reaction, slightly enhanced the death of the tumor cells. It appears that this enhanced death might have resulted from a relative increase in the ratio of the number of cytotoxic immune cells to the number of target tumor cells in the incubation mixture as a consequence of the decrease in the number of viable tumor cells by radiation

Detection methods of irradiated foodstuffs

Energy Technology Data Exchange (ETDEWEB)

Ponta, C C; Cutrubinis, M; Georgescu, R [IRASM Center, Horia Hulubei National Institute for Physics and Nuclear Engineering, PO Box MG-6, RO-077125 Magurele-Bucharest (Romania); Mihai, R [Life and Environmental Physics Department, Horia Hulubei National Institute for Physics and Nuclear Engineering, PO Box MG-6, RO-077125 Magurele-Bucharest (Romania); Secu, M [National Institute of Materials Physics, Bucharest (Romania)

2005-07-01

Full text: Food irradiation has, in certain circumstances, an important role to play both in promoting food safety and in reducing food losses. The safety and availability of nutritious food are essential components of primary health care. WHO actively encourages the proper use of food irradiation in the fight against foodborne diseases and food losses. To this end, it collaborates closely with FAO and IAEA. Food irradiation can have a number of beneficial effects, including delay of ripening and prevention of sprouting; control of insects, parasites, helminths, pathogenic and spoilage bacteria, moulds and yeasts; and sterilization, which enables commodities to be stored unrefrigerated for long periods. The 1990s witnessed a significant advancement in food irradiation processing. As a result, progress has been made in commercialization of the technology, culminating in greater international trade in irradiated foods and the implementation of differing regulations relating to its use in many countries. Codex General Standard for Irradiated Foodstuffs and Recommended International Code of Practice for the Operation of Irradiation Facilities Used for the Treatment of Foods regulate food irradiation at international level. At European Union level there are in power Directive 1999/2/EC and Directive1999/3/EC. Every particular country has also its own regulations regarding food irradiation. In Romania, since 2002 the Norms Regarding Foodstuffs and Food Ingredients Treated by Ionizing Radiation are in power. These Norms are in fact the Romanian equivalent law of the European Directives 1999/2/EC and 1999/3/EC. The greater international trade in irradiated foods has led to the demand by consumers that irradiated food should be clearly labeled as such and that methods capable of differentiating between irradiated and nonirradiated products should be available. Thus a practical basis was sought to allow consumers to exercise a free choice as to which food they purchase. If a

Effect of heavy ion irradiation on C 60

Science.gov (United States)

Lotha, S.; Ingale, A.; Avasthi, D. K.; Mittal, V. K.; Mishra, S.; Rustagi, K. C.; Gupta, A.; Kulkarni, V. N.; Khathing, D. T.

1999-06-01

Thin films of C 60 were subjected to swift heavy ion irradiation spanning the region from 2 to 11 keV/nm of electronic excitation. Studies of the irradiated films by Raman spectroscopy indicated polymerization and damage of the film with an ion fluence. The ion track radii are estimated for various ions using the Raman data. Photoluminescence spectroscopy of the irradiated film indicated a decrease in the C 60 phase with a dose, and an increase in the intensity at the 590 nm wavelength, which is attributed to an increase in the oxygen content.

Micropropagation of Pear Rootstock (Pyrus Communis) by using tissue culture technique and gamma irradiation

International Nuclear Information System (INIS)

El-Sharnouby, M.E.; ESSAM, E.R.; Ayoub, S.

2006-01-01

New growing shoots from healthy pear rootstock (Pyrus communis) trees were taken and sterilized 3 times in dipping water. Explants were subjected to antioxidant treatment, different media, different additives and different BAP and NAA concentrations. The obtained results showed that Murashig-Skoog (MS) supplemented with 1 mg/l BA was better than Gamborg medium. Adding antioxidant solution and adenine sulphate to the culture medium was preferred for maximizing explants development. Exposing the explants to gamma irradiation at different doses decreased tissue culture parameters with increasing gamma doses. However, the low dose of gamma rays (1 Krad) significantly increased the number of shoots than other gamma treatments. Adding of BAP at 2 mg/l to the culture medium increased number and length of shoots. However, addition of 1 mg/l NAA to the rooting medium led to increase the root formation

2. National Seminar on Acceptance and Trade of Irradiated Foods. Proceedings

International Nuclear Information System (INIS)

1997-01-01

This proceedings is a compilation of 18 papers presented at the National Seminar on Acceptance and Trade of Irradiated Food, held in Toluca, Mexico, 27-29 October 1997. It generally deals with international and national legal, technological, health and commercial aspects of food irradiation. Public confidence and consumer acceptance of irradiated food stuff is also the subject of the seminar

Early effects of external gamma irradiation on iodide metabolism in rat thyroid

International Nuclear Information System (INIS)

Niatsetskaya, Z.; Nadolnik, L.

2006-01-01

Full text of publication follows: The exposure of the thyroid gland to therapeutic doses of external gamma irradiation is frequently associated with thyroid dysfunction. Although late irradiation effects are well documented, little is still known about the early functional alterations in the thyroid subjected to radiation therapy. The aim of this study was to examine the early effect of single external gamma irradiation on iodide metabolism in the thyroid. The Wistar female rats were irradiated using a 60 Co installation with a constant capacity of 0.64 Gy/min. The doses used were 0.25, 0.5, 1, 2, 5 Gy. The animals were sacrificed after 24 hours following the irradiation. T he thyroid organ culture was cultivated during 24 h and than was irradiated with a single dose of 5 Gy. The thyroid tissue was assayed for thyro-peroxidase activity and concentrations of total, free and protein -binding iodide. It was shown that the 0.25 Gy irradiation depressed thyroid iodide uptake, which was manifested in decreasing total iodide by 25%. The same tendency was observed after the 0.5 Gy irradiation. In the 1, 2, 5 Gy groups, the concentrations of total and free iodide increased by 26 -34% and 50-68%, accordingly. The level of protein-binding iodide in these groups was within the control values. However, protein-binding/total iodide and protein binding/ free iodide ratios decreased by 17 -41%, suggesting inhibition of thyroglobulin iodination. Thyro-peroxidase (T.P.O.) plays a key role in thyroid hormone synthesis by catalyzing both the iodination of thyroglobulin and the coupling some of the iodo-tyrosyl residues. After 24 hours on irradiation, a 31.5-54% dose-dependent inhibition of T.P.O. activity was shown in the 1, 2 and 5 Gy groups. The irradiation of the rat thyroid organ culture with a single dose of 5 Gy also led to significant inhibition of T.P.O. by 56.91% after 2 hours. We compared the enzyme kinetics of thyro-peroxidase from thyroid microsomal fraction control and

Materials irradiation subpanel report to BESAC neutron sources and research panel

International Nuclear Information System (INIS)

Birtcher, R.C.; Goland, A.N.; Lott, R.

1992-01-01

The future success of the nuclear power option in the US (fission and fusion) depends critically on the continued existence of a healthy national materials-irradiation program. Consideration of the requirements for acceptable materials-irradiation systems in a new neutron source has led the subcommittee to identify an advanced steady-state reactor (ANS) as a better choice than a spallation neutron source. However, the subcommittee also hastens to point out that the ANS cannot stand alone as the nation's sole high-flux mixed-spectrum neutron irradiation source in the next century. It must be incorporated in a broader program that includes other currently existing neutron irradiation facilities. Upgrading and continuing support for these facilities must be planned. In particular, serious consideration should be given to converting the HFIR into a dedicated materials test reactor, and long-term support for several university reactors should be established

In vivo adenylate cyclase activity in ultraviolet- and gamma-irradiated Escherichia coli

Energy Technology Data Exchange (ETDEWEB)

Chatterjee, A; Bhattacharya, A K

1988-06-01

The incorporation of (/sup 14/C)adenine into the cyclic AMP fraction by whole cells of Escherichia coli B/r was taken as a measure of the in vivo adenylate cyclase activity. This activity was significantly inhibited by irradiation of the cells either with /sup 60/Co ..gamma..-rays or with UV light from a germicidal lamp, suggesting inhibition of cyclic AMP synthesis. The incubation of cells after irradiation with lower doses (50-100 Gy) of ..gamma..-rays produced a significant increase of in vivo adenylate cyclase activity, whereas there was no significant change after high doses (150 Gy and above). Dark incubation of cells after irradiation with UV light (54 J m/sup -2/) led to recovery of enzyme activity to the level measured in unirradiated cells. Thus it appears that the catabolite repression of L-arabinose isomerase induced by UV light, as well as ..gamma..-irradiation, is due to reduced cyclic AMP synthesis in irradiated cells.

In vivo adenylate cyclase activity in ultraviolet- and gamma-irradiated Escherichia coli

International Nuclear Information System (INIS)

Chatterjee, A.; Bhattacharya, A.K.

1988-01-01

The incorporation of [ 14 C]adenine into the cyclic AMP fraction by whole cells of Escherichia coli B/r was taken as a measure of the in vivo adenylate cyclase activity. This activity was significantly inhibited by irradiation of the cells either with 60 Co γ-rays or with UV light from a germicidal lamp, suggesting inhibition of cyclic AMP synthesis. The incubation of cells after irradiation with lower doses (50-100 Gy) of γ-rays produced a significant increase of in vivo adenylate cyclase activity, whereas there was no significant change after high doses (150 Gy and above). Dark incubation of cells after irradiation with UV light (54 J m -2 ) led to recovery of enzyme activity to the level measured in unirradiated cells. Thus it appears that the catabolite repression of L-arabinose isomerase induced by UV light, as well as γ-irradiation, is due to reduced cyclic AMP synthesis in irradiated cells. (author)

In vivo adenylate cyclase activity in ultraviolet- and gamma-irradiated Escherichia coli.

Science.gov (United States)

Chatterjee, A; Bhattacharya, A K

1988-06-01

The incorporation of [14C]adenine into the cyclic AMP fraction by whole cells of Escherichia coli B/r was taken as a measure of the in vivo adenylate cyclase activity. This activity was significantly inhibited by irradiation of the cells either with 60Co gamma-rays or with UV light from a germicidal lamp, suggesting inhibition of cyclic AMP synthesis. The incubation of cells after irradiation with lower doses (50-100 Gy) of gamma-rays produced a significant increase of in vivo adenylate cyclase activity, whereas there was no significant change after higher doses (150 Gy and above). Dark incubation of cells after irradiation with UV light (54 J m-2) led to recovery of enzyme activity to the level measured in unirradiated cells. Thus it appears that the catabolite repression of L-arabinose isomerase induced by UV light, as well as gamma-irradiation, is due to reduced cyclic AMP synthesis in irradiated cells.

Morphological profiles of neutron and X-irradiated small intestine

International Nuclear Information System (INIS)

Carr, K.E.; O'Shea, O.; Hazzard, R.A.; McCullough, J.S.; Hume, S.P.; Nelson, A.C.

1996-01-01

This paper describes the response of mouse small intestine, at several time points after treatment with neutron or X-irradiation, using doses expected to give similar effects in terms of crypt/microcolony survival. Using resin histology, the effects of radiation on the numbers of duodenal cell types and measurements of tissue areas were assessed. The results for individual parameters and for an estimate of overall damage are given in a data display, which summarises the morphological profile of the organ after both types of radiation. Damage and recovery were seen for many of the parameters studied but there was no standard response pattern applicable for all parameters. In particular, the response of individual crypt cell types could not be predicted from knowledge of the change in crypt numbers. With regard to the holistic response of the gut, neutron irradiation appeared to have caused more damage and produced more early effects than the X-irradiation. More specifically, neutron treatment led to more damage to the neuromuscular components of the wall, while X-irradiation produced early vascular changes. (author)

The improvement of photocatalytic processes: Design of a photoreactor using high-power LEDs

Directory of Open Access Journals (Sweden)

Marzieh Khademalrasool

2016-09-01

Full Text Available This paper is an attempt to survey the benefits of a well-designed photoreactor containing just 6 ultraviolet (UV high power light emitting diodes (HPLEDs; the power and wavelength of each UV HPLED are 1 W and 365 nm, respectively, the latter being an efficient source for photocatalytic studies. Although the experiment with the 365-nm LEDs is reported here, other LEDs were predicted for conducting similar experiments including green photocatalytic ones. We installed diodes with respect to the luminescence intensity distribution curves (LIDCs or intensity patterns. Then, in order to compare the efficiency of the UV-HPLEDs of the HP-LED photoreactor (HPLED-PhR with that of traditional UV lamps which are extensively used in photocatalytic processes, a set of UV HPLEDs was designed and made up. Next, the performance of HPLED-PhR was compared with that of a traditional fluorescent lamp photoreactor (FL-PhR. As a typical photocatalytic experiment, Zinc Oxide (ZnO nanoparticles were synthesized via co-precipitation method and used as photocatalyst for purification of water polluted with the reactive blue dye (RB, under UV irradiation in two photoreactors. The results showed that the rate of photocatalytic reaction under the UV-LEDs was two times greater than the rate under the traditional fluorescent UV lamps, while both electrical power consumption and manufacturing cost of the HPLED-PhR were less than a quarter of them for the FL-PhR.

Review of recent irradiation-creep results

International Nuclear Information System (INIS)

Coghlan, W.A.

1982-05-01

Materials deform faster under stress in the presence of irradiation by a process known as irradiation creep. This phenomenon is important to reactor design and has been the subject of a large number of experimental and theoretical investigations. The purpose of this work is to review the recent experimental results to obtain a summary of these results and to determine those research areas that require additional information. The investigations have been classified into four subgroups based on the different experimental methods used. These four are: (1) irradiation creep using stress relaxation methods, (2) creep measurements using pressurized tubes, (3) irradiation creep from constant applied load, and (4) irradiation creep experiments using accelerated particles. The similarity and the differences of the results from these methods are discussed and a summary of important results and suggested areas for research is presented. In brief, the important results relate to the dependence of creep on swelling, temperature, stress state and alloying additions. In each of these areas new results have been presented and new questions have arisen which require further research to answer. 65 references

Microstructural evolution in neutron irradiated reactor pressure vessel steels

International Nuclear Information System (INIS)

English, C.A.; Phythian, W.J.

1998-01-01

As a result of the popularity of the Agencies report 'Neutron Irradiation Embrittlement of Reactor Pressure Vessel Steels' of 1975, it was decided that another report on this broad subject would be of use. In this report, background and contemporary views on specially identified areas of the subject are considered as self-contained chapters, written by experts. The microstructural evolution in neutron irradiated reactor pressure vessel steels is described. The damage mechanisms are elaborated and techniques for examining the microstructure are suggested. The importance of the initial damage event is analysed, and the microstructural evolution in RPV steels is examined

Long-term lumen depreciation behavior and failure modes of multi-die array LEDs

Science.gov (United States)

Jayawardena, Asiri; Marcus, Daniel; Prugue, Ximena; Narendran, Nadarajah

2013-09-01

One of the main advantages of multi-die array light-emitting diodes (LEDs) is their high flux density. However, a challenge for using such a product in lighting fixture applications is the heat density and the need for thermal management to keep the junction temperatures of all the dies low for long-term reliable performance. Ten multi-die LED array samples for each product from four different manufacturers were subjected to lumen maintenance testing (as described in IES-LM-80-08), and their resulting lumen depreciation and failure modes were studied. The products were tested at the maximum case (or pin) temperature reported by the respective manufacturer by appropriately powering the LEDs. In addition, three samples for each product from two different manufacturers were subjected to rapid thermal cycling, and the resulting lumen depreciation and failure modes were studied. The results showed that the exponential lumen decay model using long-term lumen maintenance data as recommended in IES TM-21 does not fit for all package types. The failure of a string of dies and single die failure in a string were observed in some of the packages.

Technological quality of irradiated Moroccan citrus fruits

International Nuclear Information System (INIS)

Moussaid El Idrissi, M.; R'Kiek, C.; Farahat Laaroussi, S.; Zantar; Mouhib, M.; El Guerrouj, D.; Toukour, L.

2002-01-01

The effect of irradiation at doses of 125, 250, 375, and 500 Gy, commonly used for quarantine treatment, on the quality of Maroc-late orange, the most common export variety of Morocco was investigated. In the first study fruits were irradiated without any previous cold conditioning treatment as practiced by the export trade for quarantine purposes. In the second study fruits obtained from the normal chain after conditioning was irradiated. Storage of irradiated fruits was studied at room temperature and 10 deg. C at 0 deg. C in case of control fruits. The parameters studied included juice yield, total solids, reducing and total sugars, total acids and volatile acids, dry weight and weight loss. The results showed that irradiation did not affect the technological quality of citrus fruits during four weeks storage. The result thus far points to the possibility for the successful application of irradiation as an alternative quarantine treatment to the classical methods, which result in browning of the peel. The browning phenomenon could be controlled by waxing and will be the subject of a future study. (author)

Effect of irradiation on detection of bacteria in dehydrated vegetables with ATP bioluminescence assay

International Nuclear Information System (INIS)

Xiao Huan; Luo Shishi; Wang Zegang; Feng Min; Zhu Jiating; Chen Xiulan; Zhai Jianqing

2011-01-01

ATP bioluminescence intensity of 4 kinds of irradiated dehydrated vegetables was inconsistent with the bacteria number, the reasons were investigated in this paper. Results showed that irradiation had little effect on background luminescence, and there was no effect on luciferase-luminous system. When irradiation killed the bacteria, the ATPase activity also decreased. As a result, the ATP content in bacteria didn't decreased with the killed of bacteria, which contributed to the increase of free ATP in ATP extract and finally led to the disagreement between the bioluminescence intensity and the actual number of bacteria. When the free ATP in the dehydrated vegetable was removed, the bioluminescence intensity of ATP extract was consistent with the actual number of bacteria in irradiated dehydrated vegetable and ATP bioluminescence technology could be used in bacteria detection of irradiated samples. (authors)

Space charge dynamic of irradiated cyanate ester/epoxy at cryogenic temperatures

Science.gov (United States)

Wang, Shaohe; Tu, Youping; Fan, Linzhen; Yi, Chengqian; Wu, Zhixiong; Li, Laifeng

2018-03-01

Glass fibre reinforced polymers (GFRPs) have been widely used as one of the main electrical insulating structures for superconducting magnets. A new type of GFRP insulation material using cyanate ester/epoxy resin as a matrix was developed in this study, and the samples were irradiated by Co-60 for 1 MGy and 5 MGy dose. Space charge distributed within the sample were tested using the pulsed electroacoustic method, and charge concentration was found at the interfaces between glass fibre and epoxy resin. Thermally stimulated current (TSC) and dc conduction current were also tested to evaluate the irradiation effect. It was supposed that charge mobility and density were suppressed at the beginning due to the crosslinking reaction, and for a higher irradiation dose, molecular chain degradation dominated and led to more sever space charge accumulation at interfaces which enhance the internal electric field higher than the external field, and transition field for conduction current was also decreased by irradiation. Space charge dynamic at cryogenic temperature was revealed by conduction current and TSC, and space charge injection was observed for the irradiated samples at 225 K, which was more obvious for the irradiated samples.

Irradiation-assisted stress corrosion cracking of austenitic alloys

International Nuclear Information System (INIS)

Was, G.S.; Atzmon, M.

1991-01-01

An experimental program has been conducted to determine the mechanism of irradiation-assisted stress-corrosion cracking (IASCC) in austenitic stainless steel. High-energy protons have been used to produce grain boundary segregation and microstructural damage in samples of controlled impurity content. The densities of network dislocations and dislocation loops were determined by transmission electron microscopy and found to resemble those for neutron irradiation under LWR conditions. Grain boundary compositions were determined by in situ fracture and Auger spectroscopy, as well as by scanning transmission electron microscopy. Cr depletion and Ni segregation were observed in all irradiated samples, with the degree of segregation depending on the type and amount of impurities present. P, and to a lesser extent P, impurities were observed to segregate to the grain boundaries. Irradiation was found to increase the susceptibility of ultra-high-purity (UHP), and to a much lesser extent of UHP+P and UHP+S, alloys to intergranular SCC in 288 degree C water at 2 ppm O 2 and 0.5 μS/cm. No intergranular fracture was observed in arcon atmosphere, indicating the important role of corrosion in the embrittlement of irradiated samples. The absence of intergranular fracture in 288 degree C argon and room temperature tests also suggest that the embrittlement is not caused by hydrogen introduced by irradiation. Contrary to common belief, the presence of P impurities led to a significant improvement in IASCC over the ultrahigh purity alloy

Effects of irradiation and storage on granulocytes harvested by continuous-flow centrifugation

International Nuclear Information System (INIS)

Patrone, F.; Dallegri, F.; Brema, F.; Sacchetti, C.

1979-01-01

Five normal subjects were subjected to leukapheresis by continuous-flow-centrifugation (CFC) in the Aminco Celltrifuge. Granulocyte functional capacities were evaluated on the venous blood samples drawn before apheresis and on the cellrich plasma collected by CFC, immediately after collection and after short-term storage at 4degC with or without previous irradiation (1500 rad, 50 rad/min). The CFC technique has been shown to provide cells without functional damage. Irradiation did not appear to influence granulocyte function, as evaluated by in vitro studies. The data demonstrate that granulocytes maintain, even after irradiation, functional activities similar to those found immediately after collection for up to 24 hours of storage at 4degC and exhibit only a moderate loss of function after 48 h. Chemotaxis appears to be the most sensitive detector of cellular damage of stored granulocytes, either irradiated or non-irradiated; this technique may be the most useful for assessment of granulocyte function before transfusion. (author)

Dansk LED - Museumsbelysning

DEFF Research Database (Denmark)

Poulsen, Peter Behrensdorff; Dam-Hansen, Carsten; Thorseth, Anders

Projektet har til formål at anvende dansk forskning inden for optik og lys til at realisere innovative energieffektive LED lyssystemer til museumsbranchen.......Projektet har til formål at anvende dansk forskning inden for optik og lys til at realisere innovative energieffektive LED lyssystemer til museumsbranchen....

Detection of irradiated potato and garlic by thermoluminescence measurement

International Nuclear Information System (INIS)

Chung, H.W.; Kwon, J.H.

1998-01-01

Potato and garlic irradiated with gamma ray and electron beam at sprout-inhibition doses, 0.15 and 0.30 kGy were subjected to the detection whether they are irradiated or not by measuring thermoluminescence(TL) for the minerals adhering to the samples. Minerals extracted from the samples showed a high correlation coefficients between absorbed doses and corresponding TL responses. Nonirradiated samples, however, did not exhibit characteristic TL glowcurves. Major glowcurve peaks were observed at 200 to in all irradiated samples. TL intensity was proportional to irradiated doses, but it varied with the samples tested even at the same dose. It can be concluded from the results that detection of irradiated potato and garlic is possible by measuring TL for extracted minerals from the unknown samples

Comparison of UV-LED and low pressure UV for water disinfection: Photoreactivation and dark repair of Escherichia coli.

Science.gov (United States)

Li, Guo-Qiang; Wang, Wen-Long; Huo, Zheng-Yang; Lu, Yun; Hu, Hong-Ying

2017-12-01

Studies on ultraviolet light-emitting diode (UV-LED) water disinfection have shown advantages, such as safety, flexible design, and lower starting voltages. However, information about reactivation after UV-LED disinfection is limited, which is an important issue of UV light-based technology. In this study, the photoreactivation and dark repair of Escherichia coli after UV-LEDs and low pressure (LP) UV disinfection were compared. Four UV-LED units, 265 nm, 280 nm, the combination of 265 + 280 (50%), and 265 + 280 (75%) were tested. 265 nm LEDs was more effective than 280 nm LEDs and LP UV lamps for E. coli inactivation. No synergic effect for disinfection was observed from the combination of 265 and 280 nm LEDs. 265 nm LEDs had no different reactivation performances with that of LP UV, while 280 nm LEDs could significantly repress photoreactivation and dark repair at a low irradiation intensity of 6.9 mJ/cm 2 . Furthermore, the UV-induced damage of 280 nm LEDs was less repaired which was determined by endonuclease sensitive site (ESS) assay. The impaired protein activities by 280 nm LEDs might be one of the reasons that inhibited reactivation. A new reactivation rate constant, K max , was introduced into the logistic model to simulate the reactivation data, which showed positive relationship with the maximum survival ratio and was more reasonable to interpret the results of photoreactivation and dark repair. This study revealed the distinct roles of different UV lights in disinfection and reactivation, which is helpful for the future design of UV-LED equipment. Copyright © 2017 Elsevier Ltd. All rights reserved.

The physics of irradiated nuclear fuel

International Nuclear Information System (INIS)

Robin, M.

1980-01-01

The knowledge of the neutron irradiation effect is essential in dealing with all subjects related to the fuel. Neutron irradiation provokes fission reactions within the fuel and produces new nuclides. The formation chains are described and the importance of each isotope in the fuel cycle is explained with regards to its own characteristics. To solve the system of equations giving the evolution of different nuclides concentrations, the corresponding effective cross-sections and flux received are given by standard codes used for reactor calculations. A good test for calculation methods is the experimental study of irradiated fuel. Many techniques have been developed for this purpose. The last chapter compares fuel evolution in different reactors, in connection with some specific characteristics. (author)

Microbiological possibilities to demonstrate that strawberries have been irradiated

International Nuclear Information System (INIS)

Tamminga, S.K.; Beumer, R.R.; Kampelmacher, E.H.

1975-01-01

Samples of greenhouse and outdoor-grown strawberries were divided into two portions, they were wrapped and one portion was irradiated at 200 krad. The composition of the microflora before and after irradiation was investigated. The flora of the non-irradiated samples was composed mainly of gram-negative rod-shaped bacteria belonging, with only a few exceptions, either to the Enterobacteriaceae-family or to the genus Pseudomonas. Also, moulds and yeasts were frequently encountered in varying quantities. Moulds and yeasts did not appear to make good indicator organisms. Gram-negative rod-shaped bacteria were always found to be absent after irradiation when solid media were used, even when starting from samples with numbers in the order of magnitude 10 5 -10 6 /gm. When outdoor-grown strawberries were used, this always led to a clear difference from the cooresponding untreated samples. Greenhouse strawberries, however, sometimes contain, even if they have not been treated, only a very small number of micro-organisms. Consequently, if gram-negative rod-shaped bacteria are present on strawberries they most probably have not been irradiated. Of course, this does not apply if post-contamination has been possible. If there is no growth of the above mentioned bacteria on any of te media used, considerable possibility exists that irradiation has taken place. (orig./MG) [de

Food science symposium: a national food irradiation forum

International Nuclear Information System (INIS)

Anon.

1989-01-01

A national food irradiation forum was held to further promote the use of irradiation for food applications. This offered opportunity for the Department of National Health to announce new legislation for the labelling of irradiated foodstuffs. Subjects which dominated the proceedings included the implementation of labelling legislation and consumer education; cost implications and commercialisation of radurisation; the increasing trend towards the radurisation of processed foodstuffs as opposed to fresh and the future of food irradiation in South Africa. The safety of the irradiation process was stressed. The forum came to the conclusion that South Africa has this technology which has the government's stamp of approval and it is now up to the food industry, the Consumer Council, etc., to educate consumers into realising that they are buying quality products - and that the Radura symbol is a symbol of quality

Meso-scale modeling of irradiated concrete in test reactor

International Nuclear Information System (INIS)

Giorla, A.; Vaitová, M.; Le Pape, Y.; Štemberk, P.

2015-01-01

Highlights: • A meso-scale finite element model for irradiated concrete is developed. • Neutron radiation-induced volumetric expansion is a predominant degradation mode. • Confrontation with expansion and damage obtained from experiments is successful. • Effects of paste shrinkage, creep and ductility are discussed. - Abstract: A numerical model accounting for the effects of neutron irradiation on concrete at the mesoscale is detailed in this paper. Irradiation experiments in test reactor (Elleuch et al., 1972), i.e., in accelerated conditions, are simulated. Concrete is considered as a two-phase material made of elastic inclusions (aggregate) subjected to thermal and irradiation-induced swelling and embedded in a cementitious matrix subjected to shrinkage and thermal expansion. The role of the hardened cement paste in the post-peak regime (brittle-ductile transition with decreasing loading rate), and creep effects are investigated. Radiation-induced volumetric expansion (RIVE) of the aggregate cause the development and propagation of damage around the aggregate which further develops in bridging cracks across the hardened cement paste between the individual aggregate particles. The development of damage is aggravated when shrinkage occurs simultaneously with RIVE during the irradiation experiment. The post-irradiation expansion derived from the simulation is well correlated with the experimental data and, the obtained damage levels are fully consistent with previous estimations based on a micromechanical interpretation of the experimental post-irradiation elastic properties (Le Pape et al., 2015). The proposed modeling opens new perspectives for the interpretation of test reactor experiments in regards to the actual operation of light water reactors.

Meso-scale modeling of irradiated concrete in test reactor

Energy Technology Data Exchange (ETDEWEB)

Giorla, A. [Oak Ridge National Laboratory, One Bethel Valley Road, Oak Ridge, TN 37831 (United States); Vaitová, M. [Czech Technical University, Thakurova 7, 166 29 Praha 6 (Czech Republic); Le Pape, Y., E-mail: lepapeym@ornl.gov [Oak Ridge National Laboratory, One Bethel Valley Road, Oak Ridge, TN 37831 (United States); Štemberk, P. [Czech Technical University, Thakurova 7, 166 29 Praha 6 (Czech Republic)

2015-12-15

Highlights: • A meso-scale finite element model for irradiated concrete is developed. • Neutron radiation-induced volumetric expansion is a predominant degradation mode. • Confrontation with expansion and damage obtained from experiments is successful. • Effects of paste shrinkage, creep and ductility are discussed. - Abstract: A numerical model accounting for the effects of neutron irradiation on concrete at the mesoscale is detailed in this paper. Irradiation experiments in test reactor (Elleuch et al., 1972), i.e., in accelerated conditions, are simulated. Concrete is considered as a two-phase material made of elastic inclusions (aggregate) subjected to thermal and irradiation-induced swelling and embedded in a cementitious matrix subjected to shrinkage and thermal expansion. The role of the hardened cement paste in the post-peak regime (brittle-ductile transition with decreasing loading rate), and creep effects are investigated. Radiation-induced volumetric expansion (RIVE) of the aggregate cause the development and propagation of damage around the aggregate which further develops in bridging cracks across the hardened cement paste between the individual aggregate particles. The development of damage is aggravated when shrinkage occurs simultaneously with RIVE during the irradiation experiment. The post-irradiation expansion derived from the simulation is well correlated with the experimental data and, the obtained damage levels are fully consistent with previous estimations based on a micromechanical interpretation of the experimental post-irradiation elastic properties (Le Pape et al., 2015). The proposed modeling opens new perspectives for the interpretation of test reactor experiments in regards to the actual operation of light water reactors.

An extraocular non-invasive transscleral LED-endoilluminator for eye speculum integration.

Science.gov (United States)

Kölbl, Philipp Simon; Lindner, Christoph; Lingenfelder, Christian; Deuchler, Svenja; Singh, Pankaj; Koch, Frank; Hessling, Martin

2015-09-01

Conventional chandelier-endoilluminators used for pars-plana vitrectomy consist of a light-emitting tip attached to an optical fibre. The tip requires introduction into the ocular space through an incision. To achieve complete illumination of the intraocular space, the introduction of more than just one tip is sometimes necessary. An extraocular vitreoretinal LED-endoilluminator discussed in this paper represents a new approach to illuminate the intraocular space. The light source is integrated into a speculum and firmly apposed to the sclera. This approach offers the advantage of effectively illuminating the interior of the eye even though the procedure is non-invasive. Furthermore, this approach significantly reduces the risk of damage to the retina by phototoxic effects. A round white LED was used as a light source. By integrating the light source into a speculum, the LED was firmly held against the sclera. Thus, the ocular space was illuminated transsclerally. As a result, indirect uniform illumination of the complete intraocular space was achieved. The prototype was developed considering the relevant international standards. Porcine eyes were used because their properties are similar to those of human eyes. Porcine eyes could be acceptably illuminated with the selected LED. The LED-endoilluminator conforms with international standards for endoillumination. Thus, possible photochemical and thermal risks are considered and reduced to a minimum. A novel LED-endoilluminator which can be attached to a speculum was developed. The system does not need any connection to an external light source and, consequently, also avoids usage of an optical fibre. Regular and uniform illumination of the intraocular space was achieved by transmitted and scattered visible irradiation, avoiding an incision. The duration of potential light exposure, compared to existing illumination systems, can be significantly increased. This is also true when the illuminator is not directly placed

Identification of irradiated chicken meat using electron spin resonance spectroscopy

International Nuclear Information System (INIS)

Chawla, S.P.; Thomas, Paul

2004-01-01

Studies were carried out on detection of irradiation treatment in chicken using electron spin resonance (ESR) spectroscopy. The effect of gamma- irradiation treatment on radiation induced signal in different types of chicken namely, broiler, deshi and layers was studied. Irradiation treatment induced a characteristic ESR signal that was not detected in non-irradiated samples. The shape of the signal was not affected by type of the bone. The intensity of radiation induced ESR signal was affected by factors such as absorbed radiation dose, bone type irradiation temperature, post-irradiation storage, post-irradiation cooking and age of the bird. Deep-frying resulted in the formation of a symmetric signal that had a different shape and was weaker than the radiation induced signal. This technique can be effectively used to detect irradiation treatment in bone-in chicken meat even if stored and/or subjected to various traditional cooking procedures. (author)

Post-irradiation examinations of uranium-plutonium mixed nitride fuel irradiated in JMTR (89F-3A capsule)

International Nuclear Information System (INIS)

Iwai, Takashi; Nakajima, Kunihisa; Kikuchi, Hironobu; Arai, Yasuo; Kimura, Yasuhiko; Nagashima, Hisao; Sekita, Noriaki

2000-03-01

Two helium-bonded fuel pins filled with uranium-plutonium mixed nitride pellets were encapsulated in 89F-3A and irradiated in JMTR up to 5.5% FIMA at a maximum linear power of 73 kW/m. The capsule cooled for ∼5 months was transported to Reactor Fuel Examination Facility and subjected to non-destructive and destructive post irradiation examinations. Any failure was not observed in the irradiated fuel pins. Very low fission gas release rate of about 2 ∼ 3% was observed, while the diametric increase of fuel pin was limited to ∼0.4% at the position of maximum reading. The inner surface of cladding tube did not show any signs of chemical interaction with fuel pellet. (author)

Total lymphoid irradiation in rhesus monkeys

International Nuclear Information System (INIS)

Vriesendorp, H.M.; Maat, B.; Hogeweg, B.

Total lymphoid irradiation (TLI) consists of three contiguous fields, a mantle, an inverted Y and a spleen field. TLI induces a state of immunosuppression in patients with Hodgkin disease or in small rodents. Infusion of allogeneic bone marrow cells into mice after TLI led to the development split haemopoietic chimerism and indefinite survival of skin grafts from the bone marrow donor. A protocol for TLI was developed for rhesus monkeys to attempt to verify these interesting observations in a pre-clinical animal model. (Auth.)

Hepatic metabolic derangement following preoperative irradiation gastric neoplasms

Energy Technology Data Exchange (ETDEWEB)

Berdov, B A; D' yakova, A M; Stefani, N V; Senokosov, N I [Akademiya Meditsinskikh Nauk SSSR, Obninsk. Nauchno-Issledovatel' skij Inst. Meditsinskoj Radiologii

1980-08-01

Preoperative irradiation of gastric cancer results in glycogene buildup in the heratic cells and activation of a number of tissue enzymes such as glutamate-and lactate dehydrogenases, hexogenase, choline esterase and aspartate aminotransferase in the left lobe of the liver which is included in a zone of direct irradiation. The enzyme activation is observed on the 4-7th day after the course of radiotherapy, glycogene maximum content - on the 5th day. The enzyme activity and glycogene content on the 11th day after irradiation decreases to the level of their content in the patients who have not been subjected to radiotherapy.

Radioprotective effect of chitosan in sub-lethally X-ray irradiated mice

Energy Technology Data Exchange (ETDEWEB)

Nishimura, Yoshikazu; Ikota, Nobuo; Arima, Hiromi; Watanabe, Yoshito; Yukawa, Masae; Ozawa, Toshihiko [National Inst. of Radiological Sciences, Chiba (Japan); Kim, Hee-Sun [Korea Hydro and Nuclear Power Corp., Seoul (Korea, Republic of). Radiation Health Research Inst.; Bom, Hee-Seung; Kim, Young-Ho [Chonnam Univ., Kwangju (Korea, Republic of). Hospital

2003-03-01

The radioprotective effect of chitosan was studied in mice following whole-body X-ray irradiation. C3H/He mice were exposed to 7 Gy, and their survival rates were examined. The survival rates of chitosan-diet mice were about 20% higher than those of mice on a standard diet, and the rates dropped sharply to a plateau at day 10 after X-ray irradiation. The chitosan-diet mice had an increased weight ratio of spleen to body within the experimental period. The leukocyte, thrombocyte, and erythrocyte counts as well as the hematocrit and hemoglobin levels were recovered significantly and more rapidly in the chitosan-diet mice than the standard-diet mice at day 14 after irradiation. The scavenging abilities of chitosan were evaluated by the electron spin resonance (ESR) spin-trapping method. These observations suggested that chitosan led to hematopoetic activation and leuko-cytogenesis in mice after sub-lethal dose irradiation, and that the biological response might be caused by radical trapping or scavenging. (author)

Void formation by annealing of neutron-irradiated plastically deformed molybdenum

International Nuclear Information System (INIS)

Petersen, K.; Nielsen, B.; Thrane, N.

1976-01-01

The positron annihilation technique has been used in order to study the influence of plastic deformation on the formation and growth of voids in neutron irradiated molybdenum single crystals treated by isochronal annealing. Samples were prepared in three ways: deformed 12-19% before irradiation, deformed 12-19% after irradiation, and - for reference purposes -non-deformed. In addition a polycrystalline sample was prepared in order to study the influence of the grain boundaries. All samples were irradiated at 60 0 C with a flux of 2.5 x 10 18 fast neutrons/cm 2 . After irradiation the samples were subjected to isochronal annealing. It was found that deformation before irradiation probably enhanced the formation of voids slightly. Deformation after irradiation strongly reduced the void formation. The presence of grain boundaries in the polycrystalline sample had a reducing influence on the growth of voids. (author)

Effects of UV-C irradiation on development of goldfish embryos

International Nuclear Information System (INIS)

Wu Jian; Dai Guifu; Zhang Fengqiu; Lu Lei

2005-01-01

Goldfish embryos at five different developmental stages, from fertilized eggs to heat beating stage, were irradiated by UV rays, and hatching rate, darkly pigmented eye rate and abnormal embryo rate of the irradiated embryos were investigated. Being subjected to very low amount (≤3 min.) of the UV irradiation, the embryos earlier than gastrula stage showed hormesis. However, the embryos at gastrula or heart beating stage were very sensitive to UV irradiation, showing just damage effect, which was very strong even at very low amount of the UV irradiation. The results also showed that development of the gastrula embryos irradiated by the UV rays stopped before darkly pigmented eye state, whereas embryos irradiated at heart beating stage by the UV rays could develop to the darkly pigmented eye stage, though they could not hatch out. (authors)

Color homogeneity in LED spotlights

NARCIS (Netherlands)

Prins, C.R.

2013-01-01

Color variation in the light output of white LEDs is a common problem in LED lighting. We aim to design LED spotlights with a uniform color output while keeping the cost of the system low and the energy efficiency high. Therefore we design a special optic to eliminate the color variation of the LED.

Depletion of new neurons by image guided irradiation

Directory of Open Access Journals (Sweden)

Yao-Fang eTan

2011-04-01

Full Text Available Ionizing radiation continues to be a relevant tool in both imaging and the treatment of cancer. Experimental uses of focal irradiation have recently been expanded to studies of new neurons in the adult brain. Such studies have shown cognitive deficits following radiation treatment and raised caution as to possible unintentional effects that may occur in humans. Conflicting outcomes of the effects of irradiation on adult neurogenesis suggest that the effects are either transient or permanent. In this study, we used an irradiation apparatus employed in the treatment of human tumors to assess radiation effects on rat neurogenesis. For subjects we used adult male rats (Sprague-Dawley under anesthesia. The irradiation beam was directed at the hippocampus, a center for learning and memory and the site of neurogenic activity in adult brain. The irradiation was applied at a dose-rate 0.6 Gy/min for total single-fraction, doses ranging from 0.5-10.0 Gy. The animals were returned to home cages and recovered with no sign of any side effects. The neurogenesis was measured either 1 week or 6 weeks after the irradiation. At 1 week, the number of neuronal progenitors was reduced in a dose-dependent manner with the 50% reduction at 0.78 Gy. The dose-response curve was well fitted by a double exponential suggesting two processes. Examination of the tissue with quantitative immunohistochemistry revealed a dominant low-dose effect on neuronal progenitors resulting in 80% suppression of neurogenesis. This effect was partially reversible, possibly due to compensatory proliferation of the remaining precursors. At higher doses (> 5Gy there was additional, nearly complete block of neurogenesis without compensatory proliferation. We conclude that notwithstanding the usefulness of irradiation for experimental purposes, the exposure of human subjects to doses often used in radiotherapy treatment could be damaging and cause cognitive impairments.

Molecular Effects of Irradiation (Cobalt-60 on the Control of Panonychus citri (Acari: Tetranychidae

Directory of Open Access Journals (Sweden)

Ke Zhang

2015-11-01

Full Text Available The effective dose of irradiation to control pest mites in quarantine has been studied extensively, but the molecular mechanisms underlying the effects of the irradiation on mites are largely unknown. In this study, exposure to 400 Gy of γ rays had significant (p < 0.05 effects on the adult survival, fecundity and egg viability of Panonychus citri. The irradiation caused the degradation of the DNA of P. citri adults and damaged the plasma membrane system of the egg, which led to condensed nucleoli and gathered yolk. Additionally, the transcriptomes and gene expression profiles between irradiated and non-irradiated mites were compared, and three digital gene expression libraries were assembled and analyzed. The differentially expressed genes were putatively involved in apoptosis, cell death and the cell cycle. Finally, the expression profiles of some related genes were studied using quantitative real-time PCR. Our study provides valuable information on the changes in the transcriptome of irradiated P. citri, which will facilitate a better understanding of the molecular mechanisms that cause the sterility induced by irradiation.

Arrays of microLEDs and astrocytes: biological amplifiers to optogenetically modulate neuronal networks reducing light requirement.

Directory of Open Access Journals (Sweden)

Rolando Berlinguer-Palmini

Full Text Available In the modern view of synaptic transmission, astrocytes are no longer confined to the role of merely supportive cells. Although they do not generate action potentials, they nonetheless exhibit electrical activity and can influence surrounding neurons through gliotransmitter release. In this work, we explored whether optogenetic activation of glial cells could act as an amplification mechanism to optical neural stimulation via gliotransmission to the neural network. We studied the modulation of gliotransmission by selective photo-activation of channelrhodopsin-2 (ChR2 and by means of a matrix of individually addressable super-bright microLEDs (μLEDs with an excitation peak at 470 nm. We combined Ca2+ imaging techniques and concurrent patch-clamp electrophysiology to obtain subsequent glia/neural activity. First, we tested the μLEDs efficacy in stimulating ChR2-transfected astrocyte. ChR2-induced astrocytic current did not desensitize overtime, and was linearly increased and prolonged by increasing μLED irradiance in terms of intensity and surface illumination. Subsequently, ChR2 astrocytic stimulation by broad-field LED illumination with the same spectral profile, increased both glial cells and neuronal calcium transient frequency and sEPSCs suggesting that few ChR2-transfected astrocytes were able to excite surrounding not-ChR2-transfected astrocytes and neurons. Finally, by using the μLEDs array to selectively light stimulate ChR2 positive astrocytes we were able to increase the synaptic activity of single neurons surrounding it. In conclusion, ChR2-transfected astrocytes and μLEDs system were shown to be an amplifier of synaptic activity in mixed corticalneuronal and glial cells culture.

Arrays of microLEDs and astrocytes: biological amplifiers to optogenetically modulate neuronal networks reducing light requirement.

Science.gov (United States)

Berlinguer-Palmini, Rolando; Narducci, Roberto; Merhan, Kamyar; Dilaghi, Arianna; Moroni, Flavio; Masi, Alessio; Scartabelli, Tania; Landucci, Elisa; Sili, Maria; Schettini, Antonio; McGovern, Brian; Maskaant, Pleun; Degenaar, Patrick; Mannaioni, Guido

2014-01-01

In the modern view of synaptic transmission, astrocytes are no longer confined to the role of merely supportive cells. Although they do not generate action potentials, they nonetheless exhibit electrical activity and can influence surrounding neurons through gliotransmitter release. In this work, we explored whether optogenetic activation of glial cells could act as an amplification mechanism to optical neural stimulation via gliotransmission to the neural network. We studied the modulation of gliotransmission by selective photo-activation of channelrhodopsin-2 (ChR2) and by means of a matrix of individually addressable super-bright microLEDs (μLEDs) with an excitation peak at 470 nm. We combined Ca2+ imaging techniques and concurrent patch-clamp electrophysiology to obtain subsequent glia/neural activity. First, we tested the μLEDs efficacy in stimulating ChR2-transfected astrocyte. ChR2-induced astrocytic current did not desensitize overtime, and was linearly increased and prolonged by increasing μLED irradiance in terms of intensity and surface illumination. Subsequently, ChR2 astrocytic stimulation by broad-field LED illumination with the same spectral profile, increased both glial cells and neuronal calcium transient frequency and sEPSCs suggesting that few ChR2-transfected astrocytes were able to excite surrounding not-ChR2-transfected astrocytes and neurons. Finally, by using the μLEDs array to selectively light stimulate ChR2 positive astrocytes we were able to increase the synaptic activity of single neurons surrounding it. In conclusion, ChR2-transfected astrocytes and μLEDs system were shown to be an amplifier of synaptic activity in mixed corticalneuronal and glial cells culture.

Bacterial flora of spices and its control by gamma irradiation

International Nuclear Information System (INIS)

El-Zawahry, Y.A.; Youssef, Y.A.; Awny, N.M.; Hussein, H.A.

1985-01-01

The bacterial contamination was tested in 26 samples of spices. Chili, allspice and paprika were the most contaminated spices by bacteria. Five bacterial genera were isolated, namely bacillus, staphylococcus, streptococcus, micrococcus, and coccobacillus, all being gram-positive. Most isolates have been related to the genus bacillus. The bacterial isolates were identified as B. alvei, B. circulans, B. megaterium, B. pasteurii, B. pumilus, B. thuringiensis, B. sphaericus, B. incertaesedis, Micrococcus luteus, staphylococcus aureus, streptococcus sp. and coccobacillus sp. Irradiation of spices led to a significant decrease in the bacterial count of all samples. The dose required to inhibit completely the natural bacterial flora was 25 KGY. The most radioresistant isolates were staphylococcus aureus and micrococcus luteus which were subjected to sublethal doses of 15 and 20 KGY respectively. The dose response curves of the 2 most radioresistant isolates showed simple exponential relationship. The D 10-value of S. aureus and M. luteus were 0.9 and 1.1 KGY, respectively. The effect of storage period on the bacterial load of, as well as, the antibacterial activity of the tested spices were investigated. (author)

Bacterial flora of spices and its control by gamma irradiation

Energy Technology Data Exchange (ETDEWEB)

El-Zawahry, Y A; Youssef, Y A; Awny, N M; Hussein, H A

1985-01-01

The bacterial contamination was tested in 26 samples of spices. Chili, allspice and paprika were the most contaminated spices by bacteria. Five bacterial genera were isolated, namely bacillus, staphylococcus, streptococcus, micrococcus, and coccobacillus, all being gram-positive. Most isolates have been related to the genus bacillus. The bacterial isolates were identified as B. alvei, B. circulans, B. megaterium, B. pasteurii, B. pumilus, B. thuringiensis, B. sphaericus, B. incertaesedis, Micrococcus luteus, staphylococcus aureus, streptococcus sp. and coccobacillus sp. Irradiation of spices led to a significant decrease in the bacterial count of all samples. The dose required to inhibit completely the natural bacterial flora was 25 KGY. The most radioresistant isolates were staphylococcus aureus and micrococcus luteus which were subjected to sublethal doses of 15 and 20 KGY respectively. The dose response curves of the 2 most radioresistant isolates showed simple exponential relationship. The D 10-value of S. aureus and M. luteus were 0.9 and 1.1 KGY, respectively. The effect of storage period on the bacterial load of, as well as, the antibacterial activity of the tested spices were investigated.

Investigating the embryo/larval toxic and genotoxic effects of {gamma} irradiation on zebrafish eggs

Energy Technology Data Exchange (ETDEWEB)

Simon, O., E-mail: olivier.simon@irsn.fr [Laboratoire de Radioecologie et d' Ecotoxicologie, Institut de Radioprotection et de Surete Nucleaire, Cadarache, Bat 186, BP3, 13115 Saint-Paul-lez-Durance Cedex (France); Massarin, S. [Laboratoire de Modelisation Environnementale, Institut de Radioprotection et de Surete Nucleaire, Cadarache, Bat 159, BP3, 13115 Saint-Paul-lez-Durance Cedex (France); Coppin, F. [Laboratoire de Radioecologie et d' Ecotoxicologie, Institut de Radioprotection et de Surete Nucleaire, Cadarache, Bat 186, BP3, 13115 Saint-Paul-lez-Durance Cedex (France); Hinton, T.G. [Service d' Etude du Comportement des Radionucleides dans les Ecosystemes, Institut de Radioprotection et de Surete Nucleaire, Cadarache, Bat 159, BP3, 13115 Saint-Paul-lez-Durance Cedex (France); Gilbin, R. [Laboratoire de Radioecologie et d' Ecotoxicologie, Institut de Radioprotection et de Surete Nucleaire, Cadarache, Bat 186, BP3, 13115 Saint-Paul-lez-Durance Cedex (France)

2011-11-15

Eggs/larval of freshwater fish (Danio rerio) were exposed to low dose rates of external gamma radiation (from 1 to 1000 mGy d{sup -1}) over a 20-day period, with the objective of testing the appropriateness of the 10 mGy d{sup -1} guideline suggested by the IAEA. The present study examines different endpoints, mortality and hatching time and success of embryos as well as the genotoxicity of {gamma}-irradiations (after 48 h). The 20-day embryo-larval bioassay showed an enhanced larval resistance to starvation after chronic exposure to {gamma} irradiation (from low 1 mGy d{sup -1} to high dose rate 1000 mGy d{sup -1}) and an acceleration in hatching time. Gamma irradiation led to increased genotoxic damage Ito zebrafish egg (40-50% DNA in tail in Comet assay) from the lowest dose rate (1 mGy d{sup -1}). Possible mechanisms of {gamma} radiotoxicity and implications for radioprotection are discussed. - Highlights: > Relevant information on the {gamma} radiation impact on early life stage biota is scarce. > The eggs of zebrafish Danio rerio were selected as biological model. > We test the appropriateness of the 10 mGy d{sup -1} guideline (IAEA). > We observed effects measured at individual levels (starvation, hatching time). > Chronic gamma irradiation led to increased genotoxic damage to zebrafish egg. > {gamma} radiotoxicity mechanisms and implications for radioprotection are discussed.

Irradiation studies of mallard duck eggs material containing Mirex

International Nuclear Information System (INIS)

Lane, R.H.; Grodner, R.M.; Graves, J.L.

1976-01-01

Eggs containing Mirex (dodecachloropentacyclo[5.3.0.0 2 , 6 .0 3 , 9 .0 4 , 8 ]decane) from mallard ducks (Anas platyrhychos l.), fed diets with the insecticide incorporated at levels of 1 and 100 ppM for 25 weeks, were subjected to ultraviolet (uv) and γ irradiation. Seven derivatives were obtained on photolysis and eight derivatives were obtained from γ irradiation. Irradiation products appeared to be mono and dihydro derivatives of Mirex. Structural assignments for two monohydro derivatives and three dihydro derivatives were made on the basis of retention time and mass spectral data

Thyroid gland irradiations and thyroid cancers; Critical bibliographic journal; Irradiations de la thyroide et cancers thyroidiens. Revue bibliographique critique

Energy Technology Data Exchange (ETDEWEB)

Vitauxa, F. [CHI Le Raincy-Montfermeil, Faculte X. Bichat, Lab. de Biophysique, Service de Medecine Nucleaire, 93 - Le Raincy-Montfermeil (France)

2007-07-15

The large increase in the incidence of thyroid cancer among children who were mainly less than five years old at the time of the Chernobyl accident is still a major concern for endocrinologists and nuclear medicine physicians. Epidemiological studies have focused solely on iodine-131. However, past knowledge on thyroid irradiation (medical use of iodine-131, radioactive fallout on Marshall islands and the Nevada and Hanford site releases) as well as number of recent works (about low-dose irradiation) raise question on the role of other factors. It is here shown that post-Chernobyl thyroid irradiation is complex and that all factors (iodine-131, but also short lived isotopes of iodine and external irradiation) should be considered. Finally, one needs to think about some of the present medical uses of iodine-131 and especially to the treatment of hyperthyroidism in young subjects. (author)

Geriatric and Student Perceptions following Student-led Educational Sessions

Directory of Open Access Journals (Sweden)

Kristin Janzen

2018-01-01

Full Text Available Objective: The objective of this study was to measure the effect of student-led educational events on geriatric patient and student participant perceptions in a community setting. Methods: Students led three events at a senior community center, focusing on learning and memory, sleep hygiene, and arthritis pain. The participants were geriatric patients who themselves were providers of support to homebound peers (“clients” through an independently organized program. Geriatric participants completed pre- and post-event surveys to measure changes in familiarity with the topics. Student participants also completed pre- and post-event surveys that tracked changes in their comfort in working with the geriatric population. Results: Each event demonstrated at least one positive finding for geriatric patients and/or their clients. Students reported increased comfort in working with and teaching the geriatric population following the first and third events, but not the second. Conclusion: Student-led educational sessions can improve perceived health-related knowledge of geriatric participants while simultaneously exposing students to the geriatric patient population. Overall, both students and geriatric participants benefited from these events. Practice Implications: Incorporation of single, student-led educational events could be mutually beneficial to students and the elderly population in the community and easily incorporated into any healthcare curriculum. Funding:This work was supported by a Butler University Innovation Fund Grant. Treatment of Human Subjects: IRB review/approval required and obtained   Type: Original Research

Monitoring of TiO2-catalytic UV-LED photo-oxidation of cyanide contained in mine wastewater and leachate.

Science.gov (United States)

Kim, Seong Hee; Lee, Sang Woo; Lee, Gye Min; Lee, Byung-Tae; Yun, Seong-Taek; Kim, Soon-Oh

2016-01-01

A photo-oxidation process using UV-LEDs and TiO2 was studied for removal of cyanide contained in mine wastewater and leachates. This study focused on monitoring of a TiO2-catalyzed LED photo-oxidation process, particularly emphasizing the effects of TiO2 form and light source on the efficiency of cyanide removal. The generation of hydroxyl radicals was also examined during the process to evaluate the mechanism of the photo-catalytic process. The apparent removal efficiency of UV-LEDs was lower than that achieved using a UV-lamp, but cyanide removal in response to irradiation as well as consumption of electrical energy was observed to be higher for UV-LEDs than for UV-lamps. The Degussa P25 TiO2 showed the highest performance of the TiO2 photo-catalysts tested. The experimental results indicate that hydroxyl radicals oxidize cyanide to OCN(-), NO2(-), NO3(-), HCO3(-), and CO3(2-), which have lower toxicity than cyanide. In addition, the overall efficacy of the process appeared to be significantly affected by diverse operational parameters, such as the mixing ratio of anatase and rutile, the type of gas injected, and the number of UV-LEDs used. Copyright © 2015 Elsevier Ltd. All rights reserved.

Ion-Neutron Irradiated BOR60 Sample Preparation and Characterization: Nuclear Science User Facility 2017 Milestone Report

Energy Technology Data Exchange (ETDEWEB)

Linton, Kory D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Parish, Chad M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Smith, Quinlan B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-09-01

This document outlines the results obtained by Oak Ridge National Laboratory (ORNL) in collaboration with the University of Michigan-led Consolidated Innovative Nuclear Research project, “Feasibility of combined ion-neutron irradiation for accessing high dose levels.” In this reporting period, neutron irradiated were prepared and shipped to the University of Michigan for subsequent ion irradiation. The specimens were returned to ORNL’s Low Activation Materials Development and Analysis facility, prepared via focused ion beam for examination using scanning/transmission electron microscopy (S/TEM), and then examined using S/TEM to measure the as-irradiated microstructure. This report briefly summarizes the S/TEM results obtained at ORNL’s Low Activation Materials Development and Analysis facility.

Processing of Irradiated Graphite to Meet Acceptance Criteria for Waste Disposal. Results of a Coordinated Research Project

International Nuclear Information System (INIS)

2016-05-01

Graphite is widely used in the nuclear industry and in research facilities and this has led to increasing amounts of irradiated graphite residing in temporary storage facilities pending disposal. This publication arises from a coordinated research project (CRP) on the processing of irradiated graphite to meet acceptance criteria for waste disposal. It presents the findings of the CRP, the general conclusions and recommendations. The topics covered include, graphite management issues, characterization of irradiated graphite, processing and treatment, immobilization and disposal. Included on the attached CD-ROM are formal reports from the participants

Comparative study of the tungsten irradiation conditions in IFMIF and DEMO

Energy Technology Data Exchange (ETDEWEB)

Simakov, S.P.; Pereslavtsev, P.; Fischer, U. [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany). Inst. for Neutron Physics and Reactor Technology; Moeslang, A. [Karlsruhe Institute of Technology, Eggenstein-Leopoldshafen (Germany). Inst. for Material Research I

2010-05-15

The International Fusion Material Irradiation Facility (IFMIF) [1] will provide an accelerator based intense neutron source with a white spectrum extending up to 55 MeV for high fluence irradiations of fusion power reactor (FPR) candidate materials. Material samples located in test modules will be subjected to a radiation load anticipated for a fusion power reactor. The highest neutron flux is expected in the High Flux Test Module, which is considered in the IFMIF design to host around 1000 compactly packed stainless steel samples - the main structure materials of power fusion reactors. Another material subjected to the highest loads in a FPR is a tungsten. It is planned to be used as armour tiles for the divertor or the first wall. It turned out that no specific effort has been undertaken so far to search for a suitable irradiation location in the IFMIF Test Cell which provides a reasonable representation of the irradiation conditions in the divertor of a fusion power reactors. (orig.)

Multihydroxy-Anthraquinone Derivatives as Free Radical and Cationic Photoinitiators of Various Photopolymerizations under Green LED.

Science.gov (United States)

Zhang, Jing; Hill, NicholasS; Lalevée, Jacques; Fouassier, Jean-Pierre; Zhao, Jiacheng; Graff, Bernadette; Schmidt, Timothy W; Kable, Scott H; Stenzel, Martina H; Coote, Michelle L; Xiao, Pu

2018-04-20

Multihydroxy-anthraquinone derivatives [i.e., 1,2,4-trihydroxyanthraquinone (124-THAQ), 1,2,7-trihydroxyanthraquinone (127-THAQ), and 1,2,5,8-tetrahydroxyanthraquinone (1258-THAQ)] can interact with various additives [e.g., iodonium salt, tertiary amine, N-vinylcarbazole, and 2-(4-methoxystyryl)-4,6-bis(trichloromethyl)-1,3,5-triazine] under household green LED irradiation to generate active species (cations and radicals). The relevant photochemical mechanism is investigated using quantum chemistry, fluorescence, cyclic voltammetry, laser flash photolysis, steady state photolysis, and electron spin resonance spin-trapping techniques. Furthermore, the multihydroxy-anthraquinone derivative-based photoinitiating systems are capable of initiating cationic photopolymerization of epoxides or divinyl ethers under green LED, and the relevant photoinitiation ability is consistent with the photochemical reactivity (i.e., 124-THAQ-based photoinitiating system exhibits highest reactivity and photoinitiation ability). More interestingly, multihydroxy-anthraquinone derivative-based photoinitiating systems can initiate free radical crosslinking or controlled (i.e., reversible addition-fragmentation chain transfer) photopolymerization of methacrylates under green LED. It reveals that multihydroxy-anthraquinone derivatives can be used as versatile photoinitiators for various types of photopolymerization reactions. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Irradiating rubber laminate containing sensitive agent in layer

International Nuclear Information System (INIS)

Bohm, G.G.A.

1979-01-01

Rubber compounds may be sensitized to cure or partially cure when subjected to irradiation. If certain layers of a rubber laminate are treated with sensitizing materials and other layers wth densensitizing materials a composite is produced having cured and uncured layers after it has been subjected to irradiation. This technique enables the production of composite laminates in which predetermined layers have predetermined physical characteristics which are desirable in the manufacture of the ultimate end product, for example, automotive tires. Several chemicals have been found to accelerate the cure of rubber compounds by irradiation and several have been found which inhibit the cure. Paradichlorobenzene (PDCB) and certain of the thioetherpolythiols are effective cure promotors. Effective retarders include aromatic oils, sulfur, sulfur cure accelerators and some rubber antioxidants and/or antiozonants of the substituted diphenylamine type. The dosage of irradiation is dependent upon several variables: the type of rubber, the promotor or retarder utilized, the level of the promotor or retarder, the thickness of the layer of material, the thickness of adjacent layers of materials, the sequence of the layers of material, the number of the layers of material and whether the irradiation is applied to one or both sides of the composite strip. The dosage may be controlled by the amount of energy employed so that the electrons do not completely penetrate the entire strip. This results in the irradiaton of part of the strip, but not the entire strip. (LL)

In vitro assessment of cardiac performance after irradiation using an isolated working rat heart preparation

International Nuclear Information System (INIS)

Wondergem, J.; Laarse, A. van der; Ravels, F.J.M. van; Wermeskerken, A.-M. van; Verhoeve, H.R.; Graaf, B.W. de; Leer, J.W.H.

1991-01-01

The effect of irradiation on cardiac function was assessed using an isolated working rat heart preparation. The animals were given single doses of X-rays in the range 15-30 Gy to their hearts. Cardiac output (CO = aortic flow + coronary flow), heart weight and body weight were followed for a period of 10 months after treatment. Irradiation led to a decrease in cardiac function. This reduction was dose-dependent and progressive with time after treatment. The shape of the Frank-Starling curves constructed for irradiated hearts suggests a loss of contractile function of the myocardium. Coronary flow rates measured in 'working' hearts and in 'Langendorff' hearts were not significantly changed by the irradiation treatment. The isolated working rat heart preparation proved to be a simple and suitable animal model for the investigation of irradiation-induced cardiotoxicity. (author)

The generation of hourly diffuse irradiation: A model from the analysis of the fluctuation of global irradiance series

International Nuclear Information System (INIS)

Posadillo, R.; Lopez Luque, R.

2010-01-01

An analysis of models for the estimation of hourly diffuse irradiation based on the interrelations between the hourly diffuse fraction k d and the hourly clearness index k t , has concluded that k t is not a sufficient variable for parametrizing the effect of clouds on diffuse irradiation. A detailed study of the dispersion recorded by this diffuse component for a specific clearness index under partly cloudy sky conditions has led to analyzing how the variability in the instantaneous clearness index influences this dispersion. The data sets correspond to 10 years of hourly and instantaneous value records of global and diffuse radiation collected in Cordoba, Spain. In addition to the inclusion of the sine of solar elevation as a variable into the k d -k t correlations, this model propose the inclusion of others parameters related to the variability in the normalized clearness index within an hour and with the fluctuations presented by the time series of the instantaneous values of that index. Also presented is the implementation of an algorithm permitting both the determination of the hourly diffuse irradiation and the discrimination between the different sky conditions in those situations known by the designation partly cloudy sky.

Alteration of T cell function in healthy persons with a history of thymic x irradiation

International Nuclear Information System (INIS)

Rieger, C.H.L.; Kraft, S.C.; Rothberg, R.M.

1975-01-01

The possible late effects of x irradiation to the infantile thymus were investigated by studying immune functions in 12 healthy persons with a history of thymic x irradiation and healthy control subjects. No differences were found in serum immunoglobulin values, humoral antibody levels, lymphocyte counts, and lymphocyte reactivity to phytohemagglutinin, vaccinia virus, purified protein derivative (PPD), and allogeneic cells. The irradiation group exhibited cellular hyperresponsiveness to streptokinase-streptodornase (SK-SD). In contrast, mean skin and in vitro lymphocyte responses to Candida albicans were depressed in the patients with thymic irradiation. A dissociation of these two Candida responses was found in only 1 of 14 healthy control subjects but in 7 of 12 irradiated individuals. While thymic irradiation did not result in impaired immunologic defenses leading to clinical disease, it caused alterations in T cell responses similar to those reported in patients with chronic mucocutaneous candidiasis

Alteration of T cell function in healthy persons with a history of thymic x irradiation

Energy Technology Data Exchange (ETDEWEB)

Rieger, C.H.L.; Kraft, S.C.; Rothberg, R.M.

1975-10-01

The possible late effects of x irradiation to the infantile thymus were investigated by studying immune functions in 12 healthy persons with a history of thymic x irradiation and healthy control subjects. No differences were found in serum immunoglobulin values, humoral antibody levels, lymphocyte counts, and lymphocyte reactivity to phytohemagglutinin, vaccinia virus, purified protein derivative (PPD), and allogeneic cells. The irradiation group exhibited cellular hyperresponsiveness to streptokinase-streptodornase (SK-SD). In contrast, mean skin and in vitro lymphocyte responses to Candida albicans were depressed in the patients with thymic irradiation. A dissociation of these two Candida responses was found in only 1 of 14 healthy control subjects but in 7 of 12 irradiated individuals. While thymic irradiation did not result in impaired immunologic defenses leading to clinical disease, it caused alterations in T cell responses similar to those reported in patients with chronic mucocutaneous candidiasis.

Finding Urban Identity through Culture-led Urban Regeneration

Directory of Open Access Journals (Sweden)

Kyu Hong Hwang

Full Text Available ABSTRACT: A city experiencing a cycle from growth to decline cannot maintain sustainable development without the type of urban identity that could be consolidated by culture-led urban regeneration. A plan for urban regeneration in a declining urban area should be practiced partially or on the whole according to the characteristics of the community. By transforming a low-value and deteriorated area into a highly valued district, the local community can simultaneously restore its social pride, revive the local economy, and realize an urban identity.Firstly, this paper examines urban decline in order to better understand urban regeneration and the need for multidisciplinary management, and also, by considering the necessity for and universal types of urban regeneration, investigates the characteristics of culture-led urban regeneration as a tool for realizing socio-economic revival and urban identity. In particular, this study suggests the action techniques and benchmarking points for urban regeneration by analyzing cases of culture-led urban regeneration in Korea. Three subjects were considered as case studies in this paper: 1 Hanok village in Jeonju city, which changed from a twilight zone to a tourist attraction; 2 Changdong district in Changwon city, which recovered from an area of declining and dark alleyways that had been the hub for arts and culture in the 1970s to become a new artist village; and 3 Cheongju city, which is being transformed from an idle industrial facility into a cultural space. This thesis suggests the implementation process of culture-led urban regeneration to find an urban identity through analysis of the causes of urban decline, the methods of regeneration, and the results of urban regeneration in the three aforementioned cases. In the conclusion section of this paper, the implementation process for culture-led urban regeneration is summarized as consisting of 5 phases: Phase 1, the diagnosis of decline; Phase 2

Post harvest changes gamma-irradiated banana Prata

International Nuclear Information System (INIS)

Vilas Boas, E.V. de; Chitarra, A.B.; Chitarra, M.I.F.

1996-01-01

The effect of the gamma-irradiation was evaluated at 0.25 and 0.50 kGy, on the development of peel coloration, CO 2 and ethylene evolution, conversion of starch to sugars, pulp-to-peel ratio, pectic solubilization and activities of enzymes of the cell wall, pectin methylesterase (PME), and polygalacturonase (PG), during maturation of 'Prata' bananas. The gamma-irradiation did not affect the normal colour development of the fruits. An increase in the ethylene peak and a decrease in the CO 2 peak was observed. The gamma-irradiation did not affect the degradation of starch, while a delay in soluble sugar accumulation was noted on the 6 and 7 colour grades. The fruits subjected to 0.25 kGy had the highest increase in the pulp-to-peel relation, beginning with colour grade 5, due to a possible stress effect of that dose. An increase of pectin solubilization was observed. Higher PME activities were exhibited by irradiated fruits, although the gamma-irradiation suppressed the PG activity throughout the maturation period. The gamma-irradiation did not extend the post-harvest life of 'Prata' bananas. (author) [pt

Food Irradiation Newsletter. V. 10, no. 2

International Nuclear Information System (INIS)

1986-11-01

This issue reports the summary of the Task Force Meeting on the Use of Irradiation to Ensure Hygienic Quality of Food, convened by the International Consultative Group on Food Irradiation (ICGFI) in Vienna, July 1986. The full report of the final FAO/IAEA Research Co-ordination Meeting on Factors Influencing the Utilization of Food Irradiation, convened in Dubrovnik, Yugoslavia in June 1986, contains the conclusion of the work carried out under the Co-ordinated Research Programme in the past 5 years. A Regional Co-ordinated Research Programme for Latin America has been launched with a workshop convened on this subject in Piracicaba, Brazil, July 1986. Also featured is the summary report of the FAO/IAEA Seminar for Asia and the Pacific on the Practical Application of Food Irradiation convened in Shanghai, People's Republic of China, April 1986. The well-attended seminar reported on the progress and development of practical scale application of food irradiation in the region. A successful market testing of irradiated mangoes in Miami, Florida is also described. The outcome of this test is quite significant in view of the Chernobyl accident a few months before the tests. Tabs

Blue light-irradiated human keloid fibroblasts: an in vitro study

Science.gov (United States)

Magni, Giada; Rossi, Francesca; Tatini, Francesca; Pini, Roberto; Coppi, Elisabetta; Cherchi, Federica; Fusco, Irene; Pugliese, Anna Maria; Pedata, Felicita; Fraccalvieri, Marco; Gasperini, Stefano; Pavone, Francesco S.; Tripodi, Cristina; Alfieri, Domenico; Targetti, Lorenzo

2018-02-01

Blue LED light irradiation is currently under investigation because of its effect in wound healing improvement. In this context, several mechanisms of action are likely to occur at the same time, consistently with the presence of different light absorbers within the skin. In our previous studies we observed the wound healing in superficial abrasions in an in vivo murine model. The results evidenced that both inflammatory infiltrate and myofibroblasts activity increase after irradiation. In this study we focused on evaluating the consequences of light absorption in fibroblasts from human cells culture: they play a key role in wound healing, both in physiological conditions and in pathological ones, such as keloid scarring. In particular we used keloids fibroblasts as a new target in order to investigate a possible metabolic or cellular mechanism correlation. Human keloid tissues were excised during standard surgery and immediately underwent primary cell culture extraction. Fibroblasts were allowed to grow in the appropriate conditions and then exposed to blue light. A metabolic colorimetric test (WST-8) was then performed. The tests evidenced an effect in mitochondrial activity, which could be modulated by the duration of the treatment. Electrophysiology pointed out a different behavior of irradiated fibroblasts. In conclusion, the Blue LED light affects the metabolic activity of fibroblasts and thus the cellular proliferation rate. No specific effect was found on keloid fibroblasts, thus indicating a very basic intracellular component, such as cytochromes, being the target of the treatment.

Evidence for DNA repair after ultraviolet irradiation of Petunia hybrida pollen

International Nuclear Information System (INIS)

Jackson, J.F.; Linskens, H.F.; Katholieke Universiteit Nijmegen; Katholike Universiteit Nijmegen

1978-01-01

Ultraviolet irradiation of Petunia hybrida pollen led to an unscheduled labelling of pollen DNA by 3 H-thymidine during the early stages of germination. Hydroxyurea increased this DNA labelling, while added boron, required absolutely for pollen germination, tube elongation and tube generative cell mitosis, was not needed for this repair-like DNA synthesis. (orig.) [de

Detection of irradiation treatment of foods using DNA 'comet assay'

Energy Technology Data Exchange (ETDEWEB)

Khan, Hasan M.; Delincee, Henry

1998-06-01

Microgel electrophoresis of single cells (DNA comet assay) has been investigated to detect irradiation treatment of some food samples. These samples of fresh and frozen rainbow trout, red lentil, gram and sliced almonds were irradiated to 1 or 2 kGy using 10 MeV electron beam from a linear accelerator. Rainbow trout samples yielded good results with samples irradiated to 1 or 2 kGy showing fragmentation of DNA and, therefore, longer comets with no intact cells. Unirradiated samples showed shorter comets with a significant number of intact cells. For rainbow trout stored in a freezer for 11 days the irradiated samples can still be discerned by electrophoresis from unirradiated samples, however, the unirradiated trouts also showed some longer comets besides some intact cells. Radiation treatment of red lentils can also be detected by this method, i.e. no intact cells in 1 or 2 kGy irradiated samples and shorter comets and some intact cells in unirradiated samples. However, the results for gram and sliced almond samples were not satisfactory since some intact DNA cells were observed in irradiated samples as well. Probably, incomplete lysis has led to these deviating results.

Nonthermal effect of microwave irradiation on nitrite uptake in Chlamydomonas reinhardtii

International Nuclear Information System (INIS)

Pedrajas, C.; Cotrino, J.

1989-01-01

When cells of the unicellular green alga Chlamydomonas reinhardtii were subjected to microwave irradiation at 2.45 GHz, nitrite uptake kinetics still obeyed the Michaelis-Menten equation, the Km of the process remaining constant, whereas V max increased, which indicates an enhanced nonthermal permeability in irradiated cells. (author)

Efficiency of Methanolic Extract of Gamma Irradiated Parsley as Antioxidant and Antimicrobial

International Nuclear Information System (INIS)

Abdeldaiem, M.H.; Ali, H.G.M.; Mohamed, E.A.

2011-01-01

Antioxidant and antimicrobial activities of methanolic extract of gamma irradiated parsley (Petroselinum crispum) at dose levels of 3, 6 and 9 kGy were determined, and the composition of methanolic extracts of non-irradiated and irradiated parsley were identified by GC-MS. The results showed that the methanolic extracts of non-irradiated and irradiated parsley had higher contents of total phenolic compounds and exhibited antioxidant of DPPH radical scavenging activity. Based on these results, the methanolic extracts of irradiated parsley at 6 kGy were selected for their higher activity as antioxidant as compared to other samples owing to their high content of total phenolic compounds and scavenging effect on DPPH radical. The analysis by GC-MS led to the identification of 23 and 24 components for non-irradiated and irradiated samples at 6 kGy, respectively. The main compound of the methanolic extract of non-irradiated parsley was acetic acid ethyl ester (28.5%). Meanwhile, the main compound of irradiated parsley at 6 kGy methanolic extract was phenol,2-methoxy-3(27.3 %). The antibacterial effect of methanolic extract of non-irradiated and irradiated parsley and the minimum inhibitory concentration (MIC) values were assayed. The methanolic extract of irradiated parsley (6 kGy) was generally more effective against tested bacterial strains than the extract of non-irradiated parsley. The study exhibited that gram- negative bacteria under study were more sensitive than gram-positive one. The MIC values of tested bacteria of the methanolic extract of irradiated parsley (6 kGy) were in the range 4 to 20 μg/ml. It could be concluded that the methanolic extract of parsley can be used in food industry as natural food additive and in particular that extract from irradiated parsley at 6 kGy

A study of the behaviour of irradiated or unirradiated grafts in the camera aquosa of irradiated and unirradiated animals; Etude du comportement d'un greffon irradie ou non, transplante dans la chambre anterieure de l'oeil d'un animal irradie ou non

Energy Technology Data Exchange (ETDEWEB)

Djalali-Behzad, G [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1969-06-01

Following grafts of new born mice spinal ganglia in the 'camera aquosa' of adult mice, the authors tried hematopoietic tissue grafts in the same conditions. The growth of iso-logous and hetero-logous bone marrow in the 'camera aquosa' showed that this tissue, even after exposure to supralethal doses, was capable of survival and growth. A counter-experiment with non irradiated bone marrow grafts in the 'camera aquosa' of rats delivered 700 rads led to the conclusion that the environment, intoxicated by exposure, acted on the graft so that after vascularization it became unable to grow. (author) [French] Apres avoir greffe des ganglions rachidiens de souriceaux nouveaux-nes dans la chambre anterieure de l'oeil de souris adultes, l'auteur a tente de greffer du tissu hematopoietique de la meme facon. La proliferation de la moelle osseuse isologue et heterologue, dans la chambre anterieure de l'oeil, lui a permis de mettre en evidence une certaine capacite de survie et de proliferation de ce tissu irradie meme a dose supraletale. Par une contre-experimentation, c'est-a-dire par la greffe de moelle non irradiee dans la chambre anterieure de rats irradies a 700 rads, il conclut que le milieu ambiant, intoxique par l'irradiation, agit sur le greffon de telle sorte que ce dernier, apres s'etre vascularise, devient depourvu de son aptitude de proliferation. (auteur)

Consumer Acceptability Of Irradiated Foods

International Nuclear Information System (INIS)

Awoyinka, A.; Akingbohungbe, A.E.

1994-01-01

Three commonly used food items; maize, beans and smoked fish were irradiated and consumer acceptability was tested through a questionnaire method. Subjects were residents in Ile-Ife, Nigeria. Respondents attitudes towards the processing and tasting of the food were very positive and the possibility of marketing the foods was suggested by them

LED Technology for Dental Applications

DEFF Research Database (Denmark)

Argyraki, Aikaterini; Ou, Yiyu; Soerensen, L. H.

LEDs have a large potential in many dental and oral applications. Areas such as photo polymerization, fluorescence imaging, photodynamic therapy, and photoactivated disinfection are important future candidates for LED based diagnostics and treatment in dentistry.......LEDs have a large potential in many dental and oral applications. Areas such as photo polymerization, fluorescence imaging, photodynamic therapy, and photoactivated disinfection are important future candidates for LED based diagnostics and treatment in dentistry....

Effect of LED phototherapy (λ630 +/- 20nm) on mast cells during wound healing in hypothyroid

Science.gov (United States)

Paraguassú, Gardênia M.; De Castro, Isabele Cardoso V.; Vasconcelos, Rebeca M.; da Guarda, Milena G.; Rodriguez, Tânia T.; Ramalho, Maria José P.; Pinheiro, Antônio Luiz B.; Ramalho, Luciana Maria P.

2014-02-01

Hypothyroidism has been associated with the disruption of the body's metabolism, including the healing process. LED phototherapy has been studied using several healing models, but their effects on mast cells proliferation associated to hypothyroidism remains unknown. The aim of this study was to assess the effect LED (λ630+/-20nm) phototherapy on mast cells proliferation during tissue repair in hypothyroid rats. Under general anesthesia, a standard surgical wound (1cm2) was created on the dorsum of 24 male Wistar rats divided into 4 groups of 6 animals each: EC-Control Euthyroid; ED-Euthyroid+LED; HC-Control Hypothyroid and HD-Hypothyroid+LED. The irradiation started immediately after surgery and was repeated every other day for 7 days, when animals death occurred. Hypothyroidism was induced in rats with propylthiouracil (0.05g/100mL) administered orally for 4 weeks and maintained until the end of the experiment. The specimens removed were processed to wax and stained with toluidine blue for mast cell identification. The mast cell proliferation was significantly higher in HC group than in EC group (Mann Whitney, p<0.05), but when ED group was compared to HD group, no significant difference was found. Our results showed that there was increase of mast cells in the presence of hypothyroidism, prolonging the inflammatory phase of repair, and the LED light has a biomodulative effect on mast cell population, even when hipothyroidism was present.

Broadband Radiometric LED Measurements

OpenAIRE

Eppeldauer, G. P.; Cooksey, C. C.; Yoon, H. W.; Hanssen, L. M.; Podobedov, V. B.; Vest, R. E.; Arp, U.; Miller, C. C.

2016-01-01

At present, broadband radiometric measurements of LEDs with uniform and low-uncertainty results are not available. Currently, either complicated and expensive spectral radiometric measurements or broadband photometric LED measurements are used. The broadband photometric measurements are based on the CIE standardized V(��) function, which cannot be used in the UV range and leads to large errors when blue or red LEDs are measured in its wings, where the realization is always poor. Reference irr...

Detection of irradiated deboned turkey meat using electron spin resonance spectroscopy

International Nuclear Information System (INIS)

Gray, Richard; Stevenson, M.H.

1989-01-01

Bone fragments were extracted from two blocks of frozen deboned turkey meat (irradiated and non-irradiated) using alcoholic KOH digestion. Electron spin resonance (ESR) spectroscopy was used to differentiate between the samples. Comparison of an alcoholic KOH digestion procedure with a freeze drying and grinding method showed that the former method gave a signal which was 78% of that obtained using the freeze drying procedure. Regression analysis of the results obtained after subjection of the original non-irradiated sample to irradiation doses of 3.0, 5.0 and 7.0 kGy gave a linear relationship between irradiation dose and ESR signal strength over this range. Using this relationship the estimated mean dose received by the irradiated block was 4.72 kGy. (author)

Photocatalytic Oxidation of Low-Level Airborne 2-Propanol and Trichloroethylene over Titania Irradiated with Bulb-Type Light-Emitting Diodes.

Science.gov (United States)

Jo, Wan-Kuen

2013-01-18

This study examined the photocatalytic oxidation of gas-phase trichloroethylene (TCE) and 2-propanol, at indoor levels, over titanium dioxide (TiO₂) irradiated with light-emitting diodes (LED) under different operational conditions. TiO₂ powder baked at 450 °C exhibited the highest photocatalytic decomposition efficiency (PDE) for TCE, while all photocatalysts baked at different temperatures showed similar PDEs for 2-propanol. The average PDEs of TCE over a three hour period were four, four, five, and 51% for TiO₂ powders baked at 150, 250, 350, and 450 °C, respectively. The average PDEs of 2-propanol were 95, 97, 98, and 96% for TiO₂ powders baked at 150, 250, 350, and 450 °C, respectively. The ratio of anatase at 2θ = 25.2° to rutile at 2θ = 27.4° was lowest for the TiO₂ powder baked at 450 °C. Although the LED-irradiated TiO₂ system revealed lower PDEs of TCE and 2-propanol when compared to those of the eight watt, black-light lamp-irradiated TiO₂ system, the results for the PDEs normalized to the energy consumption were reversed. Other operational parameters, such as relative humidity, input concentrations, flow rate, and feeding type were also found to influence the photocatalytic performance of the UV LED-irradiated TiO₂ system when applied to the cleaning of TCE and 2-propanol at indoor air levels.

Photocatalytic Oxidation of Low-Level Airborne 2-Propanol and Trichloroethylene over Titania Irradiated with Bulb-Type Light-Emitting Diodes

Directory of Open Access Journals (Sweden)

Wan-Kuen Jo

2013-01-01

Full Text Available This study examined the photocatalytic oxidation of gas-phase trichloroethylene (TCE and 2-propanol, at indoor levels, over titanium dioxide (TiO2 irradiated with light-emitting diodes (LED under different operational conditions. TiO2 powder baked at 450 °C exhibited the highest photocatalytic decomposition efficiency (PDE for TCE, while all photocatalysts baked at different temperatures showed similar PDEs for 2-propanol. The average PDEs of TCE over a three hour period were four, four, five, and 51% for TiO2 powders baked at 150, 250, 350, and 450 °C, respectively. The average PDEs of 2-propanol were 95, 97, 98, and 96% for TiO2 powders baked at 150, 250, 350, and 450 °C, respectively. The ratio of anatase at 2θ = 25.2° to rutile at 2θ = 27.4° was lowest for the TiO2 powder baked at 450 °C. Although the LED-irradiated TiO2 system revealed lower PDEs of TCE and 2-propanol when compared to those of the eight watt, black-light lamp-irradiated TiO2 system, the results for the PDEs normalized to the energy consumption were reversed. Other operational parameters, such as relative humidity, input concentrations, flow rate, and feeding type were also found to influence the photocatalytic performance of the UV LED-irradiated TiO2 system when applied to the cleaning of TCE and 2-propanol at indoor air levels.

Effect of insulin on aldolase turnover in irradiated rat liver

International Nuclear Information System (INIS)

Komov, V.P.; Kirillova, N.V.; Bekdzhanyan, A.G.

1984-01-01

A study was made of the effect of insulin on the rate of biosynthesis, ''half life'', spontaneous decomposition and transport of aldolase in mitochondria of liver and blood plasma of rats, subjected to whole-body X-irradiation. The hormone injected after irradiation was shown to normalize the rate of spontaneous decay and the time of aldolase functioning

Post-irradiation annealing of coarse-grained model alloys

Energy Technology Data Exchange (ETDEWEB)

Ray, P H.N.; Wilson, C; McElroy, R J [AEA Reactor Services, Harwell (United Kingdom)

1994-12-31

Thermal ageing and irradiation studies have been carried out on three model alloys (JPC, JPB, JPG) that have identical compositions except for different levels of phosphorus and/or copper. They have been irradiated in three conditions, as-received, heat treated to produce a coarse grained microstructure (similar to heat-affected-zone), and in this condition further aged at 450 C to produce a temper embrittled condition. One of the alloy have been subject to a post-irradiation anneal. The effect of these treatments on mechanical property changes has been characterized by Charpy testing and Vickers hardness measurements; the phosphorus segregation has been studied by a combination of STEM and Auger techniques.

Reproductive function in mice exposed to ancestral and direct irradiation

International Nuclear Information System (INIS)

Nash, D.J.; Sprackling, L.S.

1978-01-01

Reproduction was studied in 13 inbred strains of mice that had been exposed continuously to 60 Co gamma radiation for varying numbers of generations. At weaning the mice were removed from the irradiation chamber and were tested for reproductive performance. Ancestral and direct levels of irradiation were determined for each animal. Each irradiated or control female was scored as fertile or sterile, and in utero litter counts were made in pregnant females that were dissected past the 10th day of pregnancy. The number of resorptions, dead embryos, and live embryos were counted, and the ratio of living embryos to the total number of embryos was determined for each litter. The overall fertility curves were sigmoid in the range of doses below those which caused complete sterility, which indicated some sort of cumulative damage. In 11 of the 13 strains studied, an increase in ancestral and/or direct irradiation led to significant decreases in fertility. The means of the number alive in the litters for the control and irradiated mice in each strain showed a definite trend toward fewer live mice in utero after irradiation. Least-squares analyses of variance were made to detect possible effects of any of six irradiation variables (ancestral linear, ancestral quadratic, ancestral cubic, direct linear, direct quadratic, or direct cubic) or of strain differences on total litter size and on ratio. Strain effects were significant in each instance. Litter size was more likely to be affected by radiation variables than ratios were

Investigation of research and development subjects for the Very High Burnup Fuel

International Nuclear Information System (INIS)

Hayashi, Kimio; Amano, Hidetoshi; Suzuki, Yasufumi; Furuta, Teruo; Nagase, Fumihisa; Suzuki, Masahide

1993-06-01

A concept of the Very High Burnup Fuel aiming at a maximum fuel assembly burnup of 100 GWd/t has been proposed in terms of burnup extension, utilization of Pu and transmutation of transuranium elements (TRU: Np, Am and Cm). The authors have investigated research and development (R and D) subjects of the fuel pellet and the cladding material of the Fuel. The present report describes the results on the fuel pellet. First, the chemical state of the Fuel and fission products (FP) was inferred through an FP-inventory and an equilibrium-thermodynamics calculations. Besides, knowledge obtained from post-irradiation examinations was surveyed. Next, an investigation was made on irradiation behavior of U/Pu mixed oxide (MOX) fuel with high enrichment of Pu, as well as on fission-gas release and swelling behavior of high burnup fuels. Reprocessibility of the Fuel, particularly solubility of the spent fuel, was also examined. As for the TRU-added fuel, material property data on TRU oxides were surveyed and summarized as a database. And the subjects on the production and the irradiation behavior were examined on the basis of experiences of MOX fuel production and TRU-added fuel irradiation. As a whole, the present study revealed the necessity of accumulating fundamental data and knowledge required for design and assessment of the fuel pellet, including the information on properties and irradiation performance of the TRU-added fuel. Finally, the R and D subjects were summarized, and a proposal was made on the way of development of the fuel pellet and cladding materials. (author)

Gamma irradiation-induced modifications of resins found in nuclear waste embedding processes; Modifications induites par irradiation gamma dans les differentes resines rencontrees dans le traitement des dechets nucleaires

Energy Technology Data Exchange (ETDEWEB)

Allali, H [Faculte des Science et Techniques, Settat (Morocco); Debre, O; Lambert, M; Nsouli, B; Thomas, J P [Inst. de Physique Nucleaire, Lyon-1 Univ., 69 - Villeurbanne (France); Collaboration: IPN-Lyon, Laboratoire d` Etude des Materiaux Plastiques et des Biomateriaux, URA 507, UCBL, Agence Nationale pour la Gestion des Dechets Radiactifs

1999-12-31

The various resins involved in nuclear waste disposal are subject to gamma irradiation-induced modifications. From Time-of-Flight Mass Spectrometry of Secondary ions emitted under High Energy Projectiles bombardment (HSF-SIMS) of such materials the following results are obtained: the embedding epoxy resin DGEBA-DDM does not exhibit significant bulk changes in chemical structure, whatever the dose rate and irradiation medium (air or water), at least up to 2 MGy. However, oxidation processes are well observed at the very surface. Under the same conditions Ion exchange resins to be embedded are subjected to scissions of their functional sites, leading to fixed ion release. Dehydration under irradiation is observed pointing out the crucial role of water in ion transport outside of the material. (authors)

Lifetime testing UV LEDs for use in the LISA charge management system

Science.gov (United States)

Hollington, D.; Baird, J. T.; Sumner, T. J.; Wass, P. J.

2017-10-01

As a future charge management light source, UV light-emitting diodes (UV LEDs) offer far superior performance in a range of metrics compared to the mercury lamps used in the past. As part of a qualification program a number of short wavelength UV LEDs have been subjected to a series of lifetime tests for potential use on the laser interferometer space antenna (LISA) mission. These tests were performed at realistic output levels for both fast and continuous discharging in either a DC or pulsed mode of operation and included a DC fast discharge test spanning 50 days, a temperature dependent pulsed fast discharge test spanning 21 days and a pulsed continuous discharge test spanning 507 days. Two types of UV LED have demonstrated lifetimes equivalent to over 25 years of realistic mission usage with one type providing a baseline for LISA and the other offering a backup solution.

Lifetime testing UV LEDs for use in the LISA charge management system

International Nuclear Information System (INIS)

Hollington, D; Baird, J T; Sumner, T J; Wass, P J

2017-01-01

As a future charge management light source, UV light-emitting diodes (UV LEDs) offer far superior performance in a range of metrics compared to the mercury lamps used in the past. As part of a qualification program a number of short wavelength UV LEDs have been subjected to a series of lifetime tests for potential use on the laser interferometer space antenna (LISA) mission. These tests were performed at realistic output levels for both fast and continuous discharging in either a DC or pulsed mode of operation and included a DC fast discharge test spanning 50 days, a temperature dependent pulsed fast discharge test spanning 21 days and a pulsed continuous discharge test spanning 507 days. Two types of UV LED have demonstrated lifetimes equivalent to over 25 years of realistic mission usage with one type providing a baseline for LISA and the other offering a backup solution. (paper)

Clinical and symptomatological study of pigs subjected to a lethal dose of integral gamma irradiation; Etude clinique et symptomatologique chez le porc soumis a une irradiation gamma totale a dose letale

Energy Technology Data Exchange (ETDEWEB)

Vaiman, M; Guenet, J -L; Maas, J; Nizza, P

1966-05-01

Results are reported from a clinical and haematological study on a Corsican species of pigs wholly exposed to an approximately lethal dose of {gamma} radiation. The aim of this work was to examine the changes in the irradiation syndrome of irradiation for pigs to make it thus possible to devise further experiments, in particular in the therapeutic field. The dose received was 285 rads (measured as the absorption in the vertical antero-posterior medial plane). Data are presented on cyto-haematological changes in the blood circulating immediately after irradiation, and followed up to death, and changes in the medullary cytology after irradiation. The clinical picture of lethal radiation injury in swine is described. (authors) [French] Les auteurs rapportent les resultats d'une etude clinique et hematologique chez des porcs de race corse irradies in toto a dose sensiblement letale. Le but de cette etude etait de connaitre l'evolution du syndrome aigu d'irradiation chez le porc et de permettre ainsi le developpement d'experimentations ulterieures, en particulier dans le domaine therapeutique. La dose delivree etait de 285 rad (en dose absorbee au niveau du plan median vertical anteroposterieur. L'etude a porte essentiellement: 1. Sur les modifications cyclo-hematologiques du sang circulant immediatement apres l'irradiation, pour les differentes lignees cellulaires; l'evolution de ces modifications a ete notee jusqu'a la mort; 2. Sur les modifications de la cytologie medullaire apres irradiation (evolution du myelogramme et essai d'evaluation de la cellularite de la moelle osseuse);: 3. Sur les signes cliniques, d'ailleurs tres discrets, observes chez les porcs apres irradiation. (auteurs)

Clinical and symptomatological study of pigs subjected to a lethal dose of integral gamma irradiation; Etude clinique et symptomatologique chez le porc soumis a une irradiation gamma totale a dose letale

Energy Technology Data Exchange (ETDEWEB)

Vaiman, M.; Guenet, J.-L.; Maas, J.; Nizza, P

1966-05-01

Results are reported from a clinical and haematological study on a Corsican species of pigs wholly exposed to an approximately lethal dose of {gamma} radiation. The aim of this work was to examine the changes in the irradiation syndrome of irradiation for pigs to make it thus possible to devise further experiments, in particular in the therapeutic field. The dose received was 285 rads (measured as the absorption in the vertical antero-posterior medial plane). Data are presented on cyto-haematological changes in the blood circulating immediately after irradiation, and followed up to death, and changes in the medullary cytology after irradiation. The clinical picture of lethal radiation injury in swine is described. (authors) [French] Les auteurs rapportent les resultats d'une etude clinique et hematologique chez des porcs de race corse irradies in toto a dose sensiblement letale. Le but de cette etude etait de connaitre l'evolution du syndrome aigu d'irradiation chez le porc et de permettre ainsi le developpement d'experimentations ulterieures, en particulier dans le domaine therapeutique. La dose delivree etait de 285 rad (en dose absorbee au niveau du plan median vertical anteroposterieur. L'etude a porte essentiellement: 1. Sur les modifications cyclo-hematologiques du sang circulant immediatement apres l'irradiation, pour les differentes lignees cellulaires; l'evolution de ces modifications a ete notee jusqu'a la mort; 2. Sur les modifications de la cytologie medullaire apres irradiation (evolution du myelogramme et essai d'evaluation de la cellularite de la moelle osseuse);: 3. Sur les signes cliniques, d'ailleurs tres discrets, observes chez les porcs apres irradiation. (auteurs)

LED lamp color control system and method

Science.gov (United States)

Gaines, James; Clauberg, Bernd; Van Erp, Josephus A.M.

2013-02-05

An LED lamp color control system and method including an LED lamp having an LED controller 58; and a plurality of LED channels 60 operably connected to the LED controller 58, each of the plurality of LED channels 60 having a channel switch 62 in series with at least one shunted LED circuit 83, the shunted LED circuit 83 having a shunt switch 68 in parallel with an LED source 80. The LED controller 58 determines whether the LED source 80 is in a feedback controllable range, stores measured optical flux for the LED source 80 when the LED source 80 is in the feedback controllable range, and bypasses storing the measured optical flux when the LED source 80 is not in the feedback controllable range.

Functional hyposplenia after splenic irradiation for Hodgkin's disease

International Nuclear Information System (INIS)

Coleman, C.N.; McDougall, I.R.; Dailey, M.O.; Ager, P.; Bush, S.; Kaplan, H.S.

1982-01-01

We previously reported a patients who developed fulminant pneumococcal sepsis 12 years after successful treatment for Hodgkin's disease, which included splenic irradiation. We have since evaluated splenic size and function in 25 patients who had received splenic irradiation 5 to 16 years previously either for Hodgkin's disease (n . 19) or non-Hodgkin's lymphoma (n . 6). Mean maximum splenic diameter as measured on a 99mTc-sulfur colloid liver-spleen scan was 6.2 cm in the irradiated group and 9.7 cm in a control group (p less than 0.001). The mean percentage of erythrocytes containing pits when observed with interference phase microscopy was 13.0% in the irradiated group, which was significantly different (p less than 0.001) from the levels found in each of the control groups: normal subjects, 0.9%; unstaged and untreated lymphoma patients, 0.6%; and patients after splenectomy, 33.7%. Patients who have had splenic irradiation should be considered at risk of developing overwhelming pneumococcal sepsis

Irradiation effects on C/C composite materials for high temperature nuclear applications

International Nuclear Information System (INIS)

Eto, M.; Ugachi, H.; Baba, S.I.; Ishiyama, S.; Ishihara, M.; Hayashi, K.

2000-01-01

Excellent characteristics such as high strength and high thermal shock resistance of C/C composite materials have led us to try to apply them to the high temperature components in nuclear facilities. Such components include the armour tile of the first wall and divertor of fusion reactor and the elements of control rod for the use in HTGR. One of the most important aspects to be clarified about C/C composites for nuclear applications is the effect of neutron irradiation on their properties. At the Japan Atomic Energy Research Institute (JAERI), research on the irradiation effects on various properties of C/C composite materials has been carried out using fission reactors (JRR-3, JMTR), accelerators (TANDEM, TIARA) and the Fusion Neutronics Source (FNS). Additionally, strength tests of some neutron-irradiated elements for the control rod were carried out to investigate the feasibility of C/C composites. The paper summarises the R and D activities on the irradiation effects on C/C composites. (authors)

Present Status of the Wholesomeness of Irradiated Foods of Basic Interest to Developing Countries, in Particular to Those in the Asian and Pacific Regions

Energy Technology Data Exchange (ETDEWEB)

Aiyar, A. S. [Biochemistry and Food Technology Division, Bhabha Atomic Research Centre, Trombay, Bombay (India)

1981-09-15

Among the irradiated foods, the safety of which has already been unconditionally accepted by the Joint Expert Committee on Food Irradiation, are some that, as major items of food, are of considerable interest to the developing countries. However, the anticipated practical adoption of the technology has not taken place owing to the existence of technical and economic constraints. It would appear that the process offers greater promise for certain high-value items of food, e.g. frozen sea-foods, spices and tropical fruits for which conventional processing methods are inadequate to yield products that meet hygienic standards, especially of importing nations. The acceptance of such foods originating from developing countries by the industrialized importing countries could give a boost to food irradiation activities in the former. Most food irradiation applications in practice are likely to be combination processes involving the use of other chemical or physical agents, and the regulatory philosophy with respect to such treatments requires rationalization. It would be a stupendous task to establish experimentally the safety of the same food product subjected to different combination treatments; wholesomeness of the product subjected to a combination process cannot be inferred merely on the basis of each component of the combination treatment being individually recognized as yielding a wholesome product. Studies on the radiation chemistry of various classes of foods and model systems have served to emphasize their predictive value and have led to the concept of 'chemiclearance' for extrapolating wholesomeness from one food to another in the same general category. It should, however, be emphasized that excessive or undue reliance on the chemical data, coupled with the rigid attitude of some health authorities in respect of the presence of genetic toxicants (zero tolerance), could result in the absurd situation of the chemical approach invalidating the far more relevant

Experimental studies on prevention of trichinosis by food irradiation (Co60)

International Nuclear Information System (INIS)

Shimazu, Kimitaka

1993-01-01

A systemic study was performed to elucidate the effects of 60 Co irradiation on maturation or fecundity of Trichinella spiralis by assessing from parasitological, morphological and immunological points of view. Pieces of muscle tissue of mice infected with T. spiralis were irradiated with 60 Co at doses of 50, 75, 100, 150 and 200 Gy. These irradiated tissue (Experimental group) and non-irradiated tissues (Control group) were fed to healthy mice. Half of the mice were sacrificed 6 days after the ingestion. The number of adult worms were counted and subjected to statistical analysis, which disclosed a good correlation between the dose of 60 Co irradiation and worm damage; the higher the dose the more damage parasites had, and no adults were recovered if the tissue had been irradiated with more than 150 Gy prior to infection. The same tendency was true for the histopathology of the intenstines of host mice; the higher the dose the less tissue damage. Circulating antigens of T. spiralis and antibodies against T. spiralis were detected in every serum examined by ELISA. The remaining mice were sacrificed 30 days after the ingestion. The numbers of muscle larvae were counted and subjected to statistical analysis, which disclosed a good correlation between th dose of 60 Co irradiation and worm damage, and no larvae were recovered if the tissue had been irradiated with more than 75Gy. Higher concentrations of circulating antigens of T. spiralis and antibodies against T. spiralis were detected in the serum samples taken with muscle larvae. Thus this study established that 60 Co irradiation of more than 150 Gy caused complete damage on maturation, and that irradiation of more than 75 Gy caused complete damage on the fecundity of T. spimalis. (author)

Effect of linear polarized near-infrared light irradiation on flexibility of shoulder and ankle joints.

Science.gov (United States)

Demura, S; Yamaji, S; Ikemoto, Y

2002-12-01

There is a possibility that heat stimulus by linear polarized near-infrared light irradiation (PL: Super Lizer HA-30, Tokyo Medical Laboratory) improves the range of joint motion, because the flexibility of soft-part tissues, such as a muscle or a tendon, is improved by increasing the muscle temperature. The purpose of this study was to examine the influence of PL-irradiation on the ranges of shoulder and ankle motions. 30 healthy young adults (15 males: mean+/-SD, age 19.1+/-0.8 yrs, height 173.3+/-4.6 cm, body mass 68.5+/-8.0 kg and 15 females: mean+/-SD, age 19.2+/-0.7 yrs, height 162.3+/-4.5 cm, body mass 58.1+/-6.6 kg) participated in the experiment under PL-irradiation and no-irradiation (placebo) conditions. the angles of shoulder and ankle joint motions were measured twice, before and after the PL- and placebo-irradiations. The angle of a motion was defined as the angle connecting 3 points at linearity as follows: for the shoulder, the greater trochanter, acromion, and caput ulnare, and for the ankle, the knee joint, fassa of lateral malleolus and metacarpal bone. Each angle was measured when a subject extended or flexed maximally without support. The trial-to-trial reliability of each range of joint motion was very high. All parameters in PL-irradiation were significantly larger in postirradiation than pre-irradiation, and the value of postirradiation in PL-irradiation was significantly greater than that for placebo. The ranges of shoulder and ankle motions in placebo-irradiation were also significantly greater in postirradiation than pre-irradiation. Moreover, the change rate for each range of joint motion between pre- and postirradiations was significantly greater in PL-irradiation in both joints. In PL-irradiation, most subject's motions were greater in postirradiation than pre-irradiation, but not in the placebo-irradiation. The effect of PL-irradiation tended to be greater on subjects with a small range of a joint motion. It is considered from the

Miniature tensile test specimens for fusion reactor irradiation studies

International Nuclear Information System (INIS)

Klueh, R.L.

1985-01-01

Three miniature sheet-type tensile specimens and a miniature rod-type specimen are being used to determine irradiated tensile properties for alloy development for fusion reactors. The tensile properties of type 316 stainless steel were determined with these different specimens, and the results were compared. Reasonably good agreement was observed. However, there were differences that led to recommendations on which specimens are preferred. 4 references, 9 figures, 6 tables

Cranial irradiation alters dendritic spine density and morphology in the hippocampus.

Directory of Open Access Journals (Sweden)

Ayanabha Chakraborti

Full Text Available Therapeutic irradiation of the brain is a common treatment modality for brain tumors, but can lead to impairment of cognitive function. Dendritic spines are sites of excitatory synaptic transmission and changes in spine structure and number are thought to represent a morphological correlate of altered brain functions associated with hippocampal dependent learning and memory. To gain some insight into the temporal and sub region specific cellular changes in the hippocampus following brain irradiation, we investigated the effects of 10 Gy cranial irradiation on dendritic spines in young adult mice. One week or 1 month post irradiation, changes in spine density and morphology in dentate gyrus (DG granule and CA1 pyramidal neurons were quantified using Golgi staining. Our results showed that in the DG, there were significant reductions in spine density at both 1 week (11.9% and 1 month (26.9% after irradiation. In contrast, in the basal dendrites of CA1 pyramidal neurons, irradiation resulted in a significant reduction (18.7% in spine density only at 1 week post irradiation. Analysis of spine morphology showed that irradiation led to significant decreases in the proportion of mushroom spines at both time points in the DG as well as CA1 basal dendrites. The proportions of stubby spines were significantly increased in both the areas at 1 month post irradiation. Irradiation did not alter spine density in the CA1 apical dendrites, but there were significant changes in the proportion of thin and mushroom spines at both time points post irradiation. Although the mechanisms involved are not clear, these findings are the first to show that brain irradiation of young adult animals leads to alterations in dendritic spine density and morphology in the hippocampus in a time dependent and region specific manner.

Plant growth regulation by the light of LEDs; LED ko wo tsukatta shokubutsu saibai gijutsu

Energy Technology Data Exchange (ETDEWEB)

Watanabe, H. [Mitsubishi Chemical Co., Tokyo (Japan). Yokohama Research Center

1996-03-01

Light Emitting Diode (LED) has not only an excellent display function for the luminescent device but also a superior feature without other lamps as light source for plant growth. It was National Aeronautics and Space Administration (NASA) to find out such merit for this light source for plant growth and try at first to use for plant growth at the space. They began to examine the LED application to the light source for the plant growth at the space since a stage at high cost of the LED, to develop some researches centered at cultivation of lettuce, wheat, and others. Finding out future possibility of cost-down of the LEDs on the cost/performance and large merits of the LEDs for control of the plant growth and plant physiology, authors have conducted some cultivation experiments of the plants using the LEDs for light source some years ago. In this papers, characterizations, actual possibility, and future developments of the LEDs for the light sources of the plant growth, are introduced. 5 refs., 4 figs.

Irradiation monitoring of spices by chemiluminescence method

International Nuclear Information System (INIS)

Bhatti, K.A.; Khan, H.M.; Sattar, A.; Ahmad, A.

2001-01-01

Some spices (cumin, coriander, black pepper and red pepper), commonly used due to their specific aroma and nutritional value were studied using chemiluminescence (CL) method to test whether the food has been irradiated or not. The spices were ground to different mesh sizes and subjected to gamma ray doses of 2.5, 5.0, 7.5 and 10 Kgy. The effect of radiation doses and particle size on the CL response of irradiated and un-irradiated samples was checked using luminol and lucigenin sensitizers. The storage experiment was also performed for all spices with both the sensitizers in order to pick the suitable sensitizer for CL study. During this study Co-60 gamma ray source and Bio-orbit 1250 luminometer were used after precise calibration

Stem cell migration after irradiation

International Nuclear Information System (INIS)

Nothdurft, W.; Fliedner, T.M.

1979-01-01

The survival rate of irradiated rodents could be significantly improved by shielding only the small parts of hemopoietic tissues during the course of irradiation. The populations of circulating stem cells in adult organisms are considered to be of some importance for the homeostasis between the many sites of blood cell formation and for the necessary flexibility of hemopoietic response in the face of fluctuating demands. Pluripotent stem cells are migrating through peripheral blood as has been shown for several mammalian species. Under steady state conditions, the exchange of stem cells between the different sites of blood cell formation appears to be restricted. Their presence in blood and the fact that they are in balance with the extravascular stem cell pool may well be of significance for the surveilance of the integrity of local stem cell populations. Any decrease of stem cell population in blood below a critical size results in the rapid immigration of circulating stem cells in order to restore local stem cell pool size. Blood stem cells are involved in the regeneration after whole-body irradiation if the stem cell population in bone marrows is reduced to less than 10% of the normal state. In the animals subjected to partial-body irradiation, the circulating stem cells appear to be the only source for the repopulation of the heavily irradiated, aplastic sites of hemopoietic organs. (Yamashita, S.)

Menstrual restoration in severe panhypopituitarism many years after cranial irradiation for suprasellar germinoma.

Science.gov (United States)

Ito, Masanobu; Iwamoto, Ichiro; Hirano, Hirofumi; Douchi, Tsutomu

2015-07-01

We report a very rare case showing menstrual restoration in severe pan-hypopituitarism many years after cranial irradiation for suprasellar germinoma. A 30-year-old, almost primarily amenorrheic woman with severe panhypopituitarism presented with cyclic genital bleeding for the previous five months. She had menstruated once, when she was 13 years old. When she was 14 years old, she was diagnosed with a suprasellar germinoma measuring 10 mm in diameter, which led to diabetes insipidus. Cranial irradiation with a total dose of 24 Gy and chemotherapy resulted in complete tumor remission. She developed severe hypopituitarism [luteinizing hormone (LH) = 0.4 mIU/mL, follicle-stimulating hormone (FSH) = 1.7 mIU/mL, and serum estradiol (E2) level panhypopituitarism after cranial irradiation. A relatively low dose of irradiation and small tumor size may have contributed to the recovery of menstruation in our patient.

Irradiation risks for hospital staff working with radiotechnetium

International Nuclear Information System (INIS)

Heaton, B.; Brown, L.D.

1975-01-01

The handling of technetium-99m can lead to the irradiation of personnel during the five main stages of its use. Experience shows that the nurses and radiopharmacists are subjected to an exposure difficult to reduce below a certain threshold, but with adequate precautions and job rotation the dose received by the personnel is nevertheless very slight. The practicians themselves, who have been the centre of attention over the last few years, undergo a negligible irradiation [fr

Irradiation risks for hospital staff working with radiotechnetium

Energy Technology Data Exchange (ETDEWEB)

Heaton, B; Brown, L D [Aberdeen Univ. (UK)

1975-10-01

The handling of technetium-99m can lead to the irradiation of personnel during the five main stages of its use. Experience shows that the nurses and radiopharmacists are subjected to an exposure difficult to reduce below a certain threshold, but with adequate precautions and job rotation the dose received by the personnel is nevertheless very slight. The practicians themselves, who have been the centre of attention over the last few years, undergo a negligible irradiation.

The effect of irradiation on the DNA of cauliflower

International Nuclear Information System (INIS)

Harmey, M.A.

1991-01-01

The cellular DNA is one of the components most affected by ionizing radiation. Lesions caused range from single and double stranded breaks to chemical modification of bases depending on the radiation dosage and the metabolic status of the tissue. In attempting to assess the DNA damage induced by irradiation of vegetables in a speedy and convenient manner, we examined the effect on the DNA by subjecting cauliflower to a dose of 1 kGy. If DNA is nicked by irradiation, the extent of the damage can be assessed by using DNA polymerase to repair the nicks. Comparisons were made between irradiated and non irradiated cauliflower and incorporation of 32 p deoxy GTP in the presence of the Klenow fragment of DNA polymerase measured

Color homogeneity in LED spotlights

NARCIS (Netherlands)

Prins, C.R.; Tukker, T.W.; IJzerman, W.L.; Thije Boonkkamp, ten J.H.M.

2014-01-01

LED is a rising technology in the field of lighting. Halogen spotlights are nowadays replaced by LED spotlights because of their energy efficiency and long lifetime. However, color variation in the light output is a common problem. Poorly designed LED spotlights tend to have yellowish or bluish

Studies on some irradiated food products

International Nuclear Information System (INIS)

Mohammed, H.M.B.

1998-01-01

The aim of this investigation was to study the possibility of using some doses of gamma irradiation and cold storage (4+1 C) for improving the hygienic quality and shelf-life of some meat products ( beef luncheon, processed minced beef and fresh beef sausage). luncheon meat samples were irradiated at doses of 4,6,8,10 and 12 k Gy, while beef and sausage samples were subjected to 4,6 and 8 KGy gamma rays doses and the effects of irradiation on the organoleptic properties, microbiological aspects and the chemical composition were studied during cold storage (4+1 C) of samples. Attention was focussed on the changes occurred in the organoleptic properties of these products by the evaluation of sensory scores for appearance, color and odor of samples post irradiation and during cold storage (4+1 C). In addition, the effects of treatments and cold storage on the microbiological quality by the determination of total bacterial count, total psychropilic bacteria, total coliforms, total molds and yeasts, staphylococcus aureus, streptococcus faecalis as well as the detection of salmonellae were studied

LED lamp power management system and method

Science.gov (United States)

Gaines, James; Clauberg, Bernd; Van Erp, Josephus A. M.

2013-03-19

An LED lamp power management system and method including an LED lamp having an LED controller 58; a plurality of LED channels 60 operably connected to the LED controller 58, each of the plurality of LED channels 60 having a channel switch 62 in series with at least one shunted LED circuit 83, the shunted LED circuit 83 having a shunt switch 68 in parallel with an LED source 80. The LED controller 58 reduces power loss in one of the channel switch 62 and the shunt switch 68 when LED lamp electronics power loss (P.sub.loss) exceeds an LED lamp electronics power loss limit (P.sub.lim); and each of the channel switches 62 receives a channel switch control signal 63 from the LED controller 58 and each of the shunt switches 68 receives a shunt switch control signal 69 from the LED controller 58.

Detection of irradiated spices by thermoluminescence analysis

International Nuclear Information System (INIS)

Hammerton, K.M.; Banos, C.

1996-01-01

Spices are used extensively in prepared foods. The high levels of contamination of many spices with microorganisms poses a problem for the food industry. Irradiation treatment is the most effective means of reducing the microbial load to safe levels. Although the process is currently subject to a moratorium in Australia, it is used in several countries for the decontamination of spices. Methods for detecting irradiation treatment of spices are necessary to enforce compliance with labelling requirements or with a prohibition on the sale of irradiated foods. Thermoluminescence (TL) analysis of spice samples has been shown to be an applicable method for the detection of all irradiated spices. It was established that the TL response originates from the adhering mineral dust in the sample. Definitive identification of many irradiated spices requires the separation of a mineral extract from the organic fraction of the spice sample. This separation can be achieved by using density centrifugation with a heavy liquid, sodium polytungstate. Clear discrimination between untreated and irradiated spice samples has been obtained by re-irradiation of the mineral extract after the first TL analysis with an absorbed dose of about 1 kGy (normalisation). The ratio of the first to second TL response was about one for irradiated samples and well below one for untreated samples. These methods have been investigated with a range of spices to establish the most suitable method for routine control purposes. (author)

Steroidogenesis in the testes and the adrenals of adult male rats after γ-irradiation in utero at late pregnancy

International Nuclear Information System (INIS)

Suzuki, Keiko; Takahashi, Masakazu; Ishii-Ohba, Hiroko; Ikeda, Kiyomi; Inano, Hiroshi

1990-01-01

Pregnant rats were irradiated with 2.1Gy γ-ray of 60 Co at day 20 of gestation. Seventy days after birth, the body weight of the fetally irradiated male pups was significantly lower than the control. The testes, ventral prostates and seminal vesicles were atrophied by irradiation, whereas no decreased weight of the adrenals was observed. Histological examination of the testes of the irradiated rats revealed a complete disappearance of germinal cells. Sertoli cells and Leydig cells appeared normal, and no apparent histological difference was observed in the adrenals between the control and the irradiated rats. Examination of steroidgenesis in testes and adrenals led to the conclusion that irreversible damage was induced in spermatogenesis and androgen production by the fetal irradiation, whereas corticoidogenesis was not affected. (author)

Postirradiation examination results for the Irradiation Effects Scoping Test 2

International Nuclear Information System (INIS)

Mehner, A.S.

1977-01-01

The postirradiation examination results are reported for two rods from the second scoping test (IE-ST-2) of the Nuclear Regulatory Commission Irradiation Effects Program. The rods were irradiated in the in-pile test loop of the Power Burst Facility at the Idaho National Engineering Laboratory. Rod IE-005 was fabricated from fresh fuel and cladding previously irradiated in the Saxton Reactor. Rod IE-006, fabricated from fresh fuel and unirradiated cladding, was equipped with six developmental cladding surface thermocouples. The rods were preconditioned, power ramped, and then subjected to film boiling operation. The performance of the rods and the developmental thermocouples are evaluated from the post irradiation examination results. The effects of prior irradiation damage in cladding are discussed in relation to fuel rod behavior during a power ramp and subsequent film boiling operation

Experimental approach and micro-mechanical modeling of the mechanical behavior of irradiated zirconium alloys; Approche experimentale et modelisation micromecanique du comportement des alliages de zirconium irradies

Energy Technology Data Exchange (ETDEWEB)

Onimus, F

2003-12-01

Zirconium alloys cladding tubes containing nuclear fuel of the Pressurized Water Reactors constitute the first safety barrier against the dissemination of radioactive elements. Thus, it is essential to predict the mechanical behavior of the material in-reactor conditions. This study aims, on the one hand, to identify and characterize the mechanisms of the plastic deformation of irradiated zirconium alloys and, on the other hand, to propose a micro-mechanical modeling based on these mechanisms. The experimental analysis shows that, for the irradiated material, the plastic deformation occurs by dislocation channeling. For transverse tensile test and internal pressure test this channeling occurs in the basal planes. However, for axial tensile test, the study revealed that the plastic deformation also occurs by channeling but in the prismatic and pyramidal planes. In addition, the study of the macroscopic mechanical behavior, compared to the deformation mechanisms observed by TEM, suggested that the internal stress is higher in the case of irradiated material than in the case of non-irradiated material, because of the very heterogeneous character of the plastic deformation. This analysis led to a coherent interpretation of the mechanical behavior of irradiated materials, in terms of deformation mechanisms. The mechanical behavior of irradiated materials was finally modeled by applying homogenization methods for heterogeneous materials. This model is able to reproduce adequately the mechanical behavior of the irradiated material, in agreement with the TEM observations. (author)

Surface modification of ceramic materials induced by irradiation of high power pulsed ICP

International Nuclear Information System (INIS)

Ishigaki, Takamasa; Okada, Nobuhiro; Ohashi, Naoki; Haneda, Hajime

2003-01-01

Newly developed pulse-modulated high-power inductively coupled plasma [ICP] is expected to offer the unique physico-chemical condition, such as the increased concentration of chemically reactive species, as well as the appropriate heat flux for materials processing. Two kinds of oxide materials, titanium and zinc oxide, were placed at the downstream of Ar-H 2 ICP and irradiated in the plasma of continuous [CN] and pulse-modulated [PM] modes. The CN-ICP irradiation at the position close to the plasma tail gave rise to the thermal reduction of oxides. In the PM-ICP irradiation, the degree of thermal reduction depended on the lower power level during pulse-off time, as well as the total electric power. Irradiation in PM-ICP led to the increased formation of oxygen vacancies in titanium dioxide. In the case of zinc oxide, the UV emission efficiency was improved by PM-ICP irradiation, while the green emission became predominant by CN-ICP irradiation at the appropriate position. Induced effects in the two oxides by PM-ICP would be related to the high concentration of hydrogen radicals in the plasma. (author)

Lung Irradiation Increases Mortality After Influenza A Virus Challenge Occurring Late After Exposure

Energy Technology Data Exchange (ETDEWEB)

Manning, Casey M. [Department of Environmental Medicine, University of Rochester Medical Center, Rochester, New York (United States); Johnston, Carl J. [Department of Environmental Medicine, University of Rochester Medical Center, Rochester, New York (United States); Department of Pediatrics, University of Rochester Medical Center, Rochester, New York (United States); Reed, Christina K. [Department of Pediatrics, University of Rochester Medical Center, Rochester, New York (United States); Lawrence, B. Paige [Department of Environmental Medicine, University of Rochester Medical Center, Rochester, New York (United States); Department of Microbiology and Immunology, University of Rochester Medical Center, Rochester, New York (United States); Williams, Jacqueline P. [Department of Radiation Oncology, University of Rochester Medical Center, Rochester, New York (United States); Finkelstein, Jacob N., E-mail: Jacob_Finkelstein@urmc.rochester.edu [Department of Environmental Medicine, University of Rochester Medical Center, Rochester, New York (United States); Department of Pediatrics, University of Rochester Medical Center, Rochester, New York (United States); Department of Radiation Oncology, University of Rochester Medical Center, Rochester, New York (United States)

2013-05-01

Purpose: To address whether irradiation-induced changes in the lung environment alter responses to a viral challenge delivered late after exposure but before the appearance of late lung radiation injury. Methods and Materials: C57BL/6J mice received either lung alone or combined lung and whole-body irradiation (0-15 Gy). At 10 weeks after irradiation, animals were infected with 120 HAU influenza virus strain A/HKx31. Innate and adaptive immune cell recruitment was determined using flow cytometry. Cytokine and chemokine production and protein leakage into the lung after infection were assessed. Results: Prior irradiation led to a dose-dependent failure to regain body weight after infection and exacerbated mortality, but it did not affect virus-specific immune responses or virus clearance. Surviving irradiated animals displayed a persistent increase in total protein in bronchoalveolar lavage fluid and edema. Conclusions: Lung irradiation increased susceptibility to death after infection with influenza virus and impaired the ability to complete recovery. This altered response does not seem to be due to a radiation effect on the immune response, but it may possibly be an effect on epithelial repair.

Biochemical changes on the repair of surgical bone defects grafted with biphasic synthetic micro-granular HA + β-tricalcium phosphate induced by laser and LED phototherapies assessed by Raman spectroscopy

Science.gov (United States)

Pinheiro, Antonio Luiz B.; Soares, Luiz Guilherme P.; Marques, Aparecida Maria C.; Silveira, Landulfo

2016-03-01

This work aimed the assessment of the biochemical changes during bone mineralization induced by laser and LED irradiation in an animal model of bone repair using a spectral model based on Raman spectroscopy. Six groups were studied: Clot, Laser (λ780 nm, 70 mW), LED (λ850 nm +/- 10 nm, 150 mW), Biomaterial (biphasic synthetic microgranular hydroxyapatite (HA) + β-tricalcium phosphate), Laser + Biomaterial and LED + Biomaterial. When indicated, defects were further irradiated at 48 h interval during 2 wks, 20 J/cm2 per session. At 15th and 30th days, femurs were dissected and spectra of the defects were collected. Raman spectra were submitted to a model to estimate the relative amount of collagen, phosphate HA and carbonate HA, by using spectra of pure collagen, biomaterial and basal bone, respectively. At 15th days, the use of biomaterial associated to phototherapy reduced the collagen formation, whereas the amount of carbonate HA was not different in all groups. The phosphate HA was higher in the groups that received biomaterial grafts. At 30th days, it was observed an increase of collagen for the group Laser + Biomaterial, and a reduction in the carbonate HA for the LED + Biomaterial. The phosphate HA was higher for the groups LED + Biomaterial and Laser + Biomaterial, while decreased for the group Biomaterial. These results indicated that the use of Laser and LED phototherapies improved the repair of bone defects grafted with the biomaterial by increasing the collagen deposition and phosphate HA.

Seasonal variability in irradiance affects herbicide toxicity to the marine flagellate Dunaliella tertiolecta

Directory of Open Access Journals (Sweden)

Sascha eSjollema

2014-06-01

Full Text Available Photosynthetically Active Radiation (PAR and Ultraviolet Radiation (UVR of the solar spectrum affect microalgae directly and modify the toxicity of phytotoxic compounds present in water. As a consequence seasonal variable PAR and UVR levels are likely to modulate the toxic pressure of contaminants in the field. Therefore the present study aimed to determine the toxicity of two model contaminants, the herbicides diuron and Irgarol®1051, under simulated irradiance conditions mimicking different seasons. Irradiance conditions of spring and autumn were simulated with a set of Light Emitting Diodes (LEDs. Toxicity of both herbicides was measured individually and in a mixture by determining the inhibition of photosystem II efficiency (ΦPSII of the marine flagellate Dunaliella teriolecta using Pulse Amplitude Modulation (PAM fluorometry. Toxicity of the single herbicides was higher under simulated spring irradiance than under autumn irradiance and this effect was also observed for mixtures of the herbicides. This irradiance dependent toxicity indicates that herbicide toxicity in the field is seasonally variable. Consequently toxicity tests under standard light conditions may overestimate or underestimate the toxic effect of phytotoxic compounds.

Report on the investigational study on the technical trend of temperature control materials for high efficiency LED lighting use; Kokoritsu LED shomeiyo no ondo seigyo zairyo no gijutsu doko ni kansuru chosa kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of the innovative conservation of lighting use energy, a project is being promoted with the aim of developing light emitted diode (LED) and commercializing lighting use light source substituting for fluorescent light. In this study, the following were conducted: literature survey on Peltier materials as temperature control materials for high efficiency LED lighting and the making of them as elements, extraction of technical subjects in the commercialization of LED cooling use Peltier element materials, market surveys/analyses were made of the fields of application including the LED cooling use field. As a result, for the commercialization of temperature control use Peltier elements of lighting use LED, the desirable performance index is 5x10{sup -5}/K or more. Bi{sub 2}Te{sub 3} elements which are now commercially available as Peltier elements are not good in performance and have the toxicity problem. As a candidate of temperature control use materials of lighting use LED, Mg{sub 2} (Sn, Si) or clathrate system are regarded, but the point, etc. were pointed out that it is necessary to improve thermoelectric characteristics. (NEDO)

Phase transformations in lithium aluminates irradiated with neutrons

International Nuclear Information System (INIS)

Carrera, L.M.; Delfin L, A.; Urena N, F.; Basurto, R.; Bosch, P.

2003-01-01

The lithium aluminate like candidate to be used in the coverings producers of tritium in the fusion nuclear reactors, presents high resistance to the corrosion to the one to be stuck to structural materials as special steels. However, the crystallographic changes that take place in the cover that is continually subjected to irradiation with neutrons, can alter its resistance to the corrosion. In this work the changes of crystalline structure are shown that they present two types of nano structures of lithium aluminates, subjected to an average total dose 7.81 x 10 8 Gy in the fixed irradiation system of capsules of the one TRIGA Mark lll nuclear reactor of the Nuclear Center of Mexico. The studied nano structures presented only phase transformations without formation of amorphous material. (Author)

Regulatory aspects of food irradiation in the Asia-Pacific region

International Nuclear Information System (INIS)

Roberts, Peter B.

2000-01-01

The latest information on the countries in the Asia/Pacific region with approvals for food to be irradiated is provided. Differences in the type of regulations used are contrasted. However, progress has been made towards greater uniformity in regulations based around the Codex General Standard for Irradiated Food. Australia and New Zealand instituted, respectively, a moratorium and a ban on food irradiation in 1988. Australia has proposed a new draft Standard for food irradiation and this is the subject of public discussion under the Australia New Zealand Food Authority. The draft Standard is a prohibition with the possibility of exemptions being given on a case-by-case basis. Some details of the draft Standard are provided. (author)

Are nurse-led chemotherapy clinics really nurse-led? : an ethnographic study

OpenAIRE

Farrell, Carole; Walshe, Catherine Elizabeth; Molassiotis, Alex

2017-01-01

Background: The number of patients requiring ambulatory chemotherapy is increasing year on year, creating problems with capacity in outpatient clinics and chemotherapy units. Although nurse-led chemotherapy clinics have been set up to address this, there is a lack of evaluation of their effectiveness. Despite a rapid expansion in the development of nursing roles and responsibilities in oncology, there is little understanding of the operational aspects of nurses’ roles in nurse-led clinics. Ob...

What can we learn from Raman Spectroscopy on irradiation-induced defects in UO2?

International Nuclear Information System (INIS)

Desgranges, L.; Martin, Ph.; Simon, P.; Guimbretiere, G.; Baldinozzi, G.

2014-01-01

Recent results on irradiated UO 2 by Raman spectroscopy evidenced Raman lines that are characteristic of irradiation-induced defects. Three main mechanisms are identified to explain their origin: resonant Raman, formation of new molecular entities, or breakdown in symmetry. Arguments are given to consider breakdown in symmetry as the predominant mechanism. A tentative description of the defects at the origin of this symmetry breakdown is proposed in terms of coordination polyhedrons of uranium. This discussion led us to consider that the Raman defect modes could be related to area with different stoichiometry. (authors)

Ineffectiveness of a fluorometric method for identifying irradiated food base on thymine glycol

International Nuclear Information System (INIS)

Ewing, D.D.; Stepanik, T.M.

1992-01-01

At dosages used for food irradiation, some of the thymine present in the DNA of irradiated food may be converted to thymine glycol. A fluorometric assay for thymine glycol was investigated as a possible method of detecting irradiated foods based on this effect. Experiments were performed on homogenates of irradiated chicken breast meat and on DNA isolated from irradiated chicken breast meat. In both cases the assay was subject to interference from one of the reagents, o-aminobenzaldehyde, and lacked the necessary sensitivity to detect the thymine glycol produced by radiolysis of the DNA at relevant dosages

Evaluation of Mechanical Properties of Glass Fiber Posts Subjected to Laser Surface Treatments.

Science.gov (United States)

Barbosa Siqueira, Carolina; Spadini de Faria, Natália; Raucci-Neto, Walter; Colucci, Vivian; Alves Gomes, Erica

2016-10-01

The aim of this study was to evaluate the influence of laser irradiation on flexural strength, elastic modulus, and surface roughness and morphology of glass fiber posts (GFPs). Laser treatment of GFPs has been introduced to improve its adhesion properties. A total of 40 GFPs were divided into 4 groups according to the irradiation protocol: GC-no irradiation, GYAG-irradiation with erbium:yttrium-aluminum-garnet [Er:YAG], GCR-irradiation with erbium, chromium:yttrium-scandium-gallium-garnet (Er,Cr:YSGG), and GDI-irradiation with diode laser. The GFP roughness and morphology were evaluated through laser confocal microscopy before and after surface treatment. Three-point bending flexural test measured flexural strength and elastic modulus. Data about elastic modulus and flexural strength were subjected to one-way ANOVA and Bonferroni test (p properties of GFPs.

Effects of postpolymerization microwave irradiation on provisional dental acrylics: physical and mechanical properties.

Science.gov (United States)

Ozkomur, Ahmet; Fortes, Carmen Beatriz Borges

2016-07-26

This study aimed to evaluate the effects of microwave irradiation on the physical and mechanical properties of poly(methyl methacrylate) (PMMA) provisional resins. Twenty bars and 20 disc-shaped specimens were fabricated for each selected provisional restorative material (Dencor and Duralay). Test groups were subjected to microwave irradiation (3 minutes at 600 W) after polymerization. Bar specimens were subjected to a flexural strength test. Disc-shaped specimens were used to evaluate microhardness. Backscattered Raman spectroscopy was employed for each group to define the degree of conversion of the monomer/polymer. The frequency bands corresponding to C = C and C = O groups were used to determine the conversion of methyl methacrylate (MMA) monomers into polymers. Glass transition temperature was determined using a differential scanning calorimeter. Microwave irradiation of both tested autopolymerizing PMMA provisional materials resulted in a statistically significant increase in microhardness, degree of conversion and glass transition temperature values. Also, the results demonstrated a significant increase in flexural strength after postpolymerization microwave irradiation for the Dencor specimens. It is concluded that mechanical and physical properties are positively influenced by microwave irradiation.