Environmental Pollution, Toxicity Profile and Treatment Approaches for Tannery Wastewater and Its Chemical Pollutants.

Science.gov (United States)

Saxena, Gaurav; Chandra, Ram; Bharagava, Ram Naresh

Leather industries are key contributors in the economy of many developing countries, but unfortunately they are facing serious challenges from the public and governments due to the associated environmental pollution. There is a public outcry against the industry due to the discharge of potentially toxic wastewater having alkaline pH, dark brown colour, unpleasant odour, high biological and chemical oxygen demand, total dissolved solids and a mixture of organic and inorganic pollutants. Various environment protection agencies have prioritized several chemicals as hazardous and restricted their use in leather processing however; many of these chemicals are used and discharged in wastewater. Therefore, it is imperative to adequately treat/detoxify the tannery wastewater for environmental safety. This paper provides a detail review on the environmental pollution and toxicity profile of tannery wastewater and chemicals. Furthermore, the status and advances in the existing treatment approaches used for the treatment and/or detoxification of tannery wastewater at both laboratory and pilot/industrial scale have been reviewed. In addition, the emerging treatment approaches alone or in combination with biological treatment approaches have also been considered. Moreover, the limitations of existing and emerging treatment approaches have been summarized and potential areas for further investigations have been discussed. In addition, the clean technologies for waste minimization, control and management are also discussed. Finally, the international legislation scenario on discharge limits for tannery wastewater and chemicals has also been discussed country wise with discharge standards for pollution prevention due to tannery wastewater.

Solutions for energy recovery of animal waste from leather industry

International Nuclear Information System (INIS)

Lazaroiu, Gheorghe; Pană, Constantin; Mihaescu, Lucian; Cernat, Alexandru; Negurescu, Niculae; Mocanu, Raluca; Negreanu, Gabriel

2017-01-01

Highlights: • Animal fats in blend with diesel fuel for energy valorification through combustion. • Animal waste from tanneries as fuel and for biogas production. • Experimental tests using animal fats as fuel for diesel engines. • Experimental tests modifying the characteristic parameters. - Abstract: Secondary products from food and leather industries are regarded as animal wastes. Conversion of these animal wastes into fuels represents an energy recovery solution not only because of their good combustion properties, but also from the viewpoint of supply stability. A tannery factory usually processes 60–70 t/month of crude leathers, resulting in 12–15 t/month of waste. Fats, which can be used as the input fuel for diesel engines (in crude state or as biodiesel), represent 10% of this animal waste, while the rest are proteins that can be used to generate biogas through anaerobic digestion. Herein, we analyse two approaches to the use of animal waste from tanneries: as fuel for diesel engines and for biogas generation for heat production. Diesel fuelling and fuelling by animal wastes are compared in terms of the engine performance and pollutant emissions. The effects of animal waste usage on the pollutant emissions level, exhaust gas temperature, indicated mean effective pressure, maximum pressure, and engine efficiency are analysed. The energy recovery technologies for animal waste, which are analysed in this work, can be easily implemented and can simultaneously solve the problem posed by animal wastes by using them as an alternative to fossil fuels. Animal fats can be considered an excellent alternative fuel for diesel engines without major constructive modifications.

EVALUATION OF LEATHER QUALITY AND ECOTOXICITY IN SIMULATED TANNERY WASTEWATERS USING MIMOSA TANNIN

Directory of Open Access Journals (Sweden)

ÇELİK Cem

2016-05-01

Full Text Available The leather tanning industry is characterized by the production of different kinds of effluents, generated in each step of leather processing. These effluents have various chemical compounds which may cause toxicity and endocrine disruption and are thus known as endocrine disrupting chemicals (EDC. Tanning stabilizes the protein structure of the hide and imparts heat stability, enhanced tensile properties, and resistance to microbial degradation. Currently most high quality leather is "chrome-tanned," produced by treatment of the hide with salts of the mineral chromium. In this study, the wastewater characteristics and ecotoxicity before and after tanning and retanning processes using mimosa tannin are assessed. Vegetable leather production procedure was followed using one dose mimosa tannin. Leather quality was evaluated according to standard methods. Wastewater characteristics showed that mimosa contributed high organic content to the wastewater. Although vegetable tannin was used the effluent toxicity was observed in tanning and retanning effluents. The preliminary results also showed that leather quality tests failed or at minimum level to comply with the standard values indicating that there is still a need to optimize the procedure including mimosa dose. This study was designed to produce eco-friendly leather using mimosa in tanning and retanning processes. Leather quality and the ecotoxicity of each process during leather production was assessed according to standard methods.

Chromium fractionation and plant availability in tannery-sludge amended soil

Science.gov (United States)

Allué, Josep; Moya Garcés, Alba; Bech, Jaume; Barceló, Juan; Poschenrieder, Charlotte

2013-04-01

The leather industry represents an important economic sector in both developed and developing countries. Chromium tanning is the major process used to obtain high quality leather. Within the REACH regulation the use of Cr, especially CrVI, in the tanning process is under discussion in Europe. High Cr concentration in shoes and other Cr-tanned leather products can cause contact dermatitis in sensitive population. Moreover, the high Cr concentration is the major limiting factor for the use of tannery sludge as a source of organic matter in agricultural soils. Interest in Cr, however is not limited to its potential toxic effects. Chromium III is used as a dietary supplement because there are reports, but also controversy, about the positive effects of Cr III in glucose tolerance and type-2 diabetes. Adequate intake levels for Cr by the diet have been established between 25 and 35 µg/day for adult females and males, respectively. Sufficient supply of Cr III by the diet is preferable to the use of CrIII-salt based dietary supplements. The objective of the present work was to investigate whether Cr from tannery sludge-amended soil is available to Trigonella foenum-graecum plants, a plant used both as a spice and as a medicinal herb, because of its hypoglucemic effects. For this purpose clay loam soil (pH 7.8) was sieved (2mm) and thoroughly mixed with tannery sludge from a depuration station (Igualadina Depuració i Recuperació S.L., Igualada, Barcelona, Spain). The sludge had a Cr concentration of 6,034mg kg-1 and a 0.73 % of NH4-nitrogen. All the Cr was in the form of CrIII. Three treatments were disposed. Control soil receiving no sludge, a 60 mg kg-1 Cr treatment (10 g fresh sludge kg-1 soil) and a 120 mg kg-1 Cr treatment (20 g fresh sludge kg-1 soil). Control soil and the soil treated with 10g kg-1 sludge received NPK fertilizer in the form of ammonium sulfate, superfosfate, and KCl to rise the N,P, and K concentrations to similar levels to those achieved in the

Determination of vegetable tannins in tannery wastewater using RP-HPLC-technique with UV- and EC-detection; Bestimmung vegetabiler Gerbstoffe in Gerbereiabwasser unter Einsatz der RP-HPLC-Technik mit UV- und EC-Detektion

Energy Technology Data Exchange (ETDEWEB)

Zywicki, B.; Reemtsma, T.; Jekel, M. [Technische Univ. Berlin (Germany). Fachgebiet Wasserreinhaltung

2001-07-01

Numerous types of inorganic and organic environmental pollutants are encountered in leather tannery effluents. For reduction of the environmental impact of leather tanneries the substitution of chromium tanning agents by natural organic tanning agents (vegetable tannins) is discussed. The use of vegetable tannins leads to an elevated dissolved organic carbon content (DOC) in tannery effluent, even after biological treatment. Vegetable tannins may also be used as retanning agents, but they may, then interfere with precipitation of chromium. Therefore, an analytical method had to be established to estimate the total amount of vegetable tanning agents in the complex matrix of tannery wastewater. The analytical strategy for the determination of vegetable tannins in tannery effluents is to degrade the polyphenolic compounds by acid hydrolysis and to detect the resulting specific monomeric subunit gallic acid by RP-HPLC-technique with UV- and electrochemical detection (EC-detection). (orig.)

Occupational allergic contact dermatitis and patch test results of leather workers at two Indonesian tanneries

NARCIS (Netherlands)

Febriana, Sri Awalia; Jungbauer, Frank; Soebono, Hardyanto; Coenraads, Pieter-Jan

Background. Tannery workers are at considerable risk of developing occupational contact dermatitis. Occupational skin diseases in tannery workers in newly industrialized countries have been reported, but neither the prevalence of occupational allergic contact dermatitis nor the skin-sensitizing

Assessment of Physicochemical and Biochemical Qualities of Tannery Effluents of Hazaribagh, Dhaka, and Comparison with Non-Tannery Water Samples

Directory of Open Access Journals (Sweden)

Laila N. Islam

2015-02-01

Full Text Available NOTE: on 21st May 2015, the authors Mahmud Hossain and M Mohasin were added to the online information about the article. The PDF remains correct.In this study the physicochemical and biochemical qualities of the tannery effluents were analyzed to determine the pollution load of the openly released wastewaters in the environment and the findings were compared with the non-tannery waters. Fourteen samples of factory effluents were collected from the leather tanning industrial zone of Hazaribagh, Dhaka, and 13 non-tannery water samples were collected from different parts of Dhaka city. The effluents were mostly colored; their pH varied from highly acidic to basic values while densities were not much different from the non-tannery waters. The chromium contents of the effluents varied from less than 0.002 to 18.97 mg/L and the chemical oxygen demands (COD varied from 90 to 6500 mg/L, which were significantly higher than those of non-tannery waters. There was a strong direct correlation between chromium content and COD (p<0.01 indicating that chromium was hugely responsible for pollution caused by tannery effluents. The tannery wastewaters were highly toxic to brine shrimp nauplii (lethality: about 82%, and chromium was responsible for biotoxicity of the effluents since a direct significant correlation (p<0.021 was found between chromium content and lethality. Storage of the wastewater samples for 2 to 8 months at room temperature showed rise in the pH values possibly due to microbial action that resulted in decrease of dissolved chromium content from a mean value of 7.94 to 5.09 mg/L. These findings demonstrated that the presence of high concentrations of chromium and other chemicals in the untreated tannery effluents were contributing adverse effects on the environment and ecosystem.DOI: http://dx.doi.org/10.3126/ije.v4i1.12179International Journal of Environment Volume-4, Issue-1, Dec-Feb 2014/15, page: 68-81  

Simultaneously Recovering High-Purity Chromium and Removing Organic Pollutants from Tannery Effluent

Directory of Open Access Journals (Sweden)

Jie Zong

2016-01-01

Full Text Available Chromium pollution is a serious issue because of carcinogenic toxicities of the pollutants and low recovery rate of chromium because of the presence of organic, such as protein and fat. In this work, high recovery rate and high purity of the chromium ion were successfully prepared by the way of acid enzyme, flocculant, and Fenton oxidation. The experiments were characterized by TG, TOC, UV-VIS, and SEM. In the work, the tannery waste chrome liquor was used as experimental material. The results showed that the percentage of reduction of TOC in the tannery waste chrome liquor by method of Fenton oxidation, acid enzyme, and the flocculant was 71.15%, 65.26%, and 22.05%, respectively. Therefore, the organism content of chrome tanning waste liquid was greatly reduced through the pretreatment. And the application experiment showed that the properties and grain surface and fibers of the tanned leather with commercial chromium powder and chrome tanning agent prepared from the chromium waste liquid treated with Fenton are nearly the same.

Speciation of Chromium in Bottom Ash Obtained by the Incineration of the Leather Waste Shavings

OpenAIRE

k. louhab; H. Assas

2006-01-01

The evolution of bottom ash morphology and chromium metals behavior during incineration of a leather waste shavings at different incineration temperature have been studied. The Cr, Ca, Mg, Cl rates in bottom ashes, flay ashes and emitted gases in different incineration temperature of the tannery wastes are also determined. The morphology of the bottom ashes obtained by incineration at different temperature from the leather waste shavings was examined by MEB. The result sho...

Treatment of tanneries waste water by ultrasound assisted electrolysis process

International Nuclear Information System (INIS)

Farooq, R.; Ahmed, Z.; Gilani, M. A.; Durrani, M.; Mahmood, Q.; Shaukat, S. F.; Choima, N.

2013-01-01

The leather industry is a major producer of wastewater and solid waste containing potential water and soil contaminants. Considering the large amount and variety of chemical agents used in skin processing, the wastewaters generated by tanneries are very complex. Therefore, the development of treatment methods for these effluents is extremely necessary. In this work the electrochemical treatment of a tannery wastewater by ultrasound assisted electrochemical process, using stainless steel and lead cathode and titanium anodes was studied. Effect of ultrasound irradiation at various ultrasonic intensities 0, 40, 60 and 80% on electrochemical removal of chromium was investigated. Experiments were conducted at two pH conditions of pH 3 and 9. Significant removal of chromium was found at pH 3 and it was also noticed that by increasing ultrasonic intensities, percentage removal of chromium and sulfate also increases. The optimum removal of chromium and sulfate ions was observed at 80% ultrasonic intensity. The technique of electrolysis assisted with ultrasonic waves can be further improved and can be the future waste water treatment process for industries. (author)

Using Scenedesmus sp. for the Phycoremediation of Tannery Wastewater

OpenAIRE

Ballén-Segura, Miguel; Hernández Rodríguez, Luisa; Parra Ospina, David; Vega Bolaños, Asly; Pérez, Karen

2016-01-01

Wastewater from the leather tannery industry contains high concentrations of heavy metals, especially chromium, as well as high values of inorganic nutrients and organic matter which, if not treated prior to discharge, may alter the quality of surface water bodies. As an alternative treatment to these industrial effluents, we propose the use of microalgae, due to their ability to remove contaminants. This study evaluates the growth of the microalga Scenedesmus sp. in three different dilutions...

Mohawk Tannery Hazardous Waste Site in New Hampshire included on EPA List of Targeted for Immediate Attention

Science.gov (United States)

Today, the U.S. Environmental Protection Agency released the list of Superfund sites that Administrator Pruitt has targeted for immediate and intense attention. The former Mohawk Tannery facility (a.k.a. Granite State Leathers) is one of the 21 sites on th

Tannery sludge disposal: Materials recovery feasibility. Problematiche dello smaltimento dei fanghi di conceria

Energy Technology Data Exchange (ETDEWEB)

Tiravanti, G. (Consiglio Nazionale delle Ricerche, Bari (Italy). Ist. di Ricerca sulle Acque); Santori, M. (Consiglio Nazionale delle Ricerche, Rome (Italy). Ist. di Ricerca sulle Acque)

1993-02-01

Tannery industries utilize chromium as a main leather tanning material. The exhaustion yield of tanning baths is generally between 50-60% and this implies high quantities of chromium, a precious raw material, discharged into the wastes. The tannery wastewater treatment plants in Italy generate about 280,000 t/year of sludges containing as much as 5% of chromium, whose disposal is not an easy task. This paper describes some data on tanning sludge chemical characterization and current disposal possibilities. Moreover, some processes, developed at IRSA, based on the extraction of metals from the sludge in acidic media and their treatment with selective ion exchange resins, are illustrated. Such processes allow the recovery and recycling of raw materials, minimizing the production of wastes.

Characterization of tannery sludge from the leather industry of Franca industrial district, SP, Brazil

International Nuclear Information System (INIS)

Chambi, M.M.; Toffoli, S.M.

2011-01-01

The industry of leather manufacture generates large quantities of solid leather waste with characteristics of high-polluting and hazardous conditions. Among these wastes, stands out the wet blue leather (chromed leather scraps), and the tanning sludge and secondary sludge generated in the processes of effluents treatment. These wastes contain Cr(III), which, under oxidizing conditions, can turn into Cr (VI), which is highly toxic. However, these wastes are a potential source of chromium oxide (traditional industrial pigment), which could be used by the glass and ceramic enamel industries. In this study, a preliminary characterization of a chromium sludge from the industrial district of Franca-SP was conducted. X-ray diffraction (XRD), chemical (XRF) and thermal (DTA / TG) analyses were used to determine the physical and chemical characteristics of this solid waste. The potential of using this material as an available and cheap pigment for the manufacture of enamels and glass is discussed. (author)

Cancer incidence in the Swedish leather tanning industry: updated findings 1958-99.

Science.gov (United States)

Mikoczy, Z; Hagmar, L

2005-07-01

To assess how a 10 year extension of the follow up period affected cancer incidence in the Swedish leather tanning cohort. A cohort of 2027 tannery workers (of which 482 were women) who had been employed for at least one year between 1900 and 1989 at one of three Swedish leather tanneries, was established. The start of observation varied between 1958 and 1966 for the three plants. Through linkage with the Swedish Cancer Registry, incident cancer cases were recorded up to 1999. Cause specific expected cancer incidence was calculated for 1958-99 based on calendar year, sex, and five year age group specific incidence rates for the counties where the plants had been located. Altogether 56,022 person-years at risk were generated. A total of 351 incident cancer cases were observed compared to 302 expected, which resulted in an increased standardised incidence ratio (SIR) of 1.16 (95% CI 1.04 to 1.29). An enhanced risk for prostate cancer was observed (SIR 1.44, 95% CI 1.10 to 1.86), mainly attributable to the later part of the observation period (1990-99). In this updated analysis the previously observed risk excess for soft tissue sarcomas was no longer significant (SIR 2.62, 95% CI 0.96 to 5.70). For multiple myelomas and sinonasal cancer the slight non-significant excesses remained, still based on very few cases. The increased risk for prostate cancer in the present study might be a chance finding, but is noteworthy, since it is in acccordance with the finding of increased SIR for prostate cancer among leather workers in another recent Swedish study. Moreover, excess risks for prostate cancer among farmers have been reported, indicating pesticides as possible causative agents. Leather tanners have also been exposed to pesticides.

Hypertension in leather tanning workers working in Istanbul, Turkey.

Science.gov (United States)

Ince, N; Işsever, H; Ince, H; Ozyildirim, B; Işik, E; Hapçioğlu, B; Ozdilli, K; Akçay, M E; Calak, B; Agkoç, N

2008-11-01

Leather tanning may result in various occupational diseases. The aim of this study was to compare the relation between blood pressure levels and vocations in leather tanning. Our study was conducted in Turkey's leading leather process plant located in Tuzla organised industry zone, between March 11 and May 30, 2005. All leather plants that consented to participate in our study were included. The blood pressure, height and weight of the workers were measured. Their ages, educational levels, smoking habits and hypertension history were obtained via interviewing the subjects. The relation between three main factors, i.e. age, body mass index (BMI), working period, and hypertension were analysed through multiple logistic regression analysis. 40.4 percent (295) of 730 workers' blood pressure values were found to be within normal limits. 59.6 percent (435) were found to be hypertensive. The hypertension correlation remained significant, along with BMI and their working period (p-values were 0.0001 and 0.035, respectively). Our study demonstrated that BMI and working period have a key influence on the increased risk of hypertension, which leads us to consider the importance of occupational exposure. Different hypertension studies to be conducted in various occupational fields would likely be able to confirm our findings.

Removal of chromium hexavalent of residual water from tannery using hydrotalcite; Remocion de cromo hexavalente de aguas residuales de teneria utilizando hidrotalcita

Energy Technology Data Exchange (ETDEWEB)

Martinez G, S.; Martinez, V.; Bulbulian, S. [Instituto nacional de Investigaciones Nucleares, A.P. 18-1027, C.P. 11801 Mexico D.F. (Mexico)

2000-07-01

One of the main problems of leather tanned is the treatment that must be give to the waste water polluted with chrome which stays in trivalent form, but it is easily oxidated at chromium hexavalent. This work pretends to find an elimination media for chromium (VI) from water using the original synthetic hydrotalcite and calcined as sorbent by its anion exchange and memory effect properties. The tannery water was characterized by X-ray diffraction, thermal gravimetric analysis, specific surface and infrared spectroscopy. (Author)

Diversity of chromate resistant bacteria present in the tannery of fez in Morocco

International Nuclear Information System (INIS)

Essahale, A.; Malki, M.; Amils, R.; Moumni, M.; Marin, I.

2009-01-01

One of the main sources of income of Morocco is the leather goods made by craftsmen with tanned and tinted animal skins. One of the more important tanneries of Morocco is that located at the Medina of Fez, which constitutes on of the sources for heavy metals contamination of the Sebou River, since wastewater treatments are either in existent or inefficient and obsolete because the high costs required for their improvement. (Author)

Cancer incidence in the Swedish leather tanning industry: updated findings 1958–99

Science.gov (United States)

Mikoczy, Z; Hagmar, L

2005-01-01

Aims: To assess how a 10 year extension of the follow up period affected cancer incidence in the Swedish leather tanning cohort. Methods: A cohort of 2027 tannery workers (of which 482 were women) who had been employed for at least one year between 1900 and 1989 at one of three Swedish leather tanneries, was established. The start of observation varied between 1958 and 1966 for the three plants. Through linkage with the Swedish Cancer Registry, incident cancer cases were recorded up to 1999. Cause specific expected cancer incidence was calculated for 1958–99 based on calendar year, sex, and five year age group specific incidence rates for the counties where the plants had been located. Altogether 56 022 person-years at risk were generated. Results: A total of 351 incident cancer cases were observed compared to 302 expected, which resulted in an increased standardised incidence ratio (SIR) of 1.16 (95% CI 1.04 to 1.29). An enhanced risk for prostate cancer was observed (SIR 1.44, 95% CI 1.10 to 1.86), mainly attributable to the later part of the observation period (1990–99). In this updated analysis the previously observed risk excess for soft tissue sarcomas was no longer significant (SIR 2.62, 95% CI 0.96 to 5.70). For multiple myelomas and sinonasal cancer the slight non-significant excesses remained, still based on very few cases. Conclusions: The increased risk for prostate cancer in the present study might be a chance finding, but is noteworthy, since it is in acccordance with the finding of increased SIR for prostate cancer among leather workers in another recent Swedish study. Moreover, excess risks for prostate cancer among farmers have been reported, indicating pesticides as possible causative agents. Leather tanners have also been exposed to pesticides. PMID:15961622

Complex mixture-associated hormesis and toxicity: the case of leather tanning industry.

Science.gov (United States)

Pagano, Giovanni; Castello, Giuseppe; Gallo, Marialuisa; Borriello, Ilaria; Guida, Marco

2008-01-01

A series of studies investigated the toxicities of tannery-derived complex mixtures, i.e. vegetable tannin (VT) from Acacia sp. or phenol-based synthetic tannin (ST), and waste-water from tannin-based vs. chromium-based tanneries. Toxicity was evaluated by multiple bioassays including developmental defects and loss of fertilization rate in sea urchin embryos and sperm (Paracentrotus lividus and Sphaerechinus granularis), and algal growth inhibition (Dunaliella tertiolecta and Selenastrum capricornutum). Both VT and ST water extracts resulted in hormetic effects at concentrations ranging 0.1 to 0.3%, and toxicity at levels > or =1%, both in sea urchin embryo and sperm, and in algal growth bioassays. When comparing tannin-based tannery wastewater (TTW) vs. chromium-based tannery effluent (CTE), a hormesis to toxicity trend was observed for TTW both in terms of developmental and fertilization toxicity in sea urchins, and in algal growth inhibition, with hormetic effects at 0.1 to 0.2% TTW, and toxicity at TTW levels > or =1%. Unlike TTW, CTE showed a monotonic toxicity increase from the lowest tested level (0.1%) and CTE toxicity at higher levels was significantly more severe than TTW-induced toxicity. The results support the view that leather production utilizing tannins might be regarded as a more environmentally friendly procedure than chromium-based tanning process.

SMART BIOCONVERSION OF PELT WASTE FROM TANNERIES

Directory of Open Access Journals (Sweden)

ZAINESCU Gabriel

2017-05-01

Full Text Available The area of interest is the synthesis and study of properties of new types of hydrogels made from pelt waste, in order to recover waste from tanneries. Leather processing in tanneries results in about 500-600 kg of pelt waste from a ton of raw hides. These hydrogels are made using smart processes in order to then be applied in agriculture, for preservation of water in the soil or for controlled release of fertilizers, pesticides but also for the development of additivated agricultural film biodegradable over time (between 1 month and 6 months. Hydrogels that are based on biopolymers, compared with hydrogels based on synthetic polymers, have the advantage of biodegradability, biocompatibility, and a low level of toxicity. The paper presents the production of biodegradable polymer mixtures obtained from hydrolysis and enrichment of the resulting hydrolysate with phosphorus and potassium. Hydrogels with collagenous structure are tested using a high-performance instrumental analysis system (FT-IR-ATR, UV-VIS-NIR, SEM, EDAX, etc. The paper presents an experimental model for obtaining hydrogels with collagenous structure from pelt waste resulting from the liming process.

Latex peptidases of Calotropis procera for dehairing of leather as an alternative to environmentally toxic sodium sulfide treatment.

Science.gov (United States)

Lopéz, Laura M I; Viana, Carolina A; Errasti, María E; Garro, María L; Martegani, José E; Mazzilli, Germán A; Freitas, Cléverson D T; Araújo, Ídila M S; da Silva, Rafaela O; Ramos, Márcio V

2017-09-01

Dehairing of crude leather is a critical stage performed at the beginning of its processing to obtain industrially useful pieces. Tanneries traditionally apply a chemical process based on sodium sulfide. Since this chemical reactive is environmentally toxic and inefficiently recycled, innovative protocols for reducing or eliminating its use in leather depilation are welcomed. Therefore, latex peptidases from Calotropis procera (CpLP) and Cryptostegia grandiflora (CgLP) were assayed for this purpose. Enzyme activity on substrates representative of skin such as hide powder azure (U HPA ), elastin (U E ), azocollagen (U AZOCOL ), keratin (U K ), and epidermis (U EP ) was determined, while depilation activity was assayed on cow hide. Only CpLP was active against keratin (13.4 U K ) and only CgLP was active against elastin (0.12 U E ). CpLP (93.0 U HPA , 403.6 U AZOCOL , 36.3 U EP ) showed higher activity against the other substrates than CgLP (47.6 U HPA , 261.5 U AZOCOL , 8.5 U EP ). In pilot assays, CpLP (0.05% w/v with sodium sulfite 0.6% w/v as activator) released hairs from cow hide pieces. Macroscopic and microscopic analyses of the hide revealed that the dehairing process was complete and the leather structure was preserved. The proteolytic system of C. procera is a suitable bioresources to be exploited by tanneries.

Studies on quality of sub-surface water around tanneries in some areas of north west frontier province (NWFP) Pakistan

International Nuclear Information System (INIS)

Nasreen, S.

2003-01-01

The present study is a part of our investigations comprising (a) characterization of the tannery/leather industry effluents, (b) assessment of the pollution caused by these effluents to the environment, and (c) development of a simple but economical procedure for the pre-treatment and recycling of these effluents, to recover some valuable materials. In NWFP, the tanning industry has shown a rapid development in the late seventies, during which large-size industrial units were established at Peshawar, Charsadda and Jehangira. Since no pollution control measures are being adopted by these units, the hazards to the environment caused by the effluents and emissions from tanneries pose an acute problem in the country. The studies narrated below indicate that the under-ground water samples around tanneries have high concentrations of TDS, phenols, chromium and sulfides, which render the well-water in the area unsuitable for drinking and domestic uses. (author)

ASSESSMENT OF TANNERY BASED SOLID WASTES MANAGEMENT IN ASILI, NAIROBI KENYA

Directory of Open Access Journals (Sweden)

Richard O. Oruko

2014-06-01

Full Text Available Solid wastes generated in Nairobi and its environs are posing a serious environmental challenge to the authorities and public, especially the hazardous and non-biodegradable solid wastes from leather industries. There were environmental concerns and complaints from workers and residents living adjacent to Asili tanneries limited about degradation of natural and inbuilt environment. This pointed to the effect of environmental pollution by the tannery. The broad objective of study was to assess the effectiveness of tannery based solid wastes management, by identifying and analyzing the concentration levels of sodium chlorides,sulphide, chromium ions and total phenols as selected pollutants along the tanning stages, in Nairobi river, borehole water, and soils around the dump site inside the tannery. Experimental (laboratory analysis design was used.Descriptive statistics was used in analyzing data resulting in means and tables. The means concentration of total Chrome was 2633.38mg/L,Sodium chloride 609.93mg/L, Sulphide 129.77mg/L, total Phenols 10.91mg/L in the soil sampled around the composite dump site.. In Nairobi river water the means of Sodium chloride was 317.48mg/L, Sulphide 24.00mg/L, total Phenol 3.97mg/L and total Chrome Nil, While means concentration in borehole water, had Sodium chloride detected at 354.73mg/L, Sulphide 6.67mg/L, total Phenol 0.03mg/L and total Chrome as Nil, indicating heavily contaminated ecosystems above the discharge set limits of National Environmental Management Authority and Nairobi city water and sewerage company.

Characterization of Wastewaters obtained from Hatay Tanneries

Directory of Open Access Journals (Sweden)

Şana Sungur

2017-06-01

Full Text Available The leather tanning industry is one of the most significant pollutants in terms of both conventional and toxic parameters. On the other hand, leather industry has an important economic role both in Turkey and in the World. In this study, wastewater samples were taken from 15 different tanneries in the Hatay Region. Wastewaters obtained from liming process and chromium tanning process was analyzed. Sulfide, chromium (III, chromium (VI, oil and grease, total suspended solids (TSS, organic matters, biochemical oxygen demand (BOD, chemical oxygen demand (COD, pH and alkalinity were determined according to Turkish Standard Methods. The determined averages values belong to wastewaters obtained from liming process were as following: pH 11.71; COD 16821 mg L-1; BOD 4357 mg L-1; TSS 39023 mg L-1; oil and grease 364 mg L-1; S-2 concentration 802 mg L-1; alkalinity 2115 mg L-1. The determined averages values belong to wastewaters obtained from chromium tanning process were also as following: pH 4.23; COD 6740 mg L-1; BOD 377 mg L-1; Cr+3 concentrations 372 mg L-1; Cr+6 concentrations 127 mg L-1; TSS 14553 mg L-1; oil and grease 343 mg L-1. The results of all analyzes were higher than wastewater discharge standards. As a result, it’s necessary to use more effective treatments in order to reduce the negative impacts of leather tanning industry that affect environment, natural water resources and at last human health and welfare.

Cancer incidence and specific occupational exposures in the Swedish leather tanning industry: a cohort based case-control study.

Science.gov (United States)

Mikoczy, Z; Schütz, A; Strömberg, U; Hagmar, L

1996-01-01

OBJECTIVE--To study the effect on the incidence of cancer of exposure to chemicals handled in the leather tanning industry. MATERIALS AND METHODS--A case-control study was performed within a cohort of 2487 workers employed for at least six months during the period 1900-89 in three Swedish leather tanneries. 68 cancer cases (lung, stomach, bladder, kidney, nasal, and pancreatic cancers and soft tissue sarcomas) and 178 matched controls were studied. Effects of chemical exposures on cancer incidence, adjusted for age at risk, sex, and plant were estimated with a conditional logistic regression model. RESULTS--A significant association was found between exposure to leather dust and pancreatic cancer (odds ratio (OR) 7.19, 95% confidence interval (95% CI) 1.44 to 35-89). An association was indicated between leather dust from vegetable tanning and lung cancer. After adjustment for smoking habits a tentative association between organic solvents and lung cancer lost its significance. No association was found between exposure to chlorophenols and soft tissue sarcomas. CONCLUSIONS--The significant association between leather tanning and soft tissue sarcomas that was found in our previous cohort analysis could not be explained by exposure to chlorophenols. On the other hand a significant association was found between exposure to leather dust and pancreatic cancer, and exposure to leather dust from vegetable tanning was often present in cases with lung cancer. Due to the small numbers of cases, the results can, however, only lead to tentative conclusions. PMID:8704870

Sono-leather technology with ultrasound: a boon for unit operations in leather processing - review of our research work at Central Leather Research Institute (CLRI), India.

Science.gov (United States)

Sivakumar, Venkatasubramanian; Swaminathan, Gopalaraman; Rao, Paruchuri Gangadhar; Ramasami, Thirumalachari

2009-01-01

Ultrasound is a sound wave with a frequency above the human audible range of 16 Hz to 16 kHz. In recent years, numerous unit operations involving physical as well as chemical processes are reported to have been enhanced by ultrasonic irradiation. There have been benefits such as improvement in process efficiency, process time reduction, performing the processes under milder conditions and avoiding the use of some toxic chemicals to achieve cleaner processing. These could be a better way of augmentation for the processes as an advanced technique. The important point here is that ultrasonic irradiation is physical method activation rather than using chemical entities. Detailed studies have been made in the unit operations related to leather such as diffusion rate enhancement through porous leather matrix, cleaning, degreasing, tanning, dyeing, fatliquoring, oil-water emulsification process and solid-liquid tannin extraction from vegetable tanning materials as well as in precipitation reaction in wastewater treatment. The fundamental mechanism involved in these processes is ultrasonic cavitation in liquid media. In addition to this there also exist some process specific mechanisms for the enhancement of the processes. For instance, possible real-time reversible pore-size changes during ultrasound propagation through skin/leather matrix could be a reason for diffusion rate enhancement in leather processing as reported for the first time. Exhaustive scientific research work has been carried out in this area by our group working in Chemical Engineering Division of CLRI and most of these benefits have been proven with publications in valued peer-reviewed international journals. The overall results indicate that about 2-5-fold increase in the process efficiency due to ultrasound under the given process conditions for various unit operations with additional benefits. Scale-up studies are underway for converting these concepts in to a real viable larger scale operation. In

Reduction of COD in wastewater from an organized tannery industrial region by Electro-Fenton process

International Nuclear Information System (INIS)

Kurt, Ugur; Apaydin, Omer; Gonullu, M. Talha

2007-01-01

Advanced oxidation processes (AOPs) have led the way in the treatment of aqueous waste and are rapidly becoming the chosen technology for many applications. In this paper, COD reduction potential of leather tanning industry wastewaters by Electro-Fenton (EF) oxidation, as one of the AOPs, was experimentally evaluated. The wastewater sample was taken from an outlet of an equalization basin in a common treatment plant of an organized tannery industrial region in Istanbul, Turkey. Treatment of the wastewater was carried out by an electrochemical batch reactor equipped with two iron electrodes, which were connected parallel to each other. The oxidation process was studied for optimization of H 2 O 2 and the electricity consumptions were observed at different contact times under different pH conditions (3.0, 5.0 and 7.2). In each case, electricity consumption for decreased COD mass was estimated. In this process, COD was reduced by 60-70% within 10 min. By taking into consideration the local sewerage discharge limit, applicability of EF process for the tannery wastewaters was evaluated

Reduction of COD in wastewater from an organized tannery industrial region by Electro-Fenton process

Energy Technology Data Exchange (ETDEWEB)

Kurt, Ugur [Yildiz Technical University, Environmental Engineering Department, 34349 Istanbul (Turkey)]. E-mail: ukurt@yildiz.edu.tr; Apaydin, Omer [Yildiz Technical University, Environmental Engineering Department, 34349 Istanbul (Turkey)]. E-mail: apaydin@yildiz.edu.tr; Gonullu, M. Talha [Yildiz Technical University, Environmental Engineering Department, 34349 Istanbul (Turkey)]. E-mail: gonul@yildiz.edu.tr

2007-05-08

Advanced oxidation processes (AOPs) have led the way in the treatment of aqueous waste and are rapidly becoming the chosen technology for many applications. In this paper, COD reduction potential of leather tanning industry wastewaters by Electro-Fenton (EF) oxidation, as one of the AOPs, was experimentally evaluated. The wastewater sample was taken from an outlet of an equalization basin in a common treatment plant of an organized tannery industrial region in Istanbul, Turkey. Treatment of the wastewater was carried out by an electrochemical batch reactor equipped with two iron electrodes, which were connected parallel to each other. The oxidation process was studied for optimization of H{sub 2}O{sub 2} and the electricity consumptions were observed at different contact times under different pH conditions (3.0, 5.0 and 7.2). In each case, electricity consumption for decreased COD mass was estimated. In this process, COD was reduced by 60-70% within 10 min. By taking into consideration the local sewerage discharge limit, applicability of EF process for the tannery wastewaters was evaluated.

Enhanced production of Aspergillus tamarii lipase for recovery of fat from tannery fleshings

Directory of Open Access Journals (Sweden)

A. Dayanandan

2013-12-01

Full Text Available The influence of various oil cakes has been investigated for high level production of lipase using Aspergillus tamarii MTCC 5152. By solid state fermentation in wheat bran containing 2.5% w/w gingili oil cake at 70% v/w moisture content the fungus produced a maximal yield of lipase (758 ± 3.61 u/g after 5 days of incubation using 2% v/w inoculum containing 10(6 spores/mL. Wheat bran and gingili oil cake with supplementation of gingili oil (1.0% w/w, glucose (0.5% w/w and peptone (0.5% w/w gives an increased enzyme production of 793 ± 6.56 u/g. The enzyme shows maximum activity at pH 7.0, temperature 50 °C and was stable between the pH 5.0-8.0 and temperature up to 60 °C. Crude lipase (3% applied to tannery fleshing shows 92% fat solubility. The results demonstrate that fat obtained from tannery fleshing, a by-product of the leather industry has a high potential for biodiesel production and the proteinaceous residue obtained can be used as animal feed.

Determinants of Leather and Leather products Exports in Tanzania

Directory of Open Access Journals (Sweden)

Francis Lwesya

2018-03-01

Full Text Available This study examines the determinants of Leather and Leather products Exports in Tanzania. We apply Ordinary Least Square (OLS analysis on time series data from 1980 to 2015. The findings show that export of raw hides and skins, and high costs of production are among the deterring factors to leather and leather products export in Tanzania. Export of raw hides and skins and costs of production recorded negative and significant relationship with leather exports. On the other hand, hides and skins collection recorded insignificant relationship while leather price in the world market had negative and significant relationship with leather exports. This suggests that other factors such as low quality of leather and leather products exported, inadequate capital investment, stiff competition with foreign companies for hides and skins and inadequate market information explain the state of current Tanzania’s leather exports. Thus, attracting local and Foreign Direct Investment (FDI in the leather subsector by providing friendly investment climate and addressing the supply side constraints will enable increased high quality leather and leather products diversification and exports

REMOVAL OF HEAVY-METALS FROM WASTEWATER USING A ...

African Journals Online (AJOL)

This work is licensed under the Creative Commons Attribution 4.0 International License. REMOVAL ... containing wastewaters obtained from a tannery and a leather processing industries revealed excellent adsorption efficacies ... the heavy-metal loading in test industrial effluents obtained from a leather industry and from a.

Metagenomic profiling of antibiotic resistance genes and mobile genetic elements in a tannery wastewater treatment plant.

Directory of Open Access Journals (Sweden)

Zhu Wang

Full Text Available Antibiotics are often used to prevent sickness and improve production in animal agriculture, and the residues in animal bodies may enter tannery wastewater during leather production. This study aimed to use Illumina high-throughput sequencing to investigate the occurrence, diversity and abundance of antibiotic resistance genes (ARGs and mobile genetic elements (MGEs in aerobic and anaerobic sludge of a full-scale tannery wastewater treatment plant (WWTP. Metagenomic analysis showed that Proteobacteria, Firmicutes, Bacteroidetes and Actinobacteria dominated in the WWTP, but the relative abundance of archaea in anaerobic sludge was higher than in aerobic sludge. Sequencing reads from aerobic and anaerobic sludge revealed differences in the abundance of functional genes between both microbial communities. Genes coding for antibiotic resistance were identified in both communities. BLAST analysis against Antibiotic Resistance Genes Database (ARDB further revealed that aerobic and anaerobic sludge contained various ARGs with high abundance, among which sulfonamide resistance gene sul1 had the highest abundance, occupying over 20% of the total ARGs reads. Tetracycline resistance genes (tet were highly rich in the anaerobic sludge, among which tet33 had the highest abundance, but was absent in aerobic sludge. Over 70 types of insertion sequences were detected in each sludge sample, and class 1 integrase genes were prevalent in the WWTP. The results highlighted prevalence of ARGs and MGEs in tannery WWTPs, which may deserve more public health concerns.

Ecotoxicological risks associated with tannery effluent wastewater.

Science.gov (United States)

Shakir, Lubna; Ejaz, Sohail; Ashraf, Muhammad; Qureshi, Naureen Aziz; Anjum, Aftab Ahmad; Iltaf, Imran; Javeed, Aqeel

2012-09-01

The problem of water pollution acquires greater relevance in the context of a developing agrarian economy like Pakistan. Even though, the leather industry is a leading economic sector in Pakistan, there is an increasing environmental concern regarding tanneries because they produce large amounts of potentially toxic wastewater containing both trivalent and hexavalent chromium, which are equally hazardous for human population, aquaculture and agricultural activities in the area. Therefore, we defined the scope of the present study as to employ different bioassays to determine the eco-toxic potential of tannery effluent wastewater (TW) and its chromium based components, i.e., potassium dichromate (K(2)Cr(2)O(7)) and chromium sulfate Cr(2)(SO(4))(3). Particle-induced X-ray emission (PIXE) analysis of TW was carried out to determine the concentration of chromium in TW and then equal concentrations of hexavalent (K(2)Cr(2)O(7)) and trivalent chromium Cr(2)(SO(4))(3) were obtained for this study. Cytotoxicity assay, artemia bioassay and phytotoxicity assay was utilized to investigate the eco-toxicological potential of different concentrations of TW, K(2)Cr(2)O(7) and Cr(2)(SO(4))(3). All the dilutions of TW, K(2)Cr(2)O(7) and Cr(2)(SO(4))(3) presented concentration dependent cytotoxic effects in these assays. The data clearly represents that among all three tested materials, different dilutions of K(2)Cr(2)O(7) caused significantly more damage (P<0.001) to vero cell, brine shrimp and germination of maize seeds. Interestingly, the overall toxicity effects of TW treated groups were subsequent to K(2)Cr(2)O(7) treated group. Based on biological evidences presented in this article, it is concluded that hexavalent chromium (K(2)Cr(2)O(7)) and TW has got significant eco-damaging potential clearly elaborating that environmental burden in district Kasur is numerous and high levels of chromium is posing a considerable risk to the human population, aquaculture and agricultural

SUSTAINABLE ENVIRONMENTAL TECHNOLOGIES INCLUDING WATER RECOVERY FOR REUSE FROM TANNERY AND INDUSTRIAL WASTEWATER – INDIAN AND ASIAN SCENARIO

Directory of Open Access Journals (Sweden)

Dr. S. RAJAMANI

2017-05-01

Full Text Available World leather sector generates 600million m3 of wastewater per annum. The Asian tanneries contributes more than 350 million m3 of wastewater from the process of 8 to 10 millions tons of hides and skins. Environmental challenges due to depletion of quality water resources and increase in salinity, it has become necessary to control Total Dissolved Solids (TDS in the treated effluent with water recovery wherever feasible. Adoption of special membrane system has been engineered in many individual and Common Effluent Treatment Plants (CETPs in India, China and other leather producing countries. The sustainability of saline reject management is one of the major challenges. Conventional tannery wastewater treatment systems include physiochemical and biological treatment to reduce Chromium, BOD, COD and Suspended Solids. To tackle treated effluent with TDS in the rage of 10000 to 30000mg/l, multiple stage high pressure membrane units have been designed and implemented for recovery of water. To reduce the chemical usage and sludge generation in the tertiary treatment, Membrane Bio-Reactor (MBR has been adopted which replace secondary clarifier and sophisticated tertiary treatment units such as Reactive Clarifier, Ultra-filtration (UF, etc. Commercial scale high-tech membrane systems have been implemented in many locations for the capacities ranging from 500 to 10000m3/day. Recent applied R&D on the environmental protection techniques with focus on water-recovery for reuse, salt recovery, marine disposal of saline reject with proper bio-control system, etc. are dealt in this novel technical paper.

Power ultrasound-assisted cleaner leather dyeing technique: influence of process parameters.

Science.gov (United States)

Sivakumar, Venkatasubramanian; Rao, Paruchuri Gangadhar

2004-03-01

be halved when ultrasound is employed to promote dyeing. Scanning electron microscopy analysis of the cross section of the dyed leather indicates that fiber structure is not affected due to the use of ultrasound under the given process conditions. The present study clearly demonstrates that ultrasound can be used as a tool to improve the rate of exhaustion of dye, reduce pollution load in the spent effluent liquor, and improve the quality of leather produced. The study also offered provision to employ optimum levels of chemicals and increases percentage exhaustion for a given time, thereby limiting the pollution load in the tannery effluent, which is of great social concern.

Chromium evaluation in work atmospheres in an industry of tanneries and one of galvanoplasty

International Nuclear Information System (INIS)

Agudelo V, Sonia; Duarte Martha

1994-01-01

In tannery and galvanoplasty industries situated in Bogota (Colombia) hexavalent chromium and total soluble chromium were determinate in air samples in order to evaluated occupational exposition and risks for the worker of these factories. Samples were collected by suction pumps located near the breathing space of workers using PVC filters as captors. Samples were collected following the methodology of partial consecutive periods. Determination of Cr (VI) was done calorimetrically. Total soluble chromium was determinate by flame atomic absorption, previous optimization of procedures. Results for tannery Cr (VI) are located in the range non-detectable to 9.4 /m3 total soluble chromium was found between non detectable and 74.0 /m3. Cr (VI) in galvanoplasty varies between non detectable and 500 /m3. Probability of occupational risk were found in tannery and galvanoplasty industries

Corporate carbon footprint for country Climate Change mitigation: A case study of a tannery in Turkey.

Science.gov (United States)

Kılıç, Eylem; Puig, Rita; Zengin, Gökhan; Zengin, Candaş Adıgüzel; Fullana-I-Palmer, Pere

2018-09-01

Assessment of carbon emissions and environmental impact of production is indispensable to achieve a sustainable industrial production in Turkey, especially for those companies willing to compete in new international green markets. In this case study, corporate carbon footprint of a representative Turkish tanning company was analyzed. Inventory and impact data are presented to help in the environmental decision-making process. The results indicate that significant environmental impacts were caused during the landfilling of solid wastes as well as the production of the electricity and fuel required in the tannery. Turkish tannery inventory data presented here for the first time will be useful for leather tanning company managers to calculate sustainability key indicators. Improving alternatives at country level were identified (increasing the renewable sources on electricity production and promote energy recovery in landfills) which would be useful not only to decrease greenhouse gas (GHG) emissions of tanning sector but also of other industries requiring electricity and producing organic wastes. Considering the substantial contribution of industrial processes to the Turkish carbon emissions (15.7%) (TUIK, 2013), work done on those areas would provide a sound improvement in environmental profile of Turkey. The importance to promote a national strategy to reduce GHG emissions in Turkey was discussed here, as well as its relation to corporate carbon footprint assessments. One of the significant points revealed from the case study is the lack of published country specific emission factors for Turkey, which is a fundamental prerequisite to promote corporate carbon footprint assessment within the country. Copyright © 2018 Elsevier B.V. All rights reserved.

GROWTH AND NODULATION OF LEUCAENA AND PROSOPIS SEEDLINGS IN SOIL PLUS TANNERY SLUDGE

Directory of Open Access Journals (Sweden)

Ademir Sérgio Ferreira de Araújo

2006-01-01

Full Text Available The objective of this paper was to evaluate the growth and nodulation of Leucaena and Prosopis seedlings in soil plus tannery sludge. The study was conducted in a greenhouse, using bags containing soil plus tannery sludge. Seedlings of Leucaena and Prosopis inoculated with Bradyrhizobium sp were used. Results were evaluated 90 days after plant emergency. The application of tannery sludge, in the rate of 11.250 kg per hectare significantly increased plant height, stem diameter, and above ground dry mass ofLeucaena. Regarding Prosopis, there were no significant increases in these variables with tannery sludge application, except for aerial dry mass. No significant differences were seen between the treatments with sludge and inoculated with Bradyrhizobium sp. as to nodule number and dry mass. Tannery sludge evaluated in this work did not affect nodulation, besides favoring Leucaena and Prosopis seedling growth.

Cytotoxicity, Genotoxicity, and Phytotoxicity of Tannery Effluent Discharged into Palar River Basin, Tamil Nadu, India

Directory of Open Access Journals (Sweden)

Suki Roy

2015-01-01

Full Text Available Ambur, a town located on the banks of Palar River, is considered one of the most polluted areas in India and occupied by hundreds of tanneries and leather product units. The present study was designed to evaluate the toxic effect of discharged tannery effluent (TE on model agricultural crops, ecofriendly microorganisms, and human blood cells. The phytotoxic effects of TE tested on Allium cepa and Lemna minor revealed inhibition of root growth and significant reduction in number of fronds, protein, and chlorophyll content. Moreover, TE induced chlorosis and tissue necrosis in Nostoc muscorum at low concentration (10%. TE has also negative impact on ecofriendly microorganisms, Bacillus thuringiensis, Rhizobium etli, and Aspergillus terreus which play an important role in the nutrition of plant growth. The genotoxicity of TE was investigated in human leukocytes which showed interference with normal mitotic division with subsequent cell lysis. It also intervened with the normal replication process and induced micronucleus formation in the healthy leukocyte. 5% concentration of TE has been revealed to be toxic to erythrocytes. From this study TE found in the Palar River of Ambur has adverse effects on all the three levels of organisms in ecosystem even at lower concentrations.

Cytotoxicity, Genotoxicity, and Phytotoxicity of Tannery Effluent Discharged into Palar River Basin, Tamil Nadu, India

Science.gov (United States)

Roy, Suki; Nagarchi, Lubbnaz; Das, Ishita; Mangalam Achuthananthan, Jayasri; Krishnamurthy, Suthindhiran

2015-01-01

Ambur, a town located on the banks of Palar River, is considered one of the most polluted areas in India and occupied by hundreds of tanneries and leather product units. The present study was designed to evaluate the toxic effect of discharged tannery effluent (TE) on model agricultural crops, ecofriendly microorganisms, and human blood cells. The phytotoxic effects of TE tested on Allium cepa and Lemna minor revealed inhibition of root growth and significant reduction in number of fronds, protein, and chlorophyll content. Moreover, TE induced chlorosis and tissue necrosis in Nostoc muscorum at low concentration (10%). TE has also negative impact on ecofriendly microorganisms, Bacillus thuringiensis, Rhizobium etli, and Aspergillus terreus which play an important role in the nutrition of plant growth. The genotoxicity of TE was investigated in human leukocytes which showed interference with normal mitotic division with subsequent cell lysis. It also intervened with the normal replication process and induced micronucleus formation in the healthy leukocyte. 5% concentration of TE has been revealed to be toxic to erythrocytes. From this study TE found in the Palar River of Ambur has adverse effects on all the three levels of organisms in ecosystem even at lower concentrations. PMID:26839546

Combined oxidative and biological treatment of separated streams of tannery wastewater

Energy Technology Data Exchange (ETDEWEB)

Vidal, G.; Nieto, J. [Environmental Science Center EULA - Chile, Univ. of Concepcion, Concepcion (Chile); Mansilla, H.D. [Lab. of Renewable Resources, Univ. of Concepcion, Concepcion (Chile); Bornhardt, C. [Chemical Engineering Dept., Univ. of La Frontera, Temuco (Chile)

2003-07-01

Leather tanning effluents are a source of severe environmental impacts. In particular, the unhairing stage, belonging to the beamhouse processes, generates an alkaline wastewater with high concentrations of organic matter, sulphides, suspended solids, and salts, which shows significant toxicity. The objective of this work was to evaluate the biodegradation of this industrial wastewater by combined oxidative and biological treatments. An advanced oxidation process (AOP) with Fenton's reagent was used as batch pre-treatment. The relationships of H{sub 2}O{sub 2}/Fe{sup 2+} and H{sub 2}O{sub 2}/COD were 9 and 4, respectively, reaching an organic matter removal of about 90%. Subsequently, the oxidised beamhouse effluent was fed to an activated sludge system, at increasing organic load rates (OLR), in the range of 0.4 to 1.6 g COD/L.d. The biological organic matter removal of the pre-treated wastewater ranged between 35% and 60% for COD, and from 60% to 70% for BOD. Therefore, sequential AOP pretreatment and biological aerobic treatment increased the overall COD removal up to 96%, compared to 60% without pretreatment. Bioassays with D. magna and D. pulex showed that this kind of treatment achieves only a partial toxicity removal of the tannery effluent. (orig.)

The Finnish background report for the EC documentation of best available techniques for tanning industry

Energy Technology Data Exchange (ETDEWEB)

Kustula, V.; Salo, H.; Witick, A.; Kaunismaa, P.

2000-08-01

The objective of this document is to identify best available techniques (BAT) for the reduction of emissions and energy use in the tanning industry in Finland. The leather tanning industry in Finland has long traditions, dating back for centuries, but today there are only nine tanneries of any importance left. The tanneries vary in size from small, family-owned ones to large on a Finnish scale, with a staff of about 70 persons. The production of finished leather in even the largest tannery in Finland is well below the production limit (12 tonnes finished leather a day) mentioned in the IPPC-directive (96/61/EC). The range of products manufactured by the Finnish leather industry is large and includes processed leather for, e.g. footwear, clothing, furniture and intermediate products, e.g. wet-blue and crust. The hides and skins of cows, lamb, elk, reindeer and occasionally skins from other animals, e.g. horses are the main raw materials used. Some of the tanneries carry out only a part of the processing and sell their products in a treated, but not finished state. Tanneries which undertake only a part of the preparation process are reviewed in this document as well. Because of the varying size of the Finnish tanneries, the quality and quantity of emissions and environmental impacts vary considerably. The parameters used by the authorities are suspended solids (SS), biological oxygen demand (BOD), and chromium and sulphide concentration in the effluents. The quantity of waste and waste water generated is also subject to assessment by the authorities. Direct regulation of emissions is practised in Finland by issuing permits containing emission limit values. Major waste streams generated are sludge from waste water treatment plants, animal residues from the beamhouse stage, residues from tanned leather and chemicals used. Various ways of residue separation and consequently reuse and recovery are practised in most Finnish tanneries. The proteinaceous residues from the

Natural rubber: leather composites

OpenAIRE

Ravichandran,K.; Natchimuthu,N.

2005-01-01

Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have ...

EXAMINING COMFORT PROPERTIES OF LEATHER and ARTIFICIAL LEATHER COVER MATERIALS

Directory of Open Access Journals (Sweden)

ÇETİN Münire Sibel

2016-05-01

Full Text Available The analysis and regulation of workplace, working instruments, the comfort of office chair, business environment (sound, lighting, climate, vibration, temperature, and humidity, work and break times, analysis and editing of the organization, are some of the topics of interest of ergonomics. Environmental impact and conditions have important role on the employee’s working comfortably and efficiently. Therefore these conditions need to be aligned to the human body nature. Unsuitable working conditions (noise, etc. cause additional load, which the human body endures, and this additional load reveals the signs of tiredness in the body. Even an office environment, unsuitable physical environment impairs health of workers and reduces the performance. Therefore, office climate, environmental factors such as lighting and noise must be harmonized with the employee’s body nature in all working environments. Seating comfort is one of the important factors affecting the performance of employees in the office environment. There are so many studies about chair dimensions and the disorders on human body which were caused by the inappropriate chair dimensions and sitting positions. However, there are a spot of studies about the surface of the chair and the discomfort caused by the chair cover and its negative performance effects. In this study, some results of seat cover analysis for the design of an ergonomic chair. Recently, ease of cleaning, low cost advantages caused the increasing of the use of artificial leather especially on the surface of the seat used in offices. The physical properties of natural leather and artificial leather were compared as the candidate covers to be used on the design of an ergonomic office chair.

Catastrophic Health Expenditure and Impoverishment Effects of Out-of-pocket Expenses: A Comparative Study of Tannery and Non-tannery Workers of Kanpur, India.

Science.gov (United States)

Kashyap, Gyan C; Singh, Shri K; Sharma, Santosh K

2018-01-01

Treatment-seeking behaviors and economic burden because of health expenditure are widely discussed issues in India, and more so in recent times. The aim of this study is to identify health problems of tannery workers and their treatment-seeking behavior and their health expenditure. The primary data used in this article were collected through a cross-sectional household survey of 284 male tannery workers in the Jajmau area of Kanpur city in the state of Uttar Pradesh, during January-June 2015. Findings of the study revealed that around 36% of the tannery workers and 42% of non-tannery workers received treatment as outpatients in government/municipal hospital in the first spell of treatment. The secondary source of treatment was pharmacy/drug stores for 30% of the tannery workers and 24% of the non-tannery workers, an indication that a substantial proportion takes treatment without consulting a qualified medical practitioner; it also highlights that almost one-third of the tannery and non-tannery workers visited private health facility despite poor economic condition. It is evident that a substantial proportion of tannery and non-tannery workers are visiting private/non-governmental organization/trust hospital despite their poor financial situation. There is an urgent need to reinstate people's faith in public health facilities by developing professionalism, integrity, and accountability among different levels of health functionaries and frontline workers with the support of credible, transparent, and responsible regulatory environment.

Catastrophic Health Expenditure and Impoverishment Effects of Out-of-pocket Expenses: A Comparative Study of Tannery and Non-tannery Workers of Kanpur, India

Science.gov (United States)

Kashyap, Gyan C.; Singh, Shri K.; Sharma, Santosh K.

2018-01-01

Purpose: Treatment-seeking behaviors and economic burden because of health expenditure are widely discussed issues in India, and more so in recent times. The aim of this study is to identify health problems of tannery workers and their treatment-seeking behavior and their health expenditure. Data and Methods: The primary data used in this article were collected through a cross-sectional household survey of 284 male tannery workers in the Jajmau area of Kanpur city in the state of Uttar Pradesh, during January–June 2015. Results: Findings of the study revealed that around 36% of the tannery workers and 42% of non-tannery workers received treatment as outpatients in government/municipal hospital in the first spell of treatment. The secondary source of treatment was pharmacy/drug stores for 30% of the tannery workers and 24% of the non-tannery workers, an indication that a substantial proportion takes treatment without consulting a qualified medical practitioner; it also highlights that almost one-third of the tannery and non-tannery workers visited private health facility despite poor economic condition. It is evident that a substantial proportion of tannery and non-tannery workers are visiting private/non-governmental organization/trust hospital despite their poor financial situation. Conclusion: There is an urgent need to reinstate people's faith in public health facilities by developing professionalism, integrity, and accountability among different levels of health functionaries and frontline workers with the support of credible, transparent, and responsible regulatory environment. PMID:29743781

Dynamics and driving forces of hides, skins, leather and leather ...

African Journals Online (AJOL)

Footwear and leather goods are constrained by lack of factories, competition from used goods, synthetic plastics and uninformed market. Investment in hides, skins and leather industry supported by training programmes has potential to generate great monetary revenue. Keywords: Hides, skin, leather, value chain, slaughter ...

Natural rubber: leather composites

Directory of Open Access Journals (Sweden)

K. Ravichandran

2005-06-01

Full Text Available Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have been discussed. Use of chrome leather particles has been found to improve the consumption of scrap rubber powder in natural rubber formulations. Polymer composites based on leather wastes as fillers are reported to be useful for many applications such as in construction materials, automobile interior moldings, heat and sound insulating boards, shoe soles, flooring materials and moldings with good anti-static properties, air permeability and good appearances.

Reversing the conventional leather processing sequence for cleaner leather production.

Science.gov (United States)

Saravanabhavan, Subramani; Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasami, Thirumalachari

2006-02-01

Conventional leather processing generally involves a combination of single and multistep processes that employs as well as expels various biological, inorganic, and organic materials. It involves nearly 14-15 steps and discharges a huge amount of pollutants. This is primarily due to the fact that conventional leather processing employs a "do-undo" process logic. In this study, the conventional leather processing steps have been reversed to overcome the problems associated with the conventional method. The charges of the skin matrix and of the chemicals and pH profiles of the process have been judiciously used for reversing the process steps. This reversed process eventually avoids several acidification and basification/neutralization steps used in conventional leather processing. The developed process has been validated through various analyses such as chromium content, shrinkage temperature, softness measurements, scanning electron microscopy, and physical testing of the leathers. Further, the performance of the leathers is shown to be on par with conventionally processed leathers through bulk property evaluation. The process enjoys a significant reduction in COD and TS by 53 and 79%, respectively. Water consumption and discharge is reduced by 65 and 64%, respectively. Also, the process benefits from significant reduction in chemicals, time, power, and cost compared to the conventional process.

Detection of hazardous pollutants in chrome-tanned leather using locally developed laser-induced breakdown spectrometer.

Science.gov (United States)

Nasr, M M; Gondal, Mohammed Asharf; Seddigi, Z S

2011-04-01

Highly toxic contaminants like Cr, As, and Pb were detected in chrome-tanning process of animal skin to produce leather by applying locally developed laser-induced breakdown spectrometer. An Nd-YAG laser with 1,064 nm wavelength was focused on the surface of leather samples (natural and manufactured) to generate a plasma spark and spectrally resolved spectra were used for identification and quantification of contaminants. The leather samples were collected from a tannery located in industrial cities of Riyadh and Jeddah, Saudi Arabia. The study was carried out on fully, half manufactured (wet blue leather), and natural hide (skin). To the best of our knowledge, this is the first attempt where laser-induced breakdown spectroscopy (LIBS) technique has been applied for the analysis of leather before and after tanning process. The maximum concentration of different elements of environmental significance like chromium, lead, arsenic, sulfur, magnesium were 199, 289, 31, 38, and 39 ppm, respectively, in one of the manufactured leather samples. The limit of detection (LOD) of our LIBS system for chromium, lead, arsenic, sulfur, and magnesium were 2, 3, 1.5,7, and 3 ppm, respectively. The safe permissible limit for tanned leather for highly toxic elements like chromium, lead, and arsenic are 1, 0.5, 0.01 ppm, respectively, as prescribed in Environmental Regulation Standards for Saudi Industries set by Royal Commission Jubail, Saudi Arabia. The LIBS technique is superior to other conventional techniques like ICP or atomic absorption that a little or no sample preparation is required, no chemicals are needed, multi-elemental analysis is possible for all kinds of samples (natural and anthropogenic materials), microgram of sample is essential, and LIBS could be applied for remote analysis. It is highly selective and sensitivity higher than ICP, and as no sample and chemicals are required, it is cost effective for multi-sample analysis per unit time as compared with other

Inventory of the chemicals and the exposure of the workers' skin to these at two leather factories in Indonesia

NARCIS (Netherlands)

Febriana, Sri Awalia; Jungbauer, Frank; Soebono, Hardyanto; Coenraads, Pieter-Jan

Tannery workers are exposed to hazardous chemicals. Tannery work is outsourced to newly industrialized countries (NICs) where attention into occupational health hazards is limited. In this study, we investigated the skin exposure to hazardous chemicals in tannery workers and determined the

Simultaneous removal of chromium and leather dye from simulated tannery effluent by photoelectrochemistry

International Nuclear Information System (INIS)

Monteiro Paschoal, Fabiana Maria; Anderson, Marc A.; Zanoni, Maria Valnice B.

2009-01-01

The feasibility of the photobleaching of a leather acid dye, acid red 151, simultaneously to degradation of anionic surfactant, Tamol, and reduction of Cr(VI) to the less toxic Cr(III) was investigated by photoelectrocatalytic oxidation. The best experimental conditions were found to be pH 2.0 and 0.1 mol L -1 sodium sulfate when the nanoporous Ti/TiO 2 photo anode was biased at +1.0 V and submitted to UV-irradiation. The photoelectrocatalytic oxidation promotes 100% discoloration, reducing around 98-100% of Cr(VI) and achieving an abatement of 95% of the original total organic carbon. The effect of pH, the applied potential, the Cr(VI) concentration and the complexation reaction between Cr(VI) and acid red dye were evaluated as to their effect on the kinetics of the reaction.

Research on Design Information Management System for Leather Goods

Science.gov (United States)

Lu, Lei; Peng, Wen-li

The idea of setting up a design information management system of leather goods was put forward to solve the problems existed in current information management of leather goods. Working principles of the design information management system for leather goods were analyzed in detail. Firstly, the acquiring approach of design information of leather goods was introduced. Secondly, the processing methods of design information were introduced. Thirdly, the management of design information in database was studied. Finally, the application of the system was discussed by taking the shoes products as an example.

Effect of cleaning products on upholstery leather finishes

OpenAIRE

Lara López, Mercedes

2003-01-01

The main objective of the project is to investigate the effects of cleaning products on upholstery leather finishes. Focusing on products applicable to upholstery leather cleaning, non-typical leather cleaners (and possible contaminants) or ink removers, in order to find out their behaviour, understanding how they work and if they are suitable for their purpose. Moreover an initial investigation about mechanism of soiling is proposed, in order, in the future, to avoid the soiling or develop a...

40 CFR 425.90 - Applicability; description of the retan-wet finish-splits subcategory.

Science.gov (United States)

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE... resulting from any tannery which processes previously unhaired and tanned splits into finished leather by...

Rhizofiltration of heavy metals from the tannery sludge by the ...

African Journals Online (AJOL)

The anchored hydrophyte, Hydrocotyle umbellata L., was employed for the removal of toxic metals from tannery sludge concentrations (w/v) from a tanneries wastewater treatment plant. Different concentrations of wet tannery sludge were prepared and plants of H. umbellata showed a good tolerance for all the prepared ...

Co-combustion of tannery sludge in a commercial circulating fluidized bed boiler.

Science.gov (United States)

Dong, Hao; Jiang, Xuguang; Lv, Guojun; Chi, Yong; Yan, Jianhua

2015-12-01

Co-combusting hazardous wastes in existing fluidized bed combustors is an alternative to hazardous waste treatment facilities, in shortage in China. Tannery sludge is a kind of hazardous waste, considered fit for co-combusting with coal in fluidized bedboilers. In this work, co-combustion tests of tannery sludge and bituminous coal were conducted in a power plant in Jiaxing, Zhejiang province. Before that, the combustion behavior of tannery sludge and bituminous were studied by thermogravimetric analysis. Tannery sludge presented higher reactivity than bituminous coal. During the co-combustion tests, the emissions of harmful gases were monitored. The results showed that the pollutant emissions met the Chinese standard except for NOx. The Concentrations of seven trace elements (As, Cr, Cd, Ni, Cu, Pb, Mn) in three exit ash flows (bottom ash in bed, fly ash in filter, and submicrometer aerosol in flue gas) were analyzed. The results of mono-combustion of bituminous coal were compared with those of co-combustion with tannery sludge. It was found that chromium enriched in fly ash. At last, the leachability of fly ash and bottom ash was analyzed. The results showed that most species were almost equal to or below the limits except for As in bottom ashes and Cr in the fly ash of co-combustion test. The concentrations of Cr in leachates of co-combustion ashes are markedly higher than that of coal mono-combustion ashes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Characterization and correlations of various pollution parameters in the tannery effluent

International Nuclear Information System (INIS)

Haydar, S.

2008-01-01

Wastewater characterization is an integral part of treatment and management strategies for industrial effluents. This paper outlines the results of detailed wastewater characterization studies conducted for a tannery in Sheikhupura, Punjab. The results of this study demonstrated that the composition of tannery wastewater could change continuously due to inherent nature of tannery operations. In general, tannery effluent was alkaline in nature and highly polluted in terms of organic, solids, sulfates, sulfides and chromium content. Basic ingredients of tannery effluent i.e. high alkalinity and substantial portions of BOD (Biochemical Oxygen Demand), COD (Chemical Oxygen Demand) and other pollutants in particulate form rendered it suitable for enhanced pollutant removals at primary stage of treatment using suitable coagulants. Results of primary treatment of wastewater from this tannery suggested that primary treatment alone was not capable of reducing pollutant loads significantly. Hence post-primary biological treatment was required to meet local effluent quality standards. (author)

Inventory of the chemicals and the exposure of the workers' skin to these at two leather factories in Indonesia.

Science.gov (United States)

Febriana, Sri Awalia; Jungbauer, Frank; Soebono, Hardyanto; Coenraads, Pieter-Jan

2012-07-01

Tannery workers are exposed to hazardous chemicals. Tannery work is outsourced to newly industrialized countries (NICs) where attention into occupational health hazards is limited. In this study, we investigated the skin exposure to hazardous chemicals in tannery workers and determined the prevalence of occupational skin diseases (OSDs) at tanneries in a NIC. A cross-sectional study on the observation of the working process and an inventory and risk assessment of the chemicals used. Classification of chemicals as potential sensitizers/irritants and a qualitative assessment of exposure to these chemicals. Workers were examined and interviewed using Nordic Occupational Skin Questionnaire-2002/LONG. The risk of OSDs at the investigated tanneries was mainly related to the exposure of the workers' skin to chemicals in hot and humid environmental conditions. In 472 workers, 12% reported a current OSD and 9% reported a history of OSD. In 10% of all cases, an OSD was confirmed by a dermatologist and 7.4% had an occupational contact dermatitis (OCD). We observed that personal protective equipment (PPE) used was mainly because of skin problems in the past and not as a primary protection against OSD. We observed a high frequency and prolonged exposure to many skin hazardous factors in tannery work although PPE was relatively easily available and which was generally used as a secondary preventative measure. The observed point-prevalence in this study was at the same level as that reported for other high-risk OSDs in Western countries and other tanneries in NICs. However, the observed point-prevalence in this study was lower than that reported in India and Korea. The results of our study and those of other studies at tanneries from other NICs were probably influenced by Healthy Worker Survivor Effect (HWSE).

Publications | Page 385 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Results 3841 - 3850 of 6384 ... Associations of fertility and pregnancy outcomes with leather tannery work in Mongolia : a pilot study (restricted access) ... West and Central African Research and Education Network (WACREN) Initiative : a change agent for improved connectivity and bandwidth in West and Central Africa ...

Pengujian Kemampuan Daya Samak Cube Black dan Limbah Cair Gambir Terhadap Mutu Kulit Tersamak

Directory of Open Access Journals (Sweden)

Gustri Yeni

2016-06-01

Full Text Available Leather tanning industries generally use sintetic tanner such as chrome (Cr+3 which can damage environment. Therefore, it is needed to find environmentally friendly tannery material, one is by using gambier. The aim of this research was to know tannic ability of gambier on goat’s leather and tuna fish. The gambier for tannery material contained high tannin (>70% namely Cube black and liquid waste from gambier processing. Concentration of tannery material that would be used for tanned was 1 kg. Tanned leather was tested to tannery degree (DP and physical test included pull strength, elongation, and rip strength, at same treatment compared to chrome tannery. Test results leather tanned showed that, the higher the concentration of tannery material the higher the results of DP, and the physical characteristic was better. Tanned leather from goat that used Cube black gambier concentration at 4% gave DP value approximately equal to chrome tanner (38,45% and 36,60%. For tanned tuna fish gave value of DP were 39,57% and 31,35%. Tannery material of gambier gave value of pull strength, rip strength, and elongation were higher than chrome’s. The value of pull strength of goat’s leather was 730,37 kg cm-2, tuna fish was 353,33 kg cm-2 got from liquid waste tanner. The value of rip strength fof goat’s leather was 353,33 kg cm-2, tuna fish skin 29,96 kg cm-2, and elongation value from tuna fish skin 202,0% was gotten from Cube black gambier. The result of the research showed that tannery material of gambier had tannery characteristic that can replace tanner of chrome.ABSTRAKIndustri penyamakan kulit umumnya menggunakan bahan penyamak sintetis seperti krom (Cr+3 yang dapat merusak lingkungan. Untuk itu, perlu dicari bahan penyamak yang ramah lingkungan, diantaranya menggunakan gambir. Tujuan penelitian ini adalah mengetahui daya samak gambir terhadap kulit kambing dan ikan tuna. Gambir untuk  bahan penyamak mengandung kadar tanin tinggi (>70% adalah

Experimental study on combustion and slagging characteristics of tannery sludge

International Nuclear Information System (INIS)

Li, Chunyu; Jiang, Xuguang; Fei, Zhenwei; Chi, Yong; Yan, Jianhua

2010-01-01

Incineration is the most reasonable technique for tannery sludge disposal. The combustion and gaseous products emission characteristics of tannery sludge were investigated in this study. Tendency of slagging for combustion residue was also investigated based on the composition and microscopic scanning analysis. The high content of volatile matters and ash in tannery sludge was discovered. It was shown that the thermal decomposition and combustion of tannery sludge mainly occurs in a temperature frame between 150 degree Celsius and 780 degree Celsius. Organic acid was determined as the most important gaseous pollutant at low temperature combustion. The combustion residue from a specially designed furnace was analyzed by X-ray diffractometer (XRD) and energy dispersion spectroscopy (EDS) microprobe coupled in a scanning electron micro-scope (SEM). There is large amount of Ca in the combustion residue, and CaO was the main inorganic composition in these residues. The tannery sludge studied in this paper has a strong tendency of slagging, and the fusion of the residue began at 900 degree Celsius in combustion. It was further discovered that almost all the zinc (Zn) in tannery sludge is volatilized at 900 degree Celsius. The degree of volatilization for heavy metals at 900 degree Celsius followed the order of Zn > Cd >Cu > Mn > Pb > Cr. Most of Cr in tannery sludge is enriched in the residue during combustion. The present study reveals that it is critical to control the combustion temperature for optimal combustion efficiency and minimization of pollutants emission. (author)

Energy Efficiency Upgrades for the Clinic and the Tannery and Wind Energy for Power to the Tannery

Energy Technology Data Exchange (ETDEWEB)

Kakoona, Jane [Native Village of Shishmaref, AK (United States); Fredenberg, Connie [Native Village of Shishmaref, AK (United States)

2017-05-08

Under this grant agreement, the Native Village of Shishmaref (Shishmaref) will complete weatherization retrofits to two community buildings, the Clinic and the Tannery, based on recent energy audits. Located 5 miles from the mainland, 126 miles north of Nome and 100 miles south of Kotzebue, Shishmaref sits on Sarichef Island in the Chukchi Sea. As such, Shishmaref experiences a transitional climate between the frozen Arctic and the continental Interior. Summers can be foggy, with average temperatures ranging from 47 to 54 °F (Fahrenheit); winter temperatures average -12 to 2 °F. With heating fuel costs of almost $7/gallon, the goal of this project is to reduce energy costs at the Clinic and the Tannery by at least 30 to 50% through energy efficiency and weatherization measures and through the installation of a residential-size wind turbine to supplement power for the Tannery building.

The Degredation and Conservation of Leather

Directory of Open Access Journals (Sweden)

Vicki Dirksen

1997-11-01

Full Text Available This paper examines the tanning processes used in the manufacture of leather and the implications such processes have on the deterioration of aging leather. Improving the understanding of the processes used to create leather should result in a museum professional who is better able to address the conservation and care of leather artefacts. Present methods of leather conservation are examined with regard to the advantages and disadvantages of each method.

LEGISLATIVE ASPECTS CONCERNING THE LEATHER WASTES

Directory of Open Access Journals (Sweden)

TIMOFTE Claudia Simona

2017-05-01

Full Text Available This paper underlines the current legislation and compliance issues leather waste in different waste groups according to relevant legislation and shows that, although seemingly harmless waste of skin sometimes contain dangerous compounds. As presented risks to human health were some restricted substances in leather. Since 2001 Romania had preoccupation in national legislation on waste management, but some categories, such as leather waste are not framed to this category. Also, another goal is implementing the EU management/storage strategy of industrial waste. Unfortunately, Romania imports huge quantities of used clothing and shoes. Transport, storage and use of them are poor, and many of these are subsequently stored waste by the fact that it is even sometimes improperly discarded. The paper also shows the statistics on waste management in the Bihor County by activity of national economy and by activity of industry at level of CANE REV.2 Section. Analyzing the postings on Internet regarding the sale and purchase of leather wastes in Romania, it was found that there are the following 'categories' of wastes: leather goods, leather from coats, leather from footwear industry, suede, leather, leather resulting from the production of upholstery. It was found that most car buyers use waste leather upholstery. It is recommended that production companies to highlight more transparent their inventory textile and leather waste on types for those interested (including online can access/capitalize them.

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids.

Science.gov (United States)

Krishnamoorthy, G; Sadulla, S; Sehgal, P K; Mandal, Asit Baran

2012-05-15

In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T(s)) and denaturation temperature (T(d)) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T(s) of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning. Copyright © 2012 Elsevier B.V. All rights reserved.

Pemanfaatan kembali air limbah terolah dengan sistem wetland untuk pembuatan kulit glace

Directory of Open Access Journals (Sweden)

Sri Sutyasmi

2014-06-01

Full Text Available Tanneries use large quantities of water and produce high pollutant load. Wastewater recycling is an effective way to conserve water supplies. The purpose of this study was to reuse wastewater that has been treated with a wetland system to save water and to apply cleaner production in tannery industry. The treated wastewater was tested in accordance with the test requirements of water used for leather tanning process. The treated wastewater test results met the requirements of SNI 06-0649-1989 Water for the tanning process. Furthermore, treated wastewater was used for leather tanning process with variations of wastewater used were 0, 25, 50, 75 and 100%. The resulting leather was tested in accordance with SNI 06-0253-1989 Quality requirement of goat glace leather. The test results met the SNI. Utilization of 75 % wastewater gave the best result.

Electrochemical treatment of tannery wastewater using DSA electrodes

International Nuclear Information System (INIS)

Costa, Carla Regina; Botta, Clarice M.R.; Espindola, Evaldo L.G.; Olivi, Paulo

2008-01-01

In this work we studied the electrochemical treatment of a tannery wastewater using dimensionally stable anodes (DSA) containing tin, iridium, ruthenium, and titanium. The electrodes were prepared by thermal decomposition of the polymeric precursors. The electrolyses were performed under galvanostatic conditions, at room temperature. Effects of the oxide composition, current density, and effluent conductivity were investigated, and the current efficiency was calculated as a function of the time for the performed electrolyses. Results showed that all the studied electrodes led to a decrease in the content of both total phenolic compounds and total organic carbon (TOC), as well as lower absorbance in the UV-vis region. Toxicity tests using Daphnia similis demonstrated that the electrochemical treatment reduced the wastewater toxicity. The use of DSA type electrodes in the electrochemical treatment of tannery wastewater proved to be useful since it can promote a decrease in total phenolic compounds, TOC, absorbance, and toxicity

Electrochemical treatment of tannery wastewater using DSA electrodes

Energy Technology Data Exchange (ETDEWEB)

Costa, Carla Regina [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, CEP 14049-901 Ribeirao Preto, SP (Brazil); Botta, Clarice M.R.; Espindola, Evaldo L.G. [Nucleo de Estudos em Ecossistemas Aquaticos, Centro de Recursos Hidricos e Ecologia Aplicada, Escola de Engenharia de Sao Carlos, Universidade de Sao Paulo, CP 292, CEP 13560-970 Sao Carlos, SP (Brazil); Olivi, Paulo [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, CEP 14049-901 Ribeirao Preto, SP (Brazil)], E-mail: olivip@ffclrp.usp.br

2008-05-01

In this work we studied the electrochemical treatment of a tannery wastewater using dimensionally stable anodes (DSA) containing tin, iridium, ruthenium, and titanium. The electrodes were prepared by thermal decomposition of the polymeric precursors. The electrolyses were performed under galvanostatic conditions, at room temperature. Effects of the oxide composition, current density, and effluent conductivity were investigated, and the current efficiency was calculated as a function of the time for the performed electrolyses. Results showed that all the studied electrodes led to a decrease in the content of both total phenolic compounds and total organic carbon (TOC), as well as lower absorbance in the UV-vis region. Toxicity tests using Daphnia similis demonstrated that the electrochemical treatment reduced the wastewater toxicity. The use of DSA type electrodes in the electrochemical treatment of tannery wastewater proved to be useful since it can promote a decrease in total phenolic compounds, TOC, absorbance, and toxicity.

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids

International Nuclear Information System (INIS)

Krishnamoorthy, G.; Sadulla, S.; Sehgal, P.K.; Mandal, Asit Baran

2012-01-01

Highlights: ► Unnatural D-AA assisted tanned leathers found soft and full possessing tight grain. ► Increased hydrothermal stability of collagen via intra and inter molecular crosslink. ► D-Ly+Ald tanned leathers revealed a properly oriented with well aligned structure. ► D-AA in collagen creates new topologies inaccessible to homo chiral molecules. ► Improves conventional tanning process, and reduce the total solid and liquid wastes. - Abstract: In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T s ) and denaturation temperature (T d ) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T s of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning.

LEATHER WASTE VALORISATION THROUGH MATERIAL INNOVATION: SOME PROPERTIES OF LEATHER WOOD FIBREBOARD

Directory of Open Access Journals (Sweden)

Axel M. RINDLER

2015-12-01

Full Text Available Due to the ever-increasing scarcity of resources and raw materials in the wood panels industry, it is imperative to look for suitable alternatives to the established resources. Therefore a combination of the traditionally used and newly explored sources may reveal highly innovative ways. The objective of this study is to provide an insight into the behavior of the material and possible new applications of those fiber/particle wood and waste leather composites. For this reason exclusively fibers of spruce were used for the trials. Wet white (WW leather particles and wet blue (WB leather particles were mixed with the wooden materials for the production of high density fibreboards. Besides the mechanical properties such as the internal bond (IB the bending strength (MOR and modulus of elasticity (MOE was analyzed. Further physical property as thickness swelling after 24h watering was investigated. To analyze how the density influences the behavior under thermal conditions, fiberboards with the densities 500, 700 and 900 kg/m³ were tested. The results of the material properties were influenced by the leather content of the panels. The results for the UF-bonded HDF boards show enhancement of the transverse IB with increasing wet blue leather content, whereas the other mechanical properties decline meanwhile. The thickness swelling showed higher values compared to the wood fibreboard. The results of this study underline the usefulness of integrating leather shavings to HDF and give an overview of their influence in wood fiber materials. The combination of the natural resource wood fiber and the leather waste products (Wet Blue and Wet White gives a very interesting new material, its mechanical properties allow a variety of possible application in future applications.

Natural leathers from natural materials: progressing toward a new arena in leather processing.

Science.gov (United States)

Saravanabhavan, Subramani; Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasami, Thirumalachari

2004-02-01

Globally, the leather industry is currently undergoing radical transformation due to pollution and discharge legislations. Thus, the leather industry is pressurized to look for cleaner options for processing the raw hides and skins. Conventional methods of pre-tanning, tanning and post-tanning processes are known to contribute more than 98% of the total pollution load from the leather processing. The conventional method of the tanning process involves the "do-undo" principle. Furthermore, the conventional methods employed in leather processing subject the skin/ hide to a wide variation in pH (2.8-13.0). This results in the emission of huge amounts of pollution loads such as BOD, COD, TDS, TS, sulfates, chlorides and chromium. In the approach illustrated here, the hair and flesh removal as well as fiber opening have been achieved using biocatalysts at pH 8.0, pickle-free natural tanning employing vegetable tannins, and post-tanning using environmentally friendly chemicals. Hence, this process involves dehairing, fiber opening, and pickle-free natural tanning followed by ecofriendly post-tanning. It has been found that the extent of hair removal and opening up of fiber bundles is comparable to that of conventionally processed leathers. This has been substantiated through scanning electron microscopic analysis and softness measurements. Performance of the leathers is shown to be on par with conventionally chrome-tanned leathers through physical and hand evaluation. The process also exhibits zero metal (chromium) discharge and significant reduction in BOD, COD, TDS, and TS loads by 83, 69, 96, and 96%, respectively. Furthermore, the developed process seems to be economically viable.

Green chemistry approaches to leather tanning process for making chrome-free leather by unnatural amino acids

Energy Technology Data Exchange (ETDEWEB)

Krishnamoorthy, G.; Sadulla, S.; Sehgal, P.K. [Central Leather Research Institute, Council of Scientific and Industrial Research (CSIR), Adyar, Chennai 600 020 (India); Mandal, Asit Baran, E-mail: abmandal@hotmail.com [Central Leather Research Institute, Council of Scientific and Industrial Research (CSIR), Adyar, Chennai 600 020 (India)

2012-05-15

Highlights: Black-Right-Pointing-Pointer Unnatural D-AA assisted tanned leathers found soft and full possessing tight grain. Black-Right-Pointing-Pointer Increased hydrothermal stability of collagen via intra and inter molecular crosslink. Black-Right-Pointing-Pointer D-Ly+Ald tanned leathers revealed a properly oriented with well aligned structure. Black-Right-Pointing-Pointer D-AA in collagen creates new topologies inaccessible to homo chiral molecules. Black-Right-Pointing-Pointer Improves conventional tanning process, and reduce the total solid and liquid wastes. - Abstract: In the present study, green and sustainable method or eco-friendly approaches to tanning process based on unnatural D-amino acids (D-AA)-aldehyde (Ald) as a substitute for chrome-free tanning has been attempted. The distribution of optically active D-AA in tanned leather, the hydrothermal stability, the mechanical properties and resistance to collagenolytic activity of tanned leather, the evaluation of eco-friendly characteristics were investigated. Scanning electron microscopic (SEM) and Atomic force microscopic (AFM) analyses indicate the surface morphology and roughness, respectively, of the tanned leather collagen matrix. Shrinkage and Differential scanning calorimetric (DSC) analyses shows that the shrinkage temperature (T{sub s}) and denaturation temperature (T{sub d}) of tanned leather are related to the content of D-AA+Ald present in the leather matrix. It has been found that the T{sub s} of D-AA tanned leather is more than that of Ald tanned leather and also more or less equal to chrome tanned leather. Environmental impact assessment (EIA) shows that the developed process results in significant reduction in total solids content (TSC) and improves better biodegradability of organic compound present in the effluent compared to chrome tanning.

Patulin in apple leather in Iran.

Science.gov (United States)

Montaseri, H; Eskandari, M H; Yeganeh, A T; Karami, S; Javidnia, K; Dehghanzadeh, G R; Mesbahi, G R; Niakousari, M

2014-01-01

Apple leather is made by dehydration of cooked fruit into leathery sheets. Mould growth and patulin production can occur in damaged apples or when fallen fruit is collected for apple leather processing. A survey was conducted to determine levels and dietary intake of patulin from apple leather marketed in Iran. Patulin was detected in all samples at concentrations ranging from leather.

Toxicity of leather tanning wastewater effluents in sea urchin early development and in marine microalgae.

Science.gov (United States)

Meriç, Süreyya; De Nicola, Elena; Iaccarino, Mario; Gallo, Marialuisa; Di Gennaro, Annamaria; Morrone, Gaetano; Warnau, Michel; Belgiorno, Vincenzo; Pagano, Giovanni

2005-10-01

This study was designed to investigate the composition and the toxicity of leather tanning wastewater and conditioned sludge collected at the leather tanning wastewater treatment plant (CODISO) located in Solofra, Avellino (Southern Italy). Samples were analyzed for their conventional parameters (COD, TSS, chromium and ammonia) and for metal content. Effluent samples included raw wastewater, and samples collected following coagulation/flocculation process and biological treatment. A set of toxicity endpoints were tested using sea urchin and marine microalgal bioassays by evaluating acute embryotoxicity, developmental defects, changes in sperm fertilization success and transmissible damage from sperm to the offspring, and changes in algal growth rate. Dose-related toxicity to sea urchin embryogenesis and sperm fertilization success was exerted by effluent or sludge samples according to the following rank: conditioned sludge > coagulated effluent > or = raw influent > effluent from biological treatment. Offspring quality was not affected by sperm exposure to any wastewater or to sludge samples. Algal growth was inhibited by raw or coagulated effluent to a similar extent and, again, the effluent from the biological treatment resulted in a decreased toxicity. The results suggest that coagulated effluent and conditioned sludge result in higher toxicity than raw influent in sea urchin embryos and sperm, whereas the biological wastewater treatment of coagulated effluent, in both sea urchins and algae, cause a substantial improvement of wastewater quality. Hence a final biological wastewater treatment should be operated to minimize any environmental damage from tannery wastewater.

Fruit Leathers: Method of Preparation and Effect of Different Conditions on Qualities

Directory of Open Access Journals (Sweden)

Lemuel M. Diamante

2014-01-01

Full Text Available Fruit leathers are dehydrated fruit products which are eaten as snacks or desserts. They are flexible sheets that have a concentrated fruit flavor and nutritional aspects. Most fruit leathers are prepared by mixing fruit puree and other additives like sugar, pectin, acid, glucose syrup, color, and potassium metabisulphite and then dehydrating them under specific conditions. Various drying systems including combined convective and far-infrared drying, hot air drying, microwave drying, solar drying, and sun drying have been used to make fruit leathers. Most fruit leathers are dried at 30 to 80°C for up to 24 hours until the target final moisture content (12–20% has been reached. Research about fruit leathers began in the 1970s. This work has reviewed published papers on fruit leathers in order to summarize useful information about fruit leathers on methods of preparation, effects of drying condition, and effects of packaging and storage, which will be useful to many in the food industry and consumers who are health-conscious.

Fruit Leathers: Method of Preparation and Effect of Different Conditions on Qualities

Science.gov (United States)

Diamante, Lemuel M.; Bai, Xue; Busch, Janette

2014-01-01

Fruit leathers are dehydrated fruit products which are eaten as snacks or desserts. They are flexible sheets that have a concentrated fruit flavor and nutritional aspects. Most fruit leathers are prepared by mixing fruit puree and other additives like sugar, pectin, acid, glucose syrup, color, and potassium metabisulphite and then dehydrating them under specific conditions. Various drying systems including combined convective and far-infrared drying, hot air drying, microwave drying, solar drying, and sun drying have been used to make fruit leathers. Most fruit leathers are dried at 30 to 80°C for up to 24 hours until the target final moisture content (12–20%) has been reached. Research about fruit leathers began in the 1970s. This work has reviewed published papers on fruit leathers in order to summarize useful information about fruit leathers on methods of preparation, effects of drying condition, and effects of packaging and storage, which will be useful to many in the food industry and consumers who are health-conscious. PMID:26904618

Natural Leathers from Natural Materials:  Progressing toward a New Arena in Leather Processing

OpenAIRE

Saravanabhavan, Subramani; Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasami, Thirumalachari

2004-01-01

Globally, the leather industry is currently undergoing radical transformation due to pollution and discharge legislations. Thus, the leather industry is pressurized to look for cleaner options for processing the raw hides and skins. Conventional methods of pre-tanning, tanning and post-tanning processes are known to contribute more than 98% of the total pollution load from the leather processing. The conventional method of the tanning process involves the “do−undo” pri...

Multicriteria cost–benefit assessment of tannery production: The need for breakthrough process alternatives beyond conventional technology optimization

Energy Technology Data Exchange (ETDEWEB)

Giannetti, Biagio F. [Paulista University (UNIP) (Brazil); Agostinho, Feni, E-mail: feni@unip.br [Paulista University (UNIP) (Brazil); Moraes, Luciano C.; Almeida, Cecília M.V.B. [Paulista University (UNIP) (Brazil); Ulgiati, Sergio, E-mail: sergio.ulgiati@uniparthenope.it [Università degli studi di Napoli, Parthenope (Italy)

2015-09-15

The worldwide use of chromium-based processes in tanneries generates increased concerns about their related environmental burdens. Cleaner production alternatives for leather production are being proposed, based on the optimization of specific aspects or criteria, for instance, reducing demand for specific materials and energy, or reducing local toxicological emissions. While improvement on individual characteristics of the process is certainly to be favored, a more comprehensive evaluation of alternatives is also needed to prevent the risk of shifting the burden to increase global load while addressing one specific critical factor of production. This work aims to discuss the importance of a multicriteria, multiscale approach to address cleaner production strategy costs and benefits. For this, materials balance, an economic approach, and emergy (with an “m”) accounting methods are applied to selected unhairing/liming, pickling/tanning and wastewater treatment steps in a tannery process, which was chosen as a case study. Results show that the assessed recycling cleaner production strategies assessed allow the manufacturer to reduce by one half the amount of water used and the demand for chemicals up to 4% with respect to the business-as-usual process, at the expense of increasing electricity demand by 10%. Economic cost-to-benefit ratio was 25$ benefits per 1$ invested, as well as an emergy-based cost-to-benefit of 33Em$ per 1Em$ invested, of course these improvements were limited to the three investigated process steps. The improvement in cost/benefit ratios indicates that converting scenario #0 into #1 is favorable under economic and emergy views. However, when the two scenarios are investigated from the point of view of the imbalance in local and renewable resource use versus imported and nonrenewable use, the emergy method shows a small overall increase in renewability (from 3.51% to 3.85%), a low, but expected, emergy yield ratio equal to 1, and a high

Multicriteria cost–benefit assessment of tannery production: The need for breakthrough process alternatives beyond conventional technology optimization

International Nuclear Information System (INIS)

Giannetti, Biagio F.; Agostinho, Feni; Moraes, Luciano C.; Almeida, Cecília M.V.B.; Ulgiati, Sergio

2015-01-01

The worldwide use of chromium-based processes in tanneries generates increased concerns about their related environmental burdens. Cleaner production alternatives for leather production are being proposed, based on the optimization of specific aspects or criteria, for instance, reducing demand for specific materials and energy, or reducing local toxicological emissions. While improvement on individual characteristics of the process is certainly to be favored, a more comprehensive evaluation of alternatives is also needed to prevent the risk of shifting the burden to increase global load while addressing one specific critical factor of production. This work aims to discuss the importance of a multicriteria, multiscale approach to address cleaner production strategy costs and benefits. For this, materials balance, an economic approach, and emergy (with an “m”) accounting methods are applied to selected unhairing/liming, pickling/tanning and wastewater treatment steps in a tannery process, which was chosen as a case study. Results show that the assessed recycling cleaner production strategies assessed allow the manufacturer to reduce by one half the amount of water used and the demand for chemicals up to 4% with respect to the business-as-usual process, at the expense of increasing electricity demand by 10%. Economic cost-to-benefit ratio was 25$ benefits per 1$ invested, as well as an emergy-based cost-to-benefit of 33Em$ per 1Em$ invested, of course these improvements were limited to the three investigated process steps. The improvement in cost/benefit ratios indicates that converting scenario #0 into #1 is favorable under economic and emergy views. However, when the two scenarios are investigated from the point of view of the imbalance in local and renewable resource use versus imported and nonrenewable use, the emergy method shows a small overall increase in renewability (from 3.51% to 3.85%), a low, but expected, emergy yield ratio equal to 1, and a high

All projects related to | Page 677 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

2006-03-02

Mongolia has a large number of small leather tanneries that process some 30 000 skins per day, for a total output of about 8 million units per year. Start Date: March 2, 2006. End Date: April 1, 2009. Topic: TANNERIES, TANNING INDUSTRY, CHEMICAL POLLUTION, TOXIC METALS, CADMIUM, OCCUPATIONAL HEALTH, ...

Characterization of tannery sludge from the leather industry of Franca industrial district, SP, Brazil; Caracterizacao de um lodo de cromo proveniente da industria de couro do distrito industrial de Franca

Energy Technology Data Exchange (ETDEWEB)

Chambi, M.M.; Toffoli, S.M., E-mail: marvinchp@usp.br [Universidade de Sao Paulo (USP), SP (Brazil). Escola Politecnica. Departamento de Engenharia Metalurgica

2011-07-01

The industry of leather manufacture generates large quantities of solid leather waste with characteristics of high-polluting and hazardous conditions. Among these wastes, stands out the wet blue leather (chromed leather scraps), and the tanning sludge and secondary sludge generated in the processes of effluents treatment. These wastes contain Cr(III), which, under oxidizing conditions, can turn into Cr (VI), which is highly toxic. However, these wastes are a potential source of chromium oxide (traditional industrial pigment), which could be used by the glass and ceramic enamel industries. In this study, a preliminary characterization of a chromium sludge from the industrial district of Franca-SP was conducted. X-ray diffraction (XRD), chemical (XRF) and thermal (DTA / TG) analyses were used to determine the physical and chemical characteristics of this solid waste. The potential of using this material as an available and cheap pigment for the manufacture of enamels and glass is discussed. (author)

Thermal valorization of footwear leather wastes in bubbling fluidized bed combustion.

Science.gov (United States)

Bahillo, A; Armesto, L; Cabanillas, A; Otero, J

2004-01-01

Transformation of hide (animal skins) into leather is a complicated process during which significant amounts of wastes are generated. Footwear is the sector that consumes the major part of leather (60%). Logically, this industry is producing the largest quantity of leather wastes. The objective of this work was to demonstrate the technical feasibility of fluidized bed technology to recover the energy from burning footwear leather wastes. Considering the characteristics of leather waste, especially the heating value (12.5-21 MJ/kg), it can be considered a fairly good fuel. Moreover, leather waste has suitable characteristics for combustion, e.g., high volatile matter (76.5%) and low ash content (5.2%). Two factors deserve special attention: N3O and NOx emissions as a consequence of its unusual high nitrogen content (14.1%) and the chromium speciation because chromium is the main element of ash (3.2%) due to its use in leather tanning. A series of experiments has been carried out in a 0.1 MWt bubbling fluidized bed pilot plant. The combustion efficiency, flue gas composition and chromium speciation were investigated. Despite having high nitrogen content, a low conversion rate of fuel-N to NOx and N2O was attained. Chromium was concentrated in the solid streams and it was consistently found as Cr(III+); no presence of Cr(VI+) was detected.

MANAGEMENT OF PROCESSING AND RECOVERY OF LEATHER WASTE

Directory of Open Access Journals (Sweden)

STAN Ovidiu Valentin

2014-05-01

Full Text Available The leather and leather goods industry development is conditioned by the development of the supply of raw materials - animal husbandry and chemical industries, sectors that tend to develop intensive on vertical - which causes a shortage of raw materials in relation with the market demand for quality products. The leather is the basic raw material of the leather and leather goods industry, this raw material is the most substantial contribution to downstream sectors, giving them a competitive advantage and it is known that the leather has the greatest potential to add value to the products in which it is incorporated. The advantages of using leather are many, the most important qualities are its hygienic properties, flexibility and adaptability to a wide variety of applications. Leather is manufactured on demand for each type of application, such as shoes, clothes, gloves, handbags, furniture upholstery or car interiors, yachts and planes. It requires better use of raw materials by using new technologies and manufacturing processes based on non-invasive methods on the environment leading to increase the product life cycle. The leather and leather goods industry is a supplier of large amounts of waste from the production cycle, waste that has the same properties and qualities as raw material used in the base product. Leather waste represents a loss for the companies, an additional cost related to storage and environmental protection.

The role of organic load and ammonia inhibition in anaerobic digestion of tannery fleshing

Directory of Open Access Journals (Sweden)

Cecilia Polizzi

2018-06-01

Full Text Available In this study, batch tests on anaerobic digestion of tannery fleshing (skin-residue waste from hides’ tanning process, as sole substrate, have been performed with the purpose of assessing the effects of high substrate concentration and consequent ammonia inhibition on the process. Co-digestion with tannery primary sludge was also evaluated. According to the results, no inhibition occurred at initial organic load up to 5 gVS/l; an inhibited steady state was observed at 10 gVS/l, and system failure and instability was showed at the highest load of 20 gVS/l. Co-digestion with tannery primary sludge proved feasible, probably due to dilution effect. The observed ammonia and VFA accumulation over the experimental time-lapse is also discussed. Results are intended to increase knowledge on the technological application of anaerobic digestion of sole tannery fleshing, in the perspective of its application as on-site treatment solution for decentralised tanneries. Keywords: Anaerobic digestion, Tannery waste, Ammonia inhibition, Organic load

Assessment of exposure to chemical agents and ergonomic stressors in tanneries in Kanpur, India.

Science.gov (United States)

Ory, F G; Rahman, F U; Katagade, V; Shukla, A; Burdorf, A

1997-10-01

In developing countries qualitative assessment of exposure at the workplace may be an essential tool in evaluating hazardous working conditions. This survey reports on qualitative assessment of exposure to chemicals, dust, and ergonomic stressors among 298 workers in 15 tanneries in Kanpur, India. In general, chemical exposure and dermal exposure were highest among beamhouse workers, less for workers involved in dry finishing activities, and lowest for those performing the wet finishing of hides. Dermal exposure was rated as high to very high during beamhouse activities, reflecting direct contact with wet hides and manual handling of hides in soak tanks. Relevant dust exposure was observed only during dry finishing activities. Most workers experienced severe postural load due to working in trunk flexion and rotation for more than 50% of their daily work time. In addition, manual materials handling with loads over 20 kg frequently occurred. The size of the tannery, in general a reflection of state of technology, showed no systematic influence on exposure profiles. The survey suggested that mechanization of material transfer and application of trolleys reduced the work time with trunk flexion and rotation and implied less manual lifting. The presence of local exhaust ventilation in large tanneries seemed to reduce the chemical exposure. This survey has demonstrated the importance of rapid appraisal techniques for evaluating hazardous conditions at the workplace. In developing countries this approach may facilitate occupational hygiene research and practice.

Impregnation of leather during "freeze-drying"

DEFF Research Database (Denmark)

Storch, Mikkel; Vestergaard Poulsen Sommer, Dorte; Hovmand, Ida

2016-01-01

Freeze-drying is a recognized method for the preservation of waterlogged objects. Naturally, freeze-drying has also been used for waterlogged archaeological leather often after treatment with Na2.EDTA and impregnation with PEG; but the treated leather sometimes suffers from “excessive drying......” becoming too stiff and brittle. The aim of this study was to examine the effect of a conventional freeze-drying method against an alternative freeze-drying method that preserves the natural moisture content of the leather. Both new and archaeological waterlogged leather were included in the study...... suggest that the process which takes place within the leather during the freeze-drying in not actual freeze-drying, but rather a sophisticated way of distributing the impregnating agent. The pure ice phase freezes out, but the impregnating agent remains liquid as the temperature does not become low enough...

Comparisons of micrometeorology, growth of leather-fern [Rumohra adiantiformis, pteridophyta] and comfortable working environment between PO-film-covered and net-covered greenhouses in summer

International Nuclear Information System (INIS)

Yokoyama, H.; Harazono, Y.

2004-01-01

Protected cultivation of leather-fern in Hachijo-Island has been urged to prevent the Mottled Yellowing Syndrome (MYS) damage and to reduce the production costs. The purpose of the study was to reveal greenhouse environments that would provide good plant growth, a comfortable working environment and low-cost management, by comparing the micrometeorology and leatherfern productivity between Poly-Olefin (PO) film-covered greenhouses and the conventional netcovered greenhouses. Both greenhouses were fully covered by the same net. Field studies of leather-fern cultivation in Hachijo-Island showed that better productivity and quality of leather-fern have been provided by farmer's net-covered greenhouses than by farmer's PO-covered greenhouses. The light transmittance in the net-covered greenhouse was higher and the air temperature was lower than those in the PO-covered greenhouse. The comparative experiments using PO-covered greenhouses (PO), and net-covered greenhouses (NET), were conducted at the Hachijojima Horticultural Research Center. Air temperature and its vertical gradient in NET were lower than those in PO. Irrigation in PO was 225 mm during August and September in 1999, but 507 mm of precipitation in addition to the irrigation was supplied in NET. Air temperature and its vertical gradient in PO increased with solar radiation increase. Heat disorder in working environments for farmers did not occur in the NET, but several warning hours of heat disorder occurred in the PO as a dangerous working environment. The NET was thought to be a better system of leather-fern cultivation bringing about low costs and comfortable working environments. However, further application of fully rolled-up PO-film greenhouse system was recommended to control the soil water condition

ETHIOPIA

African Journals Online (AJOL)

Preferred Customer

tanneries in the world (about 90%) use chromium salts to produce leather, because these salts provide better leather ... former are not biodegradable. .... Each sample was filtered with Whatman filter paper (0.45 μm of pore size). .... might be causing pollution of the surrounding air with hydrogen sulfide, which also warrants.

Biosorption and biotransformation of chromium by Serratia sp. isolated from tannery effluent.

Science.gov (United States)

Srivastava, Shaili; Thakur, Indu Shekhar

2012-01-01

A bacterium isolated from soil and sediment ofa leather tanning mill's effluent was identified as Serratia sp. by the analysis of 16S rDNA. Scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDX) and transmission electron microscopy (TEM) were used to assess morphological changes and confirm chromium biosorption in Serratia sp. both in a shake-flask culture containing chromium and in a tannery wastewater. The SEMEDX and the elemental analysis of the chromate-containing samples confirmed the binding of chromium with the bacterial biomass. The TEM exhibited chromium accumulation throughout the bacterial cell, with some granular deposits in the cell periphery and in the cytoplasm. X-ray diffraction analysis (XRD) was used to quantify the chromium and to determine the chemical nature of the metal-microbe interaction. The XRD data showed the crystalline character of the precipitates, which consisted of mainly calcium chromium oxide, chromium fluoride phosphate and related organo-Cr(III) complex crystals. The XRD data also revealed a strong involvement of cellular carboxyl and phosphate groups in chromium binding by the bacterial biomass. The results of the study indicated that a combined mechanism of ion-exchange, complexation, croprecipitation and immobilization was involved in the biosorption of chromium by bacterial cells in contaminated environments.

Chrome-tanned leather shavings as a filler of butadiene-acrylonitrile rubber.

Science.gov (United States)

Przepiórkowska, A; Chrońska, K; Zaborski, M

2007-03-06

The noxious wastes from the tanning industry such as chrome-tanned leather shavings were used as the only filler of rubber mixes containing carboxylated butadiene-acrylonitrile rubber (XNBR) or butadiene-acrylonitrile rubber (NBR), and a dispersing agent Limanol PEV (Schill & Seilacher). The best form addition of leather powder to the rubber mixes is mixed the waste protein with zinc oxide. The leather powder added to the rubber mixes improves the mechanical properties: tensile strength (T(s)), elongation at break (epsilon(b)) and increase the cross-linking density of carboxylated XNBR and NBR rubber mixes. Satisfactory results of these studies are presented in this work.

Leather quality of some Sudan desert sheep and goats

Directory of Open Access Journals (Sweden)

Mohammed Alhadi Ebrahiem

2016-04-01

Full Text Available This trial is aimed to study leather properties that produced from Sudan Desert sheep and goats in relation to breed type and age category. Thirty pieces of fresh sheep and goats skins were collected randomly (15 for each during January 2015. The collected skins were tanned and the produced leather properties were studied. The Statistix 8 program for variance analysis was used for data analysis. The study samples were taken according to the Complete Randomized Design. Sheep leather results revealed that, lamb's skin was significantly (P ≥ 0.05 produced better quality leather than ram's and ewe's skins in elongation (%, tensile strength (kg/cm2, cracking load (kg, thickness (mm, tear load (kg/cm, flexibility and moisture%. While it was yielded leather with the same characteristics to ram's and ewe's leather in Ash (%, fat (% and chrome (%. Leather properties [elongation (%, tensile strength (kg/cm2, cracking load (kg, tear load (kg/cm, flexibility and Ash (%] were significantly (P ≥ 0.05 affected by breed variation. On the other hand thickness (mm, moisture (%, fat (% and chrome (% were not significantly (P ≥ 0.05 affected by breed. Ram's skin was produced better quality leather than ewe's skins. Goat's leather results revealed that, kid goat's skin was significantly (P ≥ 0.05 produced better quality leather than bucks and doe's skin in tensile strength (kg/cm2, cracking load (kg, thickness (mm, tear load (kg/cm and flexibility degree. But kids and buck's skins were produced the same quality leather in elongation % and moisture% with significant variation (P ≥ 0.05 to doe's leather. Kid's skin yields leather with the same characteristics to buck's and doe's leather in Ash (%, fat (% and chrome (%. Generally Desert goats produce slightly better quality leather than Nubian goats. Leather prosperities [cracking load (kg, tear load (kg/cm, and Ash (%] were significantly (P ≥ 0.05 affected by breed variation. Elongation (%, tensile

Modified silica sol coatings for surface enhancement of leather.

Science.gov (United States)

Mahltig, Boris; Vossebein, Lutz; Ehrmann, Andrea; Cheval, Nicolas; Fahmi, Amir

2012-06-01

The presented study reports on differently modified silica sols for coating applications on leather. Silica sols are prepared by acidic hydrolysis of tetraethoxysilane and modified by silane compounds with fluorinated and non-fluorinated alkylgroups. In contrast to many earlier investigations regarding sol-gel applications on leather, no acrylic resin is used together with the silica sols when applying on leather. The modified silica particles are supposed to aggregate after application, forming thus a modified silica coating on the leather substrate. Scanning electron microscopy investigation shows that the applied silica coatings do not fill up or close the pores of the leather substrate. However, even if the pores of the leather are not sealed by this sol-gel coating, an improvement of the water repellent and oil repellent properties of the leather substrates are observed. These improved properties of leather by application of modified silica sols can provide the opportunity to develop sol-gel products for leather materials present in daily life.

Biosorption of hexavalent chromium in a tannery industry wastewater using fungi species

International Nuclear Information System (INIS)

Sivakumar, D.

2016-01-01

The isolated fungi species of different kinds from chromium contaminated soil sites located in Nagalkeni, Chennai were used for reducing chromium(VI) in a tannery industry wastewater of Nagalkeni, Chennai. The experiments were conducted to know biosorption potential of isolated fungi species for removing chromium(VI) in a tannery industry wastewater against the different p H, fungi biomass and chromium(VI) concentration (dilution ratio). The results of this study indicated that the order of maximum removal of chromium(VI) by an isolated fungi species at an optimum pH of 3, fungi biomass of 4g and an initial chromium(VI) concentration of 18.125 mg/L (dilution ratio 4) is A. niger > A. flavus > A. fumigatus > A. nidulans > A. heteromorphus > A. foetidus > A. viridinutans. This study found that the maximum removal of chromium(VI) was achieved by Aspergillus niger (96.3 %) than other fungi species at chromium(VI) concentration of 18.125 mg/L in a tannery industry wastewater. The chromium removal from tannery industry wastewater was validated by checking chromium removal in an aqueous solution and by checking the removal efficiency of other parameters in a tannery industry wastewater using same isolated A. niger. Biosorption model was proposed to simulate the experimental condition for removing chromium(VI) in a tannery industry wastewater by all isolated fungi species. The R2 and x2 values of the proposed model predicted that the proposed biosorption model is very much useful for predicting the trend of reduction potential of chromium(VI) in a tannery industry wastewater by all isolated fungi species. This study suggested that one could select the type of fungi species, ion concentration level, selection of treatment period, quantity of biomass to be used, and p H level of the medium, to achieve the highest reduction of any toxic metals from any contaminated water, wastewater and soil environment.

Short-term dermal exposure to tannery effluent does not cause behavioral changes in male Swiss mice

Directory of Open Access Journals (Sweden)

Bruna de Oliveira Mendes

2018-02-01

Full Text Available Tannery is a highly polluting activity due to the waste generated by bovine skin processing. Although there are several studies highlighting the health issues faced by workers exposed to tannery effluent, there are no records of experiments testing the neurobehavioral effects resulting from direct contact with this pollutant. Thus, the aim of the current study is to assess the possible neurobehavioral effects of dermal exposure to tannery effluent on male Swiss mice. Animals were divided in three groups, which were subjected to the same experimental time period and conditions: effluent group - animals in direct contact with tannery effluent (for 20 days; control group - animals in contact with pure water; and dry-control group - animals not exposed to water or to tannery effluent. Neurobehavioral tests started on the 17th experimental day. Results of the elevated plus-maze test (anxiety prediction showed no anxiogenic or anxiolytic effects, memory deficit or depressive symptoms on animals exposed to tannery effluent. Thus, the current results do not support the hypothesis that male Swiss mice dermal exposure to tannery effluents for the same time period and experimental conditions leads to neurobehavioral changes. Therefore, the herein adopted exposure protocol was not good to study the effects of dermal exposure to tannery effluent on the chosen experimental model.

Supplementation of inorganic phosphate enhancing the removal efficiency of tannery sludge-borne Cr through bioleaching.

Science.gov (United States)

Zheng, Guanyu; Zhou, Lixiang

2011-10-15

Four inorganic mineral nutrients including NH4+, K+, Mg2+ and soluble inorganic phosphate (Pi) were investigated to reveal the potential limiting nutrients for tannery sludge bioleaching process driven by Acidithiobacillus species, and the feasibility of supplementing the limiting nutrients to accelerate tannery sludge bioleaching was studied in the present study. It was found that the concentration of Pi was lower than 3.5 mg/L throughout the whole bioleaching process, which is the most probable restricting nutrient for tannery sludge bioleaching. Further experiments revealed that the deficiency of Pi could seriously influence the growth of Acidithiobacillus thiooxidans and lower its oxidization capacity for S0, and the limiting concentration of Pi for the growth of A. thiooxidans was 6 mg/L. The low concentration of soluble Pi in sludge matrix was resulted from the extremely strong sorbing/binding capacity of tannery sludge for phosphate. The supplementation of more than 1.6 g/L KH2PO4 into tannery sludge bioleaching system could effectively stimulate the growth of Acidithiobacillus species, enhance Cr removal rate and further shorten tannery sludge bioleaching period from 10 days to 7 days. Therefore, inorganic phosphate supplementation is an effective and feasible method to accelerate tannery sludge bioleaching process, and the optimum dosage of KH2PO4 was 1.6 g/L for tannery sludge with 5.1% of total solids. Copyright © 2011 Elsevier Ltd. All rights reserved.

Recovery of Proteins and Chromium Complexes from Chromium – Containing Leather Waste (CCLW

Directory of Open Access Journals (Sweden)

B. Gutti

2010-08-01

Full Text Available Chromium – Containing Leather Waste (CCLW constitutes an environmental pollution problem to leather industries disposing the waste by landfill. The waste mainly consists of collagen and chromium III complexes. This work is a design of reactors to recover gelatin, polypeptides and chromium from CCLW. The results of the experiment shows that 68% of protein, based on dry weight of leather scraps, could be recovered. Three reactors with a total volume of 18 m3 was designed to handle 10,431 kg of waste generated from the tanning industries.

Studies on the use of power ultrasound in leather dyeing.

Science.gov (United States)

Sivakumar, Venkatasubramanian; Rao, Paruchuri Gangadhar

2003-03-01

Uses of power ultrasound for acceleration/performing the chemical as well as physical processes are gaining importance. In conventional leather processing, the diffusion of chemicals through the pores of the skin/hide is achieved by the mechanical agitation caused by the paddle or drumming action. In this work, the use of power ultrasound in the dyeing of leather has been studied with the aim to improve the exhaustion of dye for a given processing time, to reduce the dyeing time and to improve the quality of dyed leather. The effect of power ultrasound in the dyeing of full chrome cow crust leather in a stationary condition is compared with dyeing in the absence of ultrasound as a control experiment both in a stationary as well as conventional drumming condition. An ultrasonic cleaner (150 W and 33 kHz) was used for the experiments. Actual power dissipated into the system was calculated from the calorimetric measurement. Experiments were carried out with variation in type of dye, amount of dye offer, temperature and time. The results show that there is a significant improvement in the percentage exhaustion of dye due to the presence of ultrasound, when compared to dyeing in absence of ultrasound. Experiments on equilibrium dye uptake carried out with or without ultrasound suggest that ultrasound help to improve the kinetics of leather dyeing. The results indicate that leathers dyed in presence of ultrasound have higher colour values, better dye penetration and fastness properties compared to control leathers. The physical testing results show that strength properties of the dyed leathers are not affected due to the application of ultrasound under the given process conditions. Apparent diffusion coefficient during the initial stage of dyeing process, both in presence and in absence of ultrasound was calculated. The values show that ultrasound helps in improving the apparent diffusion coefficient more for the difficult dyeing conditions such as in the case of metal

POTENTIAL USE OF COLLAGEN HYDROLYSATES FROM CHAMOIS LEATHER WASTE AS INGREDIENT IN LEATHER FINISHING FORMULATIONS

Directory of Open Access Journals (Sweden)

POPA Emil

2016-05-01

Full Text Available The aim of this paper is the obtaining of value-added products from the dust resulted from chamois leather buffering, a solid waste that raises serious disposal problems, due to its physical state and complex chemical composition. Starting from leather waste, an alkaline hydrolysis was performed followed by the chemical modification of the polypeptyde hydrolysate by polycondensation with dispersions of copolymers of vinyl acetate with acrylic esters and reticulation with glutaraldehyde in order to improve its hydrophobicity. The resulted product can be used/was tested as an ingredient in leather finishing formulations, as binder or carrier agent. In this paper, new finishing mixtures were prepared using pigments and obtained polypeptide hydrolysates as a substitute for casein in pigment pastes. By this method, there were obtained two experimental variants of brown and black pigment pastes which were compared to the pigment pastes with casein binder. Natural grain Box bovine leather samples coated with such admixtures were subjected to physico-mechanical resistance tests, in accordance with the standardized methods. Specific tests carried on finished leather – tensile strength, tear resistance, resistance to grain cracking, dry and wet rubbing fastness, flexural fatigue strength test, etc – showed values of this characteristics comparable to those obtained with casein conventional finishing.

Laser vibrometry in the quality control of the break of tanned leather

Science.gov (United States)

Preciado, J. Sanchez; Lopez, C. Perez; Hernandez-Montes, M. del Socorro; Torre-Ibarra, M. de la; Moreno, J. M. Flores; Ruiz, C. Tavera; Mendoza Santoyo, F.; Galan, M.

2018-05-01

Tanning industry treats hides and the skin of animals for their use in products such as clothes, furniture and car's interiors. The worth of leather is highly affected by defects that may appear prior or during the tanning process. Break, which refers to the wrinkling of the grain surface of leather, is one of the main issues because it affects not only the visual appearance of leather, but also its mechanical properties. The standardized method to classify the break pattern is done by bending the leather with the hand and comparing visually the resulting wrinkles that appear with a reference pattern, which makes the classification subjective and limits the evaluation to small areas. Laser vibrometry is an optical technique that has been applied in vibrational and modal analysis, which are methodologies used to obtain the mechanical properties of materials. This work demonstrates the use of a single-point vibrometer as a noncontact and nondestructive optical method to discriminate among five break levels, which could increase the effectiveness of leather classification for quality control in the tanning industry.

Color pollution control in textile dyeing industry effluents using tannery sludge

Directory of Open Access Journals (Sweden)

Sajjala Sreedhar Reddy

2008-12-01

Full Text Available Effective treatment of dyestuff containing textile dyeing industry effluents require advanced treatment technologies such as adsorption for the removal of dyestuffs. Powdered commercial coal based activated carbon has been the most widely used adsorbent for the removal of dyestuffs from dyeing industry effluents. As an alternative to commercial coal based activated carbon, activated carbon prepared from dried tannery sludge was used as an adsorbent for dyestuff removal from simulated textile dying industry effluent in this study. The color removal performance of tannery sludge derived activated carbon and commercial coal based activated carbon has been investigated using parameters such as adsorbent dosage, initial dye concentration, pH and temperature. It was found that tannery sludge derived activated carbon exhibits dye removal efficiency that is about 80–90 % of that observed with commercial coal based activated carbon. The amount of dye adsorbed on to tannery sludge derived activated carbon is lower compared with commercial activated carbon at equilibrium and dye adsorption capacity increased with increase of initial dye concentration and temperature, and deceasing pH. It was found that the Langmuir isotherm appears to fit the isotherm data better than the Freundlich isotherm. The leachate of heavy metals from tannery sludge derived activated carbon to the environment is very low, which are within the standard limit of industrial effluent and leachable substances.

Ultrasonic effects on titanium tanning of leather.

Science.gov (United States)

Peng, Biyu; Shi, Bi; Sun, Danhong; Chen, Yaowen; Shelly, Dennis C

2007-03-01

The effects of ultrasound on titanium tanning of leather were investigated. Either 20 or 40 kHz ultrasound was applied to the titanium tanning of pigskins. Five different treatment conditions were carried out and the effects were examined, such as leather shrinkage temperature (T(s)), titanium content and titanium distribution in the leather. Overall heat loading was carefully controlled. Results showed that 20 kHz ultrasound effectively improves titanium agent penetration into the hide and increases the leather's shrinkage temperature. Doubling the frequency to 40 kHz produced negligible enhancements. An impressive 105.6 degrees C T(s) was achieved using 20 kHz ultrasound pretreatment of the tanning liquor followed by 20 kHz ultrasound in the tanning mixture (liquor plus pigskins) in a special salt-free medium. Finally, using a unique ultrasonic tanning drum with 26.5 kHz ultrasound, the T(s) reached a record level of 106.5 degrees C, a value not achieved in conventional (no ultrasound) titanium tanning. The ultrasonic effects on titanium tanning of leather are judged to make a superior mineral tanned leather.

Improvement of technical purpose materials performance characteristics with the radio frequency low pressure plasma

Science.gov (United States)

Makhotkina, L. Yu; Khristoliubova, V. I.

2017-11-01

The main aim of the work is to solve the actual problem of increasing the competitiveness of tanning products by reducing the prime cost and improving the quality of finished products due to the increased durability of the working elements of tanneries. The impact of the low pressure radio frequency (RF) plasma in the processes of treating for modification of the materials for special purposes is considered in the article. The results of working elements of tanneries and the materials for special purposes sample processing by a RF low pressure plasma are described. As a result of leather materials nano structuring and nano modifying physical, mechanical and hygienic characteristics were increased. Processing of the technical purpose materials allows to increase operational performance of products and extend their lifespan.

Manufacturing Of Novelty Leather From Cattle Stomach

Directory of Open Access Journals (Sweden)

Umme Habiba Bodrun Naher

2015-08-01

Full Text Available Abstract The objective of this study was to investigate the feasibility of turning cattle stomach into novelty leather and then leather product which would add value to end of cattle. Four pieces of green buffalo stomachs were taken through soaking liming deliming pickling tanning neutralization retanning dyeing and fat liquoring operation. Then mechanical operations like drying and staking operations were also done. Some physical tensile strength stitch tear strength and colour rub fastness and chemical chromic oxide content fat content and pH tests were accomplished .The results of physical tests were poor compared to the grain leather as the composition of raw outer coverings of animals and their stomachs are different. The stomach leathers could be used for making coin purse key case bracelet wrist watch belt ear-ring necklace hair band iPod case etc. as novelty leather product item.

Tannin fingerprinting in vegetable tanned leather by solid state NMR spectroscopy and comparison with leathers tanned by other processes.

Science.gov (United States)

Romer, Frederik H; Underwood, Andrew P; Senekal, Nadine D; Bonnet, Susan L; Duer, Melinda J; Reid, David G; van der Westhuizen, Jan H

2011-01-28

Solid state ¹³C-NMR spectra of pure tannin powders from four different sources--mimosa, quebracho, chestnut and tara--are readily distinguishable from each other, both in pure commercial powder form, and in leather which they have been used to tan. Groups of signals indicative of the source, and type (condensed vs. hydrolyzable) of tannin used in the manufacture are well resolved in the spectra of the finished leathers. These fingerprints are compared with those arising from leathers tanned with other common tanning agents. Paramagnetic chromium (III) tanning causes widespread but selective disappearance of signals from the spectrum of leather collagen, including resonances from acidic aspartyl and glutamyl residues, likely bound to Cr (III) structures. Aluminium (III) and glutaraldehyde tanning both cause considerable leather collagen signal sharpening suggesting some increase in molecular structural ordering. The ²⁷Al-NMR signal from the former material is consistent with an octahedral coordination by oxygen ligands. Solid state NMR thus provides easily recognisable reagent specific spectral fingerprints of the products of vegetable and some other common tanning processes. Because spectra are related to molecular properties, NMR is potentially a powerful tool in leather process enhancement and quality or provenance assurance.

Radiation grafting processes and properties of leathers modified with butyl acrylate

International Nuclear Information System (INIS)

Pietrucha, K.

1982-01-01

Conditions for radiation induced grafting with butyl acrylate dispersed in water emulsion onto chrome-tanned pig skins have been worked out for γ-rays and electron beam irradiations. The highest yield of grafting was observed at monomer concentration approximately 25% (w/w), dose equal to 25 kGy and dose rate not exceeding 10 MGy/h. At these conditions the yield of grafting attained a value approximately 25% and content of homopolymer in the leather amounted to 6%. The efficiency of monomer to polymer conversion decreases when the concentration of monomer in emulsion and dose rate increases. Yield of homopolymer is independent of the dose rate. An explanation of the observed relations has been proposed. The physical and used properties of grafted leathers were tested. Radiation processed leathers were found superior to samples finished by traditional methods. One has to point to better tolerance against chemical cleaning and reduced water take-up without loss of high permeability of water vapour, responsible for good hygienic properties of leather products. Recommendations for industrial scale radiation grafting are given. (author)

Vitrification as an alternative to landfilling of tannery sewage sludge

International Nuclear Information System (INIS)

Celary, Piotr; Sobik-Szołtysek, Jolanta

2014-01-01

Highlights: • The possibility of vitrification of tannery sewage sludge was investigated. • Glass cullet was substituted with different wastes of mineral character. • Component ratio in the processed mixtures was optimized. • Environmental safety of the acquired vitrificates was verified. • An alternative management approach of usually landfilled waste was presented. - Abstract: Due to high content of heavy metals such as chromium, tannery sewage sludge is a material which is difficult to be biologically treated as it is in the case of organic waste. Consequently, a common practice in managing tannery sewage sludge is landfilling. This poses a potential threat to both soil and water environments and it additionally generates costs of construction of landfills that meet specific environment protection requirements. Vitrification of this kind of sewage sludge with the addition of mineral wastes can represent an alternative to landfilling. The aim of this study was to investigate the possibility of obtaining an environmentally safe product by means of vitrification of tannery sewage sludge from a flotation wastewater treatment process and chemical precipitation in order to address the upcoming issue of dealing with sewage sludge from the tannery industry which will be prohibited to be landfilled in Poland after 2016. The focus was set on determining mixtures of tannery sewage sludge with additives which would result in the lowest possible heavy metal leaching levels and highest hardness rating of the products obtained from their vitrification. The plasma vitrification process was carried out for mixtures with various amounts of additives depending on the type of sewage sludge used. Only the materials of waste character were used as additives. One finding of the study was an optimum content of mineral additives in vitrified mixture of 30% v/v waste molding sands with 20% v/v carbonate flotation waste from the zinc and lead industry for the formulations with

Vitrification as an alternative to landfilling of tannery sewage sludge

Energy Technology Data Exchange (ETDEWEB)

Celary, Piotr, E-mail: pcelary@is.pcz.czest.pl; Sobik-Szołtysek, Jolanta, E-mail: jszoltysek@is.pcz.czest.pl

2014-12-15

Highlights: • The possibility of vitrification of tannery sewage sludge was investigated. • Glass cullet was substituted with different wastes of mineral character. • Component ratio in the processed mixtures was optimized. • Environmental safety of the acquired vitrificates was verified. • An alternative management approach of usually landfilled waste was presented. - Abstract: Due to high content of heavy metals such as chromium, tannery sewage sludge is a material which is difficult to be biologically treated as it is in the case of organic waste. Consequently, a common practice in managing tannery sewage sludge is landfilling. This poses a potential threat to both soil and water environments and it additionally generates costs of construction of landfills that meet specific environment protection requirements. Vitrification of this kind of sewage sludge with the addition of mineral wastes can represent an alternative to landfilling. The aim of this study was to investigate the possibility of obtaining an environmentally safe product by means of vitrification of tannery sewage sludge from a flotation wastewater treatment process and chemical precipitation in order to address the upcoming issue of dealing with sewage sludge from the tannery industry which will be prohibited to be landfilled in Poland after 2016. The focus was set on determining mixtures of tannery sewage sludge with additives which would result in the lowest possible heavy metal leaching levels and highest hardness rating of the products obtained from their vitrification. The plasma vitrification process was carried out for mixtures with various amounts of additives depending on the type of sewage sludge used. Only the materials of waste character were used as additives. One finding of the study was an optimum content of mineral additives in vitrified mixture of 30% v/v waste molding sands with 20% v/v carbonate flotation waste from the zinc and lead industry for the formulations with

Tannin Fingerprinting in Vegetable Tanned Leather by Solid State NMR Spectroscopy and Comparison with Leathers Tanned by Other Processes

Directory of Open Access Journals (Sweden)

Jan H. van der Westhuizen

2011-01-01

Full Text Available Solid state 13C-NMR spectra of pure tannin powders from four different sources – mimosa, quebracho, chestnut and tara – are readily distinguishable from each other, both in pure commercial powder form, and in leather which they have been used to tan.  Groups of signals indicative of the source, and type (condensed vs. hydrolyzable of tannin used in the manufacture are well resolved in the spectra of the finished leathers.  These fingerprints are compared with those arising from leathers tanned with other common tanning agents.  Paramagnetic chromium (III tanning causes widespread but selective disappearance of signals from the spectrum of leather collagen, including resonances from acidic aspartyl and glutamyl residues, likely bound to Cr (III structures. Aluminium (III and glutaraldehyde tanning both cause considerable leather collagen signal sharpening suggesting some increase in molecular structural ordering. The 27Al-NMR signal from the former material is consistent with an octahedral coordination by oxygen ligands. Solid state NMR thus provides easily recognisable reagent specific spectral fingerprints of the products of vegetable and some other common tanning processes. Because spectra are related to molecular properties, NMR is potentially a powerful tool in leather process enhancement and quality or provenance assurance.

Recycling of Chrome Tanned Leather Dust in Acrylonitrile Butadiene Rubber

Science.gov (United States)

El-Sabbagh, Salwa H.; Mohamed, Ola A.

2010-06-01

Concerns on environmental waste problem caused by chrome tanned leather wastes in huge amount have caused an increasing interest in developing this wastes in many composite formation. This leather dust was used as filler in acrylonitrile butadiene rubber (NBR) before treatment and after treatment with ammonia solution and sod. formate. Different formulations of NBR/ leather dust (untreated-treated with ammonia solution—treated with sod. formate) composites are prepared. The formed composite exhibit a considerable improvement in some of their properties such as rheometric characteristics especially with composites loaded with treated leather dust. Tensile strength, modulus at 100% elongation, hardness and youngs modulus were improved then by further loading start to be steady or decrease. Cross linking density in toluene were increased by incorporation of leather dust treated or untreated resulting in decreases in equilibrium swelling. Distinct increase in the ageing coefficient of both treated and untreated leather with drop in NBR vulcanizates without leather dust. Addition of leather dust treated or untreated exhibit better thermal stability.

Occupational health and the environment in an urban slum in India.

Science.gov (United States)

Shukla, A; Kumar, S; Ory, F G

1991-01-01

The Indo-Dutch Environmental & Sanitary Engineering Project under the Ganga action Plan in Kanpur and Mirzapur is being executed within the Indo-Dutch bilateral development cooperation framework. The project aims to integrate physical, social and health related improvements. It is expected that the development approach and methodology can be replicated in other urban settlements in India. The project is being supplemented by a training and institutional strengthening programme to facilitate the transfer of new technologies and improvement of operation and maintenance of the new facilities. The project is also aimed at the improvement of the living conditions of the population, by installing drinking water and drainage systems. A socio-economic unit in the project supports the technical interventions by enhancing the community to participate in project activities. The Occupational Health Programme in Jajmau, an industrial slum of Kanpur, aims to improve the working conditions of tannery workers. Four hundred and ninety-seven tannery workers and 80 employees not engaged in leather work, from 20 tanneries, were interviewed and underwent physical examination. The mean age of tannery workers was 32 years, about half of them recently migrated to Kanpur. The majority of the workers are illiterate, have temporary jobs and 85% have a monthly income between 300 and 600 Rs. Occupational morbidity was 28.2%. Regular meetings with tannery owners, the training of tannery workers in first aid, and support for the installation of safety and health councils in tanneries are the main programme activities.(ABSTRACT TRUNCATED AT 250 WORDS)

40 CFR 425.40 - Applicability; description of the retan-wet finish-sides subcategory.

Science.gov (United States)

2010-07-01

... PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS LEATHER TANNING AND FINISHING POINT SOURCE... resulting from any tannery which processes previously tanned hides and skins (grain side only) into finished...

Physicochemical and Bacteriological Assessment of Tannery ...

African Journals Online (AJOL)

ADOWIE PERE

dissolved solids, total hardness, magnesium, sodium, potassium, iron, manganese, nitrite, ... treatment of tannery effluents before discharge into the environment is necessary using ... humans, animal s and plants. ... beam house is where the preparatory processes for ... water bodies of dissolved oxygen (Rajiv et al., 2012).

All projects related to | Page 662 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

... Governance, Health, Information and Communication, Natural Resources, Gender ... Risk Assessment from Leather Tanneries in Ulaanbaatar (Mongolia) ... Program: Food, Environment, and Health ... Topic: MANGANESE, HEALTH SURVEYS, HEALTH HAZARDS, ENVIRONMENTAL MONITORING, ENVIRONMENTAL ...

Tannin Fingerprinting in Vegetable Tanned Leather by Solid State NMR Spectroscopy and Comparison with Leathers Tanned by Other Processes

OpenAIRE

Jan H. van der Westhuizen; David G. Reid; Melinda J. Duer; Susan L. Bonnet; Frederik H. Romer; Andrew P. Underwood; Nadine D. Senekal

2011-01-01

Solid state 13C-NMR spectra of pure tannin powders from four different sources – mimosa, quebracho, chestnut and tara – are readily distinguishable from each other, both in pure commercial powder form, and in leather which they have been used to tan.  Groups of signals indicative of the source, and type (condensed vs. hydrolyzable) of tannin used in the manufacture are well resolved in the spectra of the finished leathers.  These fingerprints are compared with those arising from leathers tann...

Stabilization of chromium: an alternative to make safe leathers.

Science.gov (United States)

Gong, Ying; Liu, Xiaoling; Huang, Li; Chen, Wuyong

2010-07-15

In this study, the original causes for hexavalent chromium presence in the leather were first evaluated by ageing of chromium(III) solutions and chrome tanned hide powder (50 degrees C, UV lightening at 340 nm, 0-36 h). The results showed that the trivalent chromium at instable coordination state was easy to convert into hexavalent chromium in high pH environment, and the probability of the oxidation increased in this order: multi-coordinate chromium, mono-coordinate chromium, and free chromium. For this reason, the process for stabilizing chromium in the leather was designed with the specific material, which was mostly consisted of the reducers and the chelating agents. After treated with the developed process, these leathers were aged (50 degrees C, UV irradiance as 0.68 W/m(2) at 340 nm, 0-72 h) to estimate chromium(VI) presence. Hexavalent chromium was not found in these treated leathers even if the leathers were aged for 72 h. Moreover, the physical and mechanical properties for the leathers varied little after treating. In a word, an inherent safe and effective process was proved to avoid the formation of hexavalent chromium in the leather. 2010 Elsevier B.V. All rights reserved.

Incorporation feasibility of leather residues in bricks

Energy Technology Data Exchange (ETDEWEB)

Aguiar, J.B. [Minho Univ. (Portugal). Civil Engineering Dept.; Valente, A.; Pires, M.J. [Inst. of Development and Innovation Technology of Minho, Braga (Portugal); Tavares, T. [Biological Engineering Dept., Univ. of Minho, Braga (Portugal)

2002-07-01

The footwear industry has strips of leather as one of its by-products. These leather residues, due to their high chromium content, can be regarded as a threat to the environment, particularly if no care is taken with their disposal. With the incorporation of the residues in ceramic products, after trituration, is possible to neutralise the eventual toxicity of chromium. In a laboratory study we produced prismatic bricks using clay from the region and incorporating 1, 3 and 5% (by mass) of leather residues. This corresponds at about 20, 60 and 100% (by apparent volume). The moulds were filled up with paste and, in order to have some compactness, the ceramic paste was compressed with a spatula. After that, it began the process of drying and burning the bricks. They were tested to flexure, compression and leaching. The results showed that the toxicity of chromium disappeared in the bricks. The mechanical tests showed a decrease in strength for the specimens with leather residue. The compressive strength decreases about 22% for 1% of incorporation of leather residue. However, as bricks were lighter and more porous, we can expect that they are better for thermal isolation. (orig.)

Kinetic coefficients for the biological treatment of tannery wastewater

International Nuclear Information System (INIS)

Haydar, S.

2008-01-01

Determination of kinetic coefficients for a particular wastewater is imperative for the rational design of biological treatment-facilities. The present study was undertaken with the objective of finding out kinetic coefficients for tannery wastewater. A bench-scale model of aerated lagoon, consisting of an aeration tank and final clarifier, was use to conduct the studies. The model was operated continuously for 96 days, by varying the detention times from 3 to 9 days. Influent for the aerated lagoon was settled tannery wastewater. Biochemical oxygen demand (BOD) of the influent and effluent and the mixed-liquor suspended solids (MLSS) of aeration tank were determined at various detention-times so as to generate data for kinetic coefficients. The kinetic coefficients k, Ks, Y and Ed were found to be 3.125 day/sup -1/, 488 mg/L, 0.64 and 0.035 day/sup -1/ respectively. Overall rate-constant of BOD, removal 'K' was also determined and was found to be 1.43 day/sup -1/. Kinetic coefficients were determined, at mean reactor-temperature of 30.2 degree C. These coefficients may be utilized for the design of biological-treatment facilities for tannery wastewater. (author)

IMPACT OF LEATHER PROCESSING INDUSTRIES ON CHROMIUM CONCENTRATION IN GROUNDWATER SOUTH OF CHENNAI CITY, INDIA

Science.gov (United States)

Elango, L.; Brindha, K.; G. Rajesh, V.

2009-12-01

The groundwater quality is under threat due to disposal of effluents from a number of industries. Poor practice of treatment of wastes from tanning industries or leather processing industries lead to pollution of groundwater. This study was carried out with the objective of assessing the impact of tanneries on groundwater quality in Chromepet area which is a part of the metropolitan area of Chennai, Tamil Nadu, India. This area serves as the home town for a number of small and large scale tanning industries. People in certain parts of this area depend on the groundwater for their domestic needs as there is no piped drinking water supply system. Topographically this region is generally flat with gentle slope towards east and north east. The charnockite rocks occur as basement at the depth of about 15m from the surface of this area. Weathered charnockite rock occurs at the depth from 7m to 15m from the ground surface. The upper layer consists of loamy soil. Groundwater occurs in the unconfined condition at a depth from 0.5m to 5m. Thirty six groundwater samples were collected during March 2008 and the groundwater samples were analysed for their heavy metal (chromium) content using atomic absorption spectrophotometer. Bureau of Indian Standards (BIS) recommended the maximum permissible limit of chromium in drinking water as 0.05 mg/l. Considering this, it was found that 86% of the groundwater samples possessed concentration of chromium above the maximum permissible limit recommended by BIS. The tanneries use chrome sulphate to strengthen the leather and make it water repellent. The excess of chromium gets washed off and remains in the wastewater. This wastewater is disposed into open uncovered drains either untreated or after partial treatment. Thus the chromium leaches through the soil and reaches the groundwater table. Apart from this, there is also huge quantity of solid waste resulting from the hides and skins which are dumped off without suitable treatment. The

Vitrification as an alternative to landfilling of tannery sewage sludge.

Science.gov (United States)

Celary, Piotr; Sobik-Szołtysek, Jolanta

2014-12-01

Due to high content of heavy metals such as chromium, tannery sewage sludge is a material which is difficult to be biologically treated as it is in the case of organic waste. Consequently, a common practice in managing tannery sewage sludge is landfilling. This poses a potential threat to both soil and water environments and it additionally generates costs of construction of landfills that meet specific environment protection requirements. Vitrification of this kind of sewage sludge with the addition of mineral wastes can represent an alternative to landfilling. The aim of this study was to investigate the possibility of obtaining an environmentally safe product by means of vitrification of tannery sewage sludge from a flotation wastewater treatment process and chemical precipitation in order to address the upcoming issue of dealing with sewage sludge from the tannery industry which will be prohibited to be landfilled in Poland after 2016. The focus was set on determining mixtures of tannery sewage sludge with additives which would result in the lowest possible heavy metal leaching levels and highest hardness rating of the products obtained from their vitrification. The plasma vitrification process was carried out for mixtures with various amounts of additives depending on the type of sewage sludge used. Only the materials of waste character were used as additives. One finding of the study was an optimum content of mineral additives in vitrified mixture of 30% v/v waste molding sands with 20% v/v carbonate flotation waste from the zinc and lead industry for the formulations with flotation sewage sludge, and 45% v/v and 5% v/v, respectively, for precipitation sewage sludge. These combinations allowed for obtaining products with negligible heavy metal leaching levels and hardness similar to commercial glass, which suggests they could be potentially used as construction aggregate substitutes. Incineration of sewage sludge before the vitrification process lead to

The status and developments of leather solid waste treatment: A mini-review.

Science.gov (United States)

Jiang, Huiyan; Liu, Junsheng; Han, Wei

2016-05-01

Leather making is one of the most widespread industries in the world. The production of leather goods generates different types of solid wastes and wastewater. These wastes will pollute the environment and threat the health of human beings if they are not well treated. Consequently, the treatment of pollution caused by the wastes from leather tanning is really important. In comparison with the disposal of leather wastewater, the treatment of leather solid wastes is more intractable. Hence, the treatment of leather solid wastes needs more innovations. To keep up with the rapid development of the modern leather industry, various innovative techniques have been newly developed. In this mini-review article, the major achievements in the treatment of leather solid wastes are highlighted. Emphasis will be placed on the treatment of chromium-tanned solid wastes; some new approaches are also discussed. We hope that this mini-review can provide some valuable information to promote the broad understanding and effective treatment of leather solid wastes in the leather industry. © The Author(s) 2016.

Modification of natural leather by grafting emulsion copolymerization technique

International Nuclear Information System (INIS)

Badran, A.S.; Nasr, H.E.; El-Halawany, N.R.; Mohamed, W.S.

2005-01-01

Grafting emulsion copolymerization of methyl methacrylate (MMA) with butyl acrylate of different molar ratios onto natural leather with different molar ratios was carried out using developed redox initiation system of potassium persulphate (PPS) as an oxidizing agent and some sodium bisulphite adducts as reducing agent, as well as sodium dodecyl sulphate (SDS) was used as an anionic emulsifier. The grafted leather was characterized via FTIR, SEM and thermal gravimetric analysis. Moreover, the grafted leather was evaluated through water absorption, tensile strength, dyeing performance and hardness measurements. The obtained results revealed that the physical and mechanical properties of the modified leather were enhanced

Thermal and enzymatic recovering of proteins from untanned leather waste.

Science.gov (United States)

Bajza, Z; Vrucek, V

2001-01-01

The laboratory trials of a process to treat untanned leather waste to isolate valuable protein products are presented. In this comparative study, both thermal and enzymatic treatments of leather waste were performed. The enzymatic method utilizes commercially available alkaline protease at moderate temperatures and for short periods of time. The concentration of the enzyme was 500 units per gram of leather waste which makes the method cost-effective. Amino acid composition in the hydrolysate obtained by the enzyme hydrolysis of untanned leather waste is determined. Chemical and physical properties of protein powder products from untanned leather waste were evaluated by spectrophotometric and chromatographic methods and by use of electron microscope. The results of microbiological assays confirm that these products agree to food safety standards. This relatively simple treatment of untanned leather waste may provide a practical and economical solution to the disposal of potentially dangerous waste.

Remedial measures for improving the quality of raw stock for leather processing

International Nuclear Information System (INIS)

Khan, M.S.; Ahmed, N.; Hasny, S.I.

2007-01-01

Leather is an important international commodity of commerce. It plays a vital the country. The raw stock, namely cow, buffalo, goat and sheep skins, are important sources for producing varieties of leather articles, such as shoe uppers, leather garments, bag leather articles, such as, shoe uppers, leather garments, bag leather, sole leather, gloves, belts, upholstery. The quality of raw stock is good in Pakistan but it is damaged due to mishandling during slaughtering and in the later stages, which is actually a heavy economic loss. The main complaint of the tanning industry is that locally available hides are full of butcher cuts. They also leave too much fleshy tissues. The flesh can be removed later, but the cuts, particularly the deep cuts because of holes as a result of improper flaying are irrepairable and permanent. A number of pre and post-mortem defects (during animal life and after slaughter) are visible on hides and skins. These defects, particularly on grain side, reduce the value of the leather. Aniline leather cannot be produced from such raw stock. (author)

Clinical Objective Dry Eye Tests in a Population of Tannery Workers in North India.

Science.gov (United States)

Ranjan, Ratnesh; Kushwaha, Raj Nath; Khan, Perwez; Mohan, Shalini; Gupta, Ramesh Chandra

2016-10-01

To analyze the correlation between subjective symptoms and clinical signs of dry eye among tannery workers. In this cross-sectional study, three classic clinical tests, namely the fluorescein tear film break-up time (FTBUT) test, the fluorescein staining (FS) test, and the Schirmer test (ST), were performed to assess the clinical signs of dry eye disease in 246 tanners who were found symptomatic for dry eye in a prior ocular surface disease index survey. All workers were male with a mean age of 35 ± 9 years, and the mean duration of work at tanneries was 8 ± 5 years. Among 246 symptomatic subjects, the FTBUT test, the FS test and the ST were positive in 63.8%, 30.9% and 41.9% workers, respectively. Mean FTBUT and ST scores were 10.6 ± 4.2 seconds and 10.1 ± 7.7mm, respectively. Mean FTBUT for mild, moderate and severe symptom categories differed significantly. Mean ST scores for the mild symptom group were significantly higher than that of the moderate group (p < 0.0001). The FTBUT and ST score showed a strong negative correlation with severity of symptoms (p < 0.0001). A moderate positive correlation was observed between FS positivity and increasing symptom severity (p < 0.0001). The effect of age was insignificant for FTBUT (p = 0.10), while significant for ST score (p < 0.001). The effect of duration of tannery work was significant for both FTBUT and ST scores (p < 0.0001). Clinical tests correlated well with symptom severity among tanners, and a multifactorial etiology is suggested for dry eye diseases.

Presence of toxic metals and their effects in finished leather goods

International Nuclear Information System (INIS)

Rana, B.B.; Ehsan, A.M.

2016-01-01

This study examines the presence of heavy metals in different types of leather finished goods. Various leather items like gloves, shoe soles and leather pieces for jackets were tested using Atomic Absorption Spectrophotometry and their toxic effects in our environment are discussed. Cadmium, lead and chromium are the most common heavy metals present in leather finished goods and are a cause for concern. Many countries in Europe and America have banned or limited their use in leather processing. This study reveals that the levels of heavy metals in most of the leather goods manufactured by different companies in Pakistan are within permissible limits. However, in some of the samples tested in this study, the amounts of cadmium, lead and chromium are considerably high which requires special attention from all stakeholders to bring it down to acceptable level. Failing to do so will be detrimental for export of these leather goods to Europe and America. (author)

Comparison of Jacket Production Processes Designed by Fabric Materials and Leather

Directory of Open Access Journals (Sweden)

Emine Utkun

2011-02-01

Full Text Available Leather and leather products industry has shown a significant improvement in export area, as a result of intensive shuttle trades and demand that comes from crumbling Eastern Bloc countries in 1990's. This development has caused capacity increasing and thus makes large investments in this sector. Leather garment industry differs from woven or fabrics industry at various points. Differantation seems in raw materials features such as size, thickness, biological, chemical or physical homogenity. Due to the natural structure, leather shows different attributes in different regions. This study examines the diversity of production processes of leather and fabric designed jacket.

Time-dependent effect of composted tannery sludge on the chemical and microbial properties of soil

NARCIS (Netherlands)

Sousa, de Ricardo Silva; Santos, Vilma Maria; Melo, de Wanderley Jose; Nunes, Luis Alfredo Pinheiro Leal; Brink, van den Paul J.; Araújo, Ademir Sérgio Ferreira

2017-01-01

Composting has been suggested as an efficient method for tannery sludge recycling before its application to the soil. However, the application of composted tannery sludge (CTS) should be monitored to evaluate its effect on the chemical and microbial properties of soil. This study evaluated the

Phytoextraction of heavy metals by Sesuvium portulacastrum l. a salt marsh halophyte from tannery effluent.

Science.gov (United States)

Ayyappan, Durai; Sathiyaraj, Ganesan; Ravindran, Konganapuram Chellappan

2016-01-01

The present study investigated the sources for remediation of heavy metals and salts from tannery effluent using salt marsh halophyte Sesuvium portulacastrum. From the results observed, in tannery effluent treated soil from 1 kg dry weight of plant sample, Sesuvium portulacastrum accumulated 49.82 mg Cr, 22.10 mg Cd, 35.10 mg Cu and 70.10 mg Zn and from 1 g dry weight of the plant sample, 246.21 mg Na Cl. Cultivation of Sesuvium portulacastrum significantly reduced the EC, pH and SAR levels in tannery effluent and salt treated soil and correspondingly increased in plant sample after 125 days of cultivation. In conclusion, Sesuvium portulacastrum was an efficient in accumulating heavy metals such as Chromium, Cadmium, Copper and Zinc, sodium and chloride maximum through its leaves when compared to stem and root. The finding of these bioacccumulation studies indicates that Sesuvium portulacastrum could be used for phytoremediation of tannery effluent contaminated field.

Chromed Leather Dyeing Peculiarities when Deliming with Peracetic Acid

Directory of Open Access Journals (Sweden)

Kęstutis BELEŠKA

2013-05-01

Full Text Available The research was aimed to investigate the influence of deliming with peracetic acid on leather dyeing kinetics. Hydrophobic C.I. Acid Red 213 and hydrophilic C.I. Acid Red 423 dyes were used. Sorption of dye depends on hydrophobicity/hydrophility of dye and dyeing temperature. Equilibrium of process is reached faster using hydrophobic C.I. Acid Red 213 at 45 ºC. However, both control and experimental leather fibres adsorb more hydrophilic dye C.I. Acid Red 423 and this fact does not depend on temperature. The diffusion coefficient of dye C.I. Acid Red 423 calculated according to Weisz model is higher when dyeing conventional leather. The change of deliming method has influence on chromed leather dyeing but this influence is not significant. The adsorption ability of control leather fibres at 30 ºC and 45 ºC is higher using both dyes as compared to the dyeing the experimental one. The increase of dyeing temperature increases the adsorption ability independently on the sort of leather fibres. Such dependence of the adsorption ability on the temperature shows that hydrophobic action and van der Waals forces prevail between dye and fibres during dyeing process. The Gibbs energy changes show that adsorption of both dyes by leather fibres independently on their sort is a spontaneous process. The affinity of both dyes to conventional leather fibres is higher comparing with experimental one. The change of enthalpy is positive in all cases, and it means that the driving force of the dyeing is the change of entropy.DOI: http://dx.doi.org/10.5755/j01.ms.19.2.4431

Semiautomatic machine for turning inside out industrial leather gloves

International Nuclear Information System (INIS)

Aragón-Gonzalez, G; Cano-Blanco, M; León-Galicia, A; Medrano-Sierra, L F; Morales-Gómez, J R

2015-01-01

The last step in the industrial leather gloves manufacturing is to turn the inside out so that the sewing be in the inside of the glove. This work presents the design and testing of a machine for that purpose. In order to quantify the relevant variables, testing was performed with a prototype glove. The employed devices and the testing proceeding were developed experimentally. The obtained information was used to build the turning inside out machine. This machine works with pneumatic power to carry the inside out turning by means of double effect lineal actuators. It has two independent work stations that could be operated simultaneously by two persons, one in each station or in single mode operating one station by one person. The turning inside out cycle is started by means of directional control valves operated with pedals. The velocity and developed force by the actuators is controlled with typical pneumatic resources. The geometrical dimensions of the machine are: 1.15 m length; 0.71 m width and 2.15 m high. Its approximated weight is 120 kg. The air consumption is 5.4 fps by each working station with 60 psig work pressure. The turning inside out operation is 40 s for each industrial leather glove

Short term preservation of hide using vacuum: influence on properties of hide and of processed leather.

Science.gov (United States)

Gudro, Ilze; Valeika, Virgilijus; Sirvaitytė, Justa

2014-01-01

The objective of this work was to investigate vacuum influence on hide preservation time and how it affects hide structure. It was established that vacuum prolongs the storage time without hide tissue putrefaction up to 21 days when the storage temperature is 4°C. The microorganisms act for all storage times, but the action is weak and has no observable influence on the quality of hide during the time period mentioned. The hide shrinkage temperature decrease is negligible, which shows that breaking of intermolecular bonds does not occur. Optical microscopy, infrared spectroscopy and differential scanning calorimetry also did not show any structural changes which can influence the quality of leather produced from such hide. The qualitative indexes of wet blue processed under laboratory conditions and of leather produced during industrial trials are presented. Indexes such as chromium compounds exhaustion, content of chromium in leather, content of soluble matter in dichloromethane, strength properties, and shrinkage temperature were determined. Properties of the leather produced from vacuumed hide under industrial conditions conformed to the requirements of shoe upper leather.

Hexavalent and trivalent chromium in leather: What should be done?

Science.gov (United States)

Moretto, Angelo

2015-11-01

Trivalent chromium compounds are used for leather tanning, and chromium may be released during use of leather goods. In certain instances, small amounts of hexavalent chromium can be formed and released. Both trivalent and hexavalent chromium can elicit allergic skin reaction in chromium sensitised subjects, the latter being significantly more potent. Induction of sensitisation only occurs after exposure to hexavalent chromium. A minority of subjects are sensitised to chromium, and in a fraction of these subjects allergic skin reaction have been described after wearing leather shoes or, less frequently, other leather goods. The evidence that in all these cases the reaction is related to hexavalent chromium is not always strong. The content of hexavalent chromium in leather is regulated in European Union, but rate of release rather than content is relevant for allergic skin reaction. The role of trivalent chromium appear much less relevant if at all. Modern tanning procedure do not pose significant risk due to either hexavalent or trivalent chromium. Dismissing bad quality and worn-off leather goods is relevant in reducing or eliminating the skin reaction. It should also be pointed out that shoe components or substances other than chromium in leather may cause allergic/irritative skin reactions. Copyright © 2015 Elsevier Inc. All rights reserved.

Anaerobic fluidized bed treatment of a tannery wastewater

Energy Technology Data Exchange (ETDEWEB)

Chen, S.J.; Li, C.T.; Shieh, W.K.

1988-11-01

The anaerobic fluidized bed system, in conjunction with neutralization and chemical coagulation/flocculation, was evaluated for treatment of a tannery wastewater produced from a chrome tanning operation. Neutralization with 1 N sulphuric acid was effective for removal of chromate, with complete removal achieved at pH=8.0. Chemical coagulation/flocculation with alum at a dosage of 200 mg/L was able to remove 97% of feed SS and 65% of feed grease. Evaluation of the performance of the anaerobic fluidized bed system indicated more than 75% of feed COD could be removed up to an F/M ratio of approximately 0.4 g COD/g TVS center dot day. The observed methane production rate was 0.221 of CH/sub 4/ produced per gram COD removed. The anaerobic fluidized bed system could provide an effective treatment of a pretreated tannery wastewater.

Environmental impacts of Sheba tannery (Ethiopia effluents on the surrounding water bodies

Directory of Open Access Journals (Sweden)

Abraha Gebrekidan

2009-08-01

Full Text Available The levels of hexavalent chromium from direct and treated Sheba tannery effluents, downstream river and spring water samples and upstream river water samples were determined spectrophotometrically by the s-diphenylcarbazide method at 540 nm. Temporal and representative samples were collected from the untreated tannery effluent (S1, sedimentation pond (S2, chromium oxidation pond (S3, downstream river (S4, downstream spring (S5 and 5 kms upstream river (S6. The mean levels of hexavalent chromium in S1, S2, S3, S4, S5 and S6 were 10.54, 9.15, 7.82, 0.58, 0.54 and 0.015 mg/L, respectively. The levels of hexavalent chromium in the downstream river and spring water samples exceed the World Health Organization (WHO permissible limit of total chromium in drinking waters (0.05 mg/L as opposed to the levels in the upstream waters. The increased concentrations of Cr(VI in the water samples indicate the possible environmental pollution of the downstream water bodies by the Sheba tannery effluents. In view of the toxicity and related environmental hazards, the levels of hexavalent chromium from the Sheba tannery effluents must be reduced to a permissible limit before discharging into the down stream waters being used for domestic purposes by the nearby communities.

Electron beam puts a shine on leather

International Nuclear Information System (INIS)

Berberich, S.

1986-01-01

A technique for curing leather using either ultraviolet or electron-beam radiation has been developed. This type of radiation curing saves at least 60 percent of the energy cost of conventional leather finishing and can also result in considerable savings in plant space and labor. The implications of the new technology in international balance of trade are discussed

Design of a biofilter to reduce the contamination content by chromium generated in the industries of the leather tanning

International Nuclear Information System (INIS)

Higuera C, Oscar F; Arroyave L, Juan F; Florez G, Luis

2009-01-01

The industrial sector of the tanneries generates unloadings with high volumes of chromium concentrates. The chromium is used in this industry like tanning agent. The tanning of skins presents some difficulties with the use of chromium salts, must to the great amount of tanning agent that does not fix to the skin and finally unloading to the environment, in waste waters causing negative effects in the environment and to the human health. The object of this work is to provide an alternative for the Chromium removal of waste water from tannery using coffee leaf variety castle, coffee Arabica

Internationalisation Barriers of Small and Medium-sized Manufacturing Enterprises in Ethiopia: Leather and Leather Products Industry in Focus

Directory of Open Access Journals (Sweden)

Yehualashet Demeke Lakew

2015-11-01

Full Text Available The purpose of this study was to examine internationalisation barriers of manufacturing SMEs operating in Leather and Leather Products Industry located in the capital city of Ethiopia. The small and medium sized enterprises (SMEs sector in Ethiopia is a significant group within the economy in terms of firm numbers and total employment. However, the SMEs sector’s share of exports is disproportionately small, which raised considerable research concerns. Firm export propensity was the dependent variable and internal and external export barrier factors were used as explanatory variables. The study was conducted through mixed research design of quantitative survey and case study. From the population of manufacturing SMEs operating in the Leather and Leather products Industry, a sample was selected through the use of stratified random sampling to ensure the effective representation of the population of exporting and non-exporting SMEs in the capital of Ethiopia. In order to complement survey results nine (4 exporting and 5 non-exporting SMEs were selected through critical case purposive sampling and an in-depth interviews were conducted. Statistical package for the social sciences (SPSS 20 was used to analyse the quantitative data whereas, qualitative data were analysed manually. Exploratory factor analysis with Varimax rotation and Binary logistic regression analysis are the analytical methods used. The statistical result showed that, logistics problem, insufficient finance, functional barriers, lack of export knowledge and information, procedural barriers and international trade barriers are the most significant obstacles of export trade in Ethiopia. The overall results revealed that explanatory variables used in the analysis significantly predict the dependent variable at 95% confidence level. Taken together, these results prompted the presentation of numerous implications for theory, practice, and future research. Finally, the paper recommended

Leather Industry Business Linkages (Case Study in District Magetan)

OpenAIRE

Dilahur Dilahur

2004-01-01

Leather industry in Magetan covers two forms; they are tanning and leathercraft. During 1960 and 1970, the leather industry decreased in its production, but in 1990 Magetan becomes the center of leather industry. Its development appeals to be studied closely. The goals of this study are to know the relation between tanning and leathercraft, the connection between these industries and other economic ativities, and their connection with production factor. This study uses survey methhod. The res...

Heavy metals and yield of cowpea cultivated under composted tannery sludge amendment

Directory of Open Access Journals (Sweden)

Iuna Carmo Ribeiro Gonçalves

2014-04-01

Full Text Available The study aimed to evaluate the phytoavailability of heavy metals (Cr, Cd, Ni and Pb concentrations in leaves and grains, and yield of cowpea (Vigna unguiculata L grown in soil amended with composted tannery sludge (CTS for two consecutive years. The experiments were carried out in 2009 and 2010 in soil amended with CTS at 0, 5, 10, 20, and 40 Mg ha-1. The CTS amendment rates applied were above 10 Mg ha-1, increased Cr concentrations in cowpea leaves. There were not increases in the heavy metals concentrations in cowpea grains after two years. In 2009, the application of CTS amendment did not promote increase in plant yield. However, in 2010, CTS amendment at 10 and 20 Mg ha-1 increased cowpea yield. The amendment of composted tannery sludge linearly increased linearly the concentration of Cr in the leaves of cowpea after two years. Composted tannery sludge promoted increases in cowpea yield.

Tannery Effluent Treatment by Yeast Species Isolates from Watermelon

Directory of Open Access Journals (Sweden)

Stanley Irobekhian Reuben Okoduwa

2017-02-01

Full Text Available The quest for an effective alternative means for effluent treatment is a major concern of the modern-day scientist. Fungi have been attracting a growing interest for the biological treatment of industrial wastewater. In this study, Saccharomycescerevisiae and Torulasporadelbrueckii were isolated from spoiled watermelon and inoculated into different concentrations of effluent. The inoculants were incubated for 21-days to monitor the performance of the isolates by measurement of biochemical oxygen demand (BOD, chemical oxygen demand (COD, nitrates, conductivity, phosphates, sulphates and turbidity. The results showed that Saccharomycescerevisiae had the highest percentage decrease of 98.1%, 83.0%, 60.7%, 60.5%, and 54.2% for turbidity, sulphates, BOD, phosphates and COD, respectively, of the tannery effluent. Torulasporadelbrueckii showed the highest percentage decrease of 92.9%, 90.6%, and 61.9% for sulphates, COD, and phosphates, respectively, while the syndicate showed the highest percentage reduction of 87.4% and 70.2% for nitrate and total dissolve solid (TDS, respectively. The least percentage decrease was displayed by syndicate organisms at 51.2%, 48.1% and 40.3% for BOD, COD and conductivity, respectively. The study revealed that Saccharomycescerevisiae and Torulasporadelbrueckii could be used in the biological treatment of tannery-effluent. Hence, it was concluded that the use of these organisms could contribute to minimizing the adverse environmental risks and health-hazards associated with the disposal of untreated tannery-effluents.

EXPLORING THE USE OF SUEDE DYE ON LEATHER

African Journals Online (AJOL)

User

Nguyen (2007) that almost all the world output of leather is produced ... The experiment on the use of suede dye on leather was done in three formats. In the first format, suede ... warm water in a plastic container in the first instance. Alum is a ...

Search Results | Page 4 | IDRC - International Development ...

International Development Research Centre (IDRC) Digital Library (Canada)

Results 31 - 40 of 51 ... Mongolia case study : "My Homeland" information system for ... Internet has been dominated by the English language and North American culture. ... of small leather tanneries that process some 30 000 skins per day, for a ...

POTENTIAL USE OF BUFFALO SKIN AS A RAW MATERIAL FOR LEATHER TANNING INDUSTRY IN INDONESIA

OpenAIRE

Said, Muhammad Irfan; Hifizah, Amriana

2013-01-01

Leather industry and leather goods industry in Indonesia reached the peak in1986-1996. Export of leather products (shoes, gloves, and jackets) contributed U.S. $ 2.4 billion to the government. Export of leather and leather products ranks third on the non-oil exports, the level after the export of textiles and wood. Since the economic crisis in Indonesia in 1997, nearly all industry sectors were collapsed, including the leather and leather products industry (Untari et al., 2009). The funda...

A Variable Neighborhood Search Algorithm for the Leather Nesting Problem

Directory of Open Access Journals (Sweden)

Cláudio Alves

2012-01-01

Full Text Available The leather nesting problem is a cutting and packing optimization problem that consists in finding the best layout for a set of irregular pieces within a natural leather hide with an irregular surface and contour. In this paper, we address a real application of this problem related to the production of car seats in the automotive industry. The high quality requirements imposed on these products combined with the heterogeneity of the leather hides make the problem very complex to solve in practice. Very few results are reported in the literature for the leather nesting problem. Furthermore, the majority of the approaches impose some additional constraints to the layouts related to the particular application that is considered. In this paper, we describe a variable neighborhood search algorithm for the general leather nesting problem. To evaluate the performance of our approaches, we conducted an extensive set of computational experiments on real instances. The results of these experiments are reported at the end of the paper.

Adsorption of leather dyes on activated carbon from leather shaving wastes: kinetics, equilibrium and thermodynamics studies.

Science.gov (United States)

Manera, Christian; Tonello, Andrezza Piroli; Perondi, Daniele; Godinho, Marcelo

2018-03-23

In this work, the adsorption of Acid Black 210 (AB210) and Acid Red 357 (AR357) onto activated carbon prepared from leather shaving wastes (ACLW) was investigated. The activated carbon presented a surface area of 800.4 m²/g with an average pore size of 1.27 nm. The kinetic study showed that the adsorption of both dyes followed the Elovich kinetic model while the AB210 and AR357 isotherm data were well described by the Langmuir and BET models, respectively. Furthermore, the Boyd plot revealed that the adsorption of the leather dyes on activated carbon was mainly governed by film diffusion. The pH had a strong influence on the adsorption, and the higher amounts of dye adsorbed were obtained at pH 2. The obtained activated carbon exhibited a high monolayer adsorption capacity of 573.9 and 204.4 mg/g for AB210 and AR357, respectively. Its high capacity is mainly attributed to its basicity (0.17 mmol/g) and high surface area. Desorption efficiency of the spent activated carbon was found to be 54.3% and 43.0% for AB210 and AR357, respectively. The spontaneity of the process was demonstrated by the negative values of the Gibbs free energy change.

Policy framework for formulating environmental management strategy for sustainable development of tanneries in India.

Science.gov (United States)

Ingle, Kapilkumar N; Harada, Koichi; Wei, Chang Nian; Minamoto, Keiko; Ueda, Atsushi

2011-03-01

The leather industry is one of the main examples of industries which play an important role in the Indian economy in terms of exports and employment opportunities, while being blamed for environmental pollution. The objective of this study was to find the advances or improvements in the Japanese leather industry which are not found in typical leather industries in developing countries. We examined the Japanese leather industry in this context because Japan is a developed country in which tanning processes have been a traditional business from ancient times, and also the leather industry has played an important role in the process of economic development of Japan. The study was based both on information collected from various areas related to the leather industry or leather industry stakeholders, and also on a review of published information. Information was collected through site visits, interviews, questionnaires, and detailed discussions with these stakeholders, as well as from their websites. The framework of a typical leather industry is discussed in three sections: pollution prevention, pollution control, and pollution mitigation related to sources, processes, and impact possibilities, respectively. Eleven basic differences were noted between the Japanese and Indian leather industries. The availability of melting centers is the main important feature of the Japanese leather sector. Guidelines are suggested which focus on some changes that are expected to lead to both environmental and economic benefits, with better pollution management, which should lead to continuous improvement of the environmental performance of the industry, and, finally, sustainable development.

THE INFLUENCE OF FATLIQOURING PROCESS ON PROTECTIVE CHARACTERISTICS OF LEATHER GLOVES

Directory of Open Access Journals (Sweden)

KILIÇ Eylem

2017-05-01

Full Text Available Appropriate protective gloves are essential for industry workers to avoid hands and wrists injuries. Leather is a common material used by professionals for technical gloves. Mechanical resistance, protection against water and high temperature has to be fulfilled by leather that is intended for using in protective gloves. In this study recipes using various fatliquoring agents with different properties such as lesitin based, lanolin based, polymeric based and water proofing fat liquor were applied to produce technical glove leather and effect of each fatliquoring product on protective performance of leathers were analyzed in terms of physical and mechanical properties including tensile (ISO 3376, stitch tear (ISO 23910, tear resistance (ISO 3377-2, static (ISO 2417 and dynamicwater absorption (ISO 5403-1 and thermal stability such as dry heat (ISO 17227 and heat stability (ISO 11645. For this purpose, chromium tanned split calf leathers were used and retanning of protective leather gloves were performed by using tara and phosphonium combination. Performance testing results obtained from four different retanning processes was compared according to the type of fatliquoring material used in the production. Post-tanning with different types of fatliquoring products have significant effect on the protective performance properties of leather gloves, in terms of mechanical and thermal properties.

Cr(III) and Cr(VI) in leather and elicitation of eczema

DEFF Research Database (Denmark)

Hansen, Malene Barré; Menne, Torkil; Johansen, Jeanne Duus

2006-01-01

The aim of the present study was to investigate the relation between the content of Cr(VI) and soluble Cr(III) in leather and the ability of the leather to elicit eczema in chromium allergic patients. An array of chromium-tanned leather samples was analysed for the content of total Cr(VI) and sol...

Arthrospira (Spirulina) in tannery wastewaters. Part 2: Evaluation of ...

African Journals Online (AJOL)

Part 2: Evaluation of tannery wastewater as production media for the mass culture of ... as a critical driver in the profitability of the algal biotechnology enterprise. ... and possibly marginal economics of, biofuels production from the microalgae ...

Solid waste from leather industry as adsorbent of organic dyes in aqueous-medium

International Nuclear Information System (INIS)

Oliveira, Luiz C.A.; Goncalves, Maraisa; Oliveira, Diana Q.L.; Guerreiro, Mario C.; Guilherme, Luiz R.G.; Dallago, Rogerio M.

2007-01-01

The industrial tanning of leather usually produces considerable amounts of chromium-containing solid waste and liquid effluents and raises many concerns on its environmental effect as well as on escalating landfill costs. Actually, these shortcomings are becoming increasingly a limiting factor to this industrial activity that claims for alternative methods of residue disposals. In this work, it is proposed a novel alternative destination of the solid waste, based on the removal of organic contaminants from the out coming aqueous-residue. The adsorption isotherm pattern for the wet blue leather from the Aurea tanning industry in Erechim-RS (Brazil) showed that these materials present high activity on adsorbing the reactive red textile dye as well as other compounds. The adsorbent materials were characterized by IR spectroscopy and SEM and tested for the dye adsorption (reactive textile and methylene blue dyes). The concentrations of dyes were measured by UV-vis spectrophotometry and the chromium extraction from leather waste was realized by basic hydrolysis and determined by atomic absorption. As a low cost abundant adsorbent material with high adsorption ability on removing dye methylene blue (80 mg g -1 ) and textile dye reactive red (163 mg g -1 ), the leather waste is revealed to be a interesting alternative relatively to more costly adsorbent materials

Solid waste from leather industry as adsorbent of organic dyes in aqueous-medium

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Luiz C.A. [Universidade Federal de Lavras, Depto. de Quimica, Caixa Postal 37, CEP 37200.000, Lavras-MG (Brazil)]. E-mail: luizoliveira@ufla.br; Goncalves, Maraisa [Universidade Federal de Lavras, Depto. de Quimica, Caixa Postal 37, CEP 37200.000, Lavras-MG (Brazil); Oliveira, Diana Q.L. [Universidade Federal de Lavras, Depto. de Quimica, Caixa Postal 37, CEP 37200.000, Lavras-MG (Brazil); Guerreiro, Mario C. [Universidade Federal de Lavras, Depto. de Quimica, Caixa Postal 37, CEP 37200.000, Lavras-MG (Brazil); Guilherme, Luiz R.G. [Universidade Federal de Lavras, Depto. de Ciencia do solo, CEP 37200.000, Lavras-MG (Brazil); Dallago, Rogerio M. [URI-Campus Erechim, Av. 7 Setembro 1621, Centro, CEP 99700-000, Depto de Quimica, Erechim-RS (Brazil)

2007-03-06

The industrial tanning of leather usually produces considerable amounts of chromium-containing solid waste and liquid effluents and raises many concerns on its environmental effect as well as on escalating landfill costs. Actually, these shortcomings are becoming increasingly a limiting factor to this industrial activity that claims for alternative methods of residue disposals. In this work, it is proposed a novel alternative destination of the solid waste, based on the removal of organic contaminants from the out coming aqueous-residue. The adsorption isotherm pattern for the wet blue leather from the Aurea tanning industry in Erechim-RS (Brazil) showed that these materials present high activity on adsorbing the reactive red textile dye as well as other compounds. The adsorbent materials were characterized by IR spectroscopy and SEM and tested for the dye adsorption (reactive textile and methylene blue dyes). The concentrations of dyes were measured by UV-vis spectrophotometry and the chromium extraction from leather waste was realized by basic hydrolysis and determined by atomic absorption. As a low cost abundant adsorbent material with high adsorption ability on removing dye methylene blue (80 mg g{sup -1}) and textile dye reactive red (163 mg g{sup -1}), the leather waste is revealed to be a interesting alternative relatively to more costly adsorbent materials.

[Research on source profile of aerosol organic compounds in leather plant].

Science.gov (United States)

Wang, Bo-Guang; Zhou, Yan; Feng, Zhi-Cheng; Liu, Hui-Xuan

2009-04-15

Through investigating current air pollution condition for PM10 in every factories of different style leather plants in Pearl River Delta, characteristic profile of semi-volatile organic compounds in PM10 emitted from leather factories and their contents were researched by using ultrasonic and gas chromatography and mass spectrum technology. The 6 types of organic compounds containing 46 species in total were found in the collected samples, including phenyl compounds, alcohols, PAHs, acids, esters and amides. The concentrations of PM10 in leather tanning plant, leather dying plant and man-made leather plant were 678.5, 454.5, 498.6 microgm x m(-3) respectively, and concentration of organic compounds in PM10 were 10.04, 6.89, 14.21 microg x m(-3) in sequence. The more important type of pollutants in each leather plants had higher contribution to total organic mass as follows, esters and amides in tanning plants profile account for 43.47% and 36.51% respectively; esters and alcohols in dying plants profiles account for 52.52% and 16.16% respectively; esters and amide in man-made leather plant have the highest content and account for 57.07% and 24.17% respectively. In the aerosol organic source profiles of tested leather plants, 9-octadecenamide was the abundant important species with the weight of 26.15% in tanning plant, and Bis(2-ethylhexyl) phthalate was up to 44.19% in the dying plant, and Bis(2-ethylhexyl) maleate and 1-hydroxy-piperidine had obviously higher weight in man-made plant than the other two plants.

Characterization of waste waters of tannery, fertilizer and textile industries in Multan region

International Nuclear Information System (INIS)

Ansan, T.M.; Malik, S.A.

2001-01-01

This study evaluates various physico-chemical characteristics such as pH, electrical conductivity, dissolved solids, hardness, apparent color, odor, elemental concentrations, chloride contents, carbonates, bicarbonates, residual sodium carbonate and sodium absorption ratio of waste waters of three major industries, i.e. tannery, fertilizer and textile, situated in Multan District of the Punjab province, Pakistan. Waste waters, in general, have been found to be hard, alkaline in nature and contain variable amounts of dissolved solids. High concentration of chromium (10.7 mg 1-1) was found in tannery wastewater. Zinc and copper concentrations were not quantifiable. Water quality classes (C4-S4), (C4-S1) and (C4-S1, C3-S1, C3-S4 and C3-S2) have been assigned to tannery, fertilizer and textile waste waters respectively. Results indicate that these untreated industrial waste waters are potential hazards to human health and unsuitable for irrigation usage. (author)

Consumer leather exposure: an unrecognized cause of cobalt sensitization

DEFF Research Database (Denmark)

Thyssen, J.P.; Johansen, Jeanne D.; Jellesen, Morten Stendahl

2013-01-01

BACKGROUND: A patient who had suffered from persistent generalized dermatitis for 7 years was diagnosed with cobalt sensitization, and his leather couch was suspected as the culprit, owing to the clinical presentation mimicking allergic chromium dermatitis resulting from leather furniture exposur...

Consumer Preference Towards Fruit Leather Attributes of Madurese Exotic Tropical Fruits

Directory of Open Access Journals (Sweden)

Elys Fauziyah

2018-01-01

Full Text Available Madura island has high potential for producing tropical fruits, but it still not being well managed especially concerning with the value added Fruit leather is a product created by using various fruits and simple technology application. Fruit leather is categorized as new product on the market, therefore it is important to know consumer preference towards fruit leather attributes so that producer can design an acceptable product in the market. The research investigated attributes within the levels that become consumer preference in purchasing fruit leather product. There were 60 samples respondents taken accidentally at Bangkalan Plaza Shopping area. Method being used was conjoint analysis. Result showed that fruit leather being chosen by consumers as preference are gummy, mixed fruit taste, yellow color small roll shape, at 100 grams and in a plastic tube package.

Evaluation of fruit leather made from two cultivars of papaya

Directory of Open Access Journals (Sweden)

ZUHAIR RADHI ADDAI

2016-03-01

Full Text Available Two papaya cultivars were used to manufacture fruit leather. The objective of this study was to formulate papaya leather from locally grown papaya using natural ingredients like pectin, honey and citric acid. The fresh fruits were pureed and mix with natural ingredients, and dried in an oven at 60°C for 12 hours. The physicochemical properties and antioxidant activity were determined.The results showed that fruit leather made from Hongkong cultivar is significantly (P<0.05 higher in sensory parameters as well as physicochemical properties and antioxidant activity. The phenolics content and antioxidant activity increased by process of drying the fruit leather compared to fresh fruits in both papaya cultivars. Therefore, the consumer requirements for healthy and safe food products were respected.

Characterization and antimicrobial performance of nano silver coatings on leather materials

Directory of Open Access Journals (Sweden)

N. Lkhagvajav

2015-03-01

Full Text Available In this study, the characterization and the antimicrobial properties of nano silver (nAg coating on leather were investigated. For this purpose, turbidity, viscosity and pH of nAg solutions prepared by the sol-gel method were measured. The formation of films from these solutions was characterized according to temperature by Differential Thermal Analysis-Thermogravimetry (DTA-TG equipment. The surface morphology of treated leathers was observed using Scanning Electron Microscopy (SEM. The antimicrobial performance of nAg coatings on leather materials to the test microorganisms as Escherichia coli, Staphylococcus aureus, Candida albicans and Aspergillius niger was evaluated by the application of qualitative (Agar overlay method and quantitative (percentage of microbial reduction tests. According to qualitative test results it was found that 20 μg/cm2 and higher concentrations of nAg on the leather samples were effective against all microorganisms tested. Moreover, quantitative test results showed that leather samples treated with 20 μg/cm2 of nAg demonstrated the highest antibacterial activity against E. coli with 99.25% bacterium removal, whereas a 10 μg/cm2 concentration of nAg on leather was enough to exhibit the excellent percentage reduction against S. aureus of 99.91%. The results are promising for the use of colloidal nano silver solution on lining leather as antimicrobial coating.

Surface modification of polyester synthetic leather with tetramethylsilane by atmospheric pressure plasma

Energy Technology Data Exchange (ETDEWEB)

Kan, C.W., E-mail: tccwk@polyu.edu.hk [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Kwong, C.H. [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Ng, S.P. [Hong Kong Community College, The Hong Kong Polytechnic University (Hong Kong)

2015-08-15

Highlights: • Atmospheric pressure plasma treatment improved surface performance of polyester synthetic leather with tetramethylsilane. • XPS and FTIR confirmed the deposition of organosilanes on the sample's surface. • Contact angle increases to 138° after plasma treatment. - Abstract: Much works have been done on synthetic materials but scarcely on synthetic leather owing to its surface structures in terms of porosity and roughness. This paper examines the use of atmospheric pressure plasma (APP) treatment for improving the surface performance of polyester synthetic leather by use of a precursor, tetramethylsilane (TMS). Plasma deposition is regarded as an effective, simple and single-step method with low pollution. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) confirm the deposition of organosilanes on the sample's surface. The results showed that under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP treated sample with sessile drop static contact angle of 138°. The hydrophobic surface is stable without hydrophilic recovery 30 days after plasma treatment.

Surface modification of polyester synthetic leather with tetramethylsilane by atmospheric pressure plasma

International Nuclear Information System (INIS)

Kan, C.W.; Kwong, C.H.; Ng, S.P.

2015-01-01

Highlights: • Atmospheric pressure plasma treatment improved surface performance of polyester synthetic leather with tetramethylsilane. • XPS and FTIR confirmed the deposition of organosilanes on the sample's surface. • Contact angle increases to 138° after plasma treatment. - Abstract: Much works have been done on synthetic materials but scarcely on synthetic leather owing to its surface structures in terms of porosity and roughness. This paper examines the use of atmospheric pressure plasma (APP) treatment for improving the surface performance of polyester synthetic leather by use of a precursor, tetramethylsilane (TMS). Plasma deposition is regarded as an effective, simple and single-step method with low pollution. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) confirm the deposition of organosilanes on the sample's surface. The results showed that under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP treated sample with sessile drop static contact angle of 138°. The hydrophobic surface is stable without hydrophilic recovery 30 days after plasma treatment

NEW ECO-EFFICIENT PRODUCTS USED IN LEATHER INDUSTRY

Directory of Open Access Journals (Sweden)

ROSU Dan

2016-05-01

Full Text Available In today's move to "sustainable production" the leather industry, as well as many other industries is recognized as a polluting one. Traditional chemical operations are polluting because of the levels of inorganic chemical waste. Process chemicals which are not consumed within the reactions necessary to convert collagen to leather are currently discharged to waste. These are usually applied during bulk production, such as inorganic agents from beam house and tanning processes, e.g. lime, sulphide, ammonium salts, sulphuric acid and sodium chloride, mineral tanning agents – mainly Cr(III and the less common Al(III, Zr(III, Ti(III, Fe(III salts -, whereas depending on the tanning process and the leather article produced organic chemical waste discharged comprises aldehydic and polyphenolic tanning products, bating enzymes, organic carboxylic acids and excess electrolyte stable synthetic fat liquors. It is rare for chemicals and water to be recovered for re-use from several of these process steps. Moreover, tanners worldwide are required to operate within strict legislative boundaries. Serious drawbacks continuously arise concerning the chrome–tanning process in leather industry and the environmental hazardous consequences of chromium containing effluents. In order to overcome this impediment, a great deal of research has been focused on developing chrome–free tanning methods in the past years, such as titanium tanning. In the present study, Ti–Al tanned bovine leather was characterized by means of SEM microscopy, EDAX elemental analysis, ATR–FTIR spectroscopy, thermogravimetry TGA, and differential scanning calorimetry DSC techniques.

Fabrication of silver nanoparticle sponge leather with durable antibacterial property.

Science.gov (United States)

Liu, Gongyan; Haiqi, Gao; Li, Kaijun; Xiang, Jun; Lan, Tianxiang; Zhang, Zongcai

2018-03-15

Leather product with durable antibacterial property is of great interest both from industry and consumer's point of view. To fabricate such functional leather, gallic acid modified silver nanoparticles (GA@AgNPs) were first in situ synthesized with a core-shell structure and an average size of 15.3nm. Due to its hydrophilic gallic acid surface, the GA@AgNPs possessed excellent stability and dispersibility in wide pH range from 3 to 12 and also showed effective antibacterial activity with a minimum inhibitory concentration (MIC) of around 10μgmL -1 . Then, such GA@AgNPs were used as retanning agent to be successfully filled into leather matrix during the leather manufacturing process. Moreover, taking the advantage of its high surface density of carboxyl groups, these GA@AgNPs could be further chemically cross-linked onto collagen fibers by chrome tanning agent. After retanning, the resultant leather was given a "AgNPs sponge" feature with high payload of silver nanoparticles against laundry, exhibiting high and durable antibacterial activity. Copyright © 2017 Elsevier Inc. All rights reserved.

Bioremediation of Tannery Wastewater by Chromium Resistant Fungal Isolate Fusarium Chlamydosporium SPFS2-g

OpenAIRE

Smiley Sharma; Piyush Malaviya

2014-01-01

The present study assessed the bioremediation potential of Fusarium chlamydosporium SPFS2-g isolated from tannery effluent enriched soil. The isolate exhibited minimum inhibitory concentration (MIC) for Cr(VI) as 500 ppm. The treatment of tannery wastewater with Fusarium chlamydosporium in shake flask experiment resulted in the reduction of chemical oxygen demand (COD), color, Cr(VI), total suspended solids (TSS), turbidity, Na+, Cl-, and NO3- in the order of 71.80, 64.69, 100, 36.47, 22.77,...

Life cycle assessment as a tool for the environmental improvement of the tannery industry in developing countries.

Science.gov (United States)

Rivela, B; Moreira, M T; Bornhardt, C; Méndez, R; Feijoo, G

2004-03-15

A representative leather tannery industry in a Latin American developing country has been studied from an environmental point of view, including both technical and economic analysis. Life Cycle Analysis (LCA) methodology has been used for the quantification and evaluation of the impacts of the chromium tanning process as a basis to propose further improvement actions. Four main subsystems were considered: beamhouse, tanyard, retanning, and wood furnace. Damages to human health, ecosystem quality, and resources are mainly produced by the tanyard subsystem. The control and reduction of chromium and ammonia emissions are the critical points to be considered to improve the environmental performance of the process. Technologies available for improved management of chromium tanning were profoundly studied, and improvement actions related to optimized operational conditions and a high exhaustion chrome-tanning process were selected. These actions related to the implementation of internal procedures affected the economy of the process with savings ranging from US dollars 8.63 to US dollars 22.5 for the processing of 1 ton of wet salt hides, meanwhile the global environmental impact was reduced to 44-50%. Moreover, the treatment of wastewaters was considered in two scenarios. Primary treatment presented the largest reduction of the environmental impact of the tanning process, while no significant improvement for the evaluated impact categories was achieved when combining primary and secondary treatments.

Cytogenetic effects of leachates from tannery solid waste on the somatic cells of Vicia faba.

Science.gov (United States)

Chandra, Saurabh; Chauhan, L K S; Pande, P N; Gupta, S K

2004-04-01

The contamination of surface- and groundwater by the leaching of solid wastes generated by industrial activities as a result of water runoff and rainfall is a matter of great concern. The leachates from tannery solid waste (TSW), a major environmental pollutant, were examined for their possible genotoxic effects on the somatic cells of Vicia faba. Leachates were prepared from solid wastes procured from leather-tanning industrial sites, and V. faba seedlings were exposed to three test concentrations, 2.5%, 5%, and 10%, through soil and aqueous media for 5 days. The root tips examined for cytogenetic damage revealed that leachate of TSW significantly inhibited the mitotic index and induced significantly frequent chromosomal and mitotic aberrations (CA/MA) in a dose-dependent manner. The chemical analysis of TSW samples revealed that the chief constituents were chromium and nickel, which may cause genetic abnormalities. The frequency of aberrations was found to be higher in the root meristematic cells of Vicia faba exposed through the aqueous medium than those exposed through the soil medium. The results of the present study indicated that contamination of potable water bodies by leachates of TSW may cause genotoxicity. For the biomonitoring of complex mixtures of toxicants with the V. faba bioassay, the use of the aqueous medium seems to be a more promising method than the use of the soil medium. Copyright 2004 Wiley Periodicals, Inc. Environ Toxicol 19: 129-133, 2004.

13, 2014 1 Production and characterization of biodiesel

African Journals Online (AJOL)

The possibility of biodiesel production from traditional tannery fleshing wastes was ... Based on worldwide standard procedures (ASTM specification), the biodiesel fuel ... affect economic and social development (Eisenberg ... Besides, the low cost of non-edible oils as raw ..... seed, leather industry fleshing wastes, corn germ.

Trade Union Participation in Organized Leather Industry in Kolkata ...

African Journals Online (AJOL)

The paper attempts to evaluate the significance of different factors determining the trade union participation in organized leather industry in Kolkata. The research has been conducted based on three sample leather units engaged in three different commercial functions and these units have been selected based on types of ...

[Spectral Analysis of Dissolved Organic Matter of Tannery Wastewater in the Treatment Process].

Science.gov (United States)

Fan, Chun-hui; Zhang, Ying-chao; Du, Bo; Song, Juan; Huai, Cui-qian; Wang, Jia-hong

2015-06-01

Tannery industry is one of the major traditional industries and important wastewater sources in China. The existing research mainly focus on the quality of inlet and outlet water, rather than the purification and transformation behavior of dissolved organic matter (DOM) in the treatment process of tannery wastewater. The UV spectra and fluorescence spectroscopy were used to detect the spectral characteristics of water samples in the treatment process, and it is analyzed that the formation process and the linear relationships between total fluorescence intensity and parameters. The results showed: the UV absorbance of DOM in wastewater increased firstly and then decreased with longer wavelength, and the wave peaks were found around the wavelength of 230 nr. The values of A253 /A203 and SUVA254 increased firstly and then decreased, indicating the complex reaction process related to free substituent and aromatic rings. The fluorescence peaks appeared at the regions of λ(ex/em) = 320-350/440- 460 and λ(ex/em) = 270-300/390-420, referred as visible humic-like and visible fulvic-like fluorescence, respectively. With the treatment process of tannery wastewater, the following fluorescence phenomenon were monitored, such as the blue-shift of humic-like fluorescence peak in the hydrolytic acidification tank, the appearance of tryptophan fluorescence peak in the second biochemical pond (λ(ex/em) = 290/340), the weak fluorescence peak in the fourth biochemical pond (λ(ex/em) = 350/520) and the stabilized fluorescence characteristics in the secondary sedimentation tank and water outlet. The achievements are helpful to investigate the degradation and formation behavior of water components, and significant for the fluorescence variation analysis in the treatment system. The removal rate of total fluorescence intensity of tannery wastewater fit better the removal rate of TOC with coefficient of r 0.835 5. The UV spectra and 3D-EEMs are effective to reveal the purification

Conservation of leather historical object by nano technology in ...

African Journals Online (AJOL)

This paper examines the conservation of Antibacterial by Nano materials in the manufacture of leather and the implication of such a processes deteriorated of aging leather. As a sample study to improve this process historical cover book is used. Experimental methods are SEM EDX, Cultural Bacterial, Nano materials such ...

THE CHROME-TANNED GOAT LEATHER FOR HIGH QUALITY OF BATIK

Directory of Open Access Journals (Sweden)

W. Pancapalaga

2015-09-01

Full Text Available in which the first stage aimed to evaluate sodium silica as batik wax releasing agent on chrome leather.Completely randomized design (CRD was applied in this study. The concentration of sodium silica wastreated as treatments, in which Tl = 0, T2 = 2 g/L, T3: 4 g/L and T4 = 6 g/L. The second stage of thestudy was aimed to evaluate the type of dye used in batik method dyeing on chrome-tanned goat leather.CRD was used and the treatments were types of dye, i.e. T'1 = acid, T'2= indigosol, T'3 = napthol, T'4 =remazol. In both studies, 9 replicates were applied for each treatment. The use of sodium silicateconcentration of 2 g/L resulted in the percentage of release wax of 91.4% and did not degrade the qualityof chrome leather. The type of acid dyes and naphthol provided the best adhesion and color brightnessand resistance to washing treatment, water, sweat, bend, and rub at 4/5 to 5 on a scale of gray. Inconclusion, chrome tanned goat leather with batik dyeing method was recommended to become one ofthe raw materials of leather goods.

Artificially modified collagen fibril orientation affects leather tear strength.

Science.gov (United States)

Kelly, Susyn J; Wells, Hannah C; Sizeland, Katie H; Kirby, Nigel; Edmonds, Richard L; Ryan, Tim; Hawley, Adrian; Mudie, Stephen; Haverkamp, Richard G

2018-07-01

Ovine leather has around half the tear strength of bovine leather and is therefore not suitable for high-value applications such as shoes. Tear strength has been correlated with the natural collagen fibril alignment (orientation index, OI). It is hypothesized that it could be possible to artificially increase the OI of the collagen fibrils and that an artificial increase in OI could increase tear strength. Ovine skins, after pickling and bating, were strained biaxially during chrome tanning. The strain ranged from 2 to 15% of the initial sample length, either uniformly in both directions by 10% or with 3% in one direction and 15% in the other. Once tanned, the leather tear strengths were measured and the collagen fibril orientation was measured using synchrotron-based small-angle X-ray scattering. The OI increased as a result of strain during tanning from 0.48 to 0.79 (P = 0.001) measured edge-on and the thickness-normalized tear strength increased from 27 to 43 N mm -1 (P leather was strained 10% in two orthogonal directions. This is evidence to support a causal relationship between high OI (measured edge-on), highly influenced by thickness, and tear strength. It also provides a method to produce stronger leather. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Metal Contamination In Plants Due To Tannery Effluent

Directory of Open Access Journals (Sweden)

Md. Farhad Ali

2015-08-01

Full Text Available Abstract This paper analyzes the determination of heavy metals named Chromium Lead and Cadmium deposited in soil as well as in the plants and vegetables due to the tanning industries of the area of Hazaribagh Dhaka. The tanneries discharge untreated tannery effluents which get mixed with the soil water of rivers and canals in this area. The determination of metals was performed for the soil that was collected from the land adjacent to the canals which bear untreated tannery effluents. The soil is affected with the untreated effluents through the deposition of heavy metals. The metals were furthers deposited into the plants and vegetables grown on that soil. The roots stems and leaves of the plants of Jute Corchorus capsularis and Spinach Basella alba grown on that soil were analyzed for determining these metals. Extreme amount of chromium was found for plants and again Lead Cadmium were found in higher amount in these parts of the two plants. These two plants are taken as a popular vegetables extensively. In case of soil the amount of Chromium Lead and Cadmium were analyzed as 87 mgL 0.131 mgL and 0.190 mgL respectively. For the roots stems and leaves of Jute Corchorus capsularis the average values are 115.62 mgL for Chromium 11.25 mgL for Lead and 2.27 mgL for Cadmium respectively. Again in case of Spinach Basella alba 124.42 mgL was found for Chromium 7.38 mgL for lead and 2.97 mgL for Cadmium as average values for these parts of the two trees. All the observed values of metals of Chromium Lead and Cadmium are higher than the permissible and specially for Chromium the amount is extremely higher.

Utilization of heavy metal-rich tannery sludge for sweet basil (Ocimum basilicum L.) cultivation.

Science.gov (United States)

Chand, Sukhmal; Singh, Shweta; Singh, Vinay Kumar; Patra, D D

2015-05-01

Unlike food crops, essential oil-bearing crops in which the oil is extracted through hydro-distillation can be a suitable crop to be grown in heavy metal-polluted soils as the oil does not carry any heavy metal. In a field experiment conducted at CIMAP, Lucknow, India during 2011 and 2012, influence of six doses of tannery sludge viz 0, 10, 20, 30, 40, and 50 t ha(-1) were tested, taking sweet basil (Ocimum basilicum) as the test crop. Maximum herb yield was obtained with the application of sludge at 20 t ha(-1). While in root, accumulation of Cd and Pb increased significantly up to 20 t ha(-1), Cr accumulation increased with increasing the dose of tannery sludge reaching maximum at 50 t ha(-1). Essential oil yield of basil (Ocimum basilicum) was significantly affected due to sludge application. Quality of essential oil, in term of chemical constituents, however, was marginally influenced due to tannery sludge application.

Fingermark Development on Leathers: Visualisation and Species Differentiation

OpenAIRE

Nichols-Drew, L.; Hillman, R.; Coulston, J.

2017-01-01

The Society for Wildlife Forensic Sciences - 2017 Conference Edinburgh The uniqueness of fingermarks provides identification of an individual. In practice, most such marks are latent: selection of the optimum reagent to render them visible depends on the nature of the surface and the object’s history. Despite availability of many processes, some “difficult” surfaces with low fingermark recovery rates remain: leather is a prime example. The generic goal of this work is visualisation of late...

Comparison of Jacket Production Processes Designed by Fabric Materials and Leather

OpenAIRE

Emine Utkun; Ziynet Öndoğan

2011-01-01

Leather and leather products industry has shown a significant improvement in export area, as a result of intensive shuttle trades and demand that comes from crumbling Eastern Bloc countries in 1990's. This development has caused capacity increasing and thus makes large investments in this sector. Leather garment industry differs from woven or fabrics industry at various points. Differantation seems in raw materials features such as size, thickness, biological, chemical or physical homogenity....

Enrichment, risk assessment, and statistical apportionment of heavy metals in tannery-affected areas

International Nuclear Information System (INIS)

Ali, Z.; Malik, R. N.; Shinwari, Z. K.; Qadir, A.

2015-01-01

Tannery-affected surface soils from 72 sampling sites from industrial area of Sialkot district, Pakistan, were collected and analyzed for nine physicochemical parameters, nine heavy metals, and four macro-nutrients. Most of the soils were poor in organic matter (0.11–2.98 %), basic in nature with p H (7.1–10.6) and electrical conductivity (1.2–17.9 mS/ cm). Mean concentration of total dissolved solids, Cl 1 -, alkalinity, NO 1 -N, salinity, and PO 4 3- was 3,093 mg/L, 6,587, 3,929, 301.3, 10.3, and 1.7 mg/kg. The results showed that concentration of macro-nutrients was in the order: Na[Mg[K[Ca whereas heavy metals followed the order: Cr>Fe>Ni>Mn>Cu>Zn>Co>Pb>Cd. Factor analysis based on principal component analysis, cluster analysis, and correlation analysis identified contribution of metals from tannery effluents, agrochemicals, automobiles exhaust, and natural weathering processes. Tannery-affected soils were enriched with Cd followed by Cr, Pb, Ni, Cu, Co, Zn, and Mn. Geo-accumulation index classified the soil samples in unpolluted tomoderately polluted categories. Metal pollution index provided better estimation of heavy metal pollution as compared to pollution load index. Ecological risk index showed high potential ecological risk associated with Cd and Cr with mean concentrations above respective average shale/ background values. The results are useful for heavy metals source identification, enrichment, risk assessment, and management of tannery-affected soils and can contribute to monitoring programs at regional levels.

Pollution from tanneries effluents and its impact on environment

International Nuclear Information System (INIS)

Rajput, A.A.; Memon, Hafeez-ur-Rahman; Sahto, M.H.

1999-01-01

The disposal of tanneries effluence has become one of the serious environmental problems. The effluents from tanneries contain highly toxic materials, including chromium salts, ammonium salts, acids, sodium sulphide and suspended solids. Hair, alkalinity, surfactants, dyes and oils are also present in these effluents. The extent of pollution depends upon the volume of the effluent discharged. Many studies have been carried out on the characteristics of these effluents in order to understand the nature of the effluents and their impact on environment. The present study shows measured values of different parameters like Biochemical Oxygen Demand (BOD) about 1950 mg/l, Chemical Oxygen Demand (COD) about 4500-4600 mg/l, suspended solids about 2600-2700 mg/l, dissolved solids 10000-12000 mg/l and lead, copper, chromium and cadmium about 2, 0.4, 64.4 and 0.31 mg/l respectively. The measured values are compared with that of previous. Some remedial measures for its treatment and disposal are also discussed. (author)

Consumer Preference Towards Fruit Leather Attributes of Madurese Exotic Tropical Fruits

OpenAIRE

Elys Fauziyah

2018-01-01

Madura island has high potential for producing tropical fruits, but it still not being well managed especially concerning with the value added Fruit leather is a product created by using various fruits and simple technology application. Fruit leather is categorized as new product on the market, therefore it is important to know consumer preference towards fruit leather attributes so that producer can design an acceptable product in the market. The research investigated attributes within the l...

EFFECTS OF FATLIQURING PROCESS ON LEATHERS COLOURED WITH IR REFLECTIVE DYES AND PIGMENTS

Directory of Open Access Journals (Sweden)

MUTLU Mehmet Mete

2017-05-01

Full Text Available Black coloured materials and consumer goods are known to be heating up more, because they absorb sun radiation more than light colours. This heating is a problem for the users for black automotive or motorcycle leathers and also for dark shoes and boots which are exposed to sun heat. Human vision system can distinguish visible colours between the wavelengths of 390-700 nm. So reflecting the sun radiation in the infrared area of radiation spectrum higher than 700nm, is a solution for heating problem without affecting the visible colour. For this reason IR reflective dyes and pigments are designed. A leading Leather Chemical Company has developed an IR reflecting dyeing system for leather keeping the dark coloured leathers cooler under sun radiation. Additionally in theory, fat and water content of leather affects its heating properties. In this study, effect of natural, synthetic and waterproof fatliquoring systems on heating properties of leathers coloured with IR reflective dyes and pigments are investigated.

Preparation of high exhaust chrome from leather shavings and hydrocarbons with its application in leather processing for green tanning technology

International Nuclear Information System (INIS)

Nawaz, H.R.; Solangi, B.A.; Nadeem, U.; Zehra, B.

2010-01-01

The use of chrome in tanning has made the remarkable advances to achieve the best quality and quantity of leather. But the chrome tanning process is associated with the generation of heavy metal containing solid wastes and toxic effluents. To solve the environmental issues we emphasized on the development of high exhaust chrome complex from chrome containing leather wastes that could minimize the toxic effluents up to negligible limit. Therefore in the synthetic process of chrome tanning material, the chrome shavings and the hydrocarbons have been utilized as a reductant as well as the potential masking intermediates. These chrome tanning materials have been prepared using leather shavings alone in product A, partial replacement of shavings by hydrocarbons for product B and then replacement of hydrocarbons by molasses for product C. The materials have been employed for the tanning of goat skins parallel to the commercial basic chromium sulfate (BCS). (author)

Characterisation of 17th-18th centuries damask and gilt leathers by ATR-FTIR

Directory of Open Access Journals (Sweden)

Lina Falcão

2018-01-01

Full Text Available In this paper it is presented the characterisation of tannins used in the vegetable tanning of two types of European historic and decorative leathers from Portuguese collections, damask leathers and gilt leathers, dated from the 17th and 18th centuries. Extracts prepared from collected leather fibres were analysed by attenuated total reflectance – Fourier transform infrared (ATR-FTIR spectroscopy. Results were compared with data collected from different reference vegetable tanning materials which, according to historic and technical literature, were used in Europe during the Modern Age. This study allowed, in most cases, the characterisation of the tannins used to produce the studied decorative vegetable tanned leathers and, at the same time, the detection of chemical deterioration of leathers, particularly collagen hydrolysis, which was not visually perceived.

Analysis of tannery effluents from the Challawa industrial estate in ...

African Journals Online (AJOL)

Global Journal of Pure and Applied Sciences ... and some physicochemical parameters such as conductivity, solids, chloride, chromium, alkalinity, sulphide, chemical oxygen demand, COD, and biochemical oxygen demand, BOD, of the waste water were determined. ... Keywords: tannery, effluent, pollution, environment

Using of Hyperbranched Poly(amidoamine as Pretanning Agent for Leather

Directory of Open Access Journals (Sweden)

Amal Amin Ibrahim

2013-01-01

Full Text Available Although chrome is considered as the major tanning agent in the production of all types of hides and leather worldwide, it represents a serious source of environmental pollution. Therefore, polyamidoamine hyperbranched polymer (HPAM was involved in pretanning of the depickled hides to enhance the chromium uptake during the tanning process. The key parameters which affect the exhaustion and fixation of chrome tan including shrinkage temperature of the tanned leather were studied. The results showed a significant improvement in the chrome exhaustion, the shrinkage temperature, and the texture and softness of the leather treated by HPAM.

Contact allergens in shoe leather among patients with foot eczema.

NARCIS (Netherlands)

Coevorden, A.M. van; Coenraads, P.J.; Pas, H.H.; Valk, P.G.M. van der

2002-01-01

Some patients with relapsing foot eczema and a shoe leather allergy, who fail to show positive results with standard series and shoe wear screening tray patch testing, do not respond to the use of hypoallergenic shoe leather. We assume that relevant allergens are present in hypoallergenic shoe

Contact allergens in shoe leather among patients with foot eczema

NARCIS (Netherlands)

van Coevorden, AM; Coenraads, PJ; Pas, HH; van der Valk, PGM

Some patients with relapsing foot eczema and a shoe leather allergy, who fail to show positive results with standard series and shoe wear screening tray patch testing, do not respond to the use of hypoallergenic shoe leather. We assume that relevant allergens are present in hypoallergenic shoe

Genotoxicity and oxidative stress in chromium-exposed tannery workers in North India.

Science.gov (United States)

Ambreen, Khushboo; Khan, Faizan Haider; Bhadauria, Smrati; Kumar, Sudhir

2014-06-01

Trivalent chromium (Cr) is an environmental contaminant, which is extensively used in tanning industries throughout the world and causes various forms of health hazards in tannery workers. Therefore, a cross-sectional study design was used to evaluate the DNA damage and oxidative stress condition in tannery workers exposed to Cr in North India. The study population comprised 100 male tanners in the exposed group and 100 healthy males (no history of Cr exposure) in the comparable control group. Baseline characteristics including age, smoking, alcohol consumption habits and duration of exposure were recorded via interviewing the subjects. Blood Cr level (measured by atomic absorption spectrophotometry), DNA damage (measured by comet assay) and oxidative stress parameters (malondialdehyde (MDA), glutathione (GSH) and superoxide dismutase (SOD)) were estimated in both the groups. As a result of statistical analysis, exposed group showed significantly higher level of Cr (p  0.05) on DNA damage and oxidative stress parameters in both the groups. In simple and multiple correlation analysis, DNA damage and oxidative stress parameters showed significant correlation with Cr level and duration of exposure in exposed group. The findings of the present study revealed that chronic occupational exposure to trivalent Cr may cause DNA damage and oxidative stress in tannery workers. © The Author(s) 2012.

Molecular spectroscopic study for suggested mechanism of chrome tanned leather

Science.gov (United States)

Nashy, Elshahat H. A.; Osman, Osama; Mahmoud, Abdel Aziz; Ibrahim, Medhat

2012-03-01

Collagen represents the structural protein of the extracellular matrix, which gives strength of hides and/or skin under tanning process. Chrome tan is the most important tanning agent all over the world. The methods for production of leather evolved over several centuries as art and engineering with little understanding of the underlying science. The present work is devoted to suggest the most probable mechanistic action of chrome tan on hide proteins. First the affect of Cr upon hide protein is indicated by the studied mechanical properties. Then the spectroscopic characterization of the hide protein as well as chrome tanned leather was carried out with Horizontal Attenuated Total Reflection (HATR) FT-IR. The obtained results indicate how the chromium can attached with the active sites of collagen. Molecular modeling confirms that chromium can react with amino as well as carboxylate groups. Four schemes were obtained to describe the possible interactions of chrome tan with hide proteins.

ON THE THERMAL BEHAVIOR OF DIFFERENT TANNED BOVINE LEATHERS

Directory of Open Access Journals (Sweden)

VARGANICI Cristian-Dragoş

2017-05-01

Full Text Available Leather is one of the most globally spread biomaterial which is obtained by the processing of different animal skins. It encompasses a wide palette of applications, from footwear and clothing to upholsteries and different types of furniture [1], [2], [3]. The main constituent of animal skins is collagen, a supramolecular fibrillar protein in the form of a triple helix. This form endows leather with elasticity, good mechanical properties and softness. A major disadvantage resides in the inapplicability of raw animal hides, due to their microbiological instability and decay through rotting. Microbiological stability is obtained through the tanning process, characterized by protein crosslinking and drying afterwards. After tanning the leather exhibits the required properties for the desired specific applications in terms of aspect, availability and sustainability [4], [5]. The study aims to elucidate the thermal decomposition process of chrome-free tanned bovine hide (wet-white using a new product based on titanium and aluminium salts compared with the same hide tanned by chromium salts (wet-blue. The thermal behavior was studied by dynamic thermogravimetry in nitrogen atmosphere, up to 700 oC. A comparative thermal decomposition study between the different tanned bovine leathers was undertaken.

Surface modification of polyester synthetic leather with tetramethylsilane by atmospheric pressure plasma

Science.gov (United States)

Kan, C. W.; Kwong, C. H.; Ng, S. P.

2015-08-01

Much works have been done on synthetic materials but scarcely on synthetic leather owing to its surface structures in terms of porosity and roughness. This paper examines the use of atmospheric pressure plasma (APP) treatment for improving the surface performance of polyester synthetic leather by use of a precursor, tetramethylsilane (TMS). Plasma deposition is regarded as an effective, simple and single-step method with low pollution. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) confirm the deposition of organosilanes on the sample's surface. The results showed that under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP treated sample with sessile drop static contact angle of 138°. The hydrophobic surface is stable without hydrophilic recovery 30 days after plasma treatment.

Environmental impacts of Sheba tannery (Ethiopia) effluents on the ...

African Journals Online (AJOL)

total chromium in drinking waters (0.05 mg/L) as opposed to the levels in the upstream waters. The increased concentrations of Cr(VI) in the water samples indicate the possible environmental pollution of the downstream water bodies by the Sheba tannery effluents. In view of the toxicity and related environmental hazards, ...

Otzi, the iceman and his leather clothes.

Science.gov (United States)

Püntener, Alois G; Moss, Serge

2010-01-01

Over 5000 years ago, a man climbed up to the icy heights of the glacier in South Tyrol, Italy and died. He was found by accident in 1991, with his clothes and equipment, mummified and frozen: an archaeological sensation and a unique snapshot of a Copper Age man. For several years highly specialised research teams have examined the mummy and all accompanying items. This paper describes how fur and leather clothes of the iceman could have been tanned. Details of the analytical tests undertaken on the 5000 year old leather samples and what they revealed are presented.

Leather in Our National Life*

Indian Academy of Sciences (India)

IAS Admin

conditions – wind, water, fire and micro-organisms; as a transmitter to feel, touch and as a sensitive ... It is resistant to wear, tear, abrasion, grease ... Skin or leather is nature's own fabric with a three dimensional matrix of interwoven collagen.

Chromium in leather footwear-risk assessment of chromium allergy and dermatitis

DEFF Research Database (Denmark)

Thyssen, Jacob P; Strandesen, Maria; Poulsen, Pia B

2012-01-01

Background. Chromium-tanned leather footwear, which releases >3 ppm hexavalent Cr(VI), may pose a risk of sensitizing and eliciting allergic dermatitis. Objectives. To determine the content and potential release of chromium in leather footwear and to discuss the prevention of chromium contact...... allergy and dermatitis. Methods. Sixty pairs of leather shoes, sandals and boots (20 children's, 20 men's, and 20 women's) were purchased in Copenhagen and examined with X-ray fluorescence spectroscopy. Chromium was extracted according to the International Standard, ISO 17075. The detection level for Cr......(VI) was 3 ppm. Results. Chromium was identified in 95% of leather footwear products, the median content being 1.7% (range 0-3.3%). No association with store category or footwear category was found. A tendency for there to be a higher chromium content in footwear with high prices was shown (p(trend) = 0...

Penelitian kulit belahan (split leather untuk barang kulit atau atasan sepatu

Directory of Open Access Journals (Sweden)

Susilowati Susilowati

1992-12-01

Full Text Available The purpose of this research is to find upper leather from splitted leather with proportional ratio of impregnating agent. The raw material used were split hide, and subjected to combination tanning process, consisted of chrome, synthetic and extract mimosa tanning agent, to get crust leather, and than were impregnated with the ratio of film forming with penetrator agent and finally they were finished with top all of the treatments fulfill/conform the requirements of SII 0018-79. There is significance difference in physical testing results.

Effect of tannery effluents on seed germination and growth of two ...

African Journals Online (AJOL)

Effect of tannery effluents on seed germination and growth of two sunflower cultivars. ... oxygen demand (COD) values along with much higher concentrations of total ... Vegetative growth parameters like plant height and number of leaves per ...

Determination of total chromium in tanned leather samples used in car industry.

Science.gov (United States)

Zeiner, Michaela; Rezić, Iva; Ujević, Darko; Steffan, Ilse

2011-03-01

Despite the high competition of synthetic fibers leather is nowadays still widely used for many applications. In order to ensure a sufficient stability of the skin matrix against many factors, such as microbial degradation, heat and sweat, a tanning process is indispensable. Using chromium (III) for this purpose offers a multitude of advantages, thus this way of tanning is widely applied. During the use of chromium tanned leather as clothing material as well as for decoration/covering purposes, chromium is extracted from the leather and may then cause nocuous effects to human skin, e.g. allergic reactions. Thus the knowledge of the total chromium content of leather samples expected to come into prolonged touch with human skin is very important. In car industry leather is used as cover for seats, steering wheel and gearshift lever The chromium contents often chromium tanned leather samples used in car industry were determined. First all samples were dried at 65 degrees C overnight and then cut in small pieces using a ceramic knife, weighed and analyzed by inductively coupled plasma--optical emission spectrometry (ICP-OES) after acidic microwave assisted digestion. The total chromium amounts found were in the range from 19 mg/g up to 32 mg/g. The extraction yield of chromium from leather samples in sweat is approximately 2-7%. Thus especially during long journeys in summer chromium can be extracted in amounts which may cause nocuous effects for example on the palm of the hands or on the back.

Removal of chromium(III) from tannery wastewater using activated carbon from sugar industrial waste.

Science.gov (United States)

Fahim, N F; Barsoum, B N; Eid, A E; Khalil, M S

2006-08-21

Chromium is commonly found in huge quantities in tannery wastewaters. For this reason, the removal and recovery of the chromium content of tannery wastewaters is crucial for environmental protection and economic reasons. Removal and recovery of chromium were carried out by using low-cost potential adsorbents. For this purpose three types of activated carbon; C1, the waste generated from sugar industry as waste products and the others (C2, C3) are commercial granular activated carbon, were used. The adsorption process and extent of adsorption are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental condition. The effect of pH, particle size and different adsorbent on the adsorption isotherm of Cr(III) was studied in batch system. The sorption data fitted well with Langmuir adsorption model. The efficiencies of activated carbon for the removal of Cr(III) were found to be 98.86, 98.6 and 93 % for C1, C2 and C3, respectively. The order of selectivity is C1>C2>C3 for removal of Cr(III) from tannery wastewater. Carbon "C1" of the highest surface area (520.66 m(2)/g) and calcium content (333.3 mg/l) has the highest adsorptive capacity for removal of Cr(III). The results revealed that the trivalent chromium is significantly adsorbed on activated carbon collected from sugar industry as waste products and the method could be used economically as an efficient technique for removal of Cr(III) and purification of tannery wastewaters.

A modified culture-based study of bacterial community composition in a tannery wastewater treatment plant.

Science.gov (United States)

Desta, Adey F; Dalhammer, Gunnel; Kittuva, Gunatrana R

2010-01-01

Though culture-independent methods have been used in preference to traditional isolation techniques for characterization of microbial community of wastewater treatment plants, it is difficult to widely apply this approach in resource-poor countries. The present study aimed to develop a test to identify the culturable portion of bacterial community in a high-strength wastewater. Wastewater samples were collected from nitrification-denitrification and settling tanks of the treatment plant of Elmo Leather AB tannery located in Borås, Sweden. After cultivating on nutrient agar with the optimal dilution (10⁻²), phenotypic and biochemical identification of the bacteria were done with colony morphology, Gram reaction, growth on MacConkey, phenylethanol media, triple sugar Iron agar slants, catalase and oxidase tests. Biochemical grouping of the isolates was done based on their test results for MacConkey, phenylethanol media, triple sugar Iron agar and oxidase test reaction. From the biochemical groups, isolates were randomly selected for API test and 16SrRNA gene sequencing. The isolates from the denitrification, nitrification tank were identified to be Paracoccus denitrificans (67%), Azoarcus spp (3%) and Spingomonas wittichii (1%). From the settling tank, Paracoccus denitrificans (22%), Corynebacterium freneyi (20%) and Bacillus cereus (1%) were identified. The grouping based on biochemical test results as well as the identification based on sequencing has shown coherence except for discrepancies with the API test. The preliminary implications of the grouping based on culture-based characteristics and its potential application for resource-limited environmental microbial studies is discussed.

89_462 - 467_BIO 062 Frouk Nas

African Journals Online (AJOL)

userpc

arrangements and less water drainages which are features that encourage persistence of the malaria vector. The area also has the popular. Coca cola food drink company and Challawa. Industrial estate which is a center point for most industries including most of the leather tanneries who create disposal wells that act as.

Leather Industry Solid Waste as Nitrogen Source for Growth of Common Bean Plants

International Nuclear Information System (INIS)

Lima, D.Q.; Oliveira, L.C.A.; Bastos, A.R.R.; Carvalho, G.S.; Marques, J.G.S.M.; Carvalho, J.G.; De Souza, G.A.

2010-01-01

The leather industry generates large amounts of a Cr-containing solid waste (wet blue leather). This material is classified by the Brazilian Environmental Council as a category-one waste, requiring a special disposal. The patented process Br n. PI 001538 is a technique to remove chromium from wet blue leather, with the recovery of a solid collagenic material (collagen), containing high nitrogen levels. This work aimed to evaluate the residual effect of soil application of collagen on the production of dry matter, content and accumulation of N in common bean plants (Phaseolus vulgaris L.), after the previous growth of elephant grass (Pennisetum purpureum Schumach.) cv. Napier, as well as to quantify the mineralization rate of N in the soil. The application of collagen, at rates equivalent to 16 and 32 tha-1, provided greater N contents in the common bean plants, indicating residual effect of these rates of application; the same was observed for the rates of 4 and 8tha-1, though in smaller proportions. Higher mineralization rates of N collagen occurred next to 16 days after soil incubation. During the 216 days of incubation, the treatments with collagen showed higher amounts of mineralized nitrogen.

Effect of tannery effluents on seed germination and growth of two ...

African Journals Online (AJOL)

TUOYO

2010-08-09

Aug 9, 2010 ... global resources, water is emerging as perhaps the most critical but ... environmental pollution as waste water effluents from tanneries are ..... As by Brassica juncea grown in a contaminated soil in Analcollar. (Spain): The ...

[Leather dust and systematic research on occupational tumors: the national and regional registry TUNS].

Science.gov (United States)

Mensi, Carolina; Sieno, Claudia; Consonni, Dario; Riboldi, Luciano

2012-01-01

The sinonasal cancer (SNC) are a rare tumors characterized by high occupational etiologic fraction. For this reason their incidence and etiology can be actively monitored by a dedicated cancer registry. The National Registry of these tumours is situated at the Italian Institute for Occupational Safety and Prevention (ISPESL) and is based on Regional Operating Centres (ROCs). In Lombardy Region the ROC has been established at the end of 2007 with the purpose to make a systematic surveillance and therefore to support in the most suitable way the scientific research and the prevention actions in the high risk working sectors. The aims of this surveillance are: to estimate the regional incidence of SNC, to define different sources of occupational and environmental exposure both known (wood, leather, nickel, chromium) and unknown. The registry collects all the new incident cases of epithelial SNC occurring in residents in Lombardy Region since 01.01.2008. The regional Registry is managed according to National Guidelines. Until January 2010 we received 596 cases of suspected SNC; only 91 (15%) of these were actually incident cases according to the inclusion criteria of the Registry, and they were preferentially adenocarcinoma and squamous carcinoma. In 2008 the regional age-standardized incidence rate of SNC for males and females, respectively, is 0.8 and 0.5 per 100,000. Occupational or environmental exposure to wood or leather dust is ascertained in over the 50% of cases. The occupational exposure to leather dust was duo to work in shoe factories. Our preliminary findings confirm that occupational exposure to wood and leather dusts are the more relevant risk factors for SNC. The study of occupational sectors and job activity in cases without such exposure could suggest new etiologic hypothesis.

Modeling of Cr contamination in the agricultural lands of three villages near the leather industry in Kasur, Pakistan, using statistical and GIS techniques.

Science.gov (United States)

Shafiq, Muhammad; Shaukat, Tahira; Nazir, Aisha; Bareen, Firdaus-E-

2017-08-01

Kasur is one of the hubs of leather industry in the Punjab, Pakistan, where chrome tanning method of leather processing is extensively being used. Chromium (Cr) accumulation levels in the irrigation water, soil, and seasonal vegetables were studied in three villages located in the vicinity of wastewater treatment plant and solid waste dumping site operated by the Kasur Tanneries Waste Management Agency (KTWMA). The data was interpreted using analysis of variance (ANOVA), clustering analysis (CA), and principal component analysis (PCA). Interpolated surface maps for Cr were generated using the actual data obtained for the 30 sampling sites in each of the three villages for irrigation water, soil, and seasonal vegetables. The level of contamination in the three villages was directly proportional to their distance from KTWMA wastewater treatment plant and the direction of water runoff. The highest level of Cr contamination in soil (mg kg -1 ) was observed at Faqeeria Wala (37.67), intermediate at Dollay Wala (30.33), and the least in Maan (25.16). A gradational variation in Cr accumulation was observed in the three villages from contaminated wastewater having the least contamination level (2.02-4.40 mg L -1 ), to soil (25.16-37.67 mg kg -1 ), and ultimately in the seasonal vegetable crops (156.67-248.33 mg kg -1 ) cultivated in the region, having the highest level of Cr contamination above the permissible limit. The model used not only predicted the current situation of Cr contamination in the three villages but also indicated the trend of magnification of Cr contamination from irrigation water to soil and to the base of the food chain. Among the multiple causes of Cr contamination of vegetables, soil irrigation with contaminated groundwater was observed to be the dominant one.

Reliability and validity of general health questionnaire (GHQ-12) for male tannery workers: a study carried out in Kanpur, India.

Science.gov (United States)

Kashyap, Gyan Chandra; Singh, Shri Kant

2017-03-21

The purpose of this study was to test the reliability, validity and factor structure of GHQ-12 questionnaire on male tannery workers of India. We have tested three different factor models of the GHQ-12. This paper used primary data obtained from a cross-sectional household study of tannery workers from Jajmau area of the city of Kanpur in northern India, which was conducted during January-June, 2015, as part of a doctoral program. The study covered 286 tannery workers from the study area. An interview schedule containing GHQ-12 was used for tannery workers who had completed at least 1 year at their present occupation preceding the survey. To test reliability, Cronbach's alpha test was used. The convergent test was used for validity. Confirmatory factor analysis was used to compare three factor structures for the GHQ-12. A total of 286 samples were analyzed in this study. The mean age of the tannery workers in this study was 38 years (SD = 1.42). We found the alpha coefficient to be 0.93 for the complete sample. The value of alpha represents the acceptable internal consistency for all the groups. Each item of scale showed almost the same internal consistency of 0.93 for the male tannery workers. The correlation between factor 1 (Anxiety and Depression) and factor 2 (Social Dysfunction) was 0.92. The correlation between factor 1 (Anxiety and Depression) and factor 3 (Loss of confidence) was the highest 0.98. Comparative fit index (CFI) estimate best-fitted for model-III that gave the CFI value 0.97. The SRMR indicator gave the lowest value 0.031 for the model-III. The findings suggest that the Hindi version of GHQ-12 is a reliable and valid tool for measuring psychological distress in male tannery workers of Kanpur city, India. Study found that the model proposed by the Graetz was the best fitted model for the data.

CHROMIUM BIOACCUMULATION FROM COMPOSTS AND VERMICOMPOSTS BASED ON TANNERY SLUDGES

Directory of Open Access Journals (Sweden)

Krzysztof GONDEK

2008-07-01

Full Text Available Storage of waste substances is not indifferent to ecological equilibrium in the environment therefore should not be the ultimate way to limit waste arduousness. Therefore, the conducted investigations aimed to determine the effect of tannery composts and vermicomposts loaded with chromium on this element bioaccumulation in earthworm bodies and biomass of selected plants. Chromium in composts and vermicomposts based on tannery sludges occurred in small quantities and easily soluble compounds. Chromium concentrations in redworm biomass points to this metal accumulation in Eisenia fetida body tissues. This element content in redworm biomass was signifi cantly positively correlated with its content in composts. Chromium content in plants was diversifi ed and on treatments was generally smaller than on mineral treatment or farmyard manure. Chromium absorbed by plants was stored mainly in the root systems, and over the norm content of this element found in vermicomposts did not cause its excessive accumulation in plant biomass.

Formation of PCDD and PCDF in the thermal treatment of footwear leather wastes.

Science.gov (United States)

Godinho, Marcelo; Marcilio, Nilson Romeu; Masotti, Leonardo; Martins, Celso Brisolara; Ritter, Diego Elias; Wenzel, Bruno München

2009-08-15

The leather waste generated by the footwear industry is considered dangerous due to the presence of trivalent chromium, derived from the salt utilized to tan hides. In Brazil, the majority of this waste is disposed on landfills and only about 3% are recycled. The thermal treatment is an alternative method for purification of such residues. By using this technique it is possible to generate energy and recover the chromium present in the ash for the production of basic chromium sulfate (tanning industry), high carbon ferrochromium or carbon-free ferrochromium (steel industry). In the last 10 years, the gasification and combustion of footwear leather waste have been intensively studied at the Federal University of Rio Grande do Sul. The research experiment for characterization of the emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) were carried out in a semi-pilot unit (350 kW(th)). From new investments the thermal capacity of the unit will increase to 600 kW(th). The unit will produce power from the heat generated in the combustion. The experimental results indicated that during the thermal treatment of footwear leather wastes, the formation mechanism of PCDD/F is the de novo synthesis. Most of PCDD/F were found in the particulate phase (>95%). A kinetic model was used for discussion of the achieved experimental results. The model is based in the carbon gasification, PCDD/F formation, desorption and degradation. From the conclusions obtained in this work will be possible minimize the PCDD/F formation in process of combustion of footwear leather wastes.

Leather Industry Business Linkages (Case Study in District Magetan

Directory of Open Access Journals (Sweden)

Dilahur Dilahur

2004-01-01

Full Text Available Leather industry in Magetan covers two forms; they are tanning and leathercraft. During 1960 and 1970, the leather industry decreased in its production, but in 1990 Magetan becomes the center of leather industry. Its development appeals to be studied closely. The goals of this study are to know the relation between tanning and leathercraft, the connection between these industries and other economic ativities, and their connection with production factor. This study uses survey methhod. The respondents are taken proportionally from both of those leather industries. The data is obtained inetrviewing the respondents with questionnaire that related to the input and out put of the industry. The result of this study shows that there is no relationship between the kind of industries (small and household industry and its capital, especially in its raw material (44,44%. The relationship between tanning and leathercraft is low, because it is only 24,2% input of leathercraft which taken from output of tanning. The region relationship for tanning is larger, because the products that are sold to other regions are 97,22% for tanning and 68,29% for leathercraft. Its relationship to other sectors especially for labour supply is 56,48% from farming and trade sectors in marketing.

Percentage Level of Tannin fur Rabbit for Leather Concerning Stitch Tearing Strength, Tearing Strength and Flexibility

Directory of Open Access Journals (Sweden)

Mustakim Mustakim

2012-02-01

Full Text Available The purpose of this study was to find out the appropriate of tannin level for rabbit fur leather concerning stitch tearing strength, tearing strength, and flexibility. The result were expected to contribute good information for the society, leather craftsman, and further researchers about fur leather tanning especially rabbit fur leather with tannin concerning stitch tearing strength, tearing strength and flexibility. The material that used were 12 pieces of four months of rabbit skin. The research method was Completely Randomized Design, consist of three treatments of tannin, they were: M1 (mimosa 15%, M2 (mimosa 20%, and M3 (mimosa 25%. Each of treatment hold on four repetition, the variables which measured were stitch tearing strength, tearing strength, and flexibility of fur leather. Data were  analysed by analysis variance followed by Duncan’s Multiple Range Test. The result of this research indicate that the use level of tannin give significant influence (P<0.05 among stitch tearing strength, tearing strength. It gave a very significant influence (P<0.01 for flexibility of rabbit fur leather. Based on the result, can be concluded that 25 % of tannin (mimosa, produce the best  result on stitch tearing strength and tearing strength. The increase of tannin offer will decrease the flexibility of fur leather but the lowest tannin produced the best flexibility of fur leather (15 percent. The best quality of rabbit fur leather produced by 25 % of tannin.   Keywords : leather, tannin, quality

Chromium(VI) release from leather and metals can be detected with a diphenylcarbazide spot test.

Science.gov (United States)

Bregnbak, David; Johansen, Jeanne D; Jellesen, Morten S; Zachariae, Claus; Thyssen, Jacob P

2015-11-01

Along with chromium, nickel and cobalt are the clinically most important metal allergens. However, unlike for nickel and cobalt, there is no validated colorimetric spot test that detects chromium. Such a test could help both clinicians and their patients with chromium dermatitis to identify culprit exposures. To evaluate the use of diphenylcarbazide (DPC) as a spot test reagent for the identification of chromium(VI) release. A colorimetric chromium(VI) spot test based on DPC was prepared and used on different items from small market surveys. The DPC spot test was able to identify chromium(VI) release at 0.5 ppm without interference from other pure metals, alloys, or leather. A market survey using the test showed no chromium(VI) release from work tools (0/100). However, chromium(VI) release from metal screws (7/60), one earring (1/50), leather shoes (4/100) and leather gloves (6/11) was observed. We found no false-positive test reactions. Confirmatory testing was performed with X-ray fluorescence (XRF) and spectrophotometrically on extraction fluids. The use of DPC as a colorimetric spot test reagent appears to be a good and valid test method for detecting the release of chromium(VI) ions from leather and metal articles. The spot test has the potential to become a valuable screening tool. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Vegetable Tannins Used in the Manufacture of Historic Leathers

OpenAIRE

Lina Falcão; Maria Eduarda M. Araújo

2018-01-01

In this review, a brief description of how animal skins were transformed in leathers in Europe using different vegetable tannins will be presented. Special attention will be dedicated to the description of the type of tannins and the characteristics of the most important type of historic leathers thus obtained. The text will also focus on the description of the techniques used in the identification of these tannins in historic objects: colorimetric tests and spectroscopic analysis.

Chrome recycling from leather solid wastes

International Nuclear Information System (INIS)

Mohamed, O.A.; Mohamady, H.S.; El-Sayed, N.H.

2005-01-01

Leather processing is one of the industrial activities that generate chromium bearing wastes in different forms, one of them is chrome shavings which contributes about 10% of the quantum raw skins /hides, and causes on burning dangerous human hazardous. Hydrolysis processes by different alkalis such as (LiOK KOH, NaOH) have been applied to recover chrome from solid wastes. The extent of hydrolysis was studied as a function of alkalis concentrations, in presence and absence of reducing agents, shaking time and temperature. Hydrolysis process exhibits 99%, 98% and 97%, chrome recovery for LiOH, KOH and NaOH respectively. The recovered chrome has been used in retaining process, examined through visual and mechanical tests of leather samples. The evaluation of the tanning process with recovered chrome gave acceptable results

Chromium(III) release from chromium‐tanned leather elicits allergic contact dermatitis: a use test study

Science.gov (United States)

Erfani, Behnaz; Matura, Mihály; Lidén, Carola

2018-01-01

Summary Background Chromium (Cr) is a common skin sensitizer. The use of Cr(VI) in leather is restricted in the EU, but that of Cr(III) is not. Objectives To assess whether prolonged exposure to Cr‐tanned leather with mainly Cr(III) release may elicit allergic contact dermatitis in Cr‐allergic individuals. Method Ten Cr‐allergic subjects and 22 controls were patch tested with serial dilutions of Cr(III) and Cr(VI), and with leather samples. They then conducted a use test with a Cr‐tanned and a Cr‐free leather bracelet over a period of 3 weeks, for 12 h per day. Cr deposited on the skin from the bracelets was measured in the controls, and the diphenylcarbazide test for Cr(VI) and extraction tests for Cr(III) and Cr(VI) were conducted for the different leathers. Results Four of 10 Cr‐allergic subjects developed positive reactions to the Cr‐tanned bracelet within 7–21 days, whereas only 1 of 10 had a positive patch test reaction to this leather. Cr released from the Cr‐tanned leather was most probably entirely Cr(III), with a quantifiable amount being deposited on the skin. Conclusions This study strongly suggests that prolonged and repeated exposure to Cr‐tanned leather with mainly Cr(III) release is capable of eliciting allergic contact dermatitis in Cr‐allergic individuals. PMID:29322530

Biointervention makes leather processing greener: an integrated cleansing and tanning system.

Science.gov (United States)

Thanikaivelan, Palanisamy; Rao, Jonnalagadda Raghava; Nair, Balachandran Unni; Ramasami, Thirumalachari

2003-06-01

The do-undo methods adopted in conventional leather processing generate huge amounts of pollutants. In other words, conventional methods employed in leather processing subject the skin/hide to wide variations in pH. Pretanning and tanning processes alone contribute more than 90% of the total pollution from leather processing. Included in this is a great deal of solid wastes such as lime and chrome sludge. In the approach described here, the hair and flesh removal as well as fiber opening have been achieved using biocatalysts at pH 8.0 for cow hides. This was followed by a pickle-free chrome tanning, which does not require a basification step. Hence, this tanning technique involves primarily three steps, namely, dehairing, fiber opening, and tanning. It has been found that the extent of hair removal, opening up of fiber bundles, and penetration and distribution of chromium are comparable to that produced by traditional methods. This has been substantiated through scanning electron microscopic, stratigraphic chrome distribution analysis, and softness measurements. Performance of the leathers is shown to be on par with conventionally processed leathers through physical and hand evaluation. Importantly, softness of the leathers is numerically proven to be comparable with that of control. The process also demonstrates reduction in chemical oxygen demand load by 80%, total solids load by 85%, and chromium load by 80% as compared to the conventional process, thereby leading toward zero discharge. The input-output audit shows that the biocatalytic three-step tanning process employs a very low amount of chemicals, thereby reducing the discharge by 90% as compared to the conventional multistep processing. Furthermore, it is also demonstrated that the process is technoeconomically viable.

Valorization of titanium metal wastes as tanning agent used in leather industry

Energy Technology Data Exchange (ETDEWEB)

Crudu, Marian, E-mail: mariancrudu@yahoo.com [The National Research and Development Institute for Textiles and Leather – Division Leather and Footwear Research Institute, 93 Ion Minulescu Str., Bucharest (Romania); Deselnicu, Viorica, E-mail: viorica.deselnicu@icpi.ro [The National Research and Development Institute for Textiles and Leather – Division Leather and Footwear Research Institute, 93 Ion Minulescu Str., Bucharest (Romania); Deselnicu, Dana Corina, E-mail: d_deselnicu@yahoo.com [University Politehnica Bucharest, Splaiul Independentei Nr. 313, Sector 6, RO-060042 Bucharest (Romania); Albu, Luminita, E-mail: luminita.albu@gmail.com [The National Research and Development Institute for Textiles and Leather – Division Leather and Footwear Research Institute, 93 Ion Minulescu Str., Bucharest (Romania)

2014-10-15

Highlights: • Valorization of titanium wastes which cannot be recycled in metallurgical industry. • Transferring Ti waste into raw materials for obtaining Ti based tanning agent. • Characterization of new Ti based tanning agents and leather tanned with them. • Characterization of sewage waste water and sludge resulted from leather manufacture. • Analysis of the impact of main metal component of Ti waste. - Abstract: The development of new tanning agents and new technologies in the leather sector is required to cope with the increasingly higher environmental pressure on the current tanning materials and processes such as tanning with chromium salts. In this paper, the use of titanium wastes (cuttings) resulting from the process of obtaining highly pure titanium (ingots), for the synthesis of new tanning agent and tanning bovine hides with new tanning agent, as alternative to tanning with chromium salts are investigated. For this purpose, Ti waste and Ti-based tanning agent were characterized for metal content by inductively coupled plasma mass spectrometry (ICP-MS) and chemical analysis; the tanned leather (wet white leather) was characterized by Scanning Electron Microscope/Energy Dispersive Using X-ray (Analysis). SEM/EDX analysis for metal content; Differential scanning calorimetric (DSC), Micro-Hot-Table and standard shrinkage temperature showing a hydrothermal stability (ranged from 75.3 to 77 °C) and chemical analysis showing the leather is tanned and can be processed through the subsequent mechanical operations (splitting, shaving). On the other hand, an analysis of major minor trace substances from Ti-end waste (especially vanadium content) in new tanning agent and wet white leather (not detected) and residue stream was performed and showed that leachability of vanadium is acceptable. The results obtained show that new tanning agent obtained from Ti end waste can be used for tanning bovine hides, as eco-friendly alternative for chrome tanning.

Valorization of titanium metal wastes as tanning agent used in leather industry

International Nuclear Information System (INIS)

Crudu, Marian; Deselnicu, Viorica; Deselnicu, Dana Corina; Albu, Luminita

2014-01-01

Highlights: • Valorization of titanium wastes which cannot be recycled in metallurgical industry. • Transferring Ti waste into raw materials for obtaining Ti based tanning agent. • Characterization of new Ti based tanning agents and leather tanned with them. • Characterization of sewage waste water and sludge resulted from leather manufacture. • Analysis of the impact of main metal component of Ti waste. - Abstract: The development of new tanning agents and new technologies in the leather sector is required to cope with the increasingly higher environmental pressure on the current tanning materials and processes such as tanning with chromium salts. In this paper, the use of titanium wastes (cuttings) resulting from the process of obtaining highly pure titanium (ingots), for the synthesis of new tanning agent and tanning bovine hides with new tanning agent, as alternative to tanning with chromium salts are investigated. For this purpose, Ti waste and Ti-based tanning agent were characterized for metal content by inductively coupled plasma mass spectrometry (ICP-MS) and chemical analysis; the tanned leather (wet white leather) was characterized by Scanning Electron Microscope/Energy Dispersive Using X-ray (Analysis). SEM/EDX analysis for metal content; Differential scanning calorimetric (DSC), Micro-Hot-Table and standard shrinkage temperature showing a hydrothermal stability (ranged from 75.3 to 77 °C) and chemical analysis showing the leather is tanned and can be processed through the subsequent mechanical operations (splitting, shaving). On the other hand, an analysis of major minor trace substances from Ti-end waste (especially vanadium content) in new tanning agent and wet white leather (not detected) and residue stream was performed and showed that leachability of vanadium is acceptable. The results obtained show that new tanning agent obtained from Ti end waste can be used for tanning bovine hides, as eco-friendly alternative for chrome tanning

Methodology to implement an example of social responsibility business (SRB) in the leather industry in Colombia

OpenAIRE

Vásquez Paniagua, José Alfredo; Gonzales Isaza, Diana Patricia

2012-01-01

Tannery industry is a big water resources pollutant in Colombia. By this, a bigger environmental responsibility has onwaters resources pollution in the country. This paper presents a methodological proposal to implement a CorporateSocial Responsibility methodology for Colombian Tannery Industry. In this case, Donna Wood’s theory, environmentalimpact, economic valuation of environmental quality, and citizen participation are used. La preocupación por el deterioro del medio ambiente es uno d...

Vegetable Tannins Used in the Manufacture of Historic Leathers

Directory of Open Access Journals (Sweden)

Lina Falcão

2018-05-01

Full Text Available In this review, a brief description of how animal skins were transformed in leathers in Europe using different vegetable tannins will be presented. Special attention will be dedicated to the description of the type of tannins and the characteristics of the most important type of historic leathers thus obtained. The text will also focus on the description of the techniques used in the identification of these tannins in historic objects: colorimetric tests and spectroscopic analysis.

A comprehensive evaluation of physical and environmental performances for wet-white leather manufacture

OpenAIRE

Shi, Jiabo; Puig Vidal, Rita; Sang, Jun; Lin, Wei

2016-01-01

This paper presents the comprehensive evaluation results of physical and environmental performances for a novel wet-white (chrome-free) leather manufacturing. The tanning process is optimized as 15 wt% tannic acid (TA) combination with 4 wt% Laponite nanoclay, giving the leather with shrinkage temperature (Ts) above 86 °C. Inductively coupled plasma-atomic emission spectrometry (ICP-AES) measurements indicate that Laponite can be evenly and tightly bound within the leather matrix, which is fu...

Phycoremediation of Tannery Wastewater Using Microalgae Scenedesmus Species.

Science.gov (United States)

Ajayan, Kayil Veedu; Selvaraju, Muthusamy; Unnikannan, Pachikaran; Sruthi, Palliyath

2015-01-01

A number of microalgae species are efficient in removing toxicants from wastewater. Many of these potential species are a promising, eco-friendly, and sustainable option for tertiary wastewater treatment with a possible advantage of improving the economics of microalgae cultivation for biofuel production. The present study deals with the phycoremediation of tannery wastewater (TWW) using Scenedesmus sp. isolated from a local habitat. The test species was grown in TWW under laboratory conditions and harvested on the 12th day. The results revealed that the algal biomass during the growth period not only reduced the pollution load of heavy metals (Cr-81.2-96%, Cu-73.2-98%, Pb-75-98% and Zn-65-98%) but also the nutrients (NO3 >44.3% and PO4 >95%). Fourier Transform Infrared (FTIR) spectrums of Scenedesmus sp. biomass revealed the involvement of hydroxyl amino, carboxylic and carbonyl groups. The scanning electron micrograph (SEM) and Energy Dispersive X-ray Spectroscopic analysis (EDS) revealed the surface texture, morphology and element distribution of the biosorbent. Furthermore, the wastewater generated during wet-blue tanning process can support dense population of Scenedesmus sp., making it a potential growth medium for biomass production of the test alga for phycoremediation of toxicants in tannery wastewaters.

Growth responses and metal accumulation capabilities of woody plants during the phytoremediation of tannery sludge.

Science.gov (United States)

Shukla, O P; Juwarkar, Asha A; Singh, S K; Khan, Shoeb; Rai, U N

2011-01-01

Five woody plants species (i.e. Terminalia arjuna, Prosopis juliflora, Populus alba, Eucalyptus tereticornis and Dendrocalamus strictus) were selected for phytoremediation and grow on tannery sludge dumps of Common Effluent Treatment Plant (CETP), Unnao (Uttar Pradesh), India. Concentration of toxic metals were observed high in the raw tannery sludge i.e. Fe-1667>Cr-628>Zn-592>Pb-427>Cu-354>Mn-210>Cd-125>Ni-76 mg kg(-1) dw, respectively. Besides, physico-chemical properties of the raw sludge represented the toxic nature to human health and may pose numerous risks to local environment. The growth performances of woody plants were assessed in terms of various growth parameters such as height, diameter at breast height (DBH) and canopy area of plants. All the plant species have the capabilities to accumulate substantial amount of toxic metals in their tissues during the remediation. The ratio of accumulated metals in the plants were found in the order Fe>Cr>Mn>Pb>Zn>Cu>Cd>Ni and significant changes in physico-chemical parameters of tannery sludge were observed after treatment. All the woody plants indicated high bioconcentration factor for different metals in the order Fe>Cr>Mn>Ni>Cd>Pb>Zn>Cu. After one year of phytoremediation, the level of toxic metals were removed from tannery sludge up to Cr (70.22)%, Ni (59.21)%, Cd (58.4)%, Fe (49.75)%, Mn (30.95)%, Zn (22.80)%, Cu (20.46)% and Pb (14.05)%, respectively. Copyright © 2010 Elsevier Ltd. All rights reserved.

Electrochemical oxidation of synthetic tannery wastewater in chloride-free aqueous media

International Nuclear Information System (INIS)

Costa, Carla Regina; Montilla, Francisco; Morallon, Emilia; Olivi, Paulo

2010-01-01

The electrochemical treatment of a synthetic tannery wastewater, prepared with several compounds used by finishing tanneries, was studied in chloride-free media. Boron-doped diamond (Si/BDD), antimony-doped tin dioxide (Ti/SnO 2 -Sb), and iridium-antimony-doped tin dioxide (Ti/SnO 2 -Sb-Ir) were evaluated as anode. The influence of pH and current density on the treatment was assessed by means of the parameters used to measure the level of organic contaminants in the wastewater; i.e., total phenols, chemical oxygen demand (COD), total organic carbon (TOC), and absorbance. Results showed that faster decrease in these parameters occurred when the Si/BDD anode was used. Good results were obtained with the Ti/SnO 2 -Sb anode, but its complete deactivation was reached after 4 h of electrolysis at 25 mA cm -2 , indicating that the service life of this electrode is short. The Ti/SnO 2 -Sb-Ir anode is chemically and electrochemically more stable than the Ti/SnO 2 -Sb anode, but it is not suitable for the electrochemical treatment under the studied conditions. No significant changes were observed for electrolyses performed at different pH conditions with Si/BDD, and this electrode led to almost complete mineralization after 4 h of electrolysis at 100 mA cm -2 . The increase in current density resulted in faster wastewater oxidation, with lower current efficiency and higher energy consumption. Si/BBD proved to be the best electrodic material for the direct electrooxidation of tannery wastewaters.

EXPERIMENTAL RESEARCH REGARDING LEATHER APPLICATIONS IN PRODUCT DESIGN

Directory of Open Access Journals (Sweden)

PRALEA Jeni

2015-05-01

Full Text Available This paper presents the role and importance of experimental research in design activity. The designer, as a researcher and a project manager, proposes to establish a relationship between functional-aesthetic-constructive-technological-economic,based on the aesthetic possibilities of the materials used for the experiments. With the aim to identify areas for the application of leather waste resulted from the production process, the paper presents experiments conducted with this material in combination with wood, by using different techniques that lead to different aesthetic effects. Identifying the areas to use and creating products from leather and/or wood waste, is based on the properties of these materials. Leather, the subject of these experiments, has the advantage that it can be used on both sides. Tactile differences of the two sides of this material has both aesthetical and functional advantages, which makes it suitable for applications on products that meet the requirements of "design for all". With differentiated tactile characteristics, in combination with other materials, for these experiments wood, easily "read touch" products can be generated to help people with certain disabilities. Thus, experiments presented in this paper allows the establishment of aesthetic schemes applicable to products that are friendly both with the environment (based on the reuse of wood and leather waste and with the users (can be used as applications, accessories and concepts of products for people with certain disabilities. The designer’s choices or decisions can be based on the results of this experiment. The experiment enables the designer to develop creative, innovative and environmentally friendly products.

STRUCTURAL ANALYSIS OF WOOD-LEATHER PANELS BY RAMAN SPECTROSCOPY

Directory of Open Access Journals (Sweden)

Tilman Grünewald,

2012-02-01

Full Text Available Besides other ligno-cellulosic materials such as straw, rice husks, or bagasse, wet blue particles from leather production are a promising new raw material stock for wood-based panels, as they offer not only a high availability, but increase the properties of the panel with regard to fire resistance or mechanical characteristics. A panel with a mixture of 42.5% wood fibers, 42.5% wet blue leather particles, and 15% lignin adhesive was produced, and an inhomogeneous sample was prepared. An area of 9 x 10 mm was rasterized and scanned by means of Raman Spectroscopy. Furthermore, the reference spectra of the constituents, i.e. wood fiber, wet blue leather particle, and lignin powder were recorded. The obtained data were treated and analyzed using chemometric methods (principal components analysis PCA and cluster analysis. An important finding was that the reference data were not directly represented in the panels’ spectra, and the correlation matrix of the PCA was not applicable to the panel data. This indicated that chemical changes might take place during the pressing. After processing the panel Raman spectra with the help of PCA and cluster analysis, three distinctive clusters were obtained, discriminating wood, leather, and mixed regions. With the assigned spectral information, it was possible to create a spectral image of the surface.

A note on the utilisation of the water hyacinth (eichhornia crassipes) for the treatment of tannery effluents

International Nuclear Information System (INIS)

1981-01-01

Water hyacinth is an aquatic weed which grows quickly in ponds, ditches and streams. It clogs drains, irrigation canals and run-off streams promoting back waters and flood conditions. By its prolific growth it competes with other aquatic weeds and causes destruction of the ecosystems of inland waters. Other damaging effects of water hyacinth include incubation of insects and disease vectors, hindrance to navigation, interference with fishing, increased loss of water by plant transpiration, restriction of desirable aquatic plant growth, depletion of oxygen in water and destruction of recreation values of inland waters. It has been observed from the literature that world-wide attempts have been made to destroy water hyacinth for the reasons enumerated above. But recently emphasis has been given to its utilisation rather than its destruction. Reports are available on its use in paper and pulp industries, for production of biogas, as a food for animals and as fertilizer. Water hyacinth has been used in oxidation ponds for the treatment of digested sugar wastes and effluents of septic tanks, but no work has been reported as yet on use of water hyacinth in the treatment of tannery effluents. The waste water from a tannery is highly coloured with a foul odour and contains toxic materials like phenols, sulphides and chromium in addition to bio-degradable matter like proteins, flesh, hair, etc. The untreated effluents when let into streams deplete the dissolved oxygen of the stream and destroy the aquatic life. Similarly, when the untreated effluents are let off into sewers they choke the sewers, or when let off on land they cause ground water pollution. The conventional methods of treatment of sewage, namely the trickling filter activated sludge process are equally applicable for the treatment of tannery waste water. But these methods are known to be costly both in construction and maintenance. Certain low-cost waste treatment methods have been developed involving the use

Efficient photocatalytic degradation of gaseous N,N-dimethylformamide in tannery waste gas using doubly open-ended Ag/TiO2 nanotube array membranes

Science.gov (United States)

Zhao, Yang; Ma, Lin; Chang, Wenkai; Huang, Zhiding; Feng, Xugen; Qi, Xiaoxia; Li, Zenghe

2018-06-01

Gaseous N,N-dimethylformamide (DMF), typical volatile organic compound exhausted from manufacturing factories, may damage the health of workers under long-term exposure even at low levels. The defined geometry, porous surface and highly ordered channels make the free-standing anodic TiO2 nanotube (TiNT) arrays particularly suitable for applications of practical air purification by flow-through photocatalysis. In the present work, crystallized doubly open-ended Ag/TiNT array membranes were designed and prepared by employing a lift-off process based on an anodization-annealing-anodization-etching sequence, followed by uniform Ag nanoparticles decoration. For the photocatalytic degradation of gaseous DMF at low concentration levels close to that found in realistic pollutant air, an analytical methodology for the monitoring and determination of degradation process was developed based on the coupling of headspace sampling with gas chromatography mass spectrometry (HS-GC-MS). The doubly open-ended Ag/TiNT arrays exhibited higher removal efficiency of gaseous DMF from air compared with conventional bottom-closed Ag/TiNT arrays and pure bottomless TiNT arrays. These results indicated that the photocatalytic properties of TiNT arrays were improved with the open-bottom morphology and the Ag nanoparticles decoration. Based on the analysis with GC-MS and high performance ion chromatography (HPIC), it was found that demethylation is the main pathway of DMF degradation in photocatalytic reactions. Furthermore, decontamination of actual polluted tannery waste gas collected in leather factory proved that the photocatalysis on doubly open-ended Ag/TiNT array membrane is an efficient way and a promising application to treat air contaminated by DMF despite the complexity of various volatile organic compounds.

Percentage Level of Tannin fur Rabbit for Leather Concerning Stitch Tearing Strength, Tearing Strength and Flexibility

OpenAIRE

Mustakim Mustakim; Aris Sri Widati; Lisa Purnaningtyas

2012-01-01

The purpose of this study was to find out the appropriate of tannin level for rabbit fur leather concerning stitch tearing strength, tearing strength, and flexibility. The result were expected to contribute good information for the society, leather craftsman, and further researchers about fur leather tanning especially rabbit fur leather with tannin concerning stitch tearing strength, tearing strength and flexibility. The material that used were 12 pieces of four months of rabbit skin. The re...

Effect of Storage on the Physico-Chemical and Antioxidant Properties of Strawberry and Kiwi Leathers.

Science.gov (United States)

Concha-Meyer, Anibal A; D'Ignoti, Valeria; Saez, Barbara; Diaz, Ricardo I; Torres, Carolina A

2016-03-01

Strawberry and kiwi leathers were used to develop a new healthy and preservative-free fruit snack for new markets. Fruit puree was dehydrated at 60 °C for 20 h and subjected to accelerated storage. Soluble solids, titratable acidity, pH, water activity (aw ), total phenolic (TP), antioxidant activity (AOA) and capacity (ORAC), and color change (browning index) were measured in leathers, cooked, and fresh purees. An untrained panel was used to evaluate consumer acceptability. Soluble solids of fresh purees were 11.24 to 13.04 °Brix, whereas pH was 3.46 to 3.39. Leathers presented an aw of 0.59 to 0.67, and a moisture content of 21 kg water/100 kg. BI decreased in both leathers over accelerated storage period. TP and AOA were higher (P ≤ 0.05) in strawberry formulations. ORAC decreased 57% in strawberry and 65% in kiwi leathers when compared to fruit puree. TP and AOA increased in strawberries during storage. Strawberry and Kiwi leathers may be a feasible new, natural, high antioxidant, and healthy snack for the Chilean and other world markets, such as Europe, particularly the strawberry leather, which was preferred by untrained panelists. © 2016 Institute of Food Technologists®

Buffing dust as a filler of carboxylated butadiene-acrylonitrile rubber and butadiene-acrylonitrile rubber.

Science.gov (United States)

Chronska, K; Przepiorkowska, A

2008-03-01

Buffing dust from chrome tanned leather is one of the difficult tannery wastes to manage. It is also hazardous to both human health and the environment. The scientific literature rarely reports studies on dust management, especially on its utilization as a filler for elastomers. In this connection we have made an attempt to use this leather waste as a filler for rubbers such as XNBR and NBR. The addition of the buffing dust to rubber mixes brought improvement in mechanical properties, and increase in resistance to thermal ageing as well as in electric conductivity and crosslink density of vulcalizates.

Toxic effects of chromic sulphate on the common carp, Cyprinus carpio

Energy Technology Data Exchange (ETDEWEB)

Wong, M.H.; Lau, W.M.; Tong, T.Y.; Liu, W.K.; Luk, K.C.

1982-02-01

The effects of chromic sulphate, which is commonly used in the tanning of leather, on the common carp, Cyprinus carpio and the bighead, Aristichthys nobilis, were studied. C. carpio was found to be more susceptible than A. nobilis to chromic sulphate at the lowest concentration tested (100 mg/l) whereas results obtained at other concentration were similar for both species. Damage to the gills, liver and intestine was observed by histopathological examination. A wide range of chemicals is used in the different stages of treating leather and a possible treatment of the effluent from the tanneries is suggested.

A DSC investigation on the changes in pore structure of skin during leather processing

International Nuclear Information System (INIS)

Fathima, N. Nishad; Kumar, M. Pradeep; Rao, J. Raghava; Nair, B.U.

2010-01-01

Leather processing involves many unit operations that modify the physical, chemical and biological properties of the raw skin/hide of an animal. One such major variation is brought to pore structure and size, which determines the breathing property of skin. Understanding this property is essential to improve the end use of the leather matrix. Thermoporometric technique has been used in this study to bring out the influence of various process steps on the pore size distribution of skin. Marked changes in the depression of freezing point are observed for each process. Scanning electron microscopy study reveals the morphological changes in the grain and cross-section of the skin during leather processing. Understanding and predictions of pore structure changes at various stages of leather processing would benefit: (a) in process control, (b) analysis of cost benefit ratio and (c) strategic planning and transport. Thus, this study aids in better understanding of the pore structure of skin to improve the functional properties of the leather.

TANNED LEATHERS PROPERTIES MODIFICATION AS A RESULT OF ARTIFICIAL AGEING

Directory of Open Access Journals (Sweden)

ROŞU Dan

2017-05-01

Full Text Available Leather is a high tech material with different application fields, such as automotive, manufacturing of leatherwear articles or clothing and footwear. Leather is a biomaterial obtained by processing animal skins. Unfortunately, raw animal hides are practically inutilizable, due to their microbiological instability and are affected by rotting. Microbiological stability is achieved by tanning, when the protein is crosslinked, followed by drying. After crosslinking and drying, the new material shows the required properties of sustainability, availability and an esthetically pleasing aspect to the touch, making it available across its entire range of applications. From a structural point of view the animal skins are constituted of collagen, which is a fibrilar protein with a high degree of supramolecular organization in triple helix form that endows softness, elasticity and mechanical strength. High quality standards and lack of toxicity are required in all cases. Leather colour changes during exposure to light radiations are considered a consequence of the presence of some products with weak photochemical resistance during fabrication. The study aims to compare changes in properties of leathers obtained using mineral tanning agents such as Cr III salts and those obtained with the more environment-friendly technology using acid hydrolysis. Accelerated aging studies were conducted on tanned leathers by exposing the samples to UV radiation with different irradiation doses and two wavelengths (254 and 365 nm under controlled humidity and temperature conditions. Structural changes caused by irradiation were studied by FTIR. Colour changes on the sample surfaces were assessed during irradiation with the CIEL a*b* system. The colour parameters variation (L*, a*, b* and colour differences have been discussed in correlation with structural changes, tanning method and irradiation conditions.

A STUDY ON USING 3D VISUALIZATION AND SIMULATION PROGRAM (OPTITEX 3D ON LEATHER APPAREL

Directory of Open Access Journals (Sweden)

Ork Nilay

2016-05-01

Full Text Available Leather is a luxury garment. Design, material, labor, fitting and time costs are very effective on the production cost of the consumer leather good. 3D visualization and simulation programs which are getting popular in textile industry can be used for material, labor and time saving in leather apparel. However these programs have a very limited use in leather industry because leather material databases are not sufficient as in textile industry. In this research, firstly material properties of leather and textile fabric were determined by using both textile and leather physical test methods, and interpreted and introduced in the program. Detailed measures of an experimental human body were measured from a 3D body scanner. An avatar was designed according to these measurements. Then a prototype dress was made by using Computer Aided Design-CAD program for designing the patterns. After the pattern making, OptiTex 3D visualization and simulation program was used to visualize and simulate the dresses. Additionally the leather and cotton fabric dresses were sewn in real life. Then the visual and real life dresses were compared and discussed. 3D virtual prototyping seems a promising potential in future manufacturing technologies by evaluating the fitting of garments in a simple and quick way, filling the gap between 3D pattern design and manufacturing, providing virtual demonstrations to customers.

Association between cobalt allergy and dermatitis caused by leather articles

DEFF Research Database (Denmark)

Bregnbak, David; Thyssen, Jacob P; Zachariae, Claus

2015-01-01

BACKGROUND: Cobalt is a strong skin sensitizer and a prevalent contact allergen. Recent studies have recognized exposure to leather articles as a potential cause of cobalt allergy. OBJECTIVES: To examine the association between contact allergy to cobalt and a history of dermatitis resulting from...... exposure to leather. METHODS: A questionnaire case-control study was performed: the case group consisted of 183 dermatitis patients with a positive patch test reaction to cobalt chloride and a negative patch test reaction to potassium dichromate; the control group consisted of 621 dermatitis patients who...... did not react to either cobalt or chromium in patch testing. Comparisons were made by use of a χ(2) -test, Fisher's exact, and the Mann-Whitney test. Logistic regression analyses were used to test for associations while taking confounding factors into consideration. RESULTS: Leather was observed...

Electrochemical treatment of evaporated residue of soak liquor generated from leather industry

International Nuclear Information System (INIS)

Boopathy, R.; Sekaran, G.

2013-01-01

Highlights: • Electrochemical treatment of evaporated residue of soak liquor (ERSL) generated in Tannery. • Copper coating on electrode surface and horizontal mounting of electrodes for ERSL treatment. • Electrochemical oxidation of organic pollutants under high saline condition. • The treated solution may be evaporated to dryness to get NaCl salt for hide/skin preservation. -- Abstract: The organic and suspended solids present in soak liquor, generated from leather industry, demands treatment. The soak liquor is being segregated and evaporated in solar evaporation pans/multiple effect evaporator due to non availability of viable technology for its treatment. The residue left behind in the pans/evaporator does not carry any reuse value and also faces disposal threat due to the presence of high concentration of sodium chloride, organic and bacterial impurities. In the present investigation, the aqueous evaporated residue of soak liquor (ERSL) was treated by electrochemical oxidation. Graphite/graphite and SS304/graphite systems were used in electrochemical oxidation of organics in ERSL. Among these, graphite/graphite system was found to be effective over SS304/graphite system. Hence, the optimised conditions for the electrochemical oxidation of organics in ERSL using graphite/graphite system was evaluated by response surface methodology (RSM). The mass transport coefficient (k m ) was calculated based on pseudo-first order rate kinetics for both the electrode systems (graphite/graphite and SS304/graphite). The thermodynamic properties illustrated the electrochemical oxidation was exothermic and non-spontaneous in nature. The calculated specific energy consumption at the optimum current density of 50 mA cm −2 was 0.41 kWh m −3 for the removal of COD and 2.57 kWh m −3 for the removal of TKN

ACCEPTANCE OF FUNCTIONAL FOOD AMONG CHILEAN CONSUMERS: APPLE LEATHER.

Science.gov (United States)

van Vliet, Maya; Adasme-Berrios, Cristian; Schnettler, Berta

2015-10-01

the aim of this study is to measure acceptance of a specific functional food: apple (fruit) leather, based on organoleptic characteristics and to identify consumer types and preferences for natural additives which increase the product's functionality and meet current nutritional needs. a sample of 800 consumers provided an evaluation of apple leather in terms of acceptance (liking). A sensorial panel was carried out using a 9-point hedonic scale. Cluster analysis was used to identify different acceptance-based consumer types. In addition, a conjoint analysis was carried out to determine preference for different additives. the cluster analysis resulted in four groups with significant differences in the average likings obtained from the sensory panel. Results indicate that the sweetness of the tested apple leather was evaluated best among all groups and, on average, color was rated as the worst attribute. However, overall likings differ significantly between groups. Results from the conjoint analysis indicate that, in general, consumers prefer natural additives included in the product which enhance functionality. although there is a "global acceptance" of the product, there are significant differences between groups. The results of the conjoint analysis indicate that, in general, consumers prefer the aggregation of natural additives which increase the product's functionality. Apple leather with natural additives, such as anticariogenics and antioxidants, can be considered a functional substitute of unhealthy snacks and/or sweets. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Using of Hyperbranched Poly(amidoamine) as Pretanning Agent for Leather

OpenAIRE

Ibrahim, Amal Amin; Youssef, Moshera S. A.; Nashy, El-Shahat H. A.; Eissa, Mohamed M.

2013-01-01

Although chrome is considered as the major tanning agent in the production of all types of hides and leather worldwide, it represents a serious source of environmental pollution. Therefore, polyamidoamine hyperbranched polymer (HPAM) was involved in pretanning of the depickled hides to enhance the chromium uptake during the tanning process. The key parameters which affect the exhaustion and fixation of chrome tan including shrinkage temperature of the tanned leather were studied. The results ...

Multivariate analysis of selected metals in tannery effluents and related soil.

Science.gov (United States)

Tariq, Saadia R; Shah, Munir H; Shaheen, N; Khalique, A; Manzoor, S; Jaffar, M

2005-06-30

Effluent and relevant soil samples from 38 tanning units housed in Kasur, Pakistan, were obtained for metal analysis by flame atomic absorption spectrophotometric method. The levels of 12 metals, Na, Ca, K, Mg, Fe, Mn, Cr, Co, Cd, Ni, Pb and Zn were determined in the two media. The data were evaluated towards metal distribution and metal-to-metal correlations. The study evidenced enhanced levels of Cr (391, 16.7 mg/L) and Na (25,519, 9369 mg/L) in tannery effluents and relevant soil samples, respectively. The effluent versus soil trace metal content relationship confirmed that the effluent Cr was strongly correlated with soil Cr. For metal source identification the techniques of principal component analysis, and cluster analysis were applied. The principal component analysis yielded two factors for effluents: factor 1 (49.6% variance) showed significant loading for Ca, Fe, Mn, Cr, Cd, Ni, Pb and Zn, referring to a tanning related source for these metals, and factor 2 (12.6% variance) with higher loadings of Na, K, Mg and Co, was associated with the processes during the skin/hide treatment. Similarly, two factors with a cumulative variance of 34.8% were obtained for soil samples: factor 1 manifested the contribution from Mg, Mn, Co, Cd, Ni and Pb, which though soil-based is basically effluent-derived, while factor 2 was found associated with Na, K, Ca, Cr and Zn which referred to a tannery-based source. The dendograms obtained from cluster analysis, also support the observed results. The study exhibits a gross pollution of soils with Cr at levels far exceeding the stipulated safe limit laid down for tannery effluents.

Chromed Leather Dyeing Peculiarities when Deliming with Peracetic Acid

OpenAIRE

Kęstutis BELEŠKA; Virgilijus VALEIKA; Justa ŠIRVAITYTĖ; Violeta VALEIKIENĖ

2013-01-01

The research was aimed to investigate the influence of deliming with peracetic acid on leather dyeing kinetics. Hydrophobic C.I. Acid Red 213 and hydrophilic C.I. Acid Red 423 dyes were used. Sorption of dye depends on hydrophobicity/hydrophility of dye and dyeing temperature. Equilibrium of process is reached faster using hydrophobic C.I. Acid Red 213 at 45 ºC. However, both control and experimental leather fibres adsorb more hydrophilic dye C.I. Acid Red 423 and this fact does not depend on...

Characterization of Briquette Produced from Tannery Solid Waste

Directory of Open Access Journals (Sweden)

Olatunde Ajani Oyelaran

2017-06-01

Full Text Available Skin processing produces large volumes of wastes, much of which are not utilized but disposed in the landfill. This study explored the possibility of producing briquettes from tannery waste that could be used for heating purposes for cottage factories and domestic cooking. Wastes studied are buffing dust, chrome shavings, fleshing, and hair. The briquette properties tested were moisture content, volatile matter, ash content, fixed carbon content, calorific value, compressive strength, density and durability. The moisture content of the raw materials ranged between 2.04 and 8.37% while the moisture content of the produced briquettes after 19 days of drying ranges between 1.17 and 4.13%. The volatile matter also decreases while the ash content increases after briquetting. The fixed carbon content ranges 73.79 and 93.23%. The heating values of the briquettes also showed a great increased after briquetting of between 19.82 and 21.86 MJ/kg. The compressive strength ranges between 0.17 and 0.21 kN/cm2, the durability ranges between 97.83 and 99.54%. The maximum densities of the briquettes also meet the required specifications of minimum value of 600 kg/m3. The briquettes produced also possess good qualities that make tannery solid waste a materials for production of briquettes for heating and in cottage industries

Toxicity of high salinity tannery wastewater and effects on constructed wetland plants

DEFF Research Database (Denmark)

Calheirosa, C.S.C.; Silva, G.; Quitério, P.V.B.

2012-01-01

The toxicity of high salinity tannery wastewater produced after an activated sludge secondary treatment on the germination and seedling growth of Trifolium pratense, a species used as indicator in toxicity tests, was evaluated. Growth was inhibited by wastewater concentrations >25% and undiluted ...

The Role of ISO 9000 Certification on Waste Management of Leather Industry

International Nuclear Information System (INIS)

Susetyo Hario Putero; Dhani Astuti

2008-01-01

State of industry in an area could increase economy of this area. On the other hand, industry may be produce the waste. There are many factor influencing the success of industrial waste management. At present, ISO 14000 is known as an international environmental management standard. Practically, several matter required for ISO 14000 are similar with ISO 9000. So, the role of ISO 9000 certification on supporting waste management program of leather industry has been studied. Study has been pursued by comparing the environmental management systems of 2 leather industries in Sitimulyo, Piyungan, Bantul. Staff working way has been observed to know the suitability with working procedures and implementation of safety aspect on daily working. Observation of waste treatment facility and measurement of Chrome concentration also has been done. Samples were analysed using AAS method in Department of Chemistry, Faculty of Mathematics and Natural Science, Gadjah Mada University. Decontamination Factor (DF) was calculated by comparing the Chrome concentrations on outside plant and in waste treatment facility. Commitment of management and orderliness of system as required on ISO 9000 certification could push the industry to well execute waste management program as a part of environmental management system. ISO 9000 certification is convinced to make awareness of industry grow for continually improving their capability, including their capacity of waste treatment facility. (author)

Spatial Diffusion of Leather Industries (Case Study at Magetan District

Directory of Open Access Journals (Sweden)

Dilahur Dilahur

2004-01-01

Full Text Available After the rise and the fall of the tides and the change of the activities as the phenomena which happen in the daily life of sociaety, the hange of spacing or distributionn of industrial businesses becomes one of the new phenomena. The objective of this research is to know the process of the diffusion from leather industry in Magetan Subdistrict. This research uses secondary data analysis and direct observation. The result of this research shows that the change (the rise and fall of the tides in leather industry has producted the movement of distribution or spacing in which the center of the main production is declined and the new center may arise. In this movement, it seems that the existence of the specification on types of activity, like having similar leather, shoescraft, beltcraft, and sendalcraft become the serious phenomena. This kind of the change and its development is signed by the change of position from becoming employee to be new employer, having some employees that may become the employers at any time and so forth. The style of the diffusion which happen is the style of mixing diffusion in which the business on leather industry becomes wider reaching around the village while the original village (Kauman is still as the center of industry, although it has so limited activities because the business is always declined.

Quantification of patulin in fruit leathers by ultra-high-performance liquid chromatography-photodiode array (UPLC-PDA).

Science.gov (United States)

Maragos, Chris M; Busman, Mark; Ma, Liang; Bobell, John

2015-01-01

Patulin is a mycotoxin commonly found in certain fruit and fruit products. For this reason many countries have established regulatory limits pertaining to, in particular, apple juice and apple products. Fruit leathers are produced by dehydrating fruit puree, leaving a sweet product that has a leathery texture. A recent report in the literature described the detection of patulin at substantial levels in fruit leathers. To investigate this further, an ultra-high-performance liquid chromatography-photodiode array (UPLC-PDA) method was developed for the sensitive detection of patulin in fruit leathers. Investigations were also made of the suitability of direct analysis in real time-mass spectrometry (DART-MS) for detection of patulin from the surface of fruit leathers. Results indicated DART-MS was insufficiently sensitive for quantification from the surface of home-style apple leathers, although patulin spiked onto the surface of leather or peel could be detected. The UPLC-PDA method was used to determine the fate of patulin during the preparation of home-made fruit leathers. Interestingly, when a home-style process was used, the patulin was not destroyed, but rather increased in concentration as the puree was dehydrated. The UPLC-PDA method was also used to screen for patulin in commercial fruit leathers. Of the 36 products tested, 14 were above the limit of detection (3.5 μg kg(-1)) and nine were above the limit of quantification (12 μg kg(-1)). Positive samples were confirmed by UPLC-MS/MS. Only one sample was found above the US regulatory limit for single-strength apple juice products (50 μg kg(-1)). These results suggest patulin can be concentrated during preparation and can be found in fruit leathers. The limited survey suggests that patulin is fairly prevalent in such commercial products, but that the levels are usually low.

DECONSTRUCTION OF TRADITIONAL ART: PRESENTATION STYLE OF CENK BLONK LEATHER PUPPET ON DEWATA TV

Directory of Open Access Journals (Sweden)

I Dewa Made Darmawan

2015-02-01

Full Text Available The presentation of Cenk Blonk Leather Puppet on Dewata TV, as a cultural phenomenon with a variety of complex problems, has been observed by most people. However, it is still enthusiastically welcome by the lovers of the Balinese leather puppet both in Bali and outside Bali. It seems that they are not aware of some basic changes in the way it is presented on TV. The way in which it is presented on TV is different from the way in which it is presented on the stage. It is such a cultural art which inspired the writer to explore and analyze in depth the way in which it is presented on TV. This study focuses on how the Cenk Blonk leather puppet is presented on Dewata TV to perform the theme “Dyah Ratna Takeshi”. It was found that the presentation of the Cenk Blonk leather puppet on Dewata TV in its program entitled “Pentas Wayang Kulit’ (the Leather Puppet Performance was the aesthetic presentation in which the elements of the traditional art were mixed with the modern technology medium (television. The material of the presentation of the Cenk Blonk leather puppet on Dewata TV employed the production of Bali Record which had been reprocessed (deconstructed and reconstructed. Advertisements and other materials were added and some parts were edited so that it suited the pattern of presentation and the slot of time during which it was presented. The Cenk Blonk leather puppet presented on Dewata TV was not completed with any accurate text and context. It gave impression that the traditional art was used to “package” advertisements and other promotions. The presentation of the Cenk Blonk leather puppet on Dewata TV proved to be able to attract many people, especially the young people. They were made to be addicted to the puppetry art. Before, they were not interested in it.

A REVIEW ON HEAVY METALS CONTENTS IN HIDE, SKIN AND PROCESSED LEATHERS

Directory of Open Access Journals (Sweden)

KOIZHAIGANOVA Meruyert

2016-05-01

Full Text Available Heavy metals are metals with high atomic weight which can be deposited in soil, water, plants and animals. It is generally known that mammal tissues are good bioindicators of trace elements, including heavy metals. Heavy metal analysis serves to identify and quantify the elements that are a potential hazard to the consumer after varying levels of contact. Usage area of leather is increasingly expanding in these days and it has also become a material requested and demanded by effect of fashion. Leather must protect its appearance and physical stability and also be problem-free in ecological terms and harmless to human health. There is a lack of data concerning the content of toxic elements in raw hide and skin of animals. Mainly information concerning metals content, including toxic ones, in processed leathers may be found in the literature. The aim of the present study was to review and compare the content of some heavy metals in raw hide, skin and the processed leathers in order to evaluate their accumulation and transition to the end-up product.

Comparative analysis of tannery-effluent contaminated soil and mixed culture bacterial inoculation on helianthus annuus L. growth

International Nuclear Information System (INIS)

Yasin, M.; Faisal, M.

2012-01-01

Here we reported the effect of four strains Bacillus pumilus-CrK08, Cellulosimicrobium cellulans-CrK16, Exiguobacterium-CrK19 and Bacillus cereus-CrK20 and tannery contaminated soil on Helianthus annuus L. var Hysun-33 growth parameters. Plants growing in tannery effluent contaminated soil have shown slowed leaf growth, reduced shoot length, burning of leaf margins and tips compared to plants growing in normal garden soil. The inoculated plants had shown overall increase in root length (15%), shoot length (33%) and fresh weight shoot (135%) compared to un-inoculated plants growing in stress conditions. Plants growing in tannery contaminated soil have shown increase in soluble proteins contents (9%), acid phosphatase activity (200%), peroxidase activity (203%) and decrease in chlorophyll a (39%), chlorophyll b (23%) and carotenoids contents (28%) compare to plants growing in normal control soil. Inoculated plants grown in contaminated soil have shown an increased in peroxidase activity, soluble proteins contents, acid phosphatase activity, chlorophyll a, b and carotenoid contents compare to respective un-inoculated plants. (author)

Nutrient content in maize fertilized with tannery sludge vermicompost and irrigated with domestic wastewater

Directory of Open Access Journals (Sweden)

Guilherme Malafaia

2016-11-01

Full Text Available This study analyzed the macro and micronutrient content of maize leaves (Zea mays L. grown in soil containing tannery sludge vermicomposting and irrigated with wastewater. The arrangement of the treatments consisted of a factorial 2x6 (two types of irrigation and six kinds of fertilizer in a completely randomized design, with five repetitions, totaling sixty experimental units. The following experimental units, irrigated with supply water (A and household wastewater (R, were established: (T1 Control Soil, with no chemical fertilization and no vermicomposting; (T2 Soil + NPK; (T3 Soil + primary sludge vermicompost; (T4 Soil + P + primary sludge vermicompost; (T5 Soil + P + liming sludge vermicompost; and (T6 Soil + liming sludge vermicompost. For the leaf-tissue analysis, the opposite whole leaf below the first (upper ear was collected from each plant, excluding the midrib at the onset of the female inflorescence. The results showed that both wastewater and the tannery sludge vermicomposts can be a good source of nutrients for maize plants, since the macro and micronutrients in the leaves of plants were satisfactory and no signs or symptoms of toxicity were observed. While leaf analysis alone is insufficient to assess the nutritional status of plants, this study innovatively suggests the potential beneficial use of a combination of wastewater and tannery sludge vermicompost in the cultivation of corn, motivating new research.

LETTUCE AND BROCCOLI RESPONSE AND SOIL PROPERTIES RESULTING FROM TANNERY WASTE APPLICATIONS

Science.gov (United States)

Broccoli (Brassica oleracea L. var. italica) and lettuce (Lactuca sativa L.) were grown on Willamette sil (Pachic Ultic Argixerolls) amended 1 and 2 yr earlier with chrome tannery wastes at rates up to 192 Mg ha to determine nutrient and trace element availability. Soils were sam...

CHROMIUM IN SOIL ORGANIC MATTER AND COWPEA AFTER FOUR CONSECUTIVE ANNUAL APPLICATIONS OF COMPOSTED TANNERY SLUDGE

Directory of Open Access Journals (Sweden)

Mara Lucia Jacinto Oliveira

2015-02-01

Full Text Available Tannery sludge contains high concentrations of inorganic elements, such as chromium (Cr, which may lead to environmental pollution and affect human health The behavior of Cr in organic matter fractions and in the growth of cowpea (Vigna unguiculata L. was studied in a sandy soil after four consecutive annual applications of composted tannery sludge (CTS. Over a four-year period, CTS was applied on permanent plots (2 × 5 m and incorporated in the soil (0-20 cm at the rates of 0, 2.5, 5.0, 10.0, and 20.0 Mg ha-1 (dry weight basis. These treatments were replicated four times in a randomized block design. In the fourth year, cowpea was planted and grown for 50 days, at which time we analyzed the Cr concentrations in the soil, in the fulvic acid, humic acid, and humin fractions, and in the leaves, pods, and grains of cowpea. Composted tannery sludge led to an increase in Cr concentration in the soil. Among the humic substances, the highest Cr concentration was found in humin. The application rates of CTS significantly increased Cr concentration in leaves and grains.

Two-stage phyto-microremediation of tannery effluent by Spirodela polyrrhiza (L.) Schleid. and chromium resistant bacteria.

Science.gov (United States)

Singh, Asha; Vyas, Dhiraj; Malaviya, Piyush

2016-09-01

Two-stage sequential treatment of tannery effluent was conducted employing a wetland plant, Spirodela polyrrhiza (L.) Schleid., and chromium (Cr) resistant bacterial strains. The bacterial strains were isolated from Cr-enriched environmental matrices and rhizosphere of Spirodela polyrrhiza. The phyto-rhizoremediation of tannery effluent by Spirodela and its rhizospheric bacteria (Cellulomonas biazotea APBR1-6, Bacillus safensis APBR2-12, Staphylococcus warneri APBR3-5, Microbacterium oleivorans APBR2-6), followed by microremediation by Cr resistant bacteria (Micrococcus luteus APBS5-1, Bacillus pumilus APBS5-2, Bacillus flexus APBE3-1, Virgibacillus sediminis APBS6-1) resulted in reduction of pollution parameters [COD (81.2%), total Cr (97.3%), Cr(VI) (99.3%), Pb(II) (97.0%), Ni (95.7%)]. The LC-MS analysis showed that many pollutants detected in untreated tannery effluent were diminished after bioremediation or long chains of alcohol polyethoxylates viz. C18EO6 in untreated effluent were broken down into smaller unit of alcohol polyethoxylate ((+)HHO[CH2CH2O]H), indicating that bacteria and Spirodela polyrrhiza, alongwith its rhizospheric associates utilized them as carbon and energy source. Copyright © 2016 Elsevier Ltd. All rights reserved.

LeatherNet: an evaluation as a mission planning and briefing tool

OpenAIRE

Hague, Tracy R.

1996-01-01

Information Technology Management The author evaluates LeatherNet, a Distributed Interactive Simulation compliant, virtual simulation system being developed by the Advanced Research Projects Agency to demonstrate Modeling and Simulation(M&S) technologies and to partially fulfill the U. S. Marine Corps M&S goals. The research focuses on evaluation of LeatherNet as a mission planning and briefing tool for Marine infantry company commanders, staff, and subordinate leaders. Evaluation is based...

Radioisotope investigations on the stratigraphic distribution of poly/methyl methacrylate/grafted onto leather

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1984-01-01

Investigations on the stratigraphic distribution of poly/methyl methacrylate/ in leather follow our earlier experiments on radiation grafting of vinyl monomers in situ. Polymer distribution was determined for pigskins and cattlehides tanned with basic sulphates of chromium/III/. 14 C-labelled methyl methacrylate was used in present experiments. Precision slicing technique was employed to cut consecutive slices parallel to the grain surface of the radiation modified leather. Quantative analysis of polymer distribution in leather was based on radioactivity measurements. Each layer was burned in Oxymat apparatus and resulting 14 CO 2 was analysed by liquid scintillation method. On the basis of radioactivity measurements and visual observations with light microscope conclusion on desirable distribution of polymer was reached. In the midcorium part of leather polymer is evenly distributed and its content is much higher than for outer layers next to surface and flesh. Mechanism of relevant processes as well as formation and role played by peroxide compounds is discussed

Radioisotope investigations on the stratigraphic distribution of poly(methyl methacrylate) grafted onto leather

International Nuclear Information System (INIS)

Pietrucha, K.; Kroh, J.

1985-01-01

Investigations on the stratigraphic distribution of poly(methyl methacrylate) in leather follow our earlier experiments on radiation grafting of vinyl monomers in situ. Polymer distribution was determined for pigskins and cattlehides tanned with basic sulphates of chromium (III). 14 C-labelled methyl methacrylate was used in present experiments. Precision slicing technique was employed to cut consecutive slices parallel to the grain surface of the radiation modified leather. Quantitative analysis of polymer distribution in leather was based on radioactivity measurements. Each layer was burned in Oxymat apparatus and resulting 14 CO 2 was analysed by liquid scintillation method. On the basis of radioactivity measurements and visual observations with light microscope conclusion on desirable distribution of polymer was reached. In the midcorium part of leather polymer is evenly distributed and its content is much higher than for outer layers next to surface and flesh. Mechanism of relevant processes as well as formation and role played by peroxide compounds are discussed. (author)

Valorization of titanium metal wastes as tanning agent used in leather industry.

Science.gov (United States)

Crudu, Marian; Deselnicu, Viorica; Deselnicu, Dana Corina; Albu, Luminita

2014-10-01

The development of new tanning agents and new technologies in the leather sector is required to cope with the increasingly higher environmental pressure on the current tanning materials and processes such as tanning with chromium salts. In this paper, the use of titanium wastes (cuttings) resulting from the process of obtaining highly pure titanium (ingots), for the synthesis of new tanning agent and tanning bovine hides with new tanning agent, as alternative to tanning with chromium salts are investigated. For this purpose, Ti waste and Ti-based tanning agent were characterized for metal content by inductively coupled plasma mass spectrometry (ICP-MS) and chemical analysis; the tanned leather (wet white leather) was characterized by Scanning Electron Microscope/Energy Dispersive Using X-ray (Analysis). SEM/EDX analysis for metal content; Differential scanning calorimetric (DSC), Micro-Hot-Table and standard shrinkage temperature showing a hydrothermal stability (ranged from 75.3 to 77°C) and chemical analysis showing the leather is tanned and can be processed through the subsequent mechanical operations (splitting, shaving). On the other hand, an analysis of major minor trace substances from Ti-end waste (especially vanadium content) in new tanning agent and wet white leather (not detected) and residue stream was performed and showed that leachability of vanadium is acceptable. The results obtained show that new tanning agent obtained from Ti end waste can be used for tanning bovine hides, as eco-friendly alternative for chrome tanning. Copyright © 2014 Elsevier Ltd. All rights reserved.

Chrome Tanning Leather of Giant Sea Perch Combined with Seed Extract Areca Nut on the Physical Characteristics

OpenAIRE

Bustami - Ibrahim; Ella - Salamah; Nurul - Hak; Ade Komalasari Suhendar

2014-01-01

Tanning is the process of converting raw hide protein to leather, which are stable, not easily decompose, and is suitable for a variety of uses. The use of vegetable based tanning materials in the leather tanning process has not been carried out. Vegetable based materials that were used are betel nuts. This plant contains tannin which is the main agent in the process of leather tanning. The aim of this study was to determine the physical characteristics of snapper leather treated with betel n...

Characteristics of chromium-allergic dermatitis patients prior to regulatory intervention for chromium in leather

DEFF Research Database (Denmark)

Bregnbak, David; Thyssen, Jacob P; Zachariae, Claus

2014-01-01

BACKGROUND: Chromium-tanned leather articles currently constitute the most important cause of contact allergy to chromium in Denmark. A regulation on the content of hexavalent chromium in leather was adopted in November 2013 by the EU member states. OBJECTIVES: To characterize patients...... with chromium allergy and their disease, to serve as a baseline for future studies on the potential effect of the new regulation on chromium in leather. METHODS: A questionnaire case-control study was performed on 155 dermatitis patients with positive patch test reactions to potassium dichromate and a matched...... control group of 621 dermatitis patients. Comparisons were made by use of a χ(2) -test and the Mann-Whitney U-test. Logistic regression analyses were used to test for associations. RESULTS: Sixty-six per cent of chromium-allergic patients had a positive history of contact dermatitis caused by leather...

Effect of Solar Radiation on Viscoelastic Properties of Bovine Leather: Temperature and Frequency Scans

Science.gov (United States)

Nalyanya, Kallen Mulilo; Rop, Ronald K.; Onyuka, Arthur S.

2017-04-01

This work presents both analytical and experimental results of the effect of unfiltered natural solar radiation on the thermal and dynamic mechanical properties of Boran bovine leather at both pickling and tanning stages of preparation. Samples cut from both pickled and tanned pieces of leather of appropriate dimensions were exposed to unfiltered natural solar radiation for time intervals ranging from 0 h (non-irradiated) to 24 h. The temperature of the dynamic mechanical analyzer was equilibrated at 30°C and increased to 240°C at a heating rate of 5°C \\cdot Min^{-1}, while its oscillation frequency varied from 0.1 Hz to 100 Hz. With the help of thermal analysis (TA) control software which analyzes and generates parameter means/averages at temperature/frequency range, the graphs were created by Microsoft Excel 2013 from the means. The viscoelastic properties showed linear frequency dependence within 0.1 Hz to 30 Hz followed by negligible frequency dependence above 30 Hz. Storage modulus (E') and shear stress (σ ) increased with frequency, while loss modulus (E''), complex viscosity (η ^{*}) and dynamic shear viscosity (η) decreased linearly with frequency. The effect of solar radiation was evident as the properties increased initially from 0 h to 6 h of irradiation followed by a steady decline to a minimum at 18 h before a drastic increase to a maximum at 24 h. Hence, tanning industry can consider the time duration of 24 h for sun-drying of leather to enhance the mechanical properties and hence the quality of the leather. At frequencies higher than 30 Hz, the dynamic mechanical properties are independent of the frequency. The frequency of 30 Hz was observed to be a critical value in the behavior in the mechanical properties of bovine hide.

CONTRIBUTIONS TO CLASSIFICATION ZIPPERS USED IN INDUSTRY FOOTWEAR AND LEATHER GOODS

OpenAIRE

MALCOCI Marina; PASCARI Ioana

2016-01-01

Now customary accessory companies of all leather garments, zipper began to enjoy popularity only after 80 years of its invention. The first is considered the inventor of the zipper Elias Howe. Essentially involves fashion, change, innovation, originality, creativity and is defined as a succession of trends or fads, short. Create fashionable leather confections from home means accepting a contract with the producer and / or consumer, showing a profit motivating all at the right time. Continuou...

Ultrasound assisted chrome tanning: Towards a clean leather production technology.

Science.gov (United States)

Mengistie, Embialle; Smets, Ilse; Van Gerven, Tom

2016-09-01

Nowadays, there is a growing demand for a cleaner, but still effective alternative for production processes like in the leather industry. Ultrasound (US) assisted processing of leather might be promising in this sense. In the present paper, the use of US in the conventional chrome tanning process has been studied at different pH, temperature, tanning time, chrome dose and US exposure time by exposing the skin before tanning and during tanning operation. Both prior exposure of the skin to US and US during tanning improves the chrome uptake and reduces the shrinkage significantly. Prior exposure of the skin to US increase the chrome uptake by 13.8% or reduces the chrome dose from 8% to 5% (% based on skin weight) and shorten the process time by half while US during tanning increases the chrome uptake by 28.5% or reduces the chrome dose from 8% to 4% (half) and the tanning time to one third compared to the control without US. Concomitantly, the resulting leather quality (measured as skin shrinkage) improved from 5.2% to 3.2% shrinkage in the skin exposed to US prior tanning and to 1.3% in the skin exposed to US during the tanning experiment. This study confirms that US chrome tanning is an effective and eco-friendly tanning process which can produce a better quality leather product in a shorter process time with a lower chromium dose. Copyright © 2016 Elsevier B.V. All rights reserved.

Use of ultrasound in leather processing industry: effect of sonication on substrate and substances--new insights.

Science.gov (United States)

Sivakumar, Venkatasubramanian; Swaminathan, Gopalaraman; Rao, Paruchuri Gangadhar; Muralidharan, Chellappa; Mandal, Asit Baran; Ramasami, Thirumalachari

2010-08-01

Influence of ultrasound (US) on various unit operations in leather processing has been studied with the aim to improve the process efficiency, quality, reduce process time and achieve near-zero discharge levels in effluent streams as a cleaner option. Effect of US on substrate (skin/leather) matrix as well as substances used in different unit operations have been studied and found to be useful in the processing. Absorption of US energy by leather in process vessel at different distances from US source has been measured and found to be significant. Effect of particle-size of different substances due to sonication indicates positive influence on the diffusion through the matrix. Our experimental results suggest that US effect is better realized for the cases with pronounced diffusion hindrance. Influence of US on bioprocessing of leather has been studied and found beneficial. Attempts have also been made to improve the US aided processing using external aids. Operating US in pulse mode operation could be useful in order to reduce the electrical energy consumption. Use of US has also been studied in the preparation of leather auxiliaries involving mass-transfer resistance. Preliminary cost analysis carried out for ultrasound-assisted leather-dyeing process indicates scale-up possibility. Therefore, US application provide improvement in process efficiency as well as making cleaner production methods feasible. Hence, overall results suggest that use of US in leather industry is imminent and potential viable option in near future. Copyright 2009 Elsevier B.V. All rights reserved.

How to revive Nigeria's neglected leather industry | Erumebor ...

African Journals Online (AJOL)

ERGP), the government needs to explore the inherent opportunities in the leather industry through promoting public-private partnership, providing scal incentives as well as enhancing technology and human capital development in the industry.

Chrome Tanning Leather of Giant Sea Perch Combined with Seed Extract Areca Nut on the Physical Characteristics

Directory of Open Access Journals (Sweden)

Bustami - Ibrahim

2014-11-01

Full Text Available Tanning is the process of converting raw hide protein to leather, which are stable, not easily decompose, and is suitable for a variety of uses. The use of vegetable based tanning materials in the leather tanning process has not been carried out. Vegetable based materials that were used are betel nuts. This plant contains tannin which is the main agent in the process of leather tanning. The aim of this study was to determine the physical characteristics of snapper leather treated with betel nut extract. Soxhlet extracting method with methanol as a solvent were used to obtain tannin from betel nuts. Tanned Snapper Leather were analyzed for physical quality, elongation strength, tensile strength, tear strength, and sewing strength. The result showed that methanol extracted betel nut with 10% concentration gives the optimum physical characteristics.Keywords: areca nut, chrome, snapper, snapper

Investigation of a Brazilian tannery effluent by means of zebra fish (Danio rerio) embryo acute toxicity (FET) test.

Science.gov (United States)

Rocha, Otávio Pelegrino; De Oliveira, Danielle Palma

2017-01-01

Tannery effluents consist of a complex chemical composition not only limited to primary pollutants, which also require biological detection as these compounds may produce adverse effects. The fish embryo toxicity (FET) test with Danio rerio is an alternative method in hazard and risk assessment for determination of chemical-mediated effects. The aim of this investigation was to use the FET test to detect compounds and consequent effects in Brazilian tannery effluents. Samples were collected from the inlet and outlet of the effluent treatment plant at a tannery located in Restinga, São Paulo, Brazil. The toxicological effects were assessed using FET assay for a period of 144 hr using indices such as (1) coagulation of fertilized eggs, (2) lack of detachment of tail-bud from yolk sac, (3) absence of spontaneous movement, (4) yolk sack edema, (5) malformation of the tail, (6) scoliosis, and (7) deformation of swim bladder in the embryos. Data showed that effluent treatment plant exposure produced acute toxicity in D. rerio embryos as evidenced by coagulation of fertilized eggs in up to 5% of all diluted samples 24 hr post fertilization for inlet effluent samples compared to 100% coagulation for outlet samples. Results demonstrated that these effects may not be attributed to metals, but to other non-detected components, such as dyes, pigments, biocides, carriers, surfactants, or other organic compounds that might be present in these complex mixtures. The use of D. rerio embryos was found to be useful as an additional tool for ecotoxicity testing to assess the potential environmental acute toxicity influence of tannery effluents.

Leather waste--potential threat to human health, and a new technology of its treatment.

Science.gov (United States)

Kolomaznik, K; Adamek, M; Andel, I; Uhlirova, M

2008-12-30

In this paper, the authors deal with the problem of processing various types of waste generated by leather industry, with special emphasis to chrome-tanned waste. The agent that makes this waste potentially hazardous is hexavalent chromium. Its compounds can have negative effects on human health and some CrVI salts are considered carcinogens. The authors present the risks of spontaneous oxidization of CrIII to CrVI in the open-air dumps as well as the possible risks of wearing bad quality shoes, in which the chromium content is not controlled. There are several ways of handling primary leather waste, but no satisfactory technology has been developed for the secondary waste (manipulation waste, e.g. leather scraps and used leather products). In this contribution, a new three-step hybrid technology of processing manipulation waste is presented and tested under laboratory, pilot-scale and industrial conditions. The filtrate can be used as a good quality NPK fertilizer. The solid product, titanium-chromium sludge, can serve as an inorganic pigment in glass and ceramic industry. Further, the authors propose selective collection of used leather products (e.g. old shoes), the hydrolysable parts of which can be also processed by the new hybrid technology.

production and characterization of activated carbon from leather

African Journals Online (AJOL)

dell

Powdered activated carbon (PAC) was prepared from leather buffing waste, sawdust and lignite by ... soil, air or water. (Baksi et al., 2006; ... anthracite and bituminous coal, lignite, lignocellulosic materials ..... waste water treatment: A review.

ANNALS OF THE UNIVERSITY OF ORADEA FASCICLE OF TEXTILES, LEATHERWORK 133 DETERMINANTS TO THE CONSUMPTION OF LEATHER PRODUCTS

Directory of Open Access Journals (Sweden)

CARRIER Serge A.

2014-05-01

Full Text Available The current paper looks at some of the determinants in the consumption of leather fashion products by the 16-34 year old population of Québec. Although the Québec population presents some idiosyncrasies, we surmise that our results could probably be generalized to similarly aged population groups in the western world. Leather goods are now often considered as luxury it ems, a sub-sector of the fashion industry which has been outgrowing all others in the last few years. Yet leather is often seen as non-ethical, requiring the killing of animals, and non-ecological, since the production process is polluting. Those two opposing forces make the future of leather very uncertain. Surprisingly, very little literature has been written on the subject. This paper presents a survey in which the authors tried to identify the determinants to the consumption of leather in the 16-34 age groups, often referred to as Generation Y. Our findings reflect this dichotomy between the consumer’s interest for apparel and his or her negative reaction to some characteristics of leather. Although not as influenced as fur by ethical and ecological concerns, leather products the object of similar reactions. This paper concludes on some recommendations to participants in the leather industry who should note this trend and try to position their products in such a way as to minimize the negative elements and bank on the more positive aspects.

The study of mildew proof effect of 60Co γ irradiation on leather shoes

International Nuclear Information System (INIS)

Wu Caixuan; Deng Zhiqun; Yu Qin; Zeng Daonan; Deng Guili

1992-01-01

Leather products occupy an important place in the national economy. In order to prevent from mildewing of leather products in storage, transportation and sale, the packed shoes were irradiated with 60 Co γ ray. Test materials are cattle, sheep and pig leather shoes. The results shows that: 1. There are 11 types of molds which make leather shoes mildewed: Oospora sp, Rhizopus oryzae Went and Grrelings, Aspergillus flavus Link, Aspergillus terreus thom, Monilia sp, Botrytis sp, Aspergillus niger V. Tiegh, Penicillum Lividum Westling, Penicillum Corylophilum Dieckx, Penicillum Cyaneum (B. and S.) Biourge and Penicillum Verrulosum Peeyrone. 2. The three types of shoes packed with polyethylene film can be prevented from mildewing after irradiation at level of 12 kGy. 3. The irradiation at 30 kGy does not change the physical properties of the shoes. 4. The irradiated shoes packed with polyethylene film can prevent mildewing, but unpacked ones would be mildewed again

Behavior and fate of heavy metals in the composting of industrial tannery sludge

International Nuclear Information System (INIS)

Mahdi Ahmed; Azni Idris; Omer, S.R.S.

2007-01-01

It is known that heavy metals, when in high enough concentrations, have the potential to be both phyto toxic and zoo toxic. Heavy metals are frequently found as contaminants in tannery sludge. Any sludge that is subsequently segregated for composting theoretically has the potential to retain the possible contamination. To date, there have been a limited number of publications addressing this issue. most reports have concentrated on the types of heavy metals found in the composting process. As such, this investigation aimed to identify the fate of chromium, cadmium, copper, lead and zinc, concentrations in tannery sludge throughout a fifty day composting cycle. The results of this study showed a general increase in the removal of Cr, Cd, Pb and to a much smaller extent Zn and Cu, evident by a decrease in their overall concentrations within the solid fraction of the final product, by 38.5, 33.3, 31.2, 22.6 and 11.8 percent respectively. (author)

Diminishing Chromium Use on Combined Chromium-Gambier Tanning Process Upon the Characteristics of Tanned Leather

Directory of Open Access Journals (Sweden)

A. Kasim

2014-04-01

Full Text Available The research was aimed to investigate the influence of minimizing chromium use on combined chromium-gambier process upon the characteristics of tanned leather. At the first stage of tanning process, chromium was used and in the second stage it was replaced by gambier. The raw material used was dried saline-preserved goat skin. The treatments applied on the tanning process were the different concentrations of chromium ranging from the highest level of 6% to the lowest level of 1% which was then re-tanned by using 8% concentration of gambier. The examination parameters included chemical and physical properties as well as visual investigation on the tanned leather in accordance with SNI-06-0463-1989-A. The result showed that the tanning process by using 2% chromium in the first step and 8% gambier in the second step was a treatment combination producing tanned leather that met the standard. The examination on tanned leather resulted from such treatment showed 56.33% rawhide, 17.45% of bound tannin, 31.22% of tanning level, tensile strength 386.30 kg/cm2, flexibility 31.91%, leather width 1.3 mm, density 0.75 g/cm3, the leather was quite elastic with light brownish color. In conclusion, minimizing the use of chromium in the combined tanning process of chromium and gambier can be implemented to the lowest of 2% chromium concentration and 8% gambier in the first and second step, respectively.

Greener Approach To Leather Techniques

OpenAIRE

Sah, Narayan

2013-01-01

The main purpose of this study was to find out greener and more ecological methods of leather tanning. In this thesis, old traditional methods and new developing methods are compared. New alternatives to chrome tanning agent and their benefits are reported. Additionally, efficient way of chrome tanning in presence of masking agents or other catalysts is reported with cleaning techniques using membrane processes such as micro-filtration, ultra-filtration (UF), nano-filtration (NF) and reverse ...

Fabrication of modified hydrogenated castor oil/GPTMS-ZnO composites and effect on UV resistance of leather.

Science.gov (United States)

Ma, Jianzhong; Duan, Limin; Lu, Juan; Lyu, Bin; Gao, Dangge; Wu, Xionghu

2017-06-16

Leather products are made from the natural skin collagen fibers. It is vulnerable to the environmental factor such as solar ultraviolet irradiation in the using process. Therefore anti-UV performance is a very important quality, particularly for chrome-free leather. ZnO is a well-known UV absorber commonly used in the cosmetic industry. We have investigated its potential to increase the anti-UV performance of chrome-free leather. Modified hydrogenated castor oil/GPTMS-ZnO (MHCO/ GPTMS-ZnO) composites were prepared using spherical ZnO nanoparticles, hydrogenated castor oil, maleic anhydride and sodium bisulfite. MHCO/GPTMS-ZnO composites have better anti-UV ability and stability. MHCO/GPTMS-ZnO composites were applied to the leather processing. The treated samples were exposed to artificial sunlight. Anti-yellowing tests showed that MHCO/GPTMS-ZnO composites significantly improved anti-UV performance of leather.

Organizational Buying Behavior of Selected Leather Footwear ...

African Journals Online (AJOL)

The purpose of this study is to assess the buying behavior of the Ethiopian leather footwear exporting companies in terms of supplier selection criteria, buying center, and factors affecting the purchasing process. In order to achieve the objective, a multiple case study approach is used in three case companies.

The influence of Chromium supplied by tanning and wet finishing processes on the formation of cr(vi in leather

Directory of Open Access Journals (Sweden)

W. F. Fuck

2011-06-01

Full Text Available Chromium used in leather manufacturing can be oxidized from the trivalent to the hexavalent state, causing environmental concerns. In this study, the influence of Cr(III from tanning, deacidification pH, fatliquors, chrome retanning and vegetable retanning on the formation of Cr(VI in leather was analyzed by comparing natural and aged samples. In wet-blue leather, even after aging and in fatliquored leathers that did not suffer the aging process, the presence of Cr(VI was always below the detection limit of 3 mg/kg. Considering the presence of Cr(VI, the supply of chromium during the retanning step had a more significant effect than during the tanning. In the fatliquoring process with sulfites, fish and synthetic fatliquor leather samples contained Cr(VI when aged, and the highest concentration detected was 26.7 mg/kg. The evaluation of Cr(VI formation led to recommendations for regulation in the leather industry.

Analysis of Selected Properties of Fibreboard Panels Manufactured from Wood and Leather Using the Near Infrared Spectroscopy

Directory of Open Access Journals (Sweden)

Kerstin Wagner

2015-01-01

Full Text Available This paper deals with the characterization of the properties of wood fibres leather shavings composite board by using the near infrared spectroscopy (NIRS and multivariate data analysis. In this study fibreboards were manufactured with different leather amounts by using spruce fibres, as well as vegetable and mineral tanned leather shavings (wet white and wet blue. The NIR spectroscopy was used to analyse the raw materials as well as the wood leather fibreboards. Moreover, the physical and mechanical features of the wood leather composite fibreboards were determined to characterize their properties for the further data analysis. The NIR spectra were analysed by univariate and multivariate methods using the Principal Component Analysis (PCA and the Partial Least Squares Regression (PLSR method. These results demonstrate the potential of FT-NIR spectroscopy to estimate the physical and mechanical properties (e.g., bending strength. This phenomenon provides a possibility for quality assurance systems by using the NIRS.

Analyses of Genetic Variations of Glutathione S-Transferase Mu1 and Theta1 Genes in Bangladeshi Tannery Workers and Healthy Controls

Directory of Open Access Journals (Sweden)

Jobaida Akther

2016-01-01

Full Text Available Glutathione S-transferases (GSTs belong to a group of multigene detoxification enzymes, which defend cells against oxidative stress. Tannery workers are at risk of oxidative damage that is usually detoxified by GSTs. This study investigated the genotypic frequencies of GST Mu1 (GSTM1 and GST Theta1 (GSTT1 in Bangladeshi tannery workers and healthy controls followed by their status of oxidative stress and total GST activity. Of the 188 individuals, 50.0% had both GSTM1 and GSTT1 (+/+, 12.2% had GSTM1 (+/−, 31.4% had GSTT1 (−/+ alleles, and 6.4% had null genotypes (−/− with respect to both GSTM1 and GSTT1 alleles. Among 109 healthy controls, 54.1% were double positive, 9.2% had GSTM1 allele, 32.1% had GSTT1 allele, and 4.6% had null genotypes. Out of 79 tannery workers, 44.3% were +/+, 16.8% were +/−, 30.5% were −/+, and 8.4% were −/−. Though the polymorphic genotypes or allelic variants of GSTM1 and GSTT1 were distributed among the study subjects with different frequencies, the differences between the study groups were not statistically significant. GST activity did not vary significantly between the two groups and also among different genotypes while level of lipid peroxidation was significantly higher in tannery workers compared to controls irrespective of their GST genotypes.

Analyses of Genetic Variations of Glutathione S-Transferase Mu1 and Theta1 Genes in Bangladeshi Tannery Workers and Healthy Controls

Science.gov (United States)

Akther, Jobaida; Ebihara, Akio; Nakagawa, Tsutomu; Islam, Laila N.; Suzuki, Fumiaki; Hosen, Md. Ismail; Hossain, Mahmud; Nabi, A. H. M. Nurun

2016-01-01

Glutathione S-transferases (GSTs) belong to a group of multigene detoxification enzymes, which defend cells against oxidative stress. Tannery workers are at risk of oxidative damage that is usually detoxified by GSTs. This study investigated the genotypic frequencies of GST Mu1 (GSTM1) and GST Theta1 (GSTT1) in Bangladeshi tannery workers and healthy controls followed by their status of oxidative stress and total GST activity. Of the 188 individuals, 50.0% had both GSTM1 and GSTT1 (+/+), 12.2% had GSTM1 (+/−), 31.4% had GSTT1 (−/+) alleles, and 6.4% had null genotypes (−/−) with respect to both GSTM1 and GSTT1 alleles. Among 109 healthy controls, 54.1% were double positive, 9.2% had GSTM1 allele, 32.1% had GSTT1 allele, and 4.6% had null genotypes. Out of 79 tannery workers, 44.3% were +/+, 16.8% were +/−, 30.5% were −/+, and 8.4% were −/−. Though the polymorphic genotypes or allelic variants of GSTM1 and GSTT1 were distributed among the study subjects with different frequencies, the differences between the study groups were not statistically significant. GST activity did not vary significantly between the two groups and also among different genotypes while level of lipid peroxidation was significantly higher in tannery workers compared to controls irrespective of their GST genotypes. PMID:27294127

Fitting Irregular Shape Figures into Irregular Shape Areas for the Nesting Problem in the Leather Industry

Directory of Open Access Journals (Sweden)

Guevara-Palma Luis

2015-01-01

Full Text Available The nesting problem of irregular shapes within irregular areas has been studied from several approaches due to their application in different industries. The particular case of cutting leather involves several restrictions that add complexity to this problem, it is necessary to generate products that comply with the quality required by customers This paper presents a methodology for the accommodation of irregular shapes in an irregular area (leather considering the constraints set by the footwear industry, and the results of this methodology when applied by a computer system. The scope of the system is to develop a working prototype that operates under the guidelines of a commercial production line of a sponsor company. Preliminary results got a reduction of 70% of processing time and improvement of 5% to 7% of the area usage when compared with manual accommodation.

Proposing and evaluating applications for products obtained during chromium chip alkaline hydrolysis produced during leather tanning

Directory of Open Access Journals (Sweden)

Andrea Díaz

2006-09-01

Full Text Available Some applications for products obtained by chromium chip alkaline hydrolysis produced during leather tanning were evaluated in this work, considering the concept of maximising tanneries’ solid residue reuse for different industrial applications and minimising the environmental impact so produced. When Cr(OH is transformed into Cr (OH(SO it can be used in tanning leather (i.e. as tanning salt. When compared to commercial salts, 2 4 it was determined that it could be applied to mixtures containing this salt, replacing it by up to 40%. Chromium content reduction was evaluated for collagen hydrolyzate by pH control after alkaline hydrolysis of the chips and by applying adsorbent materials such as bentonite, alfalfa and sorghum biomass and activated charcoal, a maximum 55% Cr removal being obtained when the first two adsorbent materials were used.

Correlation between bulk- and surface chemistry of Cr-tanned leather and the release of Cr(III) and Cr(VI)

Energy Technology Data Exchange (ETDEWEB)

Hedberg, Yolanda S., E-mail: yolanda@kth.se [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, SE-10044 Stockholm (Sweden); Institute of Environmental Medicine, Karolinska Institutet, Box 210, SE-17177 Stockholm (Sweden); Lidén, Carola, E-mail: carola.liden@ki.se [Institute of Environmental Medicine, Karolinska Institutet, Box 210, SE-17177 Stockholm (Sweden); Odnevall Wallinder, Inger, E-mail: ingero@kth.se [KTH Royal Institute of Technology, School of Chemical Science and Engineering, Department of Chemistry, Division of Surface and Corrosion Science, SE-10044 Stockholm (Sweden)

2014-09-15

Graphical abstract: - Highlights: • Released reducing/complexing leather-specific species can reduce released Cr(VI). • No co-released species enable the formation of Cr(VI) in solution. • The major Cr species released from leather in phosphate buffer was Cr(III) (>82%). • No Cr(VI) was released into artificial sweat. - Abstract: About 1–3% of the adult general population in Europe is allergic to chromium (Cr). The assessment of the potential release of Cr(III) and Cr(VI) from leather is hence important from a human health and environmental risk perspective. The Cr(VI) content in leather was recently restricted in the European Union. The aim of this study was to assess possible correlations between the bulk and surface chemistry of leather, released Cr(III) and Cr(VI), and capacities of co-released leather specific species to reduce and complex released Cr. Four differently tanned leathers were characterized by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, and the diphenylcarbazide colorimetric method. Their characteristics were compared with results on Cr(III) and Cr(VI) release into artificial sweat (ASW, pH < 6.5) and phosphate buffer (PB, pH 7.5–8.0), measured by means of spectrophotometry and atomic absorption spectroscopy. Co-released leather-specific species were shown to reduce Cr(VI), both in ASW and in PB. Their reduction capacities correlated with findings of the surface content of Cr and of released Cr. Leather samples without this capacity, and with less aromatic surface groups visible by ATR-FTIR, revealed Cr(VI) both at the surface and in solution (PB)

Pemanfaatan Buah Mengkudu (Morinda Citrifolia) Dan Kelopak Bunga Rosela (Hibiscus Sabdariffa LINN) Untuk Pembuatan Fruit Leather

OpenAIRE

Winarti, Sri

2008-01-01

The research about production of fruit leather from morinda-roselle with variation the proportion and added bind- ing agent was carried out. Fruit leather is a food product like the skin, having consistency and special taste from the special fruits. In Indonesia, fruit leather is a new product, because it has not been found at the market, but in overseas this product is very famous as the snack food. The purpose of this research were to find the best proportion between morinda and roselle, wh...

Pemanfaatan Buah Mengkudu (Morinda citrifolia) dan Kelopak Bunga Rosela (Hibiscus sabdariffa LINN) untuk Pembuatan Fruit Leather

OpenAIRE

Winarti, Sri

2012-01-01

The research about production of fruit leather from morinda-roselle with variation the proportion and added bind- ing agent was carried out. Fruit leather is a food product like the skin, having consistency and special taste from the special fruits. In Indonesia, fruit leather is a new product, because it has not been found at the market, but in overseas this product is very famous as the snack food. The purpose of this research were to find the best proportion between morinda and roselle, wh...

[Determination of short chain chlorinated paraffins in leather products by solid phase extraction coupled with gas chromatography-mass spectrometry].

Science.gov (United States)

Zhang, Weiya; Wan, Xin; Li, Lixia; Wang, Chengyun; Jin, Shupei; Xing, Jun

2014-10-01

The short chain chlorinated paraffins (SCCPs) are the additives frequently used in the leather production in China, but they have been put into the list of forbidden chemicals issued by European Union recently. In fact, there is not a commonly recognized method for the determination of the SCCPs in the leather products due to the serious matrix interferences from the leather products and the complex chemical structures of the SCCPs. A method of solid phase extraction coupled with gas chromatography-mass spectrometry (SPE-GC-MS) was established for the determination of the SCCPs in the leather products after the optimization of the SPE conditions. It was found that the interferences from the leather products were thor- oughly separated from the analyte of the SCCPs on a home-made solid phase extraction (SPE) column filled with silica packing while eluted with a mixed solvent of n-hexane-methylene chloride (2:1, v/v). With this method, the recoveries for the SCCPs spiked in the real leather samples varied from 90.47% to 99.00% with the relative standard deviations (RSDs) less than 6.7%, and the limits of detection (LODs) were between 0.069 and 0.110 mg/kg. This method is suitable for qualitative and quantitative analysis of SCCPs in the leather products.

Biogas recovery from tanning sludges. Anaerobic digestion of lime fleshings, tanning sludge, and unhairing baths, laboratory and pilot scale results

Energy Technology Data Exchange (ETDEWEB)

Fendrup, W.; Hansen, S.; Petersen, G.

1983-11-01

Mesophilic anaerobic digestion of various types of tannery and other wastes, separately or in mixtures, has been investigated. The following materials were used: Lime fleshings, Tannery sludge, Beamhouse sludge, Municipal sludge, Chrome leather shavings, Liquid manure. The investigations have shown anaerobic digestion to be possible with untanned tannery wastes as well as tannery effluent sludge as a substrate. Specially high gas yields were found by digestion of mixtures of tannery wastes and manure. This may be applicable to mixtures of tannery wastes and municipal sludge, too. The gas contains 0.5 - 1.0% H2S. About 25% of the gross energy (methane) output is used for sustaining the temperature necessary for the digestion together with the mixing and conveying of the material to be digested. If electricity is produced, 25% of the gross output is obtained as useful electric energy and 35% as useful thermic energy. If the gas is burned, 60% of the gross output is obtained as useful thermic energy. With the price relations found in most countries (e.g. Denmark, Finland and Sweden) it will be most profitable to produce electricity, whereas in some cases (e.g. Norway) the opposite may be true. The energy requirement of a typic Scandinavian tannery is 14.200 MJ/t rawhide as thermic energy and 2.300 MJ/t rawhide as electric energy, which means that maximum 14% of the thermic energy requirement or maximum 35% of the electricity requirement could be covered by the wastes digestion. Profitability calculations are made for each Scandinavian country. The calculations show that too small digestion plants are not profitable.

Nanomaterials for the cleaning and pH adjustment of vegetable-tanned leather

Science.gov (United States)

Baglioni, Michele; Bartoletti, Angelica; Bozec, Laurent; Chelazzi, David; Giorgi, Rodorico; Odlyha, Marianne; Pianorsi, Diletta; Poggi, Giovanna; Baglioni, Piero

2016-02-01

Leather artifacts in historical collections and archives are often contaminated by physical changes such as soiling, which alter their appearance and readability, and by chemical changes which occur on aging and give rise to excessive proportion of acids that promote hydrolysis of collagen, eventually leading to gelatinization and loss of mechanical properties. However, both cleaning and pH adjustment of vegetable-tanned leather pose a great challenge for conservators, owing to the sensitivity of these materials to the action of solvents, especially water-based formulations and alkaline chemicals. In this study, the cleaning of historical leather samples was optimized by confining an oil-in-water nanostructured fluid in a highly retentive chemical hydrogel, which allows the controlled release of the cleaning fluid on sensitive surfaces. The chemical gel exhibits optimal viscoelasticity, which facilitates its removal after the application without leaving residues on the object. Nanoparticles of calcium hydroxide and lactate, dispersed in 2-propanol, were used to adjust the pH up to the natural value of leather, preventing too high alkalinity which causes swelling of fibers and denaturation of the collagen. The treated samples were characterized using scanning electron microscopy, controlled environment dynamic mechanical analysis, and infrared spectroscopy. The analytical assessment validated the use of tools derived from colloid and materials science for the preservation of collagen-based artifacts.

Hydrolysis of proteinaceous tannery solid waste for the production of ...

African Journals Online (AJOL)

user

2012-07-12

Jul 12, 2012 ... The isolate was found to produce maximum protease at pH 6 and at a temperature of ... such as laundry detergents, leather preparation, protein recovery or ... pea” wastes (Gessesse, 1997), “feather” meal (Johnvesly.

Experimental skin deposition of chromium on the hands following handling of samples of leather and metal

DEFF Research Database (Denmark)

Bregnbak, David; Thyssen, Jacob P.; Jellesen, Morten Stendahl

2016-01-01

Background: Chromium is an important skin sensitizer. Exposure to it has been regulated in cement, and recently in leather. Studies on the deposition of chromium ions on the skin as a result of handling different chromium-containing materials are sparse, but could improve the risk assessment...... of contact sensitization and allergic contact dermatitis caused by chromium. Objectives: To determine whether the handling of chromium-containing samples of leather and metal results in the deposition of chromium onto the skin. Methods: Five healthy volunteers participated. For 30 min, they handled samples...... of leather and metal known to contain and release chromium. Skin deposition of chromium was assessed with the acid wipe sampling technique. Results: Acid wipe sampling of the participants' fingers showed chromium deposition on the skin in all participants who had been exposed to leather (range 0.01–0.20 µg...

Chromium(III) and chromium(VI) release from leather during 8 months of simulated use.

Science.gov (United States)

Hedberg, Yolanda S; Lidén, Carola

2016-08-01

Chromium (Cr) release from Cr-tanned leather articles is a major cause of Cr contact dermatitis. It has been suggested that Cr(VI) release from leather is not necessarily an intrinsic property of the leather, but is strongly dependent on environmental conditions. To test this hypothesis for long-term (8 months) simulated use. The release of total Cr and Cr(VI) from Cr-tanned, unfinished leather was analysed in subsequent phosphate buffer (pH 8.0) immersions for a period of 7.5 months. The effect of combined ultraviolet treatment and alkaline solution (pH 12.1) was tested. Dry storage [20% relative humidity (RH)] was maintained between immersions. Atomic absorption spectroscopy, X-ray fluorescence and diphenylcarbazide tests were used. Cr(VI) release was dependent on previous dry storage or alkaline treatment, but not on duration or number of previous immersions. Cr(III) release decreased with time. Fifty-two percent of the total Cr released during the last immersion period was Cr(VI). Cr(VI) release exceeded 9 mg/kg in all immersion periods except in the first 10-day immersion (2.6 mg/kg). Cr(VI) release is primarily determined by environmental factors (RH prior to immersion, solution pH, and antioxidant content). The RH should be kept low prior to testing Cr(VI) release from leather. © 2016 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.

Kajian Karakteristik Fisikokimia Dan Sensoris Fruit Leather Nangka (Artocarpus Heterophyllus) Dengan Penambahan Karaginan

OpenAIRE

Fitantri, Arinda Laksmi; Parnanto, Nur Her Riyadi; Praseptiangga, Danar

2014-01-01

Dalam penelitian ini dibuat fruit leather nangka (Artocarpus heterophyllus) dengan variasi penambahan karaginan (0%; 0,3%; 0,6% dan 0,9%) dengan tujuan untuk mengetahui karakteristik fisikokimia (kuat tarik, kadar air, kadar abu, Aw, kadar serat pangan, dan kadar gula reduksi) serta karakteristik sensoris fruit leather nangka. Rancangan penelitian ini menggunakan Rancangan Acak Lengkap (RAL) dengan satu faktor yaitu konsentrasi karaginan. Masing-masing perlakuan dilakukan dua kali ulangan sam...

Use of flying ash in the chromium removal (III) of the liquid effluents of tanneries

International Nuclear Information System (INIS)

Gil Pavas, Edison; Saldarriaga Molina, Carlos

1998-01-01

This study describes a simple and economic method for the removal of chromium (III) from tannery waste waters using flying ash. The process is carried out batch-wise utilizing as variables the mass of flying ash, the time of contact and the temperature or pH. With these variables a Box-Wilson type of experimental design was done, which was then optimized with a statistical program. One as-received flying ash was utilized in the work as well as another one chemically treated. The results show the possibility of lowering the initial concentration in the waste liquor from 1850 ppm to 0,008, complying this way with environmental exigencies about this contaminant

Treatment of tannery wastewater for reuse by physico-chemical processes and a membrane bioreactor

Directory of Open Access Journals (Sweden)

J. Fettig

2017-12-01

Full Text Available Treatment of wastewater from a tannery in Greater Ho Chi Minh City (Vietnam was investigated on a pilot scale. After pre-treatment by the tannery that included batch-coagulation and sedimentation, the wastewater was treated by dissolved air flotation, a membrane bioreactor (MBR and granular activated carbon (GAC for polishing the MBR effluent. The average removal efficiency for organic substances in the MBR was 81% while total nitrogen could only be removed by 36%. The performance of the GAC column could be successfully predicted using adsorption parameters determined in laboratory experiments. A larger proportion of the organics in the MBR effluent was only weakly adsorbable, therefore the usable carbon capacity was limited as confirmed by the modelling approach. The results were used to outline the size of a technical plant with a volumetric loading rate of 3 kg COD/(m3*d for the MBR and a specific carbon demand of about 1.8 kg/m3.

Effective bioleaching of chromium in tannery sludge with an enriched sulfur-oxidizing bacterial community.

Science.gov (United States)

Zeng, Jing; Gou, Min; Tang, Yue-Qin; Li, Guo-Ying; Sun, Zhao-Yong; Kida, Kenji

2016-10-01

In this study, a sulfur-oxidizing community was enriched from activated sludge generated in tannery wastewater treatment plants. Bioleaching of tannery sludge containing 0.9-1.2% chromium was investigated to evaluate the effectiveness of the enriched community, the effect of chromium binding forms on bioleaching efficiency, and the dominant microbes contributing to chromium bioleaching. Sludge samples inoculated with the enriched community presented 79.9-96.8% of chromium leaching efficiencies, much higher than those without the enriched community. High bioleaching efficiencies of over 95% were achieved for chromium in reducible fraction, while 60.9-97.9% were observed for chromium in oxidizable and residual fractions. Acidithiobacillus thiooxidans, the predominant bacteria in the enriched community, played an important role in bioleaching, whereas some indigenous heterotrophic species in sludge might have had a supporting role. The results indicated that A. thiooxidans-dominant enriched microbial community had high chromium bioleaching efficiency, and chromium binding forms affected the bioleaching performance. Copyright © 2016 Elsevier Ltd. All rights reserved.

A review on management of chrome-tanned leather shavings: a holistic paradigm to combat the environmental issues.

Science.gov (United States)

Pati, Anupama; Chaudhary, Rubina; Subramani, Saravanabhavan

2014-10-01

Raw hide/skins come to the tanners as a by-product of meat industry which is converted into value-added leather as product for fashion market. Leather manufacturing is a chemical process of natural biological matrix. It employs a huge quantity of water and inorganic and organic chemicals for processing and thereby discharges solid and liquid wastes into the environment. One of the potential solid wastes generated from leather industry is chrome-tanned leather shavings (CTLSs), and its disposal is increasingly becoming a huge challenge on disposal to tanners due to presence of heavy metal chromium. Hence, finding a sustainable solution to the CTLS disposal problem is a prime challenge for global tanners and researchers. This paper aims to the deeper review of various disposal methods on CTLS such as protein, chromium, and energy recovery processes and its utilization methodologies. Sustainable technologies have been developed to overcome CTLS solid wastes emanating from leather processing operations. Further, this review paper brings a broader classification of developed methodologies for treatment of CTLSs.

Production of Prodigiosin Using Tannery Fleshing and Evaluating Its Pharmacological Effects

Directory of Open Access Journals (Sweden)

C. Sumathi

2014-01-01

Full Text Available Aim. The focal theme of present investigation includes isolation of prodigiosin producing fish gut bacteria, enhancing its production using tannery solid waste fleshing, and evaluation of its pharmacological effect. Methods. Optimization of fermentation conditions to yield maximum prodigiosin, and instrumental analysis using FTIR, NMR, ESI-MS, TGA, and DSC. Results. The optimum conditions required for the maximum prodigiosin concentration were achieved at time 30 h, temperature 30°C, pH 8, and 3% substrate concentration. The secondary metabolite was analyzed using ESI-MS, FTIR, and NMR. Therapeutic efficacy was assessed by in vitro anticancer studies. Among the pathogenic bacteria Pseudomonas aeruginosa was most susceptible at the lowest concentration followed by Salmonella typhi. IC50 concentration was cell line specific (HeLa cells: 4.3 µM, HEp2: 5.2 µM, and KB cells: 4.8 µM and remains nontoxic up to the concentration of 25 µM on normal Vero cells suggesting that cancerous cells are more susceptible to the prodigiosin at lower concentration. Conclusion. Maximum prodigiosin production was obtained with tannery fleshing. The potency of the fish gut bacterial secondary metabolite prodigiosin as a therapeutic agent was confirmed through in vitro antimicrobial and anticancer studies.

Thermal Properties of Anionic Polyurethane Composition for Leather Finishing

Directory of Open Access Journals (Sweden)

Olga KOVTUNENKO

2016-09-01

Full Text Available Thermal properties of anionic polyurethane composition mixed with collagen product and hydrophilic sodium form of montmorillonite for use in the finishing of leather were studied by thermogravimetric method. The thermal indices of processes of thermal and thermo-oxidative destruction depending on the polyurethane composition were determined. The influence of anionic polyurethane composition on thermal behavior of chromium tanned gelatin films that imitate the leather were studied. APU composition with natural compounds increases their thermal stability both in air and in nitrogen atmosphere due to the formation of additional bonds between active groups of APU, protein and chrome tanning agent as the result of chemical reactions between organic and inorganic parts with the new structure formation.DOI: http://dx.doi.org/10.5755/j01.ms.22.3.10043

CO₂ Separation and Capture Properties of Porous Carbonaceous Materials from Leather Residues.

Science.gov (United States)

Bermúdez, José M; Dominguez, Pablo Haro; Arenillas, Ana; Cot, Jaume; Weber, Jens; Luque, Rafael

2013-10-18

Carbonaceous porous materials derived from leather skin residues have been found to have excellent CO₂ adsorption properties, with interestingly high gas selectivities for CO₂ (α > 200 at a gas composition of 15% CO₂/85% N₂, 273K, 1 bar) and capacities (>2 mmol·g -1 at 273 K). Both CO₂ isotherms and the high heat of adsorption pointed to the presence of strong binding sites for CO₂ which may be correlated with both: N content in the leather residues and ultrasmall pore sizes.

Soybean plant growth study conducted using purified protein hydrolysate-based fertilizer made from chrome-tanned leather waste.

Science.gov (United States)

Pati, Anupama; Chaudhary, Rubina

2015-12-01

Leather processing discharges enormous amount of chrome containing leather solid waste which creates a major disposal problem. Chrome-tanned leather solid waste is a complex of collagen and chromium. The presence of chromium limits protein application in fertilizer industry. The purified protein hydrolysate with zero chromium could be used as a nitrogen source for fertilizer formulation. In this study, an attempt has been made to employ purified protein hydrolysate derived from chrome-tanned leather shavings (CTLS) in formulation of fertilizer. The formulated fertilizer (1–3 t ha(-1)) is employed as nitrogen source in production of soybean. Plant growth study demonstrates that formulated fertilizer dosage 3 t ha(-1) produced similar effects of commercial fertilizer-treated plants. Application of formulated fertilizer yielded higher seed in plant than commercial fertilizer.

Sinos River Hydrographic Basin: urban occupation, industrialization and environmental memory

Directory of Open Access Journals (Sweden)

M. F. Nunes

Full Text Available This article presents an analysis of the process of industrialization and urbanization of the Sinos Valley in Rio Grande do Sul state, Brazil, starting from the establishment of leather goods and footwear manufacturing in the region during the 19th century when tanneries and factories producing footwear and/or components for footwear began to appear, and with special attention to aspects related to the environmental impact on the Sinos river hydrographic basin. The article is based on both bibliographic and documentary research and also draws on biographical narratives of workers with links to the leather goods and footwear industry obtained using ethnographic method. It was found that contemporary environmental conflicts emerge from within a memory of work and an environmental memory in which the factories, the unplanned urbanization, and the utilization of water and other natural resources form a chain of significance. Significance that precludes any form of fragmented analysis that isolates any of these aspects from the others: the economic, socio-historic, cultural, political, or the environmental.

Sinos River Hydrographic Basin: urban occupation, industrialization and environmental memory.

Science.gov (United States)

Nunes, M F; Figueiredo, J A S; Rocha, A L C

2015-12-01

This article presents an analysis of the process of industrialization and urbanization of the Sinos Valley in Rio Grande do Sul state, Brazil, starting from the establishment of leather goods and footwear manufacturing in the region during the 19th century when tanneries and factories producing footwear and/or components for footwear began to appear, and with special attention to aspects related to the environmental impact on the Sinos river hydrographic basin. The article is based on both bibliographic and documentary research and also draws on biographical narratives of workers with links to the leather goods and footwear industry obtained using ethnographic method. It was found that contemporary environmental conflicts emerge from within a memory of work and an environmental memory in which the factories, the unplanned urbanization, and the utilization of water and other natural resources form a chain of significance. Significance that precludes any form of fragmented analysis that isolates any of these aspects from the others: the economic, socio-historic, cultural, political, or the environmental.

Measurement of Surface Damage through Boundary Detection: An Approach to Assess Durability of Cementitious Composites under Tannery Wastewater

Directory of Open Access Journals (Sweden)

Tanvir Manzur

2016-01-01

Full Text Available Concrete structures are often subjected to aggressive aqueous environments which consist of several chemical agents that can react with concrete to produce adverse effects. A Central Effluent Treatment Plant consisting of reinforced concrete structures which is being constructed at Savar, Bangladesh, is an example of such a case. The purpose of this treatment facility is to reduce the environmental pollution created by tannery wastewater. However, tannery wastewater consists of several chemicals such as sulfates, chlorides, and ammonium, which, from the literature, are known to generate detrimental effects on concrete. Evaluation of durability of concrete structures in such environments is therefore imperative. This paper highlights a technique of boundary detection developed through image processing performed using MATLAB. Cement mortar cubes were submerged in simulated tannery wastewater and the images of the surface of cubes were taken at several time intervals. In addition, readings for compressive strength and weight were also taken on the same days. In this paper, an attempt is made to correlate the results from image processing with that of strength and weight loss. It was found, within the scope of this study, that the specimens which suffered greater strength and weight loss also underwent greater loss of surface area.

Preparation and characterization of hierarchical porous carbons derived from solid leather waste for supercapacitor applications

International Nuclear Information System (INIS)

Konikkara, Niketha; Kennedy, L. John; Vijaya, J. Judith

2016-01-01

Highlights: • Solid leather waste was used as a precursor for preparing HPCs—waste to energy storage. • The textural, structural and morphological properties show the hierarchical porous nature. • Porous carbon with surface area 716 m"2/g and pore volume 0.4030 cm"3/g has been produced. • HPCs based supercapacitor electrodes are fabricated with three electrode system in 1 M KCl. • Specific capacitance of 1960 F/g is achieved at scan rate of 1 mV/s in 1 M KCl. - Abstract: Utilization of crust leather waste (CLW) as precursors for the preparation of hierarchical porous carbons (HPC) were investigated. HPCs were prepared from CLW by pre-carbonization followed by chemical activation using KOH at relatively high temperatures. Textural properties of HPC’s showed an extent of micro-and mesoporosity with maximum BET surface area of 716 m"2/g. Inducements of graphitic planes in leather waste derived carbons were observed from X-ray diffraction and HR-TEM analysis. Microstructure, thermal behavior and surface functional groups were identified using FT-Raman, thermo gravimetric analysis and FT-IR techniques. HPCs were evaluated for electrochemical properties by cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) and electrochemical impedance spectroscopy (EIS) by three electrode system. CLC9 sample showed a maximum capacitance of 1960 F/g in 1 M KCl electrolyte. Results achieved from rectangular curves of CV, GCD symmetric curves and Nyquist plots show that the leather waste carbon is suitable to fabricate supercapacitors as it possess high specific capacitance and electrochemical cycle stability. The present study proposes an effective method for solid waste management in leather industry by the way of converting toxic leather waste to new graphitic porous carbonaceous materials as a potential candidate for energy storage devices.

Preparation and characterization of hierarchical porous carbons derived from solid leather waste for supercapacitor applications

Energy Technology Data Exchange (ETDEWEB)

Konikkara, Niketha [Materials Division, School of Advanced Sciences, Vellore Institute of Technology (VIT) University, Chennai Campus, Chennai 600 127 (India); Kennedy, L. John, E-mail: jklsac14@yahoo.co.in [Materials Division, School of Advanced Sciences, Vellore Institute of Technology (VIT) University, Chennai Campus, Chennai 600 127 (India); Vijaya, J. Judith [Catalysis and Nanomaterials Research Laboratory, Department of Chemistry, Loyola College (Autonomous) Chennai 600 034 (India)

2016-11-15

Highlights: • Solid leather waste was used as a precursor for preparing HPCs—waste to energy storage. • The textural, structural and morphological properties show the hierarchical porous nature. • Porous carbon with surface area 716 m{sup 2}/g and pore volume 0.4030 cm{sup 3}/g has been produced. • HPCs based supercapacitor electrodes are fabricated with three electrode system in 1 M KCl. • Specific capacitance of 1960 F/g is achieved at scan rate of 1 mV/s in 1 M KCl. - Abstract: Utilization of crust leather waste (CLW) as precursors for the preparation of hierarchical porous carbons (HPC) were investigated. HPCs were prepared from CLW by pre-carbonization followed by chemical activation using KOH at relatively high temperatures. Textural properties of HPC’s showed an extent of micro-and mesoporosity with maximum BET surface area of 716 m{sup 2}/g. Inducements of graphitic planes in leather waste derived carbons were observed from X-ray diffraction and HR-TEM analysis. Microstructure, thermal behavior and surface functional groups were identified using FT-Raman, thermo gravimetric analysis and FT-IR techniques. HPCs were evaluated for electrochemical properties by cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) and electrochemical impedance spectroscopy (EIS) by three electrode system. CLC9 sample showed a maximum capacitance of 1960 F/g in 1 M KCl electrolyte. Results achieved from rectangular curves of CV, GCD symmetric curves and Nyquist plots show that the leather waste carbon is suitable to fabricate supercapacitors as it possess high specific capacitance and electrochemical cycle stability. The present study proposes an effective method for solid waste management in leather industry by the way of converting toxic leather waste to new graphitic porous carbonaceous materials as a potential candidate for energy storage devices.

Health hazards of child labor in the leather products and surgical instrument manufacturing industries of Sialkot, Pakistan

International Nuclear Information System (INIS)

Junaid, Muhammad; Malik, Riffat Naseem; Pei, De-Sheng

2017-01-01

Child labor is a major challenge in the developing countries and comprehensive health hazard identification studies on this issue are still lacking. Therefore, the current study is an effort to highlight the health concerns of child labor exposed in the key small scale industries of Sialkot, Pakistan. Our findings revealed jolting levels of heavy metals in the urine, blood, serum, saliva, and hair samples collected from the exposed children. For example, in the urine samples, Cd, Cr, Ni, and Pb were measured at the respective concentrations of 39.17, 62.02, 11.94 and 10.53 μg/L in the surgical industries, and 2.10, 4.41, 1.04 and 5.35 μg/L in the leather industries. In addition, source apportionment revealed polishing, cutting, and welding sections in the surgical industries and surface coating, crusting, and stitching sections in the leather industries were the highest contributors of heavy metals in the bio-matrices of the exposed children, implying the dusty, unhygienic, and unhealthy indoor working conditions. Further, among all the bio-matrices, the hair samples expressed the highest bioaccumulation factor for heavy metals. In accordance with the heavy metal levels reported in the exposed children, higher oxidative stress was found in the children working in the surgical industries than those from the leather industries. Moreover, among heavy metals’ exposure pathways, inhalation of industrial dust was identified as the primary route of exposure followed by the ingestion and dermal contact. Consequently, chemical daily intake (CDI), carcinogenic and non-carcinogenic hazard quotients (HQs) of heavy metals were also reported higher in the exposed children and were also alarmingly higher than the corresponding US EPA threshold limits. Taken all together, children were facing serious health implications in these industries and need immediate protective measures to remediate the current situation. - Highlights: • Children occupational exposure assessment

Leather material found on a 6th B.C. Chinese bronze sword: A technical study

Science.gov (United States)

Luo, Wugan; Si, Yi; Wang, Hongmin; Qin, Ying; Huang, Fengchun; Wang, Changsui

2011-09-01

During July to November, 2006, an important archaeological excavation was conducted in Yun country, Hubei province, southern China. Chinese archaeologists found some remnant of leather materials, covered with red pigments, on a 6th century B.C. Chinese bronze sword. To understand the technology/ies that may have been utilized for manufacturing the leathers, a combined of Raman spectroscopy, FT-IR and XRF was thus applied to the remnant of leather materials. Raman analyses showed that red pigment on the leather was cinnabar (HgS). FT-IR and XRF analyses indicated that the content of some elements, such as Ca (existing as CaCO 3) and Fe (existing as Fe 2O 3), were much higher than those in the surrounding grave soil. The results inferred an application of lime depilation and retting, and the Fe-Al compound salt as tanning agent. And it was furthermore implicated that the Fe-Al salt tanning technique had been developed in the middle and late Spring and Autumn Period of China.

Kinetics of leather dyeing pretreated with enzymes: role of acid protease.

Science.gov (United States)

Kanth, Swarna Vinodh; Venba, Rajangam; Jayakumar, Gladstone Christopher; Chandrababu, Narasimhan Kannan

2009-04-01

In the present investigation, kinetics of dyeing involving pretreatment with acid protease has been presented. Application of acid protease in dyeing process resulted in increased absorption and diffusion of dye into the leather matrix. Enzyme treatment at 1% concentration, 60 min duration and 50 degrees C resulted in maximum of 98% dye exhaustion and increased absorption rate constants. The final exhaustion (C(infinity)) for the best fit of CI Acid Black 194 dye has been 98.5% with K and r2 values from the modified Cegarra-Puente isotherm as 0.1033 and 0.0631. CI Acid Black 194 being a 2:1 metal complex acid dye exhibited higher absorption rate than the acid dye CI Acid Black 210. A reduction in 50% activation energy calculated from Arrhenius equation has been observed in enzyme assisted dyeing process of both the dyes that substantiates enhanced dye absorption. The absorption rate constant calculated with modified Cegarra-Puente equation confirm higher rate constants and faster kinetics for enzyme assisted dyeing process. Enzyme treated leather exhibited richness of color and shade when compared with control. The present study substantiates the essential role of enzyme pretreatment as an eco-friendly leather dyeing process.

Fluctuations in the prevalence of chromate allergy in Denmark and exposure to chrome-tanned leather

DEFF Research Database (Denmark)

Carøe, Caroline; Andersen, Klaus E; Thyssen, Jacob P

2010-01-01

A recent Danish study showed a significant increase in the prevalence of chromate contact allergy after the mid-1990s, probably as a result of exposure to leather products.......A recent Danish study showed a significant increase in the prevalence of chromate contact allergy after the mid-1990s, probably as a result of exposure to leather products....

Computational fluid dynamics (CFD) analysis of the combustion process of a leather residuals gasification fuel gas: influence of fuel moisture content

Energy Technology Data Exchange (ETDEWEB)

Antonietti, Anderson Jose; Beskow, Arthur Bortolin; Silva, Cristiano Vitorino da [Universidade Regional Integrada do Alto Uruguai e das Missoes (URI), Erechim, RS (Brazil)], E-mails: arthur@uricer.edu.br, mlsperb@unisinos.br; Indrusiak, Maria Luiza Sperb [Universidade do Vale do Rio dos Sinos (UNISINOS), Sao Leopoldo, RS (Brazil)], E-mail: cristiano@uricer.edu.br

2010-07-01

This work presents a numerical study of the combustion process of leather residuals gasification gas, aiming the improvement of the process efficiency, considering different concentrations of water on the gas. The heating produced in this combustion process can be used to generation of thermal and/or electrical energy, for use at the leather industrial plant. However, the direct burning of this leather-residual-gas into the chambers is not straightforward. The alternative in development consists in processing this leather residuals by gasification or pyrolysis, separating the volatiles and products of incomplete combustion, for after use as fuel in a boiler. At these processes, different quantities of water can be used, resulting at different levels of moisture content in this fuel gas. This humidity can affect significantly the burning of this fuel, producing unburnt gases, as the carbon monoxide, or toxic gases as NOx, which must have their production minimized on the process, with the purpose of reducing the emission of pollutants to the atmosphere. Other environment-harmful-gases, remaining of the chemical treatment employed at leather manufacture, as cyanide, and hydrocarbons as toluene, must burn too, and the moisture content has influence on it. At this way, to increase understanding of the influence of moisture in the combustion process, it was made a numerical investigation study of reacting flow in the furnace, evaluating the temperature field, the chemical species concentration fields, flow mechanics and heat transfer at the process. The commercial CFD code CFX Ansys Inc. was used. Considering different moisture contents in the fuel used on the combustion process, with this study was possible to achieve the most efficient burning operation parameters, with improvement of combustion efficiency, and reduction of environmental harmful gases emissions. It was verified that the different moisture contents in the fuel gas demand different operation conditions

Study of tannery wastewater treatability by precipitation process

International Nuclear Information System (INIS)

Abbas, N.; Deba, F.; Iqbal, K.; Shafiq, T.; Ahmed, H.S.

2010-01-01

A study was conducted for the removal and recovery of chromium from tannery wastewater, using NaOH, MgO, Ca(OH)/sub 2/ and Al/sub 2/(SO/sub 4/)/sub 3/.18H/sub 2/O as precipitating agents and comparing their effect on pH, total dissolved solids (TDS), total suspended solids (TSS), sludge volume and chromium removal. MgO and Ca(OH)/sub 2/ produced least amount of sludge and dewatering of sludge was also easy as compared to Al/sub 2/(SO/sub 4/)/sub 3/.18H/sub 2/O and NaOH. The chromium removal of MgO and Ca(OH)/sub 2/ was 95% and 96%, respectively. (author)

Waste processing at tannery Royal Hulshof in Lichtenvoorde, Netherlands; Reststromen leerlooierij duurzaam verwerkt

Energy Technology Data Exchange (ETDEWEB)

De Jong, K [ed.

2005-02-01

The title tannery has put into operation a biological water purification insallation which not only operates in an efficient way, but also produces green gas and converts nitrogen compounds into nitrogen gas. [Dutch] Leerlooierij Koninklijke Hulshof in Lichtenvoorde nam onlangs een biologische waterzuivering in gebruik die niet alleen efficienter werkt, maar oo groen gas produceert en de stikstofverbindingen omzet in stikstofgas.

Use of Bentonite in residual waters of tanneries for the removal of Cr(III)

International Nuclear Information System (INIS)

Echavarria Isaza, Adriana; Moreno Casaf, Monica; Ramirez Ochoa, Claudia; Tamayo Martinez, Claudia; Saldarriaga Molina, Carlos

1998-01-01

An efficient procedure is reported for Cr(III) removal from tannery waste waters by means of natural and chemically treated bentonites. The best result was obtained using 20 mL of effluent with 7.5 grams of Bentonite. With this quantity it was removed the total amount of chromium III present in the sample

Correlation between bulk- and surface chemistry of Cr-tanned leather and the release of Cr(III) and Cr(VI).

Science.gov (United States)

Hedberg, Yolanda S; Lidén, Carola; Odnevall Wallinder, Inger

2014-09-15

About 1-3% of the adult general population in Europe is allergic to chromium (Cr). The assessment of the potential release of Cr(III) and Cr(VI) from leather is hence important from a human health and environmental risk perspective. The Cr(VI) content in leather was recently restricted in the European Union. The aim of this study was to assess possible correlations between the bulk and surface chemistry of leather, released Cr(III) and Cr(VI), and capacities of co-released leather specific species to reduce and complex released Cr. Four differently tanned leathers were characterized by scanning electron microscopy with energy dispersive spectroscopy, X-ray photoelectron spectroscopy, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, and the diphenylcarbazide colorimetric method. Their characteristics were compared with results on Cr(III) and Cr(VI) release into artificial sweat (ASW, pHleather-specific species were shown to reduce Cr(VI), both in ASW and in PB. Their reduction capacities correlated with findings of the surface content of Cr and of released Cr. Leather samples without this capacity, and with less aromatic surface groups visible by ATR-FTIR, revealed Cr(VI) both at the surface and in solution (PB). Copyright © 2014 The Authors. Published by Elsevier B.V. All rights reserved.

An evaluation of tannery industry wastewater treatment sludge gasification by artificial neural network modeling

International Nuclear Information System (INIS)

Ongen, Atakan; Kurtulus Ozcan, H.; Arayıcı, Semiha

2013-01-01

Highlights: • We model calorific value of syn-gas from tannery industry treatment sludge. • We monitor variation of gas composition in produced gas. • Heating value of produced gas is around 1500 kcal/m 3 . • Model predictions are in close accordance with real values. -- Abstract: This paper reports on the calorific value of synthetic gas (syngas) produced by gasification of dewatered sludge derived from treatment of tannery wastewater. Proximate and ultimate analyses of samples were performed. Thermochemical conversion alters the chemical structure of the waste. Dried air was used as a gasification agent at varying flow rates, which allowed the feedstock to be quickly converted into gas by means of different heterogeneous reactions. A lab-scale updraft fixed-bed steel reactor was used for thermochemical conversion of sludge samples. Artificial neural network (ANN) modeling techniques were used to observe variations in the syngas related to operational conditions. Modeled outputs showed that temporal changes of model predictions were in close accordance with real values. Correlation coefficients (r) showed that the ANN used in this study gave results with high sensitivity

An evaluation of tannery industry wastewater treatment sludge gasification by artificial neural network modeling

Energy Technology Data Exchange (ETDEWEB)

Ongen, Atakan, E-mail: aongen@istanbul.edu.tr; Kurtulus Ozcan, H.; Arayıcı, Semiha

2013-12-15

Highlights: • We model calorific value of syn-gas from tannery industry treatment sludge. • We monitor variation of gas composition in produced gas. • Heating value of produced gas is around 1500 kcal/m{sup 3}. • Model predictions are in close accordance with real values. -- Abstract: This paper reports on the calorific value of synthetic gas (syngas) produced by gasification of dewatered sludge derived from treatment of tannery wastewater. Proximate and ultimate analyses of samples were performed. Thermochemical conversion alters the chemical structure of the waste. Dried air was used as a gasification agent at varying flow rates, which allowed the feedstock to be quickly converted into gas by means of different heterogeneous reactions. A lab-scale updraft fixed-bed steel reactor was used for thermochemical conversion of sludge samples. Artificial neural network (ANN) modeling techniques were used to observe variations in the syngas related to operational conditions. Modeled outputs showed that temporal changes of model predictions were in close accordance with real values. Correlation coefficients (r) showed that the ANN used in this study gave results with high sensitivity.

Incineration of tannery sludge under oxic and anoxic conditions: study of chromium speciation.

Science.gov (United States)

Kavouras, P; Pantazopoulou, E; Varitis, S; Vourlias, G; Chrissafis, K; Dimitrakopulos, G P; Mitrakas, M; Zouboulis, A I; Karakostas, Th; Xenidis, A

2015-01-01

A tannery sludge, produced from physico-chemical treatment of tannery wastewaters, was incinerated without any pre-treatment process under oxic and anoxic conditions, by controlling the abundance of oxygen. Incineration in oxic conditions was performed at the temperature range from 300°C to 1200°C for duration of 2h, while in anoxic conditions at the temperature range from 400°C to 600°C and varying durations. Incineration under oxic conditions at 500°C resulted in almost total oxidation of Cr(III) to Cr(VI), with CaCrO4 to be the crystalline phase containing Cr(VI). At higher temperatures a part of Cr(VI) was reduced, mainly due to the formation of MgCr2O4. At 1200°C approximately 30% of Cr(VI) was reduced to Cr(III). Incineration under anoxic conditions substantially reduced the extent of oxidation of Cr(III) to Cr(VI). Increase of temperature and duration of incineration lead to increase of Cr(VI) content, while no chromium containing crystalline phase was detected. Copyright © 2014 Elsevier B.V. All rights reserved.

Pengaruh Penambahan Karagenan Terhadap Karakteristik Fisik, Kimia Dan Sensoris Fruit and Vegetable Leather Berbasis Albedo Semangka (Citrullus Vulgaris Schard.) Dan Labu Siam (Sechium Edule)

OpenAIRE

Haryu, Adinda Safira Puspa; Parnanto, Nur Her Riyadi; Nursiwi, Asri

2016-01-01

Penelitian ini bertujuan untuk mengetahui pengaruh penambahan karagenan terhadap karakteristik fisik, kimia dan sensorisdari fruit and vegetable leather berbasis albedo semangka dan labu siam. Pengolahan fruit leather yang ada di Indonesia saat inihanya berbahan dasar buah buahan, perlu adanya penganekaragaman olahan dari fruit leather ini dengan menambahkan sayuranuntuk meningkatkan kandungan serat dan gizi, yang selanjutnya dikenal sebagai fruit and vegetable leather. Penelitian inimengguna...

Production of basic chromium sulfate by using recovered chromium from ashes of thermally treated leather.

Science.gov (United States)

Dettmer, Aline; Nunes, Keila Guerra Pacheco; Gutterres, Mariliz; Marcílio, Nilson Romeu

2010-04-15

Leather wastes tanned with chromium are generated during the production process of leather, hence the wastes from hand crafted goods and footwear industries are a serious environmental problem. The thermal treatment of leather wastes can be one of the treatment options because the wastes are rich in chromium and can be used as a raw material for sodium chromate production and further to obtain several chromium compounds. The objective of this study was to utilize the chromium from leather wastes via basic chromium sulfate production to be subsequently applied in a hide tanning. The obtained results have shown that this is the first successful attempt to achieve desired base properties of the product. The result was achieved when the following conditions were applied: a molar ratio between sodium sulfite and sodium dichromate equal to 6; reaction time equal to 5 min before addition of sulfuric acid; pH of sodium dichromate solution equal to 2. Summarizing, there is an opportunity to utilize the dangerous wastes and reused them in the production scheme by minimizing or annulling the environmental impact and to attend a sustainable process development concept. 2009 Elsevier B.V. All rights reserved.

Reduction of turbidity and chromium content of tannery wastewater by electrocoagulation process.

Science.gov (United States)

2018-02-12

The present study is carried out to remove the chromium and turbidity from tannery wastewater by the electrocoagulationprocess with aluminum electrodes. This experimental study is performed using a batch system. The applied pilot comprises a reactor containing two parallel metal electrodes (Al). The latter are connected as mono polar and a different potential is applied between them. Several working parameters, such as applied potential difference, electrolysis time, active electrode surface, inter-electrode distance and pH of the medium have been studied to achieve higher removal efficiency.The treatment achieved a maximum reduction of 99% for the turbidity and 93% for the chromium under the following conditions: a potential difference: 15V; electrodes surface: 45cm2, inter-electrode distance: 1cm; raw water pH (6.1) and a contact time of 90 min. Considering the obtained efficiency in the present study, electrocoagulation process has the potential to be utilized for the cost-effective removal of pollutants from wastewater.

[Survival of Bacillus anthracis spores in various tannery baths].

Science.gov (United States)

Mendrycka, M; Mierzejewski, J

2000-01-01

The influence of tannery baths: liming, deliming, bating, pickling, tanning, retannage on the survival and on the germination dynamism of B. anthracis spores (Sterne strain) was investigated. The periods and the conditions of this influence were established according to technological process of cow hide tannage. Practically after every bath some part of the spores remained vital. The most effective killing of spores occurred after pickling, liming and deliming. Inversely, the most viable spores remained after bating and retannage process. The lack of correlation that was observed between survival and germination of spores after retannage bath can be explained by different mechanism of spores germination inhibition and their killing.

Biomethanization of tannery waste: An industrial experiment: Demonstration project. Biomethanisation de residus de tannerie: Une experience industrielle: Projet de demonstration

Energy Technology Data Exchange (ETDEWEB)

Aloy, M.; Mermet, R.; Sanejouand, J.

1988-01-01

The tanning and leather dressing industry produces large amounts of waste products including which can be placed in three categories: unrtanned waste, tanned waste, and liquid waste. Both untanned and liquid waste have a high organic content (proteins and fats) and their humidity levels are such that they are readily degraded by methanic fermentation. The results of the experiments confirm the technical feasibility of the project and indicate the economic limits of this type of plant. 14 figs.

Cleaner production for solid waste management in leather industry ...

African Journals Online (AJOL)

Cleaner production for solid waste management in leather industry. ... From the processes, wastes are generated which include wastewater effluents, solid wastes, and hazardous wastes. In developing countries including Ethiopia, many ... The solid waste inventory of the factory has been carried out. The major problems ...

Study of the dechroming of tanned leather wastes

Directory of Open Access Journals (Sweden)

Botić Tatjana

2004-01-01

Full Text Available According to European legislation, it is not possible to dump any chromium-containing waste in Europe. The minimization of wastes is a key element in that strategy. It involves the application of clean technologies: low and non-waste technologies. The tanning industry generates substantial quantities of chromium-containing solid waste in the form of shavings and trimmings. The recycling and reuse of those wastes must be the primary target in optimizing processes of the leather industry. The problem is in a satisfying chromium separation from collagen fibers. Common hydrolysis processes-alkaline or acidic-give gelatins containing residual chromium (III. By using an oxidation agent (H2O2 before alkaline hydrolysis, in was demonstrated that chromium from chromium-containing leather wastes can be almost fully recovered by the previous oxidation of Cr(III to Cr(VI. This chromium can be reused in the tanning process. That would represent an economic saving. The best result of the dechroming process was a gelatin hydrolyzate with only 1.11 in respect to the initial amount.

Spatial Agglomeration and Productivity of Textile and Leather Manufacturing in the Punjab Province of Pakistan

Directory of Open Access Journals (Sweden)

Asim Iqba

2013-05-01

Full Text Available This study investigates whether spatial agglomeration of textile and leather industry facilitates to enhance its own productivity at establishment level in the Punjab province of Pakistan. The empirical analysis is based on the survey data for the years 1995-96, 2000-2001 and 2005-06 collected from the Punjab Bureau of Statistics (PBS. The production function framework has been utilized. The results of production function suggest that spatial agglomeration of textile and leather industry plays a vital role in determining the productivity of establishments. The impact of localization (specialization is positive and stronger than urbanization (diversification which implies that locating manufacturing establishments in a particular district leads to enhance the productivity of establishments. Therefore, government policy should be biased to promote localization of textile and leather industry.

CO2 Separation and Capture Properties of Porous Carbonaceous Materials from Leather Residues

Directory of Open Access Journals (Sweden)

Ana Arenillas

2013-10-01

Full Text Available Carbonaceous porous materials derived from leather skin residues have been found to have excellent CO2 adsorption properties, with interestingly high gas selectivities for CO2 (α > 200 at a gas composition of 15% CO2/85% N2, 273K, 1 bar and capacities (>2 mmol·g−1 at 273 K. Both CO2 isotherms and the high heat of adsorption pointed to the presence of strong binding sites for CO2 which may be correlated with both: N content in the leather residues and ultrasmall pore sizes.

CO2 Separation and Capture Properties of Porous Carbonaceous Materials from Leather Residues

Science.gov (United States)

Bermúdez, José M.; Dominguez, Pablo Haro; Arenillas, Ana; Cot, Jaume; Weber, Jens; Luque, Rafael

2013-01-01

Carbonaceous porous materials derived from leather skin residues have been found to have excellent CO2 adsorption properties, with interestingly high gas selectivities for CO2 (α > 200 at a gas composition of 15% CO2/85% N2, 273K, 1 bar) and capacities (>2 mmol·g−1 at 273 K). Both CO2 isotherms and the high heat of adsorption pointed to the presence of strong binding sites for CO2 which may be correlated with both: N content in the leather residues and ultrasmall pore sizes. PMID:28788352

Production of the Allergenic Protein Alt a 1 by Alternaria Isolates from Working Environments

Directory of Open Access Journals (Sweden)

Justyna Skóra

2015-02-01

Full Text Available The aim of the study was to evaluate the ability of Alternaria isolates from workplaces to produce Alt a 1 allergenic protein, and to analyze whether technical materials (cellulose, compost, leather present within the working environment stimulate or inhibit Alt a 1 production (ELISA test. Studies included identification of the isolated molds by nucleotide sequences analyzing of the ITS1/ITS2 regions, actin, calmodulin and Alt a 1 genes. It has been shown that Alternaria molds are significant part of microbiocenosis in the archive, museum, library, composting plant and tannery (14%–16% frequency in the air. The presence of the gene encoding the Alt a 1 protein has been detected for the strains: Alternaria alternata, A. lini, A. limoniasperae A. nobilis and A. tenuissima. Environmental strains produced Alt a 1 at higher concentrations (1.103–6.528 ng/mL than a ATCC strain (0.551–0.975 ng/mL. It has been shown that the homogenization of the mycelium and the use of ultrafiltration allow a considerable increase of Alt a 1 concentration. Variations in the production of Alt a 1 protein, depend on the strain and extraction methods. These studies revealed no impact of the technical material from the workplaces on the production of Alt a 1 protein.

Health hazards of child labor in the leather products and surgical instrument manufacturing industries of Sialkot, Pakistan.

Science.gov (United States)

Junaid, Muhammad; Malik, Riffat Naseem; Pei, De-Sheng

2017-07-01

Child labor is a major challenge in the developing countries and comprehensive health hazard identification studies on this issue are still lacking. Therefore, the current study is an effort to highlight the health concerns of child labor exposed in the key small scale industries of Sialkot, Pakistan. Our findings revealed jolting levels of heavy metals in the urine, blood, serum, saliva, and hair samples collected from the exposed children. For example, in the urine samples, Cd, Cr, Ni, and Pb were measured at the respective concentrations of 39.17, 62.02, 11.94 and 10.53 μg/L in the surgical industries, and 2.10, 4.41, 1.04 and 5.35 μg/L in the leather industries. In addition, source apportionment revealed polishing, cutting, and welding sections in the surgical industries and surface coating, crusting, and stitching sections in the leather industries were the highest contributors of heavy metals in the bio-matrices of the exposed children, implying the dusty, unhygienic, and unhealthy indoor working conditions. Further, among all the bio-matrices, the hair samples expressed the highest bioaccumulation factor for heavy metals. In accordance with the heavy metal levels reported in the exposed children, higher oxidative stress was found in the children working in the surgical industries than those from the leather industries. Moreover, among heavy metals' exposure pathways, inhalation of industrial dust was identified as the primary route of exposure followed by the ingestion and dermal contact. Consequently, chemical daily intake (CDI), carcinogenic and non-carcinogenic hazard quotients (HQs) of heavy metals were also reported higher in the exposed children and were also alarmingly higher than the corresponding US EPA threshold limits. Taken all together, children were facing serious health implications in these industries and need immediate protective measures to remediate the current situation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chromium removal from tannery wastewater by using of flying ash

International Nuclear Information System (INIS)

Gil P, E.; Saldarriaga M, C.

1998-01-01

A simple and economic method to chromium removal from tannery wastewater by means of flying ash is presented. The chromium removal operation is a discontinuous process that involve the mass of flying ash, time of contact and temperature or ph as variables, their which are optimized through Box-Wilson type experimental design. The results were successful: From an initial fluid whit chromium concentration of 1850m ppm, final concentrations of 0.008 ppm and 0.5 ppm of Cr+3 and Cr+6 respectively were achieved. These post-treatment concentrations are into the approved range definite by Government's Laws to this waste type

DETERMINING LIGHTFASTNESS PROPERTIES OF VEGETABLE TANNINS AND CHEMICAL PROPERTIES OF THE LEATHERS TANNED WITH MODIFIED MIMOSA AND QUEBRACHO

Directory of Open Access Journals (Sweden)

OMUR Sukru

2016-05-01

Full Text Available The vegetable tannins are the oldest tanning agents used in leather industry. They give their natural character and colour to the leathers which they are applied to, but they have the disadvantage of colour change when they are exposed to light for prolonged times. In this study light fastness properties of leathers tanned with mimosa, quebracho, valonea and chestnut tannins were measured. Lightfastness properties of mimosa and quebracho tannins were found lower. Then these tannins were modified with sulphitation, novalac synthesis and sulphomethylation processes. Lightfastness and determination of volatile matter, determination of matter soluble in dichloromethane, determination of sulphated total ash and sulphated water-insoluble ash, determination of water soluble matter, water soluble inorganic matter and water soluble organic matter, determination of nitrogen content and hide substance, calculation of degree of tannage determination of formaldehyde content analyses were performed to the leathers tanned with modified mimosa and quebracho tannins. From comparison of results, it was understood that sulpmethylation process can be used for production of leathers with higher lightfastness and without major change on chemical properties. When chemical properties of leathers tanned with modified quebracho and mimosa are considered: volatile matter, sulphated total ash and sulphated water- insoluble ash, water soluble matter, water soluble inorganic matter and water soluble organic matter, hide substance and formaldehyde contents were found compatible with standard mimosa and quebracho. However degree of tannage and matter soluble in dichloromethane values were found lower, which means some enhancements in modification or fatliquoring process should be considered.

CONTRIBUTIONS TO CLASSIFICATION ZIPPERS USED IN INDUSTRY FOOTWEAR AND LEATHER GOODS

Directory of Open Access Journals (Sweden)

MALCOCI Marina

2016-05-01

Full Text Available Now customary accessory companies of all leather garments, zipper began to enjoy popularity only after 80 years of its invention. The first is considered the inventor of the zipper Elias Howe. Essentially involves fashion, change, innovation, originality, creativity and is defined as a succession of trends or fads, short. Create fashionable leather confections from home means accepting a contract with the producer and / or consumer, showing a profit motivating all at the right time. Continuous which require the exercise involves creative skills of fashion design, leading to a wide range of products. Current zipper is composed of: slider, teeth, strips shooter stops. Currently there is possibility to customize shooters to customer requirements, and even to form their own zippers. The present work presents the classification criteria zippers. They are after construction fastener after destination zippers, after the role they fulfill zippers, after the presentation at the procurement zippers, after finishing module of the metallic elements, as visibility zipper in the product, by type of teeth, by nature material strip zipper, after the type of materials they are made pullers, after the nature of the materials they are made of sliders and stops after the oxidation of metal components after finishing module teeth after shaped zipper, after slider type, by mode of ornamentation zippers. Knowing appearance zippers, elements of which it is composed, and their classification criteria allow us to correlate the shape of the product and destination.

Isolation and biochemical characterization of heavy-metal resistant bacteria from tannery effluent in Chittagong city, Bangladesh: Bioremediation viewpoint

Directory of Open Access Journals (Sweden)

Lolo Wal Marzan

2017-03-01

Full Text Available Toxic, mutagenic and carcinogenic heavy metals from tannery industries cause the pollution of agricultural environment and natural water sources. This study aims to isolate, investigate and identify naturally occurring bacteria capable of reducing and detoxifying heavy metals (Chromium, Cadmium and Lead from tannery effluent. Three isolates were identified up to genus level based on their morphological, cultural, physiological and biochemical characteristics as Gemella sp., Micrococcus sp. and Hafnia sp. Among them Gemella sp. and Micrococcus sp. showed resistance to Lead (Pb, chromium (Cr and cadmium (Cd, where Hafnia sp. showed sensitivity to cadmium (Cd. All isolates showed different MICs against the above heavy metals at different levels. Degrading potentiality was assessed using Atomic Absorption Spectrophotometer where Gemella sp. and Micrococcus sp. showed 55.16 ± 0.06% and 36.55 ± 0.01% reduction of Pb respectively. On the other hand, moderate degradation of Cd was shown by Gemella sp. (50.99 ± 0.01% and Micrococcus sp. (38.64 ± 0.06%. Heavy metals degradation capacity of Gemella sp. and Micrococcus sp. might be plasmid mediated, which might be used for plasmid transformation to transfer heavy metal accumulation capability. Therefore, identification of three bacteria for their heavy metal resistance and biodegradation capacity might be a base study to develop the production of potential local bioremediation agents in toxic tannery effluent treatment technology.

Physico-chemical analysis of tannery solid waste and structural characterization of its isolated humic acids after composting.

Science.gov (United States)

Amir, Soumia; Benlboukht, Fatima; Cancian, Nadia; Winterton, Peter; Hafidi, Mohamed

2008-12-30

In Marrakech, solid by-products from tanneries are highly polluting, generating large amounts of nitrogenous and organic matter. In the present study composting is tested as a cost-effective method for waste management to overcome many of the environmental hazards and produce a stable, rich material for soil fertilization. Two composting trials were conducted after neutralization by ammonia or lime. The aim of the neutralization was to avoid the antimicrobial effects of the acidity in the tannery waste, thus ensuring correct composting. Different techniques such as elemental analysis and 13C NMR spectroscopy were applied to analyse humic acids isolated from raw and composted materials, and to monitor the process of tannery waste composting, and the stability and maturity of the final product according to the means of neutralization. Comparison of data showed similar behaviour in both trials, but the composting process appeared to be more complete following neutralization with lime. The C, H and N content decreased, while the O increased. The FTIR and 13C NMR spectra show the decrease of aliphatic compounds demonstrated by the reduction of absorbance around 2922cm(-1) and of the resonance in the C-alkyl area around 0-55ppm. The humic acids newly formed during composting were richer in the O-N alkyl and oxidized aromatic structures that increased almost twofold on composting after neutralization with lime. The first principal component axis PC1 (54%) separated C-aliphatic, C-carboxylic and other less stable and less polycondensed compounds such as polyphenols from the more polycondensed O-N alkyl and oxidized C-aromatic compounds.

The preservative potentials of sweet orange seed oil on leather ...

African Journals Online (AJOL)

PRECIOUS

2010-02-01

Feb 1, 2010 ... The plant is found in China,. India, South America, Mexico, Africa, Australia and other countries. ... To produce protection on export of leather and for long ... Zaria and the open markets in Kano, Abraka and Lagos towns in.

The prevalence of chromium allergy in Denmark is currently increasing as a result of leather exposure

DEFF Research Database (Denmark)

Thyssen, J P; Jensen, P; Carlsen, B C

2009-01-01

BACKGROUND: Chromium allergy has traditionally been caused by occupational skin contact with cement. In 1983, Danish legislation made the addition of ferrous sulphate compulsory in cement to reduce the water-soluble chromium content to not more than 2 ppm. An effect from this intervention has pre...... leather exposure increased significantly from 24.1% during 1989-1994 to 45.5% during 1995-2007 (P leather exposure....

Boots of Leather, Slippers of Gold: The History of a Lesbian Community

Directory of Open Access Journals (Sweden)

Maria Chiara Ferro

2016-03-01

Full Text Available Elizabeth Lapovsky Kennedy, Madeline D. Davis, Boots of Leather, Slippers of Gold: The History of a Lesbian Community (1993. New York: Routledge, 2014.   La recensione sottolinea la rilevanza del volume Boots of Leather, Slippers of Gold a vent’anni dalla pubblicazione, sia perché raccoglie e preserva testimonianze di butches e femmes degli anni ’40 e ’50, sia perché chiarisce il ruolo sociale della comunità butch-femme in quanto sede di resistenza pre-politica. Inoltre, si evidenzia l’utilità di modelli interpretativi informati dagli studi queer e transgender nell’ambito della ricerca storica su identità non normative come quelle butch e femme.

Pengaruh Penambahan Jerami Nangka (Artocarpus heterophyllus Lam Terhadap Karakteristik Fruit Leather Mangga (Mangifera indica L

Directory of Open Access Journals (Sweden)

Lisa Yusmita

2018-04-01

Full Text Available ABSTRAK Penganekaragaman pangan merupakan program kebijakan pemerintah dengan tujuan untuk terus mengembangkan pangan agar dapat memantapkan kemandirian dan penyediaan pangan dengan jenis yang beragam dan kualitas yang makin meningkat, jumlah yang memadai dan tersebar merata sehingga dapat memenuhi kebutuhan pangan dan gizi. Untuk mendukung penganekaragaman pangan tersebut maka diperlukan upaya untuk melakukan pengolahan produk-produk hasil pertanian. Buah-buahan merupakan salah satu produk hasil pertanian yang umumnya dibuat menjadi produk olahan seperti jam, jelly, puree, sari buah, buah kaleng, manisan kering atau basah. Salah satu jenis produk buah-buahan yang kering selain manisan adalah fruit leather. Fruit leather adalah jenis makanan yang berasal dari daging buah yang telah dihancurkan dan dikeringkan. Produk ini berbentuk lembaran tipis seperti halnya kulit buah dengan tekstur yang plastis dan kenyal, rasanya manis tetapi masih memiliki ciri rasa khas buah yang digunakan. Fruit leather juga termasuk produk makanan yang tidak mengandung zat pewarna sehingga cocok untuk dijadikan cemilan dan mempunyai aneka ragam bentuk dan warna. Pengolahan buah-buahan menjadi fruit leather merupakan salah satu upaya divesifikasi pangan. Penelitian ini menggunakan metode Rancangan Acak Lengkap (RAL dengan 5 perlakuan dan 3 kali ulangan. Data yang diperoleh dianalisa secara statistik dengan uji F, kemudian bila berpengaruh nyata dilanjutkan dengan uji DNMRT pada taraf nyata 5%. Penelitian ini telah dilakukan di Laboratorium Program Studi Teknologi Industri Pertanian Universitas Dharma Andalas dan Laboratorium Teknologi Hasil Pertanian Fakultas Teknologi Pertanian Universitas Andalas. Dari hasil penelitian didapatkan kesimpulan bahwa konsentrasi penambahan jerami nangka berpengaruh nyata terhadap kadar vitamin C dan kadar serat kasar. Sementara untuk pengujian kadar air, total asam dan kadar gula ternyata tidak dipengaruhi oleh konsentrasi penambahan

IKEA: Global sourcing and sustainable leather initiatives

OpenAIRE

Jiang, Yan; Jia, Fu; Gong, Yu

2018-01-01

Aims: the aim of this teaching case is to illustrate the Sustainable Global Sourcing (SGS) practices of IKEA influenced by its Global Sourcing (GS) strategy and structure aspects through a case study of the sustainable leather initiative.Scope: this study is developed though 20 face-to-face interviews with IKEA managers in both Sweden and China, covering all the major SGS-related departments i.e. purchasing,sustainability, IWAY, and competence center (sustainable project team).Contribution: w...

Study on submerged anaerobic membrane bioreactor (SAMBR) treating high suspended solids raw tannery wastewater for biogas production.

Science.gov (United States)

Umaiyakunjaram, R; Shanmugam, P

2016-09-01

This study deals with the treatment of high suspended solids raw tannery wastewater using flat sheet Submerged Anaerobic Membrane (0.4μm) Bioreactor (SAMBR) acclimatized with hypersaline anaerobic seed sludge for recovering biogas. The treatability of SAMBR achieved higher CODremoval efficiency (90%) and biogas yield (0.160L.g(-1) CODremoved) coincided with high r(2) values between permeate flux and TSS (0.95), biogas and COD removed (0.96). The acidification of hypersaline influent wastewater by biogas mixing with high CO2, achieved quadruplet benefit of gas liquid and solid separation, in-situ pH and NH3 control, in-situ CH4 enrichment, and prevention of membrane fouling. The initial high VFA became stable as time elapsed reveals the hydrolysing ability of particulate COD into soluble COD and into biogas, confirms the suitability of SAMBR for high suspended solids tannery wastewater. Copyright © 2016 Elsevier Ltd. All rights reserved.

Extraction and Optimization of Natural Dye from Hambo Hambo (Cassia singueana Plant Used for Coloration of Tanned Leather Materials

Directory of Open Access Journals (Sweden)

Taame Berhanu

2017-01-01

Full Text Available This investigation was aimed at introducing natural dye extracted from the bark of Cassia Singueana plant for dyeing chrome tanned sheep skin crust leather. The colorant was extracted by aqueous extraction and its strength evaluated using UV-Visible spectroscopy. The extraction with the highest strength (3.9 at λmax of 400 nm was obtained at temperature of 95°C, concentration of 60 g/l, and time of 60 minutes. The possibility of using aloe vera juice and mango bark extract as natural mordants for leather coloration was investigated. Dyeing was conducted with and without mordant using different combinations of temperature, time, pH, and concentration of mordants. All three mordanting techniques were evaluated. The color strength (K/S, CIE L⁎a⁎b⁎ values, and fastness properties (light, rubbing, and perspiration of dyed leather samples were evaluated using appropriate instruments and according to international standards. Majority of samples exhibited that fastness result was in the range of good-excellent. Significantly better color fastness was obtained in case of leather samples premordanted with aloe vera. This study leads to the conclusion that dye extracted from bark of Cassia singueana can be used as colorant for tanned leather with the selected natural mordants.

Analysis of chromium status in the revegetated flora of a tannery waste site and microcosm studies using earthworm E. fetida.

Science.gov (United States)

Nirola, Ramkrishna; Megharaj, Mallavarapu; Subramanian, Avudainayagam; Thavamani, Palanisami; Ramadass, Kavitha; Aryal, Rupak; Saint, Christopher

2018-02-01

Chromium from tannery waste dump site causes significant environmental pollution affecting surrounding flora and fauna. The primary aims of this study were to survey vegetation, investigate the degree of soil pollution occurring near tannery waste dump site and make a systematic evaluation of soil contamination based on the chromium levels found in plants and earthworms from the impacted areas. This paper presents the pollution load of toxic heavy metals, and especially chromium, in 10 soil samples and 12 species of plants. Soil samples were analysed for heavy metals by using ICP-MS/ICP-OES method. Results indicated that Cr in soils exceeded soil quality guideline limits (SQGL). The total chromium present in the above ground parts of plants ranged from 1.7 mg kg -1 in Casuarina sp. to 1007 mg kg -1 in Sonchus asper. The Cr bioaccumulation in Eisenia fetida from tannery waste soil ranged from 5 to 194 mg kg -1 . The high enrichment factor of Cr in S. asper and bioaccumulation factor in earthworms indicate that there is a steady increase of toxic chromium risk in this area, which could be correlated with the past dumping activity. Emphasis needs to be put on control measures of pollution and remediation techniques in such areas to achieve an ecologically sustainable industrialisation.

Tannery and Duhem on the concept of a system in the history of philosophy and history of science

DEFF Research Database (Denmark)

Catana, Leo

2011-01-01

historical disciplines, creating the impression that they were mutually independent. Modern commentators have tended to take these declarations at face value. This article argues that Tannery and Duhem, some of the first historians of science, transferred historiographical concepts from history of philosophy...

Short-term social memory deficits in adult female mice exposed to tannery effluent and possible mechanism of action.

Science.gov (United States)

Estrela, Fernanda Neves; Rabelo, Letícia Martins; Vaz, Boniek Gontijo; de Oliveira Costa, Denys Ribeiro; Pereira, Igor; de Lima Rodrigues, Aline Sueli; Malafaia, Guilherme

2017-10-01

The accumulated organic residues in tannery-plant courtyards are an eating attraction to small rodents; however, the contact of these animals with these residues may change their social behavior. Thus, the aim of the present study is to investigate whether the exposure to tannery effluent (TE) can damage the social recognition memory of female Swiss mice, as well as to assess whether vitamin C supplementation could provide information about how TE constituents can damage these animals' memory. We have observed that resident females exposed to TE (without vitamin supplementation) did not explore the anogenital region, their body or chased intruding females for shorter time or with lower frequency during the retest session of the social recognition test, fact that indicates social recognition memory deficit in these animals. Such finding is reinforced by the confirmation that there was no change in the animals' olfactory function during the buried food test, or locomotor changes in females exposed to the pollutant. Since no behavioral change was observed in the females exposed to TE and treated with vitamin C (before or after the exposure), it is possible saying that these social cognitive impairments seem to be directly related to the imbalance between the cellular production of reactive oxygen species and the counteracting antioxidant mechanisms (oxidative stress) in female mice exposed to the pollutant (without vitamin supplementation). Therefore, the present study evidences that the direct contact with tannery effluent, even for a short period-of-time, may cause short-term social memory deficits in adult female Swiss mice. Copyright © 2017 Elsevier Ltd. All rights reserved.

The preservative potentials of sweet orange seed oil on leather ...

African Journals Online (AJOL)

Orange seed oil was extracted using the steam distillation method. The fungi isolated from the leather samples were Aspergillus niger, Aspergillus fumigatus, Aspergillus flavus, Paecilomyces sp., Penicillium sp., Rhizopus nigricans and Alternaria sp. However, the fungal species vary from person to person. The orange seed ...

Improvement in surface hydrophilicity and resistance to deformation of natural leather through O2/H2O low-temperature plasma treatment

Science.gov (United States)

You, Xuewei; Gou, Li; Tong, Xingye

2016-01-01

The natural leather was modified through O2/H2O low-temperature plasma treatment. Surface morphology was characterized by scanning electron microscopy (SEM) and the results showed that the pores on the leather surface became deeper and larger with enhanced permeability of water and vapor. XPS and FTIR-ATR was performed to determine the chemical composition of natural leather surface. Oxygen-containing groups were successfully grafted onto the surface of natural leather and oxygen content increased with longer treatment time. After O2/H2O plasma treatment, initial water contact angle was about 21° and water contact angles were not beyond 55° after being stored for 3 days. Furthermore, the tensile test indicated that the resistance to deformation had a prominent transform without sacrificing the tensile strength.

Pemanfaatan Buah Pepaya (Carica Papaya L.,) dan Tomat (Lycopersicum Esculentum Mill.,) dalam Pembuatan Fruit Leather

OpenAIRE

Ramli, Redi; Hamzah, Faizah

2017-01-01

This study aimed was to got exact formulation of combination of papaya fruit puree and tomato puree in the manufacture of fruit leather. This study used a completely randomized design (CRD) with 5 treatments and 3 replications. The treatments used against fruit leather were PT1 (papaya fruit puree 65%, tomato puree 35%), PT2 (papaya fruit puree 55%, tomato puree 45%), PT3 (papaya fruit puree 50%, tomato puree 50%), PT4 (45% papaya fruit puree, tomato puree 55%) and PT5 (35% papaya fruit puree...

Determination of Cr2O3 in chrome-tanned leather by radionuclide-excited X-ray fluorescence analysis

International Nuclear Information System (INIS)

Melich, M.; Palagyi, S.; Kern, M.

1989-01-01

Preliminary results on the determination of Cr 2 O 3 in chrome-tanned leather by measuring the content of Cr by means of radionuclide-excited XRF analysis are reported. For excitation a 3.7 GBq 238 Pu source was used and the characteristic K X-rays of Cr were detected with a planar Si(Li) detector. Both smooth and rough sides of the leather were analyzed directly or with a pair of V/Ti balanced filters. A fairly good correlation was found between Cr Kx counts of the rough side and the Cr 2 O 3 concentrations determined chemically in the range of 3.5 to 6.0% Cr 2 O 3 . The method renders possible a rapid and non-destructive determination of Cr 2 O 3 in various leather samples. (author)

A flux-enhancing forward osmosis-nanofiltration integrated treatment system for the tannery wastewater reclamation.

Science.gov (United States)

Pal, Parimal; Chakrabortty, Sankha; Nayak, Jayato; Senapati, Suman

2017-06-01

Effective treatment of tannery wastewater prior to discharge to the environment as per environmental regulations remains a big challenge despite efforts to bring down the concentrations of the pollutants which are often quite high as measured in terms of chemical oxygen demand (7800 mg/L), total dissolved solids (5400 mg/L), chloride (4260 mg/L), sulphides (250 mg/L) and chromium. A pilot-scale forward osmosis and nanofiltration integrated closed loop system was developed for continuous reclamation of clean water from tannery wastewater at a rate of 52-55 L/m 2 /h at 1.6 bar pressure. The low-cost draw solution was 0.8 M NaCl solution. Continuous recovery for recycling the draw solute was done by nanofiltration of diluted draw solution at an operating pressure of 12 bar and volumetric cross-flow rate of 700 L/h. Fouling study revealed that the specific flat-sheet design of cross-flow forward osmosis module with counter current flow of feed and draw solution prevents the build-up of concentration polarization, thus enabling long-term filtration in continuous mode of operation without significant membrane fouling. This study culminates in the development of a compact, efficient and low-cost industrial wastewater treatment and reclamation technology.

Laser-drilled micro-hole arrays on polyurethane synthetic leather for improvement of water vapor permeability

International Nuclear Information System (INIS)

Wu, Y.; Wang, A.H.; Zheng, R.R.; Tang, H.Q.; Qi, X.Y.; Ye, B.

2014-01-01

Three kinds of lasers at 1064, 532 and 355 nm wavelengths respectively were adopted to construct micro-hole arrays on polyurethane (PU) synthetic leather with an aim to improve water vapor permeability (WVP) of PU synthetic leather. The morphology of the laser-drilled micro-holes was observed to optimize laser parameters. The WVP and slit tear resistance of the laser-drilled leather were measured. Results show that the optimized pulse energy for the 1064, 532 and 355 nm lasers are 0.8, 1.1 and 0.26 mJ, respectively. The diameters of the micro-holes drilled with the optimized laser pulse energy were about 20, 15 and 10 μm, respectively. The depths of the micro-holes drilled with the optimized pulse energy were about 21, 60 and 69 μm, respectively. Compared with the untreated samples, the highest WVP growth ratio was 38.4%, 46.8% and 53.5% achieved by the 1064, 532 and 355 nm lasers, respectively. And the highest decreasing ratio of slit tear resistance was 11.1%, 14.8%, and 22.5% treated by the 1064, 532 and 355 nm lasers, respectively. Analysis of the interaction mechanism between laser beams at three kinds of laser wavelengths and the PU synthetic leather revealed that laser micro-drilling at 355 nm wavelength displayed both photochemical ablation and photothermal ablation, while laser micro-drilling at 1064 and 532 nm wavelengths leaded to photothermal ablation only.

Laser-drilled micro-hole arrays on polyurethane synthetic leather for improvement of water vapor permeability

Science.gov (United States)

Wu, Y.; Wang, A. H.; Zheng, R. R.; Tang, H. Q.; Qi, X. Y.; Ye, B.

2014-06-01

Three kinds of lasers at 1064, 532 and 355 nm wavelengths respectively were adopted to construct micro-hole arrays on polyurethane (PU) synthetic leather with an aim to improve water vapor permeability (WVP) of PU synthetic leather. The morphology of the laser-drilled micro-holes was observed to optimize laser parameters. The WVP and slit tear resistance of the laser-drilled leather were measured. Results show that the optimized pulse energy for the 1064, 532 and 355 nm lasers are 0.8, 1.1 and 0.26 mJ, respectively. The diameters of the micro-holes drilled with the optimized laser pulse energy were about 20, 15 and 10 μm, respectively. The depths of the micro-holes drilled with the optimized pulse energy were about 21, 60 and 69 μm, respectively. Compared with the untreated samples, the highest WVP growth ratio was 38.4%, 46.8% and 53.5% achieved by the 1064, 532 and 355 nm lasers, respectively. And the highest decreasing ratio of slit tear resistance was 11.1%, 14.8%, and 22.5% treated by the 1064, 532 and 355 nm lasers, respectively. Analysis of the interaction mechanism between laser beams at three kinds of laser wavelengths and the PU synthetic leather revealed that laser micro-drilling at 355 nm wavelength displayed both photochemical ablation and photothermal ablation, while laser micro-drilling at 1064 and 532 nm wavelengths leaded to photothermal ablation only.

Using Leather Puppets as Local Wisdom Based Learning Mediafor Teaching the Material of Heredity of the Natural Sciencessubject for Grade IX Students

OpenAIRE

Rakhmawati, Yesi; Apriliani, Putri; Wulansari, Merya

2013-01-01

The objectives of this study were (1) to reveal the improvement of students'understanding about heredity by using the media of leather puppets, and (2) to findout the use of leather puppets as learning media for teaching heredity to the grade IXstudents.The method used in this study was quasi experiment post test only. The subjectand object of this study were leather puppets as learning media of heredity at gradeIX and the improvement of the students' understanding about the heredity. About 2...

Distribution and Potential Mobility of Selected Heavy Metals in a Fluvial Environment Under the Influence of Tanneries

Directory of Open Access Journals (Sweden)

Rodrigues M. L. K.

2013-04-01

Full Text Available In this study we evaluated the occurrence of heavy metals in a fluvial environment under the influence of tanneries – the Cadeia and Feitoria rivers basin (RS, south Brazil, highlighting the distribution and potential mobility of the selected elements. Every three months, over one year-period, selected heavy metals and ancillary parameters were analyzed in water and sediment samples taken at ten sites along the rivers. Water analyses followed APHA recommendations, and sediment analyses were based on methods from USEPA (SW846 and European Community (BCR sequential extraction. The determinations were performed by ICP/OES, except for Hg (CV/ETA. Statistical factor analysis was applied to water and sediment data sets, in order to obtain a synthesis of the environmental diagnosis. The results revealed that water quality decreased along the rivers, and mainly on the dry period (January, showing the influence of tannery plants vicinity and flow variations. Except for Fe, Al, and eventually Mn, heavy metal contents in water were in agreement with Brazilian standards. Concerning sediments, Al, Cu, Fe, Ni, Mn, Ti, and Zn concentrations appeared to reflect the base levels, while Cr and Hg were enriched in the deposits from the lower part of the basin. The partition of heavy metals among the sediment geochemical phases showed higher mobility of Mn along the sampling sites, followed by Cr in the lower reach of the basin, most affected by tanneries. Since Cr was predominantly associated to the oxidizable fraction, its potential mobilization from contaminated sediments would be associated to redox conditions. The detection of Hg in the tissue of a bottom-fish species indicated that the environmental conditions are apparently favoring the remobilization of this metal from contaminated sediments.

Fluctuations in the prevalence of chromate allergy in Denmark and exposure to chrome-tanned leather.

Science.gov (United States)

Carøe, Caroline; Andersen, Klaus E; Thyssen, Jacob P; Mortz, Charlotte G

2010-12-01

A recent Danish study showed a significant increase in the prevalence of chromate contact allergy after the mid-1990s, probably as a result of exposure to leather products. To reproduce the results by analysing data from the period 1992-2009 at Odense University Hospital, Denmark. The temporal development in the occurrence of chromate contact allergy and assumed causative exposures were investigated. A retrospective analysis of patch test data was performed (n = 8483), and medical charts from patients with chromate allergy (n = 231) were reviewed. Comparisons were made using the χ(2) -test. A test of the reproducibility of the TRUE Test® was also performed. Logistic regression analyses were used to test for associations. No significant changes in the prevalence or exposure sources of chromate allergy during 1992-2009 were identified. Leather shoes (24.4%) were the most frequent exposure sources in chromate allergy, and were mainly registered in women, although the difference between men and women was not significant (P = 0.07). Cement and leather glove exposure occurred significantly more often in men than in women (P = 0.002). Foot dermatitis (40.3%) was the most frequent anatomical location, apart from hand eczema (60.6%). The reproducibility of the TRUE Test® was 93.3%. Apart from hand eczema, the most frequent clinical picture of chromate allergy was foot dermatitis caused by leather shoe exposure. A tendency for an increasing prevalence of chromate contact allergy from 1997 was shown, but no significant change was detectable. © 2010 John Wiley & Sons A/S.

Abundance and diversity of bacterial nitrifiers and denitrifiers and their functional genes in tannery wastewater treatment plants revealed by high-throughput sequencing.

Directory of Open Access Journals (Sweden)

Zhu Wang

Full Text Available Biological nitrification/denitrification is frequently used to remove nitrogen from tannery wastewater containing high concentrations of ammonia. However, information is limited about the bacterial nitrifiers and denitrifiers and their functional genes in tannery wastewater treatment plants (WWTPs due to the low-throughput of the previously used methods. In this study, 454 pyrosequencing and Illumina high-throughput sequencing, combined with molecular methods, were used to comprehensively characterize structures and functions of nitrification and denitrification bacterial communities in aerobic and anaerobic sludge of two full-scale tannery WWTPs. Pyrosequencing of 16S rRNA genes showed that Proteobacteria and Synergistetes dominated in the aerobic and anaerobic sludge, respectively. Ammonia-oxidizing bacteria (AOB amoA gene cloning revealed that Nitrosomonas europaea dominated the ammonia-oxidizing community in the WWTPs. Metagenomic analysis showed that the denitrifiers mainly included the genera of Thauera, Paracoccus, Hyphomicrobium, Comamonas and Azoarcus, which may greatly contribute to the nitrogen removal in the two WWTPs. It is interesting that AOB and ammonia-oxidizing archaea had low abundance although both WWTPs demonstrated high ammonium removal efficiency. Good correlation between the qPCR and metagenomic analysis is observed for the quantification of functional genes amoA, nirK, nirS and nosZ, indicating that the metagenomic approach may be a promising method used to comprehensively investigate the abundance of functional genes of nitrifiers and denitrifiers in the environment.

PVC-based synthetic leather to provide more comfortable and sustainable vehicles

Science.gov (United States)

Maia, I.; Santos, J.; Abreu, MJ; Miranda, T.; Carneiro, N.; Soares, GMB

2017-10-01

Consumers are increasingly demanding the interior of cars to be comfortable even in the case of more economic commercial segments. Thus, the development of materials with thermoregulation properties has assumed renewed interest for these particular applications. An attempt has been made to prepare a multilayer PVC-based synthetic leather with paraffinic PCMs to be applied on a car seat. The thermal behaviour of the material was analysed using Alambeta apparatus, a thermo-camera and a thermal manikin. The results obtained show that the synthetic leather with incorporated PCMs gives cooler feeling and has higher reaction times regarding environmental temperature variations than the material without PCMs incorporation. Globally, the new designed material allowed greater thermal comfort to the cars´ inhabitants. In addition, the material quality was evaluated according to the standard of the customer, BMW 9,210,275; Edition / Version 4, 2010-10-01 revealing that the material meets all the requirements under test, except for the performance in terms of flexibility.

Development of a Method for the Determination of Chromium and Cadmium in Tannery Wastewater Using Laser-Induced Breakdown Spectroscopy

Directory of Open Access Journals (Sweden)

Mahwish Bukhari

2012-01-01

Full Text Available This paper illustrates systematic development of a convenient analytical method for the determination of chromium and cadmium in tannery wastewater using laser-induced breakdown spectroscopy (LIBS. A new approach was developed by which liquid was converted into solid phase sample surface using absorption paper for subsequent LIBS analysis. The optimized values of LIBS parameters were 146.7 mJ for chromium and 89.5 mJ for cadmium (laser pulse energy, 4.5 μs (delay time, 70 mm (lens to sample surface distance, and 7 mm (light collection system to sample surface distance. Optimized values of LIBS parameters demonstrated strong spectrum lines for each metal keeping the background noise at minimum level. The new method of preparing metal standards on absorption papers exhibited calibration curves with good linearity with correlation coefficients, R2 in the range of 0.992 to 0.998. The developed method was tested on real tannery wastewater samples for determination of chromium and cadmium.

Spectral imaging of Dutch gilt leather for improved conservation strategies

NARCIS (Netherlands)

Papadakis, V.; Posthuma de Boer, M.; Mkhoyan, T.; van Velzen, B; Seymour, K.; Groves, R.M.

2016-01-01

Gilt leather was one of the most fashionable and costly types of wall hangings in the Western world in the 16th to 18th centuries. Despite its appearance, it is not real gold that creates the golden shine, but typically a silver leaf which is coated with an orange-brown lacquer to obtain a golden

Preparation and Consumer Acceptance of Indian Mango Leather and Osmo - Dehyrated Indian Mango

Directory of Open Access Journals (Sweden)

Cyril John A. Domingo

2017-05-01

Full Text Available Indian mangoes are considered highly perishable products due to high moisture content which resulted in high postharvest losses in Pangasinan, Philippines. This study exploits the potential of underutilized indian mango to value - added products. The developed i ndian mango leather and osmo - dehyrated indian mango are deh ydrated fruit products can be eaten as snacks or desserts. Indian mango leathe r was prepared by mixing fruit puree and other additives like sugar, citric acid, and sodium met abisulphite and then dehydrated them at 55 °C for 15 hours under convective oven. Osmo - dehydrated indian mang o was prepared by immer sing h alves of deseeded and deskinned pulps in 50 % (w/w sucrose solution for 20 hours f ollowed by drying initially at 50 °C then aft er one hour at 60 °C for 15 hours. Thirty - three member untrained panels were involved in consumer a ccep tance evaluation . Panelists evaluated the colo r, sweetness, sourness, texture, and overall acceptability of the osmotically - treated indian mango and indian mango leather using seven - point h edonic scale . Over - all, the indian mango leather and osmo - dehy drated indian mango developed in this study seemed to be acceptable for all the sensory parameters as indicated by high scores of greater than five (>5 .

Particulate COD balance of particulate cod in eletrocuagulation/flotation reactor treating tannery effluent

Directory of Open Access Journals (Sweden)

Rodrigo Babora Borri

2012-04-01

Full Text Available Mass balance or particulate organic matter was studied in terms of COD, by means of electrocoagulation/flotation (ECF reactor treating tannery effluent. Reactor was operated in fill and draw (batch mode. Operating in hydraulic residence time of 65 minutes, ECF reactor reached 55 % COD removal. Although volatile solids were also removed from liquid phase (removal of 40%, fixed solids concentration, and hence total solids concentration, showed to be higher in withdrawn effluent than in ECF’s influent. This was assigned to NaCl added in order to enhance conductivity in wastewater.

Characteristics of the chrome-tanned sheep leather treated by radiation-induced graft of BA

International Nuclear Information System (INIS)

Zhou Dezhong; Deng Yongzhen; Li Ying

1986-01-01

The characteristics of the chrome-tanned sheep leather treated by radiation-induced graft of BA is presented. Using the method of radiation-induced graft of BA instead of the chrome-retanning, the leather has been obviously improved not only in the surface, such as the brightness, fullness, uniformity of the thickness but also in the physical characteristics such as retaining of tensile strength, decreasing of water absorption after being immersed in water for 2h, and 24h, enhancement of tearing strength and stitch tear strength. Although the air permeability and water vapor permeability are a bit worse than the control, however is still in the range of the standard issued by Light Industry Ministry of China

Chromium fate in constructed wetlands treating tannery wastewaters.

Science.gov (United States)

Dotro, Gabriela; Palazolo, Paul; Larsen, Daniel

2009-06-01

Nine experimental wetlands were built to determine chromium partitioning inside systems treating tannery wastewaters. Results showed 5-day biochemical oxygen demand and chromium removals of 95 to 99% and 90 to 99%, respectively. The majority of chromium was found in association with media (96 to 98%), followed by effluents (2.9 to 3.9%), and the least was found in plant parts (0.1%). Chemical speciation modeling of solutions and scanning electron microscope analysis suggest two potential chromium removal mechanisms--sorption/coprecipitation with iron hydroxides or oxyhydroxides and biomass sorption. The release of the majority of chromium in the iron- and organic-bound phases during sequential extractions supports the proposed dominant removal mechanisms. The use of a mixture of peat and gravel resulted in lower removal efficiencies and stronger partitioning in organic phases during sequential extractions. Chromium was efficiently removed by wetlands, retained through chemical and biological processes. Future research will focus on further exploring removal mechanisms and proposing management strategies for the chromium-containing wetland media.

Electrocoagulation efficiency of the tannery effluent treatment using aluminium electrodes.

Science.gov (United States)

Espinoza-Quiñones, Fernando R; Fornari, Marilda M T; Módenes, Aparecido N; Palácio, Soraya M; Trigueros, Daniela E G; Borba, Fernando H; Kroumov, Alexander D

2009-01-01

An electro-coagulation laboratory scale system using aluminium plates electrodes was studied for the removal of organic and inorganic pollutants as a by-product from leather finishing industrial process. A fractional factorial 2(3) experimental design was applied in order to obtain optimal values of the system state variables. The electro-coagulation (EC) process efficiency was based on the chemical oxygen demand (COD), turbidity, total suspended solid, total fixed solid, total volatile solid, and chemical element concentration values. Analysis of variance (ANOVA) for final pH, total fixed solid (TFS), turbidity and Ca concentration have confirmed the predicted models by the experimental design within a 95% confidence level. The reactor working conditions close to real effluent pH (7.6) and electrolysis time in the range 30-45 min were enough to achieve the cost effective reduction factors of organic and inorganic pollutants' concentrations. An appreciable improvement in COD removal efficiency was obtained for electro-coagulation treatment. Finally, the technical-economical analysis results have clearly shown that the electro-coagulation method is very promising for industrial application.

Utilization of tannery fleshings: Optimization of conditions for fermenting delimed tannery fleshings using Enterococcus faecium HAB01 by response surface methodology.

Science.gov (United States)

Kumar Rai, Amit; General, Thiyam; Bhaskar, N; Suresh, P V; Sakhare, P Z; Halami, P M; Gowda, Lalitha R; Mahendrakar, N S

2010-03-01

Conditions for fermentation of delimed tannery fleshings--to obtain higher degree of protein hydrolysis and reasonably better antioxidant activity--using Enterococcus faecium HAB01 (GenBank #FJ418568) were optimized. Three independent variables--viz., inoculum level (X1), glucose level (X2) and fermentation time (X3)--were optimized using response surface method considering degree of hydrolysis (DH; %) and total titrable acidity (TTA) as response variables. The optimized conditions were found to be 12.5% (v/w) inoculum, 17.5% (w/w) glucose and 96h of fermentation at 37+/-1 degrees C to obtain a maximum DH%. The usefulness of the predicted model was further validated by considering random combinations of the independent factors. The chemical score of the hydrolysate revealed an excess amount of essential amino acids, viz., arginine and leucine compared to reference protein. The liquor portion had relatively high antioxidant activities, indicating its potential for use as a high value feed ingredient. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Improvement in surface hydrophilicity and resistance to deformation of natural leather through O_2/H_2O low-temperature plasma treatment

International Nuclear Information System (INIS)

You, Xuewei; Gou, Li; Tong, Xingye

2016-01-01

Graphical abstract: - Highlights: • O_2/H_2O can increase oxygen concentration in the plasma compared to the pure O_2 atmosphere. • Pores at the surface of natural leather became larger and deeper with enhanced permeability of water. • The initial water contact angle was about 21°. • Its preferable surface hydrophilicity kept for 3 days, which gives guidance for next process. • The elongation of the treated sample for 10 min was twice as large as that of the untreated sample. - Abstract: The natural leather was modified through O_2/H_2O low-temperature plasma treatment. Surface morphology was characterized by scanning electron microscopy (SEM) and the results showed that the pores on the leather surface became deeper and larger with enhanced permeability of water and vapor. XPS and FTIR-ATR was performed to determine the chemical composition of natural leather surface. Oxygen-containing groups were successfully grafted onto the surface of natural leather and oxygen content increased with longer treatment time. After O_2/H_2O plasma treatment, initial water contact angle was about 21° and water contact angles were not beyond 55° after being stored for 3 days. Furthermore, the tensile test indicated that the resistance to deformation had a prominent transform without sacrificing the tensile strength.

A comparison of leather properties of skins from ten different South ...

African Journals Online (AJOL)

Unknown

Short paper and poster abstracts: 38th Congress of the South African Society of Animal Science. The South African Journal of Animal Science is available online at http://www.sasas.co.za/Sajas.html. 130. Table 1 Physical test results (SE) of leather produced from different sheep skins. Breed. Tensile strength. (Mpa).

The Use Level of Chrome Tannage For Rabbit Fur Leather Observed on Tearing Strength, Stitch Tearing Strength, Water Absorption and Organoleptic

Directory of Open Access Journals (Sweden)

Mustakim Mustakim

2012-02-01

Full Text Available The purpose of this study was to find out the appropiate of chrome tannage level for rabbit fur leather quality. The result were expected to contribute information for many people who relate with tanning technology, especialy about the use level of chrome tannage for fur leather quality and could as patern to hold further research.The material that used were 12 pieces of three months of rabbit skin. The method is Completely Randomized Design, consist of three treatments of chrome tannage (Chromosal B, they were : B1 (Chromosal B 6%, B2 (Chromosal B 8%, and B3 (Chromosal B 10%. Each of treatment hold on four replications. The variables which measured are tearing strength, stitch teraing strength, water absorption and organoleptic consist of “kekuatan bulu”’ “kerataan bulu” and “kelemasan kulit” in fur leather. Data was analysed by analysis variance followed by Duncan’s Multiple Range Test. The result of this research show that the use level of chromosal B give very significant influence among tearing strength, stitch tearing strength and water absorption. It gave significant influence among the organoleptic test. Based on the result, can be concluded that 10 percent of chrome tannage (chromosal B, produce the best result on tearing strength, stitch tearing strength, water absorption and organoleptic for “kekuatan bulu” and “kerataan bulu”. The incrase of chrome tannage offer will decrease the “kelemasan kulit” in fur leather and the best “kelemasan kulit” produced by the lowest chrome tannage offer, that was 6 percent of Chromosal B. The best quality of rabbit fur leather produced by 10 percent of chrome tannage offer.   Keywords: chrome, tannage, fur leather

[Treatment of tannery wastewater by infiltration percolation: chromium removal and speciation in soil].

Science.gov (United States)

Tiglyene, S; Jaouad, A; Mandi, L

2008-06-01

The aim of this paper was, on one hand, to study the treatment of raw tannery effluent by infiltration percolation system and, on the other hand, to determine the distribution and speciation of chromium in the used soil. The system pilot consisted of columns filled to 15 cm of gravel and 60 cm of soil (88% of sand). The columns irrigated by raw tannery wastewater with a daily hydraulic load of 5 cm per day (approximately 10 L every day). The water flowed vertically through the soil. The speciation of Cr was investigated by using selective five steps sequential extraction method. The results indicated that the pH of the treated wastewater increases by three units in comparison to the raw wastewater. The electrical conductivity of the effluent increases also after treatment. Over the whole experimental period, results revealed significant performances of infiltration percolation system for organic load reduction. The mean elimination rate was 74% for total COD. In addition, there was a significant accumulation of organic carbon (62%) in the surface strata for the system. The total chromium undergoes an overall removal of 98%. After seven months of experiment, the results indicated that the whole retention of Cr occurring in the surface horizon of the soil (69%). Furthermore, the speciation study of Cr in the soil revealed that the oxidizable fraction is the most represented 55%. The reducible and residual phases represent 17.5% and 18.5%, respectively. The carbonate fraction presented 9% while exchangeable fraction presented only 0.02%.

Formulation and acceptability of foam mat dried seabuckthorn (Hippophae salicifolia) leather.

Science.gov (United States)

Kaushal, Manisha; Sharma, P C; Sharma, Rakesh

2013-02-01

Technology for utilization of seabuckthorn berries for preparation of fruit leather/bar was optimized by modifying the foam mat drying technique. The conversion of seabuckthorn juice/pulp into foam was standardized by whipping the pulp after addition of CMC @ 0-3% at 5 °C and drying the resultant foam in dehydrator (55 ± 2 °C) to a moisture content of about 12-14%. The fruit bar prepared from sulphited juice/pulp wrapped in a butter paper followed by packing in polyethylene pouches (20 g) and stored at ambient temperature (14.6-26.1 °C) experienced least changes in quality attributes like ascorbic acid (1045.7 mg/100 g vs 997.5 mg/100 g) and carotenoids (80.4 mg/100 g vs 72.3 mg/100 g) as compared to the leather made from the unsulphited pulp. Storage studies indicate that fruit bars are mildly hygroscopic (0.46-0.65) and can be stored within the RH of 46-65% at room temperature.

Adsorption of basic chromium sulfate used in the tannery industries by calcined hydrotalcite

International Nuclear Information System (INIS)

Lopez M, B. E.; Rivera R, R.; Iturbe G, J. L.; Olguin G, M. T.

2011-01-01

The sorption behavior of the chemical species of Cr(III) from aqueous solutions by hydrotalcite calcined products was investigated considering the equilibrium ph (5.0 to 8.9) and the chromium concentration in aqueous solution (from 10.6 to 430.0 mmol/L) to obtain the corresponding isotherms. Each solution was prepared from basic Cr(III) sulphate which is a primary tanning agent used in the tannery industries. In this work no previous oxidation treatment was done to form Cr(vi) in order to remove the chromium from aqueous solutions by hydrotalcite. The amount of chromium in the remaining solutions after the sorption processes in a batch system by visible spectroscopy (Vis) was determined. The calcined hydrotalcite before and after the contact with the chromium(III) solutions by X-ray power diffraction, thermogravimetric analysis and Fourier transformed infrared spectroscopy, were characterized. The specific are by Brunauer, Emmett and Teller (Bet) method of each sample was also evaluated. It was found that under the experimental conditions of this work hydrolyzed species of Cr(III) are precipitated on the surface of the calcined hydrotalcite instead other adsorption mechanism, and the sulfate ions were the responsible to regenerated the crystalline structure of hydrotalcite, therefore the results are discussed in terms of both Cr(III) and sulfate chemical species. (Author)

Adsorption of basic chromium sulfate used in the tannery industries by calcined hydrotalcite

Energy Technology Data Exchange (ETDEWEB)

Lopez M, B. E.; Rivera R, R.; Iturbe G, J. L.; Olguin G, M. T., E-mail: beatriz.lopez@inin.gob.mx [ININ, Departamento de Quimica, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2011-07-01

The sorption behavior of the chemical species of Cr(III) from aqueous solutions by hydrotalcite calcined products was investigated considering the equilibrium ph (5.0 to 8.9) and the chromium concentration in aqueous solution (from 10.6 to 430.0 mmol/L) to obtain the corresponding isotherms. Each solution was prepared from basic Cr(III) sulphate which is a primary tanning agent used in the tannery industries. In this work no previous oxidation treatment was done to form Cr(vi) in order to remove the chromium from aqueous solutions by hydrotalcite. The amount of chromium in the remaining solutions after the sorption processes in a batch system by visible spectroscopy (Vis) was determined. The calcined hydrotalcite before and after the contact with the chromium(III) solutions by X-ray power diffraction, thermogravimetric analysis and Fourier transformed infrared spectroscopy, were characterized. The specific are by Brunauer, Emmett and Teller (Bet) method of each sample was also evaluated. It was found that under the experimental conditions of this work hydrolyzed species of Cr(III) are precipitated on the surface of the calcined hydrotalcite instead other adsorption mechanism, and the sulfate ions were the responsible to regenerated the crystalline structure of hydrotalcite, therefore the results are discussed in terms of both Cr(III) and sulfate chemical species. (Author)

The effect of mimosa and syntan mixture on the quality of tanned red snapper leather

Science.gov (United States)

Pratama, M.; Sahubawa, L.; Pertiwiningrum, A.; Rahmadian, Y.; Puspita, I. D.

2018-03-01

This study aimed to determine the effect of syntan and mimosa combination on the quality of tanned red snapper leather. The study was designed using complete randomized design (CRD) and the advanced test of Least Significant Difference (LSD) with three replications and three treatments of combined syntan and mimosa, namely: p1 (4 % syntan, 5 % mimosa), p2 (8 % syntan, 5 %mimosa), p3 (12 % syntan, 5 % mimosa). Data were analyzed using SPSS 18. The measured parameters were tensile strength (N·cm-2), elongation (%), tear strength (N·cm-1), enervation (mm), wrinkle temperature (°C), fat/oil content (%) and water content (%). The results indicate that the combined syntan and mimosa tanners gave no significant effect on the physical parameters (tensile strength, elongation, tear strength, enervation and wrinkle temperature) and chemical parameters (moisture and fat/oil). All treatments (p1, p2 and p3) met the Indonesian National Standard (SNI) 06-4586-1998 for chrome tanned freshwater snake leather for the parameters of tensile strength, tear strength, enervation, wrinkle temperature and moisture. The parameter of elongation and fat/oil content did not meet with the SNI 06-4586-1998. Among the three combinations of a tanner, syntan 4 % and mimosa 5 % treatment gave the best leather quality.

BIOSORPSI DAN REDUKSI KROM LIMBAH PENYAMAKAN KULIT DENGAN BIOMASSA Fusarium sp DAN Aspergillus niger (Biosorpstion and Reduction of Chromium Bearing Tannery Wastewater Using The Biomass of Fusarium Sp. and Aspergillus niger

Directory of Open Access Journals (Sweden)

Suharjono Triatmojo

2001-08-01

Full Text Available ABSTRAK Tujuan penelitian ini ialah untuk membuktikan bahwa biomassa Fusarium sp dapat mereduksi Cr(VI, dan biomassa Aspergillus niger dapat digunakan untuk mengambil ion krom dari larutan. Fusarium.sp ditumbuhkan pada media cair kentang dekftosa cair, ditambah K2Cr2O7 atau sludge limbah penyamakan kulit. Selanjutnya diamati perubahan warnanya, bila terjadi perubahan warna dan oranye ke ungu atau tak berwarna maka telah terjadi reduksi krom valensi VI menjadi krom valensi Ill. Aspergillus niger ditumbuhkan pada media Potato dectrose agar (PDA padat, dipindahkan ke media cair yang bensi bakto pepton, bakto dektrose dan srukronutrien. Produksi biomassa dilakukan pada labu erlenmeyer; setelah 5 hari dipanen dan dibuat bubuk. Bubuk ini digunakan untuk mengambil krom dari larutan. Hasil penelitian menunjukkan bahwa biomassa Fusarium sp dapat digunakan untuk mengambil krom dan larutan yang.mengandung KrCrrO, atau sludge limbah penyamakan kulit. Waktu inkubasi yang lebih lama meningkatkan absorbsi krom oleh biomassa Fascrium sp. Fusarium sp mampu mereduksi Cr(VI menjadi Cr(Iii. Biomassa Aspergillus niger dapat digunakan untuk mengambil krom dari larutan. Hasil terbaik diperoleh pada konsentrasi awal 100 mg/I, pada pH 2,0, berat biomassa 0,1 g, dan waktu kontak 12 jam, yaitu 96,23% untuk Cr(II| dan96,3 % untuk Cr(VI. Fusarium sp. dan A. niger dapat digunakan sebagai bioremediator dalam penanganan limbah penyamakan kulit secara biologi.   ABSTRACT The objectives of this research was to study the biosorption and reduction of chromium bearing tannery wastewater using biomass of Fusarium sp and Aspergillus niger. Fusarium sp was used to investigate bioaccumulation and reduction of chromium in K2 Cr2O7 solution and solution containing sludge of leather tanning waste, and aspergillus niger was used to investigate biosorption of Cr(III and Cr(VI in solution. Fusarium sp was grown on sterilized potato extrose liquid medium, added with K2Cr2O7solution or sludge

Poultry feed based on protein hydrolysate derived from chrome-tanned leather solid waste: creating value from waste.

Science.gov (United States)

Chaudhary, Rubina; Pati, Anupama

2016-04-01

Leather industry generates huge amount of chrome-containing leather solid waste which creates major environment problems to tanners worldwide. Chrome-tanned leather solid waste is primarily chromium complex of collagen protein. The presence of chromium limits its protein application in animal feed industry. The purified protein hydrolysate with zero chromium could be used in poultry feed. In this study, an attempt has been made to assess performance of poultry with purified protein hydrolysate as a feed derived from chrome-tanned leather waste as partial replacement of soyabean meal as a sole source of protein for growing broiler chickens. Growth study was conducted to evaluate the effect of feeding protein hydrolysate on performance and physiochemical characteristics of meat of broiler chickens. Two experimental diets containing various levels of protein hydrolysate (EI-20 % and EII-30 %) were evaluated. The comparative study was performed as control with soyabean meal. Daily feed intake, body weight gain and feed conversion ratio were measured from day 8 to day 35. At the end of the study, birds were randomly selected and slaughtered to evaluate for physiochemical characteristics of meat. Diet had significant effects on feed intake and body weight gain. Birds fed with 20 and 30 % protein hydrolysate consumed 9.5 and 17.5 % higher amount of feed and gained 6.5 and 16.6 % higher than soyabean meal-fed birds. The current study produced evidence that protein hydrolysate can replace up to 75 % of soyabean meal in broiler diets without affecting either growth performance or meat characteristics.

High exhaust chrome complex using chrome tanned tannery, solid wastes and common hydrocarbons as reductants and masking agents to minimize the liquid and solid wastes: tanning and environmental impact studies

International Nuclear Information System (INIS)

Nawaz, H.R.

2005-01-01

Still no alternate of chrome tanning has been found to achieve the best quality and quantity of leather. But the chrome tanning process is associated with the generation of very toxic liquid and solid wastes. Therefore we emphasized to develop an efficient process for the synthesis of high exhaust chrome complex that could minimize the both liquid and solid wastes up to very low limit. In this research, chrome shavings and raw organic compounds have beneficially utilized as a reductant as well as potential masking agents providing a comprehensive close loop. Two chrome tanning materials have been developed using leather shavings with molasses in product A and replacement of molasses by other organic compounds for chrome complex B. These materials have also been employed for the tanning of goatskins parallel to the commercial BCS from the market. The comparative studies revealed that, the quality of leather made from product B is either better or comparable with the conventional tanning material. The chrome contents in leather have been increased with the simultaneous decreased in spent chrome liquor. Hence the exhaustion rate of chrome complex B has been noted up to 95%. While the physical characteristics of resulted leather from product A and B have been found comparable to that of conventional tanned leather. Therefore this methodology would not only reduce liquid and solid wastes but also provide quality leather and economically multi benefits. (author)

"Wash leather scrotum" (scrotal dermatitis): a treatable cause of male infertility.

Science.gov (United States)

Hendry, W F; Munro, D D

1990-02-01

A group of 16 male patients with infertility had dermatitis of the scrotum and groins giving lichenified oedematous skin; the resulting thickening and loss of rugosity produced a characteristic appearance that we have termed wash leather scrotum. Treatment of the dermatosis resulted in an improvement in sperm count and motility in most patients, and 5 couples produced one or more pregnancies.

Improvement in surface hydrophilicity and resistance to deformation of natural leather through O{sub 2}/H{sub 2}O low-temperature plasma treatment

Energy Technology Data Exchange (ETDEWEB)

You, Xuewei; Gou, Li, E-mail: gouli@scu.edu.cn; Tong, Xingye

2016-01-01

Graphical abstract: - Highlights: • O{sub 2}/H{sub 2}O can increase oxygen concentration in the plasma compared to the pure O{sub 2} atmosphere. • Pores at the surface of natural leather became larger and deeper with enhanced permeability of water. • The initial water contact angle was about 21°. • Its preferable surface hydrophilicity kept for 3 days, which gives guidance for next process. • The elongation of the treated sample for 10 min was twice as large as that of the untreated sample. - Abstract: The natural leather was modified through O{sub 2}/H{sub 2}O low-temperature plasma treatment. Surface morphology was characterized by scanning electron microscopy (SEM) and the results showed that the pores on the leather surface became deeper and larger with enhanced permeability of water and vapor. XPS and FTIR-ATR was performed to determine the chemical composition of natural leather surface. Oxygen-containing groups were successfully grafted onto the surface of natural leather and oxygen content increased with longer treatment time. After O{sub 2}/H{sub 2}O plasma treatment, initial water contact angle was about 21° and water contact angles were not beyond 55° after being stored for 3 days. Furthermore, the tensile test indicated that the resistance to deformation had a prominent transform without sacrificing the tensile strength.

Effect of age on leather and skin traits of slaughter ostriches | Cloete ...

African Journals Online (AJOL)

Little is known about the factors affecting leather and skin traits in ostriches. The effect of age on physical skin traits of slaughter ostriches was consequently investigated. Forty skins representing slaughter ages ranging from five to 14 months were selected to represent means of the respective age groups with regard to skin ...

New approach of depollution of solid chromium leather waste by the use of organic chelates: economical and environmental impacts.

Science.gov (United States)

Malek, Ammar; Hachemi, Messaoud; Didier, Villemin

2009-10-15

Herein, we describe an original novel method which allows the decontamination of the chromium-containing leather wastes to simplify the recovery of its considerable protein fractions. Organic salts and acids such as potassium oxalate, potassium tartrate, acetic and citric acids were tested for their efficiency to separate the chromium from the leather waste. Our investigation is based on the research of the total reversibility of the tanning process, in order to decontaminate the waste without its previous degradation or digestion. The effect of several influential parameters on the treatment process was also studied. Therefore, the action of chemical agents used in decontamination process seems very interesting. The optimal yield of chromium extraction about 95% is obtained. The aim of the present study is to define a preliminary processing of solid leather waste with two main impacts: Removing with reusing chromium in the tanning process with simple, ecological and economic treatment process and potential valorization of the organic matrix of waste decontaminated.

A randomized single blind crossover trial comparing leather and commercial wrist splints for treating chronic wrist pain in adults

Science.gov (United States)

Thiele, Jill; Nimmo, Rachel; Rowell, Wendy; Quinn, Stephen; Jones, Graeme

2009-01-01

Background To compare the effectiveness of a custom-made leather wrist splint (LS) with a commercially available fabric splint (FS) in adults with chronic wrist pain. Methods Participants (N = 25, mean age = 54) were randomly assigned to treatment order in a 2-phase crossover trial. Splints were worn for 2 weeks, separated by a one-week washout period. Outcomes were assessed at baseline and after each splint phase using the Australian/Canadian Osteoarthritis Hand Index (AUSCAN), the Canadian Occupational Performance Measure (COPM) and Jamar dynamometer by an observer blinded to treatment allocation. Results Both styles of wrist splint significantly reduced pain (effect size LS 0.79, FS 0.43), improved hand function and increased grip strength compared to baseline (all p leather splint compared to the commercially available splint. Conclusion Leather wrist splints were superior to a commercially available fabric splint for the short-term relief of pain and dysfunction. PMID:19843345

Time-dependent effect of composted tannery sludge on the chemical and microbial properties of soil.

Science.gov (United States)

de Sousa, Ricardo Silva; Santos, Vilma Maria; de Melo, Wanderley Jose; Nunes, Luis Alfredo Pinheiro Leal; van den Brink, Paul J; Araújo, Ademir Sérgio Ferreira

2017-12-01

Composting has been suggested as an efficient method for tannery sludge recycling before its application to the soil. However, the application of composted tannery sludge (CTS) should be monitored to evaluate its effect on the chemical and microbial properties of soil. This study evaluated the time-dependent effect of CTS on the chemical and microbial properties of soil. CTS was applied at 0, 2.5, 5, 10, and 20 Mg ha -1 and the soil chemical and microbial properties were evaluated at 0, 45, 75, 150, and 180 days. Increased CTS rates increased the levels of Ca, Cr, and Mg. While Soil pH, organic C, and P increased with the CTS rates initially, this effect decreased over time. Soil microbial biomass, respiration, metabolic quotient, and dehydrogenase increased with the application of CTS, but decreased over time. Analysis of the Principal Response Curve showed a significant effect of CTS rate on the chemical and microbial properties of the soil over time. The weight of each variable indicated that all soil properties, except β-glucosidase, dehydrogenase and microbial quotient, increased due to the CTS application. However, the highest weights were found for Cr, pH, Ca, P, phosphatase and total organic C. The application of CTS in the soil changed the chemical and microbial properties over time, indicating Cr, pH, Ca, phosphatase, and soil respiration as the more responsive chemical and microbial variables by CTS application.

Effect of different processing stages of commercial fruit leather on patulin reduction

Directory of Open Access Journals (Sweden)

M.H Eskandari

2014-11-01

Full Text Available Fruit leather (Lavashak is a high consumption food product especially among children in Iran. This product is being manufactured by low quality fruits that usually are contaminated with molds and patulin mycotoxin.  The objective of this study was to determine the effect of industrial processing stages of leather production (including pre-heating, filtration, evaporation, formulation and final heat boiling and drying on reduction of patulin level. Samples were taken for analysis prior and following each processing steps and patulin level was determined using HPLC technique. The results indicated that the maximum reduction of patulin level was ooccurred during formulation and evaporation steps which was estimated at 24.60 and 18.20%, respectively. Meanwhilewhile after drying, filtration, and pre-heating processes, the main loss of patulin was 8.58, 3.82 and 2.48%, respectively. It was concluded that the amount of residual patulin in final product was higher than 40% of its primary concentration. Besides, various processing stages were found insufficient to eliminate all of patulin or to reduce its level to lower than the maximum acceptable limit.

Removal of organic pollutants in tannery wastewater from wet-blue fur processing by integrated Anoxic/Oxic (A/O) and Fenton: Process optimization

DEFF Research Database (Denmark)

Wang, Yong; Li, Weiguang; Angelidaki, Irini

2014-01-01

Treatment of tannery wastewater has been a challenge in remediation of aquatic environment in developing countries. Removal of organic pollutants in tannery wastewater from wet-blue fur processing was studied using integrated processes of Anoxic/Oxic and Fenton. Analysis of COD composition based...... 80%. In the subsequent Fenton oxidation, effects of initial pH and H2O2 dose on COD removal were investigated, and response surface methodology was adopted to obtain the optimal conditions as initial pH of 4.0, H2O2 dose of 14.0mM, H2O2:Fe2+ molar ratio of 10.6, and reaction time of 3h to achieve...... the highest COD removal of 55.87%. GC-MS analysis was carried out to observe the change of organic composition during Fenton oxidation, and most of the residual organic pollutants resistant to Fenton treatment belonged to organosilanes and saturated alkanes. This study will provide useful information...

Evaluation of the genetic alterations in direct and indirect exposures of hexavalent chromium [Cr(VI)] in leather tanning industry workers North Arcot District, South India.

Science.gov (United States)

Balachandar, Vellingiri; Arun, Meyyazhagan; Mohana Devi, Subramaniam; Velmurugan, Palanivel; Manikantan, Pappusamy; Karthick Kumar, Alagamuthu; Sasikala, Keshavarao; Venkatesan, Chinnakulandai

2010-10-01

The focal aim of the present study was to identify the genetic alterations occurring in the tannery workers and surrounding inhabitants chronically exposed to hexavalent chromium [Cr(VI)]. A total of 108 samples which includes 72 exposed subjects [36 directly exposed (DE) subjects and 36 indirectly exposed (IE) subjects] and 36 controls were recruited for this study. The exposed subjects and controls were selected based on the Cr level present in air and their urine. Directly exposed subjects were categorized based on their work duration in the tannery industries, whereas the indirectly exposed subjects were categorized based on their year of residence in the place adjacent to tannery industries for more than 3 decades. Controls were normal and healthy. Age was matched for the exposed subjects and controls. The exposed subjects as well as the controls were categorized based on their age (group I, 41 years). Cell cultures were established from blood samples (5 ml from each subject) collected from the subjects (exposed subjects and controls) after obtaining informed consent. G-banding (Giemsa staining) of the cultures, micronucleus (MN) assay and comet assay were used to identify the genetic alterations of individuals exposed to Cr(VI) in comparison with the controls. A higher degree of total CA [12 ± 8.49 (21-25 years)] and MN [18.69 ± 7.39 (11-15 years)] was found in DE subjects compared to other groups. In IE subjects, elevated levels of CA [5.67 ± 1.15 (51-60 years)] and MN [25 ± 9.89 (71-80 years)] were observed. As expected, controls exhibited minimal number of alterations. The overall CA frequency due to Cr exposure was significantly different from that of the controls for both chromatid and chromosome type aberrations (P < 0.05 by ANOVA). The MN/1,000 binucleated cells were significantly increased (P < 0.05) in the peripheral lymphocytes of DE and IE subjects in comparison with controls. The mean tail length of comet assay for DE, IE and controls were

Determination of concentrations of chromium and other elements in soil and plant samples from leather tanning area by Instrumental Neutron Activation Analysis

International Nuclear Information System (INIS)

Rohit Kumar; Rai, A.K.; Alamelu, D.; Acharya, R.

2014-01-01

Chromium, one of the toxic elements, along with other elements has been determined in samples of soil and plant (leaves and seeds) from Jajmau Area, Kanpur district, India, which is irrigated with effluent waste water from leather tanning industries. Soil and plant samples were collected from these areas and analyzed by Instrumental Neutron Activation Analysis (INAA) using high flux reactor neutrons and high resolution gamma-ray spectrometry. Concentrations of fifteen elements in soil and five elements in plant samples were determined by relative method. Chromium concentrations were found to be in range of 45-3,900 mg kg -1 in soil samples and 14-83 mg kg -1 in plant samples. This study showed that Cr is present in significant amounts, in the soil as well as in the plant samples, near to the leather tanning area. As a part of quality control work, IAEA reference material (RM) SL-3 and NIST standard reference material (SRM) 1645 were analyzed and the quality of the results has been evaluated by calculating % deviations from recommended/literature/certified values. (author)

Bloodstains on Leather: Examination of False Negatives in Presumptive Test and Human Hemoglobin Test.

Science.gov (United States)

Castelló, Ana; Francès, Francesc; Verdú, Fernando

2017-09-01

Presumptive tests for blood are very simple and sensitive tests used in the search for evidence. They also provide initial information on the nature of stains. A second test can confirm their nature. However, these tests can present false-negative results for different reasons. Some of those reasons have been studied, while others, those caused by the substrate material that contains the stain, are less well known. This work studies the effect of one component of a leather substrate-quebracho extract-on presumptive and human hemoglobin blood tests. Assays were performed using samples of blood dilutions contaminated with quebracho extract and others formed on a substrate containing the contaminant. Results show an undoubted interference that causes false negatives and even visible to the naked eye stains and also indicate that some tests (phenolphthalein) are more affected than others. Examiners should be taken into account when working on this kind of substrates. © 2017 American Academy of Forensic Sciences.

Bio-mimetic mineralization potential of collagen hydrolysate obtained from chromium tanned leather waste

International Nuclear Information System (INIS)

Banerjee, Pradipta; Madhu, S.; Chandra Babu, N.K.; Shanthi, C.

2015-01-01

Hydroxyapatite (HA) ceramics serve as an alternative to autogenous-free bone grafting by virtue of their excellent biocompatibility. However, chemically synthesized HA lacks the strong load-bearing capacity as required by bone. The bio-mimetic growth of HA crystals on collagen surface provides a feasible solution for synthesizing bone substitutes with the desired properties. This study deals with the utilization of the collagen hydrolysate recovered from leather waste as a substrate for promoting HA crystal growth. Bio-mimetic growth of HA was induced by subjecting the hydrolysate to various mineralization conditions. Parameters that would have a direct effect on crystal growth were varied to determine the optimal conditions necessary. Maximum mineralization was achieved with a combination of 10 mM of CaCl 2 , 5 mM of Na 2 HPO 4 , 100 mM of NaCl and 0.575% glutaraldehyde at a pH of 7.4. The metal–protein interactions leading to formation of HA were identified through Fourier-transform infrared (FTIR) spectroscopy and x-ray diffraction (XRD) studies. The crystal dimensions were determined to be in the nanoscale range by atomic force microscopy (AFM) and scanning electron microscopy (SEM). The size and crystallinity of bio-mimetically grown HA indicate that hydrolysate from leather waste can be used as an ideal alternative substrate for bone growth. - Highlights: • Collagen hydrolysate, extracted from leather industry waste is subjected to biomineralization. • Optimal conditions required for HA growth are identified. • FTIR studies reveal higher Ca−COO − and low C−N stretch with higher HA formation. • AFM and SEM studies reveal nanometer ranged HA crystals

Removal of Cr(VI and Toxic Ions from Aqueous Solutions and Tannery Wastewater Using Polymer-Clay Composites

Directory of Open Access Journals (Sweden)

Abd El-Azeem Sallam

2017-10-01

Full Text Available Polymer-clay composites were prepared by natural zeolite (clinoptilolite or naturally local clay deposits in an N,N-methylene-bis-acrylamide as cross-linked. The resultant composites were used for the removal of Cr(VI from an aqueous solution. Additionally, their effects on soluble ions of tannery wastewater were investigated. The produced composites were characterized using X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FT-IR, and scanning electron microscopy (SEM. The results showed that Cr(VI removal is dependent upon initial concentrations and pH. The adsorption quantity of Cr(VI onto the polymerized clay deposit followed by polymerized zeolite exhibited higher values than their original samples. The polymer-clay composite of clay deposit showed the highest removal of 76.3–100% overall initial concentrations of 10–50 mg L−1 and at initial pH of 2. Kinetics of Cr(VI removal by various sorbents was predicted using a pseudo–second order model. Our findings showed that the levels of salinity and various soluble ions (Cr2+, Na+, Cl− and SO42− in tannery wastewater are very high, and their levels were reduced after treatment, especially by polymerized sorbents. It could be concluded that the polymer-clay composites may be employed as a highly efficient sorbent for the removal of Cr(VI and toxic ions from the wastewater.

Heterocatalytic Fenton oxidation process for the treatment of tannery effluent: kinetic and thermodynamic studies.

Science.gov (United States)

Karthikeyan, S; Ezhil Priya, M; Boopathy, R; Velan, M; Mandal, A B; Sekaran, G

2012-06-01

BACKGROUND, AIM, SCOPE: Treatment of wastewater has become significant with the declining water resources. The presence of recalcitrant organics is the major issue in meeting the pollution control board norms in India. The theme of the present investigation was on partial or complete removal of pollutants or their transformation into less toxic and more biodegradable products by heterogeneous Fenton oxidation process using mesoporous activated carbon (MAC) as the catalyst. Ferrous sulfate (FeSO(4)·7H(2)O), sulfuric acid (36 N, specific gravity 1.81, 98% purity), hydrogen peroxide (50% v/v) and all other chemicals used in this study were of analytical grade (Merck). Two reactors, each of height 50 cm and diameter 6 cm, were fabricated with PVC while one reactor was packed with MAC of mass 150 g and other without MAC served as control. The oxidation process was presented with kinetic and thermodynamic constants for the removal of COD, BOD, and TOC from the wastewater. The activation energy (Ea) for homogeneous and heterogeneous Fenton oxidation processes were 44.79 and 25.89 kJ/mol, respectively. The thermodynamic parameters ΔG, ΔH, and ΔS were calculated for the oxidation processes using Van't Hoff equation. Furthermore, the degradation of organics was confirmed through FTIR and UV-visible spectroscopy, and cyclic voltammetry. The heterocatalytic Fenton oxidation process efficiently increased the biodegradability index (BOD/COD) of the tannery effluent. The optimized conditions for the heterocatalytic Fenton oxidation of organics in tannery effluent were pH 3.5, reaction time-4 h, and H(2)O(2)/FeSO(4)·7H(2)O in the molar ratio of 2:1.

Development of an artisanal tanning method of the acoupa weakfish (Cynoscion acoupa skin and its transfer through a workshop to a community in the city of Bragança, PA, Brazil

Directory of Open Access Journals (Sweden)

Bruno José Corecha Fernandes Eiras

2015-04-01

Full Text Available Bragança is one of the largest fishing centers in the state of Pará, northern Brazil. In the city, there are several environmental and socio-economic problems such as lack of waste management and contamination of water sources that supply to the city and the Caeté river estuary. The social and economic problems are mainly caused by social inequality, which usually occurs in communities where the population depends mainly on fishing. Fish waste forms a part of the waste disposed in the region. Fish skin represents a significant portion of this waste and may be used for manufacturing leather by the tanning process, thereby generating income for the community and reducing environmental impacts. The acoupa weakfish (Cynoscion acoupa has a high potential for tanning because of its large size and high yield of skin. The aim of this study was to develop a methodology for artisanal skin tanning of acoupa weakfish and the subsequent transfer of this methodology to a fishing community through a workshop. The methodology developed in the laboratory is more streamlined than traditional methods and is based on tanning methods cited in the literature and techniques applied in regional tanneries. To assess the quality of acoupa weakfish leather, resistance tests were performed, which proved its potential for manufacturing clothing and footwear. An economic analysis of the hypothetical production of leather based on the tanning methodology developed in this work revealed that the project is feasible and the effluents generated during the process are less harmful to the environment, compared to those generated by traditional tanning methods.

Selection of the Chrome Reduction Bacteria in the Waste of Tanning Leather Industries by Ozonization Method

International Nuclear Information System (INIS)

Yazid, M.; Aris Bastianudin; Widdi Usada

2007-01-01

Selection of the chrome reduction bacteria in the waste of tanning leather industries by ozonization method has been done. The objectives of this research was to obtain isolate bacteria from the waste with chrome contain, so that expected can be used for chrome bioremediation agent for arrange to improved the waste treatment for tanning leather industries. Selection of bacteria in the waste was carried out by ozonization method with time variation 0 to 210 minutes by time interval 15 minutes. Isolation bacteria was carried out was grown on the BHI media for 24 hours at 37°C temperature. So be inoculated by streak plate method on the TBX, MC, EA, CTM and BP media. Characterization of bacteria was done by saw the colonies morphology, sel morphology and biochemical characterization. So, identification of isolate bacteria by matching profile method. The result of this research can be obtained 5 isolate bacteria BCR1, BCR2, BCR3, BCR4 and BCR5 with the different phenotypic character. From the five isolate can be selected resistance ozon isolate until 180 minutes time ozonization were BCR 2, were identified belong to the genus of Bacillus. The examination results showed that the isolate bacteria be able to reduction of the chrome concentration in the waste of tanning leather industries by 71.03 %. Efficiency. (author)

Root proteome response to growth on tannery waste in three different poplar species with various adaptation abilities

Directory of Open Access Journals (Sweden)

Zemleduch-Barylska A.

2013-04-01

Full Text Available In our study we compared growth of three poplar clones (Populus tremula ×alba, P. alba ‘Villafranca” and P. nigra on chromium-containing solid tannery waste. Tolerance index of saplings ranged from only 25% for P. nigra up to 80% for P. tremula x alba. Standard morphological, chemical and biochemical analyses also confirmed significant differences in reaction of all tested clones to such growth conditions. Preliminary proteomic study showed an unequal level of changes in protein profiles from roots in different poplars.

The effect of electron acceptors on biogas production from tannery sludge of a Mexican wastewater plant

Science.gov (United States)

Effluents from the leather processing plants generally are discharged into rivers or are used to irrigate farmland. The biogas production from the digestion of sludge produced could be used as alternative sources for energy and power generation. A study was carried out to examine the effects of vari...

Ultrasound assisted enhancement in natural dye extraction from beetroot for industrial applications and natural dyeing of leather.

Science.gov (United States)

Sivakumar, Venkatasubramanian; Anna, J Lakshmi; Vijayeeswarri, J; Swaminathan, G

2009-08-01

There is a growing demand for eco-friendly/non-toxic colorants, specifically for health sensitive applications such as coloration of food and dyeing of child textile/leather garments. Recently, dyes derived from natural sources for these applications have emerged as an important alternative to potentially harmful synthetic dyes and pose need for suitable effective extraction methodologies. The present paper focus on the influence of process parameters for ultrasound assisted leaching of coloring matter from plant materials. In the present work, extraction of natural dye from beetroot using ultrasound has been studied and compared with static/magnetic stirring as a control process at 45 degrees C. The influence of process parameters on the extraction efficiency such as ultrasonic output power, time, pulse mode, effect of solvent system and amount of beetroot has been studied. The use of ultrasound is found to have significant improvement in the extraction efficiency of colorant obtained from beetroot. Based on the experiments it has been found that a mixture of 1:1 ethanol-water with 80W ultrasonic power for 3h contact time provided better yield and extraction efficiency. Pulse mode operation may be useful in reducing electrical energy consumption in the extraction process. The effect of the amount of beetroot used in relation to extraction efficiency has also been studied. Two-stage extraction has been studied and found to be beneficial for improving the yield for higher amounts of beetroot. Significant 8% enhancement in % yield of colorant has been achieved with ultrasound, 80W as compared to MS process both using 1:1 ethanol-water. The coloring ability of extracted beet dye has been tested on substrates such as leather and paper and found to be suitable for dyeing. Ultrasound is also found to be beneficial in natural dyeing of leather with improved rate of exhaustion. Both the dyed substrates have better color values for ultrasonic beet extract as inferred from

A Teoria das Restrições: estudo de caso em uma indústria de couros do Estado de Santa Catarina

Directory of Open Access Journals (Sweden)

Fernanda da Silva Fernandes

2009-01-01

Full Text Available This study investigates the application of the tenets of the Theory of Constraints (TOC in a leather factory with an integrated tannery. The purpose was to empirically demonstrate the application of this theory to decision-making related to constraint management and productivity improvement. This study analyzes the main constraints in the productive process of the company being investigated, as well as the implementation of TOC, relying on information gathered through interviews and accounting statements. The results show that by applying the TOC principles, it is possible to improve and expedite the decision-making process, focusing on specifi c goals: profi t and growth.

Gold nanoparticles mediated coloring of fabrics and leather for antibacterial activity.

Science.gov (United States)

Velmurugan, Palanivel; Shim, Jaehong; Bang, Keuk-Soo; Oh, Byung-Taek

2016-07-01

Metal gold nanoparticles (AuNPs) were synthesized in situ onto leather, silk and cotton fabrics by three different modules, including green, chemical, and a composite of green and chemical synthesis. Green synthesis was employed using Ginkgo biloba Linn leaf powder extract and HAuCl4 with the fabrics, and chemical synthesis was done with KBH4 and HAuCl4. For composite synthesis, G. biloba extract and KBH4 were used to color and embed AuNPs in the fabrics. The colored fabrics were tested for color coordination and fastness properties. To validate the green synthesis of AuNPs, various instrumental techniques were used including UV-Vis spectrophotometry, HR-TEM, FTIR, and XRD. The chemical and composite methods reduce Au(+) onto leather, silk and cotton fabrics upon heating, and alkaline conditions are required for bonding to fibers; these conditions are not used in the green synthesis protocol. FE-SEM image revealed the binding nature of the AuNPs to the fabrics. The AuNPs that were synthesized in situ on the fabrics were tested against a skin pathogen, Brevibacterium linens using LIVE/DEAD BacLight Bacterial Viability testing. This study represents an initial route for coloring and bio-functionalization of various fabrics with green technologies, and, accordingly, should open new avenues for innovation in the textile and garment sectors. Copyright © 2016 Elsevier B.V. All rights reserved.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil

International Nuclear Information System (INIS)

Tariq, Saadia R.; Shah, Munir H.; Shaheen, Nazia

2009-01-01

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil.

Science.gov (United States)

Tariq, Saadia R; Shah, Munir H; Shaheen, Nazia

2009-09-30

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Comparative statistical analysis of chrome and vegetable tanning effluents and their effects on related soil

Energy Technology Data Exchange (ETDEWEB)

Tariq, Saadia R. [Department of Chemistry, Lahore College for Women University, Lahore (Pakistan); Shah, Munir H., E-mail: munir_qau@yahoo.com [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Shaheen, Nazia [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan)

2009-09-30

Two tanning units of Pakistan, namely, Kasur and Mian Channun were investigated with respect to the tanning processes (chrome and vegetable, respectively) and the effects of the tanning agents on the quality of soil in vicinity of tanneries were evaluated. The effluent and soil samples from 16 tanneries each of Kasur and Mian Channun were collected. The levels of selected metals (Na, K, Ca, Mg, Fe, Cr, Mn, Co, Cd, Ni, Pb and Zn) were determined by using flame atomic absorption spectrophotometer under optimum analytical conditions. The data thus obtained were subjected to univariate and multivariate statistical analyses. Most of the metals exhibited considerably higher concentrations in the effluents and soils of Kasur compared with those of Mian Channun. It was observed that the soil of Kasur was highly contaminated by Na, K, Ca and Mg emanating from various processes of leather manufacture. Furthermore, the levels of Cr were also present at much enhanced levels than its background concentration due to the adoption of chrome tanning. The levels of Cr determined in soil samples collected from the vicinity of Mian Channun tanneries were almost comparable to the background levels. The soil of this city was found to have contaminated only by the metals originating from pre-tanning processes. The apportionment of selected metals in the effluent and soil samples was determined by a multivariate cluster analysis, which revealed significant differences in chrome and vegetable tanning processes.

Preparation of highly-oxidized starch using hydrogen peroxide and its application as a novel ligand for zirconium tanning of leather.

Science.gov (United States)

Yu, Yue; Wang, Ya-Nan; Ding, Wei; Zhou, Jianfei; Shi, Bi

2017-10-15

A series of highly-oxidized starch (HOS) were prepared using H 2 O 2 and a copper-iron catalyst as a desired ligand for zirconium tanning of leather. The effects of catalyst and H 2 O 2 dosages, and reaction temperature on the oxidation degree (OD, represented as the amount of carbonyl and carboxyl groups derived) of starch were investigated. The OD reached 76.2% when oxidation was conducted using 60% H 2 O 2 and 0.015% catalyst at 98°C for 2h. 13 C NMR and FT-IR illustrated carbonyl and carboxyl groups were formed in HOS after oxidation. GPC and laser particle size analyses indicated the decrease of HOS molecular size with increasing H 2 O 2 dosage and OD. HOS with moderate OD and molecular weight was able to coordinate with zirconium and remarkably improve tanning process. Leather tanned by Zr complexes using HOS-60 (60% H 2 O 2 , Mn 3516g/mol) as ligand presented considerably better physical and organoleptic properties than those of traditional Zr-tanned leather. Copyright © 2017 Elsevier Ltd. All rights reserved.

Screening of tannin acyl hydrolase (E.C.3.1.1.20) producing tannery effluent fungal isolates using simple agar plate and SmF process.

Science.gov (United States)

Murugan, K; Saravanababu, S; Arunachalam, M

2007-03-01

Industrially important tannase producing fungi were isolated from tannery effluent using simple agar plate method. The isolates were screened by submerged fermentation using auto-controlled bioreactor. The colony diameter on the solid surface media shows high correlation with quantitative production of tannase. The isolate Aspergillus niger shows maximum production of both extracellular and intracellular enzyme.

Vitrification: An alternative to minimize environmental impact caused by leather industry wastes

International Nuclear Information System (INIS)

Basegio, T.; Beck Leao, A.P.; Bernardes, A.M.; Bergmann, C.P.

2009-01-01

The main purpose of this work was the investigation of the immobilization of chromium ion present in the ash from the incineration of chromium-tanned leather shavings (ACS) by means of vitrified ceramic bodies. To achieve the immobilization samples were initially produced adding soda-lime glass to ACS. After that, new formulations were produced with the addition of pure oxides, TiO 2 and MgO, to the soda-lime glass and ACS sample. These samples were conformed by pressing and fired in an eletrical furnace, at temperatures of 750, 800, 950 and 1000 o C. The ceramic bodies were evaluated with respect to their physical properties and mineralogical composition by X-ray diffraction and energy dispersive spectroscopy (EDS) mapping. The chromium immobilization was characterized by leaching tests according to Brazilian Regulations (NBR 10005). The results confirmed the immobilization of the chromium ion within the allowed limits of Brazilian Regulations, NBR 10004 (5 mg/L), with the use of glass and vitrification/densification agents such as titanium and magnesium oxides.

Total control of chromium in tanneries - thermal decomposition of filtration cake from enzymatic hydrolysis of chrome shavings.

Science.gov (United States)

Kocurek, P; Kolomazník, K; Bařinová, M; Hendrych, J

2017-04-01

This paper deals with the problem of chromium recovery from chrome-tanned waste and thus with reducing the environmental impact of the leather industry. Chrome-tanned waste was transformed by alkaline enzymatic hydrolysis promoted by magnesium oxide into practically chromium-free, commercially applicable collagen hydrolysate and filtration cake containing a high portion of chromium. The crude and magnesium-deprived chromium cakes were subjected to a process of thermal decomposition at 650°C under oxygen-free conditions to reduce the amount of this waste and to study the effect of magnesium removal on the resulting products. Oxygen-free conditions were applied in order to prevent the oxidation of trivalent chromium into the hazardous hexavalent form. Thermal decomposition products from both crude and magnesium-deprived chrome cakes were characterized by high chromium content over 50%, which occurred as eskolaite (Cr 2 O 3 ) and magnesiochromite (MgCr 2 O 4 ) crystal phases, respectively. Thermal decomposition decreased the amount of chrome cake dry feed by 90%. Based on the performed experiments, a scheme for the total control of chromium in the leather industry was designed.

N-nitroso compounds in the air environment

International Nuclear Information System (INIS)

Fine, D.H.; Edwards, G.S.; Krull, I.S.; Wolf, M.H.

1979-01-01

The measurement and chemistry of N-nitroso compounds, most of which are known carcinogens, in the air are discussed. Methods for the analysis of N-nitroso compounds in the ambient air usually employ a nitrosamine-specific detector, coupled to a gas chromatograph or a high-pressure liquid chromatograph, with structural confirmation by high-resolution mass spectroscopy and extensive artifact experiments required. Airborne N-nitrosamines have been detected at significant trace levels near leather tanneries, rocket fuel plants, tire factories, tobacco smoke, amine factories, cooking vapors and in the ambient air. Nitrosation of amines has been demonstrated with nitrogen oxides, certain C-nitro compounds and nitrous acid, and tertiary amines, tertiary amine oxides and primary amines have been nitrosated

A contribution to the industrial valorization of tannery waste: the case of cement industry; Contribution a la valorisation industrielle des dechets de tanneries: cas de la cimenterie

Energy Technology Data Exchange (ETDEWEB)

Yatribi, A.; Boukhars, L. [Service de l' Environnement, Div. de l' Urbanisme, Province de Kenitra (Morocco); Nejmeddine, A. [Laboratoire d' Ecotoxicologi, Faculte des Sciences Semlalia, Marrakech (Morocco)

2001-04-01

The present work addresses the possibility of valorization of tannery waste incineration ashes in the cement industry. To this end, the impact of the addition of ashes at various percentages (0, 5, 10, 15, 20, 25, 30, 35, 40 and 45 % in mass) on some mechanical and physical parameters of cement was examined: normal consistency (%), the beginning of setting (hr), the end of setting (hr), the hot expansion (mm), the resistances to compression and to bending (N/mm{sup 2}) determined on normalized 4 x 4 x 16 cm samples. The impact of the treatment environment (20 deg C and 100 % of relative humidity RH, 30 deg C and 70 % RH, 45 deg C and 45 % RH) was also taken into consideration. The obtained results reveal that the normal consistency, the beginning and the end of setting vary linearly with the quantity of added ashes. Above an addition of ashes of 30 %, the end of setting exceeds the standards demanding a maximum of 10 hours. Additionally, the results indicate that whatever the environment treatment may be, the resistances to compression and to bending increase with the increase of the sample age; they vary inversely to the amount of ash addition. The results allow to conclude that for an ash addition of 15 % and after an ageing of 30 days, the resistance to compression is higher than 40 N/mm{sup 2}, thus allowing the production of CPA 400 cement. These results also allow to conclude that samples kept in a humid environment give the best resistances to compression and to bending, by comparison with those kept in a dry environment. (authors)

Preparation, characterization and application of dispersible and spherical Nano-SiO2@Copolymer nanocomposite in leather tanning

Science.gov (United States)

Pan, Hui; Li, Guang-Long; Liu, Rui-Qi; Wang, Su-Xia; Wang, Xiao-Dong

2017-12-01

Dispersible and spherical silica nanoparticles (nano-SiO2) were prepared with tetraethyl silicate and different surface-modifiers via a simple method. The silica nanoparticles surface-modified with methacryloxy (propyl) trimethoxysilane (denoted as MPS-SiO2), dimethyl diallyl ammoniumchloride (denoted as DMDAAC-SiO2) and poly (methacrylic acid) (denoted as PMAA-SiO2) which are known as hydrophobic, amphiphilic and hydrophilic modifiers, respectively, exhibited excellent dispersibility in various solvents or polymer matrix. The obtained bare silica nanoparticles, MPS-SiO2, DMDAAC-SiO2 and PMAA-SiO2 were characterized by Fourier transform infrared spectra (FTIR), thermogravimetric analysis (TGA), transmission electron microscope (TEM) and scanning electron microscope (SEM). A series of nanocomposites (denoted as SiO2/P, MPS-SiO2/P, DMDAAC-SiO2/P and PMAA-SiO2/P, respectively) were also prepared with the bare or surface-modified silica nanoparticles and methacrylic acid-co-acrylamide-co-acrylonitrile-co-salicylic acid tetrabasic copolymer (denoted as PMAAS) and applied in leather tanning. Compared with those of the leather tanned with the commercial acrylic resin (CHINATAN OM) and pure tetrabasic copolymer tanning agents, the physical and mechanical properties, rheological properties and thermal stabilities of the leather treated with SiO2/P, MPS-SiO2/P, DMDAAC-SiO2/P or PMAA-SiO2/P founded to be improved in a significant way. Moreover, the highest shrinkage temperature of the wet-white sheepskin tanned with PMAA-SiO2/P reached to 76 °C and the thickness increase reached to 105%.

Studying the causes of high chromium concentration in the leather production process at Tehran Charmshahr industrial complex

Directory of Open Access Journals (Sweden)

M. Mahdiabadi

2016-04-01

  Results: The results indicated the existence of toxic pollutants such as Cr+3 and Cr+6 in leather wastewater, the relatively high level of organic loads with low biodegradability, high levels of COD, BOD, TDS and finally the complexity of the treatment of wastewater.

Analyzing the environmental impact of transportation in reengineered supply chains: a case study from a leather upholstery company

NARCIS (Netherlands)

Yazan, Devrim Murat; Yazan, Devrim; Petruzzelli, Antonio Messeni; Albino, Vito

2011-01-01

This paper examines the impact of process disaggregation and specialization on the environmental performance of the supply chain of a leather upholstery company. An enterprise input–output model that relates geographical information with production processes and transportation routes is developed.

Transformation of Collagen into Gelatine in Historical Leather and Parchment Caused by Natural Deterioration and Moist Treatment

DEFF Research Database (Denmark)

2013-01-01

It is known that, for parchment and leather tanned with condensed types of vegetable tannins stored under acid conditions, chemical deterioration may lead to a transformation of the collagen into a gelatine-like substance that may dissolve in water even at ambient temperature. In a previous study...

Production and stochastic efficiency: An application to the Colombian footwear and leather industry

OpenAIRE

Jorge Barrientos Marín; David Tobón; Alderid Gutiérrez

2009-01-01

In this paper, we characterize and study the efficiency of a representative set of firms in the leather and footwear sector in Bogotá, Bucaramanga, Cúcuta and the Metropolitan Area of Medellin. This study is based on a survey addressing multiple aspects of production in this industry (inputs, integration of activities, administrative management, innovation, exports, etc). Our results suggest that a reasonable percentage of total variance is accounted for by the variance of the inefficiency te...

Optimization of inoculum to substrate ratio for bio-energy generation in co-digestion of tannery solid wastes

Energy Technology Data Exchange (ETDEWEB)

Sri Bala Kameswari, K.; Chitra Kalyanaraman,; Porselvam, S. [Central Leather Research Institute (CLRI), Environmental Technology Division, Chennai (India); Thanasekaran, K. [Anna University, Centre for Environmental Studies, Chennai (India)

2012-04-15

The inoculum to substrate (I/S) ratio is an important factor which influences the anaerobic digestion process. In this study, the effect of different I/S ratios on the performance of co-digestion of fleshings along with mixture of sludge generated during treatment of tannery wastewater was investigated. The parameters studied were biogas generation, volatile solids reduction, volatile fatty acid (VFA) production, and the stability of the digestion process based on VFA to alkalinity ratio was evaluated for various I/S ratios. Economical significance of I/S ratio as related to the volume of the anaerobic digester and the potential benefit of bio-energy generated are discussed in detail. (orig.)

The problems of professional training of practice-oriented specialists for small enterprises of footwear and leather production industries in Uzbekistan

Science.gov (United States)

Ilkhamova, M. U.; Gafurov, J. K.; Maksudova, U. M.; Vassiliadis, S.

2017-10-01

At the present, the State authorities of the Republic of Uzbekistan pay special attention to the development of small and medium businesses and, in particular, to the enterprises oriented on manufacturing products with high added value. The leather and footwear industry of Uzbekistan is one of the dynamically developing sectors of economy. However, the study of the situation demonstrates that the increase in number of small and medium footwear and leather enterprises that have taken place in recent years, is not accompanied by a formation of corresponding professional training system for the enterprises, especially for associate specialists. The analysis of the legal base disclosed that the professional training level in footwear industry enterprises does not meet the up-to-date manufacturing requirements. The study is devoted to the issues of professional training of practice-oriented staff - the specialists for small enterprises of footwear and leather industry. The main task is the development of new vocational courses and programs for the training and professional development of personnel at all levels. The basic stages of complete staff training cycle for footwear sector have been determined based on the practical experience of staff training for small footwear enterprises in Greece. The 3-6 months duration short-term courses recommended for associate and medium level specialists have been developed and evaluated.

Models of verbal working memory capacity: what does it take to make them work?

Science.gov (United States)

Cowan, Nelson; Rouder, Jeffrey N; Blume, Christopher L; Saults, J Scott

2012-07-01

Theories of working memory (WM) capacity limits will be more useful when we know what aspects of performance are governed by the limits and what aspects are governed by other memory mechanisms. Whereas considerable progress has been made on models of WM capacity limits for visual arrays of separate objects, less progress has been made in understanding verbal materials, especially when words are mentally combined to form multiword units or chunks. Toward a more comprehensive theory of capacity limits, we examined models of forced-choice recognition of words within printed lists, using materials designed to produce multiword chunks in memory (e.g., leather brief case). Several simple models were tested against data from a variety of list lengths and potential chunk sizes, with test conditions that only imperfectly elicited the interword associations. According to the most successful model, participants retained about 3 chunks on average in a capacity-limited region of WM, with some chunks being only subsets of the presented associative information (e.g., leather brief case retained with leather as one chunk and brief case as another). The addition to the model of an activated long-term memory component unlimited in capacity was needed. A fixed-capacity limit appears critical to account for immediate verbal recognition and other forms of WM. We advance a model-based approach that allows capacity to be assessed despite other important processing contributions. Starting with a psychological-process model of WM capacity developed to understand visual arrays, we arrive at a more unified and complete model. Copyright 2012 APA, all rights reserved.

EFFECTS OF FATLIQURING PROCESS ON LEATHERS COLOURED WITH IR REFLECTIVE DYES AND PIGMENTS

OpenAIRE

MUTLU Mehmet Mete; ORK Nilay; YAKUT Fatih

2017-01-01

Black coloured materials and consumer goods are known to be heating up more, because they absorb sun radiation more than light colours. This heating is a problem for the users for black automotive or motorcycle leathers and also for dark shoes and boots which are exposed to sun heat. Human vision system can distinguish visible colours between the wavelengths of 390-700 nm. So reflecting the sun radiation in the infrared area of radiation spectrum higher than 700nm, is a solution for heating p...

The sixteenth-century altar painting of the Cattaran (Kotor fraternity of leather-makers

Directory of Open Access Journals (Sweden)

Živković Valentina

2009-01-01

Full Text Available The altar painting that the Cattaran Fraternity of Leather-makers commissioned from the Venetian painter Girolamo da Santa Croce in the first half of the sixteenth century contains the images of Sts Bartholomew, George and Antoninus. The presence of the first two saints is looked at from the perspective of a long-established religious tradition, while the reasons for depicting the archbishop Antoninus giving alms to the poor appear to reside in the then prevailing religious policy and the local social situation.

Studies On Optimization Of Protease Production Using Bacterial Isolate Clri Strain 5468 And Its Application In Dehairing And Hydrolysis Of Tannery Fleshings Solid Waste Management

Directory of Open Access Journals (Sweden)

Vimala Devi Seenivasagham

2015-08-01

Full Text Available The strain which produces protease was originally isolated characterized in Biotechnology laboratory at CLRI and was maintained. The microorganism was growned on several proteolytic media and the maximum activity was observed. The characterization of enzyme was analysed for different pH temperature size of inoculum inhibitors age of the culture. Then the enzyme was observed for the unhairing of skin and the disadvantage in chemical treatment was studied. The conformation of unhairing was studied using histology studies. The tannery waste solid fleshings as it is cannot be directly disposed off to the environment. It was treated with the microbial proteases. The hydrolysis of waste was done using proteases. The solid waste was converted to protien fat and the salt matter. Future work is to optimize the cheap media for the production of the enzyme for large scale applications in various industries.

Ion exchange removal of chromium (iii) from tannery wastes by using a strong acid cation exchange resin amberlite ir-120 h+ and its hybrids

International Nuclear Information System (INIS)

Ahmad, T.

2014-01-01

A strong acid cation exchange resin Amberlite IR-120 H+ and its hybrids with Mn(OH)/sub 2/, Cu(OH)/sub 2/ and Fe(OH)/sub 3/ are used for the removal of chromium (III) from spent tannery bath. The experimental data give good fits with the Langmuir sorption model. The thermodynamic parameters entropy (delta S), enthalpy (delta H) and free energy (delta G) changes are computed, which reveal that the chromium removal from tannery wastes by ion exchangers is an endothermic, physical sorption and entropically driven process. The rate of sorption is found to increase with the increase of resin dosage, stirring speed and temperature. Different kinetic models such as film diffusion, particle diffusion and Lagergren pseudo first order are used to evaluate the mechanism of the process. It is found that the hybrid ion exchange resins have better removal capacity as compared to the parent ion exchanger. The increase in the removal capacity is found to be in the order of the corresponding PZC values of the hybrid ion exchangers. Further, it is suggested that the higher exchange capacity is the result of Donnan effect and specific adsorption of chromium by the oxides / hydroxides present inside the matrix of the organic cation exchanger. (author)

Diffusion and Binding of Laponite Clay Nanoparticles into Collagen Fibers for the Formation of Leather Matrix.

Science.gov (United States)

Shi, Jiabo; Wang, Chunhua; Ngai, To; Lin, Wei

2018-06-13

Understanding accessibility and interactions of clay nanoparticles with collagen fibers is an important fundamental issue for the conversion of collagen to leather matrix. In this study, we have investigated the diffusion and binding of Laponite into the collagen fiber network. Our results indicate that the diffusion behaviors of Laponite into the collagen exhibit the Langmuir adsorption, verifying its affinity for collagen. The introduction of Laponite leads to a shift in the isoelectric point of collagen from ∼6.8 to ∼4.5, indicating the ionic bonding between the positively charged amino groups of the collagen and negatively charged Laponite under the tanning conditions. Fluorescence microscopy, atomic force microscopy, field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, and wide-angle X-ray diffraction analyses reveal that Laponite nanoparticles can penetrate into collagen microstructure and evenly distributed onto collagen fibrils, not altering native D-periodic banding patterns of collagen fibrils. Attenuated total reflectance-Fourier transform infrared and Raman spectroscopy detections further demonstrate the presence of noncovalent interactions, namely, ionic and hydrogen bonding, between Laponite and collagen. These findings provide a theoretical basis for the use of Laponite as an emerging tanning agent in leather manufacture.

Enhancing the economic value and consumer preferences of commercial mondol stingray (Himantura gerardi) leather creative products

Science.gov (United States)

Sahubawa, L.; Pertiwiningrum, A.; Rahmadian, Y.

2018-03-01

The research objectives were to design, assess the economic value and consumer preference level of stingray leather products. The research method included a product design, analysis of economic value and consumer preferences. Mondol stingray (Himantura gerardi) leather, with a length of 50 cm and width of 30 cm, were processed into ID card wallet, man and women’s wallet and key holder. The number of respondents involved to analyze the preference level is 75 respondents (students, lecturers and employees of Universitas Gadjah Mada). Indicators of consumer preferences were model, color, price and purchasing power. The price of ID card wallet is Rp. 450,000; women wallet is Rp. 650,000 and a key holder is Rp. 300,000. Consumer preferences on ID card wallet were as follow: 84 % stated very interesting model; 83 % stated very interesting color; 61 % stated cheap and 53 % had enough. Consumer preferences of women’s wallet were as follow: 81 % stated very interesting model; 84 % stated very interesting color; 56 % stated cheap and 57 % had enough. Consumer preferences on key holder were as follow: 49 % stated interesting model; 72 % stated very interesting color; 61 % stated cheap and 57 % had enough.

Production of Thermoalkaliphilic Lipase from Geobacillus thermoleovorans DA2 and Application in Leather Industry.

Science.gov (United States)

Abol Fotouh, Deyaa M; Bayoumi, Reda A; Hassan, Mohamed A

2016-01-01

Thermophilic and alkaliphilic lipases are meeting a growing global attention as their increased importance in several industrial fields. Over 23 bacterial strains, novel strain with high lipolytic activity was isolated from Southern Sinai, Egypt, and it was identified as Geobacillus thermoleovorans DA2 using 16S rRNA as well as morphological and biochemical features. The lipase was produced in presence of fatty restaurant wastes as an inducing substrate. The optimized conditions for lipase production were recorded to be temperature 60°C, pH 10, and incubation time for 48 hrs. Enzymatic production increased when the organism was grown in a medium containing galactose as carbon source and ammonium phosphate as nitrogen source at concentrations of 1 and 0.5% (w/v), respectively. Moreover, the optimum conditions for lipase production such as substrate concentration, inoculum size, and agitation rate were found to be 10% (w/v), 4% (v/v), and 120 rpm, respectively. The TA lipase with Triton X-100 had the best degreasing agent by lowering the total lipid content to 2.6% as compared to kerosene (7.5%) or the sole crude enzyme (8.9%). It can be concluded that the chemical leather process can be substituted with TA lipase for boosting the quality of leather and reducing the environmental hazards.

Production of Thermoalkaliphilic Lipase from Geobacillus thermoleovorans DA2 and Application in Leather Industry

Directory of Open Access Journals (Sweden)

Deyaa M. Abol Fotouh

2016-01-01

Full Text Available Thermophilic and alkaliphilic lipases are meeting a growing global attention as their increased importance in several industrial fields. Over 23 bacterial strains, novel strain with high lipolytic activity was isolated from Southern Sinai, Egypt, and it was identified as Geobacillus thermoleovorans DA2 using 16S rRNA as well as morphological and biochemical features. The lipase was produced in presence of fatty restaurant wastes as an inducing substrate. The optimized conditions for lipase production were recorded to be temperature 60°C, pH 10, and incubation time for 48 hrs. Enzymatic production increased when the organism was grown in a medium containing galactose as carbon source and ammonium phosphate as nitrogen source at concentrations of 1 and 0.5% (w/v, respectively. Moreover, the optimum conditions for lipase production such as substrate concentration, inoculum size, and agitation rate were found to be 10% (w/v, 4% (v/v, and 120 rpm, respectively. The TA lipase with Triton X-100 had the best degreasing agent by lowering the total lipid content to 2.6% as compared to kerosene (7.5% or the sole crude enzyme (8.9%. It can be concluded that the chemical leather process can be substituted with TA lipase for boosting the quality of leather and reducing the environmental hazards.

Preparation and Surface Sizing Application of Sizing Agent Based on Collagen from Leather Waste

Directory of Open Access Journals (Sweden)

Xuechuan Wang

2015-09-01

Full Text Available Collagen extracted from leather waste was modified with maleic anhydride. Then, using ammonium persulfate as an initiator, by pre-modifying collagen reacted with styrene and ethyl acrylate monomers, a vinyl-grafted collagen sizing agent (VGCSA for paper was prepared. Before the experiment, the performance of VGCSA was tested and VGCSA emulsion was applied to the surface sizing of the corrugated paper. Effects of the amount of VGCSA, the compound proportion of VGCSA, and starch and styrene-acrylic emulsion were studied relative to paper properties. The morphological changes of the paper before and after sizing were characterized by SEM. It was found that the collagen reacted with styrene and ethyl acrylate monomers. Through the grafting of vinyl and collagen, the crystallinity and thermal stability of VGCSA increased. The structure of VGCSA was spherical with a uniform size, and the average particle size was approximately 350 to 400 nm. After being sized, the surface fibers of paper became smooth and orderly. The optimal sizing of VGCSA was 8 g/m2. The optimal proportion of VGCSA with starch was 4:6, and the optimal proportion of VGCSA with SAE was 2:8. The research indicates that collagen extracted from leather waste could be used as a biomaterial, and environmental and economic benefits could be created as well.

Hukum Lingkungan dan Pertanggungjawaban Strict Liability dalam Sistem Hukum Common Law (Studi Kasus Cambridge Water Co. Ltd v. Eastern Countries Leather Plc

Directory of Open Access Journals (Sweden)

Mahfud Mahfud

2010-12-01

Full Text Available ABSTRACT: The possibilities for pollution control still offered today Blackburn J.’s celebrated rule of strict liability, now almost 130 years old, has ensured its continuing popularity. There can be few tort lawyers, however, who have not increasingly wondered how much time should be devoted to a case which has received little judicial attention in recent years, and which was last subjected to detailed consideration by the House of Lords nearly 50 years ago, until, that is, the much-published decision of the House of Lords in Cambridge Water Co. Ltd v. Eastern Countries Leather Plc.   (Environmental Law and The Strict Liability Application In the Common Law System (The Case Study of Cambridge Water Co. Ltd V. Eastern Countries Leather Plc

Studies of obtaining and stability in aqueous medium of new complex compounds of Ti(IV) and Zr(IV) used in ecological leather tanning

Science.gov (United States)

Crudu, Marian; Sibiescu, Doina; Rosca, Ioan; Sutiman, Daniel; Vizitiu, Mihaela

2009-01-01

In this paper, the study of obtaining new coordination compounds of Ti(IV) and Zr(IV) using as ligand: D,L-β-iso-butyric acid, is presented. Also, the stability of these compounds in aqueous medium is studied. The studies of obtaining and of stability of the new compounds were accomplished in aqueous solutions using methods characteristic for coordination compounds: conductance and pH measurements. The combination ratios and the stability were determined with methods characteristic for studies in solutions. From experimental data resulted that the combination ratio of central metallic atoms with the ligand derived from D,L-β-iso-butyric acid was 1:2. From experimental data resulted that in strong acid and strong basic mediums, the coordination compounds could not be obtained. The optimal stability of the studied compounds is limited between 3-6, pH - values. This fact is in accordance with the conditions of using these compounds in ecological leather tanning. Of great importance is that these compounds were used with very good results in tanning processes of different types of leather. This fact evidenced that the ecological alternative of tanning is better than non-ecological tanning using chrome compounds. The importance of this paper consists in obtaining new coordination compounds that can be used in ecological leather tanning.

Isolation and Identification of Bacteria That Has Potential as Producer of Protease Enzyme in the Tannery Industry, PT. Adi Satria Abadi (ASA), YOGYAKARTA

OpenAIRE

Said, M. I; Likadja, J. C

2012-01-01

Bacteria are one of the microorganisms that have the potential as a producer of protease enzyme. Tannery industrial waste is one of the media predicted to contain a number of proteolytic bacteria because of the waste generated is composed largely of protein and fat which are good as growing medium for bacteria. This study aimed to isolate and identify bacteria that have the potential as a producer of protease enzyme. Research conducted at the waste water processing installation (WWPI), tanner...

40 CFR Figure 1 to Subpart Tttt of... - Example Logs for Recording Leather Finish Use and HAP Content

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Example Logs for Recording Leather Finish Use and HAP Content 1 Figure 1 to Subpart TTTT of Part 63 Protection of Environment ENVIRONMENTAL... Finishing Operations Part 63, Subpt. TTTT, Fig. 1 Figure 1 to Subpart TTTT of Part 63—Example Logs for...

Effects of Apple Juice Concentrate, Blackcurrant Concentrate and Pectin Levels on Selected Qualities of Apple-Blackcurrant Fruit Leather

Directory of Open Access Journals (Sweden)

Lemuel M. Diamante

2013-09-01

Full Text Available A study was conducted to determine the effects of different levels of apple juice concentrate (AJC, blackcurrant concentrate (BCC and pectin on the moisture content, water activity, color, texture and ascorbic acid content of apple-blackcurrant fruit leather using the response surface methodology. The results showed the moisture content increased with increasing pectin level and with greater increases at higher AJC and BCC levels while the water activity increased with increasing pectin level and with increasing AJC level, at low pectin levels, but with decreasing AJC, at high pectin levels. The chroma decreased with increasing pectin level and with lower values at the middle AJC level. The puncturing force decreased with increasing AJC level but with a lower value at the middle pectin level. Lastly, the ascorbic acid content increased with increasing BCC level regardless of AJC and pectin levels. There is a need to reduce the drying temperature or time of apple-blackcurrant fruit leather just enough to bring the water activity closer to 0.60, thereby increasing the moisture content resulting in higher product yield.

Effects of Apple Juice Concentrate, Blackcurrant Concentrate and Pectin Levels on Selected Qualities of Apple-Blackcurrant Fruit Leather.

Science.gov (United States)

Diamante, Lemuel M; Li, Siwei; Xu, Qianqian; Busch, Janette

2013-09-12

A study was conducted to determine the effects of different levels of apple juice concentrate (AJC), blackcurrant concentrate (BCC) and pectin on the moisture content, water activity, color, texture and ascorbic acid content of apple-blackcurrant fruit leather using the response surface methodology. The results showed the moisture content increased with increasing pectin level and with greater increases at higher AJC and BCC levels while the water activity increased with increasing pectin level and with increasing AJC level, at low pectin levels, but with decreasing AJC, at high pectin levels. The chroma decreased with increasing pectin level and with lower values at the middle AJC level. The puncturing force decreased with increasing AJC level but with a lower value at the middle pectin level. Lastly, the ascorbic acid content increased with increasing BCC level regardless of AJC and pectin levels. There is a need to reduce the drying temperature or time of apple-blackcurrant fruit leather just enough to bring the water activity closer to 0.60, thereby increasing the moisture content resulting in higher product yield.

Use of ionizing radiation for color removal and increased biodegradability in tannery wastes

International Nuclear Information System (INIS)

Hyfantis, G.J. Jr.

1977-01-01

The special problems associated with the treatment of waste-waters generated by the vegetable leather tanning process have been studied to determine their treatability utilizing ionizing radiation. Conventional treatment schemes do not provide an effective means for the removal of color from vegetable tanning wastes. Radiation treatment is an advanced treatment method that does effectively remove the color. In addition to color removal, radiation treatment of vegetable tanning wastes increases the biodegradability. The results of this study show that radiation treatment of wastes offers a viable method for removing color and increasing biodegradability. An economic analysis, which is also included, indicates that in the near future radiation treatment will be competitive with other advanced waste treatment methods

Studies on the Wood-Based Furniture, Leather Products and Footwear Manufacturing Industries in the Philippines

OpenAIRE

Poblador, Niceto; Solis, Adriano; Ybanez, Roy; Aragon, Bienvenido

1983-01-01

This paper aims to develop both the micro and macro data on the entire range of socioeconomic, managerial and technical issues faced by the wood-based furniture, footwear and leather tanning industry. The studies are intended to provide an initial base for policy formulation and implementation and to evolve a set of relevant guidelines for managerial and technical decisions. Findings show that the wood-based furniture industry is characterized by relative ease of entry that allows manufacture...

Complex Permittivity Measurements of Textiles and Leather in a Free Space: An Angular-Invariant Approach

OpenAIRE

Kapilevich, B.; Litvak, B.; Anisimov, M.; Hardon, D.; Pinhasi, Y.

2012-01-01

The paper describes the complex permittivity measurements of textiles and leathers in a free space at 330 GHz. The destructive role of the Rayleigh scattering effect is considered and the angular-invariant limit for an incidence angle has been found out experimentally within 25–30 degrees. If incidence angle exceeds this critical parameter, the uncertainty caused by the Rayleigh scattering is drastically increased preventing accurate measurements of the real and imaginary parts of a bulky mat...

Populações microbianas em solo agrícola sob aplicação de lodos de curtume Microbial populations affected by the soil disposal of tannery sludge

Directory of Open Access Journals (Sweden)

Luiz Ermindo Cavallet

2008-12-01

estado natural.Tannery residues are potential pollution sources in several regions of Brazil, mainly in the State of Rio Grande do Sul. One of the alternatives for the final destination of the sludge resulting from the waste water treatment of tanning industries is the disposal and recycling in the soil. To evaluate the effects of two waste types originated from primary treatment of tannery residual water on soil microbial populations, an open air pot experiment was carried out in a Paleudult soil with ten percent clay from Estância Velha, Rio Grande do Sul State, Brazil, where several tannery industries are located. Mineral fertilization was compared to sludge application of 15, 30 and 60 t ha-1 of sludge originated either from tannin or Cr tanning agents. One treatment with cattle manure and a control were also included. Chromium soil, organic C concentrations, pH and bacteria, fungi and actinomyces populations were determined. Biological degradation was efficient for sludge with Cr up to 60 t ha-1 level and for tannin sludge up to 30 t ha-1 dose. Except for the sludge with Cr on the fungus population, the bacteria, fungi and actinomyces populations were stimulated by tannery sludge application. Due to the organic matter concentration in the soil, bacteria microbial populations were stimulated more than fungi and actinomyces. Chromium, pH and organic C increased as a result of the soil disposal of tannery sludges. The application of both tannery residues did not decrease the biological degradation process when compared to normal soil levels.

Mineralização do carbono orgânico em solos tratados com lodo de curtume Mineralization of the organic carbon in soils treated with tannery sludges

Directory of Open Access Journals (Sweden)

Alexandre Martin Martines

2006-07-01

Full Text Available O objetivo deste trabalho foi avaliar a mineralização do carbono orgânico do lodo de curtume, aplicado em solos com diferentes classes texturais, de modo a caracterizar a cinética do processo de mineralização e auxiliar na elaboração de normas técnicas sobre o uso agrícola desse material. Foram conduzidos experimentos de incubação por 105 dias, em laboratório, utilizando-se três solos: Nitossolo Vermelho eutroférrico típico (NVef, Latossolo Vermelho-Amarelo distrófico típico (LVAd e Neossolo Quartzarênico órtico típico (RQo. O lodo de curtume utilizado nos experimentos foi composto de uma mistura, na proporção de 1:1, do lodo do caleiro e do lodo primário da estação de tratamento de efluentes, resultante da precipitação dos efluentes gerados no processo, com exceção dos efluentes que contêm cromo. As doses aplicadas (base seca no NVef e LVAd foram equivalentes a 0, 6, 12, 24 e 36 Mg ha-1 e a 0, 3, 6, 12 e 24 Mg ha-1 no RQo. Não se observa prejuízo à atividade microbiana dos solos, avaliada por meio da respiração basal, e a mineralização do carbono adicionado por meio do lodo de curtume é intensa nos primeiros 15 a 20 dias de incubação.The objective of this work was to evaluate the mineralization of the organic carbon derived from the tannery sludge applied in increasing doses on soils with different textures, to evaluate the decomposition kinetics, as well as to learn about the impact of this residue on the soil microbial community. This knowledge will be helpful for the establishment of technical rules about the agricultural use of the tannery sludges. Incubation experiments were carried out in the laboratory for 105 days, using three soils: a Kandiudalfic Eutrudox (NVef, a Typic Hapludox (LVAd and a Typic Quartzipsamment (RQo. Tannery sludge used in these experiments was composed of a mixture of liming sludge and the primary sludge from the wastewater treatment station, in the proportion 1:1, with the

Simulation Analysis of a Fabrication Process of a Tannery: Case Study of a Latin American Company

Directory of Open Access Journals (Sweden)

Carolina Pirachicán-Mayorga

2017-12-01

Full Text Available A large number of real-life optimization problems in economics and business are complex and difficult to solve. Among the solutions techniques available in the Management Sciences, Discrete-Event computer Simulation (DES can be considered as one of the most preferred by practitioners. DES has been used as an analysis tool to evaluate new production system concepts, and has also been used in the operation and planning of manufacturing facilities. In this paper, we propose to apply DES for the analysis of a tannery manufacturing facility. The objective is to analyze the current performance of the production system in order to propose alternatives for improvement, as well as optimum parameters for production. Results obtained showed the advantages of using such a quantitative decision-aid technique by capturing most of the complexity characteristics of the production process.

Green methodology for the recovery of Cr (VI from tannery effluent using newly synthesized quaternary ammonium salt

Directory of Open Access Journals (Sweden)

K.S. Yoganand

2017-02-01

Full Text Available Leather tanning industries release effluents into the river through various canals. These effluents contain chromium (VI contaminating the river and the ground water as well. To fix a solution for this issue a simple and selective solvent extraction method has been applied by using a newly synthesized quaternary ammonium salt viz 2-benzoylethylheptyldimethylammonium bromide. By varying the parameters such as quaternary ammonium salts, sulfuric acid, pH, solvents, equilibration time and aqueous organic ratio the extraction efficiency has been determined.

40 CFR Table 2 to Subpart Tttt of... - Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss 2 Table 2 to Subpart TTTT of Part 63 Protection of Environment... Finishing HAP Emission Limits for Determining the Allowable HAP Loss As required in § 63.5450, you must meet...

MARGINALIZATION OF PARWA LEATHER PUPPET IN GIANYAR REGENCY IN GLOBALIZATION ERA

Directory of Open Access Journals (Sweden)

I Made Yudabakti

2013-12-01

Full Text Available This present study discussed the marginalization of the Parwa Leather Puppet in Gianyar Regency in the globalization era. It discussed the form, the causing factors, and the impact of marginalization. The qualitative interpretative method was used to analyze the problems of the study. The data were collected using the techniques of observation, in-depth interview, documentary study, and library research. The data were qualitatively analyzed. The results of the study showed that there were several forms of marginalization occurring to the Parwa Leather Puppet ‘Wayang Kulit Parwa’ (WKP in Gianyar Regency. This was indicated by the change in the context of performance and indication of marginalization. The forms of the context of performance were made up of the facts that (a the viewers shifted from the young generation to the old generation; (b it used to be performed as an offering but now it was performed as a commodity or comodification; (c technology played more important roles (the lighting, sound system, and the material for making the puppet, and d the accompanying gamelan orchestra changed. Marginalization was indicated by (a the fall in the frequency of performance, (b WKP was getting less popular in the community; (c fewer people were getting interested in WKP performance; and (e WKP was getting less respected. The factors responsible for the marginalization of WKP in Gianyar Regency were the facts that less people were interested in WKP, the decrease in the WKP puppeteer’s activities, the policy issued by the traditional institution was weak, and the supervision made by the local government of Gianyar was weak. In addition, WKP was less prospective; the current community needed more amusement than guidance, the rise in the impact of foreign cultural art, more and more sources of modern amusements were made available, and the impact of telecommunication technology. The marginalization of WKP in Gianyar Regency led to impacts and

40 CFR Table 1 to Subpart Tttt of... - Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Leather Finishing HAP Emission Limits for Determining the Allowable HAP Loss 1 Table 1 to Subpart TTTT of Part 63 Protection of Environment... Finishing HAP Emission Limits for Determining the Allowable HAP Loss As required in §§ 63.5305 and 63.5340(b...

Pollution of the environment by tannery and textile waste waters in the areas of Antananarivo, Madagascar

International Nuclear Information System (INIS)

Rasoazanany, E.O.; Raoelina Andriambololona; Andrianarivo, R.R.; Randriamanivo, L.V.; Raboanary, R.

2007-01-01

Waste water pollution is a major problem throughout the world. It has affected the health and the environment in Antananarivo (capital of Madagascar). Undesirable and toxic heavy metals contained in waste water samples are measured by the technique of total reflection X-ray fluorescence. Chromium is a toxic metal for the environment associated to the tannery. Its concentration (2712.1 μg.L -1 ) is superior to the national norm (2000 μg.L -1 ). Regarding textile factories, the highest value of the conductivity (4670 μS.cm -1 ) is 23 times the national norm (200 μS.cm -1 ). The concentration of lead (251.0 μg.L -1 ) is higher than the national norm (200 μg.L -1 ) and the Belgium norm (100 μg.L -1 ). The present study illustrates the importance of the treatment of waste water of the factories before pouring them in the environment.

Elemental sulfur amendment decreases bio-available Cr-VI in soils impacted by leather tanneries.

Science.gov (United States)

Shi, Jingjing; Chen, Hualin; Arocena, Joselito M; Whitcombe, Todd; Thring, Ronald W; Memiaghe, Jeff Nze

2016-05-01

This study investigated the potential use of elemental S (S(0)) to convert Cr-VI to Cr-III which should decrease the bio-availability hence, toxicity of Cr-VI in soils. The bio-available fraction of Cr in soil was measured by phosphate buffer extraction (PBE) and the results showed that the fraction is about 10% of the total Cr-VI and varied from 12.8 to 42.5 mg kg(-1). The addition of 4.0 mg g(-1) S(0) decreased PBE Cr-VI to soils. Synchrotron-based X-ray absorption near-edge structure (XANES), X-ray fluorescence (XRF) and micro-XRD revealed that Cr-III was the dominant species (99% of total Cr) and Cr was retained by hematite and goethite in soil. Fe-containing minerals may have provided sufficient protection to render the dominant Cr-III species biochemically inert to redox processes in soils. It is concluded that S(0)amendment is a promising approach to remediate Cr-VI contaminated soils. Copyright © 2016 Elsevier Ltd. All rights reserved.

Development of Extraction Methods for the Analysis of Perfluorinated Compounds in Leather with High Performance Liquid Chromatography Tandem Mass Spectrometry

Science.gov (United States)

Zhang, Yan; Wang, Youchao; Tang, Chuanjiang; Nie, Jingmei; Xu, Chengtao

2018-01-01

Perfluorinated compounds (PFCs), used to provide water, oil, grease, heat and stain repellency to a range of textile and other products, have been found to be persistent in the environment and are associated with adverse effects on humans and wildlife. This study presents the development and validation of an analytical method to determine the simultaneous presence of eleven PFCs in leather using solid-phase extraction followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The perfluorinated compounds were primarily extracted from the samples by a liquid extraction procedure by ultrasonic, in which the parameters were optimized. Then the solid-phase extraction (SPE) is the most important advantages of the developed methodology. The sample volume and elution conditions were optimized by means of an experimental design. The proposed method was applied to determine the PFCs in leather, where the detection limits of the eleven compounds were 0.09-0.96 ng/L, and the recoveries of all compounds spiked at 5 ng/L concentration level were in the range of 65-96%, with a better RSD lower than 19% (n = 7).

Kinetic model of the thermal pyrolysis of chrome tanned leather treated with NaOH under different conditions using thermogravimetric analysis.

Science.gov (United States)

Bañón, E; Marcilla, A; García, A N; Martínez, P; León, M

2016-02-01

The thermal decomposition of chrome tanned leather before and after a soaking treatment with NaOH was studied using thermogravimetric analysis (TGA). The effect of the solution concentration (0.2M and 0.5M) and the soaking time (5min and 15min) was evaluated. TGA experiments at four heating rates (5, 10, 15 and 20°Cmin(-1)) were run in a nitrogen atmosphere for every treatment condition. A kinetic model was developed considering the effect of the three variables studied, i.e.: the NaOH solution concentration, the soaking time and the heating rate. The proposed model for chrome tanned leather pyrolysis involves a set of four reactions, i.e.: three independent nth order reactions, yielding the corresponding products and one of them undergoing a successive cero order reaction. The model was successfully applied simultaneously to all the experimental data obtained. The evaluation of the kinetic parameters obtained (activation energy, pre-exponential factor and reaction order) allowed a better understanding of the effect of the alkali treatment on these wastes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enhanced photocatalysts based on Ag-TiO2 and Ag-N-TiO2 nanoparticles for multifunctional leather surface coating

Directory of Open Access Journals (Sweden)

Gaidau Carmen

2016-01-01

Full Text Available The Ag deposition on TiO2 nanoparticles (Ag-TiO2 NPs and N-TiO2 nanoparticles (Ag-N-TiO2 NPs has been made by electrochemical methodology in view of improved antibacterial properties and enhanced photocatalytic activity under visible light irradiation. The particle size in powder and in dispersion showed similar values and good stability in aqueous medium which made them suitable for use in leather surface covering for new multifunctional properties development. The diffuse reflectance spectra of Ag-TiO2 NPs, Ag-N-TiO2 NPs and TiO2 NPs have been investigated and correlated with their photocatalytic performances under UV and visible light against different silver concentrations. The leather surfaces treated with Ag-N-TiO2 NPs showed advanced self-cleaning properties under visible light exposure through the hydrophilic mechanism of organic soil decomposition. Moreover the bacterial sensitivity and proven fungitoxic properties of Ag-N-TiO2 NPs leads to the possibility of designing new multifunctional additives to extend the advanced applications for more durable and useable materials.

Starved air combustion-solidification/stabilization of primary chemical sludge from a tannery

Energy Technology Data Exchange (ETDEWEB)

Swarnalatha, S. [Department of Environmental Technology, Central Leather Research Institute, Adyar, Chennai-600 020, Tamil Nadu (India); Ramani, K. [Department of Environmental Technology, Central Leather Research Institute, Adyar, Chennai-600 020, Tamil Nadu (India); Karthi, A. Geetha [Department of Environmental Technology, Central Leather Research Institute, Adyar, Chennai-600 020, Tamil Nadu (India); Sekaran, G. [Department of Environmental Technology, Central Leather Research Institute, Adyar, Chennai-600 020, Tamil Nadu (India)]. E-mail: ganesansekaran@hotmail.com

2006-09-01

The high concentration of trivalent chromium along with organic/inorganic compounds in tannery sludge causes severe ground water contamination in the case of land disposal and chronic air pollution during incineration. In the present investigation, the sludge was subjected to flow-through column test to evaluate the concentration of leachable organics (tannin, COD and TOC) and heavy metal ions (Cr{sup 3+}, Fe{sup 2+}) present in it. The dried sludge was incinerated at 800 deg. C in an incinerator under starved oxygen supply (starved-air combustion) to prevent the conversion of Cr{sup 3+} to Cr{sup 6+}. The efficiency of starved air combustion was studied under different loading rates of sludge. The calcined sludge was solidified/stabilized using fly ash and Portland cement/gypsum. The solidified bricks were tested for unconfined compressive strength and heavy metal leaching. Unconfined compressive strength of the blocks was in the range of 83-156 kg/cm{sup 2}. The stabilization of chromium (III) in the cement gel matrix was confirmed with scanning electron microscopy (SEM) and X-ray energy dispersive spectroscopy (EDX). Leachability studies on solidified bricks were carried out to determine the metal fixation and dissolved organic (as COD) concentration in the leachate.

Statistical medium optimization of an alkaline protease from Pseudomonas aeruginosa MTCC 10501, its characterization and application in leather processing.

Science.gov (United States)

Boopathy, Naidu Ramachandra; Indhuja, Devadas; Srinivasan, Krishnan; Uthirappan, Mani; Gupta, Rishikesh; Ramudu, Kamini Numbi; Chellan, Rose

2013-04-01

Proteases are shown to have greener mode of application in leather processing for dehairing of goat skins and cow hides. Production of protease by submerged fermentation with potent activity is reported using a new isolate P. aeruginosa MTCC 10501. The production parameters were optimized by statistical methods such as Plackett-Burman and response surface methodology. The optimized production medium contained (g/L); tryptone, 2.5; yeast extract, 3.0; skim milk 30.0; dextrose 1.0; inoculum concentration 4%: initial pH 6.0; incubation temperature 30 degrees C and optimum production at 48 h with protease activity of 7.6 U/mL. The protease had the following characteristics: pH optima, 9.0; temperature optima 50 degrees C; pH stability between 5.0-10.0 and temperature stability between 10-40 degrees C. The protease was observed to have high potential for dehairing of goat skins in the pre- tanning process comparable to that of the chemical process as evidenced by histology. The method offers cleaner processing using enzyme only instead of toxic chemicals in the pre-tanning process of leather manufacture.

Sorption Capacity Measurement of Chlorella Vulgaris and Scenedesmus Acutus to Remove Chromium from Tannery Waste Water

Science.gov (United States)

Ardila, Liliana; Godoy, Rubén; Montenegro, Luis

2017-08-01

Tanning process is a polluting activity due to the release of toxic agents into the environment. One of the most important of those toxic chemicals is chromium. Different alternatives have been proposed for the removal of this metal from tanning waste water which include the optimization of the productive processes, physicochemical and biochemical waste water treatment. In this study, the biological adsorption process of trivalent chromium was carried out in synthetic water and tannery waste water through two types of native green microalgae, called Chlorella vulgaris and Scenedesmus acutus in Free State and immobilized in PVA state. This, considering that cellular wall of microalgae has functional groups like amines and carboxyl that might bind with trivalent chromium. Statistical significance of variables as pH temperature, chromium and algae concentrations was evaluated just like bio sorption capacity of different types of water and kind of bioadsorbent was calculated to determine if this process is a competitive solution comparing to other heavy metal removal processes.

Industrial waste treatment: the leather industry; Tratamiento conjunto de aguas residuales e industriales: caso de las industrias del curtido

Energy Technology Data Exchange (ETDEWEB)

Cortacans Torre, J.A.

1995-07-01

The industrial waste water treatment can be presented alone or together with the urban waste water. There are special industries that cannot treat their effluents together with municipal effluents, for example the leather industry. This industry uses sulfurs and equivalent chromium. The PH value is around 10. This waste water can`t be introduce directly into municipal collectors. This article presents the general recommendations for their treatment.

Chromate Reduction in Serratia marcescens Isolated from Tannery Effluent and Potential Application for Bioremediation of Chromate Pollution

Directory of Open Access Journals (Sweden)

M.A. Mondaca

2002-01-01

Full Text Available Pollution of aquatic systems by heavy metals has resulted in increasing environmental concern because they cannot be biodegraded. One metal that gives reason for concern due to its toxicity is chromium. Cr(VI and Cr(III are the principal forms of chromium found in natural waters. A chromate-resistant strain of the bacterium S. marcescens was isolated from tannery effluent. The strain was able to reduce Cr(VI to Cr(III, and about 80% of chromate was removed from the medium. The reduction seems to occur on the cell surface. Transmission electron microscopic examination of cells revealed that particles were deposited on the outside of bacterial cells. A stable biofilm was formed in less than 10 h, reaching around 1010 cfu attached per milligram of activated carbon. These findings demonstrate that immobilized S. marcescens might be used in industrial waste treatment processes.

Preparation of silica doped titania nanoparticles with thermal stability and photocatalytic properties and their application for leather surface functionalization

Directory of Open Access Journals (Sweden)

Carmen Gaidau

2017-11-01

Full Text Available Doped nanoparticles based on titanium dioxide are of interest for their multifunctional properties and enlarged photocatalytic activity in visible domain. Silica doped titanium dioxide nanoparticles were prepared by hydrothermal method and their structural characteristics and photocatalytic activity were determined, in order to be used for leather coating as alternative to halogen based flame retardants and dry cleaning solvents. A range of concentrations from 2% to 20% silica doped titanium dioxide nanoparticles (% denotes the theoretical weight percent of Si was synthesized and characterized by ICP-OES, FT-IR, UV-vis spectroscopy, XRD, HRTEM and DLS. Titanium dioxide network penetration was supported by Si-O-Ti and OH identification in FT-IR spectra mainly on surface of 10% and 20% silica doped titanium dioxide nanoparticles. The increase of Si-O-Ti bonds with Si dopant concentration acts as efficient barriers against sinterization and growth of TiO2 particles and explains the low particle size identified in HRTEM analyses as compared to undoped TiO2NPs. UV-vis diffuse reflectance spectra of doped titanium dioxide nanoparticles showed the shifting of absorption band to visible domain for 10% silica doped titanium dioxide nanoparticles. The crystallite sizes were calculated from XRD spectra, ranging between 16.2 and 18.1 nm. HRTEM measurement of hydrothermally synthesized titanium dioxide nanoparticles showed anatase crystallites in the range of 8.8–27 nm, while in the 20% silica doped titanium dioxide nanoparticle sample smaller crystallite with sizes between 2.7 nm and 3.5 nm was identified due to the constraints of the SiO2-based amorphous matrix. Nano sizes of 64 nm and 72 nm were found in water dispersions of 10% and 20% silica doped titanium dioxide nanoparticles and the Zeta potentials were of −53.6 mV and −52.9 mV, which indicate very good stabilities. The leather surface treated with composites of film forming polymers

Improved compaction of dried tannery wastewater sludge.

Science.gov (United States)

Della Zassa, M; Zerlottin, M; Refosco, D; Santomaso, A C; Canu, P

2015-12-01

We quantitatively studied the advantages of improving the compaction of a powder waste by several techniques, including its pelletization. The goal is increasing the mass storage capacity in a given storage volume, and reducing the permeability of air and moisture, that may trigger exothermic spontaneous reactions in organic waste, particularly as powders. The study is based on dried sludges from a wastewater treatment, mainly from tanneries, but the indications are valid and useful for any waste in the form of powder, suitable to pelletization. Measurements of bulk density have been carried out at the industrial and laboratory scale, using different packing procedures, amenable to industrial processes. Waste as powder, pellets and their mixtures have been considered. The bulk density of waste as powder increases from 0.64 t/m(3) (simply poured) to 0.74 t/m(3) (tapped) and finally to 0.82 t/m(3) by a suitable, yet simple, packing procedure that we called dispersion filling, with a net gain of 28% in the compaction by simply modifying the collection procedure. Pelletization increases compaction by definition, but the packing of pellets is relatively coarse. Some increase in bulk density of pellets can be achieved by tapping; vibration and dispersion filling are not efficient with pellets. Mixtures of powder and pellets is the optimal packing policy. The best compaction result was achieved by controlled vibration of a 30/70 wt% mixture of powders and pellets, leading to a final bulk density of 1t/m(3), i.e. an improvement of compaction by more than 54% with respect to simply poured powders, but also larger than 35% compared to just pellets. That means increasing the mass storage capacity by a factor of 1.56. Interestingly, vibration can be the most or the least effective procedure to improve compaction of mixtures, depending on characteristics of vibration. The optimal packing (30/70 wt% powders/pellets) proved to effectively mitigate the onset of smouldering

Pembuatan Fruit Leather dari Campuran Buah Sirsak (Annoma Muricata L.)dan Buah Melon (Cucumis Melo L.)

OpenAIRE

Risti, Andika Pranata; Herawati, Netti

2017-01-01

Theaim of this study wasto get the best treatment fruit leather from mixed soursop (Annoma muricata L.) and melon (Cucumis melo L.). The study used a Complete Randomized Design (CRD) with 6 treatments and 3 replications.The treatments were SM1 (soursop 100 : melon 0), SM2 (soursop80 : melon 20), SM3 (soursop60 : melon40), SM4 (soursop40 : melon60) SM5 (soursop20 : melon80) and SM6 (soursop 0 : melon 100). The data were analyzed statistically using ANOVA and DNMRT at 5%. Thestudyshowed that ...

Testes físico-mecânicos e físico-químicos do couro da tilápia vermelha Physical-mechanical and physical-chemical tests of red tilapia leather

Directory of Open Access Journals (Sweden)

L.C. Godoy

2010-04-01

Full Text Available Realizaram-se testes físico-mecânicos e físico-químicos em couro de tilápia vermelha (Oreochromis spp. a fim de testar a sua resistência. As amostras foram distribuídas em delineamento inteiramente ao acaso com dois tratamentos: no T1, procedeu-se à retirada do corpo-de-prova no sentido longitudinal e, no T2, à retirada do corpo-de-prova no sentido transversal. Para os testes de determinação da resistência à tração, alongamento e rasgamento progressivo, foi utilizado o dinamômetro EMIC, com velocidade de afastamento entre as cargas de 100 ± 20mm/min, em ambiente climatizado (± 23ºC e UR do ar de 50%, por 24 horas. A espessura do couro variou de 0,61 a 0,75mm, mas não houve diferença entre os sentidos analisados. O couro apresentou maior resistência à tração no sentido transversal, 25,89N/mm², (PPhysical-mechanical and physical-chemical tests were carried out on red tilapia leather. They were distributed in a completely randomized design with two treatments: T1 = longitudinal body of proof; T2 = transversal body of proof. It was used the EMIC dynamometer for the tests of resistance to traction and elongation and the progressive tearing, with the speed of 100±20mm/min away between the charges, in an acclimatized room (±23°C and relative humidity of 50% during 24 hours. The thickness of the analyzed leathers ranged from 0.61 to 0.75mm, without differing between the analyzed ways. The leather demonstrated a higher resistance to traction in the transversal direction (25.89N/mm² (P<0.01, when compared to the longitudinal one (14.20N/mm². However, the elongation was significantly higher (P<0.05 in the longitudinal direction (80.8% when compared to the transversal (62.6%. There was no significant difference for the progressive tearing between the treatments (longitudinal = 18.56N/mm; transversal = 21.90N/mm. The leather demonstrated a content of 3.8% of chromium oxide, 15.1% of grease, and pH and difference value of 3

Lesões da mosca dos chifres (Haematobia irritans Linnaeus,1758 na pele de bovinos e impacto na indústria do couro Lesions of the horn fly (Haematobia irritans Linnaeus, 1758 on the bovine skin and their impact in leather industry

Directory of Open Access Journals (Sweden)

Luciana Viero da Silva

2002-12-01

,09% tipo "C". Após a aplicação de pastas especiais por profissionais especializados evidenciou-se que as áreas afetadas pela mosca dos chifres onde se observara um grande numero de lesões passaram a ter um aspecto homogêneo e sem marcas. Deve-se salientar que estes couros, mesmo provenientes de animais tratados apresentavam lesões características de outros parasitas como Dermatobia hominis e Boophilus microplus e também lesões provavelmente adquiridas durante o processamento no frigorífico. Estes resultados sugerem que a mosca dos chifres não representa um fator econômico importante para a industria do couro.Twenty two male 2- year- old Ibagé bovines at the beginning of the experiment were selected. They were divided into two groups of 11 bovines each. One group was treated with insecticide at 14 days intervals and the other remained as control. After that the animals were slaughtered and the respective leather sent to the tannery where they were tanned and evaluated in two stages, the Wet-Blue (leather treated in chromium, still humid and bluish and the total tanning. Animals weight, carcasses weight and dressing percentage were recorded and there was no correlation between infestation by the horn fly and those parameters. At slaughter, samples of the flank areas and the back of the animals were collected and processed for histology studies, which revealed the presence of a perivascular inflammatory infiltration with eosinophils and few mononuclear cells (lymphocytes and plasma cells at the superficial dermis in which 16 out of 19 samples (84.21% were mild in 2 out of 19 samples (10.52% were moderate and in 1 out of 19 samples (5. 26% was marked. In the tanning phase called as Wet-blue, the classification of the leathers was as follows: 8 out 22 (36.36% type "A", 10 out of 22 (45.45% type "B", and"4 out of 22 (18.18% type "C. At this point in the group of animals treated with insecticide the areas commonly parasited by the horn fly (flanks and back a few

Bioethanol Quality Improvement of Coffee Fruit Leather

Directory of Open Access Journals (Sweden)

Edahwati Luluk

2016-01-01

Full Text Available Recently, Indonesia’s dependence on petroleum is to be reduced and even eliminated. To overcome the problem of finding the needed alternative materials that can produce ethanol, in this case as a substitute material or a transport fuel mix, boosting the octane number, and gasoline ethanol (gasohol can be conducted. In the red coffee processing (cooking that will produce 65% and 35% of coffee beans, coffee leather waste is a source of organic material with fairly high cellulose content of 46.82%, 3.01% of pectin and 7.68% of lignin. In this case, its existence is abundant in Indonesia and optimally utilized. During the coffee fruit peeling, the peel waste is only used as a mixture of animal feed or simply left to rot. The purpose of this study was to produce and improve the quality of the fruit skin of bioethanol from coffee cellulose. However, to improve the quality of bioethanol, the production of the lignin content in the skin of the coffee fruit should be eliminated or reduced. Hydrolysis process using organosolve method is expected to improve the quality of bioethanol produced. In particular, the use of enzyme Saccharomyces and Zymmomonas will change the resulting sugar into bioethanol. On one hand, by using batch distillation process for 8 hours with Saccharomyces, bioethanol obtains high purity which is 39.79%; on the other hand, by using the same batch distillation process with Zymmomonas, the bioethanol obtains 38.78%.

Removal of Cr(VI) by nanoscale zero-valent iron (nZVI) from soil contaminated with tannery wastes.

Science.gov (United States)

Singh, Ritu; Misra, Virendra; Singh, Rana Pratap

2012-02-01

The illegal disposal of tannery wastes at Rania, Kanpur has resulted in accumulation of hexavalent chromium [Cr(VI)], a toxic heavy metal in soil posing risk to human health and environment. 27 soil samples were collected at various depths from Rania for the assessment of Cr(VI) level in soil. Out of 27 samples, five samples had shown significant level of Cr(VI) with an average concentration of 15.84 mg Kg(-1). Varied doses of nanoscale zero-valent iron (nZVI) were applied on Cr(VI) containing soil samples for remediation of Cr(VI). Results showed that 0.10 g L(-1) nZVI completely reduces Cr(VI) within 120 min following pseudo first order kinetics. Further, to test the efficacy of nZVI in field, soil windrow experiments were performed at the contaminated site. nZVI showed significant Cr(VI) reduction at field also, indicating it an effective tool for managing sites contaminated with Cr(VI).

Pendugaan Umur Simpan Fruit Leather Nangka (Arrtocarpus Heterophyllus) Dengan Penambahan Gum Arab Menggunakan Metode Accelerated Shelf Life Test (Aslt) Model Arrhenius

OpenAIRE

Rahmanto, Sandy Agus; Parnanto, Nur Her Riyadi; Nursiwi, Asri

2014-01-01

Penelitian ini bertujuan untuk mengetahui umur simpan fruit leather nangka dengan Accelerated Shelf Life Testing (ASLT) metodeberdasarkan model Arrhenius. Menentukan umur simpan dengan menggunakan Accelerated Shelf Life Test (ASLT) dilakukandengan mempercepat proses degradasi atau reaksi dalam percobaan, yaitu meningkatkan suhu penyimpanan pada beberapa suhu diatas suhu kamar, sehingga mempercepat umur simpan analisis waktu. Metode ASLT yang digunakan dalam menentukan masakadaluwarsanya fruit...

Determination of Spatial Chromium Contamination of the Environment around Industrial Zones

Science.gov (United States)

Homa, Dereje; Haile, Ermias

2016-01-01

This study was conducted to determine the spatial levels of chromium contamination of water, agricultural soil, and vegetables in the leather tanning industrial areas using spectrophotometric methods. The results showed elevated accumulation of total Cr ranging from 10.85 ± 0.885 mg/L to 39.696 ± 0.326 mg/L, 16.225 ± 0.12 mg/Kg to 1581.667 ± 0.122 mg/Kg, and 1.0758 ± 0.05348 mg/Kg to 11.75 ± 0.206 mg/Kg in water, agricultural soil, and vegetable samples, respectively. The highest levels of chromium (VI) found from the speciation study were 2.23 ± 0.032 mg/Kg and 0.322 ± 0.07 mg/L in soil and water samples, respectively, which decreased with distance from the tannery. Among the vegetables, the highest load of Cr(VI) was detected in onion root (0.048 ± 0.065 mg/Kg) and the lowest (0.004 ± 0.007 mg/Kg) in fruit of green pepper. The detected levels of Cr in all of the suggested samples were above the WHO permissible limits. The variations of the levels Cr(III) and Cr(VI) contamination of the environment with distance from the tannery were statistically significant (p = 0.05). Similarly, significant difference in the levels of Cr among the tested vegetables was recorded. The levels increased with decreasing distance from the effluent channel. PMID:28044079

Determination of Spatial Chromium Contamination of the Environment around Industrial Zones

Directory of Open Access Journals (Sweden)

Dereje Homa

2016-01-01

Full Text Available This study was conducted to determine the spatial levels of chromium contamination of water, agricultural soil, and vegetables in the leather tanning industrial areas using spectrophotometric methods. The results showed elevated accumulation of total Cr ranging from 10.85±0.885 mg/L to 39.696±0.326 mg/L, 16.225±0.12 mg/Kg to 1581.667±0.122 mg/Kg, and 1.0758±0.05348 mg/Kg to 11.75±0.206 mg/Kg in water, agricultural soil, and vegetable samples, respectively. The highest levels of chromium (VI found from the speciation study were 2.23±0.032 mg/Kg and 0.322±0.07 mg/L in soil and water samples, respectively, which decreased with distance from the tannery. Among the vegetables, the highest load of Cr(VI was detected in onion root (0.048±0.065 mg/Kg and the lowest (0.004±0.007 mg/Kg in fruit of green pepper. The detected levels of Cr in all of the suggested samples were above the WHO permissible limits. The variations of the levels Cr(III and Cr(VI contamination of the environment with distance from the tannery were statistically significant (p=0.05. Similarly, significant difference in the levels of Cr among the tested vegetables was recorded. The levels increased with decreasing distance from the effluent channel.

Determination of Spatial Chromium Contamination of the Environment around Industrial Zones.

Science.gov (United States)

Homa, Dereje; Haile, Ermias; Washe, Alemayehu P

2016-01-01

This study was conducted to determine the spatial levels of chromium contamination of water, agricultural soil, and vegetables in the leather tanning industrial areas using spectrophotometric methods. The results showed elevated accumulation of total Cr ranging from 10.85 ± 0.885 mg/L to 39.696 ± 0.326 mg/L, 16.225 ± 0.12 mg/Kg to 1581.667 ± 0.122 mg/Kg, and 1.0758 ± 0.05348 mg/Kg to 11.75 ± 0.206 mg/Kg in water, agricultural soil, and vegetable samples, respectively. The highest levels of chromium (VI) found from the speciation study were 2.23 ± 0.032 mg/Kg and 0.322 ± 0.07 mg/L in soil and water samples, respectively, which decreased with distance from the tannery. Among the vegetables, the highest load of Cr(VI) was detected in onion root (0.048 ± 0.065 mg/Kg) and the lowest (0.004 ± 0.007 mg/Kg) in fruit of green pepper. The detected levels of Cr in all of the suggested samples were above the WHO permissible limits. The variations of the levels Cr(III) and Cr(VI) contamination of the environment with distance from the tannery were statistically significant ( p = 0.05). Similarly, significant difference in the levels of Cr among the tested vegetables was recorded. The levels increased with decreasing distance from the effluent channel.

The footwear factory's assembly sector: opposing organizational structure and quality from the ergonomic work analysis.

Science.gov (United States)

Silva, Kláudia M M N; Coelho, Bernardo G P; Junior, Josemir V S; Faria, Luiz F M; Dutra, Ludmila; Alvarenga, Marília; Roggini, Renan; Echternach, Eliza Helena de Oliveira

2012-01-01

Data from 2006 indicated that Brazilian footwear leather industry was composed of approximately 9,488 formally registered establishments, considering the leather industry, footwear and leather goods. It was responsible for 211,582 people employed. However, in spite of having many employees, this kind of organization found several problems when analyzed from the ergonomics view. With this premise, then, in order to identify bottlenecks and other engineering problems that could cause discomfort and motivation lack among workers, leading directly to the loss of the product quality, the assembly sector of women's shoes factory was characterized.

N-Nitrosamines in the factory environment

Energy Technology Data Exchange (ETDEWEB)

Fajen, J M; Fine, D H; Rounbehler, D P

1980-01-01

Under the NIOSH-sponsored contract, a total of 40 surveys were conducted at 28 manufacturing plants. The industries investigated were the fish, dye, leather, rubber and manufacturers and users of cutting fluids. NDELA, NMOR, NDMA and NDPhA were found in the air of several factories. In a chrome tannery, NDMA was identified at levels as high as 47 micrograms/m3 and NMOR was found at 27 micrograms/m3 in a rubber tire plant. This study has resulted in an increased understanding of man's exposure to exogenous N-nitrosamines. It is conceivable, from the information obtained in this study, that nitrosamine exposure comparable to that in the tire and rubber industry exists in other industries not yet surveyed. NIOSH is continuing its research on nitrosamines in the industrial environment. A full, industry-wide report on the 40 plant surveys is being compiled for publication.

The role of tannins in conventional and membrane treatment of tannery wastewater.

Science.gov (United States)

Munz, G; De Angelis, D; Gori, R; Mori, G; Casarci, M; Lubello, C

2009-05-30

The role that tannins play in tannery wastewater treatment has been evaluated employing a pilot Membrane Bioreactor (MBR) plant and a full scale Conventional Activated Sludge Process (CASP) plant conducted in parallel. The proposed methodology has established the preliminary use of respirometry to examine the biodegradability of a selection of commercial products (synthetic and natural tannins); the subsequent analysis, by means of spectrophotometric reading and RP-IPC (Reverse-Phase Ion-Pair) liquid chromatography, estimates the concentrations of natural tannins and naphthalenesulfonic tanning agents in the influent and effluent samples. The results show that a consistent percentage of the Total Organic Carbon (TOC) in the effluent of the biological phase of the plants is attributable to the presence of natural and synthetic (Sulfonated Naphthalene-Formaldehyde Condensates, SNFC) tannins (17% and 14% respectively). The titrimetric tests that were aimed at evaluating the levels of inhibition on the nitrifying biomass samples did not allow a direct inhibiting effect to be associated with the concentration levels of the tannin in the effluent. Nonetheless, the reduced specific growth rates of ammonium and nitrite oxidising bacteria imply that a strong environmental pressure is present, if not necessarily due to the concentration of tannins, due to the wastewater as a whole. The differences that have emerged by comparing the two technologies (CASP and MBR), in regards to the role that tannins play in terms of biodegradability, did not appear to be significant.

Perfluoroalkyl acids in surface waters and tapwater in the Qiantang River watershed-Influences from paper, textile, and leather industries.

Science.gov (United States)

Lu, Guo-Hui; Gai, Nan; Zhang, Peng; Piao, Hai-Tao; Chen, Shu; Wang, Xiao-Chun; Jiao, Xing-Chun; Yin, Xiao-Cai; Tan, Ke-Yan; Yang, Yong-Liang

2017-10-01

Perfluoroalkyl acids (PFAAs) are widely used as multi-purpose surfactants or water/oil repellents. In order to understand the contamination level and compositional profiles of PFAAs in aqueous environment in textile, leather, and paper making industrial areas, surface waters and tap waters were collected along the watershed of the Qiantang River where China's largest textile, leather, and paper making industrial bases are located. For comparison, surface water and tapwater samples were also collected in Hangzhou and its adjacent areas. 17 PFAAs were analyzed by solid phase extraction-high performance liquid chromatography-tandem mass spectrometry. The results show that the total concentrations of PFAAs (ΣPFAAs) in the Qiantang River waters ranged from 106.1 to 322.9 ng/L, averaging 164.2 ng/L. The contamination levels have been found to be extremely high, comparable to the levels of the most serious PFAA contamination in surface waters of China. The PFAA composition profiles were characterized by the dominant PFOA (average 58.1% of the total PFAAs), and PFHxA (average 18.8%). The ΣPFAAs in tap water ranged from 9.5 to 174.8 ng/L, showing PFAA compositional pattern similar to the surface waters. Good correlations between PFAA composition profiles in tap waters and the surface waters were observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Moisture sorption isotherms and thermodynamic properties of bovine leather

Science.gov (United States)

Fakhfakh, Rihab; Mihoubi, Daoued; Kechaou, Nabil

2018-04-01

This study was aimed at the determination of bovine leather moisture sorption characteristics using a static gravimetric method at 30, 40, 50, 60 and 70 °C. The curves exhibit type II behaviour according to the BET classification. The sorption isotherms fitting by seven equations shows that GAB model is able to reproduce the equilibrium moisture content evolution with water activity for moisture range varying from 0.02 to 0.83 kg/kg d.b (0.9898 thermodynamic properties such as isosteric heat of sorption, sorption entropy, spreading pressure, net integral enthalpy and entropy. Net isosteric heat of sorption and differential entropy were evaluated through direct use of moisture isotherms by applying the Clausius-Clapeyron equation and used to investigate the enthalpy-entropy compensation theory. Both sorption enthalpy and entropy for desorption increase to a maximum with increasing moisture content, and then decrease sharply with rising moisture content. Adsorption enthalpy decreases with increasing moisture content. Whereas, adsorption entropy increases smoothly with increasing moisture content to a maximum of 6.29 J/K.mol. Spreading pressure increases with rising water activity. The net integral enthalpy seemed to decrease and then increase to become asymptotic. The net integral entropy decreased with moisture content increase.

Mildew prevention by radiation for tanned leather 'wet blue'

International Nuclear Information System (INIS)

Tabei, Masae; Ametani, Kazuo; Yoshimura, Keiji; Chonan, Yasumasa.

1990-01-01

For the chrome-tanned pig skin 'Wet Blue', it was attempted to decide the dose range for preventing mildews by gamma-ray and electron beam. With gamma-ray and 1.5 MV electron beam, in the case of the storage at 20degC and the chrome addition of 2%, it was regarded as 8 kGy, and in the case of the storage at 20degC and the chrome addition of 6%, it was regarded as 6 kGy with 1.5 MV electron beam. In this fiscal year, for the purpose of limiting the dose range for mildew prevention further, a series of the tests was performed. The preparation of samples and the observation of appearance during the storage were carried out by Metropolitan Leather Technology Center, and the irradiation and the measurement of dose were performed by Tokyo Metropolitan Isotope Research Center. The results obtained in 1989 are reported. The preparation of the samples is explained. Co-60 gamma-ray of 2∼8 kGy and the electron beam of 2∼8 kGy from a van de Graaff accelerator were irradiated. Moreover, it is desirable to carry out the reproducibility test on the samples of other production lots. (K.I.)

Solid-state fermentation and composting as alternatives to treat hair waste: A life-cycle assessment comparative approach.

Science.gov (United States)

Catalán, Eva; Komilis, Dimitrios; Sánchez, Antoni

2017-07-01

One of the wastes associated with leather production in tannery industries is the hair residue generated during the dehairing process. Hair wastes are mainly dumped or managed through composting but recent studies propose the treatment of hair wastes through solid-state fermentation (SSF) to obtain proteases and compost. These enzymes are suitable for its use in an enzymatic dehairing process, as an alternative to the current chemical dehairing process. In the present work, two different scenarios for the valorization of the hair waste are proposed and assessed by means of life-cycle assessment: composting and SSF for protease production. Detailed data on hair waste composting and on SSF protease production are gathered from previous studies performed by our research group and from a literature survey. Background inventory data are mainly based on Ecoinvent version 3 from software SimaPro® 8. The main aim of this study was to identify which process results in the highest environmental impact. The SSF process was found to have lower environmental impacts than composting, due to the fact that the enzyme use in the dehairing process prevents the use of chemicals traditionally used in the dehairing process. This permits to reformulate an industrial process from the classical approach of waste management to a novel alternative based on circular economy.

Chromium Waste Treatment from Leather Manufacture Using Electron Beam Radiation Technic

International Nuclear Information System (INIS)

Didiek Herhady, R.; Sukarsono, R.

2007-01-01

Leather manufacture chromium waste treatment using chemical methods have an essential disadvantage, because of the production of the secondary contamination of wastes and separated sediments used by reagents. Therefore, a new technique is needed to solve this problem. The aim of the research to learn the advantages of electron beam radiation for chromium waste treatment. Water radiolysis can be produced by the interaction between electron beam and water or liquid substances. This phenomenon produces many reducing agents and ions that could reduce chromium concentrations in the liquid waste. Ethyl alcohol as a scavenger was added in the waste samples, then the pH of varied from 1, 4, 8 to 12, then were irradiated. Irradiation were done by Electron Beam Machine with dose 15, 25, and 35 kGy. After irradiation, chromium concentration in the samples were analyzed by AAS and UV-vis spectrophotometer. The results had shown that chromium could be reduced by high dose electron beam. The optimum reduction of chromium was achieved at liquid waste pH 8 and irradiation dose 35 kGy. (author)

Spectroscopic Characterization and Nanosafety of Ag-Modified Antibacterial Leather and Leatherette.

Science.gov (United States)

Sportelli, Maria Chiara; Picca, Rosaria Anna; Paladini, Federica; Mangone, Annarosa; Giannossa, Lorena Carla; Franco, Cinzia Di; Gallo, Anna Lucia; Valentini, Antonio; Sannino, Alessandro; Pollini, Mauro; Cioffi, Nicola

2017-07-29

The development of antibacterial coatings is of great interest from both industry and the consumer's point of view. In this study, we characterized tanned leather and polyurethane leatherette, typically employed in the automotive and footwear industries, which were modified by photo-deposition of antibacterial silver nanoparticles (AgNPs). Material surface chemical composition was investigated in detail by X-ray photoelectron spectroscopy (XPS). The material's antibacterial capability was checked against Escherichia coli and Staphylococcus aureus , as representative microorganisms in cross transmissions. Due to the presence of silver in a nanostructured form, nanosafety issues were considered, as well. Ionic release in contact media, as well as whole nanoparticle release from treated materials, were quantitatively evaluated, thus providing specific information on potential product nanotoxicity, which was further investigated through cytocompatibility MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assays, also after surface abrasion of the materials. The proved negligible nanoparticle release, as well as the controlled release of antibacterial ions, shed light on the materials' potentialities, in terms of both high activity and safety.

Spectroscopic Characterization and Nanosafety of Ag-Modified Antibacterial Leather and Leatherette

Directory of Open Access Journals (Sweden)

Maria Chiara Sportelli

2017-07-01

Full Text Available The development of antibacterial coatings is of great interest from both industry and the consumer’s point of view. In this study, we characterized tanned leather and polyurethane leatherette, typically employed in the automotive and footwear industries, which were modified by photo-deposition of antibacterial silver nanoparticles (AgNPs. Material surface chemical composition was investigated in detail by X-ray photoelectron spectroscopy (XPS. The material’s antibacterial capability was checked against Escherichia coli and Staphylococcus aureus, as representative microorganisms in cross transmissions. Due to the presence of silver in a nanostructured form, nanosafety issues were considered, as well. Ionic release in contact media, as well as whole nanoparticle release from treated materials, were quantitatively evaluated, thus providing specific information on potential product nanotoxicity, which was further investigated through cytocompatibility MTT (3-(4,5-dimethylthiazol-2-yl-2,5-diphenyltetrazolium bromide assays, also after surface abrasion of the materials. The proved negligible nanoparticle release, as well as the controlled release of antibacterial ions, shed light on the materials’ potentialities, in terms of both high activity and safety.

A pilot plant for removing chromium from residual water of tanneries.

Science.gov (United States)

Landgrave, J

1995-02-01

The purpose of this study is to develop a technical process for removing trivalent chromium from tannery wastewater via precipitation. This process can be considered an alternative that avoids a remediation procedure against the metal presence in industrial wastes. This process was verified in a treatment pilot plant located in León, México handling 10 m3/day of three types of effluents. The effluent streams were separated to facilitate the elimination of pollutants from each one. The process was based on in situ treatment and recycle to reduce problems associated with transportation and confinement of contaminated sludges. Two types of treatment were carried out in the pilot plant: The physical/chemical and biological treatments. Thirty-five experiments were conducted and the studied variables were the pH, type of flocculant, and its dose. The statistical significance of chromium samples was 94.7% for its precipitation and 99.7% for recovery. The objectives established for this phase of the development were accomplished and the overall efficiencies were measured for each stage in the pilot plant. The results were: a) chromium precipitation 99.5% from wastewater stream, b) chromium recovery 99% for recycling, and c) physical/chemical treatment to eliminate grease and fat at least 85% and 65 to 70% for the biological treatment. The tanning of a hide lot (350 pieces) was accomplished using 60% treated and recycled water without affecting the product quality. The recovered chromium liquor was also used in this hide tanning. This technical procedure is also applicable for removing heavy metals in other industrial sectors as well as in reducing water consumption rates, if pertinent adjustments are implemented.

Determination of Polyamine in Leather by Ultra Performance Liquid Chromatography%超高效液相色谱法测定皮革中多胺物质的研究

Institute of Scientific and Technical Information of China (English)

俞凌云; 程玲玲; 张峰; 吴孟茹; 褚乃清; 帅培强

2016-01-01

Leather amino acid decarboxylation can produce polyamine. The decomposition of fur tanning agent assisting dyeing of polyamide polyamine phenolic resin can also produce amines and polyamine material with carcinogenic teratogenic. At present, there is no material for leather established detection method of polyamine. It is by shaking extraction method, pre-column derivatization of polyamines with dansyl chloride and products at 254nm fluorescence region with the maximum absorption. A simple method was followed by performance liquid chromatography which has been developed for the determination of polyamine in leather samples. Under the optimized conditions, the detection limit of the method was from 0.15 mg/L to 0.20 mg/L, and the recovery rate was higher than 94.6%. It could be applied for the determination of polyamine in leather.%皮革中氨基酸脱羧基可产生多胺类物质，毛皮鞣剂助染性聚酰胺多胺酚醛树脂，分解也可产生多胺类物质，多胺类物质具有致癌致畸性，目前国内外没有针对皮革材料建立多胺类物质的检测方法。研究通过振荡提取，超低温离心法净化提取液，柱前多胺与丹磺酰氯衍生，产物在254 nm荧光区处有最大吸收，建立了高效液相色谱检测皮革中多胺物质的方法。在优化的色谱条件下，检测低限在0.15 mg/L～0.20 mg/L，方法的回收率高于94.6%。方法被成功应用于测定皮革中的多胺物质。

In vitro cytotoxicity and genotoxicity of composite mixtures of natural rubber and leather residues used for textile applications.

Science.gov (United States)

Cavalcante, Dalita Gsm; Gomes, Andressa S; Dos Reis, Elton Ap; Danna, Caroline S; Kerche-Silva, Leandra E; Yoshihara, Eidi; Job, Aldo E

2017-06-01

A novel composite material has been developed from natural rubber and leather waste, and a corresponding patent has been filed. This new material may be incorporated into textile and footwear products. However, as leather waste contains chromium, the biocompatibility of this new material and its safety for use in humans must be investigated. The aim of the present study was to investigate the presence of chromium in this new material, determine the amount of each form of chromium present (trivalent or hexavalent), and evaluate the potential cytotoxic and genotoxic effects of the novel composite in two cell lines. The cellular viability was quantified using the MTT3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide reduction method and neutral red uptake assay, and genotoxic damage was analyzed using the comet assay. Our findings indicated that the extracts obtained from the composite were severely cytotoxic to both cell lines tested, and additionally highly genotoxic to MRC-5 cells. These biological responses do not appear to be attributable to the presence of chromium, as the trivalent form was predominantly found to be present in the extracts, indicating that hexavalent chromium is not formed during the production of the novel composite. The incorporation of this new material in applications that do not involve direct contact with the human skin is thus indicated, and it is suggested that the chain of production of this material be studied in order to improve its biocompatibility so that it may safely be used in the textile and footwear industries.

Biotechnological reduction of sulfide in an industrial primary wastewater treatment system: A sustainable and successful case study

Energy Technology Data Exchange (ETDEWEB)

Rajamani, S. [Central Leather Research Institute, Madras (India)

1996-12-31

The leather industry is an important export-oriented industry in India, with more than 3,000 tanneries located in different clusters. Sodium sulfide, a toxic chemical, is used in large quantities to remove hair and excess flesh from hides and skins. Most of the sodium sulfide used in the process is discharged as waste in the effluent, which causes serious environmental problems. Reduction of sulfide in the effluent is generally achieved by means of chemicals in the pretreatment system, which involves aerobic mixing using large amounts of chemicals and high energy, and generating large volumes of sludge. A simple biotechnological system that uses the residual biosludge from the secondary settling tank was developed, and the commercial-scale application established that more than 90% of the sulfide could be reduced in the primary treatment system. In addition to the reduction of sulfide, foul smells, BOD and COD are reduced to a considerable level. 3 refs., 2 figs., 1 tab.

Response surface modeling for optimization heterocatalytic Fenton oxidation of persistence organic pollution in high total dissolved solid containing wastewater.

Science.gov (United States)

Sekaran, G; Karthikeyan, S; Boopathy, R; Maharaja, P; Gupta, V K; Anandan, C

2014-01-01

The rice-husk-based mesoporous activated carbon (MAC) used in this study was precarbonized and activated using phosphoric acid. N2 adsorption/desorption isotherm, X-ray powder diffraction, electron spin resonance, X-ray photoelectron spectroscopy and scanning electron microscopy, transmission electron microscopy, (29)Si-NMR spectroscopy, and diffuse reflectance spectroscopy were used to characterize the MAC. The tannery wastewater carrying high total dissolved solids (TDS) discharged from leather industry lacks biodegradability despite the presence of dissolved protein. This paper demonstrates the application of free electron-rich MAC as heterogeneous catalyst along with Fenton reagent for the oxidation of persistence organic compounds in high TDS wastewater. The heterogeneous Fenton oxidation of the pretreated wastewater at optimum pH (3.5), H2O2 (4 mmol/L), FeSO4[Symbol: see text]7H2O (0.2 mmol/L), and time (4 h) removed chemical oxygen demand, biochemical oxygen demand, total organic carbon and dissolved protein by 86, 91, 83, and 90%, respectively.

Protein design on computers. Five new proteins: Shpilka, Grendel, Fingerclasp, Leather, and Aida.

Science.gov (United States)

Sander, C; Vriend, G; Bazan, F; Horovitz, A; Nakamura, H; Ribas, L; Finkelstein, A V; Lockhart, A; Merkl, R; Perry, L J

1992-02-01

What is the current state of the art in protein design? This question was approached in a recent two-week protein design workshop sponsored by EMBO and held at the EMBL in Heidelberg. The goals were to test available design tools and to explore new design strategies. Five novel proteins were designed: Shpilka, a sandwich of two four-stranded beta-sheets, a scaffold on which to explore variations in loop topology; Grendel, a four-helical membrane anchor, ready for fusion to water-soluble functional domains; Finger-clasp, a dimer of interdigitating beta-beta-alpha units, the simplest variant of the "handshake" structural class; Aida, an antibody binding surface intended to be specific for flavodoxin; Leather--a minimal NAD binding domain, extracted from a larger protein. Each design is available as a set of three-dimensional coordinates, the corresponding amino acid sequence and a set of analytical results. The designs are placed in the public domain for scrutiny, improvement, and possible experimental verification.

Biological reduction of hexavalent chromium and mechanism analysis of detoxification by enterobacter sp. HT1 isolated from tannery effluents, Mongolia

Directory of Open Access Journals (Sweden)

N Marjangul

2014-12-01

Full Text Available Enterobacter sp. HT1, Cr (VI resistant bacterial strain was isolated from the wastewater sample of the tannery in Mongolia. Batch experiments on hexavalent chromium removal was carried out at 10, 20, and 30 mg/L of Cr (VI added as potassium dichromate (K2Cr2O7, at pH 7 and temperature of 30 °C using pure culture of Enterobacter sp. HT1 as inoculum.  The isolated HT1 is capable of reduction nearly 100% of Cr (VI resulting in the decrease of Cr (VI from 10 to 0.2 mg/L within 20 hours. When the concentration of Cr (VI increased to 20 and 30mg/L, almost complete reduction of Cr (VI could achieve after 72 and 96 hours, respectively.DOI: http://doi.dx.org/10.5564/mjc.v15i0.322 Mongolian Journal of Chemistry 15 (41, 2014, p47-52

Características físico-mecânicas do couro de caprinos mestiços Boer e Anglo Nubianos Physical-mechanic characteristics of leather from crossbred Boer and Anglo Nubiano goats

Directory of Open Access Journals (Sweden)

Arturo Bernardo Selaive Villarroel

2004-12-01

Full Text Available As características físico-mecânicas de 22 couros de caprinos mestiços Boer e Anglo Nubianos foram avaliadas para determinação da qualidade quanto à resistência à tração e ao rasgamento. Os animais foram abatidos com idade média de 260 dias e peso corporal de 22,0 kg. Após a esfola, as peles foram pesadas, conservadas por salmouragem e salga e curtidas com sulfato de cromo. Para determinação da resistência à tração e ao rasgamento progressivo, foram retirados das regiões paleta, anca e ventre dos couros semi-acabados seis corpos-de-prova nas posições paralela e perpendicular à linha dorsal. O delineamento experimental utilizado foi o de parcelas subdivididas, tendo como parcelas dois grupos genéticos e como subparcelas o fatorial 2 x 3 (duas posições e três regiões, com três repetições, sendo as médias comparadas pelo teste Tukey. Não houve diferenças significativas de resistência entre os couros de ambos os grupos genéticos para os ensaios de tração e de rasgamento progressivo. Entretanto, observaram-se diferenças significativas entre as regiões paleta, anca e ventre em todos os parâmetros estudados nos ensaios de tração e de rasgamento progressivo, com os maiores valores de espessura, resistência e alongamento encontrados na paleta. Concluiu-se que o uso de reprodutores exóticos da raça Boer ou Anglo Nubiano em cruzamentos, para melhorar a produção de carne dos caprinos da região nordeste, não influencia a qualidade do couro dos animais.The physical-mechanic industry characteristics of 22 crossed goat leathers from native does mated with Anglo Nubian (AG and Boer (BO bucks were studied to evaluate the leather quality by analysis of tension and tear resistance. Animals were slaughtered at average of 260 days of age and 22.0 kg of live body weigth. After skinning, the pelts were weighed, conserved in brine and salted and classified by quality before the chromium-tanned. To evaluate the tension and

Physiological responses to simulated stair climbing in professional firefighters wearing rubber and leather boots.

Science.gov (United States)

Huang, Chun-Jung; Garten, Ryan S; Wade, Chip; Webb, Heather E; Acevedo, Edmund O

2009-09-01

No studies have considered whether a firefighter's boots are a factor influencing physiological responses. The purpose of this study was to examine physiological responses to a fire simulation activity (stair climb) in professional firefighters wearing rubber boots (RB) and leather boots (LB). Twelve professional firefighters participated in two counterbalanced simulated firefighter stair climb (SFSC) sessions, one wearing RB and the other wearing LB. Heart rate, oxygen uptake (VO(2)), expiratory ventilation (V(E)), blood lactate (BLa), salivary cortisol (SCORT), and leg strength were assessed prior to and following a SFSC. LB elicited significantly greater SCORT values and knee flexion time to peak torque. Furthermore, RB revealed significantly greater ankle dorsiflexion peak torque after SFSC. BLa was positively related to knee flexion peak torque after SFSC in the RB. Firefighters when wearing the RB may be more effective at resisting fatigue and increase more force production.

Pengaruh Penambahan Gum Arab Terhadap Karakteristik Fisik, Kimia Dan Organoleptik Fruit and Vegetable Leather Dari Albedo Semangka (Citrullus Vulgaris Schard.) Dan Wortel (Daucus Carota)

OpenAIRE

Putri, Gita Novelia; Parnanto, Nur Her Riyadi; Nursiwi, Asri

2016-01-01

Tujuan penelitian adalah untuk mengetahui pengaruh konsentrasi gum arab (0; 0,3; 0,6; 0,9%) terbaik sebagai bahan pengikatterhadap karakteristik fisik (kekuatan gel), kimia (kadar abu, kadar air, total karoten, kadar serat pangan dan aktivitas air) sertasensori (warna, aroma, rasa, tekstur, dan overall) fruit and vegetable leather albedo semangka dan wortel. Rancangan penelitianyang digunakan pada penelitian ini adalah Rancangan Acak Lengkap (RAL). Dalam penelitian ini, faktor yang mempengaru...

Tratamento de água residuária de curtume com utilização de sementes de moringa (Moringa oleifera L.. = Treatment of residuary water from tannery utilizing moringa(Moringa oleifera L. seeds.

Directory of Open Access Journals (Sweden)

Lucas Moreira Santos

2010-12-01

Full Text Available A partir da comprovação por vários estudos que as sementes de Moringa (Moringa oleifera L. apresentam a capacidade de clarificar e purificar água potencialmente fora de especificações para consumo humano. Objetivou-se com o presente projeto avaliar se a semente de moringa tem capacidade de purificar água residuária de curtume. Foi utilizada água residuária bruta, coletada antes das estações de tratamento de dois curtumes no município de Maringá, Paraná. As sementes de moringa foram obtidas nos municípios de Umuarama e Floraí, Paraná. As sementes foram retiradas do fruto antes do processo de deiscência e trituradas em meio de água destilada. O sistema foi realizado em sistema descontínuo de tratamento, utilizando vasos de 25litros, onde foram utilizados 15 litros de água residuárias de curtume. Foram feitos uma testemunha e três tratamentos com a mesma concentração 8,0 g L-1 variando a fração em função do tempo de 4, 8 e 12 horas. Foram avaliados os parâmetros: pH, nitrogênio amoniacal, turbidez, DBO e DQO. Os melhores resultados obtidos foram no parâmetro nitrogênio. = The evidence from several studies have indicated that the seeds of Moringa (Moringa oleifera L. have the ability to clarify and purify water potentially out of specification for human consumption. The objective of this project was to evaluate whether the seeds of moringa are capable of purifying wastewater from tannery. Untreated wastewater was used, collected before entering the treatment plants of two tanneries in the city of Maringá, Paraná, Brazil. The moringa seeds were collected in the municipalities of Umuarama and Floraí, Paraná, Brazil. Seeds were removed from the fruit before dehiscence and crushed within distilled water. The system was carried out in batch processing, using 25-liter pots, and 15 liters of wastewater from the tannery. One control and three treatments were used. All groups contained the same concentration 8.0 g L-1

Rancang bantun industri kecil suku cadang / komponen kulit teknis untuk industri tekstil

OpenAIRE

Suliestiyah Wiryodiningrat; Dwi Asdono Basuki

1995-01-01

The objective of this research is to find out proses of production and relation between cost, Selling price anda break even point (BEP). Product specification is space parts for Textile industries i.e.Picker, Buffer, Bumper leather, Sweel leather, Box front leather, Stick Bumper and Tension brake leather. The production capacity is 700 units per-day, so that in one year is 210.000 units. The economical analysis showed that Total Captal (fixed capital and working capital) =Rp. 149.189.750.00. ...

Potency of bio-charcoal briquette from leather cassava tubers and industrial sludge

Science.gov (United States)

Citrasari, Nita; Pinatih, Tety A.; Kuncoro, Eko P.; Soegianto, Agoes; Salamun, Irawan, Bambang

2017-06-01

The purpose of this study was to determine the quality of the bio-charcoal briquette with materials from leather cassava tubers and sludge of wastewater treatment plant. The first, bio-charcoal briquette analized stability test and compressive strength. Then, bio-charcoal briquette with best value analyzed for parameter including moisture content, ash content, calorific content, and burned test. The result briquette quality based on compressive strength for bio-charcoal briquettes carbonated water content between 3.8%-4.5% and non-carbonated bio-charcoal briquettes between 5.2%-7.6%. Bio-charcoal carbonation briquette ash content was between 5.30%-7.40% and non-carbonated bio-charcoal briquettes was between 6.86%-7.46%. Bio-charcoal carbonation levels briquettes heated between 578.2 calories/g-1837.7 calories/g and non carbonatedbio-charcoal briquettes between 858.1 calories/g-891.1 calories/g. Carbonated bio-charcoal burned test was between 48-63 minutes and non-carbonated bio-charcoal was between 22-42 minutes. Emissions resulted from the bio-charcoal briquettes for carbonated and non carbonated composition according to the government regulations ESDM No. 047 of 2006 which, at 128 mg/Nm3 and 139 mg/Nm3.

Chromium removal through biosorption and bioaccumulation by bacteria from tannery effluents contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Alam, Mohammad Zubair [Department of Agricultural Microbiology, Faculty of Agricultural Sciences, Aligarh Muslim University, Aligarh (India); Ahmad, Shamim [Microbiology Division, Institute of Ophthalmology, Faculty of Medicine, J.N. Medical College, Aligarh Muslim University, Aligarh (India)

2011-03-15

Four bacterial isolates (two resistant and two sensitive to chromium) were isolated from soil contaminated with tannery effluents at Jajmau (Kanpur), India, and were identified by 16S rDNA gene sequencing as Stenotrophomonas maltophilia, Exiguobacterium sp., Pantoea sp., and Aeromonas sp. Biosorption of chromium by dried and living biomasses was determined in the resistant and sensitive isolates. The effect of pH, initial metal concentration, and contact time on biosorption was studied. At pH 2.5 the living biomass of chromium resistant isolate Exiguobacterium sp. ZM-2 biosorbed maximum amount of Cr{sup 6+} (29.8 mg/g) whereas the dried biomass of this isolate biosorbed 20.1 mg/g at an initial concentration of 100 mg/L. In case of chromate sensitive isolates, much difference was not observed in biosorption capacities between their dried and living biomasses. The maximum biosorption of Cr{sup 3+} was observed at pH 4.5. However, biosorption was identical in resistant and sensitive isolates. The data on chromium biosorption were analyzed using Langmuir and Freundlich isotherm model. The biosorption data of Cr{sup 6+} and Cr{sup 3+} from aqueous solution were better fitted in Langmuir isotherm model compared to Freundlich isotherm model. Metal recovery through desorption was observed better with dried biomasses compared to the living biomasses for both types of chromium ions. Bioaccumulation of chromate was found higher in chromate resistant isolates compared to the chromate sensitive isolates. Transmission electron microscopy confirmed the accumulation of chromium in cytoplasm in the resistant isolates. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)