WorldWideScience

Sample records for learning paths cut

  1. Laser Cutting Tool Path Optimization

    OpenAIRE

    Dewil, Reginald; Cattrysse, Dirk; Vansteenwegen, Pieter

    2011-01-01

    Given a set of irregular parts nested on a metal sheet, minimize the total non- cutting time for the cutter head, cutting all the required elements and returning to the starting location. The problem is modeled as a generalized traveling sales- person problem with special precedence constraints. An initial feasible solution is generated and improved by local moves embedded in a tabu search framework. The proposed algorithm shows promising results in comparison with a commercial...

  2. Modeling of tool path for the CNC sheet cutting machines

    Science.gov (United States)

    Petunin, Aleksandr A.

    2015-11-01

    In the paper the problem of tool path optimization for CNC (Computer Numerical Control) cutting machines is considered. The classification of the cutting techniques is offered. We also propose a new classification of toll path problems. The tasks of cost minimization and time minimization for standard cutting technique (Continuous Cutting Problem, CCP) and for one of non-standard cutting techniques (Segment Continuous Cutting Problem, SCCP) are formalized. We show that the optimization tasks can be interpreted as discrete optimization problem (generalized travel salesman problem with additional constraints, GTSP). Formalization of some constraints for these tasks is described. For the solution GTSP we offer to use mathematical model of Prof. Chentsov based on concept of a megalopolis and dynamic programming.

  3. Tool path strategy and cutting process monitoring in intelligent machining

    Science.gov (United States)

    Chen, Ming; Wang, Chengdong; An, Qinglong; Ming, Weiwei

    2018-06-01

    Intelligent machining is a current focus in advanced manufacturing technology, and is characterized by high accuracy and efficiency. A central technology of intelligent machining—the cutting process online monitoring and optimization—is urgently needed for mass production. In this research, the cutting process online monitoring and optimization in jet engine impeller machining, cranio-maxillofacial surgery, and hydraulic servo valve deburring are introduced as examples of intelligent machining. Results show that intelligent tool path optimization and cutting process online monitoring are efficient techniques for improving the efficiency, quality, and reliability of machining.

  4. SurfCut: Surfaces of Minimal Paths From Topological Structures

    KAUST Repository

    Algarni, Marei Saeed Mohammed

    2018-03-05

    We present SurfCut, an algorithm for extracting a smooth, simple surface with an unknown 3D curve boundary from a noisy image and a seed point. Our method is built on the novel observation that certain ridge curves of a function defined on a front propagated using the Fast Marching algorithm lie on the surface. Our method extracts and cuts these ridges to form the surface boundary. Our surface extraction algorithm is built on the novel observation that the surface lies in a valley of the distance from Fast Marching. We show that the resulting surface is a collection of minimal paths. Using the framework of cubical complexes and Morse theory, we design algorithms to extract these critical structures robustly. Experiments on three 3D datasets show the robustness of our method, and that it achieves higher accuracy with lower computational cost than state-of-the-art.

  5. SurfCut: Surfaces of Minimal Paths From Topological Structures

    KAUST Repository

    Algarni, Marei Saeed Mohammed

    2017-04-30

    We present SurfCut, an algorithm for extracting a smooth, simple surface with an unknown 3D curve boundary from a noisy 3D image and a seed point. Our method is built on the novel observation that certain ridge curves of a function defined on a front propagated using the Fast Marching algorithm lie on the surface. Our method extracts and cuts these ridges to form the surface boundary. Our surface extraction algorithm is built on the novel observation that the surface lies in a valley of the distance from Fast Marching. We show that the resulting surface is a collection of minimal paths. Using the framework of cubical complexes and Morse theory, we design algorithms to extract these critical structures robustly. Experiments on three 3D datasets show the robustness of our method, and that it achieves higher accuracy with lower computational cost than state-of-the-art.

  6. SurfCut: Surfaces of Minimal Paths From Topological Structures

    KAUST Repository

    Algarni, Marei Saeed Mohammed; Sundaramoorthi, Ganesh

    2018-01-01

    We present SurfCut, an algorithm for extracting a smooth, simple surface with an unknown 3D curve boundary from a noisy image and a seed point. Our method is built on the novel observation that certain ridge curves of a function defined on a front propagated using the Fast Marching algorithm lie on the surface. Our method extracts and cuts these ridges to form the surface boundary. Our surface extraction algorithm is built on the novel observation that the surface lies in a valley of the distance from Fast Marching. We show that the resulting surface is a collection of minimal paths. Using the framework of cubical complexes and Morse theory, we design algorithms to extract these critical structures robustly. Experiments on three 3D datasets show the robustness of our method, and that it achieves higher accuracy with lower computational cost than state-of-the-art.

  7. MOCUS, Minimal Cut Sets and Minimal Path Sets from Fault Tree Analysis

    International Nuclear Information System (INIS)

    Fussell, J.B.; Henry, E.B.; Marshall, N.H.

    1976-01-01

    1 - Description of problem or function: From a description of the Boolean failure logic of a system, called a fault tree, and control parameters specifying the minimal cut set length to be obtained MOCUS determines the system failure modes, or minimal cut sets, and the system success modes, or minimal path sets. 2 - Method of solution: MOCUS uses direct resolution of the fault tree into the cut and path sets. The algorithm used starts with the main failure of interest, the top event, and proceeds to basic independent component failures, called primary events, to resolve the fault tree to obtain the minimal sets. A key point of the algorithm is that an and gate alone always increases the number of path sets; an or gate alone always increases the number of cut sets and increases the size of path sets. Other types of logic gates must be described in terms of and and or logic gates. 3 - Restrictions on the complexity of the problem: Output from MOCUS can include minimal cut and path sets for up to 20 gates

  8. Methodologies for tracking learning paths

    DEFF Research Database (Denmark)

    Frølunde, Lisbeth; Gilje, Øystein; Lindstrand, Fredrik

    2009-01-01

    filmmakers: what furthers their interest and/or hinders it, and what learning patterns emerge. The aim of this article is to present and discuss issues regarding the methodology and meth- ods of the study, such as developing a relationship with interviewees when conducting inter- views online (using MSN). We...... suggest two considerations about using online interviews: how the interviewees value the given subject of conversation and their familiarity with being online. The benefit of getting online communication with the young filmmakers offers ease, because it is both practical and appropriates a meeting...

  9. Learning Paths to Offshore Outsourcing

    DEFF Research Database (Denmark)

    Maskell, Peter; Pedersen, Torben; Petersen, Bent

    A corporation’s offshore outsourcing may be seen as the result of a discrete, strategic decision taken in response to an increasing pressure from worldwide competition. However, empirical evidence of a representative cross-sector sample of international Danish firms indicates that offshore sourcing...... in low-cost countries is best described as a learning-by-doing process in which the offshore outsourcing of a corporation goes through a sequence of stages towards sourcing for innovation. Initially, a corporation’s outsourcing is driven by a desire for cost minimization. Over a period of time...... the outsourcing experience lessens the cognitive limitations of decision-makers as to the advantages that can be achieved through outsourcing in low-cost countries: the insourcer/vendor may not only offer cost advantages, but also quality improvement and innovation. The quality improvements that offshore...

  10. Learning to improve path planning performance

    International Nuclear Information System (INIS)

    Chen, Pang C.

    1995-04-01

    In robotics, path planning refers to finding a short. collision-free path from an initial robot configuration to a desired configuratioin. It has to be fast to support real-time task-level robot programming. Unfortunately, current planning techniques are still too slow to be effective, as they often require several minutes, if not hours of computation. To remedy this situation, we present and analyze a learning algorithm that uses past experience to increase future performance. The algorithm relies on an existing path planner to provide solutions to difficult tasks. From these solutions, an evolving sparse network of useful robot configurations is learned to support faster planning. More generally, the algorithm provides a speedup-learning framework in which a slow but capable planner may be improved both cost-wise and capability-wise by a faster but less capable planner coupled with experience. The basic algorithm is suitable for stationary environments, and can be extended to accommodate changing environments with on-demand experience repair and object-attached experience abstraction. To analyze the algorithm, we characterize the situations in which the adaptive planner is useful, provide quantitative bounds to predict its behavior, and confirm our theoretical results with experiments in path planning of manipulators. Our algorithm and analysis are sufficiently, general that they may also be applied to other planning domains in which experience is useful

  11. A Path to Collaborative Strategic Learning

    Energy Technology Data Exchange (ETDEWEB)

    Nancy M. Carlson

    2003-10-01

    Collaborative learning is critical for the future of any organization and must align with the strategic organizational processes that result in products valued by others. To discover these processes, proposal preparation is explored using topic-oriented ethnography, grounded theory, and an innovative addition to qualitative interviewing, called metainquiry. Using interview data from editors, graphic artists, text processors, scientists, engineers, and technical managers, substantive theory emerges. The research discovers the five essential processes of owning, visioning, reviewing, producing, and contributing needed for organizational strategic learning to occur. The dimensions of these processes are made explicit and can be used to gauge the health of any organization. The substantive theory also provides insight into the ability of collaborative learning to evolve, flourish, and adapt to the strategic advantage of the organization. Lastly, actionable goals with ten essential elements emerge that link owning, visioning, reviewing, producing, and contributing as a path for all organizations to follow to promote collaborative learning communities and enhance their competitive advantage.

  12. An empirical typology of hospital nurses' individual learning paths

    NARCIS (Netherlands)

    Poell, R.F.; van der Krogt, F.J.

    2014-01-01

    Background A relatively new theoretical concept is proposed in this paper, namely, the individual learning path. Learning paths are created by individual employees and comprise a set of learning-relevant activities that are both coherent as a whole and meaningful to them. Objectives To explore the

  13. Pareto-path multitask multiple kernel learning.

    Science.gov (United States)

    Li, Cong; Georgiopoulos, Michael; Anagnostopoulos, Georgios C

    2015-01-01

    A traditional and intuitively appealing Multitask Multiple Kernel Learning (MT-MKL) method is to optimize the sum (thus, the average) of objective functions with (partially) shared kernel function, which allows information sharing among the tasks. We point out that the obtained solution corresponds to a single point on the Pareto Front (PF) of a multiobjective optimization problem, which considers the concurrent optimization of all task objectives involved in the Multitask Learning (MTL) problem. Motivated by this last observation and arguing that the former approach is heuristic, we propose a novel support vector machine MT-MKL framework that considers an implicitly defined set of conic combinations of task objectives. We show that solving our framework produces solutions along a path on the aforementioned PF and that it subsumes the optimization of the average of objective functions as a special case. Using the algorithms we derived, we demonstrate through a series of experimental results that the framework is capable of achieving a better classification performance, when compared with other similar MTL approaches.

  14. Approach to Dynamic Assembling of Individualized Learning Paths

    Science.gov (United States)

    Lubchak, Vladimir; Kupenko, Olena; Kuzikov, Borys

    2012-01-01

    E-learning students are generally heterogeneous and have different capabilities knowledge base and needs. The aim of the Sumy State University (SSU) e-learning system project is to cater to these individual needs by assembling individual learning path. This paper shows current situation with e-learning in Ukraine, state-of-art of development of…

  15. An empirical typology of hospital nurses' individual learning paths.

    Science.gov (United States)

    Poell, Rob F; Van der Krogt, Ferd J

    2014-03-01

    A relatively new theoretical concept is proposed in this paper, namely, the individual learning path. Learning paths are created by individual employees and comprise a set of learning-relevant activities that are both coherent as a whole and meaningful to them. To explore the empirical basis of this theoretical concept. A qualitative study involving semi-structured interviews. Two academic medical centers (university hospitals) and two general hospitals in the Netherlands. A total of 89 nurses were involved in the study. Semi-structured interviews were analyzed qualitatively; cluster analysis was then performed on quantified data from the interviews. Four types of learning path emerged, namely, the formal-external, self-directed, social-emotional, and information-oriented learning paths. The relatively new theoretical concept of an individual learning path can be observed in practice and a number of different learning-path types can be distinguished. Nurses were found to create their own learning paths, that is, select a theme that is relevant primarily to themselves, conduct a variety of learning activities around this theme, participate in social contexts that might help them, and mobilize learning facilities provided by their organization. These activities go way beyond the notion of employees as self-directed learners merely in a didactic sense (establishing learning goals, choosing the right learning activities for these goals, evaluating to what extent their goals have been met as a result). The findings can be interpreted as evidence of employees acting strategically when it comes to their professional development. Providers of continuing professional education/development need to take this into account. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Optimizing learning path selection through memetic algorithms

    NARCIS (Netherlands)

    Acampora, G.; Gaeta, M.; Loia, V.; Ritrovato, P.; Salerno, S.

    2008-01-01

    e-Learning is a critical support mechanism for industrial and academic organizations to enhance the skills of employees and students and, consequently, the overall competitiveness in the new economy. The remarkable velocity and volatility of modern knowledge require novel learning methods offering

  17. Cutting-edge research in developing the library of the future new paths for building future services

    CERN Document Server

    Eden, Bradford Lee

    2015-01-01

    Cutting-Edge Research in the 21st-Century Academic Library: New Paths for Building Future Services explores examples of exciting new library services and workflows and provides opportunities for the rest of the library profession to model and adapt for their own communities and patrons.

  18. Cutting

    Science.gov (United States)

    ... Staying Safe Videos for Educators Search English Español Cutting KidsHealth / For Teens / Cutting What's in this article? ... Getting Help Print en español Cortarse What Is Cutting? Emma's mom first noticed the cuts when Emma ...

  19. Intelligent Web-Based Learning System with Personalized Learning Path Guidance

    Science.gov (United States)

    Chen, C. M.

    2008-01-01

    Personalized curriculum sequencing is an important research issue for web-based learning systems because no fixed learning paths will be appropriate for all learners. Therefore, many researchers focused on developing e-learning systems with personalized learning mechanisms to assist on-line web-based learning and adaptively provide learning paths…

  20. E-Learning and Further Education: How do Individual Learning Paths support Personal Learning Processes

    Directory of Open Access Journals (Sweden)

    Bertil Haack

    2010-02-01

    Full Text Available The MOPEM project includes two fixed scenarios that have been defined to convey the idea of "learning paths". Our aim in this paper is to demonstrate the contexts and conditions for flexible learning paths that can be tailored to meet individual needs. The concept of this kind of specialised path is to enable learners to individualise the learning process and to adjust it to their personal needs. We will outline the background and pro- vide examples to explain the concept of learning stations which we use in our four courses: Online Marketing, CRM Systems, Business Communications and Event Marketing. This idea of "freely" combining subject matter naturally leads to the ques- tion of multi-applicability for the learning blocks in various educational contexts. The answers to this question are interest- ing not only in terms of the feasibility of learning paths from a content and didactic point of view, but also with regard to the economic viability of E-Learning or Blended Learning Systems, which ultimately require technical implementation. In addition we will present some first thoughts on the design of a prototype "Content Pool". It would, however, only make sense to develop and implement this within the scope of a follow-up project.

  1. Studies in spatial learning. I. Orientation and the short-cut. 1946.

    Science.gov (United States)

    Tolman, E C; Ritchie, B F; Kalish, D

    1992-12-01

    1. The original rough formulation of the expectancy theory is difficult to distinguish from the alternative stimulus-response doctrines. Part of this difficulty results from the fact that implicit in this rough formulation, is a definition of the matrix "x expects a goal at location L," which makes it equivalent to the matrix "x runs down the practiced path," when certain conditions are fulfilled. Because of this difficulty, we have rejected this definition. 2. We have suggested instead a definition of the matrix "x expects a goal at location L" which makes it equivalent to the matrix "x runs down the path which points directly to the location L," when certain conditions are fulfilled. 3. To determine whether rats will run down such a path, whenever the original path is blocked, we have run 56 female rats in a situation which conformed to these conditions. 4. Thirty-six percent of the rats chose the path which pointed directly towards the location of the goal. The remaining rats were distributed over the other paths in a chance fashion. 5. We have concluded (1) that rats do learn to expect goals in specific locations, (2) that there are important similarities between this behavior and human symbolic behavior, and (3) that these similarities justify our using the word 'expectation' as a name for the disposition to short-cut when the original patch is blocked.

  2. Assessing the Learning Path Specification: a Pragmatic Quality Approach

    NARCIS (Netherlands)

    Janssen, José; Berlanga, Adriana; Heyenrath, Stef; Martens, Harrie; Vogten, Hubert; Finders, Anton; Herder, Eelco; Hermans, Henry; Melero, Javier; Schaeps, Leon; Koper, Rob

    2010-01-01

    Janssen, J., Berlanga, A. J., Heyenrath, S., Martens, H., Vogten, H., Finders, A., Herder, E., Hermans, H., Melero Gallardo, J., Schaeps, L., & Koper, R. (2010). Assessing the Learning Path Specification: a Pragmatic Quality Approach. Journal of Universal Computer Science, 16(21), 3191-3209.

  3. Non-binary decomposition trees - a method of reliability computation for systems with known minimal paths/cuts

    Energy Technology Data Exchange (ETDEWEB)

    Malinowski, Jacek

    2004-05-01

    A coherent system with independent components and known minimal paths (cuts) is considered. In order to compute its reliability, a tree structure T is constructed whose nodes contain the modified minimal paths (cuts) and numerical values. The value of a non-leaf node is a function of its child nodes' values. The values of leaf nodes are calculated from a simple formula. The value of the root node is the system's failure probability (reliability). Subsequently, an algorithm computing the system's failure probability (reliability) is constructed. The algorithm scans all nodes of T using a stack structure for this purpose. The nodes of T are alternately put on and removed from the stack, their data being modified in the process. Once the algorithm has terminated, the stack contains only the final modification of the root node of T, and its value is equal to the system's failure probability (reliability)

  4. Non-binary decomposition trees - a method of reliability computation for systems with known minimal paths/cuts

    International Nuclear Information System (INIS)

    Malinowski, Jacek

    2004-01-01

    A coherent system with independent components and known minimal paths (cuts) is considered. In order to compute its reliability, a tree structure T is constructed whose nodes contain the modified minimal paths (cuts) and numerical values. The value of a non-leaf node is a function of its child nodes' values. The values of leaf nodes are calculated from a simple formula. The value of the root node is the system's failure probability (reliability). Subsequently, an algorithm computing the system's failure probability (reliability) is constructed. The algorithm scans all nodes of T using a stack structure for this purpose. The nodes of T are alternately put on and removed from the stack, their data being modified in the process. Once the algorithm has terminated, the stack contains only the final modification of the root node of T, and its value is equal to the system's failure probability (reliability)

  5. Drosophila learn efficient paths to a food source.

    Science.gov (United States)

    Navawongse, Rapeechai; Choudhury, Deepak; Raczkowska, Marlena; Stewart, James Charles; Lim, Terrence; Rahman, Mashiur; Toh, Alicia Guek Geok; Wang, Zhiping; Claridge-Chang, Adam

    2016-05-01

    Elucidating the genetic, and neuronal bases for learned behavior is a central problem in neuroscience. A leading system for neurogenetic discovery is the vinegar fly Drosophila melanogaster; fly memory research has identified genes and circuits that mediate aversive and appetitive learning. However, methods to study adaptive food-seeking behavior in this animal have lagged decades behind rodent feeding analysis, largely due to the challenges presented by their small scale. There is currently no method to dynamically control flies' access to food. In rodents, protocols that use dynamic food delivery are a central element of experimental paradigms that date back to the influential work of Skinner. This method is still commonly used in the analysis of learning, memory, addiction, feeding, and many other subjects in experimental psychology. The difficulty of microscale food delivery means this is not a technique used in fly behavior. In the present manuscript we describe a microfluidic chip integrated with machine vision and automation to dynamically control defined liquid food presentations and sensory stimuli. Strikingly, repeated presentations of food at a fixed location produced improvements in path efficiency during food approach. This shows that improved path choice is a learned behavior. Active control of food availability using this microfluidic system is a valuable addition to the methods currently available for the analysis of learned feeding behavior in flies. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  6. Knock-Outs, Stick-Outs, Cut-Outs: Clipping Paths Separate Objects from Background.

    Science.gov (United States)

    Wilson, Bradley

    1998-01-01

    Outlines a six-step process that allows computer operators, using Photoshop software, to create "knock-outs" to precisely define the path that will serve to separate the object from the background. (SR)

  7. Training shortest-path tractography: Automatic learning of spatial priors

    DEFF Research Database (Denmark)

    Kasenburg, Niklas; Liptrot, Matthew George; Reislev, Nina Linde

    2016-01-01

    Tractography is the standard tool for automatic delineation of white matter tracts from diffusion weighted images. However, the output of tractography often requires post-processing to remove false positives and ensure a robust delineation of the studied tract, and this demands expert prior...... knowledge. Here we demonstrate how such prior knowledge, or indeed any prior spatial information, can be automatically incorporated into a shortest-path tractography approach to produce more robust results. We describe how such a prior can be automatically generated (learned) from a population, and we...

  8. Automatic NC-Data generation method for 5-axis cutting of turbine-blades by finding Safe heel-angles and adaptive path-intervals

    International Nuclear Information System (INIS)

    Piao, Cheng Dao; Lee, Cheol Soo; Cho, Kyu Zong; Park, Gwang Ryeol

    2004-01-01

    In this paper, an efficient method for generating 5-axis cutting data for a turbine blade is presented. The interference elimination of 5-axis cutting currently is very complicated, and it takes up a lot of time. The proposed method can generate an interference-free tool path, within an allowance range. Generating the cutting data just point to the cutting process and using it to obtain NC data by calculating the feed rate, allows us to maintain the proper feed rate of the 5-axis machine. This paper includes the algorithms for: (1) CL data generation by detecting an interference-free heel angle, (2) finding the optimal tool path interval considering the cusp-height, (3) finding the adaptive feed rate values for each cutter path, and (4) the inverse kinematics depending on the structure of the 5-axis machine, for generating the NC data

  9. ASPECTS REGARDING THE OPTIMUM CUTTING TOOL PATH IN PROCESSING FREE-FORM

    Directory of Open Access Journals (Sweden)

    Florin CHIFAN

    2014-11-01

    Full Text Available This paper describes an approach on tool paths optimization in CAM-type software for milling free forms, with the goal to improve efficiency in processing using CNC machine tools. The methodology proposed in this paper, tackles the problem of mechanical processing in 3 axes using ball nose milling cutters of small diameters, which follows a free form profile. I will consider two cases: the first one considers the ball nose end mill route on a free form with an angle of less than 30°, the second one with a tool path greater than 30°. The main objective of this paper is to determine the optimum angle in order to obtain a better surface roughness, a shorter time of processing and also a higher tool-life, all these by considering all other factors that occurs in the manufacturing process. This will be done by indicating and editing the tool path so that the tools will the minimum entries and exits on the surface of the piece. This will lead to a 10% decrease of the working time.

  10. Cuts, cancellations and the closed time path: The soft leptogenesis example

    International Nuclear Information System (INIS)

    Garbrecht, Björn; Ramsey-Musolf, Michael J.

    2014-01-01

    By including all leading quantum-statistical effects at finite temperature, we show that no net asymmetry of leptons and sleptons is generated from soft leptogenesis, save the possible contribution from the resonant mixing of sneutrinos. This result contrasts with different conclusions appearing in the literature that are based on an incomplete inclusion of quantum statistics. We discuss vertex and wave-function diagrams as well as all different possible kinematic cuts that nominally lead to CP-violating asymmetries. The present example of soft leptogenesis may therefore serve as a paradigm in order to identify more generally applicable caveats relevant to alternative scenarios for baryogenesis and leptogenesis, and it may provide useful guidance in constructing viable models

  11. Cuts, cancellations and the closed time path: The soft leptogenesis example

    Energy Technology Data Exchange (ETDEWEB)

    Garbrecht, Björn, E-mail: garbrecht@tum.de [Physik Department T70, Technische Universität München, James-Franck-Straße, 85748 Garching (Germany); Ramsey-Musolf, Michael J., E-mail: mjrm@physics.wisc.edu [University of Wisconsin-Madison, Madison, WI 53706 (United States); University of Massachusetts-Amherst, Amherst, MA 01003 (United States); California Institute of Technology, Pasadena, CA 91125 (United States)

    2014-05-15

    By including all leading quantum-statistical effects at finite temperature, we show that no net asymmetry of leptons and sleptons is generated from soft leptogenesis, save the possible contribution from the resonant mixing of sneutrinos. This result contrasts with different conclusions appearing in the literature that are based on an incomplete inclusion of quantum statistics. We discuss vertex and wave-function diagrams as well as all different possible kinematic cuts that nominally lead to CP-violating asymmetries. The present example of soft leptogenesis may therefore serve as a paradigm in order to identify more generally applicable caveats relevant to alternative scenarios for baryogenesis and leptogenesis, and it may provide useful guidance in constructing viable models.

  12. Short-cut transport path for Asian dust directly to the Arctic: a case study

    International Nuclear Information System (INIS)

    Huang, Zhongwei; Huang, Jianping; Wang, Shanshan; Zhou, Tian; Jin, Hongchun; Hayasaka, Tadahiro

    2015-01-01

    Asian dust can be transported long distances from the Taklimakan or Gobi desert to North America across the Pacific Ocean, and it has been found to have a significant impact on ecosystems, climate, and human health. Although it is well known that Asian dust is transported all over the globe, there are limited observations reporting Asian dust transported to the Arctic. We report a case study of a large-scale heavy dust storm over East Asia on 19 March 2010, as shown by ground-based and space-borne multi-sensor observations, as well as NCEP/NCAR reanalysis data and HYSPLIT trajectories. Our analysis suggests that Asian dust aerosols were transported from northwest China to the Arctic within 5 days, crossing eastern China, Japan and Siberia before reaching the Arctic. The results indicate that Asian dust can be transported for long distances along a previously unreported transport path. Evidence from other dust events over the past decade (2001–2010) also supports our results, indicating that dust from 25.2% of Asian dust events has potentially been transported directly to the Arctic. The transport of Asian dust to the Arctic is due to cyclones and the enhanced East Asia Trough (EAT), which are very common synoptic systems over East Asia. This suggests that many other large dust events would have generated long-range transport of dust to the Arctic along this path in the past. Thus, Asian dust potentially affects the Arctic climate and ecosystem, making climate change in the Arctic much more complex to be fully understood. (letter)

  13. Determination of cosmic ray (CR) ionization path and iono/atmospheric cut-off energy from CR intervals III, IV and V in the planetary environments

    International Nuclear Information System (INIS)

    Velinov, P.

    2001-01-01

    In this paper are determined the ionization path and cut-off energies of the cosmic ray (CR) nuclei in relation to the general interaction model 'CR - ionosphere-middle atmosphere'. Here the ionization path and the iono/atmospheric cut-off energies of the galactic CR, solar CR and anomalous CR are separately considered in each energetic range, without taking into account the particle transfer from one range in another. This more general approach will be the object of a further paper

  14. E-Learning and Personalized Learning Path: A Proposal Based on the Adaptive Educational Hypermedia System

    Directory of Open Access Journals (Sweden)

    Francesco Colace

    2014-03-01

    Full Text Available The E-Learning is becoming an effective approach for the improving of quality of learning. Many institutions are adopting this approach both to improve their traditional courses both to increase the potential audience. In the last period great attention is paid in the introduction of methodologies and techniques for the adaptation of learning process to the real needs of students. In this scenario the Adaptive Educational Hypermedia System can be an effective approach. Adaptive hypermedia is a promising area of research at the crossroads of hypermedia and adaptive systems. One of the most important fields where this approach can be applied is just the e-Learning. In this context the adaptive learning resources selection and sequencing is recognized as among one of the most interesting research questions. An Adaptive Educational Hypermedia System is composed by services for the management of the Knowledge Space, the definition of a User Model, the observation of student during his learning period and, as previously said, the adaptation of the learning path according to the real needs of the students. In particular the use of ontologyཿs formalism for the modeling of the ཿknowledge space࿝ related to the course can increase the sharable of learning objects among similar courses or better contextualize their role in the course. This paper addresses the design problem of an Adaptive hypermedia system by the definition of methodologies able to manage each its components, In particular an original user, learning contents, tracking strategies and adaptation model are developed. The proposed Adaptive Educational Hypermedia System has been integrated in an e-Learning platform and an experimental campaign has been conducted. In particular the proposed approach has been introduced in three different blended courses. A comparison with traditional approach has been described and the obtained results seem to be very promising.

  15. Learning Path Recommendation Based on Modified Variable Length Genetic Algorithm

    Science.gov (United States)

    Dwivedi, Pragya; Kant, Vibhor; Bharadwaj, Kamal K.

    2018-01-01

    With the rapid advancement of information and communication technologies, e-learning has gained a considerable attention in recent years. Many researchers have attempted to develop various e-learning systems with personalized learning mechanisms for assisting learners so that they can learn more efficiently. In this context, curriculum sequencing…

  16. Feasibility Analysis of Improving On-Campus Learning Paths via a Depth Sensor

    Science.gov (United States)

    Pan, Wen-Fu; Tu, Shih-Chun; Chien, Mei-Ying

    2014-01-01

    This research aims to apply a depth sensor to create a human-body-sensing context for outdoor learning paths; it is conducted by incorporating both quasi-experiment and survey to compare students' cognitive learning outcome within the context and understand students' attitudes toward the context created. The result of ANCOVA indicates that the…

  17. Interactive Learning Environment for Bio-Inspired Optimization Algorithms for UAV Path Planning

    Science.gov (United States)

    Duan, Haibin; Li, Pei; Shi, Yuhui; Zhang, Xiangyin; Sun, Changhao

    2015-01-01

    This paper describes the development of BOLE, a MATLAB-based interactive learning environment, that facilitates the process of learning bio-inspired optimization algorithms, and that is dedicated exclusively to unmanned aerial vehicle path planning. As a complement to conventional teaching methods, BOLE is designed to help students consolidate the…

  18. A Dynamic Hidden Forwarding Path Planning Method Based on Improved Q-Learning in SDN Environments

    Directory of Open Access Journals (Sweden)

    Yun Chen

    2018-01-01

    Full Text Available Currently, many methods are available to improve the target network’s security. The vast majority of them cannot obtain an optimal attack path and interdict it dynamically and conveniently. Almost all defense strategies aim to repair known vulnerabilities or limit services in target network to improve security of network. These methods cannot response to the attacks in real-time because sometimes they need to wait for manufacturers releasing corresponding countermeasures to repair vulnerabilities. In this paper, we propose an improved Q-learning algorithm to plan an optimal attack path directly and automatically. Based on this path, we use software-defined network (SDN to adjust routing paths and create hidden forwarding paths dynamically to filter vicious attack requests. Compared to other machine learning algorithms, Q-learning only needs to input the target state to its agents, which can avoid early complex training process. We improve Q-learning algorithm in two aspects. First, a reward function based on the weights of hosts and attack success rates of vulnerabilities is proposed, which can adapt to different network topologies precisely. Second, we remove the actions and merge them into every state that reduces complexity from O(N3 to O(N2. In experiments, after deploying hidden forwarding paths, the security of target network is boosted significantly without having to repair network vulnerabilities immediately.

  19. A Call to Action for Research in Digital Learning: Learning without Limits of Time, Place, Path, Pace…or Evidence

    Science.gov (United States)

    Cavanaugh, Cathy; Sessums, Christopher; Drexler, Wendy

    2015-01-01

    This essay is a call for rethinking our approach to research in digital learning. It plots a path founded in social trends and advances in education. A brief review of these trends and advances is followed by discussion of what flattened research might look like at scale. Scaling research in digital learning is crucial to advancing understanding…

  20. Machine Learning from Garden Path Sentences: The Application of Computational Linguistics

    Directory of Open Access Journals (Sweden)

    Jiali Du

    2014-12-01

    Full Text Available This paper discusses the application of computational linguistics in the machine learning (ML system for the processing of garden path sentences. ML is closely related to artificial intelligence and linguistic cognition. The rapid and efficient processing of the complex structures is an effective method to test the system. By means of parsing the garden path sentence, we draw a conclusion that the integration of theoretical and statistical methods is helpful for the development of ML system.

  1. Drosophila learn efficient paths to a food source

    OpenAIRE

    Stewart, James; Lim, Terrence; Claridge-Chang, Adam; Wang, Zhiping; Toh, Alicia; Rahman, Mashiur; Navawongse, Rapeechai; Raczkowska, Marlena; Choudhury, Deepak

    2016-01-01

    Elucidating the genetic, and neuronal bases for learned behavior is a central problem in neuroscience. A leading system for neurogenetic discovery is the vinegar fly Drosophila melanogaster; fly memory research has identified genes and circuits that mediate aversive and appetitive learning. However, methods to study adaptive food-seeking behavior in this animal have lagged decades behind rodent feeding analysis, largely due to the challenges presented by their small scale. There is currently ...

  2. Ontology-based concept map learning path reasoning system using SWRL rules

    Energy Technology Data Exchange (ETDEWEB)

    Chu, K.-K.; Lee, C.-I. [National Univ. of Tainan, Taiwan (China). Dept. of Computer Science and Information Learning Technology

    2010-08-13

    Concept maps are graphical representations of knowledge. Concept mapping may reduce students' cognitive load and extend simple memory function. The purpose of this study was on the diagnosis of students' concept map learning abilities and the provision of personally constructive advice dependant on their learning path and progress. Ontology is a useful method with which to represent and store concept map information. Semantic web rule language (SWRL) rules are easy to understand and to use as specific reasoning services. This paper discussed the selection of grade 7 lakes and rivers curriculum for which to devise a concept map learning path reasoning service. The paper defined a concept map e-learning ontology and two SWRL semantic rules, and collected users' concept map learning path data to infer implicit knowledge and to recommend the next learning path for users. It was concluded that the designs devised in this study were feasible and advanced and the ontology kept the domain knowledge preserved. SWRL rules identified an abstraction model for inferred properties. Since they were separate systems, they did not interfere with each other, while ontology or SWRL rules were maintained, ensuring persistent system extensibility and robustness. 15 refs., 1 tab., 8 figs.

  3. Community of Practice: A Path to Strategic Learning

    Energy Technology Data Exchange (ETDEWEB)

    Nancy M. Carlson

    2003-04-01

    To explore the concept of community of practice, the research initially concentrates on a strategic business process in a research and applied engineering laboratory discovering essential communication tools and processes needed to cultivate a high functioning cross-disciplinary team engaged in proposal preparation. Qualitative research in the human ecology of the proposal process blends topic-oriented ethnography and grounded theory and includes an innovative addition to qualitative interviewing, called meta-inquiry. Meta-inquiry uses an initial interview protocol with a homogeneous pool of informants to enhance the researcher's sensitivity to the unique cultures involved in the proposal process before developing a formal interview protocol. In this study the preanalysis process uses data from editors, graphic artists, text processors, and production coordinators to assess, modify, enhance, and focus the formal interview protocol with scientists, engineers, and technical managers-the heterogeneous informants. Thus this human ecology-based interview protocol values homogeneous and heterogeneous informant data and acquires data from which concepts, categories, properties, and both substantive and formal theory emerges. The research discovers the five essential processes of owning, visioning, reviewing, producing, and contributing for strategic learning to occur in a proposal community of practice. The apprenticeship, developmental, and nurturing perspectives of adult learning provide the proposal community of practice with cohesion, interdependence, and caring, while core and boundary practices provide insight into the tacit and explicit dimensions of the proposal process. By making these dimensions explicit, the necessary competencies, absorptive capacity, and capabilities needed for strategic learning are discovered. Substantive theory emerges and provides insight into the ability of the proposal community of practice to evolve, flourish, and adapt to the

  4. Distinguishing butchery cut marks from crocodile bite marks through machine learning methods.

    Science.gov (United States)

    Domínguez-Rodrigo, Manuel; Baquedano, Enrique

    2018-04-10

    All models of evolution of human behaviour depend on the correct identification and interpretation of bone surface modifications (BSM) on archaeofaunal assemblages. Crucial evolutionary features, such as the origin of stone tool use, meat-eating, food-sharing, cooperation and sociality can only be addressed through confident identification and interpretation of BSM, and more specifically, cut marks. Recently, it has been argued that linear marks with the same properties as cut marks can be created by crocodiles, thereby questioning whether secure cut mark identifications can be made in the Early Pleistocene fossil record. Powerful classification methods based on multivariate statistics and machine learning (ML) algorithms have previously successfully discriminated cut marks from most other potentially confounding BSM. However, crocodile-made marks were marginal to or played no role in these comparative analyses. Here, for the first time, we apply state-of-the-art ML methods on crocodile linear BSM and experimental butchery cut marks, showing that the combination of multivariate taphonomy and ML methods provides accurate identification of BSM, including cut and crocodile bite marks. This enables empirically-supported hominin behavioural modelling, provided that these methods are applied to fossil assemblages.

  5. Methodologies for tracking learning paths in the Making a filmmaker research study of young Nordic filmmakers

    DEFF Research Database (Denmark)

    Frølunde, Lisbeth; Lindstrand, Fredrik; Öhman-Gullberg, Lisa

    The aim of this paper is twofold. On the one hand, to present an outline of the ongoing research study Making a filmmaker, which examines how young Nordic filmmakers create their own learning paths along formal and/or informal contexts. Our focus in this paper is especially directed towards issues...

  6. A Sun Path Observation System Based on Augment Reality and Mobile Learning

    Directory of Open Access Journals (Sweden)

    Wernhuar Tarng

    2018-01-01

    Full Text Available This study uses the augmented reality technology and sensor functions of GPS, electronic compass, and three-axis accelerometer on mobile devices to develop a Sun path observation system for applications in astronomy education. The orientation and elevation of the Sun can be calculated by the system according to the user’s location and local time to simulate the Sun path. When holding the mobile device toward the sky, the screen will show the virtual Sun at the same position as that of the real Sun. The user can record the Sun path and the data of observation date, time, longitude, and latitude using the celestial hemisphere and the pole shadow on the system. By setting different observation times and locations, it can be seen that the Sun path changes with seasons and latitudes. The system provides contextual awareness of the Sun path concepts, and it can convert the observation data into organized and meaningful astronomical knowledge to enable combination of situated learning with spatial cognition. The system can solve the problem of being not able to record the Sun path due to a bad weather or topographical restrictions, and therefore it is helpful for elementary students when conducting observations. A teaching experiment has been conducted to analyze the learning achievement of students after using the system, and the results show that it is more effective than traditional teaching aids. The questionnaire results also reveal that the system is easy to operate and useful in recording the Sun path data. Therefore, it is an effective tool for astronomy education in elementary schools.

  7. RSMDP-based Robust Q-learning for Optimal Path Planning in a Dynamic Environment

    Directory of Open Access Journals (Sweden)

    Yunfei Zhang

    2014-07-01

    Full Text Available This paper presents arobust Q-learning method for path planningin a dynamic environment. The method consists of three steps: first, a regime-switching Markov decision process (RSMDP is formed to present the dynamic environment; second a probabilistic roadmap (PRM is constructed, integrated with the RSMDP and stored as a graph whose nodes correspond to a collision-free world state for the robot; and third, an onlineQ-learning method with dynamic stepsize, which facilitates robust convergence of the Q-value iteration, is integrated with the PRM to determine an optimal path for reaching the goal. In this manner, the robot is able to use past experience for improving its performance in avoiding not only static obstacles but also moving obstacles, without knowing the nature of the obstacle motion. The use ofregime switching in the avoidance of obstacles with unknown motion is particularly innovative.  The developed approach is applied to a homecare robot in computer simulation. The results show that the online path planner with Q-learning is able torapidly and successfully converge to the correct path.

  8. Task path planning, scheduling and learning for free-ranging robot systems

    Science.gov (United States)

    Wakefield, G. Steve

    1987-01-01

    The development of robotics applications for space operations is often restricted by the limited movement available to guided robots. Free ranging robots can offer greater flexibility than physically guided robots in these applications. Presented here is an object oriented approach to path planning and task scheduling for free-ranging robots that allows the dynamic determination of paths based on the current environment. The system also provides task learning for repetitive jobs. This approach provides a basis for the design of free-ranging robot systems which are adaptable to various environments and tasks.

  9. On the nature of groundwater flow paths: Observations at fractures and fracture coating at road-cuts

    International Nuclear Information System (INIS)

    Lindberg, A.; Hellmuth, K.-H.

    2001-01-01

    Preliminary investigations were conducted at fractures and their surface coatings exposed along recently quarried road-cuts to the north and east of Helsinki. While (sub)horizontal fractures were usually rare at depths more than a few meters, (sub)vertical fractures were dominating. Fracture fillings/coatings were mostly absent in the formers and generally thin in the latters. Often these fillings/coatings were representative for processes which occurred in the far past at conditions others than present ambient ones. But, on the other hand only a few cases of more intense rock matrix alteration in connection with these processes were observed. Post-glacial weathering has caused at many of the investigated sites surficial oxidation of Fe(II)-rich minerals which has led to mostly thin coatings of fracture surfaces by soft amorphous Fe(III)-oxyhydroxides. Surface coatings were generally homogeneous with fairly even surface structures. It was found that at road-cuts huge areas of undamaged fracture surfaces were accessable to investigations. These can serve for demonstration purposes for the nature of contact surface between groundwater and rock. Despite some oxidation, these exposures give a fairly representative impression of the situation at greater depth where similar fracture types were reported in repository site investigations. (orig.)

  10. Selective influence of prior allocentric knowledge on the kinesthetic learning of a path.

    Science.gov (United States)

    Lafon, Matthieu; Vidal, Manuel; Berthoz, Alain

    2009-04-01

    Spatial cognition studies have described two main cognitive strategies involved in the memorization of traveled paths in human navigation. One of these strategies uses the action-based memory (egocentric) of the traveled route or paths, which involves kinesthetic memory, optic flow, and episodic memory, whereas the other strategy privileges a survey memory of cartographic type (allocentric). Most studies have dealt with these two strategies separately, but none has tried to show the interaction between them in spite of the fact that we commonly use a map to imagine our journey and then proceed using egocentric navigation. An interesting question is therefore: how does prior allocentric knowledge of the environment affect the egocentric, purely kinesthetic navigation processes involved in human navigation? We designed an experiment in which blindfolded subjects had first to walk and memorize a path with kinesthetic cues only. They had previously been shown a map of the path, which was either correct or distorted (consistent shrinking or growing). The latter transformations were studied in order to observe what influence a distorted prior knowledge could have on spatial mechanisms. After having completed the first learning travel along the path, they had to perform several spatial tasks during the testing phase: (1) pointing towards the origin and (2) to specific points encountered along the path, (3) a free locomotor reproduction, and (4) a drawing of the memorized path. The results showed that prior cartographic knowledge influences the paths drawn and the spatial inference capacity, whereas neither locomotor reproduction nor spatial updating was disturbed. Our results strongly support the notion that (1) there are two independent neural bases underlying these mechanisms: a map-like representation allowing allocentric spatial inferences, and a kinesthetic memory of self-motion in space; and (2) a common use of, or a switching between, these two strategies is

  11. Professionalisation in General Adult Education in Germany--An Attempt to Cut a Path through a Jungle

    Science.gov (United States)

    Dausien, Bettina; Schwendowius, Dorothee

    2009-01-01

    The article summarizes the findings of a study on adult learning professions in Europe (ALPINE) commissioned by DG Education and Culture. It explores the current professional and social situation of staff in non-vocational adult education in Germany. It describes the structures and organisations of general adult education in Germany and…

  12. Shoot cuttings propagation of giant reed (Arundo donax L.) in water and moist soil: The path forward?

    Energy Technology Data Exchange (ETDEWEB)

    Ceotto, Enrico; Di Candilo, Mario [C.R.A. - Centro di Ricerca per le Colture Industriali, Via di Corticella 133, 40128 Bologna (Italy)

    2010-11-15

    Giant reed (Arundo donax L.) is a perennial rhizomatous grass that can be regarded as an ideal crop for bioenergy production, owing to several intrinsic characteristics. Despite to the promising yield results obtained in many plot experiments, the cultivation of giant reed at field scale is still a challenge. Owing to the floral sterility of the species, rhizome propagation has been predominantly used to establish field plots experiments, although this method is unpractical and monetarily expensive. Giant reed is a hydrophytic plant that typically spread in riparian systems by flood-mediated fragmentation and dispersal of vegetative propagules. Since giant reed propagation is strictly dependent on temporary abundance of water, this plant characteristic might be exploited for fostering the diffusion of giant reed as a bioenergy field crop. The objectives of this paper were: i) to disseminate some techniques for shoot cutting propagation of giant reed in water and in moist soil; ii) to address the critical points that remain to be solved for a widespread diffusion of this species as a bioenergy field crop. (author)

  13. Vision-based Navigation and Reinforcement Learning Path Finding for Social Robots

    OpenAIRE

    Pérez Sala, Xavier

    2010-01-01

    We propose a robust system for automatic Robot Navigation in uncontrolled en- vironments. The system is composed by three main modules: the Arti cial Vision module, the Reinforcement Learning module, and the behavior control module. The aim of the system is to allow a robot to automatically nd a path that arrives to a pre xed goal. Turn and straight movements in uncontrolled environments are automatically estimated and controlled using the proposed modules. The Arti cial Vi...

  14. Lecturers' and Students’ Perception on Learning Dijkstra’s Shortest Path Algorithm Through Mobile Devices

    Directory of Open Access Journals (Sweden)

    Mazyar Seraj

    2014-06-01

    Full Text Available In recent years, many studies have been carried out on how to engage and support students in e-learning environments. Portable devices such as Personal Digital Assistants (PDAs, Tablet PCs, mobile phones and other mobile equipment have been used as parts of electronic learning environments to facilitate learning and teaching for both lecturers and students. However, there is still a dearth of study investigating the effects of small screen interfaces on mobile-based learning environments. This study aims to address two objectives: (i investigate lecturer and student difficulties encountered in teaching-learning process in traditional face-to-face classroom settings, and (ii to explore lecturer and student perceptions about learning the subject through mobile devices. This paper presents the results of a qualitative study using structured interviews to investigate lecturer and student experiences and perceptions on teaching and learning Dijkstra’s shortest path algorithm via mobile devices. The interview insights were then used as inputs to define user requirements for a mobile learning prototype. The findings show that the lecturers and students raised many issues about interactivity and the flexibility of effective learning applications on small screen devices, especially for a technical subject.

  15. Teaching Service Learning in the Geosciences: An On the Cutting Edge Workshop Report

    Science.gov (United States)

    Bruckner, M. Z.; Laine, E. P.; Mogk, D. W.; O'Connell, S.; Kirk, K. B.

    2010-12-01

    Service learning is an instructional method that combines community service and academic instruction within the context of an established academic course. It is a particularly effective approach that uses active and experiential learning to develop the academic skills required of a course of study and to simultaneously address authentic community needs. Service learning projects can energize and motivate students by engaging a sense of civic responsibility by working in concert with community partners. The geosciences provide abundant opportunities to develop service learning projects on topics related to natural hazards, resources, land use, water quality, community planning, public policy, and education (K-12 and public outreach). To explore the opportunities of teaching service learning in the geosciences, the On the Cutting Edge program convened an online workshop in February 2010. The goals of the workshop were to: 1) introduce the principles and practices of effective service learning instructional activities; 2) provide examples of successful service learning projects and practical advice about "what works;" 3) provide participants with the opportunity to design, develop, and refine their own service learning courses or projects; 4) develop collections of supporting resources related to the pedagogy of service learning; and 5) support a community of scholars interested in continued work on service learning in the geoscience curriculum. The workshop consisted of a series of web-based synchronous and asynchronous sessions, including presentations from experienced practitioners of service learning, panel discussions, threaded discussions, and editable web pages used to develop new material for the website. Time was also provided for small group and individual work and for participants to peer-review each others' service learning projects and to revise their own activities based on reviewer comments. Insights from the workshop were integrated into new web pages

  16. Prediction of laser cutting heat affected zone by extreme learning machine

    Science.gov (United States)

    Anicic, Obrad; Jović, Srđan; Skrijelj, Hivzo; Nedić, Bogdan

    2017-01-01

    Heat affected zone (HAZ) of the laser cutting process may be developed based on combination of different factors. In this investigation the HAZ forecasting, based on the different laser cutting parameters, was analyzed. The main goal was to predict the HAZ according to three inputs. The purpose of this research was to develop and apply the Extreme Learning Machine (ELM) to predict the HAZ. The ELM results were compared with genetic programming (GP) and artificial neural network (ANN). The reliability of the computational models were accessed based on simulation results and by using several statistical indicators. Based upon simulation results, it was demonstrated that ELM can be utilized effectively in applications of HAZ forecasting.

  17. Actively learning human gaze shifting paths for semantics-aware photo cropping.

    Science.gov (United States)

    Zhang, Luming; Gao, Yue; Ji, Rongrong; Xia, Yingjie; Dai, Qionghai; Li, Xuelong

    2014-05-01

    Photo cropping is a widely used tool in printing industry, photography, and cinematography. Conventional cropping models suffer from the following three challenges. First, the deemphasized role of semantic contents that are many times more important than low-level features in photo aesthetics. Second, the absence of a sequential ordering in the existing models. In contrast, humans look at semantically important regions sequentially when viewing a photo. Third, the difficulty of leveraging inputs from multiple users. Experience from multiple users is particularly critical in cropping as photo assessment is quite a subjective task. To address these challenges, this paper proposes semantics-aware photo cropping, which crops a photo by simulating the process of humans sequentially perceiving semantically important regions of a photo. We first project the local features (graphlets in this paper) onto the semantic space, which is constructed based on the category information of the training photos. An efficient learning algorithm is then derived to sequentially select semantically representative graphlets of a photo, and the selecting process can be interpreted by a path, which simulates humans actively perceiving semantics in a photo. Furthermore, we learn a prior distribution of such active graphlet paths from training photos that are marked as aesthetically pleasing by multiple users. The learned priors enforce the corresponding active graphlet path of a test photo to be maximally similar to those from the training photos. Experimental results show that: 1) the active graphlet path accurately predicts human gaze shifting, and thus is more indicative for photo aesthetics than conventional saliency maps and 2) the cropped photos produced by our approach outperform its competitors in both qualitative and quantitative comparisons.

  18. User/Tutor Optimal Learning Path in E-Learning Using Comprehensive Neuro-Fuzzy Approach

    Science.gov (United States)

    Fazlollahtabar, Hamed; Mahdavi, Iraj

    2009-01-01

    Internet evolution has affected all industrial, commercial, and especially learning activities in the new context of e-learning. Due to cost, time, or flexibility e-learning has been adopted by participators as an alternative training method. By development of computer-based devices and new methods of teaching, e-learning has emerged. The…

  19. Displays mounted on cutting blocks reduce the learning curve in navigated total knee arthroplasty.

    Science.gov (United States)

    Schnurr, Christoph; Eysel, Peer; König, Dietmar Pierre

    2011-01-01

    The use of computer navigation in total knee arthroplasty (TKA) improves the implant alignment but increases the operation time. Studies have shown that the operation time is further prolonged due to the surgeon's learning curve, and longer operation times have been associated with higher morbidity risks. It has been our hypothesis that an improvement in the human-machine interface might reduce the time required during the learning curve. Accordingly, we asked whether the use of navigation devices with a display fixed on the surgical instruments would reduce the operation time in navigated TKAs performed by navigation beginners. Thirty medical students were randomized and used two navigation devices in rotation: these were the Kolibri® device with an external display and the Dash® device with a display that was fixed on the cutting blocks. The time for adjustment of the tibial and femoral cutting blocks on knee models while using these devices was measured. A significant time reduction was demonstration when the Dash® device was used: The time reduction was 21% for the tibial block (p = 0.007), 40% for the femoral block (p learning curve may be diminished.

  20. Path to Stochastic Stability: Comparative Analysis of Stochastic Learning Dynamics in Games

    KAUST Repository

    Jaleel, Hassan

    2018-04-08

    Stochastic stability is a popular solution concept for stochastic learning dynamics in games. However, a critical limitation of this solution concept is its inability to distinguish between different learning rules that lead to the same steady-state behavior. We address this limitation for the first time and develop a framework for the comparative analysis of stochastic learning dynamics with different update rules but same steady-state behavior. We present the framework in the context of two learning dynamics: Log-Linear Learning (LLL) and Metropolis Learning (ML). Although both of these dynamics have the same stochastically stable states, LLL and ML correspond to different behavioral models for decision making. Moreover, we demonstrate through an example setup of sensor coverage game that for each of these dynamics, the paths to stochastically stable states exhibit distinctive behaviors. Therefore, we propose multiple criteria to analyze and quantify the differences in the short and medium run behavior of stochastic learning dynamics. We derive and compare upper bounds on the expected hitting time to the set of Nash equilibria for both LLL and ML. For the medium to long-run behavior, we identify a set of tools from the theory of perturbed Markov chains that result in a hierarchical decomposition of the state space into collections of states called cycles. We compare LLL and ML based on the proposed criteria and develop invaluable insights into the comparative behavior of the two dynamics.

  1. PREP KITT, System Reliability by Fault Tree Analysis. PREP, Min Path Set and Min Cut Set for Fault Tree Analysis, Monte-Carlo Method. KITT, Component and System Reliability Information from Kinetic Fault Tree Theory

    International Nuclear Information System (INIS)

    Vesely, W.E.; Narum, R.E.

    1997-01-01

    1 - Description of problem or function: The PREP/KITT computer program package obtains system reliability information from a system fault tree. The PREP program finds the minimal cut sets and/or the minimal path sets of the system fault tree. (A minimal cut set is a smallest set of components such that if all the components are simultaneously failed the system is failed. A minimal path set is a smallest set of components such that if all of the components are simultaneously functioning the system is functioning.) The KITT programs determine reliability information for the components of each minimal cut or path set, for each minimal cut or path set, and for the system. Exact, time-dependent reliability information is determined for each component and for each minimal cut set or path set. For the system, reliability results are obtained by upper bound approximations or by a bracketing procedure in which various upper and lower bounds may be obtained as close to one another as desired. The KITT programs can handle independent components which are non-repairable or which have a constant repair time. Any assortment of non-repairable components and components having constant repair times can be considered. Any inhibit conditions having constant probabilities of occurrence can be handled. The failure intensity of each component is assumed to be constant with respect to time. The KITT2 program can also handle components which during different time intervals, called phases, may have different reliability properties. 2 - Method of solution: The PREP program obtains minimal cut sets by either direct deterministic testing or by an efficient Monte Carlo algorithm. The minimal path sets are obtained using the Monte Carlo algorithm. The reliability information is obtained by the KITT programs from numerical solution of the simple integral balance equations of kinetic tree theory. 3 - Restrictions on the complexity of the problem: The PREP program will obtain the minimal cut and

  2. Language Disorders Are Learning Disabilities: Challenges on the Divergent and Diverse Paths to Language Learning Disability

    Science.gov (United States)

    Sun, Lei; Wallach, Geraldine P.

    2014-01-01

    This article takes readers along the pathway of language learning and disorders across childhood and adolescence, highlighting the complex relationship between early (preschool) language disorders and later (school age) learning disabilities. The discussion starts with a review of diagnostic labels widely used in schools and other professional…

  3. The equivalence of learning paths in early science instruction: effect of direct instruction and discovery learning.

    Science.gov (United States)

    Klahr, David; Nigam, Milena

    2004-10-01

    In a study with 112 third- and fourth-grade children, we measured the relative effectiveness of discovery learning and direct instruction at two points in the learning process: (a) during the initial acquisition of the basic cognitive objective (a procedure for designing and interpreting simple, unconfounded experiments) and (b) during the subsequent transfer and application of this basic skill to more diffuse and authentic reasoning associated with the evaluation of science-fair posters. We found not only that many more children learned from direct instruction than from discovery learning, but also that when asked to make broader, richer scientific judgments, the many children who learned about experimental design from direct instruction performed as well as those few children who discovered the method on their own. These results challenge predictions derived from the presumed superiority of discovery approaches in teaching young children basic procedures for early scientific investigations.

  4. Competence-based multiple learning paths: on the road of implementation

    Directory of Open Access Journals (Sweden)

    María Dolores de Prada

    2014-12-01

    Full Text Available This article presents the results of an action-research implementation project based on a system that weaves together five different routes to facilitate the development of competences through the use of multiple learning paths for primary and secondary teachers. The first and initial results that the article deals with relate to the experience of math teachers for ages 11 to 14. Other levels and other fields are in the process of being developed. The article deals briefly with the justification, the background and the fundamental principles that underpin the research methodology and introduces a number of elements such as the method followed by the research, the resources and the materials used as well as the results obtained at the end of the second year of this experience. It also justifies the model chosen and the criteria and strategies selected for its reliability and verification. In addition, it provides significant elements of reflection about a number of burning issues: The development of a new profile of the “teacher” in a studentcentred system and the implementation system to be followed, the importance of multiple but integrated learning paths and the relevance as well as the reflection on real cases of competence evaluation.

  5. Hard exudates segmentation based on learned initial seeds and iterative graph cut.

    Science.gov (United States)

    Kusakunniran, Worapan; Wu, Qiang; Ritthipravat, Panrasee; Zhang, Jian

    2018-05-01

    (Background and Objective): The occurrence of hard exudates is one of the early signs of diabetic retinopathy which is one of the leading causes of the blindness. Many patients with diabetic retinopathy lose their vision because of the late detection of the disease. Thus, this paper is to propose a novel method of hard exudates segmentation in retinal images in an automatic way. (Methods): The existing methods are based on either supervised or unsupervised learning techniques. In addition, the learned segmentation models may often cause miss-detection and/or fault-detection of hard exudates, due to the lack of rich characteristics, the intra-variations, and the similarity with other components in the retinal image. Thus, in this paper, the supervised learning based on the multilayer perceptron (MLP) is only used to identify initial seeds with high confidences to be hard exudates. Then, the segmentation is finalized by unsupervised learning based on the iterative graph cut (GC) using clusters of initial seeds. Also, in order to reduce color intra-variations of hard exudates in different retinal images, the color transfer (CT) is applied to normalize their color information, in the pre-processing step. (Results): The experiments and comparisons with the other existing methods are based on the two well-known datasets, e_ophtha EX and DIARETDB1. It can be seen that the proposed method outperforms the other existing methods in the literature, with the sensitivity in the pixel-level of 0.891 for the DIARETDB1 dataset and 0.564 for the e_ophtha EX dataset. The cross datasets validation where the training process is performed on one dataset and the testing process is performed on another dataset is also evaluated in this paper, in order to illustrate the robustness of the proposed method. (Conclusions): This newly proposed method integrates the supervised learning and unsupervised learning based techniques. It achieves the improved performance, when compared with the

  6. Analyzing the Learning Path of US Shale Players by Using the Learning Curve Method

    Directory of Open Access Journals (Sweden)

    Jong-Hyun Kim

    2017-12-01

    Full Text Available The US shale exploration and production (E&P industry has grown since 2007 due to the development of new techniques such as hydraulic fracturing and horizontal drilling. As a result, the share of shale gas in the US natural gas production is almost 50%, and the share of tight oil in the US crude oil production is almost 52%. Even though oil and gas prices decreased sharply in 2014, the production amounts of shale gas and tight oil increased between 2014 and 2015. We show that many players in the US shale E&P industry succeeded in decreasing their production costs to maintain their business activity and production. However, most of the companies in the US petroleum E&P industry incurred losses in 2015 and 2016. Furthermore, crude oil and natural gas prices could not rebound to their 2015 price levels. Therefore, many companies in the US petroleum E&P industry need to increase their productivity to overcome the low commodity prices situation. Hence, to test the change in their productivity and analyze their ability to survive in the petroleum industry, this study calculates the learning rate using the US shale E&P players’ annual report data from 2008 to 2016. The result of the calculation is that the long-term learning rate is 1.87% and the short-term learning rate is 3.16%. This indicates a change in the technological development trend.

  7. Self-controlled learning benefits: exploring contributions of self-efficacy and intrinsic motivation via path analysis.

    Science.gov (United States)

    Ste-Marie, Diane M; Carter, Michael J; Law, Barbi; Vertes, Kelly; Smith, Victoria

    2016-09-01

    Research has shown learning advantages for self-controlled practice contexts relative to yoked (i.e., experimenter-imposed) contexts; yet, explanations for this phenomenon remain relatively untested. We examined, via path analysis, whether self-efficacy and intrinsic motivation are important constructs for explaining self-controlled learning benefits. The path model was created using theory-based and empirically supported relationships to examine causal links between these psychological constructs and physical performance. We hypothesised that self-efficacy and intrinsic motivation would have greater predictive power for learning under self-controlled compared to yoked conditions. Participants learned double-mini trampoline progressions, and measures of physical performance, self-efficacy and intrinsic motivation were collected over two practice days and a delayed retention day. The self-controlled group (M = 2.04, SD = .98) completed significantly more skill progressions in retention than their yoked counterparts (M = 1.3, SD = .65). The path model displayed adequate fit, and similar significant path coefficients were found for both groups wherein each variable was predominantly predicted by its preceding time point (e.g., self-efficacy time 1 predicts self-efficacy time 2). Interestingly, the model was not moderated by group; thus, failing to support the hypothesis that self-efficacy and intrinsic motivation have greater predictive power for learning under self-controlled relative to yoked conditions.

  8. The Landsat Image Mosaic of Antarctica (LIMA): A Cutting-Edge Way for Students and Teachers to Learn about Antarctica

    Science.gov (United States)

    Campbell, Brian; Bindschadler, Robert

    2009-01-01

    By studying Antarctica via satellite and through ground-truthing research, we can learn where the ice is melting and why. The Landsat Image Mosaic of Antarctica (LIMA), a new and cutting-edge way for scientists, researchers, educators, students, and the public to look at Antarctica, supports this research and allows for unprecedented views of our…

  9. Teaching learning algorithm based optimization of kerf deviations in pulsed Nd:YAG laser cutting of Kevlar-29 composite laminates

    Science.gov (United States)

    Gautam, Girish Dutt; Pandey, Arun Kumar

    2018-03-01

    Kevlar is the most popular aramid fiber and most commonly used in different technologically advanced industries for various applications. But the precise cutting of Kevlar composite laminates is a difficult task. The conventional cutting methods face various defects such as delamination, burr formation, fiber pullout with poor surface quality and their mechanical performance is greatly affected by these defects. The laser beam machining may be an alternative of the conventional cutting processes due to its non-contact nature, requirement of low specific energy with higher production rate. But this process also faces some problems that may be minimized by operating the machine at optimum parameters levels. This research paper examines the effective utilization of the Nd:YAG laser cutting system on difficult-to-cut Kevlar-29 composite laminates. The objective of the proposed work is to find the optimum process parameters settings for getting the minimum kerf deviations at both sides. The experiments have been conducted on Kevlar-29 composite laminates having thickness 1.25 mm by using Box-Benkhen design with two center points. The experimental data have been used for the optimization by using the proposed methodology. For the optimization, Teaching learning Algorithm based approach has been employed to obtain the minimum kerf deviation at bottom and top sides. A self coded Matlab program has been developed by using the proposed methodology and this program has been used for the optimization. Finally, the confirmation tests have been performed to compare the experimental and optimum results obtained by the proposed methodology. The comparison results show that the machining performance in the laser beam cutting process has been remarkably improved through proposed approach. Finally, the influence of different laser cutting parameters such as lamp current, pulse frequency, pulse width, compressed air pressure and cutting speed on top kerf deviation and bottom kerf

  10. Virtual Workshop Experiences for Faculty: Lessons Learned from On the Cutting Edge

    Science.gov (United States)

    McDaris, J. R.; Kirk, K. B.; Mogk, D. W.; Bruckner, M. Z.

    2010-12-01

    The On the Cutting Edge professional development program for geoscience faculty has begun offering online workshops as a supplement to its face-to-face workshop series. Following a few initial forays since 2005, Cutting Edge launched a suite of four virtual workshops in 2010: Teaching Geoscience with Service Learning, Understanding the Deep Earth, Designing Effective and Innovative Courses in the Geosciences, and Teaching Geoscience Online. Each workshop was presented over 1-2 weeks and included pre-workshop web postings, synchronous whole-group presentations, live small-group discussions, asynchronous input via threaded discussions or editable web pages, and personal time for reflection and writing. Synchronous sessions were facilitated through the Elluminate software platform which includes tools for viewing presentations, screen sharing, real-time participant response, and an ongoing chat-room discussion. Audio was provided through a separate telephone conference service. In addition, many asynchronous conversations on workshop topics were held via a threaded discussion board on the Cutting Edge website and in Wiki-like, editable web pages designed to support collaborative work. A number of challenges to running online workshops exist, primarily involving participants’ time management. It is difficult for participants to set aside enough time to complete workshop activities when they are still enmeshed in their everyday lives. It also requires new skills for speakers, participants and support staff to prepare web-based materials and navigate the technology required for the online presentations. But there are also a number of opportunities presented by these experiences. With no travel needed, an online workshop is less expensive for participants, which allows Cutting Edge to extend its commitment to providing workshop materials to a wider audience of interested faculty. Also, synchronous sessions can be recorded and posted on the website for broader community

  11. Impacts of Different Mobile User Interfaces on Students’ Satisfaction for Learning Dijkstra’s Shortest Path Algorithm

    Directory of Open Access Journals (Sweden)

    Mazyar Seraj

    2014-10-01

    Full Text Available This paper describes an experimental study of learning Dijkstra’s shortest path algorithm on mobile devices. The aim of the study is to investigate and compare the impacts of two different mobile screen user interfaces on students’ satisfaction for learning the technical subject. A mobile learning prototype was developed for learning Dijkstra’s shortest path algorithm on Apple iPhone 4 operated on iPhone operating system (iOS, and Acer Inconia Tab operated on an Android operating system. Thirty students, who are either currently studying or had previously studied Computer Networks, were recruited for the usability trial. At the end of each single session, students’ satisfaction interacting with the two mobile devices was measured using QUIS questionnaire. Although there is no significant difference in students’ satisfaction between the two different mobile screen interfaces, the subjective findings indicate that Acer Inconia Tab gained higher scores as compared to Apple iPhone 4.

  12. Reflexivity and Self-Development of Competencies as Key Drivers in Individuals' Learning and Career Paths: Cases from Italy

    Science.gov (United States)

    Tomassini, Massimo; Zanazzi, Silvia

    2014-01-01

    The article is aimed at analysing the qualitative interviews (in the form of short life stories) carried out within the Learning and Career Paths (LCP) project in Italy. Theories, such as those of reflexivity, agency, self-construction, competencies, and transformation put forward by relevant authors in the sociological and educational field, are…

  13. Relationships between the quality of blended learning experience, self-regulated learning, and academic achievement of medical students: a path analysis.

    Science.gov (United States)

    Kassab, Salah Eldin; Al-Shafei, Ahmad I; Salem, Abdel Halim; Otoom, Sameer

    2015-01-01

    This study examined the relationships between the different aspects of students' course experience, self-regulated learning, and academic achievement of medical students in a blended learning curriculum. Perceptions of medical students (n=171) from the Royal College of Surgeons in Ireland, Medical University of Bahrain (RCSI Bahrain), on the blended learning experience were measured using the Student Course Experience Questionnaire (SCEQ), with an added e-Learning scale. In addition, self-regulated learning was measured using the Motivated Strategies for Learning Questionnaire (MSLQ). Academic achievement was measured by the scores of the students at the end of the course. A path analysis was created to test the relationships between the different study variables. Path analysis indicated that the perceived quality of the face-to-face component of the blended experience directly affected the motivation of students. The SCEQ scale "quality of teaching" directly affected two aspects of motivation: control of learning and intrinsic goal orientation. Furthermore, appropriate course workload directly affected the self-efficacy of students. Moreover, the e-Learning scale directly affected students' peer learning and critical thinking but indirectly affected metacognitive regulation. The resource management regulation strategies, time and study environment, and effort regulation directly affected students' examination scores (17% of the variance explained). However, there were no significant direct relationships between the SCEQ scales and cognitive learning strategies or examination scores. The results of this study will have important implications for designing blended learning courses in medical schools.

  14. Shortest Paths and Vehicle Routing

    DEFF Research Database (Denmark)

    Petersen, Bjørn

    This thesis presents how to parallelize a shortest path labeling algorithm. It is shown how to handle Chvátal-Gomory rank-1 cuts in a column generation context. A Branch-and-Cut algorithm is given for the Elementary Shortest Paths Problem with Capacity Constraint. A reformulation of the Vehicle...... Routing Problem based on partial paths is presented. Finally, a practical application of finding shortest paths in the telecommunication industry is shown....

  15. Physics meets fine arts: a project-based learning path on infrared imaging

    Science.gov (United States)

    Bonanno, A.; Bozzo, G.; Sapia, P.

    2018-03-01

    Infrared imaging represents a noninvasive tool for cultural heritage diagnostics, based on the capability of IR radiation to penetrate the most external layers of different objects (as for example paintings), revealing hidden features of artworks. From an educational viewpoint, this diagnostic technique offers teachers the opportunity to address manifold topics pertaining to the physics and technology of electromagnetic radiation, with particular emphasis on the nature of color and its physical correlates. Moreover, the topic provides interesting interdisciplinary bridges towards the human sciences. In this framework, we present a hands-on learning sequence, suitable for both high school students and university freshmen, inspired by the project-based learning (PBL) paradigm, designed and implemented in the context of an Italian national project aimed at offering students the opportunity to participate in educational activities within a real working context. In a preliminary test we involved a group of 23 high school students while they were working as apprentices in the Laboratory of Applied Physics for Cultural Heritage (ArcheoLab) at the University of Calabria. Consistently with the PBL paradigm, students were given well-defined practical goals to be achieved. As final goals they were asked (i) to construct and to test a low cost device (based on a disused commercial camera) appropriate for performing educational-grade IR investigations on paintings, and (ii) to prepare a device working as a simple spectrometer (recycling the optical components of a disused video projector), suitable for characterizing various light sources in order to identify the most appropriate for infrared imaging. The proposed learning path has shown (in the preliminary test) to be effective in fostering students’ interest towards physics and its technological applications, especially because pupils perceived the context (i.e. physics applied to the protection and restoration of cultural

  16. Supporting Faculty Learning About Teaching: The On the Cutting Edge Website

    Science.gov (United States)

    Fox, S.; Iverson, E. A.; Manduca, C. A.; Kirk, K. B.; McDaris, J. R.; Ormand, C. J.; Bruckner, M. Z.

    2011-12-01

    The On the Cutting Edge website captures information about teaching geoscience from workshop participants and leaders. Designed to both support workshop participants in making use of ideas developed at the workshop and to allow a broader audience to access these ideas, the site includes more than 4900 pages of content in 39 topical collections with more than 1400 community-contributed teaching activities. The site is well used: in 2010, 850,000 visitors made more than one million visits to the site viewing more than 2.1 million pages. To obtain a more detailed understanding of site use within our target population, we interviewed a sample of 30 geoscience faculty. Five primary uses were described repeatedly and in depth: finding ideas for teaching, understanding what colleagues are doing in specific teaching situations, learning about methods, tools, or topic in education or geoscience, finding visualizations, and networking or career planning. Interviewees could describe particular instances where they made use of teaching materials and could cite reasons why they believed this improved student learning. To understand how these uses are manifest in the weblogs, a sample of 73 sessions that lasted at least 10 minutes, and viewed 10 or more pages were selected from March 2009 logs. Sessions were selected to sample heavy use of one or more topical collections, and to sample the diversity of log characteristics. The sessions were described qualitatively and the resulting descriptions categorized. Four recognizable use patterns emerged: activity browsing in some cases combined with study of a pedagogic method, browsing visualizations and associated topical content, digging deep within a particular topical collection, and cross-site browsing. These patterns seem consistent with the uses reported in the interviews. An analysis of characteristics of all sessions in 2008 viewing 10 or more pages indicate that the major uses described in the interview study by 30 faculty

  17. A Model For the Development οf Employees’ Learning (Career Path in Industrial Enterprises

    Directory of Open Access Journals (Sweden)

    G. Chakamian Keshvari

    2018-02-01

    Full Text Available The goal of this study is to propose a model for the development of employees' learning (career path in industrial enterprises. In the research a descriptive-survey method along with field research were used. The statistical population consists of all 110 employees of Dana Baspar's enterprises. A questionnaire with content verified by 30 experts along with the supervisor and the advisor was employed. Related validity of the questionnaires and their stability were 70%, counted by Cronbach's alpha, showing a good level of stability. Descriptive statistics for demographic data (frequency, standard deviation and mean and inferential statistics were used. Research findings show that the influence of workshop and experimental skills gained by apprenticeship, the effect of training by holding meetings and seminars with experts or experience acquired during work is significant and positive on organizational productivity while the mediation variable of professional skills exists but the influence of classic and academic trainings is not positive and significant on organizational productivity considering the existence of mediation variables.

  18. Elucidating the electron transport in semiconductors via Monte Carlo simulations: an inquiry-driven learning path for engineering undergraduates

    International Nuclear Information System (INIS)

    Adorno, Dominique Persano; Pizzolato, Nicola; Fazio, Claudio

    2015-01-01

    Within the context of higher education for science or engineering undergraduates, we present an inquiry-driven learning path aimed at developing a more meaningful conceptual understanding of the electron dynamics in semiconductors in the presence of applied electric fields. The electron transport in a nondegenerate n-type indium phosphide bulk semiconductor is modelled using a multivalley Monte Carlo approach. The main characteristics of the electron dynamics are explored under different values of the driving electric field, lattice temperature and impurity density. Simulation results are presented by following a question-driven path of exploration, starting from the validation of the model and moving up to reasoned inquiries about the observed characteristics of electron dynamics. Our inquiry-driven learning path, based on numerical simulations, represents a viable example of how to integrate a traditional lecture-based teaching approach with effective learning strategies, providing science or engineering undergraduates with practical opportunities to enhance their comprehension of the physics governing the electron dynamics in semiconductors. Finally, we present a general discussion about the advantages and disadvantages of using an inquiry-based teaching approach within a learning environment based on semiconductor simulations. (paper)

  19. Elucidating the electron transport in semiconductors via Monte Carlo simulations: an inquiry-driven learning path for engineering undergraduates

    Science.gov (United States)

    Persano Adorno, Dominique; Pizzolato, Nicola; Fazio, Claudio

    2015-09-01

    Within the context of higher education for science or engineering undergraduates, we present an inquiry-driven learning path aimed at developing a more meaningful conceptual understanding of the electron dynamics in semiconductors in the presence of applied electric fields. The electron transport in a nondegenerate n-type indium phosphide bulk semiconductor is modelled using a multivalley Monte Carlo approach. The main characteristics of the electron dynamics are explored under different values of the driving electric field, lattice temperature and impurity density. Simulation results are presented by following a question-driven path of exploration, starting from the validation of the model and moving up to reasoned inquiries about the observed characteristics of electron dynamics. Our inquiry-driven learning path, based on numerical simulations, represents a viable example of how to integrate a traditional lecture-based teaching approach with effective learning strategies, providing science or engineering undergraduates with practical opportunities to enhance their comprehension of the physics governing the electron dynamics in semiconductors. Finally, we present a general discussion about the advantages and disadvantages of using an inquiry-based teaching approach within a learning environment based on semiconductor simulations.

  20. An investigation of motor learning during side-step cutting, design of a randomised controlled trial

    Directory of Open Access Journals (Sweden)

    Lemmink Koen APM

    2010-10-01

    Full Text Available Abstract Background Of all athletic knee injuries an anterior cruciate ligament (ACL rupture results in the longest time loss from sport. Regardless of the therapy chosen, conservative or reconstructive, athletes are often forced to reduce their level of physical activity and their involvement in sport. Moreover, a recent review reported prevalences of osteoarthritis ranging from 0% to 13% for patients with isolated ACL-deficient (ACL-D knees and respectively 21% to 48% in patients with combined injuries. The need for ACL injury prevention is clear. The identification of risk factors and the development of prevention strategies may therefore have widespread health and economic implications. The focus of this investigation is to assess the role of implicit and explicit motor learning in optimising the performance of a side-step-cutting task. Methods/design A randomized controlled laboratory study will be conducted. Healthy basketball players, females and males, 18 years and older, with no previous lower extremity injuries, playing at the highest recreational level will be included. Subjects will receive a dynamic feedback intervention. Kinematic and kinetic data of the hip, knee and ankle and EMG activity of the quadriceps, hamstrings and gastrocnemius will be recorded. Discussion Female athletes have a significantly higher risk of sustaining an ACL injury than male athletes. Poor biomechanical and neuromuscular control of the lower limb is suggested to be a primary risk factor of an ACL injury mechanism in females. This randomized controlled trial has been designed to investigate whether individual feedback on task performance appears to be an effective intervention method. Results and principles found in this study will be applied to future ACL injury prevention programs, which should maybe more focus on individual injury predisposition. Trial registration Trial registration number NTR2250.

  1. Avoiding Misinterpretations of Piaget and Vygotsky: Mathematical Teaching without Learning, Learning without Teaching, or Helpful Learning-Path Teaching?

    Science.gov (United States)

    Fuson, Karen C.

    2009-01-01

    This article provides an overview of some perspectives about special issues in classroom mathematical teaching and learning that have stemmed from the huge explosion of research in children's mathematical thinking stimulated by Piaget. It concentrates on issues that are particularly important for less-advanced learners and for those who might be…

  2. ASEAN’s Path to Regional Autonomy: Lessons Learned from the European Union

    Science.gov (United States)

    2016-04-04

    ASEAN. ASEAN’s Path to Regional Autonomy 12 Both the 1997 Asian Financial Crisis and ASEAN expansion to Myanmar made it clear that something...From - To) 04/04/2016 Master’s of Military Studies SEP 2015 -APR 2016 4. TITLE AND SUBTITLE Sa. CONTRACT NUMBER ASEAN’s Path to Regional Autonomy ...greater autonomy by enhancing military interoperability, making ASEAN the primary hub for diplomatic arrangements with non-members, transitioning to a

  3. Path Creation

    DEFF Research Database (Denmark)

    Karnøe, Peter; Garud, Raghu

    2012-01-01

    This paper employs path creation as a lens to follow the emergence of the Danish wind turbine cluster. Supplier competencies, regulations, user preferences and a market for wind power did not pre-exist; all had to emerge in a tranformative manner involving multiple actors and artefacts. Competenc......This paper employs path creation as a lens to follow the emergence of the Danish wind turbine cluster. Supplier competencies, regulations, user preferences and a market for wind power did not pre-exist; all had to emerge in a tranformative manner involving multiple actors and artefacts....... Competencies emerged through processes and mechanisms such as co-creation that implicated multiple learning processes. The process was not an orderly linear one as emergent contingencies influenced the learning processes. An implication is that public policy to catalyse clusters cannot be based...

  4. Genetic Learning of Fuzzy Expert Systems for Decision Support in the Automated Process of Wooden Boards Cutting

    Directory of Open Access Journals (Sweden)

    Yaroslav MATSYSHYN

    2014-03-01

    Full Text Available Sawing solid wood (lumber, wooden boards into blanks is an important technological operation, which has significant influence on the efficiency of the woodworking industry as a whole. Selecting a rational variant of lumber cutting is a complex multicriteria problem with many stochastic factors, characterized by incomplete information and fuzzy attributes. About this property by currently used automatic optimizing cross-cut saw is not always rational use of wood raw material. And since the optimization algorithms of these saw functions as a “black box”, their improvement is not possible. Therefore topical the task of developing a new approach to the optimal cross-cutting that takes into account stochastic properties of wood as a material from biological origin. Here we propose a new approach to the problem of lumber optimal cutting in the conditions of uncertainty of lumber quantity and fuzziness lengths of defect-free areas. To account for these conditions, we applied the methods of fuzzy sets theory and used a genetic algorithm to simulate the process of human learning in the implementation the technological operation. Thus, the rules of behavior with yet another defect-free area is defined in fuzzy expert system that can be configured to perform specific production tasks using genetic algorithm. The author's implementation of the genetic algorithm is used to set up the parameters of fuzzy expert system. Working capacity of the developed system verified on simulated and real-world data. Implementation of this approach will make it suitable for the control of automated or fully automatic optimizing cross cutting of solid wood.

  5. Hybrid and Blended Learning: Modifying Pedagogy across Path, Pace, Time, and Place

    Science.gov (United States)

    O'Byrne, W. Ian; Pytash, Kristine E.

    2015-01-01

    Hybrid or blended learning is defined as a pedagogical approach that includes a combination of face-to-face instruction with computer-mediated instruction. The terms "blended learning", "hybrid learning", and "mixed-mode learning" are used interchangeably in current research; however, in the United States,…

  6. The Effect of Trail Pheromone and Path Confinement on Learning of Complex Routes in the Ant Lasius niger.

    Science.gov (United States)

    Czaczkes, Tomer J; Weichselgartner, Tobias; Bernadou, Abel; Heinze, Jürgen

    2016-01-01

    Route learning is key to the survival of many central place foragers, such as bees and many ants. For ants which lay pheromone trails, the presence of a trail may act as an important source of information about whether an error has been made. The presence of trail pheromone has been demonstrated to support route learning, and the effect of pheromones on route choice have been reported to persist even after the pheromones have been removed. This could be explained in two ways: the pheromone may constrain the ants onto the correct route, thus preventing errors and aiding learning. Alternatively, the pheromones may act as a 'reassurance', signalling that the learner is on the right path and that learning the path is worthwhile. Here, we disentangle pheromone presence from route confinement in order to test these hypotheses, using the ant Lasius niger as a model. Unexpectedly, we did not find any evidence that pheromones support route learning. Indeed, there was no evidence that ants confined to the correct route learned at all. Thus, while we cannot support the 'reassurance' hypothesis, we can rule out the 'confinement' hypothesis. Other findings, such as a reduction in pheromone deposition in the presence of trail pheromones, are remarkably consistent with previous experiments. As previously reported, ants which make errors on their outward journey upregulate pheromone deposition on their return. Surprisingly, ants which would go on to make an error down-regulate pheromone deposition on their outward journey, hinting at a capacity for ants to gauge the quality of their own memories.

  7. The Effect of Trail Pheromone and Path Confinement on Learning of Complex Routes in the Ant Lasius niger.

    Directory of Open Access Journals (Sweden)

    Tomer J Czaczkes

    Full Text Available Route learning is key to the survival of many central place foragers, such as bees and many ants. For ants which lay pheromone trails, the presence of a trail may act as an important source of information about whether an error has been made. The presence of trail pheromone has been demonstrated to support route learning, and the effect of pheromones on route choice have been reported to persist even after the pheromones have been removed. This could be explained in two ways: the pheromone may constrain the ants onto the correct route, thus preventing errors and aiding learning. Alternatively, the pheromones may act as a 'reassurance', signalling that the learner is on the right path and that learning the path is worthwhile. Here, we disentangle pheromone presence from route confinement in order to test these hypotheses, using the ant Lasius niger as a model. Unexpectedly, we did not find any evidence that pheromones support route learning. Indeed, there was no evidence that ants confined to the correct route learned at all. Thus, while we cannot support the 'reassurance' hypothesis, we can rule out the 'confinement' hypothesis. Other findings, such as a reduction in pheromone deposition in the presence of trail pheromones, are remarkably consistent with previous experiments. As previously reported, ants which make errors on their outward journey upregulate pheromone deposition on their return. Surprisingly, ants which would go on to make an error down-regulate pheromone deposition on their outward journey, hinting at a capacity for ants to gauge the quality of their own memories.

  8. A Sun Path Observation System Based on Augment Reality and Mobile Learning

    OpenAIRE

    Tarng, Wernhuar; Ou, Kuo-Liang; Lu, Yun-Chen; Shih, Yi-Syuan; Liou, Hsin-Hun

    2018-01-01

    This study uses the augmented reality technology and sensor functions of GPS, electronic compass, and three-axis accelerometer on mobile devices to develop a Sun path observation system for applications in astronomy education. The orientation and elevation of the Sun can be calculated by the system according to the user’s location and local time to simulate the Sun path. When holding the mobile device toward the sky, the screen will show the virtual Sun at the same position as that of the rea...

  9. Path to Stochastic Stability: Comparative Analysis of Stochastic Learning Dynamics in Games

    KAUST Repository

    Jaleel, Hassan; Shamma, Jeff S.

    2018-01-01

    dynamics: Log-Linear Learning (LLL) and Metropolis Learning (ML). Although both of these dynamics have the same stochastically stable states, LLL and ML correspond to different behavioral models for decision making. Moreover, we demonstrate through

  10. Understanding the Causal Path between Action, Learning, and Solutions: Maximizing the Power of Action Learning to Achieve Great Results

    Science.gov (United States)

    Leonard, H. Skipton

    2015-01-01

    Clients and practitioners alike are often confused about the ultimate purpose of action learning (AL). Because of the title of the method, many believe the primary goal of AL is to generate learning. This article clarifies the relationship between action, learning, and solutions. It also provides historical evidence to support the conclusion that…

  11. Promoting social-emotional learning in Chinese schools: A feasibility study of PATHS implementation in Hong Kong

    Directory of Open Access Journals (Sweden)

    Chi-Ming Kam

    2011-04-01

    Full Text Available This paper describes a pilot study of a reduced version of the PATHS Curriculum, a Usdeveloped evidence-based SEL program, among schools in Hong Kong SAR (China. Three hundred and sixteen 12th grade students in three elementary schools participated in the study. A limited number of first grade PATHS lessons were adapted and translated into Chinese. Twelve teachers learned and adopted these lessons in their teaching. Students in these classrooms learned about different emotions and practiced self-control. The intervention lasted four months. After the intervention, students showed improvement in emotion understanding, emotion regulation and prosocial behavior. No change was observed in the level of children's problem behaviors. Over 65% of the teachers reported a high degree of satisfaction and willingness to adopt the intervention. The effects of the intervention varied among schools, with variations in the level of intervention and principal support, but not in the quality of implementation. Discussion is focused on the factors that could shape the adoption and implementation of SEL programs, especially the role of the difference in school systems between Hong Kong and the United States.

  12. Machine Learning Based Dimensionality Reduction Facilitates Ligand Diffusion Paths Assessment: A Case of Cytochrome P450cam.

    Science.gov (United States)

    Rydzewski, J; Nowak, W

    2016-04-12

    In this work we propose an application of a nonlinear dimensionality reduction method to represent the high-dimensional configuration space of the ligand-protein dissociation process in a manner facilitating interpretation. Rugged ligand expulsion paths are mapped into 2-dimensional space. The mapping retains the main structural changes occurring during the dissociation. The topological similarity of the reduced paths may be easily studied using the Fréchet distances, and we show that this measure facilitates machine learning classification of the diffusion pathways. Further, low-dimensional configuration space allows for identification of residues active in transport during the ligand diffusion from a protein. The utility of this approach is illustrated by examination of the configuration space of cytochrome P450cam involved in expulsing camphor by means of enhanced all-atom molecular dynamics simulations. The expulsion trajectories are sampled and constructed on-the-fly during molecular dynamics simulations using the recently developed memetic algorithms [ Rydzewski, J.; Nowak, W. J. Chem. Phys. 2015 , 143 ( 12 ), 124101 ]. We show that the memetic algorithms are effective for enforcing the ligand diffusion and cavity exploration in the P450cam-camphor complex. Furthermore, we demonstrate that machine learning techniques are helpful in inspecting ligand diffusion landscapes and provide useful tools to examine structural changes accompanying rare events.

  13. The role of teachers’ classroom discipline in their teaching effectiveness and students’ language learning motivation and achievement: A path method

    Directory of Open Access Journals (Sweden)

    Mehrak Rahimi

    2015-01-01

    Full Text Available This study investigated the role of EFL teachers’ classroom discipline strategies in their teaching effectiveness and their students’ motivation and achievement in learning English as a foreign language. 1408 junior high-school students expressed their perceptions of the strategies their English teachers used (punishment, recognition/reward, discussion, involvement, and aggression to discipline the classroom. The students evaluated their teachers’ teaching effectiveness by completing effective Iranian EFL teacher questionnaire (Moafian, & Pishghadam, 2009. They also filled in Attitude/Motivation Test Battery (GhorbanDordinejad & ImamJomeh, 2011 that assessed their motivation towards learning English as a foreign language. Achievement in English was established based on formal grades students received at the end of the academic year. The results showed that EFL teachers reward and praise students for good behavior and they are not very authoritarian. Further, teaching effectiveness, motivation and achievement in learning English were all found to be related to discipline strategies. The results of path analysis showed that those teachers who used involvement and recognition strategies more frequently were perceived to be more effective teachers; however, students perceived teachers who used punitive strategies as being less effective in their teaching. It was also revealed that in classes where teachers managed disruptive behaviors by using punitive strategies, students had problems in learning as punitive strategies lowered students’ motivation. Teaching effectiveness was found to mediate the effect of punishment on motivation while motivation mediated the effect of punitive strategies on achievement. Motivation was found to have the strongest effect on achievement.

  14. A fast track path improves access to palliative care for people with learning disabilities.

    Science.gov (United States)

    Whitington, Jane; Ma, Peng

    People with learning disabilities often experience inequalities in accessing general health services. This group, their families and carers need access to effective palliative care when facing a life limiting illness. This article describes the development and implementation of a fast track referral pathway for people with learning disabilities at St Francis Hospice in Essex. Our aim is to share this pathway so others can replicate the collaborative working to improve access to palliative care services for this group.

  15. Constrained paths based on the Farey sequence in learning to juggle.

    Science.gov (United States)

    Yamamoto, Kota; Tsutsui, Seijiro; Yamamoto, Yuji

    2015-12-01

    In this article we report the results of a study conducted to investigate the learning dynamics of three-ball juggling from the perspective of frequency locking. Based on the Farey sequence, we predicted that four stable coordination patterns, corresponding to dwell ratios of 0.83, 0.75, 0.67, and 0.50, would appear in the learning process. We examined the learning process in terms of task performance, taking into account individual differences in the amount of learning. We observed that the participants acquired individual-specific coordination patterns in a relatively early stage of learning, and that those coordination patterns were preserved in subsequent learning, even though performance in terms of number of successful consecutive throws increased substantially. This increase appeared to be related to a reduction in spatial variability of the juggling movements. Finally, the observed coordination patterns were in agreement with the predicted patterns, with the proviso that the pattern corresponding to a dwell ratio of 0.50 was not realized and only a hint of evidence was found for the dwell ratio of 0.67. This implies that the dwell ratios of 0.83 and 0.75 in particular exhibited a stable coordination structure due to strong frequency locking between the temporal variables of juggling. Copyright © 2015 Elsevier B.V. All rights reserved.

  16. Community Learning Campus: The Hard Work Begins after the Ribbon-Cutting

    Science.gov (United States)

    Education Canada, 2012

    2012-01-01

    Dorothy Negropontes was a key player in the creation of the Community Learning Campus (CLC), an innovative collaboration of education and community leaders in Olds, Alberta. A former Assistant Superintendent with Chinook's Edge School District, she co-chaired the steering committee that developed the project, served as its executive director…

  17. Accreditation of prior learning: andragogy in action or a 'cut price' approach to education?

    Science.gov (United States)

    Howard, S

    1993-11-01

    The rapid changes in nurse education are proceeding within the wider context of developments in adjacent educational fields, which are themselves subject to external influences, and one such development is the accreditation of prior experiential learning (APEL). In order to be critically aware of the potential involved in embracing this concept, it is necessary to clarify and examine the influencing factors which guide the current andragogical climate of nurse education, and those which predispose to the recognition of APEL. Utilizing a case-study approach, this paper will examine the relevant issues as they relate to experienced students pursuing the learning outcomes of Project 2000, and will address the question of value for all parties concerned.

  18. The Perfect Mix: With Blended Professional Learning, Learners Choose Time, Place, Path, and Pace

    Science.gov (United States)

    Cieminski, Amie; Andrews, Deagan

    2018-01-01

    The Greeley-Evans School District in Colorado began moving toward innovation several years ago as district leaders searched for ways to improve student achievement, leverage technology, and stay within a very limited budget. In 2014, district leaders created a five-year blended learning implementation plan to increase student achievement that…

  19. United We Learn: Team Effort Builds a Path to Equity and Alignment

    Science.gov (United States)

    Kind, Jill

    2014-01-01

    This article presents a plan to create a united approach to improve high quality instruction in Robbinsdale Cooper High School in New Hope, Minnesota, a suburb of Minneapolis. Professional learning communities were in their infancy, conversations around data were about autopsies of annual standardized tests, and there was no description of what…

  20. Learning a Foreign Language: A New Path to Enhancement of Cognitive Functions

    Science.gov (United States)

    Shoghi Javan, Sara; Ghonsooly, Behzad

    2018-01-01

    The complicated cognitive processes involved in natural (primary) bilingualism lead to significant cognitive development. Executive functions as a fundamental component of human cognition are deemed to be affected by language learning. To date, a large number of studies have investigated how natural (primary) bilingualism influences executive…

  1. Math Path: Encouraging Female Students in Mathematics through Project-Based Learning

    Science.gov (United States)

    Evans, Riley; Friedman, Jane; McGrath, Lynn; Myers, Perla; Ruiz, Amanda

    2018-01-01

    Although the number of bachelor's degrees in the U.S. awarded to women has gone up, engagement of women in science, technology, engineering, and mathematics (STEM) continues to be low. This paper presents a project-based learning program, informed by education research best practices, designed to provide research experiences to female students…

  2. From Places to Paths: "Learning for Sustainability," Teacher Education and a Philosophy of Becoming

    Science.gov (United States)

    Clarke, David A. G.; Mcphie, Jamie

    2016-01-01

    The purpose of this paper is to explore what thinking with a philosophy of "becoming" might produce in terms of conceptualising "Learning for Sustainability" ("LfS"), a recent development in Scottish educational policy. The paper posits that animism and the immanent materiality of a philosophy of becoming have…

  3. Power learning or path dependency? Investigating the roots of the European Food Safety Authority.

    Science.gov (United States)

    Roederer-Rynning, Christilla; Daugbjerg, Carsten

    2010-01-01

    A key motive for establishing the European Food Safety Authority (EFSA) was restoring public confidence in the wake of multiplying food scares and the BSE crisis. Scholars, however, have paid little attention to the actual political and institutional logics that shaped this new organization. This article explores the dynamics underpinning the making of EFSA. We examine the way in which learning and power shaped its organizational architecture. It is demonstrated that the lessons drawn from the past and other models converged on the need to delegate authority to an external agency, but diverged on its mandate, concretely whether or not EFSA should assume risk management responsibilities. In this situation of competitive learning, power and procedural politics conditioned the mandate granted to EFSA. The European Commission, the European Parliament and the European Council shared a common interest in preventing the delegation of regulatory powers to an independent EU agency in food safety policy.

  4. PATHS in Croatia: A school-based randomised-controlled trial of a social and emotional learning curriculum.

    Science.gov (United States)

    Novak, Miranda; Mihić, Josipa; Bašić, Josipa; Nix, Robert L

    2017-04-01

    This study represents the first rigorous evaluation of a social-emotional learning curriculum, PATHS (Promoting Alternative Thinking Strategies; Kusché & Greenberg, 1994), in elementary schools in Croatia. This study randomly assigned 29 schools to receive the universal preventive intervention or continue with usual practices. Within those schools, this study included 57 classrooms and 568 children. Teachers rated nine child behaviours in the middle of first grade (pre-intervention) and near the end of second grade (post-intervention). Hierarchical linear models, nesting children within classrooms, revealed few changes in behaviour across the sample as a whole or among higher risk children. However, there were changes on eight of the nine behaviours for lower risk children. The findings are considered in the context of the classroom culture and teachers' preparation and readiness to implement a social-emotional learning curriculum in Croatia. This study highlights the need to supplement universal preventive interventions with selective preventive interventions that can provide more intensive and targeted skill practice for higher risk children. This study also highlights the nuanced effects of a universal preventive intervention in helping different children in different ways. © 2016 International Union of Psychological Science.

  5. The Perceptions of Temporal Path Analysis of Learners' Self-Regulation on Learning Stress and Social Relationships in Junior High School

    Science.gov (United States)

    Chang, Hsiu-Ju

    2016-01-01

    This research focus on the temporal path analysis of learning stress, test anxiety, peer stress (classmate relatedness), teacher relatedness, autonomy, and self-regulative performance in junior high school. Owing to the processes of self-determination always combines several negotiations with the interactive perceptions of personal experiences and…

  6. Path Dependency

    OpenAIRE

    Mark Setterfield

    2015-01-01

    Path dependency is defined, and three different specific concepts of path dependency – cumulative causation, lock in, and hysteresis – are analyzed. The relationships between path dependency and equilibrium, and path dependency and fundamental uncertainty are also discussed. Finally, a typology of dynamical systems is developed to clarify these relationships.

  7. Structured feedback on students' concept maps: the proverbial path to learning?

    Science.gov (United States)

    Joseph, Conran; Conradsson, David; Nilsson Wikmar, Lena; Rowe, Michael

    2017-05-25

    Good conceptual knowledge is an essential requirement for health professions students, in that they are required to apply concepts learned in the classroom to a variety of different contexts. However, the use of traditional methods of assessment limits the educator's ability to correct students' conceptual knowledge prior to altering the educational context. Concept mapping (CM) is an educational tool for evaluating conceptual knowledge, but little is known about its use in facilitating the development of richer knowledge frameworks. In addition, structured feedback has the potential to develop good conceptual knowledge. The purpose of this study was to use Kinchin's criteria to assess the impact of structured feedback on the graphical complexity of CM's by observing the development of richer knowledge frameworks. Fifty-eight physiotherapy students created CM's targeting the integration of two knowledge domains within a case-based teaching paradigm. Each student received one round of structured feedback that addressed correction, reinforcement, forensic diagnosis, benchmarking, and longitudinal development on their CM's prior to the final submission. The concept maps were categorized according to Kinchin's criteria as either Spoke, Chain or Net representations, and then evaluated against defined traits of meaningful learning. The inter-rater reliability of categorizing CM's was good. Pre-feedback CM's were predominantly Chain structures (57%), with Net structures appearing least often. There was a significant reduction of the basic Spoke- structured CMs (P = 0.002) and a significant increase of Net-structured maps (P student development.

  8. Learning a Foreign Language: A New Path to Enhancement of Cognitive Functions.

    Science.gov (United States)

    Shoghi Javan, Sara; Ghonsooly, Behzad

    2018-02-01

    The complicated cognitive processes involved in natural (primary) bilingualism lead to significant cognitive development. Executive functions as a fundamental component of human cognition are deemed to be affected by language learning. To date, a large number of studies have investigated how natural (primary) bilingualism influences executive functions; however, the way acquired (secondary) bilingualism manipulates executive functions is poorly understood. To fill this gap, controlling for age, gender, IQ, and socio-economic status, the researchers compared 60 advanced learners of English as a foreign language (EFL) to 60 beginners on measures of executive functions involving Stroop, Wisconsin Card Sorting Task (WCST) and Wechsler's digit span tasks. The results suggested that mastering English as a foreign language causes considerable enhancement in two components of executive functions, namely cognitive flexibility and working memory. However, no significant difference was observed in inhibitory control between the advanced EFL learners and beginners.

  9. Reachability cuts for the vehicle routing problem with time windows

    DEFF Research Database (Denmark)

    Lysgaard, Jens

    2004-01-01

    This paper introduces a class of cuts, called reachability cuts, for the Vehicle Routing Problem with Time Windows (VRPTW). Reachability cuts are closely related to cuts derived from precedence constraints in the Asymmetric Traveling Salesman Problem with Time Windows and to k-path cuts...

  10. The Ocean Observatories Initiative Data Management and QA/QC: Lessons Learned and the Path Ahead

    Science.gov (United States)

    Vardaro, M.; Belabbassi, L.; Garzio, L. M.; Knuth, F.; Smith, M. J.; Kerfoot, J.; Crowley, M. F.

    2016-02-01

    The Ocean Observatories Initiative (OOI) is a multi-decadal, NSF-funded program that will provide long-term, near real-time cabled and telemetered measurements of climate variability, ocean circulation, ecosystem dynamics, air-sea exchange, seafloor processes, and plate-scale geodynamics. The OOI platforms consist of seafloor sensors, fixed moorings, and mobile assets containing over 700 operational instruments in the Atlantic and Pacific oceans. Rutgers University operates the Cyberinfrastructure (CI) component of the OOI, which acquires, processes and distributes data to scientists, researchers, educators and the public. It will also provide observatory mission command and control, data assessment and distribution, and long-term data management. The Rutgers Data Management Team consists of a data manager and four data evaluators, who are tasked with ensuring data completeness and quality, as well as interaction with OOI users to facilitate data delivery and utility. Here we will discuss the procedures developed to guide the data team workflow, the automated QC algorithms and human-in-the-loop (HITL) annotations that are used to flag suspect data (whether due to instrument failures, biofouling, or unanticipated events), system alerts and alarms, long-term data storage and CF (Climate and Forecast) standard compliance, and the lessons learned during construction and the first several months of OOI operations.

  11. Thinking Like a Scientist: The RITES Path for K-12 Students to Learn the Scientific Method

    Science.gov (United States)

    Murray, D. P.; Dooley, H., Jr.; Cardace, D.

    2015-12-01

    Bringing Research on Learning to the Geosciences (Manduca et al, 2002) stated that "An overaching goal for geoscience education is to help every student to 'think like a scientist'", and that continues to challenge geoscience education. The Rhode Island Technology Enhanced Science (RITES) project addresses that goal, and this presentation chronicles that successful effort. RITES strives to improve science education by providing professional development (PD) to the majority of science teachers at the 5th through 12th grade levels throughout Rhode Island. The PD is presented through ~forty 2.5 day workshops that emphasize the innovative use of technology and best teaching practices, consistent with the recommendations detailed in Manduca et al (2002). The presentation will focus on two of these workshops that provide middle and high school teachers with strategies and techniques for guiding student-run explorations of earthquakes as a result of tectonic plate movements. Teachers address these topics much as a scientist would by carrying out the following activities: 1) Identifying the relationships between faults, EQs and plate boundaries; 2) Using GPS data to quantify interseismic deformation; 3) Constructing an Earthquake machine; and 4) Scaling their observations from desktop to crustal scale, and (5) Using the results to forecast earthquakes along the SAF and to estimate the magnitude of earthquakes on ancient faults. As it is unrealistic to expect teachers to be able to incorporate all of this material into their syllabi, we have introduced the concept of Subtle Shifts (Exploratorium, 2006) as a means by which they can easily blend workshop material into their existing courses. Teacher surveys reflect a high level of satisfaction (81-100%), and pre- and post-evaluations show significant normalized gains (Hake, 1998), in about 90% of the courses. Moreover, students of RITES teachers demonstrate statistically significant gains in inquiry skills and content

  12. Análise de trilha em caracteres produtivos de Pennisetum sob corte em Itambé, Pernambuco Path analysis in productive characters of Pennisetum under cut in Itambé-PE

    Directory of Open Access Journals (Sweden)

    Mônica Alixandrina da Silva

    2008-07-01

    Full Text Available Objetivou-se obter estimativas de coeficientes de correlação genética e avaliar os desdobramentos das correlações em efeitos diretos e indiretos (análise de trilha das variáveis independentes explicativas sobre a produção de matéria seca (variável dependente principal em cinco clones de capim-elefante. Foram realizados cinco cortes a cada 60 dias nas condições edafoclimáticas da Zona da Mata de Pernambuco. Cada parcela experimental apresentou 24 m², com 2 m² de área útil. Houve alta correlação entre quase todas as variáveis explicativas e a variável principal. Entretanto, a característica número de lâminas foliares por perfilho explicou melhor o potencial de produção de matéria seca e atuou de forma direta e indireta sobre as variáveis explicativas.This work aimed to estimate the correlation coefficients, determining the direct and indirect effects (path analysis of explanatory independent variables on total dry matter production (main dependent variables of five elephant grass clones in five cuts accomplished at the forest zone of Pernambuco. Each experimental plot measured 24 m² with 2 m² of utile area. There was high correlation between almost all the independent variables and the main variable. The characteristic leaf blade number per tiller, however, explained better the potential of dry matter production and leaf blade dry matter production, acting, respectively, in a direct and indirect way on the explanatory variables.

  13. Navigating the Path of Totality - Results and Lessons Learned from the 2017 Eclipse Broadcast, Webcast, Mobile App and Online Production

    Science.gov (United States)

    Semper, R.; Higdon, R.

    2017-12-01

    The 2017 total solar eclipse provided unique opportunity to provide public outreach about astronomy, heliophysics, and scientific discovery. The Navigating the Path of Totality project was designed to produce eclipse related educational resources including live video feeds and distribute them to museums, schools, libraries and the public through online and broadcast media. Using special telescope video camera setups, five feeds were produced including a live one hour English program and in parallel a live one hour Spanish program from Casper, WY with a cutaway to Madras, OR, complete (C1-C4) telescope only feeds from both Madras, OR and Casper, Wy, and a complete (C1-C4) telescope only feed with live musical sonification and accompaniment by the Kronos Quartet. Images from the live feeds were made available on the NASA Website, NASA TV, Exploratorium website, Exploratorium Solar Eclipse mobile app, local television and in museums, libraries and schools worldwide. Associated educational video material including images from the 2016 total eclipse from Micronesia was produced and disseminated. In this talk we will discuss the evaluation results including an examination of the effectiveness of the digital strategy of many mobile channels and mobile apps using different analytics including IBM Watson social media analytics services. We will also present the lessons learned from the project.

  14. Cutting cleaner

    International Nuclear Information System (INIS)

    Elsen, R.P.H. van; Smits, M.

    1991-01-01

    This paper presents the results of a long term field test of the Cutting Cleaner, which is used for the treatment of wet oil contaminated cuttings (WOCC) produced when drilling with Oil Based Mud (OBM). It was concluded that it is possible to reduce the oil content of cuttings to an average of 1 - 2%. The recovered base oil can be reused to make new oil based mud

  15. Changes in Search Path Complexity and Length During Learning of a Virtual Water Maze: Age Differences and Differential Associations with Hippocampal Subfield Volumes.

    Science.gov (United States)

    Daugherty, Ana M; Bender, Andrew R; Yuan, Peng; Raz, Naftali

    2016-06-01

    Impairment of hippocampus-dependent cognitive processes has been proposed to underlie age-related deficits in navigation. Animal studies suggest a differential role of hippocampal subfields in various aspects of navigation, but that hypothesis has not been tested in humans. In this study, we examined the association between volume of hippocampal subfields and age differences in virtual spatial navigation. In a sample of 65 healthy adults (age 19-75 years), advanced age was associated with a slower rate of improvement operationalized as shortening of the search path over 25 learning trials on a virtual Morris water maze task. The deficits were partially explained by greater complexity of older adults' search paths. Larger subiculum and entorhinal cortex volumes were associated with a faster decrease in search path complexity, which in turn explained faster shortening of search distance. Larger Cornu Ammonis (CA)1-2 volume was associated with faster distance shortening, but not in path complexity reduction. Age differences in regional volumes collectively accounted for 23% of the age-related variance in navigation learning. Independent of subfield volumes, advanced age was associated with poorer performance across all trials, even after reaching the asymptote. Thus, subiculum and CA1-2 volumes were associated with speed of acquisition, but not magnitude of gains in virtual maze navigation. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

  16. Paper Cuts.

    Science.gov (United States)

    Greene, Lisa A.

    1990-01-01

    Describes how to create paper cuts and suggests the most appropriate materials for young children that give good quality results. Describes the methods the author, a professional artist, uses to assemble her own paper cuts and how these can be adopted by older students. (KM)

  17. Path Expressions

    Science.gov (United States)

    1975-06-01

    Traditionally, synchronization of concurrent processes is coded in line by operations on semaphores or similar objects. Path expressions move the...discussion about a variety of synchronization primitives . An analysis of their relative power is found in [3]. Path expressions do not introduce yet...another synchronization primitive . A path expression relates to such primitives as a for- or while-statement of an ALGOL-like language relates to a JUMP

  18. Wet cutting

    Energy Technology Data Exchange (ETDEWEB)

    Hole, B. [IMC Technical Services (United Kingdom)

    1999-08-01

    Continuous miners create dust and methane problems in underground coal mining. Control has usually been achieved using ventilation techniques as experiments with water based suppression have led to flooding and electrical problems. Recent experience in the US has led to renewed interest in wet head systems. This paper describes tests of the Hydraphase system by IMC Technologies. Ventilation around the cutting zone, quenching of hot ignition sources, dust suppression, the surface trial gallery tests, the performance of the cutting bed, and flow of air and methane around the cutting head are reviewed. 1 ref., 2 figs., 2 photos.

  19. Cutting assembly

    Science.gov (United States)

    Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

    1984-01-01

    A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

  20. Designing and Developing a Novel Hybrid Adaptive Learning Path Recommendation System (ALPRS) for Gamification Mathematics Geometry Course

    Science.gov (United States)

    Su, Chung-Ho

    2017-01-01

    Since recommendation systems possess the advantage of adaptive recommendation, they have gradually been applied to e-learning systems to recommend subsequent learning content for learners. However, problems exist in current learning recommender systems available to students in that they are often general learning content and unable to offer…

  1. Using Cooking, Baking, and Cutting Terms. Learning Activity Pack and Instructor's Guide 5.1a. Commercial Foods and Culinary Arts Competency-Based Series. Section 5: Basic Food Preparation.

    Science.gov (United States)

    Florida State Univ., Tallahassee. Center for Studies in Vocational Education.

    This document consists of a learning activity packet (LAP) for the student and an instructor's guide for the teacher. The LAP is intended to acquaint occupational home economics students with some of the terms used in recipes. Illustrated information sheets and learning activities are provided on important cooking, baking, and cutting terms. The…

  2. Cutting Cosmos

    DEFF Research Database (Denmark)

    Mikkelsen, Henrik Hvenegaard

    For the first time in over 30 years, a new ethnographic study emerges on the Bugkalot tribe, more widely known as the Ilongot of the northern Philippines. Exploring the notion of masculinity among the Bugkalot, Cutting Cosmos is not only an experimental, anthropological study of the paradoxes...... around which Bugkalot society revolves, but also a reflection on anthropological theory and writing. Focusing on the transgressive acts through which masculinity is performed, this book explores the idea of the cosmic cut, the ritual act that enables the Bugkalot man to momentarily hold still the chaotic...

  3. Research on NC laser combined cutting optimization model of sheet metal parts

    Science.gov (United States)

    Wu, Z. Y.; Zhang, Y. L.; Li, L.; Wu, L. H.; Liu, N. B.

    2017-09-01

    The optimization problem for NC laser combined cutting of sheet metal parts was taken as the research object in this paper. The problem included two contents: combined packing optimization and combined cutting path optimization. In the problem of combined packing optimization, the method of “genetic algorithm + gravity center NFP + geometric transformation” was used to optimize the packing of sheet metal parts. In the problem of combined cutting path optimization, the mathematical model of cutting path optimization was established based on the parts cutting constraint rules of internal contour priority and cross cutting. The model played an important role in the optimization calculation of NC laser combined cutting.

  4. Path Dependence

    DEFF Research Database (Denmark)

    Madsen, Mogens Ove

    Begrebet Path Dependence blev oprindelig udviklet inden for New Institutionel Economics af bl.a. David, Arthur og North. Begrebet har spredt sig vidt i samfundsvidenskaberne og undergået en udvikling. Dette paper propagerer for at der er sket så en så omfattende udvikling af begrebet, at man nu kan...... tale om 1. og 2. generation af Path Dependence begrebet. Den nyeste udvikling af begrebet har relevans for metodologi-diskusionerne i relation til Keynes...

  5. Cutting Itch

    OpenAIRE

    Zellweger, Christoph

    2015-01-01

    Cutting Itch” is a curatorial project by artists-duo Baltensperger-Siepert. An exhibition project about the essential need of art to be an active system that reflects, investigates social, cultural and political issues. It is about an existential necessity to shape ones environment, to think about relations, regulating structures and about how we can locate ourselves in a more and more globalised world. (from press material). \\ud \\ud Baltensperger & Siepert identified seven artists from Mexi...

  6. Paper-cutting operations using scissors in Drury's law tasks.

    Science.gov (United States)

    Yamanaka, Shota; Miyashita, Homei

    2018-05-01

    Human performance modeling is a core topic in ergonomics. In addition to deriving models, it is important to verify the kinds of tasks that can be modeled. Drury's law is promising for path tracking tasks such as navigating a path with pens or driving a car. We conducted an experiment based on the observation that paper-cutting tasks using scissors resemble such tasks. The results showed that cutting arc-like paths (1/4 of a circle) showed an excellent fit with Drury's law (R 2  > 0.98), whereas cutting linear paths showed a worse fit (R 2  > 0.87). Since linear paths yielded better fits when path amplitudes were divided (R 2  > 0.99 for all amplitudes), we discuss the characteristics of paper-cutting operations using scissors. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. The Influence of E-learning Characteristics and Basic Ict Competencies to Actual USAge of E-learning: a Path Diagram Model

    OpenAIRE

    Suarta, I Made; Suwintana, I Ketut

    2015-01-01

    In this paper, the Technology Acceptance Model (TAM) is extent with two external stimulus namely e-learning characteristics and basic ICT (Information and Communication Technology) competencies. The purpose of this study are (1) finding relationship between e-learning characteristics and lecturers' basic ICT competencies with the perceived ease of use and perceived usefulness of e-learning; and (2) determining the effect of e-learning characteristics and lecturer basic ICT competencies to the...

  8. Engineering the path to higher-order thinking in elementary education: A problem-based learning approach for STEM integration

    Science.gov (United States)

    Rehmat, Abeera Parvaiz

    As we progress into the 21st century, higher-order thinking skills and achievement in science and math are essential to meet the educational requirement of STEM careers. Educators need to think of innovative ways to engage and prepare students for current and future challenges while cultivating an interest among students in STEM disciplines. An instructional pedagogy that can capture students' attention, support interdisciplinary STEM practices, and foster higher-order thinking skills is problem-based learning. Problem-based learning embedded in the social constructivist view of teaching and learning (Savery & Duffy, 1995) promotes self-regulated learning that is enhanced through exploration, cooperative social activity, and discourse (Fosnot, 1996). This quasi-experimental mixed methods study was conducted with 98 fourth grade students. The study utilized STEM content assessments, a standardized critical thinking test, STEM attitude survey, PBL questionnaire, and field notes from classroom observations to investigate the impact of problem-based learning on students' content knowledge, critical thinking, and their attitude towards STEM. Subsequently, it explored students' experiences of STEM integration in a PBL environment. The quantitative results revealed a significant difference between groups in regards to their content knowledge, critical thinking skills, and STEM attitude. From the qualitative results, three themes emerged: learning approaches, increased interaction, and design and engineering implementation. From the overall data set, students described the PBL environment to be highly interactive that prompted them to employ multiple approaches, including design and engineering to solve the problem.

  9. Exploring the Visuospatial Challenge of Learning about Day and Night and the Sun's Path

    Science.gov (United States)

    Heywood, David; Parker, Joan; Rowlands, Mark

    2013-01-01

    The role of visualization and model-based reasoning has become increasingly significant in science education across a range of contexts. It is generally recognized that supporting learning in developing causal explanations for observed astronomical events presents considerable pedagogic challenge. Understanding the Sun's apparent movement…

  10. Path Analysis on the Factors Influencing Learning Outcome for Hospitality Interns--From the Flow Theory Perspective

    Science.gov (United States)

    Wang, Shu-Tai; Chen, Cheng-Chung

    2015-01-01

    Learning outcome is an important indicator for educators in evaluating curriculum design. The focus of this study has been to examine the factors within internship programs, recognizing the complex nature of knowledge application in a practical industry environment. Flow theory was adopted to explain the psychological state of hospitality students…

  11. The Role of Teachers' Classroom Discipline in Their Teaching Effectiveness and Students' Language Learning Motivation and Achievement: A Path Method

    Science.gov (United States)

    Rahimi, Mehrak; Karkami, Fatemeh Hosseini

    2015-01-01

    This study investigated the role of EFL teachers' classroom discipline strategies in their teaching effectiveness and their students' motivation and achievement in learning English as a foreign language. 1408 junior high-school students expressed their perceptions of the strategies their English teachers used (punishment, recognition/reward,…

  12. Analysis of the learning curve for pre-cut corneal specimens in preparation for lamellar transplantation: a prospective, single-centre, consecutive case series prepared at the Lions New South Wales Eye Bank.

    Science.gov (United States)

    Martin, Aifric Isabel; Devasahayam, Rajnesh; Hodge, Christopher; Cooper, Simon; Sutton, Gerard L

    2017-09-01

    This study is the first paper to establish a learning curve by a single technician. Preparation of pre-cut corneal endothelial grafts commenced at Lions New South Wales Eye Bank in December 2014. The primary objective of this study was to review the safety and reliability of the preparation method during the first year of production. This is a hospital-based, prospective case series. There were 234 consecutive donor corneal lenticules. Donor lenticules were prepared by a single operator using a linear cutting microkeratome. Immediately prior to cutting, central corneal thickness values were recorded. Measurements of the corneal bed were taken immediately following lenticule preparation. Outcomes were separated by blade sizes, and intended thickness was compared to actual thickness for each setting. Early specimens were compared to later ones to assess for a learning curve within the technique. The main parameter measured is the mean difference from intended lamellar cut thickness. The mean final cut thickness was 122.36 ± 20.35 μm, and the mean difference from intended cut was 30.17 ± 37.45 μm. No significant difference was found between results achieved with early specimens versus those achieved with later specimens (P = 0.425). Thin, reproducible endothelial grafts can routinely be produced by trained technicians at their respective eye banks without significant concerns for an extended learning curve. This service can reduce perioperative surgical complexity, required surgical paraphernalia and theatre times. The consistent preparation of single-pass, ultrathin pre-cut corneas may have additional advantages for surgeons seeking to introduce lamellar techniques. © 2017 Royal Australian and New Zealand College of Ophthalmologists.

  13. Hemoglobin-Based Oxygen Carrier (HBOC) Development in Trauma: Previous Regulatory Challenges, Lessons Learned, and a Path Forward.

    Science.gov (United States)

    Keipert, Peter E

    2017-01-01

    Historically, hemoglobin-based oxygen carriers (HBOCs) were being developed as "blood substitutes," despite their transient circulatory half-life (~ 24 h) vs. transfused red blood cells (RBCs). More recently, HBOC commercial development focused on "oxygen therapeutic" indications to provide a temporary oxygenation bridge until medical or surgical interventions (including RBC transfusion, if required) can be initiated. This included the early trauma trials with HemAssist ® (BAXTER), Hemopure ® (BIOPURE) and PolyHeme ® (NORTHFIELD) for resuscitating hypotensive shock. These trials all failed due to safety concerns (e.g., cardiac events, mortality) and certain protocol design limitations. In 2008 the Food and Drug Administration (FDA) put all HBOC trials in the US on clinical hold due to the unfavorable benefit:risk profile demonstrated by various HBOCs in different clinical studies in a meta-analysis published by Natanson et al. (2008). During standard resuscitation in trauma, organ dysfunction and failure can occur due to ischemia in critical tissues, which can be detected by the degree of lactic acidosis. SANGART'S Phase 2 trauma program with MP4OX therefore added lactate >5 mmol/L as an inclusion criterion to enroll patients who had lost sufficient blood to cause a tissue oxygen debt. This was key to the successful conduct of their Phase 2 program (ex-US, from 2009 to 2012) to evaluate MP4OX as an adjunct to standard fluid resuscitation and transfusion of RBCs. In 2013, SANGART shared their Phase 2b results with the FDA, and succeeded in getting the FDA to agree that a planned Phase 2c higher dose comparison study of MP4OX in trauma could include clinical sites in the US. Unfortunately, SANGART failed to secure new funding and was forced to terminate development and operations in Dec 2013, even though a regulatory path forward with FDA approval to proceed in trauma had been achieved.

  14. Whatever It Takes A Case Study Of Our Childs Alternative Path To Literacy

    Directory of Open Access Journals (Sweden)

    Shelly HUGGINS

    2016-12-01

    Full Text Available As public school educators, my husband and I struggled with making alternative academic choices for our child with learning differences. Choosing the alternative path was not easy or clear cut for us. This is a reflective record of the journey toward getting my son Whatever it Takes to help him learn. The article chronicles intuition about the early warning signs of learning differences. The article discusses the merits of the private school experience, the homeschooling experience and ultimately a modified and personalized learning plan that made learning natural, while preserving my sons confidence, self-esteem and integrity. Detailed in the article are the discussions concerning the many educational, instructional and sociological decisions that are necessary to individualize instruction to meet an individuals needs.

  15. A Case Study on the Implementation of a Positive Youth Development Program (Project P.A.T.H.S. in Hong Kong: Learning from the Experimental Implementation Phase

    Directory of Open Access Journals (Sweden)

    Tak Yan Lee

    2008-01-01

    Full Text Available This investigation of the implementation of a positive youth development program (Project P.A.T.H.S. was part of a large study undertaken comprehensively to explore how effective the Tier 1 Program was in practice and how the results can shed light on future developments. Utilizing a case study approach, individual and focus group interviews were conducted in 2007 to examine the factors that influence the process and quality of implementation of the Tier 1 Program of the Project P.A.T.H.S. The focus of this study was on how the implementers of a school made use of the experience gained in the Experimental Implementation Phase (EIP in 2005/06 to improve the program implementation quality in the Full Implementation Phase (FIP in 2006/07. Results showed that the program implementation in the FIP was generally high and the program was well received by the implementers. Factors that facilitated the implementation of the program were identified, including the adoption of an incremental change strategy, the incorporation of the program into both formal and informal curricula, positive perceptions of the program among staff and agency social workers, sufficient school administrative support, excellent cooperation between the school and the social work agency, presence of a dedicated school contact person and instructors who engaged themselves in continuous quality improvement of the implementation, and an emphasis on application of what had been learned. Difficulties encountered by the school in the process of implementation were also observed. Based on the present findings, key process variables that facilitate or impede the implementation of positive youth development programs are discussed. Implications for future program implementation are also discussed.

  16. Learning Paths and Learning Styles in Dyslexia: Possibilites and Effectiveness--Case Study of Two Elementary School Students Aged 7 Years Old

    Science.gov (United States)

    Tsampalas, Evangelos; Dimitrios, Sarris; Papadimitropoulou, Panagoula; Vergou, Maria; Zakopoulou, Victoria

    2018-01-01

    The difficulty in reading and writing, spelling mistakes and poor speech are considered as the main elements that characterize students with dyslexia. If one thinks that most of the things in a class are based on writing and reading, then the importance of such a learning difficulty is that it is recognized as soon as possible and with appropriate…

  17. Plasma arc cutting: speed and cut quality

    International Nuclear Information System (INIS)

    Nemchinsky, V A; Severance, W S

    2009-01-01

    When cutting metal with plasma arc cutting, the walls of the cut are narrower at the bottom than at the top. This lack of squareness increases as the cutting speed increases. A model of this phenomenon, affecting cut quality, is suggested. A thin liquid layer, which separates the plasma from the solid metal to be melted, plays a key role in the suggested model. This layer decreases heat transfer from the plasma to the solid metal; the decrease is more pronounced the higher the speed and the thicker the liquid metal layer. Since the layer is thicker at the bottom of the cut, the heat transfer effectiveness is lower at the bottom. The decrease in heat transfer effectiveness is compensated by the narrowness of the cut. The suggested model allows one to calculate the profile of the cut. The result of the calculations of the cutting speeds for plates of various thicknesses, at which the squareness of the cut is acceptable, agrees well with the speeds recommended by manufacturers. The second effect considered in the paper is the deflection of the plasma jet from the vertical at a high cutting speed. A qualitative explanation of this phenomenon is given. We believe the considerations of this paper are pertinent to other types of cutting with moving heat sources.

  18. The endocrine-brain-aging triad where many paths meet: female reproductive hormone changes at midlife and their influence on circuits important for learning and memory.

    Science.gov (United States)

    Koebele, Stephanie V; Bimonte-Nelson, Heather A

    2017-08-01

    Female mammals undergo natural fluctuations in sex steroid hormone levels throughout life. These fluctuations span from early development, to cyclic changes associated with the menstrual or estrous cycle and pregnancy, to marked hormone flux during perimenopause, and a final decline at reproductive senescence. While the transition to reproductive senescence is not yet fully understood, the vast majority of mammals experience this spontaneous, natural phenomenon with age, which has broad implications for long-lived species. Indeed, this post-reproductive life stage, and its transition, involves significant and enduring physiological changes, including considerably altered sex steroid hormone and gonadotropin profiles that impact multiple body systems, including the brain. The endocrine-brain-aging triad is especially noteworthy, as many paths meet and interact. Many of the brain regions affected by aging are also sensitive to changes in ovarian hormone levels, and aging and reproductive senescence are both associated with changes in memory performance. This review explores how menopause is related to cognitive aging, and discusses some of the key neural systems and molecular factors altered with age and reproductive hormone level changes, with an emphasis on brain regions important for learning and memory. Copyright © 2017. Published by Elsevier Inc.

  19. Errant paths

    DEFF Research Database (Denmark)

    Pinder, David

    2011-01-01

    Walking has moved into increasing visibility in social, cultural, and geographical studies as well as art and cultural practice in recent times.Walking practices are often mobilised as a means for sensing and learning about spaces, for enabling reflection on the mutual constitution of bodies...... and landscapes, and for finding meaning within and potentially re-enchanting environments. Through the influence of Michel de Certeau in particular, the idea that walking `encunciates' spaces and is a creative, elusive, and resistive everyday practice, counterpoised to the `solar eye', has become commonplace....... This paper focuses on projects by the artist Francis Aly«s that are based on walking in London and other cities, to consider their engagements with the politics of urban space. Attention is paid to walking as his method of unfolding stories, and to its potential to unsettle and bring into question current...

  20. Path Creation, Path Dependence and Breaking Away from the Path

    OpenAIRE

    Wang, Jens; Hedman, Jonas; Tuunainen, Virpi Kristiina

    2016-01-01

    The explanation of how and why firms succeed or fail is a recurrent research challenge. This is particularly important in the context of technological innovations. We focus on the role of historical events and decisions in explaining such success and failure. Using a case study of Nokia, we develop and extend a multi-layer path dependence framework. We identify four layers of path dependence: technical, strategic and leadership, organizational, and external collaboration. We show how path dep...

  1. Multibeam Fibre Laser Cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre......-laser cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single...

  2. Multibeam fiber laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove; Hansen, Klaus Schütt; Nielsen, Jakob Skov

    2009-01-01

    The appearance of the high power high brilliance fiber laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating Cutting laser, the CO2 laser. However, quality problems in fiber......-laser cutting have until now limited its application to metal cutting. In this paper the first results of proof-of-principle Studies applying a new approach (patent pending) for laser cutting with high brightness and short wavelength lasers will be presented. In the approach, multibeam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from two single mode fiber lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W...

  3. Cutting state identification

    International Nuclear Information System (INIS)

    Berger, B.S.; Minis, I.; Rokni, M.

    1997-01-01

    Cutting states associated with the orthogonal cutting of stiff cylinders are identified through an analysis of the singular values of a Toeplitz matrix of third order cumulants of acceleration measurements. The ratio of the two pairs of largest singular values is shown to differentiate between light cutting, medium cutting, pre-chatter and chatter states. Sequences of cutting experiments were performed in which either depth of cut or turning frequency was varied. Two sequences of experiments with variable turning frequency and five with variable depth of cut, 42 cutting experiments in all, provided a database for the calculation of third order cumulants. Ratios of singular values of cumulant matrices find application in the analysis of control of orthogonal cutting

  4. Flexible Laser Metal Cutting

    DEFF Research Database (Denmark)

    Villumsen, Sigurd; Jørgensen, Steffen Nordahl; Kristiansen, Morten

    2014-01-01

    This paper describes a new flexible and fast approach to laser cutting called ROBOCUT. Combined with CAD/CAM technology, laser cutting of metal provides the flexibility to perform one-of-a-kind cutting and hereby realises mass production of customised products. Today’s laser cutting techniques...... possess, despite their wide use in industry, limitations regarding speed and geometry. Research trends point towards remote laser cutting techniques which can improve speed and geometrical freedom and hereby the competitiveness of laser cutting compared to fixed-tool-based cutting technology...... such as punching. This paper presents the concepts and preliminary test results of the ROBOCUT laser cutting technology, a technology which potentially can revolutionise laser cutting....

  5. Feynman's path integrals and Bohm's particle paths

    International Nuclear Information System (INIS)

    Tumulka, Roderich

    2005-01-01

    Both Bohmian mechanics, a version of quantum mechanics with trajectories, and Feynman's path integral formalism have something to do with particle paths in space and time. The question thus arises how the two ideas relate to each other. In short, the answer is, path integrals provide a re-formulation of Schroedinger's equation, which is half of the defining equations of Bohmian mechanics. I try to give a clear and concise description of the various aspects of the situation. (letters and comments)

  6. Path coupling and aggregate path coupling

    CERN Document Server

    Kovchegov, Yevgeniy

    2018-01-01

    This book describes and characterizes an extension to the classical path coupling method applied to statistical mechanical models, referred to as aggregate path coupling. In conjunction with large deviations estimates, the aggregate path coupling method is used to prove rapid mixing of Glauber dynamics for a large class of statistical mechanical models, including models that exhibit discontinuous phase transitions which have traditionally been more difficult to analyze rigorously. The book shows how the parameter regions for rapid mixing for several classes of statistical mechanical models are derived using the aggregate path coupling method.

  7. High repetition rate ultrashort laser cuts a path through fog

    Science.gov (United States)

    de la Cruz, Lorena; Schubert, Elise; Mongin, Denis; Klingebiel, Sandro; Schultze, Marcel; Metzger, Thomas; Michel, Knut; Kasparian, Jérôme; Wolf, Jean-Pierre

    2016-12-01

    We experimentally demonstrate that the transmission of a 1030 nm, 1.3 ps laser beam of 100 mJ energy through fog increases when its repetition rate increases to the kHz range. Due to the efficient energy deposition by the laser filaments in the air, a shockwave ejects the fog droplets from a substantial volume of the beam, at a moderate energy cost. This process opens prospects for applications requiring the transmission of laser beams through fogs and clouds.

  8. Welding and cutting

    International Nuclear Information System (INIS)

    Drews, P.; Schulze Frielinghaus, W.

    1978-01-01

    This is a survey, with 198 literature references, of the papers published in the fields of welding and cutting within the last three years. The subjects dealt with are: weldability of the materials - Welding methods - Thermal cutting - Shaping and calculation of welded joints - Environmental protection in welding and cutting. (orig.) [de

  9. A cut locus for finite graphs and the farthest point mapping

    DEFF Research Database (Denmark)

    Maddaloni, Alessandro; Zamfirescu, Carol T.

    2016-01-01

    We reflect upon an analogue of the cut locus, a notion classically studied in Differential Geometry, for finite graphs. The cut locus C(x) of a vertex x shall be the graph induced by the set of all vertices y with the property that no shortest path between x and z, z≠y, contains y. The cut locus ...

  10. Device for cutting protrusions

    Science.gov (United States)

    Bzorgi, Fariborz M [Knoxville, TN

    2011-07-05

    An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade. The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.

  11. Cutting Method of the CAD model of the Nuclear facility for Dismantling Simulation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ikjune; Choi, ByungSeon; Hyun, Dongjun; Jeong, KwanSeong; Kim, GeunHo; Lee, Jonghwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Current methods for process simulation cannot simulate the cutting operation flexibly. As is, to simulate a cutting operation, user needs to prepare the result models of cutting operation based on pre-define cutting path, depth and thickness with respect to a dismantle scenario in advance. And those preparations should be built again as scenario changes. To be, user can change parameters and scenarios dynamically within a simulation configuration process so that the user saves time and efforts to simulate cutting operations. This study presents the methodology of cutting operation which can be applied to all the procedure in the simulation of dismantling of nuclear facilities. We developed the cutting simulation module for cutting operation in the dismantling of the nuclear facilities based on proposed cutting methodology. We defined the requirement of model cutting methodology based on the requirement of the dismantling of nuclear facilities. And we implemented cutting simulation module based on API of the commercial CAD system.

  12. Learning from history : Changes and path dependency in the social housing sector in Austria, France and the Netherlands (1889-2008), Chapter 3

    NARCIS (Netherlands)

    Lévy-Vroelant, C.; Reinprecht, C.; Wassenberg, F.

    2008-01-01

    European social housing history can be interpreted through the combination of two complementary notions: path dependency and change. Socio-political experiences and practices at the national, regional or municipal level are potentially powerful determinants of historical developments—an idea known

  13. Fractional path planning and path tracking

    International Nuclear Information System (INIS)

    Melchior, P.; Jallouli-Khlif, R.; Metoui, B.

    2011-01-01

    This paper presents the main results of the application of fractional approach in path planning and path tracking. A new robust path planning design for mobile robot was studied in dynamic environment. The normalized attractive force applied to the robot is based on a fictitious fractional attractive potential. This method allows to obtain robust path planning despite robot mass variation. The danger level of each obstacles is characterized by the fractional order of the repulsive potential of the obstacles. Under these conditions, the robot dynamic behavior was studied by analyzing its X - Y path planning with dynamic target or dynamic obstacles. The case of simultaneously mobile obstacles and target is also considered. The influence of the robot mass variation is studied and the robustness analysis of the obtained path shows the robustness improvement due to the non integer order properties. Pre shaping approach is used to reduce system vibration in motion control. Desired systems inputs are altered so that the system finishes the requested move without residual vibration. This technique, developed by N.C. Singer and W.P.Seering, is used for flexible structure control, particularly in the aerospace field. In a previous work, this method was extended for explicit fractional derivative systems and applied to second generation CRONE control, the robustness was also studied. CRONE (the French acronym of C ommande Robuste d'Ordre Non Entier ) control system design is a frequency-domain based methodology using complex fractional integration.

  14. Extension without Cut

    OpenAIRE

    Straßburger , Lutz

    2012-01-01

    International audience; In proof theory one distinguishes sequent proofs with cut and cut-free sequent proofs, while for proof complexity one distinguishes Frege-systems and extended Frege-systems. In this paper we show how deep inference can provide a uniform treatment for both classifications, such that we can define cut-free systems with extension, which is neither possible with Frege-systems, nor with the sequent calculus. We show that the propositional pigeon-hole principle admits polyno...

  15. Underwater cutting techniques developments

    International Nuclear Information System (INIS)

    Bach, F.-W.

    1990-01-01

    The primary circuit structures of different nuclear powerplants are constructed out of stainless steels, ferritic steels, plated ferritic steels and alloys of aluminium. According to the level of the specific radiation of these structures, it is necessary for dismantling to work with remote controlled cutting techniques. The most successful way to protect the working crew against exposure of radiation is to operate underwater in different depths. The following thermal cutting processes are more or less developed to work under water: For ferritic steels only - flame cutting; For ferritic steels, stainless steels, cladded steels and aluminium alloys - oxy-arc-cutting, arc-waterjet-cutting with a consumable electrode, arc-saw-cutting, plasma-arc-cutting and plasma-arc-saw. The flame cutting is a burning process, all the other processes are melt-cutting processes. This paper explains the different techniques, giving a short introduction of the theory, a discussion of the possibilities with the advantages and disadvantages of these processes giving a view into the further research work in this interesting field. (author)

  16. Cutting Class Harms Grades

    Science.gov (United States)

    Taylor, Lewis A., III

    2012-01-01

    An accessible business school population of undergraduate students was investigated in three independent, but related studies to determine effects on grades due to cutting class and failing to take advantage of optional reviews and study quizzes. It was hypothesized that cutting classes harms exam scores, attending preexam reviews helps exam…

  17. Path-dependent functions

    International Nuclear Information System (INIS)

    Khrapko, R.I.

    1985-01-01

    A uniform description of various path-dependent functions is presented with the help of expansion of the type of the Taylor series. So called ''path-integrals'' and ''path-tensor'' are introduced which are systems of many-component quantities whose values are defined for arbitrary paths in coordinated region of space in such a way that they contain a complete information on the path. These constructions are considered as elementary path-dependent functions and are used instead of power monomials in the usual Taylor series. Coefficients of such an expansion are interpreted as partial derivatives dependent on the order of the differentiations or else as nonstandard cavariant derivatives called two-point derivatives. Some examples of pathdependent functions are presented.Space curvature tensor is considered whose geometrica properties are determined by the (non-transitive) translator of parallel transport of a general type. Covariant operation leading to the ''extension'' of tensor fiels is pointed out

  18. The impulse cutoff an entropy functional measure on trajectories of Markov diffusion process integrating in information path functional

    OpenAIRE

    Lerner, Vladimir S.

    2012-01-01

    The impulses, cutting entropy functional (EF) measure on trajectories Markov diffusion process, integrate information path functional (IPF) composing discrete information Bits extracted from observing random process. Each cut brings memory of the cutting entropy, which provides both reduction of the process entropy and discrete unit of the cutting entropy a Bit. Consequently, information is memorized entropy cutting in random observations which process interactions. The origin of information ...

  19. Fundamentals of cutting.

    Science.gov (United States)

    Williams, J G; Patel, Y

    2016-06-06

    The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology.

  20. Iterated Leavitt Path Algebras

    International Nuclear Information System (INIS)

    Hazrat, R.

    2009-11-01

    Leavitt path algebras associate to directed graphs a Z-graded algebra and in their simplest form recover the Leavitt algebras L(1,k). In this note, we introduce iterated Leavitt path algebras associated to directed weighted graphs which have natural ± Z grading and in their simplest form recover the Leavitt algebras L(n,k). We also characterize Leavitt path algebras which are strongly graded. (author)

  1. Investigation of tool engagement and cutting performance in machining a pocket

    Science.gov (United States)

    Adesta, E. Y. T.; Hamidon, R.; Riza, M.; Alrashidi, R. F. F. A.; Alazemi, A. F. F. S.

    2018-01-01

    This study investigates the variation of tool engagement for different profile of cutting. In addition, behavior of cutting force and cutting temperature for different tool engagements for machining a pocket also been explored. Initially, simple tool engagement models were developed for peripheral and slot cutting for different types of corner. Based on these models, the tool engagements for contour and zig zag tool path strategies for a rectangular shape pocket with dimension 80 mm x 60 mm were analyzed. Experiments were conducted to investigate the effect of tool engagements on cutting force and cutting temperature for the machining of a pocket of AISI H13 material. The cutting parameters used were 150m/min cutting speed, 0.05mm/tooth feed, and 0.1mm depth of cut. Based on the results obtained, the changes of cutting force and cutting temperature performance there exist a relationship between cutting force, cutting temperature and tool engagement. A higher cutting force and cutting temperature is obtained when the cutting tool goes through up milling and when the cutting tool makes a full engagement with the workpiece.

  2. Pulled Motzkin paths

    Energy Technology Data Exchange (ETDEWEB)

    Janse van Rensburg, E J, E-mail: rensburg@yorku.c [Department of Mathematics and Statistics, York University, Toronto, ON, M3J 1P3 (Canada)

    2010-08-20

    In this paper the models of pulled Dyck paths in Janse van Rensburg (2010 J. Phys. A: Math. Theor. 43 215001) are generalized to pulled Motzkin path models. The generating functions of pulled Motzkin paths are determined in terms of series over trinomial coefficients and the elastic response of a Motzkin path pulled at its endpoint (see Orlandini and Whittington (2004 J. Phys. A: Math. Gen. 37 5305-14)) is shown to be R(f) = 0 for forces pushing the endpoint toward the adsorbing line and R(f) = f(1 + 2cosh f))/(2sinh f) {yields} f as f {yields} {infinity}, for forces pulling the path away from the X-axis. In addition, the elastic response of a Motzkin path pulled at its midpoint is shown to be R(f) = 0 for forces pushing the midpoint toward the adsorbing line and R(f) = f(1 + 2cosh (f/2))/sinh (f/2) {yields} 2f as f {yields} {infinity}, for forces pulling the path away from the X-axis. Formal combinatorial identities arising from pulled Motzkin path models are also presented. These identities are the generalization of combinatorial identities obtained in directed paths models to their natural trinomial counterparts.

  3. Pulled Motzkin paths

    Science.gov (United States)

    Janse van Rensburg, E. J.

    2010-08-01

    In this paper the models of pulled Dyck paths in Janse van Rensburg (2010 J. Phys. A: Math. Theor. 43 215001) are generalized to pulled Motzkin path models. The generating functions of pulled Motzkin paths are determined in terms of series over trinomial coefficients and the elastic response of a Motzkin path pulled at its endpoint (see Orlandini and Whittington (2004 J. Phys. A: Math. Gen. 37 5305-14)) is shown to be R(f) = 0 for forces pushing the endpoint toward the adsorbing line and R(f) = f(1 + 2cosh f))/(2sinh f) → f as f → ∞, for forces pulling the path away from the X-axis. In addition, the elastic response of a Motzkin path pulled at its midpoint is shown to be R(f) = 0 for forces pushing the midpoint toward the adsorbing line and R(f) = f(1 + 2cosh (f/2))/sinh (f/2) → 2f as f → ∞, for forces pulling the path away from the X-axis. Formal combinatorial identities arising from pulled Motzkin path models are also presented. These identities are the generalization of combinatorial identities obtained in directed paths models to their natural trinomial counterparts.

  4. Pulled Motzkin paths

    International Nuclear Information System (INIS)

    Janse van Rensburg, E J

    2010-01-01

    In this paper the models of pulled Dyck paths in Janse van Rensburg (2010 J. Phys. A: Math. Theor. 43 215001) are generalized to pulled Motzkin path models. The generating functions of pulled Motzkin paths are determined in terms of series over trinomial coefficients and the elastic response of a Motzkin path pulled at its endpoint (see Orlandini and Whittington (2004 J. Phys. A: Math. Gen. 37 5305-14)) is shown to be R(f) = 0 for forces pushing the endpoint toward the adsorbing line and R(f) = f(1 + 2cosh f))/(2sinh f) → f as f → ∞, for forces pulling the path away from the X-axis. In addition, the elastic response of a Motzkin path pulled at its midpoint is shown to be R(f) = 0 for forces pushing the midpoint toward the adsorbing line and R(f) = f(1 + 2cosh (f/2))/sinh (f/2) → 2f as f → ∞, for forces pulling the path away from the X-axis. Formal combinatorial identities arising from pulled Motzkin path models are also presented. These identities are the generalization of combinatorial identities obtained in directed paths models to their natural trinomial counterparts.

  5. Comparison of classical reaction paths and tunneling paths studied with the semiclassical instanton theory.

    Science.gov (United States)

    Meisner, Jan; Markmeyer, Max N; Bohner, Matthias U; Kästner, Johannes

    2017-08-30

    Atom tunneling in the hydrogen atom transfer reaction of the 2,4,6-tri-tert-butylphenyl radical to 3,5-di-tert-butylneophyl, which has a short but strongly curved reaction path, was investigated using instanton theory. We found the tunneling path to deviate qualitatively from the classical intrinsic reaction coordinate, the steepest-descent path in mass-weighted Cartesian coordinates. To perform that comparison, we implemented a new variant of the predictor-corrector algorithm for the calculation of the intrinsic reaction coordinate. We used the reaction force analysis method as a means to decompose the reaction barrier into structural and electronic components. Due to the narrow energy barrier, atom tunneling is important in the abovementioned reaction, even above room temperature. Our calculated rate constants between 350 K and 100 K agree well with experimental values. We found a H/D kinetic isotope effect of almost 10 6 at 100 K. Tunneling dominates the protium transfer below 400 K and the deuterium transfer below 300 K. We compared the lengths of the tunneling path and the classical path for the hydrogen atom transfer in the reaction HCl + Cl and quantified the corner cutting in this reaction. At low temperature, the tunneling path is about 40% shorter than the classical path.

  6. Advanced cutting techniques: laser and fissuration cutting

    International Nuclear Information System (INIS)

    Migliorati, B.; Gay, P.

    1984-01-01

    Experimental tests have been performed using CO 2 laser with output power 1 to 15 kW to evaluate the effect of varying the following parameters: material (carbon steel Fe 42 C, stainless steel AISI 304, concrete), laser power, beam characteristics, work piece velocity, gas type and distribution on the laser interaction zone. In the case of concrete, drilling depths of 80 mm were obtained in a few seconds using a 10 kW laser beam. Moreover pieces of 160 mm were cut at 0.01 meters per minute. Results with carbon steel indicated maximum thicknesses of 110 mm, cut at 0.01 meters per minute with 10 kW, depths about 20% lower were obtained with the AISI 304 stainless steel. A parallel investigation was aimed at characterizing particulate emission during the laser cutting process. At the end of the research it was possible to elaborate a preliminary proposal concerning a laser based dismantling system for the application to a typical Nuclear Power Station. (author)

  7. Multi-Dimensional Path Queries

    DEFF Research Database (Denmark)

    Bækgaard, Lars

    1998-01-01

    to create nested path structures. We present an SQL-like query language that is based on path expressions and we show how to use it to express multi-dimensional path queries that are suited for advanced data analysis in decision support environments like data warehousing environments......We present the path-relationship model that supports multi-dimensional data modeling and querying. A path-relationship database is composed of sets of paths and sets of relationships. A path is a sequence of related elements (atoms, paths, and sets of paths). A relationship is a binary path...

  8. Laser Cutting, Development Trends

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    1999-01-01

    In this paper a short review of the development trends in laser cutting will be given.The technology, which is the fastest expanding industrial production technology will develop in both its core market segment: Flat bed cutting of sheet metal, as it will expand in heavy industry and in cutting...... of 3-dimensional shapes.The CO2-laser will also in the near future be the dominating laser source in the market, although the new developments in ND-YAG-lasers opens for new possibilities for this laser type....

  9. Unique Path Partitions

    DEFF Research Database (Denmark)

    Bessenrodt, Christine; Olsson, Jørn Børling; Sellers, James A.

    2013-01-01

    We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions.......We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions....

  10. Hamiltonian path integrals

    International Nuclear Information System (INIS)

    Prokhorov, L.V.

    1982-01-01

    The properties of path integrals associated with the allowance for nonstandard terms reflecting the operator nature of the canonical variables are considered. Rules for treating such terms (''equivalence rules'') are formulated. Problems with a boundary, the behavior of path integrals under canonical transformations, and the problem of quantization of dynamical systems with constraints are considered in the framework of the method

  11. GeoMapApp Learning Activities: Grab-and-go inquiry-based geoscience activities that bring cutting-edge technology to the classroom

    Science.gov (United States)

    Goodwillie, A. M.; Kluge, S.

    2011-12-01

    NSF-funded GeoMapApp Learning Activities (http://serc.carleton.edu/geomapapp) provide self-contained learning opportunities that are centred around the principles of guided inquiry. The activities allow students to interact with and analyse research-quality geoscience data to explore and enhance student understanding of underlying geoscience content and concepts. Each activity offers ready-to-use step-by-step student instructions and answer sheets that can be downloaded from the web page. Also provided are annotated teacher versions of the worksheets that include teaching tips, additional content and suggestions for further work. Downloadable pre- and post- quizzes tied to each activity help educators gauge the learning progression of their students. Short multimedia tutorials and details on content alignment with state and national teaching standards round out the package of material that comprises each "grab-and-go" activity. GeoMapApp Learning Activities expose students to content and concepts typically found at the community college, high school and introductory undergraduate levels. The activities are based upon GeoMapApp (http://www.geomapapp.org), a free, easy-to-use map-based data exploration and visualisation tool that allows students to access a wide range of geoscience data sets in a virtual lab-like environment. Activities that have so far been created under this project include student exploration of seafloor spreading rates, a study of mass wasting as revealed through geomorphological evidence, and an analysis of plate motion and hotspot traces. The step-by-step instructions and guided inquiry approach lead students through each activity, thus reducing the need for teacher intervention whilst also boosting the time that students can spend on productive exploration and learning. The activities can be used, for example, in a classroom lab with the educator present and as self-paced assignments in an out-of-class setting. GeoMapApp Learning Activities

  12. Experimental testing of exchangeable cutting inserts cutting ability

    OpenAIRE

    Čep, Robert; Janásek, Adam; Čepová, Lenka; Petrů, Jana; Hlavatý, Ivo; Car, Zlatan; Hatala, Michal

    2013-01-01

    The article deals with experimental testing of the cutting ability of exchangeable cutting inserts. Eleven types of exchangeable cutting inserts from five different manufacturers were tested. The tested cutting inserts were of the same shape and were different especially in material and coating types. The main aim was both to select a suitable test for determination of the cutting ability of exchangeable cutting inserts and to design such testing procedure that could make it possible...

  13. The formal path integral and quantum mechanics

    International Nuclear Information System (INIS)

    Johnson-Freyd, Theo

    2010-01-01

    Given an arbitrary Lagrangian function on R d and a choice of classical path, one can try to define Feynman's path integral supported near the classical path as a formal power series parameterized by 'Feynman diagrams', although these diagrams may diverge. We compute this expansion and show that it is (formally, if there are ultraviolet divergences) invariant under volume-preserving changes of coordinates. We prove that if the ultraviolet divergences cancel at each order, then our formal path integral satisfies a 'Fubini theorem' expressing the standard composition law for the time evolution operator in quantum mechanics. Moreover, we show that when the Lagrangian is inhomogeneous quadratic in velocity such that its homogeneous-quadratic part is given by a matrix with constant determinant, then the divergences cancel at each order. Thus, by 'cutting and pasting' and choosing volume-compatible local coordinates, our construction defines a Feynman-diagrammatic 'formal path integral' for the nonrelativistic quantum mechanics of a charged particle moving in a Riemannian manifold with an external electromagnetic field.

  14. Cut without Killing.

    Science.gov (United States)

    Black, Susan

    1991-01-01

    The zero-based curriculum model can help school boards and administrators make decisions about what to keep and what to cut. All instructional programs are ranked and judged in categories ranging from required to optional. (MLF)

  15. Short-cut math

    CERN Document Server

    Kelly, Gerard W

    1984-01-01

    Clear, concise compendium of about 150 time-saving math short-cuts features faster, easier ways to add, subtract, multiply, and divide. Each problem includes an explanation of the method. No special math ability needed.

  16. Analysis Of Economic Motivation When Individuals Choose An Educational Path

    Directory of Open Access Journals (Sweden)

    Viktor Anatolyevich Koksharov

    2015-03-01

    Full Text Available The authors consider the economic motivations when individuals choose an educational path. This line of research is relevant from both, the point of view of science — research of economic behavior of an individual, and the point of view of practice — allows to increase efficiency of investments in a human capital. The authors have developed the economic and mathematical model of choice of optimum educational paths by individuals. The model is realized in the software and approved on real data on more than 5,5 thousand students. For the analysis of the importance of rational economic expectations when an educational path has to be chosen, the paths chosen by students is compared and the educational paths optimum from the point of view of economic rationality are calculated. The analysis of the results has showed that mainly, the choice of educational paths happens according to the economic motivations. On the considered selection, 66 % of prospective students have chosen an optimum path from the point of view of economic preferences. The most significant factor providing development of optimum educational paths is an expectation of higher income upon completion of education — 22 % of all educational paths, and a possibility of cost-cutting of educating or state-subsidized education — 12 %. In our opinion, one of the most important practical results of the research of optimum educational path is the need to consider expectations of students and prospective student when developing a state policy of investment in human capital.

  17. Laser cutting system

    Science.gov (United States)

    Dougherty, Thomas J

    2015-03-03

    A workpiece cutting apparatus includes a laser source, a first suction system, and a first finger configured to guide a workpiece as it moves past the laser source. The first finger includes a first end provided adjacent a point where a laser from the laser source cuts the workpiece, and the first end of the first finger includes an aperture in fluid communication with the first suction system.

  18. How Can I Stop Cutting?

    Science.gov (United States)

    ... Educators Search English Español How Can I Stop Cutting? KidsHealth / For Teens / How Can I Stop Cutting? ... in a soft, cozy blanket Substitutes for the Cutting Sensation You'll notice that all the tips ...

  19. Cutting and Self-Harm

    Science.gov (United States)

    ... Your feelings Feeling sad Cutting and self-harm Cutting and self-harm Self-harm, sometimes called self- ... There are many types of self-injury, and cutting is one type that you may have heard ...

  20. Flux cutting in superconductors

    International Nuclear Information System (INIS)

    Campbell, A M

    2011-01-01

    This paper describes experiments and theories of flux cutting in superconductors. The use of the flux line picture in free space is discussed. In superconductors cutting can either be by means of flux at an angle to other layers of flux, as in longitudinal current experiments, or due to shearing of the vortex lattice as in grain boundaries in YBCO. Experiments on longitudinal currents can be interpreted in terms of flux rings penetrating axial lines. More physical models of flux cutting are discussed but all predict much larger flux cutting forces than are observed. Also, cutting is occurring at angles between vortices of about one millidegree which is hard to explain. The double critical state model and its developments are discussed in relation to experiments on crossed and rotating fields. A new experiment suggested by Clem gives more direct information. It shows that an elliptical yield surface of the critical state works well, but none of the theoretical proposals for determining the direction of E are universally applicable. It appears that, as soon as any flux flow takes place, cutting also occurs. The conclusion is that new theories are required. (perspective)

  1. On Permuting Cut with Contraction

    OpenAIRE

    Borisavljevic, Mirjana; Dosen, Kosta; Petric, Zoran

    1999-01-01

    The paper presents a cut-elimination procedure for intuitionistic propositional logic in which cut is eliminated directly, without introducing the multiple-cut rule mix, and in which pushing cut above contraction is one of the reduction steps. The presentation of this procedure is preceded by an analysis of Gentzen's mix-elimination procedure, made in the perspective of permuting cut with contraction. It is also shown that in the absence of implication, pushing cut above contraction doesn't p...

  2. Optimized path planning for soft tissue resection via laser vaporization

    Science.gov (United States)

    Ross, Weston; Cornwell, Neil; Tucker, Matthew; Mann, Brian; Codd, Patrick

    2018-02-01

    Robotic and robotic-assisted surgeries are becoming more prevalent with the promise of improving surgical outcomes through increased precision, reduced operating times, and minimally invasive procedures. The handheld laser scalpel in neurosurgery has been shown to provide a more gentle approach to tissue manipulation on or near critical structures over classical tooling, though difficulties of control have prevented large scale adoption of the tool. This paper presents a novel approach to generating a cutting path for the volumetric resection of tissue using a computer-guided laser scalpel. A soft tissue ablation simulator is developed and used in conjunction with an optimization routine to select parameters which maximize the total resection of target tissue while minimizing the damage to surrounding tissue. The simulator predicts the ablative properties of tissue from an interrogation cut for tuning and simulates the removal of a tumorous tissue embedded on the surface of healthy tissue using a laser scalpel. We demonstrate the ability to control depth and smoothness of cut using genetic algorithms to optimize the ablation parameters and cutting path. The laser power level, cutting rate and spacing between cuts are optimized over multiple surface cuts to achieve the desired resection volumes.

  3. Path integration quantization

    International Nuclear Information System (INIS)

    DeWitt-Morette, C.

    1983-01-01

    Much is expected of path integration as a quantization procedure. Much more is possible if one recognizes that path integration is at the crossroad of stochastic and differential calculus and uses the full power of both stochastic and differential calculus in setting up and computing path integrals. In contrast to differential calculus, stochastic calculus has only comparatively recently become an instrument of thought. It has nevertheless already been used in a variety of challenging problems, for instance in the quantization problem. The author presents some applications of the stochastic scheme. (Auth.)

  4. Two dimensional simplicial paths

    International Nuclear Information System (INIS)

    Piso, M.I.

    1994-07-01

    Paths on the R 3 real Euclidean manifold are defined as 2-dimensional simplicial strips which are orbits of the action of a discrete one-parameter group. It is proven that there exists at least one embedding of R 3 in the free Z-module generated by S 2 (x 0 ). The speed is defined as the simplicial derivative of the path. If mass is attached to the simplex, the free Lagrangian is proportional to the width of the path. In the continuum limit, the relativistic form of the Lagrangian is recovered. (author). 7 refs

  5. Developing a Multidimensional Checklist for Evaluating Language-Learning Websites Coherent with the Communicative Approach: A Path for the Knowing-How-to-Do Enhancement

    Science.gov (United States)

    Moncada Linares, Sthephanny; Díaz Romero, Andrea Carolina

    2016-01-01

    As a result of the rapid development of Information and Communication Technology (ICT) and the growing interest in Internet-based tools for language classroom, it has become a pressing need for educators to locate, evaluate and select the most appropriate language-learning digital resources that foster more communicative and meaningful learning…

  6. Female genital cutting.

    Science.gov (United States)

    Perron, Liette; Senikas, Vyta; Burnett, Margaret; Davis, Victoria

    2013-11-01

    To strengthen the national framework for care of adolescents and women affected by female genital cutting (FGC) in Canada by providing health care professionals with: (1) information intended to strengthen their knowledge and understanding of the practice; (2) directions with regard to the legal issues related to the practice; (3) clinical guidelines for the management of obstetric and gynaecological care, including FGC related complications; and (4) guidance on the provision of culturally competent care to adolescents and women with FGC. Published literature was retrieved through searches of PubMed, CINAHL, and The Cochrane Library in September 2010 using appropriate controlled vocabulary (e.g., Circumcision, Female) and keywords (e.g., female genital mutilation, clitoridectomy, infibulation). We also searched Social Science Abstracts, Sociological Abstracts, Gender Studies Database, and ProQuest Dissertations and Theses in 2010 and 2011. There were no date or language restrictions. Searches were updated on a regular basis and incorporated in the guideline to December 2011. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table 1). Summary Statements 1. Female genital cutting is internationally recognized as a harmful practice and a violation of girls' and women's rights to life, physical integrity, and health. (II-3) 2. The immediate and long-term health risks and complications of female genital cutting can be serious and life threatening. (II-3) 3. Female genital cutting continues to be practised in many countries, particularly in sub-Saharan Africa, Egypt, and Sudan. (II-3) 4. Global migration

  7. Zero-Slack, Noncritical Paths

    Science.gov (United States)

    Simons, Jacob V., Jr.

    2017-01-01

    The critical path method/program evaluation and review technique method of project scheduling is based on the importance of managing a project's critical path(s). Although a critical path is the longest path through a network, its location in large projects is facilitated by the computation of activity slack. However, logical fallacies in…

  8. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

    2003-09-30

    The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

  9. Improved cutting performance in high power laser cutting

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    2003-01-01

    Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

  10. The CLEM model: Path analysis of the mediating effects of attitudes and motivational beliefs on the relationship between perceived learning environment and course performance in an undergraduate nonmajor biology course

    Science.gov (United States)

    Partin, Matthew L.

    The problem addressed in this study stems from three crises currently faced by post-secondary science educators in the United States: relatively low scientific literacy among students entering college, the need for more students to pursue science related careers, and poor attitudes among students toward studying science. In this dissertation the following questions are addressed: Is there a relationship between students' perceptions of their learning environment and course performance, and what roles do motivation and attitudes play in mediating that relationship? This study also examines the effects of gender and ethnicity on motivation, attitudes, and course performance. The purpose of this study is to test a path model describing the mediating effects of motivation and attitudes on constructivist learning environments and course performance. The following study considers contemporary understanding of teaching and learning as well as motivation and attitudes to suggest a direction for future reform efforts and to guide post-secondary science education instructors and leaders in the design of constructivist learning environments for undergraduate nonmajor biology courses. This study concludes that, although the classroom learning environment has a small direct effect on course performance, there is a moderate total effect on self-efficacy and intrinsic goal orientation. The classroom learning environment also had a moderate indirect effect on attitudes toward biology. Furthermore, attitudes have a moderate direct effect on course performance and self-efficacy has a strong direct effect on both course performance and attitudes toward biology. Self-efficacy seems to be particularly important; however, each of these constructs is important in its own right and instructors in higher education should strive to enhance each of them among their students. If students are to learn using constructivist methods they need the proper motivation and positive attitudes to

  11. Groebner Finite Path Algebras

    OpenAIRE

    Leamer, Micah J.

    2004-01-01

    Let K be a field and Q a finite directed multi-graph. In this paper I classify all path algebras KQ and admissible orders with the property that all of their finitely generated ideals have finite Groebner bases. MS

  12. Determination of cut front position in laser cutting

    International Nuclear Information System (INIS)

    Pereira, M; Thombansen, U

    2016-01-01

    Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable. (paper)

  13. Determination of cut front position in laser cutting

    Science.gov (United States)

    Pereira, M.; Thombansen, U.

    2016-07-01

    Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable.

  14. Cutting thin glass by femtosecond laser ablation

    Science.gov (United States)

    Shin, Hyesung; Kim, Dongsik

    2018-06-01

    The femtosecond laser ablation process for cutting thin aluminoborosilicate glass sheets of thickness 100 μm was investigated with emphasis on effective cutting speed (Veff) and mechanical strength of diced samples. The process parameters including the laser fluence (F), overlap ratio (r) of the laser beam and polarization direction were varied at a fixed pulse repetition rate f = 1 kHz to find the optimal process condition that maximizes Veff and edge strength. A three-point bending test was performed to evaluate the front-side and back-side bending (edge) strength of the laser-cut samples. Veff was proportional to F unless r exceeded a critical value, at which excessive energy began to be delivered at the same spot. The front-side edge strength was bigger than the back-side strength because of the back-side damages such as chipping. Good edge strength, as high as ∼280 MPa (front-side) and ∼230 MPa (back-side), was obtained at F = 19 J/m2, r = 0.99, with laser polarization vertical to the cutting path.

  15. Path planning in changeable environments

    NARCIS (Netherlands)

    Nieuwenhuisen, D.

    2007-01-01

    This thesis addresses path planning in changeable environments. In contrast to traditional path planning that deals with static environments, in changeable environments objects are allowed to change their configurations over time. In many cases, path planning algorithms must facilitate quick

  16. Underwater plasma arc cutting

    International Nuclear Information System (INIS)

    Leautier, R.; Pilot, G.

    1991-01-01

    This report describes the work done to develop underwater plasma arc cutting techniques, to characterise aerosols from cutting operations on radioactive and non-radioactive work-pieces, and to develop suitable ventilation and filtration techniques. The work has been carried out in the framework of a contract between CEA-CEN Cadarache and the Commission of European Communities. Furthermore, this work has been carried out in close cooperation with CEA-CEN Saclay mainly for secondary emissions and radioactive analysis. The contract started in May 1986 and was completed in December 1988 by a supplementary agreement. This report has been compiled from several progress reports submitted during the work period, contains the main findings of the work and encloses the results of comparative tests on plasma arc cutting

  17. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Lei Zhou

    2000-01-30

    This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members. The tasks Completed During This Quarter are Task 7 and Task 8.

  18. Theoretical Models for Orthogonal Cutting

    DEFF Research Database (Denmark)

    De Chiffre, Leonardo

    This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”......This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”...

  19. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Stefan Miska; Troy Reed; Ergun Kuru

    2004-09-30

    The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a

  20. The neural evidence of the reflected appraisal process as a main path for learning about one's self-knowledge of personality.

    Science.gov (United States)

    Xu, Xiaofan; Chen, Yu; Zhao, Yufang; Yang, Juan

    2015-09-01

    Self-knowledge has been defined as the accurate self-perceptions about how one typically thinks, feels, and behaves, and awareness of how those patterns are interpreted by others. Previous research has noted that the introspection and the reflected appraisal processes are two main avenues for learning about the self and that self-knowledge might be fully realized through the use of reflected appraisal from close others. However, due to the methodological difficulty in linking people's ratings on a trait to their behaviors, accuracy research using a behavioral criterion is quite limited. The current work examined the main source of learning about one's self-knowledge by investigating the time course of attention deployment both in the process of introspection and that of reflected appraisal. Twenty-five college students were first asked to rate their impressions of their classmates as well as a familiar other using personality-trait adjectives. Their electrophysiological data were then collected using the event-related potential (ERP) technology while they judged to which extent (1) an adjective can describe the self, (2) an adjective can describe a familiar other, (3) they agree with an adjective that their classmates believe can describe the self, and (4) they agree with an adjective that their classmates believe can describe a familiar other. Our electrophysiological data showed that classmates' positive evaluation of one's own trait elicited larger P2 than the positive self-evaluation of one's own trait. Further, classmates' negative evaluation of one's own trait elicited larger late positive component (LPC) than the negative self-evaluation of one's own trait. Results suggest that people allocate more attention to the process of reflected appraisal compared to the process of introspection, which further suggests that the reflected appraisal process might be the main source in learning about one's self-knowledge of personality. Copyright © 2015 Elsevier B

  1. Opening Remarks of the Acquisition Path Analysis Methodology Session

    International Nuclear Information System (INIS)

    Renis, T.

    2015-01-01

    An overview of the recent development work that has been done on acquisition path analysis, implementation of the methodologies within the Department of Safeguards, lessons learned and future areas for development will be provided. (author)

  2. Quivers of Bound Path Algebras and Bound Path Coalgebras

    Directory of Open Access Journals (Sweden)

    Dr. Intan Muchtadi

    2010-09-01

    Full Text Available bras and coalgebras can be represented as quiver (directed graph, and from quiver we can construct algebras and coalgebras called path algebras and path coalgebras. In this paper we show that the quiver of a bound path coalgebra (resp. algebra is the dual quiver of its bound path algebra (resp. coalgebra.

  3. Skin Cut Construction

    DEFF Research Database (Denmark)

    2017-01-01

    of the exhibition is to create a connection between the artistic and technological development through Danish rms and researchers who represent the newest technology in concrete treatment. The rst part exhibition (skin) will focus on the surface treatment of concrete (’graphical concrete’), the second (cut...

  4. Cutting Cakes Carefully

    Science.gov (United States)

    Hill, Theodore P.; Morrison, Kent E.

    2010-01-01

    This paper surveys the fascinating mathematics of fair division, and provides a suite of examples using basic ideas from algebra, calculus, and probability which can be used to examine and test new and sometimes complex mathematical theories and claims involving fair division. Conversely, the classical cut-and-choose and moving-knife algorithms…

  5. Classroom Cut Ups

    Science.gov (United States)

    Lord, Stacy

    2011-01-01

    Discovering identity can be a lifelong challenge for some people, while others seem to figure it out right away. During the middle school years, finding one's identity can be a daunting task. Most students will spend a considerable amount of time during these middle years looking for it. This lesson on cut-paper self-portraits lets students delve…

  6. Abrasive water jet cutting

    International Nuclear Information System (INIS)

    Leist, K.J.; Funnell, G.J.

    1988-01-01

    In the process of selecting a failed equipment cut-up tool for the process facility modifications (PFM) project, a system using an abrasive water jet (AWJ) was developed and tested for remote disassembly of failed equipment. It is presented in this paper

  7. After the Ribbon Cutting

    DEFF Research Database (Denmark)

    Hodge, Graeme A.; Boulot, Emille; Duffield, Colin

    2017-01-01

    Much attention has gone towards ‘up-front’ processes when delivering infrastructure public–private partnerships (PPPs), but less on how to best govern after the ribbon is cut and the infrastructure built. This paper identifies the primary contractual and institutional governance challenges arising...

  8. Simultaneous Cake Cutting

    DEFF Research Database (Denmark)

    Balkanski, Eric; Branzei, Simina; Kurokawa, David

    2014-01-01

    We introduce the simultaneous model for cake cutting (the fair allocation of a divisible good), in which agents simultaneously send messages containing a sketch of their preferences over the cake. We show that this model enables the computation of divisions that satisfy proportionality — a popular...

  9. Abrasive slurry jet cutting model based on fuzzy relations

    Science.gov (United States)

    Qiang, C. H.; Guo, C. W.

    2017-12-01

    The cutting process of pre-mixed abrasive slurry or suspension jet (ASJ) is a complex process affected by many factors, and there is a highly nonlinear relationship between the cutting parameters and cutting quality. In this paper, guided by fuzzy theory, the fuzzy cutting model of ASJ was developed. In the modeling of surface roughness, the upper surface roughness prediction model and the lower surface roughness prediction model were established respectively. The adaptive fuzzy inference system combines the learning mechanism of neural networks and the linguistic reasoning ability of the fuzzy system, membership functions, and fuzzy rules are obtained by adaptive adjustment. Therefore, the modeling process is fast and effective. In this paper, the ANFIS module of MATLAB fuzzy logic toolbox was used to establish the fuzzy cutting model of ASJ, which is found to be quite instrumental to ASJ cutting applications.

  10. Paths correlation matrix.

    Science.gov (United States)

    Qian, Weixian; Zhou, Xiaojun; Lu, Yingcheng; Xu, Jiang

    2015-09-15

    Both the Jones and Mueller matrices encounter difficulties when physically modeling mixed materials or rough surfaces due to the complexity of light-matter interactions. To address these issues, we derived a matrix called the paths correlation matrix (PCM), which is a probabilistic mixture of Jones matrices of every light propagation path. Because PCM is related to actual light propagation paths, it is well suited for physical modeling. Experiments were performed, and the reflection PCM of a mixture of polypropylene and graphite was measured. The PCM of the mixed sample was accurately decomposed into pure polypropylene's single reflection, pure graphite's single reflection, and depolarization caused by multiple reflections, which is consistent with the theoretical derivation. Reflection parameters of rough surface can be calculated from PCM decomposition, and the results fit well with the theoretical calculations provided by the Fresnel equations. These theoretical and experimental analyses verify that PCM is an efficient way to physically model light-matter interactions.

  11. Leavitt path algebras

    CERN Document Server

    Abrams, Gene; Siles Molina, Mercedes

    2017-01-01

    This book offers a comprehensive introduction by three of the leading experts in the field, collecting fundamental results and open problems in a single volume. Since Leavitt path algebras were first defined in 2005, interest in these algebras has grown substantially, with ring theorists as well as researchers working in graph C*-algebras, group theory and symbolic dynamics attracted to the topic. Providing a historical perspective on the subject, the authors review existing arguments, establish new results, and outline the major themes and ring-theoretic concepts, such as the ideal structure, Z-grading and the close link between Leavitt path algebras and graph C*-algebras. The book also presents key lines of current research, including the Algebraic Kirchberg Phillips Question, various additional classification questions, and connections to noncommutative algebraic geometry. Leavitt Path Algebras will appeal to graduate students and researchers working in the field and related areas, such as C*-algebras and...

  12. The Thinnest Path Problem

    Science.gov (United States)

    2016-07-22

    be reduced to TP in -D UDH for any . We then show that the 2-D disk hypergraph constructed in the proof of Theorem 1 can be modified to an exposed...transmission range that induces hy- peredge , i.e., (3) GAO et al.: THINNEST PATH PROBLEM 1181 Theorem 5 shows that the covered area of the path...representation of (the two hyperedges rooted at from the example given in Fig. 6 are illustrated in green and blue, respectively). step, we show in this

  13. Path dependence and creation

    DEFF Research Database (Denmark)

    Garud, Raghu; Karnøe, Peter

    This edited volume stems from a conference held in Copenhagen that the authors ran in August of 1997. The authors, aware of the recent work in evolutionary theory and the science of chaos and complexity, challenge the sometimes deterministic flavour of this work. They are interested in uncovering...... the place of agency in these theories that take history so seriously. In the end, they are as interested in path creation and destruction as they are in path dependence. This book is compiled of both theoretical and empirical writing. It shows relatively well-known industries such as the automobile...

  14. Reparametrization in the path integral

    International Nuclear Information System (INIS)

    Storchak, S.N.

    1983-01-01

    The question of the invariance of a measure in the n-dimensional path integral under the path reparametrization is considered. The non-invariance of the measure through the jacobian is suggeste. After the path integral reparametrization the representatioq for the Green's function of the Hamilton operator in terms of the path integral with the classical Hamiltonian has been obtained

  15. Core Cutting Test with Vertical Rock Cutting Rig (VRCR)

    Science.gov (United States)

    Yasar, Serdar; Osman Yilmaz, Ali

    2017-12-01

    Roadheaders are frequently used machines in mining and tunnelling, and performance prediction of roadheaders is important for project economics and stability. Several methods were proposed so far for this purpose and, rock cutting tests are the best choice. Rock cutting tests are generally divided into two groups which are namely, full scale rock cutting tests and small scale rock cutting tests. These two tests have some superiorities and deficiencies over themselves. However, in many cases, where rock sampling becomes problematic, small scale rock cutting test (core cutting test) is preferred for performance prediction, since small block samples and core samples can be conducted to rock cutting testing. Common problem for rock cutting tests are that they can be found in very limited research centres. In this study, a new mobile rock cutting testing equipment, vertical rock cutting rig (VRCR) was introduced. Standard testing procedure was conducted on seven rock samples which were the part of a former study on cutting rocks with another small scale rock cutting test. Results showed that core cutting test can be realized successfully with VRCR with the validation of paired samples t-test.

  16. Some possibilities for determining cutting data when using laser cutting:

    OpenAIRE

    Radovanović, Miroslav

    2006-01-01

    The technological problems faced in the field of the application of laser-cutting machines lie in insufficient knowledge of the laser technique and the absence of both sufficiently reliable practical data and knowledge about the parameters affecting the work process itself. A significant parameter that is necessary to determine and to enter in an NC-program is the cutting speed. Various authors analyze the laser-cutting process and give mathematical models where laser cutting is modeled by us...

  17. MEASURING PATH DEPENDENCY

    Directory of Open Access Journals (Sweden)

    Peter Juhasz

    2017-03-01

    Full Text Available While risk management gained popularity during the last decades even some of the basic risk types are still far out of focus. One of these is path dependency that refers to the uncertainty of how we reach a certain level of total performance over time. While decision makers are careful in accessing how their position will look like the end of certain periods, little attention is given how they will get there through the period. The uncertainty of how a process will develop across a shorter period of time is often “eliminated” by simply choosing a longer planning time interval, what makes path dependency is one of the most often overlooked business risk types. After reviewing the origin of the problem we propose and compare seven risk measures to access path. Traditional risk measures like standard deviation of sub period cash flows fail to capture this risk type. We conclude that in most cases considering the distribution of the expected cash flow effect caused by the path dependency may offer the best method, but we may need to use several measures at the same time to include all the optimisation limits of the given firm

  18. Cutting to the chase

    International Nuclear Information System (INIS)

    Snieckus, D.

    2001-01-01

    This article reports on the development of the cost effective abrasive cutting Sabre system which came as a result of UWG's work on the decommissioning of the Phillips' Maureen wells and adds to UWG's 'total severance solution' tools. The advantages of the system are highlighted and include the ability to operate from a platform or diving support vessel, to cut internal cases, and to eliminate the use of environmentally damaging explosives and the need to operate from a rig. The new Mark II version of the Sabre designed to work at greater depths of water, the range of the severance tools, UWG's well abandonment hole assembly system, and its aim to enter the Gulf of Mexico market are discussed. Details are given of the decommissioning of the Schwedeneck-See platforms in Kiel Bay off Germany and the Phillips' UK decommissioning plans for the Maureen platform

  19. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Neelima Godugu

    2000-07-30

    ACTS flow loop is now operational under elevated pressure and temperature. Currently, experiments with synthetic based drilling fluids under pressure and temperature are being conducted. Based on the analysis of Fann 70 data, empirical correlations defining the shear stress as a function of temperature, pressure and the shear rate have been developed for Petrobras synthetic drilling fluids. PVT equipment has been modified for testing Synthetic oil base drilling fluids. PVT tests with Petrobras Synthetic base mud have been conducted and results are being analyzed Foam flow experiments have been conducted and the analysis of the data has been carried out to characterize the rheology of the foam. Comparison of pressure loss prediction from the available foam hydraulic models and the test results has been made. Cuttings transport experiments in horizontal annulus section have been conducted using air, water and cuttings. Currently, cuttings transport tests in inclined test section are being conducted. Foam PVT analysis tests have been conducted. Foam stability experiments have also been conducted. Effects of salt and oil concentration on the foam stability have been investigated. Design of ACTS flow loop modification for foam and aerated mud flow has been completed. A flow loop operation procedure for conducting foam flow experiments under EPET conditions has been prepared Design of the lab-scale flow loop for dynamic foam characterization and cuttings monitoring instrumentation tests has been completed. The construction of the test loop is underway. As part of the technology transport efforts, Advisory Board Meeting with ACTS-JIP industry members has been organized on May 13, 2000.

  20. Making the cut

    Energy Technology Data Exchange (ETDEWEB)

    Mcshannon, G. [Hydra Mining Tools International Ltd. (United Kingdom)

    2006-04-15

    The paper explains how coal mines around the world can benefit from the use of cowless, radial shearer drums. Hydra Mining has designed and manufactured a range of shearer drums to combat problems ranging from dust, frictional ignitions, geological problems or low production rates. This allows the mine operator to maximise production efficiency. The company tailor-makes shearer drums for each longwall face to optimise the cutting performance of every installation. 8 figs.

  1. Cutting Out Continuations

    DEFF Research Database (Denmark)

    Bahr, Patrick; Hutton, Graham

    2016-01-01

    In the field of program transformation, one often transforms programs into continuation-passing style to make their flow of control explicit, and then immediately removes the resulting continuations using defunctionalisation to make the programs first-order. In this article, we show how these two...... transformations can be fused together into a single transformation step that cuts out the need to first introduce and then eliminate continuations. Our approach is calculational, uses standard equational reasoning techniques, and is widely applicable....

  2. Cutting forces during turning with variable depth of cut

    Directory of Open Access Journals (Sweden)

    M. Sadílek

    2016-03-01

    The proposed research for the paper is an experimental work – measuring cutting forces and monitoring of the tool wear on the cutting edge. It compares the turning where standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied.

  3. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Ergun Kuru; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Len Volk; Mark Pickell; Evren Ozbayoglu; Barkim Demirdal; Paco Vieira; Affonso Lourenco

    1999-10-15

    This report includes a review of the progress made in ACTF Flow Loop development and research during 90 days pre-award period (May 15-July 14, 1999) and the following three months after the project approval date (July15-October 15, 1999) The report presents information on the following specific subjects; (a) Progress in Advanced Cuttings Transport Facility design and development, (b) Progress report on the research project ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (c) Progress report on the research project ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (d) Progress report on the research project ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (e) Progress report on the research project ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Progress report on the instrumentation tasks (Tasks 11 and 12) (g) Activities towards technology transfer and developing contacts with oil and service company members.

  4. Vortex cutting in superconductors

    Science.gov (United States)

    Vlasko-Vlasov, Vitalii K.; Koshelev, Alexei E.; Glatz, Andreas; Welp, Ulrich; Kwok, Wai-K.

    2015-03-01

    Unlike illusive magnetic field lines in vacuum, magnetic vortices in superconductors are real physical strings, which interact with the sample surface, crystal structure defects, and with each other. We address the complex and poorly understood process of vortex cutting via a comprehensive set of magneto-optic experiments which allow us to visualize vortex patterns at magnetization of a nearly twin-free YBCO crystal by crossing magnetic fields of different orientations. We observe a pronounced anisotropy in the flux dynamics under crossing fields and the filamentation of induced supercurrents associated with the staircase vortex structure expected in layered cuprates, flux cutting effects, and angular vortex instabilities predicted for anisotropic superconductors. At some field angles, we find formation of the vortex domains following a type-I phase transition in the vortex state accompanied by an abrupt change in the vortex orientation. To clarify the vortex cutting scenario we performed time-dependent Ginzburg-Landau simulations, which confirmed formation of sharp vortex fronts observed in the experiment and revealed a left-handed helical instability responsible for the rotation of vortices. This work was supported by the U.S. Department of Energy, Office of Science, Materials Sciences and Engineering Division.

  5. Performance Testing of Cutting Fluids

    DEFF Research Database (Denmark)

    Belluco, Walter

    The importance of cutting fluid performance testing has increased with documentation requirements of new cutting fluid formulations based on more sustainable products, as well as cutting with minimum quantity of lubrication and dry cutting. Two sub-problems have to be solved: i) which machining...... tests feature repeatability, reproducibility and sensitivity to cutting fluids, and ii) to what extent results of one test ensure relevance to a wider set of machining situations. The present work is aimed at assessing the range of validity of the different testing methods, investigating correlation...... within the whole range of operations, materials, cutting fluids, operating conditions, etc. Cutting fluid performance was evaluated in turning, drilling, reaming and tapping, and with respect to tool life, cutting forces, chip formation and product quality (dimensional accuracy and surface integrity...

  6. CALCULATION OF LASER CUTTING COSTS

    OpenAIRE

    Bogdan Nedic; Milan Eric; Marijana Aleksijevic

    2016-01-01

    The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, compar...

  7. Remote Laser Cutting of CFRP: Improvements in the Cut Surface

    Science.gov (United States)

    Stock, Johannes; Zaeh, Michael F.; Conrad, Markus

    In the automotive industry carbon fibre reinforced plastics (CFRP) are considered as a future key material to reduce the weight of the vehicle. Therefore, capable production techniques are required to process this material in mass industry. E.g., state of the art methods for cutting are limited by the high tool wear or the feasible feed rate. Laser cutting processes are still under investigation. This paper presents detailed new studies on remote laser cutting of CFRP focusing on the influence of the material properties and the quality of the cut surface. By adding light absorbing soot particles to the resin of the matrix, the cutting process is improved and fewer defects emerge.

  8. Cutting agents for special metals

    International Nuclear Information System (INIS)

    Sugito, Seiji; Sakakibara, Fumi

    1979-01-01

    The quantity of use of special metals has increased year after year in the Plasma Research Institute, Nagoya University, with the development of researches on plasma and nuclear fusion. Most of these special metals are hard to cut, and in order to secure the surface smoothness and dimensional accuracy, considerable efforts are required. The method of experiment is as follows: cutting agents salt water and acetone, rape-seed oil, sulfide and chloride oil and water soluble cutting oil W grade 3; metals to be cut niobium, molybdenum, tantalum, titanium and tungsten; cutting conditions cutting speed 4.7 to 90 m/min, feed 0.07 to 0.2 mm/rev, depth of cut 0.1 to 0.4 mm, tool cemented carbide bit. Chemicals such as tetrachloromethane and trichloroethane give excellent cutting performance, but the toxicity is intense and the stimulative odor exists, accordingly they are hard to use practically. Cutting was easier when the salt water added with acetone was used than the case of rape-seed oil, but salt water is corrosive. Recently, the machining of molybdenum has been often carried out, and the water soluble cutting oil was the best. It is also good for cutting stainless steel, and its lubricating property is improved by adding some additives such as sulfur, chlorine, phosphorus and molybdenum disulfide. However after cutting with it, washing is required. (Kako, I.)

  9. Nonadiabatic transition path sampling

    International Nuclear Information System (INIS)

    Sherman, M. C.; Corcelli, S. A.

    2016-01-01

    Fewest-switches surface hopping (FSSH) is combined with transition path sampling (TPS) to produce a new method called nonadiabatic path sampling (NAPS). The NAPS method is validated on a model electron transfer system coupled to a Langevin bath. Numerically exact rate constants are computed using the reactive flux (RF) method over a broad range of solvent frictions that span from the energy diffusion (low friction) regime to the spatial diffusion (high friction) regime. The NAPS method is shown to quantitatively reproduce the RF benchmark rate constants over the full range of solvent friction. Integrating FSSH within the TPS framework expands the applicability of both approaches and creates a new method that will be helpful in determining detailed mechanisms for nonadiabatic reactions in the condensed-phase.

  10. PATHS groundwater hydrologic model

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, R.W.; Schur, J.A.

    1980-04-01

    A preliminary evaluation capability for two-dimensional groundwater pollution problems was developed as part of the Transport Modeling Task for the Waste Isolation Safety Assessment Program (WISAP). Our approach was to use the data limitations as a guide in setting the level of modeling detail. PATHS Groundwater Hydrologic Model is the first level (simplest) idealized hybrid analytical/numerical model for two-dimensional, saturated groundwater flow and single component transport; homogeneous geology. This document consists of the description of the PATHS groundwater hydrologic model. The preliminary evaluation capability prepared for WISAP, including the enhancements that were made because of the authors' experience using the earlier capability is described. Appendixes A through D supplement the report as follows: complete derivations of the background equations are provided in Appendix A. Appendix B is a comprehensive set of instructions for users of PATHS. It is written for users who have little or no experience with computers. Appendix C is for the programmer. It contains information on how input parameters are passed between programs in the system. It also contains program listings and test case listing. Appendix D is a definition of terms.

  11. Can You Cut It?

    DEFF Research Database (Denmark)

    Kjær, Tina; Lillelund, Christoffer Bredo; Moth-Poulsen, Mie

    2017-01-01

    The advent of affordable virtual reality (VR) displays and 360◦ video cameras has sparked an interest in bringing cinematic experiences from the screen and into VR. However, it remains uncertain whether traditional approaches to filmmaking can be directly applied to cinematic VR. Historically......’ sense of disorientation and their ability to follow the story, during exposure to fictional 360◦ films experienced using a head-mounted display. The results revealed no effects of increased cut frequency which leads us to conclude that editing need not pose a problem in relation to cinematic VR, as long...

  12. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Stefan Miska; Nicholas Takach; Kaveh Ashenayi

    2004-07-31

    We have tested the loop elevation system. We raised the mast to approximately 25 to 30 degrees from horizontal. All went well. However, while lowering the mast, it moved laterally a couple of degrees. Upon visual inspection, severe spalling of the concrete on the face of the support pillar, and deformation of the steel support structure was observed. At this time, the facility is ready for testing in the horizontal position. A new air compressor has been received and set in place for the ACTS test loop. A new laboratory has been built near the ACTS test loop Roughened cups and rotors for the viscometer (RS300) were obtained. Rheologies of aqueous foams were measured using three different cup-rotor assemblies that have different surface roughness. The relationship between surface roughness and foam rheology was investigated. Re-calibration of nuclear densitometers has been finished. The re-calibration was also performed with 1% surfactant foam. A new cuttings injection system was installed at the bottom of the injection tower. It replaced the previous injection auger. A mechanistic model for cuttings transport with aerated mud has been developed. Cuttings transport mechanisms with aerated water at various conditions were experimentally investigated. A total of 39 tests were performed. Comparisons between the model predictions and experimental measurements show a satisfactory agreement. Results from the ultrasonic monitoring system indicated that we could distinguish between different sand levels. We also have devised ways to achieve consistency of performance by securing the sensors in the caps in exactly the same manner as long as the sensors are not removed from the caps. A preliminary test was conducted on the main flow loop at 100 gpm flow rate and 20 lb/min cuttings injection rate. The measured bed thickness using the ultrasonic method showed a satisfactory agreement with nuclear densitometer readings. Thirty different data points were collected after the test

  13. Cutting the Cord-2

    Science.gov (United States)

    2004-01-01

    This animation shows the view from the rear hazard avoidance cameras on the Mars Exploration Rover Spirit as the rover turns 45 degrees clockwise. This maneuver is the first step in a 3-point turn that will rotate the rover 115 degrees to face west. The rover must make this turn before rolling off the lander because airbags are blocking it from exiting from the front lander petal. Before this crucial turn took place, engineers instructed the rover to cut the final cord linking it to the lander. The turn took around 30 minutes to complete.

  14. Cutting the Cord

    Science.gov (United States)

    2004-01-01

    This animation shows the view from the front hazard avoidance cameras on the Mars Exploration Rover Spirit as the rover turns 45 degrees clockwise. This maneuver is the first step in a 3-point turn that will rotate the rover 115 degrees to face west. The rover must make this turn before rolling off the lander because airbags are blocking it from exiting off the front lander petal. Before this crucial turn could take place, engineers instructed the rover to cut the final cord linking it to the lander. The turn took around 30 minutes to complete.

  15. Leptogenesis: The other cuts

    International Nuclear Information System (INIS)

    Garbrecht, Bjoern

    2011-01-01

    For standard leptogenesis from the decay of singlet right-handed neutrinos, we derive source terms for the lepton asymmetry that are present in a finite density background but absent in the vacuum. These arise from cuts through the vertex correction to the decay asymmetry, where in the loop either the Higgs boson and the right-handed neutrino or the left-handed lepton and the right-handed neutrino are simultaneously on-shell. We evaluate the source terms numerically and use them to calculate the lepton asymmetry for illustrative points in parameter space, where we consider only two right-handed neutrinos for simplicity. Compared to calculations where only the standard cut through the propagators of left-handed lepton and Higgs boson is included, sizable corrections arise when the masses of the right-handed neutrinos are of the same order, but the new sources are found to be most relevant when the decaying right-handed neutrino is heavier than the one in the loop. In that situation, they can yield the dominant contribution to the lepton asymmetry.

  16. CO2 laser cutting

    CERN Document Server

    Powell, John

    1998-01-01

    The laser has given manufacturing industry a new tool. When the laser beam is focused it can generate one of the world's most intense energy sources, more intense than flames and arcs, though similar to an electron beam. In fact the intensity is such that it can vaporise most known materials. The laser material processing industry has been growing swiftly as the quality, speed and new manufacturing possibilities become better understood. In the fore of these new technologies is the process of laser cutting. Laser cutting leads because it is a direct process substitu­ tion and the laser can usually do the job with greater flexibility, speed and quality than its competitors. However, to achieve these high speeds with high quality con­ siderable know how and experience is required. This information is usually carefully guarded by the businesses concerned and has to be gained by hard experience and technical understanding. Yet in this book John Powell explains in lucid and almost non­ technical language many o...

  17. Manipulator motion planning for high-speed robotic laser cutting

    OpenAIRE

    Dolgui , Alexandre; Pashkevich , Anatol

    2009-01-01

    Abstract Recent advances in laser technology, and especially the essential increase of the cutting speed, motivate amending the existing robot path methods, which do not allow the complete utilisation of the actuator capabilities as well as neglect some particularities in the mechanical design of the wrist of the manipulator arm. This research addresses the optimisation of the 6-axes robot motions for continuous contour tracking while considering the redundancy caused by the tool a...

  18. Cutting Temperature Investigation of AISI H13 in High Speed End Milling

    Directory of Open Access Journals (Sweden)

    Muhammad Riza

    2016-10-01

    Full Text Available Heat produced at the tool-chip interface during high speed milling operations have been known as a significant factor that affect to tool life and workpiece geometry or properties. This paper aims to investigate cutting temperature behaviours of AISI H13 (48 HRC under high speed machining circumstances during pocketing. The experiments were conducted on CNC vertical machining centre by using PVD coated carbide insert. Milling processes were done at cutting speeds 150, 200 and 250 m/min and feed rate were 0.05, 0.1 and 0.15 mm/tooth. Depths of cut applied were 0.1, 0.15 and 0.2 mm. Tool path method applied in this experiment was contour in. Results presented in this paper indicate that by increasing cutting speed the cutting temperature is lower than low cutting speed. However, by decreasing feed rate leads to cutting temperature low. Cutting temperature phenomena at the corner of pocket milling were also investigated. The phenomena showed that cutting temperature tends to decrease a moment when cutter comes to the corner of pocket and turning point of tool path and increase extremely a moment before leaving the corner and turning point.

  19. The Cutting Process, Chips and Cutting Forces in Machining CFRP

    DEFF Research Database (Denmark)

    Koplev, A.; Lystrup, Aage; Vorm, T.

    1983-01-01

    The cutting of unidirectional CFRP, perpendicular as well as parallel to the fibre orientation, is examined. Shaping experiments, ‘quick-stop’ experiments, and a new chip preparation technique are used for the investigation. The formation of the chips, and the quality of the machined surface...... is discussed. The cutting forces parallel and perpendicular to the cutting direction are measured for various parameters, and the results correlated to the formation of chips and the wear of the tool....

  20. Aerodynamic Interactions During Laser Cutting

    Science.gov (United States)

    Fieret, J.; Terry, M. J.; Ward, B. A.

    1986-11-01

    Most laser cutting systems utilise a gas jet to remove molten or vaporised material from the kerf. The speed, economy and quality of the cut can be strongly dependent on the aerodynamic conditions created by the nozzle, workpiece proximity and kerf shape. Adverse conditions can be established that may lead to an unwelcome lack of reproducibility of cut quality. Relatively low gas nozzle pressures can result in supersonic flow in the jet with its associated shock fronts. When the nozzle is placed at conventional distances (1-2mm) above the workpiece, the force exerted by the gas on the workpiece and the cut products (the cutting pressure) can be significantly less than the nozzle pressure. Higher cutting pressures can be achieved by increasing the height of the nozzle above the workpiece, to a more damage resistant zone, provided that the shock structure of the jet is taken into account. Conventional conical nozzles with circular exits can be operated with conditions that will result in cutting pressures up to 3 Bar (g) in the more distant zone. At higher pressures in circular tipped nozzles the cutting pressure in this zone decays to inadequate levels. Investigations of a large number of non-circular nozzle tip shapes have resulted in the selection of a few specific shapes that can provide cutting pressures in excess of 6 Bar(g) at distances of 4 to 7mm from the nozzle tip. Since there is a strong correlation between cutting pressure and the speed and quality of laser cutting, the paper describes the aerodynamic requirements for achieving the above effects and reports the cutting results arising from the different nozzle designs and conditions. The results of the work of other investigators, who report anomalous laser cutting results, will be examined and reviewed in the light of the above work.

  1. Rocket Flight Path

    Directory of Open Access Journals (Sweden)

    Jamie Waters

    2014-09-01

    Full Text Available This project uses Newton’s Second Law of Motion, Euler’s method, basic physics, and basic calculus to model the flight path of a rocket. From this, one can find the height and velocity at any point from launch to the maximum altitude, or apogee. This can then be compared to the actual values to see if the method of estimation is a plausible. The rocket used for this project is modeled after Bullistic-1 which was launched by the Society of Aeronautics and Rocketry at the University of South Florida.

  2. JAVA PathFinder

    Science.gov (United States)

    Mehhtz, Peter

    2005-01-01

    JPF is an explicit state software model checker for Java bytecode. Today, JPF is a swiss army knife for all sort of runtime based verification purposes. This basically means JPF is a Java virtual machine that executes your program not just once (like a normal VM), but theoretically in all possible ways, checking for property violations like deadlocks or unhandled exceptions along all potential execution paths. If it finds an error, JPF reports the whole execution that leads to it. Unlike a normal debugger, JPF keeps track of every step how it got to the defect.

  3. Hamiltonian path integrals

    International Nuclear Information System (INIS)

    Prokhorov, L.V.

    1982-01-01

    Problems related to consideration of operator nonpermutability in Hamiltonian path integral (HPI) are considered in the review. Integrals are investigated using trajectories in configuration space (nonrelativistic quantum mechanics). Problems related to trajectory integrals in HPI phase space are discussed: the problem of operator nonpermutability consideration (extra terms problem) and corresponding equivalence rules; ambiguity of HPI usual recording; transition to curvilinear coordinates. Problem of quantization of dynamical systems with couplings has been studied. As in the case of canonical transformations, quantization of the systems with couplings of the first kind requires the consideration of extra terms

  4. Path to Prosperity

    OpenAIRE

    Wolfowitz,Paul

    2006-01-01

    Paul Wolfowitz, President of the World Bank, discussed Singapore's remarkable progress along the road from poverty to prosperity which has also been discovered by many other countries in East Asia and around the world. He spoke of how each country must find its own path for people to pursue the same dreams of the chance to go to school, the security of a good job, and the ability to provide a better future for their children. Throughout the world, and importantly in the developing world, ther...

  5. ADVANCED CUTTINGS TRANSPORT STUDY

    Energy Technology Data Exchange (ETDEWEB)

    Stefan Miska; Nicholas Takach; Kaveh Ashenayi

    2004-01-31

    Final design of the mast was completed (Task 5). The mast is consisting of two welded plate girders, set next to each other, and spaced 14-inches apart. Fabrication of the boom will be completed in two parts solely for ease of transportation. The end pivot connection will be made through a single 2-inch diameter x 4 feet-8 inch long 316 SS bar. During installation, hard piping make-ups using Chiksan joints will connect the annular section and 4-inch return line to allow full movement of the mast from horizontal to vertical. Additionally, flexible hoses and piping will be installed to isolate both towers from piping loads and allow recycling operations respectively. Calibration of the prototype Foam Generator Cell has been completed and experiments are now being conducted. We were able to generate up to 95% quality foam. Work is currently underway to attach the Thermo-Haake RS300 viscometer and install a view port with a microscope to measure foam bubble size and bubble size distribution. Foam rheology tests (Task 13) were carried out to evaluate the rheological properties of the proposed foam formulation. After successful completion of the first foam test, two sets of rheological tests were conducted at different foam flow rates while keeping other parameters constant (100 psig, 70F, 80% quality). The results from these tests are generally in agreement with the previous foam tests done previously during Task 9. However, an unanticipated observation during these tests was that in both cases, the frictional pressure drop in 2 inch pipe was lower than that in the 3 inch and 4 inch pipes. We also conducted the first foam cuttings transport test during this quarter. Experiments on aerated fluids without cuttings have been completed in ACTF (Task 10). Gas and liquid were injected at different flow rates. Two different sets of experiments were carried out, where the only difference was the temperature. Another set of tests was performed, which covered a wide range of

  6. Skin Cut Construction

    DEFF Research Database (Denmark)

    2017-01-01

    projects - among others - from ARC are included: Soft Structures builds upon of a series of experimental use of EPS hot wire cutting, where the EPS eventually act as formwork for concrete casting. The processing of the EPS is distinct and delimited by the behaviour and form of both the robot and tool...... of steel and concrete makes it a reliable approach to many challenges in the realisation of buildings. Rebar Inside Out attempts to rethink the possibilities of the reinforced concrete composite starting from its inside. This means starting with the reinforcing steel, the production and shaping of this......, and then through that process build a workflow for the production of the concrete composite. It also means letting the steel out of the concrete, thereby positioning the two materials in a transnational relationship between steel construction and concrete composite....

  7. World nuclear energy paths

    International Nuclear Information System (INIS)

    Connolly, T.J.; Hansen, U.; Jaek, W.; Beckurts, K.H.

    1979-01-01

    In examing the world nuclear energy paths, the following assumptions were adopted: the world economy will grow somewhat more slowly than in the past, leading to reductions in electricity demand growth rates; national and international political impediments to the deployment of nuclear power will gradually disappear over the next few years; further development of nuclear power will proceed steadily, without serious interruption but with realistic lead times for the introduction of advanced technologies. Given these assumptions, this paper attempts a study of possible world nuclear energy developments, disaggregated on a regional and national basis. The scenario technique was used and a few alternative fuel-cycle scenarios were developed. Each is an internally consistent model of technically and economically feasible paths to the further development of nuclear power in an aggregate of individual countries and regions of the world. The main purpose of this modeling exercise was to gain some insight into the probable international locations of reactors and other nuclear facilities, the future requirements for uranium and for fuel-cycle services, and the problems of spent-fuel storage and waste management. The study also presents an assessment of the role that nuclear power might actually play in meeting future world energy demand

  8. Semantic Versus Syntactic Cutting Planes

    OpenAIRE

    Filmus, Yuval; Hrubeš, Pavel; Lauria, Massimo

    2016-01-01

    In this paper, we compare the strength of the semantic and syntactic version of the cutting planes proof system. First, we show that the lower bound technique of Pudlák applies also to semantic cutting planes: the proof system has feasible interpolation via monotone real circuits, which gives an exponential lower bound on lengths of semantic cutting planes refutations. Second, we show that semantic refutations are stronger than syntactic ones. In particular, we give a formula for whic...

  9. Laser Cutting of Different Materials

    Directory of Open Access Journals (Sweden)

    Kadir ÇAVDAR

    2013-08-01

    Full Text Available In this paper; in general potential developments and trends of a particular machining field by extensively evaluating present studies of laser beam machining have been discussed. As it is indicated below, technical literatures have been subsumed under five major headlines: Experimental studies, reviews, optimization researches of the cutting parameters, theoretical modelling studies of laser beam cutting and academic studies relating to laser cutting

  10. Latest development of laser cutting

    OpenAIRE

    Wetzig, Andreas; Herwig, Patrick; Hauptmann, Jan; Goppold, Cindy; Baumann, Robert; Fürst, Andreas; Rose, Michael; Pinder, Thomas; Mahrle, Achim; Beyer, Eckhard

    2016-01-01

    Laser cutting was one of the first applications of laser material processing. Today, laser cutting is the most widespread application among laser material processing besides laser marking. Meanwhile, nearly each material can be cut by means of a laser, in particular since ultra short pulse lasers are available in the power range of up to 100 W. The to be cut material can come with thicknesses from a few microns till tens of millimeters as flat stock or as free form shapes. The paper will conc...

  11. CALCULATION OF LASER CUTTING COSTS

    Directory of Open Access Journals (Sweden)

    Bogdan Nedic

    2016-09-01

    Full Text Available The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, comparison' of costs made by other unconventional methods and provides documentation that consists of reports on estimated costs.

  12. Active Path Planning for Drones in Object Search

    OpenAIRE

    Wang, Zeyangyi

    2017-01-01

    Object searching is one of the most popular applications of unmanned aerial vehicles. Low cost small drones are particularly suited for surveying tasks in difficult conditions. With their limited on-board processing power and battery life, there is a need for more efficient search algorithm. The proposed path planning algorithm utilizes AZ-net, a deep learning network to process images captured on drones for adaptive flight path planning. Search simulation based on videos and actual experimen...

  13. Local drying underwater cutting of reactor core internals by CO laser

    International Nuclear Information System (INIS)

    Beppu, Seiji; Takano, Genta; Matsumoto, Osa; Sugihara, Masaaki; Miya, Kenzo.

    1991-01-01

    Since the CO laser operates at shorter wavelength than the CO 2 laser, the former has superior ability to cut materials. Its applicability to the cutting of reactor core internals in a nuclear power plant has been studied. In order to use such a laser for cutting actual structures, it would be useful to develop underwater cutting technology for the purpose of minimizing radiation exposure during cutting. However, since the laser beam is absorbed by water, a path needs to be cleared along the laser's line of sight. The authors have developed a nozzle that forms a local dry zone and have demonstrated that CO laser cutting can be carried out under water as it is in air. (author)

  14. Decision paths in complex tasks

    Science.gov (United States)

    Galanter, Eugene

    1991-01-01

    Complex real world action and its prediction and control has escaped analysis by the classical methods of psychological research. The reason is that psychologists have no procedures to parse complex tasks into their constituents. Where such a division can be made, based say on expert judgment, there is no natural scale to measure the positive or negative values of the components. Even if we could assign numbers to task parts, we lack rules i.e., a theory, to combine them into a total task representation. We compare here two plausible theories for the amalgamation of the value of task components. Both of these theories require a numerical representation of motivation, for motivation is the primary variable that guides choice and action in well-learned tasks. We address this problem of motivational quantification and performance prediction by developing psychophysical scales of the desireability or aversiveness of task components based on utility scaling methods (Galanter 1990). We modify methods used originally to scale sensory magnitudes (Stevens and Galanter 1957), and that have been applied recently to the measure of task 'workload' by Gopher and Braune (1984). Our modification uses utility comparison scaling techniques which avoid the unnecessary assumptions made by Gopher and Braune. Formula for the utility of complex tasks based on the theoretical models are used to predict decision and choice of alternate paths to the same goal.

  15. Paths of Cultural Systems

    Directory of Open Access Journals (Sweden)

    Paul Ballonoff

    2017-12-01

    Full Text Available A theory of cultural structures predicts the objects observed by anthropologists. We here define those which use kinship relationships to define systems. A finite structure we call a partially defined quasigroup (or pdq, as stated by Definition 1 below on a dictionary (called a natural language allows prediction of certain anthropological descriptions, using homomorphisms of pdqs onto finite groups. A viable history (defined using pdqs states how an individual in a population following such history may perform culturally allowed associations, which allows a viable history to continue to survive. The vector states on sets of viable histories identify demographic observables on descent sequences. Paths of vector states on sets of viable histories may determine which histories can exist empirically.

  16. Propagators and path integrals

    Energy Technology Data Exchange (ETDEWEB)

    Holten, J.W. van

    1995-08-22

    Path-integral expressions for one-particle propagators in scalar and fermionic field theories are derived, for arbitrary mass. This establishes a direct connection between field theory and specific classical point-particle models. The role of world-line reparametrization invariance of the classical action and the implementation of the corresponding BRST-symmetry in the quantum theory are discussed. The presence of classical world-line supersymmetry is shown to lead to an unwanted doubling of states for massive spin-1/2 particles. The origin of this phenomenon is traced to a `hidden` topological fermionic excitation. A different formulation of the pseudo-classical mechanics using a bosonic representation of {gamma}{sub 5} is shown to remove these extra states at the expense of losing manifest supersymmetry. (orig.).

  17. innovation path exploration

    Directory of Open Access Journals (Sweden)

    Li Jian

    2016-01-01

    Full Text Available The world has entered the information age, all kinds of information technologies such as cloud technology, big data technology are in rapid development, and the “Internet plus” appeared. The main purpose of “Internet plus” is to provide an opportunity for the further development of the enterprise, the enterprise technology, business and other aspects of factors combine. For enterprises, grasp the “Internet plus” the impact of the market economy will undoubtedly pave the way for the future development of enterprises. This paper will be on the innovation path of the enterprise management “Internet plus” era tied you study, hope to be able to put forward some opinions and suggestions.

  18. A cutting fluid

    Energy Technology Data Exchange (ETDEWEB)

    Kajdas, C.; Dominiak, M.; Kozinski, R.; Misterkiewicz, B.; Polowniak, J.; Szczepaniak, S.

    1982-06-30

    The cutting fluid (SOZh) contains 0.5 to 10 percent vegetable or animal fats, selectively sulfurized in the presence of a catalyst (Kt): 0.1 to 10 percent chlorinated C2O to C3O paraffins, which contain 10 to 50 percent Chlorine in a molecule, and 0.001 to 0.5 percent dialkyldithiocarbamic or alkylen-bis-(dithiocarbamic) acids or their salts or derivatives of the form (R(R')NC(S)SRn'', (CH2)n(NHC(S)S)2R'' or R(R')NC(S)SnC(S)(R)R', where R and R' are alkyl or cycloalkyl of the C1 to C6 fractions, R'' is Hydrogen, a metal, or aliphatic or heterocyclic amine, n = 2 to 6 and 0.001 to 0.3 percent of heterocyclic mercaptanes or disulfides of the cited formula, where A is Nitrogen or Sulfur, and up to 100 percent petroleum oil with a kinematic viscosity of 5 to 50 square millimeters per second at 323K.

  19. Differential neural network configuration during human path integration

    Science.gov (United States)

    Arnold, Aiden E. G. F; Burles, Ford; Bray, Signe; Levy, Richard M.; Iaria, Giuseppe

    2014-01-01

    Path integration is a fundamental skill for navigation in both humans and animals. Despite recent advances in unraveling the neural basis of path integration in animal models, relatively little is known about how path integration operates at a neural level in humans. Previous attempts to characterize the neural mechanisms used by humans to visually path integrate have suggested a central role of the hippocampus in allowing accurate performance, broadly resembling results from animal data. However, in recent years both the central role of the hippocampus and the perspective that animals and humans share similar neural mechanisms for path integration has come into question. The present study uses a data driven analysis to investigate the neural systems engaged during visual path integration in humans, allowing for an unbiased estimate of neural activity across the entire brain. Our results suggest that humans employ common task control, attention and spatial working memory systems across a frontoparietal network during path integration. However, individuals differed in how these systems are configured into functional networks. High performing individuals were found to more broadly express spatial working memory systems in prefrontal cortex, while low performing individuals engaged an allocentric memory system based primarily in the medial occipito-temporal region. These findings suggest that visual path integration in humans over short distances can operate through a spatial working memory system engaging primarily the prefrontal cortex and that the differential configuration of memory systems recruited by task control networks may help explain individual biases in spatial learning strategies. PMID:24808849

  20. The Gesso Cut for Printmaking

    Science.gov (United States)

    Kelly, Perry; Sarvis, Alva

    1969-01-01

    Directions are given for the preparation, cutting, and printing of a gesso board. A gesso cut is defined as a board coated with gesso into which a design has been impressed. The process is similar to the woodcut, but offers greater textural possibilities. (BF)

  1. Shearer drums - the cutting edge

    Energy Technology Data Exchange (ETDEWEB)

    O' Neill, M.; Wright, C.

    2004-09-15

    The paper discusses continuous miner and shearer cutters. It claims cutting drum require the same level of engineering know-how and technical expertise as do the machines driving them, and that the cutting drum, whether on a longwall shearer or continuous miner, comprises, the steel, pedestals, bit holders and the bits.

  2. Water-Cut Sensor System

    KAUST Repository

    Karimi, Muhammad Akram; Shamim, Atif; Arsalan, Muhammad

    2018-01-01

    Provided in some embodiments is a method of manufacturing a pipe conformable water-cut sensors system. Provided in some embodiments is method for manufacturing a water-cut sensor system that includes providing a helical T-resonator, a helical ground

  3. A German research project about applicable graphite cutting techniques

    International Nuclear Information System (INIS)

    Holland, D.; Quade, U.; Bach, F.W.; Wilk, P.

    2001-01-01

    In Germany, too, quite large quantities of irradiated nuclear graphite, used in research and prototype reactors, are waiting for an environmental way of disposal. While incineration of nuclear graphite does not seem to be a publicly acceptable way, cutting and packaging into ductile cast iron containers could be a suitable way of disposal in Germany. Nevertheless, the cutting of graphite is also a very difficult technique by which a large amount of secondary waste or dust might occur. An applicable graphite cutting technique is needed. Therefore, a group of 13 German partners, consisting of one university, six research reactor operators, one technical inspection authority, three engineering companies, one industrial cutting specialist and one commercial dismantling company, decided in 1999 to start a research project to develop an applicable technique for cutting irradiated nuclear graphite. Aim of the project is to find the most suitable cutting techniques for the existing shapes of graphite blocks with a minimum of waste production rate. At the same time it will be learned how to sample the dust and collect it in a filter system. The following techniques will be tested and evaluated: thermal cutting, water jet cutting, mechanical cutting with a saw, plasma arc cutting, drilling. The subsequent evaluation will concentrate on dust production, possible irradiation of staff, time and practicability under different constraints. This research project is funded by the German Minister of Education and Research under the number 02 S 7849 for a period of two years. A brief overview about the work to be carried out in the project will be given. (author)

  4. Path-finding in real and simulated rats

    DEFF Research Database (Denmark)

    Tamosiunaite, Minija; Ainge, James; Kulvicius, Tomas

    2008-01-01

    without affecting the path characteristic two additional mechanisms are implemented: a gradual drop of the learned weights (weight decay) and path length limitation, which prevents learning if the reward is not found after some expected time. Both mechanisms limit the memory of the system and thereby......A large body of experimental evidence suggests that the hippocampal place field system is involved in reward based navigation learning in rodents. Reinforcement learning (RL) mechanisms have been used to model this, associating the state space in an RL-algorithm to the place-field map in a rat...... convergence of RL-algorithms is also influenced by the state space characteristics, different PF-sizes and densities, leading to a different degree of overlap, were also investigated. The model rat learns finding a reward opposite to its starting point. We observed that the combination of biased straight...

  5. Path integral in Snyder space

    Energy Technology Data Exchange (ETDEWEB)

    Mignemi, S., E-mail: smignemi@unica.it [Dipartimento di Matematica e Informatica, Università di Cagliari, Viale Merello 92, 09123 Cagliari (Italy); INFN, Sezione di Cagliari, Cittadella Universitaria, 09042 Monserrato (Italy); Štrajn, R. [Dipartimento di Matematica e Informatica, Università di Cagliari, Viale Merello 92, 09123 Cagliari (Italy); INFN, Sezione di Cagliari, Cittadella Universitaria, 09042 Monserrato (Italy)

    2016-04-29

    The definition of path integrals in one- and two-dimensional Snyder space is discussed in detail both in the traditional setting and in the first-order formalism of Faddeev and Jackiw. - Highlights: • The definition of the path integral in Snyder space is discussed using phase space methods. • The same result is obtained in the first-order formalism of Faddeev and Jackiw. • The path integral formulation of the two-dimensional Snyder harmonic oscillator is outlined.

  6. Path integral in Snyder space

    International Nuclear Information System (INIS)

    Mignemi, S.; Štrajn, R.

    2016-01-01

    The definition of path integrals in one- and two-dimensional Snyder space is discussed in detail both in the traditional setting and in the first-order formalism of Faddeev and Jackiw. - Highlights: • The definition of the path integral in Snyder space is discussed using phase space methods. • The same result is obtained in the first-order formalism of Faddeev and Jackiw. • The path integral formulation of the two-dimensional Snyder harmonic oscillator is outlined.

  7. Tubing and cable cutting tool

    Science.gov (United States)

    Mcsmith, D. D.; Richardson, J. I. (Inventor)

    1984-01-01

    A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

  8. Cutting method and device underwater

    International Nuclear Information System (INIS)

    Takano, Genta; Kamei, Hiromasa; Beppu, Seiji

    1998-01-01

    A place of material to be cut is surrounded by an openable/closable box. The material to be cut is cut underwater, and materials generated in this case are removed from the cut portion by a pressurized water jet. The removed materials are sucked and recovered together with water in the box. Among the materials caused by the cutting underwater, solid materials not floating on water are caused to stay in the midway of a sucking and recovering channel. A large sucking force might be required for the entire region of the sucking and recovering channel when sucking and recovering large sized solid materials not floating on water, but even large sized materials can be recovered easily according to the present invention since they are recovered after being sucked and stayed in the midway of the sucking and recovering channel. (N.H.)

  9. Cutting concrete with abrasion jet

    International Nuclear Information System (INIS)

    Yie, G.G.

    1982-01-01

    Fluidyne Corporation has developed a unique process and apparatus that allow selected abrasives to be introduced into high-speed waterjet to produce abrasive-entrained waterjet that has high material-cutting capabilities, which is termed by Fluidyne as the Abrasion Jet. Such Abrasion Jet has demonstrated capability in cutting hard rock and concrete at a modest pressure of less than 1360 bars (20,000 psi) and a power input of less than 45 kW (60 horsepower). Abrasion Jet cutting of concrete is characterized by its high rate of cutting, flexible operation, good cut quality, and relatively low costs. This paper presents a general description of this technology together with discussions of recent test results and how it could be applied to nuclear decontamination and decommissioning work. 8 references

  10. Multidimensional Brain MRI segmentation using graph cuts

    International Nuclear Information System (INIS)

    Lecoeur, Jeremy

    2010-01-01

    This thesis deals with the segmentation of multimodal brain MRIs by graph cuts method. First, we propose a method that utilizes three MRI modalities by merging them. The border information given by the spectral gradient is then challenged by a region information, given by the seeds selected by the user, using a graph cut algorithm. Then, we propose three enhancements of this method. The first consists in finding an optimal spectral space because the spectral gradient is based on natural images and then inadequate for multimodal medical images. This results in a learning based segmentation method. We then explore the automation of the graph cut method. Here, the various pieces of information usually given by the user are inferred from a robust expectation-maximization algorithm. We show the performance of these two enhanced versions on multiple sclerosis lesions. Finally, we integrate atlases for the automatic segmentation of deep brain structures. These three new techniques show the adaptability of our method to various problems. Our different segmentation methods are better than most of nowadays techniques, speaking of computation time or segmentation accuracy. (authors)

  11. Cut Based Method for Comparing Complex Networks.

    Science.gov (United States)

    Liu, Qun; Dong, Zhishan; Wang, En

    2018-03-23

    Revealing the underlying similarity of various complex networks has become both a popular and interdisciplinary topic, with a plethora of relevant application domains. The essence of the similarity here is that network features of the same network type are highly similar, while the features of different kinds of networks present low similarity. In this paper, we introduce and explore a new method for comparing various complex networks based on the cut distance. We show correspondence between the cut distance and the similarity of two networks. This correspondence allows us to consider a broad range of complex networks and explicitly compare various networks with high accuracy. Various machine learning technologies such as genetic algorithms, nearest neighbor classification, and model selection are employed during the comparison process. Our cut method is shown to be suited for comparisons of undirected networks and directed networks, as well as weighted networks. In the model selection process, the results demonstrate that our approach outperforms other state-of-the-art methods with respect to accuracy.

  12. Regge cuts in inclusive reactions

    International Nuclear Information System (INIS)

    Paige, F.E.; Trueman, T.L.

    1975-01-01

    The contribution of Regge cuts to single-particle inclusive processes is analyzed using the techniques of Gribov. The dependence of these contributions on the polarization state of the target is emphasized. A general formula is obtained and certain contributions to it are calculated. It is not possible, however, to reduce this to a simple, powerful formula expressing the total cut contribution in terms of other measurable quantities, as can be done for the cut contribution to the total cross section. The reasons for this are discussed in detail. The single-particle intermediate states, analogous to the absorption model for elastic scattering, are explicitly calculated as an illustration

  13. Laser cutting of Kevlar laminates

    Energy Technology Data Exchange (ETDEWEB)

    VanCleave, R.A.

    1977-09-01

    An investigation has been conducted of the use of laser energy for cutting contours, diameters, and holes in flat and shaped Kevlar 49 fiber-reinforced epoxy laminates as an alternate to conventional machining. The investigation has shown that flat laminates 6.35 mm thick may be cut without backup by using a high-powered (1000-watt) continuous wave CO/sub 2/ laser at high feedrates (33.87 mm per second). The cut produced was free of the burrs and delaminations resulting from conventional machining methods without intimate contact backup. In addition, the process cycle time was greatly reduced.

  14. Preferences of cut flowers consumers

    Directory of Open Access Journals (Sweden)

    Sylwia Kierczyńska

    2010-01-01

    Full Text Available The results of interviews suggest that majority of the cut flowers’ consumers has favourite kind of flower, among which most frequently pointed one was the rose. More than half of the interviewed favour the uniform colour of cut flowers and red colour was the most favourite one. The subtle smell of flowers was the most preferable one but the intensive fragrance was favoured for more consumers than odourless flowers. The data from selected florists’ confirm the information from interviews – in spite of the occasion, roses were the most demanded cut flowers.

  15. Two Generations of Path Dependence

    DEFF Research Database (Denmark)

    Madsen, Mogens Ove

      Even if there is no fully articulated and generally accepted theory of Path Dependence it has eagerly been taken up across a wide range of social sciences - primarily coming from economics. Path Dependence is most of all a metaphor that offers reason to believe, that some political, social...

  16. Chromatic roots and hamiltonian paths

    DEFF Research Database (Denmark)

    Thomassen, Carsten

    2000-01-01

    We present a new connection between colorings and hamiltonian paths: If the chromatic polynomial of a graph has a noninteger root less than or equal to t(n) = 2/3 + 1/3 (3)root (26 + 6 root (33)) + 1/3 (3)root (26 - 6 root (33)) = 1.29559.... then the graph has no hamiltonian path. This result...

  17. On Hilbert space of paths

    International Nuclear Information System (INIS)

    Exner, P.; Kolerov, G.I.

    1980-01-01

    A Hilbert space of paths, the elements of which are determined by trigonometric series, was proposed and used recently by Truman. This space is shown to consist precisely of all absolutely continuous paths ending in the origin with square-integrable derivatives

  18. Hard paths, soft paths or no paths? Cross-cultural perceptions of water solutions

    Science.gov (United States)

    Wutich, A.; White, A. C.; White, D. D.; Larson, K. L.; Brewis, A.; Roberts, C.

    2014-01-01

    In this study, we examine how development status and water scarcity shape people's perceptions of "hard path" and "soft path" water solutions. Based on ethnographic research conducted in four semi-rural/peri-urban sites (in Bolivia, Fiji, New Zealand, and the US), we use content analysis to conduct statistical and thematic comparisons of interview data. Our results indicate clear differences associated with development status and, to a lesser extent, water scarcity. People in the two less developed sites were more likely to suggest hard path solutions, less likely to suggest soft path solutions, and more likely to see no path to solutions than people in the more developed sites. Thematically, people in the two less developed sites envisioned solutions that involve small-scale water infrastructure and decentralized, community-based solutions, while people in the more developed sites envisioned solutions that involve large-scale infrastructure and centralized, regulatory water solutions. People in the two water-scarce sites were less likely to suggest soft path solutions and more likely to see no path to solutions (but no more likely to suggest hard path solutions) than people in the water-rich sites. Thematically, people in the two water-rich sites seemed to perceive a wider array of unrealized potential soft path solutions than those in the water-scarce sites. On balance, our findings are encouraging in that they indicate that people are receptive to soft path solutions in a range of sites, even those with limited financial or water resources. Our research points to the need for more studies that investigate the social feasibility of soft path water solutions, particularly in sites with significant financial and natural resource constraints.

  19. Road networks as collections of minimum cost paths

    Science.gov (United States)

    Wegner, Jan Dirk; Montoya-Zegarra, Javier Alexander; Schindler, Konrad

    2015-10-01

    We present a probabilistic representation of network structures in images. Our target application is the extraction of urban roads from aerial images. Roads appear as thin, elongated, partially curved structures forming a loopy graph, and this complex layout requires a prior that goes beyond standard smoothness and co-occurrence assumptions. In the proposed model the network is represented as a union of 1D paths connecting distant (super-)pixels. A large set of putative candidate paths is constructed in such a way that they include the true network as much as possible, by searching for minimum cost paths in the foreground (road) likelihood. Selecting the optimal subset of candidate paths is posed as MAP inference in a higher-order conditional random field. Each path forms a higher-order clique with a type of clique potential, which attracts the member nodes of cliques with high cumulative road evidence to the foreground label. That formulation induces a robust PN -Potts model, for which a global MAP solution can be found efficiently with graph cuts. Experiments with two road data sets show that the proposed model significantly improves per-pixel accuracies as well as the overall topological network quality with respect to several baselines.

  20. Regge cuts: A general approach

    International Nuclear Information System (INIS)

    Weis, J.H.

    1976-01-01

    We discuss an approach to the calculation of Regge-cut contributions to scattering amplitudes which relies only on the general structure of the physical Reggeon couplings. It thus allows a unified treatment of disparate models [such as the Feynman (Mandelstam) graph model and the dual model] and a general derivation of the Abramovskii--Gribov--Kancheli (AGK) rules. The structure of the Reggeon couplings is expressed through integrals over complex helicity. The Regge-cut amplitude can then be obtained, and its s-channel discontinuity, taken; there results a direct derivation of a set of ''cutting rules'' which express the total discontinuity as a sum of terms involving various discontinuities of the Reggeon couplings. The equality of these discontinuities follows directly if the singularities in complex helicity are the usual ones. Thus the AGK rules are seen to be quite model independent. Here we study in detail the simplest example: the Reggeon-particle cut in the four-particle amplitude

  1. Materials selection for cutting tools

    International Nuclear Information System (INIS)

    Burkhis, Adel M.

    2008-01-01

    The selection of proper tool steel for a given application is a difficult task. So; the most important selection factors in choosing cutting tool materials are based on their tool material requirements, cutting tool design and service conditions which is mainly considered as functional requirements. The processability requirements concerns in heat treat ability of the material tool. The classification of these tool materials were discussed with their properties requirement and percent of alloying element which is added to give best properties with a little increase in cost that highly appear in comparison of the selection. The cutting tool materials were evaluated based on two cases; The first was in case of rough surface; the high speed steels is the best material and the other was the ceramic material is the highest performance in cutting of soft or high rate of metal removal. (author)

  2. Laser cutting: industrial relevance, process optimization, and laser safety

    Science.gov (United States)

    Haferkamp, Heinz; Goede, Martin; von Busse, Alexander; Thuerk, Oliver

    1998-09-01

    Compared to other technological relevant laser machining processes, up to now laser cutting is the application most frequently used. With respect to the large amount of possible fields of application and the variety of different materials that can be machined, this technology has reached a stable position within the world market of material processing. Reachable machining quality for laser beam cutting is influenced by various laser and process parameters. Process integrated quality techniques have to be applied to ensure high-quality products and a cost effective use of the laser manufacturing plant. Therefore, rugged and versatile online process monitoring techniques at an affordable price would be desirable. Methods for the characterization of single plant components (e.g. laser source and optical path) have to be substituted by an omnivalent control system, capable of process data acquisition and analysis as well as the automatic adaptation of machining and laser parameters to changes in process and ambient conditions. At the Laser Zentrum Hannover eV, locally highly resolved thermographic measurements of the temperature distribution within the processing zone using cost effective measuring devices are performed. Characteristic values for cutting quality and plunge control as well as for the optimization of the surface roughness at the cutting edges can be deducted from the spatial distribution of the temperature field and the measured temperature gradients. Main influencing parameters on the temperature characteristic within the cutting zone are the laser beam intensity and pulse duration in pulse operation mode. For continuous operation mode, the temperature distribution is mainly determined by the laser output power related to the cutting velocity. With higher cutting velocities temperatures at the cutting front increase, reaching their maximum at the optimum cutting velocity. Here absorption of the incident laser radiation is drastically increased due to

  3. Economic technology of laser cutting

    Science.gov (United States)

    Fedin, Alexander V.; Shilov, Igor V.; Vassiliev, Vladimir V.; Malov, Dmitri V.; Peskov, Vladimir N.

    2000-02-01

    The laser cutting of color metals and alloys by a thickness more than 2 mm has significant difficulties due to high reflective ability and large thermal conduction. We made it possible to raise energy efficiency and quality of laser cutting by using a laser processing system (LPS) consisting both of the YAG:Nd laser with passive Q-switching on base of LiF:F2- crystals and the CO2 laser. A distinctive feature of the LPS is that the radiation of different lasers incorporated in a coaxial beam has simultaneously high level of peak power (more than 400 kW in a TEM00 mode) and significant level of average power (up to 800 W in a TEM01 mode of the CO2 laser). The application of combined radiation for cutting of an aluminum alloy of D16 type made it possible to decrease the cutting energy threshold in 1.7 times, to increase depth of treatment from 2 up to 4 mm, and velocity from 0.015 up to 0.7 m/min, and also to eliminate application of absorptive coatings. At cutting of steels the velocity of treatment was doubled, and also an oxygen flow was eliminated from the technological process and replaced by the air. The obtained raise of energy efficiency and quality of cutting is explained by an essential size reducing of a formed penetration channel and by the shifting of a thermal cutting mode from melting to evaporation. The evaluation of interaction efficiency of a combined radiation was produced on the basis of non-stationary thermal-hydrodynamic model of a heating source moving as in the cutting direction, and also into the depth of material.

  4. The potential of laser cutting and snake arm robots in aspects of nuclear decommissioning

    International Nuclear Information System (INIS)

    Hilton, Paul; Khan, Ali

    2013-01-01

    This paper will describe recent work conducted in the UK to highlight the potential of applying high power laser cutting to aspects of decommissioning and dismantling in the nuclear sector. A major driver for this activity is size reduction of metallic structures, vessels and tubing, with the objective of efficient stacking of the cut parts for future long term storage. TWI have used a standard 5 kW multi-mode laser with fibre optic delivery of the beam, to demonstrate techniques for cutting stainless steel tubing, at diameters up to 150 mm and wall thicknesses up to 7 mm, and various thicknesses of plate materials. Using specially developed cutting heads, employing long focal length lenses to form the beam, techniques were developed to allow the cutting of tubes from one side only and without changing the focal position of the laser beam with respect to the diameter of the tube perpendicular to the incident beam. The latter means that remote programming of the cutting path becomes much simpler. For cutting plate materials, special gas nozzle dynamics have produced great tolerance of the cutting process to stand-off distance (the distance between the surface of the material being cut and the exit of the cutting nozzle). One particularly interesting method of remote deployment of these cutting techniques is to use 'snake arm' robots. These robots, by nature of their construction, can access areas un-accessible using other techniques. This of course makes them particularly suited to aspects of nuclear decommissioning, particularly in what are termed 'un-structured environments', where the exact disposition of items encountered is not known. The paper will also describe the first time a laser cutting head has been installed on the end of a snake arm robot and the combination used in a simulated nuclear cutting application. (author)

  5. Optimal Paths in Gliding Flight

    Science.gov (United States)

    Wolek, Artur

    Underwater gliders are robust and long endurance ocean sampling platforms that are increasingly being deployed in coastal regions. This new environment is characterized by shallow waters and significant currents that can challenge the mobility of these efficient (but traditionally slow moving) vehicles. This dissertation aims to improve the performance of shallow water underwater gliders through path planning. The path planning problem is formulated for a dynamic particle (or "kinematic car") model. The objective is to identify the path which satisfies specified boundary conditions and minimizes a particular cost. Several cost functions are considered. The problem is addressed using optimal control theory. The length scales of interest for path planning are within a few turn radii. First, an approach is developed for planning minimum-time paths, for a fixed speed glider, that are sub-optimal but are guaranteed to be feasible in the presence of unknown time-varying currents. Next the minimum-time problem for a glider with speed controls, that may vary between the stall speed and the maximum speed, is solved. Last, optimal paths that minimize change in depth (equivalently, maximize range) are investigated. Recognizing that path planning alone cannot overcome all of the challenges associated with significant currents and shallow waters, the design of a novel underwater glider with improved capabilities is explored. A glider with a pneumatic buoyancy engine (allowing large, rapid buoyancy changes) and a cylindrical moving mass mechanism (generating large pitch and roll moments) is designed, manufactured, and tested to demonstrate potential improvements in speed and maneuverability.

  6. Twice cutting method reduces tibial cutting error in unicompartmental knee arthroplasty.

    Science.gov (United States)

    Inui, Hiroshi; Taketomi, Shuji; Yamagami, Ryota; Sanada, Takaki; Tanaka, Sakae

    2016-01-01

    Bone cutting error can be one of the causes of malalignment in unicompartmental knee arthroplasty (UKA). The amount of cutting error in total knee arthroplasty has been reported. However, none have investigated cutting error in UKA. The purpose of this study was to reveal the amount of cutting error in UKA when open cutting guide was used and clarify whether cutting the tibia horizontally twice using the same cutting guide reduced the cutting errors in UKA. We measured the alignment of the tibial cutting guides, the first-cut cutting surfaces and the second cut cutting surfaces using the navigation system in 50 UKAs. Cutting error was defined as the angular difference between the cutting guide and cutting surface. The mean absolute first-cut cutting error was 1.9° (1.1° varus) in the coronal plane and 1.1° (0.6° anterior slope) in the sagittal plane, whereas the mean absolute second-cut cutting error was 1.1° (0.6° varus) in the coronal plane and 1.1° (0.4° anterior slope) in the sagittal plane. Cutting the tibia horizontally twice reduced the cutting errors in the coronal plane significantly (Pcutting the tibia horizontally twice using the same cutting guide reduced cutting error in the coronal plane. Copyright © 2014 Elsevier B.V. All rights reserved.

  7. High power YAG laser cutting; Koshutsuryoku YAG laser ni yoru setsudan gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Owaki, K. [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1998-08-01

    This paper describes features of high power YAG cutting. The optical fiber transmission YAG laser machining system has some advantages in which optical path length compensation unit is not required and measures for low power loss and dust are not required, when compared with the CO2 laser system. Its application to the cutting of stainless steel plates has attracted attention. Cutting tests of SUS304 were conducted using high power YAG laser. Cutting of SUS304 plate with a thickness of 40 mm could be successfully done at the power of 3.5 kW. Cutting tests of SUS304 pipes with a thickness of 8 mm in water under the depth of 20 m were also conducted using air as assist gas at the power of 2.5 kW. Excellent results were obtained without scale deposition. For the tests by the composite beam using 3 kW and 4 kW systems, SUS304 plate with a thickness of 50 mm could be cut at the cutting speed of 0.1 m/min. Laser cutting of pipes from the internal surface was conducted using a newly developed small machining head which can rotate in the peripheral direction. Excellent quality for welding was confirmed. Cutting speed and plate thickness were improved by combining water jet cutter and YAG laser unit. 6 refs., 10 figs.

  8. 6kW class laser cutting equipment; 6kW daishutsuryoku laser setsudanki ni yoru atsuita setsudan

    Energy Technology Data Exchange (ETDEWEB)

    Nagata, Y.; Nagahori, M. [Tanaka Engineering Works Ltd., Saitama (Japan)

    1994-11-01

    Application of the laser cutting machine to the area of cutting steel plates of 5 mm thick or more was first enabled in 1990 by the 2 kW oscillator that was introduced in that year. The thick plate cutting industry has a short history. This paper describes the features and performance of the 6 kW laser cutting machine that was announced in April, 1994. The machine uses a newly developed high-speed axial flow type carbon dioxide laser oscillater with the rated output of 6 kW. As the discharge excitation method, the machine adopted the RF (radio frequency) method that causes low contamination in the discharge tube. The 6 kW laser cutting machine has a number of features such as a large cutting area provided by the oscillator contained in the cutting machine, cutting quality stabilized by the optical path length fixing unit, and automatic functions such as automatic setting of the cutting conditions and scheduled operation. The machine can cut mild steel plates of up to 40 mm thick (or up to 16 mm for stainless steel plates) at the cutting speed of 1600 mm/min for a 16 mm thick plate and 2200 mm/min for a 12 mm thick plate, with the good cut sectional surface. 5 figs., 1 tab.

  9. Perfect discretization of path integrals

    International Nuclear Information System (INIS)

    Steinhaus, Sebastian

    2012-01-01

    In order to obtain a well-defined path integral one often employs discretizations. In the case of General Relativity these generically break diffeomorphism symmetry, which has severe consequences since these symmetries determine the dynamics of the corresponding system. In this article we consider the path integral of reparametrization invariant systems as a toy example and present an improvement procedure for the discretized propagator. Fixed points and convergence of the procedure are discussed. Furthermore we show that a reparametrization invariant path integral implies discretization independence and acts as a projector onto physical states.

  10. Perfect discretization of path integrals

    Science.gov (United States)

    Steinhaus, Sebastian

    2012-05-01

    In order to obtain a well-defined path integral one often employs discretizations. In the case of General Relativity these generically break diffeomorphism symmetry, which has severe consequences since these symmetries determine the dynamics of the corresponding system. In this article we consider the path integral of reparametrization invariant systems as a toy example and present an improvement procedure for the discretized propagator. Fixed points and convergence of the procedure are discussed. Furthermore we show that a reparametrization invariant path integral implies discretization independence and acts as a projector onto physical states.

  11. Discovering Euler Circuits and Paths through a Culturally Relevant Lesson

    Science.gov (United States)

    Robichaux, Rebecca R.; Rodrigue, Paulette R.

    2006-01-01

    This article describes a middle school discrete mathematics lesson that uses the context of catching crawfish to provide students with a hands-on experience related to Euler circuits and paths. The lesson promotes mathematical communication through the use of cooperative learning as well as connections between mathematics and the real world…

  12. Piloting and Path Integration within and across Boundaries

    Science.gov (United States)

    Mou, Weimin; Wang, Lin

    2015-01-01

    Three experiments investigated whether navigation is less efficient across boundaries than within boundaries. In an immersive virtual environment, participants learned objects' locations in a large room or a small room. Participants then pointed to the objects' original locations after physically walking a circuitous path without vision.…

  13. Using road topology to improve cyclist path prediction

    NARCIS (Netherlands)

    Pool, E.A.I.; Kooij, J.F.P.; Gavrila, D.; Ioannou, Petros; Zhang, Wei-Bin; Lu, Meng

    2017-01-01

    We learn motion models for cyclist path prediction on real-world tracks obtained from a moving vehicle, and propose to exploit the local road topology to obtain better predictive distributions. The tracks are extracted from the Tsinghua-Daimler Cyclist Benchmark for cyclist detection, and corrected

  14. Cut Back on Your Kid's Sweet Treats: 10 Tips to Decrease Added Sugars

    Science.gov (United States)

    United States Department of Agriculture 10 tips Nutrition Education Series MyPlate MyWins Based on the Dietary Guidelines for Americans Cut back on your kid’s sweet treats Set your kids on a path for lifelong healthy eating by limiting the amount of added sugars they ...

  15. An Introduction to Path Analysis

    Science.gov (United States)

    Wolfe, Lee M.

    1977-01-01

    The analytical procedure of path analysis is described in terms of its use in nonexperimental settings in the social sciences. The description assumes a moderate statistical background on the part of the reader. (JKS)

  16. Probabilistic simulation of fermion paths

    International Nuclear Information System (INIS)

    Zhirov, O.V.

    1989-01-01

    Permutation symmetry of fermion path integral allows (while spin degrees of freedom are ignored) to use in its simulation any probabilistic algorithm, like Metropolis one, heat bath, etc. 6 refs., 2 tabs

  17. Formal language constrained path problems

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, C.; Jacob, R.; Marathe, M.

    1997-07-08

    In many path finding problems arising in practice, certain patterns of edge/vertex labels in the labeled graph being traversed are allowed/preferred, while others are disallowed. Motivated by such applications as intermodal transportation planning, the authors investigate the complexity of finding feasible paths in a labeled network, where the mode choice for each traveler is specified by a formal language. The main contributions of this paper include the following: (1) the authors show that the problem of finding a shortest path between a source and destination for a traveler whose mode choice is specified as a context free language is solvable efficiently in polynomial time, when the mode choice is specified as a regular language they provide algorithms with improved space and time bounds; (2) in contrast, they show that the problem of finding simple paths between a source and a given destination is NP-hard, even when restricted to very simple regular expressions and/or very simple graphs; (3) for the class of treewidth bounded graphs, they show that (i) the problem of finding a regular language constrained simple path between source and a destination is solvable in polynomial time and (ii) the extension to finding context free language constrained simple paths is NP-complete. Several extensions of these results are presented in the context of finding shortest paths with additional constraints. These results significantly extend the results in [MW95]. As a corollary of the results, they obtain a polynomial time algorithm for the BEST k-SIMILAR PATH problem studied in [SJB97]. The previous best algorithm was given by [SJB97] and takes exponential time in the worst case.

  18. Perfect discretization of path integrals

    OpenAIRE

    Steinhaus, Sebastian

    2011-01-01

    In order to obtain a well-defined path integral one often employs discretizations. In the case of General Relativity these generically break diffeomorphism symmetry, which has severe consequences since these symmetries determine the dynamics of the corresponding system. In this article we consider the path integral of reparametrization invariant systems as a toy example and present an improvement procedure for the discretized propagator. Fixed points and convergence of the procedure are discu...

  19. Solution path for manifold regularized semisupervised classification.

    Science.gov (United States)

    Wang, Gang; Wang, Fei; Chen, Tao; Yeung, Dit-Yan; Lochovsky, Frederick H

    2012-04-01

    Traditional learning algorithms use only labeled data for training. However, labeled examples are often difficult or time consuming to obtain since they require substantial human labeling efforts. On the other hand, unlabeled data are often relatively easy to collect. Semisupervised learning addresses this problem by using large quantities of unlabeled data with labeled data to build better learning algorithms. In this paper, we use the manifold regularization approach to formulate the semisupervised learning problem where a regularization framework which balances a tradeoff between loss and penalty is established. We investigate different implementations of the loss function and identify the methods which have the least computational expense. The regularization hyperparameter, which determines the balance between loss and penalty, is crucial to model selection. Accordingly, we derive an algorithm that can fit the entire path of solutions for every value of the hyperparameter. Its computational complexity after preprocessing is quadratic only in the number of labeled examples rather than the total number of labeled and unlabeled examples.

  20. Path integration in conical space

    International Nuclear Information System (INIS)

    Inomata, Akira; Junker, Georg

    2012-01-01

    Quantum mechanics in conical space is studied by the path integral method. It is shown that the curvature effect gives rise to an effective potential in the radial path integral. It is further shown that the radial path integral in conical space can be reduced to a form identical with that in flat space when the discrete angular momentum of each partial wave is replaced by a specific non-integral angular momentum. The effective potential is found proportional to the squared mean curvature of the conical surface embedded in Euclidean space. The path integral calculation is compatible with the Schrödinger equation modified with the Gaussian and the mean curvature. -- Highlights: ► We study quantum mechanics on a cone by the path integral approach. ► The path integral depends only on the metric and the curvature effect is built in. ► The approach is consistent with the Schrödinger equation modified by an effective potential. ► The effective potential is found to be of the “Jensen–Koppe” and “da Costa” type.

  1. Path integrals on curved manifolds

    International Nuclear Information System (INIS)

    Grosche, C.; Steiner, F.

    1987-01-01

    A general framework for treating path integrals on curved manifolds is presented. We also show how to perform general coordinate and space-time transformations in path integrals. The main result is that one has to subtract a quantum correction ΔV ∝ ℎ 2 from the classical Lagrangian L, i.e. the correct effective Lagrangian to be used in the path integral is L eff = L-ΔV. A general prescription for calculating the quantum correction ΔV is given. It is based on a canonical approach using Weyl-ordering and the Hamiltonian path integral defined by the midpoint prescription. The general framework is illustrated by several examples: The d-dimensional rotator, i.e. the motion on the sphere S d-1 , the path integral in d-dimensional polar coordinates, the exact treatment of the hydrogen atom in R 2 and R 3 by performing a Kustaanheimo-Stiefel transformation, the Langer transformation and the path integral for the Morse potential. (orig.)

  2. Path-based Queries on Trajectory Data

    DEFF Research Database (Denmark)

    Krogh, Benjamin Bjerre; Pelekis, Nikos; Theodoridis, Yannis

    2014-01-01

    In traffic research, management, and planning a number of path-based analyses are heavily used, e.g., for computing turn-times, evaluating green waves, or studying traffic flow. These analyses require retrieving the trajectories that follow the full path being analyzed. Existing path queries cannot...... sufficiently support such path-based analyses because they retrieve all trajectories that touch any edge in the path. In this paper, we define and formalize the strict path query. This is a novel query type tailored to support path-based analysis, where trajectories must follow all edges in the path...... a specific path by only retrieving data from the first and last edge in the path. To correctly answer strict path queries existing network-constrained trajectory indexes must retrieve data from all edges in the path. An extensive performance study of NETTRA using a very large real-world trajectory data set...

  3. Cutting edge technology to enhance nursing classroom instruction at Coppin State University.

    Science.gov (United States)

    Black, Crystal Day; Watties-Daniels, A Denyce

    2006-01-01

    Educational technologies have changed the paradigm of the teacher-student relationship in nursing education. Nursing students expect to use and to learn from cutting edge technology during their academic careers. Varied technology, from specified software programs (Tegrity and Blackboard) to the use of the Internet as a research medium, can enhance student learning. The authors provide an overview of current cutting edge technologies in nursing classroom instruction and its impact on future nursing practice.

  4. Equilibrium Analysis in Cake Cutting

    DEFF Research Database (Denmark)

    Branzei, Simina; Miltersen, Peter Bro

    2013-01-01

    Cake cutting is a fundamental model in fair division; it represents the problem of fairly allocating a heterogeneous divisible good among agents with different preferences. The central criteria of fairness are proportionality and envy-freeness, and many of the existing protocols are designed...... to guarantee proportional or envy-free allocations, when the participating agents follow the protocol. However, typically, all agents following the protocol is not guaranteed to result in a Nash equilibrium. In this paper, we initiate the study of equilibria of classical cake cutting protocols. We consider one...... of the simplest and most elegant continuous algorithms -- the Dubins-Spanier procedure, which guarantees a proportional allocation of the cake -- and study its equilibria when the agents use simple threshold strategies. We show that given a cake cutting instance with strictly positive value density functions...

  5. Document segmentation via oblique cuts

    Science.gov (United States)

    Svendsen, Jeremy; Branzan-Albu, Alexandra

    2013-01-01

    This paper presents a novel solution for the layout segmentation of graphical elements in Business Intelligence documents. We propose a generalization of the recursive X-Y cut algorithm, which allows for cutting along arbitrary oblique directions. An intermediate processing step consisting of line and solid region removal is also necessary due to presence of decorative elements. The output of the proposed segmentation is a hierarchical structure which allows for the identification of primitives in pie and bar charts. The algorithm was tested on a database composed of charts from business documents. Results are very promising.

  6. Correlation methods in cutting arcs

    Energy Technology Data Exchange (ETDEWEB)

    Prevosto, L; Kelly, H, E-mail: prevosto@waycom.com.ar [Grupo de Descargas Electricas, Departamento Ing. Electromecanica, Universidad Tecnologica Nacional, Regional Venado Tuerto, Laprida 651, Venado Tuerto (2600), Santa Fe (Argentina)

    2011-05-01

    The present work applies similarity theory to the plasma emanating from transferred arc, gas-vortex stabilized plasma cutting torches, to analyze the existing correlation between the arc temperature and the physical parameters of such torches. It has been found that the enthalpy number significantly influence the temperature of the electric arc. The obtained correlation shows an average deviation of 3% from the temperature data points. Such correlation can be used, for instance, to predict changes in the peak value of the arc temperature at the nozzle exit of a geometrically similar cutting torch due to changes in its operation parameters.

  7. Correlation methods in cutting arcs

    International Nuclear Information System (INIS)

    Prevosto, L; Kelly, H

    2011-01-01

    The present work applies similarity theory to the plasma emanating from transferred arc, gas-vortex stabilized plasma cutting torches, to analyze the existing correlation between the arc temperature and the physical parameters of such torches. It has been found that the enthalpy number significantly influence the temperature of the electric arc. The obtained correlation shows an average deviation of 3% from the temperature data points. Such correlation can be used, for instance, to predict changes in the peak value of the arc temperature at the nozzle exit of a geometrically similar cutting torch due to changes in its operation parameters.

  8. Assistência de enfermagem ao portador de alterações na integridade cutânea: um relato de experiência de ensino-aprendizagem Asistencia de enfermería al portador de alteraciones en la integridad cutánea: un relato de experiencia de enseñanza-aprendizage Nursing asistence to the bearer of alterations in the cutaneous integrity: a learning education experience account

    Directory of Open Access Journals (Sweden)

    Maria José Sanches Marin

    2002-12-01

    Full Text Available O Curso de Enfermagem da Faculdade de Medicina de Marília, vem empenhando-se na construção do Currículo Integrado, utilizando-se da metodologia problematizadora. No presente estudo, os autores apresentam os desempenhos esperados dos estudantes e a seqüência de atividades construída para o ensino dos cuidados de enfermagem ao adulto e idoso portador de alteração da integridade cutânea, a qual permite ao aluno implementar este conhecimento em sua realidade prática. No decorrer das atividades constata-se que tal desafio tem representado um avanço no processo de ensino e aprendizagem, no entanto, apontam-se algumas dificuldades a serem superadas.El Curso de Enfermería de la Facultad de Medicina de Marilia se está empeñando en la construcción de un curriculun integrado, utilizándose de la metodologia problemática. En este estudio, los autores presentan el desarrollo esperado de los estudiantes y la secuencia de actividades construída para la enseñanza de los cuidados de enfermería al adulto y al mayor portador de alteración a la integridad cutánea, la cual permite que el alumno aplique este conocimiento a su realidad práctica. En el transcurso de las actividades se nota que dicho desafio representa un avance en el proceso de enseñanza y aprendizage, pero, algunas dificultades son apuntadas y deben ser superadas.The Nursing Course at the Medicine College in Marília, has been making every efforts to create the Integrate Curiculum, making use of the questionable methodology. In this study, the authors present the student' expected performances and the sequency of activities creat to teach the precautions of Nursing for the adult and elder people taking away some changes na the cutaneous integrity, that makes the student implement the konowlege. During the activities it was proved that this kind of challenge has showed a progress in the teachin and learning process, but there are some difficulties to be conquered.

  9. Covering path generation for autonomous turf-care vehicle

    DEFF Research Database (Denmark)

    Mai, Christian; Jouffroy, Jerome; Top, Søren

    2017-01-01

    A covering path generation algorithm is developed to generate a lengthwise pattern based on a polygon describing the outer boundary and obstacles (polygon holes) of a geographical area. The algorithm is applied to an autonomous lawn-care robot for application to large grass turfs, for example golf......-courses, which require structured and precise cutting patterns. The geographical polygon is recorded by manually driving the vehicle around the contour, resulting in a polygon given as geographical (latitude, longitude) coordinates of the vertices, which together with machine parameters are used to generate...... a suitable toolpath. The algorithm has been tested on a recorded polygon from a local park turf which is non-convex and has holes, illustrating the algorithm functionality and limitations wrt. optimality. In particular, the algorithm can generate a tool-path for any polygon orientation....

  10. Cutting temperature measurement and material machinability

    Directory of Open Access Journals (Sweden)

    Nedić Bogdan P.

    2014-01-01

    Full Text Available Cutting temperature is very important parameter of cutting process. Around 90% of heat generated during cutting process is then away by sawdust, and the rest is transferred to the tool and workpiece. In this research cutting temperature was measured with artificial thermocouples and question of investigation of metal machinability from aspect of cutting temperature was analyzed. For investigation of material machinability during turning artificial thermocouple was placed just below the cutting top of insert, and for drilling thermocouples were placed through screw holes on the face surface. In this way was obtained simple, reliable, economic and accurate method for investigation of cutting machinability.

  11. Stresses in ultrasonically assisted bone cutting

    International Nuclear Information System (INIS)

    Alam, K; Mitrofanov, A V; Silberschmidt, V V; Baeker, M

    2009-01-01

    Bone cutting is a frequently used procedure in the orthopaedic surgery. Modern cutting techniques, such as ultrasonic assisted drilling, enable surgeons to perform precision operations in facial and spinal surgeries. Advanced understanding of the mechanics of bone cutting assisted by ultrasonic vibration is required to minimise bone fractures and to optimise the technique performance. The paper presents results of finite element simulations on ultrasonic and conventional bone cutting analysing the effects of ultrasonic vibration on cutting forces and stress distribution. The developed model is used to study the effects of cutting and vibration parameters (e.g. amplitude and frequency) on the stress distributions in the cutting region.

  12. Covering path generation for autonomous turf-care vehicle

    DEFF Research Database (Denmark)

    Mai, Christian; Jouffroy, Jerome; Top, Søren

    2017-01-01

    A covering path generation algorithm is developed to generate a lengthwise pattern based on a polygon describing the outer boundary and obstacles (polygon holes) of a geographical area. The algorithm is applied to an autonomous lawn-care robot for application to large grass turfs, for example golf......-courses, which require structured and precise cutting patterns. The geographical polygon is recorded by manually driving the vehicle around the contour, resulting in a polygon given as geographical (latitude, longitude) coordinates of the vertices, which together with machine parameters are used to generate...

  13. Cutting system for burnable poison rod

    International Nuclear Information System (INIS)

    Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

    1989-01-01

    Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

  14. Path integration on hyperbolic spaces

    Energy Technology Data Exchange (ETDEWEB)

    Grosche, C [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

    1991-11-01

    Quantum mechanics on the hyperbolic spaces of rank one is discussed by path integration technique. Hyperbolic spaces are multi-dimensional generalisation of the hyperbolic plane, i.e. the Poincare upper half-plane endowed with a hyperbolic geometry. We evalute the path integral on S{sub 1} {approx equal} SO (n,1)/SO(n) and S{sub 2} {approx equal} SU(n,1)/S(U(1) x U(n)) in a particular coordinate system, yielding explicitly the wave-functions and the energy spectrum. Futhermore we can exploit a general property of all these spaces, namely that they can be parametrized by a pseudopolar coordinate system. This allows a separation in path integration over spheres and an additional path integration over the remaining hyperbolic coordinate, yielding effectively a path integral for a modified Poeschl-Teller potential. Only continuous spectra can exist in all the cases. For all the hyperbolic spaces of rank one we find a general formula for the largest lower bound (zero-point energy) of the spectrum which is given by E{sub O} = h{sup 2} /8m(m{sub {alpha}} +2m{sub 2} {alpha}){sup 2} (m {alpha} and m{sub 2}{alpha} denote the dimension of the root subspace corresponding to the roots {alpha} and 2{alpha}, respectively). I also discuss the case, where a constant magnetic field on H{sup n} is incorporated. (orig.).

  15. Path integration on hyperbolic spaces

    International Nuclear Information System (INIS)

    Grosche, C.

    1991-11-01

    Quantum mechanics on the hyperbolic spaces of rank one is discussed by path integration technique. Hyperbolic spaces are multi-dimensional generalisation of the hyperbolic plane, i.e. the Poincare upper half-plane endowed with a hyperbolic geometry. We evalute the path integral on S 1 ≅ SO (n,1)/SO(n) and S 2 ≅ SU(n,1)/S[U(1) x U(n)] in a particular coordinate system, yielding explicitly the wave-functions and the energy spectrum. Futhermore we can exploit a general property of all these spaces, namely that they can be parametrized by a pseudopolar coordinate system. This allows a separation in path integration over spheres and an additional path integration over the remaining hyperbolic coordinate, yielding effectively a path integral for a modified Poeschl-Teller potential. Only continuous spectra can exist in all the cases. For all the hyperbolic spaces of rank one we find a general formula for the largest lower bound (zero-point energy) of the spectrum which is given by E O = h 2 /8m(m α +2m 2 α) 2 (m α and m 2 α denote the dimension of the root subspace corresponding to the roots α and 2α, respectively). I also discuss the case, where a constant magnetic field on H n is incorporated. (orig.)

  16. Wedge cutting of mild steel by CO 2 laser and cut-quality assessment in relation to normal cutting

    Science.gov (United States)

    Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

    2008-10-01

    In some applications, laser cutting of wedge surfaces cannot be avoided in sheet metal processing and the quality of the end product defines the applicability of the laser-cutting process in such situations. In the present study, CO 2 laser cutting of the wedge surfaces as well as normal surfaces (normal to laser beam axis) is considered and the end product quality is assessed using the international standards for thermal cutting. The cut surfaces are examined by the optical microscopy and geometric features of the cut edges such as out of flatness and dross height are measured from the micrographs. A neural network is introduced to classify the striation patterns of the cut surfaces. It is found that the dross height and out of flatness are influenced significantly by the laser output power, particularly for wedge-cutting situation. Moreover, the cut quality improves at certain value of the laser power intensity.

  17. Chip & Cut Tests an Elastomeren

    OpenAIRE

    Euchler, Eric; Heinrich, Gert; Michael, Hannes; Gehde, Michael; Stocek, Radek; Kratina, Ondrej; Kipscholl, Reinhold

    2016-01-01

    Dieser Vortrag stellt einen neuartigen Prüfstand vor, mit welchem das Chip & Cut Verhalten von Elastomeren charakterisiert werden kann. Sowohl theoretischer Hintergrund als auch praktische Erkenntnisse werden diskutiert. Die Vorstellung der Praxisrelevanz dieser Untersuchungen steht im Fokus des Vortrags.

  18. The Cutting-Edge Challenge

    Science.gov (United States)

    Share, Joani

    2005-01-01

    In a time of educational budget cuts, the arts seem to take the major brunt of the financial ax. Fine arts programs are often pitted against one another for survival. The music industry and supporting corporations, such as American Express, campaign to have instruments donated or purchased to keep educational programs alive. The visual arts do not…

  19. Why I like power cuts...

    CERN Multimedia

    Computer Security Team

    2012-01-01

    Accidental power cuts - a permanent nuisance when running accelerators or computing services, since it takes a lot of time to recover from them. While I feel very sorry for those who are under pressure to get their service running again and deeply regret the loss of down-time and availability, I must admit that I like power cuts: power cuts make computers reboot! And rebooting computers at CERN means all the pending software patches are automatically applied.   But don’t think I am egotistic enough to endorse power cuts. Not necessarily! I am already happy if you regularly patch your computer(s) yourself, where regularly means at least once a month: · If you run a centrally or locally managed Windows computer, give that small orange blinking “CMF” icon in the taskbar a chance in the evening to apply all the pending patches. Also, let it initiate a reboot at the end! · If you have a personal computer with your own Windows operating system, ...

  20. Culture in Language Learning: Background, Issues and Implications

    Directory of Open Access Journals (Sweden)

    Omid Pourkalhor

    2017-03-01

    Full Text Available The present study aimed at presenting the historical background of the emergence of culture in language learning and how it can be correlated with the language learners. In fact, by providing various definitions of culture and the role it might play in the process of language learning, whether directly or indirectly, this research provides a clear-cut overview of culture and its application among the people as well as their communication in the society. Moreover, the relationship between culture and language learning is also taken into account. To this end, basic definitions of culture in different research studies are investigated moving toward finding a path to make a connection between language and culture. Therefore, a review of studies on the relationship between language learning and culture is provided to account for the possible effectiveness of benefiting from culture in the language learning process in that the learning context (i.e. foreign or second language can be affected by the culture of the teachers as well as the learners. This demands that both teachers and learners should be aware of cultural issues surrounding the language and the fact that it can be beneficial for the process of language learning. If learner are consciously involved in the culture of the language they are learning, they certainly can have better performance and understand the language more tangibly.

  1. Analysis of changes in paper cutting forces during the cutting cycle in single-knife guillotine

    OpenAIRE

    Rusin, Agnieszka; Petriaszwili, Georgij

    2013-01-01

    Paper presents the results of changes in the three components of cutting forces of paper stacks cutting during the cutting cycle in single-knife guillotine. The changes of the three components of cutting force at different stages of cutting cycle were analyzed.

  2. Path Integrals in Quantum Mechanics

    International Nuclear Information System (INIS)

    Louko, J

    2005-01-01

    Jean Zinn-Justin's textbook Path Integrals in Quantum Mechanics aims to familiarize the reader with the path integral as a calculational tool in quantum mechanics and field theory. The emphasis is on quantum statistical mechanics, starting with the partition function Tr exp(-β H) and proceeding through the diffusion equation to barrier penetration problems and their semiclassical limit. The 'real time' path integral is defined via analytic continuation and used for the path-integral representation of the nonrelativistic S-matrix and its perturbative expansion. Holomorphic and Grassmannian path integrals are introduced and applied to nonrelativistic quantum field theory. There is also a brief discussion of path integrals in phase space. The introduction includes a brief historical review of path integrals, supported by a bibliography with some 40 entries. As emphasized in the introduction, mathematical rigour is not a central issue in the book. This allows the text to present the calculational techniques in a very readable manner: much of the text consists of worked-out examples, such as the quartic anharmonic oscillator in the barrier penetration chapter. At the end of each chapter there are exercises, some of which are of elementary coursework type, but the majority are more in the style of extended examples. Most of the exercises indeed include the solution or a sketch thereof. The book assumes minimal previous knowledge of quantum mechanics, and some basic quantum mechanical notation is collected in an appendix. The material has a large overlap with selected chapters in the author's thousand-page textbook Quantum Field Theory and Critical Phenomena (2002 Oxford: Clarendon). The stand-alone scope of the present work has, however, allowed a more focussed organization of this material, especially in the chapters on, respectively, holomorphic and Grassmannian path integrals. In my view the book accomplishes its aim admirably and is eminently usable as a textbook

  3. From path integrals to anyons

    International Nuclear Information System (INIS)

    Canright, G.S.

    1992-01-01

    I offer a pedagogical review of the homotopy arguments for fractional statistics in two dimensions. These arguments arise naturally in path-integral language since they necessarily consider the properties of paths rather than simply permutations. The braid group replaces the permutation group as the basic structure for quantum statistics; hence properties of the braid group on several surfaces are briefly discussed. Finally, the question of multiple (real-space) occupancy is addressed; I suggest that the ''traditional'' treatment of this question (ie, an assumption that many-anyon wavefunctions necessarily vanish for multiple occupancy) needs reexamination

  4. Data Science in Radiology: A Path Forward.

    Science.gov (United States)

    Aerts, Hugo J W L

    2018-02-01

    Artificial intelligence (AI), especially deep learning, has the potential to fundamentally alter clinical radiology. AI algorithms, which excel in quantifying complex patterns in data, have shown remarkable progress in applications ranging from self-driving cars to speech recognition. The AI application within radiology, known as radiomics, can provide detailed quantifications of the radiographic characteristics of underlying tissues. This information can be used throughout the clinical care path to improve diagnosis and treatment planning, as well as assess treatment response. This tremendous potential for clinical translation has led to a vast increase in the number of research studies being conducted in the field, a number that is expected to rise sharply in the future. Many studies have reported robust and meaningful findings; however, a growing number also suffer from flawed experimental or analytic designs. Such errors could not only result in invalid discoveries, but also may lead others to perpetuate similar flaws in their own work. This perspective article aims to increase awareness of the issue, identify potential reasons why this is happening, and provide a path forward. Clin Cancer Res; 24(3); 532-4. ©2017 AACR . ©2017 American Association for Cancer Research.

  5. Flexible integration of path-planning capabilities

    Science.gov (United States)

    Stobie, Iain C.; Tambe, Milind; Rosenbloom, Paul S.

    1993-05-01

    Robots pursuing complex goals must plan paths according to several criteria of quality, including shortness, safety, speed and planning time. Many sources and kinds of knowledge, such as maps, procedures and perception, may be available or required. Both the quality criteria and sources of knowledge may vary widely over time, and in general they will interact. One approach to address this problem is to express all criteria and goals numerically in a single weighted graph, and then to search this graph to determine a path. Since this is problematic with symbolic or uncertain data and interacting criteria, we propose that what is needed instead is an integration of many kinds of planning capabilities. We describe a hybrid approach to integration, based on experiments with building simulated mobile robots using Soar, an integrated problem-solving and learning system. For flexibility, we have implemented a combination of internal planning, reactive capabilities and specialized tools. We illustrate how these components can complement each other's limitations and produce plans which integrate geometric and task knowledge.

  6. Isomorphisms and traversability of directed path graphs

    NARCIS (Netherlands)

    Broersma, Haitze J.; Li, Xueliang; Li, X.

    1998-01-01

    The concept of a line digraph is generalized to that of a directed path graph. The directed path graph $\\forw P_k(D)$ of a digraph $D$ is obtained by representing the directed paths on $k$ vertices of $D$ by vertices. Two vertices are joined by an arc whenever the corresponding directed paths in $D$

  7. Five-axis Control Processing Using NC Machine Tools : A Tool Posture Decision Using the Tangent Slope at a Cut Point on a Work

    OpenAIRE

    小島, 龍広; 西田, 知照; 扇谷, 保彦

    2003-01-01

    This report deals with the way to decide tool posture and the way to analytically calculate tool path for the work shape requiring 5-axis control machining. In the tool path calculation, basic equations are derived using the principle that the tangent slope at a cut point on a work and the one at a cutting point on a tool edge are identical. A tool posture decision procedure using the tangent slope at each cut point on a work is proposed for any shape of tool edge. The valid- ity of the way t...

  8. Model for Reggeon-Pomeranchukon cuts

    International Nuclear Information System (INIS)

    Chia, S.

    1977-01-01

    A model is presented for calculating Reggeon-Pomeranchukon cuts, making use explicitly of the Mandelstam diagram. External spins are treated in a natural way. Calculation for the general case is outlined and it is shown that in practical application the cut can be calculated in a standard way. Cuts associated with the exchanges of π, rho, B, and A 2 are considered, and characteristics of the RP cuts, as well as the structure functions, are extracted and discussed. It is found that the model differs considerably from the absorption model. Two suppression schemes are operative which control the magnitudes of cut contributions to amplitudes with ''naturality'' opposite to the Reggeon. The πP cut is found to be a unique case because of the smallness of the pion mass. In general, the RP cuts are self-conspiratorial. At very high energies, all cuts, except πP cut, exhibit quasifactorization

  9. Development of underwater laser cutting technology

    International Nuclear Information System (INIS)

    Sato, Seiichi; Inaba, Takanori; Inose, Koutarou; Matsumoto, Naoyuki; Sakakibara, Yuji

    2015-01-01

    In is desirable to use remote underwater device for the decommissioning work of highly radioactive components such as the nuclear internals from a view point of reducing the ranitidine exposure to the worker. Underwater laser cutting technology has advantages. First advantage in underwater laser cutting technology is that low reaction force during cutting, namely, remote operability is superior. Second point is that underwater laser cutting generates a little amount of secondary waste, because cutting kerf size is very small. Third point is that underwater laser cutting has low risk of the process delay, because device trouble is hard to happen. While underwater laser cutting has many advantages, the careful consideration in the safe treatment of the offgas which underwater laser cutting generates is necessary. This paper describes outline of underwater laser cutting technology developed by IHI Corporation (IHI) and that this technology is effective in various dismantling works in water. (author)

  10. Quality Analysis of Cutting Steel Using Laser

    Directory of Open Access Journals (Sweden)

    Vladislav Markovič

    2013-02-01

    Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

  11. Quality Analysis of Cutting Steel Using Laser

    Directory of Open Access Journals (Sweden)

    Vladislav Markovič

    2012-12-01

    Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

  12. Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

    Science.gov (United States)

    Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

    2017-01-01

    In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

  13. Qualification paths of adult educators in Sweden and Denmark

    DEFF Research Database (Denmark)

    Andersson, Per; Köpsén, Susanne; Larson, Anne

    2013-01-01

    fields of education and training. In this study, we analyse the qualification paths, or learning trajectories, of prospective adult educators in Sweden and Denmark. The analysis is based on narrative interviews with 29 students in training to become adult educators. The career paths of adult educators...... are often long and winding roads. Becoming an adult educator could be their primary desire, but it could also be their ‘Plan B’, a second choice. Individual motives and external demands interact in the professionalisation process. A shift in focus from teaching subject and methods to teaching context...... and the relation to the learners is part of the professional development. Finally, we argue that both academic studies and hands-on work in the adult education community are crucial parts of the adult educator’s qualification path....

  14. Laser Cutting of Thin Nickel Bellows

    Science.gov (United States)

    Butler, C. L.

    1986-01-01

    Laser cutting technique produces narrow, precise, fast, and repeatable cuts in thin nickel-allow bellows material. Laser cutting operation uses intense focused beam to melt material and assisting gas to force melted material through part thickness, creating void. When part rotated or moved longitudinally, melting and material removal continuous and creates narrow, fast, precise, and repeatable cut. Technique used to produce cuts of specified depths less than material thickness. Avoids distortion, dents, and nicks produced in delicate materials during lathe trimming operations, which require high cutting-tool pressure and holding-fixture forces.

  15. The generalized good cut equation

    International Nuclear Information System (INIS)

    Adamo, T M; Newman, E T

    2010-01-01

    The properties of null geodesic congruences (NGCs) in Lorentzian manifolds are a topic of considerable importance. More specifically NGCs with the special property of being shear-free or asymptotically shear-free (as either infinity or a horizon is approached) have received a great deal of recent attention for a variety of reasons. Such congruences are most easily studied via solutions to what has been referred to as the 'good cut equation' or the 'generalization good cut equation'. It is the purpose of this paper to study these equations and show their relationship to each other. In particular we show how they all have a four-complex-dimensional manifold (known as H-space, or in a special case as complex Minkowski space) as a solution space.

  16. Water-Cut Sensor System

    KAUST Repository

    Karimi, Muhammad Akram

    2018-01-11

    Provided in some embodiments is a method of manufacturing a pipe conformable water-cut sensors system. Provided in some embodiments is method for manufacturing a water-cut sensor system that includes providing a helical T-resonator, a helical ground conductor, and a separator at an exterior of a cylindrical pipe. The helical T-resonator including a feed line, and a helical open shunt stub conductively coupled to the feed line. The helical ground conductor including a helical ground plane opposite the helical open shunt stub and a ground ring conductively coupled to the helical ground plane. The feed line overlapping at least a portion of the ground ring, and the separator disposed between the feed line and the portion of the ground ring overlapped by the feed line to electrically isolate the helical T-resonator from the helical ground conductor.

  17. Variable angle asymmetric cut monochromator

    International Nuclear Information System (INIS)

    Smither, R.K.; Fernandez, P.B.

    1993-09-01

    A variable incident angle, asymmetric cut, double crystal monochromator was tested for use on beamlines at the Advanced Photon Source (APS). For both undulator and wiggler beams the monochromator can expand area of footprint of beam on surface of the crystals to 50 times the area of incident beam; this will reduce the slope errors by a factor of 2500. The asymmetric cut allows one to increase the acceptance angle for incident radiation and obtain a better match to the opening angle of the incident beam. This can increase intensity of the diffracted beam by a factor of 2 to 5 and can make the beam more monochromatic, as well. The monochromator consists of two matched, asymmetric cut (18 degrees), silicon crystals mounted so that they can be rotated about three independent axes. Rotation around the first axis controls the Bragg angle. The second rotation axis is perpendicular to the diffraction planes and controls the increase of the area of the footprint of the beam on the crystal surface. Rotation around the third axis controls the angle between the surface of the crystal and the wider, horizontal axis for the beam and can make the footprint a rectangle with a minimum. length for this area. The asymmetric cut is 18 degrees for the matched pair of crystals, which allows one to expand the footprint area by a factor of 50 for Bragg angles up to 19.15 degrees (6 keV for Si[111] planes). This monochromator, with proper cooling, will be useful for analyzing the high intensity x-ray beams produced by both undulators and wigglers at the APS

  18. Drill cuttings mount formation study

    Science.gov (United States)

    Teh, Su Yean; Koh, Hock Lye

    2014-07-01

    Oil, Gas and Energy sector has been identified as an essential driving force in the Malaysian Economic Transformation Programs (ETP). Recently confirmed discovery of many offshore oil and gas deposits in Malaysian waters has ignited new confidence in this sector. However, this has also spurred intense interest on safeguarding the health and environment of coastal waters in Malaysia from adverse impact resulting from offshore oil and gas production operation. Offshore discharge of spent drilling mud and rock cuttings is the least expensive and simplest option to dispose of large volumes of drilling wastes. But this onsite offshore disposal may have adverse environmental impacts on the water column and the seabed. It may also pose occupational health hazards to the workers living in the offshore platforms. It is therefore important to model the transport and deposition of drilling mud and rock cuttings in the sea to enable proper assessment of their adverse impacts on the environment and the workers. Further, accumulation of drill particles on the seabed may impede proper operation of pipelines on the seabed. In this paper, we present an in-house application model TUNA-PT developed to cater to local oil and gas industry needs to simulate the dispersion and mount formation of drill cuttings by offshore oil and gas exploration and production platforms. Using available data on Malaysian coastal waters, simulation analyses project a pile formation on the seabed with a maximum height of about 1 m and pile radius of around 30 to 50 m. Simulated pile heights are not sensitive to the heights of release of the cuttings as the sensitivity has been mitigated by the depth of water.

  19. Effectiveness of interactive tutorials in promoting "which-path" information reasoning in advanced quantum mechanics

    Science.gov (United States)

    Maries, Alexandru; Sayer, Ryan; Singh, Chandralekha

    2017-12-01

    Research suggests that introductory physics students often have difficulty using a concept in contexts different from the ones in which they learned it without explicit guidance to help them make the connection between the different contexts. We have been investigating advanced students' learning of quantum mechanics concepts and have developed interactive tutorials which strive to help students learn these concepts. Two such tutorials, focused on the Mach-Zehnder interferometer (MZI) and the double-slit experiment (DSE), help students learn how to use the concept of "which-path" information to reason about the presence or absence of interference in these two experiments in different situations. After working on a pretest that asked students to predict interference in the MZI with single photons and polarizers of various orientations placed in one or both paths of the MZI, students worked on the MZI tutorial which, among other things, guided them to reason in terms of which-path information in order to predict interference in similar situations. We investigated the extent to which students were able to use reasoning related to which-path information learned in the MZI tutorial to answer analogous questions on the DSE (before working on the DSE tutorial). After students worked on the DSE pretest they worked on a DSE tutorial in which they learned to use the concept of which-path information to answer questions about interference in the DSE with single particles with mass sent through the two slits and a monochromatic lamp placed between the slits and the screen. We investigated if this additional exposure to the concept of which-path information promoted improved learning and performance on the DSE questions with single photons and polarizers placed after one or both slits. We find evidence that both tutorials promoted which-path information reasoning and helped students use this reasoning appropriately in contexts different from the ones in which they had learned

  20. Aqueous cutting fluid for machining fissionable materials

    Science.gov (United States)

    Duerksen, Walter K.; Googin, John M.; Napier, Jr., Bradley

    1984-01-01

    The present invention is directed to a cutting fluid for machining fissionable material. The cutting fluid is formed of glycol, water and boron compound in an adequate concentration for effective neutron attenuation so as to inhibit criticality incidents during machining.

  1. Submerged cutting characteristics of abrasive suspension jet

    International Nuclear Information System (INIS)

    Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroyuki

    2015-01-01

    An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth under submerged condition divided by the cutting depth in air at the same standoff distance. The relative cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

  2. Method of cutting radioactivated metal structures

    International Nuclear Information System (INIS)

    Takimoto, Yoshinori; Sakota, Kotaro; Hamamoto, Noboru; Harada, Keizo.

    1985-01-01

    Purpose: To improve the cutting performance to a level as comparable with that in air, as well as prevent the scattering of the radioactive materials upon cutting to the level as that in water cutting. Method: After igniting a gas cutting torch automatically, water spray by the local water sprayer is started by the actuation of a submerged pump, while a gas cutting manipulator is operated to cut the nuclear reactor pressure vessel. In this way, cutting exhaust gases resulted from the gas cutting torch are water-washed by the spray from the local water sprayer and falls within the nuclear rector pressure vessel in the form of water streams or droplets along the inner wall surface of the pressure vessel. Further, water is fed again to the local water sprayer by the submerged pump. (Kawakami, Y.)

  3. Transfer Paths of Research Results to the Practice: Observations From the Receiving End

    Science.gov (United States)

    Findikakis, A. N.

    2005-12-01

    A non-scientific poll of fellow practicing professionals suggests that there is a range of opinions regarding the effectiveness of different ways of becoming acquainted with and using the results of academic research in their practice. Journal articles remain the dominant path for transferring research results to the profession, even though accessing them is becoming more difficult with time. Driven primarily by cost considerations personal and corporate subscriptions seem to be on the decline. Libraries are one of the first victims of cost cutting measures in the industry. Even though the availability of journal articles in electronic form facilitates their availability, their prices are prohibitive. This is especially true during when a professional is searching for a solution to a problem and may have to review several papers on the subject. One colleague suggested that the professional organizations and other publishers of research articles could learn from the experience of the music industry, by lowering the cost of downloading individual papers to something like a dollar per article, recovering thus their production costs through the increase in the volume of purchased articles. The posting on the internet of special reports and dissertations by research institutions is viewed as very useful by those working in practice. The distribution through the internet of reports by federal organizations conducting or sponsoring research, such as the U.S. Geological Survey and the U.S. Environmental Protection Agency is greatly appreciated by the practicing professionals. The use of leading researchers as consultants provides a direct path for bringing research results to the practice, but it is limited to a small number of cases where bringing in a consultant can be justified. Short courses are viewed as an effective way of familiarizing professionals with the latest research findings on specific subjects. The notes distributed in such courses are considered

  4. Cutting-Edge Technologies and Social Media Use in Higher Education

    Science.gov (United States)

    Benson, Vladlena, Ed.; Morgan, Stephanie

    2014-01-01

    The inclusion of social media in higher education has transformed the way instructors teach and students learn. In order to effectively reach their students in this networked world, teachers must learn to utilize the latest technologies in their classrooms. "Cutting-Edge Technologies and Social Media Use in Higher Education" brings…

  5. DiversePathsJ: diverse shortest paths for bioimage analysis.

    Science.gov (United States)

    Uhlmann, Virginie; Haubold, Carsten; Hamprecht, Fred A; Unser, Michael

    2018-02-01

    We introduce a formulation for the general task of finding diverse shortest paths between two end-points. Our approach is not linked to a specific biological problem and can be applied to a large variety of images thanks to its generic implementation as a user-friendly ImageJ/Fiji plugin. It relies on the introduction of additional layers in a Viterbi path graph, which requires slight modifications to the standard Viterbi algorithm rules. This layered graph construction allows for the specification of various constraints imposing diversity between solutions. The software allows obtaining a collection of diverse shortest paths under some user-defined constraints through a convenient and user-friendly interface. It can be used alone or be integrated into larger image analysis pipelines. http://bigwww.epfl.ch/algorithms/diversepathsj. michael.unser@epfl.ch or fred.hamprecht@iwr.uni-heidelberg.de. Supplementary data are available at Bioinformatics online. © The Author(s) 2017. Published by Oxford University Press.

  6. Spreading paths in partially observed social networks

    Science.gov (United States)

    Onnela, Jukka-Pekka; Christakis, Nicholas A.

    2012-03-01

    Understanding how and how far information, behaviors, or pathogens spread in social networks is an important problem, having implications for both predicting the size of epidemics, as well as for planning effective interventions. There are, however, two main challenges for inferring spreading paths in real-world networks. One is the practical difficulty of observing a dynamic process on a network, and the other is the typical constraint of only partially observing a network. Using static, structurally realistic social networks as platforms for simulations, we juxtapose three distinct paths: (1) the stochastic path taken by a simulated spreading process from source to target; (2) the topologically shortest path in the fully observed network, and hence the single most likely stochastic path, between the two nodes; and (3) the topologically shortest path in a partially observed network. In a sampled network, how closely does the partially observed shortest path (3) emulate the unobserved spreading path (1)? Although partial observation inflates the length of the shortest path, the stochastic nature of the spreading process also frequently derails the dynamic path from the shortest path. We find that the partially observed shortest path does not necessarily give an inflated estimate of the length of the process path; in fact, partial observation may, counterintuitively, make the path seem shorter than it actually is.

  7. Spreading paths in partially observed social networks.

    Science.gov (United States)

    Onnela, Jukka-Pekka; Christakis, Nicholas A

    2012-03-01

    Understanding how and how far information, behaviors, or pathogens spread in social networks is an important problem, having implications for both predicting the size of epidemics, as well as for planning effective interventions. There are, however, two main challenges for inferring spreading paths in real-world networks. One is the practical difficulty of observing a dynamic process on a network, and the other is the typical constraint of only partially observing a network. Using static, structurally realistic social networks as platforms for simulations, we juxtapose three distinct paths: (1) the stochastic path taken by a simulated spreading process from source to target; (2) the topologically shortest path in the fully observed network, and hence the single most likely stochastic path, between the two nodes; and (3) the topologically shortest path in a partially observed network. In a sampled network, how closely does the partially observed shortest path (3) emulate the unobserved spreading path (1)? Although partial observation inflates the length of the shortest path, the stochastic nature of the spreading process also frequently derails the dynamic path from the shortest path. We find that the partially observed shortest path does not necessarily give an inflated estimate of the length of the process path; in fact, partial observation may, counterintuitively, make the path seem shorter than it actually is.

  8. Study of Cutting Edge Temperature and Cutting Force of End Mill Tool in High Speed Machining

    Directory of Open Access Journals (Sweden)

    Kiprawi Mohammad Ashaari

    2017-01-01

    Full Text Available A wear of cutting tools during machining process is unavoidable due to the presence of frictional forces during removing process of unwanted material of workpiece. It is unavoidable but can be controlled at slower rate if the cutting speed is fixed at certain point in order to achieve optimum cutting conditions. The wear of cutting tools is closely related with the thermal deformations that occurred between the frictional contact point of cutting edge of cutting tool and workpiece. This research paper is focused on determinations of relationship among cutting temperature, cutting speed, cutting forces and radial depth of cutting parameters. The cutting temperature is determined by using the Indium Arsenide (InAs and Indium Antimonide (InSb photocells to measure infrared radiation that are emitted from cutting tools and cutting forces is determined by using dynamometer. The high speed machining process is done by end milling the outer surface of carbon steel. The signal from the photocell is digitally visualized in the digital oscilloscope. Based on the results, the cutting temperature increased as the radial depth and cutting speed increased. The cutting forces increased when radial depth increased but decreased when cutting speed is increased. The setup for calibration and discussion of the experiment will be explained in this paper.

  9. Learning

    Directory of Open Access Journals (Sweden)

    Mohsen Laabidi

    2014-01-01

    Full Text Available Nowadays learning technologies transformed educational systems with impressive progress of Information and Communication Technologies (ICT. Furthermore, when these technologies are available, affordable and accessible, they represent more than a transformation for people with disabilities. They represent real opportunities with access to an inclusive education and help to overcome the obstacles they met in classical educational systems. In this paper, we will cover basic concepts of e-accessibility, universal design and assistive technologies, with a special focus on accessible e-learning systems. Then, we will present recent research works conducted in our research Laboratory LaTICE toward the development of an accessible online learning environment for persons with disabilities from the design and specification step to the implementation. We will present, in particular, the accessible version “MoodleAcc+” of the well known e-learning platform Moodle as well as new elaborated generic models and a range of tools for authoring and evaluating accessible educational content.

  10. Optical Cutting Interruption Sensor for Fiber Lasers

    Directory of Open Access Journals (Sweden)

    Benedikt Adelmann

    2015-09-01

    Full Text Available We report on an optical sensor system attached to a 4 kW fiber laser cutting machine to detect cutting interruptions. The sensor records the thermal radiation from the process zone with a modified ring mirror and optical filter arrangement, which is placed between the cutting head and the collimator. The process radiation is sensed by a Si and InGaAs diode combination with the detected signals being digitalized with 20 kHz. To demonstrate the function of the sensor, signals arising during fusion cutting of 1 mm stainless steel and mild steel with and without cutting interruptions are evaluated and typical signatures derived. In the recorded signals the piercing process, the laser switch on and switch off point and waiting period are clearly resolved. To identify the cutting interruption, the signals of both Si and InGaAs diodes are high pass filtered and the signal fluctuation ranges being subsequently calculated. Introducing a correction factor, we identify that only in case of a cutting interruption the fluctuation range of the Si diode exceeds the InGaAs diode. This characteristic signature was successfully used to detect 80 cutting interruptions of 83 incomplete cuts (alpha error 3.6% and system recorded no cutting interruption from 110 faultless cuts (beta error of 0. This particularly high detection rate in combination with the easy integration of the sensor, highlight its potential for cutting interruption detection in industrial applications.

  11. Improving rooting uniformity in rose cuttings

    NARCIS (Netherlands)

    Telgen, van H.J.; Eveleens-Clark, B.A.; Garcia Victoria, N.

    2007-01-01

    Studies to improve rooting uniformity of single node stem cuttings for rose are reported. We found that the variation in shoot growth in a young rose crop depended on the variation in root number of the cuttings, which, in turn, was related to the auxin concentration applied to the cutting before

  12. Heuristic algorithms for solving of the tool routing problem for CNC cutting machines

    Science.gov (United States)

    Chentsov, P. A.; Petunin, A. A.; Sesekin, A. N.; Shipacheva, E. N.; Sholohov, A. E.

    2015-11-01

    The article is devoted to the problem of minimizing the path of the cutting tool to shape cutting machines began. This problem can be interpreted as a generalized traveling salesman problem. Earlier version of the dynamic programming method to solve this problem was developed. Unfortunately, this method allows to process an amount not exceeding thirty circuits. In this regard, the task of constructing quasi-optimal route becomes relevant. In this paper we propose options for quasi-optimal greedy algorithms. Comparison of the results of exact and approximate algorithms is given.

  13. Causal Relationships in the Balanced Scorecard: A Path Analysis Approach

    OpenAIRE

    Yael Perlman

    2013-01-01

    We use path analysis to identify causal relationships between different performance measures in each of the four perspectives defined in the balanced scorecard and examine the influence of time lag on relationships between perspectives. We analyze performance data from a real high-tech company. Our results point to a direct relationship between leading measures in the learning and growth perspective and lagging measures in the financial perspective. Our findings also support the existence of ...

  14. CPM (Critical Path Method) as a Curriculum Tool.

    Science.gov (United States)

    Mongerson, M. Duane

    This document discusses and illustrates the use of the Critical Path Method (CPM) as a tool for developing curriculum. In so doing a brief review of the evolution of CPM as a management tool developed by E. I. duPont de Nemours Company is presented. It is also noted that CPM is only a method of sequencing learning activities and not an end unto…

  15. Stochastic control with rough paths

    International Nuclear Information System (INIS)

    Diehl, Joscha; Friz, Peter K.; Gassiat, Paul

    2017-01-01

    We study a class of controlled differential equations driven by rough paths (or rough path realizations of Brownian motion) in the sense of Lyons. It is shown that the value function satisfies a HJB type equation; we also establish a form of the Pontryagin maximum principle. Deterministic problems of this type arise in the duality theory for controlled diffusion processes and typically involve anticipating stochastic analysis. We make the link to old work of Davis and Burstein (Stoch Stoch Rep 40:203–256, 1992) and then prove a continuous-time generalization of Roger’s duality formula [SIAM J Control Optim 46:1116–1132, 2007]. The generic case of controlled volatility is seen to give trivial duality bounds, and explains the focus in Burstein–Davis’ (and this) work on controlled drift. Our study of controlled rough differential equations also relates to work of Mazliak and Nourdin (Stoch Dyn 08:23, 2008).

  16. Stochastic control with rough paths

    Energy Technology Data Exchange (ETDEWEB)

    Diehl, Joscha [University of California San Diego (United States); Friz, Peter K., E-mail: friz@math.tu-berlin.de [TU & WIAS Berlin (Germany); Gassiat, Paul [CEREMADE, Université Paris-Dauphine, PSL Research University (France)

    2017-04-15

    We study a class of controlled differential equations driven by rough paths (or rough path realizations of Brownian motion) in the sense of Lyons. It is shown that the value function satisfies a HJB type equation; we also establish a form of the Pontryagin maximum principle. Deterministic problems of this type arise in the duality theory for controlled diffusion processes and typically involve anticipating stochastic analysis. We make the link to old work of Davis and Burstein (Stoch Stoch Rep 40:203–256, 1992) and then prove a continuous-time generalization of Roger’s duality formula [SIAM J Control Optim 46:1116–1132, 2007]. The generic case of controlled volatility is seen to give trivial duality bounds, and explains the focus in Burstein–Davis’ (and this) work on controlled drift. Our study of controlled rough differential equations also relates to work of Mazliak and Nourdin (Stoch Dyn 08:23, 2008).

  17. Path modeling and process control

    DEFF Research Database (Denmark)

    Høskuldsson, Agnar; Rodionova, O.; Pomerantsev, A.

    2007-01-01

    and having three or more stages. The methods are applied to a process control of a multi-stage production process having 25 variables and one output variable. When moving along the process, variables change their roles. It is shown how the methods of path modeling can be applied to estimate variables...... be performed regarding the foreseeable output property y, and with respect to an admissible range of correcting actions for the parameters of the next stage. In this paper the basic principles of path modeling is presented. The mathematics is presented for processes having only one stage, having two stages...... of the next stage with the purpose of obtaining optimal or almost optimal quality of the output variable. An important aspect of the methods presented is the possibility of extensive graphic analysis of data that can provide the engineer with a detailed view of the multi-variate variation in data....

  18. Research, Boundaries, and Policy in Networked Learning

    DEFF Research Database (Denmark)

    This book presents cutting-edge, peer reviewed research on networked learning organized by three themes: policy in networked learning, researching networked learning, and boundaries in networked learning. The "policy in networked learning" section explores networked learning in relation to policy...... networks, spaces of algorithmic governance and more. The "boundaries in networked learning" section investigates frameworks of students' digital literacy practices, among other important frameworks in digital learning. Lastly, the "research in networked learning" section delves into new research methods...

  19. NCO-5 Technician Cuts Finger while Cutting Gasket Material

    Energy Technology Data Exchange (ETDEWEB)

    Trujillo, Stanley [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Schreiber, Stephen Bruce [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mcneel, John Worth [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Monsalve-Jones, Robert A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Welsh, Mark [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ortega, Greg N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Xavier Baltazar [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Padilla, Ruby A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-12-10

    As part of the ADPSM Safety Improvement Plan, the WSST has established a subcommittee for a Learning Team. The purpose of a Learning Team is to transfer and communicate the information into operational feedback and improvement. We want to pay attention to the small things that go wrong because they are often early warning signals and may provide insight into the health of the whole system.

  20. Self-organizing path integration using a linked continuous attractor and competitive network: path integration of head direction.

    Science.gov (United States)

    Stringer, Simon M; Rolls, Edmund T

    2006-12-01

    A key issue is how networks in the brain learn to perform path integration, that is update a represented position using a velocity signal. Using head direction cells as an example, we show that a competitive network could self-organize to learn to respond to combinations of head direction and angular head rotation velocity. These combination cells can then be used to drive a continuous attractor network to the next head direction based on the incoming rotation signal. An associative synaptic modification rule with a short term memory trace enables preceding combination cell activity during training to be associated with the next position in the continuous attractor network. The network accounts for the presence of neurons found in the brain that respond to combinations of head direction and angular head rotation velocity. Analogous networks in the hippocampal system could self-organize to perform path integration of place and spatial view representations.

  1. Factorization-algebraization-path integration

    International Nuclear Information System (INIS)

    Inomata, A.; Wilson, R.

    1986-01-01

    The authors review the method of factorization proposed by Schroedinger of a quantum mechanical second-order linear differential equation into a product of two first-order differential operators, often referred to as ladder operators, as well as the modifications made to Schroedinger's method by Infeld and Hull. They then review the group theoretical treatments proposed by Miller of the Schroedinger-Infeld-Hull factorizations and go on to demonstrate the application of dynamical symmetry to path integral calculations. 30 references

  2. The path of code linting

    CERN Multimedia

    CERN. Geneva

    2017-01-01

    Join the path of code linting and discover how it can help you reach higher levels of programming enlightenment. Today we will cover how to embrace code linters to offload cognitive strain on preserving style standards in your code base as well as avoiding error-prone constructs. Additionally, I will show you the journey ahead for integrating several code linters in the programming tools your already use with very little effort.

  3. Career path for operations personnel

    International Nuclear Information System (INIS)

    Asher, J.A.

    1985-01-01

    This paper explains how selected personnel can now obtain a Bachelor of Science degree in Physics with a Nuclear Power Operations option. The program went into effect the Fall of 1984. Another program was worked out in 1982 whereby students attending the Nuclear Operators Training Program could obtain an Associates of Science degree in Mechanical Engineering Technology at the end of two years of study. This paper presents tables and charts which describe these programs and outline the career path for operators

  4. Conditionally solvable path integral problems

    International Nuclear Information System (INIS)

    Grosche, C.

    1995-05-01

    Some specific conditionally exactly solvable potentials are discussed within the path integral formalism. They generalize the usually known potentials by the incorporation of a fractional power behaviour and strongly anharmonic terms. We find four different kinds of such potentials, the first is related to the Coulomb potential, the second is an anharmonic confinement potential, and the third and the fourth are related to the Manning-Rosen potential. (orig.)

  5. Path integrals in curvilinear coordinates

    International Nuclear Information System (INIS)

    Prokhorov, L.V.

    1984-01-01

    Integration limits are studied for presenting the path integral curvilinear coordinates. For spherical (and topoloqically equivalent) coordinates it is shown that in formulas involving classical action in the exponent integration over all variables should be carried out within infinite limits. Another peculiarity is associated with appearance of the operator q which provides a complete definition of the wave functions out of the physical region. arguments are given upporting the validity of the cited statament in the general case

  6. Polygonal-path approximations on the path spaces of quantum-mechanical systems: properties of the polygonal paths

    International Nuclear Information System (INIS)

    Exner, P.; Kolerov, G.I.

    1981-01-01

    Properties of the subset of polygonal paths in the Hilbert space H of paths referring to a d-dimensional quantum-mechanical system are examined. Using the reproduction kernel technique we prove that each element of H is approximated by polygonal paths uniformly with respect to the ''norm'' of time-interval partitions. This result will be applied in the second part of the present paper to prove consistency of the uniform polygonal-path extension of the Feynman maps [ru

  7. Path Integrals in Quantum Mechanics

    International Nuclear Information System (INIS)

    Chetouani, L

    2005-01-01

    By treating path integrals the author, in this book, places at the disposal of the reader a modern tool for the comprehension of standard quantum mechanics. Thus the most important applications, such as the tunnel effect, the diffusion matrix, etc, are presented from an original point of view on the action S of classical mechanics while having it play a central role in quantum mechanics. What also emerges is that the path integral describes these applications more richly than are described traditionally by differential equations, and consequently explains them more fully. The book is certainly of high quality in all aspects: original in presentation, rigorous in the demonstrations, judicious in the choice of exercises and, finally, modern, for example in the treatment of the tunnel effect by the method of instantons. Moreover, the correspondence that exists between classical and quantum mechanics is well underlined. I thus highly recommend this book (the French version being already available) to those who wish to familiarize themselves with formulation by path integrals. They will find, in addition, interesting topics suitable for exploring further. (book review)

  8. Nonperturbative path integral expansion II

    International Nuclear Information System (INIS)

    Kaiser, H.J.

    1976-05-01

    The Feynman path integral representation of the 2-point function for a self-interacting Bose field is investigated using an expansion ('Path Integral Expansion', PIE) of the exponential of the kinetic term of the Lagrangian. This leads to a series - illustrated by a graph scheme - involving successively a coupling of more and more points of the lattice space commonly employed in the evaluation of path integrals. The values of the individual PIE graphs depend of course on the lattice constant. Two methods - Pade approximation and Borel-type extrapolation - are proposed to extract information about the continuum limit from a finite-order PIE. A more flexible PIE is possible by expanding besides the kinetic term a suitably chosen part of the interaction term too. In particular, if the co-expanded part is a mass term the calculation becomes only slightly more complicated than in the original formulation and the appearance of the graph scheme is unchanged. A significant reduction of the number of graphs and an improvement of the convergence of the PIE can be achieved by performing certain sums over an infinity of graph elements. (author)

  9. Distribution definition of path integrals

    International Nuclear Information System (INIS)

    Kerler, W.

    1979-01-01

    By starting from quantum mechanics it turns out that a rather general definition of quantum functional integrals can be given which is based on distribution theory. It applies also to curved space and provides clear rules for non-linear transformations. The refinements necessary in usual definitions of path integrals are pointed out. Since the quantum nature requires special care with time sequences, it is not the classical phase space which occurs in the phase-space form of the path integral. Feynman's configuration-space form only applies to a highly specialized situation, and therefore is not a very advantageous starting point for general investigations. It is shown that the commonly used substitutions of variables do not properly account for quantum effects. The relation to the traditional ordering problem is clarified. The distribution formulation has allowed to treat constrained systems directly at the quantum level, to complete the path integral formulation of the equivalence theorem, and to define functional integrals also for space translation after the transition to fields. (orig.)

  10. The CLEM Model: Path Analysis of the Mediating Effects of Attitudes and Motivational Beliefs on the Relationship between Perceived Learning Environment and Course Performance in an Undergraduate Non-Major Biology Course

    Science.gov (United States)

    Partin, Matthew L.; Haney, Jodi J.

    2012-01-01

    In this study, the following questions were addressed in an undergraduate non-major biology course using a large lecture format: Is there a relationship between students' perceptions of their learning environment and course performance, and what roles do motivation and attitudes play in mediating that relationship? The purpose of this study was to…

  11. Cutting costs without drawing blood.

    Science.gov (United States)

    Copeland, T

    2000-01-01

    When looking for ways to cut costs, most managers reach for the head-count hatchet, and the markets usually roar with approval. But a company can almost always create far more sustainable value by rigorously evaluating the small-ticket capital items that often get rubber-stamped. Drawing on his experience as a consultant and providing numerous anecdotes, the author contends that those "little" requests often prove to be gold plated or unnecessary. A disciplined evaluation involves asking only eight questions and conducting postmortems--regular audits of units' capital spending. But the payoff is enormous. Because cutting the capital budget increases cash flow, the author argues that a permanent cut of just 15% in the planned level of capital spending could boost some companies' market capitalization by as much as 30%. The first three questions--Is this your investment to make? Does it really have to be new? How are our competitors meeting compliance needs?--are asked of operating managers as they assemble capital project requests. The next three are asked by senior managers of themselves and their colleagues as they examine proposals: Is the left hand duplicating investments made by the right? Are trade-offs between profit and capital spending well understood? Are there signs of budget massage? At the end of the review process, senior managers ask: Are we fully using shared assets? How fine-grained are our capacity measures? The author's suggestions for the postmortem include searching for systematic problems with whole classes of expenditures and making sure audit teams come up with specific recommendations for change.

  12. Free-piston cutting machine

    Science.gov (United States)

    Ciccarelli, Gaby; Subudhi, Manomohan; Hall, Robert E.

    2000-01-01

    A cutting machine includes a gun barrel for receiving a projectile. A compression tube is disposed in flow communication with the barrel and includes a piston therein. A reservoir is disposed in flow communication with the tube and receives a first gas under pressure. A second gas fills the compression tube on a front face of the piston. And, the pressurized first gas is discharged into the tube on a back face of the piston to accelerate the piston through the tube for compressing the second gas, and in turn launching the projectile through the barrel to impact a workpiece.

  13. Clinically lean; "cutting the crap".

    Science.gov (United States)

    Caldwell, G

    2012-01-01

    Proponents of Lean Philosophy believe that successful businesses must reduce waste in working time and resources to a minimum, and maximise their use in productive work. The productive work of the Acute Medical Unit is to provide effective clinical management to a daily cohort of acutely ill patients. Many Clinicians are cynical about Lean. In this article, Dr Caldwell discusses how many clinicians complain of too much crap in the workplace, which gets in the way of swift, safe high quality clinical care. He argues that "Cutting the Crap" in the Acute Medical Unit is entirely consistent with Lean approaches to management of complex systems.

  14. Laser Cutting of Carbon Fiber Fabrics

    Science.gov (United States)

    Fuchs, A. N.; Schoeberl, M.; Tremmer, J.; Zaeh, M. F.

    Due to their high weight-specific mechanical stiffness and strength, parts made from carbon fiber reinforced polymers (CFRP) are increasingly used as structural components in the aircraft and automotive industry. However, the cutting of preforms, as with most automated manufacturing processes for CFRP components, has not yet been fully optimized. This paper discusses laser cutting, an alternative method to the mechanical cutting of preforms. Experiments with remote laser cutting and gas assisted laser cutting were carried out in order to identify achievable machining speeds. The advantages of the two different processes as well as their fitness for use in mass production are discussed.

  15. Automated Laser Cutting In Three Dimensions

    Science.gov (United States)

    Bird, Lisa T.; Yvanovich, Mark A.; Angell, Terry R.; Bishop, Patricia J.; Dai, Weimin; Dobbs, Robert D.; He, Mingli; Minardi, Antonio; Shelton, Bret A.

    1995-01-01

    Computer-controlled machine-tool system uses laser beam assisted by directed flow of air to cut refractory materials into complex three-dimensional shapes. Velocity, position, and angle of cut varied. In original application, materials in question were thermally insulating thick blankets and tiles used on space shuttle. System shapes tile to concave or convex contours and cuts beveled edges on blanket, without cutting through outer layer of quartz fabric part of blanket. For safety, system entirely enclosed to prevent escape of laser energy. No dust generated during cutting operation - all material vaporized; larger solid chips dislodged from workpiece easily removed later.

  16. Rooting of stem cuttings of ixora

    Directory of Open Access Journals (Sweden)

    Aline De Souza Silva

    2015-08-01

    Full Text Available The ixora is ornamental plant widely used in landscaping. In order to maximize the propagation of cuts, we evaluated the concentrations of auxin (indolbutiric acid and the presence of leaves on the rooting in cuts of Ixora coccinea L. The experiment was conducted in randomized block design, in factorial design 3x4, with three types of cuts (without leaf, with two or four leaves, four concentrations of indolbutiric acid (0, 1000, 2000 and 4000 mg L-1, with four replications and 10 cuts in each experimental unit. After 53 days of implantation the experiment, evaluated the survival(%, rooting(%, sprouting(%, formation of callus(%, number, length and biomass of roots formed. The interaction of the type of cuts with concentrations of auxin was not significant for any of the variables analyzed. The survival of cuttings was not influenced by the treatments. Cuts with two or four leaves presented rooting and length of roots above the cuttings without leaves. The application of auxin does not substitute the presence of leaf in cuts of ixora in vegetative propagation. The vegetative propagation by cut of ixora can be made without application of auxin, and the leaves must be maintained in the cuttings.

  17. Cutting method and cutting device for spent fuel rod of nuclear reactor

    International Nuclear Information System (INIS)

    Komatsu, Masahiko; Ose, Toshihiko.

    1996-01-01

    A control rod transferred under water in a vertically suspended state is postured horizontally at such a water depth that radiations can be shielded, and then it is cut to a dropping speed limiting portion and a cross-like main body. The separated cross-like main body portion is further cut in the longitudinal direction and separated into a pair of cut pieces each having an L-shaped cross section. A disk like metal saw is used as a cutting tool. Alternatively, a plasma jet cutter or a melting-type water jet cutter is used as a cutting tool. Then, since the spent control rod to be cut is postured horizontally under water, the water depth for the cutting position can be reduced. As a result, the cutting state using the cutting tool can be observed by naked eyes from the position above the water surface thereby enabling to perform the cutting operation reliably. (N.H.)

  18. Cooperative path planning of unmanned aerial vehicles

    CERN Document Server

    Tsourdos, Antonios; Shanmugavel, Madhavan

    2010-01-01

    An invaluable addition to the literature on UAV guidance and cooperative control, Cooperative Path Planning of Unmanned Aerial Vehicles is a dedicated, practical guide to computational path planning for UAVs. One of the key issues facing future development of UAVs is path planning: it is vital that swarm UAVs/ MAVs can cooperate together in a coordinated manner, obeying a pre-planned course but able to react to their environment by communicating and cooperating. An optimized path is necessary in order to ensure a UAV completes its mission efficiently, safely, and successfully. Focussing on the path planning of multiple UAVs for simultaneous arrival on target, Cooperative Path Planning of Unmanned Aerial Vehicles also offers coverage of path planners that are applicable to land, sea, or space-borne vehicles. Cooperative Path Planning of Unmanned Aerial Vehicles is authored by leading researchers from Cranfield University and provides an authoritative resource for researchers, academics and engineers working in...

  19. Electron Inelastic-Mean-Free-Path Database

    Science.gov (United States)

    SRD 71 NIST Electron Inelastic-Mean-Free-Path Database (PC database, no charge)   This database provides values of electron inelastic mean free paths (IMFPs) for use in quantitative surface analyses by AES and XPS.

  20. Time optimal paths for high speed maneuvering

    Energy Technology Data Exchange (ETDEWEB)

    Reister, D.B.; Lenhart, S.M.

    1993-01-01

    Recent theoretical results have completely solved the problem of determining the minimum length path for a vehicle with a minimum turning radius moving from an initial configuration to a final configuration. Time optimal paths for a constant speed vehicle are a subset of the minimum length paths. This paper uses the Pontryagin maximum principle to find time optimal paths for a constant speed vehicle. The time optimal paths consist of sequences of axes of circles and straight lines. The maximum principle introduces concepts (dual variables, bang-bang solutions, singular solutions, and transversality conditions) that provide important insight into the nature of the time optimal paths. We explore the properties of the optimal paths and present some experimental results for a mobile robot following an optimal path.

  1. Classical and quantum dynamics from classical paths to path integrals

    CERN Document Server

    Dittrich, Walter

    2016-01-01

    Graduate students who want to become familiar with advanced computational strategies in classical and quantum dynamics will find here both the fundamentals of a standard course and a detailed treatment of the time-dependent oscillator, Chern-Simons mechanics, the Maslov anomaly and the Berry phase, to name a few. Well-chosen and detailed examples illustrate the perturbation theory, canonical transformations, the action principle and demonstrate the usage of path integrals. This new edition has been revised and enlarged with chapters on quantum electrodynamics, high energy physics, Green’s functions and strong interaction.

  2. Path Integral Formulation of Anomalous Diffusion Processes

    OpenAIRE

    Friedrich, Rudolf; Eule, Stephan

    2011-01-01

    We present the path integral formulation of a broad class of generalized diffusion processes. Employing the path integral we derive exact expressions for the path probability densities and joint probability distributions for the class of processes under consideration. We show that Continuous Time Random Walks (CTRWs) are included in our framework. A closed expression for the path probability distribution of CTRWs is found in terms of their waiting time distribution as the solution of a Dyson ...

  3. Chemical scissors cut phosphorene nanostructures

    International Nuclear Information System (INIS)

    Peng, Xihong; Wei, Qun

    2014-01-01

    Phosphorene, a recently fabricated two-dimensional puckered honeycomb structure of phosphorus, showed promising properties for applications in nano-electronics. In this work, we report a chemical scissors effect on phosphorene, using first-principles method. It was found that chemical species, such as H, OH, F, and Cl, can act as scissors to cut phosphorene. Phosphorus nanochains and nanoribbons can be obtained. The scissors effect results from the strong bonding between the chemical species and phosphorus atoms. Other species such as O, S and Se fail to cut phosphorene nanostructures due to their weak bonding with phosphorus. The electronic structures of the produced P-chains reveal that the hydrogenated chain is an insulator while the pristine chain is a one-dimensional Dirac material, in which the charge carriers are massless fermions travelling at an effective speed of light ∼8 × 10 5 m s −1 . The obtained zigzag phosphorene nanoribbons show either metallic or semiconducting behaviors, depending on the treatment of the edge phosphorus atoms. (paper)

  4. The center-cut solution.

    Science.gov (United States)

    Firnstahl, T W

    1993-01-01

    Timothy Firnstahl owns five successful restaurants in Seattle, but he recently came very close to owning none. In the early 1990s, he found himself, like so many restauranteurs, facing rising costs, inefficient management, and a recession. Confronting financial annihilation, Firnstahl had to act quickly: since he had no peripherals to trim, he cut off the head of his company. Remarkably, it worked. Firnstahl's problem was his new and innovative restaurant, Sharps Fresh Roasting. The heart of the Sharps concept was a unique long-roasting technique that made lean, inexpensive meats taste as juicy and delicious as fattier, expensive cuts. The process also lent itself to faster service and lower labor costs. But it wasn't working. Sharps wasn't breaking even, and his other restaurants couldn't make up the difference. He needed a solution fast. Firnstahl got his answer from Mikhail Gorbachev: slash the centralized command and liberate the company. In doing so, he would also transfer virtually all power and responsibility to his line managers. And after five months of intensive study and planning, he accomplished what he set out to do. He fired most of his corporate staff, empowered his restaurant managers with "100% Power and Responsibility," and, finally, undertook a massive promotion campaign. A year later, Sharps Fresh Roasting is the gold mine Firnstahl always believed it could be. He's done away with bureaucracy and turned business around in a down market. All this because his managers are managing themselves.

  5. Unzip instabilities: Straight to oscillatory transitions in the cutting of thin polymer sheets

    Science.gov (United States)

    Reis, P. M.; Kumar, A.; Shattuck, M. D.; Roman, B.

    2008-06-01

    We report an experimental investigation of the cutting of a thin brittle polymer sheet with a blunt tool. It was recently shown that the fracture path becomes oscillatory when the tool is much wider than the sheet thickness. Here we uncover two novel transitions from straight to oscillatory fracture by varying either the tilt angle of the tool or the speed of cutting, respectively. We denote these by angle and speed unzip instabilities and analyze them by quantifying both the dynamics of the crack tip and the final shapes of the fracture paths. Moreover, for the speed unzip instability, the straight crack lip obtained at low speeds exhibits out-of-plane buckling undulations (as opposed to being flat above the instability threshold) suggesting a transition from ductile to brittle fracture.

  6. A branch-and-cut-and-price approach for the pickup and delivery problem with shuttle routes

    DEFF Research Database (Denmark)

    Masson, Renaud; Røpke, Stefan; Lehuédé, Fabien

    2014-01-01

    for the PDPS and a branch-and-cut-and-price algorithm to solve it. The pricing sub-problem, an Elementary Shortest Path Problem with Resource Constraints (ESPPRC), is solved with a labeling algorithm enhanced with efficient dominance rules. Three families of valid inequalities are used to strengthen...

  7. Partial Path Column Generation for the ESPPRC

    DEFF Research Database (Denmark)

    Jepsen, Mads Kehlet; Petersen, Bjørn

    This talk introduces a decomposition of the Elementary Shortest Path Problem with Resource Constraints(ESPPRC), where the path is combined by smaller sub paths. We show computational result by comparing different approaches for the decomposition and compare the best of these with existing algorit...

  8. Strain path dependency in metal plasticity

    NARCIS (Netherlands)

    Viatkina, E.M.; Brekelmans, W.A.M.; Geers, M.G.D.

    2003-01-01

    A change in strain path has a significant effect on the mechanical response of metals. Strain path change effects physically originate from a complex microstructure evolution. This paper deals with the contribution of cell structure evolution to the strain path change effect. The material with cells

  9. STRUCTURAL ANNOTATION OF EM IMAGES BY GRAPH CUT

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Hang; Auer, Manfred; Parvin, Bahram

    2009-05-08

    Biological images have the potential to reveal complex signatures that may not be amenable to morphological modeling in terms of shape, location, texture, and color. An effective analytical method is to characterize the composition of a specimen based on user-defined patterns of texture and contrast formation. However, such a simple requirement demands an improved model for stability and robustness. Here, an interactive computational model is introduced for learning patterns of interest by example. The learned patterns bound an active contour model in which the traditional gradient descent optimization is replaced by the more efficient optimization of the graph cut methods. First, the energy function is defined according to the curve evolution. Next, a graph is constructed with weighted edges on the energy function and is optimized with the graph cut algorithm. As a result, the method combines the advantages of the level set method and graph cut algorithm, i.e.,"topological" invariance and computational efficiency. The technique is extended to the multi-phase segmentation problem; the method is validated on synthetic images and then applied to specimens imaged by transmission electron microscopy(TEM).

  10. Space charge models and PATH

    International Nuclear Information System (INIS)

    Wald, H.B.

    1990-01-01

    The 'PATH' codes are used to design magnetic optics subsystems for neutral particle beam systems. They include a 2-1/2D and three 3-D space charge models, two of which have recently been added. This paper describes the 3-D models and reports on preliminary benchmark studies in which these models are checked for stability as the cloud size is varied and for consistency with each other. Differences between the models are investigated and the computer time requirements for running these models are established

  11. Innovation paths in wind power

    DEFF Research Database (Denmark)

    Lema, Rasmus; Nordensvärd, Johan; Urban, Frauke

    Denmark and Germany both make substantial investments in low carbon innovation, not least in the wind power sector. These investments in wind energy are driven by the twin objectives of reducing carbon emissions and building up international competitive advantage. Support for wind power dates back....... The ‘Danish Design’ remains the global standard. The direct drive design, while uncommon in Denmark, dominates the German installation base. Direct drive technology has thus emerged as a distinctly German design and sub-trajectory within the overall technological innovation path. When it comes to organising...... global interconnectedness of wind technology markets and the role of emerging new players, such as China and India....

  12. Uncommon paths in quantum physics

    CERN Document Server

    Kazakov, Konstantin V

    2014-01-01

    Quantum mechanics is one of the most fascinating, and at the same time most controversial, branches of contemporary science. Disputes have accompanied this science since its birth and have not ceased to this day. Uncommon Paths in Quantum Physics allows the reader to contemplate deeply some ideas and methods that are seldom met in the contemporary literature. Instead of widespread recipes of mathematical physics, based on the solutions of integro-differential equations, the book follows logical and partly intuitional derivations of non-commutative algebra. Readers can directly penetrate the

  13. Fiscal Policy Trends: The Path to Balance or the Road to Ruin?

    Directory of Open Access Journals (Sweden)

    Bev Dahlby

    2018-03-01

    Full Text Available The NDP government’s plan to balance the provincial budget by 2023-24 is based on drastically cutting capital spending and on optimistic revenue projections. In order to show that these are the key elements of the “Path to Balance”, we need to know how interest payments on debt, total operating expenditures, and the cash deficits will evolve under the government’s plan, but these key fiscal variables are not reported in the budget documents.

  14. Welding Robot Collision-Free Path Optimization

    Directory of Open Access Journals (Sweden)

    Xuewu Wang

    2017-02-01

    Full Text Available Reasonable welding path has a significant impact on welding efficiency, and a collision-free path should be considered first in the process of welding robot path planning. The shortest path length is considered as an optimization objective, and obstacle avoidance is considered as the constraint condition in this paper. First, a grid method is used as a modeling method after the optimization objective is analyzed. For local collision-free path planning, an ant colony algorithm is selected as the search strategy. Then, to overcome the shortcomings of the ant colony algorithm, a secondary optimization is presented to improve the optimization performance. Finally, the particle swarm optimization algorithm is used to realize global path planning. Simulation results show that the desired welding path can be obtained based on the optimization strategy.

  15. Effects of Optimizing the Scan-Path on Scanning Keyboards with QWERTY-Layout for English Text.

    Science.gov (United States)

    Sandnes, Frode Eika; Medola, Fausto Orsi

    2017-01-01

    Scanning keyboards can be essential tools for individuals with reduced motor function. However, most research addresses layout optimization. Learning new layouts is time-consuming. This study explores the familiar QWERTY layout with alternative scanning paths intended for English text. The results show that carefully designed scan-paths can help QWERTY nearly match optimized layouts in performance.

  16. Path integration of head direction: updating a packet of neural activity at the correct speed using axonal conduction delays.

    Science.gov (United States)

    Walters, Daniel; Stringer, Simon; Rolls, Edmund

    2013-01-01

    The head direction cell system is capable of accurately updating its current representation of head direction in the absence of visual input. This is known as the path integration of head direction. An important question is how the head direction cell system learns to perform accurate path integration of head direction. In this paper we propose a model of velocity path integration of head direction in which the natural time delay of axonal transmission between a linked continuous attractor network and competitive network acts as a timing mechanism to facilitate the correct speed of path integration. The model effectively learns a "look-up" table for the correct speed of path integration. In simulation, we show that the model is able to successfully learn two different speeds of path integration across two different axonal conduction delays, and without the need to alter any other model parameters. An implication of this model is that, by learning look-up tables for each speed of path integration, the model should exhibit a degree of robustness to damage. In simulations, we show that the speed of path integration is not significantly affected by degrading the network through removing a proportion of the cells that signal rotational velocity.

  17. New Modelling Strategies For Metal Cutting

    International Nuclear Information System (INIS)

    Rosa, Pedro A. R.; Martins, Paulo A. F.; Atkins, Anthony G.

    2007-01-01

    This paper draws from the 'plasticity and friction only' view of metal cutting to the presentation of new modelling strategies based on the interaction between finite elements and modern ductile fracture mechanics. The overall presentation is supported by specially designed orthogonal metal cutting experiments that were performed on Lead test specimens under laboratory-controlled conditions. Comparisons between theoretical predictions and experimental results comprise a wide range of topics such as material flow, cutting forces and specific cutting pressure. The paper demonstrates that while material flow and chip formation can be successfully modelled by traditional 'plasticity and friction only' analyses, the contribution of the fracture work involved in the formation of new surfaces is essential for obtaining good estimates of cutting forces and of the specific cutting pressure

  18. Laser cutting of sheets for Tailored Blanks

    DEFF Research Database (Denmark)

    Bagger, Claus; Olsen, Flemming Ove

    1999-01-01

    sound welds. Laser cutting the sheets may therefore be an alternative to shear cutting, if the cut kerf squareness can be kept below 0.05 mm.In a number of systematic laboratory experiments the effects of the major process parameters in laser cutting have been investigated. Each cut was quantified...... by the squareness, the surface roughness and the burr height. Mild steel as well as high strength steel with and with out galvanisation with thickness' of 0.7(5) and 1.25 were used.In the tests the difference in cut quality between a 5" and a 7.5" focusing lens were tested and the effect of using pulsed mode laser...

  19. Method of dismantling cylindrical structure by cutting

    International Nuclear Information System (INIS)

    Harada, Minoru; Mitsuo, Kohei; Yokota, Isoya; Nakamura, Kenjiro.

    1989-01-01

    This invention concerns a method of cutting and removing cylindrical structures, for example, iron-reinforced concrete materials such as thermal shielding walls in BWR type power plants into block-like form. That is, in a method of cutting and removing the cylindrical structure from the side of the outer wall, the structural material is cut from above to below successively in the axial direction and the circumferential direction by means abrasive jet by remote operation and cut into blocks each of a predetermined size. The cut out blocks are successively taken out. Cutting of the material from above to below by remote operation and taking out of small blocks causes no hazards to human body. Upon practicing the present invention, it is preferred to use a processing device for slurry and exhaust gases for preventing scattering of activated dismantled pieces or powdery dusts. (K.M.)

  20. Submerged cutting characteristics of abrasive suspension jet

    International Nuclear Information System (INIS)

    Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroki

    2015-01-01

    An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

  1. Craterlike structures on the laser cut surface

    Science.gov (United States)

    Shulyatyev, V. B.; Orishich, A. M.

    2017-10-01

    Analysis of the laser cut surface morphology remain topical. It is related with the fact that the surface roughness is the main index of the cut quality. The present paper deals with the experimental study of the relatively unstudied type of defects on the laser cut surface, dimples, or craters. According to the measurement results, amount of craters per unit of the laser cut surface area rises as the sheet thickness rises. The crater diameter rises together with the sheet thickness and distance from the upper sheet edge. The obtained data permit concluding that the defects like craters are observed predominantly in the case of thick sheets. The results agree with the hypothesis of crater formation as impact structures resulting from the melt drops getting on the cut channel walls upon separation from the cut front by the gas flow.

  2. Testing a Conception of How School Leadership Influences Student Learning

    Science.gov (United States)

    Leithwood, Kenneth; Patten, Sarah; Jantzi, Doris

    2010-01-01

    Purpose: This article describes and reports the results of testing a new conception of how leadership influences student learning ("The Four Paths"). Framework: Leadership influence is conceptualized as flowing along four paths (Rational, Emotions, Organizational, and Family) toward student learning. Each path is populated by multiple…

  3. Laser-generated ultrasound for high-precision cutting of tissue-mimicking gels (Conference Presentation)

    Science.gov (United States)

    Lee, Taehwa; Luo, Wei; Li, Qiaochu; Guo, L. Jay

    2017-03-01

    Laser-generated focused ultrasound has shown great promise in precisely treating cells and tissues by producing controlled micro-cavitation within the acoustic focal volume (30 MPa, negative pressure amplitude). By moving cavitation spots along pre-defined paths through a motorized stage, tissue-mimicking gels of different elastic moduli were cut into different shapes (rectangle, triangle, and circle), leaving behind the same shape of holes, whose sizes are less than 1 mm. The cut line width is estimated to be less than 50 um (corresponding to localized cavitation region), allowing for accurate cutting. This novel approach could open new possibility for in-vivo treatment of diseased tissues in a high-precision manner (i.e., high-precision invisible sonic scalpel).

  4. Integral transforms of the quantum mechanical path integral: Hit function and path-averaged potential

    Science.gov (United States)

    Edwards, James P.; Gerber, Urs; Schubert, Christian; Trejo, Maria Anabel; Weber, Axel

    2018-04-01

    We introduce two integral transforms of the quantum mechanical transition kernel that represent physical information about the path integral. These transforms can be interpreted as probability distributions on particle trajectories measuring respectively the relative contribution to the path integral from paths crossing a given spatial point (the hit function) and the likelihood of values of the line integral of the potential along a path in the ensemble (the path-averaged potential).

  5. Classical and quantum dynamics from classical paths to path integrals

    CERN Document Server

    Dittrich, Walter

    2017-01-01

    Graduate students who wish to become familiar with advanced computational strategies in classical and quantum dynamics will find in this book both the fundamentals of a standard course and a detailed treatment of the time-dependent oscillator, Chern-Simons mechanics, the Maslov anomaly and the Berry phase, to name just a few topics. Well-chosen and detailed examples illustrate perturbation theory, canonical transformations and the action principle, and demonstrate the usage of path integrals. The fifth edition has been revised and enlarged to include chapters on quantum electrodynamics, in particular, Schwinger’s proper time method and the treatment of classical and quantum mechanics with Lie brackets and pseudocanonical transformations. It is shown that operator quantum electrodynamics can be equivalently described with c-numbers, as demonstrated by calculating the propagation function for an electron in a prescribed classical electromagnetic field.

  6. Ceramic cutting tools materials, development and performance

    CERN Document Server

    Whitney, E Dow

    1994-01-01

    Interest in ceramics as a high speed cutting tool material is based primarily on favorable material properties. As a class of materials, ceramics possess high melting points, excellent hardness and good wear resistance. Unlike most metals, hardness levels in ceramics generally remain high at elevated temperatures which means that cutting tip integrity is relatively unaffected at high cutting speeds. Ceramics are also chemically inert against most workmetals.

  7. CAD for cutting head exchange of roadheader

    Energy Technology Data Exchange (ETDEWEB)

    Tao, Z.; Wu, Z.; Qian, P. [China Coal Research Institute (China). Shanghai Branch

    1999-08-01

    Improving the cutting method according to the actual operating conditions is an effective way to raise production efficiency. A cutting head designed by means of computer and CAD software is characterized by short design cycle but high design quality. Taking the AM-50 road header as an example, this paper shows that it is feasible to design an interchangeable cutting head for the machine without interfering with the main technical parameters. 2 refs., 5 figs., 1 tab.

  8. Pain Relief for Budget Cuts.

    Science.gov (United States)

    Fultz, David A.

    1983-01-01

    The Grand Blanc (Michigan) Community School District sets budget priorities by (1) surveying students, taxpayers, and teachers to learn their preferences for current programs and services; (2) determining the costs of state-mandated programs; (3) listing nonmandated programs and determining their costs; and (4) considering proposed new programs.…

  9. Student Energy Cuts Heat Loss.

    Science.gov (United States)

    Sirote, Patrice J.

    1981-01-01

    Under the skilled supervision of a master carpenter hired to direct this Comprehensive Employment and Training Act project, seven high school students and two beginning workers are learning the varied and complex skills of building maintenance, renewing their city's schools, and bringing home a badly needed paycheck. (LRA)

  10. Underwater laser cutting of metallic structures

    International Nuclear Information System (INIS)

    Alfille, J.P.; Schildknecht, J.; Ramaswami, V.S.

    1993-01-01

    In the frame of an european contract, the feasibility of the underwater cutting with a CO 2 laser power is studied. The aim of this work is the dismantling metallic structures of reactors pools. The paper analyzes the general concept of the experimental device, the underwater cutting head, the experimenting vessel, examples of cuttings in dismantling situation with a 500 W CO 2 laser, and examples of cuttings with a 5 kW CO 2 laser. (author). 2 refs., 9 figs., 2 tabs

  11. Underwater laser cutting of metal structures

    Energy Technology Data Exchange (ETDEWEB)

    Alfille, J.P.; Prunele, D. de [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Direction des Technologies Avancees; Pilot, G. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Dept. de Protection de l`Environnement et des Installations; Fredrick, P.; Ramaswami, V.S.; Muys, P. [Radius Engineering, Gent (Belgium)

    1994-12-31

    Cutting tests were carried out on stainless steel (304L) in air and under 7 meters of water (application to reactor pools), using CO{sub 2} and YAG lasers; results concerned cutting speed, quality of cut, cutting thickness. By-products of sectioning operations using a CO{sub 2} laser were studied: dross, aerosols, suspended particles in water, gas analysis, chemical analysis of the aerosols. Same measurements are currently being taken in the case of the YAG laser with beam transported via optical fiber. (from author). 16 figs., 2 tabs., 3 refs.

  12. Underwater laser cutting of metal structures

    International Nuclear Information System (INIS)

    Alfille, J.P.; Prunele, D. de

    1994-01-01

    Cutting tests were carried out on stainless steel (304L) in air and under 7 meters of water (application to reactor pools), using CO 2 and YAG lasers; results concerned cutting speed, quality of cut, cutting thickness. By-products of sectioning operations using a CO 2 laser were studied: dross, aerosols, suspended particles in water, gas analysis, chemical analysis of the aerosols. Same measurements are currently being taken in the case of the YAG laser with beam transported via optical fiber. (from author). 16 figs., 2 tabs., 3 refs

  13. A cutting force model for micromilling applications

    DEFF Research Database (Denmark)

    Bissacco, Giuliano; Hansen, Hans Nørgaard; De Chiffre, Leonardo

    2006-01-01

    In micro milling the maximum uncut chip thickness is often smaller than the cutting edge radius. This paper introduces a new cutting force model for ball nose micro milling that is capable of taking into account the effect of the edge radius.......In micro milling the maximum uncut chip thickness is often smaller than the cutting edge radius. This paper introduces a new cutting force model for ball nose micro milling that is capable of taking into account the effect of the edge radius....

  14. The Effects of Students' Learning Anxiety and Motivation on the Learning Achievement in the Activity Theory Based Gamified Learning Environment

    Science.gov (United States)

    Su, Chung-Ho

    2017-01-01

    The advancement of mobile game-based learning has encouraged many related studies, which has enabled students to learn more and faster. To enhance the clinical path of cardiac catheterization learning, this paper has developed a mobile 3D-CCGBLS (3D Cardiac Catheterization Game-Based Learning System) with a learning assessment for cardiac…

  15. Integrated assignment and path planning

    Science.gov (United States)

    Murphey, Robert A.

    2005-11-01

    A surge of interest in unmanned systems has exposed many new and challenging research problems across many fields of engineering and mathematics. These systems have the potential of transforming our society by replacing dangerous and dirty jobs with networks of moving machines. This vision is fundamentally separate from the modern view of robotics in that sophisticated behavior is realizable not by increasing individual vehicle complexity, but instead through collaborative teaming that relies on collective perception, abstraction, decision making, and manipulation. Obvious examples where collective robotics will make an impact include planetary exploration, space structure assembly, remote and undersea mining, hazardous material handling and clean-up, and search and rescue. Nonetheless, the phenomenon driving this technology trend is the increasing reliance of the US military on unmanned vehicles, specifically, aircraft. Only a few years ago, following years of resistance to the use of unmanned systems, the military and civilian leadership in the United States reversed itself and have recently demonstrated surprisingly broad acceptance of increasingly pervasive use of unmanned platforms in defense surveillance, and even attack. However, as rapidly as unmanned systems have gained acceptance, the defense research community has discovered the technical pitfalls that lie ahead, especially for operating collective groups of unmanned platforms. A great deal of talent and energy has been devoted to solving these technical problems, which tend to fall into two categories: resource allocation of vehicles to objectives, and path planning of vehicle trajectories. An extensive amount of research has been conducted in each direction, yet, surprisingly, very little work has considered the integrated problem of assignment and path planning. This dissertation presents a framework for studying integrated assignment and path planning and then moves on to suggest an exact

  16. Eyes On the Ground: Path Forward Analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Brost, Randolph; Little, Charles Q.; peter-stein, natacha; Wade, James Rokwel

    2018-03-01

    A previous report assesses our progress to date on the Eyes On the Ground project, and reviews lessons learned [1]. In this report, we address the implications of those lessons in defining the most productive path forward for the remainder of the project. We propose two main concepts: Interactive Diagnosis and Model-Driven Assistance. Among these, the Model-Driven Assistance concept appears the most promising. The Model-Driven Assistance concept is based on an approximate but useful model of a facility, which provides a unified representation for storing, viewing, and analyzing data that is known about the facility. This representation provides value to both inspectors and IAEA headquarters, and facilitates communication between the two. The concept further includes a lightweight, portable field tool to aid the inspector in executing a variety of inspection tasks, including capture of images and 3-d scan data. We develop a detailed description of this concept, including its system components, functionality, and example use cases. The envisioned tool would provide value by reducing inspector cognitive load, streamlining inspection tasks, and facilitating communication between the inspector and teams at IAEA headquarters. We conclude by enumerating the top implementation priorities to pursue in the remaining limited time of the project. Approved for public release; further dissemination unlimited.

  17. Estimating a path through a map of decision making.

    Directory of Open Access Journals (Sweden)

    William A Brock

    Full Text Available Studies of the evolution of collective behavior consider the payoffs of individual versus social learning. We have previously proposed that the relative magnitude of social versus individual learning could be compared against the transparency of payoff, also known as the "transparency" of the decision, through a heuristic, two-dimensional map. Moving from west to east, the estimated strength of social influence increases. As the decision maker proceeds from south to north, transparency of choice increases, and it becomes easier to identify the best choice itself and/or the best social role model from whom to learn (depending on position on east-west axis. Here we show how to parameterize the functions that underlie the map, how to estimate these functions, and thus how to describe estimated paths through the map. We develop estimation methods on artificial data sets and discuss real-world applications such as modeling changes in health decisions.

  18. Evaluation of the Learning Process of Students Reinventing the General Law of Energy Conservation

    Science.gov (United States)

    Logman, Paul; Kaper, Wolter; Ellermeijer, Ton

    2015-01-01

    To investigate the relationship between context and concept we have constructed a conceptual learning path in which students reinvent the concept of energy conservation and embedded this path in two authentic practices. A comparison of the expected learning outcome with actual student output for the most important steps in the learning path gives…

  19. Path Creation, Path Dependence and Breaking Away from the Path: Re-Examining the Case of Nokia

    OpenAIRE

    Wang, Jens; Hedman, Jonas; Tuunainen, Virpi Kristiina

    2016-01-01

    The explanation of how and why firms succeed or fail is a recurrent research challenge. This is particularly important in the context of technological innovations. We focus on the role of historical events and decisions in explaining such success and failure. Using a case study of Nokia, we develop and extend a multi-layer path dependence framework. We identify four layers of path dependence: technical, strategic and leadership, organizational, and external collaboration. We show how path dep...

  20. Test on the effectiveness of the sum over paths approach in favoring the construction of an integrated knowledge of quantum physics in high school

    Directory of Open Access Journals (Sweden)

    Massimiliano Malgieri

    2017-01-01

    Full Text Available In this paper we present the results of a research-based teaching-learning sequence on introductory quantum physics based on Feynman’s sum over paths approach in the Italian high school. Our study focuses on students’ understanding of two founding ideas of quantum physics, wave particle duality and the uncertainty principle. In view of recent research reporting the fragmentation of students’ mental models of quantum concepts after initial instruction, we collected and analyzed data using the assessment tools provided by knowledge integration theory. Our results on the group of n=14 students who performed the final test indicate that the functional explanation of wave particle duality provided by the sum over paths approach may be effective in leading students to build consistent mental models of quantum objects, and in providing them with a unified perspective on both the photon and the electron. Results on the uncertainty principle are less clear cut, as the improvements over traditional instruction appear less significant. Given the low number of students in the sample, this work should be interpreted as a case study, and we do not attempt to draw definitive conclusions. However, our study suggests that (i the sum over paths approach may deserve more attention from researchers and educators as a possible route to introduce basic concepts of quantum physics in high school, and (ii more research should be focused not only on the correctness of students’ mental models on individual concepts, but also on the ability of students to connect different ideas and experiments related to quantum theory in an organized whole.

  1. Rainbow paths with prescribed ends

    DEFF Research Database (Denmark)

    Alishahi, Meysam; Taherkhani, Ali; Thomassen, Carsten

    2011-01-01

    vertices. We also prove that every connected graph with atleast one edge has a proper k-coloring (for some k) such that every vertex of color i has a neighbor of color i + 1 (mod k). C-5 shows that k may have to be greater than the chromatic number. However, if the graph is connected, infinite and locally...... finite, and has finite chromatic number, then the k-coloring exists for every k >= chi(G). In fact, the k-coloring can be chosen such that every vertex is a starting vertex of an infinite path such that the color increases by 1 (mod k) along each edge. The method is based on the circular chromatic number...... chi(c)(G). In particular, we verify the above conjecture for all connected graphs whose circular chromatic number equals the chromatic number....

  2. Counting paths with Schur transitions

    Energy Technology Data Exchange (ETDEWEB)

    Díaz, Pablo [Department of Physics and Astronomy, University of Lethbridge, Lethbridge, Alberta, T1K 3M4 (Canada); Kemp, Garreth [Department of Physics, University of Johannesburg, P.O. Box 524, Auckland Park 2006 (South Africa); Véliz-Osorio, Alvaro, E-mail: aveliz@gmail.com [Mandelstam Institute for Theoretical Physics, University of the Witwatersrand, WITS 2050, Johannesburg (South Africa); School of Physics and Astronomy, Queen Mary, University of London, Mile End Road, London E1 4NS (United Kingdom)

    2016-10-15

    In this work we explore the structure of the branching graph of the unitary group using Schur transitions. We find that these transitions suggest a new combinatorial expression for counting paths in the branching graph. This formula, which is valid for any rank of the unitary group, reproduces known asymptotic results. We proceed to establish the general validity of this expression by a formal proof. The form of this equation strongly hints towards a quantum generalization. Thus, we introduce a notion of quantum relative dimension and subject it to the appropriate consistency tests. This new quantity finds its natural environment in the context of RCFTs and fractional statistics; where the already established notion of quantum dimension has proven to be of great physical importance.

  3. Aircraft Engine Gas Path Diagnostic Methods: Public Benchmarking Results

    Science.gov (United States)

    Simon, Donald L.; Borguet, Sebastien; Leonard, Olivier; Zhang, Xiaodong (Frank)

    2013-01-01

    Recent technology reviews have identified the need for objective assessments of aircraft engine health management (EHM) technologies. To help address this issue, a gas path diagnostic benchmark problem has been created and made publicly available. This software tool, referred to as the Propulsion Diagnostic Method Evaluation Strategy (ProDiMES), has been constructed based on feedback provided by the aircraft EHM community. It provides a standard benchmark problem enabling users to develop, evaluate and compare diagnostic methods. This paper will present an overview of ProDiMES along with a description of four gas path diagnostic methods developed and applied to the problem. These methods, which include analytical and empirical diagnostic techniques, will be described and associated blind-test-case metric results will be presented and compared. Lessons learned along with recommendations for improving the public benchmarking processes will also be presented and discussed.

  4. Technology development for cutting a reactor pressure vessel using a mechanical cutting technique

    International Nuclear Information System (INIS)

    Watanabe, Masaaki; Miyasaka, Yasuhiko; Miyao, Hidehiko; Ooki, Arahiko; Ninomiya, Toshiaki; Koiwai, Masami

    2001-01-01

    On decommissioning of nuclear facilities, the thermal cutting technique such as an oxygen-acetylene gas cutting and a plasma arc cutting are generally used for cutting massive and thick steel structures in consideration with cutting speed and control performance. These techniques generate dust, smoke, aerosol and a large quantity of secondary waste. Mechanical cutting technique has an advantage of small amount of secondary waste, and the metal chips from the kerf recovered easily compared with these thermal cutting technique. The remote mechanical cutting system for highly activated RPV has been developed with the manner which achieves the safety and cost effectiveness. The development has been performed on consignment to RANDEC from the Science and Technology Agency of Japan. (author)

  5. Selection of Near Optimal Laser Cutting Parameters in CO2 Laser Cutting by the Taguchi Method

    Directory of Open Access Journals (Sweden)

    Miloš MADIĆ

    2013-12-01

    Full Text Available Identification of laser cutting conditions that are insensitive to parameter variations and noise is of great importance. This paper demonstrates the application of Taguchi method for optimization of surface roughness in CO2 laser cutting of stainless steel. The laser cutting experiment was planned and conducted according to the Taguchi’s experimental design using the L27 orthogonal array. Four laser cutting parameters such as laser power, cutting speed, assist gas pressure, and focus position were considered in the experiment. Using the analysis of means and analysis of variance, the significant laser cutting parameters were identified, and subsequently the optimal combination of laser cutting parameter levels was determined. The results showed that the cutting speed is the most significant parameter affecting the surface roughness whereas the influence of the assist gas pressure can be neglected. It was observed, however, that interaction effects have predominant influence over the main effects on the surface roughness.

  6. Experimental research on the durability cutting tools for cutting-off steel profiles

    Directory of Open Access Journals (Sweden)

    Cristea Alexandru

    2017-01-01

    Full Text Available The production lines used for manufacturing U-shaped profiles are very complex and they must have high productivity. One of the most important stages of the fabrication process is the cutting-off. This paper presents the experimental research and analysis of the durability of the cutting tools used for cutting-off U-shaped metal steel profiles. The results of this work can be used to predict the durability of the cutting tools.

  7. Machining of Some Difficult-to-Cut Materials with Rotary Cutting Tools

    OpenAIRE

    Stjernstoft, Tero

    2004-01-01

    Automobile and aero industries have an increasing interestin materials with improved mechanical properties. However, manyof these new materials are classified as difficult-to-cut withconventional tools. It is obvious that tools, cutting processesand cutting models has to be devel-oped parallel to materialsscience. In this thesis rotary cutting tools are tested as analternative toexpensive diamond or cubic bore nitridetools. Metal matrix composites mostly consist of a light metalalloy (such as...

  8. Cooperative Path-Planning for Multi-Vehicle Systems

    Directory of Open Access Journals (Sweden)

    Qichen Wang

    2014-11-01

    Full Text Available In this paper, we propose a collision avoidance algorithm for multi-vehicle systems, which is a common problem in many areas, including navigation and robotics. In dynamic environments, vehicles may become involved in potential collisions with each other, particularly when the vehicle density is high and the direction of travel is unrestricted. Cooperatively planning vehicle movement can effectively reduce and fairly distribute the detour inconvenience before subsequently returning vehicles to their intended paths. We present a novel method of cooperative path planning for multi-vehicle systems based on reinforcement learning to address this problem as a decision process. A dynamic system is described as a multi-dimensional space formed by vectors as states to represent all participating vehicles’ position and orientation, whilst considering the kinematic constraints of the vehicles. Actions are defined for the system to transit from one state to another. In order to select appropriate actions whilst satisfying the constraints of path smoothness, constant speed and complying with a minimum distance between vehicles, an approximate value function is iteratively developed to indicate the desirability of every state-action pair from the continuous state space and action space. The proposed scheme comprises two phases. The convergence of the value function takes place in the former learning phase, and it is then used as a path planning guideline in the subsequent action phase. This paper summarizes the concept and methodologies used to implement this online cooperative collision avoidance algorithm and presents results and analysis regarding how this cooperative scheme improves upon two baseline schemes where vehicles make movement decisions independently.

  9. Reasoning on the Self-Organizing Incremental Associative Memory for Online Robot Path Planning

    Science.gov (United States)

    Kawewong, Aram; Honda, Yutaro; Tsuboyama, Manabu; Hasegawa, Osamu

    Robot path-planning is one of the important issues in robotic navigation. This paper presents a novel robot path-planning approach based on the associative memory using Self-Organizing Incremental Neural Networks (SOINN). By the proposed method, an environment is first autonomously divided into a set of path-fragments by junctions. Each fragment is represented by a sequence of preliminarily generated common patterns (CPs). In an online manner, a robot regards the current path as the associative path-fragments, each connected by junctions. The reasoning technique is additionally proposed for decision making at each junction to speed up the exploration time. Distinct from other methods, our method does not ignore the important information about the regions between junctions (path-fragments). The resultant number of path-fragments is also less than other method. Evaluation is done via Webots physical 3D-simulated and real robot experiments, where only distance sensors are available. Results show that our method can represent the environment effectively; it enables the robot to solve the goal-oriented navigation problem in only one episode, which is actually less than that necessary for most of the Reinforcement Learning (RL) based methods. The running time is proved finite and scales well with the environment. The resultant number of path-fragments matches well to the environment.

  10. Strategic Team AI Path Plans: Probabilistic Pathfinding

    Directory of Open Access Journals (Sweden)

    Tng C. H. John

    2008-01-01

    Full Text Available This paper proposes a novel method to generate strategic team AI pathfinding plans for computer games and simulations using probabilistic pathfinding. This method is inspired by genetic algorithms (Russell and Norvig, 2002, in that, a fitness function is used to test the quality of the path plans. The method generates high-quality path plans by eliminating the low-quality ones. The path plans are generated by probabilistic pathfinding, and the elimination is done by a fitness test of the path plans. This path plan generation method has the ability to generate variation or different high-quality paths, which is desired for games to increase replay values. This work is an extension of our earlier work on team AI: probabilistic pathfinding (John et al., 2006. We explore ways to combine probabilistic pathfinding and genetic algorithm to create a new method to generate strategic team AI pathfinding plans.

  11. Tool path in torus tool CNC machining

    Directory of Open Access Journals (Sweden)

    XU Ying

    2016-10-01

    Full Text Available This paper is about tool path in torus tool CNC machining.The mathematical model of torus tool is established.The tool path planning algorithm is determined through calculation of the cutter location,boundary discretization,calculation of adjacent tool path and so on,according to the conversion formula,the cutter contact point will be converted to the cutter location point and then these points fit a toolpath.Lastly,the path planning algorithm is implemented by using Matlab programming.The cutter location points for torus tool are calculated by Matlab,and then fit these points to a toolpath.While using UG software,another tool path of free surface is simulated of the same data.It is drew compared the two tool paths that using torus tool is more efficient.

  12. Career Paths in Sport Management

    Science.gov (United States)

    Schwab, Keri A.; Legg, Eric; Tanner, Preston; Timmerman, Danielle; Dustin, Daniel; Arthur-Banning, Skye G.

    2015-01-01

    Sport management alumni (N = 268) from five universities that offer undergraduate programs with an emphasis in sport management within departments of parks, recreation, and tourism were sampled via an electronic survey. The survey sought to learn where alumni were working, and how they felt about their career choice and undergraduate professional…

  13. Antimicrobial packaging for fresh-cut fruits

    Science.gov (United States)

    Fresh-cut fruits are minimally processed produce which are consumed directly at their fresh stage without any further kill step. Microbiological quality and safety are major challenges to fresh-cut fruits. Antimicrobial packaging is one of the innovative food packaging systems that is able to kill o...

  14. 27 CFR 6.92 - Newspaper cuts.

    Science.gov (United States)

    2010-04-01

    ... OF THE TREASURY LIQUORS âTIED-HOUSEâ Exceptions § 6.92 Newspaper cuts. Newspaper cuts, mats, or engraved blocks for use in retailers' advertisements may be given or sold by an industry member to a retailer selling the industry member's products. [T.D. ATF-364, 60 FR 20423, Apr. 26, 1995] ...

  15. Performance Enhancement of Abrasive Waterjet Cutting

    NARCIS (Netherlands)

    2008-01-01

    Abrasive Waterjet (AWJ) Machining is a recent non-traditional machining process. This technology is widely used in industry for cutting difficult-to-machine-materials, milling slots, polishing hard materials etc. AWJ machining has many advantages, e.g. it can cut net-shape parts, no heat is

  16. Gluebond strength of laser cut wood

    Science.gov (United States)

    Charles W. McMillin; Henry A. Huber

    1985-01-01

    The degree of strength loss when gluing laser cut wood as compared to conventionally sawn wood and the amount of additional surface treatment needed to improve bond quality were assessed under normal furniture plant operating conditions. The strength of laser cut oak glued with polyvinyl acetate adhesive was reduced to 75 percent of sawn joints and gum was reduced 43...

  17. Laser cutting - trends in the development,

    DEFF Research Database (Denmark)

    Olsen, Flemming Ove

    2002-01-01

    Since the laser was invented in 1960, the industrial applications of this tool has grown and grown. And - since the beginning of the 1980'ies, the major industrial application of lasers in production has been laser cutting. In this paper a short review of the development of the laser cutting...

  18. Propagation by Cuttings, Layering and Division

    OpenAIRE

    Relf, Diane; Ball, Elizabeth Carter

    2009-01-01

    The major methods of asexual propagation are cuttings, layering, division, and budding/grafting. Cuttings involve rooting a severed piece of the parent plant; layering involves rooting a part of the parent and then severing it; and budding and grafting are joining two plant parts from different varieties.

  19. Meat Cutting Classes--Popular with Adults

    Science.gov (United States)

    Mostad, James; Carpentier, Dale

    1976-01-01

    Presents a session by session description of a "meats" class, which is offered to high school students (9-week period) and adults (8-week period). The classes cover identification of cuts (beef, sheep, hogs, and veal; grades and grading of live animals and carcasses; economics of butchering and cutting your own meat; actual slaughtering; and the…

  20. Postharvest: Cut flowers and potted plants

    Science.gov (United States)

    In the past fifty years, the cut flower market has changed dramatically, from a local market with growers located on city outskirts, to a global one; flowers and cut foliage sourced from throughout the world are sold as bunches or combined into arrangements and bouquets in the major target markets. ...

  1. Cutting the L3 torque tube

    CERN Multimedia

    Laurent Guiraud

    2001-01-01

    Workers cut the torque tube, with a plasma-cutting device on the L3 experiment, which closed with the LEP accelerator in 2000. L3 was housed in a huge red solenoid, which will be taken over by the ALICE detector when the new LHC is completed.

  2. In the suppression of regge cut contributions

    International Nuclear Information System (INIS)

    Chia, S.P.

    1975-07-01

    It is shown that contributions of reggeon-pomeron cuts are suppressed in amplitudes with opposite natural to the reggeon. This suppression grows logarithmically with energy. The suppression in the πP cut is, however, found to be weak. Consequence on conspiracy is discussed

  3. Development of micro pattern cutting simulation software

    International Nuclear Information System (INIS)

    Lee, Jong Min; Song, Seok Gyun; Choi, Jeong Ju; Novandy, Bondhan; Kim, Su Jin; Lee, Dong Yoon; Nam, Sung Ho; Je, Tae Jin

    2008-01-01

    The micro pattern machining on the surface of wide mold is not easy to be simulated by conventional software. In this paper, a software is developed for micro pattern cutting simulation. The 3d geometry of v-groove, rectangular groove, pyramid and pillar patterns are visualized by c++ and OpenGL library. The micro cutting force is also simulated for each pattern

  4. Cutting Watermelon: Lessons in Instructional Coaching

    Science.gov (United States)

    Sandstead, Martha

    2016-01-01

    Literacy coordinator Martha Sandstead finds inspiration for her coaching work in a quote from civil rights organizer Lawrence Guyot: "Let's say you're riding past a picnic, and people are cuttin' watermelons. You don't immediately go and say, "stop the watermelon cutting" and let's talk. … You cut some watermelons, or you help…

  5. Drilling subsurface wellbores with cutting structures

    Science.gov (United States)

    Mansure, Arthur James; Guimerans, Rosalvina Ramona

    2010-11-30

    A system for forming a wellbore includes a drill tubular. A drill bit is coupled to the drill tubular. One or more cutting structures are coupled to the drill tubular above the drill bit. The cutting structures remove at least a portion of formation that extends into the wellbore formed by the drill bit.

  6. AN ADAPTIVE ACO-DRIVEN SCHEME FOR LEARNING AIM ORIENTED PERSONALIZED E-LEARNING

    Directory of Open Access Journals (Sweden)

    Sushma Hans

    2014-10-01

    Full Text Available The e-learning paradigm is now a well-established vehicle of modern education. It caters to a wide spectrum of students with diverse backgrounds who enroll with their own learning aims. A core challenge under this scenario is to generate personalized learning paths so that each student can achieve her learning aim most effectively. Prior works used static attributes such as prior knowledge level, learning ability, browsing preferences, learning style etc. to generate personalized learning paths. In this paper, we take an entirely new route by taking into account the continuous improvement of a learner in the light of her own learning aim, to redefine her learning path at each level of the course. We introduce the concept of personalized examination system that systematically evaluates the dynamic learning ability of every student according to her pre-set goals. The proposed intelligent e-learning system uses Ant Colony Optimization to iteratively optimize the forward learning paths. Experimental results reveal that the system is able to tap a student’s improved learning ability to choose more difficult paths that contribute highly towards her own aims. We demonstrate that the overall learning success of weaker students doubles as compared to statically generated paths while there is considerable improvement of 50% in the learning success for average students as well. This clearly indicates that our approach gives realistic benefits to initially weak students who gradually evolve as the course progresses.

  7. Plasma cutting or laser cutting. Plasma setsudan ka laser setsudan ka

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, A. (Tanaka Engineering Works Ltd., Saitama (Japan))

    1991-05-01

    Comparisons and discussions were made on the plasma cutting and laser cutting in sheet steel cutting, referring partly to gas cutting. Historically, the cutting has been developed from gas, plasma, and laser in that order, and currently these three methods are used mixedly. Generally, the plasma cutting is superior in cutting speed, but inferior in cut face quality, and it requires measures of dust collection. Due to high accuracy and quality in cut face, the laser cutting has been practically used for quite some time in the thin sheet industry, but medium to thick sheet cutting had a problem of unavailability of high output laser suitable for these ranges. However, the recent technologies have overcome the problem as a result of development at the authors {prime} company of a 2 kW class laser cutter capable of cutting 19 mm thick sheet. The cutter has been proven being particularly excellent in controllability. Choice of whether plasma or laser would depend upon which priority is to be taken, cost or accuracy. 15 figs., 3 tabs.

  8. Design of Active N-path Filters

    NARCIS (Netherlands)

    Darvishi, M.; van der Zee, Ronan A.R.; Nauta, Bram

    2013-01-01

    A design methodology for synthesis of active N-path bandpass filters is introduced. Based on this methodology, a 0.1-to-1.2 GHz tunable 6th-order N-path channel-select filter in 65 nm LP CMOS is introduced. It is based on coupling N-path filters with gyrators, achieving a “flat‿ passband shape and

  9. Electric arc, water jet cutting of metals

    International Nuclear Information System (INIS)

    Bruening, D.

    1991-01-01

    For thermal dismantling and cutting of metallic components, as electric arc, water jet cutting method was developed that can be used for underwater cutting work up to a depth of 20 m. Short-circuiting of a continuously fed electrode wire in contact with the metal generates an electric arc which induces partial melting of the metal, and the water jet surrounding the wire rinses away the molten material, thus making a continuous kerf in the material. The method was also tested and modified to allow larger area, surface cutting and removal of metallic surface coatings. This is achieved by melting parts of the surface with the electric arc and subsequent rinsing by the water jet. The cutting and melting depth for surface removal can be accurately controlled by the operating parameters chosen. (orig./DG) [de

  10. High precision tungsten cutting for optics

    International Nuclear Information System (INIS)

    Reglero, V.; Velasco, T.; Rodrigo, J.; Gasent, L.J.; Alamo, J.; Chato, R.; Ruiz Urien, I.; Santos, I.; Zarauz, J.; Clemente, G.; Sanz-Tudanca, C.; Lopez, J.L.

    2001-01-01

    The results obtained during the INTEGRAL masks development program an implementing the HURA and MURA codes on tungsten plates of different thickness are presented. Hard scientific requirements on pixels size and location tolerances (tenths of microns over large areas -1 m 2 - and thickness from 0.5 mm to 60 mm) required the set up of a dedicated program for testing cutting technologies: laser, photochemical milling, spark machining and electro discharge wire cutting. After a very intensive test campaign the wire cutting process was selected as the optimum technology for code manufacturing . Accuracies achieved an the code cutting fulfill scientific requirements. In fact, they are 5 times better than required. Pixel size and centroids location accuracies of 0.01 mm over a 1 m 2 area have been obtained for the 10,000 pixels on IBIS, 100 pixels on SPI and 24000 pixels on JEM-X masks. Comparative results among different cutting technologies are also discussed. (author)

  11. Effects of Cutting Tool Parameters on Vibration

    Directory of Open Access Journals (Sweden)

    Ince Mehmet Alper

    2016-01-01

    Full Text Available This paper presents of the influence on vibration of Co28Cr6Mo medical alloy machined on a CNC lathe based on cutting parameters (rotational speed, feed rate, depth of cut and tool tip radius. The influences of cutting parameters have been presented in graphical form for understanding. To achieve the minimum vibration, the optimum values obtained for rpm, feed rate, depth of cut and tool tip radius were respectively, 318 rpm, 0.25 mm/rev, 0.9 mm and 0.8 mm. Maximum vibration has been revealed the values obtained for rpm, feed rate, depth of cut and tool tip radius were respectively, 636 rpm, 0.1 mm/rev, 0,5 mm and 0.8 mm.

  12. Thermophysical problems of laser cutting of metals

    Directory of Open Access Journals (Sweden)

    Orishich Anatoliy

    2017-01-01

    Full Text Available Variety and complex interaction of physical processes during laser cutting is a critical characteristic of the laser cutting of metals. Small spatial and temporal scales complicate significantly the experimental investigations of the multi-phase fluid flow in the conditions of laser cutting of metals. In these conditions, the surface formed during the cutting is an indicator determining the melt flow character. The quantitative parameter reflecting the peculiarities of the multi-phase fluid flow, is normally the roughness of the forming surface, and the minimal roughness is the criterion of the qualitative flow [1 – 2]. The purpose of this work is to perform the experimental comparative investigation of the thermophysical pattern of the multi-phase melt flow in the conditions of the laser cutting of metals with the laser wavelength of 10.6 μm and 1.07 μm.

  13. Cutting weeds with a CO2 laser

    DEFF Research Database (Denmark)

    Heisel, T.; Schou, Jørgen; Christensen, S.

    2001-01-01

    Stems of Chenopodium album. and Sinapis arvensis. and leaves of Lolium perenne. were cut with a CO2 laser or with a pair of scissors. Treatments were carried out on greenhouse-grown pot plants at three different growth stages and at two heights. Plant dry matter was measured 2 to 5 weeks after...... treatment. The relationship between dry weight and laser energy was analysed using a non-linear dose-response regression model. The regression parameters differed significantly between the weed species. At all growth stages and heights S. arvensis was more difficult to cut with a CO2 laser than C. album....... When stems were cut below the meristems, 0.9 and 2.3 J mm(-1) of CO2 laser energy dose was sufficient to reduce by 90% the biomass of C. album and S. arvensis respectively. Regrowth appeared when dicotyledonous plant stems were cut above meristems, indicating that it is important to cut close...

  14. One-step patterning of hollow microstructures in paper by laser cutting to create microfluidic analytical devices.

    Science.gov (United States)

    Nie, Jinfang; Liang, Yuanzhi; Zhang, Yun; Le, Shangwang; Li, Dunnan; Zhang, Songbai

    2013-01-21

    In this paper, we report a simple, low-cost method for rapid, highly reproductive fabrication of paper-based microfluidics by using a commercially available, minitype CO(2) laser cutting/engraving machine. This method involves only one operation of cutting a piece of paper by laser according to a predesigned pattern. The hollow microstructures formed in the paper are used as the 'hydrophobic barriers' to define the hydrophilic flowing paths. A typical paper device on a 4 cm × 4 cm piece of paper can be fabricated within ∼7-20 s; it is ready for use once the cutting process is finished. The main fabrication parameters such as the applied current and cutting rate of the laser were optimized. The fabrication resolution and multiplexed analytical capability of the hollow microstructure-patterned paper were also characterized.

  15. Path integrals and geometry of trajectories

    International Nuclear Information System (INIS)

    Blau, M.; Keski-Vakkuri, E.; Niemi, A.J.

    1990-01-01

    A geometrical interpretation of path integrals is developed in the space of trajectories. This yields a supersymmetric formulation of a generic path integral, with the supersymmetry resembling the BRST supersymmetry of a first class constrained system. If the classical equation of motion is a Killing vector field in the space of trajectories, the supersymmetry localizes the path integral to classical trajectories and the WKB approximation becomes exact. This can be viewed as a path integral generalization of the Duistermaat-Heckman theorem, which states the conditions for the exactness of the WKB approximation for integrals in a compact phase space. (orig.)

  16. Path integrals for arbitrary canonical transformations

    International Nuclear Information System (INIS)

    Oliveira, L.A.R. de.

    1980-01-01

    Some aspects of the path integral formulation of quantum mechanics are studied. This formalism is generalized to arbitrary canonical transformations, by means of an association between path integral probalility amplitudes and classical generators of transformations, analogous to the usual Hamiltonian time development phase space expression. Such association turns out to be equivalent to the Weyl quantization rule, and it is also shown that this formalism furnishes a path integral representation for a Lie algebra of a given set of classical generators. Some physical considerations about the path integral quantization procedure and about the relationship between classical and quantum dynamical structures are also discussed. (Author) [pt

  17. Techniques and applications of path integration

    CERN Document Server

    Schulman, L S

    2005-01-01

    A book of techniques and applications, this text defines the path integral and illustrates its uses by example. It is suitable for advanced undergraduates and graduate students in physics; its sole prerequisite is a first course in quantum mechanics. For applications requiring specialized knowledge, the author supplies background material.The first part of the book develops the techniques of path integration. Topics include probability amplitudes for paths and the correspondence limit for the path integral; vector potentials; the Ito integral and gauge transformations; free particle and quadra

  18. Symbolic PathFinder v7

    DEFF Research Database (Denmark)

    Luckow, Kasper Søe; Păsăreanu, Corina

    2014-01-01

    We describe Symbolic PathFinder v7 in terms of its updated design addressing the changes of Java PathFinder v7 and of its new optimization when computing path conditions. Furthermore, we describe the Symbolic Execution Tree Extension; a newly added feature that allows for outputting the symbolic...... execution tree that characterizes the execution paths covered during symbolic execution. The new extension can be tailored to the needs of subsequent analyses/processing facilities, and we demonstrate this by presenting SPF-Visualizer, which is a tool for customizable visualization of the symbolic execution...

  19. Joint modeling of constrained path enumeration and path choice behavior: a semi-compensatory approach

    DEFF Research Database (Denmark)

    Kaplan, Sigal; Prato, Carlo Giacomo

    2010-01-01

    A behavioural and a modelling framework are proposed for representing route choice from a path set that satisfies travellers’ spatiotemporal constraints. Within the proposed framework, travellers’ master sets are constructed by path generation, consideration sets are delimited according to spatio...

  20. Laser cutting or water-jet cutting. Laser setsudan ka water-jet setsudan ka

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, T. (Shibuya Kogyo Co. Ltd., Ishikawa (Japan))

    1991-05-01

    The recent spread of carbon oxide laser cutter is so startlingly fast, but at the same time, water jet cutting using ultra high pressure water stream is drawing attention as it has identical characteristics, and opens the way to cutting materials that have been hitherto difficult to cut. The authors, who are fabricators of cutters of both types, gave the comparisons and explanations on several examples referring to materials that can be cut, cutting accuracy, speed, shape and thermal effects to cut face, and running cost in detail. However, simple comparison is difficult. For instance, cutting 6 mm thick SUS sheet costs a running cost of 65 yen per meter in laser cutting, and 535 yen per meter in water jet cutting, but this situation is often reversed when other material or sheet thickness is selected. The actual situation in the sheet metal processing industry at the present time is that it uses by far more laser processing machines, and uses water jet cutters to supplement for cutting materials more difficult to cut. 10 figs., 3 tabs.

  1. Laser circular cutting of Kevlar sheets: Analysis of thermal stress filed and assessment of cutting geometry

    Science.gov (United States)

    Yilbas, B. S.; Akhtar, S. S.; Karatas, C.

    2017-11-01

    A Kevlar laminate has negative thermal expansion coefficient, which makes it difficult to machine at room temperaures using the conventional cutting tools. Contararily, laser machining of a Kevlar laminate provides advantages over the conventional methods because of the non-mechanical contact between the cutting tool and the workpiece. In the present study, laser circular cutting of Kevlar laminate is considered. The experiment is carried out to examine and evaluate the cutting sections. Temperature and stress fields formed in the cutting section are simulated in line with the experimental study. The influence of hole diameters on temperature and stress fields are investigated incorporating two different hole diameters. It is found that the Kevlar laminate cutting section is free from large size asperities such as large scale sideways burnings and attachemnt of charred residues. The maximum temperature along the cutting circumference remains higher for the large diameter hole than that of the small diameter hole. Temperature decay is sharp around the cutting section in the region where the cutting terminates. This, in turn, results in high temperature gradients and the thermal strain in the cutting region. von Mises stress remains high in the region where temperature gradients are high. von Mises stress follows similar to the trend of temperature decay around the cutting edges.

  2. Experimental improvement of the technology of cutting of high-pressure hoses with metal braid on hand cutting machine

    OpenAIRE

    Karpenko, Mykola; Bogdevicius, Marijonas; Prentkovskis, Olegas

    2016-01-01

    In the article the review of the problem of improvement of technology of high pressure hoses cutting on the hand cutting machines is analyzed. Different methods of cutting of high pressure hoses into the billets are overviewed and the quality of edge cuts of hoses is analyzed. The comparison of treatment on automatic cutting machines and on hand cutting machines is carried out. Different experimental techniques of improvement of the quality of edges cutting of high pressure hoses are prese...

  3. Practicality of diversion path analysis

    International Nuclear Information System (INIS)

    Murphey, W.M.; Schleter, J.C.

    1974-07-01

    One can define the safeguards system for nuclear material as the set of all protective actions taken to prevent or to deter attempts to divert nuclear material to unauthorized use. Maintenance of effective safeguards requires a program for routine assessment of plant safeguards systems in terms of their capabilities to satisfy safeguards aims. Plant internal control systems provide capabilities for detection of unprevented diversion and can provide assurance that diversion has not occurred. A procedure called Diversion Path Analysis (DPA) enables routine assessment of the capabilities of internal control systems in this regard and identification of safeguards problem areas in a plant. A framework for safeguards system design is also provided which will allow flexibility to accommodate individual plant circumstances while maintaining acceptable diversion detection capability. The steps of the procedure are described and the practicality of the analytical method is shown by referring to a demonstration test for a high throughput process where plant personnel were major participants. The boundary conditions for the demonstration case are given, along with some conclusions about the general procedure. (U.S.)

  4. Inked Careers: Tattooing Professional Paths

    Directory of Open Access Journals (Sweden)

    Gabriela DeLuca

    2016-12-01

    Full Text Available The concept of career has an interdisciplinary and historical constitution, which includes persons, groups, organizations and society. Given that, we aim to deepen the interactionist notion of career from the understanding of a deviant path, supported by a theory and a method appropriated to the cited call for interdisciplinary approaches. Dilemmas (Hughes, 1958 and conflicts (Hughes, 1937 emerged as important analytical categories. Although necessary, these two concepts were not sufficient to contemplate analyses in their entirety. For this reason we conceptualized a third possibility of controversy during a career: the inquiries. The study followed the Narrative method to analyze objective and subjective changes during a tattoo artist’s career through interviews and informal conversations carried out over 22 months. The discussion presents three main contributions. Theoretically, a new understanding of the concept of careers, linking past, present and future and the idea of non-linearity of experienced and envisioned careers. Methodologically, suggesting orientations for future career studies such as the use of turning points as a methodological tool and the investigation of deviant fields. Finally, our defense of the interactionist perspective as suitable for career studies, since it allows the investigation of deviant elements.

  5. Medical writing on an accelerated path in India

    Science.gov (United States)

    Shirke, Sarika

    2015-01-01

    The medical writing industry is on an upwards growth path in India. This is probably driven by an increasing urgency to have high-quality documents authored to support timely drug approvals, complemented by the realization that the competencies required are available in emerging geographies such as India. This article reviews the business landscape and the opportunities and challenges associated with outsourcing medical writing work India. It also analyzes the core competencies that a medical writer should possess and enlists various associations supporting learning in this domain. PMID:26229746

  6. Medical writing on an accelerated path in India.

    Science.gov (United States)

    Shirke, Sarika

    2015-01-01

    The medical writing industry is on an upwards growth path in India. This is probably driven by an increasing urgency to have high-quality documents authored to support timely drug approvals, complemented by the realization that the competencies required are available in emerging geographies such as India. This article reviews the business landscape and the opportunities and challenges associated with outsourcing medical writing work India. It also analyzes the core competencies that a medical writer should possess and enlists various associations supporting learning in this domain.

  7. Restraining and neck cutting or stunning and neck cutting of veal calves.

    Science.gov (United States)

    Lambooij, E; van der Werf, J T N; Reimert, H G M; Hindle, V A

    2012-05-01

    Brain and heart activities were measured in 31 veal calves during restraining and rotating followed by neck cutting with or without stunning to evaluate welfare. After neck cutting correlation dimension analyses and %power of EEG beta wave fraction decreased gradually to lower values resulting in an induction of unconsciousness lasting on average 80s. Corneal reflex response ceased 135±57s after neck cutting. The CD scores and the %power of beta waves fell immediately after post-cut captive bolt and pre-cut electrical stunning to levels indicating unconsciousness. Heart rate in lairage increased upon entrance to the restrainer and again after rotation, heart rate variability decreased. Rotating the restrainer 90°, 120° or 180° compromised veal calf welfare and should be avoided. It is recommended to use post-cut captive bolt stunning or pre-cut electrical stunning inducing immediate unconsciousness. Copyright © 2011 Elsevier Ltd. All rights reserved.

  8. International feedback experience on the cutting of reactor internal components

    International Nuclear Information System (INIS)

    Boucau, J.

    2014-01-01

    Westinghouse capitalizes more than 30 years of experience in the cutting of internal components of reactor and their packaging in view of their storage. Westinghouse has developed and validated different methods for cutting: plasma torch cutting, high pressure abrasive water jet cutting, electric discharge cutting and mechanical cutting. A long feedback experience has enabled Westinghouse to list the pros and cons of each cutting technology. The plasma torch cutting is fast but rises dosimetry concerns linked to the control of the cuttings and the clarity of water. Abrasive water jet cutting requires the installation of costly safety devices and of an equipment for filtering water but this technology allows accurate cuttings in hard-to-reach zones. Mechanical cutting is the most favourable technology in terms of wastes generation and of the clarity of water but the cutting speed is low. (A.C.)

  9. Development of cutting device for irradiated fuel rod

    International Nuclear Information System (INIS)

    Lee, E. P.; Jun, Y. B.; Hong, K. P.; Min, D. K.; Lee, H. K.; Su, H. S.; Kim, K. S.; Kwon, H. M.; Joo, Y. S.; Yoo, K. S.; Joo, J. S.; Kim, E. K.

    2004-01-01

    Post Irradiation Examination(PIE) on irradiated fuel rods is essential for the evaluation of integrity and irradiation performance of fuel rods of commercial reactor fuel. For PIE, fuel rods should be cut very precisely. The cutting positions selected from NDT data are very important for further destructive examination and analysis. A fuel rod cutting device was developed witch can cut fuel rods longitudinal very precisely and can also cut the fuels into the same length rod cuts repeatedly. It is also easy to remove the fuel cutting powder after cutting works and it can extend the life time of cutting device and lower the contamination level of hot cell

  10. Two Generations of Path Dependence in Economics?

    DEFF Research Database (Denmark)

    Madsen, Mogens Ove

    2010-01-01

    Even if there is no fully articulated and generally accepted theory of Path Dependence it has eagerly been taken up across a wide range of social sciences – primarily coming from economics. Path Dependence is most of all a metaphor that offers reason to believe, that some political, social...

  11. Cooperative organic mine avoidance path planning

    Science.gov (United States)

    McCubbin, Christopher B.; Piatko, Christine D.; Peterson, Adam V.; Donnald, Creighton R.; Cohen, David

    2005-06-01

    The JHU/APL Path Planning team has developed path planning techniques to look for paths that balance the utility and risk associated with different routes through a minefield. Extending on previous years' efforts, we investigated real-world Naval mine avoidance requirements and developed a tactical decision aid (TDA) that satisfies those requirements. APL has developed new mine path planning techniques using graph based and genetic algorithms which quickly produce near-minimum risk paths for complicated fitness functions incorporating risk, path length, ship kinematics, and naval doctrine. The TDA user interface, a Java Swing application that obtains data via Corba interfaces to path planning databases, allows the operator to explore a fusion of historic and in situ mine field data, control the path planner, and display the planning results. To provide a context for the minefield data, the user interface also renders data from the Digital Nautical Chart database, a database created by the National Geospatial-Intelligence Agency containing charts of the world's ports and coastal regions. This TDA has been developed in conjunction with the COMID (Cooperative Organic Mine Defense) system. This paper presents a description of the algorithms, architecture, and application produced.

  12. Evaluation of Calcine Disposition Path Forward

    International Nuclear Information System (INIS)

    Birrer, S.A.; Heiser, M.B.

    2003-01-01

    This document describes an evaluation of the baseline and two alternative disposition paths for the final disposition of the calcine wastes stored at the Idaho Nuclear Technology and Engineering Center at the Idaho National Engineering and Environmental Laboratory. The pathways are evaluated against a prescribed set of criteria and a recommendation is made for the path forward

  13. Generalized measures and the Feynman path integral

    International Nuclear Information System (INIS)

    Maslov, V.P.; Chebotarev, A.M.

    1976-01-01

    Generalizations are obtained for the earlier results by the authors concerning the inclusion of the Feynmann path integral in the momentum representation into the general integration theory. Feynmann path integrals are considered which do not represent T-products. Generalized Feynmann measure in the configuration representation is introduced

  14. Approximate Shortest Homotopic Paths in Weighted Regions

    KAUST Repository

    Cheng, Siu-Wing; Jin, Jiongxin; Vigneron, Antoine; Wang, Yajun

    2010-01-01

    Let P be a path between two points s and t in a polygonal subdivision T with obstacles and weighted regions. Given a relative error tolerance ε ∈(0,1), we present the first algorithm to compute a path between s and t that can be deformed to P

  15. Paths and cycles in colored graphs

    NARCIS (Netherlands)

    Li, Xueliang; Zhang, Shenggui; Hurink, Johann L.; Pickl, Stefan; Broersma, Haitze J.; Faigle, U.

    2001-01-01

    Let G be an (edge-)colored graph. A path (cycle) is called monochromatic if all the edges of it have the same color, and is called heterochromatic if all the edges of it have different colors. In this note, some sufficient conditions for the existence of monochromatic and heterochromatic paths and

  16. Path Minima Queries in Dynamic Weighted Trees

    DEFF Research Database (Denmark)

    Davoodi, Pooya; Brodal, Gerth Stølting; Satti, Srinivasa Rao

    2011-01-01

    In the path minima problem on a tree, each edge is assigned a weight and a query asks for the edge with minimum weight on a path between two nodes. For the dynamic version of the problem, where the edge weights can be updated, we give data structures that achieve optimal query time\\todo{what about...

  17. Approximate shortest homotopic paths in weighted regions

    KAUST Repository

    Cheng, Siuwing; Jin, Jiongxin; Vigneron, Antoine E.; Wang, Yajun

    2012-01-01

    A path P between two points s and t in a polygonal subdivision T with obstacles and weighted regions defines a class of paths that can be deformed to P without passing over any obstacle. We present the first algorithm that, given P and a relative

  18. from synchronic variation to a grammaticalization path

    African Journals Online (AJOL)

    Kate H

    Abstract. The authors argue that the synchronic variation of cognate objects of weather verbs exhibited in six African languages of South Africa (Sepedi, Sesotho, Tshivenda, isiXhosa, Xitsonga, and. isiZulu) has a diachronic explanation, and may be represented as a grammaticalization path. This path gradually leads from ...

  19. Deferment cutting in Appalachian hardwoods: the what, whys, and hows

    Science.gov (United States)

    H. Clay Smith; Gary W. Miller

    1991-01-01

    Deferment cutting is a regeneration practice that resembles a seed-tree or shelterwood cutting. The difference is that residual trees are not cut when the reproduction becomes established. Instead, residual trees are left until new reproduction matures to sawtimber size, and another regeneration cut is the silvicultural objective. Hence, with deferment cutting specific...

  20. Cut elimination in multifocused linear logic

    DEFF Research Database (Denmark)

    Guenot, Nicolas; Brock-Nannestad, Taus

    2015-01-01

    We study cut elimination for a multifocused variant of full linear logic in the sequent calculus. The multifocused normal form of proofs yields problems that do not appear in a standard focused system, related to the constraints in grouping rule instances in focusing phases. We show that cut...... elimination can be performed in a sensible way even though the proof requires some specific lemmas to deal with multifocusing phases, and discuss the difficulties arising with cut elimination when considering normal forms of proofs in linear logic....

  1. Automatic turbot fish cutting using machine vision

    OpenAIRE

    Martín Rodríguez, Fernando; Barral Martínez, Mónica

    2015-01-01

    This paper is about the design of an automated machine to cut turbot fish specimens. Machine vision is a key part of this project as it is used to compute a cutting curve for specimen’s head. This task is impossible to be carried out by mechanical means. Machine vision is used to detect head boundary and a robot is used to cut the head. Afterwards mechanical systems are used to slice fish to get an easy presentation for end consumer (as fish fillets than can be easily marketed ...

  2. Reconfigurable manufacturing execution system for pipe cutting

    Science.gov (United States)

    Yin, Y. H.; Xie, J. Y.

    2011-08-01

    This article presents a reconfigurable manufacturing execution system (RMES) filling the gap between enterprise resource planning and resource layer for pipe-cutting production with mass customisation and rapid adaptation to dynamic market, which consists of planning and scheduling layer and executive control layer. Starting from customer's task and process requirements, the cutting trajectories are planned under generalised mathematical model able to reconfigure in accordance with various intersecting types' joint, and all tasks are scheduled by nesting algorithm to maximise the utilisation rate of rough material. This RMES for pipe cutting has been effectively implemented in more than 100 companies.

  3. Cut Locus Construction using Deformable Simplicial Complexes

    DEFF Research Database (Denmark)

    Misztal, Marek Krzysztof; Bærentzen, Jakob Andreas; Anton, François

    2011-01-01

    In this paper we present a method for appproximating cut loci for a given point p on Riemannian 2D manifolds, closely related to the notion of Voronoi diagrams. Our method finds the cut locus by advecting a front of points equally distant from p along the geodesics originating at p and finding...... the domain to have disk topology. We test our method for tori of revolution and compare our results to the benchmark ones from [2]. The method, however, is generic and can be easily adapted to construct cut loci for other manifolds of genera other than 1....

  4. Designing for hot-blade cutting

    DEFF Research Database (Denmark)

    Brander, David; Bærentzen, Jakob Andreas; Clausen, Kenn

    2016-01-01

    In this paper we present a novel method for the generation of doubly-curved, architectural design surfaces using swept Euler elastica and cubic splines. The method enables a direct design to production workflow with robotic hot-blade cutting, a novel robotic fabrication method under development......-trivial constraints of blade-cutting in a bottom-up fashion, enabling an exploration of the unique architectural potential of this fabrication approach. The method is implemented as prototype design tools in MatLAB, C++, GhPython, and Python and demonstrated through cutting of expanded polystyrene foam design...

  5. Optimization of educational paths for higher education

    Science.gov (United States)

    Tarasyev, Alexandr A.; Agarkov, Gavriil; Medvedev, Aleksandr

    2017-11-01

    In our research, we combine the theory of economic behavior and the methodology of increasing efficiency of the human capital to estimate the optimal educational paths. We provide an optimization model for higher education process to analyze possible educational paths for each rational individual. The preferences of each rational individual are compared to the best economically possible educational path. The main factor of the individual choice, which is formed by the formation of optimal educational path, deals with higher salaries level in the chosen economic sector after graduation. Another factor that influences on the economic profit is the reduction of educational costs or the possibility of the budget support for the student. The main outcome of this research consists in correction of the governmental policy of investment in human capital based on the results of educational paths optimal control.

  6. Consider outsourcing IT projects when cutting-edge technology, specialized focus are needed.

    Science.gov (United States)

    1999-05-01

    Looking outside to meet information technology needs proves a smart way to avert extra staffing costs. Kaiser Permanente saves thousands each year by contracting out cutting-edge IT projects instead of hiring more full-time staff it doesn't need. Learn how the organization incorporates outsourcing and other temporary work methods into its IT staffing strategy.

  7. Survival paths through the forest

    DEFF Research Database (Denmark)

    Mogensen, Ulla Brasch

    in appropriate prevention programs it is important to assess the individual risk with high accuracy. Generally, genetic information plays an important role for many diseases and will help to improve the accuracy of existing risk prediction models. However, conventional regression models have several limitations...... when the information is high-dimensional e.g. when there are many thousands of genes or markers. In these situations machine learning methods such as the random forest can still be applied and provide reasonable prediction accuracy. The main focus in this talk is the performance of random forest...

  8. A network analysis of blended learning: Perceived causal relations between use of learning resources, regulation strategies and course performance

    NARCIS (Netherlands)

    Bos, Nynke; Meijer, Bren; Brand-Gruwel, Saskia

    2018-01-01

    Blended learning is often associated with student-oriented learning in which students have more control over the learning path, which will stimulate self-regulated and deeper learning. Although the perceived value of blended learning is clear, less is known if and how blended learning contributes to

  9. Cutting method for structural component into block like shape, and device used for cutting

    International Nuclear Information System (INIS)

    Nakazawa, Koichi; Ito, Akira; Tateiwa, Masaaki.

    1995-01-01

    Two grooves each of a predetermined depth are formed along a surface of a structural component, and a portion between the two grooves is cut in the direction of the depth from the surface of the structural component by using a cutting wire of a wire saw device. Then, the cutting wire is moved in the extending direction of the grooves while optionally changing the position in the direction of the depth to conduct cutting for the back face. Further, the cutting wire is moved in the direction of the depth of the groove toward the surface, to cut a portion between the two grooves. The wire saw device comprises a wire saw main body movable along the surface of the structural component, a pair of wire guide portions extending in the direction of the depth, guide pooleys capable of guiding the cutting wire guides revolvably and rotatably disposed at the top end, and an endless annular cutting wire extending between the wire guide portions. Thus, it is possible to continuously cut out blocks set to optional size and thickness. In addition, remote cutting is possible with no requirement for an operator to access to the vicinity of radioactivated portions. (N.H.)

  10. An FMS Dynamic Production Scheduling Algorithm Considering Cutting Tool Failure and Cutting Tool Life

    International Nuclear Information System (INIS)

    Setiawan, A; Wangsaputra, R; Halim, A H; Martawirya, Y Y

    2016-01-01

    This paper deals with Flexible Manufacturing System (FMS) production rescheduling due to unavailability of cutting tools caused either of cutting tool failure or life time limit. The FMS consists of parallel identical machines integrated with an automatic material handling system and it runs fully automatically. Each machine has a same cutting tool configuration that consists of different geometrical cutting tool types on each tool magazine. The job usually takes two stages. Each stage has sequential operations allocated to machines considering the cutting tool life. In the real situation, the cutting tool can fail before the cutting tool life is reached. The objective in this paper is to develop a dynamic scheduling algorithm when a cutting tool is broken during unmanned and a rescheduling needed. The algorithm consists of four steps. The first step is generating initial schedule, the second step is determination the cutting tool failure time, the third step is determination of system status at cutting tool failure time and the fourth step is the rescheduling for unfinished jobs. The approaches to solve the problem are complete-reactive scheduling and robust-proactive scheduling. The new schedules result differences starting time and completion time of each operations from the initial schedule. (paper)

  11. Comparative Investigation on Tool Wear during End Milling of AISI H13 Steel with Different Tool Path Strategies

    Science.gov (United States)

    Adesta, Erry Yulian T.; Riza, Muhammad; Avicena

    2018-03-01

    Tool wear prediction plays a significant role in machining industry for proper planning and control machining parameters and optimization of cutting conditions. This paper aims to investigate the effect of tool path strategies that are contour-in and zigzag tool path strategies applied on tool wear during pocket milling process. The experiments were carried out on CNC vertical machining centre by involving PVD coated carbide inserts. Cutting speed, feed rate and depth of cut were set to vary. In an experiment with three factors at three levels, Response Surface Method (RSM) design of experiment with a standard called Central Composite Design (CCD) was employed. Results obtained indicate that tool wear increases significantly at higher range of feed per tooth compared to cutting speed and depth of cut. This result of this experimental work is then proven statistically by developing empirical model. The prediction model for the response variable of tool wear for contour-in strategy developed in this research shows a good agreement with experimental work.

  12. Magnetofluidic testing of rock cutting knives

    International Nuclear Information System (INIS)

    Buioca, C.D.; Iusan, Vasile; Pirlea, Remus

    2002-01-01

    The nondestructive testing of cutting knives consists in the determination of nonuniformity of a magnetic fluid layer applied on the horizontally placed surface of the magnetized cutting plate of the knife. A low constant magnetic field was applied perpendicular to the knife surface and a uniform magnetic fluid layer was applied. The defects as nonuniform brass layer, fissures or small cavities between the cutting plate and knife core determine the apparition of magnetic field gradients and therefore magnetic forces acting on the magnetic fluid which migrates to the zones with higher magnetic field intensity. After several minutes, a nonuniform layer of magnetic fluid was directly observed. Quantitative results, concerning the position and dimensions of the defect, were obtained by computer aided processing of the magnetic fluid layer image. Experimental data for several cutting knives are presented in the paper

  13. Automated Cell-Cutting for Cell Cloning

    Science.gov (United States)

    Ichikawa, Akihiko; Tanikawa, Tamio; Matsukawa, Kazutsugu; Takahashi, Seiya; Ohba, Kohtaro

    We develop an automated cell-cutting technique for cell cloning. Animal cells softened by the cytochalasin treatment are injected into a microfluidic chip. The microfluidic chip contains two orthogonal channels: one microchannel is wide, used to transport cells, and generates the cutting flow; the other is thin and used for aspiration, fixing, and stretching of the cell. The injected cell is aspirated and stretched in the thin microchannel. Simultaneously, the volumes of the cell before and after aspiration are calculated; the volumes are used to calculate the fluid flow required to aspirate half the volume of the cell into the thin microchannel. Finally, we apply a high-speed flow in the orthogonal microchannel to bisect the cell. This paper reports the cutting process, the cutting system, and the results of the experiment.

  14. Spending and cutting are two different worlds

    DEFF Research Database (Denmark)

    Houlberg, Kurt; Olsen, Asmus Leth; Pedersen, Lene Holm

    2016-01-01

    This article investigates politicians’ preferences for cutting and spending. The research questions are where do politicians prefer to cut, where do they prefer to spend and how is this influenced by political ideology? These questions are investigated in a large-scale survey experiment fielded...... to Danish local councillors, who are randomly assigned to a decision-making situation, where the block grant provided to their municipality is either increased or reduced. The results show that the politicians’ preferences for cutting and spending are asymmetric, in the sense that the policy areas, which...... are assigned the least cuts when the grant is reduced, are rarely the ones which are assigned extra money when the grant is increased. Areas with well-organised interests and a target group which is perceived as deserving are granted more money, whereas policy areas where the target group is perceived as less...

  15. Diamond wire cutting of heat exchangers

    International Nuclear Information System (INIS)

    Beckman, T.R.; Bjerler, J.

    1991-01-01

    With the change-out of equipment at nuclear power plants comes large quantities of low level contaminated metallic waste. Of particular concern are large heat exchangers, preheaters and steam generators. These bulky items consume huge volumes of burial space. The need for volume reduction and recycling of these metals has created new demands for 'how' to cut heat exchangers into useful sizes for decontamination, melting or compaction. This paper reviews the cutting solution provided by a diamond wire system, with particular regard for cutting of a Ringhals Preheater Bundle at Studsvik Nuclear in 1989. The background of diamond wire sawing is discussed and basic components of wire sawing are explained. Other examples of wire cutting decommissioned components are also given. (author)

  16. Assembly procedure for column cutting platform

    International Nuclear Information System (INIS)

    Routh, R.D.

    1995-01-01

    This supporting document describes the assembly procedure for the Column Cutting Platform and Elevation Support. The Column Cutting Platform is a component of the 241-SY-101 Equipment Removal System. It is set up on the deck of the Strongback Trailer to provide work access to cut off the upper portion of the Mitigation Pump Assembly (MPA). The Elevation Support provides support for the front of the Storage Container with the Strongback at an inclined position. The upper portion of the MPA must be cut off to install the Containment Caps on the Storage Container. The storage Container must be maintained in an inclined position until the Containment Caps are installed to prevent any residual liquids from migrating forward in the Storage Container

  17. Alternative Constraint Handling Technique for Four-Bar Linkage Path Generation

    Science.gov (United States)

    Sleesongsom, S.; Bureerat, S.

    2018-03-01

    This paper proposes an extension of a new concept for path generation from our previous work by adding a new constraint handling technique. The propose technique was initially designed for problems without prescribed timing by avoiding the timing constraint, while remain constraints are solving with a new constraint handling technique. The technique is one kind of penalty technique. The comparative study is optimisation of path generation problems are solved using self-adaptive population size teaching-learning based optimization (SAP-TLBO) and original TLBO. In this study, two traditional path generation test problem are used to test the proposed technique. The results show that the new technique can be applied with the path generation problem without prescribed timing and gives better results than the previous technique. Furthermore, SAP-TLBO outperforms the original one.

  18. Optimal path-finding through mental exploration based on neural energy field gradients.

    Science.gov (United States)

    Wang, Yihong; Wang, Rubin; Zhu, Yating

    2017-02-01

    Rodent animal can accomplish self-locating and path-finding task by forming a cognitive map in the hippocampus representing the environment. In the classical model of the cognitive map, the system (artificial animal) needs large amounts of physical exploration to study spatial environment to solve path-finding problems, which costs too much time and energy. Although Hopfield's mental exploration model makes up for the deficiency mentioned above, the path is still not efficient enough. Moreover, his model mainly focused on the artificial neural network, and clear physiological meanings has not been addressed. In this work, based on the concept of mental exploration, neural energy coding theory has been applied to the novel calculation model to solve the path-finding problem. Energy field is constructed on the basis of the firing power of place cell clusters, and the energy field gradient can be used in mental exploration to solve path-finding problems. The study shows that the new mental exploration model can efficiently find the optimal path, and present the learning process with biophysical meaning as well. We also analyzed the parameters of the model which affect the path efficiency. This new idea verifies the importance of place cell and synapse in spatial memory and proves that energy coding is effective to study cognitive activities. This may provide the theoretical basis for the neural dynamics mechanism of spatial memory.

  19. Study and Research Paths at Upper Secondary Mathematics Education

    DEFF Research Database (Denmark)

    Jessen, Britta Eyrich

    the scope of teaching at this level. With respect to mathematical modelling, links and gaps were identified between scholarly knowledge and knowledge to be taught in secondary school. It is suggested that SRP based teaching can bridge parts of the identified gaps. Finally, it is found that in order for SRP......In didactics of mathematics, researchers have for decades been interested in how to teach students to pose questions and solve problems. Several approaches rely on the idea, that students learn mathematics, when they are engaged in activities similar to research mathematicians. This PhD project...... touch upon these ideas from the perspective offered by the Anthropological Theory of Didactics (ATD ). Within ATD, teaching is proposed to be designed as Study and Research Paths (SRP). This thesis investigates how SRP's support the students' learning of mathematics in a bidisciplinary context involving...

  20. Fuel Handling Equipment Maintenance for Critical Path Time Savings

    Energy Technology Data Exchange (ETDEWEB)

    Saville, M.; Williams, A.

    2015-07-01

    By sharing lessons learned and operating experience gained by AREVA Stearns RogerTM Services from more than 45 years of servicing, maintaining, and upgrading Fuel Handling Equipment (FHE) and as the original equipment manufacturer to 56% of domestic U.S. FHE (PWR and BWR) as well as 19 units overseas, this paper presents trends and market forces that have led to the neglect of FHE, the risks of not adequately maintaining FHE, and the financial benefits of proactively maintaining FHE. The benefit to audiences is to come to a better understanding of how critical path delays can be avoided and thus reduce nuclear power plant operating costs. Note that statistics and monetary values given herein are based on recent typical experiences of AREVA Stearns RogerTM Services. Examples discussed are based on actual lessons learned. For the purposes of this paper, upgrades are considered a part of equipment maintenance unless specifically discussed separately. (Author)