Stoichiometric and lean burn heavy-duty gas engines: a dilemma between emissions and fuel consumption?

NARCIS (Netherlands)

Steen, M. van der; Rijke, J. de; Seppen, J.J.

1996-01-01

This paper compares stoichiometric with lean burn technology for heavy-duty gas engines (natural gas and LPG) and demonstrates that there is a future for both engine concepts on the multilateral global market. Emission limits in Europe as expected in the near future will facilitate both engine

Effect of hydrogen addition on burning rate and surface density of turbulent lean premixed methane-air flames

International Nuclear Information System (INIS)

Guo, H.; Tayebi, B.; Galizzi, C.; Escudie, D.

2009-01-01

Hydrogen (H 2 ) is a clean burning component, but relatively expensive. Mixing a small amount of hydrogen with other fuels is an effective way to use H 2 . H 2 enriched combustion significantly improves fuel efficiency and reduces pollutant (nitrogen oxide and particulate matter) emissions. This presentation discussed the effect of hydrogen addition on burning rate and surface density of turbulent lean premixed methane-air flames. The presentation discussed flame configuration; the experimental methodology using laser tomography; and results for typical images, burning velocity, ratio of turbulent to laminar burning velocities, flame surface density, curvature, flame brush thickness, and integrated flame surface area. It was concluded that the increase of turbulent burning velocity was faster than that of laminar burning velocity, which contradicted traditional theory. figs.

Sector Tests of a Low-NO(sub x), Lean, Direct- Injection, Multipoint Integrated Module Combustor Concept Conducted

Science.gov (United States)

Tacina, Robert R.; Wey, Chang-Lie; Laing, Peter; Mansour, Adel

2002-01-01

The low-emissions combustor development described is directed toward advanced high pressure aircraft gas-turbine applications. The emphasis of this research is to reduce nitrogen oxides (NOx) at high-power conditions and to maintain carbon monoxide and unburned hydrocarbons at their current low levels at low power conditions. Low-NOx combustors can be classified into rich-burn and lean-burn concepts. Lean-burn combustors can be further classified into lean-premixed-prevaporized (LPP) and lean direct injection (LDI) concepts. In both concepts, all the combustor air, except for liner cooling flow, enters through the combustor dome so that the combustion occurs at the lowest possible flame temperature. The LPP concept has been shown to have the lowest NOx emissions, but for advanced high-pressure-ratio engines, the possibility of autoignition or flashback precludes its use. LDI differs from LPP in that the fuel is injected directly into the flame zone, and thus, it does not have the potential for autoignition or flashback and should have greater stability. However, since it is not premixed and prevaporized, good atomization is necessary and the fuel must be mixed quickly and uniformly so that flame temperatures are low and NOx formation levels are comparable to those of LPP. The LDI concept described is a multipoint fuel injection/multiburning zone concept. Each of the multiple fuel injectors has an air swirler associated with it to provide quick mixing and a small recirculation zone for burning. The multipoint fuel injection provides quick, uniform mixing and the small multiburning zones provide for reduced burning residence time, resulting in low NOx formation. An integrated-module approach was used for the construction where chemically etched laminates, diffusion bonded together, combine the fuel injectors, air swirlers, and fuel manifold into a single element. The multipoint concept combustor was demonstrated in a 15 sector test. The configuration tested had 36

Detailed characterization of particulate matter emitted by lean-burn gasoline direct injection engine

Energy Technology Data Exchange (ETDEWEB)

Zelenyuk, Alla [Pacific Northwest National Laboratory, Richland, WA, USA; Wilson, Jacqueline [Pacific Northwest National Laboratory, Richland, WA, USA; Imre, Dan [Imre Consulting, Richland, WA, USA; Stewart, Mark [Pacific Northwest National Laboratory, Richland, WA, USA; Muntean, George [Pacific Northwest National Laboratory, Richland, WA, USA; Storey, John [Oak Ridge National Laboratory, Knoxville, TN, USA; Prikhodko, Vitaly [Oak Ridge National Laboratory, Knoxville, TN, USA; Lewis, Samuel [Oak Ridge National Laboratory, Knoxville, TN, USA; Eibl, Mary [Oak Ridge National Laboratory, Knoxville, TN, USA; Parks, Jim [Oak Ridge National Laboratory, Knoxville, TN, USA

2016-11-10

This study presents detailed characterization of the chemical and physical properties of PM emitted by a 2.0L BMW lean-burn turbocharged GDI engine operated under a number of combustion strategies that include lean homogeneous, lean stratified, stoichiometric, and fuel rich conditions. We characterized PM number concentrations, size distributions, and the size, mass, compositions, and effective density of fractal and compact individual exhaust particles. For the fractal particles, these measurements yielded fractal dimension, average diameter of primary spherules, and number of spherules, void fraction, and dynamic shape factors as function of particle size. Overall, the PM properties were shown to vary significantly with engine operation condition. Lean stratified operation yielded the most diesel-like size distribution and the largest PM number and mass concentrations, with nearly all particles being fractal agglomerates composed of elemental carbon with small amounts of ash and organics. In contrast, stoichiometric operation yielded a larger fraction of ash particles, especially at low speed and low load. Three distinct forms of ash particles were observed, with their fractions strongly dependent on engine operating conditions: sub-50 nm ash particles, abundant at low speed and low load, ash-containing fractal particles, and large compact ash particles that significantly contribute to PM mass loadings

Temperature and air-fuel ratio dependent specific heat ratio functions for lean burned and unburned mixture

International Nuclear Information System (INIS)

Ceviz, M.A.; Kaymaz, I.

2005-01-01

The most important thermodynamic property used in heat release calculations for engines is the specific heat ratio. The functions proposed in the literature for the specific heat ratio are temperature dependent and apply at or near stoichiometric air-fuel ratios. However, the specific heat ratio is also influenced by the gas composition in the engine cylinder and especially becomes important for lean combustion engines. In this study, temperature and air-fuel ratio dependent specific heat ratio functions were derived to minimize the error by using an equilibrium combustion model for burned and unburned mixtures separately. After the error analysis between the equilibrium combustion model and the derived functions is presented, the results of the global specific heat ratio function, as varying with mass fraction burned, were compared with the proposed functions in the literature. The results of the study showed that the derived functions are more feasible at lean operating conditions of a spark ignition engine

A comparison between EGR and lean-burn strategies employed in a natural gas SI engine using a two-zone combustion model

Energy Technology Data Exchange (ETDEWEB)

Ibrahim, Amr; Bari, Saiful [Sustainable Energy Centre, School of Advanced Manufacturing and Mechanical Engineering, Univ. of South Australia, Mawson Lakes SA 5095 (Australia)

2009-12-15

Exhaust gas recirculation (EGR) strategy has been recently employed in natural gas SI engines as an alternative to lean burn technique in order to satisfy the increasingly stringent emission standards. However, the effect of EGR on some of engine performance parameters compared to lean burn is not yet quite certain. In the current study, the effect of both EGR and lean burn on natural gas SI engine performance was compared at similar operating conditions. This was achieved numerically by developing a computer simulation of the four-stroke spark-ignition natural gas engine. A two-zone combustion model was developed to simulate the in-cylinder conditions during combustion. A kinetic model based on the extended Zeldovich mechanism was also developed in order to predict NO emission. The combustion model was validated using experimental data and a good agreement between the results was found. It was demonstrated that adding EGR to the stoichiometric inlet charge at constant inlet pressure of 130 kPa decreased power more rapidly than excess air; however, the power loss was recovered by increasing the inlet pressure from 130 kPa at zero dilution to 150 kPa at 20% EGR dilution. The engine fuel consumption increased by 10% when 20% EGR dilution was added at inlet pressure of 150 kPa compared to using 20% air dilution at 130 kPa. However, it was found that EGR dilution strategy is capable of producing extremely lower NO emission than lean burn technique. NO emission was reduced by about 70% when the inlet charge was diluted at a rate of 20% using EGR instead of excess air. (author)

A comparison between EGR and lean-burn strategies employed in a natural gas SI engine using a two-zone combustion model

International Nuclear Information System (INIS)

Ibrahim, Amr; Bari, Saiful

2009-01-01

Exhaust gas recirculation (EGR) strategy has been recently employed in natural gas SI engines as an alternative to lean burn technique in order to satisfy the increasingly stringent emission standards. However, the effect of EGR on some of engine performance parameters compared to lean burn is not yet quite certain. In the current study, the effect of both EGR and lean burn on natural gas SI engine performance was compared at similar operating conditions. This was achieved numerically by developing a computer simulation of the four-stroke spark-ignition natural gas engine. A two-zone combustion model was developed to simulate the in-cylinder conditions during combustion. A kinetic model based on the extended Zeldovich mechanism was also developed in order to predict NO emission. The combustion model was validated using experimental data and a good agreement between the results was found. It was demonstrated that adding EGR to the stoichiometric inlet charge at constant inlet pressure of 130 kPa decreased power more rapidly than excess air; however, the power loss was recovered by increasing the inlet pressure from 130 kPa at zero dilution to 150 kPa at 20% EGR dilution. The engine fuel consumption increased by 10% when 20% EGR dilution was added at inlet pressure of 150 kPa compared to using 20% air dilution at 130 kPa. However, it was found that EGR dilution strategy is capable of producing extremely lower NO emission than lean burn technique. NO emission was reduced by about 70% when the inlet charge was diluted at a rate of 20% using EGR instead of excess air.

Development II of ion current combustion control system. Application to the lean burn system of the micro vehicle engine; Ion denryu wo mochiita nensho seigyo system no kaihatsu. 2. Keijidosha engine wo mochiita lean burn eno oyo

Energy Technology Data Exchange (ETDEWEB)

Iida, T; Asano, M; Kajitani, M; Kuma, t; Morinaga, Y [Daihatsu Motor Co. Ltd., Osaka (Japan)

1997-10-01

The lean bum engine has not been introduced into the micro vehicle so far because of the low cost requirement and small displacement, in spite of it is one of the effective solutions which increase the fuel economy. By the way, we had already reported in the former paper that we developed the ion current combustion control system the architecture of which is cheaper than the other system. In this paper, we described the way how the above system is applied to the lean burn system of the micro vehicle engine and also we reported the gain of fuel economy and the exhaust emission level. 5 refs., 11 figs., 2 tabs.

Multi-stage selective catalytic reduction of NOx in lean burn engine exhaust

Energy Technology Data Exchange (ETDEWEB)

Penetrante, B.M.; Hsaio, M.C.; Merritt, B.T.; Vogtlin, G.E. [Lawrence Livermore National Lab., CA (United States)

1997-12-31

Many studies suggest that the conversion of NO to NO{sub 2} is an important intermediate step in the selective catalytic reduction (SCR) of NO{sub x} to N{sub 2}. Some effort has been devoted to separating the oxidative and reductive functions of the catalyst in a multi-stage system. This method works fine for systems that require hydrocarbon addition. The hydrocarbon has to be injected between the NO oxidation catalyst and the NO{sub 2} reduction catalyst; otherwise, the first-stage oxidation catalyst will also oxidize the hydrocarbon and decrease its effectiveness as a reductant. The multi-stage catalytic scheme is appropriate for diesel engine exhausts since they contain insufficient hydrocarbons for SCR, and the hydrocarbons can be added at the desired location. For lean-burn gasoline engine exhausts, the hydrocarbons already present in the exhausts will make it necessary to find an oxidation catalyst that can oxidize NO to NO{sub 2} but not oxidize the hydrocarbon. A plasma can also be used to oxidize NO to NO{sub 2}. Plasma oxidation has several advantages over catalytic oxidation. Plasma-assisted catalysis can work well for both diesel engine and lean-burn gasoline engine exhausts. This is because the plasma can oxidize NO in the presence of hydrocarbons without degrading the effectiveness of the hydrocarbon as a reductant for SCR. In the plasma, the hydrocarbon enhances the oxidation of NO, minimizes the electrical energy requirement, and prevents the oxidation of SO{sub 2}. This paper discusses the use of multi-stage systems for selective catalytic reduction of NO{sub x}. The multi-stage catalytic scheme is compared to the plasma-assisted catalytic scheme.

Cellular burning in lean premixed turbulent hydrogen-air flames: Coupling experimental and computational analysis at the laboratory scale

International Nuclear Information System (INIS)

Day, M S; Bell, J B; Beckner, V E; Lijewski, M J; Cheng, R K; Tachibana, S

2009-01-01

One strategy for reducing US dependence on petroleum is to develop new combustion technologies for burning the fuel-lean mixtures of hydrogen or hydrogen-rich syngas fuels obtained from the gasification of coal and biomass. Fuel-flexible combustion systems based on lean premixed combustion have the potential for dramatically reducing pollutant emissions in transportation systems, heat and stationary power generation. However, lean premixed flames are highly susceptible to fluid-dynamical combustion instabilities making robust and reliable systems difficult to design. Low swirl burners are emerging as an important technology for meeting design requirements in terms of both reliability and emissions for next generation combustion devices. In this paper, we present simulations of a lean, premixed hydrogen flame stabilized on a laboratory-scale low swirl burner. The simulations use detailed chemistry and transport without incorporating explicit models for turbulence or turbulence/chemistry interaction. Here we discuss the overall structure of the flame and compare with experimental data. We also use the simulation data to elucidate the characteristics of the turbulent flame interaction and how this impacts the analysis of experimental measurements.

Model reduction of a lean NOx trap catalyst model

NARCIS (Netherlands)

Nauta, K.M.

2008-01-01

The desire to increase fuel efficiency and reduce carbon dioxide emissions of vehicles has led to an increased use of vehicles equipped with lean-burn engines, such as diesel and lean-burn gasoline engines. This type of engine uses excess oxygen when compared to the amount required to

The Effect of Humidity on the Knock Behavior in a Medium BMEP Lean-Burn High-Speed Gas Engine

NARCIS (Netherlands)

van Essen, Vincent Martijn; Gersen, Sander; van Dijk, Gerco; Mundt, Torsten; Levinsky, Howard

2016-01-01

The effects of air humidity on the knock characteristics of fuels are investigated in a lean-burn, high-speed medium BMEP engine fueled with a CH4 + 4.7 mole% C3H8 gas mixture. Experiments are carried out with humidity ratios ranging from 4.3 to 11 g H2O/kg dry air. The measured pressure profiles at

Lean-burn engines UHC emission reduction

Energy Technology Data Exchange (ETDEWEB)

Karll, B.; Kristensen, P.G.; Nielsen, M.; Iskov, H. [Danish Gas Technology Centre a/s (Denmark); Broe Bendtsen, A.; Glarborg, P.; Dam-Johansen, K. [Technical University of Denmark. CHEC, Department of Chemical Engineering (Denmark)

1999-04-01

at increased NO{sub x} levels and the results show that increased NO{sub x} levels improve the UHC conversion in the exhaust reactor. The process is found to be very dependent on actual NO{sub x} levels and the exhaust reactor temperature. The exhaust temperature from lean burn engines is in the range from 450 to 550 deg. C depending on the engine settings and type. The conclusion from the tests shows that only if the temperature in the exhaust system is raised, it will be possible to use the NO{sub x} enhanced UHC oxidation process for post oxidation. Injection of hydrogen peroxide caused a significant reduction in the stack emission of UHC by conversion of UHC at conditions where the exhaust reactor otherwise was unable to oxidise UHC. The stack emission of UHC was reduced by 40-60% during test engine conditions. (EHS) EFP-96; 14 refs.

Lean-burn engines UHC emission reduction

International Nuclear Information System (INIS)

Karll, B.; Kristensen, P.G.; Nielsen, M.; Iskov, H.; Broe Bendtsen, A.; Glarborg, P.; Dam-Johansen, K.

1999-01-01

the results show that increased NO x levels improve the UHC conversion in the exhaust reactor. The process is found to be very dependent on actual NO x levels and the exhaust reactor temperature. The exhaust temperature from lean burn engines is in the range from 450 to 550 deg. C depending on the engine settings and type. The conclusion from the tests shows that only if the temperature in the exhaust system is raised, it will be possible to use the NO x enhanced UHC oxidation process for post oxidation. Injection of hydrogen peroxide caused a significant reduction in the stack emission of UHC by conversion of UHC at conditions where the exhaust reactor otherwise was unable to oxidise UHC. The stack emission of UHC was reduced by 40-60% during test engine conditions. (EHS) EFP-96; 14 refs

Plasma-assisted heterogeneous catalysis for NOx reduction in lean-burn engine exhaust

Energy Technology Data Exchange (ETDEWEB)

Penetrante, B.M.; Hsaio, M.C.; Merritt, B.T.; Vogtlin, G.E. [Lawrence Livermore National Lab., CA (United States); Wan, C.Z.; Rice, G.W.; Voss, K.E. [Engelhard Corp., Iselin, NJ (United States)

1997-12-31

This paper discusses the combination of a plasma with a catalyst to improve the reduction of NO{sub x} under lean-burn conditions. The authors have been investigating the effects of a plasma on the NO{sub x} reduction activity and temperature operating window of various catalytic materials. One of the goals is to develop a fundamental understanding of the interaction between the gas-phase plasma chemistry and the heterogeneous chemistry on the catalyst surface. The authors have observed that plasma assisted heterogeneous catalysis can facilitate NO{sub x} reduction under conditions that normally make it difficult for either the plasma or the catalyst to function by itself. By systematically varying the plasma electrode and catalyst configuration, they have been able to elucidate the process by which the plasma chemistry affects the chemical reduction of NO{sub x} on the catalyst surface. They have discovered that the main effect of the plasma is to induce the gas-phase oxidation of NO to NO{sub 21}. The reduction of NO{sub x} to N{sub 2} is then accomplished by heterogeneous reaction of O with activated hydrocarbons on the catalyst surface. The use of a plasma opens the opportunity for a new class of catalysts that are potentially more durable, more active, more selective and more sulfur-tolerant compared to conventional lean-NO{sub x} catalysts.

Selective NOx Recirculation for Stationary Lean-Burn Natural Gas Engines

Energy Technology Data Exchange (ETDEWEB)

Nigel Clark; Gregory Thompson; Richard Atkinson; Richard Turton; Chamila Tissera; Emre Tatli; Andy Zimmerman

2005-12-28

Selective NOx Recirculation (SNR) involves cooling the engine exhaust gas and then adsorbing the oxides of nitrogen (NOx) from the exhaust stream, followed by the periodic desorption of NOx. By returning the desorbed, concentrated NOx into the engine intake and through the combustion chamber, a percentage of the NOx is decomposed during the combustion process. An initial study of NOx decomposition during lean-burn combustion was concluded in 2004 using a 1993 Cummins L10G 240hp natural gas engine. It was observed that the air/fuel ratio, injected NO (nitric oxide) quantity and engine operating points affected NOx decomposition rates of the engine. Chemical kinetic modeling results were also used to determine optimum NOx decomposition operating points and were published in the 2004 annual report. A NOx decomposition rate of 27% was measured from this engine under lean-burn conditions while the software model predicted between 35-42% NOx decomposition for similar conditions. A later technology 1998 Cummins L10G 280hp natural gas engine was procured with the assistance of Cummins Inc. to replace the previous engine used for 2005 experimental research. The new engine was equipped with an electronic fuel management system with closed-loop control that provided a more stable air/fuel ratio control and improved the repeatability of the tests. The engine was instrumented with an in-cylinder pressure measurement system and electronic controls, and was adapted to operate over a range of air/fuel ratios. The engine was connected to a newly commissioned 300hp alternating current (AC) motoring dynamometer. The second experimental campaign was performed to acquire both stoichiometric and slightly rich (0.97 lambda ratio) burn NOx decomposition rates. Effects of engine load and speed on decomposition were quantified, but Exhaust Gas Recirculation (EGR) was not varied independently. Decomposition rates of up to 92% were demonstrated. Following recommendations at the 2004 ARES peer

Investigation of combustion and thermodynamic performance of a lean burn catalytic combustion gas turbine system

International Nuclear Information System (INIS)

Yin Juan; Weng Yiwu

2011-01-01

The goals of this research were to investigate the combustion and thermodynamic performance of a lean burn catalytic combustion gas turbine. The characteristics of lean burn catalytic combustion were investigated by utilising 1D heterogeneous plug flow model which was validated by experiments. The effects of operating parameters on catalytic combustion were numerically analysed. The system models were built in ASPEN Plus and three independent design variables, i.e. compressor pressure ratio (PR), regenerator effectiveness (RE) and turbine inlet temperature (TIT) were selected to analyse the thermodynamic performance of the thermal cycle. The main results show that: simulations from 1D heterogeneous plug flow model can capture the trend of catalytic combustion and describe the behavior of the catalytic monolith in detail. Inlet temperature is the most significant parameter that impacts operation of the catalytic combustor. When TIT and RE are constant, the increase of PR results in lowering the inlet temperature of the catalytic combustor, which results in decreasing methane conversion. The peak thermal efficiency and the optimal PR at a constant TIT increase with the increase of TIT; and at the constant PR, the thermal efficiency increases with the increase of TIT. However, with lower TIT conditions, the optimal PR and the peak efficiency at a constant TIT of the LBCCGT cycle are relative low to that of the conventional cycle. When TIT and PR are constant, the decrease of RE may result in lower methane conversion. The influences of RE on the methane conversion and the thermal efficiency are more significant at higher PRs. The higher thermal efficiency for the lower RE is achieved at lower PR.

Effects of spark plug configuration on combustion and emission characteristics of a LPG fuelled lean burn SI engine

Science.gov (United States)

Ravi, K.; Khan, Manazir Ahmed; Pradeep Bhasker, J.; Porpatham, E.

2017-11-01

Introduction of technological innovation in automotive engines in reducing pollution and increasing efficiency have been under contemplation. Gaseous fuels have proved to be a promising way to reduce emissions in Spark Ignition (SI) engines. In particular, LPG settled to be a favourable fuel for SI engines because of their higher hydrogen to carbon ratio, octane rating and lower emissions. Wide ignition limits and efficient combustion characteristics make LPG suitable for lean burn operation. But lean combustion technology has certain drawbacks like poor flame propagation, cyclic variations etc. Based on copious research it was found that location, types and number of spark plug significantly influence in reducing cyclic variations. In this work the influence of single and dual spark plugs of conventional and surface discharge electrode type were analysed. Dual surface discharge electrode spark plug enhanced the brake thermal efficiency and greatly reduced the cyclic variations. The experimental results show that rate of heat release and pressure rise was more and combustion duration was shortened in this configuration. On the emissions front, the NOx emission has increased whereas HC and CO emissions were reduced under lean condition.

Investigation on the lean combustion performance of a hydrogen-enriched n-butanol engine

International Nuclear Information System (INIS)

Zhang, Bo; Ji, Changwei; Wang, Shuofeng

2017-01-01

Highlights: • H_2 addition avails improving thermal efficiency of n-butanol engines. • Lean burn limit of n-butanol engine is extended by H_2 addition. • H_2 addition shortens the n-butanol engine combustion duration. • HC and CO from the n-butanol engine are decreased by H_2 addition. - Abstract: n-Butanol is a feasible fuel candidate for spark-ignition engines. The current paper carried out an experiment to explore effects of hydrogen addition on further improving the performance of a n-butanol engine under the part load and lean conditions. Within the test, the engine intake pressure and speed were respectively kept at 61.5 kPa and 1400 rpm. The volumetric fractions of hydrogen in the total intake gas (hydrogen + air) were constrained at 0 and 3%, respectively. Under a certain hydrogen blending level, the global excess air ratio of in-cylinder charge which was changed from the stoichiometric to near the lean burn limit was adjusted by varying the n-butanol injection duration. The experimental results confirmed that the brake thermal efficiency was heightened and the lean burn limit was extended after the hydrogen addition. Besides, compared with the pure n-butanol combustion, the hydrogen enrichment enables the engine to gain dropped ignition delay and rapid combustion duration. Moreover, CO and HC from the pure n-butanol engine were reduced by the hydrogen addition. NOx were generally reduced when the excess air ratio was raised. This suggested that NOx from the hydrogen-enriched butanol engine could also be controlled by lean combustion.

Simulation of lean premixed turbulent combustion

International Nuclear Information System (INIS)

Bell, J; Day, M; Almgren, A; Lijewski, M; Rendleman, C; Cheng, R; Shepherd, I

2006-01-01

There is considerable technological interest in developing new fuel-flexible combustion systems that can burn fuels such as hydrogen or syngas. Lean premixed systems have the potential to burn these types of fuels with high efficiency and low NOx emissions due to reduced burnt gas temperatures. Although traditional Scientific approaches based on theory and laboratory experiment have played essential roles in developing our current understanding of premixed combustion, they are unable to meet the challenges of designing fuel-flexible lean premixed combustion devices. Computation, with its ability to deal with complexity and its unlimited access to data, has the potential for addressing these challenges. Realizing this potential requires the ability to perform high fidelity simulations of turbulent lean premixed flames under realistic conditions. In this paper, we examine the specialized mathematical structure of these combustion problems and discuss simulation approaches that exploit this structure. Using these ideas we can dramatically reduce computational cost, making it possible to perform high-fidelity simulations of realistic flames. We illustrate this methodology by considering ultra-lean hydrogen flames and discuss how this type of simulation is changing the way researchers study combustion

Performance of a hydrogen-enriched ethanol engine at unthrottled and lean conditions

International Nuclear Information System (INIS)

Zhang, Bo; Ji, Changwei; Wang, Shuofeng

2016-01-01

Highlights: • H_2 addition eased cyclic variation of ethanol engine at unthrottled condition. • H_2-blended ethanol engine gains better efficiency at lean conditions. • Bmep of H_2-blended ethanol engine could be controlled by lean burning. • H_2 addition results in reduced exhaust loss and HC emissions. - Abstract: Concerning the throttling loss under part load conditions, it is feasible to further improve the engine thermal efficiency through operating the engine under the unthrottled condition and controlling its load by changing the excess air ratio. However, the narrow flammability of ethanol may lead the ethanol engine to encounter high cyclic variations under unthrottled and lean conditions. The addition of hydrogen is potentially helpful for solving this problem. In this test, the engine was run under an speed of 1400 rpm and unthrottled conditions. The hydrogen volume fractions in the intake were respectively kept at 0% and 3%. For a given hydrogen blending level, the ethanol flow rate was reduced to enable the engine to run under lean conditions. The results showed that the engine efficiency was improved with the blending of hydrogen. The highest thermal efficiency was improved by 6.07% after blending 3% hydrogen to the intake air. The addition of hydrogen could increase the engine torque output at lean conditions. Both cooling and exhaust losses were decreased after the hydrogen enrichment while adopting the lean combustion strategy. The hydrogen addition contributed to the extended lean burn limit and decreased cyclic variation under lean conditions. HC and CO emissions were decreased whereas NOx emissions were increased after the blending of hydrogen.

Air-fuel ratio control of a lean burn Si engine using fuzzy self tuning method

International Nuclear Information System (INIS)

Akhlaghi, M.; Bakhtiari Nejad, F.; Azadi, S.

2000-01-01

Reducing the exhaust emission of an spark ignition engine by means of engine modifications requires consideration of the effects of these modifications on the variations of crankshaft torque and the engine roughness respectively. Only if the roughness does not exceed a certain level the vehicle do not begin to surge. This paper presents a method for controlling the air-fuel ratio for a lean burn engine. Fuzzy rules and reasoning are utilized on-line to determine the control parameters. The main advantages of this method are simple structure and robust performance in a wide range of operating conditions. A non-linear model of an Si engine with the engine torque irregularity simulation is used in this study

Catalytic reduction of methane/unburned hydrocarbons in smoke from lean-burn gas engines

International Nuclear Information System (INIS)

Wit, Jan de.

1999-01-01

The aim of this project has been: To describe the flue gas conditions of typical stationary gas engines for cogeneration; To evaluate the predominant causes of deactivation of oxidation catalysts under realistic operation conditions; To develop improved long-term stable oxidation catalysts; To evaluate alternative catalyst-based methane reduction technologies. Most gas engines for stationary purposes are efficient lean-burn gas engines. Both the high efficiency and the very lean operation lead to low exhaust temperatures. However, there is now a tendency to design engines with un-cooled exhaust manifolds. This leads to higher shaft efficiency and increases the exhaust temperature. Exhaust gas composition and temperatures during continuous operation and start/stops are given in this report. Analyses have been made of catalyst samples to find predominant causes for oxidation catalyst deactivation. The analyses have shown that the presence of sulphur dioxide in the flue gas causes sulphur poisoning on the active catalyst surface. This effect is dependent on both the catalyst formulation and the catalyst support material composition. Neither sintering, nor other poisoning components than sulphur have been on the examined catalyst samples. The sulphur dioxide in the exhaust is a result of the sulphur in the odorisation additive used in the natural gas (approx. 10 mg/n 3 m THT) and of the sulphur present in combusted lubrication oil. These sources leads to a level of approx. 0.3 - 0.6 ppm (vol) SO 2 in the exhaust gas. Based on a large number of laboratory tests, a new oxidation catalyst formulation has been developed and successfully tested over 5000 hours of operation at a commercial cogeneration plant. This long-term testing has been additionally supplemented by short-term testings at test sites to see performance under other operation conditions. It has been shown that a rise in flue gas temperature (from e.g. 450 deg. C) will significantly reduce the necessary

Preparation Effects on the Performance of Silica-Doped Hydrous Titanium Oxide (HTO:Si)-Supported Pt Catalysts for Lean-Burn NOx Reduction by Hydrocarbons; TOPICAL

International Nuclear Information System (INIS)

GARDNER, TIMOTHY J.; MCLAUGHLIN, LINDA I.; MOWERY, DEBORAH L.; SANDOVAL, RONALD S.

2002-01-01

This report describes the development of bulk hydrous titanium oxide (HTO)- and silica-doped hydrous titanium oxide (HTO:Si)-supported Pt catalysts for lean-burn NOx catalyst applications. The effects of various preparation methods, including both anion and cation exchange, and specifically the effect of Na content on the performance of Pt/HTO:Si catalysts, were evaluated. Pt/HTO:Si catalysts with low Na content ( and lt; 0.5 wt.%) were found to be very active for NOx reduction in simulated lean-burn exhaust environments utilizing propylene as the major reductant species. The activity and performance of these low Na Pt/HTO:Si catalysts were comparable to supported Pt catalysts prepared using conventional oxide or zeolite supports. In ramp down temperature profile test conditions, Pt/HTO:Si catalysts with Na contents in the range of 3-5 wt.% showed a wide temperature window of appreciable NOx conversion relative to low Na Pt/HTO:Si catalysts. Full reactant species analysis using both ramp up and isothermal test conditions with the high Na Pt/HTO:Si catalysts, as well as diffuse reflectance FTIR studies, showed that this phenomenon was related to transient NOx storage effects associated with NaNO(sub 2)/NaNO(sub 3) formation. These nitrite/nitrate species were found to decompose and release NOx at temperatures above 300 C in the reaction environment (ramp up profile). A separate NOx uptake experiment at 275 C in NO/N(sub 2)/O(sub 2) showed that the Na phase was inefficiently utilized for NOx storage. Steady state tests showed that the effect of increased Na content was to delay NOx light-off and to decrease the maximum NOx conversion. Similar results were observed for high K Pt/HTO:Si catalysts, and the effects of high alkali content were found to be independent of the sample preparation technique. Catalyst characterization (BET surface area, H(sub 2) chemisorption, and transmission electron microscopy) was performed to elucidate differences between the HTO- and HTO

Comparison of muscle/lean mass measurement methods: correlation with functional and biochemical testing.

Science.gov (United States)

Buehring, B; Siglinsky, E; Krueger, D; Evans, W; Hellerstein, M; Yamada, Y; Binkley, N

2018-03-01

DXA-measured lean mass is often used to assess muscle mass but has limitations. Thus, we compared DXA lean mass with two novel methods-bioelectric impedance spectroscopy and creatine (methyl-d3) dilution. The examined methodologies did not measure lean mass similarly and the correlation with muscle biomarkers/function varied. Muscle function tests predict adverse health outcomes better than lean mass measurement. This may reflect limitations of current mass measurement methods. Newer approaches, e.g., bioelectric impedance spectroscopy (BIS) and creatine (methyl-d3) dilution (D3-C), may more accurately assess muscle mass. We hypothesized that BIS and D3-C measured muscle mass would better correlate with function and bone/muscle biomarkers than DXA measured lean mass. Evaluations of muscle/lean mass, function, and serum biomarkers were obtained in older community-dwelling adults. Mass was assessed by DXA, BIS, and orally administered D3-C. Grip strength, timed up and go, and jump power were examined. Potential muscle/bone serum biomarkers were measured. Mass measurements were compared with functional and serum data using regression analyses; differences between techniques were determined by paired t tests. Mean (SD) age of the 112 (89F/23M) participants was 80.6 (6.0) years. The lean/muscle mass assessments were correlated (.57-.88) but differed (p Lean mass measures were unrelated to the serum biomarkers measured. These three methodologies do not similarly measure muscle/lean mass and should not be viewed as being equivalent. Functional tests assessing maximal muscle strength/power (grip strength and jump power) correlated with all mass measures whereas gait speed was not. None of the selected serum measures correlated with mass. Efforts to optimize muscle mass assessment and identify their relationships with health outcomes are needed.

Cyclic variations of fuel-droplet distribution during the early intake stroke of a lean-burn stratified-charge spark-ignition engine

Energy Technology Data Exchange (ETDEWEB)

Aleiferis, P.G. [Imperial College London, Department of Mechanical Engineering, London (United Kingdom); University College London, Department of Mechanical Engineering, London (United Kingdom); Hardalupas, Y.; Taylor, A.M.K.P. [Imperial College London, Department of Mechanical Engineering, London (United Kingdom); Ishii, K. [Honda International Technical School, Saitama (Japan); Urata, Y. [Tochigi R and D Centre, Honda R and D Co., Ltd, Tochigi (Japan)

2005-11-01

Lean-burn spark-ignition engines exhibit higher efficiency and lower specific emissions in comparison with stoichiometrically charged engines. However, as the air-to-fuel (A/F) ratio of the mixture is made leaner than stoichiometric, cycle-by-cycle variations in the early stages of in-cylinder combustion, and subsequent indicated mean effective pressure (IMEP), become more pronounced and limit the range of lean-burn operation. Viable lean-burn engines promote charge stratification, the mixture near the spark plug being richer than the cylinder volume averaged value. Recent work has shown that cycle-by-cycle variations in the early stages of combustion in a stratified-charge engine can be associated with variations in both the local value of A/F ratio near the spark plug around ignition timing, as well as in the volume averaged value of the A/F ratio. The objective of the current work was to identify possible sources of such variability in A/F ratio by studying the in-cylinder field of fuel-droplet distribution during the early intake stroke. This field was visualised in an optical single-cylinder 4-valve pentroof-type spark-ignition engine by means of laser-sheet illumination in planes parallel to the cylinder head gasket 6 and 10 mm below the spark plug. The engine was run with port-injected isooctane at 1500 rpm with 30% volumetric efficiency and air-to-fuel ratio corresponding to both stoichiometric firing (A/F=15, {phi} =1.0) and mixture strength close to the lean limit of stable operation (A/F=22, {phi} =0.68). Images of Mie intensity scattered by the cloud of fuel droplets were acquired on a cycle-by-cycle basis. These were studied in order to establish possible correlations between the cyclic variations in size, location and scattered-light intensity of the cloud of droplets with the respective variations in IMEP. Because of the low level of Mie intensity scattered by the droplets and because of problems related to elastic scattering on the walls of the

Multi-Element Lean Direct Injection Combustor Module, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — We propose to develop a Multi-Element Lean Direct Injection, ME-LDI, Combustion concept with the following innovative features: 1. Independent, mini burning zones...

One-step reduced kinetics for lean hydrogen-air deflagration

Energy Technology Data Exchange (ETDEWEB)

Fernandez-Galisteo, D.; Sanchez, A.L. [Area de Mecanica de Fluidos, Univ. Carlos III de Madrid, Leganes 28911 (Spain); Linan, A. [ETSI Aeronauticos, Pl. Cardenal Cisneros 3, Madrid 28040 (Spain); Williams, F.A. [Dept. of Mechanical and Aerospace Engineering, University of California San Diego, La Jolla, CA 92093-0411 (United States)

2009-05-15

A short mechanism consisting of seven elementary reactions, of which only three are reversible, is shown to provide good predictions of hydrogen-air lean-flame burning velocities. This mechanism is further simplified by noting that over a range of conditions of practical interest, near the lean flammability limit all reaction intermediaries have small concentrations in the important thin reaction zone that controls the hydrogen-air laminar burning velocity and therefore follow a steady state approximation, while the main species react according to the global irreversible reaction 2H{sub 2} + O{sub 2} {yields} 2H{sub 2}O. An explicit expression for the non-Arrhenius rate of this one-step overall reaction for hydrogen oxidation is derived from the seven-step detailed mechanism, for application near the flammability limit. The one-step results are used to calculate flammability limits and burning velocities of planar deflagrations. Furthermore, implications concerning radical profiles in the deflagration and reasons for the success of the approximations are clarified. It is also demonstrated that adding only two irreversible direct recombination steps to the seven-step mechanism accurately reproduces burning velocities of the full detailed mechanism for all equivalence ratios at normal atmospheric conditions and that an eight-step detailed mechanism, constructed from the seven-step mechanism by adding to it the fourth reversible shuffle reaction, improves predictions of O and OH profiles. The new reduced-chemistry descriptions can be useful for both analytical and computational studies of lean hydrogen-air flames, decreasing required computation times. (author)

Furniture wood wastes: Experimental property characterisation and burning tests

International Nuclear Information System (INIS)

Tatano, Fabio; Barbadoro, Luca; Mangani, Giovanna; Pretelli, Silvia; Tombari, Lucia; Mangani, Filippo

2009-01-01

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected 'raw' and primarily 'engineered' ('composite') wood wastes. The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in 'engineered' wood wastes as compared with 'raw' wood wastes; and relatively high energy content values of 'engineered' wood wastes (ranging on the whole from 3675 to 5105 kcal kg -1 for HHV, and from 3304 to 4634 kcal kg -1 for LHV). The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in 'engineered' wood burning tests of pyrroles and amines, as well as the additional presence (as compared with 'raw' wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon. Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in 'engineered' wood burning tests as compared with 'raw' wood burning test; and considerable generation of the respirable PM 1 fraction during incomplete industrial wood burning.

A Laser Spark Plug Ignition System for a Stationary Lean-Burn Natural Gas Reciprocating Engine

Energy Technology Data Exchange (ETDEWEB)

McIntyre, D. L. [West Virginia Univ., Morgantown, WV (United States)

2007-05-01

To meet the ignition system needs of large bore, high pressure, lean burn, natural gas engines a side pumped, passively Q-switched, Nd:YAG laser was developed and tested. The laser was designed to produce the optical intensities needed to initiate ignition in a lean burn, high compression engine. The laser and associated optics were designed with a passive Q-switch to eliminate the need for high voltage signaling and associated equipment. The laser was diode pumped to eliminate the need for high voltage flash lamps which have poor pumping efficiency. The independent and dependent parameters of the laser were identified and explored in specific combinations that produced consistent robust sparks in laboratory air. Prior research has shown that increasing gas pressure lowers the breakdown threshold for laser initiated ignition. The laser has an overall geometry of 57x57x152 mm with an output beam diameter of approximately 3 mm. The experimentation used a wide range of optical and electrical input parameters that when combined produced ignition in laboratory air. The results show a strong dependence of the output parameters on the output coupler reflectivity, Q-switch initial transmission, and gain media dopant concentration. As these three parameters were lowered the output performance of the laser increased leading to larger more brilliant sparks. The results show peak power levels of up to 3MW and peak focal intensities of up to 560 GW/cm². Engine testing was performed on a Ricardo Proteus single cylinder research engine. The goal of the engine testing was to show that the test laser performs identically to the commercially available flashlamp pumped actively Q-switched laser used in previous laser ignition testing. The engine testing consisted of a comparison of the in-cylinder, and emissions behavior of the engine using each of the lasers as an ignition system. All engine parameters were kept as constant as possilbe while the equivalence ratio (fueling

Introduction to Lean Canvas Transformation Models and Metrics in Software Testing

Directory of Open Access Journals (Sweden)

Nidagundi Padmaraj

2016-05-01

Full Text Available Software plays a key role nowadays in all fields, from simple up to cutting-edge technologies and most of technology devices now work on software. Software development verification and validation have become very important to produce the high quality software according to business stakeholder requirements. Different software development methodologies have given a new dimension for software testing. In traditional waterfall software development software testing has approached the end point and begins with resource planning, a test plan is designed and test criteria are defined for acceptance testing. In this process most of test plan is well documented and it leads towards the time-consuming processes. For the modern software development methodology such as agile where long test processes and documentations are not followed strictly due to small iteration of software development and testing, lean canvas transformation models can be a solution. This paper provides a new dimension to find out the possibilities of adopting the lean transformation models and metrics in the software test plan to simplify the test process for further use of these test metrics on canvas.

Study of gas (CNG) SI engine with pre-chamber. Improvement of the indicated thermal efficiency on lean mixture with EGR and supercharging; Fukushitsushiki hibana tenka asshuku tennen gas (CNG) engine ni kansuru kenkyu. Kakyu to EGR ni yoru kihakuiki no netsukoritsu kaizen

Energy Technology Data Exchange (ETDEWEB)

Yonetani, H.; Fukutani, I. [Polytechnic University, Kanagawa (Japan)

1998-10-15

As lean burn of compressed natural gas (CNG) is applied to conventional gasoline engines, a combustion period largely increases, resulting in large combustion fluctuation and low thermal efficiency. Heterogeneous spacial air/fuel ratios also have an effect on combustion in lean burn area. By preparing a pre-chamber for a combustion chamber of high- compression ratio CNG pre-mixing SI engines to utilize premixture turbulence, rapid flame propagation is obtained in lean burn area, resulting high combustion performance. Furthermore, study was made on improvement of combustion performance in lean burn area under various compression ratios, intake pressures, pre-chamber shapes and EGR ratios. As a result, lean burn operation at high intake pressure by supercharging showed possible improvement of a thermal efficiency and expansion of inflammable limits. Higher thermal efficiency in lean burn area was also obtained by using higher compression ratios considering heat loss. Although EGR was effective in controlling NOx formed in lean burn area, strict control of both air excess rate and EGR rate was required to prevent lower thermal efficiency. 2 refs., 8 figs., 1 tab.

Conditioning of data for cyclic variation of IMEP under lean burn operation in a spark-ignition engine; Hibana tenka kikan no kihaku nensho untenji ni okeru zushi heikin yuko atsuryoku no hendo

Energy Technology Data Exchange (ETDEWEB)

Ishii, K.; Urata, Y.; Yoshida, K.; Ono, t. [Honda Motor Co. Ltd., Tokyo (Japan)

1997-07-25

In this study, we investigated the relationship of indicated mean effective pressure (IMEP) for a spark ignition engine under lean combustion with the cyclic variation of mass fraction burned by measuring the energy release from the spark plug, intensity of the light emission from the flame and the cylinder pressure at the same time. In order to minimized an error in the initial and late combustion sages of the mass fraction burned to be obtained by cylinder pressure, spark plug energy and intensity of light emission were measured. As a result, it was found that there are three main causes of cyclic variation of IMEP. These consist of the burning speed during the initial stage of combustion, variation in the total mass fraction burned, and variation of the late burning during the late expansion stroke. Thus, we determined that there is a favorable interrelationship between the IMEPs and the corrected mass fraction burned. 13 refs., 9 figs., 1 tab.

Effects of different duration exercise programs in children with severe burns.

Science.gov (United States)

Clayton, Robert P; Wurzer, Paul; Andersen, Clark R; Mlcak, Ronald P; Herndon, David N; Suman, Oscar E

2017-06-01

Burns lead to persistent and detrimental muscle breakdown and weakness. Standard treatment at our institution includes a voluntary 12-week rehabilitative exercise program to limit and reverse the effects of increased muscle catabolism. In the present work, we investigated if different durations of exercise, 6 or 12 weeks, produce comparable improvements in muscle strength, body composition, and cardiopulmonary fitness. We prospectively enrolled and randomized patients with ≥30% total body surface area (TBSA) burned to receive 6 or 12 weeks of exercise rehabilitation. Patients were evaluated for muscle strength, oxygen consumption capacity, and lean body mass at discharge (n=42) and after exercise. After 6 weeks (n=18) or 12 weeks (n=24) of exercise training, leg muscle strength was assessed as peak torque per body weight using a Biodex isokinetic dynamometer. Oxygen consumption capacity, measured as peak VO 2 , was studied using a standard treadmill-based test, and lean body mass was determined using dual-energy X-ray absorptiometry. Significant improvements in muscle strength, peak VO 2 , and lean body mass were seen after 6 weeks of exercise training (pburn patients. However, continuation of at- or near-home cardiopulmonary training following the 6 weeks of at-hospital rehabilitation may be useful. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Wafer-level testing and test during burn-in for integrated circuits

CERN Document Server

Bahukudumbi, Sudarshan

2010-01-01

Wafer-level testing refers to a critical process of subjecting integrated circuits and semiconductor devices to electrical testing while they are still in wafer form. Burn-in is a temperature/bias reliability stress test used in detecting and screening out potential early life device failures. This hands-on resource provides a comprehensive analysis of these methods, showing how wafer-level testing during burn-in (WLTBI) helps lower product cost in semiconductor manufacturing.Engineers learn how to implement the testing of integrated circuits at the wafer-level under various resource constrain

A Second Generation Swirl-Venturi Lean Direct Injection Combustion Concept

Science.gov (United States)

Tacina, Kathleen M.; Chang, Clarence T.; He, Zhuohui Joe; Lee, Phil; Dam, Bidhan; Mongia, Hukam

2014-01-01

A low-NO (sub x) aircraft gas turbine engine combustion concept was developed and tested. The concept is a second generation swirl-venturi lean direct injection (SV-LDI) concept. LDI is a lean-burn combustion concept in which the fuel is injected directly into the flame zone. Three second generation SV-LDI configurations were developed. All three were based on the baseline 9-point SV-LDI configuration reported previously. These second generation configurations had better low power operability than the baseline 9-point configuration. Two of these second generation configurations were tested in a NASA Glenn Research Center flametube; these two configurations are called the at dome and 5-recess configurations. Results show that the 5-recess configuration generally had lower NO (sub x) emissions than the flat dome configuration. Correlation equations were developed for the flat dome configuration so that the landing-takeoff NO (sub x) emissions could be estimated. The flat dome landing-takeoff NO (sub x) is estimated to be 87-88 percent below the CAEP/6 standards, exceeding the ERA project goal of 75 percent reduction.

Ares Launch Vehicles Lean Practices Case Study

Science.gov (United States)

Doreswamy, Rajiv, N.; Self, Timothy A.

2008-01-01

This viewgraph presentation describes test strategies and lean philisophies and practices that are applied to Ares Launch Vehicles. The topics include: 1) Testing strategy; 2) Lean Practices in Ares I-X; 3) Lean Practices Applied to Ares I-X Schedule; 4) Lean Event Results; 5) Lean, Six Sigma, and Kaizen Practices in the Ares Projects Office; 6) Lean and Kaizen Success Stories; and 7) Ares Six Sigma Practices.

Lean maturity, lean sustainability

DEFF Research Database (Denmark)

Jørgensen, Frances; Matthiesen, Rikke; Nielsen, Jacob

2007-01-01

. A framework for describing levels of lean capability is presented, based on a brief review of the literature and experiences from 12 Danish companies currently implementing lean. Although still in its emerging phase, the framework contributes to both theory and practice by describing developmental stages......Although lean is rapidly growing in popularity, its implementation is far from problem free and companies may experience difficulties sustaining long term success. In this paper, it is suggested that sustainable lean requires attention to both performance improvement and capability development...... that support lean capability development and consequently, lean sustainability....

TRIGA criticality experiment for testing burn-up calculations

International Nuclear Information System (INIS)

Persic, Andreja; Ravnik, Matjaz; Zagar, Tomaz

1999-01-01

A criticality experiment with partly burned TRIGA fuel is described. 20 wt % enriched standard TRIGA fuel elements initially containing 12 wt % U are used. Their average burn-up is 1.4 MWd. Fuel element burn-up is calculated in 2-D four group diffusion approximation using TRIGLAV code. The burn-up of several fuel elements is also measured by reactivity method. The excess reactivity of several critical and subcritical core configurations is measured. Two core configurations contain the same fuel elements in the same arrangement as were used in the fresh TRIGA fuel criticality experiment performed in 1991. The results of the experiment may be applied for testing the computer codes used for fuel burn-up calculations. (author)

Numerical simulation of nitrogen oxide formation in lean premixed turbulent H2/O2/N2 flames

DEFF Research Database (Denmark)

Day, Marc S.; Bell, John B.; Gao, Xinfeng

2011-01-01

Lean premixed hydrogen flames are thermodiffusively unstable and burn in cellular structures. Within these cellular structures the flame is locally enriched by preferential diffusion of hydrogen, leading to local hotspots that burn more intensely than an idealized flat steady flame at comparable ...

Early deprivation increases high-leaning behavior, a novel anxiety-like behavior, in the open field test in rats.

Science.gov (United States)

Kuniishi, Hiroshi; Ichisaka, Satoshi; Yamamoto, Miki; Ikubo, Natsuko; Matsuda, Sae; Futora, Eri; Harada, Riho; Ishihara, Kohei; Hata, Yoshio

2017-10-01

The open field test is one of the most popular ethological tests to assess anxiety-like behavior in rodents. In the present study, we examined the effect of early deprivation (ED), a model of early life stress, on anxiety-like behavior in rats. In ED animals, we failed to find significant changes in the time spent in the center or thigmotaxis area of the open field, the common indexes of anxiety-like behavior. However, we found a significant increase in high-leaning behavior in which animals lean against the wall standing on their hindlimbs while touching the wall with their forepaws at a high position. The high-leaning behavior was decreased by treatment with an anxiolytic, diazepam, and it was increased under intense illumination as observed in the center activity. In addition, we compared the high-leaning behavior and center activity under various illumination intensities and found that the high-leaning behavior is more sensitive to illumination intensity than the center activity in the particular illumination range. These results suggest that the high-leaning behavior is a novel anxiety-like behavior in the open field test that can complement the center activity to assess the anxiety state of rats. Copyright © 2017 Elsevier Ireland Ltd and Japan Neuroscience Society. All rights reserved.

Performance effect of Lean

DEFF Research Database (Denmark)

Kristensen, Thomas Borup; Israelsen, Poul

2016-01-01

To understand how the practices of Lean affect performance, we tested and validated a system-wide approach using mediating relationships in a structural equation model. We used a cross-sectional survey of 200 Danish companies that indicated that they used Lean. Thus, this study is especially...... relevant to Denmark, but the approach is empirically more generalizable. We show that the effect of Lean standardized flow production practices on performance is mediated by analytical continuous improvement empowerment practices and by delegation of decision rights practices. Thus, standardized flow...... of decision rights. The paper provides evidence that supports the view that middle managers’ actions further enhance performance in Lean companies. The right Lean behavior by middle managers increases the level of analytical continuous improvement empowerment. In total, high-performing Lean companies...

Improving Healthcare through Lean Management

DEFF Research Database (Denmark)

Nielsen, Anders Paarup; Edwards, Kasper

2011-01-01

The ideas and principles from lean management are now widely being adopted within the healthcare sector. The analysis in this paper shows that organizations within healthcare most often only implement a limited set of tools and methods from the lean tool-box. Departing from a theoretical analysis...... of the well-known and universal lean management principles in the context of the healthcare this paper will attempt to formulate and test four hypotheses about possible barriers to the successful implementation of lean management in healthcare. The first hypothesis states that lean management in healthcare....... The paper concludes by discussing the implications of hypothesis two, three, and four for the successful application of lean management within healthcare. Is it concluded that this requires a transformative and contingent approach to lean management where the universal principles of the lean philosophy...

Initial Burn Pan (JMTF) Testing Results

Science.gov (United States)

2016-03-01

burn pan and one located high on the Ex-USS Shadwell. There were also a number of GoPro cameras (3-4) that were positioned to observe specific...locations around the test area. A remote control drone equipped with a GoPro camera was also used to video the third test. All recorded video and still

TRUNK LEAN DURING A SINGLE-LEG SQUAT IS ASSOCIATED WITH TRUNK LEAN DURING PITCHING.

Science.gov (United States)

Plummer, Hillary A; Oliver, Gretchen D; Powers, Christopher M; Michener, Lori A

2018-02-01

Impaired trunk motion during pitching may be a risk factor for upper extremity injuries. Specifically, increased forces about the shoulder and elbow have been observed in pitchers with excessive contralateral trunk lean during pitching. Because of the difficulty in identifying abnormal trunk motions during a high-speed task such as pitching, a clinical screening test is needed to identify pitchers who have impaired trunk motion during pitching. The purpose of this study was to determine the relationship between the degree of lateral trunk lean during the single-leg squat and amount of trunk lean during pitching and if trunk lean during pitching can be predicted from lean during the single-leg squat. Controlled Laboratory Study; Cross-sectional. Seventy-three young baseball pitchers (11.4 ± 1.7 years; 156.3 ± 11.9 cm; 50.5 ± 8.8 kg) participated. An electromagnetic tracking system was used to obtain trunk kinematic data during a single-leg squat task (lead leg) and at maximum shoulder external rotation of a fastball pitch. Pearson correlation coefficients for trunk lean during the single-leg squat and pitching were calculated. A linear regression analysis was performed to determine if trunk lean during pitching can be predicted from lean during the single-leg squat. There was a positive correlation between trunk lean during the single-leg squat and trunk lean during pitching (r = 0.53; plean during the single-leg squat predicted the amount of lateral trunk lean during pitching (R 2 = 0.28; p lean during an SLS and pitching. Trunk lean during the single-leg squat explained 28% of the variance in trunk lean during pitching. Diagnosis, level 3.

Ghrelin receptor controls obesity by fat burning

Science.gov (United States)

Emerging evidence show that brown fat in the body produces heat to burn energy, thus prompting weight loss. Ghrelin is the only known hormone which increases appetite and promotes weight gain. We have reported that mice that lack the receptor which mediates the functions of ghrelin are lean. Our fu...

Lean Manufacturing measurement: The relationships between Lean activities and Lean metrics

Directory of Open Access Journals (Sweden)

Diego Fernando Manotas Duque

2007-01-01

Full Text Available Medición en Lean Manufacturing: Relaciones entre Actividades Lean y Métricas Lean Lean Manufacturing fue desarrollada por Toyota para satisfacer sus necesidades específicas en un mercado restringido y en tiempos de estrechez económica. Estos conceptos han sido estudiados y se ha comprobado su aplicabilidad en una amplia variedad de industrias. El objetivo de este artículo es el de integrar un conjunto de métricas que han sido propuestas por diferentes autores, de tal manera que sean consistentes con las etapas y elementos de implementaciones de Lean Manufacturing. Para lograrlo se presentan dos marcos de referencia para implementaciones Lean y los principales factores de éxito se utilizan como base para proponer métricas que identifiquen el avance en estos factores. Posteriormente se propone una tabla que cruza el impacto de las “Actividades Lean” sobre las métricas, postulando que muchos de los supuestos a priori sobre estos impactos deberían ser precisos. Finalmente se proponen algunas ideas para proyectos de investigación hacia el futuro y posibles extensiones de las aplicaciones propuestas aquí.

A Comparison of Three Second-generation Swirl-Venturi Lean Direct Injection Combustor Concepts

Science.gov (United States)

Tacina, Kathleen M.; Podboy, Derek P.; He, Zhuohui Joe; Lee, Phil; Dam, Bidhan; Mongia, Hukam

2016-01-01

Three variations of a low emissions aircraft gas turbine engine combustion concept were developed and tested. The concept is a second generation swirl-venturi lean direct injection (SV-LDI) concept. LDI is a lean-burn combustion concept in which the fuel is injected directly into the flame zone. All three variations were based on the baseline 9- point SV-LDI configuration reported previously. The three second generation SV-LDI variations are called the 5-recess configuration, the flat dome configuration, and the 9- recess configuration. These three configurations were tested in a NASA Glenn Research Center medium pressure flametube. All three second generation variations had better low power operability than the baseline 9-point configuration. All three configurations had low NO(sub x) emissions, with the 5-recess configuration generally having slightly lower NO(x) than the flat dome or 9-recess configurations. Due to the limitations of the flametube that prevented testing at pressures above 20 atm, correlation equations were developed for the at dome and 9-recess configurations so that the landing-takeoff NO(sub x) emissions could be estimated. The flat dome and 9-recess landing-takeoff NO(x) emissions are estimated to be 81-88% below the CAEP/6 standards, exceeding the project goal of 75% reduction.

An experimental study of a hydrogen-enriched ethanol fueled Wankel rotary engine at ultra lean and full load conditions

International Nuclear Information System (INIS)

Amrouche, F.; Erickson, P.A.; Varnhagen, S.; Park, J.W.

2016-01-01

Highlights: • H_2 was added at the intake of a single-rotor ethanol fueled Wankel engine. • The engine was operating at ultra-lean condition, WOT and 3000 rpm. • H_2 enrichment helps shortening the burn duration, enhance the thermal efficiency and reduce the BSEC. • H_2 addition helps to reduce HC, CO and CO_2 emissions. - Abstract: In this paper, the effect of hydrogen addition to ethanol in a monorotor Wankel engine at wide open throttle position and in an ultra-lean operating regime was experimentally investigated. For this aim, variation of hydrogen enrichment levels on the ethanol engine performance and emissions were considered. Experiments were carried out under a constant engine speed of 3000 rpm and fixed spark timing of 15 °BTDC. The test results showed that hydrogen enrichment improved the combustion process through shortening of the flame development and flame propagation periods and reducing the cyclic variation. Furthermore, the reduction of burn duration with the increase of hydrogen fraction enhances the thermal efficiency, reducing the brake-specific energy consumption, as well as reducing the unburned hydrocarbons emissions of the Wankel engine.

Pilot testing of a burn prevention teaching tool for Amish children.

Science.gov (United States)

Rieman, Mary T; Kagan, Richard J

2012-01-01

Burn prevention education for Amish children is warranted as there are unique risks associated with the Amish lifestyle. Specific educational opportunities are related to scalds, ignition of clothing, and ignition of highly flammable materials. A culturally sensitive burn prevention teaching tool, consisting of a magnetic storyboard, burn safety curriculum, and tests, was developed with the cooperation of one Old Order Amish community. The purpose of this study was to test the effectiveness of the tool in an Amish school. The teacher obtained parental permission and informed assent for the participation of the children. Pretesting was completed before the lessons began. The teacher told stories and arranged the magnets on the storyboard to show burn hazards involving lighters, stoves, kerosene heaters, gasoline-powered engines, and hot liquids used for canning, butchering, mopping, washing clothes, and making lye soap. The children were challenged to rearrange the pieces for a safer situation. Posttesting was performed 2 months after the pretest. Twenty-seven students (grades 1-8) participated. Tests were scored as a percentage of the 33 items answered correctly. The mean pretest score was 62 and the mean posttest score was 83. Statistical analysis using paired t-test demonstrated a highly significant improvement in test scores (P < .0001), with a power of more than 99%. This pilot study demonstrated that the burn prevention teaching tool was effective for improving knowledge in one classroom of Amish children. These results support expanded use and testing of this tool in other Amish schools.

The relative effects of fuel concentration, residual-gas fraction, gas motion, spark energy and heat losses to the electrodes on flame-kernel development in a lean-burn spark ignition engine

Energy Technology Data Exchange (ETDEWEB)

Aleiferis, P.G.; Taylor, A.M.K.P. [Imperial College of Science, Technology and Medicine, London (United Kingdom). Dept. of Mechanical Engineering; Ishii, K. [Honda International Technical School, Saitama (Japan); Urata, Y. [Honda R and D Co., Ltd., Tochigi (Japan). Tochigi R and D Centre

2004-04-01

The potential of lean combustion for the reduction in exhaust emissions and fuel consumption in spark ignition engines has long been established. However, the operating range of lean-burn spark ignition engines is limited by the level of cyclic variability in the early-flame development stage that typically corresponds to the 0-5 per cent mass fraction burned duration. In the current study, the cyclic variations in early flame development were investigated in an optical stratified-charge spark ignition engine at conditions close to stoichiometry [air-to-fuel ratio (A/F) = 15] and to the lean limit of stable operation (A/F = 22). Flame images were acquired through either a pentroof window ('tumble plane' of view) or the piston crown ('swirl plane' of view) and these were processed to calculate the intra-cycle flame-kernel radius evolution. In order to quantify the relative effects of local fuel concentration, gas motion, spark-energy release and heat losses to the electrodes on the flame-kernel growth rate, a zero-dimensional flame-kernel growth model, in conjunction with a one-dimensional spark ignition model, was employed. Comparison of the calculated flame-radius evolutions with the experimental data suggested that a variation in A/F around the spark plug of {delta}(A/F) {approx} 4 or, in terms of equivalence ratio {phi}, a variation in {delta}{phi} {approx} 0.15 at most was large enough to account for 100 per cent of the observed cyclic variability in flame-kernel radius. A variation in the residual-gas fraction of about 20 per cent around the mean was found to account for up to 30 per cent of the variability in flame-kernel radius at the timing of 5 per cent mass fraction burned. The individual effect of 20 per cent variations in the 'mean' in-cylinder velocity at the spark plug at ignition timing was found to account for no more than 20 per cent of the measured cyclic variability in flame kernel radius. An individual effect of

To burn or not to burn

International Nuclear Information System (INIS)

Busch, L.

1993-01-01

While taking a match to an oil slick may sound like the making of a chaotic inferno, emergency response specialists say burning may be the most efficient way to remove large oil spills from the ocean's surface. But tests of this technique are being resisted by environmentalists as well as the Environmental Protection Agency (EPA), which has final authority over the matter. The debate over test burning arose most recently in Alaska when a proposal to spill and then ignite 1,000 barrels of crude on the Arctic Ocean this past summer was rejected by the EPA. The EPA didn't object to the technique or to the notion of burning spilled oil. However, it contends that it's not necessary to spill thousands of gallons of oil to conduct tests, and unnecessarily pollute the environment, when plenty of oil is already available from accidental spills. Researchers disagree, claiming they won't be able to use the burning technique on an actual spill until it has been tested in a controlled experiment. Despite such concerns, the Canadian government is going ahead with a test burn off the coast of Newfoundland next year. Faced with a choice of test burning or the kind of shoreline contamination left in the wake of the Exxon Valdez disaster, Environment Canada opts for testing. Learning valuable lessons about rapid oil-spill cleanup is worth the relatively minor risks to the environment that test burning would pose

Laminar burning velocities of near-flammability-limit H2-air-steam mixtures

International Nuclear Information System (INIS)

Loesel Sitar, J.V.; Chan, C.K.; Torchia, F.; Guerrero, A.

1995-01-01

Laminar burning velocities of lean H 2 -air-steam mixtures near the flammability limit were measured by using the pressure-time history of an expanding flame kernel. Although flames in these mixtures are inherently unstable, this difficulty was avoided by using the early pressure rise of the burn. A comparison of results from that method with burning velocities determined from schlieren photographs of the expanding flame kernel gave good agreement. Despite the difficulties, it is believed that the pressure trace method gives results that are useful in modelling reactor accident scenarios. 8 refs., 4 figs

Small-scale in-situ burn tests to develop operational proficiencies

International Nuclear Information System (INIS)

McCarthy, M.W.

1996-01-01

A small-scale hands-on in-situ burning experiment was conducted to prepare members of a response community in the event of an actual full scale in-situ burn. Two different styles of fire booms were deployed in open water and exposed to multiple test tank burns. Residual burned crude oil was recovered and the booms decontaminated. The experiments showed that all the methods used to gauge the depth of oil contained in the booms created an element of doubt in their accuracy. The main lessons learned pertained to pre-combustion volume estimation, oil slick ignition, and residue recovery. It was concluded that in-situ burning was a potential technique in oil spill response, but some refinement is still needed to be done with the oil retention booms. The operational costs associated with the experiment were minimal, given the nature of the project. 1 tab

Benchmarks for multidimensional recovery after burn injury in young adults: the development, validation, and testing of the American Burn Association/Shriners Hospitals for Children young adult burn outcome questionnaire.

Science.gov (United States)

Ryan, Colleen M; Schneider, Jeffrey C; Kazis, Lewis E; Lee, Austin; Li, Nien-Chen; Hinson, Michelle; Bauk, Helena; Peck, Michael; Meyer, Walter J; Palmieri, Tina; Pidcock, Frank S; Reilly, Debra; Tompkins, Ronald G

2013-01-01

Although data exist on burn survival, there are little data on long-term burn recovery. Patient-centered health outcomes are useful in monitoring and predicting recovery and evaluating treatments. An outcome questionnaire for young adult burn survivors was developed and tested. This 5-year (2003-2008) prospective, controlled, multicenter study included burned and nonburned adults ages 19 to 30 years. The Young Adult Burn Outcome Questionnaires were completed at initial contact, 10 days, and 6 and 12 months. Factor analysis established construct validity. Reliability assessments used Cronbach α and test-retest. Recovery patterns were investigated using generalized linear models, with generalized estimating equations using mixed models and random effects. Burned (n = 153) and nonburned subjects (n = 112) completed 620 questionnaires (47 items). Time from injury to first questionnaire administration was 157 ± 36 days (mean ± SEM). Factor analysis included 15 factors: Physical Function, Fine Motor Function, Pain, Itch, Social Function Limited by Physical Function, Perceived Appearance, Social Function Limited by Appearance, Sexual Function, Emotion, Family Function, Family Concern, Satisfaction With Symptom Relief, Satisfaction With Role, Work Reintegration, and Religion. Cronbach α ranged from 0.72 to 0.92, with 11 scales >0.8. Test-retest reliability ranged from 0.29 to 0.94, suggesting changes in underlying health status after burns. Recovery curves in five domains, Itch, Perceived Appearance, Social Function Limited by Appearance, Family Concern, and Satisfaction with Symptom Relief, remained below the reference group at 24 months. The Young Adult Burn Outcome Questionnaire is a reliable and valid instrument for multidimensional functional outcomes assessment. Recovery in some domains was incomplete.

Effects of NOX Storage Component on Ammonia Formation in TWC for Passive SCR NOX Control in Lean Gasoline Engines

Energy Technology Data Exchange (ETDEWEB)

Prikhodko, Vitaly Y. [ORNL; Pihl, Josh A. [ORNL; Toops, Todd J. [ORNL; Parks, II, James E. [ORNL

2018-04-01

A prototype three-way catalyst (TWC) with NOX storage component was evaluated for ammonia (NH3) generation on a 2.0-liter BMW lean burn gasoline direct injection engine as a component in a passive ammonia selective catalytic reduction (SCR) system. The passive NH3 SCR system is a potential approach for controlling nitrogen oxides (NOX) emissions from lean burn gasoline engines. In this system, NH3 is generated over a close-coupled TWC during periodic slightly-rich engine operation and subsequently stored on an underfloor SCR catalyst. Upon switching to lean, NOX passes through the TWC and is reduced by the stored NH3 on the SCR catalyst. Adding a NOX storage component to a TWC provides two benefits in the context of a passive SCR system: (1) enabling longer lean operation by storing NOX upstream and preserving NH3 inventory on the downstream SCR catalyst; and (2) increasing the quantity and rate of NH3 production during rich operation. Since the fuel penalty associated with passive SCR NOX control depends on the fraction of time that the engine is running rich rather than lean, both benefits (longer lean times and shorter rich times achieved via improved NH3 production) will decrease the passive SCR fuel penalty. However, these benefits are primarily realized at low to moderate temperatures (300-500 °C), where the NOX storage component is able to store NOX, with little to no benefit at higher temperatures (>500 °C), where NOX storage is no longer effective. This study discusses engine parameters and control strategies affecting the NH3 generation over a TWC with NOX storage component.

Introduction to adoption of lean canvas in software test architecture design

Directory of Open Access Journals (Sweden)

Padmaraj Nidagundi

2017-01-01

Full Text Available The growth of the software dependent businesses, as well as the use of electronic devices in daily life, brings new challenges requiring the software to work error free all the time, to achieve this goal software needs to be sufficiently and effectively tested during various development phases. Most software development companies make great efforts in testing; it is even more difficult to reach the error-free software goal. Different software development methodologies (e.g. traditional waterfall, agile brought in a new dimension for both - development and testing - introducing new technologies and tools. In software test automation the test architecture design plays a key role in managing written test cases and effectively executing them. Having the more effective software test automation architecture design in test process saves resources, efforts and reduces the technical depth. This paper provides the new dimension and possibilities of using lean canvas in the design of the software test architecture.

The Role of Molecule Clustering by Hydrogen Bond in Hydrous Ethanol on Laminar Burning Velocity

Directory of Open Access Journals (Sweden)

I Made Suarta

2016-01-01

Full Text Available The role of hydrogen bond molecule clustering in laminar burning velocities was observed. The water in hydrous ethanol can change the interaction between water-ethanol molecules. A certain amount of water can become oxygenated which increases the burning velocity. The hydrogen bond interaction pattern of ethanol and water molecules was modeled. Based on the molecular model, azeotropic behavior emerges from ethanol-water hydrogen bond, which is at a 95.1%v composition. The interaction with water molecule causes the ethanol molecule to be clustered with centered oxygenated compound. So, it supplies extra oxygen and provides intermolecular empty spaces that are easily infiltrated by the air. In the azeotropic composition, the molecular bond chain is the shortest, so hypothetically the burning velocity is anticipated to increase. The laminar burning velocity of ethanol fuel was tested in a cylindrical explosion bomb in lean, stoichiometric, and rich mixtures. The experimental result showed that the maximum burning velocity occurred at hydrous ethanol of 95.5%v composition. This discrepancy is the result of the addition of energy from 7.7% free ethanol molecules that are not clustered. At the rich mixture, the burning velocity of this composition is higher than that of anhydrous ethanol.

Lean-team effectiveness through leader values and members’ informing

NARCIS (Netherlands)

van Dun, Desirée Hermina; Wilderom, Celeste P.M.

2016-01-01

Purpose Although empirical tests of effective lean-team leadership are scarce, leaders are often blamed when lean work-floor initiatives fail. In the present study, a lean-team leader’s work values are assumed to affect his or her team members’ behaviors and, through them, to attain team

Improving burn care and preventing burns by establishing a burn database in Ukraine.

Science.gov (United States)

Fuzaylov, Gennadiy; Murthy, Sushila; Dunaev, Alexander; Savchyn, Vasyl; Knittel, Justin; Zabolotina, Olga; Dylewski, Maggie L; Driscoll, Daniel N

2014-08-01

Burns are a challenge for trauma care and a contribution to the surgical burden. The former Soviet republic of Ukraine has a foundation for burn care; however data concerning burns in Ukraine has historically been scant. The objective of this paper was to compare a new burn database to identify problems and implement improvements in burn care and prevention in this country. Retrospective analyses of demographic and clinical data of burn patients including Tukey's post hoc test, analysis of variance, and chi square analyses, and Fisher's exact test were used. Data were compared to the American Burn Association (ABA) burn repository. This study included 1752 thermally injured patients treated in 20 hospitals including Specialized Burn Unit in Municipal Hospital #8 Lviv, Lviv province in Ukraine. Scald burns were the primary etiology of burns injuries (70%) and burns were more common among children less than five years of age (34%). Length of stay, mechanical ventilation use, infection rates, and morbidity increased with greater burn size. Mortality was significantly related to burn size, inhalation injury, age, and length of stay. Wound infections were associated with burn size and older age. Compared to ABA data, Ukrainian patients had double the length of stay and a higher rate of wound infections (16% vs. 2.4%). We created one of the first burn databases from a region of the former Soviet Union in an effort to bring attention to burn injury and improve burn care. Copyright © 2013 Elsevier Ltd and ISBI. All rights reserved.

Laminar burning velocities of near-flammability-limit H{sub 2}-air-steam mixtures

Energy Technology Data Exchange (ETDEWEB)

Loesel Sitar, J V; Chan, C K; Torchia, F; Guerrero, A

1996-12-31

Laminar burning velocities of lean H{sub 2}-air-steam mixtures near the flammability limit were measured by using the pressure-time history of an expanding flame kernel. Although flames in these mixtures are inherently unstable, this difficulty was avoided by using the early pressure rise of the burn. A comparison of results from that method with burning velocities determined from schlieren photographs of the expanding flame kernel gave good agreement. Despite the difficulties, it is believed that the pressure trace method gives results that are useful in modelling reactor accident scenarios. 8 refs., 4 figs.

Lean manufacturing measurement: the relationship between lean activities and lean metrics

Directory of Open Access Journals (Sweden)

Manotas Duque Diego Fernando

2007-10-01

Full Text Available Lean Manufacturing was developed by Toyota Motor company to address their specific needs in a restricted market in times of economic trouble. These concepts have been studied and proven to be transferrable and applicable to a wide variety of industries. This paper aims to integrate a set of metrics that have been proposed by different authors in such a way that they are consistent with the different stages and elements of Lean Manufacturing implementations. To achieve this, two frameworks for Lean implementations are presented and then the main factors for success are used as the basis to propose metrics that measure the advance in these factors. A tabular display of the impact of “Lean activities” on the metrics is presented, proposing that many a priori assumptions about the benefits on many different levels of improvement should be accurate. Finally, some ideas for future research and extension of the applications proposed on this paper are presented as closing points.

Comparative Analysis between Lean, Six Sigma and Lean Six Sigma Concepts

Directory of Open Access Journals (Sweden)

Alexandra Mirela Cristina MUNTEANU

2017-06-01

Full Text Available This paper analyzes the benefits of Lean Six Sigma in comparison with Lean and Six Sigma, traditional improvement methodologies. The introduction highlights the appearance of Lean Six Sigma, early 2000s, as well as the benefits brought by the integrated approach. The following parts of the study emphasize the main differences between methodologies and their commonalities based on their synergy. Finally the advantages of Lean Six Sigma versus Lean and Six Sigma are analyzed and systematized by author in order to reveal Lean Six Sigma’s benefits.

Healthcare Lean.

Science.gov (United States)

Long, John C

2003-01-01

Lean Thinking is an integrated approach to designing, doing and improving the work of people that have come together to produce and deliver goods, services and information. Healthcare Lean is based on the Toyota production system and applies concepts and techniques of Lean Thinking to hospitals and physician practices.

Lean versus Quick Response Manufacturing og andre koncepter - er Lean den eneste ene?

DEFF Research Database (Denmark)

Michelsen, Aage U

2005-01-01

Begrebet Lean har gennem de senere år vundet en enorm udbredelse. Antallet af publikationer om Lean har været eksplosivt stigende, og mange virksomheder har gennemført eller gennemfører Lean-projekter. Er Lean et nyt koncept? Er Lean den eneste løsning? Kan Lean kombineres med tankegange og princ...... løsning af en anden produktionsopgave. I fjerde afsnit skitseres kort relationerne mellem Lean og to andre begreber, Six Sigma og TPM, der begge har samme mål som Lean, men forskellige udgangspunkter og forskellige indfaldsvinkler....

Comparative Analysis between Lean, Six Sigma and Lean Six Sigma Concepts

OpenAIRE

Alexandra Mirela Cristina MUNTEANU

2017-01-01

This paper analyzes the benefits of Lean Six Sigma in comparison with Lean and Six Sigma, traditional improvement methodologies. The introduction highlights the appearance of Lean Six Sigma, early 2000s, as well as the benefits brought by the integrated approach. The following parts of the study emphasize the main differences between methodologies and their commonalities based on their synergy. Finally the advantages of Lean Six Sigma versus Lean and Six Sigma are analyzed and systematized by...

Experimental study of sodium droplet burning in free fall. Evaluation of preliminary test results

International Nuclear Information System (INIS)

Miyahara, Shinya; Ara, Kuniaki

1998-08-01

To study a sodium leak and combustion behavior phenomenologically and to construct the mechanistic evaluation method, an experimental series of a sodium droplet burning in free fall is under way. In this study, the accuracy of measurement technique used in the preliminary test was assessed and the modified technique was proposed for the next test series. Analytical study of the test results was also conducted to deduce dominant parameters and important measurement items which would play an important role in the droplet combustion behavior. The results and conclusions are as follows: (1) Assessment of measurement accuracy and modified technique proposed for the next test series. a) Control accuracy of sodium supply system using β-alumina solid electrolyte was sufficient for generation of objective size of single droplet. However, it is necessary to calibrate the correlation between the quantity of electric charge for sodium supply system and that of supplied sodium. b) Measurement accuracy of falling velocity using high-speed video was ±0.33 m/s at an upper part and ±0.48 m/s at a lower part of the measurement. To reduce the error, a high-speed stroboscopic method is recommended to measure the falling velocity of droplet. (2) Results of analytical study and deduced dominant parameters and important measurement items. a) The falling behavior of a burning droplet was described solving the equation of free falling motion for a rigid sphere. In the case of higher falling height, it is necessary to study the burning effects on the falling behavior. b) The mass burned of a falling droplet was calculated using the combustion model according to 'D 2 ' law during the full burning phase. It is necessary to study the dominant chemical reaction in the burning flame because the mass burned depends on the composition of the reaction products. c) The mass burned was calculated using surface oxidation model for preignition phase together with above model. However, it is

Negotiating Lean

DEFF Research Database (Denmark)

Rahbek Pedersen, Esben; Muniche, Mahad

2011-01-01

Purpose – The purpose of this paper is to analyse how negotiations between the constituencies affect the processes and outcomes of lean projects in Danish public sector organisations. Design/methodology/approach – The paper is based on a qualitative analysis of interviews with managers...... projects in the Danish public sector. It cannot be concluded that the findings can be generalised to reflect all types of lean projects across organisational and geographical settings. Originality/value – The paper adds value to the relatively scarce literature on lean management in the public sector...... and employees who have participated in lean projects in the Danish public sector. Negotiated order theory serves as the overarching theoretical framework for the analysis. Findings – The paper concludes that the processes and outcomes of lean depend not only on the technology itself, but also the negotiation...

Lean og arbejdsmiljø

DEFF Research Database (Denmark)

Jensen, Kenneth

Bogen tager udgangspunkt i en undersøgelse af 10 private og offentlige virksomheders erfaringer med lean. Undersøgelsen viser at der ikke findes entydige sammenhænge mellem lean og det psykosociale arbejdsmiljø. Bogen forholder sig til sammenhængen mellem lean og ledelse, lean og medarbejderens...... rolle, lean og lean og forandringsprocessen. Bogen kommer desuden med anbefalinger til hvorledes virksomheden kan gribe dialogen an for at opnå et godt lean forløb der inddrager hensynet til og effekterne af et godt psykosocialt arbejdsmiljø....

EDUCATION FOR LEAN & LEAN FOR EDUCATION: A LITERATURE REVIEW

Directory of Open Access Journals (Sweden)

Saveta Vukadinovic

2017-03-01

Full Text Available The purpose of this paper is to investigate and understand how tools and principles of Lean philosophy can be adopted to improve the effectiveness of engineering education by providing services beyond the competition and costs below the competition, and how engineering education can provide better prepared engineering professionals capable to work in dynamic Lean environments by developing multidisciplinary knowledge and skills. Paper will be based on analysis of relevant scientific and professional literature sources, including certain elements of description, classification, explanation and prediction. The authors will use detailed literature review to explain complex relationship and interdependence between Lean philosophy and engineering education and answer the question what benefits modern Lean enterprises may expect from properly educated and qualified engineers and how application of Lean tools and principles can improve the system of engineering education.

Bevezetés a lean menedzsmentbe – a lean stratégiai alapjai = Introduction to lean management – basic strategic elements of lean

OpenAIRE

Losonci, Dávid

2010-01-01

A lean menedzsment az értékteremtő folyamatok stratégiai és operatív szintjének meghatározó formálójává vált az elmúlt évtizedekben. Jelen tanulmány stratégiai nézőpontból tárgyalja a lean menedzsment teljes bevezetését. Részletes áttekintést ad a Womack és Jones (2003) által lefektetett lean alapelvekről. Az operatív teljesítményjavulásból származó vevői értékteremtés mellett foglalkozik a tulajdonosi értékteremtéssel, az MRP és a lean szinergikus összekapcsolásával, valamint a lean ideális ...

Tests of Flammability of Cotton Fabrics and Expected Skin Burns in Microgravity

Science.gov (United States)

Cavanagh, Jane M.; Torvi, David A.; Gabriel, Kamiel S.; Ruff, Gary A.

2004-01-01

During a shuttle launch and other portions of space flight, astronauts wear specialized flame resistant clothing. However during most of their missions on board the Space Shuttle or International Space Station, astronauts wear ordinary clothing, such as cotton shirts and pants. As the behaviour of flames is considerably different in microgravity than under earth s gravity, fabrics are expected to burn in a different fashion in microgravity than when tested on earth. There is interest in determining how this change in burning behaviour may affect times to second and third degree burn of human skin, and how the results of standard fabric flammability tests conducted under earth s gravity correlate with the expected fire behaviour of textiles in microgravity. A new experimental apparatus was developed to fit into the Spacecraft Fire Safety Facility (SFSF), which is used on NASA s KC-135 low gravity aircraft. The new apparatus was designed to be similar to the apparatus used in standard vertical flammability tests of fabrics. However, rather than using a laboratory burner, the apparatus uses a hot wire system to ignite 200 mm high by 80 mm wide fabric specimens. Fabric temperatures are measured using thermocouples and/or an infrared imaging system, while flame spread rates are measured using real time observations or video. Heat flux gauges are placed between 7 and 13 mm away from the fabric specimen, so that heat fluxes from the burning fabric to the skin can be estimated, along with predicted times required to produce skin burns.

Internal lean practitioner's challenges in lean principles ...

African Journals Online (AJOL)

The approach to this paper is to answer the questions such as “how does internal management commitment impact the Lean principles?”, “how does Supply Chain Management practices impact the lean principles?”, “can Supply Chain Management practices be embedded with internal management commitment?

LEAN LABORATORY APPROACHES FOR QUALITY ASSURANCE IN FOOD

Directory of Open Access Journals (Sweden)

Laxmana Naik

2011-09-01

Full Text Available A lean laboratory is one which is focused on testing products and materials to deliver results in the most efficient way in terms of cost or speed or both; primarily focused on improving measurable performance and reducing costs. The goal of a lean laboratory is to use less effort, less resources and less time to test incoming samples. Laboratories have a critical role to play in establishing and improving process capability and key performance indicator (KPI of the organization. There are inevitably many opinions as to what a lean lab actually is; here is one version fr om. Quality assurance laboratories are crucial to the success of organization and this effectiveness needs to be measurable and demonstrable. To facilitate this, a method of measuring a laboratory's progress towards complete deployment has been created by lean tools. These tools allow laboratories to conduct gap analysis and identify opportunities for improvement.

Results of laboratory tests on the potential for using in situ burning on seventeen crude oils

International Nuclear Information System (INIS)

McCourt, J.; Buist, I.; Buffington, S.

2000-01-01

The past five years at SL Ross (Ottawa) have been spent analysing seventeen crude oils to establish whether each oil could be cleaned up using an in situ burning technique in the event of a spill. The process involved a series of laboratory tests and controlled burns. The authors determined the emulsification characteristics, the limits to ignition imposed by evaporation and emulsion formation using a series of baseline burns, as well as the emulsion breaker burn test on emulsions that could not be ignited with gelled gas in the baseline burn test. They also determined the density, viscosity, and for some oils the interfacial tension, pour point, and flash point. The results obtained provided valuable information to be used in the case of a spill. They also indicated avenues to be followed in future research. 10 refs., 2 tabs

Lean i Norge : opplever norske bedrifter som er mer lean, større økning i kundetilfredshet enn de som er mindre lean?

OpenAIRE

Fagereng, Hanne Eline; Askevold, Elisabeth Cathrine

2010-01-01

Vi ønsker å måle i hvor stor grad norske bedrifter har implementert lean, og for å måle grad av lean har vi utviklet et rammeverk basert på lean teori. Hovedformålet med lean er å øke kundeverdi med minst mulig ressursbruk, anstrengelse, energi, utstyr, tid, plass, material og kapital (Womack, Roos and Jones 2007). Vi vil utforske om høyere grad av lean fører til mer tilfredse kunder enn de som har lavere grad av lean. Altså om hovedformålet med lean blir oppnådd hvis man implementerer lean i...

An experimental investigation of a lean-burn natural-gas pre-chamber spark ignition engine for cogeneration; Swiss Motor. Modification d'un moteur diesel pour le fonctionnement au gaz naturel en cogeneration. Fonctionnement avec prechambre de combustion

Energy Technology Data Exchange (ETDEWEB)

Roethlisberger, R.; Favrat, D.

2001-07-01

This thesis presented at the Department of Mechanical Engineering of the Swiss Federal Institute of Technology in Lausanne describes the conversion and testing of a commercial diesel engine for use as a lean-burn, natural gas, pre-chamber, spark ignition engine with a rated power of 150 kW, in combined heat and power (CHP) plants. The objective of the investigations - to evaluate the potential of reducing exhaust gas emissions - is discussed in detail with respect to NO{sub x} and CO emissions. The approach adopted includes both experimental work and numerical simulation. The report describes the testing facilities used. The results obtained with experimental spark-plug configurations based on simulation results are presented and the influence of various pre-chamber configuration variants are discussed. The results of the tests are presented and the significant reduction of NO{sub x}, CO and unburned-hydrocarbon (THC) emissions are discussed. The authors state that the engine, which achieves a fuel efficiency of more than 36.5%, fulfils the Swiss requirements on exhaust gas emissions. Also, ways of compensating for the slight loss in fuel-conversion efficiency in the pre-chamber configuration are discussed.

Simultaneous NOx and hydrocarbon emissions control for lean-burn engines using low-temperature solid oxide fuel cell at open circuit.

Science.gov (United States)

Huang, Ta-Jen; Hsu, Sheng-Hsiang; Wu, Chung-Ying

2012-02-21

The high fuel efficiency of lean-burn engines is associated with high temperature and excess oxygen during combustion and thus is associated with high-concentration NO(x) emission. This work reveals that very high concentration of NO(x) in the exhaust can be reduced and hydrocarbons (HCs) can be simultaneously oxidized using a low-temperature solid oxide fuel cell (SOFC). An SOFC unit is constructed with Ni-YSZ as the anode, YSZ as the electrolyte, and La(0.6)Sr(0.4)CoO(3) (LSC)-Ce(0.9)Gd(0.1)O(1.95) as the cathode, with or without adding vanadium to LSC. SOFC operation at 450 °C and open circuit can effectively treat NO(x) over the cathode at a very high concentration in the simulated exhaust. Higher NO(x) concentration up to 5000 ppm can result in a larger NO(x) to N(2) rate. Moreover, a higher oxygen concentration promotes NO conversion. Complete oxidation of HCs can be achieved by adding silver to the LSC current collecting layer. The SOFC-based emissions control system can treat NO(x) and HCs simultaneously, and can be operated without consuming the anode fuel (a reductant) at near the engine exhaust temperature to eliminate the need for reductant refilling and extra heating.

Lean information management

NARCIS (Netherlands)

Hammer, D.K.

1997-01-01

The concept of a Lean Enterprise has proven to be extremely valuable for making companies fit for today's competitive business environment. Lean Information Management denotes the type of information management that is appropriate for such all organization. According to the paradigm of a Lean

Lean production

OpenAIRE

Veselková, Jana

2011-01-01

The goal of this Bachelor's Thesis is to describe the general principles of lean production and afterwards apply these principles in a particular company. Due to the changing conditions on the world market is among companies growing concern about such innovative business systems. The theoretical part of this work deals with the general characteristics of lean production, including their history and focus on Toyota, as the originator of most lean systems. Mentioned are also the economic aspect...

EPA Lean Government Initiative: How to Replicate Lean Successes

Science.gov (United States)

This Lean Replication Primer describes how EPA Offices and Regions can identify and adapt successful practices from previous Lean projects to “replicate” their successes and generate further improvements.

Leading Lean: a Canadian healthcare leader's guide.

Science.gov (United States)

Fine, Benjamin A; Golden, Brian; Hannam, Rosemary; Morra, Dante

2009-01-01

Canadian healthcare organizations are increasingly asked to do more with less, and too often this has resulted in demands on staff to simply work harder and longer. Lean methodologies, originating from Japanese industrial organizations and most notably Toyota, offer an alternative - tried and tested approaches to working smarter. Lean, with its systematic approaches to reducing waste, has found its way to Canadian healthcare organizations with promising results. This article reports on a study of five Canadian healthcare providers that have recently implemented Lean. We offer stories of success but also identify potential obstacles and ways by which they may be surmounted to provide better value for our healthcare investments.

Analysis Of Lean Accounting JIT And Balance Scorecard In The Companys Lean Manufacturing

OpenAIRE

Irwan Sutirman Wahdiat

2015-01-01

This research purpose to analyze the concept of Lean Manufacturing which is influenced by the role of JIT. This research uses a theoretical approach. This study portrait thinking companies that have yet to implement lean manufacturing and after doing the concept of lean manufacturing. This study shows that the concept of lean manufacturing can make the company more efficient and effective. This paper shows some lean manufacturing dimensions of the researchers previous researchers. This study ...

Improving Healthcare through Lean Management: Experiences from the Danish healthcare system

DEFF Research Database (Denmark)

Edwards, Kasper; Nielsen, Anders Paarup

still is in its infancy and it is just a matter of letting sufficient time pass in order have a successful implementation of lean in all areas of healthcare. The second hypothesis states that a major barrier to lean management in healthcare simply is lacking understanding of the lean concepts leading......The ideas and principles from lean management are now widely being adopted within the healthcare sector. The analysis in this paper shows that organizations within healthcare most often only implement a limited set of tools and methods from the lean tool-box. Departing from a theoretical analysis...... of the well-known and universal lean management principles in the context of the healthcare this paper will attempt to formulate and test four hypotheses about possible barriers to the successful implementation of lean management in healthcare. The first hypothesis states that lean management in healthcare...

Mid-scale tests of in situ burning in a new wave tank at Prudhoe Bay, AK

International Nuclear Information System (INIS)

Buist, I.; McCourt, J.; Mullin, J.; Glover, N.; Hutton, C.; McHale, J.

1998-01-01

A series of mid-scale research burns with weathered Alaska North Slope crude, Milne Pt. crude and emulsion slicks were carried out in the fall of 1997 in Prudhoe Bay, Alaska. A suitable wave tank was developed for the in-situ burning tests. The objective was to determine the effects of oil type, emulsification, temperature and waves on in situ burning in Arctic open water conditions. More than 60 individual burns were conducted under various parameters including varying slick thickness, water content, wave energy, degree of weathering and oil type. Results showed that a spill of 60 per cent water emulsion of weathered Alaska North Slope crude was successfully burned in the highest waves tested, with an oil removal efficiency of 79 per cent, after treatment with emulsion breakers. A slick of 60 per cent water emulsion of weathered Milne Pt. crude was also successfully burned under the same conditions but without the addition of emulsion breakers. 10 refs., 1 tab., 13 figs

Predictors of muscle protein synthesis after severe pediatric burns.

Science.gov (United States)

Diaz, Eva C; Herndon, David N; Lee, Jinhyung; Porter, Craig; Cotter, Matthew; Suman, Oscar E; Sidossis, Labros S; Børsheim, Elisabet

2015-04-01

Following a major burn, skeletal muscle protein synthesis rate increases but is often insufficient to compensate for massively elevated muscle protein breakdown rates. Given the long-term nature of the pathophysiologic response to burn injury, we hypothesized that muscle protein synthesis rate would be chronically elevated in severely burned children. The objectives of this study were to characterize muscle protein synthesis rate of burned children over a period of 24 months after injury and to identify predictors that influence this response. A total of 87 children with 40% or greater total body surface area (TBSA) burned were included. Patients participated in stable isotope infusion studies at 1, 2, and approximately 4 weeks after burn and at 6, 12, and 24 months after injury to determine skeletal muscle protein fractional synthesis rate. Generalized estimating equations with log link normal distribution were applied to account for clustering of patients and control for patient characteristics. Patients (8 ± 6 years) had large (62, 51-72% TBSA) and deep (47% ± 21% TBSA third degree) burns. Muscle protein fractional synthesis rate was elevated throughout the first 12 months after burn compared with established values from healthy young adults. Muscle protein fractional synthesis rate was lower in boys, in children older than 3 years, and when burns were greater than 80% TBSA. Muscle protein synthesis is elevated for at least 1 year after injury, suggesting that greater muscle protein turnover is a component of the long-term pathophysiologic response to burn trauma. Muscle protein synthesis is highly affected by sex, age, and burn size in severely burned children. These findings may explain the divergence in net protein balance and lean body mass in different populations of burn patients. Prognostic study, level III.

Making it lean applying lean practices to the work of it

CERN Document Server

Williams, Howard

2013-01-01

Making IT Lean: Applying Lean Practices to the Work of IT presents Lean concepts and techniques for improving processes and eliminating waste in IT operations and IT Service Management, in a manner that is easy to understand. The authors provide a context for discussing several areas of application within this domain, allowing you to quickly gain insight into IT processes and Lean principles.The text reviews IT Service Management, with reference to the IT Infrastructure Library (ITIL®) as a framework for best practices-explaining how to use it to accommod

Lean Startup and Lean Canvas Using for Innovative Product Development

Directory of Open Access Journals (Sweden)

Alena Buchalcevová

2016-06-01

Full Text Available Recently, new approaches to product development have emerged that focus on idea generation techniques and customer itself. One of them is the Lean Startup method that is described in this article along with the Lean Canvas method. The main goal of the article is to demonstrate the application of both methods to an innovative product development focused on providing interactive trips for families with children. The development of the product during individual phases is described and application of the Lean Startup and Lean Canvas principles is demonstrated. Finally, benefits of both methods contributing to the product success are discussed. Similar case studies start emerging worldwide, however in the Czech context are quite rare.

Lean hydrous and anhydrous bioethanol combustion in spark ignition engine at idle

International Nuclear Information System (INIS)

Chuepeng, Sathaporn; Srisuwan, Sudecha; Tongroon, Manida

2016-01-01

Highlights: • Anhydrous ethanol burns fastest in uncalibrated engine at equal equivalence ratio. • The leaner hydrous ethanol combustion tends to elevate the COV in imep. • Hydrous ethanol consumption was 10% greater than anhydrous ethanol at ϕ = 0.67 limit. • Optimizing alternative fuel engine at idle for stability and emission is suggested. - Abstract: The applications of anhydrous bioethanol to substitute or replace gasoline fuel have shown to attain benefits in terms of engine thermal efficiency, power output and exhaust emissions from spark ignition engines. A hydrous bioethanol has also been gained more attention due to its energy and cost effectiveness. The main aim of this work is to minimize fuel quantity injected to the intake ports of a four-cylinder engine under idle condition. The engine running with hydrous ethanol undergoes within lean-burn condition as its combustion stability is analyzed using an engine indicating system. Coefficient of variation in indicated mean effective pressure is an indicator for combustion stability with hydrocarbon and carbon monoxide emission monitoring as a supplement. Anhydrous ethanol burns faster than hydrous ethanol and gasoline in the uncalibrated engine at the same fuel-to-air equivalence ratio under idle condition. The leaner hydrous ethanol combustion tends to elevate the coefficient of variation in indicated mean effective pressure. The experimental results have found that the engine consumes greater hydrous ethanol by 10% on mass basis compared with those of anhydrous ethanol at the lean limit of fuel-to-air equivalence ratio of 0.67. The results of exhaust gas analysis were compared with those predicted by chemical equilibrium analysis of the fuel-air combustion; the resemble trends were found. Calibrating the alternative fueled engine for fuel injection quantity should be accomplished at idle with combustion stability and emissions optimization.

Moving on - beyond lean thinking

OpenAIRE

Koskela, Lauri

2004-01-01

Lean Thinking is currently often positioned as the underlying theory of lean production among practitioners and academics, although its originators, Womack and Jones, seem not to have presented it as a theory. This paper endeavors to analyze whether Lean Thinking can be viewed as a theory of lean production. For this purpose, a critical assessment of Lean Thinking is carried out. Lean Thinking is argued to lack an adequate conceptualization of production, which has led to imprecise concepts, ...

lean-ISD.

Science.gov (United States)

Wallace, Guy W.

2001-01-01

Explains lean instructional systems design/development (ISD) as it relates to curriculum architecture design, based on Japan's lean production system. Discusses performance-based systems; ISD models; processes for organizational training and development; curriculum architecture to support job performance; and modular curriculum development. (LRW)

Lean Leadership - Organizational Buy - Ins

Directory of Open Access Journals (Sweden)

Dr. Revathi Iyer

2017-05-01

Full Text Available Great organizations have become leaders due to their leadership and sustainable initiatives. One such initiative is adoption of lean leadership to align core strategies with all functional areas of business. Leadership is likely to take place in a lean environment because improvements that happen are continual and can only be supported by leadership which understands this important aspect. The topic of lean leadership organizational buy ins speaks on how lean leadership could affect organizations that adopt lean and other quality tools. Purpose of the study This study has been undertaken to understand When leadership more of is likely to take place in lean . Leadership plays a very important role while adopting lean processes and how lean leadership can address the process problem. Application of leadership lenses to lean processes needs great foresight thought and creativity. It has been also observed that lean management and lean processes can happen only if leadership is able to effectively communicate the thought of continual improvement to bring in a lean organization and a future state of processes where everything of a firm process and procedure is continually improving and the best strategies to manage this change becomes a philosophy. Lean leadership is associated with such a change. This enables leadership vision to be clear as it paves the way for current state and is clear to everyone. It is this leadership vision which enables employees to think and act in a way that perpetrates continual improvement. Hence leadership buys ins for lean are very necessary. The purpose of the study is also to understand how leaders can not only use cost reduction but also reducing time-to-market improving service quality and reducing risk exposure by adopting lean methods . it has been also seen that there is overall productivity and efficiency in organizations holistically when leadership endorses lean methodology. Radnor Z. and Bucci G. 2007

Application of lean manufacturing techniques in the Emergency Department.

Science.gov (United States)

Dickson, Eric W; Singh, Sabi; Cheung, Dickson S; Wyatt, Christopher C; Nugent, Andrew S

2009-08-01

"Lean" is a set of principles and techniques that drive organizations to continually add value to the product they deliver by enhancing process steps that are necessary, relevant, and valuable while eliminating those that fail to add value. Lean has been used in manufacturing for decades and has been associated with enhanced product quality and overall corporate success. To evaluate whether the adoption of Lean principles by an Emergency Department (ED) improves the value of emergency care delivered. Beginning in December 2005, we implemented a variety of Lean techniques in an effort to enhance patient and staff satisfaction. The implementation followed a six-step process of Lean education, ED observation, patient flow analysis, process redesign, new process testing, and full implementation. Process redesign focused on generating improvement ideas from frontline workers across all departmental units. Value-based and operational outcome measures, including patient satisfaction, expense per patient, ED length of stay (LOS), and patient volume were compared for calendar year 2005 (pre-Lean) and periodically after 2006 (post-Lean). Patient visits increased by 9.23% in 2006. Despite this increase, LOS decreased slightly and patient satisfaction increased significantly without raising the inflation adjusted cost per patient. Lean improved the value of the care we delivered to our patients. Generating and instituting ideas from our frontline providers have been the key to the success of our Lean program. Although Lean represents a fundamental change in the way we think of delivering care, the specific process changes we employed tended to be simple, small procedure modifications specific to our unique people, process, and place. We, therefore, believe that institutions or departments aspiring to adopt Lean should focus on the core principles of Lean rather than on emulating specific process changes made at other institutions.

Multispectral imaging burn wound tissue classification system: a comparison of test accuracies between several common machine learning algorithms

Science.gov (United States)

Squiers, John J.; Li, Weizhi; King, Darlene R.; Mo, Weirong; Zhang, Xu; Lu, Yang; Sellke, Eric W.; Fan, Wensheng; DiMaio, J. Michael; Thatcher, Jeffrey E.

2016-03-01

The clinical judgment of expert burn surgeons is currently the standard on which diagnostic and therapeutic decisionmaking regarding burn injuries is based. Multispectral imaging (MSI) has the potential to increase the accuracy of burn depth assessment and the intraoperative identification of viable wound bed during surgical debridement of burn injuries. A highly accurate classification model must be developed using machine-learning techniques in order to translate MSI data into clinically-relevant information. An animal burn model was developed to build an MSI training database and to study the burn tissue classification ability of several models trained via common machine-learning algorithms. The algorithms tested, from least to most complex, were: K-nearest neighbors (KNN), decision tree (DT), linear discriminant analysis (LDA), weighted linear discriminant analysis (W-LDA), quadratic discriminant analysis (QDA), ensemble linear discriminant analysis (EN-LDA), ensemble K-nearest neighbors (EN-KNN), and ensemble decision tree (EN-DT). After the ground-truth database of six tissue types (healthy skin, wound bed, blood, hyperemia, partial injury, full injury) was generated by histopathological analysis, we used 10-fold cross validation to compare the algorithms' performances based on their accuracies in classifying data against the ground truth, and each algorithm was tested 100 times. The mean test accuracy of the algorithms were KNN 68.3%, DT 61.5%, LDA 70.5%, W-LDA 68.1%, QDA 68.9%, EN-LDA 56.8%, EN-KNN 49.7%, and EN-DT 36.5%. LDA had the highest test accuracy, reflecting the bias-variance tradeoff over the range of complexities inherent to the algorithms tested. Several algorithms were able to match the current standard in burn tissue classification, the clinical judgment of expert burn surgeons. These results will guide further development of an MSI burn tissue classification system. Given that there are few surgeons and facilities specializing in burn care

Lean start-up

DEFF Research Database (Denmark)

Rasmussen, Erik Stavnsager; Tanev, Stoyan

2016-01-01

The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The ma...... and the final business model. In other words: The start-up must first nail the problem together with the customers, then develop the solution and test, and then in the end scale it to a full-grown business model.......The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The main...

Lean programm as a method of managing lean changes in the company

Directory of Open Access Journals (Sweden)

Suetina Tatiana Aleksandrovna

2012-12-01

Full Text Available This article is about methods and ways of providing changes on enterprices which introduce instruments of lean production. The main accent is how to use metodology of the project management by providing lean-changes. Lean program is proposed as a program of strategic developement of enterprices.

Implementation of lean thinking: one health system's journey.

Science.gov (United States)

Kim, Christopher S; Spahlinger, David A; Kin, Jeanne M; Coffey, Richard J; Billi, John E

2009-08-01

Lean Thinking is a management philosophy derived from the manufacturing industry, where Toyota has long been the gold standard. Health care organizations have started to apply this approach to patient care. After initial experimentation, the University of Michigan Health System (UMHS) has adopted Lean Thinking as its uniform approach to quality improvement and is striving to become a complete Lean organization. In 2005, the senior leadership selected an initial set of projects in areas that traced the patient's journey across different care settings within our health system. Four of the projects were as follows: orthopedic surgery clinic scheduling, radiation oncology therapy, peripherally inserted central catheter (PICC) services, and coordination of care to the outpatient setting. Lean Thinking encourages service providers to focus on value as defined by the customer and the relentless elimination of waste that impedes the flow of value. A series of learning projects were conducted to test whether Lean methods would work at UMHS. The following factors were found to be key to LEAN PROJECT SUCCESS: expert guidance for initial efforts, leadership in the form of clinical champions and senior management support of the improvement work, frontline worker engagement in mapping out "current state" processes, identifying waste and designing an improved "future state," using metrics to develop and track interventions, and defining realistic project scope. As UMHS's experience applying Lean Thinking to our patient care processes has grown, so have support, enthusiasm, and expertise within the organization. UMHS's Lean Thinking system, now known as the Michigan Quality System, has emerged as the core improvement strategy.

A new lean change methodology for small & medium sized enterprises

OpenAIRE

April, Joris; Powell, Daryl; Bart, Schanssema

2010-01-01

SMEs find it difficult to implement productivity improvement tools, particularly those associated with Lean Manufacturing. Larger companies have more success due to greater access to resources. To provide the SMEs with a way to implement Lean sustainably, the European project ERIP develops a new lean change methodology for SMEs. In this paper the methodology is explained and three test cases show the strength of the methodology. The method is a sequence of achieving management and company sup...

Implementation of lean leadership

Directory of Open Access Journals (Sweden)

Trenkner Małgorzata

2016-12-01

Full Text Available The Toyota case proves that lean leadership is of critical importance for the successful implementation and permanent functioning of Lean Production System. There is no ready formula for developing Toyota style lean leadership. However, one may gain inspiration from its experience.

46 CFR 126.160 - Tests and inspections during repairs or alterations, or during riveting, welding, burning, or...

Science.gov (United States)

2010-10-01

... during riveting, welding, burning, or other hot work. 126.160 Section 126.160 Shipping COAST GUARD... § 126.160 Tests and inspections during repairs or alterations, or during riveting, welding, burning, or... riveting, welding, burning, or other hot work may commence. (c) Each examination must be conducted as...

Assessment of Substances Abuse in Burn Patients by Using Drug Abuse Screening Test

Directory of Open Access Journals (Sweden)

Kobra Gaseminegad

2012-04-01

Full Text Available There has been an increase in the frequency of substance abuse among hospitalized burn injury patients. However, few studies have investigated substance abuse among burn patients. This study was aimed to identify the incidence of substance abuse in burn injury patients using the "Drug Abuse Screening Test" (DAST-20. We determined the validity of DAST-20 in spring 2010. Subsequently, this descriptive study was performed on 203 burn injury patients who fit the study's inclusion criteria. We chose a score of 6 as the cutoff and thus achieved a sensitivity of 89% and a specificity of 85% for the DAST-20. During the study, we gathered demographic data, burn features and DAST-20 results for all patients. Patients with scores of 6 or more were considered to be substances abusers. A statistical analysis was conducted using SPSS v16 software. According to the DAST-20 results, 33% of the patients were in the user group. The mean score of DAST-20 was significantly higher among users than it was among nonusers (P<0.05. The level of substance abuse was severe in 77% of users. No significant differences were found among the substances, with the exception of alcohol. Substance abuse is an important risk factor for burn patients. In addition, this study showed that DAST-20 is a valid screening measure for studies on burn patients.

In-situ burning of Orimulsion : small scale burns

International Nuclear Information System (INIS)

Fingas, M.F.

2002-01-01

This study examined the feasibility of burning Orimulsion. In-situ burning has always been a viable method for cleaning oil spills on water because it can effectively reduce the amount of spilled oil and eliminate the need to collect, store, transport and dispose of recovered oil. Orimulsion, however, behaves very differently from conventional oil when it is spilled because of its composition of 70 per cent bitumen in 30 per cent water. In-situ burning of this surfactant-stablized oil-in-water emulsion has never been seriously considered because of the perception that Orimulsion could not be ignited, and if it could, ignition would not be sustained. In this study, burn tests were conducted on 3 scales in a Cleveland Open Cup apparatus of 5 cm, 10 cm and 50 cm diameters. Larger scale burns were conducted in specially built pans. All tests were conducted on salt water which caused the bitumen to separate from the water. The objective was to determine if sufficient vapours could be generated to ignite the Orimulsion. The study also measured if a sustained flame would result in successful combustion. Both objectives were successfully accomplished. Diesel fuel was used to ignite the Orimulsion in the specially designed pan for large scale combustion. Quantitative removal of Orimulsion was achieved in all cases, but in some burns it was necessary to re-ignite the Orimulsion. It was noted that when Orimulsion burns, some trapped water droplets in the bitumen explode with enough force to extinguish a small flame. This did not occur on large-scale burns. It was concluded that the potential for successful in-situ burning increases with size. It was determined that approximately 1 mm in thickness of diesel fuel is needed to ignite a burn. 5 refs., 3 tabs., 4 figs

Lean leadership: an ethnographic study.

Science.gov (United States)

Aij, Kjeld Harald; Visse, Merel; Widdershoven, Guy A M

2015-01-01

The purpose of this study is to provide a critical analysis of contemporary Lean leadership in the context of a healthcare practice. The Lean leadership model supports professionals with a leading role in implementing Lean. This article presents a case study focusing specifically on leadership behaviours and issues that were experienced, observed and reported in a Dutch university medical centre. This ethnographic case study provides auto-ethnographic accounts based on experiences, participant observation, interviews and document analysis. Characteristics of Lean leadership were identified to establish an understanding of how to achieve successful Lean transformation. This study emphasizes the importance for Lean leaders to go to the gemba, to see the situation for one's own self, empower health-care employees and be modest. All of these are critical attributes in defining the Lean leadership mindset. In this case study, Lean leadership is specifically related to healthcare, but certain common leadership characteristics are relevant across all fields. This article shows the value of an auto-ethnographic view on management learning for the analysis of Lean leadership. The knowledge acquired through this research is based on the first author's experiences in fulfilling his role as a health-care leader. This may help the reader examining his/her own role and reflecting on what matters most in the field of Lean leadership.

In-situ burning of heavy oils and Orimulsion : mid-scale burns

International Nuclear Information System (INIS)

Fingas, M.F.; Fieldhouse, B.; Brown, C.E.; Gamble, L.

2004-01-01

In-situ burning is considered to be a viable means to clean oil spills on water. In-situ burning, when performed under the right conditions, can reduce the volume of spilled oil and eliminate the need to collect, store, transport and dispose of the recovered oil. This paper presented the results of bench-scale in-situ burning tests in which Bunker C, Orimulsion and weathered bitumen were burned outdoors during the winter in burn pans of approximately 1 square metre. Each test was conducted on salt water which caused the separation of the bitumen from the water in the Orimulsion. Small amounts of diesel fuel was used to ignite the heavy oils. Quantitative removal of the fuels was achieved in all cases, but re-ignition was required for the Orimulsion. Maximum efficiency was in the order of 70 per cent. The residue was mostly asphaltenes and resins which cooled to a solid, glass like material that could be readily removed. The study showed that the type of oil burned influences the behaviour of the burns. Bunker C burned quite well and Orimulsion burned efficiently, but re-ignition was necessary. It was concluded that there is potential for burning heavy oils of several types in-situ. 6 refs., 7 tabs., 18 figs

The impact of Lean bundles on hospital performance: does size matter?

Science.gov (United States)

Al-Hyari, Khalil; Abu Hammour, Sewar; Abu Zaid, Mohammad Khair Saleem; Haffar, Mohamed

2016-10-10

Purpose The purpose of this paper is to study the effect of the implementation of Lean bundles on hospital performance in private hospitals in Jordan and evaluate how much the size of organization can affect the relationship between Lean bundles implementation and hospital performance. Design/methodology/approach The research is considered as quantitative method (descriptive and hypothesis testing). Three statistical techniques were adopted to analyse the data. Structural equation modeling techniques and multi-group analysis were used to examine the research's hypothesis, and to perform the required statistical analysis of the data from the survey. Reliability analysis and confirmatory factor analysis were used to test the construct validity, reliability and measurement loadings that were performed. Findings Lean bundles have been identified as an effective approach that can dramatically improve the organizational performance of private hospitals in Jordan. Main Lean bundles - just in time, human resource management, and total quality management are applicable to large, small and medium hospitals without significant differences in advantages that depend on size. Originality/value According to the researchers' best knowledge, this is the first research that studies the impact of Lean bundles implementation in healthcare sector in Jordan. This research also makes a significant contribution for decision makers in healthcare to increase their awareness of Lean bundles.

Ares Launch Vehicles Lean Practices Case Study

Science.gov (United States)

Doreswamy, Rajiv; Self, Timothy A.

2007-01-01

The Ares launch vehicles team, managed by the Ares Projects Office (APO) at NASA Marshall Space Flight Center, has completed the Ares I Crew Launch Vehicle System Requirements Review and System Definition Review and early design work for the Ares V Cargo Launch Vehicle. This paper provides examples of how Lean Manufacturing, Kaizen events, and Six Sigma practices are helping APO deliver a new space transportation capability on time and within budget, while still meeting stringent technical requirements. For example, Lean philosophies have been applied to numerous process definition efforts and existing process improvement activities, including the Ares I-X test flight Certificate of Flight Readiness (CoFR) process, risk management process, and review board organization and processes. Ares executives learned Lean practices firsthand, making the team "smart buyers" during proposal reviews and instilling the team with a sense of what is meant by "value-added" activities. Since the goal of the APO is to field launch vehicles at a reasonable cost and on an ambitious schedule, adopting Lean philosophies and practices will be crucial to the Ares Project's long-term SUCCESS.

LEAN and energy efficiency; Lean og energieffektivisering

Energy Technology Data Exchange (ETDEWEB)

Jespersen, Per T; Vesterager Christensen, D; Andersen, Hans [Teknologisk Institut, Energi og Klima, Taastrup (Denmark); Dam Wied, M; Dam, M [NRGi Raadgivning, Aarhus (Denmark); Thorndahl, M [Horsens Kommune, Horsens (Denmark); Weldingh, P [Lokal Energi, Viby J. (Denmark); Maagoee, P; Kristensen, Kenneth T [Viegand og Maagoee, Copenhagen (Denmark); Kirketerp Friis, A [Novozymes, Bagsvaerd (Denmark)

2010-03-15

By means of theoretical reports and three specific cases, the project showed how Lean principles can improve energy consulting efficiency, thus making it easier for end-users and energy consultants to record and document energy savings achieved. The three cases documented various types of extra benefits of integrating energy efficiency improvement in Lean processes. As a result of process optimisation, one manufacturing company successfully reduced both staffing and energy consumption, thus making production in Denmark competitive with out-sourced production in Asia. (LN)

LEAN dig ikke tilbage

DEFF Research Database (Denmark)

Weirsøe, Mathilde

2011-01-01

Fit, slankere, hurtigst. Lean-konceptet ruller ind over de offentlige institutioner, hvor det skal trimme og effektivisere arbejdsprocesser. Men hvor er den maksimale grænse for effektivitet? Er der et ’tipping point’, hvor Lean ikke længere motiverer, men snarere udmatter......Fit, slankere, hurtigst. Lean-konceptet ruller ind over de offentlige institutioner, hvor det skal trimme og effektivisere arbejdsprocesser. Men hvor er den maksimale grænse for effektivitet? Er der et ’tipping point’, hvor Lean ikke længere motiverer, men snarere udmatter...

Orchestrating Lean Implementation

DEFF Research Database (Denmark)

Riis, Jens Ove; Mikkelsen, Hans; Andersen, Jesper Rank

2008-01-01

The notion of Lean Manufacturing is not merely confined to a set of well defined techniques, but represents a broad approach to managing a company. Working with lean entails many aspects, such as production planning and control, production engineering, product development, supply chain......, and organizational issues. To become effective, many functional areas and departments must be involved. At the same time companies are embedded in a dynamic environment. The aim of the paper is to propose a comprehensive approach to better implementation of lean initiatives, based on two empirical studies. The paper...... will discuss how a concerted effort can be staged taking into account the interdependencies among individual improvement initiatives. The notion of orchestration will be introduced, and several means for orchestration will be presented. Critical behavioral issues for lean implementation will be discussed....

Effect of pressure on the lean limit flames of H2-CH4-air mixture in tubes

KAUST Repository

Zhou, Zhen; Shoshin, Yuriy; Hernandez Perez, Francisco; van Oijen, Jeroen A.; de Goey, Laurentius P.H.

2017-01-01

The lean limit flames of H2-CH4-air mixtures stabilized inside tubes in a downward flow are experimentally and numerically investigated at elevated pressures ranging from 2 to 5 bar. For the shapes of lean limit flames, a change from ball-like flame to cap-like flame is experimentally observed with the increase of pressure. This experimentally observed phenomenon is qualitatively predicted by numerical simulations. The structure of ball-like and cap-like lean limit flames at all tested pressures is analysed in detail based on the numerical predictions. The results show that the lean limit flames are located inside a recirculation zone at all tested pressures. For the leading edges of the lean limit flames at all tested pressures, the fuel transport is controlled by both convection and diffusion. For the trailing edge of the ball-like lean limit flame at 2 bar, the fuel transport is dominated by diffusion. However, with increasing pressure, the transport contribution caused by convection in the trailing edges of the lean limit flames increases. Finally, the influence of transport and chemistry on the predicted ultra lean flames and lean flammability limit is analysed at elevated pressures.

Effect of pressure on the lean limit flames of H2-CH4-air mixture in tubes

KAUST Repository

Zhou, Zhen

2017-05-25

The lean limit flames of H2-CH4-air mixtures stabilized inside tubes in a downward flow are experimentally and numerically investigated at elevated pressures ranging from 2 to 5 bar. For the shapes of lean limit flames, a change from ball-like flame to cap-like flame is experimentally observed with the increase of pressure. This experimentally observed phenomenon is qualitatively predicted by numerical simulations. The structure of ball-like and cap-like lean limit flames at all tested pressures is analysed in detail based on the numerical predictions. The results show that the lean limit flames are located inside a recirculation zone at all tested pressures. For the leading edges of the lean limit flames at all tested pressures, the fuel transport is controlled by both convection and diffusion. For the trailing edge of the ball-like lean limit flame at 2 bar, the fuel transport is dominated by diffusion. However, with increasing pressure, the transport contribution caused by convection in the trailing edges of the lean limit flames increases. Finally, the influence of transport and chemistry on the predicted ultra lean flames and lean flammability limit is analysed at elevated pressures.

Cultural Aspects when Implementing Lean Production and Lean Product Development – Experiences from a Swedish Perspective

Directory of Open Access Journals (Sweden)

Promporn Wangwacharakul

2014-07-01

Full Text Available Lean principles and methods, originating in a Japanese cultural context, have spread to a large number of companies throughout the world. The aim of this case study research is to identify and compare national cultural aspects that influence Lean Production and Lean Product Development implementation in Swedish companies. Data were collected through questionnaires, interviews and an industrial workshop with Swedish Lean practitioners. The study shows that some sub-areas in Lean, such as value definition, control systems, leadership, team development, knowledge management, and strategies, are highly dependent on contextual factors related to human, cultural and organizational aspects. These are related to the national culture and should be considered to a higher extent for successful sustainable implementation of Lean in different cultural contexts. As for implementing Lean in Sweden, national cultural characteristics, such as individualism, autonomy and supportive management style fit well with Lean thinking.

The effectiveness of lean manufacturing audits in measuring operational performance improvements

Directory of Open Access Journals (Sweden)

Taggart, P.

2013-08-01

Full Text Available The hypothesis that lean manufacturing audits are an effective way to measure improvements in operational performance was tested using 64 manufacturing sites owned by a FTSE 100 company. Commonly-used lean characteristics were evaluated: policy deployment, standardised work, visual management and housekeeping, quick changeover techniques, total productive maintenance, continuous improvement (kaizen, error proofing, cultural awareness, material control, and levelling (heijunka. Operational performance was assessed employing commonly-used operational performance measures: on-time-delivery, inventory turns, and direct labour utilisation. The findings are that lean manufacturing audits are effective in measuring improvements in operational performance provided that the audit scope and the lean characteristics are aligned up front.

Diccionario Lean Manufacturing

OpenAIRE

Muñoz Ellner, Sarah María

2016-01-01

El Diccionario Bilingüe de Lean Manufacturing pretende ser un instrumento de apoyo a todo aquel que tenga la responsabilidad de planear, ejecutar o simplemente algún interés con las actividades de Lean Manufacturing, aportando así también conceptos claros tanto en castellano como en inglés, con el fin de entender de forma integral el alcance mismo que puede llegar a tener dicha filosofía, al igual que se proporcionara una serie de siglas y herramientas para la implementación del Lean Manufact...

Lean management beyond manufacturing a holistic approach

CERN Document Server

Bhasin, Sanjay

2015-01-01

Exploring Lean manufacturing in a holistic manner, this book helps organizations to implement Lean principles successfully by offering theoretical, empirical and practical knowledge. It empirically demonstrates how a successful Lean initiative can improve organizational efficiency, and incorporates valuable primary research to substantiate findings. It argues that Lean principles need to be applied throughout the value chain in order to be successful , and suggests that these tools need to be aligned with culture and change management. Chapters examine issues including Lean cultures, impediments to Lean, Lean and performance measurement, and the impact of Lean. Viewing Lean as a never-ending journey, this book provides a valuable resource to practising Lean managers, and specialist researchers and students, and also offers an important reference for organizations embarking on their Lean voyage.

Lean approach in knowledge work

Directory of Open Access Journals (Sweden)

Hanna Kropsu-Vehkapera

2018-05-01

Full Text Available Purpose: Knowledge work productivity is a key area of improvement for many organisations. Lean approach is a sustainable way to achieve operational excellence and can be applied in many areas. The purpose of this novel study is to examine the potential of using lean approach for improving knowledge work practices. Design/methodology/approach: A systematic literature review has been carried out to study how lean approach is realised in knowledge work. The research is conceptual in nature and draws upon earlier research findings. Findings: This study shows that lean studies’ in knowledge work is an emerging research area. This study documents the methods and practices implemented in knowledge work to date, and presents a knowledge work continuum, which is an essential framework for effective lean approach deployment and to frame future research focus in knowledge work productivity. Research limitations/implications: This study structures the concept of knowledge work and outlines a concrete concept derived from earlier literature. The study summarises the literature on lean in knowledge work and highlights, which methods are used. More research is needed to understand how lean can be implemented in complex knowledge work environment and not only on the repetitive knowledge work. The limitations of this research are due to the limited availability of previous research. Practical implications: To analyse the nature of knowledge work, we implicate the areas where lean methods especially apply to improving knowledge work productivity. When applying lean in knowledge work context the focus should be using the people better and improving information flow. Originality/value: This study focuses on adapting lean methods into a knowledge work context and summarises earlier research done in this field. The study discusses the potential to improve knowledge work productivity by implementing lean methods and presents a unique knowledge work continuum to

Lean and Information Technology Toolkit

Science.gov (United States)

The Lean and Information Technology Toolkit is a how-to guide which provides resources to environmental agencies to help them use Lean Startup, Lean process improvement, and Agile tools to streamline and automate processes.

Cull sow knife-separable lean content evaluation at harvest and lean mass content prediction equation development.

Science.gov (United States)

Abell, Caitlyn E; Stalder, Kenneth J; Hendricks, Haven B; Fitzgerald, Robert F

2012-07-01

The objectives of this study were to develop a prediction equation for carcass knife-separable lean within and across USDA cull sow market weight classes (MWC) and to determine carcass and individual primal cut knife separable lean content from cull sows. There were significant percent lean and fat differences in the primal cuts across USDA MWC. The two lighter USDA MWC had a greater percent carcass lean and lower percent fat compared to the two heavier MWC. In general, hot carcass weight explained the majority of carcass lean variation. Additionally, backfat was a significant variation source when predicting cull sow carcass lean. The findings support using a single lean prediction equation across MWC to assist processors when making cull sow purchasing decisions and determine the mix of animals from various USDA MWC that will meet their needs when making pork products with defined lean:fat content. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Application of Lean Thinking Principles and Kaizen Practices for the Successful Development and Implementation of the Ares I-X Flight Test Rocket and Mission

Science.gov (United States)

Askins, B. R.; Davis, S. R.; Heitzman, K. S.; Olsen, R. A.

2011-01-01

On October 28, 2009 the Ares I-X flight test rocket launched from Kennedy Space Center and flew its suborbital trajectory as designed. The mission was successfully completed as data from the test, and associated development activities were analyzed, transferred to stakeholders, and well documented. A positive lesson learned from Ares I-X was that the application of lean thinking principles and kaizen practices was very effective in streamlining development activities. Ares I-X, like other historical rocket development projects, was hampered by technical, cost, and schedule challenges and if not addressed boldly could have resulted in cancellation of the test. The mission management team conducted nine major meetings, referred to as lean events, across its elements to assess plans, procedures, processes, requirements, controls, culture, organization, use of resources, and anything that could be changed to optimize schedule or reduce risk. The preeminent aspect of the lean events was the focus on value added activities and the removal or at least reduction in non-value added activities. Trained Lean Six Sigma facilitators assisted the Ares I-X developers in conducting the lean events. They indirectly helped formulate the mission s own unique methodology for assessing schedule. A core team was selected to lead the events and report to the mission manager. Each activity leveraged specialized participants to analyze the subject matter and its related processes and then recommended alternatives and solutions. Stakeholders were the event champions. They empowered and encouraged the team to succeed. The keys to success were thorough preparation, honest dialog, small groups, adherence to the Ares I-X ground rules, and accountability through disciplined reporting and tracking of actions. This lean event formula was game-changing as demonstrated by Ares I-X. It is highly recommended as a management tool to help develop other complex systems efficiently. The key benefits for

Lean Production : Werkzeuge zur Realisierung

OpenAIRE

Binner, Hartmut F.

2008-01-01

INHALT: l. Einleitung und Standortbestimmung 2. Japanische Wertvorstellungen 3. Inhalte der Lean Production 4. Fertigungssegmentierung 5. Informationsmanagement mit CIM- und Logistik-Komponenten 6. Logistikgerechte Strukturen der Lean Production 7. Realisierung der Lean Production 8. Zusammenfassung

Measurement of volatiles, semi-volatiles and heavy metals in an oil burn test

International Nuclear Information System (INIS)

Li, K.; Caron, T.; Landriault, M.; Pare, J.R.J.; Fingas, M.

1992-01-01

Tests involving meso-scale burning of Louisiana crude oil were conducted, and during each burn, extensive samples were taken from the oil, residue, and the smoke plume. The detailed analytical work employed to obtain and analyze the burn samples is outlined and discussed. The analytical parameters included volatiles and semi-volatiles of environmental interests as well as heavy metals typically contained in the starting crude oil. Because the smoke plume did not always impinge on the samplers, the ground samplers did not collect sufficient samples for a definitive analysis. Crude/residue analyses showed the burn resulted in a significant reduction of polycyclic aromatic hydrocarbons (PAH) in the original oil. Most of the reduction was thought to be simply evaporation or destruction from combustion. The residue did not have the degree of enrichment of the higher molecular weight PAHs as was the case in bench-scale burn experiments. Volatile organic compound and dioxin/furan measurements likewise did not show high levels of contamination from the burn itself. Most of the elevated levels of contaminants could probably be due to evaporation of the oil itself. Insufficient sampling was conducted to investigate the background levels from the weathering process. A novel means of sampling using a small remote controlled helicopter was attempted and sufficiently interesting results were obtained to indicate the potential of this passive sampling device for future work. 5 refs., 4 figs

Researching Lean: Methodological Implications of Loose Definitions

Directory of Open Access Journals (Sweden)

Mikael Brännmark

2012-12-01

Full Text Available Recently, Lean Production (Lean has become a prevailing management concept in Sweden. However, previous research seems to show that the Lean concept and the impact of Lean vary considerably between organizations. This paper illustrates some key methodological issues that need to be considered when researching loosely defined management concepts such as Lean. The paper is based on a review of the literature and five comparative Swedish cases studies. Our study indicates that Lean has changed over time and that operationalization and interpretations of the concept vary considerably. This study concludes that future Lean studies should include a thorough assessment of the Lean interventions, study settings, and in particular non-Lean factors mediating the outcomes of Lean-inspired change programs.

Lean Application to Manufacturing Ramp-Up

DEFF Research Database (Denmark)

Christensen, Irene; Rymaszewska, Anna

2016-01-01

. Abstracting from the extant literature, the authors considered the competitiveness of manufacturing companies from two principal perspectives: the leanness of the ramp-up process and the new-value creation of quality managers. While much of the literature fails to acknowledge that the roots of lean actually......This article provides a theoretical overview of the concepts of lean and manufacturing ramp-up in an attempt to conceptualize the strategic areas in which lean philosophy and principles can be applied for continuous improvements. The application of lean principles during the final stage of a new...... product development process, that is, the ramp-up process, is a critical, early enabler of lean manufacturing. The manufacturing strategy literature conceptualizes a state of “leanness in operations,” which can consolidate both the concepts of lean and manufacturing ramp-up, providing a dual perspective...

LEAN thinking in Finnish healthcare.

Science.gov (United States)

Jorma, Tapani; Tiirinki, Hanna; Bloigu, Risto; Turkki, Leena

2016-01-01

Purpose - The purpose of this study is to evaluate how LEAN thinking is used as a management and development tool in the Finnish public healthcare system and what kind of outcomes have been achieved or expected by using it. The main focus is in managing and developing patient and treatment processes. Design/methodology/approach - A mixed-method approach incorporating the Webropol survey was used. Findings - LEAN is quite a new concept in Finnish public healthcare. It is mainly used as a development tool to seek financial savings and to improve the efficiency of patient processes, but has not yet been deeply implemented. However, the experiences from LEAN initiatives have been positive, and the methodology is already quite well-known. It can be concluded that, because of positive experiences from LEAN, the environment in Finnish healthcare is ready for the deeper implementation of LEAN. Originality/value - This paper evaluates the usage of LEAN thinking for the first time in the public healthcare system of Finland as a development tool and a management system. It highlights the implementation and achieved results of LEAN thinking when used in the healthcare environment. It also highlights the expectations for LEAN thinking in Finnish public healthcare.

Readiness factors for lean implementation in healthcare settings--a literature review.

Science.gov (United States)

Al-Balushi, S; Sohal, A S; Singh, P J; Al Hajri, A; Al Farsi, Y M; Al Abri, R

2014-01-01

The purpose of this paper is to determine the readiness factors that are critical to the application and success of lean operating principles in healthcare organizations through a review of relevant literature. A comprehensive review of literature focussing on lean and lean healthcare was conducted. Leadership, organizational culture, communication, training, measurement, and reward systems are all commonly attributed readiness factors throughout general change management and lean literature. However, directly related to the successful implementation of lean in healthcare is that a setting is able to authorize a decentralized management style and undertake an end-to-end process view. These can be particularly difficult initiatives for complex organizations such as healthcare settings. The readiness factors identified are based on a review of the published literature. The external validity of the findings could be enhanced if tested using an empirical study. The readiness factors identified will enable healthcare practitioners to be better prepared as they begin their lean journeys. Sustainability of the lean initiative will be at stake if these readiness factors are not addressed. To the best of the knowledge, this is the first paper that provides a consolidated list of key lean readiness factors that can guide practice, as well as future theory and empirical research.

Lean Design and Management for Manufactoring

OpenAIRE

NIU, Zhanwen

2009-01-01

Most enterprises inducting lean production were confined by the innate limitations of existing production systems, which make it difficult to fulfill lean production comprehensively. To solve this problem, the theory of lean design and management for the manufacturing enterprise lifecycle was proposed. First, the necessities of lean design were analyzed and its theoretical system was established; second, the principles, process, methods and tools for lean design was introduced. Techniques and...

Drive for leanness and health-related behavior within a social/cultural perspective.

Science.gov (United States)

Tod, David; Edwards, Christian; Hall, Gareth

2013-09-01

We examined relationships between drive for leanness and perceived media pressure to change appearance, internalization of an ideal physique, exercise frequency, and dieting. Men and women (N=353) completed the Drive for Leanness Scale, the Sociocultural Attitudes Toward Appearance Questionnaire-3, the Eating Attitudes Test-26, and a demographic inventory. Drive for leanness was significantly correlated with athletic internalization (.52), pressure to attain an ideal physique (.25), exercise frequency (.36), and dieting (.25). Structural equation modeling revealed a good fitting model (χ(2)=2.85, pdrive for leanness, which in turn predicted dieting and exercise. Results reveal social/cultural theory helps enhance the understanding of the drive for leanness and its relationship with health-related behavior. Copyright © 2013 Elsevier Ltd. All rights reserved.

Recovery of plutonium from lean organic in presence of Ru - activity

International Nuclear Information System (INIS)

Govindan, P.; Vijayan, K.S.; Dhamodharan, K.; Sharma, P.K.; Desigan, N.; Mohan, S.V.; Subba Rao, R.V.

2006-01-01

Recovery of plutonium from the scrubbed organic by uranous stabilized with hydrazine is carried out. It is observed that the quantitative stripping of plutonium is obtained by a single contact leaving organic with 25.0 mg/L of plutonium containing 0.468mCi/L Ru activity. The retention of plutonium in the lean organic may be attributed to the presence of degradation products and ruthenium activity may be due to the stable complex of ruthenium with TBP. The final strip product almost free from ruthenium is subjected to oxalate precipitation after pre concentration.The proposed method is applied to actual plant stream during reprocessing of high burn up fuel

Adiabatic burning velocity of H2-O2 mixtures diluted with CO2/N2/Ar

International Nuclear Information System (INIS)

Ratna Kishore, V.; Muchahary, Ringkhang; Ray, Anjan; Ravi, M.R.

2009-01-01

Global warming due to CO 2 emissions has led to the projection of hydrogen as an important fuel for future. A lot of research has been going on to design combustion appliances for hydrogen as fuel. This has necessitated fundamental research on combustion characteristics of hydrogen fuel. In this work, a combination of experiments and computational simulations was employed to study the effects of diluents (CO 2 , N 2 , and Ar) on the laminar burning velocity of premixed hydrogen/oxygen flames using the heat flux method. The experiments were conducted to measure laminar burning velocity for a range of equivalence ratios at atmospheric pressure and temperature (300 K) with reactant mixtures containing varying concentrations of CO 2 , N 2 , and Ar as diluents. Measured burning velocities were compared with computed results obtained from one-dimensional laminar premixed flame code PREMIX with detailed chemical kinetics and good agreement was obtained. The effectiveness of diluents in reduction of laminar burning velocity for a given diluent concentration is in the increasing order of argon, nitrogen, carbon dioxide. This may be due to increased capabilities either to quench the reaction zone by increased specific heat or due to reduced transport rates. The lean and stoichiometric H 2 /O 2 /CO 2 flames with 65% CO 2 dilution exhibited cellular flame structures. Detailed three-dimensional simulation was performed to understand lean H 2 /O 2 /CO 2 cellular flame structure and cell count from computed flame matched well with the experimental cellular flame. (author)

Lean With a Human Face

DEFF Research Database (Denmark)

Hasle, Peter; Jensen, Per Langaa

2008-01-01

The consequences for quality of work of lean manufacturing is discussed in the international litterature, and several authors suggest increased work speed, stress, and muscoskeletal diseases as a consequence of lean. The Danish experience with lean has been studied through interviews with managers...

JOYO MK-III performance test. Criticality test, excess reactivity measurement and burn-up coefficient measurement

International Nuclear Information System (INIS)

Maeda, Shigetaka; Sekine, Takashi; Kitano, Akihiro; Nagasaki, Hideaki

2005-03-01

The MK-III performance test began in June 2003 to fully characterize the upgraded core and heat transfer system of the experimental fast reactor JOYO. This paper describes the results of the approach to criticality, the excess reactivity evaluation and the burn-up coefficient measurement. In the approach to criticality test, the MK-III core achieved initial criticality at the control rod bank position of 412.8 mm on 14:03 July 2nd, 2003. Because the replacement of the outer two rows of reflector subassemblies with shielding subassemblies reduced the source range monitor signals by a factor of 3 at the same reactor power compared with those in the MK-II core, we measured the change of the monitor's response and determined the count rate 2x10 4 cps.' as an appropriate value judging the zero power criticality. In the excess reactivity evaluation, the zero power excess reactivity at 250degC was 2.99±0.10%Δk/kk' based on the measured critical rod bank position and the measured control rod worths. The predicted value by the JOYO core management code system HESTIA was 3.13±0.16%Δk/kk', showing good agreement with the measured value. The measured excess reactivity was within the safety requirement limit. In the burn-up coefficient measurement, the excess reactivity change versus the reactor burn-up was evaluated. The measurement method adopted was to measure the control rod positions during the rated power operation. A value of -2.12x10 -4 Δk/kk'/MWd was obtained as a measured burn-up coefficient. The value calculated by HESTIA was -2.12x10 -4 Δk/kk'/MWd, and it agreed well with the measured value. All technical safety requirements for MK-III core were satisfied and the calculation accuracy of the core management code system HESTIA was confirmed. (author)

A Case Study Improvement of a Testing Process by Combining Lean Management, Industrial Engineering and Automation Methods

Directory of Open Access Journals (Sweden)

Simon Withers

2013-07-01

Full Text Available Increasingly competitive market environments have forced not only large manufacturing, but also smalland-medium size enterprises (SME to look for means to improve their operations in order to increase competitive strength. This paper presents an adaptation and adoption by a UK SME engineering service organisation, of lean management, industrial engineering, and automation metods developed within larger organisations. This SME sought to improve the overall performance of one of its core testing processes. An exploratory analysis, based on the lean management concept of “value added” and work measurement technique “time study”, was developed and carried out in order to understand the current performance of a testing process for gas turbine fuel flow dividers. A design for the automation of some operations of the testing process was followed as an approach to reduce non-value added activities, and improve the overall efficiency of the testing process. The overall testing time was reduced from 12.41 to 7.93 hours (36.09 percent while the man hours and non-value added time were also reduced from 23.91 to 12.94 hours (45.87 percent and from 11.08 to 6.69 (39.67 percent hours respectively. This resulted in an increase in process efficiency in terms of man hours from 51.91 to 61.28 percent. The contribution of this paper resides in presenting a case study that can be used as a guiding reference for managers and engineers to undertake improvement projects, in their organisations, similar to the one presented in this paper.

Emission reductions through precombustion chamber design in a natural gas, lean burn engine

International Nuclear Information System (INIS)

Crane, M.E.; King, S.R.

1992-01-01

A study was conducted to evaluate the effects of various precombustion chamber design, operating and control parameters on the exhaust emissions of a natural gas engine. Analysis of the results showed that engine-out total hydrocarbons and oxides of nitrogen (NO x ) can be reduced, relative to conventional methods, through prechamber design. More specifically, a novel staged prechamber yielded significant reductions in NO x and total hydrocarbon emissions by promoting stable prechamber and main chamber ignition under fuel-lean conditions. Precise fuel control was also critical when balancing low emissions and engine efficiency (i.e., fuel economy). The purpose of this paper is to identify and explain positive and deleterious effects of natural gas prechamber design on exhaust emissions

A Methodology for the Assessment of Experiential Learning Lean: The Lean Experience Factory Study

Science.gov (United States)

De Zan, Giovanni; De Toni, Alberto Felice; Fornasier, Andrea; Battistella, Cinzia

2015-01-01

Purpose: The purpose of this paper is to present a methodology to assess the experiential learning processes of learning lean in an innovative learning environment: the lean model factories. Design/methodology/approach: A literature review on learning and lean management literatures was carried out to design the methodology. Then, a case study…

Applying lean thinking in construction

Directory of Open Access Journals (Sweden)

Remon Fayek Aziz

2013-12-01

Full Text Available The productivity of the construction industry worldwide has been declining over the past 40 years. One approach for improving the situation is using lean construction. Lean construction results from the application of a new form of production management to construction. Essential features of lean construction include a clear set of objectives for the delivery process, aimed at maximizing performance for the customer at the project level, concurrent design, construction, and the application of project control throughout the life cycle of the project from design to delivery. An increasing number of construction academics and professionals have been storming the ramparts of conventional construction management in an effort to deliver better value to owners while making real profits. As a result, lean-based tools have emerged and have been successfully applied to simple and complex construction projects. In general, lean construction projects are easier to manage, safer, completed sooner, and cost less and are of better quality. Significant research remains to complete the translation to construction of lean thinking in Egypt. This research will discuss principles, methods, and implementation phases of lean construction showing the waste in construction and how it could be minimized. The Last Planner System technique, which is an important application of the lean construction concepts and methodologies and is more prevalent, proved that it could enhance the construction management practices in various aspects. Also, it is intended to develop methodology for process evaluation and define areas for improvement based on lean approach principles.

Lean leadership: an ethnographic study

NARCIS (Netherlands)

Aij, K.H.; Visse, M.A.; Widdershoven, G.A.M.

2015-01-01

Purpose – The purpose of this study is to provide a critical analysis of contemporary Lean leadership in the context of a healthcare practice. The Lean leadership model supports professionals with a leading rolein implementing Lean.This article presents a case study focusing specifcally on

Burns education for non-burn specialist clinicians in Western Australia.

Science.gov (United States)

McWilliams, Tania; Hendricks, Joyce; Twigg, Di; Wood, Fiona

2015-03-01

Burn patients often receive their initial care by non-burn specialist clinicians, with increasingly collaborative burn models of care. The provision of relevant and accessible education for these clinicians is therefore vital for optimal patient care. A two phase design was used. A state-wide survey of multidisciplinary non-burn specialist clinicians throughout Western Australia identified learning needs related to paediatric burn care. A targeted education programme was developed and delivered live via videoconference. Pre-post-test analysis evaluated changes in knowledge as a result of attendance at each education session. Non-burn specialist clinicians identified numerous areas of burn care relevant to their practice. Statistically significant differences between perceived relevance of care and confidence in care provision were reported for aspects of acute burn care. Following attendance at the education sessions, statistically significant increases in knowledge were noted for most areas of acute burn care. Identification of learning needs facilitated the development of a targeted education programme for non-burn specialist clinicians. Increased non-burn specialist clinician knowledge following attendance at most education sessions supports the use of videoconferencing as an acceptable and effective method of delivering burns education in Western Australia. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

Corrective Action Plan for Corrective Action Unit 490: Station 44 Burn Area, Tonopah Test Range, Nevada

Energy Technology Data Exchange (ETDEWEB)

K. B. Campbell

2002-04-01

Corrective Action Unit (CAU) 490, Station 44 Burn Area is located on the Tonopah Test Range (TTR). CAU 490 is listed in the Federal Facility Agreement and Consent Order (FFACO, 1996) and includes for Corrective Action Sites (CASs): (1) Fire Training Area (CAS 03-56-001-03BA); (2) Station 44 Burn Area (CAS RG-56-001-RGBA); (3) Sandia Service Yard (CAS 03-58-001-03FN); and (4) Gun Propellant Burn Area (CAS 09-54-001-09L2).

Lean software development in action

CERN Document Server

Janes, Andrea

2014-01-01

This book illustrates how goal-oriented, automated measurement can be used to create Lean organizations and to facilitate the development of Lean software, while also demonstrating the practical implementation of Lean software development by combining tried and trusted tools. In order to be successful, a Lean orientation of software development has to go hand in hand with a company's overall business strategy. To achieve this, two interrelated aspects require special attention: measurement and experience management. In this book, Janes and Succi provide the necessary knowledge to establish "

Lean Management

OpenAIRE

Picot, Arnold

1994-01-01

In this article the possibility of increase of competitiveness of the domestic enterprises by means of Lean management system is considered, and also the analysis of introduction of the mentioned system at the Russian enterprises is carried out. Besides, the key conditions necessary for successful introduction of system are presented. Lean management is a world-spread way of solving the problems, aimed at making the company competitive; it is the organized activity of staff of the company, fo...

Study on laminar burning velocity of syngas-air premixed flames in various mixing conditions

International Nuclear Information System (INIS)

Lee, Kee Man; Jeong, Byeong Gyu; Lee, Seung Ro

2015-01-01

The laminar burning velocity of syngas-air premixed flames was measured with various equivalence ratios from 0.5 to 5.0 and a mole fraction of H 2 from 0.05 to 0.75. The laminar burning velocity was experimentally determined using a Bunsen flame according to the cone angle and surface area methods. A premixed code with a USC-II detailed reaction mechanism was used for the numerical calculations to predict the laminar burning velocity and to examine the relationship between the burning velocity enhancement and the hydrogen-related reactions. The results indicate that an appropriate method for the measurement of laminar burning velocity is necessary in the H 2 /CO/air syngas premixed flame. In addition, the burning velocity linearly increased with the increase of the H 2 mole fraction in the syngas mixture, although the burning velocity of H 2 was 10 times larger than that of CO. This result is attributed to the rapid production of H-radicals at the early stage of combustion. Furthermore, the predicted mole fractions of H and OH radicals increased with the increase of H 2 mole fraction for a lean syngas mixture. However, the mole fraction of OH radicals, an indicator of heat release rate, decreased for rich syngas mixture, resulting in a reduction of the laminar burning velocity, even with an increase of the H 2 mole fraction.

Experience in applying lean production concepts in the service sector

Directory of Open Access Journals (Sweden)

Dyrina Evgeniya

2016-01-01

Full Text Available This article describes the experience of implementing lean production tools in the company services. The authors have based the research of the chef’s work, built Ishikawa’s diagram on one of the most important problems of the company and proposed the cyclogram of cooks at work. Problems were identified using this technology after analyzing domestic and foreign experience in implementing lean production. The algorithm for implementing lean production and the necessary tools for achievement of the goals of the enterprise were authored on the basis of experience gained analyses of theoretical materials, which were tested on the basis of the small business «White Dragon».

Implementing lean in Malaysian universities: Lean awareness level in an engineering faculty of a local university

Science.gov (United States)

Azim Khairi, M.; Rahman, Mohamed Abd

2018-01-01

Many academic articles were published in Malaysia promoting the goodness of lean in manufacturing and industrial sectors but less attention was apparently given to the possibility of obtaining the same universal benefits when applying lean in non-manufacturing sectors especially higher education. This study aims to determine the level of lean awareness among a local university’s community taking its Faculty of Engineering (FoE) as the case study. It also seeks to identify typical FoE’s staff perception on lean regarding its benefits and the obstacles in implementing it. A web-based survey using questionnaires was carried out for 215 respondents consisting of academic and administrative staff of the faculty. Statistical Package for the Social Science (SPSS) was used to analyze the survey data collected. A total of 13.95% of respondents returned the forms. Slightly more than half of those responded (56.7%) have encountered some of the lean terms with mean 1.43 and standard deviation 0.504. However, the large amount of standard deviation somewhat indicates that the real level of lean awareness of FoE as a group was low. In terms of lean benefits, reduction of waste was favored (93.3%) by the respondents with mean 0.93 and standard deviation 0.254. For obstacles in implementing lean, lack of knowledge was selected by most respondents (86.7%) to be the major factor with mean 0.87 and standard deviation 0.346. Through the analysis done, the study may conclude that level of lean awareness among the university‘s community was low thus may hinder implementation of lean concept.

A Web-Based Lean Simulation Game for Office Operations: Training the Other Side of a Lean Enterprise

Science.gov (United States)

Kuriger, Glenn W.; Wan, Huang-da; Mirehei, S. Moussa; Tamma, Saumya; Chen, F. Frank

2010-01-01

This research proposes a Web-based version of a lean office simulation game (WeBLOG). The game is designed to be used to train lean concepts to office and administrative personnel. This group belongs to the frequently forgotten side of a lean enterprise. Over four phases, the game presents the following seven lean tools: one-piece flow,…

The maintenance management for lean organization

Directory of Open Access Journals (Sweden)

Daniel D. GEORGESCU

2010-12-01

Full Text Available The goal of lean maintenance approach is to maintain organization international competitiveness. In the spirit of continuously improvement, in the paper it is shown how by adjusting some Lean manufacturing specific techniques for Total Productive Maintenance (TPM system, was born new maintenance system named Lean TPM. This is a systemic approach with three techniques, which don’t exclude specific techniques of TPM pillars, but complete them: the 7Ss as a critical first step in any improvement program; instantaneous maintenance; improvement setup operations. In the spirit of Lean principle, Lean TPM adjusts overall equipment effectiveness concept for all supply-chain from supplier to customer. Maintaining equipment in its optimal state and continually improving its productivity is the whole strategy behind Lean TPM.

The human side of lean teams.

Science.gov (United States)

Wackerbarth, Sarah B; Strawser-Srinath, Jamie R; Conigliaro, Joseph C

2015-05-01

Organizations use lean principles to increase quality and decrease costs. Lean projects require an understanding of systems-wide processes and utilize interdisciplinary teams. Most lean tools are straightforward, and the biggest barrier to successful implementation is often development of the team aspect of the lean approach. The purpose of this article is to share challenges experienced by a lean team charged with improving a hospital discharge process. Reflection on the experience provides an opportunity to highlight lessons from The Team Handbook by Peter Scholtes and colleagues. To improve the likelihood that process improvement initiatives, including lean projects, will be successful, organizations should consider providing training in organizational change principles and team building. The authors' lean team learned these lessons the hard way. Despite the challenges, the team successfully implemented changes throughout the organization that have had a positive impact. Training to understand the psychology of change might have decreased the resistance faced in implementing these changes. © 2014 by the American College of Medical Quality.

Industry 4.0 implies lean manufacturing: Research activities in industry 4.0 function as enablers for lean manufacturing

Directory of Open Access Journals (Sweden)

Adam Sanders

2016-09-01

Full Text Available Purpose: Lean Manufacturing is widely regarded as a potential methodology to improve productivity and decrease costs in manufacturing organisations. The success of lean manufacturing demands consistent and conscious efforts from the organisation, and has to overcome several hindrances. Industry 4.0 makes a factory smart by applying advanced information and communication systems and future-oriented technologies. This paper analyses the incompletely perceived link between Industry 4.0 and lean manufacturing, and investigates whether Industry 4.0 is capable of implementing lean. Executing Industry 4.0 is a cost-intensive operation, and is met with reluctance from several manufacturers. This research also provides an important insight into manufacturers’ dilemma as to whether they can commit into Industry 4.0, considering the investment required and unperceived benefits. Design/methodology/approach: Lean manufacturing is first defined and different dimensions of lean are presented. Then Industry 4.0 is defined followed by representing its current status in Germany. The barriers for implementation of lean are analysed from the perspective of integration of resources. Literatures associated with Industry 4.0 are studied and suitable solution principles are identified to solve the abovementioned barriers of implementing lean. Findings: It is identified that researches and publications in the field of Industry 4.0 held answers to overcome the barriers of implementation of lean manufacturing. These potential solution principles prove the hypothesis that Industry 4.0 is indeed capable of implementing lean. It uncovers the fact that committing into Industry 4.0 makes a factory lean besides being smart. Originality/value: Individual researches have been done in various technologies allied with Industry 4.0, but the potential to execute lean manufacturing was not completely perceived. This paper bridges the gap between these two realms, and identifies

An exploratory analysis for Lean and Six Sigma implementation in hospitals: Together is better?

Science.gov (United States)

Lee, Jung Young; McFadden, Kathleen L; Gowen, Charles R

2016-12-22

Despite the increasing interest for Lean and Six Sigma implementations in hospitals, there has been little empirical evidence that goes beyond descriptive case studies to address the current status and the effectiveness of the implementations. The aim of this study was to explore existing patterns of Lean and Six Sigma implementation in U.S. hospitals and compare the performance of the different patterns. We collected data from 215 U.S. hospitals via a survey that includes measurement items developed from related literature. Using the cross-sectional data, we conducted a cluster analysis, followed by t tests, chi-square tests, and regression analyses for cluster verification. The cluster analysis identifies two clusters, a Moderate Six Sigma group and a Lean Six Sigma group. Results show that the Lean Six Sigma group outperforms the Moderate Six Sigma group across many performance dimensions: responsiveness capability, patient safety, and possibly cost saving. In addition, the Lean Six Sigma group tends to be composed of larger, private teaching hospitals located in more urban areas, and they employ more resources for quality improvement. Our research contributes to the quality management literature by supporting the possible complementary relationship between Lean and Six Sigma in hospitals. Our study encourages practitioners and managers to pay more attention to Lean implementation. Although Lean seems to be conducted in a limited fashion in many hospitals, it should be expanded and combined with Six Sigma for better results.

Genetic variation in efficiency to deposit fat and lean meat in Norwegian Landrace and Duroc pigs.

Science.gov (United States)

Martinsen, K H; Ødegård, J; Olsen, D; Meuwissen, T H E

2015-08-01

Feed costs amount to approximately 70% of the total costs in pork production, and feed efficiency is, therefore, an important trait for improving pork production efficiency. Production efficiency is generally improved by selection for high lean growth rate, reduced backfat, and low feed intake. These traits have given an effective slaughter pig but may cause problems in piglet production due to sows with limited body reserves. The aim of the present study was to develop a measure for feed efficiency that expressed the feed requirements per 1 kg deposited lean meat and fat, which is not improved by depositing less fat. Norwegian Landrace ( = 8,161) and Duroc ( = 7,202) boars from Topigs Norsvin's testing station were computed tomography scanned to determine their deposition of lean meat and fat. The trait was analyzed in a univariate animal model, where total feed intake in the test period was the dependent variable and fat and lean meat were included as random regression cofactors. These cofactors were measures for fat and lean meat efficiencies of individual boars. Estimation of fraction of total genetic variance due to lean meat or fat efficiency was calculated by the ratio between the genetic variance of the random regression cofactor and the total genetic variance in total feed intake during the test period. Genetic variance components suggested there was significant genetic variance among Norwegian Landrace and Duroc boars in efficiency for deposition of lean meat (0.23 ± 0.04 and 0.38 ± 0.06) and fat (0.26 ± 0.03 and 0.17 ± 0.03) during the test period. The fraction of the total genetic variance in feed intake explained by lean meat deposition was 12% for Norwegian Landrace and 15% for Duroc. Genetic fractions explained by fat deposition were 20% for Norwegian Landrace and 10% for Duroc. The results suggested a significant part of the total genetic variance in feed intake in the test period was explained by fat and lean meat efficiency. These new

Lean Production Applications in a Manufacturing Company

OpenAIRE

Ali Görener; Humeyra Baser; Ali Turkyilmaz

2013-01-01

Lean production is a production model which comes about the pursuit of companies to be able to meet competition and make effective production. The main purpose of lean production is to get control about the wastage. This study includes the requirements for the success of the lean production and how the lean production system can be established. In this paper, lean production techniques were applied to the electric water heater line. Measurements using lean initiatives were made, operation cyc...

Burning test on a storage drum filled with a mixture of sodiumnitrate and bitumen

International Nuclear Information System (INIS)

Knotik, K.; Leichter, P.; Spalek, K.

1979-01-01

A burning test on a common storage drum filled with a mixture of sodiumnitrate and bitumen was carried out to show the incinerability of said mixture. A 50 l mild steel drum was filled with 80,7 kg sodiumnitrate/bitumen-mixture. The drum was packed in a 200 l mild steel drum, the remaining space was filled with enough sand to cover the top of the inner drum with 15 cm of sand. The sand packing was then soaked with 70 l of light distillate fuel and ignited. The fuel burned until self-extinguishing occurred. 30 % (22,2 l) of the fuel was burned. 0,7 % of the energy potential was absorbed in the sand layer. The highest measured temperature was 34 0 C at the top of the test drum. It can be concluded, that even under severe external actions the ignition temperature of 400 0 C for bitumen/waste mixtures cannot be reached, providing correct technical storage conditions, which means that the void space in the cavities is filled with unburnable absorbing material like sand or salt. (author)

Development of lean burn gas engines using pilot fuel for ignition source; Developpement d'un moteur a gaz avec pre-injection de carburant pour la source d'allumage

Energy Technology Data Exchange (ETDEWEB)

Sakonji, T.; Saito, H.; Sakurai, T. [Tokyo Gas Co., Ltd. (Japan); Hirashima, T.; Kanno, K. [Nissan Diesel Motor Co., Ltd. (Japan)

2000-07-01

A development was conducted to investigate the performance of an open chamber gas engine with pilot fuel for ignition source. Experiments were conducted by using a gas engine equipped with a common-rail injection system. Main gas fuel is supplied to the engine cylinder, and then a small quantity of diesel fuel (approximately 1 % of total fuel energy input) was injected into the main chamber for ignition. The single cylinder prototype gas engine has demonstrated superior performance, such as, a shaft-end thermal efficiency of 36.7% with NO{sub x} level of 0.4 g/kW-h, which equals those of conventional spark ignited pre-chamber lean burn gas engines. For the next step, the multi-cylinder gas engine has been developed. That has 138 mm bore, 142 mm stroke, V8 configuration and 229 kW engine output 1500 rpm. This engine can also run with only diesel fuel for Standby-Power-Concurrent Co-generation. (authors)

Lean Production Applications in a Manufacturing Company

Directory of Open Access Journals (Sweden)

Ali Görener

2016-01-01

Full Text Available Lean production is a production model which comes about the pursuit of companies to be able to meet competition and make effective production. The main purpose of lean production is to get control about the wastage. This study includes the requirements for the success of the lean production and how the lean production system can be established. In this paper, lean production techniques were applied to the electric water heater line. Measurements using lean initiatives were made, operation cycle times were determined, and Kaizen improvement methods and line balancing methods were applied according to the results. And the last section of study showed conclusion of lean implementation.

The lean service machine.

Science.gov (United States)

Swank, Cynthia Karen

2003-10-01

Jefferson Pilot Financial, a life insurance and annuities firm, like many U.S. service companies at the end of the 1990s was looking for new ways to grow. Its top managers recognized that JPF needed to differentiate itself in the eyes of its customers, the independent life-insurance advisers who sell and service policies. To establish itself as these advisers' preferred partner, it set out to reduce the turnaround time on policy applications, simplify the submission process, and reduce errors. JPF's managers looked to the "lean production" practices that U.S. manufacturers adopted in response to competition from Japanese companies. Lean production is built around the concept of continuous-flow processing--a departure from traditional production systems, in which large batches are processed at each step. JPF appointed a "lean team" to reengineer its New Business unit's operations, beginning with the creation of a "model cell"--a fully functioning microcosm of JPF's entire process. This approach allowed managers to experiment and smooth out the kinks while working toward an optimal design. The team applied lean-manufacturing practices, including placing linked processes near one another, balancing employees' workloads, posting performance results, and measuring performance and productivity from the customer's perspective. Customer-focused metrics helped erode the employees' "My work is all that matters" mind-set. The results were so impressive that JPF is rolling out similar systems across many of its operations. To convince employees of the value of lean production, the lean team introduced a simulation in which teams compete to build the best paper airplane based on invented customer specifications. This game drives home lean production's basic principles, establishing a foundation for deep and far-reaching changes in the production system.

Study and application on lean resin converting in uranium mill

International Nuclear Information System (INIS)

Zhao Shaoxi; Huang Qijin; Zhu Shuguang; Yi Faqing; Du Wenjie

2012-01-01

The field test about sulphuric acid used to convert lean resin was finished. The results indicated sulphuric acid could replace chlorin in lean resin and could be reclaimed to desorption procedure. The consumption of NaCl decreased, the chlorin concentration of tailing decreased too. Both of uranium loss and waste water volume were reduced. The uranium concentration of tailing decreased and energy saving and emission reduction can be achieved. (authors)

Reliability enhancement through optimal burn-in

Science.gov (United States)

Kuo, W.

1984-06-01

A numerical reliability and cost model is defined for production line burn-in tests of electronic components. The necessity of burn-in is governed by upper and lower bounds: burn-in is mandatory for operation-critical or nonreparable component; no burn-in is needed when failure effects are insignificant or easily repairable. The model considers electronic systems in terms of a series of components connected by a single black box. The infant mortality rate is described with a Weibull distribution. Performance reaches a steady state after burn-in, and the cost of burn-in is a linear function for each component. A minimum cost is calculated among the costs and total time of burn-in, shop repair, and field repair, with attention given to possible losses in future sales from inadequate burn-in testing.

Effect of Lewis number on ball-like lean limit flames

KAUST Repository

Zhou, Zhen

2017-10-13

The lean limit flames for three different fuel compositions premixed with air, representing three different mixture Lewis numbers, stabilized inside a tube in a downward flow are examined by experiments and numerical simulations. The CH* chemiluminescence distribution in CH4–air and CH4–H2–air flames and the OH* chemiluminescence distribution in H2–air flames are recorded in the experiments. Cell-like flames are observed for the CH4–air mixture for all tested equivalence ratios. However, for CH4–H2–air and H2–air flames, ball-like lean limit flames are observed. Flame temperature fields are measured using Rayleigh scattering. The experimentally observed lean limit flames are predicted qualitatively by numerical simulation with the mixture-averaged transport model and skeletal mechanism of CH4. The results of the simulations show that the entire lean limit flames of CH4–H2–air and H2–air mixtures are located inside a recirculation zone. However, for the lean limit CH4–air flame, only the leading edge is located inside the recirculation zone. A flame structure with negative flame displacement speed is observed for the leading edges of the predicted lean limit flames with all three different fuel compositions. As compared with 1D planar flames, the fuel transport caused by convection is less significant in the present 2D lean limit flames for the three different fuel compositions. For the trailing edges of the three predicted lean limit flames, a diffusion dominated flame structure is observed.

Training for successful lean manufacturing implementation

OpenAIRE

Ichimura, Maki; Jahankhani, Hamid; Arunachalam, Subramaniam

2006-01-01

Implementing lean manufacturing is a complex and everlasting task. The workers involving in production processes are the pivot of the lean manufacturing implementation. Training is known as a vehicle to assist the implementation process. Despite awareness of the training importance, so far, a little is available to assist to organise an efficient training. This paper summarises the overview of lean manufacturing and discuss the importance of human resource within lean implementation process. ...

Laminar burning velocities at elevated pressures for gasoline and gasoline surrogates associated with RON

KAUST Repository

Mannaa, Ossama

2015-06-01

The development and validation of a new gasoline surrogate using laminar flame speed as a target parameter is presented. Laminar burning velocities were measured using a constant-volume spherical vessel with ignition at the center of the vessel. Tested fuels included iso-octane, n-heptane, toluene, various mixtures of primary reference fuels (PRFs) and toluene reference fuels (TRFs) and three gasoline fuels of 70, 85 and 95 RON (FACE J, C and F) at the initial temperature of 358K and pressures up to 0.6MPa in the equivalence ratio ranging from 0.8 to 1.6. Normalized laminar burning velocity data were mapped into a tri-component mixture space at different experimental conditions to allocate different gasoline surrogates for different gasoline fuels, having RON of 70, 85 and 95. The surrogates of TRF-70-4 (17.94% iso-C8H18 +42.06% n-C7H16 +40% C7H8), TRF-85-1 (77.4% iso-C8H18 +17.6% n-C7H16 +5% C7H8), and TRF-95-1 (88.47% iso-C8H18 +6.53% n-C7H16 +5% C7H8) of RON 70, 85 and 95, respectively, are shown to successfully emulate the burning rate characteristics of the gasoline fuels associated with these RONs under the various experimental conditions investigated. An empirical correlation was derived to obtain laminar burning velocities at pressures that are experimentally unattainable as high as 3.0MPa. Laminar burning velocities were comparable to the simulated values for lean and stoichiometric flames but they were relatively higher than the simulated values for rich flames. A flame instability assessment was conducted by determining Markstein length, critical Pecklet number, and critical Karlovitz number at the onset of flame instability.

Lean Six Sigma in financial services

NARCIS (Netherlands)

de Koning, H.; Does, R.J.M.M.; Bisgaard, S.

2008-01-01

Lean Thinking and Six Sigma are typically considered as separate approaches to process innovation, with complementary strengths. When combined as Lean Six Sigma, this approach provides a unified framework for systematically developing innovations. Lean Six Sigma can also bring about significant

Healthy Lean Through HRD

DEFF Research Database (Denmark)

Jørgensen, Frances

2008-01-01

The paper reports on findings from the initial, exploratory phase of a longitudinal research study aimed at developing a framework for implementing lean while ensuring employee well-being. Data from observations and in-depth dialogues with persons involved in lean implementation, along...

The integration of lean, green and best practice business principles

Directory of Open Access Journals (Sweden)

Annelize Wiese

2015-10-01

Full Text Available Background: Whilst there are separate streams of established research on lean, green and best practice initiatives, the intersection of these three strategic principles has not been addressed extensively in the past. Objectives: In this study a framework to integrate lean, green and best practice principles into an integrated business model was developed as a strategy for businesses to develop sustainable competitive advantages. Method: A descriptive case study was conducted on Toyota South Africa Motors (TSAM to understand whether a clear link between the company’s environmental approach, lean principles and established best practice culture could be determined. In addition, the case study tested the view that the implementation of these three principles concurrently resulted in improved business results. Results: The main findings of the study revealed that TSAM’s commitment to lean, green and best practice business principles contributed and was directly linked to its business success in terms of sales and market position. Conclusion: It is recommended that businesses implement an integrated lean, green and best practice business model as a strategy to reduce costs and sustainably enhance profitably and competitiveness.

Lean management - an effective way to arrange maintenance?; Lean Management - ein effektiver Weg zur Gestaltung der Instandhaltung?

Energy Technology Data Exchange (ETDEWEB)

Tschuschke, W. [Inst. fuer Instandhaltung gGmbH, Iserlohn (Germany)

1996-08-01

Lean management/lean production wishes to attain more through intelligent operation system/production at less expense (personnel, materials, energy, costs). The object is not harder but more intelligent and production work; we do not need to run faster but to find shorter routes. The idea of lean management`s effects and changes have consequences for the field of maintenance as an equivalent and legitimate business area which are discussed in this paper. (orig.) [Deutsch] Lean Management/Lean Production will durch ein intelligentes Arbeitssystem/Produzieren mit weniger Aufwand (Personal, Material, Energie, Kosten) mehr erreichen. Ziel ist nicht das haertere, sondern das intelligentere und produktivere Arbeiten; wir sollen nicht schneller laufen, sondern kuerzere Wege finden. Fuer den Bereich Instandhaltung als gleichwertiger und gleichberechtigter Unternehmensbereich haben die Gedanken des Lean Managements Auswirkungen und Veraenderungen zur Folge, die im Beitrag genannt werden. (orig.)

Lean manufacturing in Indian context: A survey

Directory of Open Access Journals (Sweden)

Rakesh Kumar

2015-04-01

Full Text Available This paper is an attempt to examine the implementation of Lean Manufacturing system in the Indian industries. Predominant elements of Lean Manufacturing, benefits gained after its implementation and obstacles observed by Indian Industry have been recognized. The results of this survey support the opinion that Lean Manufacturing had potential to improve the organizational performance of Indian industries. Nevertheless, Indian industries are required to be passionate to transform their manufacturing by adopting Lean manufacturing to gain the full benefits. A large numbers of literature papers are available on the better side of Lean manufacturing approach and its benefits gained by manufacturing organizations after implementation. But the adverse impacts of Lean manufacturing are not discussed to a great extent. Some drawbacks of Lean manufacturing are also highlighted in this paper.

The Finnish healthcare services lean management.

Science.gov (United States)

Hihnala, Susanna; Kettunen, Lilja; Suhonen, Marjo; Tiirinki, Hanna

2018-02-05

Purpose The purpose of this paper is to discuss health services managers' experiences of management in a special health-care unit and development efforts from the point of view of the Lean method. Additionally, the aim is to deepen the knowledge of the managers' work and nature of the Lean method development processes in the workplace. The research focuses on those aspects and results of Lean method that are currently being used in health-care environments. Design/methodology/approach These data were collected through a number of thematic interviews. The participants were nurse managers ( n = 7) and medical managers ( n = 7) who applied Lean management in their work at the University Hospital in the Northern Ostrobothnia Health Care District. The data were analysed with a qualitative content analysis. Findings A common set of values in specialized health-care services, development of activities and challenges for management in the use of the Lean manager development model to improve personal management skills. Practical implications Managers in specialized health-care services can develop and systematically manage with the help of the Lean method. This emphasizes assumptions, from the point of view of management, about systems development when the organization uses the Lean method. The research outcomes originate from specialized health-care settings in Finland in which the Lean method and its associated management principles have been implemented and applied to the delivery of health care. Originality/value The study shows that the research results and in-depth knowledge on Lean method principles can be applied to health-care management and development processes. The research also describes health services managers' experiences of using the Lean method. In the future, these results can be used to improve Lean management skills, identify personal professional competencies and develop skills required in development processes. Also, the research findings can be used

Study on laminar burning velocity of syngas-air premixed flames in various mixing conditions

Energy Technology Data Exchange (ETDEWEB)

Lee, Kee Man; Jeong, Byeong Gyu [Sunchon National University, Suncheon (Korea, Republic of); Lee, Seung Ro [Chonbuk National University, Jeonju (Korea, Republic of)

2015-07-15

The laminar burning velocity of syngas-air premixed flames was measured with various equivalence ratios from 0.5 to 5.0 and a mole fraction of H{sub 2} from 0.05 to 0.75. The laminar burning velocity was experimentally determined using a Bunsen flame according to the cone angle and surface area methods. A premixed code with a USC-II detailed reaction mechanism was used for the numerical calculations to predict the laminar burning velocity and to examine the relationship between the burning velocity enhancement and the hydrogen-related reactions. The results indicate that an appropriate method for the measurement of laminar burning velocity is necessary in the H{sub 2}/CO/air syngas premixed flame. In addition, the burning velocity linearly increased with the increase of the H{sub 2} mole fraction in the syngas mixture, although the burning velocity of H{sub 2} was 10 times larger than that of CO. This result is attributed to the rapid production of H-radicals at the early stage of combustion. Furthermore, the predicted mole fractions of H and OH radicals increased with the increase of H{sub 2} mole fraction for a lean syngas mixture. However, the mole fraction of OH radicals, an indicator of heat release rate, decreased for rich syngas mixture, resulting in a reduction of the laminar burning velocity, even with an increase of the H{sub 2} mole fraction.

The performance effect of the Lean package – a survey study using a structural equation model

DEFF Research Database (Denmark)

Kristensen, Thomas Borup; Israelsen, Poul

Purpose - Our aim is to test and validate a system-wide approach using mediating relationships in a structural equation model in order to understand how the practices of Lean affect performance. Design/methodology/approach – A cross-sectional survey with 200 responding companies indicating...... that they use Lean. This is analyzed in a structural quation model setting. Findings - Previous quantitative research has shown mixed results for the performance of Lean because they have not addressed the system-wide mediating relations between Lean practices. We find that Companies using a system...... practices in creating improved performance. Hence, we develop a new systemwide structural equation model approach with multiple mediations, and we validate this with substantial tests....

Inducible satellite cell depletion attenuates skeletal muscle regrowth following a scald-burn injury.

Science.gov (United States)

Finnerty, Celeste C; McKenna, Colleen F; Cambias, Lauren A; Brightwell, Camille R; Prasai, Anesh; Wang, Ye; El Ayadi, Amina; Herndon, David N; Suman, Oscar E; Fry, Christopher S

2017-11-01

Severe burns result in significant skeletal muscle cachexia that impedes recovery. Activity of satellite cells, skeletal muscle stem cells, is altered following a burn injury and likely hinders regrowth of muscle. Severe burn injury induces satellite cell proliferation and fusion into myofibres with greater activity in muscles proximal to the injury site. Conditional depletion of satellite cells attenuates recovery of myofibre area and volume following a scald burn injury in mice. Skeletal muscle regrowth following a burn injury requires satellite cell activity, underscoring the therapeutic potential of satellite cells in the prevention of prolonged frailty in burn survivors. Severe burns result in profound skeletal muscle atrophy; persistent muscle atrophy and weakness are major complications that hamper recovery from burn injury. Many factors contribute to the erosion of muscle mass following burn trauma, and we have previously shown concurrent activation and apoptosis of muscle satellite cells following a burn injury in paediatric patients. To determine the necessity of satellite cells during muscle recovery following a burn injury, we utilized a genetically modified mouse model (Pax7 CreER -DTA) that allows for the conditional depletion of satellite cells in skeletal muscle. Additionally, mice were provided 5-ethynyl-2'-deoxyuridine to determine satellite cell proliferation, activation and fusion. Juvenile satellite cell-wild-type (SC-WT) and satellite cell-depleted (SC-Dep) mice (8 weeks of age) were randomized to sham or burn injury consisting of a dorsal scald burn injury covering 30% of total body surface area. Both hindlimb and dorsal muscles were studied at 7, 14 and 21 days post-burn. SC-Dep mice had >93% depletion of satellite cells compared to SC-WT (P satellite cell proliferation and fusion. Depletion of satellite cells impaired post-burn recovery of both muscle fibre cross-sectional area and volume (P satellite cells in the aetiology of lean

Skaber lean bedre arbejdsmiljø?

DEFF Research Database (Denmark)

Hansen, Nanette Juhler

2007-01-01

rationalization strategies, among others Lean, claim to improve working conditions. The aim of this thesis is to identify whether the application of Lean strategies leads to a reduction of the occupational health and safety problem repetitive work. Repetitive work is a problem created by the Taylorisation of work......, and therefore it is to be expected that a break with one or more of the Tayloristic principles can lead to a reduction of repetitive work. This thesis points out a number of areas within which Lean breaks with Tayloristic principles, whilst other principles are maintained. These breaks between Lean...... and Taylorism are also found in the study of the case company. By linking breaks with Taylorism with solutions for the reduction of repetitive work, I point out a number of openings in Lean that may lead to a reduction of repetitive work. By using the concept of openings I present the possibilities offered...

TOWARDS GREEN THROUGH LEAN/LEAN SIX SIGMA APPROACHES: A LITERATURE REVIEW AT SERVICE INDUSTRY

Directory of Open Access Journals (Sweden)

RODRIGO GOYANNES GUSMÃO CAIADO

2017-08-01

Full Text Available In the last decades, sustainable development have increasingly gained importance to service industry and lean/Six Sigma approaches are becoming more and more outstanding in order to improve sustainability performance. In the post-modern era the integration between those approaches are necessary in order to aid organisations to balance the need for operational efficiency in their production and service systems with environmental commitment and social fairness. Because of that, Lean Six Sigma practices are progressively becoming widespread in studies about service, as way to improve quality, efficiency, effectiveness and sustainability of services. The purpose of this paper is to critically review the Lean and Lean Six Sigma (L6σ methodologies and highlight their importance to achieve sustainable development in service industry. To do this, a systematic literature review (SLR of the subjects under investigation was conducted. We examine the compatibility and divergences of the green, lean and Six Sigma concepts and implications regarding its sustainable implementation in service industry. The study has two major contributions. First, it is one of the first researches that investigate the potential benefits of integrating green, lean and Six Sigma in service sector. Second, it supports and expands current literature, providing both academicians and practitioners a better panorama to understand the present status of L6σ for achieving sustainability in service sector.

Exploiting HRM in support of lean manufacturing

DEFF Research Database (Denmark)

Jørgensen, Frances; Matthiesen, Rikke

The purpose of this paper is to investigate the ways in HRM practices are-and could potentially be-exploited to support lean manufacturing in practice. First, a review of the pertinent literature regarding HRM, SHRM, and lean manufacturing is presented to provide an understanding of the mechanisms...... by which HRM practices could, theoretically, be used to support a lean implementation. Data presented in the paper are derived from 1) a longitudinal case study on lean implementation and 2) from managers currently involved with lean manufacturing in a second company. The relevant literature and the data...... depicting the potential role in supporting HRM/lean integrated practices. The analysis of the model with respect to the theoretical background emphasizes a number of areas in which HRM could be more fully exploited in order to more successfully support lean implementation, for example, by stressing HRM...

Lean Transformation Guidance: Why Organizations Fail To Achieve and Sustain Excellence Through Lean Improvement

OpenAIRE

Mohammed Hamed Ahmed

2013-01-01

Many companies are complaining that lean didn’t achieve their long-term goals, and the improvement impact was very short-lived. 7 out of each 10 lean projects fail as companies try to use lean like a toolkit, copying and pasting the techniques without trying to adapt the employee’s culture, manage the improvement process, sustain the results, and develop their leaders. When the Toyota production system was created, the main goal was to remove wastes from the shop floor us...

An empirical review of lean manufacturing and their strategies

Directory of Open Access Journals (Sweden)

Virender Chahal

2017-07-01

Full Text Available The theory of lean manufacturing provides the quality of the products in minimum cost and pro-vides customer satisfaction. Today, the competition level is very high and every industry tries to supply high quality products in nominal cost, so lean is the latest tool to achieve. The objective of this paper is to study different lean concepts under various lean strategies. This study helps to find out the status of lean manufacturing and its ways of implementation. Also in this paper, there is a discussion about lean manufacturing concept, lean waste, lean strategies, lean barriers and cycle of lean implementation. This paper presents a literature review to clear the status of lean manufacturing and their strategies with help of collection of relevant papers.

Implementing Lean Health Reforms in Saskatchewan

Directory of Open Access Journals (Sweden)

Greg Marchildon

2013-07-01

Full Text Available Saskatchewan has gone further than any other Canadian province in implementing health system process improvements using Lean, a production line discipline that originated with the automobile industry. The goal of the Lean reform is to reduce waste and improve quality and overall health system performance by long-term changes in behaviour. Lean enjoys a privileged position on the provincial government’s agenda because of the policy’s championing by the Deputy Minister of Health and the policy’s fit with the government’s patient-centred care agenda. The implementation of reform depends on a major investment of time in the training and Lean-certification of key leaders and managers in the provincial health system. The Saskatchewan Union of Nurses, the union representing the single largest group of health workers in the province, has agreed to co-operate with the provincial government in implementing Lean-type reforms. Thus far, the government has had limited independent evaluation of Lean while internal evaluations claim some successes.

Does Lean Improve Labor Standards? Management and Social Performance in the Nike Supply Chain

OpenAIRE

Distelhorst, Greg; Hainmueller, Jens; Locke, Richard M.

2016-01-01

This study tests the hypothesis that lean manufacturing improves the social performance of manufacturers in emerging markets. We analyze an intervention by Nike Inc. to promote the adoption of lean manufacturing in its apparel supply chain across eleven developing countries. Using difference-in-differences estimates from a panel of over three hundred factories, we find that lean adoption was associated with a 15 percentage point reduction in noncompliance with labor standards t...

Impact of stress-induced diabetes on outcomes in severely burned children.

Science.gov (United States)

Finnerty, Celeste C; Ali, Arham; McLean, Josef; Benjamin, Nicole; Clayton, Robert P; Andersen, Clark R; Mlcak, Ronald P; Suman, Oscar E; Meyer, Walter; Herndon, David N

2014-04-01

Post-burn hyperglycemia leads to graft failure, multiple organ failure, and death. A hyperinsulinemic-euglycemic clamp is used to keep serum glucose between 60 and 110 mg/dL. Because of frequent hypoglycemic episodes, a less-stringent sliding scale insulin protocol is used to maintain serum glucose levels between 80 and 160 mg/dL after elevations >180 mg/dL. We randomized pediatric patients with massive burns into 2 groups, patients receiving sliding scale insulin to lower blood glucose levels (n = 145) and those receiving no insulin (n = 98), to determine the differences in morbidity and mortality. Patients 0 to 18 years old with burns covering ≥ 30% of the total body surface area and not randomized to receive anabolic agents were included in this study. End points included glucose levels, infections, resting energy expenditure, lean body mass, bone mineral content, fat mass, muscle strength, and serum inflammatory cytokines, hormones, and liver enzymes. Maximal glucose levels occurred within 6 days of burn injury. Blood glucose levels were age dependent, with older children requiring more insulin (p patients not receiving insulin, only in patients who received insulin (p patients receiving insulin (p Burn-induced hyperglycemia develops in a subset of severely burned children. Length of stay was reduced in the no insulin group, and there were no deaths in this group. Administration of insulin positively impacted bone mineral content and muscle strength, but increased resting energy expenditure, hypoglycemic episodes, and mortality. New glucose-lowering strategies might be needed. Copyright © 2014 American College of Surgeons. Published by Elsevier Inc. All rights reserved.

LEAN AND SIX SIGMA CONCEPTS APPLICATION IN PHARMACEUTICAL INDUSTRY

Directory of Open Access Journals (Sweden)

Katarina Pavlović

2012-03-01

Full Text Available LEAN thinking and Six Sigma have been utilized by manufacturing industries to decrease cost and improve quality and productivity by reducing variation and production defects [1]. Because of the dramatic successes in manufacturing, there is rising interest among companies in the pharmaceutical industry, which chooses to implement LEAN in order to accomplish such goals as decreased wait time to release product to the market, reduce production waste, and improve communication with end users and raize quality level both in the production and in testing laboratories. In this article, basics of LEAN and Six Sigma are presented and suggestion was given for application of their concepts in pharmaceutical industry together with harmonization with legal regulation represented by requirements Good Manufacturing Practice (cGMP, in order to work "smarter", more cost-effectively and avoid was ting time and other resources.

LEAN AND SIX SIGMA CONCEPTS - APPLICATION IN PHARMACEUTICAL INDUSTRY

Directory of Open Access Journals (Sweden)

Katarina Pavlović

2011-06-01

Full Text Available LEAN thinking and Six Sigma have been utilized by manufacturing industries to decrease cost and improve quality and productivity by reducing variation and production defects. Because of the dramatic successes in manufacturing, there is rising interest among companies in the pharmaceutical industry, which choose to implement LEAN in order to accomplish such goals as decreased wait time to release product to the market, reduce production waste, improve communication with end users and raise quality level both in the production and in testing laboratories. In this article, basics of LEAN and Six Sigma are presented and suggestion was given for application of their concepts in pharmaceutical industry together with harmonization with legal regulation represented by requirements Good Manufacturing Practice (cGMP, in order to work "smarter", more cost- effectively and avoid wasting time and other resources.

Lean in healthcare from employees' perspectives.

Science.gov (United States)

Drotz, Erik; Poksinska, Bozena

2014-01-01

The purpose of this paper is to contribute toward a deeper understanding of the new roles, responsibilities, and job characteristics of employees in Lean healthcare organizations. The paper is based on three cases studies of healthcare organizations that are regarded as successful examples of Lean applications in the healthcare context. Data were collected by methods including interviews, observations, and document studies. The implementation of Lean in healthcare settings has had a great influence on the roles, responsibilities, and job characteristics of the employees. The focus has shifted from healthcare professionals, where clinical autonomy and professional skills have been the guarding principles of patient care, to process improvement and teamwork. Different job characteristics may make it difficult to implement certain Lean practices in healthcare. Teamwork and decentralization of authority are examples of Lean practices that could be considered countercultural because of the strong professional culture and uneven power distribution, with doctors as the dominant decision makers. Teamwork, value flow orientation, and company-wide involvement in CI were associated with positive effects on the organizations' working environment, staff development, and organizational performance. In order to succeed with Lean healthcare, it is important to understand and recognize the differences in job characteristics between Lean manufacturing and healthcare. This paper provides insights into how Lean implementation changes the roles, responsibilities, and job characteristics of healthcare staff and the challenges and implications that may follow from this.

Children with burns referred for child abuse evaluation: Burn characteristics and co-existent injuries.

Science.gov (United States)

Pawlik, Marie-Christin; Kemp, Alison; Maguire, Sabine; Nuttall, Diane; Feldman, Kenneth W; Lindberg, Daniel M

2016-05-01

Intentional burns represent a serious form of physical abuse that must be identified to protect children from further harm. This study is a retrospectively planned secondary analysis of the Examining Siblings To Recognize Abuse (ExSTRA) network data. Our objective was to describe the characteristics of burns injuries in children referred to Child Abuse Pediatricians (CAPs) in relation to the perceived likelihood of abuse. We furthermore compare the extent of diagnostic investigations undertaken in children referred to CAPs for burn injuries with those referred for other reasons. Within this dataset, 7% (215/2890) of children had burns. Children with burns were older than children with other injuries (median age 20 months vs. 10 months). Physical abuse was perceived as likely in 40.9% (88) and unlikely in 59.1% (127). Scalds accounted for 52.6% (113) and contact burns for 27.6% (60). Several characteristics of the history and burn injury were associated with a significantly higher perceived likelihood of abuse, including children with reported inflicted injury, absent or inadequate explanation, hot water as agent, immersion scald, a bilateral/symmetric burn pattern, total body surface area ≥10%, full thickness burns, and co-existent injuries. The rates of diagnostic testing were significantly lower in children with burns than other injuries, yet the yield of skeletal survey and hepatic transaminases testing were comparable between the two groups. This would imply that children referred to CAPs for burns warrant the same level of comprehensive investigations as those referred for other reasons. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Lean and the quality of work

DEFF Research Database (Denmark)

Jensen, Per Langaa

2008-01-01

Lean has for the last decade developed as the dominating model for developing productions processes not only within industry but also in health care, administration and service industries in general. With this development a discussion on human factors aspects of lean has developed internationally....... Literature studies documents that it is not possible to establish a clear relation between lean and the psychosocial aspects of work. The studies also indicate that the context and the implementations process play a dominating role in how lean is experienced. This has been the basis for establishing...

Organizational change through Lean Thinking.

Science.gov (United States)

Tsasis, Peter; Bruce-Barrett, Cindy

2008-08-01

In production and manufacturing plants, Lean Thinking has been used to improve processes by eliminating waste and thus enhancing efficiency. In health care, Lean Thinking has emerged as a comprehensive approach towards improving processes embedded in the diagnostic, treatment and care activities of health-care organizations with cost containment results. This paper provides a case study example where Lean Thinking is not only used to improve efficiency and cost containment, but also as an approach to effective organizational change.

NASA GRC's High Pressure Burner Rig Facility and Materials Test Capabilities

Science.gov (United States)

Robinson, R. Craig

1999-01-01

The High Pressure Burner Rig (HPBR) at NASA Glenn Research Center is a high-velocity. pressurized combustion test rig used for high-temperature environmental durability studies of advanced materials and components. The facility burns jet fuel and air in controlled ratios, simulating combustion gas chemistries and temperatures that are realistic to those in gas turbine engines. In addition, the test section is capable of simulating the pressures and gas velocities representative of today's aircraft. The HPBR provides a relatively inexpensive. yet sophisticated means for researchers to study the high-temperature oxidation of advanced materials. The facility has the unique capability of operating under both fuel-lean and fuel-rich gas mixtures. using a fume incinerator to eliminate any harmful byproduct emissions (CO, H2S) of rich-burn operation. Test samples are easily accessible for ongoing inspection and documentation of weight change, thickness, cracking, and other metrics. Temperature measurement is available in the form of both thermocouples and optical pyrometery. and the facility is equipped with quartz windows for observation and video taping. Operating conditions include: (1) 1.0 kg/sec (2.0 lbm/sec) combustion and secondary cooling airflow capability: (2) Equivalence ratios of 0.5- 1.0 (lean) to 1.5-2.0 (rich), with typically 10% H2O vapor pressure: (3) Gas temperatures ranging 700-1650 C (1300-3000 F): (4) Test pressures ranging 4-12 atmospheres: (5) Gas flow velocities ranging 10-30 m/s (50-100) ft/sec.: and (6) Cyclic and steady-state exposure capabilities. The facility has historically been used to test coupon-size materials. including metals and ceramics. However complex-shaped components have also been tested including cylinders, airfoils, and film-cooled end walls. The facility has also been used to develop thin-film temperature measurement sensors.

Lean - set i et historisk perspektiv

DEFF Research Database (Denmark)

Michelsen, Aage U

2006-01-01

I kapitlet redegøres for, hvordan begrebet Lean opstod som en karakteristik af Toyota Production System (TPS), der igen har sin rod i scientific management. Gennem eksempler illustreres det, at centrale Lean-principper således har været anvendt i årtier. Der argumenteres for, at Lean i mange...

Modelling Lean and Green Supply Chain

Science.gov (United States)

Duarte, Susana Carla Vieira Lino Medina

The success of an organization depends on the effective control of its supply chain. It is important to recognize new opportunities for organization and its supply chain. In the last few years the approach to lean, agile, resilient and green supply chain paradigms has been addressed in the scientific literature. Research in this field shows that the integration of these concepts revealed some contradictions among so many paradigms. This thesis is mainly focused on the lean and green approaches. Thirteen different management frameworks, embodied in awards, standards and tools were studied to understand if they could contribute for the modelling process of a lean and green approach. The study reveals a number of categories that are common in most management frameworks, providing adequate conditions for a lean and green supply chain transformation. A conceptual framework for the evaluation of a lean and green organization`s supply chain was proposed. The framework considers six key criteria, namely, leadership, people, strategic planning, stakeholders, processes and results. It was proposed an assessment method considering a criteria score for each criterion. The purpose is to understand how lean and green supply chain can be compatible, using principles, practices, techniques or tools (i.e. elements) that support both, a lean and a green approach, in all key criteria. A case study in the automotive upstream supply chain was performed to understand more deeply if the elements proposed for the conceptual framework could be implemented in a real-scenario. Based on the conceptual framework and the case study, a roadmap to achieve a lean-green transformation is presented. The proposed roadmap revealed its contribution to the understanding on how and when an organization`s supply chain should apply the lean and green elements. This study is relevant to practice, as it may assist managers in the adoption of a lean and green supply chain approach, giving insights for the

Demonstration test on the safety of a cell ventilation system during a hypothetical explosive burning in a fuel reprocessing plant

International Nuclear Information System (INIS)

Suzuki, Motoe; Nishio, Gunji; Takada, Junichi; Tsukamoto, Michio; Koike, Tadao

1993-01-01

To demonstrate the safety of an air ventilation system of cells in a fuel reprocessing plant under a postulated explosive burning caused by solvent fire or by thermal decomposition of nitrated solvent, four types of demonstration tests have been conducted using a large-scale facility simulating a cell ventilation system of an actual reprocessing plant, thus revealing effective mitigation by cell and duct structures on the pressure and temperature pulses generated by explosive burning. In boilover burning tests, solvent fire in a model cell was observed with various sizes of burning surface area as a main parameter, and analysis was performed on the factors dominating the magnitude of boilover burning, revealing that the magnitude strongly depends on accumulated amounts and their ratio of oxygen and solvent vapor present in the cell. In deflagration tests, solid rocket fuel was burned in the cell to simulate the explosive source. The generated pressure and temperature pulses were effectively declined by the cell and duct structures and the integrity of the ventilation system was kept. In blower tests, a centrifugal turbo blower was imposed by a lump of air with a larger flow rate than the rated one by about six times to observe the transient response of the blower fan and motor. It was found that integrity of the blower was kept. In pressure transient tests, compressed air was blown into the cell to induce a mild transient state of fluid dynamics inside the facility, and a variety of data were successfully obtained to be used for the verification and improvement of a computer code. In all the tests, transient overloading of gas caused no damage on HEPA filters, and overloading on the blower motor was avoided either by the slipping of transmission belt or by the acceleration of blower fan rotation during peak flow. (author)

The Lean and Environment Toolkit

Science.gov (United States)

This Lean and Environment Toolkit assembles practical experience collected by the U.S. Environmental Protection Agency (EPA) and partner companies and organizations that have experience with coordinating Lean implementation and environmental management.

Lean og professionel autonomi på hospitaler

DEFF Research Database (Denmark)

Hasle, Peter

2014-01-01

Hospitaler står overfor store udfordringer fra voksende krav fra både patienter og samfund samtidig med begrænsede budgetter og stadig flere medicinske muligheder. Hospitalsledelserne anvender lean som en af de væsentligste metoder til at løse disse udfordringer. Lean stammer imidlertid fra...... industrien, og det er spørgsmålet, hvordan lean bliver tilpasset i til en hospitalssammenhæng, og hvilke konsekvenser lean får for medarbejderne. Dette spørgsmål er undersøgt i forbindelse med introduktion af lean i en kræftafdeling på et universitetshospital. Det viste sig vanskeligere end forventet...... at implementere lean, og konsekvenserne for henholdsvis laboranter og sygeplejersker viste sig at være meget forskelligartede. Laboranterne oplevede et forbedret arbejdsmiljø, mens det modsatte var tilfældet for sygeplejerskerne. En mulig forklaring er, at lean øgede kontrollen over eget arbejde for laboranterne...

Clinical and Metabolic Characterization of Lean Caucasian Subjects With Non-alcoholic Fatty Liver.

Science.gov (United States)

Feldman, Alexandra; Eder, Sebastian K; Felder, Thomas K; Kedenko, Lyudmyla; Paulweber, Bernhard; Stadlmayr, Andreas; Huber-Schönauer, Ursula; Niederseer, David; Stickel, Felix; Auer, Simon; Haschke-Becher, Elisabeth; Patsch, Wolfgang; Datz, Christian; Aigner, Elmar

2017-01-01

Non-alcoholic fatty liver disease (NAFLD) is closely linked to obesity; however, 5-8% of lean subjects also have evidence of NAFLD. We aimed to investigate clinical, genetic, metabolic and lifestyle characteristics in lean Caucasian subjects with NAFLD. Data from 187 subjects allocated to one of the three groups according to body mass index (BMI) and hepatic steatosis on ultrasound were obtained: lean healthy (BMI≤25 kg/m 2 , no steatosis, N=71), lean NAFLD (BMI≤25 kg/m 2 , steatosis, N=55), obese NAFLD (BMI≥30 kg/m 2 , steatosis; N=61). All subjects received a detailed clinical and laboratory examination including oral glucose tolerance test. The serum metabolome was assessed using the Metabolomics AbsoluteIDQ p180 kit (BIOCRATES Life Sciences). Genotyping for single-nucleotide polymorphisms (SNPs) associated with NAFLD was performed. Lean NAFLD subjects had fasting insulin concentrations similar to lean healthy subjects but had markedly impaired glucose tolerance. Lean NAFLD subjects had a higher rate of the mutant PNPLA3 CG/GG variant compared to lean controls (P=0.007). Serum adiponectin concentrations were decreased in both NAFLD groups compared to controls (Pphosphatidylcholines (PCaa C36:3; false discovery rate (FDR)-corrected P-value<0.001) as well as lysine, tyrosine, and valine (FDR<0.001). Lean subjects with evidence of NAFLD have clinically relevant impaired glucose tolerance, low adiponectin concentrations and a distinct metabolite profile with an increased rate of PNPLA3 risk allele carriage.

A Survey of Studies on Ignition and Burn of Inertially Confined Fuels

Science.gov (United States)

Atzeni, Stefano

2016-10-01

A survey of studies on ignition and burn of inertial fusion fuels is presented. Potentials and issues of different approaches to ignition (central ignition, fast ignition, volume ignition) are addressed by means of simple models and numerical simulations. Both equimolar DT and T-lean mixtures are considered. Crucial issues concerning hot spot formation (implosion symmetry for central ignition; igniting pulse parameters for fast ignition) are briefly discussed. Recent results concerning the scaling of the ignition energy with the implosion velocity and constrained gain curves are also summarized.

Lean automation development : applying lean principles to the automation development process

OpenAIRE

Granlund, Anna; Wiktorsson, Magnus; Grahn, Sten; Friedler, Niklas

2014-01-01

By a broad empirical study it is indicated that automation development show potential of improvement. In the paper, 13 lean product development principles are contrasted to the automation development process and it is suggested why and how these principles can facilitate, support and improve the automation development process. The paper summarises a description of what characterises a lean automation development process and what consequences it entails. Main differences compared to current pr...

Effects of burn location and investigator on burn depth in a porcine model.

Science.gov (United States)

Singer, Adam J; Toussaint, Jimmy; Chung, Won Taek; Thode, Henry C; McClain, Steve; Raut, Vivek

2016-02-01

In order to be useful, animal models should be reproducible and consistent regardless of sampling bias, investigator creating burn, and burn location. We determined the variability in burn depth based on biopsy location, burn location and investigator in a porcine model of partial thickness burns. 24 partial thickness burns (2.5 cm by 2.5 cm each) were created on the backs of 2 anesthetized pigs by 2 investigators (one experienced, one inexperienced) using a previously validated model. In one of the pigs, the necrotic epidermis covering each burn was removed. Five full thickness 4mm punch biopsies were obtained 1h after injury from the four corners and center of the burns and stained with Hematoxylin and Eosin and Masson's trichrome for determination of burn depth by a board certified dermatopathologist blinded to burn location and investigator. Comparisons of burn depth by biopsy location, burn location and investigator were performed with t-tests and ANOVA as appropriate. The mean (SD) depth of injury to blood vessels (the main determinant of burn progression) in debrided and non-debrided pigs pooled together was 1.8 (0.3)mm, which included 75% of the dermal depth. Non-debrided burns were 0.24 mm deeper than debrided burns (Plocations, in debrided burns. Additionally, there were also no statistical differences in burn depths from midline to lateral in either of these burn types. Burn depth was similar for both investigators and among biopsy locations. Burn depth was greater for caudal locations in non-debrided burns and overall non-debrided burns were deeper than debrided burns. However, burn depth did not differ based on investigator, biopsy site, and medial-lateral location. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Epidemiology, etiology and outcomes of burn patients in a Referral Burn Hospital, Tehran

Directory of Open Access Journals (Sweden)

Mohammad Mehdi Soltan Dallal

2016-08-01

Full Text Available Background: Burns and its complications are regarded as a major problem in the society. Skin injuries resulted from ultraviolet radiation, radioactivity, electricity or chemicals as well as respiratory damage from smoke inhalation are considered burns. This study aimed to determine the epidemiology and outcome of burn patients admitted to Motahari Hospital, Tehran, Iran. Methods: Two hundred patients with second-degree burns admitted to Motahari Referral Center of Burn in Tehran, Iran. They were studied during a period of 12 months from May 2012 to May 2013. During the first week of treatment swabs were collected from the burn wounds after cleaning the site with sterile normal saline. Samples were inoculated in blood agar and McConkey agar, then incubation at 37 C for 48 hours. Identification was carried out according to standard conventional biochemical tests. Treatment continued up to epithelial formation and wound healing. Results of microbial culture for each patient was recorded. Healing time of the burn wounds in patients was recorded in log books. Chi-square test and SPSS Software v.19 (IBM, NY, USA were used for data analysis. Results: Our findings indicate that the most causes of burns are hot liquids in 57% of cases and flammable liquid in 21% of cases. The most cases of burns were found to be in the range of 21 to 30 percent with 17.5% and 7% in male and female respectively. Gram-negative bacteria were dominated in 85.7% and among them pseudomonas spp. with 37.5% were the most common cause of infected burns, followed by Enterobacter, Escherichia coli, Staphylococcus aureus, Acinetobacter and Klebsiella spp. Conclusion: The results of this study showed that the most cause of burns in both sex is hot liquid. Men were more expose to burn than women and this might be due to the fact that men are involved in more dangerous jobs than female. Pseudomonas aeruginosa was the most common organism encountered in burn infection.

Comparative study of lean practices between Japanese and Malaysia automotive service centres

Science.gov (United States)

Ahmad, Md Fauzi; Ting, Neo Yeong; Nor, Nik Hisyamudin Muhd; Wei, Chan Shiau; Hassan, Mohd Fahrul; Hamid, Nor Aziati Abdul

2017-10-01

Nowadays, lean practices are implemented in many manufacturing and services companies. Lean practices are implemented in order to minimize wastes while maximise the overall performances in an organisation. In service sector, lean practices are importance to ensure value added services can be delivered to customers. However, Malaysia automotive companies cannot compete with Japanese automotive companies in terms of their customer satisfaction. The purpose of this study is to compare the lean practice between Japanese and Malaysia automotive service centres. A total of 80 questionnaires out of 100 distributed questionnaires were responded and this represented as 80% of response rate. The Mann-Whitney test result shows that there were four out of five factors of lean practices have significant differences between Japanese and Malaysia automotive service centres, which are TPM, JIT, Kanban, and 5S. VSM has not significant difference between ownerships. In addition, TPM, JIT, Kanban, VSM and 5S were higher practices in Japanese companies against Malaysia companies. Many Malaysia companies are still in the journey of lean practices and they need recommendation guidance to compete with other long-term established companies. Based on the survey result, the significant differences are identified as weak points of Malaysia companies as an opportunity to improve. Moreover, the significance of this study can help researchers and industry players to improve lean practices in automotive service industry.

Lean mass and insulin resistance in women with polycystic ovary syndrome.

Science.gov (United States)

Comerford, Kevin B; Almario, Rogelio U; Kim, Kyoungmi; Karakas, Sidika E

2012-09-01

Insulin resistance is common in women with polycystic ovary syndrome (PCOS). Muscle is the major tissue utilizing glucose while excess adipose tissue relates to insulin resistance. Thus, body composition is likely to be an important regulator of insulin sensitivity. Thirty-nine PCOS patients (age: 29.9±1.0 years; BMI: 33.8±1.2 kg/m(2)) participated in a cross sectional study. Body composition was measured by dual energy x-ray absorptiometry (DEXA). Insulin resistance and secretion were assessed using oral glucose tolerance test (OGTT) and frequently sampled intravenous glucose tolerance test (FS-IVGTT). In contrast with the conventional expectations, lean mass correlated directly (Plean mass (52.8±1.8 vs 44.4±1.6 kg), those with higher lean mass had a higher glucose response during OGTT (AUC(Glucose); P=.034). In contrast, 17 pairs matched for lean mass (48.7±1.7 and 48.9±1.6 kg) but discordant for fat mass (43.3±2.6 vs 30.3±8.9 kg) showed no differences in insulin resistance parameters. These novel findings indicate that lean mass relates directly to insulin resistance in PCOS. Published by Elsevier Inc.

Barents Sea field test of herder to thicken oil for in-situ burning in drift ice

International Nuclear Information System (INIS)

Buist, I.; Potter, S.; Sorstrom, S.E.

2009-01-01

Thick oil slicks are the key to effective in situ burning. Pack ice can enable in situ burning by keeping slicks thick. Oil spills in drift ice conditions can rapidly spread and become too thin to ignite. The application of chemical surface-active agents known as oil herders are commonly used in open waters to clean and contain oil slicks. Herders result in the formation of a monolayer of surfactants on the water surface and reduce the surface tension on the surrounding water considerably. When the surfactant monolayer reaches the edge of a thin oil slick, it changes the balance of interfacial forces acting on the slick edge and allows the interfacial tensions to contract the oil into thicker layers. This study examined the use of chemical herding agents to thicken oil spills in broken ice to allow them to be ignited and burned in situ. Two meso-scale field burn tests were conducted in May 2008 with crude oil slicks of about 0.1 and 0.7 m 3 in open drift ice off Svalbard in the Barents Sea. Prior to the field experiments, 2 series of small laboratory tests were conducted using Heidrun and Statfjord crudes to determine the ability of the U.S. Navy herding agent to contract slicks of the oil. In the first field experiment involving 102 litres of fresh Heidrun, the slick was unexpectedly carried by currents to a nearby ice edge where the oil was ignited and burned. Approximately 80 per cent of the oil was consumed in the burn. In the second field experiment involving 630 litres of fresh Heidrun, the free-drifting oil was allowed to spread for 15 minutes until it was much too thin to ignite. When the herding agent was applied, the slick contracted and thickened for about 10 minutes and was then ignited using a gelled gas igniter. A 9-minute long burn consumed about 90 per cent of the oil. 9 refs., 5 tabs., 34 figs.

The Development Of A Theoretical Lean Culture Causal Framework To Support The Effective Implementation Of Lean In Automotive Component Manufacturers

Directory of Open Access Journals (Sweden)

Van der Merwe, Karl Robert

2014-05-01

Full Text Available Although it is generally accepted that lean manufacturing improves operational performance, many organisations are struggling to adapt to the lean philosophy. The purpose of this study is to contribute to a more effective strategy for implementing the lean manufacturing improvement philosophy. The study sets out both to integrate well-researched findings and theories related to generic organisational culture with more recent research and experience related to lean culture, and to examine the role that culture plays in the effective implementation of lean manufacturing principles and techniques. The ultimate aim of this exercise is to develop a theoretical lean culture causal framework.

Prevalence and hemodynamic effects of leaning during CPR

Science.gov (United States)

Niles, Dana E.; Sutton, Robert M.; Nadkarni, Vinay M.; Glatz, Andrew; Zuercher, Mathias; Maltese, Matthew R.; Eilevstjønn, Joar; Abella, Benjamin S.; Becker, Lance B.; Berg, Robert A.

2013-01-01

Background Cardiopulmonary resuscitation (CPR) guidelines recommend complete release between chest compressions (CC). Objective Evaluate the hemodynamic effects of leaning (incomplete chest wall release) during CPR and the prevalence of leaning during CPR. Results In piglet ventricular fibrillation cardiac arrests, 10% and 20% (1.8 kg and 3.6 kg, respectively), leaning during CPR increased right atrial pressures, decreased coronary perfusion pressures, and decreased cardiac index and left ventricular myocardial blood flow by nearly 50%. In contrast, residual leaning of a 260 g accelerometer/ force feedback device did not adversely affect cardiac index or myocardial blood flow. Among 108 adult in-hospital CPR events, leaning ≥2.5 kg was demonstrable in 91% of the events and 12% of the evaluated CC. For 12 children with in-hospital CPR, 28% of CC had residual leaning ≥2.5 kg and 89% had residual leaning ≥0.5 kg. Conclusions Leaning during CPR increases intrathoracic pressure, decreases coronary perfusion pressure, and decreases cardiac output and myocardial blood flow. Leaning is common during CPR. PMID:22208173

Lean Transformation Guidance: Why Organizations Fail To Achieve and Sustain Excellence Through Lean Improvement

Directory of Open Access Journals (Sweden)

Mohammed Hamed Ahmed

2013-06-01

Full Text Available Many companies are complaining that lean didn’t achieve their long-term goals, and the improvement impact was very short-lived. 7 out of each 10 lean projects fail as companies try to use lean like a toolkit, copying and pasting the techniques without trying to adapt the employee’s culture, manage the improvement process, sustain the results, and develop their leaders. When the Toyota production system was created, the main goal was to remove wastes from the shop floor using some lean techniques and tools. What was not clear is that this required from Toyota a long process of leadership development, and a high commitment to training and coaching their employee. A Failure to achieve and sustain the improvement is a problem of both management and leadership as well as the improper understanding of the human behavior, and the required culture to success.

Lean management in a non-manufacturing organization

Directory of Open Access Journals (Sweden)

Mladen Žvorc

2013-12-01

Full Text Available This paper examines the possibilities of a lean approach to non-manufacturing functions, i.e. a market-oriented organization. This refers to purchasing, shipment, storage, sale and delivery of goods; marketing, etc. A lean approach to business operations is discussed and several lean business methods are developed on the basis of which lean management can be used not only in manufacturing, but also in non-manufacturing organizations.

Lean in Air Permitting Guide

Science.gov (United States)

The Lean in Air Permitting Guide is designed to help air program managers at public agencies better understand the potential value and results that can be achieved by applying Lean improvement methods to air permitting processes.

Lean-Prinzipien für verbesserte Kosteneffizienz: Instandhaltungseffizienz durch Lean Maintenance

OpenAIRE

Bandow, G.; Schmidt, A.

2008-01-01

Die Bedeutung der Instandhaltung nimmt weiter zu. In einem Lean Umfeld mit einer immer verschwendungsärmeren Produktion stehen nicht nur die Kosteneffizienz und Verfügbarkeit der Produktionsmittel im Fokus. Unplanmäßige Stillstände kosten Geld und gefährden häufig auch Personal und Produkt. Lean Maintenance vermeidet Verschwendung und optimiert so die Effektivität und Effizienz der Instandhaltung. Das zielgerichtete Zusammenspiel von Menschen, Prozessen und Technik garantiert dabei den Erfolg...

TH-C-9A-01: Lean Tools and Methods

International Nuclear Information System (INIS)

Rangaraj, D; Chan, K; Boddu, S; Pawlicki, T; Dieterich, S

2014-01-01

Lean thinking has revolutionized the manufacturing industry. Toyota has pioneered and leveraged this aspect of Lean thinking. Application of Lean thinking and Lean Six Sigma techniques into Healthcare and in particular in Radiation Oncology has its merits and challenges. To improve quality, safety and patient satisfaction with available resources or reducing cost in terms of time, staff and resources is demands of today's healthcare. Radiation oncology treatment involves many processes and steps, identifying and removing the non-value added steps in a process can significantly improve the efficiency. Real projects undertaken in radiation oncology department in cutting down the procedure time for MRI guided brachytherapy to 40% less using lean thinking will be narrated. Simple Lean tools and techniques such as Gemba walk, visual control, daily huddles, standard work, value stream mapping, error-proofing, etc. can be applied with existing resources and how that improved the operation in a Radiation Oncology department's two year experience will be discussed. Lean thinking focuses on identifying and solving the root-cause of a problem by asking “Why” and not “Who” and this requires a culture change of no blame. Role of leadership in building lean culture, employee empowerment and trains and develops lean thinkers will be presented. Why Lean initiatives fail and how to implement lean successfully in your clinic will be discussed. Learning Objectives: Concepts of lean management or lean thinking. Lean tools and techniques applied in Radiation Oncology. Implement no blame culture and focus on system and processes. Leadership role in implementing lean culture. Challenges for Lean thinking in healthcare

TH-C-9A-01: Lean Tools and Methods

Energy Technology Data Exchange (ETDEWEB)

Rangaraj, D [Baylor Scott and White Health, Temple, TX (United States); Chan, K [Princess Margaret Hospital, Toronto (Canada); Boddu, S [Temple, TX (United States); Pawlicki, T [UC San Diego, La Jolla, CA (United States); Dieterich, S [UC Davis Medical Center, Sacramento, CA (United States)

2014-06-15

Lean thinking has revolutionized the manufacturing industry. Toyota has pioneered and leveraged this aspect of Lean thinking. Application of Lean thinking and Lean Six Sigma techniques into Healthcare and in particular in Radiation Oncology has its merits and challenges. To improve quality, safety and patient satisfaction with available resources or reducing cost in terms of time, staff and resources is demands of today's healthcare. Radiation oncology treatment involves many processes and steps, identifying and removing the non-value added steps in a process can significantly improve the efficiency. Real projects undertaken in radiation oncology department in cutting down the procedure time for MRI guided brachytherapy to 40% less using lean thinking will be narrated. Simple Lean tools and techniques such as Gemba walk, visual control, daily huddles, standard work, value stream mapping, error-proofing, etc. can be applied with existing resources and how that improved the operation in a Radiation Oncology department's two year experience will be discussed. Lean thinking focuses on identifying and solving the root-cause of a problem by asking “Why” and not “Who” and this requires a culture change of no blame. Role of leadership in building lean culture, employee empowerment and trains and develops lean thinkers will be presented. Why Lean initiatives fail and how to implement lean successfully in your clinic will be discussed. Learning Objectives: Concepts of lean management or lean thinking. Lean tools and techniques applied in Radiation Oncology. Implement no blame culture and focus on system and processes. Leadership role in implementing lean culture. Challenges for Lean thinking in healthcare.

Rethinking Lean Service

Science.gov (United States)

Seddon, John; O'Donovan, Brendan; Zokaei, Keivan

Ever since Levitt's influential Harvard Business Review article 'Production-Line Approach to Service' was published in 1972, it has been common for services to be treated like production lines in both the academic literature and more widely in management practice. The belief that achieving economies of scale will reduce unit costs is a common feature of management decision-making. As technological advancement has produced ever more sophisticated IT and telephony, it has become increasingly easier for firms to standardise and off-shore services. The development of the 'lean' literature has only helped to emphasise the same underlying management assumptions: by managing cost and workers' activity, organisational performance is expected to improve. This chapter argues that through misinterpretation of the core paradigm 'lean' has become subsumed into the 'business as usual' of conventional service management. As a result, 'lean' has become synonymous with 'process efficiency' and the opportunity for significant performance improvement - as exemplified by Toyota - has been missed.

Lean consumption.

Science.gov (United States)

Womack, James P; Jones, Daniel T

2005-03-01

During the past 20 years, the real price of most consumer goods has fallen worldwide, the variety of goods and the range of sales channels offering them have continued to grow, and product quality has steadily improved. So why is consumption often so frustrating? It doesn't have to be--and shouldn't be--the authors say. They argue that it's time to apply lean thinking to the processes of consumption--to give consumers the full value they want from goods and services with the greatest efficiency and the least pain. Companies may think they save time and money by off-loading work to the consumer but, in fact, the opposite is true. By streamlining their systems for providing goods and services, and by making it easier for customers to buy and use those products and services, a growing number of companies are actually lowering costs while saving everyone time. In the process, these businesses are learning more about their customers, strengthening consumer loyalty, and attracting new customers who are defecting from less user-friendly competitors. The challenge lies with the retailers, service providers, manufacturers, and suppliers that are not used to looking at total cost from the standpoint of the consumer and even less accustomed to working with customers to optimize the consumption process. Lean consumption requires a fundamental shift in the way companies think about the relationship between provision and consumption, and the role their customers play in these processes. It also requires consumers to change the nature of their relationships with the companies they patronize. Lean production has clearly triumphed over similar obstacles in recent years to become the dominant global manufacturing model. Lean consumption, its logical companion, can't be far behind.

Fetuin-A levels in lean and obese women with polycystic ovary syndrome.

Science.gov (United States)

Kozakowski, Jarosław; Jeske, Wojciech; Zgliczyński, Wojciech

2014-01-01

The aim of this study was to estimate serum fetuin-A levels in lean and obese women with polycystic ovary syndrome (PCOS) and to find possible relationships between fetuin-A, metabolic factors and androgens in these patients. In 25 lean (18-38 years, BMI 17.5-25.0 kg/m2) and 15 obese women (20-41 years, BMI 28.1-53.2 kg/m2) with PCOS, anthropometric indices and body composition were measured. Fasting serum fetuin-A, adiponectin, leptin, glucose, lipids, hsCRP, insulin, androgens and SHGB levels were estimated. There was no significant difference in serum fetuin-A levels between lean and obese patients: 0.54 ± 0.13 g/L and 0.60 ± 0.14 g/L, respectively. We noted a correlation between BMI and leptin levels (r = 0.88; p lean patients, we found a correlation between fetuin-A levels and ALT activity (r = 0.44; p lean and obese women with PCOS. We found an association between fetuin-A levels and ALT activity in lean patients and between fetuin-A levels and DHEA-S in all women. The role of fetuin-A in the mechanisms of insulin resistance, and its potential impact on androgenic hormones production in women with PCOS, need to be tested in further studies.

Lean in the supply chain : research and practice

OpenAIRE

Ugochukwu, Paschal

2012-01-01

Lean is a management philosophy that enhances customer value through waste elimination and continuous improvement in a system by applying lean principles, practices, and techniques. The focus on lean implementations and research had been typically a single company without extension to the entire supply chain. When the concept of lean is implemented across the entire supply chain, however, it is referred to as lean supply chain. The purpose of this thesis is to create a structure from theory a...

Lean Six Sigma in financial services

OpenAIRE

de Koning, H.; Does, R.J.M.M.; Bisgaard, S.

2008-01-01

Lean Thinking and Six Sigma are typically considered as separate approaches to process innovation, with complementary strengths. When combined as Lean Six Sigma, this approach provides a unified framework for systematically developing innovations. Lean Six Sigma can also bring about significant results and breakthrough improvements in financial services, as demonstrated with four case studies from Dutch multinational insurance companies. These cases demonstrate the importance of incremental i...

Lean and psychosocial work environment in manufacturing

DEFF Research Database (Denmark)

Edwards, Kasper; Thye, Nina; Nielsen, Anders P.

2011-01-01

Lean is currently the rationalization method of choice in the Danish manufacturing industry. This paper reports finding from three lean implementation cases. All cases are manufacturing companies focusing on upmarket products produced in small series. Prior to lean production was organized as sel...

A Sand Cone Model of Lean Implementation

OpenAIRE

Yestemessov, Azamat

2011-01-01

Over the past 20 years Lean Production system has been a focus of researches by different academicians. A numerous works have been written in the field of Lean implementation in manufacturing companies. However, as shown, most of the academic topics relate to the issues of implementing Lean tools and techniques. Critical Success Factors have been also described widely; however, no efforts in systematization have been made. Only several works have a focus on integration of Lean implementation ...

Lean in healthcare: the unfilled promise?

Science.gov (United States)

Radnor, Zoe J; Holweg, Matthias; Waring, Justin

2012-02-01

In an effort to improve operational efficiency, healthcare services around the world have adopted process improvement methodologies from the manufacturing sector, such as Lean Production. In this paper we report on four multi-level case studies of the implementation of Lean in the English NHS. Our results show that this generally involves the application of specific Lean 'tools', such as 'kaizen blitz' and 'rapid improvement events', which tend to produce small-scale and localised productivity gains. Although this suggests that Lean might not currently deliver the efficiency improvements desired in policy, the evolution of Lean in the manufacturing sector also reveals this initial focus on the 'tool level'. In moving to a more system-wide approach, however, we identify significant contextual differences between healthcare and manufacturing that result in two critical breaches of the assumptions behind Lean. First, the customer and commissioner in the private sector are the one and the same, which is essential in determining 'customer value' that drives process improvement activities. Second, healthcare is predominantly designed to be capacity-led, and hence there is limited ability to influence demand or make full use of freed-up resources. What is different about this research is that these breaches can be regarded as not being primarily 'professional' in origin but actually more 'organisational' and 'managerial' and, if not addressed could severely constrain Lean's impact on healthcare productivity at the systems level. Copyright © 2011 Elsevier Ltd. All rights reserved.

Transferring lean management infrastructure for increasing productivity

Directory of Open Access Journals (Sweden)

Ph.D.Daniel Georgescu

2010-12-01

Full Text Available These years, manufacturing function have been transferred rapidly and globally from matured countries to emerging countries. In this paper is about the critical elements for successful transfer of lean management among sites and countries. Based on this general descriptive analysis, current global transfer activity of Lean as well as its future direction is also described. According to the gradual progress of lean management transfer, necessity of its refinement/reinforcement is recognized and some research subjects are proposed for contributing further encouragement of its global activities. In this paper, based on this understanding, requisites for transfer of lean management are discussed through investigating global activity of Lean and specification of infrastructure enabling its smooth transfer is examined

How the Lean Management System is Working on a Closure Project - 13242

Energy Technology Data Exchange (ETDEWEB)

Mowery, Carol [Washington Closure Hanford, 2620 Fermi, Richland, Washington, 99354 (United States)

2013-07-01

Washington Closure Hanford, LLC (WCH) manages the River Corridor Closure Project (RCCP), a 10-year contract, in which WCH will clean up 220 mi{sup 2} of contaminated land at the Hanford Site in Richland, Washington. Strategic planning sessions in 2009 identified key performance areas that were essential to closure and in which focused change could result in dramatic performance improvement. Lean Management Systems (Lean) was selected as the methodology to achieve the desired results. The Lean Process is built upon the fundamentals of the power of respect for people and the practice of continuous process improvement. Lean uses week-long, focused sessions that teach a selected team the techniques to recognize waste within their own work processes, propose potential solutions, and then conduct experiments during the week to test their solutions. In 2011, the Lean process was implemented in the Waste Operations organization. From there it was expanded to closure documents, field remediation, and decommissioning and demolition. WCH identified the following Lean focus areas: 1) closure document processes that required extensive internal preparation, and lengthy external review and approval cycles; 2) allocation of limited transportation and waste disposal resources to meet aggressive remediation schedules; 3) effective start-of-the-day routines in field operations; 4) improved excavation and load-out processes; and 5) approaches to strengthen safety culture and support disciplined operations. Since the introduction of Lean, RCCP has realized many successes and also gained some unexpected benefits. (authors)

How the Lean Management System is Working on a Closure Project - 13242

International Nuclear Information System (INIS)

Mowery, Carol

2013-01-01

Washington Closure Hanford, LLC (WCH) manages the River Corridor Closure Project (RCCP), a 10-year contract, in which WCH will clean up 220 mi 2 of contaminated land at the Hanford Site in Richland, Washington. Strategic planning sessions in 2009 identified key performance areas that were essential to closure and in which focused change could result in dramatic performance improvement. Lean Management Systems (Lean) was selected as the methodology to achieve the desired results. The Lean Process is built upon the fundamentals of the power of respect for people and the practice of continuous process improvement. Lean uses week-long, focused sessions that teach a selected team the techniques to recognize waste within their own work processes, propose potential solutions, and then conduct experiments during the week to test their solutions. In 2011, the Lean process was implemented in the Waste Operations organization. From there it was expanded to closure documents, field remediation, and decommissioning and demolition. WCH identified the following Lean focus areas: 1) closure document processes that required extensive internal preparation, and lengthy external review and approval cycles; 2) allocation of limited transportation and waste disposal resources to meet aggressive remediation schedules; 3) effective start-of-the-day routines in field operations; 4) improved excavation and load-out processes; and 5) approaches to strengthen safety culture and support disciplined operations. Since the introduction of Lean, RCCP has realized many successes and also gained some unexpected benefits. (authors)

Lean Implementation : the significance of people and dualism

OpenAIRE

Bengt, Halling

2013-01-01

Lean, with its origins at the Toyota Motor Company, is a concept that is known to increase effectiveness in manufacturing. The Lean concept is now argued to be relevant not only in manufacturing but in service and health-care delivery as well. The reported results of Lean implementation efforts are divided. There are reports that most of the Lean implementation efforts are not reaching the goal; on the other hand, there are reports of promising results. The divided results from Lean implement...

Lean Six Sigma implementation and organizational culture.

Science.gov (United States)

Knapp, Susan

2015-01-01

The purpose of this paper is to examine the relationship between four organizational cultural types defined by the Competing Values Framework and three Lean Six Sigma implementation components - management involvement, use of Lean Six Sigma methods and Lean Six Sigma infrastructure. The study involved surveying 446 human resource and quality managers from 223 hospitals located in Maine, New Hampshire, Vermont, Massachusetts and Rhode Island using the Organizational Culture Assessment Instrument. Findings - In total, 104 completed responses were received and analyzed using multivariate analysis of variance. Follow-up analysis of variances showed management support was significant, F(3, 100)=4.89, p cultures having significant interactions with management support. The relationship between organizational culture and Lean Six Sigma in hospitals provides information on how specific cultural characteristics impact the Lean Six Sigma initiative key components. This information assists hospital staff who are considering implementing quality initiatives by providing an understanding of what cultural values correspond to effective Lean Six Sigma implementation. Managers understanding the quality initiative cultural underpinnings, are attentive to the culture-shared values and norm's influence can utilize strategies to better implement Lean Six Sigma.

Lean thinking for a maintenance process

Directory of Open Access Journals (Sweden)

Sherif Mostafa

2015-01-01

Full Text Available The maintenance process shares significant operating costs in an organisation. Lean thinking can be incorporated into maintenance activities through applying its principles and practices/tools. Lean maintenance (LM is a prerequisite for lean manufacturing systems. This research proposes a new structure for LM process based on a systematic literature review of a significant number of related articles that were published on LM. The process structure is designed based on the five lean principles to guide and support organisations to pursue maintenance excellence. This study establishes a scheme for LM tools that are structured into 2 level 4 bundles and 26 lean practices/tools and develops a House of Waste (HoW to demonstrate the association between maintenance wastes and the LM tools. With a successful accomplishment of the proposed scheme, the performance of a maintenance department can create more improvement opportunities over time to reach the maintenance excellence status.

THE LEAN AND SIX SIGMA SINERGY

Directory of Open Access Journals (Sweden)

Mirko Sokovic

2008-12-01

Full Text Available Many organizations, dealing with continuous improvement methods, have realized that Lean and Six Sigma methodologies complement each other. Lean manufacturing focuses on the remova l of waste so that all processes in the total system add value from the customers' perspectives. The main emphasis of Six Sigma is the application of statistical tools in a disciplined manner, which requires data-driven decision-making. The integration of Lean and Six Sigma provides a synergetic effect, a rapid process improvement strategy for attaining organizational goals. When separated, Lean manufacturing cannot bring a process under statistical control, and Six Sigma cannot dramatically improve cycle time or reduce invested capital. Together, synergistic qualities are created to maximize the potential for a process improvement. The paper deals with Lean and Six Sigma principles and approaches used in modern manufacturing for process improvements, and bring forward benefits that are gained when these two methodologies are integrated.

Performance Improvement through Implementation of Lean Maintenance

OpenAIRE

S. Kolanjiappan; Dr. K. Maran

2011-01-01

Lean Maintenance is a relatively new term, invented in the last decade of the twentieth century, but the principles are well established in Total Productive Maintenance (TPM). Lean Maintenance—taking its lead from Lean Manufacturing—applies some new techniques to TPM concepts to render a more structured implementation path. Tracing its roots back to Henry Ford with modern refinements born in Japanese manufacturing, specifically the Toyota Production System (TPS). Lean seeks to eliminate a...

Safety reloaded: lean operations and high involvement work practices for sustainable workplaces

OpenAIRE

Camuffo, Arnaldo; De Stefano, Federica; Paolino, Chiara

2017-01-01

Starting from the recent quest to investigate the human side of organizational sustainability, this study applies a variety of regression analyses to investigate the effects of Lean Operations, High Involvement Work Practices, and management behaviors on occupational safety. It tests and finds support for the hypotheses that Lean Production systems, High Involvement Work Practices, and two specific management behaviors—workers’ capability development (coaching and teaching of workers) and emp...

Process Cycle Efficiency Improvement Through Lean: A Case Study

Directory of Open Access Journals (Sweden)

P.V. Mohanram

2011-06-01

Full Text Available Lean manufacturing is an applied methodology of scientific, objective techniques that cause work tasks in a process to be performed with a minimum of non-value adding activities resulting in greatly reduced wait time, queue time, move time, administrative time, and other delays. This work addresses the implementation of lean principles in a construction equipment company. The prime objective is to evolve and test several strategies to eliminate waste on the shop floor. This paper describes an application of value stream mapping (VSM. Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. A noticeable reduction in cycle time and increase in cycle efficiency is confirmed. The production flow was optimized thus minimizing several non-value added activities/times such as bottlenecking time, waiting time, material handling time, etc. This case study can be useful in developing a more generic approach to design lean environment.

Lean in healthcare: A comprehensive review.

Science.gov (United States)

D'Andreamatteo, Antonio; Ianni, Luca; Lega, Federico; Sargiacomo, Massimo

2015-09-01

Lean seems to be the next revolution for a better, improved, value-based healhcare. In the last 15 years Lean has been increasingly adapted and adopted in healthcare. Accordingly, Lean healthcare has been developing into a major strand of research since the early 2000s. The aim of this work is to present a comprehensive overview of the main issues highlighted by research on implementation of Lean in a complex contest such as the healthcare one. Comprehensive literature review was conducted in order to identify empirical and theoretical articles published up to September 2013. Thematic analysis was performed in order to extract and synthesis data. 243 articles were selected for analysis. Lean is best understood as a means to increase productivity. Hospital is the more explored setting, with emergency and surgery as the pioneer departments. USA appears to be the leading country for number of applications. The theoretical works have been focused mainly on barriers, challenges and success factors. Sustainability, framework for measurement and critical appraisal remain underestimated themes. Evaluations of "system wide approach" are still low in number. Even though Lean results appear to be promising, findings so far do not allow to draw a final word on its positive impacts or challenges when introduced in the healthcare sector. Scholars are called to explore further the potentiality and the weaknesses of Lean, above all as for the magnitude of investments required and for the engagement of the whole organization it represents increasingly strategic choice, whilst health professionals, managers and policy makers could and should learn from research how to play a pivotal role for a more effective implementation of lean in different health contexts. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Développement d'un moteur 4-soupapes fonctionnant en mélange dilué. Une nouvelle approche basée sur l'optimisation de l'aérodynamique interne Application of Flow Field Optimization to Lean Burn Engine Development. A New Approach Based on Internal Flow Field Optimization

Directory of Open Access Journals (Sweden)

Henriot S.

2006-11-01

entre 0,60 et 0,70 suivant la charge et le régime. La diminution des émissions d'oxydes d'azote qui en résulte atteint en moyenne sur des points représentatifs du cycle ECE15 74 % par rapport au fonctionnement à la stoechiométrie. Enfin, des essais avec recyclage des gaz d'échappement ont démontré le potentiel de la solution optimisée d'un point de vue aérodynamique à tout mode de fonctionnement en mélange dilué. The constraints that must be accounted for inbuilding a new engine are increasing. It is necessary to contend with user demands for performance, while improving efficiency, limiting pollutant emissions and reducing knock sensitivity. Given the number of parameters to be taken into account, the response to these demands would require large investments in time and resources if conventional development methods (which usually follow an empirical approach were applied. The purpose of this research supported by Groupement Scientifique Moteur (GSM was to design a lean-burn sparkignition engine with the object of reducing pollutant emissions and fuel consumption. We try to develop a promising new approach that follows a scientific methodology based in particular on the use of predictive computer codes. The objective of this project is to design an engine that runs on a lean or possibly dilute mixture that will meet European pollution regulations. This lean-burn solution, combined with oxidation catalysis, is considered as an alternative to threeway catalysis, which imposes operation at stoichiometry. The original configuration is a 4-valve engine. One of the advantages this engine offers is great flexibility in changing the inlet conditions. This provides a way of optimizing internal fluid motion, which turns out to be a determining factor in the ability to operate with a lean or dilute mixture. The operation of an engine with a lean or dilute mixture results in substantially reducing nitrogen oxide (NOx emissions, virtually eliminating carbon dioxide (CO

Lean Management Systems in Radiology: Elements for Success.

Science.gov (United States)

Schultz, Stacy R; Ruter, Royce L; Tibor, Laura C

2016-01-01

This article is a review of the literature on Lean and Lean Management Systems and how they have been implemented in healthcare organizations and particularly in radiology departments. The review focuses on the elements required for a successful implementation of Lean by applying the principles of a Lean Management System instead of a Lean tools-only approach. This review shares the successes and failures from healthcare organizations' efforts to improve the quality and safety of the services they provide. There are a limited number of healthcare organizations in the literature who have shared their experiences and additional research is necessary to determine whether a Lean Management System is a viable alternative to the current management structure in healthcare.

Lean practices for quality results: a case illustration.

Science.gov (United States)

Hwang, Pauline; Hwang, David; Hong, Paul

2014-01-01

Increasingly, healthcare providers are implementing lean practices to achieve quality results. Implementing lean healthcare practices is unique compared to manufacturing and other service industries. The purpose of this paper is to present a model that identifies and defines the lean implementation key success factors in healthcare organisations. The model is based on an extant literature review and a case illustration that explores actual lean implementation in a major USA hospital located in a Midwestern city (approximately 300,000 people). An exploratory/descriptive study using observation and follow-up interviews was conducted to identify lean practices in the hospital. Lean practice key drivers include growing elderly populations, rising medical expenses, decreasing insurance coverage and decreasing management support. Effectively implementing lean practices to increase bottom-line results and improve organisational integrity requires sharing goals and processes among healthcare managers and professionals. An illustration explains the model and the study provides a sound foundation for empirical work. Practical implications are included. Lean practices minimise waste and unnecessary hospital stays while simultaneously enhancing customer values and deploying resources in supply systems. Leadership requires clear project targets based on sound front-end planning because initial implementation steps involve uncertainty and ambiguity (i.e. fuzzy front-end planning). Since top management support is crucial for implementing lean practices successfully, a heavyweight manager, who communicates well both with top managers and project team members, is an important success factor when implementing lean practices. Increasingly, green orientation and sustainability initiatives are phrases that replaced lean practices. Effective results; e.g. waste reduction, employee satisfaction and customer values are applicable to bigger competitive challenges arising both in specific

Lean Management Genesis

Directory of Open Access Journals (Sweden)

Parkes Aneta

2015-12-01

Full Text Available Lean Management is a philosophy and management concept, based on reduction of the waste and resources used in the process of producing goods and providing services. Lean Management genesis dates back to scientific management in America (for example concepts of H. Ford and F.W. Taylor and quality management, including development of TQM concept. Japanese Toyota Production System has been inspired by chosen elements of these concepts, and then it evolved towards global concept called Toyota Way (which connects production rules with values and work attitude.

Improving healthcare using Lean processes.

Science.gov (United States)

Baker, G Ross

2014-01-01

For more than a decade, healthcare organizations across Canada have been using Lean management tools to improve care processes, reduce preventable adverse events, increase patient satisfaction and create better work environments. The largest system-wide effort in Canada, and perhaps anywhere, is currently under way in Saskatchewan. The jury is still out on whether Lean efforts in that province, or elsewhere in Canada, are robust enough to transform current delivery systems and sustain new levels of performance. This issue of Healthcare Quarterly features several articles that provide a perspective on Lean methods in healthcare. Copyright © 2014 Longwoods Publishing.

Assessment of insulin resistance in lean women with polycystic ovary syndrome.

Science.gov (United States)

Morciano, Andrea; Romani, Federica; Sagnella, Francesca; Scarinci, Elisa; Palla, Carola; Moro, Francesca; Tropea, Anna; Policola, Caterina; Della Casa, Silvia; Guido, Maurizio; Lanzone, Antonio; Apa, Rosanna

2014-07-01

To develop and validate a specific simple measure of insulin sensitivity using oral glucose tolerance test (OGTT) values for lean polycystic ovary syndrome (PCOS) women. Retrospective study. Gynecologic Outpatient Clinic of University Hospital, affiliated with Unit of Gynecologic Endocrinology. Totals of 201 lean and 198 overweight/obese (ov-ob) nondiabetic PCOS patients were retrospectively selected. None. All patients underwent OGTT, euglycemic-hyperinsulinemic clamp, and androgenic and biochemical assays. The predictive performance of each insulin resistance (IR) index was analyzed with the use of receiver operating characteristic (ROC) curves. Higher correlation coefficients with clamp studies were obtained with the Belfiore Area (RS=0.579) and the homeostasis-model assessment (HOMA)-M120 (RS=-0.576) in lean PCOS patients and with the Sib (RS=0.697) in ov-ob PCOS patients. The best predictive index of IR in lean PCOS was a HOMA-M120 value of ≥12.8 or more (area under the ROC curve [AUC] 92.4%). In the ov-ob PCOS population, the best predictive performance was obtained by a Sib of ≤10.2 or less (AUC 85.7%). IR should be assessed in all PCOS women, both lean and ov-ob subjects. The HOMA-M120 resulted as a very simple tool, validated specifically for the lean PCOS woman whose cardiometabolic impairment is more frequently misunderstood. Copyright © 2014 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

The Hybrid Lean System to Improve Manufacturing Environment

Directory of Open Access Journals (Sweden)

Ahmad Ahmad Nur Aizat

2017-01-01

Full Text Available Lean manufacturing is a systematic approch could increase manufacturing competitiveness by identifying and elminating waste through lean tools. However, these tools are often categorized into different groups, continues to be difficult for companies to select the most appropriate lean tool to be adopted, especially in respect of the SMEs whose knowledge of lean tools and associated principles are limited. This study is to propose solution on how to implement appropriate lean tools in food manufacturing industry located at Rengit, Johor. Qualitative method is used as a methodology to see the changes after the implementation of lean tools. Interview session also a part of method to collect data from respondents. The finding from this paper shows that implementation of an appropriate lean tool will help to eliminate waste in industry sector, maintain and control the inventory, improve quality of the product and improve overall operational process.

Using Dynamic Value Stream Mapping and Lean Accounting Box Scores to Support Lean Implementation

Science.gov (United States)

Woehrle, Stephen L.; Abou-Shady, Louay

2010-01-01

Lean has proven to be an effective management philosophy for improving businesses in a competitive market by eliminating waste and improving operations. An impact of implementing lean projects is the rapid reduction in inventory levels, which gives management the false impression that profits are decreasing while workers on the shop floor observe…

Researching Lean: Methodological implications of loose definitions

DEFF Research Database (Denmark)

Brännmark, Mikael; Langstrand, Jostein; Johansson, Stina

2012-01-01

practices seem to overlap with other popular management concepts, such as High Performance Work Systems, World Class Manufacturing and Total Quality Management. This confusion, combined with different methodological and theoretical traditions, has led to much debate and contradictory conclusions regarding...... Lean. The purpose of the paper is to illustrate some key methodological issues that need to be considered in future Lean research to allow increased understanding of Lean effects for different stakeholders, primarily meaning the customer, employer and employees. Design/methodology/approach – The paper...... on the case studies, we suggest that future investigations describe the Lean interventions in more detail. General descriptions or analogies, e.g. ‘learning organizations’, presumably increase the present confusion regarding Lean impact on different stakeholders. The case studies also illustrate...

Lean leadership attributes: a systematic review of the literature.

Science.gov (United States)

Aij, Kjeld Harald; Teunissen, Maurits

2017-10-09

Purpose Emphasis on quality and reducing costs has led many health-care organizations to reconfigure their management, process, and quality control infrastructures. Many are lean, a management philosophy with roots in manufacturing industries that emphasizes elimination of waste. Successful lean implementation requires systemic change and strong leadership. Despite the importance of leadership to successful lean implementation, few researchers have probed the question of ideal leadership attributes to achieve lean thinking in health care. The purpose of this paper is to provide insight into applicable attributes for lean leaders in health care. Design/methodology/approach The authors systematically reviewed the literature on principles of leadership and, using Dombrowski and Mielke's (2013) conceptual model of lean leadership, developed a parallel theoretical model for lean leadership in health care. Findings This work contributes to the development of a new framework for describing leadership attributes within lean management of health care. Originality/value The summary of attributes can provide a model for health-care leaders to apply lean in their organizations.

Targeting burn prevention in Ukraine: evaluation of base knowledge in burn prevention and first aid treatment.

Science.gov (United States)

Gamelli, Liza; Mykychack, Iryna; Kushnir, Antin; Driscoll, Daniel N; Fuzaylov, Gennadiy

2015-01-01

Burn prevention has been identified by the World Health Organization (WHO) as a topic in need of further investigation and education throughout the world, with an increased need in low-income countries. It has been noted that implementing educational programs for prevention in high income countries has aided in lowering the rate of burn injuries. The purpose of this study is to evaluate the current education level of knowledge of prevention and first aid treatment of scald burns. A prevention campaign will target these educational needs as a part of an outreach program to improve burn care in Ukraine. The research team evaluated the current health structure in Ukraine and how it could benefit from the increased knowledge of burn prevention and first aid. A test was designed to assess the baseline level of knowledge with regard to first aid and scald prevention in parents, pregnant woman, and healthcare and daycare providers. A total of 14,456 tests were sent to pediatric clinics, obstetrician clinics, and daycare facilities to test respondents. A total of 6,120 completed tests were returned. Doctors presented with the highest level of knowledge averaging 77.0% on prevention and 67.5% on first aid while daycare workers presented the largest gap in knowledge at 65.0% in prevention and 54.3% in first aid. Interest in further educational materials was reported by 92% of respondents. The results of this study clearly show a lack of knowledge in first aid and prevention of scald burn injury in all the populations tested.

Assessment of insulin resistance and impaired glucose tolerance in lean women with polycystic ovary syndrome.

Science.gov (United States)

Stovall, Dale William; Bailey, Amelia Purser; Pastore, Lisa M

2011-01-01

To analyze insulin resistance (IR) and determine the need for a 2-hour oral glucose tolerance test (OGTT) for the identification of IR and impaired glucose tolerance (IGT) in lean nondiabetic women with polycystic ovary syndrome (PCOS). This was a cross-sectional analysis of treatment-naive women with PCOS who enrolled in a university-based clinical trial. Nondiabetic women with PCOS based on the Eunice Kennedy Shriven National Institute of Child Health and Human Development (NICHD) definition, aged 18-43 years and weighing ≤113 kg, were evaluated. Glucose and insulin levels were assessed at times 0, 30, 60, 90, and 120 minutes after a 75-g glucose load. Lean was defined as body mass index (BMI) women was studied. The prevalence of IR was 0% among lean women vs. 21% among nonlean subjects based on fasting insulin I(0) and 40%-68% based on two different homeostatic model assessment (HOMA) cutoff points (p women with IR had a BMI ≥ 28. Controlling for age and race, BMI explained over 57% of the variation in insulin fasting (I(o)), glucose fasting/Io (G(o)/I(o)), the qualitative insulin sensitivity check index (QUICKI), and HOMA and was a highly significant predictor of these outcomes (p lean PCOS women had IGT based on a 2-hour OGTT, and no lean subjects had IGT based on their fasting blood glucose. Diabetes mellitus, IGT, and IR are far less common in young lean women with PCOS compared with obese women with PCOS. These data imply that it is unnecessary to routinely perform either IR testing or 2-hour OGTT in lean women with PCOS; however, greater subject accumulation is needed to determine if OGTT is necessary in lean women with PCOS. BMI is highly predictive of both insulin and glucose levels in women with PCOS.

CRITICAL SUCCESS FACTORS FOR IMPLEMENTING LEAN PRACTICES IN IT SUPPORT SERVICES

Directory of Open Access Journals (Sweden)

Goutam Kundu

2012-12-01

Full Text Available Many studies have been done to identify the critical success factors (CSFs in for successful lean implementation in the manufacturing firms. But, till date, no systematic study has been done to identify the CSFs from the perspective of lean implementation in IT support service sector. This paper aims to address this area. A detailed literature review was undertaken to identify CSFs for lean implementation in manufacturing and services context and to consider their applicability to the IT support services sector. This paper is based on a conceptual discussion of CSFs as applied to the IT support services sector. The authors proposed a set of CSFs which is believed to be suitable for IT support service enterpri ses. The relevance of CSFs will need to be tested and qualitative research is needed to inform further work. The proposed CSFs are aimed at being useful to IT support services sector as a guideline, so as to ensure a positive outcome of the lean implementation process in IT support services sector.

The maintenance management for lean organization

OpenAIRE

Daniel D. GEORGESCU

2010-01-01

The goal of lean maintenance approach is to maintain organization international competitiveness. In the spirit of continuously improvement, in the paper it is shown how by adjusting some Lean manufacturing specific techniques for Total Productive Maintenance (TPM) system, was born new maintenance system named Lean TPM. This is a systemic approach with three techniques, which don’t exclude specific techniques of TPM pillars, but complete them: the 7Ss as a critical first step in any improvemen...

Apply Lean Thinking in Project Management

OpenAIRE

Pham Ngoc, Lan

2015-01-01

The purpose of this thesis was to study the effects of Lean Thinking in Project Management and how applying Lean Project Management could enhance the productivity of project work. The study was carried using theoretical research and collecting empirical data from three interviews and one case study at a local company. At the end of the study, the major project management problems at the company were identified and analyzed following Lean Principles. It was also pointed out where there...

Clinically lean; "cutting the crap".

Science.gov (United States)

Caldwell, G

2012-01-01

Proponents of Lean Philosophy believe that successful businesses must reduce waste in working time and resources to a minimum, and maximise their use in productive work. The productive work of the Acute Medical Unit is to provide effective clinical management to a daily cohort of acutely ill patients. Many Clinicians are cynical about Lean. In this article, Dr Caldwell discusses how many clinicians complain of too much crap in the workplace, which gets in the way of swift, safe high quality clinical care. He argues that "Cutting the Crap" in the Acute Medical Unit is entirely consistent with Lean approaches to management of complex systems.

The relationships between Lean manufacturing, management accounting and firm performance

DEFF Research Database (Denmark)

Kristensen, Thomas Borup; Nielsen, Henrik; Grasso, Lawrency

2016-01-01

with management accounting practices. Specifically, we document that Lean manufacturing is positively associated with Value Stream Costing, Lean visual controls and, more importantly, measures of labor and materials efficiency. Lean manufacturing is positively related to Lean thinking and both are positively...... associated with operational performance and so are Lean visual controls. We also document that the management accounting practices intervene affecting operational performance and they intervene with Lean thinking as well. Lastly, the relationship between Lean manufacturing and measures of labor and materials......Lean manufacturing has been adopted by numerous western companies as an answer to an increasing competitive environment. Lean manufacturing is seen as an enterprise-wide strategy encompassing a transformation of manufacturing practices, affecting companies’ management accounting practices and...

The promise of Lean in health care.

Science.gov (United States)

Toussaint, John S; Berry, Leonard L

2013-01-01

An urgent need in American health care is improving quality and efficiency while controlling costs. One promising management approach implemented by some leading health care institutions is Lean, a quality improvement philosophy and set of principles originated by the Toyota Motor Company. Health care cases reveal that Lean is as applicable in complex knowledge work as it is in assembly-line manufacturing. When well executed, Lean transforms how an organization works and creates an insatiable quest for improvement. In this article, we define Lean and present 6 principles that constitute the essential dynamic of Lean management: attitude of continuous improvement, value creation, unity of purpose, respect for front-line workers, visual tracking, and flexible regimentation. Health care case studies illustrate each principle. The goal of this article is to provide a template for health care leaders to use in considering the implementation of the Lean management system or in assessing the current state of implementation in their organizations. Copyright © 2013 Mayo Foundation for Medical Education and Research. Published by Elsevier Inc. All rights reserved.

Lean sigma--will it work for healthcare?

Science.gov (United States)

Bahensky, James A; Roe, Janet; Bolton, Romy

2005-01-01

The manufacturing industry has been using Lean Sigma for years in pursuit of continuous improvement to obtain a competitive advantage. The objectives of these efforts are to use the Lean techniques for reducing cycle times and the Six Sigma concepts for reducing product defects. The Iowa Business Council with several advocates worked with the University of Iowa Hospital and Clinics (UIHC) and two other Iowa hospitals to determine whether Lean Sigma is adaptable in healthcare. A team of 15 people at UIHC used the Kaizen Breakthrough Methodology over a five-day period in an aggressive identification and elimination of non-value added activities in Radiology CT scanning. The results exceeded the initial project objectives and indicated that Lean Sigma is applicable in healthcare. Overall, the Lean Sigma project increased revenue by approximately $750,000 per year. The Kaizen process proved to be successful and interesting. Within three days, the team installed new work flow processes. This implementation-oriented approach is what differentiates Lean Sigma from other quality improvement processes.

Can lean save lives?

Science.gov (United States)

Fillingham, David

2007-01-01

The purpose of this paper is to show how over the last 18 months Bolton Hospitals NHS Trust have been exploring whether or not lean methodologies, often known as the Toyota Production System, can indeed be applied to healthcare. This paper is a viewpoint. One's early experience is that lean really can save lives. The Toyota Production System is an amazingly successful way of manufacturing cars. It cannot be simply translated unthinkingly into a hospital but lessons can be learned from it and the method can be adapted and developed so that it becomes owned by healthcare staff and focused towards the goal of improved patient care. Working in healthcare is a stressful and difficult thing. Everyone needs a touch of inspiration and encouragement. Applying lean to healthcare in Bolton seems to be achieving just that for those who work there.

Bacterial infections in burn patients at a burn hospital in Iran.

Science.gov (United States)

Ekrami, Alireza; Kalantar, Enayat

2007-12-01

The major challenge for a burn team is nosocomial infection in burn patients, which is known to cause over 50% of burn deaths. Most studies on infection in burn patients focus on burn wound infection, whereas other nosocomial infections in these patients are not well described. We undertook this study to determine three types of nosocomial infections viz., burn wound infection, urinary tract infection, and blood stream infection in burn patients in a burn hospital in Iran. During the one year period (May 2003 to April 2004), 182 patients were included in this study. Blood, urine and wound biopsy samples were taken 7 and 14 days after admission to Taleghani Burn hospital. Isolation and identification of microorganisms was done using the standard procedure. Disk diffusion test were performed for all the isolates for antimicrobial susceptibility. Of the 182 patients, 140 (76.9%) acquired at least one type of infection of the 140, 116 patients (82.8%) were culture positive on day 7 while 24 (17.2%) on 14 days after admission. Primary wound infection was most common (72.5%), followed by blood stream (18.6%) and urinary tract infections (8.9 %). The microorganisms causing infections were Pseudomonas aeruginosa (37.5%), Staphylococcus aureus (20.2%), and Acinetobacter baumanni (10.4%). Among these isolates P. aeruginosa was found to be 100 per cent resistant to amikacin, gentamicin , carbenicillin, ciprofloxacin, tobramycin and ceftazidime; 58 per cent of S. aureus and 60 per cent of coagulase negative Staphylococcus were methicillin resistant. High prevalence of nosocomial infections and the presence of multidrug resistant bacteria, and methicillin resistant S. aureus in patients at Taleghani Burn Hospital suggest continuous surveillance of burn infections and develop strategies for antimicrobial resistance control and treatment of infectious complications.

A Model to align the organizational culture to Lean

Directory of Open Access Journals (Sweden)

Mehrsa Taherimashhadi

2018-04-01

Full Text Available Purpose: Since the emergence of Lean Manufacturing many organizations strived to implement it. Nonetheless, sustainable Lean transformation is not as easy as to be simply achieved. Several aspects need to be taken into account before Lean implementation which national and organizational culture are important. By considering influences of national culture on the organizational culture, this paper aims at proposing an evaluation model to determine the cultural weaknesses of an organization and give some recommendations to manage people before implementing Lean. Design/methodology/approach: This research has been conducted based on literature review survey and semi-structured interviews. Research papers, conference proceedings, books, and official websites regarding Lean philosophy were reviewed to find the influence of national culture in Lean implementation. Different databases were scrutinized, from 2015 to 2017, containing Scopus and Web of Science with the time period of 1996-2016. A set of key terms and their combinations were used including: Toyota Production system, Lean production, Lean manufacturing, Lean management, Transformation, Implementation, Barriers/ Impediments/Challenges/Difficulties, Human resources, Success factors, Organizational culture, and National culture. Findings: The proposed evaluation model is a guide for organizations to determine cultural misalignments between the corporate culture and the Lean culture before its implementation and gives some managerial recommendations to correct them. Originality/value: This study is the first attempt to integrate the national models   with Lean culture to provide an evaluation model and some recommendations to help the organization to align its culture to Lean culture before its implementation.

Når lean organiserer på hospitalet

DEFF Research Database (Denmark)

Hauge, Amalie Martinus

Lean er kendt og anvendt af mange offentlige organisationer i Danmark. Selv om Leans anvendelighed de fleste steder er slået fast, bliver Lean imidlertid ved med at udfordre og skabe konflikt. Hvorfor det? Dette spørgsmål – og mange andre – bliver belyst i denne rapport, som er baseret på en Ph...

Lean Accounting - An Ingenious Solution for Cost Optimization

OpenAIRE

Dimi Ofileanu; Dan Ioan Topor

2014-01-01

The aim of this work is to present a new concept in accounting management: Lean Accounting. This work explains the way the lean concept was born; its benefits for the production system of the factories and the necessity of applying lean accounting in the factories which have implemented lean production, taking into account both its advantages and the boundaries of the other cost management methods in those factories.

Implementing lean manufacturing system: ISM approach

Directory of Open Access Journals (Sweden)

Naveen Kumar

2013-09-01

Full Text Available Purpose: Lean Manufacturing System has emerged as an important area of research in Indian context. The requirement of Lean Manufacturing has increased due to defects in products (semi finished and finished and subsequent increase in cost. In this context, this study is an attempt to develop a structural model of the variables, important to implement Lean Manufacturing System in Indian automobile industry. Design/Methodology/Approach: Various variables of lean manufacturing system implementation have been identified from literature review and experts’ opinions. Contextual relationship among these identified variables has been set after carrying out brainstorming session. Further, classification of the variables has been carried out based upon the driving power and dependence. In addition to this, a structural model of variables to implement lean concept in Indian automobile industry has also been developed using Interpretive Structural Modeling (ISM technique. Questionnaire based survey has also been conducted to rank these variables. Findings: Eighteen variables have been identified from the literature and subsequent discussions with experts. Out of which, nine variables have been identified as dependent and nine variables have been identified as driver. No variable has been identified as linkage variable and autonomous variable. From the model developed, ‘Relative cost benefits’ has been identified as top level dependent variable and top management commitment as bottom level most independent variable. Research limitations/Implications: The model so developed is a hypothetical model based upon experts’ opinions. The conclusions so drawn may be further modified to apply in real situation. Practical implication: Clear understanding of interactions among these variables will help organizations to prioritize and manage these variables more effectively and efficiently to draw advantage from lean manufacturing system implementation

In situ oil burning in the marshland environment : soil temperatures resulting from crude oil and diesel fuel burns

International Nuclear Information System (INIS)

Bryner, N.P.; Walton, W.D.; Twilley, W.H.; Roadarmel, G.; Mendelssohn, I.A.; Lin, Q.; Mullin, J.V.

2001-01-01

The unique challenge associated with oil spill cleanups in sensitive marsh environments was discussed. Mechanical recovery of crude or refined hydrocarbons in wetlands may cause more damage to the marsh than the oil itself. This study evaluated whether in situ burning of oiled marshlands would provide a less damaging alternative than mechanical recovery. This was done through a series of 6 crude oil and 5 diesel fuel burns conducted in a test tank to examine the impact of intentional burning of oil spilled in a wetlands environment. There are several factors which may influence how well such an environment would recover from an in situ oil burn, such as plant species, fuel type and load, water level, soil type, and burn duration. This paper focused on soil, air and water temperatures, as well as total heat fluxes that resulted when 3 plant species were exposed to full-scale in situ burns that were created by burning diesel fuel and crude oil. The soil temperatures were monitored during the test burn at three different soil/water elevations for 700 second burn exposures. A total of 184 plant sods were harvested from marshlands in southern Louisiana and were subjected to the burning fuel. They were instrumental in characterizing the thermal and chemical stress that occur during an in-situ burn. The plants were inserted into the test tanks at various water and soil depths. The results indicated that diesel fuel and crude oil burns produced similar soil temperature profiles at each of three plant sod elevations. Although in-situ burning did not appear to remediate oil that had penetrated into the soil, it did effectively remove floating oil from the water surface, thereby preventing it from potentially contaminating adjacent habitats and penetrating the soil when the water recedes. The regrowth and recovery of the plants will be described in a separate report. 25 refs., 7 tabs., 15 figs

ANFO truck burn trials

Energy Technology Data Exchange (ETDEWEB)

Rosen von, B.; Contestabile, E. [Natural Resources Canada, CANMET Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

2003-10-01

This report describes the investigation of a tractor-trailer explosion. A truck loaded with 18,000 kg of commercial explosives, of which 13,000 kg was ammonium nitrate with fuel oil (ANFO), caught fire when it struck a rockcut near Walden, Ontario on August 5, 1998. The fire resulted in the detonation of the load. The Canadian Explosives Research Laboratory (CERL) conducted a test program to examine the suitability of existing explosive transportation regulations. Unconfined burns of ANFO were performed. The accident was recreated in two burn trials in an attempt to identify the mechanism that led from fire to detonation. Two full-scale tests were conducted using complete tractor-trailers, each in a jack-knifed position with most of the explosives placed on the ground in front of the trailer. ANFO was used in the first test to determine its response to thermal stimulus and the likelihood of detonation or explosion. The second test involved ANFO, a slurry and an emulsion. Thermocouples and video cameras were used to observe the burning characteristics of the explosives, the truck and its components. The explosives burned steadily for 80 minutes in each test. Many truck components, such as tires, spring brake chambers and the fuel tank ruptured violently due to the heat. Although no detonation occurred in the test trials, it was concluded that under favourable conditions, many truck components, might produce fragments with enough energy to initiate heat-sensitized explosives. It was suggested that a fragment impact caused the detonation at Walden. 4 refs., 7 tabs., 8 figs.

Effects of Chronic Musculoskeletal Pain on Fertility Potential in Lean and Overweight Male Patients

Directory of Open Access Journals (Sweden)

Fereshteh Dardmeh

2017-01-01

Full Text Available Both chronic pain and obesity are known to affect reproductive hormone profiles in male patients. However, the effect of these conditions, alone or in combination, on male fertility potential has received less attention. 20 chronic musculoskeletal pain patients and 20 healthy controls were divided into lean and overweight subgroups according to their BMI. Current level of chronic pain (visual analogue scale and pressure pain thresholds (PPTs in 16 predefined sites, classically described and tested as painful points on the lower body, were measured. Levels of reproductive hormone and lipid profiles were assessed by ELISA. Sperm concentration and motility parameters were analyzed using a computer-aided sperm analysis system. Sperm concentration, progressive motility, and percentage of hyperactivated sperm were generally lower in the chronic pain patients in both lean and overweight groups. The overweight control and the lean chronic pain groups demonstrated a significantly lower percentage of progressively motile sperm compared with the lean control group, suggesting that musculoskeletal chronic pain may have a negative influence on sperm quality in lean patients. However, due to the potential great negative influence of obesity on the sperm parameters, it is difficult to propose if musculoskeletal chronic pain also influenced sperm quality in overweight patients. Further research in chronic pain patients is required to test this hypothesis.

Improment of process for preparing and testing hydrogels in wound/burn treatment to apply a licence

International Nuclear Information System (INIS)

Doan Thi The; Pham Thi Thu Hong; Doan Binh; Tran Tich Canh; Nguyen Quoc Hien

2007-01-01

Hydrogel based on PVA/PVP/KC/CMC for burn wound dressing has been prepared by cross linking irradiation. The characteristics of the hydrogel such as gel fraction, mechanical properties, the equilibrium swelling degree in water and in pseudo-extra cellular fluid (PECF), and the water vapor transmission rate (WVTR) were measured. The microbe penetration, burn-wound healing effects, skin irritation and sterility level of the hydrogel were tested and analyzed. In addition, a technology system for producing hydrogel in a 500 pieces/batch/4hr scale was designed. (author)

Lean management in academic surgery.

Science.gov (United States)

Collar, Ryan M; Shuman, Andrew G; Feiner, Sandra; McGonegal, Amy K; Heidel, Natalie; Duck, Mary; McLean, Scott A; Billi, John E; Healy, David W; Bradford, Carol R

2012-06-01

Lean is a management system designed to enhance productivity by eliminating waste. Surgical practice offers many opportunities for improving efficiency. Our objective was to determine whether systematic implementation of lean thinking in an academic otolaryngology operating room improves efficiency and profitability and preserves team morale and educational opportunities. In an 18-month prospective quasi-experimental study, a multidisciplinary task force systematically implemented lean thinking within an otolaryngology operating room of an academic health system. Operating room turnover time and turnaround time were measured during a baseline period; an observer-effect period in which workers were made aware that their efficiency was being measured but before implementing lean changes; and an intervention period after redesign principles had been used. The impact on teamwork, morale, and surgical resident education were measured during the baseline and intervention periods through validated surveys. A profit model was applied to estimate the financial implications of the study. There was no difference between the baseline and observer-effect periods of the study for turnover time (p = 0.98) or turnaround time (p = 0.20). During the intervention period, the mean turnover time and turnaround time were significantly shorter than during the baseline period (29 vs 38 minutes; p improved morale after implementation (p = 0.011). Educational metrics were unchanged before and after implementation. The annual opportunity revenue for the involved operating room is $330,000; when extrapolated throughout the operating rooms, lean thinking could create 6,500 hours of capacity annually. Application of lean management techniques to a single operating room and surgical service improved operating room efficiency and morale, sustained resident education, and can provide considerable financial gains when scaled to an entire academic surgical suite. Copyright © 2012. Published by

Study of ignition, combustion, and production of harmful substances upon burning solid organic fuel at a test bench with a vortex chamber

Science.gov (United States)

Burdukov, A. P.; Chernetskiy, M. Yu.; Dekterev, A. A.; Anufriev, I. S.; Strizhak, P. A.; Greben'kov, P. Yu.

2016-01-01

Results of investigation of furnace processes upon burning of pulverized fuel at a test bench with a power of 5 MW are presented. The test bench consists of two stages with tangential air and pulverized coal feed, and it is equipped by a vibrocentrifugal mill and a disintegrator. Such milling devices have an intensive mechanical impact on solid organic fuel, which, in a number of cases, increases the reactivity of ground material. The processes of ignition and stable combustion of a mixture of gas coal and sludge (wastes of concentration plant), as well as Ekibastus coal, ground in the disintegrator, were studied at the test bench. The results of experimental burning demonstrated that preliminary fuel grinding in the disintegrator provides autothermal combustion mode even for hardly inflammable organic fuels. Experimental combustion of biomass, wheat straw with different lignin content (18, 30, 60%) after grinding in the disintegrator, was performed at the test bench in order to determine the possibility of supporting stable autothermal burning. Stable biofuel combustion mode without lighting by highly reactive fuel was achieved in the experiments. The influence of the additive GTS-Powder (L.O.M. Leaders Co., Ltd., Republic of Korea) in the solid and liquid state on reducing sulfur oxide production upon burning Mugun coal was studied. The results of experimental combustion testify that, for an additive concentration from 1 to 15% of the total mass of the burned mixture, the maximum SO2 concentration reduction in ejected gases was not more than 18% with respect to the amount for the case of burning pure coal.

Effect of Soret diffusion on lean hydrogen/air flames at normal and elevated pressure and temperature

KAUST Repository

Zhou, Zhen; Hernandez Perez, Francisco; Shoshin, Yuriy; van Oijen, Jeroen A.; de Goey, Laurentius P.H.

2017-01-01

The influence of Soret diffusion on lean premixed flames propagating in hydrogen/air mixtures is numerically investigated with a detailed chemical and transport models at normal and elevated pressure and temperature. The Soret diffusion influence on the one-dimensional (1D) flame mass burning rate and two-dimensional (2D) flame propagating characteristics is analysed, revealing a strong dependency on flame stretch rate, pressure and temperature. For 1D flames, at normal pressure and temperature, with an increase of Karlovitz number from 0 to 0.4, the mass burning rate is first reduced and then enhanced by Soret diffusion of H2 while it is reduced by Soret diffusion of H. The influence of Soret diffusion of H2 is enhanced by pressure and reduced by temperature. On the contrary, the influence of Soret diffusion of H is reduced by pressure and enhanced by temperature. For 2D flames, at normal pressure and temperature, during the early phase of flame evolution, flames with Soret diffusion display more curved flame cells. Pressure enhances this effect, while temperature reduces it. The influence of Soret diffusion of H2 on the global consumption speed is enhanced at elevated pressure. The influence of Soret diffusion of H on the global consumption speed is enhanced at elevated temperature. The flame evolution is more affected by Soret diffusion in the early phase of propagation than in the long run due to the local enrichment of H2 caused by flame curvature effects. The present study provides new insights into the Soret diffusion effect on the characteristics of lean hydrogen/air flames at conditions that are relevant to practical applications, e.g. gas engines and turbines.

Effect of Soret diffusion on lean hydrogen/air flames at normal and elevated pressure and temperature

KAUST Repository

Zhou, Zhen

2017-04-12

The influence of Soret diffusion on lean premixed flames propagating in hydrogen/air mixtures is numerically investigated with a detailed chemical and transport models at normal and elevated pressure and temperature. The Soret diffusion influence on the one-dimensional (1D) flame mass burning rate and two-dimensional (2D) flame propagating characteristics is analysed, revealing a strong dependency on flame stretch rate, pressure and temperature. For 1D flames, at normal pressure and temperature, with an increase of Karlovitz number from 0 to 0.4, the mass burning rate is first reduced and then enhanced by Soret diffusion of H2 while it is reduced by Soret diffusion of H. The influence of Soret diffusion of H2 is enhanced by pressure and reduced by temperature. On the contrary, the influence of Soret diffusion of H is reduced by pressure and enhanced by temperature. For 2D flames, at normal pressure and temperature, during the early phase of flame evolution, flames with Soret diffusion display more curved flame cells. Pressure enhances this effect, while temperature reduces it. The influence of Soret diffusion of H2 on the global consumption speed is enhanced at elevated pressure. The influence of Soret diffusion of H on the global consumption speed is enhanced at elevated temperature. The flame evolution is more affected by Soret diffusion in the early phase of propagation than in the long run due to the local enrichment of H2 caused by flame curvature effects. The present study provides new insights into the Soret diffusion effect on the characteristics of lean hydrogen/air flames at conditions that are relevant to practical applications, e.g. gas engines and turbines.

Indførelse af Lean principper

DEFF Research Database (Denmark)

Balmer, Christian; Michelsen, Aage U

2004-01-01

I artiklen beskrives, hvorledes lean-principper er indført i en forsikringsvirksomhed samt de opnåede resultater.......I artiklen beskrives, hvorledes lean-principper er indført i en forsikringsvirksomhed samt de opnåede resultater....

LEAN PRACTICES FOR PRODUCT DEVELOPMENT PROCESS

Directory of Open Access Journals (Sweden)

Guilherme Luz Tortorella

2015-06-01

Full Text Available Lean product development (LPD is an approach that comprises lean principles and management practices that aim to reduce waste and improve operational effectiveness throughout the entire value stream in continuous improvement endless journey. Due to that, the ability to innovate, change and learn continuously is a key element in order to minimize product development problems. Several LPD techniques are presented in the literature as possible enablers for lean implementation. However, little has been known about the impact of these enablers on the problems related to product development processes. Thus, this paper aims to examine the relationship between five LPD practices’ constructs and the occurrence frequency of eleven LPD problems’ constructs in companies that are implementing lean. Moreover, the identification of relevant relationships between LPD practices’ and problems’ constructs may contribute to specify the contexts in which problems are expected to occur. The study sample comprises sixty four companies already undergoing lean implementation both in shop floor and offices area. The results indicate that the same practices’ constructs, which are deemed as influential for minimizing LPD problems, present different relationship intensities among them.

Why Lean doesn't work for everyone.

Science.gov (United States)

Kaplan, Gary S; Patterson, Sarah H; Ching, Joan M; Blackmore, C Craig

2014-12-01

Popularisation of Lean in healthcare has led to emphasis on Lean quality improvement tools in isolation, with inconsistent results. We argue that delivery of safer, more efficient, and higher quality-patient focused care requires organisational transformation of which the Lean toolkit is only one component. To successfully facilitate system transformation toward higher quality care at lower cost, Lean tools must be part of a comprehensive management system, within a supportive institutional culture, and with committed leadership. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Lean education an overview of current issues

CERN Document Server

Flumerfelt, Shannon; Kahlen, Franz-Josef

2017-01-01

This edited volume presents a structured approach to a new lean education curriculum, implemented for the education of engineers, managers, administrators as well as human resources developers. The authorship comprises professors and lecturers, trainers and practitioners who educate future professionals in Lean Thinking principles and tools. This edited book provides a platform for authors to share their efforts in building a Body of Knowledge (BoK) for Lean Education. The topical spectrum is state-of-the-art in this field, but the book also includes a glimpse into future developments. This is a highly informative and carefully presented book, providing valuable insight for scholars with an interest in Lean Education.

Leveraging lean in the office: Lean office needs a novel and differentiated approach

OpenAIRE

Rüttimann, Bruno G.; Fischer, Urs P.; Stöckli, Martin T.

2014-01-01

Lean Six Sigma tools have been increasingly employed also in the service industry, however with different success as field studies have shown. The reason not only has to be attributed to a poor Change Management, but can also be attributed to the intrinsic characteristics of the Lean techniques, which have been tailored to sustain a stable customer-takted pull-manufacturing principle. An office workplace shows significant differences to a procedural shop floor environment, as it comprises bot...

Reducing waste in administrative services with lean principles

NARCIS (Netherlands)

Wijnhoven, Alphonsus B.J.M.; Beckers, David; Amrit, Chintan Amrit

2016-01-01

In the last few decades, lean techniques have been developed for removing with waste in manufacturing. More recently, lean is used outside the manufacturing context as well. This article focuses on using lean thinking for reducing waste in administrative services, i.e., business services with

Bacteriological profile of burn wound isolates in a burns center of a tertiary hospital

Directory of Open Access Journals (Sweden)

Amankwa Richcane

2017-01-01

Full Text Available Objective: To determine the bacteriological profile and antimicrobial susceptibility patterns of burn wound isolates.Methods: Swabs were taken from burn wound of patients admitted to Ward D2C and Burns Intensive Care Unit (BICU from December 2014 to November 2015. Samples were processed at the Microbiology Laboratory for identification and sensitivity. Bacteria isolated were identified using their morphological characteristics, Gram staining reaction and biochemical tests. The antimicrobial susceptibility testing was done using Kirby-Bauer disc diffusion method. Questionnaires were also administered to study participants to obtain information on demography, kind of first aid received, antibiotics received prior to culture and sensitivity.Results: A total of 86 patients comprising 45 patients from Ward D2C and 41 from BICU participated in the study. Males were 51(59.3% and females 35 (40.7%. Age of participants ranged from 0–56+ years. Pseudomonas aeruginosa was the commonest pathogen isolated 26(30.2%, followed by Pseudomonas spp. 21(24.4%, Escherichia coli 17(19.8%, Klebsiella spp. 12(14.0%. Coagulase negative Staphylococcus accounted for 2(2.3%. Overall prevalence of infection in the study was 90.7%.Conclusions: Burn wound infection continues to be a major challenge in burn centers. Regular surveillance of commonly identified pathogens in the ward and their antimicrobial susceptibility will guide proper empiric selection of antibiotics for management of burn wounds.

Lean mass predicts conditioned pain modulation in adolescents across weight status.

Science.gov (United States)

Stolzman, S; Hoeger Bement, M

2016-07-01

There is a wide continuum of conditioned pain modulation (CPM) in adults with older adults experiencing an attenuated CPM response compared with younger adults. Less is known for adolescents and the role of anthropometrics. Fifty-six adolescents (15.1 ± 1.8 years; 32 normal weight and 24 overweight/obese; 27 boys) completed in a CPM session that included anthropometric testing. Pressure pain thresholds were measured at the nailbed and deltoid muscle (test stimuli) with the foot submerged in a cool or ice water bath (conditioning stimulus). Weight status, body composition (Dual-energy X-ray absorptiometry scan), physical activity levels and clinical pain were also evaluated. The CPM response in adolescents was similar across sites (nailbed vs. deltoid), weight status (normal vs. overweight/obese) and sex. CPM measured at the deltoid muscle was positively associated with left arm lean mass but not fat mass; lean mass of the arm uniquely predicted 10% of the CPM magnitude. CPM measured at the nailbed was positively correlated with physical activity levels. These results suggest that lean mass and physical activity levels may contribute to endogenous pain inhibition in adolescents across weight status. © 2016 European Pain Federation - EFIC®

Physical Activity Modifies the Association between Dietary Protein and Lean Mass of Postmenopausal Women.

Science.gov (United States)

Martinez, Jessica A; Wertheim, Betsy C; Thomson, Cynthia A; Bea, Jennifer W; Wallace, Robert; Allison, Matthew; Snetselaar, Linda; Chen, Zhao; Nassir, Rami; Thompson, Patricia A

2017-02-01

Maintenance of lean muscle mass and related strength is associated with lower risk for numerous chronic diseases of aging in women. Our aim was to evaluate whether the association between dietary protein and lean mass differs by physical activity level, amino acid composition, and body mass index categories. We performed a cross-sectional analysis of a prospective cohort. Participants were postmenopausal women from the Women's Health Initiative with body composition measurements by dual-energy x-ray absorptiometry (n=8,298). Our study measured percent lean mass, percent fat mass, and lean body mass index. Linear regression models adjusted for scanner serial number, age, calibrated energy intake, race/ethnicity, neighborhood socioeconomic status, and recreational physical activity were used to determine the relationship between protein intake and body composition measures. Likelihood ratio tests and stratified analysis were used to investigate physical activity and body mass index as potential effect modifiers. Biomarker-calibrated protein intake was positively associated with percent lean mass; women in the highest protein quintile had 6.3 percentage points higher lean mass than the lowest quintile (Plean body mass index were both inversely related to protein intake (both Plean body mass index (P interaction =0.011). Leucine intake was associated with lean mass, as were branched chain amino acids combined (both Plean mass in postmenopausal women. Importantly, those that also engage in physical activity have the highest lean mass across body mass index categories. Copyright © 2017 Academy of Nutrition and Dietetics. Published by Elsevier Inc. All rights reserved.

Lean accounting – as a future accounting system

Directory of Open Access Journals (Sweden)

M.V. Koryagin

2017-12-01

Full Text Available The historical development of lean accounting is researched. The comparison of lean accounting and accounting is carried out. The article determines the lean accounting basic principles, which are the basis for the selection of main ten steps of upgrading to the system of lean accounting: the evaluation of the current situation and the expected development prospects of the enterprise; the development of the principles of implementing lean accounting; the determining the production parameters and methodology of the economic model construction; the organization of lean manufacturing environment and reducing most of the stock; the determining the flow of value creation; the rejection of variable accounting and reverse cancellation of all labor costs and the cost of materials; the rejection of tracking stocks and assign of the costs directly to the costs of sales when occurred; the definition of client-targeted spending; the relationship with suppliers and automation of the accounts payable; the relationship with customers and automation of the payments received.

Quality improvement in basic histotechnology: the lean approach.

Science.gov (United States)

Clark, David

2016-01-01

Lean is a comprehensive system of management based on the Toyota production system (TPS), encompassing all the activities of an organization. It focuses management activity on creating value for the end-user by continuously improving operational effectiveness and removing waste. Lean management creates a culture of continuous quality improvement with a strong emphasis on developing the problem-solving capability of staff using the scientific method (Deming's Plan, Do, Check, Act cycle). Lean management systems have been adopted by a number of histopathology departments throughout the world to simultaneously improve quality (reducing errors and shortening turnround times) and lower costs (by increasing efficiency). This article describes the key concepts that make up a lean management system, and how these concepts have been adapted from manufacturing industry and applied to histopathology using a case study of lean implementation and evidence from the literature. It discusses the benefits, limitations, and pitfalls encountered when implementing lean management systems.

Total and Lower Extremity Lean Mass Percentage Positively Correlates With Jump Performance.

Science.gov (United States)

Stephenson, Mitchell L; Smith, Derek T; Heinbaugh, Erika M; Moynes, Rebecca C; Rockey, Shawn S; Thomas, Joi J; Dai, Boyi

2015-08-01

Strength and power have been identified as valuable components in both athletic performance and daily function. A major component of strength and power is the muscle mass, which can be assessed with dual-energy x-ray absorptiometry (DXA). The primary purpose of this study was to quantify the relationship between total body lean mass percentage (TBLM%) and lower extremity lean mass percentage (LELM%) and lower extremity force/power production during a countermovement jump (CMJ) in a general population. Researchers performed a DXA analysis on 40 younger participants aged 18-35 years, 28 middle-aged participants aged 36-55 years, and 34 older participants aged 56-75 years. Participants performed 3 CMJ on force platforms. Correlations revealed significant and strong relationships between TBLM% and LELM% compared with CMJ normalized peak vertical ground reaction force (p lean mass percentages. The findings have implications in including DXA-assessed lean mass percentage as a component for evaluating lower extremity strength and power. A paired DXA analysis and CMJ jump test may be useful for identifying neuromuscular deficits that limit performance.

Willingness-to-pay function for two fuel treatments to reduce wildfire acreage burned: A scope test and comparison of white and hispanic households

Science.gov (United States)

John B. Loomis; Hung Le Trong; Armando González-Cabán

2009-01-01

We estimate a marginal benefit function for using prescribed burning and mechanical fuel reduction programs to reduce acres burned by wildfire in three states. Since each state had different acre reductions, a statistically significant coefficient on the reduction in acres burned is also a split sample scope test frequently used as an indicator of the internal validity...

Testing program for burning plasma experiment vacuum vessel bolted joint

International Nuclear Information System (INIS)

Hsueh, P.K.; Khan, M.Z.; Swanson, J.; Feng, T.; Dinkevich, S.; Warren, J.

1992-01-01

As presently designed, the Burning Plasma Experiment vacuum vessel will be segmentally fabricated and assembled by bolted joints in the field. Due to geometry constraints, most of the bolted joints have significant eccentricity which causes the joint behavior to be sensitive to joint clamping forces. Experience indicates that as a result of this eccentricity, the joint will tend to open at the side closest to the applied load with the extent of the opening being dependent on the initial preload. In this paper analytical models coupled with a confirmatory testing program are developed to investigate and predict the non-linear behavior of the vacuum vessel bolted joint

LEAN Tools in the IT Sector

Directory of Open Access Journals (Sweden)

Zoltan VAJNA

2015-05-01

Full Text Available Nowadays the LEAN tools with their proven efficiency are indispensable parts of the production management. I think there is no producing enterprise that cannot utilize a wide variety of these LEAN tools. The question now is how these tools can support companies in increasing the efficiency of their supporting IT processes. In this study I will demonstrate how these well-known LEAN tools from production management can be used in IT management to create more cost-effective, efficient and transparent solutions during the IT system development and IT operation activities. I will show respectively without attempting to be comprehensive the most important tools of the LEAN management and I will analyse how these tools can be used in the IT sector. At the end of this study I will demonstrate what the IT managers think about the practical use of these tools.

Lean in service industries: A literature review

Science.gov (United States)

V, Vignesh; Suresh, M.; Aramvalarthan, S.

2016-09-01

Lean service is an amalgamation of tools and practices which, if applied appropriately, would definitely improve the existing quality of operations and ensure the generation of a large amount of favourable financial and economic outcomes and improve the behaviour of the workforce. As a result, it assumes of great significance in the fiercely competitive modern world. This article presents a comprehensive bibliographic study about the various lean service practices through a variety of approaches like service improvement, manufacturing, supply chain, market and retailing approaches, etc. Thus it gives a clear view on how the lean services are implemented in various sectors and the contribution of lean service towards improving the quality in the services provided while reducing the costs.

Getting 'Lean': hardwiring process excellence into Northeast Health.

Science.gov (United States)

Brown, Tricia; Duthe, Robert

2009-01-01

Many healthcare organizations are turning to the "Lean" Toyota Production System as a means to hardwire process excellence into their organizations. Northeast Health, an integrated delivery system in New York's capital region, introduced the Lean concept into its culture in 2004. After four years, the organization is beginning to see its staff hardwire Lean thinking into day-to-day behaviors. This paper focuses on the approach used by Northeast Health to introduce Lean concepts into its culture, challenges faced, lessons learned and the factors critical to success.

Pollutant Formation during the Occurrence of Flame Instabilities under Very-Lean Combustion Conditions in a Liquid-Fuel Burner

Directory of Open Access Journals (Sweden)

Maria Grazia De Giorgi

2017-03-01

Full Text Available Recent advances in gas turbine combustor design are aimed at achieving low exhaust emissions, hence modern aircraft jet engines are designed with lean-burn combustion systems. In the present work, we report an experimental study on lean combustion in a liquid fuel burner, operated under a non-premixed (single point injection regime that mimics the combustion in a modern aircraft engine. The flame behavior was investigated in proximity of the blow-out limit by an intensified high rate Charge-Coupled Device (CCD camera equipped with different optical filters to selectively record single species chemiluminescence emissions (e.g., OH*, CH*. Analogous filters were also used in combination with photomultiplier (PMT tubes. Furthermore this work investigates well-mixed lean low NOx combustion where mixing is good and generation of solid carbon particulate emissions should be very low. An analysis of pollutants such as fine particles and gaseous emissions was also performed. Particle number concentrations and size distributions were measured at the exhaust of the combustion chamber by two different particle size measuring instruments: a scanning mobility particle sizer (SMPS and an Electrical Low Pressure Impactor (ELPI. NOx concentration measurements were performed by using a cross-flow modulation chemiluminescence detection system; CO concentration emissions were acquired with a Cross-flow modulation Non-dispersive infrared (NDIR absorption method. All the measurements were completed by diagnostics of the fundamental combustor parameters. The results herein presented show that at very-lean conditions the emissions of both particulate matter and CO was found to increase most likely due to the occurrence of flame instabilities while the NOx were observed to reduce.

Gas chromatographic determination of Di-n-butyl phosphate in radioactive lean organic solvent of FBTR carbide fuel reprocessing

International Nuclear Information System (INIS)

Velavendan, P.; Ganesh, S.; Pandey, N.K.; Kamachi Mudali, U.; Natarajan, R.

2011-01-01

In the present work Di-n- butyl phosphate (DBP) a degraded product of Tri-n-butyl phosphate (TBP) formed by acid hydrolysis and radiolysis in the PUREX process was analyzed. Lean organic streams of different fuel burn-up FBTR carbide fuel reprocessing solution was determined by standard Gas Chromatographic technique. The method involves the conversion of non-volatile Di-n-butyl phosphate into volatile and stable derivatives by the action of diazomethane and then determined by Gas Chromatograph (GC). A calibration graph was made for DBP concentration range of 200-2000 ppm with correlation coefficient of 0.99587 and RSD 1.2 %. (author)

Performance and emission characteristics of a turbocharged CNG engine fueled by hydrogen-enriched compressed natural gas with high hydrogen ratio

Energy Technology Data Exchange (ETDEWEB)

Ma, Fanhua; Wang, Mingyue; Jiang, Long; Chen, Renzhe; Deng, Jiao; Naeve, Nashay; Zhao, Shuli [State Key Laboratory of Automotive Safety and Energy Tsinghua University, Beijing 100084 (China)

2010-06-15

This paper investigates the effect of high hydrogen volumetric ratio of 55% on performance and emission characteristics in a turbocharged lean burn natural gas engine. The experimental data was conducted under various operating conditions including different spark timing, excess air ratio (lambda), and manifold pressure. It is found that the addition of hydrogen at a high volumetric ratio could significantly extend the lean burn limit, improve the engine lean burn ability, decrease burn duration, and yield higher thermal efficiency. The CO, CH{sub 4} emissions were reduced and NO{sub x} emission could be kept an acceptable low level with high hydrogen content under lean burn conditions when ignition timing were optimized. (author)

De praktijk van Lean Six Sigma

NARCIS (Netherlands)

Does, R.J.M.M.; de Koning, H.

2008-01-01

Zowel Lean als Six Sigma zijn benaderingen van kwaliteits- en efficiëntieverbetering die op dit moment sterk in de belangstelling staan van zowel de industrie als de dienstverlening. Lean Six Sigma integreert beide benaderingen. Ze wordt door sommigen gezien als panacee voor alle mogelijke

Just-in-Time og Lean Manufacturing

DEFF Research Database (Denmark)

Michelsen, Aage U.

2004-01-01

Filosofi, principper og teknikker i JIT. Princip i Kanban-styring og dimensionering af et Kanban-system. Lean Thinking og Value Stream Mapping.......Filosofi, principper og teknikker i JIT. Princip i Kanban-styring og dimensionering af et Kanban-system. Lean Thinking og Value Stream Mapping....

Lean Six Sigma in a hospital

NARCIS (Netherlands)

van den Heuvel, J.; Does, R.J.M.M.; de Koning, H.

2006-01-01

Abstract Hospitals today face major challenges. Patients demand quality of care to be improved continuously. Health insurance companies demand the lowest possible prices. Lean Six Sigma is a program that can help healthcare providers to achieve these (seemingly) conflicting goals. Lean Six Sigma is

Safety demonstration tests of air-ventilation system for the postulated explosive burning in a cell of fuel-reprocessing plant

International Nuclear Information System (INIS)

Takada, Junichi; Suzuki, Motoe; Tukamoto, Michio; Koike, Tadao; Nishio, Gunji

1995-03-01

Safety demonstration tests of an explosive burning in a cell in the reprocessing plant has been carried out in JAERI under the auspices of the Science and Technology Agency, to evaluate the safety of an air-ventilation system during the hypothetical explosion. The postulated explosive burning of organic solvent mixed with nitric acid was simulated by solid explosives. The demonstration test was performed using an industrial scale experimental facility simulating to the ventilation system of the large scale reprocessing plant in JAPAN. Propagations of pressure, temperature, and gas velocity through cells and ducts in the ventilation system were measured during the explosive burning under deflagration. Experimental data in this report can be used to evaluate the transport phenomena of radioactive materials in the ventilation system during the explosion, and also to verify computer code CELVA for the safety analysis of ventilation system in the event of explosion accidents. (author)

Bromocriptine and insulin sensitivity in lean and obese subjects

Directory of Open Access Journals (Sweden)

L Bahler

2016-11-01

Full Text Available Bromocriptine is a glucose-lowering drug, which was shown to be effective in obese subjects with insulin resistance. It is usually administered in the morning. The exact working mechanism of bromocriptine still has to be elucidated. Therefore, in this open-label randomized prospective cross-over mechanistic study, we assessed whether the timing of bromocriptine administration (morning vs evening results in different effects and whether these effects differ between lean and obese subjects. We studied the effect of bromocriptine on insulin sensitivity in 8 lean and 8 overweight subjects using an oral glucose tolerance test. The subjects used bromocriptine in randomized cross-over order for 2 weeks in the morning and 2 weeks in the evening. We found that in lean subjects, bromocriptine administration in the evening resulted in a significantly higher post-prandial insulin sensitivity as compared with the pre-exposure visit (glucose area under the curve (AUC 742 mmol/L * 120 min (695–818 vs 641 (504–750, P = 0.036, AUC for insulin did not change, P = 0.575. In obese subjects, both morning and evening administration of bromocriptine resulted in a significantly higher insulin sensitivity: morning administration in obese: insulin AUC (55,900 mmol/L * 120 min (43,236–96,831 vs 36,448 (25,213–57,711, P = 0.012 and glucose AUC P = 0.069; evening administration in obese: glucose AUC (735 mmol/L * 120 min (614–988 vs 644 (568–829, P = 0.017 and insulin AUC, P = 0.208. In conclusion, bromocriptine increases insulin sensitivity in both lean and obese subjects. In lean subjects, this effect only occurred when bromocriptine was administrated in the evening, whereas in the obese, insulin sensitivity increased independent of the timing of bromocriptine administration.

Using lean methodologies for economically and environmentally sustainable foundries

Directory of Open Access Journals (Sweden)

R. M. Torielli

2011-02-01

Full Text Available Lean manufacturing is often seen as a set of tools that reduce the total cost and improve the quality of manufactured products. The lean management philosophy is one which targets waste reduction in every facet of the manufacturing business; however, only recently have studies linked lean management philosophies with improving environmental sustainability. These studies suggest that lean manufacturing is more than a set of lean tools that can optimize manufacturing efficiencies; it is a process and mindset that needs to be integrated into daily manufacturing systems to achieve sustainability. The foundry industry, as well as manufacturing in general, has significant challenges in the current regulatory and political climate with developing an economically and environmentally sustainable business model. Lean manufacturing has proven itself as a model for both economic sustainability and environmental stewardship. Several recent studies have shown that both lean and green techniques and “zero-waste” policies also lead to reductions in overall cost. While these strategies have been examined for general manufacturing, they have not been investigated in detail for the foundry industry. This paper will review the current literature and describe how lean and green can provide a relevant framework for environmentally and economically sustainable foundries. Examples of lean and green technologies and techniques which can be applied to foundries in a global context will be described.

Serum Predictors of Percent Lean Mass in Young Adults.

Science.gov (United States)

Lustgarten, Michael S; Price, Lori L; Phillips, Edward M; Kirn, Dylan R; Mills, John; Fielding, Roger A

2016-08-01

Lustgarten, MS, Price, LL, Phillips, EM, Kirn, DR, Mills, J, and Fielding, RA. Serum predictors of percent lean mass in young adults. J Strength Cond Res 30(8): 2194-2201, 2016-Elevated lean (skeletal muscle) mass is associated with increased muscle strength and anaerobic exercise performance, whereas low levels of lean mass are associated with insulin resistance and sarcopenia. Therefore, studies aimed at obtaining an improved understanding of mechanisms related to the quantity of lean mass are of interest. Percent lean mass (total lean mass/body weight × 100) in 77 young subjects (18-35 years) was measured with dual-energy x-ray absorptiometry. Twenty analytes and 296 metabolites were evaluated with the use of the standard chemistry screen and mass spectrometry-based metabolomic profiling, respectively. Sex-adjusted multivariable linear regression was used to determine serum analytes and metabolites significantly (p ≤ 0.05 and q ≤ 0.30) associated with the percent lean mass. Two enzymes (alkaline phosphatase and serum glutamate oxaloacetate aminotransferase) and 29 metabolites were found to be significantly associated with the percent lean mass, including metabolites related to microbial metabolism, uremia, inflammation, oxidative stress, branched-chain amino acid metabolism, insulin sensitivity, glycerolipid metabolism, and xenobiotics. Use of sex-adjusted stepwise regression to obtain a final covariate predictor model identified the combination of 5 analytes and metabolites as overall predictors of the percent lean mass (model R = 82.5%). Collectively, these data suggest that a complex interplay of various metabolic processes underlies the maintenance of lean mass in young healthy adults.

Teaching Special Decisions in a Lean Accounting Environment

Science.gov (United States)

Haskin, Daniel

2010-01-01

Lean accounting has become increasingly important as more and more companies adopt the lean enterprise model or some variation of it. Cost and managerial accounting textbooks continue to use, almost exclusively, models based on standard overhead absorption, which if used in a lean environment will not accurately reflect the benefits from the…

In-situ burning of Alaskan oils and emulsions: preliminary results of laboratory tests with and without waves

International Nuclear Information System (INIS)

Buist, I.; McCourt, J.; Karunakaran, K.; Gierer, C.; Comins, D.; Glover, N.; McKenzie, B.

1996-01-01

The efficiency of in-situ burning (ISB) as a response tool for oils transported in Alaska was studied. ISB can be an effective measure during an oil spill clean-up and has the potential to quickly remove large amounts of oil from the water surface. However, studies have shown that it is important to act quickly before the oil evaporates and before water-in-oil emulsions form, rendering the slick unignitable. Small-scale laboratory tests were conducted to determine the limits to ignition of slicks of four oils, and to determine the effectiveness of chemical emulsion breakers in extending the ignition limits. Results showed that while evaporation and emulsification could curtail ignition of oil slicks, the addition of a chemical emulsion breaker could extend the limits of ignition and burnability. Preliminary results also showed that waves had an effect on the burning of fresh, weathered and slightly emulsified crude oil. Burn efficiency and burn time were found to decrease with increasing wave energy. 14 refs., 18 tabs., 4 figs

Contractor Work Preparation Process Improvement Using Lean Six Sigma

Directory of Open Access Journals (Sweden)

Asana Kusnadi

2016-06-01

Full Text Available To ensure the health and safety of their workforce and protection of their assets and the environment, a global oil and gas company operating in Indonesia requires comprehensive identification and evaluation of job hazards that were included in work permitting process prior work execution in the field. Based on 20 data points obtained in August 2013, start-working time for contractors who worked for Capital Project Management (CPM Team in Facility B was in average at 09.05 a.m. The aim of this paper is to present how the firm implemented Lean Six Sigma to reduce non-added value activities while fulfilling to its safety requirements and to share lessons learned from practical and theory testing perspective. The methodology used is Lean Six Sigma’s DMAIC (Define, Measure, Analyze, Improve, Control as mandated by the corporate policy of the firm. This research adopts a mix-methods approach, by using both qualitative and quantitative data. This study was a one year longitudinal study of the Lean Six Sigma implementation to improve contractors’ work preparation process. The improvement resulted in reduction of non-value added activities and successfully increased the available working time per day by 59.3 minutes in average. The results of this case study reconfirm Lean Six Sigma as a good management theory since it shows a consistency between the theory and the real practice in a global oil and gas company in Indonesia.

Development of framework for sustainable Lean implementation: an ISM approach

Science.gov (United States)

Jadhav, Jagdish Rajaram; Mantha, S. S.; Rane, Santosh B.

2014-07-01

The survival of any organization depends upon its competitive edge. Even though Lean is one of the most powerful quality improvement methodologies, nearly two-thirds of the Lean implementations results in failures and less than one-fifth of those implemented have sustained results. One of the most significant tasks of top management is to identify, understand and deploy the significant Lean practices like quality circle, Kanban, Just-in-time purchasing, etc. The term `bundle' is used to make groups of inter-related and internally consistent Lean practices. Eight significant Lean practice bundles have been identified based on literature reviewed and opinion of the experts. The order of execution of Lean practice bundles is very important. Lean practitioners must be able to understand the interrelationship between these practice bundles. The objective of this paper is to develop framework for sustainable Lean implementation using interpretive structural modelling approach.

Application of lean thinking to health care: issues and observations

Science.gov (United States)

Joosten, Tom; Bongers, Inge; Janssen, Richard

2009-01-01

Background Incidents and quality problems are a prime cause why health care leaders are calling to redesign health care delivery. One of the concepts used is lean thinking. Yet, lean often leads to resistance. Also, there is a lack of high quality evidence supporting lean premises. In this paper, we present an overview of lean thinking and its application to health care. Development, theory and application of lean thinking to health care Lean thinking evolved from a tool designed to improve operational shop-floor performance at an automotive manufacturer to a management approach with both operational and sociotechnical aspects. Sociotechnical dynamics have until recently not received much attention. At the same time a balanced approach might lead to a situation where operational and sociotechnial improvements are mutually reinforcing. Application to health care has been limited and focussed mainly on operational aspects using original lean tools. A more integrative approach would be to pay more attention to sociotechnical dynamics of lean implementation efforts. Also, the need to use the original lean tools may be limited, because health care may have different instruments and tools already in use that are in line with lean thinking principles. Discussion We believe lean thinking has the potential to improve health care delivery. At the same time, there are methodological and practical considerations that need to be taken into account. Otherwise, lean implementation will be superficial and fail, adding to existing resistance and making it more difficult to improve health care in the long term. PMID:19696048

Implementation of Lean Manufacturing in Romanian Organisations

Directory of Open Access Journals (Sweden)

Ucenic Camelia Ioana

2017-01-01

Full Text Available The implementation of lean manufacturing is one of the main tools for attaining a higher performance level in the Romanian organisations. The study uses data collected at middle management level from organisations located in Transylvania. The organisations come from different fields of activity and are in different stages of lean implementation. The article makes use of quantitative and qualitative instruments for the evaluation of lean in the above mentioned companies. Characteristics as waste reduction, cost, quality, product design have different approaches in the companies. Their way of approach gives useful information regarding the type of company from the point of view of lean manufacturing implementation. This knowledge provides a useful support at different managerial levels in the process of decision making.

A case study of lean, sustainable manufacturing

Directory of Open Access Journals (Sweden)

Geoff Miller

2010-06-01

Full Text Available A small furniture production company has integrated lean tools and sustainability concepts with discrete event simulation modeling and analysis as well as mathematical optimization to make a positive impact on the environment, society and its own financial success. The principles of lean manufacturing that aid in the elimination of waste have helped the company meet ever increasing customer demands while preserving valuable resources for future generations. The implementation of lean and sustainable manufacturing was aided by the use of discrete event simulation and optimization to overcome deficits in lean’s traditional implementation strategies. Lean and green manufacturing can have a more significant, positive impact on multiple measures of operational performance when implemented concurrently rather than separately. These ideas are demonstrated by three applications.

Using Simulation to Explore Lean Manufacturing Implementation Strategies

Science.gov (United States)

Shannon, Patrick W.; Krumwiede, Kip R.; Street, Jeffrey N.

2010-01-01

Lean manufacturing, an outgrowth of the Toyota Production System, has spread far beyond the automobile industry and is seen by many leaders as a key management philosophy in the battle to compete on an international scale. Successful implementation of lean requires that managers and employees be educated in the proper application of lean tools and…

Learning Lean: A Survey of Industry Lean Needs

Science.gov (United States)

Fliedner, Gene; Mathieson, Kieran

2009-01-01

The authors examined business practitioners' preferences for higher education curricula design in general and for what graduates should know about Lean, or waste-reduction efforts. The authors conducted a Web-based survey and found that practitioners are not as concerned about graduates' possessing specific technical skills as they are about them…

Mechanical Deformation Behavior of Lean Duplex 329LA Steel

Energy Technology Data Exchange (ETDEWEB)

Yoon, Byung-Jun [Research Institute of Industrial Science and Technology, Pohang (Korea, Republic of); Choi, Jeom-Yong [POSCO Technical Research Lab., Pohang (Korea, Republic of); Park, Kyung-Tae [Hanvat National University, Daejeon (Korea, Republic of); Lee, Ho Seong [Kyungpook National University, Daegu (Korea, Republic of)

2015-09-15

The tensile response of Lean Duplex 329LA stainless steel was investigated over various strain rates. It was observed that the mechanical response, including in particular the total elongation of the tested alloy, was strongly affected by the strain rate. As the strain rate decreased from 10-1 s-1 to 10-4 s-1, the elongation increased. As the strain rate increased, the deformation mode in an austenite phase was dominated by dislocation glide, resulting in deterioration of the elongation. The substructure of the ferritic phase showed a dislocation cell structure, independent of the applied strain rate. The optimum mechanical properties of lean duplex stainless steel thus can be obtained by controlling the deformation mode in the austenitic phase.

Mechanical Deformation Behavior of Lean Duplex 329LA Steel

International Nuclear Information System (INIS)

Yoon, Byung-Jun; Choi, Jeom-Yong; Park, Kyung-Tae; Lee, Ho Seong

2015-01-01

The tensile response of Lean Duplex 329LA stainless steel was investigated over various strain rates. It was observed that the mechanical response, including in particular the total elongation of the tested alloy, was strongly affected by the strain rate. As the strain rate decreased from 10-1 s-1 to 10-4 s-1, the elongation increased. As the strain rate increased, the deformation mode in an austenite phase was dominated by dislocation glide, resulting in deterioration of the elongation. The substructure of the ferritic phase showed a dislocation cell structure, independent of the applied strain rate. The optimum mechanical properties of lean duplex stainless steel thus can be obtained by controlling the deformation mode in the austenitic phase.

"The largest Lean transformation in the world": the implementation and evaluation of lean in Saskatchewan healthcare.

Science.gov (United States)

Kinsman, Leigh; Rotter, Thomas; Stevenson, Katherine; Bath, Brenna; Goodridge, Donna; Harrison, Liz; Dobson, Roy; Sari, Nazmi; Jeffery, Cathy; Bourassa, Carrie; Westhorp, Gill

2014-01-01

The Saskatchewan Ministry of Health has committed to a multi-million dollar investment toward the implementation of Lean methodology across the province's healthcare system. Originating as a production line discipline (the Toyota Production System), Lean has evolved to encompass process improvements including inventory management, waste reduction and quality improvement techniques. With an initial focus on leadership, strategic alignment, training and the creation of a supportive infrastructure (Lean promotion offices), the goal in Saskatchewan is a whole health system transformation that produces "better health, better value, better care, and better teams." Given the scope and scale of the initiative and the commitment of resources, it is vital that a comprehensive, longitudinal evaluation plan be implemented to support ongoing decision-making and program design. The nature of the initiative also offers a unique opportunity to contribute to health quality improvement science by advancing our understanding of the implementation and evaluation of complex, large-scale healthcare interventions. The purpose of this article is to summarize the background to Lean in Saskatchewan and the proposed evaluation methods. Copyright © 2014 Longwoods Publishing.

Principles of lean planning and control

NARCIS (Netherlands)

Riezebos, J.

2015-01-01

Lean production systems use teams instead of functional departments as well as simple shop floor control methods to manage the flow of orders at the shop floor. Lean shop floor control focuses on robust and visual methods that are able to cope with variation in processing times, routing sequences,

Lean oncology: a new model for oncologists

Directory of Open Access Journals (Sweden)

Montesarchio Vincenzo

2012-04-01

Full Text Available Abstract The history of the term Lean is relatively recent and originates from the Toyota Production System (TPS. The term "Lean" means "thin", which refers to a mental process, operational, productive, no-frills, quick but not hasty, consequential to the previous event. The Lean process flows seamlessly into the result, eliminates unnecessary complications to the effect, prevents unnecessary equipment processes. The idea is to 'do more with less', like using the (few available resources in the most productive way possible, through the elimination of all types of waste that inevitably accompanies every stage of a production process. Lean management is primarily a management philosophy, a system of values and behaviors that goes beyond the mere application of the instrument and that, once internalized, will form the nucleus of the corporate culture. "Lean Oncology" is a term coined to identify a methodology of care and treatment to cancer patients, consisting on process simplification, streamlining of the organizational and routes of drug treatment, detection and elimination of waste. Its main objective is the centrality of the patient.

Lean oncology: a new model for oncologists.

Science.gov (United States)

Montesarchio, Vincenzo; Grimaldi, Antonio Maria; Fox, Bernard A; Rea, Antonio; Marincola, Francesco M; Ascierto, Paolo A

2012-04-25

The history of the term Lean is relatively recent and originates from the Toyota Production System (TPS). The term "Lean" means "thin", which refers to a mental process, operational, productive, no-frills, quick but not hasty, consequential to the previous event. The Lean process flows seamlessly into the result, eliminates unnecessary complications to the effect, prevents unnecessary equipment processes. The idea is to 'do more with less', like using the (few) available resources in the most productive way possible, through the elimination of all types of waste that inevitably accompanies every stage of a production process. Lean management is primarily a management philosophy, a system of values and behaviors that goes beyond the mere application of the instrument and that, once internalized, will form the nucleus of the corporate culture. "Lean Oncology" is a term coined to identify a methodology of care and treatment to cancer patients, consisting on process simplification, streamlining of the organizational and routes of drug treatment, detection and elimination of waste. Its main objective is the centrality of the patient.

Lean IT partnering : How partners create value by developing a lean culture for IT supply and management

NARCIS (Netherlands)

Zee, van der J.T.M.; Blijleven, V.B; Gong, Y.

2015-01-01

Lean, as a philosophy, has been around for quite some time, predominantly in the manufacturing domain. Since the 1990s Lean management provides organizations with a way to achieve superior performance by focusing on customer value, innovation and productivity. In 2011 Steven Bell and Michael Orzen

Model Development and Process Analysis for Lean Cellular Design Planning in Aerospace Assembly and Manufacturing

Science.gov (United States)

Hilburn, Monty D.

Successful lean manufacturing and cellular manufacturing execution relies upon a foundation of leadership commitment and strategic planning built upon solid data and robust analysis. The problem for this study was to create and employ a simple lean transformation planning model and review process that could be used to identify functional support staff resources required to plan and execute lean manufacturing cells within aerospace assembly and manufacturing sites. The lean planning model was developed using available literature for lean manufacturing kaizen best practices and validated through a Delphi panel of lean experts. The resulting model and a standardized review process were used to assess the state of lean transformation planning at five sites of an international aerospace manufacturing and assembly company. The results of the three day, on-site review were compared with baseline plans collected from each of the five sites to determine if there analyzed, with focus on three critical areas of lean planning: the number and type of manufacturing cells identified, the number, type, and duration of planned lean and continuous kaizen events, and the quantity and type of functional staffing resources planned to support the kaizen schedule. Summarized data of the baseline and on-site reviews was analyzed with descriptive statistics. ANOVAs and paired-t tests at 95% significance level were conducted on the means of data sets to determine if null hypotheses related to cell, kaizen event, and support resources could be rejected. The results of the research found significant differences between lean transformation plans developed by site leadership and plans developed utilizing the structured, on-site review process and lean transformation planning model. The null hypothesis that there was no difference between the means of pre-review and on-site cell counts was rejected, as was the null hypothesis that there was no significant difference in kaizen event plans. These

Lean Transformation of Multinational Concerns

DEFF Research Database (Denmark)

Matthiesen, Rikke Vestergaard; Johansen, John

2008-01-01

triggered. This paper reports on exploratory studies from a multinational company adopting centrally managed pilot projects as a transformation mechanism for continuous change towards a lean business system and an organizational culture of continuous improvements (CI). Competitive pressure demands...... from a multinational company adopting centrally managed pilot projects as a transformation mechanism for continuous change towards a lean business system and an organizational culture of continuous improvements (CI)....

Lean healthcare from a change management perspective.

Science.gov (United States)

van Rossum, Lisa; Aij, Kjeld Harald; Simons, Frederique Elisabeth; van der Eng, Niels; Ten Have, Wouter Dirk

2016-05-16

Purpose - Lean healthcare is used in a growing number of hospitals to increase efficiency and quality of care. However, healthcare organizations encounter problems with the implementation of change initiatives due to an implementation gap: the gap between strategy and execution. From a change management perspective, the purpose of this paper is to increase scientific knowledge regarding factors that diminish the implementation gap and make the transition from the "toolbox lean" toward an actual transformation to lean healthcare. Design/methodology/approach - A cross-sectional study was executed in an operating theatre of a Dutch University Medical Centre. Transformational leadership was expected to ensure the required top-down commitment, whereas team leadership creates the required active, bottom-up behavior of employees. Furthermore, professional and functional silos and a hierarchical structure were expected to impede the workforce flexibility in adapting organizational elements and optimize the entire process flow. Findings - The correlation and regression analyses showed positive relations between the transformational leadership and team leadership styles and lean healthcare implementation. The results also indicated a strong relation between workforce flexibility and the implementation of lean healthcare. Originality/value - With the use of a recently developed change management model, the Change Competence Model, the authors suggest leadership and workforce flexibility to be part of an organization's change capacity as crucial success factor for a sustainable transformation to lean healthcare.

Operational practices of lean manufacturing: Potentiating environmental improvements

Directory of Open Access Journals (Sweden)

Marcos José Alves Pinto Junior

2017-10-01

Full Text Available Purpose: The objective of this paper is to investigate how environmental improvements can be achieved through operational practices of Lean Manufacturing. Design/methodology/approach: A literature review was conducted to analyze the relationship between operational practices of Lean and reduction of environmental impact in organizational contexts. Verified theoretically, this relationship was observed in a company of the electronics industry, through an exploratory research which contemplated a mixed approach. The adopted research method consisted of a single case study, by providing greater depth and detail of the study. Utilized a research protocol, validated test pilot. The instruments for data collection were semi-structured interviews, direct observation and document analysis. The information was examined qualitatively considering the technique for content analysis. Findings: As a result of the study, it was found that there is evidence for the existence of relationship between the practices of Lean, for example, Kaizen, PDCA (plan, do, check, act, Ishikawa Diagram, Poka-Yoke, Standardized Work and Value Stream Mapping, with the reduction of environmental impacts of an organization. This reduction was observed after application of these practices that resulted in the reduction of energy consumption, water and waste generation. These results were accounted for financially, contributing to a reduction of annual costs by about US$ 20,900. Originality/value: The study presents in detail, the application of operational practices of Lean Manufacturing, with an effective view to reducing the environmental impact and cost reduction. The literature review, a detailed description of the application process and financial results are important information that contributes to the scientific studies that address traditional operating practices and the search for better environmental performance.

Operational practices of lean manufacturing: Potentiating environmental improvements

Energy Technology Data Exchange (ETDEWEB)

Pinto, Marcos José Alves Junior; Mendes, Juliana Veiga

2017-07-01

Purpose: The objective of this paper is to investigate how environmental improvements can be achieved through operational practices of Lean Manufacturing. Design/methodology/approach: A literature review was conducted to analyze the relationship between operational practices of Lean and reduction of environmental impact in organizational contexts. Verified theoretically, this relationship was observed in a company of the electronics industry, through an exploratory research which contemplated a mixed approach. The adopted research method consisted of a single case study, by providing greater depth and detail of the study. Utilized a research protocol, validated test pilot. The instruments for data collection were semi-structured interviews, direct observation and document analysis. The information was examined qualitatively considering the technique for content analysis. Findings: As a result of the study, it was found that there is evidence for the existence of relationship between the practices of Lean, for example, Kaizen, PDCA (plan, do, check, act), Ishikawa Diagram, Poka-Yoke, Standardized Work and Value Stream Mapping, with the reduction of environmental impacts of an organization. This reduction was observed after application of these practices that resulted in the reduction of energy consumption, water and waste generation. These results were accounted for financially, contributing to a reduction of annual costs by about US$ 20,900. Originality/value: The study presents in detail, the application of operational practices of Lean Manufacturing, with an effective view to reducing the environmental impact and cost reduction. The literature review, a detailed description of the application process and financial results are important information that contributes to the scientific studies that address traditional operating practices and the search for better environmental performance.

Operational practices of lean manufacturing: Potentiating environmental improvements

International Nuclear Information System (INIS)

Pinto, Marcos José Alves Junior; Mendes, Juliana Veiga

2017-01-01

Purpose: The objective of this paper is to investigate how environmental improvements can be achieved through operational practices of Lean Manufacturing. Design/methodology/approach: A literature review was conducted to analyze the relationship between operational practices of Lean and reduction of environmental impact in organizational contexts. Verified theoretically, this relationship was observed in a company of the electronics industry, through an exploratory research which contemplated a mixed approach. The adopted research method consisted of a single case study, by providing greater depth and detail of the study. Utilized a research protocol, validated test pilot. The instruments for data collection were semi-structured interviews, direct observation and document analysis. The information was examined qualitatively considering the technique for content analysis. Findings: As a result of the study, it was found that there is evidence for the existence of relationship between the practices of Lean, for example, Kaizen, PDCA (plan, do, check, act), Ishikawa Diagram, Poka-Yoke, Standardized Work and Value Stream Mapping, with the reduction of environmental impacts of an organization. This reduction was observed after application of these practices that resulted in the reduction of energy consumption, water and waste generation. These results were accounted for financially, contributing to a reduction of annual costs by about US$ 20,900. Originality/value: The study presents in detail, the application of operational practices of Lean Manufacturing, with an effective view to reducing the environmental impact and cost reduction. The literature review, a detailed description of the application process and financial results are important information that contributes to the scientific studies that address traditional operating practices and the search for better environmental performance.

Lean Manufacturing e Lean Accounting Cost: um enfoque no real desempenho em empresas de capital aberto na BOVESPA

OpenAIRE

Teixeira, Hipólito Francisco

2016-01-01

Esta pesquisa teve por alvo o campo de estudo denominado Lean Accounting (LA) aplicado as empresas que adotam os procedimentos de Produção Enxuta (PE). As empresas neste ambiente competitivo e muito imprevisivel têm procuradoadotar decisões e procedimentos voltadosa valorizar sua própria continuidade e diferencial para se expor perante ao mercado. Neste sentido novas tecnologias de produção e controles contábeis são necessários. Lean Accounting (LA) ou Contabilidade Lean ou “enxuta” pode s...

Assessment of gut microbiota populations in lean and obese Zucker rats.

Directory of Open Access Journals (Sweden)

Reza Hakkak

Full Text Available Obesity has been on the rise in the US and worldwide for the last several decades. Obesity has been associated with chronic disease development, such as certain types of cancer, type 2 diabetes, cardiovascular disease, and liver diseases. Previously, we reported that obesity promotes DMBA-induced mammary tumor development using the obese Zucker rat model. The intestinal microbiota is composed of a diverse population of obligate and facultative anaerobic microorganisms, and these organisms carry out a broad range of metabolic activities. Obesity has been linked to changes in the intestinal microbiota, but the composition of the bacterial populations in lean and obese Zucker rats has not been carefully studied. Therefore, the objective of this study was to determine the effects of obesity on the gut microbiota in this model. Lean and obese female Zucker rats (n = 16 were fed an AIN-93G-like diet for 8 weeks. Rats were weighed twice weekly, and fecal samples were collected at the beginning and end of the experiment. 16S rRNA gene sequencing was used to evaluate the composition of the fecal bacterial populations. At the outset of the study, the lean rats exhibited much lower ratios of the Firmicutes to Bacteroidetes phyla than the obese rats, but after 60 days, this ratio in the lean rats exceeded that of the obese. This shift was associated with reductions in the Bacteroidaceae, S24-7 and Paraprevotellaceae families in the lean rats. Obese rats also showed increased levels of the genus Akkermansia at day 60. PCoA plots of beta diversity showed clustering of the different test groups, indicating clear differences in intestinal microbiota populations associated with both the time point of the study and the lean or obese status in the Zucker rat model for obesity.

Substance use and misuse in burn patients: Testing the classical hypotheses of the interaction between post-traumatic symptomatology and substance use.

Science.gov (United States)

Eiroa-Orosa, Francisco Jose; Giannoni-Pastor, Anna; Fidel-Kinori, Sara Guila; Argüello, José María

2016-01-01

The authors aimed to test whether the three classical hypotheses of the interaction between post-traumatic symptomatology and substance use (high risk of trauma exposure, susceptibility for post-traumatic symptomatology, and self-medication of symptoms), may be useful in the understanding of substance use among burn patients. Substance use data (nicotine, alcohol, cannabis, amphetamines, cocaine, opiates, and tranquilizers) and psychopathology measures among burn patients admitted to a burn unit and enrolled in a longitudinal observational study were analyzed. Lifetime substance use information (n = 246) was incorporated to analyses aiming to test the high risk hypothesis. Only patients assessed for psychopathology in a 6-month follow-up (n = 183) were included in prospective analyses testing the susceptibility and self-medication hypotheses. Regarding the high risk hypothesis, results show a higher proportion of heroin and tranquilizer users compared to the general population. Furthermore, in line with the susceptibility hypothesis, higher levels of symptomatology were found in lifetime alcohol, tobacco, and drug users during recovery. The self-medication hypothesis could be tested partially due to the hospital stay "cleaning" effect, but severity of symptoms was linked to the amount of caffeine, nicotine, alcohol, and cannabis use after discharge. It was found that the 3 classical hypotheses could be used to understand the link between traumatic experiences and substance use explaining different patterns of burn patient's risk for trauma exposure and emergence of symptomatology.

Enhancing Lean Manufacturing Learning Experience through Hands-On Simulation

Science.gov (United States)

Elbadawi, Isam; McWilliams, Douglas L.; Tetteh, Edem G.

2010-01-01

Finding appropriate interactive exercises to increase students' learning in technical topic courses is always challenging to educators. In this study, several paper plane hands-on simulation exercises were developed, used, and tested in a lean manufacturing course for beginning college students. A pretest and posttest was used to assess the…

Lean Construction Supply Chain : A Literature Review

OpenAIRE

Ren, Jiamei

2012-01-01

The aim of this thesis is to enhance the management of supply systems in construction industry using lean principles. This study is an attempt to identify what kind of activities causes’ construction process delay and how to perform lean concept into supply chain in practice. The objective is to assure on-time delivery of information and materials to construction sites at lowest cost and maximum value for the customer. These study problems have been analysed from a lean construction supply ch...

Optimization of large scale food production using Lean Manufacturing principles

DEFF Research Database (Denmark)

Engelund, Eva Høy; Friis, Alan; Breum, Gitte

2009-01-01

This paper discusses how the production principles of Lean Manufacturing (Lean) can be applied in a large-scale meal production. Lean principles are briefly presented, followed by a field study of how a kitchen at a Danish hospital has implemented Lean in the daily production. In the kitchen...... not be negatively affected by the rationalisation of production procedures. The field study shows that Lean principles can be applied in meal production and can result in increased production efficiency and systematic improvement of product quality without negative effects on the working environment. The results...... show that Lean can be applied and used to manage the production of meals in the kitchen....

High burn rate solid composite propellants

Science.gov (United States)

Manship, Timothy D.

High burn rate propellants help maintain high levels of thrust without requiring complex, high surface area grain geometries. Utilizing high burn rate propellants allows for simplified grain geometries that not only make production of the grains easier, but the simplified grains tend to have better mechanical strength, which is important in missiles undergoing high-g accelerations. Additionally, high burn rate propellants allow for a higher volumetric loading which reduces the overall missile's size and weight. The purpose of this study is to present methods of achieving a high burn rate propellant and to develop a composite propellant formulation that burns at 1.5 inches per second at 1000 psia. In this study, several means of achieving a high burn rate propellant were presented. In addition, several candidate approaches were evaluated using the Kepner-Tregoe method with hydroxyl terminated polybutadiene (HTPB)-based propellants using burn rate modifiers and dicyclopentadiene (DCPD)-based propellants being selected for further evaluation. Propellants with varying levels of nano-aluminum, nano-iron oxide, FeBTA, and overall solids loading were produced using the HTPB binder and evaluated in order to determine the effect the various ingredients have on the burn rate and to find a formulation that provides the burn rate desired. Experiments were conducted to compare the burn rates of propellants using the binders HTPB and DCPD. The DCPD formulation matched that of the baseline HTPB mix. Finally, GAP-plasticized DCPD gumstock dogbones were attempted to be made for mechanical evaluation. Results from the study show that nano-additives have a substantial effect on propellant burn rate with nano-iron oxide having the largest influence. Of the formulations tested, the highest burn rate was a 84% solids loading mix using nano-aluminum nano-iron oxide, and ammonium perchlorate in a 3:1(20 micron: 200 micron) ratio which achieved a burn rate of 1.2 inches per second at 1000

The role of resilience in the recovery of the burn-injured patient: an integrative review

Directory of Open Access Journals (Sweden)

Kornhaber R

2016-05-01

Full Text Available R Kornhaber,1 H Bridgman,2 L McLean,3–6 J Vandervord7 1School of Health Sciences, Faculty of Health, University of Tasmania, Hobart, TAS, 2Centre for Rural Health, School of Health Sciences, Faculty of Health, University of Tasmania, Hobart, TAS, 3Brain and Mind Centre, 4Westmead Psychotherapy Program, Discipline of Psychiatry, Sydney Medical School, University of Sydney, Sydney, NSW, 5Sydney West and Greater Southern Psychiatry Training Network, Cumberland Hospital, Western Sydney Local Health District, Sydney, NSW, 6Consultation-Liaison Psychiatry, Royal North Shore Hospital, Sydney, NSW, 7Severe Burns Injury Unit, Royal North Shore Hospital, St Leonards, NSW, Australia Abstract: Severe burn injuries are catastrophic life events resulting in significant physical and psychological effects. With long periods of hospitalization and rehabilitation, burn survivors encounter many issues, including an altered body image and loss of function and independence that subsequently influence quality of life and the family unit. Consequently, resilience has been identified as a fundamental concept that facilitates the adaptability required to navigate the lengthy and complex recovery process. However, over time, the notion of resilience has shifted from a static, innate trait to a fluid and multidimensional concept. Here, we review the evidence surrounding the role of resilience in the recovery of burn injury. This integrative review was based on a systematic search of five electronic databases. Of the 89 articles identified, ten primary research papers met the inclusion criteria. Three key themes were identified encompassing relational strengths, positive coping, and the resistance to trauma symptoms that are fundamental constructs associated with developing and sustaining resilience that resonate with the broader literature on burn recovery. However, limited evidence is currently available within the burns context. While resilience appears to be a vital

Lean computing for the cloud

CERN Document Server

Bauer, Eric

2016-01-01

Applies lean manufacturing principles across the cloud service delivery chain to enable application and infrastructure service providers to sustainably achieve the shortest lead time, best quality, and value This book focuses on lean in the context of cloud computing capacity management of applications and the physical and virtual cloud resources that support them. Lean Computing for the Cloud considers business, architectural and operational aspects of efficiently delivering valuable services to end users via cloud-based applications hosted on shared cloud infrastructure. The work also focuses on overall optimization of the service delivery chain to enable both application service and infrastructure service providers to adopt leaner, demand driven operations to serve end users more efficiently. The book’s early chapters analyze how capacity management morphs with cloud computing into interlocked physical infrastructure capacity management, virtual resou ce capacity management, and application capacity ma...

Aquifer pumping test report for the burn site groundwater area of concern

Energy Technology Data Exchange (ETDEWEB)

Skelly, Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ferry, Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-12-01

The Aquifer Pumping Test Report for the Burn Site Groundwater (BSG) Area of Concern is being submitted by National Technology and Engineering Solutions of Sandia, LLC and the U.S. Department of Energy (DOE)/National Nuclear Security Administration to describe the results of the aquifer pumping test program and related field activities that were completed at the BSG Area of Concern. This report summarizes the results of the field work and data analyses, and is being submitted to the New Mexico Environment Department (NMED) Hazardous Waste Bureau, as required by the April 14, 2016 letter, Summary of Agreements and Proposed Milestones Pursuant to the Meeting of July 20, 2015, (NMED April 2016).

Dietary B vitamin needs of strains of pigs with high and moderate lean growth.

Science.gov (United States)

Stahly, T S; Williams, N H; Lutz, T R; Ewan, R C; Swenson, S G

2007-01-01

Ten sets of 5 littermate pigs from each of 2 genetic strains were utilized to determine the impact of the dietary concentration of 5 B vitamins (riboflavin, niacin, pantothenic acid, cobalamin, and folacin) on growth from 9 to 28 kg of BW in pigs with high or moderate capacity for lean growth. All pigs (penned individually) were reared via a segregated, early weaning scheme, so that the lean growth potential of each strain could be expressed. The basal diet provided the 5 test vitamins at concentrations of total and estimated bioavailability equivalent to a minimum of 100 and 70%, respectively, of their estimated requirements (NRC, 1998) for 5- to 10-kg pigs. At a BW of 9 +/- 0.9 kg, pigs within each litter were allotted to the basal diet supplemented with sources of the 5 test vitamins equivalent to an additional 0, 100, 200, 300, or 400% (bioavailable) of the NRC requirements. Pigs from the high lean strain consumed less feed (P vitamin concentrations were increased. However, the dietary B vitamin concentrations needed to optimize G:F were greater (P 470% of NRC, 1998) vs. moderate (270%) lean strain. Based on these data, the dietary needs for 1 or more of the 5 B vitamins are greater than current NRC (1998) estimates, particularly in pigs expressing a high rate of lean tissue growth. The greater need for these vitamins is not associated with greater dietary energy intake or body energy accretion rate but is potentially due to shifts in the predominant metabolic pathways.

Investigating employee resistance to Lean transformation: UK case study.

OpenAIRE

Bruce, J.; Scott, Philip; Roberts, Martyn

2011-01-01

Lean is a business process transformation approach that eliminates ‘wastes’ – activities that generate no value for the customer. Lean originated from the production line but is widely implemented in the service sector. This study investigates human and social factors in a Lean transformation in a ‘knowledge worker’ environment. We identify a paradox: a successful Lean programme in the service sector develops staff who are educated and empowered and thus potential opponents to future business...

Surgical management and hypermetabolic modulation of pediatric burns

NARCIS (Netherlands)

Barret Nerín, Juan Pedro

2002-01-01

The purpose of the present thesis is to test the hypothesis that immediate burn wound excision of massive pediatric burns is safe and efficacious, presenting with negligible postoperative complications and with salutary effects on the inflammatory and catabolic response after burn injury.

The evolution of Lean organizations

OpenAIRE

Serafinas, Dalius; Ruželė, Darius

2014-01-01

Remiantis evoliucijos tyrimų modeliais bei autorių sudarytu evoliucionuojančios organizacijos modeliu,straipsnyje analizuojama Lean vadybos metodologija ir tiriama, kaip evoliucionuoja ją įgyvendinančios Lietuvosgamybinės organizacijos. The purpose of this paper is to examine the evolution of Lean organizations.Design/methodology/approach: a conceptual literature on the evolution of species, organisms and organizations was reviewed and an original model (framework) of the evolution of orga...

Accelerant-related burns and drug abuse: Challenging combination.

Science.gov (United States)

Leung, Leslie T F; Papp, Anthony

2018-05-01

Accelerants are flammable substances that may cause explosion when added to existing fires. The relationships between drug abuse and accelerant-related burns are not well elucidated in the literature. Of these burns, a portion is related to drug manufacturing, which have been shown to be associated with increased burn complications. 1) To evaluate the demographics and clinical outcomes of accelerant-related burns in a Provincial Burn Centre. 2) To compare the clinical outcomes with a control group of non-accelerant related burns. 3) To analyze a subgroup of patients with history of drug abuse and drug manufacturing. Retrospective case control study. Patient data associated with accelerant-related burns from 2009 to 2014 were obtained from the British Columbia Burn Registry. These patients were compared with a control group of non-accelerant related burns. Clinical outcomes that were evaluated include inhalational injury, ICU length of stay, ventilator support, surgeries needed, and burn complications. Chi-square test was used to evaluate categorical data and Student's t-test was used to evaluate mean quantitative data with the p value set at 0.05. A logistic regression model was used to evaluate factors affecting burn complications. Accelerant-related burns represented 28.2% of all burn admissions (N=532) from 2009 to 2014. The accelerant group had higher percentage of patients with history of drug abuse and was associated with higher TBSA burns, ventilator support, ICU stay and pneumonia rates compared to the non-accelerant group. Within the accelerant group, there was no difference in clinical outcomes amongst people with or without history of drug abuse. Four cases were associated with methamphetamine manufacturing, all of which underwent ICU stay and ventilator support. Accelerant-related burns cause significant burden to the burn center. A significant proportion of these patients have history of drug abuse. Copyright © 2017 Elsevier Ltd and ISBI. All rights

Improving preanalytic processes using the principles of lean production (Toyota Production System).

Science.gov (United States)

Persoon, Thomas J; Zaleski, Sue; Frerichs, Janice

2006-01-01

The basic technologies used in preanalytic processes for chemistry tests have been mature for a long time, and improvements in preanalytic processes have lagged behind improvements in analytic and postanalytic processes. We describe our successful efforts to improve chemistry test turnaround time from a central laboratory by improving preanalytic processes, using existing resources and the principles of lean production. Our goal is to report 80% of chemistry tests in less than 1 hour and to no longer recognize a distinction between expedited and routine testing. We used principles of lean production (the Toyota Production System) to redesign preanalytic processes. The redesigned preanalytic process has fewer steps and uses 1-piece flow to move blood samples through the accessioning, centrifugation, and aliquoting processes. Median preanalytic processing time was reduced from 29 to 19 minutes, and the laboratory met the goal of reporting 80% of chemistry results in less than 1 hour for 11 consecutive months.

Lean six sigma methodologies improve clinical laboratory efficiency and reduce turnaround times.

Science.gov (United States)

Inal, Tamer C; Goruroglu Ozturk, Ozlem; Kibar, Filiz; Cetiner, Salih; Matyar, Selcuk; Daglioglu, Gulcin; Yaman, Akgun

2018-01-01

Organizing work flow is a major task of laboratory management. Recently, clinical laboratories have started to adopt methodologies such as Lean Six Sigma and some successful implementations have been reported. This study used Lean Six Sigma to simplify the laboratory work process and decrease the turnaround time by eliminating non-value-adding steps. The five-stage Six Sigma system known as define, measure, analyze, improve, and control (DMAIC) is used to identify and solve problems. The laboratory turnaround time for individual tests, total delay time in the sample reception area, and percentage of steps involving risks of medical errors and biological hazards in the overall process are measured. The pre-analytical process in the reception area was improved by eliminating 3 h and 22.5 min of non-value-adding work. Turnaround time also improved for stat samples from 68 to 59 min after applying Lean. Steps prone to medical errors and posing potential biological hazards to receptionists were reduced from 30% to 3%. Successful implementation of Lean Six Sigma significantly improved all of the selected performance metrics. This quality-improvement methodology has the potential to significantly improve clinical laboratories. © 2017 Wiley Periodicals, Inc.

LEAN THINKING IN HEALTHCARE: REVIEW OF IMPLEMENTATION RESULTS

Directory of Open Access Journals (Sweden)

Marija Kovacevic

2016-03-01

Full Text Available For over decade, automotive industry originated lean concept has been successfully implemented in healthcare systems as a management method and philosophy with main focus on elimination of all types of wastes and looses in all tasks and processes so that time, materials, resources and medical procedures could be realized as effectively as it is possible. As main result lean concept implementation ensured to healthcare organizations to focus on their main core function and dedicate more time and efforts to patients without additional costs for them or healthcare system. However, lean implementation in healthcare could be much more difficult than in standard industrial environment and there are significant number of examples of lean in healthcare projects that failed to gain any measurable results and sustainable benefits from it. This paper presents review of some of the most successful implementations of lean tools and principles in healthcare organizations.

The application of lean principles in product development

DEFF Research Database (Denmark)

Bjarnø, Ole-Christian

2007-01-01

Although Lean Manufacturing has been a megatrend for several years, its principles have not been broadly applied in product development processes. We have therefore found it useful to look into the theories of lean manufacturing and to discuss how and to what extent they could be applied in the p......Although Lean Manufacturing has been a megatrend for several years, its principles have not been broadly applied in product development processes. We have therefore found it useful to look into the theories of lean manufacturing and to discuss how and to what extent they could be applied...... in the product development processes, and this study is compared with industrial practices in several front running companies in Denmark. From this research a suggestion for a framework and a tool-box for lean product development is created and discussed from a HR management, an implementation, an operational...

Lean healthcare.

Science.gov (United States)

Weinstock, Donna

2008-01-01

As healthcare organizations look for new and improved ways to reduce costs and still offer quality healthcare, many are turning to the Toyota Production System of doing business. Rather than focusing on cutting personnel and assets, "lean healthcare" looks to improve patient satisfaction through improved actions and processes.

Improving ED specimen TAT using Lean Six Sigma.

Science.gov (United States)

Sanders, Janet H; Karr, Tedd

2015-01-01

Lean and Six Sigma are continuous improvement methodologies that have garnered international fame for improving manufacturing and service processes. Increasingly these methodologies are demonstrating their power to also improve healthcare processes. The purpose of this paper is to discuss a case study for the application of Lean and Six Sigma tools in the reduction of turnaround time (TAT) for Emergency Department (ED) specimens. This application of the scientific methodologies uncovered opportunities to improve the entire ED to lab system for the specimens. This case study provides details on the completion of a Lean Six Sigma project in a 1,000 bed tertiary care teaching hospital. Six Sigma's Define, Measure, Analyze, Improve, and Control methodology is very similar to good medical practice: first, relevant information is obtained and assembled; second, a careful and thorough diagnosis is completed; third, a treatment is proposed and implemented; and fourth, checks are made to determine if the treatment was effective. Lean's primary goal is to do more with less work and waste. The Lean methodology was used to identify and eliminate waste through rapid implementation of change. The initial focus of this project was the reduction of turn-around-times for ED specimens. However, the results led to better processes for both the internal and external customers of this and other processes. The project results included: a 50 percent decrease in vials used for testing, a 50 percent decrease in unused or extra specimens, a 90 percent decrease in ED specimens without orders, a 30 percent decrease in complete blood count analysis (CBCA) Median TAT, a 50 percent decrease in CBCA TAT Variation, a 10 percent decrease in Troponin TAT Variation, a 18.2 percent decrease in URPN TAT Variation, and a 2-5 minute decrease in ED registered nurses rainbow draw time. This case study demonstrated how the quantitative power of Six Sigma and the speed of Lean worked in harmony to improve

[Influence of three-level collaboration network of pediatric burns treatment in Anhui province on treatment effects of burn children].

Science.gov (United States)

Xia, Z G; Zhou, X L; Kong, W C; Li, X Z; Song, J H; Fang, L S; Hu, D L; Cai, C; Tang, Y Z; Yu, Y X; Wang, C H; Xu, Q L

2018-03-20

Objective: To explore the influence of three-level collaboration network of pediatric burns in Anhui province on treatment effects of burn children. Methods: The data of medical records of pediatric burn children transferred from Lu'an People's Hospital and Fuyang People's Hospital to the First Affiliated Hospital of Anhui Medical University from January 2014 to December 2015 and January 2016 to September 2017 (before and after establishing three-level collaboration network of pediatric burns treatment) were analyzed: percentage of transferred burn children to hospitalized burn children in corresponding period, gender, age, burn degree, treatment method, treatment result, occurrence and treatment result of shock, and operative and non-operative treatment time and cost. Rehabilitation result of burn children transferred back to local hospitals in 2016 and 2017. Data were processed with t test, chi-square test, Mann-Whitney U test, and Fisher's exact test. Results: (1) Percentage of burn children transferred from January 2014 to December 2015 was 34.3% (291/848) of the total number of hospitalized burn children in the same period of time, which was close to 30.4% (210/691) of burn children transferred from January 2016 to September 2017 ( χ (2)=2.672, P >0.05). (2) Gender, age, burn degree, and treatment method of burn children transferred from the two periods of time were close ( χ (2)=3.382, Z =-1.917, -1.911, χ (2)=3.133, P >0.05). (3) Cure rates of children with mild, moderate, and severe burns transferred from January 2016 to September 2017 were significantly higher than those of burn children transferred from January 2014 to December 2015 ( χ (2)=11.777, 6.948, 4.310, P burns transferred from the two periods of time were close ( χ (2)=1.181, P >0.05). (4) Children with mild and moderate burns transferred from the two periods of time were with no shock. The incidence of shock of children with severe burns transferred from January 2014 to December 2015 was 6

Experienced Barriers to Lean in Swedish Manufacturing and Health Care

Directory of Open Access Journals (Sweden)

Bengt Halling

2013-12-01

Full Text Available The purpose is to compare similarities and divergences in how the concepts of Lean and barriers to Lean are described by key informants at a production unit in a large manufacturing company and two emergency health care units in Sweden. Data was collected via semi-structured interviews and analyzed with the constant comparative method (CCM and Porras and Robertson’s (1992 change model. : In both organizations, the view of Lean changed from a toolbox to a human behavior view. Eight barriers were experienced in both organizations. Three barriers were unique to manufacturing or to health care, respectively. Nine barriers were elements of social factors; five were elements of organizing arrangements. Only people practically involved and responsible for the implementation at the two organizations participated in the study. Persons responsible for implementing Lean should consider organizational arrangements and social factors in order to limit barriers to successful implementation. Most research on Lean has been about successful Lean implementations. This study focuses on how Lean is viewed and what barriers personnel in manufacturing and health care have experienced. In comparing the barriers to Lean experienced in the two groups, common, archetypical, and unique barriers for manufacturing and health care can be identified, thus contributing to knowledge about barriers to Lean implementation.

How does lean work in emergency care? A case study of a lean-inspired intervention at the Astrid Lindgren Children's hospital, Stockholm, Sweden.

Science.gov (United States)

Mazzocato, Pamela; Holden, Richard J; Brommels, Mats; Aronsson, Håkan; Bäckman, Ulrika; Elg, Mattias; Thor, Johan

2012-02-01

There is growing interest in applying lean thinking in healthcare, yet, there is still limited knowledge of how and why lean interventions succeed (or fail). To address this gap, this in-depth case study examines a lean-inspired intervention in a Swedish pediatric Accident and Emergency department. We used a mixed methods explanatory single case study design. Hospital performance data were analyzed using analysis of variance (ANOVA) and statistical process control techniques to assess changes in performance one year before and two years after the intervention. We collected qualitative data through non-participant observations, semi-structured interviews, and internal documents to describe the process and content of the lean intervention. We then analyzed empirical findings using four theoretical lean principles (Spear and Bowen 1999) to understand how and why the intervention worked in its local context as well as to identify its strengths and weaknesses. Improvements in waiting and lead times (19-24%) were achieved and sustained in the two years following lean-inspired changes to employee roles, staffing and scheduling, communication and coordination, expertise, workspace layout, and problem solving. These changes resulted in improvement because they: (a) standardized work and reduced ambiguity, (b) connected people who were dependent on one another, (c) enhanced seamless, uninterrupted flow through the process, and (d) empowered staff to investigate problems and to develop countermeasures using a "scientific method". Contextual factors that may explain why not even greater improvement was achieved included: a mismatch between job tasks, licensing constraints, and competence; a perception of being monitored, and discomfort with inter-professional collaboration. Drawing on Spear and Bowen's theoretical propositions, this study explains how a package of lean-like changes translated into better care process management. It adds new knowledge regarding how lean

Use of Lean response to improve pandemic influenza surge in public health laboratories.

Science.gov (United States)

Isaac-Renton, Judith L; Chang, Yin; Prystajecky, Natalie; Petric, Martin; Mak, Annie; Abbott, Brendan; Paris, Benjamin; Decker, K C; Pittenger, Lauren; Guercio, Steven; Stott, Jeff; Miller, Joseph D

2012-01-01

A novel influenza A (H1N1) virus detected in April 2009 rapidly spread around the world. North American provincial and state laboratories have well-defined roles and responsibilities, including providing accurate, timely test results for patients and information for regional public health and other decision makers. We used the multidisciplinary response and rapid implementation of process changes based on Lean methods at the provincial public health laboratory in British Columbia, Canada, to improve laboratory surge capacity in the 2009 influenza pandemic. Observed and computer simulating evaluation results from rapid processes changes showed that use of Lean tools successfully expanded surge capacity, which enabled response to the 10-fold increase in testing demands.

Six sigma and lean production adoption in a manufacturing company

Directory of Open Access Journals (Sweden)

Alisson Christian Scheller

2014-11-01

Full Text Available The connection among Lean Production with Six Sigma originated the Lean Six Sigma methodology, focused on processes variation and waste reduction. This methodology was developed on different ways in the companies and there is no consensus over its structure and its implementation. In this context, this paper aims to identify and analyze the main characteristics on the adoption and integration of Lean Six Sigma methodology through a case study conducted in a manufacturing company that adopts lean production and six sigma. The results show two important aspects of the Lean Six Sigma methodology. One of them is the adoption of the value stream mapping as a central tool on Lean Six Sigma. The other is the use of DMAIC for improvements actions. The study indicates that despite the difficulties on Lean Six Sigma implementation, the methodology offers benefits to the company that adopts it in the suitable way.

Product innovation and commercialization in lean global start-ups

DEFF Research Database (Denmark)

Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

2015-01-01

The paper examines the distinctive characteristics of product innovation and commercialization in Lean Global Start-up (LGS) – new technology firms which have adopted a lean and global path from or near to their inception. It suggests an uncertainty vs risk framework which allows integrating two...... research streams – Born Global (BG) firms and lean start-ups. In addition to its integrative theoretical value, the paper offers insights for lean start-up managers dealing with the challenges of a global start....

Using Lean to Advance Quality Improvement Research.

Science.gov (United States)

Blackmore, Christopher Craig; Williams, Barbara L; Ching, Joan M; Chafetz, Lynne A; Kaplan, Gary S

2016-01-01

Quality improvement research skills are not commonplace among quality improvement practitioners, and research on the effectiveness of quality improvement has not always kept pace with improvement innovation. However, the Lean tools applied to quality improvement should be equally relevant to the advancement of quality improvement research. We applied the Lean methods to develop a simplified quality improvement publication pathway enabling a small research methodology group to increase quality improvement research throughout the institution. The key innovations of the pathway are horizontal integration of the quality improvement research methods group across the institution, implementation of a Lean quality improvement research pathway, and application of a just-in-time quality improvement research toolkit. This work provides a road map and tools for the acceleration of quality improvement research. At our institution, the Lean quality improvement research approach was associated with statistically significant increases in the number (annual mean increase from 3.0 to 8.5, p = .03) and breadth of published quality improvement research articles, and in the number of quality improvement research projects currently in process. Application of Lean methods to the quality improvement research process can aid in increasing publication of quality improvement articles from across the institution.

How is the chlorophyll count affected by burned and unburned marsh areas?

Science.gov (United States)

Kendrick, C.

2017-12-01

Does marsh burnings, either man made or natural, hinder or help Louisiana's vitally important coastal plant life? Does the carbon produced from the fires have a negative effect on the chlorophyll count of these precious living protective barriers? Or does it help contribute to raising the plants chlorophyll count? Along Louisiana's Gulf Coast, marsh burnings are conducted every 2-4 years to destroy some of the Spartina patens. Fires and smoke may have an effect on the chlorophyll count of the plants found in Louisiana's marshes. Peat burns, root burns, and cover burns are the three types of marsh fires. These burns can be either man made or started by natural causes. Peat burns occur when the soil is dry due to a drained marsh. Root burns occur when plant roots are burned without the soil being consumed. Cover burns occur when several centimeters of water covers the soil. Cover burns are often used by Wildlife and Fisheries personnel to promote preferred plant food growth like Scirpus olneyi rather than the dominant Spartina patens. Our project was conducted by testing marsh plants and obtaining chlorophyll count of both a burned (cover burn) and an unburned area. Approximately one year after the burn, in August 2015, we tested the burned area's site. We retested the same site in December 2016. The results from our testing showed that there was a slightly higher chlorophyll count in the burned area. The chlorophyll count average from the two testing days was 33.5 in the burned area and 30.15 in the unburned area. Our hypothesis was that the chlorophyll content of "controlled" burned wetland areas will have a higher amount than the "no" burn area. The experiment results supported this hypothesis by showing an increase of 3.35 average in the burned area.

Accuracy of Body Mass Index Versus Lean Mass Index for Prediction of Sarcopenia in Older Women.

Science.gov (United States)

Benton, M J; Silva-Smith, A L

2018-01-01

We compared accuracy of body mass index (BMI) versus lean mass index (LMI) to predict sarcopenia in 58 community-dwelling women (74.1±0.9 years). Lean mass was measured with multi-frequency bioelectrical impedance analysis, and strength was measured with Arm Curl test, Chair Stand test, and handgrip dynamometry. Sarcopenia was defined as low LMI. When categorized by BMI, normal women had less absolute lean mass (37.6±1.0 vs. 42.6±0.9 kg; Plean mass (14.1±0.2 vs. 16.1±0.2 kg/m2; Plean mass (44.0±0.7 vs. 35.7±0.7 kg; Plean mass (16.2±0.2 vs. 13.8±0.2 kg/m2; Plean mass and strength. For clinical assessment, calculation of LMI rather than BMI is appropriate.

Stress disorder and PTSD after burn injuries: a prospective study of predictors of PTSD at Sina Burn Center, Iran

Directory of Open Access Journals (Sweden)

Sadeghi-Bazargani H

2011-07-01

Full Text Available Homayoun Sadeghi-Bazargani1, Hemmat Maghsoudi2, Mohsen Soudmand-Niri3, Fatemeh Ranjbar4, Hossein Mashadi-Abdollahi51Neuroscience Research Center, Statistics and Epidemiology Department, School of Health and Nutrition, 2Department of Surgery, 3School of Psychology, 4Department of Psychiatry, 5National Public Health Management Centre, Tabriz University of Medical Sciences, Tabriz, IranBackground: A burn injury can be a traumatic experience with tremendous social, physical, and psychological consequences. The aim of this study was to investigate the existence of post-traumatic stress disorder (PTSD and predictors of PTSD Checklist score initially and 3 months after injury in burns victims admitted to the Sina Burn Center in north-west Iran.Methods: This prospective study examined adult patients aged 16–65 years with unintentional burns. The PTSD Checklist was used to screen for PTSD.Results: Flame burns constituted 49.4% of all burns. Mean PTSD score was 23.8 ± 14.7 early in the hospitalization period and increased to 24.2 ± 14.3, 3 months after the burn injury. Twenty percent of victims 2 weeks into treatment had a positive PTSD screening test, and this figure increased to 31.5% after 3 months. The likelihood of developing a positive PTSD screening test increased significantly after 3 months (P < 0.01. Using multivariate regression analysis, factors independently predicting PTSD score were found to be age, gender, and percentage of total body surface area burned.Conclusion: PTSD was a problem in the population studied and should be managed appropriately after hospital admission due to burn injury. Male gender, younger age, and higher total body surface area burned may predict a higher PTSD score after burn injury. Keywords: post-traumatic stress disorder, burn injury, predictors, Iran

Is there a lean future for global startups?

DEFF Research Database (Denmark)

Tanev, Stoyan

2017-01-01

This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing on gl......-based global startup research and practice. The analysis should benefit both researchers and practitioners in technology entrepreneurship, international entrepreneurship, and global innovation management.......This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing...... on global startups, and further substantiates the articulation of the need for considering the lean global startup as a new type of firm. The main message is that the lessons learned from the emergence of lean startup entrepreneurship offer a basis for promoting a similar lean phase in technology...

Lean Manufacturing Auto Cluster at Chennai

Science.gov (United States)

Bhaskaran, E.

2012-10-01

Due the presence of lot of automotive Industry, Chennai is known as Detroit of India, that producing over 40 % of the Indian vehicle and components. Lean manufacturing concepts have been widely recognized as an important tool in improving the competitiveness of industries. This is a continuous process involving everyone, starting from management to the shop floor. Automotive Component Industries (ACIs) in Ambattur Industrial Estate, Chennai has formed special purpose vehicle (SPV) society namely Ambattur Industrial Estate Manufacturers Association (AIEMA) Technology Centre (ATC) lean manufacturing cluster (ATC-LMC) during July 2010 under lean manufacturing competitiveness scheme, that comes under National Manufacturing Competitiveness Programme of Government of India. The Tripartite Agreement is taken place between National Productivity Council, consultants and cluster (ATC-LMC). The objective is to conduct diagnostic study, study on training and application of various lean manufacturing techniques and auditing in ten ACIs. The methodology adopted is collection of primary data/details from ten ACIs. In the first phase, diagnostic study is done and the areas for improvement in each of the cluster member companies are identified. In the second phase, training programs and implementation is done on 5S and other areas. In the third phase auditing is done and found that the lean manufacturing techniques implementation in ATC-LMC is sustainable and successful in every cluster companies, which will not only enhance competitiveness but also decrease cost, time and increase productivity. The technical efficiency of LMC companies also increases significantly.

Methodological contribution to lean office implementation applied to a supply chain department : longitudinal case study analysis in a supply company of the health sector

OpenAIRE

Reinhard , Eric

2017-01-01

Like most industrial companies, the Paul Hartmann company firstly deployed the Lean approach in factories. The implementation of Lean Office basic principles is decided through the Office Excellence method (Kugel, 2010) in the procurement support department. This method applied in some major German companies since 2002 has not been scientifically tested yet. Our research aims at testing this method with a unique case study approach and evaluating its completeness in comparison to the Lean Off...

Identification of Lean Implementation Hurdles in Indian Industries

OpenAIRE

Bhim Singh

2016-01-01

Due to increased pressure from global competitors, manufacturing organizations are switching over to lean philosophies from traditional mass production. Lean manufacturing is a manufacturing philosophy which focuses on elimination of various types of wastes and creates maximum value for the end customers. Lean thinking aims to produce high quality products and services at the lowest possible cost with maximum customer responsiveness. Indian Industry is facing lot of problems in this transform...

Lean process management implementation through enhanced problem solving capabilities

Directory of Open Access Journals (Sweden)

Perumal Puvanasvaran

2010-12-01

Full Text Available All Original Equipment Manufacturers (OEM organizations in Aerospace, Automotive and Electronics industries had to upgrade their functions. These organizations including suppliers and solutions providers are duty bound to improve their functions through strategic initiatives. One such initiative is Lean Process Management. Lean Process Management has proven to aid organizations in developing manufacturing and administrative management solutions and make the organization a leaner at the same time a ‘fitter’ one, achieving World Class standards in terms of production, quality, marketing, etc, etc. The issue or problem is, although a number of authors, experts, researchers have discussed the lean process management as part organization centric issues, they failed to provide an effective lean process management system. Besides the need to formulate an effective lean process as suggested by some authors, another important reason suggested is the employee’s development aspect regarding how to unlock the infinite potential of their workforce. This employee’s development is basically the problem solving capabilities of the employees while implementing the Lean through clear cutting protocols or processes of Lean Process Management. The employees need to be developed and equipped to contribute optimally to the process. Because of this scenario, the main objective of this study is to develop an employees development system which the author has acronym or trademark it as People Development System (PDS to enhance problem solving capability among its employees while implementing the lean process management there. Although, the PDS can be implemented throughout the organization, if it is implemented in a particular department in an organization, it will be feasible to study and analyze its effectiveness in-depth. So, this study documents and analyzes the implementation of Lean process in the Kitting Department of the aerospace company, ABC Company

Efficacy and efficiency of a lean cataract pathway: a comparative study.

Science.gov (United States)

van Vliet, Ellen Joan; Sermeus, Walter; van Gaalen, Claudia M; Sol, Johannes C A; Vissers, Jan M H

2010-12-01

The demand for cataract surgery is rising, calling for pathways that have good access and are cost-effective. Lean thinking is a management strategy, aimed at improving quality while reducing costs. Lean production processes are designed to identify gaps between expected and actual performance. To analyse the efficacy and efficiency of a lean cataract pathway. Lean care delivered to a prospective cohort (616 cataract patients) was compared (1) with traditional care delivered to a historical cohort (591 cataract patients) and (2) with expected lean care in the prospective cohort. To evaluate efficacy, the authors analysed how many patients received care that adhered to the lean pathway's specifications. To evaluate efficiency, the authors analysed how often patients visited the hospital and how many additional patients could access the pathway. In the lean pathway, patient visits decreased by 23%, and access to the cataract pathway increased with 42%. A 40% decrease in patient visits and a 76% increase in access could have been realised if healthcare staff would have adhered to the lean pathway's specifications. Lean pathways can realise large improvements, and still have a significant gap between expected and actual care delivery. The challenge for healthcare teams is not to improve care delivery by using lean pathways as opposed to using traditional pathways, but to strive for optimal performance by consistently adhering to the specifications of the lean pathway.

Is There a Lean Future for Global Startups?

Directory of Open Access Journals (Sweden)

Stoyan Tanev

2017-05-01

Full Text Available This article integrates insights from the latest research on the lean startup entrepreneurial method, born-global firms, and global startups. It contributes to the clarification of terminology referring to the global aspects of startups, summarizes insights from previous literature focusing on global startups, and further substantiates the articulation of the need for considering the lean global startup as a new type of firm. The main message is that the lessons learned from the emergence of lean startup entrepreneurship offer a basis for promoting a similar lean phase in technology-based global startup research and practice. The analysis should benefit both researchers and practitioners in technology entrepreneurship, international entrepreneurship, and global innovation management.

Efficient Project Delivery Using Lean Principles - An Indian Case Study

Science.gov (United States)

Kovvuri, P. Ramachandra Reddy; Sawhney, Anil; Ahuja, Ritu; Sreekumar, Aiswarya

2016-03-01

Construction industry in India is growing at a rapid pace. Along with this growth, the industry is facing numerous challenges that are making delivery of projects inefficient. Experts believe that capacity constraints in the industry need to be addressed immediately. Government has recommended `introduction of efficient technologies and modern management techniques' to increase the productivity of the industry. In this context, lean principles can act as a lever to make project delivery more efficient and provide the much needed impetus to the Indian construction sector. Around the globe lean principles are showing positive results on the projects. Project teams are reporting improvements in construction time, cost and quality along with softer benefits of enhanced collaboration, coordination and trust in project teams. Can adoption of lean principles provide similar benefits in the Indian construction sector? This research was conducted to answer this question. Using an action research approach a key lean construction tool called Last Planner System (LPS) was tested on a large Indian construction project. The work described in this work investigates the improvements achieved in project delivery by adopting LPS in Indian construction sector. Comparison in pre- and post-implementation data demonstrates increase in the certainty of work-flow and improves schedule compliance. This is measured through a simple LPS metric called percent plan complete. Explicit improvements in schedule performance are seen during 8 week LPS implementation along with implicit improvements in coordination, collaboration and trust in the project team. This work reports the findings of LPS implementation on the case study project outlining the barriers and drivers to adoption, strategies needed to ensure successful implementation and roadmap for implementation. Based on the findings the authors envision that lean construction can make project delivery more efficient in India.

Lean principles adoption in environmental management system (EMS - ISO 14001

Directory of Open Access Journals (Sweden)

Perumal Puvanasvaran

2012-12-01

Full Text Available Purpose: The purpose of this study is to examine the characteristic of the lean principles into ISO 14001 and to propose linkage of the lean principles and ISO 14001.Design/methodology/approach: To achieve the objective of the study, literature survey and quantitative research method using questionnaires survey are used.Findings and Originality/value: The findings of this study confirm that ISO 14001 certified company adopted lean production practices.  The study also proves that lean principles have positive and significant relationship with ISO 14001 EMS and the linkage can be made between lean principles and ISO 14001 to achieve Continual Improvement.Research limitations/implications: The small sizes of the sample of the participating companies are the main limitations of this study and this research mainly focuses on the manufacturing environment and services industry.Practical implications: This research show that all ISO 14001 companies do adopt at least one lean production practices and the main findings are lean principles has positive and highly significant relationship with ISO 14001 requirements.  This is because the integration of lean principles into ISO 14001 will serve practical methods for ISO14001 EMS to achieve the continual improvement.Originality/value: This research is amongst the first to study the combined lean principles with ISO 1400.  Based on the current situation, there is no integration within this two management system. 

Lean Supply Chain Planning: A Performance Evaluation through Simulation

Directory of Open Access Journals (Sweden)

Rossini Matteo

2016-01-01

Full Text Available Nowadays companies look more and more for improving their efficiency to excel in the market. At the same time, the competition has moved from firm level to whole supply chain level. Supply chain are very complex systems and lacks of coordination among their members leads to inefficiency. Supply chain planning task is to improve coordination among supply chain members. Which is the best planning solution to improve efficiency is an open issue. On the other hand, Lean approach is becoming more and more popular among managers. Lean approach is recognize as efficiency engine for production systems, but effects of Lean implementation out of single firm boundaries is not clear. This paper aims at providing a theoretical and practical starting point for Lean implementation in supply chain planning issue. To reach it, a DES simulation model of a three-echelon and multi-product supply chain has been set. Lean management is a very broad topic and this paper focuses on two principles of “pull” and “create the flow”. Kanban system and setup-time and batch-size reductions are implemented in the lean-configured supply chain to apply “pull” and “create the flow” respectively. Lean principles implementations have been analyzed and compared with other supply chain planning policies: EOQ and information sharing (Visibility. Supported by the simulation study, this paper points Lean supply chain planning is a competitive planning policies to increase efficiency.

The roles of communication process for an effective lean manufacturing implementation

OpenAIRE

Puvanasvaran, Perumal; Megat, Hamdan; Hong, Tang Sai; Razali, Muhamad Mohd.

2009-01-01

Many companies are implementing lean manufacturing concept in order to remain competitive and sustainable, however, not many of them are successful in the process due to various reasons. Communication is an important aspect of lean process in order to successfully implement lean manufacturing. This paper determines the roles of communication process in ensuring a successful implementation of leanness in manufacturing companies. All the information of lean manufacturing practice...

Lean production and business performance: influences of ...

African Journals Online (AJOL)

Hence, this study aims to examine the influence of leadership style in the implementation of lean production. Data were gathered from randomly selected Malaysian manufacturing firms. Findings reveal a positive relationship between lean production and business performance. Specifically, democratic leadership style was ...

Making of a burn unit: SOA burn center

Directory of Open Access Journals (Sweden)

Jayant Kumar Dash

2016-01-01

Full Text Available Each year in India, burn injuries account for more than 6 million hospital emergency department visits; of which many require hospitalization and are referred to specialized burn centers. There are few burn surgeons and very few burn centers in India. In our state, Odisha, there are only two burn centers to cater to more than 5000 burn victims per year. This article is an attempt to share the knowledge that I acquired while setting up a new burn unit in a private medical college of Odisha.

Experimental Study on the Burning Behavior of Pool Fires in Rooms with Different Wall Linings

DEFF Research Database (Denmark)

Poulsen, Annemarie; Jomaas, Grunde

2011-01-01

An experimental test series, comprising 10 experiments with varying pool sizes, lining materials and amounts of liquid burning, was conducted under free burn and room burn conditions. The thermal feedback from the enclosure (ISO 9705 Room Corner Test facility) enhanced the burning rate of the poo...... in the shortest time. Given the profound difference between the enclosure tests and the free burn tests and also between enclosure tests with different linings, it is recommended to show great caution if free burn tests are to be used in design fire scenarios....

LEAN SIX SIGMA – MULTIPLE CASE STUDY

Directory of Open Access Journals (Sweden)

Delvio Venanzi

2017-12-01

Full Text Available Lean Six Sigma é uma gestão focada na qualidade e desempenho produtivo em sistemas operacionais. Este artigo discute os fundamentos desta metodologia através de duas diferentes concepções de gestão, Lean Manufacturing e Six Sigma. Primeiro, o artigo explica o DMAIC (definir, medir, analisar, melhorar e controlar e suas respectivas fases, após a filosofia Lean com o sipoc e técnicas de mapeamento de fluxo de valor. O artigo pretende mostrar a integração destes dois conceitos e seus resultados. A metodologia consistiu em uma teoria baseada em uma pesquisa bibliográfica de pesquisa exploratória que consistiu de três estudos de caso em empresas de diferenças localizadas em Sorocaba, São Paulo. Neste artigo estuda a aplicação de Lean Seis Sigma e seus resultados.

Lean six sigma application to transportation logistics

Directory of Open Access Journals (Sweden)

Simone Tavares Fernandes

2012-06-01

Full Text Available This work presents the application of Lean Six Sigma in a case study of a metallurgic industry. The Six Sigma and the Lean are two processes used by enterprises in Brazil and worldwide. Currently the integration of these processes is a challenge for these companies, which search a way more efficient to reduce their wastes and to adapt to the needs of their markets. The paper had as purpose to demonstrate the applicability of the Lean Six Sigma in a real logistical problem related to the transportation of goods among units of a metallurgic industry. The stages used for the solution of the problem follow the DMAIC cycle – Define, Measure, Analyze, Improve and Control. The paper presents in details the integrated approach of the improvement processes Lean and Six Sigma, their tools set, as well the excellent results obtained in the case study.

Decontamination of burns contaminated with radioactive materials

International Nuclear Information System (INIS)

Vykouril, L.

1986-01-01

The suitability of various solutions for the decontamination of burnt skin and their efficiency were tested by experiments on rats. Tested was the decontamination of undisturbed skin, second degree skin burns and third degree skin burns. Decontamination solutions used included: distilled water, jodonal (an aqueous solution of iodine, ethoxylated nonylphenols, the copolymer of ethylene oxide with propylene oxide, and phosphoric acid) and a decontamination mixture of Sapon, Komplexon (trade names of detergents) and sodium hexametaphosphate. Decontamination efficiency was 68.4% for second degree burns and 47.1% for third degree burns. Most effective was the decontamination solution with an efficiency of 72%; the efficiency of jodonal was 67% and of water - 54%. Jodonal is the most suitable: in addition, it acts as a disinfectant and antiseptic. (M.D.)

What Determines Lean Manufacturing Implementation? A CB-SEM Model

Directory of Open Access Journals (Sweden)

Tan Ching Ng

2018-02-01

Full Text Available This research aims to ascertain the determinants of effective Lean Manufacturing (LM. In this research, Covariance-based Structural Equation Modeling (CB-SEM analysis will be used in order to analyze the determinants. Through CB-SEM analysis, the significant key determinants can be determined and the direct relationships among determinants can be analyzed. Thus, the findings of this research can act as guidelines for achievement of LM effectiveness, not only providing necessary steps for successful implementation of lean, but also helping lean companies to achieve higher level of lean cost and time savings.

Buildings Lean Maintenance Implementation Model

Science.gov (United States)

Abreu, Antonio; Calado, João; Requeijo, José

2016-11-01

Nowadays, companies in global markets have to achieve high levels of performance and competitiveness to stay "alive".Within this assumption, the building maintenance cannot be done in a casual and improvised way due to the costs related. Starting with some discussion about lean management and building maintenance, this paper introduces a model to support the Lean Building Maintenance (LBM) approach. Finally based on a real case study from a Portuguese company, the benefits, challenges and difficulties are presented and discussed.

The challenges of lean manufacturing implementation in kitting assembly

Science.gov (United States)

Fansuri, A. F. H.; Rose, A. N. M.; Nik Mohamed, N. M. Z.; Ahmad, H.

2017-10-01

Literature studies shows that lean manufacturing goes way back with the original founder Eli Whitney in year 1799. The main purpose of lean manufacturing is to identify and eliminate waste in production. The application of lean manufacturing can be carried out in any industrial processes with regards to the understanding of lean principles, theories and practices. Kitting is one of the important aspects in a successful production. The continuous supply of materials from store to production has to be systematic and able to achieve lean standard for it to be successful. The objective of this paper is to review the implementation of lean manufacturing in kitting assembly. Previous papers show that, the implementation of lean manufacturing in kitting assembly may be beneficial to the organization such as reduce in space occupancy, part shortages, lead time and manpower. Based on previous research, some industries may tend to change between kitting and line stocking which are due to lack of understanding when implementing kitting and causes longer lead time and materials overflow in store. With a proper understanding on what to kit, where to kit, how to kit, why to kit and who kits the material with a standardised process flow may ensure the success of kitting.

Improvement of emergency department patient flow using lean thinking.

Science.gov (United States)

Sánchez, Miquel; Suárez, Montse; Asenjo, María; Bragulat, Ernest

2018-05-01

To apply lean thinking in triage acuity level-3 patients in order to improve emergency department (ED) throughtput and waiting time. A prospective interventional study. An ED of a tertiary care hospital. Triage acuity level-3 patients. To apply lean techniques such as value stream mapping, workplace organization, reduction of wastes and standardization by the frontline staff. Two periods were compared: (i) pre-lean: April-September, 2015; and (ii) post-lean: April-September, 2016. Variables included: median process time (time from beginning of nurse preparation to the end of nurse finalization after doctor disposition) of both discharged and transferred to observation patients; median length of stay; median waiting time; left without being seen, 72-h revisit and mortality rates, and daily number of visits. There was no additional staff or bed after lean implementation. Despite an increment in the daily number of visits (+8.3%, P lean implementation. No significant differences were registered in left without being seen rate (5.23% vs 4.95%), 72-h revisit rate (3.41% vs 3.93%), and mortality rate (0.23% vs 0.15%). Lean thinking is a methodology that can improve triage acuity level-3 patient flow in the ED, resulting in better throughput along with reduced waiting time.

Performance effect of multiple control forms in a Lean organization

DEFF Research Database (Denmark)

Kristensen, Thomas Borup; Israelsen, Poul

2012-01-01

Over the last decades Lean has developed into a prominent management philosophy reaching beyond shop floor tools. However, substantial support of performance effects from Lean is still scarce and at best with mixed results. Recently, research has turned its focus towards perceiving Lean...... as a control package. In this paper we present statistical support for enhanced performance coming from Lean. Furthermore, our results strongly support the perception of Lean as a set of multiple control forms (output, behavioral, and social controls) that complement each other. Therefore, performance...... is increased if the average level of control forms is increased, and performance is further increased if the control forms are balanced at the same level representing a complementary effect between them. Our data are archival data spanning multiple years in a strong Lean organization. The dependent performance...

Lean principles applied to software development – avoiding waste

Directory of Open Access Journals (Sweden)

Ionel NAFTANAILA

2009-12-01

Full Text Available Under the current economic conditions many organizations strive to continue the trend towards adopting better software development processes, in order to take advantage of the numerous benefits that these can offer. Those benefits include quicker return on investment, better software quality, and higher customer satisfaction. To date, however, there is little body of research that can guide organizations in adopting modern software development practices, especially when it comes to Lean thinking and principles. To address this situation, the current paper identifies and structures the main wastes (or muda in Lean terms in software development as described by Lean principles, in an attempt to bring into researchers’ and practitioners’ attention Lean Software Development, a modern development methodology based on well-established practices such as Lean Manufacturing or Toyota Production System.

How does lean work in emergency care? A case study of a lean-inspired intervention at the Astrid Lindgren Children's hospital, Stockholm, Sweden

Directory of Open Access Journals (Sweden)

Mazzocato Pamela

2012-02-01

Full Text Available Abstract Background There is growing interest in applying lean thinking in healthcare, yet, there is still limited knowledge of how and why lean interventions succeed (or fail. To address this gap, this in-depth case study examines a lean-inspired intervention in a Swedish pediatric Accident and Emergency department. Methods We used a mixed methods explanatory single case study design. Hospital performance data were analyzed using analysis of variance (ANOVA and statistical process control techniques to assess changes in performance one year before and two years after the intervention. We collected qualitative data through non-participant observations, semi-structured interviews, and internal documents to describe the process and content of the lean intervention. We then analyzed empirical findings using four theoretical lean principles (Spear and Bowen 1999 to understand how and why the intervention worked in its local context as well as to identify its strengths and weaknesses. Results Improvements in waiting and lead times (19-24% were achieved and sustained in the two years following lean-inspired changes to employee roles, staffing and scheduling, communication and coordination, expertise, workspace layout, and problem solving. These changes resulted in improvement because they: (a standardized work and reduced ambiguity, (b connected people who were dependent on one another, (c enhanced seamless, uninterrupted flow through the process, and (d empowered staff to investigate problems and to develop countermeasures using a "scientific method". Contextual factors that may explain why not even greater improvement was achieved included: a mismatch between job tasks, licensing constraints, and competence; a perception of being monitored, and discomfort with inter-professional collaboration. Conclusions Drawing on Spear and Bowen's theoretical propositions, this study explains how a package of lean-like changes translated into better care process

How does lean work in emergency care? A case study of a lean-inspired intervention at the Astrid Lindgren Children's hospital, Stockholm, Sweden

Science.gov (United States)

2012-01-01

Background There is growing interest in applying lean thinking in healthcare, yet, there is still limited knowledge of how and why lean interventions succeed (or fail). To address this gap, this in-depth case study examines a lean-inspired intervention in a Swedish pediatric Accident and Emergency department. Methods We used a mixed methods explanatory single case study design. Hospital performance data were analyzed using analysis of variance (ANOVA) and statistical process control techniques to assess changes in performance one year before and two years after the intervention. We collected qualitative data through non-participant observations, semi-structured interviews, and internal documents to describe the process and content of the lean intervention. We then analyzed empirical findings using four theoretical lean principles (Spear and Bowen 1999) to understand how and why the intervention worked in its local context as well as to identify its strengths and weaknesses. Results Improvements in waiting and lead times (19-24%) were achieved and sustained in the two years following lean-inspired changes to employee roles, staffing and scheduling, communication and coordination, expertise, workspace layout, and problem solving. These changes resulted in improvement because they: (a) standardized work and reduced ambiguity, (b) connected people who were dependent on one another, (c) enhanced seamless, uninterrupted flow through the process, and (d) empowered staff to investigate problems and to develop countermeasures using a "scientific method". Contextual factors that may explain why not even greater improvement was achieved included: a mismatch between job tasks, licensing constraints, and competence; a perception of being monitored, and discomfort with inter-professional collaboration. Conclusions Drawing on Spear and Bowen's theoretical propositions, this study explains how a package of lean-like changes translated into better care process management. It adds

Advancing lean manufacturing, the role of IT

NARCIS (Netherlands)

Riezebos, J.; Klingenberg, W.

This introduction to the special issue discusses the changing role of information technology (IT) in advancing lean production. Lean principles and techniques have been applied in a wide variety of organisations, from make-to-stock to engineer-to-order industries, and even in typical service

System-wide lean implementation in health care: A multiple case study.

Science.gov (United States)

Centauri, Federica; Mazzocato, Pamela; Villa, Stefano; Marsilio, Marta

2018-05-01

Background Lean practices have been widely used by health care organizations to meet efficiency, performance and quality improvement needs. The lean health care literature shows that the effective implementation of lean requires a holistic system-wide approach. However, there is still limited evidence on what drives effective system-wide lean implementation in health care. The existing literature suggests that a deeper understanding of how lean interventions interact with the organizational context is necessary to identify the critical variables to successfully sustain system-wide lean strategies. Purpose and methodology: A multiple case study of three Italian hospitals is conducted with the aim to explore the organizational conditions that are relevant for an effective system-wide lean implementation. A conceptual framework, built on socio-technical system schemas, is used to guide data collection and analysis. The analysis points out the importance to support lean implementation with an integrated and coordinated strategy involving the social, technical, and external components of the overall hospital system.

Lean thinking in emergency departments: concepts and tools for quality improvement.

Science.gov (United States)

Bruno, Frances

2017-10-12

The lean approach is a viable framework for reducing costs and enhancing the quality of patient care in emergency departments (EDs). Reports on lean-inspired quality improvement initiatives are rapidly growing but there is little emphasis on the philosophy behind the processes, which is the essential ingredient in sustaining transformation. This article describes lean philosophy, also referred to as lean, lean thinking and lean healthcare, and its main concepts, to enrich the knowledge and vocabulary of nurses involved or interested in quality improvement in EDs. The article includes examples of lean strategies to illustrate their practical application in EDs. ©2012 RCN Publishing Company Ltd. All rights reserved. Not to be copied, transmitted or recorded in any way, in whole or part, without prior permission of the publishers.

[Surgical treatment of burns : Special aspects of pediatric burns].

Science.gov (United States)

Bührer, G; Beier, J P; Horch, R E; Arkudas, A

2017-05-01

Treatment of pediatric burn patients is very important because of the sheer frequency of burn wounds and the possible long-term ramifications. Extensive burns need special care and are treated in specialized burn centers. The goal of this work is to present current standards in burn therapy and important innovations in the treatment of burns in children so that the common and small area burn wounds and scalds in pediatric patients in day-to-day dermatological practice can be adequately treated. Analysis of current literature, discussion of reviews, incorporation of current guidelines. Burns in pediatric patients are common. Improvement of survival can be achieved by treatment in burn centers. The assessment of burn depth and area is an important factor for proper treatment. We give an overview for outpatient treatment of partial thickness burns. New methods may result in better long-term outcome. Adequate treatment of burn injuries considering current literature and guidelines improves patient outcome. Rational implementation of new methods is recommended.

Improvement of laboratory turnaround time using lean methodology.

Science.gov (United States)

Gupta, Shradha; Kapil, Sahil; Sharma, Monica

2018-05-14

Purpose The purpose of this paper is to discuss the implementation of lean methodology to reduce the turnaround time (TAT) of a clinical laboratory in a super speciality hospital. Delays in report delivery lead to delayed diagnosis increased waiting time and decreased customer satisfaction. The reduction in TAT will lead to increased patient satisfaction, quality of care, employee satisfaction and ultimately the hospital's revenue. Design/methodology/approach The generic causes resulting in increasing TAT of clinical laboratories were identified using lean tools and techniques such as value stream mapping (VSM), Gemba, Pareto Analysis and Root Cause Analysis. VSM was used as a tool to analyze the current state of the process and further VSM was used to design the future state with suggestions for process improvements. Findings This study identified 12 major non-value added factors for the hematology laboratory and 5 major non-value added factors for the biochemistry lab which were acting as bottlenecks resulting in limiting throughput. A four-month research study by the authors together with hospital quality department and laboratory staff members led to reduction of the average TAT from 180 to 95minutes in the hematology lab and from 268 to 208 minutes in the biochemistry lab. Practical implications Very few improvement initiatives in Indian healthcare are based on industrial engineering tools and techniques, which might be due to a lack of interaction between healthcare and engineering. The study provides a positive outcome in terms of improving the efficiency of services in hospitals and identifies a scope for lean in the Indian healthcare sector. Social implications Applying lean in the Indian healthcare sector gives its own potential solution to the problem caused, due to a wide gap between lean accessibility and lean implementation. Lean helped in changing the mindset of an organization toward providing the highest quality of services with faster delivery at

Towards more efficient burn care: Identifying factors associated with good quality of life post-burn.

Science.gov (United States)

Finlay, V; Phillips, M; Allison, G T; Wood, F M; Ching, D; Wicaksono, D; Plowman, S; Hendrie, D; Edgar, D W

2015-11-01

As minor burn patients constitute the vast majority of a developed nation case-mix, streamlining care for this group can promote efficiency from a service-wide perspective. This study tested the hypothesis that a predictive nomogram model that estimates likelihood of good long-term quality of life (QoL) post-burn is a valid way to optimise patient selection and risk management when applying a streamlined model of care. A sample of 224 burn patients managed by the Burn Service of Western Australia who provided both short and long-term outcomes was used to estimate the probability of achieving a good QoL defined as 150 out of a possible 160 points on the Burn Specific Health Scale-Brief (BSHS-B) at least six months from injury. A multivariate logistic regression analysis produced a predictive model provisioned as a nomogram for clinical application. A second, independent cohort of consecutive patients (n=106) was used to validate the predictive merit of the nomogram. Male gender (p=0.02), conservative management (p=0.03), upper limb burn (p=0.04) and high BSHS-B score within one month of burn (pburns were excluded due to loss to follow up. For clinicians managing comparable burn populations, the BSWA burns nomogram is an effective tool to assist the selection of patients to a streamlined care pathway with the aim of improving efficiency of service delivery. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Disturbing Practices: Training Workers to Be Lean

Science.gov (United States)

Yasukawa, Keiko; Brown, Tony; Black, Stephen

2014-01-01

Purpose: The purpose of this paper is to explore the possibilities for expansive learning during organisational change. It considers the introduction of "lean production" as a disturbance to the existing work practices. Design/methodology/approach: The paper considers two case studies of "lean production" training with…

Lean Thinking and Transferring Lean Management - The Best Defence against an Economic Recession?

Directory of Open Access Journals (Sweden)

Daniel D. GEORGESCU

2011-06-01

Full Text Available Productivity growth is a fundamental means for society to improve its living standards. Productivity growth comes from technological change (new ways of producing goods and services and better organisation of production (better ways of using available resources given available technology. Both processes operate simultaneously and, in practice, it is difficult to distinguish between the effects of each process. The processes are dynamic and affect individual activities differently over time. These years, manufacturing functions have been transferred rapidly and globally from mature countries to emerging countries. This paper is about the lean philosophy and the critical elements for successful transfer of lean management among sites and countries.

Lean implementation strategies: how are the Toyota way principles addressed?

Directory of Open Access Journals (Sweden)

Coetzee, Rojanette

2016-11-01

Full Text Available Lean manufacturing is widely considered to be a proven organisational improvement philosophy, yet the success rate of lean implementation in industry remains relatively low. Neglect of the human aspect of lean manufacturing is often cited as the leading reason for this, despite the emphasis so clearly placed upon this aspect by the creators of the lean philosophy. This article reviews the extent to which the human dimensions of the lean philosophy, as described in the Toyota Way management principles, have been incorporated in lean implementation strategies. It is found that few of the principles feature prominently in these strategies. Notably absent are those linked to the ‘respect for people’ pillar , which forms half of the T oyota Way’s foundation. This conclusion indicates that the adoption of the lean philosophy runs contrary to the oft-repeated message from its creators that no tenet of the philosophy should be favoured at the expense of another. This may provide valuable insight into the reasons for the high implementation failure rate.

Lean healthcare in developing countries: evidence from Brazilian hospitals.

Science.gov (United States)

Costa, Luana Bonome Message; Filho, Moacir Godinho; Rentes, Antonio Freitas; Bertani, Thiago Moreno; Mardegan, Ronaldo

2017-01-01

The present study evaluates how five sectors of two Brazilian hospitals have implemented lean healthcare concepts in their operations. The main characteristics of the implementation process are analyzed in the present study: the motivational factor for implementation, implementation time, form (consultancy or internal), team (hospital and consultants), lean implementation continuity/sustainability, lean healthcare tools and methods implemented, problems/improvement opportunities, lean healthcare barriers faced during the implementation process, and critical factors that affected the implementation and the results obtained in each case. The case studies indicate that reducing patient lead times and costs and making financial improvements were the primary factors that motivated lean healthcare implementation in the hospitals studied. Several tools and methods were used in the cases studied, especially value stream mapping and DMAIC. The barriers found in both hospitals are primarily associated with the human factor. Additionally, the results obtained after implementation were analyzed and improvements in financial aspects, productivity and capacity, and lead time reduction of the analyzed sectors were observed. Further, this study also exhibited four propositions elaborated from the results obtained from the cases that highlighted barriers and challenges to lean healthcare implementation in developing countries. Two of these barriers are hospital organizational structure (and, consequently, how the senior management works with medical staff), and outsourcing hospital activities. This study also concluded that the initialization and maintenance of lean healthcare implementation rely heavily on external support because lean healthcare subject knowledge is not yet available in the healthcare organization, which represents a challenge. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

Lean spare parts delivery chain

OpenAIRE

Sjöstrand, Niklas; Larsson, Mona-Liza

2015-01-01

AbstractWhen a product has been sold to a customer a new market arises for the company to earn profit from and to differentiate itself within. According to Bartwal, et al. (2010) the after sales market generally does not provide great revenues but good profits of the total revenue. In order to gain competiveness and live up to customer’s expectations a company needs to be efficient (Atkinson, 2004). He continuous that this can be accomplished if companies implement Lean. Lean is different too...

Review of high burn-up RIA and LOCA database and criteria

International Nuclear Information System (INIS)

Vitanza, C.; Hrehor, M.

2006-01-01

This document is intended to provide regulators, their technical support organizations and industry with a concise review of existing fuel experimental data at RIA and LOCA conditions and considerations on how these data affect fuel safety criteria at increasing burn-up. It mostly addresses experimental results relevant to BWR and PWR fuel and it encompasses several contributions from the various experts that participated in the CSNI SEGFSM activities. It also covers the information presented at the joint CSNI/CNRA Topical Discussion on high burn-up fuel issues that took place on this subject in December 2004. The report is organized in the following way: the CABRI RIA database (14 tests), the NSRR database (26 tests) and other databases, RIA failure thresholds, comparison of failure thresholds for the HZP case, LOCA database ductility tests and quench tests, LOCA safety limit, provisional burn-up dependent criterion for Zr-4. The conclusions are as follows. On RIA, there is a well-established testing method and a significant and relatively consistent database from NSRR and Cabri tests, especially on high burn-up Zr-2 and Zr-4 cladding. It is encouraging that several correlations have been proposed for the RIA fuel failure threshold. Their predictions are compared and discussed in this paper for a representative PWR case. On LOCA, there are two different test methods, one based on ductility determinations and the other based on 'integral' quench tests. The LOCA database at high burn-up is limited to both testing methods. Ductility tests carried out with pre-hydrided non-irradiated cladding show a pronounced hydrogen effect. Data for actual high burn-up specimens are being gathered in various laboratories and will form the basis for a burn-up dependent LOCA limit. A provisional burn-up dependent criterion is discussed in the paper

Investigating emergency room service quality using lean manufacturing.

Science.gov (United States)

Abdelhadi, Abdelhakim

2015-01-01

The purpose of this paper is to investigate a lean manufacturing metric called Takt time as a benchmark evaluation measure to evaluate a public hospital's service quality. Lean manufacturing is an established managerial philosophy with a proven track record in industry. A lean metric called Takt time is applied as a measure to compare the relative efficiency between two emergency departments (EDs) belonging to the same public hospital. Outcomes guide managers to improve patient services and increase hospital performances. The patient treatment lead time within the hospital's two EDs (one department serves male and the other female patients) are the study's focus. A lean metric called Takt time is used to find the service's relative efficiency. Findings show that the lean manufacturing metric called Takt time can be used as an effective way to measure service efficiency by analyzing relative efficiency and identifies bottlenecks in different departments providing the same services. The paper presents a new procedure to compare relative efficiency between two EDs. It can be applied to any healthcare facility.

Lean management-the journey from toyota to healthcare.

Science.gov (United States)

Teich, Sorin T; Faddoul, Fady F

2013-04-01

The evolution of production systems is tightly linked to the story of Toyota Motor Company (TMC) that has its roots around 1918. The term "lean" was coined in 1990 following the exploration of the Toyota model that led to the "transference" thesis sustaining the concept that manufacturing problems and technologies are universal problems faced by management and that these concepts can be emulated in non-Japanese enterprises. Lean is a multi-faceted concept and requires organizations to exert effort along several dimensions simultaneously; some consider a successful implementation either achieving major strategic components of lean, implementing practices to support operational aspects, or providing evidence that the improvements are sustainable in the long term. The article explores challenges and opportunities faced by organizations that intend incorporating lean management principles and presents the specific context of the healthcare industry. Finally, the concepts of "essential few" and customer value are illustrated through a simple example of process change following lean principles, which was implemented in a dental school in the United States.

Glucose metabolism in obese and lean adolescents with polycystic ovary syndrome.

Science.gov (United States)

Poomthavorn, Preamrudee; Chaya, Weerapong; Mahachoklertwattana, Pat; Sukprasert, Matchuporn; Weerakiet, Sawaek

2013-01-01

Data on glucose metabolism in Asian adolescents with polycystic ovary syndrome (PCOS) are limited. Glucose metabolism assessment using an oral glucose tolerance test (OGTT) in obese and lean Thai adolescents with PCOS, and a comparison between the two groups were done. Thirty-one patients (19 obese, 12 lean) were enrolled. Their median (range) age was 14.9 (11.0-21.0) years. Eighteen patients had abnormal glucose metabolism (13 hyperinsulinemia, 4 impaired glucose tolerance, and 1 diabetes). Compared between obese [median (range) BMI Z-score, 1.6 (1.2-2.6)] and lean [median (range) BMI Z-score, 0.1 (-1.4 to 0.6)] patients, the frequencies of each abnormal OGTT category, areas under the curves of glucose and insulin levels, and insulinogenic index were not different; however, insulin resistance was greater in the obese group. In conclusion, a high proportion of our adolescents with PCOS had abnormal glucose metabolism. Therefore, OGTT should be performed in adolescents with PCOS for the early detection of abnormal glucose metabolism.

Lean manufacturing: A better way for enhancement in productivity

Science.gov (United States)

Kumar Ahir, Pankaj; Kumar Yadav, Lalit; Singh Chandrawat, Saurabh

2012-03-01

Productivity is the impact of peoples working together. Machines are merely an extended way of collective imagination and energy. Lean Manufacturing is the most used method for continues improvement of business. Organization management philosophy focusing on the reduction of wastage to improve overall customer value. "Lean" operating principles began in manufacturing environments and are known by a variety of synonyms; Lean Manufacturing, Lean Production, Toyota Production System, etc. It is commonly believed that Lean started in Japan "The notable activities in keeping the price of Ford products low is the steady restriction of the production cycle. The longer an article is in the process of manufacture and the more it is moved about, the greater is its ultimate cost." "A systematic approach to identifying and eliminating waste through continuous improvement, flowing the product at the pull of the customer in pursuit of perfection."

Simulated LOCA Test and Characterization Study Related to High Burn-Up Issue

International Nuclear Information System (INIS)

Park, D. J.; Jung, Y. I.; Choi, B. K.; Park, S. Y.; Kim, H. G.; Park, J. Y.

2012-01-01

For the safety evaluation of fuel cladding during the injection of emergency core coolant, simulated Loss-of-coolant accident (LOCA) test was performed by using Zircaloy-4 fuel cladding samples. Zircaloy-4 tube samples with and without prehydring were oxidized in a steam environment with the test temperature of 1200 .deg. C. Prehydrided cladding was prepared from as-fabricated Zircaloy-4 to study the effects of hydrogen on mechanical properties of cladding during high temperature oxidation and quench conditions. In order to measure the ductility of the tube samples embrittled by quenching water, ring compression test was carried out by using 8 mm ring sample sectioned from oxidized tube sample and microstructural analysis was also performed after simulated LOCA test. The results showed that hydrogen increases oxygen solubility and pickup rate in the beta layer. This reduces ductility of prehydrided fuel cladding compared with as-fabricated cladding. Trend in ductility decrease for prehydrided sample under simulated LOCA condition was very similar with data obtained from tests conducted using irradiated high burn-up fuel claddings

SRC burn test in 700-hp oil-designed boiler. Annex Volume C. Boiler emission report. Final technical report

Energy Technology Data Exchange (ETDEWEB)

1983-09-01

The Solvent-Refined Coal (SRC) test burn program was conducted at the Pittsburgh Energy Technology Center (PETC) located in Bruceton, Pa. One of the objectives of the study was to determine the feasibility of burning SRC fuels in boilers set up for fuel oil firing and to characterize emissions. Testing was conducted on the 700-hp oil-fired boiler used for research projects. No. 6 fuel oil was used for baseline data comparison, and the following SRC fuels were tested: SRC Fuel (pulverized SRC), SRC Residual Oil, and SRC-Water Slurry. Uncontrolled particulate emission rates averaged 0.9243 lb/10/sup 6/ Btu for SRC Fuel, 0.1970 lb/10/sup 6/ Btu for SRC Residual Oil, and 0.9085 lb/10/sup 6/ Btu for SRC-Water Slurry. On a lb/10/sup 6/ Btu basis, emissions from SRC Residual Oil averaged 79 and 78%, respectively, lower than the SRC Fuel and SRC-Water Slurry. The lower SRC Residual Oil emissions were due, in part, to the lower ash content of the oil and more efficient combustion. The SRC Fuel had the highest emission rate, but only 2% higher than the SRC-Water Slurry. Each fuel type was tested under variable boiler operating parameters to determine its effect on boiler emissions. The program successfully demonstrated that the SRC fuels could be burned in fuel oil boilers modified to handle SRC fuels. This report details the particulate emission program and results from testing conducted at the boiler outlet located before the mobile precipitator take-off duct. The sampling method was EPA Method 17, which uses an in-stack filter.

Lean Start-up in Established Companies

DEFF Research Database (Denmark)

Goduscheit, René Chester

2018-01-01

Lean start-up is an emergent perspective on how entrepreneurs can bring new products and services to the market. This approach challenges the dominant role of lengthy business plans, linear product development processes, and seeking complete overview of the potential of the new products....../services before market launch. Instead it suggests that start-ups could benefit from a ‘minimum-viable product’ approach where products and services are launched when they contain critical features. The emphasis in the lean start-up approach is on business models rather than the elaborate business plan...... at the companies (strategy meetings, development workshops etc.). The aim is to shed light on the implications for companies that seek to employ lean start-up. These implications will be aimed at aspects like innovation management, organizational structure, customer relations etc....

In-situ burning: NIST studies

International Nuclear Information System (INIS)

Evans, D.D.

1992-01-01

In-situ burning of spilled oil has distinct advantages over other countermeasures. It offers the potential to convert rapidly large quantities of oil into its primary combustion products, carbon dioxide and water, with a small percentage of other unburned and residue byproducts. Because the oil is converted to gaseous products of combustion by burning, the need for physical collection, storage, and transport of recovered fluids is reduced to the few percent of the original spill volume that remains as residue after burning. Burning oil spills produces a visible smoke plume containing smoke particulate and other products of combustion which may persist for many kilometers from the burn. This fact gives rise to public health concerns, related to the chemical content of the smoke plume and the downwind deposition of particulate, which need to be answered. In 1985, a joint Minerals Management Service (MMS) and Environment Canada (EC) in-situ burning research program was begun at the National Institute of Standards and Technology (NIST). This research program was designed to study the burning of large crude oil spills on water and how this burning would affect air quality by quantifying the products of combustion and developing methods to predict the downwind smoke particulate deposition. To understand the important features of in-situ burning, it is necessary to perform both laboratory and mesoscale experiments. Finally, actual burns of spilled oil at sea will be necessary to evaluate the method at the anticipated scale of actual response operations. In this research program there is a continuing interaction between findings from measurements on small fire experiments performed in the controlled laboratory environments of NIST and the Fire Research Institute (FRI) in Japan, and large fire experiments at facilities like the USCG Fire Safety and Test Detachment in Mobile, Alabama where outdoor liquid fuel burns in large pans are possible

Debates Regarding Lean Patients with Polycystic Ovary Syndrome: A Narrative Review.

Science.gov (United States)

Goyal, Manu; Dawood, Ayman S

2017-01-01

Polycystic ovary syndrome (PCOS) is a complex syndrome showing the clinical features of an endocrine/metabolic disorder, including hyperinsulinemia and hyperandrogenism. Two phenotypes are present, either lean or obese, with different biochemical, hormonal, and metabolic profiles. Evidence suggests many treatment modalities that can be applied. However, many of these modalities were found to be not suitable for the lean phenotype of PCOS. Much contradictory research was found regarding lean patients with PCOS. The aim of this narrative review is to shed light on the debate prevailing regarding characteristics, as well as metabolic, hematological, and potential management modalities. Literature review was performed from January 1, 2000 to March 31, 2017 with specific word search such as lean PCOS, hormonal abnormalities in lean PCOS, and the management of lean PCOS. All retrieved articles were carefully assessed, and data were obtained. We could conclude that the debate is still prevailing regarding this specific lean population with PCOS, especially with regard to their characteristics and management modalities. Further studies are still required to resolve this debate on the presence of PCOS in lean women.

Debates regarding lean patients with polycystic ovary syndrome: A narrative review

Directory of Open Access Journals (Sweden)

Manu Goyal

2017-01-01

Full Text Available Polycystic ovary syndrome (PCOS is a complex syndrome showing the clinical features of an endocrine/metabolic disorder, including hyperinsulinemia and hyperandrogenism. Two phenotypes are present, either lean or obese, with different biochemical, hormonal, and metabolic profiles. Evidence suggests many treatment modalities that can be applied. However, many of these modalities were found to be not suitable for the lean phenotype of PCOS. Much contradictory research was found regarding lean patients with PCOS. The aim of this narrative review is to shed light on the debate prevailing regarding characteristics, as well as metabolic, hematological, and potential management modalities. Literature review was performed from January 1, 2000 to March 31, 2017 with specific word search such as lean PCOS, hormonal abnormalities in lean PCOS, and the management of lean PCOS. All retrieved articles were carefully assessed, and data were obtained. We could conclude that the debate is still prevailing regarding this specific lean population with PCOS, especially with regard to their characteristics and management modalities. Further studies are still required to resolve this debate on the presence of PCOS in lean women.

Simultaneous measurement of the surface temperature and the release of atomic sodium from a burning black liquor droplet

Energy Technology Data Exchange (ETDEWEB)

Saw, Woei L.; Nathan, Graham J. [Centre for Energy Technology, The University of Adelaide, SA 5006 (Australia); School of Mechanical Engineering, The University of Adelaide (Australia); Ashman, Peter J.; Alwahabi, Zeyad T. [Centre for Energy Technology, The University of Adelaide, SA 5006 (Australia); School of Chemical Engineering, The University of Adelaide (Australia); Hupa, Mikko [Process Chemistry Centre, Aabo Akademi, Biskopsgatan 8 FI-20500 Aabo (Finland)

2010-04-15

Simultaneous measurement of the concentration of released atomic sodium, swelling, surface and internal temperature of a burning black liquor droplet under a fuel lean and rich condition has been demonstrated. Two-dimensional two-colour optical pyrometry was employed to determine the distribution of surface temperature and swelling of a burning black liquor droplet while planar laser-induced fluorescence (PLIF) was used to assess the temporal release of atomic sodium. The key findings of these studies are: (i) the concentration of atomic sodium released during the drying and devolatilisation stages was found to be correlated with the external surface area; and (ii) the insignificant presence of atomic sodium during the char consumption stage shows that sodium release is suppressed by the lower temperature and by the high CO{sub 2} content in and around the particle. (author)

Assessing the impacts of implementing lean construction Evaluando los impactos de la implementación de lean construction

Directory of Open Access Journals (Sweden)

Luis F Alarcón

2008-04-01

Full Text Available Over the last 10 years an increasing number of companies have implemented lean construction practices in an attempt to improve performance in construction projects. Most companies, and also some researchers, have reported satisfactory results from their implementation. However, there is still a need to provide more extensive analysis of the empirical evidence available to assess the impact of the implementation of lean construction. The authors have researched the implementation of the Last Planner System and other Lean Construction techniques in over one hundred construction projects over the last five years. They have also developed strategies and support tools for implementation. This paper analyzes some of the main impacts observed in the studied projects, and some of the lessons learned from implementations. The paper discusses difficulties and barriers for implementation, productivity improvements, variability reduction and effectiveness of implementation strategies. The paper also provides recommendations for future implementation and researchEn los últimos 10 años un creciente número de empresas constructoras ha implementado prácticas de Lean Construction para mejorar el desempeño de sus proyectos. La mayor parte de estas empresas, y también algunos investigadores, han informado sobre buenos resultados obtenidos en los proyectos. Sin embargo, todavía es necesario un análisis más completo de la evidencia empírica disponible para evaluar así el impacto de Lean Construction en los proyectos y empresas. Los autores han investigado la implementación del Sistema Ultimo Planificador y otras técnicas de Lean Construction en mas de un centenar de proyectos en los últimos 5 años y han desarrollado estrategias y herramientas de apoyo para su implementación. Este artículo analiza algunos de los principales impactos observados en los proyectos estudiados y las lecciones aprendidas en este proceso. Se discuten dificultades y barreras

Quality and Competitiveness: A Lean Six Sigma Approach

Directory of Open Access Journals (Sweden)

Irina-Virginia Drăgulănescu

2015-11-01

Full Text Available Originally developed to improve the quality and production efficiency, Lean Six Sigma is now widely adopted in other non-manufacturing sectors such as financial, trade, services, etc. The methodology known as Lean Six Sigma combines the Six Sigma techniques, ‒ which allow companies to reduce manufacturing defects ‒ and the Lean Manufacturing principles, ‒ which help companies benefit from faster processing for lower costs and with superior quality. As a result of the research, the authors observed that, despite growing popularity and impressive outcomes obtained by some companies, the Lean Six Sigma model does not always offer the expected results. However, the research has shown that the analysed company, operating in the field of courier services has managed to boost productivity and competitiveness by implementing measures that generated added value.

'Lean' approach gives greater efficiency.

Science.gov (United States)

Call, Roger

2014-02-01

Adapting the 'Lean' methodologies used for many years by many manufacturers on the production line - such as in the automotive industry - and deploying them in healthcare 'spaces' can, Roger Call, an architect at Herman Miller Healthcare in the US, argues, 'easily remedy many of the inefficiencies' found within a healthcare facility. In an article that first appeared in the September 2013 issue of The Australian Hospital Engineer, he explains how 'Lean' approaches such as the 'Toyota production system', and 'Six Sigma', can be harnessed to good effect in the healthcare sphere.

Does lean muddy the quality improvement waters? A qualitative study of how a hospital management team understands lean in the context of quality improvement.

Science.gov (United States)

Savage, Carl; Parke, Louise; von Knorring, Mia; Mazzocato, Pamela

2016-10-19

Health care has experimented with many different quality improvement (QI) approaches with greater variation in name than content. This has been dubbed pseudoinnovation. However, it could also be that the subtleties and differences are not clearly understood. To explore this further, the purpose of this study was to explore how hospital managers perceive lean in the context of QI. We used a qualitative study design with semi-structured interviews to explore twelve top managers' perceptions of the relationship between lean and quality improvement (QI) at a university-affiliated hospital. Managers described that QI and lean shared the same overall purpose: focus on patient needs and improve efficiency and effectiveness. Employee involvement was emphasized in both strategies, as well as the support offered by managers of staff initiatives. QI was perceived as a strategy that could support structural changes at the organizational level whereas lean was seen as applicable at the operational level. Moreover, lean carried a negative connotation, lacked the credibility of QI, and was perceived as a management fad. Aspects of QI and lean were misunderstood. In a context where lean remains an abstract term, and staff associate lean with automotive applications and cost reduction, it may be fruitful for managers to invest time and resources to develop a strategy for continual improvement and utilize vocabulary that resonates with health care staff. This could reduce the risk that improvement efforts are rejected out of hand.

The positive impact of simultaneous implementation of the BD FocalPoint GS Imaging System and lean principles on the operation of gynecologic cytology.

Science.gov (United States)

Wong, Rebecca; Levi, Angelique W; Harigopal, Malini; Schofield, Kevin; Chhieng, David C

2012-02-01

Our cytology laboratory, like many others, is under pressure to improve quality and provide test results faster while decreasing costs. We sought to address these issues by introducing new technology and lean principles. To determine the combined impact of the FocalPoint Guided Screener (GS) Imaging System (BD Diagnostics-TriPath, Burlington, North Carolina) and lean manufacturing principles on the turnaround time (TAT) and productivity of the gynecologic cytology operation. We established a baseline measure of the TAT for Papanicolaou tests. We then compared that to the performance after implementing the FocalPoint GS Imaging System and lean principles. The latter included value-stream mapping, workflow modification, and a first in-first out policy. The mean (SD) TAT for Papanicolaou tests before and after the implementation of FocalPoint GS Imaging System and lean principles was 4.38 (1.28) days and 3.20 (1.32) days, respectively. This represented a 27% improvement in the average TAT, which was statistically significant (P implementation of FocalPoint GS Imaging System in conjunction with lean principles resulted in a significant decrease in the average TAT for Papanicolaou tests and a substantial increase in the productivity of cytotechnologists while maintaining the diagnostic quality of gynecologic cytology.

Relationship Between Lean Production and Operational Performance in the Manufacturing Industry

Science.gov (United States)

Rasi, Raja Zuraidah R. M.; Syamsyul Rakiman, Umol; Ahmad, Md Fauzi Bin

2015-05-01

Nowadays, more and more manufacturing firms have started to implement lean production system in their operations. Lean production viewed as one of the mechanism to maintain the organisation's position and to compete globally. However, many fail to apply the lean concepts successfully in their operations. Based on previous studies, implementation of lean production in the manufacturing industry is more focused on the relationship between Lean and Operational Performance of one dimension only. Therefore, this study attempted to examine the relationship between Lean Production (LP) and Operational Performance in 4 dimensions which are quality, delivery, cost and flexibility. This study employed quantitative study using questionnaires. Data was collected from 50 manufacturing industries. The data was analysed using Statistical Package for Social Science (SPSS) 22.0. This study is hoped to shed new understanding on the concept of Lean Production (LP) in regards of Operational Performance covering the 4 dimensions.

Muscular Activities Measurements of Forward Lean and Upright Sitting Motorcycling Postures via Surface Electromyography (sEMG

Directory of Open Access Journals (Sweden)

Ma’arof Muhammad Izzat Nor

2017-01-01

Full Text Available Motorcycling postures are generically speculated to be physical and physiologically demanding – which in-turn may lead to motorcycling fatigue, and then becoming a possible factor to road accident. The objective of this study was to measure the muscular activities of various motorcycling postures. High muscular activity reading will signifies that motorcycling is indeed physically and physiologically demanding to the motorcyclist. For this particular study, the following postures were tested: i forward lean, ii upright sitting, and iii neutral sitting (as control. Surface electromyography (sEMG measurement was conducted on the following muscles: i extensor carpi radialis, ii upper trapezius iii latissimus dorsi, and iv erector spinae. The results showed that for all test subjects, the muscular activities readings for the forward lean posture was actually close to neutral sitting’s. Whilst, the upright sitting had showed much higher muscular activities measurement instead. Conclusively, this study had proven that any types of discomforts associated with the forward lean posture is not originated from muscular activities. Whereas, confirming that any discomforts in regards to the upright sitting is indeed related to muscular activities. Further studies are warranted to discover the actual risk factors that causes physical and physiological discomforts for the forward lean motorcycling posture.

Economic feasibility of hydrogen enrichment for reducing NOx emissions from landfill gas power generation alternatives: A comparison of the levelized cost of electricity with present strategies

International Nuclear Information System (INIS)

Kornbluth, Kurt; Greenwood, Jason; Jordan, Eddie; McCaffrey, Zach; Erickson, Paul A.

2012-01-01

Based on recent research showing that hydrogen enrichment can lower NO x emissions from landfill gas combustion below future NO x emission control standards imposed by both federal and California state regulations, an investigation was performed to compare the levelized cost of electricity of this technology with other options. In this cost study, a lean-burn reciprocating engine with no after-treatment was the baseline case to compare six other landfill gas-to-energy projects. These cases include a lean burn engine with selective catalytic reduction after treatment, a lean-burn microturbine, and four variations on an ultra-lean-burn engine utilizing hydrogen enrichment with each case using a different method of hydrogen production. Only hydrogen enrichment with an in-stream autothermal fuel reformer was shown to be potentially cost-competitive with current strategies for reaching the NO x reduction target in IC engines. - Highlights: ► Levelized cost of electricity for hydrogen enriched combustion was compared. ► Various ultra-lean-burn engines and microturbines with hydrogen were analyzed. ► Combustion with an autothermal fuel reformer was potentially cost-competitive.

Lean Production and information technology : Connection or contradiction?

NARCIS (Netherlands)

Riezebos, Jan; Klingenberg, Warse; Hicks, Christian

The principles of Lean Production have enabled organisations in the manufacturing and service sectors to significantly improve their competitiveness. The application of Lean principles, derived from the Toyota Production System has enabled many organisations to Simultaneously improve productivity,

Application of a mathematical model for ergonomics in lean manufacturing.

Science.gov (United States)

Botti, Lucia; Mora, Cristina; Regattieri, Alberto

2017-10-01

The data presented in this article are related to the research article "Integrating ergonomics and lean manufacturing principles in a hybrid assembly line" (Botti et al., 2017) [1]. The results refer to the application of the mathematical model for the design of lean processes in hybrid assembly lines, meeting both the lean principles and the ergonomic requirements for safe assembly work. Data show that the success of a lean strategy is possible when ergonomics of workers is a parameter of the assembly process design.

LEAN ACCOUNTING: SUATU ALTERNATIF TEKNIK AKUNTANSI MANAJEMEN DALAM INDUSTRI MANUFAKTUR

Directory of Open Access Journals (Sweden)

Eka Ardhani Sisdyani

2010-07-01

Full Text Available Manufacturing techniques have been developed to embrace theaims of continuous improvement. Continuous improvement would leadcompanies to win business competition. One technique that gains moreand more followers is lean manufacturing. Lean manufacturing hastwo main purposes, which are eliminating wastes and creating valuesto customers. It focuses on customer values, value stream, productionflows, demand-pull, and perfection. Lean accounting is needed tosupport and encourage the development of lean manufacturing, forinstances in product costing system, external reporting, and otherdecision making processes that need accounting data.

Lean Maintenance Applied to Improve Maintenance Efficiency in Thermoelectric Power Plants

Directory of Open Access Journals (Sweden)

Orlando Duran

2017-10-01

Full Text Available Thermoelectric power plants consist of a set of critical equipment that require high levels of availability and reliability. Due to this, maintenance of these physical assets is gaining momentum in industry. Maintenance is considered as an activity that contributes to improving the availability, efficiency and productivity of each piece of equipment. Several techniques have been used to achieve greater efficiencies in maintenance, among which we can find the lean maintenance philosophy. Despite the wide diffusion of lean maintenance, there is no structured method that supports the prescription of lean tools applied to the maintenance function. This paper presents the experience gathered in two lean maintenance projects in thermoelectric power plants. The application of lean techniques was based on using a previously developed multicriterial decision making process that uses the Fuzzy Analytic Hierarchy Process (AHP methodology to carry out a diagnosis and prescription tasks. That methodology allowed the prescription of the appropriated lean techniques to resolve the main deficiencies in maintenance function. The results of applying such lean tools show that important results can be obtained, making the maintenance function in thermoelectric power plants more efficient and lean.

Succesful Lean Manufacturing Implementation: Internal Key Influencing Factors

Science.gov (United States)

Virginia, Iuga; Claudiu, Kifor

2015-09-01

Manufacturing sectors and companies all over the world are successfully implementing lean principles within their processes. Nowadays, lean has become an indispensable part of global players. Companies worldwide need to be aware of multiple factors which weigh heavily on the success or failure of lean implementation. This paper focuses on giving a brief and structured overview over the fundamental organizational factors which play a substantial role for the lean manufacturing (LM) implementation process. The study below focuses on internal factors which are indispensable for a successful LM implementation within organizations. It is imperative that these internal factors are known, recognized and taken into consideration during the whole LM implementation process. Ignoring their influence on the process's implementation may lead to endangering the expected results or to making the process more difficult which could result in much higher human resource consumption.

Parameters Affecting the Erosive Burning of Solid Rocket Motor

Directory of Open Access Journals (Sweden)

Abdelaziz Almostafa

2018-01-01

Full Text Available Increasing the velocity of gases inside solid rocket motors with low port-to-throat area ratios, leading to increased occurrence and severity of burning rate augmentation due to flow of propellant products across burning propellant surfaces (erosive burning, erosive burning of high energy composite propellant was investigated to supply rocket motor design criteria and to supplement knowledge of combustion phenomena, pressure, burning rate and high velocity of gases all of these are parameters affect on erosive burning. Investigate the phenomena of the erosive burning by using the 2’inch rocket motor and modified one. Different tests applied to fulfil all the parameters that calculated out from the experiments and by studying the pressure time curve and erosive burning phenomena.

The current state of Lean implementation in health care: literature review.

Science.gov (United States)

Poksinska, Bozena

2010-01-01

The purpose of this article is to discuss the current state of implementation of Lean production in health care. The study focuses on the definition of Lean in health care and implementation process, barriers, challenges, enablers, and outcomes of implementing Lean production methods in health care. A comprehensive search of the literature concerning the implementation of Lean production in health care was used to generate a synthesis of the literature around the chosen research questions. Lean production in health care is mostly used as a process improvement approach and focuses on 3 main areas: (1) defining value from the patient point of view, (2) mapping value streams, and (3) eliminating waste in an attempt to create continuous flow. Value stream mapping is the most frequently applied Lean tool in health care. The usual implementation steps include conducting Lean training, initiating pilot projects, and implementing improvements using interdisciplinary teams. One of the barriers is lack of educators and consultants who have their roots in the health care sector and can provide support by sharing experience and giving examples from real-life applications of Lean in health care. The enablers of Lean in health care seem not to be different from the enablers of any other change initiative. The outcomes can be divided into 2 broad areas: the performance of the health care system and the development of employees and work environment.

Leaning on lean: the reception of a management fashion in Germany

NARCIS (Netherlands)

Benders, J.G.J.M.; Bijsterveld, M.J.L. van

2000-01-01

The ‘fashionable’ concept of lean production has been discussed more intensively in Germany than elsewhere in Europe but has resulted not only in rationalisation measures such as downsizing and delayering but also in implementing ‘Gruppenarbeit’. Through interpretation processes at different levels,

Burning characteristics of microcellular combustible objects

Directory of Open Access Journals (Sweden)

Wei-tao Yang

2014-06-01

Full Text Available Microcellular combustible objects for application of combustible case, caseless ammunition or combustible detonator-holding tubes are fabricated through one-step foaming process, in which supercritical CO2 is used as foaming agent. The formulations consist of inert polymer binder and ultra fine RDX. For the inner porous structures of microcellular combustible objects, the cell sizes present a unimodal or bimodal distribution by adjusting the foaming conditions. Closed bomb test is to investigate the influence of both porous structure style and RDX content on burning behavior. The sample with bimodal distribution of cell sizes burns faster than that with unimodal distribution, and the concentration of RDX can influence the burning characteristics in a positive manner. In addition, the translation of laminar burning to convective burning is determined by burning rate versus pressure curves of samples at two different loading densities, and the resulting transition pressure is 30 MPa. Moreover, the samples with bigger sample size present higher burning rate, resulting in providing deeper convective depth. Dynamic vivacity of samples is also studied. The results show that the vivacity increases with RDX content and varies with inner structure.

The prevalence of chest compression leaning during in-hospital cardiopulmonary resuscitation

Science.gov (United States)

Fried, David A.; Leary, Marion; Smith, Douglas A.; Sutton, Robert M.; Niles, Dana; Herzberg, Daniel L.; Becker, Lance B.; Abella, Benjamin S.

2011-01-01

Objective Successful resuscitation from cardiac arrest requires the delivery of high-quality chest compressions, encompassing parameters such as adequate rate, depth, and full recoil between compressions. The lack of compression recoil (“leaning” or “incomplete recoil”) has been shown to adversely affect hemodynamics in experimental arrest models, but the prevalence of leaning during actual resuscitation is poorly understood. We hypothesized that leaning varies across resuscitation events, possibly due to rescuer and/or patient characteristics and may worsen over time from rescuer fatigue during continuous chest compressions. Methods This was an observational clinical cohort study at one academic medical center. Data were collected from adult in-hospital and Emergency Department arrest events using monitor/defibrillators that record chest compression characteristics and provide real-time feedback. Results We analyzed 112,569 chest compressions from 108 arrest episodes from 5/2007 to 2/2009. Leaning was present in 98/108 (91%) cases; 12% of all compressions exhibited leaning. Leaning varied widely across cases: 41/108 (38%) of arrest episodes exhibited 20% compression leaning. When evaluating blocks of continuous compressions (>120 sec), only 4/33 (12%) had an increase in leaning over time and 29/33 (88%) showed a decrease (presuscitation care and exhibited a wide distribution, with most leaning within a subset of resuscitations. Leaning decreased over time during continuous chest compression blocks, suggesting that either leaning may not be a function of rescuer fatiguing, or that it may have been mitigated by automated feedback provided during resuscitation episodes. PMID:21482010

Severe burning treatment tested on lowland pine sites

Science.gov (United States)

S. Little; E. B. Moore

1953-01-01

Since the prescribed use of fire is a fairly new silvicultural technique for preparing seedbeds for pine in the New Jersey pine region, it has been used rather cautiously. Burning treatments have been made in the winter, when periodic light fires can be easily controlled. The treatments have been used almost exclusively on upland sites.

Implementing Lean Manufacturing in Malaysian Small and Medium Startup Pharmaceutical Company

Science.gov (United States)

Ibrahim, Wan Mohd Khairi bin Wan; Rahman, Mohamed Abdul; Abu Bakar, Mohd Rushdi bin

2017-03-01

Domestic pharmaceutical industry has been identified by the Malaysian government as an industry to be developed under its 11th economic development plan. Most homegrown pharmaceutical companies fall under the category of small and medium enterprises (SME) and therefore need to be highly efficient in their operations to compete with the multinationals. Though lean manufacturing is a well-known methodology to achieve an efficient operation, only a small percentage of the local SMEs implement it. The study aims to determine the real success factors in lean implementation through systematic review of relevant literature on lean manufacturing implementation in local companies, onsite observation of a selected SME company, Global Factor Sdn. Bhd. (GFSB), that successfully implemented lean manufacturing followed by actual implementation of lean project at IKOP Sdn. Bhd., a small startup pharmaceutical company. Lean tools like Gemba, value stream map (VSM) and spaghetti diagram were used to analyze and improve a process at IKOP Sdn. Bhd. The literature review showed that the implementation of lean manufacturing at Malaysian SMEs involved in pharmaceutical industry is at its infancy. Study at GFSB indicated that successful implementation of lean manufacturing stems from management support, employee’s commitment, government support and knowledge on lean among employees. Application of lean tools in IKOP Sdn. Bhd. to improve the process cycle efficiency of hand sanitizer, i-Hand 4.0, has shown that the GMP guidelines are not jeopardized. The Kaizen improvement project resulted in 46.3% reduction in lead time. It may be concluded that implementing lean manufacturing in any small local startup pharmaceutical company is beneficial in reducing operational costs and increasing the efficiency and effectiveness and does not conflict with the existing GMP guidelines.

Simulation-enhanced lean design process

Directory of Open Access Journals (Sweden)

Jon H. Marvel

2009-07-01

Full Text Available 72 Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} A traditional lean transformation process does not validate the future state before implementation, relying instead on a series of iterations to modify the system until performance is satisfactory. An enhanced lean process that includes future state validation before implementation is presented.  Simulation modeling and experimentation is proposed as the primary validation tool.  Simulation modeling and experimentation extends value stream mapping to include time, the behavior of individual entities, structural variability, random variability, and component interaction effects. Experiments to analyze the model and draw conclusions about whether the lean transformation effectively addresses the current state gap can be conducted.  Industrial applications of the enhanced lean process show it effectiveness.

Lean Government Methods Guide

Science.gov (United States)

This Guide focuses primarily on Lean production, which is an organizational improvement philosophy and set of methods that originated in manufacturing but has been expanded to government and service sectors.

Simulation of operational processes in hospital emergency units as lean healthcare tool

OpenAIRE

Gomes, Andreia Macedo; Vieira, Pedro Senna; Reis, Augusto da Cunha

2017-01-01

Recently, the Lean philosophy is gaining importance due to a competitive environment, which increases the need to reduce costs. Lean practices and tools have been applied to manufacturing, services, supply chain, startups and, the next frontier is healthcare. Most lean techniques can be easily adapted to health organizations. Therefore, this paper intends to summarize Lean practices and tools that are already being applied in health organizations. Among the numerous techniques and lean tools ...

The Effects of Application of Lean Concept in Retail

Directory of Open Access Journals (Sweden)

Radojko LUKIC

2012-06-01

Full Text Available Lean principles and techniques can be successfully applied in the retail sector. In the retail sector, lean approach improves operational flows. Lean retail encourages manufacturers to produce standard products in accordance with the created (placed orders from retailers pursuant to the demand of their consumers. Characteristics of the retail market are: strong competition, shorter product life cycle, longer product development time and high sensitivity of demand. In order to be more competitive and profitable today's retailers operate strategically oriented to lower prices and gain exemption from holding unnecessary stocks. Lean retail is an example of best practices of successful operational strategies which management need to accept - to maximize the operating efficiency of the retail process.

Chronic exercise preserves lean muscle mass in masters athletes.

Science.gov (United States)

Wroblewski, Andrew P; Amati, Francesca; Smiley, Mark A; Goodpaster, Bret; Wright, Vonda

2011-09-01

Aging is commonly associated with a loss of muscle mass and strength, resulting in falls, functional decline, and the subjective feeling of weakness. Exercise modulates the morbidities of muscle aging. Most studies, however, have examined muscle-loss changes in sedentary aging adults. This leaves the question of whether the changes that are commonly associated with muscle aging reflect the true physiology of muscle aging or whether they reflect disuse atrophy. This study evaluated whether high levels of chronic exercise prevents the loss of lean muscle mass and strength experienced in sedentary aging adults. A cross-section of 40 high-level recreational athletes ("masters athletes") who were aged 40 to 81 years and trained 4 to 5 times per week underwent tests of health/activity, body composition, quadriceps peak torque (PT), and magnetic resonance imaging of bilateral quadriceps. Mid-thigh muscle area, quadriceps area (QA), subcutaneous adipose tissue, and intramuscular adipose tissue were quantified in magnetic resonance imaging using medical image processing, analysis, and visualization software. One-way analysis of variance was used to examine age group differences. Relationships were evaluated using Spearman correlations. Mid-thigh muscle area (P = 0.31) and lean mass (P = 0.15) did not increase with age and were significantly related to retention of mid-thigh muscle area (P lean mass (P = 0.4) and PT. This study contradicts the common observation that muscle mass and strength decline as a function of aging alone. Instead, these declines may signal the effect of chronic disuse rather than muscle aging. Evaluation of masters athletes removes disuse as a confounding variable in the study of lower-extremity function and loss of lean muscle mass. This maintenance of muscle mass and strength may decrease or eliminate the falls, functional decline, and loss of independence that are commonly seen in aging adults.

Instill Lean A3 Thinking into Healthcare IT Services

Directory of Open Access Journals (Sweden)

Jihong Zeng

2014-08-01

Full Text Available Healthcare information technology is a key enabler for care transformation to provide quality care at low cost and better population health.  Many healthcare organizations have established IT Program Management and adopted ITIL best practice to manage IT services. However, ITIL and traditional project management are heavily process oriented, and neither flexible nor effective enough for swift response to changing business demand. Lean methodologies are increasingly deployed by healthcare providers to improve workflow process management but only has limited use cases documented in healthcare IT service. This paper introduces the Lean A3 Thinking methodology and its value in identifying and eliminating wastes to provide agile and effective solutions in response to customer requests. We present a case study of applying Lean A3 Thinking to improve clinical informatics reporting service. The initial evaluation results are promising and indicate that both ITIL and Lean A3 Thinking focus on customer and service quality, complementing each other well. ITIL provides a framework for ITSM based on a set of best practice to manage IT services. Lean A3 Thinking specifies a set of framework and tools for improving quality of services and processes by eliminating wastes. Proper balance between Lean and ITIL principles for ITSM needs more research and further study.

A Simulation of Lean Manufacturing: The Lean Lemonade Tycoon 2

Science.gov (United States)

Ncube, Lisa B.

2010-01-01

This article discusses the functions and effectiveness of games and simulations in the learning processes, in particular as an experiential learning methodology. The application of the game Lemonade Tycoon in the development of lean manufacturing concepts is described. This article addresses the use of the game to teach the principles of lean…

Effect of selection for lean growth on gonadal development of ...

African Journals Online (AJOL)

A primary objective of commercial pig production is lean meat yield in order to satisfy consumer needs. The majority of the commercial pig breeds in South Africa have been selected for high lean growth potential and reduced backfat thickness. There are indications that selection for high lean meat yield may affect the ...

Developing A Strategy to Enact Lean

Directory of Open Access Journals (Sweden)

Nicola Morrey

2013-01-01

Full Text Available This paper explains the strategy employed by a case study company to implement lean across the business, and to reflect on the success of this approach so other companies may consider this learning and how it might be useful to them. The strategy to enact lean in the case study company was based on creating a number of standard tools/ways of working. These tools can be considered to be standardised work for key aspects of the construction process that the company undertakes. The aim of the tools was to ensure that critical tasks would be carried out to the correct standard (quality, time, cost, health and safety every time, across the business. Achievement of this is expected to lead to improved performance and elimination of variation (waste. To implement this strategy of using standardised work to eliminate variation and lead to improved performance, a step-by-step process was developed to create the tools/standardised work. The paper describes the process that was undertaken and how it aimed to not only produce a number of tools/standardised work, but also to involve people and managers from across the business such that lean philosophy and thinking might also begin to become embedded. The paper will firstly explain, with reference to the relevant literature, how and why the strategy to implement standardised work was chosen, the process that was defined to develop the standardised work, and what happened when that process was put into practice. The findings of the paper show that whilst the completed tools delivered business benefits, the development of the tools did not follow the planned process. The paper discusses how people within the business responded to this strategy and how the process had to be continuously adapted to cope with the current business environment and path dependencies, further evidencing that lean implementations need to be tailored to suit the needs of the individual firm, rather than there being a one size fits all

Design thinking & lean