Superior Reproducibility of the Leading to Leading Edge and Inner to Inner Edge Methods in the Ultrasound Assessment of Maximum Abdominal Aortic Diameter

DEFF Research Database (Denmark)

Borgbjerg, Jens; Bøgsted, Martin; Lindholt, Jes S

2018-01-01

Objectives: Controversy exists regarding optimal caliper placement in ultrasound assessment of maximum abdominal aortic diameter. This study aimed primarily to determine reproducibility of caliper placement in relation to the aortic wall with the three principal methods: leading to leading edge...

Lead-lead isotope method. Application to migmatites and associaded rocks of the region of Sao Jose dos Campos, SP

International Nuclear Information System (INIS)

Babinski, M.

1988-01-01

Establishment of chemical and analytical procedures, preparation and purification of reagents and the mounting of a clean laboratory (class 100) for the Pb-Pb isotope dating of whole rock and mineral samples are discussed in this work. Two different methods of dissolution of rock samples and chemical separation of lead using anionic resin were tried in a conventional chemical laboratory using analytical grade reagents. The samples analysed were paleossome and neossome of migmatites from Sao Jose dos Campos, SP, and from the results obtained the analytical method to be employed was chosen. The results obtained by this method agree well with those of the Geochronology Laboratory at Oxford, for the same samples. Applying the established analytical procedure, migmatites and associated gneisses from the region of Sao Jose dos Campos were dated by Pb/Pb method. Some of the samples were also dated by Rb-Sr method. The lead-lead isochron age of 2355 +- 85 M.a. (μ 1 = 8.33) for the paleossome may be interpreted as the age of the metamorphism for these rocks, which were formed probably during the Archean. The age data for the phacoidal gneisses show a similar geological evolution, whereas the 2414 +- 800 M.A. Pb-Pb isochron age for the protomylonitic gneisses indicates a disturbed Pb-Pb isotope system. The neossome samples define a Pb-Pb isochron age of 1388 +- 290 M.A. (μ1 = 8.15), which may be interpreted as the age of migmatization. The calculated Pb-Pb ages for two alkali feldspars from the migmatites are devoid of any geological significance. The age values obtained by the Rb-Sr isotope system for the neossome and paleossome of the migmatites agree with the Pb/Pb data within experimental errors. However, the study shows that results of the Rb-Sr data alone cannot be interpreted unambiguously with out comparison with data from other isotope systems. (author) [pt

A combined method to estimate the appropriate age value of closed uraniun-lead system

International Nuclear Information System (INIS)

Malakhov, S.S.

1982-01-01

A new method is proposed for obtaining the appropriate age values of closed uranium-lead systems taking into account total indeependent information delivered as a result of spectral and isotope-lead analyses. A simple mathematical apparatus which permits to perform a geochronological interpretation of samples using miniature computers is considered and suggested. A simple estimation formula for determining the age of uranium-lead systems under the assumption of model development of isotope ratios of ordinary lead is derived and tested basing on the facts

Method and Apparatus for a Leading Edge Slat on a Wing of an Aircraft

Science.gov (United States)

Pitt, Dale M. (Inventor); Eckstein, Nicholas Stephen (Inventor)

2013-01-01

A method and apparatus for managing a flight control surface system. A leading edge device is moved on a leading edge from an undeployed position to a deployed position. The leading edge device has an outer surface, an inner surface, and a deformable fairing attached to the leading edge device such that the deformable fairing covers at least a portion of the inner surface. The deformable fairing changes from a deformed shape to an original shape when the leading edge device is moved to the deployed position. The leading edge device is then moved from the deployed position to the undeployed position, wherein the deformable fairing changes from the original shape to the deformed shape.

Utilizing the Lead User Method for Promoting Innovation in E-Recuiting

NARCIS (Netherlands)

Furtmueller-Ettinger, Elfriede; Wilderom, Celeste P.M.; van Dick, Rolf; Bondarouk, Tatiana; Ruel, Hubertus Johannes Maria; Guiderdoni-Jourdain, Karine; Oiry, Ewan

2009-01-01

In order to maintain their customer base, many e-recruiting firms are in need of developing innovations. The Lead User (LU) Method has been heralded in the new product innovation literature but not yet applied often in e-service settings. Based on an e-recruiting portal, the authors compare new

Application of proton-induced X-ray emission method to determination of lead content in blood

International Nuclear Information System (INIS)

Slominska, D.; Jarczyk, L.; Rokita, E.; Strzalkowski, A.; Losiowski, A.; Macheta, A.; Sych, M.; Moszkowicz, S.

1979-01-01

The proton induced X-ray emission method is applied for determination of lead content in the blood of the people exposed to contact with ethyline vapours and people working in lead-zinc works. (author)

A fence barrier method of leading edge cell capture for explorative biochemical research.

Science.gov (United States)

Wager, Lucas J; Murray, Rachael Z; Thompson, Erik W; Leavesley, David I

2017-09-03

The scratch or wound-healing assay is used ubiquitously for investigating re-epithelialisation and has already revealed the importance of cells comprising the leading edge of healing epithelial wounds. However it is currently limited to studying the effect of known biochemical agents on the tissue of choice. Here we present an adaptation that extends the utility of this model to encompass the collection of cells from the leading edge of migrating epithelial sheets making available explorative biochemical analyses. The method is scalable and does not require expensive apparatus, making it suitable for large and small laboratories alike. We detail the application of our method and exemplify proof of principle data derived from primary human keratinocyte cultures.

Synthesis of Lead Sulfide Nanoparticles by Chemical Precipitation Method

International Nuclear Information System (INIS)

Chongad, L S; Sharma, A; Banerjee, M; Jain, A

2016-01-01

Lead sulfide (PbS) nanoparticles were prepared by chemical precipitation method (CPM) with the assistance of H 2 S gas. The microstructure and morphology of the synthesized nanoparticles have been investigated using X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD patterns of the PbS nanoparticles reveal formation of cubic phase. To investigate the quality of prepared nanoparticles, the particles size, lattice constant, strain, dislocation density etc. have been determined using XRD. TEM images reveal formation of cubic nanoparticles and the particle size determined from TEM images agree well with those from XRD. (paper)

Low temperature synthesis & characterization of lead-free BCZT ceramics using molten salt method

Science.gov (United States)

Jai Shree, K.; Chandrakala, E.; Das, Dibakar

2018-04-01

Piezoelectric properties are greatly influenced by the synthesis route, microstructure, stoichiometry of the chemical composition, purity of the starting materials. In this study, molten salt method was used to prepare lead-free BCZT ceramics. Molten salt method is one of the simplestmethods to prepare chemically-purified, single phase powders in high yield often at lower temperatures and shorten reaction time. Calcination of the molten salt synthesized powders resulted in asingle-phase perovskite structure at 1000 °C which is ˜ 350 °C less than the conventional solid-sate reaction method. With increasing calcination temperature the average template size was increased (˜ 0.5-2 µm). Formation of well dispersive templates improves the sinterability at lower temperatures. Lead-free BCZT ceramics sintered at 1500 °C for 2 h resulted in homogenous and highly dense microstructure with ˜92% of the theoretical density and a grain size of ˜ 35 µm. This highly dense microstructure could enhance the piezoelectric properties of the system.

Virtual screening methods as tools for drug lead discovery from large chemical libraries.

Science.gov (United States)

Ma, X H; Zhu, F; Liu, X; Shi, Z; Zhang, J X; Yang, S Y; Wei, Y Q; Chen, Y Z

2012-01-01

Virtual screening methods have been developed and explored as useful tools for searching drug lead compounds from chemical libraries, including large libraries that have become publically available. In this review, we discussed the new developments in exploring virtual screening methods for enhanced performance in searching large chemical libraries, their applications in screening libraries of ~ 1 million or more compounds in the last five years, the difficulties in their applications, and the strategies for further improving these methods.

The optimum lead thickness for lead-activation detectors

International Nuclear Information System (INIS)

Si Fenni; Hu Qingyuan

2009-01-01

The optimum lead thickness for lead-activation detectors has been studied in this paper. First existence of the optimum lead thickness is explained theoretically. Then the optimum lead thickness is obtained by two methods, MCNP5 calculation and mathematical estimation. At last factors which affect the optimum lead thickness are discussed. It turns out that the optimum lead thickness is irrelevant to incident neutron energies. It is recommended 2.5 cm generally.

A Time-Walk Correction Method for PET Detectors Based on Leading Edge Discriminators.

Science.gov (United States)

Du, Junwei; Schmall, Jeffrey P; Judenhofer, Martin S; Di, Kun; Yang, Yongfeng; Cherry, Simon R

2017-09-01

The leading edge timing pick-off technique is the simplest timing extraction method for PET detectors. Due to the inherent time-walk of the leading edge technique, corrections should be made to improve timing resolution, especially for time-of-flight PET. Time-walk correction can be done by utilizing the relationship between the threshold crossing time and the event energy on an event by event basis. In this paper, a time-walk correction method is proposed and evaluated using timing information from two identical detectors both using leading edge discriminators. This differs from other techniques that use an external dedicated reference detector, such as a fast PMT-based detector using constant fraction techniques to pick-off timing information. In our proposed method, one detector was used as reference detector to correct the time-walk of the other detector. Time-walk in the reference detector was minimized by using events within a small energy window (508.5 - 513.5 keV). To validate this method, a coincidence detector pair was assembled using two SensL MicroFB SiPMs and two 2.5 mm × 2.5 mm × 20 mm polished LYSO crystals. Coincidence timing resolutions using different time pick-off techniques were obtained at a bias voltage of 27.5 V and a fixed temperature of 20 °C. The coincidence timing resolution without time-walk correction were 389.0 ± 12.0 ps (425 -650 keV energy window) and 670.2 ± 16.2 ps (250-750 keV energy window). The timing resolution with time-walk correction improved to 367.3 ± 0.5 ps (425 - 650 keV) and 413.7 ± 0.9 ps (250 - 750 keV). For comparison, timing resolutions were 442.8 ± 12.8 ps (425 - 650 keV) and 476.0 ± 13.0 ps (250 - 750 keV) using constant fraction techniques, and 367.3 ± 0.4 ps (425 - 650 keV) and 413.4 ± 0.9 ps (250 - 750 keV) using a reference detector based on the constant fraction technique. These results show that the proposed leading edge based time-walk correction method works well. Timing resolution obtained

Method of determining paper-deposited materials, eg. lead, by their reaction with radioactive krypton

International Nuclear Information System (INIS)

Tolgyessy, J.; Pruzinec, J.

1976-01-01

The invention claims a method of determining substances on a paper carrier based on the substance reaction with 85 Kr gas and the measurement of radioactivity of the kryptonate formed. Lead is shown as an example. Different amounts of lead acetate were deposited on Whatman 2 chromatographic paper as was an unknown sample of Pb salt. The paper was exposed to a 2.5 mCi 85 Kr atmosphere for 48 hours. The activity of the individual spots was then measured, a calibration curve established and the amount of lead in the analyzed sample read-out. (Ha)

Common ECG Lead Placement Errors. Part I: Limb Lead Reversals

Directory of Open Access Journals (Sweden)

Allison V. Rosen

2015-10-01

Full Text Available Background: Electrocardiography (ECG is a very useful diagnostic tool. However, errors in placement of ECG leads can create artifacts, mimic pathologies, and hinder proper ECG interpretation. It is important for members of the health care team to be able to recognize the common patterns resulting from lead placement errors. Methods: 12-lead ECGs were recorded in a single male healthy subject in his mid 20s. Six different limb lead reversals were compared to ECG recordings from correct lead placement. Results: Classic ECG patterns were observed when leads were reversed. Methods of discriminating these ECG patterns from true pathologic findings were described. Conclusion: Correct recording and interpretation of ECGs is key to providing optimal patient care. It is therefore crucial to be able to recognize common ECG patterns that are indicative of lead reversals.

LEADING WITH LEADING INDICATORS

International Nuclear Information System (INIS)

PREVETTE, S.S.

2005-01-01

This paper documents Fluor Hanford's use of Leading Indicators, management leadership, and statistical methodology in order to improve safe performance of work. By applying these methods, Fluor Hanford achieved a significant reduction in injury rates in 2003 and 2004, and the improvement continues today. The integration of data, leadership, and teamwork pays off with improved safety performance and credibility with the customer. The use of Statistical Process Control, Pareto Charts, and Systems Thinking and their effect on management decisions and employee involvement are discussed. Included are practical examples of choosing leading indicators. A statistically based color coded dashboard presentation system methodology is provided. These tools, management theories and methods, coupled with involved leadership and employee efforts, directly led to significant improvements in worker safety and health, and environmental protection and restoration at one of the nation's largest nuclear cleanup sites

Involving Lead Users in Innovation

DEFF Research Database (Denmark)

Brem, Alexander; Bilgram, Volker; Gutstein, Adele

2018-01-01

Research on the lead user method has been conducted for more than thirty years and has shown that the method is more likely to generate breakthrough innovation than traditional market research tools. Based on a systematic literature review, this paper shows a detailed view on the broad variety...... of research on lead user characteristics, lead user processes, lead user identification and application, and success factors. The main challenge of the lead user method as identified in literature is the resource issue regarding time, manpower, and costs. Also, internal acceptance and the processing...... of the method have been spotted in literature, as well as the intellectual property protection issue. From the starting point of the initial lead user method process introduced by Lüthje and Herstatt (2004), results are integrated into a revisited view on the lead user method process. In addition, concrete...

Outside corner and method of making in the making lead brick (plain brick) using rotary table

International Nuclear Information System (INIS)

Muhammad Awwaluddin; Samuel Praptoyo

2009-01-01

It has been developed a tool that can be used for defining angles on the fabrication of lead bricks. The angles are both outside of the lead bricks that correspond to male and female shape respectively. The lead bricks should be in accordance to ISO 7212-1986 standard which has angle tolerance 90° 0 +15 for male and 90° 0 -15 for female. The accuracy of these angles is very important to maintain the equilibrium position of the bricks so that their arrangement will not lining or collapse. A rotary table is used for the fabrication to make easier in setting up any related working apparatus and to have precision measurement result. However, a lot of operator do not know yet how to operate such a rotary table to produce angle with such an eligible tolerance. Therefore, a method of measurement in machining lead brick process using a rotary table is necessarily required. This method will be used as a reference to have angle accuracy of 0,03° in producing outside and inside angles or male and female lead bricks. (author)

ADVANCEMENTS IN TIME-SPECTRA ANALYSIS METHODS FOR LEAD SLOWING-DOWN SPECTROSCOPY

International Nuclear Information System (INIS)

Smith, Leon E.; Anderson, Kevin K.; Gesh, Christopher J.; Shaver, Mark W.

2010-01-01

Direct measurement of Pu in spent nuclear fuel remains a key challenge for safeguarding nuclear fuel cycles of today and tomorrow. Lead slowing-down spectroscopy (LSDS) is an active nondestructive assay method that has the potential to provide independent, direct measurement of Pu and U isotopic mass with an uncertainty lower than the approximately 10 percent typical of today's confirmatory assay methods. Pacific Northwest National Laboratory's (PNNL) previous work to assess the viability of LSDS for the assay of pressurized water reactor (PWR) assemblies indicated that the method could provide direct assay of Pu-239 and U-235 (and possibly Pu-240 and Pu-241) with uncertainties less than a few percent, assuming suitably efficient instrumentation, an intense pulsed neutron source, and improvements in the time-spectra analysis methods used to extract isotopic information from a complex LSDS signal. This previous simulation-based evaluation used relatively simple PWR fuel assembly definitions (e.g. constant burnup across the assembly) and a constant initial enrichment and cooling time. The time-spectra analysis method was founded on a preliminary analytical model of self-shielding intended to correct for assay-signal nonlinearities introduced by attenuation of the interrogating neutron flux within the assembly.

A fast method for the determination of lead in honey samples using stabilizer-free silver nanoparticles

Science.gov (United States)

Bittar, Dayana Borges; Catelani, Tiago Augusto; Pezza, Leonardo; Pezza, Helena Redigolo

2018-01-01

A sensitive, rapid and robust method based on the use of stabilizer-free silver nanoparticles was developed for lead detection in honey. Silver nanoparticles were synthesized without the presence of any stabilizers using silver nitrate and sodium borohydride as precursors where the latter was applied as reducing agent. The optimization of the experimental variables (AgNO3 and NaBH4) for the formation of the nanoparticles was carried out using varying volumes of these solutions. Spectrophotometric measurements at 393 nm showed a linear working range between 0.0500 and 0.167 mg L- 1 lead (R = 0.994), with limits of detection (LOD) and quantification (LOQ) of 0.0135 and 0.0451 mg L- 1, respectively. The proposed method proved to be a significantly sensitive mechanism for lead detection in honey samples.

The effect of different propolis harvest methods on its lead contents determined by ET AAS and UV-visS

Energy Technology Data Exchange (ETDEWEB)

Sales, A. [Department of Analytical Chemistry, Faculty of Biochemistry, Chemistry and Pharmacy, National University of Tucuman, Ayacucho 471, 4000 Tucuman (Argentina)]. E-mail: amsales@fbqf.unt.edu.ar; Alvarez, A. [National Institute of Agricultural Technology (INTA), Experimental Station Famailla, Ruta 301, Km 32, Famailla, Tucuman (Argentina); Areal, M. Rodriguez [Department of Analytical Chemistry, Faculty of Biochemistry, Chemistry and Pharmacy, National University of Tucuman, Ayacucho 471, 4000 Tucuman (Argentina); Maldonado, L. [National Institute of Agricultural Technology (INTA), Experimental Station Famailla, Ruta 301, Km 32, Famailla, Tucuman (Argentina); Marchisio, P. [Department of Analytical Chemistry, Faculty of Biochemistry, Chemistry and Pharmacy, National University of Tucuman, Ayacucho 471, 4000 Tucuman (Argentina); Rodriguez, M. [Department of Analytical Chemistry, Faculty of Biochemistry, Chemistry and Pharmacy, National University of Tucuman, Ayacucho 471, 4000 Tucuman (Argentina); Bedascarrasbure, E. [National Institute of Agricultural Technology (INTA), Experimental Station Famailla, Ruta 301, Km 32, Famailla, Tucuman (Argentina)

2006-10-11

Argentinean propolis is exported to different countries, specially Japan. The market demands propolis quality control according to international standards. The analytical determination of some metals, as lead in food, is very important for their high toxicity even in low concentrations and because of their harmful effects on health. Flavonoids, the main bioactive compounds of propolis, tend to chelate metals as lead, which becomes one of the main polluting agents of propolis. The lead found in propolis may come from the atmosphere or it may be incorporated in the harvest, extraction and processing methods. The aim of this work is to evaluate lead level on Argentinean propolis determined by electrothermal atomic absorption spectrometry (ET AAS) and UV-vis spectrophotometry (UV-visS) methods, as well as the effect of harvest methods on those contents. A randomized test with three different treatments of collection was made to evaluate the effect of harvest methods. These procedures were: separating wedges (traditional), netting plastic meshes and stamping out plastic meshes. By means of the analysis of variance technique for multiple comparisons (ANOVA) it was possible to conclude that there are significant differences between scraped and mesh methods (stamped out and mosquito netting meshes). The results obtained in the present test would allow us to conclude that mesh methods are more advisable than scraped ones in order to obtain innocuous and safe propolis with minor lead contents. A statistical comparison of lead determination by both, ET AAS and UV-visS methods, demonstrated that there is not a significant difference in the results achieved with the two analytical techniques employed.

SPECIFIC MANAGEMENT AND LEADING METHODS APPLIED TO BUTTERFLY TOURISM FOR 2012

Directory of Open Access Journals (Sweden)

Eugenia ALECU

2013-12-01

Full Text Available In this paper are explained the most important management elements for managers and employees of a tour operator agency. The study showed in a concrete and realistic manner how a manager of a tour operator agency can lead, control, predict and determine the prospects utilizing a specific management method called dashboard. Given the competition in the field of tourism, Butterfly Tourism is trying to manage its business in a professional manner and offer attractive packages and favorable prices to its customers.

Development and validation of a novel, simple, and accurate spectrophotometric method for the determination of lead in human serum.

Science.gov (United States)

Shayesteh, Tavakol Heidari; Khajavi, Farzad; Khosroshahi, Abolfazl Ghafuri; Mahjub, Reza

2016-01-01

The determination of blood lead levels is the most useful indicator of the determination of the amount of lead that is absorbed by the human body. Various methods, like atomic absorption spectroscopy (AAS), have already been used for the detection of lead in biological fluid, but most of these methods are based on complicated, expensive, and highly instructed instruments. In this study, a simple and accurate spectroscopic method for the determination of lead has been developed and applied for the investigation of lead concentration in biological samples. In this study, a silica gel column was used to extract lead and eliminate interfering agents in human serum samples. The column was washed with deionized water. The pH was adjusted to the value of 8.2 using phosphate buffer, and then tartrate and cyanide solutions were added as masking agents. The lead content was extracted into the organic phase containing dithizone as a complexion reagent and the dithizone-Pb(II) complex was formed and approved by visible spectrophotometry at 538 nm. The recovery was found to be 84.6 %. In order to validate the method, a calibration curve involving the use of various concentration levels was calculated and proven to be linear in the range of 0.01-1.5 μg/ml, with an R (2) regression coefficient of 0.9968 by statistical analysis of linear model validation. The largest error % values were found to be -5.80 and +11.6 % for intra-day and inter-day measurements, respectively. The largest RSD % values were calculated to be 6.54 and 12.32 % for intra-day and inter-day measurements, respectively. Further, the limit of detection (LOD) was calculated to be 0.002 μg/ml. The developed method was applied to determine the lead content in the human serum of voluntary miners, and it has been proven that there is no statistically significant difference between the data provided from this novel method and the data obtained from previously studied AAS.

A on-line method for the determination of lead and lead isotope ratios in fresh and saline waters by inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Halicz, Ludwik; Lam, J.W.H.; McLaren, J.W.

1994-01-01

A previously reported on-line ICP-MS method for the determination of lead and other trace elements in seawater has been re-examined to determine its suitability for the determination of lead isotope ratios ( 206 Pb/ 207 Pb and 207 Pb/ 208 Pb) in fresh and saline natural waters. A detection limit of 0.9 ng/1 for total lead (for a 5 ml sample) was achieved. Precision of isotope ratio data was 0.2-0.3% RSD at a Pb concentration of 1 μg/l, and was still better than 2% at concentrations of only 10-40 ng/1 in seawater certified reference materials (CRMs). For all three natural water CRMs examined, measured precision was very close to the limit predicted by counting statistics. (Author)

Preparation of lead oxide nanoparticles from cathode-ray tube funnel glass by self-propagating method.

Science.gov (United States)

Wang, Yu; Zhu, Jianxin

2012-05-15

This paper presents a novel process of extracting lead oxide nanoparticles from cathode-ray tube (CRT) funnel glass using self-propagating high-temperature synthesis (SHS) method. The impacts of added amount of funnel glass on the extraction ratio of lead, the lead extraction velocity and the micromorphology, as well as particle size of extracted nanoparticles were investigated. We found that self-propagating reaction in the presence of Mg and Fe(2)O(3) could separate lead preferentially and superfine lead oxide nanoparticles were obtained from a collecting chamber. The separation ratio was related closely to the amount of funnel glass added in the original mixture. At funnel glass addition of no more than 40wt.%, over 90wt.% of lead was recovered from funnel glass. High extraction yield reveals that the network structure of funnel glass was fractured due to the dramatic energy generated during the SHS melting process. The PbO nanoparticles collected show good dispersion and morphology with a mean grain size of 40-50nm. Copyright © 2012 Elsevier B.V. All rights reserved.

Three-stage method for interpretation of uranium-lead isotopic data

International Nuclear Information System (INIS)

Nejmark, L.A.; Ovchinnikova, G.V.; Levchenkov, O.A.

1982-01-01

Three-dimensional approach for the iterpretation of uranium-lead isoto e ratios in pnatural systems, development of which corresponds to three stages, has been considered. In the framework of the three-stage model two cases, differing in the character of uranium-lead systems violation at the beginning of the third stage, are discussed. The first case corresponds to uranium addition or lead substraction, and the second one - to addition of lead of unknown isotopic content. Three-stage approach permits without amending the isotopic content of lead captured during crystallization to calculated the beginning of the second and third stages of uranium-lead systems development and to evaluate parameters of lead added to the system. Concrete examples of interpretation of uranium-lead isotopic ratios in minerals and rock samples as a whole both of the terrestrial and cosmic origin are considered. Possibilities and limitations of the three-stage approach are analyzed and directions of further development are outlined

Removal of lead ions from industrial waste water by using biomaterials – a novel method

Directory of Open Access Journals (Sweden)

Malairajan Singanan

2005-12-01

Full Text Available A simple cost effective and eco-friendly method for the remediation of lead from industrial wastewater has been investigated. A novel biomaterial, Tridax procumbens (Asteraceae a medicinal plant, was used for the removal of lead ions from synthetic wastewater and the method was also applied for real sample analysis. The operational pH of the experimental solution was fixed as 4.5. The optimum amount of bioadsorbent was 3.5 g. The Pb(II ions removal efficiency of the raw bioadsorbent was also determined. The removal efficiency of the activated carbon of the bioadsorbent was excellent. 98 % removal of Pb(II ions was achieved at the dose rate of 3.5 g. The optimum contact time was estimated to be 160 minutes.

Standard test method for graphite furnace atomic absorption spectrometric determination of lead and cadmium extracted from ceramic foodware

CERN Document Server

American Society for Testing and Materials. Philadelphia

2000-01-01

1.1 This test method covers procedures for using graphite furnace atomic absorption spectroscopy (GFAAS) to quantitatively determine lead and cadmium extracted by acetic acid at room temperature from the food-contact surface of foodware. The method is applicable to food-contact surfaces composed of silicate-based materials (earthenware, glazed ceramicware, decorated ceramicware, decorated glass, and lead crystal glass) and is capable of determining lead concentrations greater than 0.005 to 0.020 g/mL and cadmium concentrations greater than 0.0005 to 0.002 g/mL, depending on instrument design. 1.2 This test method also describes quality control procedures to check for contamination and matrix interference during GFAAS analyses and a specific sequence of analytical measurements that demonstrates proper instrument operation during the time period in which sample solutions are analyzed. 1.3 Cleaning and other contamination control procedures are described in this test method. Users may modify contamination cont...

A novel method for direct solder bump pull testing using lead-free solders

Science.gov (United States)

Turner, Gregory Alan

This thesis focuses on the design, fabrication, and evaluation of a new method for testing the adhesion strength of lead-free solders, named the Isotraction Bump Pull method (IBP). In order to develop a direct solder joint-strength testing method that did not require customization for different solder types, bump sizes, specific equipment, or trial-and-error, a combination of two widely used and accepted standards was created. First, solder bumps were made from three types of lead free solder were generated on untreated copper PCB substrates using an in-house fabricated solder bump-on-demand generator, Following this, the newly developed method made use of a polymer epoxy to encapsulate the solder bumps that could then be tested under tension using a high precision universal vertical load machine. The tests produced repeatable and predictable results for each of the three alloys tested that were in agreement with the relative behavior of the same alloys using other testing methods in the literature. The median peak stress at failure for the three solders tested were 2020.52 psi, 940.57 psi, and 2781.0 psi, and were within one standard deviation of the of all data collected for each solder. The assumptions in this work that brittle fracture occurred through the Intermetallic Compound layer (IMC) were validated with the use of Energy-Dispersive X-Ray Spectrometry and high magnification of the fractured surface of both newly exposed sides of the test specimens. Following this, an examination of the process to apply the results from the tensile tests into standard material science equations for the fracture of the systems was performed..

Determination of Trace Amounts of Lead with ETAAS After Single Drop Microextraction and Dispersive Liquid Liquid Microextraction Methods

Directory of Open Access Journals (Sweden)

Efeçınar M.

2013-04-01

Full Text Available Two liquid-phase microextraction procedures, single-drop microextraction (SDME and dispersive liquid–liquid microextraction (DLLME, have been developed for the determination of lead by electrothermal atomic absorption spectrometry (ETAAS. Both methods were based on the formation of lead iodide-Rhodamine B complex which is in phosphoric acid medium. In the presence of KI, anionic lead iodide was complexed with Rhodamine B as an ion-association complex. Several factors that may be affected on the SDME and DLLME methods were optimized. In the optimum experimental conditions, the limit of detection (3s and the enhancement factor were 0.008 μgL−1 and 152 for SDME and 0.0129 μgL−1 and 89 for DLLME respectively. The relative standard deviation (RSD for eight replicate determinations of 0.25 μgL−1 Pb was 4.6% for SDME and 0.5 μgL−1 Pb was 2.9% for DLLME. The developed methods were validated by the analysis of certified reference materials, and applied successfully to the determination of lead in several water and food samples.

Computational Methods Used in Hit-to-Lead and Lead Optimization Stages of Structure-Based Drug Discovery.

Science.gov (United States)

Heifetz, Alexander; Southey, Michelle; Morao, Inaki; Townsend-Nicholson, Andrea; Bodkin, Mike J

2018-01-01

GPCR modeling approaches are widely used in the hit-to-lead (H2L) and lead optimization (LO) stages of drug discovery. The aims of these modeling approaches are to predict the 3D structures of the receptor-ligand complexes, to explore the key interactions between the receptor and the ligand and to utilize these insights in the design of new molecules with improved binding, selectivity or other pharmacological properties. In this book chapter, we present a brief survey of key computational approaches integrated with hierarchical GPCR modeling protocol (HGMP) used in hit-to-lead (H2L) and in lead optimization (LO) stages of structure-based drug discovery (SBDD). We outline the differences in modeling strategies used in H2L and LO of SBDD and illustrate how these tools have been applied in three drug discovery projects.

Extending the Matrix Element Method beyond the Born approximation: calculating event weights at next-to-leading order accuracy

International Nuclear Information System (INIS)

Martini, Till; Uwer, Peter

2015-01-01

In this article we illustrate how event weights for jet events can be calculated efficiently at next-to-leading order (NLO) accuracy in QCD. This is a crucial prerequisite for the application of the Matrix Element Method in NLO. We modify the recombination procedure used in jet algorithms, to allow a factorisation of the phase space for the real corrections into resolved and unresolved regions. Using an appropriate infrared regulator the latter can be integrated numerically. As illustration, we reproduce differential distributions at NLO for two sample processes. As further application and proof of concept, we apply the Matrix Element Method in NLO accuracy to the mass determination of top quarks produced in e"+e"− annihilation. This analysis is relevant for a future Linear Collider. We observe a significant shift in the extracted mass depending on whether the Matrix Element Method is used in leading or next-to-leading order.

The lead-lag relationship between stock index and stock index futures: A thermal optimal path method

Science.gov (United States)

Gong, Chen-Chen; Ji, Shen-Dan; Su, Li-Ling; Li, Sai-Ping; Ren, Fei

2016-02-01

The study of lead-lag relationship between stock index and stock index futures is of great importance for its wide application in hedging and portfolio investments. Previous works mainly use conventional methods like Granger causality test, GARCH model and error correction model, and focus on the causality relation between the index and futures in a certain period. By using a non-parametric approach-thermal optimal path (TOP) method, we study the lead-lag relationship between China Securities Index 300 (CSI 300), Hang Seng Index (HSI), Standard and Poor 500 (S&P 500) Index and their associated futures to reveal the variance of their relationship over time. Our finding shows evidence of pronounced futures leadership for well established index futures, namely HSI and S&P 500 index futures, while index of developing market like CSI 300 has pronounced leadership. We offer an explanation based on the measure of an indicator which quantifies the differences between spot and futures prices for the surge of lead-lag function. Our results provide new perspectives for the understanding of the dynamical evolution of lead-lag relationship between stock index and stock index futures, which is valuable for the study of market efficiency and its applications.

Extending the Matrix Element Method beyond the Born approximation: calculating event weights at next-to-leading order accuracy

Energy Technology Data Exchange (ETDEWEB)

Martini, Till; Uwer, Peter [Humboldt-Universität zu Berlin, Institut für Physik,Newtonstraße 15, 12489 Berlin (Germany)

2015-09-14

In this article we illustrate how event weights for jet events can be calculated efficiently at next-to-leading order (NLO) accuracy in QCD. This is a crucial prerequisite for the application of the Matrix Element Method in NLO. We modify the recombination procedure used in jet algorithms, to allow a factorisation of the phase space for the real corrections into resolved and unresolved regions. Using an appropriate infrared regulator the latter can be integrated numerically. As illustration, we reproduce differential distributions at NLO for two sample processes. As further application and proof of concept, we apply the Matrix Element Method in NLO accuracy to the mass determination of top quarks produced in e{sup +}e{sup −} annihilation. This analysis is relevant for a future Linear Collider. We observe a significant shift in the extracted mass depending on whether the Matrix Element Method is used in leading or next-to-leading order.

Uranium-lead systematics

International Nuclear Information System (INIS)

Wickman, F.E.

1983-01-01

The method of Levchenkov and Shukolyukov for calculating age and time disturbance of minerals without correction for original lead is generalized to include the cases when (1) original lead and radiogenic lead leach differently, and (2) the crystals studied consist of a core and a mantle. It is also shown that a straight line obtained from the solution of the equations is the locus of the isotopic composition of original lead. (Auth.)

Lead user projects in practice

DEFF Research Database (Denmark)

Brem, Alexander; Gutstein, Adele

2018-01-01

Earlier research on the lead user method is focused on individual case studies and how the method was applied in a specific context. In this paper, we take a broader approach, analyzing a sample of 24 lead user projects, which included working with 188 lead users. These projects were analyzed...

Evaluation method of lead measurement accuracy of gears using a wedge artefact

International Nuclear Information System (INIS)

Komori, Masaharu; Takeoka, Fumi; Kubo, Aizoh; Okamoto, Kazuhiko; Osawa, Sonko; Sato, Osamu; Takatsuji, Toshiyuki

2009-01-01

The reduction of the vibration and noise of gears is an important issue in mechanical devices such as vehicles and wind turbines. The characteristics of the vibration and noise of gears are markedly affected by deviations of the tooth flank form of micrometre order; therefore, a strict quality control of the tooth flank form is required. The accuracy of the lead measurement for a gear-measuring instrument is usually evaluated using a master gear or a lead master. However, it is difficult to manufacture masters with high accuracy because the helix is a complicated geometrical form. In this paper, we propose a method of evaluating a gear-measuring instrument using a wedge artefact, which includes a highly precise plane surface. The concept of the wedge artefact is described and a mathematical model of the measuring condition of the wedge artefact is constructed. Theoretical measurement results for the wedge artefact are calculated. The wedge artefact is designed and produced on the basis of the theoretical measurement results. A measurement experiment using the wedge artefact is carried out and its effectiveness is verified

Iodide-assisted total lead measurement and determination of different lead fractions in drinking water samples.

Science.gov (United States)

Zhang, Yuanyuan; Ng, Ding-Quan; Lin, Yi-Pin

2012-07-01

Lead and its compounds are toxic and can harm human health, especially the intelligence development in children. Accurate measurement of total lead present in drinking water is crucial in determining the extent of lead contamination and human exposure due to drinking water consumption. The USEPA method for total lead measurement (no. 200.8) is often used to analyze lead levels in drinking water. However, in the presence of high concentration of the tetravalent lead corrosion product PbO(2), the USEPA method was not able to fully recover particulate lead due to incomplete dissolution of PbO(2) particles during strong acid digestion. In this study, a new procedure that integrates membrane separation, iodometric PbO(2) measurement, strong acid digestion and ICP-MS measurement was proposed and evaluated for accurate total lead measurement and quantification of different lead fractions including soluble Pb(2+), particulate Pb(II) carbonate and PbO(2) in drinking water samples. The proposed procedure was evaluated using drinking water reconstituted with spiked Pb(2+), spiked particulate Pb(II) carbonate and in situ formed or spiked PbO(2). Recovery tests showed that the proposed procedure and the USEPA method can achieve 93-112% and 86-103% recoveries respectively for samples containing low PbO(2) concentrations (0.018-0.076 mg Pb per L). For samples containing higher concentrations of PbO(2) (0.089-1.316 mg Pb per L), the USEPA method failed to meet the recovery requirement for total lead (85-115%) while the proposed method can achieve satisfactory recoveries (91-111%) and differentiate the soluble Pb(2+), particulate Pb(II) carbonate and PbO(2).

Development of stable solidification methods for toxic lead oxide in radioactive wastes

International Nuclear Information System (INIS)

Hitoshi Mimura; Shingo Ikeda; Yuichi Niibori

2009-01-01

The objective of this study is to develop the advanced solidification methods for the toxic lead oxide contained in radioactive wastes and to examine their chemical durability in terms of leachability and surface alteration; the solidification characteristics and leachability for the following three kinds of solidified products immobilizing lead were examined, and the experimental results were summarized as follows. (a) Mineral solidified products: A-zeolite or fly ash (FA) was used as a binder, and NaAlO 2 and Na 2 SiO 3 were mixed as additives. The leachability of lead ions in pure water was considerably lowered by the heat treatment at higher temperature (1,000 degree C), and the concentration of lead ions leached was under criterion value of 0.3 mg/l. The products prepared by mixing A-zeolite and fly ash also had low leachability under 0.3 mg/l even in the saturated Ca(OH)2 solution. (b) Melted solidified products: A-zeolite or fly ash was used as a binder and glass-forming reagents of B 2 O 3 and NaH 2 PO 4 were used as additives. The XRD peaks assigned PbO were not observed in all products. The products for the mixtures of FA:NaH 2 PO 4 :PbO (2:2:1 and 3:1:1) had low leachability under criterion value in both leachants of deionized water and saturated Ca(OH) 2 solution. (c) Phosphate ceramics products: the chemically bonded phosphate ceramics were produced by using MgKPO 4 , MgHPO 4 , Zr(HPO 4 ) 2 , potassium iron phosphate and sodium iron phosphate, and FA was used as additives. In particular, by using MgHPO 4 , the leachability of the products was lowered less than 0.3 mg/l in both leachants. The phosphate ceramics products and melted solidified products are favorable as the waste solid forms immobilizing lead. In particular, novel ceramics products have advantages in the simple solidification procedure similarly to the cement products. As for mineral solidification, natural zeolites and FA as binder also useful from the viewpoint of cost efficiency

Superior Reproducibility of the Leading to Leading Edge and Inner to Inner Edge Methods in the Ultrasound Assessment of Maximum Abdominal Aortic Diameter.

Science.gov (United States)

Borgbjerg, Jens; Bøgsted, Martin; Lindholt, Jes S; Behr-Rasmussen, Carsten; Hørlyck, Arne; Frøkjær, Jens B

2018-02-01

Controversy exists regarding optimal caliper placement in ultrasound assessment of maximum abdominal aortic diameter. This study aimed primarily to determine reproducibility of caliper placement in relation to the aortic wall with the three principal methods: leading to leading edge (LTL), inner to inner edge (ITI), and outer to outer edge (OTO). The secondary aim was to assess the mean difference between the OTO, ITI, and LTL diameters and estimate the impact of using either of these methods on abdominal aortic aneurysm (AAA) prevalence in a screening program. Radiologists (n=18) assessed the maximum antero-posterior abdominal aortic diameter by completing repeated caliper placements with the OTO, LTL, and ITI methods on 50 still abdominal aortic images obtained from an AAA screening program. Inter-observer reproducibility was calculated as the limit of agreement with the mean (LoA), which represents expected deviation of a single observer from the mean of all observers. Intra-observer reproducibility was assessed averaging the LoA for each observer with their repeated measurements. Based on data from an AAA screening trial and the estimated mean differences between the three principal methods, AAA prevalence was estimated using each of the methods. The inter-observer LoA of the OTO, ITI, and LTL was 2.6, 1.9, and 1.9 mm, whereas the intra-observer LoA was 2.0, 1.6, and 1.5 mm, respectively. Mean differences of 5.0 mm were found between OTO and ITI measurements, 2.6 mm between OTO and LTL measurements, and 2.4 mm between LTL and ITI measurements. The prevalence of AAA almost doubled using OTO instead of ITI, while the difference between ITI and LTL was minor (3.3% vs. 4.0% AAA). The study shows superior reproducibility of LTL and ITI compared with the OTO method of caliper placement in ultrasound determination of maximum abdominal aortic diameter, and the choice of caliper placement method significantly affects the prevalence of AAAs in screening programs

Lead isotope ratios in artists' lead white: a progress report

Energy Technology Data Exchange (ETDEWEB)

Keisch, B; Callahan, R C [Carnegie-Mellon Univ., Pittsburgh, Pa. (USA)

1976-07-01

The lead isotope ratios in over four hundred samples of lead white have been determined. The samples represent various geographical sources and dates from the thirteenth century to the present. A new method for organizing this large volume of data is described which helps with the visualization of temporal and geographic patterns. A number of interesting relationships between lead isotope ratio and date or source are shown to exist. Some examples of successful applications of this methodology are described.

Gap energy studied by optical transmittance in lead iodide monocrystals grown by Bridgman's Method

Directory of Open Access Journals (Sweden)

Veissid N.

1999-01-01

Full Text Available The bandgap energy as a function of temperature has been determined for lead iodide. The monocrystal was obtained in a vacuum sealed quartz ampoule inside a vertical furnace by Bridgman's method. The optical transmittance measurement enables to evaluate the values of Eg. By a fitting procedure of Eg as a function of temperature is possible to extract the parameters that govern its behavior. The variation of Eg with temperature was determined as: Eg(T = Eg(0 - aT2/(a + T, with: Eg(0 = (2.435 ± 0.008 eV, a = (8.7 ± 1.3 x 10-4 eV/K and a = (192 ± 90 K. The bandgap energy of lead iodide at room temperature was found to be 2.277 ± 0.007 eV.

Lead isotope ratios in artists' lead white: a progress report

International Nuclear Information System (INIS)

Keisch, B.; Callahan, R.C.

1976-01-01

The lead isotope ratios in over four hundred samples of lead white have been determined. The samples represent various geographical sources and dates from the thirteenth century to the present. A new method for organizing this large volume of data is described which helps with the visualization of temporal and geographic patterns. A number of interesting relationships between lead isotope ratio and date or source are shown to exist. Some examples of successful applications of this methodology are described. (author)

Specificities of reactor coolant pumps units with lead and lead-bismuth coolant

International Nuclear Information System (INIS)

Beznosov, A.V.; Anotonenkov, M.A.; Bokov, P.A.; Baranova, V.S.; Kustov, M.S.

2009-01-01

The analysis results of impact of lead and lead-bismuth coolants specific properties on the coolants flow features in flow channels of the main and auxiliary circulating pumps are presented. Impossibility of cavitation initiation in flow channels of vane pumps pumping lead and lead-bismuth coolants was demonstrated. The experimental research results of discontinuity of heavy liquid metal coolant column were presented and conditions of gas cavitation initiation in coolant flow were discussed. Invalidity of traditional calculation methods of water and sodium coolants circulation pumps calculations for lead and lead-bismuth coolants circulation pumps was substantiated [ru

Lead pollution: lead content in milk from cows fed on contaminated forages

Energy Technology Data Exchange (ETDEWEB)

Sapetti, C; Arduino, E; Durio, P

1973-01-01

Lead toxicity is reviewed, and the history of the lead poisoning is described. Much of the lead pollution in soil is due to automobile exhaust. Two milk cows were fed forage with added lead acetate. The 20 kg of lead corresponded to 50 ppm, a level that is often found in hays near major highways. The cows milk was then analyzed for lead content. During the first and second phase of administration of lead salts, the milk cows did not show any evident symptoms of intoxication. The lead in the milk did have a marked correlation with the administered lead. The lead doses did not last long enough for chronic symptoms to begin. The dosage of lead in milk, due to the facility of drawing samples and the relevant levels of response, could represent a valid method for diagnosing incipient chronic intoxications.

Lead user projects in practice

DEFF Research Database (Denmark)

Brem, Alexander; Gutstein, Adele

2018-01-01

Earlier research on the lead user method is focused on individual case studies and how the method was applied in a specific context. In this paper, we take a broader approach, analyzing a sample of 24 lead user projects, which included working with 188 lead users. These projects were analyzed....... Moreover, crowdsourcing contests and netnography proved to be of significant value for the need, trend, and lead user identification phases. This paper concludes by discussing theoretical and practical implications, the limitations of this study, and recommendations for future studies....

Kinetics of oil saponification by lead salts in ancient preparations of pharmaceutical lead plasters and painting lead mediums.

Science.gov (United States)

Cotte, M; Checroun, E; Susini, J; Dumas, P; Tchoreloff, P; Besnard, M; Walter, Ph

2006-12-15

Lead soaps can be found in archaeological cosmetics as well as in oil paintings, as product of interactions of lead salts with oil. In this context, a better understanding of the formation of lead soaps allows a follow-up of the historical evolution of preparation recipes and provides new insights into conservation conditions. First, ancient recipes of both pharmaceutical lead plasters and painting lead mediums, mixtures of oil and lead salts, were reconstructed. The ester saponification by lead salts is determined by the preparation parameters which were quantified by FT-IR spectrometry. In particular, ATR/FT-IR spectrometer was calibrated by the standard addition method to quantitatively follow the kinetics of this reaction. The influence of different parameters such as temperature, presence of water and choice of lead salts was assessed: the saponification is clearly accelerated by water and heating. This analysis provides chemical explanations to the historical evolution of cosmetic and painting preparation recipes.

Gas cooled leads

International Nuclear Information System (INIS)

Shutt, R.P.; Rehak, M.L.; Hornik, K.E.

1993-01-01

The intent of this paper is to cover as completely as possible and in sufficient detail the topics relevant to lead design. The first part identifies the problems associated with lead design, states the mathematical formulation, and shows the results of numerical and analytical solutions. The second part presents the results of a parametric study whose object is to determine the best choice for cooling method, material, and geometry. These findings axe applied in a third part to the design of high-current leads whose end temperatures are determined from the surrounding equipment. It is found that cooling method or improved heat transfer are not critical once good heat exchange is established. The range 5 5 but extends over a large of values. Mass flow needed to prevent thermal runaway varies linearly with current above a given threshold. Below that value, the mass flow is constant with current. Transient analysis shows no evidence of hysteresis. If cooling is interrupted, the mass flow needed to restore the lead to its initially cooled state grows exponentially with the time that the lead was left without cooling

What is lead-based paint?

International Nuclear Information System (INIS)

Vernon, L.S.

1994-01-01

The number of variety of lead-abatement regulations and requirements make it difficult and confusing to identify and properly respond to dangerous levels of lead in every situation. Definitions of ''lead-based paint'' and three test methods for lead detection are described to help determine when and how to test for the presence of lead

Childhood lead poisoning investigations: evaluating a portable instrument for testing soil lead.

Science.gov (United States)

Reames, Ginger; Lance, Larrie L

2002-04-01

The Childhood Lead Poisoning Prevention Branch of the California Department of Health Services evaluated a portable X-ray fluorescence (XRF) instrument for use as a soil lead-testing tool during environmental investigations of lead-poisoned children's homes. A Niton XRF was used to test soil at 119 sampling locations in the yards of 11 San Francisco Bay Area houses. Niton XRF readings were highly correlated with laboratory results and met the study criteria for an acceptable screening method. The data suggest that the most health-protective and time-efficient approach to testing for soil lead above regulatory levels is to take either surface readings or readings of a test cup of soil prepared by grinding with a mortar and pestle. The advantage of the test cup method is that the test cup with soil may be submitted to a laboratory for confirmatory analysis.

Study on residual discharge time of lead-acid battery based on fitting method

Science.gov (United States)

Liu, Bing; Yu, Wangwang; Jin, Yueqiang; Wang, Shuying

2017-05-01

This paper use the method of fitting to discuss the data of C problem of mathematical modeling in 2016, the residual discharge time model of lead-acid battery with 20A,30A,…,100A constant current discharge is obtained, and the discharge time model of discharge under arbitrary constant current is presented. The mean relative error of the model is calculated to be about 3%, which shows that the model has high accuracy. This model can provide a basis for optimizing the adaptation of power system to the electrical motor vehicle.

All roads lead to Rome - New search methods for the optimal triangulation problem

Czech Academy of Sciences Publication Activity Database

Ottosen, T. J.; Vomlel, Jiří

2012-01-01

Roč. 53, č. 9 (2012), s. 1350-1366 ISSN 0888-613X R&D Projects: GA MŠk 1M0572; GA ČR GEICC/08/E010; GA ČR GA201/09/1891 Grant - others:GA MŠk(CZ) 2C06019 Institutional support: RVO:67985556 Keywords : Bayesian networks * Optimal triangulation * Probabilistic inference * Cliques in a graph Subject RIV: BD - Theory of Information Impact factor: 1.729, year: 2012 http://library.utia.cas.cz/separaty/2012/MTR/vomlel-all roads lead to rome - new search methods for the optimal triangulation problem.pdf

“Lead Leached into Water from Select Plumbing Fixtures” Could Lead to Health Hazard

Directory of Open Access Journals (Sweden)

Ramsey Coles

2014-01-01

Full Text Available Background: Lead is an inert metal and is resistant to corrosion. It also increases tensile strength of many common materials in daily use. Lead was used during the Roman period to transport water (hence the name plumbing/plumber is common terminology even in the present day. Lead enters the biological system through the air, water, and dust. Fine particles of lead, having diameter less than 5 nm are directly absorbed by lungs. Inorganic lead is absorbed by the gastrointestinal tract, and organic lead is absorbed by the skin. Lead has long been known to be a toxic heavy metal and exposure is associated with many deleterious health effects. Still, lead remains a popular ingredient in products ranging from paint to batteries. The lead content in any given material is estimated using various methods. The least cumbersome method is found to be X-Ray Fluorescence technique (XRF. A portable XRF device was used in the present study. Aim: The main aim of this study to investigate whether lead is present in various commonly used plumbing materials. Material and Methods: All types of branded and commonly used pipes were gathered from a market in Bangalore and tested using the XRF machine. In order to evaluate to what extent lead from the pipes could leach into water, seven pipes were randomly selected and filled with Aquafina water (having undetectable level of lead for a 24 hour period. This water was tested at an NABL accredited laboratory in Bangalore, India for lead content. Result: It was determined that lead was present in many of the samples, at an unacceptable levels ranging from, well above the globally accepted level of 0.01 mg/L proof that lead was able to leach from the samples into water. Conclusions: As lead in drinking water represents a direct pathway for human exposure, the authors recommend that significant measures be taken to prevent use of lead in the plumbing industry for prevention of it’s deleterious effects. Authors have also

Application of risk analysis and quality control methods for improvement of lead molding process

Directory of Open Access Journals (Sweden)

H. Gołaś

2016-10-01

Full Text Available The aim of the paper is to highlight the significance of implication of risk analysis and quality control methods for the improvement of parameters of lead molding process. For this reason, Fault Mode and Effect Analysis (FMEA was developed in the conceptual stage of a new product TC-G100-NR. However, the final product was faulty (a complete lack of adhesion of brass insert to leak regardless of the previously defined potential problem and its preventive action. It contributed to the recognition of root causes, corrective actions and change of production parameters. It showed how these methods, level of their organization, systematic and rigorous study affect molding process parameters.

Lead Poison Detection

Science.gov (United States)

1976-01-01

With NASA contracts, Whittaker Corporations Space Science division has developed an electro-optical instrument to mass screen for lead poisoning. Device is portable and detects protoporphyrin in whole blood. Free corpuscular porphyrins occur as an early effect of lead ingestion. Also detects lead in urine used to confirm blood tests. Test is inexpensive and can be applied by relatively unskilled personnel. Similar Whittaker fluorometry device called "drug screen" can measure morphine and quinine in urine much faster and cheaper than other methods.

A method of lines solution of the transient behavior of the helium cooled power leads for the SSC

International Nuclear Information System (INIS)

Demko, J.A.; Schiesser, W.E.; Carcagno, R.; McAshan, M.

1995-01-01

In this study, a detailed numerical thermal mode of a 6.5 kA power lead for the Superconducting Super Collider has been developed, which was adapted from the dynamic model developed by Schiesser. The transient behavior of the power leads was modeled using, a method of lines (MOL) approach. The model was developed to pmvide a tool for analyzing coolant control strategies as well as an understanding of the behavior of the leads under presumed system transients. Results for a current ramp up to 4970 amps are favorably compared with measurements. Also, a loss of cooling situation is predicted to determine the transient temperature distribution under an off-design condition

A study on lead equivalent

International Nuclear Information System (INIS)

Lin Guanxin

1991-01-01

A study on the rules in which the lead equivalent of lead glass changes with the energy of X rays or γ ray is described. The reason of this change is discussed and a new testing method of lead equivalent is suggested

Comparison of methods for certification of stannic, stibium and lead traces in reference materials for steel

Directory of Open Access Journals (Sweden)

I. V. Khodakovskaya

2016-01-01

Full Text Available Development and introduction of new metallurgical technologies, new additional chemical compound indexes controlled in metallurgical materials demand to develop the new, more advanced methods of analytical control. The particular attention should be paid to identify the traces of stannic, stinium and lead because of their influence on metal characteristics.

Lead isotope in mineral exploration

International Nuclear Information System (INIS)

Gulson, B.L.

1986-01-01

This book provides an up-to-date state-of-the-art review of lead isotopes in mineral exploration. Beginning with an historical review on suggested uses of lead isotopes in mineral exploration, the author then outlines the theoretical aspects of lead isotopes and illustrates that the method is based on well-known principles of radioactive decay, from which isotopic signatures for different styles of mineralization are derived. The varying isotopic signatures are then introduced. The major part of the book details over 40 case histories for base and precious metals, uranium and tin using sampling media such as sulfides, gossans, soils, weathered bedrock, vegetation and groundwaters. Advantages and disadvantages of each are discussed. Examples are given of the use of lead isotopes in testing conceptual models for exploration. The success rate and cost-effectiveness of the method are illustrated by actual exploration examples. Analytical advances which should lower the cost of the method and future uses are outlined. Many of the case histories use recently published or unpublished data, 27 tables of which are given in an appendix. Details of sampling, the methods for obtaining the isotope ratios, and a commercially-available integrated lead isotope service are also provided. (Auth.)

Analysis of Traffic Accidents Leading to Death Using Tripod Beta Method in Yazd, Iran

Directory of Open Access Journals (Sweden)

Mehrzad Ebrahemzadih

2016-06-01

Full Text Available This study tried to find the original causes of road accidents to prevent their occurrence. This was a descriptive-analytic retrospective study which assessed 1,000 cases of road accidents leading to death during 2003-2013 using the Tripod Beta method. The latent problems, the contributing preconditions, and corrective strategies for the prevention of occurrence of these accidents were determined. The findings of this study revealed that violation of traffic safety rules, especially deliberate violations and risk-takings decreased with increasing age. In comparative status of the superficial problems, illegal and impermissible speed of drivers accounted for 19.10%, in comparative status of preconditions, violation of safety rules accounted for 32.6% and finally, in comparative status of the latent problems, the presence of financial constraints and time pressure in designing and manufacturing of the cars, and quality of city streets, roads, accounted for 20.1%, of the leading causes of occurrence of accidents in this study.

Large-capacity current leads

International Nuclear Information System (INIS)

Ballarino, A.

2008-01-01

Feeding superconducting magnets with reliable low-loss devices is a key issue for any cryo-electrical system. Conventional or HTS current leads can be used, and cooling methods, materials, and geometries can be chosen to optimize the thermo-electrical performance of the system. The LHC magnets are powered via more than 3000 current leads transporting altogether about 3 MA of current. With thousands of leads, the LHC lead project represents today the largest project of its kind ever undertaken. Following a review of the LHC lead project, an overview of the choices that can be made for the optimization of large capacity current leads is presented. Examples are given of other leads for large scale magnet systems for which the use of HTS is being envisaged

Performance of Lead-Free versus Lead-Based Hunting Ammunition in Ballistic Soap

Science.gov (United States)

Gremse, Felix; Krone, Oliver; Thamm, Mirko; Kiessling, Fabian; Tolba, René Hany; Rieger, Siegfried; Gremse, Carl

2014-01-01

Background Lead-free hunting bullets are an alternative to lead-containing bullets which cause health risks for humans and endangered scavenging raptors through lead ingestion. However, doubts concerning the effectiveness of lead-free hunting bullets hinder the wide-spread acceptance in the hunting and wildlife management community. Methods We performed terminal ballistic experiments under standardized conditions with ballistic soap as surrogate for game animal tissue to characterize dimensionally stable, partially fragmenting, and deforming lead-free bullets and one commonly used lead-containing bullet. The permanent cavities created in soap blocks are used as a measure for the potential wound damage. The soap blocks were imaged using computed tomography to assess the volume and shape of the cavity and the number of fragments. Shots were performed at different impact speeds, covering a realistic shooting range. Using 3D image segmentation, cavity volume, metal fragment count, deflection angle, and depth of maximum damage were determined. Shots were repeated to investigate the reproducibility of ballistic soap experiments. Results All bullets showed an increasing cavity volume with increasing deposited energy. The dimensionally stable and fragmenting lead-free bullets achieved a constant conversion ratio while the deforming copper and lead-containing bullets showed a ratio, which increases linearly with the total deposited energy. The lead-containing bullet created hundreds of fragments and significantly more fragments than the lead-free bullets. The deflection angle was significantly higher for the dimensionally stable bullet due to its tumbling behavior and was similarly low for the other bullets. The deforming bullets achieved higher reproducibility than the fragmenting and dimensionally stable bullets. Conclusion The deforming lead-free bullet closely resembled the deforming lead-containing bullet in terms of energy conversion, deflection angle, cavity shape

Performance of lead-free versus lead-based hunting ammunition in ballistic soap.

Directory of Open Access Journals (Sweden)

Felix Gremse

Full Text Available BACKGROUND: Lead-free hunting bullets are an alternative to lead-containing bullets which cause health risks for humans and endangered scavenging raptors through lead ingestion. However, doubts concerning the effectiveness of lead-free hunting bullets hinder the wide-spread acceptance in the hunting and wildlife management community. METHODS: We performed terminal ballistic experiments under standardized conditions with ballistic soap as surrogate for game animal tissue to characterize dimensionally stable, partially fragmenting, and deforming lead-free bullets and one commonly used lead-containing bullet. The permanent cavities created in soap blocks are used as a measure for the potential wound damage. The soap blocks were imaged using computed tomography to assess the volume and shape of the cavity and the number of fragments. Shots were performed at different impact speeds, covering a realistic shooting range. Using 3D image segmentation, cavity volume, metal fragment count, deflection angle, and depth of maximum damage were determined. Shots were repeated to investigate the reproducibility of ballistic soap experiments. RESULTS: All bullets showed an increasing cavity volume with increasing deposited energy. The dimensionally stable and fragmenting lead-free bullets achieved a constant conversion ratio while the deforming copper and lead-containing bullets showed a ratio, which increases linearly with the total deposited energy. The lead-containing bullet created hundreds of fragments and significantly more fragments than the lead-free bullets. The deflection angle was significantly higher for the dimensionally stable bullet due to its tumbling behavior and was similarly low for the other bullets. The deforming bullets achieved higher reproducibility than the fragmenting and dimensionally stable bullets. CONCLUSION: The deforming lead-free bullet closely resembled the deforming lead-containing bullet in terms of energy conversion

Nanosized lead lanthanum titanate (PLT) ceramic powders synthesized by the oxidant peroxo method

Energy Technology Data Exchange (ETDEWEB)

Camargo, Emerson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil)], E-mail: camargo@ufscar.br; Barrado, Cristiano M. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil); Ribeiro, Caue [EMBRAPA Instrumentacao Agropecuaria, Rua XV de Novembro 1452, Sao Carlos SP 13560-970 (Brazil)], E-mail: caue@cnpdia.embrapa.br; Longo, Elson [Department of Biochemistry, Chemistry Institute of Araraquara, UNESP-Sao Paulo State University, Rua Francisco Degni, CP 355, Araraquara SP 14801-907 (Brazil)], E-mail: elson@iq.unesp.br; Leite, Edson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil)], E-mail: derl@power.ufscar.br

2009-05-05

For the first time it is reported the synthesis of lead titanate modified with rare earth by the oxidant-peroxo method (OPM). Lanthanum was added up to 20% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of a solution of lead and lanthanum nitrate into an aqueous solution of titanium peroxo complexes. The amorphous precipitate formed was heat-treated at different temperatures in the range from 400 to 900 deg. C for crystallization. Powders were characterized by Raman spectroscopy and X-ray diffraction. Tetragonal perovskite structure was observed for the samples up to 15% of lanthanum substitution and cubic perovskite for sample with 20% of lanthanum. Crystallographic domains calculated by Scherrer equation showing a probable suppression of the crystallite growth in function of lanthanum content. It was observed shifting to lower frequencies of Raman modes in the range between 100 and 400 cm{sup -1} and the vanishing of the A1(2TO) and E(1LO) modes could be attributed to transition phase from tetragonal to cubic. Electronic microscopy image revealed that the powders annealed at height temperature are spherical with sharp size distribution.

Nanosized lead lanthanum titanate (PLT) ceramic powders synthesized by the oxidant peroxo method

International Nuclear Information System (INIS)

Camargo, Emerson R.; Barrado, Cristiano M.; Ribeiro, Caue; Longo, Elson; Leite, Edson R.

2009-01-01

For the first time it is reported the synthesis of lead titanate modified with rare earth by the oxidant-peroxo method (OPM). Lanthanum was added up to 20% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of a solution of lead and lanthanum nitrate into an aqueous solution of titanium peroxo complexes. The amorphous precipitate formed was heat-treated at different temperatures in the range from 400 to 900 deg. C for crystallization. Powders were characterized by Raman spectroscopy and X-ray diffraction. Tetragonal perovskite structure was observed for the samples up to 15% of lanthanum substitution and cubic perovskite for sample with 20% of lanthanum. Crystallographic domains calculated by Scherrer equation showing a probable suppression of the crystallite growth in function of lanthanum content. It was observed shifting to lower frequencies of Raman modes in the range between 100 and 400 cm -1 and the vanishing of the A1(2TO) and E(1LO) modes could be attributed to transition phase from tetragonal to cubic. Electronic microscopy image revealed that the powders annealed at height temperature are spherical with sharp size distribution.

Leading healthcare in complexity.

Science.gov (United States)

Cohn, Jeffrey

2014-12-01

Healthcare institutions and providers are in complexity. Networks of interconnections from relationships and technology create conditions in which interdependencies and non-linear dynamics lead to surprising, unpredictable outcomes. Previous effective approaches to leadership, focusing on top-down bureaucratic methods, are no longer effective. Leading in complexity requires leaders to accept the complexity, create an adaptive space in which innovation and creativity can flourish and then integrate the successful practices that emerge into the formal organizational structure. Several methods for doing adaptive space work will be discussed. Readers will be able to contrast traditional leadership approaches with leading in complexity. They will learn new behaviours that are required of complexity leaders, along with challenges they will face, often from other leaders within the organization.

Isolation of radioactive thallium from lead targets

International Nuclear Information System (INIS)

Kozlova, M.D.; Sevast'yanova, A.S.; Malinin, A.B.; Kurenkov, N.V.

1989-01-01

Two methods of thallium-201 preperation from Pb-targets irradiated with protons: precipitation-extraction (1) and extraction (2) - are developed. When the target irraiated is extracted during the time necessary for bismuth-201 transformation into lead-201, lead macroquantity containing lead-201 was separated from undesirable thallium radionuclides, which are formed in direct nuclear reactions. The lead fraction was extracted to accumulate thallium-201, and it was separated from lead mocroquantity. The target was dissolved in the nitric acid. The 1st method differs from the 2nd one by the fact that before thallium-201 extraction, lead was precipitaed by the nitric acid. The 1st method permits to separate thallium-201 with chemical yield not less than 90 %, the 2nd one - ≥95 %. 2 refs

Comparison of two methods for blood lead analysis in cattle: graphite-furnace atomic absorption spectrometry and LeadCare(R) II system.

Science.gov (United States)

Bischoff, Karyn; Gaskill, Cynthia; Erb, Hollis N; Ebel, Joseph G; Hillebrandt, Joseph

2010-09-01

The current study compared the LeadCare(R) II test kit system with graphite-furnace atomic absorption spectrometry for blood lead (Pb) analysis in 56 cattle accidentally exposed to Pb in the field. Blood Pb concentrations were determined by LeadCare II within 4 hr of collection and after 72 hr of refrigeration. Blood Pb concentrations were determined by atomic absorption spectrometry, and samples that were coagulated (n = 12) were homogenized before analysis. There was strong rank correlation (R(2) = 0.96) between atomic absorption and LeadCare II (within 4 hr of collection), and a conversion formula was determined for values within the observed range (3-91 mcg/dl, although few had values >40 mcg/dl). Median and mean blood pb concentrations for atomic absorption were 7.7 and 15.9 mcg/dl, respectively; for LeadCare II, medians were 5.2 mcg/dl at 4 hr and 4.9 mcg/dl at 72 hr, and means were 12.4 and 11.7, respectively. LeadCare II results at 4 hr strongly correlated with 72 hr results (R(2) = 0.96), but results at 72 hr were lower (P atomic absorption. Although there have been several articles that compared LeadCare with other analytical techniques, all were for the original system, not LeadCare II. The present study indicated that LeadCare II results correlated well with atomic absorption over a wide range of blood Pb concentrations and that refrigerating samples for up to 72 hr before LeadCare II analysis was acceptable for clinical purposes.

Lead isotopic compositions of environmental certified reference materials for an inter-laboratory comparison of lead isotope analysis

International Nuclear Information System (INIS)

Aung, Nyein Nyein; Uryu, Tsutomu; Yoshinaga, Jun

2004-01-01

Lead isotope ratios, viz. 207 Pb/ 206 Pb and 208 Pb/ 206 Pb, of the commercially available certified reference materials (CRMs) issued in Japan are presented with an objective to provide a data set, which will be useful for the quality assurance of analytical procedures, instrumental performance and method validation of the laboratories involved in environmental lead isotope ratio analysis. The analytical method used in the present study was inductively coupled plasma quadrupole mass spectrometry (ICPQMS) presented by acid digestion and with/without chemical separation of lead from the matrix. The precision of the measurements in terms of the relative standard deviation (RSD) of triplicated analyses was 0.19% and 0.14%, for 207 Pb/ 206 Pb and 208 Pb/ 206 Pb, respectively. The trueness of lead isotope ratio measurements of the present study was tested with a few CRMs, which have been analyzed by other analytical methods and reported in various literature. The lead isotopic ratios of 18 environmental matrix CRMs (including 6 CRMs analyzed for our method validation) are presented and the distribution of their ratios is briefly discussed. (author)

Lead exposures from varnished floor refinishing.

Science.gov (United States)

Schirmer, Joseph; Havlena, Jeff; Jacobs, David E; Dixon, Sherry; Ikens, Robert

2012-01-01

We evaluated the presence of lead in varnish and factors predicting lead exposure from floor refinishing and inexpensive dust suppression control methods. Lead in varnish, settled dust, and air were measured using XRF, laboratory analysis of scrape and wipe samples, and National Institute for Occupational Safety and Health (NIOSH) Method 7300, respectively, during refinishing (n = 35 homes). Data were analyzed using step-wise logistic regression. Compared with federal standards, no lead in varnish samples exceeded 1.0 mg/cm(2), but 52% exceeded 5000 ppm and 70% of settled dust samples after refinishing exceeded 40 μg/ft(2). Refinishing pre-1930 dwellings or stairs predicted high lead dust on floors. Laboratory analysis of lead in varnish was significantly correlated with airborne lead (r = 0.23, p = 0.014). Adding dust collection bags into drum sanders and HEPA vacuums to edgers and buffers reduced mean floor lead dust by 8293 μg Pb/ft(2) (pairborne lead exposures to less than 50 μg/m(3). Refinishing varnished surfaces in older housing produces high but controllable lead exposures.

Quantum confinement of lead titanate nanocrystals by wet chemical method

Energy Technology Data Exchange (ETDEWEB)

Kaviyarasu, K., E-mail: kaviyarasuloyolacollege@gmail.com [UNESCO-UNISA Africa Chair in Nanosciences/Nanotechnology Laboratories, College of Graduate Studies, University of South Africa (UNISA), Muckleneuk Ridge, P O Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), Materials Research Department (MSD), iThemba LABS-National Research Foundation - NRF, 1 Old Faure Road, 7129, P O Box 722, Somerset West, Western Cape Province (South Africa); Manikandan, E., E-mail: maniphysics@gmail.com [Nanosciences African Network (NANOAFNET), Materials Research Department (MSD), iThemba LABS-National Research Foundation - NRF, 1 Old Faure Road, 7129, P O Box 722, Somerset West, Western Cape Province (South Africa); Central Research Laboratory, Sree Balaji Medical College & Hospital, Bharath University, Chrompet, Chennai, Tamil Nadu (India); Nuru, Z.Y. [UNESCO-UNISA Africa Chair in Nanosciences/Nanotechnology Laboratories, College of Graduate Studies, University of South Africa (UNISA), Muckleneuk Ridge, P O Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), Materials Research Department (MSD), iThemba LABS-National Research Foundation - NRF, 1 Old Faure Road, 7129, P O Box 722, Somerset West, Western Cape Province (South Africa); Maaza, M., E-mail: likmaaz@gmail.com [UNESCO-UNISA Africa Chair in Nanosciences/Nanotechnology Laboratories, College of Graduate Studies, University of South Africa (UNISA), Muckleneuk Ridge, P O Box 392, Pretoria (South Africa); Nanosciences African Network (NANOAFNET), Materials Research Department (MSD), iThemba LABS-National Research Foundation - NRF, 1 Old Faure Road, 7129, P O Box 722, Somerset West, Western Cape Province (South Africa)

2015-11-15

Lead Titanate (PbTiO{sub 3)} is a category of the practical semiconductor metal oxides, which is widely applied in various scientific and industrial fields because of its catalytic, optical, and electrical properties. PbTiO{sub 3} nanocrystalline materials have attracted a wide attention due to their unique properties. PbTiO{sub 3} nanocrystals were investigated by X-ray diffraction (XRD) to identify the PbTiO{sub 3} nanocrystals were composed a tetragonal structure. The diameter of a single sphere was around 20 nm and the diameter reached up to 3 μm. The chemical composition of the samples and the valence states of elements were determined by X-ray photoelectron spectroscopy (XPS) in detail. - Highlights: • Single crystalline NSs of PbTiO{sub 3} fabricated by wet chemical method. • PbTiO{sub 3} NSs were uniform and continuous along the long axis. • Tetragonal perovskite structure with the diameter 20 nm and length 3 μm. • XPS spectrum was fitted with Lorentzian function respectively. • The size of the images is also 10 μm × 10 μm.

Secondary lead production

Energy Technology Data Exchange (ETDEWEB)

Hollis, R.G.

1990-10-16

This invention is concerned with the efficient recovery of soft lead from the paste component of used automobile lead-acid storage batteries. According to the invention, a scrap which contains lead oxide, lead sulfate, and antimony in an oxidized state is processed in the following steps to recover lead. A refractory lined reaction vessel is continuously charged with the scrap, along with a reductant effective for reducing lead oxide. The charged material is melted and agitated by means of a submerged lance at 900-1150{degree}C whereby some of the lead oxide of the scrap is reduced to form molten lead. A slag layer is then formed above the molten lead, and an amount of lead oxide is maintained in the slag layer. The molten lead, now containing under 0.5 wt % of antimony, is removed, and the antimony oxide in the scrap is concentrated as oxide in the slag layer. Preferred embodiments of the invention result in the production, in a single step, of a soft lead substantially free of antimony. The slag may be subsequently treated to reduce the antimony oxide and produce a valuable antimony-lead product. Further advantages of the process are that a wet battery paste may be used as the feed without prior drying, and the process can be conducted at a temperature 100-150{degree}C lower than in previously known methods. In addition, a smaller reactor can be employed which reduces both capital cost and fuel costs. The process of the invention is illustrated by descriptions of pilot plant tests. 1 fig.

Lead: Aspects of its ecology and environmental toxicity. [physiological effects of lead compound contamination of environment

Science.gov (United States)

Siegel, S. M.

1973-01-01

An analysis of lead toxicity in the Hawaiian environment was conducted. It was determined that lead enters the environment as an industrial contaminant resulting from the combustion of leaded gasoline. The amount of lead absorbed by the plants in various parts of the Hawaiian Islands is reported. The disposition of lead in the sediments of canals and yacht basins was investigated. The methods for conducting the surveys of lead content are described. Possible consequences of continued environmental pollution by burning leaded gasoline are discussed.

Synthesis and characterization of lead zirconate titanate powders obtained by the oxidant peroxo method

International Nuclear Information System (INIS)

Camargo, Emerson R.; Leite, Edson R.; Longo, Elson

2009-01-01

Lead zirconate titanate (PbZr 1-x Ti x O 3 ) was synthesized by the 'oxidant peroxo method (OPM)' with 'x' between 0.25 and 0.50. Titanium metal was dissolved into a hydrogen peroxide/ammonia aqueous solution, followed by the addition of lead and zirconium nitrate solution. The amorphous precipitated precursor obtained was crystallized by heat treatment between 400 and 1000 deg. C. Images of transmission microscopy showed spherical particles with average diameter between 20 and 60 nm, and the presence of necks between particles treated at 700 deg. C. All of the unpressed powders were characterized by X-ray diffractometry and FT-Raman spectroscopy. Powder samples with 'x' up to 0.35 showed rhombohedral structure when treated at temperatures higher than 500 deg. C, and tetragonal structure when 'x' was higher than 0.40. Analysis of XRD and Raman spectroscopy of the precursor powders showed amorphous-like structures, however powders treated at 400 deg. C showed a structure identified as an intermediate pyrochlore phase, independently of the Zr and Ti mole ratio

Lead distribution in soils impacted by a secondary lead smelter: Experimental and modelling approaches

Energy Technology Data Exchange (ETDEWEB)

Schneider, Arnaud R., E-mail: arnaud.schneider@univ-reims.fr [GEGENAA, EA 3795, Université de Reims Champagne-Ardenne, SFR Condorcet FR CNRS 3417, 2 esplanade Roland Garros, 51100 Reims (France); Cancès, Benjamin; Ponthieu, Marie [GEGENAA, EA 3795, Université de Reims Champagne-Ardenne, SFR Condorcet FR CNRS 3417, 2 esplanade Roland Garros, 51100 Reims (France); Sobanska, Sophie [Laboratoire de Spectrochimie IR et Raman, UMR-CNRS 8516, Bât. C5 Université de Lille I, 59655 Villeneuve d' Ascq Cedex (France); Benedetti, Marc F. [Institut de Physique du Globe de Paris, Sorbonne Paris Cité, Université Paris Diderot, UMR 7154, CNRS, F-75005 Paris (France); Pourret, Olivier [HydrISE, Institut Polytechnique LaSalle Beauvais, FR-60000 Beauvais (France); Conreux, Alexandra; Calandra, Ivan; Martinet, Blandine; Morvan, Xavier; Gommeaux, Maxime; Marin, Béatrice [GEGENAA, EA 3795, Université de Reims Champagne-Ardenne, SFR Condorcet FR CNRS 3417, 2 esplanade Roland Garros, 51100 Reims (France)

2016-10-15

Smelting activities are one of the most common sources of trace elements in the environment. The aim of this study was to determine the lead distribution in upper horizons (0–5 and 5–10 cm) of acidic soils in the vicinity of a lead-acid battery recycling plant in northern France. The combination of chemical methods (sequential extractions), physical methods (Raman microspectroscopy and scanning electron microscopy with an energy dispersive spectrometer) and multi-surface complexation modelling enabled an assessment of the behaviour of Pb. Regardless of the studied soil, none of the Pb-bearing phases commonly identified in similarly polluted environments (e.g., anglesite) were observed. Lead was mainly associated with organic matter and manganese oxides. The association of Pb with these soil constituents can be interpreted as evidence of Pb redistribution in the studied soils following smelter particle deposition. - Highlights: • Lead behavior was studied in smelter impacted soils. • A combination of experimental methods and modelling was employed. • Pb was mainly associated with organic matter and to a lesser degree with Mn oxides. • Pb was redistributed in soils after smelter particle deposition.

Lead distribution in soils impacted by a secondary lead smelter: Experimental and modelling approaches

International Nuclear Information System (INIS)

Schneider, Arnaud R.; Cancès, Benjamin; Ponthieu, Marie; Sobanska, Sophie; Benedetti, Marc F.; Pourret, Olivier; Conreux, Alexandra; Calandra, Ivan; Martinet, Blandine; Morvan, Xavier; Gommeaux, Maxime; Marin, Béatrice

2016-01-01

Smelting activities are one of the most common sources of trace elements in the environment. The aim of this study was to determine the lead distribution in upper horizons (0–5 and 5–10 cm) of acidic soils in the vicinity of a lead-acid battery recycling plant in northern France. The combination of chemical methods (sequential extractions), physical methods (Raman microspectroscopy and scanning electron microscopy with an energy dispersive spectrometer) and multi-surface complexation modelling enabled an assessment of the behaviour of Pb. Regardless of the studied soil, none of the Pb-bearing phases commonly identified in similarly polluted environments (e.g., anglesite) were observed. Lead was mainly associated with organic matter and manganese oxides. The association of Pb with these soil constituents can be interpreted as evidence of Pb redistribution in the studied soils following smelter particle deposition. - Highlights: • Lead behavior was studied in smelter impacted soils. • A combination of experimental methods and modelling was employed. • Pb was mainly associated with organic matter and to a lesser degree with Mn oxides. • Pb was redistributed in soils after smelter particle deposition.

From virtuality to reality - Virtual screening in lead discovery and lead optimization: a medicinal chemistry perspective.

Science.gov (United States)

Rester, Ulrich

2008-07-01

Drug discovery and development is an interdisciplinary, expensive and time-consuming process. Scientific advancements during the past two decades have altered the way pharmaceutical research produces novel bio-active molecules. Advances in computational techniques and hardware solutions have enabled in silico methods, and in particular virtual screening, to speed up modern lead identification and lead optimization. Recent successes have proven the power of combining virtual screening with complementary and synergistic biophysical methods, such as X-ray crystallography, NMR spectroscopy and isothermal titration calorimetry (ITC). This review addresses key issues, challenges and recent improvements of virtual screening methods and strategies. Examples highlighting the impact of an integrated virtual screening and biophysical characterization platform in the lead identification and optimization process are presented and discussed.

Environmental lead exposure among preschool children in Shanghai, China: blood lead levels and risk factors.

Directory of Open Access Journals (Sweden)

Jia Cao

Full Text Available OBJECTIVE: To determine blood lead levels and to identify related risk factors among children in Shanghai; to explore the lead change trend of children after industrial transformation and to provide data for policy development to control environmental lead pollution in Shanghai. METHODS: A stratified-clustered-random sampling method was used. A tungsten atomizer absorption spectrophotometer was employed to determine blood lead levels. RESULTS: The arithmetic mean, geometric mean and median of blood lead levels of 0- to 6-year-old children from Shanghai were 22.49 µg/L, 19.65 µg/L and 19.5 µg/L, including 0.26% (6/2291 with concentrations ≥100 µg/L and 2.7% (61/2291 with concentrations ≥50 µg/L. Boys' levels (23.57 µg/L were greater than those of girls (21.2 µg/L. The blood lead levels increased with age. This survey showed that the Chongming district was the highest and Yangpu district was the lowest, this result is completely opposite with the earlier survey in Shanghai. Risk factors for lead contamination included housing environment, parents' education levels, social status, hobbies, and children's nutritional status. CONCLUSIONS: The blood lead levels of children in Shanghai were lower than the earlier data of Shanghai and those of published studies in China, but higher than the blood lead levels of developed countries. The blood lead levels of urban districts are higher than the central districts with the industrial transformation. Society and the government should take an active interest in childhood lead poisoning of urban areas.

Method and System for Weakening Shock Wave Strength at Leading Edge Surfaces of Vehicle in Supersonic Atmospheric Flight

Science.gov (United States)

Daso, Endwell O. (Inventor); Pritchett, Victor E., II (Inventor); Wang, Ten-See (Inventor); Farr, Rebecca Ann (Inventor); Auslender, Aaron Howard (Inventor); Blankson, Isaiah M. (Inventor); Plotkin, Kenneth J. (Inventor)

2015-01-01

A method and system are provided to weaken shock wave strength at leading edge surfaces of a vehicle in atmospheric flight. One or more flight-related attribute sensed along a vehicle's outer mold line are used to control the injection of a non-heated, non-plasma-producing gas into a local external flowfield of the vehicle from at least one leading-edge surface location along the vehicle's outer mold line. Pressure and/or mass flow rate of the gas so-injected is adjusted in order to cause a Rankine-Hugoniot Jump Condition along the vehicle's outer mold line to be violated.

Technology-based vs. traditional instruction. A comparison of two methods for teaching the skill of performing a 12-lead ECG.

Science.gov (United States)

Jeffries, Pamela R; Woolf, Shirley; Linde, Beverly

2003-01-01

The purpose of this study was to compare the effectiveness of an interactive, multimedia CD-ROM with traditional methods of teaching the skill of performing a 12-lead ECG. A randomized pre/posttest experimental design was used. Seventy-seven baccalaureate nursing students in a required, senior-level critical-care course at a large midwestern university were recruited for the study. Two teaching methods were compared. The traditional method included a self-study module, a brief lecture and demonstration by an instructor, and hands-on experience using a plastic manikin and a real 12-lead ECG machine in the learning laboratory. The second method covered the same content using an interactive, multimedia CD-ROM embedded with virtual reality and supplemented with a self-study module. There were no significant (p method, or perception of self-efficacy in performing the skill. Overall results indicated that both groups were satisfied with their instructional method and were similar in their ability to demonstrate the skill correctly on a live, simulated patient. This evaluation study is a beginning step to assess new and potentially more cost-effective teaching methods and their effects on student learning outcomes and behaviors, including the transfer of skill acquisition via a computer simulation to a real patient.

Lead-elevated activity of xanthine oxidase in lead-exposed workers

Directory of Open Access Journals (Sweden)

Sławomir Kasperczyk

2013-04-01

Full Text Available Background: The aim of the present study was to explore the connection between lead toxicity and the activity of xanthine oxidase (XO. In addition, we indicated the uric acid (UA and creatinine levels and concentration of erythrocyte malondialdehyde (MDA to estimate oxidative stress intensity. Materials and Methods: The examined group consisted of 125 healthy male employees of zinc and lead works. The examined group was divided into tertiles according to blood lead levels. In the collected blood samples, concentrations of lead-exposure indices, UA, creatinine, and MDA as well as activity of XO were measured concomitantly. The control group consisted of 32 healthy male administrative workers who were exposed to lead only environmentally. Results: XO activity and MDA level were significantly elevated in all tertiles compared to the control group. Creatinine level was significantly elevated in the medium and high tertiles. However, the level of UA was significantly elevated in the high tertile, while in the low and medium tertile only a tendency toward higher values was observed. Conclusions: Occupational exposure to lead induces activity of XO. This induction may contribute to the observed simultaneously increased oxidative stress, measured as MDA level, and the increased level of UA. Med Pr 2013;64(2:175–180

Two-step extraction method for lead isotope fractionation to reveal anthropogenic lead pollution.

Science.gov (United States)

Katahira, Kenshi; Moriwaki, Hiroshi; Kamura, Kazuo; Yamazaki, Hideo

2018-05-28

This study developed the 2-step extraction method which eluted the Pb adsorbing on the surface of sediments in the first solution by aqua regia and extracted the Pb absorbed inside particles into the second solution by mixed acid of nitric acid, hydrofluoric acid and hydrogen peroxide solution. We applied the method to sediments in the enclosed water area and found out that the isotope ratios of Pb in the second solution represented those of natural origin. This advantage of the method makes it possible to distinguish the Pb between natural origin and anthropogenic source on the basis of the isotope ratios. The results showed that the method was useful to discuss the Pb sources and that anthropogenic Pb in the sediment samples analysed was mainly derived from China because of transboundary air pollution.

INAA, AAS, and lead isotope analysis of ancient lead anchors from the black SEA

International Nuclear Information System (INIS)

Kuleff, I.; Djingova, R.; Alexandrova, A.

1995-01-01

Lead stock of wooden-lead anchors found along the Bulgarian Black Sea coast and typo logically dated VI c. B.C. - III c. A.D. have been analyzed for chemical composition and lead isotope ratios by INAA, AAS and mass spectrometry. Using multivariate methods for analysis as well as simple bi variate plots the lead for production of the stocks was localized as originating from Laurion, Thassos, Troas, Chalkidike and the Rhodopes. In general, the chemical composition is not recommended to be used for provenance study of lead artefacts. Combining the results from this study with the existing typo logical classification certain conclusion about the production and distribution of lead anchors in the Aegean region are made. (author). 22 refs., 3 figs., 4 tabs

A rugged and transferable method for determining blood cadmium, mercury, and lead with inductively coupled plasma-mass spectrometry

International Nuclear Information System (INIS)

McShane, William J.; Pappas, R. Steven; Wilson-McElprang, Veronica; Paschal, Dan

2008-01-01

A simple, high-throughput method for determining total cadmium, mercury, and lead in blood in cases of suspected exposure, using inductively coupled plasma-mass spectrometry (ICP-MS), has been developed and validated. One part matrix-matched standards, blanks, or aliquots of blood specimens were diluted with 49 parts of a solution containing 0.25% (w/w) tetramethylammonium hydroxide; 0.05% v/v Triton X-100 (blood cell membranes and protein solubilization); 0.01% (w/v) ammonium pyrolidinedithiocarbamate (mercury memory effect prevention and oxidation state stabilization, solubilization by complexation of all three metals); 1% v/v isopropanol (signal enhancement); and 10 μg/L iridium (internal standard). Thus the final dilution factor is 1 + 49. The method provides the basis for the determination of total cadmium, mercury, and lead for assessment of environmental, occupational, accidental ingestion or elevated exposures from other means. Approximately 80 specimens, including blanks, calibration standards, and quality control materials can be processed in an 8-h day. The method has been evaluated by examining reference materials from the National Institute of Standards and Technology, as well as by participation in six rounds of proficiency testing intercomparisons led by the Wadsworth Center of the New York State Department of Health. This method was developed for the purpose of increasing U.S. emergency response laboratory capacity. To this end, 33 U.S. state, and 1 district health department laboratories have validated this method in their own laboratories

A rugged and transferable method for determining blood cadmium, mercury, and lead with inductively coupled plasma-mass spectrometry

Energy Technology Data Exchange (ETDEWEB)

McShane, William J. [Battelle-Centers for Disease Control and Prevention, Division of Laboratory Sciences, Emergency Response and Air Toxicants Branch, 4770 Buford Highway, MS F-44, Atlanta, GA 30341 (United States)], E-mail: WMcShane@cdc.gov; Pappas, R. Steven [Centers for Disease Control and Prevention, Division of Laboratory Sciences, Emergency Response and Air Toxicants, 4770 Buford Highway, MS F-44, Atlanta, GA 30341 (United States)], E-mail: RPappas@cdc.gov; Wilson-McElprang, Veronica [Battelle-Centers for Disease Control and Prevention, Division of Laboratory Sciences, Emergency Response and Air Toxicants Branch, 4770 Buford Highway, MS F-44, Atlanta, GA 30341 (United States)], E-mail: VWilsonMcelprang@cdc.gov; Paschal, Dan [Centers for Disease Control and Prevention, Division of Laboratory Sciences, Emergency Response and Air Toxicants, 4770 Buford Highway, MS F-44, Atlanta, GA 30341 (United States)], E-mail: DPaschal@cdc.gov

2008-06-15

A simple, high-throughput method for determining total cadmium, mercury, and lead in blood in cases of suspected exposure, using inductively coupled plasma-mass spectrometry (ICP-MS), has been developed and validated. One part matrix-matched standards, blanks, or aliquots of blood specimens were diluted with 49 parts of a solution containing 0.25% (w/w) tetramethylammonium hydroxide; 0.05% v/v Triton X-100 (blood cell membranes and protein solubilization); 0.01% (w/v) ammonium pyrolidinedithiocarbamate (mercury memory effect prevention and oxidation state stabilization, solubilization by complexation of all three metals); 1% v/v isopropanol (signal enhancement); and 10 {mu}g/L iridium (internal standard). Thus the final dilution factor is 1 + 49. The method provides the basis for the determination of total cadmium, mercury, and lead for assessment of environmental, occupational, accidental ingestion or elevated exposures from other means. Approximately 80 specimens, including blanks, calibration standards, and quality control materials can be processed in an 8-h day. The method has been evaluated by examining reference materials from the National Institute of Standards and Technology, as well as by participation in six rounds of proficiency testing intercomparisons led by the Wadsworth Center of the New York State Department of Health. This method was developed for the purpose of increasing U.S. emergency response laboratory capacity. To this end, 33 U.S. state, and 1 district health department laboratories have validated this method in their own laboratories.

Temporal dynamics of airborne lead-210 in Missouri (USA): implications for geochronological methods

International Nuclear Information System (INIS)

Sheets, R.W.; Lawrence, A.E.

1999-01-01

Lead-210 ( 210 Pb) deposited from the atmosphere is used in the dating of certain geological materials such as glacial ice and lacustrine sediments, but its long-term atmospheric behavior has been little studied. The present investigation reports measurements of airborne 210 Pb at 21 monitoring stations in Springfield, Missouri, during 1975-1995. Seasonal and diurnal patterns of atmospheric concentrations are established, and the mean annual concentrations of 210 Pb in ground level air during the 20-year period are examined. Although airborne 210 Pb concentrations are found to vary diurnally and seasonally, mean annual concentrations in southwest Missouri have remained relatively constant during this time period. This finding is important for geochronological methods that assume a constant 210 Pb flux from the atmosphere. (orig.)

Synthesis and characterization of lead zirconate titanate powders obtained by the oxidant peroxo method

Energy Technology Data Exchange (ETDEWEB)

Camargo, Emerson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos SP, 13565-905 (Brazil)], E-mail: camargo@ufscar.br; Leite, Edson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos SP, 13565-905 (Brazil)], E-mail: derl@power.ufscar.br; Longo, Elson [Department of Biochemistry, Chemistry Institute of Araraquara, UNESP, Sao Paulo State University Rua Francisco Degni, CP 355 Araraquara SP, 14801-907 Brazil (Brazil)], E-mail: elson@iq.unesp.br

2009-02-05

Lead zirconate titanate (PbZr{sub 1-x}Ti{sub x}O{sub 3}) was synthesized by the 'oxidant peroxo method (OPM)' with 'x' between 0.25 and 0.50. Titanium metal was dissolved into a hydrogen peroxide/ammonia aqueous solution, followed by the addition of lead and zirconium nitrate solution. The amorphous precipitated precursor obtained was crystallized by heat treatment between 400 and 1000 deg. C. Images of transmission microscopy showed spherical particles with average diameter between 20 and 60 nm, and the presence of necks between particles treated at 700 deg. C. All of the unpressed powders were characterized by X-ray diffractometry and FT-Raman spectroscopy. Powder samples with 'x' up to 0.35 showed rhombohedral structure when treated at temperatures higher than 500 deg. C, and tetragonal structure when 'x' was higher than 0.40. Analysis of XRD and Raman spectroscopy of the precursor powders showed amorphous-like structures, however powders treated at 400 deg. C showed a structure identified as an intermediate pyrochlore phase, independently of the Zr and Ti mole ratio.

Comparative study of measured heart cycle phase durations: standard lead ECG versus original ascending aorta lead ECG

Directory of Open Access Journals (Sweden)

Sergey V. Kolmakov

2012-11-01

Full Text Available Aims The present paper aims at evaluating the existing difference in duration measurements of the same heart cycle phases in the standard V3, V4, V5, V6 leads ECG versus original HDA lead ECG of the ascending aorta. Materials and methods The method of changing the filter pass band is used. Its essence is in artificial changing of the conditions of the signal recording carrying the informative indications of the initial information used in hemodynamic equations. The method also enables calculating the percentage deviation from the initial values. The principle of balance of the blood volume entering the heart and the blood volume leaving the heart is used to trace the minimal deviations and their respective recording conditions. Results In each of the V3, V4, V5, V6 ECG leads durations of the same phases have different values. The values measured on the ECG of the ascending aorta and those measured using the standard V4 ECG lead differ slightly. Conclusion For heart cycle phase analysis it is possible to use only the ECG of the ascending aorta and V4 standard lead ECG. Using conventional standard ECG leads causes an error up to 25%.

Development and optimization of a nuclear method to determine the lead concentration as an ultra-trace element in ultra-pure water

International Nuclear Information System (INIS)

Amara, A.; Giovagnoli, A.; Barrandon, J.N.

1994-01-01

Here we intend to perfect a nuclear analytical technique for the determination of lead concentration as an ultra-trace element in ultra-pure water Inmost cases the analysis of an aqueous solution is made by non-nuclear methods, therefore methods which are sensitive to the chemical form of the element to be determined. To ovoid this problem we developed a nuclear technique using a cyclotron,which allows the determination of the lead concentration in any of its chemical forms. We studied the possibilities of several incident beams, like neutral particles and charged particles. Proton activation showed to be the most sensitive of all the irradiation procedures. Several points have though be studied and developed: - an irradiation cell for liquids irradiation under a strong proton current; - the bismuth chemical separation. This element has two radio-isotopes allowing the determination of lead;-optimize the experimental irradiation and measurements parameters in order to reach the lower detection limit. At last an intercomparison of several techniques has been made for different standards. It clearly showed that, contrary to atomic,potentiometric or mass spectrometry methods,only activation technique give accurate and reproducible results. (author).1 fig., 2 tabs., 4 refs

Anemia risk in relation to lead exposure in lead-related manufacturing

Directory of Open Access Journals (Sweden)

Nan-Hung Hsieh

2017-05-01

Full Text Available Abstract Background Lead-exposed workers may suffer adverse health effects under the currently regulated blood lead (BPb levels. However, a probabilistic assessment about lead exposure-associated anemia risk is lacking. The goal of this study was to examine the association between lead exposure and anemia risk among factory workers in Taiwan. Methods We first collated BPb and indicators of hematopoietic function data via health examination records that included 533 male and 218 female lead-exposed workers between 2012 and 2014. We used benchmark dose (BMD modeling to estimate the critical effect doses for detection of abnormal indicators. A risk-based probabilistic model was used to characterize the potential hazard of lead poisoning for job-specific workers by hazard index (HI. We applied Bayesian decision analysis to determine whether BMD could be implicated as a suitable BPb standard. Results Our results indicated that HI for total lead-exposed workers was 0.78 (95% confidence interval: 0.50–1.26 with risk occurrence probability of 11.1%. The abnormal risk of anemia indicators for male and female workers could be reduced, respectively, by 67–77% and 86–95% by adopting the suggested BPb standards of 25 and 15 μg/dL. Conclusions We conclude that cumulative exposure to lead in the workplace was significantly associated with anemia risk. This study suggests that current BPb standard needs to be better understood for the application of lead-exposed population protection in different scenarios to provide a novel standard for health management. Low-level lead exposure risk is an occupational and public health problem that should be paid more attention.

Characterization of dense lead lanthanum titanate ceramics prepared from powders synthesized by the oxidant peroxo method

Energy Technology Data Exchange (ETDEWEB)

Pinto, Alexandre H. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Souza, Flavio L., E-mail: flavio.souza@ufabc.edu.br [Centro de Ciencias Naturais e Humanas, Universidade Federal do ABC, Rua Santa Adelia 166, Bangu, Santo Andre, SP 09210-170 (Brazil); Chiquito, Adenilson J., E-mail: chiquito@df.ufscar.br [Departamento de Fisica, UFSCar-Federal University of Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Longo, Elson, E-mail: elson@iq.unesp.br [Instituto de Quimica de Araraquara, UNESP-Universidade Estadual Paulista, Rua Francisco Degni, CP 355 Araraquara, SP 14801-907 (Brazil); Leite, Edson R., E-mail: derl@power.ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Camargo, Emerson R., E-mail: camargo@ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil)

2010-12-01

Nanosized powders of lead lanthanum titanate (Pb{sub 1-x}La{sub x}TiO{sub 3}) were synthesized by means of the oxidant-peroxo method (OPM). Lanthanum was added from 5 to 30% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of lead nitrate to prepare a solution of lead and lanthanum nitrates, which was dripped into an aqueous solution of titanium peroxo complexes, forming a reactive amorphous precipitate that could be crystallized by heat treatment. Crystallized powders were characterized by FT-Raman spectroscopy and X-ray powder diffraction, showing that tetragonal perovskite structure is obtained for samples up to 25% of lanthanum and cubic perovskite for samples with 30% of lanthanum. Powders containing 25 and 30% in mol of lanthanum were calcined at 700 deg. C for 2 h, and in order to determine the relative dielectric permittivity and the phase transition behaviour from ferroelectric-to-paraelectric, ceramic pellets were prepared and sintered at 1100 or 1150 deg. C for 2 h and subjected to electrical characterization. It was possible to observe that sample containing 25% in mol of La presented a normal behaviour for the phase transition, whereas the sample containing 30% in mol of La presented a diffuse phase transition and relaxor behaviour.

Characterization of dense lead lanthanum titanate ceramics prepared from powders synthesized by the oxidant peroxo method

International Nuclear Information System (INIS)

Pinto, Alexandre H.; Souza, Flavio L.; Chiquito, Adenilson J.; Longo, Elson; Leite, Edson R.; Camargo, Emerson R.

2010-01-01

Nanosized powders of lead lanthanum titanate (Pb 1-x La x TiO 3 ) were synthesized by means of the oxidant-peroxo method (OPM). Lanthanum was added from 5 to 30% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of lead nitrate to prepare a solution of lead and lanthanum nitrates, which was dripped into an aqueous solution of titanium peroxo complexes, forming a reactive amorphous precipitate that could be crystallized by heat treatment. Crystallized powders were characterized by FT-Raman spectroscopy and X-ray powder diffraction, showing that tetragonal perovskite structure is obtained for samples up to 25% of lanthanum and cubic perovskite for samples with 30% of lanthanum. Powders containing 25 and 30% in mol of lanthanum were calcined at 700 deg. C for 2 h, and in order to determine the relative dielectric permittivity and the phase transition behaviour from ferroelectric-to-paraelectric, ceramic pellets were prepared and sintered at 1100 or 1150 deg. C for 2 h and subjected to electrical characterization. It was possible to observe that sample containing 25% in mol of La presented a normal behaviour for the phase transition, whereas the sample containing 30% in mol of La presented a diffuse phase transition and relaxor behaviour.

The comparative study of contents of zinc and lead in ore samples of Namtu-Bawdwin Mine by wet analysis, X-ray fluorescence and X-ray diffraction methods

Energy Technology Data Exchange (ETDEWEB)

Kyaw-Soe,

1990-05-01

Lead-zinc ores taken from Namtu-Bawdwin area had been analyzed by wet processes in the Department of Chemistry, 1984. These ore samples have been analyzed by energy dispersive X-ray fluorescence method in the Department of Physics and X-ray diffraction method is also used to determine elements of lead and zinc compounds in these ore samples in the University`s Research Centre. In brief, we study comparatively the contents of lead and zinc and their compounds using the methods of wet processes, X-ray fluorescence and X-ray diffraction. (author).

The measurement and estimation method of the sorption of lead onto cementitious materials

International Nuclear Information System (INIS)

Nakanishi, Kiyoshi; Tsukamoto, Masaki; Fujita, Tomonari; Sugiyama, Daisuke

2002-01-01

Cementitious material is a potential waste packaging material for radioactive waste disposal, and is expected to provide chemical containment. In particular, the sorption of radionuclides onto cementitious material is a very important parameter when considering the release of radionuclides from radioactive waste. In this study, sorption of lead, onto hydrated Ordinary Portland Cement (OPC), OPC/Blast Furnace Slag blended cement (BFS), Highly containing Flyash and Silica Fume Cement (HFSC) and cement constituent minerals (portlandite, ettringite, hydrotalcite and C-S-H gels (Ca/Si = 0.9 and 1.65)) was measured using the batch sorption technique. Lead is one of the important nuclides for safety assessment. The obtained distribution ratios, Rd values, for sorption of lead onto hydrated (freshly cured) OPC and HFSC are very high:>1000 cm3g-1. The distribution ratio for sorption of lead onto OPC/BFS could not be determined quantitatively due to the precipitation of PbS. Comparing the Rd values onto cements and minerals, it was suggested the sorption onto C-S-H gel phases dominate the sorption for lead onto hydrated cements. Once a cementitious material is altered in the disposal environment, its sorption ability may be affected. The sorption of lead onto degraded OPC and degraded HFSC, which were altered in the presence of distilled water, was also measured. It was observed that the alteration did not cause changes that decreased the sorption of lead onto OPC and HFSC. An approach, in which it is assumed that each of the component phases contributes to the composite material, is proposed and discussed to describe the sorption of lead onto cement using a knowledge of the phase components in a linear additive manner. The results showed reasonably good agreement between the predicted and measured Rd values for lead onto freshly cured and altered cements. (author)

Adequacy and validation of an analytical method for the quantification of lead in chamomile tisanes produced in Costa Rica

International Nuclear Information System (INIS)

Blanco Barrantes, Jeimy

2014-01-01

An analytical methodology is developed and validated to quantify lead in chamomile tisanes. Lead is quantified by utilizing the technique of flame atomic absorption spectroscopy in three brands of chamomile tisanes sold in Costa Rica to determine its safety and quality based on international standards. A method of sample preparation is established through a comparison of different forms of extraction. The acid digestion extraction method has been the procedure utilized, reaching an average recovery percentage of 97,1%, with a standard deviation of 2,3%. The optimization of the chosen analytical procedure and complete validation is performed. The results obtained in the validation of the analytical procedure have shown that the interval where is generated the best calibration curve in terms of the correlation coefficient and the value of the statistically significant intercept equal to zero, have been the comprised between (0,2-3,2) μg/mL (r 2 =0,9996), corresponding to a range between 20% to 320% of the maximum allowed limit. In addition, the procedure has been adequate in terms of accuracy (average recovery percentage 101,1%) and precision under repeatability and intermediate precision (RSD max. 9,3%) and limit of quantification (0,2551 μg/mL). The safety criterion of World Health Organization (WHO) is determined with respect to the concentration of lead in the analyzed products. The 9 analyzed samples of products to prepare chamomile tisanes have stayed without evidencing concentrations of lead above the limit value of 10 μg/g suggested for medicinal herbs by WHO [es

Determination of temperature dependency of material parameters for lead-free alkali niobate piezoceramics by the inverse method

Directory of Open Access Journals (Sweden)

K. Ogo

2016-06-01

Full Text Available Sodium potassium niobate (NKN piezoceramics have been paid much attention as lead-free piezoelectric materials in high temperature devices because of their high Curie temperature. The temperature dependency of their material parameters, however, has not been determined in detail up to now. For this purpose, we exploit the so-called Inverse Method denoting a simulation-based characterization approach. Compared with other characterization methods, the Inverse Method requires only one sample shape of the piezoceramic material and has further decisive advantages. The identification of material parameters showed that NKN is mechanically softer in shear direction compared with lead zirconate titanate (PZT at room temperature. The temperature dependency of the material parameters of NKN was evaluated in the temperature range from 30 °C to 150 °C. As a result, we figured out that dielectric constants and piezoelectric constants show a monotonous and isotropic increment with increasing temperature. On the other hand, elastic stiffness constant c 44 E of NKN significantly decreased in contrast to other elastic stiffness constants. It could be revealed that the decrement of c 44 E is associated with an orthorhombic-tetragonal phase transition. Furthermore, ratio of elastic compliance constants s 44 E / s 33 E exhibited similar temperature dependent behavior to the ratio of piezoelectric constants d15/d33. It is suspected that mechanical softness in shear direction is one origin of the large piezoelectric shear mode of NKN. Our results show that NKN are suitable for high temperature devices, and that the Inverse Method should be a helpful approach to characterize material parameters under their practical operating conditions for NKN.

Blood lead levels and risk factors for lead poisoning among children in Jakarta, Indonesia

Energy Technology Data Exchange (ETDEWEB)

Albalak, Rachel; Noonan, Gary; Buchanan, Sharunda; Flanders, W. Dana; Gotway-Crawford, Carol; Blumenthal, Wendy; Curtis, Gerald; McGeehin, Michael A. [Division of Environmental Hazards and Health Effects, National Center for Environmental Health, Centers for Disease Control and Prevention, 1600 Clifton Rd. Mailstop E-19, Atlanta, GA 30333 (United States); Kim, Dennis; Tan, Regina [Epidemic Intelligence Service, Epidemiology Program Office, Centers for Disease Control and Prevention, 1600 Clifton Rd. Mailstop D-18, Atlanta, GA 30333 (United States); Jones, Robert L. [Division of Laboratory Sciences, National Center for Environmental Health, Centers for Disease Control and Prevention, 1600 Clifton Rd. Mailstop F-18, Atlanta, GA 30333 (United States); Sulaiman, Rini [Swisscontact, Jl. Wijaya XII No. 44, Jakarta (Indonesia) 12160

2003-01-01

The phase-out of leaded gasoline began in Jakarta, Indonesia on July 1, 2001. We evaluated mean blood lead levels (BLLs) and the prevalence of elevated BLLs of Jakarta school children and assessed risk factors for lead exposure in these children before the beginning of the phase-out activities. The study involved a population-based, cross-sectional blood lead survey that included capillary blood lead sampling and a brief questionnaire on risk factors for lead poisoning. A cluster survey design was used. Forty clusters, defined as primary schools in Jakarta, and 15 2nd- and 3rd-grade children in each cluster were randomly selected for participation in the study. The average age of children in this study was 8.6 years (range 6-12) and the geometric mean BLL of the children was 8.6 {mu}g/dl (median: 8.6 {mu}g/dl; range: 2.6-24.1 {mu}g/dl) (n=397). Thirty-five percent of children had BLLs {>=}10 {mu}g/dl and 2.4% had BLLs {>=}20 {mu}g/dl. Approximately one-fourth of children had BLLs 10-14.9 {mu}g/dl. In multivariate models, level of education of the child's primary caregiver, water collection method, home varnishing and occupational recycling of metals, other than lead, by a family member were predictors of log BLLs after adjustment for age and sex. BLLs of children who lived near a highway or major intersection were significantly higher than those of children who lived near a street with little or no traffic when level of education was not included in the model. Water collection method was a significant predictor of BLLs {>=}10 {mu}g/dl after adjustment for age and sex. BLLs in children in this study were moderately high and consistent with BLLs of children in other countries where leaded gasoline is used. With the phase-out of leaded gasoline, BLLs of children in Jakarta are expected to rapidly decline as they have in other countries that have phased lead out of gasoline.

Determination of lead element trace in some Syrian cigarettes and Its mixtures using voltammetric method on HMDE

International Nuclear Information System (INIS)

Nasser, H.; Kabass, H.

2010-01-01

This study aims for estimating of trace for these elements in various brands of Syrian Cigarettes and its mixtures, by using voltammetric method (HMDE) hanging mercury drop elec trod. This method is first used to determined Syrian Cigarettes brand and its mixtures, during this study it was found that we can use it easily with low commission, high sensitivity and accurate results comparing with others studies. We prepare the samples by using reference methods. The samples were collected during two times in one year from the same kinds of samples. We noticed that the high concentrations was (3.795μg/g) in Gitanes samples, and the low concentrations in shame samples was (0.37 μg/g). This study refers that there is different concentrations of lead element in this samples.(author)

Blood Lead Levels and Risk Factors among Preschool Children in a Lead Polluted Area in Taizhou, China

Directory of Open Access Journals (Sweden)

Zhenyan Gao

2017-01-01

Full Text Available Objective. To determine the blood lead levels and identify related risk factors among preschool children in a lead polluted area (Taizhou, China and provide theoretical support for prevention of lead pollution. Methods. A stratified-clustered-random sampling method was used to determine the survey sample. Blood lead levels were determined by the tungsten atomizer absorption spectrophotometer. Results. A total of 2,018 subjects (average age of 59 months; 1,087 boys and 931 girls were included. The arithmetic mean, geometric mean, and median blood lead levels of the preschool children were 56.4 μg/L, 48.9 μg/L, and 46 μg/L. A total of 8.8% children had blood lead levels >100 μg/L and 43.9% had blood lead levels >50 μg/L. Mother’s education level, father’s occupation, decorative tableware, exposure to makeup, and the residential floor were all risk factors for elevated blood lead levels (odds ratios of 1.42, 1.21, 1.11, 1.19, and 1.27, resp., while hand washing before eating food was a protective factor (odds ratio of 0.88. Conclusions. The blood lead levels of preschool children in Taizhou were higher than in other areas in China and in developed countries. Therefore, policies ensuring lead-based industries are not placed in close proximity to residential areas are required.

Isotopic analysis of bullet lead samples

International Nuclear Information System (INIS)

Sankar Das, M.; Venkatasubramanian, V.S.; Sreenivas, K.

1976-01-01

The possibility of using the isotopic composition of lead for the identification of bullet lead is investigated. Lead from several spent bullets were converted to lead sulphide and analysed for the isotopic abundances using an MS-7 mass spectrometer. The abundances are measured relative to that for Pb 204 was too small to permit differentiation, while the range of variation of Pb 206 and Pb 207 and the better precision in their analyses permitted differentiating samples from one another. The correlation among the samples examined has been pointed out. The method is complementary to characterisation of bullet leads by the trace element composition. The possibility of using isotopically enriched lead for tagging bullet lead is pointed out. (author)

Determination of lead in whole blood: Comparison of the LeadCare blood lead testing system with zeeman longitudinal electrothermal atomic absorption spectrometry

International Nuclear Information System (INIS)

Pineau, A.; Viallefont, A.; Fauconneau, B.; Rafael, M.; Guillard, O.

2002-01-01

This study compares the efficiency of blood lead level analysis by graphite furnace atomic absorption spectrometry (GFAAS) and the portable LeadCare Blood lead testing system (LCS). Recoveries of two added lead concentrations of 22 and 42 μg/dL ranged from 102.4 to 105.5% for LCS and from 96.3 to 97.2% for GFAAS. Measurement of a certified sample (Certified Danish Whole Blood) at a blood lead concentration of 26.2 μg/dL gave within- and between-run coefficients of variation which were both approximately 8% by LCS and 2% by GFAAS. Comparison of the tested method (LCS) versus GFAAS from analysis of 76 samples of blood lead collected from workers in different industrial sectors showed imperfect overall correlation (r = 0.95). The LCS is quite suitable for screening purposes, but requires the use of non-frozen blood collected less than 24 h before. Conservative threshold values should be applied when using the LCS for initial screening in the field. (orig.)

Remediation of lead contaminated soil

International Nuclear Information System (INIS)

Urban, W.; Krishnamurthy, S.

1992-01-01

Lead contaminated soil in urban area is of major concern because of the potential health risk to children. Many studies have established a direct correlation between lead in soil and elevated blood lead levels in children. In Minneapolis, Minnesota, Mielke et al. (1983) reported that 50% of the Hmong children with lead poisioning were in areas where soil lead levels were between 500 and 1000 micrograms per gram (ug/g), and 40% of the children suffering from lead poisioning lived in areas where soil lead levels exceeded 1000 ug/g. In urban areas, lead pollution in soil has come from many different sources. The sources include lead paint, lead batteries and automobile exhaust. Olson and Skogerbee (1975) found the following lead compounds in soils where the primary source of pollution was from automobiles: lead sulfate, lead oxide, lead dioxide, lead sulfide, and metallic lead. The primary form of lead found was lead sulfate. Lead sulfate, lead tetraoxide, white lead, and other forms of lead have been used in the manufacture of paints for houses. At present, two remediation techniques, solidification and Bureau of Mines fluosilicic acid leaching, are available for lead-contaminated sites. The objective of the present investigation at the Risk Reduction Engineering Laboratory (RREL), Edison, was to try to solubilize the lead species by appropriate reagents and then recover the contaminants by precipitation as lead sulfate, using environmentally acceptable methods. The apparatus used for mixing was a LabMaster mixer, with variable speed and high-shear impeller. Previous work had used nitric acid for dissolving metallic lead. Owing to the environmental concerns, it was decided to use acetic acid in the presence of oxygen. The theoretical justification for this approach is the favorable redox potential for the reaction between metallic lead, acetic acid, and gaseous oxygen

Lead remediation and changes in human lead exposure: some physiological and biokinetic dimensions.

Science.gov (United States)

Mushak, Paul

2003-02-15

This paper presents a qualitative and quantitative analysis of the various aspects of lead remediation effectiveness with particular reference to human health risk assessment. One of the key elements of lead remediation efforts at such sites as those under the Superfund program deals with populations at elevated exposure and toxicity risk in the proximity of, or at, the site of remediation, especially remediation workers, workers at other tasks on sites that were remediated down to some action level of lead concentration in soils, and groups at risk in nearby communities. A second element has to do with how one measures or models lead exposure changes with special reference to baseline and post-remediation conditions. Various biomarkers of lead exposure can be employed, but their use requires detailed knowledge of what results using each means. The most commonly used approach is measurement of blood lead (Pb-B). Recognized limitations in the use of Pb-B has led to the use of predictive Pb exposure models, which are less vulnerable to the many behavioral, physiological, and environmental parameters that can distort isolated or 'single shot' Pb-B testings. A third aspect covered in this paper presents various physiological factors that affect the methods by which one evaluates Pb remediation effectiveness. Finally, this article offers an integrated look at how lead remediation actions directed at one lead source or pathway affect the total lead exposure picture for human populations at elevated lead exposure and toxicity risk.

A simple method to identify radiation and annealing biases that lead to worst-case CMOS static RAM postirradiation response

International Nuclear Information System (INIS)

Fleetwood, D.M.; Dressendorfer, P.V.

1987-01-01

The authors illustrate a simple method to identify bias conditions that lead to worst-case postirradiation speed and timing response for SRAMs. Switching cell states between radiation and anneal should lead to maximum speed and timing degradation for many hardened designs and technologies. The greatest SRAM cell imbalance is also established by these radiation and annealing conditions for the hardened and commercial parts that we have examined. These results should provide insight into the behavior of SRAMs during and after irradiation. The results should also be useful to establishing guidelines for integrated-circuit functionality testing, and SEU and dose-rate upset testing, after total-dose irradiation

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.

1994-01-01

Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially of planned decommissioning operations. Thus lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for contaminated lead is removing the superficial layer of contamination with an abrasive medium under pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a scaled-off area. The slurry of abrasive and particles of lead falls through a floor and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling

Serum Neuron-Specific Enolase, Biogenic Amino-Acids and Neurobehavioral Function in Lead-Exposed Workers from Lead-Acid Battery Manufacturing Process

OpenAIRE

K Ravibabu; T Barman; HR Rajmohan

2015-01-01

Background: The interaction between serum neuron-specific enolase (NSE), biogenic amino-acids and neurobehavioral function with blood lead levels in workers exposed to lead form lead-acid battery manufacturing process was not studied. Objective: To evaluate serum NSE and biogenic amino-acids (dopamine and serotonin) levels, and neurobehavioral performance among workers exposed to lead from lead-acid storage battery plant, and its relation with blood lead levels (BLLs). Methods: In a c...

Lead exposure in US worksites: A literature review and development of an occupational lead exposure database from the published literature

Science.gov (United States)

Koh, Dong-Hee; Locke, Sarah J.; Chen, Yu-Cheng; Purdue, Mark P.; Friesen, Melissa C.

2016-01-01

Background Retrospective exposure assessment of occupational lead exposure in population-based studies requires historical exposure information from many occupations and industries. Methods We reviewed published US exposure monitoring studies to identify lead exposure measurement data. We developed an occupational lead exposure database from the 175 identified papers containing 1,111 sets of lead concentration summary statistics (21% area air, 47% personal air, 32% blood). We also extracted ancillary exposure-related information, including job, industry, task/location, year collected, sampling strategy, control measures in place, and sampling and analytical methods. Results Measurements were published between 1940 and 2010 and represented 27 2-digit standardized industry classification codes. The majority of the measurements were related to lead-based paint work, joining or cutting metal using heat, primary and secondary metal manufacturing, and lead acid battery manufacturing. Conclusions This database can be used in future statistical analyses to characterize differences in lead exposure across time, jobs, and industries. PMID:25968240

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.W.

1993-01-01

Lead used for shielding is often surface contaminated with radionuclides and is therefore a Resource Conservation and Recovery Act (RCRA) D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Lab. decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 100 metric tons and likely to grow substantially because of planned decommissioning operations. This lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for decontaminating lead is removing the thin superficial layer of contamination with an abrasive medium under pressure. For lead, a mixture of alumina with water and air at about 280 kPa (40 psig) rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a sealed-off area. The slurry of abrasive and particles of lead falls through a floor grating and is collected in a pump. A pump sends the slurry mixture back to the spray gun, creating a continuous process

Erythrocyte fluorescence and lead intoxication.

Science.gov (United States)

Clark, K G

1976-01-01

Blood samples from people exposed to inorganic lead were examined by fluorescence microscopy for excess erythrocyte porphyrin. With continued lead absorption, fluorescent erythrocytes appeared in the circulation of workers handling this metal or its compounds, and they progressively increased in number and brilliance. These changes ensued if the blood lead concentration was maintained above 2-42 mumol/l (50 mug/100 ml), and preceded any material fall in the haemoglobin value. At one factory, 62-5% of 81 symptomless workers showed erythrocyte fluorescence attributable to the toxic effects of lead. Excess fluorocytes were found in blood samples from a child with pica and three of her eight siblings. These four were subsequently shown to have slightly increased blood lead concentrations (2-03 to 2-32 mumol/l). Fluorescence microscopy for excess erythrocyte porphyrin is a sensitive method for the detection of chronic lead intoxication. A relatively slight increase in the blood lead is associated with demonstrabel changes in erythrocyte porphyrin content. The procedure requires little blood, and may be performed upon stored samples collected for lead estimation. The results are not readily influenced by contamination, and provide good confirmatory evidence for the absorption of biochemically active lead. PMID:963005

Development of an airborne lead analysis kit and its application.

Science.gov (United States)

Kongtip, Pornpimol; Borisut, Pornchulee; Yoosook, Witaya; Osiri, Pramuk; Rojanavipart, Piangchan

2010-11-01

We developed a method to analyze airborne lead concentrations in the field. It was a modification of the colorimetric method using the reaction between 4(2-pyridylazo)-resorcinol (PAR) and lead with cyanex302 in an acid medium to reduce interfering metals. The lead concentration was detected with a photometer made in Thailand. The developed method uses an impinger containing 1% nitric acid solution as an absorbing agent to collect airborne lead at a flow rate of less than or equal to one liter/minute. Cyanex302 solution in toluene was used to extract metals from the samples and 0.1M nitric acid was used to extract just lead. The lead solution was reacted in 0.5 ml of 0.03% PAR solution, with 1 ml ammonium chloride buffer; the absorption of this solution was measured by a photometer. The results show the limit of detection (LOD) was 0.01 mg/l. The limit of quantification (LOQ) was 0.03 mg/l. The percent recovery of the lead concentrations of 0.05 - 3.0 mg/l was 94.0 to 103.5%. The precision presented as %CV ranged from 0.65 to 10.27%. Lead concentration in a lead smelting factory detected by this method was not significantly different from that detected by the NIOSH method: 7,303 at a 95% confidence level.

Association of Lead Levels and Cerebral Palsy

Science.gov (United States)

Bansal, Neha; Aggarwal, Anju; Faridi, M. M. A.; Sharma, Tusha; Baneerjee, B. D.

2017-01-01

Background: Cerebral palsy is a common motor disability in childhood. Raised lead levels affect cognition. Children with cerebral palsy may have raised lead levels, further impairing their residual cognitive motor and behavioral abilities. Environmental exposure and abnormal eating habits may lead to increased lead levels. Aims and Objectives: To measure blood lead levels in children with cerebral palsy and compare them with healthy neurologically normal children. To correlate blood lead levels with environmental factors. Material and Methods: Design: Prospective case-control study. Setting: Tertiary care hospital. Participants: Cases comprised 34 children with cerebral palsy, and controls comprised 34 neurologically normal, age- and sex-matched children. Methods: Clinical and demographic details were recorded as per proforma. Detailed environmental history was recorded to know the source of exposure to lead. These children were investigated and treated as per protocol. Venous blood was collected in ethylenediaminetetraacetic acid vials for analysis of blood lead levels. Lead levels were estimated by Schimadzu Flame AA-6800 (atomic absorption spectrophotometer). Data were analyzed using SPSS version 17. P pica were 12.33 ± 10.02 µg/dL in comparison to children with no history of pica, 6.70 ± 4.60 µg/dL (P = .029). No correlation was found between hemoglobin and blood lead levels in cases and controls. Conclusion: In our study, blood lead levels are raised in children with cerebral palsy. However, further studies are required to show effects of raised levels in these children. PMID:28491920

40 CFR Appendix G to Part 50 - Reference Method for the Determination of Lead in Suspended Particulate Matter Collected From...

Science.gov (United States)

2010-07-01

... minimize the possibility of generating unreliable data, the user should follow practices established for... chapter—Modifications of methods by users. (Guidance or assistance in requesting approval under Section 2... lead content of the sample is analyzed by atomic absorption spectrometry using an air-acetylene flame...

Decontaminating lead bricks and shielding

International Nuclear Information System (INIS)

Lussiez, G.W.

1993-01-01

Lead used for shielding is often surface contaminated with radioisotopes and is therefore a RCRA D008 mixed waste. The technology-based standard for treatment is macroencapsulation. However, decontaminating and recycling the clean lead is a more attractive solution. Los Alamos National Laboratory decontaminates material and equipment contaminated with radioisotopes. Decontaminating lead poses special problems because of the RCRA hazard classification and the size of the inventory, now about 50 tons and likely to grow substantially because of planned decommissioning operations. This lead, in the form of bricks and other shield shapes, is surface contaminated with fission products. One of the best methods for decontaminating lead is removing the thin superficial layer of contamination with an abrasive medium trader pressure. For lead, a mixture of alumina with water and air at about 40 psig rapidly and effectively decontaminates the lead. The abrasive medium is sprayed onto the lead in a sealed-off area. The slurry of abrasive and particles of lead falls through a floor grating and is collected in a sump. A pump sends the slurry mixture back to the spray gun, creating a continuous process. The process generates small volumes of contaminated lead slurry that can be solidified and, because it passes the TCLP, is not a mixed waste. The decontaminated lead can be released for recycling

Lead isotope analyses of standard rock samples

International Nuclear Information System (INIS)

Koide, Yoshiyuki; Nakamura, Eizo

1990-01-01

New results on lead isotope compositions of standard rock samples and their analytical procedures are reported. Bromide form anion exchange chromatography technique was adopted for the chemical separation lead from rock samples. The lead contamination during whole analytical procedure was low enough to determine lead isotope composition of common natural rocks. Silica-gel activator method was applied for emission of lead ions in the mass spectrometer. Using the data reduction of 'unfractionated ratios', we obtained good reproducibility, precision and accuracy on lead isotope compositions of NBS SRM. Here we present new reliable lead isotope compositions of GSJ standard rock samples and USGS standard rock, BCR-1. (author)

Method to reduce contamination and uptake of lead by plants from car exhaust gases

Energy Technology Data Exchange (ETDEWEB)

Isermann, K.

1977-03-01

Splashing and/or washing plants with aqueous solutions of the chelates CaEDTA (max. 5 mM/litre) or Na-polyphosphate (max. 0.5 percent) is an effective way of reducing contamination and uptake of lead by plants within regions where lead is emitted at significant levels. By chelating lead it first becomes unloaded or even negatively charged (for instance with EDTA as Pb/sub 2/EDTA or PbHEDTA/sup 1 -/ and PbEDTA/sup 2 -/). Therefore chelated lead, in contrast to normal Pb/sup 2 +/, is not absorbed, either on negatively charged surfaces of the plants (cuticula) or within the plant-tissue (mesophyll, on negatively charged cell-walls or membranes). Also, Pb-chelate has a larger diameter than bivalent Pb/sup 2 +/, resulting in a restricted lead uptake by the plant roots.

Association of Lead Levels and Cerebral Palsy

Directory of Open Access Journals (Sweden)

Neha Bansal MD

2017-03-01

Full Text Available Background: Cerebral palsy is a common motor disability in childhood. Raised lead levels affect cognition. Children with cerebral palsy may have raised lead levels, further impairing their residual cognitive motor and behavioral abilities. Environmental exposure and abnormal eating habits may lead to increased lead levels. Aims and Objectives: To measure blood lead levels in children with cerebral palsy and compare them with healthy neurologically normal children. To correlate blood lead levels with environmental factors. Material and Methods: Design: Prospective case-control study. Setting: Tertiary care hospital. Participants: Cases comprised 34 children with cerebral palsy, and controls comprised 34 neurologically normal, age- and sex-matched children. Methods: Clinical and demographic details were recorded as per proforma. Detailed environmental history was recorded to know the source of exposure to lead. These children were investigated and treated as per protocol. Venous blood was collected in ethylenediaminetetraacetic acid vials for analysis of blood lead levels. Lead levels were estimated by Schimadzu Flame AA-6800 (atomic absorption spectrophotometer. Data were analyzed using SPSS version 17. P < .05 was taken as significant. Results: Mean blood lead levels were 9.20 ± 8.31 µg/dL in cerebral palsy cases and 2.89 ± 3.04 µg/dL in their controls (P < .001. Among children with cerebral palsy, 19 (55.88% children had blood lead levels ≥5 µg/dL. Lead levels in children with pica were 12.33 ± 10.02 µg/dL in comparison to children with no history of pica, 6.70 ± 4.60 µg/dL (P = .029. No correlation was found between hemoglobin and blood lead levels in cases and controls. Conclusion: In our study, blood lead levels are raised in children with cerebral palsy. However, further studies are required to show effects of raised levels in these children.

Systematic Design of the Lead-Lag Network Method for Active Damping in LCL-Filter Based Three Phase Converters

DEFF Research Database (Denmark)

Alzola, Rafael Pena; Liserre, Marco; Blaabjerg, Frede

2014-01-01

) nor its rationale has been explained. Thus, in this paper a straightforward procedure is developed to tune the lead-lag network with the help of software tools. The rationale of this procedure, based on the capacitor current feedback, is elucidated. Stability is studied by means of the root locus......Three-phase active rectifiers guarantee sinusoidal input currents and unity power factor at the price of a high switching frequency ripple. To adopt an LCL-filter, instead of an L-filter, allows using reduced values for the inductances and so preserving dynamics. However, stability problems can...... without using dissipative elements but, sometimes, needing additional sensors. This solution has been addressed in many publications. The lead-lag network method is one of the first reported procedures and continues being in use. However, neither there is a direct tuning procedure (without trial and error...

Assessment of the effectiveness of attenuation of leaded aprons through TLD dosimetry and Monte Carlo simulation method

Energy Technology Data Exchange (ETDEWEB)

Olaya D, H.; Diaz M, J. A.; Martinez O, S. A. [Universidad Pedagogica y Tecnologica de Colombia, Grupo de Fisica Nuclear Aplicada y Simulacion, 150003 Tunja, Boyaca (Colombia); Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico)

2016-10-15

Were performed experimental setups using an X-ray equipment continuous emission Pantak DXT-3000 and three types of leaded aprons with thickness of 0.25, 0.5 and 0.75 mm coated with Mylar Fiber coated Mylar on its surface. Apron was located at a distance of 2.5 m with respect focus in order to cover a radiation field size of a meter in diameter. At the beam output were added aluminum filtration in order to reproduce qualities of narrow beams N-40 (E{sub efective} = 33 keV), N-80 (E{sub efective} = 65 keV) and N-100 (E{sub efective} = 83 keV) according to the ISO standard 4037 (1-3). Each lead apron were fixed 10 TLD dosimeters over its surface, 5 dosimeters before and 5 dosimeters after with respect to X-ray beam and were calibrated for Harshaw 4500 thermoluminescent reader system order to assess the attenuation of each apron. Were performed dosimeters readings and were calculated the attenuation coefficients for each effective energy of X-ray quality. In order to confirm the method of effective energy of ISO-4037 and evaluate effectiveness of lead aprons based on energy range for each medical practice was made a Monte Carlo simulation using code GEANT-4, calculating the fluence and absorbed dose in each one of the dosimeters Monte Carlo, then coefficients of linear attenuation were calculated and compared with the experimental data and reported by the National Institute of Standards and Technology (Nist). Finally, results are consistent between theoretical calculation and experimental measures. This work will serve to make assessments for other personalized leaded protections. (Author)

A novel surface cleaning method for chemical removal of fouling lead layer from chromium surfaces

International Nuclear Information System (INIS)

Gholivand, Kh.; Khosravi, M.; Hosseini, S.G.; Fathollahi, M.

2010-01-01

Most products especially metallic surfaces require cleaning treatment to remove surface contaminations that remain after processing or usage. Lead fouling is a general problem which arises from lead fouling on the chromium surfaces of bores and other interior parts of systems which have interaction with metallic lead in high temperatures and pressures. In this study, a novel chemical solution was introduced as a cleaner reagent for removing metallic lead pollution, as a fouling metal, from chromium surfaces. The cleaner aqueous solution contains hydrogen peroxide (H 2 O 2 ) as oxidizing agent of lead layer on the chromium surface and acetic acid (CH 3 COOH) as chelating agent of lead ions. The effect of some experimental parameters such as acetic acid concentration, hydrogen peroxide concentration and temperature of the cleaner solution during the operation on the efficiency of lead cleaning procedure was investigated. The results of scanning electron microscopy (SEM) showed that using this procedure, the lead pollution layer could be completely removed from real chromium surfaces without corrosion of the original surface. Finally, the optimum conditions for the complete and fast removing of lead pollution layer from chromium surfaces were proposed. The experimental results showed that at the optimum condition (acetic acid concentration 28% (V/V), hydrogen peroxide 8% (V/V) and temperature 35 deg. C), only 15-min time is needed for complete removal of 3 g fouling lead from a chromium surface.

Cadmium and lead determination by ICPMS: Method optimization and application in carabao milk samples

Directory of Open Access Journals (Sweden)

Riza A. Magbitang

2012-06-01

Full Text Available A method utilizing inductively coupled plasma mass spectrometry (ICPMS as the element-selective detector with microwave-assisted nitric acid digestion as the sample pre-treatment technique was developed for the simultaneous determination of cadmium (Cd and lead (Pb in milk samples. The estimated detection limits were 0.09ìg kg-1 and 0.33ìg kg-1 for Cd and Pb, respectively. The method was linear in the concentration range 0.01 to 500ìg kg-1with correlation coefficients of 0.999 for both analytes.The method was validated using certified reference material BCR 150 and the determined values for Cd and Pb were 18.24 ± 0.18 ìg kg-1 and 807.57 ± 7.07ìg kg-1, respectively. Further validation using another certified reference material, NIST 1643e, resulted in determined concentrations of 6.48 ± 0.10 ìg L-1 for Cd and 21.96 ± 0.87 ìg L-1 for Pb. These determined values agree well with the certified values in the reference materials.The method was applied to processed and raw carabao milk samples collected in Nueva Ecija, Philippines.The Cd levels determined in the samples were in the range 0.11 ± 0.07 to 5.17 ± 0.13 ìg kg-1 for the processed milk samples, and 0.11 ± 0.07 to 0.45 ± 0.09 ìg kg-1 for the raw milk samples. The concentrations of Pb were in the range 0.49 ± 0.21 to 5.82 ± 0.17 ìg kg-1 for the processed milk samples, and 0.72 ± 0.18 to 6.79 ± 0.20 ìg kg-1 for the raw milk samples.

In vivo x-ray fluorescence of bone lead in the study of human lead metabolism: Serum lead, whole blood lead, bone lead, and cumulative exposure

International Nuclear Information System (INIS)

Cake, K.M.; Chettle, D.R.; Webber, C.E.; Gordon, C.L.

1995-01-01

Traditionally, clinical studies of lead's effect on health have relied on blood lead levels to indicate lead exposure. However, this is unsatisfactory because blood lead levels have a half-life of approximately 5 weeks, and thus reflect recent exposure. Over 90% of the lead body burden is in bone, and it is thought to have a long residence time, thus implying that measurements of bone lead reflect cumulative exposure. So, measurements of bone lead are useful in understanding the long-term health effects of lead. Ahlgren reported the first noninvasive measurements of bone lead in humans, where γ-rays from 57 Co were used to excite the K series x-rays of lead. The lead detection system at McMaster University uses a 109 Cd source which is positioned at the center of the detector face (HPGe) and a near backscatter (∼160 degrees) geometry. This arrangement allows great flexibility, since one can sample lead in a range of different bone sites due to a robust normalization technique which eliminates the need to correct for bone geometry, thickness of overlying tissue, and other related factors. The effective radiation dose to an adult during an x-ray fluorescence bone lead measurement is extremely low, being 35 nSv. This paper addresses the issue of how bone, whole blood, and serum lead concentrations can be related in order to understand a person's lead exposure history

Applicability of linearized-theory attached-flow methods to design and analysis of flap systems at low speeds for thin swept wings with sharp leading edges

Science.gov (United States)

Carlson, Harry W.; Darden, Christine M.

1987-01-01

Low-speed experimental force and data on a series of thin swept wings with sharp leading edges and leading and trailing-edge flaps are compared with predictions made using a linearized-theory method which includes estimates of vortex forces. These comparisons were made to assess the effectiveness of linearized-theory methods for use in the design and analysis of flap systems in subsonic flow. Results demonstrate that linearized-theory, attached-flow methods (with approximate representation of vortex forces) can form the basis of a rational system for flap design and analysis. Even attached-flow methods that do not take vortex forces into account can be used for the selection of optimized flap-system geometry, but design-point performance levels tend to be underestimated unless vortex forces are included. Illustrative examples of the use of these methods in the design of efficient low-speed flap systems are included.

Determination of Lead in Blood by Atomic Absorption Spectrophotometry1

Science.gov (United States)

Selander, Stig; Cramér, Kim

1968-01-01

Lead in blood was determined by atomic absorption spectrophotometry, using a wet ashing procedure and a procedure in which the proteins were precipitated with trichloroacetic acid. In both methods the lead was extracted into isobutylmethylketone before measurement, using ammonium pyrrolidine dithiocarbamate as chelator. The simpler precipitation procedure was shown to give results identical with those obtained with the ashing technique. In addition, blood specimens were examined by the precipitation method and by spectral analysis, which method includes wet ashing of the samples, with good agreement. All analyses were done on blood samples from `normal' persons or from lead-exposed workers, and no additions of inorganic lead were made. The relatively simple protein precipitation technique gave accurate results and is suitable for the large-scale control of lead-exposed workers. PMID:5663425

Assessment of the effectiveness of attenuation of leaded aprons through TLD dosimetry and Monte Carlo simulation method

International Nuclear Information System (INIS)

Olaya D, H.; Diaz M, J. A.; Martinez O, S. A.; Vega C, H. R.

2016-10-01

Were performed experimental setups using an X-ray equipment continuous emission Pantak DXT-3000 and three types of leaded aprons with thickness of 0.25, 0.5 and 0.75 mm coated with Mylar Fiber coated Mylar on its surface. Apron was located at a distance of 2.5 m with respect focus in order to cover a radiation field size of a meter in diameter. At the beam output were added aluminum filtration in order to reproduce qualities of narrow beams N-40 (E_e_f_e_c_t_i_v_e = 33 keV), N-80 (E_e_f_e_c_t_i_v_e = 65 keV) and N-100 (E_e_f_e_c_t_i_v_e = 83 keV) according to the ISO standard 4037 (1-3). Each lead apron were fixed 10 TLD dosimeters over its surface, 5 dosimeters before and 5 dosimeters after with respect to X-ray beam and were calibrated for Harshaw 4500 thermoluminescent reader system order to assess the attenuation of each apron. Were performed dosimeters readings and were calculated the attenuation coefficients for each effective energy of X-ray quality. In order to confirm the method of effective energy of ISO-4037 and evaluate effectiveness of lead aprons based on energy range for each medical practice was made a Monte Carlo simulation using code GEANT-4, calculating the fluence and absorbed dose in each one of the dosimeters Monte Carlo, then coefficients of linear attenuation were calculated and compared with the experimental data and reported by the National Institute of Standards and Technology (Nist). Finally, results are consistent between theoretical calculation and experimental measures. This work will serve to make assessments for other personalized leaded protections. (Author)

Are automated molecular dynamics simulations and binding free energy calculations realistic tools in lead optimization? An evaluation of the linear interaction energy (LIE) method

NARCIS (Netherlands)

Stjernschantz, E.M.; Marelius, J.; Medina, C.; Jacobsson, M.; Vermeulen, N.P.E.; Oostenbrink, C.

2006-01-01

An extensive evaluation of the linear interaction energy (LIE) method for the prediction of binding affinity of docked compounds has been performed, with an emphasis on its applicability in lead optimization. An automated setup is presented, which allows for the use of the method in an industrial

Moveable Leading Edge Device for a Wing

Science.gov (United States)

Pitt, Dale M. (Inventor); Eckstein, Nicholas Stephen (Inventor)

2013-01-01

A method and apparatus for managing a flight control surface system. A leading edge section on a wing of an aircraft is extended into a deployed position. A deformable section connects the leading edge section to a trailing section. The deformable section changes from a deformed shape to an original shape when the leading edge section is moved into the deployed position. The leading edge section on the wing is moved from the deployed position to an undeployed position. The deformable section changes to the deformed shape inside of the wing.

Current practice in transvenous lead extraction

DEFF Research Database (Denmark)

Bongiorni, Maria Grazia; Blomström-Lundqvist, Carina; Kennergren, Charles

2012-01-01

AIM: Current practice with regard to transvenous lead extraction among European implanting centres was analysed by this survey. METHODS AND RESULTS: Among all contacted centres, 164, from 30 countries, declared that they perform transvenous lead extraction and answered 58 questions...... with a compliance rate of 99.9%. Data from the survey show that there seems to be an overall increasing experience of managing various techniques of lead extraction and a widespread involvement of cardiac centres in this treatment. Results and complication rates seem comparable with those of main international...... registries. CONCLUSION: This survey gives an interesting snapshot of lead extraction in Europe today and gives some clues for future research and prospective European registries....

The lead cooled fast reactor benchmark Brest-300: analysis with sensitivity method

International Nuclear Information System (INIS)

Smirnov, V.; Orlov, V.; Mourogov, A.; Lecarpentier, D.; Ivanova, T.

2005-01-01

Lead cooled fast neutrons reactor is one of the most interesting candidates for the development of atomic energy. BREST-300 is a 300 MWe lead cooled fast reactor developed by the NIKIET (Russia) with a deterministic safety approach which aims to exclude reactivity margins greater than the delayed neutron fraction. The development of innovative reactors (lead coolant, nitride fuel...) and fuel cycles with new constraints such as cycle closure or actinide burning, requires new technologies and new nuclear data. In this connection, the tool and neutron data used for the calculational analysis of reactor characteristics requires thorough validation. NIKIET developed a reactor benchmark fitting of design type calculational tools (including neutron data). In the frame of technical exchanges between NIKIET and EDF (France), results of this benchmark calculation concerning the principal parameters of fuel evolution and safety parameters has been inter-compared, in order to estimate the uncertainties and validate the codes for calculations of this new kind of reactors. Different codes and cross-sections data have been used, and sensitivity studies have been performed to understand and quantify the uncertainties sources.The comparison of results shows that the difference on k eff value between ERANOS code with ERALIB1 library and the reference is of the same order of magnitude than the delayed neutron fraction. On the other hand, the discrepancy is more than twice bigger if JEF2.2 library is used with ERANOS. Analysis of discrepancies in calculation results reveals that the main effect is provided by the difference of nuclear data, namely U 238 , Pu 239 fission and capture cross sections and lead inelastic cross sections

Bromine pretreated chitosan for adsorption of lead

Indian Academy of Sciences (India)

Pollution by heavy metals like lead (II) is responsible for health hazards and environmental degradation. Adsorption is a prevalent method applied for removal of heavy metal pollutants from water. This study explored adsorption performances of 30% bromine pretreated chitosan for lead (II) abatement from water. Bromine ...

Cumulant generating function formula of heat transfer in ballistic systems with lead-lead coupling

Science.gov (United States)

Li, Huanan; Agarwalla, Bijay Kumar; Wang, Jian-Sheng

2012-10-01

Based on a two-time observation protocol, we consider heat transfer in a given time interval tM in a lead-junction-lead system taking coupling between the leads into account. In view of the two-time observation, consistency conditions are carefully verified in our specific family of quantum histories. Furthermore, its implication is briefly explored. Then using the nonequilibrium Green's function method, we obtain an exact formula for the cumulant generating function for heat transfer between the two leads, valid in both transient and steady-state regimes. Also, a compact formula for the cumulant generating function in the long-time limit is derived, for which the Gallavotti-Cohen fluctuation symmetry is explicitly verified. In addition, we briefly discuss Di Ventra's repartitioning trick regarding whether the repartitioning procedure of the total Hamiltonian affects the nonequilibrium steady-state current fluctuation. All kinds of properties of nonequilibrium current fluctuations, such as the fluctuation theorem in different time regimes, could be readily given according to these exact formulas.

Determination of temperature dependence of piezoelectric coefficients matrix of lead zirconate titanate ceramics by quasi-static and resonance method

International Nuclear Information System (INIS)

Li Fei; Xu Zhuo; Wei Xiaoyong; Yao Xi

2009-01-01

The piezoelectric coefficients (d 33 , -d 31 , d 15 , g 33 , -g 31 , g 15 ) of soft and hard lead zirconate titanate ceramics were measured by the quasi-static and resonance methods, at temperatures from 20 to 300 0 C. The results showed that the piezoelectric coefficients d 33 , -d 31 and d 15 obtained by these two methods increased with increasing temperature for both hard and soft PZT ceramics, while the piezoelectric coefficients g 33 , -g 31 and g 15 decreased with increasing temperature for both hard and soft PZT ceramics. In this paper, the observed results were also discussed in terms of intrinsic and extrinsic contributions to piezoelectric response.

Determination of Lead in Urine by Atomic Absorption Spectrophotometry1

Science.gov (United States)

Selander, Stig; Cramé, Kim

1968-01-01

A method for the determination of lead in urine by means of atomic absorption spectrophotometry (AAS) is described. A combination of wet ashing and extraction with ammonium pyrrolidine dithiocarbamate into isobutylmethylketone was used. The sensitivity was about 0·02 μg./ml. for 1% absorption, and the detection limit was about 0·02 μg./ml. with an instrumental setting convenient for routine analyses of urines. Using the scale expansion technique, the detection limit was below 0·01 μg./ml., but it was found easier to determine urinary lead concentrations below 0·05 μg./ml. by concentrating the lead in the organic solvent by increasing the volume of urine or decreasing that of the solvent. The method was applied to fresh urines, stored urines, and to urines, obtained during treatment with chelating agents, of patients with lead poisoning. Urines with added inorganic lead were not used. The results agreed well with those obtained with a colorimetric dithizone extraction method (r = 0·989). The AAS method is somewhat more simple and allows the determination of smaller lead concentrations. PMID:5647975

Lead Apron Inspection Using Infrared Light: A Model Validation Study.

Science.gov (United States)

McKenney, Sarah E; Otero, Hansel J; Fricke, Stanley T

2018-02-01

To evaluate defect detection in radiation protective apparel, typically called lead aprons, using infrared (IR) thermal imaging. The use of IR lighting eliminates the need for access to x-ray-emitting equipment and radiation dose to the inspector. The performance of radiation workers was prospectively assessed using both a tactile inspection and the IR inspection with a lead apron phantom over a 2-month period. The phantom was a modified lead apron with a series of nine holes of increasing diameter ranging from 2 to 35 mm in accordance with typical rejection criteria. Using the tactile method, a radiation worker would feel for the defects in the lead apron. For the IR inspection, a 250-W IR light source was used to illuminate the lead apron phantom; an IR camera detected the transmitted radiation. The radiation workers evaluated two stills from the IR camera. From the 31 participants inspecting the lead apron phantom with the tactile method, only 2 participants (6%) correctly discovered all 9 holes and 1 participant reported a defect that was not there; 10 of the 20 participants (50%) correctly identified all 9 holes using the IR method. Using a weighted average, 5.4 defects were detected with the tactile method and 7.5 defects were detected with the IR method. IR light can penetrate an apron's protective outer fabric and illuminate defects below the current standard rejection size criteria. The IR method improves defect detectability as compared with the tactile method. Copyright © 2017 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Topics in perturbative QCD beyond the leading order

International Nuclear Information System (INIS)

Buras, A.J.

1979-08-01

The basic structure of QCD formulae for various inclusive and semi-inclusive processes is presented. Next to leading order QCD corrections to inclusive deep-inelastic scattering are discussed in some detail. The methods for calculations of QCD corrections (leading, next to leading) to semi-inclusive processes are outlined. Some results of these calculations are discussed. 58 references

BLOOD LEAD CONCENTRATION AND DELAYED PUBERTY IN GIRLS

Science.gov (United States)

Background Environmental lead exposure has been linked to alterations in growth and endocrine function. It is not known whether such exposure affects pubertal development.Methods We analyzed the relations between blood lead concentration and pubertal...

{beta}-adrenergic receptor density and adenylate cyclase activity in lead-exposed rat brain after cessation of lead exposure

Energy Technology Data Exchange (ETDEWEB)

Chang, Huoy-Rou [I-Shou University, Department of Biomedical Engineering, Dashu Shiang, Kaohsiung County (Taiwan); Tsao, Der-An [Fooyin University of Technology, Department of Medical Technology (Taiwan); Yu, Hsin-Su [Taiwan University, Department of Dermatology, College of Medicine (Taiwan); Ho, Chi-Kung [Kaohsiung Medical University, Occupational Medicine (Taiwan); Kaohsiung Medical University, Graduate Institute of Medicine, Research Center for Occupational Disease (Taiwan)

2005-01-01

To understanding the reversible or irreversible harm to the {beta}-adrenergic system in the brain of lead-exposed rats, this study sets up an animal model to estimate the change in the sympathetic nervous system of brain after lead exposure was withdrawn. We address the following topics in this study: (a) the relationship between withdrawal time of lead exposure and brain {beta}-adrenergic receptor, blood lead level, and brain lead level in lead-exposed rats after lead exposure was stopped; and (b) the relationship between lead level and {beta}-adrenergic receptor and cyclic AMP (c-AMP) in brain. Wistar rats were chronically fed with 2% lead acetate and water for 2 months. Radioligand binding was assayed by a method that fulfilled strict criteria of {beta}-adrenergic receptor using the ligand [{sup 125}I]iodocyanopindolol. The levels of lead were determined by electrothermal atomic absorption spectrometry. The c-AMP level was determined by radioimmunoassay. The results showed a close relationship between decreasing lead levels and increasing numbers of brain {beta}-adrenergic receptors and brain adenylate cyclase activity after lead exposure was withdrawn. The effect of lead exposure on the {beta}-adrenergic system of the brain is a partly reversible condition. (orig.)

Gammatography of thick lead vessels

International Nuclear Information System (INIS)

Raghunath, V.M.; Bhatnagar, P.K.; Sundaram, V.M.

1979-01-01

Radiography, scintillation and GM counting and dose measurements using ionisation chamber equipment are commonly used for detecting flaws/voids in materials. The first method is mostly used for steel vessels and to a lesser extent thin lead vessels also and is essentially qualitative. Dose measuring techniques are used for very thick and large lead vessels for which high strength radioactive sources are required, with its inherent handling problems. For vessels of intermediate thicknesses, it is ideal to use a small strength source and a GM or scintillation counter assembly. At the Reactor Research Centre, Kalpakkam, such a system was used for checking three lead vessels of thicknesses varying from 38mm to 65mm. The tolerances specified were +- 4% variation in lead thickness. The measurements also revealed the non concentricity of one vessel which had a thickness varying from 38mm to 44mm. The second vessel was patently non-concentric and the dimensional variation was truly reproduced in the measurements. A third vessel was fabricated with careful control of dimensions and the measurements exhibited good concentricity. Small deviations were observed, attributable to imperfect bondings between steel and lead. This technique has the following advantages: (a) weaker sources used result in less handling problems reducing the personnel exposures considerably; (b) the sensitivity of the instrument is quite good because of better statistics; (c) the time required for scanning a small vessel is more, but a judicious use of a scintillometer for initial fast scan will help in reducing the total scanning time; (d) this method can take advantage of the dimensional variations themselves to get the calibration and to estimate the deviations from specified tolerances. (auth.)

Total contribution of airborne lead to blood lead.

OpenAIRE

Manton, W I

1985-01-01

A nine year study of blood lead concentrations and isotope ratios carried out on a married couple shows that pulmonary deposition cannot account for all the airborne lead in blood; that lead from bone may comprise 70% of blood lead; and that during pregnancy blood lead may double due to mobilisation of lead from bone.

Total contribution of airborne lead to blood lead.

Science.gov (United States)

Manton, W I

1985-01-01

A nine year study of blood lead concentrations and isotope ratios carried out on a married couple shows that pulmonary deposition cannot account for all the airborne lead in blood; that lead from bone may comprise 70% of blood lead; and that during pregnancy blood lead may double due to mobilisation of lead from bone. PMID:3970881

Lead- or Lead-bismuth-cooled fast reactors

International Nuclear Information System (INIS)

Bouchter, J.C.; Courouau, J.L.; Dufour, P.; Guidez, J.; Latge, C.; Martinelli, L.; Renault, C.; Rimpault, G.

2014-01-01

Lead-cooled fast reactors are one of the 6 concepts retained for the 4. generation of nuclear reactors. So far no lead-cooled reactors have existed in the world except lead-bismuth-cooled reactors in soviet submarines. Some problems linked to the use of the lead-bismuth eutectic appeared but were satisfactorily solved by a more rigorous monitoring of the chemistry of the lead-bismuth coolant. Lead presents various advantages as a coolant: no reactivity with water and the air,a high boiling temperature and low contamination when irradiated. The main asset of the lead-bismuth alloy is the drop of the fusion temperature from 327 C degrees to 125 C degrees. The main drawback of using lead (or lead-bismuth) is its high corrosiveness with metals like iron, chromium and nickel. The high corrosiveness of the coolant implies low flow velocities which means a bigger core and consequently a bigger reactor containment. Different research programs in the world (in Europe, Russia and the USA) are reviewed in the article but it appears that the development of this type of reactor requires technological breakthroughs concerning materials and the resistance to corrosion. Furthermore the concept of lead-cooled reactors seems to be associated to a range of low output power because of the compromise between the size of the reactor and its resistance to earthquakes. (A.C.)

Lead in teeth from lead-dosed goats: Microdistribution and relationship to the cumulative lead dose

International Nuclear Information System (INIS)

Bellis, David J.; Hetter, Katherine M.; Jones, Joseph; Amarasiriwardena, Dula; Parsons, Patrick J.

2008-01-01

Teeth are commonly used as a biomarker of long-term lead exposure. There appear to be few data, however, on the content or distribution of lead in teeth where data on specific lead intake (dose) are also available. This study describes the analysis of a convenience sample of teeth from animals that were dosed with lead for other purposes, i.e., a proficiency testing program for blood lead. Lead concentration of whole teeth obtained from 23 animals, as determined by atomic absorption spectrometry, varied from 0.6 to 80 μg g -1 . Linear regression of whole tooth lead (μg g -1 ) on the cumulative lead dose received by the animal (g) yielded a slope of 1.2, with r 2 =0.647 (p -1 , were found in circumpulpal dentine. Linear regression of circumpulpal lead (μg g -1 ) on cumulative lead dose (g) yielded a slope of 23 with r 2 =0.961 (p=0.0001). The data indicated that whole tooth lead, and especially circumpulpal lead, of dosed goats increased linearly with cumulative lead exposure. These data suggest that circumpulpal dentine is a better biomarker of cumulative lead exposure than is whole tooth lead, at least for lead-dosed goats

Analysis of neighborhood behavior in lead optimization and array design.

Science.gov (United States)

Papadatos, George; Cooper, Anthony W J; Kadirkamanathan, Visakan; Macdonald, Simon J F; McLay, Iain M; Pickett, Stephen D; Pritchard, John M; Willett, Peter; Gillet, Valerie J

2009-02-01

Neighborhood behavior describes the extent to which small structural changes defined by a molecular descriptor are likely to lead to small property changes. This study evaluates two methods for the quantification of neighborhood behavior: the optimal diagonal method of Patterson et al. and the optimality criterion method of Horvath and Jeandenans. The methods are evaluated using twelve different types of fingerprint (both 2D and 3D) with screening data derived from several lead optimization projects at GlaxoSmithKline. The principal focus of the work is the design of chemical arrays during lead optimization, and the study hence considers not only biological activity but also important drug properties such as metabolic stability, permeability, and lipophilicity. Evidence is provided to suggest that the optimality criterion method may provide a better quantitative description of neighborhood behavior than the optimal diagonal method.

Evaluation of purity with its uncertainty value in high purity lead stick by conventional and electro-gravimetric methods.

Science.gov (United States)

Singh, Nahar; Singh, Niranjan; Tripathy, S Swarupa; Soni, Daya; Singh, Khem; Gupta, Prabhat K

2013-06-26

A conventional gravimetry and electro-gravimetry study has been carried out for the precise and accurate purity determination of lead (Pb) in high purity lead stick and for preparation of reference standard. Reference materials are standards containing a known amount of an analyte and provide a reference value to determine unknown concentrations or to calibrate analytical instruments. A stock solution of approximate 2 kg has been prepared after dissolving approximate 2 g of Pb stick in 5% ultra pure nitric acid. From the stock solution five replicates of approximate 50 g have been taken for determination of purity by each method. The Pb has been determined as PbSO4 by conventional gravimetry, as PbO2 by electro gravimetry. The percentage purity of the metallic Pb was calculated accordingly from PbSO4 and PbO2. On the basis of experimental observations it has been concluded that by conventional gravimetry and electro-gravimetry the purity of Pb was found to be 99.98 ± 0.24 and 99.97 ± 0.27 g/100 g and on the basis of Pb purity the concentration of reference standard solutions were found to be 1000.88 ± 2.44 and 1000.81 ± 2.68 mg kg-1 respectively with 95% confidence level (k = 2). The uncertainty evaluation has also been carried out in Pb determination following EURACHEM/GUM guidelines. The final analytical results quantifying uncertainty fulfills this requirement and gives a measure of the confidence level of the concerned laboratory. Gravimetry is the most reliable technique in comparison to titremetry and instrumental method and the results of gravimetry are directly traceable to SI unit. Gravimetric analysis, if methods are followed carefully, provides for exceedingly precise analysis. In classical gravimetry the major uncertainties are due to repeatability but in electro-gravimetry several other factors also affect the final results.

Apparatus and methods for monitoring the concentrations of hazardous airborne substances, especially lead

Science.gov (United States)

Zaromb, Solomon

2004-07-13

Air is sampled at a rate in excess of 100 L/min, preferably at 200-300 L/min, so as to collect therefrom a substantial fraction, i.e., at least 20%, preferably 60-100%, of airborne particulates. A substance of interest (analyte), such as lead, is rapidly solubilized from the the collected particulates into a sample of liquid extractant, and the concentration of the analyte in the extractant sample is determined. The high-rate air sampling and particulate collection may be effected with a high-throughput filter cartridge or with a recently developed portable high-throughput liquid-absorption air sampler. Rapid solubilization of lead is achieved by a liquid extractant comprising 0.1-1 M of acetic acid or acetate, preferably at a pH of 5 or less and preferably with inclusion of 1-10% of hydrogen peroxide. Rapid determination of the lead content in the liquid extractant may be effected with a colorimetric or an electroanalytical analyzer.

Symmetric airfoil geometry effects on leading edge noise.

Science.gov (United States)

Gill, James; Zhang, X; Joseph, P

2013-10-01

Computational aeroacoustic methods are applied to the modeling of noise due to interactions between gusts and the leading edge of real symmetric airfoils. Single frequency harmonic gusts are interacted with various airfoil geometries at zero angle of attack. The effects of airfoil thickness and leading edge radius on noise are investigated systematically and independently for the first time, at higher frequencies than previously used in computational methods. Increases in both leading edge radius and thickness are found to reduce the predicted noise. This noise reduction effect becomes greater with increasing frequency and Mach number. The dominant noise reduction mechanism for airfoils with real geometry is found to be related to the leading edge stagnation region. It is shown that accurate leading edge noise predictions can be made when assuming an inviscid meanflow, but that it is not valid to assume a uniform meanflow. Analytic flat plate predictions are found to over-predict the noise due to a NACA 0002 airfoil by up to 3 dB at high frequencies. The accuracy of analytic flat plate solutions can be expected to decrease with increasing airfoil thickness, leading edge radius, gust frequency, and Mach number.

Use of the transpiration method to study polonium evaporation from liquid lead-bismuth eutectic at high temperature

International Nuclear Information System (INIS)

Prieto, Borja Gonzalez; Lim, Jun; Rosseel, Kris; Bosch, Joris van den; Aerts, Alexander; Martens, Johan; Rizzi, Matthias; Neuhausen, Joerg

2014-01-01

Qualitative and quantitative understanding of Po volatilization under different conditions is of key importance for safety assessments of lead-bismuth eutectic (LBE) based nuclear reactors, spallation targets and accelerator driven systems. In this work we explore the possibilities of the transpiration method in combination with simple models to study the equilibrium and kinetics of Po evaporation from highly diluted solutions in lead-bismuth eutectic between 600 and 1000 C in Ar/5% H 2 and Ar. On the basis of evaporation experiments at various carrier gas flow rates, we identified the conditions of vapor saturation allowing the determination of equilibrium constants. From the limiting behavior at high flow rates, values for the maximal evaporation rate of Po from LBE were estimated. Measurements of evaporation as a function of time were consistent with the assumption that polonium dissolved in LBE obeys Henry's law. A theoretical analysis furthermore suggested that diffusion of polonium in LBE was not a rate limiting factor for evaporation under vapor saturation conditions. Newly determined values for the Henry constant of Po in LBE between 600 and 1000 C were consistent with previously derived correlations.

Stable lead isotopes and lake sediments. A useful combination for the study of atmospheric lead pollution history

Energy Technology Data Exchange (ETDEWEB)

Renberg, I.; Braennvall, M.-L.; Bindler, R. [Department of Ecology and Environmental Science, Umea University, SE-901 87 Umea (Sweden); Emteryd, O. [Department of Forest Ecology, Swedish University of Agricultural Sciences, SE-901 83 Umea (Sweden)

2002-06-20

Analysis of stable lead isotopes and lead concentrations in lake-sediment deposits, not least in varved (annually-laminated) sediments, is a useful method to study lead pollution history. This paper presents details from a study of 31 lakes in Sweden. Using a strong acid digestion of sediment samples and ICP-MS analyses, we have found that Swedish lake sediments have a high natural (pre-pollution) 206[Pb]/207[Pb] ratio (mean 1.52{+-}0.18, range 1.28-2.01, n=31 lakes). In contrast, atmospheric lead pollution derived from metal smelting processes, coal burning and from alkyl-lead added to petrol has a lower ratio (<1.2). Consequently, when pollution lead deposition began approximately 3500 years ago, the lead isotope ratio of the sediments started to decline, and in modern sediments it is typically <1.2. Using the isotope and concentration values and a mixing model, the relative contribution of pollution and natural lead in sediment samples can be calculated. The pollution lead records of the Swedish lake sediments show a consistent picture of the atmospheric lead pollution history. Some noticeable features are the Roman peak, the large and permanent Medieval increase, peaks at approximately 1200 and 1530 ad, the rapid increase after World War II, the peak in the 1970s, and the large modern decline.

Determination of 210Pb activity concentration in lead shielding

International Nuclear Information System (INIS)

Slivka, J.; Mrdja, D.; Varga, E.; Veskovic, M.

2005-01-01

210 Pb is concentrated during the separation lead from the ore and therefore it is the main pollutant of lead products. The content of this isotope limits the applicability of lead for low-level shielding of gamma spectrometers. In this paper, a new method for the determination of 210 Pb activity concentration in lead shielding from 46.5 keV gamma line intensity is presented. (author) [sr

COMPARISON OF TWO TEMPERATURE MEASUREMENT METHODS BY UPCONVERSION FLUORESCENCE SPECTRA OF ERBIUM-DOPED LEAD-FLUORIDE NANO-GLASS-CERAMICS

Directory of Open Access Journals (Sweden)

V. A. Aseev

2015-05-01

Full Text Available The study and compare of two temperature measurement methods is performed for the case of a lead-fluoride nano-glassceramics in the range from 317 to 423 K with a view to their application to temperature sensors. A method of temperature measurement by means of violet, green and red upconversion fluorescence spectra regression on latent structures and a method of temperature measurement by two fluorescence bands intensity ratio in green range are considered. It is shown that a four-dimensional space of latent structures is an optimum one in terms of temperature measurement accuracy. It made possible temperature determining with a relative error not larger than 0.15% at temperatures higher than 340 K by making use of fluorescence spectra training set with the step of 10 K. The method using two green bands fluorescence intensity ratio is inferior by the accuracy. Independence of pump power fluctuations is a significant advantage of the second method. To take advantage of the first method a stabilization of the pump power is necessary. The results of the work can be taken into account while developing optical temperature sensors with a better performance (in relation to accuracy and measurement range compared to existing ones which utilize temperature redistribution of fluorescence intensities in two closely-spaced bands or temperature dependence of fluorescence lifetime.

Refinement of the crystal structure of lead titanate with different degrees of imperfection of cationic and anionic sublattices by the Rietveld method

International Nuclear Information System (INIS)

Akimov, A.I.; Savchuk, G.K.; Rubtsov, V.A.; Letko, A.K.

2003-01-01

The parameters of the crystal structure of lead titanate with different degrees of imperfection of the anionic and cationic sublattices are refined by the Rietveld method. The experiments are carried out on a DRON-4 diffractometer (CuK α radiation; 20 deg. d 5.0-6.0%

Leading change: a concept analysis.

Science.gov (United States)

Nelson-Brantley, Heather V; Ford, Debra J

2017-04-01

To report an analysis of the concept of leading change. Nurses have been called to lead change to advance the health of individuals, populations, and systems. Conceptual clarity about leading change in the context of nursing and healthcare systems provides an empirical direction for future research and theory development that can advance the science of leadership studies in nursing. Concept analysis. CINAHL, PubMed, PsycINFO, Psychology and Behavioral Sciences Collection, Health Business Elite and Business Source Premier databases were searched using the terms: leading change, transformation, reform, leadership and change. Literature published in English from 2001 - 2015 in the fields of nursing, medicine, organizational studies, business, education, psychology or sociology were included. Walker and Avant's method was used to identify descriptions, antecedents, consequences and empirical referents of the concept. Model, related and contrary cases were developed. Five defining attributes of leading change were identified: (a) individual and collective leadership; (b) operational support; (c) fostering relationships; (d) organizational learning; and (e) balance. Antecedents were external or internal driving forces and organizational readiness. The consequences of leading change included improved organizational performance and outcomes and new organizational culture and values. A theoretical definition and conceptual model of leading change were developed. Future studies that use and test the model may contribute to the refinement of a middle-range theory to advance nursing leadership research and education. From this, empirically derived interventions that prepare and enable nurses to lead change to advance health may be realized. © 2016 John Wiley & Sons Ltd.

Lead contamination of environment in Meza Valley, Yugoslavia: some considerations on lead content in soil and plants

Energy Technology Data Exchange (ETDEWEB)

Djuric, D; Kerin, Z

1970-01-01

As part of a broad ecological study of lead contamination, soil samples and underground parts of some vegetables were analyzed for lead by the dithizone method. Vegetables fell into three groups: those with a relatively high Pb content (over 30 mg/kg); those with a medium Pb content (over 10 mg/kg); and those with a low Pb content (under 5 mg/kg). Variations in Pb content in the same kind of vegetables represented variations in soil Pb content and absorption. Variations between different kinds of vegetables were due to differences in plant physiology and capacity of absorption, shape and size of root, and depth of root in soil. Lead content was higher in vegetables grown in summer and fall than for the same vegetables grown in spring. Lead absorption coefficients were calculated for underground parts of vegetables according to the relation between the Pb content of the plant and total Pb content of soil and according to the relation between the Pb content of the plant and the AL-soluble Pb in soil (AL is the ammonium lactate acetic acid mixture). The latter method gave much less dispersed coefficients, indicating that AL-soluble Pb represents much more authoritative data for determining absorption coefficients than total soil Pb.

BNL Building 650 lead decontamination and treatment feasibility study. Final report

International Nuclear Information System (INIS)

Kalb, P.D.; Cowgill, M.G.; Milian, L.W.

1995-10-01

Lead has been used extensively at Brookhaven National Laboratory (BNL) for radiation shielding in numerous reactor, accelerator and other research programs. A large inventory of excess lead (estimated at 410,000 kg) in many shapes and sizes is currently being stored. Due to it's toxicity, lead and soluble lead compounds are considered hazardous waste by the Environmental Protection Agency. Through use at BNL, some of the lead has become radioactive, either by contamination of the surface or through activation by neutrons or deuterons. This study was conducted at BNL's Environmental and Waste Technology Center for the BNL Safety and Environmental Protection Division to evaluate feasibility of various treatment options for excess lead currently being stored. The objectives of this effort included investigating potential treatment methods by conducting a review of the literature, developing a means of screening lead waste to determine the radioactive characteristics, examining the feasibility of chemical and physical decontamination technologies, and demonstrating BNL polyethylene macro-encapsulation as a means of treating hazardous or mixed waste lead for disposal. A review and evaluation of the literature indicated that a number of physical and chemical methods are available for decontamination of lead. Many of these techniques have been applied for this purpose with varying degrees of success. Methods that apply mechanical techniques are more appropriate for lead bricks and sheet which contain large smooth surfaces amenable to physical abrasion. Lead wool, turnings, and small irregularly shaped pieces would be treated more effectively by chemical decontamination techniques. Either dry abrasion or wet chemical methods result in production of a secondary mixed waste stream that requires treatment prior to disposal

Efficient scanning of thick lead vessels

International Nuclear Information System (INIS)

Raghunath, V.M.; Bhatnagar, P.K.; Meenakshisundaram, V.

1978-01-01

Lead containers fabricated for transport of radioactive materials need to be evaluated for their shielding integrity. The common method of locating a strong gamma source inside the vessel and scanning the external surface by conventional detectors suffers from high radiation dose and low sensitivity. A new method has been proposed and tried. It is found to be more efficient. In the new method, 60 Co source is loaded at the centre of the lead vessel and the outer surface is scanned by NaI(Tl) detector. The transmitted virgin flux is scanned under the 60 Co channel in a single channel analyser. An area of 25 cm 2 is scanned for 10 to 20 seconds each time. The source strength required is considerably reduced by a factor of 10 or more as compared to the common method and external dose rates do not exceed 50 mR/h (130 nC. kg -1 h -1 ) on the vessel surface. The advantages are improved sensitivity, no interference from scattered radiation and assurance in repeatability of measurements. (M.G.B.)

Absorption and translocation of lead by plants: a contribution to the application of the method of radioactive indicators in the investigation of the change of substance

Energy Technology Data Exchange (ETDEWEB)

Hevesy, G

1923-01-01

The assimilation of lead from lead nitrate solutions by Vicia Faba has been investigated. A radioactive isotope of lead was mixed with the lead nitrate, and the amount of lead taken up was determined after ignition from the radioactive intensity of the ash of the various parts. This method makes possible the determination of exceedingly small amounts of assimilated lead. Whereas 0-3% of the lead is taken up by the root from 200 cc. of a 10/sup -1/ N lead nitrate solution in the course of 24 hours, 60% of the lead content of a 10/sup -1/ N lead nitrate solution in the course of 24 hours, 60% of the lead content of a 10/sup -6/ N solution is taken up in the same time. The leaves show a lead content of only a few hundredths or thousandths of 1% of the amount of lead present in the solution. The assimilated (radioactive) lead can be displaced by introduction of the plant containing lead into another lead solution, whereby inactive lead atoms now take the place of the radioactive ones. From this it follows that the lead is not combined with carbon within the plant, but that it exists in the form of a dissociable salt which is soluble with difficulty. Even after 24 hours, a 10/sup -1/ N solution of a lead salt produces toxic effects on the plant, while more dilute solutions do not. Lead belongs to the least poisonous of the heavy metals. 9 references.

Cumulant generating function formula of heat transfer in ballistic systems with lead-lead coupling and general nonlinear systems

Science.gov (United States)

Li, Huanan

2013-03-01

Based on a two-time observation protocol, we consider heat transfer in a given time interval tM in a lead-junction-lead system taking coupling between the leads into account. In view of the two-time observation, consistency conditions are carefully verified in our specific family of quantum histories. Furthermore, its implication is briefly explored. Then using the nonequilibrium Green's function method, we obtain an exact formula for the cumulant generating function for heat transfer between the two leads, valid in both transient and steady-state regimes. Also, a compact formula for the cumulant generating function in the long-time limit is derived, for which the Gallavotti-Cohen fluctuation symmetry is explicitly verified. In addition, we briefly discuss Di Ventra's repartitioning trick regarding whether the repartitioning procedure of the total Hamiltonian affects the nonequilibrium steady-state current fluctuation. All kinds of properties of nonequilibrium current fluctuations, such as the fluctuation theorem in different time regimes, could be readily given according to these exact formulas. Finally a practical formalism dealing with cumulants of heat transfer across general nonlinear quantum systems is established based on field theoretical/algebraic method.

Update on Recovering Lead From Scrap Batteries

Science.gov (United States)

Cole, E. R.; Lee, A. Y.; Paulson, D. L.

1985-02-01

Previous work at the Bureau of Mines Rolla Research Center, U.S. Department of the Interior, resulted in successful development of a bench-scale, combination electrorefining-electrowinning method for recycling lead from scrap batteries by using waste fluosilicic acid (H2SiF6) as electrolyte.1,2 This paper describes larger scale experiments. Prior attempts to electrowin lead failed because large quantities of insoluble lead dioxide were deposited on the anodes at the expense of lead deposition on the cathodes. A major breakthrough was achieved with the discovery that lead dioxide formation at the anodes is prevented by adding a small amount of phosphorus to the electrolyte. The amount of PbO2 formed on the anodes during lead electrowinning was less than 1% of the total lead deposited on the cathodes. This work recently won the prestigious IR·100 award as one of the 100 most significant technological advances of 1984.

Spectrochemical determination of lead in wines

Directory of Open Access Journals (Sweden)

DRAGAN MARKOVIC

2000-06-01

Full Text Available The determination of lead in wines of different origin was performed by means of atomic emission spectroscopy with argon stabilized DC. U-shaped arc and electrothermal atomic absorption spectrometry. The comparison of the results obtained by the direct and standard addition method has indicated the presence of a depressive effect of the complex organic matrix. The effect is avoided successfully by mineralization, as well as by dissolution of the samples. Thus, a relative simple but precise and sensitive method involving the application of a stabilized arc and photoelectric detection with time integration of the emission signals is recommended for the determination of low concentrations of lead in wines. The complex organic matrix was investigated by recording the IR spectra of different wine fractions.

Determination of temperature dependence of piezoelectric coefficients matrix of lead zirconate titanate ceramics by quasi-static and resonance method

Energy Technology Data Exchange (ETDEWEB)

Li Fei; Xu Zhuo; Wei Xiaoyong; Yao Xi, E-mail: lifei1216@gmail.co [Electronic Materials Research Laboratory, Key Laboratory of the Ministry of Education, Xi' an Jiaotong University, Xi' an 710049 (China)

2009-05-07

The piezoelectric coefficients (d{sub 33}, -d{sub 31}, d{sub 15}, g{sub 33}, -g{sub 31}, g{sub 15}) of soft and hard lead zirconate titanate ceramics were measured by the quasi-static and resonance methods, at temperatures from 20 to 300 {sup 0}C. The results showed that the piezoelectric coefficients d{sub 33}, -d{sub 31} and d{sub 15} obtained by these two methods increased with increasing temperature for both hard and soft PZT ceramics, while the piezoelectric coefficients g{sub 33}, -g{sub 31} and g{sub 15} decreased with increasing temperature for both hard and soft PZT ceramics. In this paper, the observed results were also discussed in terms of intrinsic and extrinsic contributions to piezoelectric response.

Separate base usages of genes located on the leading and lagging strands in Chlamydia muridarum revealed by the Z curve method

Directory of Open Access Journals (Sweden)

Yu Xiu-Juan

2007-10-01

Full Text Available Abstract Background The nucleotide compositional asymmetry between the leading and lagging strands in bacterial genomes has been the subject of intensive study in the past few years. It is interesting to mention that almost all bacterial genomes exhibit the same kind of base asymmetry. This work aims to investigate the strand biases in Chlamydia muridarum genome and show the potential of the Z curve method for quantitatively differentiating genes on the leading and lagging strands. Results The occurrence frequencies of bases of protein-coding genes in C. muridarum genome were analyzed by the Z curve method. It was found that genes located on the two strands of replication have distinct base usages in C. muridarum genome. According to their positions in the 9-D space spanned by the variables u1 – u9 of the Z curve method, K-means clustering algorithm can assign about 94% of genes to the correct strands, which is a few percent higher than those correctly classified by K-means based on the RSCU. The base usage and codon usage analyses show that genes on the leading strand have more G than C and more T than A, particularly at the third codon position. For genes on the lagging strand the biases is reverse. The y component of the Z curves for the complete chromosome sequences show that the excess of G over C and T over A are more remarkable in C. muridarum genome than in other bacterial genomes without separating base and/or codon usages. Furthermore, for the genomes of Borrelia burgdorferi, Treponema pallidum, Chlamydia muridarum and Chlamydia trachomatis, in which distinct base and/or codon usages have been observed, closer phylogenetic distance is found compared with other bacterial genomes. Conclusion The nature of the strand biases of base composition in C. muridarum is similar to that in most other bacterial genomes. However, the base composition asymmetry between the leading and lagging strands in C. muridarum is more significant than that in

Measurement of disintegration rates of small [60Co]Co sources in lead containers by the sum-peak method

International Nuclear Information System (INIS)

Kawano, Takao; Ebihara, Hiroshi

1991-01-01

The sum-peak method has been applied to determine the disintegration rates of two small [ 60 Co]Co sources (30 and 350 kBq) in lead containers with several thickness by using a NaI(Tl) detector. The experimental results showed that the sum-peak method was perfectly effective for the determination of the disintegration rates (unrelated to the thicknesses of the containers) of the 350 kBq source. The sum-peak method was also absolutely effective for the 30 kBq source in the case of containers with thicknesses of 15 mm and less, but in the cases of those with thicknesses of 21, 27 and 33 mm, the disintegration rates were under-estimated and the deviations from the true disintegration rate increased rapidly with increasing thicknesses of the containers. We presume that the under-estimation of the disintegration rates was the result of the over-estimation of the areas under the sum peaks, caused by the interference of the γ-ray (2614 keV) emitted from the naturally occurring radionuclide 208 Tl. (author)

Lead-Related Genetic Loci, Cumulative Lead Exposure and Incident Coronary Heart Disease: The Normative Aging Study

Science.gov (United States)

Weisskopf, Marc G.; Sparrow, David; Schwartz, Joel; Hu, Howard; Park, Sung Kyun

2016-01-01

Background Cumulative exposure to lead is associated with cardiovascular outcomes. Polymorphisms in the δ-aminolevulinic acid dehydratase (ALAD), hemochromatosis (HFE), heme oxygenase-1 (HMOX1), vitamin D receptor (VDR), glutathione S-transferase (GST) supergene family (GSTP1, GSTT1, GSTM1), apolipoprotein E (APOE),angiotensin II receptor-1 (AGTR1) and angiotensinogen (AGT) genes, are believed to alter toxicokinetics and/or toxicodynamics of lead. Objectives We assessed possible effect modification by genetic polymorphisms in ALAD, HFE, HMOX1, VDR, GSTP1, GSTT1, GSTM1, APOE, AGTR1 and AGT individually and as the genetic risk score (GRS) on the association between cumulative lead exposure and incident coronary heart disease (CHD) events. Methods We used K-shell-X-ray fluorescence to measure bone lead levels. GRS was calculated on the basis of 22 lead-related loci. We constructed Cox proportional hazard models to compute adjusted hazard ratios (HRs) and 95% confidence intervals (CIs) for incident CHD. We applied inverse probability weighting to account for potential selection bias due to recruitment into the bone lead sub-study. Results Significant effect modification was found by VDR, HMOX1, GSTP1, APOE, and AGT genetic polymorphisms when evaluated individually. Further, the bone lead-CHD associations became larger as GRS increases. After adjusting for potential confounders, a HR of CHD was 2.27 (95%CI: 1.50–3.42) with 2-fold increase in patella lead levels, among participants in the top tertile of GRS. We also detected an increasing trend in HRs across tertiles of GRS (p-trend = 0.0063). Conclusions Our findings suggest that lead-related loci as a whole may play an important role in susceptibility to lead-related CHD risk. These findings need to be validated in a separate cohort containing bone lead, lead-related genetic loci and incident CHD data. PMID:27584680

Ferroelectric lead magnesium niobate-lead titanate single crystals for ultrasonic hydrophone applications

International Nuclear Information System (INIS)

Lau, S.T.; Lam, K.H.; Chan, H.L.W.; Choy, C.L.; Luo, H.S.; Yin, Q.R.; Yin, Z.W.

2004-01-01

Ferroelectric lead magnesium niobate-lead titanate (PMN-PT) single crystals with a composition around the rhombohedral-tetragonal morphotropic phase boundary (65 mol% of PMN) were used to fabricate single-element needle-type hydrophones for measuring the spatial and temporal characteristics of medical ultrasonic transducers. PMN-PT single crystal was grown by a modified Bridgman method. Discs (0.5 mm thick) with normal along the direction were cut and then poled by a dc field in the thickness direction. The single crystal has a high relative permittivity (ε r ∼4000) making it appropriate for small area hydrophone applications. Single-element needle-type hydrophones with this material as the sensing element have been fabricated and characterized. The hydrophones have flat frequency response and good receiving sensitivity over certain frequency range in the megahertz region

The Pollution Detectives, Part III: Roadside Lead Pollution.

Science.gov (United States)

Sanderson, Phil

1989-01-01

Described is a simple test tube method developed lead analysis of samples of roadside soil. The relationship between the results and the traffic flow indicate car exhausts are the major source of lead pollution. Materials and procedures are detailed. An example of results is provided. (Author/CW)

Control and monitoring of oxygen content in molten metals. Application to lead and lead-bismuth melts

International Nuclear Information System (INIS)

Ghetta, V.; Fouletier, J.; Henault, M.; Le Moulec, A.

2002-01-01

The sources of error in potentiometric measurements of the oxygen activity in molten metals and the methods proposed to reduce these measurements errors are described. Specific constraints related to low temperature measurements are emphasized. Two set-ups for control of the oxygen activity in molten lead and lead-bismuth were developed. They involve zirconia-based cells, i.e., an oxygen pump and an oxygen probe. The performance of the set-ups was characterized attempts to reduce the working temperature (T<450 deg C) are discussed. (authors)

Accuracy of measuring half- and quarter-value layers and appropriate aperture width of a convenient method using a lead-covered case in X-ray computed tomography.

Science.gov (United States)

Matsubara, Kosuke; Ichikawa, Katsuhiro; Murasaki, Yuichi; Hirosawa, Ayaka; Koshida, Kichiro

2014-01-06

Determination of the half-value layer (HVL) and quarter-value layer (QVL) values is not an easy task in x-ray computed tomography (CT), because a nonrotating x-ray tube must be used, which requires the assistance of service engineers. Therefore, in this study, we determined the accuracy of the lead-covered case method, which uses x-rays from a rotating x-ray tube, for measuring the HVL and QVL in CT. The lead-covered case was manufactured from polystyrene foam and a 4-mm thick lead plate. The ionizing chamber was placed in the center of the case, and aluminum filters were placed 15 cm above the aperture surface. Aperture widths of 1.0, 2.0, and 3.0 cm for a tube voltage of 110 kV and an aperture width of 2.0 cm for the tube voltages of 80 and 130 kV were used to measure exposure doses. The results of the HVL and QVL were compared with those of the conventional nonrotating method. A 2.0-cm aperture was believed to be adequate, because of its small differences in the HVL and QVL in the nonrotating method and its reasonable exposure dose level. When the 2.0-cm aperture was used, the lead-covered case method demonstrated slightly larger HVLs and QVLs (0.03-0.06 mm for the HVL and 0.2-0.4 mm for the QVL) at all the tube voltage settings. However, the differences in the effective energy were 0.1-0.3 keV; therefore, it could be negligible in an organ-absorbed dose evaluation and a quality assurance test for CT.

Identification of sources of lead exposure in French children by lead isotope analysis: a cross-sectional study

Directory of Open Access Journals (Sweden)

Lucas Jean-Paul

2011-08-01

Full Text Available Abstract Background The amount of lead in the environment has decreased significantly in recent years, and so did exposure. However, there is no known safe exposure level and, therefore, the exposure of children to lead, although low, remains a major public health issue. With the lower levels of exposure, it is becoming more difficult to identify lead sources and new approaches may be required for preventive action. This study assessed the usefulness of lead isotope ratios for identifying sources of lead using data from a nationwide sample of French children aged from six months to six years with blood lead levels ≥25 μg/L. Methods Blood samples were taken from 125 children, representing about 600,000 French children; environmental samples were taken from their homes and personal information was collected. Lead isotope ratios were determined using quadrupole ICP-MS (inductively coupled plasma - mass spectrometry and the isotopic signatures of potential sources of exposure were matched with those of blood in order to identify the most likely sources. Results In addition to the interpretation of lead concentrations, lead isotope ratios were potentially of use for 57% of children aged from six months to six years with blood lead level ≥ 25 μg/L (7% of overall children in France, about 332,000 children, with at least one potential source of lead and sufficiently well discriminated lead isotope ratios. Lead isotope ratios revealed a single suspected source of exposure for 32% of the subjects and were able to eliminate at least one unlikely source of exposure for 30% of the children. Conclusions In France, lead isotope ratios could provide valuable additional information in about a third of routine environmental investigations.

Evolution of spin-dependent structure functions from DGLAP equations in leading order and next to leading order

International Nuclear Information System (INIS)

Baishya, R.; Jamil, U.; Sarma, J. K.

2009-01-01

In this paper the spin-dependent singlet and nonsinglet structure functions have been obtained by solving Dokshitzer, Gribov, Lipatov, Altarelli, Parisi evolution equations in leading order and next to leading order in the small x limit. Here we have used Taylor series expansion and then the method of characteristics to solve the evolution equations. We have also calculated t and x evolutions of deuteron structure functions, and the results are compared with the SLAC E-143 Collaboration data.

Study by lead isotope method of a vein : Sobrado of the Boquira mine (Bahia State, Brazil)

International Nuclear Information System (INIS)

Cassedanne, J.P.; Duthou, J.-L.; Clermont-Ferrand Univ., 63

1981-01-01

Fourteen samples of galena from the Sobrado vein, Boquira mine (Bahia) are analysed. Lead isotope compositions show an irregular variation from the central part to the extremidades. They are the result of a mixture of lead from normal galenas and lead which aparent U/Pb ratio are higher. (ARHC) [pt

Lead poisoning

Energy Technology Data Exchange (ETDEWEB)

Beijers, J A

1952-01-01

Three cases of acute lead poisoning of cattle herds via ingestion are reported, and reference is made to several other incidents of lead in both humans and animals. The quantity of lead which was found in the livers of the dead cows varied from 6.5 to 19 mg/kg, while 1160 mg/kg of lead in the liver was found for a young cow which was poisoned experimentally with 5 gms of lead acetate per day; hence, there appears to be great variability in the amounts deposited that can lead to intoxication and death. No evidence was found for a lead seam around the teeth, prophyrinuria, or basophil granules in the erythrocytes during acute or chronic lead poisoning of cattle or horses examined. Reference is made to attempts of finding the boundary line between increased lead absorption and lead intoxication in humans, and an examination of 60 laborers in an offset-printing office containing a great deal of inhalable lead (0.16 to 1.9 mg/cu m air) is reviewed. Physical deviation, basophylic granulation of erythrocytes, increased lead content of the urine, and porphyrinuria only indicate an increased absorption of lead; the use of the term intoxication is justified if, in addition, there are complaints of lack of appetite, constipation, fatigue, abdominal pain, and emaciation.

An experimental design method leading to chemical Turing patterns.

Science.gov (United States)

Horváth, Judit; Szalai, István; De Kepper, Patrick

2009-05-08

Chemical reaction-diffusion patterns often serve as prototypes for pattern formation in living systems, but only two isothermal single-phase reaction systems have produced sustained stationary reaction-diffusion patterns so far. We designed an experimental method to search for additional systems on the basis of three steps: (i) generate spatial bistability by operating autoactivated reactions in open spatial reactors; (ii) use an independent negative-feedback species to produce spatiotemporal oscillations; and (iii) induce a space-scale separation of the activatory and inhibitory processes with a low-mobility complexing agent. We successfully applied this method to a hydrogen-ion autoactivated reaction, the thiourea-iodate-sulfite (TuIS) reaction, and noticeably produced stationary hexagonal arrays of spots and parallel stripes of pH patterns attributed to a Turing bifurcation. This method could be extended to biochemical reactions.

Supported Lead in Pb-210 Chronology

Energy Technology Data Exchange (ETDEWEB)

Pittauerova, D.; Hettwig, B.; Fischer, H. W. [Institute of Environmental Physics, University of Bremen, Bremen (Germany)

2013-07-15

A widely applied method of supported lead estimation in sediments using gamma spectrometric {sup 226}Ra determination via {sup 222}Rn short lived daughter products relies on radioactive equilibrium between {sup 226}Ra and {sup 222}Rn being established after sealing the samples. Advantages and disadvantages of methods of {sup 226}Ra estimation in sediments, using either {sup 222}Rn daughter products or direct estimation by 186.2 keV gamma emissions are discussed. An equilibrium experiment was performed using test samples and in one case radioactive equilibrium was not reached. On a theoretical sediment profile it was shown how systematic errors in supported {sup 210}Pb estimation can lead to incorrect interpretations of {sup 210}Pb{sub xs} profiles and therefore affect {sup 210}Pb derived chronologies. (author)

Ion exchange separation of lead from strontium in certified reference samples and spectrophotometric determination of lead as extractable ion-pair of eosin2- and the lead-cryptand (2.2.2)2+ complex

International Nuclear Information System (INIS)

Al-Merey, R.; Al-Shayah, O.

2004-01-01

A two-step procedure including anion exchange separation of lead from strontium in geological reference samples and a spectrophotometric determination of the separated lead as lead-cryptate (2.2.2) complex is presented. The exchangeable anion Cl - of the ion exchange resin (Dowex 1x4) is changed to Br - in 6M HBr solution. Lead is quantitatively retained in the column from 0.5M HBr medium, while Sr 2+ , Ba 2+ , Ca 2+ , Mg 2+ , Na + , K + , Fe 3+ , Cr 3+ , and Al 3+ are passed through. Subsequently the retained Ph is eluted from the column with 6M HBr. The separation efficiency of the resin is controlled using mixed standard solution of (Pb, Sr, Ca, Mg, Ba, Na, K, Fe, Cr and Al), and radioactive tracer of 85 Sr and 131 Ba. The resin selectivity coefficient (K) of separating Pb from Sr is found to be K S r P b∼10 9 . The Spectrophotometric method of lead determination is based on the formation of lead-crytate (2.2.2) complex at pH 8.3 using borate/HCl as a buffer solution. Then the ion-pair of eosin 2+ and lead-cryptand (2.2.2) complex is extracted with chloroform, finally the absorbance of the extractable legend is measured at 550 nm. The extraction recovery, accuracy, precision, linearity and detection limit of the spectrophotometric method are 99.58%, 1.7%, 0.080μg mL -1 , o-9μg mL -1 , and 0.060μg mL -1 , respectively. (author)

Automated method for simultaneous lead and strontium isotopic analysis applied to rainwater samples and airborne particulate filters (PM10).

Science.gov (United States)

Beltrán, Blanca; Avivar, Jessica; Mola, Montserrat; Ferrer, Laura; Cerdà, Víctor; Leal, Luz O

2013-09-03

A new automated, sensitive, and fast system for the simultaneous online isolation and preconcentration of lead and strontium by sorption on a microcolumn packed with Sr-resin using an inductively coupled plasma mass spectrometry (ICP-MS) detector was developed, hyphenating lab-on-valve (LOV) and multisyringe flow injection analysis (MSFIA). Pb and Sr are directly retained on the sorbent column and eluted with a solution of 0.05 mol L(-1) ammonium oxalate. The detection limits achieved were 0.04 ng for lead and 0.03 ng for strontium. Mass calibration curves were used since the proposed system allows the use of different sample volumes for preconcentration. Mass linear working ranges were between 0.13 and 50 ng and 0.1 and 50 ng for lead and strontium, respectively. The repeatability of the method, expressed as RSD, was 2.1% and 2.7% for Pb and Sr, respectively. Environmental samples such as rainwater and airborne particulate (PM10) filters as well as a certified reference material SLRS-4 (river water) were satisfactorily analyzed obtaining recoveries between 90 and 110% for both elements. The main features of the LOV-MSFIA-ICP-MS system proposed are the capability to renew solid phase extraction at will in a fully automated way, the remarkable stability of the column which can be reused up to 160 times, and the potential to perform isotopic analysis.

[Unification of methods for determining the trace quantities of lead, zinc, sodium and potassium ions in the assessment of drinking water adn transfusion fluid quality].

Science.gov (United States)

Popkov, V A; Golovina, N V; Evgrafov, A A

2001-01-01

The results of long-term studies made by the Department of General Chemistry, I. M. Sechenov Moscow Medical Academy, that deals with unification of methods for determining some ions of metals (lead, zinc, sodium, and potassium) in the assessment of the quality of drinking water and transfusion fluids are summarized. A procedure was developed to determine the trace impurities of zinc, lead, and silver by atomic absorption spectrometry (AAS) by using sorption concentration. C-80-2-aminothiazole, a new sorbent synthesized at the Research Institute of Polymers, was used to detect these ions in the drinking water. With regards to the chosen optimal conditions, drinking water samples were analyzed via their direct spraying in the air-acetylene flame. The prior sorption concentration determined drinking water zinc and lead ions in the concentrations equal to or less than their permissible dose concentrations. The studies indicated that the used methods to determine the trace quantities of metals in the drinking water and aqueous solutions show a high sensitivity, rapidity, simplicity of sample preparation.

Optimum input leads for cryogenic apparatus

International Nuclear Information System (INIS)

Der Nigohossian, G.

1967-02-01

The electrical leads used to introduce a current into a cryostat cause a heat influx due to thermal conduction and to Joule heating. It is very important to be able to minimize this flux. Theoretical calculation of optimized leads takes into account the varying heat and electrical conductivities of the leads as well as the heat exchange coefficient with the effluent gas. Practical results have been summarized in different tables which permit for a specific material i.e. copper, aluminium, brass, stainless steel with the intensity and end temperatures being known (i.e. 4,2 or 18,5 deg. K at the cold end; 77,295 or 320 deg. K at the warm end) to deduce the minimum heat flow and the length-cross section ratio of the optimized leads. A general method is indicated, which would allow to solve the same problem for other materials. (author) [fr

Biosorption of lead phosphates by lead-tolerant bacteria as a mechanism for lead immobilization.

Science.gov (United States)

Rodríguez-Sánchez, Viridiana; Guzmán-Moreno, Jesús; Rodríguez-González, Vicente; Flores-de la Torre, Juan Armando; Ramírez-Santoyo, Rosa María; Vidales-Rodríguez, Luz Elena

2017-08-01

The study of metal-tolerant bacteria is important for bioremediation of contaminated environments and development of green technologies for material synthesis due to their potential to transform toxic metal ions into less toxic compounds by mechanisms such as reduction, oxidation and/or sequestration. In this study, we report the isolation of seven lead-tolerant bacteria from a metal-contaminated site at Zacatecas, México. The bacteria were identified as members of the Staphylococcus and Bacillus genera by microscopic, biochemical and 16S rDNA analyses. Minimal inhibitory concentration of these isolates was established between 4.5 and 7.0 mM of Pb(NO 3 ) 2 in solid and 1.0-4.0 mM of Pb(NO 3 ) 2 in liquid media. A quantitative analysis of the lead associated to bacterial biomass in growing cultures, revealed that the percentage of lead associated to biomass was between 1 and 37% in the PbT isolates. A mechanism of complexation/biosorption of lead ions as inorganic phosphates (lead hydroxyapatite and pyromorphite) in bacterial biomass, was determined by Fourier transform infrared spectroscopy and X-ray diffraction analyses. Thus, the ability of the lead-tolerant isolates to transform lead ions into stable and highly insoluble lead minerals make them potentially useful for immobilization of lead in mining waste.

An Examination of Blood Lead Levels in Thai Nielloware Workers

OpenAIRE

Decharat, Somsiri; Kongtip, Pornpimol; Thampoophasiam, Prapin; Thetkathuek, Anamai

2012-01-01

Objectives: The objectives of this study were to determine the lead levels in blood samples from nielloware workers, to determine airborne lead levels, to describe the workers’ hygiene behaviors, and to ascertain and describe any correlations between lead levels in blood samples and lead levels in airborne samples. Methods: Blood samples and airborne samples from 45 nielloware workers were collected from nielloware workplaces in Nakhon Sri Thammarat Province, Thailand. Lead levels were det...

A simplified in-situ electrochemical decontamination of lead from polluted soil (abstract)

International Nuclear Information System (INIS)

Ansari, T.M.; Ahmad, I.; Khan, Q.M.; Chaudhry, A.H.

2011-01-01

This paper reports a simplified In-Situ electrochemical method for remediation of field soil contaminated with lead. A series of electrochemical decontamination experiments including variable conditions such as operating duration and application of enhancement reagent were performed to demonstrate the efficiency of lead removal from spiked and polluted soil samples collected from Lahore, Pakistan. The results showed that the efficiency of lead removal from the contaminated soil increased with increasing the operating duration under a set of experimental conditions. The reagent used as complexing and solubilizing agent i.e. EDTA was found to be efficient in removing lead from the polluted soil. After 15 days duration, 85 % lead removal efficiency was observed in spiked soil under enhanced conditions , however, 63 % lead removal was achieved from the polluted soil samples by the simplified In-situ electrochemical decontamination method. The method is simple, rapid, cheaper and suitable for soil remediation purposes. (author)

Treating Lead Toxicity: Possibilities beyond Synthetic Chelation

Directory of Open Access Journals (Sweden)

Shambhavi Tannir

2013-01-01

Full Text Available Lead, a ubiquitous metal, is one of the most abundant elements present on earth. Its easy availability and cost effectiveness made it an extremely popular component in the industrial revolution. However, its hazardous health effects were not considered at the time. Over the last few decades, with the adverse effects of lead coming to the forefront, nations across the world have started to recognize and treat lead toxicity. The most reliable and used method until now has been chelation therapy. Recent research has suggested the use of natural products and sources to treat lead poisoning with minimal or no side effects. This review has tried to summarize a few of the natural products/sources being investigated by various groups.

Arctic lead detection using a waveform mixture algorithm from CryoSat-2 data

Science.gov (United States)

Lee, Sanggyun; Kim, Hyun-cheol; Im, Jungho

2018-05-01

We propose a waveform mixture algorithm to detect leads from CryoSat-2 data, which is novel and different from the existing threshold-based lead detection methods. The waveform mixture algorithm adopts the concept of spectral mixture analysis, which is widely used in the field of hyperspectral image analysis. This lead detection method was evaluated with high-resolution (250 m) MODIS images and showed comparable and promising performance in detecting leads when compared to the previous methods. The robustness of the proposed approach also lies in the fact that it does not require the rescaling of parameters (i.e., stack standard deviation, stack skewness, stack kurtosis, pulse peakiness, and backscatter σ0), as it directly uses L1B waveform data, unlike the existing threshold-based methods. Monthly lead fraction maps were produced by the waveform mixture algorithm, which shows interannual variability of recent sea ice cover during 2011-2016, excluding the summer season (i.e., June to September). We also compared the lead fraction maps to other lead fraction maps generated from previously published data sets, resulting in similar spatiotemporal patterns.

[Lead poisoning: towards a paleo-epidemiologic re-interpretation?].

Science.gov (United States)

Bourdieu, Anne

2014-01-01

Lead is a major public health issue. Its use has been increasing since Neolithic times, climaxing in the Ancient Rome and the nineteenth century. Defining the frequency of plumbism before modern times proves to be a difficult matter because of its various and delayed symptoms, and of diagenetic processes affecting bones. After reviewing various methods of lead measurement in bone and tooth, we will expose ways to ascertain lead measurement interpretation in order to estimate the epidemiology of plumbism in ancient times.

The Analysis on Leading industries in Central Java Province

Directory of Open Access Journals (Sweden)

Setyani Irmawati

2016-06-01

Full Text Available The purpose of this research is for identifying the types of industriesthat become leading industries in Central Java Province. The methods, used are LQ (SLQ and DLQ and Shift Share. The result of this research shows that the the leading industries in Central Java Province are beverage industry, tobacco processing industry, textile industry, apparel industry, wood industry, printing industry, furniture industry and other processing industries.In the future, the development of the industry should not only focus on the leading industries  but also onnon-leading industries, so that the non leading industries will not be left behind.

First detection of lead in black paper from intraoral film

International Nuclear Information System (INIS)

Guedes, Debora F.C.; Silva, Reginaldo S.; Veiga, Marcia A.M.S. da; Pecora, Jesus D.

2009-01-01

Lead (Pb) contamination in the black paper that recovers intraoral films (BKP) has been investigated. BKP samples were collected from the Radiology Clinics of the Dental School of Ribeirao Preto, University of Sao Paulo, Brazil. For sake of comparison, four different methods were used. The results revealed the presence of high lead levels, well above the maximum limit allowed by the legislation. Pb contamination levels achieved after the following treatments: paper digestion in nitric acid, microwave treatment, DIN38414-54 method and TCLP method were 997 μg g -1 , 189 μg g -1 , 20.8 μg g -1 , and 54.0 μg g -1 , respectively. Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma mass spectrometry (ICP-MS) were employed for lead determination according to the protocols of the applied methods. Lead contamination in used BKP was confirmed by scanning electron microscopy coupled with energy dispersive X-ray microanalysis (SEM-EDS). All the SEM imaging was carried out in the secondary electron mode (SE) and backscattered-electron mode (QBSD) following punctual X-ray fluorescence spectra. Soil contamination derived from this product revealed the urgent need of addressing this problem. These elevated Pb levels, show that a preliminary treatment of BKP is mandatory before it is disposed into the common trash. The high lead content of this material makes its direct dumping into the environment unwise.

A comparison of portable XRF and ICP-OES analysis for lead on air filter samples from a lead ore concentrator mill and a lead-acid battery recycler.

Science.gov (United States)

Harper, Martin; Pacolay, Bruce; Hintz, Patrick; Andrew, Michael E

2006-03-01

Personal and area samples for airborne lead were taken at a lead mine concentrator mill, and at a lead-acid battery recycler. Lead is mined as its sulfidic ore, galena, which is often associated with zinc and silver. The ore typically is concentrated, and partially separated, on site by crushing and differential froth flotation of the ore minerals before being sent to a primary smelter. Besides lead, zinc and iron are also present in the airborne dusts, together with insignificant levels of copper and silver, and, in one area, manganese. The disposal of used lead-acid batteries presents environmental issues, and is also a waste of recoverable materials. Recycling operations allow for the recovery of lead, which can then be sold back to battery manufacturers to form a closed loop. At the recycling facility lead is the chief airborne metal, together with minor antimony and tin, but several other metals are generally present in much smaller quantities, including copper, chromium, manganese and cadmium. Samplers used in these studies included the closed-face 37 mm filter cassette (the current US standard method for lead sampling), the 37 mm GSP or "cone" sampler, the 25 mm Institute of Occupational Medicine (IOM) inhalable sampler, the 25 mm Button sampler, and the open-face 25 mm cassette. Mixed cellulose-ester filters were used in all samplers. The filters were analyzed after sampling for their content of the various metals, particularly lead, that could be analyzed by the specific portable X-ray fluorescence (XRF) analyzer under study, and then were extracted with acid and analyzed by inductively coupled plasma optical emission spectroscopy (ICP-OES). The 25 mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37 mm filters. For lead at the mine concentrate mill, all five samplers gave good correlations (r2 > 0.96) between the two analytical methods over the entire range of found lead mass

Mechanochemical synthesis of nanocrystalline lead selenide. Industrial approach

Energy Technology Data Exchange (ETDEWEB)

Achimovicova, Marcela; Balaz, Peter [Slovak Academy of Sciences, Kosice (Slovakia). Inst. of Geotechnics; Durisin, Juraj [Slovak Academy of Sciences, Kosice (Slovakia). Inst. of Materials Research; Daneu, Nina [Josef Stefan Institute, Ljubljana (Slovenia). Dept. for Nanostructured Materials; Kovac, Juraj; Satka, Alexander [Slovak Univ. of Technology and International Laser Centre, Bratislava (Slovakia). Dept. of Microelectronics; Feldhoff, Armin [Leibniz Univ. Hannover (Germany). Inst. fuer Physikalische Chemie und Elektrochemie; Gock, Eberhard [Technical Univ. Clausthal, Clausthal-Zellerfeld (Germany). Inst. of Mineral and Waste Processing and Dumping Technology

2011-04-15

Mechanochemical synthesis of lead selenide PbSe nanoparticles was performed by high-energy milling of lead and selenium powder in a laboratory planetary ball mill and in an industrial eccentric vibratory mill. Structural properties of the synthesized lead selenide were characterized using X-ray diffraction that confirmed crystalline nature of PbSe nanoparticles. The average size of PbSe crystallites of 37 nm was calculated from X-ray diffraction data using the Williamson-Hall method. The methods of particle size distribution analysis, specific surface area measurement, scanning electron microscopy and transmission electron microscopy were used for characterization of surface, mean particle size, and morphology of PbSe. An application of industrial mill verified a possibility of the synthesis of a narrow bandgap semiconductor PbSe at ambient temperature and in a relatively short reaction time. (orig.)

X-ray protective clothing. Does DIN 6857-1 allow an objective comparison between lead-free and lead-composite materials?

International Nuclear Information System (INIS)

Eder, H.; Schlattl, H.; Hoeschen, C.

2010-01-01

Purpose: The validity of DIN 6857-1 to establish lead equivalence for protective clothing is evaluated by Monte Carlo simulations and measurements. Materials and Methods: Commercially available protective clothing made of lead, lead-free and lead-composite materials has been tested regarding its protective efficacy. The analysis has been performed on the one hand in accordance with the test conditions described in the manufacturing standard DIN EN 61331-3 and on the other hand following the new DIN 6857-1 standard. Additionally, measurements have been carried out under simulated patient conditions by using an Alderson-Rando phantom. Results: Following DIN EN 61331-3, the lead-free protective clothing achieved the required protective efficacy only at a restricted tube-voltage range. The test according to DIN 6857-1 showed that the protective criteria were fulfilled only by one lead-composite apron, but not by the three lead-free aprons examined. Thus, in order to guarantee the same protection as lead between 50 and 120 kV, the conditions of DIN 6857-1 must be fulfilled. Conclusion: A modification of DIN EN 61331-3 to account for secondary radiation is strongly advised in the case of lead-free materials. In summary, most of the protective lead-free aprons in use should be used with care, particularly for examinations with a high dose. (orig.)

QCD event generators with next-to-leading order matrix-elements and parton showers

International Nuclear Information System (INIS)

Kurihara, Y.; Fujimoto, J.; Ishikawa, T.; Kato, K.; Kawabata, S.; Munehisa, T.; Tanaka, H.

2003-01-01

A new method to construct event-generators based on next-to-leading order QCD matrix-elements and leading-logarithmic parton showers is proposed. Matrix elements of loop diagram as well as those of a tree level can be generated using an automatic system. A soft/collinear singularity is treated using a leading-log subtraction method. Higher order resummation of the soft/collinear correction by the parton shower method is combined with the NLO matrix-element without any double-counting in this method. An example of the event generator for Drell-Yan process is given for demonstrating a validity of this method

Investigation and Evaluation of Children’s Blood Lead Levels around a Lead Battery Factory and Influencing Factors

Directory of Open Access Journals (Sweden)

Feng Zhang

2016-05-01

Full Text Available Lead pollution incidents have occurred frequently in mainland China, which has caused many lead poisoning incidents. This paper took a battery recycling factory as the subject, and focused on measuring the blood lead levels of environmental samples and all the children living around the factory, and analyzed the relationship between them. We collected blood samples from the surrounding residential area, as well as soil, water, vegetables. The atomic absorption method was applied to measure the lead content in these samples. The basic information of the generation procedure, operation type, habit and personal protect equipment was collected by an occupational hygiene investigation. Blood lead levels in 43.12% of the subjects exceeded 100 μg/L. The 50th and the 95th percentiles were 89 μg/L and 232 μg/L for blood lead levels in children, respectively, and the geometric mean was 94 μg/L. Children were stratified into groups by age, gender, parents’ occupation, distance and direction from the recycling plant. The difference of blood lead levels between groups was significant (p < 0.05. Four risk factors for elevated blood lead levels were found by logistic regression analysis, including younger age, male, shorter distance from the recycling plant, and parents with at least one working in the recycling plant. The rate of excess lead concentration in water was 6.25%, 6.06% in soil and 44.44% in leaf vegetables, which were all higher than the Chinese environment standards. The shorter the distance to the factory, the higher the value of BLL and lead levels in vegetable and environment samples. The lead level in the environmental samples was higher downwind of the recycling plant.

Localized accumulation of lead within and among bones from lead-dosed goats

International Nuclear Information System (INIS)

Cretacci, Yan; Parsons, Patrick J.

2010-01-01

The principal aim of this study was to gain a better understanding of where lead (Pb) accumulates and how it is distributed, within the bones of dosed goats. Adult goats were periodically dosed with Pb over a number of years for the primary purpose of producing blood pools containing endogenously bound Pb, for the New York State Blood Lead Proficiency Testing Program. Bone samples (e.g., primarily tibia, femur, humerus, and radius) were collected post-mortem from 11 animals and were analyzed for Pb content by acid digestion and electrothermal atomic absorption spectrometry (ETAAS or GFAAS). Average tibia Pb levels were found to correlate strongly with the cumulative Pb dose (r 2 =0.81). However, the concentration of Pb in different bones and even within a small area of the same bone varied tremendously. Blood-rich trabecular (spongy) bone, such as the patella and calcaneus, were much more enriched in Pb than was cortical (compact) bone. In some dosed animals, the Pb concentration in the tibia was markedly higher at the proximal and distal ends of the bone compared to the mid-shaft. The implications of these findings with regard to the noninvasive measurement of lead in bone by XRF methods are discussed.

Localized accumulation of lead within and among bones from lead-dosed goats

Energy Technology Data Exchange (ETDEWEB)

Cretacci, Yan [Laboratory of Inorganic and Nuclear Chemistry, Wadsworth Center, New York State Department of Health, P.O. Box 509, Albany, NY 12201-0509 (United States); Department of Environmental Health Sciences, School of Public Health, The University at Albany, P.O. Box 509, Albany, NY 12201-0509 (United States); Parsons, Patrick J., E-mail: pparsons@wadsworth.org [Laboratory of Inorganic and Nuclear Chemistry, Wadsworth Center, New York State Department of Health, P.O. Box 509, Albany, NY 12201-0509 (United States); Department of Environmental Health Sciences, School of Public Health, The University at Albany, P.O. Box 509, Albany, NY 12201-0509 (United States)

2010-01-15

The principal aim of this study was to gain a better understanding of where lead (Pb) accumulates and how it is distributed, within the bones of dosed goats. Adult goats were periodically dosed with Pb over a number of years for the primary purpose of producing blood pools containing endogenously bound Pb, for the New York State Blood Lead Proficiency Testing Program. Bone samples (e.g., primarily tibia, femur, humerus, and radius) were collected post-mortem from 11 animals and were analyzed for Pb content by acid digestion and electrothermal atomic absorption spectrometry (ETAAS or GFAAS). Average tibia Pb levels were found to correlate strongly with the cumulative Pb dose (r{sup 2}=0.81). However, the concentration of Pb in different bones and even within a small area of the same bone varied tremendously. Blood-rich trabecular (spongy) bone, such as the patella and calcaneus, were much more enriched in Pb than was cortical (compact) bone. In some dosed animals, the Pb concentration in the tibia was markedly higher at the proximal and distal ends of the bone compared to the mid-shaft. The implications of these findings with regard to the noninvasive measurement of lead in bone by XRF methods are discussed.

Arctic lead detection using a waveform mixture algorithm from CryoSat-2 data

Directory of Open Access Journals (Sweden)

S. Lee

2018-05-01

Full Text Available We propose a waveform mixture algorithm to detect leads from CryoSat-2 data, which is novel and different from the existing threshold-based lead detection methods. The waveform mixture algorithm adopts the concept of spectral mixture analysis, which is widely used in the field of hyperspectral image analysis. This lead detection method was evaluated with high-resolution (250 m MODIS images and showed comparable and promising performance in detecting leads when compared to the previous methods. The robustness of the proposed approach also lies in the fact that it does not require the rescaling of parameters (i.e., stack standard deviation, stack skewness, stack kurtosis, pulse peakiness, and backscatter σ0, as it directly uses L1B waveform data, unlike the existing threshold-based methods. Monthly lead fraction maps were produced by the waveform mixture algorithm, which shows interannual variability of recent sea ice cover during 2011–2016, excluding the summer season (i.e., June to September. We also compared the lead fraction maps to other lead fraction maps generated from previously published data sets, resulting in similar spatiotemporal patterns.

Stable lead isotopes in environmental health with emphasis on human investigations

International Nuclear Information System (INIS)

Gulson, Brian

2008-01-01

There has been widespread use of stable lead isotopes in the earth sciences for more than 40 years focussed on the origin and age of rocks and minerals with lesser application in environmental investigations where the emphasis has been directed typically to the source of lead in environmental media such as air, water and soils. In contrast, the number of environmental health investigations focussed on humans (and primates) is limited in spite of the demonstrated utility of the approach in pioneering studies in the early 1970's. This paper reviews the status of lead isotopes in human investigations especially over the past 2 decades, the period over which most activity has taken place. Following a brief introduction to the method, examples are provided illustrating the use of lead isotopes in a wide spectrum of activities including sources and pathways of lead in diverse environments from urban to mining communities, various applications associated with pregnancy, the contribution of bone lead to blood lead including in the elderly, the half-life of lead in blood, and lead in bones and other media. A brief outline of critical research on non-human primates is also given. The lead isotope method is a powerful technique for tracing lead and could be employed more widely in human investigations

A new technique of "midline anchoring" in spinal cord stimulation dramatically reduces lead migration.

Science.gov (United States)

Mironer, Y Eugene; Brown, Christopher; Satterthwaite, John R; Cohen, Mary; Tonder, Lisa M; Grumman, Steve

2004-01-01

Spinal cord stimulation (SCS) is a popular method of treatment of chronic pain. Unfortunately, migration of the lead continues to be a serious complication of this therapy. In an attempt to reduce lateral migration of the SCS lead, we performed a retrospective assessment of a new technique of percutaneous lead placement. This new method of "midline anchoring" of the lead using the plica mediana dorsalis was tested against conventional technique in a retrospective study involving 122 trials and 91 implants of SCS over a period of five years. The use of "midline anchoring" resulted in a decrease in lead migration from 23% to 6% after trial insertion and from 24% to 7% after implantation. We conclude that "midline anchoring" of the SCS lead is an effective method of preventing lead migration.

SU-E-P-09: Radiation Transmission Measurements and Evaluation of Diagnostic Lead-Based and Lead-Free Aprons

Energy Technology Data Exchange (ETDEWEB)

Syh, J [Willis-Knighton Medical Center, Shreveport, LA (United States)

2014-06-01

Purpose: This study was conducted to ensure that various lead shield apron manufacturers provided accurate attenuation factors regardless of whether the apron was made of lead-based or lead-free equivalent material. Methods: A calibrated ionization survey meter was placed at chest height and 36 cm horizontally away from a solid water phantom on a simulator couch. Measurements were done with or without apron. Radiation field was set to 24cmx24cm with the phantom at 100cm source-to-surface distance. Irradiation time was set for 1 minute at voltages of 60, 80, 100 and 120 kVp. Current was set at 6mA. Results: Between 60 kVp and 120 kVp, the transmission through 0.50 mm of lead-based apron was between 1.0% and 6.5% with a mean value of 3.2% and a standard deviation (s.d.) of 1.4%. The transmissions through the 0.50 mm lead-free aprons were 1.0 % to 12.0% with a mean value of 6.1% and s.d. of 2.6%. At 120 kVp, the transmission value was 6.5% for 0.50 mm lead-based apron and 11.1% to 12.0% for 0.50 mm lead-free aprons. The radiation transmissions at 80 kVp, measured in two different 0.5 mm lead-free aprons, were 4.3% each. However, only 1.4% transmission was found through the lead-based apron. Overall, the radiation transmitted through the lead-based apron was 1/3 transmission of lead-free at 80kVp, and half value of lead-free aprons at 100 and 120 kVp. Conclusion: Even though lead-based and lead-free aprons all claimed to have the same lead equivalent thickness, the transmission might not be the same. The precaution was needed to exercise diligence in quality assurance program to assure adequate protection to staff who wear it during diagnostic procedures. The requirement for aprons not only should be in certain thickness to meet state regulation but also to keep reasonably achievable low exposure with the accurate labeling from manufacturers.

SU-E-P-09: Radiation Transmission Measurements and Evaluation of Diagnostic Lead-Based and Lead-Free Aprons

International Nuclear Information System (INIS)

Syh, J

2014-01-01

Purpose: This study was conducted to ensure that various lead shield apron manufacturers provided accurate attenuation factors regardless of whether the apron was made of lead-based or lead-free equivalent material. Methods: A calibrated ionization survey meter was placed at chest height and 36 cm horizontally away from a solid water phantom on a simulator couch. Measurements were done with or without apron. Radiation field was set to 24cmx24cm with the phantom at 100cm source-to-surface distance. Irradiation time was set for 1 minute at voltages of 60, 80, 100 and 120 kVp. Current was set at 6mA. Results: Between 60 kVp and 120 kVp, the transmission through 0.50 mm of lead-based apron was between 1.0% and 6.5% with a mean value of 3.2% and a standard deviation (s.d.) of 1.4%. The transmissions through the 0.50 mm lead-free aprons were 1.0 % to 12.0% with a mean value of 6.1% and s.d. of 2.6%. At 120 kVp, the transmission value was 6.5% for 0.50 mm lead-based apron and 11.1% to 12.0% for 0.50 mm lead-free aprons. The radiation transmissions at 80 kVp, measured in two different 0.5 mm lead-free aprons, were 4.3% each. However, only 1.4% transmission was found through the lead-based apron. Overall, the radiation transmitted through the lead-based apron was 1/3 transmission of lead-free at 80kVp, and half value of lead-free aprons at 100 and 120 kVp. Conclusion: Even though lead-based and lead-free aprons all claimed to have the same lead equivalent thickness, the transmission might not be the same. The precaution was needed to exercise diligence in quality assurance program to assure adequate protection to staff who wear it during diagnostic procedures. The requirement for aprons not only should be in certain thickness to meet state regulation but also to keep reasonably achievable low exposure with the accurate labeling from manufacturers

First detection of lead in black paper from intraoral film

Energy Technology Data Exchange (ETDEWEB)

Guedes, Debora F.C., E-mail: defcg@usp.br [Departamento de Odontologia Restauradora, Faculdade de Odontologia de Ribeirao Preto, Universidade de Sao Paulo, Av. do Cafe, S/N, Monte Alegre, CEP 14040-904, Ribeirao Preto, SP (Brazil); Silva, Reginaldo S. [Departamento de Odontologia Restauradora, Faculdade de Odontologia de Ribeirao Preto, Universidade de Sao Paulo, Av. do Cafe, S/N, Monte Alegre, CEP 14040-904, Ribeirao Preto, SP (Brazil); Veiga, Marcia A.M.S. da [Departamento de Quimica, Faculdade de Filosofia, Ciencias e Letras de Ribeirao Preto, Universidade de Sao Paulo, Av. do Cafe, S/N, Monte Alegre, CEP 14040-904, Ribeirao Preto, SP (Brazil); Pecora, Jesus D. [Departamento de Odontologia Restauradora, Faculdade de Odontologia de Ribeirao Preto, Universidade de Sao Paulo, Av. do Cafe, S/N, Monte Alegre, CEP 14040-904, Ribeirao Preto, SP (Brazil)

2009-10-30

Lead (Pb) contamination in the black paper that recovers intraoral films (BKP) has been investigated. BKP samples were collected from the Radiology Clinics of the Dental School of Ribeirao Preto, University of Sao Paulo, Brazil. For sake of comparison, four different methods were used. The results revealed the presence of high lead levels, well above the maximum limit allowed by the legislation. Pb contamination levels achieved after the following treatments: paper digestion in nitric acid, microwave treatment, DIN38414-54 method and TCLP method were 997 {mu}g g{sup -1}, 189 {mu}g g{sup -1}, 20.8 {mu}g g{sup -1}, and 54.0 {mu}g g{sup -1}, respectively. Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma mass spectrometry (ICP-MS) were employed for lead determination according to the protocols of the applied methods. Lead contamination in used BKP was confirmed by scanning electron microscopy coupled with energy dispersive X-ray microanalysis (SEM-EDS). All the SEM imaging was carried out in the secondary electron mode (SE) and backscattered-electron mode (QBSD) following punctual X-ray fluorescence spectra. Soil contamination derived from this product revealed the urgent need of addressing this problem. These elevated Pb levels, show that a preliminary treatment of BKP is mandatory before it is disposed into the common trash. The high lead content of this material makes its direct dumping into the environment unwise.

Lead exposure biomarkers and mini-mental status exam scores in older men

NARCIS (Netherlands)

Wright, RO; Tsaih, SW; Schwartz, J; Spiro, A; McDonald, K; Weiss, ST; Hu, H

2003-01-01

Background: Lead is neurotoxic; yet, whether cognitive decline in older persons is associated with lead exposure is unknown. We studied whether lead exposure biomarkers are associated with cognitive test scores, as well as the modifying effects of age on the lead-cognition relationship. Methods:

Lead exposure biomarkers and mini-mental status exam scores in older men

NARCIS (Netherlands)

Wright, RO; Tsaih, SW; Schwartz, J; Spiro, A; McDonald, K; Weiss, ST; Hu, H

Background: Lead is neurotoxic; yet, whether cognitive decline in older persons is associated with lead exposure is unknown. We studied whether lead exposure biomarkers are associated with cognitive test scores, as well as the modifying effects of age on the lead-cognition relationship. Methods:

An exploratory study of lead recovery in lead-acid battery lifecycle in US market: An evidence-based approach

International Nuclear Information System (INIS)

Genaidy, A.M.; Sequeira, R.; Tolaymat, T.; Kohler, J.; Rinder, M.

2008-01-01

Background: This research examines lead recovery and recycling in lead-acid batteries (LAB) which account for 88% of US lead consumption. We explore strategies to maximize lead recovery and recycling in the LAB lifecycle. Currently, there is limited information on recycling rates for LAB in the published literature and is derived from a single source. Therefore, its recycling efforts in the US has been unclear so as to determine the maximum opportunities for metal recovery and recycling in the face of significant demands for LAB particularly in the auto industry. Objectives: The research utilizes an evidence-based approach to: (1) determine recycling rates for lead recovery in the LAB product lifecycle for the US market; and (2) quantify and identify opportunities where lead recovery and recycling can be improved. Methods: A comprehensive electronic search of the published literature was conducted to gather information on different LAB recycling models and actual data used to calculate recycling rates based on product lifecycle for the US market to identify strategies for increasing lead recovery and recycling. Results: The electronic search yielded five models for calculating LAB recycling rates. The description of evidence was documented for each model. Furthermore, an integrated model was developed to identify and quantify the maximum opportunities for lead recovery and recycling. Results showed that recycling rates declined during the period spanning from 1999 to 2006. Opportunities were identified for recovery and recycling of lead in the LAB product lifecycle. Concluding remarks: One can deduce the following from the analyses undertaken in this report: (1) lead recovery and recycling has been stable between 1999 and 2006; (2) lead consumption has increased at an annual rate of 2.25%, thus, the values derived in this study for opportunities dealing with lead recovery and recycling underestimate the amount of lead in scrap and waste generated; and (3) the

Radiometric trace analysis of lead with diethyldithiocarbamate and 204T1

NARCIS (Netherlands)

Erkelens, P.C. van

1962-01-01

Two methods for the determination of submugram amounts of lead are described. (A) Lead is selectively extracted with carbon tetrachloride from an alkaline solution containing exccss diethyl-dithiocarbamatc (DDC) and cyanide. Traces of DDC arc back-extracted. The lead in the DDC complex is exchanged

Mussels (Mytilus sp.) as an indicator of lead pollution

International Nuclear Information System (INIS)

Chow, T.J.; Snyder, H.G.; Snyder, C.B.

1976-01-01

The lead contents of two species of mussels (Mytilus californianus and M. edulis) collected along the Pacific coast from Piedras Blancas, California to Punta Bnada, Baja California were determined by isotope dilution method. The whole soft parts of the mussels, on a dry weight basis, contained from 0.27 to 42 ppm of lead which can be related to their local habitats. The gill tissues of the mussels showed the highest lead concentration

Investigating the Formation Process of Sn-Based Lead-Free Nanoparticles with a Chemical Reduction Method

International Nuclear Information System (INIS)

Zhang, W.; Zhao, B.; Gao, Y.; Zhang, W.; Zhao, B.; Zou, Ch.; Zhai, Q.; Gao, Y.; Gao, Y.; Acquah, S.F.A.

2013-01-01

Nanoparticles of a promising lead-free solder alloy (Sn 3.5 Ag (wt.%, Sn Ag) and Sn 3.0 Ag 0.5 Cu (wt.%, SAC)) were synthesized through a chemical reduction method by using anhydrous ethanol and 1,10-phenanthroline as the solvent and surfactant, respectively. To illustrate the formation process of Sn-Ag alloy based nanoparticles during the reaction, X-ray diffraction (XRD) was used to investigate the phases of the samples in relation to the reaction time. Different nucleation and growth mechanisms were compared on the formation process of the synthesized nanoparticles. The XRD results revealed different reaction process compared with other researchers. There were many contributing factors to the difference in the examples found in the literature, with the main focus on the formation mechanism of crystal nuclei, the solubility and ionizability of metal salts in the solvent, the solid solubility of Cu in Ag nuclei, and the role of surfactant on the growth process. This study will help define the parameters necessary for the control of both the composition and size of the nanoparticles

Use of an automated X-ray fluorescence method in the study of pollution due to lead and bromine from automobiles

International Nuclear Information System (INIS)

Jeanmaire, L.; Gros, R.; Patti, F.; Goujon Beauvivier, M. de; Laporte, J.

1976-01-01

The authors first describe an automated method for determining, by X-ray fluorescence, mineral pollutants present in the air in particulate form. The fluorescence spectrometer employed is a wavelength-dispersive commercial model. It is connected to a recording unit by means of which one can obtain the spectrum on punched tape; the spectrum is then analysed by computer. The calibration method and the performance characteristics are described. In the second part of the paper, the results are presented of monthly measurements of lead and bromine in the air, performed over a period of several years at four stations in different types of location. The mean Pb/Br ratio is not the same for all the stations. A seasonal variation of the ratio shows up clearly in the Paris region. (author)

The next-to-leading order (NLO) gluon distribution from DGLAP ...

Indian Academy of Sciences (India)

leading order (NLO) is obtained by applying the method of characteristics. Its compatibility with double leading logarithmic approximation (DLLA) asymptotics is discussed and comparison with the exact ones like GRV98NLO is made. The solution ...

Lead and lead-based alloys as waste matrix materials

International Nuclear Information System (INIS)

Arustamov, A.E.; Ojovan, M.I.; Kachalov, M.B.

1999-01-01

Metals and alloys with relatively low melting temperatures such as lead and lead-based alloys are considered in Russia as prospective matrices for encapsulation of spent nuclear fuel in containers in preparation for final disposal in underground repositories. Now lead and lead-based alloys are being used for conditioning spent sealed radioactive sources at radioactive waste disposal facilities

Lead poisoning

Science.gov (United States)

... drinking water in homes containing pipes that were connected with lead solder . Although new building codes require ... lead in their bodies when they put lead objects in their mouths, especially if they swallow those ...

Determination of lead and cadmium in biological materials

International Nuclear Information System (INIS)

Stoeppler, M.; Backhaus, F.; Dahl, R.; Hagedorn-Goetz, H.; Hilpert, K.; Klahre, P.; Rutzel, H.; Valenta, P.; Nuernberg, H.W.; Dumont, M.

1975-01-01

Sampling techniques and experience, and decomposition methods are presented. The processes used in flameless atomic absorption spectrometry (including the method using automatic insertion of samples), pulse polarography and isotope dilution mass spectrometry are described. Finally, the results of lead and cadmium measurements in bovine liver, blood, urine and hair samples are reported and discussed with a comparison of methods in some cases

Sparse Matrix for ECG Identification with Two-Lead Features

Directory of Open Access Journals (Sweden)

Kuo-Kun Tseng

2015-01-01

Full Text Available Electrocardiograph (ECG human identification has the potential to improve biometric security. However, improvements in ECG identification and feature extraction are required. Previous work has focused on single lead ECG signals. Our work proposes a new algorithm for human identification by mapping two-lead ECG signals onto a two-dimensional matrix then employing a sparse matrix method to process the matrix. And that is the first application of sparse matrix techniques for ECG identification. Moreover, the results of our experiments demonstrate the benefits of our approach over existing methods.

Lead Poisoning

Science.gov (United States)

Lead is a metal that occurs naturally in the earth's crust. Lead can be found in all parts of our ... from human activities such as mining and manufacturing. Lead used to be in paint; older houses may ...

New method for cardiac resynchronization therapy: Transapical endocardial lead implantation for left ventricular free wall pacing

NARCIS (Netherlands)

I. Kassai (Imre); C. Foldesi (Csaba); A. Szekely (Andrea); T. Szili-Torok (Tamas)

2008-01-01

textabstractCoronary sinus lead placement for transvenous left ventricular (LV) pacing in cardiac resynchronization therapy (CRT) has a significant failure rate at implant and a significant dislocation rate during follow-up. For these patients, epicardial pacing lead implantation is the most

Lead activity in Pb-Sb-Bi alloys

Directory of Open Access Journals (Sweden)

A. S. Kholkina

2014-11-01

Full Text Available The present work is devoted to the study of lead thermodynamic activity in the Pb-Sb-Bi alloys. The method for EMF measurements of the concentration cell: (–Pb|KCl-PbCl2¦¦KCl-PbCl2|Pb-(Sb-Bi(+ was used. The obtained concentration dependences of the galvanic cell EMF are described by linear equations. The lead activity in the ternary liquid-metal alloy demonstrates insignificant negative deviations from the behavior of ideal solutions.

ANALYSIS OF AGRICULTURAL LEADING SUBSECTOR DISTRICT/CITIES IN BENGKULU PROVINCE

Directory of Open Access Journals (Sweden)

Agung Ridho Pratama

2017-12-01

Full Text Available The purpose of this study was to determine the agricultural leading subsector in the districts/ cities in Bengkulu Province and the conditions of agricultural leading  subsectors  district/ cites status as a Main Area in Bengkulu Province before and after the expansion area. The analysis method used Location Quotient (LQ, Dynamic Location Quotient (DLQ, Shift-Share analysis (SS and Overlay analysis. The study used secondary data, such as Gross Domestic Regional Bruto (PDRB of districts/cities in Bengkulu Province and Bengkulu Province from 2004 until 2014 based on constant basic price. The result of this study showed that agricultural leading subsector based on the overlay analysis (combined analysing from three analysis method are livestock subsector and plantation crops subsector, sepecially in Bengkulu City and Kaur. In South Bengkulu, before the expansion area, the fisheries subsector to be the only agricultural leading subsector. After the expansion, the agricultural leading subsectors increased to fisheries subsector and livestock subsector. In Rejang Lebong, food crops subsector remains a agricultural leading subsectors both before and after doing the expansion area. Meanwhile, in North Bengkulu, before the expansion area livestock subsector as the agricultural leading subsector. When do expansion area, position of the livestock subsector replaced by fisheries subsector.

Lead Test

Science.gov (United States)

... to do renovation and repair projects using lead-safe work practices to avoid creating more lead dust or ... in a dangerous area? Yes. If you are working in a potentially harmful environment with exposure to lead dust or fumes: Wash ...

Association of Lead Exposure, Serum Uric Acid and Parameters of Renal Function in Nigerian Lead-Exposed Workers

Directory of Open Access Journals (Sweden)

DD Alasia

2010-09-01

Full Text Available Background: The presence of hyperuricemia and renal function impairment, especially in the absence of urate stone formation is strongly suggestive of lead nephropathy. The evaluation of this association is essential in areas where lead exposure is still prevalent and uncontrolled. Objective: To determine the relationship between serum uric acid and renal function indices in lead-exposed workers. Methods: A cross-sectional study of 190 adults with occupational lead exposure and 80 adults (comparison group, matched for age and sex was performed in Port Harcourt, South-south Nigeria. Blood lead was used as the biomarker of lead exposure while serum urea, serum creatinine, urine albumin (using urine albumin:creatinine ratio, estimated glomerular filtration rate (GFR and serum uric acid were the renal function indices measured. Results: Occupationally lead-exposed subjects had a significantly (p = 0.008 higher mean±SD blood lead levels (50.37±24.58 μg/dL than the comparison group (41.40±26.85. The mean±SD serum urea (8.6±2.3 mg/dL, creatinine (1.0±0.2 mg/dL and serum uric acid (4.6±1.2 mg/dL were significantly (p < 0.01 higher in the study subjects than the comparison group (7.6±2.4, 0.9±0.2, and 3.9±1.1 mg/dL, respectively. The mean±SD creatinine clearance was significantly (p = 0.002 lower in the study subjects than the comparison group (98.9±21.3 vs. 108.2±25.2 mL/min/1.72 m2. Serum uric acid level correlated positively with serum creatinine (r = 0.134 and negatively with GFR (r = ‑0.151. Conclusion: People with occupational lead exposure are at risk of developing hyperuricemia and renal impairment.

Examining Public Perceptions about Lead in School Drinking Water: A Mixed-Methods Analysis of Twitter Response to an Environmental Health Hazard.

Science.gov (United States)

Ekenga, Christine C; McElwain, Cora-Ann; Sprague, Nadav

2018-01-20

Exposure to lead has long been a community health concern in St. Louis, Missouri. The objective of this study was to examine public response to reports of elevated lead levels in school drinking water in St. Louis, Missouri via Twitter, a microblogging platform with over 320 million active users. We used a mixed-methods design to examine Twitter user status updates, known as "tweets," from 18 August to 31 December 2016. The number of tweets each day was recorded, and Twitter users were classified into five user types (General Public, Journalist/News, Health Professional/Academic, Politician/Government Official, and Non-Governmental Organization). A total of 492 tweets were identified during the study period. The majority of discourse on Twitter occurred during the two-week period after initial media reports and was driven by members of the General Public. Thematic analysis of tweets revealed four themes: Information Sharing, Health Concerns, Sociodemographic Disparities, and Outrage. Twitter users characterized lead in school drinking water as an issue of environmental inequity. The findings of this study provide evidence that social media platforms can be utilized as valuable tools for public health researchers and practitioners to gauge public sentiment about environmental health issues, identify emerging community concerns, and inform future communication and research strategies regarding environmental health hazards.

Bulk diffusion and solubility of silver and nickel in lead, lead-silver and lead-nickel solid solutions

International Nuclear Information System (INIS)

Amenzou-Badrour, H.; Moya, G.; Bernardini, J.

1988-01-01

The results of a study of solubility and bulk diffusion of /sup 110/Ag and /sup 63/Ni in lead, lead-silver and lead-nickel solid solutions in the temperature range 220 to 88 0 C are reported. Owing to the low solubility of silver and nickel in lead, Fick's solution corresponding to the boundary condition of a constant concentration of solute at the surface has been used. Depth profile concentration analysis suggests a fundamental difference between the diffusion mechanisms of silver and nickel. Since silver penetration profiles in pure lead give diffusion coefficients independent of the penetration depth and silver concentration, it is suggested that slight decreases of silver diffusivity in lead-silver solid solutions have no significance. This implies that the interstitial silver atoms do not associate significantly with each other to form Ag-Ag dimers. In contrast, different behaviors of /sup 63/Ni depth profile concentration in pure lead and saturated PbNi solid solutions agree with a Ni-Ni interaction leading to the formation of less mobile dimers near the surface in pure lead

Toxicological analysis of the risk of lead exposure in metal processing

African Journals Online (AJOL)

concentration and biological lead toxicity markers in blood and urine were performed for both exposed ... biological samples were determined by spectrophotometric methods. Results: The ..... Occupational lead exposure of storage battery.

Electrical properties of a novel lead alkoxide precursor: Lead glycolate

International Nuclear Information System (INIS)

Tangboriboon, Nuchnapa; Pakdeewanishsukho, Kittikhun; Jamieson, Alexander; Sirivat, Anuvat; Wongkasemjit, Sujitra

2006-01-01

The reaction of lead acetate trihydrate Pb(CH 3 COO) 2 .3H 2 O and ethylene glycol, using triethylenetetramine (TETA) as a catalyst, provides in one step access to a polymer-like precursor of lead glycolate [-PbOCH 2 CH 2 O-]. On the basis of high-resolution mass spectroscopy, chemical analysis composition, FTIR, 13 C-solid state NMR and TGA, the lead glycolate precursor can be identified as a trimer structure. The FTIR spectrum demonstrates the characteristics of lead glycolate; the peaks at 1086 and 1042 cm -1 can be assigned to the C-O-Pb stretchings. The 13 C-solid state NMR spectrum gives notably only one peak at 68.639 ppm belonging to the ethylene glycol ligand. The phase transformations of lead glycolate and lead acetate trihydrate to lead oxide, their microstructures, and electrical properties were found to vary with increasing temperature. The lead glycolate precursor has superior electrical properties relative to those of lead acetate trihydrate, suggesting that the lead glycolate precursor can possibly be used as a starting material for producing electrical and semiconducting ceramics, viz. ferroelectric, anti-ferroelectric, and piezoelectric materials

Testing for lead in toys at day care centers.

Science.gov (United States)

Sanders, Martha; Stolz, Julie; Chacon-Baker, Ashley

2013-01-01

Exposure to lead-based paint or material has been found to impact children's cognitive and behavioral development at blood lead levels far below current standards. The purpose of the project was to screen for lead in toy items in daycare centers in order to raise awareness of inside environmental lead exposures and minimize lead-based exposures for children. Occupational therapy students in a service learning class tested for lead in ten daycare or public centers using the XRF Thermo Scientific Niton XL3t, a method accepted by the Consumer Product Safety Commission (CPSC). A total of 460 items were tested over a two-month period for an average of 66 toys per setting. Fifty six (56) items tested > 100 ppm, which represented 12% of the entire sample. Items with high lead levels included selected toys constructed with lead-based paint, lead metals, plastics using lead as a color enhancer, and decorative objects. While the actual number of lead-based products is small, the cumulative exposure or habitual use may pose an unnecessary risk to children. Indoor exposures occurred for all day care centers regardless of socio-economic levels. Recommendations to minimize exposures are provided.

Relational Leading

DEFF Research Database (Denmark)

Larsen, Mette Vinther; Rasmussen, Jørgen Gulddahl

2015-01-01

This first chapter presents the exploratory and curious approach to leading as relational processes – an approach that pervades the entire book. We explore leading from a perspective that emphasises the unpredictable challenges and triviality of everyday life, which we consider an interesting......, relevant and realistic way to examine leading. The chapter brings up a number of concepts and contexts as formulated by researchers within the field, and in this way seeks to construct a first understanding of relational leading....

Lead exposure among young urban women

Directory of Open Access Journals (Sweden)

Moline Jacqueline M.

1999-01-01

Full Text Available Objective. Blood lead levels have declined among every age group in the United States, but urban minority residents remain at disproportionate risk for elevated lead levels. Our objective was to measure lead burden in young women of childbearing age in New York City. We also describe successful means of recruiting this population into a cohort study. Material and methods. Healthy women aged 18-25 attending a New York City health care center in 1995-1998 were eligible for participation. Participants were recruited by health care providers, the study coordinator and the participants themselves. Venous blood samples were obtained for whole blood lead, ferritin and hematocrit measurements, and detailed questionnaires were administered. Results. 239 women have been recruited to date. The population is predominately minority: 62% African-American, 33% Hispanic and 5% Caucasian/Asian. The average age of participants is 19.3 years. Recruitment of participants into the study is predominantly (55% through "word of mouth" from previously enrolled participants. Few participants learned of the study through their health care providers. The mean blood lead level among study participants is 2.1 ± 1.7 µg/dl, which is consistent with the most recent United States national survey. Conclusions. Blood lead levels are low in young, urban minority women of childbearing age in New York City. In this population, recruitment efforts were substantially enhanced with the help of enrolled participants and the health care community.

Sol-gel preparation of lead magnesium niobate (PMN) powders and thin films

Science.gov (United States)

Boyle, T.J.

1999-01-12

A method of preparing a lead magnesium niobium oxide (PMN), Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}, precursor solution by a solvent method wherein a liquid solution of a lead-complex PMN precursor is combined with a liquid solution of a niobium-complex PMN precursor, the combined lead- and niobium-complex liquid solutions are reacted with a magnesium-alkyl solution, forming a PMN precursor solution and a lead-based precipitate, and the precipitate is separated from the reacted liquid PMN precursor solution to form a precipitate-free PMN precursor solution. This precursor solution can be processed to form both ferroelectric powders and thin films. 3 figs.

Do US Ambient Air Lead Levels Have a Significant Impact on Childhood Blood Lead Levels: Results of a National Study

Directory of Open Access Journals (Sweden)

LuAnn L. Brink

2013-01-01

Full Text Available Introduction. Although lead paint and leaded gasoline have not been used in the US for thirty years, thousands of US children continue to have blood lead levels (BLLs of concern. Methods. We investigated the potential association of modeled air lead levels and BLLs ≥ 10 μg/dL using a large CDC database with BLLs on children aged 0–3 years. Percent of children with BLLs ≥ 10 μg/dL (2000–2007 by county and proportion of pre-50 housing and SES variables were merged with the US EPA's National Air Toxics Assessment (NATA modeled air lead data. Results. The proportion with BLL ≥ 10 μg/dL was 1.24% in the highest air lead counties, and the proportion with BLL ≥ 10 μg/dL was 0.36% in the lowest air lead counties, resulting in a crude prevalence ratio of 3.4. Further analysis using multivariate negative binomial regression revealed that NATA lead was a significant predictor of % BLL ≥ 10 μg/dL after controlling for percent pre-l950 housing, percent rural, and percent black. A geospatial regression revealed that air lead, percent older housing, and poverty were all significant predictors of % BLL ≥ 10 μg/dL. Conclusions. More emphasis should be given to potential sources of ambient air lead near residential areas.

Correlation between some parameters of lead absorption and lead intoxication

Science.gov (United States)

Waldron, H. A.

1971-01-01

Waldron, H. A. (1971).Brit. J. industr. Med.,28, 195-199. Correlation between some parameters of lead absorption and lead intoxication. Use has been made of data collected over a number of years from workers exposed to a lead hazard in a motor-car factory. The correlations between various parameters of lead absorption and lead intoxication were computed, including blood and urine lead concentrations, urinary coproporphyrin, ALA and PBG concentrations, and haemoglobin concentration. In all, 15 correlation coefficients were calculated, of which only six showed a statistically significant result (i.e., Plead and urine lead (r = 0·38, Plead and coproporphyrin (r = 0·42, Plead and ALA (r = 0·43, Plead and PBG (r = 0·19, P<0·05). PMID:5572689

Lead arthropathy: radiographic, CT and MRI findings

International Nuclear Information System (INIS)

Fernandes, Joao Luiz; Lopes Rocha, Arthemizio Antonio; Veloso Ayrimoraes Soares, Mayra; Lopes Viana, Sergio

2007-01-01

Lead arthropathy is a well-known complication of gunshot injuries with retained intra-articular bullets. Although several previous reports have discussed the radiological findings of this entity, computed tomography (CT) and magnetic resonance imaging (MRI) findings have never been described before in this setting. In this paper the authors review the imaging findings of 11 patients with lead arthropathy (1 of whom had clinical signs of lead poisoning as well), all of them studied by means of radiographs. In addition, non-enhanced CT scans were obtained in 3 patients and gadolinium-enhanced MRI in 1. Classic findings of intra-articular speckled lead deposits (occasionally with a ''lead arthrogram'' appearance), joint space narrowing and preserved bone density were found at radiographs in the great majority of cases. Furthermore, extension of intra-articular lead to adjacent tendon sheaths was observed in almost half of the patients, an observation rarely reported in the literature. CT scans and MRI, in their turn, were superior with regard to soft tissue abnormalities, accurately depicting joint effusion and the thickened synovium with lead particles embedded in it. Post-gadolinium MRI had the advantage of showing the enhancement pattern of the inflamed synovium and associated bone marrow edema pattern. Although it is not possible to establish the role of axial imaging in lead arthropathy from the small number of cases studied, this initial experience shows that both methods hold promise in this setting and may be useful, at least in selected cases. (orig.)

Total neutron cross section of lead

International Nuclear Information System (INIS)

Kanda, K.; Aizawa, O.

1976-01-01

The total thermal-neutron cross section of natural lead under various physical conditions was measured by the transmission method. It became clear that the total cross section at room temperature previously reported is lower than the present data. The total cross section at 400, 500, and 600 0 C, above the melting point of lead, 327 0 C, was also measured, and the changes in the cross section as a function of temperature were examined, especially near and below the melting point. The data obtained for the randomly oriented polycrystalline state at room temperature were in reasonable agreement with the theoretical values calculated by the THRUSH and UNCLE-TOM codes

Scaling violations beyond the leading order

CERN Document Server

Petronzio, R

1981-01-01

The authors are concerned with the explicit construction of a method which generalizes beyond leading order the simple probabilistic interpretation of leading scaling violations. The results obtained in this language allow to predict the evolution with the variation of external invariants not only of 'space-like' processes, where the off- shell partons starting the hard interaction have space-like four momenta, like in the case of deep inelastic scattering or Drell-Yan, but also of 'time-like' processes, like the one-particle inclusive e /sup +/e/sup -/ annihilation, where the partons acting in the fragmentation functions have 'time-like' off-shell invariant masses. (9 refs).

Lead-Time Models Should Not Be Used to Estimate Overdiagnosis in Cancer Screening

DEFF Research Database (Denmark)

Zahl, Per-Henrik; Jørgensen, Karsten Juhl; Gøtzsche, Peter C

2014-01-01

screening--the excess-incidence approach and the lead-time approach--that rely on two different lead-time definitions. Overdiagnosis when screening with mammography has varied from 0 to 75 %. We have explained that these differences are mainly caused by using different definitions and methods......Lead-time can mean two different things: Clinical lead-time is the lead-time for clinically relevant tumors; that is, those that are not overdiagnosed. Model-based lead-time is a theoretical construct where the time when the tumor would have caused symptoms is not limited by the person's death....... It is the average time at which the diagnosis is brought forward for both clinically relevant and overdiagnosed cancers. When screening for breast cancer, clinical lead-time is about 1 year, while model-based lead-time varies from 2 to 7 years. There are two different methods to calculate overdiagnosis in cancer...

Tellurium self-diffusion and point defects in lead telluride

International Nuclear Information System (INIS)

Simirskij, Yu.N.; Firsova, L.P.

1982-01-01

Method of radioactive indicators was used to determine factors of tellurium self-diffusion in lead telluride with different deviation of the composition from stoichiometric in the range of enrichment by tellurium. It was found that at 973 K factors of tellurium self-diffusion in lead telluride depend slightly on the vapor pressure of tellurium equilibrium with solid phase

Does thiosemicarbazide lead nitrate (TSLN) crystal exist?

OpenAIRE

Fernandes, R.; Srinivasan, Bikshandarkoil R.

2016-01-01

The authors of a recent paper (Optik 125 (2014) 2022-2025) claim to have grown a so called thiosemicarbazide lead nitrate (TSLN) crystal by the slow evaporation method. In this comment we prove that TSLN is actually thiosemicarbazide.

Increased bone calcium dissociation in lead-exposed rats

Directory of Open Access Journals (Sweden)

Eko Suhartono

2012-12-01

Full Text Available Background Lead is still a major environmental and occupational health hazard, since it is extensively used in the production of paints, gasoline and cosmetics. This causes the metal to be ubiquitous in the environment, being found in the air, soil, and water, from which it can enter the human body by inhalation or ingestion. Absorbed lead is capable of altering the calcium levels in bone. The aim of this study was to demonstrate the effect of lead on bone calcium levels by measuring the reaction constant, Gibbs free energy, and enthalpy. Methods This study was of pure experimental design using 100 male albino rats (Rattus norvegicus. The experimental animals were assigned by simple randomization to two groups, one group receiving lead acetate orally at a dosage of 100 mg/kgBW, while the other group did not receive lead acetate. The intervention was given for 4 weeks and the rats were observed weekly for measurement of bone calcium levels by the permanganometric method. Results This study found that k1 (hydroxyapatite dissociation rate constant was 0.90 x 10-3 dt-1, and that k2 (hydroxyapatite association rate constant was 6.16 x 10-3 dt-1 for the control group, whereas for the intervention group k1 = 26.20 x 10-3 dt-1 and k2 = 16.75 x 10-3 dt-1. Thermodynamically, the overall reaction was endergonic and endothermic (DG > 0 and DH > 0. ConclusionS Lead exposure results in increased dissociation rate of bone in comparison with its association rate. Overall, the reaction was endergonic and endothermic (DG > 0 and DH > 0.

Increased bone calcium dissociation in lead-exposed rats

Directory of Open Access Journals (Sweden)

Eko Suhartono

2015-12-01

Full Text Available BACKGROUND Lead is still a major environmental and occupational health hazard, since it is extensively used in the production of paints, gasoline and cosmetics. This causes the metal to be ubiquitous in the environment, being found in the air, soil, and water, from which it can enter the human body by inhalation or ingestion. Absorbed lead is capable of altering the calcium levels in bone. The aim of this study was to demonstrate the effect of lead on bone calcium levels by measuring the reaction constant, Gibbs free energy, and enthalpy. METHODS This study was of pure experimental design using 100 male albino rats (Rattus norvegicus. The experimental animals were assigned by simple randomization to two groups, one group receiving lead acetate orally at a dosage of 100 mg/ kgBW, while the other group did not receive lead acetate. The intervention was given for 4 weeks and the rats were observed weekly for measurement of bone calcium levels by the permanganometric method. RESULTS This study found that k1 (hydroxyapatite dissociation rate constant was 0.90 x 10-3 dt-1, and that k2 (hydroxyapatite association rate constant was 6.16 x 10-3 dt-1 for the control group, whereas for the intervention group k1 = 26.20 x 10-3 dt-1 and k2 = 16.75 x 10-3 dt-1. Thermodynamically, the overall reaction was endergonic and endothermic (ΔG > 0 and ΔH > 0. CONCLUSIONS Lead exposure results in increased dissociation rate of bone in comparison with its association rate. Overall, the reaction was endergonic and endothermic (ΔG > 0 and ΔH > 0.

Human health risk assessment of lead from mining activities at semi-arid locations in the context of total lead exposure.

Science.gov (United States)

Zheng, Jiajia; Huynh, Trang; Gasparon, Massimo; Ng, Jack; Noller, Barry

2013-12-01

Lead from historical mining and mineral processing activities may pose potential human health risks if materials with high concentrations of bioavailable lead minerals are released to the environment. Since the Joint Expert Committee on Food Additives of Food and Agriculture Organization/World Health Organization withdrew the Provisional Tolerable Weekly Intake of lead in 2011, an alternative method was required for lead exposure assessment. This study evaluated the potential lead hazard to young children (0-7 years) from a historical mining location at a semi-arid area using the U.S. EPA Integrated Exposure Uptake Biokinetic (IEUBK) Model, with selected site-specific input data. This study assessed lead exposure via the inhalation pathway for children living in a location affected by lead mining activities and with specific reference to semi-arid conditions and made comparison with the ingestion pathway by using the physiologically based extraction test for gastro-intestinal simulation. Sensitivity analysis for major IEUBK input parameters was conducted. Three groups of input parameters were classified according to the results of predicted blood concentrations. The modelled lead absorption attributed to the inhalation route was lower than 2 % (mean ± SE, 0.9 % ± 0.1 %) of all lead intake routes and was demonstrated as a less significant exposure pathway to children's blood, compared with ingestion. Whilst dermal exposure was negligible, diet and ingestion of soil and dust were the dominant parameters in terms of children's blood lead prediction. The exposure assessment identified the changing role of dietary intake when house lead loadings varied. Recommendations were also made to conduct comprehensive site-specific human health risk assessment in future studies of lead exposure under a semi-arid climate.

Lead intoxication: clinic and diagnostic evaluation in children

Directory of Open Access Journals (Sweden)

Martínez-Riera Nora

2012-03-01

Full Text Available Poverty, poor nutrition, environmental and social injustice prevailing in Latin America are factorsthat determine the action of pollutants on children. Lead poisoning and pollution constitute apublic health problem throughout the world. Lead affects multiple organs: nervous system particularly,hematopoietic, renal, endocrine, bone and others. Objective: to assess clinical, biochemicaland vascular effects in children exposed to known source of lead. Materials and methods: Sevenchildren with defined source lead exposure were studied, general and specific lead laboratorywere made. Endothelial function and electrocardiographic parameters were assessed. Statistic:descriptive. Results: Age average was 6,2 years (DE± 1, 6, average haematocrit 31% (DE±0,02;hemoglobin average 10,2 g/dl (DE± 0,78. 100% presented hypochromia, microcitosis, anemiaand marked anisocytosis. Lead average: 37,9 ug/dl (DE±6,22, ALA-D average: 8,9 U/L (DE±4,5.No changes were found in lipid profile and kidney function. All presented microalbuminuriaand endothelial dysfunction. Conclusion: These results show the effects of environmental leadexposure that can result in children not occupationally exposed.

Measurements of total lead concentrations and of lead isotope ratios in whole blood by use of inductively coupled plasma source mass spectrometry

International Nuclear Information System (INIS)

Delves, H.T.; Campbell, M.J.

1988-01-01

Methods are described for the accurate and precise determination of total lead and its isotopic composition in whole blood using inductively coupled plasma source mass spectrometry (ICP-MS). Sensitivities of up to 3 x 10 6 counts s -1 for 208 Pb at a total lead concentration of 5 μmol l -1 (1 μg ml -1 ) enabled total blood lead levels to be measured in 4 min per sample, with a detection limit of 0.072 μmol l -1 (15 μg l -1 ). The agreement between ICP-MS and atomic absorption spectrometry (AAS) for this analysis was excellent: ICP-MS 0.996 x AAS -0.0165 μmol l -1 ; r 0.994. Isotope ratio measurements required 15 min to achieve the required accuracy and precision both of which were generally better than 0.5% for 206 Pb: 207 Pb and 208 Pb: 206 Pb isotopic lead ratios. The ICP-MS data for these ratios in ten quality control blood specimens has a mean bias relative to isotope dilution mass spectrometry of -0.412% for 206 Pb: 207 Pb ratios and of +0.055% for the 208 Pb: 206 Pb ratios. This level of accuracy and that of the total blood lead measurements is sufficient to permit application of these ICP-MS methods to environmental studies. (author)

The identification of lead ammunition as a source of lead exposure in First Nations: The use of lead isotope ratios

International Nuclear Information System (INIS)

Tsuji, Leonard J.S.; Wainman, Bruce C.; Martin, Ian D.; Sutherland, Celine; Weber, Jean-Philippe; Dumas, Pierre; Nieboer, Evert

2008-01-01

The use of lead shotshell to hunt water birds has been associated with lead-contamination in game meat. However, evidence illustrating that lead shotshell is a source of lead exposure in subsistence hunting groups cannot be deemed definitive. This study seeks to determine whether lead shotshell constitutes a source of lead exposure using lead isotope ratios. We examined stable lead isotope ratios for lichens, lead shotshell and bullets, and blood from residents of Fort Albany and Kashechewan First Nations, and the City of Hamilton, Ontario, Canada. Data were analyzed using ANOVA and regression analyses. ANOVA of isotope ratios for blood revealed significant differences with respect to location, but not sex. Hamilton differed from both Kashechewan and Fort Albany; however, the First Nations did not differ from each other. ANOVA of the isotope ratios for lead ammunition and lichens revealed no significant differences between lichen groups (north and south) and for the lead ammunition sources (pellets and bullets). A plot of 206 Pb/ 204 Pb and 206 Pb/ 207 Pb values illustrated that lichens and lead ammunition were distinct groupings and only the 95% confidence ellipse of the First Nations group overlapped that of lead ammunition. In addition, partial correlations between blood-lead levels (adjusted for age) and isotope ratios revealed significant (p 206 Pb/ 204 Pb and 206 Pb/ 207 Pb, and a significant negative correlation for 208 Pb/ 206 Pb, as predicted if leaded ammunition were the source of lead exposure. In conclusion, lead ammunition was identified as a source of lead exposure for First Nations people; however, the isotope ratios for lead shotshell pellets and bullets were indistinguishable. Thus, lead-contaminated meat from game harvested with lead bullets may also be contributing to the lead body burden

Effect on blood lead of airborne lead particles characterized by size.

Science.gov (United States)

Park, Dong-Uk; Paik, Nam-Won

2002-03-01

Worker exposure to airborne lead particles was evaluated for a total of 117 workers in 12 work-places of four different industrial types in Korea. The particle sizes were measured using 8-stage cascade impactors worn by the workers. Mass median aerodynamic diameters (MMAD) were determined by type of industry and percentage of lead particles as a fraction of airborne lead (PbA) concentration was determined by particle size. Blood lead (PbB) levels of workers who matched airborne lead samples were also examined. A Scheffé's pairwise comparison test showed that MMAD and the fractions of each of respirable particles and lead particles lead particles lead particles (r = 0.82) than that between concentrations of small particles and PbA (r = 0.61). A simple linear regression indicated that PbB correlated better with respirable lead concentration (r2 = 0.35, P = 0.0001) than with PbA concentration and had a higher slope coefficient. Controlling for respirable lead concentration reduced the partial correlation coefficient between PbA concentration and PbB level from 0.56 to 0.20 (P = 0.053). The results indicate that the contribution of respirable lead particles to lead absorption would be greater than that of PbA. This study concludes that the measurement of PbA only may not properly reflect a worker's exposure to lead particles with diverse characteristics. For the evaluation of a worker's exposure to various types of lead particles, it is recommended that respirable lead particles as well as PbA be measured.

Childhood Lead Exposure from Battery Recycling in Vietnam

Directory of Open Access Journals (Sweden)

William E. Daniell

2015-01-01

Full Text Available Background. Battery recycling facilities in developing countries can cause community lead exposure. Objective. To evaluate child lead exposure in a Vietnam battery recycling craft village after efforts to shift home-based recycling outside the village. Methods. This cross-sectional study evaluated 109 children in Dong Mai village, using blood lead level (BLL measurement, parent interview, and household observation. Blood samples were analyzed with a LeadCare II field instrument; highest BLLs (≥45 μg/dL were retested by laboratory analysis. Surface and soil lead were measured at 11 households and a school with X-ray fluorescence analyzer. Results. All children had high BLLs; 28% had BLL ≥45 μg/dL. Younger age, family recycling, and outside brick surfaces were associated with higher BLL. Surface and soil lead levels were high at all tested homes, even with no recycling history. Laboratory BLLs were lower than LeadCare BLLs, in 24 retested children. Discussion. In spite of improvements, lead exposure was still substantial and probably associated with continued home-based recycling, legacy contamination, and workplace take-home exposure pathways. There is a need for effective strategies to manage lead exposure from battery recycling in craft villages. These reported BLL values should be interpreted cautiously, although the observed field-laboratory discordance may reflect bias in laboratory results.

Comparison of lead removal behaviors and generation of water-soluble sodium compounds in molten lead glass under a reductive atmosphere

Science.gov (United States)

Okada, Takashi; Nishimura, Fumihiro; Xu, Zhanglian; Yonezawa, Susumu

2018-06-01

We propose a method of reduction-melting at 1000 °C, using a sodium-based flux, to recover lead from cathode-ray tube funnel glass. To recover the added sodium from the treated glass, we combined a reduction-melting process with a subsequent annealing step at 700 °C, generating water-soluble sodium compounds in the molten glass. Using this combined process, this study compares lead removal behavior and the generation of water-soluble sodium compounds (sodium silicates and carbonates) in order to gain fundamental information to enhance the recovery of both lead and sodium. We find that lead removal increases with increasing melting time, whereas the generation efficiency of water-soluble sodium increases and decreases periodically. In particular, near 90% lead removal, the generation of water-soluble sodium compounds decreased sharply, increasing again with the prolongation of melting time. This is due to the different crystallization and phase separation efficiencies of water-soluble sodium in molten glass, whose structure continuously changes with lead removal. Previous studies used a melting time of 60 min in the processes. However, in this study, we observe that a melting time of 180 min enhances the water-soluble sodium generation efficiency.

Studies on mathematical modeling of the leaching process in order to efficiently recover lead from the sulfate/oxide lead paste.

Science.gov (United States)

Buzatu, Traian; Ghica, Gabriel Valeriu; Petrescu, Ionuţ Mircea; Iacob, Gheorghe; Buzatu, Mihai; Niculescu, Florentina

2017-02-01

Increasing global lead consumption has been mainly supported by the acid battery manufacturing industry. As the lead demand will continue to grow, to provide the necessary lead will require an efficient approach to recycling lead acid batteries. In this paper was performed a mathematical modeling of the process parameters for lead recovery from spent lead-acid batteries. The results of the mathematical modeling compare well with the experimental data. The experimental method applied consists in the solubilisation of the sulfate/oxide paste with sodium hydroxide solutions followed by electrolytic processing for lead recovery. The parameters taken into considerations were NaOH molarity (4M, 6M and 8M), solid/liquid ratio - S/L (1/10, 1/30 and 1/50) and temperature (40°C, 60°C and 80°C). The optimal conditions resulted by mathematical modeling of the electrolytic process of lead deposition from alkaline solutions have been established by using a second-order orthogonal program, in order to obtain a maximum efficiency of current without exceeding an imposed energy specific consumption. The optimum value for the leaching recovery efficiency, obtained through mathematical modeling, was 89.647%, with an error of δ y =3.623 which leads to a maximum recovery efficiency of 86.024%. The optimum values for each variable that ensure the lead extraction efficiency equal to 89.647% are the following: 3M - NaOH, 1/35 - S/L, 70°C - temperature. Copyright © 2016 Elsevier Ltd. All rights reserved.

Current leads cooling for the series-connected hybrid magnets

Science.gov (United States)

Bai, Hongyu; Marshall, William S.; Bird, Mark D.; Gavrilin, Andrew V.; Weijers, Hubertus W.

2014-01-01

Two Series-Connected Hybrid (SCH) magnets are being developed at the National High Magnetic Field Laboratory. Both SCH magnets combine a set of resistive Florida-Bitter coils with a superconducting outsert coil constructed of the cable-in-conduit conductor (CICC). The outsert coils of the two magnets employ 20 kA BSCCO HTS current leads for the power supply although they have different designs and cooling methods. The copper heat exchangers of the HTS current leads for the HZB SCH are cooled with forced flow helium at a supply temperature of 44 K, while the copper heat exchangers of HTS current leads for NHMFL SCH are cooled with liquid nitrogen at a temperature of 78 K in a self-demand boil-off mode. This paper presents the two cooling methods and their impacts on cryogenic systems. Their efficiencies and costs are compared and presented.

Method of analysis for the determination of lead and cadmium in fresh meat

NARCIS (Netherlands)

Ruig, de W.G.

1980-01-01

This report comprises the result of the RIKILT of an intercomparison on the determination of lead and cadmium in bovine liver and bovine kidney. The aim of this round robbin was to check a wet ashing procedure followed by a flame AAS determination as described too in EEC doc. 2266/VI/77. Special

High-dose biotin therapy leading to false biochemical endocrine profiles: validation of a simple method to overcome biotin interference.

Science.gov (United States)

Piketty, Marie-Liesse; Prie, Dominique; Sedel, Frederic; Bernard, Delphine; Hercend, Claude; Chanson, Philippe; Souberbielle, Jean-Claude

2017-05-01

High-dose biotin therapy is beneficial in progressive multiple sclerosis (MS) and is expected to be adopted by a large number of patients. Biotin therapy leads to analytical interference in many immunoassays that utilize streptavidin-biotin capture techniques, yielding skewed results that can mimic various endocrine disorders. We aimed at exploring this interference, to be able to remove biotin and avoid misleading results. We measured free triiodothyronine (fT3), free thyroxine (fT4), thyroid-stimulating hormone (TSH), parathyroid homrone (PTH), 25-hydroxyvitamin D (25OHD), follicle-stimulating hormone (FSH), luteinizing hormone (LH), prolactin, C-peptide, cortisol (Roche Diagnostics assays), biotin and its main metabolites (liquid chromatography tandem mass spectrometry) in 23 plasmas from MS patients and healthy volunteers receiving high-dose biotin, and in 39 biotin-unsupplemented patients, before and after a simple procedure (designated N5) designed to remove biotin by means of streptavidin-coated microparticles. We also assayed fT4, TSH and PTH in the 23 high-biotin plasmas using assays not employing streptavidin-biotin binding. The biotin concentration ranged from 31.7 to 1160 µg/L in the 23 high-biotin plasmas samples. After the N5 protocol, the biotin concentration was below the detection limit in all but two samples (8.3 and 27.6 μg/L). Most hormones results were abnormal, but normalized after N5. All results with the alternative methods were normal except two slight PTH elevations. In the 39 biotin-unsupplemented patients, the N5 protocol did not affect the results for any of the hormones, apart from an 8.4% decrease in PTH. We confirm that most streptavidin-biotin hormone immunoassays are affected by high biotin concentrations, leading to a risk of misdiagnosis. Our simple neutralization method efficiently suppresses biotin interference.

Lead levels - blood

Science.gov (United States)

Blood lead levels ... is used to screen people at risk for lead poisoning. This may include industrial workers and children ... also used to measure how well treatment for lead poisoning is working. Lead is common in the ...

Different partial volume correction methods lead to different conclusions

DEFF Research Database (Denmark)

Greve, Douglas N; Salat, David H; Bowen, Spencer L

2016-01-01

A cross-sectional group study of the effects of aging on brain metabolism as measured with (18)F-FDG-PET was performed using several different partial volume correction (PVC) methods: no correction (NoPVC), Meltzer (MZ), Müller-Gärtner (MG), and the symmetric geometric transfer matrix (SGTM) usin...

Lead and osteoporosis: Mobilization of lead from bone in postmenopausal women

Energy Technology Data Exchange (ETDEWEB)

Silbergeld, E.K. (Environmental Defense Fund, WA (USA)); Schwartz, J. (Environmental Protection Agency, Washington, DC (USA)); Mahaffey, K. (National Institute of Environmental Health Sciences, Research Triangle Park, NC (USA))

1988-10-01

Although it has been known that humans accumulate lead in bone, mineralized tissue has been considered primarily as a sequestering compartment and not as a site of toxic action for lead. However, experimental data indicate that bone lead can be released during conditions of demineralization, such as pregnancy and lactation. We have examined lead status in women, before and after menopause, using the NHANES II dataset compiled between 1976 and 1980. In 2981 black and white women there was a highly significant increase in both whole blood and calculated plasma lead concentrations after menopause. The results indicate that bone lead is not an inert storage site for absorbed lead. Moreover, lead may interact with other factors in the course of postmenopausal osteoporosis, to aggravate the course of the disease, since lead is known to inhibit activation of vitamin D, uptake of dietary calcium, and several regulatory aspects of bone cell function. The consequences of this mobilization may also be of importance in assessing the risks of maternal lead exposure to fetal and infant health.

MRI-induced heating of deep brain stimulation leads

International Nuclear Information System (INIS)

Mohsin, Syed A; Sheikh, Noor M; Saeed, Usman

2008-01-01

The radiofrequency (RF) field used in magnetic resonance imaging is scattered by medical implants. The scattered field of a deep brain stimulation lead can be very intense near the electrodes stimulating the brain. The effect is more pronounced if the lead behaves as a resonant antenna. In this paper, we examine the resonant length effect. We also use the finite element method to compute the near field for (i) the lead immersed in inhomogeneous tissue (fat, muscle, and brain tissues) and (ii) the lead connected to an implantable pulse generator. Electric field, specific absorption rate and induced temperature rise distributions have been obtained in the brain tissue surrounding the electrodes. The worst-case scenario has been evaluated by neglecting the effect of blood perfusion. The computed values are in good agreement with in vitro measurements made in the laboratory.

Safe leads and lead changes in competitive team sports

Science.gov (United States)

Clauset, A.; Kogan, M.; Redner, S.

2015-06-01

We investigate the time evolution of lead changes within individual games of competitive team sports. Exploiting ideas from the theory of random walks, the number of lead changes within a single game follows a Gaussian distribution. We show that the probability that the last lead change and the time of the largest lead size are governed by the same arcsine law, a bimodal distribution that diverges at the start and at the end of the game. We also determine the probability that a given lead is "safe" as a function of its size L and game time t . Our predictions generally agree with comprehensive data on more than 1.25 million scoring events in roughly 40 000 games across four professional or semiprofessional team sports, and are more accurate than popular heuristics currently used in sports analytics.

Optical waveguides in fluoride lead silicate glasses fabricated by carbon ion implantation

Science.gov (United States)

Shen, Xiao-liang; Wang, Yue; Zhu, Qi-feng; Lü, Peng; Li, Wei-nan; Liu, Chun-xiao

2018-03-01

The carbon ion implantation with energy of 4.0 MeV and a dose of 4.0×1014 ions/cm2 is employed for fabricating the optical waveguide in fluoride lead silicate glasses. The optical modes as well as the effective refractive indices are measured by the prism coupling method. The refractive index distribution in the fluoride lead silicate glass waveguide is simulated by the reflectivity calculation method (RCM). The light intensity profile and the energy losses are calculated by the finite-difference beam propagation method (FD-BPM) and the program of stopping and range of ions in matter (SRIM), respectively. The propagation properties indicate that the C2+ ion-implanted fluoride lead silicate glass waveguide is a candidate for fabricating optical devices.

Some studies of maternal and infant lead exposure in Glasgow

Energy Technology Data Exchange (ETDEWEB)

Moore, M.R.; Goldberg, A.; Pocock, S.J.; Meredith, A.; Stewart, I.M.; MacAnespie, H.; Lees, R.; Low, A.

1982-04-01

In two studies in the city of Glasgow, 236 mothers and their newly born infants and 117 mothers and their 6-weeks old children's environmental lead exposure were examined. In both studies blood lead concentrations were found to correlate significantly with the cube root of the domestic water lead concentrations. In the first study, multiple regression analyses of maternal blood lead and cord blood lead concentrations on other variables showed a significant negative correlation with gestational age. It was also noted that there was an annual fluctuation in maternal blood lead concentration with highest values in the autumn. In the second study, similar relationships were found. Although there was no association between blood lead and sex, age, place of birth or feeding method, as in the previous study, a significant association between social class and blood lead was found. This could be explained on the basis of the significant correlation between water lead and social class. In those mothers who breast fed, breast milk lead concentrations were found to correlate significantly with blood lead concentrations where breast milk lead was around one tenth of blood lead concentration. These studies emphasise the importance of water lead in the economy of environmental lead exposure to mothers and their unborn and newly born infants.

Lead isotope measurements on aerosol samples with ICP-MS

International Nuclear Information System (INIS)

Widmer, C.R.; Kraehenbuehl, U.; Kramers, J.; Tobler, L.

2000-01-01

Size fractionated aerosols were collected with low pressure Berner impactors on a radio/TV tower 110 m above ground on a hill 10 km east of Bern at a total elevation of 1060 m asl. Two different wind sectors were chosen with the goal of assessing any differences in lead concentration and the 3 radiogenic lead isotopes (206,207,208) for east and west wind, respectively. A leaching technique was used to extract the lead quantitatively from the surface of the impaction foils. This method has been proven to be better suited for airborne particles than complete microwave digestion because it is less time consuming and contamination risk is smaller. Blank considerations played a major role in choosing all the chemicals, tubes, beakers and selecting the analytical method. Lead concentrations were determined with GF-AAS and lead isotopes with two different ICP-MS systems, one being a multicollector system. Precision of the simultaneous multicollector system was found to be at least a factor of 3 better than that of the sequentially operating ICP-MS. The small variations in isotope ratios from the two wind sectors can be distinctly seen with this enhanced precision. The observed relative difference in isotope ratios between east- and westwind was ∝0.6% for 207 Pb/ 206 Pb and ∝0.5% for 208 Pb/ 206 Pb. (orig.)

Possible Lead Free Nanocomposite Dielectrics for High Energy Storage Applications

Directory of Open Access Journals (Sweden)

Srinivas Kurpati

2017-03-01

Full Text Available There is an increasing demand to improve the energy density of dielectric capacitors for satisfying the next generation material systems. One effective approach is to embed high dielectric constant inclusions such as lead zirconia titanate in polymer matrix. However, with the increasing concerns on environmental safety and biocompatibility, the need to expel lead (Pb from modern electronics has been receiving more attention. Using high aspect ratio dielectric inclusions such as nanowires could lead to further enhancement of energy density. Therefore, the present brief review work focuses on the feasibility of development of a lead-free nanowire reinforced polymer matrix capacitor for energy storage application. It is expected that Lead-free sodium Niobate nanowires (NaNbO3 and Boron nitride will be a future candidate to be synthesized using simple hydrothermal method, followed by mixing them with polyvinylidene fluoride (PVDF/ divinyl tetramethyl disiloxanebis (benzocyclobutene matrix using a solution-casting method for Nanocomposites fabrication. The energy density of NaNbO3 and BN based composites are also be compared with that of lead-containing (PbTiO3/PVDF Nano composites to show the feasibility of replacing lead-containing materials from high-energy density dielectric capacitors. Further, this paper explores the feasibility of these materials for space applications because of high energy storage capacity, more flexibility and high operating temperatures. This paper is very much useful researchers who would like to work on polymer nanocomposites for high energy storage applications.

Childhood lead exposure in France: benefit estimation and partial cost-benefit analysis of lead hazard control

Directory of Open Access Journals (Sweden)

Zmirou-Navier Denis

2011-05-01

Full Text Available Abstract Background Lead exposure remains a public health concern due to its serious adverse effects, such as cognitive and behavioral impairment: children younger than six years of age being the most vulnerable population. In Europe, the lead-related economic impacts have not been examined in detail. We estimate the annual costs in France due to childhood exposure and, through a cost benefit analysis (CBA, aim to assess the expected social and economic benefits of exposure abatement. Methods Monetary benefits were assessed in terms of avoided national costs. We used results from a 2008 survey on blood-lead (B-Pb concentrations in French children aged one to six years old. Given the absence of a threshold concentration being established, we performed a sensitivity analysis assuming different hypothetical threshold values for toxicity above 15 μg/L, 24 μg/L and 100 μg/L. Adverse health outcomes of lead exposure were translated into social burden and economic costs based on literature data from literature. Direct health benefits, social benefits and intangible avoided costs were included. Costs of pollutant exposure control were partially estimated in regard to homes lead-based paint decontamination, investments aiming at reducing industrial lead emissions and removal of all lead drinking water pipes. Results The following overall annual benefits for the three hypothetical thresholds values in 2008 are: €22.72 billion, €10.72 billion and €0.44 billion, respectively. Costs from abatement ranged from €0.9 billion to 2.95 billion/year. Finally, from a partial CBA of lead control in soils and dust the estimates of total net benefits were € 3.78 billion, € 1.88 billion and €0.25 billion respectively for the three hypothesized B-Pb effect values. Conclusions Prevention of childhood lead exposure has a high social benefit, due to reduction of B-Pb concentrations to levels below 15 μg/L or 24 μg/L, respectively. Reducing only exposures

Radiography of Co-60 in the lead cube castings

International Nuclear Information System (INIS)

Djoli Soembogo; Harun Al Rasyid R; Namad Sianta

2016-01-01

Radiography Co-60 on Carbon steel or Stainless steel has been widely applied, but for metal Lead has not yet been applied and has not yet widely known. Lead has a greater density than Carbon steel or Stainless steel and could muffle gamma radiation so it takes a longer exposure time. The result of its film radiography are also not as good as compared to radiography applications on carbon steel or Stainless steel. The study also applied digital radiography using isotope Co-60 sources and used Epson V700 scanner positive film for digitization results of conventional radiographic films. These radiographs using film AGFA D7 to get the contrast medium, medium sensitivity and good image quality. The purpose of radiography Co-60 on the cube castings Lead is to find indications of defective castings cube Lead and digitizing the results using conventional radiographic film with a positive film media scanner to process the data transfer and storage of digital data. Radiographic testing has been carried out using the isotope Co-60 on metal castings Lead with a single thickness of a single shadow method using positive film scanner media and isotope Co-60 with disabilities observation parameter Lead metal castings on radiographic film. Co-60 radiation time exposure is 3,500 hours for the thickness of the metal cube castings Lead 100 mm with the activity of 29 Ci and perpendicular SFD of 840 mm. Radiographic testing on metal cube castings Lead by the method of a single thickness of single image defects produce a parameter indicative for a cube of metal castings Lead of porosity level 2. The density mean of radiographic film was 2.051 and 2.046 for 5 minutes in a developer solution. The result of scanning positive film is in the form of digital radiography which allows for the transfer of digital data or computerized storage of digital data. This status is still within limits acceptable under the standards referred. (author)

[Environmental lead poisoning from lead-glazed earthenware used for storing drinks].

Science.gov (United States)

Sabouraud, S; Coppéré, B; Rousseau, C; Testud, F; Pulce, C; Tholly, F; Blanc, M; Culoma, F; Facchin, A; Ninet, J; Chambon, P; Medina, B; Descotes, J

2009-12-01

Current unusual environmental sources of lead exposure mainly include traditional medicines, either ayurvedic remedies or others, traditional cosmetics (kohl, surma), and the use of traditional earthenware, for storage or cooking. We report two cases of lead poisoning in adults initially identified by paroxysmal abdominal pain or anemia. In both cases, the environmental investigation evidenced one main source of lead exposure, namely a lead-glazed earthenware jug in which a drink was stored, "kefir" in the first case, and "kombucha" tea in the second one. It is recommended to search for lead intoxication in patients with unexplained anemia. Environmental sources of lead can be multiple. Their relative importance has to be ranked during the environmental investigation and among these, lead-glazed earthenware must be considered as a source of high lead exposure when drinks are stored inside and thus can soak.

Radioisotope examination of kidney function in lead intoxication

International Nuclear Information System (INIS)

Klimentova, G.; Buchancova, J.; Galikova, E.; Lepej, J.

1982-01-01

The renal function was assessed of 12 patients with professional lead intoxication by radioisotope examination methods. In six patients changes on the radionephrographic curve were observed, showing flattening and shift of the peak of the curve, and prolongation of the secretory and excretory phases. The phase scintiscan displayed a slowed down uptake of the radioactive substance and pathological persistance of activity in the kidneys. The impairment of renal functions proved to be reversible. The authors consider rad+oisotope examinations to be an appropriate approach permitting evaluation of renal functions during lead intoxication, as well as helping to assess the deployment of persons who had suffered from intoxication, to workplaces where there is danger of exposure to lead. (author)

Urban gardens: lead exposure, recontamination mechanisms, and implications for remediation design.

Science.gov (United States)

Clark, Heather F; Hausladen, Debra M; Brabander, Daniel J

2008-07-01

Environmental lead contamination is prevalent in urban areas where soil represents a significant sink and pathway of exposure. This study characterizes the speciation of lead that is relevant to local recontamination and to human exposure in the backyard gardens of Roxbury and Dorchester, MA, USA. One hundred forty-one backyard gardens were tested by X-ray fluorescence, and 81% of gardens have lead levels above the US EPA action limit of 400 microg/g. Raised gardening beds are the in situ exposure reduction method used in the communities to promote urban gardening. Raised beds were tested for lead and the results showed that the lead concentration increased from an initial range of 150+/-40 microg/g to an average of 336 microg/g over 4 years. The percent distribution of lead in the fine grain soil (lead, and the trace metal signature of the fine grain soil in both gardens and raised gardening beds is characteristic of lead-based paint. This study demonstrates that raised beds are a limited exposure reduction method and require maintenance to achieve exposure reduction goals. An exposure model was developed based on a suite of parameters that combine relevant values from the literature with site-specific quantification of exposure pathways. This model suggests that consumption of homegrown produce accounts for only 3% of children's daily exposure of lead while ingestion of fine grained soil (lead remediation on a yard-by-yard scale requires constant maintenance and that remediation may need to occur on a neighborhood-wide scale.

Exposure to lead in South African shooting ranges

International Nuclear Information System (INIS)

Mathee, Angela; Jager, Pieter de; Naidoo, Shan; Naicker, Nisha

2017-01-01

Introduction: Lead exposure in shooting ranges has been under scrutiny for decades, but no information in this regard is available in respect of African settings, and in South Africa specifically. The aim of this study was to determine the blood lead levels in the users of randomly selected private shooting ranges in South Africa's Gauteng province. Methods: An analytical cross sectional study was conducted, with participants recruited from four randomly selected shooting ranges and three archery ranges as a comparator group. Results: A total of 118 (87 shooters and 31 archers) were included in the analysis. Shooters had significantly higher blood lead levels (BLL) compared to archers with 36/85 (42.4%) of shooters versus 2/34 (5.9%) of archers found to have a BLL ≥10 μg/dl (p<0.001). Conclusion: Shooting ranges may constitute an import site of elevated exposure to lead. Improved ventilation, low levels of awareness of lead hazards, poor housekeeping, and inadequate personal hygiene facilities and practices at South African shooting ranges need urgent attention. - Highlights: • This is the first study, to our knowledge, of lead exposure in shooting ranges in an African setting. • This study indicates highly elevated lead exposure amongst the users of certain private shooting ranges in South Africa. • Lead exposure may be a serious, yet under-studied, source of adult lead exposure in South Africa, and possibly elsewhere on the African continent.

Exposure to lead in South African shooting ranges

Energy Technology Data Exchange (ETDEWEB)

Mathee, Angela [South African Medical Research Council, Environment & Health Research Unit, PO Box 87373, Houghton 2041 (South Africa); University of the Witwatersrand (School of Public Health), PO Box Wits, Johannesburg 2050 (South Africa); University of Johannesburg (Environmental Health Department, Faculty of Health Sciences), PO Box 524, Auckland Park, Johannesburg 2006 (South Africa); Jager, Pieter de [University of the Witwatersrand (School of Public Health), PO Box Wits, Johannesburg 2050 (South Africa); National Health Laboratory Service (Epidemiology and Surveillance Unit, National Institute for Occupational Health), PO Box 4788, Johannesburg 2000 (South Africa); Naidoo, Shan [University of the Witwatersrand (School of Public Health), PO Box Wits, Johannesburg 2050 (South Africa); Naicker, Nisha [South African Medical Research Council, Environment & Health Research Unit, PO Box 87373, Houghton 2041 (South Africa); University of the Witwatersrand, School of Public Health, PO Box Wits, Johannesburg 2050 (South Africa); University of Johannesburg, Environmental Health Department, Faculty of Health Sciences, PO Box 524, Auckland Park, Johannesburg 2006 (South Africa)

2017-02-15

Introduction: Lead exposure in shooting ranges has been under scrutiny for decades, but no information in this regard is available in respect of African settings, and in South Africa specifically. The aim of this study was to determine the blood lead levels in the users of randomly selected private shooting ranges in South Africa's Gauteng province. Methods: An analytical cross sectional study was conducted, with participants recruited from four randomly selected shooting ranges and three archery ranges as a comparator group. Results: A total of 118 (87 shooters and 31 archers) were included in the analysis. Shooters had significantly higher blood lead levels (BLL) compared to archers with 36/85 (42.4%) of shooters versus 2/34 (5.9%) of archers found to have a BLL ≥10 μg/dl (p<0.001). Conclusion: Shooting ranges may constitute an import site of elevated exposure to lead. Improved ventilation, low levels of awareness of lead hazards, poor housekeeping, and inadequate personal hygiene facilities and practices at South African shooting ranges need urgent attention. - Highlights: • This is the first study, to our knowledge, of lead exposure in shooting ranges in an African setting. • This study indicates highly elevated lead exposure amongst the users of certain private shooting ranges in South Africa. • Lead exposure may be a serious, yet under-studied, source of adult lead exposure in South Africa, and possibly elsewhere on the African continent.

Effect measure modification of blood lead-air lead slope factors.

Science.gov (United States)

Richmond-Bryant, Jennifer; Meng, Qingyu; Cohen, Jonathan; Davis, J Allen; Svendsgaard, David; Brown, James S; Tuttle, Lauren; Hubbard, Heidi; Rice, Joann; Kirrane, Ellen; Vinikoor-Imler, Lisa; Kotchmar, Dennis; Hines, Erin; Ross, Mary

2015-01-01

There is abundant literature finding that susceptibility factors, including race and ethnicity, age, and housing, directly influence blood lead levels. No study has explored how susceptibility factors influence the blood lead-air lead relationship nationally. The objective is to evaluate whether susceptibility factors act as effect measure modifiers on the blood lead-air lead relationship. Participant level blood lead data from the 1999 to 2008 National Health and Nutrition Examination Survey were merged with air lead data from the US Environmental Protection Agency. Linear mixed effects models were run with and without an air lead interaction term for age group, sex, housing age, or race/ethnicity to determine whether these factors are effect measure modifiers for all ages combined and for five age brackets. Age group and race/ethnicity were determined to be effect measure modifiers in the all-age model and for some age groups. Being a child (1-5, 6-11, and 12-19 years) or of Mexican-American ethnicity increased the effect estimate. Living in older housing (built before 1950) decreased the effect estimate for all models except for the 1-5-year group, where older housing was an effect measure modifier. These results are consistent with the peer-reviewed literature of time-activity patterns, ventilation, and toxicokinetics.

Serum Neuron-Specific Enolase, Biogenic Amino-Acids and Neurobehavioral Function in Lead-Exposed Workers from Lead-Acid Battery Manufacturing Process

Directory of Open Access Journals (Sweden)

K Ravibabu

2015-01-01

Full Text Available Background: The interaction between serum neuron-specific enolase (NSE, biogenic amino-acids and neurobehavioral function with blood lead levels in workers exposed to lead form lead-acid battery manufacturing process was not studied. Objective: To evaluate serum NSE and biogenic amino-acids (dopamine and serotonin levels, and neurobehavioral performance among workers exposed to lead from lead-acid storage battery plant, and its relation with blood lead levels (BLLs. Methods: In a cross-sectional study, we performed biochemical and neurobehavioral function tests on 146 workers exposed to lead from lead-acid battery manufacturing process. BLLs were assessed by an atomic absorption spectrophotometer. Serum NSE, dopamine and serotonin were measured by ELISA. Neurobehavioral functions were assessed by CDC-recommended tests—simple reaction time (SRT, symbol digit substitution test (SDST, and serial digit learning test (SDLT. Results: There was a significant correlation (r 0.199, p<0.05 between SDST and BLL. SDLT and SRT had also a significant positive correlation (r 0.238, p<0.01. NSE had a negative correlation (r –0.194, p<0.05 with serotonin level. Multiple linear regression analysis revealed that both SRT and SDST had positive significant associations with BLL. SRT also had a positive significant association with age. Conclusion: Serum NSE cannot be used as a marker for BLL. The only domain of neurobehavioral function tests that is affected by increased BLL in workers of lead-acid battery manufacturing process is that of the “attention and perception” (SDST.

Lead - nutritional considerations

Science.gov (United States)

... billion people had toxic (poisonous) blood lead levels. Food Sources Lead can be found in canned goods if there is lead solder in the ... to bottled water for drinking and cooking. Avoid canned goods from foreign ... cans goes into effect. If imported wine containers have a lead foil ...

Adsorption of lead onto smectite from aqueous solution.

Science.gov (United States)

Mhamdi, M; Galai, H; Mnasri, N; Elaloui, E; Trabelsi-Ayadi, M

2013-03-01

The purpose of this research is to study the effect of a new method of adsorption using membrane filtration to determine the maximum amount of lead adsorbed by clay and investigate the behavior of the clay after adsorption of the said metal. Treatment of wastewater contaminated with heavy metals depends on the characteristics of the effluent, the amount of final discharge, the cost of treatment, and the compatibility of the treatment process. The process of adsorption of heavy metals by clays may be a simple, selective, and economically viable alternative to the conventional physical-chemical treatment. This is justified by the importance of the surface developed by this material, the presence of negative charges on the said surface, the possibility of ion exchange taking place, and its wide availability in nature. The removal of lead from wastewater was studied by using the adsorption technique and using clay as the adsorbent. A method was optimized for adsorption through a membrane approaching natural adsorption. This new method is simple, selective, and the lead adsorption time is about 3 days. The various properties of clay were determined. It was observed that the cation exchange capacity of the clay was 56 meq/100 g of hydrated clay for the raw sample and 82 meq/100 g for the purified sample. The total surface area determined by the methylene blue method was equal to 556 and 783 m(2)/g for the raw and purified samples, respectively. The adsorption kinetics depends on several parameters. The Pb(II) clay, obeys the Langmuir, Freundlich, and the Elovich adsorption isotherms with high regression coefficients. The use of this adsorbent notably decreases the cost of treatment. It was concluded that clay shows a strong adsorption capacity on Pb(II), the maximum interaction occurring with purified clay treated at high concentration of lead. It is proposed that this adsorption through a membrane be extended for the treatment of effluents containing other metals.

Factors affecting the simultaneous determination of copper, lead, cadmium, and zinc concentrations in human head hair using differential pulse anodic stripping voltammetry method

International Nuclear Information System (INIS)

Wandiga, S.O.; Jumba, I.O.

1982-01-01

Conditions of analysis of copper, lead, cadmium and zinc content in human hair using differential pulse anodic stripping voltammetry (DPASV) and hanging mercury drop electrode (HMDE) have been established. Sample digestion using using the mixture HCI; H 2 O 2 ;HNO 3 in the ratio 2:1:40 by volume gave the best wet-ashing procedure. The peak currents and peak potentials of zinc, cadmium and lead, copper were maximum at pH 6-7 and 1-3 respectively, when excess H 2 O 2 was eliminated with subsequent addition of hydroxyamine hydrochloride. Matrix concentration effects were minimized by digesting weights not exceeding 50 mg per sample. The effect of selenium (IV) was negligible and was ignored. The detection limit of 0.0036 ng/cm 3 for Cd + 2 was obtained while the values for zinc, lead and copper were 0.0230, 0.0287 and 0.0269 ng/cm 3 respectively at the 95% confidence limit. The observed DPASV condition of analysis of these metals are useful for routine determination of the metals in human hair and should complement the conventional flame absorption spectrophotometry method. (author)

Potentiometric stripping analysis of Cadmium and Lead in superficial waters

International Nuclear Information System (INIS)

Arias, Juan Miguel; Marciales Castiblanco, Clara

2003-01-01

This paper contains the implementation and validation of an analytical method for determining cadmium and lead in surface waters. This is a valuable tool for the description of actual conditions and qualitative and quantitative control of dangerous heavy metals discharge in water bodies. Test were run for selecting stripping potentiometry conditions that as indicated by results were: sample oxidant concentration 36.4 μg/L Hg 2+ stirring frequency 2400 rpm, electrolysis time 80 s., electrolysis potential -950 mV and pH of 2.0. Interference of Cu 2+ and Fe 2+ showed that copper concentrations larger than 150 μg/L and 500 μg/L negatively influence the analytical response for Cadmium and lead respectively; [Fe 3+ ] larger than 60 μg/L and 400 μg/L cause variations in cadmium and lead read content respectively. Linear concentration range for cadmium lies between 5 and 250 μg/L; for lead range goes from 10 to 250 μg/L. Precision expressed as repeatability for both system and method, exhibit good reproducibility with variation coefficients below 6%. Accuracy, assessed from recuperation, is strongly influenced by concentration level therefore standard addition is recommended for lead and cadmium quantification. Analysis performed on surface waters from Colombian Magdalena and Cauca rivers pointed lead and cadmium contents below detection limits

The refining of secondary lead for use in advanced lead-acid batteries

International Nuclear Information System (INIS)

Ellis, Timothy W.; Mirza, Abbas H.

2010-01-01

Secondary lead, i.e. material produced by the recycling of lead-acid batteries has become the primary source of lead in much of the world. This has been important to the secondary lead industry as other uses have dwindled, e.g. lead based pigments, chemicals, fuel additives, solders and CRT glasses. Presently, battery manufacturing accounts for greater than 80% of lead consumption while recycled lead accounts for approximately the same market share of lead supply. These two facts strongly demonstrate the battery manufacturing and recycled lead are intimately coupled in everyday life. In this paper we will explore how recycled lead has become the material of choice for battery construction through the development of a recovery and refining process that exceeds the industries requirements. Particular focus will be on addressing the results presented by Prengaman on the effects of contaminant or tramp elements on gassing in lead-acid batteries. (author)

A simple lead dust fall method predicts children's blood lead level: New evidence from Australia.

Science.gov (United States)

Gulson, Brian; Taylor, Alan

2017-11-01

We have measured dust fall accumulation in petri dishes (PDD) collected 6 monthly from inside residences in Sydney urban area, New South Wales, Australia as part of a 5-year longitudinal study to determine environmental associations, including soil. with blood lead (PbB) levels. The Pb loading in the dishes (n = 706) had geometric means (GM) of 24µg/m 2 /30d, a median value of 22µg/m 2 /30d with a range from 0.2 to 11,390µg/m 2 /30d. Observed geometric mean PbB was 2.4µg/dL at ages 2-3 years. Regression analyses showed a statistically significant relationship between predicted PbB and PDD. The predicted PbB values from dust in our study are consistent with similar analyses from the US in which floor dust was collected by wipes. Predicted PbB values from PDD indicate that an increase in PDD of about 100µg/m 2 /30d would increase PbB by about 1.5µg/dL or a doubling PbB at the low levels currently observed in many countries. Predicted PbB values from soil indicate that a change from 0 to 1000mg Pb/kg results in an increase of 1.7µg/dL in PbB, consistent with earlier investigations. Blood Pb levels can be predicted from dust fall accumulation (and soil) in cases where blood sampling is not always possible, especially in young children. Petri dish loading data could provide an alternative or complementary "action level" at about 100µg Pb/m 2 /30 days, similar to the suggested level of about 110µg Pb/m 2 for surface wipes, for use in monitoring activities such as housing rehabilitation, demolition or soil resuspension. Copyright © 2017 Elsevier Inc. All rights reserved.

The effect of lead-based paint hazard remediation on blood lead levels of lead poisoned children in New York City.

Science.gov (United States)

Leighton, Jessica; Klitzman, Susan; Sedlar, Slavenka; Matte, Thomas; Cohen, Neal L

2003-07-01

Despite the widespread use of lead paint hazard control for children with lead poisoning, few controlled studies that estimate the effect of such control on children's blood lead levels have been published. This retrospective follow-up study examined the effects of lead hazard remediation and its timing on the blood lead levels of lead-poisoned children. From the New York City child blood lead registry, 221 children were selected who had an initial blood lead level of 20-44 micro g/dL between 1 July 1994 and 31 December 1996; were 6 months to 6 years of age; had a report of a follow-up blood lead test between 10 and 14 months after the initial test; had a lead-based paint hazard identified in the primary dwelling unit prior to the 10- to 14-month follow-up blood lead test; had resided or spent time at only one address with an identified lead-based paint hazard; and were not chelated. The decline in geometric mean blood lead levels from baseline to 10-14 months later was compared for children whose homes were remediated and whose homes were not remediated during the follow-up period. Regardless of remediation, geometric mean blood lead levels declined significantly from 24.3 micro g/dL at the initial diagnosis to 12.3 micro g/dL at the 10- to 14-month follow-up blood lead test (Premediated the geometric mean blood lead levels declined 53% compared to 41% among the 75 children whose homes were not remediated by the follow-up blood lead test, a remediation effect of approximately 20% (Premediation effect was 11%, although it was no longer significant. Race was the only factor that appeared to confound the relationship: Black children had higher follow-up blood lead levels even after controlling for other factors, including the natural logarithm of the initial blood lead level. The effect of remediation appeared to be stronger for younger (10 to remediation (within less than 3 months) appeared to have greater declines in blood lead levels at the follow-up test than

Lead Your Boss The Subtle Art of Managing Up

CERN Document Server

Baldoni, John

2009-01-01

Every manager on the move wants to have influence at the top in order to get his or her ideas heard and ultimately acted upon. In Lead Your Boss, recognized leadership guru John Baldoni gives managers new—as well as tried-and-true— methods for influencing both their bosses and their peers, and giving senior leaders reasons to follow their lead. Featuring instructive stories based on real-life experiences from leaders at all levels, Lead Your Boss reveals proven strategies for: • Developing spheres of influence • Handling tough issues • Asserting oneself diplomatically • Putting the team first

Comparison between Clinically Used Irregular Fields Shielded by Cerrobend and Standard Lead Blocks

Directory of Open Access Journals (Sweden)

Farajollahi A. R.

2015-06-01

Full Text Available Introduction: In radiation therapy centers across Iran, protection of normal tissues is usually accomplished by either Cerrobend or lead block shielding. In this study, the influence of these two shielding methods on central axis dose distribution of photon beam a Cobalt unit was investigated in clinical conditions. Materials and Methods: All measurements were performed for 60Co γ-ray beams and the Cerrobend blocks were fabricated by commercial Cerrobend materials. Standard lead block shields belonged to Cobalt unit. Data was collected through a calibrated ionization chamber, relative dosimetry systems and a TLD dosimetery. Results: Results of the percent depth dose (PDD measurements at depths of 0.5, 1, 5, 10, 15 and 20 cm for 23 different field sizes of patients with head and neck cancer showed no significant differences between lead and Cerrobend shielding methods. Measurement results of absolute dosimetry in depths of 1.5, 3, 5, 7, 10 and 12 cm also showed no significant differences between these two shielding methods. The same results were obtained by TLD dosimetry on patient skin. Conclusion: Use of melt shielding methods is a very easy and fast shield-making technique with no differences in PDD, absolute and skin dose between lead and Cerrobend block shielding methods.

HAMS: High-Affinity Mass Spectrometry Screening. A High-Throughput Screening Method for Identifying the Tightest-Binding Lead Compounds for Target Proteins with No False Positive Identifications.

Science.gov (United States)

Imaduwage, Kasun P; Go, Eden P; Zhu, Zhikai; Desaire, Heather

2016-11-01

A major challenge in drug discovery is the identification of high affinity lead compounds that bind a particular target protein; these leads are typically identified by high throughput screens. Mass spectrometry has become a detection method of choice in drug screening assays because the target and the ligand need not be modified. Label-free assays are advantageous because they can be developed more rapidly than assays requiring labels, and they eliminate the risk of the label interfering with the binding event. However, in commonly used MS-based screening methods, detection of false positives is a major challenge. Here, we describe a detection strategy designed to eliminate false positives. In this approach, the protein and the ligands are incubated together, and the non-binders are separated for detection. Hits (protein binders) are not detectable by MS after incubation with the protein, but readily identifiable by MS when the target protein is not present in the incubation media. The assay was demonstrated using three different proteins and hundreds of non-inhibitors; no false positive hits were identified in any experiment. The assay can be tuned to select for ligands of a particular binding affinity by varying the quantity of protein used and the immobilization method. As examples, the method selectively detected inhibitors that have K i values of 0.2 μM, 50 pM, and 700 pM. These findings demonstrate that the approach described here compares favorably with traditional MS-based screening methods. Graphical Abstract ᅟ.

Leading education professionals: Local, connected, and artful

NARCIS (Netherlands)

Bathurst, R.; van Gelderen, M.W.

2014-01-01

In this paper, we explore the work life of a scholar new to academia in her methods of leading informally. We discuss five vignettes that offer moments of learning and reflection, including reducing performance anxiety, privileging financial accountability, the rise of the virtual world, the impact

Electronic and optical properties of lead iodide

DEFF Research Database (Denmark)

Ahuja, R.; Arwin, H.; Ferreira da Silva, A.

2002-01-01

The electronic properties and the optical absorption of lead iodide (PbI2) have been investigated experimentally by means of optical absorption and spectroscopic ellipsometry, and theoretically by a full-potential linear muffin-tin-orbital method. PbI2 has been recognized as a very promising...

Deaths: Leading Causes for 2015.

Science.gov (United States)

Heron, Melonie

2017-11-01

Objectives-This report presents final 2015 data on the 10 leading causes of death in the United States by age, sex, race, and Hispanic origin. Leading causes of infant, neonatal, and postneonatal death are also presented. This report supplements "Deaths: Final Data for 2015," the National Center for Health Statistics' annual report of final mortality statistics. Methods-Data in this report are based on information from all death certificates filed in the 50 states and the District of Columbia in 2015. Causes of death classified by the International Classification of Diseases, Tenth Revision (ICD-10) are ranked according to the number of deaths assigned to rankable causes. Cause-of-death statistics are based on the underlying cause of death. Results-In 2015, the 10 leading causes of death were, in rank order: Diseases of heart; Malignant neoplasms; Chronic lower respiratory diseases; Accidents (unintentional injuries); Cerebrovascular diseases; Alzheimer's disease; Diabetes mellitus; Influenza and pneumonia; Nephritis, nephrotic syndrome and nephrosis; and Intentional self-harm (suicide). They accounted for 74% of all deaths occurring in the United States. Differences in the rankings are evident by age, sex, race, and Hispanic origin. Leading causes of infant death for 2015 were, in rank order: Congenital malformations, deformations and chromosomal abnormalities; Disorders related to short gestation and low birth weight, not elsewhere classified; Sudden infant death syndrome; Newborn affected by maternal complications of pregnancy; Accidents (unintentional injuries); Newborn affected by complications of placenta, cord and membranes; Bacterial sepsis of newborn; Respiratory distress of newborn; Diseases of the circulatory system; and Neonatal hemorrhage. Important variations in the leading causes of infant death are noted for the neonatal and postneonatal periods. All material appearing in this report is in the public domain and may be reproduced or copied without

Melatonin reduces lead levels in blood, brain and bone and increases lead excretion in rats subjected to subacute lead treatment.

Science.gov (United States)

Hernández-Plata, Everardo; Quiroz-Compeán, Fátima; Ramírez-Garcia, Gonzalo; Barrientos, Eunice Yáñez; Rodríguez-Morales, Nadia M; Flores, Alberto; Wrobel, Katarzina; Wrobel, Kazimierz; Méndez, Isabel; Díaz-Muñoz, Mauricio; Robles, Juvencio; Martínez-Alfaro, Minerva

2015-03-04

Melatonin, a hormone known for its effects on free radical scavenging and antioxidant activity, can reduce lead toxicity in vivo and in vitro.We examined the effects of melatonin on lead bio-distribution. Rats were intraperitoneally injected with lead acetate (10, 15 or 20mg/kg/day) with or without melatonin (10mg/kg/day) daily for 10 days. In rats intoxicated with the highest lead doses, those treated with melatonin had lower lead levels in blood and higher levels in urine and feces than those treated with lead alone, suggesting that melatonin increases lead excretion. To explore the mechanism underlying this effect, we first assessed whether lead/melatonin complexes were formed directly. Electronic density functional (DFT) calculations showed that a lead/melatonin complex is energetically feasible; however, UV spectroscopy and NMR analysis showed no evidence of such complexes. Next, we examined the liver mRNA levels of metallothioneins (MT) 1 and 2. Melatonin cotreatment increased the MT2 mRNA expression in the liver of rats that received the highest doses of lead. The potential effects of MTs on the tissue distribution and excretion of lead are not well understood. This is the first report to suggest that melatonin directly affects lead levels in organisms exposed to subacute lead intoxication. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Surface dust wipes are the best predictors of blood leads in young children with elevated blood lead levels

Energy Technology Data Exchange (ETDEWEB)

Gulson, Brian, E-mail: brian.gulson@mq.edu.au [Graduate School of the Environment, Macquarie University, North Ryde NSW 2109 (Australia); CSIRO Earth Science and Resource Engineering, North Ryde NSW 2113 (Australia); Anderson, Phil [Information and Statistics Group, Australian Institute of Health and Welfare, Canberra ACT 2601 (Australia); Faculty of Health, University of Canberra, Canberra ACT 2601 (Australia); Taylor, Alan [Department of Psychology, Macquarie University, Sydney NSW 2109 (Australia)

2013-10-15

Background: As part of the only national survey of lead in Australian children, which was undertaken in 1996, lead isotopic and lead concentration measurements were obtained from children from 24 dwellings whose blood lead levels were ≥15 µg/dL in an attempt to determine the source(s) of their elevated blood lead. Comparisons were made with data for six children with lower blood lead levels (<10 µg/dL). Methods: Thermal ionisation and isotope dilution mass spectrometry were used to determine high precision lead isotopic ratios ({sup 208}Pb/{sup 206}Pb, {sup 207}Pb/{sup 206}Pb and {sup 206}Pb/{sup 204}Pb) and lead concentrations in blood, dust from floor wipes, soil, drinking water and paint (where available). Evaluation of associations between blood and the environmental samples was based on the analysis of individual cases, and Pearson correlations and multiple regression analyses based on the whole dataset. Results and discussion: The correlations showed an association for isotopic ratios in blood and wipes (r=0.52, 95% CI 0.19–0.74), blood and soil (r=0.33, 95% CI −0.05–0.62), and blood and paint (r=0.56, 95% CI 0.09–0.83). The regression analyses indicated that the only statistically significant relationship for blood isotopic ratios was with dust wipes (B=0.65, 95% CI 0.35–0.95); there were no significant associations for lead concentrations in blood and environmental samples. There is a strong isotopic correlation of soils and house dust (r=0.53, 95% CI 0.20–0.75) indicative of a common source(s) for lead in soil and house dust. In contrast, as with the regression analyses, no such association is present for bulk lead concentrations (r=−0.003, 95% CI −0.37–0.36), the most common approach employed in source investigations. In evaluation of the isotopic results on a case by case basis, the strongest associations were for dust wipes and blood. -- Highlights: • Children with elevated blood lead ≥15 µg/dL compared with a group with <10

Wafer scale lead zirconate titanate film preparation by sol-gel method using stress balance layer

International Nuclear Information System (INIS)

Lu Jian; Kobayashi, Takeshi; Yi Zhang; Maeda, Ryutaro; Mihara, Takashi

2006-01-01

In this paper, platinum/titanium (Pt/Ti) film was introduced as a residual stress balance layer into wafer scale thick lead zirconate titanate (PZT) film fabrication by sol-gel method. The stress developing in PZT film's bottom electrode as well as in PZT film itself during deposition were analyzed; the wafer curvatures, PZT crystallizations and PZT electric properties before and after using Pt/Ti stress balance layer were studied and compared. It was found that this layer is effective to balance the residual stress in PZT film's bottom electrode induced by thermal expansion coefficient mismatch and Ti diffusion, thus can notably reduce the curvature of 4-in. wafer from - 40.5 μm to - 12.9 μm after PZT film deposition. This stress balance layer was also found effective to avoid the PZT film cracking even when annealed by rapid thermal annealing with heating-rate up to 10.5 deg. C/s. According to X-ray diffraction analysis and electric properties characterization, crack-free uniform 1-μm-thick PZT film with preferred pervoskite (001) orientation, excellent dielectric constant, as high as 1310, and excellent remanent polarization, as high as 39.8 μC/cm 2 , can be obtained on 4-in. wafer

Lead elimination by ICRF 158 in rats after chronic lead exposure

Energy Technology Data Exchange (ETDEWEB)

Witting, U; Hultsch, E

1981-02-01

Lead elimination by ICRF 158, a lipophilic derivative of ethylene-diaminetetra-acetate (EDTA), was investigated in rats after chronic lead exposure. The animals had received a lead concentration of 550 ppm in their drinking water for 140 days. Subsequent treatment with ICRF 158 for 30 days led to increased mobilization and elimination of incorporated lead, and the lead-induced inhibition of hemosynthesis was removed. ICR 158 produced no renal damage in excess to lead-induced tubular nephrosis. Separate toxicity tests in mice demonstrated that is less toxic than CaNa/sub 2/EDTA. ICRF 158 does not form stable complexes with lead ions in vitro. The mechanism of action of this lipophilic EDTA derivative is compared to that of its hydrophilic correspondent, the chelating agent CaNa/sub 2/EDTA.

X-ray radiometric analysis of lead and zinc concentrates using germanium radiation detector

International Nuclear Information System (INIS)

Vajgachev, A.A.; Mamysh, V.A.; Mil'chakov, V.I.; Shchekin, K.I.; Berezkin, V.V.

1975-01-01

The results of determination of lead, zinc and iron in lead and zinc concentrates by the X-ray-radiometric method with the use of germanium semiconductor detector are presented. In the experiments the 57 Co source and tritium-zirconium target were used. The activity of 57 Co was 2 mc. The area of the germanium detector employed was 5g mm 2 , its thickness - 2.3 mm. In lead concentrates zinc and iron were determined from the direct intensity of K-series radiation. In the analysis of zinc concentrates the same conditions of recording and excitation were used as in the case of lead concentrates, but the measurements were conducted in saturated layers. It is demonstrated that the use of germanium semiconductor detectors in combination with the suggested methods of measurements makes it possible to perform determination of iron, zinc and lead in zinc and lead concentrates with permissible error

Cryogenic current leads

Energy Technology Data Exchange (ETDEWEB)

Zizek, F.

1982-01-01

Theoretical, technical and design questions are examined of cryogenic current leads for SP of magnetic systems. Simplified mathematical models are presented for the current leads. To illustrate modeling, the calculation is made of the real current leads for 500 A and three variants of current leads for 1500 A for the enterprise ''Shkoda.''

The effect of lead-based paint hazard remediation on blood lead levels of lead poisoned children in New York City

International Nuclear Information System (INIS)

Leighton, Jessica; Klitzman, Susan; Sedlar, Slavenka; Matte, Thomas; Cohen, Neal L.

2003-01-01

Despite the widespread use of lead paint hazard control for children with lead poisoning, few controlled studies that estimate the effect of such control on children's blood lead levels have been published. This retrospective follow-up study examined the effects of lead hazard remediation and its timing on the blood lead levels of lead-poisoned children. From the New York City child blood lead registry, 221 children were selected who had an initial blood lead level of 20-44 μg/dL between 1 July 1994 and 31 December 1996; were 6 months to 6 years of age; had a report of a follow-up blood lead test between 10 and 14 months after the initial test; had a lead-based paint hazard identified in the primary dwelling unit prior to the 10- to 14-month follow-up blood lead test; had resided or spent time at only one address with an identified lead-based paint hazard; and were not chelated. The decline in geometric mean blood lead levels from baseline to 10-14 months later was compared for children whose homes were remediated and whose homes were not remediated during the follow-up period. Regardless of remediation, geometric mean blood lead levels declined significantly from 24.3 μg/dL at the initial diagnosis to 12.3 μg/dL at the 10- to 14-month follow-up blood lead test (P<0.01). Among the 146 children whose homes were remediated the geometric mean blood lead levels declined 53% compared to 41% among the 75 children whose homes were not remediated by the follow-up blood lead test, a remediation effect of approximately 20% (P<0.01). After adjusting for potential confounders, the remediation effect was 11%, although it was no longer significant. Race was the only factor that appeared to confound the relationship: Black children had higher follow-up blood lead levels even after controlling for other factors, including the natural logarithm of the initial blood lead level. The effect of remediation appeared to be stronger for younger (10 to <36 months old) than for older (36

Work function of oxygen exposed lead and lead/indium alloy films

International Nuclear Information System (INIS)

Gundlach, K.H.; Hellemann, H.P.; Hoelzl, J.

1982-01-01

The effect of indium in superconducting tunnel junctions with lead/indium alloy base electrodes is investigated by measuring the vacuum work function of lead, indium, and lead/indium alloy films. It is found that the anomalous decrease of the work function of lead upon exposure to oxygen, explained by the penetration of oxygen into the inner surface of the lead film, is reversed into a slight increase in work function when some indium is added to the lead. This result indicates that the addition of indium provides a protection by suppressing the penetration of oxygen (and probably other gases) into the interior of the thin film

Determination of tellurium in lead and lead alloy using flow injection-hydride generation atomic absorption spectrometry

International Nuclear Information System (INIS)

Mesko, Marcia F.; Pozebon, Dirce; Flores, Erico M.M.; Dressler, Valderi L.

2004-01-01

A method based on flow injection-hydride generation atomic absorption spectrometry (FI-HG AAS) for the determination of trace amount of Te in lead and lead alloy is described. A flow injection system (FI) and related analytical parameters as well as Te determination and interference caused by Pb, Bi and Ag on Te were investigated. The Pb interference could be overcome by using a small sample volume, while the Bi interference could be overcome by thiourea. However, it was not possible to minimise the interference caused by Ag on Te. The optimised conditions for Te determination in the analysed samples were: 6 mol l -1 HCl as sample carrier solution, 0.75% (m/v) sodium tetrahydroborate as Te reductant, 40 μl of sample solution, and 200 ml min -1 Ar flow rate as carrier gas. The limit of quantification (LOQ) was 1.0 μg g -1 Te (using 250 mg of sample in 50 ml final solution), the limit of detection (LOD) was 2.5 μg l -1 and the relative standard deviation (RSD) was 6% for five consecutive measurements of sample solution. The standard addition calibration method was used. Relatively high sample throughput (ca. 45 sample runs can be performed in a working hour), reduced sample manipulation since matrix separation is not necessary, and minor waste generation are the main advantages of the proposed method for Te determination by FI-HG AAS

Attaching Copper Wires to Magnetic-Reed-Switch Leads

Science.gov (United States)

Kamila, Rudolf

1987-01-01

Bonding method reliably joins copper wires to short iron-alloy leads from glass-encased dry magnetic-reed switch without disturbing integrity of glass-to-metal seal. Joint resistant to high temperatures and has low electrical resistance.

Blood lead and lead-210 origins in residents of Toulouse

International Nuclear Information System (INIS)

Servant, J.; Delapart, M.

1981-01-01

Blood lead and lead-210 analyses were performed on blood samples from non-smoking residents of Toulouse (city of 400,000 inhabitants). Simultaneous surface soil lead content determinations were carried out by the same procedure on rural zone samples of southwestern France. The observed isotopic ratios were compared in order to evaluate food chain contamination. For an average of 19.7 +- 5.8 μg 100 cc -1 of lead in blood, atmospheric contamination amounts to 20%, estimated as follows: 6% from direct inhalation and 14% from dry deposits on vegetation absorbed as food. The natural levels carried over by the food chain reach 14.9 μg 100 cc -1 and have a 210 Pb/Pb concentration ratio of 0.055 dpmμg -1 . These results lead to a maximum value of 15 μg 100 cc -1 for natural lead in human blood according to the ICRP model. (author)

The Environmental Burdens of Lead-Acid Batteries in China: Insights from an Integrated Material Flow Analysis and Life Cycle Assessment of Lead

Directory of Open Access Journals (Sweden)

Sha Chen

2017-11-01

Full Text Available Lead-acid batteries (LABs, a widely used energy storage equipment in cars and electric vehicles, are becoming serious problems due to their high environmental impact. In this study, an integrated method, combining material flow analysis with life cycle assessment, was developed to analyze the environmental emissions and burdens of lead in LABs. The environmental burdens from other materials in LABs were not included. The results indicated that the amount of primary lead used in LABs accounted for 77% of the total lead production in 2014 in China. The amount of discharged lead into the environment was 8.54 × 105 tonnes, which was mainly from raw material extraction (57.2%. The largest environmental burden was from the raw materials extraction and processing, which accounted for 81.7% of the total environmental burdens. The environmental burdens of the environmental toxicity potential, human toxicity potential-cancer, human toxicity potential-non-cancer, water footprint and land use accounted for more than 90% at this stage. Moreover, the environmental burdens from primary lead was much more serious than regenerated lead. On the basis of the results, main practical measures and policies were proposed to reduce the lead emissions and environmental burdens of LABs in China, namely establishing an effective LABs recycling system, enlarging the market share of the legal regenerated lead, regulating the production of regenerated lead, and avoiding the long-distance transportation of the waste LABs.

Lead-Free Piezoelectrics

CERN Document Server

Nahm, Sahn

2012-01-01

Ecological restrictions in many parts of the world are demanding the elimination of Pb from all consumer items. At this moment in the piezoelectric ceramics industry, there is no issue of more importance than the transition to lead-free materials. The goal of Lead-Free Piezoelectrics is to provide a comprehensive overview of the fundamentals and developments in the field of lead-free materials and products to leading researchers in the world. The text presents chapters on demonstrated applications of the lead-free materials, which will allow readers to conceptualize the present possibilities and will be useful for both students and professionals conducting research on ferroelectrics, piezoelectrics, smart materials, lead-free materials, and a variety of applications including sensors, actuators, ultrasonic transducers and energy harvesters.

Study of core flow distribution for small modular natural circulation lead or lead-alloy cooled fast reactors

International Nuclear Information System (INIS)

Chen, Zhao; Zhao, Pengcheng; Zhou, Guangming; Chen, Hongli

2014-01-01

Highlights: • A core flow distribution calculation code for natural circulation LFRs was developed. • The comparison study between the channel method and the CFD method was conducted. • The core flow distribution analysis and optimization design for a 10MW natural circulation LFR was conducted. - Abstract: Small modular natural circulation lead or lead-alloy cooled fast reactor (LFR) is a potential candidate for LFR development. It has many attractive advantages such as reduced capital costs and inherent safety. The core flow distribution calculation is an important issue for nuclear reactor design, which will provide important input parameters to thermal-hydraulic analysis and safety analysis. The core flow distribution calculation of a natural circulation LFR is different from that of a forced circulation reactor. In a forced circulation reactor, the core flow distribution can be controlled and adjusted by the pump power and the flow distributor, while in a natural circulation reactor, the core flow distribution is automatically adjusted according to the relationship between the local power and the local resistance feature. In this paper, a non-uniform heated parallel channel flow distribution calculation code was developed and the comparison study between the channel method and the CFD method was carried out to assess the exactness of the developed code. The core flow distribution analysis and optimization design for a 10MW natural circulation LFR was conducted using the developed code. A core flow distribution optimization design scheme for a 10MW natural circulation LFR was proposed according to the optimization analysis results

Lead Toxicity

Science.gov (United States)

... o Do not use glazed ceramics, home remedies, cosmetics, or leaded-crystal glassware unless you know that they are lead safe. o If you live near an industry, mine, or waste site that may have contaminated ...

Agroindustrial Waste for Lead and Chromium Biosorption

Directory of Open Access Journals (Sweden)

Susana P. Boeykens

2018-06-01

Full Text Available There is a need to re-evaluate the residues generated in industrial processes for the production of new raw material, reducing the volume of waste. In this regard, the biosorption is a low-cost alternative method for treating effluents compared to conventional methods. The main objectives of this research were: the evaluation of the biosorbent capacity of six waste materials for the extraction of chromium(VI and lead(II ions from aqueous solutions and, the determination of the adsorption and kinetic parameters for the more efficient system. The materials evaluated were: peanut shell (Arachis hypagaea, sugarcane bagasse (Saccharum officinarum, avocado peel (Persea americana, pecan nutshell (Carya illinoinensis, wheat bran (Triticum aestivum and banana peel (Mussa paradisiaca. The highest percentage of lead removal was obtained with wheat bran (89%. For chromium, the percentage was generally much lower compared with lead for all tested biosorbents, the banana peel being the most efficient with a 10% removal. The models that better describe the adsorption processes were: Langmuir and Freundlich. The pseudo-second order kinetic model allowed obtaining the parameters for both systems. The equilibrium time, in both systems, was reached after 60 minutes. The study of Fourier Transformed Infrared spectra and the results of desorption experiments allowed to hypothesize on the mechanisms involved in the adsorption of these metals.

The lead and lead-acid battery industries during 2002 and 2007 in China

Energy Technology Data Exchange (ETDEWEB)

Chen, H.Y.; Li, A.J.; Finlow, D.E. [Key Lab of Electrochemical Technology on Energy Storage and Power Generation in Guangdong Universities, School of Chemistry and Environment, South China Normal University, Guangzhou 510006 (China)

2009-06-01

In the past 15 years, the center of the international lead market has shifted to China. China has become the largest producer of raw and refined lead, plus the largest consumer. This paper reviews the status of the lead and lead-acid battery industries in China, including lead mining, lead refining, secondary lead production, the lead-acid battery industry, new opportunities for lead-acid batteries, and the environmental problems associated with lead and lead-acid batteries. The output of raw and refined lead has increased annually in China, and now accounts for more than 30% of the world total. As a result of a change in the Chinese government's policy regarding the export of lead, plus an increase in the price of lead, the profits of Chinese lead manufacturers were significantly reduced, the trade deficit of the Chinese lead industry increased, the operating rates of lead smelter enterprises greatly reduced, and some small enterprises were forced to shut down. At the present time, an increasing number of enterprises have begun to produce secondary lead, and the scale of production has expanded from tens of tons to tens of thousands of tons. In 2006, the output of secondary lead in China reached 700,000 tons, but outdated technology and equipment limited development of the secondary lead industry. Because of serious pollution problems, raw material shortages, and fierce price competition in the battery market, changes in the development of the lead-acid battery industry have been dramatic; approximately one thousand medium-sized and small lead-acid battery producers have been closed in the past 3 years. The output of large lead-acid battery enterprises has not been reduced, however, as a result of their manufacturing technology and equipment being comparable to those in other advanced industrial countries. In China, the flourishing development of electric bicycles, electric tricycles, and photovoltaic energy systems should provide ongoing opportunities for

The lead and lead-acid battery industries during 2002 and 2007 in China

International Nuclear Information System (INIS)

Chen, H.Y.; Li, A.J.; Finlow, D.E.

2009-01-01

In the past 15 years, the center of the international lead market has shifted to China. China has become the largest producer of raw and refined lead, plus the largest consumer. This paper reviews the status of the lead and lead-acid battery industries in China, including lead mining, lead refining, secondary lead production, the lead-acid battery industry, new opportunities for lead-acid batteries, and the environmental problems associated with lead and lead-acid batteries. The output of raw and refined lead has increased annually in China, and now accounts for more than 30% of the world total. As a result of a change in the Chinese government's policy regarding the export of lead, plus an increase in the price of lead, the profits of Chinese lead manufacturers were significantly reduced, the trade deficit of the Chinese lead industry increased, the operating rates of lead smelter enterprises greatly reduced, and some small enterprises were forced to shut down. At the present time, an increasing number of enterprises have begun to produce secondary lead, and the scale of production has expanded from tens of tons to tens of thousands of tons. In 2006, the output of secondary lead in China reached 700,000 tons, but outdated technology and equipment limited development of the secondary lead industry. Because of serious pollution problems, raw material shortages, and fierce price competition in the battery market, changes in the development of the lead-acid battery industry have been dramatic; approximately one thousand medium-sized and small lead-acid battery producers have been closed in the past 3 years. The output of large lead-acid battery enterprises has not been reduced, however, as a result of their manufacturing technology and equipment being comparable to those in other advanced industrial countries. In China, the flourishing development of electric bicycles, electric tricycles, and photovoltaic energy systems should provide ongoing opportunities for the

Lead Content of Well Water in Enugu South-East Nigeria | Ogbu ...

African Journals Online (AJOL)

Aim: To study the lead content of well water in Enugu, Southeast Nigeria. Method: Wells (101) were located using the multistage sampling procedure and samples were collected into clean plastic containers. Analysis was done using atomic absorption spectrophotometer. Result: The means lead content of well water ...

A green lead hydrometallurgical process based on a hydrogen-lead oxide fuel cell.

Science.gov (United States)

Pan, Junqing; Sun, Yanzhi; Li, Wei; Knight, James; Manthiram, Arumugam

2013-01-01

The automobile industry consumed 9 million metric tons of lead in 2012 for lead-acid batteries. Recycling lead from spent lead-acid batteries is not only related to the sustainable development of the lead industry, but also to the reduction of lead pollution in the environment. The existing lead pyrometallurgical processes have two main issues, toxic lead emission into the environment and high energy consumption; the developing hydrometallurgical processes have the disadvantages of high electricity consumption, use of toxic chemicals and severe corrosion of metallic components. Here we demonstrate a new green hydrometallurgical process to recover lead based on a hydrogen-lead oxide fuel cell. High-purity lead, along with electricity, is produced with only water as the by-product. It has a >99.5% lead yield, which is higher than that of the existing pyrometallurgical processes (95-97%). This greatly reduces lead pollution to the environment.

Lead Contamination and Microbial Lead Tolerance in Soils at Major ...

African Journals Online (AJOL)

Devika

ABSTRACT: Lead pollution and lead tolerance levels of microbes in soil at major road junctions in Benin. City were investigated. Results revealed that distance from the road junctions affected the concentrations of lead in soil, as well as the microbial population density and types of microbes present in the soil. The highest ...

Lead Contamination and Microbial Lead Tolerance in Soils at Major ...

African Journals Online (AJOL)

Lead pollution and lead tolerance levels of microbes in soil at major road junctions in Benin City were investigated. Results revealed that distance from the road junctions affected the concentrations of lead in soil, as well as the microbial population density and types of microbes present in the soil. The highest concentrations ...

The effects of thiamin on lead metabolism: organ distribution of lead 203.

Science.gov (United States)

Kim, J S; Hamilton, D L; Blakley, B R; Rousseaux, C G

1992-01-01

The effect of thiamin on the organ distribution of lead was evaluated in CD-1 mice exposed intragastrically or intraperitoneally to a single dose of lead acetate (100 micrograms) containing 100 microCi lead 203. They were treated with either thiamin (25 or 50 mg/kg body weight), calcium ethylenediaminetetraacetic acid (CaEDTA) (50 mg/kg body weight), or combinations of thiamin and CaEDTA. The whole body retention and the organ distribution of lead 203 varied depending upon the route of lead administration, dose of thiamin and the specific treatment combination. Thiamin (25 or 50 mg/kg) treatment increased the whole body retention of both intragastric and intraperitoneal lead by approximately 10% in each instance. Calcium ethylenediaminetetraacetic acid, either alone or in combination with thiamin (50 mg/kg) reduced the whole body retention of lead by as much as 14% regardless of route of lead exposure. The relative retention of lead by the liver, kidney and spleen was greater in mice exposed to lead by the intragastric route. Regardless of route, CaEDTA in the combined treatment reduced the relative retention of lead in both the liver and kidney, whereas thiamin alone only reduced the retention of lead in the kidney. The results of this study indicate that thiamin in combination with CaEDTA alters the distribution and retention of lead in a manner which may have therapeutic application as it relates to chelation therapy. PMID:1423063

Lead immobilization in thermally remediated soils and igneous rocks

International Nuclear Information System (INIS)

Hickmott, D.D.; Carey, J.W.; Stimac, J.; Larocque, A.; Abell, R.; Gauerke, E.; Eppler, A.

1997-01-01

This is the final report for a three-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The principal goal of this project was to investigate the speciation of lead in the environment at LANL and to determine the feasibility of using thermal remediation methods to immobilize lead in the environment. Lead occurs as pyromorphite [Pb(PO 4 ) 3 (Cl, OH)], cerussite (PbCO 3 ) and galena (PbS) in vapor-phase-altered Bandelier Tuff samples. LANL soils primarily contain cerussite and PbO. Thermal remediation experiments at high temperatures (up to 400 C) suggest that thermal immobilization of highly-reactive Pb compounds in the environment may be feasible, but that this technique is not optimal for more refractory lead phases such as cerussite and PbO

Lead shot from hunting as a source of lead in human blood

International Nuclear Information System (INIS)

Johansen, Poul; Pedersen, Henning Sloth; Asmund, Gert; Riget, Frank

2006-01-01

This study investigates the relationship between the intake of birds hunted with lead shot and the lead concentration in human blood. Fifty adult men from Nuuk, Greenland took part in the study. From September 2003 to June 2004 they regularly gave blood samples and recorded how many birds they ate. We found a clear relationship between the number of bird meals and blood lead and also a clear seasonal variation. The concentration was highest in mid-winter when bird consumption is at its highest. Blood lead was low (15 μg/L, mean concentration) among the participants reporting not eating birds. Among those reporting to eat birds regularly, blood lead was significantly higher, up to 128 μg/L (mean concentration). Concentrations depended on the frequency of bird meals: the more the bird meals, the higher the resulting blood lead. This clear relationship points to lead shot as the dominating lead source to people in Greenland. - Birds hunted with lead shot and consumed are a source of lead in human blood

Lead shot from hunting as a source of lead in human blood

Energy Technology Data Exchange (ETDEWEB)

Johansen, Poul [National Environmental Research Institute, Frederiksborgvej 399, DK-4000 Roskilde (Denmark)]. E-mail: poj@dmu.dk; Pedersen, Henning Sloth [Primary Health Care Center, DK-3900 Nuuk (Greenland); Asmund, Gert [National Environmental Research Institute, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Riget, Frank [National Environmental Research Institute, Frederiksborgvej 399, DK-4000 Roskilde (Denmark)

2006-07-15

This study investigates the relationship between the intake of birds hunted with lead shot and the lead concentration in human blood. Fifty adult men from Nuuk, Greenland took part in the study. From September 2003 to June 2004 they regularly gave blood samples and recorded how many birds they ate. We found a clear relationship between the number of bird meals and blood lead and also a clear seasonal variation. The concentration was highest in mid-winter when bird consumption is at its highest. Blood lead was low (15 {mu}g/L, mean concentration) among the participants reporting not eating birds. Among those reporting to eat birds regularly, blood lead was significantly higher, up to 128 {mu}g/L (mean concentration). Concentrations depended on the frequency of bird meals: the more the bird meals, the higher the resulting blood lead. This clear relationship points to lead shot as the dominating lead source to people in Greenland. - Birds hunted with lead shot and consumed are a source of lead in human blood.

Optical Studies on Sol-Gel Derived Lead Chloride Crystals

OpenAIRE

Rejeena, I; Lillibai, B; Nithyaja, B; Nampoori, P.N V; Radhakrishnan, P

2013-01-01

Optical characterization of lead chloride crystals prepared by sol-gel method is reported. The relevant sol-gel technique is used for the preparation of PbCl2 samples with five different types. In this paper, we report the absorption and fluorescence behaviour of pure, UV& IR irradiated and electric & magnetic field applied lead chloride crystal samples in solution phase at two different concentrations. Optical bandgap and emission studies of these crystals are also done.

Antiviral lead compounds from marine sponges

KAUST Repository

Sagar, Sunil

2010-10-11

Marine sponges are currently one of the richest sources of pharmacologically active compounds found in the marine environment. These bioactive molecules are often secondary metabolites, whose main function is to enable and/or modulate cellular communication and defense. They are usually produced by functional enzyme clusters in sponges and/or their associated symbiotic microorganisms. Natural product lead compounds from sponges have often been found to be promising pharmaceutical agents. Several of them have successfully been approved as antiviral agents for clinical use or have been advanced to the late stages of clinical trials. Most of these drugs are used for the treatment of human immunodeficiency virus (HIV) and herpes simplex virus (HSV). The most important antiviral lead of marine origin reported thus far is nucleoside Ara-A (vidarabine) isolated from sponge Tethya crypta. It inhibits viral DNA polymerase and DNA synthesis of herpes, vaccinica and varicella zoster viruses. However due to the discovery of new types of viruses and emergence of drug resistant strains, it is necessary to develop new antiviral lead compounds continuously. Several sponge derived antiviral lead compounds which are hopedto be developed as future drugs are discussed in this review. Supply problems are usually the major bottleneck to the development of these compounds as drugs during clinical trials. However advances in the field of metagenomics and high throughput microbial cultivation has raised the possibility that these techniques could lead to the cost-effective large scale production of such compounds. Perspectives on biotechnological methods with respect to marine drug development are also discussed. 2010 by the authors; licensee MDPI.

The leaching of lead from lead-based paint in landfill environments.

Science.gov (United States)

Wadanambi, Lakmini; Dubey, Brajesh; Townsend, Timothy

2008-08-30

Lead leaching from lead-based paint (LBP) was examined using standardized laboratory protocols and tests with leachate from actual and simulated landfill environments. Two different LBP samples were tested; leaching solutions included leachates from three municipal solid waste (MSW) landfills and three construction and demolition (C&D) debris landfills. The toxicity characteristic leaching procedure (TCLP) and the synthetic precipitation leaching procedure (SPLP) were also performed. Lead concentrations were many times higher using the TCLP compared to the SPLP and the landfill leachates. No significant difference (alpha=0.05) was observed in leached lead concentrations from the MSW landfill and C&D debris landfill leachates. The impact of other building materials present in LBP debris on lead leaching was examined by testing mixtures of LBP (2%) and different building materials (98%; steel, wood, drywall, concrete). The type of substrate present impacted lead leaching results, with concrete demonstrating the most dramatic impact; the lowest lead concentrations were measured in the presence of concrete under both TCLP and SPLP extractions.

Factors affecting the absorption and excretion of lead in the rat

International Nuclear Information System (INIS)

Conrad, M.E.; Barton, J.C.

1978-01-01

A reliable method for studying lead absorption and excretion in rats is described. Lead absorption occurs primarily in the duodenum where lead enters the epithelial mucosal cells. There is a relative mucosal block for lead with increasing intraluminal doses. Certain substances which bind lead and increase its solubility enhance its absorption. Iron, zinc, and calcium decrease the absorption of lead without affecting its solubility, probably by competing for shared absorptive receptors in the intestinal mucosa. The total body burden of lead does not affect lead absorption. Thus, lead does not have a feedback mechanism which limits absorption. Lead absorption is increased during rapid periods of growth and in iron-deficient animals. It is diminished with starvation and in iron-overloaded animals. The excretion and kinetics of tracer doses of radiolead were quantified. Erythrocytes seem to serve an important role in transport. Excretion occurs in urine and stool. Bile is an important route of excretion in the gut. Although most of a tracer dose is rapidly excreted, the excretory process is limited permitting lead accumulation primarily in bone

Relationship between soil lead and airborne lead concentrations at Springfield, Missouri, USA

Energy Technology Data Exchange (ETDEWEB)

Sheets, R W; Kyger, J R; Biagioni, R N; Probst, S [Department of Chemistry, Southwest Missouri State University, 65804 Springfield, MO (United States); Boyer, R; Barke, K [Greene County Health Department, 65802 Springfield, MO (United States)

2001-04-23

This study tests whether lead deposited to soil from automobiles during past years in a medium-sized US city (population 150000) may present a current health risk. It examines the relationship between current soil lead concentrations at nine locations within the city of Springfield, Missouri, and airborne lead levels measured at the same locations during years (1975-1981) when lead emissions from automobiles were much greater than at present. A strong, significant correlation is found between soil and airborne lead levels at eight of the sites (r=0.91, P<0.005 for soil lead vs. 1979 airborne lead), in low-traffic areas as well as in areas adjacent to heavy traffic flow. Residual lead concentrations in these soils are relatively low, even for the high-traffic sites, as expected for a medium sized city.

Corrosion by liquid lead and lead-bismuth: experimental results review and analysis

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jinsuo [Los Alamos National Laboratory

2008-01-01

Liquid metal technologies for liquid lead and lead-bismuth alloy are under wide investigation and development for advanced nuclear energy systems and waste transmutation systems. Material corrosion is one of the main issues studied a lot recently in the development of the liquid metal technology. This study reviews corrosion by liquid lead and lead bismuth, including the corrosion mechanisms, corrosion inhibitor and the formation of the protective oxide layer. The available experimental data are analyzed by using a corrosion model in which the oxidation and scale removal are coupled. Based on the model, long-term behaviors of steels in liquid lead and lead-bismuth are predictable. This report provides information for the selection of structural materials for typical nuclear reactor coolant systems when selecting liquid lead or lead bismuth as heat transfer media.

Relationship between soil lead and airborne lead concentrations at Springfield, Missouri, USA.

Science.gov (United States)

Sheets, R W; Kyger, J R; Biagioni, R N; Probst, S; Boyer, R; Barke, K

2001-04-23

This study tests whether lead deposited to soil from automobiles during past years in a medium-sized US city (population 150,000) may present a current health risk. It examines the relationship between current soil lead concentrations at nine locations within the city of Springfield, Missouri, and airborne lead levels measured at the same locations during years (1975-1981) when lead emissions from automobiles were much greater than at present. A strong, significant correlation is found between soil and airborne lead levels at eight of the sites (r = 0.91, P lead vs. 1979 airborne lead), in low-traffic areas as well as in areas adjacent to heavy traffic flow. Residual lead concentrations in these soils are relatively low, even for the high-traffic sites, as expected for a medium sized city.

Liquid Membrane System for Extraction and Electrodeposition of Lead(II During Electrodialysis

Directory of Open Access Journals (Sweden)

Sadyrbaeva Tatiana

2017-05-01

Full Text Available A novel method for lead(II removal from aqueous acidic solutions is presented. The method involves electrodialysis through bulk liquid membranes accompanied by electrodeposition of metal from the cathodic solution. Solutions of di(2-ethylhexylphosphoric acid with admixtures of tri-n-octylamine in 1,2-dichloroethane were used as the liquid membranes. The effects of the main electrodialysis parameters as well as of the composition of the liquid membranes and aqueous solutions on the lead(II transport rate are studied. The optimal conditions are determined. A possibility of effective single-stage transfer of lead(II through the liquid membrane into dilute solutions of perchloric, nitric and acetic acids is demonstrated. Dense and adherent lead electrodeposits are obtained from perchloric acid solutions. Maximum extraction degree of 93 % and electrodeposition degree of ~60 % are obtained during 5 h of electrodialysis.

Characteristics of polonium contamination from neutral irradiated lead-bismuth eutectic

International Nuclear Information System (INIS)

Miura, T.; Obara, T.; Sekimoto, H.

2004-01-01

After neutron capture, bismuth-209 changes to polonium-210 that emits α-particles. Lead-Bismuth eutectic (LBE) in reactor system contaminates the system by polonium. We analyzed adsorbed materials from melted LBE on quartz glass plate. Lead, bismuth and their oxides were confirmed in adsorbed materials. And, we evaluated the baking method in vacuum for removal of polonium and adsorbed materials on quartz glass plate. It was evaluated that it is possible to remove almost all the polonium from the quartz glass plate by baking at temperature more than 300 C. degrees. Unfolding method was applied to calculate polonium distribution in LBE ingot. From measured α-particle pulse height distribution, the polonium distribution in depth of LBE ingot was calculated using quadratic programming code, where response functions are calculated by Monte Carlo method. (authors)

Discuss the cause and treatment of pacemaker lead dislocation and deal with

International Nuclear Information System (INIS)

Chen Yueguang; Zhang Dadong; Lu Jie; Yang Hui; Liu Chunyan; Zhang Wei

2003-01-01

Objective: To follow up the patients with pacemaker, observe the condition of pacemaker lead, to explore the cause of lead dislocation, to find out and prevent its occurrence. Methods: Summarizing the clinical data of 6 patients with pacemaker, 7 pacemaker leads with 8 time dislocation, pacemaker 2 DDDR, 2 DDD, 2 VVI. Results: Four patients were punctured from right subclavian vein, one from left subclavian vein and one from right brachiocephalic vein; four leads were dislocation in atrium and one mildly dislocation; four leads dislocation in ventricle and two mildly dislocation; There were 3 old women with 4 leads and 5 times of dislocation

HTS power lead testing at the Fermilab magnet test facility

Energy Technology Data Exchange (ETDEWEB)

Rabehl, R.; Carcagno, R.; Feher, S.; Huang, Y.; Orris, D.; Pischalnikov, Y.; Sylvester, C.; Tartaglia, M.; /Fermilab

2005-08-01

The Fermilab Magnet Test Facility has tested high-temperature superconductor (HTS) power leads for cryogenic feed boxes to be placed at the Large Hadron Collider (LHC) interaction regions and at the new BTeV C0 interaction region of the Fermilab Tevatron. A new test facility was designed and operated, successfully testing 20 pairs of HTS power leads for the LHC and 2 pairs of HTS power leads for the BTeV experiment. This paper describes the design and operation of the cryogenics, process controls, data acquisition, and quench management systems. Results from the facility commissioning are included, as is the performance of a new insulation method to prevent frost accumulation on the warm ends of the power leads.

HTS power lead testing at the Fermilab magnet test facility

International Nuclear Information System (INIS)

Rabehl, R.; Carcagno, R.; Feher, S.; Huang, Y.; Orris, D.; Pischalnikov, Y.; Sylvester, C.; Tartaglia, M.

2005-01-01

The Fermilab Magnet Test Facility has tested high-temperature superconductor (HTS) power leads for cryogenic feed boxes to be placed at the Large Hadron Collider (LHC) interaction regions and at the new BTeV CO interaction region of the Fermilab Tevatron. A new test facility was designed and operated, successfully testing 20 pairs of HTS power leads for the LHC and 2 pairs of HTS power leads for the BTeV experiment. This paper describes the design and operation of the cryogenics, process controls, data acquisition, and quench management systems. Results from the facility commissioning are included, as is the performance of a new insulation method to prevent frost accumulation on the warm ends of the power leads

Library design practices for success in lead generation with small molecule libraries.

Science.gov (United States)

Goodnow, R A; Guba, W; Haap, W

2003-11-01

The generation of novel structures amenable to rapid and efficient lead optimization comprises an emerging strategy for success in modern drug discovery. Small molecule libraries of sufficient size and diversity to increase the chances of discovery of novel structures make the high throughput synthesis approach the method of choice for lead generation. Despite an industry trend for smaller, more focused libraries, the need to generate novel lead structures makes larger libraries a necessary strategy. For libraries of a several thousand or more members, solid phase synthesis approaches are the most suitable. While the technology and chemistry necessary for small molecule library synthesis continue to advance, success in lead generation requires rigorous consideration in the library design process to ensure the synthesis of molecules possessing the proper characteristics for subsequent lead optimization. Without proper selection of library templates and building blocks, solid phase synthesis methods often generate molecules which are too heavy, too lipophilic and too complex to be useful for lead optimization. The appropriate filtering of virtual library designs with multiple computational tools allows the generation of information-rich libraries within a drug-like molecular property space. An understanding of the hit-to-lead process provides a practical guide to molecular design characteristics. Examples of leads generated from library approaches also provide a benchmarking of successes as well as aspects for continued development of library design practices.

Urban gardens: Lead exposure, recontamination mechanisms, and implications for remediation design

International Nuclear Information System (INIS)

Clark, Heather F.; Hausladen, Debra M.; Brabander, Daniel J.

2008-01-01

Environmental lead contamination is prevalent in urban areas where soil represents a significant sink and pathway of exposure. This study characterizes the speciation of lead that is relevant to local recontamination and to human exposure in the backyard gardens of Roxbury and Dorchester, MA, USA. One hundred forty-one backyard gardens were tested by X-ray fluorescence, and 81% of gardens have lead levels above the US EPA action limit of 400 μg/g. Raised gardening beds are the in situ exposure reduction method used in the communities to promote urban gardening. Raised beds were tested for lead and the results showed that the lead concentration increased from an initial range of 150±40 μg/g to an average of 336 μg/g over 4 years. The percent distribution of lead in the fine grain soil (<100 μm) and the trace metal signature of the raised beds support the conclusion that the mechanism of recontamination is wind-transported particles. Scanning electron microscopy and sequential extraction were used to characterize the speciation of lead, and the trace metal signature of the fine grain soil in both gardens and raised gardening beds is characteristic of lead-based paint. This study demonstrates that raised beds are a limited exposure reduction method and require maintenance to achieve exposure reduction goals. An exposure model was developed based on a suite of parameters that combine relevant values from the literature with site-specific quantification of exposure pathways. This model suggests that consumption of homegrown produce accounts for only 3% of children's daily exposure of lead while ingestion of fine grained soil (<100 μm) accounts for 82% of the daily exposure. This study indicates that urban lead remediation on a yard-by-yard scale requires constant maintenance and that remediation may need to occur on a neighborhood-wide scale

Virtual reality lead extraction as a method for training new physicians: a pilot study.

Science.gov (United States)

Maytin, Melanie; Daily, Thomas P; Carillo, Roger G

2015-03-01

It is estimated that the demand for transvenous lead extraction (TLE) has reached an annual extraction rate of nearly 24,000 patients worldwide. Despite technologic advances, TLE still has the potential for significant morbidity and mortality. Complication rates with TLE directly parallel operator experience. However, obtaining adequate training during and postfellowship can be difficult. Given the potential for catastrophic complications and the steep learning curve (up to 300 cases) associated with this procedure, we sought to validate a virtual reality (VR) lead extraction simulator as an innovative training and evaluation tool for physicians new to TLE. We randomized eight electrophysiology fellows to VR simulator versus conventional training. We compared procedural skill competency between the groups using simulator competency, tactile measurements, markers of proficiency and attitudes, and cognitive abilities battery. Practical skills and simulator complications differed significantly between the VR simulator and conventional training groups. The VR simulator group executed patient preparation and procedure performance better than the conventional group (P training experienced a simulator complication (two superior vena cava [SVC] tears, three right ventricle [RV] avulsions) versus one fellow in the VR simulator group (one SVC tear) (P = 0.02). Tactile measurements revealed a trend toward excess pushing versus pulling forces among the conventionally trained group. The time for lead removal was also significantly higher in the conventional training group (12.46 minutes vs 5.54 minutes, P = 0.02). There was no significant difference in baseline or posttraining cognitive ability. We contend that the implementation of alternative training tools such as a VR simulation model will improve physician training and allow for an innovative pathway to assess the achievement of competency. ©2014 Wiley Periodicals, Inc.

Applications of lead isotope rations for identification and apportionment on pollution sources in food

International Nuclear Information System (INIS)

Zhao Duoyong; Wei Yimin; Guo Boli; Wei Shuai

2011-01-01

Lead is one of the toxic heavy metals which can accumulate to an adverse effect level in human bodies through ingestion, inhalation or other pathways. Because of the persistent lead contamination in farmland environment, large risk exists in the primary stage of 'from farm to table' chain. Environmental media such as soils, atmospheric aerosols were the possible lead sources of agro-food. To pinpoint the pollution sources exactly, cut off the contamination pathways in time, and reduce the risk of hazard, pollution sources tracing was very important. Lead isotope ratio combined with certain models is an effective method to discriminate correctly pollution sources and calculate the individual source contributions. In this review, to provide theoretical and technical reference for controlling lead pollution in environment and food, lead pollution sources in food, tracing principle and methods of lead isotope ratios, and its applications on vegetable, tea, wine, cereal and other food products were concerned. (authors)

Lead dust in Broken Hill homes: effect of remediation on indoor lead levels.

Science.gov (United States)

Boreland, F; Lyle, D M

2006-02-01

This study was undertaken to determine whether home remediation effectively reduced indoor lead levels in Broken Hill, a long-established silver-lead-zinc mining town in outback Australia. A before-after study of the effect of home remediation on indoor lead levels was embedded into a randomized controlled trial of the effectiveness of remediation for reducing elevated blood lead levels in young children. Moist towelettes were used to measure lead loading (microg/m2) on internal windowsills and internal and entry floors of 98 homes; samples were collected before, immediately after, and 2, 4, 6, 8, and 10 months after remediation. Data were log(10) transformed for the analysis. Remediation reduced average indoor lead levels by approximately 50%, and lead levels remained low for the duration of the follow-up period (10 months). The greatest gains were made in homes with the highest initial lead levels; homes with low preremediation lead levels showed little or no benefit. Before remediation, homes located in areas with high soil lead levels or with "poor" dust proofing had higher lead levels than those in areas with lower soil lead levels or with "medium" or "good" dust proofing; these relative differences remained after remediation. There was no evidence that lead loading was reduced by an increased opportunity to become aware of lead issues. We conclude that remediation is an effective strategy for reducing the lead exposure of children living in homes with high indoor lead levels.

Lead iodide X-ray and gamma-ray spectrometers for room and high temperature operation

International Nuclear Information System (INIS)

Hermon, H.; James, R.B.; Lund, J.

1998-01-01

In this study the authors report on the results of the investigation of lead iodide material properties. The effectiveness of a zone refining purification method on the material purity is determined by ICP-MS and ICP-OES and correlated to the electrical and physical material properties. They show that this zone refining method is very efficient in removing impurities from lead iodide, and they also determine the segregation coefficient for some of these impurities. Triple axis X-ray diffraction (TAD) analysis has been used to determine the crystalline perfection of the lead iodide after applying various cutting, etching and fabrication methods. The soft lead iodide crystal was found to be damaged when cleaved by a razor blade, but by using a diamond wheel saw, followed by etching, the crystallinity of the material was much improved, as observed by TAD. Low temperature photoluminescence also indicates an improvement in the material properties of the purified lead iodide. Electrical properties of lead iodide such as carrier mobility, were calculated based on carrier-phonon scattering. The results for the electrical properties were in good agreement with the experimental data

Using the methods of radiospectroscopy (EPR, NMR) to study the nature of the defect structure of solid solutions based on lead zirconate titanate (PZT).

Science.gov (United States)

Bykov, Igor; Zagorodniy, Yuriy; Yurchenko, Lesya; Korduban, Alexander; Nejezchleb, Karel; Trachevsky, Vladimir; Dimza, Vilnis; Jastrabik, Lubomir; Dejneka, Alexander

2014-08-01

The nature of intrinsic and impurity point defects in lead zirconate titanate (PZT) ceramics has been explored. Using electron paramagnetic resonance (EPR), nuclear magnetic resonance (NMR), and X-ray photoelectron spectroscopy (XPS) methods, several impurity sites have been identified in the materials, including the Fe(3+)-oxygen vacancy (VO) complex and Pb ions. Both of these centers are incorporated into the PZT lattice. The Fe(3+) –VО paramagnetic complex serves as a sensitive probe of the local crystal field in the ceramic; the symmetry of this defect roughly correlates with PZT phase diagram as the composition is varied from PbTiO3 to PbZrO3. NMR spectra (207)Pb in PbTiO3, PbZrO3, and PZT with iron content from 0 to 0.4 wt% showed that increasing the iron concentration leads to a distortion of the crystal structure and to improvement of the electrophysical parameters of the piezoceramics. This is due to the formation of a phase which has a higher symmetry, but at high concentrations of iron (>0.4 wt%), it leads to sharp degradation of electrophysical parameters.

High human exposure to lead through consumption of birds hunted with lead shot

International Nuclear Information System (INIS)

Johansen, P.; Asmund, G.; Riget, F.

2004-01-01

Lead shot contaminates the edible parts of birds so that tolerable human lead intake is exceeded. - We assess lead contamination of Greenland seabirds killed with lead shot having studied thick-billed murre and common eider, the two most important species in the diet. The lead concentration is very high in meat of eiders killed with lead shot (mean 6.1 μg/g-wet wt, 95% CL 2.1-12). This level is about 44 times higher than in drowned eiders and eight times higher than in shot murres. Analyzing whole breasts instead of sub-samples reveals about seven times higher lead levels in birds' meat. We conclude that in some cases the lead intake by Greenland bird eaters will largely exceed the FAO/WHO tolerable lead intake guideline and that lead shot is a more important source of lead in the diet than previously estimated

Lead in the environment

Science.gov (United States)

Pattee, Oliver H.; Pain, Deborah J.; Hoffman, David J.; Rattner, Barnett A.; Burton, G. Allen; Cairns, John

2003-01-01

Anthropogenic uses of lead have probably altered its availability and environmental distribution more than any other toxic element. Consequently, lead concentrations in many living organisms may be approaching thresholds of toxicity for the adverse effects of lead. Such thresholds are difficult to define, as they vary with the chemical and physical form of lead, exposure regime, other elements present and also vary both within and between species. The technological capability to accurately quantify low lead concentrations has increased over the last decade, and physiological and behavioral effects have been measured in wildlife with tissue lead concentrations below those previously considered safe for humans.s.236 Consequently. lead criteria for the protection of wildlife and human health are frequently under review, and 'thresholds' of lead toxicity are being reconsidered. Proposed lead criteria for the protection of natural resources have been reviewed by Eisler. Uptake of lead by plants is limited by its generally low availability in soils and sediments, and toxicity may be limited by storage mechanisms and its apparently limited translocation within most plants. Lead does not generally accumulate within the foliar parts of plants, which limits its transfer to higher trophic levels. Although lead may concentrate in plant and animal tissues, no evidence of biomagnification exists. Acid deposition onto surface waters and soils with low buffering capacity may influence the availability of lead for uptake by plants and animals, and this may merit investigation at susceptible sites. The biological significance of chronic low-level lead exposure to wildlife is sometimes difficult to quantify. Animals living in urban environments or near point sources of lead emission are inevitably subject to greater exposure to lead and enhanced risk of lead poisoning. Increasingly strict controls on lead emissions in many countries have reduced exposure to lead from some sources

Aminolevulinate dehydrogenase polymorphisms did not modified lead serum and memory relationship

Directory of Open Access Journals (Sweden)

Lantip Rujito

2015-12-01

Full Text Available BACKGROUND Lead accumulation in the blood widely known affecting the formation of heme and oxygen transport processes in vital organs, Leading to organ failure including the brain synapses. Lead affinity has been recognized influenced by constitutional genotype of aminolevulinate dehydrogenase (ALAD, which encodes for heme synthesis. This research aimed to determine the relationship between plumbum (Pb and short term memory on each ALAD gene genotyping (ALAD 1-1, ALAD 1-2 or ALAD 2-2 in gas station workers. METHODS Seventy six probands from gas station workers were recruited to participate in this research. Each probands was carried out ALAD genotyping using polymerase chain reaction-restriction fragment length polymorphism (PCRRFLP method, lead serum level using atomic absorbent spectrophotometer (AAS, and short term memory was measurement by intelligence structure test (IST. RESULTS Proportion of δ ALAD 1-1, 1-2, and 2-2 were 91.8%, 8.2% and 0% respectively. Lead serum showed 15.84 ppb in homozygous 1-1, and 20.79 ppb in heterozygous. Short term memory in the probands varied from 85 until 117, with average in 99.71. There was significant negative relationship between lead serum and short term memory (r=-0.24; p=0.038. However, we could not find any significant correlation in each δ ALAD genotypes. CONCLUSION The δ ALAD genotypes did not modified the relationship between serum lead level and short term memory in gas station workers.

Ultrafast time-resolved spectroscopy of lead halide perovskite films

Science.gov (United States)

Idowu, Mopelola A.; Yau, Sung H.; Varnavski, Oleg; Goodson, Theodore

2015-09-01

Recently, lead halide perovskites which are organic-inorganic hybrid structures, have been discovered to be highly efficient as light absorbers. Herein, we show the investigation of the excited state dynamics and emission properties of non-stoichiometric precursor formed lead halide perovskites grown by interdiffusion method using steady-state and time-resolved spectroscopic measurements. The influence of the different ratios of the non-stoichiometric precursor solution was examined. The observed photoluminescence properties were correlated with the femtosecond transient absorption measurements.

Lead exposure from lead pellets: age-related accumulation in mute swans

Energy Technology Data Exchange (ETDEWEB)

Eskildsen, J.; Grandjean, P.

1984-05-01

In a cross-sectional study of adult swans and their successfully fledged young in Ringkobing Fjord, West Jutland, Denmark, 128 venous blood samples were taken during the moulting period and analyzed for lead. While the juveniles generally showed blood lead levels below 15 micrograms/100 ml (median, 11 micrograms/100 ml), the values were significantly higher in adults (median, 25 micrograms/100 ml). Adult females showed slightly higher levels than did adult males. None of the birds examined showed signs of acute lead toxicity, and increased blood levels in adults may reflect increased lead body burdens from previous ingestion of lead shot as gizzard stones.

Lead-free piezoceramics.

Science.gov (United States)

Saito, Yasuyoshi; Takao, Hisaaki; Tani, Toshihiko; Nonoyama, Tatsuhiko; Takatori, Kazumasa; Homma, Takahiko; Nagaya, Toshiatsu; Nakamura, Masaya

2004-11-04

Lead has recently been expelled from many commercial applications and materials (for example, from solder, glass and pottery glaze) owing to concerns regarding its toxicity. Lead zirconium titanate (PZT) ceramics are high-performance piezoelectric materials, which are widely used in sensors, actuators and other electronic devices; they contain more than 60 weight per cent lead. Although there has been a concerted effort to develop lead-free piezoelectric ceramics, no effective alternative to PZT has yet been found. Here we report a lead-free piezoelectric ceramic with an electric-field-induced strain comparable to typical actuator-grade PZT. We achieved this through the combination of the discovery of a morphotropic phase boundary in an alkaline niobate-based perovskite solid solution, and the development of a processing route leading to highly textured polycrystals. The ceramic exhibits a piezoelectric constant d33 (the induced charge per unit force applied in the same direction) of above 300 picocoulombs per newton (pC N(-1)), and texturing the material leads to a peak d33 of 416 pC N(-1). The textured material also exhibits temperature-independent field-induced strain characteristics.

A rapid method for simultaneous determination of arsenic, cadmium and lead in drinking water by inductively coupled plasma mass spectrometry

Directory of Open Access Journals (Sweden)

Joshua Rey P. Torres

Full Text Available The raw water source of drinking water in most areas in the Philippines is typically river water and in some cases groundwater. These sources are prone to elevated levels of metals and metalloids that may cause exposure of the general population when the treatment of the water is inadequate. This work presents a simple method based on EPA Method 200.8 for the determination of total concentrations of arsenic (As, cadmium (Cd and lead (Pb in drinking water using inductively coupled plasma-mass spectrometry (ICP-MS as the element-selective detector. This was applied in the determination of these elements in the water supply in Metro Manila, Philippines. The method detection limits were 0.095 μg L-1, 0.043 μg L-1, and 0.114 μg L-1 for total As, Cd and Pb, respectively.The method was validated using National Institute of Standards and Technology (NIST 1643e certified reference material for trace elements in water and determined values were 60.4 ± 0.5 μg L-1, 6.7 ± 0.1 μg L-1, and 19.6 ± 0.5 μg L-1 for As, Cd and Pb, respectively. These determined values were in good agreement with the certified values in the reference material. Analysis of actual drinking water samples showed that most samples did not exceed the limit of the Philippine drinking water standard for the elements.

Mass spectrometric study of thermodynamic properties of gaseous lead tellurates. Estimation of formation enthalpies of gaseous lead polonates

Energy Technology Data Exchange (ETDEWEB)

Shugurov, S.M., E-mail: s.shugurov@spbu.ru; Panin, A.I.; Lopatin, S.I.; Emelyanova, K.A.

2016-10-15

Gaseous reactions involving lead oxides, tellurium oxide and lead tellurates were studied by the Knudsen effusion mass spectrometry. Equilibrium constants and reaction enthalpies were evaluated. Structures, molecular parameters and thermodynamic functions of gaseous PbTeO{sub 3} and Pb{sub 2}TeO{sub 4} were calculated by quantum chemistry methods. The formation enthalpies Δ{sub f}H{sup 0} (298.15) = −294 ± 13 for gaseous PbTeO{sub 3} and Δ{sub f}H{sup 0} (298.15) = −499 ± 12 for gaseous Pb{sub 2}TeO{sub 4} were obtained. On the base of these results the formation enthalpies of gaseous PbPoO{sub 3} and Pb{sub 2}PoO{sub 4} were estimated as −249 ± 34 and −478 ± 38, respectively. - Highlights: • Gaseous lead tellurates PbTeO{sub 3}, Pb{sub 2}TeO{sub 4} were discovered. • Their thermodynamic properties were studied using both high temperature mass spectrometry and quantum chemistry computations. • The obtained data allows to predict the formation enthalpies of gaseous lead polonates PbPoO{sub 3}, Pb{sub 2}PoO{sub 4}.

Active gas discharge cleaning for superconducting lead-plated resonators

International Nuclear Information System (INIS)

Malev, M.D.; Weisser, D.C.

1985-06-01

Lead-plating for superconducting RF resonators historically has been directed toward reducing grain size and eliminating spikes on the surface. Investigations were made of degassing lead-plated surfaces under RF resonant electron discharge or multipacting. The mass-spectra of the residual atmosphere showed that decomposition of hydrocarbons on the surface took place. Discolouration of the lead surface, due to the formation of a carbon layer, was easily observed. A method of cleaning surfaces by ion bombardment employing chemically active gases, was proposed and tested. An RF discharge, initiated by multipacting at pressure 10 -2 - 10 -1 torr was used. The first step, discharge treatment in a CO 2 atmosphere, assures oxidation of carbon and hydrocarbons into gaseous compounds which are removed by pumping. During the second step, discharge treatment in a hydrogen atmosphere, lead oxides are reduced to metal

Derivative spectrophotometric determination of trace lead in alloys ...

African Journals Online (AJOL)

diethylaminophenol-ammonium tetraphenylborate with microcrystalline naphthalene or by a column method in the pH range 4.0–6.0 from a large volume of aqueous solutions of various samples. After filtration, the solid mass consisting of the lead complex and ...

The relationship between blood lead levels and occupational exposure in a pregnant population

OpenAIRE

Osmel La-Llave-León; José Manuel Salas Pacheco; Sergio Estrada Martínez; Eloísa Esquivel Rodríguez; Francisco X. Castellanos Juárez; Ada Sandoval Carrillo; Angélica María Lechuga Quiñones; Fernando Vázquez Alanís; Gonzalo García Vargas; Edna Madai Méndez Hernández; Jaime Duarte Sustaita

2016-01-01

Background Pregnant women exposed to lead are at risk of suffering reproductive damages, such as miscarriage, preeclampsia, premature delivery and low birth weight. Despite that the workplace offers the greatest potential for lead exposure, there is relatively little information about occupational exposure to lead during pregnancy. This study aims to assess the association between blood lead levels and occupational exposure in pregnant women from Durango, Mexico. Methods A cross-sectional stu...

Efficiency of lead removal from drinking water using cationic resin Purolite

Directory of Open Access Journals (Sweden)

Ashour Mohammad Merganpour

2015-01-01

Full Text Available Background: Today, issues such as water shortage, difficulties and costs related to supplying safe water, and anomalous concentrations of heavy metals in groundwater and surface water resources, doubled the necessity of access to technical methods on removing these pollutants from water resources. Methods: In this lab study, cationic resin Purolite S-930 (with co-polymer styrene di-vinyl benzene structure was used for lead removal from drinking water containing up to 22 μg/L. Using statistical analysis and designing a full factorial experiment are the most important effective parameters on lead removal obtained through ion exchange process. Results: Analysis of response and interaction parameters of ion exchange showed that the resin column height has maximum and pH value has minimum effect on the efficiency of lead removal from aquatic environment. Trinary interaction of “effective size, flow rate, resin column high” has the most important for lead removal efficiency in this system. So the maximum efficiency was obtained at the mesh = 40, bed height =1.6 meter, and pH= 6.5. At the best operation conditions, ability to remove 95.42% of lead concentration can be achieved. Conclusion: Using the resin Purolite S-930 during 21-day service with 91.12% of mean lead removal ratio from drinking water is an economic and technical feasibility.

Leading-edge vortex shedding from rotating wings

Energy Technology Data Exchange (ETDEWEB)

Kolomenskiy, Dmitry [Centre de Recherches Mathématiques (CRM), Department of Mathematics and Statistics, McGill University, 805 Sherbrooke W., Montreal, QC H3A 0B9 (Canada); Elimelech, Yossef [Faculty of Aerospace Engineering, Technion-Israel Institute of Technology, Haifa 32000 (Israel); Schneider, Kai, E-mail: dkolom@gmail.com [M2P2–CNRS, Université d' Aix-Marseille, 39, rue Frédéric Joliot-Curie, F-13453 Marseille Cedex 13 (France)

2014-06-01

This paper presents a numerical investigation of the leading-edge vortices generated by rotating triangular wings at Reynolds number Re = 250. A series of three-dimensional numerical simulations have been carried out using a Fourier pseudo-spectral method with volume penalization. The transition from stable attachment of the leading-edge vortex to periodic vortex shedding is explored, as a function of the wing aspect ratio and the angle of attack. It is found that, in a stable configuration, the spanwise flow in the recirculation bubble past the wing is due to the centrifugal force, incompressibility and viscous stresses. For the flow outside of the bubble, an inviscid model of spanwise flow is presented. (papers)

Photocatalyzed removal of lead ion from lead-chelator solution

Energy Technology Data Exchange (ETDEWEB)

Cho, Young Hyun; Na, Jung Won; Sung, Ki Woung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1994-07-01

The present study was undertaken to examine the influence of such chelating agents on the ease and speed of photocatalyzed metal removal and deposition. With excess EDTA, the free EDTA competes with Pb for oxidation, and at a ten fold excess, no lead oxidation (hence removal) occurs. With insufficient EDTA, the corresponding initial concentration of Pb-EDTA is decreased; after its destruction, the remaining Pb{sup 2+} is removed more slowly, at rates found with lead nitrate solution. The net result is that the maximum rate of lead deposition occurs at the stoichiometric ratio of 1:1 EDTA : Pb{sup 2+}.

Vector boson and Charmonium production in proton-lead and lead-lead collisions with ATLAS at the LHC

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00241320; The ATLAS collaboration

2016-01-01

Electroweak bosons do not interact strongly with the dense and hot medium formed in nuclear collisions, and thus should be sensitive to the nuclear modification of parton distribution functions (nPDFs). The in-medium modification of heavy charmonium states plays an important role in studying the hot and dense medium. The ATLAS detector, optimized to search for new physics in proton-proton collisions, is well equipped to measure Z and W bosons as well as quarkonium in the high occupancy environment produced in heavy ion collisions. Results from the ATLAS experiment on W and Z boson yields as a function of centrality, transverse momentum and rapidity, in lead-lead and proton-lead collisions are presented. Quarkonium results from proton-lead collisions are also presented.

Current practices in generation of small molecule new leads.

Science.gov (United States)

Goodnow, R A

2001-01-01

The current drug discovery processes in many pharmaceutical companies require large and growing collections of high quality lead structures for use in high throughput screening assays. Collections of small molecules with diverse structures and "drug-like" properties have, in the past, been acquired by several means: by archive of previous internal lead optimization efforts, by purchase from compound vendors, and by union of separate collections following company mergers. More recently, many drug discovery companies have established dedicated efforts to effect synthesis by internal and/or outsourcing efforts of targeted compound libraries for new lead generation. Although high throughput/combinatorial chemistry is an important component in the process of new lead generation, the selection of library designs for synthesis and the subsequent design of library members has evolved to a new level of challenge and importance. The potential benefits of screening multiple small molecule compound library designs against multiple biological targets offers substantial opportunity to discover new lead structures. Subsequent optimization of such compounds is often accelerated because of the structure-activity relationship (SAR) information encoded in these lead generation libraries. Lead optimization is often facilitated due to the ready applicability of high-throughput chemistry (HTC) methods for follow-up synthesis. Some of the strategies, trends, and critical issues central to the success of lead generation processes are discussed below. Copyright 2002 Wiley-Liss, Inc.

Role of Airborne Lead in Increased Body Burden of Lead in Hartford Children*

Science.gov (United States)

Lepow, Martha L.; Bruckman, Leonard; Rubino, Robert A.; Markowitz, Steven; Gillette, Marybeth; Kapish, Janet

1974-01-01

The ingestion of airborne lead fallout is the mechanism responsible for increased lead body burdens found in 10 urban Connecticut children. The mean indoor lead levels found in housedust was 11,000 μg/g; highest concentrations occurred on windowsills and in floor dust. The mean lead content of Hartford street dirt was 1,200 μg/g; levels were highest near the street and next to the buildings. The mean lead concentration of hand samples taken from the subject children was 2,400 μg/g; the mean weight of hand samples was 11 mg. The concentration of lead in dirt and househould dust was high enough to theoretically result in excessive lead accumulation in young children who are putting their dusty, dirty hands in their mouths during play. While we believe that lead emitted from automobiles contributes significantly to air, dirt and dust lead levels the environmental impact of reducing or eliminating lead from gasoline is not yet completely understood. PMID:4133903

A positive-weight next-to-leading-order Monte Carlo for Z pair hadroproduction

International Nuclear Information System (INIS)

Nason, Paolo; Ridolfi, Giovanni

2006-01-01

We present a first application of a previously published method for the computation of QCD processes that is accurate at next-to-leading order, and that can be interfaced consistently to standard shower Monte Carlo programs. We have considered Z pair production in hadron-hadron collisions, a process whose complexity is sufficient to test the general applicability of the method. We have interfaced our result to the HERWIG and PYTHIA shower Monte Carlo programs. Previous work on next-to-leading order corrections in a shower Monte Carlo (the MC-NLO program) may involve the generation of events with negative weights, that are avoided with the present method. We have compared our results with those obtained with MC-NLO, and found remarkable consistency. Our method can also be used as a standalone, alternative implementation of QCD corrections, with the advantage of positivity, improved convergence, and next-to-leading logarithmic accuracy in the region of small transverse momentum of the radiated parton

Lead Poisoning Prevention Tips

Science.gov (United States)

... or removed safely. How are children exposed to lead? Lead-based paint and lead contaminated dust are ... What can be done to prevent exposure to lead? It is important to determine the construction year ...

The effects of thiamin on lead metabolism: organ distribution of lead 203.

OpenAIRE

Kim, J S; Hamilton, D L; Blakley, B R; Rousseaux, C G

1992-01-01

The effect of thiamin on the organ distribution of lead was evaluated in CD-1 mice exposed intragastrically or intraperitoneally to a single dose of lead acetate (100 micrograms) containing 100 microCi lead 203. They were treated with either thiamin (25 or 50 mg/kg body weight), calcium ethylenediaminetetraacetic acid (CaEDTA) (50 mg/kg body weight), or combinations of thiamin and CaEDTA. The whole body retention and the organ distribution of lead 203 varied depending upon the route of lead a...

An analytically-based method for predicting the noise generated by the interaction between turbulence and a serrated leading edge

Science.gov (United States)

Mathews, J. R.; Peake, N.

2018-05-01

This paper considers the interaction of turbulence with a serrated leading edge. We investigate the noise produced by an aerofoil moving through a turbulent perturbation to uniform flow by considering the scattered pressure from the leading edge. We model the aerofoil as an infinite half plane with a leading edge serration, and develop an analytical model using a Green's function based upon the work of Howe. This allows us to consider both deterministic eddies and synthetic turbulence interacting with the leading edge. We show that it is possible to reduce the noise by using a serrated leading edge compared with a straight edge, but the optimal noise-reducing choice of serration is hard to predict due to the complex interaction. We also consider the effect of angle of attack, and find that in general the serrations are less effective at higher angles of attack.

Soft mode of lead zirconate

International Nuclear Information System (INIS)

Pan'ko, G.F.; Prisedskij, V.V.; Klimov, V.V.

1983-01-01

Anisotropic diffusional scattering of electrons on PbZrO 3 crystal in the temperature range of phase transition has been recorded. As a result of its analysis it has been established that in lead zirconate the rotational vibrational mode G 25 plays the role of soft mode. The experiment is carried out using PbZrO 3 monocrystals in translucent electron microscope EhM-200, operating in the regime of microdiffraction at accelerating voltage of 150 kV and beam current 50 μA; sample preparation is realized using the method of shearing and fragmentation

A cloud computing based 12-lead ECG telemedicine service

Science.gov (United States)

2012-01-01

Background Due to the great variability of 12-lead ECG instruments and medical specialists’ interpretation skills, it remains a challenge to deliver rapid and accurate 12-lead ECG reports with senior cardiologists’ decision making support in emergency telecardiology. Methods We create a new cloud and pervasive computing based 12-lead Electrocardiography (ECG) service to realize ubiquitous 12-lead ECG tele-diagnosis. Results This developed service enables ECG to be transmitted and interpreted via mobile phones. That is, tele-consultation can take place while the patient is on the ambulance, between the onsite clinicians and the off-site senior cardiologists, or among hospitals. Most importantly, this developed service is convenient, efficient, and inexpensive. Conclusions This cloud computing based ECG tele-consultation service expands the traditional 12-lead ECG applications onto the collaboration of clinicians at different locations or among hospitals. In short, this service can greatly improve medical service quality and efficiency, especially for patients in rural areas. This service has been evaluated and proved to be useful by cardiologists in Taiwan. PMID:22838382

A cloud computing based 12-lead ECG telemedicine service

Directory of Open Access Journals (Sweden)

Hsieh Jui-chien

2012-07-01

Full Text Available Abstract Background Due to the great variability of 12-lead ECG instruments and medical specialists’ interpretation skills, it remains a challenge to deliver rapid and accurate 12-lead ECG reports with senior cardiologists’ decision making support in emergency telecardiology. Methods We create a new cloud and pervasive computing based 12-lead Electrocardiography (ECG service to realize ubiquitous 12-lead ECG tele-diagnosis. Results This developed service enables ECG to be transmitted and interpreted via mobile phones. That is, tele-consultation can take place while the patient is on the ambulance, between the onsite clinicians and the off-site senior cardiologists, or among hospitals. Most importantly, this developed service is convenient, efficient, and inexpensive. Conclusions This cloud computing based ECG tele-consultation service expands the traditional 12-lead ECG applications onto the collaboration of clinicians at different locations or among hospitals. In short, this service can greatly improve medical service quality and efficiency, especially for patients in rural areas. This service has been evaluated and proved to be useful by cardiologists in Taiwan.

Activity of lead deposited in the tissues in conditions of occupational lead exposure

Energy Technology Data Exchange (ETDEWEB)

1974-01-01

The author measured urinary excretion of delta-aminolevulinic acid (ALA), coproporphyrins and lead, before and after administration of chelating agents (CaEDTA and D-penicillamine) to subjects presenting clinical symptoms of lead poisoning and workers occupationally exposed to lead. He found a great increase in lead following its mobilization in subjects with lead poisoning who had previously shown a high level of haemoglobin precursors and a low urinary lead level. In these subjects ALA excretion was proportional to the duration of exposure. A correlation was found between urinary ALA and coproporphyrins, on the one hand, and lead excretion after provocation, on the other. This suggests that the lead deposited in the tissues, as well as that in circulation, retains all its activity.

Eco-Balance analysis of the disused lead-acid-batteries recycling technology

Science.gov (United States)

Kamińska, Ewa; Kamiński, Tomasz

2017-10-01

The article presents the results of the eco-balance analysis of the disused lead-acid batteries recycling process. Test-dedicated technology offers the possibility to recover other elements, for example, polypropylene of the battery case or to obtain crystalline sodium sulphate. The life cycle assessment was made using ReCiPe and IMPACT2002 + methods. The results are shown as environmental points [Pt]. The results are shown in the environmental categories, specific for each of the methods grouped in the impact categories. 1 Mg of the processed srap was a dopted as the functional unit. The results of the analyses indicate that recycling processes may provide the environmental impact of recycling technology less harmful. Repeated use of lead causes that its original sources are not explored. Similarly, the use of granule production-dedicated polypropylene extracted from battery casings that are used in the plastics industry, has environmental benefits. Due to the widespread use of lead-acid batteries, the attention should be paid to their proper utilization, especially in terms of heavy metals, especially lead. According to the calculations, the highest level of environmental benefits from the use of lead from secondary sources in the production of new products, was observed in the refining process.

Eco-Balance analysis of the disused lead-acid-batteries recycling technology

Directory of Open Access Journals (Sweden)

Kamińska Ewa

2017-01-01

Full Text Available The article presents the results of the eco-balance analysis of the disused lead-acid batteries recycling process. Test-dedicated technology offers the possibility to recover other elements, for example, polypropylene of the battery case or to obtain crystalline sodium sulphate. The life cycle assessment was made using ReCiPe and IMPACT2002 + methods. The results are shown as environmental points [Pt]. The results are shown in the environmental categories, specific for each of the methods grouped in the impact categories. 1 Mg of the processed srap was a dopted as the functional unit. The results of the analyses indicate that recycling processes may provide the environmental impact of recycling technology less harmful. Repeated use of lead causes that its original sources are not explored. Similarly, the use of granule production-dedicated polypropylene extracted from battery casings that are used in the plastics industry, has environmental benefits. Due to the widespread use of lead-acid batteries, the attention should be paid to their proper utilization, especially in terms of heavy metals, especially lead. According to the calculations, the highest level of environmental benefits from the use of lead from secondary sources in the production of new products, was observed in the refining process.

Health care of people at work. Workers exposed to lead. I. Inorganic lead

Energy Technology Data Exchange (ETDEWEB)

Waldron, H.A.

1978-01-01

The risks associated with exposure to inorganic lead and the means by which these risks can be minimized are outlined. Lead is used to make a variety of metal products, the grids and oxides in storage batteries, pigments, chemicals, and also for lead plating. In the United States about 70% of the total lead consumption is related to transportation. Uptake of inorganic lead is by ingestion and inhalation. About 90% of the total body burden of lead is contained within the skeletal tissues. Lead is excreted in the kidney, in sweat, and in milk. Toxic effects are directed against the blood, the nervous system, and the kidney. Symptoms of lead poisoning are abdominal pain, constipation, vomiting, asthenia, paresthesia, psychological symptoms, and diarrhea. Physical and biological monitoring can serve to protect workers. Diagnosis of lead poisoning is not easy. Treatment involves removal from exposure and/or treatment with a chelating agent.

Leading Democratically

Science.gov (United States)

Brookfield, Stephen

2010-01-01

Democracy is the most venerated of American ideas, the one for which wars are fought and people die. So most people would probably agree that leaders should be able to lead well in a democratic society. Yet, genuinely democratic leadership is a relative rarity. Leading democratically means viewing leadership as a function or process, rather than…

Who Leads China's Leading Universities?

Science.gov (United States)

Huang, Futao

2017-01-01

This study attempts to identify the major characteristics of two different groups of institutional leaders in China's leading universities. The study begins with a review of relevant literature and theory. Then, there is a brief introduction to the selection of party secretaries, deputy secretaries, presidents and vice presidents in leading…

Assessment of Copper, Cadmium and Lead in Organical Matrix

International Nuclear Information System (INIS)

Gutierrez, Ariel

2000-08-01

In this report the electrochemical method of differential pulse anode voltametry redisolution voltametry is used to quantitative assessment of copper, cadmium and lead in solution. The methodology is described in the preparation of samples for measurement

Atomic absorption spectrometric determination of copper, zinc, and lead in geological materials

Science.gov (United States)

Sanzolone, R.F.; Chao, T.T.

1976-01-01

An atomic absorption spectrometric method is described for the determination of copper, zinc, and lead in geological materials. The sample is digested with HF-HCl-H2O2; the final solution for analysis is in 10 % (v/v) HCl. Copper and zinc are determined directly by aspirating the solution into an air-acetylene flame. A separate aliquot of the solution is used for determination of lead; lead is extracted into TOPO-MIBK from the acidic solution in the presence of iodide and ascorbic acid. For a 0.50-g sample, the limits of determination are 10-2000 p.p.m. for Cu and Zn, and 5-5000 p.p.m. for Pb. As much as 40 % Fe or Ca. and 10 % Al, Mg, or Mn in the sample do not interfere. The proposed method can be applied to the determination of copper, zinc, and lead in a wide range of geological materials including iron- and manganese-rich, calcareous and carbonate samples. ?? 1976.

Lead theft--a study of the "uniqueness" of lead from church roofs.

Science.gov (United States)

Bond, John W; Hainsworth, Sarah V; Lau, Tien L

2013-07-01

In the United Kingdom, theft of lead is common, particularly from churches and other public buildings with lead roofs. To assess the potential to distinguish lead from different sources, 41 samples of lead from 24 church roofs in Northamptonshire, U.K, have been analyzed for relative abundance of trace elements and isotopes of lead using X-ray fluorescence (XRF) and inductively coupled plasma mass spectrometry, respectively. XRF revealed the overall presence of 12 trace elements with the four most abundant, calcium, phosphorus, silicon, and sulfur, showing a large weight percentage standard error of the mean of all samples suggesting variation in the weight percentage of these elements between different church roofs. Multiple samples from the same roofs, but different lead sheets, showed much lower weight percentage standard errors of the mean suggesting similar trace element concentrations. Lead isotope ratios were similar for all samples. Factors likely to affect the occurrence of these trace elements are discussed. © 2013 American Academy of Forensic Sciences.

Contribution to the study of the geophysical behaviour of lead-210 by application of alpha spectrometry

International Nuclear Information System (INIS)

Nezami, M.

1965-06-01

A study of the changes in the lead-210 contents of rain-water and of water produced by melting polar ice has required the development of a method for dosing lead-210, an α emitter. This method is 40 times more sensitive than that which measures the lead-210 by bismuth-210, a (β emitter. The first part of the report presents the study of a spectrometry using semiconductor detectors; a catalogue of a spectra shows the advantages of this method. In the second part will be found at first a new chemical separation method for polonium-210 and the results obtained with this method. The main results obtained on the geophysical behaviour of lead-210 are the following: - the monthly lead-210 and polonium-210 contents in rain water are approximately constant with time. - in the Gif-sur-Yvette region, the clean-up by 'dry fall-out' can attain 40 to 50 per cent of the total fall-out. - a study of Antarctic ice samples makes it possible to determine an annual accumulation rate equivalent to 13.8 cm of water and to show discrepancies in the periodic concentrations which correspond to the latest maxima of solar activity. - a balance is drawn up between the radon produced by the continents and the lead-210 fall-out. (author) [fr

Quantification of atmospheric lead emissions from 70 years of leaded petrol consumption in Australia

Science.gov (United States)

Kristensen, Louise Jane

2015-06-01

Lead is a persistent pollutant and the subject of many environmental studies, yet, in Australia, the extent of atmospheric lead emissions from the use of leaded petrol is unquantified. This paper details the first comprehensive account of leaded petrol sales and its lead concentrations over the 70 years of use in Australia. The resulting atmospheric lead emissions are calculated to provide the most complete understanding of the volume of lead released to the Australian continent from the consumption of leaded petrol. Atmospheric emissions of lead to the entire Australian continent from leaded petrol are calculated to total 240,510 tonnes over seven decades of use, peaking at 7869 tonnes in 1974. Total emissions for individual states and territories range from 1745 to 67,893 tonnes, with New South Wales responsible for the largest emissions. The effect of regulations on allowable concentrations of tetraethyl-lead additives are observed in the reduction of lead emissions in New South Wales and Victoria. The consequences to human health and the environment of leaded petrol consumption in Australia's populous cities are examined against historical air quality data and blood lead levels.

Penetration of a magnetic field into superconducting lead and lead-indium alloys

International Nuclear Information System (INIS)

Egloff, C.; Raychaudhuri, A.K.; Rinderer, L.

1983-01-01

The temperature dependence of the magnetic field penetration depth of superconducting lead and lead-indium alloys has been studied over the temperature range between about 2 K and T/sub c/. Data are analyzed in terms of the microscopic theory. The difficulties of a unique analysis of the penetration data are pointed out and a strategy for the analysis is discussed. The penetration depth at T = 0K for pure lead is determined as 522 A. This value, though higher than the previously accepted value for lead, is nevertheless consistent with the strong coupling character of lead

Lead inclusions in aluminium

International Nuclear Information System (INIS)

Johnson, E.; Johansen, A.; Sarholt-Kristensen, L.; Andersen, H.H.; Grabaek, L.; Bohr, J.

1990-01-01

Ion implantation at room temperature of lead into aluminum leads to spontaneous phase separation and formation of lead precipitates growing topotactically with the matrix. Unlike the highly pressurized (∼ 1-5 GPa) solid inclusions formed after noble gas implantations, the pressure in the lead precipitates is found to be less than 0.12 GPa. Recently the authors have observed the result that the lead inclusions in aluminum exhibit both superheating and supercooling. In this paper they review and elaborate on these results. Small implantation-induced lead precipitates embedded in an aluminum matrix were studied by x-ray diffraction

EP toxicity testing of lead to resolve disposition of radioactively contaminated lead

International Nuclear Information System (INIS)

Larsen, M.M.; Boehmer, A.M.

1986-03-01

The Department of Energy (DOE), in its efforts to comply with the requirements of the Resource Conservation and Recovery Act (RCRA) of 1976, is concerned with hazardous waste which is also radioactively contaminated. There are no existing facilities to treat or dispose of these wastes. One such waste is lead, which is extensively used in the nuclear industry as shielding. This paper reports the results of leach testing of lead (both solid lead samples and lead shot) to resolve questions as to whether or not radioactively contaminated waste lead must be treated as a hazardous waste. The results of these tests showed that: some samples passed the leach test. Results of development efforts performed to date to recycle lead and those planned for the future are included in this report

Lead content of deciduous tooth enamel from high-radon area

International Nuclear Information System (INIS)

Anttila, A.

1987-01-01

Lead concentrations in the enamel of deciduous incisors of 49 6- to 7-year children living in Askola, a rural area in which the radon level is one og the highest in Finland, were determined by the proton-induced X-ray emission method. The absolute concentrations were obtained by calibration with the animal bone standard of the International Atomic Energy Agency. The mean lead concentration of 8.8±6.6 ppm of the whole enamel agreed well with the earlier corresponding lead data from other regions of Finland, indicating that no significant increase in the lead level of the teeth would have occurred because of radon decay. However, the lead concentration level measured on the tooth surface was somewhat higher in Askola, 232±141 ppm, than in the low-radon area Oulu (167±139 ppm; ρ<0.10). The lead concentration of the whole enamel of the upper incisors, 12.2 ± 8.0 ppm, was twice as high as that of the lower incisors, 6.8 ± 4.6 ppm (ρ<0.005), emphasizing the importance of classifying lead concentration data by tooth type

Elution of lead from lead zirconate titanate ceramics to acid rain

Science.gov (United States)

Tsurumi, Takaaki; Takezawa, Shuhei; Hoshina, Takuya; Takeda, Hiroaki

2017-10-01

The amount of lead that eluted from lead zirconate titanate (PZT) ceramics to artificial acid rain was evaluated. Four kinds of PZT ceramics, namely, pure PZT at MPB composition, CuO-added PZT, PZT with 10 mol % substitution of Ba for Pb, and CuO-added PZT with 10 mol % substitution of Ba for Pb, were used as samples of the elution test. These PZT ceramics of 8 mm2 and 1.1-1.2 mm thickness were suspended in 300 ml of H2SO4 solution of pH 4.0. The concentration of lead eluted from PZT was in the range from 0.2 to 0.8 ppm. It was found that both liquid phase formation by the addition of CuO and the substitution of Ba for Pb were effective to reduce the amount of lead that eluted. By fitting the leaching out curve with a classical equation, a master curve assuming no sampling effect was obtained. The lead concentration evaluated from the amount of lead that eluted from a commercial PZT plate to H2SO4 solution of pH 5.3 was almost the same as the limit in city water. It is concluded that PZT is not harmful to health and the environment and the amount of lead that eluted from PZT can be controlled by modifying PZT composition.

Heart rate variability in workers chronically exposed to lead.

Science.gov (United States)

Gajek, Jacek; Zyśko, Dorota; Chlebda, Ewa

2004-07-01

Lead is a strong neurotoxin. The effects of lead on the activity of the autonomic nervous system, assessed by the use of heart rate variability (HRV) analysis, have not yet been established. To assess the effects of occupational chronic lead exposure on the autonomic nervous system activity. The study group consisted of 22 copper foundry workers (mean age 41.8+/-8.7 years) who had elevated parameters of lead overload and were admitted to the hospital for chelate therapy. The control group consisted of 13 age-matched healthy males. Lead concentration was measured with the use of atomic absorption spectrophotometry, and concentration of free protoporphyrins in erythrocytes (FEP) using a fluorometric method. Each patient underwent 24-hour ambulatory ECG monitoring, and standard short-term as well as long-term HRV parameters were obtained. There were no significant differences between patients and controls in HRV parameters. In the control group, HRV parameters correlated with age. In patients, a significant negative correlation between lead concentration and some short-term HRV parameters calculated during the night was found: SDNN (r=-0.48, p<0.05), TP (r=-0.48, p<0.01) and LF (r=-0.48, p<0.01). In patients, a negative correlation between lead concentration and HFnight/HFday index was found (r=-0.47 p<0.01), whereas in controls this correlation was positive (r=0.66 p<0.05). Overall HRV indices are similar in subjects exposed to lead and in healthy controls. A decrease in the physiological elevation of HF values during the night, together with an increase in lead blood concentration and lack of relationship between age and HRV parameters in workers chronically exposed to lead may suggest disturbances of the autonomic system. In subjects not exposed to lead a decrease in heart rate with an increase in FEP concentration was observed.

Long range correlations, leading particle spectrum and correlations with leading particles

International Nuclear Information System (INIS)

Ilgenfritz, E.M.

1976-05-01

The unitary cluster emission model by de Groot and Ruijgrok is discussed as an approach to understand the leading particle behaviour. Consequences of the model concerning co--rrelations between leading particles and produced particles in the central region are considered. No satisfactory agreement was found. Production of leading clusters is argued for being an essential feature of these correlations. (author)

Lead Tolerance and Accumulation in White Poplar Cultivated In Vitro

Directory of Open Access Journals (Sweden)

Branislav Kovačević

2013-06-01

Full Text Available Background and Purpose: This paper analyses the lead tolerance and accumulation in white poplar genotypes in vitro, in order to optimize genotype evaluation and other procedures in their implementation in phytoremediation projects and landscaping in areas endangered by lead accumulation. Material and Methods: The lead tolerance and accumulation of five white poplar genotypes after 35 days in vitro cultivation on media supplemented with lead was examined. The following Pb(NO32 concentrations were used: 0, 10-6, 10-5, 10-4 and 10-3 M. Tolerance analysis (described by tolerance indices was based on morphological parameters, biomass accumulation and the content of photosynthetic pigments, while lead accumulation was described by shoot lead accumulation and shoot lead content. Results and Conclusions: The chosen lead concentrations appeared not to be lethal. Moreover, the obtained results showed that the tested lead concentrations had a positive effect on: number of formed roots, shoot moisture content and shoot height. The best differentiation among the examined genotypes was gained by the tolerance index based on the shoot height on 10-4 M Pb(NO32. The shoot lead accumulation and shoot lead content significantly increased on 10-4 and 10-3 M Pb(NO32 media. Thus, the concentration of 10-4 M Pb(NO32 is recommended for further research. Two examined genotypes of horticultural value (LCM and LBM achieved a significantly higher lead shoot content compared to the wide spread genotype “Villafranca” (almost 200% and 125% higher, respectively.

Examination of optimal radiation quality in the lead equivalent examination of x-ray protective clothing

International Nuclear Information System (INIS)

Inoue, Shinichi; Matsuzawa, Rie; Matsumoto, Mitsuhiro

2004-01-01

The objective of this study was to determine the effective lead thickness of the apron for radiation protective clothing, i.e., the lead equivalent, a method of performing the lead equivalent examination is provided in the Japanese Industrial Standards (JIS). We proposed a method of computation using an attenuation coefficient, and examined the measurement accuracy and optimal radiation quality using both. We were able to compute the lead equivalent with sufficient accuracy when using radiation quality of about 60 keV in the range of radiation quality examined. This technique was also examined in the measurement used for the marketing of radiation protective clothing. (author)

Working towards accreditation by the International Standards Organization 15189 Standard: how to validate an in-house developed method an example of lead determination in whole blood by electrothermal atomic absorption spectrometry.

Science.gov (United States)

Garcia Hejl, Carine; Ramirez, Jose Manuel; Vest, Philippe; Chianea, Denis; Renard, Christophe

2014-09-01

Laboratories working towards accreditation by the International Standards Organization (ISO) 15189 standard are required to demonstrate the validity of their analytical methods. The different guidelines set by various accreditation organizations make it difficult to provide objective evidence that an in-house method is fit for the intended purpose. Besides, the required performance characteristics tests and acceptance criteria are not always detailed. The laboratory must choose the most suitable validation protocol and set the acceptance criteria. Therefore, we propose a validation protocol to evaluate the performance of an in-house method. As an example, we validated the process for the detection and quantification of lead in whole blood by electrothermal absorption spectrometry. The fundamental parameters tested were, selectivity, calibration model, precision, accuracy (and uncertainty of measurement), contamination, stability of the sample, reference interval, and analytical interference. We have developed a protocol that has been applied successfully to quantify lead in whole blood by electrothermal atomic absorption spectrometry (ETAAS). In particular, our method is selective, linear, accurate, and precise, making it suitable for use in routine diagnostics.

Comparative toxicity of tetra ethyl lead and lead oxide to earthworms, Eisenia fetida (Savigny)

International Nuclear Information System (INIS)

Venkateswara Rao, J.; Kavitha, P.; Padmanabha Rao, A.

2003-01-01

Leaded gasoline contains tetra ethyl lead (TEL) as an antiknocking agent, which produces major amounts of lead oxide in automobile exhaust along with traces of TEL. To minimize the lead contamination, methyl tertiary butyl ether (MTBE) is used as a substitute for producing unleaded gasoline. It has become increasingly apparent that young children are highly susceptible to the harmful effects of lead. Hence, a study was carried out to monitor lead toxicity in soil, using adult earthworms (Eisenia fetida, Savigny). Leaded gasoline (TEL) and lead oxide are 383- and 211-fold more toxic than unleaded gasoline (MTBE) in 7 days of exposure and 627- and 290-fold more toxic in 14 days, respectively. Results indicate that the presence of TEL in leaded gasoline and lead oxide has a significant effect on behavior, morphology, and histopathology of earthworms. Absorption of TEL into the tissues is comparatively less than that of lead oxide but toxic effects were severe. Rupture of the cuticle, extrusion of coelomic fluid and inflexible metameric segmentation were observed, causing desensitization of the posterior region leading to fragmentation in earthworms

Lead-resistant Providencia alcalifaciens strain 2EA bioprecipitates Pb+2 as lead phosphate.

Science.gov (United States)

Naik, M M; Khanolkar, D; Dubey, S K

2013-02-01

A lead-resistant bacteria isolated from soil contaminated with car battery waste were identified as Providencia alcalifaciens based on biochemical characteristics, FAME profile and 16S rRNA sequencing and designated as strain 2EA. It resists lead nitrate up to 0·0014 mol l(-1) by precipitating soluble lead as insoluble light brown solid. Scanning electron microscopy coupled with energy-dispersive X-ray spectrometric analysis (SEM-EDX) and X-ray diffraction spectroscopy (XRD) revealed extracellular light brown precipitate as lead orthophosphate mineral, that is, Pb(9) (PO(4))(6) catalysed by phosphatase enzyme. This lead-resistant bacterial strain also demonstrated tolerance to high levels of cadmium and mercury along with multiple antibiotic resistance. Providencia alcalifaciens strain 2EA could be used for bioremediation of lead-contaminated environmental sites, as it can efficiently precipitate lead as lead phosphate. © 2012 The Society for Applied Microbiology.

Spirulina platensis feeding inhibited the anemia- and leucopenia-induced lead and cadmium in rats

Energy Technology Data Exchange (ETDEWEB)

Simsek, Nejdet [University of Atatuerk, Faculty of Veterinary Medicine, Department of Histology and Embryology, 25700 Erzurum (Turkey); Karadeniz, Ali, E-mail: karadenizali@gmail.com [University of Atatuerk, Faculty of Veterinary Medicine, Department of Physiology, 25700 Erzurum (Turkey); Kalkan, Yildiray; Keles, Osman N.; Unal, Buenyami [University of Atatuerk, Faculty of Medicine, Department of Histology and Embryology, 25240 Erzurum (Turkey)

2009-05-30

In the present investigation, the effect of Spirulina platensis (Sp) was undertaken on rats fed with lead and cadmium including diet by using physiological, enzymehistochemical and stereological methods. For this aim, 50 rats were equally divided into five groups as control (C), lead (Pb), Spirulina + lead (Sp + Pb), cadmium (Cd), and Spirulina + cadmium (Sp + Cd). Red blood cell (RBC) and white blood cell (WBC) counts, packed cell volume (PCV), and haemoglobine (Hb) concentrations were determined by haemocytometric methods in blood samples collected on 30th day. Population of T lymphocyte was counted by the {alpha}-naphthyl acetate esterase (ANAE) staining method, and reticulocytes were counted by stereological method. The counts of RBC, WBC, and ANAE positive T lymphocyte, and the values of Hb, PCV, and MCHC were decreased in the Pb and Cd groups compared to control group. Also, the number of reticulocytes (polychromatofilic erythrocyte) increased in the Pb groups, whereas it decreased in the Cd group. On the other hand, these values were ceased by S. platensis in the treated groups. These results suggest that S. platensis supplementation may be useful in adjuvant treatment of leukemia and anemia caused by lead and cadmium toxication.

Lead isotopes in soils near five historic American lead smelters and refineries

International Nuclear Information System (INIS)

Rabinowitz, Michael B.

2005-01-01

This survey of soil lead in the vicinity of old industrial sites examines how the stable isotope patterns vary among the sites according to the sources of the lead ore processed at each site. Lead smelters and refineries, which closed down decades ago, are the basis of this investigation. Samples were taken from near five old factory sites in Collinsville and Alton (Illinois), Ponderay (Idaho), East Chicago (Indiana) and Omaha (Nebraska). Historical records were searched for accounts of the sources of the lead. Lead concentrations were measured by atomic absorption flame spectrophotometry, and stable isotopic analysis was done by plasma ionization mass spectrometry. At every site visited, remnants of the old factories, in terms of soil lead pollution, could be found. In spite of potential complications of varying smelter feedstock sourced from mines of different geological age, it was possible to match the isotopic patterns in the soils with the documented sources of the ores. The Collinsville and Alton sites resembled Missouri lead. The Ponderay value was higher than major Bunker Hill, Idaho deposits, but closer to the minor, nearby Oreille County, Washington ores. Mostly Utah ore was used in East Chicago. The Omaha soil reflects lead from Mexico, Colorado and Montana

The void nucleation mechanism within lead phase during spallation of leaded brass

Science.gov (United States)

Yang, Yang; Wang, Can; Chen, Xingzhi; Chen, Kaiguo; Hu, Haibo; Fu, Yanan

2018-07-01

The incipient spall behaviours of Cu-34%Zn-3%Pb leaded brass samples with annealed and cryogenic-treated conditions were loaded using one-stage light gas gun experiments. The effect of Pb-phase on dynamic damage nucleation in leaded brass specimens was investigated by means of optical microscopy, scanning electron microscopy and x-ray computer tomography. It was found that the voids of incipient spall were mainly nucleated in the interior of the lead (no tensile stress would be produced within lead according to the impact theory) instead of nucleated at the phase interface as expected by quasi-static damage fracture theory. A nucleation model is proposed in the present work that is the asymmetry high compression zones in the centre of the lead-phase were formed by the rarefaction wave convergence effects of matrix/quasi-spherical lead interface, which caused adiabatic temperature rise that exceeded melting point of lead due to severe plastic deformation, finally led to local melting and void nucleation. In addition, the spall strength and damage rate increased with the increase in the Pb-phase number.

Lead toxicity on hematological parameters in workers with occupational exposure to lead

International Nuclear Information System (INIS)

Dursun, N.; Koese, K.

1998-01-01

The effects of lead on hematological parameters were studied in lead exposed male workers occupied for 17.84+-4.22 years in a metal powder producing factory in Kayseri, Turkey and control male workers in same city. Blood lead and plasma zinc levels were measured by Atomic Absorption Spectrophotometry (AAS) and hematological parameters by Culture Counter S. The lead exposure workers had higher lead levels (13.81+- 9.21 mug/dl) as compared to control subjects (2.37+-0.10 mug/dl). No difference was observed in the plasma zinc levels of both groups. As indices of lead exposure, red blood cell (RBC) counts, hemoglobin (Hb), and hematocrit (Hct) values significantly decreased. Mean corpuscular volume (MCV), mean corpuscular hemoglobin (MCH), and mean corpuscular haemoglobin concentration (MCHC) significantly increased except MCV. There was also an increase in MCV, but it was not significant. (author)

Lead-free piezoelectric materials and ultrasonic transducers for medical imaging

Directory of Open Access Journals (Sweden)

Elaheh Taghaddos

2015-06-01

Full Text Available Piezoelectric materials have been vastly used in ultrasonic transducers for medical imaging. In this paper, firstly, the most promising lead-free compositions with perovskite structure for medical imaging applications have been reviewed. The electromechanical properties of various lead-free ceramics, composites, and single crystals based on barium titanate, bismuth sodium titanate, potassium sodium niobate, and lithium niobate are presented. Then, fundamental principles and design considerations of ultrasonic transducers are briefly described. Finally, recent developments in lead-free ultrasonic probes are discussed and their acoustic performance is compared to lead-based transducers. Focused transducers with different beam focusing methods such as lens focusing and mechanical shaping are explained. Additionally, acoustic characteristics of lead-free probes including the pulse-echo results as well as their imaging capabilities for various applications such as phantom imaging, in vitro intravascular ultrasound imaging of swine aorta, and in vivo or ex vivo imaging of human eyes and skin are reviewed.

Monetary benefits of preventing childhood lead poisoning with lead-safe window replacement

OpenAIRE

Nevin, Rick; Jacobs, David / E.; Berg, Michael; Cohen, Jonathan

2007-01-01

Previous estimates of childhood lead poisoning prevention benefits have quantified the present value of some health benefits, but not the costs of lead paint hazard control or the benefits associated with housing and energy markets. Because older housing with lead paint constitutes the main exposure source today in the U.S., we quantify health benefits, costs, market value benefits, energy savings, and net economic benefits of lead-safe window replacement (which includes paint stabilization ...

Study on corrosion test techniques in lead bismuth eutectic flow. Joint research report in JFY2002

International Nuclear Information System (INIS)

Takahashi, Minoru; Sekimoto, Hiroshi

2003-03-01

The evaluation of corrosion behaviors of core and structural materials in lead bismuth eutectic is one of the key issues for the utilization of lead bismuth eutectic as a coolant of the primary loops of lead bismuth cooled fast breeder reactors (FBRs) and the intermediate heat transport media of new-type steam generators of the sodium cooled FBRs. The purpose of the present study is to establish corrosion test techniques in lead bismuth eutectic flow. The techniques of steel corrosion test and oxygen control in flowing lead bismuth eutectic, and the technologies of a lead bismuth flow test at high temperature and high velocity were developed through corrosion test using a lead bismuth flow test loop of the Tokyo Institute of Technology in JFY2002. The major results are summarized as follows: (1) Techniques of fabrication, mount and rinse of corrosion specimens, measurement method of weight loss, and SEM/EDX analysis method have been established through lead bismuth corrosion test. (2) Weight losses were measured, corrosion and lead bismuth-adhered layers and eroded parts were observed in two 1000 hr-corrosion tests, and the results were compared with each other for twelve existing steels including ODS, F82H and SUH-3. (3) An oxygen sensor made of zirconia electrolyte structurally resistant to thermal stress and thermal shock was developed and tested in the lead bismuth flow loop. Good performance has been obtained. (4) An oxygen control method by injecting argon and hydrogen mixture gas containing steam into lead bismuth was applied to the lead bismuth flow loop, and technical issues for the development of the oxygen control method were extracted. (5) Technical measures for freezing and leakage of lead bismuth in the flow loop were accumulated. (6) Technical measures for flow rate decrease/blockage due to precipitation of oxide and corrosion products in a low temperature section of the lead bismuth flow loop were accumulated. (7) Electromagnetic flow meters with MI

Pacemaker lead fracture without an increase in lead impedance caused by cardiac fibroma

Directory of Open Access Journals (Sweden)

Daisuke Sato

2013-12-01

Full Text Available We report the case of a 64-year-old man who had a permanent pacemaker with a unipolar silicone electrode positioned in the right ventricle in 1989 for sinus node dysfunction. On a routine checkup in June 2011, a 28-mm-diameter mass was discovered, which appeared to adhere to the tricuspid valve and the ventricular lead. The size of the mass did not change for the next 6 months, and the lead impedance was maintained at around 500–600 Ω. Because pacing failure was observed in January 2012, he underwent an urgent pacemaker check; however, the lead impedance was found not to have increased greatly (689 Ω. Nevertheless, the pacemaker lead was noted to be fractured at the tricuspid level. His echocardiogram showed new severe tricuspid regurgitation and a floating mass around the lead. We extracted the fractured lead, enucleated the tumor, replaced the tricuspid valve, and placed an epicardial lead. Macroscopic examination revealed that the tumor surrounded the fractured lead and covered the stump. Pathological examination revealed that the tumor was composed of fibrous connective tissue. We presumed that electric current continued to flow through the stump of the fractured unipolar lead to the generator, and this might have caused the limited increase in lead impedance.

Extraction of lead and ridge characteristics from SAR images of sea ice

Science.gov (United States)

Vesecky, John F.; Smith, Martha P.; Samadani, Ramin

1990-01-01

Image-processing techniques for extracting the characteristics of lead and pressure ridge features in SAR images of sea ice are reported. The methods are applied to a SAR image of the Beaufort Sea collected from the Seasat satellite on October 3, 1978. Estimates of lead and ridge statistics are made, e.g., lead and ridge density (number of lead or ridge pixels per unit area of image) and the distribution of lead area and orientation as well as ridge length and orientation. The information derived is useful in both ice science and polar operations for such applications as albedo and heat and momentum transfer estimates, as well as ship routing and offshore engineering.

Highly reversible lead-carbon battery anode with lead grafting on the carbon surface

KAUST Repository

Yin, Jian; Lin, Nan; Zhang, Wenli; Lin, Zheqi; Zhang, Ziqing; Wang, Yue; Shi, Jun; Bao, Jinpeng; Lin, Haibo

2018-01-01

A novel C/Pb composite has been successfully prepared by electroless plating to reduce the hydrogen evolution and achieve the high reversibility of the anode of lead-carbon battery (LCB). The deposited lead on the surface of C/Pb composite was found to be uniform and adherent to carbon surface. Because lead has been stuck on the surface of C/Pb composite, the embedded structure suppresses the hydrogen evolution of lead-carbon anode and strengthens the connection between carbon additive and sponge lead. Compared with the blank anode, the lead-carbon anode with C/Pb composite displays excellent charge–discharge reversibility, which is attributed to the good connection between carbon additives and lead that has been stuck on the surface of C/Pb composite during the preparation process. The addition of C/Pb composite maintains a solid anode structure with high specific surface area and power volume, and thereby, it plays a significant role in the highly reversible lead-carbon anode.

Highly reversible lead-carbon battery anode with lead grafting on the carbon surface

KAUST Repository

Yin, Jian

2018-03-27

A novel C/Pb composite has been successfully prepared by electroless plating to reduce the hydrogen evolution and achieve the high reversibility of the anode of lead-carbon battery (LCB). The deposited lead on the surface of C/Pb composite was found to be uniform and adherent to carbon surface. Because lead has been stuck on the surface of C/Pb composite, the embedded structure suppresses the hydrogen evolution of lead-carbon anode and strengthens the connection between carbon additive and sponge lead. Compared with the blank anode, the lead-carbon anode with C/Pb composite displays excellent charge–discharge reversibility, which is attributed to the good connection between carbon additives and lead that has been stuck on the surface of C/Pb composite during the preparation process. The addition of C/Pb composite maintains a solid anode structure with high specific surface area and power volume, and thereby, it plays a significant role in the highly reversible lead-carbon anode.

Impact of lead tolerant plant growth promoting rhizobacteria on growth, physiology, antioxidant activities, yield and lead content in sunflower in lead contaminated soil.

Science.gov (United States)

Saleem, Muhammad; Asghar, Hafiz Naeem; Zahir, Zahir Ahmad; Shahid, Muhammad

2018-03-01

Present study was conducted to evaluate the effect of lead tolerant plant growth promoting rhizobacteria (LTPGPR) on growth, physiology, yield, antioxidant activities and lead uptake in sunflower in soil contaminated with lead under pot conditions. Three pre-characterized LTPGP strains (S2 (Pseudomonas gessardii strain BLP141), S5 (Pseudomonas fluorescens A506) and S10 (Pseudomonas fluorescens strain LMG 2189)) were used to inoculate sunflower growing in soil contaminated with different levels (300, 600 and 900 mg kg -1 ) of lead by using lead nitrate salt as source of lead. Treatments were arranged according to completely randomized design with factorial arrangements. At harvesting, data regarding growth attributes (root shoot length, root shoot fresh and dry weights), yield per plant, physiological attributes (Chlorophyll 'a', 'b' and carotenoids content), antioxidant activities (Ascorbate peroxidase, catalase, superoxide dismutase and glutathione reductase), proline and malanodialdehyde content, and lead content in root, shoot and achenes of sunflower were recorded. Data were analysed by standard statistical procedures. Results showed that lead contamination reduced the plants growth, physiology and yield at all levels of lead stress. But application of LTPGPR in soil contaminated with lead improved plant growth, physiology, yield, and antioxidant activities, proline, and reduced the malanodialdehyde content (that is reduced by the application of different strains in lead contamination) of sunflower as compared to plants grown in soil without inoculation. Inoculation also promoted the uptake of lead in root, shoots and reduced the uptake of lead in achenes of plants as compared to plants in lead contamination without inoculation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Lead and silver extraction from waste cake from hydrometallurgical zinc production

Directory of Open Access Journals (Sweden)

DUSAN D. STANOJEVIC

2008-05-01

Full Text Available This paper presents the experimental results of the extraction of lead and silver from a lead–silver waste cake obtained in the process of hydrometallurgical zinc production. While controlling the pH value, the lead–silver cake was leached at a temperature close to boiling point in different concentrations of aqueous calcium chloride solutions. The experiments were performed applying different ratios between the mass of cake and the volume of the leaching agent under different durations of the process. It was concluded that at the optimal process parameters (pH 2.0–2.5; CaCl2 concentration, 3.6 mol dm-3; temperature, 95 °C; solid/liquid ratio, 1:5, the leaching efficiency of lead and silver could reach the approximate value of 94 %. Applying the same optimal process parameters, the method was applied to the leaching of a lead–silver cake in a magnesium chloride solution, but with significantly lower efficiencies. The results show that leaching of lead and silver in a calcium chloride solution could be a prospective method for increasing the recovery of lead and silver during hydrometallurgical zinc production.

Temporal stability of blood lead concentrations in adults exposed only to environmental lead

Energy Technology Data Exchange (ETDEWEB)

Delves, H T; Sherlock, J C; Quinn, M J

1984-08-01

The temporal stability of blood lead concentrations of 21 health adults (14 men and 7 women) exposed only to environmental lead was assessed by analysis of 253 blood specimens collected serially over periods from 7 to 11 months. The women had lower blood lead concentrations (mean 8.5, range 7.4-10.8 micrograms/100 ml) than did the men (mean 12.2, range 8.6-15.8 micrograms/100 ml). These are within the expected ranges for non-occupationally exposed persons. Blood lead concentrations in the serial specimens from both men and women changed very little over the study period, with standard deviations of less than 0.5 micrograms/100 ml for the majority of individual mean concentrations: for all except low subjects the standard deviations were less than 0.8 micrograms/100 ml. Two subjects showed significant changes in blood lead concentrations during the study. A temporary increase in oral lead intake was identified for one of these subjects. In the absence of substantial changes in lead exposure blood lead levels in adults are remarkably stable and for their environmental monitoring a single blood lead concentration is an excellent biological indicator.

Testing of massive lead containers by gamma densitometry