WorldWideScience

Sample records for latex modified concrete

  1. Latex-modified fiber-reinforced concrete bridge deck overlay : construction/interim report.

    Science.gov (United States)

    1993-06-01

    Latex-modified concrete (LMC) is Portland cement concrete (PCC) with an admixture of latex. LMC is considered to be nearly impermeable to chlorides and is extensively used to construct bridge deck overlays. Unfortunately, some of these overlays have ...

  2. Copolymer natural latex in concrete: Dynamic evaluation through energy dissipation of polymer modified concrete

    Science.gov (United States)

    Andayani, Sih Wuri; Suratman, Rochim; Imran, Iswandi; Mardiyati

    2018-05-01

    Portland cement concrete have been used in construction due to its strength and ecomical value. But it has some limitations, such low flexural strength, low tensile strength, low chemical resistant and etc. Due to its limitations in flexural and tensile strength, Portland cement concrete more susceptible by seismic force. There are some methods for improving its limitations. Polymer addition into concrete mixture could be one of solution for improving the flexural and tensile strength, in aiming to get erthquake resistant properties. Also, the eartquake resistant could be achieved by improving energy dissipation capacity. In this research, the earthquake resistant evalution was approached from dynamic evaluation through energy dissipation capacity, after polymer addition as concrete additives. The polymers were natural latex (Indonesian naural resource) grafted with styrene and methacrylate, forming copolymer - natural latex methacrylate (KOLAM) and copolymer - natural latex styrene (KOLAS). They were added into concrete mixture resulting polymer modified concrete. The composition of polymer are 1%, 5% and 10% weight/weight of cement. The higher capacity of energy dissipation will give more capability in either absorbing or dissipating energy, and it was predicted would give better earthquake resistant.. The use of KOLAM gave better performance than KOLAS in energy dissipation capacity. It gave about 46% for addition of 1% w/w compared to Portland cement concrete. But for addition 5% w/w and 10% w/w, they gave about 7% and 5% higher energy dissipation capacity. The KOLAM addition into concrete mixture would reduce the maximum impact load with maximumabout 35% impact load reducing after 1% w/w addition. The higher concentration of KOLAM in concrete mixture, lower reducing of impact load, they were about 4% and 3% for KOLAM 5% and 10%. For KOLAS addition in any compositions, there were no positive trend either in energy dissipation capacity or impact load properties

  3. Experimental investigation of the effect of latex solid/water ratio on latex modified co-matrix mechanical properties

    Directory of Open Access Journals (Sweden)

    Ahmed M. Diab

    2013-03-01

    Full Text Available Numerous researches were performed on latex modified concretes and associated properties, however; some vital factors were not given attention in previous works. This study focus on new factor which significantly affects the properties of latex modified cement paste, mortar or concrete. This factor is termed as ‘latex solid/water ratio’ which is defined herein as the ratio of weight of solid latex to weight of total water content of cement composite including the water in latex itself. The effect of this factor on some properties of cement paste, mortar and concrete were experimentally evaluated. Properties of cement paste include the produced calcium hydroxide and ettringite content during hydration process, while those of cement mortar take account of absorption and effect of temperature on compressive strength. Furthermore, the effect of this factor on the compressive and flexural strengths, modulus of elasticity, water penetration depth and drying shrinkage of concrete were explored. Based on experimental evidences, and spite of using different cement contents, sources of latex, water–cement ratios and slump values, it can be generally concluded that the latex solid/water ratio is a dominant factor affecting different properties of latex modified mortars and concrete.

  4. Nano-engineered polyurethane resin-modified concrete.

    Science.gov (United States)

    2014-04-01

    The goal of the proposed work is to investigate the application of nano-engineered polyurethane (NEPU) emulsions for latex modified : concrete (LMC). NEPU emulsions are non-toxic, environment friendly, durable over a wide temperature range, provide b...

  5. Mechanical and Permeability Characteristics of Latex-Modified Pre-Packed Pavement Repair Concrete as a Function of the Rapid-Set Binder Content

    Directory of Open Access Journals (Sweden)

    Jae-Woong Han

    2015-10-01

    Full Text Available We evaluated the strength and durability characteristics of latex-polymer-modified, pre-packed pavement repair concrete (LMPPRC with a rapid-set binder. The rapid-set binder was a mixture of rapid-set cement and silica sand, where the fluidity was controlled using a latex polymer. The resulting mix exhibited a compressive strength of ¥21 MPa and a flexural strength of ¥3.5 MPa after 4 h of curing (i.e., the traffic opening term for emergency repairs of pavement. The ratio of latex polymer to rapid-set binder material was varied through 0.40, 0.33, 0.29, and 0.25. Mechanical characterization revealed that the mechanical performance, permeability, and impact resistance increased as the ratio of latex polymer to rapid-set binder decreased. The mixture exhibited a compressive strength of ¥21 MPa after 4 h when the ratio of latex polymer to rapid-set binder material was ¤0.29. The mixture exhibited a flexural strength of ¥3.5 MPa after 4 h when the ratio of latex polymer to rapid-set binder material was ¤0.33. The permeability resistance to chloride ions satisfied 2000 C after 7 days of curing for all ratios. The ratio of latex polymer to rapid-set binder material that satisfied all conditions for emergency pavement repair was ¤0.29.

  6. Mechanical properties of polymer-modified porous concrete

    Science.gov (United States)

    Ariffin, N. F.; Jaafar, M. F. Md.; Shukor Lim, N. H. Abdul; Bhutta, M. A. R.; Hussin, M. W.

    2018-04-01

    In this research work, polymer-modified porous concretes (permeable concretes) using polymer latex and redispersible polymer powder with water-cement ratio of 30 %, polymer-cement ratios of 0 to 10 % and cement content of 300 kg/m3 are prepared. The porous concrete was tested for compressive strength, flexural strength, water permeability and void ratio. The cubes size of specimen is 100 mm ×100 mm × 100 mm and 150 mm × 150 mm × 150 mm while the beam size is 100 mm × 100 mm × 500 mm was prepared for particular tests. The tests results show that the addition of polymer as a binder to porous concrete gives an improvement on the strength properties and coefficient of water permeability of polymer-modified porous concrete. It is concluded from the test results that increase in compressive and flexural strengths and decrease in the coefficient of water permeability of the polymer-modified porous concrete are clearly observed with increasing of polymer-cement ratio.

  7. Latex improvement of recycled asphalt pavement

    Science.gov (United States)

    Drennon, C.

    1982-08-01

    The performance of a single unmodified milled recycled asphalt concrete was compared to milled asphalt concrete modified by addition of three types of rubber latex. Latex was added at 2, 3, 5, and 8 percent latex by weight of asphalt in the asphalt concrete. Lattices used were a styrene butadiene (SBR), a natural rubber (NR), an acrylonitrile butadiene (NBR), and four varieties of out of specification SBR lattices. Marshall tests, while indecisive, showed a modest improvement in properties of SBR and NR added material at 3 and 5 percent latex. Addition of NBR latex caused deterioration in Marshall stability and flow over that of control. Repeated load tests were run using the indirect tensile test, analyzed by the VESYS program, which computes life of pavements. Repeated load tests showed improvement in asphalt concrete life when 3 and 5 percent SBR was added. Improvement was also shown by the out of specification SBR.

  8. Exploring Polymer-Modified Concrete and Cementitious Coating with High-Durability for Roadside Structures in Xinjiang, China

    Directory of Open Access Journals (Sweden)

    Yinchuan Guo

    2017-01-01

    Full Text Available The concrete roadside structures in Xinjiang, China, such as roadside barriers, bridge rails, and drainage holes, are severely damaged by the coupled effect of seasonal freeze-thaw cycles and deicer salts. To solve the corrosion problems of roadside structures, polymer-modified concrete was recommended for the future construction of roadside structures and polymer-modified cementitious coating was suggested for the protection of the current corroded ones. In this study, air-entraining agent and carboxylated styrene-butadiene latex were added for concrete modification and the corresponding performance tests were conducted. In addition, the performances of six types of readily available coating materials, including the acrylic latex modified cementitious coating designed in this study, were tested in freeze-thaw condition with the presence of chloride ions. The results show that 0.013% of the air-entraining agent and 10% of the carboxylated styrene-butadiene latex were appropriate dosage rates for the modification of Portland cement concrete, in terms of the improvement of the freeze-thaw resistance, compressive strength, and chloride impermeability. For the protection of the current corroded roadside structures, the acrylic-modified cementitious coating material demonstrated a good performance and the field monitoring confirmed that the coating is suitable for the protection of the roadside structures in Xinjiang.

  9. Fresh and Hardened State of Polymer Modified Concrete and Mortars – A Review

    Directory of Open Access Journals (Sweden)

    Tukimat Nurul Nadrah Aqilah

    2017-01-01

    Full Text Available Polymer modified concrete or mortar is an alternative to the advancement of long serving civil engineering material - mortar and concrete. The excellence and promising benefits of modified composites have led to numerous progressive studies of its application. This paper presented a critical review from previous research on the polymer modified concrete and mortar. Both fresh and hardened state behaviours were reviewed as they are important for the development of excellent engineering material. Most of the applications of polymer modified concrete and mortar can be seen in diverse types of polymer such as latex, epoxy and emulsion. The utilization of each type of polymers resulted in different characteristics of composite concrete or mortar. Such applications have contributed to the improvement in terms of workability and mechanical strength, especially at higher grade of composite strength of concrete material.

  10. Effects of Reinforcing Fiber and Microsilica on the Mechanical and Chloride Ion Penetration Properties of Latex-Modified Fiber-Reinforced Rapid-Set Cement Concrete for Pavement Repair

    Directory of Open Access Journals (Sweden)

    Woong Kim

    2018-01-01

    Full Text Available This study evaluated the influence of reinforcement fiber type and microsilica content on the performance of latex-modified fiber-reinforced roller-compacted rapid-hardening cement concrete (LMFRCRSC for a concrete pavement emergency repair. Experimental variables were the microsilica substitution ratio (1, 2, 3, and 4%, and the reinforcement fiber (jute versus macrosynthetic fiber. In the tests, compressive, flexural, and splitting tensile strength; chloride ion penetration resistance; and abrasion resistance were assessed. From the compressive and flexural strength tests with microsilica substitution, the 4-hour curing strength decreased as the microsilica substitution ratio increased. From the chloride ion penetration test, as the microsilica substitution ratio increased, chloride ion penetration decreased. The abrasion resistances increased with the substitution ratio of microsilica increase. Based on these test results, microsilica at a substitution ratio of 3% or less and macrosynthetic fiber as the reinforcement improved the performance of LMFRCRSC for a concrete pavement emergency repair and satisfied all of the target strength requirements.

  11. Studies on physico-chemical and mechanical properties of the irradiated latex modified mortar

    International Nuclear Information System (INIS)

    Yassene, A.A.M.A.

    2009-01-01

    This thesis contains three chapter; chapter(I): Introduction and literature review on:- Introduction to polymer. - Mechanism of polymer-cement co-matrix formation.-Sulphate attack. - Solidification /stabilization of heavy metal in cement mortar. chapter(II): Materials and experimental techniques that include: 1- Preparation of latex polymer films from different polymer latices of styrene butadine rubber latex (SBR), poly (styrene-acrylic ester) latex (SAE) and vinylacetate /versatic -ester copolymer latex (C2A). The effect of γ-irradiation dose on the physico - chemical and mechanical properties of different latex polymer films was studied.2- Preparation of latex polymer-modified cement mortar with different ratios of cement: latex polymer and different curing method.3- Solidification /stabilization (S/S) of electroplating heavy metal precipitate in latex polymer- modified mortar with different cement /electroplating heavy metal sludge ratio. chapter(III) results and discussion

  12. Latex-modified grouts for in-situ stabilization of buried transuranic/mixed waste

    International Nuclear Information System (INIS)

    Allan, M.L.

    1996-06-01

    The Department of Applied Science at Brookhaven national Laboratory was requested to investigate latex-modified grouts for in-situ stabilization of buried TRU/mixed waste for INEL. The waste exists in shallow trenches that were backfilled with soil. The objective was to formulate latex-modified grouts for use with the jet grouting technique to enable in-situ stabilization of buried waste. The stabilized waste was either to be left in place or retrieved for further processing. Grouting prior to retrieval reduces the potential release of contaminants. Rheological properties of latex-modified grouts were investigated and compared with those of conventional neat cement grouts used for jet grouting

  13. Improving of Water Resistance of Asphalt Concrete Wearing Course Using Latex-Bitumen Binder

    Directory of Open Access Journals (Sweden)

    Siswanto Henri

    2017-01-01

    Full Text Available It is well known that presence of water in a bituminous mix is a critical factor which can lead to premature failure of flexible pavements. This requires solutions one of which is to formulate an asphalt mix that has a high resistance to moisture and one way to do this is to mix latex with the asphalt mix. The purpose of this experimental study was to investigate the effect of water on Marshall stability of asphalt concrete wearing course (ACWC made with a latex-bitumen binder. Latex-bitumen was mixed with aggregate and four levels of latex content were investigated in this study, namely, 0%, 2%, 4% and 6% respectively by weight of asphalt. Wet procces was used in the blending of mixtures. The procedure used to obtain the optimum binder contents conformed to the Marshall procedure (SNI 06-2489-1991. Six Marshall specimens at optimum binder content were prepared for each binder mix investigated. Three of six specimens from each group were tested under Marshall standards. The remaining specimens were tested by immersion in a bath at 60°C for 24 hours. The Marshall index of retained stability was used to evaluate the effect of water on the Marshall stability of ACWC. The results indicated that the addition of up to 4% latex to ACWC mix increased the retained Marshall stability, whereas the addition of latex above 4% decreased the retained stability of the mixture. The addition of 4% CRM significantly improved the retained stability of the mixture and was the best latex – ACWC mix.

  14. Self-healing of polymer modified concrete

    Directory of Open Access Journals (Sweden)

    Abd_Elmoaty M. Abd_Elmoaty

    2011-06-01

    Full Text Available Self healing phenomenon of concrete has been observed in traditional, fibrous, self compacting concrete. This phenomenon occurred mainly due to the presence of unhydrated cement particles in the presence of water. Mechanism of polymer in concrete depends on creating a layer and net of polymer around cement particles which enhances the properties of polymer modified concrete. This mechanism may affect the self healing of this type of concrete. This work aims to study the presence of the self healing phenomenon in polymer modified concrete and the related parameters. An experimental investigation on self healing of polymer modified concrete was undertaken. In this research work, effect of polymer type, polymer dose, cement content, cement type, w/cm ratio and age of damage were studied. The healing process extended up to 60 days. Ultrasonic pulse velocity measurements were used to evaluate the healing process. Results indicated that, the self healing phenomenon existed in polymer modified concrete as in traditional concrete. The increase of polymer dose increases the healing degree at the same healing time. This increase depends on polymer type. Also, the decrease of w/cm ratio reduces the self healing degree while the use of Type V Portland cement improves the self healing process compared with Type I Portland cement. Cement content has an insignificant effect on healing process for both concrete with and without polymer. In addition, the increase of damage age decreases the efficiency of self healing process.

  15. CONCRETE BASED ON MODIFIED DISPERSE CEMENT SYSTEM

    Directory of Open Access Journals (Sweden)

    D. V. Rudenko

    2016-08-01

    Full Text Available Purpose. The article considers definition of the bond types occurring in a modified cement concrete matrix, and the evaluation of the quality of these links in a non-uniform material to determine the geometrical and physical relationships between the structure and the cement matrix modifiers. Methodology. To achieve this purpose the studies covered the microstructure of dispersed modified concrete cement matrix, the structure formation mechanism of the modified cement concrete system of natural hardening; as well as identification of the methods of sound concrete strength assessment. Findings. The author proposed a model of the spatial structure of the concrete cement matrix, modified by particulate reinforcement crystal hydrates. The initial object of study is a set of volume elements (cells of the cement matrix and the system of the spatial distribution of reinforcing crystallohydrates in these volume elements. It is found that the most dangerous defects such as cracks in the concrete volume during hardening are formed as a result of internal stresses, mainly in the zone of cement matrix-filler contact or in the area bordering with the largest pores of the concrete. Originality. The result of the study is the defined mechanism of the process of formation of the initial strength and stiffness of the modified cement matrix due to the rapid growth of crystallohydrates in the space among the dispersed reinforcing modifier particles. Since the lack of space prevents from the free growth of crystals, the latter cross-penetrate, forming a dense structure, which contributes to the growth of strength. Practical value. Dispersed modifying cement matrix provides a durable concrete for special purposes with the design performance characteristics. The developed technology of dispersed cement system modification, the defined features of its structure formation mechanism and the use of congruence principle for the complex of technological impacts of physical

  16. Plant Growth and Water Purification of Porous Vegetation Concrete Formed of Blast Furnace Slag, Natural Jute Fiber and Styrene Butadiene Latex

    Directory of Open Access Journals (Sweden)

    Hwang-Hee Kim

    2016-04-01

    Full Text Available The purpose of this study is to investigate porous vegetation concrete formed using the industrial by-products blast furnace slag powder and blast furnace slag aggregates. We investigated the void ratio, compressive strength, freeze–thaw resistance, plant growth and water purification properties using concretes containing these by-products, natural jute fiber and latex. The target performance was a compressive strength of ≥12 MPa, a void ratio of ≥25% and a residual compressive strength of ≥80% following 100 freeze–thaw cycles. Using these target performance metrics and test results for plant growth and water purification, an optimal mixing ratio was identified. The study characterized the physical and mechanical properties of the optimal mix, and found that the compressive strength decreased compared with the default mix, but that the void ratio and the freeze–thaw resistance increased. When latex was used, the compressive strength, void ratio and freeze–thaw resistance all improved, satisfying the target performance metrics. Vegetation growth tests showed that plant growth was more active when the blast furnace slag aggregate was used. Furthermore, the use of latex was also found to promote vegetation growth, which is attributed to the latex forming a film coating that suppresses leaching of toxic components from the cement. Water purification tests showed no so significant differences between different mixing ratios; however, a comparison of mixes with and without vegetation indicated improved water purification in terms of the total phosphorus content when vegetation had been allowed to grow.

  17. A self-cleaning coating based on commercial grade polyacrylic latex modified by TiO2/Ag-exchanged-zeolite-A nanocomposite

    International Nuclear Information System (INIS)

    Nosrati, Rahimeh; Olad, Ali; Nofouzi, Katayoon

    2015-01-01

    Graphical abstract: - Highlights: • A novel nanocomposite coating based on polyacrylic was prepared. • Nanostructured TiO 2 /Ag-exchanged-zeolite-A composite material was prepared. • Prepared nanocomposite used as additive for modification of polyacrylic latex. • Modified coatings show self-cleaning and antibacterial properties. • Modified coatings show better stability in water in versus of unmodified polymer. - Abstract: The commercial grade polyacrylic latex was modified in order to prepare a self-cleaning coating. TiO 2 /Ag-exchanged-zeolite-A nanocomposite was prepared and used as additive in the matrix of polyacrylic latex to achieve a hydrophilic and photocatalytic coating. FTIR and UV–visible spectroscopy, X-ray diffraction patterns and FESEM were used to characterize the composition and structure of the nanocomposites and coatings. The acrylic coatings, were prepared by using of TiO 2 /Ag-exchanged-zeolite-A additive, had better UV and visible light absorption, hydrophilic, degradation of organic pollutants, stability in water and antimicrobial properties than pristine commercial grade polyacrylic latex coating. According to the results, the modified polyacrylic based coating containing 0.5 wt% of TiO 2 /Ag-exchanged-zeolite-A nanocomposite additive with TiO 2 to Ag-exchanged-zeolite-A ratio of 1:2 was the best coating considering most of useful properties such as small band gap and low water contact angle. The water contact angle for unmodified polyacrylic latex coating was 68° which was decreased to less than 10° in modified coating after 24 h LED lamp illumination

  18. Effects on the Physical and Mechanical Properties of Porous Concrete for Plant Growth of Blast Furnace Slag, Natural Jute Fiber, and Styrene Butadiene Latex Using a Dry Mixing Manufacturing Process.

    Science.gov (United States)

    Kim, Hwang-Hee; Kim, Chun-Soo; Jeon, Ji-Hong; Park, Chan-Gi

    2016-01-29

    To evaluate the effects of industrial by-products materials on the performance of porous concrete for plant growth, this study investigated the physical, strength, and freeze/thaw resistances of porous concrete for plant growth, prepared by replacing cement with blast furnace slag powder at 60% by weight, and replacing natural stone aggregates with coarse blast furnace slag aggregates at rates of 0%, 20%, 40%, 60% and 100% by weight. In addition, the effects of adding natural jute fiber and styrene butadiene ( SB) latex to these concrete mixtures were evaluated. The void ratio, compressive strength, and freeze/thaw resistance of the samples were measured. With increasing replacement rate of blast furnace aggregates, addition of latex, and mixing of natural jute fiber the void ratio of the concrete was increased. Compressive strength decreased as the replacement rate of blast-furnace slag aggregates increased. The compressive strength decreased after 100 freeze/thaw cycles, regardless of the replacement rate of blast furnace slag aggregates or of the addition of natural jute fiber and latex. The addition of natural jute fiber and latex decreased the compressive strength after 100 freeze/thaw cycles. The test results indicate that the control mixture satisfied the target compressive strength of 10 MPa and the target void ratio of 25% at replacement rates of 0% and 20% for blast furnace aggregates, and that the mixtures containing latex satisfied the criteria up to an aggregate replacement rate of 60%. However, the mixtures containing natural jute fiber did not satisfy these criteria. The relationship between void ratio and residual compressive strength after 100 freeze/thaw cycles indicates that the control mixture and the mixtures containing jute fiber at aggregate replacement rates of 20% and 40% satisfied the target void ratio of 25% and the target residual compressive strength of over 80% after 100 freeze/thaw cycles. The mixtures containing latex and aggregate

  19. Effects on the Physical and Mechanical Properties of Porous Concrete for Plant Growth of Blast Furnace Slag, Natural Jute Fiber, and Styrene Butadiene Latex Using a Dry Mixing Manufacturing Process

    Directory of Open Access Journals (Sweden)

    Hwang-Hee Kim

    2016-01-01

    Full Text Available To evaluate the effects of industrial by-products materials on the performance of porous concrete for plant growth, this study investigated the physical, strength, and freeze/thaw resistances of porous concrete for plant growth, prepared by replacing cement with blast furnace slag powder at 60% by weight, and replacing natural stone aggregates with coarse blast furnace slag aggregates at rates of 0%, 20%, 40%, 60% and 100% by weight. In addition, the effects of adding natural jute fiber and styrene butadiene (SB latex to these concrete mixtures were evaluated. The void ratio, compressive strength, and freeze/thaw resistance of the samples were measured. With increasing replacement rate of blast furnace aggregates, addition of latex, and mixing of natural jute fiber the void ratio of the concrete was increased. Compressive strength decreased as the replacement rate of blast-furnace slag aggregates increased. The compressive strength decreased after 100 freeze/thaw cycles, regardless of the replacement rate of blast furnace slag aggregates or of the addition of natural jute fiber and latex. The addition of natural jute fiber and latex decreased the compressive strength after 100 freeze/thaw cycles. The test results indicate that the control mixture satisfied the target compressive strength of 10 MPa and the target void ratio of 25% at replacement rates of 0% and 20% for blast furnace aggregates, and that the mixtures containing latex satisfied the criteria up to an aggregate replacement rate of 60%. However, the mixtures containing natural jute fiber did not satisfy these criteria. The relationship between void ratio and residual compressive strength after 100 freeze/thaw cycles indicates that the control mixture and the mixtures containing jute fiber at aggregate replacement rates of 20% and 40% satisfied the target void ratio of 25% and the target residual compressive strength of over 80% after 100 freeze/thaw cycles. The mixtures containing

  20. Solid state NMR and LVSEM studies on the hardening of latex modified tile mortar systems

    International Nuclear Information System (INIS)

    Rottstegge, J.; Arnold, M.; Herschke, L.; Glasser, G.; Wilhelm, M.; Spiess, H.W.; Hergeth, W.D.

    2005-01-01

    Construction mortars contain a broad variety of both inorganic and organic additives beside the cement powder. Here we present a study of tile mortar systems based on portland cement, quartz, methyl cellulose and different latex additives. As known, the methyl cellulose stabilizes the freshly prepared cement paste, the latex additive enhances final hydrophobicity, flexibility and adhesion. Measurements were performed by solid state nuclear magnetic resonance (NMR) and low voltage scanning electron microscopy (LVSEM) to probe the influence of the latex additives on the hydration, hardening and the final tile mortar properties. While solid state NMR enables monitoring of the bulk composition, scanning electron microscopy affords visualization of particles and textures with respect to their shape and the distribution of the different phases. Within the alkaline cement paste, the poly(vinyl acetate) (VAc)-based latex dispersions stabilized by poly(vinyl alcohol) (PVA) were found to be relatively stable against hydrolysis. The influence of the combined organic additives methyl cellulose, poly(vinyl alcohol) and latexes stabilized by poly(vinyl alcohol) on the final silicate structure of the cement hydration products is small. But even small amounts of additives result in an increased ratio of ettringite to monosulfate within the final hydrated tile mortar as monitored by 27 Al NMR. The latex was found to be adsorbed to the inorganic surfaces, acting as glue to the inorganic components. For similar latex water interfaces built up by poly(vinyl alcohol), a variation in the latex polymer composition results in modified organic textures. In addition to the networks of the inorganic cement and of the latex, there is a weak network build up by thin polymer fibers, most probably originating from poly(vinyl alcohol). Besides the weak network, polymer fibers form well-ordered textures covering inorganic crystals such as portlandite

  1. A self-cleaning coating based on commercial grade polyacrylic latex modified by TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite

    Energy Technology Data Exchange (ETDEWEB)

    Nosrati, Rahimeh, E-mail: ra.nosrati@gmail.com [Polymer Composite Research Laboratory, Department of Applied Chemistry, Faculty of Chemistry, University of Tabriz, Tabriz (Iran, Islamic Republic of); Olad, Ali, E-mail: a.olad@yahoo.com [Polymer Composite Research Laboratory, Department of Applied Chemistry, Faculty of Chemistry, University of Tabriz, Tabriz (Iran, Islamic Republic of); Nofouzi, Katayoon, E-mail: nofouzi@tabrizu.ac.ir [Faculty of Veterinary Medicine, University of Tabriz, Tabriz (Iran, Islamic Republic of)

    2015-08-15

    Graphical abstract: - Highlights: • A novel nanocomposite coating based on polyacrylic was prepared. • Nanostructured TiO{sub 2}/Ag-exchanged-zeolite-A composite material was prepared. • Prepared nanocomposite used as additive for modification of polyacrylic latex. • Modified coatings show self-cleaning and antibacterial properties. • Modified coatings show better stability in water in versus of unmodified polymer. - Abstract: The commercial grade polyacrylic latex was modified in order to prepare a self-cleaning coating. TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite was prepared and used as additive in the matrix of polyacrylic latex to achieve a hydrophilic and photocatalytic coating. FTIR and UV–visible spectroscopy, X-ray diffraction patterns and FESEM were used to characterize the composition and structure of the nanocomposites and coatings. The acrylic coatings, were prepared by using of TiO{sub 2}/Ag-exchanged-zeolite-A additive, had better UV and visible light absorption, hydrophilic, degradation of organic pollutants, stability in water and antimicrobial properties than pristine commercial grade polyacrylic latex coating. According to the results, the modified polyacrylic based coating containing 0.5 wt% of TiO{sub 2}/Ag-exchanged-zeolite-A nanocomposite additive with TiO{sub 2} to Ag-exchanged-zeolite-A ratio of 1:2 was the best coating considering most of useful properties such as small band gap and low water contact angle. The water contact angle for unmodified polyacrylic latex coating was 68° which was decreased to less than 10° in modified coating after 24 h LED lamp illumination.

  2. A self-cleaning coating based on commercial grade polyacrylic latex modified by TiO2/Ag-exchanged-zeolite-A nanocomposite

    Science.gov (United States)

    Nosrati, Rahimeh; Olad, Ali; Nofouzi, Katayoon

    2015-08-01

    The commercial grade polyacrylic latex was modified in order to prepare a self-cleaning coating. TiO2/Ag-exchanged-zeolite-A nanocomposite was prepared and used as additive in the matrix of polyacrylic latex to achieve a hydrophilic and photocatalytic coating. FTIR and UV-visible spectroscopy, X-ray diffraction patterns and FESEM were used to characterize the composition and structure of the nanocomposites and coatings. The acrylic coatings, were prepared by using of TiO2/Ag-exchanged-zeolite-A additive, had better UV and visible light absorption, hydrophilic, degradation of organic pollutants, stability in water and antimicrobial properties than pristine commercial grade polyacrylic latex coating. According to the results, the modified polyacrylic based coating containing 0.5 wt% of TiO2/Ag-exchanged-zeolite-A nanocomposite additive with TiO2 to Ag-exchanged-zeolite-A ratio of 1:2 was the best coating considering most of useful properties such as small band gap and low water contact angle. The water contact angle for unmodified polyacrylic latex coating was 68° which was decreased to less than 10° in modified coating after 24 h LED lamp illumination.

  3. RESEARCH OF THE STRESS STATE OF A MODIFIED IN-SITU CONCRETE

    Directory of Open Access Journals (Sweden)

    D. V. Rudenko

    2016-12-01

    Full Text Available Purpose. The article focuses on investigation of the stress state of a modified in-situ concrete of natural hardening. Methodology. To achieve the aim, the research of the microstructure of the modified cement matrix of concrete, as well as the mechanism of structure formation of modified concrete with natural hardening was conducted; the methods for reliable evaluation of concrete strength were defined. Findings. The development of internal stresses affects the properties of concretedifferently. With an increase in temperature-shrinkage deformations in time and, thus, with increasing structural stresses in the cement sheath around the grains of the filler two opposite processes may develop: zone of plastic flow or cracking. Originality. It was established that the structural features complex of the modified concrete when the load transfer leads to the formation of extensive zones of prefracture which is able to absorb a significant amount of elastic strain energy that provides the design deformation properties of the concrete for special purposes. Ideas about the definition of the criteria of cracking modified concrete, hardening under natural conditions had further development. Practical value. The resulting equations allow to solve the problem about the minimum level of structural stress in monolithic concrete in a saturated large placeholder, as well as to assess the influence of structural stresses on the properties of concrete. In normal concrete with a relatively thin cement sheath at temperature-shrinkage deformations, high tangential and low radial tension occur. In vivo, this stress is higher as a result of higher values of Δε(τ, which is not observed in the modified concrete. In the modified concretes only tangential stresses are the greatest danger to structures. The change of shrinkage stress with time is straightforward. The total temperature-shrinkage deformations have a sawtooth graph. For modified concrete the amplitude is 48

  4. The increase of compressive strength of natural polymer modified concrete with Moringa oleifera

    Science.gov (United States)

    Susilorini, Rr. M. I. Retno; Santosa, Budi; Rejeki, V. G. Sri; Riangsari, M. F. Devita; Hananta, Yan's. Dianaga

    2017-03-01

    Polymer modified concrete is one of some concrete technology innovations to meet the need of strong and durable concrete. Previous research found that Moringa oleifera can be applied as natural polymer modifiers into mortars. Natural polymer modified mortar using Moringa oleifera is proven to increase their compressive strength significantly. In this resesearch, Moringa oleifera seeds have been grinded and added into concrete mix for natural polymer modified concrete, based on the optimum composition of previous research. The research investigated the increase of compressive strength of polymer modified concrete with Moringa oleifera as natural polymer modifiers. There were 3 compositions of natural polymer modified concrete with Moringa oleifera referred to previous research optimum compositions. Several cylinder of 10 cm x 20 cm specimens were produced and tested for compressive strength at age 7, 14, and, 28 days. The research meets conclusions: (1) Natural polymer modified concrete with Moringa oleifera, with and without skin, has higher compressive strength compared to natural polymer modified mortar with Moringa oleifera and also control specimens; (2) Natural polymer modified concrete with Moringa oleifera without skin is achieved by specimens contains Moringa oleifera that is 0.2% of cement weight; and (3) The compressive strength increase of natural polymer modified concrete with Moringa oleifera without skin is about 168.11-221.29% compared to control specimens

  5. Exploiting epoxidized natural rubber latex (ENRL) as a starting raw material for latex-based products

    Science.gov (United States)

    Siti Nor Qamarina, M.; Fatimah Rubaizah, M. R.; Nurul Suhaira, A.; Norhanifah, M. Y.

    2017-12-01

    Epoxidized natural rubber latex (ENRL) is a chemically modified natural rubber latex produced from epoxidation process that involves usage of organic peracids. Conversion of the ENRL into dry rubber products has been known to exhibit many beneficial properties, however limited published works were found on diversifiying the ENRL latex-based products applications. In this preliminary work, different source of raw materials and neutralization systems were investigated. The objective was to explore possibilities in producing distinctive ENRL. Findings have demonstrated that different source of raw materials and neutralization systems influenced the typical ENRL specifications, stability behavior and particle size distribution. Morphological observations performed on these ENRL systems appeared to agree with the ENRL characteristics achieved. Since experimenting these two main factors resulted in encouraging ENRL findings, detailed work shall be further scrutinized to search for an optimum condition in producing marketable ENRL specifically for latex-based products applications.

  6. Properties of nano-silica modified pervious concrete

    Directory of Open Access Journals (Sweden)

    Bashar S. Mohammed

    2018-06-01

    Full Text Available The aim of this study is to evaluate the effects of inclusion nano-silica (also known as nano-SiO2 on the properties of pervious concrete containing fly ash (FA as a partial replacement to cement. It has been found, for cementitious paste, that incorporating NS leads to reduce the cumulative pore volume by 13.4%. While the compressive strength of NS modified pervious concrete has been improved without adversely affecting its void ratio and permeability. The workability has been adversely affected by the inclusion of NS, which can be enhanced by incorporating the fly ash and superplasticizer. The porosity of cementitious paste has increased as the FA content is increased. These results are in good agreement with SEM results. For the pervious concrete voids ratio, permeability and infiltration rate were decreased against the increase of paste to the aggregate ratio Response surface methodology (RSM has also been used to develop a model for navigating the design space of NS modified pervious concrete. Models revealed 95% significance of confidence level with difference less than 0.2 between Pred R-Squared value of 0.9515 and Adj R-Squared. The general expression has been developed for all the responses with the different coefficients using the RSM. Keywords: Fly ash, Final setting time, Infiltration rate, Pervious concrete, Nano-silica

  7. Prediction of Concrete Mix Cost Using Modified Regression Theory ...

    African Journals Online (AJOL)

    The cost of concrete production which largely depends on the cost of the constituent materials, affects the overall cost of construction. In this paper, a model based on modified regression theory is formulated to optimise concrete mix cost (in Naira). Using the model, one can predict the cost per cubic meter of concrete if the ...

  8. HIGHLY EFFECTIVE CHEMICAL MODIFIERS FOR PRODUCTION OF CONCRETES WITH PRE-SET PROPERTIES

    Directory of Open Access Journals (Sweden)

    Tkach Evgeniya Vladimirovna

    2012-10-01

    Full Text Available The paper demonstrates the application of industrial by-products and recycled materials. Waterproofing admixtures improve the structure and the properties of the cement stone. Development and preparation of highly effective waterproofing modifiers of durable effect, as well as development of the process procedure parameters, including mixing, activation, heat treatment, etc. are to be implemented. The composition of waterproofing modifiers is to be fine-tuned to synergize the behaviour of various ingredients of cement systems to assure the substantial improvement of their strength, freeze- and corrosion resistance. Multi-functional waterproofing admixtures were used to produce highly effective modified concretes. The key idea of the new method of modifying cement-based building materials is that the waterproofing admixture concentration is to exceed 10% of the weight of the binding agent within the per-unit weight of the cement stone, given that its strength does not deteriorate. GKM-type modifier coupled with organo-mineral waterproofing admixture concentration agent GT-M may be recommended for mass use in the manufacturing of hydraulic concrete and reinforced concrete products. Overview of their practical implementation has proven that waterproofing modifier GKM-S, if coupled with waterproofing admixture concentration agent GT-M, improves the corrosion control inside the cement stone and makes it possible to manufacture durable concrete and reinforced concrete products that demonstrate pre-set physical and processing behaviour. Comprehensive concrete modification by modifier GKM-S and waterproofing admixture concentration agent GT-M may be regarded as one of the most ambitious methods of production of highly effective waterproof concretes.

  9. Aspects of Degradability and Aging of Natural Rubber Latex Films Obtained by Induced Ionizing Radiation Processes of Latex Vulcanization

    International Nuclear Information System (INIS)

    Parra, D. F.

    2006-01-01

    This study refers to the degradability of NRLF, natural rubber latex films, obtained by ionizing radiation. Three types of NRLF were prepared: irradiated latex, irradiated latex with about 1% of soy lecithin and sulfur-vulcanized latex, by cold vulcanization process. The films were buried in vases of two different kinds of soil: common soil and common soil with earthworm humus. Fast aging tests in laboratory with exposition to ultraviolet rays were done in irradiated latex films and irradiated latex films with soy lecithin. The results obtained after ten months of tests with buried films agree with the results of the fast aging tests, showing singularities of each type of soil and each kind of latex process. It also shows how weather inclemency can induce the films degradation process. The sulfur-vulcanized films were weakly degraded when buried. The films with lecithin and buried in vase with only common soil showed the biggest mass loss, but the films with lecithin buried in vases with common earthworm humus and soil increased their weigh and dimensions due to fungi formation. The irradiated latex films are more degradable then the sulfur-vulcanized films. The irradiated latex film, unlike the sulfur vulcanized film, showed high fungi colonization when buried. We conclude that the irradiated latex films are more easily biodegradable than the sulfur vulcanized latex films. The biodegradability increases with the addition of small amounts of soy lecithin (∼1%). The mechanical resistance of the buried films decreased related to the non-buried ones, proving that the outdoor aging in soil and the presence of fungi in the films can modify the mechanical properties of the irradiated latex owing to the biodegradation

  10. Compatibility of repair concretes in the aggressive environment of the South of Iran

    International Nuclear Information System (INIS)

    Parhizkar, T.; Ramezaniapour, A.A.; Hillemeier, B.; Ghasemi, A.M.R.; Mozafari, N.

    2006-01-01

    Deterioration of reinforced concrete structures, namely due to corrosion of reinforcement, in the south of Iran, on the coasts of the Gulf region has become a major problem in recent years. The high cost involved in repairing and strengthening of deteriorated concrete structures in this region makes it essential that the repair materials used are compatible enough to match the residual service life of the structure. This paper presents the engineering and compatibility-related properties of two repair concretes containing silica fume and styrene butadiene rubber latex (SBR) under simulated hot and humid conditions similar to the aggressive environment of the south of Iran. A normal cement-based repair concrete was used as control. Mechanical properties were assessed and the dimension stability of the repair concrete was also evaluated. The results of this investigation show that the concrete containing silica fume and the polymer-modified concrete are appropriate materials for repair in the severe environmental conditions of the Gulf region. (author)

  11. Using locally available fly ash for modifying concrete properties

    International Nuclear Information System (INIS)

    Rizwan, S.A.; Toor, S.R.; Ahmad, H.

    2005-01-01

    This paper suggests the possible use of fly ash, a bye-product produced in our thermal power plants operating on coal as fuel for improvement of concrete quality. In the present investigation, locally available finely divided fly ash has been used for modification Presently, it is being used extensively in concrete in modem countries and is considered as waste material in general. Behavior of fly ash modified concrete in comparison to normal concrete having same mix proportions, aggregates, net water-cement ratio and similar curing conditions has been studied in short terms up to the age of 56 days during which the specimens were subjected to normal water curing method. Tests were carried out for compressive strength at 3, 7, 14,28 and 56 days, 24 hours % age water absorption at the age of 56 days and durability (resistance of concrete against N/2 solutions of both nitric acid and hydrochloric acid for one month) of concrete were also carried out at the age of 56 days. It was seen that the compressive strength of concrete modified with the available type of fly ash was less than the normal concrete. But so. far as the durability and % age water absorption are concerned, fly ash plays an important role here. 24 hours % age water absorption decreases with increase in fly ash content an admixture and as a cement replacement in concrete. But so far as durability is concerned, 20% replacement of fly ash with cement appears to be more effective than it is with 40%. The purpose of investigation was to introduce the use of fly ash in concretes to the Engineers and Architects in Pakistan. (author)

  12. THE FATIGUE DURABILITY OF THE MODIFIED ASPHALT CONCRETE UNDER THE EFFECT OF INTENSIVE TRAFFIC LOADS

    Directory of Open Access Journals (Sweden)

    Yuri KALGIN

    2016-06-01

    Full Text Available The problem of prediction of the service life of asphalt concrete surface constructed with modified asphalt concrete application onto a traffic lane is examined. Asphalt concrete behaviour in road surface under the traffic loads was analysed. There were shown The results of experiments and their mathematical analysis of the assessment of standard and modified cold asphalt concrete fatigue life on road surface were shown. The service life of an asphalt concrete surface covered with standard and modified cold asphalt concrete is examined. The prediction has been received with an account of stress relaxation processes in asphalt concrete pavement and unevenness of traffic load application.

  13. Carbon Dioxide Emission Evaluation of Porous Vegetation Concrete Blocks for Ecological Restoration Projects

    Directory of Open Access Journals (Sweden)

    Hwang-Hee Kim

    2017-02-01

    Full Text Available The purpose of this study is to determine the mix proportions that can minimize CO2 emissions while satisfying the target performance of porous vegetation concrete. The target performance of porous vegetation concrete was selected as compressive strength (>15 MPa and void ratio (>25%. This study considered the use of reinforcing fiber and styrene butadiene (SB latex to improve the strength of porous vegetation concrete, as well as the use of blast furnace slag aggregate to improve the CO2 emissions-reducing effect, and analyzed and evaluated the influence of fiber reinforcing, SB latex, and blast furnace slag aggregate on the compressive strength and CO2 emissions of porous vegetation concrete. The CO2 emissions of the raw materials were highest for cement, followed by aggregate, SB latex, and fiber. Blast furnace slag aggregate showed a 30% or more CO2 emissions-reducing effect versus crushed aggregate, and blast furnace slag cement showed a 78% CO2 emissions-reducing effect versus Portland cement. The CO2 emissions analyses for each raw material showed that the CO2 emissions during transportation were highest for the aggregate. Regarding CO2 emissions in each production stage, the materials stage produced the highest CO2 emissions, while the proportion of CO2 emissions in the transportation stage for each raw material, excluding fiber, were below 3% of total emissions. Use of blast furnace slag aggregate in porous vegetation concrete produced CO2 emissions-reducing effects, but decreased its compressive strength. Use of latex in porous vegetation concrete improved its compressive strength, but also increased CO2 emissions. Thus, it is appropriate to use latex in porous vegetation concrete to improve its strength and void ratio, and to use a blast furnace slag aggregate replacement ratio of 40% or less.

  14. Influence of Aggregate Coated with Modified Sulfur on the Properties of Cement Concrete

    Directory of Open Access Journals (Sweden)

    Swoo-Heon Lee

    2014-06-01

    Full Text Available This paper proposes the mixing design of concrete having modified sulfur-coated aggregate (MSCA to enhance the durability of Portland cement concrete. The mechanical properties and durability of the proposed MSCA concrete were evaluated experimentally. Melting-modified sulfur was mixed with aggregate in order to coat the aggregate surface at a speed of 20 rpm for 120 s. The MSCA with modified sulfur corresponding to 5% of the cement weight did not significantly affect the flexural strength in a prism concrete beam specimen, regardless of the water-cement ratio (W/C. However, a dosage of more than 7.5% decreased the flexural strength. On the other hand, the MSCA considerably improved the resistance to the sulfuric acid and the freezing-thawing, regardless of the sulfur dosage in the MSCA. The coating modified sulfur of 5% dosage consequently led to good results for the mechanical properties and durability of MSCA concrete.

  15. Application of natural seaweed modified mortar for sustainable concrete production

    Science.gov (United States)

    Siddique, M. N. I.; Zularisam, A. W.

    2018-04-01

    The effect of seaweed such as Eucheuma Cottonii (gel) and Gracilaria Sp. modified mortar on the properties of sustainable concrete was investigated. Pre-experiment and main-experiment was conducted to carry out this study. Pre-experiment was conducted to study the compressive strength of the sustainable concrete. The main-experiment studied the compressive and splitting strength. Results showed that seaweed modified mortar yielded satisfactory compressive and splitting strength of 30 MPa and 5 MPa at 28 days.

  16. Development of polymer concrete for dike insulation at LNG facilities: Phase 4, Low cost materials

    Energy Technology Data Exchange (ETDEWEB)

    Kukacka, L.E.

    1991-01-01

    Earlier GRI-sponsored work at Brookhaven National Laboratory has resulted in the development and utilization of insulating polymer concrete composites (IPC) as a means of reducing the evaporation rate of liquified natural gas in the event of a spill into a containment dike, thereby improving the safety at these sites. Although all of the required properties can be attained with the IPC, it was estimated that a low-cost replacement for the expensive organic binder would be necessary before use of the material would be cost-effective. In the current program, several latex modified cement formulations were evaluated and the most promising one identified. A mixture of two carboxylated styrene-butadiene latexes was selected for use in detailed laboratory property characterizations and a subsequent field evaluation. When compared to the properties of IPC, the latex-modified insulating materials display somewhat higher thermal conductivities, greater permeability to water, and reduced strength. However, these properties still meet most of the performance criteria, and the unit cost of the material is less than one-fifth that of IPC made with epoxy binders. When installed as a 0.75-in. thick overlay, material costs are estimated to be $1.00/ft{sup 2}.

  17. Micromechanical analysis of polyacrylamide-modified concrete for improving strengths

    Energy Technology Data Exchange (ETDEWEB)

    Sun Zengzhi [School of Materials Science and Engineering, Chang' an University, Xi' an 710064 (China)], E-mail: zz-sun@126.com; Xu Qinwu [Pavement research, Transtec Group Inc., Austin 78731 (United States)], E-mail: qinwu_xu@yahoo.com

    2008-08-25

    This paper studies how polyacrylamide (PAM) alters the physicochemical and mechanical properties of concrete. The microstructure of PAM-modified concrete and the physicochemical reaction between PAM and concrete were studied through scanning electron microscope (SEM), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), and infrared spectrum analysis. Meanwhile, the workability and strengths of cement paste and concrete were tested. PAM's modification mechanism was also discussed. Results indicate that PAM reacts with the Ca{sup 2+} and Al{sup 3+} cations produced by concrete hydration to form the ionic compounds and reduce the crystallization of Ca(OH){sub 2}, acting as a flexible filler and reinforcement in the porosity of concrete and, therefore, improving concrete's engineering properties. PAM also significantly alters the microstructure at the aggregate-cement interfacial transition zone. Mechanical testing results indicate that the fluidity of cement paste decreases initially, then increases, and decreases again with increasing PAM content. PAM can effectively improve the flexural strength, bonding strength, dynamic impact resistance, and fatigue life of concrete, though it reduces the compressive strength to some extent.

  18. Micromechanical analysis of polyacrylamide-modified concrete for improving strengths

    International Nuclear Information System (INIS)

    Sun Zengzhi; Xu Qinwu

    2008-01-01

    This paper studies how polyacrylamide (PAM) alters the physicochemical and mechanical properties of concrete. The microstructure of PAM-modified concrete and the physicochemical reaction between PAM and concrete were studied through scanning electron microscope (SEM), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), and infrared spectrum analysis. Meanwhile, the workability and strengths of cement paste and concrete were tested. PAM's modification mechanism was also discussed. Results indicate that PAM reacts with the Ca 2+ and Al 3+ cations produced by concrete hydration to form the ionic compounds and reduce the crystallization of Ca(OH) 2 , acting as a flexible filler and reinforcement in the porosity of concrete and, therefore, improving concrete's engineering properties. PAM also significantly alters the microstructure at the aggregate-cement interfacial transition zone. Mechanical testing results indicate that the fluidity of cement paste decreases initially, then increases, and decreases again with increasing PAM content. PAM can effectively improve the flexural strength, bonding strength, dynamic impact resistance, and fatigue life of concrete, though it reduces the compressive strength to some extent

  19. Rubber/clay nanocomposites by combined latex compounding and melt mixing: A masterbatch process

    International Nuclear Information System (INIS)

    Tan, Jinghua; Wang, Xiaoping; Luo, Yuanfang; Jia, Demin

    2012-01-01

    Highlights: → Rubber/Ca-montmorillonite nanocomposites were prepared by the masterbatch process. → Latex compounding method is efficient to improve the Ca-montmorillonite dispersion. → Exfoliated structure was obtained in the masterbatch by latex compounding method. → Intercalated and exfoliated structures were achieved in the vulcanizate. → The properties of vulcanizate are improved by the addition of Ca-montmorillonite. -- Abstract: Rubber/Ca-montmorillonite (Ca-MMT) nanocomposites with well exfoliated Ca-MMT layers were prepared by combination of latex compounding and melt mixing. Firstly, a high Ca-MMT content masterbatch was co-coagulated by natural rubber (NR) latex and modified Ca-MMT aqueous suspension through latex compounding. The masterbatch was added in the system of styrene butadiene rubber (SBR) and epoxidized natural rubber (ENR) by melt mixing subsequently. The X-ray diffraction (XRD) and transmission electronic microscopy (TEM) results showed that intercalated and exfoliated nanocomposites were obtained by the masterbatch technique. The effects of modified Ca-MMT introduction into the rubber matrix, via the masterbatch technique, on the properties of the resulting composites were studied. It was found that the vulcanization was hindered by the incorporation of modified Ca-MMT, while mechanical performances, thermal stability and aging resistance were improved. The increasingly glass transition temperature and the storage modulus with the loading of modified Ca-MMT were measured by dynamic mechanical analysis (DMA).

  20. Effect of Mixing Process on Polypropylene Modified Bituminous Concrete Mix Properties

    OpenAIRE

    Noor Zainab Habib; Ibrahim Kamaruddin; Madzalan Napiah; Isa Mohd Tan

    2011-01-01

    This paper presents a research conducted to investigate the effect of mixing process on polypropylene (PP) modified bitumen mixed with well graded aggregate to form modified bituminous concrete mix. Two mode of mixing, namely dry and wet with different concentration of polymer polypropylene was used with 80/100 pen bitumen, to evaluate the bituminous concrete mix properties. Three percentages of polymer varying from 1-3% by the weight of bitumen was used in this study. Three mixes namely cont...

  1. Mechanical Properties of Hot Mix Crumb Rubber Modified Asphalt Concrete Using Waste Tire

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Nak Seok; Lee, Woo Yeol [Kyonggi University, Suwon (Korea)

    1998-06-30

    Wheel tracking and ravelling tests were conducted on the hot mix crumb rubber modified asphalt concrete using waste tire to evaluate the mechanical properties in comparison with conventional asphalt concrete. According to the test results, the modified product was superior to the conventional one by 50% in the resistance of permanent deformation and by 15% in the resistance of durability. The experimental results should recommend that the waste tire is positively recycled for asphalt concrete. (author). 11 refs., 6 tabs., 2 figs.

  2. Influence of association of "EVA-NBR" on indirect tensile strength of modified bituminous concrete

    Science.gov (United States)

    Chinoun, M.; Soudani, K.; Haddadi, S.

    2016-04-01

    The aim of this work is to contribute to the improvement of the mechanical properties of bituminous concrete by modification of bituminous concrete. In this study, we present the results of the indirect tensile strength "ITS" of modified bituminous concrete by the combination of two modifiers, one is a plastomer EVA (Ethylene Vinyl Acetate) and the other is a industrial waste from the shoe soles grinding NBR (Nitrile Butadiene Rubber) as crumb rubber. To modify the bitumen a wet process was used. The results show that the modification of bitumen by EVA-NBR combination increases their resistance to the indirect traction "ITS" compared to the bituminous concrete control. The mixture of 5% [50% EVA+ 50% NBR] is given the best result among the other associations.

  3. Novel Polyvinyl Alcohol/Styrene Butadiene Rubber Latex/Carboxymethyl Cellulose Nanocomposites Reinforced with Modified Halloysite Nanotubes

    Directory of Open Access Journals (Sweden)

    Yanjun Tang

    2013-01-01

    Full Text Available Novel polyvinyl alcohol (PVA/styrene butadiene rubber (SBR latex/carboxymethyl cellulose (CMC/halloysite nanotubes (HNTs nanocomposites were successfully prepared through physical blending. The as-obtained PVA/SBR/CMC/HNTs nanocomposites were coated on the surface of old corrugated container (OCC-based paper in an effort to improve the mechanical properties of paper. To improve the dispersion of HNTs and enhance the compatibility between HNTs and polymer matrix, HNTs were modified with titanate coupling agent (TCA. FT-IR, together with TGA, confirmed that TCA was grafted onto the surface of HNTs successfully. XRD demonstrated that the crystal structures of HNTs remained almost unchanged. TEM showed that modified HNTs exhibited good dispersion and possessed nanotubular structures with an outer diameter of around 50 nm and an inner diameter of about 20 nm. SEM gave an indication that modified HNTs were dispersed more uniformly than unmodified HNTs within PVA/SBR/CMC matrix. Rheological measurement exhibited that surface modification process enhanced the compatibility between HNTs and polymer matrix, thus resulting in the decreased viscosity of nanocomposites. In comparison with unmodified HNTs, modified HNTs were found to contribute more to the enhancement in mechanical properties, which might be attributed to the better dispersion and compatibility of modified HNTs evidenced by TEM, SEM, and rheological measurement.

  4. A Study on the Properties and Chloride Resistance of Modified Sulfur Concrete for Nuclear Power Plant and Marine Structures

    International Nuclear Information System (INIS)

    Wang, Soon Myun; Chang, Hyun Young; Park, Heung Bae

    2015-01-01

    The mechanical, physical and chemical properties of concrete with modified sulfur have been compared and assessed against ordinary concrete. As its excellent chloride resistance and extended service life have been verified, the technology to apply modified sulfur to the construction of nuclear power plant and marine structures has been developed and secured. Recently, modified sulfur concrete has been applied for road pavement and repair works in more than 20 sites including highway and airport in Korea. Also, in the U.S., Federal Highway Administration and Virginia Department of Transportation are implementing tests to apply modified sulfur to bridge road pavement, and the modified sulfur concrete has been recognized for its good performance. Based on these cases, this study carried out tests on physical, mechanical and chemical properties of concrete after adding modified sulfur by building concrete specimens based on the concrete mix design employed to construct the Shin-Kori Units 3 and 4 containment building. Multiple tests were performed particularly for chemical resistance, a factor directly related to concrete service life. As a result, it has been verified that concrete with 5% modified sulfur content relative to cement weight has equal mechanical properties (compressive strength, tensile strength, etc.) and much better workability (slump change) and chemical resistance (resistance to chloride ion penetration, concrete carbonation) compared with ordinary concrete. Based on this, it has been concluded that an addition of modified sulfur can double the service life of concrete. In general, studies demonstrate that a significant amount of slag should be mixed into concrete to raise chemical resistance (but with decreasing mechanical properties). Considering this, this study is unparalleled

  5. A Study on the Properties and Chloride Resistance of Modified Sulfur Concrete for Nuclear Power Plant and Marine Structures

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Soon Myun; Chang, Hyun Young; Park, Heung Bae [KEPCO EnC, Seongnam (Korea, Republic of)

    2015-05-15

    The mechanical, physical and chemical properties of concrete with modified sulfur have been compared and assessed against ordinary concrete. As its excellent chloride resistance and extended service life have been verified, the technology to apply modified sulfur to the construction of nuclear power plant and marine structures has been developed and secured. Recently, modified sulfur concrete has been applied for road pavement and repair works in more than 20 sites including highway and airport in Korea. Also, in the U.S., Federal Highway Administration and Virginia Department of Transportation are implementing tests to apply modified sulfur to bridge road pavement, and the modified sulfur concrete has been recognized for its good performance. Based on these cases, this study carried out tests on physical, mechanical and chemical properties of concrete after adding modified sulfur by building concrete specimens based on the concrete mix design employed to construct the Shin-Kori Units 3 and 4 containment building. Multiple tests were performed particularly for chemical resistance, a factor directly related to concrete service life. As a result, it has been verified that concrete with 5% modified sulfur content relative to cement weight has equal mechanical properties (compressive strength, tensile strength, etc.) and much better workability (slump change) and chemical resistance (resistance to chloride ion penetration, concrete carbonation) compared with ordinary concrete. Based on this, it has been concluded that an addition of modified sulfur can double the service life of concrete. In general, studies demonstrate that a significant amount of slag should be mixed into concrete to raise chemical resistance (but with decreasing mechanical properties). Considering this, this study is unparalleled.

  6. Asphalt concrete modified by rubber crumbs in transport construction.

    Science.gov (United States)

    Duhovny, G. S.; Karpenko, AV

    2018-03-01

    High-temperature and low-temperature characteristics of the rubber-bitumen binder and rubber asphalt concrete based on it are researched. The determination method of binder’s low-temperature characteristics is offered. The estimation of binder’s and pavement’s stability against technological and operational aging is evaluated. Estimation of environmental and economic aspects of using rubber crumbs is made. The possibility of using rubber crumbs as modifier of organic binder for production of asphalt concrete on its base is justified.

  7. Fatigue Behavior of Modified Asphalt Concrete Pavement

    Directory of Open Access Journals (Sweden)

    saad I. Sarsam

    2016-02-01

    Full Text Available Fatigue cracking is the most common distress in road pavement. It is mainly due to the increase in the number of load repetition of vehicles, particularly those with high axle loads, and to the environmental conditions. In this study, four-point bending beam fatigue testing has been used for control and modified mixture under various micro strain levels of (250 μƐ, 400 μƐ, and 750 μƐ and 5HZ. The main objective of the study is to provide a comparative evaluation of pavement resistance to the phenomenon of fatigue cracking between modified asphalt concrete and conventional asphalt concrete mixes (under the influence of three percentage of Silica fumes 1%, 2%, 3% by the weight of asphalt content, and (changing in the percentage of asphalt content by (0.5% ± from the optimum. The results show that when Silica fumes content was 1%, the fatigue life increases by 17%, and it increases by 46% when Silica fumes content increases to 2%, and that fatigue life increases to 34 % when Silica fumes content increases to 3% as compared with control mixture at (250 μƐ, 20°C and optimum asphalt content. From the results above, we can conclude the optimum Silica fumes content was 2%. When the asphalt content was 4.4%, the fatigue life has increased with the use of silica fumes by (50%, when asphalt content was 5.4%, the additives had led to increasing the fatigue life by (69%, as compared with the conventional asphalt concrete pavement.

  8. Fatigue Performance and Multiscale Mechanisms of Concrete Toughened by Polymers and Waste Rubber

    Directory of Open Access Journals (Sweden)

    Bo Chen

    2014-01-01

    Full Text Available For improving bending toughness and fatigue performance of brittle cement-based composites, two types of water-soluble polymers (such as dispersible latex powder and polyvinyl alcohol powder and waste tire-rubber powders are added to concrete as admixtures. Multiscale toughening mechanisms of these additions in concretes were comprehensively investigated. Four-point bending fatigue performance of four series concretes is conducted under a stress level of 0.70. The results show that the effects of dispersible latex powder on bending toughness and fatigue life of concrete are better than those of polyvinyl alcohol powder. Furthermore, the bending fatigue lives of concrete simultaneously containing polymers and waste rubber powders are larger than those of concrete with only one type of admixtures. The multiscale physics-chemical mechanisms show that high bonding effect and high elastic modulus of polymer films as well as good elastic property and crack-resistance of waste tire-rubber powders are beneficial for improving bending toughness and fatigue life of cementitious composites.

  9. Effect of irradiation on the prevulcanized latex/low nitrosamines latex blends

    Energy Technology Data Exchange (ETDEWEB)

    Ibrahim, Pairu; Zin, Wan Manshol Wan [Malaysian Nuclear Agency, 43000 kajang, Selangor (Malaysia); Daik, Rusli [Faculty of Science and Technology, Universiti Kebangsaan Malaysia,43600 bangi, Selangor (Malaysia)

    2015-09-25

    Radiation Prevulcanized Natural Rubber Latex (RVNRL) was blended with Low Nitrosamines Latex (LNL) at different composition ratio. Methyl Metachrylate (MMA) was added for grafting onto the blended latex. Blended latex was subjected to gamma irradiation at various doses up to 8kGy. The mechanical properties and FTIR analysis were investigated as a function of the blended composition and irradiation dose. It was found that blending at specific ratio and gamma irradiation at specific dose led to significant improvement on the properties of the latex. The optimum mechanical properties was attained at a total blending ratio of 70% RVNRL and 30% of LNL.

  10. Nanophase modified fly ash concrete with superior concrete properties, durability and biofouling resistance for seawater applications

    International Nuclear Information System (INIS)

    Vishwakarma, Vinita; Sudha, U.; Ramachandran, D.; George, R.P.; Kamachi Mudali, U.; Kalpana Kumari; Preetha, R.; Pillai, C.S.

    2015-01-01

    There are many concrete structures in the cooling water system of nuclear power plants that are exposed to seawater in the form of tanks, pillars and reservoirs. These structures come in contact with aggressive chlorides and acid producing microbes and deteriorate by chemical and biological factors. Recently fly ash (FA) concrete has emerged exhibiting excellent degradation resistance in seawater environments. However some disadvantages are reported like lesser early strength, higher carbonation and calcium leaching. This work attempted to modify FA concrete by adding nanoparticles of TiO 2 and CaCO 3 for increased strength and degradation resistance. Four types of concrete and mortar mix namely fly ash concrete (FA), FA with 2% TiO 2 nanoparticles (FAT), FA with 2% CaCO 3 nanoparticles and FA with 2% TiO 2 : CaCO 3 nanoparticles were cast and immersed in seawater for a year. Thermal analysis and Differential thermal analysis (TG-DTA) analysis was done before exposing in sea water to know the changes in the physical properties of the specimens at higher temperature. Strength and durability were evaluated using parameters like compressive strength, split tensile test, Rapid chloride permeability test (RCPT), carbonation test and pH degradation. Detailed biofilm characterizations were attempted using microbiological and molecular biology tools to study the antibacterial properties. Calcium leaching and sulfate attack studies were carried out by laboratory exposure studies. Using field emission scanning electron microscopy (FESEM) and X-ray diffraction technique (XRD), microstructural properties and chemical phases were identified. All the nanophase modified FA specimens showed superior properties compared to FA concrete with respect to strength, carbonation depth, calcium leaching and antibacterial activity. Results are discussed in detail in the paper. (author)

  11. Influence of surface modified basalt fiber on strength of cinder lightweight aggregate concrete

    Science.gov (United States)

    Xiao, Liguang; Li, Jiheng; Liu, Qingshun

    2017-12-01

    In order to improve the bonding and bridging effect between volcanic slag lightweight aggregate concrete cement and basalt fiber, The basalt fiber was subjected to etching and roughening treatment by NaOH solution, and the surface of the basalt fiber was treated with a mixture of sodium silicate and micro-silica powder. The influence of modified basalt fiber on the strength of volcanic slag lightweight aggregate concrete was systematically studied. The experimental results show that the modified basalt fiber volcanic slag lightweight aggregate concrete has a flexural strength increased by 47%, the compressive strength is improved by 16% and the toughness is increased by 27% compared with that of the non-fiber.

  12. Modified pavement cement concrete

    Science.gov (United States)

    Botsman, L. N.; Ageeva, M. S.; Botsman, A. N.; Shapovalov, S. M.

    2018-03-01

    The paper suggests design principles of pavement cement concrete, which covers optimization of compositions and structures at the stage of mixture components selection due to the use of plasticizing agents and air-retaining substances that increase the viability of a concrete mixture. It also demonstrates advisability of using plasticizing agents together with air-retaining substances when developing pavement concrete compositions, which provides for the improvement of physical and mechanical properties of concrete and the reduction of cement binding agent consumption thus preserving strength indicators. The paper shows dependences of the main physical-mechanical parameters of concrete on cement consumption, a type and amount of additives.

  13. Development of polymer concrete for dike insulation at LNG facilities: Phase 4, Low cost materials. Final report, September 1, 1987--April 30, 1990

    Energy Technology Data Exchange (ETDEWEB)

    Kukacka, L.E.

    1991-01-01

    Earlier GRI-sponsored work at Brookhaven National Laboratory has resulted in the development and utilization of insulating polymer concrete composites (IPC) as a means of reducing the evaporation rate of liquified natural gas in the event of a spill into a containment dike, thereby improving the safety at these sites. Although all of the required properties can be attained with the IPC, it was estimated that a low-cost replacement for the expensive organic binder would be necessary before use of the material would be cost-effective. In the current program, several latex modified cement formulations were evaluated and the most promising one identified. A mixture of two carboxylated styrene-butadiene latexes was selected for use in detailed laboratory property characterizations and a subsequent field evaluation. When compared to the properties of IPC, the latex-modified insulating materials display somewhat higher thermal conductivities, greater permeability to water, and reduced strength. However, these properties still meet most of the performance criteria, and the unit cost of the material is less than one-fifth that of IPC made with epoxy binders. When installed as a 0.75-in. thick overlay, material costs are estimated to be $1.00/ft{sup 2}.

  14. Optimization of compositions of multicomponent fine-grained fiber concretes modified at different scale levels.

    Directory of Open Access Journals (Sweden)

    NIZINA Tatyana Anatolevna,

    2017-04-01

    Full Text Available The paper deals with perspectives of modification of cement composites at different scale levels (nano-, micro-, macro-. Main types of micro- and nanomodifiers used in modern concrete technology are presented. Advantages of fullerene particles applied in nanomodification of cement concretes have been shown. Use of complex modifiers based on dispersed fibers, mineral additives and nanoparticles is proposed. These are the basic components of the fiber fine-grained concretes: cement of class CEM I 42,5R produced by JSC «Mordovcement», river sand of Novostepanovskogo quarry (Smolny settlement, Ichalkovsky district, Republic of Mordovia, densified condensed microsilica (DCM-85 produced by JSC «Kuznetskie Ferrosplavy» (Novokuznetsk, highly active metakaolin white produced by LLC «D-Meta» (Dneprodzerzhinsk, waterproofing additive in concrete mix «Penetron Admix» produced by LLC «Waterproofing materials plant «Penetron» (Ekaterinburg, polycarboxylate superplasticizer Melflux 1641 F (Construction Polymers BASF, Germany. Dispersed reinforcement of concretes was provided by injection of the fibers of three types: polypropylene multifilament fiber with cutting length of 12 mm, polyacrylonitrile synthetic fiber FibARM Fiber WВ with cutting length of 12 mm and basalt microfiber «Astroflex-MBM» modified by astralene with length about 100÷500 microns. Analysis of results of the study focused on saturated D-optimal plan was carried out by polynomial models «mixture I, mixture II, technology – properties» that considers the impact of six variable factors. Optimum fields of variation of fine-grained modified fiber concrete components have been identified by the method of experimental-statistical modeling. Polygons of distribution levels of factors of modified cement fiber concretes are constructed, that allowed tracing changes in fields of tensile in compressive strength and tensile strength in bending at age of 28 days depending on target

  15. Latex allergy in health care

    Directory of Open Access Journals (Sweden)

    Tina Virtič

    2012-11-01

    Full Text Available The increasing use of natural rubber latex medical gloves in the last three decades has caused an increase in latex allergy. The majority of risk groups for allergy development include health care workers, workers in the rubber industry, atopic individuals and children with congenital malformations. Three types of pathological reactions can occur in people using latex medical gloves: irritant contact dermatitis, allergic contact dermatitis and immediate hypersensitivity. The latex allergy is caused by constituent components of latex gloves and added powders; there are also numerous latex allergens involved in cross-reactivity between latex and fruits and vegetables, the so-called latex-fruit syndrome. The diagnosis is based on an accurate history of exposure, clinical presentation and confirmatory in vivo and in vitro tests. Prevention is the easiest, most effective and least expensive way to avoid latex allergy. Powder-free latex gloves with reduced levels of proteins and chemicals, and synthetic gloves for allergic workers must be provided in the work environment. There are already many health care institutions around the world where all latex products have been replaced by synthetic material products.

  16. Determining fracture energy parameters of concrete from the modified compact tension test

    Czech Academy of Sciences Publication Activity Database

    Canteli, A.; Castañón, L.; Nieto, B.; Lozano, M.; Holušová, Táňa; Seitl, Stanislav

    2014-01-01

    Roč. 30, OCT (2014), s. 383-393 ISSN 1971-8993 R&D Projects: GA MŠk(CZ) EE2.3.20.0214 Grant - others:interní podpora AV ČR(CZ) M100411204 Institutional support: RVO:68081723 Keywords : Concrete fracture energy * Modified compact tension test * Concrete * Numerical simulation Subject RIV: JL - Materials Fatigue, Friction Mechanics

  17. Modified composite material developed on the basis of no-fines asphalt concrete

    Directory of Open Access Journals (Sweden)

    Mikhasek Andrey

    2017-01-01

    Full Text Available Being a composite material, asphalt concrete is widely used in hydraulic engineering and road construction. The paper proves one of asphalt concrete modification, which includes first creating a skeleton of no-fines concrete and then its washing-down with bituminous materials by a hot procedure, can be successfully used in hydraulic structures Modified composite material based on no-fines asphalt concrete has a harder skeleton because of links from cement stone and has a technological advantage, as through the proposed technology it allows to reduce the cost of filling porous spaces. This technology allows to conclude that concrete aggregate with size fractions of 120 mm or less and frost resistance of 50 cycles and less can be recommended for fastening of slopes.

  18. Improvement of reinforced concrete properties based on modified starch/polybutadiene nanocomposites.

    Science.gov (United States)

    Saboktakin, Amin; Saboktakin, Mohammad Reza

    2014-09-01

    A novel polymer-modified cement concrete with carboxymethyl starch (CMS) and 1,4-cis polybutadiene (PBD) system by mixing polymer dispersions or redispersible polymer powders with the fresh mixture have been examined. In this paper, the addition of CMS-PBD powders in an aqueous solution is studied. Polymeric molecules are supplied on a molecular scale, improving the approach of the relatively large cement grains by the polymers. The chemical and mechanical properties of CMS-PBD-modified cement concrete have been studied. The additions of very small amounts of CMS-PBD polymeric system results in an improvement of the durability and the adhesion strength of the cementitious materials, which makes them appropriate as repair materials. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Study of radon transport through concrete modified with silica fume

    International Nuclear Information System (INIS)

    Chauhan, R.P.; Kumar, Amit

    2013-01-01

    The concentration of radon in soil usually varies between a few kBq/m 3 and tens or hundreds of kBq/m 3 depending upon the geographical region. This causes the transport of radon from the soil to indoor environments by diffusion and advection through the pore space of concrete. To reduce indoor radon levels, the use of concrete with low porosity and a low radon diffusion coefficient is recommended. A method of reducing the radon diffusion coefficient through concrete and hence the indoor radon concentration by using silica fume to replace an optimum level of cement was studied. The diffusion coefficient of the concrete was reduced from (1.63 ± 0.3) × 10 −7 to (0.65 ± 0.01) × 10 −8 m 2 /s using 30% substitution of cement with silica fume. The compressive strength of the concrete increased as the silica-fume content increased, while radon exhalation rate and porosity of the concrete decreased. This study suggests a cost-effective method of reducing indoor radon levels. -- Highlights: • Radon diffusion study through silica fume modified concrete was carried out. • Radon diffusion coefficient of concrete decreased with increase of silica fume contents. • Compressive strength increased with increase of silica fume. • Radon exhalation rates and porosity of samples decreased with addition of silica fume. • Radon diffusion coefficient decreased to 2.6% by 30% silica fume substitution

  20. Binding kinetics of magnetic nanoparticles on latex beads and yeast cells studied by magnetorelaxometry

    International Nuclear Information System (INIS)

    Eberbeck, Dietmar; Bergemann, Christian; Hartwig, Stefan; Steinhoff, Uwe; Trahms, Lutz

    2005-01-01

    The ion exchange mediated binding of magnetic nanoparticles (MNP) to modified latex spheres and yeast cells was quantified using magnetorelaxometry. By fitting subsequently recorded relaxation curves, the kinetics of the binding reactions was extracted. The signal of MNP with weak ion exchanger groups bound to latex and yeast cells scales linearly with the concentration of latex beads or yeast cells whereas that of MNP with strong ion exchanger groups is proportional to the square root of concentration. The binding of the latter leads to a much stronger aggregation of yeast cells than the former MNP

  1. Application of recombinant latex allergens in diagnostics of occupational latex allergy

    Directory of Open Access Journals (Sweden)

    Ewa Nowakowska-Świrta

    2015-02-01

    Full Text Available Over many years, allergy to natural rubber latex has been a major problem among health care workers (HCW. The diagnosis of occupational allergy requires methods of high diagnostic accuracy in view of certification implications (e.g., a sick worker quits a job. With the development of molecular methods, the frequency of application of recombinant allergens in the diagnostics of allergic diseases continues to increase. This paper reviews the applicability of laboratory tests which use recombinant allergens in the diagnostics of occupational allergy. The diagnosis of latex allergy is based on the presence of clinical symptoms linked with exposure to latex allergens, positive skin prick tests and detection of specific IgE antibodies to latex in serum. Moreover, in some cases specific challenge tests are conducted. The analysis of literature indicates that applying the panel of recombinant latex allergens in diagnostic tests, cross-reactivity can very likely be excluded and/or sensitization can be confirmed without the need for specific challenge tests, which in case of latex allergens carries a potential risk of generalized reactions. Med Pr 2015;66(1:85–97

  2. Tensile strength of structural concrete repaired with hi-bond polymer modified mortar

    International Nuclear Information System (INIS)

    Khaskheli, G.B.

    2009-01-01

    Repair of cracks in concrete is often required to save the concrete structures. Appearance of crack in concrete is bound with the tensile strength of concrete. Recently a cement factory in Sindh has launched a HBPMM (Hi-Bond Polymer Modified Mortar) that can be used as a concrete repairing material instead of normal OPC (Ordinary Portland Cement). It is needed to investigate its performance compared to that of OPC. In total 144 concrete cylinders (150x300mm) having strength of 3000 and 5000 psi were manufactured. These cylinders were then splitted by using a UTM (Universal Testing Machine) and their actual tensile strength was obtained. The concrete cylinders were then repaired with different applications of HBPMM and arc. The repaired samples were again splitted at different curing ages (3, 7 and 28 days) and their tensile strength after repair was obtained. The results show that the concrete cylinders repaired with HBPMM could give better tensile strength than that repaired with arc, the tensile strength of concrete cylinders after repair could increase with increase in the application of repairing material i.e. HBPMM or OPC and with curing time, and HBPMM could remain more effective in case of rich mix concrete than that of normal mix concrete. (author)

  3. Latex in the Hospital Environment

    Science.gov (United States)

    LATEX in the Hospital Environment Updated Fall 2015 This list provides a guide to some of the most common objects containing latex and offers some ... remover–Sepha Pharm) 1 LATEX in the Hospital Environment (continued) Frequently contains LATEX OR/Infection Control masks, ...

  4. Practical Latex

    CERN Document Server

    Grätzer, George

    2014-01-01

    Accessible at 200+ pages to all who want to learn the practical usages of LaTeX Avoids technical subjects like font usage Friendly and easy to read, with many examples included Extra source materials include sample LaTeX files and suggestions for further reading

  5. Safety Evaluation Test on Human for Radiation Pre vulcanised Natural Rubber Latex (RVNRL)

    International Nuclear Information System (INIS)

    Pairu Ibrahim; Wan Manshol Wan Zain; Chai, Chee Keong; Sofian Ibrahim; Saadiah Sulaiman; Sharifah Ismail

    2010-01-01

    This paper discussed about clinical test conducted to determine safety evaluations on human for latex examination gloves and latex films made from Radiation Vulcanized Natural Rubber Latex (RVNRL). Two types of test were being adopted which are i) Modified Draize-95 test and ii) Patch Test on Sensitized Individuals. Modified Draize-95 test was conducted on 200 non-sensitized human subjects and Patch Test on Sensitized Individuals was conducted on 25 individuals who are allergic to the defined major chemical sensitizer presents in natural rubber product. It was found that Modified Draize-95 test has prove that there is no clinical evidence on the presence of residual chemical additives at the level that may induce Type IV allergy in the un sensitized general user population in the RVNRL gloves. Meanwhile Patch Test on Sensitized Individuals has proved that the patch test conducted using the test article on 25 individuals who are allergic to the defined major chemical sensitizers present in natural rubber products, thiuram, carbamates or thiazoles produced a negative response, meeting the pre requirement for the claim of reduced reaction-inducing potential. (author)

  6. Latex allergy in the workplace.

    Science.gov (United States)

    Toraason, M; Sussman, G; Biagini, R; Meade, J; Beezhold, D; Germolec, D

    2000-11-01

    While less than 1% of the general population is sensitized to latex, the U.S. Occupational Safety and Health Administration estimates that 8-12% of health-care workers are sensitized. The major source of workplace exposure is powdered natural rubber latex (NRL) gloves. NRL is harvested from HEVEA: brasiliensis trees and ammoniated to prevent coagulation resulting in the hydrolysis of the latex proteins. Prior to use in manufacturing, the latex is formulated by the addition of multiple chemicals. Thus, human exposure is to a mixture of residual chemicals and hydrolyzed latex peptides. Clinical manifestations include irritant contact dermatitis, allergic contact dermatitis (type IV), and type I immediate hypersensitivity response. Type I (IgE-mediated) NRL allergy includes contact urticaria, systemic urticaria, angioedema, rhinitis, conjunctivitis, bronchospasm, and anaphylaxis. Taking an accurate history, including questions on atopic status, food allergy, and possible reactions to latex devices makes diagnosis of type-I latex allergy possible. To confirm a diagnosis, either in vivo skin prick testing (SPT) or in vitro assays for latex-specific IgE are performed. While the SPT is regarded as a primary confirmatory test for IgE-mediated disease, the absence of a U.S. Food and Drug Administration-licensed HEVEA: brasiliensis latex extract has restricted its use in diagnosis. Serological tests have, therefore, become critically important as alternative diagnostic tests. Three manufacturers currently have FDA clearance for in vitro tests, to detect NRL-specific IgE. The commercially available assays may disagree on the antibody status of an individual serum, which may be due to the assay's detecting anti-NRL IgEs to different allergenic NRL proteins. Sensitized individuals produce specific IgE antibody to at least 10 potent HEVEA: allergens, Hev b 1-Hev b 10, each of which differs in its structure, size, and net charge. The relative content and ratios of Hevs in the

  7. [Prevention of adverse effects in latex allergic patients: organizing a latex safe operating theatre].

    Science.gov (United States)

    Bonalumi, Sabrina; Barbonaglia, Patrizia; Bertocchi, Carmen

    2006-01-01

    In 2001 the General Health Direction of Region Lombardia approved (decree n. 22303) a guideline for the prevention of latex allergic reactions in patients and health care workers. This document provides general recommendations in order to standardize behaviors in regional health care facilities. The reason is due to a rise in the incident of reactions to latex products in the last 20 years. Nowadays the prevalence is higher in certain risk groups (subjected to frequent and repeated exposures) rather than the general population. The aim of the project was to organize a latex safe operating theatre in the Ospedale Maggiore Policlinico, Mangiagalli e Regina Elena of Milan (Fondazione) and to standardize behaviors in order to prevent adverse effects in latex allergic patients. Thanks to the literature review and the creation of a multidisciplinar team, we produced a protocol. Therefore, we requested manufacturers the certification of the latex content of their products. Results and conclusion. When latex allergic patients need to undergone surgery in our hospital, a latex safe operating theatre is organized by personnel following a multidisciplinar protocol. No allergic reactions were experienced during surgical procedures after the creation of an environment as free as possible from latex contamination. The project will involve an emergency room, one room or more of a ward and of the outpatients department.

  8. Prediction of the Chloride Resistance of Concrete Modified with High Calcium Fly Ash Using Machine Learning.

    Science.gov (United States)

    Marks, Michał; Glinicki, Michał A; Gibas, Karolina

    2015-12-11

    The aim of the study was to generate rules for the prediction of the chloride resistance of concrete modified with high calcium fly ash using machine learning methods. The rapid chloride permeability test, according to the Nordtest Method Build 492, was used for determining the chloride ions' penetration in concrete containing high calcium fly ash (HCFA) for partial replacement of Portland cement. The results of the performed tests were used as the training set to generate rules describing the relation between material composition and the chloride resistance. Multiple methods for rule generation were applied and compared. The rules generated by algorithm J48 from the Weka workbench provided the means for adequate classification of plain concretes and concretes modified with high calcium fly ash as materials of good, acceptable or unacceptable resistance to chloride penetration.

  9. Transcript Profiling of Hevea brasiliensis during Latex Flow

    Directory of Open Access Journals (Sweden)

    Jinquan Chao

    2017-11-01

    Full Text Available Latex exploitation enhances latex regeneration in rubber trees. The latex exploitation-caused latex flow lasts from 10 min to a few hours, which is convenient for exploring the transcript profiling of latex metabolism-related genes at the different stages of latex flow. In the present study, the expression pattern of 62 latex metabolism-related genes involved in water transportation, carbohydrate metabolism, natural rubber biosynthesis, hormone signaling, ROS generation and scavenging, and latex coagulum across three stages of latex flow between rubber tree clones CATAS7-33-97 and CATAS8-79 were comparatively analyzed by quantitative real-time PCR. The two clones show differences in latex regeneration and have a different duration of latex flow. The results showed that the expression levels of 38 genes were significantly higher in CATAS8-79 latex than in CATAS7-33-97 during latex regeneration, while 45 genes had a notably higher expression level in CATAS8-79 latex during latex flow. Together with the activation of the MEP pathway and jasmonate pathway in CATAS8-79 latex, HbPIP1;3, HbPIP1;4, HbSUT3, HbSus3, HbHMGS1-2, HbMK should contribute to the high latex regeneration ability. The up-regulation of ethylene signaling and Hb44KD and the down-regulation of latex coagulation-related genes in CATAS8-79 latex might contribute to its longer latex flow duration. This study provides some cues for revealing the regulation of latex metabolism in rubber trees.

  10. Latex allergy and filaggrin null mutations

    DEFF Research Database (Denmark)

    Carlsen, Berit C; Meldgaard, Michael; Hamann, Dathan

    2011-01-01

    to aeroallergens and it is possible that filaggrin null mutations also increase the risk of latex allergy. The aim of this paper was to examine the association between filaggrin null mutations and type I latex allergy. Methods Twenty latex allergic and 24 non-latex allergic dentists and dental assistants...... in the cases in this study may not have occurred through direct skin contact but through the respiratory organs via latex proteins that are absorbed in glove powder and aerosolized...

  11. Cream concentrated latex for foam rubber products

    Science.gov (United States)

    Suksup, R.; Imkaew, C.; Smitthipong, W.

    2017-12-01

    Fresh natural latex (around 40% rubber and 60% water) can be transformed to concentrated natural latex (around 60% rubber and 40% water) in order to realise economical transportation and easier latex product’s preparation. The concentrated natural latex is an extremely valuable material. It can be applied for many types of products, for example, foam rubber as pillow and mattress, elastic band, etc. Industrially, the concentrated natural latex can be prepared by centrifugation which requires an enormous expensive machine. From the eco-friendly products point of view, most of rubber entrepreneurs in the world try to develop a green rubber product. So, the main objective of this study is to prepare the cream concentrated latex without any sophisticated machine. Thus, we work on a simple, cheap and green method that does not use any expensive machine but uses water-based chemical as sodium alginate to prepare the cream concentrated latex. The optimal amount of sodium alginate in the latex was studied. The main characteristics of the cream concentrated latex were tested by various technics, such as alkalinity, total solid content (TSC), dry rubber content (DRC), etc. We found that there are no significant differences of results between fresh natural latex and cream concentrated latex, except for the TSC and DRC. The TSC and DRC of cream latex are higher than those of fresh natural latex. Finally, we propose a model of natural rubber particle and sodium alginate to form the cream concentrated latex.

  12. Influence of Crumb-Rubber in the Mechanical Response of Modified Portland Cement Concrete

    Directory of Open Access Journals (Sweden)

    J. Retama

    2017-01-01

    Full Text Available The influence of crumb-rubber on the mechanical properties of Portland cement concrete (PCC is studied by experimental tests and numerical simulations. The main hypothesis of the study is that replacing part of the stone aggregate with crumb-rubber in the mix modifies the energy dissipation during the cracking process and affects the concrete behaviour under monotonically increasing loads. The experimental research program characterizes the mechanical properties of PCC for three different types of concrete with a variable content of crumb-rubber. The experimental results showed that fracture energy and other properties are directly related to the rubber fineness used in the mixture. The material properties derived for these laboratory tests are used to study, by numerical models, its response through its damage evolution. The numerical model used to simulate the damage evolution of the concrete is the Embedded Discontinuity Method (EDM. One characteristic of the EDM is that it does not need to modify the mesh topology to propagate the damage through the continuum solid. For this study, the Disk-Shaped Compact Tension specimen geometry, normed by the D7313-13 of the ASTM, is used. Results showed that the numerical methods provide good approximation of the experimental curve in the elastic and softening branches.

  13. Effect of copolymer latexes on physicomechanical properties of mortar containing high volume fly ash as a replacement material of cement.

    Science.gov (United States)

    Negim, El-Sayed; Kozhamzharova, Latipa; Gulzhakhan, Yeligbayeva; Khatib, Jamal; Bekbayeva, Lyazzat; Williams, Craig

    2014-01-01

    This paper investigates the physicomechanical properties of mortar containing high volume of fly ash (FA) as partial replacement of cement in presence of copolymer latexes. Portland cement (PC) was partially replaced with 0, 10, 20, 30 50, and 60% FA. Copolymer latexes were used based on 2-hydroxyethyl acrylate (2-HEA) and 2-hydroxymethylacrylate (2-HEMA). Testing included workability, setting time, absorption, chemically combined water content, compressive strength, and scanning electron microscopy (SEM). The addition of FA to mortar as replacement of PC affected the physicomechanical properties of mortar. As the content of FA in the concrete increased, the setting times (initial and final) were elongated. The results obtained at 28 days of curing indicate that the maximum properties of mortar occur at around 30% FA. Beyond 30% FA the properties of mortar reduce and at 60% FA the properties of mortar are lower than those of the reference mortar without FA. However, the addition of polymer latexes into mortar containing FA improved most of the physicomechanical properties of mortar at all curing times. Compressive strength, combined water, and workability of mortar containing FA premixed with latexes are higher than those of mortar containing FA without latexes.

  14. Modified electrical survey for effective leakage detection at concrete hydraulic facilities

    Science.gov (United States)

    Lee, Bomi; Oh, Seokhoon

    2018-02-01

    Three original electrode arrays for the effective leakage detection of concrete hydraulic facilities through electrical resistivity surveys are proposed: 'cross-potential', 'direct-potential' and modified tomography-like arrays. The main differences with respect to the commonly used arrays are that the current line-sources are separated from potential pole lines and floated upon the water. The potential pole lines are located directly next to the facility in order to obtain intuitive data and useful interpretations of the internal conditions of the hydraulic facility. This modified configuration of the array clearly displays the horizontal variation of the electrical field around the damaged zones of the concrete hydraulic facility, and any anomalous regions that might be found between potential poles placed across the facilities. In order to facilitate the interpretation of these modified electrical surveys, a new and creative way of presenting the measurements is also proposed and an inversion approach is provided for the modified tomography-like array. A numerical modeling and two field tests were performed to verify these new arrays and interpretation methods. The cross and direct potential array implied an ability to detect small variations of the potential field near the measurement poles. The proposed array showed the overall potential distribution across the hydraulic facility which may be used to assist in the search of trouble zones within the structure, in combination with the traditional electrical resistivity array.

  15. Anti-ulcer activity of Synadenium grantii latex

    Directory of Open Access Journals (Sweden)

    Larissa L. G. Costa

    2012-10-01

    Full Text Available Synadenium grantii Hook f., Euphorbiaceae, is popularly known as leitosinha or janaúba. The diluted latex (18 drops/L of water is commonly used in the south of Brazil to treat gastric disturbances. This study evaluated phytochemical screening and toxicity using Artemia salina Leach of crude bark extract and also latex. The toxicity and the anti-ulcer activity of S. grantii latex were also tested in rats. Phytochemical results showed presence of tannins, terpenes, unsaponificable substances, coumarins and anthraquinones in the crude bark extract and terpenes in the latex. Gas chromatography-mass spectrometry (GC-MS analysis demonstrated the presence of diterpene tigliane esters in the latex, identified as 12-deoxyphorbol-13-(2-metilpropionate and phorbol 12,13,20-triacetate. The toxicity results using A. salina presented CL50 26.58μg/mL and CL50 778.66μg/mL, for the latex and the crude bark extract respectively. The toxicological hepatic parameters of the diluted latex were not different to the control group (p<0.05. The eosinophils cells showed an increase in both the diluted and pure latex groups. The pure latex showed gastric protection of 90% (p<0.05 and the diluted latex showed 6% compared to the negative control. Therefore, our data indicate that S. grantii latex, under research conditions presented gastric protection. Pure latex showed more toxicity than the diluted latex.

  16. Latex Allergy In Health Care Workers

    Directory of Open Access Journals (Sweden)

    Hayriye Sarıcaoğlu

    2013-05-01

    Full Text Available Background and Design: We aimed to determine the frequency of latex allergy in our hospital and to to evaluate the clinical and demographical features of the cases.Materials and Methods: A detailed questionnaire was administered to healthcare workers by a physician. Skin prick test with latex and patch test with rubber chemicals and a piece of latex glove were performed for all healthcare workers. Latex-specific IgE was measured in serum.Results: The study sample consisted of 36 nurses, 14 doctors, and 50 healthcare workers. While 46 subjects had symptoms, 54 subjects had no symptoms. The relationship of clinical disease with working duration, exposure duration (hour/day, history of atopy, and drug/food allergies was statistically significant. Five nurses and 1 healthcare worker had positive skin prick test. Two of them had positive latex-specific IgE. Positive skin prick test statistically significantly correlated with occupation, working duration, exposure duration (hour/day and positive latex-specific IgE. Two nurses and 2 healthcare workers had positive latex-specific IgE. Two of them had positive skin prick test. Positive latexspecific IgE statistically significantly correlated with working duration, exposure duration, and positive skin prick test. Patch test with a piece of latex glove was negative in all subjects. Three healthcare workers had positive patch test with thiuram-mix, one of them had also positive patch test with mercaptobenzothiazole.Discussion: One of the risk factors for latex allergy is occupations involving frequent exposure to latex products. Latex allergy should be taken into consideration if type I hypersensitivity reactions occur in occupational groups at risk for anaphylactic reaction.

  17. Experimental data on compressive strength and durability of sulfur concrete modified by styrene and bitumen.

    Science.gov (United States)

    Dehestani, M; Teimortashlu, E; Molaei, M; Ghomian, M; Firoozi, S; Aghili, S

    2017-08-01

    In this data article experimental data on the compressive strength, and the durability of styrene and bitumen modified sulfur concrete against acidic water and ignition are presented. The percent of the sulfur cement and the gradation of the aggregates used are according to the ACI 548.2R-93 and ASTM 3515 respectively. For the styrene modified sulfur concrete different percentages of styrene are used. Also for the bitumen modified sulfur concrete, different percentages of bitumen and the emulsifying agent (triton X-100) are utilized. From each batch three 10×10×10 cm cubic samples were casted. One of the samples was used for the compressive strength on the second day of casting, and one on the twenty-eighth day. Then the two samples were put under the high pressure flame of the burning liquid gas for thirty seconds and their ignition resistances were observed. The third sample was put into the acidic water and after twenty eight days immersion in water was dried in the ambient temperature. After drying its compressive strength has been evaluated.

  18. PROSPECTS FOR APPLICATION OF COMPLEX-MODIFIED SAND ASPHALT CONCRETE IN ROAD CONSTRUCTION

    Directory of Open Access Journals (Sweden)

    D. Yu. Alexandrov

    2017-01-01

    Full Text Available The paper considers a possibility to use sand asphalt concrete as a material for protection of asphalt concrete and cement concrete road pavements against affection of external destructive factors. Advantages and disadvantages of sand asphalt concrete road pavements have been determined in the paper. The paper provides recommendations on improvement of sand asphalt concrete properties and contains an analysis of possible variants for usage of complex-modified sand asphalt concrete in the road construction. It has been noted that according to its potentially possible physical and mechanical properties activated quartz sand being micro-reinforced by dispersive industrial wastes is considered as an efficient component for creation of constructive layers in road asphalt concrete pavements. The paper reveals only specific aspects of the efficient application of quartz sand in road asphalt concrete. The subject of the paper loоks rather interesting for regions where there are no rock deposits for obtaining broken-stone ballast but there is rather significant spreading of local quarts sand. Its successful application is connected with the necessity to develop special equipment for physical and chemical activation of sand grain surface that permits strongly to increase an adhesive strength in the area of phase separation within the “bitumen–SiO2” system. The considered problem is a topical one and its solution will make it possible to local sand in a maximum way and partially to exclude application of broken stone in road construction.

  19. Vanderbilt University Gamma Irradiation of Nano-modified Concrete (2017 Milestone Report)

    Energy Technology Data Exchange (ETDEWEB)

    Deichert, Geoffrey G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Linton, Kory D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Selby, Aaron P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Reches, Yonathan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-08-01

    This document outlines the irradiation of concrete specimens in the Gamma Irradiation Facility in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL). Two gamma irradiation runs were performed in July of 2017 on 18 reference mortar bar specimens, 26 reference cement paste bar specimens, and 28 reference cement paste tab specimens to determine the dose and temperature response of the specimens in the gamma irradiation environment. Specimens from the first two gamma irradiations were surveyed and released to Vanderbilt University. The temperature and dose information obtained informs the test parameters of the final two gamma irradiations of nano-modified concrete planned for FY 2018.

  20. Latex sensitisation in healthcare workers in Singapore.

    Science.gov (United States)

    Tang, M B Y; Leow, Y H; Ng, V; Koh, D; Goh, C L

    2005-06-01

    Epidemiological data on latex sensitisation among Asian healthcare workers is lacking. The aim of the study is to determine the rate of latex sensitisation in our healthcare workers. We recruited 313 healthcare workers, of which 46.6% were operating theatre staff and 53.4% were non-operating theatre staff. Seventy-one administrative staff served as controls. All participants answered a self-administered questionnaire relating to latex exposure and glove-related symptoms. Latex sensitisation was determined by skin prick testing to latex and latex-specific IgE detection. The prevalence of latex sensitisation among healthcare workers was 9.6%, with no difference between operating theatre and nonoperating theatre staff. Glove-related symptoms were reported in 13.7% of all healthcare workers, of which 22.9% were sensitised to latex. Only 26.7% of latex-sensitised healthcare workers had glove-related symptoms while the rest were asymptomatic. The most common symptoms were itch and hand eczema but the most important discriminating symptom was contact urticaria. Personal history of atopy was more common in sensitised healthcare workers (40.0%) compared to non-sensitised workers (31.8%). Only 1 out of 9 (11.2%) symptomatic latex-sensitised subjects had sought previous medical attention for the problem. Latex sensitisation among healthcare workers in Singapore should be considered a significant occupational health risk, as it is in the West. Increased screening and awareness of this problem is essential to identify those at risk.

  1. Content of Asthmagen Natural Rubber Latex Allergens in Commercial Disposable Gloves.

    Science.gov (United States)

    Bittner, C; Garrido, M V; Krach, L H; Harth, V

    The use of natural rubber latex (NRL) gloves in many occupations may lead to latex sensitization, allergic asthma, and skin reactions. Due to their good properties and environmental safety NRL gloves are still being used in the healthcare setting, but also in the food industry, by hairdressers, cleaners, etc. The aim of our study was to assess the protein and NRL allergen content in commercial gloves by different methods, including a new assay. Twenty commercially available NRL gloves were analyzed. Protein extraction was performed according to the international standard ASTM D-5712. Total protein content was measured with a modified Lowry method, NRL content with the CAP Inhibition Assay, the Beezhold ELISA Inhibition Assay, and an innovative ELISA with IgY-antibodies extracted from eggs of NRL-immunized hens (IgY Inhibition Assay). We found a high protein content in a range of 215.0-1304.7 μg/g in 8 out of the 20 NRL gloves. Seven of the 20 gloves were powdered, four of them with a high protein content. In gloves with high protein content, the immunological tests detected congruently high levels of NRL allergen. We conclude that a high percentage of commercially available NRL gloves still represent a risk for NRL allergy, including asthma. The modified Lowry Method allows to infer on the latex allergen content.

  2. Use of micrometric latex beads to improve the porosity of hydroxyapatite obtained by chemical coprecipitation method

    Science.gov (United States)

    Webler, G. D.; Rodrigues, W. C.; Silva, A. E. S.; Silva, A. O. S.; Fonseca, E. J. S.; Degenhardt, M. F. S.; Oliveira, C. L. P.; Otubo, L.; Barros Filho, D. A.

    2018-04-01

    Hydroxyapatite is one of the most important biomaterials whose application mainly extends to implants and drug delivery. This work will discuss the changes in the pore size distribution of hydroxyapatite when there are latex beads present during the synthesis. These changes were monitored using different techniques: small angle X-ray scattering, X-ray diffraction, thermal gravimetrical analysis, N2 adsorption, scanning and transmission electron microscopy. Latex beads and hydroxyapatite form a single nanocomposite with well-distinguished inorganic and organic phases. Latex bead removal in the temperature range of 300-600 °C did not modify the original crystalline structure of hydroxyapatite. However, the latex beads favored an increase in the adsorption capacity of mesopores at temperatures higher than their glassy transition (Tg). The main result of this research work consists on the increase of surface area and pore size distribution obtained after the removal of latex beads template. Latex beads have been used in a different approach changing the porosity of hydroxyapatite scaffolds not only introducing new routes for cell integration but also broadening the pore size distribution which can result in a more high efficiency for drug release in living cells.

  3. Effect of Copolymer Latexes on Physicomechanical Properties of Mortar Containing High Volume Fly Ash as a Replacement Material of Cement

    Directory of Open Access Journals (Sweden)

    El-Sayed Negim

    2014-01-01

    Full Text Available This paper investigates the physicomechanical properties of mortar containing high volume of fly ash (FA as partial replacement of cement in presence of copolymer latexes. Portland cement (PC was partially replaced with 0, 10, 20, 30 50, and 60% FA. Copolymer latexes were used based on 2-hydroxyethyl acrylate (2-HEA and 2-hydroxymethylacrylate (2-HEMA. Testing included workability, setting time, absorption, chemically combined water content, compressive strength, and scanning electron microscopy (SEM. The addition of FA to mortar as replacement of PC affected the physicomechanical properties of mortar. As the content of FA in the concrete increased, the setting times (initial and final were elongated. The results obtained at 28 days of curing indicate that the maximum properties of mortar occur at around 30% FA. Beyond 30% FA the properties of mortar reduce and at 60% FA the properties of mortar are lower than those of the reference mortar without FA. However, the addition of polymer latexes into mortar containing FA improved most of the physicomechanical properties of mortar at all curing times. Compressive strength, combined water, and workability of mortar containing FA premixed with latexes are higher than those of mortar containing FA without latexes.

  4. Waste Tire Particles and Gamma Radiation as Modifiers of the Mechanical Properties of Concrete

    Directory of Open Access Journals (Sweden)

    Eduardo Sadot Herrera-Sosa

    2014-01-01

    Full Text Available In polymer reinforced concrete, the Young’s modulus of both polymers and cement matrix is responsible for the detrimental properties of the concrete, including compressive and tensile strength, as well as stiffness. A novel methodology for solving such problems is based on use of ionizing radiation, which has proven to be a good tool for improvement on physical and chemical properties of several materials including polymers, ceramics, and composites. In this work, particles of 0.85 mm and 2.80 mm obtained from waste tire were submitted at 250 kGy of gamma radiation in order to modify their physicochemical properties and then used as reinforcement in Portland cement concrete for improving mechanical properties. The results show diminution on mechanical properties in both kinds of concrete without (or with irradiated tire particles with respect to plain concrete. Nevertheless such diminutions (from 2 to 16% are compensated with the use of high concentration of waste tire particles (30%, which ensures that the concrete will not significantly increase the cost.

  5. Comparative study on plant latex particles and latex coagulation in Ficus benjamina, Campanula glomerata and three Euphorbia species.

    Directory of Open Access Journals (Sweden)

    Georg Bauer

    Full Text Available Among latex-producing plants, mainly the latex of Hevea brasiliensis has been studied in detail so far, while comprehensive comparative studies of latex coagulation mechanisms among the more than 20,000 latex-bearing plant species are lacking. In order to give new insights into the potential variety of coagulation mechanisms, the untreated natural latices of five latex-bearing plants from the families Euphorbiaceae, Moraceae and Campanulaceae were visualised using Cryo-SEM and their particle size compared using the laser diffraction method. Additionally, the laticifers of these plants species were examined in planta via Cryo-SEM. Similar latex particle sizes and shape were found in Ficus benjamina and Hevea brasiliensis. Hence, and due to other similarities, we hypothesize comparable, mainly chemical, coagulation mechanisms in these two species, whereas a physical coagulation mechanism is proposed for the latex of Euphorbia spp. The latter mechanism is based on the huge amount of densely packed particles that after evaporation of water build a large surface area, which accelerates the coagulation procedure.

  6. Laboratory investigation of the performances of cement and fly ash modified asphalt concrete mixtures

    Directory of Open Access Journals (Sweden)

    Suched Likitlersuang

    2016-09-01

    Full Text Available The influence of filler materials on volumetric and mechanical performances of asphalt concrete was investigated in this study. The AC60/70 asphalt binder incorporating with cement and fly ash as filler materials was mixed with limestone following the Marshall mix design method. The filler contents of cement and/or fly ash were varied. The non-filler asphalt concrete mixtures of the AC60/70 and the polymer modified asphalt were prepared for the purpose of comparison. The investigation programme includes the indirect tensile test, the resilient modulus test and the dynamic creep test. The tests are conducted under the humid temperate environments. All tests were then carried out under standard temperature (25 °C and high temperature (55 °C by using a controlled temperature chamber via the universal testing machine. The wet-conditioned samples were prepared to investigate the moisture susceptibility. Results show that cement and/or fly ash were beneficial in terms of improved strength, stiffness and stripping resistance of asphalt mixture. In addition, the combined use of cement and fly ash can enhance rutting resistance at wet and high temperature conditions. The results indicate that the strength, stiffness and moisture susceptibility performances of the asphalt concrete mixtures improved by filler are comparable to the performance of the polymer modified asphalt mixture. Keywords: Asphalt concrete, Filler, Resilient modulus, Dynamic creep test, Moisture susceptibility

  7. Fracture resistance of asphalt concrete modified with crumb rubber at low temperatures

    Directory of Open Access Journals (Sweden)

    A. Razmi

    2018-05-01

    Full Text Available The main objective of this study is to obtain fracture toughness of asphalt concrete modified by Crumb Rubber (CR and Sasobit at low temperatures. First, Bending Beam Rheometer (BBR test was performed on unmodified binder (binder 60/70, binder 60/70 + 3%Sasobit and 20%CR + 3%Sasobit modified asphalt binder to find how each modifier affect asphalt binder stiffness and relaxation rate at low temperatures. Mixed mode I/II fracture tests were conducted by cracked Semi-Circular Bending (SCB specimens and the critical stress intensity factors were calculated for pure mode I, mixed mode I/II and pure mode II conditions. Results of BBR tests indicated that 20%CR + 3%Sasobit reduces stiffness and the m-value increase at low temperatures. As a result, 20%CR + 3%Sasobit has positive effect on low temperatures performance by improving thermal cracking resistance. Also, according to the fracture toughness test results, the Warm Mix Asphalt (WMA mixture containing 20% CR, shows higher resistance against crack growth than WMA mixture. It was found that mixed mode I/II can be more detrimental than pure mode I and II conditions. Keywords: Crumb rubber, Asphalt concrete, Bending Beam Rheometer, Fracture resistance, Semi-circular bending test

  8. Determining fracture energy parameters of concrete from the modified compact tension test

    Directory of Open Access Journals (Sweden)

    A. Fernández-Canteli

    2014-10-01

    Full Text Available The modified compact tension (MCT test, though not yet recognized as a valid test for determining fracture energy of concrete, is believed to represent a plausible and suitable alternative versus other well established procedures, such as the wedge-splitting test (WST and the three point (3PB or four point bending (4PB tests, due to its simplicity and low cost. The aim of the paper is twofold: Firstly, to demonstrate the necessary correspondence between the experimental MCT test setup and finite element simulations and secondly, to initiate the way of establishing the desirable conversion between the fracture energy parameter values resulting from the MCT test and the standard conventional procedures. MCT tests are carried out and compared with the numerical results from 2-D and 3-D finite element calculations using the commercial codes ABAQUS and ATENA, the latter being specifically developed for applications on concrete structures and elements. In this way, the usability of the modified compact tension test for practical purposes is confirmed.

  9. [Latex allergy in a population at risk].

    Science.gov (United States)

    Ruiz Fernández, M; Flores Sandoval, G; Orea Solano, M

    1999-01-01

    The allergy to latex is an illness whose prevalence has been increased in very significant form in the last years. To know the allergy incidence to latex in population of risk, as well as to identify the related sintomatology and the importance or paper that play the atopia antecedents and time of contact with latex for the development of the illness. We carry out a prospective, descriptive, experimental and traverse study in population of risk, in the service of Allergy and clinical Immunology of the Hospital Regional Lic. Adolfo López Mateos, ISSSTE. One hundred patients of both sexes were included, with age of 20 to 50 years, with the antecedent of being personal medical and paramedic and to have presented contact with latex material in a minimum period of one year. They were carried out clinical history with registration of sintomatology nasal, bronchial, cutaneous and associated to contact with latex. They were carried out cutaneous test for prick to latex with positive control with the help of histamine solution and negative control with solution of Evans and immediate reading of the same one. 22% of the patients in study, they presented positive skin test latex, with a time of exhibition 10 year-old average, 68% presented antecedent of atopy personal, family and, likewise the associate sintomatology was in a 33.3% dermatology, 54.5 nasal, nobody presented bronchial symptoms and a 9% asymptomatic was reported. We support that the immediate skin test latex for Prick is an important parameter of support diagnosis for allergy to type 1 latex.

  10. Nitrile versus Latex for Glove Juice Sampling.

    Science.gov (United States)

    Landers, Timothy F; Dent, Anthony

    2014-01-01

    The objective of this study was to explore the utility of nitrile gloves as a replacement for latex surgical gloves in recovering bacteria from the hands. Two types of nitrile gloves were compared to latex gloves using the parallel streak method. Streaks of Klebsiella pneumoniae and Staphylococcus aureus were made on tryptic soy agar plates, and the zones of inhibition were measured around pieces of glove material placed on the plates. Latex gloves produced a mean zone of inhibition of 0.28 mm, compared to 0.002 mm for nitrile gloves (pnitrile may be a viable alternative to latex in glove juice sampling methods, since nitrile avoids the risk of latex exposure.

  11. NANOMODIFIED CONCRETE

    Directory of Open Access Journals (Sweden)

    B. M. Khroustalev

    2015-01-01

    Full Text Available One of the main directions in construction material science is the development of  next generation concrete that is ultra-dense, high-strength, ultra-porous, high heat efficient, extra corrosion-resistant. Selection of such direction is caused by extreme operational impacts on the concrete, namely: continuously increasing load on the concrete and various dynamics of such loads; the necessity in operation of concrete products in a wide temperature range and their exposure to various chemical and physical effects.The next generation concrete represents high-tech concrete mixtures with additives that takes on and retain the required properties when hardening and being used under any operational conditions. A differential characteristic of the next generation concrete is its complexity that presumes usage of various mineral dispersed components, two- and three fractional fine and coarse aggregates, complex chemical additives, combinations of polymer and iron reinforcement.Design strength and performance properties level of the next generation concrete is achieved by high-quality selection of the composition, proper selection of manufacturing techniques, concrete curing, bringing the quality of concrete items to the required level of technical condition during the operational phase. However, directed formation of its structure is necessary in order to obtain high-tech concrete.Along with the traditional methods for regulation of the next generation concrete structure, modification of concrete while using silica nanoparticles is also considered as a perspective one because the concrete patterning occurs due to introduction of a binder in a mineral matrix. Due to this it is possible to obtain nano-modified materials with completely new properties.The main problem with the creation of nano-modified concrete is a uniform distribution of nano-materials in the volume of the cement matrix which is particularly important in the cases of adding a modifier in

  12. Cryo-SEM studies of latex/ceramic nanoparticle coating microstructure development.

    Science.gov (United States)

    Luo, Hui; Scriven, L E; Francis, Lorraine F

    2007-12-15

    Cryogenic scanning electron microscopy (cryo-SEM) was used to investigate microstructure development of composite coatings prepared from dispersions of antimony-doped tin oxide (ATO) nanoparticles (approximately 30 nm) or indium tin oxide (ITO) nanoparticles (approximately 40 nm) and latex particles (polydisperse, D(v): approximately 300 nm). Cryo-SEM images of ATO/latex dispersions as-frozen show small clusters of ATO and individual latex particles homogeneously distribute in a frozen water matrix. In contrast, cryo-SEM images of ITO/latex dispersions as-frozen show ITO particles adsorb onto latex particle surfaces. Electrostatic repulsion between negatively charged ATO and negatively charged latex particles stabilizes the ATO/latex dispersion, whereas in ITO/latex dispersion, positively charged ITO particles are attracted onto surfaces of negatively charged latex particles. These results are consistent with calculations of interaction potentials from past research. Cryo-SEM images of frozen and fractured coatings reveal that both ceramic nanoparticles and latex become more concentrated as drying proceeds; larger latex particles consolidate with ceramic nanoparticles in the interstitial spaces. With more drying, compaction flattens the latex-latex particle contacts and shrinks the voids between them. Thus, ceramic nanoparticles are forced to pack closely in the interstitial spaces, forming an interconnected network. Finally, latex particles partially coalesce at their flattened contacts, thereby yielding a coherent coating. The research reveals how nanoparticles segregate and interconnect among latex particles during drying.

  13. Possibilities for improving corrosion protection of reinforced concrete by modified hydrotalcites: a literature review

    NARCIS (Netherlands)

    Yang, Z.; Fischer, H.R.; Polder, R.B.

    2012-01-01

    Modified Hydrotalcites (MHTs) represent a group of technologically promising materials for improving corrosion protection in concrete owing to their low cost, relative simplicity of preparation, and plenty of composition variables. Numerous academic and commercial studies on MHTs have been carried

  14. Development of Flat Roof Construction with Waterproofing from Modified Self-Compacting Concrete

    Science.gov (United States)

    Bogdanov, R. R.; Ibragimov, R. A.

    2017-11-01

    The given article considers the issues of increase of building flat roof durability by application of the modified self-compacting concrete (SSC). When SSC was modified, a complex modifier was developed and the optimization of the complex modifier composition was carried out using a three-factor experiment. The physico-mechanical properties of the obtained SSC are determined. The microstructure and phase composition of the modified cement stone were studied. On the basis of the studies carried out, namely, X-ray phase analysis and electron microscopy, it was concluded that the reduced content of calcium hydroxide in the samples with a complex modifier is due to the adsorption of calcium hydroxide on highly dispersed particles and the reaction of interaction with metakaolin also contributing to reduction in the content of calcium hydroxide in cement stone. The received data allow one to speak about SSC high operational characteristics. With the mark for the spreading of cone P5, the modified SSC has a class of compressive strength B50, high frost resistance (F600) and water resistance (W16).

  15. Emotion with tears decreases allergic responses to latex in atopic eczema patients with latex allergy.

    Science.gov (United States)

    Kimata, Hajime

    2006-07-01

    Allergic responses are enhanced by stress, whereas they are reduced by laughter in atopic eczema patients. Emotion with tears decreases plasma IL-6 levels in patients with rheumatoid arthritis. Thus, the effect of emotion with tears on allergic responses in patients with atopic eczema was studied. Sixty patients with atopic eczema having latex allergy viewed both the weather information video and the heart-warming movie, Kramer vs. Kramer. Just before and immediately after viewing each video, allergic responses to latex were measured. Viewing the weather information video did not cause emotion with tears in any patients, and it failed to modulate allergic responses. In contrast, viewing Kramer vs. Kramer caused emotion with tears in 44 of 60 patients, and it reduced allergic skin wheal responses to latex and latex-specific IgE production in them. Emotion with tears reduced allergic responses, and it may be useful in the treatment of allergic diseases.

  16. Experimental study on the drying of natural latex medical gloves

    Science.gov (United States)

    Chankrachang, Mano; Yongyingsakthavorn, Pisit; Tohsan, Atitaya; Nontakaew, Udomkiat

    2018-01-01

    The purpose of this research was to study latex film drying at 70 °C using a laboratory drying oven. Two different total solid content (TSC) latex compounds, which 45% TSC and 35% TSC were used. The undried latex films were prepared according to the common procedures used in latex gloves manufacturers, that is, by dry coagulant dipping process. The experimental results such as initial moisture content, the amount of moisture and drying time of latex films in each latex compound formula were determined. After that, the results were projected to calculate on the production capacity expand by 1 million piece/day of natural latex medical gloves. Finally, the rate of moisture entering the latex drying oven and the energy consumption of the drying oven were estimated. The results indicated that when the 35% TSC of latex compound was used. The initial moisture content of latex film was higher than 45% TSC of latex compound about 7%. The drying time of 35% TSC was longer than 45% TSC for 2.5 min and consume more energy about 10%. As a result, the 45% TSC latex compound was the better way to saving energy and managing humidity in the production line. Therefore, it was found to very useful to an approximate design length and size of actual of latex drying oven and the rate of moisture entering the oven as well.

  17. Bonding Characteristics of Macrosynthetic Fiber in Latex-Modified Fiber-Reinforced Cement Composites as a Function of Carbon Nanotube Content

    Directory of Open Access Journals (Sweden)

    Ji-Hong Jean

    2016-01-01

    Full Text Available The effect of carbon nanotube content (0, 0.5, 1.0, 1.5, and 2.0% of the cement weight on the bonding properties of macrosynthetic fiber in latex-modified hybrid fiber cement-based composites (LMHFRCCs was evaluated. The slump value, compressive strength, and bonding strength were measured for each LMHFRCC. As the carbon nanotube content increased to 1.5%, the bonding properties of the macrosynthetic fiber improved. However, the bonding performance deteriorated at a carbon nanotube content of 2.0%. A decrease in the fluidity of the mix negatively affected the dispersion of the nanotubes in the LMHFRCCs. The addition of carbon nanotubes also affected the relative bonding strength independently of the improvement in compressive strength. Microscopic analysis of the macrosynthetic fiber surfaces was used to understand changes in the bonding behavior.

  18. Nitrile versus Latex for Glove Juice Sampling.

    Directory of Open Access Journals (Sweden)

    Timothy F Landers

    Full Text Available The objective of this study was to explore the utility of nitrile gloves as a replacement for latex surgical gloves in recovering bacteria from the hands. Two types of nitrile gloves were compared to latex gloves using the parallel streak method. Streaks of Klebsiella pneumoniae and Staphylococcus aureus were made on tryptic soy agar plates, and the zones of inhibition were measured around pieces of glove material placed on the plates. Latex gloves produced a mean zone of inhibition of 0.28 mm, compared to 0.002 mm for nitrile gloves (p<.001. While the parallel streak method is not intended as a quantitative estimate of antimicrobial properties, these results suggest that nitrile may be a viable alternative to latex in glove juice sampling methods, since nitrile avoids the risk of latex exposure.

  19. Latex and friends

    CERN Document Server

    Dongen, M R C van

    2012-01-01

    LaTeX is a free, automated state-of-the-art typesetting system. This book teaches all the ins and outs of LaTeX which are needed to write an article, report, thesis, or book. The book teaches by example, giving many worked out examples showing input and output side by side. The book presents the most recent techniques for presenting data plots, complex graphics, and computer presentations, but does not require previous knowledge. However, it is also a reference for the more seasoned user, with pointers to modern techniques and packages. Recurring themes in the book are consistent and effective

  20. Cement-latex grouting mortar for cementing boreholes

    Energy Technology Data Exchange (ETDEWEB)

    Kateev, I S; Golyshkina, L A; Gorbunova, I V; Kurochkin, B M; Vakula, Ya V

    1980-01-01

    The need for the development of cement-latex grouting mortar for the purpose of separating strata when reinforcing boreholes at deposits in the Tatar Associated SSR is evaluated. Results of studies of the physical and mechanical properties of cement-latex grouting mortar systems (mortar plus brick) are presented. Formulas for preparing cement-latex grouting mortor are evaluated and results of industrial tests of such mortars shown.

  1. Jackfruit anaphylaxis in a latex allergic patient.

    Science.gov (United States)

    Wongrakpanich, Supakanya; Klaewsongkram, Jettanong; Chantaphakul, Hiroshi; Ruxrungtham, Kiat

    2015-03-01

    Several fruits have been reported to crossreact with latex antigen in latex allergy patients but little is known regarding tropical fruits in particular. Here we report the case of a 34-year old nurse who developed anaphylaxis following the ingestion of dried jackfruit (Artocarpus heterophyllus). The patient had a history of chronic eczema on both hands resulting from a regular wear of latex gloves. She and her family also had a history of atopy (allergic rhinitis and/or atopic dermatitis). The results of skin prick tests were positive for jackfruit, latex glove, kiwi and papaya, but the test was negative for banana. While we are reporting the first case of jackfruit anaphylaxis, further research needs to be conducted to identify the mechanisms underlying it. In particular, in-vitro studies need to be designed to understand if the anaphylaxis we describe is due to a cross reactivity between latex and jackfruit or a coincidence of allergy to these 2 antigens.

  2. A novel arctigenin-containing latex glove prevents latex allergy by inhibiting type I/IV allergic reactions.

    Science.gov (United States)

    Wang, Yong-Xin; Xue, Dan-Ting; Liu, Meng; Zhou, Zheng-Min; Shang, Jing

    2016-03-01

    The present study aimed at developing a natural compound with anti-allergic effect and stability under latex glove manufacturing conditions and investigating whether its anti-allergic effect is maintained after its addition into the latex. The effects of nine natural compounds on growth of the RBL-2H3 cells and mouse primary spleen lymphocytes were determined using MTT assay. The compounds included glycyrrhizin, osthole, tetrandrine, tea polyphenol, catechin, arctigenin, oleanolic acid, baicalin and oxymatrine. An ELISA assay was used for the in vitro anti-type I/IV allergy screening; in this process β-hexosaminidase, histamine, and IL-4 released from RBL-2H3 cell lines and IFN-γ and IL-2 released from mouse primary spleen lymphocytes were taken as screening indices. The physical stability of eight natural compounds and the dissolubility of arctigenin, selected based on the in vitro pharnacodynamaic screening and the stability evaluation, were detected by HPLC. The in vivo pharmacodynamic confirmation of arctigenin and final latex product was evaluated with a passive cutaneous anaphylaxis (PCA) model and an allergen-specific skin response model. Nine natural compounds showed minor growth inhibition on RBL-2H3 cells and mouse primary spleen lymphocytes. Baicalin and arctigenin had the best anti-type I and IV allergic effects among the natural compounds based on the in vitro pharmacodynamic screening. Arctigenin and catechin had the best physical stability under different manufacturing conditions. Arctigenin was the selected for further evaluation and proven to have anti-type I and IV allergic effects in vivo in a dose-dependent manner. The final product of the arctigenin-containing latex glove had anti-type I and IV allergic effects in vivo which were mainly attributed to arctigenin as proved from the dissolubility results. Arctigenin showed anti-type I and IV allergic effects in vitro and in vivo, with a good stability under latex glove manufacturing conditions

  3. Modification of asphaltic concrete with a mineral polymeric additive based on butadiene-styrene rubber and chemically precipitated calcium carbonate

    Directory of Open Access Journals (Sweden)

    S. I. Niftaliev

    2016-01-01

    Full Text Available Modification of asphaltic concrete with a mineral polymeric additive based on butadiene – styrene rubber and chemically precipitated calcium carbonate. This paper presents the results of the study of physical – mechanical and service properties of the asphaltic concrete modified with the mineral polymeric composition. Calcium carbonate is used both as a filler and a coagulant. The chalk was preliminarily ground and hydrophobizated by stearic acid. These operations contribute to even distribution of the filler and interfere with lump coagulation. As a result of the experiments, it was found that the best results were obtained by combining the operations of dispersion and hydrophobization. The optimal amount of stearic acid providing the finest grinding in a ball mill is a content from 3 to 5% by weight. The optimal grinding time of the filler was found (4–6 hours. With increasing dispersion time the particles form agglomerates. Filling the butadiene styrene latex with the hydrophobic fine-grained calcium carbonate was carried out in the laboratory mixer. As a result of the experimental works, it was found that the best distribution of the filler takes place with ratio of rubber: chalk – 100:400. The resulting modifier was subjected to the thermal analysis on the derivatograph to determine its application temperature interval. A marked reduction in weight of the mineral polymeric modifier begins at 350 °C. Thus, high temperature of the modifier destruction allows to use it at the temperature of the technological process of asphaltic concrete preparation (up to 170 °C. It was found that an increase in the amount of the carbonate filler in the rubber SKS 30АRК significantly increases its thermal resistance and connection of the polymer with the chalk in the composition.

  4. Allergy to latex in health workers

    Directory of Open Access Journals (Sweden)

    Fajardo-Zapata, Álvaro L.

    2015-01-01

    Full Text Available Introduction: A common and growing problem in hospitals is hypersensitivity to rubber latex antigens, since many products, including gloves, are manufactured from this material, with the consequent possibility of producing allergy in persons who use them. Objective: To find out if health workers at a fourth level clinic in Bogotá, Colombia, are allergic to rubber latex, in relation to the use of gloves. Materials and methods: Descriptive, cross-sectional study of a non-probabilistic intentional-type sample in each one of four hospital units. A survey was applied to participants. Results: 16 of the 26 persons (61.5% with history of allergic processes manifested some kind of reaction when they had contact with latex gloves; the problem was more significant in the nursing personnel compared to physicians. Conclusions: The exposure to latex gloves may be generating the appearance of allergic occupational disease in health workers.

  5. Balanced improvement of high performance concrete material properties with modified graphite nanomaterials

    Science.gov (United States)

    Peyvandi, Amirpasha

    Graphite nanomaterials offer distinct features for effective reinforcement of cementitious matrices in the pre-crack and post-crack ranges of behavior. Thoroughly dispersed and well-bonded nanomaterials provide for effective control of the size and propagation of defects (microcracks) in matrix, and also act as closely spaced barriers against diffusion of moisture and aggressive solutions into concrete. Modified graphite nanomaterials can play multi-faceted roles towards enhancing the mechanical, physical and functional attributes of concrete materials. Graphite nanoplatelets (GP) and carbon nanofibers (CNF) were chosen for use in cementitious materials. Experimental results highlighted the balanced gains in diverse engineering properties of high-performance concrete realized by introduction of graphite nanomaterials. Nuclear Magnetic Resonance (NMR) spectroscopy was used in order to gain further insight into the effects of nanomaterials on the hydration process and structure of cement hydrates. NMR exploits the magnetic properties of certain atomic nuclei, and the sensitivity of these properties to local environments to generate data which enables determination of the internal structure, reaction state, and chemical environment of molecules and bulk materials. 27 Al and 29Si NMR spectroscopy techniques were employed in order to evaluate the effects of graphite nanoplatelets on the structure of cement hydrates, and their resistance to alkali-silica reaction (ASR), chloride ion diffusion, and sulfate attack. Results of 29Si NMR spectroscopy indicated that the percent condensation of C-S-H in cementitious paste was lowered in the presence of nanoplatelets at the same age. The extent of chloride diffusion was assessed indirectly by detecting Friedel's salt as a reaction product of chloride ions with aluminum-bearing cement hydrates. Graphite nanoplatelets were found to significantly reduce the concentration of Friedel's salt at different depths after various periods

  6. Synthesis and characterization of novel polyacid-stabilized latexes.

    Science.gov (United States)

    Yang, Pengcheng; Armes, S P

    2012-09-18

    A series of novel polyacid macromonomers based on 2-hydroxypropyl methacrylate (HPMA) were prepared by atom transfer radical polymerization (ATRP) via a two-step route. First, a range of well-defined PHPMA homopolymer precursors were synthesized by ATRP using a tertiary amine-functionalized initiator, 2-(dimethylamino)ethyl-2-bromoisobutyrylamide, and a CuCl/2, 2'-bipyridine (bpy) catalyst in alcoholic media at 50 °C. ATRP polymerizations were relatively slow and poorly controlled in pure isopropanol (IPA), especially when targeting higher degrees of polymerization (DP > 30). Improved control was achieved by addition of water: low polydispersity (M(w)/M(n) propyl methacrylate) (PSPMA) macromonomers by quaternizing the tertiary amine end-group with excess 4-vinylbenzyl chloride, followed by esterification of the pendent hydroxyl groups using excess succinic anhydride at 20 °C. These polyacid macromonomers were evaluated as reactive steric stabilizers for polystyrene latex synthesis under either aqueous emulsion polymerization or alcoholic dispersion polymerization conditions. Near-monodisperse polystyrene latexes were obtained via aqueous emulsion polymerization using 10 wt % PSPMA macromonomer (with respect to styrene monomer) with various initiators as evidenced by scanning electron microscopy, disk centrifuge photosedimentometry and light scattering studies. PSPMA macromomer concentrations as low as 1.0 wt % also produced near-monodisperse latexes, suggesting that these PSPMA macromonomers are highly effective stabilizers. Alcoholic dispersion polymerization of styrene conducted in various ethanol/water mixtures with 10 wt % PSPMA(50) macromonomer produced relatively large near-monodisperse latexes. Increasing the water content in such formulations led to smaller latexes, as expected. Control experiments conducted with 10 wt % PSPMA(50) homopolymer produced relatively large polydisperse latexes via emulsion polymerization and only macroscopic precipitates via

  7. Extractable proteins from field radiation vulcanized natural rubber latex

    Energy Technology Data Exchange (ETDEWEB)

    Parra, Duclerc F. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)]. E-mail: dfparra@ipen.br; Pinto Martins, Carlos Felipe [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Collantes, Hugo D.C. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Lugao, Ademar B. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)

    2005-07-01

    The type I allergy associated with the use of natural rubber latex (NRL) products is caused by the NRL proteins leached by the sweat or other body fluids. Makuuchi's group proposed for the first time the proteins removal by the addition of water-soluble polymers (WSP) on radiation vulcanization of natural rubber latex (RVNRL) that is a promising process under development in many countries. In this study, Brazilian field natural rubber was irradiated with a {sup 60}Co gamma source to reduce the content of WSP in the final product. WSP was used as additive to improve the extraction of protein. After irradiation the RVNRL was centrifuged to extract the WSP and proteins. The analytical methodology for protein content was based on the modified Lowry method according to ASTM D5712. Protein determination was carried out in serum of latex and in the extracts of the gloves. The concentration of extractable water-soluble proteins in serum of irradiated field NRL (NRL1), not irradiated one (NRL2); of twice centrifuged sample with polymer additive NRL (NRL3) and of the glove manufactured (NRLG) are compared with commercial glove (CG). The irradiation process increases the extractable water-soluble proteins, EP, as reported in the literature. In this study the use of polymeric additive on the bi-centrifugation process to remove protein was successful and the EP of the glove obtained in NRL3 was at around 40% of the commercial glove.

  8. The preparation of RVNRL using Malaysian-produced latexes

    International Nuclear Information System (INIS)

    Zin, W.M. bin W.; Mohid, N. bte; Hasan, J. bin; Noor, W.K.A. bte W.M.; Jaafar, Zulkifli

    1993-01-01

    This research project was carried out using latexes supplied by three of the suppliers in Malaysia. From the results of studies carried out in search of the best sensitiser for RVNRL preparation, the use of n-butyl acrylate (n-BA) as a sensitiser gave the most promising results. However, its use as a sensitiser is not universal to all latexes available in the country. The problem was overcome by using different formulations for different latexes. For the latex supplied by Golden Hope (Hytex), a combination of sensitisers i.e. n-BA plus 2-ethyl hexyl acrylate (2-EHA) with a 10% potassium hydroxide solution as the stabilizer, was required. Latex supplied by MARDEC (Matex), seemed to need only n-BA as the sensitiser. However, a stabilizer was still required and the use of a 10% KOH solution was found to be suitable. A large range of stabilizers and sensitisers were applicable to Guthrie latex. The use of n-BA as the sensitiser and potassium laurylic acid as the stabilizer seemed the most favourable formulation. All the results are discussed in the form of a correlation between dose and the tensile properties of RVNRL vulcanizates, equilibrium swelling ratio and standing time of the latex formulation. (author)

  9. Plant latex lipase as biocatalysts for biodiesel production | Mazou ...

    African Journals Online (AJOL)

    Plant latex lipase as biocatalysts for biodiesel production. ... This paper provides an overview regarding the main aspects of latex, such as the reactions catalyzed, physiological functions, specificities, sources and their industrial applications. Keywords: Plant latex, lipase, Transesterification, purification, biodiesel ...

  10. Ten years incidence of natural rubber latex sensitization and symptoms in a prospective cohort of health care workers using non-powdered latex gloves 2000-2009.

    Science.gov (United States)

    Larese Filon, Francesca; Bochdanovits, Letizia; Capuzzo, Chiara; Cerchi, Roberto; Rui, Francesca

    2014-07-01

    To assess the incidence of sensitization and gloves-related symptoms in 10-year follow-up in a group of health care workers (9,660 person-years) using non-powdered latex gloves from 2000 to 2009 and to examine related factors. We studied 2,053 health care workers in Trieste Hospitals by means of skin prick test for latex extract, patch tests and medical examinations. We report the incidence of latex sensitization among workers using non-powdered latex gloves. The incidence of latex sensitization, rhinitis, asthma, urticaria, irritant and allergic contact dermatitis were 1.0; 0.12; 0.21; 0.72; 2.39 and 2.50 cases per 1,000 person-years, respectively. Respiratory symptoms and urticaria were positively related with latex sensitization (OR = 8.0; 95 % CL 1.27-48.6), with common allergic respiratory symptoms (OR = 4.19; 95 % CL 1.04-16.8) and with familial atopy (OR = 4.47; 95 % CL 1.1-17.9). The incidence of latex sensitization and latex-related symptoms were very low but subjects with allergic symptoms related to common allergens are at higher risk. The use of non-latex gloves is suggested for them.

  11. Some Properties of Polymer Modified Self-Compacting Concrete Exposed to Kerosene and Gas Oil

    Directory of Open Access Journals (Sweden)

    Nada Mahdi Fawzi

    2017-01-01

    Full Text Available This thesis aims to study the effect of addition polymer materials on mechanical properties of self-compacting concrete, and also to assess the influence of petroleum products (kerosene and gas oil on mechanical properties of polymer modified self-compacting concrete (PMSCC after different exposure periods of (30 ,60 ,90 ,and 180 days. Two type of curing are used; 28 days in water for SCC and 2 days in water followed 26 days in air for PMSCC. The test results show that the PMSCC (15% P/C ratio which is exposed to oil products recorded a lower deterioration in compressive strength's values than reference concrete. The percentages of reduction in compressive strength values of PMSCC (15% P/C ratio was (6.03% and (9.61% up to 180 days of exposure to kerosene and gas oil respectively, relative to the same mix immersed in water, while the percentages of reduction in compressive strength values of SCC (reference concrete was (21.18% and (25.19% up to 180 days of exposure to kerosene and gas oil respectively, relative to the same mix immersed in water. Flexural strength results present improvement for all ages and for all concrete mixes with all percentages of polymer content The total water absorption values of PMSCC (15% P/C ratio showed a better performance than reference concrete mix when exposed to oil products. It was (1.34, 2.21, 2.17 % up to 180 days with samples immersed in water, kerosene, and gas oil respectively, with percentages of reduction of (23.86%, (33.83%, and (31.33% relative to the SCC (reference concrete.

  12. More math into Latex

    CERN Document Server

    Grätzer, George

    2007-01-01

    For close to two decades, Math into Latex has been the standard introduction and complete reference for writing articles and books containing mathematical formulas. In this fourth edition, the reader is provided with important updates on articles and books. An important new topic is discussed: transparencies (computer projections). Key features of More Math into Latex, 4th edition: Installation instructions for PC and Mac users; An example-based, visual approach and a gentle introduction with the Short Course; A detailed exposition of multiline math formulas with a Visual Guide; A unified appr

  13. Evaluating The Performance of Asphalt Concrete Mixes by Utilizing Carbon Black as Asphalt Modifier

    Directory of Open Access Journals (Sweden)

    Aliaa Faleh Al.ani

    2018-02-01

    Full Text Available Carbon black produced from several factories in Iraq is expected to provide a reinforcing agent for asphalt paving materials. Carbon black has many characteristics that distinguish  it from conventional mineral fillers, as well as their different function in pavement mixtures. Theory and exercise advanced  in the inclusive utilize of carbon black as a reinforcing agent for rubber has led to concept of asphalt reinforcement. The very fine particles of micro filler added in different contents will be dispersed in asphalt cement improving the mechanical properties of asphalt concrete mixes. In this Four percentages rates were utilized; 0, 3, 6, and 9 percent adding to asphalt grade (60-70. Mixes of asphalt concrete were destined at their optimum asphalt content (OAC then experienced to assess their engineering characteristics that contain moisture of damage, permanent deformation, modulus of resilient and characteristics of fatigue. These characteristics have been assessed utilizing indirect tensile strength, uniaxial repeated loading and repeated flexural beam tests. Mixtures improved with carbon black were existed to have amended permanent deformation and fatigue characteristics, else exhibited high resilient modulus and lower moisture susceptibility. Result showed that a rate changed from 3 to 9 percent has shown an increase in resilient modulus for increment of carbon black and modulus of resilient for mixes with 9 percent carbon black was 1.4 times that for mixes with 0 percent carbon black. The altering of carbon black from a range (3-9 percent has modified the fatigue property of the asphalt concrete mixes as determined by flexural test, Significantly, to modify the asphalt concrete manner taken the  percent of carbon black 6, and to produce the mixes more durable , higher resistance to distresses by adding the local knowledge.

  14. Recombinant albumin monolayers on latex particles.

    Science.gov (United States)

    Sofińska, Kamila; Adamczyk, Zbigniew; Kujda, Marta; Nattich-Rak, Małgorzata

    2014-01-14

    The adsorption of recombinant human serum albumin (rHSA) on negatively charged polystyrene latex micro-particles was studied at pH 3.5 and the NaCl concentration range of 10(-3) to 0.15 M. The electrophoretic mobility of latex monotonically increased with the albumin concentration in the suspension. The coverage of adsorbed albumin was quantitatively determined using the depletion method, where the residual protein concentration was determined by electrokinetic measurements and AFM imaging. It was shown that albumin adsorption was irreversible. Its maximum coverage on latex varied between 0.7 mg m(-2) for 10(-3) M NaCl to 1.3 mg m(-2) for 0.15 M NaCl. The latter value matches the maximum coverage previously determined for human serum albumin on mica using the streaming potential method. The increase in the maximum coverage was interpreted in terms of reduced electrostatic repulsion among adsorbed molecules. These facts confirm that albumin adsorption at pH 3.5 is governed by electrostatic interactions and proceeds analogously to colloid particle deposition. The stability of albumin monolayers was measured in additional experiments where changes in the latex electrophoretic mobility and the concentration of free albumin in solutions were monitored over prolonged time periods. Based on these experimental data, a robust procedure of preparing albumin monolayers on latex particles of well-controlled coverage and molecule distribution was proposed.

  15. Effect of Amphiphilic Alkyl Chain Length Upon Purified LATEX Stability

    International Nuclear Information System (INIS)

    Amira Amir Hassan; Amir Hashim Mohd Yatim

    2015-01-01

    Rubber particles in purified latex (PL) are stabilized by a film of protein and fatty acid soap (surfactant). Saturated straight-chain fatty acid soaps can assist an enhancement of latex stability. However, whether the alkyl chain length plays an important role in increasing the stability is still an issue. The aim of this study is to investigate the effect of alkyl chain length of anionic surfactant on the stability of purified latex. The fatty acid soap of decanoate (9), laurate (11), sodium dodecyl sulphate (SDS) (12) and palmitate (15) were used. The numbers in parentheses indicating the number of carbon present in alkyl chain of the soap. The results showed that the impact of alkyl chain length on the stability of latex is in the order of laurate > decanoate > SDS > palmitate > purified latex accordingly. The alkyl chain length does giving a significant effect on latex stability after longer stirring time. The particle size of latex with the presence of surfactant is greater compare to a single particle itself due to extension of particles diameter. Thus suitable interaction of the nonpolar tail of surfactant with the hydrophobic regions of latex surface played a major role in maintaining a stable latex system. (author)

  16. The Synthesis and Modification of Nanosized Clickable Latex Particles

    KAUST Repository

    Almahdali, Sarah

    2013-05-01

    This research aims to add to the current knowledge available for miniemulsion polymerization reactions and to use this knowledge to synthesize multifunctional nanosized latex particles that have the potential to be used in catalysis. The physical properties of the latex can be adjusted to suit various environments due to the multiple functional groups present. For this research, styrene, pentafluorostyrene, azidomethyl styrene, pentafluorostyrene with azidomethyl styrene and pentafluorostyrene with styrene latexes were produced, and analyzed by dynamic light scattering. The latexes were synthesized using a miniemulsion polymerization technique found through this research. Potassium oleate and potassium 1,1,2,2,3,3,4,4-nonafluorobutane-1-sulfonate were used as surfactants during the miniemulsion polymerization reaction to synthesize pentafluorostyrene with azidomethyl styrene latex. Transmission electron microscopy data and dynamic light scattering data have been collected to analyze the structure of this latex, and it has been synthesized using a number of conditions, differing in reaction time, surfactant amount and sonication methods. We have also improved the solubility of the latex through a copper(I) catalyzed 1,3-dipolar azide-alkyne reaction, by clicking (polyethylene glycol)5000 onto the azide functional groups.

  17. Marshall properties of asphalt concrete using crumb rubber modified of motorcycle tire waste

    Science.gov (United States)

    Siswanto, Henri; Supriyanto, Bambang; Pranoto, Chandra, Pria Rizky; Hakim, Arief Rahman

    2017-09-01

    The aim of this study is to explain the effect of Crumb Rubber Modified (CRM) of motorcycle tire waste on Marshall properties of asphalt mix. Two types of aggregate gradation, asphalt concrete wearing course (ACWC) and asphalt concrete base (ACB), and CRM passing #50 sieve size were used. Seven levels of CRM content were investigated in this study, namely 0%, 0.5%, 1%, 1.5%, 3%, 4.5%, and 6% by weight of aggregate. Marshall test is conducted on Marshall specimens. The specimens are tested in their optimum binder content (OBC). The results indicate that CRM addition of motorcycle tire waste increases the Marshall stability of the both mix, ACWC and ACB. In addition, 1% CRM addition of motorcycle tire waste of the total mix weight is the best mix.

  18. [Latex allergy in a paediatric hospital. Characteristics and risk factors].

    Science.gov (United States)

    Bailey, Michael; Norambuena, Ximena; Roizen, Gigia; Rodríguez, Jorge; Quezada, Arnoldo

    The prevalence of latex sensitisation varies according to the population studied. There are various risk factors that increase latex sensitisation, such as genetic risk, atopy, and multiple surgeries. To characterise patients referred to an Immunology Unit with suspected latex allergy, and to analyse their clinical features and risk factors. A retrospective, descriptive study was conducted on children suspected of latex allergy. Their medical records were reviewed in order to assess symptoms with contact or exposure to latex materials. Known risk factors to latex sensitisation, such as pathologies requiring repeated surgery (spina bifida, myelomeningocele, scoliosis and nephro-urological alterations), atopy (rhinitis, asthma, atopic dermatitis) were investigated. A prick test and/or specific IgE to latex were also performed. A multivariate logistic regression model was performed to find associations between symptoms triggered by exposure to latex with underlying diseases and other risk conditions. A total of 106 patients were enrolled in the study, of whom 50 were evaluable. At diagnosis 96% of patients were older than five years. Most of the risk factors described were observable in these patients, such as multiple surgeries, neurological and nephro-urological malformations, surgery before one year-old, and repeated bladder catheterisation. After latex exposure, mucous cutaneous manifestations were the most common (52%), followed by respiratory symptoms (36%). All patients were sensitised and allergic to latex. Latex allergy is a significant problem in children with risk factors. The results shown in this study raise important challenges for preventive measures and awareness. Copyright © 2016 Sociedad Chilena de Pediatría. Publicado por Elsevier España, S.L.U. All rights reserved.

  19. Isolation and characterization of latex-specific promoters from Papaver somniferum L.

    OpenAIRE

    Raymond, Michelle Jean

    2004-01-01

    The pharmacologically important alkaloids morphine and codeine are found in latex of opium poppy (Papaver somniferum). Latex is harbored in laticifers, a specialized vascular cell-type. Isolation and characterization of latex-specific genes may provide a useful tool to metabolically engineer increased alkaloid production. Previous research in the Nessler laboratory identified genes that exhibit latex-specific gene expression. Latex-specific genes were an 2-oxoglutarate-dioxygense (DIOX), ...

  20. Gloves against mineral oils and mechanical hazards: composites of carboxylated acrylonitrile-butadiene rubber latex.

    Science.gov (United States)

    Krzemińska, Sylwia; Rzymski, Władysław M; Malesa, Monika; Borkowska, Urszula; Oleksy, Mariusz

    2016-09-01

    Resistance to permeation of noxious chemical substances should be accompanied by resistance to mechanical factors because the glove material may be torn, cut or punctured in the workplace. This study reports on glove materials, protecting against mineral oils and mechanical hazards, made of carboxylated acrylonitrile-butadiene rubber (XNBR) latex. The obtained materials were characterized by a very high resistance of the produced materials to oil permeation (breakthrough time > 480 min). The mechanical properties, and especially tear resistance, of the studied materials were improved after the addition of modified bentonite (nanofiller) to the XNBR latex mixture. The nanocomposite meets the requirements in terms of parameters characterizing tear, abrasion, cut and puncture resistance. Therefore, the developed material may be used for the production of multifunctional protective gloves.

  1. Thermodynamics of swelling of latex particles with two monomers

    NARCIS (Netherlands)

    Maxwell, I.A.; Kurja, J.; van Doremaele, G.H.J.; German, A.L.

    1992-01-01

    The partitioning of 2 monomers between the latex particle, monomer droplet, and aq. phases of an emulsion polymer latex are measured at satn. swelling of the latex particle phase (corresponding to intervals I and II of an emulsion polymn.). The monomer (Me acrylate, Bu acrylate, styrene) and polymer

  2. Encapsulation of Clay Platelets inside Latex Particles

    NARCIS (Netherlands)

    Voorn, D.J.; Ming, W.; Herk, van A.M.; Fernando, R.H.; Sung, Li-Piin

    2009-01-01

    We present our recent attempts in encapsulating clay platelets inside latex particles by emulsion polymerization. Face modification of clay platelets by cationic exchange has been shown to be insufficient for clay encapsulation, leading to armored latex particles. Successful encapsulation of

  3. Novel approach to make concrete structures self-healing using porous network concrete

    NARCIS (Netherlands)

    Sangadji, S.; Schlangen, E.

    2012-01-01

    Many researchers proposed self healing mechanism using hollow fibres and or microcapsule containing a modifying agent dispersed in the concrete to prolong its service life and make it more durable. A novel self healing concrete concept is proposed in this paper by using porous network concrete

  4. Preparation of highly stabilised natural rubber latex for radiation vulcanisation

    International Nuclear Information System (INIS)

    Kulatunge, S.S.; Nadarajah, M.; Kalyani, N.M.V.; Chandralal, H.N.K.K.; Devendra, R.

    1996-01-01

    There is a bright future for radiation vulcanised natural rubber latex (RVNRL) but there are problems in manufacturing it as the centrifuged latex to be used for radiation has to be kept for at least a month or sometimes even three to six months before adding the sensitisers and even then the latex sometimes coagulates on adding the sensitisers. This paper describes a process by which the latex can be stabilised by addition of an anionic soap before centrifuging so that it has a high mechanical stability and hence can be used even within one week of the manufacture of the centrifuged latex

  5. Sulfonated macro-RAFT agents for the surfactant-free synthesis of cerium oxide-based hybrid latexes.

    Science.gov (United States)

    Garnier, Jérôme; Warnant, Jérôme; Lacroix-Desmazes, Patrick; Dufils, Pierre-Emmanuel; Vinas, Jérôme; van Herk, Alex

    2013-10-01

    Three types of amphiphatic macro-RAFT agents were employed as compatibilizers to promote the polymerization reaction at the surface of nanoceria for the synthesis of CeO2-based hybrid latexes. Macro-RAFT copolymers and terpolymers were first synthesized employing various combinations of butyl acrylate as a hydrophobic monomer and acrylic acid (AA) and/or 2-acrylamido-2-methylpropane sulfonic acid (AMPS) as hydrophilic monomers. After characterizing the adsorption of these macro-RAFT agents at the cerium oxide surface by UV-visible spectrometry, emulsion copolymerization reactions of styrene and methyl acrylate were then carried out in the presence of the surface-modified nanoceria. Dynamic Light Scattering and cryo-Transmission Electron Microscopy were employed to confirm the hybrid structure of the final CeO2/polymer latexes, and proved that the presence of acrylic acid units in amphiphatic macro-RAFT agents enabled an efficient formation of hybrid structures, while the presence of AMPS units, when combined with AA units, resulted in a better distribution of cerium oxide nanoclusters between latex particles. Copyright © 2013 Elsevier Inc. All rights reserved.

  6. The Morphology of Emulsion Polymerized Latex Particles

    Science.gov (United States)

    Wignall, G. D.; Ramakrishnan, V. R.; Linne, M. A.; Klein, A.; Sperling, L. H.; Wai, M. P.; Gelman, R. A.; Fatica, M. G.; Hoerl, R. H.; Fisher, L. W.

    1987-11-01

    Under monomer starved feed conditions, emulsion polymerization of perdeuterated methyl methacrylate and styrene in the presence of preformed polymethylmethacrylate latexes resulted in particles with a core-shell morphology, as determined by small-angle neutron scattering (SANS) analysis for a hollow sphere. The locus of polymerization of the added deuterated monomer is therefore at the particle surface. In similar measurements a statistical copolymer of styrene and methyl methacrylate was used as seed particles for further polymerization of trideuteromethyl methacrylate. The resulting polymer latex was again shown to have a core-shell morphological structure as determined by SANS. SANS experiments were also undertaken on polystyrene latexes polymerized by equilibrium swelling methods, with deuterated polymer forming the first or second step. The experiments covered a molecular weight range of 6 x 10{sup 4} 10{sup 6} the molecular weights are consistent with the experimental errors, indicating that the deuterium labeled molecules are randomly distributed in the latex. These results led to the finding that the polymer chains were constrained in the latex particles by factors of 2 to 4 from the relaxed coil dimensions. For M molecules. Several models were examined, including the possible development of core-shell structures at lower molecular weights.

  7. Sustainable monitoring of concrete structures : strength and durability performance of polymer-modified self-sensing concrete

    OpenAIRE

    Torgal, Fernando Pacheco; Gonzalez, J.; Jalali, Said

    2012-01-01

    Concrete structures all over the world are reaching the end of their service life sooner than expected. This is due to the fact that ordinary Portland cement-based concrete deteriorates under environmental actions and also that structural inspections and conservation actions are expensive. Besides, as they consume energy and non-renewable resources, they have negative environmental impacts. Self-sensing concrete provides an alternative way of monitoring concrete-reinforced structures...

  8. Troubleshooting for the observed problems in processing latex concentrate from natural resource

    International Nuclear Information System (INIS)

    Afreen, S; Haque, K R; Huda, M K

    2013-01-01

    Natural latex has special importance in the rubber industry for manufacturing different types of goods like gloves, balloons, male contraceptive and similar thin walled articles. This natural latex is much more sensitive a liquid to handle since it can easily become contaminated and thereby coagulated which makes it unfavourable for centrifuge and getting concentrate from it. Some other related measures also are included in consideration during the processing of concentrate latex from the natural raw latex. The problems that are being faced in a concentrate latex processing plant can be categorized in different groups like, problems related to the latex property, mechanical problems, electrical problems, handling and storage problems, transformation problems, problems related to environmental issues, etc. Among them, the most common and vital problems frequently observed in a concentrate latex processing plant are discussed here with a view to finding the measures for solution which will help to maintain the latex property in any latex processing plant.

  9. Gloves against mineral oils and mechanical hazards: composites of carboxylated acrylonitrile–butadiene rubber latex

    Science.gov (United States)

    Krzemińska, Sylwia; Rzymski, Władysław M.; Malesa, Monika; Borkowska, Urszula; Oleksy, Mariusz

    2016-01-01

    Resistance to permeation of noxious chemical substances should be accompanied by resistance to mechanical factors because the glove material may be torn, cut or punctured in the workplace. This study reports on glove materials, protecting against mineral oils and mechanical hazards, made of carboxylated acrylonitrile–butadiene rubber (XNBR) latex. The obtained materials were characterized by a very high resistance of the produced materials to oil permeation (breakthrough time > 480 min). The mechanical properties, and especially tear resistance, of the studied materials were improved after the addition of modified bentonite (nanofiller) to the XNBR latex mixture. The nanocomposite meets the requirements in terms of parameters characterizing tear, abrasion, cut and puncture resistance. Therefore, the developed material may be used for the production of multifunctional protective gloves. PMID:26757889

  10. Radiation vulcanization of Philippine natural rubber latex

    International Nuclear Information System (INIS)

    Dela Rosa, Alumanda M.; Abad, Lucille V.; Sta, Lorna P.; Ana-Relleve; Tranquilan-Aranilla, Charito O.; Pascual, Cristina L.

    1996-01-01

    The response of Philippine natural rubber latex to radiation vulcanization and the stability of the irradiated natural rubber latex (INRL) upon storage and aging were investigated. Commercially available high ammonia (HA) concentrated lattices obtained from various rubber plantations in Mindanao Island were treated with 5 phr of n-butyl acrylate (nBA), and gamma-irradiated at the PNRI sup 60 Co irradiation facility at dose rate of 2.57 KGy/hr. Unirradiated cast latex films gave different green strength which varied from 2 - 11 MPa. Cast films from INRL exhibited maximum tensile strengths of 25 - 32 MPa at a radiation dose of 15 kGy. Higher tensile strengths were obtained from cast films with low Mg and high nitrogen contents. Thermal analysis using thermogravimetry (TG) revealed one major decomposition product at 374 degree C - 377 degree C. Its rate of decomposition decreased to a minimum at 15 kGy, then increased as radiation dose increased. This trend correlated well with the tensile strength measurements. The stability of the INRL upon storage and aging is an essential parameter to the rubber latex industry. For storage studies, INRL was stored for various periods of time. It was found that the pH and total solids content of the stored INRL did not change significantly after 12 months of storage; the MST values remained at above 100 seconds, and the viscosity decreased with time. The cast films exhibited a decline in tensile strength, modulus 300% and crosslinking density upon storage. While there were observed changes in the physical properties of the IRNL during the storage period, the data indicate that these properties were within values acceptable to the latex industry. Tests on the aging properties of INRL film were undertaken. It was shown that among the chemical antioxidants presently used by the latex industry. TNPP demonstrated the highest antioxidant property, followed by Antage DAHQ and Vulcanox BKF. Our data indicate that the natural rubber latex

  11. Radiation vulcanization of Philippine natural rubber latex

    International Nuclear Information System (INIS)

    Dela Rosa, A.M.; Abad, L.V.; Sta.Ana-Relleve, L.P.; Tranquilan-Aranilla, C.O.; Pascual, C.L.

    1996-01-01

    The response of Philippine natural rubber latex to irradiation vulcanization and the stability of the irradiated natural rubber latex (INRL) upon storage and aging were investigated. Commercially available high ammonia (HA) concentrated latices obtained from various rubber plantations in Mindanao island were treated with 5 phr of n-butyl acrylate (nBA), and gamma-irradiated at the PNRI 60 Co irradiation facility at a dose rate of 2.57 kGy/hr. Unirradiated cast latex films gave different green strengths which varied from 2-11 MPa. Cast films from INRL exhibited maximum tensile strengths were obtained from cast films with low Mg and high nitrogen contents. Thermal analysis using thermogravimetry (TG) revealed one major decomposition product at 374 o -377 o C. Its rate of decomposition decreased to a minimum at 15 kGy, then increased as radiation dose was increased. This trend correlated well with the tensile strength measurements. The stability of the INRL upon storage and aging is an essential parameter to the rubbe latex industry. For storage studies, INRL was stored for various periods of time. It was found that the pH and total solids content of the stored INRL did not change significantly after 12 months of storage; the MST values remained at above 1000 seconds, and the viscosity decreased with time. The cast films exhibited a decline in tensile strength, modulus 300% , and crosslinking density upon storage. While there were observed changes in the physical properties of the INRL during the storage period, the data indicate that these properties were within values acceptable to the latex industry. Tests on the aging properties of INRL films were undertaken. It was shown that among the chemical antioxidants presently used by the latex industry, TNPP demonstrated the highest antioxidant property, followed by Antage DAHQ and Vulcanox BKF. Our data indicate that the natural rubber latex produced and processed in the Philippines is suited for radiation vulcanization

  12. CHARACTERIZATION AND RECYCLING OF WASTE WATER FROM GUAYULE LATEX EXTRACTION

    Science.gov (United States)

    Guayule commercialization for latex production to be used in medical products and other applications is now a reality. Currently, waste water following latex extraction is discharged into evaporation ponds. As commercialization reaches full scale, the liquid waste stream from latex extraction will b...

  13. EDITORIALS Latex allergy: 'Plight, rights and fights'

    African Journals Online (AJOL)

    anaphylaxis and life-threatening food allergies to cross-reacting fruit allergens such as kiwi, banana, tomato and chestnuts). Latex allergy is also encountered more frequently in children with spina bifida than in other hospitalised children.[7] Sensitisation is usually confirmed by commercial latex allergy skinprick testing or by ...

  14. Size effects of latex nanomaterials on lung inflammation in mice

    International Nuclear Information System (INIS)

    Inoue, Ken-ichiro; Takano, Hirohisa; Yanagisawa, Rie; Koike, Eiko; Shimada, Akinori

    2009-01-01

    Effects of nano-sized materials (nanomaterials) on sensitive population have not been well elucidated. This study examined the effects of pulmonary exposure to (latex) nanomaterials on lung inflammation related to lipopolysaccharide (LPS) or allergen in mice, especially in terms of their size-dependency. In protocol 1, ICR male mice were divided into 8 experimental groups that intratracheally received a single exposure to vehicle, latex nanomaterials (250 μg/animal) with three sizes (25, 50, and 100 nm), LPS (75 μg/animal), or LPS plus latex nanomaterials. In protocol 2, ICR male mice were divided into 8 experimental groups that intratracheally received repeated exposure to vehicle, latex nanomaterials (100 μg/animal), allergen (ovalbumin: OVA; 1 μg/animal), or allergen plus latex nanomaterials. In protocol 1, latex nanomaterials with all sizes exacerbated lung inflammation elicited by LPS, showing an overall trend of amplified lung expressions of proinflammatory cytokines. Furthermore, LPS plus nanomaterials, especially with size less than 50 nm, significantly elevated circulatory levels of fibrinogen, macrophage chemoattractant protein-1, and keratinocyte-derived chemoattractant, and von Willebrand factor as compared with LPS alone. The enhancement tended overall to be greater with the smaller nanomaterials than with the larger ones. In protocol 2, latex nanomaterials with all sizes did not significantly enhance the pathophysiology of allergic asthma, characterized by eosinophilic lung inflammation and Igs production, although latex nanomaterials with less than 50 nm significantly induced/enhanced neutrophilic lung inflammation. These results suggest that latex nanomaterials differentially affect two types of (innate and adaptive immunity-dominant) lung inflammation

  15. Ultrafine particles in concrete: Influence of ultrafine particles on concrete properties and application to concrete mix design

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, Carsten

    2010-07-01

    In this work, the influence of ultrafine particles on concrete properties was investigated. In the context of this work, ultrafine particles (reactive and inert materials) are particles finer than cement. Due to the development of effective superplasticizers, the incorporation of ultrafine particles in concrete is nowadays possible. Different minerals, usually considered inert, were tested. These minerals were also used in combination with reactive silica fume. The modified Andreassen model was used to optimise the particle size distribution and thus the packing density of the complete mix composition. Heat of hydration, compressive strength, shrinkage, frost resistance and the microstructure were investigated.The influence of different ultrafine inert materials on the cement hydration was investigated. The results show that most of the minerals have an accelerating effect. They provide nucleation sites for hydration products and contribute in that way to a faster dissolution of cement grains. Minerals containing calcium were found to influence the early stage of hydration as well. These minerals shortened the dormant period of the cement hydration, the effect is known from limestone filler in self-compacting concrete. In a first test series on concrete, different ultrafine inert particles were used to replace cement. That was done in several ways; with constant water content or constant w/c. The results from this test series show that the best effect is achieved when cement is replaced by suitable ultrafines while the w/c is kept constant. In doing so, the compressive strength can be increased and shrinkage can be reduced. The microstructure is improved and becomes denser with improved packing at microlevel. Efficiency factors (k values) for the ultrafine inert materials were calculated from the compressive strength results. The k values are strongly dependent on the mode of cement replacement, fineness and type of the replacement material and curing time. Drying

  16. Syntheses of crosslinked latex nanoparticles using differential microemulsion polymerization

    Science.gov (United States)

    Hassmoro, N. F.; Rusop, M.; Abdullah, S.

    2013-06-01

    The differential microemulsion polymerization was used to synthesize latex nanoparticles. In this paper, 1, 3-butylene glycol dimethacrylate (1, 3-BGDMA) was used as a crosslinker respectively 1-5 weight% of monomer total. Butyl acrylate (BA), butyl methacrylate (BMA), and methacrylic acid (MAA) was used as the monomer. The thin film of latex nanoparticles were prepared by using spin coating method and have been dried at 100°C for 5 minutes. The amount of the crosslinker added in the polymerization was optimized and we found that the particle sizes fall in the range of 30-60 nm. The structural morphology of the uncrosslinked latex represented the most homogeneous image compared to the crosslinked latex. The effect of the amount of crosslinker on the particle sizes investigated by the Zeta-sizer Nano series while Atomic Force microscopy (AFM) was used to study the structural properties of latex nanoparticles.

  17. Syntheses of crosslinked latex nanoparticles using differential microemulsion polymerization

    International Nuclear Information System (INIS)

    Hassmoro, N F; Abdullah, S; Rusop, M

    2013-01-01

    The differential microemulsion polymerization was used to synthesize latex nanoparticles. In this paper, 1, 3-butylene glycol dimethacrylate (1, 3-BGDMA) was used as a crosslinker respectively 1–5 weight% of monomer total. Butyl acrylate (BA), butyl methacrylate (BMA), and methacrylic acid (MAA) was used as the monomer. The thin film of latex nanoparticles were prepared by using spin coating method and have been dried at 100°C for 5 minutes. The amount of the crosslinker added in the polymerization was optimized and we found that the particle sizes fall in the range of 30–60 nm. The structural morphology of the uncrosslinked latex represented the most homogeneous image compared to the crosslinked latex. The effect of the amount of crosslinker on the particle sizes investigated by the Zeta-sizer Nano series while Atomic Force microscopy (AFM) was used to study the structural properties of latex nanoparticles.

  18. Home Healthcare Workers: How to Prevent Latex Allergies

    Science.gov (United States)

    ... can help prevent allergic reactions for both home healthcare workers and their clients. LATEX EXPOSURE REACTIONS Three ... being used). • Inform your employer and your personal healthcare professionals that you have latex allergy. • Wear a ...

  19. A new smart additive of reinforced concrete based on modified hydrotalcites: Preparation, characterization and anticorrosion applications

    NARCIS (Netherlands)

    Yang, Z.; Fischer, H.; Polder, R.

    2012-01-01

    A carbonate form of Mg-Al-hydrotalcite and its p-aminobenzoate (pAB) modified derivative (i.e.,Mg(2)Al-pAB) were synthesized and characterized by means of XRD and FT-IR. The anticorrosion behavior was evaluated based on open circuit potential (OCP) of carbon steel in simulated concrete pore solution

  20. Angiogenic activity of Synadenium umbellatum Pax latex

    Directory of Open Access Journals (Sweden)

    PR. Melo-Reis

    Full Text Available Synadenium umbellatum Pax, popularly known as "cola-nota", is a medicinal plant that grows in tropical regions. Latex of this plant is used to treat various diseases such as diabetes mellitus, Hansen´s disease, tripanosomiases, leukemia and several malignant tumors. In the present study, the angiogenic activity of S. umbellatum latex was evaluated using the chick embryo chorioallantoic membrane (CAM assay. Results showed significant increase of the vascular net (p < 0.05 compared to the negative control (H2O. The histological analysis was in accordance with the results obtained. In conclusion, our data indicate that S. umbellatum latex, under the conditions of this research, presented angiogenic effect.

  1. Enhanced protein adsorption and patterning on nanostructured latex-coated paper.

    Science.gov (United States)

    Juvonen, Helka; Määttänen, Anni; Ihalainen, Petri; Viitala, Tapani; Sarfraz, Jawad; Peltonen, Jouko

    2014-06-01

    Specific interactions of extracellular matrix proteins with cells and their adhesion to the substrate are important for cell growth. A nanopatterned latex-coated paper substrate previously shown to be an excellent substrate for cell adhesion and 2D growth was studied for directed immobilization of proteins. The nanostructured latex surface was formed by short-wavelength IR irradiation of a two-component latex coating consisting of a hydrophilic film-forming styrene butadiene acrylonitrile copolymer and hydrophobic polystyrene particles. The hydrophobic regions of the IR-treated latex coating showed strong adhesion of bovine serum albumin (cell repelling protein), fibronectin (cell adhesive protein) and streptavidin. Opposite to the IR-treated surface, fibronectin and streptavidin had a poor affinity toward the untreated pristine latex coating. Detailed characterization of the physicochemical surface properties of the latex-coated substrates revealed that the observed differences in protein affinity were mainly due to the presence or absence of the protein repelling polar and charged surface groups. The protein adsorption was assisted by hydrophobic (dehydration) interactions. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. Shear Behavior Models of Steel Fiber Reinforced Concrete Beams Modifying Softened Truss Model Approaches.

    Science.gov (United States)

    Hwang, Jin-Ha; Lee, Deuck Hang; Ju, Hyunjin; Kim, Kang Su; Seo, Soo-Yeon; Kang, Joo-Won

    2013-10-23

    Recognizing that steel fibers can supplement the brittle tensile characteristics of concrete, many studies have been conducted on the shear performance of steel fiber reinforced concrete (SFRC) members. However, previous studies were mostly focused on the shear strength and proposed empirical shear strength equations based on their experimental results. Thus, this study attempts to estimate the strains and stresses in steel fibers by considering the detailed characteristics of steel fibers in SFRC members, from which more accurate estimation on the shear behavior and strength of SFRC members is possible, and the failure mode of steel fibers can be also identified. Four shear behavior models for SFRC members have been proposed, which have been modified from the softened truss models for reinforced concrete members, and they can estimate the contribution of steel fibers to the total shear strength of the SFRC member. The performances of all the models proposed in this study were also evaluated by a large number of test results. The contribution of steel fibers to the shear strength varied from 5% to 50% according to their amount, and the most optimized volume fraction of steel fibers was estimated as 1%-1.5%, in terms of shear performance.

  3. Self-compacting concrete mixtures for road BUILDING

    Directory of Open Access Journals (Sweden)

    Tran Tuan My

    2012-10-01

    Therefore, effective concrete road pavements require self-compacting though non-segregating concrete mixtures to comply with the pre-set values of their properties, namely, bending and compressive strength, corrosion resistance, freeze resistance, etc. Acting in cooperation with Department of Technology of Binders and Concretes of MSUCE, NIIMosstroy developed and examined a self-compacting cast concrete mixture designated for durable monolithic road pavements. The composition in question was generated by adding a multi-component modifier into the mix. The modifier was composed of a hyperplasticiser, active (structureless fine and crystalline silica, and a concrete hardening control agent.

  4. Durability of crystalline phase in concrete microstructure modified by the mineral powders: evaluation by nanoindentation tests

    Directory of Open Access Journals (Sweden)

    Rajczakowska Magdalena

    2016-03-01

    Full Text Available This paper presents the nanoindentation investigation of the evolution of concrete microstructure modified by the Internal Crystallization Technology mineral powders. The samples under study were retrieved from a fragment of a circular concrete lining of the vertical mine shaft at a depth of approximately 1,000 m. Due to the aggressive environment and exposure to contaminated water, the internal surface of the structure was deteriorated, decreasing its strength significantly. The mineral powders were applied directly on the surface lining. The specimens were investigated one month, three months and one year after the application of the aforementioned substance in order to verify the time dependence of the strengthening processes and durability of the crystalline phase. The microstructural changes of concrete were assessed with the use of nanoindentation technique. The testing procedure involved including the previously cut specimens in the epoxy resin and grinding and polishing in order to reduce the surface roughness. As a result of the nanoindentation tests the hardness as well as Young’s modulus of the material were evaluated. The results were then compared and statistically analyzed. As a consequence, the disintegration time of the crystalline network in the pores of concrete was identified.

  5. prediction of concrete mix cost using modified regression theory

    African Journals Online (AJOL)

    Kambula

    2013-07-02

    Jul 2, 2013 ... one can predict the cost per cubic meter of concrete if the mix ratios are given. The model can also give possible mix ratios for a specified cost. Statistical tool was used to verify the adequacy of this model. The concrete cost analysis is based on the current market prices of concrete constituent materials.

  6. Triterpenoid biosynthesis in Euphorbia lathyris latex

    International Nuclear Information System (INIS)

    Hawkins, D.R.

    1987-11-01

    The structures of triterpenols, not previously been known, from Euphorbia lathyris latex are reported. A method for quantifying very small amounts of these compounds was developed. Concerning the biochemistry of the latex, no exogenous cofactors were required for the biosynthesis and the addition of compounds such as NADPAH and ATP do not stimulate the biosynthesis. The addition of DTE or a similar anti-oxidant was found to help reduce the oxidation of the latex, thus increasing the length of time that the latex remains active. The requirement of a divalent cation and the preference for Mn in the pellet was observed. The effect of several inhibitors on the biosynthesis of the triterpenoids was examined. Mevinolin was found to inhibit the biosynthesis of the triterpenoids from acetate, but not mevalonate. A dixon plot of the inhibition of acetate incorporation showed an I 50 concentration of 3.2 μM. Fenpropimorph was found to have little or no effect on the biosynthesis. Tridemorph was found to inhibit the biosynthesis of all of the triterpenoids with an I 50 of 4 μM. It was also observed that the cyclopropyl containing triterpenols, cycloartenol and 24-methylenecycloartenol were inhibited much more strongly than those containing an 8-9 double bond, lanosterol and 24-methylenelanosterol. The evidence indicates, but does not definetely prove, that lanosterol and 24-methylenelanosterol are not made from cycloartenol and 24-methylenecycloartenol via a ring-opening enzyme such as cycloeucalenol-obtusifoliol isomerase. The possibilty that cycloartenol is made via lanosterol was investigated by synthesizing 4-R-4- 3 H-mevalonic acid and incubating latex with a mixture of this and 14 C-mevalonic acid. From the 3 H/ 14 C ratio it was shown that cycloartenol and 24-methylenecycloartenol are not made via an intermediate containing as 8-9 double bond. 88 refs., 15 figs., 30 tabs

  7. PS-HEMA latex fractionation by sedimentation and colloidal crystallization

    Directory of Open Access Journals (Sweden)

    Cardoso André H.

    1999-01-01

    Full Text Available A poly(styrene-co-hydroxyethylmethacrylate latex underwent sedimentation under gravity followed by an spontaneous and extensive colloidal crystallization. It was then fractionated in three visually distinguishable layers. Latex aliquots layers were sampled at different heigths and the particles were characterized by PCS, microelectrophoresis, infrared spectra and analytical electron microscopy. The major fraction was opalescent and contained the colloidal crystals settled in the bottom of the liquid. Two other latex fractions were obtained, which differed in their chemical compositions, particle sizes and topochemical features from the self-arraying particles. Macrocrystallization of the fractionated latex yielded high quality crystals with a low frequency of defects, which confirms that particle chemical homogeneity is an important factor for particle self-arraying.

  8. Synthesis and characterization of fluorinated polyacrylate latex emulsified with novel surfactants.

    Science.gov (United States)

    Zhang, Cuifeng; Xu, Tingting; Bao, Zhongbin; Chen, Lijun

    2017-01-01

    The fluorinated polyacrylate latex were successfully prepared with semi- continuous seeded emulsion polymerization of butyl acrylate (BA), methyl methacrylate (MMA) and hexafluorobutyl methacrylate (HFMA) which was initiated with potassium persulfate (KPS) initiator and emulsified with the novel mixed surfactants of sodium lauryl glutamate (SLG) and alkylphenol ethoxylates (OP-10). The structure of the resultant latex was confirmed by Fourier transform infrared spectroscopy (FTIR). The particle size of the latex was measured by Zetatrac dynamic light scattering detector. The film of latex was tested by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and contact angle (CA). The optimum conditions of preparing the novel fluorinated polyacrylate latex are optimized and the results are as follows: the amount of emulsifiers is 4.0%; mass ratio of SLG to OP-10 is 1:1, the amount of the initiator is 0.6%. The mass ratio of MMA to BA is 1:1 and the amount of HFMA is 7.0%. In this case, the conversion is high and the polymerization stability is good. In addition, the water resistance and thermal properties of the latex films were improved significantly in comparison with the film of the latex prepared without the fluorinated monomer.

  9. Plant latex: a promising antifungal agent for post harvest disease control.

    Science.gov (United States)

    Sibi, G; Wadhavan, Rashmi; Singh, Sneha; Shukla, Abhilasha; Dhananjaya, K; Ravikumar, K R; Mallesha, H

    2013-12-01

    Bioactive compounds from plant latex are potential source of antifungic against post harvest pathogens. Latex from a total of seven plant species was investigated for its phytochemical and antifungal properties. Six fungi namely Aspergillus fumigatus, A. niger, A. terreus, F. solani, P. digitatum and R. arrhizus were isolated from infected fruits and vegetables and tested against various solvent extracts of latex. Analysis of latex extracts with phytochemical tests showed the presence of alkaloids, flavonoids, glycosides, phenols, saponins, steroids, tannins and terpenoids. Antifungal assay revealed the potential inhibitory activity of petroleum ether extracts against the postharvest fungal isolates. Various degree of sensitivity was observed irrespective of plant species studied with A. terreus and P. digitatum as the most susceptible ones. F. solani and A. fumigatus were moderately sensitive to the latex extracts tested. Among the plants, latex of Thevetia peruviana (75.2%) and Artocarpus heterophyllus (64.8%) were having potential antifungal activity against the isolates followed by Manilkara zapota (51.1%). In conclusion, use of plant latex makes interest to control postharvest fungal diseases and is fitting well with the concept of safety for human health and environment.

  10. Drying of latex films and coatings: Reconsidering the fundamental mechanisms

    DEFF Research Database (Denmark)

    Kiil, Søren

    2006-01-01

    The two existing theories describing drying of latex films or coatings are reconsidered. Subsequently, a novel mathematical drying model is presented, the simulations of which can match and explain experimental drying rate data of two previous investigations with latex films. In contrast to previ......The two existing theories describing drying of latex films or coatings are reconsidered. Subsequently, a novel mathematical drying model is presented, the simulations of which can match and explain experimental drying rate data of two previous investigations with latex films. In contrast...... to previous model studies, but in agreement with observations, simulations suggest that during the falling rate period of the drying process of a latex film, a porous skin of partly coalesced latex particles is indeed formed, which limits transport of water vapour from the receding air-liquid interphase...... to the surface of the film. The value of the effective diffusion coefficient of water vapour in the dry and partly coalesced layer (7 x 10(-7) m(2)/s at 19-24 degrees C), the adjustable parameter of the model for the falling rate period, was found to be independent of initial wet film thickness (89-1322 mu m...

  11. Radiation response of Philippine natural rubber latex

    International Nuclear Information System (INIS)

    Dela Rosa, A.M.; Abad, L.V.; Ana-Relleve, L.S.; Tranquilan-Aranilla, C.; Pascual, C.L.

    1998-01-01

    Our earlier work has shown that the natural rubber latex (NRL) produced and processed in the Philippines is suited for radiation vulcanization. The cast films from NRL with 50% TSC exhibited maximum tensile strengths of 25-32 MPa at 15 kGy, which is the vulcanization dose or Dv. In the manufacture of dipped NRL products, certain specifications such as %TSC, protein content and tensile properties, must be met to ensure an acceptable product. For radiation vulcanization of natural rubber latex (RVNRL) to be accepted as an alternative process, it must also meet the requirements. Thus, this paper presents additional data on the radiation response of local NRL at different total solids contents (TSC), leachable proteins from NRL films as a function of dose, and the thermal activities of irradiated natural rubber latex (INRL). Different formulations of NRL showed varying tolerances to nBA. Data showed that as %TSC increases, the maximum concentration of nBA that can be added without affecting the stability of the latex decreases. The Dv increases as the %TSC increases and the nBA content decreases. This difference in response may be attributed to a lower concentration of nBA in formulations with higher %TSC. These data indicate that the parameters in the radiation treatment will be dictated by the intended applications of INRL. The thermogravimetric data showed greater stability of INRL to thermal oxidation relative to the unirradiated NRL, which correlates directly with the tensile properties of the INRL. A radiation dose of 10 kGy increased the amount of proteins leached from cast latex films. The amount of extractable proteins did not increase significantly at higher doses. The SDS PAGE analysis of the extractable proteins from unirradiated latex film showed distinct bands. An additional band at 60 Kda appeared at 10 kGy. All these bands became diffuse at higher doses, indicating the radiolysis of the proteins

  12. A Reappraisal of Online Mathematics Teaching Using LaTeX

    Directory of Open Access Journals (Sweden)

    Eamon Costello

    2009-12-01

    Full Text Available The mathematics language LaTeX is often seen outside of academic circles as a legacy technology that is awkward to use. MathML - a verbose language designed for data-exchange, and to be written and understood by machines - is sometimes by contrast seen as something that will aid online mathematics and lack of browser support for it bemoaned. However LaTeX can already do many of the things that MathML might promise. LaTeX is here proposed as a language from which small fragments, with concise syntax, can be used by people to easily create and share mathematical expressions online. The capability to embed fragments of LaTeX code in online discussions is described here and its impact on a group of educators and learners evaluated. Here LaTeX is posited as a useful tool for facilitating asynchronous, online, collaborative learning of mathematics.

  13. Laboratory Performance Evaluation of High Modulus Asphalt Concrete Modified with Different Additives

    Directory of Open Access Journals (Sweden)

    Peng Li

    2017-01-01

    Full Text Available The objective of this study is to evaluate comprehensive performance of high modulus asphalt concrete (HMAC and propose common values for establishing evaluation system. Three gradations with different modifiers were conducted to study the high and low temperature performance, shearing behavior, and water stability. The laboratory tests for HMAC included static and dynamic modulus tests, rutting test, uniaxial penetration test, bending test, and immersion Marshall test. Dynamic modulus test results showed that modifier can improve the static modulus and the improvements were remarkable at higher temperature. Moreover, modulus of HMAC-20 was better than those of HMAC-16 and HMAC-25. The results of performance test indicated that HMAC has good performance to resist high temperature rutting, and the resistances of the HMAC-20 and HMAC-25 against rutting were better than that of HMAC-16. Then, the common values of dynamic stability were recommended. Furthermore, common values of HMAC performance were established based on pavement performance tests.

  14. Antibacterial activity of the latex of Argemone ochroleuca Sweet

    International Nuclear Information System (INIS)

    Saad A. Alamri; Mahmoud F. Moustafa

    2010-01-01

    To investigate the antibacterial effect of the crude latex of Argemone ochroleuca (A. ochroleuca) as antibacterial potential against a range of human pathogenic bacteria. This study was carried out at King Khalid University, Abha, Kingdom of Saudi Arabia from January to March 2010. Seventeen ml of fresh latex from A. ochroleuca Sweet was collected, and the antibacterial activity of crude and diluted latex were examined using one ml of standardized inoculum suspension, and using the agar diffusion method test against Bacillus subtilis, Enterobacter aerogenes, Micrococcus luteus, Escherichia coli, and Staphylococcus aureus. All inoculated plates were incubated aerobically at 290C for 48 hours. The diameter of the zones of inhibition was measured to the nearest mm. The crude latex of A. ochroleuca exhibited a potent antibacterial effect on all bacterial strains examined. The zones of inhibition against the tested bacteria were found in the range of 9.30 - 40.3 mm along with their respective minimum inhibitory concentration values 100 ul/ml. The observable inhibition on selected bacteria by latex of A. ochroleuca makes it a promising alternative as a potential source of natural antibacterial (Author).

  15. Thrombin like activity of Asclepias curassavica L. latex: action of cysteine proteases.

    Science.gov (United States)

    Shivaprasad, H V; Rajesh, R; Nanda, B L; Dharmappa, K K; Vishwanath, B S

    2009-05-04

    To validate the scientific basis of plant latex to stop bleeding on fresh cuts. Cysteine protease(s) from Asclepias curassavica (Asclepiadaceae) plant latex was assessed for pro-coagulant and thrombin like activities. A waxy material from the latex of Asclepias curassavica latex was removed by freezing and thawing. The resulted latex enzyme fraction was assayed for proteolytic activity using denatured casein as substrate. Its coagulant activity and thrombin like activity were determined using citrated plasma and pure fibrinogen, respectively. Inhibition studies were performed using specific protease inhibitors to know the type of protease. The latex enzyme fraction exhibited strong proteolytic activity when compared to trypsin and exerted pro-coagulant action by reducing plasma clotting time from 195 to 58 s whereas trypsin reduced clotting time marginally from 195 to 155 s. The pro-coagulant activity of this enzyme fraction was exerted by selectively hydrolyzing A alpha and B beta subunits of fibrinogen to form fibrin clot when pure fibrinogen was used as substrate as assessed by fibrinogen-agarose plate method and fibrinogen polymerization assay. Trypsin failed to induce any fibrin clot under similar conditions. The electrophoretic pattern of latex enzyme fraction-induced fibrin clot was very much similar to that of thrombin-induced fibrin clot and mimic thrombin like action. The proteolytic activity including thrombin like activity of Asclepias curassavica latex enzyme fraction was completely inhibited by iodoaceticacid (IAA). Cysteine proteases from Asclepias curassavica latex exhibited strong pro-coagulant action and were found to be specific in its action (Thrombin like). This could be the basis for the use of plant latex in pharmacological applications that justify their use as folk medicine.

  16. Shear Behavior Models of Steel Fiber Reinforced Concrete Beams Modifying Softened Truss Model Approaches

    Directory of Open Access Journals (Sweden)

    Joo-Won Kang

    2013-10-01

    Full Text Available Recognizing that steel fibers can supplement the brittle tensile characteristics of concrete, many studies have been conducted on the shear performance of steel fiber reinforced concrete (SFRC members. However, previous studies were mostly focused on the shear strength and proposed empirical shear strength equations based on their experimental results. Thus, this study attempts to estimate the strains and stresses in steel fibers by considering the detailed characteristics of steel fibers in SFRC members, from which more accurate estimation on the shear behavior and strength of SFRC members is possible, and the failure mode of steel fibers can be also identified. Four shear behavior models for SFRC members have been proposed, which have been modified from the softened truss models for reinforced concrete members, and they can estimate the contribution of steel fibers to the total shear strength of the SFRC member. The performances of all the models proposed in this study were also evaluated by a large number of test results. The contribution of steel fibers to the shear strength varied from 5% to 50% according to their amount, and the most optimized volume fraction of steel fibers was estimated as 1%–1.5%, in terms of shear performance.

  17. Parameters of Concrete Modified with Glass Meal and Chalcedonite Dust

    Science.gov (United States)

    Kotwa, Anna

    2017-10-01

    Additives used for production of concrete mixtures affect the rheological properties and parameters of hardened concrete, including compressive strength, water resistance, durability and shrinkage of hardened concrete. By their application, the use of cement and production costs may be reduced. The scheduled program of laboratory tests included preparation of six batches of concrete mixtures with addition of glass meal and / or chalcedonite dust. Mineral dust is a waste product obtained from crushed aggregate mining, with grain size below 0,063μm. The main ingredient of chalcedonite dust is silica. Glass meal used in the study is a material with very fine grain size, less than 65μm. This particle size is present in 60% - 90% of the sample. Additives were used to replace cement in concrete mixes in an amount of 15% and 25%. The amount of aggregate was left unchanged. The study used Portland cement CEM I 42.5R. Concrete mixes were prepared with a constant rate w / s = 0.4. The aim of the study was to identify the effect of the addition of chalcedonite dust and / or glass meal on the parameters of hardened concrete, i.e. compressive strength, water absorption and capillarity. Additives used in the laboratory tests significantly affect the compressive strength. The largest decrease in compressive strength of concrete samples was recorded for samples with 50% substitutes of cement additives. This decrease is 34.35%. The smallest decrease in compressive strength was noted in concrete with the addition of 15% of chalcedonite dust or 15% glass meal, it amounts to an average of 15%. The study of absorption shows that all concrete with the addition of chalcedonite dust and glass meal gained a percentage weight increase between 2.7 ÷ 3.1% for the test batches. This is a very good result, which is probably due to grout sealing. In capillary action for the test batches, the percentage weight gains of samples ranges from 4.6% to 5.1%. However, the reference concrete obtained

  18. Corrosion of Modified Concrete with Sugar Cane Bagasse Ash

    Directory of Open Access Journals (Sweden)

    R. E. Núñez-Jaquez

    2012-01-01

    Full Text Available Concrete is a porous material and the ingress of water, oxygen, and aggressive ions, such as chlorides, can cause the passive layer on reinforced steel to break down. Additives, such as fly ash, microsilica, rice husk ash, and cane sugar bagasse ash, have a size breakdown that allows the reduction of concrete pore size and, consequently, may reduce the corrosion process. The objective of this work is to determine the corrosion rate of steel in reinforced concrete by the addition of 20% sugar cane bagasse ash by weight of cement. Six prismatic specimens (7×7×10 cm with an embedded steel rod were prepared. Three contained 20% sugar cane bagasse ash by weight of cement and the other three did not. All specimens were placed in a 3.5% NaCl solution and the corrosion rate was determined using polarization resistance. The results showed that reinforced concrete containing sugar cane bagasse ash has the lowest corrosion rates in comparison to reinforced concrete without the additive.

  19. Triterpenoid biosynthesis in Euphorbia lathyris latex

    Energy Technology Data Exchange (ETDEWEB)

    Hawkins, D.R.

    1987-11-01

    The structures of triterpenols, not previously been known, from Euphorbia lathyris latex are reported. A method for quantifying very small amounts of these compounds was developed. Concerning the biochemistry of the latex, no exogenous cofactors were required for the biosynthesis and the addition of compounds such as NADPAH and ATP do not stimulate the biosynthesis. The addition of DTE or a similar anti-oxidant was found to help reduce the oxidation of the latex, thus increasing the length of time that the latex remains active. The requirement of a divalent cation and the preference for Mn in the pellet was observed. The effect of several inhibitors on the biosynthesis of the triterpenoids was examined. Mevinolin was found to inhibit the biosynthesis of the triterpenoids from acetate, but not mevalonate. A dixon plot of the inhibition of acetate incorporation showed an I/sub 50/ concentration of 3.2 ..mu..M. Fenpropimorph was found to have little or no effect on the biosynthesis. Tridemorph was found to inhibit the biosynthesis of all of the triterpenoids with an I/sub 50/ of 4 ..mu..M. It was also observed that the cyclopropyl containing triterpenols, cycloartenol and 24-methylenecycloartenol were inhibited much more strongly than those containing an 8-9 double bond, lanosterol and 24-methylenelanosterol. The evidence indicates, but does not definetely prove, that lanosterol and 24-methylenelanosterol are not made from cycloartenol and 24-methylenecycloartenol via a ring-opening enzyme such as cycloeucalenol-obtusifoliol isomerase. The possibilty that cycloartenol is made via lanosterol was investigated by synthesizing 4-R-4-/sup 3/H-mevalonic acid and incubating latex with a mixture of this and /sup 14/C-mevalonic acid. From the /sup 3/H//sup 14/C ratio it was shown that cycloartenol and 24-methylenecycloartenol are not made via an intermediate containing as 8-9 double bond. 88 refs., 15 figs., 30 tabs.

  20. The methods of receiving coal water suspension and its use as the modifying additive in concrete

    Science.gov (United States)

    Buyantuyev, S. L.; Urkhanova, L. A.; Lkhasaranov, S. A.; Stebenkova, Y. Y.; Khmelev, A. B.; Kondratenko, A. S.

    2017-01-01

    Results of research of the coal water suspension (CWS) from a cake received in the electrodigit ways in the fluid environment and gas are given in article and also the possibilities of its use as the modifying additive in concrete are considered. Use of a coal cake is perspective as it is a withdrawal of the coal and concentrating enterprises and has extremely low cost. Methods of receiving CWS and possibility of formation of carbon nanomaterials (CNM) are given in their structure. Research and the analysis of a microstructure of a surface of exemplars before electrodigit processing, their element structure, dependence of durability of a cement stone on a look and quantity of an additive of CWS is conducted. For modification of cement the carbon nanomaterials received from the following exemplars of water coal suspensions were used: foams from a cake from a scrubber of the plasma modular reactor, coal water suspension from a cake from electrodigit installation. The product which can find further application for a power engineering as fuel for combustion, and also in structural materials science, in particular, as the modifying additive in concrete allows to receive these methods.

  1. Properties of concrete modified with waste Low Density Polyethylene and saw dust ash

    Science.gov (United States)

    Srimanikandan, P.; Sreenath, S.

    2017-07-01

    The increase in industrialization creates need for disposal of large quantity of by-products. To overcome the difficulty of disposal, these by-products can be used as a replacement for raw material. In this concern, non-conventional industrial wastes such as plastic bags, PET bottles, pulverized waste Low Density Polyethylene (LDPE) and biological waste such as saw-dust ash, coconut coir were used as a replacement in concrete. In this project, saw-dust ash and pulverized waste LDPE were introduced as the partial replacement for cement and fine aggregates respectively. 0%, 5%, 10%, 15% and 20% of sand by volume was replaced with LDPE and 0%, 1%, 3%, 5% and 10% of cement by volume was replaced with saw dust ash. Standard cube, cylinder and prism specimens were cast to assess the compressive strength, split tensile strength and flexural strength of modified concrete after 28 days of curing. Optimum percentage of replacement was found by comparing the test results. The mix with 5% of LDPE and 3% of saw dust ash showed a better result among the other mixes.

  2. Alergia látex-fruta Latex-fruit allergy

    Directory of Open Access Journals (Sweden)

    Flávia Andréia MARIN

    2002-01-01

    Full Text Available O látex está sendo considerado o alergênico do ano 2000, tendo em vista que inúmeros indivíduos, principalmente profissionais da área de saúde e pacientes submetidos a várias intervenções diagnósticas e terapêuticas, estão freqüentemente expostos aos alérgenos do látex, presentes em produtos de borracha natural. As manifestações clínicas conseqüentes às reações alérgicas de hipersensibilidade imediata vão desde rinite, urticária, conjuntivite, angioedema, asma, até anafilaxia. Estudos recentes estão demonstrando que pacientes alérgicos ao látex desenvolvem concomitantemente sensibilização a certos alimentos de origem vegetal, especialmente frutas como papaia, figo, banana, abacate, kiwi, pêssego, abacaxi, melão e castanha, acreditando-se numa provável ocorrência de reações cruzadas entre os alérgenos do látex e destas frutas. Faz-se, então, uma revisão sobre a alergia ao látex, em particular sobre os grupos de risco, incluindo a presença de reatividade cruzada entre o látex e as frutas.The latex is being considered the allergenic agent of the year 2000, taking into account that several individuals, mainly health care professionals, and patients who had undergone many diagnostic and therapeutic interventions, are frequently exposed to latex allergens, which are present in natural rubber latex products. The clinical manifestations, derived from allergic reactions of immediate hypersensitivity vary from since rhinitis, conjunctivitis, urticaria, angioedema, asthma, to anaphylaxis. Recent researches are demonstrating that patients allergic to latex develop concomitantly sensitization to certain vegetable foods, especially fruits like papaya, fig, banana, avocado, kiwi, peach, pineapple, melon and chestnut, and a probable occurrence of cross reaction between allergens of latex and of these fruits is believed. A review is made about latex allergy, in particular about risk groups, including the presence of

  3. HIGH-QUALITY ORNAMENTAL FINE CONCRETES MODIFIED BY NANOPARTICLES OF TITANIUM DIOXIDE

    Directory of Open Access Journals (Sweden)

    Bazhenov Yuriy Mikhaylovich

    2012-10-01

    Full Text Available Ultrasonic method of generation of a stable suspension of nano-particles of titanium dioxide and the strengthening properties of the ornamental fine concrete that contains cement binders with a nano-dispersed additive constitute the subject of the research covered by the authors. Nanoparticles react with the basic chemical elements that compose the concrete and act as crystallization centres. Therefore, the concrete porosity is reduced, while physical and technology-related properties of the ornamental fine concrete are improved. The authors have proven that the application of the nano-dispersed additive that contains titanium dioxide influences the processes of the structure formation in respect of fine ornamental concretes and improves the strength, as well as the water and cold resistance of fine concretes. The improvement is attributed to the dense concrete structure and strong adhesion between cement grains and between the cement and the aggregate. This conclusion is based on the data obtained through the employment of an electronic microscope used to identify the porosity of fine concretes.

  4. Radiation vulcanization of natural rubber latex sensitized with commercial gases

    International Nuclear Information System (INIS)

    Chirinos, H.; Lugao, A.

    2002-01-01

    The industrial activities using natural rubber latex are fully compatible with rural areas in Amazon and other places in Brazil, as well as in other tropical countries. However the classical sulfur vulcanization presents many occupational problems for the workers in rural areas. Radiation vulcanization of natural rubber latex is a much more friendly process as sulfur compounds are not needed for crosslinking, although chemicals as acrylate monomers, particularly multifunctional acrylates are still used as sensitizers for radiation processes. Two commercial gases, acetylene and butadiene, were selected as sensitizers for the radiation vulcanization of natural rubber latex instead of acrylates. These gases accelerate the crosslinking rates of the cure process and lower the radiation dose required to achieve vulcanization of natural rubber latex and improve the mechanical properties to reduce the tackiness of rubber goods. (author)

  5. Radiation vulcanization of natural rubber latex sensitized with commercial gases

    Energy Technology Data Exchange (ETDEWEB)

    Chirinos, H.; Lugao, A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

    2002-07-01

    The industrial activities using natural rubber latex are fully compatible with rural areas in Amazon and other places in Brazil, as well as in other tropical countries. However the classical sulfur vulcanization presents many occupational problems for the workers in rural areas. Radiation vulcanization of natural rubber latex is a much more friendly process as sulfur compounds are not needed for crosslinking, although chemicals as acrylate monomers, particularly multifunctional acrylates are still used as sensitizers for radiation processes. Two commercial gases, acetylene and butadiene, were selected as sensitizers for the radiation vulcanization of natural rubber latex instead of acrylates. These gases accelerate the crosslinking rates of the cure process and lower the radiation dose required to achieve vulcanization of natural rubber latex and improve the mechanical properties to reduce the tackiness of rubber goods. (author)

  6. Preparation of irradiated natural rubber latex-styrene copolymer for electrical gloves

    International Nuclear Information System (INIS)

    Made Sumarti Kardha

    2010-01-01

    Research on irradiated natural rubber latex-styrene copolymer to prepare electrical glove have been done. Vulcanization of natural rubber latex (NRL) was done by mixing 2 phr (per hundred of rubber) of normal butyl acrylate (n-BA) emulsion then irradiated with ã-ray "6"0Co at the dose of 30 kGy producing irradiated natural rubber latex (INRL). Natural rubber latex-styrene copolymers (SC) were prepared by mixing NRL and styrene monomer at styrene concentrations of 50 phr, 75 phr, 100 phr, 500 phr and irradiated at the doses of 15 kGy, 30 kGy and 45 kGy, then characterized their latex and film properties to obtain optimum SC of SC50. This optimum SC, SC50 then mixed with IRNL at the weight ratio of 0/100, 30/70, 50/50, 70/30 and 100/0, to produce irradiated natural rubber latex-styrene copolymer. The properties of copolymer rubber films made by dipping process i.e., % conversion, total solid content, latex viscosity, tensile strength, modulus 300 %, elongation at break, electrical resistance and dielectric constant were then characterized. Characterization result showed that (INRL-SC50) with 50/50 ratio irradiated at the dose of 30 kGy, have % conversion of 80.93 %, electrical resistivity of 1.73 x 10"1"4 Ohm cm and dielectric constant of 2.76 which fulfill the requirement as material for electrical gloves. (author)

  7. Antimicrobial activity of latex silver nanoparticles using Calotropis procera

    Directory of Open Access Journals (Sweden)

    Nadia Hussein Mohamed

    2014-11-01

    Conclusions: It can be concluded that serum latex of Calotropis procera was found to display strong potential for the synthesis of AgNPs as antimicrobial agents through rapid reduction of silver ions (Ag+ to Ag0. The green synthesized AgNPs were found to show higher antimicrobial efficacy than crude latex.

  8. Immune response modulation by curcumin in a latex allergy model

    Directory of Open Access Journals (Sweden)

    Raju Raghavan

    2007-01-01

    Full Text Available Abstract Background There has been a worldwide increase in allergy and asthma over the last few decades, particularly in industrially developed nations. This resulted in a renewed interest to understand the pathogenesis of allergy in recent years. The progress made in the pathogenesis of allergic disease has led to the exploration of novel alternative therapies, which include herbal medicines as well. Curcumin, present in turmeric, a frequently used spice in Asia has been shown to have anti-allergic and inflammatory potential. Methods We used a murine model of latex allergy to investigate the role of curcumin as an immunomodulator. BALB/c mice were exposed to latex allergens and developed latex allergy with a Th2 type of immune response. These animals were treated with curcumin and the immunological and inflammatory responses were evaluated. Results Animals exposed to latex showed enhanced serum IgE, latex specific IgG1, IL-4, IL-5, IL-13, eosinophils and inflammation in the lungs. Intragastric treatment of latex-sensitized mice with curcumin demonstrated a diminished Th2 response with a concurrent reduction in lung inflammation. Eosinophilia in curcumin-treated mice was markedly reduced, co-stimulatory molecule expression (CD80, CD86, and OX40L on antigen-presenting cells was decreased, and expression of MMP-9, OAT, and TSLP genes was also attenuated. Conclusion These results suggest that curcumin has potential therapeutic value for controlling allergic responses resulting from exposure to allergens.

  9. Capacitance Regression Modelling Analysis on Latex from Selected Rubber Tree Clones

    International Nuclear Information System (INIS)

    Rosli, A D; Baharudin, R; Hashim, H; Khairuzzaman, N A; Mohd Sampian, A F; Abdullah, N E; Kamaru'zzaman, M; Sulaiman, M S

    2015-01-01

    This paper investigates the capacitance regression modelling performance of latex for various rubber tree clones, namely clone 2002, 2008, 2014 and 3001. Conventionally, the rubber tree clones identification are based on observation towards tree features such as shape of leaf, trunk, branching habit and pattern of seeds texture. The former method requires expert persons and very time-consuming. Currently, there is no sensing device based on electrical properties that can be employed to measure different clones from latex samples. Hence, with a hypothesis that the dielectric constant of each clone varies, this paper discusses the development of a capacitance sensor via Capacitance Comparison Bridge (known as capacitance sensor) to measure an output voltage of different latex samples. The proposed sensor is initially tested with 30ml of latex sample prior to gradually addition of dilution water. The output voltage and capacitance obtained from the test are recorded and analyzed using Simple Linear Regression (SLR) model. This work outcome infers that latex clone of 2002 has produced the highest and reliable linear regression line with determination coefficient of 91.24%. In addition, the study also found that the capacitive elements in latex samples deteriorate if it is diluted with higher volume of water. (paper)

  10. Decontamination of latex gloves; Decontamination de gants en latex

    Energy Technology Data Exchange (ETDEWEB)

    Boutot, P; Schipfer, P; Blachere, A [Commissariat a l' Energie Atomique, Chusclan (France). Centre de Production de Plutonium de Marcoule

    1969-07-01

    Initially the latex gloves used in controlled zones were processed after use as radioactive waste. In view of the continually increasing number used, however, the persons in charge of the SPRAR have considered the possibility of decontaminating the gloves and using them again after control. The recovery installations which have been developed were initially designed rather crudely and operated irregularly; they have been progressively improved as a result of the experience acquired; today they are more really an industrial concern, equipped with automatic machinery. In 1967 it has been possible with this set-up to recover 247000 pairs of gloves, representing nearly 70 per cent of the number treated. (author) [French] Initialement, les gants de latex utilises dans les zones controlees etaient conditionnes apres emploi comme dechets radioactifs. Mais, devant l'augmentation sans cesse croissante des quantites employees, les responsables du SPRAR ont envisage leur decontamination et leur recyclage apres controles. Les installations de recuperation mises au point, de conception artisanale et fonctionnant de maniere episodique au depart, se sont progressivement ameliorees au fur et a mesure de l'experience acquise; elles revetent aujourd'hui le caractere d'une exploitation industrielle equipee de machines automatiques. En 1967, ces nouvelles installations ont permis de recuperer 247000 paires de gants, ce qui represente pres de 70 pour cent des quantites traitees. (auteur)

  11. Follow-up Study of Latex-allergic Health Care Workers in Japan

    Directory of Open Access Journals (Sweden)

    Akiko Yagami

    2006-01-01

    Conclusions: After avoiding latex products and following our educational suggestions, the patients' allergy symptoms had generally improved. This indicates that our countermeasures against latex allergy were largely successful.

  12. Morphology and film formation of poly(butyl methacrylate)-polypyrrole core-shell latex particles

    NARCIS (Netherlands)

    Huijs, F; Lang, J

    Core-shell latex particles made of a poly(butyl methacrylate) (PBMA) core and a thin polypyrrole (PPy) shell were synthesized by two-stage polymerization. In the first stage, PBMA latex particles were synthesized in a semicontinuous process by free-radical polymerization. PBMA latex particles were

  13. Latex allergies - for hospital patients

    Science.gov (United States)

    ... ency/patientinstructions/000499.htm Latex allergies - for hospital patients To use the sharing features on this page, ... ADAM Health Solutions. About MedlinePlus Site Map FAQs Customer Support Get email updates Subscribe to RSS Follow ...

  14. Installing fonts in LaTeX a user's experience

    NARCIS (Netherlands)

    Hanssen, F.T.Y.

    2003-01-01

    This paper presents a user's experience with installing fonts for use in LaTeX. It will be shown that it is not hard to make a standard Type 1 font work, if you use modern font installation software for LaTeX. All the steps necessary to install the example fonts will be shown. The example fonts used

  15. Radioactive iodine (125I) labeling of latex particles

    International Nuclear Information System (INIS)

    Parikh, G.C.; Ho, C.K.

    1977-01-01

    The invention disclosed in this application is directed towards developing a radioiodination method which is applicable to the labeling of 2.02 micrometer (μm) and 0.37 micrometer (μm) diameter polyvinyltoluene latex particles that have been used as an immunoadsorbent. More particularly the overall method includes using an oxidation-reduction chemical reaction for tagging latex particles. Two methods are described. One, the hydrochloric acid method; and two, the nitric acid method

  16. Rapid latex agglutination test for the serodiagnosis of human brucellosis

    NARCIS (Netherlands)

    Abdoel, Theresia H.; Smits, Henk L.

    2007-01-01

    We developed and evaluated a user-friendly latex agglutination assay for the serodiagnosis of human brucellosis. The assay was obtained by coating colored latex beads with Brucella lipopolysaccharides and drying of the activated beads onto white agglutination cards. Individual cards were sealed in a

  17. LOL2 and LOL5 loci control latex production by laticifer cells in Euphorbia lathyris.

    Science.gov (United States)

    Castelblanque, Lourdes; Balaguer, Begoña; Marti, Cristina; Orozco, Marianela; Vera, Pablo

    2018-06-07

    Laticifers are specialized plant cells capable of indefinite elongation that ramify extensively and are responsible for latex biosynthesis and accumulation. However, the mechanisms underlying laticifer cell differentiation, growth and production of latex remain largely unknown. In a search for mutants showing enhanced accumulation of latex we identified two LOT OF LATEX (LOL) loci in Euphorbia lathyris. lol2 and lol5 mutants show enhanced production of latex contained within laticifer cells. The recessive lol2 mutant carries increased biosynthesis of the plant hormone jasmonoyl-isoleucine (JA-Ile) and therefore establishes a genetic link between jasmonic acid (JA) signaling and latex production in laticifers. Instead, heightened production of latex in lol5 plants obeys to enhanced proliferation of laticifer cells. Phylogenetic analysis of laticifer-expressed genes in E. lathyris and in two other latex-bearing species, Euphorbia corallioides and Euphorbia palustris, allowed the identification of canonical JA responsive elements present in the gene promoter regions of laticifer marker genes. Moreover, we identified that the hormone JA functions not as a morphogen for laticifer differentiation but as a trigger for the fill out of laticifers with latex and the associated triterpenoids. The identification of LOL loci represents a further step towards the understanding of mechanisms controlling latex production in laticifer cells. No claim to original US Government works New Phytologist © 2018 New Phytologist Trust.

  18. Involvement of Ethylene in the Latex Metabolism and Tapping Panel Dryness of Hevea brasiliensis

    Science.gov (United States)

    Putranto, Riza-Arief; Herlinawati, Eva; Rio, Maryannick; Leclercq, Julie; Piyatrakul, Piyanuch; Gohet, Eric; Sanier, Christine; Oktavia, Fetrina; Pirrello, Julien; Kuswanhadi; Montoro, Pascal

    2015-01-01

    Ethephon, an ethylene releaser, is used to stimulate latex production in Hevea brasiliensis. Ethylene induces many functions in latex cells including the production of reactive oxygen species (ROS). The accumulation of ROS is responsible for the coagulation of rubber particles in latex cells, resulting in the partial or complete stoppage of latex flow. This study set out to assess biochemical and histological changes as well as changes in gene expression in latex and phloem tissues from trees grown under various harvesting systems. The Tapping Panel Dryness (TPD) susceptibility of Hevea clones was found to be related to some biochemical parameters, such as low sucrose and high inorganic phosphorus contents. A high tapping frequency and ethephon stimulation induced early TPD occurrence in a high latex metabolism clone and late occurrence in a low latex metabolism clone. TPD-affected trees had smaller number of laticifer vessels compared to healthy trees, suggesting a modification of cambial activity. The differential transcript abundance was observed for twenty-seven candidate genes related to TPD occurrence in latex and phloem tissues for ROS-scavenging, ethylene biosynthesis and signalling genes. The predicted function for some Ethylene Response Factor genes suggested that these candidate genes should play an important role in regulating susceptibility to TPD. PMID:26247941

  19. Allergenicity of latex rubber products used in South African dental ...

    African Journals Online (AJOL)

    Fourteen latex examination gloves (powdered and non-powdered) and five dental rubber dams, representing 6 brands, from five dental academic institutions were analysed for latex allergens and total protein. Total protein content was determined using the BioRad DC protein assay kit and natural rubber allergen levels ...

  20. Comparing the level of dexterity offered by latex and nitrile SafeSkin gloves.

    Science.gov (United States)

    Sawyer, Jo; Bennett, Allan

    2006-04-01

    An increase in the occurrence of latex allergy has been concurrent with the increasing use of latex gloves by laboratory and healthcare workers. In recent years nitrile gloves have been used to replace latex gloves to prevent latex allergy. Nitrile gloves offer a comparable level of protection against chemical and biological agents and are more puncture resistant. However, if manual dexterity is compromised by nitrile gloves to a greater degree than latex then this may increase the risk of sharps injuries. The Purdue pegboard test, which measures both gross and fine finger dexterity, was used to test the dexterity levels of two glove types used at HPA CEPR; Kimberly-Clark SafeSkin nitrile and latex laboratory gloves. There was a statistically significant 8.6% increase in fine finger dexterity provided by latex compared with nitrile SafeSkin laboratory gloves but no difference in gross dexterity between the glove types. There was no significant relationship between glove dexterity and age or gender. The selection of glove size was influenced by the digit length of participants. Moreover, those with longer, thinner fingers appeared to have an advantage when using nitrile SafeSkin gloves. The level of dexterity provided by latex and nitrile SafeSkin gloves for tasks on a gross dexterity level are comparable and health workers will benefit from the non-allergenic properties of nitrile. For tasks requiring fine finger dexterity nitrile SafeSkin gloves may impede dexterity. Despite this, the degree of restriction appears to have a negligible impact on safety in this study when compared with the risk of latex sensitization and subsequent allergy. In addition to glove material, working practices must also take into account glove size, fit, grip and thickness, as these factors can all influence dexterity.

  1. Natural rubber latex: determination and interpretation of flow curves

    Directory of Open Access Journals (Sweden)

    Harrison Lourenço Corrêa

    2015-08-01

    Full Text Available AbstractAs consumers become more demanding, the importance grows of guaranteeing the quality of products. The employment of reliable testing techniques that assure the origin and characteristics of the inputs used by industry is a key factor in this respect. In the rubber processing industry, the most commonly used characterization tests include determination of the total solids and dry rubber content, mechanical stability, odor, color and presence of volatile compounds, among others. For the most part, these tests are sufficient for the latex transformation industry. However, in situations where there is a need to know the behavior of latex in reaction to the mechanical forces of machines (mixers, pumps, etc., other tests must be used. Rheological tests to determine viscoelastic data by means of plotting flow curves combined with the application of theoretical models can provide important details for characterization of different types of latex. This article presents the protocol employed by the Rheology and Image Laboratory of Rio de Janeiro State University (UERJ for the rheological study of Brazilian latex. The samples analyzed came from the state of São Paulo.

  2. Latex glove sensitivity amongst diagnostic imaging healthcare personnel: a self-reporting investigation

    International Nuclear Information System (INIS)

    Healy, Jan; Brennan, Patrick C.; Bowden, Julie Anne

    2003-01-01

    The use of latex gloves has risen dramatically among healthcare workers resulting in an increase in the number of workers experiencing reactions to gloves. Little evidence of reactions among Irish healthcare workers is available. The current, self-reporting study investigated the prevalence to latex gloves amongst four professional groups within three Diagnostic Imaging Departments. Prevalence is similar to that demonstrated elsewhere with 18.3% of individuals expressing latex associated symptoms. Symptoms included itching and redness of hands, dry cracked skin, soreness of eyes and upper respiratory tract complaints. These results indicate that latex hypersensitivity is a real problem amongst Irish healthcare workers. This preliminary work provides the basis of a much larger controlled study currently being planned

  3. Radiation vulcanization of natural rubber latex with low energy accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Haque, Emdadul; Makuuchi, Keizo; Ikeda, Kenichi; Yoshii, Fumio; Kume Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Mitomo, Hiroshi [Gunma Univ., Faculty of Engineering, Department of Biological and Chemical Engineering, Kiryu, Gunma (Japan)

    2001-03-01

    The radiation vulcanization of natural rubber latex (RVNRL) with the recently installed electron beam (EB) pilot plant at Takasaki Radiation Chemistry Research Establishment, Takasaki, Japan has been discussed. The accelerating voltage and beam current of the plant are 250 kV and 10 mA respectively. The plant has a reaction vessel with the capacity of 18 liters latex to irradiate at a time. In order to obtain a suitable setting of experimental for RVNRL under EB of the plant the parameters such as irradiation time, defoamer concentration, volume of latex, beam current etc. are being optimized by varying the individual parameter at a constant set of the other variables. (author)

  4. Identification and characterization of Euphorbia nivulia latex proteins.

    Science.gov (United States)

    Badgujar, Shamkant B; Mahajan, Raghunath T

    2014-03-01

    The protein profile of latex of Euphorbia nivulia Buch.-Ham. is established. Three new proteins viz., Nivulian-I, II and III have been purified to homogeneity from the latex. The relative molecular masses of Nivulian-I, II and III are 31,486.985, 43,670.846 and 52,803.470 Da respectively. Nivulian-I is a simple type of protein while Nivulian-II and III are glycoproteins. Peptide mass fingerprint analysis revealed peptides of these proteins match with Tubulin alpha-1 chain of Eleusine indica, Maturase K of Banksia quercifolia and hypothetical protein of Zea mays respectively. Tryptic digestion profile of Nivulian-I, II and III, infer the exclusive nature of latex origin proteins and may be new and are additive molecules in the dictionaries of phytoproteins or botany. This is the first of its kind, regarding characterization and validation of Nivulian-I, II and III with respect to peptide sequencing. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Foam concrete of increased strength with the thermomodified peat additives

    Science.gov (United States)

    Kudyakov, A. I.; Kopanitsa, N. O.; Sarkisov, Ju S.; Kasatkina, A. V.; Prischepa, I. A.

    2015-01-01

    The paper presents the results of research of foam concrete with thermomodified peat additives. The aim of the research was to study the effect of modifying additives on cement stone and foam concrete properties. Peat additives are prepared by heat treatment of peat at 600 °C. Two approaches of obtaining additives are examined: in condition of open air access (TMT-600) and in condition of limited air access (TMT-600-k). Compressive strength of a cement stone with modifiers found to be increased by 28.9 - 65.2%. Introducing peat modifiers into foam concrete mix leads to increase of compressive strength by 44-57% at 28- day age and heat conductivity of foam concrete decreases by 0.089 W/(m·°C).

  6. Antimalarial Anthrone and Chromone from the Leaf Latex of Aloe ...

    African Journals Online (AJOL)

    In Ethiopian traditional medicine, the leaf latex of Aloe debranan Chrstian is used for the treatment of several diseases including malaria. In an ongoing search for effective, safe and cheap antimalarial agents from plants, the leaf latex of A. debrana was tested for its in vivo antimalarial activity, in a 4-day suppressive assay ...

  7. Polylactide/Montmorillonite Hybrid Latex as a Barrier Coating for Paper Applications

    Directory of Open Access Journals (Sweden)

    Davide Bandera

    2016-03-01

    Full Text Available We developed a paper coating for the potential application in food packaging based on polylactide and montmorillonite. It is applied to the paper in the form of a stable, water-based latex with a solid content of 25–28 wt %. The latex is prepared from a commercially available polylactide, surfactants, montmorillonite, a plasticizer, chloroform (to be removed later and water by an emulsion/solvent evaporation procedure. This coating formulation is applied to the paper substrate by bar-coating, followed by hot-pressing at 150 °C. The coated papers achieved up to an 85% improvement in water vapor transmission rates when compared to the pristine papers. The coating latex is prepared from inexpensive materials and can be used for a solvent-free coating process. In addition, the ingredients of the latex are non-toxic; thus, the coated papers can be safely used for food packaging.

  8. Study of Antibacterial Activity and Bacteriology of Latex from Asclepias syriaca L

    Science.gov (United States)

    McCay, Steven; Mahlberg, Paul

    1973-01-01

    Whole and fractionated latex of Asclepias syriaca was tested for antimicrobial or growth-promoting activity with 16 genera and species of bacteria. Latex and extracted fractions (distilled water, acetic acid, sodium bicarbonate, sulfuric acid, and ethyl ether) possessed no detectable antimicrobial activity. Comparison of growth curves of selected bacteria incubated with serum and rubber fractions, as well as controls, revealed no detectable inhibition of growth, except for a slight inhibitory response to autoclaved serum. Most bacteria were capable of utilizing latex for a substrate as indicated by the increased growth rate in the exponential phase. The stationary phase was entered simultaneously by both the treated cultures and the controls. Various bacteria cultured in a litmus latex mixture yielded populations which ranged from <104 organisms/ml for Lactobacillus casei, Staphylococcus aureus and Micrococcus lysodeikticus to 1.1 × 1010 organisms/ml for Clostridium acetobutylicum. Whole latex, as well as the serum and rubber fractions, support the growth of various bacteria, but under field conditions there is no evidence for systemic infection of this type of cell by bacteria. PMID:4790590

  9. High concentrations of natural rubber latex allergens in gloves used ...

    African Journals Online (AJOL)

    Introduction. Gloves made of natural rubber latex (NRL) are commonly used by healthcare workers because of their good qualities. However, allergic reactions to latex allergens are still commonly reported. Objective. To measure the concentrations of Hev b 1, Hev b 3, Hev b 5 and Hev b 6.02 allergens in gloves used by a ...

  10. Application of radiation vulcanized natural rubber latex in Indonesia

    International Nuclear Information System (INIS)

    Soebianto, Y.S.; Wiwik Sofiarti; Razzak, M.T.

    1996-01-01

    The center has carried out R and D of Radiation Vulcanization Natural Rubber Latex (RVNRL) technology and introduced it to the industries since the inauguration and operation of the latex pilot plant in 1983. After years of experiences and the environmental consideration, n-butylacrylate (n-BA) has replaced CCI, as the sensitizer. Until now the introduction program shows that radiation vulcanized latex is more suitable for home industries than large industries. The obstacle of the program is the marketing of the dipped products. In spite of these problems, the introduction of this technology to the people in some undeveloped area of Java has supported the national program to improve their living standard. The problems of nitrosamine and protein allergic have turn up RVNRL to be the substitute of sulfur vulcanized latex in the future. The cooperation with a national condom manufacturer (PT Mitra Banjaran) has applied RVNRL for condom production in the large scale. Soft condoms with less probability of pinhole are obtained, but the technical problem is stickiness after pilling. Supply to a baby teat and a rubber thread manufacturer offers great advantages by not using any chemicals. In spite of the advantages, the problem of latex viscosity for dipping and the low modulus of elasticity of the threads arise. Through those input CAIR-BATAN is conducting the research and development in improving the crosslinking among the rubber particles that are supposed to be the reason of the stickiness and low modulus of elasticity. This effort is expected to be able to broaden the application of RVNRL, and it will be achieved only by the involvement of rubber chemist, rubber technologist, and radiation chemist

  11. Histamine mediates the pro-inflammatory effect of latex of Calotropis procera in rats

    Directory of Open Access Journals (Sweden)

    Yatin M. Shivkar

    2003-01-01

    Full Text Available Introduction: Calotropis procera is known to produce contact dermatitis and the latex of this plant produces intense inflammation when injected locally. However, the precise mode of its pro-inflammatory effect is not known. In present study we have pharmacologically characterized the inflammation induced by latex of C. procera in a rat paw edema model and determined the role of histamine in latex-induced inflammation.

  12. Pilot scale experiments on radiation vulcanization of NR latex

    International Nuclear Information System (INIS)

    Ridwan, M.

    1985-01-01

    The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accommodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components: emulsification unit, mixing unit and vulcanization reactor. The first two components are located outside shielded room while the third one in irradiation room. The radiation vulcanization process is a much simpler energy saving process compared to the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR latex are comparable to those of sulfur vulcanized. (author)

  13. Molluscicidal effect of Euphorbia umbellata (Pax Bruyns latex on Biomphalaria glabrata, Schistosoma mansoni host snail

    Directory of Open Access Journals (Sweden)

    Luciana Patrícia Lima Alves Pereira

    2017-12-01

    Full Text Available ABSTRACT Euphorbia umbellata (Pax Bruyns is an easily cultivated shrub, with occurrence in the tropical regions of the American and African continents. Chemical studies have revealed that the latex of this plant is rich in terpene compounds, which are highly toxic to snails Biomphalaria glabrata (Basommatophora: Planorbidae. The aim of this study was to evaluate the chemical composition and molluscicidal activity of the latex produced by E. umbellata, as well as the safety of its application in aquatic environments. The concentration of latex that killed 90% of the exposed snails after 24 h exposure (LC90 was 3.69 mg/L. Toxicity bioassays using Danio rerio (zebrafish revealed that these animals were less susceptible to latex than planorbids. However, it is important to perform other toxicity tests to ensure the feasibility of using latex to control populations of mollusks that contribute to schistosomiasis transmission. A phytochemical screening performed with the E. umbellata latex identified the triterpenoid and coumarin class. Further studies are warranted to isolate, identify, and test the active compounds of E. umbellata latex in B. glabrata.

  14. Study on irradiation condition in radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Zhu Nankang; Wang Chunlei; Makuuchi, K.; Yoshii, F.

    1996-01-01

    The effect of gamma rays irradiation dose rates on RVNRL preparation was studied using Malaysian latex added with O.2 phr of KOH and 5 phr n-BA. The results showed, to ensure the tensile strength of the latex film meet the requirement, when applying vulcanisation doses, Dv of 20 kGy 20 and 15 kGy, irradiation dose rates should not be greater than 0. 49 kGy/hr and 1. 6 kGy/hr respectively. Its was found that within the storage time of 20 days there was no change in the physical properties of the latex films

  15. Respiratory and dermal symptoms in Thai nurses using latex products.

    Science.gov (United States)

    Supapvanich, C; Povey, A C; de Vocht, F

    2013-09-01

    Despite known health risks related to the use of powdered latex gloves (PLGs), they are still widely used in hospitals in developing countries due to the high cost of alternatives. To determine the prevalence of dermal and respiratory symptoms associated with latex glove use in nurses in Thailand and evaluate the influence of previously reported occupational risk factors in this population. A cross-sectional study in female nurses working in three Thai hospitals. Participants completed a questionnaire on demographics, occupational and personal history, use of latex products at work and dermal and respiratory symptoms attributed to occupational use of latex gloves. Of 899 nurses, 18% reported health effects attributed to the use of latex products. After adjustment for confounding, occupational risk factors associated with increased reporting of dermal symptoms included wearing more than 15 pairs of PLG per day (odds ratio (OR): 2.10, 95% confidence interval (CI): [1.32-3.34]), using chlorhexidine (OR: 2.07, 95% CI: [1.22-3.52]) and being an operating theatre nurse (OR: 2.46, 95% CI: [1.47-4.12]). Being a labour ward nurse (OR: 3.52, 95% CI: [1.26-9.85]) was the only factor associated with increased reporting of respiratory symptoms. Continuing use of PLGs in Thai nurses is associated with increased prevalence of dermal symptoms compared with data from developed countries. Measures to reduce such health effects are well established and should be considered. Additionally, replacement of chlorhexidine with an alternative detergent seems advisable.

  16. Aggregation and charging of sulfate and amidine latex particles in the presence of oxyanions.

    Science.gov (United States)

    Sugimoto, Takuya; Cao, Tianchi; Szilagyi, Istvan; Borkovec, Michal; Trefalt, Gregor

    2018-08-15

    Electrophoretic mobility and time resolved light scattering are used to measure the effect on charging and aggregation of amidine and sulfate latex particles of different oxyanions namely, phosphate, arsenate, sulfate, and selenate. In the case of negatively charged sulfate latex particles oxyanions represent the coions, while they represent counterions in the case of the positively charged amidine latex. Repulsive interaction between the sulfate latex surface and the coions results in weak ion specific effects on the charging and aggregation. On the other hand the interaction of oxyanions with the amidine latex surface is highly specific. The monovalent dihydrogen phosphate ion strongly adsorbs to the positively charged surface and reverses the charge of the particle. This charge reversal leads also to the restabilization of the amidine latex suspension at the intermediate phosphate concentrations. In the case of dihydrogen arsenate the adsorption to amidine latex surface is weaker and no charge reversal and restabilization occurs. Similar differences are seen between the sulfate and selenate analogues, where selenate adsorbs more strongly to the surface as compared to the sulfate ion and invokes charge reversal. The present results indicate that ion specificity is much more pronounced in the case of counterions. Copyright © 2018 Elsevier Inc. All rights reserved.

  17. Managing latex allergies at home

    Science.gov (United States)

    ... Associate Clinical Professor of Medicine, Division of Allergy, Immunology, and Rheumatology, Georgetown University Medical School, Washington, DC. Also reviewed by David Zieve, MD, MHA, Isla Ogilvie, PhD, and the A.D.A.M. Related MedlinePlus Health Topics Latex Allergy Browse the Encyclopedia A.D.A. ...

  18. Effect of heterogeneous distribution of crosslink density on physical properties of radiation vulcanized NR (Natural Rubber) latex film

    International Nuclear Information System (INIS)

    Keizo Makuuchi; Fumio Yoshii; Miura, H.; Murakami, K.

    1996-01-01

    Thus a study has been carried out to investigate the effect of particle to particle variation in crosslink density on physical properties of radiation vulcanized NR latex film. NR latex was irradiated in small bottle by γ rays without vulcanization accelerator to provide latex rubber particles having homogeneous distribution of crosslink density. The doses were 30, 50, 100, 250, 300, 400, 500 and 600 kGy. Weight swelling ratio, gel fraction, tensile strength and elongation at break of the latex film from the mixed latex were measured. The vulcanization dose of this latex was 250 kGy. Then the two different latexes were mixed in a such way to adjust the average dose of 250 kGy to prepare a latex consisting of rubber particles having heterogeneous distribution of crosslink density. Tensile strength of the latex film was depressed by mixing. The reduction increased with increasing the decrease of gel fraction by mixing. However the reduction was not serious when the dose difference of two latexes was less than 200 kGy

  19. Biological safety evaluation of the modified urinary catheter

    Energy Technology Data Exchange (ETDEWEB)

    Kowalczuk, Dorota, E-mail: dorota.kowalczuk@umlub.pl [Department of Medicinal Chemistry, Medical University of Lublin, Jaczewskiego 4, 20-090 Lublin (Poland); Przekora, Agata; Ginalska, Grazyna [Department of Biochemistry and Biotechnology, Medical University of Lublin, Chodzki 1, 20-093 Lublin (Poland)

    2015-04-01

    The purpose of this study was to evaluate in vitro safety of the novel tosufloxacin (TOS)-treated catheters with the prolonged antimicrobial activity. The test samples of silicone latex catheter were prepared by the immobilization of TOS on chitosan (CHIT)-coated catheter by means of covalent bonds and non-covalent interactions. Each step of the modification process of catheter surface was observed using ATR–Fourier transform infrared spectroscopy. In vitro cytotoxicity of the modified and unmodified catheters was assessed by direct and indirect tests in accordance with ISO standards using green monkey kidney (GMK) cell line. The MTT, lactate dehydrogenase activity (LDH), WST-8, Sulforhodamine B (SRB) test results and microscopic observation clearly indicated that unmodified silicone latex catheters decrease cell metabolic activity, act as a cytotoxic agent causing cell lysis and induce cell death through necrotic or apoptotic process. We suggest that chitosan coat with TOS immobilized limits leaching of harmful agents from silicone latex material, which significantly enhances survivability of GMK cells and therefore is quite a good protection against the cytotoxic effect of this material. - Highlights: • Characterization of the novel antimicrobial urinary catheters • Monitoring of the catheter modification by FTIR analysis • Confirmation of high cytotoxicity of latex-based catheter used in urological practice • Chitosan-coated and tosufloxacin-treated catheter is less toxic than the untreated one. • The proposed surface modification protects cells against latex-induced death.

  20. Radiation vulcanization of natural rubber latex using irradiation n-butyl acrylate aqueous emulsion as sensitizer

    International Nuclear Information System (INIS)

    Vo Van Thien; Nguyen Quoc Hien; Keizo Makuuchi; Fumio Yoshii

    2000-01-01

    Natural rubber latex was vulcanized by gamma radiation with n-butyl acrylate aqueous emulsion irradiated at dose of 1.5 kGy as sensitizer. The total solid content of latex increases on the irradiation dose. The viscosity of latex on the standing time was investigated and became stable after one month of storage. The gel content of latex films increasing with irradiation dose and attained more than 94% at dose of 10 kGy. Tensile strength of films reached the values of 31MPa; 30 Mpa and 25 Mpa at vulcanization doses of 20 kGy, 15 kGy and 8 kGy for the concentrations of sensitizer 7 phr, 9 phr and 13 phr respectively. Elongation at break decreases as increasing dose. Tear strength of rubber films was from 30-40 N/mm. The tackiness of latex films decreases and smell of vulcanized latex is almost negligible. (author)

  1. STRENGTH OF NANOMODIFIED HIGH-STRENGTH LIGHTWEIGHT CONCRETES

    Directory of Open Access Journals (Sweden)

    NOZEMTСEV Alexandr Sergeevich

    2013-02-01

    Full Text Available The paper presents the results of research aimed at development of nanomodified high-strength lightweight concrete for construction. The developed concretes are of low average density and high ultimate compressive strength. It is shown that to produce this type of concrete one need to use hollow glass and aluminosilicate microspheres. To increase the durability of adhesion between cement stone and fine filler the authors offer to use complex nanodimensinal modifier based on iron hydroxide sol and silica sol as a surface nanomodifier for hollow microspheres. It is hypothesized that the proposed modifier has complex effect on the activity of the cement hydration and, at the same time increases bond strength between filler and cement-mineral matrix. The compositions for energy-efficient nanomodified high-strength lightweight concrete which density is 1300…1500 kg/m³ and compressive strength is 40…65 MPa have been developed. The approaches to the design of high-strength lightweight concrete with density of less than 2000 kg/m³ are formulated. It is noted that the proposed concretes possess dense homogeneous structure and moderate mobility. Thus, they allow processing by vibration during production. The economic and practical implications for realization of high-strength lightweight concrete in industrial production have been justified.

  2. Modified chloride diffusion model for concrete under the coupling effect of mechanical load and chloride salt environment

    Science.gov (United States)

    Lei, Mingfeng; Lin, Dayong; Liu, Jianwen; Shi, Chenghua; Ma, Jianjun; Yang, Weichao; Yu, Xiaoniu

    2018-03-01

    For the purpose of investigating lining concrete durability, this study derives a modified chloride diffusion model for concrete based on the odd continuation of boundary conditions and Fourier transform. In order to achieve this, the linear stress distribution on a sectional structure is considered, detailed procedures and methods are presented for model verification and parametric analysis. Simulation results show that the chloride diffusion model can reflect the effects of linear stress distribution of the sectional structure on the chloride diffusivity with reliable accuracy. Along with the natural environmental characteristics of practical engineering structures, reference value ranges of model parameters are provided. Furthermore, a chloride diffusion model is extended for the consideration of multi-factor coupling of linear stress distribution, chloride concentration and diffusion time. Comparison between model simulation and typical current research results shows that the presented model can produce better considerations with a greater universality.

  3. Synthesis and Characterization of Core-Shell Acrylate Based Latex and Study of Its Reactive Blends

    Directory of Open Access Journals (Sweden)

    Ying Nie

    2008-03-01

    Full Text Available Techniques in resin blending are simple and efficient method for improving the properties of polymers, and have been used widely in polymer modification field. However, polymer latex blends such as the combination of latexes, especially the latexes with water-soluble polymers, were rarely reported. Here, we report a core-shell composite latex synthesized using methyl methacrylate (MMA, butyl acrylate (BA, 2-ethylhexyl acrylate (EHA and glycidyl methacrylate (GMA as monomers and ammonium persulfate and sodium bisulfite redox system as the initiator. Two stages seeded semi-continuous emulsion polymerization were employed for constructing a core-shell structure with P(MMA-co-BA component as the core and P(EHA-co-GMA component as the shell. Results of Transmission Electron Microscopy (TEM and Dynamics Light Scattering (DLS tests confirmed that the particles obtained are indeed possessing a desired core-shell structural character. Stable reactive latex blends were prepared by adding the latex with waterborne melamine-formaldehyde resin (MF or urea-formaldehyde resin (UF. It was found that the glass transition temperature, the mechanical strength and the hygroscopic property of films cast from the latex blends present marked enhancements under higher thermal treatment temperature. It was revealed that the physical properties of chemically reactive latexes with core-shell structure could be altered via the change of crosslinking density both from the addition of crosslinkers and the thermal treatment.

  4. Experimental Investigation of the Mechanical and Durability Properties of Crumb Rubber Concrete.

    Science.gov (United States)

    Liu, Hanbing; Wang, Xianqiang; Jiao, Yubo; Sha, Tao

    2016-03-07

    Recycling waste tire rubber by incorporating it into concrete has become the preferred solution to dispose of waste tires. In this study, the effect of the volume content of crumb rubber and pretreatment methods on the performances of concrete was evaluated. Firstly, the fine aggregate and mixture were partly replaced by crumb rubber to produce crumb rubber concrete. Secondly, the mechanical and durability properties of crumb rubber concrete with different replacement forms and volume contents had been investigated. Finally, the crumb rubber after pretreatment by six modifiers was introduced into the concrete mixture. Corresponding tests were conducted to verify the effectiveness of pretreatment methods as compared to the concrete containing untreated crumb rubber. It was observed that the mechanical strength of crumb rubber concrete was reduced, while durability was improved with the increasing of crumb rubber content. 20% replacement of fine aggregate and 5% replacement of the total mixture exhibited acceptable properties for practical applications. In addition, the results indicated that the modifiers had a positive impact on the mechanical and durability properties of crumb rubber concrete. It avoided the disadvantage of crumb rubber concrete having lower strength and provides a reference for the production of modified crumb rubber concrete.

  5. Experimental Investigation of the Mechanical and Durability Properties of Crumb Rubber Concrete

    Directory of Open Access Journals (Sweden)

    Hanbing Liu

    2016-03-01

    Full Text Available Recycling waste tire rubber by incorporating it into concrete has become the preferred solution to dispose of waste tires. In this study, the effect of the volume content of crumb rubber and pretreatment methods on the performances of concrete was evaluated. Firstly, the fine aggregate and mixture were partly replaced by crumb rubber to produce crumb rubber concrete. Secondly, the mechanical and durability properties of crumb rubber concrete with different replacement forms and volume contents had been investigated. Finally, the crumb rubber after pretreatment by six modifiers was introduced into the concrete mixture. Corresponding tests were conducted to verify the effectiveness of pretreatment methods as compared to the concrete containing untreated crumb rubber. It was observed that the mechanical strength of crumb rubber concrete was reduced, while durability was improved with the increasing of crumb rubber content. 20% replacement of fine aggregate and 5% replacement of the total mixture exhibited acceptable properties for practical applications. In addition, the results indicated that the modifiers had a positive impact on the mechanical and durability properties of crumb rubber concrete. It avoided the disadvantage of crumb rubber concrete having lower strength and provides a reference for the production of modified crumb rubber concrete.

  6. Progress in radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Makuuchi, Keizo

    2000-01-01

    Vulcanization dose defined as the radiation dose at which cross-linked natural rubber in latex has the maximum tensile strength can be reduced by adding carbon tetrachloride as a reaction accelerator. The radiation vulcanization of natural rubber latex was selected as one of regional projects of IAEA in 1989 and a pilot plant was built in Jakarta. The products from it were evaluated during 1983-1985, followed by IAEA decision to support the continued R and D study at Takasaki, JAERI. Various factors to improve the properties of the products have been studied. Several advantages of the process over conventional method, such as absence of N-nitrosoamines, low cytotoxicity, decomposability in the environment, transparency and softness, were confirmed. The technology has been transferred toward commercial application in Thailand, and pilot plants being set up in Indonesia, India, Malaysia and Thailand. Moreover, the process was found to be effective in reducing protein remaining in natural rubber latex products and the initial investment and irradiation cost was found to be greatly reduced by employing low energy electron accelerator. This paper reviews such progress. (S. Ohno)

  7. Extractable protein of radiation vulcanized natural rubber latex

    International Nuclear Information System (INIS)

    Soebianto, Y.S.; Ratnayake, U.M.; Makuuchi, Keizo; Yoshii, Fumio; Kume, Tamikazu

    2000-01-01

    Protein remained in the latex products are reported to cause serious allergy. A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) in three different processes. The amount of WSP was 3 phr. It was only added to RVNRL (standard), added to re-centrifuged RVNRL (pre-centrifugation), and added to RVNRL followed by centrifugation (post-centrifugation). The protein content was determined by enhanced BCA method, and identified by SDS-PAGE. Extractable protein (EP) from the rubber has been reduced up to the minimum protein detection by combining WSP addition and centrifugation. Short leaching time (20-30 min.) can be achieved after the combine treatment, and SDS-PAGE confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The efficiency of protein removal by WSP depends on its molecular weight of WSP which relates to its water solubility. (author)

  8. IMMEDIATE AND DELAYED HYPERSENSITIVITY REACTIONS TO LATEX GLOVES IN A DENTAL STUDENT. A case report.

    Directory of Open Access Journals (Sweden)

    Iliyana Stoeva

    2011-08-01

    Full Text Available The article presents a case of dental student with immediate and delayed hypersensitivity reaction to latex gloves. Symptoms appeared during the second year of regularly using of latex gloves. The student was with no history of allergies and no previous exposure to latex products.

  9. Preparation of novel film-forming armoured latexes using silica nanoparticles as a pickering emulsion stabiliser.

    Science.gov (United States)

    Shiraz, Hana; Peake, Simon J; Davey, Tim; Cameron, Neil R; Tabor, Rico F

    2018-05-15

    Film-forming polymer latex particles of diameter acrylate (BA) as co-monomers, potassium persulphate (KPS) as an initiator and a commercially available colloidal nano-silica (Ludox®-TM40). It was found that pH control before polymerisation using methacrylic acid (MAA) facilitated the formation of armoured latexes, and mechanistic features of this process are discussed. An alternative, more robust protocol was developed whereby addition of vinyltriethoxysilane (VTES) to control wettability resulted in latexes completely armoured in colloidal nano-silica. The latexes were characterised using SEM, cryo-TEM and AFM imaging techniques. The mechanism behind the adsorption was investigated through surface pressure and contact angle measurements to understand the factors that influence this irreversible adsorption. Results indicate that nanoparticle attachment (but intriguingly not latex size) is dependent on particle wettability, providing new insight into the formation of nanoparticle-armoured latexes, along with opportunities for further development of diversely functionalized inorganic/organic polymer composite particles. Copyright © 2018 Elsevier Inc. All rights reserved.

  10. Structure formation control of foam concrete

    Science.gov (United States)

    Steshenko, Aleksei; Kudyakov, Aleksander; Konusheva, Viktoriya; Syrkin, Oleg

    2017-01-01

    The process of predetermined foam concrete structure formation is considered to be a crucial issue from the point of process control and it is currently understudied thus defining the need for additional research. One of the effective ways of structure formation control in naturally hardening foam concrete is reinforcement with dispersed fibers or introduction of plasticizers. The paper aims at studying the patterns of influence of microreinforcing and plasticizing additives on the structure and performance properties of foam concrete. Preparation of foam concrete mix has been conducted using one-step technology. The structure of modified foam concrete has been studied by means of electron microscopy. The cellular structure of foam concrete samples with the additives is homogeneous; the pores are uniformly distributed over the total volume. It has been revealed that introduction of the Neolas 5.2 plasticizer and microreinforcing fibers in the foam concrete mixture in the amount of 0.4 - 0.1 % by weight of cement leads to reduction of the average pore diameter in the range of 45.3 to 30.2 microns and the standard deviation of the pore average diameter from 23.6 to 9.2 in comparison with the sample without additive. Introduction of modifying additives has stimulated formation of a large number of closed pores. Thus porosity of conditionally closed pores has increased from 16.06 % to 34.48 %, which has lead to increase of frost resistance brand of foam concrete from F15 to F50 and to reduction of its water absorption by weight by 20 %.

  11. Impact capacity reduction in railway prestressed concrete sleepers with vertical holes

    Science.gov (United States)

    Ngamkhanong, Chayut; Li, Dan; Kaewunruen, Sakdirat

    2017-09-01

    Railway prestressed concrete sleepers (or railroad ties) are principally designed in order to carry wheel loads from the rails to the ground as well as to secure rail gauge for dynamic safe movements of trains. In spite of the most common use of the prestressed concrete sleepers in railway tracks, the concrete sleepers are often modified on construction sites to fit in other systems such as cables, signalling gears, drainage pipes, etc. This is because those signalling, fibre optic, equipment cables are often damaged either by ballast corners or by tamping machine. It is thus necessary to modify concrete sleepers to cater cables internally so that the cables or drainage pipes would not experience detrimental or harsh environments. Accordingly, this study will extend from the previous study into the design criteria of holes and web openings. This paper will highlight structural capacity of concrete sleepers under dynamic transient loading. The modified compression field theory for ultimate strength design of concrete sleepers will be highlighted in this study. The outcome of this study will improve the understanding into dynamic behavior of prestressed concrete sleepers with vertical holes. The insight will enable predictive track maintenance regime in railway industry.

  12. Science and technology of rubber reclamation with special attention to NR based waste latex products

    NARCIS (Netherlands)

    Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

    2006-01-01

    A comprehensive overview of reclamation of cured rubber with special emphasis on latex reclamation is depicted in this paper. The latex industry has expanded over the years to meet the world demands for gloves, condoms, latex thread, etc. Due to the strict specifications for the products and the

  13. Preliminary study of semi-refined carrageenan (SRC) as secondary gelling agent in natural rubber (NR) latex foam

    Science.gov (United States)

    Norhazariah, S.; Azura, A. R.; Azahari, B.; Sivakumar, R.

    2017-12-01

    Semi-refined carrageenan (SRC) product is considerably cheaper and easier to produce as a natural polysaccharide, which was utilized in food and other product application. However, the application in latex is limited. The aim of this work is to evaluate the SRC produced from low industrial grade seaweed (LIGS) in the latex foam application. The FTIR spectra showed the SRC produced as kappa type carrageenan with lower sulfur content compared to native LIGS. NR latex foam is produced by using the Dunlop method with some modifications. The effect of SRC loading as a secondary gelling agent in NR latex foam is investigated. The density and morphology of the NR latex foam with the addition of the SRC are analyzed. NR latex foam density increased with SRC loading and peaked at 1.8 phr SRC. The addition of SRC has induced the bigger cell size compared to the cell size of the control NR latex foam, as shown in the optical micrograph. It can be concluded that SRC LIGS could be acted as secondary gelling agent in NR latex foam.

  14. Radiation vulcanization of natural rubber latex (NRL) using low energy electron beam accelerator

    International Nuclear Information System (INIS)

    Feroza Akhtar; Keizo Makuuchi; Fumio Yoshii

    1996-01-01

    The electron beam induced vulcanization of natural rubber latex has been studied using low energy Electron Beam (EB) accelerators of 300, 250 and 175 keV ne latex was irradiated in a special type stainless steel reaction reactor with a stirrer at the bottom of the reactor. From the results it was found that 300 and 250 keV accelerators could effectively vulcanize NRL. But accelerator of 175 keV is too low energy to vulcanize the latex. At the same time a drum type irradiator where thin layer of NRL was irradiated by accelerator, was used for vulcanization of NRL. This type of irradiator also showed good physical properties of vulcanized latex. The effects of beam current and stirrer speed on vulcanization were studied

  15. The physicochemical quality and meat microstructure of post laying hen with addition of Biduri (Calotropis gigantea) latex extract

    Science.gov (United States)

    Nuhriawangsa, A. M. P.; Hertanto, B. S.; Kartikasari, L. R.; Swastike, W.; Cahyadi, M.; Rasid, S.

    2018-01-01

    The objective of this study was to evaluate the effect of extract level of Biduri latex on the meat quality of laying hens. The materials of this research were Biduri latex and thigh meat from hens strain Lohman. The latex was tapped from a young tissue stem and centrifuged for its supernatant. Meats were smeared with latex, punctured and incubated for 30 minutes. Concentrations of latex were 0, 3, 6 and 9% from the weight of meat (w/w). The variables were water, dissolved protein, crude fat content, tenderness and microstructure of meat. The statistical analysis method using ANOVA and if there was a mean difference, Duncan test was used. Descriptive analysis was used for microstructures of meat by comparing its hydrolysis conditions. The study showed that fat had significant difference (P meat structure. The fat content increased with addition of 3% latex. The value of dissolved protein increased but tenderness decreased by addition extract of 6% latex. The addition of Biduri latex extract showed that hydrolysis in the microstructure of meat. The addition of 6% latex was the best meat quality.

  16. Benefits of aggregates surface modification in concrete production

    Science.gov (United States)

    Junak, J.; Sicakova, A.

    2017-10-01

    In our study, recycled concrete aggregates (RCA), which surfaces had been modified by geopolymer material based on coal fly ash, were used to produce the concrete samples. In these samples, fraction 4/8 mm was replaced by recycled concrete aggregate with a range of 100%. To modify the surface of RCA was “Solo” and “Triple stage” modification used. On these samples real density, total water absorption and compressive strength were examined after 28, 90, 180 and 365 days of hardening. The highest compressive strength 56.8 MPa, after 365 days hardening, reached sample which had improved RCA surface by “Triple stage mixing”.

  17. Using Modified Concrete for Removing Chromium From Wastewater

    Directory of Open Access Journals (Sweden)

    Elham Asrari

    2016-11-01

    Full Text Available Background Annual large amounts of wastewater can be entered into the environment from domestic, agricultural, and industrial sources that contain high concentrations of chemical materials and heavy metals. Chromium (Cr is one of the most important environmental pollutants, which can cause pollution of water resources and disorder in the metabolic activities of living organisms. Objectives In this study, we used the alteration in the concrete structure by iron oxide nanoparticles and rice husk ash (RHA to remove Cr as a heavy metal from sewage. Methods Rice husk ash was used in the structure of concrete as a forty percent by cement weight. Samples were made according to sewage condition and concrete required strength of purification pools. Samples' surface was covered with nanoparticle, RHA, RHA and nanoparticle. Different sewage concentrations of Cr were made from the range of 1 to 1000 ppm. The effects of parameters, such as contact time, adsorbent dose, pH, concentration of Cr in sewage, and Cr absorption were examined. Results The maximum absorption was obtained 99.7%, in the contact time of 6 hours, dose of adsorbent 20 mg/L, pH 3, and Cr concentration in sewage 10 ppm at the laboratory temperature. Cr absorption followed the Freundlich model of adsorption. Conclusions The combination of nanoparticles and RHA showed well efficiency for Cr absorption from sewage.

  18. Latex Rubber Gloves as a Sampling Dosimeter Using a Novel Surrogate Sampling Device.

    Science.gov (United States)

    Sankaran, Gayatri; Lopez, Terry; Ries, Steve; Ross, John; Vega, Helen; Eastmond, David A; Krieger, Robert I

    2015-01-01

    Pesticide exposure during harvesting of crops occurs primarily to the workers' hands. When harvesters wear latex rubber gloves for personal safety and hygiene harvesting reasons, gloves accumulate pesticide residues. Hence, characterization of the gloves' properties may be useful for pesticide exposure assessments. Controlled field studies were conducted using latex rubber gloves to define the factors that influence the transfer of pesticides to the glove and that would affect their use as a residue monitoring device. A novel sampling device called the Brinkman Contact Transfer Unit (BCTU) was constructed to study the glove characteristics and residue transfer and accumulation under controlled conditions on turf. The effectiveness of latex rubber gloves as sampling dosimeters was evaluated by measuring the transferable pesticide residues as a function of time. The validation of latex rubber gloves as a residue sampling dosimeter was performed by comparing pesticide transfer and dissipation from the gloves, with the turf transferable residues sampled using the validated California (CA) Roller, a standard measure of residue transfer. The observed correlation (Pearson's correlation coefficient R(2)) between the two methods was .84 for malathion and .96 for fenpropathrin, indicating that the BCTU is a useful, reliable surrogate tool for studying available residue transfer to latex rubber gloves under experimental conditions. Perhaps more importantly, these data demonstrate that latex gloves worn by workers may be useful quantifiable matrices for measuring pesticide exposure.

  19. Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

    International Nuclear Information System (INIS)

    Dessouki, A.M.; Taher, N.H.; El-Nahas, H.H.

    1996-01-01

    The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the ζ potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs

  20. Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

    Energy Technology Data Exchange (ETDEWEB)

    Dessouki, A M; Taher, N H; El-Nahas, H H [National Center for Radiation Research and Technology, Atomic Energy Athority, Cairo (Egypt)

    1996-03-01

    The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the {zeta} potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs.

  1. Labbtex: Toolbox para generación de informes en LATEX para Matlab

    Directory of Open Access Journals (Sweden)

    José Luis Almazán Gárate

    2012-10-01

    Full Text Available En este artículo se presenta el software desarrollado por el Equipo H3lite dentro del Departamento de Ingeneniería Civil. Transportes de la Escuela de Ingenieros de Caminos, Canales y Puertos de la Universidad Politécnica de Madrid para la generación de informes enLATEX mediante el software Matlab® y la integración en sus rutinas, Labbtex.La librería Labbtex proporciona un marco flexible para mezclar texto y código Matlab® para la generación automática de documentos. Un rchivo fuente simple contiene el texto de documentación y el código Matlab, al correr la aplicación se genera un documento final LATEX que contiene el texto, gráficos y tablas indicados con el formato de un documento LATEX. El código Matlab genera un documento LATEX usando la sintaxis. Así, LATEX (para composición de texto de alta calidad y Matlab® (para cálculo matemático pueden usarse simultáneamente. Esto permite la generación de informes en tiempo real con un uso de recursos mínimo.

  2. Latex Allergy - A Case Report

    Directory of Open Access Journals (Sweden)

    Dr. Athma Prasanna

    2005-10-01

    Full Text Available The usage of rubber and its products are not uncommon in various walks of life. A continuous exposure or contact may sensitize the human body, causing reactions from mild to fatal. Despite the availability of the literature, medical personnel are still unaware of the implications of the use of latex materials.

  3. Latex medical gloves

    DEFF Research Database (Denmark)

    Palosuo, Timo; Antoniadou, Irini; Gottrup, Finn

    2011-01-01

    Many hospitals have implemented policies to restrict or ban the use of devices made of natural rubber latex (NRL) in healthcare as precautionary measures against the perceived risk of NRL allergy. Changes in glove technology, progress in measuring the specific allergenic potential of gloves...... properties of NRL and synthetic gloves and the role of glove powder. The review shows that NRL medical gloves, when compared with synthetic gloves, tend to be stronger, more flexible and better accepted by clinicians. The introduction of powder-free gloves has been associated with reductions in protein...

  4. Formation of Defect-Free Latex Films on Porous Fiber Supports

    KAUST Repository

    Lively, Ryan P.

    2011-09-28

    We present here the creation of a defect-free polyvinylidene chloride barrier layer on the lumen-side of a hollow fiber sorbent. Hollow fiber sorbents have previously been shown to be promising materials for enabling low-cost CO 2 capture, provided a defect-free lumen-side barrier layer can be created. Film experiments examined the effect of drying rate, latex age, substrate porosity (porous vs nonporous), and substrate hydrophobicity/ hydrophilicity. Film studies show that in ideal conditions (i.e., slow drying, fresh latex, and smooth nonporous substrate), a defect-free film can be formed, whereas the other permutations of the variables investigated led to defective films. These results were extended to hollow fiber sorbents, and despite using fresh latex and relatively slow drying conditions, a defective lumen-side layer resulted. XRD and DSC indicate that polyvinylidene chloride latex develops crystallinity over time, thereby inhibiting proper film formation as confirmed by SEM and gas permeation. This and other key additional challenges associated with the porous hollow fiber substrate vs the nonporous flat substrate were overcome. By employing a toluene-vapor saturated drying gas (a swelling solvent for polyvinylidene chloride) a defect-free lumen-side barrier layer was created, as investigated by gas and water vapor permeation. © 2011 American Chemical Society.

  5. Isotactic polypropylene/carbon nanotube composites prepared by latex technology: Electrical conductivity study

    NARCIS (Netherlands)

    Grossiord, N.; Wouters, M.E.L.; Miltner, H.E.; Lu, K.; Loos, J.; Van Mele, B.; Koning, C.E.

    2010-01-01

    Several series of nanocomposites were prepared using a latex-based process, the main step of which consisted of mixing an aqueous suspension of exfoliated carbon nanotubes (CNTs) and a polymer latex. In the present work, a systematic study on the electrical properties of fully amorphous (polystyrene

  6. Proceedings of the international symposium on radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Machi, Sueo

    1990-01-01

    The First International Symposium on Radiation Vulcanization of Natural Rubber Latex (RVNRL) was held from 26 to 28 July 1989 at Tokyo and Takasaki. In these proceedings, thirty six papers presented at the Symposium are compiled. Main topics are commercial application of RVNRL, characterization of NR latex and vulcanization, properties of radiation vulcanized NR latex, development of sensitizers, mechanism of RVNRL, RVNRL with electron beams, and new Co-60 irradiator for RVNRL. Absence of nitrosamines and low cytotoxicity of radiation vulcanized NR latex are recognized as the remarkable advantages of RVNRL. The radiation vulcanization process for the production of protective rubber gloves for radioactive contamination was presented as the first commercial success in RVNRL. It was reported that various kinds of rubber articles for medical uses have being developed in West Germany. A sensitizer system consisting of n-butyl acrylate and t-butyl hydroperoxide was found to reduce the vulcanization dose to 8 kGy. (author)

  7. CDNA library from the Latex of Hevea brasiliensis

    Directory of Open Access Journals (Sweden)

    Wilaiwan Chotigeat

    2010-12-01

    Full Text Available Latex from Hevea brasiliensis contains 30-50% (w/w of natural rubber (cis-1,4-polyisoprene, the important rawmaterial for many rubber industries. We have constructed a cDNA library from the latex of H. brasiliensis to investigate theexpressed genes and molecular events in the latex. We analyzed 412 expressed sequence tags (ESTs. More than 90% of theEST clones showed homology to previously described sequences in public databases. Functional classification of the ESTsshowed that the largest category were proteins of unknown function (30.1%, 11.4% of ESTs encoded for rubber synthesisrelatedproteins (RS and 8.5% for defense or stress related proteins (DS. Those with no significant homology to knownsequences (NSH accounted for 8.7%, primary metabolism (PM and gene expression and RNA metabolism were 7.8% and6.6%, respectively. Other categories included, protein synthesis-related proteins (6.6%, chromatin and DNA metabolism(CDM 3.9%, energy metabolism (EM 3.4%, cellular transport (CT 3.2%, cell structure (CS 3.2%, signal transduction (ST2.2%, secondary metabolism (SM 1.7%, protein fate (PF 2.2%, and reproductive proteins (RP 0.7%.

  8. Pilot scale experiments on radiation vulcanization of NR latex

    Science.gov (United States)

    Ridwan, M.

    The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accomodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components : emulsification unit ( height : 650 mm, diameter 500 mm ), mixing unit ( height : 1900mm, diameter 1200 mm ) and vulcanization reactor ( height : 1800 mm, diameter 1300 mm ). The first two components are located outside shielded room while the third one-in irradiation room. The radiation vulcanization process is a much simpler energy saving process comparedto the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR Latex are comparable to those of sulfur vulcanized, and depend on many factors such as irradiation dose, sensitizer content, dry rubber content and storage time.

  9. Latex imaging by environmental STEM: application to the study of the surfactant outcome in hybrid alkyd/acrylate systems.

    Science.gov (United States)

    Faucheu, Jenny; Chazeau, Laurent; Gauthier, Catherine; Cavaillé, Jean-Yves; Goikoetxea, Monika; Minari, Roque; Asua, José M

    2009-09-01

    Among other uses, latexes are a successful alternative to solvent-borne binders for coatings. Efforts are made to produce hybrid nanostructured latexes containing an acrylic phase and an alkyd phase. However, after the film-forming process, the surfactant used to stabilize these latexes remains in the film, and its location can have a drastic effect on the application properties. Among the processing parameters, the alkyd hydrophobicity can strongly influence this location. This article aims at the imaging of these surfactant molecules in two hybrid latexes with different hydrophobicity level of the alkyd resin. A first part of this paper is dedicated to the understanding of the contrast provided by the surfactant in environmental STEM imaging of latexes. Then, the influence of surfactant-polymer affinity on the surfactant location after film-forming of those hybrid alkyd/acrylate latexes is studied by this technique. It is shown that in the hybrid latex with an alkyd shell (obtained with the most hydrophilic resin), the surfactant molecules tend to remain buried in the alkyd phase. Conversely, in the hybrid latex with an acrylate shell (in the case of the most hydrophobic resin), the surfactant molecules tend to gather into islands like in pure acrylate latex films.

  10. Radiation vulcanization of natural rubber latex with low energy accelerator-II

    Energy Technology Data Exchange (ETDEWEB)

    Haque, Md. Emdadul; Makuuchi, Keizo; Ikeda, Kenichi; Yoshii, Fumio; Kume, Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Mitomo, Hiroshi [Gunma Univ., Faculty of Engineering, Dept. of Biological and Chemical Engineering, Kiryu, Gunma (Japan)

    2002-03-01

    The natural rubber latex (NRL) was radiation vulcanized under a low energy electron accelerator. Accelerating voltage and maximum beam current of this accelerator are 250 kV and 10 mA respectively. Irradiation was carried out in a reaction vessel with constant stirring. The capacity of the vessel is 18 liters. Radiation vulcanization accelerators (RVA) were normal butyl acrylate (n-BA) and nonane-diol-diacrylate (NDDA). NDDA has no bad smell like that of n-BA. 20 minutes irradiation time is enough to vulcanize 14 liters of latex when 5 phr RVA (both types) are used. Maximum of {approx}30 MPa tensile strength was obtained with 5 phr NDD-A. However the remained NDDA is difficult to remove due to high molecular weight. Water-extractable proteins content was determined in dipped films for various leaching conditions without and with additive (polyvinyl alcohol, PVA). Water extractable proteins content is reduced to {<=} 41 by adding 5 phr PVA and leaching for 8 hours. The tackiness of the dipped films is reduced to 0.1 from 9 gf by mixing 6 phr PVA with the irradiated latex. Hand gloves (surgical and examination) were successfully produced from the irradiated latex. (author)

  11. Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex

    International Nuclear Information System (INIS)

    Martins, Carlos Felipe Pinto

    2005-01-01

    The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of 60 C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

  12. Synthesis and characterization of nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Jianhua, E-mail: zhoujianh@21cn.com [College of Resource and Environment, Shaanxi University of Science and Technology, Xi’an 710021 (China); Shaanxi Research Institute of Agricultural Products Processing Technology, Xi’an 710021 (China); Chen, Xin; Duan, Hao; Ma, Jianzhong; Ma, Yurong [College of Resource and Environment, Shaanxi University of Science and Technology, Xi’an 710021 (China)

    2015-03-15

    Graphical abstract: Nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion was synthesized by emulsifier-free emulsion polymerization and sol–gel process using ethyl silicate as precursor for nano-SiO{sub 2}. - Highlights: • Nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion was successfully synthesized by emulsion polymerization using surfmer and sol–gel process. • The contact angle results showed that the finished fabric had an excellent water and oil repellency. • The nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion proved to be highly solvent-resistant and water-resistant. • The transmission electron microscopy (TEM) indicated that the nano-SiO{sub 2} presented on the surface of latex particles. • The atomic force microscope (AFM) and energy dispersive X-ray spectrometer (EDX) confirmed that the hybrid film had a rough surface and the organic fluorine segment could migrate onto the film–air interface. - Abstract: Nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion, consisting of methyl methacrylate, butyl acrylate, dodecafluoroheptyl methacrylate and ethyl silicate, was successfully synthesized by emulsion polymerization using surfmer and sol–gel process. When increasing ethyl silicate content, the latex centrifugal stability decreased, and the latex particle size increased. The contact angle results showed that the finished fabric had an excellent water and oil repellency. Furthermore, compared with fluorine-containing polyacrylate emulsifier-free emulsion, the obtained nano-SiO{sub 2} modified fluorine-containing polyacrylate emulsifier-free emulsion proved to be highly solvent-resistant and water-resistant. In addition, the transmission electron microscopy (TEM) indicated that the nano-SiO{sub 2} presented on the surface of latex particles. The atomic force microscope (AFM) and energy dispersive X-ray spectrometer

  13. Modification of cement concrete by multilayer carbon nano-tubes

    International Nuclear Information System (INIS)

    Yakovlev, G.I.; Pervushin, G.N.; Pudov, I.A.; Korzhenko, A.

    2012-01-01

    The compact structure of protective concrete-conservative on the basis of Portland cement modified by carbon nano-dispersed systems has been studied. Multilayer carbon nano-tubes Graphistrength TM by 'Arkema' dispersed in hydrodynamic plant in the solution of surfactant Polyplast SP-1 have been used as modifying additives. The bending strength of fine grain concrete has been observed to increase by 45.1% and compression strength - by 96.8%. The concrete strength increase is related to morphological changes of crystalline hydrate new formations providing the formation of less defective structure of cement matrix of high density, preventing the migration of radionuclides into the environment in the process of radioactive waste conservation

  14. Thermodynamics of swelling of latex particles with two monomers: a sensitivity analysis

    NARCIS (Netherlands)

    Maxwell, I.A.; Noel, E.F.J.; Schoonbrood, H.A.S.; German, A.L.

    1993-01-01

    A sensitivity anal. is performed to det. at what conditions the simplified model for swelling of latex particles by two monomers or two solvents is valid. This model proposes that, inter alia, the fractions of two monomers in the latex particles and in the monomer droplets are equal. The model is a

  15. Color Spectrum Properties of Pure and Non-Pure LATEX in Discriminating Rubber Clone Series

    International Nuclear Information System (INIS)

    Noor Aishah Khairuzzaman; Hadzli Hashim; Nina Korlina Madzhi; Noor Ezan Abdullah; Faridatul Aima Ismail; Ahmad Faiz Sampian; Azhana Fatnin Che Will

    2015-01-01

    A study of color spectrum properties for pure and non-pure latex in discriminating rubber clone series has been presented in this paper. There were five types of clones from the same series being used as samples in this study named RRIM2002, RRIM2007, RRIM2008, RRIM2014, and RRIM3001. The main objective is to identify the significant color spectrum (RGB) from pure and non-pure latex that can discriminate rubber clone series. The significant information of color spectrum properties for pure and non-pure latex is determined by using spectrometer and Statistical Package for the Social Science (SPSS). Visible light spectrum (VIS) is used as a radiation light of the spectrometer to emit light to the surface of the latex sample. By using SPSS software, the further numerical analysis of color spectrum properties is being conducted. As the conclusion, blue color spectrum for non-pure is able to discriminate for all rubber clone series whereas only certain color spectrum can differentiate several clone series for pure latex. (author)

  16. Elevated temperature effects on concrete properties

    International Nuclear Information System (INIS)

    Grant, P.R.; Gruber, R.S.; Van Katwijk, C.

    1993-08-01

    The design of facilities to process or store radioactive wastes presents many challenging engineering problems. Such facilities must not only provide for safe storage of radioactive wastes but they must also be able to maintain confinement of these materials during and after natural phenomena events. Heat generated by the radioactive decay of the wastes will cause the temperature of the concrete containment structure to increase to a magnitude higher than that found in conventional structures. These elevated temperatures will cause strength-related concrete properties to degrade over time. For concrete temperatures less than 150 degree F, no reduction in strength is taken and the provisions of ACI 349, which states that higher temperatures are allowed if tests are provided to evaluate the reduction in concrete strength properties, apply. Methods proposed in a Pacific Northwest Laboratory (PNL) report, Modeling of Time-Variant Concrete Properties at Elevated Temperatures, can be used to evaluate the effects of elevated temperatures on concrete properties. Using these modified concrete properties the capacity of a concrete structure, subjected to elevated temperatures, to resist natural phenomena hazards can be determined

  17. Properties of sulfur-extended asphalt concrete

    Directory of Open Access Journals (Sweden)

    Gladkikh Vitaliy

    2016-01-01

    Full Text Available Currently, increased functional reliability of asphalt concrete coatings associated with various modifying additives that improve the durability of pavements. Promising builder is a technical sulfur. Asphalt concrete, made using a complex binder consisting of petroleum bitumen and technical sulfur, were calledsSulfur-Extended Asphalt Concrete. Such asphalt concrete, due to changes in the chemical composition of particulate and bitumen, changes the intensity of the interaction at the interface have increased rates of physical and mechanical properties. There was a lack of essential knowledge concerning mechanical properties of the sulfur-bituminous concrete with such an admixture; therefore, we had carried out the necessary examination. It is revealed that a new material satisfies local regulations in terms of compressive and tensile strength, shear resistance, and internal friction.

  18. Extractable proteins from electron beam (EB) irradiated natural rubber (NR) latex

    International Nuclear Information System (INIS)

    Feroza Akhtar; Fumio Yoshii; Keizo Makuuchi

    1996-01-01

    The protein assay of natural rubber latex (NRL) vulcanized by low energy electron beam (EB, 300 keV, 30 mA) has been carried out using Bicinchoninic acid (BCA) reagent. Extractable protein in irradiated latex film was determined by measuring the absorption of colored solution at 562 nm using UV spectrometer. The effect of various radiation doses on the extractable protein content of NRL was investigated. It was ,found that the quantities of extractable protein increases with radiation dose. When compared with ,gamma-ray irradiated samples the same trend was observed. Electron beam irradiated latex films are leached in 1% (ammonia water for various lengths of time. From the results it was established that within 2 hours of leaching in ammonia water most of the extractable protein (96%) were removed from rubber film

  19. Antioxidant and sensitizer effect on the stability of natural rubber latex vulcanized by gamma rays

    International Nuclear Information System (INIS)

    Canavel, V.

    1993-01-01

    The natural rubber latex was vulcanized by gamma rays and electrons beam, in the presence and absence of sensitizer at room temperature. The sensitizers were the following; n-butyl acrylate (n-BA) / t-butyl hydroperoxide (t-B H) / KOH, C Cl 4 / potassium laurate and n-BA / KOH. The studied antioxidants, Irganox 1520, Vulcanox SP and Vulcanox BKF, were added to the latex after irradiation. Among the studied antioxidants in function of tensile strength (TS) after the aging of rubber plates, the Irganox was the best efficient on the gamma vulcanization in the presence of n-BA/t-B H/KOH, because only 0,20 p hr is enough to obtain the greatest increase of TS, that was 34%, 12 MPa to 16 MPa. The formulating method of latex with the sensitizer constituted the 3,0 p hr of n-BA/ 0,1 p hr of t-B H and 0,2 p hr of KOH, was evaluated respecting the TS of rubber plates. The electrons beam vulcanization produces the greatest reversible perturbance in the colloidal stability of latex after irradiation caused by radiolytic species absorption that promotes the increase of particle size. The antioxidant also contributes to reversible destabilization of gamma irradiated latex, because it is also adsorbed by particles surface. The relation between the latex viscosity and the TS of respective rubber plates is reverse, showing the latex stability affects the quality of rubber goods. (author)

  20. The entry of free radicals into polystyrene latex particles

    International Nuclear Information System (INIS)

    Adams, M.E.; Trau, M.; Gilbert, R.C.; Napper, D.R.

    1988-01-01

    Mechanistic understanding of the processes governing the kinetics of emulsion polymerization has both scientific and technical interest. One component of this process that is poorly understood at present is that of free radical entry into latex particles. Measurements were made of the entry rate coefficient as a function of temperature for free radicals entering polystyrene latex particles in seeded emulsion polymerizations initiated by γ-rays. The activation energy for entry was found to be less than 24 ± 3 kJ mol -1 , consistent with entry being controlled by a physical (e.g. diffusional) rather than a chemical process. Measurement of the entry rate coefficient as a function of the γ-ray dose rate suggested that the factors that determine the entry rate when the primary free radicals are uncharged are similar to those that determine the entry rate for charged free radicals derived from chemical initiation by peroxydisulfate. This result was consistent with measurements of the entry rate coefficient of charged free radicals derived from peroxydisulfate; these data were found to be virtually independent of both the extent of the latex surface coverage by the anionic surfactant sodium dodecyl sulfate and the ionic strength of the continuous phase. The data refute several proposals given in the literature for the rate-determining step for entry, being inconsistent with control by collision of free radicals with the latex particles, surfactant desorption, and an electrostatic barrier arising from the colloidal nature of the entering free radical. The origin of the activation energy for entry remains obscure

  1. Osmotic de-swelling and swelling of latex dispersions

    International Nuclear Information System (INIS)

    Bonnet-Gonnet, Cecile

    1993-01-01

    This research thesis reports the comparison of, on the one hand, direct measurements of de-swelling resistance of latex dispersions obtained by osmotic pressure with, on the other hand, predictions made by models of electrostatic interactions. This resistance is explained in the case of sulphate-stabilised polystyrene particles (direct repulsion between charged particles), and in the case of copolymer (ps-pba) particles covered by an amphiphilic polymer (interactions between surface macromolecules and polymers). The study of de-swelling and swelling cycles highlights the existence of thresholds beyond which the concentrated dispersion has some cohesion. This irreversibility can be modelled by a Van der Waals attraction. The role of hydrophobic forces in latex destabilisation is studied [fr

  2. Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

    International Nuclear Information System (INIS)

    Määttänen, Anni; Ihalainen, Petri; Törngren, Björn; Rosqvist, Emil; Pesonen, Markus; Peltonen, Jouko

    2016-01-01

    Graphical abstract: - Highlights: • Transparent self-supported latex films were fabricated by a peel-off process. • Various template substrates were used for creating e.g. hierarchically structured latex films. • Ultra-thin and semi-transparent conductive gold electrodes were evaporated on the latex films.Electrochemical experiments were carried out to verify the applicability of the electrodes. - Abstract: Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV–vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH_2)_1_1OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal (optical and

  3. Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

    Energy Technology Data Exchange (ETDEWEB)

    Määttänen, Anni, E-mail: anni.maattanen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Ihalainen, Petri, E-mail: petri.ihalainen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Törngren, Björn, E-mail: bjorn.torngren@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Rosqvist, Emil, E-mail: emil.rosqvist@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Pesonen, Markus, E-mail: markus.pesonen@abo.fi [Physics, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Peltonen, Jouko, E-mail: jouko.peltonen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland)

    2016-02-28

    Graphical abstract: - Highlights: • Transparent self-supported latex films were fabricated by a peel-off process. • Various template substrates were used for creating e.g. hierarchically structured latex films. • Ultra-thin and semi-transparent conductive gold electrodes were evaporated on the latex films.Electrochemical experiments were carried out to verify the applicability of the electrodes. - Abstract: Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV–vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH{sub 2}){sub 11}OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal

  4. Anticancer activity of flavonol and flavan-3-ol rich extracts from Croton celtidifolius latex.

    Science.gov (United States)

    Biscaro, Fernanda; Parisotto, Eduardo Benedetti; Zanette, Vanilde Citadini; Günther, Tania Mara Fischer; Ferreira, Eduardo Antonio; Gris, Eliana Fortes; Correia, João Francisco Gomes; Pich, Claus Tröger; Mattivi, Fulvio; Filho, Danilo Wilhelm; Pedrosa, Rozangela Curi

    2013-06-01

    Croton celtidifolius Baill (Euphorbiaceae) is a tree found in the Atlantic Forest in Southern Brazil, where it is commonly known as "Sangue-de-Dragão". Its red latex is used traditionally for treating ulcers, diabetes and cancer. To evaluate antitumor activities of Croton celtififolius latex in vitro and in vivo. Phytochemical analyses were conducted using HPLC-DAD-MS. Cytotoxic, nuclease and pro-apoptotic properties were determined using the tetrazolium salt assay (MTT), plasmid DNA damage assay and ethidium bromide (EB)/acridine orange methods, respectively, and antitumor activity was determined in the Ehrlich ascites carcinoma (EAC) mouse model. Phytochemical studies indicated a high phenol content of flavonols (45.67 ± 0.24 and 18.01 ± 0.23 mg/mL of myricetin and quercetin, respectively) and flavan-3-ols (114.12 ± 1.84 and 1527.41 ± 16.42 mg/L of epicatechin and epigallocatechin, respectively) in latex. These compounds reduced MCF-7 and EAC cell viability in the MTT assay (IC50 = 169.0 ± 1.8 and 187.0 ± 2.2 μg/mL, respectively). Latex compounds caused significant DNA fragmentation and increased the number of apoptotic cells (negative control (NC), 12%; latex, 41%) as indicated by differential staining in the EB/acridine orange assay. The in vivo latex treatment at 3.12 mg/kg/day reduced the body weight by 7.57 ± 2.04 g and increased median survival time to 17.5 days when compared to the NC group (13.0 days). In addition, the highest latex concentration inhibited tumor growth by 56%. These results agree with ethno-pharmacological reports showing cytotoxicity and antitumor activity of C. celtidifolius latex. The mechanism of antitumor action may be related to direct DNA fragmentation that reduces survival and induces apoptosis.

  5. The effect of emulsifier on the stability of irradiated LA-TZ latex

    International Nuclear Information System (INIS)

    Made Sumarti K; Utama, Marga; Puspitasari, Tita

    1998-01-01

    The effect of six kinds of stabilizer on the stability of the concentrated LA-TZ latex which contains n-BA have been studied. The six stabilizers are: 1. Naphthalene sulfonic acid formaldehyde condensate, 2. Sodium dialkyl sulfosuccinate, 3. Triethanol amine lauryl sulfate, 4. Sodium polyoxyethylene alkyl phenol ether sulfate, 5. Dodecyl benzene sulfonic acid (Neopelex FS), and 6. Ammonium laurat. The concentrations of the stabilizers are in the range of 0,1 to 0,3% and of the n-BA is 5phr (per hundred rubber). The field natural rubber latex was stabilized by Tetramethyl tiuram disulfide - Zine oxide (TMTD-ZnO) and ammonium gas, and was concentrated by centrifuge. The obtain concentrated LA-TZ latex was added by the n-BA and was kept with various storage time i.e. o, 2, 4, 6, 18, and 24 hours. It was found that the stable latex was irradiated by 15 kGy dose and the physical properties was tested, then the maximum tensile strength of 223,3 kg/cm 2 was found on Neopelex FS concentrate at 0,1%. (authors)

  6. Elements of the LaTeX system for the development of large publications

    DEFF Research Database (Denmark)

    Andersen, Esben Sloth

    This document presents gives a quick overview over the LATEX system from the viewpoint of the production of books and complex papers. Thereby it provides the starting point for the author's selection of a set of LATEX packages and the development of related commands....

  7. Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

    Directory of Open Access Journals (Sweden)

    H Nabavizade

    2007-07-01

    Full Text Available Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descriptive study five hundred eighty operation room staff of ten private and state hospitals in Shiraz completed latex allergy questionnaire. They were questioned about personal history and previous history of latex sensitivity, symptoms of latex reactivity and about other allergies particularly to foods that may cross react with latex. Informed consent was obtained and skin prick testing was performed with natural rubber latex. Skin prick tests were done with three potentially cross reacting food (banana, Kiwi, and potato. The obtained data were analyzed with SPSS software and Chi-square test. Results: Among the 580 operation room workers 104 (17.9 % of participants were positive to latex skin test. We found a significant association between positive skin test to latex in operation room staff and atopy, urticaria and food allergy. Positive skin test to latex related to positive kiwi skin test (p<0.05. The prevalence did not vary by sex, age, education, surgical and non surgical glove users, history of contact dermatitis or smoking status. Conclusion: Latex allergy has a high prevalence in personnel of operation room. Evaluation of present symptom and prediction of future disease necessitate screening test in individuals at risk.

  8. Evaluation of apparent viscosity of Para rubber latex by diffuse reflection near-infrared spectroscopy.

    Science.gov (United States)

    Sirisomboon, Panmanas; Chowbankrang, Rawiphan; Williams, Phil

    2012-05-01

    Near-infrared spectroscopy in diffuse reflection mode was used to evaluate the apparent viscosity of Para rubber field latex and concentrated latex over the wavelength range of 1100 to 2500 nm, using partial least square regression (PLSR). The model with ten principal components (PCs) developed using the raw spectra accurately predicted the apparent viscosity with correlation coefficient (r), standard error of prediction (SEP), and bias of 0.974, 8.6 cP, and -0.4 cP, respectively. The ratio of the SEP to the standard deviation (RPD) and the ratio of the SEP to the range (RER) for the prediction were 4.4 and 16.7, respectively. Therefore, the model can be used for measurement of the apparent viscosity of field latex and concentrated latex in quality assurance and process control in the factory.

  9. Glove powder's carrying capacity for latex protein: analysis using the ASTM ELISA test.

    Science.gov (United States)

    Beezhold, D; Horton, K; Hickey, V; Daddona, J; Kostyal, D

    2003-01-01

    Glove donning powders carry latex proteins and disperse them into the workplace environment. We have used the ASTM D6499 ELISA to quantify the amount of latex antigen bound to and carried by glove powders. We could differentiate between a small amount of protein actually bound to the powders and a larger amount carried by the powder. Enhanced binding of a major allergen, Hev b 5, to the starch powders was demonstrated by Western blot. The D6499 ELISA is able to measure total latex antigen, soluble and powder bound, simultaneously without the need to centrifuge the samples.

  10. Road-surface properties affecting rates of energy dissipation from vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Igwe, E.A. [Department of Civil Engineering, Rivers State University of Science and Technology, Port Harcourt, P.M.B 5080, Rivers State (Nigeria); Ayotamuno, M.J.; Okparanma, R.N. [Department of Agricultural and Environmental Engineering, Rivers State University of Science and Technology, Port Harcourt, P.M.B 5080, Rivers State (Nigeria); Ogaji, S.O.T.; Probert, S.D. [School of Engineering, Cranfield University, Bedfordshire Mk43 OAL (United Kingdom)

    2009-09-15

    The rates of energy that moving vehicles dissipate to road surfaces as well as noise emissions and their propensities for pitting (and hence their repair costs per year) all depend upon the structural properties of these surfaces. Thus, to increase the strength of bituminous concrete (i.e. a typical flexible road-surface) has been one of the major recent aims in highway engineering. The present study explored techniques that will increase these strength properties by modifying the material, using rubber latex, through rubberization and hence, improve the strength of the flexible trafficked surface when in contact with vehicles. At the optimal design asphalt (i.e. bitumen) content of 4.68%, the successive addition of various percentages of the rubber latex produced a design value of 1.65% rubber content, which increased the stability of the roadway from 1595 to 2639 N (i.e. an 65.5% increase) and the density from 2447 to 2520.8 kg/m{sup 3} (i.e. a 3.02% increase). This shows that the addition of rubber latex to bituminous concrete (a flexible road-surface) increased sustainability and the strength (in terms of stability and density). Similarly, the air voids and voids in the mineral aggregate (VMA) were reduced by introducing latex from 4.22% to 3.45% (i.e. a 17.06% reduction) and 16.25% to 13.43% (i.e. an 17.4% reduction), respectively. Whereas, the reduction in voidage volume added strength to the bituminous concrete by increasing its stability and density, the reduction in VMA had no positive impact on the strength properties of the flexible road-surface. (author)

  11. Analysis of Aqueous Extractable Protein in Radiation Pre vulcanized Natural Rubber Latex (RVNRL) And Sulphur Pre vulcanized Natural Rubber Latex (SVNRL)

    International Nuclear Information System (INIS)

    Sofian Ibrahim; Mohd Noor Wadi Mat Lazim; Syuhada Ramli; Keong, C.C.; Khairul Hisyam Mohd Yusof; Muhammad Saiful Omar; Najib Mohd Zakey; Hafizuddin Maseri; Noor Hasni Mohd Ali

    2015-01-01

    The use of radiation do not only produces Radiation Pre vulcanized Natural Rubber Latex (RVNRL) that can be used for the production of nitrosamines free products, moreover, RVNRL also able to exclude type IV allergy that caused by high protein content in the products. Leaching water from production of finger coat from RVNRL and Sulphur Pre vulcanized Natural rubber Latex (SVNRL) has been collected. Extractable protein content from water samples measured according to the test protocol ASTM D5712-2010. Water from leaching process of finger coat made from RVNRL showed a higher protein content than SVNRL. This explains why RVNRL based products contain very low protein content and thus reduce the risk of Type IV allergy. (author)

  12. Latex-mediated synthesis of ZnS nanoparticles: green synthesis approach

    Energy Technology Data Exchange (ETDEWEB)

    Hudlikar, Manish; Joglekar, Shreeram [University of Pune, Division of Biochemistry, Department of Chemistry (India); Dhaygude, Mayur [National Chemical Laboratory, Polymer Science and Engineering Division (India); Kodam, Kisan, E-mail: kodam@chem.unipune.ac.in [University of Pune, Division of Biochemistry, Department of Chemistry (India)

    2012-05-15

    A low-cost, green synthesis of ZnS nanoparticles is reported using 0.3 % latex solution prepared from Jatropha curcas L. ZnS nanoparticles were characterized by X-ray diffraction, selected area electron diffraction, transmission electron microscopy, energy dispersive analysis of X-rays, UV-vis optical absorption and photoluminescence techniques. Fourier Transform Infrared Spectroscopy was performed to find the role of cyclic peptides namely curcacycline A (an octapeptide), curcacycline B (a nonapeptide) and curcain (an enzyme) as a possible reducing and stabilizing agents present in the latex of J. curcas L. The average size of ZnS nanoparticles was found to be 10 nm. Latex of J. curcas L. itself acts as a source of sulphide (S{sup -2}) ions that are donated to Zn ions under present experimental conditions. Source of sulphide (S{sup -2}) ions is still unclear, but we speculate that cysteine or thiol residues present in enzyme curcain may be donating these sulphide (S{sup -2}) ions.

  13. Latex-mediated synthesis of ZnS nanoparticles: green synthesis approach

    Science.gov (United States)

    Hudlikar, Manish; Joglekar, Shreeram; Dhaygude, Mayur; Kodam, Kisan

    2012-05-01

    A low-cost, green synthesis of ZnS nanoparticles is reported using 0.3 % latex solution prepared from Jatropha curcas L. ZnS nanoparticles were characterized by X-ray diffraction, selected area electron diffraction, transmission electron microscopy, energy dispersive analysis of X-rays, UV-vis optical absorption and photoluminescence techniques. Fourier Transform Infrared Spectroscopy was performed to find the role of cyclic peptides namely curcacycline A (an octapeptide), curcacycline B (a nonapeptide) and curcain (an enzyme) as a possible reducing and stabilizing agents present in the latex of J. curcas L. The average size of ZnS nanoparticles was found to be 10 nm. Latex of J. curcas L. itself acts as a source of sulphide (S-2) ions that are donated to Zn ions under present experimental conditions. Source of sulphide (S-2) ions is still unclear, but we speculate that cysteine or thiol residues present in enzyme curcain may be donating these sulphide (S-2) ions.

  14. Latex-mediated synthesis of ZnS nanoparticles: green synthesis approach

    International Nuclear Information System (INIS)

    Hudlikar, Manish; Joglekar, Shreeram; Dhaygude, Mayur; Kodam, Kisan

    2012-01-01

    A low-cost, green synthesis of ZnS nanoparticles is reported using 0.3 % latex solution prepared from Jatropha curcas L. ZnS nanoparticles were characterized by X-ray diffraction, selected area electron diffraction, transmission electron microscopy, energy dispersive analysis of X-rays, UV–vis optical absorption and photoluminescence techniques. Fourier Transform Infrared Spectroscopy was performed to find the role of cyclic peptides namely curcacycline A (an octapeptide), curcacycline B (a nonapeptide) and curcain (an enzyme) as a possible reducing and stabilizing agents present in the latex of J. curcas L. The average size of ZnS nanoparticles was found to be 10 nm. Latex of J. curcas L. itself acts as a source of sulphide (S −2 ) ions that are donated to Zn ions under present experimental conditions. Source of sulphide (S −2 ) ions is still unclear, but we speculate that cysteine or thiol residues present in enzyme curcain may be donating these sulphide (S −2 ) ions.

  15. Latex glove sensitivity amongst diagnostic imaging healthcare ...

    African Journals Online (AJOL)

    kemrilib

    Sciences, Faculty of Health Sciences and Technology, University of Nigeria, Enugu Campus, Enugu. State, Nigeria. .... Occupation. No of .... latex protein residue and act as a hapten or .... at Work Act, 1989 and the safety, Health and Welfare at.

  16. Utilization of waste glass in translucent and photocatalytic concrete

    NARCIS (Netherlands)

    Spiesz, P.; Rouvas, S.; Brouwers, H.J.H.

    2016-01-01

    Abstract This article addresses the development of a translucent and air purifying concrete containing waste glass. The concrete composition was optimized applying the modified Andreasen & Andersen model to obtain a densely packed system of granular ingredients. Both untreated (unwashed) and washed

  17. Incidence of latex harvesting technologies on agronomic and ...

    African Journals Online (AJOL)

    Incidence of latex harvesting technologies on agronomic and physiological parameters and profitability of some rapid metabolic class clones of rubber tree ( Hevea brasiliensis ) in southwestern Côte d'Ivoire.

  18. Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

    Energy Technology Data Exchange (ETDEWEB)

    Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S, E-mail: chai@nuclearmalaysia.gov.my [Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

    2010-05-15

    Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

  19. Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

    International Nuclear Information System (INIS)

    Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S

    2010-01-01

    Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

  20. Electrically conductive polymer concrete coatings

    Science.gov (United States)

    Fontana, Jack J.; Elling, David; Reams, Walter

    1990-01-01

    A sprayable electrically conductive polymer concrete coating for vertical d overhead applications is described. The coating is permeable yet has low electrical resistivity (<10 ohm-cm), good bond strength to concrete substrates, and good weatherability. A preferred formulation contains about 60 wt % calcined coke breeze, 40 wt % vinyl ester with 3.5 wt % modified bentonite clay. Such formulations apply evenly and provide enough rigidity for vertical or overhead structures so there is no drip or sag.

  1. Concreteness Effects and Syntactic Modification in Written Composition.

    Science.gov (United States)

    Sadoski, Mark; Goetz, Ernest T.

    1998-01-01

    Investigates whether concreteness was related to a key characteristic of written composition--the cumulative sentence with a final modifier--which has been consistently associated with higher quality writing. Supports the conceptual-peg hypothesis of dual coding theory, with concrete verbs providing the pegs on which cumulative sentences are…

  2. Soybean oil in water-borne coatings and latex film formation study by AC impedance

    Science.gov (United States)

    Jiratumnukul, Nantana

    Conventional coalescing agents such as butyl cellosolve, butyl carbitol, and TexanolRTM are widely use in the latex coatings industry to facilitate film formation at ambient temperature. Coalescent aids are composed of solvents with low evaporation rates. After water evaporates, coalescent aids would help soften polymer molecules and form continuous films, then gradually evaporates from the film. Coalescent aids, therefore, are considered as volatile organic compounds (VOC), which are of environmental concern. The main purpose of this research project was to prepare a fatty acid glycol ester from soybean oil and glycol (polyols). The soybean oil glycol ester can be used as a coalescent aid in latex paint formulation. The soybean oil glycol ester not only lowered the minimum film formation temperature of latex polymers and continuous film formed at ambient temperature, but also after it has facilitated film formation, does not substantially evaporate, but becomes part of the film. Soybean oil glycol esters, therefore, can reduce the VOC levels and facilitate film formation of latex paints. In the second part of this research AC-Impedance was used to investigate the efficiency of soybean oil coalescent aid in latex film formation relative to the conventional ones. The coating resistance showed that the efficiency of film formation was increased as a function of dry time. The coating resistance also exhibited the effect of soybean oil ester in latex film formation in the same fashion as a conventional coalescent aid, TexanolRTM.

  3. Test trial radiation vulcanization of natural rubber latex in Jakarta Indonesia

    International Nuclear Information System (INIS)

    Devendra, R.; Kulatunge, S.S.; Chandralal, H.N.K.K.; Kalyani, N.M.V.; Seneviratne, J.; Wellage, S.

    1994-01-01

    Radiation vulcanization of natural rubber latex (RVNRL) can be used to make large quantities of specially stabilized latex. It is possible to obtain RVNRL films of tensile strength over 25 MPa. The films could be either coagulant dipped or cast. It is very important to determine the correct radiation dose which gives the maximum tensile strength. Cross linking density or prevulcanized relax modulus (PRM) at 100% is a reliable property to control the prevulcanization

  4. Finite element analysis of prestressed concrete reactor vessels

    International Nuclear Information System (INIS)

    Smith, P.D.; Cook, W.A.; Anderson, C.A.

    1977-01-01

    Several present and proposed gas-cooled reactors use concrete pressure vessels. In addition, concrete is almost universally used for the secondary containment structures of water-cooled reactors. Regulatory agencies must have means of assuring that these concrete structures perform their containment functions during normal operation and after extreme conditions of transient overpressure and high temperature. The NONSAP nonlinear structural analysis program has been extensively modified to provide one analytical means of assessing the safety of reinforced concrete pressure vessels and containments. Several structural analysis codes were studied to evaluate their ability to model the nonlinear static and dynamic behavior of three-dimensional structures. The NONSAP code was selected because of its availability and because of the ease with which it can be modified. In particular, the modular structure of this code allows ready addition of specialized material models. Major modifications have been the development of pre- and post-processors for mesh generation and graphics, the addition of an out-of-core solver, and the addition of constitutive models for reinforced concrete subject to either long-term or short-term loads. Emphasis was placed on development of a three-dimensional analysis capability

  5. Production Of Hollow Toy Product From Radiation Pre vulcanized Natural Rubber Latex (RVNRL) By Using Casting And Moulding Technique

    International Nuclear Information System (INIS)

    Mohd Noorwadi Mat Lazim; Sofian Ibrahim; Muhammad Saiful Omar

    2013-01-01

    Hollow toy products are very synonym to the child from the age of months since it able to stimulating each of their sense such as sight, hearing, taste, touch and smell. Most of hollow toy products are made from natural rubber latex by using moulding and casting technique. The moulding and casting technique is a manufacturing process by pored liquid latex into a mould, which contain cavity of the desired shape. The mould made from plaster of Paris able to absorbs water from latex meanwhile the presence of calcium ions from plaster of Paris will tend to diffuse into latex thus promote formation of deposit on surface of cavity mould. To improve the quality and safety of hollow toy product made from latex, Radiation Pre vulcanized Natural Rubber Latex (RVNRL) has been identified to be used because it can fulfill the standard requirement for latex and also due to its special abilities such as lower modulus (soft latex products), nitrosamines free, low in nitrosatables, free from chemical accelerators induced allergies and better biodegradability. This paper identify the problem appears from the process of making hollow toy products from RVNRL by using moulding and casting technique. (author)

  6. Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex; Estudo da biodegradabilidade e envelhecimento de filmes de borracha obtidos por processos de vulcanizacao do latex por radiacao induzida de fonte gama

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Carlos Felipe Pinto

    2005-07-01

    The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of {sup 60}C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

  7. Diagnosis of toxoplasmosis in pregnancy. Evaluation of latex-protein complexes by immnunoagglutination.

    Science.gov (United States)

    Peretti, Leandro E; Gonzalez, Verónica D G; Marcipar, Iván S; Gugliotta, Luis M

    2017-07-01

    The aim of this work was to obtain a reagent based on latex particles for ruling out acute toxoplasmosis in pregnant women by immunoagglutination (IA). Latex-protein complexes (LPC) were previously synthesized coupling the recombinant protein of Toxoplasma gondii P22Ag and the homogenate of the parasite to latex particles with different size, chemical functionality and charge density. LPC were tested in IA assays against a panel of 72 pregnant women serum samples. Results were analysed through receiver operating characteristic curves, determining area under the curve (AUC), sensitivity, specificity positive and negative predictive values (PPV and NPV, respectively). It was observed that the antigenicity of proteins was not affected during sensitization by either physical adsorption or covalent coupling. The best results in the sense of maximizing discrimination of low avidity sera from chronic ones were observed for the IA test based on latex particles with carboxyl functionality and the recombinant P22Ag, obtaining an AUC of 0·94, a sensitivity of 100% and a NPV of 100%. In this way, the proposed test could be useful for the toxoplasmosis diagnosis in pregnant women, with the advantages of being cheap, rapid and easy to be implemented.

  8. Towards anti-corrosion coatings from surfactant-free latexes based on maleic anhydride containing polymers

    NARCIS (Netherlands)

    Soer, W.J.; Ming, W.; Koning, C.E.; Benthem, van R.A.T.M.

    2008-01-01

    We report on the film formation of surfactant-free, artificial latexes based on copolymers containing maleic anhydride. Different metallic substrates, such as aluminum, steel and magnesium alloys, were coated with three different latexes. A commercial polyester based coating was used as a

  9. Latex allergy and occupational asthma in health care workers: adverse outcomes.

    OpenAIRE

    Amr, Sania; Bollinger, Mary E.

    2004-01-01

    The prevalence of natural rubber latex (NRL) allergy has been estimated to be 5-18% in health care workers, and latex exposure has been one of the leading causes of occupational asthma in the last several years. We present the cases of two nurses who developed sensitivity to NRL, both with dermatologic symptoms and respiratory symptoms that included asthma. They were referred to the University of Maryland for evaluation of their allergies, then for occupational and environmental consults. The...

  10. Radiation graft copolymerization of n-butyl acrylate on natural rubber latex

    International Nuclear Information System (INIS)

    Sundardi, F.; Kadariah, S.

    1986-01-01

    A method of radiation graft copolymerization of n-butyl acrylate (NBA) on natural rubber (NR) latex has been studied. The rate of conversion increases with the increase of NBA in latex. An irradiation dose of about 12 kGy is needed to obtain 90% conversion with 40 phr of NBA in latex. Tensile strength, tear strength, and elongation at break of grafted NR are found to decrease with increasing degree of grafting. The physical strength of a vulcanizate prepared from a mixture of NR and ply-NBA was found to be better than that of NBA-NR graft copolymer vulcanizate. The graft copolymerization reaction takes place in the outer layer of NR particles, and because the secondary bonds between poly-NBA molecules may be weaker than those between NR molecules, the existence of a poly-NBA layer in NR particles will decrease its physical strength

  11. Maillard Reaction in Natural Rubber Latex: Characterization and Physical Properties of Solid Natural Rubber

    Directory of Open Access Journals (Sweden)

    S. Montha

    2016-01-01

    Full Text Available Maillard reaction in Natural Rubber (NR latex was investigated by treating fresh NR latex with glutaraldehyde (C5H8O2 in amounts of 0, 50, 100, and 200 mmol/kg of latex. Protein cross-linking in fresh NR latex and solid NR was confirmed by using sodium dodecylsulfate polyacrylamide gel electrophoresis (SDS-PAGE and attenuated total reflection infrared (ATR-IR spectroscopy, respectively. It was found that degree of protein cross-linking in NR increased with increasing C5H8O2 concentration. Physical properties of untreated and treated NR substances in terms of gel content, initial Wallace plasticity (P0, plasticity retention index (PRI, Mooney viscosity, and tensile strength were carefully explored. Results clearly showed that the Maillard cross-linking of proteins had remarkable effect on bulk NR properties, that is, solvent resistance, hardness, resistance to oxidation, rheological behavior, and resistance to stretching out.

  12. Concrete Production Using Technogenical, Constructional and Domestic Waste

    Directory of Open Access Journals (Sweden)

    Marija Vaičienė

    2011-04-01

    Full Text Available The article describes investigations carried out by the scientists from various countries in order to improve the physical and mechanical properties of concrete. The grained rubber of tyres, modified sawdust, crushed ceramic bricks, plastic waste and remains of glass are utilised to produce concrete mixtures. The results of research conducted by the scientists show that in the process of producing concrete we can use different types of waste to change natural aggregates and to get concrete with specific properties. Currently, waste handling and utilization are burning ecological problems. Therefore, intensive investigations are carried out in order to utilise technogenical, constructional and domestic waste for concrete mixtures. Article in Lithuanian

  13. Evaluation of peptides release using a natural rubber latex biomembrane as a carrier.

    Science.gov (United States)

    Miranda, M C R; Borges, F A; Barros, N R; Santos Filho, N A; Mendonça, R J; Herculano, R D; Cilli, E M

    2018-05-01

    The biomembrane natural (NRL-Natural Rubber Latex), manipulated from the latex obtained from the rubber tree Hevea brasiliensis, has shown great potential for application in biomedicine and biomaterials. Reflecting the biocompatibility and low bounce rate of this material, NRL has been used as a physical barrier to infectious agents and for the controlled release of drugs and extracts. The aim of the present study was to evaluate the incorporation and release of peptides using a latex biomembrane carrier. After incorporation, the release of material from the membrane was observed using spectrophotometry. Analyses using HPLC and mass spectroscopy did not confirm the release of the antimicrobial peptide [W 6 ]Hylin a1 after 24 h. In addition, analysis of the release solution showed new compounds, indicating the degradation of the peptide by enzymes contained in the latex. Additionally, the release of a peptide with a shorter sequence (Ac-WAAAA) was evaluated, and degradation was not observed. These results showed that the use of NRL as solid matrices as delivery systems of peptide are sequence dependent and could to be evaluated for each sequence.

  14. Frequent IgE sensitization to latex, cow's milk, and egg in children with short bowel syndrome.

    Science.gov (United States)

    Mazon, Angel; Solera, Eva; Alentado, Noemi; Oliver, Fernando; Pamies, Rafael; Caballero, Luis; Nieto, Antonio; Dalmau, Jaime

    2008-03-01

    Children with short bowel syndrome (SBS) undergo frequent operations, so they are at risk for sensitizing to latex. There have been isolated reports of sensitization to food in these children. In a cross-sectional study, we assessed sensitization to latex, cow's milk, and egg with skin prick tests (SPT) and serum-specific immunoglobulin E (IgE) in 14 children with SBS. Data were collected about the number of operations with latex devices, serum total IgE, and history of feeding with milk formula. Ten children were sensitized to latex (specific IgE median: 6.7 kU/l, range: 0.5-33). Compared with those non-sensitized, sensitized children had significantly (p range: 0.5-21.1 kU/l), and five to egg (specific IgE median: 0.68, range: 0.58-2.17 kU/l). Except for some isolated days with cow's milk formula, the children had been initially fed with a diet without intact cow's milk proteins. Sensitization to latex, cow's milk, and egg is very frequent in children with SBS. They should be treated in a latex-free environment since the very early stages of the disease, and should be routinely studied regarding food sensitization, as this might contribute as an added factor in the chronic diarrhea of these patients.

  15. The evolution and use of a personal LaTeX metapackage

    DEFF Research Database (Denmark)

    Andersen, Esben Sloth

    This document defines and describes esameta.sty and its variant esametaps.sty. They are personal LATEX packages that largely consist of calls of other packages. These 'metapackages' are selected to help the development of the author's complex book and paper projects-but some of his decisions migh...... be of more general relevance. The use of the LATEX system of 'literate programming' and the testing the compatibility of new commands and packages with the previously included parts of the metapackage should also be noticed....

  16. Residual monomer reduction in polymer latex products by extraction with supercritical carbon dioxide

    NARCIS (Netherlands)

    Aerts, M.; Meuldijk, J.; Kemmere, M.F.; Keurentjes, J.T.F.

    2011-01-01

    Extraction of residual monomer from a latex product with supercritical carbon dioxide ((sc)CO2) in a column was studied. Operating conditions were chosen at 35¿°C and 100 bar. For reducing the residual styrene level in a polystyrene latex from 104 ppm to 100¿ppm and from 104 ppm to 10¿ppm, a

  17. Incidence of latex harvesting technologies on agronomic and ...

    African Journals Online (AJOL)

    parameters and profitability of some rapid metabolic class clones of rubber ... of hormonal stimulation had no negative influence on the vegetative growth ..... yield (2597) was obtained with the control ..... metabolic energy of latex vessels as.

  18. Latex allergy: new insights to explain different sensitization profiles in different risk groups.

    Science.gov (United States)

    Peixinho, C; Tavares-Ratado, P; Tomás, M R; Taborda-Barata, L; Tomaz, C T

    2008-07-01

    Differences in latex allergen sensitization profiles have been described between children subjected to repetitive surgical interventions and health care workers (HCW). 'Major' allergens for patients with spina bifida are Hev b 1, 3 and 7, while for HCW, 'major' allergens are Hev b 2, 5, 6.01 and 13. The reason for these differential sensitization profiles is currently unknown. To investigate latex allergen profiles on internal and external surfaces of natural rubber latex gloves. Eighty-two samples of commonly used surgical gloves (41 glove brands) were used for analysis. Specific allergen levels of Hev b 1, 3, 5 and 6.02 on both surfaces of the gloves were quantified using an enzyme immunometric assay, a FITkit (FIT Biotech, Tampere, Finland). Differences in allergen levels were observed between internal and external surfaces of all glove types. Concentrations of Hev b 1 and Hev b 3 were significantly higher on external surfaces, while internal surfaces had higher allergen levels of Hev b 5 and Hev b 6.02. Analysis of surgical and examination gloves, powdered and nonpowdered gloves also showed that the content of Hev b 5 and Hev b 6.02 was significantly higher on internal surfaces while that of Hev b 1 and Hev b 3 was higher on external surfaces. Our study showed different allergen profiles on internal and external surfaces of natural rubber latex gloves. These results may suggest a relationship between latex allergen localization and sensitization routes in different risk groups.

  19. Changes in chemical permeation of disposable latex, nitrile, and vinyl gloves exposed to simulated movement.

    Science.gov (United States)

    Phalen, Robert N; Le, Thi; Wong, Weng Kee

    2014-01-01

    Glove movement can affect chemical permeation of organic compounds through polymer glove products. However, conflicting reports make it difficult to compare the effects of movement on chemical permeation through commonly available glove types. The aim of this study was to evaluate the effect of movement on chemical permeation of an organic solvent through disposable latex, nitrile, and vinyl gloves. Simulated whole-glove permeation testing was conducted using ethyl alcohol and a previously designed permeation test system. With exposure to movement, a significant decrease (p ≤ 0.001) in breakthrough time (BT) was observed for the latex (-23%) and nitrile gloves (-31%). With exposure to movement, only the nitrile glove exhibited a significant increase (p ≤ 0.001) in steady-state permeation rate (+47%) and cumulative permeation at 30 min (+111%). Even though the nitrile glove provided optimum chemical resistance against ethyl alcohol, it was most affected by movement. With exposure to movement, the latex glove was an equivalent option for overall worker protection, because it was less affected by movement and the permeation rate was lower than that of the nitrile glove. In contrast, the vinyl glove was the least affected by movement, but did not provide adequate chemical resistance to ethyl alcohol in comparison with the nitrile and latex gloves. Glove selection should take movement and polymer type into account. Some glove polymer types are less affected by movement, most notably the latex glove in this test. With nitrile gloves, at least a factor of three should be used when attempting to assign a protection factor when repetitive hand motions are anticipated. Ultimately, the latex gloves outperformed nitrile and vinyl in these tests, which evaluated the effect of movement on chemical permeation. Future research should aim to resolve some of the observed discrepancies in test results with latex and vinyl gloves.

  20. Prevalence of manufacturing defects in latex examination gloves used in selected dental practices in central Saudi Arabia.

    Science.gov (United States)

    Al-Swuailem, Abdullah S

    2014-07-01

    To assess the defect rates in latex examination gloves used in selected dental practices in Riyadh, Saudi Arabia. In this cross-sectional study, a total of 796 latex examination gloves were collected from 5 governmental hospitals and 5 private dental practices between April 2012 and May 2012. The gloves were assessed for presence of defects visually (VT) and using water inflation test (WIT). One and 2 sample t-tests were used to assess significant differences in defect rates among each latex brand, and between governmental hospitals and private dental practices. Defects in latex gloves were more likely to be identified using WIT compared with VT (20.2% versus 4.3%, p=0.000). Using WIT, examined latex gloves had a defect rate approximately 8 times the acceptable quality level of 2.5% (20.2%, p=0.000). Using WIT, gloves used in private dental practices had significantly higher defect rates compared with governmental dental clinics (25.6% versus 14.6%, p=0.006). Most latex examination gloves used in the sampled governmental dental clinics and private dental practices in Riyadh had significantly higher preexisting defect rates than acceptable standard levels.

  1. Comparative evaluation of Type 1 latex hypersensitivity in patients with chronic urticaria, rubber factory workers and healthy control subjects

    NARCIS (Netherlands)

    Piskin, Gamze; Akyol, Aynur; Uzar, Hatice; Tulek, Necla; Boyvat, Ayse; Gurgey, Erbak

    2003-01-01

    Latex hypersensitivity manifests itself most commonly with contact urticaria. In this study, we investigated the frequency of latex hypersensitivity as a possible aetiological factor in patients with chronic urticaria (CU) and compared latex hypersensitivity of CU patients (n = 50) with that of

  2. Shear behaviour of reinforced phyllite concrete beams

    International Nuclear Information System (INIS)

    Adom-Asamoah, Mark; Owusu Afrifa, Russell

    2013-01-01

    Highlights: ► Phyllite concrete beams often exhibited shear with anchorage bond failure. ► Different shear design provisions for reinforced phyllite beams are compared. ► Predicted shear capacity of phyllite beams must be modified by a reduction factor. -- Abstract: The shear behaviour of concrete beams made from phyllite aggregates subjected to monotonic and cyclic loading is reported. First diagonal shear crack load of beams with and without shear reinforcement was between 42–58% and 42–92% of the failure loads respectively. The phyllite concrete beams without shear links had lower post-diagonal cracking shear resistance compared to corresponding phyllite beams with shear links. As a result of hysteretic energy dissipation, limited cyclic loading affected the stiffness, strength and deformation of the phyllite beams with shear reinforcement. Generally, beams with and without shear reinforcement showed anchorage bond failure in addition to the shear failure due to high stress concentration near the supports. The ACI, BS and EC codes are conservative for the prediction of phyllite concrete beams without shear reinforcement but they all overestimate the shear strength of phyllite concrete beams with shear reinforcement. It is recommended that the predicted shear capacity of phyllite beams reinforced with steel stirrups be modified by a reduction factor of 0.7 in order to specify a high enough safety factor on their ultimate strength. It is also recommended that susceptibility of phyllite concrete beams to undergo anchorage bond failure is averted in design by the provision of greater anchorage lengths than usually permitted.

  3. Controlling adsorption of albumin with hyaluronan on silica surfaces and sulfonated latex particles.

    Science.gov (United States)

    Berts, Ida; Fragneto, Giovanna; Porcar, Lionel; Hellsing, Maja S; Rennie, Adrian R

    2017-10-15

    Polysaccharides are known to modify binding of proteins at interfaces and this paper describes studies of these interactions and how they are modified by pH. Specifically, the adsorption of human serum albumin on to polystyrene latex and to silica is described, focusing on how this is affected by hyaluronan. Experiments were designed to test how such binding might be modified under relevant physiological conditions. Changes in adsorption of albumin alone and the co-adsorption of albumin and hyaluronan are driven by electrostatic interactions. Multilayer binding is found to be regulated by the pH of the solution and the molecular mass and concentration of hyaluronan. Highest adsorption was observed at pH below 4.8 and for low molecular mass hyaluronan (≤150kDa) at concentrations above 2mgml -1 . On silica with grafted hyaluronan, albumin absorption is reversed by changes in solvent pH due to their strong electrostatic attraction. Albumin physisorbed on silica surfaces is also rinsed away with dilute hyaluronan solution at pH 4.8. The results demonstrate that the protein adsorption can be controlled both by changes of pH and by interaction with other biological macromolecules. Copyright © 2017 Elsevier Inc. All rights reserved.

  4. Extractable protein of radiation vulcanized natural rubber latex

    International Nuclear Information System (INIS)

    Soebianto, Y.S.; Upul, R.M.; Makuuchi, K.; Yoshii, F.; Kume, T.

    2000-01-01

    A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

  5. Extractable protein of radiation vulcanized natural rubber latex

    Energy Technology Data Exchange (ETDEWEB)

    Soebianto, Y.S. [Center for Research and Development of Isotopes and Radiation Technology, BATAN, Jakarta (Indonesia); Upul, R.M. [Rubber Research Institute of Sri Lanka, Ratmalana (Sri Lanka); Makuuchi, K.; Yoshii, F.; Kume, T. [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2000-03-01

    A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

  6. Nuclear Power Plant Concrete Structures

    Energy Technology Data Exchange (ETDEWEB)

    Basu, Prabir [International Atomic Energy Agency (IAEA); Labbe, Pierre [Electricity of France (EDF); Naus, Dan [Oak Ridge National Laboratory (ORNL)

    2013-01-01

    A nuclear power plant (NPP) involves complex engineering structures that are significant items of the structures, systems and components (SSC) important to the safe and reliable operation of the NPP. Concrete is the commonly used civil engineering construction material in the nuclear industry because of a number of advantageous properties. The NPP concrete structures underwent a great degree of evolution, since the commissioning of first NPP in early 1960. The increasing concern with time related to safety of the public and environment, and degradation of concrete structures due to ageing related phenomena are the driving forces for such evolution. The concrete technology underwent rapid development with the advent of chemical admixtures of plasticizer/super plasticizer category as well as viscosity modifiers and mineral admixtures like fly ash and silica fume. Application of high performance concrete (HPC) developed with chemical and mineral admixtures has been witnessed in the construction of NPP structures. Along with the beneficial effect, the use of admixtures in concrete has posed a number of challenges as well in design and construction. This along with the prospect of continuing operation beyond design life, especially after 60 years, the impact of extreme natural events ( as in the case of Fukushima NPP accident) and human induced events (e.g. commercial aircraft crash like the event of September 11th 2001) has led to further development in the area of NPP concrete structures. The present paper aims at providing an account of evolution of NPP concrete structures in last two decades by summarizing the development in the areas of concrete technology, design methodology and construction techniques, maintenance and ageing management of concrete structures.

  7. NR based curred latex material reclaimed with 2,2'-dibenzamidodiphenyldisulphide in truck tyre tread compound

    NARCIS (Netherlands)

    Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

    2006-01-01

    It is observed that reclamation of natural rubber latex based rubber using 2,2'-dibenzamidodiphenyldisulphide as reclaiming agent is an optional methodology for recycling of waste latex rubber (WLR). For progressive replacement of virgin natural rubber by the reclaim, two alternatives curing system

  8. Surface treated polypropylene (PP) fibres for reinforced concrete

    Energy Technology Data Exchange (ETDEWEB)

    López-Buendía, Angel M., E-mail: buendia@uv.es [AIDICO Technological Institute of Construction, Benjamin Franklin 17, 46380 Paterna, Valencia (Spain); Romero-Sánchez, María Dolores [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain); Climent, Verónica [Lafarge Cementos, Polígono Sepes, Isaac Newton s/n, 46500 Sagunto, Valencia (Spain); Guillem, Celia [AIDICO Technological Institute of Construction, Marble Technical Unit, Camí de Castella 4, 03660 Novelda. Alicante (Spain)

    2013-12-15

    Surface treatments on a polypropylene (PP) fibre have contributed to the improvement of fibre/concrete adhesion in fibre-reinforced concrete. The treatments to the PP fibre were characterized by contact angle measurements, ATR-IR and XPS to analyse chemical alterations. The surface topography and fibre/concrete interaction were analysed by several microscopic techniques, namely optical petrographic, and scanning electron microscopy. Treatment modified the surface chemistry and topography of the fibre by introducing sodium moieties and created additional fibre surface roughness. Modifications in the fibre surface led to an increase in the adhesion properties between the treated fibres and concrete and an improvement in the mechanical properties of the fibre-reinforced concrete composite as compared to the concrete containing untreated PP fibres. Compatibility with the concrete and increased roughness and mineral surface was also improved by nucleated portlandite and ettringite mineral association anchored on the alkaline PP fibre surface, which is induced during treatment.

  9. Latex agglutination test (LAT) for the diagnosis of typhoid fever.

    Science.gov (United States)

    Sahni, Gopal Shankar

    2013-06-01

    The efficacy of latex agglutination test in the rapid diagnosis of typhoid fever was studied and the result compared with that of blood culture. This study included 80 children suffering from typhoid fever, among which 40 were confirmed by blood culture isolation and 40 had possible typhoid fever based on high Widal's titre (a four-fold rise in the titre of antibody to typhi "O" and "H" antigen was considered as a positive Widal's test result). Eighty children, 40 with febrile illness confirmed to be other than typhoid and 40 normal healthy children were used as negative controls. The various groups were: (i) Study group ie, group I had 40 children confirmed by culture isolation of Salmonella typhi(confirmed typhoid cases). (ii) Control groups ie, (a) group II with 40 febrile controls selected from paediatrics ward where cause other than S typhi has been established, (b) group III with 40 afebrile healthy controls that were siblings of the children admitted in paediatric ward for any reason with no history of fever and TAB vaccination in the last one year, and (c) group IV with 40 children with high Widal's titre in paired sera sample. Widal's test with paired sera with a one week interval between collections were done in all 40 patients. Latex aggtutination test which could detect 900 ng/ml of antigen as observed in checker board titration, was positive in all 40 children from group I who had positive blood culture and in 30 children from group IV who had culture negative and had high Widal's titre positive. Latex agglutination test was positive in 4 children in group II and none in group III. Using blood culture positive cases as true positive and children in groups II and III as true negative, the test had a sensitivity of 100% and specificity of 96%. Latex agglutination test was found to be significantly sensitive (100%) and specific (96%) and could detect 75% more cases in group IV (possible typhoid cases). Thus latex agglutination test can be used for rapid

  10. Minimizing surgical skin incision scars with a latex surgical glove.

    Science.gov (United States)

    Han, So-Eun; Ryoo, Suk-Tae; Lim, So Young; Pyon, Jai-Kyung; Bang, Sa-Ik; Oh, Kap-Sung; Mun, Goo-Hyun

    2013-04-01

    The current trend in minimally invasive surgery is to make a small surgical incision. However, the excessive tensile stress applied by the retractors to the skin surrounding the incision often results in a long wound healing time and extensive scarring. To minimize these types of wound problems, the authors evaluated a simple and cost-effective method to minimize surgical incision scars based on the use of a latex surgical glove. The tunnel-shaped part of a powder-free latex surgical glove was applied to the incision and the dissection plane. It was fixed to the full layer of the dissection plane with sutures. The glove on the skin surface then was sealed with Ioban (3 M Health Care, St. Paul, MN, USA) to prevent movement. The operation proceeded as usual, with the retractor running through the tunnel of the latex glove. It was possible to complete the operation without any disturbance of the visual field by the surgical glove, and the glove was neither torn nor separated by the retractors. The retractors caused traction and friction during the operation, but the extent of damage to the postoperative skin incision margin was remarkably less than when the operation was performed without a glove. This simple and cost-effective method is based on the use of a latex surgical glove to protect the surgical skin incision site and improve the appearance of the postoperative scar. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

  11. Gamma irradiator design concepts for radiation vulcanisation of natural rubber latex

    International Nuclear Information System (INIS)

    Aggarwal, K.S.; Muralidharan, P.; Apte, M.G.; Kalurkar, A.R.; Shah, B.M.

    1990-01-01

    Radiation vulcanisation of natural rubber latex (NRL) is a new and yet unproven technology and one which involves undefined problems of consumer acceptance and high degree of radiation risk. Therefore, the designer should take care that the initial capital cost of the plant is as low as possible to keep the unit processing cost low during the initial lean period of the product requirement by the market. Three irradiators to process natural rubber latex have been designed as per capacity requirement of the user. Their salient features are described. (author). 2 tabs., 24 figs

  12. Status RVNRL in German latex industry and its introduction to the European market

    International Nuclear Information System (INIS)

    Bez, W.

    1996-01-01

    Reasons to look for an alternative crosslinking system avoiding sulphur curing was the restrictive policy of the German Health Authorities concerning nitrosamines. It was concluded that radiation curing offers further advantages . By avoiding the accelerators, type IV allergy is excluded, cytotoxicity is minimised to a very low level, films have better clarity and when thoroughly leached higher electrical resistance. Treatment of waste give no SO sub 2 emissions by burning, no Zinc in the ashes and possibly better microbial degradation. A development was carried out to irradiate natural latex by electron beam with a Dynamitron equipment. It was found trimethylolpropanetrimethacrylate to be a suitable sensitizer. Because of to high prices this development was interrupted. For future application trials and efforts to introduce RVNRL in the market gamma ray radiated natural latex either from Batan, Indonesia or MINT, Malaysia are used. Mainly dipped goods were produce, but radiated natural latex has shown good results in other processes. During discussions with customers it has proved necessary to establish specifications for RVNRL. A serious problem using natural latex for the production of medical devices is the type I allergy. Attempts are made to dip surgical gloves, leach them thoroughly and control extractable proteins were reduced to the very low level of 6.5 μg/g. Out of 18 patients sensitive to natural latex protein wearing gloves made from RVNRL only six have shown a positive response. That means RVNRL could help to solve the protein allergy problem. Further developments on this line are scheduled

  13. Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

    OpenAIRE

    H Nabavizade; R Amin

    2007-01-01

    Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descr...

  14. CHEMICAL EXAMINATION OF JACK TREE LATEX AND

    Indian Academy of Sciences (India)

    and on Saponification yielded fatty acids, Volatile as well as non-volatile. The unsaponifiable portion on repeated crystallisation provided a crystal- line, sharp melting compound which was identified as artostenone? from a. Latex (200 c.c.). ത്ത min- pe. Coagulum (A) Aqueous alcoholic solution (B). Acetone or ethyl acetate ...

  15. Efficacy of protection by latex gloves during orthodontic therapy.

    Science.gov (United States)

    Doll, G M; Zentner, A; Balan, R; Sergl, H G

    2000-01-01

    The wearing of gloves during orthodontic or dental treatment is generally indicated for reasons of hygiene and protection against infection. This study was aimed at determining the extent and localization of perforations caused by the various orthodontic treatment techniques and interrupting the infection barrier. The impermeability was tested by means of a water retention test according to European standard EN 455, Part 1, performed on 1600 Centramed (Centramed, Koblenz), Tekmedic and SafeEx non-sterile disposable latex gloves (both by Safe Med, Switzerland) and Safe Gan latex gloves with an additional acrylate coating (also by Safe Med). The perforation rate in unused gloves was between 0.5% and 7.5%, rising on average to 11% with increasing use. 36% of the total number of lesions resulted from handling removable appliances, and 57% from handling fixed appliances, especially when replacing arch wires and elastics. Most lesions were in the thumb, index finger and palm region. Only 18% of the defects were noticed by the dentists themselves. The gloves worn by beginners in their first year of postgraduate orthodontic training had about twice as many defects as those worn by qualified orthodontists. When patients with an increased risk of infection are to be treated, additional hand disinfection measures should be taken and 2 pairs of gloves worn in view of the relatively unreliable protection offered by commercially available latex gloves.

  16. Experimental Study on Modification of Concrete with Asphalt Admixture

    Science.gov (United States)

    Bołtryk, Michał; Małaszkiewicz, Dorota; Pawluczuk, Edyta

    2017-10-01

    Durability of engineering structures made of cement concrete with high compressive strength is a very vital issue, especially when they are exposed to different aggressive environments and dynamic loads. Concrete resistance to weathering actions and chemical attack can be improved by combined chemical and mechanical modification of concrete microstructure. Asphalt admixture in the form of asphalt paste (AP) was used for chemical modification of cement composite microstructure. Concrete structure was formed using special technology of compaction. A stand for vibro-vibropressing with regulated vibrator force and pressing force was developed. The following properties of the modified concrete were tested: compressive strength, water absorption, freeze-thaw resistance, scaling resistance in the presence of de-icing agents, chloride migration, resistance to CO2 and corrosion in aggressive solutions. Corrosion resistance was tested alternately in 1.8% solutions of NH4Cl, MgSO4, (NH2)2CO and CaCl2, which were altered every 7 days; the experiment lasted 9.5 months. Optimum compaction parameters in semi-industrial conditions were determined: ratio between piston stress (Qp ) and external top vibrator force (Po ) in the range 0.4÷-0.5 external top vibrator force 4 kN. High strength concretes with compressive strength fcm = 60÷70 MPa, very low water absorption (barrier formed in pores of cement hydrates against dioxide and chloride ions. Concrete specimens containing AP 4% c.m. and consolidated by vibro-vibropressing method proved to be practically resistant to highly corrosive environment. Vibro-vibropressing compaction technology of concrete modified with AP can be applied in prefabrication plants to produce elements for road, bridge and hydraulic engineering constructions.

  17. Assessment of the mutagenic and antimutagenic activity of Synadenium umbellatum Pax latex by micronucleus test in mice

    Directory of Open Access Journals (Sweden)

    PR. Melo-Reis

    Full Text Available Synadenium umbellatum Pax, popularly known as "cola-nota", is a medicinal plant that grows in tropical regions. The latex of this plant is used against various diseases, such as diabetes mellitus, leprosy, tripanosomiasis, leukemia, and several malignant tumors. The mutagenic, antimutagenic, and cytotoxic effects of the latex of this plant were investigated by measuring the frequency of micronuclei in mice bone marrow cells. To evaluate mutagenicity, the animals were treated with four doses of latex (10, 30, 50, and 100 mg/kg body weight. To study the antimutagenic activity, the animals were simultaneously treated with latex and mitomycin C (4 mg/kg. The cytotoxicity was evaluated by polychromatic and normochromatic erythrocytes ratio. Our results showed a significant increase of frequency of micronucleated polychromatic erythrocytes (MNPCE compared to the negative control group (p 0.05 was detected at the doses of 50 and 100 mg/kg. Under our experimental conditions, the results obtained indicate strong mutagenic and cytotoxic activity of S. umbellatum latex except the dose of 10 mg/kg and moderate antimutagenic effect at lower doses.

  18. Nanosized carbon modifier used to control plastic deformations of asphalt concrete

    Science.gov (United States)

    Vysotskaya, M. A.; Shekhovtsova, S. Yu; Barkovsky, D. V.

    2018-03-01

    Aspects related to plastic track, the formation of which directly depends on the properties of the binder in the composition of asphalt concrete, are considered in this article. The effect of primary carbon nanomaterials on the quality of polymer and bitumen binder in comparison with the traditional binder including cross-linking agent is evaluated. The influence of binders on the resistance to the track formation of type B asphalt concrete is studied. To quantify the service life of surfacing, a calculation method based on the criteria for the resistance of surfacing material to plastic deformations is used.

  19. Low Shrinkage Cement Concrete Intended for Airfield Pavements

    Science.gov (United States)

    Małgorzata, Linek

    2017-10-01

    The work concerns the issue of hardened concrete parameters improvement intended for airfield pavements. Factors which have direct or indirect influence on rheological deformation size were of particular interest. The aim of lab testing was to select concrete mixture ratio which would make hardened concrete less susceptible to influence of basic operating factors. Analyses included two research groups. External and internal factors were selected. They influence parameters of hardened cement concrete by increasing rheological deformations. Research referred to innovative cement concrete intended for airfield pavements. Due to construction operation, the research considered the influence of weather conditions and forced thermal loads intensifying concrete stress. Fresh concrete mixture parameters were tested and basic parameters of hardened concrete were defined (density, absorbability, compression strength, tensile strength). Influence of the following factors on rheological deformation value was also analysed. Based on obtained test results, it has been discovered that innovative concrete, made on the basis of modifier, which changes internal structure of concrete composite, has definitely lower values of rheological deformation. Observed changes of microstructure, in connection with reduced deformation values allowed to reach the conclusion regarding advantageous characteristic features of the newly designed cement concrete. Applying such concrete for airfield construction may contribute to extension of its operation without malfunction and the increase of its general service life.

  20. Effects of radio sensitizers in the vulcanization of natural rubber latex induced by gamma radiation

    International Nuclear Information System (INIS)

    Souza, A. de; Canavel, V.; Araujo, S.C. de; Guedes, S.M.L.

    1992-01-01

    The effect of C Cl 4 and n-butyl acrylate as a sensitizer for radiation vulcanization of 60% DRC natural rubber latex with gamma rays, was studied relating tensile strength of vulcanized latex. The vulcanization dose is 200 kGy for natural rubber latex and it decreases to 40 kGy and to 9 kGy in the presence of C Cl 4 / potassium laureate and n-butyl acrylate / t-butyl hydroperoxide, respectively. The H 2 O 2 as a co-sensitizer does not change the efficiency of the combination of these sensitizers. The IV spectra show the formation of C=O after the irradiation as consequence of oxidation reactions. (author)

  1. Optical response of a flat metallic surface coated with a monolayer array of latex spheres

    International Nuclear Information System (INIS)

    Shi Lei; Liu Xiaohan; Yin Haiwei; Zi Jian

    2010-01-01

    We report on the fabrication, characterization and simulation of a structure consisting of a flat metallic surface coated with a monolayer array of latex spheres. This structure shows interesting optical response: over flat metallic surfaces a series of reflection minima appear in reflection spectra. Numerical simulations revealed that the structure can support two types of surface modes: surface plasmon-polaritons bound at the metallic surface and guided modes confined to the array of latex spheres, or their hybrids. Both experimental and theoretical results indicated that these surface modes show well-defined band structures due to the introduced periodicity by the monolayer array of latex spheres.

  2. Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury, E-mail: jackalvesribeiro@gmail.com [Laboratorio de Engenharia e Biomaterial (BioEngLab), Faculdade Gama, Universidade de Brasilia (UnB), DF (Brazil); Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria [Universidade do Estado do Rio Grande do Norte (UERN), Mossoro, RN (Brazil)

    2017-05-15

    The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

  3. Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

    International Nuclear Information System (INIS)

    Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury; Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria

    2017-01-01

    The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

  4. Initial rheological description of high performance concretes

    Directory of Open Access Journals (Sweden)

    Alessandra Lorenzetti de Castro

    2006-12-01

    Full Text Available Concrete is defined as a composite material and, in rheological terms, it can be understood as a concentrated suspension of solid particles (aggregates in a viscous liquid (cement paste. On a macroscopic scale, concrete flows as a liquid. It is known that the rheological behavior of the concrete is close to that of a Bingham fluid and two rheological parameters regarding its description are needed: yield stress and plastic viscosity. The aim of this paper is to present the initial rheological description of high performance concretes using the modified slump test. According to the results, an increase of yield stress was observed over time, while a slight variation in plastic viscosity was noticed. The incorporation of silica fume showed changes in the rheological properties of fresh concrete. The behavior of these materials also varied with the mixing procedure employed in their production. The addition of superplasticizer meant that there was a large reduction in the mixture's yield stress, while plastic viscosity remained practically constant.

  5. Effect of rootstock on the scion of Hevea brasiliensis through metabolic analysis of latex samples by 1H NMR

    Directory of Open Access Journals (Sweden)

    Eduardo Sanches Pereira do Nascimento

    2011-01-01

    Full Text Available In this study, the effect of rootstock on grafting through metabolomic analysis of latex (Hevea brasiliensis samples was verified by 1H nuclear magnetic resonance (NMR and multivariate data analysis. Sixteen metabolites present in the latex cytosol were characterized by NMR. PCA analysis showed that the latex samples of the RR and GR groups can be differentiated. The GR group samples present a metabolic profile similar to the RR group samples, while the RG group is in an intermediate position between RR and GG groups. Sucrose and formate contributed greatly to the separation obtained by PCA, presenting a good correlation between the results. 1H NMR was an efficient technique to differentiate latex samples from different types of rootstocks and grafting and in the future could be used to predict rubber production by latex analysis.

  6. Effect of gamma radiation dose and sensitizer on the physical properties of irradiated natural rubber latex

    International Nuclear Information System (INIS)

    Komgrit, R.; Thawat, C.; B, Tripob; Wirach, T.

    2009-07-01

    Full text: The vulcanization of natural rubber latex can be induced by gamma radiation, which enhances cross-linking within the rubber matrix. The purpose of this research is to investigate the effect of gamma radiation dose and sensitizers on the physical properties of irradiated natural rubber. Three sensitizers n-butyl acrylate (n-B A), tetrachloroethylene (C 2 Cl 4 ) and trichloromethane (CHCl 3 ) were mixed with natural rubber latex before irradiation with gamma ray dose varied from 14 to 22 kGy. Results showed that the mixture of three sensitizers with specific ratios effectively induced the cross-linking of natural rubber latex. The cross-linking ratio and improved physical properties increased with increasing gamma dose. Therefore, the mixture ratios of n-B A, C 2 Cl 4 and CHCl 3 have shown to be a critical parameter in the vulcanization of natural rubber latex by gamma radiation

  7. The Synthesis and Modification of Nanosized Clickable Latex Particles

    KAUST Repository

    Almahdali, Sarah

    2013-01-01

    This research aims to add to the current knowledge available for miniemulsion polymerization reactions and to use this knowledge to synthesize multifunctional nanosized latex particles that have the potential to be used in catalysis. The physical

  8. Partial swelling of latex particles by two monomers

    NARCIS (Netherlands)

    Noel, E.F.J.; Maxwell, I.A.; German, A.L.

    1993-01-01

    The swelling of polymeric latex particles with solvent and monomer is of great importance for the emulsion polymn. process in regard to compn. drift and rate of polymn. For the monomer combination, Me acrylate-vinyl acetate, both satn. and partial swelling were detd. exptl. Theories for satn.

  9. Effect of step-wise change of stress and temperature on primary creep of concrete

    International Nuclear Information System (INIS)

    Furumura, Fukujiro; Abe, Takeo; Shinohara, Yasuji; Kim, Wha-Jung.

    1991-01-01

    The success of analyzing the behavior of concrete structures at elevated temperature greatly depends on how accurately certain mechanical properties, especially stress-strain curves, creep and thermal expansion, can be determined within wide temperature range. The importance of creep in the design of reinforced and prestressed concrete structures has been more recognized with the advent of the use of concrete at elevated temperature. The creep strain of concrete is affected by stress, time and temperature. The creep law which can predict the creep behavior under varying stress and temperature by using the experimental results of creep strain under constant stress and temperature is indispensable for analyzing the behavior of reinforced concrete structures under varying temperature. Accordingly the main purpose of this study is to clarify the primary creep behavior of concrete under varying stress and temperature. The cylindrical specimens, the testing procedure, the test results and the modified strain hardening law are reported. By using the modified strain hardening law, the primary creep behavior of concrete can be estimated better. (K.I.)

  10. Latex Imaging by Environmental STEM: Application to the Study of the Surfactant Outcome in Hybrid Alkyd/Acrylate Systems

    OpenAIRE

    Faucheu , Jenny; Chazeau , Laurent; Gauthier , Catherine; Cavaille , Jean-Yves; Goikoetxea , Monika; Minari , Roque; Asua , Jose M.

    2009-01-01

    International audience; Among other uses. latexes are a successful alternative to solvent-borne binders for coatings. Efforts are made to produce hybrid nanostructured latexes containing an acrylic phase and an alkyd phase, However, after the film-forming process, the surfactant used to stabilize these latexes remains in the film, and its location can have a drastic effect on the application properties. Among the processing parameters, the alkyd hydrophobicity can strongly influence this loca...

  11. Feasibility study of a concrete plug made of low pH concrete

    Energy Technology Data Exchange (ETDEWEB)

    Dahlstroem, Lars-Olof; Magnusson, Jonas (NCC Engineering (Sweden)); Gueorguiev, Ginko; Johansson, Morgan (Reinertsen Sverige AB, Goeteborg (Sweden))

    2009-09-15

    In this report a concrete plug, used as a barrier between the deposition tunnels and the access tunnel, is investigated. The objectives of the work is to see whether it is possible to use low pH concrete for the plug and whether it can be designed without using reinforcement. The requirements set on the plug are that the water leakage through it should be small enough and that the concrete stresses are limited to a value valid for the concrete used. A modified geometry of the plug is proposed, which makes it possible to use it as a general solution in all deposition tunnels. Material properties of a low pH concrete (B200) determined by CBI have been used. Loads considered in the study is the pressure from water and swelling, the temperature change in the rock and plug due to heat development from nuclear fuel stored in nearby copper canisters, pre-stressing in the plug due to cooling during construction and the shrinkage of concrete in the plug. Two-dimensional, axis-symmetric finite element analyses, assuming linear elastic material behaviour in rock and concrete where contact friction between concrete and rock is taken into consideration, have been used to study the structural response of the plug. A total of 48 main load combinations, consisting of 8 different load scenarios and 6 material combinations, have been used. It is found that the concrete plug will not remain uncracked when subjected to the loads studied but that it, nevertheless, is possible to achieve an unreinforced concrete plug that satisfies the requirements set up. The minimum size of the concrete compressed zone will be 0.5 m, resulting in a water leakage through the plug determined to be lower than the requirement of 0.01 l/min set up in this study. Further, the maximum compressive stresses of interest are 33 MPa and the maximum displacement in the plug is about 3 mm, which are deemed to be satisfactorily. Consequently, it is concluded that it seems possible to use low pH concrete for the plug

  12. Beta Bremsstrahlung dose in concrete shielding

    Energy Technology Data Exchange (ETDEWEB)

    Manjunatha, H.C., E-mail: manjunatha@rediffmail.com [Department of Physics, Government college for women, Kolar 563101, Karnataka (India); Chandrika, B.M. [Shravana, 592, Ist Cross, Behind St.Anne s School, PC Extension, Kolar 563101, Karnataka (India); Rudraswamy, B. [Department of Physics, Bangalore University, Bangalore 560056, Karnataka (India); Sankarshan, B.M. [Shravana, 592, Ist Cross, Behind St.Anne s School, PC Extension, Kolar 563101, Karnataka (India)

    2012-05-11

    In a nuclear reactor, beta nuclides are released during nuclear reactions. These betas interact with shielding concrete and produces external Bremsstrahlung (EB) radiation. To estimate Bremsstrahlung dose and shield efficiency in concrete, it is essential to know Bremsstrahlung distribution or spectra. The present work formulated a new method to evaluate the EB spectrum and hence Bremsstrahlung dose of beta nuclides ({sup 32}P, {sup 89}Sr, {sup 90}Sr-{sup 90}Y, {sup 90}Y, {sup 91}Y, {sup 208}Tl, {sup 210}Bi, {sup 234}Pa and {sup 40}K) in concrete. The Bremsstrahlung yield of these beta nuclides in concrete is also estimated. The Bremsstrahlung yield in concrete due to {sup 90}Sr-{sup 90}Y is higher than those of other given nuclides. This estimated spectrum is accurate because it is based on more accurate modified atomic number (Z{sub mod}) and Seltzer's data, where an electron-electron interaction is also included. Presented data in concrete provide a quick and convenient reference for radiation protection. The present methodology can be used to calculate the Bremsstrahlung dose in nuclear shielding materials. It can be quickly employed to give a first pass dose estimate prior to a more detailed experimental study. - Highlights: Black-Right-Pointing-Pointer Betas released in a nuclear reactor interact with shielding concrete and produces Bremsstrahlung. Black-Right-Pointing-Pointer The present work formulated a new method to evaluate the Bremsstrahlung spectrum and dose in concrete. Black-Right-Pointing-Pointer Presented data in concrete provide a quick and convenient reference for radiation protection.

  13. Historic Concrete : From Concrete Repair to Concrete Conservation

    NARCIS (Netherlands)

    Heinemann, H.A.

    2013-01-01

    Concrete like materials were already applied during the Roman Empire. After the decline of the Roman Empire, a wide scale application of concrete only reappeared in the 19th century. Here lies also the origin of modern (reinforced) concrete. Since then, both concrete application and composition have

  14. Production of environmentally friendly aerated concrete with required construction and operational properties

    Directory of Open Access Journals (Sweden)

    Tkach Evgeniya

    2018-01-01

    Full Text Available The purpose of these studies is to justify the feasibility of recycling different types of industrial waste instead of conventional expensive raw materials in production of environmentally friendly aerated concrete with required construction and operational properties. The impact of wastes from various industries on the environmental condition of affected areas, as well as the results of their environmental assessment were analyzed to determine whether these wastes could be used in production of high-performance building materials. The assessment of industrial wastes in aerated concrete production suggests that industrial wastes of hazard class IV can be recycled to produce aerated concrete. An environmentally friendly method for large-scale waste recycling, including a two-step environmentally sustainable mechanism, was developed. The basic quality indicators of the modified aerated concrete proved that the environmental safety could be enhanced by strengthening the structure, increasing its uniformity and improving thermal insulation properties. The modified non-autoclaved aerated concrete products with improved physical and operational properties were developed. They have the following properties: density – D700; class of concrete – B3.5; thermal transmittance coefficient – 0.143 W/(m·°C; frost resistance – F75.

  15. Pilot Scale Production of Irradiated Natural Rubber Latex and its Dipping Products

    Directory of Open Access Journals (Sweden)

    M. Utama

    2005-07-01

    Full Text Available One hundred and fifty kg natural rubber latex (NRL before and after concentration were added with 3 phr (part hundred ratio of rubber normal butyl acrylate, then the mixture were irradiated at 25 kGy by gamma rays of 60Co in pilot scale. The irradiated natural rubber latex (INRL were then being to use for producing rubber products such as condom, surgical gloves, and spygmomanometer in factory scale. The quality of INRL and rubber products such as : total solid content (TSC, dry rubber content (DRC, KOH, VFA and MST number, tensile strength, modulus, elongation at break, extractable protein content, and response against Type I allergy etc. were evaluated. The economic aspect for producing INRL by means of Gamma Irradiator (GI and Electron Beam Machine (EBM such as payback period (PP, net present value (NPV and internal rate return (IRR were calculated. The results showed that the latex properties of INRL such as DRC, TSC, KOH, VFA, and MST number are not only found to the requirement of the ISO 2004 standard but also the latex has low protein, lipid, and carbohydrate content. The physical and mechanical properties (tensile strength, modulus, and elongation at break of rubber dipping products such as condom, gloves, and sphygmomanometer are not only found to the requirement of ISO 4074, ISO 10282, and ANSI/AAMI SP-1994 standards, but also the allergic response tested clinical latex-sensitive protein allergen by ELISA test on gloves, and by SPT test on condom are found to be negative. It indicates that production of INRL or PVNRL or RVNRL by EBM 250 keV/10 mA, was more cheap than by using gamma γ irradiator 200 kCi, or sulfur vulcanization. The value of PBP (payback period was 2,1 years, NPV (net present value was 4,250 US $, PI (profitability index 1,06 and IRR (internal rate of returns was 25,0%.

  16. Radon exhalation rates of concrete modified with fly ash and silica fumes

    International Nuclear Information System (INIS)

    Amit Kumar; Chauhan, R.P.; Mehta, Vimal; Kant, K.

    2013-01-01

    The radiological impact of the environmental gas radon to the health of general public is of concern since many decades. Cement used for the construction blended with fly ash and silica fumes is recommended by Government in order to avoid the soil and environmental pollution. But these addition step-up the Indoor radon level in the dwelling due to radioactivity contents. The exhalation of radon from concrete blended with silica fumes and fly ash depends upon addition level, porosity, moisture and radioactivity content. In order to optimize the level of substitution of silica fumes and fly ash, measurements of radon exhalation rates from the concrete blended with different proportions of fly ash and silica fumes was carried out using active scintillation radon monitor. The effect of porosity, moisture, back diffusion and radioactivity content of the concrete on exhalation rates is studied. The measured exhalation rates were extrapolated for indoor radon concentration and effective dose equivalent using ICRP, 1987 recommendations. (author)

  17. Utilization of crushed clay brick in concrete industry

    Directory of Open Access Journals (Sweden)

    Ali A. Aliabdo

    2014-03-01

    Full Text Available A comprehensive experimental program regarding the use of recycled aggregates produced from demolition of brick buildings is presented. The brick wastes were crushed, sorted and classified into coarse and fine aggregates as well as powder (CBP. The first phase of the research focuses on the effect of incorporating recycled aggregates on physico-mechanical properties of paste, mortar and concrete. Non-traditional tests including X-ray diffraction (XRD, thermo-gravimetric analysis (TGA and micro-structural analysis (MSA were performed. The second phase of the program explores the effect of using recycled aggregates on properties of concrete masonry units. A total of 44 mixtures were utilized throughout the program. Results show cement paste when modified with 25% CBP achieves smaller pore size and lower weight loss under high temperature than reference paste. Furthermore, the use of recycled aggregates reduces the overall unit weight of concrete masonry units. Actually, modified concrete masonry units incorporating recycled aggregates achieve lower unit weight, higher thermal resistance and absorption rate than reference units. Although considerable strength reduction is noticeable by substitution, compressive strength levels meet the Egyptian specifications limitations. Critical replacement ratios are suggested to produce load bearing-concrete masonry units. Based on experimental evidences, it can be stated that the use of recycled aggregate and dust made of clay bricks is promising in many applications where the thermal resistance, cost and environmental aspects are imperative.

  18. Extractable protein content of radiation vulcanized natural rubber latex films

    International Nuclear Information System (INIS)

    Ma'zam Md Said; Wan Manshol Wan Zin

    1996-01-01

    The effects of processing conditions on extractable protein content of coagulant dipped radiation vulcanized natural rubber latex films have been investigated. Drying of wet-gel of radiation vulcanized latex films even at a relatively low temperature of 70 degree C resulted in increases of extractable protein content of the films. The extractable protein content is dependent upon both the temperature and time of drying of wet-gel deposit. Wet-gel leaching of film alone is not adequate to reduce the extractable protein content of films to low levels. Combination of wet-gel leaching, post-leaching, a dip in corn starch slurry, followed by drying at a low temperature of 70 degree C reduces the extractable protein content of films to very low levels

  19. [Anaphylactic reaction to latex during spinal anesthesia: a case report].

    Science.gov (United States)

    Ueda, Narumi; Kitamura, Rie; Wakamori, Takeshi; Nakamura, Kumi; Konishi, Keisuke

    2008-05-01

    A 46-year-old man, with a history of atopic dermatitis and bronchial asthma, underwent surgery for an inguinal hernia. Forty-three minutes subsequent to spinal anesthesia, the patient complained suddenly of dyspnea with wheezing. Blood pressure decreased and skin eruption was observed on his chest. Postoperative laboratory tests revealed high IgE concentration, and a skin test confirmed an allergy to latex. The patient's allergic reaction was easily overlooked because of his history of bronchial asthma and the possibility that the hypotension was caused by the high spinal anesthesia. Latex allergy should be considered in any suspicious case presenting with these symptoms during surgery. After recovery, a skin test should be used to confirm the allergy to avoid repeated allergic episodes.

  20. Radiation vulcanization of natural rubber latex using 250 keV electron beam machine

    Energy Technology Data Exchange (ETDEWEB)

    Chirinos, H.; Yoshii, F.; Makuuchi, K.; Lugao, A. E-mail: ablugao@net.ipen.br

    2003-08-01

    The sensitized radiation vulcanization of natural rubber latex has been carried out with 250 keV electrons. Latex was irradiated over a range of the beam current from 5 to 20 mA in the presence of sensitizers like the n-butyl acrylate (n-BA). The vulcanization dose decreases with increasing beam current condition. The rate of vulcanization (R{sub vul}) depends on the beam current (I) as given by the equation R{sub vul}=kI{sup 0.6}.

  1. Laboratory evaluation of a simple and rapid latex agglutination assay for the serodiagnosis of typhoid fever

    NARCIS (Netherlands)

    Abdoel, Theresia H.; Pastoor, Rob; Smits, Henk L.; Hatta, Mochammad

    2007-01-01

    A latex agglutination assay for the serodiagnosis of typhoid fever was evaluated on samples collected from patients with clinical suspicion of typhoid fever in South Sulawesi, Indonesia, where the disease is endemic. The latex assay is very easy to use, gives a rapid result and may be used as a

  2. Stress-strain curve of concretes with recycled concrete aggregates: analysis of the NBR 8522 methodology

    Directory of Open Access Journals (Sweden)

    D. A. GUJEL

    Full Text Available ABSTRACT This work analyses the methodology "A" (item A.4 employed by the Brazilian Standard ABNT 8522 (ABNT, 2008 for determining the stress-strain behavior of cylindrical specimens of concrete, presenting considerations about possible enhancements aiming it use for concretes with recycled aggregates with automatic test equipment. The methodology specified by the Brazilian Standard presents methodological issues that brings distortions in obtaining the stress-strain curve, as the use of a very limited number of sampling points and by inducing micro cracks and fluency in the elastic behavior of the material due to the use of steady stress levels in the test. The use of a base stress of 0.5 MPa is too low for modern high load test machines designed do high strength concrete test. The work presents a discussion over these subjects, and a proposal of a modified test procedure to avoid such situations.

  3. Influence of Silicon-Containing Additives on Concrete Waterproofness Property

    Science.gov (United States)

    Butakova, M. D.; Saribekyan, S. S.; Mikhaylov, A. V.

    2017-11-01

    The article studies the influence of silicon-containing additives on the property of the water resistance of concrete samples. It provides a review of the literature on common approaches and technologies improving concrete waterproofness and reinforced concrete structures. Normal hardening samples were obtained on the basis of concretes containing microsilica, aerosil or ash, or the combinations thereof. This research is aimed at the study of the complex modifier effect r on the basis of metakaolin, superplasticizer and silicon containing additives on the property of concrete water resistance. The need to use a superplasticizer to reduce the water-cement ratio and metakaolin as a hardening accelerator along with the set of strength is substantiated. This article describes a part of the results of the experiment conducted to find alternative options for colmatizing expensive additives used in the concreting foundations of private house-building. The implementation of the scientific work will not only clarify this area but will also broaden the knowledge of such additive as aerosol.

  4. Low field NMR study of the latex derived from Brosimum parinarioides - Moraceae

    International Nuclear Information System (INIS)

    Miguez, Eduardo; Tavares, Maria Ines B.

    2009-01-01

    Brosimum parinarioides is a tree found in the Amazonia forest and its latex (Leite de Amapa) is often used like food and by the popular medicine in the treatment of tuberculosis and asthma. Being swallowed in nature, its necessary determinate the stability degree of this latex in the storage conditions in which is used in Amazonia. The analyses of T 2 data showed that the limit of stability is not longer than six month in the storage conditions used by the population of Amazonia. The Low field NMR proved to be an efficient method for this kind of study. (author)

  5. New plastic plane stress model for concrete

    International Nuclear Information System (INIS)

    Winnicki, A.; Cichon, Cz.

    1993-01-01

    In the paper a description of concrete behaviour in the plane stress case is given on the basis of the modified bounding surface plasticity theory. Three independent plastic mechanisms have been introduced describing axiatoric and deviatoric plastic strains and their coupling. All the new analytical formulae for material functions being in agreement with experiments and loading/unloading criteria have been proposed. In addition, for the proper description of concrete behaviour in tension a new, separate function of bounding surface shrinkage has been introduced. (author)

  6. Isolation rubber latex binary composites consisting of cotton and poly-N, N-dimethyl-N, N-diallilammony chloride

    Directory of Open Access Journals (Sweden)

    J. Cornejo Tueros

    2012-01-01

    Full Text Available The paper discusses the application of rubber from latex binary coagulating agent consisting of cotton - textile waste and polymeric quaternary ammonium salts. The influence on the process of extracting rubber from latex flow coagulating agent temsperatury and concentration of the dispersed phase.

  7. Effect of cellulose nanocrystals from corn cob with dispersion agent polyvinyl pyrrolidone in natural rubber latex film after aging treatment

    Science.gov (United States)

    Harahap, H.; Ridha, M.; Halimatuddahliana; Taslim; Iriany

    2018-02-01

    This study about the resistance of natural rubber latex films using nanocrystals cellulose filler from corn cob waste by aging treatment. Corn cob used as organic filler composed of cellulose, hemicellulose, and lignin. Each component has a potential for reuse, such as cellulose. Cellulose from corn cob has potential application as a filler prepared by hydrolysis process using a strong acid. The producing of natural rubber latex films through coagulant dowsing process. This research started with the pre-vulcanization process of natural rubber latex at 70 °C and followed by process of vulcanization at 110 °C for 20 minutes. Natural rubber latex films that have been produced continued with the aging treatment at 70 °C for 168 hours. The mechanical properties of natural rubber latex films after aging treatment are the tensile strength, elongation at break, M100 and M300 have performed.

  8. EFFECT OF THE PHASE STRUCTURE EVOLUTION ON THE PROPERTIES OF FILMS FORMED FROM PBA/P(ST-CO-MMA)COMPOSITE LATEX

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A group of heterogeneous latexes poly(butyl acrylate)/poly(styrene-co-methyl methacrylate)(PBA/P(St-co-MMA))were prepared by a semi-continuous seeded emulsion polymerization process under monomer starved conditions.The glass transition temperature(Tg)and the mechanical properties of the film formed from the composite latex changed with the evolution of the particle morphology.A photon transmission method was used to monitor the phase structure evolution of films which were prepared from core-shell PBA/P(St-co-MMA)latex at room temperature and annealed at 383 K above Tg of the polymers.In addition,the changes of the surface of the film formed from the composite latex with time at 383 K were observed by AFM.The evidence illustrated that the film formed from the core-shell latex particles was metastable.The rearrangement of the phases could occur under proper conditions.

  9. Nitrogen removal from concentrated latex wastewater by land treatment

    Directory of Open Access Journals (Sweden)

    Vikanda Thongnuekhang

    2004-05-01

    Full Text Available Most of the concentrated latex factories in the South of Thailand discharge treated wastewater that contains high level of nitrogen to a nearby river or canals leading to a water pollution problem. A study of land treatment system was conducted to treat and utilize nitrogen in treated wastewater from the concentrated latex factory. The experimental pilot-scale land treatment system was constructed at the Faculty of Engineering, Prince of Songkla University, Hat Yai Campus. It consisted of water convolvulus (Ipomea aquatica, I. Reptans, tropical carpet grass (Axonopus compresus (Swartz Beav. and control unit (no plantation. The treated wastewater from the stabilization pond system of the selected concentrated latex factoryin Songkhla was used to irrigate each experimental unit. Influent and effluent from the experimental units were analyzed for TKN, NH3-N, Org-N, NO3 --N, NO2 --N, BOD5, sulfate, pH and EC. The land treatment system resulted a high removal efficiency for nitrogen. Tropical carpet grass provided higher removal efficiency than other units for all parameters. The removal efficiency of water convolvulus and control unit were not significantly different. The average removal efficiency of TKN, NH3-N, Org-N, BOD5 and sulfate for tropical carpet grass unit were 92, 97, 61, 88 and 52%, for water convolvulus unit were 75, 80, 43, 41 and 30%, and for control unit were 74, 80, 41, 31 and 28%, respectively. Mass balance of nitrogen transformation was conducted. It revealed that plant uptake was the major mechanism for nitrogen removal in land treatment.

  10. Characteristics of Red Algae Bioplastics/Latex Blends under Tension

    Directory of Open Access Journals (Sweden)

    M. Nizar Machmud

    2013-10-01

    Full Text Available Cassava, corn, sago and the other food crops have been commonly used as raw materials to produce green plastics. However, plastics produced from such crops cannot be tailored to fit a particular requirement due to their poor water resistance and mechanical properties. Nowadays, researchers are hence looking to get alternative raw materials from the other sustainable resources to produce plastics. Their recent published studies have reported that marine red algae, that has been already widely used as a raw material for producing biofuels, is one of the potential algae crops that can be turned into plastics. In this work, Eucheuma Cottonii, that is one of the red alga crops, was used as raw material to produce plastics by using a filtration technique. Selected latex of Artocarpus altilis and Calostropis gigantea was separately then blended with bioplastics derived from the red algae, to replace use of glycerol as plasticizer. Role of the glycerol and the selected latex on physical and mechanical properties of the red algae bioplastics obtained under a tensile test performed at room temperature are discussed. Tensile strength of some starch-based plastics collected from some recent references is also presented in this paperDoi: 10.12777/ijse.5.2.81-88 [How to cite this article: Machmud, M.N., Fahmi, R.,  Abdullah, R., and Kokarkin, C.  (2013. Characteristics of Red Algae Bioplastics/Latex Blends under Tension. International Journal of Science and Engineering, 5(2,81-88. Doi: 10.12777/ijse.5.2.81-88

  11. Tensile properties of latex paint films with TiO2 pigment

    Science.gov (United States)

    Hagan, Eric W. S.; Charalambides, Maria N.; Young, Christina T.; Learner, Thomas J. S.; Hackney, Stephen

    2009-05-01

    The tensile properties of latex paint films containing TiO2 pigment were studied with respect to temperature, strain-rate and moisture content. The purpose of performing these experiments was to assist museums in defining safe conditions for modern paintings held in collections. The glass transition temperature of latex paint binders is in close proximity to ambient temperature, resulting in high strain-rate dependence in typical exposure environments. Time dependence of modulus and failure strain is discussed in the context of time-temperature superposition, which was used to extend the experimental time scale. Nonlinear viscoelastic material models are also presented, which incorporate a Prony series with the Ogden or Neo-Hookean hyperelastic function for different TiO2 concentrations.

  12. LaTeX - Know what you are missing

    Directory of Open Access Journals (Sweden)

    Gunther Maier

    2016-11-01

    Full Text Available This article gives a brief introduction to \\LaTeX\\ and related tools. The aim is to give an overview, to demonstrate the flexibility and versatility of the software, and to assist the reader taking first steps using it. The article links to a number of valuable resources for further information.

  13. Radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Wan Manshol bin Wan Zin; Norjanah binti Mohid

    1994-01-01

    This paper describes the experimental techniques and the results of radiation vulcanization of natural rubber latex carried out on several high ammonia latices available in the country. The efficiency of various sensitisers and stabilisers used were evaluated in terms of the gamma radiation dose required to produce the maximum tensile strengths. The extent of crosslinking of RVNRL sample films were estimated by equilibrium swelling ratio measurements. The stability of pre-irradiated and post-irradiated samples were monitored using viscosity measurements as the parameter

  14. Marine bacterial prodigiosin as dye for rubber latex, polymethyl ...

    African Journals Online (AJOL)

    Prodigiosin is known for its immunomodulatory, antibacterial, antimycotic, antimalarial, algicidal and anticancer activities. Here, we reported the evaluation of prodigiosin pigment as a dyeing agent in rubber latex, paper and polymethyl methacrylate (PMMA) so that it can be considered as an alternative to synthetic pigments.

  15. Assessment of adverse reactions to latex gloves use among nurses ...

    African Journals Online (AJOL)

    ... to latex is a common problem among nurses and other health care workers. ... There was significant association between family history and occurrence of ... These effects may vary in severity from skin problems to anaphylactic shock.

  16. Investigation of Mechanism of Action of Modifying Admixtures Based on Products of Petrochemical Synthesis on Concrete Structure

    Science.gov (United States)

    Tukhareli, V. D.; Tukhareli, A. V.; Cherednichenko, T. F.

    2017-11-01

    The creation of composite materials for generating structural elements with the desired properties has always been and still remains relevant. The basis of a modern concrete technology is the creation of a high-quality artificial stone characterized by low defectiveness and structure stability. Improving the quality of concrete compositions can be achieved by using chemical admixtures from local raw materials which is a very promising task of modern materials’ science for creation of a new generation of concretes. The new generation concretes are high-tech, high-quality, multicomponent concrete mixes and compositions with admixtures that preserve the required properties in service under all operating conditions. The growing complexity of concrete caused by systemic effects that allow you to control the structure formation at all stages of the technology ensures the obtaining of composites with "directional" quality, compositions, structure and properties. The possibility to use the organic fraction of oil refining as a multifunctional hydrophobic-plasticizing admixture in the effective cement concrete is examined.

  17. Detection of latex allergens by immunoelectron microscopy in ambient air (PM10) in Oslo, Norway (1997-2003).

    Science.gov (United States)

    Namork, Ellen; Kurup, Viswanath P; Aasvang, Gunn Marit; Johansen, Bjørn V

    2004-11-01

    The authors collected ambient air along two highways in Oslo to investigate the annual variations in particulate matter (PM10) and the presence of latex as an outdoor allergen. PMI, was monitored for a period of five years, during which time the use of studded winter tires was reduced. The presence of latex and of common aeroallergens was examined directly on the collection filters with immunoelectron microscopy visualized in a scanning electron microscope. The annual variation in PM10 was similar over the five years of sampling, with increased mass concentrations in winter. Statistical analysis indicated no major effect from the change to nonstudded tires. The most important factors influencing the PM10 concentration were meteorological parameters like wind and rain. Immnunolabeling of the filters showed latex as an outdoor allergen that adhered to carbon aggregates from vehicle emission. The results also indicated cross-reactive epitopes among the common allergens investigated, which for sensitized subjects may add to the risk of developing latex allergy.

  18. Formation of Defect-Free Latex Films on Porous Fiber Supports

    KAUST Repository

    Lively, Ryan P.; Mysona, Joshua A.; Chance, Ronald R.; Koros, William J.

    2011-01-01

    a defect-free lumen-side barrier layer can be created. Film experiments examined the effect of drying rate, latex age, substrate porosity (porous vs nonporous), and substrate hydrophobicity/ hydrophilicity. Film studies show that in ideal conditions

  19. The construction and commissioning of MINT's latex irradiator

    International Nuclear Information System (INIS)

    Razali Hamzah; Muhd Khairi Muhd Said; Muhd Ariff Hamzah; Wan Manshol Wan Zin; Taiman Kadni

    1996-01-01

    The construction and installation of MINT's automatic continuous latex irradiator is described. MINT cooperated with NUKEM to design the plant. Construction was done by local building consultants and local contractor. The installation of the plant includes local fabrication components and imported components. The plant is automatically controlled by a computer system. Features of plant is described

  20. Study of glucoamylase immobilization in butadiene nitrile latex membrane

    International Nuclear Information System (INIS)

    Miller, E.

    1992-01-01

    Attempts have been undetaken to immobilize glucoamylaze by means of butadiene nitrile latex in the presence of a chemical initiator and 60 Co γ-radiation. The activity, stability of conjugates in the membrane and permeability of oxygen in these membranes were determined. (author) 14 refs.; 5 figs

  1. Prevalence and clinical impact of sensitization to latex and fruits in dentistry students at the University of Antioquia, and its relationship with allergy to fruits

    Directory of Open Access Journals (Sweden)

    Echenique Manrique, Alejandro

    2015-04-01

    Full Text Available Objective: To determine the prevalence and clinical impact of sensitization to latex and to five tropical fruits (banana, avocado, kiwi, pineapple and passion fruit in dentistry students. Methods: Analytical cross-sectional study of 128 dentistry students at University of Antioquia in Medellín, Colombia. Information was collected by means of a questionnaire and skin prick tests with latex and fruits were done. Results: All students reported having had contact with latex. Nine of them informed at least one episode of adverse reaction to contact with latex without proof of sensitization to it. Five reported at least one reaction with one of the fruits, but skin prick tests were negative. Four of the 14 students who reported gastrointestinal symptoms were sensitized to latex or to one of the tested fruits. Overall, latex sensitization rate was 3.1%. Conclusion: This percentage of sensitization to latex is lower than that in other studies; this may be due to the expression of immune mechanisms other than IgE mediation. We failed to demonstrate a higher sensitization rate to latex as students advanced in their career. The association between gastrointestinal symptoms and sensitization to both fruit and latex is to be emphasized.

  2. Cost evaluation of radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Makuuchi, K.

    2003-01-01

    Cost of radiation vulcanized NR latex was evaluated. The plant would be built in an existing dipping factory in an industrial area in a Southeast Asian country. One thousands dry tons of NR latex are vulcanized with a low energy electron accelerator. The electron accelerator is a self-shielding low energy type. The maximum accelerating voltage is 300 kV and the output power is 10 kW. The total construction cost of the plant is $400,000 including electron accelerator and other equipments. Costs of raw materials and utilities are $1.165 and $0.023 per one kg of product, respectively. The fixed costs of the plant consist of labor costs, labor overhead, maintenance, plant overhead, depreciation, and bank interest. It is $0.190/kg of product. The company overhead for operation including company management, R and D and insurance is $0.044/kg of product. Thus, the total production cost is estimated to be $1.422/kg of product. (author)

  3. Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

    Energy Technology Data Exchange (ETDEWEB)

    Karim, Ahmad Fikri Abdul, E-mail: a.fikri-89@yahoo.com; Ariff, Zulkifli Mohamad [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia); Ismail, Hanafi [Cluster for Polymer Composites (CPC), Science and Engineering Research Centre, Engineering Campus, Universiti Sains Malaysia,14300 Nibong Tebal, Pulau Pinang (Malaysia)

    2015-07-22

    This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

  4. Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

    International Nuclear Information System (INIS)

    Karim, Ahmad Fikri Abdul; Ariff, Zulkifli Mohamad; Ismail, Hanafi

    2015-01-01

    This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

  5. A LaTeX graphics routine for drawing Feynman diagrams

    International Nuclear Information System (INIS)

    Levine, M.J.S.

    1990-01-01

    FEYNMAN is a LaTeX macropackage which allows the user to construct a versatile range of Feynman diagrams within the text of a document. Diagrams of publication quality may be drawn with relative ease and rapidity. (orig.)

  6. Radiation-induced grafting polymerization of MMA onto polybutadiene rubber latex

    International Nuclear Information System (INIS)

    Peng Jing; Wang Maolin; Qiao Jinliang; Wei Genshuan

    2005-01-01

    The grafting of methyl methacrylate (MMA) onto polybutadiene rubber latex by the direct radiation method was carried out. The effects of monomer concentration, absorbed dose and dose rate of gamma rays on the grafting yield were investigated. The graft copolymers were characterized by transmission electron microscopy (TEM), FTIR spectroscopy, and differential scanning calorimetry. TEM photographs revealed that the core-shell structures of latex particles are formed at low MMA content, and with the increasing of MMA content, the semi-IPN-like structure with core-shell could be developed due to the high gel fraction of polybutadiene (PBD) seed particles. In addition, infrared analysis confirmed that MMA could be grafted onto PBD molecular chains effectively under appropriate irradiation conditions. The interfacial adhesion between PBD rubber (core) and PMMA (shell) phases could be enhanced with the increase of MMA concentration

  7. Oil-Acrylic hybrid latexes as binders for waterborne coatings

    NARCIS (Netherlands)

    Hamersveld, E.M.S.; Es, van J.J.G.S.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

    1999-01-01

    The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

  8. Oil-acrylic hybrid latexes as binders for waterborne coatings

    NARCIS (Netherlands)

    Hamersveld, van E.M.S.; Es, van J.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

    1999-01-01

    The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

  9. Latex allergy in an infant with acquired hydrocephalus | Ehiozw ...

    African Journals Online (AJOL)

    We report the case of a 3 month old male infant with acquired hydrocephalus undergoing ventriculo-peritoneal shunt insertion who developed wheals and suffered a respiratory arrest following contact with latex gloves. The need for anaesthetists to effectively diagnose and properly manage this rare clinical entity is ...

  10. Surfactant and counter-ion distribution in styrene-butyl acrylate-acrylic acid dry latex submonolayers

    Directory of Open Access Journals (Sweden)

    Keslarek Amauri José

    2004-01-01

    Full Text Available Styrene-butyl acrylate-acrylic acid latex submonolayers prepared using a non-reactive phosphate surfactant together with a reactive sulfonate surfactant were examined in a transmission microscope using electron energy loss spectroscopy imaging (ESI-TEM. Phosphorus is nearly absent from the particles core but it is detected in a thick shell and in unusual, strongly scattering structures with a low carbon content, and largely made out of inorganic phosphate. P is also dispersed outside the particles, while S is uniformly distributed within then. The Na and N elemental maps show that the respective monovalent ions (Na+ and NH4+ have different distributions, in the latex: Na signal within the particles is stronger than in the background, while N is accumulated at the particle borders. The distributions of surfactant and counter-ions are thus different from some current assumptions, but they support recent results on the distribution of ionic constituents in latex films, by scanning electric potential microscopy.

  11. Extraction and comparison of proteins from natural rubber latex by conventional and ionizing radiation methods

    International Nuclear Information System (INIS)

    Rogero, Sizue O.; Spencer, Patrick J.; Campos, Vania E.; Lusvarghi, Fabio M.; Higa, Olga Z.

    1997-01-01

    Several proteins in natural rubber latex (NRL) have been assigned to be significant allergens. It is known that proteins submitted to ionizing radiation suffer denaturation and immunochemical modification resulting in low antigenic reactivity. The aim of this study was to extract and compare water extractable proteins from NRL films vulcanized by conventional and by ionizing radiation methods. SDS-polyacrylamide gel electrophoresis (SDS--PAGE) and high pressure liquid chromatography (HPLC) showed a diffuse protein band of about 14 KDa, which we believe is rubber elongation factor (REF), in both eluates, but smaller in latex film vulcanized by ionizing radiation. REF has been suggested to be a major latex allergen. These data suggest that ionizing radiation vulcanization could be an useful method for the production of NRL goods with low antigenicity. (author). 8 refs., 2 figs., 1 tab

  12. The polymerization of aniline in polystyrene latex particles

    Czech Academy of Sciences Publication Activity Database

    Blinova, Natalia V.; Reynaud, S.; Roby, F.; Trchová, Miroslava; Stejskal, Jaroslav

    2010-01-01

    Roč. 160, 15/16 (2010), s. 1598-1602 ISSN 0379-6779 R&D Projects: GA AV ČR IAA400500905; GA ČR GA203/08/0686; GA ČR GA202/09/1626 Institutional research plan: CEZ:AV0Z40500505 Keywords : polyaniline * polystyrene latex * polyaniline-polystyrene composite Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.871, year: 2010

  13. Acetylcholinesterase Inhibitory and Antioxidant Properties of Euphorbiacharacias Latex

    Directory of Open Access Journals (Sweden)

    Francesca Pintus

    2013-03-01

    Full Text Available The aim of the present study was to evaluate the acetylcholinesterase inhibitory capacity and the antioxidant properties of extracts of Euphorbia characias latex, a Mediterranean shrub. We performed a new extraction method involving the use of the trichloroacetic acid. The extract showed high antioxidant activity, was rich in total polyphenolic and flavonoid content and exhibited substantial inhibition of acetylcholinesterase activity.

  14. Study on durability of natural fibre concrete composites using ...

    Indian Academy of Sciences (India)

    33, No. 6, December 2010, pp. 719–729. * Indian Academy of Sciences. 719 ... vegetable fibre–cement composites. ... modified vegetable fibre–mortar composites was analysed ... exhibit better performance than conventional concrete.

  15. Type I allergy to natural rubber latex and type IV allergy to rubber chemicals in health care workers with glove-related skin symptoms.

    Science.gov (United States)

    Nettis, E; Assennato, G; Ferrannini, A; Tursi, A

    2002-03-01

    It has been established that there are type I and type IV allergens in latex gloves. The purpose of the study was to establish the prevalence of rubber glove-induced skin symptoms among health care workers in one Italian hospital. Health care workers (n = 1584) were evaluated using a written questionnaire and 295 respondents with glove-induced skin symptoms were tested. We performed: skin prick test with latex glove extract and commercial latex, and environmental and food allergens; glove use test; patch tests with a rubber additive series; and RASTs. Hospital employees who used or had used latex gloves at work were 1294. Three hundred and sixteen (24.4%) reported glove-induced symptoms, namely, cutaneous symptoms in all the cases and non-cutaneous symptoms in 105 subjects (8.1%). Twenty-seven of the 295 symptomatic employees tested (9.1%) were latex sensitive. Thirty-one patients (10.5%) exhibited positive patch test to rubber-related allergens. The most positive readings were obtained from the Thiuram mix and the Carba mix, with 12 and 9 positivities, respectively. The risk factors for latex skin sensitization were: a previous history of atopy and asthma; history of surgery; pre-existing hand dermatitis; work-related symptoms; and positive skin tests to common inhalant and certain foods (P skin complaints of latex gloves are related to skin irritation rather than to allergy. The immediate allergy to latex and the delayed allergy to rubber chemicals suggest that all the health care workers with glove-related dermatitis should undergo both skin prick test and glove use test to detect type I hypersensitivity to latex, and patch test to detect type IV hypersensitivity to rubber chemicals.

  16. Assessment of leaching from Construction & Demolition Waste concrete

    DEFF Research Database (Denmark)

    Butera, Stefania; Christensen, Thomas Højlund; Astrup, Thomas

    2012-01-01

    Construction and demolition waste features two very important properties when considering its management options: the large amounts, and the low environmental hazardousness. Therefore, concrete waste can be recycled relatively easily: most common end-of-life option is utilization as unbound...... approaches exist, often implying unrealistic or not relevant conditions if compared to real life utilization scenarios. A modified version of the CEN/TS 14405 column percolation test has been implemented on four crushed concrete samples, with the purpose of analysing the release of chromium, one...

  17. Impact Resistance of Recycled Aggregate Concrete with Single and Hybrid Fibers

    Directory of Open Access Journals (Sweden)

    Ismail Sallehan

    2016-01-01

    Full Text Available This paper presents a recycled aggregate concrete (RAC mix that has been modified by adding treated recycled concrete aggregate (RCA and various types of fiber-reinforced systems. The effectiveness of these modifications in terms of energy absorption and impact resistance was evaluated and compared with that of the corresponding regular concrete, as well as with unmodified RAC specimens. Results clearly indicate that although modification of the RAC mix with treated RCA significantly enhances the impact resistance of RAC, further diversification with additional fiber, particularly those in hybrid form, can optimize the results.

  18. Improving the Bond Strength of Rice Husk Ash Concrete by Incorporating Polymer: A New Approach

    OpenAIRE

    Bangwar, Daddan Khan; Ali Soomro, Mohsin; Ali Laghari, Nasir; Ali Soomro, Mukhtiar; Ali Buriro, Ahsan

    2018-01-01

    This paper gives an insight of how to improve the bond strength of cement in which concrete is replaced with rice husk ash. A concrete mix was prepared and was used in different types of mixes i.e. Control Mix, 10% cement substituted concrete with rice husk ash and polymer modified concrete by incorporation different dosages of polymer in the 10% cement substituted concrete. A bar of 12mm diameter, 300mm in length was placed in the center of the cylindrical specimens for pull out test. It was...

  19. Photocatalytic activity of titanium dioxide modified concrete materials - influence of utilizing recycled glass cullets as aggregates.

    Science.gov (United States)

    Chen, Jun; Poon, Chi-Sun

    2009-08-01

    Combining the use of photocatalysts with cementitious materials is an important development in the field of photocatalytic air pollution mitigation. This paper presents the results of a systematic study on assessing the effectiveness of pollutant degradation by concrete surface layers that incorporate a photocatalytic material - Titanium Dioxide. The photocatalytic activity of the concrete samples was determined by photocatalytic oxidation of nitric oxide (NO) in the laboratory. Recycled glass cullets, derived from crushed waste beverage bottles, were used to replace sand in preparing the concrete surface layers. Factors, which may affect the pollutant removal performance of the concrete layers including glass color, aggregate size and curing age, were investigated. The results show a significant enhancement of the photocatalytic activity due to the use of glass cullets as aggregates in the concrete layers. The samples fabricated with clear glass cullets exhibited threefold NO removal efficiency compared to the samples fabricated with river sand. The light transmittance property of glass was postulated to account for the efficiency improvement, which was confirmed by a separate simulation study. But the influence of the size of glass cullets was not evident. In addition, the photocatalytic activity of concrete surface layers decreased with curing age, showing a loss of 20% photocatalytic activity after 56-day curing.

  20. Antimicrobial activity of a 48-kDa protease (AMP48) from Artocarpus heterophyllus latex.

    Science.gov (United States)

    Siritapetawee, J; Thammasirirak, S; Samosornsuk, W

    2012-01-01

    Artocarpus heterophyllus (jackfruit) is a latex producing plant. Plant latex is produced from secretory cells and contains many intergradients. It also has been used in folk medicine. This study aimed to purify and characterize the biological activities of a protease from jackfruit latex. A protease was isolated and purified from crude latex of a jackfruit tree by acid precipitation and ion exchange chromatography. The proteolytic activities of protein were tested using gelatin- and casein-zymography. The molecular weight and isoelectric point (pl) of protein were analysed by SDS/12.5% PAGE and 2D-PAGE, respectively. Antimicrobial activity of protein was analysed by broth microdilution method. In addition, the antibacterial activity of protein against Pseudomonas aeruginosa ATCC 27853 was observed and measured using atomic force microscopy (AFM) technique. The purified protein contained protease activity by digesting gelatin- and casein-substrates. The protease was designated as antimicrobial protease-48 kDa or AMP48 due to its molecular mass on SDS-PAGE was approximately 48 kDa. The isoelectric point (pl) of AMP48 was approximately 4.2. In addition, AMP48 contained antimicrobial activities by it could inhibit the growths of Pseudomonas aeruginosa ATCC 27853 and clinical isolated Candida albicans at minimum inhibitory concentration (MIC) 2.2 mg/ml and Minimum microbicidal concentration (MMC) 8.8 mg/ml. AFM image also supported the antimicrobial activities of AMP48 by the treated bacterial morphology and size were altered from normal.

  1. Trialed production of low protein irradiated natural rubber latex in factory scale by gamma irradiation technique

    International Nuclear Information System (INIS)

    Utama, Marga; Herwinarni, S.; Halik, H.M.; Siswanto; Suharyanto; Syamsu, Y.; Handoko, B.

    2006-01-01

    Four tons fresh field natural rubber latex (FNRL) with total solid content 30% were added with 2 phr (part hundred ratio of rubber) normal butyl acrylate (nBA) then irradiated by gamma rays at 25 kGy. The irradiated FNRL was centrifuged, then the properties of irradiated centrifuged natural rubber latex (INRL) and its film were measured before and after storage for 5 months. It is found that the INRL is stable latex during storage in 5 months, with lowest protein, and free nitrosamine content. The tensile strength of INRL film was 24-27 MPa, and modulus 600% was 1,5-2,0 MPa, elongation at break was 900%, and hardness was 27-29 Shore A, while the extractable protein content less than 100 μg/g. (author)

  2. Morphologic evaluation of the use of a latex prosthesis in videolaparoscopic inguinoplasty: an experimental study in dogs Avaliação morfológica da utilização de prótese de latex na inguinoplastia videolaparoscópica: estudo experimental em cães

    Directory of Open Access Journals (Sweden)

    Luiz Henrique de Sousa

    2011-01-01

    Full Text Available PURPOSE: To evaluate the morphological aspects of the behavior of 4 types of latex biomembranes implanted in preperitoneal videolaparoscopic inguinoplasty. METHODS: Sixteen inguinoplasties were performed in 12 dogs: group 1 received an impermeable latex biomembrane in the right inguinal region and a prolene prosthesis, as control, in the contralateral inguinal region; groups 2, 3 and 4 received latex biomembranes respectively containing impermeable polyamide, 1-mm thick porous polyamide and 0.5-mm thick porous polyamide. Macro- and microscopic evaluations of the inguinal region and of the removed implants were made on the 7th, 14th, 21st and 28th days in group 1 and on the 28th postoperative day in the other groups. RESULTS: We observed absence of hematoma, seroma and infection; presence of tortuosities; induction of vascular neoformation, inflammatory reaction and collagen deposition, and full encystment of the latex biomembranes, except that with fine porous polyamide, which was partially incorporated, with the formation of microcysts. No latex biomembrane induced fibrosis as observed in the prolene control group. CONCLUSIONS: The biomembranes maintain induction of the healing process without fibrosis, are fully encysted and, except for the one with fine porous polyamide, are not incorporated into adjacent tissues. The latex biomembrane, with or without polyamide, is not recommended as a separate material for preperitoneal inguinoplasty.OBJETIVO: Avaliar aspectos morfológicos do comportamento de 4 tipos de biomembranas de latex, colocadas pré-peritonealmente em cães, por inguinoplastia videolaparoscópica. MÉTODOS: Dezesseis inguinoplastias em 12 cães: grupo 1, com biomembrana de latex impermeável inguinal direita em quatro cães e prótese de prolene, como controle, contra-lateral; grupos 2, 3 e 4, com biomembrana de latex respectivamente de poliamida impermeável, poliamida porosa com 1mm de espessura e poliamida porosa com 0,5mm de

  3. Whole-transcriptome survey of the putative ATP-binding cassette (ABC) transporter family genes in the latex-producing laticifers of Hevea brasiliensis.

    Science.gov (United States)

    Zhiyi, Nie; Guijuan, Kang; Yu, Li; Longjun, Dai; Rizhong, Zeng

    2015-01-01

    The ATP-binding cassette (ABC) proteins or transporters constitute a large protein family in plants and are involved in many different cellular functions and processes, including solute transportation, channel regulation and molecular switches, etc. Through transcriptome sequencing, a transcriptome-wide survey and expression analysis of the ABC protein genes were carried out using the laticiferous latex from Hevea brasiliensis (rubber tree). A total of 46 putative ABC family proteins were identified in the H. brasiliensis latex. These consisted of 12 'full-size', 21 'half-size' and 13 other putative ABC proteins, and all of them showed strong conservation with their Arabidopsis thaliana counterparts. This study indicated that all eight plant ABC protein paralog subfamilies were identified in the H. brasiliensis latex, of which ABCB, ABCG and ABCI were the most abundant. Real-time quantitative reverse transcription-polymerase chain reaction assays demonstrated that gene expression of several latex ABC proteins was regulated by ethylene, jasmonic acid or bark tapping (a wound stress) stimulation, and that HbABCB15, HbABCB19, HbABCD1 and HbABCG21 responded most significantly of all to the abiotic stresses. The identification and expression analysis of the latex ABC family proteins could facilitate further investigation into their physiological involvement in latex metabolism and rubber biosynthesis by H. brasiliensis.

  4. Leakage of pressurized gases through unlined concrete containment structures

    International Nuclear Information System (INIS)

    Rizkalla, S.H.; Simmonds, S.H.

    1983-01-01

    Eight reinforced concrete specimens were fabricated and subjected to tensile membrane forces and air pressure to study the air leakage characteristics in cracked reinforced concrete members. A mathematical expression for the rate of pressurized air flowing through an idealized crack is presented. The mathematical expression is refined by using the experimental data to describe the air flow rate through any given crack pattern. Graphical charts are also presented for the calculation of the air leakage rate through concrete cracks. The concept of equivalent crack width for a given crack pattern is introduced. The mathematical expression and graphical charts are modified to include this equivalent crack width concept. The proposed technique is applicable for the prediction of the leakage from concrete containment structures or any similar structures due to high internal pressure sufficient to initiate cracking. (orig.)

  5. Study on performance of waterborne anticorrosive coatings on steel rebars

    Science.gov (United States)

    Ramaswamy, S. N.; Varalakshmi, R.; Selvaraj, R.

    2017-12-01

    Durability of reinforced cement concrete structures is mainly affected by corrosion of steel reinforcements. In order to protect the reinforcing bars from corrosion and to enhance the lifetime of reinforced cement concrete structural members, anticorrosive treatment to steel is of prime importance. Conventional coatings are solvent based. In this study, water based Latex was used to formulate anticorrosive coating. Latex is applied to steel specimen substrates such as plates and rods and their mechanical properties such as flexibility, abrasion, bendability, adhesive strength, impact resistance, etc. were studied. It was inferred that coating containing latex, micro silica, zinc phosphate, ferric oxide, aluminum oxide, titanium oxide and silica fume was found to possess more corrosion resistance under marine exposure conditions.

  6. Polybutadiene latex particle size distribution analysis utilizing a disk centrifuge

    NARCIS (Netherlands)

    Verdurmen, E.M.F.J.; Albers, J.G.; German, A.L.

    1994-01-01

    Polybutadiene (I) latexes prepd. by emulsifier-free emulsion polymn. and having particle diam. 50-300 nm for both unimodal and bimodal particles size distributions were analyzed by the line-start (LIST) method in a Brookhaven disk centrifuge photosedimentometer. A special spin fluid was designed to

  7. Insights on the Phytochemical Profile (Cyclopeptides and Biological Activities of Calotropis procera Latex Organic Fractions

    Directory of Open Access Journals (Sweden)

    Thiago Lustosa Jucá

    2013-01-01

    Full Text Available Calotropis procera is a medicinal plant whose pharmacological properties are associated with its latex. Here, the Calotropis procera latex fractions were investigated in an attempt to trace its phytochemical profile and measure its anti-inflammatory and toxicity activity. The crude latex was partitioned, yielding five fractions (49.4% hexane, 5.2% dichloromethane, 2.0% ethyl acetate, 2.1% n-butanol, and 41.1% aqueous. Phytochemical screening and spectroscopy analysis revealed that dichloromethane is the most chemically diverse fraction. Triterpenes were detected in both the hexane and dichloromethane fractions, while flavonoids were detected in the dichloromethane and ethyl acetate fractions. These fractions were cytotoxic to cancer cell lines (LD50 0.05 to 3.9 μg/mL and lethal to brine shrimp (LD50 10.9 to 65.7 μg/mL. Reduced neutrophil migration in rats was observed in carrageenan-induced peritonitis for the dichloromethane (67%, ethyl acetate (56%, and aqueous (72% fractions. A positive reaction with tolidine and ninhydrin suggested that cyclopeptides are in the ethyl acetate fraction. It is therefore concluded that Calotropis procera latex dichloromethane and ethyl acetate fractions exhibit both in vitro and in vivo activities as well as anti-inflammatory properties. Cyclopeptide detection is especially interesting because previous attempts to investigate these low-molecular cyclic amino acid sequences in C. procera have failed.

  8. Assay of anti-HBs antibodies using a recombinant antigen and latex particle counting: comparison with five commercial tests.

    Science.gov (United States)

    Galanti, L M; Cornu, C; Masson, P L; Robert, A R; Becheanu, D; Lamy, M E; Cambiaso, C L

    1991-05-01

    An assay of anti-HBs antibodies based on agglutination of latex particles coated with recombinant HBs-antigen was compared with Abbott radioimmunoassay (Abbott-RIA), which uses a human plasma-derived antigen. The population examined consisted of 76 Abbott-RIA anti-HBs-negative prevaccinated subjects and 1044 serum samples anti-HBs found positive by Abbott-RIA, including 283 samples of subjects vaccinated either with a human plasma-derived vaccine (group A; n = 180) or with a recombinant vaccine (group B; n = 103). Correlation coefficients between the two techniques were respectively r = 0.89 for the whole population (n = 1044), r = 0.98 in group A and r = 0.74 in group B. Anti-HBs titres were higher with latex than with RIA in group B as shown by the regression slopes: latex = 508 + 1.11 RIA in group A and latex = -1138 + 3.97 RIA in group B, suggesting that some vaccinated subjects from group B produced antibodies against epitopes proper to the recombinant antigen. In the prevaccinated population and in group A, the latex results were compared with those of radioimmunoassays (Abbott, Sorin) and enzyme immunoassays (Behring, Roche, Pasteur). Only the Roche-EIA detected anti-HBs in the prevaccinated subjects. The correlation between the various immunoassays was r greater than 0.96 only for values higher than 100 IU/l.

  9. Clonal stability of latex yield in eleven clones of Hevea brasiliensis Muell. Arg.

    Directory of Open Access Journals (Sweden)

    K.O. Omokhafe

    2003-01-01

    Full Text Available Eleven Hevea brasiliensis clones were evaluated for clonal stability of latex yield. A randomized complete block design was used with four replicates, two locations, seven years and three periods per year. Stability analysis was based on clone x year and clone x year x location interactions. Five stability parameters viz environmental variance, shukla's stability variance, regression of clonal latex yield on environmental index, variance due to regression and variance due to deviation from regression were applied. There was significant clone x environment effect at the two levels of interaction. Among the eleven clones, C 162 was outstanding for clonal stability and it can serve as donor parent for stability alleles. Three clones (C 76, C 150 and C 154 were also stable. The four stable clones (C 76, C 150, C 154 and C 162 are suitable for broad-spectrum recommendation for latex yield. Five clones (C 83, C 143, C 163, C 202 and RRIM 600 will require environment-specific recommendation because of their unstable phenotype. The stability feature of two clones (C 145 and C 159 was not clear and this will be investigated in subsequent studies.

  10. Recycled Concrete as Aggregate for Structural Concrete Production

    Directory of Open Access Journals (Sweden)

    Mirjana Malešev

    2010-04-01

    Full Text Available A comparative analysis of the experimental results of the properties of fresh and hardened concrete with different replacement ratios of natural with recycled coarse aggregate is presented in the paper. Recycled aggregate was made by crushing the waste concrete of laboratory test cubes and precast concrete columns. Three types of concrete mixtures were tested: concrete made entirely with natural aggregate (NAC as a control concrete and two types of concrete made with natural fine and recycled coarse aggregate (50% and 100% replacement of coarse recycled aggregate. Ninety-nine specimens were made for the testing of the basic properties of hardened concrete. Load testing of reinforced concrete beams made of the investigated concrete types is also presented in the paper. Regardless of the replacement ratio, recycled aggregate concrete (RAC had a satisfactory performance, which did not differ significantly from the performance of control concrete in this experimental research. However, for this to be fulfilled, it is necessary to use quality recycled concrete coarse aggregate and to follow the specific rules for design and production of this new concrete type.

  11. How Concrete Is Concrete?

    Science.gov (United States)

    Gravemeijer, Koeno

    2011-01-01

    If we want to make something concrete in mathematics education, we are inclined introduce, what we call, "manipulatives", in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own,…

  12. Trial Production of Surgical Gloves from Irradiated Natural Rubber Latex on Factory Scale

    Directory of Open Access Journals (Sweden)

    M. Utama

    2005-07-01

    Full Text Available Trial production of surgical gloves from irradiated natural rubber latex at the PT. Laxindo Utama Serang Banten glove factory has been carried out. The variation of heating temperature and leaching time during processing were evaluated. The physical and mechanical properties and the protein allergen respond of surgical gloves using ELISA method were measured. The results showed that the physical and mechanical of surgical gloves such as tensile strength, modulus, and elongation at break arefound to meet the requirements of the ISO or SNI standard for surgical gloves. While the allergic response through clinical tested latex-sensitive protein allergen known as ELISA test is found to be negative.

  13. Latex allergy: assessment of knowledge, appropriate use of gloves and prevention practice among hospital healthcare workers.

    Science.gov (United States)

    Al-Niaimi, F; Chiang, Y Z; Chiang, Y N; Williams, J

    2013-01-01

    Healthcare workers and patients are often exposed to natural rubber latex (NRL) through contact with gloves and various healthcare products, which can potentially cause allergic reactions, with varying degrees of severity. In 2008, the Royal College of Physicians published their first evidence-based guidance on occupational health interventions for latex allergy, which emphasized the importance of healthcare workers having knowledge of latex allergy. This study aimed to survey the knowledge of healthcare workers (n = 156) about latex gloves and NRL allergy, routine prevention practice and the appropriate use of gloves in patient care. Healthcare workers in a large teaching hospital were surveyed using a standard questionnaire. We found that only 1% of healthcare workers were able to correctly match the appropriate gloves to the specifically designed procedure. More than half (n = 74.53%) were unable to recognize the presentation of type 1 allergy to NRL. Of the 156 participants, 131 (84%) considered that they would benefit from training about NRL allergy and the use of different types of gloves in clinical care. This survey indicates the importance of education regarding appropriate use of gloves and prevention of NRL allergy among healthcare workers, and dermatologists should play an important role in facilitating this. © The Author(s). CED © 2012 British Association of Dermatologists.

  14. Usage of Crushed Concrete Fines in Decorative Concrete

    Science.gov (United States)

    Pilipenko, Anton; Bazhenova, Sofia

    2017-10-01

    The article is devoted to the questions of usage of crushed concrete fines from concrete scrap for the production of high-quality decorative composite materials based on mixed binder. The main problem in the application of crushed concrete in the manufacture of decorative concrete products is extremely low decorative properties of crushed concrete fines itself, as well as concrete products based on them. However, crushed concrete fines could have a positive impact on the structure of the concrete matrix and could improve the environmental and economic characteristics of the concrete products. Dust fraction of crushed concrete fines contains non-hydrated cement grains, which can be opened in screening process due to the low strength of the contact zone between the hydrated and non-hydrated cement. In addition, the screening process could increase activity of the crushed concrete fines, so it can be used as a fine aggregate and filler for concrete mixes. Previous studies have shown that the effect of the usage of the crushed concrete fines is small and does not allow to obtain concrete products with high strength. However, it is possible to improve the efficiency of the crushed concrete fines as a filler due to the complex of measures prior to mixing. Such measures may include a preliminary mechanochemical activation of the binder (cement binder, iron oxide pigment, silica fume and crushed concrete fines), as well as the usage of polycarboxylate superplasticizers. The development of specific surface area of activated crushed concrete fines ensures strong adhesion between grains of binder and filler during the formation of cement stone matrix. The particle size distribution of the crushed concrete fines could achieve the densest structure of cement stone matrix and improve its resistance to environmental effects. The authors examined the mechanisms of structure of concrete products with crushed concrete fines as a filler. The results of studies of the properties of

  15. Quality control of concrete structures in nuclear power plant, (3)

    International Nuclear Information System (INIS)

    Takahashi, Hisao; Kawaguchi, Tohru; Oike, Takeshi; Morimoto, Shoichi; Takeshita, Shigetoshi.

    1979-01-01

    In general, concrete placed in the winter season has a tendency to have lower strength at the age of 4 weeks due to low curing temperature after placement. Therefore, under the Japanese code, the target mix Proportions in the winter season are modified adding an extra correction factor based on air temperature. Meanwhile, the quality control system for mass concrete to be placed in the winter system is indistinct at this stage. It is the aim of this report to present the results of investigations to clarify the following two subjects: (1) whether the correction factor due to temperature is needed or not for mass concrete in the winter season; (2) what kind of curing should be applied to control cylinders for estimating strength of mass concrete. (author)

  16. Flexural strength of structural concrete repaired with HBPMM cement

    International Nuclear Information System (INIS)

    Memon, G.H.; Khaskheli, G.B.; Kumar, A.

    2009-01-01

    To repair damaged concrete structures, Dadabhoy Cement Factory in Sindh has launched a product known as HBPMM (Hi-Bond Polymer Modified Mortar) cement. HBPMM is used to repair various concrete structures in Pakistan but the experimental back up regarding the real performance of the product, as far as flexural strength of concrete is concerned, is not well known yet. This study is thus aimed to investigate the flexural strength of structural concrete repaired with HBPMM compared to that repaired with OPC (Ordinary Portland Cement). In total 32 concrete beams (6x6x18) having compressive strength of 3000 and 5000 psi were manufactured. To obtain flexural strength of the beams, these were splitted by using a UTM (Universal Testing Machine). Beams were then repaired with different applications of HBPMM and OPC. After 28 days of curing, the repaired beams were re-splitted to determine the flexural strength of repaired beams. Results show that both HBPMM and OPC are not very effective. However, the performance of HBPMM remained slightly better than that of OPC. Both OPC and HBPMM remained more efficient in case of 5000 psi concrete than that of 3000 psi concrete. Flexural strength of repaired beams could be increased by increasing application of the repairing material. (author)

  17. Diagnosis of Trichomonous vaginalis by microscopy, latex agglutination, diamond's media, and PCR in symptomatic women, Khartoum, Sudan.

    Science.gov (United States)

    Saleh, Amir M; Abdalla, Hamid S; Satti, Abdelsalam B; Babiker, Suad M; Gasim, Gasim I; Adam, Ishag

    2014-03-06

    Trichomoniasis is the most common sexually transmitted disease. However, limited data are available on an effective technique for the diagnosis of Trichomonas vaginalis. A cross-sectional study was conducted to evaluate the accuracy of wet mount microscopy, latex agglutination, Diamond's media, and polymerase chain reaction (PCR) for detection of T. vaginalis among symptomatic women who attended the gynecological clinic at Khartoum, Sudan. Of the 297 women studied, 252 (84.8%) were positive for T. vaginalis by wet mount microscopy, 257 (86.5%) by latex agglutination, 253 (85.2%) by Diamond's media, and 253 (85.2%) by PCR. The sensitivity and specificity of wet mount microscopy were 99.2% and 97.7%, respectively, compared with PCR. The sensitivity and specificity of latex agglutination and Diamond's media were 99.6% and 88.6%, and 100.0% and 86.4%, respectively, compared with PCR. In this study, wet mount microscopy, latex agglutination, and Diamond's media were found to be highly sensitive and specific. However, the availability and cost effectiveness might limit the use of Diamond's media and PCR in routine practice. The virtual slide(s) for this article can be found here: http://www.diagnosticpathology.diagnomx.eu/vs/7859723851211496.

  18. Preparation and Characterization of Conducting Polymer Latices by Chemical Polymerization of Aniline or Anisidine in Presence of Latex: Study of Their Electroactivity and Anti-Corrosion Properties

    Directory of Open Access Journals (Sweden)

    Bakhshali Massoumi

    2013-06-01

    Full Text Available Poly (vinylacetate-co-butylmethacrylate was prepared in presence of potassium persulphate as an oxidizing agent in aqueous solution of dodecylbenzene sulfonate sodium as an emulsifying agent. Then, aniline was polymerized by chemical oxidation method at three different concentrations of aniline monomer (0.1, 0.2 and 0.3 M in toluene in presence of poly(vinylacetate-co-butylmethacrylate in order to obtain polyaniline/poly(vinylacetate-co-butylmethacrylate. To prepare conducting-latex of polyanisidine/poly(vinylacetate-co-butylmethacrylate the same method was employed as above for aniline monomer in obtaining conducting polyaniline/poly(vinylacetate-co-butylmethacrylate latex. In addition, the purification of conducting-latex polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate was conducted and preparation of tin layer films of conducting-latex polymers was carried out by casting method on glassy lames. The electroactivity properties of the prepared latex-polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate were investigated by cyclic voltammetery (CV. The voltamogrames showed that the latex films were electroactive. Because of conductivity and electroactivity, the obtained films may find applications in anti-corrosion coatings. The anti-corrosion properties of conducting-latex polymers were studied on aluminum surface by impedance technique. The structure of the prepared conducting-latex polymers was confirmed by Fourier transform infrared (FTIR. Finally, the electrical conductivity of synthesized conducting-latex polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate was measured by four probe technique.

  19. Comparison of Mechanical Properties of Lightweight and Normal Weight Concretes Reinforced with Steel Fibers

    Directory of Open Access Journals (Sweden)

    A. Ali

    2018-04-01

    Full Text Available Compared to conventional concrete, lightweight concrete is more brittle in nature however, in many situations its application is advantageous due to its lower weight. The associated brittleness issue can be, to some extent, addressed by incorporation of discrete fibers. It is now established that fibers modify some fresh and hardened concrete properties. However, evaluation of those properties for lightweight fiber-reinforced concrete (LWFC against conventional/normal weight concrete of similar strength class has not been done before. Current study not only discusses the change in these properties for lightweight concrete after the addition of steel fibers, but also presents a comparison of these properties with conventional concrete with and without fibers. Both the lightweight and conventional concrete were reinforced with similar types and quantity of fibers. Hooked end steel fibers were added in the quantities of 0, 20, 40 and 60kg/m3. For similar compressive strength class, results indicate that compared to normal weight fiber-reinforced concrete (NWFC, lightweight fiber-reinforced concrete (LWFC has better fresh concrete properties, but performs poorly when tested for hardened concrete properties.

  20. Effects of syntactic structure in the memory of concrete and abstract Chinese sentences.

    Science.gov (United States)

    Ho, C S; Chen, H C

    1993-09-01

    Smith (1981) found that concrete English sentences were better recognized than abstract sentences and that this concreteness effect was potent only when the concrete sentence was also affirmative but the effect switched to an opposite end when the concrete sentence was negative. These results were partially replicated in Experiment 1 by using materials from a very different language (i.e., Chinese): concrete-affirmative sentences were better remembered than concrete-negative and abstract sentences, but no reliable difference was found between the latter two types. In Experiment 2, the task was modified by using a visual presentation instead of an oral one as in Experiment 1. Both concrete-affirmative and concrete-negative sentences were better memorized then abstract ones in Experiment 2. The findings in the two experiments are explained by a combination of the dual-coding model and Marschark's (1985) item-specific and relational processing. The differential effects of experience with different language systems on processing verbal materials in memory are also discussed.

  1. Flow simulation of fiber reinforced self compacting concrete using Lattice Boltzmann method

    DEFF Research Database (Denmark)

    Svec, Oldrich; Skocek, Jan; Stang, Henrik

    2011-01-01

    Self compacting concrete (SCC) is a promising material in the civil engineering industry. One of the benefits of the SCC is a fast and simplified casting followed by decreased labor costs. The SCC as any other type of concrete has a significantly lower tensile and shear strength in comparison to ....... A relatively new group of models - Lattice Boltzmann Modeling (LBM) - is presented in this paper. The conventional LBM is modified to include fiber and particle suspensions and non-Newtonian rheology and is used to model the fiber reinforced self compacting concrete flow....

  2. Optimizing of the recycling of contaminated concrete debris. Final report

    International Nuclear Information System (INIS)

    Kloeckner, J.; Rasch, H.; Schloesser, K.H.; Schon, T.

    1999-01-01

    1. Latest research: So far concrete debris from nuclear facilities has been free released or was treated as radioactive waste. 2. Objective: The objective of this study is to develop solutions and methods for recycling concrete debris. The amount of materials used in nuclear facilities should be limited and the contamination of new materials should be avoided. 3. Methods: The status of recycling was presented using examples of operating or completed decommissioning as well as available studies and literature. The quality requirements for the production of new concrete products using recycled materials has been discussed. The expected amounts of concrete debris for the next 12 years was estimated. For the proposed recycling examples, radiological and economic aspects have been considered. 4. Results: The production of qualified concrete products from concrete debris is possible by using modified receptions. Technical regulations to this are missing. There is no need for the utilization of large amounts of concrete debris for shielding walls. For the production of new shielding-containers for radioactive waste, concrete debris can be applied. Regarding the distance to a central recycling facility the use of mobile equipment can be economical. By using the concrete for filling the cavity or space in a final storage, it is possible to dispose the whole radioactive debris. 5. Application possibilities: The use of concrete debris as an inner concrete shielding in waste-containers today is already possible. For the manufacture of qualified concrete products by using recycling products, further developments and regulations are necessary. (orig.) [de

  3. Radio-vulcanization of natural rubber in the latex phase. Study of an experimental 1 tonne per hour production; Radio-vulcanisation du caoutchouc naturel en phase latex. Etude d'une production experimentale de 1 tonne par heure

    Energy Technology Data Exchange (ETDEWEB)

    Leveque, P; Puig, J R; Roudeix, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    After briefly reviewing the main research carried out on the radio-vulcanization of latex and elastomers, a description is given of 4 types of cell which have been used successively with a view to industrial irradiation. They have made it possible to acquire the information necessary for resolving the main problem arising during irradiation - the formation of coagulum. The first two cell are designed for irradiation by a horizontal beam ('Dynamitron'), the two others use a vertical beam ('Circe'). The study of the properties of the rubber obtained shows it to compare favorably with 'Revultex'. In the appendix are given some characteristics of natural latex and information about its processing. (authors) [French] Apres un rappel des principales etudes sur la radio-vulcanisation du latex et des elastomeres, on decrit les quatre types de cellules successivement essayes en vue de l'irradiation industrielle. Ils ont permis d'acquerir les informations necessaires a la resolution du probleme principal pose par l'irradiation, la formation de coagulum au cours de celle,-ci. Les deux premiers sont concus pour l'irradiation par un faisceau horizontal ('Dynamitron'), les derniers par un faisceau vertical ('Circe'). L'etude des proprietes du caoutchouc obtenu montre qu'il se compare favorablement au 'Revultex'. Un apercu est donne en annexe des caracteristiques du latex naturel et de sa mise en oeuvre. (auteurs)

  4. A Latex Metabolite Benefits Plant Fitness under Root Herbivore Attack.

    Directory of Open Access Journals (Sweden)

    Meret Huber

    2016-01-01

    Full Text Available Plants produce large amounts of secondary metabolites in their shoots and roots and store them in specialized secretory structures. Although secondary metabolites and their secretory structures are commonly assumed to have a defensive function, evidence that they benefit plant fitness under herbivore attack is scarce, especially below ground. Here, we tested whether latex secondary metabolites produced by the common dandelion (Taraxacum officinale agg. decrease the performance of its major native insect root herbivore, the larvae of the common cockchafer (Melolontha melolontha, and benefit plant vegetative and reproductive fitness under M. melolontha attack. Across 17 T. officinale genotypes screened by gas and liquid chromatography, latex concentrations of the sesquiterpene lactone taraxinic acid β-D-glucopyranosyl ester (TA-G were negatively associated with M. melolontha larval growth. Adding purified TA-G to artificial diet at ecologically relevant concentrations reduced larval feeding. Silencing the germacrene A synthase ToGAS1, an enzyme that was identified to catalyze the first committed step of TA-G biosynthesis, resulted in a 90% reduction of TA-G levels and a pronounced increase in M. melolontha feeding. Transgenic, TA-G-deficient lines were preferred by M. melolontha and suffered three times more root biomass reduction than control lines. In a common garden experiment involving over 2,000 T. officinale individuals belonging to 17 different genotypes, high TA-G concentrations were associated with the maintenance of high vegetative and reproductive fitness under M. melolontha attack. Taken together, our study demonstrates that a latex secondary metabolite benefits plants under herbivore attack, a result that provides a mechanistic framework for root herbivore driven natural selection and evolution of plant defenses below ground.

  5. A Latex Metabolite Benefits Plant Fitness under Root Herbivore Attack.

    Science.gov (United States)

    Huber, Meret; Epping, Janina; Schulze Gronover, Christian; Fricke, Julia; Aziz, Zohra; Brillatz, Théo; Swyers, Michael; Köllner, Tobias G; Vogel, Heiko; Hammerbacher, Almuth; Triebwasser-Freese, Daniella; Robert, Christelle A M; Verhoeven, Koen; Preite, Veronica; Gershenzon, Jonathan; Erb, Matthias

    2016-01-01

    Plants produce large amounts of secondary metabolites in their shoots and roots and store them in specialized secretory structures. Although secondary metabolites and their secretory structures are commonly assumed to have a defensive function, evidence that they benefit plant fitness under herbivore attack is scarce, especially below ground. Here, we tested whether latex secondary metabolites produced by the common dandelion (Taraxacum officinale agg.) decrease the performance of its major native insect root herbivore, the larvae of the common cockchafer (Melolontha melolontha), and benefit plant vegetative and reproductive fitness under M. melolontha attack. Across 17 T. officinale genotypes screened by gas and liquid chromatography, latex concentrations of the sesquiterpene lactone taraxinic acid β-D-glucopyranosyl ester (TA-G) were negatively associated with M. melolontha larval growth. Adding purified TA-G to artificial diet at ecologically relevant concentrations reduced larval feeding. Silencing the germacrene A synthase ToGAS1, an enzyme that was identified to catalyze the first committed step of TA-G biosynthesis, resulted in a 90% reduction of TA-G levels and a pronounced increase in M. melolontha feeding. Transgenic, TA-G-deficient lines were preferred by M. melolontha and suffered three times more root biomass reduction than control lines. In a common garden experiment involving over 2,000 T. officinale individuals belonging to 17 different genotypes, high TA-G concentrations were associated with the maintenance of high vegetative and reproductive fitness under M. melolontha attack. Taken together, our study demonstrates that a latex secondary metabolite benefits plants under herbivore attack, a result that provides a mechanistic framework for root herbivore driven natural selection and evolution of plant defenses below ground.

  6. Synthesis and characterization of novel fluoroalkyl-terminated hyperbranched polyurethane latex

    Science.gov (United States)

    Xu, Wei; Zhao, Weijia; Hao, Lifen; Wang, Sha; Pei, Mengmeng; Wang, Xuechuan

    2018-04-01

    Waterborne polyurethane (PU) emulsions are widely used in various fields and the demand for them is ever-increasing over the years. However, the hydrophilic chain extender inevitably bonded into the PU backbone can affect the water tolerance of PU. Thus, it is of great importance to improve PU water resistance effectively. Herein, novel fluoroalkyl-terminated hyperbranched polyurethane (HBPUF) latex was accordingly synthesized by graft reaction of perfluorohexyl ethyl alcohol and hyperbranched polyurethane (HBPU), which was previously obtained from interaction between hydroxyl-terminated hyperbranched polymer and PU prepolymer manufactured via the acetone process, as well as using neutralization, adding water, and high-speed stirring operations. We characterized the resultants and investigated its surface properties by IR, NMR, TEM, XRD, TGA, DSC, FE-SEM, AFM, XPS, and contact angle measurements, etc. IR and NMR tests confirmed that the fluorinated fragments had been grafted onto the tail end of HBPU. TEM, XRD, DSC, and FE-SEM results all accounted for the fact that there were multi-crystals in PU, HBPU and HBPUF. TGA results showed that thermal stabilities of the PU, HBPU, and HBPUF latex films were enhanced in turn. XPS and AFM analyses demonstrated that the fluorine-containing segments from the HBPUF terminals were prone to migrate and enrich on the film-air surface of the HBPUF latex film, which made water contact angle and water absorption of the HBPUF film be as 113.9° and 11.1%, respectively, compared to those of the PU film (77.8° and 136.2%). This research indicates that water resistance of the PU film can be efficiently enhanced by fluorinated polyurethane with novel fluoroalkyl-terminated hyperbranched structure.

  7. Experimental Study and Shear Strength Prediction for Reactive Powder Concrete Beams

    Directory of Open Access Journals (Sweden)

    Maha M.S. Ridha

    2018-06-01

    Full Text Available Eighteen reactive powder concrete (RPC beams subjected to monotonic loading were tested to quantify the effect of a novel cementitious matrix materials on the shear behavior of longitudinally reinforced RPC beams without web reinforcement. The main test variables were the ratio of the shear span-to- effective depth (a/d, the ratio of the longitudinal reinforcement (ρw, the percentage of steel fibers volume fractions (Vf and the percentage of silica fume powder (SF. A massive experimental program was implemented with monitoring the concrete strain, the deflection and the cracking width and pattern for each RPC beam during the test at all the stages of the loading until failure. The findings of this paper showed that the addition of micro steel fibers (Lf/Df = 13/0.2 into the RPC mixture did not dramatically influence the initial diagonal cracking load whereas it improved the ultimate load capacity, ductility and absorbed energy. The shear design equations proposed by Ashour et al. and Bunni for high strength fiber reinforced concrete (HSFRC beams have been modified in this paper to predict the shear strength of slender RPC beams without web reinforcement and with a/d ≥ 2.5. The predictions of the modified equations are compared with Equations of Shine et al., Kwak et al. and Khuntia et al. Both of the modified equations in this paper gave satisfied predictions for the shear strength of the tested RPC beams with COV of 7.9% and 10%. Keywords: Beams, Ductility, Crack width, Absorbed energy, Reactive powder concrete, Steel fibers

  8. Recycled Concrete as Aggregate for Structural Concrete Production

    OpenAIRE

    Mirjana Malešev; Vlastimir Radonjanin; Snežana Marinković

    2010-01-01

    A comparative analysis of the experimental results of the properties of fresh and hardened concrete with different replacement ratios of natural with recycled coarse aggregate is presented in the paper. Recycled aggregate was made by crushing the waste concrete of laboratory test cubes and precast concrete columns. Three types of concrete mixtures were tested: concrete made entirely with natural aggregate (NAC) as a control concrete and two types of concrete made with natural fine and recycle...

  9. The Future Concrete: Self-Compacting Concrete

    OpenAIRE

    Iureş, Liana; Bob, Corneliu

    2010-01-01

    The paper presents the characteristics of the self-compacting concretes, their advantages and disadvantages when they are used in buildings. Due to its properties and composition, the self-compacting concrete is described here as being one of the future friendly enviromental material for buildings. Tests concerning to obtaining a self-compacting concrete, together with the specific fresh concrete properties tests, are described.

  10. Amine-modified magnetic iron oxide nanoparticle as a promising carrier for application in bio self-healing concrete.

    Science.gov (United States)

    Seifan, Mostafa; Ebrahiminezhad, Alireza; Ghasemi, Younes; Samani, Ali Khajeh; Berenjian, Aydin

    2018-01-01

    Self-healing mechanisms are a promising solution to address the concrete cracking issue. Among the investigated self-healing strategies, the biotechnological approach is distinguished itself by inducing the most compatible material with concrete composition. In this method, the potent bacteria and nutrients are incorporated into the concrete matrix. Once cracking occurs, the bacteria will be activated, and the induced CaCO 3 crystals will seal the concrete cracks. However, the effectiveness of a bio self-healing concrete strictly depends on the viability of bacteria. Therefore, it is required to protect the bacteria from the resulted shear forces caused by mixing and drying shrinkage of concrete. Due to the positive effects on mechanical properties and the high compatibility of metallic nanoparticles with concrete composition, for the first time, we propose 3-aminopropyltriethoxy silane-coated iron oxide nanoparticles (APTES-coated IONs) as a biocompatible carrier for Bacillus species. This study was aimed to investigate the effect of APTES-coated IONs on the bacterial viability and CaCO 3 yield for future application in the concrete structures. The APTES-coated IONs were successfully synthesized and characterized by transmission electron microscopy (TEM), X-ray powder diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The results show that the presence of 100 μg/mL APTES-coated IONs could increase the bacterial viability. It was also found that the CaCO 3 -specific yield was significantly affected in the presence of APTES-coated IONs. The highest CaCO 3 -specific yield was achieved when the cells were decorated with 50 μg/mL of APTES-coated IONs. This study provides new insights for the application of APTES-coated IONs in designing bio self-healing strategies.

  11. Modified Disk-Shaped Compact Tension Test for Measuring Concrete Fracture Properties

    Czech Academy of Sciences Publication Activity Database

    Cifuentes, H.; Lozano, M.; Holušová, Táňa; Medina, F.; Seitl, Stanislav; Fernández-Canteli, A.

    2017-01-01

    Roč. 11, č. 2 (2017), s. 215-228 ISSN 1976-0485 R&D Projects: GA ČR(CZ) GA16-18702S Institutional support: RVO:68081723 Keywords : Concrete * Fracture behaviour * Experimental techniques Subject RIV: JL - Materials Fatigue, Friction Mechanics OBOR OECD: Audio engineering, reliability analysis Impact factor: 2.031, year: 2016

  12. Experimental study on the effect of volcanic residue on the performance of recycled lightweight aggregate concrete

    Science.gov (United States)

    Xiao, Li-guang; Li, Ji-heng; Liu, Qing-shun

    2017-08-01

    Recycled lightweight aggregate concrete prepared with waste brick recycled light aggregate has high water absorption, large apparent density and poor frost resistance. The technical measures of regen-erating lightweight aggregate concrete with modified waste bricks from volcanic slag are put forward. The effects of volcanic slag on the properties of waste lightweight aggregate concrete were studied. The experi-mental results show that volcanic slag can significantly reduce the apparent density of recycled lightweight aggregate concrete and improve its frost resistance.

  13. Radiation Vulcanization of Natural Rubber Latex (RVNRL): A Potential Material for Nuclear Power Plant Gloves

    International Nuclear Information System (INIS)

    Pairu Ibrahim; Wan Manshol Wan Zain; Keong, C.C.; Mohd Noorwadi Mat Lazim

    2011-01-01

    Radiation vulcanization of natural rubber latex has great potential for the production of nuclear power plant gloves due to its low ash and mineral content. And this is in-line with the role played by Malaysian Nuclear Agency as Technical Supporting Organization for Nuclear Power Program. This paper discussed the evaluation done to determine ash content in RVNRL and SVNRL films. Both samples were prepared using casting technique and the properties were compared. Films prepared from raw latex without any vulcanizing agent were regarded as a control. (author)

  14. Study on grafting of monomer onto natural rubber latex by radiation technique

    International Nuclear Information System (INIS)

    Nguyen Tan Man; Le Hai; Tran Thi Tam; Le Huu Tu, Pham Thi Sam; Dao Minh Phuong; Ha Thuc Huy

    2004-01-01

    Radiation vulcanization of natural rubber latex has been extensively developed through programmers assisted by the IAEA and UNDP under RCA in Asia and Pacific Region. R-D has been done in most of the Member States with technical assistance from Japan's Takasaki Radiation Chemistry Establishment. Radiation vulcanized natural rubber latex (RVNRL) has many advantages over the conventional sulfur vulcanized latex, such as absence of nitrosamine and low cytotoxicity. Radiation crosslinking is a room temperature process, itself an important cost advantage, it is easily controlled and desired extend of crosslinking is easily achieved by controlling the dose (irradiation time). Disadvantages of RVNRL to be improved are poor physical properties of film such as low tensile strength and tear strength. The research groups of Japan, Thailand and Indonesia concentrated on the improvement of physical properties of RVNRL using radiation grafted PMMA as additive [2]. F. Sundardi and W. Sofiarti have reported that tensile strength and hardness increased by radiation grafting of styrene onto NR [5]. Ono et al have reported the grafting of MMA onto NR by gamma irradiation at a dose of 5 kGy for producing thermoplastic elastomers [4]. The objective of this project is to report the results of studies of radiation graft-copolymerization of methyl methacrylate (MMA) or styrene (St) onto natural rubber latex in order to improve their physico-mechanical properties and evaluation of grafted material using Small-Angle Neutron Scattering through FNCA Project. The grafting degree of MMA and St onto NR increased with the increase of irradiation dose and monomer concentration. The alteration of grafted products structure was determined by IR method. Tensile strength, Shore A hardness, 100% modulus of grafted products increased with the increase of monomer concentration and irradiation dose while elongation at break decreased. The grafted products were characterized by Transmission Electron

  15. Development of Tensile Softening Model for Plain Concrete

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.K.; Song, Y.C. [Korea Electric Power Research Institute, Taejon (Korea)

    2002-07-01

    Large-scale direct tensile softenng tests using plate concrete specimens(4000, 5000psi) with notch were performed under uniaxial stress. There were presented the basic physical properties and the complete load-CMOD(Crack Mouth Opening Displacement) curves for them And them the fracture energy was evaluated using the complete load-CMOD curves respectively, and there was presents optimal tensile softening model which is modified by a little revision of an existing one. Therefore, here provided the real verification data through the tests for developing other nonlinear concrete finite element models. (author). 32 refs., 38 figs., 4 tabs.

  16. The Future Concrete: Self-Compacting Concrete

    Directory of Open Access Journals (Sweden)

    Liana Iureş

    2010-01-01

    Full Text Available The paper presents the characteristics of the self-compacting concretes, their advantages and disadvantages when they are used in buildings. Due to its properties and composition, the self-compacting concrete is described here as being one of the future friendly enviromental material for buildings. Tests concerning to obtaining a self-compacting concrete, together with the specific fresh concrete properties tests, are described.

  17. Composite poly(methyl methacrylate-methacrylic acid-2-hydroxyethyl methacrylate) latex for immunoassay. The case of plasminogen.

    Science.gov (United States)

    Miksa, B; Wilczynska, M; Cierniewski, C; Basinska, T; Slomkowski, S

    1995-01-01

    Poly(methyl methacrylate-methacrylic acid-2-hydroxyethyl methacrylate) latex (ACRYLAT) was synthesized by radical precipitation polymerization. The mass median diameter (MMD) and the geometrical standard deviation (GSD) of the ACRYLAT particles were 138 nm and 1.2, respectively. The concentration of the titrable carboxylic groups in the surface layer of latex particles was equal to 8.41 x 10(-6) mol m-2. Latex was able to bind up to 2.82 x 10(-7) mol of 1-aminopyrene per 1 m2 of the surface of the latex particles due to the ionic interactions between carboxylate anions and ammonium cations of protonated 1-aminopyrene. ACRYLAT was able to immobilize covalently human serum albumin in amounts up to 0.23 mg m-2. Aggregation of ACRYLAT with immobilized HSA, induced with specific antibodies (anti-HSA), was investigated turbidimetrically. The results indicated that in the model turbidimetric immunoassay, ACRYLAT coated with HSA can be used for the detection of anti-HSA in the goat anti-HSA serum diluted from 50 to 7000-fold. Immobilization of rabbit antibodies to plasminogen (anti-Plg) to ACRYLAT via the epsilon-aminocaproic acid linkers provided particles which were used for the development of the turbidimetric immunoassay for plasminogen. In this assay plasminogen could be detected in concentration ranging from 0.75 to 75 micrograms ml-1 in the blood plasma.

  18. Further investigations of the properties of polymer modified cements

    International Nuclear Information System (INIS)

    Johnson, D.I.

    1988-05-01

    This report concludes the work done on behalf of the Department of the Environment on polymer modified cement composites. Topics covered include: the influence of cure schedule on flexural properties, observation of the onset and cracking during flexural testing, measurement of water permeability and caesium diffusion rates, and the use of Back Scattered Electron Imaging to identify the polymer phase. The properties of epoxide resin modified cements in the previous report were disappointing. Air entrainment of the mixing stage was a likely cause of the poor performance of these products and procedures to overcome this problem were devised. The range of polymer additives investigated was broadened by the inclusion of modified acrylic latexes and a polymensable acrylate resin additive. Properties for OPC and 9 BFS: 1 OPC cements are compared and the modification of properties achieved by polymer additions to both cement systems is discussed. (author)

  19. Thermal-kinetic study of natural rubber latex films vulcanized by using gamma radiation; Estudo termo-cinetico de filmes de latex de borracha natural de Hevea brasiliensis vulcanizada por radiacao gama

    Energy Technology Data Exchange (ETDEWEB)

    Leal, Ana Paula Pinho Rodrigues; Barros, Glaucione Gomes de [Brasilia Univ., DF (Brazil). Inst. de Quimica; Guedes, Selma M.L. [Instituto de Pesquisa em Energia Nuclear, Sao Paulo, SP (Brazil)

    1999-07-01

    Vulcanization of natural rubber latex by ionization radiation produces the crosslink in disperse latex particles. Advantages over conventional process of vulcanization are: the absence of carcinogenic nitrosamines, low cytotoxicity and better degradation at room conditions, due to mainly to the absence of sulfur, zinc oxide and dithiocarbamates. Thermogravimetric analysis (TG) is the measurement of the weight change of a material as a function of temperature and time. TG data different heat speed provide an alternative model of the kinetics of degradation of polymeric materials. The kinetic studies of this material showed a single degradation process at least for 76,5% of mass loss. The activation energy was 49 Kcal/mol. For higher mass loss (85%) the degradation was characterized by associate mechanism. (author)

  20. Technology of Anticorrosive Protection of Steel Constructions by Coatings Based on Rapid-Hardening Bitumen-Latex Emulsion

    Directory of Open Access Journals (Sweden)

    Nykyforchyn, H.M.

    2016-01-01

    Full Text Available The recipes of rapid-hardening bitumen-latex emulsions and coatings on its base are created, in-laboratory tests of their physical, chemical and anticorrosive properties are carried out. The technology of anticorrosive protection and the installation technical documentation for making of aqueous bitumen-latex emulsion is developed, installation is mounted and a pilot lot of rapid-hardening emulsion is produced. Experimental-industrial approbation of the technology of coating formation on pipes in oil and gas industry is carried out.

  1. Isolation of natural inhibitors of papain obtained from Carica papaya latex

    Directory of Open Access Journals (Sweden)

    Rubens Monti

    2004-09-01

    Full Text Available Studies were carried out to natural papain inhibitor from papaya latex. Fresh latex from green fruits of Carica papaya was collected and immediately transported in ice bath to the lab, from which three fractions with inhibitor effect of esterase papain activity were isolated by latex dialysis, Sephadex G-25 gel filtration and ionic exchange chromatography in SP-Sephadex C-25. The isolated fractions, identified as inhibitors I and II, showed a negative reaction with ninhydrin; however, the fraction identified as P-III showed positive reaction with ninhydrin. Kinetics data showed non-competitive inhibition (inhibitor I and uncompetitive (inhibitors II and P-III.Este trabalho apresenta novos dados sobre inibidores naturais de papaína. O látex fresco de frutos verdes de Carica papaya foi coletado pela manhã em plantações da região de Araraquara, SP, Brasil e imediatamente transportado ao laboratório em banho de gelo. Três frações com efeito inibitório da atividade esterásica da papaína foram isoladas a partir do látex fresco, através de diálise, filtração em Sephadex G-25 e cromatografia em SP-Sephadex C-25. As frações isoladas identificadas como inibidores I e II, mostraram reação negativa à ninidrina; entretanto, a fração identificada como P-III mostrou reação positiva. Dados cinéticos revelaram inibição não-competitiva (inibidor I e incompetitiva (inibidores II e P-III.

  2. Naturally cured foamed concrete with improved thermal insulation properties

    Directory of Open Access Journals (Sweden)

    Mashkin Nikolay

    2018-01-01

    Full Text Available The paper is dedicated to investigation on improvement of thermal insulation properties of non-autoclaved concrete by increasing aggregate stability of foamed concrete mixture. The study demonstrates influence of mineral admixtures on the foam stability index in the mortar mixture and on decrease of foamed concrete density and thermal conductivity. The effect of mineral admixtures on thermal conductivity properties of non-autoclaved concrete was assessed through different ways of their addition: to the foam and to the mortar mixture. The admixtures were milled up to the specific surface area of 300 and 600 m2/kg using an AГO-9 centrifugal attrition mill with continuous operation mode (Institute of Solid State Chemistry and Mechanochemistry, Siberian Branch of the Russian Academy of Sciences, Novosibirsk. Laboratory turbulent foam concrete mixer was used to prepare foamed concrete. Thermal conductivity coefficient was defined by a quick method using “ИTП-MГ 4 “Zond” thermal conductivity meter in accordance with the regulatory documents. The impact of modifiers on the foam structure stability was defined using the foam stability index for the mortar mixture. The research demonstrated the increase in stability of porous structure of non-autoclaved concrete when adding wollastonite and diopside. Improvement of thermal and physical properties was demonstrated, the decrease of thermal conductivity coefficient reaches 0.069 W/(m×°C

  3. Conceptual model for concrete long time degradation in a deep nuclear waste repository

    Energy Technology Data Exchange (ETDEWEB)

    Lagerblad, B; Traegaardh, J [Swedish Cement and Concrete Research Inst., Stockholm (Sweden)

    1994-02-01

    This report is mainly a state-of-the-art report of concrete long time durability in the environment expected in a deep site underground nuclear waste repository in Swedish crystalline bedrock. The report treats how the concrete and the surrounding groundwater will interact and how they will be affected by cement chemistry, type of aggregate etc. The different mechanisms for concrete alteration treated include sulphate attack, carbonation, chloride attack, alkali-silica reaction and leaching phenomena. In a long time perspective, the chemical alterations in concrete is mainly governed by the surrounding groundwater composition. After closure the composition of the groundwater will change character from a modified meteoric to a saline composition. Therefore two different simulated groundwater compositions have been used in modelling the chemical interaction between concrete and groundwater. The report also includes a study of old and historical concrete which show observations concerning recrystallization phenomena in concrete. 72 refs, 39 figs.

  4. Conceptual model for concrete long time degradation in a deep nuclear waste repository

    International Nuclear Information System (INIS)

    Lagerblad, B.; Traegaardh, J.

    1994-02-01

    This report is mainly a state-of-the-art report of concrete long time durability in the environment expected in a deep site underground nuclear waste repository in Swedish crystalline bedrock. The report treats how the concrete and the surrounding groundwater will interact and how they will be affected by cement chemistry, type of aggregate etc. The different mechanisms for concrete alteration treated include sulphate attack, carbonation, chloride attack, alkali-silica reaction and leaching phenomena. In a long time perspective, the chemical alterations in concrete is mainly governed by the surrounding groundwater composition. After closure the composition of the groundwater will change character from a modified meteoric to a saline composition. Therefore two different simulated groundwater compositions have been used in modelling the chemical interaction between concrete and groundwater. The report also includes a study of old and historical concrete which show observations concerning recrystallization phenomena in concrete. 72 refs, 39 figs

  5. Beta induced Bremsstrahlung dose rate in concrete shielding

    International Nuclear Information System (INIS)

    Manjunatha, H.C.

    2013-01-01

    Dosimetric study of beta-induced Bremsstrahlung in concrete is importance in the field of radiation protection. The efficiency, intensity and dose rate of beta induced Bremsstrahlung by 113 pure beta nuclides in concrete shielding is computed. The Bremsstrahlung dosimetric parameters such as the efficiency (yield), Intensity and dose rate of Bremsstrahlung are low for 199 Au and high for 104 Tc in concrete. The efficiency, Intensity and dose rate of Bremsstrahlung increases with maximum energy of beta nuclide (Emax) and modified atomic number (Zmod) of the target. The estimated Bremsstrahlung efficiency, Intensity and dose rate are useful in the calculations photon track-length distributions. These parameters are useful to determine the quality and quantity of the radiation (known as the source term). Precise estimation of this source term is very important in planning of radiation shielding. (author)

  6. Natural membranes of Hevea brasiliensis latex as delivery system for Casearia sylvestris leaf components

    Directory of Open Access Journals (Sweden)

    Flávio A. Carvalho

    Full Text Available ABSTRACT Natural latex from Hevea brasiliensis (Wild. ex A.Juss Müll.Arg., Euphorbiaceae, showed angiogenic action and Casearia sylvestris Sw., Salicaceae, leaf derivatives presented anti-inflammatory and wound healing activities. Therefore, an association of these effects was interesting for wound healing applications. The aims of this study were the development of membranes of natural latex incorporated with C. sylvestris leaf derivatives (ethanolic extract, diterpene concentrated fraction and casearin J, their chemical and physical characterization, and the evaluation of in vitro skin permeation and retention of C. sylvestris bioactive secondary metabolites (diterpenes and phenolic compounds. The membranes were developed mixing hydroethanolic solutions of C. sylvestris derivatives with latex and drying them in a desiccator. They were characterized by infrared spectroscopy, scanning electron microscopy, water vapor permeability and mechanical resistance assays, demonstrating that all membranes were permeable, resistant and homogeneous in surfaces. The permeation and retention assays demonstrated dermal penetration of phenolic compounds for ethanolic extract membrane and of casearin-like clerodane diterpenes for all membranes, indicating that these membranes have great potential for therapeutical application as a topical system for C. sylvestris components releasing.

  7. Dragon Fruit Foliage Plant-Based Coagulant for Treatment of Concentrated Latex Effluent: Comparison of Treatment with Ferric Sulfate

    Directory of Open Access Journals (Sweden)

    Juferi Idris

    2013-01-01

    Full Text Available The effectiveness of dragon fruit foliage as a natural coagulant for treatment of concentrated latex effluent was investigated and compared with ferric sulfate, a chemical coagulant. Dragon fruit is a round and often red-colored fruit with scales-like texture and is native to south American countries which is also cultivated and heavily marketed in southeast Asian countries. Its foliage represents a part of its overall plant system. Latex effluent is one of the main byproduct from rubber processing factories in Malaysia. Three main parameters investigated were chemical oxygen demand (COD, suspended solids (SS, and turbidity of effluent. Coagulation experiments using jar test were performed with a flocculation system where the effects of latex effluent pH as well as coagulation dosage on coagulation effectiveness were examined. The highest recorded COD, SS, and turbidity removal percentages for foliage were observed for effluent pH 10 at 94.7, 88.9, and 99.7%, respectively. It is concluded that the foliage showed tremendous potential as a natural coagulant for water treatment purposes. The foliage could be used in the pretreatment stage of Malaysian latex effluent prior to secondary treatment.

  8. Banyan latex: a facile fuel for the multifunctional properties of MgO nanoparticles prepared via auto ignited combustion route

    International Nuclear Information System (INIS)

    Anil Kumar, M R; Nagaswarupa, H P; Gurushantha, K; Pratapkumar, C; Prashantha, S C; Shashishekar, T R; Anantharaju, K S; Nagabhushana, H; Sharma, S C; Vidya, Y S; Daruka Prasad, B; Vivek Babu, C S; Vishnu Mahesh, K R

    2015-01-01

    MgO nanoparticles (MNPs) were prepared by a solution combustion route using banyan tree (BT) latex and glycine as fuels. The powder x-ray diffraction results indicate the formation of a single cubic phase and the crystallite size obtained from transmission electron microscopy was found to be ∼10–15 nm. Scanning electron microscopy result reveals spherical-shaped particles obtained with BT latex. However, in a chemical route, porous and agglomerated particles were obtained. The energy band gap of MNPs obtained using BT latex and a chemical route were found to be in the range 4.85–5.0 eV. Photoluminescence peaks observed at 473, 514, and 588 nm when excited at 433 nm, which were attributed to surface defects. The enhanced photocatalytic activities of spherical MgO were due to smaller crystallite size, higher surface defects, dye sensitization, and capability to reduce the electron–hole pair recombination. Further, green-synthesized MNPs exhibit superior antifungal activity against various plant pathogens. The present studies demonstrated a green engineering route for the synthesis of multifunctional MNPs using BT latex. (paper)

  9. Fracture properties of high-strength concrete obtained by direct modification of structure

    Directory of Open Access Journals (Sweden)

    Solodkyy Serhiy

    2017-01-01

    Full Text Available High-strength concrete is effectively used worldwide in the last three decades, but it is more brittle in comparison with normal strength concretes. Partial substitution of cement in concrete by active mineral additives and usage of chemical admixture of plasticizing and air-entraining action can considerably change their fracture properties. The obtained results show that the increase of the fracture properties is observed in concretes modified with chemical admixtures incorporating mineral additives such as zeolite and limestone due to consolidation of the concrete microstructure. Densification takes place as a result of limiting the amount of calcium hydroxide (CH due to its reaction with active silica included in the zeolite and the formation of larger amounts of hydrated calcium silicates of tobermorite type as well as calcium hydroaluminate and hydrocarboaluminate with the simultaneous adsorption modification of hydrated products by chemical admixtures.

  10. Modified Hydrotalcites as Smart Additives for Improved Corrosion Protection of Reinforced Concrete

    NARCIS (Netherlands)

    Yang, Z.

    2015-01-01

    Corrosion of reinforcing steel is a major culprit to durability and serviceability of concrete structures. This problem is highly relevant for civil engineering structures in the transport sector, such as bridges, tunnels, harbour quays and parking structures. The dominant aggressive external

  11. Mechanism of n-butyl acrylate sensitization action in radiation vulcanization of natural rubber latex

    International Nuclear Information System (INIS)

    Sabharwal, S.; Chaudhari, C.V.; Bhardwaj, Y.K.; Majali, A.B.; Das, T.N.

    1996-01-01

    In order to understand the role of n-butyl acrylate (nBA) in radiation vulcanization of natural rubber latex, pulse radiolysis technique has been utilized to study the reactions of the transient species produced by reaction of OH . , e- aq and H . atoms with nBA in aqueous solutions. The results show that transients produced by reaction of e- aq with nBA alone are capable of propagating the polymerization reaction and enhance the vulcanization process. These results have been further confirmed by studying the effect of electron scavengers on the vulcanization behaviour of natural rubber latex in presence of nBA. (author). 3 refs., 3 figs

  12. Improving the Bond Strength of Rice Husk Ash Concrete by Incorporating Polymer: A New Approach

    Directory of Open Access Journals (Sweden)

    D. K. Bangwar

    2018-02-01

    Full Text Available This paper gives an insight of how to improve the bond strength of cement in which concrete is replaced with rice husk ash. A concrete mix was prepared and was used in different types of mixes i.e. Control Mix, 10% cement substituted concrete with rice husk ash and polymer modified concrete by incorporation different dosages of polymer in the 10% cement substituted concrete. A bar of 12mm diameter, 300mm in length was placed in the center of the cylindrical specimens for pull out test. It was observed that the bond strength between concrete and steel decreases with the replacement of cement with ash, conversely the bond strength improves with the addition of polymer dosages.

  13. TRANSPARENT CONCRETE

    OpenAIRE

    Sandeep Sharma*, Dr. O.P. Reddy

    2017-01-01

    Transparent concrete is the new type of concrete introduced in todays world which carries special property of light transmitting due to presence of light Optical fibres. Which is also known as translucent concrete or light transmitting concrete, it is achieved by replacing coarse aggregates with transparent alternate materials (Optical fibres). The binding material in transparent concrete may be able to transmit light by using clear resins the concrete mix. The concrete used in industry in pr...

  14. Effect of PVA fiber content on creep property of fiber reinforced high-strength concrete columns

    Science.gov (United States)

    Xu, Zongnan; Wang, Tao; Wang, Weilun

    2018-04-01

    The effect of PVA (polyvinyl alcohol) fiber content on the creep property of fiber reinforced high-strength concrete columns was investigated. The correction factor of PVA fiber content was proposed and the creep prediction model of ACI209 was modified. Controlling the concrete strength as C80, changing the content of PVA fiber (volume fraction 0%, 0.25%, 0.5%, 1% respectively), the creep experiment of PVA fiber reinforced concrete columns was carried out, the creep coefficient of each specimen was calculated to characterize the creep property. The influence of PVA fiber content on the creep property was analyzed based on the creep coefficient and the calculation results of several frequently used creep prediction models. The correction factor of PVA fiber content was proposed to modify the ACI209 creep prediction model.

  15. Properties and Characterization of Kenaf-Filled Natural Rubber Latex Foam

    Directory of Open Access Journals (Sweden)

    Ahmad Fikri Abdul Karim

    2015-12-01

    Full Text Available Kenaf powder was incorporated with natural rubber latex (NRL compound and foamed to make natural rubber latex foam (NRLF by using a well known technique called the Dunlop method. Different loadings of kenaf powder were added to NRL compound and was foamed to make NRLF. The mechanical properties, density, compression, thermal, and micro-structural characterization of control NRLF and kenaf incorporated NRLF were studied. Increasing content of kenaf reduced the tensile strength, elongation at break, and compressive strength of a NRLF. Modulus at 100% elongation and density of the NRLF increased with an increase in filler loading. Higher kenaf loading indicated higher elasticity of kenaf-filled NRLF, but the recovery percentage of kenaf-filled NRLF decreased with increasing kenaf loading. From thermogravimetric analysis (TGA result, an increase in the amount of kenaf loading from 1 to 7 phr increased the thermal stability of kenaf-filled NRLF. Morphological and micro-structural characterization performed by using scanning electron microscopy (SEM showed that kenaf powder filled up the micro-sized pores in the open cell structure of kenaf-filled NRLF.

  16. Identification, quantification, spatiotemporal distribution and genetic variation of major latex secondary metabolites in the common dandelion (Taraxacum officinale agg.).

    Science.gov (United States)

    Huber, Meret; Triebwasser-Freese, Daniella; Reichelt, Michael; Heiling, Sven; Paetz, Christian; Chandran, Jima N; Bartram, Stefan; Schneider, Bernd; Gershenzon, Jonathan; Erb, Matthias

    2015-07-01

    The secondary metabolites in the roots, leaves and flowers of the common dandelion (Taraxacum officinale agg.) have been studied in detail. However, little is known about the specific constituents of the plant's highly specialized laticifer cells. Using a combination of liquid and gas chromatography, mass spectrometry and nuclear magnetic resonance spectrometry, we identified and quantified the major secondary metabolites in the latex of different organs across different growth stages in three genotypes, and tested the activity of the metabolites against the generalist root herbivore Diabrotica balteata. We found that common dandelion latex is dominated by three classes of secondary metabolites: phenolic inositol esters (PIEs), triterpene acetates (TritAc) and the sesquiterpene lactone taraxinic acid β-D-glucopyranosyl ester (TA-G). Purification and absolute quantification revealed concentrations in the upper mgg(-1) range for all compound classes with up to 6% PIEs, 5% TritAc and 7% TA-G per gram latex fresh weight. Contrary to typical secondary metabolite patterns, concentrations of all three classes increased with plant age. The highest concentrations were measured in the main root. PIE profiles differed both quantitatively and qualitatively between plant genotypes, whereas TritAc and TA-G differed only quantitatively. Metabolite concentrations were positively correlated within and between the different compound classes, indicating tight biosynthetic co-regulation. Latex metabolite extracts strongly repelled D. balteata larvae, suggesting that the latex constituents are biologically active. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. texreg: Conversion of Statistical Model Output in R to LATEX and HTML Tables

    Directory of Open Access Journals (Sweden)

    Philip Leifeld

    2013-11-01

    Full Text Available A recurrent task in applied statistics is the (mostly manual preparation of model output for inclusion in LATEX, Microsoft Word, or HTML documents usually with more than one model presented in a single table along with several goodness-of-fit statistics. However, statistical models in R have diverse object structures and summary methods, which makes this process cumbersome. This article first develops a set of guidelines for converting statistical model output to LATEX and HTML tables, then assesses to what extent existing packages meet these requirements, and finally presents the texreg package as a solution that meets all of the criteria set out in the beginning. After providing various usage examples, a blueprint for writing custom model extensions is proposed.

  18. Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

    Science.gov (United States)

    Määttänen, Anni; Ihalainen, Petri; Törngren, Björn; Rosqvist, Emil; Pesonen, Markus; Peltonen, Jouko

    2016-02-01

    Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV-vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH2)11OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal (optical and electrical) real-time monitoring of length-scale-dependent biomaterial-surface interactions.

  19. An evidence-based approach to medication preparation for the surgical patient at risk for latex allergy: is it time to stop being stopper poppers?

    Science.gov (United States)

    Heitz, James W; Bader, Stephen O

    2010-09-01

    The prevalence of latex allergy is increasing in surgical patient populations. Avoidance of exposure to the allergen is essential to minimizing perioperative complications in patients suspected to be at risk. Natural rubber latex has historically been ubiquitous in medical devices containing rubber. In 1998, the Food and Drug Administration (FDA) began to require the labeling of medical devices made from natural rubber latex; since that time substantial progress has been made in identifying latex-free alternatives. However, the rubber stoppers commonly found in pharmaceutical vial closures are exempt from FDA labeling requirements. Examination of the clinical and basic science literature regarding pharmaceutical vial closures supports limiting the rubber stopper to a single needle puncture as a safer practice, with the caveat that no strategy exists for the complete elimination of risk as long as stoppers made from natural rubber latex are used in pharmaceutical vials intended for human use. Copyright © 2010 Elsevier Inc. All rights reserved.

  20. Techniques and methods of characterization of admixtures for the concrete

    OpenAIRE

    Palacios, M.; Sierra, C.; Puertas, F.

    2003-01-01

    Admixtures are defined as those products that are incorporated in the moment of the process of mixture of the concrete in a quantity not bigger than 5 by mass of the cement %, with relationship to the cement content in the concrete, with object of modifying the properties of the mixture in .state fresh and/or hardened. The behaviour of the admixtures depends on its chemical and ionic composition, the organic functional groups present, and the structure of the polymer and the distribution of m...

  1. Finite element analysis of prestressed concrete reactor vessels

    International Nuclear Information System (INIS)

    Smith, P.D.; Cook, W.A.; Anderson, C.A.

    1977-01-01

    This paper discusses the development of a finite element code suitable for the safety analysis of prestressed concrete reactor vessels. The project has involved modification of a general purpose computer code to handle reinforced concrete structures as well as comparison of results obtained with the code against published experimental data. The NONSAP nonlinear structural analysis program was selected for the ease with which it can be modified to encompass problems peculiar to nuclear reactors. Pre- and post-processors have been developed for mesh generation and for graphical display of response variables. An out-of-core assembler and solver have been developed for the analysis of large three dimensional problems. The constitutive model for short term loads forms an orthotropic stress-strain relationship in which the concrete and the reinforcing steel are treated as a composite. The variation of stiffness and strength of concrete under multiaxial stress states is accounted for. Cracks are allowed to form at element integration points based on a three dimensional failure envelope in stress space. Composite tensile and shear properties across a crack are modified to account for bond degradation and for dowel action of the reinforcement. The constitutive law for creep is base on the expansion of the usual creep compliance function in the form of a Dirichlet exponential series. Empirical creep data are then fit to the Dirichlet series approximation by means of a least squares procedure. The incremental deformation process is subsequently reduced to a series of variable stiffness elasticity problems in which the past stress history is represented by a finite number of hidden material variables

  2. Concentrations, Stability, and Isolation of the Furan Fatty Acid 9-(3-Methyl-5-pentylfuran-2-yl)-nonanoic Acid from Disposable Latex Gloves.

    Science.gov (United States)

    Müller, Marco; Hogg, Melanie; Ulms, Kerstin; Vetter, Walter

    2017-09-13

    Because of their antioxidant properties, furan fatty acids (furan-FAs) are valuable minor compounds with a widespread occurrence in all living matter. Unfortunately, pure standards are not readily available, because they usually contribute only 1% to the lipid fraction. A known exception of this is the milky fluid of Hevea brasiliensis, commonly known as latex, in which the furan-FA 9-(3-methyl-5-pentylfuran-2-yl)-nonanoic acid (9M5) contributes about 90% to the triacylglycerides. In this study, we investigated the content of 9M5 in 30 different disposable latex gloves, which ranged from 0.7 to 8.2 mg/g of glove. The light degradability of 9M5 in latex gloves was investigated, and different amounts of 9M5 in disposable latex gloves were attributed to varying exposure time to light. Additionally, over 100 mg of the methyl or ethyl ester of 9M5 (purity of >98%) could be extracted from disposable latex gloves, employing cold extraction and silver ion chromatography. With this method, standards for the quantitation of furan-FAs are obtained easily and rapidly in all laboratories.

  3. How Concrete is Concrete

    Directory of Open Access Journals (Sweden)

    Koeno Gravemeijer

    2010-07-01

    Full Text Available If we want to make something concrete in mathematics education, we are inclined introduce, what we call, ‘manipulatives’, in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own, abstract, knowledge; in the latter, we try to find an example that the others will be familiar with. This article first looks at the tension between these two different ways of making things concrete. Next another role of manipulatives, will be discussed, namely that of means for scaffolding and communication. In this role, manipulatives may function as means of support in a process that aims at helping students to build on their own thinking while constructing more sophisticated mathematics

  4. The rapid determination of volatile fatty acid number in para rubber latex using fourier transform-near infrared spectroscopy based on quantification and discrimination model

    Directory of Open Access Journals (Sweden)

    Sureeporn Narongwongwattana

    2015-09-01

    Full Text Available Volatile Fatty Acid number (VFA no. is one of the parameters indicating the state of quality of Para rubber latex at that particular time. Most factories analyze this parameter using standard analytical method as in ISO 506:1992(E. Nevertheless, this procedure is complicated, chemical and time consuming, as well as skilled analyst required. Therefore, near infrared (NIR spectroscopy which is rapid, accurate and nonchemicals method was applied to determine the VFA no. in field latex and concentrated latex based on quantification and discriminant model. The best calibration equation was obtained from standard normal variate (SNV spectra in the region of 6109.7–5770.3, 4613.1–4242.9 cm-1 with R = 0.832, SECV = 0.036 and no bias. From the performance check, statistically it was found that SECV and bias were low enough for practical acceptance and the predicted VFA no. was not different significantly from actual VFA no. at 95% confidence intervals. In addition, discriminant model was developed to separate good quality latex from the deteriorated latex using VFA no. at 0.06 as standard as in ISO 2004:2010(E. The discriminant model can be used to screen the latex with overall accuracy of 91.86% in validation set.

  5. How Concrete is Concrete

    OpenAIRE

    Koeno Gravemeijer

    2010-01-01

    If we want to make something concrete in mathematics education, we are inclined introduce, what we call, ‘manipulatives’, in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own, abstract, knowledge; in the latter, we try to find an example that the others will be familiar with. This article first looks at the tension between these two diff...

  6. Effect of insulating concrete forms in concrete compresive strength

    Science.gov (United States)

    Martinez Jerez, Silvio R.

    The subject presented in this thesis is the effect of Insulating Concrete Forms (ICF's) on concrete compressive strength. This work seeks to identify if concrete cured in ICF's has an effect in compressive strength due to the thermal insulation provided by the forms. Modern construction is moving to energy efficient buildings and ICF's is becoming more popular in new developments. The thesis used a concrete mixture and a mortar mixture to investigate the effects of ICF's on concrete compressive strength. After the experimentations were performed, it was concluded that the ICF's do affect concrete strength. It was found that the forms increase concrete strength without the need for additional curing water. An increase of 50% in strength at 56 days was obtained. It was concluded that the longer concrete cures inside ICF's, the higher strength it reaches, and that ICF's effect on concrete strength is proportional to volume of concrete.

  7. Dynamics of ballistically injected latex particles in living human endothelial cells

    NARCIS (Netherlands)

    Li, Y.; Vanapalli Veera, V.S.A.R.; Vanapalli, Srinivas; Duits, Michael H.G.

    2009-01-01

    We studied the dynamics of ballistically injected latex particles (BIP) inside endothelial cells, using video particle tracking to measure the mean squared displacement (MSD) as a function of lag time. The MSD shows a plateau at short times and a linear behavior at longer times, indicating that the

  8. The criteria and the design of MINT's latex irradiator

    International Nuclear Information System (INIS)

    Razali Hamzah; Muhd Khairi Muhd Said; Muhd Ariff Hamzah; Wan Manshol Wan Zin; Wan Abd Hadi Wan Abu Bakar; Muhd Noor Muhd Yunus

    1996-01-01

    The demand for RVNRL is continually on the upsurge and the present irradiation technique at the present SINAGAMA plant is not sufficient and practical to meet the demand. A number of conceptual designs were evolved to design according to the requirements of cost-effective and highly efficient plant. The number of options are described. In 1994 MINT work with NUKEM to build an automatic continuous latex irradiation plant

  9. Deposition kinetics of quantum dots and polystyrene latex nanoparticles onto alumina: role of water chemistry and particle coating.

    Science.gov (United States)

    Quevedo, Ivan R; Olsson, Adam L J; Tufenkji, Nathalie

    2013-03-05

    A clear understanding of the factors controlling the deposition behavior of engineered nanoparticles (ENPs), such as quantum dots (QDs), is necessary for predicting their transport and fate in natural subsurface environments and in water filtration processes. A quartz crystal microbalance with dissipation monitoring (QCM-D) was used to study the effect of particle surface coatings and water chemistry on the deposition of commercial QDs onto Al2O3. Two carboxylated QDs (CdSe and CdTe) with different surface coatings were compared with two model nanoparticles: sulfate-functionalized (sPL) and carboxyl-modified (cPL) polystyrene latex. Deposition rates were assessed over a range of ionic strengths (IS) in simple electrolyte (KCl) and in electrolyte supplemented with two organic molecules found in natural waters; namely, humic acid and rhamnolipid. The Al2O3 collector used here is selected to be representative of oxide patches found on the surface of aquifer or filter grains. Deposition studies showed that ENP deposition rates on bare Al2O3 generally decreased with increasing salt concentration, with the exception of the polyacrylic-acid (PAA) coated CdTe QD which exhibited unique deposition behavior due to changes in the conformation of the PAA coating. QD deposition rates on bare Al2O3 were approximately 1 order of magnitude lower than those of the polystyrene latex nanoparticles, likely as a result of steric stabilization imparted by the QD surface coatings. Adsorption of humic acid or rhamnolipid on the Al2O3 surface resulted in charge reversal of the collector and subsequent reduction in the deposition rates of all ENPs. Moreover, the ratio of the two QCM-D output parameters, frequency and dissipation, revealed key structural information of the ENP-collector interface; namely, on bare Al2O3, the latex particles were rigidly attached as compared to the more loosely attached QDs. This study emphasizes the importance of considering the nature of ENP coatings as well

  10. Sequencing and characterization of asclepain f: the first cysteine peptidase cDNA cloned and expressed from Asclepias fruticosa latex.

    Science.gov (United States)

    Trejo, Sebastián A; López, Laura M I; Caffini, Néstor O; Natalucci, Claudia L; Canals, Francesc; Avilés, Francesc X

    2009-07-01

    Asclepain f is a papain-like protease previously isolated and characterized from latex of Asclepias fruticosa. This enzyme is a member of the C1 family of cysteine proteases that are synthesized as preproenzymes. The enzyme belongs to the alpha + beta class of proteins, with two disulfide bridges (Cys22-Cys63 and Cys56-Cys95) in the alpha domain, and another one (Cys150-Cys201) in the beta domain, as was determined by molecular modeling. A full-length 1,152 bp cDNA was cloned by RT-RACE-PCR from latex mRNA. The sequence was predicted as an open reading frame of 340 amino acid residues, of which 16 residues belong to the signal peptide, 113 to the propeptide and 211 to the mature enzyme. The full-length cDNA was ligated to pPICZalpha vector and expressed in Pichia pastoris. Recombinant asclepain f showed endopeptidase activity on pGlu-Phe-Leu-p-nitroanilide and was identified by PMF-MALDI-TOF MS. Asclepain f is the first peptidase cloned and expressed from mRNA isolated from plant latex, confirming the presence of the preprocysteine peptidase in the latex.

  11. Evaluation of force degradation characteristics of orthodontic latex elastics in vitro and in vivo.

    Science.gov (United States)

    Wang, Tong; Zhou, Gang; Tan, Xianfeng; Dong, Yaojun

    2007-07-01

    To evaluate the characteristics of force degradation of latex elastics in clinical applications and in vitro studies. Samples of 3/16-inch latex elastics were investigated, and 12 students between the ages of 12 and 15 years were selected for the intermaxillary and intramaxillary tractions. The elastics in the control groups were set in artificial saliva and dry room conditions and were stretched 20 mm. The repeated-measure two-way analysis of variance and nonlinear regression analysis were used to identify statistical significance. Overall, there were statistically significant differences between the different methods and observation intervals. At 24- and 48-hour time intervals, the force decreased during in vivo testing and in artificial saliva (P .05). In intermaxillary traction the percentage of initial force remaining after 48 hours was 61%. In intramaxillary traction and in artificial saliva the percentage of initial force remaining was 71%, and in room conditions 86% of initial force remained. Force degradation of latex elastics was different according to their environmental conditions. There was significantly more force degradation in intermaxillary traction than in intramaxillary traction. The dry room condition caused the least force loss. There were some differences among groups in the different times to start wearing elastics in intermaxillary traction but no significant differences in intramaxillary traction.

  12. Expression of VEGF and collagen using a latex biomembrane as bladder replacement in rabbits

    Directory of Open Access Journals (Sweden)

    André Luís Alonso Domingos

    2012-08-01

    Full Text Available OBJECTIVE: To investigate the VEGF expression and collagen deposition using a latex biomembrane as bladder replacement in rabbits. MATERIALS AND METHODS: After partial cystectomy, a patch of a non-vulcanized latex biomembrane (2 x 2 cm was sewn to the bladder of rabbits with 5/0 monofilament polydioxanone sulfate sutures in a watertight manner. Groups of 5 animals were killed at 15, 45 and 90 days after surgery and the bladder was removed. Sections of 5µm were cut and stained with picrosirius-red in order to estimate the amount of extracellular matrix in the graft. To confirm the presence of VEGF in tissues, protein expression was determined by immunohistochemistry. RESULTS: No death, urinary leakage or graft extrusion occurred in any group. All bladders showed a spherical shape. A progressive reduction in the amount of collagen occurred in the graft area and was negatively and linearly correlated with time (p < 0.001. VEGF expression was higher in grafted areas when compared to controls at 15 and 45 days after surgery and decreased with time (p < 0.001. CONCLUSION: The latex biomembrane as a matrix for partial bladder replacement in rabbits promotes temporary collagen deposition and stimulates the angiogenic process.

  13. Self-Placing Concrete

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    Certain concrete pours have areas where the congestion of reinforcing bars make placement of concrete almost impossible. Using conventional placing and vibration techniques, the resulting concrete can have considerable honeycombing due to the development of voids. Self-placing concrete is a possible solution to the problem. Also known as self-compactable concrete, self-consolidating concrete, flowable concrete, and non-vibration concrete. These concretes eliminate the need for vibration in a ...

  14. The effects of temperature and pH bacterial degradation of latex ...

    African Journals Online (AJOL)

    The goal of this study was to integrate the activities of paint deterioration of microbial communities (microcosms) on the basis of environmental factors. The effect of temperature and pH on bacterial degradation of latex paint under humid condition by bacterial isolates was studied. Results obtained revealed that paint ...

  15. Particle size, morphology and color tunable ZnO:Eu{sup 3+} nanophosphors via plant latex mediated green combustion synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Chandrasekhar, M. [Prof. C.N.R. Rao Centre for Advanced Materials, Tumkur University, Tumkur 572 103 (India); Department of Physics, Acharya Institute of Technology, Bangalore 560 107 (India); Nagabhushana, H., E-mail: bhushanvlc@gmail.com [Prof. C.N.R. Rao Centre for Advanced Materials, Tumkur University, Tumkur 572 103 (India); Sharma, S.C. [B.S. Narayan Centre of Excellence for Advanced Materials, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Department of Mechanical Engineering, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Sudheer kumar, K.H. [Department of Environmental Science, Kuvempu University, Shankarghatta, Shimoga 577 451 (India); Department of Chemistry, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); B.S. Narayan Centre of Excellence for Advanced Materials, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Dhananjaya, N. [Department of Physics, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); B.S. Narayan Centre of Excellence for Advanced Materials, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Sunitha, D.V. [Prof. C.N.R. Rao Centre for Advanced Materials, Tumkur University, Tumkur 572 103 (India); Shivakumara, C. [Solid State and Structural Chemistry Unit, Indian Institute of Science, Bangalore 560 012 (India); Nagabhushana, B.M. [Department of Chemistry, M.S. Ramaiah Institute of Technology, Bangalore 560 054 (India)

    2014-01-25

    Highlights: • ZnO:Eu{sup 3+} phosphors were prepared by green synthesis route. • Morphology and particle size was tuned by varying the concentration of plant latex. • The phosphor show excellent chromaticity coordinates in the white region. -- Abstract: Efficient ZnO:Eu{sup 3+} (1–11 mol%) nanophosphors were prepared for the first time by green synthesis route using Euphorbia tirucalli plant latex. The final products were well characterized by powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–visible spectroscopy (UV–Vis), Fourier transform infrared spectroscopy (FTIR), etc. The average particle size of ZnO:Eu{sup 3+} (7 mol%) was found to be in the range 27–47 nm. With increase of plant latex, the particle size was reduced and porous structure was converted to spherical shaped particles. Photoluminescence (PL) spectra indicated that the peaks situated at ∼590, 615, 648 and 702 nm were attributed to the {sup 5}D{sub 0} → {sup 7}F{sub j(j=1,2,3,4)} transitions of Eu{sup 3+} ions. The highest PL intensity was recorded for 7 mol% with Eu{sup 3+} ions and 26 ml plant latex concentration. The PL intensity increases with increase of plant latex concentration up to 30 ml and there after it decreases. The phosphor prepared by this method show spherical shaped particles, excellent chromaticity co-ordinates in the white light region which was highly useful for WLED’s. Further, present method was reliable, environmentally friendly and alternative to economical routes.

  16. EVALUATION OF CYTOTOXIC, ANTIMICROBIAL AND ANTIINFLAMMATORY PROPERTIES FROM THE LATEX OF IPOMEA STAPHYLINA

    Directory of Open Access Journals (Sweden)

    Prasanthi Narra

    2014-04-01

    Full Text Available The plant Ipomoea staphylina has been used in diverse traditional medication for the treatment of diseases and illness of human beings. The crude latex extract obtained from the stem of Ipomea staphylina was evaluated for cytotoxic, antimicrobial and wound healing properties. Cell viability and cytotoxicity assays such as Colony Formation method and Enzyme based methods that determined cell viability with a colorimetric method were performed to evaluate the medicinal properties of Ipomea staphylina. Similarly Microbiological Antibiotic Assay to determine the antimicrobial properties and wound healing properties were tested by determining the potent anti-inflammatory molecules that inhibited COX and LOX enzymes. Results showed that the latex crude extract of Ipomea staphylina showed potent Antimicrobial and Antiinflamatory properties, but the viability of the cells were unaffected.

  17. Mechanical and Physical Properties of Hydrophobized Lightweight Aggregate Concrete with Sewage Sludge.

    Science.gov (United States)

    Suchorab, Zbigniew; Barnat-Hunek, Danuta; Franus, Małgorzata; Łagód, Grzegorz

    2016-04-27

    This article is focused on lightweight aggregate-concrete modified by municipal sewage sludge and lightweight aggregate-concrete obtained from light aggregates. The article presents laboratory examinations of material physical parameters. Water absorptivity of the examined material was decreased by the admixture of water emulsion of reactive polysiloxanes. Water transport properties were determined using Time Domain Reflectometry, an indirect technique for moisture detection in porous media. Together with basic physical parameters, the heat conductivity coefficient λ was determined for both types of lightweight aggregate-concrete. Analysis of moisture and heat properties of the examined materials confirmed the usefulness of light aggregates supplemented with sewage sludge for prospective production.

  18. Adsorption of immunoglobulin G on core-shell latex particles precoated with chaps

    NARCIS (Netherlands)

    Giacomelli, CE; Vermeer, AWP; Norde, W

    2000-01-01

    The aim of this work is to investigate the adsorption behavior of a monoclonal antibody (immunoglobulin G, IgG) on latex particles, possessing reactive chloromethyl groups, precoated with 3-([3-cholamidopropyl]dimethylammonio-1-propansulfonate (Chaps). The amount and reactivity of the surface

  19. Adsorption of immunoglobulin G on core-shell latex particles precoated with chaps

    NARCIS (Netherlands)

    Giacomelli, C.E.; Vermeer, A.W.P.; Norde, W.

    2000-01-01

    The aim of this work is to investigate the adsorption behavior of a monoclonal antibody (immunoglobulin G, IgG) on latex particles, possessing reactive chloromethyl groups, precoated with 3-([3-cholamidopropyl]dimethylammonio-1-propanesulfonate (Chaps). The amount and reactivity of the surface

  20. Concrete

    DEFF Research Database (Denmark)

    2015-01-01

    Concrete is a component of coherent transition between a concrete base and a wooden construction. The structure is based on a quantity of investigations of the design possibilities that arise when combining digital fabrication tools and material capacities. Through tangible experiments the project...... specific for this to happen. And the knowledge and intention behind the drawing becomes specialised through the understanding of the fabrication processes and their affect on the materials.The structure Concrete is a result of a multi-angled kerf series in ash wood and a concrete base. The ash wood is cut...... using a 5-axis CNC router with a thin saw blade attached. The programming of the machining results in variations of kerfs that lets the ash wood twist into unique shapes.The shapes of the revolving ash ribbons continue into the concrete creating a cohesive shape. The form for the concrete itself is made...

  1. Efficiency of 1,9- Nonane-diol-diacrylate as a radiation vulcanization accelerator for natural rubber latex

    International Nuclear Information System (INIS)

    Haque, M.E.

    2003-09-01

    The efficiency of 1,9- Nonane-diol-diacrylate (NDDA) as a radiation vulcanization accelerator (RVA) for natural rubber latex (NRL) was investigated. Both gamma rays and electron beam (EB) were used for vulcanizing NRL with NDDA. The radiation dose of gamma rays, concentration of NDDA required to vulcanize the latex were optimized. 20 kGy radiation dose of gamma rays and 5 phr concentration of NDDA were found optimum to get maximum tensile and related properties. NRL was vulcanized under EB to find out the optimum condition of irradiation with this RVA. The defoamer concentrations, length of irradiation time under EB, concentration of RVA were optimizer by changing various parameters of the EB machine with a constant set of the others. 0.2 phr defoamer concentration, 30 minutes irradiation time and 5 phr concentration of NDDA were found optimum for irradiation of NRL under the EB machine. Effect of low current and optimum volume of latex charged in the reaction vessel suitable for vulcanization at a time were found out. (author)

  2. Build-up Factor Calculation for Ordinary Concrete, Baryte Concrete and Blast-furnace Slugges Concrete as γ Radiation Shielding

    International Nuclear Information System (INIS)

    Isman MT; Elisabeth Supriatni; Tochrul Binowo

    2002-01-01

    Calculation of build up factor ordinary concrete, baryte concrete and blast-furnace sludge concrete have been carried out. The calculations have been carried out by dose rate measurement of Cs 137 source before and after passing through shielding. The investigated variables were concrete type, thickness of concrete and relative possession of concrete. Concrete type variables are ordinary concrete, baryte concrete and blast sludge furnace concrete. The thickness variables were 6, 12, 18, 24, 30 and 36 cm. The relative position variables were dose to the source and close to detector. The result showed that concrete type and position did not have significant effect to build-up factor value, while the concrete thickness (r) and the attenuation coefficient (μ) were influenced to the build-up factor. The higher μr value the higher build-up factor value. (author)

  3. Radiation vulcanised natural rubber latex (RVNRL) market and challenges

    International Nuclear Information System (INIS)

    Wan Manshol Wan Zin; Najib Mohamad Zakey; Chai Chee Keong

    2000-01-01

    RVNRL has the required properties and proven useful for the manufacturing of examination gloves, balloons and finger cots at industrial scale. To date only RVNRL finger cots are available in the market. Problems and challenges for the market of other products are identified. Further success in the on going research activities will be the reference for more applications of RVNRL in the relevant industry to produce natural rubber latex products of more competitive values

  4. Reuse of waste iron as a partial replacement of sand in concrete.

    Science.gov (United States)

    Ismail, Zainab Z; Al-Hashmi, Enas A

    2008-11-01

    One of the major environmental issues in Iraq is the large quantity of waste iron resulting from the industrial sector which is deposited in domestic waste and in landfills. A series of 109 experiments and 586 tests were carried out in this study to examine the feasibility of reusing this waste iron in concrete. Overall, 130 kg of waste iron were reused to partially replace sand at 10%, 15%, and 20% in a total of 1703 kg concrete mixtures. The tests performed to evaluate waste-iron concrete quality included slump, fresh density, dry density, compressive strength, and flexural strength tests: 115 cubes of concrete were molded for the compressive strength and dry density tests, and 87 prisms were cast for the flexural strength tests. This work applied 3, 7, 14, and 28 days curing ages for the concrete mixes. The results confirm that reuse of solid waste material offers an approach to solving the pollution problems that arise from an accumulation of waste in a production site; in the meantime modified properties are added to the concrete. The results show that the concrete mixes made with waste iron had higher compressive strengths and flexural strengths than the plain concrete mixes.

  5. Shrinkage modeling of concrete reinforced by palm fibres in hot dry environments

    Science.gov (United States)

    Akchiche, Hamida; Kriker, Abdelouahed

    2017-02-01

    The cement materials, such as concrete and conventional mortar present very little resistance to traction and cracking, these hydraulic materials which induces large withdrawals on materials and cracks in structures. The hot dry environments such as: the Saharan regions of Algeria, Indeed, concrete structures in these regions are very fragile, and present high shrinkage. Strengthening of these materials by fibers can provide technical solutions for improving the mechanical performance. The aim of this study is firstly, to reduce the shrinkage of conventional concrete with its reinforcement with date palm fibers. In fact, Algeria has an extraordinary resources in natural fibers (from Palm, Abaca, Hemp) but without valorization in practical areas, especially in building materials. Secondly, to model the shrinkage behavior of concrete was reinforced by date palm fibers. In the literature, several models for still fiber concrete were founded but few are offers for natural fiber concretes. To do so, a still fiber concretes model of YOUNG - CHERN was used. According to the results, a reduction of shrinkage with reinforcement by date palm fibers was showed. A good ability of molding of shrinkage of date palm reinforced concrete with YOUNG - CHERN Modified model was obtained. In fact, a good correlation between experimental data and the model data was recorded.

  6. Study of the effect of ionizing radiation on the structure of natural rubber latex by positron annihilation technique

    International Nuclear Information System (INIS)

    Lopez Saldana, I.R.

    1993-01-01

    At the present research, were studied the changes in natural rubber latex structure, due to electron beam by a 3 MeV, 25 m A Dynamitron electron accelerator. The natural rubber latex was irradiated at 30, 40 and 50 kGy/s dose rate, over a total dose range from 150 to 250 kGy, for each dose rate used. From natural rubber latex irradiated films were prepared by casting with 0.7 mm. thickness. In the main part, the study was made by positron annihilation lifetime (PAL), this technique is unique in the determination of free-volume properties due to the fact that positronium atom (Ps) is found to be preferentially localized in the free-volume region of polymeric materials. The positron lifetime measurements were performing using a gamma-gamma coincidence system. These results were analyzed by PATFIT-88 program computer into three components, the long-lived component for orthopositronium (o-Ps) with parameters lifetime (τ 3 ) and formation intensity (I 3 ), were plotted and analyzed for each dose rate and total dose used. Besides with τ 3 were calculated the mean free-volume size based on the spherical model for the free-volume bubble, found that the free-volume decrease slightly with the total dose due to the crosslinking of natural rubber latex. Besides was studied the effect of dose rate on tensile strength, the tensile strength is increased with the total dose although there was not a clear effect due to the dose rate. Also the films were subjected to aging in order to determined the thermal stability of natural rubber latex irradiated, the results show that the films have good stability. Besides was used the infrared spectroscopy to determine the changes due to the crosslinking by variations in the characteristically absorption bands for cis 1,4-polyisoprene. (Author)

  7. Static properties and impact resistance of a green Ultra-High Performance Hybrid Fibre Reinforced Concrete (UHPHFRC) : experiments and modeling

    NARCIS (Netherlands)

    Yu, R.; Spiesz, P.R.; Brouwers, H.J.H.

    2014-01-01

    This paper addresses the static properties and impact resistance of a "green" Ultra-High Performance Hybrid Fibre Reinforced Concrete (UHPHFRC). The design of concrete mixtures aims to achieve a densely compacted cementitious matrix, employing the modified Andreasen & Andersen particle packing

  8. Costs and return analysis in rubber latex production in Edo State ...

    African Journals Online (AJOL)

    The study examined the costs and return analysis in rubber latex production in Edo Sate, Nigeria. Multi-stage sampling method was adopted to select 96 smallholder rubber framers for the study. The first stage was a purposive sampling of two LGAs and then simple random sampling of 6 villages each from the two LGA.

  9. Synthesis and characterization of poly (n-butyl acrylate)-poly (methyl methacrylate) latex interpenetrating polymer networks by radiation-induced seeded emulsion polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Yu Haibo [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Peng Jing [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China)], E-mail: jpeng@pku.edu.cn; Zhai Maolin; Li Jiuqiang; Wei Genshuan [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Qiao Jinliang [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); SINOPEC Beijing Research Institute of Chemical Industry, Beijing 100013 (China)

    2007-11-15

    A series of latex interpenetrating polymer networks (LIPNs) were prepared via a two-stage emulsion polymerization of methyl methacrylate (MMA) or mixture of MMA and n-butyl acrylate (n-BA) on crosslinked poly(n-butyl acrylate)(PBA) seed latex using {sup 60}Co {gamma}-ray radiation. The particles of resultant latex were produced with diameters between 150 and 250 nm. FTIR spectra identified the formation of crosslinked copolymers of PMMA or P(MMA-co-BA). Dynamic light scattering (DLS) showed that with increasing n-BA concentration in second-stage monomers, the particle size of LIPN increased. Transmission electron microscope(TEM) photographs showed that the morphology of resultant acrylate interpenetrating polymer network (IPN) latex varied from the distinct core-shell structure to homogenous particle structure with the increase of n-BA concentration, and the morphology was mainly controlled by the miscibility between crosslinked PBA seed and second-stage copolymers and polarity of P(MMA-co-BA)copolymers. In addition, differential scanning calorimeter (DSC) measurements indicated the existence of reinforced miscibility between PBA seed and P(MMA-co-BA)copolymer in prepared LIPNs.

  10. Synthesis of polymer hybrid latex poly(methyl methacrylate-co-butyl acrylate) with organo montmorillonite via miniemulsion polymerization method for barrier paper

    Science.gov (United States)

    Chanra, J.; Budianto, E.; Soegijono, B.

    2018-03-01

    Hybrid polymer latex based on combination of organic-inorganic materials, poly(methyl methacrylate-co-butyl acrylate) (PMMBA) and organo-montmorillonite (OMMT) were synthesized via miniemulsion polymerization technique. Modification of montmorillonite (MMT) through the incorporation of myristyltrimethylammonium bromide (MTAB) into the clay’s interlayer spaces were investigated by Small-Angle X-ray Scattering (SAXS), Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA) and Transmission Electron Microscopy (TEM). Barrier property and thermal stability of polymer latex film sample were investigated through its Water Vapor Transmission Rate (WVTR) and Thermogravimetric Analysis (TGA). The results indicated that addition of OMMT as filler in PMMBA increased the barrier property and thermal stability of the latex film. Addition of 8.0% (wt) OMMT increased the barrier property and thermal stability. Miniemusion polymerization process with higher addition (>8.0 wt%) of OMMT resulting in high latex viscosity, particle size, and high amount of coagulum. The utilization of this hybrid polymer could benefits paper and board industries to produce high quality barrier paper for food packaging.

  11. Caracterização da hipersensibilidade a luvas de látex em profissionais da odontologia = Rubber latex gloves hypersensitivities in dental workers

    Directory of Open Access Journals (Sweden)

    Flávia Sukekava

    2007-01-01

    Full Text Available As reações alérgicas ao látex vêm aumentando em profissionais da saúde e se manifestam como um incômodo local ou sintomatologia sistêmica. Para conhecer a freqüência das manifestações alérgicas nos usuários de luvas de látex foi realizada busca entre os profissionais da odontologia via aplicação de questionários. Foram aplicados 450questionários e, dentre os respondedores (140, 19% relataram manifestar reações locais ao contato com as luvas de látex e 5% reações sistêmicas a outros produtos de látex. Cerca de 2,5% declararam dermatite de contato e reações sistêmicas (anafiláticas, 1,5% apenas dermatite de contato e 1% sintomas de anafilaxia ao uso das luvas. Vinte por cento dos profissionais atenderam pacientes com alergia ao látex e 29% declararam questionar, durante a anamnese, a respeito de alergia ao látex. As reações alérgicas a luvas de látex foram freqüentes e é objeto de preocupação entre os profissionais da odontologia.Allergic reactions to natural rubber latex have increased in dental practice affecting both the professional and the patients. Allergic reactions may range from skin disease to asthma and anaphylaxis. This study aimed at determining the incidence of latex gloves allergy amongdental care workers. 450 allergy questionnaires were used to collect information on latex gloves reactions and 140 dental works answered them. Latex gloves reaction occurred in 19% of them and 5% reported allergic reactions to other latex products. 2.5% reported symptoms suggesting contact dermatitis and anaphylaxis hypersensitivities, 1.5% contact dermatitis, and 1% reported anaphylaxis symptoms when wearing them. 20% of them had patients who presented symptoms suggestive of anaphylaxis hypersensitivity to rubber gloves latex. Our study confirms that rubber latex gloves reactions are frequent among dental care workers, and dentists must be aware of the latex allergy in dental practice.

  12. Autogenous healing of cracks in concrete and its relevance to radwaste repositories

    International Nuclear Information System (INIS)

    Guppy, R.

    1988-03-01

    Cracks in concrete structures within a radioactive waste repository could provide fast transport pathways and as such could impair the performance of the concrete as a barrier to radionuclide migration. It has been widely reported that cracks in concrete can heal and, therefore, the evidence in support of this phenomenon has been reviewed and its relevance to a concrete barrier in a radioactive waste repository assessed. The mechanism of crack healing is not understood, but the most likely process responsible is calcite formation under wet conditions. There is doubt concerning whether the conditions in a repository will be suitable for crack healing; especially if the cement is extensively modified with slag or fuel ash. It is concluded that further experimental work is required to assess the impact of this phenomenon on the behaviour of cracks in repositories. (author)

  13. Effect of Hevea brasiliensis latex sap gel on healing of acute skin wounds induced on the back of rats

    Directory of Open Access Journals (Sweden)

    Maria Vitória Carmo Penhavel

    Full Text Available Objective : to evaluate the effect of topical delivery of latex cream-gel in acute cutaneous wounds induced on the back of rats. Methods : we subjected sixteen rats to dermo-epidermal excision of a round dorsal skin flap, with 2.5cm diameter. We divided the animals into two groups: Latex Group: application of cream-gel-based latex throughout the wound bed on postoperative days zero, three, six and nine; Control group: no treatment on the wound. Photographs of the lesions were taken on the procedure day and on the 6th and 14th postoperative days, for analyzing the area and the larger diameter of the wound. We carried out euthanasia of all animals on the 14th postoperative day, when we resected he dorsal skin and the underlying muscle layer supporting the wound for histopathological study. Results : there was no statistically significant difference in the percentage of wound closure, in the histopathological findings or in the reduction of the area and of the largest diameter of the wounds among the groups studied on the 14th postoperative day. Conclusion : according to the experimental conditions in which the study was conducted, latex cream-gel did not interfere in the healing of acute cutaneous wounds in rats.

  14. NMR relaxation times of natural rubber latex

    International Nuclear Information System (INIS)

    Harun, S.; Aziz, H.; Basir, Z.

    1994-01-01

    NMR relaxation times T sub 1 and T sub 2 of natural rubber latex have been measured at 25 degree C on a pulsed NMR spectrometer. The work focuses on the variation of the relaxation times with the amount of water content from 0% to 50%. The water content was adjusted by centrifuging and removing a certain amount of water from the sample. The data were analysed using a biexponential fitting procedure which yields simultaneously either T sub 1a and T sub 1b or T sub 2a and T sub 2b. The amount of solid was compared with the known amount of dry rubber content

  15. High Performance Concrete

    Directory of Open Access Journals (Sweden)

    Traian Oneţ

    2009-01-01

    Full Text Available The paper presents the last studies and researches accomplished in Cluj-Napoca related to high performance concrete, high strength concrete and self compacting concrete. The purpose of this paper is to raid upon the advantages and inconveniences when a particular concrete type is used. Two concrete recipes are presented, namely for the concrete used in rigid pavement for roads and another one for self-compacting concrete.

  16. Influence Of The Gripping Fixture On The Modified Compact Tension Test Results: Evaluation Of The Experiments On Cylindrical Concrete Specimens

    Directory of Open Access Journals (Sweden)

    Holušová Táňa

    2015-12-01

    Full Text Available The modified compact tension test (MCT might become in the future a stable test configuration for the evaluation of fracture-mechanics parameters or also for description of fatigue behavior of composites materials such as concrete. Core drilling is used for sampling of existing structures. These samples have cylindrical shape with the selected thickness to avoid the stress concentration. This contribution focuses on the evaluation of the fracture behavior during static and quasi static tests. Static tests are performed on standard specimen with diameter 150 mm and length 300 mm. The quasi-static tests are performed using two different gripping fixtures. The results for quasi-static tests are represented as L-COD diagrams (i.e. load vs. crack opening displacement measured on the loading axis. The comparison of results and discussion of advantages and disadvantages are introduced.

  17. How Concrete is Concrete?

    Directory of Open Access Journals (Sweden)

    Koeno Gravemeijer

    2011-01-01

    Full Text Available If we want to make something concrete in mathematics education, we are inclined introduce, what we call, ‘manipulatives’, in the form of tactile objects or visual representations. If we want to make something concrete in a everyday-life conversation, we look for an example. In the former, we try to make a concrete model of our own, abstract, knowledge; in the latter, we try to find an example that the others will be familiar with. This article first looks at the tension between these two different ways of making things concrete. Next another role of manipulatives, will be discussed, namely that of means for scaffolding and communication. In this role, manipulatives may function as means of support in a process that aims at helping students to build on their own thinking while constructing more sophisticated mathematics.Key words:  Conceret Learning Materials, School Math, Common Sense, Scaffolding, Communication DOI: http://dx.doi.org/10.22342/jme.2.1.780.1-14

  18. Properties of high-workability concrete with recycled concrete aggregate

    OpenAIRE

    Safiuddin,; Alengaram,Ubagaram Johnson; Salam,Abdus; Jumaat,Mohd Zamin; Jaafar,Fahrol Fadhli; Saad,Hawa Binti

    2011-01-01

    This study presents the effects of recycled concrete aggregate (RCA) on the key fresh and hardened properties of concrete. RCA was used to produce high-workability concrete substituting 0-100% natural coarse aggregate (NCA) by weight. The slump and slump flow of fresh concretes were determined to ensure high workability. In addition, the compressive, flexural and splitting tensile strengths, modulus of elasticity, and permeable voids of hardened concretes were determined. The test results rev...

  19. Effect of Dolomite as Expansive Agent and Shrinkage Reducing Admixture in Self-Compacting Shrinkage – Compensating Concrete

    OpenAIRE

    Qosai Sahib Radi Marshdi; Ahlam Hamid Jasim; Haider Abass Obeed

    2018-01-01

    The principle of using expansive agents has been recommended to manufacture shrinkage compensating concrete provided that an adequate wet curing is carried out. On the other hand, shrinkage-reducing admixture (SRA) in the concrete mixes, has been more recently suggested to reduce the risk of cracking in concrete structures caused by drying shrinkage. This paper is devoted to the study of the influence of complex modifier in the form of superplasticizer, shrinkage reducing admixture and e...

  20. Preliminary Investigation into Tree Dryness in Hevea brasiliensis (Wild. Ex Adr. De Juss Muell. Arg. by Path Analysis of Tree Dryness and Latex Parameters

    Directory of Open Access Journals (Sweden)

    Omokhafe, KO.

    2001-01-01

    Full Text Available The correlative path analysis between tree dryness and four latex parameters was studied in eleven clones of Hevea brasiliensis. The latex parameters used for evaluation were initial volume, initial flow rate, final volume and plugging index with tree dryness as the dependent factor. Estimates of direct and indirect effects of each of the latex parameters on tree dryness were calculated through linear correlation and path analysis. The correlation coefficient between initial volume and initial flow rate was 1.00 and both characters had the same correlation coefficients with other latex parameters and tree dryness. This implies that initial volume and initial flow rate are alternatives for evaluation of correlation between latex parameters and tree dryness. There was significant correlation between initial volume, initial flow rate and tree dryness at V = -0.52 and high indirect effect of initial volume and initial flow rate through final volume. In addition, despite the low correlation coefficient of V = -0.20 between final volume and tree dryness, the direct effect of final volume on tree dryness was high at 0.812. Final volume is therefore an important factor in the incidence of tree dryness.

  1. Structural Precast Concrete Handbook

    DEFF Research Database (Denmark)

    Kjærbye, Per Oluf H

    Structural concept for precast concrete systems. Design og precast reinforced concrete components. Design of precast concrete connections. Illustrations on design of precast concrete buildings. Precast concrete assembly.......Structural concept for precast concrete systems. Design og precast reinforced concrete components. Design of precast concrete connections. Illustrations on design of precast concrete buildings. Precast concrete assembly....

  2. COMPARATIVE STUDY OF GLASS FIBRE CONCRETE AND NORMAL CONCRETE

    OpenAIRE

    Mr.Yogesh S.Lanjewar*

    2018-01-01

    Concrete is basically the most important material concerning with the construction and infrastructural procedures, for which it should be of good strength and durability. Many researches are being conducted to make concrete more sustainable and of more strength and durability. Therefore keeping this in mind i have chosen to do the comparative study regarding the strength of normal concrete with the glass fibre added concrete using mix design procedure as per IS 10262-2009 for concrete. As w...

  3. Study of technological features of tubular compressed concrete members in concreting

    Directory of Open Access Journals (Sweden)

    Voskobiinyk Olena

    2017-01-01

    Full Text Available The technological features of core concreting were analyzed as the main factor in ensuring of strength and reliability of compressed concrete-filled steel tubular (CFST members. We have conducted the analysis of existing concreting methods of CFST members. In this respect, the most dangerous types of possible technological defects of concrete core of CFST members are inhomogeneity along the height, voids, caverns, and concrete “weak spots”. The authors considered the influence of such technological factors of concreting: placeability, time, concrete mixture compaction method, concreting height on the concrete core strength of CFST members. Based on the experimental studies conducted we suggested the regression correlations for determining the concrete strength of CFST members of different length depending on the movability of concrete mixture and a time for its compaction. The authors performed the correlation analysis of technological factors of concreting on the strength of the concrete core. We carried out the comparison of data on the concrete core strength of CFST members, that were determined by non-destructive methods (sclerometer test results, ultrasonic method and direct compression strength tests. We experimentally proved that using movable mixtures with the slump of about 4 – 9 cm the overall variation coefficient of concrete core strength of CFST members along the height reaches nearly 13%. Based on the experimental studies conducted we suggested the guidelines on optimal regimes of concrete compaction during manufacturing CFST members at a construction site environment.

  4. Deproteinised natural rubber latex grafted poly(dimethylaminoethyl methacrylate) - poly(vinyl alcohol) blend membranes: Synthesis, properties and application.

    Science.gov (United States)

    Jayadevan, Janisha; Alex, Rosamma; Gopalakrishnapanicker, Unnikrishnan

    2018-02-01

    Natural rubber latex was initially deproteinised (DNRL) and then subjected to physicochemical modifications to make high functional membranes for drug delivery applications. Initially, DNRL was prepared by incubating with urea, sodiumdodecylsulphate and acetone followed by centrifugation. The deproteinisation was confirmed by CHN analysis. The DNRL was then chemically modified by grafting (dimethylaminoethyl methacrylate) onto NR particles by using a redox initiator system viz; cumene hydroperoxide/tetraethylenepentamine, followed by dialysis for purification. The grafting was confirmed by dynamic light scattering, Fourier transform infrared spectroscopy and nuclear magnetic resonance spectroscopy. The grafted system was blended with a hydrophilic adhesive polymer PVA and casted into membranes. The membranes after blending showed enhanced mechanical properties with a threshold concentration of PVA. The moisture uptake, swelling and water contact angle experiments indicated an increased hydrophilicity with an increased PVA content in the blend membranes. The grafted DNRL possessed significant antibacterial property which has been found to be retained in the blended form. A notable decrease in cytotoxicity was observed for the modified DNRL membranes than the bare DNRL membranes. The in-vitro drug release studies using rhodamine B as a model drug, confirmed the utility of the prepared membranes to function as a drug delivery matrix. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Antimalarial Activity of the Chemical Constituents of the Leaf Latex of Aloe pulcherrima Gilbert and Sebsebe.

    Science.gov (United States)

    Teka, Tekleab; Bisrat, Daniel; Yeshak, Mariamawit Yonathan; Asres, Kaleab

    2016-10-28

    Malaria is one of the three major global public health threats due to a wide spread resistance of the parasites to the standard antimalarial drugs. Considering this growing problem, the ethnomedicinal approach in the search for new antimalarial drugs from plant sources has proven to be more effective and inexpensive. The leaves of Aloe pulcherrima Gilbert and Sebsebe, an endemic Ethiopian plant, are locally used for the treatment of malaria and other infectious diseases. Application of the leaf latex of A. pulcherrima on preparative silica gel TLC led to the isolation of two C -glycosylated anthrones, identified as nataloin ( 1 ) and 7-hydroxyaloin ( 2 ) by spectroscopic techniques (UV, IR, ¹H- and 13 C-NMR, HR-ESIMS). Both the latex and isolated compounds displayed antimalarial activity in a dose-independent manner using a four-day suppressive test, with the highest percent suppression of 56.2% achieved at 200 mg/kg/day for 2 . The results indicate that both the leaf latex of A. pulcherrima and its two major constituents are endowed with antiplasmodial activities, which support the traditional use of the leaves of the plant for the treatment of malaria.

  6. Glazed Concrete

    DEFF Research Database (Denmark)

    Bache, Anja Margrethe

    2010-01-01

    Why glazed concrete? Concrete hardens and finds its strength at room temperature whereas clay products must first be fired before they achieve this strength. They are stronger and three times as durable as clay products, which is a weighty reason for choosing concrete.5 Another reason, which....... If this succeeds, it will be possible to manufacture thin, large-scale glazed concrete panels comparable in size to concrete sandwich construction and larger which, with or without back-casting, can work as load-bearing construction elements....

  7. Properties of concretes produced with waste concrete aggregate

    International Nuclear Information System (INIS)

    Topcu, Ilker Bekir; Sengel, Selim

    2004-01-01

    An environmentally friendly approach to the disposal of waste materials, a difficult issue to cope with in today's world, would only be possible through a useful recycling process. For this reason, we suggest that clearing the debris from destroyed buildings in such a way as to obtain waste concrete aggregates (WCA) to be reused in concrete production could well be a partial solution to environmental pollution. For this study, the physical and mechanical properties along with their freeze-thaw durability of concrete produced with WCAs were investigated and test results presented. While experimenting with fresh and hardened concrete, mixtures containing recycled concrete aggregates in amounts of 30%, 50%, 70%, and 100% were prepared. Afterward, these mixtures underwent freeze-thaw cycles. As a result, we found out that C16-quality concrete could be produced using less then 30% C14-quality WCA. Moreover, it was observed that the unit weight, workability, and durability of the concretes produced through WCA decreased in inverse proportion to their endurance for freeze-thaw cycle

  8. Influence of vertical holes on creep and shrinkage of railway prestressed concrete sleepers

    Science.gov (United States)

    Li, Dan; Ngamkhanong, Chayut; Kaewunruen, Sakdirat

    2017-09-01

    Railway prestressed concrete sleepers (or railroad ties) must successfully perform two critical duties: first, to carry wheel loads from the rails to the ground; and second, to secure rail gauge for dynamic safe movements of trains. The second duty is often fouled by inappropriate design of the time-dependent behaviors due to their creep, shrinkage and elastic shortening responses of the materials. In addition, the concrete sleepers are often modified on construction sites to fit in other systems such as cables, signalling gears, drainage pipes, etc. Accordingly, this study is the world first to investigate creep and shrinkage effects on the railway prestressed concrete sleepers with vertical holes. This paper will highlight constitutive models of concrete materials within the railway sleepers under different environmental conditions over time. It will present a comparative investigation using a variety of methods to evaluate shortening effects in railway prestressed concrete sleepers. The outcome of this study will improve material design, which is very critical to the durability of railway track components.

  9. A latex metabolite benefits plant fitness under root herbivore attack

    OpenAIRE

    Huber, M.; Epping, J.; Gronover, C.S.; Fricke, J.; Aziz, Z.; Brillatz, T.; Swyers, M.; Köllner, T.G.; Vogel, H.; Hammerbacher, A.; Triebwasser-Freese, D.; Robert, C.A.M.; Verhoeven, K.; Preite, V.; Gershenzon, J.

    2016-01-01

    Plants produce large amounts of secondary metabolites in their shoots and roots and store them in specialized secretory structures. Although secondary metabolites and their secretory structures are commonly assumed to have a defensive function, evidence that they benefit plant fitness under herbivore attack is scarce, especially below ground. Here, we tested whether latex secondary metabolites produced by the common dandelion (Taraxacum officinale agg.) decrease the performance of its major n...

  10. Concrete Hinges

    DEFF Research Database (Denmark)

    Halding, Philip Skov; Hertz, Kristian Dahl; Schmidt, Jacob Wittrup

    2014-01-01

    In the first part of the 20th century concrete hinges developed by Freyssinet and Mesnager were widely tested and implemented in concrete structures. The concrete hinges were used a great deal in closed-spandrel arch bridges. Since such a bridge type has not been competitive for the past 40 years......, the research in concrete hinges has not evolved significantly in that period. But introducing a new state-of-the-art concrete arch bridge solution (Pearl-Chain arches invented at the Technical University of Denmark) creates a necessity of a concrete hinge research based on modern standards. Back when research...... in concrete hinges was more common different designs were proposed for the geometry and reinforcement. Previous research focused on fatigue, multi-axial stresses around the hinge throat, and the relation between rotation- and moment. But many different test-setups were proposed by different researchers...

  11. Use of a latex biomembrane for bladder augmentation in a rabbit model: biocompatibility, clinical and histological outcomes

    Directory of Open Access Journals (Sweden)

    Andre L. A. Domingos

    2009-04-01

    Full Text Available PURPOSE: To investigate histological features and biocompatibility of a latex biomembrane for bladder augmentation using a rabbit model. MATERIAL AND METHODS: After a partial cystectomy, a patch of a non-vulcanized latex biomembrane (2x4 cm was sewn to the bladder with 5/0 monofilament polydioxanone sulfate in a watertight manner. Groups of 5 animals were sacrificed at 15, 45 and 90 days after surgery and the bladder was removed. The 5-µm preparations obtained from grafted area and normal bladder were stained with hematoxylin-eosin. Immunohistochemical staining was performed with a primary antibody against alpha-actin to assess muscle regeneration. RESULTS: No death, urinary leakage or graft extrusion occurred in any group. All bladders showed a spherical shape. Macroscopically, after 90 days, the latex biomembrane was not identifiable and the patch was indistinguishable from normal bladder. A bladder stone was found in one animal (6.6%. On the 90th day, histology revealed continuity of transitional epithelium of host bladder tissue on the patch area. At this time, the muscle layers were well organized in a similar fashion to native bladder muscle layers. The inflammatory process was higher on grafted areas when compared to controls: 15 days - p < 0.0001, 45 days - p < 0.001, and 90 days - p < 0.01. The anti alpha-actin immunoexpression peaked at 45 days, when the graft was observed covered by muscle cells. CONCLUSION: The latex biomembrane is biocompatible and can be used in models for bladder augmentation in rabbits. It promotes epithelium and muscle regeneration without urinary leakage.

  12. Irradiation grafting of natural rubber latex with maleic anhydride and its compatibilization of poly(lactic acid)/natural rubber blends

    Science.gov (United States)

    Pongsathit, Siriwan; Pattamaprom, Cattaleeya

    2018-03-01

    Maleic anhydride (MA) is an interesting monomer to be grafted onto natural rubber(NR) due to its potential as a compatibilizer of hydrophobic rubbers and polymers with higher polarity. So far, radiation grafting of MA onto NR in latex state has not been reported. In this study, the grafting of NR with MA in latex state was investigated by exposing the latex to cobalt-60 gamma irradiation at a fixed MA content of 9% and a varied absorbed doses from 2 to 10 kGy. The FTIR spectrometer, 1H NMR spectrometer and gel content analysis have confirmed successful grafting of MA onto NR after irradiation. The grafted NRs were then used to increase the compatibility and the impact property of PLA/NR blends. It was found that the highest impact strength of the blends was achieved when the grafting was carried out at the absorbed dose of 4 kGy.

  13. Constitutive Behavior of Reinforced Concrete Membrane Elements under Tri-directional Shear

    Science.gov (United States)

    Labib, Moheb

    The two-dimensional behavior of typical reinforced concrete (RC) structures has been extensively studied in the past several decades by investigating the constitutive behavior of full-scale reinforced concrete elements subjected to a bi-axial state of stress. In order to understand the true behavior of many large complex structures, the goal of this investigation is to develop new constitutive relationships for RC elements subjected to tri-directional shear stresses. Recently, additional out-of-plane jacks were installed on the panel tester at University of Houston so that concrete elements could be subjected to tri-directional shear stresses. This upgrade makes the panel tester the only one of its kind in the US that is capable of applying such combinations of stresses on full-scale reinforced concrete elements. This dissertation presents the details of the mounting and installation of the additional hydraulic jacks on the universal panel tester. The experimental program includes a series of seven reinforced concrete elements subjected to different combinations of in-plane and out-of-plane shear stresses. Increasing the applied out-of-plane shear stresses reduced the membrane shear strength of the elements. The effect of applying out-of-plane shear stresses on the in-plane shear strength was represented by modifying the softening coefficient in the compression stress strain curve of concrete struts. The modified model was able to capture the behavior and the ultimate capacity of the tested elements. The effect of the in-plane shear reinforcement ratio on the interaction between in-plane and out-of-plane shear stresses was evaluated. The model was implemented in the Finite Element package FEAP and was used to predict the ultimate capacity of many structures subjected to a combination of in-plane and out-of-plane shear stresses. The results of the analytical model were used to develop simplified design equations for members subjected to bi-directional shear loads

  14. Significance of tests and properties of concrete and concrete-making materials

    CERN Document Server

    Pielert, James H

    2006-01-01

    Reflects a decade of technological changes in concrete industry! The newest edition of this popular ASTM publication reflects the latest technology in concrete and concrete-making materials. Six sections cover: (1) General information on the nature of concrete, sampling, variability, and testing laboratories. A new chapter deals with modeling cement and concrete properties. (2) Properties of freshly mixed concrete. (3) Properties of hardened concrete. (4) Concrete aggregates—this section has been revised and the chapters are presented in the order that most concerns concrete users: grading, density, soundness, degradation resistance, petrographic examination, reactivity, and thermal properties. (5) Materials other than aggregates—the chapter on curing materials now reflects the current technology of materials applied to new concrete surfaces. The chapter on mineral admixtures has been separated into two chapters: supplementary cementitious materials and ground slag. (6) Specialized concretes—contains a ...

  15. The word concreteness effect occurs for positive, but not negative, emotion words in immediate serial recall.

    Science.gov (United States)

    Tse, Chi-Shing; Altarriba, Jeanette

    2009-02-01

    The present study examined the roles of word concreteness and word valence in the immediate serial recall task. Emotion words (e.g. happy) were used to investigate these effects. Participants completed study-test trials with seven-item study lists consisting of positive or negative words with either high or low concreteness (Experiments 1 and 2) and neutral (i.e. non-emotion) words with either high or low concreteness (Experiment 2). For neutral words, the typical word concreteness effect (concrete words are better recalled than abstract words) was replicated. For emotion words, the effect occurred for positive words, but not for negative words. While the word concreteness effect was stronger for neutral words than for negative words, it was not different for the neutral words and the positive words. We conclude that both word valence and word concreteness simultaneously contribute to the item and order retention of emotion words and discuss how Hulme et al.'s (1997) item redintegration account can be modified to explain these findings.

  16. Design of ultra-lightweight concrete: towards monolithic concrete structures

    Directory of Open Access Journals (Sweden)

    Yu Qing Liang

    2014-04-01

    Full Text Available This study addresses the development of ultra-lightweight concrete. A moderate strength and an excellent thermal conductivity of the lightweight concrete are set as the design targets. The designed lightweight aggregates concrete is targeted to be used in monolithic concrete façade structure, performing as both load bearing element and thermal insulator. The developed lightweight concrete shows excellent thermal properties, with a low thermal conductivity of about 0.12 W/(m·K; and moderate mechanical properties, with 28-day compressive strengths of about 10-12 N/mm . This combination of values exceeds, to the researchers’ knowledge, the performance of all other lightweight building materials. Furthermore, the developed lightweight concrete possesses excellent durability properties.

  17. Improving rubber concrete by waste organic sulfur compounds.

    Science.gov (United States)

    Chou, Liang-Hisng; Lin, Chun-Nan; Lu, Chun-Ku; Lee, Cheng-Haw; Lee, Maw-Tien

    2010-01-01

    In this study, the use of crumb tyres as additives to concrete was investigated. For some time, researchers have been studying the physical properties of concrete to determine why the inclusion of rubber particles causes the concrete to degrade. Several methods have been developed to improve the bonding between rubber particles and cement hydration products (C-S-H) with the hope of creating a product with an improvement in mechanical strength. In this study, the crumb tyres were treated with waste organic sulfur compounds from a petroleum refining factory in order to modify their surface properties. Organic sulfur compounds with amphiphilic properties can enhance the hydrophilic properties of the rubber and increase the intermolecular interaction forces between rubber and C-S-H. In the present study, a colloid probe of C-S-H was prepared to measure these intermolecular interaction forces by utilizing an atomic force microscope. Experimental results showed that rubber particles treated with waste organic sulfur compounds became more hydrophilic. In addition, the intermolecular interaction forces increased with the adsorption of waste organic sulfur compounds on the surface of the rubber particles. The compressive, tensile and flexural strengths of concrete samples that included rubber particles treated with organic sulfur compound also increased significantly.

  18. SUSTAINABLE CONCRETE FOR WIND TURBINE FOUNDATIONS.

    Energy Technology Data Exchange (ETDEWEB)

    BERNDT,M.L.

    2004-06-01

    % by volume steel fibers. The use of recycled concrete aggregate in the conventional and 50% slag mixes was also studied. Properties investigated included compressive and tensile strengths, elastic modulus, coefficient of permeability, thermal conductivity and durability in seawater and sulfate solutions. It was determined that the mixes containing 50% slag gave the best overall performance. Slag was particularly beneficial for concrete that used recycled aggregate and could reduce strength losses. Initial durability results indicated that corrosion of fibers in the different concrete mixes when exposed to seawater was minimal. Future research needs to include more detailed studies of mix design and properties of concrete for wind turbine foundations. Emphasis on slag-modified mixes with natural and recycled concrete aggregate is recommended. The proportion of slag that can be incorporated in the concrete needs to be optimized, as does the grading of recycled aggregate. The potential for using silica fume in conjunction with slag is worth exploring as this may further enhance strength and durability. Longer-term durability studies are necessary and other pertinent properties of concrete that require investigation include damping characteristics, pullout strength, fatigue strength and risk of thermal cracking. The properties of sustainable concrete mixes need to be integrated with studies on the structural behavior of wind turbine foundations in order to determine the optimal mix design and to examine means of reducing conservatism and cost of foundations.

  19. Concrete structures

    CERN Document Server

    Setareh, Mehdi

    2017-01-01

    This revised, fully updated second edition covers the analysis, design, and construction of reinforced concrete structures from a real-world perspective. It examines different reinforced concrete elements such as slabs, beams, columns, foundations, basement and retaining walls and pre-stressed concrete incorporating the most up-to-date edition of the American Concrete Institute Code (ACI 318-14) requirements for the design of concrete structures. It includes a chapter on metric system in reinforced concrete design and construction. A new chapter on the design of formworks has been added which is of great value to students in the construction engineering programs along with practicing engineers and architects. This second edition also includes a new appendix with color images illustrating various concrete construction practices, and well-designed buildings. The ACI 318-14 constitutes the most extensive reorganization of the code in the past 40 years. References to the various sections of the ACI 318-14 are pro...

  20. Promoting the use of crumb rubber concrete in developing countries.

    Science.gov (United States)

    Batayneh, Malek K; Marie, Iqbal; Asi, Ibrahim

    2008-11-01

    The use of accumulated waste materials in third world countries is still in its early phases. It will take courage for contractors and others in the construction industry to recycle selected types of waste materials in the concrete mixes. This paper addresses the recycling of rubber tires accumulated every year in Jordan to be used in concrete mixes. The main objectives of this research were to provide more scientific evidence to support the use of legislation or incentive-based schemes to promote the reuse of accumulated waste tires. This research focused on using crumb tires as a replacement for a percentage of the local fine aggregates used in the concrete mixes in Jordan. Different concrete specimens were prepared and tested in terms of uniaxial compression and splitting tension. The main variable in the mixture was the volumetric percentage of crumb tires used in the mix. The test results showed that even though the compressive strength is reduced when using the crumb tires, it can meet the strength requirements of light weight concrete. In addition, test results and observations indicated that the addition of crumb rubber to the mix has a limited effect toward reducing the workability of the mixtures. The mechanical test results demonstrated that the tested specimens of the crumb rubber concrete remained relatively intact after failure compared to the conventional concrete specimens. It is also concluded that modified concrete would contribute to the disposal of the non-decaying scrap tires, since the amount being accumulated in third world countries is creating a challenge for proper disposal. Thus, obliging authorities to invest in facilitating the use of waste tires in concrete, a fundamental material to the booming construction industry in theses countries, serves two purposes.

  1. Thermoresponsive latexes for fragrance encapsulation and release.

    Science.gov (United States)

    Popadyuk, N; Popadyuk, A; Kohut, A; Voronov, A

    2016-04-01

    To synthesize cross-linked latex particles protecting the encapsulated fragrance at ambient temperatures and facilitating the release of cargo at the temperature of the surface of the skin that varies in different regions of the body between 33.5 and 36.9°C. Poly(stearyl acrylate) (PSA), a polymer with long crystallizable alkyl side chains (undergoes order-disorder transitions at 45°C), was chosen as the main component of the polymer particles. As a result, new thermoresponsive polymer particles for fragrance encapsulation were synthesized and characterized, including assessing the performance of particles in triggered release by elevated temperature. To obtain network domains of various crystallinity, stearyl acrylate was copolymerized with dipropylene glycol acrylate caprylate (DGAC) (comonomer) in the presence of a dipropylene glycol diacrylate sebacate (cross-linker) using the miniemulsion process. Comonomers and a cross-linker were mixed directly in a fragrance during polymerization. Fragrance release was evaluated at 25, 31, 35 and 39°C to demonstrate a new material potential in personal/health care skin-related applications. Particles protect the fragrance from evaporation at 25°C. The fragrance release rate gradually increases at 31, 35 and 39°C. Two slopes were found on release plots. The first slope corresponds to a rapid fragrance release. The second slope indicates a subsequent reduction in the release rate. Crystalline-to-amorphous transition of PSA triggers the release of fragrances from cross-linked latex particles at elevated temperatures. The presence of the encapsulated fragrance, as well as the inclusion of amorphous fragments in the polymer network, reduces the particle crystallinity and enhances the release. Release profiles can be tuned by temperature and controlled by the amount of loaded fragrance and the ratio of comonomers in the feed mixture. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  2. Proportioning and performance evaluation of self-consolidating concrete

    Science.gov (United States)

    Wang, Xuhao

    A well-proportioned self-consolidating concrete (SCC) mixture can be achieved by controlling the aggregate system, paste quality, and paste quantity. The work presented in this dissertation involves an effort to study and improve particle packing of the concrete system and reduce the paste quantity while maintaining concrete quality and performance. This dissertation is composed of four papers resulting from the study: (1) Assessing Particle Packing Based Self-Consolidating Concrete Mix Design; (2) Using Paste-To-Voids Volume Ratio to Evaluate the Performance of Self-Consolidating Concrete Mixtures; (3) Image Analysis Applications on Assessing Static Stability and Flowability of Self-Consolidating Concrete, and (4) Using Ultrasonic Wave Propagation to Monitor Stiffening Process of Self-Consolidating Concrete. Tests were conducted on a large matrix of SCC mixtures that were designed for cast-in-place bridge construction. The mixtures were made with different aggregate types, sizes, and different cementitious materials. In Paper 1, a modified particle-packing based mix design method, originally proposed by Brouwers (2005), was applied to the design of self-consolidating concrete (SCC) mixs. Using this method, a large matrix of SCC mixes was designed to have a particle distribution modulus (q) ranging from 0.23 to 0.29. Fresh properties (such as flowability, passing ability, segregation resistance, yield stress, viscosity, set time and formwork pressure) and hardened properties (such as compressive strength, surface resistance, shrinkage, and air structure) of these concrete mixes were experimentally evaluated. In Paper 2, a concept that is based on paste-to-voids volume ratio (Vpaste/Vvoids) was employed to assess the performance of SCC mixtures. The relationship between excess paste theory and Vpaste/Vvoids was investigated. The workability, flow properties, compressive strength, shrinkage, and surface resistivity of SCC mixtures were determined at various ages

  3. Study of the performance of four repairing material systems for hydraulic structures of concrete dams

    Directory of Open Access Journals (Sweden)

    Kormann A. C. M.

    2003-01-01

    Full Text Available Four types of repairing materials are studied as function of either a conventional concrete or a reference-concrete (RefC, these are: polymer-modified cement mortar (PMor, steel fiber concrete (SFco, epoxy mortar (EMor and silica fume mortar (SFmo, to be applied in hydraulic structures surfaces subjected to a high velocity water flow. Besides the mechanical requests and wearing resistance of hydraulic concrete dam structures, especially the spillway surfaces, the high solar radiation, the environmental temperature and wet and dry cycles, contribute significantly to the reduction of their lifespan. RefC and the SFco were developed based on a usual concrete mixture used in slabs of spillways. The average RefC mixture used was 1: 1.61: 2.99: 0.376, with Pozzolan-modified Portland cement consumption of 425 kg/m³. EMor and PMor mixtures followed the information given by the manufacturers and lab experience. Tests on concrete samples were carried out in laboratory simulating normally found environmental situations in order to control the mechanical resistance and the aging imposed conditions, such as solar radiation and humidity. Also, physicochemical characterizing tests were made for all used materials. From the analyzed results, two of them presented a higher performance: the EMor and SFmo. SFco presented good adherence to the RefC and good mechanical performance. However, it also presented apparent metal corrosion in humidity tests, being indicated for use, with caution, as an intermediate layer in underwater repairs. In a general classification, considering all tests, including their field applications, the better performance material systems were EMor- SFmo> SFco> PMor.

  4. n-BA/KOH/t-BHP behaviour in the natural rubber latex vulcanization by gamma rays

    International Nuclear Information System (INIS)

    Souza, A. de.

    1994-01-01

    Natural rubber latex was vulcanized in the absence and in the presence of sensitizer (S), with gamma ray from 60 Co source, panoramic type, at the dose rate range of 1,20-1,33 kGy/h. The components of used S were n-butyl acrylate (n-BA), the KOH as stabilizer and t-butyl hydroperoxide (t-BHP) as co-S. The purpose of this work was to study the efficiency and the behaviour of each component of S in the irradiated latex crosslinking by tensile strength (T b ), volume fraction and permanent set. In the absence of S occur straight crosslinking between macromolecular adjacent radicals. IN the presence of S, the n-BA participates in the crosslinking through acrylic bridges between macromolecules. (author)

  5. Latex paint as a delivery vehicle for diethylphthalate and di-n-butylphthalate

    DEFF Research Database (Denmark)

    Schripp, Tobias; Salthammer, Tunga; Fauck, Christian

    2014-01-01

    gas-phase concentration at steady state(y). For both, DEP and DnBP, the y0 obtained was lower than the respective saturation vapor pressure (Ps). Furthermore, for both phthalates in latex paint, the material/air partition coefficient (C0/y0) was close in value to the octanol/air partition coefficient...

  6. Fibre Concrete 2017

    Science.gov (United States)

    2017-09-01

    9th international conference on fibre reinforced concretes (FRC), textile reinforced concretes (TRC) and ultra-high performance concretes (UHPC) Preface The Fibre Concrete Conference series is held biennially to provide a platform to share knowledge on fibre reinforced concretes, textile concretes and ultra-high performance concretes regarding material properties and behaviour, technology procedures, topics of long-term behaviour, creep, durability; sustainable aspects of concrete including utilisation of waste materials in concrete production and recycling of concrete. The tradition of Fibre Concrete Conferences started in eighties of the last century. Nowadays the conference is organized by the Department of Concrete and Masonry Structures of the Czech Technical University in Prague, Faculty of Civil Engineering. The 9th International Conference Fibre Concrete 2017 had 109 participants from 27 countries all over the world. 55 papers were presented including keynote lectures of Professor Bažant, Professor Bartoš and Dr. Broukalová. The conference program covered wide range of topics from scientific research to practical applications. The presented contributions related to performance and behaviour of cement based composites, their long-term behaviour and durability, sustainable aspects, advanced analyses of structures from these composites and successful applications. This conference was organized also to honour Professor Zděnek P. Bažant on the occasion of his jubilee and to appreciate his merits and discoveries in the field of fibre reinforced composites, structural mechanics and engineering.

  7. Transport of accelerator produced high energy neutrons though concrete

    International Nuclear Information System (INIS)

    Prabhakar Rao, G.; Sarkar, P.K.

    1996-01-01

    Development of a computational system for estimating the production and transport of high energy neutrons in particle accelerators is reported. The energy-angle distribution of neutrons from accelerated ions bombarding thick targets is calculated by a hybrid nuclear reaction model code, ALICE-91, modified to suit the purpose. Subsequent transmission of these neutrons through concrete slabs is treated using the anisotropic source-flux iteration technique (ASFIT) in the framework of a coupled neutron-gamma transport. Several parameters of both the codes have been optimized to obtain the transmitted dose through concrete. The calculations are found to be accurate and at the same time faster compared to the detailed Monte Carlo calculations. (author). 8 refs., 2 figs

  8. LIGHTWEIGHT CONCRETES WITH FLY–ASH OF PRYDNIPROVSK THERMAL POWER STATION

    Directory of Open Access Journals (Sweden)

    M. I. Netesa

    2013-08-01

    Full Text Available Purpose. Determination of conformities to law of influence of expense of components of easy concretes, which turn out on the basis of local afterproducts of industry, on their basic properties under conditions of enhanceable efficiency of the use of cement. Methodology. Experimental studies on optimization of structures and properties of concrete were carried out with use of mathematical planning experiments methods. All experiments were carried out on orthogonal design with three variables. Cement, water and additives PLKP-2 consumption were taken as varied factors. Findings. Vast experimental studies on determination of rational compositions of concrete mixtures were conducted with the use as fillers of granulated slag from iron and steel plant named after Petrovskiy and Dnepr sand, as binding agent Krivoy Rog portland-cement II/B-Ш-400, as filler fly-ash of Pridneprovsk Thermal Power Station. Efficiency coefficient of cement use was adopted as basic criterion of concrete composition rationality, it is determined on the relation of the attained durability per unit weight of used cement. For greater efficiency coefficient of cement use regularity of rational grain composition of components previously obtained was adopted, it is provided at a ratio of a large fraction consumption to medium and small 52:23:25, and their sizes are approximately 100:10:1. Experimental studies with use of mathematical planning experiments method were carried out. By results of their processing isofields were constructed according to the strength and effectiveness of the use of cement ratio of the studied factors. Originality. By strength comparative tests of hardened concrete with various local secondary resources, modified with complex plasticizer PLKP-2 additive, it was found that lightweight concrete with the density of 1700…1800 kg/m3 and concrete compressive strength from 5 to 20 MPa on the basis of granulated slag from the iron and steel plant named after

  9. Concrete laying laboratory

    International Nuclear Information System (INIS)

    Bastlova, K.

    1986-01-01

    The task of the concrete laying laboratory established within a special department for quality control and assurance at the Dukovany nuclear power plant, is to check the composition of concrete mixes produced by the central concrete production plant on the site, and the shipment, laying and processing of concrete. The composition is given of special barite and serpentinite concretes designed for biological shields. The system of checks and of filing the results is briefly described. Esperience is summed up from the operation of the concrete laying laboratory, and conclusions are formulated which should be observed on similar large construction sites. They include the precise definition of the designer's requirements for the quality of concrete, the surface finish of concrete surfaces, the method of concreting specific structures around bushings, increased density reinforcements and various technological elements, and requirements for shipment to poorly accessible or remote places. As for the equipment of the laboratory, it should be completed with an instrument for the analysis of fresh concrete mixes, a large capacity drying kiln, etc. (Z.M.)

  10. Concrete with onyx waste aggregate as aesthetically valued structural concrete

    Science.gov (United States)

    Setyowati E., W.; Soehardjono, A.; Wisnumurti

    2017-09-01

    The utillization of Tulungagung onyx stone waste as an aggregate of concrete mixture will improve the economic value of the concrete due to the brighter color and high aesthetic level of the products. We conducted the research of 75 samples as a test objects to measure the compression stress, splits tensile stress, flexural tensile stress, elasticity modulus, porosity modulus and also studied 15 test objects to identify the concrete micro structures using XRD test, EDAX test and SEM test. The test objects were made from mix designed concrete, having ratio cement : fine aggregate : coarse aggregate ratio = 1 : 1.5 : 2.1, and W/C ratio = 0.4. The 28 days examination results showed that the micro structure of Tulungagung onyx waste concrete is similar with normal concrete. Moreover, the mechanical test results proved that Tulungagung onyx waste concretes also have a qualified level of strength to be used as a structural concrete with higher aesthetic level.

  11. Latex particle template lift-up guided gold wire-networks via evaporation lithography

    KAUST Repository

    Lone, Saifullah; Vakarelski, Ivan Uriev; Chew, Basil; Wang, Zhihong; Thoroddsen, Sigurdur T

    2014-01-01

    We describe a hybrid methodology that combines a two dimensional (2D) monolayer of latex particles (with a pitch size down to 1 μm) prepared by horizontal dry deposition, lift-up of a 2D template onto flat surfaces and evaporation lithography to fabricate metal micro- and nano wire-networks. This journal is

  12. Influence of DAD-TA temperature-reducing additive on physical and mechanical properties of bitumen and compaction of asphalt concrete.

    Science.gov (United States)

    Yadykina, V. V.; Akimov, A. E.; Trautvain, A. I.; Kholopov, V. S.

    2018-03-01

    The paper is devoted to the use of DAD-TA temperature-reducing additive for the preparation and pouring of asphalt concrete mixes at reduced temperatures. It also shows positive influence of the modified bitumen on the efficiency of organo-mineral composite compaction at reduced temperatures. Physical and mechanical properties of asphalt concrete with the use of bitumen modified by DAD-TA additive including indicators characterizing road surfacing life are presented. Arguments to use this material from the point of view of its production technology and environmental impact are given.

  13. Preservation of H2 production activity in nanoporous latex coatings of Rhodopseudomonas palustris CGA009 during dry storage at ambient temperatures: Preservation of R. palustris latex coatings

    Energy Technology Data Exchange (ETDEWEB)

    Piskorska, M. [Univ. of South Carolina, Aiken, SC (United States); Soule, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Gosse, J. L. [North Carolina State Univ., Raleigh, NC (United States); Milliken, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Flickinger, M. C. [North Carolina State Univ., Raleigh, NC (United States); Smith, G. W. [Univ. of South Carolina, Aiken, SC (United States); Yeager, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-01-21

    To assess the applicability of latex cell coatings as an ‘off-the-shelf’ biocatalyst, the effect of osmoprotectants, temperature, humidity and O2 on preservation of H2 production in Rhodopseudomonas palustris coatings was evaluated. Immediately following latex coating coalescence (24 h) and for up to 2 weeks of dry storage, rehydrated coatings containing different osmoprotectants displayed similar rates of H2 production. Beyond 2 weeks of storage, sorbitol-treated coatings lost all H2 production activity, whereas considerable H2 production was still detected in sucrose- and trehalose-stabilized coatings. The relative humidity level at which the coatings were stored had a significant impact on the recovery and subsequent rates of H2 production. After 4 weeks storage under air at 60% humidity, coatings produced only trace amounts of H2 (0–0.1% headspace accumulation), whereas those stored at < 5% humidity retained 27–53% of their H2 production activity after 8 weeks of storage. In conWhen stored in argon at < 5% humidity and room temperature, R. palustris coatings retained full H2 production activity for 3 months, implicating oxidative damage as a key factor limiting coating storage. Overall, the results demonstrate that biocatalytic latex coatings are an attractive cell immobilization platform for preservation of bioactivity in the dry state.

  14. Crystallization of Hevamine, an Enzyme with Lysozyme/Chitinase Activity from Hevea brasiliensis Latex

    NARCIS (Netherlands)

    ROZEBOOM, HJ; BUDIANI, A; BEINTEMA, JJ

    1990-01-01

    Hevamine, an enzyme with both lysozyme and chitinase activity, was isolated and purified from Hevea brasiliensis (rubber tree) latex. The enzyme (molecular weight 29,000) is homologous to certain “pathogenesis-related” proteins from plants, but not to hen egg-white or phage T4 lysozyme. To

  15. Enhancing Student Writing and Computer Programming with LATEX and MATLAB in Multivariable Calculus

    Science.gov (United States)

    Sullivan, Eric; Melvin, Timothy

    2016-01-01

    Written communication and computer programming are foundational components of an undergraduate degree in the mathematical sciences. All lower-division mathematics courses at our institution are paired with computer-based writing, coding, and problem-solving activities. In multivariable calculus we utilize MATLAB and LATEX to have students explore…

  16. Pervious Concrete

    OpenAIRE

    Torsvik, Øyvind André Hoff

    2012-01-01

    Pervious concrete is a material with a high degree of permeability but generally low strength. The material is primarily used for paving applications but has shown promise in many other areas of usage. This thesis investigates the properties of pervious concrete using normal Norwegian aggregates and practices. An overview of important factors when it comes to designing and producing pervious concrete is the result of this investigation. Several experiments have been performed in the concrete ...

  17. Natural asphalt modified binders used for high stiffness modulus asphalt concrete

    Science.gov (United States)

    Bilski, Marcin; Słowik, Mieczysław

    2018-05-01

    This paper presents a set of test results supporting the possibility of replacing, in Polish climate conditions, hard road 20/30 penetration grade bitumen used in the binder course and/or base course made of high stiffness modulus asphalt concrete with binders comprising of 35/50 or 50/70 penetration grade bitumens and additives in the form of natural Gilsonite or Trinidad Epuré asphalts. For the purpose of comparing the properties of the discussed asphalt binders, values of the Performance Grade have been determined according to the American Superpave system criteria.

  18. Sustainable Concrete Technology

    Directory of Open Access Journals (Sweden)

    Sim J.

    2015-12-01

    Full Text Available The growing concern over global warming and significant ecological changes requires sustainable development in all fields of science and technology. Concrete not only consumes huge amount of energy and natural sources, but also emits large amount of CO2, mainly due to the production of cement. It is evident that such large amount of concrete production has put significant impact on the energy, resource, environment, and ecology of the society. Hence, how to develop the concrete technology in a sustainable way has become a significant issue. In this paper, some of Korean researches for sustainable development of concrete are presented. These are sustainable strengthening for deteriorated concrete structure, sustainable reinforcement of new concrete structure, sustainable concrete using recycled aggregate and supplementary cementing materials and finally application of each technique to precast concrete.

  19. Influence of wearing latex gloves on electric pulp tester readings in children.

    Science.gov (United States)

    Holan, G

    1993-12-01

    Electric pulp testers operated by completing an electric circuit. Latex examination gloves have been claimed to interrupt this circuit and lead to false-negative results. This study was conducted to evaluate the influence of wearing latex gloves on electric pulp tester (EPT) readings. The pulps of 80 maxillary permanent incisors of 22 children 10-13 1/2 years old were tested using the Pelton & Crane 'Vitapulp' instrument. Each tooth was tested twice: with gloves and with bare hands. Teeth failing to respond to the EPT without gloves were excluded from the study. All EPT readings ranged between 1 and 9.5. Five teeth gave the same responses with gloved and ungloved hands. Only five teeth did not respond when gloves were worn, and all of these gave readings near the top of the EPT scale when tested without gloves. The other 70 teeth presented significantly higher readings with gloves than without gloves. It is concluded that removal of examination gloves during the operation of the EPT is necessary only if no response is obtained.

  20. Properties of concrete containing foamed concrete block waste as fine aggregate replacement

    Science.gov (United States)

    Muthusamy, K.; Budiea, A. M. A.; Zaidan, A. L. F.; Rasid, M. H.; Hazimmah, D. S.

    2017-11-01

    Environmental degradation due to excessive sand mining dumping at certain places and disposal of foamed concrete block waste from lightweight concrete producing industry are issues that should be resolved for a better and cleaner environment of the community. Thus, the main intention of this study is to investigate the potential of foamed concrete block waste as partial sand replacement in concrete production. The foamed concrete waste (FCW) used in this research that were supplied by a local lightweight concrete producing industry. The workability and compressive strength of concrete containing various percentage of foamed concrete waste as partial sand replacement has been investigated. Prior to the use, the foamed concrete waste were crushed to produce finer particles. Six concrete mixes containing various content of crushed foamed concrete waste that are 0%, 10%, 20%, 30%, 40% and 50% were used in this experimental work. Then the prepared specimens were placed in water curing until the testing age. Compressive strength test and flexural strength tests were conducted at 7, 14 and 28 days. The result shows that integration of crushed foamed concrete waste as partial sand replacement in concrete reduces the mix workability. It is interesting to note that both compressive strength and flexural strength of concrete improves when 30% crushed foamed concrete waste is added as partial sand replacement.