WorldWideScience

Sample records for large-actuator-number horizontal path

  1. 45 Km Horizontal Path Optical Link Experiment

    Science.gov (United States)

    Biswas, A.; Ceniceros, J.; Novak, M.; Jeganathan, M.; Portillo, A.; Erickson, D.; Depew, J.; Sanii, B.; Lesh, J. R.

    2000-01-01

    Mountain-top to mountain-top optical link experiments have been initiated at JPL, in order to perform a systems level evaluation of optical communications. Progress made so far is reported. ne NASA, JPL developed optical communications demonstrator (OCD) is used to transmit a laser signal from Strawberry Peak (SP), located in the San Bernadino mountains of California. This laser beam is received by a 0.6 m aperture telescope at JPL's Table Mountain Facility (TMF), located in Wrightwood, California. The optical link is bi-directional with the TMF telescope transmitting a continuous 4-wave (cw) 780 run beacon and the OCD sending back a 840 nm, 100 - 500 Mbps pseudo noise (PN) modulated, laser beam. The optical link path is at an average altitude of 2 km above sea level, covers a range of 46.8 km and provides an atmospheric channel equivalent to approx. 4 air masses. Average received power measured at either end fall well within the uncertainties predicted by link analysis. The reduction in normalized intensity variance (sigma(sup 2, sub I)) for the 4-beam beacon, compared to each individual beam, at SP, was from approx. 0.68 to 0.22. With some allowance for intra-beam mis-alignment, this is consistent with incoherent averaging. The sigma(sup2, sub I) measured at TMF approx. 0.43 +/- 0.22 exceeded the expected aperture averaged value of less than 0.1, probably because of beam wander. The focused spot sizes of approx. 162 +/- 6 microns at the TMF Coude and approx. 64 +/- 3 microns on the OCD compare to the predicted size range of 52 - 172 microns and 57 - 93 microns, respectively. This is consistent with 4 - 5 arcsec of atmospheric "seeing". The preliminary evaluation of OCD's fine tracking indicates that the uncompensated tracking error is approx. 3.3 micro rad compared to approx. 1.7 micro rad observed in the laboratory. Fine tracking performance was intermittent, primarily due to beacon fades on the OCD tracking sensor. The best bit error rates observed while

  2. Horizontal routes: current paths of literary criticism in Latin America

    Directory of Open Access Journals (Sweden)

    Ariadne Costa da Mata

    2013-07-01

    Full Text Available In the last decades, the tendency towards horizontality became visible, particularly (but not only in social movements. Horizontality implies a new architecture in human organizations and pushes for changes in the way knowledge is produced and organized. More than a simple erosion of frontiers between fields, horizontality means the decentralization and dissemination of power.

  3. Angular anisoplanatism of a focused beam using beacons over horizontal path

    Science.gov (United States)

    Wu, Wu-ming; Ning, Yu

    2016-01-01

    The performance of the achieve laser beam propagation through atmospheric turbulence with adaptive optics is degraded by the fact that the wavefront aberrations difference. This error is only include the angular anisoplanatism when there is separation between the achieve laser beam and beacon. In the paper we derive an analytic expression for the effective angular anisoplanatism as a function of displacement angular when the turbulence profile is uniform. It shows that the effective angular anisoplanatism becomes weaker as the diameter of laser beams and the Fried transverse coherence length increase. We report results from field experiments that the effective angular anisoplanatism of a focused beam over horizontal path. It is found that measured and theoretical results are consistent. The effective wavefront variance increases with the strength of atmospheric turbulence and the angular displacement. And the constant phase of angular anisoplanatism has no effect on the Strehl ratio of the beam.

  4. Horizontal

    Institute of Scientific and Technical Information of China (English)

    ZHONG; Chunping

    2005-01-01

    [1]Wu, H., Bochner technique in differential geometry, Advance in Math. (in Chinese), 1981, 10(1): 57-76.[2]Morrow, J., Kodaira, K., Complex Manifolds, New York: Holt, Rinehart & Winston, 1971.[3]Abate, M., Aikou, T., Patrizio, G., Preface for Complex Finsler Geometry, Cont. Math., Vol. 196, Providence,RI: Amer. Math. Soc., 1996, 97-100.[4]Abate, M., Patrizio, G., Finsler Metrics-A global approach with applications to geometric function theory,Lecture Notes in Mathematics, Vol. 1591, Bedin: Springer-Verlag, 1994.[5]Antonelli, P. L., Lackey, B.(eds.), The Theory of Finslerian Laplacians and Applications, MAIA 459, Dordrecht:Kluwer Academic Publishers, 1998.[6]Bao, D., Lackey, B., A Hodge decomposition theorem for Finsler spaces, C. R. Acad. Sci. Paris, t. 323, Serie 1,1996, 51-56.[7]Munteanu, O., Weitzenbock formulas for horizontal and vertical Laplacians, Houston Journal of Mathematics,2003, 29(4): 889-900.[8]Faran, J. J., The equivalence problem for complex Finsler Hamiltonians, Cont. Math.,Vol. 196, Providence, RI:Amer. Math. Soc., 1996, 133-144.[9]Kobayashi, S., Complex Finsler vector bundles, Cont. Math., Vol. 196, Providence, RI: Amer. Math. Soc.,1996,145-153.[10]Aikou, T., On complex Finsler manifolds, Rep. Fac. Sci. Kagoshima Univ. (Math. Phys. & Chem.), 1991, 24:9-25.

  5. Cannibalism and predation as paths for horizontal passage of Wolbachia between terrestrial isopods.

    Science.gov (United States)

    Le Clec'h, Winka; Chevalier, Frédéric D; Genty, Lise; Bertaux, Joanne; Bouchon, Didier; Sicard, Mathieu

    2013-01-01

    The alpha-proteobacteria Wolbachia are the most widespread endosymbionts in arthropods and nematodes. Mainly maternally inherited, these so-called sex parasites have selected several strategies that increase their vertical dispersion in host populations. However, the lack of congruence between the Wolbachia and their host phylogenies suggests frequent horizontal transfers. One way that could be used for horizontal Wolbachia transfers between individuals is predation. The aim of this study was to test whether horizontal passage of Wolbachia is possible when an uninfected terrestrial isopod eats an infected one. After having eaten Armadillidium vulgare harbouring Wolbachia, the predator-recipients (the two woodlice A. vulgare and Porcellio dilatatus dilatatus) that were initially Wolbachia-free were tested positive for the presence of Wolbachia both by quantitative PCR and Fluorescence in situ Hybridization (FISH). Even if the titers were low compared to vertically infected individuals, this constitutes the first demonstration of Wolbachia occurrence in various organs of an initially uninfected host after eating an infected one.

  6. Horizontal coherence of low-frequency fixed-path sound in a continental shelf region with internal-wave activity.

    Science.gov (United States)

    Duda, Timothy F; Collis, Jon M; Lin, Ying-Tsong; Newhall, Arthur E; Lynch, James F; DeFerrari, Harry A

    2012-02-01

    Sound at 85 to 450 Hz propagating in approximately 80-m depth water from fixed sources to a joint horizontal/vertical line array (HLA/VLA) is analyzed. The data are from a continental shelf area east of Delaware Bay (USA) populated with tidally generated long- and short-wavelength internal waves. Sound paths are 19 km in the along-shore (along internal-wave crest) direction and 30 km in the cross-shore direction. Spatial statistics of HLA arrivals are computed as functions of beam steering angle and time. These include array gain, horizontally lagged spatial correlation function, and coherent beam power. These quantities vary widely in magnitude, and vary over a broad range of time scales. For example, correlation scale can change rapidly from forty to five wavelengths, and correlation-scale behavior is anisotropic. In addition, the vertical array can be used to predict correlation expected for adiabatic propagation with cylindrical symmetry, forming a benchmark. Observed variations are in concert with internal-wave activity. Temporal variations of three coherence measures, horizontal correlation length, array gain, and ratio of actual correlation length to predicted adiabatic-mode correlation length, are very strong, varying by almost a factor of ten as internal waves pass.

  7. Input-Feedforward Two-Path Band-Pass Delta-Sigma Modulator Based on Horizontal or Vertical Opamp Sharing Technique

    Science.gov (United States)

    Waki, Naoya; Sato, Hiroki; Hyogo, Akira; Sekine, Keitaro

    In this paper, horizontal (where an opamp is shared in two adjacent stages) and vertical (where an opamp is shared across two paths) opamp sharing techniques for a two-path band-pass (BP) ΔΣ modulator are described, and input-feedforward two-path fourth-order BP ΔΣ modulators that have only two opamps are proposed. The proposed modulators are based on the horizontal or vertical opamp sharing technique. They can be realized with both a summation circuit using a switched capacitor (SC) network and a second-order high-pass filter (HPF) with a horizontal shared opamp or a double-sampling first-order HPF with a vertical shared opamp, which are based on an SC first-order HPF with an opamp. These techniques can reduce the number of opamps with no additional component and the chip area as well as realize lower power consumption.

  8. Effects of Inboard Horizontal Field of View Display Limitations on Pilot Path Control During Total In-Flight Simulator (TIFS) Flight Test

    Science.gov (United States)

    Kramer, Lynda J.; Parrish, Russell V.; Williams, Steven P.; Lavell, Jeffrey S.

    1999-01-01

    A flight test was conducted aboard Calspan's Total In-Flight Simulator (TIFS) aircraft by researchers within the External Visibility System (XVS) element of the High-Speed Research program. The purpose was to investigate the effects of inboard horizontal field of view (FOV) display limitations on pilot path control and to learn about the TIFS capabilities and limitations for possible use in future XVS flight tests. The TIFS cockpit windows were masked to represent the front XVS display area and the High-Speed Civil Transport side windows, as viewed by the pilot. Masking limited the forward FOV to 40 deg. horizontal and 50 deg. vertical for the basic flight condition, With an increase of 10 deg. horizontal in the inboard direction for the increased FOV flight condition. Two right-hand approach tasks (base-downwind-final) with a left crosswind on final were performed by three pilots using visual flight rules at Niagara Falls Airport. Each of the two tasks had three replicates for both horizontal FOV conditions, resulting in twelve approaches per test subject. Limited objective data showed that an increase of inboard FOV had no effect (deficiences in objective data measurement capabilities were noted). However, subjective results showed that a 50 deg. FOV was preferred over the 40 deg. FOV.

  9. The impact of horizontal heterogeneities, cloud fraction, and liquid water path on warm cloud effective radii from CERES-like Aqua MODIS retrievals

    Directory of Open Access Journals (Sweden)

    D. Painemal

    2013-10-01

    Full Text Available The impact of horizontal heterogeneities, liquid water path (LWP from AMSR-E, and cloud fraction (CF on MODIS cloud effective radius (re, retrieved from the 2.1 μm (re2.1 and 3.8 μm (re3.8 channels, is investigated for warm clouds over the southeast Pacific. Values of re retrieved using the CERES algorithms are averaged at the CERES footprint resolution (∼20 km, while heterogeneities (Hσ are calculated as the ratio between the standard deviation and mean 0.64 μm reflectance. The value of re2.1 strongly depends on CF, with magnitudes up to 5 μm larger than those for overcast scenes, whereas re3.8 remains insensitive to CF. For cloudy scenes, both re2.1 and re3.8 increase with Hσ for any given AMSR-E LWP, but re2.1 changes more than for re3.8. Additionally, re3.8–re2.1 differences are positive (Hσ 45 gm−2, and negative (up to −4 μm for larger Hσ. While re3.8–re2.1 differences in homogeneous scenes are qualitatively consistent with in situ microphysical observations over the region of study, negative differences – particularly evinced in mean regional maps – are more likely to reflect the dominant bias associated with cloud heterogeneities rather than information about the cloud vertical structure. The consequences for MODIS LWP are also discussed.

  10. 2-D reconstruction of atmospheric concentration peaks from horizontal long path DOAS tomographic measurements: parametrisation and geometry within a discrete approach

    Directory of Open Access Journals (Sweden)

    A. Hartl

    2005-11-01

    Full Text Available In this study, we theoretically investigate the reconstruction of 2-D cross sections through Gaussian concentration distributions, e.g. emission plumes, from long path DOAS measurements along a limited number of light paths. This is done systematically with respect to the extension of the up to four peaks and for six different measurement setups with 2–4 telescopes and 36 light paths each. We distinguish between cases with and without additional background concentrations. Our approach parametrises the unknown distribution by local piecewise constant or linear functions on a regular grid and solves the resulting discrete, linear system by a least squares minimum norm principle. We show that the linear parametrisation not only allows better representation of the distributions in terms of discretisation errors, but also better inversion of the system. We calculate area integrals of the concentration field (i.e. total emissions rates for non-vanishing perpendicular wind speed components and show that reconstruction errors and reconstructed area integrals within the peaks for narrow distributions crucially depend on the resolution of the reconstruction grid. A recently suggested grid translation method for the piecewise constant basis functions, combining reconstructions from several shifted grids, is modified for the linear basis functions and proven to reduce overall reconstruction errors, but not the uncertainty of concentration integrals. We suggest a procedure to subtract additional background concentration fields before inversion. We find large differences in reconstruction quality between the geometries and conclude that, in general, for a constant number of light paths increasing the number of telescopes leads to better reconstruction results. It appears that geometries that give better results for negligible measurement errors and parts of the geometry that are better resolved are also less sensitive to increasing measurement errors.

  11. 2-D reconstruction of atmospheric concentration peaks from horizontal long path DOAS tomographic measurements: parametrisation and geometry within a discrete approach

    Directory of Open Access Journals (Sweden)

    A. Hartl

    2006-01-01

    Full Text Available In this study, we theoretically investigate the reconstruction of 2-D cross sections through Gaussian concentration distributions, e.g. emission plumes, from long path DOAS measurements along a limited number of light paths. This is done systematically with respect to the extension of the up to four peaks and for six different measurement setups with 2-4 telescopes and 36 light paths each. We distinguish between cases with and without additional background concentrations. Our approach parametrises the unknown distribution by local piecewise constant or linear functions on a regular grid and solves the resulting discrete, linear system by a least squares minimum norm principle. We show that the linear parametrisation not only allows better representation of the distributions in terms of discretisation errors, but also better inversion of the system. We calculate area integrals of the concentration field (i.e. total emissions rates for non-vanishing perpendicular wind speed components and show that reconstruction errors and reconstructed area integrals within the peaks for narrow distributions crucially depend on the resolution of the reconstruction grid. A recently suggested grid translation method for the piecewise constant basis functions, combining reconstructions from several shifted grids, is modified for the linear basis functions and proven to reduce overall reconstruction errors, but not the uncertainty of concentration integrals. We suggest a procedure to subtract additional background concentration fields before inversion. We find large differences in reconstruction quality between the geometries and conclude that, in general, for a constant number of light paths increasing the number of telescopes leads to better reconstruction results. It appears that geometries that give better results for negligible measurement errors and parts of the geometry that are better resolved are also less sensitive to increasing measurement errors.

  12. The effects of water in oil on the performance of a four path Chordal ultrasonic flow meter in a horizontal flow line

    Energy Technology Data Exchange (ETDEWEB)

    Cousins, T.; Augenstein, D.; Eagle, S.

    2005-07-01

    A series of flow tests were performed at the Ohio University multiphase test facility to evaluate the performance of a four path ultrasonic flow meter (UFM) in the presence of water in oil. The tests used a clear Perspex flow meter and piping, so that the flow behaviour could be observed and correlated with UFM performance. Tests were initially carried out at a wide range of water-cut (water volume fraction), in order to verify meter operation. These tests showed that at higher velocities the water was fully dispersed and UFM operation appeared normal, although the true flow rate performance of the meter could not evaluated due the the lack of a suitable reference measurement. At lower velocities, water separated and formed a {sup r}iver'' along the pipe bottom. Under some circumstances the bottom acoustic paths could fail to operate due to refraction and dispersion effects when the ultrasound encounters the oil/water interface region. Further tests were then carried out to attempt to quantify the UFM performance with water-cut in the range of 1% and 7%. For these tests, more of an attempt was made to quantify the uncertainty in flow rate measurement. At higher velocities, the combined oil and water volumetric flow rate measured by the UFM was within the experimental uncertainty of the test method. At lower flow rates, the performance of the flow meter was degraded by water drop out affecting the lower path velocity measurement. This paper describes the hydraulic behavior and gives advice on operational limits for good flow measurement in oil/water flows. The test data shows that the conditions in which good measurement can be obtained correspond well with the API4 guidelines for good mixing in sampling applications. (author) (tk)

  13. Horizontal Accelerator

    Data.gov (United States)

    Federal Laboratory Consortium — The Horizontal Accelerator (HA) Facility is a versatile research tool available for use on projects requiring simulation of the crash environment. The HA Facility is...

  14. Stratigraphic control and formation evaluation of horizontal wells with MWD

    Energy Technology Data Exchange (ETDEWEB)

    Hammons, L.R.B. (Eastman Teleco (United States)); Sellers, D.H.; Fisher, E.K. (Texaco Inc. (United States))

    1992-10-01

    Sandstone reservoirs in the Gulf of Mexico typically do not form horizontal planes, and a predetermined course for a horizontal well cannot ensure that the well path will remain within the producing interval throughout the horizontal section. Detecting approaching bed boundaries and fluid contacts early enough to make the changes necessary to keep the well path in the producing interval is an important technical issue during the planning and drilling of horizontal wells. This paper reports that the first two horizontal wells drilled in the Gulf of Mexico achieved this objective with measurement-while-drilling (MWD) resistivity measurements and with supporting computer modeling for bed boundary detection.

  15. Path Dependency

    OpenAIRE

    Mark Setterfield

    2015-01-01

    Path dependency is defined, and three different specific concepts of path dependency – cumulative causation, lock in, and hysteresis – are analyzed. The relationships between path dependency and equilibrium, and path dependency and fundamental uncertainty are also discussed. Finally, a typology of dynamical systems is developed to clarify these relationships.

  16. Culminating paths

    Directory of Open Access Journals (Sweden)

    Mireille Bousquet-Mélou

    2008-04-01

    Full Text Available Let a and b be two positive integers. A culminating path is a path of ℤ 2 that starts from (0,0, consists of steps (1,a and (1,-b, stays above the x-axis and ends at the highest ordinate it ever reaches. These paths were first encountered in bioinformatics, in the analysis of similarity search algorithms. They are also related to certain models of Lorentzian gravity in theoretical physics. We first show that the language on a two letter alphabet that naturally encodes culminating paths is not context-free. Then, we focus on the enumeration of culminating paths. A step by step approach, combined with the kernel method, provides a closed form expression for the generating function of culminating paths ending at a (generic height k. In the case a = b, we derive from this expression the asymptotic behaviour of the number of culminating paths of length n. When a > b, we obtain the asymptotic behaviour by a simpler argument. When a < b, we only determine the exponential growth of the number of culminating paths. Finally, we study the uniform random generation of culminating paths via various methods. The rejection approach, coupled with a symmetry argument, gives an algorithm that is linear when a ≥ b, with no precomputation stage nor non-linear storage required. The choice of the best algorithm is not as clear when a < b. An elementary recursive approach yields a linear algorithm after a precomputation stage involving O (n 3 arithmetic operations, but we also present some alternatives that may be more efficient in practice.

  17. Path Sensitization

    Institute of Scientific and Technical Information of China (English)

    赵著行; 闵应骅; 等

    1997-01-01

    For different delay models,the concept of sensitization can be very different.Traditonal concepts of sensitization cannot precisely describe circuit behavior when the input vectors change very fast.Using Boolean process aporoach,this paper presents a new definition of sensitization for arbitrary input waveforms.By this new concept it is found that if the inputs of a combinational circuit can change at any time,and each gate's delay varies within an interval (bounded gate delay model),then every path,which is not necessarily a single topological path,is sensitizable.From the experimental results it can be seen that,all nonsensitizable paths for traditional concepts actually can propagate transitions along them for some input waveforms.However,specified time between input transitions(STBIT) and minimum permissible pulse width(ε)are two major factors to make some paths non-sensitizable.

  18. Path Dependence

    DEFF Research Database (Denmark)

    Madsen, Mogens Ove

    Begrebet Path Dependence blev oprindelig udviklet inden for New Institutionel Economics af bl.a. David, Arthur og North. Begrebet har spredt sig vidt i samfundsvidenskaberne og undergået en udvikling. Dette paper propagerer for at der er sket så en så omfattende udvikling af begrebet, at man nu kan...... tale om 1. og 2. generation af Path Dependence begrebet. Den nyeste udvikling af begrebet har relevans for metodologi-diskusionerne i relation til Keynes...

  19. Horizontal drilling in Ontario

    Energy Technology Data Exchange (ETDEWEB)

    Sidey, P.; Precul, L. [Sproule Associates Ltd., Calgary, AB (Canada)

    2002-07-01

    A review of oil and gas production in Ontario was presented with particular reference to drilling activity between 1987 to mid 2002 when 1450 vertical wells were drilled, of which 1100 were for petroleum production and the remainder were for gas storage, observation wells, private gas wells and stratigraphic tests. Of the 1100 vertical wells drilled for petroleum production, 40 per cent became gas wells, 16 per cent became oil wells, 4 per cent became oil and gas wells, and 40 per cent were dry. During the same time period, 133 horizontal wells were also drilled, mostly for petroleum. The most active operator was Talisman Energy, which drilled 101 of the 133 horizontal wells. The remainder were drilled by 12 other companies. Of the horizontal wells, 64 per cent became oil wells, 19 per cent became gas wells, and 17 per cent were dry. This presentation included graphs depicting which oil and gas pools saw vertical or horizontal drilling during the designated time period, and explained how the wells were classified. Both horizontal and vertical well targets were illustrated. Particular reference was made to Talisman Energy's Lake Erie Drilling program which revealed that horizontal wells have an initial production rate that is 5 times that expected from vertical wells. The Hillman Pool case study revealed that the initial rate of the average horizontal well is less than half that of the average vertical well. Horizontal drilling in the Lake Erie Morpeth Gas pool has also been a commercial success. This paper demonstrates that operators have maintained Ontario's oil and gas production at high levels. In 1997 widespread horizontal drilling began taking place in Ontario, and since then, approximately 30 per cent of the wells drilled in the province have been horizontal. 16 figs.

  20. Path Creation

    DEFF Research Database (Denmark)

    Karnøe, Peter; Garud, Raghu

    2012-01-01

    This paper employs path creation as a lens to follow the emergence of the Danish wind turbine cluster. Supplier competencies, regulations, user preferences and a market for wind power did not pre-exist; all had to emerge in a tranformative manner involving multiple actors and artefacts. Competenc......This paper employs path creation as a lens to follow the emergence of the Danish wind turbine cluster. Supplier competencies, regulations, user preferences and a market for wind power did not pre-exist; all had to emerge in a tranformative manner involving multiple actors and artefacts....... Competencies emerged through processes and mechanisms such as co-creation that implicated multiple learning processes. The process was not an orderly linear one as emergent contingencies influenced the learning processes. An implication is that public policy to catalyse clusters cannot be based...

  1. Estudio del horizonte local

    OpenAIRE

    Ros Ferré, Rosa Maria

    2009-01-01

    El estudio del horizonte es fundamental para poder facilitar las primeras observaciones de los alumnos en un centro educativo. Un simple modelo, que debe realizarse para cada centro, nos permite facilitar el estudio y la comprensión de los primeros rudimentos astronómicos. El modelo construido se presenta a su vez como un sencillo modelo de reloj ecuatorial y a partir de él se pueden construir otros modelos (horizontal y vertical).

  2. Sliding Downhill Horizontally

    Science.gov (United States)

    Zurcher, Ulrich

    2005-04-01

    We study the motion of object sliding on a rough incline plane. The coefficient of kinetic friction between the surface and the object is such that the magnitude of the gravitational force along the incline F is equal to the magnitude of the kinetic friction S. If the initial velocity of the object is along the incline, the object slides down the incline with constant velocity. We study the case when the object in launched in horizontal direction. We derive exact expressions for the terminal speed of the object and the maximum horizontal displacement of the object.

  3. Horizontal Connection and Horizontal Mean Curvature in Carnot Groups

    Institute of Scientific and Technical Information of China (English)

    Kang Hai TAN; Xiao Ping YANG

    2006-01-01

    In this paper we give a geometric interpretation of the notion of the horizontal mean curvature which is introduced by Danielli-Garofalo-Nhieu and Pauls who recently introduced sub-Riemannian minimal surfaces in Carnot groups. This will be done by introducing a natural nonholonomic connection which is the restriction (projection) of the natural Riemannian connection on the horizontal bundle. For this nonholonomic connection and (intrinsic) regular hypersurfaces we introduce the notions of the horizontal second fundamental form and the horizontal shape operator. It turns out that the horizontal mean curvature is the trace of the horizontal shape operator.

  4. Horizontally mounted solar collector

    Science.gov (United States)

    Black, D. H. (Inventor)

    1979-01-01

    Solar energy is collected by using a vertical deflector assembly, a stationary reflector and a horizontally mounted solar collector. The deflector assembly contains a plurality of vanes which change the direction of the solar energy to the vertical, while constantly keeping the same side of the deflector facing the sun. The vertical rays are then reflected off the stationary reflector and are then absorbed by the collector.

  5. Horizontal drilling activity in Manitoba

    Energy Technology Data Exchange (ETDEWEB)

    Fox, J.

    1997-04-01

    An update of horizontal well drilling in Manitoba was provided. Manitoba`s productive formations are: (1) the Bakken Formation, (2) the Lodgepole Formation, (3) the Mission Canyon Formation, (4) the Amaranth Formation, and (5) the Melita Formation. A total of 28 exploratory wells and 29 development wells, including 11 horizontal wells were drilled in 1996. The 11 horizontal wells accounted for 30 per cent of the drilling meterage. The leading drillers for horizontal wells in Manitoba are Tundra Oil and Gas, Chevron, Anderson and HCO. Production from horizontal wells in 1996 totaled 310 cubic meter per day. To date, no horizontal wells have been drilled in the Bakken Formation. The least successful horizontal well application has been in the Lodgepole Formation. A summary of horizontal well production was provided for each Formation. 4 tabs., 10 figs.

  6. Path homogeneity along a horizontal line-of-sight path during the FESTER experiment: First results

    NARCIS (Netherlands)

    Gunter, W.H.; Maritz, B.; Koago, M.; Wainman, C.K.; Gardener, M.E.; February, F.; Eijk, A.M.J. van

    2016-01-01

    The First European South African Experiment (FESTER) was conducted over about a 10 month period at the Institute of Maritime Technology (IMT) in False Bay, South Africa. One of the important goals was the establishment of the air-sea temperature difference (ASTD) homogeneity along the main

  7. Well Spacing for Horizontal Wells

    Directory of Open Access Journals (Sweden)

    C.D.S. Keuengoua

    2011-06-01

    Full Text Available In the developing phase of a hydrocarbon reservoir and planning for drilling the production wells, it is necessary to drill the wells in an appropriate spacing to achieve maximum economic revenues during the reservoir life span. Well spacing which is the real location and interrelationship between producing oil or gas wells in an oil field is an important parameter. It is determined for the maximum ultimate production of a given reservoir and should be taken in consideration during well planning to avoid drilling of unnecessary wells. This study presents the concept of drainage area on horizontal well and horizontal productivity indices with different equations and their applications. A user friendly Excel Spreadsheet program was developed to calculate the productivity values of horizontal wells using three major available productivity equations. Also, the developed spreadsheet program was used to evaluate the effect of well spacing on the productivities of horizontal wells using productivity index approach and drainage area concept. It also helps to review the comparison between vertical and horizontal wells spacing based on drainage area concept. This program was validated, and then was used to study the effect of horizontal well length on the ratio of horizontal well productivity to vertical well productivity. The results show that higher ratio of horizontal well productivity to vertical well productivity values are obtained with increase length of the horizontal well. It is a very useful tool for making decision about the application of well spacing for horizontal wells.

  8. PRODUCTIVITY OF FRACTURED HORIZONTAL WELLS

    Directory of Open Access Journals (Sweden)

    Stjepan Antolović

    2009-12-01

    Full Text Available The interest and performance of horizontal drilling and completions has increased during the last two decades. Horizontal wells are advantageous compared to vertical wells in thin reservoirs, reservoirs with favorable vertical permeability and reservoirs with water and gas coning problems. In many reservoirs, the ratio of horizontal permeability to the vertical permeability is substantially larger than one and often is close to 10. Thus, these reservoirs are very good candidates for hydraulic fracturing. By hydraulic fracturing one or more fractures are created, which can be longitudinal or orthogonal. By that, flow is altered and it mostly conducts horizontally through reservoir toward horizontal wellbore. With this altered flow, fluid is produced faster, with less pressure loss by fluid unit of produced fluid. Some of the existing mathematical models to determine the productivity of multifractured horizontal wells are presented in this work (the paper is published in Croatian.

  9. Line-of-Sight Path Following for Dubins Paths with Adaptive Sideslip Compensation of Drift Forces

    DEFF Research Database (Denmark)

    Fossen, Thor Inge; Pettersen, Kristin Ytterstad; Galeazzi, Roberto

    2015-01-01

    guidance law is intended for maneuvering in the horizontal-plane at given speeds and typical applications are marine craft, autonomous underwater vehicles (AUVs), unmanned aerial vehicles (UAVs) as well as other vehicles and craft where the goal is to follow a predefined parametrized curve without time......We present a nonlinear adaptive path-following controller that compensates for drift forces through vehicle sideslip. Vehicle sideslip arises during path following when the vehicle is subject to drift forces caused by ocean currents, wind and waves. The proposed algorithm is motivated by a lineof...... constraints. Two vehicle cases studies are included to verify the theoretical results....

  10. Horizontal and Vertical Line Designs.

    Science.gov (United States)

    Johns, Pat

    2003-01-01

    Presents an art lesson in which students learn about the artist Piet Mondrian and create their own abstract artworks. Focuses on geometric shapes using horizontal and vertical lines. Includes background information about the artist. (CMK)

  11. Experimental investigation of horizontal convection

    OpenAIRE

    Muñoz Córdoba, Lucía

    2015-01-01

    Fluid circulation driven by buoyancy forces due to a thermal gradient on a horizontal boundary, known as horizontal convection, is experimentally studied. For that purpose, a methacrylate box with inner dimensions 300x150x150 mm3 (LxWxH) whose bottom is composed by a heat exchanger and a printed circuit board is lled with water. The heat exchanger provides a uniform temperature boundary condition while the printed circuit board provides a boundary condition of uniform heat ...

  12. Following Control for a UUV using Temporary Path Generation Guidance

    Institute of Scientific and Technical Information of China (English)

    Zheping Yan; Dongnan Chi; Jiajia Zhou; Yufei Zhao

    2012-01-01

    A path following control algorithm for an unmanned underwater vehicle (UUV) using temporary path generation guidance was proposed in this paper.Owing to different initial states of the vehicle,such as position and orientation,the path following control in the horizontal plane may yield a poor performance.To deal with the negative effect induced by initial states,a temporary path generation was presented based on the relationship between the original reference path and the vehicle's initial states.With different relative positions between the vehicle and reference path,including out of straight lines,as well as inside and outside a circle,the related temporary paths guiding the vehicle to the reference path were able to be generated in real time.The vehicle was guided to steer along the temporary path until it reached the tangent point at the reference path,where the controller was designed using the input-output feedback linearization method.Simulation results demonstrated that the proposed algorithm is effective under the three different situations mentioned above.

  13. Near-term Horizontal Launch for Flexible Operations: Results of the DARPA/NASA Horizontal Launch Study

    Science.gov (United States)

    Bartolotta, Paul A.; Wilhite, Alan W.; Schaffer, Mark G.; Huebner, Lawrence D.; Voland, Randall T.; Voracek, David F.

    2012-01-01

    Horizontal launch has been investigated for 60 years by over 130 different studies. During this time only one concept, Pegasus, has ever been in operation. The attractiveness of horizontal launch is the capability to provide a "mobile launch pad" that can use existing aircraft runways, cruise above weather, loiter for mission instructions, and provide precise placement for orbital intercept, rendezvous, or reconnaissance. A jointly sponsored study by DARPA and NASA, completed in 2011, explored the trade space of horizontal launch system concepts which included an exhaustive literature review of the past 70 years. The Horizontal Launch Study identified potential near- and mid-term concepts capable of delivering 15,000 lb payloads to a 28.5 due East inclination, 100 nautical-mile low-Earth orbit. Results are presented for a range of near-term system concepts selected for their availability and relatively low design, development, test, and evaluation (DDT&E) costs. This study identified a viable low-cost development path forward to make a robust and resilient horizontal launch capability a reality.

  14. Path Integrals and Hamiltonians

    Science.gov (United States)

    Baaquie, Belal E.

    2014-03-01

    1. Synopsis; Part I. Fundamental Principles: 2. The mathematical structure of quantum mechanics; 3. Operators; 4. The Feynman path integral; 5. Hamiltonian mechanics; 6. Path integral quantization; Part II. Stochastic Processes: 7. Stochastic systems; Part III. Discrete Degrees of Freedom: 8. Ising model; 9. Ising model: magnetic field; 10. Fermions; Part IV. Quadratic Path Integrals: 11. Simple harmonic oscillators; 12. Gaussian path integrals; Part V. Action with Acceleration: 13. Acceleration Lagrangian; 14. Pseudo-Hermitian Euclidean Hamiltonian; 15. Non-Hermitian Hamiltonian: Jordan blocks; 16. The quartic potential: instantons; 17. Compact degrees of freedom; Index.

  15. Path Problems in Networks

    CERN Document Server

    Baras, John

    2010-01-01

    The algebraic path problem is a generalization of the shortest path problem in graphs. Various instances of this abstract problem have appeared in the literature, and similar solutions have been independently discovered and rediscovered. The repeated appearance of a problem is evidence of its relevance. This book aims to help current and future researchers add this powerful tool to their arsenal, so that they can easily identify and use it in their own work. Path problems in networks can be conceptually divided into two parts: A distillation of the extensive theory behind the algebraic path pr

  16. Horizontal fiscal imbalance in Germany

    Directory of Open Access Journals (Sweden)

    Paweł Kowalik

    2015-04-01

    Full Text Available Regional inequalities are currently a challenge for the majority of the countries, in particular the large ones. The problem of public income redistribution emerges due to possible differentiation of the economic development level of territorial units. The most often considered problem is the vertical distribution. The horizontal division of income is far less frequently considered. Horizontal fiscal imbalance or regional tax inequalities seem to be graver than the vertical imbalance, particularly in developing countries. The public finance system, in particular in federations, is often very complex. Public finance of federations and federated states are not often based on the same assumptions. This leads to differences among regions, both vertical and horizontal. The use of the presented measures helps identify those differences and permits developing mechanisms equalising those inequalities. It should be remembered that those measures may have certain drawbacks, and they mainly focus on certain specific values of income redistribution. Thereby several measures should be applied in measurements and the obtained results should be compared. There are no up-to-date measurements and comparisons of horizontal fiscal imbalance among countries.. The aim of this paper is to measure horizontal fiscal imbalance in Germany, especially after reunification, which represents one of two models of federalism. At the beginning it shows the static and dynamic measurements presented in the literature that can be used to measure the horizontal fiscal imbalance. And then it is followed by the results of calculations for Germany in the period 1970-2013. As expected, horizontal imbalance was much lower before than after the reunification of Germany. After the reunification there were large disparities between "old" and "new" länder. This imbalance is gradually reduced. In comparison with the results obtained for the USA [Kowalik 2014, pp. 144-148] it can be said

  17. Multi-Dimensional Path Queries

    DEFF Research Database (Denmark)

    Bækgaard, Lars

    1998-01-01

    We present the path-relationship model that supports multi-dimensional data modeling and querying. A path-relationship database is composed of sets of paths and sets of relationships. A path is a sequence of related elements (atoms, paths, and sets of paths). A relationship is a binary path...... to create nested path structures. We present an SQL-like query language that is based on path expressions and we show how to use it to express multi-dimensional path queries that are suited for advanced data analysis in decision support environments like data warehousing environments...

  18. A Min-max Relation for Monotone Path Systems in Simple Regions

    DEFF Research Database (Denmark)

    Cameron, Kathleen

    1996-01-01

    A monotone path system (MPS) is a finite set of pairwise disjointpaths (polygonal arcs) in the plane such that every horizontal line intersectseach of the paths in at most one point. We consider a simple polygon in thexy-plane which bounds the simple polygonal (closed) region D. Let T and B betwo...

  19. Unique Path Partitions

    DEFF Research Database (Denmark)

    Bessenrodt, Christine; Olsson, Jørn Børling; Sellers, James A.

    2013-01-01

    We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions.......We give a complete classification of the unique path partitions and study congruence properties of the function which enumerates such partitions....

  20. Path dependence and creation

    DEFF Research Database (Denmark)

    Garud, Raghu; Karnøe, Peter

    the place of agency in these theories that take history so seriously. In the end, they are as interested in path creation and destruction as they are in path dependence. This book is compiled of both theoretical and empirical writing. It shows relatively well-known industries such as the automobile...

  1. DRILL BITS FOR HORIZONTAL WELLS

    Directory of Open Access Journals (Sweden)

    Paolo Macini

    1996-12-01

    Full Text Available This paper underlines the importance of the correct drill bit application in horizontal wells. Afler the analysis of the peculiarities of horizontal wells and drainholes drilling techniques, advantages and disadvantages of the application of both roller cone and fixed cutters drill bits have been discussed. Also, a review of the potential specific featuries useful for a correct drill bit selection in horizontal small diameter holes has been highlighted. Drill bits for these special applications, whose importance is quickly increasing nowadays, should be characterised by a design capable to deliver a good penetration rate low WOB, and, at the same time, be able to withstand high RPM without premature cutting structure failure and undergauge. Formation properties will also determine the cutting structure type and the eventual specific features for additional gauge and shoulder protection.

  2. Free path groupoid grading on Leavitt path algebras

    OpenAIRE

    Goncalves, Daniel; Yoneda, Gabriela

    2015-01-01

    In this work we realize Leavitt path algebras as partial skew groupoid rings. This yields a free path groupoid grading on Leavitt path algebras. Using this grading we characterize free path groupoid graded isomorphisms of Leavitt path algebras that preserves generators.

  3. Horizontal drilling pilot in a shallow heavy oil reservoir in the Suplac Field in Northwestern Romania

    Energy Technology Data Exchange (ETDEWEB)

    Lavelle, J.; Yaghoobi, A. [OMV Petrom S.A. (Romania)

    2011-07-01

    The Suplac field situated in north-western Romania is a shallow and heavy oil deposit lying at depths of between 40 and 200 meters. The deposit has been exploited since 1964 using different techniques but some areas of the reservoir located beneath villages and steep hills were never reached. The aim of this paper is to describe a project using horizontal alternating steam drive (HASD) to harvest oil from these areas by turning from vertical to horizontal. A pilot test was conducted over 4 months in 2010 with 3 parallel horizontal wells. The rig equipment, the well path designs and the directional difficulties are discussed herein. Results showed that horizontals could be drilled using a vertical mast rig and all the expectations were met. The success of this pilot project was highlighted herein and the company is now planning on continuing with a horizontal development program; however wellbore clean out is a remaining challenge.

  4. Path Creation, Path Dependence and Breaking Away from the Path

    DEFF Research Database (Denmark)

    Wang, Jens Erik; Hedman, Jonas; Tuunainen, Virpi Kristiina

    2016-01-01

    The explanation of how and why firms succeed or fail is a recurrent research challenge. This is particularly important in the context of technological innovations. We focus on the role of historical events and decisions in explaining such success and failure. Using a case study of Nokia, we develop...... the importance of intermediate outcomes, which in the case of Nokia was the importance of software ecosystems and adaptable mobile devices. Furthermore, we show how the layers of path dependence mutually reinforce each other and become stronger....

  5. Zero-Slack, Noncritical Paths

    Science.gov (United States)

    Simons, Jacob V., Jr.

    2017-01-01

    The critical path method/program evaluation and review technique method of project scheduling is based on the importance of managing a project's critical path(s). Although a critical path is the longest path through a network, its location in large projects is facilitated by the computation of activity slack. However, logical fallacies in…

  6. Horizontal Diplopia Following Upper Blepharoplasty

    Directory of Open Access Journals (Sweden)

    Tomás Ortiz-Basso

    2014-09-01

    Full Text Available Diplopia is an infrequent complication after blepharoplasty. Most of the cases are in its vertical form due to trauma of the extraocular muscles. In this article, we present a case of horizontal diplopia following cosmetic upper blepharoplasty; we review the literature on this unexpected complication and offer some recommendations to avoid it.

  7. Tortuous path chemical preconcentrator

    Science.gov (United States)

    Manginell, Ronald P.; Lewis, Patrick R.; Adkins, Douglas R.; Wheeler, David R.; Simonson, Robert J.

    2010-09-21

    A non-planar, tortuous path chemical preconcentrator has a high internal surface area having a heatable sorptive coating that can be used to selectively collect and concentrate one or more chemical species of interest from a fluid stream that can be rapidly released as a concentrated plug into an analytical or microanalytical chain for separation and detection. The non-planar chemical preconcentrator comprises a sorptive support structure having a tortuous flow path. The tortuosity provides repeated twists, turns, and bends to the flow, thereby increasing the interfacial contact between sample fluid stream and the sorptive material. The tortuous path also provides more opportunities for desorption and readsorption of volatile species. Further, the thermal efficiency of the tortuous path chemical preconcentrator is comparable or superior to the prior non-planar chemical preconcentrator. Finally, the tortuosity can be varied in different directions to optimize flow rates during the adsorption and desorption phases of operation of the preconcentrator.

  8. Career Path Descriptions

    CERN Document Server

    Charkiewicz, A

    2000-01-01

    Before the Career Path system, jobs were classified according to grades with general statutory definitions, guided by the "Job Catalogue" which defined 6 evaluation criteria with example illustrations in the form of "typical" job descriptions. Career Paths were given concise statutory definitions necessitating a method of description and evaluation adapted to their new wider-band salary concept. Evaluations were derived from the same 6 criteria but the typical descriptions became unusable. In 1999, a sub-group of the Standing Concertation Committee proposed a new guide for describing Career Paths, adapted to their wider career concept by expanding the 6 evaluation criteria into 9. For each criterion several levels were established tracing the expected evolution of job level profiles and personal competencies over their longer salary ranges. While providing more transparency to supervisors and staff, the Guide's official use would be by services responsible for vacancy notices, Career Path evaluations and rela...

  9. Path Optimization Using APSO

    Directory of Open Access Journals (Sweden)

    Deepak Goyal

    2013-07-01

    Full Text Available This paper addresses the malicious node detection and path optimization problem for wireless sensor networks. Malicious node detection in neighborhood is a needed because that node may cause incorrect decisions or energy depletion. In this paper APSO (combination of Artificial bee colony and particular swarm optimization is used to choose an optimized path. Through this improved version we will overcome the disadvantage of local optimal which comes when we use PSO approach.

  10. Paths to nursing leadership.

    Science.gov (United States)

    Bondas, Terese

    2006-07-01

    The aim was to explore why nurses enter nursing leadership and apply for a management position in health care. The study is part of a research programme in nursing leadership and evidence-based care. Nursing has not invested enough in the development of nursing leadership for the development of patient care. There is scarce research on nurses' motives and reasons for committing themselves to a career in nursing leadership. A strategic sample of 68 Finnish nurse leaders completed a semistructured questionnaire. Analytic induction was applied in an attempt to generate a theory. A theory, Paths to Nursing Leadership, is proposed for further research. Four different paths were found according to variations between the nurse leaders' education, primary commitment and situational factors. They are called the Path of Ideals, the Path of Chance, the Career Path and the Temporary Path. Situational factors and role models of good but also bad nursing leadership besides motivational and educational factors have played a significant role when Finnish nurses have entered nursing leadership. The educational requirements for nurse leaders and recruitment to nursing management positions need serious attention in order to develop a competent nursing leadership.

  11. Examination of the Cooray-Rubinstein (C-R) formula for a mixed propagation path by using FDTD

    National Research Council Canada - National Science Library

    Qilin Zhang; Dongshuai Li; Yanfeng Fan; Yuanyuan Zhang; Jinge Gao

    2012-01-01

    ... (vertically stratified conductivity) and estimate the lightning horizontal electric fields over the mixed path, and we have examined its accuracy at distances of 100 m to 1000 m from the lightning channel by using finite difference time domain (FDTD...

  12. Horizontally oriented plates in clouds

    CERN Document Server

    Bréon, François-Marie

    2011-01-01

    Horizontally oriented plates in clouds generate a sharp specular reflectance signal in the glint direction, often referred to as "subsun". This signal (amplitude and width) may be used to analyze the relative area fraction of oriented plates in the cloud top layer and their characteristic tilt angle to the horizontal. We make use of spaceborne measurements from the POLDER instrument to provide a statistical analysis of these parameters. More than half of the clouds show a detectable maximum reflectance in the glint direction, although this maximum may be rather faint. The typical effective fraction (area weighted) of oriented plates in clouds lies between 10-3 and 10-2. For those oriented plates, the characteristic tilt angle is less than 1 degree in most cases. These low fractions imply that the impact of oriented plates on the cloud albedo is insignificant. The largest proportion of clouds with horizontally oriented plates is found in the range 500-700 hPa, in agreement with typical in situ observation of p...

  13. Partial Horizontal Laryngectomy and Epiglottiplasty

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    In order to evaluate the availability of the lateral horizontal laryngectomy and anaplasty of epiglottis to treat somepatients with specific supraglottic carcinomas and hypopharyngeal carcinomas, 17 cases of laryngeal and hypopharyngeal carcinomas were retrospectively analyzed, whose tumors were located at the lateral margin of epiglottis, aryepiglottic fold, medial wall of piriformfossa and were treated by the lateral horizontal laryngectomy and anaplasty of epiglottis. The results showed that all cases took food by mouth in postoperative 9-14 days and subjected to decannulation in postoperative 9-15 days. Three cases had postoperative hoarse voice. The free-disease survival rate of 3 years was 71.4 % in 14 cases followed up after the first surgical therapy, and the overall free-disease survival rate of 3 years was 85.7 % after the second surgical therapy. It was concluded that the manipulations of the lateral horizontal laryngectomy and epiglottiplasty were simple. It could alleviate the postoperative symptoms of aspiration and bucking remarkably and shorten their postoperative recovery time, yet does not lower the survival rate of patients if laryngocarcinoma or hypopharyngeal carcinoma cases were properly selected.

  14. The effect of varying path properties in path steering tasks

    NARCIS (Netherlands)

    Liu, L.; Liere, R. van

    2010-01-01

    Path steering is a primitive 3D interaction task that requires the user to navigate through a path of a given length and width. In a previous paper, we have conducted controlled experiments in which users operated a pen input device to steer a cursor through a 3D path subject to fixed path propertie

  15. Shortest Paths in Microseconds

    CERN Document Server

    Agarwal, Rachit; Godfrey, P Brighten; Zhao, Ben Y

    2013-01-01

    Computing shortest paths is a fundamental primitive for several social network applications including socially-sensitive ranking, location-aware search, social auctions and social network privacy. Since these applications compute paths in response to a user query, the goal is to minimize latency while maintaining feasible memory requirements. We present ASAP, a system that achieves this goal by exploiting the structure of social networks. ASAP preprocesses a given network to compute and store a partial shortest path tree (PSPT) for each node. The PSPTs have the property that for any two nodes, each edge along the shortest path is with high probability contained in the PSPT of at least one of the nodes. We show that the structure of social networks enable the PSPT of each node to be an extremely small fraction of the entire network; hence, PSPTs can be stored efficiently and each shortest path can be computed extremely quickly. For a real network with 5 million nodes and 69 million edges, ASAP computes a short...

  16. Faster Replacement Paths

    CERN Document Server

    Williams, Virginia Vassilevska

    2010-01-01

    The replacement paths problem for directed graphs is to find for given nodes s and t and every edge e on the shortest path between them, the shortest path between s and t which avoids e. For unweighted directed graphs on n vertices, the best known algorithm runtime was \\tilde{O}(n^{2.5}) by Roditty and Zwick. For graphs with integer weights in {-M,...,M}, Weimann and Yuster recently showed that one can use fast matrix multiplication and solve the problem in O(Mn^{2.584}) time, a runtime which would be O(Mn^{2.33}) if the exponent \\omega of matrix multiplication is 2. We improve both of these algorithms. Our new algorithm also relies on fast matrix multiplication and runs in O(M n^{\\omega} polylog(n)) time if \\omega>2 and O(n^{2+\\eps}) for any \\eps>0 if \\omega=2. Our result shows that, at least for small integer weights, the replacement paths problem in directed graphs may be easier than the related all pairs shortest paths problem in directed graphs, as the current best runtime for the latter is \\Omega(n^{2.5...

  17. Smoothing of Piecewise Linear Paths

    Directory of Open Access Journals (Sweden)

    Michel Waringo

    2008-11-01

    Full Text Available We present an anytime-capable fast deterministic greedy algorithm for smoothing piecewise linear paths consisting of connected linear segments. With this method, path points with only a small influence on path geometry (i.e. aligned or nearly aligned points are successively removed. Due to the removal of less important path points, the computational and memory requirements of the paths are reduced and traversing the path is accelerated. Our algorithm can be used in many different applications, e.g. sweeping, path finding, programming-by-demonstration in a virtual environment, or 6D CNC milling. The algorithm handles points with positional and orientational coordinates of arbitrary dimension.

  18. TRACING EFFICIENT PATH USING WEB PATH TRACING

    Directory of Open Access Journals (Sweden)

    L.K. Joshila Grace

    2014-01-01

    Full Text Available In the fast improving society, people depend on online purchase of goods than spending time physically. So there are lots of resources emerged for this online buying and selling of materials. Efficient and attractive web sites would be the best to sell the goods to people. To know whether a web site is reaching the mind of the customers or not, a high speed analysis is done periodically by the web developers. This works helps for the web site developers in knowing the weaker and stronger section of their web site. Parameters like frequency and utility are used for quantitative and qualitative analysis respectively. Addition to this down loads, book marks and the like/dislike of the particular web site is also considered. A new web path trace tree structure is implemented. A mathematical implementation is done to predict the efficient pattern used by the web site visitors.

  19. Euclidean shortest paths

    CERN Document Server

    Li, Fajie

    2011-01-01

    This unique text/reference reviews algorithms for the exact or approximate solution of shortest-path problems, with a specific focus on a class of algorithms called rubberband algorithms. Discussing each concept and algorithm in depth, the book includes mathematical proofs for many of the given statements. Topics and features: provides theoretical and programming exercises at the end of each chapter; presents a thorough introduction to shortest paths in Euclidean geometry, and the class of algorithms called rubberband algorithms; discusses algorithms for calculating exact or approximate ESPs i

  20. Panspermia and horizontal gene transfer

    Science.gov (United States)

    Klyce, Brig

    2009-08-01

    Evidence that extremophiles are hardy and ubiquitous is helping to make panspermia a respectable theory. But even if life on Earth originally came from space, biologists assume that the subsequent evolution of life is still governed by the darwinian paradigm. In this review we show how panspermia could amend darwinism and point to a cosmic source for, not only extremophiles but, all of life. This version of panspermia can be called "strong panspermia." To support this theory we will discuss recent evidence pertaining to horizontal gene transfer, viruses, genes apparently older than the Earthly evolution of the features they encode, and primate-specific genes without identifiable precursors.

  1. Test Bed For Control Of Optical-Path Lengths

    Science.gov (United States)

    O'Neal, Michael C.; Eldred, Daniel D.; Liu, Dankai; Redding, David C.

    1994-01-01

    Truss structure and ancillary equipment constitute test bed for experiments in methods of controlling lengths of optical paths under conditions of structural vibration and deformation. Accommodates both passive and active methods of control. Experimental control system reduces millimeter-level disturbances in optical path length to nanometers. Developed for control, alignment, and aiming of distributed optical systems on large flexible structures. Test bed includes tower 2.5 meters high with two horizontal arms extending at right angles from its top. Rigidly mounted on massive steel block providing measure of isolation from ground vibrations. Optical motion-compensation system similar to one described previously in NASA Tech Briefs enclosed in flexure-mounted frame, called "trolley," at end of longer horizontal arm.

  2. An Unplanned Path

    Science.gov (United States)

    McGarvey, Lynn M.; Sterenberg, Gladys Y.; Long, Julie S.

    2013-01-01

    The authors elucidate what they saw as three important challenges to overcome along the path to becoming elementary school mathematics teacher leaders: marginal interest in math, low self-confidence, and teaching in isolation. To illustrate how these challenges were mitigated, they focus on the stories of two elementary school teachers--Laura and…

  3. Reparametrizations of Continuous Paths

    DEFF Research Database (Denmark)

    Fahrenberg, Uli; Raussen, Martin

    2007-01-01

    compare it to the distributive lattice of countable subsets of the unit interval. The results obtained are used to analyse the space of traces in a topological space, i.e., the space of continuous paths up to reparametrization equivalence. This space is shown to be homeomorphic to the space of regular...

  4. MEASURING PATH DEPENDENCY

    Directory of Open Access Journals (Sweden)

    Peter Juhasz

    2017-03-01

    Full Text Available While risk management gained popularity during the last decades even some of the basic risk types are still far out of focus. One of these is path dependency that refers to the uncertainty of how we reach a certain level of total performance over time. While decision makers are careful in accessing how their position will look like the end of certain periods, little attention is given how they will get there through the period. The uncertainty of how a process will develop across a shorter period of time is often “eliminated” by simply choosing a longer planning time interval, what makes path dependency is one of the most often overlooked business risk types. After reviewing the origin of the problem we propose and compare seven risk measures to access path. Traditional risk measures like standard deviation of sub period cash flows fail to capture this risk type. We conclude that in most cases considering the distribution of the expected cash flow effect caused by the path dependency may offer the best method, but we may need to use several measures at the same time to include all the optimisation limits of the given firm

  5. Horizontal gene transfer in chromalveolates

    Directory of Open Access Journals (Sweden)

    Bhattacharya Debashish

    2007-09-01

    Full Text Available Abstract Background Horizontal gene transfer (HGT, the non-genealogical transfer of genetic material between different organisms, is considered a potentially important mechanism of genome evolution in eukaryotes. Using phylogenomic analyses of expressed sequence tag (EST data generated from a clonal cell line of a free living dinoflagellate alga Karenia brevis, we investigated the impact of HGT on genome evolution in unicellular chromalveolate protists. Results We identified 16 proteins that have originated in chromalveolates through ancient HGTs before the divergence of the genera Karenia and Karlodinium and one protein that was derived through a more recent HGT. Detailed analysis of the phylogeny and distribution of identified proteins demonstrates that eight have resulted from independent HGTs in several eukaryotic lineages. Conclusion Recurring intra- and interdomain gene exchange provides an important source of genetic novelty not only in parasitic taxa as previously demonstrated but as we show here, also in free-living protists. Investigating the tempo and mode of evolution of horizontally transferred genes in protists will therefore advance our understanding of mechanisms of adaptation in eukaryotes.

  6. Horizontal versus vertical plate motions

    Directory of Open Access Journals (Sweden)

    M. Cuffaro

    2006-07-01

    Full Text Available We review both present and past motions at major plate boundaries, which have the horizontal component in average 10 to 100 times faster (10–100 mm/yr than the vertical component (0.01–1 mm/yr in all geodynamic settings. The steady faster horizontal velocity of the lithosphere with respect to the upward or downward velocities at plate boundaries supports dominating tangential forces acting on plates. This suggests a passive role of plate boundaries with respect to far field forces determining the velocity of plates. The forces acting on the lithosphere can be subdivided in coupled and uncoupled, as a function of the shear at the lithosphere base. Higher the asthenosphere viscosity, more significant should be the coupled forces, i.e., the mantle drag and the trench suction. Lower the asthenosphere viscosity, more the effects of uncoupled forces might result determinant, i.e., the ridge push, the slab pull and the tidal drag. Although a combination of all forces acting on the lithosphere is likely, the decoupling between lithosphere and mantle suggests that a torque acts on the lithosphere independently of the mantle drag. Slab pull and ridge push are candidates for generating this torque, but, unlike these boundary forces, the advantage of the tidal drag is to be a volume force, acting simultaneously on the whole plates, and being the decoupling at the lithosphere base controlled by lateral variations in viscosity of the low-velocity layer.

  7. Explorando nuevos horizontes en NASA

    Science.gov (United States)

    Villanueva, G. L.

    A pesar de la incesante expansión del Universo iniciada con el Big Bang 14 mil millones de años atrás, nuestro Universo se siente cada día más cercano. La inquebrantable vocación de la humanidad por descubrir nuevos horizontes ha permitido el acercamiento de civilizaciones en nuestro planeta y nos ha permitido conocer nuestro lugar en el Universo como nunca antes. En este artículo presento una breve sinopsis de nuestro trabajo que se relaciona con diversas investigaciones con implicaciones astrobiológicas, desde el origen de los ingredientes de la "sopa de la vida", hasta la evolución y composición de la atmósfera de Marte.

  8. Cosmological Feynman Paths

    CERN Document Server

    Chew, Geoffrey F

    2008-01-01

    Arrowed-time divergence-free rules or cosmological quantum dynamics are formulated through stepped Feynman paths across macroscopic slices of Milne spacetime. Slice boundaries house totally-relativistic rays representing elementary entities--preons. Total relativity and the associated preon Fock space, despite distinction from special relativity (which lacks time arrow), are based on the Lorentz group. Each path is a set of cubic vertices connected by straight, directed and stepped arcs that carry inertial, electromagnetic and gravitational action. The action of an arc step comprises increments each bounded by Planck's constant. Action from extremely-distant sources is determined by universe mean energy density. Identifying the arc-step energy that determines inertial action with that determining gravitational action establishes both arc-step length and universe density. Special relativity is accurate for physics at laboratory spacetime scales far below that of Hubble and far above that of Planck.

  9. Nonadiabatic transition path sampling

    Science.gov (United States)

    Sherman, M. C.; Corcelli, S. A.

    2016-07-01

    Fewest-switches surface hopping (FSSH) is combined with transition path sampling (TPS) to produce a new method called nonadiabatic path sampling (NAPS). The NAPS method is validated on a model electron transfer system coupled to a Langevin bath. Numerically exact rate constants are computed using the reactive flux (RF) method over a broad range of solvent frictions that span from the energy diffusion (low friction) regime to the spatial diffusion (high friction) regime. The NAPS method is shown to quantitatively reproduce the RF benchmark rate constants over the full range of solvent friction. Integrating FSSH within the TPS framework expands the applicability of both approaches and creates a new method that will be helpful in determining detailed mechanisms for nonadiabatic reactions in the condensed-phase.

  10. PATHS groundwater hydrologic model

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, R.W.; Schur, J.A.

    1980-04-01

    A preliminary evaluation capability for two-dimensional groundwater pollution problems was developed as part of the Transport Modeling Task for the Waste Isolation Safety Assessment Program (WISAP). Our approach was to use the data limitations as a guide in setting the level of modeling detail. PATHS Groundwater Hydrologic Model is the first level (simplest) idealized hybrid analytical/numerical model for two-dimensional, saturated groundwater flow and single component transport; homogeneous geology. This document consists of the description of the PATHS groundwater hydrologic model. The preliminary evaluation capability prepared for WISAP, including the enhancements that were made because of the authors' experience using the earlier capability is described. Appendixes A through D supplement the report as follows: complete derivations of the background equations are provided in Appendix A. Appendix B is a comprehensive set of instructions for users of PATHS. It is written for users who have little or no experience with computers. Appendix C is for the programmer. It contains information on how input parameters are passed between programs in the system. It also contains program listings and test case listing. Appendix D is a definition of terms.

  11. Optimization of horizontal well staggered patterns

    Institute of Scientific and Technical Information of China (English)

    Zhao Chunsen; Li Peijing; Guan Dan; Liu Qingjuan

    2008-01-01

    Staggered line-drive patterns are widely used in oilfields. In this paper, to optimize a staggered pattern of horizontal wells, a 3D problem was divided into two 2D (x-y plane and y-z plane) problems with the pseudo-3D method, conformal transformation and superposition principle. A productivity equation for a horizontal well was deduced, which can be used to optimize the well pattern. A relationship between the length of horizontal wells and the shape factor of well patterns was established. The result shows that optimized well patterns can improve oil production from horizontal wells. This provides a theoretical basis for horizontal well applications to the development of oilfieids, especially for overall development of oilfields by horizontal wells.

  12. Path planning in dynamic environments

    NARCIS (Netherlands)

    Berg, J.P. van den

    2007-01-01

    Path planning plays an important role in various fields of application, such as CAD design, computer games and virtual environments, molecular biology, and robotics. In its most general form, the path planning problem is formulated as finding a collision-free path for a moving entity between a start

  13. Dynamic Surface and Active Disturbance Rejection Control for Path Following of an Underactuated UUV

    OpenAIRE

    Juan Li; Haitao Gao; Jiajia Zhou; Zheping Yan

    2014-01-01

    This paper addresses the problem of accurate path following control for an underactuated unmanned underwater vehicle (UUV) in the horizontal plane. For an underactuated UUV, the line-of-sight (LOS) guidance method is adopted to map 2D reference trajectory into a desired orientation, and through the tracking of heading to achieve path following, where the sideslip is introduced to modify the desired orientation. In this paper, we propose a method called dynamic surface and active disturbance r...

  14. Widespread horizontal transfer of retrotransposons.

    Science.gov (United States)

    Walsh, Ali Morton; Kortschak, R Daniel; Gardner, Michael G; Bertozzi, Terry; Adelson, David L

    2013-01-15

    In higher organisms such as vertebrates, it is generally believed that lateral transfer of genetic information does not readily occur, with the exception of retroviral infection. However, horizontal transfer (HT) of protein coding repetitive elements is the simplest way to explain the patchy distribution of BovB, a long interspersed element (LINE) about 3.2 kb long, that has been found in ruminants, marsupials, squamates, monotremes, and African mammals. BovB sequences are a major component of some of these genomes. Here we show that HT of BovB is significantly more widespread than believed, and we demonstrate the existence of two plausible arthropod vectors, specifically reptile ticks. A phylogenetic tree built from BovB sequences from species in all of these groups does not conform to expected evolutionary relationships of the species, and our analysis indicates that at least nine HT events are required to explain the observed topology. Our results provide compelling evidence for HT of genetic material that has transformed vertebrate genomes.

  15. On the Hydraulics of Flowing Horizontal Wells

    Science.gov (United States)

    Bian, A.; Zhan, H.

    2003-12-01

    A flowing horizontal well is a special type of horizontal well that does not have pumping/injecting facility. The discharge rate of a flowing horizontal well is controlled by the hydraulic gradient between the aquifer and the well and it generally varies with time if the hydraulic head of the aquifer is transient. This type of well has been used in landslide control, mining dewatering, water table control, underground water transportation through a horizontal tunnel, agricultural water drainage, and other applications. Flowing horizontal wells have quite different hydrodynamic characteristics from horizontal wells with fixed pumping or injecting rates because their discharge rates are functions of the aquifer hydraulic heads (Zhan et al, 2001; Zhan and Zlotnik, 2002). Hydraulics of flowing horizontal wells have rarely been studied although the hydraulics of flowing vertical wells have been extensively investigated before. The purpose of this paper is to obtain analytical solutions of groundwater flow to a flowing horizontal-well in a confined aquifer, in a water table aquifer without precipitation, and in a water table aquifer with precipitation. The functions of the flowing horizontal well discharge rates versus time will be obtained under above mentioned different aquifer conditions. The relationships of the aquifer hydraulic heads versus the discharge rates of the well will be investigated. The rate of water table decline due to the dewatering of the well will also be computed, and this solution is particularly useful for landslide control and mining dewatering. The theoretical solutions will be compared with results of experiments that will be conducted in the hydrological laboratory at Texas A&M University. Reference: Zhan, H., Wang, L.V., and Park, E, On the horizontal well pumping tests in the anisotropic confined aquifers, J. hydrol., 252, 37-50, 2001. Zhan, H., and Zlotnik, V. A., Groundwater flow to a horizontal or slanted well in an unconfined aquifer

  16. Lexicographic Path Induction

    DEFF Research Database (Denmark)

    Schürmann, Carsten; Sarnat, Jeffrey

    2009-01-01

    Programming languages theory is full of problems that reduce to proving the consistency of a logic, such as the normalization of typed lambda-calculi, the decidability of equality in type theory, equivalence testing of traces in security, etc. Although the principle of transfinite induction...... an induction principle that combines the comfort of structural induction with the expressive strength of transfinite induction. Using lexicographic path induction, we give a consistency proof of Martin-Löf’s intuitionistic theory of inductive definitions. The consistency of Heyting arithmetic follows directly...

  17. JAVA PathFinder

    Science.gov (United States)

    Mehhtz, Peter

    2005-01-01

    JPF is an explicit state software model checker for Java bytecode. Today, JPF is a swiss army knife for all sort of runtime based verification purposes. This basically means JPF is a Java virtual machine that executes your program not just once (like a normal VM), but theoretically in all possible ways, checking for property violations like deadlocks or unhandled exceptions along all potential execution paths. If it finds an error, JPF reports the whole execution that leads to it. Unlike a normal debugger, JPF keeps track of every step how it got to the defect.

  18. Rocket Flight Path

    Directory of Open Access Journals (Sweden)

    Jamie Waters

    2014-09-01

    Full Text Available This project uses Newton’s Second Law of Motion, Euler’s method, basic physics, and basic calculus to model the flight path of a rocket. From this, one can find the height and velocity at any point from launch to the maximum altitude, or apogee. This can then be compared to the actual values to see if the method of estimation is a plausible. The rocket used for this project is modeled after Bullistic-1 which was launched by the Society of Aeronautics and Rocketry at the University of South Florida.

  19. Path Through the Wheat

    Directory of Open Access Journals (Sweden)

    David Middleton

    2005-01-01

    Full Text Available The hillside’s tidal waves of yellow-green Break downward into full-grown stalks of wheat In which a peasant, shouldering his hoe Passes along a snaking narrow path -- A teeming place through which his hard thighs press And where his head just barely stays above The swaying grain, drunken in abundance, Farm buildings almost floating on the swells Beyond which sea gulls gliding white in air Fly down on out of sight to salty fields, Taking the channel fish off Normandy, A surfeit fit for Eden i...

  20. Horizontal Directional Drilling (HDD) Technology and Applications

    Institute of Scientific and Technical Information of China (English)

    J. G. Cai; X. N. Wang

    2004-01-01

    @@ 1 What is Horizontal Directional Drilling? Horizontal Directional Drilling, accurately steered drilling, has become state -of- the -art drilling technique in the world. Specially- designed directionsteerable corebarrel and accurate direction measurement tool are available for the use together with wire line core drilling machine. That makes it feasible to extract cores and to measure the drill travel line &length while drilling in a curve.

  1. Intra-firm Horizontal Knowledge Transfer Management

    Institute of Scientific and Technical Information of China (English)

    WANG Yaowu; WANG Yanhang

    2009-01-01

    Knowledge transfer is widely emphasized as a strategic issue for firm competition. A model for intra-firm horizontal knowledge transfer is proposed to model horizontal knowledge transfer to solve some demerits in current knowledge transfer researches. The concept model of intra-firm horizontal knowledge transfer was described and a framework was provided to define the main components of thetransfer process. Horizontal knowledge transfer is that knowledge is transferred from the source to the same hierarchical level recipients as the target. Horizontal knowledge transfer constitutes a strategic area of knowledge management research. However, little is known about the circumstances under which one particular mechanism is the most appropriate. To address these issues, some significant conclusions are drawn concerning knowledge transfer mechanisms in a real-world setting.

  2. Horizontal Canal Benign Positional Vertigo

    Directory of Open Access Journals (Sweden)

    Mohtaram Najafi

    1998-03-01

    Full Text Available Benign paroxysmal positional vertigo (BPPV is a syndrome characterized by transient episodes of vertigo in association with rapid changes in head position in Dix-Halpike Maneuver. This kind of vertigo is thought to be caused by migration of otoconial debris into canals other than the posterior canal, such as the anterior or lateral canals. It is also theoretically possible for many aberrant patterns of BPPV to occur from an interaction of debris in several canals, location of debris within the canal, and central adaptation patterns to lesions. The symptoms of BPPV are much more consistent with free-moving densities (canaliths in the posterior SCC rather than fixed densities attached to the cupula. While the head is upright, the particles sit in the PSC at the most gravity-dependent position. The best method to induce and see vertigo and nystagmus in BPPV of the lateral semicircular canal is to rotate head 90°while patient is in the supine position, nystagmus would appear in the unaffected side weaker but longer than the affected side. canal paresis has been described in one third of the patients with BPPV. Adaptation which is one of the remarkable features of BPPV in PSC is rarely seen in LSC. Rotations of 270° or 360° around the yaw axis (the so-called barbecue maneuver toward the unaffected ear are popular methods for the treatment of geotropic HC-BPPV. These maneuvers consist of sequential head turning of 90° toward the healthy side while supine. With these maneuvers, the free-floating otoconial debris migrates in the ampullofugal direction, finally entering the utricle through the nonampullated end of the horizontal canal. This kind of vertigo recovers spontaneously more rapidly and suddenly.

  3. Study on weld formation in a novel rotating arc horizontal GMAW

    Institute of Scientific and Technical Information of China (English)

    Guo Ning; Lin Sanbao; Fan Chenglei; Zhang Yaqi; Yang Chunli

    2009-01-01

    A novel rotating arc horizontal welding process was developed for solving the sagging of the molten pool which bottlenecks the application and the development of the horizontal welding. The principle of the effect of the rotating arc on the molten pool is that the rotating arc process not only can reduce the welding heat input by prolonging the welding path in the same welding distance caused by the arc rotation, but also disperse the arc force to affect the sidewall periodically to support the molten metal near the upper sidewall. The effects of the rotating speed and arc voltage on the weld formation were studied.The results indicate that there is an appropriate range of the rotating speed and the arc voltage to obtain the defect free horizontal welding.

  4. Experimental verification of effect of horizontal inhomogeneity of evaporation duct on electromagnetic wave propagation

    Institute of Scientific and Technical Information of China (English)

    史阳; 杨坤德; 杨益新; 马远良

    2015-01-01

    The evaporation duct which forms above the ocean surface has a significant influence on electromagnetic wave prop-agation above 2 GHz over the ocean. The effects of horizontal inhomogeneity of evaporation duct on electromagnetic wave propagation are investigated, both in numerical simulation and experimental observation methods, in this paper. Firstly, the features of the horizontal inhomogeneity of the evaporation duct are discussed. Then, two typical inhomogeneous cases are simulated and compared with the homogeneous case. The result shows that path loss is significantly higher than that in the homogeneous case when the evaporation duct height (EDH) at the receiver is lower than that at the transmitter. It is also concluded that the horizontal inhomogeneity of the evaporation duct has a significant influence when the EDH is low or when the electromagnetic wave frequency is lower than 13 GHz. Finally, experimental data collected on a 149-km long propagation path in the South China Sea in 2013 are used to verify the conclusion. The experimental results are consis-tent with the simulation results. The horizontal inhomogeneity of evaporation duct should be considered when modeling electromagnetic wave propagation over the ocean.

  5. Comparison of Visibility Measurements over Horizontal Path by Micro-pulsed Lidar and Visibility Meter

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    As a powerful tool to scan the atmosphere, the 1idar can derive visibility values by directly collecting the backscattering laser light from the atmosphere. Simultaneous measurements of atmospheric visibility by Micro-pulsed lidar (MPL) and a commercial visibility meter (VM) NQ-1 have been performed to evaluate the feasibility of the MPL system designed by the Ocean Remote Sensing Laboratory (ORSL) of the Ocean University of China (OUC) from October 21 2005 to November 21 2005 in the Shilaoren Sightseeing Garden on the Qingdao coast. All the 880 data samples obtained by the two instruments have high correlation coefficients (up to 0.86), which indicates it is feasible to utilize MPL to measure atmospheric visibility.

  6. Path Integrals in Quantum Physics

    CERN Document Server

    Rosenfelder, R

    2012-01-01

    These lectures aim at giving graduate students an introduction to and a working knowledge of path integral methods in a wide variety of fields in physics. Consequently, the lecture notes are organized in three main parts dealing with non-relativistic quantum mechanics, many-body physics and field theory. In the first part the basic concepts of path integrals are developed in the usual heuristic, non-mathematical way followed by standard examples and special applications including numerical evaluation of (euclidean) path integrals by Monte-Carlo methods with a program for the anharmonic oscillator. The second part deals with the application of path integrals in statistical mechanics and many-body problems treating the polaron problem, dissipative quantum systems, path integrals over ordinary and Grassmannian coherent states and perturbation theory for both bosons and fermions. Again a simple Fortran program is included for illustrating the use of strong-coupling methods. Finally, in the third part path integra...

  7. Shortest Paths and Vehicle Routing

    DEFF Research Database (Denmark)

    Petersen, Bjørn

    This thesis presents how to parallelize a shortest path labeling algorithm. It is shown how to handle Chvátal-Gomory rank-1 cuts in a column generation context. A Branch-and-Cut algorithm is given for the Elementary Shortest Paths Problem with Capacity Constraint. A reformulation of the Vehicle R...... Routing Problem based on partial paths is presented. Finally, a practical application of finding shortest paths in the telecommunication industry is shown.......This thesis presents how to parallelize a shortest path labeling algorithm. It is shown how to handle Chvátal-Gomory rank-1 cuts in a column generation context. A Branch-and-Cut algorithm is given for the Elementary Shortest Paths Problem with Capacity Constraint. A reformulation of the Vehicle...

  8. Path integrals for awkward actions

    CERN Document Server

    Amdahl, David

    2016-01-01

    Time derivatives of scalar fields occur quadratically in textbook actions. A simple Legendre transformation turns the lagrangian into a hamiltonian that is quadratic in the momenta. The path integral over the momenta is gaussian. Mean values of operators are euclidian path integrals of their classical counterparts with positive weight functions. Monte Carlo simulations can estimate such mean values. This familiar framework falls apart when the time derivatives do not occur quadratically. The Legendre transformation becomes difficult or so intractable that one can't find the hamiltonian. Even if one finds the hamiltonian, it usually is so complicated that one can't path-integrate over the momenta and get a euclidian path integral with a positive weight function. Monte Carlo simulations don't work when the weight function assumes negative or complex values. This paper solves both problems. It shows how to make path integrals without knowing the hamiltonian. It also shows how to estimate complex path integrals b...

  9. Entanglement by Path Identity

    CERN Document Server

    Krenn, Mario; Lahiri, Mayukh; Zeilinger, Anton

    2016-01-01

    Quantum entanglement is one of the most prominent features of quantum mechanics and forms the basis of quantum information technologies. Here we present a novel method for the creation of quantum entanglement in multipartite and high-dimensional photonic systems, exploiting an idea introduced by the group of Leonard Mandel 25 years ago. The two ingredients are 1) superposition of photon pairs with different origins and 2) aligning photon paths such that they emerge from the same output mode. We explain examples for the creation of various classes of multiphoton entanglement encoded in polarization as well as in high-dimensional Hilbert spaces -- starting only from separable (non-entangled) photon pairs. For two photons, we show how arbitrary high-dimensional entanglement can be created. Interestingly, a common source for two-photon polarization entanglement is found as a special case. We discovered the technique by analyzing the output of a computer algorithm designing quantum experiments, and generalized it ...

  10. innovation path exploration

    Directory of Open Access Journals (Sweden)

    Li Jian

    2016-01-01

    Full Text Available The world has entered the information age, all kinds of information technologies such as cloud technology, big data technology are in rapid development, and the “Internet plus” appeared. The main purpose of “Internet plus” is to provide an opportunity for the further development of the enterprise, the enterprise technology, business and other aspects of factors combine. For enterprises, grasp the “Internet plus” the impact of the market economy will undoubtedly pave the way for the future development of enterprises. This paper will be on the innovation path of the enterprise management “Internet plus” era tied you study, hope to be able to put forward some opinions and suggestions.

  11. Propagators and path integrals

    Energy Technology Data Exchange (ETDEWEB)

    Holten, J.W. van

    1995-08-22

    Path-integral expressions for one-particle propagators in scalar and fermionic field theories are derived, for arbitrary mass. This establishes a direct connection between field theory and specific classical point-particle models. The role of world-line reparametrization invariance of the classical action and the implementation of the corresponding BRST-symmetry in the quantum theory are discussed. The presence of classical world-line supersymmetry is shown to lead to an unwanted doubling of states for massive spin-1/2 particles. The origin of this phenomenon is traced to a `hidden` topological fermionic excitation. A different formulation of the pseudo-classical mechanics using a bosonic representation of {gamma}{sub 5} is shown to remove these extra states at the expense of losing manifest supersymmetry. (orig.).

  12. Study of the Logistics Enterprise Development Path based on Niche Theory

    Institute of Scientific and Technical Information of China (English)

    Sun Wenxia

    2013-01-01

    This paper refers evolutionary ecology of niche theory,analyzes logistics enterprises niche,as well as niche overlapping,niche separation,niche compression,niche expansionetc.And on this basis,this paper proposes,the development path of the logistics enterprise “co-operation,with in the horizontal,external vertical cooperation”,hoping advancing further of logisticsenterprises.

  13. Path integral in Snyder space

    Energy Technology Data Exchange (ETDEWEB)

    Mignemi, S., E-mail: smignemi@unica.it [Dipartimento di Matematica e Informatica, Università di Cagliari, Viale Merello 92, 09123 Cagliari (Italy); INFN, Sezione di Cagliari, Cittadella Universitaria, 09042 Monserrato (Italy); Štrajn, R. [Dipartimento di Matematica e Informatica, Università di Cagliari, Viale Merello 92, 09123 Cagliari (Italy); INFN, Sezione di Cagliari, Cittadella Universitaria, 09042 Monserrato (Italy)

    2016-04-29

    The definition of path integrals in one- and two-dimensional Snyder space is discussed in detail both in the traditional setting and in the first-order formalism of Faddeev and Jackiw. - Highlights: • The definition of the path integral in Snyder space is discussed using phase space methods. • The same result is obtained in the first-order formalism of Faddeev and Jackiw. • The path integral formulation of the two-dimensional Snyder harmonic oscillator is outlined.

  14. Path indexing for term retrieval

    OpenAIRE

    1992-01-01

    Different methods for term retrieval in deduction systems have been introduced in literature. This report eviews the three indexing techniques discrimination indexing, path indexing, and abstraction tree indexing. A formal approach to path indexing is presented and algorithms as well as data structures of an existing implementation are discussed. Eventually, experiments will show that our implementation outperforms the implementation of path indexing in the OTTER theorem prover.

  15. An introduction to critical paths.

    Science.gov (United States)

    Coffey, Richard J; Richards, Janet S; Remmert, Carl S; LeRoy, Sarah S; Schoville, Rhonda R; Baldwin, Phyllis J

    2005-01-01

    A critical path defines the optimal sequencing and timing of interventions by physicians, nurses, and other staff for a particular diagnosis or procedure. Critical paths are developed through collaborative efforts of physicians, nurses, pharmacists, and others to improve the quality and value of patient care. They are designed to minimize delays and resource utilization and to maximize quality of care. Critical paths have been shown to reduce variation in the care provided, facilitate expected outcomes, reduce delays, reduce length of stay, and improve cost-effectiveness. The approach and goals of critical paths are consistent with those of total quality management (TQM) and can be an important part of an organization's TQM process.

  16. Optimizing of Culture Conditionin Horizontal Rotating Bioreactor

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    1 IntroductionBioreactor is the most important equipment in tissue engineering. It can mimic the micro-environment of cell growth in vitro. At present, horizontal rotating bioreactor is the most advanced equipment for cell culture in the world. 2 Rotating bioreactors2.1 Working principleThere are two kinds of horizontal rotating bioreactor: HARV(high aspect ratio vessel) and RCCS (rotary cell culture system). It is drived by step motor with horizontal rotation, the culture medium and cell is filled between ...

  17. Horizontal gene transfer and bacterial diversity

    Indian Academy of Sciences (India)

    Chitra Dutta; Archana Pan

    2002-02-01

    Bacterial genomes are extremely dynamic and mosaic in nature. A substantial amount of genetic information is inserted into or deleted from such genomes through the process of horizontal transfer. Through the introduction of novel physiological traits from distantly related organisms, horizontal gene transfer often causes drastic changes in the ecological and pathogenic character of bacterial species and thereby promotes microbial diversification and speciation. This review discusses how the recent influx of complete chromosomal sequences of various microorganisms has allowed for a quantitative assessment of the scope, rate and impact of horizontally transmitted information on microbial evolution.

  18. Horizontal cooperation in transport and logistics

    NARCIS (Netherlands)

    Cruijssen, F.C.A.M.

    2006-01-01

    This thesis deals with horizontal cooperation in transport and logistics. It contains a comprehensive discussion of the available academic literature on this topic, many practical examples, and an empirical investigation of opportunities and impediments. Furthermore, three enabling concepts for

  19. Chromatic roots and hamiltonian paths

    DEFF Research Database (Denmark)

    Thomassen, Carsten

    2000-01-01

    We present a new connection between colorings and hamiltonian paths: If the chromatic polynomial of a graph has a noninteger root less than or equal to t(n) = 2/3 + 1/3 (3)root (26 + 6 root (33)) + 1/3 (3)root (26 - 6 root (33)) = 1.29559.... then the graph has no hamiltonian path. This result...

  20. Two Generations of Path Dependence

    DEFF Research Database (Denmark)

    Madsen, Mogens Ove

      Even if there is no fully articulated and generally accepted theory of Path Dependence it has eagerly been taken up across a wide range of social sciences - primarily coming from economics. Path Dependence is most of all a metaphor that offers reason to believe, that some political, social...

  1. Evaluation of extremely small horizontal emittance

    Directory of Open Access Journals (Sweden)

    T. Okugi

    1999-02-01

    Full Text Available The KEK Accelerator Test Facility (KEK-ATF was constructed to develop technologies for producing a low-emittance beam which will be required by future linear colliders. The KEK-ATF consists of an injector linac, a damping ring, and a beam extraction line. The basic optical structure of the damping ring is a FOBO lattice, which reduces the horizontal dispersion at the center of the bending magnets and, as a consequence, can produce an extremely small emittance beam. To verify the performance of such a unique, low-emittance lattice, it is crucial to measure the horizontal emittance. The horizontal emittance was measured using wire scanners in the beam extraction line. Since the horizontal beam position was not stable, we established a method to correct the measured beam size for position fluctuation (“jitter” and we succeeded in the observation of the so far smallest horizontal emittance in any accelerator. The measured horizontal emittance was 1.37±0.03nm at a beam energy of 1.285 GeV and a bunch population of \\(3–5\\×10^{9}, in agreement with the design value of 1.27–1.34 nm at the beam energy and the bunch population.

  2. Sustainable Energy Path

    Directory of Open Access Journals (Sweden)

    Hiromi Yamamoto

    2005-12-01

    Full Text Available The uses of fossil fuels cause not only the resources exhaustion but also the environmental problems such as global warming. The purposes of this study are to evaluate paths toward sustainable energy systems and roles of each renewable. In order to realize the purposes, the authors developed the global land use and energy model that figured the global energy supply systems in the future considering the cost minimization. Using the model, the authors conducted a simulation in C30R scenario, which is a kind of strict CO2 emission limit scenarios and reduced CO2 emissions by 30% compared with Kyoto protocol forever scenario, and obtained the following results. In C30R scenario bioenergy will supply 33% of all the primary energy consumption. However, wind and photovoltaic will supply 1.8% and 1.4% of all the primary energy consumption, respectively, because of the limits of power grid stability. The results imply that the strict limits of CO2 emissions are not sufficient to achieve the complete renewable energy systems. In order to use wind and photovoltaic as major energy resources, we need not only to reduce the plant costs but also to develop unconventional renewable technologies.

  3. Hard paths, soft paths or no paths? Cross-cultural perceptions of water solutions

    Science.gov (United States)

    Wutich, A.; White, A. C.; White, D. D.; Larson, K. L.; Brewis, A.; Roberts, C.

    2014-01-01

    In this study, we examine how development status and water scarcity shape people's perceptions of "hard path" and "soft path" water solutions. Based on ethnographic research conducted in four semi-rural/peri-urban sites (in Bolivia, Fiji, New Zealand, and the US), we use content analysis to conduct statistical and thematic comparisons of interview data. Our results indicate clear differences associated with development status and, to a lesser extent, water scarcity. People in the two less developed sites were more likely to suggest hard path solutions, less likely to suggest soft path solutions, and more likely to see no path to solutions than people in the more developed sites. Thematically, people in the two less developed sites envisioned solutions that involve small-scale water infrastructure and decentralized, community-based solutions, while people in the more developed sites envisioned solutions that involve large-scale infrastructure and centralized, regulatory water solutions. People in the two water-scarce sites were less likely to suggest soft path solutions and more likely to see no path to solutions (but no more likely to suggest hard path solutions) than people in the water-rich sites. Thematically, people in the two water-rich sites seemed to perceive a wider array of unrealized potential soft path solutions than those in the water-scarce sites. On balance, our findings are encouraging in that they indicate that people are receptive to soft path solutions in a range of sites, even those with limited financial or water resources. Our research points to the need for more studies that investigate the social feasibility of soft path water solutions, particularly in sites with significant financial and natural resource constraints.

  4. H∞ control for path tracking of autonomous underwater vehicle motion

    Directory of Open Access Journals (Sweden)

    Lin-Lin Wang

    2015-05-01

    Full Text Available In order to simplify the design of path tracking controller and solve the problem relating to nonlinear dynamic model of autonomous underwater vehicle motion planning, feedback linearization method is first adopted to transform the nonlinear dynamic model into an equivalent pseudo-linear dynamic model in horizontal coordinates. Then considering wave disturbance effect, mixed-sensitivity method of H∞ robust control is applied to design state-feedback controller for this equivalent dynamic model. Finally, control law of pseudo-linear dynamic model is transformed into state (surge velocity and yaw angular rate tracking control law of nonlinear dynamic model through inverse coordinate transformation. Simulation indicates that autonomous underwater vehicle path tracking is successfully implemented with this proposed method, and the influence of parameter variation in autonomous underwater vehicle dynamic model on its tracking performance is reduced by H∞ controller. All the results show that the method proposed in this article is effective and feasible.

  5. Horizontal roof gap of backfill hydraulic support

    Institute of Scientific and Technical Information of China (English)

    张强; 张吉雄; 邰阳; 方坤; 殷伟

    2015-01-01

    For the backfill hydraulic support as the key equipment for achieving integration of backfilling and coal mining simultaneously in the practical process, its characteristics will directly influence the backfill body’s compression ratio. Horizontal roof gap, as a key parameter of backfilling characteristics, may impact the backfilling effect from the aspects of control of roof subsidence in advance, support stress, backfilling process and the support design. Firstly, the reason why horizontal roof gap exists was analyzed and its definition, causes and connotation were introduced, then adopting the Pro/E 3D simulation software, three typical 3D entity models of backfill hydraulic supports were built, based on the influence of horizontal roof gap on backfilling effect, and influence rules of four factors, i.e. support height, suspension height, suspension angle and tamping angle, were emphatically analyzed on horizontal roof gap. The results indicate that, the four factors all have significant impacts on horizontal roof gap, but show differences in influence trend and degree, showing negative linear correlation, positive linear correlation, positive semi-parabolic correlation and negative semi-parabolic correlation, respectively. Four legs type is the most adaptive to the four factors, while six legs (II) type has the poorest adaptability, and the horizontal roof gap is small under large support height, small suspension height, small suspension angle and large tamping angle situation. By means of optimizing structure components and their positional relation and suspension height of backfill scrape conveyor in the process of support design and through controlling working face deployment, roof subsidence in advance, mining height and backfilling during engineering application, the horizontal roof gap is optimized. The research results can be served as theoretical basis for support design and guidance for backfill support to have better performance in backfilling.

  6. 14 CFR 23.57 - Takeoff path.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff path. 23.57 Section 23.57... path. For each commuter category airplane, the takeoff path is as follows: (a) The takeoff path extends... completed; and (1) The takeoff path must be based on the procedures prescribed in § 23.45; (2) The...

  7. Geodesic flows on path spaces

    Institute of Scientific and Technical Information of China (English)

    XIANG; Kainan

    2001-01-01

    [1] Cruzeiro, A. B., Malliavin, P., Renormalized differential geometry on path spaces: Structural equation, curvature, J. Funct. Anal., 1996, 139: 119-181.[2] Stroock, D. W., Some thoughts about Riemannian structures on path spaces, preprint, 1996.[3] Driver, B., A Cameron-Martin type quasi-invariance theorem for Brownian motion on a compact manifold, J. Funct. Anal., 1992, 109: 272-376.[4] Enchev, O., Stroock, D. W., Towards a Riemannian geometry on the path space over a Riemannian manifold, J. Funct. Anal., 1995, 134: 392-416.[5] Hsu, E., Quasi-invariance of the Wiener measure on the path space over a compact Riemannian manifold, J. Funct. Anal., 1995, 134: 417-450.[6] Lyons, T. J., Qian, Z. M., A class of vector fields on path space, J.Funct. Anal., 1997, 145: 205-223.[7] Li, X. D., Existence and uniqueness of geodesics on path spaces, J. Funct. Anal., to be published.[8] Driver, B., Towards calculus and geometry on path spaces, in Proc. Symp. Pure and Appl. Math. 57 (ed. Cranston, M., Pinsky, M.), Cornell: AMS, 1993, 1995.

  8. Path integrals and quantum processes

    CERN Document Server

    Swanson, Marc S

    1992-01-01

    In a clearly written and systematic presentation, Path Integrals and Quantum Processes covers all concepts necessary to understand the path integral approach to calculating transition elements, partition functions, and source functionals. The book, which assumes only a familiarity with quantum mechanics, is ideal for use as a supplemental textbook in quantum mechanics and quantum field theory courses. Graduate and post-graduate students who are unfamiliar with the path integral will also benefit from this contemporary text. Exercise sets are interspersed throughout the text to facilitate self-

  9. Path Integration in Conical Space

    OpenAIRE

    Inomata, Akira; Junker, Georg

    2011-01-01

    Quantum mechanics in conical space is studied by the path integral method. It is shown that the curvature effect gives rise to an effective potential in the radial path integral. It is further shown that the radial path integral in conical space can be reduced to a form identical with that in flat space when the discrete angular momentum of each partial wave is replaced by a specific non-integral angular momentum. The effective potential is found proportional to the squared mean curvature of ...

  10. On the Reaction Path Hamiltonian

    Institute of Scientific and Technical Information of China (English)

    孙家钟; 李泽生

    1994-01-01

    A vector-fiber bundle structure of the reaction path Hamiltonian, which has been introduced by Miller, Handy and Adams, is explored with respect to molecular vibrations orthogonal to the reaction path. The symmetry of the fiber bundle is characterized by the real orthogonal group O(3N- 7) for the dynamical system with N atoms. Under the action of group O(3N- 7). the kinetic energy of the reaction path Hamiltonian is left invariant. Furthermore , the invariant behaviour of the Hamiltonian vector fields is investigated.

  11. Paths and wakes of deformable nearly spheroidal rising bubbles close to the transition to path instability

    Science.gov (United States)

    Cano-Lozano, José Carlos; Martínez-Bazán, Carlos; Magnaudet, Jacques; Tchoufag, Joël

    2016-09-01

    We report on a series of results provided by three-dimensional numerical simulations of nearly spheroidal bubbles freely rising and deforming in a still liquid in the regime close to the transition to path instability. These results improve upon those of recent computational studies [Cano-Lozano et al., Int. J. Multiphase Flow 51, 11 (2013), 10.1016/j.ijmultiphaseflow.2012.11.005; Phys. Fluids 28, 014102 (2016), 10.1063/1.4939703] in which the neutral curve associated with this transition was obtained by considering realistic but frozen bubble shapes. Depending on the dimensionless parameters that characterize the system, various paths geometries are observed by letting an initially spherical bubble starting from rest rise under the effect of buoyancy and adjust its shape to the surrounding flow. These include the well-documented rectilinear axisymmetric, planar zigzagging, and spiraling (or helical) regimes. A flattened spiraling regime that most often eventually turns into either a planar zigzagging or a helical regime is also frequently observed. Finally, a chaotic regime in which the bubble experiences small horizontal displacements (typically one order of magnitude smaller than in the other regimes) is found to take place in a region of the parameter space where no standing eddy exists at the back of the bubble. The discovery of this regime provides evidence that path instability does not always result from a wake instability as previously believed. In each regime, we examine the characteristics of the path, bubble shape, and vortical structure in the wake, as well as their couplings. In particular, we observe that, depending on the fluctuations of the rise velocity, two different vortex shedding modes exist in the zigzagging regime, confirming earlier findings with falling spheres. The simulations also reveal that significant bubble deformations may take place along zigzagging or spiraling paths and that, under certain circumstances, they dramatically alter

  12. Horizontal alveolar bone loss: A periodontal orphan

    Directory of Open Access Journals (Sweden)

    Jayakumar A

    2010-01-01

    Full Text Available Background: Attempts to successfully regenerate lost alveolar bone have always been a clinician′s dream. Angular defects, at least, have a fairer chance, but the same cannot be said about horizontal bone loss. The purpose of the present study was to evaluate the prevalence of horizontal alveolar bone loss and vertical bone defects in periodontal patients; and later, to correlate it with the treatment modalities available in the literature for horizontal and vertical bone defects. Materials and Methods: The study was conducted in two parts. Part I was the radiographic evaluation of 150 orthopantomographs (OPGs (of patients diagnosed with chronic periodontitis and seeking periodontal care, which were digitized and read using the AutoCAD 2006 software. All the periodontitis-affected teeth were categorized as teeth with vertical defects (if the defect angle was ≤45° and defect depth was ≥3 mm or as having horizontal bone loss. Part II of the study comprised search of the literature on treatment modalities for horizontal and vertical bone loss in four selected periodontal journals. Results: Out of the 150 OPGs studied, 54 (36% OPGs showed one or more vertical defects. Totally, 3,371 teeth were studied, out of which horizontal bone loss was found in 3,107 (92.2% teeth, and vertical defects were found only in 264 (7.8% of the teeth, which was statistically significant (P<.001. Search of the selected journals revealed 477 papers have addressed the treatment modalities for vertical and horizontal types of bone loss specifically. Out of the 477 papers, 461 (96.3% have addressed vertical bone loss, and 18 (3.7% have addressed treatment options for horizontal bone loss. Two papers have addressed both types of bone loss and are included in both categories. Conclusion: Horizontal bone loss is more prevalent than vertical bone loss but has been sidelined by researchers as very few papers have been published on the subject of regenerative treatment

  13. Transition Path Theory

    Science.gov (United States)

    vanden-Eijnden, E.

    The dynamical behavior of many systems arising in physics, chemistry, biology, etc. is dominated by rare but important transition events between long lived states. For over 70 years, transition state theory (TST) has provided the main theoretical framework for the description of these events [17,33,34]. Yet, while TST and evolutions thereof based on the reactive flux formalism [1, 5] (see also [30,31]) give an accurate estimate of the transition rate of a reaction, at least in principle, the theory tells very little in terms of the mechanism of this reaction. Recent advances, such as transition path sampling (TPS) of Bolhuis, Chandler, Dellago, and Geissler [3, 7] or the action method of Elber [15, 16], may seem to go beyond TST in that respect: these techniques allow indeed to sample the ensemble of reactive trajectories, i.e. the trajectories by which the reaction occurs. And yet, the reactive trajectories may again be rather uninformative about the mechanism of the reaction. This may sound paradoxical at first: what more than actual reactive trajectories could one need to understand a reaction? The problem, however, is that the reactive trajectories by themselves give only a very indirect information about the statistical properties of these trajectories. This is similar to why statistical mechanics is not simply a footnote in books about classical mechanics. What is the probability density that a trajectory be at a given location in state-space conditional on it being reactive? What is the probability current of these reactive trajectories? What is their rate of appearance? These are the questions of interest and they are not easy to answer directly from the ensemble of reactive trajectories. The right framework to tackle these questions also goes beyond standard equilibrium statistical mechanics because of the nontrivial bias that the very definition of the reactive trajectories imply - they must be involved in a reaction. The aim of this chapter is to

  14. Walking paths to and from a goal differ: on the role of bearing angle in the formation of human locomotion paths.

    Directory of Open Access Journals (Sweden)

    Manish Sreenivasa

    Full Text Available The path that humans take while walking to a goal is the result of a cognitive process modulated by the perception of the environment and physiological constraints. The path shape and timing implicitly embeds aspects of the architecture behind this process. Here, locomotion paths were investigated during a simple task of walking to and from a goal, by looking at the evolution of the position of the human on a horizontal (x,y plane. We found that the path while walking to a goal was not the same as that while returning from it. Forward-return paths were systematically separated by 0.5-1.9m, or about 5% of the goal distance. We show that this path separation occurs as a consequence of anticipating the desired body orientation at the goal while keeping the target in view. The magnitude of this separation was strongly influenced by the bearing angle (difference between body orientation and angle to goal and the final orientation imposed at the goal. This phenomenon highlights the impact of a trade-off between a directional perceptual apparatus-eyes in the head on the shoulders-and and physiological limitations, in the formation of human locomotion paths. Our results give an insight into the influence of environmental and perceptual variables on human locomotion and provide a basis for further mathematical study of these mechanisms.

  15. Environmental Measurement-While-Drilling System and Horizontal Directional Drilling Technology Demonstration, Hanford Site

    Energy Technology Data Exchange (ETDEWEB)

    Williams, C.V.; Lockwood, G.J.; Normann, R.A.; Myers, D.A.; Gardner, M.G.; Williamson, T.; Huffman, J.

    1999-06-01

    The Environmental Measurement-While-Drilling (EMWD) system and Horizontal Directional Drilling (HDD) were successfully demonstrated at the Mock Tank Leak Simulation Site and the Drilling Technology Test Site, Hanford, Washington. The use of directional drilling offers an alternative to vertical drilling site characterization. Directional drilling can develop a borehole under a structure, such as a waste tank, from an angled entry and leveling off to horizontal at the desired depth. The EMWD system represents an innovative blend of new and existing technology that provides the capability of producing real-time environmental and drill bit data during drilling operations. The technology demonstration consisted of the development of one borehole under a mock waste tank at a depth of {approximately} {minus}8 m ({minus}27 ft.), following a predetermined drill path, tracking the drill path to within a radius of {approximately}1.5 m (5 ft.), and monitoring for zones of radiological activity using the EMWD system. The purpose of the second borehole was to demonstrate the capability of drilling to a depth of {approximately} {minus}21 m ({minus}70 ft.), the depth needed to obtain access under the Hanford waste tanks, and continue drilling horizontally. This report presents information on the HDD and EMWD technologies, demonstration design, results of the demonstrations, and lessons learned.

  16. Scattering theory with path integrals

    Energy Technology Data Exchange (ETDEWEB)

    Rosenfelder, R. [Particle Theory Group, Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland)

    2014-03-15

    Starting from well-known expressions for the T-matrix and its derivative in standard nonrelativistic potential scattering, I rederive recent path-integral formulations due to Efimov and Barbashov et al. Some new relations follow immediately.

  17. Scattering Theory with Path Integrals

    CERN Document Server

    Rosenfelder, R

    2013-01-01

    Starting from well-known expressions for the $T$-matrix and its derivative in standard nonrelativistic potential scattering I rederive recent path-integral formulations due to Efimov and Barbashov et al. Some new relations follow immediately.

  18. The Internet's unexploited path diversity

    CERN Document Server

    Arjona-Villicaña, Pedro David; Stepanenko, Alexander S

    2009-01-01

    The connectivity of the Internet at the Autonomous System level is influenced by the network operator policies implemented. These in turn impose a direction to the announcement of address advertisements and, consequently, to the paths that can be used to reach back such destinations. We propose to use directed graphs to properly represent how destinations propagate through the Internet and the number of arc-disjoint paths to quantify this network's path diversity. Moreover, in order to understand the effects that policies have on the connectivity of the Internet, numerical analyses of the resulting directed graphs were conducted. Results demonstrate that, even after policies have been applied, there is still path diversity which the Border Gateway Protocol cannot currently exploit.

  19. An Introduction to Path Analysis

    Science.gov (United States)

    Wolfe, Lee M.

    1977-01-01

    The analytical procedure of path analysis is described in terms of its use in nonexperimental settings in the social sciences. The description assumes a moderate statistical background on the part of the reader. (JKS)

  20. Diffuser Augmented Horizontal Axis Tidal Current Turbines

    Directory of Open Access Journals (Sweden)

    Nasir Mehmood

    2012-09-01

    Full Text Available The renewal energy technologies are increasingly popular to ensure future energy sustenance and address environmental issues. The tides are enormous and consistent untapped resource of renewable energy. The growing interest in exploring tidal energy has compelling reasons such as security and diversity of supply, intermittent but predictable and limited social and environmental impacts. The tidal energy industry is undergoing an increasing shift towards diffuser augmented turbines. The reason is the higher power output of diffuser augmented turbines compared to conventional open turbines. The purpose of this study is to present a comprehensive review of diffuser augmented horizontal axis tidal current turbines. The components, relative advantages, limitations and design parameters of diffuser augmented horizontal axis tidal current turbines are presented in detail. CFD simulation of NACA 0016 airfoil is carried out to explore its potential for designing a diffuser. The core issues associated with diffuser augmented horizontal axis tidal current turbines are also discussed.

  1. HORIZONTAL WELL DRILL-IN FLUIDS

    Directory of Open Access Journals (Sweden)

    Nediljka Gaurina-Međimurec

    1998-12-01

    Full Text Available Main objective of horizontal driling is to place a drain-hole for a long distance within the pay zone to enhance productivity or injectivity. In drilling horizontal wells, more serious problems appear than in drilling vertical wells. These problems are: poor hole cleaning, excessive torque and drag, hole filling, pipe stucking, wellbore instability, loss of circulation, formation damage, poor cement job, and difficulties at logging jobs. From that reason, successful drilling and production of horizontal well depends largely on the fluid used during drilling and completion phases. Several new fluids, that fulfill some or all of required properties (hole cleaning, cutting suspension, good lubrication, and relative low formation damage, are presented in this paper.

  2. Horizontal stirring in the global ocean

    CERN Document Server

    Hernández-Carrasco, I; Hernández-García, E; Turiel, A

    2011-01-01

    Horizontal mixing and the distribution of coherent structures in the global ocean are analyzed using Finite-Size Lyapunov Exponents (FSLE), computed for the surface velocity field derived from the Ocean general circulation model For the Earth Simulator (OFES). FSLEs measure horizontal stirring and dispersion; additionally, the transport barriers which organize the oceanic flow can roughly be identified with the ridges of the FSLE field. We have performed a detailed statistical study, particularizing for the behaviour of the two hemispheres and different ocean basins. The computed Probability Distributions Functions (PDFs) of FSLE are broad and asymmetric. Horizontal mixing is generally more active in the northern hemisphere than in the southern one. Nevertheless the Southern Ocean is the most active ocean, and the Pacific the less active one. A striking result is that the main currents can be classified in two 'activity classes': Western Boundary Currents, which have broad PDFs with large FSLE values, and Eas...

  3. Effects of T-type Channel on Natural Convection Flows in Airflow-Path of Concrete Storage Cask

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Gyeong Uk; Kim, Hyoung Jin; Cho, Chun Hyung [KORAD, Daejeon (Korea, Republic of)

    2016-05-15

    The natural convection flows occurring in airflow-path are not simple due to complex flow-path configurations such as horizontal ducts, bent tube and annular flow-path. In addition, 16 T type channels acting as the shroud are attached vertically and 16 channel supporting the canister are attached horizontally on the inner surface of over-pack. The existence and nonexistence of T type channels have influences on the flow fields in airflow- path. The concrete storage cask has to satisfy the requirements to secure the thermal integrity under the normal, off-normal, and accident conditions. The present work is aiming at investigating the effects of T type channels on the flows in airflow-path under the normal conditions using the FLUENT 16.1 code. In order to focus on the flows in airflow-path, fuel regions in the canister are regarded as a single cylinder with heat sources and other components are fully modeled. This study investigated the flow fields in airflow-path of concrete storage cask, numerically. It was found that excepting for the fuel regions, maximum temperatures on other components were evaluated below allowable values. The location of maximum velocities depended on support channels, T type channels and flow area. The flows through air inlets developed along annular flow- path with forming the hot plumes. According to the existence and nonexistence of T type channel, the plume behavior showed the different flow patterns.

  4. Equivariant Localization of Path Integrals

    OpenAIRE

    Szabo, Richard J.

    1996-01-01

    We review equivariant localization techniques for the evaluation of Feynman path integrals. We develop systematic geometric methods for studying the semi-classical properties of phase space path integrals for dynamical systems, emphasizing the relations with integrable and topological quantum field theories. Beginning with a detailed review of the relevant mathematical background -- equivariant cohomology and the Duistermaat-Heckman theorem, we demonstrate how the localization ideas are relat...

  5. Path Integrals in Quantum Physics

    OpenAIRE

    2012-01-01

    These lectures aim at giving graduate students an introduction to and a working knowledge of path integral methods in a wide variety of fields in physics. Consequently, the lecture notes are organized in three main parts dealing with non-relativistic quantum mechanics, many-body physics and field theory. In the first part the basic concepts of path integrals are developed in the usual heuristic, non-mathematical way followed by standard examples and special applications including numerical ev...

  6. Formal language constrained path problems

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, C.; Jacob, R.; Marathe, M.

    1997-07-08

    In many path finding problems arising in practice, certain patterns of edge/vertex labels in the labeled graph being traversed are allowed/preferred, while others are disallowed. Motivated by such applications as intermodal transportation planning, the authors investigate the complexity of finding feasible paths in a labeled network, where the mode choice for each traveler is specified by a formal language. The main contributions of this paper include the following: (1) the authors show that the problem of finding a shortest path between a source and destination for a traveler whose mode choice is specified as a context free language is solvable efficiently in polynomial time, when the mode choice is specified as a regular language they provide algorithms with improved space and time bounds; (2) in contrast, they show that the problem of finding simple paths between a source and a given destination is NP-hard, even when restricted to very simple regular expressions and/or very simple graphs; (3) for the class of treewidth bounded graphs, they show that (i) the problem of finding a regular language constrained simple path between source and a destination is solvable in polynomial time and (ii) the extension to finding context free language constrained simple paths is NP-complete. Several extensions of these results are presented in the context of finding shortest paths with additional constraints. These results significantly extend the results in [MW95]. As a corollary of the results, they obtain a polynomial time algorithm for the BEST k-SIMILAR PATH problem studied in [SJB97]. The previous best algorithm was given by [SJB97] and takes exponential time in the worst case.

  7. El horizonte estético

    OpenAIRE

    Perniola, Mario

    2004-01-01

    La existencia de un horizonte estético depende de la coexistencia de múltiples factores de distinta naturaleza que interactúan entre ellos. No bastan las reflexiones en torno a lo bello y al arte para crear un horizonte estético. La palabra “estética” es introducida en el Settecento por la filosofía para indicar una articulación disciplinar propia que pudiera ubicarse cerca de la lógica; esta circunstancia histórica, sin embargo, no debe hacernos olvidar que la filosofía es desde su nacimient...

  8. Fourth international seminar on horizontal steam generators

    Energy Technology Data Exchange (ETDEWEB)

    Tuomisto, H. [ed.] [IVO Group, Vantaa (Finland); Purhonen, H. [ed.] [VTT, Espoo (Finland); Kouhia, V. [ed.] [Lappeenranta Univ. of Technology (Finland)

    1997-12-31

    The general objective of the International Seminars of Horizontal Steam Generator Modelling has been the improvement in understanding of realistic thermal hydraulic behaviour of the generators when performing safety analyses for VVER reactors. The main topics presented in the fourth seminar were: thermal hydraulic experiments and analyses, primary collector integrity, feedwater distributor replacement, management of primary-to-secondary leakage accidents and new developments in the VVER safety technology. The number of participants, representing designers and manufacturers of the horizontal steam generators, plant operators, engineering companies, research organizations, universities and regulatory authorities, was 70 from 10 countries.

  9. Horizontal Roll Vortices and Crown Fires.

    Science.gov (United States)

    Haines, Donald A.

    1982-06-01

    Observational evidence from nine crown fires suggests that horizontal roll vortices are a major mechanism in crown-fire spread. Post-burn aerial photography indicates that unburned tree-crown streets are common with crown fire. Investigation of the understory of these crown streets after two fires showed uncharred tree trunks along a center line. This evidence supports a hypothesis of vortex action causing strong downward motion of air along the streets. Additionally, photographs of two ongoing crown fires show apparent horizontal roll vortices. Discussion also includes laboratory and numerical studies in fluid dynamics that may apply to crown fires.

  10. Asteroidal Quadruples in non Rooted Path Graphs

    Directory of Open Access Journals (Sweden)

    Gutierrez Marisa

    2015-11-01

    Full Text Available A directed path graph is the intersection graph of a family of directed subpaths of a directed tree. A rooted path graph is the intersection graph of a family of directed subpaths of a rooted tree. Rooted path graphs are directed path graphs. Several characterizations are known for directed path graphs: one by forbidden induced subgraphs and one by forbidden asteroids. It is an open problem to find such characterizations for rooted path graphs. For this purpose, we are studying in this paper directed path graphs that are non rooted path graphs. We prove that such graphs always contain an asteroidal quadruple.

  11. Horizontal single-trip gravel pack and selective simulation system for deep water extended reach wells

    Energy Technology Data Exchange (ETDEWEB)

    Pineda, Francisco [BJ Services Company, Houston, TX (United States); Vilela, Alvaro; Montanha, Roberto; Acosta, Marco; Farias, Rodrigo [BJ Services do Brasil Ltda., Rio de Janeiro, RJ (Brazil)

    2004-07-01

    Most of the reservoirs located in the deep water and ultra-deep water offshore South America are described as unconsolidated sandstone that require sand control on both producers and water injection wells. Horizontal Open Hole Gravel Pack completions are the preferred method of development. If completing heavy oil reservoirs, there is a necessity of longer horizontal open hole sections. Low fracture gradients may limit the length of gravel pack in the open hole section because of the pressure increase during the Beta wave proppant deposition phase. This system allows the gravel pack assembly to be installed and the gravel pack to be pumped during the alpha and beta wave deposition phases without the limitation of high pressures that could fracture the well. The benefits of the Horizontal Single-Trip Gravel Pack and Selective Stimulation System (HSTSSS) using the differential valve include the ability to complete longer horizontal intervals, valuable rig-time savings and, efficient mechanical diversion of the stimulation fluid. This paper outlines the application of the HSTSSS system using a differential valve to complete a horizontal well in offshore deep waters. The need for a differential valve is primarily in horizontal gravel packing operations when normal circulating rates and pressures around the open hole would exceed formation break down pressure. The valve is intended to be easily spaced out and run in the wash pipe. At a predetermined differential pressure the valve opens and the return flow path distance around the bottom of the tailpipe is shortened, thus reducing back pressure preventing filter cake damage without slowing the pump rate. In addition the said valve has to close to allow the selective stimulation to take place. Economic considerations along with completion efficiencies are especially important on deep water, subsea completions. The utilization of differential valves allows completion of extended-reach open hole wells and/or low fracture

  12. Anomalous paths in quantum mechanical path-integrals

    Energy Technology Data Exchange (ETDEWEB)

    Grimsmo, Arne L., E-mail: arne.grimsmo@ntnu.no [Department of Physics, The Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Department of Physics, The University of Auckland, Private Bag 92019, Auckland (New Zealand); Klauder, John R., E-mail: klauder@phys.ufl.edu [Departments of Physics and Mathematics, University of Florida, Gainesville, FL 32611 (United States); Skagerstam, Bo-Sture K., E-mail: bo-sture.skagerstam@ntnu.no [Department of Physics, The Norwegian University of Science and Technology, N-7491 Trondheim (Norway); Kavli Institute for Theoretical Physics, Kohn Hall, University of California at Santa Barbara, CA 93106-4030 (United States); CREOL, The College of Optics and Photonics at the University of Central Florida, 4000 Central Florida Boulevard, Orlando, FL 32816 (United States)

    2013-11-25

    We investigate modifications of the discrete-time lattice action, for a quantum mechanical particle in one spatial dimension, that vanish in the naïve continuum limit but which, nevertheless, induce non-trivial effects due to quantum fluctuations. These effects are seen to modify the geometry of the paths contributing to the path-integral describing the time evolution of the particle, which we investigate through numerical simulations. In particular, we demonstrate the existence of a modified lattice action resulting in paths with any fractal dimension, d{sub f}, between one and two. We argue that d{sub f}=2 is a critical value, and we exhibit a type of lattice modification where the fluctuations in the position of the particle becomes independent of the time step, in which case the paths are interpreted as superdiffusive Lévy flights. We also consider the jaggedness of the paths, and show that this gives an independent classification of lattice theories.

  13. Path Following Control of A Deep-Sea Manned Submersible Based upon NTSM

    Institute of Scientific and Technical Information of China (English)

    MA Ling; CUI Wei-cheng

    2005-01-01

    In this paper, a robust path following control law is proposed for a deep-sea manned submersible maneuvering along a predeterminated path. Developed in China, the submersible is underactuated in the horizontal plane in that it is actuated by two perpendicular thrusts in this plane. The advanced non-singular terminal sliding mode (NTSM) is implemented for the design of the path following controller, which can ensure the convergence of the motion system in finite time and improve its robustness against parametric uncertainties and environmental disturbances. In the process of controller design, the close-loop stability is considered and proved by Lyapunov's stability theory. With the experimental data, numerical simulations are provided to verify the control law for path following of the deep-sea manned submersible.

  14. A Case Study of Horizontal Teacher Evaluation.

    Science.gov (United States)

    Johnson, Trav D.

    Horizontal teacher evaluation increases understanding of teaching through the critical examination of educational goals and classroom practices. This examination includes teachers' classroom observations of one another coupled with in-depth teacher conversations or dialogue about teaching aims and practices. A qualitative case study of a…

  15. Third international seminar on horizontal steam generators

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The Third International Seminar on Horizontal Steam Generators held on October 18-20, 1994 in Lappeenranta, consisted of six sessions dealing with the topics: thermal hydraulic experiments and analyses, primary collector integrity, management of primary-to-secondary leakage accidents, feedwater collector replacement and discussion of VVER-440 steam generator safety issues.

  16. Parametric study for horizontal steam generator modelling

    Energy Technology Data Exchange (ETDEWEB)

    Ovtcharova, I. [Energoproekt, Sofia (Bulgaria)

    1995-12-31

    In the presentation some of the calculated results of horizontal steam generator PGV - 440 modelling with RELAP5/Mod3 are described. Two nodalization schemes have been used with different components in the steam dome. A study of parameters variation on the steam generator work and calculated results is made in cases with separator and branch.

  17. Evaluation of horizontal magnification on panoramic images

    Directory of Open Access Journals (Sweden)

    Maryam Raoof

    2013-01-01

    Full Text Available Aims: This study evaluated the horizontal magnification of images taken from adults and pediatrics with PM 2002 CC Planmeca analogue machine. Materials and Methods: A series of 120 panoramic radiographs were obtained of 60 adults and 60 pediatrics. For all patients, negative impressions were used to make positive casts of the teeth. A caliper was used to measure the maximum mesiodistal length of the buccal surface of all teeth except canines on both casts and radiographs. The horizontal magnification factor was calculated for incisor, premolar, and molar regions by dividing the values obtained from the casts by the values obtained from the radiographs. Statistical Analysis: Independent t-test and one-way analysis of variance (ANOVA were used. Results: The results indicated that with regard to adults, maxillary and mandibular incisor regions, unlike the other two sessions, didn′t show significant difference of the mean magnification of horizontal dimension (P = 0.5. In pediatrics, the comparison between mean magnification factors of all subgroups showed significant difference (P < 0.0001. Despite the adults′ radiographs, the results of pediatrics′ radiographs showed significantly higher magnification than the index listed by the manufacturer of the radiographic machine used. Conclusion: The present study results point to the fact that PM 2002 CC Proline panoramic machine makes possible precise measurements on radiographs of adults′ jaws in the horizontal dimension.

  18. Fermion mass hierarchy and global horizontal symmetries

    Energy Technology Data Exchange (ETDEWEB)

    Gelmini, G.B.; Gerard, J.M.; Yanagida, T.; Zoupanos, G. (European Organization for Nuclear Research, Geneva (Switzerland))

    1984-02-02

    We present a mechanism for quark mass generation in zeroth order using induced representations rather than the minimization of the horizontal potential. Using a simplicity criterion, we derive a realistic mass matrix. We also discuss a possible application of the mechanism to various models.

  19. Horizontal gene transfer in the phytosphere

    NARCIS (Netherlands)

    Elsas, van J.D.; Turner, S.; Bailey, M.J.

    2003-01-01

    Here, the ecological aspects of gene transfer processes between bacteria in the phytosphere are examined in the context of emerging evidence for the dominant role that horizontal gene transfer (HGT) has played in the evolutionary shaping of bacterial communities. Moreover, the impact of the putative

  20. Flow mapping for ESS horizontal target

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Y.; Kikura, H.; Taishi, T. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-09-01

    Flow behaviour for ESS horizontal target is studied experimentally using two dimensional water model. A velocity field of stationary flow in reaction zone has been obtained. Three dimensional effect was also studied as a spanwise flow structure. (author) 3 figs., 3 refs.

  1. Buoyancy Driven Natural Ventilation through Horizontal Openings

    DEFF Research Database (Denmark)

    Heiselberg, Per

    2009-01-01

    An experimental study of the phenomenon of buoyancy driven natural ventilation through single-sided horizontal openings was performed in a full-scale laboratory test rig. The measurements were made for opening ratios L/D ranging from 0.027 to 4.455, where L and D are the length of the opening...

  2. Teaching Activities on Horizontal Nuclear Proliferation.

    Science.gov (United States)

    Zola, John

    1990-01-01

    Provides learning activities concerning the horizontal proliferation of nuclear weapons. Includes step-by-step directions for four activities: (1) the life cycle of nuclear weapons; (2) nuclear nonproliferation: pros and cons; (3) the nuclear power/nuclear weapons connection; and (4) managing nuclear proliferation. (NL)

  3. Mud and cement for horizontal wells

    Energy Technology Data Exchange (ETDEWEB)

    Zurdo, C.; Georges, C.; Martin, M.

    1986-01-01

    High-angle and horizontal well bores raise many questions concerning the characteristics of mud and cement. This paper is a summary of the authors' knowledge and work on these two subjects. For all research carried out, large or full-scale laboratory test plants were used. Cutting transport is not only a problem in horizontal conditions but hole angles of 25 to 65/sup 0/ can be even more critical when parameters such as mud rheological properties and velocities are not optimized. Drilling a long horizontal drain creates a dynamic annulus pressure unbalance. This can lead to a loss and kick situation. Two test benches were thus used to obtain a good understanding of the inefficiency of conventional plugging methods and of the difficulties of gas migration control in subhorizontal well bores. High concentrations of LCM, high rheological properties of fluids and low flow rates increase the changes of solving the first problem. The results of the second bench demonstrate the difficulties of annulus gas evacution for angles varying from 90 to 100 degrees, or from over-gauged sections in horizontal holes.

  4. Verification of the adiabatic invariant approximation for computing effective horizontal sound speeds in a range dependent environment

    Science.gov (United States)

    Northrop, J.; Shockley, R. C.; Hansen, P. G.

    1980-09-01

    Use of the Adiabatic Invariant Approximation (AIA) for determining horizontal sound speeds in a range dependent environment was proposed. Because the method provides a great savings in computer time over conventional ray tracing techniques, it was applied to two very-long-range paths, from Perth, Australia, to Bermuda and to Fernando de Noronha (19763.0 and 14549.3 km, respectively), where measured travel times are available. Results show that the AIA method predicts effective horizontal sound speeds of 1482.3m/s and 1480.4m/s, respectively, for the two propagation paths. These results compare favorably with the measured values of 1484.7 - or - 3.7 m/s and 1480.1 + or - 0.9 m/s.

  5. Discrete Coherent State Path Integrals

    Science.gov (United States)

    Marchioro, Thomas L., II

    1990-01-01

    The quantum theory provides a fundamental understanding of the physical world; however, as the number of degrees of freedom rises, the information required to specify quantum wavefunctions grows geometrically. Because basis set expansions mirror this geometric growth, a strict practical limit on quantum mechanics as a numerical tool arises, specifically, three degrees of freedom or fewer. Recent progress has been made utilizing Feynman's Path Integral formalism to bypass this geometric growth and instead calculate time -dependent correlation functions directly. The solution of the Schrodinger equation is converted into a large dimensional (formally infinite) integration, which can then be attacked with Monte Carlo techniques. To date, work in this area has concentrated on developing sophisticated mathematical algorithms for evaluating the highly oscillatory integrands occurring in Feynman Path Integrals. In an alternative approach, this work demonstrates two formulations of quantum dynamics for which the number of mathematical operations does not scale geometrically. Both methods utilize the Coherent State basis of quantum mechanics. First, a localized coherent state basis set expansion and an approximate short time propagator are developed. Iterations of the short time propagator lead to the full quantum dynamics if the coherent state basis is sufficiently dense along the classical phase space path of the system. Second, the coherent state path integral is examined in detail. For a common class of Hamiltonians, H = p^2/2 + V( x) the path integral is reformulated from a phase space-like expression into one depending on (q,dot q). It is demonstrated that this new path integral expression contains localized damping terms which can serve as a statistical weight for Monte Carlo evaluation of the integral--a process which scales approximately linearly with the number of degrees of freedom. Corrections to the traditional coherent state path integral, inspired by a

  6. BER of flat-topped Gaussian beam in slant path turbulent atmosphere

    Science.gov (United States)

    Lu, Fang; Han, Yanyan; Han, Xiang-e.; Yang, Rui-ke

    2013-08-01

    Based on the theory of optical wave propagation in the slant path and the ITU-R turbulence structure constant model which is dependent on altitude, the on-axis scintillation index of the flat-topped Gaussian beam at the receiver plane in slant path turbulence was given by using Kolmogorov atmospheric turbulence power spectrum model. The influences of the link altitudes, atmospheric refractive index structure constant C0 at the ground,the source size and the beam order on scintillation index of the flat-topped Gaussian beam are discussed in detail. The result shows that the scintillation index increased first and then decreased with the increase of the beam order. The advantage of a flat-topped Gaussian beam over a single Gaussian beam is restricted to small source sizes, which is consistent with the case of the horizontal path. To find the average bit error rate under weak slant path turbulence, the log-normal distribution model of the intensity fluctuation was used. The influence of beam order and source size on BER was discussed. The result indicates that the smaller sized flat-topped Gaussian beam will bring average bit error rate advantage over the same size Gaussian beam. Our results correctly reduce to the result of the horizontal path with atmospheric structure constant fixed.

  7. New sufficient conditions for Hamiltonian paths.

    Science.gov (United States)

    Rahman, M Sohel; Kaykobad, M; Firoz, Jesun Sahariar

    2014-01-01

    A Hamiltonian path in a graph is a path involving all the vertices of the graph. In this paper, we revisit the famous Hamiltonian path problem and present new sufficient conditions for the existence of a Hamiltonian path in a graph.

  8. Population Monotonic Path Schemes for Simple Games

    NARCIS (Netherlands)

    Ciftci, B.B.; Borm, P.E.M.; Hamers, H.J.M.

    2006-01-01

    A path scheme for a simple game is composed of a path, i.e., a sequence of coalitions that is formed during the coalition formation process and a scheme, i.e., a payoff vector for each coalition in the path.A path scheme is called population monotonic if a player's payoff does not decrease as the pa

  9. Gas-path seal technology

    Science.gov (United States)

    Zuk, J.

    1976-01-01

    Improved gas-path seals are needed for better fuel economy, longer performance retention, and lower maintenance, particularly in advanced, high-performance gas turbine engines. Problems encountered in gas-path sealing are described, as well as new blade-tip sealing approaches for high-pressure compressors and turbines. These include a lubricant coating for conventional, porous-metal, rub-strip materials used in compressors. An improved hot-press metal alloy shows promise to increase the operating surface temperatures of high-pressure-turbine, blade-tip seals to 1450 K (2150 F). Three ceramic seal materials are also described that have the potential to allow much higher gas-path surface operating temperatures than are possible with metal systems.

  10. Rainbow paths with prescribed ends

    DEFF Research Database (Denmark)

    Alishahi, Meysam; Taherkhani, Ali; Thomassen, Carsten

    2011-01-01

    It was conjectured in [S. Akbari, F. Khaghanpoor, and S. Moazzeni. Colorful paths in vertex coloring of graphs. Preprint] that, if G is a connected graph distinct from C-7, then there is a chi(G)-coloring of G in which every vertex v is an element of V(G) is an initial vertex of a path P with chi......(G) vertices whose colors are different. In[S. Akbari, V. Liaghat, and A. Nikzad. Colorful paths in vertex coloring of graphs. Electron. J. Combin. 18(1):P17, 9pp, 2011] this was proved with left perpendicular chi(G)/2right perpendicular vertices instead of chi(G) vertices. We strengthen this to chi(G) - 1...

  11. Construction, Installation, and Results from a Seafloor Horizontal Optical Fiber Strainmeter

    Science.gov (United States)

    Zumberge, M. A.; Hatfield, W.; Elliott, D.; Agnew, D. C.; Wyatt, F. K.

    2016-12-01

    In October 2015 we deployed a 200-m horizontal optical fiber strainmeter on the seafloor 93 km west of the Oregon coastline, at 1900 m depth and on the toe of the accretionary prism of the Cascadia Subduction Zone. We used the ROV Jason to install and tension the sensing fiber between two 100 kg anchors; new signal processing electronics with a small form factor and low power consumption allowed 96 days of continuous operation. The strainmeter used two fibers with different refractivity temperature coefficients; recording the optical path length of both fibers allows us to separate path length changes caused by temperature from actual strain. Drift in the strainmeter of 90 nanostrain per day resulted from imperfect coupling between the anchors and deeper, more consolidated sediment. A clear correlation between ocean tide height and strain suggests laterally varying structure within the accretionary prism.

  12. Innovative development path of ethnomedicines: the interpretation of the path.

    Science.gov (United States)

    Zhu, Zhaoyun; Fu, Dehuan; Gui, Yali; Cui, Tao; Wang, Jingkun; Wang, Ting; Yang, Zhizhong; Niu, Yanfei; She, Zhennan; Wang, Li

    2017-03-01

    One of the primary purposes of the innovative development of ethnomedicines is to use their excellent safety and significant efficacy to serve a broader population. To achieve this purpose, modern scientific and technological means should be referenced, and relevant national laws and regulations as well as technical guides should be strictly followed to develop standards and to perform systemic research in producing ethnomedicines. Finally, ethnomedicines, which are applied to a limited extent in ethnic areas, can be transformed into safe, effective, and quality-controllable medical products to relieve the pain of more patients. The innovative development path of ethnomedicines includes the following three primary stages: resource study, standardized development research, and industrialization of the achievements and efforts for internationalization. The implementation of this path is always guaranteed by the research and development platform and the talent team. This article is based on the accumulation of long-term practice and is combined with the relevant disciplines, laws and regulations, and technical guidance from the research and development of ethnomedicines. The intention is to perform an in-depth analysis and explanation of the major research thinking, methods, contents, and technical paths involved in all stages of the innovative development path of ethnomedicines to provide useful references for the development of proper ethnomedicine use.

  13. Path Decomposition of Graphs with Given Path Length

    Institute of Scientific and Technical Information of China (English)

    Ming-qing Zhai; Chang-hong Lü

    2006-01-01

    A path decomposition of a graph G is a list of paths such that each edge appears in exactly one path in the list. G is said to admit a {Pl}-decomposition if G can be decomposed into some copies of Pl, where Pl is a path of length ι - 1. Similarly, G is said to admit a {Pl, Pκ}-decomposition if G can be decomposed into some copies of Pl or Pκ. An κ-cycle, denoted by Cκ, is a cycle with κ vertices. An odd tree is a tree of which all vertices have odd degree. In this paper, it is shown that a connected graph G admits a {P3, P4}-decomposition if and only if G is neither a 3-cycle nor an odd tree. This result includes the related result of Yan, Xu and Mutu. Moreover, two polynomial algorithms are given to find {P3}-decomposition and {P3, P4}-decomposition of graphs, respectively. Hence, {P3}-decomposition problem and {P3, P4}-decomposition problem of graphs are solved completely.

  14. Spin Observables and Path Integrals

    CERN Document Server

    López, J A

    2000-01-01

    We discuss the formulation of spin observables associated to a non-relativistic spinning particles in terms of grassmanian differential operators. We use as configuration space variables for the pseudo-classical description of this system the positions $x$ and a Grassmanian vector quantum amplitudes as path integrals in this superspace. We compute the quantum action necessary for this description including an explicit expression for the boundary terms. Finally we shown how for simple examples, the path integral may be performed in the semi-classical approximation, leading to the correct quantum propagator.

  15. Paths of algebraic hyperbolic curves

    Institute of Scientific and Technical Information of China (English)

    Ya-juan LI; Li-zheng LU; Guo-zhao WANG

    2008-01-01

    Cubic algebraic hyperbolic (AH) Bezier curves and AH spline curves are defined with a positive parameter α in the space spanned by {1, t, sinht, cosht}. Modifying the value of α yields a family of AH Bezier or spline curves with the family parameter α. For a fixed point on the original curve, it will move on a defined curve called "path of AH curve" (AH Bezier and AH spline curves) when α changes. We describe the geometric effects of the paths and give a method to specify a curve passing through a given point.

  16. Strings, paths, and standard tableaux

    CERN Document Server

    Dasmahapatra, S

    1996-01-01

    For the vacuum sectors of regime-III ABF models, we observe that two sets of combinatorial objects: the strings which parametrize the row-to-row transfer matrix eigenvectors, and the paths which parametrize the corner transfer matrix eigenvectors, can both be expressed in terms of the same set of standard tableaux. Furthermore, the momenta of the strings, the energies of the paths, and the charges of the tableaux are such that there is a weight-preserving bijection between the two sets of eigenvectors, wherein the tableaux play an interpolating role. This bijection is so natural, that we conjecture that it exists in general.

  17. Characteristics of Buoyancy Driven Natural Ventilation through Horizontal Openings

    DEFF Research Database (Denmark)

    Li, Zhigang

    and smoke. Air flow through vertical openings has been widely investigated but little is known about the flow in the horizontal openings, especially when they are driven by buoyancy. A literature survey shows that the brine-water system and the scale model are normally used forthe research work of air flow...... through horizontal openings. Two cases of full-scale measurements of buoyancy driven natural ventilation through horizontal openings are performed: one horizontal opening and one horizontal opening combined with one vertical opening. For the case of one horizontal opening, the measurements are made...

  18. The horizontal plane appearances of scoliosis

    DEFF Research Database (Denmark)

    Illés, Tamás S.; Burkus, Máté; Somoskeőy, Szabolcs

    2017-01-01

    Purpose: A posterior-anterior vertebral vector is proposed to facilitate visualization and understanding of scoliosis. The aim of this study was to highlight the interest of using vertebral vectors, especially in the horizontal plane, in clinical practice. Methods: We used an EOS two-/three-dimen......Purpose: A posterior-anterior vertebral vector is proposed to facilitate visualization and understanding of scoliosis. The aim of this study was to highlight the interest of using vertebral vectors, especially in the horizontal plane, in clinical practice. Methods: We used an EOS two...... of scoliosis. The approach used is simple. These results are sufficient for a first visual analysis furnishing significant clinical information in all three anatomical planes. This visualization represents a reasonable compromise between mathematical purity and practical use....

  19. Kinematics of horizontal and vertical caterpillar crawling.

    Science.gov (United States)

    van Griethuijsen, Linnea I; Trimmer, Barry A

    2009-05-01

    Unlike horizontal crawling, vertical crawling involves two counteracting forces: torque rotating the body around its center of mass and gravity resisting forward movement. The influence of these forces on kinematics has been examined in the soft-bodied larval stage of Manduca sexta. We found that crawling and climbing are accomplished using the same movements, with both segment timing and proleg lift indistinguishable in horizontal and vertical locomotion. Minor differences were detected in stride length and in the delay between crawls, which led to a lower crawling speed in the vertical orientation. Although these differences were statistically significant, they were much smaller than the variation in kinematic parameters between animals. The ability of Manduca to crawl and climb using the same movements is best explained by Manduca's relatively small size, slow speed and strong, controlled, passive grip made possible by its proleg/crochets.

  20. Detecting series periodicity with horizontal visibility graphs

    CERN Document Server

    Núñez, Angel M; Valero, Eusebio; Gómez, Jose Patricio; Luque, Bartolo

    2011-01-01

    The horizontal visibility algorithm has been recently introduced as a mapping between time series and networks. The challenge lies in characterizing the structure of time series (and the processes that generated those series) using the powerful tools of graph theory. Recent works have shown that the visibility graphs inherit several degrees of correlations from their associated series, and therefore such graph theoretical characterization is in principle possible. However, both the mathematical grounding of this promising theory and its applications are on its infancy. Following this line, here we address the question of detecting hidden periodicity in series polluted with a certain amount of noise. We first put forward some generic properties of horizontal visibility graphs which allow us to define a (graph theoretical) noise reduction filter. Accordingly, we evaluate its performance for the task of calculating the period of noisy periodic signals, and compare our results with standard time domain (autocorre...

  1. Buoyancy Driven Natural Ventilation through Horizontal Openings

    DEFF Research Database (Denmark)

    Heiselberg, Per; Li, Zhigang

    2009-01-01

    An experimental study of the phenomenon of buoyancy driven natural ventilation through single-sided horizontal openings was performed in a full-scale laboratory test rig. The measurements were made for opening ratios L/D ranging from 0.027 to 4.455, where L and D are the length of the opening...... and the diameter of the opening, respectively. The basic nature of airflow through single-sided openings, including airflow rate, air velocity, temperature difference between the rooms and the dimensions of the horizontal openings, were measured. A bi-directional airflow rate was measured using the constant...... injection tracer gas technique. Smoke visualizations showed that the airflow patterns are highly transient and unstable, and that the airflow rate oscillates with time. Correlations between the Froude (Archimedes) number Fr (Ar) and the L/D ratio are presented. In some cases the measured airflow rates fit...

  2. Horizontal Bilayer for Electrical and Optical Recordings

    Directory of Open Access Journals (Sweden)

    Alf Honigmann

    2012-12-01

    Full Text Available Artificial bilayer containing reconstituted ion channels, transporters and pumps serve as a well-defined model system for electrophysiological investigations of membrane protein structure–function relationship. Appropriately constructed microchips containing horizontally oriented bilayers with easy solution access to both sides provide, in addition, the possibility to investigate these model bilayer membranes and the membrane proteins therein with high resolution fluorescence techniques up to the single-molecule level. Here, we describe a bilayer microchip system in which long-term stable horizontal free-standing and hydrogel-supported bilayers can be formed and demonstrate its prospects particularly for single-molecule fluorescence spectroscopy and high resolution fluorescence microscopy in probing the physicochemical properties like phase behavior of the bilayer-forming lipids, as well as in functional studies of membrane proteins.

  3. Gas reservoir evaluation for underbalanced horizontal drilling

    Directory of Open Access Journals (Sweden)

    Li Gao

    2014-01-01

    Full Text Available A set of surface equipment for monitoring the parameters of fluid and pressure while drilling was developed, and mathematical models for gas reservoir seepage and wellbore two-phase flow were established. Based on drilling operation parameters, well structure and monitored parameters, the wellbore pressure and the gas reservoir permeability could be predicted theoretically for underbalanced horizontal drilling. Based on the monitored gas production along the well depth, the gas reservoir type could be identified.

  4. Horizontal Symmetry: Bottom Up and Top Down

    CERN Document Server

    Lam, C S

    2011-01-01

    A group-theoretical connection between horizontal symmetry $\\G$ and fermion mixing is established, and applied to neutrino mixing. The group-theoretical approach is consistent with a dynamical theory based on $U(1)\\times \\G$, but the dynamical theory can be used to pick out the most stable mixing that purely group-theoretical considerations cannot. A symmetry common to leptons and quarks is also discussed. This higher symmetry picks $A_4$ over $S_4$ to be the preferred symmetry for leptons.

  5. Convection in horizontally shaken granular material

    OpenAIRE

    Saluena, Clara; Poeschel, Thorsten

    1998-01-01

    In horizontally shaken granular material different types of pattern formation have been reported. We want to deal with the convection instability which has been observed in experiments and which recently has been investigated numerically. Using two dimensional molecular dynamics we show that the convection pattern depends crucial on the inelastic properties of the material. The concept of restitution coefficient provides arguments for the change of the behaviour with variing inelasticity.

  6. R&D investments fostering horizontal mergers

    OpenAIRE

    Cabolis, C.; Manasakis, C.; MORENO, Diego; Petrakis, Emmanuel

    2016-01-01

    We study a homogenous good triopoly in which firms first choose their cost-reducing R&D investments and consider alternative merger proposals, and then compete à la Cournot in the ensuing industry. We identify conditions under which both horizontal mergers and non integration are sustained by Coalition-Proof Nash equilibria (CPNE). These conditions involve the effectiveness of the R&D technology, as well as the distribution of the bargaining power between the acquirer and the acquiree, which ...

  7. Thermal transient analysis applied to horizontal wells

    Energy Technology Data Exchange (ETDEWEB)

    Duong, A.N. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[ConocoPhillips Canada Resources Corp., Calgary, AB (Canada)

    2008-10-15

    Steam assisted gravity drainage (SAGD) is a thermal recovery process used to recover bitumen and heavy oil. This paper presented a newly developed model to estimate cooling time and formation thermal diffusivity by using a thermal transient analysis along the horizontal wellbore under a steam heating process. This radial conduction heating model provides information on the heat influx distribution along a horizontal wellbore or elongated steam chamber, and is therefore important for determining the effectiveness of the heating process in the start-up phase in SAGD. Net heat flux estimation in the target formation during start-up can be difficult to measure because of uncertainties regarding heat loss in the vertical section; steam quality along the horizontal segment; distribution of steam along the wellbore; operational conditions; and additional effects of convection heating. The newly presented model can be considered analogous to pressure transient analysis of a buildup after a constant pressure drawdown. The model is based on an assumption of an infinite-acting system. This paper also proposed a new concept of a heating ring to measure the heat storage in the heated bitumen at the time of testing. Field observations were used to demonstrate how the model can be used to save heat energy, conserve steam and enhance bitumen recovery. 18 refs., 14 figs., 2 appendices.

  8. Vertical and horizontal seismometric observations of tides

    Science.gov (United States)

    Lambotte, S.; Rivera, L.; Hinderer, J.

    2006-01-01

    Tidal signals have been largely studied with gravimeters, strainmeters and tiltmeters, but can also be retrieved from digital records of the output of long-period seismometers, such as STS-1, particularly if they are properly isolated. Horizontal components are often noisier than the vertical ones, due to sensitivity to tilt at long periods. Hence, horizontal components are often disturbed by local effects such as topography, geology and cavity effects, which imply a strain-tilt coupling. We use series of data (duration larger than 1 month) from several permanent broadband seismological stations to examine these disturbances. We search a minimal set of observable signals (tilts, horizontal and vertical displacements, strains, gravity) necessary to reconstruct the seismological record. Such analysis gives a set of coefficients (per component for each studied station), which are stable over years and then can be used systematically to correct data from these disturbances without needing heavy numerical computation. A special attention is devoted to ocean loading for stations close to oceans (e.g. Matsushiro station in Japon (MAJO)), and to pressure correction when barometric data are available. Interesting observations are made for vertical seismometric components; in particular, we found a pressure admittance between pressure and data 10 times larger than for gravimeters for periods larger than 1 day, while this admittance reaches the usual value of -3.5 nm/s 2/mbar for periods below 3 h. This observation may be due to instrumental noise, but the exact mechanism is not yet understood.

  9. On the path to differentiation

    DEFF Research Database (Denmark)

    Martinsen, Dorte Sindbjerg; Uygur, Ayca

    2014-01-01

    by examining the ‘path to differentiation’ within EU working time regulation as it has unfolded over time. It identifies the ‘opt-out’ as a means of differentiation adopted to overcome policy deadlocks within collective decision-making, albeit one with unforeseen consequences. In particular, the contribution...

  10. Career Paths in Environmental Sciences

    Science.gov (United States)

    Career paths, current and future, in the environmental sciences will be discussed, based on experiences and observations during the author's 40 + years in the field. An emphasis will be placed on the need for integrated, transdisciplinary systems thinking approaches toward achie...

  11. Geodesic flows on path spaces

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    On the path space over a compact Riemannian manifold, the global existence and the global uniqueness of the quasi-invariant geodesic flows with respect to a negative Markov connection are obtained in this paper. The results answer affirmatively a left problem of Li.

  12. Path integral for inflationary perturbations

    NARCIS (Netherlands)

    Prokopec, T.; Rigopoulos, G.

    2010-01-01

    The quantum theory of cosmological perturbations in single-field inflation is formulated in terms of a path integral. Starting from a canonical formulation, we show how the free propagators can be obtained from the well-known gauge-invariant quadratic action for scalar and tensor perturbations, and

  13. Methodologies for tracking learning paths

    DEFF Research Database (Denmark)

    Frølunde, Lisbeth; Gilje, Øystein; Lindstrand, Fredrik

    2009-01-01

    The article concerns the design of a collaborative research project (2008-09) entitled Making a Filmmaker, which examines how young Scandinavian filmmakers create their own learn- ing paths in formal and/or informal contexts. Our interest is how learning experiences and contexts motivate the young...

  14. Determinants of weighted path matrices

    CERN Document Server

    Talaska, Kelli

    2012-01-01

    We find rational expressions for all minors of the weighted path matrix of a directed graph, generalizing the classical Lindstrom/Gessel-Viennot result for acyclic directed graphs. The formulas are given in terms of certain flows in the graph.

  15. Optimal paths as correlated random walks

    Science.gov (United States)

    Perlsman, E.; Havlin, S.

    2006-01-01

    A numerical study of optimal paths in the directed polymer model shows that the paths are similar to correlated random walks. It is shown that when a directed optimal path of length t is divided into 3 segments whose length is t/3, the correlation between the transversal movements along the first and last path segments is independent of the path length t. It is also shown that the transversal correlations along optimal paths decrease as the paths approach their endpoints. The numerical results obtained for optimal paths in 1+4 dimensions are qualitatively similar to those obtained for optimal paths in lower dimensions, and the data supplies a strong numerical indication that 1+4 is not the upper critical dimension of this model, and of the associated KPZ equation.

  16. Genetics Home Reference: horizontal gaze palsy with progressive scoliosis

    Science.gov (United States)

    ... Health Conditions HGPPS horizontal gaze palsy with progressive scoliosis Printable PDF Open All Close All Enable Javascript ... collapse boxes. Description Horizontal gaze palsy with progressive scoliosis ( HGPPS ) is a disorder that affects vision and ...

  17. Study of the Local Horizon. (Spanish Title: Estudio del Horizonte Local.) Estudo do Horizonte Local

    Science.gov (United States)

    Ros, Rosa M.

    2009-12-01

    The study of the horizon is fundamental to easy the first observations of the students at any education center. A simple model, to be developed in each center, allows to easy the study and comprehension of the rudiments of astronomy. The constructed model is presented in turn as a simple equatorial clock, other models (horizontal and vertical) may be constructed starting from it. El estudio del horizonte es fundamental para poder facilitar las primeras observaciones de los alumnos en un centro educativo. Un simple modelo, que debe realizarse para cada centro, nos permite facilitar el estudio y la comprensión de los primeros rudimentos astronómicos. El modelo construido se presenta a su vez como un sencillo modelo de reloj ecuatorial y a partir de él se pueden construir otros modelos (horizontal y vertical). O estudo do horizonte é fundamental para facilitar as primeiras observações dos alunos num centro educativo. Um modelo simples, que deve ser feito para cada centro, permite facilitar o estudo e a compreensão dos primeiros rudimentos astronômicos. O modelo construído apresenta-se, por sua vez, como um modelo simples de relógio equatorial e a partir dele pode-se construir outros modelos (horizontal e vertical)

  18. Application of Horizontal Well Technology to Liaohe Oilfield

    Institute of Scientific and Technical Information of China (English)

    HanYun

    2008-01-01

    @@ Horizontal well technology has become one of the main technologies enabling Liaohe Oilfield to realize stable development. By the end of 2006, 296 horizontal wells of various kinds had been completed in Liaohe Oil Field,273 wells had been put into production, Among uhich 237 were horizontal wells (see Table 1).

  19. YPF uses horizontal reentry to aid thin bed production

    Energy Technology Data Exchange (ETDEWEB)

    Acosta, M.R.; Leiro, F.A.; Sesano, G.S. [Yacimientos Petroliferos Fiscales, La Paz (Bolivia); Hill, D.

    1997-01-01

    Reentry and horizontal drilling/completion techniques have proven themselves useful in exploiting thin beds. A pilot horizontal reentry contracted by Yacimiento Petroliferos Fiscales (YPF) for a marginal well in its Lomita Sur field resulted in decreased water coning and production rates four times greater than expected. Further horizontal reentries in this thin-bed field are planned.

  20. Increasing horizontal resolution in numerical weather prediction and climate simulations: illusion or panacea?

    Science.gov (United States)

    Wedi, Nils P

    2014-06-28

    The steady path of doubling the global horizontal resolution approximately every 8 years in numerical weather prediction (NWP) at the European Centre for Medium Range Weather Forecasts may be substantially altered with emerging novel computing architectures. It coincides with the need to appropriately address and determine forecast uncertainty with increasing resolution, in particular, when convective-scale motions start to be resolved. Blunt increases in the model resolution will quickly become unaffordable and may not lead to improved NWP forecasts. Consequently, there is a need to accordingly adjust proven numerical techniques. An informed decision on the modelling strategy for harnessing exascale, massively parallel computing power thus also requires a deeper understanding of the sensitivity to uncertainty--for each part of the model--and ultimately a deeper understanding of multi-scale interactions in the atmosphere and their numerical realization in ultra-high-resolution NWP and climate simulations. This paper explores opportunities for substantial increases in the forecast efficiency by judicious adjustment of the formal accuracy or relative resolution in the spectral and physical space. One path is to reduce the formal accuracy by which the spectral transforms are computed. The other pathway explores the importance of the ratio used for the horizontal resolution in gridpoint space versus wavenumbers in spectral space. This is relevant for both high-resolution simulations as well as ensemble-based uncertainty estimation. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

  1. Facilitating Description and Selection of Learning Paths: the learning path specification put to the test

    NARCIS (Netherlands)

    Janssen, José

    2008-01-01

    Jansen, J. (2008). Facilitating Description and Selection of Learning Paths: the learning path specification put to the test. Presentation at the Otec Colloquium. April, 2008, Heerlen, The Netherlands.

  2. Facilitating Description and Selection of Learning Paths: the learning path specification put to the test

    NARCIS (Netherlands)

    Janssen, José

    2008-01-01

    Jansen, J. (2008). Facilitating Description and Selection of Learning Paths: the learning path specification put to the test. Presentation at the Otec Colloquium. April, 2008, Heerlen, The Netherlands.

  3. Horizontal distribution of mixed cloud type scene

    Science.gov (United States)

    Guillaume, A.; Kahn, B. H.; Yue, Q.; Wong, S.; Manipon, G.; Hua, H.; Wilson, B. D.; Wang, T.; Fetzer, E. J.

    2016-12-01

    We describe a novel method to uniquely characterize and quantify the scale dependence of mixed cloud scene geometry using cloud type classification reported with the 94GHz CloudSat radar. Only a fraction of all possible combinations of cloud types are observed at any along-track length scale considered. Cloud scenes most frequently contain only one or two cloud types. We show how cloud occurrence depends on the grid cell spatial resolution used to define cloud scenes. A maximum number of observed cloud scenes occur near 100 km with fewer cloud type combinations at smaller and larger scales. We then quantify the cloud lengths along the CloudSat track using both the cloud top classification and the vertical structure of cloud classification separately for each of the nine cloud types defined by CloudSat and for all clouds considered independent of cloud type. While the individual cloud types do not follow a clear power law behavior as a function of horizontal or vertical scale, a robust power law scaling of cloud geometry is observed when cloud type is not considered. The power law scaling exponent of horizontal length is approximated by β ≈ -5/3 over two to three orders of magnitude. The power law scaling exponent of vertical length is approximated by β ≈ -7/3 over two orders of magnitude. These exponents are in agreement with previous studies using numerical models, satellite, and in situ aircraft observations. In particular, the anisotropy in the horizontal and vertical scaling are nearly identical to recent aircraft observations of wind kinetic energy spectra, suggesting the underlying three-dimensional cloud geometry is strongly related to kinetic energy spectra.

  4. Shortest Paths With Side Sensors

    CERN Document Server

    Salaris, Paolo; Bicchi, Antonio

    2011-01-01

    We present a complete characterization of shortest paths to a goal position for a vehicle with unicycle kinematics and a limited range sensor, constantly keeping a given landmark in sight. Previous work on this subject studied the optimal paths in case of a frontal, symmetrically limited Field--Of--View (FOV). In this paper we provide a generalization to the case of arbitrary FOVs, including the case that the direction of motion is not an axis of symmetry for the FOV, and even that it is not contained in the FOV. The provided solution is of particular relevance to applications using side-scanning, such as e.g. in underwater sonar-based surveying and navigation.

  5. Stochastic control with rough paths

    Energy Technology Data Exchange (ETDEWEB)

    Diehl, Joscha [University of California San Diego (United States); Friz, Peter K., E-mail: friz@math.tu-berlin.de [TU & WIAS Berlin (Germany); Gassiat, Paul [CEREMADE, Université Paris-Dauphine, PSL Research University (France)

    2017-04-15

    We study a class of controlled differential equations driven by rough paths (or rough path realizations of Brownian motion) in the sense of Lyons. It is shown that the value function satisfies a HJB type equation; we also establish a form of the Pontryagin maximum principle. Deterministic problems of this type arise in the duality theory for controlled diffusion processes and typically involve anticipating stochastic analysis. We make the link to old work of Davis and Burstein (Stoch Stoch Rep 40:203–256, 1992) and then prove a continuous-time generalization of Roger’s duality formula [SIAM J Control Optim 46:1116–1132, 2007]. The generic case of controlled volatility is seen to give trivial duality bounds, and explains the focus in Burstein–Davis’ (and this) work on controlled drift. Our study of controlled rough differential equations also relates to work of Mazliak and Nourdin (Stoch Dyn 08:23, 2008).

  6. Variation in terminology: capoeira in Belo Horizonte

    Directory of Open Access Journals (Sweden)

    César Nardelli Cambraia

    2014-12-01

    Full Text Available In this pilot study we analyzed the variation in the terminology of capoeira in Belo Horizonte. The terms referring to 69 videotaped movements of capoeira were collected from 10 informants (5 men and 5 women, aged between 25 and 32 years, capoeira teachers. As a result we obtained 294 different terms whose patterns of variation are distributed among 15 types. We tested the hypothesis that the figurative terms tend to be replaced by non-figurative ones, and it was confirmed by the collected data. This trend was the result of a search for transparency in terminology, making the terms more descriptive in relation to capoeira’s movements.

  7. Impulse absorption by horizontal magnetic granular chain

    Directory of Open Access Journals (Sweden)

    Dingxin Leng

    2016-02-01

    Full Text Available The granular medium is known as a protecting material for shock mitigation. We study the impulse absorption of an alignment of magnetic spheres placed horizontally under a non-uniform magnetic field. The phenomenon of the wave dispersion is presented. This system can absorb 85% ∼ 95% (88% ∼ 98% of the incident peak force (energy under the applied magnetic field strength in 0.1 T ∼ 1.0 T. The shock attenuation capacities are enhanced by the increment of field strength. With an intelligent control system, it is conceivable that the magnetic granular chain may offer possibilities in developing adaptive shock protectors.

  8. Does horizontal transmission invalidate cultural phylogenies?

    Science.gov (United States)

    Greenhill, Simon J; Currie, Thomas E; Gray, Russell D

    2009-06-22

    Phylogenetic methods have recently been applied to studies of cultural evolution. However, it has been claimed that the large amount of horizontal transmission that sometimes occurs between cultural groups invalidates the use of these methods. Here, we use a natural model of linguistic evolution to simulate borrowing between languages. The results show that tree topologies constructed with Bayesian phylogenetic methods are robust to realistic levels of borrowing. Inferences about divergence dates are slightly less robust and show a tendency to underestimate dates. Our results demonstrate that realistic levels of reticulation between cultures do not invalidate a phylogenetic approach to cultural and linguistic evolution.

  9. Fluidization of a horizontally driven granular monolayer.

    Science.gov (United States)

    Heckel, Michael; Sack, Achim; Kollmer, Jonathan E; Pöschel, Thorsten

    2015-06-01

    We consider the transition of a horizontally vibrated monodisperse granular monolayer between its condensed state and its three-dimensional gaseous state as a function of the vibration parameters, amplitude, and frequency as well as particle number density. The transition is characterized by an abrupt change of the dynamical state which leaves its fingerprints in several measurable quantities including dissipation rate, sound emission, and a gap size which characterizes the sloshing motion of the material. The transition and its pronounced hysteresis is explained through the energy due to the collective motion of the particles relative to the container.

  10. Horizontal stability of a bouncing ball

    Science.gov (United States)

    McBennett, Brendan G.; Harris, Daniel M.

    2016-09-01

    We present an investigation of a partially elastic ball bouncing on a vertically vibrated concave parabolic surface in two dimensions. In particular, we demonstrate that simple vertical motion, wherein the ball bounces periodically at the parabola's vertex, is unstable to horizontal perturbations when the parabolic coefficient defining the surface shape exceeds a critical value. The result is a new periodic solution where the ball bounces laterally over the vertex. As the parabola is further steepened, this new solution also becomes unstable which gives rise to other complex periodic and chaotic bouncing states, all characterized by persistent lateral motion.

  11. Levy Flights over Quantum Paths

    CERN Document Server

    Laskin, N

    2005-01-01

    An impact of integration over the paths of the Levy flights on the quantum mechanical kernel has been studied. Analytical expression for a free particle kernel has been obtained in terms of the Fox H-function. A new equation for the kernel of a partical in the box has been found. New general results include the well known quantum formulae for a free particle kernel and particle in box kernel.

  12. The path of code linting

    CERN Document Server

    CERN. Geneva

    2017-01-01

    Join the path of code linting and discover how it can help you reach higher levels of programming enlightenment. Today we will cover how to embrace code linters to offload cognitive strain on preserving style standards in your code base as well as avoiding error-prone constructs. Additionally, I will show you the journey ahead for integrating several code linters in the programming tools your already use with very little effort.

  13. AFM's path to atomic resolution

    OpenAIRE

    2005-01-01

    We review progress in improving the spatial resolution of atomic force microscopy (AFM) under vacuum. After an introduction to the basic imaging principle and a conceptual comparison to scanning tunneling microscopy (STM), we outline the main challenges of AFM as well as the solutions that have evolved in the first 20 years of its existence. Some crucial steps along AFM's path toward higher resolution are discussed, followed by an outlook on current and future applications.

  14. Path planning under spatial uncertainty.

    Science.gov (United States)

    Wiener, Jan M; Lafon, Matthieu; Berthoz, Alain

    2008-04-01

    In this article, we present experiments studying path planning under spatial uncertainties. In the main experiment, the participants' task was to navigate the shortest possible path to find an object hidden in one of four places and to bring it to the final destination. The probability of finding the object (probability matrix) was different for each of the four places and varied between conditions. Givensuch uncertainties about the object's location, planning a single path is not sufficient. Participants had to generate multiple consecutive plans (metaplans)--for example: If the object is found in A, proceed to the destination; if the object is not found, proceed to B; and so on. The optimal solution depends on the specific probability matrix. In each condition, participants learned a different probability matrix and were then asked to report the optimal metaplan. Results demonstrate effective integration of the probabilistic information about the object's location during planning. We present a hierarchical planning scheme that could account for participants' behavior, as well as for systematic errors and differences between conditions.

  15. Effect of multiple path approach procedures on runway landing capacity. [under ILS and MLS conditions

    Science.gov (United States)

    Tosic, V.; Horonjeff, R.

    1976-01-01

    When using the Instrument Landing System (ILS) all aircraft must follow a straight line approach path before landing. The Microwave Landing System (MLS) will allow use of differing curved approach paths. The objective of this research is to find out whether the introduction of MLS and consequently multiple approach paths can bring an increase in runway landing capacity. A model is developed which is capable of computing the expected ultimate landing runway capacity, under ILS and MLS conditions, when aircraft population characteristics and Air Traffic Control separation rules are given. This model can be applied in situations when only a horizontal separation between aircraft approaching a runway is allowed, as well as when both vertical and horizontal separations are possible. Results suggest that an increase in runway landing capacity, caused by introducing the MLS-described multiple approach paths, is to be expected only when an aircraft population consists of aircraft with significantly differing approach velocities and particularly in situations when a vertical separation can be applied.

  16. Spreading paths in partially observed social networks

    CERN Document Server

    Onnela, Jukka-Pekka

    2011-01-01

    Understanding how far information, behaviors, or pathogens spread in social networks is an important problem, having implications for both predicting the size of epidemics, as well as for planning effective interventions. There are, however, two main challenges for inferring spreading path lengths in real-world networks. One is the practical difficulty of observing a dynamic process on a network, and the other is the typical constraint of only partially observing a network. Using a static, structurally realistic social network as a platform for simulations, we juxtapose three distinct paths: (1) the stochastic path taken by a simulated spreading process from source to target; (2) the topologically shortest path in the fully observed network, and hence the single most likely stochastic path, between the two nodes; and (3) the topologically shortest path in a partially observed network. In a sampled network, how closely does the partially observed shortest path (3) emulate the unobserved spreading path (1)? Alt...

  17. Time optimal paths for high speed maneuvering

    Energy Technology Data Exchange (ETDEWEB)

    Reister, D.B.; Lenhart, S.M.

    1993-01-01

    Recent theoretical results have completely solved the problem of determining the minimum length path for a vehicle with a minimum turning radius moving from an initial configuration to a final configuration. Time optimal paths for a constant speed vehicle are a subset of the minimum length paths. This paper uses the Pontryagin maximum principle to find time optimal paths for a constant speed vehicle. The time optimal paths consist of sequences of axes of circles and straight lines. The maximum principle introduces concepts (dual variables, bang-bang solutions, singular solutions, and transversality conditions) that provide important insight into the nature of the time optimal paths. We explore the properties of the optimal paths and present some experimental results for a mobile robot following an optimal path.

  18. Path-based Queries on Trajectory Data

    DEFF Research Database (Denmark)

    Krogh, Benjamin Bjerre; Pelekis, Nikos; Theodoridis, Yannis

    2014-01-01

    a specific path by only retrieving data from the first and last edge in the path. To correctly answer strict path queries existing network-constrained trajectory indexes must retrieve data from all edges in the path. An extensive performance study of NETTRA using a very large real-world trajectory data set....... To efficiently support strict path queries, we present a novel NETwork-constrained TRAjectory index (NETTRA). This index enables very efficient retrieval of trajectories that follow a specific path, i.e., strict path queries. NETTRA uses a new path encoding scheme that can determine if a trajectory follows......, consisting of 1.7 million trajectories (941 million GPS records) and a road network with 1.3 million edges, shows a speed-up of two orders of magnitude compared to state-of-the-art trajectory indexes....

  19. Generation of large-scale winds in horizontally anisotropic convection

    CERN Document Server

    von Hardenberg, J; Provenzale, A; Spiegel, E A

    2015-01-01

    We simulate three-dimensional, horizontally periodic Rayleigh-B\\'enard convection between free-slip horizontal plates, rotating about a horizontal axis. When both the temperature difference between the plates and the rotation rate are sufficiently large, a strong horizontal wind is generated that is perpendicular to both the rotation vector and the gravity vector. The wind is turbulent, large-scale, and vertically sheared. Horizontal anisotropy, engendered here by rotation, appears necessary for such wind generation. Most of the kinetic energy of the flow resides in the wind, and the vertical turbulent heat flux is much lower on average than when there is no wind.

  20. Simple method to measure effects of horizontal atmospherical turbulence at ground level

    Science.gov (United States)

    Tíjaro Rojas, Omar J.; Galeano Traslaviña, Yuber A.; Torres Moreno, Yezid

    2016-09-01

    The Kolmogorov's theory has been used to explain physical phenomena like the vertical turbulence in atmosphere, others recent works have made new advances and have improved K41 theory. In addition, this theory has been applied to studying different issues associated to measure atmospheric effects, and have special interest to find answers in optics to questions as e.g. at ground level, Could it find edges of two or more close objects, from a distant observer? (Classic resolution problem). Although this subject is still open, we did a model using the statistics of the centroid and the diameter of the laser beam propagated under horizontal turbulence at ground level until the object plane. The goal is to measure efficiently the turbulence effects in the long horizontal path propagation of electromagnetic wave. Natural movement of laser beam within the cavity needs be subtracted from the total transversal displacement in order to obtain a best approach. This simple proposed method is used to find the actual statistics of the centroid and beam diameter on the object plane where the turbulence introduces an additional transversal shift. And it has been tested for different values of horizontal distances under non-controlled environment in a synchronized acquisition scheme. Finally, we show test results in open very strong turbulence with high controlled temperature. This paper presents the implemented tests mainly into laboratory and discuss issues to resolve.

  1. Multiresolution Path Planning for Mobile Robots,

    Science.gov (United States)

    1985-05-01

    8217U’ MULTIRESOLUTION PATH PLANNING * . FOR MOBILE ROBOTS I Subbarao Kambhampati * -- Larry S. Davis Computer Vision Laboratory * Center for Automation...COUWEPARK MARVUM EP Vo Is- .. . .. CAR-TR-127 DAAK70-83-K--0018 CS-TR-1507 MAY 1085 MULTIRESOLUTION PATH PLANNING FOR MOBILE ROBOTS Subbarao Kambhampati...planning is central to mobile * robot applications. Path planning for mobile robots is in many ways different * from the more familiar case of path

  2. Multiple Paths to Encephalization and Technical Civilizations

    Science.gov (United States)

    Schwartzman, David; Middendorf, George

    2011-12-01

    We propose consideration of at least two possible evolutionary paths for the emergence of intelligent life with the potential for technical civilization. The first is the path via encephalization of homeothermic animals; the second is the path to swarm intelligence of so-called superorganisms, in particular the social insects. The path to each appears to be facilitated by environmental change: homeothermic animals by decreased climatic temperature and for swarm intelligence by increased oxygen levels.

  3. Path-Based Supports for Hypergraphs

    Science.gov (United States)

    Brandes, Ulrik; Cornelsen, Sabine; Pampel, Barbara; Sallaberry, Arnaud

    A path-based support of a hypergraph H is a graph with the same vertex set as H in which each hyperedge induces a Hamiltonian subgraph. While it is NP-complete to compute a path-based support with the minimum number of edges or to decide whether there is a planar path-based support, we show that a path-based tree support can be computed in polynomial time if it exists.

  4. Horizontal Air Bearing Experiment Number 1

    Energy Technology Data Exchange (ETDEWEB)

    Clauson, T.L.

    1999-08-31

    The Horizontal Air Bearing Experiment No.1 is a series of tests intended to further the understanding of rotational dynamics. A simple experimental assembly is rotated using the Horizontal Air Bearing and allowed to spin freely as the internal rotational damping is measured. The low friction of the bearing effectively isolates the test assembly, allowing the internal damping of the test object to be evaluated. The experimental assembly is composed of an aluminum ball within a spherical cavity. A flanged pipe section and an auxiliary adapter plate secure the assembly to the Air Bearing interface plate. Three aluminum balls are interchanged to vary test parameters. The aluminum balls are free to move independently as the entire assembly rotates. The aluminum balls vary in diameter and/or surface finish. While the diameter and surface finish is varied, the space between the ball and socket is dry. To examine the effect of viscosity, the space is filled with a lubricant while the ball diameter and surface finish is held constant.

  5. The origin of extreme horizontal branch stars

    CERN Document Server

    Dorman, B; O'Connell, R W; Dorman, Ben; Rood, Robert T; O'Connell, Robert W

    1995-01-01

    Strong mass loss on the red giant branch (RGB) can result in the formation of extreme horizontal branch (EHB) stars. The EHB stars spend most of their He core and shell burning phase at high temperatures and produce copious ultraviolet flux. They have very small hydrogen envelopes and occupy a small range in mass. We have computed evolutionary RGB models with mass loss for stars with a range of metallicities at initial masses < 1.1 Msun corresponding to populations ages between 12.5 and 14.5 Gyr. We used the Reimers formula to characterize mass loss, but investigated a larger range of the mass loss efficiency parameter, eta, than is common. To understand how the number of EHB stars varies with metallicity in a stellar population we considered how the zero-age horizontal branch (ZAHB) is populated. The range in eta producing EHB stars is comparable to that producing `mid-HB' stars. Somewhat surprisingly, neither the range nor magnitude of eta producing EHB stars varies much metallicity. In contrast, the ran...

  6. Applying GPS to check horizontal control quality

    Directory of Open Access Journals (Sweden)

    Jakub Vincent

    2004-03-01

    Full Text Available GPS technologies can also be used for check quality in available horizontal point set with coordinates CJ of the frame S-JTSK. When survey and setting-out tasks should be performed in certain area, one can found in it allways some points of the fundamental and detail state controls. To use these points for some actual aims, it is necessary to investigate their compatibility (among the point mark positions and the point coordinate of control points. This can be done using GPS surveying that may be at the same time employed to determine the new point in the relevant area.Principle of quality investigatingf an existing control is founded on determination of point coordinates CJt from GPS measurements. Then, based on discrepancies among the "official" netpoint coordinates CJ and coordinates CJt "given by GPS", it can be estimated the degree and the real compatibility dislocations in the network structure of the existing points.Realisation procedure for the introduced investigation is demonstrated on GPS checking (by SOKKIA STRATUS receivers horizontal control for reconstruction of a railway bridge on river Bodrog in East Slovakia.It can be shown from the results in Table 3, that points P3 and P7 are useless due to their incompatibility (inconsistency in the inspected point set. For other 7 points (Table 7 the average measure of incompatibility reads 9.8 mm that make possible applying these points for precise setting-out

  7. Pattern selection in a horizontally vibrated container

    Energy Technology Data Exchange (ETDEWEB)

    Porter, J; Tinao, I; Laveron-Simavilla, A; Lopez, C A, E-mail: jeff.porter@upm.es [E.T.S.I. Aeronauticos, Universidad Politecnica de Madrid, Plaza Cardenal Cisneros 3, 28040 Madrid (Spain)

    2012-10-15

    We present results of an experimental and numerical investigation of the patterns realized by surface waves within an open rectangular container subjected to horizontal vibrations at frequencies of 40-100 Hz. The first instability exhibited by the primary harmonic wave field is subharmonic, and may be identified with the cross-wave instability often seen in wave tank experiments. We show that, contrary to common theoretical and experimental assumptions, and despite their name, these subharmonic waves are not oriented crosswise, but at an intermediate angle with respect to the axis of vibration. Hence, the pattern selection problem for horizontally forced Faraday waves is more complex than has previously been assumed. We establish the robustness of this obliquely oriented surface wave pattern by varying the forcing frequency and amplitude, the fluid viscosity, the fluid depth, and the boundary conditions. Previous work on cross-waves is reviewed and discussed in relation to the current results. Finally, numerical simulations using a reduced model with an appropriate forcing term are used to support the generality of the experimental observations. (paper)

  8. Partial Path Column Generation for the ESPPRC

    DEFF Research Database (Denmark)

    Jepsen, Mads Kehlet; Petersen, Bjørn

    This talk introduces a decomposition of the Elementary Shortest Path Problem with Resource Constraints(ESPPRC), where the path is combined by smaller sub paths. We show computational result by comparing different approaches for the decomposition and compare the best of these with existing...

  9. Multi-level Indoor Path Planning Method

    NARCIS (Netherlands)

    Xiong, Q.; Zhu, Q.; Zlatanova, S.; Du, Z.; Zhang, Y.; Zeng, L.

    2015-01-01

    Indoor navigation is increasingly widespread in complex indoor environments, and indoor path planning is the most important part of indoor navigation. Path planning generally refers to finding the most suitable path connecting two locations, while avoiding collision with obstacles. However, it is a

  10. A SCALED CENTRAL PATH FOR LINEAR PROGRAMMING

    Institute of Scientific and Technical Information of China (English)

    Ya-xiang Yuan

    2001-01-01

    Interior point methods are very efficient methods for solving large scale linear programming problems. The central path plays a very important role in interior point methods. In this paper we propose a new central path, which scales the variables. Thus it has the advantage of forcing the path to have roughly the same distance from each active constraint boundary near the solution.

  11. Symbolic PathFinder v7

    DEFF Research Database (Denmark)

    Luckow, Kasper Søe; Păsăreanu, Corina

    2014-01-01

    We describe Symbolic PathFinder v7 in terms of its updated design addressing the changes of Java PathFinder v7 and of its new optimization when computing path conditions. Furthermore, we describe the Symbolic Execution Tree Extension; a newly added feature that allows for outputting the symbolic ...

  12. Classical and quantum dynamics from classical paths to path integrals

    CERN Document Server

    Dittrich, Walter

    2016-01-01

    Graduate students who want to become familiar with advanced computational strategies in classical and quantum dynamics will find here both the fundamentals of a standard course and a detailed treatment of the time-dependent oscillator, Chern-Simons mechanics, the Maslov anomaly and the Berry phase, to name a few. Well-chosen and detailed examples illustrate the perturbation theory, canonical transformations, the action principle and demonstrate the usage of path integrals. This new edition has been revised and enlarged with chapters on quantum electrodynamics, high energy physics, Green’s functions and strong interaction.

  13. No-Loss Transportation of Water Droplets by Patterning a Desired Hydrophobic Path on a Superhydrophobic Surface.

    Science.gov (United States)

    Hu, Haibao; Yu, Sixiao; Song, Dong

    2016-07-26

    The directional transportation of droplets on solid surfaces is essential in a wide range of engineering applications. It is convenient to guide liquid droplets in a given direction by utilizing the gradient of wettability, by which the binding forces can be produced. In contrast to the mass-loss transportation of a droplet moving along hydrophilic paths on a horizontal superhydrophobic surface, we present no-loss transportation by fabricating a hydrophobic path on the same surface under tangential wind. In experimental exploration and theoretical analysis, the conditions of no-loss transportation of a droplet are mainly considered. We demonstrate that the lower (or upper) critical wind velocity, under which the droplet starts on the path (or is derailed from the path), is determined by the width of the path, the length of the contact area in the direction parallel to the path, the drift angle between the path and the wind direction, and the surface wettability of the pattern. Meanwhile, the no-loss transportation of water droplets along the desired path zigzagging on a superhydrophobic surface can be achieved steadily under appropriate conditions. We anticipate that such robust no-loss transportation will find an extensive range of applications.

  14. Relations between Coherence and Path Information.

    Science.gov (United States)

    Bagan, Emilio; Bergou, János A; Cottrell, Seth S; Hillery, Mark

    2016-04-22

    We find two relations between coherence and path information in a multipath interferometer. The first builds on earlier results for the two-path interferometer, which used minimum-error state discrimination between detector states to provide the path information. For visibility, which was used in the two-path case, we substitute a recently defined l_{1} measure of quantum coherence. The second is an entropic relation in which the path information is characterized by the mutual information between the detector states and the outcome of the measurement performed on them, and the coherence measure is one based on relative entropy.

  15. Link prediction based on path entropy

    CERN Document Server

    Xu, Zhongqi; Yang, Jian

    2015-01-01

    Information theory has been taken as a prospective tool for quantifying the complexity of complex networks. In this paper, we first study the information entropy or uncertainty of a path using the information theory. Then we apply the path entropy to the link prediction problem in real-world networks. Specifically, we propose a new similarity index, namely Path Entropy (PE) index, which considers the information entropies of shortest paths between node pairs with penalization to long paths. Empirical experiments demonstrate that PE index outperforms the mainstream link predictors.

  16. Strategic Path Reliability in Information Networks

    OpenAIRE

    Kannan, Rajgopal; Sarangi, Sudipta; Iyengar, Sundaraja Sitharama

    2002-01-01

    We consider a model of an information network where nodes can fail and transmission of information is costly. The formation of paths in such networks is modeled as the Nash equilibrium of an N player routing game. The task of obtaining this equilibrium is shown to be NP-Hard. We derive analytical results to identify conditions under which the equilibrium path is congruent to well known paths such as the most reliable or cheapest neighbor path. The issue of characterizing off-equilibrium paths...

  17. Two Generations of Path Dependence in Economics?

    DEFF Research Database (Denmark)

    Madsen, Mogens Ove

    2010-01-01

    Even if there is no fully articulated and generally accepted theory of Path Dependence it has eagerly been taken up across a wide range of social sciences – primarily coming from economics. Path Dependence is most of all a metaphor that offers reason to believe, that some political, social...... or economic processes have multiple possible paths of outcomes, rather than a unique path of equilibria. The selection among outcomes may depend on contingent choices or events – outcomes of path-dependent processes require a very relevant study – a perception of history....

  18. NUMERICAL DETERMINATION OF HORIZONTAL SETTLERS PERFORMANCE

    Directory of Open Access Journals (Sweden)

    M. M. Biliaiev

    2015-08-01

    Full Text Available Purpose.Horizontal settlers are one of the most important elements in the technological scheme of water purification. Their use is associated with the possibility to pass a sufficiently large volume of water. The important task at the stage of their designing is evaluating of their effectiveness. Calculation of the efficiency of the settler can be made by mathematical modeling. Empirical, analytical models and techniques that are currently used to solve the problem, do not allow to take into account the shape of the sump and various design features that significantly affects the loyalty to a decision on the choice of the size of the settling tank and its design features. The use of analytical models is limited only to one-dimensional solutions, does not allow accounting for nonuniform velocity field of the flow in the settler. The use of advanced turbulence models for the calculation of the hydrodynamics in the settler complex forms now requires very powerful computers. In addition, the calculation of one variant of the settler may last for dozens of hours. The aim of the paper is to build a numerical model to evaluate the effectiveness of horizontal settling tank modified design. Methodology. Numerical models are based on: 1 equation of potential flow; 2 equation of inviscid fluid vortex flow; 3 equation of viscous fluid dynamics; 4 mass transfer equation. For numerical simulation the finite difference schemes are used. The numerical calculation is carried out on a rectangular grid. For the formation of the computational domain markers are used. Findings.The models allow calculating the clarification process in the settler with different form and different configuration of baffles. Originality. A new approach to investigate the mass transfer process in horizontal settler was proposed. This approach is based on the developed CFD models. Three fluid dynamics models were used for the numerical investigation of flows and waste waters purification

  19. A novel monocular visual navigation method for cotton-picking robot based on horizontal spline segmentation

    Science.gov (United States)

    Xu, ShengYong; Wu, JuanJuan; Zhu, Li; Li, WeiHao; Wang, YiTian; Wang, Na

    2015-12-01

    Visual navigation is a fundamental technique of intelligent cotton-picking robot. There are many components and cover in the cotton field, which make difficulties of furrow recognition and trajectory extraction. In this paper, a new field navigation path extraction method is presented. Firstly, the color image in RGB color space is pre-processed by the OTSU threshold algorithm and noise filtering. Secondly, the binary image is divided into numerous horizontally spline areas. In each area connected regions of neighboring images' vertical center line are calculated by the Two-Pass algorithm. The center points of the connected regions are candidate points for navigation path. Thirdly, a series of navigation points are determined iteratively on the principle of the nearest distance between two candidate points in neighboring splines. Finally, the navigation path equation is fitted by the navigation points using the least squares method. Experiments prove that this method is accurate and effective. It is suitable for visual navigation in the complex environment of cotton field in different phases.

  20. Evaluation of guidewire path reproducibility.

    Science.gov (United States)

    Schafer, Sebastian; Hoffmann, Kenneth R; Noël, Peter B; Ionita, Ciprian N; Dmochowski, Jacek

    2008-05-01

    The number of minimally invasive vascular interventions is increasing. In these interventions, a variety of devices are directed to and placed at the site of intervention. The device used in almost all of these interventions is the guidewire, acting as a monorail for all devices which are delivered to the intervention site. However, even with the guidewire in place, clinicians still experience difficulties during the interventions. As a first step toward understanding these difficulties and facilitating guidewire and device guidance, we have investigated the reproducibility of the final paths of the guidewire in vessel phantom models on different factors: user, materials and geometry. Three vessel phantoms (vessel diameters approximately 4 mm) were constructed having tortuousity similar to the internal carotid artery from silicon tubing and encased in Sylgard elastomer. Several trained users repeatedly passed two guidewires of different flexibility through the phantoms under pulsatile flow conditions. After the guidewire had been placed, rotational c-arm image sequences were acquired (9 in. II mode, 0.185 mm pixel size), and the phantom and guidewire were reconstructed (512(3), 0.288 mm voxel size). The reconstructed volumes were aligned. The centerlines of the guidewire and the phantom vessel were then determined using region-growing techniques. Guidewire paths appear similar across users but not across materials. The average root mean square difference of the repeated placement was 0.17 +/- 0.02 mm (plastic-coated guidewire), 0.73 +/- 0.55 mm (steel guidewire) and 1.15 +/- 0.65 mm (steel versus plastic-coated). For a given guidewire, these results indicate that the guidewire path is relatively reproducible in shape and position.

  1. Attention trees and semantic paths

    Science.gov (United States)

    Giusti, Christian; Pieroni, Goffredo G.; Pieroni, Laura

    2007-02-01

    In the last few decades several techniques for image content extraction, often based on segmentation, have been proposed. It has been suggested that under the assumption of very general image content, segmentation becomes unstable and classification becomes unreliable. According to recent psychological theories, certain image regions attract the attention of human observers more than others and, generally, the image main meaning appears concentrated in those regions. Initially, regions attracting our attention are perceived as a whole and hypotheses on their content are formulated; successively the components of those regions are carefully analyzed and a more precise interpretation is reached. It is interesting to observe that an image decomposition process performed according to these psychological visual attention theories might present advantages with respect to a traditional segmentation approach. In this paper we propose an automatic procedure generating image decomposition based on the detection of visual attention regions. A new clustering algorithm taking advantage of the Delaunay- Voronoi diagrams for achieving the decomposition target is proposed. By applying that algorithm recursively, starting from the whole image, a transformation of the image into a tree of related meaningful regions is obtained (Attention Tree). Successively, a semantic interpretation of the leaf nodes is carried out by using a structure of Neural Networks (Neural Tree) assisted by a knowledge base (Ontology Net). Starting from leaf nodes, paths toward the root node across the Attention Tree are attempted. The task of the path consists in relating the semantics of each child-parent node pair and, consequently, in merging the corresponding image regions. The relationship detected in this way between two tree nodes generates, as a result, the extension of the interpreted image area through each step of the path. The construction of several Attention Trees has been performed and partial

  2. Communication path for extreme environments

    Science.gov (United States)

    Jorgensen, Charles C. (Inventor); Betts, Bradley J. (Inventor)

    2010-01-01

    Methods and systems for using one or more radio frequency identification devices (RFIDs), or other suitable signal transmitters and/or receivers, to provide a sensor information communication path, to provide location and/or spatial orientation information for an emergency service worker (ESW), to provide an ESW escape route, to indicate a direction from an ESW to an ES appliance, to provide updated information on a region or structure that presents an extreme environment (fire, hazardous fluid leak, underwater, nuclear, etc.) in which an ESW works, and to provide accumulated thermal load or thermal breakdown information on one or more locations in the region.

  3. Uncommon paths in quantum physics

    CERN Document Server

    Kazakov, Konstantin V

    2014-01-01

    Quantum mechanics is one of the most fascinating, and at the same time most controversial, branches of contemporary science. Disputes have accompanied this science since its birth and have not ceased to this day. Uncommon Paths in Quantum Physics allows the reader to contemplate deeply some ideas and methods that are seldom met in the contemporary literature. Instead of widespread recipes of mathematical physics, based on the solutions of integro-differential equations, the book follows logical and partly intuitional derivations of non-commutative algebra. Readers can directly penetrate the

  4. Gibbs Ensembles of Nonintersecting Paths

    CERN Document Server

    Borodin, Alexei

    2008-01-01

    We consider a family of determinantal random point processes on the two-dimensional lattice and prove that members of our family can be interpreted as a kind of Gibbs ensembles of nonintersecting paths. Examples include probability measures on lozenge and domino tilings of the plane, some of which are non-translation-invariant. The correlation kernels of our processes can be viewed as extensions of the discrete sine kernel, and we show that the Gibbs property is a consequence of simple linear relations satisfied by these kernels. The processes depend on infinitely many parameters, which are closely related to parametrization of totally positive Toeplitz matrices.

  5. On the path to differentiation

    DEFF Research Database (Denmark)

    Martinsen, Dorte Sindbjerg; Uygur, Ayca

    2014-01-01

    by examining the ‘path to differentiation’ within EU working time regulation as it has unfolded over time. It identifies the ‘opt-out’ as a means of differentiation adopted to overcome policy deadlocks within collective decision-making, albeit one with unforeseen consequences. In particular, the contribution...... investigates the causes and effects of differentiation by examining (1) its origin, (2) the ‘logic of variation’ or ‘opt-out spiral’ that spurs differentiation and (3) the implications of differentiation over time. We conclude that differentiation has dynamic and broad consequences that are likely to produce...

  6. Path of Chinese institutional modernization

    OpenAIRE

    Sahoo, Ganeswar

    2009-01-01

    We see the progress today that China has developed a treasure of modernity in terms of its World figure both in economic development and its strong military power with countless path of ups and downs in the past. We are more concerned with the historical study of its institutional modernization than a mere philosophical debate over its development and can discuss its various levels of struggle for ‘Substitute Modernity’2 since mid-19th century(the two opium wars) to till date.

  7. Paths and cycles of hypergraphs

    Institute of Scientific and Technical Information of China (English)

    王建方; Tony; T.Lee

    1999-01-01

    Hypergraphs are the most general structures in discrete mathematics. Acyclic hypergraphs have been proved very useful in relational databases. New systems of axioms for paths, connectivity and cycles of hypergraphs are constructed. The systems suit the structure properties of relational databases. The concepts of pseudo cycles and essential cycles of hypergraphs are introduced. They are relative to each other. Whether a family of cycles of a hypergraph is dependent or independent is defined. An enumeration formula for the maximum number of independent essential cycles of a hypergraph is given.

  8. Physarum Can Compute Shortest Paths

    CERN Document Server

    Bonifaci, Vincenzo; Varma, Girish

    2011-01-01

    A mathematical model has been proposed by biologists to describe the feedback mechanism used by the Physarum Polycephalum slime mold to adapt its tubular channels while foraging two food sources $s_0$ and $s_1$. We give a proof of the fact that, under this model, the mass of the mold will eventually converge to the shortest $s_0$-$s_1$ path of the network that the mold lies on, independently of the structure of the network or of the initial mass distribution. This matches the experimental observations by the biologists and can be seen as an example of a "natural algorithm", that is, an algorithm developed by evolution over millions of years.

  9. Deterministic Circular Self Test Path

    Institute of Scientific and Technical Information of China (English)

    WEN Ke; HU Yu; LI Xiaowei

    2007-01-01

    Circular self test path (CSTP) is an attractive technique for testing digital integrated circuits(IC) in the nanometer era, because it can easily provide at-speed test with small test data volume and short test application time. However, CSTP cannot reliably attain high fault coverage because of difficulty of testing random-pattern-resistant faults. This paper presents a deterministic CSTP (DCSTP) structure that consists of a DCSTP chain and jumping logic, to attain high fault coverage with low area overhead. Experimental results on ISCAS'89 benchmarks show that 100% fault coverage can be obtained with low area overhead and CPU time, especially for large circuits.

  10. The Shortest Path with Intelligent Algorithm

    Directory of Open Access Journals (Sweden)

    Surachai Panich

    2010-01-01

    Full Text Available Problem statement: Path planning algorithms need to be developed and implemented in a suitable manner to give better understanding about the intelligent system and also stimulates technological supply to enormous demands in an intelligent vehicle industry. Approach: This study concerned with intelligent path planning using A* search algorithm. Results: This study introduced intelligent path planning with A* search algorithm, which use to generate the most efficient path to goal. The algorithm was tested on simulator. Conclusion: This study is an implementation of a path planning for an intelligent path planning. The implementations are tested and verified with the simulation software. The path planning algorithms were selected for the implementation and to verify them.

  11. Longest-path attacks on complex networks

    CERN Document Server

    Pu, Cunlai

    2014-01-01

    We investigate the longest-path attacks on complex networks. Specifically, we remove approximately the longest simple path from a network iteratively until there are no paths left in the network. We propose two algorithms, the random augmenting approach (RPA) and the Hamilton-path based approach (HPA), for finding the approximately longest simple path in a network. Results demonstrate that steps of longest-path attacks increase with network density linearly for random networks, while exponentially increasing for scale-free networks. The more homogeneous the degree distribution is, the more fragile the network, which is totally different from the previous results of node or edge attacks. HPA is generally more efficient than RPA in the longest-path attacks of complex networks. These findings further help us understand the vulnerability of complex systems, better protect complex systems, and design more tolerant complex systems.

  12. Horizon-T Experiment Calibrations - Cables

    CERN Document Server

    Beznosko, D; Iakovlev, A; Makhataeva, Z; Vildanova, M I; Yelshibekov, K; Zhukov, V V

    2016-01-01

    An innovative detector system called Horizon-T is constructed to study Extensive Air Showers (EAS) in the energy range above 1016 eV coming from a wide range of zenith angles (0o - 85o). The system is located at Tien Shan high-altitude Science Station of Lebedev Physical Institute of the Russian Academy of Sciences at approximately 3340 meters above the sea level. The detector consists of eight charged particle detection points separated by the distance up to one kilometer as well as optical detector to view the Vavilov-\\v{C}erenkov light from the EAS. Each detector connects to the Data Acquisition system via cables. The calibration of the time delay for each cable and the signal attenuation is provided in this article.

  13. Modelling the horizontal steam generator with APROS

    Energy Technology Data Exchange (ETDEWEB)

    Ylijoki, J. [VTT Energy, Espoo (Finland); Palsinajaervi, C.; Porkholm, K. [IVO International Ltd, Vantaa (Finland)

    1995-12-31

    In this paper the capability of the five- and six-equation models of the simulation code APROS to simulate the behaviour of the horizontal steam generator is discussed. Different nodalizations are used in the modelling and the results of the stationary state runs are compared. Exactly the same nodalizations have been created for the five- and six-equation models. The main simulation results studied in this paper are void fraction and mass flow distributions in the secondary side of the steam generator. It was found that quite a large number of simulation volumes is required to simulate the distributions with a reasonable accuracy. The simulation results of the different models are presented and their validity is discussed. (orig.). 4 refs.

  14. Horizontal gene exchange in environmental microbiota

    Directory of Open Access Journals (Sweden)

    Rustam I Aminov

    2011-07-01

    Full Text Available Horizontal gene transfer (HGT plays an important role in the evolution of life on the Earth. This view is supported by numerous occasions of HGT that are recorded in the genomes of all three domains of living organisms. HGT-mediated rapid evolution is especially noticeable among the Bacteria, which demonstrate formidable adaptability in the face of recent environmental changes imposed by human activities, such as the use of antibiotics, industrial contamination, and intensive agriculture. At the heart of the HGT-driven bacterial evolution and adaptation are highly sophisticated natural genetic engineering tools in the form of a variety of mobile genetic elements (MGEs. The main aim of this review is to give a brief account of the occurrence and diversity of MGEs in natural ecosystems and of the environmental factors that may affect MGE-mediated HGT.

  15. Multimodal Distributions along the Horizontal Branch

    CERN Document Server

    Ferraro, F R; Pecci, F F; Dorman, B; Rood, R T; Ferraro, Francesco R.; Paltrinieri, Barbara; Pecci, Flavio Fusi; Dorman, Ben; Rood, Robert T.

    1997-01-01

    We report on HST/WFPC2 U,V and far-ultraviolet observations of two Galactic Globular Clusters (GGCs), NGC 6205 = M13 and NGC 6093 = M80. Both of these clusters have horizontal-branch (HB) tails that extend to the helium-burning main sequence, with the hottest stars reaching theoretical effective temperatures above 35,000 K. In both clusters, groups of stars are found to be separated by narrow gaps along the blue HB sequence. These gaps appear at similar locations in the color-magnitude diagrams of the two clusters. While stochastic effects may give rise to variations in the color distribution along the HB, the coincidence of gaps in different clusters effectively rules this out as the primary cause. The comparison among the clusters strongly suggests that there are separate physical processes operating during the earlier red-giant phase of evolution to produce mass loss.

  16. Horizontal stresses below two agricultural vehicles

    DEFF Research Database (Denmark)

    Lamande, Mathieu André Maurice; Munkholm, Lars Juhl; Nielsen, Janne Aalborg

    , while shear stress larger than soil strength may affect intensity soil properties (i.e. air permeability) by soil deformation not necessarily associated with compaction. In previous experiments in field conditions, isotropic compaction was observed below the center of tires, while shearing took place...... below the edge of tires. Stress distribution at the tire/soil contact is not uniform. Dimensions and inflation pressure are key factors for the ability of agricultural tires to distribute the wheel load. Our hypothesis was that the risk of shearing increases with the tire inflation pressure...... and the number of wheels. We measured horizontal stress at two depths (0.3 and 0.5 m) below tires of two slurry spreaders: one self-propelled machine equipped with wide tires (1.050 m) and low inflation pressure (150 kPa) but carrying a high wheel load (120 kN), and one tractor towing a three-axle slurry...

  17. Passive magnetic bearing for a horizontal shaft

    Energy Technology Data Exchange (ETDEWEB)

    Post, Richard F.

    2003-12-02

    A passive magnetic bearing is composed of a levitation element and a restorative element. The levitation element is composed of a pair of stationary arcuate ferromagnetic segments located within an annular radial-field magnet array. The magnet array is attached to the inner circumference of a hollow shaft end. An attractive force between the arcuate segments and the magnet array acts vertically to levitate the shaft, and also in a horizontal transverse direction to center the shaft. The restorative element is comprised of an annular Halbach array of magnets and a stationary annular circuit array located within the Halbach array. The Halbach array is attached to the inner circumference of the hollow shaft end. A repulsive force between the Halbach array and the circuit array increases inversely to the radial space between them, and thus acts to restore the shaft to its equilibrium axis of rotation when it is displaced therefrom.

  18. Numerical Investigation on Submerged Horizontal Plate

    Institute of Scientific and Technical Information of China (English)

    康海贵; 王科

    2001-01-01

    Hydrodynamic characters on a horizontal, thin, rigid plate located beneath the free surface are numerically investigated. Assuming a linear, time-harmonic potential flow and utilizing Green identity, the governing Laplace equation can be simplified into Fredholm integral equation ofthe second kind. Supposing linear-order discontinuous elements along intersecting vertical boundaries, and by use of the boundary element method, numerical solution about source strength distribution on the plate can be changed into a series of algebraic equations. The 3D Green function is introduced to set up the integral equations, and the GMRES solver is performed for solving the large dense linear system of equations. The added-mass, damping force and exciting force are evaluated directly from the equations. It is found that the added-mass coefficient becomes negative for a range of frequencies when the plate is sufficiently close to the free surface.

  19. Horizontal Gene Transfer, Dispersal and Haloarchaeal Speciation

    Directory of Open Access Journals (Sweden)

    R. Thane Papke

    2015-05-01

    Full Text Available The Halobacteria are a well-studied archaeal class and numerous investigations are showing how their diversity is distributed amongst genomes and geographic locations. Evidence indicates that recombination between species continuously facilitates the arrival of new genes, and within species, it is frequent enough to spread acquired genes amongst all individuals in the population. To create permanent independent diversity and generate new species, barriers to recombination are probably required. The data support an interpretation that rates of evolution (e.g., horizontal gene transfer and mutation are faster at creating geographically localized variation than dispersal and invasion are at homogenizing genetic differences between locations. Therefore, we suggest that recurrent episodes of dispersal followed by variable periods of endemism break the homogenizing forces of intrapopulation recombination and that this process might be the principal stimulus leading to divergence and speciation in Halobacteria.

  20. Horizontal Gene Transfer, Dispersal and Haloarchaeal Speciation

    Science.gov (United States)

    Papke, R. Thane; Corral, Paulina; Ram-Mohan, Nikhil; de la Haba, Rafael R.; Sánchez-Porro, Cristina; Makkay, Andrea; Ventosa, Antonio

    2015-01-01

    The Halobacteria are a well-studied archaeal class and numerous investigations are showing how their diversity is distributed amongst genomes and geographic locations. Evidence indicates that recombination between species continuously facilitates the arrival of new genes, and within species, it is frequent enough to spread acquired genes amongst all individuals in the population. To create permanent independent diversity and generate new species, barriers to recombination are probably required. The data support an interpretation that rates of evolution (e.g., horizontal gene transfer and mutation) are faster at creating geographically localized variation than dispersal and invasion are at homogenizing genetic differences between locations. Therefore, we suggest that recurrent episodes of dispersal followed by variable periods of endemism break the homogenizing forces of intrapopulation recombination and that this process might be the principal stimulus leading to divergence and speciation in Halobacteria. PMID:25997110

  1. A horse’s locomotor signature: COP path determined by the individual limb

    Science.gov (United States)

    Hobbs, Sarah Jane; Back, Willem

    2017-01-01

    Introduction Ground reaction forces in sound horses with asymmetric hooves show systematic differences in the horizontal braking force and relative timing of break-over. The Center Of Pressure (COP) path quantifies the dynamic load distribution under the hoof in a moving horse. The objective was to test whether anatomical asymmetry, quantified by the difference in dorsal wall angle between the left and right forelimbs, correlates with asymmetry in the COP path between these limbs. In addition, repeatability of the COP path was investigated. Methods A larger group (n = 31) visually sound horses with various degree of dorsal hoof wall asymmetry trotted three times over a pressure mat. COP path was determined in a hoof-bound coordinate system. A relationship between correlations between left and right COP paths and degree of asymmetry was investigated. Results Using a hoof-bound coordinate system made the COP path highly repeatable and unique for each limb. The craniocaudal patterns are usually highly correlated between left and right, but the mediolateral patterns are not. Some patterns were found between COP path and dorsal wall angle but asymmetry in dorsal wall angle did not necessarily result in asymmetry in COP path and the same could be stated for symmetry. Conclusion This method is a highly sensitive method to quantify the net result of the interaction between all of the forces and torques that occur in the limb and its inertial properties. We argue that changes in motor control, muscle force, inertial properties, kinematics and kinetics can potentially be picked up at an early stage using this method and could therefore be used as an early detection method for changes in the musculoskeletal apparatus. PMID:28196073

  2. novos elementos e horizontes para o cuidado

    Directory of Open Access Journals (Sweden)

    Rosa Lúcia Rocha Ribeiro

    2007-01-01

    Full Text Available La condición crónica ha sido un tema de importancia extrema para la reflexión del proceso de vivir humano. En el artículo se presenta la síntesis de una investigación realizada con la finalidad de comprender cómo los niños con Síndrome Nefrótico son cuidados, buscando identificar nuevos elementos y horizontes para reconstruir el cuidado de enfermería, teniendo como foco la familia. Para la presente investigación, se realizó un estudio cualitativo que utilizó como referente teórico metodológico, la hermenéutica basada en Gadamer y Ricouer. De la investigación realizada en 2004, participaron 42 personas pertenecientes a las familias de niños y adolescentes con Síndrome Nefrótico, usuarias del Servicio de Nefrología Pediátrica del Hospital Universitario Júlio Müller, en Cuiabá, Brasil. En la discusión son presentadas: una síntesis de las familias, sus proyectos, personajes y contexto; la trayectoria de la enfermedad del niño en la familia, y el cuidado del niño nefrótico en la familia. Se muestran también los horizontes de los cuidadores, familiares y profesionales de salud, y el cuidado posible a partir de los arreglos de la familia. Se puede concluir que el diálogo es la primera condición para la comprensión y también para el cuidado.

  3. Classical and quantum dynamics from classical paths to path integrals

    CERN Document Server

    Dittrich, Walter

    2017-01-01

    Graduate students who wish to become familiar with advanced computational strategies in classical and quantum dynamics will find in this book both the fundamentals of a standard course and a detailed treatment of the time-dependent oscillator, Chern-Simons mechanics, the Maslov anomaly and the Berry phase, to name just a few topics. Well-chosen and detailed examples illustrate perturbation theory, canonical transformations and the action principle, and demonstrate the usage of path integrals. The fifth edition has been revised and enlarged to include chapters on quantum electrodynamics, in particular, Schwinger’s proper time method and the treatment of classical and quantum mechanics with Lie brackets and pseudocanonical transformations. It is shown that operator quantum electrodynamics can be equivalently described with c-numbers, as demonstrated by calculating the propagation function for an electron in a prescribed classical electromagnetic field.

  4. Bilateral horizontal Vogt’s striae in keratoconus

    Directory of Open Access Journals (Sweden)

    Inci Ulu Güngör

    2008-10-01

    Full Text Available Inci Ulu Güngör, Ümit Beden, Baris SönmezOndokuz Mayis University, School of Medicine, Department of Ophthalmology, Samsun, TurkeyPurpose: To report a keratoconus case with bilateral horizontal Vogt’s striae.Method: The clinical findings of the patient and the development of the direction of striae are discussed.Results: Vogt’s striae, defined as vertical stress lines, are rarely horizontal. One patient with unilateral horizontal stress lines on his left eye has been reported in the literature. Our patient has horizontal Vogt’s striae in both eyes.Conclusion: Horizontal Vogt’s striae may be seen in keratoconus as a rare slit-lamp biomicroscopic finding.Keywords: keratoconus, Vogt’s striae, horizontal stress lines

  5. Evolutionary paths of streptococcal and staphylococcal superantigens

    Directory of Open Access Journals (Sweden)

    Okumura Kayo

    2012-08-01

    Full Text Available Abstract Background Streptococcus pyogenes (GAS harbors several superantigens (SAgs in the prophage region of its genome, although speG and smez are not located in this region. The diversity of SAgs is thought to arise during horizontal transfer, but their evolutionary pathways have not yet been determined. We recently completed sequencing the entire genome of S. dysgalactiae subsp. equisimilis (SDSE, the closest relative of GAS. Although speG is the only SAg gene of SDSE, speG was present in only 50% of clinical SDSE strains and smez in none. In this study, we analyzed the evolutionary paths of streptococcal and staphylococcal SAgs. Results We compared the sequences of the 12–60 kb speG regions of nine SDSE strains, five speG+ and four speG–. We found that the synteny of this region was highly conserved, whether or not the speG gene was present. Synteny analyses based on genome-wide comparisons of GAS and SDSE indicated that speG is the direct descendant of a common ancestor of streptococcal SAgs, whereas smez was deleted from SDSE after SDSE and GAS split from a common ancestor. Cumulative nucleotide skew analysis of SDSE genomes suggested that speG was located outside segments of steeper slopes than the stable region in the genome, whereas the region flanking smez was unstable, as expected from the results of GAS. We also detected a previously undescribed staphylococcal SAg gene, selW, and a staphylococcal SAg -like gene, ssl, in the core genomes of all Staphylococcus aureus strains sequenced. Amino acid substitution analyses, based on dN/dS window analysis of the products encoded by speG, selW and ssl suggested that all three genes have been subjected to strong positive selection. Evolutionary analysis based on the Bayesian Markov chain Monte Carlo method showed that each clade included at least one direct descendant. Conclusions Our findings reveal a plausible model for the comprehensive evolutionary pathway of streptococcal and

  6. Characterizing local variability in long‐period horizontal tilt noise

    Science.gov (United States)

    Rohde, M.D.; Ringler, Adam; Hutt, Charles R.; Wilson, David; Holland, Austin; Sandoval, L.D; Storm, Tyler

    2017-01-01

    Horizontal seismic data are dominated by atmospherically induced tilt noise at long periods (i.e., 30 s and greater). Tilt noise limits our ability to use horizontal data for sensitive seismological studies such as observing free earth modes. To better understand the local spatial variability of long‐period horizontal noise, we observe horizontal noise during quiet time periods in the Albuquerque Seismological Laboratory (ASL) underground vault using four small‐aperture array configurations. Each array comprises eight Streckeisen STS‐2 broadband seismometers. We analyze the spectral content of the data using power spectral density and magnitude‐squared coherence (γ2‐coherence). Our results show a high degree of spatial variability and frequency dependence in the long‐period horizontal wavefield. The variable nature of long‐period horizontal noise in the ASL vault suggests that it might be highly local in nature and not easily characterized by simple physical models when overall noise levels are low, making it difficult to identify locations in the vault with lower horizontal noise. This variability could be limiting our ability to apply coherence analysis for estimating horizontal sensor self‐noise and could also complicate various indirect methods for removing long‐period horizontal noise (e.g., collocated rotational sensor or microbarograph).

  7. Cuttings Transport Models and Experimental Visualization of Underbalanced Horizontal Drilling

    Directory of Open Access Journals (Sweden)

    Na Wei

    2013-01-01

    Full Text Available Aerated underbalanced horizontal drilling technology has become the focus of the drilling industry at home and abroad, and one of the engineering core issues is the horizontal borehole cleaning. Therefore, calculating the minimum injection volume of gas and liquid accurately is essential for the construction in aerated underbalanced horizontal drilling. This paper establishes a physical model of carrying cuttings and borehole cleaning in wellbore of horizontal well and a critical transport mathematical model according to gas-liquid-solid flow mechanism and large plane dunes particle transport theory.

  8. Integrated assignment and path planning

    Science.gov (United States)

    Murphey, Robert A.

    2005-11-01

    A surge of interest in unmanned systems has exposed many new and challenging research problems across many fields of engineering and mathematics. These systems have the potential of transforming our society by replacing dangerous and dirty jobs with networks of moving machines. This vision is fundamentally separate from the modern view of robotics in that sophisticated behavior is realizable not by increasing individual vehicle complexity, but instead through collaborative teaming that relies on collective perception, abstraction, decision making, and manipulation. Obvious examples where collective robotics will make an impact include planetary exploration, space structure assembly, remote and undersea mining, hazardous material handling and clean-up, and search and rescue. Nonetheless, the phenomenon driving this technology trend is the increasing reliance of the US military on unmanned vehicles, specifically, aircraft. Only a few years ago, following years of resistance to the use of unmanned systems, the military and civilian leadership in the United States reversed itself and have recently demonstrated surprisingly broad acceptance of increasingly pervasive use of unmanned platforms in defense surveillance, and even attack. However, as rapidly as unmanned systems have gained acceptance, the defense research community has discovered the technical pitfalls that lie ahead, especially for operating collective groups of unmanned platforms. A great deal of talent and energy has been devoted to solving these technical problems, which tend to fall into two categories: resource allocation of vehicles to objectives, and path planning of vehicle trajectories. An extensive amount of research has been conducted in each direction, yet, surprisingly, very little work has considered the integrated problem of assignment and path planning. This dissertation presents a framework for studying integrated assignment and path planning and then moves on to suggest an exact

  9. Extracting Critical Path Graphs from MPI Applications

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, M

    2005-07-27

    The critical path is one of the fundamental runtime characteristics of a parallel program. It identifies the longest execution sequence without wait delays. In other words, the critical path is the global execution path that inflicts wait operations on other nodes without itself being stalled. Hence, it dictates the overall runtime and knowing it is important to understand an application's runtime and message behavior and to target optimizations. We have developed a toolset that identifies the critical path of MPI applications, extracts it, and then produces a graphical representation of the corresponding program execution graph to visualize it. To implement this, we intercept all MPI library calls, use the information to build the relevant subset of the execution graph, and then extract the critical path from there. We have applied our technique to several scientific benchmarks and successfully produced critical path diagrams for applications running on up to 128 processors.

  10. Strategic Team AI Path Plans: Probabilistic Pathfinding

    Directory of Open Access Journals (Sweden)

    Tng C. H. John

    2008-01-01

    Full Text Available This paper proposes a novel method to generate strategic team AI pathfinding plans for computer games and simulations using probabilistic pathfinding. This method is inspired by genetic algorithms (Russell and Norvig, 2002, in that, a fitness function is used to test the quality of the path plans. The method generates high-quality path plans by eliminating the low-quality ones. The path plans are generated by probabilistic pathfinding, and the elimination is done by a fitness test of the path plans. This path plan generation method has the ability to generate variation or different high-quality paths, which is desired for games to increase replay values. This work is an extension of our earlier work on team AI: probabilistic pathfinding (John et al., 2006. We explore ways to combine probabilistic pathfinding and genetic algorithm to create a new method to generate strategic team AI pathfinding plans.

  11. Path modeling and process control

    DEFF Research Database (Denmark)

    Høskuldsson, Agnar; Rodionova, O.; Pomerantsev, A.

    2007-01-01

    and having three or more stages. The methods are applied to a process control of a multi-stage production process having 25 variables and one output variable. When moving along the process, variables change their roles. It is shown how the methods of path modeling can be applied to estimate variables...... of the next stage with the purpose of obtaining optimal or almost optimal quality of the output variable. An important aspect of the methods presented is the possibility of extensive graphic analysis of data that can provide the engineer with a detailed view of the multi-variate variation in data.......Many production processes are carried out in stages. At the end of each stage, the production engineer can analyze the intermediate results and correct process parameters (variables) of the next stage. Both analysis of the process and correction to process parameters at next stage should...

  12. The Logic Behind Feynman's Paths

    Science.gov (United States)

    García Álvarez, Edgardo T.

    The classical notions of continuity and mechanical causality are left in order to reformulate the Quantum Theory starting from two principles: (I) the intrinsic randomness of quantum process at microphysical level, (II) the projective representations of symmetries of the system. The second principle determines the geometry and then a new logic for describing the history of events (Feynman's paths) that modifies the rules of classical probabilistic calculus. The notion of classical trajectory is replaced by a history of spontaneous, random and discontinuous events. So the theory is reduced to determining the probability distribution for such histories accordingly with the symmetries of the system. The representation of the logic in terms of amplitudes leads to Feynman rules and, alternatively, its representation in terms of projectors results in the Schwinger trace formula.

  13. Innovation paths in wind power

    DEFF Research Database (Denmark)

    Lema, Rasmus; Nordensvärd, Johan; Urban, Frauke

    Denmark and Germany both make substantial investments in low carbon innovation, not least in the wind power sector. These investments in wind energy are driven by the twin objectives of reducing carbon emissions and building up international competitive advantage. Support for wind power dates back...... between Denmark and Germany when it comes to innovation pathways, both in technological and organisational innovation. In turbine technology, the similarities are the constant increase in turbine size and quality. The key difference to be found is the relative importance of different turbine designs....... The ‘Danish Design’ remains the global standard. The direct drive design, while uncommon in Denmark, dominates the German installation base. Direct drive technology has thus emerged as a distinctly German design and sub-trajectory within the overall technological innovation path. When it comes to organising...

  14. Effect of optical turbulence along a downward slant path on probability of laser hazard

    Science.gov (United States)

    Gustafsson, K. Ove S.

    2016-10-01

    The importance of the optical turbulence effect along a slant path downward on probability of exceeding the maximum permissible exposure level (MPE) from a laser is discussed. The optical turbulence is generated by fluctuations (variations) in refractive index of the atmosphere. These fluctuations are caused in turn by changes in atmospheric temperature and humidity. The structure function of refractive index, Cn2, is the single most important parameter in the description of turbulence effects on the propagation of electromagnetic radiation. In the boundary layer, the lowest part of the atmosphere where the ground directly influence the atmosphere, is the variation of Cn2 in Sweden between about 10-17 and 10-12 m-2/3, see Bergström et al. [5]. Along a horizontal path is the Cn 2 often assumed to be constant. The variation of the Cn2 along a slant path is described by the Tatarski model as function of height to the power of -4/3 or -2/3, depending on day or night conditions. The hazard of laser damage of eye is calculated for a long slant path downward. The probability of exceeding the maximum permissible exposure (MPE) level is given as a function of distance in comparison with nominal ocular hazard distance (NOHD) for adopted levels of turbulence. Furthermore, calculations are carried out for a laser pointer or a designator laser from a high altitude and long distance down to a ground target. The used example shows that there is an 10% risk of exceeding the MPE at a distance 2 km beyond the NOHD, in this example 48 km, due to turbulence level of 5·10-15 m-2/3 at ground height. The turbulence influence on a laser beam along horizontal path on NOHD have been shown before by Zilberman et al. [4].

  15. Design of active N-path filters

    NARCIS (Netherlands)

    Darvishi, Milad; Zee, van der Ronan; Nauta, Bram

    2013-01-01

    A design methodology for synthesis of active N-path bandpass filters is introduced. Based on this methodology, a 0.1-to-1.2 GHz tunable 6th-order N-path channel-select filter in 65 nm LP CMOS is introduced. It is based on coupling N-path filters with gyrators, achieving a “flat” passband shape and h

  16. Path Planning Control for Mobile Robot

    Directory of Open Access Journals (Sweden)

    Amenah A.H. Salih

    2011-01-01

    Full Text Available Autonomous motion planning is important area of robotics research. This type of planning relieves human operator from tedious job of motion planning. This reduces the possibility of human error and increase efficiency of whole process. This research presents a new algorithm to plan path for autonomous mobile robot based on image processing techniques by using wireless camera that provides the desired image for the unknown environment . The proposed algorithm is applied on this image to obtain a optimal path for the robot. It is based on the observation and analysis of the obstacles that lying in the straight path between the start and the goal point by detecting these obstacles, analyzing and studying their shapes, positions and points of intersection with the straight path to find the nearly optimal path which connects the start and the goal point.This work has theoretical part and experimental part. The theoretical part includes building a MATLAB program which is applied to environment image to find the nearly optimal path .MATLAB - C++.NET interface is accomplished then to supply the path information for C++.NET program which is done for programming the pioneer mobile robot to achieve the desired path. The experimental part includes using wireless camera that takes an image for the environment and send it to the computer which processes this image and sends ( by wireless connection the resulted path information to robot which programmed in C++.NET program to walk according to this path.So, the overall system can be represented by:Wireless camera – computer – wireless connection for the mobile robot .The experimental work including some experiments shows that the developed mobile robot (pioneer p3-dx travels successfully from the start point and reach the goal point across the optimal path (according to time and power which is obtained as result of the proposed path planning algorithm introduced in this paper.

  17. Magneto-convective instabilities in horizontal cavities

    Science.gov (United States)

    Mistrangelo, Chiara; Bühler, Leo

    2016-02-01

    A linear stability analysis is performed to investigate the onset of convective motions in a flat cavity filled with liquid metal. A volumetric heat source is uniformly distributed in the fluid and a horizontal magnetic field is imposed. Walls perpendicular to the magnetic field are thermally insulating, and the top wall is isothermal and the bottom adiabatic. When a magnetic field is applied, electromagnetic forces tend to transform 3D convective flow structures into quasi-2D rolls aligned to the magnetic field. By integrating 3D equations along magnetic field lines, a quasi-2D mathematical model has been derived. A dissipation term in the 2D equations accounts for 3D viscous effects in boundary layers at Hartmann walls perpendicular to the magnetic field. The influence of various parameters on flow stability is investigated. The flow is stabilized by increasing the magnetic field intensity or the electric conductance of Hartmann walls and by reducing the aspect ratio of the cavity. Numerical simulations are performed to verify the analytical results and to describe the main convective flow patterns in the non-linear regime.

  18. Analysis of Near Horizontal Muons at HAWC

    Science.gov (United States)

    Barber, Ahron; HAWC Collaboration

    2017-01-01

    The HAWC (High Altitude Water Cherenkov) gamma ray observatory observes muons with nearly horizontal trajectories. HAWC is located at an altitude of 4100 meters a.s.l. on Sierra Negra in Mexico. The Gamma and Cosmic Ray detector is composed of 300 water tanks, 7.3 m in diameter and 4.5 m tall, spread over a physical area of 22,000 m2. Due to its thickness of 4.5 m, HAWC acts as a hodoscope capable of observing muons with trajectories at zenith angles greater than 75 degrees to just over 90 degrees. These muon trajectories have a unique signal in that they are linear and travel at nearly the speed of light. CORSIKA simulations indicate that these muons originate from high zenith angle cosmic ray events, where the air shower core is located at great distance from HAWC. I will present the angular distribution and rate at which HAWC observes these muon events. High Altitude Water Cherenkov Observatory.

  19. Horizontal Drop of 21- PWR Waste Package

    Energy Technology Data Exchange (ETDEWEB)

    A.K. Scheider

    2001-04-26

    The objective of this calculation is to determine the structural response of the waste package (WP) dropped horizontally from a specified height. The WP used for that purpose is the 21-Pressurized Water Reactor (PWR) WP. The scope of this document is limited to reporting the calculation results in terms of stress intensities. The information provided by the sketches (Attachment I) is that of the potential design of the type of WP considered in this calculation, and all obtained results are valid for that design only. This calculation is associated with the WP design and was performed by the Waste Package Design group in accordance with the ''Technical Work Plan for: Waste Package Design Description for LA'' (Ref. 16). AP-3.12Q, ''Calculations'' (Ref. 11) is used to perform the calculation and develop the document. The sketches attached to this calculation provide the potential dimensions and materials for the 21-PWR WP design.

  20. Yaw dynamics of horizontal axis wind turbines

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, A.C. (Utah Univ., Salt Lake City, UT (United States))

    1992-05-01

    Designers of a horizontal axis wind turbine yaw mechanism are faced with a difficult decision. They know that if they elect to use a yaw- controlled rotor then the system will suffer increased initial cost and increased inherent maintenance and reliability problems. On the other hand, if they elect to allow the rotor to freely yaw they known they will have to account for unknown and random, though bounded, yaw rates. They will have a higher-risk design to trade-off against the potential for cost savings and reliability improvement. The risk of a yaw-free system could be minimized if methods were available for analyzing and understanding yaw behavior. The complexity of yaw behavior has, until recently, discouraged engineers from developing a complete yaw analysis method. The objectives of this work are to (1) provide a fundamental understanding of free-yaw mechanics and the design concepts most effective at eliminating yaw problems, and (2) provide tested design tools and guidelines for use by free-yaw wind systems manufacturers. The emphasis is on developing practical and sufficiently accurate design methods.

  1. Horizontal plane head stabilization during locomotor tasks.

    Science.gov (United States)

    Cromwell, R L; Newton, R A; Carlton, L G

    2001-03-01

    Frequency characteristics of head stabilization were examined during locomotor tasks in healthy young adults(N = 8) who performed normal walking and 3 walking tasks designed to produce perturbations primarily in the horizontal plane. In the 3 walking tasks, the arms moved in phase with leg movement, with abnormally large amplitude, and at twice the frequency of leg movement. Head-in-space angular velocity was examined at the predominant frequencies of trunk motion. Head movements in space occurred at low frequencies ( 4.0 Hz) when the arms moved at twice the frequency of the legs. Head stabilization strategies were determined from head-on-trunk with respect to trunk frequency profiles derived from angular velocity data. During natural walking at low frequencies (head-on-trunk movement was less than trunk movement. At frequencies 3.0 Hz or greater, equal and opposite compensatory movement ensured head stability. When arm swing was altered, compensatory movement guaranteed head stability at all frequencies. Head stabilization was successful for frequencies up to 10.0 Hz during locomotor tasks. Maintaining head stability at high frequencies during voluntary tasks suggests that participants used feedforward mechanisms to coordinate head and trunk movements. Maintenance of head stability during dynamic tasks allows optimal conditions for vestibulo-ocular reflex function.

  2. Horizontal visibility graphs from integer sequences

    Science.gov (United States)

    Lacasa, Lucas

    2016-09-01

    The horizontal visibility graph (HVG) is a graph-theoretical representation of a time series and builds a bridge between dynamical systems and graph theory. In recent years this representation has been used to describe and theoretically compare different types of dynamics and has been applied to characterize empirical signals, by extracting topological features from the associated HVGs which have shown to be informative on the class of dynamics. Among some other measures, it has been shown that the degree distribution of these graphs is a very informative feature that encapsulates nontrivial information of the series's generative dynamics. In particular, the HVG associated to a bi-infinite real-valued series of independent and identically distributed random variables is a universal exponential law P(k)=(1/3){(2/3)}k-2, independent of the series marginal distribution. Most of the current applications have however only addressed real-valued time series, as no exact results are known for the topological properties of HVGs associated to integer-valued series. In this paper we explore this latter situation and address univariate time series where each variable can only take a finite number n of consecutive integer values. We are able to construct an explicit formula for the parametric degree distribution {P}n(k), which we prove to converge to the continuous case for large n and deviates otherwise. A few applications are then considered.

  3. The peculiar Horizontal Branch of NGC 2808

    CERN Document Server

    Dalessandro, E; Ferraro, F R; Cassisi, S; Lanzoni, B; Rood, R T; Pecci, F Fusi; Sabbi, E

    2010-01-01

    We present an accurate analysis of the peculiar Horizontal Branch (HB) of the massive Galactic globular cluster NGC 2808, based on high-resolution far-UV and optical images of the central region of the cluster obtained with HST. We confirm the multimodal distribution of stars along the HB: 4 sub-populations separated by gaps are distinguishable. The detailed comparison with suitable theoretical models showed that (i) it is not possible to reproduce the luminosity of the entire HB with a single helium abundance, while an appropriate modeling is possible for three HB groups by assuming different helium abundances in the range 0.24 < Y < 0.4 that are consistent with the multiple populations observed in the Main Sequence; (ii) canonical HB models are not able to properly match the observational properties of the stars populating the hottest end of the observed HB distribution, the so called "blue-hook region". These objects are probably "hot-flashers" , stars that peel off the red giant branch before reachi...

  4. Shallow water model for horizontal centrifugal casting

    Science.gov (United States)

    Boháček, J.; Kharicha, A.; Ludwig, A.; Wu, M.

    2012-07-01

    A numerical model was proposed to simulate the solidification process of an outer shell of work roll made by the horizontal centrifugal casting technique. Shallow water model was adopted to solve the 2D average flow dynamics of melt spreading and the average temperature distribution inside the centrifugal casting mould by considering the centrifugal force, Coriolis force, viscous force due to zero velocity on the mould wall, gravity, and energy transport by the flow. Additionally, a 1D sub-model was implemented to consider the heat transfer in the radial direction from the solidifying shell to the mould. The solidification front was tracked by fulfilling the Stefan condition. Radiative and convective heat losses were included from both, the free liquid surface and the outer wall of the mould. Several cases were simulated with the following assumed initial conditions: constant height of the liquid metal (10, 20, and 30 mm), uniform temperature of the free liquid surface (1755 K). The simulation results have shown that while the solidification front remained rather flat, the free surface was disturbed by waves. The amplitude of waves increased with the liquid height. Free surface waves diminished as the solidification proceeded.

  5. Speech disorders in students in Belo Horizonte.

    Science.gov (United States)

    Rabelo, Alessandra Terra Vasconcelos; Alves, Claudia Regina Lindgren; Goulart, Lúcia Maria H Figueiredo; Friche, Amélia Augusta de Lima; Lemos, Stela Maris Aguiar; Campos, Fernanda Rodrigues; Friche, Clarice Passos

    2011-12-01

    To describe speech disorders in students from 1st to 4th grades, and to investigate possible associations between these disorders and stomatognathic system and auditory processing disorders. Cross-sectional study with stratified random sample composed of 288 students, calculated based on an universe of 1,189 children enrolled in public schools from the area covered by a health center in Belo Horizonte. The median age was 8.9 years, and 49.7% were male. Assessment used a stomatognathic system protocol adapted from the Myofunctional Evaluation Guidelines, the Phonology task of the ABFW - Child Language Test, and a simplified auditory processing evaluation. Data were statistically analyzed. From the subjects studied, 31.9% had speech disorder. From these, 18% presented phonetic deviation, 9.7% phonological deviation, and 4.2% phonetic and phonological deviation. Linguistic variation was observed in 38.5% of the children. There was a higher proportion of children with phonetic deviation in 1st grade, and a higher proportion of children younger than 8 years old with both phonetic and phonological deviations. Phonetic deviation was associated to stomatognathic system disorder, and phonological deviation was associated to auditory processing disorder. The prevalence of speech disorders in 1st to 4th grade students is considered high. Moreover, these disorders are associated to other Speech-Language Pathology and Audiology alterations, which suggest that one disorder may be a consequence of the other, indicating the need for early diagnosis and intervention.

  6. Horizontal gene transfer in silkworm, Bombyx mori

    Directory of Open Access Journals (Sweden)

    Li Bin

    2011-05-01

    Full Text Available Abstract Background The domesticated silkworm, Bombyx mori, is the model insect for the order Lepidoptera, has economically important values, and has gained some representative behavioral characteristics compared to its wild ancestor. The genome of B. mori has been fully sequenced while function analysis of BmChi-h and BmSuc1 genes revealed that horizontal gene transfer (HGT maybe bestow a clear selective advantage to B. mori. However, the role of HGT in the evolutionary history of B. mori is largely unexplored. In this study, we compare the whole genome of B. mori with those of 382 prokaryotic and eukaryotic species to investigate the potential HGTs. Results Ten candidate HGT events were defined in B. mori by comprehensive sequence analysis using Maximum Likelihood and Bayesian method combining with EST checking. Phylogenetic analysis of the candidate HGT genes suggested that one HGT was plant-to- B. mori transfer while nine were bacteria-to- B. mori transfer. Furthermore, functional analysis based on expression, coexpression and related literature searching revealed that several HGT candidate genes have added important characters, such as resistance to pathogen, to B. mori. Conclusions Results from this study clearly demonstrated that HGTs play an important role in the evolution of B. mori although the number of HGT events in B. mori is in general smaller than those of microbes and other insects. In particular, interdomain HGTs in B. mori may give rise to functional, persistent, and possibly evolutionarily significant new genes.

  7. A note on the path interval distance.

    Science.gov (United States)

    Coons, Jane Ivy; Rusinko, Joseph

    2016-06-01

    The path interval distance accounts for global congruence between locally incongruent trees. We show that the path interval distance provides a lower bound for the nearest neighbor interchange distance. In contrast to the Robinson-Foulds distance, random pairs of trees are unlikely to be maximally distant from one another under the path interval distance. These features indicate that the path interval distance should play a role in phylogenomics where the comparison of trees on a fixed set of taxa is becoming increasingly important.

  8. Continuous-Discrete Path Integral Filtering

    Directory of Open Access Journals (Sweden)

    Bhashyam Balaji

    2009-08-01

    Full Text Available A summary of the relationship between the Langevin equation, Fokker-Planck-Kolmogorov forward equation (FPKfe and the Feynman path integral descriptions of stochastic processes relevant for the solution of the continuous-discrete filtering problem is provided in this paper. The practical utility of the path integral formula is demonstrated via some nontrivial examples. Specifically, it is shown that the simplest approximation of the path integral formula for the fundamental solution of the FPKfe can be applied to solve nonlinear continuous-discrete filtering problems quite accurately. The Dirac-Feynman path integral filtering algorithm is quite simple, and is suitable for real-time implementation.

  9. Cooperative path planning of unmanned aerial vehicles

    CERN Document Server

    Tsourdos, Antonios; Shanmugavel, Madhavan

    2010-01-01

    An invaluable addition to the literature on UAV guidance and cooperative control, Cooperative Path Planning of Unmanned Aerial Vehicles is a dedicated, practical guide to computational path planning for UAVs. One of the key issues facing future development of UAVs is path planning: it is vital that swarm UAVs/ MAVs can cooperate together in a coordinated manner, obeying a pre-planned course but able to react to their environment by communicating and cooperating. An optimized path is necessary in order to ensure a UAV completes its mission efficiently, safely, and successfully.

  10. Langevin equation path integral ground state.

    Science.gov (United States)

    Constable, Steve; Schmidt, Matthew; Ing, Christopher; Zeng, Tao; Roy, Pierre-Nicholas

    2013-08-15

    We propose a Langevin equation path integral ground state (LePIGS) approach for the calculation of ground state (zero temperature) properties of molecular systems. The approach is based on a modification of the finite temperature path integral Langevin equation (PILE) method (J. Chem. Phys. 2010, 133, 124104) to the case of open Feynman paths. Such open paths are necessary for a ground state formulation. We illustrate the applicability of the method using model systems and the weakly bound water-parahydrogen dimer. We show that the method can lead to converged zero point energies and structural properties.

  11. Techniques and applications of path integration

    CERN Document Server

    Schulman, L S

    2005-01-01

    A book of techniques and applications, this text defines the path integral and illustrates its uses by example. It is suitable for advanced undergraduates and graduate students in physics; its sole prerequisite is a first course in quantum mechanics. For applications requiring specialized knowledge, the author supplies background material.The first part of the book develops the techniques of path integration. Topics include probability amplitudes for paths and the correspondence limit for the path integral; vector potentials; the Ito integral and gauge transformations; free particle and quadra

  12. Ratio between vertical and horizontal mandibular range of motion

    NARCIS (Netherlands)

    Dijkstra, P.U.; Kropmans, T.J.B.; Stegenga, B; de Bont, L.G.M.

    1998-01-01

    Mandibular range of motion (ROM), vertical and horizontal, is often measured as a part of a diagnostic assessment of temporomandibular joint disorders. Ln the literature, a fixed ratio between the vertical and the horizontal ROM has been suggested, i.e. 4:1. The ratio is frequently used to predict t

  13. Horizontal drilling methods proven in three test wells

    Energy Technology Data Exchange (ETDEWEB)

    Dorel, M.

    1983-05-01

    The practice of drilling horizontally through a reservoir by deviating the wellbore 90/sup 0/ from vertical requires precise planning and sound engineering practices. This article takes a look at the operational, engineering and planning aspects of three successfully drilled drainholes. It also presents a field-tested horizontal well logging procedure that may help extend and improve this technology.

  14. Horizontal Coherence of Wave Forces on Vertical Wall Breakwaters

    DEFF Research Database (Denmark)

    Archetti, R.; Frigaard, Peter; Lamberti, A.

    2001-01-01

    of breaking waves for increasing wave height are estimated and compared with existing empirical formulae. The horizontal dimension of the breaker is investigated using two different methodologies: the first analyses the decreasing of the highest 1/250 force with increasing horizontal dimension of the caisson...

  15. Effects of Corrugated Temperature Sheets on Optical Propagation along Quasi-Horizontal Paths in the Stably Stratified Atmosphere

    Science.gov (United States)

    2015-12-11

    atmosphere, pioneered by Tatarskii and coworkers in the 1950s and 1960s (Tatarskii, 1961, 1971), continues to be the conceptual basis for progress in...various science and engineering disciplines, such as remote sensing of the optically clear atmosphere, astronomy, free- space optical communication...correlation function of AOA fluctuations obtained from two closely spaced , light-emitting diodes (LEDs). The first method relies on the time delay of the

  16. Horizontal electromagnetic casting of thin metal sheets

    Energy Technology Data Exchange (ETDEWEB)

    Hull, John R. (Hinsdale, IL); Lari, Robert J. (Aurora, IL); Praeg, Walter F. (Palos Park, IL); Turner, Larry R. (Naperville, IL)

    1988-01-01

    Thin metal sheets are cast by magnetically suspending molten metal deposited within a ferromagnetic yoke and between AC conducting coils and linearly displacing the magnetically levitated liquid metal while it is being cooled to form a solid metal sheet. Magnetic flux increases as the molten metal sheet moves downward and decreases as the molten metal sheet moves upward to stabilize the sheet and maintain it in equilibrium as it is linearly displaced and solidified by cooling gases. A conducting shield is electrically coupled to the molten metal sheet by means of either metal sheet engaging rollers or brushes on the solidified metal, and by means of an electrode in the vessel containing the molten metal thereby providing a return path for the eddy currents induced in the metal sheet by the AC coil generated magnetic flux. Variation in the geometry of the conducting shield allows the magnetic flux between the metal sheet and the conducting shield to be varied and the thickness in surface quality of the metal sheet to be controlled. Side guards provide lateral containment for the molten metal sheet and stabilize and shape the magnetic field while a leader sheet having electromagnetic characteristics similar to those of the metal sheet is used to start the casting process and precedes the molten metal sheet through the magnet and forms a continuous sheet therewith. The magnet may be either U-shaped with a single racetrack coil or may be rectangular with a pair of facing bedstead coils.

  17. Horizontal electromagnetic casting of thin metal sheets

    Energy Technology Data Exchange (ETDEWEB)

    Hull, John R. (Hinsdale, IL); Lari, Robert J. (Aurora, IL); Praeg, Walter F. (Palos Park, IL); Turner, Larry R. (Naperville, IL)

    1987-01-01

    Thin metal sheets are cast by magnetically suspending molten metal deposited within a ferromagnetic yoke and between AC conducting coils and linearly displacing the magnetically levitated liquid metal while it is being cooled to form a solid metal sheet. Magnetic flux increases as the molten metal sheet moves downward and decreases as the molten metal sheet moves upward to stabilize the sheet and maintain it in equilibrium as it is linearly displaced and solidified by cooling gases. A conducting shield is electrically coupled to the molten metal sheet by means of either metal sheet engaging rollers or brushes on the solidified metal, and by means of an electrode in the vessel containing the molten metal thereby providing a return path for the eddy currents induced in the metal sheet by the AC coil generated magnetic flux. Variation in the geometry of the conducting shield allows the magnetic flux between the metal sheet and the conducting shield to be varied and the thickness in surface quality of the metal sheet to be controlled. Side guards provide lateral containment for the molten metal sheet and stabilize and shape the magnetic field while a leader sheet having electromagnetic characteristics similar to those of the metal sheet is used to start the casting process and precedes the molten metal sheet through the magnet and forms a continuous sheet therewith. The magnet may be either U-shaped with a single racetrack coil or may be rectangular with a pair of facing bedstead coils.

  18. Steerable vertical to horizontal energy transducer for mobile robots

    Science.gov (United States)

    Spletzer, Barry L.; Fischer, Gary J.; Feddema, John T.

    2001-01-01

    The present invention provides a steerable vertical to horizontal energy transducer for mobile robots that less complex and requires less power than two degree of freedom tilt mechanisms. The present invention comprises an end effector that, when mounted with a hopping actuator, translates along axis (typically vertical) actuation into combined vertical and horizontal motion. The end effector, or foot, mounts with an end of the actuator that moves toward the support surface (typically a floor or the earth). The foot is shaped so that the first contact with the support surface is off the axis of the actuator. Off-axis contact with the support surface generates an on-axis force (typically resulting in vertical motion) and a moment orthogonal to the axis. The moment initiates a horizontal tumbling motion, and tilts the actuator so that its axis is oriented with a horizontal component and continued actuation generates both vertical and horizontal force.

  19. A horizontal well analysis from a view of its productivity

    Directory of Open Access Journals (Sweden)

    Lucia Sciranková

    2006-10-01

    Full Text Available The 1990s may become known in the oil field as the decade of the horizontal well. Horizontal wells can increase the production rate and the ultimate recovery, and can reduce the number of platforms on wells required to develop a reservoir.An empirical equation to calculate the inflow performance of two-phase flow for a vertical and a horizontal well in regime of dissolved gas presented by Vogel in 1968. His equation was based on the results of reservoir simulation. The created model whore result (output is the ratio of the productivity of a horizontal well to the productivity of a vertical well for a given area expressed by anumber of vertical wells the replaced by one horizontal well. The model is applied for a concrete ideological model.

  20. Horizontal crustal movement in Chinese mainland from 1999 to 2001

    Institute of Scientific and Technical Information of China (English)

    顾国华; 符养; 王武星

    2004-01-01

    The paper introduces the horizontal crustal movement obtained from GPS observations in the regional networks(including the basic network and the fiducial network) of the Crustal Movement Observation Network of China(CMONOC) carried out in 1999 and 2001. This paper is characterized by the acquisition of the horizontal dis-placement velocities during the period from 1999 to 2001 at the observation stations in the regional networks withdatum definition of a group of stable stations with small mutual displacements in east China. Based on the mostdetailed map of horizontal crustal movement in Chinese mainland, the division of blocks, their displacements anddeformations are studied. An approach to analysis of the intensity of the horizontal crustal deformation is proposed.The general characteristics of the recent horizontal crustal movement in Chinese mainland and that before theKunlunshan earthquake of M=8.1 on November 14, 2001 are analyzed.

  1. A simple model for the estimation of rain-induced attenuation along earth-space paths at millimeter wavelengths

    Science.gov (United States)

    Stutzman, W. L.; Dishman, W. K.

    1982-12-01

    A simple attenuation model (SAM) is presented for estimating rain-induced attenuation along an earth-space path. The rain model uses an effective spatial rain distribution which is uniform for low rain rates and which has an exponentially shaped horizontal rain profile for high rain rates. When compared to other models, the SAM performed well in the important region of low percentages of time, and had the lowest percent standard deviation of all percent time values tested.

  2. Simulations and scaling of horizontal convection

    Directory of Open Access Journals (Sweden)

    Mehmet ILIcak

    2012-05-01

    Full Text Available In this paper we describe the results of various numerical simulations of sideways or horizontal convection. Specifically, a two-dimensional Boussinesq fluid is both heated and cooled from its upper surface, but the walls and the bottom of the tank are insulating and have no flux of heat through them. We perform experiments with a range of Rayleigh numbers up to 1011, obtained by systematically reducing the diffusivity. We also explore the effects of a nonlinear equation of state and of a mechanical force imposed on the top surface at a fixed Rayleigh number. We find that, when there is no mechanical forcing, both the energy dissipation and the strength of the circulation itself monotonically fall with decreasing diffusivity. At Rayleigh numbers greater than 1010 the flow is unsteady; however, the eddying flow is still much weaker than the steady flow at smaller Rayleigh numbers. At high Rayleigh numbers, the stratification and the mean circulation are increasingly confined to a thin layer at the upper surface, with the layer thickness decreasing according to Ra−1/5. There is no evidence that the flow ever enters a regime that is independent of Rayleigh number. Using a nonlinear equation of state makes little difference to the flow phenomenology at a moderate Rayleigh number. The addition of an imposed stress at the upper surface makes a significant difference in the flow. A strong, energy-dissipating circulation can be maintained even at Ra = 109, and the stratification extends more deeply into the fluid than in the unstressed case. Overall, our results are consistent with the notion that in the absence of mechanical forcing a fluid that is heated and cooled from above cannot maintain a deep stratification or a strong sustained flow at high Rayleigh numbers, even if the interior flow is unsteady.

  3. Joint modeling of constrained path enumeration and path choice behavior: a semi-compensatory approach

    DEFF Research Database (Denmark)

    Kaplan, Sigal; Prato, Carlo Giacomo

    2010-01-01

    A behavioural and a modelling framework are proposed for representing route choice from a path set that satisfies travellers’ spatiotemporal constraints. Within the proposed framework, travellers’ master sets are constructed by path generation, consideration sets are delimited according to spatio...... constraints are related to travellers’ socio-economic characteristics and that path choice is related to minimizing time and avoiding congestion....

  4. Effect of Horizontal Vibration on the Interfacial Instability in a Horizontal Hele-Shaw Cell

    Directory of Open Access Journals (Sweden)

    Souhar M.

    2012-07-01

    Full Text Available The effect of periodic oscillations on the interfacial instability of two immiscible fluids, confined in a horizontal Hele-Shaw cell, is investigated. A linear stability analysis of the basic state leads to a periodic Mathieu oscillator corresponding to the amplitude of the interface. Then, the threshold of parametric instability of the interface is characterized by harmonic or subharmonic periodic solutions. We show that the relevant parameters that control the interface are the Bond number, density ratio, Weber number and amplitude and frequency of oscillations.

  5. White Noise Path Integrals in Stochastic Neurodynamics

    Science.gov (United States)

    Carpio-Bernido, M. Victoria; Bernido, Christopher C.

    2008-06-01

    The white noise path integral approach is used in stochastic modeling of neural activity, where the primary dynamical variables are the relative membrane potentials, while information on transmembrane ionic currents is contained in the drift coefficient. The white noise path integral allows a natural framework and can be evaluated explicitly to yield a closed form for the conditional probability density.

  6. Cost allocation in shortest path games

    NARCIS (Netherlands)

    Voorneveld, M.; Grahn, S.

    2001-01-01

    A class of cooperative games arising from shortest path problems is dened These shortest path games are shown to be totally balanced and allow a population monotonic allocation scheme Possible methods for obtaining core elements are indicated rst by relating to the allocation rules in taxation and b

  7. The Path of Carbon in Photosynthesis VI.

    Science.gov (United States)

    Calvin, M.

    1949-06-30

    This paper is a compilation of the essential results of our experimental work in the determination of the path of carbon in photosynthesis. There are discussions of the dark fixation of photosynthesis and methods of separation and identification including paper chromatography and radioautography. The definition of the path of carbon in photosynthesis by the distribution of radioactivity within the compounds is described.

  8. Collaborative path planning for a robotic wheelchair.

    Science.gov (United States)

    Zeng, Qiang; Teo, Chee Leong; Rebsamen, Brice; Burdet, Etienne

    2008-11-01

    Generating a path to guide a wheelchair's motion faces two challenges. First, the path is located in the human environment and that is usually unstructured and dynamic. Thus, it is difficult to generate a reliable map and plan paths on it by artificial intelligence. Second, the wheelchair, whose task is to carry a human user, should move on a smooth and comfortable path adapted to the user's intentions. To meet these challenges, we propose that the human operator and the robot interact to create and gradually improve a guide path. This paper introduces design tools to enable an intuitive interaction, and reports experiments performed with healthy subjects in order to investigate this collaborative path learning strategy. We analyzed features of the optimal paths and user evaluation in representative conditions. This was complemented by a questionnaire filled out by the subjects after the experiments. The results demonstrate the effectiveness of this approach, and show the utility and complementarity of the tools to design ergonomic guide paths.

  9. Path Minima Queries in Dynamic Weighted Trees

    DEFF Research Database (Denmark)

    Davoodi, Pooya; Brodal, Gerth Stølting; Satti, Srinivasa Rao

    2011-01-01

    In the path minima problem on a tree, each edge is assigned a weight and a query asks for the edge with minimum weight on a path between two nodes. For the dynamic version of the problem, where the edge weights can be updated, we give data structures that achieve optimal query time\\todo{what about...

  10. Multi-block and path modelling procedures

    DEFF Research Database (Denmark)

    Høskuldsson, Agnar

    2008-01-01

    The author has developed a unified theory of path and multi-block modelling of data. The data blocks are arranged in a directional path. Each data block can lead to one or more data blocks. It is assumed that there is given a collection of input data blocks. Each of them is supposed to describe one...

  11. Two Generations of Path Dependence in Economics?

    DEFF Research Database (Denmark)

    Madsen, Mogens Ove

    2010-01-01

    Even if there is no fully articulated and generally accepted theory of Path Dependence it has eagerly been taken up across a wide range of social sciences – primarily coming from economics. Path Dependence is most of all a metaphor that offers reason to believe, that some political, social...

  12. Adaptively Ubiquitous Learning in Campus Math Path

    Science.gov (United States)

    Shih, Shu-Chuan; Kuo, Bor-Chen; Liu, Yu-Lung

    2012-01-01

    The purposes of this study are to develop and evaluate the instructional model and learning system which integrate ubiquitous learning, computerized adaptive diagnostic testing system and campus math path learning. The researcher first creates a ubiquitous learning environment which is called "adaptive U-learning math path system". This…

  13. Graphic method for analyzing common path interferometers

    DEFF Research Database (Denmark)

    Glückstad, J.

    1998-01-01

    Common path interferometers are widely used for visualizing phase disturbances and fluid flows. They are attractive because of the inherent simplicity and robustness in the setup. A graphic method will be presented for analyzing and optimizing filter parameters in common path interferometers....

  14. Robot path planning using genetic algorithms

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Presents a strategy for soccer robot path planning using genetic algorithms for which, real number coding method is used, to overcome the defects of binary coding method, and the double crossover operation a dopted, to avoid the common defect of early convergence and converge faster than the standard genetic algo rithms concludes from simulation results that the method is effective for robot path planning.

  15. Consistent Partial Least Squares Path Modeling

    NARCIS (Netherlands)

    Dijkstra, Theo K.; Henseler, Jörg

    2015-01-01

    This paper resumes the discussion in information systems research on the use of partial least squares (PLS) path modeling and shows that the inconsistency of PLS path coefficient estimates in the case of reflective measurement can have adverse consequences for hypothesis testing. To remedy this, the

  16. Inked Careers: Tattooing Professional Paths

    Directory of Open Access Journals (Sweden)

    Gabriela DeLuca

    2016-12-01

    Full Text Available The concept of career has an interdisciplinary and historical constitution, which includes persons, groups, organizations and society. Given that, we aim to deepen the interactionist notion of career from the understanding of a deviant path, supported by a theory and a method appropriated to the cited call for interdisciplinary approaches. Dilemmas (Hughes, 1958 and conflicts (Hughes, 1937 emerged as important analytical categories. Although necessary, these two concepts were not sufficient to contemplate analyses in their entirety. For this reason we conceptualized a third possibility of controversy during a career: the inquiries. The study followed the Narrative method to analyze objective and subjective changes during a tattoo artist’s career through interviews and informal conversations carried out over 22 months. The discussion presents three main contributions. Theoretically, a new understanding of the concept of careers, linking past, present and future and the idea of non-linearity of experienced and envisioned careers. Methodologically, suggesting orientations for future career studies such as the use of turning points as a methodological tool and the investigation of deviant fields. Finally, our defense of the interactionist perspective as suitable for career studies, since it allows the investigation of deviant elements.

  17. Decision paths in complex tasks

    Science.gov (United States)

    Galanter, Eugene

    1991-01-01

    Complex real world action and its prediction and control has escaped analysis by the classical methods of psychological research. The reason is that psychologists have no procedures to parse complex tasks into their constituents. Where such a division can be made, based say on expert judgment, there is no natural scale to measure the positive or negative values of the components. Even if we could assign numbers to task parts, we lack rules i.e., a theory, to combine them into a total task representation. We compare here two plausible theories for the amalgamation of the value of task components. Both of these theories require a numerical representation of motivation, for motivation is the primary variable that guides choice and action in well-learned tasks. We address this problem of motivational quantification and performance prediction by developing psychophysical scales of the desireability or aversiveness of task components based on utility scaling methods (Galanter 1990). We modify methods used originally to scale sensory magnitudes (Stevens and Galanter 1957), and that have been applied recently to the measure of task 'workload' by Gopher and Braune (1984). Our modification uses utility comparison scaling techniques which avoid the unnecessary assumptions made by Gopher and Braune. Formula for the utility of complex tasks based on the theoretical models are used to predict decision and choice of alternate paths to the same goal.

  18. Precision Cleaning - Path to Premier

    Science.gov (United States)

    Mackler, Scott E.

    2008-01-01

    ITT Space Systems Division s new Precision Cleaning facility provides critical cleaning and packaging of aerospace flight hardware and optical payloads to meet customer performance requirements. The Precision Cleaning Path to Premier Project was a 2007 capital project and is a key element in the approved Premier Resource Management - Integrated Supply Chain Footprint Optimization Project. Formerly precision cleaning was located offsite in a leased building. A new facility equipped with modern precision cleaning equipment including advanced process analytical technology and improved capabilities was designed and built after outsourcing solutions were investigated and found lacking in ability to meet quality specifications and schedule needs. SSD cleans parts that can range in size from a single threaded fastener all the way up to large composite structures. Materials that can be processed include optics, composites, metals and various high performance coatings. We are required to provide verification to our customers that we have met their particulate and molecular cleanliness requirements and we have that analytical capability in this new facility. The new facility footprint is approximately half the size of the former leased operation and provides double the amount of throughput. Process improvements and new cleaning equipment are projected to increase 1st pass yield from 78% to 98% avoiding $300K+/yr in rework costs. Cost avoidance of $350K/yr will result from elimination of rent, IT services, transportation, and decreased utility costs. Savings due to reduced staff expected to net $4-500K/yr.

  19. Gerbertian paths for the Jubilee

    Science.gov (United States)

    Sigismondi, Costantino

    2015-04-01

    Gerbert before becoming Pope Sylvester II came several times in Rome, as reported in his Letters and in the biography of Richerus. Eight places in Rome can be connected with Gerbertian memories. 1. The Cathedral of St. John in the Lateran where the gravestone of his tumb is still preserved near the Holy Door; 2. the “Basilica Hierusalem” (Santa Croce) where Gerbert had the stroke on May 3rd 1003 which lead him to death on May 12th; 3. the Aventine hill, with the church of the Knights of Malta in the place where the palace of the Ottonian Emperors was located; 4. the church of St. Bartholomew in the Tiber Island built in 997 under Otto III; 5. the Obelisk of Augustus in Montecitorio to remember the relationship between Gerbert, Astronomy and numbers which led the birth of the legends on Gerbert magician; 6. St. Mary Major end of the procession of August 15, 1000; 7. St. Paul outside the walls with the iconography of the Popes and 8. St. Peter's tumb end of all Romaei pilgrimages. This Gerbertian path in Rome suggests one way to accomplish the pilgrimage suggested by Pope Francis in the Bulla Misericordiae Vultus (14) of indiction of the new Jubilee.

  20. Feynman Path Integrals Over Entangled States

    CERN Document Server

    Green, A G; Keeling, J; Simon, S H

    2016-01-01

    The saddle points of a conventional Feynman path integral are not entangled, since they comprise a sequence of classical field configurations. We combine insights from field theory and tensor networks by constructing a Feynman path integral over a sequence of matrix product states. The paths that dominate this path integral include some degree of entanglement. This new feature allows several insights and applications: i. A Ginzburg-Landau description of deconfined phase transitions. ii. The emergence of new classical collective variables in states that are not adiabatically continuous with product states. iii. Features that are captured in product-state field theories by proliferation of instantons are encoded in perturbative fluctuations about entangled saddles. We develop a general formalism for such path integrals and a couple of simple examples to illustrate their utility.

  1. Critical Review of Path Integral Formulation

    CERN Document Server

    Fujita, Takehisa

    2008-01-01

    The path integral formulation in quantum mechanics corresponds to the first quantization since it is just to rewrite the quantum mechanical amplitude into many dimensional integrations over discretized coordinates $x_n$. However, the path integral expression cannot be connected to the dynamics of classical mechanics, even though, superficially, there is some similarity between them. Further, the field theory path integral in terms of many dimensional integrations over fields does not correspond to the field quantization. We clarify the essential difference between Feynman's original formulation of path integral in QED and the modern version of the path integral method prevailing in lattice field theory calculations, and show that the former can make a correct second quantization while the latter cannot quantize fields at all and its physical meaning is unknown.

  2. Accounting for the effect of horizontal gradients in limb measurements of scattered sunlight

    Directory of Open Access Journals (Sweden)

    J. Puķīte

    2008-06-01

    Full Text Available Limb measurements provided by the SCanning Imaging Absorption spectrometer for Atmospheric CHartographY (SCIAMACHY on the ENVISAT satellite allow retrieving stratospheric profiles of various trace gases on a global scale, among them BrO for the first time. For limb observations in the UV/VIS spectral region the instrument measures scattered light with a complex distribution of light paths: the light is measured at different tangent heights and can be scattered or absorbed in the atmosphere or reflected by the ground. By means of spectroscopy and radiative transfer modelling these measurements can be inverted to retrieve the vertical distribution of stratospheric trace gases.

    The fully spherical 3-D Monte Carlo radiative transfer model "Tracy-II" is applied in this study. The Monte Carlo method benefits from conceptual simplicity and allows realizing the concept of full spherical geometry of the atmosphere and also its 3-D properties, which is important for a realistic description of the limb geometry. Furthermore it allows accounting for horizontal gradients in the distribution of trace gases.

    In this study the effect of horizontally inhomogeneous distributions of trace gases along flight/viewing direction on the retrieval of profiles is investigated. We introduce a tomographic method to correct for this effect by combining consecutive limb scanning sequences and utilizing the overlap in their measurement sensitivity regions. It is found that if horizontal inhomogenity is not properly accounted for, typical errors of 20% for NO2 and up to 50% for OClO around the altitude of the profile peak can arise for measurements close to the Arctic polar vortex boundary in boreal winter.

  3. Horizontal gene transfer from Agrobacterium to plants

    Directory of Open Access Journals (Sweden)

    Tatiana V. Matveeva

    2014-08-01

    Full Text Available Most genetic engineering of plants uses Agrobacterium mediated transformation to introduce novel gene content. In nature, insertion of T-DNA in the plant genome and its subsequent transfer via sexual reproduction has been shown in several species in the genera Nicotiana and Linaria. In these natural examples of horizontal gene transfer from Agrobacterium to plants, the T-DNA donor is assumed to be a mikimopine strain of A.rhizogenes. A sequence homologous to the T-DNA of the Ri plasmid of Agrobacterium rhizogenes was found in the genome of untransformed Nicotiana glauca about 30 years ago, and was named cellular T-DNA (cT-DNA. It represents an imperfect inverted repeat and contains homologues of several T-DNA oncogenes (NgrolB, NgrolC, NgORF13, NgORF14 and an opine synthesis gene (Ngmis. A similar cT-DNA has also been found in other species of the genus Nicotiana. These presumably ancient homologues of T-DNA genes are still expressed, indicating that they may play a role in the evolution of these plants. Recently T-DNA has been detected and characterized in Linaria vulgaris and L. dalmatica. In Linaria vulgaris the cT-DNA is present in two copies and organized as a tandem imperfect direct repeat, containing LvORF2, LvORF3, LvORF8, LvrolA, LvrolB, LvrolC, LvORF13, LvORF14, and the Lvmis genes. All L. vulgaris and L. dalmatica plants screened contained the same T-DNA oncogenes and the mis gene. Evidence suggests that there were several independent T-DNA integration events into the genomes of these plant genera. We speculate that ancient plants transformed by A. rhizogenes might have acquired a selective advantage in competition with the parental species. Thus, the events of T-DNA insertion in the plant genome might have affected their evolution, resulting in the creation of new plant species. In this review we focus on the structure and functions of cT-DNA in Linaria and Nicotiana and discuss their possible evolutionary role.

  4. Horizontal versus familial transmission of Helicobacter pylori.

    Directory of Open Access Journals (Sweden)

    Sandra Schwarz

    2008-10-01

    Full Text Available Transmission of Helicobacter pylori is thought to occur mainly during childhood, and predominantly within families. However, due to the difficulty of obtaining H. pylori isolates from large population samples and to the extensive genetic diversity between isolates, the transmission and spread of H. pylori remain poorly understood. We studied the genetic relationships of H. pylori isolated from 52 individuals of two large families living in a rural community in South Africa and from 43 individuals of 11 families living in urban settings in the United Kingdom, the United States, Korea, and Colombia. A 3,406 bp multilocus sequence haplotype was determined for a total of 142 H. pylori isolates. Isolates were assigned to biogeographic populations, and recent transmission was measured as the occurrence of non-unique isolates, i.e., isolates whose sequences were identical to those of other isolates. Members of urban families were almost always infected with isolates from the biogeographic population that is common in their location. Non-unique isolates were frequent in urban families, consistent with familial transmission between parents and children or between siblings. In contrast, the diversity of H. pylori in the South African families was much more extensive, and four distinct biogeographic populations circulated in this area. Non-unique isolates were less frequent in South African families, and there was no significant correlation between kinship and similarity of H. pylori sequences. However, individuals who lived in the same household did have an increased probability of carrying the same non-unique isolates of H. pylori, independent of kinship. We conclude that patterns of spread of H. pylori under conditions of high prevalence, such as the rural South African families, differ from those in developed countries. Horizontal transmission occurs frequently between persons who do not belong to a core family, blurring the pattern of familial

  5. How can horizontal wells help in naturally fractured reservoir characterization?

    Energy Technology Data Exchange (ETDEWEB)

    Mazouzi, A.; Deghmoum, A.; Azzouguen, A. [Sonatrach Inc., Hydra (Algeria); Oudjida, A. [Anadarko Inc., (Algeria)

    2000-11-01

    Two successfully drilled horizontal gas wells in the Tin Fouye Tabankort (TFT) fractured reservoir in Algeria were described. The productivity index of horizontal wells compared to vertical wells depends on the pay zone height, vertical anisotropy, lateral anisotropy, the length of the horizontal drain and the amplitude of the damaged zone. Transient tests in horizontal wells can solve the problem of quantifying the vertical and lateral anisotropies. Horizontal wells also minimize the turbulence effects in the vicinity of the wellbore, particularly in gas wells. The two horizontal wells in the TFT reservoir provide an important gas flow rate. The productivity index for each well is triple that of a vertical well. The permeability tensor on the TFT reservoir is established on the basis of transient test reconstitution using numerical simulation. The vertical permeability yields the best match for pressure response. It can be shown as a translation effect in time at the beginning of the linear flow regime. The horizontal anisotropy reacts to the translation of pressure and its derivative in the vertical direction. The configuration of the reservoir shows a high lateral anisotropy with regards to permeability. The vertical permeability can be considered as the composite permeability of both the matrix and fractures. Numerical and laboratory studies show that low permeability is due to fracture opening. Therefore, fracture doesn't necessarily enhance permeability. 8 refs., 3 tabs., 13 figs.

  6. Path Following Control of an AUV under the Current Using the SVR-ADRC

    Directory of Open Access Journals (Sweden)

    Zheping Yan

    2014-01-01

    Full Text Available A novel active disturbance rejection control (ADRC controller is proposed based on support vector regression (SVR. The SVR-ADRC is designed to force an underactuated autonomous underwater vehicle (AUV to follow a path in the horizontal plane with the ocean current disturbance. It is derived using SVR algorithm to adjust the coefficients of the nonlinear state error feedback (ELSEF part in ADRC to deal with nonlinear variations at different operating points. The trend of change about ELSEF coefficients in the simulation proves that the designed SVR algorithm maintains the characteristics of astringency and stability. Furthermore, the path following errors under current in simulation has proved the high accuracy, strong robustness, and stability of the proposed SVR-ADRC. The contributions of the proposed controller are to improve the characteristics of ADRC considering the changing parameters in operating environment which make the controller more adaptive for the situation.

  7. The development and psychometric testing of the horizontal violence scale.

    Science.gov (United States)

    Longo, Joy; Newman, David

    2014-12-01

    Inappropriate behaviors of healthcare workers can threaten the delivery of safe, quality care. The purpose of this research was to develop a research instrument specific to the construct of horizontal violence and conduct foundational psychometric testing of the newly developed instrument. The overall findings on the fit indices suggest that this model does adequately measure the underlying construct of horizontal violence. The instrument can be used as a way to determine the existence and extent of horizontal violence in practice settings and used to augment the study of the work environment, particularly in relation to healthy work environments.

  8. MWD resistivity tool guides bit horizontally in thin bed

    Energy Technology Data Exchange (ETDEWEB)

    Fagin, R.A. (Teleco Oilfield Services, Inc., Houston, TX (US))

    1991-12-09

    This paper reports on the MWD dual processing resistivity (DPR) measurements and modelling which helped steer a horizontal well through a thin oil zone to avoid a nearby oil/water contact. The horizontal well came on-line flowing 380 bo/d with no water production. Offset vertical wells produce an average of 33 bo/d with an 83% saltwater cut. Until recently, horizontal drilling efforts have been focused on thick reservoirs in which the stratigraphic position of the well bore within the target formation was not critical. Navigation through much thinner reservoirs is now possible with a technique that uses an electromagnetic propagation resistivity tool.

  9. A selection method of the horizontal wells completion

    Directory of Open Access Journals (Sweden)

    Ivica Ristović

    2006-10-01

    Full Text Available The completion of horizontal wells can be done by different ways and depends on production constraints and the reservoir characteristics.The selection of a completon method is directly influenced by the degree of rock consolidation, the need for water or gas shut off,the anticipated flow rate, the completion longevity, the shale reactivity and the stability, the degree of grain sorting and the lamination.In this article, the possible methods for the horizontal well completion are shown. Also, it is presented the horizontal well completion selection flowchart. This algorithm is made on the basis of a large number of wells’ analysis considering reservoir characteristics and production constraints.

  10. Evaluation of Parameters Affecting Horizontal Stability of Landing Mats

    Science.gov (United States)

    1976-09-01

    1974. A rmathematical 11aodel tio silluatet the buckling response oif thte tria’i to th;: hora /ttntal ltAds way, atso elp. 1 h reuls o th...NO. 19R-20-0 MAT XU19, 4-FT X 4*PT ZERO ECCENTRICITY WIT420T EJGH48F NOTE NUMBERS SL LINES .RE HORIZONTAL FORC~E (LEFT) AND HORIZONTAL MOVEMENT ,RIGH...connector bars 14- TEST NO. 19-20-0 MAT XM19, 4-FT X 4-FT WIDTH 20-FT, LENGTH 48-FT ZERO ECCENTRICITY S-NG NUMBERS BYLINES ARE HORIZONTAL FORCE (LEFT) AND

  11. Reaction path synthesis methodology for waste minimization

    Institute of Scientific and Technical Information of China (English)

    HU; Shanying; LI; Mingheng; LI; Yourun; SHEN; Jingzhu; LIU

    2004-01-01

    It is a key step for reducing waste generation in chemical processes to design optimal reaction paths. In this paper, methods of waste minimization for reaction path synthesis problems are proposed to realize eco-industrial production mode with minimum waste emission. A new conception of simple stoichiometric reaction is presented for reaction path synthesis problem. All simple stoichiometric reactions can be obtained by mathematical transformation for atom matrix of a reaction system. Based on the conception, a two-tier optimization method for complex reaction path synthesis problems is addressed. The first step is to determine the economic optimal overall reactions, and the second step to decompose each overall reaction into several sub-reactions and find out the best thermodynamic feasible reaction path. Further, a method of reaction path synthesis with waste closed-cycle is proposed based on simple stoichiometric reactions for achieving zero waste emission to poly-generation problem of multi-products. Case studies show that the proposed methods can efficiently solve practical reaction path synthesis problems.

  12. Robot path planning using a genetic algorithm

    Science.gov (United States)

    Cleghorn, Timothy F.; Baffes, Paul T.; Wang, Liu

    1988-01-01

    Robot path planning can refer either to a mobile vehicle such as a Mars Rover, or to an end effector on an arm moving through a cluttered workspace. In both instances there may exist many solutions, some of which are better than others, either in terms of distance traversed, energy expended, or joint angle or reach capabilities. A path planning program has been developed based upon a genetic algorithm. This program assumes global knowledge of the terrain or workspace, and provides a family of good paths between the initial and final points. Initially, a set of valid random paths are constructed. Successive generations of valid paths are obtained using one of several possible reproduction strategies similar to those found in biological communities. A fitness function is defined to describe the goodness of the path, in this case including length, slope, and obstacle avoidance considerations. It was found that with some reproduction strategies, the average value of the fitness function improved for successive generations, and that by saving the best paths of each generation, one could quite rapidly obtain a collection of good candidate solutions.

  13. Nonholonomic catheter path reconstruction using electromagnetic tracking

    Science.gov (United States)

    Lugez, Elodie; Sadjadi, Hossein; Akl, Selim G.; Fichtinger, Gabor

    2015-03-01

    Catheter path reconstruction is a necessary step in many clinical procedures, such as cardiovascular interventions and high-dose-rate brachytherapy. To overcome limitations of standard imaging modalities, electromagnetic tracking has been employed to reconstruct catheter paths. However, tracking errors pose a challenge in accurate path reconstructions. We address this challenge by means of a filtering technique incorporating the electromagnetic measurements with the nonholonomic motion constraints of the sensor inside a catheter. The nonholonomic motion model of the sensor within the catheter and the electromagnetic measurement data were integrated using an extended Kalman filter. The performance of our proposed approach was experimentally evaluated using the Ascension's 3D Guidance trakStar electromagnetic tracker. Sensor measurements were recorded during insertions of an electromagnetic sensor (model 55) along ten predefined ground truth paths. Our method was implemented in MATLAB and applied to the measurement data. Our reconstruction results were compared to raw measurements as well as filtered measurements provided by the manufacturer. The mean of the root-mean-square (RMS) errors along the ten paths was 3.7 mm for the raw measurements, and 3.3 mm with manufacturer's filters. Our approach effectively reduced the mean RMS error to 2.7 mm. Compared to other filtering methods, our approach successfully improved the path reconstruction accuracy by exploiting the sensor's nonholonomic motion constraints in its formulation. Our approach seems promising for a variety of clinical procedures involving reconstruction of a catheter path.

  14. How the Learning Path and the Very Structure of a Multifloored Environment Influence Human Spatial Memory.

    Science.gov (United States)

    Dollé, Laurent; Droulez, Jacques; Bennequin, Daniel; Berthoz, Alain; Thibault, Guillaume

    2015-01-01

    Few studies have explored how humans memorize landmarks in complex multifloored buildings. They have observed that participants memorize an environment either by floors or by vertical columns, influenced by the learning path. However, the influence of the building's actual structure is not yet known. In order to investigate this influence, we conducted an experiment using an object-in-place protocol in a cylindrical building to contrast with previous experiments which used rectilinear environments. Two groups of 15 participants were taken on a tour with a first person perspective through a virtual cylindrical three-floored building. They followed either a route discovering floors one at a time, or a route discovering columns (by simulated lifts across floors). They then underwent a series of trials, in which they viewed a camera movement reproducing either a segment of the learning path (familiar trials), or performing a shortcut relative to the learning trajectory (novel trials). We observed that regardless of the learning path, participants better memorized the building by floors, and only participants who had discovered the building by columns also memorized it by columns. This expands on previous results obtained in a rectilinear building, where the learning path favoured the memory of its horizontal and vertical layout. Taken together, these results suggest that both learning mode and an environment's structure influence the spatial memory of complex multifloored buildings.

  15. Fluctuating paths and fields Festschrift Kleinert (Hagen)

    CERN Document Server

    Bachmann, M; Schmidt, H J; Janke, W

    2001-01-01

    This volume covers the following fields: path integrals, quantum field theory, variational perturbation theory, phase transitions and critical phenomena, topological defects, strings and membranes, gravitation and cosmology. Contents: Path Integrals and Quantum Mechanics: Semiclassical Quantum Mechanics: A Path-Integral Approach (B R Holstein); Conjecture on the Reality of Spectra of Non-Hermitian Hamiltonians (C M Bender et al.); Time-Transformation Approach to q -Deformed Objects (A Inomata); Characterizing Volume Forms (P Cartier et al.); Vassiliev Invariants and Functional Integration (L H

  16. Path integral representations on the complex sphere

    Energy Technology Data Exchange (ETDEWEB)

    Grosche, C. [Hamburg Univ. (Germany). 2. Inst. fuer Theoretische Physik

    2007-08-15

    In this paper we discuss the path integral representations for the coordinate systems on the complex sphere S{sub 3C}. The Schroedinger equation, respectively the path integral, separates in exactly 21 orthogonal coordinate systems. We enumerate these coordinate systems and we are able to present the path integral representations explicitly in the majority of the cases. In each solution the expansion into the wave-functions is stated. Also, the kernel and the corresponding Green function can be stated in closed form in terms of the invariant distance on the sphere, respectively on the hyperboloid. (orig.)

  17. Non Abelian Dual Maps in Path Space

    CERN Document Server

    Martin, I

    1999-01-01

    We study an extension of the procedure to construct duality transformations among abelian gauge theories to the non abelian case using a path space formulation. We define a pre-dual functional in path space and introduce a particular non local map among Lie algebra valued 1-form functionals that reduces to the ordinary Hodge-* duality map of the abelian theories. Further, we establish a full set of equations on path space representing the ordinary Yang Mills equations and Bianchi identities of non abelian gauge theories of 4-dimensional euclidean space.

  18. Extending the application of critical path methods.

    Science.gov (United States)

    Coffey, R J; Othman, J E; Walters, J I

    1995-01-01

    Most health care organizations are using critical pathways in an attempt to reduce the variation in patient care, improve quality, enhance communication, and reduce costs. Virtually all of the critical path efforts to date have developed tables of treatments, medications, and so forth by day and have displayed them in a format known as a Gantt chart. This article presents a methodology for identifying the true "time-limiting" critical path, describes three additional methods for presenting the information--the network, precedent, and resource formats--and shows how these can significantly enhance current critical path efforts.

  19. INVESTMENT DEVELOPMENT PATH – CONCEPT AND TERMS

    Directory of Open Access Journals (Sweden)

    Ovidiu Serafim TRUFIN

    2015-04-01

    Full Text Available This article aims to analyze and explain the traditional model of Investment Development Path with new teoretical approaches. Investment Develoment Path is the latest theory about foreign direct investment and explains the relationship between a country’s development level and international investment position of a country. It has become a necessity in this research field of Romanian economy to establish a idiosyncratic model for evolution of inflows and outflows of Foreign Direct Investments after 1990. Also, persistent confusion between static and dynamic nature in using appropriate economic Romanian terms is removed. General theoretical approach is enhanced with new elements of schematic theorizing of Stages of Investment Development Path.

  20. Rotational path removable partial denture design.

    Science.gov (United States)

    Jacobson, T E; Krol, A J

    1982-10-01

    A detailed description of a rotational path of insertion design for removable partial dentures has been presented. By minimizing the use of conventional clasps, this technique offers some advantages. Rotational path designs may minimize adverse periodontal response to a removable partial denture by reducing plaque accumulation and may be applied in esthetically demanding situations. The design concept involves the use of rigid retentive components that gain access to undercut areas through a rotational path of insertion. These rigid components satisfy the basic requirements of conventional direct retained design.

  1. Quantum Adiabatic Evolution Algorithms with Different Paths

    CERN Document Server

    Farhi, E; Gutmann, S; Farhi, Edward; Goldstone, Jeffrey; Gutmann, Sam

    2002-01-01

    In quantum adiabatic evolution algorithms, the quantum computer follows the ground state of a slowly varying Hamiltonian. The ground state of the initial Hamiltonian is easy to construct; the ground state of the final Hamiltonian encodes the solution of the computational problem. These algorithms have generally been studied in the case where the "straight line" path from initial to final Hamiltonian is taken. But there is no reason not to try paths involving terms that are not linear combinations of the initial and final Hamiltonians. We give several proposals for randomly generating new paths. Using one of these proposals, we convert an algorithmic failure into a success.

  2. Test Derivation Through Critical Path Transitions

    Institute of Scientific and Technical Information of China (English)

    李卫东; 魏道政

    1992-01-01

    In this paper, a new technique called test derivation is presented,aiming at the promotion of the random testing efficiency for combinational circuits,Combined with a fault simulator based on critical path tracing method,we introduce the concept of seed test derivation and attempt to generate a group of new tests from the seed test by means of critical path transition.The neccessary conditions and efficient algorithms are proposed to guarantee the usefulness of the newly derived tests and the correctness of the critical path transitions.Also,examples are given to demonstrate the effectiveness of the technique.

  3. Heat transfer to near-critical helium in horizontal channels

    Energy Technology Data Exchange (ETDEWEB)

    Dolgoy, M.L.; Kirichenko, Y.A.; Sklovsky, Y.B.; Troyanov, A.M.; Chernyakov, P.S. (AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur)

    1983-03-01

    Experimental results on heat transfer and pressure losses during a forced motion of helium of near-critical state parameters in a horizontal channel are reported. A method of calculation of temperature and pressure distributions along the channel is proposed.

  4. Vertical Array in Space for Horizontal Air-Showers

    CERN Document Server

    Fargion, D

    2009-01-01

    We consider the guaranteed physics of horizontal (hadron) air-showers, HAS, developing at high (tens km) altitudes. Their morphology and information traces are different from vertical ones. Hundreds of km long HAS are often split by geomagnetic fields in a long (fan-like) showering with a twin spiral tail. The horizontal fan-like airshowers are really tangent and horizontal only at North and South poles. At different latitude these showering plane are turned and inclined by geomagnetic fields. In particular at magnetic equator such tangent horizontal East-West airshowers are bent and developed into a vertical fan air-shower, easily detectable by a vertical array detector (hanging elements by gravity). Such "medusa" arrays maybe composed by inflated floating balloons chains. The light gas float and it acts as an calorimeter for the particles, while it partially sustains the detector weight. Vertically hanging chains as well as rubber doughnut balloons (whose interior may record Cherenkov lights) reveal bundles...

  5. Determination of Elastic Twist in Horizontal Axis Wind Turbines (HAWTs)

    Energy Technology Data Exchange (ETDEWEB)

    Stoddard, F.; Nelson, V.; Starcher, K.; Andrews, B.

    2006-06-01

    This report presents the results of a project at the Alternative Energy Institute (AEI) which measured and calculated the elastic twist of three representative composite horizontal-axis blades: Carter 300, Gougeon ESI 54, and UTRC 8 kW.

  6. Horizontal Bulk Material Pressure in Silo Subjected to Impulsive Load

    Directory of Open Access Journals (Sweden)

    Radosław Tatko

    2008-01-01

    Full Text Available This paper describes laboratory tests carried out in the steel flat-bottomed silo model filled with sand, subjected to external dynamic loads. The model was placed on a system of springs, which represent subsoil. The loads in the form of horizontal impulses were applied to the bottom plate of the silo. Horizontal pressure-time courses were used to analyze the influence of subsoil vibrations on the distribution changes of these pressures. Basic conclusion: (1 the subsoil vibrations cause two types of changes of the horizontal pressures: stable changes which are observed when the model vibrations finish and cyclic of short duration (brief changes; (2 the subsoil vibrations either generate stable increase or stable decrease of the pressures from before vibrations or do not generate any essential stable change; (3 the cyclic dynamic changes of the horizontal pressures depend on the direction of the silo wall displacements and they are the function of the values of these displacements.

  7. Nurse Against Nurse: Horizontal Bullying in the Nursing Profession.

    Science.gov (United States)

    Granstra, Katherine

    2015-01-01

    Healthcare professionals are not immune to bullying; in fact, they experience bullying at an alarming rate. Sometimes the bullying is passed down from superiors, but frequently bullying occurs between coworkers. This is known as "horizontal bullying," and it has become a serious issue within the nursing profession. Horizontal bullying between nurses can cause negative consequences for everyone involved, in particular the nurses, patients, and the entire organization. To fully address and resolve horizontal bullying in the nursing profession, we must consider many factors. The first step is to establish what constitutes bullying and to develop a clear process for dealing with it when it occurs. Before it is possible to eliminate the problem, we need to understand why bullying takes place. To be effective, solutions to the problem of horizontal bullying in the nursing profession must include the entire healthcare industry.

  8. Optimizing of Culture Condition in Horizontal Rotating Bioreactor

    Institute of Scientific and Technical Information of China (English)

    Yan-Fang ZHANG; Huai-Qing CHEN; Hua HUANG

    2005-01-01

    @@ 1 Introduction Bioreactor is the most important equipment in tissue engineering. It can mimic the micro-environment of cell growth in vitro. At present, horizontal rotating bioreactor is the most advanced equipment for cell culture in the world.

  9. Horizontal Branch stars as AmFm/HgMn stars

    CERN Document Server

    Michaud, G

    2008-01-01

    Recent observations and models for horizontal branch stars are briefly described and compared to models for AmFm stars. The limitations of those models are emphasized by a comparison to observations and models for HgMn stars.

  10. Regulation of mammalian horizontal gene transfer by apoptotic DNA fragmentation

    Science.gov (United States)

    Yan, B; Wang, H; Li, F; Li, C-Y

    2006-01-01

    Previously it was shown that horizontal DNA transfer between mammalian cells can occur through the uptake of apoptotic bodies, where genes from the apoptotic cells were transferred to neighbouring cells phagocytosing the apoptotic bodies. The regulation of this process is poorly understood. It was shown that the ability of cells as recipient of horizontally transferred DNA was enhanced by deficiency of p53 or p21. However, little is known with regard to the regulation of DNA from donor apoptotic cells. Here we report that the DNA fragmentation factor/caspase-activated DNase (DFF/CAD), which is the endonuclease responsible for DNA fragmentation during apoptosis, plays a significant role in regulation of horizontal DNA transfer. Cells with inhibited DFF/CAD function are poor donors for horizontal gene transfer (HGT) while their ability of being recipients of HGT is not affected. PMID:17146478

  11. Horizontal Bulk Material Pressure in Silo Subjected to Impulsive Load

    OpenAIRE

    Radosław Tatko; Sylwester Kobielak

    2008-01-01

    This paper describes laboratory tests carried out in the steel flat-bottomed silo model filled with sand, subjected to external dynamic loads. The model was placed on a system of springs, which represent subsoil. The loads in the form of horizontal impulses were applied to the bottom plate of the silo. Horizontal pressure-time courses were used to analyze the influence of subsoil vibrations on the distribution changes of these pressures. Basic conclusion: (1) the subsoil vibrations cause two ...

  12. Horizontal gaze palsy with progressive scoliosis: CT and MR findings

    Energy Technology Data Exchange (ETDEWEB)

    Bomfim, Rodrigo C.; Tavora, Daniel G.F.; Nakayama, Mauro; Gama, Romulo L. [Sarah Network of Rehabilitation Hospitals, Department of Radiology, Ceara (Brazil)

    2009-02-15

    Horizontal gaze palsy with progressive scoliosis (HGPPS) is a rare congenital disorder characterized by absence of conjugate horizontal eye movements and progressive scoliosis developing in childhood and adolescence. We present a child with clinical and neuroimaging findings typical of HGPPS. CT and MRI of the brain demonstrated pons hypoplasia, absence of the facial colliculi, butterfly configuration of the medulla and a deep midline pontine cleft. We briefly discuss the imaging aspects of this rare entity in light of the current literature. (orig.)

  13. Equilibrium type of competition with horizontal product innovation

    OpenAIRE

    Negriu, A.

    2015-01-01

    Singh and Vives (1984) consider a game where duopolists first commit to a strategic variable quantity or pice, and then compete in selling horizontally differentiated products. Here product substitutability is endogenized by allowing firms to undertake R&D investments to increase differentitation. Whereas in the original model Cournot competition always ensued in equilibrium, horizontal product innovation allows all types of market competition to be an equilibrium, depending on model paramete...

  14. Mapping Proprioception across a 2D Horizontal Workspace

    OpenAIRE

    2010-01-01

    Relatively few studies have been reported that document how proprioception varies across the workspace of the human arm. Here we examined proprioceptive function across a horizontal planar workspace, using a new method that avoids active movement and interactions with other sensory modalities. We systematically mapped both proprioceptive acuity (sensitivity to hand position change) and bias (perceived location of the hand), across a horizontal-plane 2D workspace. Proprioception of both the le...

  15. International transferability of accident modification functions for horizontal curves.

    Science.gov (United States)

    Elvik, Rune

    2013-10-01

    Studies of the relationship between characteristics of horizontal curves and accident rate have been reported in several countries. The characteristic most often studied is the radius of a horizontal curve. Functions describing the relationship between the radius of horizontal curves and accident rate have been developed in Australia, Canada, Denmark, Germany, Great Britain, New Zealand, Norway, Portugal, Sweden, and the United States. Other characteristics of horizontal curves that have been studied include deflection angle, curve length, the presence of transition curves, super-elevation in curves and distance to adjacent curves. This paper assesses the international transferability of mathematical functions (accident modification functions) that have been developed to relate the radius of horizontal curves to their accident rate. The main research problem is whether these functions are similar, which enhances international transferability, or dissimilar, which reduces international transferability. Accident modification functions for horizontal curve radius developed in the countries listed above are synthesised. The sensitivity of the functions to other characteristics of curves than radius is examined. Accident modification functions developed in different countries have important similarities. The functions diverge with respect to accident rate in the sharpest curves.

  16. Horizontal high-pressure air injection well construction and operation

    Energy Technology Data Exchange (ETDEWEB)

    Hume, J. [Continental Resources Inc., ND (United States)

    2005-07-01

    This paper discussed the design and operational challenges of a horizontal high-pressure air injection well currently in use at the Cedar Hill Red River B field in North Dakota. The field was developed in 1994, using horizontal wells oriented from the northeast to the southwest corners of each section on 640 acre spacing. In March of 2001, the field was unitized resulting in a horizontal waterflood project and a 320 acre horizontal high pressure air injection project. Extreme temperatures and pressures occurring in the reservoir from the combustion processes associated with high pressure air injection have resulted in several challenges. Reservoir and fluid properties of the field were presented, as well as a type log. Details of the Buffalo and Cedar Hills field were also provided, with a comparison of horizontal and vertical patterns. A light oil displacement process was reviewed, with details of tubing leak corrosion, packer seal and detonation failures. Burn front exposure to casing was discussed, and a wellbore diagram was provided. Various horizontal conversions were discussed. A description of the Cedar Hills Compressor Station and compression trains was provided. It was concluded that knowledge gained from 25 years of vertical high pressure air injection experience has been successfully incorporated to create a safe and durable design. 1 tab., 16 figs.

  17. Should sex-ratio distorting parasites abandon horizontal transmission?

    Directory of Open Access Journals (Sweden)

    Ironside Joseph E

    2011-12-01

    Full Text Available Abstract Background Sex-ratio distorting parasites are of interest due to their effects upon host population dynamics and their potential to influence the evolution of host sex determination systems. In theory, the ability to distort host sex-ratios allows a parasite with efficient vertical (hereditary transmission to dispense completely with horizontal (infectious transmission. However, recent empirical studies indicate that some sex-ratio distorting parasites have retained the capability for horizontal transmission. Results Numerical simulations using biologically realistic parameters suggest that a feminising parasite is only likely to lose the capability for horizontal transmission if its host occurs at low density and/or has a male-biased primary sex ratio. It is also demonstrated that even a small amount of horizontal transmission can allow multiple feminising parasites to coexist within a single host population. Finally it is shown that, by boosting its host's rate of population growth, a feminising parasite can increase its own horizontal transmission and allow the invasion of other, more virulent parasites. Conclusions The prediction that sex-ratio distorting parasites are likely to retain a degree of horizontal transmission has important implications for the epidemiology and host-parasite interactions of these organisms. It may also explain the frequent co-occurrence of several sex-ratio distorting parasite species in nature.

  18. Distributed multiple path routing in complex networks

    Science.gov (United States)

    Chen, Guang; Wang, San-Xiu; Wu, Ling-Wei; Mei, Pan; Yang, Xu-Hua; Wen, Guang-Hui

    2016-12-01

    Routing in complex transmission networks is an important problem that has garnered extensive research interest in the recent years. In this paper, we propose a novel routing strategy called the distributed multiple path (DMP) routing strategy. For each of the O-D node pairs in a given network, the DMP routing strategy computes and stores multiple short-length paths that overlap less with each other in advance. And during the transmission stage, it rapidly selects an actual routing path which provides low transmission cost from the pre-computed paths for each transmission task, according to the real-time network transmission status information. Computer simulation results obtained for the lattice, ER random, and scale-free networks indicate that the strategy can significantly improve the anti-congestion ability of transmission networks, as well as provide favorable routing robustness against partial network failures.

  19. Local-time representation of path integrals.

    Science.gov (United States)

    Jizba, Petr; Zatloukal, Václav

    2015-12-01

    We derive a local-time path-integral representation for a generic one-dimensional time-independent system. In particular, we show how to rephrase the matrix elements of the Bloch density matrix as a path integral over x-dependent local-time profiles. The latter quantify the time that the sample paths x(t) in the Feynman path integral spend in the vicinity of an arbitrary point x. Generalization of the local-time representation that includes arbitrary functionals of the local time is also provided. We argue that the results obtained represent a powerful alternative to the traditional Feynman-Kac formula, particularly in the high- and low-temperature regimes. To illustrate this point, we apply our local-time representation to analyze the asymptotic behavior of the Bloch density matrix at low temperatures. Further salient issues, such as connections with the Sturm-Liouville theory and the Rayleigh-Ritz variational principle, are also discussed.

  20. Riemann Curvature Tensor and Closed Geodesic Paths

    Science.gov (United States)

    Morganstern, Ralph E.

    1977-01-01

    Demonstrates erroneous results obtained if change in a vector under parallel transport about a closed path in Riemannian spacetime is made in a complete circuit rather than just half a circuit. (Author/SL)

  1. Non-classical paths in interference experiments

    CERN Document Server

    Sawant, Rahul; Sinha, Aninda; Sinha, Supurna; Sinha, Urbasi

    2014-01-01

    In a double slit interference experiment, the wave function at the screen with both slits open is not exactly equal to the sum of the wave functions with the slits individually open one at a time. The three scenarios represent three different boundary conditions and as such, the superposition principle should not be applicable. However, most well known text books in quantum mechanics implicitly and/or explicitly use this assumption which is only approximately true. In our present study, we have used the Feynman path integral formalism to quantify contributions from non-classical paths in quantum interference experiments which provide a measurable deviation from a naive application of the superposition principle. A direct experimental demonstration for the existence of these non-classical paths is hard. We find that contributions from such paths can be significant and we propose simple three-slit interference experiments to directly confirm their existence.

  2. Nonclassical Paths in Quantum Interference Experiments

    Science.gov (United States)

    Sawant, Rahul; Samuel, Joseph; Sinha, Aninda; Sinha, Supurna; Sinha, Urbasi

    2014-09-01

    In a double slit interference experiment, the wave function at the screen with both slits open is not exactly equal to the sum of the wave functions with the slits individually open one at a time. The three scenarios represent three different boundary conditions and as such, the superposition principle should not be applicable. However, most well-known text books in quantum mechanics implicitly and/or explicitly use this assumption that is only approximately true. In our present study, we have used the Feynman path integral formalism to quantify contributions from nonclassical paths in quantum interference experiments that provide a measurable deviation from a naive application of the superposition principle. A direct experimental demonstration for the existence of these nonclassical paths is difficult to present. We find that contributions from such paths can be significant and we propose simple three-slit interference experiments to directly confirm their existence.

  3. Path Integral Approach to Atomic Collisions

    Science.gov (United States)

    Harris, Allison

    2016-09-01

    The Path Integral technique is an alternative formulation of quantum mechanics that is based on a Lagrangian approach. In its exact form, it is completely equivalent to the Hamiltonian-based Schrödinger equation approach. Developed by Feynman in the 1940's, following inspiration from Dirac, the path integral approach has been widely used in high energy physics, quantum field theory, and statistical mechanics. However, only in limited cases has the path integral approach been applied to quantum mechanical few-body scattering. We present a theoretical and computational development of the path integral method for use in the study of atomic collisions. Preliminary results are presented for some simple systems. Ultimately, this approach will be applied to few-body ion-atom collisions. Work supported by NSF grant PHY-1505217.

  4. Predicting missing links via significant paths

    CERN Document Server

    Zhu, Xuzhen; Cai, Shimin; Huang, Junming; Zhou, Tao

    2014-01-01

    Link prediction plays an important role in understanding intrinsic evolving mechanisms of networks. With the belief that the likelihood of the existence of a link between two nodes is strongly related with their similarity, many methods have been proposed to calculate node similarity based on node attributes and/or topological structures. Among a large variety of methods that take into account paths connecting the target pair of nodes, most of which neglect the heterogeneity of those paths. Our hypothesis is that a path consisting of small-degree nodes provides a strong evidence of similarity between two ends, accordingly, we propose a so-called sig- nificant path index in this Letter to leverage intermediate nodes' degrees in similarity calculation. Empirical experiments on twelve disparate real networks demonstrate that the proposed index outperforms the mainstream link prediction baselines.

  5. Aircraft Path Planning under Adverse Weather Conditions

    Directory of Open Access Journals (Sweden)

    Xie Z.

    2016-01-01

    Full Text Available In recent years, flight safety is still one of the main issues for all airlines. En route civil airplanes may encounter adverse weather conditions. Some fatal airplane accidents happened because of the weather disturbance. Moreover, we should also design path to avoid the prohibited area. Therefore a good path planning algorithm plays an increasingly important role in air traffic management. An efficient path planning algorithm can help the plane to avoid severe weather conditions, restricted areas and moving obstacles to ensure the safety of the cabin crews and passengers. Here, we build our algorithm based on the A* search algorithm. Moreover, our algorithm can also find the path with least energy costs. As a result, our algorithm can improve the safety operation of the airplanes and reduce the workload of pilots and air traffic controllers.

  6. Path integration in relativistic quantum mechanics

    CERN Document Server

    Redmount, I H; Redmount, Ian H.; Suen, Wai-Mo

    1993-01-01

    The simple physics of a free particle reveals important features of the path-integral formulation of relativistic quantum theories. The exact quantum-mechanical propagator is calculated here for a particle described by the simple relativistic action proportional to its proper time. This propagator is nonvanishing outside the light cone, implying that spacelike trajectories must be included in the path integral. The propagator matches the WKB approximation to the corresponding configuration-space path integral far from the light cone; outside the light cone that approximation consists of the contribution from a single spacelike geodesic. This propagator also has the unusual property that its short-time limit does not coincide with the WKB approximation, making the construction of a concrete skeletonized version of the path integral more complicated than in nonrelativistic theory.

  7. Path dependence and independent utility regulation

    DEFF Research Database (Denmark)

    Ibsen, Christian Lyhne; Skovgaard Poulsen, Lauge

    2007-01-01

    The establishment of the Danish independent regulatory authorities for the energy and telecommunications sectors was based upon EU directives as part of their liberalisation process. Following the concepts of transaction costs and path dependency this article analyses differences in independence...

  8. Northern Pintail - Flight Path Telemetry [ds117

    Data.gov (United States)

    California Department of Resources — North-south flight paths of radio-tagged female northern pintails were monitored in a section of Highway 152 near Los Banos, California during 4 and 11 November and...

  9. Path integral distance for data interpretation

    CERN Document Server

    Volchenkov, D

    2015-01-01

    The process of data interpretation is always based on the implicit introduction of equivalence relations on the set of walks over the database. Every equivalence relation on the set of walks specifies a Markov chain describing the transitions of a discrete time random walk. In order to geometrize and interpret the data, we propose the new distance between data units defined as a "Feynman path integral", in which all possible paths between any two nodes in a graph model of the data are taken into account, although some paths are more preferable than others. Such a path integral distance approach to the analysis of databases has proven its efficiency and success, especially on multivariate strongly correlated data where other methods fail to detect structural components (urban planning, historical language phylogenies, music, street fashion traits analysis, etc. ). We believe that it would become an invaluable tool for the intelligent complexity reduction and big data interpretation.

  10. Modeling DNA Dynamics by Path Integrals

    CERN Document Server

    Zoli, Marco

    2013-01-01

    Complementary strands in DNA double helix show temporary fluctuational openings which are essential to biological functions such as transcription and replication of the genetic information. Such large amplitude fluctuations, known as the breathing of DNA, are generally localized and, microscopically, are due to the breaking of the hydrogen bonds linking the base pairs (\\emph{bps}). I apply imaginary time path integral techniques to a mesoscopic Hamiltonian which accounts for the helicoidal geometry of a short circular DNA molecule. The \\emph{bps} displacements with respect to the ground state are interpreted as time dependent paths whose amplitudes are consistent with the model potential for the hydrogen bonds. The portion of the paths configuration space contributing to the partition function is determined by selecting the ensemble of paths which fulfill the second law of thermodynamics. Computations of the thermodynamics in the denaturation range show the energetic advantage for the equilibrium helicoidal g...

  11. Noncommutative integrability, paths and quasi-determinants

    CERN Document Server

    Di Francesco, Philippe

    2010-01-01

    In previous work, we showed that the solution of certain systems of discrete integrable equations, notably $Q$ and $T$-systems, is given in terms of partition functions of positively weighted paths, thereby proving the positive Laurent phenomenon of Fomin and Zelevinsky for these cases. This method of solution is amenable to generalization to non-commutative weighted paths. Under certain circumstances, these describe solutions of discrete evolution equations in non-commutative variables: Examples are the corresponding quantum cluster algebras [BZ], the Kontsevich evolution [DFK09b] and the $T$-systems themselves [DFK09a]. In this paper, we formulate certain non-commutative integrable evolutions by considering paths with non-commutative weights, together with an evolution of the weights that reduces to cluster algebra mutations in the commutative limit. The general weights are expressed as Laurent monomials of quasi-determinants of path partition functions, allowing for a non-commutative version of the positiv...

  12. Building a path in cell biology.

    Science.gov (United States)

    Voeltz, Gia; Cheeseman, Iain

    2012-11-01

    Setting up a new lab is an exciting but challenging prospect. We discuss our experiences in finding a path to tackle some of the key current questions in cell biology and the hurdles that we have encountered along the way.

  13. A chemist building paths to cell biology.

    Science.gov (United States)

    Weibel, Douglas B

    2013-11-01

    Galileo is reported to have stated, "Measure what is measurable and make measurable what is not so." My group's trajectory in cell biology has closely followed this philosophy, although it took some searching to find this path.

  14. Feasible Path Planning for Autonomous Vehicles

    Directory of Open Access Journals (Sweden)

    Vu Trieu Minh

    2014-01-01

    Full Text Available The objective of this paper is to find feasible path planning algorithms for nonholonomic vehicles including flatness, polynomial, and symmetric polynomial trajectories subject to the real vehicle dynamical constraints. Performances of these path planning methods are simulated and compared to evaluate the more realistic and smoother generated trajectories. Results show that the symmetric polynomial algorithm provides the smoothest trajectory. Therefore, this algorithm is recommended for the development of an automatic control for autonomous vehicles.

  15. Competition for shortest paths on sparse graphs.

    Science.gov (United States)

    Yeung, Chi Ho; Saad, David

    2012-05-18

    Optimal paths connecting randomly selected network nodes and fixed routers are studied analytically in the presence of a nonlinear overlap cost that penalizes congestion. Routing becomes more difficult as the number of selected nodes increases and exhibits ergodicity breaking in the case of multiple routers. The ground state of such systems reveals nonmonotonic complex behaviors in average path length and algorithmic convergence, depending on the network topology, and densities of communicating nodes and routers. A distributed linearly scalable routing algorithm is also devised.

  16. Dressed coordinates: The path-integral approach

    Science.gov (United States)

    Casana, R.; Flores-Hidalgo, G.; Pimentel, B. M.

    2007-02-01

    The recently introduced dressed coordinates are studied in the path-integral approach. These coordinates are defined in the context of a harmonic oscillator linearly coupled to massless scalar field and it is shown that in this model the dressed coordinates appear as a coordinate transformation preserving the path-integral functional measure. The analysis also generalizes the sum rules established in a previous work.

  17. Create three distinct career paths for innovators.

    Science.gov (United States)

    O'Connor, Gina Colarelli; Corbett, Andrew; Pierantozzi, Ron

    2009-12-01

    Large companies say they Create Three Distinct want to be Career Paths for Innovators innovative, but they fundamentally mismanage their talent. Expecting innovators to grow along with their projects-from discovery to incubation to acceleration--sets them up to fail. Most people excel at one of the phases, not all three. By allowing innovation employees to develop career paths suited to their strengths, companies will create a sustainable innovation function.

  18. The Feynman Path Goes Monte Carlo

    OpenAIRE

    Sauer, Tilman

    2001-01-01

    Path integral Monte Carlo (PIMC) simulations have become an important tool for the investigation of the statistical mechanics of quantum systems. I discuss some of the history of applying the Monte Carlo method to non-relativistic quantum systems in path-integral representation. The principle feasibility of the method was well established by the early eighties, a number of algorithmic improvements have been introduced in the last two decades.

  19. A novel method for robot path planning

    Institute of Scientific and Technical Information of China (English)

    CAI Qiang; LI Hai-sheng; YANG Qin; LI Ji-gang

    2009-01-01

    Path planning is one of the most important problems in the design of a mobile robot. A novel approach called generalized Voronoi diagrams (GVD) may deal with this matter. First, a method was introduced to normalize the obstacles and present efficient techniques for generating GVDs. Then a best path searching algorithm was presented. Examples implemented were given to indicate the availability of the mentioned algorithms. The approaches in this paper can also be used in applications including visualization, spatial data manipulation, etc.

  20. A Path Algorithm for Constrained Estimation.

    Science.gov (United States)

    Zhou, Hua; Lange, Kenneth

    2013-01-01

    Many least-square problems involve affine equality and inequality constraints. Although there are a variety of methods for solving such problems, most statisticians find constrained estimation challenging. The current article proposes a new path-following algorithm for quadratic programming that replaces hard constraints by what are called exact penalties. Similar penalties arise in l1 regularization in model selection. In the regularization setting, penalties encapsulate prior knowledge, and penalized parameter estimates represent a trade-off between the observed data and the prior knowledge. Classical penalty methods of optimization, such as the quadratic penalty method, solve a sequence of unconstrained problems that put greater and greater stress on meeting the constraints. In the limit as the penalty constant tends to ∞, one recovers the constrained solution. In the exact penalty method, squared penalties!are replaced by absolute value penalties, and the solution is recovered for a finite value of the penalty constant. The exact path-following method starts at the unconstrained solution and follows the solution path as the penalty constant increases. In the process, the solution path hits, slides along, and exits from the various constraints. Path following in Lasso penalized regression, in contrast, starts with a large value of the penalty constant and works its way downward. In both settings, inspection of the entire solution path is revealing. Just as with the Lasso and generalized Lasso, it is possible to plot the effective degrees of freedom along the solution path. For a strictly convex quadratic program, the exact penalty algorithm can be framed entirely in terms of the sweep operator of regression analysis. A few well-chosen examples illustrate the mechanics and potential of path following. This article has supplementary materials available online.

  1. Decomposing Path : The Nanosyntax of Directional Expressions

    OpenAIRE

    Pantcheva, Marina Blagoeva

    2011-01-01

    In my thesis, I investigate directional expressions cross-linguistically. I examine the morpho-syntactic structure of expressions of Goal (to the house), Source (from the house), Route (through the house), non-transitional paths (towards the house) and, finally, delimited paths (up to the house). I conclude that all these types of directional expressions are of different syntactic complexity. Precisely, Source expressions (from) are formed on the basis of Goal expressions (to) and Route expr...

  2. Dynamic Shortest Path Monitoring in Spatial Networks

    Institute of Scientific and Technical Information of China (English)

    Shuo Shang; Lisi Chen; Zhe-Wei Wei; Dan-Huai Guo; Ji-Rong Wen

    2016-01-01

    With the increasing availability of real-time traffic information, dynamic spatial networks are pervasive nowa-days and path planning in dynamic spatial networks becomes an important issue. In this light, we propose and investigate a novel problem of dynamically monitoring shortest paths in spatial networks (DSPM query). When a traveler aims to a des-tination, his/her shortest path to the destination may change due to two reasons: 1) the travel costs of some edges have been updated and 2) the traveler deviates from the pre-planned path. Our target is to accelerate the shortest path computing in dynamic spatial networks, and we believe that this study may be useful in many mobile applications, such as route planning and recommendation, car navigation and tracking, and location-based services in general. This problem is challenging due to two reasons: 1) how to maintain and reuse the existing computation results to accelerate the following computations, and 2) how to prune the search space effectively. To overcome these challenges, filter-and-refinement paradigm is adopted. We maintain an expansion tree and define a pair of upper and lower bounds to prune the search space. A series of optimization techniques are developed to accelerate the shortest path computing. The performance of the developed methods is studied in extensive experiments based on real spatial data.

  3. *-Regular Leavitt Path Algebras of Arbitrary Graphs

    Institute of Scientific and Technical Information of China (English)

    Gonzalo ARANDA PINO; Kulumani RANGASWAMY; Lia VA(S)

    2012-01-01

    If K is a field with involution and E an arbitrary graph,the involution from K naturally induces an involution of the Leavitt path algebra LK(E).We show that the involution on LK(E) is proper if the involution on K is positive-definite,even in the case when the graph E is not necessarily finite or row-finite.It has been shown that the Leavitt path algebra LK(E) is regular if and only if E is acyclic.We give necessary and sufficient conditions for LK(E) to be *-regular (i.e.,regular with proper involution).This characterization of *-regularity of a Leavitt path algebra is given in terms of an algebraic property of K,not just a graph-theoretic property of E.This differs from the.known characterizations of various other algebraic properties of a Leavitt path algebra in terms of graphtheoretic properties of E alone.As a corollary,we show that Handelman's conjecture (stating that every *-regular ring is unit-regular) holds for Leavitt path algebras.Moreover,its generalized version for rings with local units also continues to hold for Leavitt path algebras over arbitrary graphs.

  4. Lightning path simulation based on the stepped leader: Electrical conductivity effects

    Science.gov (United States)

    Mendes, Odim; Domingues, Margarete Oliveira

    2005-09-01

    A numerical simulation for the stepped leader path in the earth atmosphere has been developed to study the influence of the tropospheric electric conductivity on the lightning behaviour. This model is based on the assumption that the leader path follows the gradient of the electric potential. In the model, the charge configuration (amount of charge and location), the variation of the atmospheric conductivity, the charge deposited along the leader channel and the charge at the leader tip are considered. A perfectly conducting ground surface and a curl-free electric field assumption are considered too. The result of the simulation is that the inclusion of an atmospheric conductivity of exponentially increasing value with height alters the percentage of positive cloud-to-ground flashes compared to that percentage obtained assuming a constant conductivity profile. A higher amount of positive flashes occur for high altitude (low latitude) clouds even in the case of little horizontal displacement between the positive and the negative dipole charges in the cloud, that is, with no significant wind shear in the horizontal wind. The simulation has shown that positive lightning, the most dangerous kind, can occur in clear air at great distances from the thundercloud, with safety risk implications.

  5. Should tsunami simulations include a nonzero initial horizontal velocity?

    Science.gov (United States)

    Lotto, Gabriel C.; Nava, Gabriel; Dunham, Eric M.

    2017-08-01

    Tsunami propagation in the open ocean is most commonly modeled by solving the shallow water wave equations. These equations require initial conditions on sea surface height and depth-averaged horizontal particle velocity or, equivalently, horizontal momentum. While most modelers assume that initial velocity is zero, Y.T. Song and collaborators have argued for nonzero initial velocity, claiming that horizontal displacement of a sloping seafloor imparts significant horizontal momentum to the ocean. They show examples in which this effect increases the resulting tsunami height by a factor of two or more relative to models in which initial velocity is zero. We test this claim with a "full-physics" integrated dynamic rupture and tsunami model that couples the elastic response of the Earth to the linearized acoustic-gravitational response of a compressible ocean with gravity; the model self-consistently accounts for seismic waves in the solid Earth, acoustic waves in the ocean, and tsunamis (with dispersion at short wavelengths). Full-physics simulations of subduction zone megathrust ruptures and tsunamis in geometries with a sloping seafloor confirm that substantial horizontal momentum is imparted to the ocean. However, almost all of that initial momentum is carried away by ocean acoustic waves, with negligible momentum imparted to the tsunami. We also compare tsunami propagation in each simulation to that predicted by an equivalent shallow water wave simulation with varying assumptions regarding initial velocity. We find that the initial horizontal velocity conditions proposed by Song and collaborators consistently overestimate the tsunami amplitude and predict an inconsistent wave profile. Finally, we determine tsunami initial conditions that are rigorously consistent with our full-physics simulations by isolating the tsunami waves from ocean acoustic and seismic waves at some final time, and backpropagating the tsunami waves to their initial state by solving the

  6. System Finds Horizontal Location of Center of Gravity

    Science.gov (United States)

    Johnston, Albert S.; Howard, Richard T.; Brewster, Linda L.

    2006-01-01

    An instrumentation system rapidly and repeatedly determines the horizontal location of the center of gravity of a laboratory vehicle that slides horizontally on three air bearings (see Figure 1). Typically, knowledge of the horizontal center-of-mass location of such a vehicle is needed in order to balance the vehicle properly for an experiment and/or to assess the dynamic behavior of the vehicle. The system includes a load cell above each air bearing, electronic circuits that generate digital readings of the weight on each load cell, and a computer equipped with software that processes the readings. The total weight and, hence, the mass of the vehicle are computed from the sum of the load-cell weight readings. Then the horizontal position of the center of gravity is calculated straightforwardly as the weighted sum of the known position vectors of the air bearings, the contribution of each bearing being proportional to the weight on that bearing. In the initial application for which this system was devised, the center- of-mass calculation is particularly simple because the air bearings are located at corners of an equilateral triangle. However, the system is not restricted to this simple geometry. The system acquires and processes weight readings at a rate of 800 Hz for each load cell. The total weight and the horizontal location of the center of gravity are updated at a rate of 800/3 approx. equals 267 Hz. In a typical application, a technician would use the center-of-mass output of this instrumentation system as a guide to the manual placement of small weights on the vehicle to shift the center of gravity to a desired horizontal position. Usually, the desired horizontal position is that of the geometric center. Alternatively, this instrumentation system could be used to provide position feedback for a control system that would cause weights to be shifted automatically (see Figure 2) in an effort to keep the center of gravity at the geometric center.

  7. Parallel path planning in unknown terrains

    Science.gov (United States)

    Prassler, Erwin A.; Milios, Evangelos E.

    1991-03-01

    We present a parallel processing approach to path planning in unknown terrains which combines map-based and sensor-based techniques into a real-time capable navigation system. The method is based on massively parallel computations in a grid of simple processing elements denoted as cells. In the course of a relaxation process a potential distribution is created in the grid which exhibits a monotonous slope from a start cell to the cell corresponding to the robot''s goal position. A shortest path is determined by means of a gradient descent criterion which settles on the steepest descent in the potential distribution. Like high-level path planning algorithms our approach is capable of planning shortest paths through an arbitrarily cluttered large-scale terrain on the basis of its current internal map. Sequentially implemented its complexity is in the order of efficient classical path planning algorithms. Unlike these algorithms however the method is also highly responsive to new obstacles encountered in the terrain. By continuing the planning process during the robot''s locomotion information about previously unknown obstacles immediately affects further path planning without a need to interrupt the ongoing planning process. New obstacles cause distortions of the potential distribution which let the robot find proper detours. By ensuring a monotonous slope in the overall distribution we avoid local minimum effects which may trap a robot in the proximity of an obstacle configuration before it has reached its goal. 1 Until the recent past research on path planning in the presence of obstacles can be assigned to two major categories: map-based high-level planning approaches and sensor-based low-level conLrol approaches. In work such as 12 path planning is treated as a high-level planning task. Assuming that an (accnrae) precompiled map of the terrain is available high-level path planners provide paths which guarantee a collision-free locomotion through an arbitrary

  8. Reliability Analysis of Random Vibration Transmission Path Systems

    Directory of Open Access Journals (Sweden)

    Wei Zhao

    2017-01-01

    Full Text Available The vibration transmission path systems are generally composed of the vibration source, the vibration transfer path, and the vibration receiving structure. The transfer path is the medium of the vibration transmission. Moreover, the randomness of transfer path influences the transfer reliability greatly. In this paper, based on the matrix calculus, the generalized second moment technique, and the stochastic finite element theory, the effective approach for the transfer reliability of vibration transfer path systems was provided. The transfer reliability of vibration transfer path system with uncertain path parameters including path mass and path stiffness was analyzed theoretically and computed numerically, and the correlated mathematical expressions were derived. Thus, it provides the theoretical foundation for the dynamic design of vibration systems in practical project, so that most random path parameters can be considered to solve the random problems for vibration transfer path systems, which can avoid the system resonance failure.

  9. Comparison of flux measurement by open-path and close-path eddy covariance systems

    Institute of Scientific and Technical Information of China (English)

    SONG; Xia; YU; Guirui; LIU; Yunfen; SUN; Xiaomin; REN; Chua

    2005-01-01

    For flux measurement, the eddy covariance technique supplies a possibility to directly measure the exchange between vegetation and atmosphere; and there are two kinds of eddy covariance systems, open-path and close-path systems. For the system error, it may result in difference of flux measurements by two systems. Therefore, it is necessary to compare the measured results from them. ChinaFLUX covers of eight sites applied the micrometeorological method, in which Changbai Mountains (CBS) and Qianyanzhou (QYZ) carried out open-path eddy covariance (OPEC) and close-path eddy covariance (CPEC) measurements synchronously.In this paper the data sets of CBS and QYZ were employed. The delay time of close-path analyzer to the open-path analyzer was calculated; the spectra and cospectra of time-series data of OPEC and CPEC were analyzed; the open-path flux measurement was used as a standard comparison, the close-path flux measurement results were evaluated. The results show that, at two sites the delay time of CO2 density for close-path analyzer was about 7.0-8.0 s, H2O density about 8.0-9.0 s; the spectrum from the open-path, close-path and 3D sonic anemometer was consistent with the expected -2/3 slope (log-log plot), and the cospectra showed the expected slope of -4/3 in the internal subrange; the CO2 flux measured by the close-path sensor was about 84% of that of open-path measurement at QYZ, about 80% at CBS, and the latent heat flux was balanced for two systems at QYZ, 86% at CBS. From the flux difference between open-path and close-path analyzers, it could be inferred that the attenuation of turbulent fluctuations in flow through tube of CPEC affected H2O flux more significantly than CO2 flux. The gap between two systems was bigger at CBS than at QYZ; the diurnal variation in CO2 flux of two measurement systems was very consistent.

  10. SHP: Smooth Hypocycloidal Paths with Collision-Free and Decoupled Multi-Robot Path Planning

    Directory of Open Access Journals (Sweden)

    Abhijeet Ravankar

    2016-06-01

    Full Text Available Generating smooth and continuous paths for robots with collision avoidance, which avoid sharp turns, is an important problem in the context of autonomous robot navigation. This paper presents novel smooth hypocycloidal paths (SHP for robot motion. It is integrated with collision-free and decoupled multi-robot path planning. An SHP diffuses (i.e., moves points along segments the points of sharp turns in the global path of the map into nodes, which are used to generate smooth hypocycloidal curves that maintain a safe clearance in relation to the obstacles. These nodes are also used as safe points of retreat to avoid collision with other robots. The novel contributions of this work are as follows: (1 The proposed work is the first use of hypocycloid geometry to produce smooth and continuous paths for robot motion. A mathematical analysis of SHP generation in various scenarios is discussed. (2 The proposed work is also the first to consider the case of smooth and collision-free path generation for a load carrying robot. (3 Traditionally, path smoothing and collision avoidance have been addressed as separate problems. This work proposes integrated and decoupled collision-free multi-robot path planning. ‵Node caching‵ is proposed to improve efficiency. A decoupled approach with local communication enables the paths of robots to be dynamically changed. (4 A novel ‵multi-robot map update‵ in case of dynamic obstacles in the map is proposed, such that robots update other robots about the positions of dynamic obstacles in the map. A timestamp feature ensures that all the robots have the most updated map. Comparison between SHP and other path smoothing techniques and experimental results in real environments confirm that SHP can generate smooth paths for robots and avoid collision with other robots through local communication.

  11. Vertical-horizontal illusion: one eye is better than two.

    Science.gov (United States)

    Prinzmetal, W; Gettleman, L

    1993-01-01

    The vertical-horizontal illusion is the tendency for observers to overestimate the length of a vertical line relative to a horizontal line that has the same length. One explanation of this illusion is that the visual field is elongated in the horizontal direction, and that the vertical-horizontal illusion is a kind of framing effect (Künnapas, 1957a, 1957b, 1957c). Since the monocular visual field is less asymmetric than the combined visual field, this theory predicts that the illusion should be reduced with monocular presentation. This prediction was tested in five experiments, in which the vertical-horizontal illusion was examined in a variety of situations--including observers seated upright versus reclined 90 degrees, monocular presentation with the dominant versus the nondominant eye, viewing in the dark versus in the light, and viewing with asymmetrical frames of reference. The illusion was reliably reduced with monocular presentation under conditions that affected the asymmetry of the phenomenal visual field.

  12. Oriented cluster perforating technology and its application in horizontal wells

    Directory of Open Access Journals (Sweden)

    Huabin Chen

    2016-11-01

    Full Text Available An oriented cluster perforating technology, which integrates both advantages of cluster and oriented perforating, will help solve a series of technical complexities in horizontal well drilling. For realizing its better application in oil and gas development, a series of technologies were developed including perforator self-weight eccentricity, matching of the electronic selective module codes with the surface program control, axial centralized contact signal transmission, and post-perforation intercluster sealing insulation. In this way, the following functions could be realized, such as cable-transmission horizontal well perforator self-weight orientation, dynamic signal transmission, reliable addressing & selective perforation and post-perforation intercluster sealing. The combined perforation and bridge plug or the multi-cluster perforation can be fulfilled in one trip of perforation string. As a result, the horizontal-well oriented cluster perforating technology based on cable conveying was developed. This technology was successfully applied in unconventional gas reservoir exploitation, such as shale gas and coalbed methane, with accurate orientation, reliable selective perforation and satisfactory inter-cluster sealing. The horizontal-well oriented cluster perforating technology benefits the orientation of horizontal well drilling with a definite target and direction, which provides a powerful support for the subsequent reservoir stimulation. It also promotes the fracturing fluid to sweep the principal pay zones to the maximum extent. Moreover, it is conductive to the formation of complex fracture networks in the reservoirs, making quality and efficient development of unconventional gas reservoirs possible.

  13. Challenges in reservoir engineering from prospects for horizontal wells

    Energy Technology Data Exchange (ETDEWEB)

    Fayers, F.J.; Arbabi, S.; Aziz, K. [Stanford Univ., CA (United States). Dept. of Petroleum Engineering

    1995-01-01

    In this review paper, a variety of reservoir applications are illustrated where horizontal wells can have advantages over the use of conventional vertical wells. It is stressed that one of the key advantages relates to the opportunities to optimize the orientation and position of horizontal wells with respect to the principal directions for the reservoir depositional environment, but this may interact with natural fracture or fault directions, and the principal stress direction if hydraulic fracturing is to be considered. Analytical methods for calculating critical coning rates in homogeneous reservoirs are reviewed, and shown to give a very large range of results for horizontal wells. The potential significance of two-phase pressure drop within the wellbore on GOR performance is discussed, and a range of uncertainty by a factor of six is indicated between the use of various correlations for calculating the well pressure drop. In the final section studies are summarized for a gas coning application using ECLIPSE, a commercial simulator. The simulation results indicated an apparently invariant behaviour on GOR history with respect to the effects of wellbore two-phase pressure drop when the horizontal well was produced at constant rate in a homogeneous reservoir. However, when the controlling conditions on the horizontal well were made more representative, and reservoir non-uniformity was introduced, it was then found that the two-phase pressure drop became very significant. Some areas for further research are indicated. (Author)

  14. Effects of vertical shear in modelling horizontal oceanic dispersion

    Science.gov (United States)

    Lanotte, A. S.; Corrado, R.; Palatella, L.; Pizzigalli, C.; Schipa, I.; Santoleri, R.

    2016-02-01

    The effect of vertical shear on the horizontal dispersion properties of passive tracer particles on the continental shelf of the South Mediterranean is investigated by means of observation and model data. In situ current measurements reveal that vertical gradients of horizontal velocities in the upper mixing layer decorrelate quite fast ( ˜ 1 day), whereas an eddy-permitting ocean model, such as the Mediterranean Forecasting System, tends to overestimate such decorrelation time because of finite resolution effects. Horizontal dispersion, simulated by the Mediterranean sea Forecasting System, is mostly affected by: (1) unresolved scale motions, and mesoscale motions that are largely smoothed out at scales close to the grid spacing; (2) poorly resolved time variability in the profiles of the horizontal velocities in the upper layer. For the case study we have analysed, we show that a suitable use of deterministic kinematic parametrizations is helpful to implement realistic statistical features of tracer dispersion in two and three dimensions. The approach here suggested provides a functional tool to control the horizontal spreading of small organisms or substance concentrations, and is thus relevant for marine biology, pollutant dispersion as well as oil spill applications.

  15. Investigation of gravity waves using horizontally resolved radial velocity measurements

    Directory of Open Access Journals (Sweden)

    G. Stober

    2013-06-01

    Full Text Available The Middle Atmosphere Alomar Radar System (MAARSY on the island Andøya in Northern Norway (69.3° N, 16.0° E observes polar mesospheric summer echoes (PMSE. These echoes are used as tracers of atmospheric dynamics to investigate the horizontal wind variability at high temporal and spatial resolution. MAARSY has the capability of a pulse-to-pulse beam steering allowing for systematic scanning experiments to study the horizontal structure of the backscatterers as well as to measure the radial velocities for each beam direction. Here we present a method to retrieve gravity wave parameters from these horizontally resolved radial wind variations by applying velocity azimuth display and volume velocity processing. Based on the observations a detailed comparison of the two wind analysis techniques is carried out in order to determine the zonal and meridional wind as well as to measure first order inhomogeneities. Further, we demonstrate the possibility to resolve the horizontal wave properties, e.g. horizontal wavelength, phase velocity and propagation direction. The robustness of the estimated gravity wave parameters is tested by a simple atmospheric model.

  16. The interconnection between biofilm formation and horizontal gene transfer.

    Science.gov (United States)

    Madsen, Jonas Stenløkke; Burmølle, Mette; Hansen, Lars Hestbjerg; Sørensen, Søren Johannes

    2012-07-01

    Recent research has revealed that horizontal gene transfer and biofilm formation are connected processes. Although published research investigating this interconnectedness is still limited, we will review this subject in order to highlight the potential of these observations because of their believed importance in the understanding of the adaptation and subsequent evolution of social traits in bacteria. Here, we discuss current evidence for such interconnectedness centred on plasmids. Horizontal transfer rates are typically higher in biofilm communities compared with those in planktonic states. Biofilms, furthermore, promote plasmid stability and may enhance the host range of mobile genetic elements that are transferred horizontally. Plasmids, on the other hand, are very well suited to promote the evolution of social traits such as biofilm formation. This, essentially, transpires because plasmids are independent replicons that enhance their own success by promoting inter-bacterial interactions. They typically also carry genes that heighten their hosts' direct fitness. Furthermore, current research shows that the so-called mafia traits encoded on mobile genetic elements can enforce bacteria to maintain stable social interactions. It also indicates that horizontal gene transfer ultimately enhances the relatedness of bacteria carrying the mobile genetic elements of the same origin. The perspective of this review extends to an overall interconnectedness between horizontal gene transfer, mobile genetic elements and social evolution of bacteria.

  17. Research on bulging plate of scaler for horizontal pendulum tiltmeter

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhi-zhong; ZHU Hu; WU Jian

    2005-01-01

    @@ After the horizontal pendulum is used in ground-tilt measurement, its scaling has drawn great attentions from the people, because without a correct calibration of scale value, the observation is of little application significance. From the 1920's, quite a few scholars were engaged in the researches in this respect. And this question was satisfactorily solved until 1962 when Verbaandert (1962) invented the bulging plate, i.e., mercury-cup scaler.After further improvement, the V-M quartz horizontal pendulum tiltmeter was used globally in observation and great success was achieved (Melchior, 1966, 1978). In China, the quartz horizontal pendulum tiltmeter as well as the bulging-plate scaler were developed at the beginning of 1970's and then put into use after some improvements (ZHU and FENG, 1980). The successful observation by SQ quartz horizontal pendulum tiltmeter should be related not only to the excellent performance of horizontal pendulum, but also to its accurate calibration. The bulging plate plays an important role in calibration, because it is the critical component of scaler.

  18. A heat transfer model of a horizontal ground heat exchanger

    Science.gov (United States)

    Mironov, R. E.; Shtern, Yu. I.; Shtern, M. Yu.; Rogachev, M. S.

    2016-04-01

    Ground-source heat pumps are gaining popularity in Eastern Europe, especially those which are using the horizontal ground heat exchanger (GHX). Due to the difficulty of accessing GHX after the installation, materials and the quality of the installation must satisfy the very high requirements. An inaccurate calculation of GHX can be the reason of a scarcity of heat power in a crucial moment. So far, there isn't any appropriate mathematical description of the horizontal GHX which takes into account the mutual influence of GHX pipes on each other. To solve this problem we used the temperature wave approach. As a result, a mathematical model which describes the dependence of the heat transfer rate per unit length of the horizontal GHX pipe on the thermal properties of soil, operating time of GHX and the distance between pipes was obtained. Using this model, heat transfer rates per unit length of a horizontal GHX were plotted as functions of the distance between pipes and operating time. The modeling shows that heat transfer rates decreases rapidly with the distance between pipes lower then 2 meters. After the launch of heat pump, heat power of GHX is reduced during the first 20 - 30 days and get steady after that. The obtained results correlate with experimental data. Therefore the proposed mathematical model can be used to design a horizontal GHX with the optimal characteristics, and predict its capability during operation.

  19. Investigation of gravity waves using horizontally resolved radial velocity measurements

    Science.gov (United States)

    Stober, G.; Sommer, S.; Rapp, M.; Latteck, R.

    2013-10-01

    The Middle Atmosphere Alomar Radar System (MAARSY) on the island of Andøya in Northern Norway (69.3° N, 16.0° E) observes polar mesospheric summer echoes (PMSE). These echoes are used as tracers of atmospheric dynamics to investigate the horizontal wind variability at high temporal and spatial resolution. MAARSY has the capability of pulse-to-pulse beam steering allowing for systematic scanning experiments to study the horizontal structure of the backscatterers as well as to measure the radial velocities for each beam direction. Here we present a method to retrieve gravity wave parameters from these horizontally resolved radial wind variations by applying velocity azimuth display and volume velocity processing. Based on the observations a detailed comparison of the two wind analysis techniques is carried out in order to determine the zonal and meridional wind as well as to measure first-order inhomogeneities. Further, we demonstrate the possibility to resolve the horizontal wave properties, e.g., horizontal wavelength, phase velocity and propagation direction. The robustness of the estimated gravity wave parameters is tested by a simple atmospheric model.

  20. Investigation of gravity waves using horizontally resolved radial velocity measurements

    Directory of Open Access Journals (Sweden)

    G. Stober

    2013-10-01

    Full Text Available The Middle Atmosphere Alomar Radar System (MAARSY on the island of Andøya in Northern Norway (69.3° N, 16.0° E observes polar mesospheric summer echoes (PMSE. These echoes are used as tracers of atmospheric dynamics to investigate the horizontal wind variability at high temporal and spatial resolution. MAARSY has the capability of pulse-to-pulse beam steering allowing for systematic scanning experiments to study the horizontal structure of the backscatterers as well as to measure the radial velocities for each beam direction. Here we present a method to retrieve gravity wave parameters from these horizontally resolved radial wind variations by applying velocity azimuth display and volume velocity processing. Based on the observations a detailed comparison of the two wind analysis techniques is carried out in order to determine the zonal and meridional wind as well as to measure first-order inhomogeneities. Further, we demonstrate the possibility to resolve the horizontal wave properties, e.g., horizontal wavelength, phase velocity and propagation direction. The robustness of the estimated gravity wave parameters is tested by a simple atmospheric model.

  1. Experimental evolution as an efficient tool to dissect adaptive paths to antibiotic resistance.

    Science.gov (United States)

    Jansen, Gunther; Barbosa, Camilo; Schulenburg, Hinrich

    2013-12-01

    Antibiotic treatments increasingly fail due to rapid dissemination of drug resistance. Comparative genomics of clinical isolates highlights the role of de novo adaptive mutations and horizontal gene transfer (HGT) in the acquisition of resistance. Yet it cannot fully describe the selective pressures and evolutionary trajectories that yielded today's problematic strains. Experimental evolution offers a compelling addition to such studies because the combination of replicated experiments under tightly controlled conditions with genomics of intermediate time points allows real-time reconstruction of evolutionary trajectories. Recent studies thus established causal links between antibiotic deployment therapies and the course and timing of mutations, the cost of resistance and the likelihood of compensating mutations. They particularly underscored the importance of long-term effects. Similar investigations incorporating horizontal gene transfer (HGT) are wanting, likely because of difficulties associated with its integration into experiments. In this review, we describe current advances in experimental evolution of antibiotic resistance and reflect on ways to incorporate horizontal gene transfer into the approach. We contend it provides a powerful tool for systematic and highly controlled dissection of evolutionary paths to antibiotic resistance that needs to be taken into account for the development of sustainable anti-bacterial treatment strategies.

  2. Path Integral Techniques in Conformal Field Theory

    CERN Document Server

    Van Tonder, A J

    2004-01-01

    We present the theory of a two-dimensional conformal scalar field using path integral techniques. We derive the conformal anomaly using an adaptation of the method of Fujikawa, and compare the result with a derivation based on a Pauli-Villars measure, where the anomaly is shifted from the path integral measure to the energy-momentum trace. In the path integral approach the energy-momentum is a true coordinate-invariant tensor quantity, and we explain how it is related to the corresponding non-tensor object arising in the operator approach, obtaining an intuitive explanation within the context of the path integral approach for the anomalous transformation law and anomalous Ward identities of the latter. After carefully calculating nontrivial contact terms arising in certain energy-momentum products, we use these to provide a simple consistency check confirming the change of variables formula for the path integral and to review the relationship between the conformal anomaly and the energy-momentum two-point fun...

  3. Accurate free energy calculation along optimized paths.

    Science.gov (United States)

    Chen, Changjun; Xiao, Yi

    2010-05-01

    The path-based methods of free energy calculation, such as thermodynamic integration and free energy perturbation, are simple in theory, but difficult in practice because in most cases smooth paths do not exist, especially for large molecules. In this article, we present a novel method to build the transition path of a peptide. We use harmonic potentials to restrain its nonhydrogen atom dihedrals in the initial state and set the equilibrium angles of the potentials as those in the final state. Through a series of steps of geometrical optimization, we can construct a smooth and short path from the initial state to the final state. This path can be used to calculate free energy difference. To validate this method, we apply it to a small 10-ALA peptide and find that the calculated free energy changes in helix-helix and helix-hairpin transitions are both self-convergent and cross-convergent. We also calculate the free energy differences between different stable states of beta-hairpin trpzip2, and the results show that this method is more efficient than the conventional molecular dynamics method in accurate free energy calculation.

  4. Default Path and Dedicated Path: A New Approach to Realize IP Directly Over WDM

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Combining IP and WDM is an attractive direction for research. Instead the point to point linking method, this paper proposes a new approach to realize IP directly over WDM, called DPDP (default path and dedicated path), presents a conceivable architecture in detail and explains its working procedure. A lot of problems related with this design are also discussed.

  5. 14 CFR 23.61 - Takeoff flight path.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Takeoff flight path. 23.61 Section 23.61... flight path. For each commuter category airplane, the takeoff flight path must be determined as follows: (a) The takeoff flight path begins 35 feet above the takeoff surface at the end of the...

  6. Path Analysis: A Link between Family Theory and Reseach.

    Science.gov (United States)

    Rank, Mark R.; Sabatelli, Ronald M.

    This paper discusses path analysis and the applicability of this methodology to the field of family studies. The statistical assumptions made in path analysis are presented along with a description of the two types of models within path analysis, i.e., recursive and non-recursive. Methods of calculating in the path model and the advantages of…

  7. Stealth-Based Path Planning using Corridor Maps

    NARCIS (Netherlands)

    Geraerts, R.J.|info:eu-repo/dai/nl/304830291; Schager, E.

    2010-01-01

    A relatively new area within the field of path planning deals with computing a stealthy path for a character moving in a virtual environment. Besides efficiently obtaining a path that is collision-free, short and smooth, the added difficulty is that the path must have little or no exposure to observ

  8. An Adaptive Path Planning Algorithm for Cooperating Unmanned Air Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Cunningham, C.T.; Roberts, R.S.

    2000-09-12

    An adaptive path planning algorithm is presented for cooperating Unmanned Air Vehicles (UAVs) that are used to deploy and operate land-based sensor networks. The algorithm employs a global cost function to generate paths for the UAVs, and adapts the paths to exceptions that might occur. Examples are provided of the paths and adaptation.

  9. Horizontal displacements contribution to tsunami wave energy balance

    CERN Document Server

    Dutykh, Denys; Chubarov, Leonid; Shokin, Yuriy

    2010-01-01

    The main reason for the generation of tsunamis is the deformation of the bottom of the ocean caused by an underwater earthquake. Usually, only the vertical bottom motion is taken into accound while the horizontal displacements are neglected. In the present paper we study both the vertical and the horizontal bottom motion while we propose a novel methodology for reconstructing the bottom coseismic displacements field which is transmitted to the free surface using a new three-dimensional Weakly Nonlinear (WN) approach. We pay a special attention to the evolution of kinetic and potential energies of the resulting wave while the contribution of horizontal displacements into wave energy balance is also quantified. Approaches proposed in this study are illustrated on the July 17, 2006 Java tsunami.

  10. The Interplay of Different Types of Governance in Horizontal Cooperations

    DEFF Research Database (Denmark)

    Raue, Jan Simon; Wieland, Andreas

    2015-01-01

    Purpose – Over the last decades, horizontal cooperations between logistics service providers (LSPs) have become a well-established organizational form and their use is expected to grow even further in the future. In spite of this increasing importance of horizontal LSP cooperations, little research...... has been done to reveal how to govern these relationships successfully. Particularly, the role of contractual governance and its interplay with operational governance mechanisms remain to be investigated. The paper aims to discuss these issues. Design/methodology/approach – This research analyzes......-based learning. At the same time, relational capital is always complemented by contractual safeguarding independently from the desired cooperation outcome. Originality/value – This is the first study analyzing the role of contractual safeguarding in horizontal cooperations between LSPs. It shows its interplay...

  11. Interpretation models and charts of production profiles in horizontal wells

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Stratified flow is common for the gravity segregation and flow regimes are very complex because of borehole inclination,therefore,all the conventional production logging tools cannot be effectively applied in horizontal wells,thus significantly increasing the difficulties in log interpretation. In this paper,firstly,the overseas progress in updated integration tools for horizontal wells and production profile interpretation methods has been discussed in brief. Secondly,by means of theory study and experimental simulations,we have obtained the production profile interpretation model and experimental interpretation charts,which have been calibrated by the improved downhole technology and optimization methods. Finally,we have interpreted X-well with the production profile interpretation software designed by us,and it proves that the methods are useful for the production profile interpretation in horizontal wells.

  12. HORIZONTAL LAPLACE OPERATOR IN REAL FINSLER VECTOR BUNDLES

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A vector bundle F over the tangent bundle TM of a manifold M is said to be a Finsler vector bundle if it is isomorphic to the pull-back π*E of a vector bundle E over M([1]). In this article the authors study the h-Laplace operator in Finsler vector bundles.An h-Laplace operator is defined, first for functions and then for horizontal Finsler forms on E. Using the h-Laplace operator, the authors define the h-harmonic function and h-harmonic horizontal Finsler vector fields, and furthermore prove some integral formulas for the h-Laplace operator, horizontal Finsler vector fields, and scalar fields on E.

  13. Simulations on the AGS horizontal tune jump mechanism

    Energy Technology Data Exchange (ETDEWEB)

    Lin,F.; Huang, H.; Luccio, A. U.; Roser, T.

    2009-05-04

    A new horizontal tune jump mechanism has been proposed to overcome the horizontal intrinsic resonances and preserve the polarization of the proton beam in the Alternating Gradient Synchrotron (AGS) during the energy ramp. An adiabatic change of the AGS lattice is needed to avoid the emittance growth in both horizontal and vertical planes, as the emittance growth can deteriorate the polarization of the proton beam. Two critical questions are necessary to be answered: how fast can the lattice be changed and how much emittance growth can be tolerated from both optics and polarization points of view? Preliminary simulations, using a realistic AGS lattice and acceleration rate, have been carried out to give a first glance of this mechanism. Results with different optics are presented in this paper.

  14. The Horizontal Branch of the Sculptor Dwarf galaxy

    CERN Document Server

    Salaris, Maurizio; Tolstoy, Eline; Fiorentino, Giuliana; Cassisi, Santi

    2013-01-01

    We have performed the first detailed simulation of the horizontal branch of the Sculptor dwarf spheroidal galaxy by means of synthetic modelling techniques,taking consistently into account the star formation history and metallicity evolution as determined from the main sequence and red giant branch spectroscopic observations. The only free parameter in the whole analysis is the integrated mass loss of red giant branch stars. This is the first time that synthetic horizontal branch models, consistent with the complex star formation history of a galaxy, are calculated and matched to the observations. We find that the metallicity range covered by the star formation history, as constrained by observations, plus a simple mass loss law, enable us to cover both the full magnitude and colour range of HB stars. In addition the number count distribution along the observed horizontal branch, can be also reproduced, provided that the red giant branch mass loss is mildly metallicity dependent, with a very small dispersion ...

  15. Horizontally root fractured teeth with pulpal vitality - two case reports

    Science.gov (United States)

    Silva, Luciano; Álvares, Pâmella; Arruda, José Alcides; Silva, Leni Verônica; Rodrigues, Cleomar; Sobral, Ana Paula Veras; Silveira, Marcia

    2016-01-01

    This case study reports the successful outcome of horizontal root fractures of two different patients, which took place in permanent incisors. Report 1 describes a case of a 29-year-old patient who suffered a mandibular trauma affecting mainly the lower central incisors, caused by a car accident. A panoramic radiograph was taken right after the accident and showed a horizontal root fracture in the middle third of tooth 42, which went untreated. Report 2 illustrates a case of a 17-year-old male patient who searched for orthodontic therapy and the periapical radiograph showed horizontal root fracture in tooth 11 caused by a previous trauma, which went untreated as well. There was healing through the reestablishment of pulp activity and dental coloration without professional intervention. PMID:28070245

  16. Predrilled liner / barefoot completions in horizontal sour gas wells

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, M.W. [Mobil Erdgas-Erdoel GmbH, Celle (Germany)

    1999-09-01

    When selecting the completion type of a horizontal well, all relevant production and reservoir engineering aspects have to be taken into consideration to ensure safe and optimised long-term production. Especially in the case of sour gas wells, which require corrosion-resistant and expensive alloys, the technical/economic need to run a liner in the horizontal section is often discussed. This paper compares the preinvestment for a 'predrilled liner' with the cost of downhole operations which may become necessary in a 'barefoot completion'. These calculated 'risked savings' - as a function of the horizontal length - lead to a break-even point which is intended to assist in the decision to run a liner in sour gas wells or not. (orig.)

  17. Exploration of Horizontal Intrinsic Spin Resonances in the AGS

    Science.gov (United States)

    Lin, Fanglei; Lee, S. Y.; Ahrens, Leif A.; Bai, Mei; Brown, Kevin; Courant, Ernest D.; Glenn, Joseph W.; Huang, Haixin; Luccio, Alfredo; Mackay, William W.; Ptitsyn, Vadim; Roser, Thomas; Tepikian, Steven; Tsoupas, Nicholaos; Wood, Jeff; Yip, Yin; Okamura, Masahiro; Takano, Junpei

    2006-04-01

    Siberian snakes have been employed to overcome spin resonances during polarized proton acceleration. Considering limited space in the AGS, strong partial snakes that rotate the spin by less than 180 degrees can be used to avoid the spin imperfection and intrinsic resonances in low energy accelerators. However, the tilt of spin away from the vertical direction may become sensitive to horizontal betatron motion which can also cause spin depolarization. These resonances, called horizontal intrinsic spin resonances, have been observed in simulations. Preliminary measurements with beam were also carried out in AGS 2005 polarized proton run. During the AGS 2006 run, we plan to explore the details about the horizontal intrinsics resonances further. This paper describes the experimental methods and the latest results.

  18. [Horizontal root fracture repaired by cementum--a case report].

    Science.gov (United States)

    Lin, K R; Kuo, J S

    1989-09-20

    Horizontal root fractures are rare among dental trauma. According to Dr. Andreasen's report there are four types of repairs after root fractures. They are 1. healing with calcified tissue; 2. interposition of connective tissue; 3. interposition of connective and bony tissue; 4. interposition of granulation tissue. This report presented a case of horizontal root fracture in a 27 years old female patient. The patient had a trauma in the front teeth about 15 years ago. Spontaneous healing occurred without dental treatment at that moment. However, symptoms appeared recently as a dento-alveolar abscess. Radiograph revealed a horizontal fracture at the middle third of the root portion of the left upper central incisor, and irregular hard tissue over the fractured area. Histologically, the main component of repair tissue is cementum.

  19. FLOW DISTRIBUTION IN A SOLAR COLLECTOR PANEL WITH HORIZONTAL FINS

    DEFF Research Database (Denmark)

    Fan, Jianhua; Shah, Louise Jivan; Furbo, Simon

    2005-01-01

    The objective of this work is to theoretically and experimentally investigate the flow and temperature distribution in a solar collector panel with an absorber consisting of horizontal fins. Fluid flow and heat transfer in the collector panel are studied by means of computational fluid dynamics...... (CFD) calculations. Further, experimental investigations of a 12.5 m² solar collector panel with 16 parallel connected horizontal fins are carried out. The flow distribution through the absorber is evaluated by means of temperature measurements on the backside of the absorber tubes. The measured......, temperature of inlet flow and collector tilt angle are shown. Based on the investigations preliminary recommendations for the operation of the investigated collector are given. For instance, minimum flow rate in order to avoid boiling in the horizontal strips is recommended....

  20. A hybrid model of a subminiature helicopter in horizontal turn

    Institute of Scientific and Technical Information of China (English)

    Chen Li; Gong Zhenbang; Liu Liang

    2007-01-01

    A hybrid model of a subminiature helicopter in horizontal turn is presented. This model is based on a mechanism model and its compensated neural network (NN). First, the nonlinear dynamics of a subminiature helicopter is established. Through the linearization of the nonlinear dynamics on a trim point, the linear time-invariant mechanism model in horizontal turn is obtained. Then a diagonal recursive neural network is used to compensate the model error between the mechanism model and the nonlinear model, thus the hybrid model of a subminiature helicopter in horizontal turn is achieved. Simulation results show that the hybrid model has higher accuracy than the mechanism model and the obtained compensated-NN has good generalization capability.

  1. Ballistics Model for Particles on a Horizontal Plane in a Vacuum Propelled by a Vertically Impinging Gas Jet

    Science.gov (United States)

    Lane, J. E.; Metzger, P. T.

    2010-01-01

    A simple trajectory model has been developed and is presented. The particle trajectory path is estimated by computing the vertical position as a function of the horizontal position using a constant horizontal velocity and a vertical acceleration approximated as a power law. The vertical particle position is then found by solving the differential equation of motion using a double integral of vertical acceleration divided by the square of the horizontal velocity, integrated over the horizontal position. The input parameters are: x(sub 0) and y(sub 0), the initial particle starting point; the derivative of the trajectory at x(sub 0) and y(sub 0), s(sub 0) = s(x(sub 0))= dx(y)/dy conditional expectation y = y((sub 0); and b where bx(sub 0)/y(sub 0) is the final trajectory angle before gravity pulls the particle down. The final parameter v(sub 0) is an approximation to a constant horizontal velocity. This model is time independent, providing vertical position x as a function of horizontal distance y: x(y) = (x(sub 0) + s(sub 0) (y-y(sub 0))) + bx(sub 0) -(s(sub 0)y(sub 0) ((y - y(sub 0)/y(sub 0) - ln((y/y(sub 0)))-((g(y-y(sub 0)(exp 2))/ 2((v(sub 0)(exp 2). The first term on the right in the above equation is due to simple ballistics and a spherically expanding gas so that the trajectory is a straight line intersecting (0,0), which is the point at the center of the gas impingement on the surface. The second term on the right is due to vertical acceleration, which may be positive or negative. The last term on the right is the gravity term, which for a particle with velocities less than escape velocity will eventually bring the particle back to the ground. The parameters b, s(sub 0), and in some cases v(sub 0), are taken from an interpolation of similar parameters determined from a CFD simulation matrix, coupled with complete particle trajectory simulations.

  2. Self-calibrating common-path interferometry.

    Science.gov (United States)

    Porras-Aguilar, Rosario; Falaggis, Konstantinos; Ramirez-San-Juan, Julio C; Ramos-Garcia, Ruben

    2015-02-09

    A quantitative phase measuring technique is presented that estimates the object phase from a series of phase shifted interferograms that are obtained in a common-path configuration with unknown phase shifts. The derived random phase shifting algorithm for common-path interferometers is based on the Generalized Phase Contrast theory [pl. Opt.40(2), 268 (2001)10.1063/1.1404846], which accounts for the particular image formation and includes effects that are not present in two-beam interferometry. It is shown experimentally that this technique can be used within common-path configurations employing nonlinear liquid crystal materials as self-induced phase filters for quantitative phase imaging without the need of phase shift calibrations. The advantages of such liquid crystal elements compared to spatial light modulator based solutions are given by the cost-effectiveness, self-alignment, and the generation of diminutive dimensions of the phase filter size, giving unique performance advantages.

  3. The path exchange method for hybrid LCA.

    Science.gov (United States)

    Lenzen, Manfred; Crawford, Robert

    2009-11-01

    Hybrid techniques for Life-Cycle Assessment (LCA) provide a way of combining the accuracy of process analysis and the completeness of input-output analysis. A number of methods have been suggested to implement a hybrid LCA in practice, with the main challenge being the integration of specific process data with an overarching input-output system. In this work we present a new hybrid LCA method which works at the finest input-output level of detail: structural paths. This new Path Exchange method avoids double-counting and system disturbance just as previous hybrid LCA methods, but instead of a large LCA database it requires only a minimum of external information on those structural paths that are to be represented by process data.

  4. Approximate shortest homotopic paths in weighted regions

    KAUST Repository

    Cheng, Siuwing

    2012-02-01

    A path P between two points s and t in a polygonal subdivision T with obstacles and weighted regions defines a class of paths that can be deformed to P without passing over any obstacle. We present the first algorithm that, given P and a relative error tolerance ε (0, 1), computes a path from this class with cost at most 1 + ε times the optimum. The running time is O(h 3/ε 2kn polylog (k,n,1/ε)), where k is the number of segments in P and h and n are the numbers of obstacles and vertices in T, respectively. The constant in the running time of our algorithm depends on some geometric parameters and the ratio of the maximum region weight to the minimum region weight. © 2012 World Scientific Publishing Company.

  5. Approximate Shortest Homotopic Paths in Weighted Regions

    KAUST Repository

    Cheng, Siu-Wing

    2010-01-01

    Let P be a path between two points s and t in a polygonal subdivision T with obstacles and weighted regions. Given a relative error tolerance ε ∈(0,1), we present the first algorithm to compute a path between s and t that can be deformed to P without passing over any obstacle and the path cost is within a factor 1 + ε of the optimum. The running time is O(h 3/ε2 kn polylog(k, n, 1/ε)), where k is the number of segments in P and h and n are the numbers of obstacles and vertices in T, respectively. The constant in the running time of our algorithm depends on some geometric parameters and the ratio of the maximum region weight to the minimum region weight. © 2010 Springer-Verlag.

  6. Quickest Paths for Different Network Router Mechanisms

    Energy Technology Data Exchange (ETDEWEB)

    Rao, N.S.V.; Grimmell, W.C.; Radhakrishnan, S.; Bang, Y.C.

    2000-06-01

    The quickest path problem deals with the transmission of a message of size {sigma} from a source to a destination with the minimum end-to-end delay over a network with bandwidth and delay constraints on the links. The authors consider four basic modes and two variations for the message delivery at the nodes reflecting the mechanisms such as circuit switching, Internet protocol, and their combinations. For each of the first three modes, they present O(m{sup 2} + mn log n) time algorithm to compute the quickest path for a given message size {sigma}. For the last mode, the quickest path can be computed in O(m + n log n) time.

  7. Quickest Paths in Simulations of Pedestrians

    CERN Document Server

    Kretz, Tobias; Hengst, Stefan; Kautzsch, Lukas; Pohlmann, Andrej; Vortisch, Peter

    2011-01-01

    This contribution proposes a method to make agents in a microscopic simulation of pedestrian traffic walk approximately along a path of estimated minimal remaining travel time to their destination. Usually models of pedestrian dynamics are (implicitly) built on the assumption that pedestrians walk along the shortest path. Model elements formulated to make pedestrians locally avoid collisions and intrusion into personal space do not produce motion on quickest paths. Therefore a special model element is needed, if one wants to model and simulate pedestrians for whom travel time matters most (e.g. travelers in a station hall who are late for a train). Here such a model element is proposed, discussed and used within the Social Force Model.

  8. Shortest Path Computation with No Information Leakage

    CERN Document Server

    Mouratidis, Kyriakos

    2012-01-01

    Shortest path computation is one of the most common queries in location-based services (LBSs). Although particularly useful, such queries raise serious privacy concerns. Exposing to a (potentially untrusted) LBS the client's position and her destination may reveal personal information, such as social habits, health condition, shopping preferences, lifestyle choices, etc. The only existing method for privacy-preserving shortest path computation follows the obfuscation paradigm; it prevents the LBS from inferring the source and destination of the query with a probability higher than a threshold. This implies, however, that the LBS still deduces some information (albeit not exact) about the client's location and her destination. In this paper we aim at strong privacy, where the adversary learns nothing about the shortest path query. We achieve this via established private information retrieval techniques, which we treat as black-box building blocks. Experiments on real, large-scale road networks assess the pract...

  9. Maxillary repositioning according to Frankfort horizontal plane during orthognathic surgery

    Directory of Open Access Journals (Sweden)

    Mehdi Ghoreishian

    2013-01-01

    Full Text Available Context: There are a lot of disagreements among surgeons over controlling the maxillary position during orthognathic surgery. Aim: To investigate maxillary repositioning according to Frankfort horizontal plane in orthognathic surgery. Materials and Methods: Fourteen patients were selected who were submitted to maxillary or bimaxillary surgery. Maxillary model surgery was performed based on the treatment planning and an intermediate splint was made. The surgical technique in this study was based on maxillary osteotomy according to the findings of the model surgery, in a manner that the osteotomy line was parallel to the Frankfort horizontal plane. Intermediate splint was used for repositioning of the maxilla in the new position and the vertical position of that was determined according to external reference point and fixed on this position. The upper central incisor designed from prediction tracing and post-operative cephalometry on the first tracing. The new position of maxilla was evaluated horizontally and vertically. Statistical Analysis Used: A paired t-test was used to compare the predicted maxillary position and the actual position. Association between these two groups of variables was evaluated with Pearson correlation. Results: The mean difference between the maxillary planned position and post-operative cephalometric radiography varied between 0.3 mm and 0.9 mm vertically (P value = 0.315 and 0.0 mm and 0.9 mm horizontally (P value = 0.034. The averages of horizontally and vertically observed changes were 0.3 mm and 0.17 mm respectively (P < 0.001. Conclusion: Good surgical accuracy in repositioning of the maxilla can be achieved according to Frankfort horizontal plane during the surgery. By eliminating the ramping effect the accuracy of surgery increases.

  10. Association between axial length and horizontal and vertical globe diameters.

    Science.gov (United States)

    Jonas, Jost B; Ohno-Matsui, Kyoko; Holbach, Leonard; Panda-Jonas, Songhomitra

    2017-02-01

    To assess relationships between axial length and the horizontal and vertical globe diameters. The study consisted of enucleated human eyes. The horizontal, vertical, and sagittal diameters were measured. The study included 135 globes removed because of malignant uveal melanoma (111 globes) or end-stage painful glaucoma (n = 24 eyes). Mean axial, horizontal, and vertical diameters were 24.6 ± 2.6 mm (range: 20-35 mm), 23.7 ± 1.4 mm (range: 21-29 mm) and 23.7 ± 1.4 mm (range: 20-29 mm) respectively. The horizontal diameter and vertical diameter did not differ significantly (P = 0.92), while both were significantly (P globe diameter (P globe diameter = 0.84 × horizontal globe diameter + 3.69). The axial diameter was significantly (P 24 mm, the horizontal and vertical globe diameter increased by a lower amount of 0.19 and 0.21 mm, respectively, for each mm increase in axial diameter. Myopic enlargement of the globe beyond an axial length of 24 mm takes place predominantly in the sagittal axis, leading to a change in the globe form from a sphere to an elongated form. It fits with the notion that myopic elongation may occur by an elongation of the eye walls in regions close to the globe's equator.

  11. OPTIMIZATION OF TIMES AND COSTS OF PROJECT OF HORIZONTAL LAMINATOR PRODUCTION USING PERT/CPM TECHNICAL

    Directory of Open Access Journals (Sweden)

    Fernando Henrique Lermen

    2016-09-01

    Full Text Available The PERT/CPM is a technique widely used in both the scheduling and in the project feasibility in terms of cost control and time.  In order to optimize time and costs involved in production, the work presented here aims to apply the PERT/CPM technique in the production project of the Horizontal Laminator, a machine used to cut polyurethane foam blocks in the mattresses industries. For the application of PERT/CPM technique in the project of Horizontal Laminator production were identified the activities that compose the project, the dependence between them, the normal and accelerated durations and the normal and accelerated costs. In this study, deterministic estimates for the duration of the activities were considered. The results show that the project can be completed in 520 hours at a total cost of R$7,042.50, when all activities are performed in their normal durations.  When all the activities that compose the critical path are accelerated, the project can be completed in 333.3 hours at a total cost of R$9,263.01. If the activities slacks have been exploited, it can obtain a final total cost of R$6,157.8, without changing the new duration of the project. It is noteworthy that the final total cost of the project if the slacks are used, will be lower than the initial cost. Regarding the initial cost of the project, after the application of the PERT/CPM technique, it presents a decrease of 12.56% of the total project cost.

  12. Accounting for the effect of horizontal gradients in limb measurements of scattered sunlight

    Directory of Open Access Journals (Sweden)

    J. Puķīte

    2007-11-01

    Full Text Available Limb measurements provided by the SCanning Imaging Absorption spectrometer for Atmospheric CHartographY (SCIAMACHY on the ENVISAT satellite allow retrieving stratospheric profiles of various trace gases on a global scale, among them BrO for the first time. For limb observations in the UV/VIS spectral region the instrument measures scattered light with a complex distribution of light paths: the light is measured at different elevation angles and can be scattered or absorbed in the atmosphere or reflected by the ground. By means of spectroscopy and radiative transfer modelling the measurements can be inverted to retrieve the vertical distribution of stratospheric trace gases.

    A full spherical 3-D Monte Carlo radiative transfer model "Tracy-II" is applied in this study. The Monte Carlo method benefits from conceptual simplicity and allows realizing the concept of full spherical geometry of the atmosphere and also its 3-D properties, which is important for a realistic description of the limb geometry. Furthermore it allows accounting for horizontal gradients in the distribution of trace gases.

    In this study the effect ofhorizontal inhomogeneous distributions of trace gases on the retrieval of profiles from limb measurements of scattered UV/VIS light is investigated. We introduce a method to correct for this effect by combining consecutive limb scanning sequences and utilizing the overlap in their measurement sensitivity regions. It is found that if horizontal inhomogenity is not properly accounted for, typical errors of 20% for NO2 and up to 50% for OClO around the altitude of the profile peak can arise for measurements close to the Arctic polar vortex boundary in boreal winter.

  13. Extensive intra-kingdom horizontal gene transfer converging on a fungal fructose transporter gene.

    Directory of Open Access Journals (Sweden)

    Marco A Coelho

    2013-06-01

    Full Text Available Comparative genomics revealed in the last decade a scenario of rampant horizontal gene transfer (HGT among prokaryotes, but for fungi a clearly dominant pattern of vertical inheritance still stands, punctuated however by an increasing number of exceptions. In the present work, we studied the phylogenetic distribution and pattern of inheritance of a fungal gene encoding a fructose transporter (FSY1 with unique substrate selectivity. 109 FSY1 homologues were identified in two sub-phyla of the Ascomycota, in a survey that included 241 available fungal genomes. At least 10 independent inter-species instances of horizontal gene transfer (HGT involving FSY1 were identified, supported by strong phylogenetic evidence and synteny analyses. The acquisition of FSY1 through HGT was sometimes suggestive of xenolog gene displacement, but several cases of pseudoparalogy were also uncovered. Moreover, evidence was found for successive HGT events, possibly including those responsible for transmission of the gene among yeast lineages. These occurrences do not seem to be driven by functional diversification of the Fsy1 proteins because Fsy1 homologues from widely distant lineages, including at least one acquired by HGT, appear to have similar biochemical properties. In summary, retracing the evolutionary path of the FSY1 gene brought to light an unparalleled number of independent HGT events involving a single fungal gene. We propose that the turbulent evolutionary history of the gene may be linked to the unique biochemical properties of the encoded transporter, whose predictable effect on fitness may be highly variable. In general, our results support the most recent views suggesting that inter-species HGT may have contributed much more substantially to shape fungal genomes than heretofore assumed.

  14. Tornado intensity estimated from damage path dimensions.

    Science.gov (United States)

    Elsner, James B; Jagger, Thomas H; Elsner, Ian J

    2014-01-01

    The Newcastle/Moore and El Reno tornadoes of May 2013 are recent reminders of the destructive power of tornadoes. A direct estimate of a tornado's power is difficult and dangerous to get. An indirect estimate on a categorical scale is available from a post-storm survery of the damage. Wind speed bounds are attached to the scale, but the scale is not adequate for analyzing trends in tornado intensity separate from trends in tornado frequency. Here tornado intensity on a continuum is estimated from damage path length and width, which are measured on continuous scales and correlated to the EF rating. The wind speeds on the EF scale are treated as interval censored data and regressed onto the path dimensions and fatalities. The regression model indicates a 25% increase in expected intensity over a threshold intensity of 29 m s(-1) for a 100 km increase in path length and a 17% increase in expected intensity for a one km increase in path width. The model shows a 43% increase in the expected intensity when fatalities are observed controlling for path dimensions. The estimated wind speeds correlate at a level of .77 (.34, .93) [95% confidence interval] with a small sample of wind speeds estimated independently from a doppler radar calibration. The estimated wind speeds allow analyses to be done on the tornado database that are not possible with the categorical scale. The modeled intensities can be used in climatology and in environmental and engineering applications. Research is needed to understand the upward trends in path length and width.

  15. Robust paths to realize nonadiabatic holonomic gates

    Science.gov (United States)

    Xu, G. F.; Zhao, P. Z.; Tong, D. M.; Sjöqvist, Erik

    2017-05-01

    To realize one desired nonadiabatic holonomic gate, various equivalent evolution paths can be chosen. However, in the presence of errors, these paths become inequivalent. In this paper we investigate the difference of these evolution paths in the presence of systematic Rabi-frequency errors and aim to find paths with optimal robustness to realize one-qubit nonadiabatic holonomic gates. We focus on three types of evolution paths in the Λ system: paths belonging to the original two-loop scheme [E. Sjöqvist et al., New J. Phys. 14, 103035 (2012), 10.1088/1367-2630/14/10/103035], the single-loop multiple-pulse scheme [E. Herterich and E. Sjöqvist, Phys. Rev. A 94, 052310 (2016), 10.1103/PhysRevA.94.052310], and the off-resonance single-shot scheme [G. F. Xu et al., Phys. Rev. Lett. 92, 052302 (2015), 10.1103/PhysRevLett.92.052302; E. Sjöqvist, Phys. Lett. A 380, 65 (2016), 10.1016/j.physleta.2015.10.006]. Whereas both the single-loop multiple-pulse and single-shot schemes aim to improve the robustness of the original two-loop scheme by shortening the exposure to decoherence, we find here that the two-loop scheme is more robust to systematic errors in the Rabi frequencies. More importantly, we derive conditions under which the resilience to this kind of error can be optimized, thereby strengthening the robustness of nonadiabatic holonomic gates.

  16. Quantum cosmology based on discrete Feynman paths

    Energy Technology Data Exchange (ETDEWEB)

    Chew, Geoffrey F.

    2002-10-10

    Although the rules for interpreting local quantum theory imply discretization of process, Lorentz covariance is usually regarded as precluding time quantization. Nevertheless a time-discretized quantum representation of redshifting spatially-homogeneous universe may be based on discrete-step Feynman paths carrying causal Lorentz-invariant action--paths that not only propagate the wave function but provide a phenomenologically-promising elementary-particle Hilbert-space basis. In a model under development, local path steps are at Planck scale while, at a much larger ''wave-function scale'', global steps separate successive wave-functions. Wave-function spacetime is but a tiny fraction of path spacetime. Electromagnetic and gravitational actions are ''at a distance'' in Wheeler-Feynman sense while strong (color) and weak (isospin) actions, as well as action of particle motion, are ''local'' in a sense paralleling the action of local field theory. ''Nonmaterial'' path segments and ''trivial events'' collaborate to define energy and gravity. Photons coupled to conserved electric charge enjoy privileged model status among elementary fermions and vector bosons. Although real path parameters provide no immediate meaning for ''measurement'', the phase of the complex wave function allows significance for ''information'' accumulated through ''gentle'' electromagnetic events involving charged matter and ''soft'' photons. Through its soft-photon content the wave function is an ''information reservoir''.

  17. A model of strategic marketing alliances for hospices: horizontal alliances.

    Science.gov (United States)

    Self, D R; Starnes, B J

    1999-01-01

    This article develops two previous research efforts. William J. Winston (1994, 1995) has proposed a set of strategies by which health care organizations can benefit from forging strategic alliances. Raadt and Self (1997) have proposed a classification model of alliances including horizontal, vertical, internal and osmotic. In the first of two articles, this paper presents a model of horizontal alliances. The subsets include transregional, service mergers, networks, venture capital investments, trade and professional organizations, and promotional alliances. Advantages and disadvantages of each are discussed.

  18. FLOW DISTRIBUTION IN A SOLAR COLLECTOR PANEL WITH HORIZONTAL FINS

    DEFF Research Database (Denmark)

    Fan, Jianhua; Shah, Louise Jivan; Furbo, Simon

    2005-01-01

    (CFD) calculations. Further, experimental investigations of a 12.5 m² solar collector panel with 16 parallel connected horizontal fins are carried out. The flow distribution through the absorber is evaluated by means of temperature measurements on the backside of the absorber tubes. The measured......The objective of this work is to theoretically and experimentally investigate the flow and temperature distribution in a solar collector panel with an absorber consisting of horizontal fins. Fluid flow and heat transfer in the collector panel are studied by means of computational fluid dynamics...

  19. The 'horizontal direct effect' of EU international agreements

    DEFF Research Database (Denmark)

    Gáspár-Szilágyi, Szilárd

    2015-01-01

    This article looks at a less discussed topic in European legal scholarship: the horizontal direct effect of EU international agreements and the Court of Justice’s apparent reluctance to expressly confirm it. It is argued that the direct effect of EU international agreements has been confirmed...... in proceedings involving private individuals/professionals against the private regulatory bodies of a profession or a State owned and controlled entity. However, direct effect has not yet been expressly confirmed in cases involving veritable horizontal relationships, between private parties of equal positions...

  20. Horizontal Stratification in Access to Danish University Programmes

    DEFF Research Database (Denmark)

    Munk, Martin D.; Thomsen, Jens Peter

    2017-01-01

    In this paper, we use register data to examine horizontal stratification within university institutions and university fields of study in Denmark, a country that has experienced a reduction of the social class gap in access to higher education. First, we argue that it is important to use a relati...... in different fields of study and university institutions. Most importantly, we find distinct patterns of horizontal stratification by field of study and parental occupation that would have remained hidden had we used more aggregated classifications for field of study and social origin....

  1. Experimental study of buoyancy driven natural ventilation through horizontal openings

    DEFF Research Database (Denmark)

    Heiselberg, Per; Li, Zhigang

    2007-01-01

    An experimental study of buoyancy driven natural ventilation through single-sided horizontal openings was performed in a full-scale laboratory test rig. Measurements were made for opening ratios L/D range from 0.027 to 4.455, where L and D are the length and the diameter of the opening, respectiv......An experimental study of buoyancy driven natural ventilation through single-sided horizontal openings was performed in a full-scale laboratory test rig. Measurements were made for opening ratios L/D range from 0.027 to 4.455, where L and D are the length and the diameter of the opening...

  2. Horizontal symmetry in the algebraic approach of genetic code

    CERN Document Server

    Godina-Nava, J J

    2013-01-01

    Using concepts of physics of elementary particles concerning the breaking of symmetry and grannd unified theory we propose to study with the algebraic approximation the degeneracy finded in the genetic code with the incorporation of a horizontal symmetry used in gauge theories to fit the contents of the multiplets of the genetic code. It is used the algebraic approch of Hornos et. al. \\cite{main,PRL71,PRE,MPLB}. We propose an example for the incorporation of horizontal symmetry to study mixtures of elements of the multiplets.

  3. Horizontal symmetry in the algebraic approach of genetic code

    OpenAIRE

    Godina-Nava, J. J.

    2013-01-01

    Using concepts of physics of elementary particles concerning the breaking of symmetry and grannd unified theory we propose to study with the algebraic approximation the degeneracy finded in the genetic code with the incorporation of a horizontal symmetry used in gauge theories to fit the contents of the multiplets of the genetic code. It is used the algebraic approch of Hornos et. al. \\cite{main,PRL71,PRE,MPLB}. We propose an example for the incorporation of horizontal symmetry to study mixtu...

  4. Explicit Dynamic FEM Analysis of Multipass Vertical-Horizontal Rolling

    Institute of Scientific and Technical Information of China (English)

    YU Hai-liang; LIU Xiang-hua; ZHAO Xian-ming; WU Di; Y.Kusaba

    2006-01-01

    Three passes of plate rolling during vertical-horizontal rolling process are simulated with explicit dynamic finite element method and updating geometric method. The equivalent strain and stress fields, and shape change at the head and tail of slab during rolling are obtained. The calculated result of the shape at the head and tail of slab is in good agreement with the measured one. The explicit dynamic finite element method and updating geometric method can be used effectively to analyze the multipass vertical-horizontal (V-H) rolling process.

  5. Horizontal canal benign paroxysmal positional vertigo in a fighter pilot

    OpenAIRE

    Su-Jiang Xie; Jiang-Chang Wang; Li Ding; Xi-Qing Sun

    2011-01-01

    Benign paroxysmal positional vertigo (BPPV) is the most common disorder of the peripheral vestibular system, characterized by intense, positional provoked vertigo. BPPV is thought to occur due to canalithiasis of the posterior semicircular canal. Recently, a new entity of BPPV, known as horizontal canal (HC)-BPPV, has been recognized. Although only 3 to 8% of BPPV is due to horizontal canal involvement, HC-BPPV is not rare. We present a case of a naval fighter pilot who had an incident of HC-...

  6. Horizontal canal benign paroxysmal positional vertigo in a fighter pilot

    Directory of Open Access Journals (Sweden)

    Su-Jiang Xie

    2011-01-01

    Full Text Available Benign paroxysmal positional vertigo (BPPV is the most common disorder of the peripheral vestibular system, characterized by intense, positional provoked vertigo. BPPV is thought to occur due to canalithiasis of the posterior semicircular canal. Recently, a new entity of BPPV, known as horizontal canal (HC-BPPV, has been recognized. Although only 3 to 8% of BPPV is due to horizontal canal involvement, HC-BPPV is not rare. We present a case of a naval fighter pilot who had an incident of HC-BPPV on the ground. The pilot aeromedical evaluation and considerations are discussed.

  7. Horizontal canal benign paroxysmal positional vertigo in a fighter pilot.

    Science.gov (United States)

    Xie, Su-Jiang; Wang, Jiang-Chang; Ding, Li; Sun, Xi-Qing

    2011-01-01

    Benign paroxysmal positional vertigo (BPPV) is the most common disorder of the peripheral vestibular system, characterized by intense, positional provoked vertigo. BPPV is thought to occur due to canalithiasis of the posterior semicircular canal. Recently, a new entity of BPPV, known as horizontal canal (HC)-BPPV, has been recognized. Although only 3 to 8% of BPPV is due to horizontal canal involvement, HC-BPPV is not rare. We present a case of a naval fighter pilot who had an incident of HC-BPPV on the ground. The pilot aeromedical evaluation and considerations are discussed.

  8. Development of methodology for horizontal axis wind turbine dynamic analysis

    Science.gov (United States)

    Dugundji, J.

    1982-01-01

    Horizontal axis wind turbine dynamics were studied. The following findings are summarized: (1) review of the MOSTAS computer programs for dynamic analysis of horizontal axis wind turbines; (2) review of various analysis methods for rotating systems with periodic coefficients; (3) review of structural dynamics analysis tools for large wind turbine; (4) experiments for yaw characteristics of a rotating rotor; (5) development of a finite element model for rotors; (6) development of simple models for aeroelastics; and (7) development of simple models for stability and response of wind turbines on flexible towers.

  9. Unified analysis of pressure melting of ice around horizontal columns

    Institute of Scientific and Technical Information of China (English)

    LIU Feng; CHEN Wenzhen; MENG Bin; GONG Miao

    2007-01-01

    The contact melting processes of ice, caused by pressure under the two-dimension axisymmetric horizontal columns, are generally studied. The unified mathematical expressions of the characteristic parameters for the pressure contact melting processes are obtained. Applying these expressions to the analysis of the pressure contact melting of ice around the horizontal cylinder, elliptical cylinder and flat plate, the related results in the published literatures are obtained, which prove the correctness and validity of the expressions. In addition, the expressions for the pressure contact melting of ice around the wedge-shaped object are also derived.

  10. Adaptive cancellation of Es layer interference using auxiliary horizontal antennas

    Institute of Scientific and Technical Information of China (English)

    Zhao Long; Zhang Ning

    2006-01-01

    Based on a dual-polarization high-frequency wave radar system, an adaptive system using horizontal antennas for the suppression of the Es layer interference (ELI) is described. The data received from the horizontal antennas were correlated with the data received from the Vertically Polarized Antennas (VPAs) to estimate and cancel the interference adaptively in the VPAs. Suppressing the interference after each coherent integration time interval, about 25 dB signal-to-interference ratio is expected with the experimentally derived data.

  11. NONLINEAR DYNAMICAL CHARACTERISTICS OF PILES UNDER HORIZONTAL VIBRATION

    Institute of Scientific and Technical Information of China (English)

    HU Yu-jia; CHENG Chang-jun; YANG Xiao

    2005-01-01

    The pile-soil system is regarded as a visco-elastic half-space embedded pile. Based on the method of continuum mechanics, a nonlinear mathematical model of pilesoil interaction was established-a coupling nonlinear boundary value problem. Under the case of horizontal vibration, the nonlinearly dynamical characteristics of pile applying the axis force were studied in horizontal direction in frequency domain. The effects of parameters, especially the axis force on the stiffness were studied in detail. The numerical results suggest that it is possible that the pile applying an axis force will lose its stability. So, the effect of the axis force on the pile is considered.

  12. Path planning for everday robotics with SANDROS

    Energy Technology Data Exchange (ETDEWEB)

    Watterberg, P.; Xavier, P. [Sandia National Labs., Albuquerque, NM (United States); Hwang, Y. [Korea Inst. of Science and Technology, Seoul (Korea, Republic of)

    1997-02-01

    We discuss the integration of the SANDROS path planner into a general robot simulation and control package with the inclusion of a fast geometry engine for distance calculations. This creates a single system that allows the path to be computed, simulated, and then executed on the physical robot. The architecture and usage procedures are presented. Also, we present examples of its usage in typical environments found in our organization. The resulting system is as easy to use as the general simulation system (which is in common use here) and is fast enough (example problems are solved in seconds) to be used interactively on an everyday basis.

  13. Airway Tree Extraction with Locally Optimal Paths

    DEFF Research Database (Denmark)

    Lo, Pechin Chien Pau; Sporring, Jon; Pedersen, Jesper Johannes Holst

    2009-01-01

    This paper proposes a method to extract the airway tree from CT images by continually extending the tree with locally optimal paths. This is in contrast to commonly used region growing based approaches that only search the space of the immediate neighbors. The result is a much more robust method...... for tree extraction that can overcome local occlusions. The cost function for obtaining the optimal paths takes into account of an airway probability map as well as measures of airway shape and orientation derived from multi-scale Hessian eigen analysis on the airway probability. Significant improvements...

  14. Field theory a path integral approach

    CERN Document Server

    Das, Ashok

    2006-01-01

    This unique book describes quantum field theory completely within the context of path integrals. With its utility in a variety of fields in physics, the subject matter is primarily developed within the context of quantum mechanics before going into specialized areas.Adding new material keenly requested by readers, this second edition is an important expansion of the popular first edition. Two extra chapters cover path integral quantization of gauge theories and anomalies, and a new section extends the supersymmetry chapter, where singular potentials in supersymmetric systems are described.

  15. Determinants of Box Products of Paths

    CERN Document Server

    Pragel, Daniel

    2011-01-01

    Suppose that G is the graph obtained by taking the box product of a path of length n and a path of length m. Let M be the adjacency matrix of G. If n=m, H.M. Rara showed in 1996 that det(M)=0. We extend this result to allow n and m to be any positive integers, and show that, if gcd(n+1,m+1)>1, then det(M)=0; otherwise, if gcd(n+1,m+1)=1, then det(M)=(-1)^(nm/2).

  16. Vessel tree extraction using locally optimal paths

    DEFF Research Database (Denmark)

    Lo, Pechin Chien Pau; van Ginneken, Bram; de Bruijne, Marleen

    2010-01-01

    This paper proposes a method to extract vessel trees by continually extending detected branches with locally optimal paths. Our approach uses a cost function from a multi scale vessel enhancement filter. Optimal paths are selected based on rules that take into account the geometric characteristics...... of the vessel tree. Experiments were performed on 10 low dose chest CT scans for which the pulmonary vessel trees were extracted. The proposed method is shown to extract a better connected vessel tree and extract more of the small peripheral vessels in comparison to applying a threshold on the output...

  17. Stability Analysis of Path-vector Routing

    CERN Document Server

    Dimitri, Papadimitriou

    2012-01-01

    Most studies on path-vector routing stability have been conducted empirically by means of ad-hoc analysis of BGP data traces. None of them consider prior specification of an analytic method including the use of stability measurement metrics for the systematic analysis of BGP traces and associated meta-processing for determining the local state of the routing system. In this paper, we define a set of metrics that characterize the local stability properties of path-vector routing such as BGP (Border Gateway Protocol). By means of these stability metrics, we propose a method to analyze the effects of BGP policy- and protocol-induced instability on local routers.

  18. Analysis of Path-vector Routing Stability

    CERN Document Server

    Dimitri, Papadimitriou

    2012-01-01

    Most studies on path-vector routing stability have been conducted empirically by means of ad-hoc analysis of BGP data traces. None of them consider prior specification of an analytic method including the use of stability measurement metrics for the systematic analysis of BGP traces and associated meta-processing for determining the local state of the routing system. In this paper, we define a set of metrics that characterize the local stability properties of path-vector routing such as BGP (Border Gateway Protocol). By means of these stability metrics, we propose a method to analyze the effects of BGP policy- and protocol-induced instability on local routers.

  19. Gas Path Sealing in Turbine Engines

    Science.gov (United States)

    Ludwig, L. P.

    1978-01-01

    A survey of gas path seals is presented with particular attention given to sealing clearance effects on engine component efficiency. The effects on compressor pressure ratio and stall margin are pointed out. Various case-rotor relative displacements, which affect gas path seal clearances, are identified. Forces produced by nonuniform sealing clearances and their effect on rotor stability are discussed qualitatively, and recent work on turbine-blade-tip sealing for high temperature is described. The need for active clearance control and for engine structural analysis is discussed. The functions of the internal-flow system and its seals are reviewed.

  20. Flight Path Recovery System (FPRS) design study

    Energy Technology Data Exchange (ETDEWEB)

    1978-09-01

    The study contained herein presents a design for a Flight Path Recovery System (FPPS) for use in the NURE Program which will be more accurate than systems presently used, provide position location data in digital form suitable for automatic data processing, and provide for flight path recovery in a more economic and operationally suitable manner. The design is based upon the use of presently available hardware and technoloy, and presents little, it any, development risk. In addition, a Flight Test Plan designed to test the FPRS design concept is presented.

  1. Enduring Paths, Crossroads and Intersections: Path-breaking Knowledges in Pede Hollist's So the Path Does Not Die

    Directory of Open Access Journals (Sweden)

    Samuel Alpha Kamara

    2015-09-01

    Full Text Available Among other things, So the Path Does Not Die rekindles age-old themes such as tradition versus change; ethnicity, racism, sexism, and marginal identities; individual and institutional corruption; Diaspora and home; love and sacrifice; civil war and rehabilitation with fresh insights and focus. This article examines these themes in the novel's treatment of Talaba culture and its Musudugu myth.

  2. Survey of Robot 3D Path Planning Algorithms

    OpenAIRE

    Liang Yang; Juntong Qi; Dalei Song; Jizhong Xiao; Jianda Han; Yong Xia

    2016-01-01

    Robot 3D (three-dimension) path planning targets for finding an optimal and collision-free path in a 3D workspace while taking into account kinematic constraints (including geometric, physical, and temporal constraints). The purpose of path planning, unlike motion planning which must be taken into consideration of dynamics, is to find a kinematically optimal path with the least time as well as model the environment completely. We discuss the fundamentals of these most successful robot 3D path...

  3. Success of Path Dependence Through Perpetuation of Failure During Reform

    OpenAIRE

    E Kasabov

    2010-01-01

    The primary purpose of this paper is to extend current debates about path dependence and to contribute to scholarship by addressing inadequately researched aspects of path dependence: the role of individuals in sustaining long-standing 'inefficient' institutions; the balance of 'path following' and 'path violation'; and path dependent resource utilisation, not resource allocation. These matters are illustrated through and discussed in the context of 'asset-stripping' and 'rent-seeking' in the...

  4. Evolution of the horizontal drilling operations in the Ramos field; Evolucion de la perforacion horizontal en el Yacimiento Ramos

    Energy Technology Data Exchange (ETDEWEB)

    Piasco, Luis E.; Alegria, Antonio; Eguia, Hugo V.; Luna, Juan C. [PLUSPETROL Exploracion y Produccion, Buenos Aires (Argentina); Marcelo, Nguyen [PLUSPETROL Peru Corporation, Lima (Peru)

    1999-07-01

    The purpose of this paper is to show the progress related to the horizontal drilling operations in the Ramos Field in accordance with the technology evolution and the reservoir knowledge. The Ramos field, characterized as a natural fractured reservoir of quartzitic sandstones, has been subject for the application of the horizontal drilling techniques with the objective of maximize the production and to avoid water conning problems in the future. This paper describes chronologically, the experiences and the technology that helped to achieve the different proposed objectives and to reach improvements on the horizontal an Malt drilling operations. On this way, we finish successfully the drilling and completion operations in the Ramos 1010 multilateral well. This well has two cased branches and is the first well in his type in the whole subandean belt. (author)

  5. Dynamic Surface and Active Disturbance Rejection Control for Path Following of an Underactuated UUV

    Directory of Open Access Journals (Sweden)

    Juan Li

    2014-01-01

    Full Text Available This paper addresses the problem of accurate path following control for an underactuated unmanned underwater vehicle (UUV in the horizontal plane. For an underactuated UUV, the line-of-sight (LOS guidance method is adopted to map 2D reference trajectory into a desired orientation, and through the tracking of heading to achieve path following, where the sideslip is introduced to modify the desired orientation. In this paper, we propose a method called dynamic surface and active disturbance rejection control (DS-ADRC to solve the path following control problem. This controller can effectively avoid the phenomenon of explosion of terms in the conventional backstepping method, reduce the dependence on the UUV controller mathematical model, and enhance the antijamming ability. Simulation is carried out to verify the effectiveness of the proposed control method for an underactuated UUV. The results show that, even for this controller with disturbance, the cross-track error of UUV is gradually converged to zero and has some certain robustness.

  6. An indoor test campaign of the tomography long path differential optical absorption spectroscopy technique.

    Science.gov (United States)

    Mettendorf, K U; Hartl, A; Pundt, I

    2006-02-01

    In this study we validate the two-dimensional long path DOAS tomography measurement technique by means of an indoor experiment with well-known concentration distributions. The experiment was conducted over an area of 10 m x 15 m using one and two cylindrical polycarbonate containers of diameter 2 m, respectively, filled with NO2. The setup was realized with three of the multibeam instruments recently developed by Pundt and Mettendorf (Appl. Opt., 2005, in press), which allow the simultaneous measurement along at least four light paths each. The configuration consisted of twelve simultaneous light beams, 39 horizontal light paths in total, and 18 different cylinder positions inside the field. It was found that for the discretization and inversion technique shown here reconstructions of the concentration distributions from experimental data agree well with simulated reconstructions. In order to draw conclusions for atmospheric applications, numerical studies including instrumental errors were carried out. It was found that with the presented measurement setup it is possible to measure and reconstruct one or two NO2 plumes of 600 m diameter and average concentrations above 4.2 ppbv each, on a scale of 13.5 km2. Theoretical investigations show that it should be possible to localize and quantify 600 m diameter plumes of SO2 > 1.5 ppbv, H2CO > 6.3 ppbv, HONO > 3.2 ppbv, and ozone > 46.2 ppbv. Larger plumes can be measured with higher precision.

  7. Impact of petroleum industry horizontal divestiture on the coal market

    Energy Technology Data Exchange (ETDEWEB)

    Zimmerman, D.L.; Dymond, L.H.; Marris, R.L.

    1979-06-22

    Volume 2 contains appendices as follows: coal supply curves, coal supply model modifications, coal mine financing data, legislative proposals for horizontal divestiture, overview of oil companies in coal industry (including their coal reserves) and the major sources of data and bibliography. (LTN)

  8. Horizontal muon flux measured with the LVD detector at LNGS

    Energy Technology Data Exchange (ETDEWEB)

    Garbini, Marco, E-mail: garbini@bo.infn.it [Museo Storico della Fisica e Centro Studi e Ricerche ' E. Fermi' Roma and INFN Bologna (Italy)

    2011-12-15

    We report the measure of underground horizontal (cos({theta})<0.3) muon flux with the Large Volume Detector (LVD) at the I.N.F.N. Gran Sasso National Laboratory. The analysis is based on the whole muon data collected by LVD since start of data taking in 1992.

  9. The horizontal worldview : A Wittgensteinian attitude towards scientific psychology

    NARCIS (Netherlands)

    van Dijk, Ludger; Withagen, Rob

    2014-01-01

    Many scientific psychologists (implicitly) adopt a vertical worldview. This worldview assumes a layered supervening ontology and thereby invites a reductionist stance on explanation. In the present article we direct attention to an alternative attitude towards reality, the horizontal worldview. We d

  10. Numerical modeling of secondary side thermohydraulics of horizontal steam generator

    Energy Technology Data Exchange (ETDEWEB)

    Melikhov, V.I.; Melikhov, O.I.; Nigmatulin, B.I. [Research and Engineering Centre of LWR Nuclear Plants Safety, Moscow (Russian Federation)

    1995-12-31

    A mathematical model for the transient three-dimensional secondary side thermal hydraulics of the horizontal steam generator has been developed. The calculations of the steam generator PGV-1000 and PGV-4 nominal regimes and comparison of numerical and experimental results have been carried out. 7 refs.

  11. A fala de adolescentes marginais em Belo Horizonte

    Directory of Open Access Journals (Sweden)

    Vera Lúcia Menezes de Oliveira Paiva

    2012-02-01

    Full Text Available Th1s paper discusses some research resulta on sex differences ln the speech of homeless adolescents ln Belo Horizonte. The study showed that male speakers use more standard forms than female speakers, although the inicial hypothesis predicted that groups with a great many characteristics ln common would present little d1fferences concerning prestige forms.

  12. Stereo PIV Experiments on Horizontal Axis Wind Turbine Rotor Model

    NARCIS (Netherlands)

    Akay, B.; Micallef, D.; Ferreira, C.S.; Van Bussel, G.J.W.

    2011-01-01

    This paper sets out to describe the measurements and computations to construct three components of velocity field around the blade. The primary aim of the measurements was to gain insight into the physics of the flow field produced by a horizontal axis wind turbine-HAWT blade. Stereo Particle Image

  13. Horizontal or vertical photobioreactors? How to improve microalgae photosynthetic efficiency

    NARCIS (Netherlands)

    Cuaresma, M.; Janssen, M.G.J.; Vilchez, C.; Wijffels, R.H.

    2011-01-01

    The productivity of a vertical outdoor photobioreactor was quantitatively assessed and compared to a horizontal reactor. Daily light cycles in southern Spain were simulated and applied to grow the microalgae Chlorella sorokiniana in a flat panel photobioreactor. The maximal irradiance around noon di

  14. Global Analysis of Horizontal Gene Transfer in Fusarium verticillioides

    Science.gov (United States)

    The co-occurrence of microbes within plants and other specialized niches may facilitate horizontal gene transfer (HGT) affecting host-pathogen interactions. We recently identified fungal-to-fungal HGTs involving metabolic gene clusters. For a global analysis of HGTs in the maize pathogen Fusarium ve...

  15. Effect of horizontal pick and place locations on shoulder kinematics

    NARCIS (Netherlands)

    Könemann, R.; Bosch, T.; Kingma, I.; Dieën, J.H. van; Looze, M.P. de

    2015-01-01

    In this study the effects of horizontal bin locations in an order picking workstation on upper arm elevation, trunk inclination and hand use were investigated. Eight subjects moved (self-paced) light or heavy products (0.2 and 3.0 kg) from a central product bin to an inner or outer order bin (at 60

  16. Increasing of horizontal velocity of particles leaving a belt conveyor

    Directory of Open Access Journals (Sweden)

    Tavares Abraão

    2017-01-01

    Full Text Available We investigate the transport of granular materials by a conveyor belt via numerical simulations. We report an unusual increasing of particles horizontal velocity when they leave the belt and initiate free-fall. Using Discrete Elements Method, the mechanism underlying this phenomenon were investigated, and a study on how particle and system properties influences this effect were conducted.

  17. Horizontal interactions as the source of CP violation

    Energy Technology Data Exchange (ETDEWEB)

    Decker, R.; Gerard, J.M.; Zoupanos, G.

    1984-03-22

    Assuming that horizontal interactions are the main source of CP violation, we find that their typical effective coupling constant is Gsub(H)proportional10/sup -16/ GeV/sup -2/. Moreover, this source is then of superweak type and the electric dipole moment of the neutron has to be larger than 10/sup -28/ e cm.

  18. The Horizontal Branch of the Sculptor Dwarf galaxy

    NARCIS (Netherlands)

    Salaris, Maurizio; Boer, Thomas de; Tolstoy, Eline; Fiorentino, Giuliana; Cassisi, Santi

    2013-01-01

    We have performed the first detailed simulation of the horizontal branch of the Sculptor dwarf spheroidal galaxy by means of synthetic modelling techniques, taking consistently into account the star formation history and metallicity evolution as determined from the main sequence and red giant branch

  19. Horizontal well performance in Hassi-Messaoud oil field, Algeria

    Energy Technology Data Exchange (ETDEWEB)

    Azzouguen, A.; Mazouzi, A.; Delhomme, A.; Deghmoum, A. [Sonatrach Inc., Hydra, (Algeria)

    2000-11-01

    The performance of non-conventional wells drilled in Hassi-Messaoud field in Algeria was analyzed using a pressure transient analysis technique called Tiab's direct synthesis (TDS). This technique makes it possible to determine the permeability tensor and the effective length of horizontal wells. Transient tests were analyzed using the TDS method for 33 non-conventional wells. For the first time it was possible to obtain the permeability tensor and the vertical permeability anisotropy. Future horizontal well drilling can now be optimized through sensitivity studies. The performance of slanted horizontal and multilateral wells was also compared. It was determined that because of their low risk, slanted wells are more appropriate for the Hassi-Messaoud field. Besides improving productivity, horizontal wells have the added advantage of providing substantial information regarding the geology of the field. It was determined that the two parameters that control production are the length and the vertical permeability. Several recommendations were presented regarding the well spacing. The recommendations were based on different geological models. 21 refs., 12 figs.

  20. The Resource-Based Horizontal Acquisition Strategy of JBS

    OpenAIRE

    Ronald Jean Degen

    2012-01-01

    This paper examines the resource-based horizontal acquisition strategy of JBS. This strategy transformed a relatively small business that was founded in 1953 (comprising a butcher shop and small abattoir located in a small town in the interior of Brazil) into the world?s biggest meat producer by 2010.

  1. On lifting line analysis of horizontal axis windturbines

    Science.gov (United States)

    Politis, G. K.; Loukakis, T. A.

    A convergent iteration scheme for lifting line performance analysis of horizontal axis windturbines is presented. Lifting line correction factors are introduced and compared with those of Prandtl and Goldstein. Lifting line and strip theory formulations are applied for the calculation of performance for two windturbines. Differences of engineering importance are shown to exist in the prediction of the Power coefficient.

  2. The interconnection between biofilm formation and horizontal gene transfer

    DEFF Research Database (Denmark)

    Madsen, Jonas Stenløkke; Burmølle, Mette; Hansen, Lars H.

    2012-01-01

    Recent research has revealed that horizontal gene transfer and biofilm formation are connected processes. Although published research investigating this interconnectedness is still limited, we will review this subject in order to highlight the potential of these observations because of their beli......Recent research has revealed that horizontal gene transfer and biofilm formation are connected processes. Although published research investigating this interconnectedness is still limited, we will review this subject in order to highlight the potential of these observations because...... of their believed importance in the understanding of the adaptation and subsequent evolution of social traits in bacteria. Here, we discuss current evidence for such interconnectedness centred on plasmids. Horizontal transfer rates are typically higher in biofilm communities compared with those in planktonic states....... Biofilms, furthermore, promote plasmid stability and may enhance the host range of mobile genetic elements that are transferred horizontally. Plasmids, on the other hand, are very well suited to promote the evolution of social traits such as biofilm formation. This, essentially, transpires because plasmids...

  3. Modeling the impact of spatial relationships on horizontal curve safety.

    Science.gov (United States)

    Findley, Daniel J; Hummer, Joseph E; Rasdorf, William; Zegeer, Charles V; Fowler, Tyler J

    2012-03-01

    The curved segments of roadways are more hazardous because of the additional centripetalforces exerted on a vehicle, driver expectations, and other factors. The safety of a curve is dependent on various factors, most notably by geometric factors, but the location of a curve in relation to other curves is also thought to influence the safety of those curves because of a driver's expectation to encounter additional curves. The link between an individual curve's geometric characteristics and its safety performance has been established, but spatial considerations are typically not included in a safety analysis. The spatial considerations included in this research consisted of four components: distance to adjacent curves, direction of turn of the adjacent curves, and radius and length of the adjacent curves. The primary objective of this paper is to quantify the spatial relationship between adjacent horizontal curves and horizontal curve safety using a crash modification factor. Doing so enables a safety professional to more accurately estimate safety to allocate funding to reduce or prevent future collisions and more efficiently design new roadway sections to minimize crash risk where there will be a series of curves along a route. The most important finding from this research is the statistical significance of spatial considerations for the prediction of horizontal curve safety. The distances to adjacent curves were found to be a reliable predictor of observed collisions. This research recommends a model which utilizes spatial considerations for horizontal curve safety prediction in addition to current Highway Safety Manual prediction capabilities using individual curve geometric features.

  4. Stereo PIV Experiments on Horizontal Axis Wind Turbine Rotor Model

    NARCIS (Netherlands)

    Akay, B.; Micallef, D.; Ferreira, C.S.; Van Bussel, G.J.W.

    2011-01-01

    This paper sets out to describe the measurements and computations to construct three components of velocity field around the blade. The primary aim of the measurements was to gain insight into the physics of the flow field produced by a horizontal axis wind turbine-HAWT blade. Stereo Particle Image

  5. Horizontal and Vertical Attentional Orienting in Parkinson's Disease

    Science.gov (United States)

    Nys, Gudrun M. S.; Santens, Patrick; Vingerhoets, Guy

    2010-01-01

    Patients with Parkinson's disease (PD) typically suffer from an asymmetric degeneration of dopaminergic cells in the substantia nigra, resulting in right-sided (RPD) or left-sided (LPD) predominance of motor symptomatology. As the dopaminergic system is also involved in attention, we examined horizontal and vertical orienting of attention in LPD…

  6. On the Turbulent Mixing in Horizontal Axis Wind Turbine Wakes

    NARCIS (Netherlands)

    Lignarolo, L.E.M.

    2016-01-01

    The wake flow of a horizontal axis wind turbine is characterised by lower wind speed and higher turbulence than the free-stream conditions. When clustered in large wind farms, wind turbines regularly operate inside the wake of one or more upstream machines. This is a major cause of energy production

  7. The fourth horizontal project in the mature Algyo Field

    Energy Technology Data Exchange (ETDEWEB)

    Pipicz, V.; Benedek, L.; Palasthy, G.; Barodi, T. [MOL Hungarian Oil and Gas Co. (Hungary); Joshi, S.D. [Joshi Technologies International, Tulsa, OK (United States)

    2002-07-01

    Approximately seventy horizontal wells have been drilled in the course of three successful projects in the mature Algyo Field in Hungary since 1993. Recently, a fourth project has been initiated which includes the drilling of more than twenty new horizontal sections. These horizontal wells kick off existing abandoned wells along the thin oil rim that exists in two high permeability reservoirs with top gas and bottom water. The most significant difference between the two reservoirs is that one has water injection and the other has two layers with strong natural bottom water drive. The former geological and dynamic models for the hydrocarbon field in the Pannonian basin was rebuilt in order to handle the common aquifer of four reservoirs. Based on the new geology, reservoir simulation was used to study the reservoir behaviour, including the forthcoming period of gas cap production. The increase in reserves was matched with the production history to observe the movement of the water oil contact (WOC) with the production and drawdown rates in the future when the horizontal trajectories were planned. The reservoir management focused on maximising the long-term profit of the field by optimal production of the reserves, reducing gas and water coning and by the effective use of depleted gas reservoirs and existing vertical wells. Production rate and recovery was increased by reaching the by-passed hydrocarbon and by increasing the drainage area. 6 refs., 3 tabs., 14 figs.

  8. Strong horizontal photospheric magnetic field in a surface dynamo simulation

    NARCIS (Netherlands)

    SchÜssler, M.; Vögler, A.

    2008-01-01

    Context. Observations with the Hinode spectro-polarimeter have revealed strong horizontal internetwork magnetic fields in the quiet solar photosphere. Aims. We aim to interpret the observations with results from numerical simulations. Methods. Radiative MHD simulations of dynamo action by near-surfa

  9. Horizontal Transfer of Genetic Elements in the Black Aspergilli

    NARCIS (Netherlands)

    Diepeningen, van A.D.

    1999-01-01

    The thesis deals with the horizontal transfer of genetic elements in the black Aspergilli . The black Aspergilli form a complex group of asexual species. All share a characteristic black conidiospore color and the ability to efficiently degrade tannin. Selective isolation of all different black Aspe

  10. Coolant rate distribution in horizontal steam generator under natural circulation

    Energy Technology Data Exchange (ETDEWEB)

    Blagovechtchenski, A.; Leontieva, V.; Mitrioukhin, A. [St. Petersburg State Technical Univ. (Russian Federation)

    1997-12-31

    In the presentation the major factors determining the conditions of NCC (Natural Coolant Circulation) in the primary circuit and in particular conditions of coolant rate distribution on the horizontal tubes of PGV-1000 in NPP with VVER-1000 under NCC are considered. 5 refs.

  11. Determination of horizontal and vertical distribution of tree species in ...

    African Journals Online (AJOL)

    Yomi

    2012-01-24

    Jan 24, 2012 ... tree species in Turkey via Shuttle Radar Topography. Mission ... and 1/100,000 scale Forest Information System database, horizontal and vertical distribution of Pinus .... southern parts of the country, in Thrace, and also near some large ... Initially, infrared aerial photographs of the area at 1/15,000 scale.

  12. What Factors Underlie Vertical and Horizontal Export Diversification

    African Journals Online (AJOL)

    Ritsumeikan Asia Pacific University

    investment on human capital and physical infrastructure through foreign investment as well as domestic ..... ethnic conflicts. Table 6: ..... examining diversification from its vertical and horizontal dimensions and contribute to ...... For instance, Sweden and Finland ...... Baumol, William; Nelson, Richard; and Wolf, Edward. 1994.

  13. Quasispecies theory for horizontal gene transfer and recombination

    Science.gov (United States)

    Muñoz, Enrique; Park, Jeong-Man; Deem, Michael W.

    2008-12-01

    We introduce a generalization of the parallel, or Crow-Kimura, and Eigen models of molecular evolution to represent the exchange of genetic information between individuals in a population. We study the effect of different schemes of genetic recombination on the steady-state mean fitness and distribution of individuals in the population, through an analytic field theoretic mapping. We investigate both horizontal gene transfer from a population and recombination between pairs of individuals. Somewhat surprisingly, these nonlinear generalizations of quasispecies theory to modern biology are analytically solvable. For two-parent recombination, we find two selected phases, one of which is spectrally rigid. We present exact analytical formulas for the equilibrium mean fitness of the population, in terms of a maximum principle, which are generally applicable to any permutation invariant replication rate function. For smooth fitness landscapes, we show that when positive epistatic interactions are present, recombination or horizontal gene transfer introduces a mild load against selection. Conversely, if the fitness landscape exhibits negative epistasis, horizontal gene transfer or recombination introduces an advantage by enhancing selection towards the fittest genotypes. These results prove that the mutational deterministic hypothesis holds for quasispecies models. For the discontinuous single sharp peak fitness landscape, we show that horizontal gene transfer has no effect on the fitness, while recombination decreases the fitness, for both the parallel and the Eigen models. We present numerical and analytical results as well as phase diagrams for the different cases.

  14. Impact of petroleum industry horizontal divestiture on the coal market

    Energy Technology Data Exchange (ETDEWEB)

    Zimmerman, D.L.; Dymond, L.H.; Marris, R.L.

    1979-06-22

    Volume 2 contains appendices as follows: coal supply curves, coal supply model modifications, coal mine financing data, legislative proposals for horizontal divestiture, overview of oil companies in coal industry (including their coal reserves) and the major sources of data and bibliography. (LTN)

  15. Performance of a Horizontal Triple Cylinder Type Pulping Machine

    Directory of Open Access Journals (Sweden)

    Sukrisno Widyotomo

    2011-05-01

    Full Text Available Pulping is one important step in wet coffee processing method. Pulping process usually uses a machine which constructed by wood or metal materials. A horizontal single cylinder type of fresh coffee cherries pulping machine is the most popular machine in coffee processing. One of the weaknesses of a horizontal single cylinder type of fresh coffee cherries pulping machine is higher in broken beans. Broken bean is one of mayor aspects in defect system that contribute to low quality. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal double cylinder type of fresh coffee cherries pulping machine which resulted in 12.6—21.4% of broken beans. To reduce percentage of broken beans, Indonesian Coffee and Cocoa Research Institute has developed and tested a horizontal triple cylinder type of fresh coffee cherries pulping machine. Material tested was fresh mature Robusta coffee cherries, 60—65% (wet basis moisture content; has classified on 3 levels i.e. unsorted, small and medium, and clean from metal and foreign materials. The result showed that the machine produced 6,340 kg/h in optimal capacity for operational conditions, 1400 rpm rotor rotation speed for unsorted coffee cherries with composition 55.5% whole parchment coffee, 3.66% broken beans, and 1% beans in wet skin.Key words : coffee, pulp, pulper, cylinder, quality.

  16. On the Turbulent Mixing in Horizontal Axis Wind Turbine Wakes

    NARCIS (Netherlands)

    Lignarolo, L.E.M.

    2016-01-01

    The wake flow of a horizontal axis wind turbine is characterised by lower wind speed and higher turbulence than the free-stream conditions. When clustered in large wind farms, wind turbines regularly operate inside the wake of one or more upstream machines. This is a major cause of energy production

  17. Equilibrium type of competition with horizontal product innovation

    NARCIS (Netherlands)

    Negriu, A.

    2015-01-01

    Singh and Vives (1984) consider a game where duopolists first commit to a strategic variable quantity or pice, and then compete in selling horizontally differentiated products. Here product substitutability is endogenized by allowing firms to undertake R&D investments to increase differentitation. W

  18. Ekman Spiral in Horizontally Inhomogeneous Ocean with Varying Eddy Viscosity

    Science.gov (United States)

    2015-01-01

    1 Ekman Spiral in Horizontally Inhomogeneous Ocean with Varying Eddy Viscosity...Oceanography Naval Postgraduate School, Monterey, California, USA Manuscript Click here to download Manuscript: Ekman -chu-pageoph-rev.docx 1...currently valid OMB control number. 1. REPORT DATE 2015 2. REPORT TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Ekman Spiral

  19. Device for Horizontal Zone Electrophoresis in Free Electrolyte

    CERN Document Server

    Priemyshev, A N; Bozhikov, G A; Alikov, B A; Salamatin, A V; Furyaev, T A; Maslov, O D; Milanov, M V; Dmitriev, S N

    2000-01-01

    With expansion of area of application of an electromigration method the necessity of modernization of installation for horizontal zone electrophoresis in free electrolyte has appeared. A number of the basic modules was essentially advanced, that has allowed considerably increase reliability and accuracy of received results. The device is completely automated.

  20. HORIZONTE Y ESTRUCTURA DE LA PREGUNTA PEDAGÓGICA

    Directory of Open Access Journals (Sweden)

    Arturo G. Rillo

    2011-01-01

    Full Text Available En este artículo se abren caminos para la reflexión y la investigación de la pregunta pedagógica como un problema hermenéutico sustentado en la dialéctica de la pregunta y la respuesta. El punto de partida se construyó mediante las coordenadas propuestas por Heidegger (punto de mira, dirección de la mirada y horizonte de la mira y los prejuicios que subyacen en la tradición educativa contemporánea. El análisis se proyecta hacia la identificación de la estructura y el horizonte de la pregunta pedagógica confrontando los aportes de Heidegger, Gadamer y Freire en la elaboración de una pedagogía de la pregunta. La estructura de la pregunta incluye lo puesto en cuestión, lo preguntado y lo interrogado, lo que posibilita construir un horizonte para comprender la pregunta pedagógica desde la aproximación del estudiante a los saberes desde una praxis liberadora. Se concluye que la estructura y el horizonte de la pregunta pedagógica se sustentan en la lógica concreta del trabajo hermenéutico, donde la apertura del estudiante a las experiencias y vivencias desvela la construcción de su conocimiento mediante el arte de pensar que deriva de la praxis transformadora.

  1. Lithium-Induced Downbeat Nystagmus and Horizontal Gaze Palsy

    DEFF Research Database (Denmark)

    Jørgensen, Jesper Skovlund; Landschoff Lassen, Lisbeth; Wegener, Marianne

    2016-01-01

    We report a case of lithium-induced downbeat nystagmus and horizontal gaze palsy in a 62-year-old woman who was treated for a bipolar affective disorder with lithium carbonate for one month. At presentation serum lithium was within therapeutic range. No alternative causes of the ocular motility...... disturbances were found, and the patient improved significantly as lithium carbonate was discontinued....

  2. Freight transportation efficiency through horizontal cooperation in Flanders

    NARCIS (Netherlands)

    Cruijssen, F.C.A.M.; Dullaert, W.; Joro, T.

    2010-01-01

    This paper describes a practical application of data envelopment analysis (DEA) to the Flemish road transportation sector. The efficiency of 82 road transportation companies responding to a large-scale survey focused on horizontal cooperation is evaluated, based on two inputs and two outputs.

  3. On Charge Quantization and Abelian Gauge Horizontal Symmetries

    CERN Document Server

    Epele, L N; Ponce, W A; Ponce, William A.

    1997-01-01

    Under the assumption that there exists a local gauge horizontal symmetry $G_H$ wich allows only for a top quark mass at tree level, we look for the constraints that charge quatization and the family structure of the standard model imposes on that symmetry.

  4. Direct Numerical Simulation Sediment Transport in Horizontal Channel

    Energy Technology Data Exchange (ETDEWEB)

    Uhlmann, M.

    2006-07-01

    We numerically simulate turbulent flow in a horizontal plane channel over a bed of mobile particles. All scales of fluid motion are resolved without modeling and the phase interface is accurately represented. Our results indicate a possible scenario for the onset of erosion through collective motion induced by buffer-layer streaks. (Author) 27 refs.

  5. Freight transportation efficiency through horizontal cooperation in Flanders

    NARCIS (Netherlands)

    Cruijssen, F.C.A.M.; Dullaert, W.; Joro, T.

    2010-01-01

    This paper describes a practical application of data envelopment analysis (DEA) to the Flemish road transportation sector. The efficiency of 82 road transportation companies responding to a large-scale survey focused on horizontal cooperation is evaluated, based on two inputs and two outputs. Variou

  6. FLIGHT PATH CONTROL FOR UNMANNED AERIAL VEHICLE

    Directory of Open Access Journals (Sweden)

    M. A. Al-Mashhadani

    2014-01-01

    Full Text Available Studying the optimized control law specified criteria on UAV while hovering over a path defined by the reference points in the inertial frame. An illustrative example is the  theoretical efficiency of the proposed provisions. 

  7. Stochastic Evolutionary Algorithms for Planning Robot Paths

    Science.gov (United States)

    Fink, Wolfgang; Aghazarian, Hrand; Huntsberger, Terrance; Terrile, Richard

    2006-01-01

    A computer program implements stochastic evolutionary algorithms for planning and optimizing collision-free paths for robots and their jointed limbs. Stochastic evolutionary algorithms can be made to produce acceptably close approximations to exact, optimal solutions for path-planning problems while often demanding much less computation than do exhaustive-search and deterministic inverse-kinematics algorithms that have been used previously for this purpose. Hence, the present software is better suited for application aboard robots having limited computing capabilities (see figure). The stochastic aspect lies in the use of simulated annealing to (1) prevent trapping of an optimization algorithm in local minima of an energy-like error measure by which the fitness of a trial solution is evaluated while (2) ensuring that the entire multidimensional configuration and parameter space of the path-planning problem is sampled efficiently with respect to both robot joint angles and computation time. Simulated annealing is an established technique for avoiding local minima in multidimensional optimization problems, but has not, until now, been applied to planning collision-free robot paths by use of low-power computers.

  8. Path Planning in a Dynamic Environment

    Directory of Open Access Journals (Sweden)

    Mohamed EL KHAILI

    2014-08-01

    Full Text Available Path planning is an important area in the control of autonomous mobile robots. Recent work has focused on aspects reductions in processing time than the memory requirements. A dynamic environment uses a lot of memory and hence the processing time increases too. Our approach is to reduce the processing time by the use of a pictorial approach to reduce the number of data used. In this paper, we present a path planning approach that operates in three steps. First, a construction of the visibility tree is performed. The following treatments are not performed on the original image but on the result tree whose elements are specific points of the environment linked by the relationship of visibility. We construct thereafter a visibility graph which one seeks the shortest path. This approach has a great interest because of its fast execution speed. The path search is extended also for the case where obstacles can move. The moving obstacles may be other mobile robots whose trajectories and speeds are known initially. At the end, some applications are provided on solving similar problem such civil aviation in order to guide plane avoiding collisions.

  9. Predictors of Retirement Satisfaction: A Path Model.

    Science.gov (United States)

    Kremer, Yael

    1985-01-01

    Examined adjustment to retirement among 310 former industrial and service workers. Respondents had come to terms with retirement and enjoyed their more relaxed lifestyle. Dominant variables in the path model were retirees' satisfaction with specific aspects of retirement: giving up work, activities with family and friends, rest, and free time. (BH)

  10. Learning paths and OER: trends and opportunities

    NARCIS (Netherlands)

    Janssen, José; Berlanga, Adriana; Koper, Rob

    2013-01-01

    Janssen, J., Berlanga, A. J., & Koper, R. (2013). Learning paths and OER: trends and opportunities. In R. Jacobi, H. Jelgerhuis, & N. van der Woert (Eds.), Trendreport Open Educational Resources 2013 (pp. 76-80). Utrecht: SURF Foundation - Special Interest Group Open Educational Resources SURF. Fina

  11. Demixing light paths inside disordered metamaterials

    NARCIS (Netherlands)

    Vellekoop, Ivo Micha; van Putten, E.G.; Putten, E.G.; Lagendijk, Aart; Mosk, Allard

    2008-01-01

    We experimentally demonstrate the first method to focus light inside disordered photonic metamaterials. In such materials, scattering prevents light from forming a geometric focus. Instead of geometric optics, we used multi-path interference to make the scattering process itself concentrate light on

  12. Bead-Fourier path integral molecular dynamics

    Science.gov (United States)

    Ivanov, Sergei D.; Lyubartsev, Alexander P.; Laaksonen, Aatto

    2003-06-01

    Molecular dynamics formulation of Bead-Fourier path integral method for simulation of quantum systems at finite temperatures is presented. Within this scheme, both the bead coordinates and Fourier coefficients, defining the path representing the quantum particle, are treated as generalized coordinates with corresponding generalized momenta and masses. Introduction of the Fourier harmonics together with the center-of-mass thermostating scheme is shown to remove the ergodicity problem, known to pose serious difficulties in standard path integral molecular dynamics simulations. The method is tested for quantum harmonic oscillator and hydrogen atom (Coulombic potential). The simulation results are compared with the exact analytical solutions available for both these systems. Convergence of the results with respect to the number of beads and Fourier harmonics is analyzed. It was shown that addition of a few Fourier harmonics already improves the simulation results substantially, even for a relatively small number of beads. The proposed Bead-Fourier path integral molecular dynamics is a reliable and efficient alternative to simulations of quantum systems.

  13. Unified classical path theories of pressure broadening.

    Science.gov (United States)

    Bottcher, C.

    1971-01-01

    Derivation of a unified classical path theory of pressure broadening, using only elementary concepts. It is shown that the theory of Smith, Cooper and Vidal (1969) is only correct at all frequencies to first order in the number density of perturbers.

  14. Path-breaking books in regional science

    NARCIS (Netherlands)

    Waldorf, BS

    2004-01-01

    This article presents a collection of regional science books that long-standing members of the Regional Science Association International (RSAI) identified as path-breaking books. The most frequently nominated books include the "classics" by Isard, the seminal books in urban economics by Alonso, Mut

  15. Transition paths in molecules at finite temperature

    Science.gov (United States)

    Pinski, F. J.; Stuart, A. M.

    2010-05-01

    In the zero temperature limit, it is well known that in systems evolving via Brownian dynamics, the most likely transition path between reactant and product may be found as a minimizer of the Freidlin-Wentzell action functional. An analog for finite temperature transitions is given by the Onsager-Machlup functional. The purpose of this work is to investigate properties of Onsager-Machlup minimizers. We study transition paths for thermally activated molecules governed by the Langevin equation in the overdamped limit of Brownian dynamics. Using gradient descent in pathspace, we minimize the Onsager-Machlup functional for a range of model problems in one and two dimensions and then for some simple atomic models including Lennard-Jones seven-atom and 38-atom clusters, as well as for a model of vacancy diffusion in a planar crystal. Our results demonstrate interesting effects, which can occur at nonzero temperature, showing transition paths that could not be predicted on the basis of the zero temperature limit. However the results also demonstrate unphysical features associated with such Onsager-Machlup minimizers. As there is a growing literature that addresses transition path sampling by related techniques, these insights add a potentially useful perspective into the interpretation of this body of work.

  16. Star-Paths, Stones and Horizon Astronomy

    Science.gov (United States)

    Brady, Bernadette

    2015-05-01

    Archaeoastronomers tend to approach ancient monuments focusing on the landscape and the horizon calendar events of sun and moon and, due to problems with precession, generally ignore the movement of the stars. However, locating the position of solar calendar points on the horizon can have other uses apart from calendar and/or cosmological purposes. This paper firstly suggests that the stars do not need to be ignored. By considering the evidence of the Phaenomena, a sky poem by Aratus of Soli, a third century BC Greek poet, and his use of second millennium BC star lore fragments, this paper argues that the stars were a part of the knowledge of horizon astronomy. Aratus' poem implied that the horizon astronomy of the late Neolithic and Bronze Age periods included knowledge of star-paths or 'linear constellations' that were defined by particular horizon calendar events and other azimuths. Knowledge of such star-paths would have enabled navigation and orientation, and by using permanent markers, constructed or natural, to define these paths, they were immune to precession as the stones could redefine a star-path for a future generation. Finally the paper presents other possible intentions behind the diverse orientation of passage tombs and some megalithic sites.

  17. Demixing light paths inside disordered metamaterials

    NARCIS (Netherlands)

    Vellekoop, I.M.; Putten, E.G.; Lagendijk, A.; Mosk, A.P.

    2008-01-01

    We experimentally demonstrate the first method to focus light inside disordered photonic metamaterials. In such materials, scattering prevents light from forming a geometric focus. Instead of geometric optics, we used multi-path interference to make the scattering process itself concentrate light on

  18. Damage detection using frequency shift path

    Science.gov (United States)

    Wang, Longqi; Lie, Seng Tjhen; Zhang, Yao

    2016-01-01

    This paper introduces a novel concept called FREquency Shift (FRESH) path to describe the dynamic behavior of structures with auxiliary mass. FRESH path combines the effects of frequency shifting and amplitude changing into one space curve, providing a tool for analyzing structure health status and properties. A damage index called FRESH curvature is then proposed to detect local stiffness reduction. FRESH curvature can be easily adapted for a particular problem since the sensitivity of the index can be adjusted by changing auxiliary mass or excitation power. An algorithm is proposed to adjust automatically the contribution from frequency and amplitude in the method. Because the extraction of FRESH path requires highly accurate frequency and amplitude estimators; therefore, a procedure based on discrete time Fourier transform is introduced to extract accurate frequency and amplitude with the time complexity of O (n log n), which is verified by simulation signals. Moreover, numerical examples with different damage sizes, severities and damping are presented to demonstrate the validity of the proposed damage index. In addition, applications of FRESH path on two steel beams with different damages are presented and the results show that the proposed method is valid and computational efficient.

  19. Quad-rotor flight path energy optimization

    Science.gov (United States)

    Kemper, Edward

    Quad-Rotor unmanned areal vehicles (UAVs) have been a popular area of research and development in the last decade, especially with the advent of affordable microcontrollers like the MSP 430 and the Raspberry Pi. Path-Energy Optimization is an area that is well developed for linear systems. In this thesis, this idea of path-energy optimization is extended to the nonlinear model of the Quad-rotor UAV. The classical optimization technique is adapted to the nonlinear model that is derived for the problem at hand, coming up with a set of partial differential equations and boundary value conditions to solve these equations. Then, different techniques to implement energy optimization algorithms are tested using simulations in Python. First, a purely nonlinear approach is used. This method is shown to be computationally intensive, with no practical solution available in a reasonable amount of time. Second, heuristic techniques to minimize the energy of the flight path are tested, using Ziegler-Nichols' proportional integral derivative (PID) controller tuning technique. Finally, a brute force look-up table based PID controller is used. Simulation results of the heuristic method show that both reliable control of the system and path-energy optimization are achieved in a reasonable amount of time.

  20. Path-breaking books in regional science

    NARCIS (Netherlands)

    Waldorf, BS

    2004-01-01

    This article presents a collection of regional science books that long-standing members of the Regional Science Association International (RSAI) identified as path-breaking books. The most frequently nominated books include the "classics" by Isard, the seminal books in urban economics by Alonso, Mut