International Nuclear Information System (INIS)
Lehrman, I.S.; Colestock, P.L.; McNeill, D.H.; Greene, G.J.; Bernabei, S.; Hosea, J.C.; Ono, M.; Shohet, J.L.; Wilson, J.R.
1989-04-01
Edge measurements have been conducted on the PLT tokamak under a variety of operating conditions in order to ascertain the relevant processes at work in coupling rf power to plasmas. The edge density is found to increase significantly with the application of ICRF, and electron heating occurs in the vicinity of the Faraday shield surrounding the antenna. Spectroscopic measurements indicate that the energized antenna is a significant particle source. The relative increase of metallic impurities was found to be /approximately/2.7 times larger than the corresponding increase in deuterium. In addition, the relative increase of deuterium and impurities was /approximately/3--4 times greater at the energized antenna than at other locations around the torus. Model calculations show that for deuterium released from the Faraday shield, the D/sub α/ emission is localized radially to a region within 4 cm of the antenna. A correlation was found between the edge density and the D/sub α/ intensity that justifies its use as a measure of the particle source rate. 26 refs., 14 figs
Turbomolecular pump vacuum system for the Princeton Large Torus
International Nuclear Information System (INIS)
Dylla, H.F.
1977-10-01
A turbomolecular pump vacuum system has been designed and installed on the Princeton Large Torus (PLT). Four vertical shaft, oil-bearing, 1500 l/s turbomolecular pumps have been interfaced to the 6400 liter PLT Vacuum vessel to provide a net pumping speed of 3000 l/s for H 2 . The particular requirements and problems of tokamak vacuum systems are enumerated. A vacuum control system is described which protects the vacuum vessel from contamination, and protects the turbomolecular pumps from damage under a variety of possible failure modes. The performance of the vacuum system is presented in terms of pumping speed measurements and residual gas behavior
International Nuclear Information System (INIS)
Thompson, P.A.
1975-01-01
DA/PLT, the data acquisition system for the Princeton Large Torus (PLT) fusion research device, consists of a PDP-10 host computer, five satellite PDP-11s connected to the host by a special high-speed interface, miscellaneous other minicomputers and commercially supplied instruments, and much PPPL produced hardware. The software consists of the standard PDP-10 monitor with local modifications and the special systems and applications programs to customize the DA/PLT for the specific job of supporting data acquisition, analysis, display, and archiving, with concurrent off-line analysis, program development, and, in the background, general batch and timesharing. Some details of the over-all architecture are presented, along with a status report of the different PLT experiments being supported
PLT neutral beam injection systems
International Nuclear Information System (INIS)
Menon, M.M.; Barber, G.C.; Blue, C.W.
1979-01-01
A brief description of the Princeton Large Torus (PLT) neutral beam injection system is given and its performance characteristics are outlined. A detailed operational procedure is included, as are some tips on troubleshooting. Proper operation of the source is shown to be a crucial factor in system performance
Regimes of operation in the Princeton Large Torus
Energy Technology Data Exchange (ETDEWEB)
Hosea, J.C.
1979-10-01
In the quest for optimum discharge conditions in the Princeton Large Torus (PLT), a variety of discharge regimes have been produced. These separate broadly into two main categories - those regimes with m greater than or equal to 2 oscillatory MHD instabilities and often hollow electron profiles for tungsten limiters, and those regimes for which the electron temperature is sufficiently peaked to support the internal sawtooth or near-sawtooth (m = 1) instability. The internal sawtooth regime is found to be optimum for confinement but to be more difficult to select when low-Z impurity concentrations have been reduced with low power discharge cleaning or gettering to permit extension of the high density operation limit. Gas programming is used to cool the plasma periphery, thereby reducing the high-Z impurity concentrations and causing the current channel to constrict into the sawtooth regime, and then to attain the desired plasma density. With discharges selected in this manner, gross energetic confinement times up to approx. 100 msec have been obtained at densities of approx. 10/sup 14/ cm/sup -3/, and very high ion and electron temperatures have been produced with neutral beam injection heating at lower densities with no observable deleterious effect on energy confinement.
Deuterium implantation in first wall candidate materials by exposure in the Princeton large torus
Energy Technology Data Exchange (ETDEWEB)
Chang, J.; Tobin, A. (Grumman Aerospace Corp., Bethpage, NY (USA). Research and Development Center); Manos, D. (Princeton Univ., NJ (USA). Plasma Physics Lab.)
Titanium alloys are of interest as a first wall material in fusion reactors because of their excellent thermophysical and thermomechanical properties. A major concern with their application to the first wall is associated with the known affinity of titanium for hydrogen and the related consequences for fuel recycling, tritium inventory, and hydrogen embrittlement. Little information exists on trapping and release of hydrogen isotopes implanted at energies below 500 eV. This work was undertaken to measure hydrogen isotope trapping and release at the first wall of the Princeton Large Torus Tokamak (PLT).
Application data for the PLT stabilizing field rectifier
International Nuclear Information System (INIS)
Bronner, G.; Murray, J.G.; Oliaro, G.E.
1975-11-01
This paper describes the 12-pulse stabilizing field rectifier used for vertical field production in the Princeton Large Torus (PLT). It is essential that the rectifier be reliable, and protect itself from all faults including induced transient overvoltage produced by switching and plasma instabilities. To this end, computer simulations were run to insure protection under various fault conditions
Piotron at SIN - a large superconducting double torus spectrometer
International Nuclear Information System (INIS)
Horvath, I.; Vecsey, G.; Zellweger, J.
1981-01-01
A test facility for radiation therapy with negative /pi/-mesons was constructed in Switzerland. The facility is a large double torus spectrometer similar to the Stanford design. For variation of stopping depth different momenta are selected by variation of the magnetic field. Superconducting ac magnets are necessary for tumor scanning and represent a major part of such a facility. Main design features and performance are reported. 10 refs
International Nuclear Information System (INIS)
Goldston, R.J.; Kaita, R.; Beiersdorfer, P.; Gammel, G.; Herndon, D.L.; McCune, D.C.; Meyerhofer, D.D.
1987-01-01
The horizontally scanning, multi-angle charge exchange analysers on the Princeton Large Torus (PLT) and the Poloidal Divertor Experiment (PDX) were used to study the effects of MHD activity on the background ion distribution function and on the beam ion slowing-down process during high power neutral injection. Sawtooth oscillations were observed in the fast ion flux on PLT and PDX, and measurements with neutral beams providing local neutral density enhancement indicated that the ions were transported radially when these events occurred. With near-perpendicular injection in PDX, at the lower toroidal fields necessary to maximize the plasma beta, repetitive bursts of greatly enhanced charge exchange flux were observed. These were associated with the 'fishbone' MHD instability, and a substantial depletion of the perpendicular slowing-down spectrum below the injection energy was seen. A simple phenomenological model for this loss mechanism was developed, and its use in simulation codes has been successful in providing good agreement with the experimental data. The behaviour and characteristics of this model are well matched by direct theoretical calculations. (author)
Component design description of the neutral beam injectors for PLT
International Nuclear Information System (INIS)
Johnson, R.L.; Baer, M.B.; Dagenhart, W.K.; Haselton, H.H.; Mann, T.L.; Queen, C.C.; Stirling, W.L.; Whitfield, P.W.
1977-01-01
Plasma heating by injection of high energy neutrals is one of the experiments to be carried out on Princeton Large Torus (PLT). A four unit neutral beam injection system has been designed, built and tested which should inject a total of 3 MW of neutrals into PLT with a 200 millisecond pulse length. A typical system unit is described where the major components are identified. The following discussion describes each of these items along with some details of the design and fabrication problems encountered. Some early design considerations addressed the problems of separation and dumping of residual ions from the neutral beam, calorimetry of the neutrals with incident fuxes of 25 KW/cm 2 , and pumping speeds of several hundred thousand liters per second for hydrogen gas. Solutions were found for these problems while also resolving the complex dilemma of interfacing four large systems to a tokamak
Data acquisition system for PLT Neutral Beam Test Stand
International Nuclear Information System (INIS)
Francis, J.E. Jr.; Hammons, C.E.
1977-01-01
The PLT Neutral Beam Test Stand at Oak Ridge National Laboratory was constructed to test and condition powerful neutral beam sources for the Princeton Large Torus experiment at Princeton Plasma Physics Laboratory. The data acquisition system for the test stand monitors the beam characteristics and power output to determine if the beam is operating at its design specifications. The high speed of the computer system is utilized to provide near-real-time analysis of experimental data. The analysis of the data is presented as numerical tabulation and graphic display
International Nuclear Information System (INIS)
Goldston, R.J.; Kaita, R.; Beiersdorfer, P.; Gammel, G.; Herndon, D.L.; McCune, D.C.; Meyerhofer, D.D.
1986-07-01
The horizontally scanning, multiangle charge-exchange analyzers on the Princeton Large Torus (PLT) and the Poloidal Divertor Experiment (PDX) were used to study the effects of MHD activity on the background ion distribution function and on the beam ion slowing-down process during high-power neutral injection. Sawtooth oscillations were observed in the fast ion flux on PLT and PDX, and measurements with neutral beams providing local neutral density enhancement indicate that ions are transported radially when these events occur. With near-perpendicular injection in PDX, at the lower toroidal fields necessary to maximize beta, rapid, repetitive bursts of greatly enhanced charge-exchange flux were observed. These are associated with the ''fishbone'' MHD instability, and a substantial depletion of the perpendicular slowing-down spectrum below the injection energy was seen. A simple phenomenological model for this loss mechanism was developed, and its use in simulation codes has been successful in providing good agreement with the data. The behavior and characteristics of this model are well matched by the direct theoretical calculations
Hierarchical Cantor set in the large scale structure with torus geometry
Energy Technology Data Exchange (ETDEWEB)
Murdzek, R. [Physics Department, ' Al. I. Cuza' University, Blvd. Carol I, Nr. 11, Iassy 700506 (Romania)], E-mail: rmurdzek@yahoo.com
2008-12-15
The formation of large scale structures is considered within a model with string on toroidal space-time. Firstly, the space-time geometry is presented. In this geometry, the Universe is represented by a string describing a torus surface. Thereafter, the large scale structure of the Universe is derived from the string oscillations. The results are in agreement with the cellular structure of the large scale distribution and with the theory of a Cantorian space-time.
Non-superconducting magnet structures for near-term, large fusion experimental devices
International Nuclear Information System (INIS)
File, J.; Knutson, D.S.; Marino, R.E.; Rappe, G.H.
1980-10-01
This paper describes the magnet and structural design in the following American tokamak devices: the Princeton Large Torus (PLT), the Princeton Divertor Experiment (PDX), and the Tokamak Fusion Test Reactor (TFTR). The Joint European Torus (JET), also presented herein, has a magnet structure evolved from several European programs and, like TFTR, represents state of the art magnet and structure design
International Nuclear Information System (INIS)
Namsrai, Kh.
2001-11-01
Geometrical structure and physical characteristics of a torus are investigated in detail. Newtonian and electromagnetic potentials of the torus are defined at short and long distances. It is shown that torus potential at small distances has attractive oscillator behaviour. Motion of a particle in the torus potential is studied. The inertia tensor of the torus and its dynamics are obtained. Rotating torus whose tip is held fixed by two massless rigid threads and moves in a gravitational field is considered. (author)
Observations of giant recombination edges on PLT tokamak induced by particle transport
International Nuclear Information System (INIS)
Brau, K.; von Goeler, S.; Bitter, M.; Cowan, R.D.; Eames, D.; Hill, K.; Sauthoff, N.; Silver, E.; Stodiek, W.
1980-03-01
Characteristic steps in the continum spectrum of high temperature tokamak plasmas associated with recombination radiation from impurity ions were observed. During special argon-seeded discharges on the Princeton Large Torus (PLT) tokamak the x-ray spectrum exhibited large enhancements over the bremsstrahlung continuum beginning with energies of 4.1 keV. This corresponds to the radiative capture of free electrons by hydrogen-like argon into the ground state of helium-like argon. A simple particle diffusion model is proposed, with the Ar XVIII radial profiles evaluated from the size of the recombination edges. For the case of moderate density ( approx. 3 x 10 13 cm -3 ) and temperature [T/sub e/(0) approx. 1.5 keV] discharges the outward radial transport velocity is found to be approximately 10 m/sec
DuoPIGatron ion sources for PLT injectors
International Nuclear Information System (INIS)
Tsai, C.C.; Stirling, W.L.; Haselton, H.H.; Davis, R.C.; Schechter, D.E.
1977-01-01
Plasma heating requirements for the Princeton Large Torus (PLT) are set at about 1 MJ total beam energy for 3 MW beam power of energetic hydrogen (or deuterium) neutrals at 40 keV. To fulfill this design goal from four neutral beam injectors, the duoPlGatron ion source originally developed at ORNL has been modified, developed, and scaled-up to versions with 20-cm and/or 22-cm grid diameters. Utilizing the multipole line cusp magnetic field confinement for the ionizing electrons and created Philips Ionization Gauge (PIG) plasma, these sources generate a uniform (+-5 percent density variation over 23-cm diam) and dense plasma (about 2 x 10 12 cm 3 at the extraction surface). Such sources have been operated reliably to deliver a beam current exceeding 70 A of hydrogen ions at 40 keV. For such a beam condition the source is capable of running with an arc pulse of 0.5 sec. Moreover, the corresponding arc efficiency is very high, below 1.0 KW arc power per ampere of ion beam current. In this paper we describe the plasma generation, source characteristics and arc efficiency as functions of magnetic fields, gas pressure, and arc power (including the arc voltage and current). The other exciting feature, high proton yield (exceeding 80 percent), will be discussed
International Nuclear Information System (INIS)
Hosea, J.; Wilson, J.R.; Hooke, W.
1986-01-01
A variety of rf experiments are being conducted on PLT in order to explore rf techniques which could improve tokamak performance parameters. Of special importance are the studies of ion Bernstein wave (IBW) heating, lower hybrid MHD stabilization and electron heating, down-shifted electron cyclotron heating, and fast wave current drive. Ion Bernstein wave heating results at modest power indicate that the particle confinement time could be enhanced relative to that for fast wave heating in the ion cyclotron range of frequencies (ICRF) and neutral beam heating. At these power levels a conclusive determination of energy confinement scaling with power cannot yet be given. Central sawtooth and m = 1 MHD stabilization is being obtained with centrally peaked lower hybrid (LH) current drive and the central electron temperature is peaking to values (approx.5 keV) well outside the bounds of ''profile consistency.'' In this case the electron energy confinement is apparently increased relative to the ohmic value. The production of relativistic electrons via heating at the down-shifted electron cyclotron (EC) frequency is found to be consistent with theoretical predictions and lends support to the use of this method for heating in relatively high magnetic field devices
International Nuclear Information System (INIS)
Hammett, G.W.; Kaita, R.; Wilson, J.R.
1988-01-01
Ion cyclotron radiofrequency heating experiments were performed with a 3 He minority ion species in a 4 He majority plasma in the Princeton Large Torus. The energetic 3 He ion 'tail' was measured directly with a charge exchange neutral analyser for the first time. Comparisons with bounce averaged quasi-linear calculations suggest a modestly peaked radiofrequency power deposition profile. The double charge exchange process 3 He ++ + 4 He o -> 3 He o + 4 He ++ demonstrated in these measurements may be useful as part of an alpha particle diagnostic in a fusion reactor experiment. (author). 21 refs, 4 figs
Fast-wave ion cyclotron heating in the Princeton Large Torus
International Nuclear Information System (INIS)
Hosea, J.; Boyd, D.; Bretz, N.
1981-01-01
Recent experimental results for ICRF heating in PLT are presented. For the two-ion regime in D-H or D- 3 He plasmas minority H and 3 He ions are found to absorb the RF power and transfer it to the deuterons and electrons in accordance with Fokker-Planck theory. The deuteron heating rate is approximately 3eVx10 13 cm -3 .kW for H and approximately 6eVx10 13 cm -3 .kW for 3 He minorities. Neutron fluxes of approximately 3x10 11 s -1 corresponding to a Tsub(d) approximately 2keV (ΔTsub(d) approximately 1.2keV) have been produced with Psub(RF) approximately 620kW at anti nsub(e) approximately 2.9x10 13 cm -3 . Neutron energy spectra and mass-sensitive charge-exchange spectra indicate Maxwellian deuteron distributions. In addition, D- 3 He fusion reaction rates approximately >10 12 s -1 have been produced by the energetic 3 He ions. For the second-harmonic regime, initial heating results for an H plasma at Psub(RF) approximately 140kW are consistent with the Fokker-Planck theory, and the bulk heating rate is comparable with that of D-heating in the D-H minority regime. (author)
Fast-wave ion-cyclotron heating in the Princeton Large Torus
International Nuclear Information System (INIS)
Hosea, J.; Boyd, D.; Bretz, N.
1981-02-01
Recent experimental results for ICRF heating in PLT are presented. For the two-ion regime in D-H or D- 3 He plasmas minority H and 3 He ions are found to absorb the rf power and transfer it to the deuterons and electrons in accordance with Fokker-Planck theory. The deuteron heating rate is approx. 3 eV x 10 13 cm -3 /kW for H and approx. 6 eV x 10 13 cm -3 /kW for 3 He minorities. Neutron fluxes of approx. 3 x 10 11 sec -1 corresponding to a T/sub d/ approx. 2 keV (ΔT/sub d/ approx. 1.2 keV) have been produced with P/sub rf/ approx. = 620 kW at anti n/sub e/ approx. = 2.9 x 10 13 cm -3 . Neutron energy spectra and mass sensitive charge exchange spectra indicate Maxwellian deuteron distributions. In addition, D- 3 He fusion reaction rates greater than or equal to 10 12 sec -1 have been produced by the energetic 3 He ions. For the second harmonic regime, initial heating results for an H plasma at P/sub rf/ approx. = 140 kW are consistent with the Fokker-Planck theory and the bulk heating rate is comparable to that of D heating in the D-H minority regime
Lifetime of the phonons in the PLT ceramic
Energy Technology Data Exchange (ETDEWEB)
Barba-Ortega, J., E-mail: jjbarba@unal.edu.co; Joya, M. R., E-mail: mrinconj@unal.edu.co [Departamento de Física, Universidad Nacional de Colombia, carrera 30 # 45-03, Bogotá 1149 (Colombia); Londoño, F. A., E-mail: flondono@fisica.udea.edu.co [Instituto de Física, Universidad de Antioquia, Calle 67 #53-108 Of.6-105, Medellin (Colombia)
2014-11-05
The lifetimes at higher temperatures on lanthanum-modified lead titanate (PLT) are mainly due to the anharmonic decay of optical phonons into low-energy phonons. The temperature-independent contributions from inherent crystal defects and from boundary scattering become comparable to the phonon scattering contribution at lower temperatures. The thermal interaction is large at higher temperatures which decreases the phonon mean free path, and so the decay lifetime decreases as the temperature of the system is increased. This leads to the increased line width at higher temperatures. We made an estimate of the lifetimes for different concentrations and temperatures in PLT.
International Nuclear Information System (INIS)
Marino, R.
1975-11-01
The assembly of the PLT device began in June 1974 with a preassembly of the mechanical structure at a remote site. The preassembly sequence incorporated final fabrication procedures with an initial staging operation. This successful staging/fabrication procedure proved to be an invaluable asset when the final assembly was started in August 1974. The assembly continued with the initial reassembly of the previously tested structural components at the final machine site. Construction was interrupted at several points to allow for toroidal field coil, vacuum vessel, and poloidal coil installation. Two phases of toroidal field coil power tests were included in the assembly sequence prior to, and just after the vacuum vessel insertion
Spherical Torus Plasma Interactions with Large-area Liquid Lithium Surfaces in CDX-U
International Nuclear Information System (INIS)
Kaita, R.; Majeski, R.; Boaz, M.; Efthimion, P.; Jones, B.; Hoffman, D.; Kugel, H.; Menard, J.; Munsat, T.; Post-Zwicker, A.; Soukhanovskii, V.; Spaleta, J.; Taylor, G.; Timberlake, J.; Woolley, R.; Zakharov, L.; Finkenthal, M.; Stutman, D.; Antar, G.; Doerner, R.; Luckhardt, S.; Maingi, R.; Maiorano, M.; Smith, S.
2002-01-01
The Current Drive Experiment-Upgrade (CDX-U) device at the Princeton Plasma Physics Laboratory (PPPL) is a spherical torus (ST) dedicated to the exploration of liquid lithium as a potential solution to reactor first-wall problems such as heat load and erosion, neutron damage and activation, and tritium inventory and breeding. Initial lithium limiter experiments were conducted with a toroidally-local liquid lithium rail limiter (L3) from the University of California at San Diego. Spectroscopic measurements showed a clear reduction of impurities in plasmas with the L3, compared to discharges with a boron carbide limiter. The evidence for a reduction in recycling was less apparent, however. This may be attributable to the relatively small area in contact with the plasma, and the presence of high-recycling surfaces elsewhere in the vacuum chamber. This conclusion was tested in subsequent experiments with a fully toroidal lithium limiter that was installed above the floor of the vacuum vessel. The new limiter covered over ten times the area of the L3 facing the plasma. Experiments with the toroidal lithium limiter have recently begun. This paper describes the conditioning required to prepare the lithium surface for plasma operations, and effect of the toroidal liquid lithium limiter on discharge performance
Spherical Torus Plasma Interactions with Large-area Liquid Lithium Surfaces in CDX-U
Energy Technology Data Exchange (ETDEWEB)
R. Kaita; R. Majeski; M. Boaz; P. Efthimion; B. Jones; D. Hoffman; H. Kugel; J. Menard; T. Munsat; A. Post-Zwicker; V. Soukhanovskii; J. Spaleta; G. Taylor; J. Timberlake; R. Woolley; L. Zakharov; M. Finkenthal; D. Stutman; G. Antar; R. Doerner; S. Luckhardt; R. Maingi; M. Maiorano; S. Smith
2002-01-18
The Current Drive Experiment-Upgrade (CDX-U) device at the Princeton Plasma Physics Laboratory (PPPL) is a spherical torus (ST) dedicated to the exploration of liquid lithium as a potential solution to reactor first-wall problems such as heat load and erosion, neutron damage and activation, and tritium inventory and breeding. Initial lithium limiter experiments were conducted with a toroidally-local liquid lithium rail limiter (L3) from the University of California at San Diego. Spectroscopic measurements showed a clear reduction of impurities in plasmas with the L3, compared to discharges with a boron carbide limiter. The evidence for a reduction in recycling was less apparent, however. This may be attributable to the relatively small area in contact with the plasma, and the presence of high-recycling surfaces elsewhere in the vacuum chamber. This conclusion was tested in subsequent experiments with a fully toroidal lithium limiter that was installed above the floor of the vacuum vessel. The new limiter covered over ten times the area of the L3 facing the plasma. Experiments with the toroidal lithium limiter have recently begun. This paper describes the conditioning required to prepare the lithium surface for plasma operations, and effect of the toroidal liquid lithium limiter on discharge performance.
Recent results from the PLT tokamak
International Nuclear Information System (INIS)
Arunasalam, V.; Barnes, C.; Bol, K.
The results of the second operating period of PLT are reported. The main plasma parameters obtained with various discharge types are summarized and the importance of radiation in the energy balance is pointed out. Low temperature discharge cleaning allows the reduction of the amount of oxygen - the primary low-Z impurity. With this reduction the highest electron density and confinement time achieved are n=10 14 cm -3 and tsub(E)=70ms. Gas injection programming is used to reduce the effective ion charge, otherwise large amounts of tungsten cause such an increase in radiation from the plasma core that even a collapse of electron temperature occurs. It appears likely that edge cooling of the plasma is the mechanism that inhibits the influx of tungsten and makes possible the development of discharges with 70 ms confinement times. (J.U.)
Tennant, Allyn F.
1991-01-01
PLT is a high level plotting package. A Programmer can create a default plot suited for the data being displayed. At run times, users can then interact with the plot overriding any or all of these defaults. The user is also provided the capability to fit functions to the displayed data. This ability to display, interact with, and to fit the data make PLT a useful tool in the analysis of data. The Quick and Dandy Plotter (QDP) program will read ASCII text files that contain PLT commands and data. Thus, QDP provides and easy way to use the PLT software QPD files provide a convenient way to exchange data. The QPD/PLT software is written in standard FORTRAN 77 and has been ported to VAX VMS, SUN UNIX, IBM AIX, NeXT NextStep, and MS-DOS systems.
International Nuclear Information System (INIS)
Hosea, J.; Bernabei, S.; Colestock, P.
1979-07-01
Strong minority proton heating is produced in PLT through ion cyclotron resonance damping of fast waves at moderate rf power levels. In addition to demonstrating good proton confinement, the proton energy distribution is consistent with Fokker--Planck theory which provides the prescription for extrapolation of this heating regime to higher rf power levels
Torus knots and mirror symmetry
Brini, Andrea; Marino, Marcos
2012-01-01
We propose a spectral curve describing torus knots and links in the B-model. In particular, the application of the topological recursion to this curve generates all their colored HOMFLY invariants. The curve is obtained by exploiting the full Sl(2, Z) symmetry of the spectral curve of the resolved conifold, and should be regarded as the mirror of the topological D-brane associated to torus knots in the large N Gopakumar-Vafa duality. Moreover, we derive the curve as the large N limit of the matrix model computing torus knot invariants.
Effects of Large Area Liquid Lithium Limiters on Spherical Torus Plasmas
International Nuclear Information System (INIS)
Kaita, R.; Majeski, R.; Boaz, M.; Efthimion, P.; Gettelfinger, G.; Gray, T.; Hoffman, D.; Jardin, S.; Kugel, H.; Marfuta, P.; Munsat, T.; Neumeyer, C.; Raftopoulos, S.; Soukhanovskii, V.; Spaleta, J.; Taylor, G.; Timberlake, J.; Woolley, R.; Zakharov, L.; Finkenthal, M.; Stutman, D.; Delgado-Aparicio, L.; Seraydarian, R.P.; Antar, G.; Doerner, R.; Luckhardt, S.; Baldwin, M.; Conn, R.W.; Maingi, R.; Menon, M.; Causey, R.; Buchenauer, D.; Ulrickson, M.; Jones, B.; Rodgers, D.
2004-01-01
Use of a large-area liquid lithium surface as a first wall has significantly improved the plasma performance in the Current Drive Experiment-Upgrade (CDX-U) at the Princeton Plasma Physics Laboratory. Previous CDX-U experiments with a partially-covered toroidal lithium limiter tray have shown a decrease in impurities and the recycling of hydrogenic species. Improvements in loading techniques have permitted nearly full coverage of the tray surface with liquid lithium. Under these conditions, there was a large drop in the loop voltage needed to sustain the plasma current. The data are consistent with simulations that indicate more stable plasmas having broader current profiles, higher temperatures, and lowered impurities with liquid lithium walls. As further evidence for reduced recycling with a liquid lithium limiter, the gas puffing had to be increased by up to a factor of eight for the same plasma density achieved with an empty toroidal tray limiter
Effects of large area liquid lithium limiters on spherical torus plasmas
International Nuclear Information System (INIS)
Kaita, R.; Majeski, R.; Boaz, M.; Efthimion, P.; Gettelfinger, G.; Gray, T.; Hoffman, D.; Jardin, S.; Kugel, H.; Marfuta, P.; Munsat, T.; Neumeyer, C.; Raftopoulos, S.; Soukhanovskii, V.; Spaleta, J.; Taylor, G.; Timberlake, J.; Woolley, R.; Zakharov, L.; Finkenthal, M.; Stutman, D.; Delgado-Aparicio, L.; Seraydarian, R.P.; Antar, G.; Doerner, R.; Luckhardt, S.; Baldwin, M.; Conn, R.W.; Maingi, R.; Menon, M.; Causey, R.; Buchenauer, D.; Ulrickson, M.; Jones, B.; Rodgers, D.
2005-01-01
Use of a large-area liquid lithium surface as a limiter has significantly improved the plasma performance in the Current Drive Experiment-Upgrade (CDX-U) at the Princeton Plasma Physics Laboratory. Previous CDX-U experiments with a partially-covered toroidal lithium limiter tray have shown a decrease in impurities and the recycling of hydrogenic species. Improvements in loading techniques have permitted nearly full coverage of the tray surface with liquid lithium. Under these conditions, there was a large drop in the loop voltage needed to sustain the plasma current. The data are consistent with simulations that indicate more stable plasmas having broader current profiles, higher temperatures, and lowered impurities with liquid lithium walls. As further evidence for reduced recycling with a liquid lithium limiter, the gas puffing had to be increased by up to a factor of eight for the same plasma density achieved with an empty toroidal tray limiter
Demonstration of direct energy recovery of full-energy ions at 40 keV on a PLT/ISX beam system
International Nuclear Information System (INIS)
Stirling, W.L.; Barber, G.C.; Dagenhart, W.K.
1981-01-01
Neutral beam injection systems that employ positive ion sources presently operate at energies of about 40 to 50 keV/nucleon at 60 A [Princeton Large Torus (PLT)] or 100 A [Princeton Divertor Experiment (PDX) or the Oak Ridge National Laboratory (ORNL) Impurities Study Experiment (ISX)] with about 60% conversion efficiency. However, the desire for multisecond beams in the 80-keV/nucleon energy range at approx. 10 MW/module has emphasized the need for technological advances in several areas. At such beam energies, as much as 75% of the initial beam energy is retained in the unneutralized ion components. As a result, two questions immediately come to mind: (1) how can one dispose of this energy; or better still, (2) how can one efficiently recover this energy. We have proposed and demonstrated a unique solution to this problem that not only removes the need for beam dumps but also returns from 50 to 80% of the energy contained in the full energy ion component directly and dynamically to the high voltage supply. In fact, the energy in the residual ion component is not expended. The tests were made on a PLT/ISX-type beam line at 40 keV/nucleon with about 800 kW and 0.1 s
Pulsed power liner for PLT energy systems
International Nuclear Information System (INIS)
Armellino, C.A.; Bronner, G.; Murray, J.G.
1975-01-01
PLT is Princeton University's latest Tokamak machine in the controlled thermonuclear fusion research effort. The OH (ohmic heating) and SF (shaping field) systems for the machine place a very high energy pulsed current load on the AC line feeding them. This paper describes the two systems and the steps taken to insure minimum effect on line regulation during the pulsed operation
PLT and PDX perpendicular charge-exchange analyzers
International Nuclear Information System (INIS)
Mueller, D.; Hammett, G.W.; McCune, D.C.
1986-01-01
The perpendicular charge-exchange systems used on the poloidal divertor experiment and the Princeton large torus are comprised of ten-channel, mass-resolved, charge-exchange analyzers. Results from these systems indicate that instrumental effects can lead to erroneous temperature measurements during deuterium neutral beam injection or at low hydrogen concentrations
PLT neutral injection ignitron accelerating supply
International Nuclear Information System (INIS)
Ashcroft, D.L.; Murray, J.G.; Newman, R.A.; Peterson, F.L.
1975-11-01
A phase-controlled rectifier was designed for the accelerating supply on the PLT Neutral Beam Injection system at PPPL. The rectifier must furnish 70 amperes at up to 50 KV for 300 milliseconds, with a duty cycle of up to 10 percent. Protection of the injectors requires the supply to withstand repeated crowbarring. The rectifying element selected to satisfy these requirements was a commercially-available ignitron, installed in a supporting frame and using firing circuits and controls designed by PPPL
Electron cyclotron emission from the PLT tokamak
International Nuclear Information System (INIS)
Hosea, J.; Arunasalam, V.; Cano, R.
1977-07-01
Experimental measurements of electron cyclotron emission from the PLT tokamak plasma reveal that black-body emission occurs at the fundamental frequency. Such emission, not possible by direct thermal excitation of electromagnetic waves, is herein attributed to thermal excitation of electrostatic (Bernstein) waves which then mode convert into electromagnetic waves. The local feature of the electrostatic wave generation permits spatially and time resolved measurements of electron temperature as for the second harmonic emission
PLT neutral injection ignitron accelerating supply
International Nuclear Information System (INIS)
Ashcroft, D.L.; Murray, J.G.; Newman, R.A.; Peterson, F.L.
1976-03-01
A phase-controlled rectifier has been designed for the accelerating supply on the PLT Neutral Beam Injection system at PPPL. The rectifier must furnish 70 amperes at up to 50 KV for 300 milliseconds, with a duty cycle of up to 10 percent. Protection of the injectors requires the supply to withstand repeated crowbarring. The rectifying element selected to satisfy these requirements was a commercially-available ignitron, installed in a supporting frame and using firing circuits and controls designed by PPPL
Neutral beam injection on the PLT tokamak
International Nuclear Information System (INIS)
Schilling, G.; Ashcroft, D.L.; Eubank, H.P.; Grisham, L.R.; Knauer, R.C.; Stewart, L.D.; Stooksberry, R.W.; Ulrickson, M.; Williams, M.D.
1981-01-01
We describe the operation of the neutral beam injection system on the PLT tokamak. Improvements, retrofits, and conditioning have changed the injection system from an experiment in itself to a fairly reliable and useful plasma heating tool. We will present a brief overview of our physics achievements and then describe the system as it exists now. This will include injector performance, conditioning needs, maintenance needs, reliability, and daily operating sequences. We will also include hardware modifications and additions, electrical and mechanical, and point out remaining problem areas
International Nuclear Information System (INIS)
Hinnov, E.; Suckewer, S.; Bol, K.; Hawryluk, R.; Hosea, J.; Meservey, E.
1977-11-01
Low-Z impurities concentrations (oxygen and carbon) have been measured in different discharges in PLT. The contribution to Z/sub eff/, influx rates and radiation losses by oxygen and carbon were obtained. An inverse correlation was found between the low-Z impurity density (and also the edge ion temperature) and the high-Z impurity (tungsten) density. A one-dimensional computer transport model has been used to calculate the spatial profiles of different oxygen and carbon ionization states. This model predicts that fully stripped oxygen and carbon ions should exist near the plasma periphery
Test facility for PLT TF coils
International Nuclear Information System (INIS)
Hearney, J.; File, J.; Dreskin, S.
1975-01-01
Past experience with the model C stellerator and other toroidal field devices indicates that mechanical and electrical tests of a toroidal field coil prior to maximum field operation of the device is prudent and desirable. This paper describes a test program for the PLT-TF coils. The test stand consists of one test coil, two background coils and a steel supporting structure. The three coil configuration produces a 67.5 kG field at the inner conductor (38 kG at the bore center) and simulates a 1/R field distribution in the bore of the test coil. The resolution of the field force system and resultant stresses within the test structure are discussed. A test procedure is described which maximizes the information obtained from a 100,000 pulse program
Center column design of the PLT
International Nuclear Information System (INIS)
Citrolo, J.; Frankenberg, J.
1975-01-01
The center column of the PLT machine is a secondary support member for the toroidal field coils. Its purpose is to decrease the bending moment at the nose of the coils. The center column design was to have been a stainless steel casting with the toroidal field coils grouped around the casting at installation, trapping it in place. However, the castings developed cracks during fabrication and were unsuitable for use. Installation of the coils proceeded without the center column. It then became necessary to redesign a center column which would be capable of installation with the toroidal field coils in place. The final design consists of three A-286 forgings. This paper discusses the final center column design and the influence that new knowledge, obtained during the power tests, had on the new design
ORIGINAL ARTICLE Torus Palatinus and Torus Mandibularis in a ...
African Journals Online (AJOL)
Ogunbodede
; 28:105-111. 4. Seah, Y. H. Torus Palatinus and. Torus Mandibularis: a Review of the Literature. Aust. Dent. J. 1995;. 40:318-321. 5. Bernal, B. A.; Moreira, D. E.;. Rodriguez, P., I [Prevalence of. Torus Palatinus and Torus. Mandibularis in the ...
Long-term changes in the surface conditions of PLT
International Nuclear Information System (INIS)
Cohen, S.A.; Dylla, H.F.; Rossnagel, S.M.; Picraux, S.T.; Borders, J.A.; Magee, C.W.
1977-01-01
Long-term changes in the surface conditions of the PLT vacuum vessel wall have been monitored by the periodic analysis of a variety of sample substrates (stainless steel, alumina, silicon), exposed to PLT discharges for periods of up to several months and subsequently removed for analysis by Auger electron spectroscopy (AES), photoelectron spectroscopy, ion backscattering, nuclear reaction analysis, secondary ion mass spectroscopy, and scanning electron microscopy
Torus type thermonuclear device
International Nuclear Information System (INIS)
Imura, Yasuya.
1979-01-01
Purpose: To attain supporting effect against electromagnetic force and moderate the inner stress applied to toroidal coils due to thermal expansion by intervening a stress relaxation member between the outer circumferential side of a torus and a support device in toroidal coils. Constitution: Toroidal coils for confining a plasma within a torus vacuum container is supported on a support secured to upper and lower bases. A thermoplastic stress relaxation material of a low young's modulus is put between the outer circumferential side of the torus container and the torus outer circumferential side of the support in the toroidal coil. Thermoplastic resin is best suited to the stress relaxation substance, although tetrafluoro resin may be used as the stress relaxation substance while packing non-woven tetron fabric or non-woven glass fabric impregnated with varnish in a gap between the stress relaxation substance and the support or the toroidal coils. (Seki, T.)
Energy Technology Data Exchange (ETDEWEB)
Cobble, James Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
2016-06-09
This document summarizes the Bumpy Torus Experiment as a viable fusion reactor concept. Conclusions reached include the following: In 30 years, order-of-magnitude technological advances have occurred in multiple areas of plasma heating and confinement. The ORNL bumpy torus of the 1970s was technology limited. Now that ITER is technology limited, an alternate concept is needed. A device built on such a concept should be current free, CW, modular, have a gentle shutdown, and demonstrable stability. The bumpy torus meets or has the potential to meet all of these criteria. Earlier, stability was not possible due to power limits; it has not been fully tested. It is time to revisit the bumpy-torus concept with a modest new machine.
International Nuclear Information System (INIS)
Cobble, James Allen
2016-01-01
This document summarizes the Bumpy Torus Experiment as a viable fusion reactor concept. Conclusions reached include the following: In 30 years, order-of-magnitude technological advances have occurred in multiple areas of plasma heating and confinement. The ORNL bumpy torus of the 1970s was technology limited. Now that ITER is technology limited, an alternate concept is needed. A device built on such a concept should be current free, CW, modular, have a gentle shutdown, and demonstrable stability. The bumpy torus meets or has the potential to meet all of these criteria. Earlier, stability was not possible due to power limits; it has not been fully tested. It is time to revisit the bumpy-torus concept with a modest new machine.
Studying uniform thickness II: Transversely nonsimple iterated torus knots
DEFF Research Database (Denmark)
LaFountain, Douglas
2011-01-01
We prove that an iterated torus knot type in the standard contact 3-sphere fails the uniform thickness property (UTP) if and only if it is formed from repeated positive cablings, which is precisely when an iterated torus knot supports the standard contact structure. This is the first complete UTP...... classification for a large class of knots. We also show that all iterated torus knots that fail the UTP support cabling knot types that are transversely non-simple....
International Nuclear Information System (INIS)
Linford, R.K.; Armstrong, W.T.; Bartsch, R.R.
1981-01-01
The Compact Torus (CT) concept includes any axisymmetric toroidal plasma configuration, which does not require the linking of any material through the hole in the torus. Thus, the magnet coils, vacuum vessel, etc., have a simple cylindrical or spherical geometry instead of the toroidal geometry required for Tokamaks and RFP's. This simplified geometry results in substantial engineering advantages in CT reactor embodiments while retaining the good confinement properties afforded by an axisymmetric toroidal plasma-field geometry. CT's can be classified into three major types by using the ion gyro radius rho/sub i/ and the magnitude of the maximum toroidal field B/sub tm/
Dissipative trapped ion instability in PLT and INTOR
International Nuclear Information System (INIS)
Wakamatsu, A.; Shimizu, K.; Ogasawara, M.
1983-06-01
The generation conditions of the dissipative trapped ion instability (DTII) are investigated for the parameters of PLT and INTOR. The finite banana width effect is taken into account in the dispersion relation. The conditions are greatly influenced by the impurities. Though the plasmas are well in the banana regime in bothe PLT and INTOR, DTII is not excited for Zsub(eff) = 3.5, and excited but it has negative growth rate for Zsub(eff) = 1.5, where Zsub(eff) is the effective charge number. Only for the pure case (Zsub(eff) = 1.0), the growth rate has small positive value in INTOR. (author)
Principal noncommutative torus bundles
DEFF Research Database (Denmark)
Echterhoff, Siegfried; Nest, Ryszard; Oyono-Oyono, Herve
2008-01-01
of bivariant K-theory (denoted RKK-theory) due to Kasparov. Using earlier results of Echterhoff and Williams, we shall give a complete classification of principal non-commutative torus bundles up to equivariant Morita equivalence. We then study these bundles as topological fibrations (forgetting the group...
International Nuclear Information System (INIS)
Grisham, D.L.
1981-01-01
A remote handling system is proposed for moving a torus sector of the accelerator from under the cryostat to a point where it can be handled by a crane and for the reverse process for a new sector. Equipment recommendations are presented, as well as possible alignment schemes. Some general comments about future remote-handling methods and the present capabilities of existing systems will also be included. The specific task to be addressed is the removal and replacement of a 425 to 450 ton torus sector. This requires a horizontal movement of approx. 10 m from a normal operating position to a point where its further transport can be accomplished by more conventional means (crane or floor transporter). The same horizontal movement is required for reinstallation, but a positional tolerance of 2 cm is required to allow reasonable fit-up for the vacuum seal from the radial frames to the torus sector. Since the sectors are not only heavy but rather tall and narrow, the transport system must provide a safe, stable, and repeatable method fo sector movement. This limited study indicates that the LAMPF-based method of transporting torus sectors offers a proven method of moving heavy items. In addition, the present state of the art in remote equipment is adequate for FED maintenance
Various semiclassical limits of torus conformal blocks
Energy Technology Data Exchange (ETDEWEB)
Alkalaev, Konstantin [I.E. Tamm Department of Theoretical Physics, P.N. Lebedev Physical Institute,Leninsky ave. 53, Moscow, 119991 (Russian Federation); Department of General and Applied Physics, Moscow Institute of Physics and Technology,Institutskiy per. 7, Dolgoprudnyi, Moscow region, 141700 (Russian Federation); Geiko, Roman [Mathematics Department, National Research University Higher School of Economics,Usacheva str. 6, Moscow, 119048 (Russian Federation); Rappoport, Vladimir [I.E. Tamm Department of Theoretical Physics, P.N. Lebedev Physical Institute,Leninsky ave. 53, Moscow, 119991 (Russian Federation); Department of Quantum Physics, Institute for Information Transmission Problems,Bolshoy Karetny per. 19, Moscow, 127994 (Russian Federation)
2017-04-12
We study four types of one-point torus blocks arising in the large central charge regime. There are the global block, the light block, the heavy-light block, and the linearized classical block, according to different regimes of conformal dimensions. It is shown that the blocks are not independent being connected to each other by various links. We find that the global, light, and heavy-light blocks correspond to three different contractions of the Virasoro algebra. Also, we formulate the c-recursive representation of the one-point torus blocks which is relevant in the semiclassical approximation.
Torus type thermonuclear device
International Nuclear Information System (INIS)
Gomei, Yoshio.
1982-01-01
Purpose: To facilitate heat removal at limiters and enable helium discharge without using a diverter by the separate disposition of a main limiter receiving the heat from plasmas and an auxiliary limiter for helium discharge. Constitution: A main limiter for establishing and maintaining torus plasmas and an auxiliary limiter for helium discharge are disposed separately. The auxiliary limiter is disposed between the magnetic plane at the position where the plasmas in the confining region begin to contact the main limiter and the first blanket wall. Thus, a sufficient contact area with the plasmas can be taken for the main limiter disposed to the inside of the torus to thereby avoid excess heat concentration. Further, helium ions transported through a passage along the magnetic plane between the main limiter and the first blanket wall to the exhaust chamber are neutralized and thereafter discharged by the auxiliary limiter. (Moriyama, K.)
Torus Breakdown in Noninvertible Maps
DEFF Research Database (Denmark)
Maistrenko, V.; Maistrenko, Yu.; Mosekilde, Erik
2003-01-01
We propose a criterion for the destruction of a two-dimensional torus through the formation of an infinite set of cusp points on the closed invariant curves defining the resonance torus. This mechanism is specific to noninvertible maps. The cusp points arise when the tangent to the torus at the p......We propose a criterion for the destruction of a two-dimensional torus through the formation of an infinite set of cusp points on the closed invariant curves defining the resonance torus. This mechanism is specific to noninvertible maps. The cusp points arise when the tangent to the torus...... at the point of intersection with the critical curve L-0 coincides with the eigendirection corresponding to vanishing eigenvalue for the noninvertible map. Further parameter changes lead typically to the generation of loops (self-intersections of the invariant manifolds) followed by the transformation...
Induction effects of torus knots and unknots
Oberti, Chiara; Ricca, Renzo L.
2017-09-01
Geometric and topological aspects associated with induction effects of field lines in the shape of torus knots/unknots are examined and discussed in detail. Knots are assumed to lie on a mathematical torus of circular cross-section and are parametrized by standard equations. The induced field is computed by direct integration of the Biot-Savart law. Field line patterns of the induced field are obtained and several properties are examined for a large family of knots/unknots up to 51 crossings. The intensity of the induced field at the origin of the reference system (center of the torus) is found to depend linearly on the number of toroidal coils and reaches maximum values near the boundary of the mathematical torus. New analytical estimates and bounds on energy and helicity are established in terms of winding number and minimum crossing number. These results find useful applications in several contexts when the source field is either vorticity, electric current or magnetic field, from vortex dynamics to astrophysics and plasma physics, where highly braided magnetic fields and currents are present.
Confinement studies during neutral beam injection in PLT
International Nuclear Information System (INIS)
Goldston, R.; Davis, S.; Eubank, H.
1980-12-01
Neutral beam injection experiments on PLT have provided definitive information on ion energy confinement in highly collisionless plasmas. We find that ion thermal conduction is consistent, within a factor of approx. 3, with neoclassical theory, and that anomalous thermal convection of ion energy is a factor of 2-3 less than would be calculated from the INTOR D/sub e/ with a convection loss term of the form 5/2nkTv/sub r/. From our experiments with a shunted TF coil we have found that a single shallow ripple well of 2.5% has a neglible effect on ion energy confinement, even at the lowest collisionality obtainable on PLT. Scrutiny of the analytic theories of ripple induced transport motivated by these experiments, suggests that more theoretical (and perhaps numerical) work is needed in this area
Soft x-ray measurements on the PLT Tokamak
International Nuclear Information System (INIS)
Von Goeler, S.; Sauthoff, N.; Bitter, M.
1977-10-01
Four experiments are described that currently run on the PLT tokamak and which utilize the soft x-ray emission of the plasma as a diagnostic: the pulse height analysis system for temperature and impurity measurements; the curved crystal Bragg spectrometer for the determination of ionization states of impurities; ''windowless'' surface barrier detectors for the investigation of the ultra soft x-ray radiation in the energy range 0.1 keV < hν < 1 keV and a silicon diode array for x-ray fluctuation measurements. For each diagnostic a short technical description and some recent results obtained with it on PLT are given in order to demonstrate its use
Compact torus compression of microwaves
International Nuclear Information System (INIS)
Hewett, D.W.; Langdon, A.B.
1985-01-01
The possibility that a compact torus (CT) might be accelerated to large velocities has been suggested by Hartman and Hammer. If this is feasible one application of these moving CTs might be to compress microwaves. The proposed mechanism is that a coaxial vacuum region in front of a CT is prefilled with a number of normal electromagnetic modes on which the CT impinges. A crucial assumption of this proposal is that the CT excludes the microwaves and therefore compresses them. Should the microwaves penetrate the CT, compression efficiency is diminished and significant CT heating results. MFE applications in the same parameters regime have found electromagnetic radiation capable of penetrating, heating, and driving currents. We report here a cursory investigation of rf penetration using a 1-D version of a direct implicit PIC code
International Nuclear Information System (INIS)
Berry, L.A.; Hedrick, C.L.; Uckan, N.A.
1979-03-01
The ELMO Bumpy Torus (EBT) program of experiment, theory, and reactor studies has been a remarkably successful one. In the five years since EBT-I began operating, work has progressed from a demonstration of macrostability to an increasingly detailed understanding of transport properties. Collisionless scaling (tau/sub E/ increases with temperature) has been observed, and the magnitude of the energy confinement time is consistent with neoclassical theory. Experiments on EBT-S (for scale) are now being conducted at the increased magnetic field levels and higher microwave power and frequency made possible by a 28-GHz gyrotron development program. A review of the program is given
International Nuclear Information System (INIS)
McAlees, D.G.; Uckan, N.A.; Lidsky, L.M.
1976-01-01
In the Elmo Bumpy Torus Reactor (EBTR) study the feasibility of achieving a fusion power plant based on the EBT confinement concept was evaluated. If the present understanding of the physics can be extrapolated to reactor scale devices the reactor could operate at high beta, high power density, and at steady state. The high aspect ratio of the device eases the accessibility, structural design and remote maintenance problems which are common to low aspect ratio machines. A version of the EBTR reference design described here could be constructed with only minor extrapolations in available technology
Spherical Torus Center Stack Design
International Nuclear Information System (INIS)
C. Neumeyer; P. Heitzenroeder; C. Kessel; M. Ono; M. Peng; J. Schmidt; R. Woolley; I. Zatz
2002-01-01
The low aspect ratio spherical torus (ST) configuration requires that the center stack design be optimized within a limited available space, using materials within their established allowables. This paper presents center stack design methods developed by the National Spherical Torus Experiment (NSTX) Project Team during the initial design of NSTX, and more recently for studies of a possible next-step ST (NSST) device
New cryogenic temperature monitor: PLT-HPT-32
Viera Curbelo, Teodora Aleida; Martín-Fernández, Sergio Gonzáles; Hoyland, R.; Vega-Moreno, A.; Cozar Castellano, Juan; Gómez Reñasco, M. F.; Aguiar-González, M.; Pérez de Taoro, Angeles; Sánchez-de la Rosa, V.; Rubiño-Martín, J. A.; Génova-Santos, R.
2016-07-01
The PLT-HPT-32, a new cryogenic temperature monitor, has been developed by the Institute of Astrophysics of the Canary Islands (IAC) and an external engineering company (Sergio González Martín-Fernandez). The PLT-HPT-32 temperature monitor offers precision measurement in a wide range of cryogenic and higher-temperature applications with the ability to easily monitor up to 32 sensor channels. It provides better measurement performance in applications where researchers need to ensure accuracy and precision in their low cryogenic temperature monitoring. The PLT-HPT-32 supports PTC RTDs such as platinum sensors, and diodes such as the Lake Shore DT-670 Series. Used with silicon diodes, it provides accurate measurements in cryo-cooler applications from 16 K to above room temperature. The resolution of the measurement is less than 0.1K. Measurements can be displayed in voltage units or Kelvin units. For it, two different tables can be used. One can be programmed by the user, and the other one corresponds to Lake Shore DT670 sensor that comes standard. There are two modes of measuring, the instantaneous mode and averaged mode. In this moment, all channels must work in the same mode but in the near future it expected to be used in blocks of eight channels. The instantaneous mode takes three seconds to read all channels. The averaged mode takes one minute to average twenty samples in all channels. Alarm thresholds can be configured independently for each input. The alarm events, come from the first eight channels, can activate the unit's relay outputs for hard-wired triggering of other systems or audible annunciators. Activate relays on high, low, or both alarms for any input. For local monitoring, "Stand-Alone Mode", the front panel of the PLT-HPT-32 features a bright liquid crystal display with an LED backlight that shows up to 32 readings simultaneously. Plus, monitoring can be done over a network "Remote Control Mode". Using the Ethernet port on the PLT-HPT-32, you
International Nuclear Information System (INIS)
Sperling, J.L.; Hamasaki, S.; Krall, N.A.
1982-01-01
In order that a stable bumpy torus plasma configuration can be attained, it is first necessary to irradiate the plasma with sufficient external power to cause annulus formation. To estimate the power required to initiate annuli, it is assumed that quasilinear electron-cyclotron heating by microwaves is the dominant electron heating mechanism. A scaling law for required microwave power is derived which shows that annulus formation is assisted by smaller cross-section areas, lower density, lower microwave frequency, and higher C-mode temperature. The scaling law is quantitatively evaluated for NBT, EBT-1, EBT-S, EBT-P, and EBT-R parameters. The resulting power estimates are consistent with the available microwave power in previous and present experiments. In larger projected bumpy tori, like EBT-P and EBT-R, it may be necessary to initiate annulus formation at densities which are lower than in the stable T-mode so that the necessary microwave power can be reduced to reasonably modest levels. It is suggested that instabilities as well as rf heating can aid the formation of bumpy torus electron annuli. Rf experiments on NBT and EBT-S would be beneficial in determining the capability of rf power to assist annulus startup
Second harmonic ion cylotron resonance heating by the fast magnetosonic wave on the PLT tokamak
International Nuclear Information System (INIS)
Thompson, H.R. Jr.
1984-01-01
Second harmonic ion cyclotron resonance heating by the fast magnetosonic wave, and the propagation of the fast wave from the fundamental of the ion cyclotron frequency to its second harmonic was investigated in a hydrogen plasma on the PLT tokamak. The theory of fast magnetosonic wave propagation was extended to include the effects of density gradients, plasma current, and impurity ion species. The damping of the fast wave at the second harmonic is calculated, where the theory has been extended to include the full radial dependence of the fast wave fields. Power deposition profiles and eigenmode Q's are calculated using this theory. The effects of the interaction between the ion Bernstein wave and the fast magnetosonic wave are calculated, and enhanced fast wave damping is predicted. The antenna loading is calculated including the effects of overlap of the fast wave eigenmodes. During the second harmonic heating experiments, the antenna loading was characterized as a function of the plasma parameters, and efficient coupling of the RF power to the plasma at high density was observed. At very low densities, fast wave eigenmodes were identified on PLT, and their Q's are measured. Eigenmodes with different toroidal directions of propagation were observed to exhibit large splitting in density due to the plasma current. Efficient bulk heating, with centrally peaked profiles, is observed at the second harmonic, and a tail, which decreases monotonically with energy, is observed on the ion distribution
The incredible shrinking torus
International Nuclear Information System (INIS)
Fischler, W.; Susskind, L.
1997-01-01
Using M(atrix) theory, the dualities of toroidally compactified M-theory can be formulated as properties of super Yang Mills theories in various dimensions. We consider the cases of compactification on 1-, 2-, 3-, 4- and 5-dimensional tori. The dualities required by string theory lead to conjectures of remarkable symmetries and relations between field theories as well as extremely unusual dynamical properties. By studying the theories in the limit of vanishingly small tori, a wealth of information is obtained about strongly coupled fixed points of super Yang-Mills theory in various dimensions. Perhaps the most striking behavior, as noted by Rozali in this context, is the emergence of an additional dimension of space in the case of a 4-torus. (orig.)
Torus type thermonuclear device
International Nuclear Information System (INIS)
Kitazawa, Hakaru; Saito, Ryusei.
1981-01-01
Purpose: To obtain toroidal coil supports structures capable of coping with the changes in the elasticity distribution due to thermal expansion and performing elastic support function corresponding to the distribution of stresses exerted on the toroidal coils, by providing elastic function to the inner circumference side of the coil support structures. Constitution: Support structures for supporting toroidal coils from above and below are formed at the torus inner circumference side thereof with ribs in contact with a central block and having elasticity coefficient corresponding to the distribution of stresses exerted on the toroidal coils, and the stresses exerted on the toroidal coils are elastically supported on the ribs. Accordingly, if the stress distribution varies due to the thermal expansion or the like, adequate supporting function can be obtained well-corresponding to such changes, whereby effective plasma confinement can be attained. (Moriyama, K.)
Exploring Torus Universes in Causal Dynamical Triangulations
DEFF Research Database (Denmark)
Budd, Timothy George; Loll, R.
2013-01-01
Motivated by the search for new observables in nonperturbative quantum gravity, we consider Causal Dynamical Triangulations (CDT) in 2+1 dimensions with the spatial topology of a torus. This system is of particular interest, because one can study not only the global scale factor, but also global...... shape variables in the presence of arbitrary quantum fluctuations of the geometry. Our initial investigation focusses on the dynamics of the scale factor and uncovers a qualitatively new behaviour, which leads us to investigate a novel type of boundary conditions for the path integral. Comparing large....... Apart from setting the stage for the analysis of shape dynamics on the torus, the new set-up highlights the role of nontrivial boundaries and topology....
TORUS Annual Continuation and Progress Report
Energy Technology Data Exchange (ETDEWEB)
Arbanas, Goran [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Elster, Charlotte [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Echer, Jutta [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Nunes, Filomena [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Thompson, Ian [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)
2014-02-24
The TORUS collaboration derives its name from the research it focuses on, namely the Theory of Reactions for Unstable iSotopes. It is a Topical Collaboration in Nuclear Theory, and funded by the Nuclear Theory Division of the Office of Nuclear Physics in the Office of Science of the Department of Energy. The funding supports one postdoctoral researcher for the years 1 through 4. The collaboration brings together as Principal Investigators a large fraction of the nuclear reaction theorists currently active within the USA. The mission of the TORUS Topical Collaboration is to develop new methods that will advance nuclear reaction theory for unstable isotopes by using three-body techniques to improve directreaction calculations. This multi-institution collaborative effort is directly relevant to three areas of interest: the properties of nuclei far from stability; microscopic studies of nuclear input parameters for astrophysics, and microscopic nuclear reaction theory.
Next Step Spherical Torus Design Studies
International Nuclear Information System (INIS)
Neumeyer, C.; Heitzenroeder, P.; Kessel, C.; Ono, M.; Peng, M.; Schmidt, J.; Woolley, R.; Zatz, I.
2002-01-01
Studies are underway to identify and characterize a design point for a Next Step Spherical Torus (NSST) experiment. This would be a ''Proof of Performance'' device which would follow and build upon the successes of the National Spherical Torus Experiment (NSTX) a ''Proof of Principle'' device which has operated at PPPL since 1999. With the Decontamination and Decommissioning (DandD) of the Tokamak Fusion Test Reactor (TFTR) nearly completed, the TFTR test cell and facility will soon be available for a device such as NSST. By utilizing the TFTR test cell, NSST can be constructed for a relatively low cost on a short time scale. In addition, while furthering spherical torus (ST) research, this device could achieve modest fusion power gain for short-pulse lengths, a significant step toward future large burning plasma devices now under discussion in the fusion community. The selected design point is Q=2 at HH=1.4, P subscript ''fusion''=60 MW, 5 second pulse, with R subscript ''0''=1.5 m, A=1.6, I subscript ''p''=10vMA, B subscript ''t''=2.6 T, CS flux=16 weber. Most of the research would be conducted in D-D, with a limited D-T campaign during the last years of the program
International Nuclear Information System (INIS)
2007-01-01
The successful development of ITER and DEMO scenarios requires preparatory activities on devices that are smaller than ITER, sufficiently flexible and capable of investigating the peculiar physics of burning plasma conditions. The aim of the Fusion Advanced Studies Torus (FAST) proposal [2.1] (formerly FT3 [2.2]) is to show that the preparation of ITER scenarios and the development of new expertise for the DEMO design and RD can be effectively implemented on a new facility. FAST will a) operate with deuterium plasmas, thereby avoiding problems associated with tritium, and allow investigation of nonlinear dynamics (which are important for understanding alpha particle behaviour in burning plasmas) by using fast ions accelerated by heating and current drive systems; b) work in a dimensionless parameter range close to that of ITER; c) test technical innovative solutions, such as full-tungsten plasma-facing components and an advanced liquid metal divertor target for the first wall/divertor, directly relevant for ITER and DEMO; d) exploit advanced regimes with a much longer pulse duration than the current diffusion time; e) provide a test bed for ITER and DEMO diagnostics; f) provide an ideal framework for model and numerical code benchmarks, their verification and validation in ITER/ DEMO-relevant plasma conditions
International Nuclear Information System (INIS)
1978-01-01
The ELMO Bumpy Torus (EBT) program of experiment, theory, and reactor studies has been a remarkably successful one. In the five years since EBT-I began operating, work has progressed from demonstrating macrostability to an increasingly detailed understanding of transport properties. Collisionless scaling (tau/sub E/ increases with temperature) has been observed and the magnitude of the energy confinement time is consistent with neoclassical theory. Experiments on EBT-S are now being conducted at the increased magnetic field levels and higher microwave power and frequency made possible by a 28-GHz gyrotron development program. Initial results confirm our assumptions of neoclassical scaling. In conjunction with the experimental advances, EBT theory now has a well-developed transport theory which models the physics which we now think to be important: for example, it yields negative ambipolar electric fields which are consistent with those measured. Stability calculations continue to predict stable equilibrium with β/sub ring/ approx. β/sub core/ approx. 20 to 40%
International Nuclear Information System (INIS)
Mazzucato, E.; Fidone, I.; Cavallo, A.; von Goeler, S.; Hsuan, H.
1986-05-01
The absorption of 60 GHz electron cyclotron waves, with the extraordinary mode and an oblique angle of propagation, has been investigated in the PLT tokamak in the regime of down-shifted frequencies. The production of energetic electrons, with energies of up to 300 to 400 keV, peaks at values of toroidal field (approx. =29 kG) for which the wave frequency is significantly smaller than the electron cyclotron frequency in the whole plasma region. The observations are consistent with the predictions of the relativistic theory of electron cyclotron damping at down-shifted frequency. Existing rf sources make this process a viable method for assisting the current ramp-up, and for heating the plasma of present large tokamaks
Measurements of the PLT and PDX device activation
International Nuclear Information System (INIS)
Stavely, J.; Barnes, C.W.; Chrien, R.E.; Strachan, J.D.
1981-09-01
Measurements of the activation levels around the PLT and PDX tokamaks have been made using a Ge(Li) gamma spectrometer and a Geiger counter. The activation results from radiation induced in the plasma by 14 MeV neutrons from the d(t,n)α fusion reaction, 14.7 MeV protons from the d( 3 He,p)α fusion reaction, 10 → 20 MeV hard x-rays from runaway electron induced bremmstrahlung, and 2.5 MeV neutrons from the d(d,n) 3 He fusion reaction. The magnitude of the activation is compared to that predicted for PDX on the basis of one-dimensional activation codes
Electron heating using lower hybrid waves in the PLT tokamak
International Nuclear Information System (INIS)
Bell, R.E.; Bernabei, S.; Cavallo, A.; Chu, T.K.; Luce, T.; Motley, R.; Ono, M.; Stevens, J.; von Goeler, S.
1987-06-01
Lower hybrid waves with a narrow high velocity wave spectrum have been used to achieve high central electron temperatures in a tokamak plasma. Waves with a frequency of 2.45 GHz launched by a 16-waveguide grill at a power level less than 600 kW were used to increase the central electron temperature of the PLT plasma from 2.2 keV to 5 keV. The magnitude of the temperature increase depends strongly on the phase difference between the waveguides and on the direction of the launched wave. A reduction in the central electron thermal diffusivity is associated with the peaked electron temperature profiles of lower hybrid current-driven plasmas. 16 refs
Edge modelling of ICFR heated plasmas on PLT
International Nuclear Information System (INIS)
Lehrman, I.S.
1990-01-01
Theoretical models are presented to explain the edge plasma-antenna interaction that occurs during ICRF heating. The periodic structure of the Faraday shield is found to result in strong ponderomotive force in the vicinity of the antenna. A fluid model, which incorporates the ponderomotive force, predicts an increase in particle transport to the Faraday shield. Kinetic modelling shows that the strong antenna near-fields act to increase the energy of deuterons that strike the shield, thereby increasing the sputtering of shield material. In addition, kinetic modelling shows that E parallel induced between adjacent shield elements acts to heat edge electron that transit close to the antenna. The predictions of the models are shown to be consistent with measurements of enhanced transport on PLT. (author). 27 refs, 17 figs
Compact magnetic confinement fusion: Spherical torus and compact torus
Directory of Open Access Journals (Sweden)
Zhe Gao
2016-05-01
Full Text Available The spherical torus (ST and compact torus (CT are two kinds of alternative magnetic confinement fusion concepts with compact geometry. The ST is actually a sub-category of tokamak with a low aspect ratio; while the CT is a toroidal magnetic configuration with a simply-connected geometry including spheromak and field reversed pinch. The ST and CT have potential advantages for ultimate fusion reactor; while at present they can also provide unique fusion science and technology contributions for mainstream fusion research. However, some critical scientific and technology issues should be extensively investigated.
Bifurcation structure of successive torus doubling
International Nuclear Information System (INIS)
Sekikawa, Munehisa; Inaba, Naohiko; Yoshinaga, Tetsuya; Tsubouchi, Takashi
2006-01-01
The authors discuss the 'embryology' of successive torus doubling via the bifurcation theory, and assert that the coupled map of a logistic map and a circle map has a structure capable of generating infinite number of torus doublings
'Affine' algebras on the torus
International Nuclear Information System (INIS)
Zakkari, M.
1993-07-01
The analysis of the Kac-Moody ''like'' algebra L-circumflex 2 (G) on the torus is performed. It will be seen that the root systems construction leading to a Cartan matrix is not possible. Different twist of L-circumflex 2 λ (G) are discussed. Connections with known results are done. (author). 10 refs
National Spherical Torus Experiment (NSTX) Torus Design, Fabrication and Assembly
International Nuclear Information System (INIS)
Neumeyer, C.; Barnes, G.; Chrzanowski, J.H.; Heitzenroeder, P.
1999-01-01
The National Spherical Torus Experiment (NSTX) is a low aspect ratio spherical torus (ST) located at Princeton Plasma Physics Laboratory (PPPL). Fabrication, assembly, and initial power tests were completed in February of 1999. The majority of the design and construction efforts were constructed on the Torus system components. The Torus system includes the centerstack assembly, external Poloidal and Toroidal coil systems, vacuum vessel, torus support structure and plasma facing components (PFC's). NSTX's low aspect ratio required that the centerstack be made with the smallest radius possible. This, and the need to bake NSTXs carbon-carbon composite plasma facing components at 350 degrees C, was major drivers in the design of NSTX. The Centerstack Assembly consists of the inner legs of the Toroidal Field (TF) windings, the Ohmic Heating (OH) solenoid and its associated tension cylinder, three inner Poloidal Field (PF) coils, thermal insulation, diagnostics and an Inconel casing which forms the inner wall of the vacuum vessel boundary. It took approximately nine months to complete the assembly of the Centerstack. The tight radial clearances and the extreme length of the major components added complexity to the assembly of the Centerstack components. The vacuum vessel was constructed of 304-stainless steel and required approximately seven months to complete and deliver to the Test Cell. Several of the issues associated with the construction of the vacuum vessel were control of dimensional stability following welding and controlling the permeability of the welds. A great deal of time and effort was devoted to defining the correct weld process and material selection to meet our design requirements. The PFCs will be baked out at 350 degrees C while the vessel is maintained at 150 degrees C. This required care in designing the supports so they can accommodate the high electromagnetic loads resulting from plasma disruptions and the resulting relative thermal expansions
Arithmetic functions in torus and tree networks
Bhanot, Gyan; Blumrich, Matthias A.; Chen, Dong; Gara, Alan G.; Giampapa, Mark E.; Heidelberger, Philip; Steinmacher-Burow, Burkhard D.; Vranas, Pavlos M.
2007-12-25
Methods and systems for performing arithmetic functions. In accordance with a first aspect of the invention, methods and apparatus are provided, working in conjunction of software algorithms and hardware implementation of class network routing, to achieve a very significant reduction in the time required for global arithmetic operation on the torus. Therefore, it leads to greater scalability of applications running on large parallel machines. The invention involves three steps in improving the efficiency and accuracy of global operations: (1) Ensuring, when necessary, that all the nodes do the global operation on the data in the same order and so obtain a unique answer, independent of roundoff error; (2) Using the topology of the torus to minimize the number of hops and the bidirectional capabilities of the network to reduce the number of time steps in the data transfer operation to an absolute minimum; and (3) Using class function routing to reduce latency in the data transfer. With the method of this invention, every single element is injected into the network only once and it will be stored and forwarded without any further software overhead. In accordance with a second aspect of the invention, methods and systems are provided to efficiently implement global arithmetic operations on a network that supports the global combining operations. The latency of doing such global operations are greatly reduced by using these methods.
FLIT: Flowing LIquid metal Torus
Kolemen, Egemen; Majeski, Richard; Maingi, Rajesh; Hvasta, Michael
2017-10-01
The design and construction of FLIT, Flowing LIquid Torus, at PPPL is presented. FLIT focuses on a liquid metal divertor system suitable for implementation and testing in present-day fusion systems, such as NSTX-U. It is designed as a proof-of-concept fast-flowing liquid metal divertor that can handle heat flux of 10 MW/m2 without an additional cooling system. The 72 cm wide by 107 cm tall torus system consisting of 12 rectangular coils that give 1 Tesla magnetic field in the center and it can operate for greater than 10 seconds at this field. Initially, 30 gallons Galinstan (Ga-In-Sn) will be recirculated using 6 jxB pumps and flow velocities of up to 10 m/s will be achieved on the fully annular divertor plate. FLIT is designed as a flexible machine that will allow experimental testing of various liquid metal injection techniques, study of flow instabilities, and their control in order to prove the feasibility of liquid metal divertor concept for fusion reactors. FLIT: Flowing LIquid metal Torus. This work is supported by the US DOE Contract No. DE-AC02-09CH11466.
International Nuclear Information System (INIS)
Adam, J.; Aymar, R.; Briffod, G.
1979-10-01
Clearly a new device now ready for construction will be operated during roughly the same period of time as JET and it should therefore be designed as a useful complement to JET with the aim of preparing for the next phase of the programme. A number of prospective studies, in particular the Long Term Planning and the work on INTOR and NET have pointed out several fields where a large effort was needed. In some of these fields the EURATOM-C.E.A. Association is especially well prepared to bring important contributions and this is the case for: - the construction and operation of a super conducting Tokamak, - the development of Radio Frequency Heating. These two subjects have been chosen as the major items of the proposed programme. In addition the existing expertise in Tokamak physics and the characteristics of the device lead to propose two other subjects of work, namely: - the dynamics of impurities, - the study of long pulses
Linear pinch driven by a moving compact torus
International Nuclear Information System (INIS)
Hartman, C.W.; Hammer, J.H.; Eddleman, J.L.
1984-01-01
In principle, a Z-pinch of sufficiently large aspect ratio can provide arbitrarily high magnetic field intensity for the confinement of plasma. In practice, however, achievable field intensities and timescales are limited by parasitic inductances, pulse driver power, current, voltage, and voltage standoff of nearby insulating surfaces or surrounding gas. Further, instabilities may dominate to prevent high fields (kink mode) or enhance them (sausage mode) but in a nonuniform and uncontrollable way. In this paper we discuss an approach to producing a high-field-intensity pinch using a moving compact torus. The moving torus can serve as a very high power driver and may be used to compress a pre-established pinch field, switch on an accelerating pinch field, or may itself be reconfigured to form an intense pinch. In any case, the high energy, high energy density, and high velocity possible with an accelerated compact torus can provide extremely high power to overcome, by a number of orders of magnitude, the limitations to pinch formation described earlier. In this paper we will consider in detail pinches formed by reconfiguration of the compact torus
International Nuclear Information System (INIS)
Aizawa, N; Chakrabarti, R
2007-01-01
We note that the recently introduced fuzzy torus can be regarded as a q-deformed parafermion. Based on this picture, classification of the Hermitian representations of the fuzzy torus is carried out. The result involves Fock-type representations and new finite-dimensional representations for q being a root of unity as well as already known finite-dimensional ones
Effect of Poultry Litter Treatment (PLT) on death due to ascites in broilers.
Terzich, M; Quarles, C; Goodwin, M A; Brown, J
1998-01-01
The purposes of this study were to determine the effect of Poultry Litter Treatment (PLT) on levels of litter moisture, litter nitrogen, atmospheric ammonia, and death due to ascites. Data were collected from chicks raised in containment conditions that resembled commercial settings. The ascites death rate (5.9%) in broiler chicks on PLT-treated litter was significantly (chi 2 = 15.5, df = 1, P = 0.0001) lower than that (31.5%) in broiler chicks raised on untreated litter. Likewise, atmospheric ammonia levels in pens that had been treated with PLT were significantly (P litter moisture and litter nitrogen levels were not different (P > 0.05) among treatments at any sample interval.
Waveguide elliptic polarizers for ECH at down-shifted frequencies on PLT
International Nuclear Information System (INIS)
Doane, J.L.
1986-01-01
ECH experiments on PLT with resonance frequencies of 80 to 90 GHz at the plasma center use 60 GHz extraordinary mode (X-mode) propagation at 30 0 from the toroidal field. Efficient excitation of this mode requires elliptic polarization of the incident wave at the plasma edge. On PLT the elliptic polarization is achieved outside the vacuum vessel in an elliptically deformed section of circular waveguide propagating TM11, a mode that is intermediate between TE01 and HE11 (which has an ideal radiation pattern). The squeeze and orientation of the TM11 polarizer are adjusted to compensate both for the birefringence of a corrugated bend propagating HE11 and for a flat mirror inside PLT that reverses the sense of rotation of the polarization. 11 refs., 8 figs
National Spherical Torus Experiment (NSTX)
International Nuclear Information System (INIS)
Masayuki Ono
2000-01-01
The main aim of National Spherical Torus Experiment (NSTX) is to establish the fusion physics principles of the innovative spherical torus (ST) concept. Physics outcome of the NSTX research program is relevant to near-term applications such as the Volume Neutron Source (VNS) and burning plasmas, and future applications such as the pilot and power plants. The NSTX device began plasma operations in February 1999 and the plasma current was successfully ramped up to the design value of 1 million amperes (MA) on December 14, 1999. The CHI (Coaxial Helicity Injection) and HHFW (High Harmonic Fast Wave) experiments have also started. Stable CHI discharges of up to 133 kA and 130-msec duration have been produced using 20 kA of injected current. Using eight antennas connected to two transmitters, up to 2 MW of HHFW power was successfully coupled to the plasma. The Neutral-beam Injection (NBI) heating system and associated NBI-based diagnostics such as the Charge-exchange Recombination Spectrometer (CHERS) will be operational in October 2000
Neoclassical transport associated with collisionless detrapping in a bumpy torus
International Nuclear Information System (INIS)
Hastings, D.E.
1983-10-01
In the two collisionality nonresonant regime in a bumpy torus the transitional particles can make a large contribution to neoclassical transport. This contribution can be moderated by the toroidally induced radial drift which causes transitional particles to detrap and retrap in the mirror sectors. This effect leads to diffusion coefficients which are linear in the collision frequency and scale with the inverse aspect ratio instead of the more usual square of the inverse aspect ratio. (author)
Acceleration of a compact torus
International Nuclear Information System (INIS)
Hartmann, C.W.; Eddleman, J.L.; Hammer, J.H.; Kusse, B.
1987-01-01
The authors report the first results of a study of acceleration of spheromak-type compact toruses in the RACE experiment (plasma Ring ACceleration Experiment). The RACE apparatus consists of (1) a magnetized, coaxial plasma gun 50 cm long, 35 cm OD, 20 cm ID, (2) 600 cm long coaxial acceleration electrodes 50 cm OD, 20 cm ID, (3) a 250 kJ electrolytic capacitor bank to drive the gun solenoid for initial magnetization, (4) a 200 kJ gun bank, (5) a 260 kJ accelerator bank, and (6) magnetic probes and other diagnostics, and vacuum apparatus. To outer acceleration electrode is an extension, at larger OD, of the gun outer electrode, and the inner acceleration electrode is supported and fed by a coaxial insert in the gun center electrode as shown
Studies of accelerated compact toruses
International Nuclear Information System (INIS)
Hartman, C.W.; Eddleman, J.; Hammer, J.H.
1983-01-01
In an earlier publication we considered acceleration of plasma rings (Compact Torus). Several possible accelerator configurations were suggested and the possibility of focusing the accelerated rings was discussed. In this paper we consider one scheme, acceleration of a ring between coaxial electrodes by a B/sub theta/ field as in a coaxial rail-gun. If the electrodes are conical, a ring accelerated towards the apex of the cone undergoes self-similar compression (focusing) during acceleration. Because the allowable acceleration force, F/sub a/ = kappaU/sub m//R where (kappa - 2 , the accelerating distance for conical electrodes is considerably shortened over that required for coaxial electrodes. In either case, however, since the accelerating flux can expand as the ring moves, most of the accelerating field energy can be converted into kinetic energy of the ring leading to high efficiency
Methanol in the L1551 Circumbinary Torus
White, Glenn J.; Fridlund, C. W. M.; Bergman, P.; Beardsmore, A.; Liseau, Rene; Phillips, R. R.
2006-01-01
We report observations of gaseous methanol in an edge-on torus surrounding the young stellar object L1551 IRS5. The peaks in the torus are separated by ~ 10,000 AU from L1551 IRS5, and contain ~ 0.03 earth masses of cold methanol. We infer that the methanol abundance increases in the outer part of the torus, probably as a result of methanol evaporation from dust grain surfaces heated by the shock luminosity associated with the shocks associated with the jets of an externally located x-ray sou...
Fabrication of a 40-inch diameter ceramic to metal seal for PLT
International Nuclear Information System (INIS)
Lewin, G.; Mullaney, D.
1976-01-01
The design and fabrication details for the ceramic to metal seal for PLT are presented. The method used for the successful casting and firing of the 90% Al 2 O 3 ceramic body and the subsequent grinding and brazing of the ceramic to 430 S.S. are discussed
Coordination of growth in root and shoot apices by AIL/PLT transcription factors
Scheres, Ben; Krizek, Beth A.
2018-01-01
Growth at the root tip and organ generation at the shoot tip depend on the proper functioning of apical meristems and the transitioning of meristematic cell descendants from a proliferating state to cell elongation and differentiation. Members of the AINTEGUMENTA-LIKE/PLETHORA (AIL/PLT)
Fusion product measurements of the local ion thermal diffusivity in the PLT tokamak
International Nuclear Information System (INIS)
Heidbrink, W.W.; Lovberg, J.; Strachan, J.D.; Bell, R.E.
1986-03-01
Measurement of the gradient of the d-d fusion rate profile in an ohmic PLT plasma is used to deduce the gradient of the ion temperature and, thus, the local ion thermal diffusivity through an energy balance analysis. The inferred ion diffusivity is consistent with neoclassical theory
Short interval expansion of Rényi entropy on torus
Energy Technology Data Exchange (ETDEWEB)
Chen, Bin [Department of Physics and State Key Laboratory of Nuclear Physics and Technology,Peking University,5 Yiheyuan Rd, Beijing 100871 (China); Collaborative Innovation Center of Quantum Matter,5 Yiheyuan Rd, Beijing 100871 (China); Center for High Energy Physics, Peking University,5 Yiheyuan Rd, Beijing 100871 (China); Wu, Jun-Bao [Theoretical Physics Division, Institute of High Energy Physics, Chinese Academy of Sciences,19B Yuquan Rd, Beijing 100049 (China); Theoretical Physics Center for Science Facilities, Chinese Academy of Sciences,19B Yuquan Rd, Beijing 100049 (China); Center for High Energy Physics, Peking University,5 Yiheyuan Rd, Beijing 100871 (China); Zhang, Jia-ju [Theoretical Physics Division, Institute of High Energy Physics, Chinese Academy of Sciences,19B Yuquan Rd, Beijing 100049 (China); Theoretical Physics Center for Science Facilities, Chinese Academy of Sciences,19B Yuquan Rd, Beijing 100049 (China)
2016-08-23
We investigate the short interval expansion of the Rényi entropy for two-dimensional conformal field theory (CFT) on a torus. We require the length of the interval ℓ to be small with respect to the spatial and temporal sizes of the torus. The operator product expansion of the twist operators allows us to compute the short interval expansion of the Rényi entropy at any temperature. In particular, we pay special attention to the large c CFTs dual to the AdS{sub 3} gravity and its cousins. At both low and high temperature limits, we read the Rényi entropies to order ℓ{sup 6}, and find good agreements with holographic results. Moreover, the expansion allows us to read 1/c contribution, which is hard to get by expanding the thermal density matrix. We generalize the study to the case with the chemical potential as well.
The classical theory of the bumpy torus relativistic annulus
International Nuclear Information System (INIS)
Hamasaki, S.; Krall, N.A.; Sperling, J.L.
1983-01-01
The relativistic electron annulus is a critical component of the bumpy torus magnetic fusion concept. An analysis of the annulus is presented in which the ring steady state is determined by the explicit balance of quasi-linear heating and classical losses, i.e. collisions and synchrotron radiation. Both anisotropy and loss-cone effects are included in the formalism. It is demonstrated that a large number of electron cyclotron harmonics, not just the first and second, contribute in an appreciable way to annulus steady state and power balance. Without a loss cone, the analysis reproduces the relativistic passing electron population observed in bumpy tori on confined drift surfaces near the centre of the bumpy torus cross-section. Loss-cone effects permit an annulus population with large perpendicular pressure to exist. It is shown that the balance between quasi-linear heating and the classical losses cannot account for the experimental scaling of bumpy torus annulus temperature; therefore, processes not included in the classical ring power balance model must contribute in a non-trivial way to observed annulus properties. (author)
Tool path in torus tool CNC machining
Directory of Open Access Journals (Sweden)
XU Ying
2016-10-01
Full Text Available This paper is about tool path in torus tool CNC machining.The mathematical model of torus tool is established.The tool path planning algorithm is determined through calculation of the cutter location,boundary discretization,calculation of adjacent tool path and so on,according to the conversion formula,the cutter contact point will be converted to the cutter location point and then these points fit a toolpath.Lastly,the path planning algorithm is implemented by using Matlab programming.The cutter location points for torus tool are calculated by Matlab,and then fit these points to a toolpath.While using UG software,another tool path of free surface is simulated of the same data.It is drew compared the two tool paths that using torus tool is more efficient.
Feasibility study for the Spherical Torus Experiment
International Nuclear Information System (INIS)
Lazarus, E.A.; Attenberger, S.E.; Baylor, L.R.
1985-10-01
The design of the Spherical Torus Experiment (STX) is discussed. The physics of the plasma are given in a magnetohydrodynamic model. The structural aspects and instrumentation of the device are described. 19 refs., 103 figs
Torus bifurcations in multilevel converter systems
DEFF Research Database (Denmark)
Zhusubaliyev, Zhanybai T.; Mosekilde, Erik; Yanochkina, Olga O.
2011-01-01
embedded one into the other and with their basins of attraction delineated by intervening repelling tori. The paper illustrates the coexistence of three stable tori with different resonance behaviors and shows how reconstruction of these tori takes place across the borders of different dynamical regimes....... The paper also demonstrates how pairs of attracting and repelling tori emerge through border-collision torus-birth and border-collision torus-fold bifurcations. © 2011 World Scientific Publishing Company....
Wendelstein 7-X Torus Hall Layout and System Integration
International Nuclear Information System (INIS)
Hartmann, D.; Damiani, C.; Hartfuss, H.-J.; Krampitz, R.; Neuner, U.
2006-01-01
Wendelstein 7-X is an experimental fusion device presently under construction in Greifswald, Germany, to study the stellarator concept at reactor relevant parameters und steady-state conditions. The heart of the machine consists of the torus that houses the superconducting coils and the plasma vacuum vessel. It is located nearly in the center of a 30 m x 30 m x 20 m hall. A large number of components need to be placed in close proximity of the torus to provide the system with the required means, e.g. cryogenic gases, cooling water, electricity, and to integrate it with the peripheral diagnostic and heating components. The arrangement of these components has to be supported by suitable structures, and has to be optimized to allow for installation, maintenance, and repair. In addition, space has to be provided for escape routes and for sufficient distance between components that could negatively influence each other's performance, etc. The layout of the components has been done over many years using 3D CAD software. It was based on simple geometric models of the components and of the additionally required space. Presently the layout design is being detailed and updated by replacing the original coarse models with more refined estimates or - in some cases - with as-built models. All interface requirements are carefully taken into account. Detailed routing was specified for the cryo and cooling water supply lines whose design and installation is outsourced. Due to the limited space available and severely restricted access during experimental campaigns, the requirement to put auxiliary components like electronic racks into the torus hall is being queried. The paper summarizes the present state of the component layout in the torus hall, and how the peripheral supply, diagnostics, and heating systems are integrated into the machine. (author)
Final report on the LLNL compact torus acceleration project
International Nuclear Information System (INIS)
Eddleman, J.; Hammer, J.; Hartman, C.; McLean, H.; Molvik, A.
1995-01-01
In this report, we summarize recent work at LLNL on the compact torus (CT) acceleration project. The CT accelerator is a novel technique for projecting plasmas to high velocities and reaching high energy density states. The accelerator exploits magnetic confinement in the CT to stably transport plasma over large distances and to directed kinetic energies large in comparison with the CT internal and magnetic energy. Applications range from heating and fueling magnetic fusion devices, generation of intense pulses of x-rays or neutrons for weapons effects and high energy-density fusion concepts
Fusion reaction spectra produced by anisotropic fast ions in the PLT tokamak
International Nuclear Information System (INIS)
Heidbrink, W.W.
1984-02-01
For beam-target fusion reactions, collimated measurements of the energy spectrum of one of the reaction products can provide information on the degree of anisotropy of the reacting beam ions. Measurements of the spectrum of 15 MeV protons produced by reactions between energetic 3 He ions and relatively cold deuterons during fast wave minority heating in the PLT tokamak indicate that the velocity distribution of fast 3 He ions is peaked perpendicular to the tokamak magnetic field
A measurement of the local ion temperature gradient in the PLT tokamak
International Nuclear Information System (INIS)
Lovberg, J.A.; Strachan, J.D.; Princeton Univ., NJ
1989-12-01
Local ion temperature gradients were measured at two radial positions in the PLT tokamak by counting escaping d(d,p)t protons on orbits at closely spaced intervals. A single surface barrier detector was used to make each gradient measurement, eliminating relative calibration uncertainties. The ion thermal diffusivities inferred through ion energy balance with the measured temperature gradients are within a factor of two of Chang-Hinton neoclassical values for the 3 He-minority ICRH plasmas. 12 refs., 8 figs
Yoon, Y S; Koh, S K; Jung, H J
1999-01-01
(Pb sub 1 sub - sub x La sub x)TiO sub 3 (PLT) films with various compositions of La were deposited by using the sol-gel process on quartz substrates in order to study their optical properties. X-ray patterns indicated that the pseudocubic phase of the PLT film dominated with increased La concentration due to a decrease in the lattice constant of the c-axis. Three-dimensional atomic force microscopy images revealed that the grain size and root mean square (r.m.s) surface roughness were decreased by adding of La. The optical band gap of the as-deposited films became wider when Pb was replaced with La, which could be calculated from the transmittance of an UV-visible spectrometer. The addition of La increased the transparency of the PbTiO sub 3 film and shifted the threshold to shorter wavelengths for initiation of absorption. In addition, we modified the surfaces of the PLT films with La concentrations of 5 % by using an oxygen-ion beam with an oxygen-ion energy of 1 kV at different doses. The optical band gap...
Reactor assessments of advanced bumpy torus configurations
International Nuclear Information System (INIS)
Uckan, N.A.; Owen, L.W.; Spong, D.A.; Miller, R.L.; Ard, W.B.; Pipkins, J.F.; Schmitt, R.J.
1984-02-01
Recently, several innovative approaches were introduced for enhancing the performance of the basic ELMO Bumpy Torus (EBT) concept and for improving its reactor potential. These include planar racetrack and square geometries, Andreoletti coil systems, and bumpy torus-stellarator hybrids (which include twisted racetrack and helical axis stellarator - snakey torus). Preliminary evaluations of reactor implications of each approach have been carried out based on magnetics (vacuum) calculations, transport and scaling relationships, and stability properties deduced from provisional configurations that implement the approach but are not necessarily optimized. Further optimization is needed in all cases to evaluate the full potential of each approach. Results of these studies indicate favorable reactor projections with a significant reduction in reactor physical size as compared to conventional EBT reactor designs carried out in the past
Multicast Performance Analysis for High-Speed Torus Networks
National Research Council Canada - National Science Library
Oral, S; George, A
2002-01-01
... for unicast-based and path-based multicast communication on high-speed torus networks. Software-based multicast performance results of selected algorithms on a 16-node Scalable Coherent Interface (SCI) torus are given...
A disrupted molecular torus around Eta Carinae as seen in 12CO with ALMA
Smith, Nathan; Ginsburg, Adam; Bally, John
2018-03-01
We present Atacama Large Millimeter Array (ALMA) observations of 12CO 2-1 emission from circumstellar material around the massive star Eta Carinae (η Car). These observations reveal new structural details about the cool equatorial torus located ˜4000 au from the star. The CO torus is not a complete azimuthal loop, but rather, is missing its near side, which appears to have been cleared away. The missing material matches the direction of apastron in the eccentric binary system, making it likely that η Car's companion played an important role in disrupting portions of the torus soon after ejection. Molecular gas seen in ALMA data aligns well with the cool dust around η Car previously observed in mid-infrared (IR) maps, whereas hot dust resides at the inner surface of the molecular torus. The CO also coincides with the spatial and velocity structure of near-IR H2 emission. Together, these suggest that the CO torus seen by ALMA is actually the pinched waist of the Homunculus polar lobes, which glows brightly because it is close to the star and warmer than the poles. The near side of the torus appears to be a blowout, associated with fragmented equatorial ejecta. We discuss implications for the origin of various features north-west of the star. CO emission from the main torus implies a total gas mass in the range of 0.2-1 M⊙ (possibly up to 5 M⊙ or more, although with questionable assumptions). Deeper observations are needed to constrain CO emission from the cool polar lobes.
Pro-torus actions on Poincaré duality spaces
Indian Academy of Sciences (India)
duality spaces, Borel's dimension formula and topological splitting principle to local weights, hold if 'torus' is replaced by 'pro-torus'. Keywords. Pro-torus; Poincaré duality space; local weight. 1. Introduction. In the theory of linear representations of compact connected Lie groups, the crucial first step is restriction to the ...
Directory of Open Access Journals (Sweden)
Manuel Ramon Osorio Castillo
2014-06-01
Full Text Available ResumenLos huesos maxilares no son ajenos a las patologías que se pueden presentar en el sistema esquelético. Algunas de esas condiciones y patologías son singulares por sus características clínicas, su distribución y prevalencia. Los torus palatinos, los torus mandibulares (TM y las exostosis de los maxilares son un claro ejemplo de ellos. Hasta la presente existen ideas especulativas acerca de su etiopatogenia, de los factores asociados, de su incidencia y prevalencia, de su necesidad de tratamiento, lo que puede crear confusión entre los clínicos tanto en diagnóstico como en el manejo.El torus como tumor óseo benigno puede localizarse en el maxilar a nivel del paladar, o en la mandíbula a nivel de las tablas internas; o puede aparecer en cualquier parte del esqueleto. El TM es una exostosis o crecimiento óseo en la superficie lingual de la mandíbula. Este crecimiento ocurre generalmente cerca de la línea milohioidea, opuesto a los premolares, pero se puede extender del canino al primer molar. La mucosa que los recubre tiende a ser fina y no tolera por lo general las fuerzas de las prótesis que se colocan encima de ellos. La incidencia del torus de la mandíbula es baja en el 6% a 12.5% entre caucásicos y en los habitantes de la llanura africana. De manera contraria, algunos autores reportan una prevalencia mucho más elevada en la Costa Atlántica Colombiana.Se presenta el caso de un paciente con torus mandibulares bilaterales, con muchos años de crecimiento, hasta que por situaciones tanto fonéticas como de ulceraciones repetitivas decidió someterse al acto quirúrgico de forma bilateral. Se presentan algunas consideraciones para el manejo de esta. (Duazary 2008; 111-114AbstractThe jawbone is not a strange to the pathologies that can occur in the skeletal system. Some of these terms and conditions are unique for their clinical features, distribution and prevalence. The torus palate, jawbone torus (TM in spanish and
Electron distribution functions in Io plasma torus
International Nuclear Information System (INIS)
Boev, A.G.
2003-01-01
Electron distribution functions measured by the Voyager 1 in different shares of the Io plasma torus are explained. It is proved that their suprathermal tails are formed by the electrical field induced by the 'Jupiter wind'. The Maxwellian parts of all these spectra characterize thermal equilibrium populations of electrons and the radiation of exited ions
Surgical management of palatine Torus - case series
Directory of Open Access Journals (Sweden)
Thaís Sumie Nozu Imada
Full Text Available INTRODUCTION: Torus palatinus is a specific name to identify exostoses developed in the hard palate along the median palatine suture. Despite of not being a pathological condition, its presence requires attention and knowledge regarding its management. Surgical removal of exostoses is indicated when the patient frequently traumatizes the area of palatine torus during mastication and speech or when it is necessary for the rehabilitation of the upper arcade with complete dentures. OBJECTIVE: The aim of this article is to present three cases of Torus palatinus and to discuss the management of them. CASE REPORT: In the first case, a 57-year-old Caucasian man sought oral rehabilitation of his edentulous maxilla but presented a hard nodules in the hard palate; in the second case, a 40-year-old Caucasian woman was referred for frequent trauma of palatal mucosa during mastication, aesthetic complaint, and discomfort caused by the trauma of her tongue in this area; and in the third case, a 45-year-old Caucasian woman presented with a lesion on the palate that caused difficulty swallowing. When the Torus palatinus was impairing the basic physiological functions of the patients, all cases were surgically treated, improving the patients' quality of life. FINAL CONSIDERATION: The dentist should be properly prepared to choose the best from among the existing surgical approaches for each individual lesion in order to improve the results and avoid possible complications.
Torus palatinus | Naidoo | SA Journal of Radiology
African Journals Online (AJOL)
Kupffer and Bessel-Hagen coined the term torus palatinus in 1879 for a benign osseous protuberance arising from the midline of the hard palate. Tori are present in approximately 20% of the population and are occult until adulthood. Recent advances in modern radiology have led to improved evaluation and diagnosis of ...
Magnetostatics of the uniformly polarized torus
DEFF Research Database (Denmark)
Beleggia, Marco; De Graef, Marc; Millev, Yonko
2009-01-01
We provide an exhaustive description of the magnetostatics of the uniformly polarized torus and its derivative self-intersecting (spindle) shapes. In the process, two complementary approaches have been implemented, position-space analysis of the Laplace equation with inhomogeneous boundary condit...
Spherical torus, compact fusion at low field
International Nuclear Information System (INIS)
Peng, Y.K.M.
1985-02-01
A spherical torus is obtained by retaining only the indispensable components on the inboard side of a tokamak plasma, such as a cooled, normal conductor that carries current to produce a toroidal magnetic field. The resulting device features an exceptionally small aspect ratio (ranging from below 2 to about 1.3), a naturally elongated D-shaped plasma cross section, and ramp-up of the plasma current primarily by noninductive means. As a result of the favorable dependence of the tokamak plasma behavior to decreasing aspect ratio, a spherical torus is projected to have small size, high beta, and modest field. Assuming Mirnov confinement scaling, an ignition spherical torus at a field of 2 T features a major radius of 1.5 m, a minor radius of 1.0 m, a plasma current of 14 MA, comparable toroidal and poloidal field coil currents, an average beta of 24%, and a fusion power of 50 MW. At 2 T, a Q = 1 spherical torus will have a major radius of 0.8 m, a minor radius of 0.5 m, and a fusion power of a few megawatts
Simulations of the Effects of Jupiter's Plasma Torus on Io's Pele Plume
McDoniel, William; Goldstein, David B.; Varghese, Philip L.; Trafton, Laurence M.
2014-11-01
Io’s plumes rise hundreds of kilometers above its surface and sublimation atmosphere, presenting large targets for incoming ions from Jupiter’s plasma torus. The direct simulation Monte Carlo method is used to model the gas plume at Pele and its interaction with the Jovian plasma torus. Chemical reactions resulting from ion impacts in a plume change its composition and energy from the impacts changes the plume’s structure (asymmetrically). The presence of non-condensible daughter species in a warmer plume canopy produces a more diffuse deposition ring on Io’s surface, compared to simulations without plasma. Energized molecules also escape from the plume, forming a diffuse cloud of fast particles above the plume’s canopy, which may function to resupply the plasma torus and which suggests a mechanism for lofting other species to very high altitudes.
Design and implementation of fast charging circuit for repetitive compact torus injector
International Nuclear Information System (INIS)
Onchi, T.; McColl, D.; Dreval, M.; Wolfe, S.; Xiao, C.; Hirose, A.
2014-01-01
A novel circuit for compact torus (CT) injector operated at high repetition rates has been developed. The core technology adopted in the present work is to charge a large storage capacitor bank and quickly charge the CT capacitor bank through a stack of insulated-gate bipolar transistors (IGBTs). A system consisting of IGBTs and slow banks for the repetitive operation has been developed and installed for each discharge circuit of the University of Saskatchewan Compact Torus Injector (USCTI). A repetition rate up to 1.7 Hz and a burst of 8 CTs have been achieved
Intra HLA-D/DR region recombinant detected by primed lymphocyte typing (PLT)
DEFF Research Database (Denmark)
Jakobsen, B K; Kristensen, T; Lamm, L U
1983-01-01
The chromosome 6 markers, HLA-ABC, D, DR, MT, properdin factor Bf, and complement factors 2 (C2) and 5 (C4), were studied in three families, each of which included two HLA identical siblings, one or both of whom were known to be HLA-B: GLO recombinants. The families were also typed with primed...... lymphocyte typing (PLT) for HLA-D/DR region associated DP antigens. None of these studies gave evidence that the recombinations had occurred within the HLA region. Mixed leucocyte culture (MLC) tests within the families showed no detectable stimulation between the HLA identical siblings in two...
Observations of several disruptions in PLT using soft and ultra-soft x-ray radiation
International Nuclear Information System (INIS)
Eames, D.R.; von Goeler, S.; Sauthoff, N.R.; Stodiek, W.
1979-03-01
The evolution of ultra-soft x-ray radiation (USX, hν approx. > 100 eV) is compared to that of the soft x-ray radiation (SX, hν approx. > 1000 eV) during several disruptions in PLT. Spatial resolution is obtained in both cases by arrays of silicon surface barrier detectors viewing along different chords. During some disruptions the USX behaves quite differently from the SX, and a classification is made based on the USX behavior. Different interpretations of the data are discussed, along with the possibility that these measurements may distinguish between the roles of temperature and impurity density changes during disruptions
Performance of a modified DuoPIGatron ion source for PLT neutral beam injectors
International Nuclear Information System (INIS)
Tsai, C.C.; Stirling, W.L.; Haselton, H.H.
1978-09-01
The performance of a modified duoPIGatron ion source for PLT neutral beam injectors is described. The 22-cm source has been operated to deliver beams of 70 A, up to 45 keV, and 0.5 sec. Following a brief review of source operation, the dominant reactions leading to an enhanced atomic ion fraction in the source plasma are emphasized. In addition to the high atomic ion species yield (about 85%), other important characteristics of the source such as high arc efficiency (about 1.1 A ion beam current per kW of arc power), long filament lifetime, high reliability, and scalability are also described
Angular distribution of the bremsstrahlung emission during lower-hybrid current drive on PLT
International Nuclear Information System (INIS)
von Goeler, S.; Stevens, J.; Bernabei, S.
1985-06-01
The bremsstrahlung emission from the PLT tokamak during lower-hybrid current drive has been measured as a function of angle between the magnetic field and the emission direction. The emission is peaked strongly in the forward direction, indicating a strong anisotropy of the electron-velocity distribution. The data demonstrate the existence of a nearly flat tail of the velocity distribution, which extends out to approximately 500 keV and which is interpreted as the plateau created by Landau damping of the lower-hybrid waves
International Nuclear Information System (INIS)
Wouters, A.; Schwob, J.L.; Suckewer, S.; Seely, J.F.; Feldman, U.; Dave, J.H.
1988-03-01
High resolution spectra of the elements Fe, Ni, Zn, Ge, Se, and Mo injected into the PLT tokamak were recorded by the 2-meter Schwob-Fraenkel soft X-ray multichannel spectrometer (SOXMOS). Spectra were recorded every 50 ms during the time before and after injection. The spectral lines of the injected element were very strong in the spectrum recorded immedately after injection, and the transition in the injected element were easily distinguished from the transitions in te intrinsic elements (C, O, Ti, Cr, Fe, and Ni). An accurate wavelength scale was established using well-known reference transitions in the intrinsic elements. The spectra recorded just prior to injection were substracted from the spectra recorded after injection, and the resulting spectrum was composed almost entirely of transitions from the injected element. A large number of Δn + 0 transitions between the ground and the first excited configurations in the Li I through K I isoelectronic sequences of the injected elements were identified in the wavelength region 60 /angstrom/ to 345 /angstrom/. 33 refs., 5 figs., 1 tab
Typing for HLA-D/DR associated DP-antigens with the primed lymphocyte typing (PLT) technique
DEFF Research Database (Denmark)
Morling, N; Jakobsen, B K; Platz, P
1980-01-01
A total of 74 healthy unrelated random individuals and 36 patients with juvenile rheumatoid arthritis (JRA) were typed for HLA-D antigens with the homozygous typing cell technique and typed for HLA-D/DR associated DP-antigens with the primed lymphocyte typing (PLT) technique. All patients and some...... of the controls were also HLA-DR typed with a limited battery of anti-DR sera. Selected PLT-cells, specific for the HLA-D/DR antigens D/DRw1-8 and the local specificity D"H" were used. The results of the PLT-experiments were evaluated with the Normalized Median Response (NMR) method and the further procedure...
Neutron sawtooth behavior in the PLT, DIII-D, and TFTR tokamaks
International Nuclear Information System (INIS)
Lovberg, J.A.; Heidbrink, W.W.; Strachan, J.D.; Zaveryaev, V.S.
1988-10-01
The effect of the sawtooth instability on the 2.5 MeV neutron emission in the PLT, DIII-D, and TFTR tokamaks is studied. In thermonuclear plasmas, the instability typically results in a 20% reduction in emission. The time evolution of the thermonuclear neutron signal suggests that the sawtooth crash consists of four phases. First, the electron density profile flattens rapidly (in /approximately/30μsec on PLT) but, in some cases, there is little associated change in neutron emission, suggesting that most reacting ions remain confined in the sawtooth region but do not completely mix. After the electron sawtooth, the ions continue to mix, resulting in a /approximately/10% reduction in neutron emission in /approximately/0.5 msec. The emission then decays more slowly during the final two phases. Thermalization of reacting ions on a /approximately/3/tau//sub ii/ time scale accounts for only /approximately/20% of the slow drop. Most of the slow drop seems to be caused by loss of ion energy from the mixing region (an ion heat pulse). 36 refs., 15 figs., 1 tabs
Start-up and ramp-up of the PLT tokamak by lower hybrid waves
International Nuclear Information System (INIS)
Jobes, F.C.; von Goeler, S.; Bernabei, S.
1985-01-01
Lower hybrid current drive (LHCD) is an inherently steady-state means of maintaining the poloidal field of a tokamak reactor. However, the energy losses of LHCD, which are proportional to density, are projected to be too great in a fusion reactor for LHCD to be economically feasible during the burn state of the reaction cycle. The authors maintain that LHCD could be extremely useful in restoring poloidal field energy between burns. In situations not requiring a rapid build up, LHCD appears, by extrapolation from present experiments, to be capable of supplying the full required poloidal field energy. In this paper, experiments have been performed on PLT and other tokamaks to examine the role of LHCD in start-up and ramp-up, as well as to examine the efficiency of stady-state current drice. Both the start-up and the ramp-up experiments were quite successful, with the start-up experiment obtaining currents up to 20% of full current for PLT, and the ramp-up experiments obtaining ramp-up efficiencies of approximately 20%
Confinement studies with neutral-beam injection on PDX and PLT
Energy Technology Data Exchange (ETDEWEB)
Goldston, R.; Kaye, S.; Davis, S.
1982-07-01
Neutral beam injection experiments on PLT and PDX have been conducted over a wider range in parameter space than previously. On PLT H/sup 0/ beams have been injected into well-confined high toroidal field, high density Ohmic plasmas, giving n/sub e/(0) tau/sub Ee/ products during injection of up to 5 x 10/sup 12/ sec cm/sup -3/. tau/sub Ee/ is found to rise slowly with increasing density in these experiments. Comparing these results with earlier (1979) discharges, which showed much lower heating efficiency, the importance of starting with a hot Ohmic plasma and a peaked density profile is striking. On PDX high power injection experiments over a range in plasma current have shown a significant variation with current of both ion heating and total stored plasma energy. Transport analysis of these results indicates that global confinement drops little when I/sup p/ is varied from 480 to 320 kA, but as I/sup p/ falls to 200 kA, tau/sub E/ deteriorates significantly.
Drift resonance and stability of the Io plasma torus
Zhan, Jie; Hill, T. W.
2000-03-01
The observed local time asymmetry of the Io plasma torus is generally attributed to the presence of a persistent dawn-to-dusk electric field in the Jovian magnetosphere. The local time asymmetry is modulated at the System 3 rotation period of Jupiter's magnetic field, suggesting that the dawn-to-dusk electric field may be similarly modulated. We argue that such a System 3 modulation would have a profound disruptive effect on the observed torus structure if the torus were to corotate at exactly the System 3 rate: the torus would be a resonantly forced harmonic oscillator, and would disintegrate in a few rotation periods, contrary to observations. This destabilizing effect is independent of, and in addition to, the more familiar effect of the centrifugal interchange instability, which is also capable of disrupting the torus in a few rotation periods in the absence of other effects. We conclude that the observed (few percent) corotation lag of the torus is essential to preserving the observed long-lived torus structure by detuning the resonant frequency (the torus drift frequency) relative to the forcing frequency (System 3). A possible outcome of this confinement mechanism is a residual radial oscillation of the torus at the beat period (~10 days) between System 3 and the torus drift period.
A new equilibrium torus solution and GRMHD initial conditions
Penna, Robert F.; Kulkarni, Akshay; Narayan, Ramesh
2013-11-01
Context. General relativistic magnetohydrodynamic (GRMHD) simulations are providing influential models for black hole spin measurements, gamma ray bursts, and supermassive black hole feedback. Many of these simulations use the same initial condition: a rotating torus of fluid in hydrostatic equilibrium. A persistent concern is that simulation results sometimes depend on arbitrary features of the initial torus. For example, the Bernoulli parameter (which is related to outflows), appears to be controlled by the Bernoulli parameter of the initial torus. Aims: In this paper, we give a new equilibrium torus solution and describe two applications for the future. First, it can be used as a more physical initial condition for GRMHD simulations than earlier torus solutions. Second, it can be used in conjunction with earlier torus solutions to isolate the simulation results that depend on initial conditions. Methods: We assume axisymmetry, an ideal gas equation of state, constant entropy, and ignore self-gravity. We fix an angular momentum distribution and solve the relativistic Euler equations in the Kerr metric. Results: The Bernoulli parameter, rotation rate, and geometrical thickness of the torus can be adjusted independently. Our torus tends to be more bound and have a larger radial extent than earlier torus solutions. Conclusions: While this paper was in preparation, several GRMHD simulations appeared based on our equilibrium torus. We believe it will continue to provide a more realistic starting point for future simulations.
Equilibrium-torus bifurcation in nonsmooth systems
DEFF Research Database (Denmark)
Zhusubahyev, Z.T.; Mosekilde, Erik
2008-01-01
Considering a set of two coupled nonautonomous differential equations with discontinuous right-hand sides describing the behavior of a DC/DC power converter, we discuss a border-collision bifurcation that can lead to the birth of a two-dimensional invariant torus from a stable node equilibrium...... point. We obtain the chart of dynamic modes and show that there is a region of parameter space in which the system has a single stable node equilibrium point. Under variation of the parameters, this equilibrium may disappear as it collides with a discontinuity boundary between two smooth regions...... in the phase space. The disappearance of the equilibrium point is accompanied by the soft appearance of an unstable focus period-1 orbit surrounded by a resonant or ergodic torus. Detailed numerical calculations are supported by a theoretical investigation of the normal form map that represents the piecewise...
Torus II. Technical description of the design proposal
International Nuclear Information System (INIS)
Aymar, R.; Deck, C.; Deschamps, P.; Lafon, D.; Leloup, C.; Pariente, M.; Renaud, C.; Sledziewski, Z.; Torossian, A.
1976-06-01
A new Tokamak device, called TORUS II, is proposed to be built inside the EURATOM-CEA Association. This is a large machine: I=1.7MA; B=30kGs; R=1.8m; a=75cm, designed to be a successor to TFR and to follow the lines of research already initiated in the present TFR programme, i.e. on plasma heating, on impurities, on energy confinement and scaling laws, providing to JET a very efficient backing. This part of the report provides a technical description of the main components of the basic machine, according to the state of design reached in June 1976. Every subsystem whose assembly forms the basic machine is the subject of one section: vacuum vessel, toroidal field coils, poloidal field system, mechanical structures, monitoring, control and data acquisition, and power supplies. The first part in each section attempts to summarize the solution that was retained, pointing out the problems to be solved and the choice made. No contribution takes into account the problems of installation and buildings and the time schedule which is given is only concerned with the simplest solution. By way, contributions are given which show the state of development of the peripheral systems envisaged for TORUS II, mainly: additional heating, control of impurities and plasma diagnostics [fr
Torus-doubling process via strange nonchaotic attractors
International Nuclear Information System (INIS)
Mitsui, Takahito; Uenohara, Seiji; Morie, Takashi; Horio, Yoshihiko; Aihara, Kazuyuki
2012-01-01
Torus-doubling bifurcations typically occur only a finite number of times. It has been assumed that torus-doubling bifurcations in quasiperiodically forced systems are interrupted by the appearance of strange nonchaotic attractors (SNAs). In the present Letter, we study a quasiperiodically forced noninvertible map and report the occurrence of a torus-doubling process via SNAs. The mechanism of this process is numerically clarified. Furthermore, this process is experimentally demonstrated in a switched-capacitor integrated circuit. -- Highlights: ► We report the occurrence of a torus-doubling process via strange nonchaotic attractors (SNAs). ► The process consists of the gradual fractalization of a torus and the Heagy–Hammel transition. ► The torus-doubling process via SNAs is also experimentally demonstrated in an electronic circuit.
Payan, A. P.; Rajendar, A.; Paty, C. S.; Bonfond, B.; Crary, F.
2012-12-01
Io is the primary source of plasma in the Jovian magnetosphere, continuously releasing approximately 1 ton/s of SO2 from volcanic eruptions. The interaction of Io with Jupiter's magnetosphere is strongly influenced by the density structure of the resulting plasma torus and the position of Io relative to the center of the torus [Bonfond et al. 2008]. This unusual interaction produces a complex auroral feature on Jupiter's ionosphere known as the Io footprint. Hubble Space Telescope (HST) observations of Jupiter's far-UV aurora during spring 2007 showed an increased number of isolated auroral blobs along with a continuous expansion of Jupiter's main auroral oval over a few months. These blobs were associated with several large injections of hot plasma between 9 and 27 Jovian radii. These events coincided with a large volcanic eruption of the Tvashtar Paterae on Io, as observed by the New Horizons spacecraft [Spencer et al., 2007]. This, in turn, may have resulted in a significant increase in the plasma torus density. Besides, on June 7th, 2007, the Io footprint momentarily became so faint that it disappeared under a diffuse patch of emission remaining from an injection blob [Bonfond et al., 2012]. The goal of the present study is to examine the relationship between the increased density of the plasma torus and the dimming of the Io footprint. We implement a 2D model of the Io plasma torus that treats the variable-density torus as being composed of discrete layers of uniform density. As the co-rotating plasma in the plasma torus impinges on Io, Alfvén waves are launched at a pushback angle obtained from Gurnett and Goertz [1981]. The waves propagate inside the plasma torus through reflection and refraction at density discontinuities where they lose some of their initial energy. Using the above model, we can track the Alfvén wave fronts in the plasma torus and determine the longitude at which they exit the torus along with the corresponding remaining energy. Since
International Nuclear Information System (INIS)
Medley, S.S.
1981-07-01
The Charge Exchange Neutral Analyzer (CENA) for TFTR is designed to measure singly charged ion species of atomic mass A = 1, 2, and 3 simultaneously with up to 75 energy channels per mass and an energy range of 0.5 3 charge exchange neutrals makes the analyzer of particular interest for recently proposed fast He 3 ++ diagnostics during ICRF heating on PLT
DEFF Research Database (Denmark)
Ødum, Niels; Hartzman, R; Jakobsen, B K
1986-01-01
Lymphocytes from highly selected donors were primed for 10 days and subsequently bulk-expanded in IL 2 (TCGF) containing cultures. Two well-discriminatory PLT (CDP = Copenhagen DP) reagents against each of the DPw1-w6 specificities and one against each of the two "new" specificities, CDP4s...
Terzich, M; Quarles, C; Goodwin, M A; Brown, J
1998-01-01
In previous studies, Poultry Litter Treatment(R) (PLT(R)) was shown to reduce atmospheric ammonia levels and ascites death rates, and produce higher profit value in broiler chickens. The purpose of the present study was to determine the effect of PLT(R) on atmospheric ammonia levels, the development of respiratory tract lesions, and body weight gains in broiler chickens. Data were collected from chicks that were raised in containment conditions that resembled commercial settings. Atmospheric ammonia levels, gross thoracic air sac lesion scores, and the numbers and magnitudes of histopathologic tracheal mucosal injuries were significantly (P = 0.001) reduced in chickens that were raised on PLT(R)-treated litter than in their untreated-litter control counterparts. In addition, mean body weights and lung:body weight ratios were significantly (P broilers that were raised on treated litter. The reductions in respiratory tract lesions among broilers raised on PLT(R)-treated litter were attributed to reductions in atmospheric ammonia levels.
A study of disruptive instabilities in the PLT tokamak using X-ray techniques
International Nuclear Information System (INIS)
Sauthoff, N.R.; Goeler, S. von; Stodiek, W.
1978-01-01
Disruptive instabilities in PLT have been analysed by using an array of surface barrier X-ray detectors viewing the plasma cross-section along 20 chords. A wide variety of phenomena has been observed. A system of classification has been attempted, based upon: (1) the severity of the disruption, (2) the dominant precursor oscillations, and (3) the location of the onset of the disruption. Minor disruptions, in which the disruption does not appear at the location of the island of the precursor oscillation, have been observed, sometimes accompanied by seemingly independent higher-frequency oscillations of different helicity localized near the point of the disruption. Major disruptions exhibit flatter central q-profiles, slowing of the oscillations, asymmetry with respect to the centre of the discharge, and a correlation with high-Z impurity radiation. (author)
Intra HLA-D/DR region recombinant detected by primed lymphocyte typing (PLT)
DEFF Research Database (Denmark)
Jakobsen, B K; Kristensen, T; Lamm, L U
1983-01-01
lymphocyte typing (PLT) for HLA-D/DR region associated DP antigens. None of these studies gave evidence that the recombinations had occurred within the HLA region. Mixed leucocyte culture (MLC) tests within the families showed no detectable stimulation between the HLA identical siblings in two......The chromosome 6 markers, HLA-ABC, D, DR, MT, properdin factor Bf, and complement factors 2 (C2) and 5 (C4), were studied in three families, each of which included two HLA identical siblings, one or both of whom were known to be HLA-B: GLO recombinants. The families were also typed with primed...... to reactive reagents. One of these (GHx), reacted with a determinant which segregated within the GG family as if child G was a paternal recombinant between the HLA-D, DR, DP, and C4 loci, on the one hand, and on the other hand one or more loci governing other HLA-D/DR region controlled lymphocyte activating...
EW[OIII] as an Orientation Indicator for Quasars: Implications for the Torus
Energy Technology Data Exchange (ETDEWEB)
Bisogni, Susanna [Harvard-Smithsonian Center for Astrophysics, Cambridge, MA (United States); Osservatorio Astrofisico di Arcetri, INAF, Florence (Italy); Marconi, Alessandro; Risaliti, Guido [Osservatorio Astrofisico di Arcetri, INAF, Florence (Italy); Dipartimento di Fisica e Astronomia, Università degli Studi di Firenze, Florence (Italy); Lusso, Elisabeta, E-mail: susanna.bisogni@cfa.harvard.edu [Centre for Extragalactic Astronomy, Department of Physics, Durham University, Durham (United Kingdom)
2017-11-21
We present an analysis of the average spectral properties of 12,000 SDSS quasars as a function of accretion disc inclination, as measured from the equivalent width of the [OIII] 5007Å line. The use of this indicator on a large sample of quasars from the SDSS DR7 has proven the presence of orientation effects on the features of UV/optical spectra, confirming the presence of outflows in the NLR gas and that the geometry of the BLR is disc-like. Relying on the goodness of this indicator, we are now using it to investigate other bands/components of AGN. Specifically, the study of the UV/optical/IR SED of the same sample provides information on the obscuring “torus.” The SED shows a decrease of the IR fraction moving from face-on to edge-on sources, in agreement with models where the torus is co-axial with the accretion disc. Moreover, the fact we are able to observe the broad emission lines also in sources in an edge-on position, suggests that the torus is rather clumpy than smooth as in the Unified Model. The behavior of the SED as a function of EW[OIII] is in agreement with the predictions of the clumpy torus models as well.
Formation of a compact torus using a toroidal plasma gun
International Nuclear Information System (INIS)
Levine, M.A.; Pincosy, P.A.
1981-01-01
Myers, Levine and Pincosy earlier reported results using a toroidal plasma gun. The device differs from the usual coaxial plasma gun in the use of a strong toroidal bias current for enhanced efficiency, a pair of disk-like accelerating electrodes for reduced viscosity and a fast pulsed toroidal gas valve for more effective use of the injected gas sample. In addition, a technique is used for generating a toroidal current in the plasma ring. The combination offers an opportunity to deliver a plasma with a large amount of energy and to vary the density and relative toroidal and poloidal magnetic field intensities over a range of values. It is the purpose of this paper to report further experimental results, to project the gun's applications to the formation of a compact torus, and to propose a simple modification of the present apparatus as a test
Space potential profiles in ELMO Bumpy Torus (EBT) experiment
International Nuclear Information System (INIS)
Bieniosek, F.M.; Connor, K.A.
1983-01-01
Spatially resolved measurements of the electric space potential in the ELMO Bumpy Torus (EBT) have been made by a heavy ion beam probe. The EBT-I device is characterized by positive potentials in the surface plasma the order of 100 V and by a nearly symmetric potential well in the core plasma of up to 300 V with respect to the surface potential. The EBT-S device has a similar potential structure with well depth and peak potential similar to or greater than that of EBT-I. Peak potential and well depth increase as the edge gas pressure is lowered and as the microwave power is increased. The potential structure is strongly linked to the specific heating geometry. The ambipolar electric field is large enough generally to dominate the core electron neoclassical diffusion. The potential profile is approximately parabolic in the core, which is shown to be a natural consequence of the spatially uniform plasma source function
International Nuclear Information System (INIS)
Betta, G; Capriglione, D; Ferrigno, L; Laracca, M
2009-01-01
Power line telecommunication (PLT) technology offers cheap and fast ways for providing in-home broadband services and local area networking. Its main advantage is due to the possibility of using the pre-existing electrical grid as a communication channel. Nevertheless, technical challenges arise from the difficulty of operating on a hostile medium, not designed for communication purposes, characterized by complex channel modeling and by varying time response. These aspects put practical problems for designers and testers in the assessment of network quality of service performance parameters such as the throughput, the latency, the jitter, and the reliability. The measurement of these parameters has not yet been standardized so that there do not exist reference test set-ups and measurement methodologies (i.e. the type of isolation from the ac main, the observation time and the number of experiments, the measurement uncertainty and so on). Consequently, experiments executed by adopting different methods may lead to incompatible measurement results, thus making it also impossible to have reliable comparisons of different PLT modems. Really, the development of standard procedures is a very difficult task because the scenarios in which the PLT modems can work are very wide and then the application of an exhaustive approach (in which all the parameters influencing the PLT performance should be considered) would be very complex and time consuming, thus making the modem characterization very expensive. In this paper, the authors propose a methodological approach to develop an efficient measurement procedure able to reliably assess the performance of PLT modems (in terms of network quality of service parameters) with a minimum number of experiments. It is based on both creating a reconfigurable grid to which real disturbing loads are connected and implementing an original design of the experiment technique based on the effects of the uncertainty of the measurement results
Summary of US compact torus experiments
International Nuclear Information System (INIS)
Hartman, C.W.
1981-01-01
During the past several years a rapid increase has occurred in compact torus (CT) research in the United States, reflecting renewed interest in this simplified reactor consequences of this configuration. This paper reviews early approaches to CT formation and results and summarizes present experimental studies. Recent experiments have demonstrated a number of macroscopic aspects of the CT, including the conditions under which a macroscopically stable CT can be formed and maintained. Scaling experiments and more detailed studies of plasma transport in progress are discussed along with experiments under construction
The ELMO Bumpy Torus: present and future
International Nuclear Information System (INIS)
Uckan, N.A.
1978-01-01
The ELMO Bumpy Torus (EBT) experiment at ORNL was designed to circumvent the MHD stability problem encountered in standard bumpy tori by using the ''minimum-B'' properties of annular high-beta, hot-electron plasmas formed by microwave heating. The EBT combines the attractive features of both mirrors and tokamaks. The feasibility of this combined system has been demonstrated successfully in the EBT-I experiment and discussed at greater length elsewhere. The present status of the EBT research activities at ORNL is described briefly
Two dimensional critical models on a torus
International Nuclear Information System (INIS)
Saleur, H.; Di Francesco, P.
1987-01-01
After the general developments of conformal invariance in two dimensions, it was realized that the study of critical models in finite geometries, in addition to the practical information it could provide through finite size scaling, was also of great conceptual interest. The simplest example is the case of the torus, a genus 1 surface which is thus not conformally equivalent to the plane. This geometry appears quite frequently in lattice calculations for systems with periodic boundary conditions, and is also very natural from the point of view of string theory. We will discuss briefly in these notes the main results obtained so far in this simple case
The Schwinger Model on the torus
International Nuclear Information System (INIS)
Azakov, S.
1996-08-01
The classical and quantum aspects of the Schwinger model on the torus are considered. First we find explicitly all zero modes of the Dirac operator in the topological sectors with nontrivial Chern index and its spectrum. In the second part we determine the regularized effective action and discuss the propagators related to it. Finally we calculate the gauge invariant averages of the fermion bilinears and correlation functions of currents and densities. We show that in the infinite volume limit the well-known result for the chiral condensate can be obtained and the clustering property can be established. (author). 23 refs
The Columbia Non-neutral Torus
International Nuclear Information System (INIS)
Pedersen, Thomas Sunn
2009-01-01
Final report for the Columbia Non-neutral Torus. This details the results from the design, construction and initial operation of the Columbia Non-neutral Torus. During the duration of this grant, I designed, built, and operated the Columbia Nonneutral Torus, the world's lowest aspect ratio stellarator, and arguably, the world's simplest stellarator. This demonstrates the ease and robustness of the chosen stellarator design and allowed us to commence the investigation of the physics of non-neutral plasmas confined on magnetic surfaces. These plasmas are unique in many ways and had not previously been studied in a stellarator. Our first results showed that it is possible to confine and study a relatively cold pure electron plasma in a stellarator. We confirmed that the plasma is stable, and that the plasma is reasonably well confined in a stellarator configuration. These results were published in Physics of Plasmas (2006) and Physical Review Letters (2006). They enabled the existing program which is resolving the underlying transport processes in a classical stellarator with intense self-electric fields and enable the next phase of operation, electron-positron plasma physics. During the period of this grant, two students were trained in experimental plasma physics and both received their PhD degrees shortly after the grant terminated. One student is now employed in the financial services industry, the other is a postdoctoral associate at Los Alamos National Laboratory. The chief goals were to build and begin operation of the Columbia Non-neutral Torus. These goals were achieved in the third year of funding. The development of diagnostic methods and the confirmation of stable equilibria were also achieved during the grant period. In summary, the main scientific goals were all met. The main educational goals were also met, as the experiment became the training ground not only for the two aforementioned graduate students but also for a number of undergraduate students
On some Closed Magnetic Curves on a 3-torus
Energy Technology Data Exchange (ETDEWEB)
Munteanu, Marian Ioan, E-mail: marian.ioan.munteanu@gmail.com [Alexandru Ioan Cuza University of Iaşi, Faculty of Mathematics (Romania); Nistor, Ana Irina, E-mail: ana.irina.nistor@gmail.com [Gh. Asachi Technical University of Iaşi, Department of Mathematics and Informatics (Romania)
2017-06-15
We consider two magnetic fields on the 3-torus obtained from two different contact forms on the Euclidean 3-space and we study when their corresponding normal magnetic curves are closed. We obtain periodicity conditions analogues to those for the closed geodesics on the torus.
Fabrication of an alumina torus for thermonuclear fusion containment
International Nuclear Information System (INIS)
Hauth, W.E.; Blake, R.D.; Dickinson, J.M.; Rutz, H.L.; Stoddard, S.D.
1978-05-01
A 235-cm-diam torus has been fabricated for plasma containment during thermonuclear fusion experiments. This 30-cm-diam torus consists of sixty 99.5%-alumina segments, 80% of which are assembled by forming vacuum-tight ceramic-to-ceramic seals. Selection of sealing materials and techniques are discussed
Status of National Spherical Torus Experiment (NSTX)*
Ono, Masayuki
2001-10-01
The main aim of National Spherical Torus Experiment (NSTX) is to establish the fusion physics principles of the innovative spherical torus (ST) concept. The NSTX experimental facility has been operating reliably and its capabilities steadily improving. Due to relatively efficient ohmic current drive and benign halo current behavior, the plasma current was increased to 1.4 MA, which is well above the design value of 1 MA. The plasmas at 1 MA are now routinely heated by NBI to the average toroidal beta value of 20 percent range at 3 kG with electrons and ions in the 1-2 keV range. Even with the “L-mode” edge, the energy confinement time can well exceed the so-called L-mode (and even H-mode) scaling values. As a part of ST tool development, High Harmonic Fast Wave (HHFW) heating has demonstrated efficient electron heating with the central electron temperatures reaching 3.7 keV. HHFW induced H-modes have been also observed. For CHI (Coaxial Helicity Injection) non-inductive start-up, CHI discharges of up to 300 kA of toroidal current and 300 msec duration have been produced from zero current using = 25 kA of injected current. The poster presentation will also include the near term NSTX facility upgrade plan.
Recent Progress on Spherical Torus Research
Energy Technology Data Exchange (ETDEWEB)
Ono, Masayuki [PPPL; Kaita, Robert [PPPL
2014-01-01
The spherical torus or spherical tokamak (ST) is a member of the tokamak family with its aspect ratio (A = R0/a) reduced to A ~ 1.5, well below the normal tokamak operating range of A ≥ 2.5. As the aspect ratio is reduced, the ideal tokamak beta β (radio of plasma to magnetic pressure) stability limit increases rapidly, approximately as β ~ 1/A. The plasma current it can sustain for a given edge safety factor q-95 also increases rapidly. Because of the above, as well as the natural elongation κ, which makes its plasma shape appear spherical, the ST configuration can yield exceptionally high tokamak performance in a compact geometry. Due to its compactness and high performance, the ST configuration has various near term applications, including a compact fusion neutron source with low tritium consumption, in addition to its longer term goal of attractive fusion energy power source. Since the start of the two megaampere class ST facilities in 2000, National Spherical Torus Experiment (NSTX) in the US and Mega Ampere Spherical Tokamak (MAST) in UK, active ST research has been conducted worldwide. More than sixteen ST research facilities operating during this period have achieved remarkable advances in all of fusion science areas, involving fundamental fusion energy science as well as innovation. These results suggest exciting future prospects for ST research both near term and longer term. The present paper reviews the scientific progress made by the worldwide ST research community during this new mega-ampere-ST era.
Torus actions and their applications in topology and combinatorics
Buchstaber, Victor M
2002-01-01
The book presents the study of torus actions on topological spaces is presented as a bridge connecting combinatorial and convex geometry with commutative and homological algebra, algebraic geometry, and topology. This established link helps in understanding the geometry and topology of a space with torus action by studying the combinatorics of the space of orbits. Conversely, subtle properties of a combinatorial object can be realized by interpreting it as the orbit structure for a proper manifold or as a complex acted on by a torus. The latter can be a symplectic manifold with Hamiltonian torus action, a toric variety or manifold, a subspace arrangement complement, etc., while the combinatorial objects include simplicial and cubical complexes, polytopes, and arrangements. This approach also provides a natural topological interpretation in terms of torus actions of many constructions from commutative and homological algebra used in combinatorics. The exposition centers around the theory of moment-angle comple...
Tightness of the Ising-Kac Model on the Two-Dimensional Torus
Hairer, Martin; Iberti, Massimo
2018-05-01
We consider the sequence of Gibbs measures of Ising models with Kac interaction defined on a periodic two-dimensional discrete torus near criticality. Using the convergence of the Glauber dynamic proven by Mourrat and Weber (Commun Pure Appl Math 70:717-812, 2017) and a method by Tsatsoulis and Weber employed in (arXiv:1609.08447 2016), we show tightness for the sequence of Gibbs measures of the Ising-Kac model near criticality and characterise the law of the limit as the Φ ^4_2 measure on the torus. Our result is very similar to the one obtained by Cassandro et al. (J Stat Phys 78(3):1131-1138, 1995) on Z^2, but our strategy takes advantage of the dynamic, instead of correlation inequalities. In particular, our result covers the whole critical regime and does not require the large temperature/large mass/small coupling assumption present in earlier results.
An FPGA-based torus communication network
Energy Technology Data Exchange (ETDEWEB)
Pivanti, Marcello; Schifano, Sebastiano Fabio [INFN, Ferrara (Italy); Ferrara Univ. (Italy); Simma, Hubert [DESY, Zeuthen (Germany). John von Neumann-Institut fuer Computing NIC
2011-02-15
We describe the design and FPGA implementation of a 3D torus network (TNW) to provide nearest-neighbor communications between commodity multi-core processors. The aim of this project is to build up tightly interconnected and scalable parallel systems for scientific computing. The design includes the VHDL code to implement on latest FPGA devices a network processor, which can be accessed by the CPU through a PCIe interface and which controls the external PHYs of the physical links. Moreover, a Linux driver and a library implementing custom communication APIs are provided. The TNW has been successfully integrated in two recent parallel machine projects, QPACE and AuroraScience. We describe some details of the porting of the TNW for the AuroraScience system and report performance results. (orig.)
An FPGA-based torus communication network
International Nuclear Information System (INIS)
Pivanti, Marcello; Schifano, Sebastiano Fabio; Simma, Hubert
2011-02-01
We describe the design and FPGA implementation of a 3D torus network (TNW) to provide nearest-neighbor communications between commodity multi-core processors. The aim of this project is to build up tightly interconnected and scalable parallel systems for scientific computing. The design includes the VHDL code to implement on latest FPGA devices a network processor, which can be accessed by the CPU through a PCIe interface and which controls the external PHYs of the physical links. Moreover, a Linux driver and a library implementing custom communication APIs are provided. The TNW has been successfully integrated in two recent parallel machine projects, QPACE and AuroraScience. We describe some details of the porting of the TNW for the AuroraScience system and report performance results. (orig.)
Space Propulsion via Spherical Torus Fusion Reactor
International Nuclear Information System (INIS)
Williams, Craig H.; Juhasz, Albert J.; Borowski, Stanley K.; Dudzinski, Leonard A.
2003-01-01
A conceptual vehicle design enabling fast outer solar system travel was produced predicated on a small aspect ratio spherical torus nuclear fusion reactor. Analysis revealed that the vehicle could deliver a 108 mt crew habitat payload to Saturn rendezvous in 204 days, with an initial mass in low Earth orbit of 1630 mt. Engineering conceptual design, analysis, and assessment were performed on all major systems including nuclear fusion reactor, magnetic nozzle, power conversion, fast wave plasma heating, fuel pellet injector, startup/re-start fission reactor and battery, and other systems. Detailed fusion reactor design included analysis of plasma characteristics, power balance and utilization, first wall, toroidal field coils, heat transfer, and neutron/X-ray radiation
Observations of changes in residual gas and surface composition with discharge cleaning in PLT
International Nuclear Information System (INIS)
Dylla, H.F.; Bol, K.; Cohen, S.A.; Hawryluk, R.J.; Meservey, E.B.; Rossnagel, S.M.
1978-10-01
Hydrogen discharge cleaning of the PLT vacuum vessel has been studied by mass spectroscopy of desorbed gases and surface analysis of exposed samples. Several modes of vessel conditioning have been studied to date: (1) a high power discharge cleaning (PDC) mode, with a peak power density to the vessel wall P/sub s/ approximately 0.6 w/cm 2 and a peak electron temperature T/sub e/ approximately 100 ev; (2) low power (Taylor-type) discharge cleaning (TDC) with P/sub s/ approximately 0.05 w/cm 2 and T/sub e/ equal to or less than 5 eV. The predominant residual gases produced during PDC are CH 4 (1-5 x 10 -6 torr) and CO (1-10 x 10 -7 torr), whereas TDC produced primarily H 2 O (1-2 x 10 -6 torr) and CH 4 (1-10 x 10 -7 torr). In situ surface analysis of hydrocarbon-covered stainless steel has shown significant decreases in carbon coverage occurring after 10 3 -10 4 pulses of either cleaning mode. Observed changes in oxygen coverage are more difficult to interpret because of the presence of the nascent oxide layer on the stainless steel substrates
High-power ICRF and ICRF plus neutral-beam heating on PLT
International Nuclear Information System (INIS)
Hwang, D.; Bitter, M.; Budny, R.
1983-01-01
PLT ICRF experiments with RF powers up to approx.=3 MW have demonstrated efficient plasma heating in both the minority fundamental and the second harmonic ion-cyclotron regimes. In the minority 3 He regime, ion temperatures of approx.=3 keV have been produced along with approx.=1 kW of D- 3 He fusion power and substantial electron heating. In the second harmonic H regime, an equivalent averaged ion energy of approx.=4 keV has been achieved. Combined ICRF plus neutral-beam heating experiments with auxiliary powers totalling up to 4.5 MW have provided insight into auxiliary heating performance at stored plasma energy levels up to approx.=100 kJ. Values of #betta#sub(phi) in the range of 1.5-2% have been attained for Bsub(phi) approx.=17 kG. Energetic discharges with n-barsub(e) up to approx.6x10 13 cm - 3 at Bsub(phi) approx.=28 kG have also been investigated. Preliminary confinement studies suggest that energetic ion losses may contribute to a direct loss of the input RF power in the H minority heating regime but are insignificant in the 3 He minority case. The energy confinement time for the H minority regime is reduced somewhat from the Ohmic value. (author)
Start-up and ramp-up of the PLT tokamak by lower hybrid waves
International Nuclear Information System (INIS)
Jobes, F.C.; Bernabei, S.; Chu, T.K.
1985-08-01
Lower hybrid waves have been used on the PLT tokamak both to start the plasma current and to ramp it up from pre-existing levels. The waves, at 800 MHz, were launched from a 6-waveguide grill. The phasing between adjacent guides could be selected electronically, and thus the launched spectrum could be set and changed at will. For start-up, the waveguide phase difference was initially set at 0 0 in order to create a plasma, then switched to 90 0 to drive the current. Over 100 kA of plasma current, at a density of 0.5 to 1 x 10 12 cm -3 , was generated in this manner. Ramp-up experiments were performed under a wide variety of conditions. The most efficient ramp-up was found at the lowest plasma densities and with the fastest launched spectrum (n/sub e/ approx. 2 x 10 12 cm -3 , N/sub parallel/ approx. 1.6 peak); approx.20% of the launched RF power was converted to (increased) poloidal field energy. All of the ramp-up results are in excellent agreement with a theory which determines the efficiency of ramp-up from the consideration of the relative energy losses of the superthermal current-carrying electrons to collisions and to the opposing inductive E-field
Measurements of fluctuations in the flux of runaway electrons to the PLT limiter
International Nuclear Information System (INIS)
Barnes, C.W.; Strachan, J.D.
1982-07-01
Fluctuations in the flux of runaway electrons to the limiter have been measured during many PLT discharges. Oscillations at 60, 120, and 720 Hz are driven by variations in the vertical magnetic field which moves the plasma major radius. Fluctuations are seen in the range of 2 → 20 kHz due to MHD magnetic islands which extend to the plasma surface. A continuous spectrum of fluctuations is observed up to 200 kHz which correlates with drift-wave turbulence. The magnitude of the driven fluctuations can be used to measure transport properties of the runaway electrons. The amplitude of electron motion due to the MHD and drift-wave oscillations, and hence a measure of the radial size of the instability, can be determined as a function of frequency. The slope of the frequency power spectrum of the drift-wave-induced fluctuations steepens with increasing runaway electron drift orbit displacement during the current drop at the end of the discharge, and as the power in the MHD oscillations increases. A magnetic probe was used to confirm the presence of oscillating magnetic fields capable of perturbing the electron orbits
Determination of Fe charge-state distributions in PLT by Bragg crystal x-ray spectroscopy
International Nuclear Information System (INIS)
Hill, K.W.; von Goeler, S.; Bitter, M.
1978-08-01
A curved-crystal Bragg x-ray spectrometer has been used to measure Kα or 1s-2p radiation from highly stripped Fe XVIII to Fe XXV impurity ions in the PLT tokamak. The spectrometer has sufficient energy resolution (approximately < 4 eV at 6400 eV) to distinguish between the different ionization states of iron by measuring the energy shift of the Kα x rays. The measured wavelengths agree well with theory and with spectra from solar flares and from laser-produced plasmas. The distribution of Fe charge states in the center of the discharge has been inferred from a comparison of the measured x-ray spectrum with theory. The shape of the spectrum depends strongly on electron temperature (T/sub e/) in the range T/sub e/ = 800 to 1500 eV. Within the factor of two uncertainty in L-shell ionization cross sections, measured intensities agree with theory, which is based on coronal equilibrium, indicating that the ion life-time in the center of the plasma is approximately equal to or greater than the equilibration time
Ion transport studies on the PLT tokamak during neutral beam injection
International Nuclear Information System (INIS)
Suckewer, S.; Cavallo, A.; Cohen, S.
1983-12-01
Radial transport of ions during co- and counter-neutral beam heating in the PLT tokamak has been studied, using molybdenum and scandium ions as tracer elements. The time evolution of the radial profiles of several ionization stages of both elements, injected by laser blowoff during the neutral beam heating, were measured under three significantly different beam-plasma combinations. No noticeable differences in the radial profiles attributable to the beam direction were observed. However, a given injected amount resulted in considerably larger interior concentrations of the tracer element in the counter-beam heating cases, suggesting larger penetration of the plasma periphery. Computer simulation with the MIST code suggests a net inward drift of the order 10 3 cm/sec superposed to a diffusion coefficient of the order 10 4 cm 2 /sec for both scandium and molybdenum ions. Injection of larger amounts of the tracer element, sufficient to cause measurable central electron temperature changes, resulted in dramatic changes in ion-state distributions, making some appear peaked in the center while others disappeared. This effect could be produced with both co- and counter-beam heating, but with lesser amounts in the latter case. It is interpreted as rearrangement of the ionization balance, rather than any preferential accumulation of the injected element
Impurity ion transport studies on the PLT tokamak during neutral-beam injection
International Nuclear Information System (INIS)
Suckewer, S.; Cavallo, A.; Cohen, S.
1984-01-01
Radial transport of medium- and high-Z ions during co- and counter-neutral-beam heating in the PLT tokamak is studied, using molybdenum and scandium ions as tracer elements. The time evolution of the radial profiles of several ionization stages of both elements, injected by laser blowoff during the neutral-beam heating, is measured under three significantly different beam-plasma combinations. No noticeable differences in the radial profiles attributable to the beam direction are observed. However, a given injected amount resulted in considerably larger interior concentrations of the tracer element in the counter-beam heating cases, suggesting larger penetration of the plasma periphery. Computer simulation with the MIST code suggests a net inward drift of the order 10 3 cm.s -1 superposed to a diffusion coefficient of the order 10 4 cm 2 .s -1 for both scandium and molybdenum ions. Injection of larger amounts of the tracer element, sufficient to cause measurable central electron temperature changes, resulted in dramatic changes in ion-state distributions, making some appear peaked in the centre while others disappeared. This effect could be produced with both co- and counter-beam heating, but with lesser amounts in the latter case. It is interpreted as rearrangement of the ionization balance, rather than any preferential accumulation of the injected element. (author)
Effect of robust torus on the dynamical transport
International Nuclear Information System (INIS)
Martins, C G L; Carvalho, R Egydio de; Caldas, I L; Roberto, M
2010-01-01
In the present work, we quantify the fraction of trajectories that reach a specific region of the phase space when we vary a control parameter using two symplectic maps: one non-twist and another one twist. The two maps were studied with and without a robust torus. We compare the obtained patterns and we identify the effect of the robust torus on the dynamical transport. We show that the effect of meandering-like barriers loses importance in blocking the radial transport when the robust torus is present.
Current drive experiments on the HIT-II spherical torus
International Nuclear Information System (INIS)
Jarboe, T.R.; Raman, R.; Nelson, B.A.; Holcomb, C.T.; McCollam, K.J.; Sieck, P.E.
1999-01-01
This paper describes the following new achievements from the Helicity Injected Torus (HIT) program: a) formation and sustainment of a toroidal magnetic equilibrium using coaxial helicity injection (CHI) in a conducting shell that has an L/R time much shorter than the pulse length; b) static formation of a spherical torus with plasma current over 180 kA using a transformer and feedback controlled equilibrium coils; and c) production of a current increase in a transformer produced spherical torus using CHI. (author)
Current drive experiments on the HIT-II spherical torus
International Nuclear Information System (INIS)
Jarboe, T.; Raman, R.; Nelson, B.; Holcomb, C.T.; McCollam, K.J.; Sieck, P.E.
2001-01-01
This paper describes the following new achievements from the Helicity Injected Torus (HIT) program: a) formation and sustainment of a toroidal magnetic equilibrium using coaxial helicity injection (CHI) in a conducting shell that has an L/R time much shorter than the pulse length; b) static formation of a spherical torus with plasma current over 180 kA using a transformer and feedback controlled equilibrium coils; and c) production of a current increase in a transformer produced spherical torus using CHI. (author)
Field desorption and field ion surface studies of samples exposed to the plasmas of PLT and ISX
International Nuclear Information System (INIS)
Kellogg, G.L.; Panitz, J.A.
1978-01-01
Modifications to the surface of field-ion specimens exposed to plasma discharges in PLT and ISX determined by Imaging Probe, Field Ion Microscope, and Transmission Electron Microscope analysis have in the past shown several consistent features. Surface films consisting primarily of limiter material with trapped plasma and impurity species have been found to reside on samples with direct line of sight exposure to the plasma during the discharges. Control specimens placed in the tokamak, but shielded from the plasma, on the other hand, remained free of deposits. When exposed to only high power plasma discharges, samples placed at the wall position in PLT and ISX have survived the exposures with no evidence of damage or implantation. In this paper we describe the results of a recent exposure in PLT in which for the first time samples of stainless steel were included for High-Field Surface Analysis. Tokamak operating conditions, including stainless-steel limiters, titanium gettering between discharges, and the occurrence of a disruption, also distinguished this exposure from those carried out previously. Surprisingly, even with stainless-steel limiters, carbon films were found to be deposited on the samples at a rate
Benchmark experiments on neutron streaming through JET Torus Hall penetrations
Batistoni, P.; Conroy, S.; Lilley, S.; Naish, J.; Obryk, B.; Popovichev, S.; Stamatelatos, I.; Syme, B.; Vasilopoulou, T.; contributors, JET
2015-05-01
Neutronics experiments are performed at JET for validating in a real fusion environment the neutronics codes and nuclear data applied in ITER nuclear analyses. In particular, the neutron fluence through the penetrations of the JET torus hall is measured and compared with calculations to assess the capability of state-of-art numerical tools to correctly predict the radiation streaming in the ITER biological shield penetrations up to large distances from the neutron source, in large and complex geometries. Neutron streaming experiments started in 2012 when several hundreds of very sensitive thermo-luminescence detectors (TLDs), enriched to different levels in 6LiF/7LiF, were used to measure the neutron and gamma dose separately. Lessons learnt from this first experiment led to significant improvements in the experimental arrangements to reduce the effects due to directional neutron source and self-shielding of TLDs. Here we report the results of measurements performed during the 2013-2014 JET campaign. Data from new positions, at further locations in the South West labyrinth and down to the Torus Hall basement through the air duct chimney, were obtained up to about a 40 m distance from the plasma neutron source. In order to avoid interference between TLDs due to self-shielding effects, only TLDs containing natural Lithium and 99.97% 7Li were used. All TLDs were located in the centre of large polyethylene (PE) moderators, with natLi and 7Li crystals evenly arranged within two PE containers, one in horizontal and the other in vertical orientation, to investigate the shadowing effect in the directional neutron field. All TLDs were calibrated in the quantities of air kerma and neutron fluence. This improved experimental arrangement led to reduced statistical spread in the experimental data. The Monte Carlo N-Particle (MCNP) code was used to calculate the air kerma due to neutrons and the neutron fluence at detector positions, using a JET model validated up to the
A comprehensive model of ion diffusion and charge exchange in the cold Io torus
Barbosa, D. D.; Moreno, M. A.
1988-01-01
A comprehensive analytic model of radial diffusion in the cold Io torus is developed. The model involves a generalized molecular cloud theory of SO2 and its dissociation fragments SO, O2, S, and O, which are formed at a relatively large rate by solar UV photodissociation of SO2. The key component of the new theory is SO, which can react with S(+) through a near-resonant charge exchange process that is exothermic. This provides a mechanism for the rapid depletion of singly ionized sulfur in the cold torus and can account for the large decrease in the total flux tube content inward of Io's orbit. The model is used to demonstrate quantitatively the effects of radial diffusion in a charge exchange environment that acts as a combined source and sink for ions in various charge states. A detailed quantitative explanation for the O(2+) component of the cold torus is given, and insight is derived into the workings of the so-called plasma 'ribbon'.
Topological T-duality for torus bundles with monodromy
Baraglia, David
2015-05-01
We give a simplified definition of topological T-duality that applies to arbitrary torus bundles. The new definition does not involve Chern classes or spectral sequences, only gerbes and morphisms between them. All the familiar topological conditions for T-duals are shown to follow. We determine necessary and sufficient conditions for existence of a T-dual in the case of affine torus bundles. This is general enough to include all principal torus bundles as well as torus bundles with arbitrary monodromy representations. We show that isomorphisms in twisted cohomology, twisted K-theory and of Courant algebroids persist in this general setting. We also give an example where twisted K-theory groups can be computed by iterating T-duality.
Torus as phase space: Weyl quantization, dequantization, and Wigner formalism
Energy Technology Data Exchange (ETDEWEB)
Ligabò, Marilena, E-mail: marilena.ligabo@uniba.it [Dipartimento di Matematica, Università di Bari, I-70125 Bari (Italy)
2016-08-15
The Weyl quantization of classical observables on the torus (as phase space) without regularity assumptions is explicitly computed. The equivalence class of symbols yielding the same Weyl operator is characterized. The Heisenberg equation for the dynamics of general quantum observables is written through the Moyal brackets on the torus and the support of the Wigner transform is characterized. Finally, a dequantization procedure is introduced that applies, for instance, to the Pauli matrices. As a result we obtain the corresponding classical symbols.
On the energy crisis in the Io plasma torus
Smith, Robert A.; Bagenal, Fran; Cheng, Andrew F.; Strobel, Darrell
1988-01-01
Recent calculations of the energy balance of the Io plasma torus show that the observed UV and EUV radiation cannot be maintained solely via energy input by the ion pickup mechanism. Current theoretical models of the torus must be modified to include non-local energy input. It is argued that the required energy may be supplied by inward diffusion of energetic heavy ions with energies less than about 20 keV.
The geometric Schwinger model on the torus. Pt. 1
International Nuclear Information System (INIS)
Joos, H.
1990-01-01
The author analyzes the Euclidean version of the geometric Schwinger model on the torus. After the calculation of the zero mode wave functions associated with the different topological sectors, which can be expressed by θ functions defined on the two-dimensional torus, he determines the regularized effective action and discusses the propagator related to it. Finally he studies applications to the standard questions like the particle spectrum, the screening of the static potential, and the appearance of the anomaly. (HSI)
Nonlocal neoclassical transport in tokamak and spherical torus experiments
International Nuclear Information System (INIS)
Wang, W. X.; Rewoldt, G.; Tang, W. M.; Hinton, F. L.; Manickam, J.; Zakharov, L. E.; White, R. B.; Kaye, S.
2006-01-01
Large ion orbits can produce nonlocal neoclassical effects on ion heat transport, the ambipolar radial electric field, and the bootstrap current in realistic toroidal plasmas. Using a global δf particle simulation, it is found that the conventional local, linear gradient-flux relation is broken for the ion thermal transport near the magnetic axis. With regard to the transport level, it is found that details of the ion temperature profile determine whether the transport is higher or lower when compared with the predictions of standard neoclassical theory. Particularly, this nonlocal feature is suggested to exist in the National Spherical Torus Experiment (NSTX) [M. Ono, S. M. Kaye, Y.-K. M. Peng et al., Nucl. Fusion 40, 557 (2000)], being consistent with NSTX experimental evidence. It is also shown that a large ion temperature gradient can increase the bootstrap current. When the plasma rotation is taken into account, the toroidal rotation gradient can drive an additional parallel flow for the ions and then additional bootstrap current, either positive or negative, depending on the gradient direction. Compared with the carbon radial force balance estimate for the neoclassical poloidal flow, our nonlocal simulation predicts a significantly deeper radial electric field well at the location of an internal transport barrier of an NSTX discharge
Nonlinear coupling of tearing fluctuations in the Madison Symmetric Torus
International Nuclear Information System (INIS)
Sarff, J.S.; Almagri, A.F.; Cekic, M.; Den Hartog, D.J.; Fiksel, G.; Hokin, S.A.; Ji, H.; Prager, S.C.; Shen, W.; Stoneking, M.R.; Assadi, S.; Sidikman, K.L.
1992-11-01
Three-wave, nonlinear, tearing mode coupling has been measured in the Madison Symmetric Torus (MST) reversed-field pinch (RFP) [Fusion Technol. 19, 131 (1991)] using bispectral analysis of edge magnetic fluctuations resolved in ''k-space. The strength of nonlinear three-wave interactions satisfying the sum rules m 1 + m 2 = m 3 and n 1 + n 2 = n 3 is measured by the bicoherency. In the RFP, m=l, n∼2R/a (6 for MST) internally resonant modes are linearly unstable and grow to large amplitude. Large values of bicoherency occur for two m=l modes coupled to an m=2 mode and the coupling of intermediate toroidal modes, e.g., n=6 and 7 coupled to n=13. These experimental bispectral features agree with predicted bispectral features derived from MHD computation. However, in the experiment, enhanced coupling occurs in the ''crash'' phase of a sawtooth oscillation concomitant with a broadened mode spectrum suggesting the onset of a nonlinear cascade
Thomson scattering on ELMO Bumpy Torus
International Nuclear Information System (INIS)
Cobble, J.A.
1985-04-01
Below 10 12 cm -3 density, a Thomson scattering experiment is an exacting task. Aside from the low signal level, the core plasma in this instance is bathed in high-energy x rays, surrounded by a glowing molecular surface plasma, and heated steady state by microwaves. This means that the noise level from radiation is high and the environment is extremely harsh-so harsh that much effort is required to overcome system damage. In spite of this, the ELMO Bumpy Torus (EBT) system has proven itself capable of providing reliable n/sub e/ and T/sub e/ measurements at densities as low as 2 x 10 11 cm -3 . Radial scans across 20 cm of the plasma diameter have been obtained on a routine basis, and the resulting information has been a great help in understanding confinement in the EBT plasma. The bulk electron properties are revealed as flat profiles of n/sub e/ and T/sub e/, with density ranging from 0.5 to 2.0 x 10 12 cm -3 and temperature decreasing from 100 to 20 eV as pressure in the discharge is increased at constant power. Evidence is presented for a suprathermal tail, which amounts to about 10% of the electron distribution at low pressures. The validity of this conclusion is supported by two independent sensitivity calibrations
Hirzebruch genera of manifolds with torus action
International Nuclear Information System (INIS)
Panov, T E
2001-01-01
A quasitoric manifold is a smooth 2n-manifold M 2n with an action of the compact torus T n such that the action is locally isomorphic to the standard action of T n on C n and the orbit space is diffeomorphic, as a manifold with corners, to a simple polytope P n . The name refers to the fact that topological and combinatorial properties of quasitoric manifolds are similar to those of non-singular algebraic toric varieties (or toric manifolds). Unlike toric varieties, quasitoric manifolds may fail to be complex. However, they always admit a stably (or weakly almost) complex structure, and their cobordism classes generate the complex cobordism ring. Buchstaber and Ray have recently shown that the stably complex structure on a quasitoric manifold is determined in purely combinatorial terms, namely, by an orientation of the polytope and a function from the set of codimension-one faces of the polytope to primitive vectors of the integer lattice. We calculate the χ y -genus of a quasitoric manifold with a fixed stably complex structure in terms of the corresponding combinatorial data. In particular, this gives explicit formulae for the classical Todd genus and the signature. We also compare our results with well-known facts in the theory of toric varieties
ADHM construction of instantons on the torus
International Nuclear Information System (INIS)
Ford, C.; Pawlowski, J.M.; Tok, T.; Wipf, A.
2001-01-01
We apply the ADHM instanton construction to SU(2) gauge theory on T n xR 4-n for n=1,2,3,4. To do this we regard instantons on T n xR 4-n as periodic (modulo gauge transformations) instantons on R 4 . Since the R 4 topological charge of such instantons is infinite the ADHM algebra takes place on an infinite dimensional linear space. The ADHM matrix M is related to a Weyl operator (with a self-dual background) on the dual torus T-tilde n . We construct the Weyl operator corresponding to the one-instantons on T n xR 4-n . In order to derive the self-dual potential on T n xR 4-n it is necessary to solve a specific Weyl equation. This is a variant of the Nahm transformation. In the case n=2 (i.e., T 2 xR 2 ) we essentially have an Aharonov-Bohm problem on T-tilde 2 . In the one-instanton sector we find that the scale parameter, λ, is bounded above, λ 2 V-tilde 2
How fast does a random walk cover a torus?
Grassberger, Peter
2017-07-01
We present high statistics simulation data for the average time that a random walk needs to cover completely a two-dimensional torus of size L ×L . They confirm the mathematical prediction that ˜(LlnL ) 2 for large L , but the prefactor seems to deviate significantly from the supposedly exact result 4 /π derived by Dembo et al. [Ann. Math. 160, 433 (2004), 10.4007/annals.2004.160.433], if the most straightforward extrapolation is used. On the other hand, we find that this scaling does hold for the time TN (t )=1(L ) at which the average number of yet unvisited sites is 1, as also predicted previously. This might suggest (wrongly) that and TN (t )=1(L ) scale differently, although the distribution of rescaled cover times becomes sharp in the limit L →∞ . But our results can be reconciled with those of Dembo et al. by a very slow and nonmonotonic convergence of /(LlnL ) 2 , as had been indeed proven by Belius et al. [Probab. Theory Relat. Fields 167, 461 (2017), 10.1007/s00440-015-0689-6] for Brownian walks, and was conjectured by them to hold also for lattice walks.
Hamiltonian theory of vacuum helical torus lines of magnetic force
International Nuclear Information System (INIS)
Gnudi, Giovanni; Hatori, Tadatsugu
1994-01-01
For making plasma into equilibrium state, the lines of magnetic force must have magnetic surfaces. However in a helical system, space is divided into the region having magnetic surface structure and the region that does not have it. Accordingly, it is an important basic research for the plasma confinement in a helical system to examine where is the boundary of both regions and how is the large area structure of the lines of magnetic force in the boundary region. The lines of magnetic force can be treated as a Hamilton mechanics system, and it has been proved that the Hamiltonian for the lines of magnetic force can be expressed by a set of canonical variables and the function of time. In this research, the Hamiltonian that describes the lines of magnetic force of helical system torus coordination in vacuum was successfully determined concretely. Next, the development of new linear symplectic integration method was carried out. The important supports for the theory of determining Hamiltonian are Lie transformation and paraxial expansion. The procedure is explained. In Appendix, Lie transformation, Hamiltonian for the lines of magnetic force, magnetic potential, Taylor expansion of the potential, cylindrical limit approximation, helical toroidal potential and integrable model are described. (K.I.)
Design innovations of the next-step spherical torus experiment and spherical torus development path
International Nuclear Information System (INIS)
Ono, M.; Kessel, C.; Peng, M.
2003-01-01
The spherical torus (ST) fusion energy development path is complementary to the tokamak burning plasma experiment such as ITER as it focuses toward the compact Component Test Facility (CTF) and higher toroidal beta regimes to improve the design of DEMO and a Power Plant. To support the ST development path, one option of a Next Step Spherical Torus (NSST) device is examined. NSST is a 'performance extension' (PE) stage ST with a plasma current of 5 - 10 MA, R = 1.5, B T ≤ 2.7 T with flexible physics capability to 1) Provide a sufficient physics basis for the design of the CTF, 2) Explore advanced operating scenarios with high bootstrap current fraction/high performance regimes, which can then be utilized by CTF, DEMO, and Power Plants, 3) Contribute to the general plasma/fusion science of high β toroidal plasmas. The NSST facility is designed to utilize the TFTR site to minimize the cost and time required for the construction. (author)
International Nuclear Information System (INIS)
Ono, M.; Peng, M.; Kessel, C.; Neumeyer, C.; Schmidt, J.; Chrzanowski, J.; Darrow, D.; Grisham, L.; Heitzenroeder, P.; Jarboe, T.; Jun, C.; Kaye, S.; Menard, J.; Raman, R.; Stevenson, T.; Viola, M.; Wilson, J.; Woolley, R.; Zatz, I.
2003-01-01
A spherical torus (ST) fusion energy development path which is complementary to proposed tokamak burning plasma experiments such as ITER is described. The ST strategy focuses on a compact Component Test Facility (CTF) and higher performance advanced regimes leading to more attractive DEMO and Power Plant scale reactors. To provide the physics basis for the CTF an intermediate step needs to be taken which we refer to as the ''Next Step Spherical Torus'' (NSST) device and examine in some detail herein. NSST is a ''performance extension'' (PE) stage ST with the plasma current of 5-10 MA, R = 1.5 m, and Beta(sub)T less than or equal to 2.7 T with flexible physics capability. The mission of NSST is to: (1) provide a sufficient physics basis for the design of CTF, (2) explore advanced operating scenarios with high bootstrap current fraction/high performance regimes, which can then be utilized by CTF, DEMO, and Power Plants, and (3) contribute to the general plasma/fusion science of high beta toroidal plasmas. The NSST facility is designed to utilize the Tokamak Fusion Test Reactor (or similar) site to minimize the cost and time required for the design and construction
Spectra of germanium and selenium in the 50-350 A region from the PLT tokamak plasma
International Nuclear Information System (INIS)
Stratton, B.C.; Hodge, W.L.; Moos, H.W.; Schwob, J.L.; Suckewer, S.; Finkenthal, M.; Cohen, S.
1983-03-01
Spectra of germanium and selenium injected into the PLT tokamak plasma were observed in the 50 to 350 A region for GeXIV-XXV (KI to OI-like) and SeXVI-XXIV (KI to NaI-like). A number of 3p/sup k/-3p/sup k-1/3d transitions predicted by isoelectronic sequence extrapolation have been identified. Also, previously identified lines from ions in the AlI to OI-like and KI-like isoelectronic sequences have been observed in the tokamak plasma
International Nuclear Information System (INIS)
Skinner, C.H.; Suckewer, S.; Cohen, S.A.; Schilling, G.; Wilson, R.; Stratton, B.
1984-03-01
We report the first observation of line emission resulting directly from charge-exchange recombination of medium-Z elements (Al, Sc) injected into a PLT discharge. Transitions due to the radiative cascade immediately following charge-exchange of He-like Al and Sc were observed by a VUV spectrograph and two air monochromators. In two cases, AlXI 3209 A and ScXIX 112.1 A, the observed transition had not previously been experimentally identified. Spatial scans provided information on the profile of the neutral beam in the plasma
Directory of Open Access Journals (Sweden)
Usman Ali Gulzari
Full Text Available A Mesh topology is one of the most promising architecture due to its regular and simple structure for on-chip communication. Performance of mesh topology degraded greatly by increasing the network size due to small bisection width and large network diameter. In order to overcome this limitation, many researchers presented modified Mesh design by adding some extra links to improve its performance in terms of network latency and power consumption. The Cross-By-Pass-Mesh was presented by us as an improved version of Mesh topology by intelligent addition of extra links. This paper presents an efficient topology named Cross-By-Pass-Torus for further increase in the performance of the Cross-By-Pass-Mesh topology. The proposed design merges the best features of the Cross-By-Pass-Mesh and Torus, to reduce the network diameter, minimize the average number of hops between nodes, increase the bisection width and to enhance the overall performance of the network. In this paper, the architectural design of the topology is presented and analyzed against similar kind of 2D topologies in terms of average latency, throughput and power consumption. In order to certify the actual behavior of proposed topology, the synthetic traffic trace and five different real embedded application workloads are applied to the proposed as well as other competitor network topologies. The simulation results indicate that Cross-By-Pass-Torus is an efficient candidate among its predecessor's and competitor topologies due to its less average latency and increased throughput at a slight cost in network power and energy for on-chip communication.
TFTR centralized torus interface valve control system
International Nuclear Information System (INIS)
Pearson, G.G.; Olsen, D.H.
1983-01-01
A system developed especially for the TFTR to monitor and control the interface between the vacuum vessel and associated diagnostics will be described in this paper. Diagnostics which must be connected to the machine vacuum are required to do so through a Torus Interface Valve (TIV). Two types of TIV's are used on TFTR. The first type is a non-latching valve which must be held in the opened position by a sustained OPEN command, returning automatically to the closed position when the OPEN command is removed. This type of TIV is used on all systems which never insert a probe into the vacuum vessel through the TIV. The second type of TIV is a latching valve which requires a momentary OPEN command to open and a momentary CLOSE command to close. Each TIV is linked to its own dedicated logic controller. Each logic controller is hardwired to the appropriate TIV OPEN/CLOSED limit switches, probe IN/OUT limit switches, TFTR vacuum vessel pressure setpoint switches, and diagnostic pressure setpoint switches. The logic controller can be configured for local (push-button) or remote (computer) control. Each controller has a uniquely coded keyswitch to determine the configuration. Whether under local or remote control, all OPEN and CLOSE commands must be approved by the TIV controller (TIVC). In the case of systems with probes, the controller must receive a positive indication that the probe is completely backed out before a CLOSE command will be transmitted from the TIVC to the TIV. Before a valve will be opened by a controller, the differential pressure across the valve must be within certain limits
International Nuclear Information System (INIS)
Bondarenko, Vladimir E.; Cymbalyuk, Gennady S.; Patel, Girish; DeWeerth, Stephen P.; Calabrese, Ronald L.
2004-01-01
Oscillatory activity in the central nervous system is associated with various functions, like motor control, memory formation, binding, and attention. Quasiperiodic oscillations are rarely discussed in the neurophysiological literature yet they may play a role in the nervous system both during normal function and disease. Here we use a physical system and a model to explore scenarios for how quasiperiodic oscillations might arise in neuronal networks. An oscillatory system of two mutually inhibitory neuronal units is a ubiquitous network module found in nervous systems and is called a half-center oscillator. Previously we created a half-center oscillator of two identical oscillatory silicon (analog Very Large Scale Integration) neurons and developed a mathematical model describing its dynamics. In the mathematical model, we have shown that an in-phase limit cycle becomes unstable through a subcritical torus bifurcation. However, the existence of this torus bifurcation in experimental silicon two-neuron system was not rigorously demonstrated or investigated. Here we demonstrate the torus predicted by the model for the silicon implementation of a half-center oscillator using complex time series analysis, including bifurcation diagrams, mapping techniques, correlation functions, amplitude spectra, and correlation dimensions, and we investigate how the properties of the quasiperiodic oscillations depend on the strengths of coupling between the silicon neurons. The potential advantages and disadvantages of quasiperiodic oscillations (torus) for biological neural systems and artificial neural networks are discussed
Partially collisional model of the Titan hydrogen torus
International Nuclear Information System (INIS)
Hilton, D.A.
1987-01-01
A numerical model was developed for atomic hydrogen densities in the Titan hydrogen torus. The effects of occasional collisions were included in order to accurately simulate physical conditions inferred from the Voyager 1 and 2 Ultraviolet Spectrometer (UVS) results of Broadfoot et al. (1981) and Sandel et al. (1982). The model employed Lagrangian perturbation of orbital elements of hydrogen atoms launched from Titan and Monte Carlo simulation of collisions and loss mechanisms. The torus is found to be azimuthally symmetric with the density sharply peaked at Titan's orbit, and decreasing rapidly in the outward and perpendicular directions and more gradually inward from 17 to 5 R/sub s/. The energetic hydrogen atoms from Saturn's upper atmosphere, first predicted by Shemansky and Smith (1982), were also investigated. Collisions of these Saturnian atoms with the torus population do not contribute to the torus density, and will lead to a net loss of torus atoms if their launch speeds from Saturn extend above 40 km/sec. The Saturnian atoms produce a corona which was modeled using the theory of Chamberlain (1963)
Smooth invariant densities for random switching on the torus
Bakhtin, Yuri; Hurth, Tobias; Lawley, Sean D.; Mattingly, Jonathan C.
2018-04-01
We consider a random dynamical system obtained by switching between the flows generated by two smooth vector fields on the 2d-torus, with the random switchings happening according to a Poisson process. Assuming that the driving vector fields are transversal to each other at all points of the torus and that each of them allows for a smooth invariant density and no periodic orbits, we prove that the switched system also has a smooth invariant density, for every switching rate. Our approach is based on an integration by parts formula inspired by techniques from Malliavin calculus.
The CLAS12 Torus Detector Magnet at Jefferson Laboratory
Energy Technology Data Exchange (ETDEWEB)
Luongo, Cesar [Jefferson Lab; Ballard, Joshua [Jefferson Lab; Biallas, George [Jefferson Lab; Elouadrhiri, Latifa [Jefferson Lab; Fair, Ruben [Jefferson Lab; Ghoshal, Probir [Jefferson Lab; Kashy, Dave [Jefferson Lab; Legg, Robert [Jefferson Lab; Pastor, Orlando [Jefferson Lab; Rajput-Ghoshal, Renuka [Jefferson Lab; Rode, Claus [Jefferson Lab; Wiseman, Mark [Jefferson Lab; Young, Glenn [Jefferson Lab; Elementi, Luciano [Fermilab; Krave, Steven [Fermilab; Makarov, Alexander [Fermilab; Nobrega, Fred [Fermilab; Velev, George [Fermilab
2015-12-17
The CLAS12 Torus is a toroidal superconducting magnet, which is part of the detector for the 12-GeV accelerator upgrade at Jefferson Laboratory (JLab). The coils were wound/fabricated by Fermilab, with JLab responsible for all other parts of the project scope, including design, integration, cryostating the individual coils, installation, cryogenics, I&C, etc. This paper provides an overview of the CLAS12 Torus magnet features and serves as a status report of its installation in the experimental hall. Completion and commissioning of the magnet is expected in 2016.
Maass Cusp Forms on Singly Punctured Two-Torus
International Nuclear Information System (INIS)
Siddig, Abubaker Ahmed Mohamed; Shah, Nurisya Mohd; Zainuddin, Hishamuddin
2009-01-01
Quantum mechanical systems on punctured surfaces modeled by hyperbolic spaces can play an interesting role in exploring quantum chaos and in studying behaviour of future quantum nano-devices. The case of singly-punctured two-torus, for example, has been well-studied in the literature particularly for its scattering states. However, the bound states on the punctured torus given by Maass cusp forms are lesser known. In this note, we report on the algorithm of numerically computing these functions and we present ten lower-lying eigenvalues for each odd and even Maass cusp forms.
Quasiperiodicity and Torus Breakdown in a Power Electronic DC/DC Converter
DEFF Research Database (Denmark)
Zhusubaliyev, Zhanybai; Soukhoterin, Evgeniy; Mosekilde, Erik
2007-01-01
This paper discusses the mechanisms of torus formation and torus destruction in a dc/dc converter with relay control and hysteresis. We establish a chart of the dynamical modes in the input voltage versus load resistance parameter plane. This chart displays several different torus bifurcations...
Legendrian and transverse cables of positive torus knots
DEFF Research Database (Denmark)
B. Etnyre, John; la Fountain, Douglas James; Tosun, Bulent
In this paper we classify Legendrian and transverse knots in the knot types obtained from positive torus knots by cabling. This classification allows us to demonstrate several new phenomena. Specifically, we show there are knot types that have non-destabilizable Legendrian representatives whose T...
Beta II compact torus experiment plasma equilibrium and power balance
International Nuclear Information System (INIS)
Turner, W.C.; Goldenbaum, G.C.; Granneman, E.H.A.; Prono, D.S.; Hartman, C.W.; Taska, J.
1982-01-01
In this paper we follow up some of our earlier work that showed the compact torus (CT) plasma equilibrium produced by a magnetized coaxial plasma gun is nearly force free and that impurity radiation plays a dominant role in determining the decay time of plasma currents in present generation experiments
Recursive representation of the torus 1-point conformal block
Hadasz, Leszek; Jaskólski, Zbigniew; Suchanek, Paulina
2010-01-01
The recursive relation for the 1-point conformal block on a torus is derived and used to prove the identities between conformal blocks recently conjectured by Poghossian in [1]. As an illustration of the efficiency of the recurrence method the modular invariance of the 1-point Liouville correlation function is numerically analyzed.
Global solvability for involutive systems on the torus
Directory of Open Access Journals (Sweden)
Cleber de Medeira
2013-11-01
Full Text Available In this article, we consider a class of involutive systems of n smooth vector fields on the torus of dimension n+1. We prove that the global solvability of this class is related to an algebraic condition involving Liouville forms and the connectedness of all sublevel and superlevel sets of the primitive of a certain 1-form associated with the system.
Atomic force microscopy of torus-bearing pit membranes
Roland R. Dute; Thomas Elder
2011-01-01
Atomic force microscopy was used to compare the structures of dried, torus-bearing pit membranes from four woody species, three angiosperms and one gymnosperm. Tori of Osmanthus armatus are bipartite consisting of a pustular zone overlying parallel sets of microfibrils that form a peripheral corona. Microfibrils of the corona form radial spokes as they traverse the...
Modular differential equations for torus one-point functions
International Nuclear Information System (INIS)
Gaberdiel, Matthias R; Lang, Samuel
2009-01-01
It is shown that in a rational conformal field theory every torus one-point function of a given highest weight state satisfies a modular differential equation. We derive and solve these differential equations explicitly for some Virasoro minimal models. In general, however, the resulting amplitudes do not seem to be expressible in terms of standard transcendental functions
Spherical torus (ST) concept and its reactor implications
International Nuclear Information System (INIS)
Peng, Y.K.M.; Lazarus, E.A.; Miller, R.L.; Carreras, B.A.; Hogan, J.T.; Krakowski, R.A.; Seed, T.J.; Zubrin, R.M.; Schnurr, N.M.
1986-01-01
A brief description of the spherical torus design is given. The design concept includes resistive demountable toroidal field coils, poloidal divertor for impurity control, oscillating-field current maintenance, RF initiation and ramp-up of the plasma current, and flowing liquid-metal breeding blanket. 4 refs., 6 figs
Five-dimensional gauge theory and compactification on a torus
Haghighat, B.; Vandoren, S.J.G.
2011-01-01
We study five-dimensional minimally supersymmetric gauge theory compactified on a torus down to three dimensions, and its embedding into string/M-theory using geometric engineering. The moduli space on the Coulomb branch is hyperkaehler equipped with a metric with modular transformation properties.
Plasma diagnostics in compact torus of UNICAMP (Campinas state university)
International Nuclear Information System (INIS)
Ueda, M; Doi, Y.; Aramaki, E.A.; Porto, P.; Berni, L.; Machida, M.
1989-08-01
This paper which describes experiments carried out in the Compact Torus of UNICAMP (TC-1) is divided into 3 parts: 1) summary of TC-1 characteristics and its operation mode; 2) description of diagnostics in use and ones to be installed, 3) recent experimental results using optical and electromagnetical diagnostics. (author)
ELMO Bumpy Torus fusion-reactor design study
International Nuclear Information System (INIS)
Bathke, C.G.; Krakowski, R.A.
1981-01-01
A complete power plant design of a 1200-MWe ELMO Bumpy Torus Reactor (EBTR) is described that emphasizes those features that are unique to the EBT confinement concept, with subsystems and balance-of-plant items that are generic to magnetic fusion being adopted from past, more extensive tokamak reactor designs
Nonlinear evolution of magnetic islands in a two fluid torus
International Nuclear Information System (INIS)
Sugiyama, L.E.; Park, W.
1996-01-01
A numerical model MH3D-T for the two fluid description of macroscopic evolution in a full three dimensional torus has been developed. Based on the perturbative drift ordering, generalized to arbitrary perturbation size, the model follows the full temperature evolution, including the thermal equilibration along the magnetic field. It contains the diamagnetic drifts, ion gyroviscous stress tensor, and the Hall term in Ohm's law. Electron inertia is neglected. The numerical model solves the same equations in a torus and in several simplified configurations. It has been benchmarked against the diamagnetic ω* i stabilization of the resistive m = 1, n = 1 reconnecting mode in a cylinder. The nonlinear evolution of resistive magnetic islands with m,n ≠ 1,1 in a cylinder is found to agree with previous analytic and reduced-torus results, which show that the diamagnetic rotation vanishes early in the island evolution and the saturated island size is determined by the same external driving factor Δ' as in MHD. The two fluid evolution in a full torus, however, differs from that in a cylinder and from the resistive MHD evolution. The poloidal rotation velocity undergoes a degree of poloidal momentum damping in the torus, even without neoclassical effects. The two fluid magnetic island grows faster, nonlinearly, than the resistive MHD island, and also couples different toroidal harmonics more effectively. Plasma compressibility and processes operating along the magnetic field play a much more important role than in MHD or in simple geometry. The two fluid model contains all the important neoclassical fluid effects except for the b circ ∇ circ Π parallelj viscous force terms. The addition of these terms is in progress
Energy Technology Data Exchange (ETDEWEB)
Gabriel, T.; Litz, L. [Technische Univ. Kaiserslautern (Germany); Schroers, B. [Material-Science AG, Leverkusen (Germany)
2008-01-15
According to the standard IEC 61511 each safety-related loop is assigned to one of the four Safety Integrity Levels (SILs). For every safety-related loop a SIL-specific Probability of Failure on Demand (PFD) must be proven. Usually, the PFD calculation is performed based upon the failure rates of each loop component aided by commercial software tools. However, this bottom-up approach suffers from many uncertainties. Especially, a lack of reliable failure rate data causes many problems. Reference data collected in different environments are available to solve this situation. However, this pragmatism leads to a PFD bandwidth, not to a single PFD value as desired. In order to make a decision for a numerical value appropriate for the chemical and pharmaceutical process industry a data ascertainment has been initiated by the European NAMUR. Its results display large deficiencies for the bottom-up approach. The error sources leading to this situation are located and analyzed. (GL)
Souza, J.T.; Raaijmakers, J.M.
2003-01-01
Pyrrolnitrin (PRN) and pyoluteorin (PLT) are broad-spectrum antibiotics produced by several strains of Pseudomonas and Burkholderia species. Both antibiotics play an important role in the suppression of multiple plant pathogenic fungi. Primers were developed from conserved sequences and amplified
Exploration of spherical torus physics in the NSTX device
Ono, M.; Kaye, S. M.; Peng, Y.-K. M.; Barnes, G.; Blanchard, W.; Carter, M. D.; Chrzanowski, J.; Dudek, L.; Ewig, R.; Gates, D.; Hatcher, R. E.; Jarboe, T.; Jardin, S. C.; Johnson, D.; Kaita, R.; Kalish, M.; Kessel, C. E.; Kugel, H. W.; Maingi, R.; Majeski, R.; Manickam, J.; McCormack, B.; Menard, J.; Mueller, D.; Nelson, B. A.; Nelson, B. E.; Neumeyer, C.; Oliaro, G.; Paoletti, F.; Parsells, R.; Perry, E.; Pomphrey, N.; Ramakrishnan, S.; Raman, R.; Rewoldt, G.; Robinson, J.; Roquemore, A. L.; Ryan, P.; Sabbagh, S.; Swain, D.; Synakowski, E. J.; Viola, M.; Williams, M.; Wilson, J. R.; NSTX Team
2000-03-01
The National Spherical Torus Experiment (NSTX) is being built at Princeton Plasma Physics Laboratory to test the fusion physics principles for the spherical torus concept at the MA level. The NSTX nominal plasma parameters are R0 = 85 cm, a = 67 cm, R/a >= 1.26, Bt = 3 kG, Ip = 1 MA, q95 = 14, elongation κ The plasma heating/current drive tools are high harmonic fast wave (6 MW, 5 s), neutral beam injection (5 MW, 80 keV, 5 s) and coaxial helicity injection. Theoretical calculations predict that NSTX should provide exciting possibilities for exploring a number of important new physics regimes, including very high plasma β, naturally high plasma elongation, high bootstrap current fraction, absolute magnetic well and high pressure driven sheared flow. In addition, the NSTX programme plans to explore fully non-inductive plasma startup as well as a dispersive scrape-off layer for heat and particle flux handling.
Five-dimensional gauge theory and compactification on a torus
Haghighat, Babak; Vandoren, Stefan
2011-09-01
We study five-dimensional minimally supersymmetric gauge theory compactified on a torus down to three dimensions, and its embedding into string/M-theory using geometric engineering. The moduli space on the Coulomb branch is hyperkähler equipped with a metric with modular transformation properties. We determine the one-loop corrections to the metric and show that they can be interpreted as worldsheet and D1-brane instantons in type IIB string theory. Furthermore, we analyze instanton corrections coming from the solitonic BPS magnetic string wrapped over the torus. In particular, we show how to compute the path-integral for the zero-modes from the partition function of the M5 brane, or, using a 2d/4d correspondence, from the partition function of N=4 SYM theory on a Hirzebruch surface.
Recent results from the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Maingi, R; Bell, M G; Bell, R E; Bialek, J; Bourdelle, C; Bush, C E; Darrow, D S; Fredrickson, E D; Gates, D A; Gilmore, M; Gray, T; Jarboe, T R; Johnson, D W; Kaita, R; Kaye, S M; Kubota, S; Kugel, H W; LeBlanc, B P; Maqueda, R J; Mastrovito, D; Medley, S S; Menard, J E; Mueller, D; Nelson, B A; Ono, M; Paoletti, F; Park, H K; Paul, S F; Peebles, T; Peng, Y-K M; Phillips, C K; Raman, R; Rosenberg, A L; Roquemore, A L; Ryan, P M; Sabbagh, S A; Skinner, C H; Soukhanovskii, V A; Stutman, D; Swain, D W; Synakowski, E J; Taylor, G; Wilgen, J; Wilson, J R; Wurden, G A; Zweben, S J
2003-01-01
The National Spherical Torus Experiment (NSTX) is a low aspect-ratio fusion research facility whose research goal is to make a determination of the attractiveness of the spherical torus concept in the areas of high-β stability, confinement, current drive, and divertor physics. Remarkable progress was made in extending the operational regime of the device in FY 2002. In brief, β t of 34% and β N of 6.5 were achieved. H-mode became the main operational regime, and energy confinement exceeded conventional aspect-ratio tokamak scalings. Heating was demonstrated with the radiofrequency antenna, and signatures of current drive were observed. Current initiation with coaxial helicity injection produced discharges of 400 kA, and first measurements of divertor heat flux profiles in H-mode were made
TORUS: Theory of Reactions for Unstable iSotopes - Year 1 Continuation and Progress Report
Energy Technology Data Exchange (ETDEWEB)
Arbanas, G; Elster, C; Escher, J; Mukhamedzhanov, A; Nunes, F; Thompson, I J
2011-02-24
The TORUS collaboration derives its name from the research it focuses on, namely the Theory of Reactions for Unstable iSotopes. It is a Topical Collaboration in Nuclear Theory, and funded by the Nuclear Theory Division of the Office of Nuclear Physics in the Office of Science of the Department of Energy. The funding started on June 1, 2010, it will have been running for nine months by the date of submission of this Annual Continuation and Progress Report on March 1, 2011. The extent of funding was reduced from the original application, and now supports one postdoctoral researcher for the years 1 through 3. The collaboration brings together as Principal Investigators a large fraction of the nuclear reaction theorists currently active within the USA. The mission of the TORUS Topical Collaboration is to develop new methods that will advance nuclear reaction theory for unstable isotopes by using three-body techniques to improve direct-reaction calculations, and, by using a new partial-fusion theory, to integrate descriptions of direct and compound-nucleus reactions. This multi-institution collaborative effort is directly relevant to three areas of interest: the properties of nuclei far from stability; microscopic studies of nuclear input parameters for astrophysics, and microscopic nuclear reaction theory.
Calculations of Neutral Beam Ion Confinement for the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Redi, M.H.; Darrow, D.S.; Egedal, J.; Kaye, S.M.; White, R.B.
2002-01-01
The spherical torus (ST) concept underlies several contemporary plasma physics experiments, in which relatively low magnetic fields, high plasma edge q, and low aspect ratio combine for potentially compact, high beta and high performance fusion reactors. An important issue for the ST is the calculation of energetic ion confinement, as large Larmor radius makes conventional guiding center codes of limited usefulness and efficient plasma heating by RF and neutral beam ion technology requires minimal fast ion losses. The National Spherical Torus Experiment (NSTX) is a medium-sized, low aspect ratio ST, with R=0.85 m, a=0.67 m, R/a=1.26, Ip*1.4 MA, Bt*0.6 T, 5 MW of neutral beam heating and 6 MW of RF heating. 80 keV neutral beam ions at tangency radii of 0.5, 0.6 and 0.7 m are routinely used to achieve plasma betas above 30%. Transport analyses for experiments on NSTX often exhibit a puzzling ion power balance. It will be necessary to have reliable beam ion calculations to distinguish among the source and loss channels, and to explore the possibilities for new physics phenomena, such as the recently proposed compressional Alfven eigenmode ion heating
Exploration of high harmonic fast wave heating on the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Wilson, J.R.; Bell, R.E.; Bernabei, S.; Bitter, M.; Gates, D.; Hosea, J.; Le Blanc, B.; Medley, S.; Menard, J.; Mueller, D.; Ono, M.; Phillips, C.K.; Rosenberg, A.; Bonoli, P.; Mau, T.K.; Pinsker, R.I.; Raman, R.; Ryan, P.; Swain, D.; Wilgen, J.
2003-01-01
High harmonic fast wave (HHFW) heating has been proposed as a particularly attractive means for plasma heating and current drive in the high beta plasmas that are achievable in spherical torus (ST) devices. The National Spherical Torus Experiment (NSTX) [M. Ono, S. M. Kaye, S. Neumeyer et al., in Proceedings of the 18th IEEE/NPSS Symposium on Fusion Engineering, Albuquerque, 1999 (IEEE, Piscataway, NJ, 1999), p. 53] is such a device. An rf heating system has been installed on the NSTX to explore the physics of HHFW heating, current drive via rf waves and for use as a tool to demonstrate the attractiveness of the ST concept as a fusion device. To date, experiments have demonstrated many of the theoretical predictions for HHFW. In particular, strong wave absorption on electrons over a wide range of plasma parameters and wave parallel phase velocities, wave acceleration of energetic ions, and indications of current drive for directed wave spectra have been observed. In addition HHFW heating has been used to explore the energy transport properties of NSTX plasmas, to create H-mode discharges with a large fraction of bootstrap current and to control the plasma current profile during the early stages of the discharge
Exploration of High Harmonic Fast Wave Heating on the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Wilson, J.R.; Bell, R.E.; Bernabei, S.; Bitter, M.; Bonoli, P.; Gates, D.; Hosea, J.; LeBlanc, B.; Mau, T.K.; Medley, S.; Menard, J.; Mueller, D.; Ono, M.; Phillips, C.K.; Pinsker, R.I.; Raman, R.; Rosenberg, A.; Ryan, P.; Sabbagh, S.; Stutman, D.; Swain, D.; Takase, Y.; Wilgen, J.
2003-01-01
High Harmonic Fast Wave (HHFW) heating has been proposed as a particularly attractive means for plasma heating and current drive in the high-beta plasmas that are achievable in spherical torus (ST) devices. The National Spherical Torus Experiment (NSTX) [Ono, M., Kaye, S.M., Neumeyer, S., et al., Proceedings, 18th IEEE/NPSS Symposium on Fusion Engineering, Albuquerque, 1999, (IEEE, Piscataway, NJ (1999), p. 53.)] is such a device. An radio-frequency (rf) heating system has been installed on NSTX to explore the physics of HHFW heating, current drive via rf waves and for use as a tool to demonstrate the attractiveness of the ST concept as a fusion device. To date, experiments have demonstrated many of the theoretical predictions for HHFW. In particular, strong wave absorption on electrons over a wide range of plasma parameters and wave parallel phase velocities, wave acceleration of energetic ions, and indications of current drive for directed wave spectra have been observed. In addition HHFW heating has been used to explore the energy transport properties of NSTX plasmas, to create H-mode (high-confinement mode) discharges with a large fraction of bootstrap current and to control the plasma current profile during the early stages of the discharge
Thickness mapping of submerged portions of a BWR torus using an ROV
International Nuclear Information System (INIS)
Somers, T.; Bagley, J.G.
1992-01-01
A methodology has been developed for establishing an ultrasonic baseline of the submerged portions of a boiling water reactor torus shell. A remotely operated vehicle (ROV) is equipped to deliver an array of ultrasonic thickness transducers to within a fixed stand-off from the shell. The position of the transducers at each ultrasound reading is measured and recorded using a precision acoustic navigation system. The resulting thickness contour map makes it possible to visualize the condition of the torus shell and provides quantitative documentation of shell thickness at a large number of known locations. The navigation system can be reinstalled in the future so that by comparing future thickness readings acquired at the same location, it is possible to create a map of the rate of change in shell thickness. An ultrasonic thickness survey was conducted recently using a preliminary version of such a system. The experience gained in performing this survey has been incorporated in the design of a full-scale prototype system, which is currently under development. This system will include such features as automatic control of the ROV based on the acoustic navigation data, generation of three-dimensional thickness maps, and remote control of the data acquisition process from outside the radiation area
Matrix factorizations and homological mirror symmetry on the torus
International Nuclear Information System (INIS)
Knapp, Johanna; Omer, Harun
2007-01-01
We consider matrix factorizations and homological mirror symmetry on the torus T 2 using a Landau-Ginzburg description. We identify the basic matrix factorizations of the Landau-Ginzburg superpotential and compute the full spectrum taking into account the explicit dependence on bulk and boundary moduli. We verify homological mirror symmetry by comparing three-point functions in the A-model and the B-model
Perturbative construction of self-dual configurations on the torus
International Nuclear Information System (INIS)
Garcia Perez, M.; Gonzalez-Arroyo, A.; Pena, C.
2000-01-01
We develop a perturbative expansion which allows the construction of non-abelian self-dual SU(2) Yang-Mills field configurations on the four-dimensional torus with topological charge 1/2. The expansion is performed around the constant field strength abelian solutions found by 't Hooft. Next to leading order calculations are compared with numerical results obtained with lattice gauge theory techniques. (author)
Recent results in the Los Alamos compact torus program
International Nuclear Information System (INIS)
Tuszewski, M.; Armstrong, W.T.; Barnes, C.W.
1983-01-01
A Compact Toroid is a toroidal magnetic-plasma-containment geometry in which no conductors or vacuum-chamber walls pass through the hole in the torus. Two types of compact toroids are studied experimentally and theoretically at Los Alamos: spheromaks that are oblate in shape and contain both toroidal and poloidal magnetic fields, and field-reversed configurations (FRC) that are very prolate and contain poloidal field only
High energy density fusing using the Compact Torus
International Nuclear Information System (INIS)
Hartman, C.W.
1989-01-01
My remarks are concerned with employing the Compact Torus magnetic field configuration to produce fusion energy. In particular, I would like to consider high energy density regimes where the pressures generated extend well beyond the strength of materials. Under such conditions, where nearby walls are vaporized and pushed aside each shot, the technological constraints are very different from usual magnetic fusion and may admit opportunities for an improved fusion reactor design. 5 refs., 3 figs
Development of concentric equipotential surfaces in bumpy torus plasma
International Nuclear Information System (INIS)
Takasugi, Keiichi; Iguchi, Harukazu; Fujiwara, Masami; Ikegami, Hideo
1983-01-01
Radial profiles of the plasma space potential are measured in Nagoya Bumpy Torus (NBT-1) by the use of a heavy ion beam probe. Asymmetric potential profiles owing to toroidal drift are observed in high pressure operation (C-mode). As the pressure is decreased, toroidal plasma is effectively heated (T-mode), poloidal precessional frequency overcomes the electron collision frequency and the equipotential surfaces becomes concentric inside the hot electron ring. (author)
Electromagnetic diagnostic system for the Keda Torus eXperiment
Tu, Cui; Liu, Adi; Li, Zichao; Tan, Mingsheng; Luo, Bing; You, Wei; Li, Chenguang; Bai, Wei; Fu, Chenshuo; Huang, Fangcheng; Xiao, Bingjia; Shen, Biao; Shi, Tonghui; Chen, Dalong; Mao, Wenzhe; Li, Hong; Xie, Jinglin; Lan, Tao; Ding, Weixing; Xiao, Chijin; Liu, Wandong
2017-09-01
A system for electromagnetic measurements was designed and installed on the Keda Torus eXperiment (KTX) reversed field pinch device last year. Although the unique double-C structure of the KTX, which allows the machine to be opened easily without disassembling the poloidal field windings, makes the convenient replacement and modification of the internal inductive coils possible, it can present difficulties in the design of flux coils and magnetic probes at the two vertical gaps. Moreover, the KTX has a composite shell consisting of a 6 mm stainless steel vacuum chamber and a 1.5 mm copper shell, which results in limited space for the installation of saddle sensors. Therefore, the double-C structure and composite shell should be considered, especially during the design and installation of the electromagnetic diagnostic system (EDS). The inner surface of the vacuum vessel includes two types of probes. One type is for the measurement of the global plasma parameters, and the other type is for studying the local behavior of the plasma and operating the new saddle coils. In addition, the probes on the outer surface of the composite shell are used for measurements of eddy currents. Finally, saddle sensors for radial field measurements for feedback control were installed between the conducting shell and the vacuum vessel. The entire system includes approximately 1100 magnetic probes, 14 flux coils, 4 ×26 ×2 saddle sensors, and 16 Rogowski coils. Considering the large number of probes and limited space available in the vacuum vessel, the miniaturization of the probes and optimization of the probe distribution are necessary. In addition, accurate calibration and careful mounting of the probes are also required. The frequency response of the designed magnetic probes is up to 200 kHz, and the resolution is 1 G. The EDS, being spherical and of high precision, is one of the most basic and effective diagnostic tools of the KTX and meets the demands imposed by requirements on
An alternative to the compact torus ICF driver
International Nuclear Information System (INIS)
Latter, A.L.; Martinelli, E.A.
1992-11-01
Plasma guns have been used in the Controlled Thermonuclear Reaction (CTR) Program to inject energetic deuterium-tritium plasma into a magnetic confinement machine, also for dense-plasma-focus devices to achieve fusion utilizing Z-pinches. In this report we propose another CTR application of a plasma gun: accelerating the plasma in a coaxial geometry to a speed in the neighborhood of a centimeter per shake with a total kinetic energy of about 20 MJ. The kinetic energy is efficiently converted to x-rays in a time of about a shake, and the x-ray pulse is used to implode an Inertial Confinement Fusion (ICF) capsule. As far as we know the plasma gun application we are proposing has not been explored before, but we observe that the LLNL Compact Torus Program hopes to accelerate a compact-torus-plasma to a comparable speed and energy and, in one of its applications, to generate x-rays for ICF purposes. In fact, the only difference between the LLNL Compact Torus Program and what we are proposing is that our plasma does not rely on imbedded magnetic fields and currents to minimize instabilities. We minimize instabilities by snowplowing the plasma to its required speed in a single shock. Which approach is better requires additional investigation
Compact torus accelerator as a driver for ICF
International Nuclear Information System (INIS)
Tobin, M.T.; Meier, W.R.; Morse, E.C.
1986-01-01
The authors have carried out further investigations of the technical issues associated with using a compact torus (CT) accelerator as a driver for inertial confinement fusion (ICF). In a CT accelerator, a magnetically confined, torus-shaped plasma is compressed, accelerated, and focused by two concentric electrodes. After its initial formation, the torus shape is maintained for lifetimes exceeding 1 ms by inherent poloidal and toroidal currents. Hartman suggests acceleration and focusing of such a plasma ring will not cause dissolution within certain constraints. In this study, we evaluated a point design based on an available capacitor bank energy of 9.2 MJ. This accelerator, which was modeled by a zero-dimensional code, produces a xenon plasma ring with a 0.73-cm radius, a velocity of 4.14 x 10 9 cm/s, and a mass of 4.42 μg. The energy of the plasma ring as it leaves the accelerator is 3.8 MJ, or 41% of the capacitor bank energy. Our studies confirm the feasibility of producing a plasma ring with the characteristics required to induce fusion in an ICF target with a gain greater than 50. The low cost and high efficiency of the CT accelerator are particularly attractive. Uncertainties concerning propagation, accelerator lifetime, and power supply must be resolved to establish the viability of the accelerator as an ICF driver
ITER - torus vacuum pumping system remote handling issues
International Nuclear Information System (INIS)
Stringer, J.
1992-11-01
This report describes further design issues concerning remote maintenance of torus vacuum pumping systems options for ITER. The key issues under investigation in this report are flask support systems for valve seal exchange operations for the compound cryopump scheme and remote maintenance of a proposed multiple turbomolecular pump (TMP) system, an alternative ITER torus exhaust pumping option. Previous studies have shown that the overhead support methods for seal exchange flask equipment could malfunction due to valve/flask misalignment. A floor-mounted support system is described in this report. This scheme provides a more rigid support system for seal exchange operations. An alternative torus pumping system, based on the use of multiple TMPs, is studied from a remote maintenance standpoint. In this concept, centre distance spacing for pump/valve assemblies is too restrictive for remote maintenance. Recommendations are made for adequate spacing of these assemblies based on commercially-available 0.8 m and 1.0 m diameter valves. Fewer pumps will fit in this arrangement, which implies a need for larger TMPs. Pumps of this size are not commercially available. Other concerns regarding the servicing and storage of remote handling equipment in cells are also identified. (9 figs.)
International Nuclear Information System (INIS)
Hillis, D.L.; Wilgen, J.B.; Bigelow, T.S.; Jaeger, E.F.; Swain, D.W.; Hankins, O.E.; Juhala, R.E.
1986-10-01
The hot electron rings of the ELMO Bumpy Torus (EBT) [Plasma Physics and Controlled Nuclear Fusion (IAEA, Vienna, 1975), Vol. II, p. 141] are formed by electron cyclotron resonance heating (ECRH) and have an electron temperature of 350 to 500 keV. The original intention of these hot electron rings was to provide a local minimum in the magnetic field and, thereby, stabilize the simple interchange and flute modes, which are inherent in a closed field line bumpy torus. To evaluate the electron energy density of the EBT rings and determine if enough stored energy is present to provide a local minimum in the magnetic field, a detailed understanding of the spatial distribution of the rings is imperative. The purpose of this report is to measure the ring thickness and investigate its implications for bumpy torus stability. The spatial location and radial profile of the hot electron ring are measured with a unique metal ball pellet injector, which injects small metallic balls into the EBT ring plasma. From these measurements the radial extent (or ring thickness) is about 5 to 7 cm full width at half maximum for typical EBT operation, which is much larger than previously expected. These measurements and recent modeling of the EBT plasma indicate that the hot electron ring's stored energy may not be sufficient to produce a local minimum in the magnetic field
Transport in a small aspect ratio torus
International Nuclear Information System (INIS)
White, R.B.; Gates, D.A.; Mynick, H.E.
2005-01-01
Transport theory in toroidal devices often assumes large aspect ratio and also assumes the poloidal field is small compared to the toroidal field. These assumptions result in transport which in the low collision rate limit is dominated by banana orbits, giving the largest collisionless excursion of a particle from an initial flux surface. However in a small aspect ratio device the gyro radius may be larger than the banana excursion, resulting in significant deviations from the standard neoclassical predictions. In this paper we report numerical simulation of diffusion in low and high beta low aspect ratio equilibria. We also sketch an analytic theory. The diffusion, which we refer to as omniclassical, is a combination of neoclassical and properly averaged classical effects, and can be two or three times the neoclassical value. Good agreement of the analytic theory with numerical simulations is obtained. (author)
van der Meer, Pieter F; Cancelas, Jose A; Vassallo, Ralph R; Rugg, Neeta; Einarson, Mindy; Hess, John R
2011-01-01
Whole blood (WB) must be refrigerated within 8 hours to optimize Factor VIII: C yield, but chilled platelets (PLTs) are rapidly removed from circulation and cannot be used clinically. It is logistically preferable to hold WB overnight at room temperature for next-day processing. We compared in vitro quality of PLT-rich plasma (PRP)-derived PLT concentrates (PCs) from fresh versus overnight-held WB. Four units of WB were pooled and split to prevent donor-dependent differences. One unit was processed immediately; three others were held at room temperature and processed after 24 to 26 hours. After soft-spin centrifugation, PRP was separated from the red blood cells. PRP was hard-spun to make PLT-poor plasma, and the PLTs were resuspended in approximately 60 mL of plasma and stored for 7 days (n = 8 paired experiments by two blood centers). After overnight hold, the PLT concentration was 1.37 × 10(9) ± 0.19 × 10(9) /mL versus 1.03 × 10(9) ± 0.32 × 10(9) /mL for freshly prepared PCs (p < 0.05). pH and glucose were significantly lower and lactate higher for overnight-held units on Day 1, but by Day 5, the differences had disappeared. Hypotonic shock response was initially better, 73 ± 14% for overnight-held versus 53 ± 12% for freshly processed (p < 0.001), but this difference also disappeared during storage. Activation marker CD62P was not different. In vitro storage conditions produce immediate differences after preparation, which disappear throughout storage. PCs from overnight-held WB have similar in vitro variables as from freshly processed WB. These findings warrant confirmation in clinical trials, but underscore the possibility of use of these PCs as being equivalent to those obtained from freshly processed WB. © 2010 American Association of Blood Banks.
Initial assessments of ignition spherical torus
International Nuclear Information System (INIS)
Peng, Y.K.M.; Borowski, S.K.; Bussell, G.T.
1985-12-01
Initial assessments of ignition spherical tori suggest that they can be highly cost effective and exceptionally small in unit size. Assuming advanced methods of current drive to ramp up the plasma current (e.g., via lower hybrid wave at modest plasma densities and temperatures), the inductive solenoid can largely be eliminated. Given the uncertainties in plasma energy confinement times and the effects of strong paramagnetism on plasma pressure, and allowing for the possible use of high-strength copper alloys (e.g., C-17510, Cu-Ni-Be alloy), ignition spherical tori with a 50-s burn are estimated to have major radii ranging from 1.0 to 1.6 m, aspect ratios from 1.4 to 1.7, vacuum toroidal fields from 2 to 3 T, plasma currents from 10 to 19 MA, and fusion power from 50 to 300 MW. Because of its modest field strength and simple poloidal field coil configuration, only conventional engineering approaches are needed in the design. A free-standing toroidal field coil/vacuum vessel structure is assessed to be feasible and relatively independent of the shield structure and the poloidal field coils. This exceptionally simple configuration depends significantly, however, on practical fabrication approaches of the center conductor post, about which there is presently little experience. 19 refs
Consideration of magnetic field fluctuation measurements in a torus plasma with heavy ion beam probe
International Nuclear Information System (INIS)
Shimizu, A.; Fujisawa, A.; Ohshima, S.; Nakano, H.
2004-03-01
The article discusses feasibility of magnetic fluctuation measurement with a heavy ion beam probe (HIBP) in an axisymmetric torus configuration. In the measurements, path integral fluctuation along the probing beam orbit should be considered as is similar to the density fluctuation measurements with HIBP. A calculation, based on an analytic formula, is performed to estimate the path integral effects for fluctuation patterns that have difference in profile, the correlation length, the radial wavelength, and the poloidal mode number. In addition, the large distance between the plasma and the detector is considered to lessen the path integral effect. As a result, it is found that local fluctuation of magnetic field can be properly detected with a heavy ion beam probe. (author)
International Nuclear Information System (INIS)
Strickler, D.J.; Peng, Y-K.M.; Borowski, S.K.; Selcow, E.C.; Miller, J.B.
1985-01-01
The Ignition Spherical Torus (IST) is a small aspect ratio device retaining only indispensable components along the major axis of a tokamak plasma, such as a cooled, normal conductor producing a toroidal magnetic field. The IST is expected to be a cost-effective approach to ignition by taking advantage of low field, large natural plasma elongation, high plasma current, high beta, and tokamak confinement. These result in compact, high-performance devices with relatively simple magnetic systems as compared with ignition tokamaks of larger aspect ratio. The plasma enhancement of the toroidal field on axis, or plasma paramagnetism, is significant in the IST. The use of this plasma-enhanced field in conventional tokamak beta and density limits leads to increased plasma pressure and performance and therefore smaller device size for a given ignition margin
Observation of instability-induced current redistribution in a spherical-torus plasma.
Menard, J E; Bell, R E; Gates, D A; Kaye, S M; LeBlanc, B P; Levinton, F M; Medley, S S; Sabbagh, S A; Stutman, D; Tritz, K; Yuh, H
2006-09-01
A motional Stark effect diagnostic has been utilized to reconstruct the parallel current density profile in a spherical-torus plasma for the first time. The measured current profile compares favorably with neoclassical theory when no large-scale magnetohydrodynamic instabilities are present in the plasma. However, a current profile anomaly is observed during saturated interchange-type instability activity. This apparent anomaly can be explained by redistribution of neutral beam injection current drive and represents the first observation of interchange-type instabilities causing such redistribution. The associated current profile modifications contribute to sustaining the central safety factor above unity for over five resistive diffusion times, and similar processes may contribute to improved operational scenarios proposed for ITER.
International Nuclear Information System (INIS)
Stringer, J.; Blevins, J.
1992-01-01
A large diameter valve suitable for high vacuum operation is under study for ITER Torus evacuation. The valves must comply with specifications for leak-tightness, radiation resistance, dust tolerance, overpressure, and thermal gradients. Remote maintenance of the seal and valve moving parts without disturbance to the rest of the valve system is a requirement. This paper describes tow methods of seal exchange by remote means. In the first method, a flask is proposed for the valve moving parts exchange in inert gas, when the machine is shut down. In the second method a novel concept is described for seal exchange while under vacuum, without having to bring the machine up to atmosphere. The advantages of this method are that scheduled remote handling (RH) operations and outages for seal replacement are not required. Also, the need for a flask is avoided
Results from the RACE [Ring ACceleration Experiment] Compact Torus Acceleration Experiment
International Nuclear Information System (INIS)
Hammer, J.H.; Hartman, C.W.; Eddleman, J.L.; Kusse, B.
1987-06-01
RACE (Ring ACceleration Experiment) is a proof-of-principle experiment aimed at demonstrating acceleration of magnetically confined compact torus plasma rings to directed kinetic energies well in excess of their magnetic and thermal energies. In the course of the first year of operation the following have been observed: successful formation of rings in the RACE geometry; acceleration of rings with large forces, F/sub accelerate/ ∼F/sub equilibrium/ without apparent degradation of the ring structure; peak velocities of ≅2.5 x 10 8 cm/sec; acceleration efficiency of >30% at speeds of 1.5 x 10 8 cm/sec inferred from trajectory and capacitor bank data; kinetic to magnetic energy ratios ∼10 were observed. Experiments in the near future will be aimed at confirmation of the mass/energy measurements by calorimetry and direct density measurements
International Nuclear Information System (INIS)
Medley, S.S.; Darrow, D.S.; Liu, D.; Roquemore, A.L.
2005-01-01
Early neutral-beam injection is used in the National Spherical Torus Experiment (NSTX) to heat the electrons and slow current penetration which keeps q(0) elevated to avoid deleterious MHD activity and at the same time reduces Ohmic flux consumption, all of which aids long-pulse operation. However, the low plasma current (I p ∼ 0.5 MA) and electron density (n e ∼ 1 x 10 13 cm -3 ) attending early injection lead to elevated orbit and shine through losses. The inherent orbit losses are aggravated by large excursions in the outer gap width during current ramp-up. An investigation of this behavior using various energetic particle diagnostics on NSTX and TRANSP code analysis is presented
Sustainment of spherical tokamak by means of repetitive injection of compact torus plasma
International Nuclear Information System (INIS)
Shimamura, Shin; Matsura, Ken; Takahashi, Tsutomu; Nogi, Yasuyuki
2000-01-01
Sustainment of spherical tokamak (S.T.) has been studied. A compact torus (C.T.) plasma was injected into confinement region by magnetized coaxial gun. For start-up and sustainment of large main spherical tokamak, single pulsed injection of small C.T. is not sufficient in many cases. C.T.plasma injection of high repetition rate is required. For this purpose magnetized coaxial gun was driven with high repetition rate current. The first injected C.T. plasma could start-up S.T. without other help. The repetitive C.T. injection grew and sustained the S.T. plasma. A CCD camera with fast gated image intensifier took a cross sectional view of S.T. during the repetitive C.T. injection. (author)
Gravitational waves from the Papaloizou-Pringle instability in black-hole-torus systems.
Kiuchi, Kenta; Shibata, Masaru; Montero, Pedro J; Font, José A
2011-06-24
Black hole (BH)-torus systems are promising candidates for the central engine of γ-ray bursts (GRBs), and also possible outcomes of the collapse of supermassive stars to supermassive black holes (SMBHs). By three-dimensional general relativistic numerical simulations, we show that an m = 1 nonaxisymmetric instability grows for a wide range of self-gravitating tori orbiting BHs. The resulting nonaxisymmetric structure persists for a time scale much longer than the dynamical one, becoming a strong emitter of large amplitude, quasiperiodic gravitational waves. Our results indicate that both, the central engine of GRBs and newly formed SMBHs, can be strong gravitational wave sources observable by forthcoming ground-based and spacecraft detectors.
Simulations of the lower-hybrid antenna in the Madison Symmetric Torus reversed-field pinch
International Nuclear Information System (INIS)
Carlsson, Johan; Smithe, David; Kaufman, Michael; Goetz, John; Thomas, Mark
2014-01-01
Due to constraints inherent to a reversed-field pinch plasma configuration, an unusual launch structure—the interdigital line—was used for lower-hybrid current-drive experiments in the Madison Symmetric Torus. The antenna design and performance were analyzed using an array of codes (including RANT3D/AORSA1D-H, Microwave Studio and VORPAL). It was found that the voltage phasing was not the intended one. As a result, the parallel-wavenumber spectrum of the launched wave peaks at a value lower than desired, making the accessibility marginal. Further simulations demonstrated that the error can largely be corrected by either lowering the antenna operating frequency or shortening the length of the resonators. (paper)
Beta-limiting MHD instabilities in improved performance NSTX spherical torus plasmas
International Nuclear Information System (INIS)
Menard, J.E.; Bell, M.G.; Bell, R.E.
2003-01-01
Global magnetohydrodynamic stability limits in the National Spherical Torus Experiment (NSTX) have increased significantly recently due to a combination of device and operational improvements. First, more routine H-mode operation with broadened pressure profiles allows access to higher normalized beta and lower internal inductance. Second, the correction of a poloidal field coil induced error-field has largely eliminated locked tearing modes during nor- mal operation and increased the maximum achievable beta. As a result of these improvements, peak beta values have reached (not simultaneously) β t = 35%, β N 6.5, N > = 4.5, β / l i =10, and β= 1.4. High β P operation with reduced tearing activity has allowed a doubling of discharge pulse-length to just over 1 second with sustained periods of β N ∼ 6. Details of the β limit scalings and β-limiting instabilities in various operating regimes are described. (author)
Applications of high energy neutralized ion beams to a compact torus
International Nuclear Information System (INIS)
Rostoker, N.; Katzenstein, J.
1986-01-01
Pulsed ion beams can be produced with ion diodes and Marx generators. The technology exists to produce high energy beams efficiently. A neutralized ion beam has an equal number of co-moving electrons. The resultant beam is electrically neutral, has no net current and can be transported across a magnetic field if the current density is sufficiently large. Preliminary experimental results have been obtained on injecting a neutralized proton beam into a small tokamak. To illuminate the physical processes involved in injection and trapping an experiment has been designed for TEXT. Possible applications to a compact torus include plasma heating, current maintenance and non-equilibrium reactors that do not require ignition. Each application is discussed and comparisons are made with other methods. (author)
Observational Constraints on a Pluto Torus of Circumsolar Neutral Gas
Hill, M. E.; Kollmann, P.; McNutt, R. L., Jr.; Smith, H. T.; Bagenal, F.; Brown, L. E.; Elliott, H. A.; Haggerty, D. K.; Horanyi, M.; Krimigis, S. M.; Kusterer, M. B.; Lisse, C. M.; McComas, D. J.; Piquette, M. R.; Sidrow, E. J.; Strobel, D. F.; Szalay, J.; Vandegriff, J. D.; Zirnstein, E.; Ennico Smith, K.; Olkin, C.; Weaver, H. A., Jr.; Young, L. A.; Stern, S. A.
2015-12-01
We present the concept of a neutral gas torus surrounding the Sun, aligned with Pluto's orbit, and place observational constraints based primarily on comparison of New Horizons (NH) measurements with a 3-D Monte Carlo model adapted from analogous satellite tori surrounding Saturn and Jupiter. Such a torus, or perhaps partial torus, should result from neutral N2 escaping from Pluto's exosphere. Unlike other more massive planets closer to the Sun, neutrals escape Pluto readily owing, e.g., to the high thermal speed relative to the escape velocity. Importantly, escaped neutrals have a long lifetime due to the great distance from the Sun, ~100 years for photoionization of N2 and ~180 years for photoionization of N, which results from disassociated N2. Despite the lengthy 248-year orbit, these long e-folding lifetimes may allow an enhanced neutral population to form an extended gas cloud that modifies the N2 spatial profile near Pluto. These neutrals are not directly observable by NH but once ionized N2+ or N+ are picked up by the solar wind, reaching ~50 keV, making these pickup ions (PUIs) detectable by NH's Pluto Energetic Particle Spectrometer Science Investigation (PEPSSI) instrument. PEPSSI observations analyzed to date may constrain the N2 density; the remaining ~95% of the encounter data, scheduled for downlink in August along with similarly anticipated data from the Solar Wind Around Pluto (SWAP) experiment, should help determine the Pluto outgassing rates. Measurements from SWAP include the solar wind speed, a quantity that greatly enhances PUI studies by enabling us to directly account for the PUI distribution's sensitive dependence on plasma speed. Note that anomalous cosmic ray Si observed at Voyager is overabundant by a factor of ~3000 relative to interstellar composition. This might be related to "outer source" PUIs, but the fact that N2 and Si are indistinguishable in many instruments could mean that N2 is actually driving this apparent Si discrepancy.
The torus parametrization of quasiperiodic LI-classes
Baake, M; Pleasants, P A B
2002-01-01
The torus parametrization of quasiperiodic local isomorphism classes is introduced and used to determine the number of elements in such a class with special symmetries or inflation properties. The method is explained in an illustrative fashion for some widely used tiling classes with golden mean rescaling, namely for the Fibonacci chain (1D), the triangle and Penrose patterns (2D) and for Kramer's and Danzer's icosahedral tilings (3D). We obtain a rather complete picture of the orbit structure within these classes, but discuss also various general results.
A Direct Approach to the Villarceau Circles of a Torus.
1984-03-01
8217 following theorem . , Theorem 1. On F and F’ we select points P and P’, respectively, such that (4) 8 "LAOP, * =LAO’P’, (0 ( 8, * < 2), bi X,$ x ~-2- i4...6) by replacing c by -c. Proof of Theorem 1. In the cartesian, axes O’xyz of Fig. I we have .1, 1)P: x c + aoo 0, y- a sin0, z 0 -3- We now rotate...Bottema, Cirkels op een torus, Pythagoras , 19 (1979) 2 7. 2. Z. A. Nelzak, Invitation to Geometry, John Wiley & Sons, New York, 1983. 3. Y. Villarceau
Monte Carlo neutral density calculations for ELMO Bumpy Torus
International Nuclear Information System (INIS)
Davis, W.A.; Colchin, R.J.
1986-11-01
The steady-state nature of the ELMO Bumpy Torus (EBT) plasma implies that the neutral density at any point inside the plasma volume will determine the local particle confinement time. This paper describes a Monte Carlo calculation of three-dimensional atomic and molecular neutral density profiles in EBT. The calculation has been done using various models for neutral source points, for launching schemes, for plasma profiles, and for plasma densities and temperatures. Calculated results are compared with experimental observations - principally spectroscopic measurements - both for guidance in normalization and for overall consistency checks. Implications of the predicted neutral profiles for the fast-ion-decay measurement of neutral densities are also addressed
Legendrian and transverse cables of positive torus knots
DEFF Research Database (Denmark)
Etnyre, John; LaFountain, Douglas; Tosun, Bülent
2012-01-01
Thurston-Bennequin invariant is arbitrarily far from maximal. We also exhibit Legendrian knots requiring arbitrarily many stabilizations before they become Legendrian isotopic. Similar new phenomena are observed for transverse knots. To achieve these results we define and study "partially thickenable" tori......In this paper we classify Legendrian and transverse knots in the knot types obtained from positive torus knots by cabling. This classification allows us to demonstrate several new phenomena. Specifically, we show there are knot types that have non-destabilizable Legendrian representatives whose...
Numerical study of spherical Torus MHD equilibrium configuration
International Nuclear Information System (INIS)
Cheng Faying; Dong Jiaqi; Wang Aike
2003-01-01
Tokamak equilibrium code SWEQU has been modified so that it can be used for the MHD equilibrium study of low aspect ratio device. Evolution of plasma configuration in start-up phase and double-null divertor configuration in steady-state phase has been simulated using the modified code. Results show that the new code can be used not only to obtain the equilibrium configuration of spherical Torus in steady-state phase, but also to simulate the evolution of plasma in the start-up phase
Quasi-single helicity spectra in the Madison Symmetric Torus
International Nuclear Information System (INIS)
Marrelli, L.; Martin, P.; Spizzo, G.; Franz, P.; Chapman, B.E.; Craig, D.; Sarff, J.S.; Biewer, T.M.; Prager, S.C.; Reardon, J.C.
2002-01-01
Evidence of a self-organized collapse towards a narrow spectrum of magnetic instabilities in the Madison Symmetric Torus [R. N. Dexter, D. W. Kerst, T. W. Lovell, S. C. Prager, and J. C. Sprott, Fusion Technol. 19, 131 (1991)] reversed field pinch device is presented. In this collapsed state, dubbed quasi-single helicity (QSH), the spectrum of magnetic modes condenses spontaneously to one dominant mode more completely than ever before observed. The amplitudes of all but the largest of the m=1 modes decrease in QSH states. New results about thermal features of QSH spectra and the identification of global control parameters for their onset are also discussed
On the existence of star products on quotient spaces of linear Hamiltonian torus actions
DEFF Research Database (Denmark)
Herbig, Hans-Christian; Iyengar, Srikanth B.; Pflaum, Markus J.
2009-01-01
that the Koszul complex on the moment map of an effective linear Hamiltonian torus action is acyclic. We rephrase the nonpositivity condition of Arms and Gotay (Adv Math 79(1):43–103, 1990) for linear Hamiltonian torus actions. It follows that reduced spaces of such actions admit continuous star products....
International Nuclear Information System (INIS)
1987-01-01
This project was undertaken to develop innovative concepts for improving the performance of ELMO Bumpy Torus devices in those aspects of plasma confinement that are particularly relevant to an eventual EBT reactor concept. These include effective magnetic utilization using Andreoletti coils, enhanced confinement using positive ambipolar potentials, and attractive divertor concepts that are compatible with formation and maintenance of ELMO rings. Each of the three major objectives was achieved and, except for the divertor studies, documented for publication and presentation at major scientific meetings. This report provides a brief recapitulation of the major results achieved in the form of a collection of those publications, together with this Introduction
Control System Development Plan for the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Neumeyer, C.; Mueller, D.; Gates, D.A.; Ferron, J.R.
1999-01-01
The National Spherical Torus Experiment (NSTX) has as one of its primary goals the demonstration of the attractiveness of the spherical torus concept as a fusion power plant. Central to this goal is the achievement of high plasma β ( = 2 micro 0 /B 2 a measure of the efficiency of a magnetic plasma confinement system). It has been demonstrated both theoretically and experimentally that the maximum achievable β is a strong function of both local and global plasma parameters. It is therefore important to optimize control of the plasma. To this end a phased development plan for digital plasma control on NSTX is presented. The relative level of sophistication of the control system software and hardware will be increased according to the demands of the experimental program in a three phase plan. During Day 0 (first plasma), a simple coil current control algorithm will initiate plasma operations. During the second phase (Day 1) of plasma operations the control system will continue to use the preprogrammed algorithm to initiate plasma breakdown but will then change over to a rudimentary plasma control scheme based on linear combinations of measured plasma fields and fluxes. The third phase of NSTX plasma control system development will utilize the rtEFIT code, first used on DIII-D, to determine, in real-time, the full plasma equilibrium by inverting the Grad-Shafranov equation. The details of the development plan, including a description of the proposed hardware will be presented
Physics results from the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Kaye, S.; Bell, M.
2000-01-01
The mission of the National Spherical Torus Experiment (NSTX) is to extend the understanding of toroidal physics to low aspect ratio (R/a ∼ 1.25) in low collisionality regimes. NSTX is designed to operate with up to 6 MW of High Harmonic Fast Wave (HHFW) heating and current drive, 5 MW of Neutral Beam Injection (NBI), and Co-Axial Helicity Injection (CHI) for non-inductive startup. Initial experiments focused on establishing conditions that will allow NSTX to achieve its aims of simultaneous high-β t and high-bootstrap current fraction, and to develop methods for non-inductive operation, which will be necessary for Spherical Torus power plants. Ohmic discharges with plasma currents up to 1 MA, stored energies up to 55 kJ, β t ∼ 10%, and a range of shapes and configurations were produced. Density limits in deuterium and helium reached 80% and 120% of the Greenwald limit respectively. Significant electron heating was observed with up to 2.3 MW of HHFW. Up to 270 kA of toroidal current for up to 200 msec was produced noninductively using CHI. Initial NBI experiments were carried out with up to two beam sources (3.2 MW). Plasmas with stored energies of up to 140 kJ and β t =21% were produced
Braid group and anyons on an annulus and a torus
International Nuclear Information System (INIS)
Hatsugai, Y.; Kohmoto, M.; Wu Yongshi
1992-01-01
We present an examination of anyons on a cylinder (or annulus) starting from a braid group analysis. The rule for putting anyons on a lattice has to be modified when the periodic boundary condition is imposed on one direction. In contrast to the annulus, one extra restriction is needed for the cylinder geometry to recover its symmetry. The mean-field (MF) treatment is found to be good until level crossing occurs, and to be better if one starts from the hard-core boson rather than fermion. We also present a construction of anyons on a torus starting from a braid group analysis. The rules of Wen, Dagotto and Fradkin for putting anyons on a torus are reproduced and supplemented. The representation of the braid group is characterized by the anyon statistics θ and the magnetic fluxes Φ x and Φ y threading through the holes. It is shown that the anyon system has a smaller period in Φ x and Φ y than the natural period 1. We perform numerical calculations to investigate the spectral flow and find interesting features in understanding the Fractional Quantum Hall (FQH) effect. (orig.)
Coulomb thermal properties and stability of the Io plasma torus
Barbosa, D. D.; Coroniti, F. V.; Eviatar, A.
1983-01-01
Coulomb collisional energy exchange rates are computed for a model of the Io plasma torus consisting of newly created pickup ions, a background of thermally degraded intermediary ions, and a population of cooler electrons. The electrons are collisionally heated by both the pickup ions and background ions and are cooled by electron impact excitation of plasma ions which radiate in the EUV. It is found that a relative concentration of S III pickup ions forbidden S III/electrons = 0.1 with a temperature of 340 eV can deliver energy to the electrons at a rate of 3 x 10 to the -13th erg/cu cm per sec, sufficient to power the EUV emissions in the Io torus. The model predicts a background ion temperature Ti of about 53 eV and an electron temperature Te of about 5.5 eV on the basis of steady-state energy balance relations at Coulomb rates. The model also predicts electron temperature fluctuations at the 30 percent level on a time scale of less than 11 hours, consistent with recent observations of this phenomenon.
Divertor heat flux mitigation in the National Spherical Torus Experimenta)
Soukhanovskii, V. A.; Maingi, R.; Gates, D. A.; Menard, J. E.; Paul, S. F.; Raman, R.; Roquemore, A. L.; Bell, M. G.; Bell, R. E.; Boedo, J. A.; Bush, C. E.; Kaita, R.; Kugel, H. W.; Leblanc, B. P.; Mueller, D.; NSTX Team
2009-02-01
Steady-state handling of divertor heat flux is a critical issue for both ITER and spherical torus-based devices with compact high power density divertors. Significant reduction of heat flux to the divertor plate has been achieved simultaneously with favorable core and pedestal confinement and stability properties in a highly shaped lower single null configuration in the National Spherical Torus Experiment (NSTX) [M. Ono et al., Nucl. Fusion 40, 557 2000] using high magnetic flux expansion at the divertor strike point and the radiative divertor technique. A partial detachment of the outer strike point was achieved with divertor deuterium injection leading to peak flux reduction from 4-6MWm-2to0.5-2MWm-2 in small-ELM 0.8-1.0MA, 4-6MW neutral beam injection-heated H-mode discharges. A self-consistent picture of the outer strike point partial detachment was evident from divertor heat flux profiles and recombination, particle flux and neutral pressure measurements. Analytic scrape-off layer parallel transport models were used for interpretation of NSTX detachment experiments. The modeling showed that the observed peak heat flux reduction and detachment are possible with high radiated power and momentum loss fractions, achievable with divertor gas injection, and nearly impossible to achieve with main electron density, divertor neutral density or recombination increases alone.
Calibration of neutron detectors on the Joint European Torus.
Batistoni, Paola; Popovichev, S; Conroy, S; Lengar, I; Čufar, A; Abhangi, M; Snoj, L; Horton, L
2017-10-01
The present paper describes the findings of the calibration of the neutron yield monitors on the Joint European Torus (JET) performed in 2013 using a 252 Cf source deployed inside the torus by the remote handling system, with particular regard to the calibration of fission chambers which provide the time resolved neutron yield from JET plasmas. The experimental data obtained in toroidal, radial, and vertical scans are presented. These data are first analysed following an analytical approach adopted in the previous neutron calibrations at JET. In this way, a calibration function for the volumetric plasma source is derived which allows us to understand the importance of the different plasma regions and of different spatial profiles of neutron emissivity on fission chamber response. Neutronics analyses have also been performed to calculate the correction factors needed to derive the plasma calibration factors taking into account the different energy spectrum and angular emission distribution of the calibrating (point) 252 Cf source, the discrete positions compared to the plasma volumetric source, and the calibration circumstances. All correction factors are presented and discussed. We discuss also the lessons learnt which are the basis for the on-going 14 MeV neutron calibration at JET and for ITER.
Engineering feasibility of tight aspect ratio Tokamak (spherical torus) reactors
International Nuclear Information System (INIS)
Peng, Y-K.M.; Hicks, J.B.
1990-01-01
Engineering solutions are identified and analyzed for key high-power-density components of tight aspect ratio tokamak reactors (spherical torus reactors). The potentially extreme divertor heat loads can be reduced to about 3 MW/m 2 in expanded divertors using coils inside the demountable toroidal field coils. Given the long and narrow divertor channels, gaseous divertor targets become possible, which eliminate sputtering and increase the divertor life. The unshielded centre conductor post (CCP) of the toroidal field coil can be made of a single dispersion strengthened copper conductor cooled by high-velocity pressurized water to maintain acceptable copper temperature and strength. Damage and activation of the CCP at a neutron fluence of 10 MW-a/m 2 are also tolerable. Annual replacement of the centre post, the divertor assemblies and the blanket can be accomplished with vertical access for all torus components, which are modularized to reduce size and weight. The technical requirements of these solutions are shown to be comparable with, if not less demanding than, those estimated for conventional tokamak reactors. (author)
A six-mode truncation of the Navier-Stokes equations on a two-dimensional torus: a numerical study
International Nuclear Information System (INIS)
Angelo, P.M.; Riela, G.
1981-01-01
We study a model obtained from a six-mode truncation of the Navier-Stokes equations for a two-dimensional incompressible fluid on a torus. We find that at low values of the Reynolds number R the dynamics is characterized by fixed points and, at large values of R, by two stable periodic orbits; at intermediate values of R two infinite sequences of bifurcations of periodic orbits into periodic orbits of doubled period lead to two regions of ''turbulent'' or ''chaotic'' behaviour. The turbulent regions end up for values of R for which stable periodic orbits appear. (author)
Magnetic translation groups in an n-dimensional torus and their representations
International Nuclear Information System (INIS)
Tanimura, Shogo
2002-01-01
A charged particle in a uniform magnetic field in a two-dimensional torus has a discrete noncommutative translation symmetry instead of a continuous commutative translation symmetry. We study topology and symmetry of a particle in a magnetic field in a torus of arbitrary dimensions. The magnetic translation group (MTG) is defined as a group of translations that leave the gauge field invariant. We show that the MTG in an n-dimensional torus is isomorphic to a central extension of a cyclic group Z ν 1 x···xZ ν 2l xT m by U(1) with 2l+m=n. We construct and classify irreducible unitary representations of the MTG in a three-torus and apply the representation theory to three examples. We briefly describe a representation theory for a general n-torus. The MTG in an n-torus can be regarded as a generalization of the so-called noncommutative torus
Imaging the Obscuring Torus in Nearby Active Galaxies
Wilson, Andrew S.; Storchi Bergmann, Thaisa; Morris, Simon
2000-02-01
We propose to study a sample of Seyfert galaxies with the aim of resolving spatially the torus of dense molecular gas and dust which is believed to surround the nuclei of these objects. The galaxies, selected to have strong molecular hydrogen emission and jet-like radio continuum sources, will be imaged in various molecular hydrogen lines and in [Fe II] or Br (gamma). The goals are to a) confirm the existence of such tori, b) determine whether the extended molecular gas is excited thermally or through fluorescence, and c) compare with the distribution of ionized gas, which may show an ionization cone structure from polar escape of ionizing photons. The availability of IR imaging capabilities with tip-tilt and narrow-band filters, which allow imaging in the H_2(lambda) 2.122(micron) line up to a recession velocity of 6,000 km s^-1, makes the Blanco 4m telescope very well suited to this project.
Numerical model for radial transport in the ELMO Bumpy Torus
International Nuclear Information System (INIS)
Jaeger, E.F.; Hedrick, C.L.
1977-11-01
Neutral and charged particle densities and temperatures are calculated as functions of radius for the toroidal plasma in the ELMO Bumpy Torus (EBT) experiment. Energy dependent ionization and charge-exchange rates, ambipolar diffusion, and self-consistent radial electric field profiles are included. Variation in magnetic field due to finite plasma pressure, effects of energetic electron rings, and transport due to drift waves and magnetic field errors are neglected. Diffusion is assumed to be neoclassical with enhanced losses at low collisionalities. The model reproduces many of the observed features of EBT operation in the quiescent toroidal (T) mode. The self-consistently calculated electric field is everywhere positive (not as in experiments) unless enhanced electron collisionality is included. Solutions for advanced EBT's are obtained and confinement parameters predicted
Experimental device for in-torus handling - EDITH intermediate report
International Nuclear Information System (INIS)
Suppan, A.; Krieg, R.; Krumm, H.G.; Kuehnapfel, U.; Leinemann, K.; Reim, J.; Woll, J.
1993-10-01
The Experimental Device for In-Torus Handling (EDITH) is based on articulated boom system (ABS), consisting of a support structure, the articulated boom transporter (ABT), the end-effector positioning unit (EEPU) and different end-effectors (EE's). It is the prototype of an in-vessel handling system for NET/ITER. In combination with a Full Scale Mock-up, EDITH is required to demonstrate that maintenance of plasma facing components can be carried out with the anticipated reliability and in time. A further aim of EDITH is to allow testing of the articulated boom components and subassemblies. The testbed EDITH and the Full Scale Mock-up are described. In addition, the performance and results of the commissioning and the qualification are summarized and an outlook is given for future tasks. (orig./HP) [de
Measurement of Poloidal Velocity on the National Spherical Torus Experiment
Energy Technology Data Exchange (ETDEWEB)
Ronald E. Bell and Russell Feder
2010-06-04
A diagnostic suite has been developed to measure impurity poloidal flow using charge exchange recombination spectroscopy on the National Spherical Torus Experiment. Toroidal and poloidal viewing systems measure all quantities required to determine the radial electric field. Two sets of up/down symmetric poloidal views are used to measure both active emission in the plane of the neutral heating beams and background emission in a radial plane away from the neutral beams. Differential velocity measurements isolate the line-integrated poloidal velocity from apparent flows due to the energy-dependent chargeexchange cross section. Six f/1.8 spectrometers measure 276 spectra to obtain 75 active and 63 background channels every 10 ms. Local measurements from a similar midplane toroidal viewing system are mapped into two dimensions to allow the inversion of poloidal line-integrated measurements to obtain local poloidal velocity profiles. Radial resolution after inversion is 0.6-1.8 cm from the plasma edge to the center.
Quadratic rational rotations of the torus and dual lattice maps
Kouptsov, K L; Vivaldi, F
2002-01-01
We develop a general formalism for computed-assisted proofs concerning the orbit structure of certain non ergodic piecewise affine maps of the torus, whose eigenvalues are roots of unity. For a specific class of maps, we prove that if the trace is a quadratic irrational (the simplest nontrivial case, comprising 8 maps), then the periodic orbits are organized into finitely many renormalizable families, with exponentially increasing period, plus a finite number of exceptional families. The proof is based on exact computations with algebraic numbers, where units play the role of scaling parameters. Exploiting a duality existing between these maps and lattice maps representing rounded-off planar rotations, we establish the global periodicity of the latter systems, for a set of orbits of full density.
Transient waveform acquisition system for the ELMO Bumpy Torus
International Nuclear Information System (INIS)
Young, K.G.; Burris, R.D.; Hillis, D.H.; Overbey, D.R.
1984-10-01
The transient waveform system described in this report is designed to acquire analog waveforms from the ELMO Bumpy Torus (EBT) diagnostic experiments. Pressure, density, synchrotron radiation, etc., are acquired and digitized with a Kinetic Systems TR812 transient recorder and associated modules located in a CAMAC crate. The system can simultaneously acquire, display, and transmit sets of data consisting of identification parameters and up to 1024 data points for 1 to 64 input signals (frequency range = 0.01 pulse/s to 100 kHz) of data every one or more minutes; thus, it can run continuously without operator intervention. The data are taken on a VAX 11/780 and transmitted to a data base on a DECSystem-10. To aid the programmer in making future modifications to the system, detailed documentation using the Yourdon structural methods has been given
ELMO Bumpy Torus Reactor and power plant: conceptual design study
International Nuclear Information System (INIS)
Bathke, C.G.; Dudziak, D.J.; Krakowski, R.A.
1981-08-01
A complete power plant design of a 1200-MWe ELMO Bumpy Torus Reactor (EBTR) is presented. An emphasis is placed on those features that are unique to the EBT confinement concept, with subsystems and balance-of-plant items that are more generic to magnetic fusion being adapted from past, more extensive tokamak reactor designs. Similar to the latter tokamak studies, this conceptual EBTR design also emphasizes the use of conventional or near state-of-the-art engineering technology and materials. An emphasis is also placed on system accessibility, reliability, and maintainability, as these crucial and desirable characteristics relate to the unique high-aspect-ratio configuration of EBTs. Equal and strong emphasis is given to physics, engineering/technology, and costing/economics components of this design effort. Parametric optimizations and sensitivity studies, using cost-of-electricity as an object function, are reported. Based on these results, the direction for future improvement on an already attractive reactor design is identified
Latitudinal oscillations of plasma within the Io torus
Cummings, W. D.; Dessler, A. J.; Hill, T. W.
1980-01-01
The equilibrium latitude and the period of oscillations about this equilibrium latitude are calculated for a plasma in a centrifugally dominated tilted dipole magnetic field representing Jupiter's inner magnetosphere. It is found that for a hot plasma the equilibrium latitude in the magnetic equator, for a cold plasma it is the centrifugal equator, and for a warm plasma it is somewhere in between. An illustrative model is adopted in which atoms are sputtered from the Jupiter-facing hemisphere of Io and escape Io's gravity to be subsequently ionized some distance from Io. Finally, it is shown that ionization generally does not occur at the equilibrium altitude, and that the resulting latitudinal oscillations provide an explanation for the irregularities in electron concentration within the torus, as reported by the radioastronomy experiment aboard Voyager I.
Energy and helicity of magnetic torus knots and braids
Oberti, Chiara; Ricca, Renzo L.
2018-02-01
By considering steady magnetic fields in the shape of torus knots and unknots in ideal magnetohydrodynamics, we compute some fundamental geometric and physical properties to provide estimates for magnetic energy and helicity. By making use of an appropriate parametrization, we show that knots with dominant toroidal coils that are a good model for solar coronal loops have negligible total torsion contribution to magnetic helicity while writhing number provides a good proxy. Hence, by the algebraic definition of writhe based on crossing numbers, we show that the estimated values of writhe based on image analysis provide reliable information for the exact values of helicity. We also show that magnetic energy is linearly related to helicity, and the effect of the confinement of magnetic field can be expressed in terms of geometric information. These results can find useful application in solar and plasma physics, where braided structures are often present.
Reliability and availability assessments for the next European Torus
International Nuclear Information System (INIS)
Bunde, R.
1988-01-01
To achieve its targets in reasonable time, the Next European Torus (NET) must be operated with considerable reliability and availability (R and A). Therefore, failure modes, effects, and criticality analysis (FMECA) of the overall plant and of its major components is already being performed as the design evolves. The present status of the R and A work is described in four steps: First, the R and A targets envisaged for the NET operation are discussed. Then an FMECA covering the overall plant is described, and a more detailed FMECA of major components is presented concerning the toroidal field coil systeml plasma heating systems; protection, instrumentation, and control systems; first wall and blanket, as well as the cooling system. Finally, the R and A results are compared with the targets, and measures for improvements are given
Physics Basis for a Spherical Torus Power Plant
International Nuclear Information System (INIS)
Kessel, C.E.; Menard, J.; Jardin, S.C.; Mau, T.K.
1999-01-01
The spherical torus, or low-aspect-ratio tokamak, is considered as the basis for a fusion power plant. A special class of wall-stabilized high-beta high-bootstrap fraction low-aspect-ratio tokamak equilibrium are analyzed with respect to MHD stability, bootstrap current and external current drive, poloidal field system requirements, power and particle exhaust and plasma operating regime. Overall systems optimization leads to a choice of aspect ratio A = 1:6, plasma elongation kappa = 3:4, and triangularity delta = 0:64. The design value for the plasma toroidal beta is 50%, corresponding to beta N = 7:4, which is 10% below the ideal stability limit. The bootstrap fraction of 99% greatly alleviates the current drive requirements, which are met by tangential neutral beam injection. The design is such that 45% of the thermal power is radiated in the plasma by Bremsstrahlung and trace Krypton, with Neon in the scrapeoff layer radiating the remainder
Electron energy confinement in ELMO Bumpy Torus (EBT)
International Nuclear Information System (INIS)
Hiroe, S.; Haste, G.R.; Dandl, R.A.
1979-06-01
Using a calibrated, solid-state, soft x-ray detector, the electron temperature and density have been measured over a wide range of operating conditions of ELMO Bumpy Torus (EBT). The empirical relations of the temperature or the density to the microwave power and the ambient pressure have been determined. The toroidally stored energy has been observed to increase as the stored energy of the hot electron annulus increases. The energy confinement time has been obtained for various plasma parameters and has been found to agree with the neoclassical theory. The advantages of EBT collisionless scaling for fusion plasma confinement have been noted, i.e., n/sub e/tau/sub E/ increases as T/sub e/ 1 5 in the collisionless regime
Measurement of Poloidal Velocity on the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Bell, Ronald E.; Feder, Russell
2010-01-01
A diagnostic suite has been developed to measure impurity poloidal flow using charge exchange recombination spectroscopy on the National Spherical Torus Experiment. Toroidal and poloidal viewing systems measure all quantities required to determine the radial electric field. Two sets of up/down symmetric poloidal views are used to measure both active emission in the plane of the neutral heating beams and background emission in a radial plane away from the neutral beams. Differential velocity measurements isolate the line-integrated poloidal velocity from apparent flows due to the energy-dependent chargeexchange cross section. Six f/1.8 spectrometers measure 276 spectra to obtain 75 active and 63 background channels every 10 ms. Local measurements from a similar midplane toroidal viewing system are mapped into two dimensions to allow the inversion of poloidal line-integrated measurements to obtain local poloidal velocity profiles. Radial resolution after inversion is 0.6-1.8 cm from the plasma edge to the center.
Polynomial invariants for torus knots and topological strings
International Nuclear Information System (INIS)
Labastida, J.M.F.
2001-01-01
We make a precision test of a recently proposed conjecture relating Chern-Simons gauge theory to topological string theory on the resolution of the conifold. First, we develop a systematic procedure to extract string amplitudes from vacuum expectation values (vevs) of Wilson loops in Chern-Simons gauge theory, and then we evaluate these vevs in arbitrary irreducible representations of SU(N) for torus knots. We find complete agreement with the predictions derived from the target space interpretation of the string amplitudes. We also show that the structure of the free energy of topological open string theory gives further constraints on the Chern-Simons vevs. Our work provides strong evidence towards an interpretation of knot polynomial invariants as generating functions associated to enumerative problems. (orig.)
I/O routing in a multidimensional torus network
Chen, Dong; Eisley, Noel A.; Heidelberger, Philip
2018-04-24
A method, system and computer program product are disclosed for routing data packet in a computing system comprising a multidimensional torus compute node network including a multitude of compute nodes, and an I/O node network including a plurality of I/O nodes. In one embodiment, the method comprises assigning to each of the data packets a destination address identifying one of the compute nodes; providing each of the data packets with a toio value; routing the data packets through the compute node network to the destination addresses of the data packets; and when each of the data packets reaches the destination address assigned to said each data packet, routing said each data packet to one of the I/O nodes if the toio value of said each data packet is a specified value. In one embodiment, each of the data packets is also provided with an ioreturn value used to route the data packets through the compute node network.
Abelian projection on the torus for general gauge groups
International Nuclear Information System (INIS)
Ford, C.; Tok, T.; Wipf, A.
1999-01-01
We consider Yang-Mills theories with general gauge groups G and twists of the four-torus. We find consistent boundary conditions for gauge fields in all instanton sectors. An extended abelian projection with respect to the Polyakov loop operator is presented, where A 0 is independent of time and in the Cartan subalgebra. Fundamental domains for the gauge fixed A 0 are constructed for arbitrary gauge groups. In the sectors with non-vanishing instanton number such gauge fixings are necessarily singular. The singularities can be restricted to Dirac strings joining magnetically charged defects. The magnetic charges of these monopoles take their values in the co-root lattice of the gauge group. We relate the magnetic charges of the defects and the windings of suitable Higgs fields about these defects to the instanton number
BayesCLUMPY: BAYESIAN INFERENCE WITH CLUMPY DUSTY TORUS MODELS
International Nuclear Information System (INIS)
Asensio Ramos, A.; Ramos Almeida, C.
2009-01-01
Our aim is to present a fast and general Bayesian inference framework based on the synergy between machine learning techniques and standard sampling methods and apply it to infer the physical properties of clumpy dusty torus using infrared photometric high spatial resolution observations of active galactic nuclei. We make use of the Metropolis-Hastings Markov Chain Monte Carlo algorithm for sampling the posterior distribution function. Such distribution results from combining all a priori knowledge about the parameters of the model and the information introduced by the observations. The main difficulty resides in the fact that the model used to explain the observations is computationally demanding and the sampling is very time consuming. For this reason, we apply a set of artificial neural networks that are used to approximate and interpolate a database of models. As a consequence, models not present in the original database can be computed ensuring continuity. We focus on the application of this solution scheme to the recently developed public database of clumpy dusty torus models. The machine learning scheme used in this paper allows us to generate any model from the database using only a factor of 10 -4 of the original size of the database and a factor of 10 -3 in computing time. The posterior distribution obtained for each model parameter allows us to investigate how the observations constrain the parameters and which ones remain partially or completely undetermined, providing statistically relevant confidence intervals. As an example, the application to the nuclear region of Centaurus A shows that the optical depth of the clouds, the total number of clouds, and the radial extent of the cloud distribution zone are well constrained using only six filters. The code is freely available from the authors.
The Nature of the Torus in the Heavily Obscured AGN Markarian 3: an X-Ray Study
Guainazzi, M.; Risaliti, G.; Awaki, H.; Arevalo, P.; Bauer, F. E.; Bianchi, S.; Boggs, S.E; Brandt, W. N.; Brightman, M.; Christensen, F. E.;
2016-01-01
In this paper, we report the results of an X-ray monitoring campaign on the heavily obscured Seyfert galaxy, Markarian 3, carried out between the fall of 2014 and the spring of 2015 with NuSTAR, Suzaku and XMMNewton. The hard X-ray spectrum of Markarian 3 is variable on all the time-scales probed by our campaign, down to a few days. The observed continuum variability is due to an intrinsically variable primary continuum seen in transmission through a large, but still Compton-thin column density (N(sub H) approx. 0.8-1.1 x 10(exp 24)/sq cm). If arranged in a spherical-toroidal geometry, the Compton scattering matter has an opening angle approx. 66deg, and is seen at a grazing angle through its upper rim (inclination angle approx. 70deg). We report a possible occultation event during the 2014 campaign. If the torus is constituted by a system of clouds sharing the same column density, this event allows us to constrain their number (17 +/- 5) and individual column density, [approx. (4.9 +/- 1.5) x 10(exp 22)/ sq cm]. The comparison of IR and X-ray spectroscopic results with state-of-the art torus models suggests that at least two-thirds of the X-ray obscuring gas volume might be located within the dust sublimation radius. We report also the discovery of an ionized absorber, characterized by variable resonant absorption lines due to He- and H-like iron. This discovery lends support to the idea that moderate column density absorbers could be due to clouds evaporated at the outer surface of the torus, possibly accelerated by the radiation pressure due to the central AGN emission leaking through the patchy absorber.
A major modification of the Joint European Torus using teleoperational techniques
International Nuclear Information System (INIS)
Rolfe, A.
1998-04-01
The Joint European Torus (JET) project was set up under the auspices of EURATOM in the late 1970's in order to study the feasibility of controlled Nuclear Fusion. The experimental device comprises a toroidal shaped vacuum vessel in which high temperature plasma is created and controlled. The inside of the torus is now inaccessible to personnel for around one year due to slightly elevated radiation levels. The JET programme however requires the immediate replacement of a major system within the torus and this must therefore be achieved using only remote handling techniques. This paper describes the preparations for this first fully remote handling shutdown at JET. (author)
Computation of Quantum Bound States on a Singly Punctured Two-Torus
International Nuclear Information System (INIS)
Kar-Tim Chan; Zainuddin Hishamuddin; Molladavoudi Saeid
2013-01-01
We study a quantum mechanical system on a singly punctured two-torus with bound states described by the Maass waveforms which are eigenfunctions of the hyperbolic Laplace—Beltrami operator. Since the discrete eigenvalues of the Maass cusp form are not known analytically, they are solved numerically using an adapted algorithm of Hejhal and Then to compute Maass cusp forms on the punctured two-torus. We report on the computational results of the lower lying eigenvalues for the punctured two-torus and find that they are doubly-degenerate. We also visualize the eigenstates of selected eigenvalues using GridMathematica
Schuler, Michael; Whitsitt, Seth; Henry, Louis-Paul; Sachdev, Subir; Läuchli, Andreas M
2016-11-18
The low-energy spectra of many body systems on a torus, of finite size L, are well understood in magnetically ordered and gapped topological phases. However, the spectra at quantum critical points separating such phases are largely unexplored for (2+1)D systems. Using a combination of analytical and numerical techniques, we accurately calculate and analyze the low-energy torus spectrum at an Ising critical point which provides a universal fingerprint of the underlying quantum field theory, with the energy levels given by universal numbers times 1/L. We highlight the implications of a neighboring topological phase on the spectrum by studying the Ising* transition (i.e. the transition between a Z_{2} topological phase and a trivial paramagnet), in the example of the toric code in a longitudinal field, and advocate a phenomenological picture that provides qualitative insight into the operator content of the critical field theory.
International Nuclear Information System (INIS)
Pannarale, Francesco; Tonita, Aaryn; Rezzolla, Luciano
2011-01-01
The merger of a binary system composed of a black hole (BH) and a neutron star (NS) may leave behind a torus of hot, dense matter orbiting around the BH. While numerical-relativity simulations are necessary to simulate this process accurately, they are also computationally expensive and unable at present to cover the large space of possible parameters, which include the relative mass ratio, the stellar compactness, and the BH spin. To mitigate this and provide a first reasonable coverage of the space of parameters, we have developed a method for estimating the mass of the remnant torus from BH-NS mergers. The toy model makes use of an improved relativistic affine model to describe the tidal deformations of an extended tri-axial ellipsoid orbiting around a Kerr BH and measures the mass of the remnant torus by considering which of the fluid particles composing the star are on bound orbits at the time of the tidal disruption. We tune the toy model by using the results of fully general-relativistic simulations obtaining relative precisions of a few percent and use it to investigate the space of parameters extensively. In this way, we find that the torus mass is largest for systems with highly spinning BHs, small stellar compactnesses, and large mass ratios. As an example, tori as massive as M b,tor ≅ 1.33 M sun can be produced for a very extended star with compactness C ≅ 0.1 inspiralling around a BH with dimensionless spin parameter a = 0.85 and mass ratio q ≅ 0.3. However, for a more astrophysically reasonable mass ratio q ≅ 0.14 and a canonical value of the stellar compactness C ≅ 0.145, the toy model sets a considerably smaller upper limit of M b,tor ∼ sun .
International Nuclear Information System (INIS)
Zhang, J.; Wang, Y. H.; Wang, D. Z.
2013-01-01
Understanding the routes to chaos occurring in atmospheric-pressure dielectric barrier discharge systems by changing controlling parameters is very important to predict and control the dynamical behaviors. In this paper, a route of a quasiperiodic torus to chaos via the strange nonchaotic attractor is observed in an atmospheric-pressure dielectric barrier discharge driven by triangle-wave voltage. By increasing the driving frequency, the discharge system first bifurcates to a quasiperiodic torus from a stable single periodic state, and then torus and phase-locking periodic state appear and disappear alternately. In the meantime, the torus becomes increasingly wrinkling and stretching, and gradually approaches a fractal structure with the nonpositive largest Lyapunov exponent, i.e., a strange nonchaotic attractor. After that, the discharge system enters into chaotic state. If the driving frequency is further increased, another well known route of period-doubling bifurcation to chaos is also observed
Energy Technology Data Exchange (ETDEWEB)
Zhang, J.; Wang, Y. H.; Wang, D. Z. [Key Laboratory of Materials Modification by Laser, Electron, and Ion Beams, School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian 116024 (China)
2013-08-15
Understanding the routes to chaos occurring in atmospheric-pressure dielectric barrier discharge systems by changing controlling parameters is very important to predict and control the dynamical behaviors. In this paper, a route of a quasiperiodic torus to chaos via the strange nonchaotic attractor is observed in an atmospheric-pressure dielectric barrier discharge driven by triangle-wave voltage. By increasing the driving frequency, the discharge system first bifurcates to a quasiperiodic torus from a stable single periodic state, and then torus and phase-locking periodic state appear and disappear alternately. In the meantime, the torus becomes increasingly wrinkling and stretching, and gradually approaches a fractal structure with the nonpositive largest Lyapunov exponent, i.e., a strange nonchaotic attractor. After that, the discharge system enters into chaotic state. If the driving frequency is further increased, another well known route of period-doubling bifurcation to chaos is also observed.
MORSE-CGT Monte Carlo radiation transport code with the capability of the torus geometric treatment
International Nuclear Information System (INIS)
Deng Li
1990-01-01
The combinatorial geometry package CGT with the capability of the torus geometric treatment is introduced. It is get by developing the combinatorial geometry package CG. The CGT package can be transplanted to those codes which the CG package is being used and makes them also with the capability. The MORSE-CGT code can be used to solve the neutron, gamma-ray or coupled neutron-gamma-ray transport problems and time dependence for both shielding and criticality problems in torus system or system which is produced by arbitrary finite combining torus with torus or other bodies in CG package and it can also be used to design the blanket and compute shielding for TOKAMAK Fusion-Fission Hybrid Reactor
Conceptual design of the Purdue compact torus/passive liner fusion reactor
International Nuclear Information System (INIS)
Terry, W.K.
1981-01-01
This proposal describes a program for the conceptual development of a novel fusion reactor design, the Purdue Compact Torus/Passive Liner Reactor. The key features of the concept are described and a comparison is made with a conventional tokamak
Comparative study of poloidal field systems for the torus II experiment
International Nuclear Information System (INIS)
Farvaque, L.; Ghazal, S.; Leloup, C.; Pariente, M.; CEA Centre d'Etudes Nucleaires de Fontenay-aux-Roses, 92
1976-11-01
Three types of transformer for the TORUS II experiment are compared: a saturated iron core transformer with an entire magnetic circuit, an air core transformer and a saturated iron core transformer restricted to the central limb [fr
Infrared emission in Seyfert 2 galaxies - Reprocessed radiation from a dusty torus?
Storchi-Bergmann, Thaisa; Mulchaey, John S.; Wilson, Andrew S.
1992-01-01
New and existing data for a sample of nine Seyfert 2 galaxies with known 'ionization cones' are combined in order to test whether collimation results from shadowing of radiation from a small isotropic nuclear source by a thick dusty torus. The number of ionizing photons emitted by the compact nucleus is calculated from the emission-line ratios measured for gas within the cones. On the assumption that this compact nuclear source radiates isotropically, the optical-UV power incident on the torus, which is expected to be reradiated in the IR, is determined. It is found that the observed IRAS luminosities are consistent with the torus model in eight of the nine objects with sufficient data to perform the calculation. It is concluded that the data are generally consistent with collimation and reradiation by a dusty torus.
SDN Data Center Performance Evaluation of Torus and Hypercube Interconnecting Schemes
DEFF Research Database (Denmark)
Andrus, Bogdan-Mihai; Vegas Olmos, Juan José; Mehmeri, Victor
2015-01-01
— By measuring throughput, delay, loss-rate and jitter, we present how SDN framework yields a 45% performance increase in highly interconnected topologies like torus and hypercube compared to current Layer2 switching technologies, applied to data center architectures......— By measuring throughput, delay, loss-rate and jitter, we present how SDN framework yields a 45% performance increase in highly interconnected topologies like torus and hypercube compared to current Layer2 switching technologies, applied to data center architectures...
Minimal Liouville gravity on the torus via the Douglas string equation
International Nuclear Information System (INIS)
Spodyneiko, Lev
2015-01-01
In this paper we assume that the partition function in minimal Liouville gravity (MLG) obeys the Douglas string equation. This conjecture makes it possible to compute the torus correlation numbers in (3,p) MLG. We perform this calculation using also the resonance relations between the coupling constants in the KdV frame and in the Liouville frame. We obtain explicit expressions for the torus partition function and for the one- and two-point correlation numbers. (paper)
10D massive type IIA supergravities as the uplift of parabolic M2-brane torus bundles
Energy Technology Data Exchange (ETDEWEB)
Garcia del Moral, Maria Pilar [Universidad de Antofagasta (Chile). Dept. de Fisica; Restuccia, Alvaro [Universidad de Antofagasta (Chile). Dept. de Fisica; Universidad Simon Bolivar, Caracas (Venezuela, Bolivarian Republic of). Dept. de Fisica
2016-04-15
We remark that the two 10D massive deformations of the N = 2 maximal type IIA supergravity (Romans and HLW supergravity) are associated to the low energy limit of the uplift to 10D of M2-brane torus bundles with parabolic monodromy linearly and non-linearly realized respectively. Romans supergravity corresponds to M2-brane compactified on a twice-punctured torus bundle. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)
Progress Towards High Performance, Steady-state Spherical Torus
International Nuclear Information System (INIS)
Ono, M.; Bell, M.G.; Bell, R.E.; Bigelow, T.; Bitter, M.; Blanchard, W.; Boedo, J.; Bourdelle, C.; Bush, C.; Choe, W.; Chrzanowski, J.; Darrow, D.S.; Diem, S.J.; Doerner, R.; Efthimion, P.C.; Ferron, J.R.; Fonck, R.J.; Fredrickson, E.D.; Garstka, G.D.; Gates, D.A.; Gray, T.; Grisham, L.R.; Heidbrink, W.; Hill, K.W.; Hoffman, D.; Jarboe, T.R.; Johnson, D.W.; Kaita, R.; Kaye, S.M.; Kessel, C.; Kim, J.H.; Kissick, M.W.; Kubota, S.; Kugel, H.W.; LeBlanc, B.P.; Lee, K.; Lee, S.G.; Lewicki, B.T.; Luckhardt, S.; Maingi, R.; Majeski, R.; Manickam, J.; Maqueda, R.; Mau, T.K.; Mazzucato, E.; Medley, S.S.; Menard, J.; Mueller, D.; Nelson, B.A.; Neumeyer, C.; Nishino, N.; Ostrander, C.N.; Pacella, D.; Paoletti, F.; Park, H.K.; Park, W.; Paul, S.F.; Peng, Y.-K. M.; Phillips, C.K.; Pinsker, R.; Probert, P.H.; Ramakrishnan, S.; Raman, R.; Redi, M.; Roquemore, A.L.; Rosenberg, A.; Ryan, P.M.; Sabbagh, S.A.; Schaffer, M.; Schooff, R.J.; Seraydarian, R.; Skinner, C.H.; Sontag, A.C.; Soukhanovskii, V.; Spaleta, J.; Stevenson, T.; Stutman, D.; Swain, D.W.; Synakowski, E.; Takase, Y.; Tang, X.; Taylor, G.; Timberlake, J.; Tritz, K.L.; Unterberg, E.A.; Von Halle, A.; Wilgen, J.; Williams, M.; Wilson, J.R.; Xu, X.; Zweben, S.J.; Akers, R.; Barry, R.E.; Beiersdorfer, P.; Bialek, J.M.; Blagojevic, B.; Bonoli, P.T.; Carter, M.D.; Davis, W.; Deng, B.; Dudek, L.; Egedal, J.; Ellis, R.; Finkenthal, M.; Foley, J.; Fredd, E.; Glasser, A.; Gibney, T.; Gilmore, M.; Goldston, R.J.; Hatcher, R.E.; Hawryluk, R.J.; Houlberg, W.; Harvey, R.; Jardin, S.C.; Hosea, J.C.; Ji, H.; Kalish, M.; Lowrance, J.; Lao, L.L.; Levinton, F.M.; Luhmann, N.C.; Marsala, R.; Mastravito, D.; Menon, M.M.; Mitarai, O.; Nagata, M.; Oliaro, G.; Parsells, R.; Peebles, T.; Peneflor, B.; Piglowski, D.; Porter, G.D.; Ram, A.K.; Rensink, M.; Rewoldt, G.; Roney, P.; Shaing, K.; Shiraiwa, S.; Sichta, P.; Stotler, D.; Stratton, B.C.; Vero, R.; Wampler, W.R.; Wurden, G.A.
2003-01-01
Research on the Spherical Torus (or Spherical Tokamak) is being pursued to explore the scientific benefits of modifying the field line structure from that in more moderate aspect-ratio devices, such as the conventional tokamak. The Spherical Tours (ST) experiments are being conducted in various U.S. research facilities including the MA-class National Spherical Torus Experiment (NSTX) at Princeton, and three medium-size ST research facilities: Pegasus at University of Wisconsin, HIT-II at University of Washington, and CDX-U at Princeton. In the context of the fusion energy development path being formulated in the U.S., an ST-based Component Test Facility (CTF) and, ultimately a Demo device, are being discussed. For these, it is essential to develop high-performance, steady-state operational scenarios. The relevant scientific issues are energy confinement, MHD stability at high beta (B), noninductive sustainment, ohmic-solenoid-free start-up, and power and particle handling. In the confinement area, the NSTX experiments have shown that the confinement can be up to 50% better than the ITER-98-pby2 H-mode scaling, consistent with the requirements for an ST-based CTF and Demo. In NSTX, CTF-relevant average toroidal beta values bT of up to 35% with the near unity central betaT have been obtained. NSTX will be exploring advanced regimes where bT up to 40% can be sustained through active stabilization of resistive wall modes. To date, the most successful technique for noninductive sustainment in NSTX is the high beta-poloidal regime, where discharges with a high noninductive fraction (∼60% bootstrap current + neutral-beam-injected current drive) were sustained over the resistive skin time. Research on radio-frequency-based heating and current drive utilizing HHFW (High Harmonic Fast Wave) and EBW (Electron Bernstein Wave) is also pursued on NSTX, Pegasus, and CDX-U. For noninductive start-up, the Coaxial Helicity Injection (CHI), developed in HIT/HIT-II, has been adopted
Particle on a torus knot: Constrained dynamics and semi-classical quantization in a magnetic field
Energy Technology Data Exchange (ETDEWEB)
Das, Praloy, E-mail: praloydasdurgapur@gmail.com; Pramanik, Souvik, E-mail: souvick.in@gmail.com; Ghosh, Subir, E-mail: subirghosh20@gmail.com
2016-11-15
Kinematics and dynamics of a particle moving on a torus knot poses an interesting problem as a constrained system. In the first part of the paper we have derived the modified symplectic structure or Dirac brackets of the above model in Dirac’s Hamiltonian framework, both in toroidal and Cartesian coordinate systems. This algebra has been used to study the dynamics, in particular small fluctuations in motion around a specific torus. The spatial symmetries of the system have also been studied. In the second part of the paper we have considered the quantum theory of a charge moving in a torus knot in the presence of a uniform magnetic field along the axis of the torus in a semiclassical quantization framework. We exploit the Einstein–Brillouin–Keller (EBK) scheme of quantization that is appropriate for multidimensional systems. Embedding of the knot on a specific torus is inherently two dimensional that gives rise to two quantization conditions. This shows that although the system, after imposing the knot condition reduces to a one dimensional system, even then it has manifested non-planar features which shows up again in the study of fractional angular momentum. Finally we compare the results obtained from EBK (multi-dimensional) and Bohr–Sommerfeld (single dimensional) schemes. The energy levels and fractional spin depend on the torus knot parameters that specifies its non-planar features. Interestingly, we show that there can be non-planar corrections to the planar anyon-like fractional spin.
Kinetic transport model for the ELMO Bumpy Torus
International Nuclear Information System (INIS)
Jaeger, E.F.; Hedrick, C.L.; Tolliver, J.S.
1978-05-01
A bounce-averaged drift kinetic equation is solved for the toroidal plasma in the ELMO Bumpy Torus (EBT). The distribution function is assumed isotropic in pitch angle and calculated as a function of radius and speed using finite differences on a two-dimensional grid. A Fokker-Planck representation of the collision operator includes Coulomb, microwave, ionizing, and charge-exchange collisions. Ion and electron fluxes, computed as integrals of the distribution function, are of comparable magnitude for ambipolar potentials which are approximately self-consistent. Initial results assume an unperturbed distribution function which is Maxwellian; however, this is not a necessary assumption in the model. Careful accounting of loss regions where electric and magnetic poloidal drifts cancel (super banana particle orbits) leads to ion loss rates which are in some cases two orders of magnitude greater than electron rates. In these cases, radially inward pointing self-consistent electric fields occur with potentials on the order of a few times the ion temperature. These negative field results are in approximate agreement with experiment and appear to be stable to the electric field runaway encountered in positive field cases
Design of the new magnetic sensors for Joint European Torus
International Nuclear Information System (INIS)
Coccorese, V.; Albanese, R.; Altmann, H.; Cramp, S.; Edlington, T.; Fullard, K.; Gerasimov, S.; Huntley, S.; Lam, N.; Loving, A.; Riccardo, V.; Sartori, F.; Marren, C.; McCarron, E.; Sowden, C.; Tidmarsh, J.; Basso, F.; Cenedese, A.; Chitarin, G.; DegliAgostini, F.
2004-01-01
A new magnetic diagnostics system has been designed for the 2005 Joint European Torus (JET) experimental campaigns onward. The new system, which adds to the existing sensors, aims to improve the JET safety, reliability, and performance, with respect to: (i) equilibrium reconstruction; (ii) plasma shape control; (iii) coil failures; (iv) VDEs; (v) iron modeling; and (vi) magnetohydrodynamics poloidal mode analysis. The system consists of in-vessel and ex-vessel sensors. The former are a set of 38 coil pairs (normal and tangential), located as near as possible to the plasma. Coils are generally grouped in rails, in order to ease remote handling in-vessel installation. The system includes: (i) two outer poloidal limiter arrays (2x7 coil pairs); (ii) two divertor region arrays (2x7 coil pairs); and (iii) two top coil arrays (2x5 coil pairs). Ex-vessel sensors, including discrete coils, Hall probes, and flux loops (26 in total) will be installed on the iron limbs, in order to provide experimental data for the treatment of iron in equilibrium codes. The design is accompanied by a software analysis, aiming to predict the expected improvement
Neutral beam power measurements inside the ASDEX torus
International Nuclear Information System (INIS)
Zengliang, Y.; Staebler, A.; Vollmer, O.
1982-11-01
Neutral beam power measurements inside the ASDEX torus are done with a retractable calorimeter which is only radiation cooled. The calorimeter plate made from Molybdenum is subdivided into nine segments whose increase in energy content due to a shot yields the absorbed beam power. Different models for the backward extrapolation of the measured temperature curves are examined for a series of low energy shots with the result that pure radiation cooling is a valid assumption. Furthermore, a temperature correction to the measured power is derived from these experiments. The evaluation of the shots onto this calorimeter is done by a computer program. The application of this program to a few full power shots shows that a neutral power up to 3.2 MW has been injected into the ASDEX vessel by the two injectors with an overall efficiency of up to 40%. Reionization losses due to the ASDEX stray field are less than 10%; they do not show any dependence upon the pulse length for shots up to 200 ms. (orig.)
New Capabilities and Results for the National Spherical Torus Experiment
Energy Technology Data Exchange (ETDEWEB)
M.G. Bell, R.E. Bell, D.A. Gates, S.M. Kaye, H. Kugel, B.P. LeBlanc, F.M. Levinton, R. Maingi, J.E. Menard, R. Raman, S.A. Sabbagh, D. Stutman and the NSTX Research Team
2008-02-29
The National Spherical Torus Experiment (NSTX) produces plasmas with toroidal aspect ratio as low as 1.25, which can be heated by up to 6 MW High-Harmonic Fast Waves and up to 7 MW of deuterium Neutral Beam Injection. Using new poloidal fields coils, plasmas with cross-section elongation up to 2.7, triangularity 0.8, plasma currents Ip up to 1.5 MA and normalized currents Ip/a·BT up to 7.5 MA/m·T have been achieved. A significant extension of the plasma pulse length, to 1.5 s at a plasma current of 0.7 MA, has been achieved by exploiting the bootstrap and NBI-driven currents to reduce the dissipation of poloidal flux. Inductive plasma startup has been supplemented by Coaxial Helicity Injection (CHI) and the production of persistent current on closed flux surfaces by CHI has now been demonstrated in NSTX. The plasma response to magnetic field perturbations with toroidal mode numbers n = 1 or 3 and the effects on the plasma rotation have been investigated using three pairs of coils outside the vacuum vessel. Recent studies of both MHD stability and of transport benefitted from improved diagnostics, including measurements of the internal poloidal field using the motional Stark effect (MSE). In plasmas with a region of reversed magnetic shear in the core, now confirmed by the MSE data, improved electron confinement has been observed.
Transient Transport Experiments in the CDX-U Spherical Torus
International Nuclear Information System (INIS)
T. Munsat; P.C. Efthimion; B. Jones; R. Kaita; R. Majeski; D. Stutman; G. Taylor
2001-01-01
Electron transport has been measured in the Current Drive Experiment-Upgrade (CDX-U) using two separate perturbative techniques. Gas modulation at the plasma edge was used to introduce cold-pulses which propagate towards the plasma center, providing time-of-flight information leading to a determination of chi(subscript e) as a function of radius. Sawteeth at the q=1 radius (r/a ∼ 0.15) induced heat-pulses which propagated outward towards the plasma edge, providing a complementary time-of-flight based chi(subscript e) profile measurement. This work represents the first localized measurement of chi(subscript e) in a spherical torus. It is found that chi(subscript e) = 1-2 meters squared per second in the plasma core (r/a < 1/3), increasing by an order of magnitude or more outside of this region. Furthermore, the chi(subscript e) profile exhibits a sharp transition near r/a = 1/3. Spectral and profile analyses of the soft X-rays, scanning interferometer, and edge probe data show no evidence of a significant magnetic island causing the high chi(subscript e) region
Electron Bernstein Wave Research on the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Taylor, G.; Bers, A.; Bigelow, T.S.; Carter, M.D.; Caughman, J.B.; Decker, J.; Diem, S.; Efthimion, P.C.; Ershov, N.M.; Fredd, E.; Harvey, R.W.; Hosea, J.; Jaeger, F.; Preinhaelter, J.; Ram, A.K.; Rasmussen, D.A.; Smirnov, A.P.; Wilgen, J.B.; Wilson, J.R.
2005-01-01
Off-axis electron Bernstein wave current drive (EBWCD) may be critical for sustaining noninductive high-beta National Spherical Torus Experiment (NSTX) plasmas. Numerical modeling results predict that the ∼100 kA of off-axis current needed to stabilize a solenoid-free high-beta NSTX plasma could be generated via Ohkawa current drive with 3 MW of 28 GHz EBW power. In addition, synergy between EBWCD and bootstrap current may result in a 10% enhancement in current-drive efficiency with 4 MW of EBW power. Recent dual-polarization EBW radiometry measurements on NSTX confirm that efficient coupling to EBWs can be readily accomplished by launching elliptically polarized electromagnetic waves oblique to the confining magnetic field, in agreement with numerical modeling. Plans are being developed for implementing a 1 MW, 28 GHz proof-of-principle EBWCD system on NSTX to test the EBW coupling, heating and current-drive physics at high radio-frequency power densities
Simulation of microtearing turbulence in national spherical torus experiment
Energy Technology Data Exchange (ETDEWEB)
Guttenfelder, W.; Kaye, S. M.; Bell, R. E.; Hammett, G. W.; LeBlanc, B. P.; Mikkelsen, D. R.; Ren, Y. [Princeton Plasma Physics Laboratory, Princeton New Jersey 08543 (United States); Candy, J. [General Atomics, San Diego, California 92186 (United States); Nevins, W. M.; Wang, E. [Lawrence Livermore National Laboratory, Livermore, California 04551 (United States); Zhang, J.; Crocker, N. A. [University of California Los Angeles, California 90095 (United States); Yuh, H. [Nova Photonics Inc., Princeton, New Jersey 08540 (United States)
2012-05-15
Thermal energy confinement times in National Spherical Torus Experiment (NSTX) dimensionless parameter scans increase with decreasing collisionality. While ion thermal transport is neoclassical, the source of anomalous electron thermal transport in these discharges remains unclear, leading to considerable uncertainty when extrapolating to future spherical tokamak (ST) devices at much lower collisionality. Linear gyrokinetic simulations find microtearing modes to be unstable in high collisionality discharges. First non-linear gyrokinetic simulations of microtearing turbulence in NSTX show they can yield experimental levels of transport. Magnetic flutter is responsible for almost all the transport ({approx}98%), perturbed field line trajectories are globally stochastic, and a test particle stochastic transport model agrees to within 25% of the simulated transport. Most significantly, microtearing transport is predicted to increase with electron collisionality, consistent with the observed NSTX confinement scaling. While this suggests microtearing modes may be the source of electron thermal transport, the predictions are also very sensitive to electron temperature gradient, indicating the scaling of the instability threshold is important. In addition, microtearing turbulence is susceptible to suppression via sheared E Multiplication-Sign B flows as experimental values of E Multiplication-Sign B shear (comparable to the linear growth rates) dramatically reduce the transport below experimental values. Refinements in numerical resolution and physics model assumptions are expected to minimize the apparent discrepancy. In cases where the predicted transport is strong, calculations suggest that a proposed polarimetry diagnostic may be sensitive to the magnetic perturbations associated with the unique structure of microtearing turbulence.
Physics and engineering assessments of spherical torus component test facility
International Nuclear Information System (INIS)
Peng, Y.-K.M.; Neumeyer, C.A.; Kessel, C.; Rutherford, P.; Mikkelsen, D.; Bell, R.; Menard, J.; Gates, D.; Schmidt, J.; Synakowski, E.; Grisham, L.; Fogarty, P.J.; Strickler, D.J.; Burgess, T.W.; Tsai, J.; Nelson, B.E.; Sabbagh, S.; Mitarai, O.; Cheng, E.T.; El-Guebaly, L.
2005-01-01
A broadly based study of the fusion engineering and plasma science conditions of a Component Test Facility (CTF), using the Spherical Torus or Spherical Tokamak (ST) configuration, have been carried out. The chamber systems testing conditions in a CTF are characterized by high fusion neutron fluxes Γ n > 4.4x10 13 n/s/cm 2 , over size scales > 10 5 cm 2 and depth scales > 50 cm, delivering > 3 accumulated displacement per atom (dpa) per year. The desired chamber conditions can be provided by a CTF with R 0 1.2 m, A = 1.5, elongation ∼ 3.2, I p ∼ 9 MA, B T ∼ 2.5 T, producing a driven fusion burn using 36 MW of combined neutral beam and RF power. Relatively robust ST plasma conditions are adequate, which have been shown achievable [4] without active feedback manipulation of the MHD modes. The ST CTF will test the single-turn, copper alloy center leg for the toroidal field coil without an induction solenoid and neutron shielding, and require physics data on solenoid-free plasma current initiation, ramp-up, and sustainment to multiple MA level. A new systems code that combines the key required plasma and engineering science conditions of CTF has been prepared and utilized as part of this study. The results show high potential for a family of lowercost CTF devices to suit a variety of fusion engineering science test missions. (author)
Internal transport barriers in the National Spherical Torus Experimenta)
Yuh, H. Y.; Levinton, F. M.; Bell, R. E.; Hosea, J. C.; Kaye, S. M.; LeBlanc, B. P.; Mazzucato, E.; Peterson, J. L.; Smith, D. R.; Candy, J.; Waltz, R. E.; Domier, C. W.; Luhmann, N. C.; Lee, W.; Park, H. K.
2009-05-01
In the National Spherical Torus Experiment [M. Ono et al., Nucl. Fusion 41, 1435 (2001)], internal transport barriers (ITBs) are observed in reversed (negative) shear discharges where diffusivities for electron and ion thermal channels and momentum are reduced. While neutral beam heating can produce ITBs in both electron and ion channels, high harmonic fast wave heating can also produce electron ITBs (e-ITBs) under reversed magnetic shear conditions without momentum input. Interestingly, the location of the e-ITB does not necessarily match that of the ion ITB (i-ITB). The e-ITB location correlates best with the magnetic shear minima location determined by motional Stark effect constrained equilibria, whereas the i-ITB location better correlates with the location of maximum E ×B shearing rate. Measured electron temperature gradients in the e-ITB can exceed critical gradients for the onset of electron thermal gradient microinstabilities calculated by linear gyrokinetic codes. A high-k microwave scattering diagnostic shows locally reduced density fluctuations at wave numbers characteristic of electron turbulence for discharges with strongly negative magnetic shear versus weakly negative or positive magnetic shear. Reductions in fluctuation amplitude are found to be correlated with the local value of magnetic shear. These results are consistent with nonlinear gyrokinetic simulations predicting a reduction in electron turbulence under negative magnetic shear conditions despite exceeding critical gradients.
ITER - torus vacuum pumping system remote handling issues
International Nuclear Information System (INIS)
Stringer, J.
1992-11-01
This report describes design issues concerning remote maintenance of the ITER torus vacuum pumping system. Key issues under investigation in this report are bearings for inert gas operation, transporter integration options, cryopump access, gate valve maintenance frequency, tritium effects on materials, turbomolecular pump design, and remote maintenance. Alternative bearing materials are explored for inert gas operation. Encapsulated motors and rotary feedthroughs offer an alternative option where space requirements are restrictive. A number of transporter options are studied. The preferred scheme depends on the shielded reconfigured ducts to prevent streaming and activation of RH (remote handling) equipment. A radiation mapping of the cell is required to evaluate this concept. Valve seal and bellow life are critical issues and need to be evaluated, as they have a direct bearing on the provision of adequate RH equipment to meet scheduled and unscheduled maintenance outages. The limited space on the inboard side of the cryopumps for RH equipment access requires a reconfigured duct and manifold. A modified shielded duct arrangement is proposed, which would provide more access space, reduced activation of components, and the potential for improved valve seal life. Work at Mound Laboratories has shown the adverse effects of tritium on some bearing lubricants. Silicone-based lubricants should be avoided. (11 refs., 2 tabs., 31 figs.)
Tritium systems concepts for the next European torus (NET)
International Nuclear Information System (INIS)
Sood, S.K.; Bagli, K.S.; Busigin, A.; Kveton, O.K.; Dombra, A.H.; Miller, A.I.
1986-09-01
The study deals with the design of the various tritium processing facilities that will be required for the Next European Torus (NET) design. The reference data for the design of the NET Tritium Systems was provided by the NET team. Significant achievements of this study were: (a) Identification of new ways of handling some problems for example: 1) Recovery of tritium from the helium purge of the lithium-ceramic blanket using a novel Adsoprtion and Catalytic Exchange Process, 2) A new way of combining fuel component separation and coolant water detritiation using cryogenic distillation, 3) The use of parasitic refrigeration for the cryogenic isotope separation, 4) Tritium extraction from effluent gas streams at their respective sources, 5) Attempt to eliminate the need for Air Cleanup Systems. (b) Identification of uncertainties, for example: composition of plasma exhaust, required helium purge rate of Li-Pb for tritium recovery, uncertainty in requirements for decontaminating blanket sectors, etc. (c) Review of ways to limit tritium permeation into steam by swamping with hydrogen and to provide quantitative estimates for this permeation
Divertor Heat Flux Reduction and Detachment in the National Spherical Torus eXperiment.
Soukhanovskii, Vsevolod
2007-11-01
Steady-state handling of the heat flux is a critical divertor issue for both the International Thermonuclear Experimental Reactor and spherical torus (ST) devices. Because of an inherently compact divertor, it was thought that ST-based devices might not be able to fully utilize radiative and dissipative divertor techniques based on induced power and momentum loss. However, initial experiments conducted in the National Spherical Torus Experiment in an open geometry horizontal carbon plate divertor using 0.8 MA 2-6 MW NBI-heated lower single null H-mode plasmas at the lower end of elongations κ=1.8-2.4 and triangularities δ=0.45-0.75 demonstrated that high divertor peak heat fluxes, up to 6-10 MW/ m^2, could be reduced by 50-75% using a high-recycling radiative divertor regime with D2 injection. Furthermore, similar reduction was obtained with a partially detached divertor (PDD) at high D2 injection rates, however, it was accompanied by an X-point MARFE that quickly led to confinement degradation. Another approach takes advantage of the ST relation between strong shaping and high performance, and utilizes the poloidal magnetic flux expansion in the divertor region. Up to 60 % reduction in divertor peak heat flux was achieved at similar levels of scrape-off layer power by varying plasma shaping and thereby increasing the outer strike point (OSP) poloidal flux expansion from 4-6 to 18-22. In recent experiments conducted in highly-shaped 1.0-1.2 MA 6 MW NBI heated H-mode plasmas with divertor D2 injection at rates up to 10^22 s-1, a PDD regime with OSP peak heat flux 0.5-1.5 MW/m^2 was obtained without noticeable confinement degradation. Calculations based on a two point scrape-off layer model with parameterized power and momentum losses show that the short parallel connection length at the OSP sets the upper limit on the radiative exhaust channel, and both the impurity radiation and large momentum sink achievable only at high divertor neutral pressures are required
International Nuclear Information System (INIS)
Podesta, M.; Bell, R.E.; Fredrickson, E.D.; Gorelenkov, N.N.; LeBlanc, B.P.; Crocker, N.A.; Kubota, S.; Heidbrink, W.W.; Yuh, H.
2011-01-01
The National Spherical Torus Experiment (NSTX, (Ono et al 2000 Nucl. Fusion 40 557)) routinely operates with neutral beam injection as the primary system for heating and current drive. The resulting fast ion population is super-Alfvenic, with velocities 1 fast /v Alfven < 5. This provides a strong drive for toroidicity-induced Alfven eigenmodes (TAEs). As the discharge evolves, the fast ion population builds up and TAEs exhibit increasing bursts in amplitude and down-chirps in frequency, which eventually lead to a so-called TAE avalanche. Avalanches cause large (∼<30%) fast ion losses over ∼1 ms, as inferred from the neutron rate. The increased fast ion losses correlate with a stronger activity in the TAE band. In addition, it is shown that a n = 1 mode with frequency well below the TAE gap appears in the Fourier spectrum of magnetic fluctuations as a result of non-linear mode coupling between TAEs during avalanche events. The non-linear coupling between modes, which leads to enhanced fast ion transport during avalanches, is investigated.
Energy Technology Data Exchange (ETDEWEB)
Neto, A.C. [Fusion for Energy, 08019 Barcelona (Spain); Stephen, A. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Sartori, F.; Cavinato, M. [Fusion for Energy, 08019 Barcelona (Spain); Farthing, J.W. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Ranz, R.; Saibene, G. [Fusion for Energy, 08019 Barcelona (Spain); Winter, A. [ITER Organization, Route de Vinon-sur-Verdon, CS 90 046, 13067 St. Paul Lez Durance Cedex (France); Arnoux, G. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Alves, D. [Instituto de Plasmas e Fusão Nuclear, Instituto Superior Técnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Blackman, T.; Boboc, A.; Card, P.J.; Dalley, S.; Day, I.E. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); De Tommasi, G. [Consorzio CREATE/Dipartimento di Ingegneria Elettrica e delle Tecnologie dell’Informazione, Università degli Studi di Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); Drewelow, P.; Elsmore, C.; Ivings, E.; Felton, R. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); and others
2015-10-15
The Joint European Torus (JET) is the largest tokamak currently in operation in the world. One of the greatest challenges of JET is the integrated commissioning of all its major plant systems. This is driven, partially, by the size and complexity of its operational infrastructure and also by the fact that, being an international environment, it has to address the issues of integrating, commissioning and maintaining plant systems developed by third parties. The ITER tokamak, now in construction, is a fusion device twice the size of JET and, being a joint effort between the European Union, China, India, Japan, South Korea, the Russian Federation and the USA, it will share on a wider scale all of the JET challenges regarding integration and integrated commissioning of very large and complex plant systems. With the scope of taking advantage from the history and experience of JET, Fusion for Energy (F4E) has worked together with the Culham Centre for Fusion Energy (CCFE), the host and operator of JET, for the provision of ITER relevant user experiences related to the integrated commissioning of the tokamak. This work presents and discusses the main results and the methods that were used to extract and translate the commissioning experience information into ITER requirements.
Analysis of performance improvements for host and GPU interface of the APENet+ 3D Torus network
International Nuclear Information System (INIS)
Ammendola A, R; Biagioni, A; Frezza, O; Lo Cicero, F; Lonardo, A; Paolucci, P S; Rossetti, D; Simula, F; Tosoratto, L; Vicini, P
2014-01-01
APEnet+ is an INFN (Italian Institute for Nuclear Physics) project aiming to develop a custom 3-Dimensional torus interconnect network optimized for hybrid clusters CPU-GPU dedicated to High Performance scientific Computing. The APEnet+ interconnect fabric is built on a FPGA-based PCI-express board with 6 bi-directional off-board links showing 34 Gbps of raw bandwidth per direction, and leverages upon peer-to-peer capabilities of Fermi and Kepler-class NVIDIA GPUs to obtain real zero-copy, GPU-to-GPU low latency transfers. The minimization of APEnet+ transfer latency is achieved through the adoption of RDMA protocol implemented in FPGA with specialized hardware blocks tightly coupled with embedded microprocessor. This architecture provides a high performance low latency offload engine for both trasmit and receive side of data transactions: preliminary results are encouraging, showing 50% of bandwidth increase for large packet size transfers. In this paper we describe the APEnet+ architecture, detailing the hardware implementation and discuss the impact of such RDMA specialized hardware on host interface latency and bandwidth
Analysis of performance improvements for host and GPU interface of the APENet+ 3D Torus network
Ammendola A, R.; Biagioni, A.; Frezza, O.; Lo Cicero, F.; Lonardo, A.; Paolucci, P. S.; Rossetti, D.; Simula, F.; Tosoratto, L.; Vicini, P.
2014-06-01
APEnet+ is an INFN (Italian Institute for Nuclear Physics) project aiming to develop a custom 3-Dimensional torus interconnect network optimized for hybrid clusters CPU-GPU dedicated to High Performance scientific Computing. The APEnet+ interconnect fabric is built on a FPGA-based PCI-express board with 6 bi-directional off-board links showing 34 Gbps of raw bandwidth per direction, and leverages upon peer-to-peer capabilities of Fermi and Kepler-class NVIDIA GPUs to obtain real zero-copy, GPU-to-GPU low latency transfers. The minimization of APEnet+ transfer latency is achieved through the adoption of RDMA protocol implemented in FPGA with specialized hardware blocks tightly coupled with embedded microprocessor. This architecture provides a high performance low latency offload engine for both trasmit and receive side of data transactions: preliminary results are encouraging, showing 50% of bandwidth increase for large packet size transfers. In this paper we describe the APEnet+ architecture, detailing the hardware implementation and discuss the impact of such RDMA specialized hardware on host interface latency and bandwidth.
Analysis of performance improvements for host and GPU interface of the APENet+ 3D Torus network
Energy Technology Data Exchange (ETDEWEB)
Ammendola A, R [INFN Roma II, Via della Ricerca Scientifica 1 – 00133 Roma (Italy); Biagioni, A; Frezza, O; Lo Cicero, F; Lonardo, A; Paolucci, P S; Rossetti, D; Simula, F; Tosoratto, L; Vicini, P [INFN Roma I, P.le Aldo Moro 2 – 00185 Roma (Italy)
2014-06-06
APEnet+ is an INFN (Italian Institute for Nuclear Physics) project aiming to develop a custom 3-Dimensional torus interconnect network optimized for hybrid clusters CPU-GPU dedicated to High Performance scientific Computing. The APEnet+ interconnect fabric is built on a FPGA-based PCI-express board with 6 bi-directional off-board links showing 34 Gbps of raw bandwidth per direction, and leverages upon peer-to-peer capabilities of Fermi and Kepler-class NVIDIA GPUs to obtain real zero-copy, GPU-to-GPU low latency transfers. The minimization of APEnet+ transfer latency is achieved through the adoption of RDMA protocol implemented in FPGA with specialized hardware blocks tightly coupled with embedded microprocessor. This architecture provides a high performance low latency offload engine for both trasmit and receive side of data transactions: preliminary results are encouraging, showing 50% of bandwidth increase for large packet size transfers. In this paper we describe the APEnet+ architecture, detailing the hardware implementation and discuss the impact of such RDMA specialized hardware on host interface latency and bandwidth.
High frequency fast wave results from the CDX-U spherical torus
International Nuclear Information System (INIS)
Kaita, R.; Majeski, R.; Menard, J.
2001-01-01
The Current Drive Experiment-Upgrade (CDX-U) is the first spherical torus (ST) to investigate radio frequency (RF) heating and current drive. To address the concern that large magnetic field line pitch at the outboard midplane of ST's could inhibit successful coupling to the high harmonic fast wave (HHFW), a rotatable, two strap antenna was installed on CDX-U. Parasitic loading and impurity generation were discovered to be weak and nearly independent of antenna phasing and angle over a wide range, and fast wave electron heating has been observed. Plasma densities up to about 10 12 cm -3 were obtained with noninductive startup solely with HHFW. New ST diagnostics under development on CDX-U include a multilayer mirror (MLM) detector to measure ultrasoft X-rays, a twelve spatial point Thomson scattering (TS) system, and an Electron Bernstein Wave (EBW) system for both electron heating and electron temperature measurements. Preliminary experiments with a boron low velocity edge micropellet injector have also been performed, and further studies of its effectiveness for impurity control will be conducted with a variety of spectroscopic and imaging diagnostics on CDX-U. (author)
Beta-limiting MHD Instabilities in Improved-performance NSTX Spherical Torus Plasmas
International Nuclear Information System (INIS)
J.E. Menard; M.G. Bell; R.E. Bell; E.D. Fredrickson D.A. Gates: S.M. Kaye; B.P. LeBlanc; R. Maingi; D. Mueller; S.A. Sabbagh; D. Stutman; C.E. Bush; D.W. Johnson; R. Kaita; H.W. Kugel; R.J. Maqueda; F. Paoletti; S.F Paul; M. Ono; Y.-K.M. Peng; C.H. Skinner; E.J. Synakowski; the NSTX Research Team
2003-01-01
Global magnetohydrodynamic stability limits in the National Spherical Torus Experiment (NSTX) have increased significantly recently due to a combination of device and operational improvements. First, more routine H-mode operation with broadened pressure profiles allows access to higher normalized beta and lower internal inductance. Second, the correction of a poloidal field coil induced error-field has largely eliminated locked tearing modes during normal operation and increased the maximum achievable beta. As a result of these improvements, peak beta values have reached (not simultaneously) β t = 35%, β N = 6.4, N > = 4.5, β N /l i = 10, and β P = 1.4. High β P operation with reduced tearing activity has allowed a doubling of discharge pulse-length to just over 1 second with sustained periods of β N ∼ 6 above the ideal no-wall limit and near the with-wall limit. Details of the β limit scalings and β-limiting instabilities in various operating regimes are described
International Nuclear Information System (INIS)
Podesta, M.; Bell, R.E.; Crocker, N.A.; Fredrickson, E.D.; Gorelenkov, N.N.; Heidbrink, W.W.; Kubota, S.; LeBlanc, B.P.; Yu, H.
2011-01-01
The National Spherical Torus Experiment (NSTX, (M. Ono et al., Nucl. Fusion 40, 557 (2000))) routinely operates with neutral beam injection as the primary system for heating and current drive. The resulting fast ion population is super-Alfvenic, with velocities 1 fast /v Alfven < 5. This provides a strong drive for toroidicity-induced Alfven eigenmodes (TAEs). As the discharge evolves, the fast ion population builds up and TAEs exhibit increasing bursts in amplitude and down-chirps in frequency, which eventually lead to a so-called TAE avalanche. Avalanches cause large (∼<30%) fast ion losses over ∼ 1 ms, as inferred from the neutron rate. The increased fast ion losses correlate with a stronger activity in the TAE band. In addition, it is shown that a n = 1 mode with frequency well below the TAE gap appears in the Fourier spectrum of magnetic fluctuations as a result of non-linear mode coupling between TAEs during avalanche events. The non-linear coupling between modes, which leads to enhanced fast ion transport during avalanches, is investigated.
Energy Technology Data Exchange (ETDEWEB)
Podesta, M; Crocker, N A; Fredrickson, E D; Gorelenkov, N N; Heidbrink, W W; Kubota, S; LeBlanc, B P
2011-04-26
The National Spherical Torus Experiment (NSTX, [M. Ono et al., Nucl. Fusion 40, 557 (2000)]) routinely operates with neutral beam injection as the primary system for heating and current drive. The resulting fast ion population is super-Alfv enic, with velocities 1 < vfast=vAlfven < 5. This provides a strong drive for toroidicity-induced Alfv en eigenmodes (TAEs). As the discharge evolves, the fast ion population builds up and TAEs exhibit increasing bursts in amplitude and down-chirps in frequency, which eventually lead to a so-called TAE avalanche. Avalanches cause large (≤ 30%) fast ion losses over ~ 1 ms, as inferred from the neutron rate. The increased fast ion losses correlate with a stronger activity in the TAE band. In addition, it is shown that a n = 1 mode with frequency well below the TAE gap appears in the Fourier spectrum of magnetic fluctuations as a result of non-linear mode coupling between TAEs during avalanche events. The non-linear coupling between modes, which leads to enhanced fast ion transport during avalanches, is investigated.
High frequency fast wave results from the CDX-U spherical torus
International Nuclear Information System (INIS)
Kaita, R.; Majeski, R.; Menard, J.
1999-01-01
The Current Drive Experiment-Upgrade (CDX-U) is the first spherical torus (ST) to investigate radio frequency (RF) heating and current drive. To address the concern that large magnetic field line pitch at the outboard midplane of ST's could inhibit successful coupling to the high harmonic fast wave (HHFW), a rotatable, two strap antenna was installed on CDX-U. Parasitic loading and impurity generation were discovered to be weak and nearly independent of antenna phasing and angle over a wide range, and fast wave electron heating has been observed. Plasma densities up to about 10 12 cm -3 were obtained with noninductive startup solely with HHFW. New ST diagnostics under development on CDX-U include a multilayer mirror (MLM) detector to measure ultrasoft X-rays, a twelve spatial point Thomson scattering (TS) system, and an Electron Bernstein Wave (EBW) system for both electron heating and electron temperature measurements. Preliminary experiments with a boron low velocity edge micropellet injector have also been performed, and further studies of its effectiveness for impurity control will be conducted with a variety of spectroscopic and imaging diagnostics on CDX-U. (author)
The confinement of dilute populations of beam ions in the national spherical torus experiment
International Nuclear Information System (INIS)
Heidbrink, W.W.; Miah, M.; Darrow, D.; Le Blanc, B.; Medley, S.; Roquemore, A.L.; Cecil, F.E.
2003-01-01
Short ∼3 ms pulses of 80 keV deuterium neutrals are injected at three different tangency radii into the national spherical torus experiment. The confinement is studied as a function of tangency radius, plasma current (between 0.4 and 1.0 MA), and toroidal field (between 2.5 and 5.0 kG). The jump in neutron emission during the pulse is used to infer prompt losses of beam ions. In the absence of MHD, the neutron data show the expected dependences on beam angle and plasma current; the average jump in the neutron signal is 88±39% of the expected jump. The decay of the neutron and neutral particle signals following the blip are compared to the expected classical deceleration to detect losses on a 10 ms timescale. The temporal evolution of these signals are consistent with Coulomb scattering rates, implying an effective beam-ion confinement time > or ∼ 100 ms. The confinement is insensitive to the toroidal field despite large values of ρ∇B/B < or ∼(0.25), so any effects of non-conservation of the adiabatic invariant μ are smaller than the experimental error. (author)
Surface Treatment of a Lithium Limiter for Spherical Torus Plasma Experiments
Energy Technology Data Exchange (ETDEWEB)
Kaita, R.; Majeski, R.; Doerner, R.; Antar, G.; Timberlake, J.; Spaleta, J.; Hoffman, D.; Jones, B.; Munsat, T.; Kugel, H.; Taylor, G.; Stutman, D.; Soukhanovskii, V.; Maingi, R.; Molesa, S.; Efthimion, P.; Menard, J.; Finkenthal, M.; Luckhardt, S.
2001-03-20
The concept of a flowing lithium first wall for a fusion reactor may lead to a significant advance in reactor design, since it could virtually eliminate the concerns with power density and erosion, tritium retention, and cooling associated with solid walls. As part of investigations to determine the feasibility of this approach, plasma interaction questions in a toroidal plasma geometry are being addressed in the Current Drive eXperiment-Upgrade (CDX-U) spherical torus (ST). The first experiments involved a toroidally local lithium limiter (L3). Measurements of pumpout rates indicated that deuterium pumping was greater for the L3 compared to conventional boron carbide limiters. The difference in the pumpout rates between the two limiter types decreased with plasma exposure, but argon glow discharge cleaning was able to restore the pumping effectiveness of the L3. At no point, however, was the extremely low recycling regime reported in previous lithium experiments achieved. This may be due to the much larger lithium surfaces that were exposed to the plasma in the earlier work. The possibility will be studied in the next set of CDX-U experiments, which are to be conducted with a large area, fully toroidal lithium limiter.
Surface Treatment of a Lithium Limiter for Spherical Torus Plasma Experiments
International Nuclear Information System (INIS)
Kaita, R.; Majeski, R.; Doerner, R.; Antar, G.; Timberlake, J.; Spaleta, J.; Hoffman, D.; Jones, B.; Munsat, T.; Kugel, H.; Taylor, G.; Stutman, D.; Soukhanovskii, V.; Maingi, R.; Molesa, S.; Efthimion, P.; Menard, J.; Finkenthal, M.; Luckhardt, S.
2001-01-01
The concept of a flowing lithium first wall for a fusion reactor may lead to a significant advance in reactor design, since it could virtually eliminate the concerns with power density and erosion, tritium retention, and cooling associated with solid walls. As part of investigations to determine the feasibility of this approach, plasma interaction questions in a toroidal plasma geometry are being addressed in the Current Drive eXperiment-Upgrade (CDX-U) spherical torus (ST). The first experiments involved a toroidally local lithium limiter (L3). Measurements of pumpout rates indicated that deuterium pumping was greater for the L3 compared to conventional boron carbide limiters. The difference in the pumpout rates between the two limiter types decreased with plasma exposure, but argon glow discharge cleaning was able to restore the pumping effectiveness of the L3. At no point, however, was the extremely low recycling regime reported in previous lithium experiments achieved. This may be due to the much larger lithium surfaces that were exposed to the plasma in the earlier work. The possibility will be studied in the next set of CDX-U experiments, which are to be conducted with a large area, fully toroidal lithium limiter
Energy Technology Data Exchange (ETDEWEB)
Ren, Y.; Wang, W. X.; LeBlanc, B. P.; Guttenfelder, W.; Kaye, S. M.; Ethier, S.; Mazzucato, E.; Bell, R. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Lee, K. C. [National Fusion Research Institute, Daejeon 305-806 (Korea, Republic of); Domier, C. W. [University of California at Davis, Davis, California 95616 (United States); Smith, D. R. [University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Yuh, H. [Nova Photonics, Inc., Princeton, New Jersey 08540 (United States)
2015-11-15
In this letter, we report the first observation of the fast response of electron-scale turbulence to auxiliary heating cessation in National Spherical Torus eXperiment [Ono et al., Nucl. Fusion 40, 557 (2000)]. The observation was made in a set of RF-heated L-mode plasmas with toroidal magnetic field of 0.55 T and plasma current of 300 kA. It is observed that electron-scale turbulence spectral power (measured with a high-k collective microwave scattering system) decreases significantly following fast cessation of RF heating that occurs in less than 200 μs. The large drop in the turbulence spectral power has a short time delay of about 1–2 ms relative to the RF cessation and happens on a time scale of 0.5–1 ms, much smaller than the energy confinement time of about 10 ms. Power balance analysis shows a factor of about 2 decrease in electron thermal diffusivity after the sudden drop of turbulence spectral power. Measured small changes in equilibrium profiles across the RF cessation are unlikely able to explain this sudden reduction in the measured turbulence and decrease in electron thermal transport, supported by local linear stability analysis and both local and global nonlinear gyrokinetic simulations. The observations imply that nonlocal flux-driven mechanism may be important for the observed turbulence and electron thermal transport.
Kinetic transport properties of a bumpy torus with finite radial ambipolar field
International Nuclear Information System (INIS)
Spong, D.A.; Harris, E.G.; Hedrick, C.L.
1978-04-01
Bumpy torus neoclassical transport coefficients have been calculted including finite values of the radial ambipolar field. These are obtained by solving a bounce-averaged drift kinetic equation in a local approximation for perturbations in the distribution function (away from a stationary Maxwellian) caused by toroidicity and radial gradients in plasma density, temperature, and potential. Particle and energy fluxes along with the associated transport coefficients are then calculated by taking appropriate moments of the distribution function. Particle orbits are treated by breaking them up into a vertical drift component (due to toroidicity) and a theta precessional drift (as a result of Vector E x Vector B and drifts due to the bumpy toroidal field). The kinetic equation has been solved using both a functional expansion method and finite difference techniques [Alternating-Direction-Implicit (ADI)]. The resulting transport coefficients exhibit a strong dependence on the ambipolar electric field and plasma collisionality. In the large electric field limit, our results are in close agreement with the earlier work of Kovrizhnykh
Comparative study of the electron density profiles in the compact torus plasma merging experiments
International Nuclear Information System (INIS)
Hayashiya, Hitoshi; Asaka, Takeo; Katsurai, Makoto
2003-01-01
Following two previous papers on the comparative studies of the electron density distributions for a single compact torus (CT) and a spherical tokamak (ST), and for the a single ST and a merged ST, a comparative study on the dynamics of the electron density profile and after the CT and ST plasma merging process was performed. The sharpness of the peak in the electron density profile around the mid-plane just after the merging of CT with a low safety factor (q value) such as RFP or spheromak is found to be related to the speed of the magnetic axis during the plasma merging process. It is also found that the electron density gradient near the plasma edge in a high q ST is larger than that of a low q CT. High q ST is found to be provided with the magnetic structure which is able to sustain a large thermal pressure by a strong j x B force. Despite these differences in the electron density profile between CT and ST during merging, the confinement characteristics evaluated from the number of electrons confined within the magnetic separatrix after the completion of the merging is almost similar between in the merging CT and in the merging ST. For all configurations, the electron density profiles after the completion of the merging are analogous to those of the corresponding single configuration produced without the merging process. (author)
Operational Regimes of the National Spherical Torus Experiment; TOPICAL
International Nuclear Information System (INIS)
D. Mueller; M.G. Bell; R.E. Bell; M. Bitter; T. Bigelow; P. Bonoli; M. Carter; J. Ferron; E. Fredrickson; D. Gates; L. Grisham; J.C. Hosea; D. Johnson; R. Kaita; S.M. Kaye; H. Kugel; B.P. LeBlanc; R. Maingi; R. Majeski; R. Maqueda; J. Menard; M. Ono; F. Paoletti; S. Paul; C.K. Phillips; R. Pinsker; R. Raman; S.A. Sabbagh; C.H. Skinner; V.A. Soukhanovskii; D. Stutman; D. Swain; Y. Takase; J. Wilgen; J.R. Wilson; G.A. Wurden; S. Zweben
2002-01-01
The National Spherical Torus Experiment (NSTX) is a proof-of-principle experiment designed to study the physics of Spherical Tori (ST), i.e., low-aspect-ratio toroidal plasmas. Important issues for ST research are whether the high-eta stability and reduced transport theoretically predicted for this configuration can be realized experimentally. In NSTX, the commissioning of a digital real-time plasma control system, the provision of flexible heating systems, and the application of wall conditioning techniques were instrumental in achieving routine operation with good confinement. NSTX has produced plasmas with R/a(approx) 0.85 m/0.68 m, A(approx) 1.25, Ip* 1.1 MA, BT= 0.3-0.45 T, k* 2.2, d* 0.5, with auxiliary heating by up to 4 MW of High Harmonic Fast Waves, and 5 MW of 80 keV D0 Neutral Beam Injection (NBI). The energy confinement time in plasmas heated by NBI has exceeded 100 ms and a toroidal beta (bT= 2m0 and lt;p and gt;/BT02, where BT0 is the central vacuum toroidal magnetic field) up to 22% has be en achieved. HHFW power of 2.3 MW has increased the electron temperature from an initial 0.4 keV to 0.9 keV both with and without producing a significant density rise in the plasma. The early application of both NBI and HHFW heating has slowed the penetration of the inductively produced plasma current, modifying the current profile and, thereby, the observed MHD stability
Operational Regimes of the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Mueller, D.; Bell, M.G.; Bell, R.E.; Bitter, M.; Bigelow, T.; Bonoli, P.; Carter, M.; Ferron, J.; Fredrickson, E.; Gates, D.; Grisham, L.; Hosea, J.C.; Johnson, D.; Kaita, R.; Kaye, S.M.; Kugel, H.; LeBlanc, B.P.; Maingi, R.; Majeski, R.; Maqueda, R.; Menard, J.; Ono, M.; Paoletti, F.; Paul, S.; Phillips, C.K.; Pinsker, R.; Raman, R.; Sabbagh, S.A.; Skinner, C.H.; Soukhanovskii, V.A; Stutman, D.; Swain, D.; Takase, Y.; Wilgen, J.; Wilson, J.R.; Wurden, G.A.; Zweben, S.
2002-01-01
The National Spherical Torus Experiment (NSTX) is a proof-of-principle experiment designed to study the physics of Spherical Tori (ST), i.e., low-aspect-ratio toroidal plasmas. Important issues for ST research are whether the high-eta stability and reduced transport theoretically predicted for this configuration can be realized experimentally. In NSTX, the commissioning of a digital real-time plasma control system, the provision of flexible heating systems, and the application of wall conditioning techniques were instrumental in achieving routine operation with good confinement. NSTX has produced plasmas with R/a ∼ 0.85 m/0.68 m, A ∼ 1.25, Ip * 1.1 MA, BT = 0.3-0.45 T, k * 2.2, d * 0.5, with auxiliary heating by up to 4 MW of High Harmonic Fast Waves, and 5 MW of 80 keV D0 Neutral Beam Injection (NBI). The energy confinement time in plasmas heated by NBI has exceeded 100 ms and a toroidal beta (bT = 2m0 /BT02, where BT0 is the central vacuum toroidal magnetic field) up to 22% has be en achieved. HHFW power of 2.3 MW has increased the electron temperature from an initial 0.4 keV to 0.9 keV both with and without producing a significant density rise in the plasma. The early application of both NBI and HHFW heating has slowed the penetration of the inductively produced plasma current, modifying the current profile and, thereby, the observed MHD stability
Vortex flow in a torus - a method for arc stabilization
International Nuclear Information System (INIS)
Polman, R.W.
1976-08-01
Experiments on ring vortices inside a torus and experiments on semi-toroidal arcs stabilized by such vortices are described. The studies were performed in two separate devices. One of the toroidal vortex chambers - 'Cogion', with R = 0.45 m and r = 0.10 m - permits the establishment of a gas flow only. In the other device - 'Tovorex', with R = 0.19 m and r = 0.04 m - it is also possible to draw a semi-toroidal arc. The measurements surprisingly show that it is possible to describe the radial distribution of the poloidal flow in terms of a plane turbulent wall jet discharging in an external stream. The velocity profile and the growth of the width of the jet are in accordance with experimental data on this subject. A different behaviour is found for the decay of the maximum velocity. The core of the flow proves to be almost stagnant; the axis of rotation is displaced outwardly with respect to the centre of the cross-section over a distance of 6 mm. In 'Tovorex' information about the rotating flow is obtained without the presence of an arc in the vortex core. The velocity profiles prove to be independent of the pressure (50-400 Torr). For experiments with arcs nitrogen is used. It has been found that the semi-toroidal DC-arc, surrounded by a continuous metal wall can be stabilized by the toroidal vortices in the experimental range30 -1 , 0.6 -1 , depends on the current and on the pressure and is independent of Usub(j) and a. Temperatures of the discharge are estimated at approximately 6000 K. The velocity profiles in both vortex chambers are obtained with a hot-wire anemometer operated at constant resistance
Long Term Monitoring of the Io Plasma Torus During the Galileo Encounter
Brown, Michael E.
2002-01-01
In the fall of 1999, the Galileo spacecraft made four passes into the Io plasma torus, obtaining the best in situ measurements ever of the particle and field environment in this densest region of the Jovian magnetosphere. Supporting observations from the ground are vital for understanding the global and temporal context of the in situ observations. We conducted a three-month-long Io plasma torus monitoring campaign centered on the time of the Galileo plasma torus passes to support this aspect of the Galileo mission. The almost-daily plasma density and temperature measurements obtained from our campaign allow the much more sparse but also much more detailed Galileo data to be used to address the issues of the structure of the Io plasma torus, the stability mechanism of the Jovian magnetosphere, the transport of material from the source region near Io, and the nature and source of persistent longitudinal variations. Combining the ground-based monitoring data with the detailed in situ data offers the only possibility for answering some of the most fundamental questions about the nature of the Io plasma torus.
Effect of torus wall flexibility on hydro-structural interaction in BWR containment system
International Nuclear Information System (INIS)
Lu, S.C.H.; McCauley, E.W.; Holman, G.S.
1979-01-01
The MARK I boiling water reactor (BWR) containment system is comprised of a light-bulb-shaped reactor compartment connected through vent pipes to a torus-shaped and partially water-filled pressure suppression chamber, or the wetwell. During either a normally occurring safety relief valve (SRV) discharge or a hypothetical loss-of-coolant accident (LOCA), air or steam is forced into the wetwell water pool for condensation and results in hydrodynamically induced loads on the torus shell. An analytical program is described which employs the finite element method to investigate the influence of torus wall flexibility on hydrodynamically induced pressure and the resultant force on the torus shell surface. The shell flexibility is characterized by the diameter-to-thickness ratio which is varied from the perfectly rigid case to the nominal plant condition. The general conclusion reached is that torus wall flexibility decreases both the maximum pressure seen by the shell wall and the total vertical load resulted from the hydrodynamically induced pressure
Success and failure of the plasma analogy for Laughlin states on a torus
Fremling, Mikael
2017-01-01
We investigate the nature of the plasma analogy for the Laughlin wave function on a torus describing the quantum Hall plateau at ν =\\frac{1}{q} . We first establish, as expected, that the plasma is screening if there are no short nontrivial paths around the torus. We also find that when one of the handles has a short circumference—i.e. the thin-torus limit—the plasma no longer screens. To quantify this we compute the normalization of the Laughlin state, both numerically and analytically. In the thin torus limit, the analytical form of the normalization simplify and we can reconstruct the normalization and analytically extend it back into the 2D regime. We find that there are geometry dependent corrections to the normalization, and this in turn implies that the plasma in the plasma analogy is not screening when in the thin torus limit. Despite the breaking of the plasma analogy in this limit, the analytical approximation is still a good description of the normalization for all tori, and also allows us to compute hall viscosity at intermediate thickness.
A time-dependent anisotropic plasma chemistry model of the Io plasma torus
Arridge, C. S.
2016-12-01
The physics of the Io plasma torus is typically modelled using one box neutral-plasma chemistry models, often referred to as neutral cloud theory models (e.g., Barbosa 1994; Delamere and Bagenal 2003). These models incorporate electron impact and photoionisation, charge exchange, molecular dissociation/recombination reactions, atomic radiatiative losses and Coulomb collisional heating. Isotropic Maxwellian distributions are usually assumed in the implementation of these models. Observationally a population of suprathermal electrons has been identified in the plasma torus and theoretically they have been shown to be important in reproducing the observed ionisation balance in the torus (e.g., Barbosa 1994). In this paper we describe an anisotropic plasma chemistry model for the Io torus that is inspired by ion cyclotron wave observations (Huddleston et al. 1994; Leisner et al. 2011), ion anisotropies due to pick up (Wilson et al. 2008), and theoretical ideas on the maintenance of the suprathermal electron population (Barbosa 1994). We present both steady state calculations and also time varying solutions (e.g., Delamere et al. 2004) where increases in the neutral source rate in the torus generates perturbations in ion anisotropies that subsequently decay over a timescale much longer than the duration of the initial perturbation. We also present a method for incorporating uncertainties in reaction rates into the model.
Jet-torus connection in radio galaxies. Relativistic hydrodynamics and synthetic emission
Fromm, C. M.; Perucho, M.; Porth, O.; Younsi, Z.; Ros, E.; Mizuno, Y.; Zensus, J. A.; Rezzolla, L.
2018-01-01
Context. High resolution very long baseline interferometry observations of active galactic nuclei have revealed asymmetric structures in the jets of radio galaxies. These asymmetric structures may be due to internal asymmetries in the jets or they may be induced by the different conditions in the surrounding ambient medium, including the obscuring torus, or a combination of the two. Aims: In this paper we investigate the influence of the ambient medium, including the obscuring torus, on the observed properties of jets from radio galaxies. Methods: We performed special-relativistic hydrodynamic (SRHD) simulations of over-pressured and pressure-matched jets using the special-relativistic hydrodynamics code Ratpenat, which is based on a second-order accurate finite-volume method and an approximate Riemann solver. Using a newly developed radiative transfer code to compute the electromagnetic radiation, we modelled several jets embedded in various ambient medium and torus configurations and subsequently computed the non-thermal emission produced by the jet and thermal absorption from the torus. To better compare the emission simulations with observations we produced synthetic radio maps, taking into account the properties of the observatory. Results: The detailed analysis of our simulations shows that the observed properties such as core shift could be used to distinguish between over-pressured and pressure matched jets. In addition to the properties of the jets, insights into the extent and density of the obscuring torus can be obtained from analyses of the single-dish spectrum and spectral index maps.
A thyristor breaker of 1.5 109 V.A. for the poloidal field system of TORUS SUPRA
International Nuclear Information System (INIS)
Bareyt, B.; Leloup, C.; Rijnoudt, E.
1980-09-01
The poloidal field system of Torus Supra has an inductive storage of approximately 38 MJ, which has conducted to research the best solution for a D.C. breaker (55 kA., 27 kV). A solid-state breaker has been chosen. The working principles have been tested on a small size model. The final circuit breaker will contain a large number of thyristors in series and in parallel; the critical problem lies in the series arrangement. A test unit for full tension has been constructed. In this unit the thyristors are submitted to the maximum current as well as to the maximum voltage. The surges measured during tests are not higher than the calculated values. A synthetic circuit of the poloidal field system has been used for test under the final working conditions
Energy Technology Data Exchange (ETDEWEB)
Peterson, J. L. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States); Bell, R.; Guttenfelder, W.; Hammett, G. W.; Kaye, S. M.; LeBlanc, B.; Mikkelsen, D. R. [Princeton Plasma Physics Laboratory, Princeton University, Princeton, New Jersey 08543 (United States); Candy, J. [General Atomics, San Diego, California 92186 (United States); Smith, D. R. [Department of Engineering Physics, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Yuh, H. Y. [Nova Photonics Inc., Princeton, New Jersey 08540 (United States)
2012-05-15
The National Spherical Torus Experiment (NSTX) [M. Ono et al., Nucl. Fusion 40, 557 (2000)] can achieve high electron plasma confinement regimes that are super-critically unstable to the electron temperature gradient driven (ETG) instability. These plasmas, dubbed electron internal transport barriers (e-ITBs), occur when the magnetic shear becomes strongly negative. Using the gyrokinetic code GYRO [J. Candy and R. E. Waltz, J. Comput. Phys. 186, 545 (2003)], the first nonlinear ETG simulations of NSTX e-ITB plasmas reinforce this observation. Local simulations identify a strongly upshifted nonlinear critical gradient for thermal transport that depends on magnetic shear. Global simulations show e-ITB formation can occur when the magnetic shear becomes strongly negative. While the ETG-driven thermal flux at the outer edge of the barrier is large enough to be experimentally relevant, the turbulence cannot propagate past the barrier into the plasma interior.
Refined large N duality for knots
DEFF Research Database (Denmark)
Kameyama, Masaya; Nawata, Satoshi
We formulate large N duality of U(N) refined Chern-Simons theory with a torus knot/link in S³. By studying refined BPS states in M-theory, we provide the explicit form of low-energy effective actions of Type IIA string theory with D4-branes on the Ω-background. This form enables us to relate...
EDDYMULT: a computing system for solving eddy current problems in a multi-torus system
International Nuclear Information System (INIS)
Nakamura, Yukiharu; Ozeki, Takahisa
1989-03-01
A new computing system EDDYMULT based on the finite element circuit method has been developed to solve actual eddy current problems in a multi-torus system, which consists of many torus-conductors and various kinds of axisymmetric poloidal field coils. The EDDYMULT computing system can deal three-dimensionally with the modal decomposition of eddy current in a multi-torus system, the transient phenomena of eddy current distributions and the resultant magnetic field. Therefore, users can apply the computing system to the solution of the eddy current problems in a tokamak fusion device, such as the design of poloidal field coil power supplies, the mechanical stress design of the intensive electromagnetic loading on device components and the control analysis of plasma position. The present report gives a detailed description of the EDDYMULT system as an user's manual: 1) theory, 2) structure of the code system, 3) input description, 4) problem restrictions, 5) description of the subroutines, etc. (author)
Overview of Results from the National Spherical Torus Experiment (NSTX)
International Nuclear Information System (INIS)
Gates, D.A.; Ahn, J.; Allain, R.; Andre, R.; Bastasz, R.; Bell, M.; Bell, R.; Belova, E.; Berkery, J.; Betti, R.
2009-01-01
The mission of NSTX is the demonstration of the physics basis required to extrapolate to the next steps for the spherical torus (ST), such as a plasma facing component test facility (NHTX) or an ST based component test facility (ST-CTF), and to support ITER. Key issues for the ST are transport, and steady state high β operation. To better understand electron transport, a new high-k scattering diagnostic was used extensively to investigate electron gyro-scale fluctuations with varying electron temperature gradient scale-length. Results from n = 3 braking studies are consistent with the flow shear dependence of ion transport. New results from electron Bernstein wave emission measurements from plasmas with lithium wall coating applied indicate transmission efficiencies near 70% in H-mode as a result of reduced collisionality. Improved coupling of High Harmonic Fast-Waves has been achieved by reducing the edge density relative to the critical density for surface wave coupling. In order to achieve high bootstrap current fraction, future ST designs envision running at very high elongation. Plasmas have been maintained on NSTX at very low internal inductance l i ∼ 0.4 with strong shaping (κ ∼ 2.7, (delta) ∼ 0.8) with β N approaching the with-wall beta limit for several energy confinement times. By operating at lower collisionality in this regime, NSTX has achieved record non-inductive current drive fraction f NI ∼ 71%. Instabilities driven by super-Alfvenic ions will be an important issue for all burning plasmas, including ITER. Fast ions from NBI on NSTX are super-Alfvenic. Linear TAE thresholds and appreciable fast-ion loss during multi-mode bursts are measured and these results are compared to theory. The impact of n > 1 error fields on stability is a important result for ITER. RWM/RFA feedback combined with n=3 error field control was used on NSTX to maintain plasma rotation with β above the no-wall limit. Other highlights are: results of lithium coating
International Nuclear Information System (INIS)
Almeyda, Triana; Robinson, Andrew; Richmond, Michael; Vazquez, Billy; Nikutta, Robert
2017-01-01
The obscuring circumnuclear torus of dusty molecular gas is one of the major components of active galactic nuclei (AGN). The torus can be studied by analyzing the time response of its infrared (IR) dust emission to variations in the AGN continuum luminosity, a technique known as reverberation mapping. The IR response is the convolution of the AGN ultraviolet/optical light curve with a transfer function that contains information about the size, geometry, and structure of the torus. Here, we describe a new computer model that simulates the reverberation response of a clumpy torus. Given an input optical light curve, the code computes the emission of a 3D ensemble of dust clouds as a function of time at selected IR wavelengths, taking into account light travel delays. We present simulated dust emission responses at 3.6, 4.5, and 30 μ m that explore the effects of various geometrical and structural properties, dust cloud orientation, and anisotropy of the illuminating radiation field. We also briefly explore the effects of cloud shadowing (clouds are shielded from the AGN continuum source). Example synthetic light curves have also been generated, using the observed optical light curve of the Seyfert 1 galaxy NGC 6418 as input. The torus response is strongly wavelength-dependent, due to the gradient in cloud surface temperature within the torus, and because the cloud emission is strongly anisotropic at shorter wavelengths. Anisotropic illumination of the torus also significantly modifies the torus response, reducing the lag between the IR and optical variations.
Energy Technology Data Exchange (ETDEWEB)
Almeyda, Triana; Robinson, Andrew; Richmond, Michael; Vazquez, Billy [School of Physics and Astronomy, Rochester Institute of Technology, Rochester, NY 14623 (United States); Nikutta, Robert, E-mail: tra3595@rit.edu [National Optical Astronomy Observatory, 950 N Cherry Ave, Tucson, AZ 85719 (United States)
2017-07-01
The obscuring circumnuclear torus of dusty molecular gas is one of the major components of active galactic nuclei (AGN). The torus can be studied by analyzing the time response of its infrared (IR) dust emission to variations in the AGN continuum luminosity, a technique known as reverberation mapping. The IR response is the convolution of the AGN ultraviolet/optical light curve with a transfer function that contains information about the size, geometry, and structure of the torus. Here, we describe a new computer model that simulates the reverberation response of a clumpy torus. Given an input optical light curve, the code computes the emission of a 3D ensemble of dust clouds as a function of time at selected IR wavelengths, taking into account light travel delays. We present simulated dust emission responses at 3.6, 4.5, and 30 μ m that explore the effects of various geometrical and structural properties, dust cloud orientation, and anisotropy of the illuminating radiation field. We also briefly explore the effects of cloud shadowing (clouds are shielded from the AGN continuum source). Example synthetic light curves have also been generated, using the observed optical light curve of the Seyfert 1 galaxy NGC 6418 as input. The torus response is strongly wavelength-dependent, due to the gradient in cloud surface temperature within the torus, and because the cloud emission is strongly anisotropic at shorter wavelengths. Anisotropic illumination of the torus also significantly modifies the torus response, reducing the lag between the IR and optical variations.
Energy Technology Data Exchange (ETDEWEB)
Ichikawa, Kohei; Ueda, Yoshihiro [Department of Astronomy, Kyoto University, Kitashirakawa-Oiwake-cho, Sakyo-ku, Kyoto 606-8502 (Japan); Packham, Christopher; Lopez-Rodriguez, Enrique; Alsip, Crystal D. [Department of Physics and Astronomy, University of Texas at San Antonio, One UTSA Circle, San Antonio, TX 78249 (United States); Almeida, Cristina Ramos; Ramos, Andrés Asensio; González-Martín, Omaira [Instituto de Astrofísica de Canarias, C/Vía Láctea, s/n, E-38205 La Laguna, Tenerife (Spain); Alonso-Herrero, Almudena [Instituto de Física de Cantabria, CSIC-Universidad de Cantabria, E-39005 Santander (Spain); Díaz-Santos, Tanio [Spitzer Science Center, California Institute of Technology, MS 220-6, Pasadena, CA 91125 (United States); Elitzur, Moshe [Department of Physics and Astronomy, University of Kentucky, Lexington, KY 40506-0055 (United States); Hönig, Sebastian F. [School of Physics and Astronomy, University of Southampton, Southampton SO17 1BJ (United Kingdom); Imanishi, Masatoshi [Subaru Telescope, 650 North A’ohoku Place, Hilo, HI 96720 (United States); Levenson, Nancy A. [Gemini Observatory, Southern Operations Center, c/o AURA, Casilla 603, La Serena (Chile); Mason, Rachel E. [Gemini Observatory, Northern Operations Center, 670 N. A’ohoku Place, Hilo, HI 96720 (United States); Perlman, Eric S., E-mail: ichikawa@kusastro.kyoto-u.ac.jp [Department of Physics and Space Sciences, 150 W. University Blvd., Florida Institute of Technology, Melbourne, FL 32901 (United States)
2015-04-20
We present results from the fitting of infrared (IR) spectral energy distributions of 21 active galactic nuclei (AGNs) with clumpy torus models. We compiled high spatial resolution (∼0.3–0.7 arcsec) mid-IR (MIR) N-band spectroscopy, Q-band imaging, and nuclear near- and MIR photometry from the literature. Combining these nuclear near- and MIR observations, far-IR photometry, and clumpy torus models enables us to put constraints on the torus properties and geometry. We divide the sample into three types according to the broad line region (BLR) properties: type-1s, type-2s with scattered or hidden broad line region (HBLR) previously observed, and type-2s without any published HBLR signature (NHBLR). Comparing the torus model parameters gives us the first quantitative torus geometrical view for each subgroup. We find that NHBLR AGNs have smaller torus opening angles and larger covering factors than HBLR AGNs. This suggests that the chance to observe scattered (polarized) flux from the BLR in NHBLR could be reduced by the dual effects of (a) less scattering medium due to the reduced scattering volume given the small torus opening angle and (b) the increased torus obscuration between the observer and the scattering region. These effects give a reasonable explanation for the lack of observed HBLR in some type-2 AGNs.
The Coulomb gas representation of critical RSOS models on the sphere and the torus
International Nuclear Information System (INIS)
Foda, O.; Nienhuis, B.
1989-01-01
We derive the Coulomb gas formulation of the c<1 discrete unitary series, on the sphere and the torus, starting from the corresponding regime-III RSOS models on a square lattice with appropriate topology. We clarify the origin of the background charge, the screening charges, and the choice of operator representations in a correlation function. In the scaling limit, we obtain a bosonic action coupled to the background curvature in addition to topological terms that vanish on the Riemann sphere. Its Virasoro algebra has the central charge expected on the basis of comparing conformal dimensions. As an application, we derive general expressions for the correlation functions on the torus. (orig.)
The Coulomb gas representation of critical RSOS models on the sphere and the torus
Energy Technology Data Exchange (ETDEWEB)
Foda, O. (Rijksuniversiteit Utrecht (Netherlands). Inst. voor Theoretische Fysica); Nienhuis, B. (Rijksuniversiteit Leiden (Netherlands). Inst. Lorentz voor Theoretische Natuurkunde)
1989-10-02
We derive the Coulomb gas formulation of the c<1 discrete unitary series, on the sphere and the torus, starting from the corresponding regime-III RSOS models on a square lattice with appropriate topology. We clarify the origin of the background charge, the screening charges, and the choice of operator representations in a correlation function. In the scaling limit, we obtain a bosonic action coupled to the background curvature in addition to topological terms that vanish on the Riemann sphere. Its Virasoro algebra has the central charge expected on the basis of comparing conformal dimensions. As an application, we derive general expressions for the correlation functions on the torus. (orig.).
Influence of globalmagnetic perturbations on plasma behavior in Elmo Bumpy Torus
International Nuclear Information System (INIS)
Quon, B.H.; Dandl, R.A.; Colestock, P.L.; Bieniosek, F.M.; Ikegami, H.
1979-02-01
The sensitivity of plasma confinement to magnetic field error effects has been tested experimentally using externally introduced global field errors on the ELMO Bumpy Torus (EBT). Below a critical error field (deltaB/sub r//B)/sub cr/ of approx. = to 0.6-1 x 10 -3 the plasma was observed to be essentially free from convective cells, toroidal currents, and instabilities. This observed critical value is comparable to a neoclassical critical field error (deltaB/sub r//B)/sub cr/ approx. = rho/R, the ratio of the ion Larmor radius to the major radius of the torus
Automatic path-planning for a multilink articulated boom within the torus of a fusion reactor
International Nuclear Information System (INIS)
Smidt, D.
1986-08-01
For in-torus maintenance of fusion machines a manipulator is conveyed to the working area by a multilink-transporter, also called 'articulated boom'. Systems of this type have in general four to five links and move in the midplane of the torus. They are kinematically redundant and have a very restricted working space. In this paper automatic methods for the collision free approach of any position of the final joint within the reach of the transporter are presented, including insertion and removal. By automatic teach-in with the CAD-simulation a table of safe configurations can be generated and supplemented by a fine-positioning algorithm. (orig.) [de
Low-Gain Circularly Polarized Antenna with Torus-Shaped Pattern
Amaro, Luis R.; Kruid, Ronald C.; Vacchione, Joseph D.; Prata, Aluizio
2012-01-01
The Juno mission to Jupiter requires an antenna with a torus-shaped antenna pattern with approximately 6 dBic gain and circular polarization over the Deep Space Network (DSN) 7-GHz transmit frequency and the 8-GHz receive frequency. Given the large distances that accumulate en-route to Jupiter and the limited power afforded by the solar-powered vehicle, this toroidal low-gain antenna requires as much gain as possible while maintaining a beam width that could facilitate a +/-10deg edge of coverage. The natural antenna that produces a toroidal antenna pattern is the dipole, but the limited approx. = 2.2 dB peak gain would be insufficient. Here a shaped variation of the standard bicone antenna is proposed that could achieve the required gains and bandwidths while maintaining a size that was not excessive. The final geometry that was settled on consisted of a corrugated, shaped bicone, which is fed by a WR112 waveguide-to-coaxial- waveguide transition. This toroidal low-gain antenna (TLGA) geometry produced the requisite gain, moderate sidelobes, and the torus-shaped antenna pattern while maintaining a very good match over the entire required frequency range. Its "horn" geometry is also low-loss and capable of handling higher powers with large margins against multipactor breakdown. The final requirement for the antenna was to link with the DSN with circular polarization. A four-layer meander-line array polarizer was implemented; an approach that was fairly well suited to the TLGA geometry. The principal development of this work was to adapt the standard linear bicone such that its aperture could be increased in order to increase the available gain of the antenna. As one increases the aperture of a standard bicone, the phase variation across the aperture begins to increase, so the larger the aperture becomes, the greater the phase variation. In order to maximize the gain from any aperture antenna, the phase should be kept as uniform as possible. Thus, as the standard
International Nuclear Information System (INIS)
Gates, D.A.
2003-01-01
Long-pulse, high-beta scenarios have been established on the National Spherical Torus Experiment (NSTX). Beta(sub)t(always equal to 2μ(sub)0· /B 2 (sub)t0) ∼ 35% has been achieved during transient discharges. The machine improvements that lead to these results, including error field reduction and high-temperature bakeout of plasma-facing components are described. The highest Beta(sub)t plasmas have high triangularity (delta = 0.8) and elongation (k = 2.0) at low-aspect ratio A always equal to R/a = 1.4. The strong shaping permits large values of normalized current, I(sub)N(always equal to I(sub)p /(aB(sub)t0)) approximately equal to 6 while maintaining moderate values of q(sub)95 = 4. Long-pulse discharges up to 1 sec in duration have been achieved with substantial bootstrap current. The total noninductive current drive can be as high as 60%, comprised of 50% bootstrap current and ∼10% neutral-beam current drive. The confinement enhancement factor H89P is in excess of 2.7. Beta(sub)N * H(sub)89P approximately or greater than 15 has been maintained for 8 * tau(sub)E ∼ 1.6 * tau(sub)CR, where tau(sub)CR is the relaxation time of the first radial moment of the toroidal current density. The ion temperature for these plasmas is significantly higher than that predicted by neoclassical theory
A three-barrel repeating pneumatic pellet injector for plasma fueling of the Joint European Torus
International Nuclear Information System (INIS)
Combs, S.K.; Milora, S.L.; Baylor, L.R.; Foust, C.R.; Gethers, F.E.; Sparks, D.O.
1987-01-01
Pellet fueling, the injection of frozen hydrogen isotope pellets at high velocity, has been used to improve plasma performance in various tokamak experiments. In one recent experiment, the repeating pneumatic hydrogen pellet injector was used on the Tokamak Fusion Test Reactor (TFTR). This machine gun-like device, which was developed at the Oak Ridge National Laboratory (ORNL) with an objective of steady-state fueling applications, was characterized by a fixed pellet size and a maximum repetition rate of 4 to 6 Hz for several seconds. It was used to deliver deuterium pellets at speeds ranging from 1.0 to 1.5 km/s into TFTR plasma discharges. In the first experiments, injection of single, large (nominal 4-mm-diam) pellets provided high plasma densities in TFTR (1.8 x 10 14 cm -3 on axis). After a conversion to smaller (nominal 2.7-mm-diam) pellets, the pellet injector was operated in the repeating mode to gradually increase the plasma density, injecting up to five pellets on a single machine pulse. This resulted in central plasma densities approaching 4 x 10 14 cm -3 and n tau values of 1.4 x 10 14 cm -3 s. For plasma fueling applications on the Joint European Torus (JET), a pellet injector fashioned after the prototype repeating pneumatic design has been developed. The versatile injector features three repeating guns in a common vacuum enclosure; the guns provide pellets that are 2.7, 4.0, and 6.0 mm in diameter and can operate independently at repetition rates of 5, 2.5, and 1 Hz, respectively. The injector has been installed on JET. A description of the equipment is presented, emphasizing the differences from the original repeating device. Performance characteristics of the three pneumatic guns are also included
International Nuclear Information System (INIS)
Paris, P.J.; Yassen, F.; Assis, A.S. de; Raposo, C.
1988-07-01
The development of controlled thermonuclear reaction in TOKAMAK type reactors, and the main projects in the world are presented. The main characteristics of the JET (Joint European Torus) program, the perspectives for energy production, and the international cooperation for viable use of the TOKAMAK are analysed. (M.C.K.) [pt
Energy Technology Data Exchange (ETDEWEB)
Morrison, David R., E-mail: drm@physics.ucsb.edu [Departments of Mathematics and Physics, U.C. Santa Barbara, Santa Barbara, CA 93106 (United States); Ronen Plesser, M. [Center for Geometry and Theoretical Physics, Duke University, Durham NC 27708 (United States)
2015-09-15
For complete intersection Calabi–Yau manifolds in toric varieties, Gross and Haase–Zharkov have given a conjectural combinatorial description of the special Lagrangian torus fibrations whose existence was predicted by Strominger, Yau and Zaslow. We present a geometric version of this construction, generalizing an earlier conjecture of the first author.
Ruan, Wei-Dong
2004-01-01
This paper is the sequel to my recent paper [10]. It will provide technical details of our gradient flow construction and related problems, which are essential for our construction of Lagrangian torus fibrations in [10] and subsequent papers [11, 13, 14].
Edge fluctuations in the MST [Madison Symmetric Torus] reversed field pinch
International Nuclear Information System (INIS)
Almagri, A.; Assadi, S.; Beckstead, J.; Chartas, G.; Crocker, N.; Den Hartog, D.; Dexter, R.; Hokin, S.; Holly, D.; Nilles, E.; Prager, S.; Rempel, T.; Sarff, J.; Scime, E.; Shen, W.; Spragins, C.; Sprott, J.; Starr, G.; Stoneking, M.; Watts, C.
1990-10-01
Edge magnetic and electrostatic fluctuations are measured in the Madison Symmetric Torus (MST) reversed field pinch. At low frequency ( e > p e /p e where φ and p e are the fluctuating potential and pressure, respectively). From measurements of the fluctuating density, temperature, and potential we infer that the electrostatic fluctuation induced transport of particles and energy can be substantial. 13 refs., 11 figs
The European Communities (Privileges of the Joint European Torus) Order 1978 (S.I. no. 1033)
International Nuclear Information System (INIS)
1978-01-01
This Order confers privileges on the Joint European Torus, as required by Decision 78/472/Euratom of 30 May 1978 of the Council of the European Communities and by the Exchange of Letters of 3 May 1978 between the Government of the United Kingdom and the European Atomic Energy Community [fr
Equilibrium and stability of high-beta plasma in Modified Bumpy Torus (MBT)
International Nuclear Information System (INIS)
Todoroki, J.; Shiina, S.; Saito, K.; Osanai, Y.; Nogi, Y.; Gesso, H.; Yagi, I.; Yokoyama, K.; Yoshimura, H.; Nihon Univ., Tokyo. Atomic Energy Research Inst.)
1977-01-01
The equilibrium and stability properties of the plasma in Modified Bumpy Torus, which is an asymmetric system with closed magnetic lines of force, is reported. For small beta value, the growth rate of m=1 mode instability in MBT can be smaller than that of Scyllac configuration. The results of 1/4 toroidal sector experiment are reported. (author)
Demonstration of direct energy recovery of full energy ions at 40 keV on a PLT/ISX beam system
International Nuclear Information System (INIS)
Stirling, W.L.; Barber, G.C.; Dagenhart, W.K.
1980-01-01
The desire for multisecond beams in the 80-keV/nucleon energy range at 10 MW/module has emphasized the need for technological advances in several areas. At such beam energies, as much as 75% of the initial beam energy is retained in the unneutralized ion components. As a result, two questions immediately come to mind: how can one dispose of this energy; or better still, how can one efficiently recover this energy. The conventional way of treating such a problem is to deflect the ions out of the neutral beam and onto water-cooled plates or beam dumps. This method has worked satisfactorily for 40-keV/nucleon beams in excess of 1.5 MW and approx. 0.5 s. However, the power per unit area to be disposed of in the high power, multisecond beams mentioned above is beyond present-day technology. We have proposed and demonstrated a unique solution to this problem which not only removes the need for beam dumps but also returns from 50 to 80% of the energy contained in the full energy ion component directly and dynamically to the high voltage supply. In fact, the energy in the residual ion component is not expended. The tests were made on a PLT/ISX type beam line at 40 keV/nucleon of about 800 kW and 0.1 s
Breiding, Peter; Georganopoulos, Markos; Meyer, Eileen T.
2018-01-01
Recent multiwavelength work led by the Boston University blazar group (e.g., Marscher et al.) strongly suggests that a fraction of the blazar flares seen by the Fermi Large Area Telescope (LAT) take place a few to several pc away from the central engine. However, at such distances from the central engine, there is no adequate external photon field to provide the seed photons required for producing the observed GeV emission under leptonic inverse Compton (IC) models. A possible solution is a spine-sheath geometry for the emitting region (MacDonald et al., but see Nalewajko et al.). Here we use the current view of the molecular torus (e.g., Elitzur; Netzer), in which the torus extends a few pc beyond the dust sublimation radius with dust clouds distributed with a declining density for decreasing polar angle. We show that for a spine-sheath blazar jet embedded in the torus, the wide beaming pattern of the synchrotron radiation of the relatively slow sheath will heat molecular clouds with subsequent IR radiation that will be highly boosted in the spine comoving frame, and that under reasonable conditions this photon field can dominate over the sheath photons directly entering the spine. If the sheath is sufficiently luminous it will sublimate the dust, and if the sheath synchrotron radiation extends to optical-UV energies (as may happen during flares), this will illuminate the sublimated dust clouds to produce emission lines that will vary in unison with the optical-UV continuum, as has been very recently reported for blazar CTA 102 (Jorstad et al.).
Sahai, R; Vlemmings, W H T; Gledhill, T; Sánchez Contreras, C; Lagadec, E; Nyman, L-Å; Quintana-Lacaci, G
2017-01-20
We have mapped 12 CO J=3-2 and other molecular lines from the "water-fountain" bipolar pre-planetary nebula (PPN) IRAS 16342-3814 with [Formula: see text] resolution using ALMA. We find (i) two very high-speed knotty, jet-like molecular outflows, (ii) a central high-density (> few × 10 6 cm -3 ), expanding torus of diameter 1300 AU, and (iii) the circumstellar envelope of the progenitor AGB, generated by a sudden, very large increase in the mass-loss rate to > 3.5 × 10 -4 M ⊙ yr -1 in the past ~455 yr. Strong continuum emission at 0.89 mm from a central source (690 mJy), if due to thermally-emitting dust, implies a substantial mass (0.017 M ⊙ ) of very large (~mm-sized) grains. The measured expansion ages of the above structural components imply that the torus (age~160 yr) and the younger high-velocity outflow (age~110 yr) were formed soon after the sharp increase in the AGB mass-loss rate. Assuming a binary model for the jets in IRAS 16342, the high momentum rate for the dominant jet-outflow in IRAS 16342 implies a high minimum accretion rate, ruling out standard Bondi-Hoyle-Lyttleton wind accretion and wind Roche lobe overflow (RLOF) models with white-dwarf or main-sequence companions. Most likely, enhanced RLOF from the primary or accretion modes operating within common envelope evolution are needed.
Riemann-Hilbert treatment of Liouville theory on the torus: the general case
International Nuclear Information System (INIS)
Menotti, Pietro
2011-01-01
We extend the previous treatment of Liouville theory on the torus to the general case in which the distribution of charges is not necessarily symmetric. This requires the concept of Fuchsian differential equation on Riemann surfaces. We show through a group theoretic argument that the Heun parameter and a weight constant are sufficient to satisfy all monodromy conditions. We then apply the technique of differential equations on a Riemann surface to the two-point function on the torus in which one source is arbitrary and the other small. As a byproduct, we give in terms of quadratures the exact Green function on the square and on the rhombus with opening angle 2π/6 in the background of the field generated by an arbitrary charge.
On the location of the Io plasma torus: Voyager 1 observations
Directory of Open Access Journals (Sweden)
M. Volwerk
2018-06-01
Full Text Available The Voyager 1 outbound ultraviolet observations of the Io plasma torus are used to determine the location of the ansae, to obtain a third viewing angle of this structure in the Jovian magnetosphere. At an angle of −114° with respect to the Sun–Jupiter line, or a Jovian local time of 04:30 LT, the Voyager 1 data deliver a distance of 5.74±0.10 RJ for the approaching and 5.83±0.15 RJ for the receding ansa. Various periodicities in the radial distance, brightness and width of the ansae are seen with respect to system III longitude and Io phase angle. The torus ribbon feature does not appear in all ansa scans.
Lagrange multiplier and Wess-Zumino variable as extra dimensions in the torus universe
Nejad, Salman Abarghouei; Dehghani, Mehdi; Monemzadeh, Majid
2018-01-01
We study the effect of the simplest geometry which is imposed via the topology of the universe by gauging non-relativistic particle model on torus and 3-torus with the help of symplectic formalism of constrained systems. Also, we obtain generators of gauge transformations for gauged models. Extracting corresponding Poisson structure of existed constraints, we show the effect of the shape of the universe on canonical structure of phase-spaces of models and suggest some phenomenology to prove the topology of the universe and probable non-commutative structure of the space. In addition, we show that the number of extra dimensions in the phase-spaces of gauged embedded models are exactly two. Moreover, in classical form, we talk over modification of Newton's second law in order to study the origin of the terms appeared in the gauged theory.
Energy Technology Data Exchange (ETDEWEB)
Smith, D. R.; Fonck, R. J.; McKee, G. R.; Thompson, D. S. [Department of Engineering Physics, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Bell, R. E.; Diallo, A.; Guttenfelder, W.; Kaye, S. M.; LeBlanc, B. P.; Podesta, M. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States)
2013-05-15
The spherical torus edge region is among the most challenging regimes for plasma turbulence simulations. Here, we measure the spatial and temporal properties of ion-scale turbulence in the steep gradient region of H-mode pedestals during edge localized mode-free, MHD quiescent periods in the National Spherical Torus Experiment. Poloidal correlation lengths are about 10 ρ{sub i}, and decorrelation times are about 5 a/c{sub s}. Next, we introduce a model aggregation technique to identify parametric dependencies among turbulence quantities and transport-relevant plasma parameters. The parametric dependencies show the most agreement with transport driven by trapped-electron mode, kinetic ballooning mode, and microtearing mode turbulence, and the least agreement with ion temperature gradient turbulence. In addition, the parametric dependencies are consistent with turbulence regulation by flow shear and the empirical relationship between wider pedestals and larger turbulent structures.
Characteristics and performance of a superconducting bumpy-torus magnet facility for plasma research
Roth, J. R.; Holmes, A. D.; Keller, T. A.; Krawczonek, W. M.
1973-01-01
The NASA Lewis bumpy-torus facility consists of 12 superconducting coils, each 19 cm i.d. and capable of 3.0 T on its axis. The coils are equally spaced around a toroidal array with a major diameter of 1.52 m; they are mounted with the major axis of the torus vertical in a single vacuum tank 2.6 m in diameter. Tests of the facility mapped out its magnetic, cryogenic, vacuum, mechanical, and electrical performance. The design value of the maximum magnetic field on the magnetic axis, 3.0 T, was reached and exceeded. A maximum magnetic field of 3.23 T was held for a period of 60 minutes. When the coils were charged to a maximum magnetic field of 3.35 T, the coil system went normal without apparent damage or degradation of performance.
Elmo Bumpy Torus proof of principle, Phase II: Title 1 report. Volume IX. Support structure
International Nuclear Information System (INIS)
Conlee, J.L.
1982-01-01
The EBT-P support structure provides structural support for the 36 mirror coil magnets, magnet protection system, the toroidal vessel, and much of the device ancillary equipment. The structure is comprised of a primary support and a superstructure. The primary support is a reinforced concrete ring located directly inboard of the torus and is supported by nine columns. The toroidal vessel and the mirror coil magnets are cantilevered from the ring with the centerline of the torus located eight feet above the floor. The superstructure is an aluminum truss structure that rests on the concrete ring. The superstructure provides support for the device ancillary equipment. Engineering drawings of the support structure are given
On the runaway instability of self-gravitating torus around black holes
International Nuclear Information System (INIS)
Font, Jose A; Montero, Pedro J; Shibata, Masaru
2010-01-01
Black holes surrounded by self-gravitating tori are astrophysical systems which may naturally form following the core collapse of a massive star or the merger of two neutron stars. We present here results from fully general relativistic numerical simulations of such systems in order to assess the influence of the torus self-gravity on the onset of the so-called runaway instability. This instability, which might drive the rapid accretion of the disk on shorter timescales than those required to power a relativistic fireball, potentially challenges current models of gamma-ray bursts. Our simulations indicate that the self-gravity of the torus does not actually favour the onset of the instability.
Vertical injection of compact torus into the STOR-M tokamak
International Nuclear Information System (INIS)
Liu, D.; Singh, A.K.; Hirose, A.; Xiao, C.
2005-01-01
Vertical compact torus injection into the STOR-M tokamak has been conducted with the University of Saskatchewan Compact Torus Injector (USCTI). The injector stayed at the horizontal position and the CT was bent by 90 deg. using a curved conducting drift tube. The curved drift tube did not have significant effects on the CT velocity. Furthermore, the curved drift tube did not change the magnetic field topology. Preliminary vertical CT injection experiments have been carried out on the STOR-M tokamak. CT injection induced prompt increase in the electron density and in the soft x-ray radiation level. Further modifications of the 90 deg. are underway to improve the CT parameters and to further study the effects of CT injection on the tokamak plasma parameters. (author)
Hopf bifurcation and chaos from torus breakdown in voltage-mode controlled DC drive systems
International Nuclear Information System (INIS)
Dai Dong; Ma Xikui; Zhang Bo; Tse, Chi K.
2009-01-01
Period-doubling bifurcation and its route to chaos have been thoroughly investigated in voltage-mode and current-mode controlled DC motor drives under simple proportional control. In this paper, the phenomena of Hopf bifurcation and chaos from torus breakdown in a voltage-mode controlled DC drive system is reported. It has been shown that Hopf bifurcation may occur when the DC drive system adopts a more practical proportional-integral control. The phenomena of period-adding and phase-locking are also observed after the Hopf bifurcation. Furthermore, it is shown that the stable torus can breakdown and chaos emerges afterwards. The work presented in this paper provides more complete information about the dynamical behaviors of DC drive systems.
Mechanical design assessments of structural components and auxiliaries of the Joint European Torus
International Nuclear Information System (INIS)
Sonnerup, L.
1985-01-01
The general design of the Joint European Torus (JET) is briefly described. The loads on its major structural components, at normal operation, and in cases of plasma instability and/or disruption, are discussed. The way these components have been assessed and optimised in relation to their loads is presented. A short account of mechanical design problems of auxiliary equipment is given. Finally, the state of operation of JET and its implications for the mechanical design at the time of the conference will be summarized. The mechanically most important components of the JET device are the support structure of the toroidal magnet, th vacuum vessel, the coils of the magnets and the pedestals supporting the weight of the torus. These components all participate in resisting and transmitting the primary forces during operation. (orig.)
Mechanical design assessments of structural components and auxiliaries of the Joint European Torus
International Nuclear Information System (INIS)
Sonnerup, L.
1986-01-01
The general design of the Joint European Torus (JET) is briefly described. The loads on its major structural components, at normal operation, and in cases of plasma instability and/or disruption, are discussed. The way these components have been assessed and optimised in relation to their loads is presented. A short account of mechanical design problems of auxiliary equipment is given. Finally, the state of operation of JET and its implications for the mechanical design is summarized. The mechanically most important components of the JET device are the support structure of the toroidal magnet, the vacuum vessel, the coils of the magnets and the pedestals supporting the weight of the torus. These components all participate in resisting and transmitting the primary forces during operation. (orig.)
Numerical study of the Columbia high-beta device: Torus-II
International Nuclear Information System (INIS)
Izzo, R.
1981-01-01
The ionization, heating and subsequent long-time-scale behavior of the helium plasma in the Columbia fusion device, Torus-II, is studied. The purpose of this work is to perform numerical simulations while maintaining a high level of interaction with experimentalists. The device is operated as a toroidal z-pinch to prepare the gas for heating. This ionization of helium is studied using a zero-dimensional, two-fluid code. It is essentially an energy balance calculation that follows the development of the various charge states of the helium and any impurities (primarily silicon and oxygen) that are present. The code is an atomic physics model of Torus-II. In addition to ionization, we include three-body and radiative recombination processes
Numerical study of the Columbia high-beta device: Torus-II
Energy Technology Data Exchange (ETDEWEB)
Izzo, R.
1981-01-01
The ionization, heating and subsequent long-time-scale behavior of the helium plasma in the Columbia fusion device, Torus-II, is studied. The purpose of this work is to perform numerical simulations while maintaining a high level of interaction with experimentalists. The device is operated as a toroidal z-pinch to prepare the gas for heating. This ionization of helium is studied using a zero-dimensional, two-fluid code. It is essentially an energy balance calculation that follows the development of the various charge states of the helium and any impurities (primarily silicon and oxygen) that are present. The code is an atomic physics model of Torus-II. In addition to ionization, we include three-body and radiative recombination processes.
Energy Technology Data Exchange (ETDEWEB)
Arbanas, G; Elster, C; Escher, J; Mukhamedzanov, A; Nunes, F; Thompson, I J
2012-02-24
The TORUS collaboration derives its name from the research it focuses on, namely the Theory of Reactions for Unstable iSotopes. It is a Topical Collaboration in Nuclear Theory, and funded by the Nuclear Theory Division of the Office of Nuclear Physics in the Office of Science of the Department of Energy. The funding supports one postdoctoral researcher for the years 1 through 3. The collaboration brings together as Principal Investigators a large fraction of the nuclear reaction theorists currently active within the USA. The mission of the TORUS Topical Collaboration is to develop new methods that will advance nuclear reaction theory for unstable isotopes by using three-body techniques to improve direct-reaction calculations, and, by using a new partial-fusion theory, to integrate descriptions of direct and compound-nucleus reactions. This multi-institution collaborative effort is directly relevant to three areas of interest: the properties of nuclei far from stability; microscopic studies of nuclear input parameters for astrophysics, and microscopic nuclear reaction theory.
Pedretti, Kevin T.; Fineberg, Samuel A.; Kutler, Paul (Technical Monitor)
1997-01-01
A variety of different network technologies and topologies are currently being evaluated as part of the Whitney Project. This paper reports on the implementation and performance of a Fast Ethernet network configured in a 4x4 2D torus topology in a testbed cluster of 'commodity' Pentium Pro PCs. Several benchmarks were used for performance evaluation: an MPI point to point message passing benchmark, an MPI collective communication benchmark, and the NAS Parallel Benchmarks version 2.2 (NPB2). Our results show that for point to point communication on an unloaded network, the hub and 1 hop routes on the torus have about the same bandwidth and latency. However, the bandwidth decreases and the latency increases on the torus for each additional route hop. Collective communication benchmarks show that the torus provides roughly four times more aggregate bandwidth and eight times faster MPI barrier synchronizations than a hub based network for 16 processor systems. Finally, the SOAPBOX benchmarks, which simulate real-world CFD applications, generally demonstrated substantially better performance on the torus than on the hub. In the few cases the hub was faster, the difference was negligible. In total, our experimental results lead to the conclusion that for Fast Ethernet networks, the torus topology has better performance and scales better than a hub based network.
Energy Technology Data Exchange (ETDEWEB)
D.S. Darrow; S.S. Medley; A.L. Roquemore; W.W. Heidbrink; A. Alekseyev; F.E. Cecil; J. Egedal; V.Ya. Goloborod' ko; N.N. Gorelenkov; M. Isobe; S. Kaye; M. Miah; F. Paoletti; M.H. Redi; S.N. Reznik; A. Rosenberg; R. White; D. Wyatt; V.A. Yavorskij
2002-10-15
A range of effects may make fast ion confinement in spherical tokamaks worse than in conventional aspect ratio tokamaks. Data from neutron detectors, a neutral particle analyzer, and a fast ion loss diagnostic on the National Spherical Torus Experiment (NSTX) indicate that neutral beam ion confinement is consistent with classical expectations in quiescent plasmas, within the {approx}25% errors of measurement. However, fast ion confinement in NSTX is frequently affected by magnetohydrodynamic (MHD) activity, and the effect of MHD can be quite strong.
Confinement of Neutral Beam Ions in the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Darrow, D.S.; Medley, S.S.; Roquemore, A.L.; Rosenberg, A.
2001-01-01
The loss of neutral-beam ions to the wall has been measured in the National Spherical Torus Experiment (NSTX) by means of thermocouples, an infrared (IR) camera, and a Faraday cup probe. The losses tend to exhibit the expected dependences on plasma current, tangency radius of the injector, and plasma outer gap. However, the thermocouples and the Faraday cups indicate substantially different levels of loss and this difference has yet to be understood
DEFF Research Database (Denmark)
Gravesen, Jens; Willatzen, Morten; Voon, L.C. Lew Yan
2005-01-01
The theory of a quantum-mechanical particle confined to a surface of revolution is described using differential geometry methods including the derivation of a general set of three ordinary differential equations in curved coordinates. The problem is shown to be completely separable with the present...... hard-wall boundary conditions. Two case studies of recent experimental interest. the nanocone and torus-shaped nanoring structures. are analyzed in terms of eigenstates, energies. and symmetry characteristics based on the theory presented....
Remote handling of JET in-torus components. A practical experience
International Nuclear Information System (INIS)
Mills, S.; Brade, R.; Edwards, P.
2000-01-01
This paper summarises the experiences gained from the extensive handling of JET components inside the torus. The problems involved with handling components not designed to be remotely handled and the methods used to overcome them are described and discussed with specific examples from recent JET remote operations. The method employed for remotely producing structural TIG welds is explained. The problems of dextrous manipulation in an inverted attitude are discussed and the methods of amelioration are described
Descent of line bundles to GIT quotients of flag varieties by maximal torus
Kumar, Shrawan
2007-01-01
Let L be a homogeneous ample line bundle on any flag variety G/P and let T be a maximal torus of G. We prove a general necessary and sufficient condition for L to descend as a line bundle on the GIT quotient of G/P by T. We use this result to explicitly determine exactly which L descend to the GIT quotient for any simple complex algebraic group G and any parabolic subgroup P.
Proposal of a torus pumping and fuel recycling system for ITER
International Nuclear Information System (INIS)
Perinic, D.; Mack, A.; Perinic, G.; Murdoch, D.
1995-01-01
A universal torus pumping and fuel recycling system is proposed for all operation modes of ITER. It comprises primary cryopumps and secondary fuel separating cryopumps located inside the cryostat and a common mechanical forepump station located outside the cryostat. In this paper two different primary cryopump options are compared. The results of Monte Carlo calculations of pumping probabilities for helium show a significant difference leading to a distinct preference for the concept of a co-pumping cryopump. (orig.)
CPRF/ZTH front-end torus design and fabrication status
International Nuclear Information System (INIS)
Ballard, E.O.; Baker, C.; Gomez, T.; Prince, P.P.; Smith, R.L.
1989-01-01
Design of the ZTH front-end torus has been completed for a new generation Reversed Field Pinch (RFP) machine to be assembled at Los Alamos National Laboratory during FY 92. The Confinement Physics Research Facility (CPRF) houses the ZTH front-end torus. The ZTH torus consists of an Inconel 625 vacuum vessel supported by an external electrically conducting 304L stainless steel shell. Interspace support rings support the vacuum vessel to the shell and also provide accurate radial support for the interspace electrical diagnostics. The shell also supports 48 toroidal field coils that are mounted to the shell's external surface. The shell consists of an explosion bonded stainless steel-copper composite with water-cooling tube assemblies attached to the outer surface. The 0.135-in. thick copper is on the inside surface of the shell, and provides an electrically conducting path with the required electrical time constant of 50 ms. The shell plate will be formed to the required toroidal configuration, after which the poloidal and toroidal flanges will be welded to the structure and machined. The Inconel vacuum vessel consists of bellows segments, armor support rings, and diagnostic stations welded together to form the complete vacuum vessel assembly. The necessity for accurate positioning of the vacuum vessel within the shell requires that the shell and vacuum vessel be fabricated with major diameter tolerances within 0.050-in. true position of the nominal diameters of 188.0-in. and 188.820-in., respectively. 7 figs
Advanced tokamak reactors based on the spherical torus (ATR/ST). Preliminary design considerations
International Nuclear Information System (INIS)
Miller, R.L.; Krakowski, R.A.; Bathke, C.G.; Copenhaver, C.; Schnurr, N.M.; Engelhardt, A.G.; Seed, T.J.; Zubrin, R.M.
1986-06-01
Preliminary design results relating to an advanced magnetic fusion reactor concept based on the high-beta, low-aspect-ratio, spherical-torus tokamak are summarized. The concept includes resistive (demountable) toroidal-field coils, magnetic-divertor impurity control, oscillating-field current drive, and a flowing liquid-metal breeding blanket. Results of parametric tradeoff studies, plasma engineering modeling, fusion-power-core mechanical design, neutronics analyses, and blanket thermalhydraulics studies are described. The approach, models, and interim results described here provide a basis for a more detailed design. Key issues quantified for the spherical-torus reactor center on the need for an efficient drive for this high-current (approx.40 MA) device as well as the economic desirability to increase the net electrical power from the nominal 500-MWe(net) value adopted for the baseline system. Although a direct extension of present tokamak scaling, the stablity and transport of this high-beta (approx.0.3) plasma is a key unknown that is resoluble only by experiment. The spherical torus generally provides a route to improved tokamak reactors as measured by considerably simplified coil technology in a configuration that allows a realistic magnetic divertor design, both leading to increased mass power density and reduced cost
Two intervals Rényi entanglement entropy of compact free boson on torus
International Nuclear Information System (INIS)
Liu, Feihu; Liu, Xiao
2016-01-01
We compute the N=2 Rényi entanglement entropy of two intervals at equal time in a circle, for the theory of a 2D compact complex free scalar at finite temperature. This is carried out by performing functional integral on a genus 3 ramified cover of the torus, wherein the quantum part of the integral is captured by the four point function of twist fields on the worldsheet torus, and the classical piece is given by summing over winding modes of the genus 3 surface onto the target space torus. The final result is given in terms of a product of theta functions and certain multi-dimensional theta functions. We demonstrate the T-duality invariance of the result. We also study its low temperature limit. In the case in which the size of the intervals and of their separation are much smaller than the whole system, our result is in exact agreement with the known result for two intervals on an infinite system at zero temperature http://dx.doi.org/10.1088/1742-5468/2009/11/P11001. In the case in which the separation between the two intervals is much smaller than the interval length, the leading thermal corrections take the same universal form as proposed in http://dx.doi.org/10.1103/PhysRevLett.112.171603, http://dx.doi.org/10.1103/PhysRevD.91.105013 for Rényi entanglement entropy of a single interval.
A 12 coil superconducting bumpy torus magnet facility for plasma research
Roth, J. R.; Holmes, A. D.; Keller, T. A.; Krawczonek, W. M.
1972-01-01
A summary is presented of the performance of the two-coil superconducting pilot rig which preceded the NASA Lewis bumpy torus. This pilot rig was operated for 550 experimental runs over a period of 7 years. The NASA Lewis bumpy torus facility consists of 12 superconducting coils, each with a 19 cm in diameter and capable of producing magnetic field strengths of 3.0 teslas on their axes. The magnets are equally spaced around a major circumference 1.52 m in diameter, and are mounted with the major axis of the torus vertical in a single vacuum tank 2.59 m in diameter. The design value of maximum magnetic field on the magnetic axis (3.0 teslas) was reached and exceeded. A maximum magnetic field of 3.23 teslas was held for a period of 60 minutes, and the coils did not go to normal. When the coils were charged to a maximum magnetic field of 3.35 teslas, the coil system was driven normal without damage to the facility.
Injerto óseo en bloque usando como donante torus mandibular. Reporte de caso
Directory of Open Access Journals (Sweden)
Oswaldo Cantillo Pallares
2014-01-01
Full Text Available Actualmente los materiales empleados para regeneración a través de injertos óseos están basados en compuestos sintéticos con propiedades en ocasiones poco predecibles para los pacientes. Los torus son exostosis óseas de etiología desconocida y pueden ser utilizados como injertos óseos con resultados clínicos exitosos. Así, el objetivo de este reporte de caso es describir la técnica quirúrgica de injerto óseo en bloque utilizando como donante torus mandibulares. Los resultados clínicos a 8 semanas postoperatorias evidenciaron tejidos en cicatrización y pocas molestias referidas por el paciente. Los injertos óseos provenientes de torus mandibulares son técnicas quirúrgicas de mediana complejidad que pueden ser empleados y permiten la obtención de resultados clínicos similares a los de otros materiales.
Energy Technology Data Exchange (ETDEWEB)
Sechrest, Y.; Munsat, T. [Department of Physics, University of Colorado, Boulder, Colorado 80309 (United States); Smith, D. [Department of Engineering Physics, University of Wisconsin-Madison, Madison, Wisconsin 53706 (United States); Stotler, D. P.; Zweben, S. J. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08540 (United States)
2015-05-15
In this study, the close physical proximity of the Gas Puff Imaging (GPI) and Beam Emission Spectroscopy (BES) diagnostics on the National Spherical torus Experiment (NSTX) is leveraged to directly compare fluctuation measurements, and to study the local effects of the GPI neutral deuterium puff during H-mode plasmas without large Edge Localized Modes. The GPI and BES views on NSTX provide partially overlapping coverage of the edge and scrape-off layer (SOL) regions above the outboard midplane. The separation in the toroidal direction is 16°, and field lines passing through diagnostic views are separated by ∼20 cm in the direction perpendicular to the magnetic field. Strong cross-correlation is observed, and strong cross-coherence is seen for frequencies between 5 and 15 kHz. Also, probability distribution functions of fluctuations measured ∼3 cm inside the separatrix exhibit only minor deviations from a normal distribution for both diagnostics, and good agreement between correlation length estimates, decorrelation times, and structure velocities is found at the ±40% level. While the two instruments agree closely in many respects, some discrepancies are observed. Most notably, GPI normalized fluctuation levels exceed BES fluctuations by a factor of ∼9. BES mean intensity is found to be sensitive to the GPI neutral gas puff, and BES normalized fluctuation levels for frequencies between 1 and 10 kHz are observed to increase during the GPI puff.
International Nuclear Information System (INIS)
Liu, D; Heidbrink, W W; Podesta, M; Ruskov, E; Bell, R E; Fredrickson, E D; Medley, S S; Harvey, R W
2010-01-01
Combined neutral beam injection and high-harmonic fast-wave (HHFW) heating accelerate deuterium fast ions in the National Spherical Torus Experiment (NSTX). With 1.1 MW of HHFW power, the neutron emission rate is about three times larger than in the comparison discharge without HHFW heating. Acceleration of fast ions above the beam injection energy is evident on an E||B type neutral particle analyzer (NPA), a 4-chord solid state neutral particle analyzer (SSNPA) array and a 16-channel fast-ion D-alpha (FIDA) diagnostic. The accelerated fast ions observed by the NPA and SSNPA diagnostics mainly come from passive charge exchange reactions at the edge due to the NPA/SSNPA localization in phase space. The spatial profile of accelerated fast ions that is measured by the FIDA diagnostic is much broader than in conventional tokamaks because of the multiple resonance layers and large orbits in NSTX. The fast-ion distribution function calculated by the CQL3D Fokker-Planck code differs from the measured spatial profile, presumably because the current version of CQL3D uses a zero-banana-width model. In addition, compressional Alfven eigenmode activity is stronger during the HHFW heating and it may affect the fast-ion spatial profile.
International Nuclear Information System (INIS)
Kuritsyn, A.; Fiksel, G.; Almagri, A. F.; Miller, M. C.; Mirnov, V. V.; Prager, S. C.; Sarff, J. S.; Brower, D. L.; Ding, W. X.
2009-01-01
In this paper measurements of momentum and current transport caused by current driven tearing instability are reported. The measurements are done in the Madison Symmetric Torus reversed-field pinch [R. N. Dexter, D. W. Kerst, T. W. Lovell, S. C. Prager, and J. C. Sprott, Fusion Technol. 19, 131 (1991)] in a regime with repetitive bursts of tearing instability causing magnetic field reconnection. It is established that the plasma parallel momentum profile flattens during these reconnection events: The flow decreases in the core and increases at the edge. The momentum relaxation phenomenon is similar in nature to the well established relaxation of the parallel electrical current and could be a general feature of self-organized systems. The measured fluctuation-induced Maxwell and Reynolds stresses, which govern the dynamics of plasma flow, are large and almost balance each other such that their difference is approximately equal to the rate of change of plasma momentum. The Hall dynamo, which is directly related to the Maxwell stress, drives the parallel current profile relaxation at resonant surfaces at the reconnection events. These results qualitatively agree with analytical calculations and numerical simulations. It is plausible that current-driven instabilities can be responsible for momentum transport in other laboratory and astrophysical plasmas.
International Nuclear Information System (INIS)
Sechrest, Y.; Munsat, T.; Smith, D.; Stotler, D. P.; Zweben, S. J.
2015-01-01
In this study, the close physical proximity of the Gas Puff Imaging (GPI) and Beam Emission Spectroscopy (BES) diagnostics on the National Spherical torus Experiment (NSTX) is leveraged to directly compare fluctuation measurements, and to study the local effects of the GPI neutral deuterium puff during H-mode plasmas without large Edge Localized Modes. The GPI and BES views on NSTX provide partially overlapping coverage of the edge and scrape-off layer (SOL) regions above the outboard midplane. The separation in the toroidal direction is 16°, and field lines passing through diagnostic views are separated by ∼20 cm in the direction perpendicular to the magnetic field. Strong cross-correlation is observed, and strong cross-coherence is seen for frequencies between 5 and 15 kHz. Also, probability distribution functions of fluctuations measured ∼3 cm inside the separatrix exhibit only minor deviations from a normal distribution for both diagnostics, and good agreement between correlation length estimates, decorrelation times, and structure velocities is found at the ±40% level. While the two instruments agree closely in many respects, some discrepancies are observed. Most notably, GPI normalized fluctuation levels exceed BES fluctuations by a factor of ∼9. BES mean intensity is found to be sensitive to the GPI neutral gas puff, and BES normalized fluctuation levels for frequencies between 1 and 10 kHz are observed to increase during the GPI puff
International Nuclear Information System (INIS)
Morita, S.; Oishi, T.; Kobayashi, M.; Goto, M.; Kawamura, G.; Zhang, H.M.; Hunag, X.L.; Wang, E.H.
2014-01-01
Two-dimensional (2-D) distribution of impurity line emissions has been measured in Large Helical Device (LHD) based on the 2-D extreme ultraviolet (EUV) spectroscopy for studying the edge impurity transport in stochastic magnetic field layer with three-dimensional (3-D) structure. The impurity behavior in the vicinity of two X-points at inboard and outboard sides of torus becomes separately visible with the 2-D measurement. As a result, it is found that the carbon location changes from inboard to outboard X-points when the plasma axis is shifted from R_a_x=3.6 m to 3.75 m. A 3-D simulation with EMC3-EIRENE code agrees with the result at R_a_x=3.75 m but disagreed with the result at R_a_x=3.60 m. The discrepancy between the measurement and simulation at R_a_x=3.60 m is considerably reduced when the effect of neutral hydrogen localized at the inboard side is taken into account, which can modify the density gradient and friction force along the magnetic field. (author)
International Nuclear Information System (INIS)
Martin, R.W.; McCauley, E.W.
1977-09-01
The authors investigated the effects of torus wall flexibility in the pressure suppression system of a Mark I boiling water reactor (BWR) when the torus wall is subjected to hydrodynamic loadings. Using hypothetical models, they examined these flexibility effects under two hydrodynamic loading conditions: (1) a steam relief valve (SRV) discharge pulse, and (2) a loss-of-coolant accident (LOCA) chugging pulse. In the analyses of these events they used a recently developed two-dimensional finite element computer code. Taking the basic geometry and dimensions of the Monticello Mark I BWR nuclear power plant (in Monticello, Minnesota, U.S.A.), they assessed the effects of flexibility in the torus wall by changing values of the inside-diameter-to-wall-thickness ratio. Varying the torus wall thickness (t) with respect to the inside diameter (D) of the torus, they assigned values to the ratio D/t ranging from 0 (infinitely rigid) to 600 (highly flexible). In the case of a modeled steam relief valve (SRV) discharge pulse, they found the peak vertical reaction force on the torus was reduced from that of a rigid wall response by a factor of 3 for the most highly flexible, plant-simulated wall (D/t = 600). The reduction factor for a modeled loss-of-coolant accident (LOCA) chugging pulse was shown to be 1.5. The two-dimensional analyses employed overestimate these reduction factors but have provided, as intended, definition of the effect of torus boundary stiffness. In the work planned for FY79, improved modeling of the structure and of the source is expected to result in factors more directly applicable to actual pressure suppression systems
International Nuclear Information System (INIS)
Alonso-Herrero, Almudena; Ramos Almeida, Cristina; Mason, Rachel; Asensio Ramos, Andres; Rodriguez Espinosa, Jose Miguel; Perez-Garcia, Ana M.; Roche, Patrick F.; Levenson, Nancy A.; Elitzur, Moshe; Packham, Christopher; Young, Stuart; Diaz-Santos, Tanio
2011-01-01
We used the CLUMPY torus models and a Bayesian approach to fit the infrared spectral energy distributions and ground-based high angular resolution mid-infrared spectroscopy of 13 nearby Seyfert galaxies. This allowed us to put tight constraints on torus model parameters such as the viewing angle i, the radial thickness of the torus Y, the angular size of the cloud distribution σ torus , and the average number of clouds along radial equatorial rays N 0 . We found that the viewing angle i is not the only parameter controlling the classification of a galaxy into type 1 or type 2. In principle, type 2s could be viewed at any viewing angle i as long as there is one cloud along the line of sight. A more relevant quantity for clumpy media is the probability for an active galactic nucleus (AGN) photon to escape unabsorbed. In our sample, type 1s have relatively high escape probabilities, P esc ∼ 12%-44%, while type 2s, as expected, tend to have very low escape probabilities. Our fits also confirmed that the tori of Seyfert galaxies are compact with torus model radii in the range 1-6 pc. The scaling of the models to the data also provided the AGN bolometric luminosities L bol (AGN), which were found to be in good agreement with estimates from the literature. When we combined our sample of Seyfert galaxies with a sample of PG quasars from the literature to span a range of L bol (AGN) ∼ 10 43 -10 47 erg s -1 , we found plausible evidence of the receding torus. That is, there is a tendency for the torus geometrical covering factor to be lower (f 2 ∼ 0.1-0.3) at high AGN luminosities than at low AGN luminosities (f 2 ∼ 0.9-1 at ∼10 43 -10 44 erg s -1 ). This is because at low AGN luminosities the tori appear to have wider angular sizes (larger σ torus ) and more clouds along radial equatorial rays. We cannot, however, rule out the possibility that this is due to contamination by extended dust structures not associated with the dusty torus at low AGN luminosities
The mechanical structure of the Joint European Torus
International Nuclear Information System (INIS)
Huguet, M.; Sonnerup, L.; Celentano, G.; Booth, J.; Raimondi, T.
1976-01-01
The JET mechanical structure is designed to resist with suitable stiffness the large azimuthal forces acting on the 32 toroidal field coils. Due to the limited space available the structure is designed as a thin closed shell giving a maximum torsional rigidity with a minimum of material thickness. Externally the structure consists of a thin shell surrounding the toroidal magnet. The shell is attached at top and bottom to two disc-shaped rings which are provided with side supports for the coils. Finally along the inner straight portion, the coils are supported by a grooved cylinder which is attached to the upper and lower rings. To facilitate assembly and maintenance the structure is divided into 8 identical sectors. Insulation gaps have been provided between sectors to reduce eddy current and allow for the penetration of the poloidal field through the structure. One of the major problems is the design of the connections between sectors. A combination of insulated bolts and keys has been provided to resist the very high shear loads. A three dimensional finite element code has been used to compute stresses and deformations. Photoelastic tests have been carried out in order to assess the design of critical areas. In particular, openings in the structure give rise to stress concentrations which can be made tolerable with a proper design of the hole rims
International Nuclear Information System (INIS)
Mattingly, S.E.K.; Moir, R.W.
1992-01-01
Concern has been expressed about the conceptual design of fusion reactors using a Compact Torus Accelerator (CTA). A CTA accelerates a plasma torus toward a fusion target. When the torus nears the target, it is compressed and focused down to a small volume, creating a very high energy density and initiating a fusion micro explosion. The focusing cone is destroyed with each shot due to the stress from the passage of the torus as well as from the force of the explosion (1 800 MJ of yield, ∼0.5 Ton TNT equivalent). The focusing cone could be made of solidified Li 2 BeF 4 ; the same material used in liquid state to protect the reaction chamber from the micro explosion and to transport heat away to a power plant. The problem with this design is that when the focusing cone is shattered, the resulting small pieces of solid and liquid debris (ejecta) might be carded along by the expanding vapor of the explosion and might enter the CTA itself, causing damage and shortening the life of the CTA. The proposed solution for this possible problem is to bend the focusing cone so that the ejecta no longer have a clear path to the CTA. Calculations show that the plasma torus may be sent through a radius of curvature of less than 0.5 m just after the focusing cone, without significantly disturbing the plasma
Dynamics of magnetic fields in Maxwell, Yang-Mills and Chern-Simons theories on the torus
International Nuclear Information System (INIS)
Burgess, M.; McLachlan, A.; Toms, D.J.
1992-01-01
The problem of uniform magnetic fields passing perpendicularly through a 2-torus, Abelian and Non-Abelian, is considered. Focus is on dynamical effects of non-integrable phases on the torus at non zero B and from magnetic fields themselves in the vacuum. The spectrum is computed and is shown to be always independent of the non-integrable phases on the torus. It is concluded that a Chern-Simons term will always be induced by radiative corrections to fermions on the torus when B ≠ 0. The special case of an electromagnetically uncharged anyon gas in noted and shown to be a system whose spectrum can depend on the non-integrable phases in the two torus directions, subject to a consistency requirement. In three and four dimensions, dynamical symmetry breaking of non-Abelian fields and associated condensate formation is possible by radiative corrections. The classification on non-Abelian magnetic fields in terms of ''flux integers'' is discussed, and a method for obtaining such integers for an arbitrary gauge algebra is presented. This provides a rigorous generalisation of Hooft's su (2) classification. 72 refs., 5 figs
International Nuclear Information System (INIS)
Arthur, D.
1977-01-01
The Lawrence Livermore Laboratory is currently involved in a 1/5 scale testing program on the Mark I BWR pressure suppression system. A key element of the test setup is a pressure vessel that is a 90 0 sector of a torus. Proper performance of the 90 0 torus depends on its structural integrity and structural dynamic characteristics. It must sustain the internal pressurization of the planned tests, and its dynamic response to the transient test loads should be minimal. If the structural vibrations are too great, interpretation of important load cell and pressure transducer data will be difficult. The purpose of the report is to bring together under one cover calculations pertaining to the structural dynamic characteristics and structural integrity of 90 0 torus. The report is divided into the following sections: (1) system description in which the torus and associated hardware are briefly described; (2) structural dynamics in which calculations of natural frequency and dynamic response are presented; and (3) structural integrity in which stress calculations for design purposes are presented; and an appendix which contains an LLL internal report comparing the expected load cell response for a three and four-point supported torus
Overview of physics results from the conclusive operation of the National Spherical Torus Experiment
Sabbagh, S. A.; Ahn, J.-W.; Allain, J.; Andre, R.; Balbaky, A.; Bastasz, R.; Battaglia, D.; Bell, M.; Bell, R.; Beiersdorfer, P.; Belova, E.; Berkery, J.; Betti, R.; Bialek, J.; Bigelow, T.; Bitter, M.; Boedo, J.; Bonoli, P.; Boozer, A.; Bortolon, A.; Boyle, D.; Brennan, D.; Breslau, J.; Buttery, R.; Canik, J.; Caravelli, G.; Chang, C.; Crocker, N.; Darrow, D.; Davis, B.; Delgado-Aparicio, L.; Diallo, A.; Ding, S.; D'Ippolito, D.; Domier, C.; Dorland, W.; Ethier, S.; Evans, T.; Ferron, J.; Finkenthal, M.; Foley, J.; Fonck, R.; Frazin, R.; Fredrickson, E.; Fu, G.; Gates, D.; Gerhardt, S.; Glasser, A.; Gorelenkov, N.; Gray, T.; Guo, Y.; Guttenfelder, W.; Hahm, T.; Harvey, R.; Hassanein, A.; Heidbrink, W.; Hill, K.; Hirooka, Y.; Hooper, E. B.; Hosea, J.; Humphreys, D.; Indireshkumar, K.; Jaeger, F.; Jarboe, T.; Jardin, S.; Jaworski, M.; Kaita, R.; Kallman, J.; Katsuro-Hopkins, O.; Kaye, S.; Kessel, C.; Kim, J.; Kolemen, E.; Kramer, G.; Krasheninnikov, S.; Kubota, S.; Kugel, H.; La Haye, R. J.; Lao, L.; LeBlanc, B.; Lee, W.; Lee, K.; Leuer, J.; Levinton, F.; Liang, Y.; Liu, D.; Lore, J.; Luhmann, N., Jr.; Maingi, R.; Majeski, R.; Manickam, J.; Mansfield, D.; Maqueda, R.; Mazzucato, E.; McLean, A.; McCune, D.; McGeehan, B.; McKee, G.; Medley, S.; Meier, E.; Menard, J.; Menon, M.; Meyer, H.; Mikkelsen, D.; Miloshevsky, G.; Mueller, D.; Munsat, T.; Myra, J.; Nelson, B.; Nishino, N.; Nygren, R.; Ono, M.; Osborne, T.; Park, H.; Park, J.; Park, Y. S.; Paul, S.; Peebles, W.; Penaflor, B.; Perkins, R. J.; Phillips, C.; Pigarov, A.; Podesta, M.; Preinhaelter, J.; Raman, R.; Ren, Y.; Rewoldt, G.; Rognlien, T.; Ross, P.; Rowley, C.; Ruskov, E.; Russell, D.; Ruzic, D.; Ryan, P.; Schaffer, M.; Schuster, E.; Scotti, F.; Shaing, K.; Shevchenko, V.; Shinohara, K.; Sizyuk, V.; Skinner, C. H.; Smirnov, A.; Smith, D.; Snyder, P.; Solomon, W.; Sontag, A.; Soukhanovskii, V.; Stoltzfus-Dueck, T.; Stotler, D.; Stratton, B.; Stutman, D.; Takahashi, H.; Takase, Y.; Tamura, N.; Tang, X.; Taylor, G.; Taylor, C.; Tritz, K.; Tsarouhas, D.; Umansky, M.; Urban, J.; Untergberg, E.; Walker, M.; Wampler, W.; Wang, W.; Whaley, J.; White, R.; Wilgen, J.; Wilson, R.; Wong, K. L.; Wright, J.; Xia, Z.; Youchison, D.; Yu, G.; Yuh, H.; Zakharov, L.; Zemlyanov, D.; Zimmer, G.; Zweben, S. J.
2013-10-01
Research on the National Spherical Torus Experiment, NSTX, targets physics understanding needed for extrapolation to a steady-state ST Fusion Nuclear Science Facility, pilot plant, or DEMO. The unique ST operational space is leveraged to test physics theories for next-step tokamak operation, including ITER. Present research also examines implications for the coming device upgrade, NSTX-U. An energy confinement time, τE, scaling unified for varied wall conditions exhibits a strong improvement of BTτE with decreased electron collisionality, accentuated by lithium (Li) wall conditioning. This result is consistent with nonlinear microtearing simulations that match the experimental electron diffusivity quantitatively and predict reduced electron heat transport at lower collisionality. Beam-emission spectroscopy measurements in the steep gradient region of the pedestal indicate the poloidal correlation length of turbulence of about ten ion gyroradii increases at higher electron density gradient and lower Ti gradient, consistent with turbulence caused by trapped electron instabilities. Density fluctuations in the pedestal top region indicate ion-scale microturbulence compatible with ion temperature gradient and/or kinetic ballooning mode instabilities. Plasma characteristics change nearly continuously with increasing Li evaporation and edge localized modes (ELMs) stabilize due to edge density gradient alteration. Global mode stability studies show stabilizing resonant kinetic effects are enhanced at lower collisionality, but in stark contrast have almost no dependence on collisionality when the plasma is off-resonance. Combined resistive wall mode radial and poloidal field sensor feedback was used to control n = 1 perturbations and improve stability. The disruption probability due to unstable resistive wall modes (RWMs) was surprisingly reduced at very high βN/li > 10 consistent with low frequency magnetohydrodynamic spectroscopy measurements of mode stability. Greater
Transient induced tungsten melting at the Joint European Torus (JET)
Coenen, J. W.; Matthews, G. F.; Krieger, K.; Iglesias, D.; Bunting, P.; Corre, Y.; Silburn, S.; Balboa, I.; Bazylev, B.; Conway, N.; Coffey, I.; Dejarnac, R.; Gauthier, E.; Gaspar, J.; Jachmich, S.; Jepu, I.; Makepeace, C.; Scannell, R.; Stamp, M.; Petersson, P.; Pitts, R. A.; Wiesen, S.; Widdowson, A.; Heinola, K.; Baron-Wiechec, A.; Contributors, JET
2017-12-01
Melting is one of the major risks associated with tungsten (W) plasma-facing components (PFCs) in tokamaks like JET or ITER. These components are designed such that leading edges and hence excessive plasma heat loads deposited at near normal incidence are avoided. Due to the high stored energies in ITER discharges, shallow surface melting can occur under insufficiently mitigated plasma disruption and so-called edge localised modes—power load transients. A dedicated program was carried out at the JET to study the physics and consequences of W transient melting. Following initial exposures in 2013 (ILW-1) of a W-lamella with leading edge, new experiments have been performed on a sloped surface (15{}\\circ slope) during the 2015/2016 (ILW-3) campaign. This new experiment allows significantly improved infrared thermography measurements and thus resolved important issue of power loading in the context of the previous leading edge exposures. The new lamella was monitored by local diagnostics: spectroscopy, thermography and high-resolution photography in between discharges. No impact on the main plasma was observed despite a strong increase of the local W source consistent with evaporation. In contrast to the earlier exposure, no droplet emission was observed from the sloped surface. Topological modifications resulting from the melting are clearly visible between discharges on the photographic images. Melt damage can be clearly linked to the infrared measurements: the emissivity drops in zones where melting occurs. In comparison with the previous leading edge experiment, no runaway melt motion is observed, consistent with the hypothesis that the escape of thermionic electrons emitted from the melt zone is largely suppressed in this geometry, where the magnetic field intersects the surface at lower angles than in the case of perpendicular impact on a leading edge. Utilising both exposures allows us to further test the model of the forces driving melt motion that
Initial Results from the Lost Alpha Diagnostics on Joint European Torus
Energy Technology Data Exchange (ETDEWEB)
Darrow, Doug; Cecil, Ed; Ellis, Bob; Fullard, Keith; Hill, Ken; Horton, Alan; Kiptily, Vasily; Pedrick, Les; Reich, Matthias
2007-07-25
Two devices have been installed in the Joint European Torus (JET) vacuum vessel near the plasma boundary to investigate the loss of energetic ions and fusion products in general and alpha particles in particular during the upcoming JET experiments. These devices are (i) a set of multichannel thin foil Faraday collectors, and (ii) a well collimated scintillator which is optically connected to a charge-coupled device. Initial results, including the radial energy and poloidal dependence of lost ions from hydrogen and deuterium plasmas during the 2005–06 JET restart campaign, will be presented.
Topological Invariants and Ground-State Wave functions of Topological Insulators on a Torus
Directory of Open Access Journals (Sweden)
Zhong Wang
2014-01-01
Full Text Available We define topological invariants in terms of the ground-state wave functions on a torus. This approach leads to precisely defined formulas for the Hall conductance in four dimensions and the topological magnetoelectric θ term in three dimensions, and their generalizations in higher dimensions. They are valid in the presence of arbitrary many-body interactions and disorder. These topological invariants systematically generalize the two-dimensional Niu-Thouless-Wu formula and will be useful in numerical calculations of disordered topological insulators and strongly correlated topological insulators, especially fractional topological insulators.
Direct torus venting analysis for Chinshan BWR-4 plant with MARK-I containment
Energy Technology Data Exchange (ETDEWEB)
Yuann, Yng-Ruey, E-mail: ryyuann@iner.gov.tw
2017-03-15
Highlights: • Study the effectiveness of Direct Torus Venting System (DTVS) during extended SBO of 24 h for Chinshan MARK-I plant. • Containment response is analyzed by GOTHIC based on boundary conditions from RETRAN calculation. • Analyses are performed with and without DTVS, respectively. • Suppression pool is sub-divided and thermal stratification is observed. - Abstract: The Chinshan plant, owned by Taiwan Power Company, has twin units of BWR-4 reactor and MARK-I containment. Both units have been operating at rated core thermal power of 1840 MWt. The existing Direct Torus Venting System (DTVS) is the main system used for venting the containment during the extended station blackout event. The purpose of this paper is to study the effects of the DTVS venting on the response of the containment pressure and temperature. The reactor is depressurized by manually opening the safety relief valves (SRVs) during the SBO, which causes the mass and energy to be discharged into and heat up the suppression pool. The RETRAN model is used to calculate the Nuclear Steam Supply System (NSSS) response and generate the SRV blowdown conditions, including SRV pressure, enthalpy, and mass flow rate. These conditions are then used as the time-dependent boundary conditions for the GOTHIC code to calculate the containment pressure and temperature response. The DTVS model is established in the GOTHIC model based on the venting size, venting piping loss, venting initiation time, and venting source. The lumped volume model, 1-D coarse-mesh model, and 3-D coarse-mesh model are considered in the torus volume. The calculation is first done without DTVS venting to establish a reference basis. Then a case with DTVS available is performed. Comparison of the two cases shows that the existing DTVS design is effective in mitigating the severity of the containment pressure and temperature transients. The results also show that the 1-D coarse-mesh model may not be appropriate since a
On the geometry of certain irreducible non-torus plane sextics
DEFF Research Database (Denmark)
Eyral, Christophe; Oka, Mutsuo
2009-01-01
An irreducible non-torus plane sextic with simple singularities is said to be special if its fundamental group factors to a dihedral group. There exist (exactly) ten configurations of simple singularities that are realizable by such curves. Among them, six are realizable by non-special sextics...... as well. We conjecture that for each of these six configurations there always exists a non-special curve whose fundamental group is abelian, and we prove this conjecture for three configurations (another one has already been treated in one of our previous papers). As a corollary, we obtain new explicit...
Effects of a vertical magnetic field on particle confinement in a magnetized plasma torus.
Müller, S H; Fasoli, A; Labit, B; McGrath, M; Podestà, M; Poli, F M
2004-10-15
The particle confinement in a magnetized plasma torus with superimposed vertical magnetic field is modeled and measured experimentally. The formation of an equilibrium characterized by a parallel plasma current canceling out the grad B and curvature drifts is described using a two-fluid model. Characteristic response frequencies and relaxation rates are calculated. The predictions for the particle confinement time as a function of the vertical magnetic field are verified in a systematic experimental study on the TORPEX device, including the existence of an optimal vertical field and the anticorrelation between confinement time and density.
Partition function of a chiral boson on a 2-torus from the Floreanini–Jackiw Lagrangian
International Nuclear Information System (INIS)
Chen, Wei-Ming; Ho, Pei-Ming; Kao, Hsien-chung; Khoo, Fech Scen; Matsuo, Yutaka
2014-01-01
We revisit the problem of quantizing a chiral boson on a torus. The conventional approach is to extract the partition function of a chiral boson from the path integral of a non-chiral boson. Instead we compute it directly from the chiral boson Lagrangian of Floreanini and Jackiw modified by topological terms involving an auxiliary field. A careful analysis of the gauge-fixing condition for the extra gauge symmetry reproduces the correct results for the free chiral boson, and has the advantage of being applicable to a wider class of interacting chiral boson theories
Initial Results from the Lost Alpha Diagnostics on Joint European Torus
International Nuclear Information System (INIS)
Darrow, Doug; Baeumel, Stefan; Cecil, Ed; Ellis, Bob; Fullard, Keith; Hill, Ken; Horton, Alan; Kiptily, Vasily; Pedrick, Les; Reich, Matthias; Werner, Andreas
2007-01-01
Two devices have been installed in the Joint European Torus (JET) vacuum vessel near the plasma boundary to investigate the loss of energetic ions and fusion products in general and alpha particles in particular during the upcoming JET experiments. These devices are (i) a set of multichannel thin foil Faraday collectors, and (ii) a well collimated scintillator which is optically connected to a charge-coupled device. Initial results, including the radial energy and poloidal dependence of lost ions from hydrogen and deuterium plasmas during the 2005-06 JET restart campaign, will be presented.
Suppression of tilting instability of a compact torus by energetic particle beams
International Nuclear Information System (INIS)
Nomura, Yasuyuki.
1984-11-01
It is shown that the tilting instability of a compact torus can be suppressed by toroidally circulating energetic particle beams. The stabilizing mechanism is based on the properties of the forced oscillation in the motion of beam particles in a plasma ring. The required beam current for the stabilization is estimated to be sufficiently small compared to the plasma current in the case that the angular velocity of beam particles is close to the betatron frequency. This stabilizing method is applied to a field reversed configuration. Effects of the plasma surface current and beam divergences are also examined. (author)
Spin-k/2-spin-k/2 SU(2) two-point functions on the torus
International Nuclear Information System (INIS)
Kirsch, Ingo; Kucharski, Piotr
2012-11-01
We discuss a class of two-point functions on the torus of primary operators in the SU(2) Wess-Zumino-Witten model at integer level k. In particular, we construct an explicit expression for the current blocks of the spin-(k)/(2)-spin-(k)/(2) torus two-point functions for all k. We first examine the factorization limits of the proposed current blocks and test their monodromy properties. We then prove that the current blocks solve the corresponding Knizhnik-Zamolodchikov-like differential equations using the method of Mathur, Mukhi and Sen.
Spin-k/2-spin-k/2 SU(2) two-point functions on the torus
Energy Technology Data Exchange (ETDEWEB)
Kirsch, Ingo [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany). Gruppe Theorie; Kucharski, Piotr [Warsaw Univ. (Poland). Inst. of Theoretical Physics
2012-11-15
We discuss a class of two-point functions on the torus of primary operators in the SU(2) Wess-Zumino-Witten model at integer level k. In particular, we construct an explicit expression for the current blocks of the spin-(k)/(2)-spin-(k)/(2) torus two-point functions for all k. We first examine the factorization limits of the proposed current blocks and test their monodromy properties. We then prove that the current blocks solve the corresponding Knizhnik-Zamolodchikov-like differential equations using the method of Mathur, Mukhi and Sen.
International Nuclear Information System (INIS)
Nakamura, Yukiharu; Ozeki, Takahisa
1986-07-01
The finite element circuit theory is extended to the general eddy current problem in a multi-torus system, which consists of various torus conductors and axisymmetric coil systems. The numerical procedures are devised to avoid practical restrictions of computer storage and computing time, that is, the reduction technique of eddy current eigen modes to save storage and the introduction of shape function into the double area integral of mode coupling to save time. The numerical code EDDYMULT based on the theory is developed to use in designing tokamak device from the viewpoints of the evaluation of electromagnetic loading on the device components and the control analysis of tokamak equilibrium. (author)
Ultrasoft x-ray imaging system for the National Spherical Torus Experiment
Stutman, D.; Finkenthal, M.; Soukhanovskii, V.; May, M. J.; Moos, H. W.; Kaita, R.
1999-01-01
A spectrally resolved ultrasoft x-ray imaging system, consisting of arrays of high resolution (the National Spherical Torus Experiment. Initially, three poloidal arrays of diodes filtered for C 1s-np emission will be implemented for fast tomographic imaging of the colder start-up plasmas. Later on, mirrors tuned to the C Lyα emission will be added in order to enable the arrays to "see" the periphery through the hot core and to study magnetohydrodynamic activity and impurity transport in this region. We also discuss possible core diagnostics, based on tomographic imaging of the Lyα emission from the plume of recombined, low Z impurity ions left by neutral beams or fueling pellets. The arrays can also be used for radiated power measurements and to map the distribution of high Z impurities injected for transport studies. The performance of the proposed system is illustrated with results from test channels on the CDX-U spherical torus at Princeton Plasma Physics Laboratory.
Multilayer mirror and foil filter AXUV diode arrays on CDX-U spherical torus
International Nuclear Information System (INIS)
Soukhanovskii, V. A.; Stutman, D.; Iovea, M.; Finkenthal, M.; Moos, H. W.; Munsat, T.; Jones, B.; Hoffman, D.; Kaita, R.; Majeski, R.
2001-01-01
Recent upgrades to CDX-U spherical torus diagnostics include two 10-channel AXUV diode arrays. The multilayer mirror (MLM) array measures the λ150 O VI brightness profile in the poloidal plane using the Mo/B 4 C synthetic multilayer structures as dispersive elements. The foil filter array has a tangential view and is equipped with interchangeable clear aperture, beryllium and titanium filters. This allows measurements of radiated power, O VI or C V radial distributions, respectively. The O VI and C V emissivity and the radiated power profiles are highly peaked. A Neoclassical impurity accumulation mechanism is considered as an explanation. For radiated power measurements in the T e ≤100 eV plasmas, photon energy dependent corrections must be used in order to account for nonlinear AXUV sensitivity in the range E phot ≤20 eV. The arrays are also used for characterization of resistive MHD phenomena, such as the low m modes, saw-tooth oscillations and internal reconnection events. Based on the successful operation of the diagnostics, a new ultra soft x-ray multilayer mirror diode AXUV diode array monitoring the 34 Aa emissivity distribution of C VI will be built and installed on the National Spherical Torus Experiment
CPRF/ZTH front-end torus design and fabrication status
International Nuclear Information System (INIS)
Ballard, E.O.; Baker, C.; Gomez, T.; Prince, P.P.; Smith, R.L.
1989-01-01
Design of the ZTH front-end torus has been completed for a new generation Reversed Field Pinch (RFP) machine to be assembled at Los Alamos National Laboratory during FY 92. The Confinement Physics Research Facility (CPRF) houses the ZTH front-end. The ZTH torus consists of an Inconel 625 vacuum vessel supported by an external electrically conducting 304L stainless steel shell. Interspace support rings support the vacuum vessel to the shell and also provide accurate radial support for the interspace electrical diagnostics. The shell also supports 48 toroidal field coils that are mounted to the shell's external surface. The shell consists of an explosion bonded stainless steel-copper composite with water-cooling tube assemblies attached to the outer surface. The 0.135-in. thick copper is on the inside surface of the shell, and provides an electrically conducting path with the required electrical time constant of 50 ms. The shell plate will be formed to the required toroidal configuration, after which the poloidal and toroidal flanges will be welded to the structure and machined. The Inconel vacuum vessel consists of bellows segments, armor support rings, and diagnostic stations welded together to form the complete vacuum vessel assembly. The necessity for accurate positioning of the vacuum vessel within the shell requires that the shell and vacuum vessel be fabricated with major diameter tolerances within 0.050-in. true position of the nominal diameters of 188.0-in. and 188.820-in., respectively. 7 figs
Indirect evidences for a gas/dust torus along the Phobos orbit
International Nuclear Information System (INIS)
Dubinin, E.M.; Lundin, R.; Pissarenko, N.F.; Barabash, S.V.; Zakharov, A.V.; Koskinen, H.; Schwingenshuh, K.; Yeroshenko, Ye.G.
1990-01-01
Observations from the PHOBOS-2 space-craft of plasma and magnetic field effects in the solar wind near Mars suggest that a neutral gas (dust?)torus/ring resides along the orbit of the Martian satellite Phobos. Magnetic cavities (strong decreases of the magnetic field strength) coincident with strong plasma density increases (up to a factor of ten) are observed during the first elliptic transition orbits when the spacecraft approached the Phobos orbits. The characteristic transverse dimension of the structures along the spacecraft orbit is in the range 100-1,000 km. Torus effects also have characteristics similar to the formation of a bow shock with increases of plasma density and ion temperature, and a characteristic deflection of the ion flow. This suggests a rather strong interaction between the solar wind plasma and plasma near Phobos orbit. The interaction appears quite similar to that of the solar wind with a comet. The outgassing of matter from Phobos (and Deimos) is also suggested by plasma observations in the wake/tail of the Martian satellites. Altogether, the authors observations imply that a neutral gas cloud - possibly also associated with a faint dust ring - exists along the Phobos orbit
The theory of pseudo-differential operators on the noncommutative n-torus
Tao, J.
2018-02-01
The methods of spectral geometry are useful for investigating the metric aspects of noncommutative geometry and in these contexts require extensive use of pseudo-differential operators. In a foundational paper, Connes showed that, by direct analogy with the theory of pseudo-differential operators on finite-dimensional real vector spaces, one may derive a similar pseudo-differential calculus on noncommutative n-tori, and with the development of this calculus came many results concerning the local differential geometry of noncommutative tori for n=2,4, as shown in the groundbreaking paper in which the Gauss-Bonnet theorem on the noncommutative two-torus is proved and later papers. Certain details of the proofs in the original derivation of the calculus were omitted, such as the evaluation of oscillatory integrals, so we make it the objective of this paper to fill in all the details. After reproving in more detail the formula for the symbol of the adjoint of a pseudo-differential operator and the formula for the symbol of a product of two pseudo-differential operators, we extend these results to finitely generated projective right modules over the noncommutative n-torus. Then we define the corresponding analog of Sobolev spaces and prove equivalents of the Sobolev and Rellich lemmas.
X-ray production experiments on the RACE Compact Torus Accelerator
International Nuclear Information System (INIS)
Hammer, J.H.; Eddleman, J.L.; Hartman, C.W.; McLean, H.S.; Molvik, A.W.; Gee, M.
1989-12-01
The Purpose of the Compact Torus Accelerator (CTA) program at LLNL is to prove the principle of a unique accelerator concept based on magnetically confined compact torus (CT) plasma rings and to study applications. Successful achievement of these goals could lead to a high power-density driver for many applications including an intense x-ray source for nuclear weapons effects simulation and an inertial fusion driver. Fusion applications and a description of the CTA concept are included in a companion paper at this conference. This paper will describe the initial experiments on soft x-ray production conducted on the plasma Ring ACcelerator Experiment (RACE) and compare the results to modeling studies. The experiments on CT stagnation and soft x-ray production were conducted with unfocused rings as a first of CT dynamics and the physics of x-ray production. The x-ray fluences observed are consistent with expectations based on calculations employing a radiation-hydrodynamics code. We conclude with a diffusion of future x-ray production studies that can be conducted on RACE and a possible multi-megajoule upgrade
AN OCCULTATION EVENT IN CENTAURUS A AND THE CLUMPY TORUS MODEL
Energy Technology Data Exchange (ETDEWEB)
Rivers, Elizabeth; Markowitz, Alex; Rothschild, Richard, E-mail: erivers@ucsd.edu [Center for Astrophysics and Space Sciences, University of California, San Diego, 9500 Gilman Drive, La Jolla, CA 92093-0424 (United States)
2011-12-15
We have analyzed 16 months of sustained monitoring observations of Centaurus A from the Rossi X-Ray Timing Explorer to search for changes in the absorbing column in the line of sight to the central nucleus. We present time-resolved spectroscopy which indicates that a discrete clump of material transited the line of sight to the central illuminating source over the course of {approx}170 days between 2010 August and 2011 February with a maximum increase in the column density of about 8.4 Multiplication-Sign 10{sup 22} cm{sup -2}. This is the best quality data of such an event that has ever been analyzed with the shape of the ingress and egress clearly seen. Modeling the clump of material as roughly spherical with a linearly decreasing density profile and assuming a distance from the central nucleus commensurate with the dusty torus, we found that the clump would have a diameter of (1.4-2.4) Multiplication-Sign 10{sup 15} cm with a central number density of n{sub H} = (1.8-3.0) Multiplication-Sign 10{sup 7} cm{sup -3}. This is consistent with previous results for a similar (though possibly much longer) occultation event inferred in this source in 2003-2004 and supports models of the molecular torus as a clumpy medium.
AN OCCULTATION EVENT IN CENTAURUS A AND THE CLUMPY TORUS MODEL
International Nuclear Information System (INIS)
Rivers, Elizabeth; Markowitz, Alex; Rothschild, Richard
2011-01-01
We have analyzed 16 months of sustained monitoring observations of Centaurus A from the Rossi X-Ray Timing Explorer to search for changes in the absorbing column in the line of sight to the central nucleus. We present time-resolved spectroscopy which indicates that a discrete clump of material transited the line of sight to the central illuminating source over the course of ∼170 days between 2010 August and 2011 February with a maximum increase in the column density of about 8.4 × 10 22 cm –2 . This is the best quality data of such an event that has ever been analyzed with the shape of the ingress and egress clearly seen. Modeling the clump of material as roughly spherical with a linearly decreasing density profile and assuming a distance from the central nucleus commensurate with the dusty torus, we found that the clump would have a diameter of (1.4-2.4) × 10 15 cm with a central number density of n H = (1.8-3.0) × 10 7 cm –3 . This is consistent with previous results for a similar (though possibly much longer) occultation event inferred in this source in 2003-2004 and supports models of the molecular torus as a clumpy medium.
The Ionization Fraction in the Obscuring ``Torus'' of an Active Galactic Nucleus
Wilson, A. S.; Roy, A. L.; Ulvestad, J. S.; Colbert, E. J. M.; Weaver, K. A.; Braatz, J. A.; Henkel, C.; Matsuoka, M.; Xue, S.; Iyomoto, N.; Okada, K.
1998-10-01
The LINER galaxy NGC 2639 contains a water vapor megamaser, suggesting the presence of a nuclear accretion disk or torus viewed close to edge-on. This galaxy is thus a good candidate for revealing absorption by the torus of any compact nuclear continuum emission. In this paper, we report VLBA radio maps at three frequencies and an ASCA X-ray spectrum obtained to search for free-free and photoelectric absorptions, respectively. The radio observations reveal a compact (~1.3 × 10-5, which is comparable to the theoretical upper limit derived by Neufeld, Maloney, and Conger for X-ray heated molecular gas. The two values may be reconciled if the molecular gas is very dense: nH2>~109 cm-3. The measured ionization fraction is also consistent with the idea that both absorptions occur in a hot (~6000 K), weakly ionized (ionization fraction a few times 10-2) atomic region that may coexist with the warm molecular gas. If this is the case, the absorbing gas is ~1 pc from the nucleus. We rule out the possibility that both absorptions occur in a fully ionized gas near 104 K. If our line of sight passes through more than one phase, the atomic gas probably dominates the free-free absorption, while the molecular gas may dominate the photoelectric absorption.
Energy Technology Data Exchange (ETDEWEB)
Juárez, Rafael, E-mail: rjuarez@ind.uned.es [Departamento de Ingeniería Energética, ETSII-UNED, Calle Juan del Rosal 12, Madrid 28040 (Spain); Pampin, Raul [F4E, Torres Diagonal Litoral B3, Josep Pla 2, Barcelona 08019 (Spain); Levesy, Bruno [ITER Organization, 13115 Route de Vinon sur Verdon, St Paul Lez Durance (France); Moro, Fabio [ENEA, Via Enrico Fermi 45, Frascati, Rome (Italy); Suarez, Alejandro [ITER Organization, 13115 Route de Vinon sur Verdon, St Paul Lez Durance (France); Sanz, Javier [Departamento de Ingeniería Energética, ETSII-UNED, Calle Juan del Rosal 12, Madrid 28040 (Spain)
2015-11-15
Shutdown dose rates for planned maintenance purposes is an active research field in ITER. In this work the radiation (neutron and gamma) cross-talk between ports in the most conservative case foreseen in ITER is investigated: the presence of a torus cryopump lower port, mostly empty for pumping efficiency reasons. There will be six of those ports: #4, #6, #10, #12, #16 and #18. The equatorial ports placed above them will receive a significant amount of additional radiation affecting the shutdown dose rates during in situ maintenance activities inside the cryostat, and particularly in the port interspace area. In this study a general situation to all the equatorial ports placed above torus cryopump lower ports is considered: a generic diagnostics equatorial port placed above the torus cryopump lower port (LP#4). In terms of shutdown dose rates at equatorial port interspace after 10{sup 6} s of cooling time, 405 μSv/h has been obtained, of which 160 μSv/h (40%) are exclusively due to radiation cross-talk from a torus cryopump lower port. Equatorial port activation due to only “local neutrons” contributes 166 μSv/h at port interspace, showing that radiation cross-talk from such a lower port is a phenomenon comparable in magnitude to the neutron leakage though the equatorial port plug.
Ulysses Radio Occultation Observations of the lo Plasma Torus During the Jupiter Encounter.
Bird, M K; Asmar, S W; Brenkle, J P; Edenhofer, P; Funke, O; Pätzold, M; Volland, H
1992-09-11
Radio signals from Ulysses were used to probe the lo plasma torus (IPT) shortly after the spacecraft's closest approach to Jupiter. The frequencies of the two downlinks at S-band (2.3 gigahertz) and X-band (8.4 gigahertz) were recorded, differenced, and integrated in order to derive the columnar electron density of the IPT. The measurements agree qualitatively with contemporary models of the IPT based on Voyager data, but significant differences are apparent as well. The overall level of the IPT electron density is approximately the same as the prediction, implying that the amount of gas (or plasma) injected from lo is similar to that observed during the Voyager era. On the other hand, the IPT seems to be less extended out of the centrifugal equator, implying a smaller plasma temperature than predicted.
Spectral and correlation analysis of soft X-ray signals from the Joint European Torus tokamak
International Nuclear Information System (INIS)
Karlsson, J.; Pazsit, I.
1997-01-01
Tomographic methods applied to soft X-rays emitted from a fusion plasma have long been used to diagnose and interpret magnetohydrodynamic and other plasma activities. However, fluctuation analysis has recently been proposed as a complementary method to tomography. The novelty of the suggested method is that the various modes can be determined without tomographic inversion. This paper reports on the results of correlation and spectral analysis of soft X-ray data. The seven measurements analyzed were made by the Joint European Torus (JET) Joint Undertaking using their old soft X-ray measurement system. Auto power spectral densities and phase relations were evaluated from the measured signals as functions of the lines of sight. The fundamental mode m=n=1 was identified in several measurements. The corresponding frequency and toroidal rotation velocity were determined. Higher order modes were also observed and identified. Furthermore, simple model calculations were performed and the results compared with evaluated auto-spectra. (orig.)
International Nuclear Information System (INIS)
Kugel, H.; Bell, M.; Ahn, J.W.; Bush, C.E.; Maingi, R.
2008-01-01
National Spherical Torus Experiment (which M. Ono, Nucl. Fusion 40, 557 (2000)) high-power divertor plasma experiments have shown, for the first time, that benefits from lithium coatings applied to plasma facing components found previously in limited plasmas can occur also in high-power diverted configurations. Lithium coatings were applied with pellets injected into helium discharges, and also with an oven that directed a collimated stream of lithium vapor toward the graphite tiles of the lower center stack and divertor. Lithium oven depositions from a few milligrams to 1 g have been applied between discharges. Benefits from the lithium coatings were sometimes, but not always, seen. These benefits sometimes included decreases in plasma density, inductive flux consumption, and edge-localized mode occurrence, and increases in electron temperature, ion temperature, energy confinement, and periods of edge and magnetohydrodynamic quiescence. In addition, reductions in lower divertor D, C, and O luminosity were measured.
Multi-Point Thomson Scattering Diagnostic for the Helicity Injected Torus
Liptac, J. E.; Smith, R. J.; Hoffman, C. S.; Jarboe, T. R.; Nelson, B. A.; Leblanc, B. P.; Phillips, P.
1999-11-01
The multi-point Thomson scattering system on the Helicity Injected Torus--II can determine electron temperature and density at 11 radial positions at a single time during the plasma discharge. The system includes components on loan from both PPPL and from the University of Texas. The collection optics and Littrow spectrometer from Princeton, and the 1 GW laser and multi-anode microchannel plate detector from Texas have been integrated into a compact structure, creating a mobile and reliable diagnostic. The mobility of the system allows alignment to occur in a room adjacent to the experiment, greatly reducing the disturbance to normal machine operation. The four main parts of the Thomson scattering system, namely, the laser, the beam line, the collection optics, and the mobile structure are presented and discussed.
Study of plasma confinement in ELMO Bumpy Torus with a heavy-ion beam probe
Energy Technology Data Exchange (ETDEWEB)
Bieniosek, F. M.
1981-01-01
Plasma confinement in ELMO Bumpy Torus (EBT) is generally strongly dependent on an ambipolar electric field. Spatially resolved measurements of the resulting electric space potential phi/sub sp/ have been made in a single plasma cross section by the heavy-ion beam probe. This diagnostic injects a 4-60-keV beam of (usually) Cs/sup +/ ions into the plasma. Measurement of the energy of Cs/sup 2 +/ secondary ions leaving the plasma gives a continuous monitor of the local space potential. In addition, the total detected Cs/sup 2 +/ ion current is proportional to the product of the local electron density and the ionization rate, which, in turn, is a function of the electron temperature. This signal, nf(T/sub e/), is sensitive to all three electron distributions found in EBT - those of the cold surface plasma, the warm core plasma, and the hot electron ring.
Study of plasma confinement in ELMO Bumpy Torus with a heavy-ion beam probe
International Nuclear Information System (INIS)
Bieniosek, F.M.
1981-01-01
Plasma confinement in ELMO Bumpy Torus (EBT) is generally strongly dependent on an ambipolar electric field. Spatially resolved measurements of the resulting electric space potential phi/sub sp/ have been made in a single plasma cross section by the heavy-ion beam probe. This diagnostic injects a 4-60-keV beam of (usually) Cs + ions into the plasma. Measurement of the energy of Cs 2+ secondary ions leaving the plasma gives a continuous monitor of the local space potential. In addition, the total detected Cs 2+ ion current is proportional to the product of the local electron density and the ionization rate, which, in turn, is a function of the electron temperature. This signal, nf(T/sub e/), is sensitive to all three electron distributions found in EBT - those of the cold surface plasma, the warm core plasma, and the hot electron ring
Acceleration of compact torus plasma rings in a coaxial rail-gun
International Nuclear Information System (INIS)
Hartman, C.W.; Hammer, J.H.; Eddleman, J.
1985-01-01
We discuss here theoretical studies of magnetic acceleration of Compact Torus plasma rings in a coaxial, rail-gun accelerator. The rings are formed using a magnetized coaxial plasma gun and are accelerated by injection of B/sub theta/ flux from an accelerator bank. After acceleration, the rings enter a focusing cone where the ring is decelerated and reduced in radius. As the ring radius decreases, the ring magnetic energy increases until it equals the entering kinetic energy and the ring stagnates. Scaling laws and numerical calculations of acceleration using a O-D numerical code are presented. 2-D, MHD simulations are shown which demonstrate ring formation, acceleration, and focusing. Finally, 3-D calculations are discussed which determine the ideal MHD stability of the accelerated ring
TOPIC: a debugging code for torus geometry input data of Monte Carlo transport code
International Nuclear Information System (INIS)
Iida, Hiromasa; Kawasaki, Hiromitsu.
1979-06-01
TOPIC has been developed for debugging geometry input data of the Monte Carlo transport code. the code has the following features: (1) It debugs the geometry input data of not only MORSE-GG but also MORSE-I capable of treating torus geometry. (2) Its calculation results are shown in figures drawn by Plotter or COM, and the regions not defined or doubly defined are easily detected. (3) It finds a multitude of input data errors in a single run. (4) The input data required in this code are few, so that it is readily usable in a time sharing system of FACOM 230-60/75 computer. Example TOPIC calculations in design study of tokamak fusion reactors (JXFR, INTOR-J) are presented. (author)
Wavepacket propagation and current startup near the lower hybrid frequency in the torus
International Nuclear Information System (INIS)
Ohkubo, K.; Matsumura, Y.; Mizuno, M.; Matsuoka, M.; Matsuura, K.
1987-08-01
In addition to the two-dimensional propagation of wavepacket, electron heating and current drive by a lower hybrid wave in afterglow plasmas are investigated in a small torus. Because the wavepacket, which has a wide frequency spectrum, spreads in space and time due to dispersion, the pulse width of a received wavepacket accompanied with frequency shift increases. The experimental results including the direct observed group and phase velocities agree with the theoretical analysis. Lower hybrid waves with low power ( < 10 W and ≅ 100 μs) above the threshold power (≅ 0.3 W) are observed which heat electrons and drive the toroidal current. The power threshold is related to the power dependence on parametric instability. It is pointed out that parametrically excited lower hybrid waves take part in both electron heating and filling up the spectral gap which is closely related to current startup. (author)
Scintillator Based Energetic Ion Loss Diagnostic for the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Darrow, D.S.
2007-01-01
A scintillator based energetic ion loss detector has been built and installed on the National Spherical Torus Experiment (NSTX) to measure the loss of neutral beam ions. The detector is able to resolve the pitch angle and gyroradius of the lost energetic ions. It has a wide acceptance range in pitch angle and energy, and is able to resolve the full, one-half, and one-third energy components of the 80 keV D neutral beams up to the maximum toroidal magnetic field of NSTX. Multiple Faraday cups have been embedded behind the scintillator to allow easy absolute calibration of the diagnostic and to measure the energetic ion loss to several ranges of pitch angle with good time resolution. Several small, vacuum compatible lamps allow simple calibration of the scintillator position within the field of view of the diagnostic's video camera
Effects of applied dc radial electric fields on particle transport in a bumpy torus plasma
Roth, J. R.
1978-01-01
The influence of applied dc radial electric fields on particle transport in a bumpy torus plasma is studied. The plasma, magnetic field, and ion heating mechanism are operated in steady state. Ion kinetic temperature is more than a factor of ten higher than electron temperature. The electric fields raise the ions to energies on the order of kilovolts and then point radially inward or outward. Plasma number density profiles are flat or triangular across the plasma diameter. It is suggested that the radial transport processes are nondiffusional and dominated by strong radial electric fields. These characteristics are caused by the absence of a second derivative in the density profile and the flat electron temperature profiles. If the electric field acting on the minor radius of the toroidal plasma points inward, plasma number density and confinement time are increased.
Scintillator Based Energetic Ion Loss Diagnostic for the National Spherical Torus Experiment
Energy Technology Data Exchange (ETDEWEB)
D.S. Darrow
2007-07-02
A scintillator based energetic ion loss detector has been built and installed on the National Spherical Torus Experiment (NSTX) to measure the loss of neutral beam ions. The detector is able to resolve the pitch angle and gyroradius of the lost energetic ions. It has a wide acceptance range in pitch angle and energy, and is able to resolve the full, one-half, and one-third energy components of the 80 keV D neutral beams up to the maximum toroidal magnetic field of NSTX. Multiple Faraday cups have been embedded behind the scintillator to allow easy absolute calibration of the diagnostic and to measure the energetic ion loss to several ranges of pitch angle with good time resolution. Several small, vacuum compatible lamps allow simple calibration of the scintillator position within the field of view of the diagnostic's video camera.
Spectroscopic study of turbulent heating in the high beta tokamak - Torus II
International Nuclear Information System (INIS)
Georgiou, G.E.
1979-01-01
Visible spectroscopy, involving line profile and line intensity measurements, was used to study the turbulent heating of the rectangular cross-section high-beta tokamak Torus II. The spectroscopy was done in the visible wave-length region using a six channel polychrometer having 0.2 A resolution, which is capable of radial scans of the plasma. The plasma, obtained by ionizing helium, is heated by poloidal skin currents, induced by a rapid (tau/sub R/ approx. = 1.7 μsec) change of the toroidal magnetic field either parallel or anti-parallel to the initial toroidal bias magnetic field, which converts a cold toroidal Z-pinch plasma into a hot tokamak plasma
International Nuclear Information System (INIS)
Gates, D.A.; Ferron, J.R.; Bell, M.; Gibney, T.; Johnson, R.; Marsala, R.J.; Mastrovito, D.; Menard, J.E.; Mueller, D.; Penaflor, B.; Sabbagh, S.A.; Stevenson, T.
2005-01-01
Plasma shape control using real-time equilibrium reconstruction has been implemented on the National Spherical Torus Experiment (NSTX). The rtEFIT code originally developed for use on DIII-D was adapted for use on NSTX. The real-time equilibria provide calculations of the flux at points on the plasma boundary, which is used as input to a shape control algorithm known as isoflux control. The flux at the desired boundary location is compared to a reference flux value, and this flux error is used as the basic feedback quantity for the poloidal-field coils on NSTX. The hardware that comprises the control system is described, as well as the software infrastructure. Examples of precise boundary control are also presented
Unified Ideal Stability Limits for Advanced Tokamak and Spherical Torus Plasmas
International Nuclear Information System (INIS)
Menard, J.E.; Bell, M.G.; Bell, R.E.; Gates, D.A.; Kaye, S.M.; LeBlanc, B.P.; Sabbagh, S.A.; Fredrickson, E.D.; Jardin, S.C.; Maingi, R.; Manickam, J.; Mueller, D.; Ono, M.; Paoletti, F.; Peng, Y.-K.M.; Soukhanovskii, V.; Stutman, D.; Synakowski, E.J.
2003-01-01
Ideal magnetohydrodynamic stability limits of shaped tokamak plasmas with high bootstrap fraction are systematically determined as a function of plasma aspect ratio. For plasmas with and without wall stabilization of external kink modes, the computed limits are well described by distinct and nearly invariant values of a normalized beta parameter utilizing the total magnetic field energy density inside the plasma. Stability limit data from the low aspect ratio National Spherical Torus Experiment is compared to these theoretical limits and indicates that ideal nonrotating plasma no-wall beta limits have been exceeded in regimes with sufficiently high cylindrical safety factor. These results could impact the choice of aspect ratio in future fusion power plants
FIREBIRD - a conceptual design of a field reversed configuration compact torus fusion reactor (CTFR)
International Nuclear Information System (INIS)
Raman, R.; Zubrin, R.M.
1987-01-01
This paper is a summary of the work carried out by the Nuclear Engineering 512 design team at the University of Washington on a conceptual design study of a Compact-Torus (Field-Reversed) Fusion Reactor Configuration (CTFR). The primary objective of the study was to develop a reactor design that strived for high engineering power density, modest recirculating power and competitive cost of electrical power. A Conceptual design was developed for a translating field-reversed configuration reactor; based on the Physics developed by Tuszewski and Lindford at LANL and by Hoffman and Milroy at MSNW. Furthermore, it also appears possible to operate a simplified form of this reactor using a pure D-D fuel cycle after an initial D-T ignition ramp to reach the advanced fuel operating regime. One optimistic reactor so designed has a length of about 35 meters, producing a net electrical power of about 375 MWe
Progress towards Steady State at Low Aspect Ratio on the National Spherical Torus Experiment (NSTX)
International Nuclear Information System (INIS)
Gates, D.A.; Menard, J.; Maingi, R.; Kaye, S.; Sabbagh, S.A.; Diem, S.; Wilson, J.R.; Bell, M.G.; Bell, R.E.; Ferron, J.; Fredrickson, E.D.; Kessel, C.E.; LeBlanc, B.P.; Levinton, F.; Manickam, J.; Mueller, D.; Raman, R.; Stevenson, T.; Stutman, D.; Taylor, G.; Tritz, K.; Yu, H.
2007-01-01
Modifications to the plasma control capabilities and poloidal field coils of the National Spherical Torus Experiment (NSTX) have enabled a significant enhancement in shaping capability which has led to the transient achievement of a record shape factor (S (triple b ond) q 95 (I p /aB t )) of ∼ 41 (MA m -1 T -1 ) simultaneous with a record plasma elongation of κ (triple b ond) b/a ∼ 3. This result was obtained using isoflux control and real-time equilibrium reconstruction. Achieving high shape factor together with tolerable divertor loading is an important result for future ST burning plasma experiments as exemplified by studies for future ST reactor concepts, as well as neutron producing devices, which rely on achieving high shape factors in order to achieve steady state operation while maintaining MHD stability. Statistical evidence is presented which demonstrates the expected correlation between increased shaping and improved plasma performance.
Design of the fuel processing loop for the Next European Torus
International Nuclear Information System (INIS)
Kalyanam, K.M.; Sood, S.K.; Kveton, O.K.; Busigin, A.; Adamek, F.; Murdoch, D.K.; Leger, D.; Dinner, P.J.; Iseli, M.
1992-01-01
This paper presents a summary of the results of a detailed design study performed for the Fuel Processing Loop of the Next European Torus (NET). The design is based on the concept of adsorption of impurities on molecular sieve at liquid nitrogen temperature, followed by catalytic oxidation of the regenerated impurities to water, and subsequent reduction of the water by electrolysis. The design study has shown that the process can be engineered using, mostly, available components, and can be designed to be safe. Special design features to make the process passively safe are described. The results of a preliminary safety analysis are summarized. Tritium inventories in the various sections of the process loops are shown. A cost estimate for the overall process system is also presented
Acceleration of compact torus plasma rings in a coaxial rail-gun
International Nuclear Information System (INIS)
Hartman, C.W.; Hammer, J.H.; Eddleman, J.
1986-01-01
They discuss here theoretical studies of magnetic acceleration of Compact Torus plasma rings in a coaxial, rail-gun accelerator. The rings are formed using a magnetized coaxial plasma gun and are accelerated by injection of B/sub Theta/ flux from an accelerator bank. After acceleration, the rings enter a focusing cone where the ring is decelerated and reduced in radius. As the ring radius decreases, the ring magnetic energy increases until it equals the entering kinetic energy and the ring stagnates. Scaling laws and numerical calculations of acceleration using a O-D numerical code are presented. 2-D, MHD simulations are shown which demonstrate ring formation, acceleration, and focusing. Finally, 3-D calculations are discussed which determine the ideal MHD stability of the accelerated ring
Transmutation of minor actinides in a spherical torus tokamak fusion reactor, FDTR
International Nuclear Information System (INIS)
Feng, K.M.; Zhang, G.S.; Deng, M.G.
2003-01-01
In this paper, a concept for the transmutation of minor actinide (MA) nuclear wastes based on a spherical torus (ST) tokamak reactor, FDTR, is put forward. A set of plasma parameters suitable for the transmutation blanket was chosen. The 2-D neutron transport code TWODANT, the 3-D Monte Carlo code MCNP/4B, the 1-D neutron transport and burn-up calculation code BISON3.0 and their associated data libraries were used to calculate the transmutation rate, the energy multiplication factor and the tritium breeding ratio of the transmutation blanket. The calculation results for the system parameters and the actinide series isotopes for different operation times are presented. The engineering feasibility of the center-post (CP) of FDTR has been investigated and the results are also given. A preliminary neutronics calculation based on an ST transmutation blanket shows that the proposed system has a high transmutation capability for MA wastes. (author)
Compact torus equilibria set up in the rotamak by rotating magnetic fields
International Nuclear Information System (INIS)
Storer, R.G.
1983-01-01
In the Rotamak, a rotating magnetic field is used to drive a steady toroidal current in a compact torus device. High power, short duration (approx.=80 μs) and low power, long duration experiments (approx.=3 ms) have been studied. In both of these experiments a steady phase exists which is well described by the assumption that the plasma is in an averaged magnetohydrodynamic pressure balance situation. Using a model based on this assumption, self-consistency imposes conditions relating the temperature and density of the plasma to the steady components of the internal magnetic fields. In the high power experiment, this steady phase evolves into a second steady phase, with lower toroidal current, which has a #betta#=1, mirror-like configuration which also appears to satisfy local pressure balance but with the magnetic axis (minimum of the poloidal flux) at the centre of the spherical vessel. (orig.)
Reflectometry and transport in thermonuclear plasmas in the Joint European Torus
International Nuclear Information System (INIS)
Sips, A.C.C.
1991-01-01
The subjects of this thesis are the study of microwave reflectometry as a method to measure electron density profiles, and the study of particle and energy transport in thermonuclear plasmas. In the transport studies data of a 12-channel reflectometer system are used to analyze the propagation of electron density perturbations in the plasma. The measurements described in this thesis are performed in the plasmas in the Joint European Torus (JET). The main points of study described are based on microwave reflectometry, the principles of which are given. Two modes of operation of a reflectometer are described. Firstly, electro-magnetic waves with constant frequencies may be launched into the plasma to measure variations in the electron density profile. Secondly, the absolute density profile can be measured with a reflectometer, when the source frequencies are swept. (author). 56 refs.; 41 figs.; 5 tabs
Energy Technology Data Exchange (ETDEWEB)
Jaworski, M A; Gray, T K; Kaita, R; Kallman, J; Kugel, H; LeBlanc, B; McLean, A; Sabbagh, S A; Soukanovskii, V; Stotler, D P
2011-06-03
The National Spherical Torus Experiment (NSTX) has recently studied the use of a liquid lithium divertor (LLD). Divertor Langmuir probes have also been installed for making measurements of the local plasma conditions. A non-local probe interpretation method is used to supplement the classical probe interpretation and obtain measurements of the electron energy distribution function (EEDF) which show the occurrence of a hot-electron component. Analysis is made of two discharges within a sequence that exhibited changes in plasma fueling efficiency. It is found that the local electron temperature increases and that this increase is most strongly correlated with the energy contained within the hot-electron population. Preliminary interpretative modeling indicates that kinetic effects are likely in the NSTX.
Nuclear performance calculations for the ELMO Bumpy Torus Reactor (EBTR) reference design
International Nuclear Information System (INIS)
Santoro, R.T.; Barnes, J.M.
1977-12-01
The nuclear performance of the ELMO Bumpy Torus Reactor reference design has been calculated using the one-dimensional discrete ordinates code ANISN and the latest available ENDF/B-IV transport cross-section data and nuclear response functions. The calculated results include estimates of the spatial and integral heating rate with emphasis on the recovery of fusion neutron energy in the blanket assembly and minimization of the energy deposition rates in the cryogenic magnet coil assemblies. The tritium breeding ratio in the natural lithium-laden blanket was calculated to be 1.29 tritium nuclei per incident neutron. The radiation damage in the reactor structural material and in the magnet assembly is also given
A study on conceptual design of tritium production fusion reactor based on spherical torus
International Nuclear Information System (INIS)
He Kaihui; Huang Jinhua
2003-01-01
Conceptual design of an advanced tritium production reactor based on spherical torus (ST), which is an intermediate application of fusion energy, is presented. Different from traditional Tokamak tritium production reactor design, advanced plasma physics performance and compact structural characteristics of ST are used to minimize tritium leakage and to maximize tritium breeding ratio with arrangement of tritium production blankets as possible as it can do within vacuum vessel in order to produce certain amount of excess tritium except self-sufficient plasma core, corresponding plant availability 40% or more. Based on 2D neutronics calculation, preliminary conceptual design of ST-TPR is presented. Based on systematical analysis, design risk, uncertainty and backup are introduced generally for the backgrounds of next detailed conceptual design. (authors)
Realizing "2001: A Space Odyssey": Piloted Spherical Torus Nuclear Fusion Propulsion
Williams, Craig H.; Dudzinski, Leonard A.; Borowski, Stanley K.; Juhasz, Albert J.
2005-01-01
A conceptual vehicle design enabling fast, piloted outer solar system travel was created predicated on a small aspect ratio spherical torus nuclear fusion reactor. The initial requirements were satisfied by the vehicle concept, which could deliver a 172 mt crew payload from Earth to Jupiter rendezvous in 118 days, with an initial mass in low Earth orbit of 1,690 mt. Engineering conceptual design, analysis, and assessment was performed on all major systems including artificial gravity payload, central truss, nuclear fusion reactor, power conversion, magnetic nozzle, fast wave plasma heating, tankage, fuel pellet injector, startup/re-start fission reactor and battery bank, refrigeration, reaction control, communications, mission design, and space operations. Detailed fusion reactor design included analysis of plasma characteristics, power balance/utilization, first wall, toroidal field coils, heat transfer, and neutron/x-ray radiation. Technical comparisons are made between the vehicle concept and the interplanetary spacecraft depicted in the motion picture 2001: A Space Odyssey.
Williams, Craig H.; Borowski, Stanley K.; Dudzinski, Leonard A.; Juhasz, Albert J.
1998-01-01
A conceptual vehicle design enabling fast outer solar system travel was produced predicated on a small aspect ratio spherical torus nuclear fusion reactor. Initial requirements were for a human mission to Saturn with a greater than 5% payload mass fraction and a one way trip time of less than one year. Analysis revealed that the vehicle could deliver a 108 mt crew habitat payload to Saturn rendezvous in 235 days, with an initial mass in low Earth orbit of 2,941 mt. Engineering conceptual design, analysis, and assessment was performed on all ma or systems including payload, central truss, nuclear reactor (including divertor and fuel injector), power conversion (including turbine, compressor, alternator, radiator, recuperator, and conditioning), magnetic nozzle, neutral beam injector, tankage, start/re-start reactor and battery, refrigeration, communications, reaction control, and in-space operations. Detailed assessment was done on reactor operations, including plasma characteristics, power balance, power utilization, and component design.
Conceptual design of tritium production fusion reactor based on spherical torus
International Nuclear Information System (INIS)
He Kaihui; Huang Jinhua
2003-01-01
Conceptual design of an advanced tritium production fusion reactor based on spherical torus, which is intermediate application of fusion energy, was presented in this paper. Differing from the traditional tokamak tritium production reactor design, advanced plasma physics performance and compact structural characteristics of ST were used to minimize tritium leakage and maximize tritium breeding ratio with arrangement of tritium production blankets within vacuum vessel as possible in order to produce 1 kg excess tritium except need of self-sufficient plasma core with 40% or more corresponding plant availability. Based on 2D neutronics calculation, preliminary conceptual design of ST-TPR was presented, providing the backgrounds and reference for next detailed conceptual design
Spectral asymmetry of the massless Dirac operator on a 3-torus
International Nuclear Information System (INIS)
Downes, Robert J.; Vassiliev, Dmitri; Levitin, Michael
2013-01-01
Consider the massless Dirac operator on a 3-torus equipped with Euclidean metric and standard spin structure. It is known that the eigenvalues can be calculated explicitly: the spectrum is symmetric about zero and zero itself is a double eigenvalue. The aim of the paper is to develop a perturbation theory for the eigenvalue with smallest modulus with respect to perturbations of the metric. Here the application of perturbation techniques is hindered by the fact that eigenvalues of the massless Dirac operator have even multiplicity, which is a consequence of this operator commuting with the antilinear operator of charge conjugation (a peculiar feature of dimension 3). We derive an asymptotic formula for the eigenvalue with smallest modulus for arbitrary perturbations of the metric and present two particular families of Riemannian metrics for which the eigenvalue with smallest modulus can be evaluated explicitly. We also establish a relation between our asymptotic formula and the eta invariant
Guiding center simulations of strong ion beams with applications to the Counterstreaming Ion Torus
International Nuclear Information System (INIS)
Tull, C.
1978-03-01
In the proposed Counterstreaming Ion Torus (CIT) steady state rather than pulsed operation may be possible if all of the plasma power density is provided by neutral beam injection. After the neutral beams have penetrated the magnetic field, strong ion beam currents are produced. A major concern with the relatively strong counterstreaming ion currents is the effect of the beam self-magnetic fields on the macroscopic equilibrium of the system. Pinching and self focusing of the individual beams may occur, or the repulsive interaction of the two oppositely directed beam currents may destroy the equilibrium entirely. We investigate this macroscopic behavior of the ion beams with a guiding center plasma particle simulation model and we describe a model we have developed to simulate steady state behavior in an ideal CIT configuration
Numerical study of two-fluid flowing equilibria of helicity-driven spherical torus plasmas
International Nuclear Information System (INIS)
Kanki, T.; Nagata, M.; Uyama, T.
2004-01-01
Two-fluid flowing equilibrium configurations of a helicity-driven spherical torus (HD-ST) are numerically determined by using the combination of the finite difference and the boundary element methods. It is found from the numerical results that electron fluids near the central conductor are tied to an external toroidal field and ion fluids are not. The magnetic configurations change from the high-q HD-ST (q>1) with paramagnetic toroidal field and low-β (volume average β value, ∼ 2%) through the helicity-driven spheromak and RFP (reverse field pinch) to the ultra low-q HD-ST (0 ∼ 18%) as the external toroidal field at the inner edge regions decreases and reverses the sign. The two-fluid effects are more significant in this equilibrium transition when the ion diamagnetic drift is dominant in the flowing two-fluid. (authors)
The control system for the multiple-pellet injector on the Joint European Torus
International Nuclear Information System (INIS)
Baylor, L.R.; Jernigan, T.C.; Stewart, K.A.
1989-01-01
A stand-alone control and data acquisition system for the Oak Ridge National Laboratory (ORNL) multiple-pellet injector installed on the Joint European Torus (JET) has been designed and installed with the injector. This system, which is based on a MicroVAX II computer and a programmable logic controller (PLC), is an upgrade of previous systems designed for ORNL pellet injectors installed on other fusion experiments. The primary control system upgrades are in the user interface, in the automation of sequential injector operation, and in the analysis of the transient data acquired for each pellet fired. The system is integrated into the JET CODAS environment through CAMAC communications modules with customized communications software. Routine operation of the injector is automated and requires no operator intervention. Details of the hardware and software design and the operation of the system are presented in this paper. 4 refs., 3 figs
Trial wave functions for a composite Fermi liquid on a torus
Fremling, M.; Moran, N.; Slingerland, J. K.; Simon, S. H.
2018-01-01
We study the two-dimensional electron gas in a magnetic field at filling fraction ν =1/2 . At this filling the system is in a gapless state which can be interpreted as a Fermi liquid of composite fermions. We construct trial wave functions for the system on a torus, based on this idea, and numerically compare these to exact wave functions for small systems found by exact diagonalization. We find that the trial wave functions give an excellent description of the ground state of the system, as well as its charged excitations, in all momentum sectors. We analyze the dispersion of the composite fermions and the Berry phase associated with dragging a single fermion around the Fermi surface and comment on the implications of our results for the current debate on whether composite fermions are Dirac fermions.
Simulation and design of feedback control on resistive wall modes in Keda Torus eXperiment
International Nuclear Information System (INIS)
Li, Chenguang; Liu, Wandong; Li, Hong
2014-01-01
The feedback control of resistive wall modes (RWMs) in Keda Torus eXperiment (KTX) (Liu et al., Plasma Phys. Controlled Fusion 56, 094009 (2014)) is investigated by simulation. A linear model is built to describe the growth of the unstable modes in the absence of feedback and the resulting mode suppression due to feedback, given the typical reversed field pinch plasma equilibrium. The layout of KTX with two shell structures (the vacuum vessel and the stabilizing shell) is taken into account. The feedback performance is explored both in the scheme of “clean mode control” (Zanca et al., Nucl. Fusion 47, 1425 (2007)) and “raw mode control.” The discrete time control model with specific characteristic times will mimic the real feedback control action and lead to the favored control cycle. Moreover, the conceptual design of feedback control system is also presented, targeting on both RWMs and tearing modes
Energy Technology Data Exchange (ETDEWEB)
Kim, YooSung; Shi, Yue-Jiang, E-mail: yjshi@snu.ac.kr; Yang, Jeong-hun; Kim, SeongCheol; Kim, Young-Gi; Dang, Jeong-Jeung; Yang, Seongmoo; Jo, Jungmin; Chung, Kyoung-Jae [Department of Nuclear Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Oh, Soo-Ghee [Division of Energy Systems Research, Ajou University, Suwon 442-749 (Korea, Republic of); Hwang, Y. S. [Department of Nuclear Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Center for Advanced Research in Fusion Reactor Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of)
2016-11-15
Electron density profiles of versatile experiment spherical torus plasmas are measured by using a hydrogen line intensity ratio method. A fast-frame visible camera with appropriate bandpass filters is used to detect images of Balmer line intensities. The unique optical system makes it possible to take images of H{sub α} and H{sub β} radiation simultaneously, with only one camera. The frame rate is 1000 fps and the spatial resolution of the system is about 0.5 cm. One-dimensional local emissivity profiles have been obtained from the toroidal line of sight with viewing dumps. An initial result for the electron density profile is presented and is in reasonable agreement with values measured by a triple Langmuir probe.
International Nuclear Information System (INIS)
Stoneking, M.R.; Lanier, N.E.; Prager, S.C.; Sarff, J.S.; Sinitsyn, D.
1997-01-01
Current profile control is employed in the Madison Symmetric Torus [R. N. Dexter et al., Fusion Technol. 19, 131 (1991)] reversed field pinch to reduce the magnetic fluctuations responsible for anomalous transport. An inductive poloidal electric-field pulse is applied in the sense to flatten the parallel current profile, reducing the dynamo fluctuation amplitude required to sustain the equilibrium. This technique demonstrates a substantial reduction in fluctuation amplitude (as much as 50%), and improvement in energy confinement (from 1 to 5 ms); a record low fluctuation (0.8%) and record high temperature (615 eV) for this device were observed simultaneously during current drive experiments. Plasma beta increases by 50% and the Ohmic input power is three times lower. Particle confinement improves and plasma impurity contamination is reduced. The results of the transient current drive experiments provide motivation for continuing development of steady-state current profile control strategies for the reversed field pinch. copyright 1997 American Institute of Physics
National Spherical Torus Experiment Real Time Plasma Control Data Acquisition Hardware
International Nuclear Information System (INIS)
R.J. Marsala; J. Schneider
2002-01-01
The National Spherical Torus Experiment (NSTX) is currently providing researchers data on low aspect-ratio toroidal plasmas. NSTX's Plasma Control System adjusts the firing angles of thyristor rectifier power supplies, in real time, to control plasma position, shape and density. A Data Acquisition system comprised of off-the-shelf and custom hardware provides the magnetic diagnostics data required in calculating firing angles. This VERSAmodule Eurocard (VME) bus-based system utilizes Front Panel Data Port (FPDP) for high-speed data transfer. Data coming from physically different locations is referenced to several different ground potentials necessitating the need for a custom FPDP multiplexer. This paper discusses the data acquisition system configuration, the in-house designed 4-to-1 FPDP Input Multiplexing Module (FIMM), and future expansion plans
Simplest bifurcation diagrams for monotone families of vector fields on a torus
Baesens, C.; MacKay, R. S.
2018-06-01
In part 1, we prove that the bifurcation diagram for a monotone two-parameter family of vector fields on a torus has to be at least as complicated as the conjectured simplest one proposed in Baesens et al (1991 Physica D 49 387–475). To achieve this, we define ‘simplest’ by sequentially minimising the numbers of equilibria, Bogdanov–Takens points, closed curves of centre and of neutral saddle, intersections of curves of centre and neutral saddle, Reeb components, other invariant annuli, arcs of rotational homoclinic bifurcation of horizontal homotopy type, necklace points, contractible periodic orbits, points of neutral horizontal homoclinic bifurcation and half-plane fan points. We obtain two types of simplest case, including that initially proposed. In part 2, we analyse the bifurcation diagram for an explicit monotone family of vector fields on a torus and prove that it has at most two equilibria, precisely four Bogdanov–Takens points, no closed curves of centre nor closed curves of neutral saddle, at most two Reeb components, precisely four arcs of rotational homoclinic connection of ‘horizontal’ homotopy type, eight horizontal saddle-node loop points, two necklace points, four points of neutral horizontal homoclinic connection, and two half-plane fan points, and there is no simultaneous existence of centre and neutral saddle, nor contractible homoclinic connection to a neutral saddle. Furthermore, we prove that all saddle-nodes, Bogdanov–Takens points, non-neutral and neutral horizontal homoclinic bifurcations are non-degenerate and the Hopf condition is satisfied for all centres. We also find it has four points of degenerate Hopf bifurcation. It thus provides an example of a family satisfying all the assumptions of part 1 except the one of at most one contractible periodic orbit.
Heavy ion beam study of potential formation in bumpy torus plasma
International Nuclear Information System (INIS)
Takasugi, Keiichi.
1985-01-01
A heavy ion beam probe is constructed for the study of plasma confinement in Nagoya Bumpy Torus (NBT-1/1M). The measurement of the local plasma potential as well as the electron density profile is possible with good spatial (1 -- 2 cm) and temporal (-- 1 msec) resolutions. The feedback controlled detection technique and the time resolved fast detection technique are coupled to use, which enables us to measure local potential reliably even in the pulsed experiments. The process of the devlopment of concentric equipotential surface is observed. The cold and collisional plasma in bumpy torus is not in the equilibrium (C-mode), and the vertically polarized potential profile is produced by the toroidal drift. With the growth of warm collisionless electron component, the polarization is poloidally short-circuited, and the concentric equipotential surface is developed. The concentric negative potential well and its positive rim are observed in the standard operation. The position of the potential boundary (rim) moves with the second harmonic ECRH zone at the midplane of each mirror section, where the hot electron ring exists. The rim potential is formed by the direct loss of warm electrons. It is confirmed that the core electron heating is essential for the negative potential formation. The potential depth is much larger than the ion temperature Tsub(i), and cannot be explained by the existing neoclassical theory. A stable positive potential is observed near T-M transition. The positive potential is also observed in the ion heated plasma. Relating to the growth of the high energy component, the potential formation due to direct loss process is discussed. (author)
Finite element analysis of an inflatable torus considering air mass structural element
Gajbhiye, S. C.; Upadhyay, S. H.; Harsha, S. P.
2014-01-01
Inflatable structures, also known as gossamer structures, are at high boom in the current space technology due to their low mass and compact size comparing to the traditional spacecraft designing. Internal pressure becomes the major source of strength and rigidity, essentially stiffen the structure. However, inflatable space based membrane structure are at high risk to the vibration disturbance due to their low structural stiffness and material damping. Hence, the vibration modes of the structure should be known to a high degree of accuracy in order to provide better control authority. In the past, most of the studies conducted on the vibration analysis of gossamer structures used inaccurate or approximate theories in modeling the internal pressure. The toroidal shaped structure is one of the important key element in space application, helps to support the reflector in space application. This paper discusses the finite-element analysis of an inflated torus. The eigen-frequencies are obtained via three-dimensional small-strain elasticity theory, based on extremum energy principle. The two finite-element model (model-1 and model-2) have cases have been generated using a commercial finite-element package. The structure model-1 with shell element and model-2 with the combination of the mass of enclosed fluid (air) added to the shell elements have been taken for the study. The model-1 is computed with present analytical approach to understand the convergence rate and the accuracy. The convergence study is made available for the symmetric modes and anti-symmetric modes about the centroidal-axis plane, meeting the eigen-frequencies of an inflatable torus with the circular cross section. The structural model-2 is introduced with air mass element and analyzed its eigen-frequency with different aspect ratio and mode shape response using in-plane and out-plane loading condition are studied.
Unresolved dielectronic satellites of the resonance line of heliumlike iron (Fe XXV)
International Nuclear Information System (INIS)
Bitter, M.; von Goeler, S.; Hill, K.W.; Horton, R.; Johnson, D.; Roney, W.; Sauthoff, N.; Silver, E.; Stodiek, W.
1981-02-01
(1s 2 nl - 1s2pnl, n greater than or equal to 3) dielectronic satellites of the resonance line of Fe XXV at 1.85 A have been observed from PLT (Princeton Large Torus) tokamak discharges and are used for a detailed comparison with theory. The necessary corrections for Doppler broadening measurements are discussed, and accurate satellite to resonance line ratios allowing for a determination of the total dielectronic recombination rate of Fe XXV are derived
International Nuclear Information System (INIS)
Jones, B.; Taylor, G.; Efthimion, P.C.; Munsat, T.
2004-01-01
Measurement of the magnetic field in a spherical torus by observation of harmonic overlap frequencies in the electron Bernstein wave (EBW) spectrum has been previously suggested [V.F. Shevchenko, Plasma Phys. Reports 26 (2000) 1000]. EBW mode conversion to X-mode radiation has been studied in the Current Drive Experiment-Upgrade spherical torus, [T. Jones, Ph.D. thesis, Princeton University, 1995] with emission measured at blackbody levels [B. Jones et al., Phys. Rev. Lett. 90 (2003) article no. 165001]. Sharp transitions in the thermally emitted EBW spectrum have been observed for the first two harmonic overlaps. These transition frequencies are determined by the magnetic field and electron density at the mode conversion layer in accordance with hot-plasma wave theory. Prospects of extending this measurement to higher harmonics, necessary in order to determine the magnetic field profile, and high beta equilibria are discussed for this proposed magnetic field diagnostic
The Geometry of the Semiclassical Wave Front Set for Schrödinger Eigenfunctions on the Torus
Energy Technology Data Exchange (ETDEWEB)
Cardin, Franco, E-mail: cardin@math.unipd.it; Zanelli, Lorenzo, E-mail: lzanelli@math.unipd.it [University of Padova, Department of Mathematics “Tullio Levi Civita” (Italy)
2017-06-15
This paper deals with the phase space analysis for a family of Schrödinger eigenfunctions ψ{sub ℏ} on the flat torus #Mathematical Double-Struck Capital T#{sup n} = (ℝ/2πℤ){sup n} by the semiclassical Wave Front Set. We study those ψ{sub ℏ} such that WF{sub ℏ}(ψ{sub ℏ}) is contained in the graph of the gradient of some viscosity solutions of the Hamilton-Jacobi equation. It turns out that the semiclassical Wave Front Set of such Schrödinger eigenfunctions is stable under viscous perturbations of Mean Field Game kind. These results provide a further viewpoint, and in a wider setting, of the link between the smooth invariant tori of Liouville integrable Hamiltonian systems and the semiclassical localization of Schrödinger eigenfunctions on the torus.
Baloković, M.; Brightman, M.; Harrison, F. A.; Comastri, A.; Ricci, C.; Buchner, J.; Gandhi, P.; Farrah, D.; Stern, D.
2018-02-01
The basic unified model of active galactic nuclei (AGNs) invokes an anisotropic obscuring structure, usually referred to as a torus, to explain AGN obscuration as an angle-dependent effect. We present a new grid of X-ray spectral templates based on radiative transfer calculations in neutral gas in an approximately toroidal geometry, appropriate for CCD-resolution X-ray spectra (FWHM ≥ 130 eV). Fitting the templates to broadband X-ray spectra of AGNs provides constraints on two important geometrical parameters of the gas distribution around the supermassive black hole: the average column density and the covering factor. Compared to the currently available spectral templates, our model is more flexible, and capable of providing constraints on the main torus parameters in a wider range of AGNs. We demonstrate the application of this model using hard X-ray spectra from NuSTAR (3–79 keV) for four AGNs covering a variety of classifications: 3C 390.3, NGC 2110, IC 5063, and NGC 7582. This small set of examples was chosen to illustrate the range of possible torus configurations, from disk-like to sphere-like geometries with column densities below, as well as above, the Compton-thick threshold. This diversity of torus properties challenges the simple assumption of a standard geometrically and optically thick toroidal structure commonly invoked in the basic form of the unified model of AGNs. Finding broad consistency between our constraints and those from infrared modeling, we discuss how the approach from the X-ray band complements similar measurements of AGN structures at other wavelengths.
International Nuclear Information System (INIS)
Synakowski, E.J.; Bell, M.G.; Bell, R.E.
2003-01-01
A major research goal of the national spherical torus experiment is establishing long-pulse, high beta, high confinement operation and its physics basis. This research has been enabled by facility capabilities developed during 2001 and 2002, including neutral beam (up to 7 MW) and high harmonic fast wave (HHFW) heating (up to 6 MW), toroidal fields up to 6 kG, plasma currents up to 1.5 MA, flexible shape control, and wall preparation techniques. These capabilities have enabled the generation of plasmas with β T ≡ /(B T0 2 /2μ 0 ) of up to 35%. Normalized beta values often exceed the no-wall limit, and studies suggest that passive wall mode stabilization enables this for H mode plasmas with broad pressure profiles. The viability of long, high bootstrap current fraction operations has been established for ELMing H mode plasmas with toroidal beta values in excess of 15% and sustained for several current relaxation times. Improvements in wall conditioning and fuelling are likely contributing to a reduction in H mode power thresholds. Electron thermal conduction is the dominant thermal loss channel in auxiliary heated plasmas examined thus far. HHFW effectively heats electrons, and its acceleration of fast beam ions has been observed. Evidence for HHFW current drive is obtained by comparison of the loop voltage evolution in plasmas with matched density and temperature profiles but varying phases of launched HHFW waves. Studies of emissions from electron Bernstein waves indicate a density scale length dependence of their transmission across the upper hybrid resonance near the plasma edge that is consistent with theoretical predictions. A peak heat flux to the divertor targets of 10 MW m -2 has been measured in the H mode, with large asymmetries being observed in the power deposition between the inner and outer strike points. Non-inductive plasma startup studies have focused on coaxial helicity injection. With this technique, toroidal currents up to 400 kA have been
About periodic and quasi-periodic orbits of a new type for twist maps of the torus
Directory of Open Access Journals (Sweden)
SALVADOR ADDAS-ZANATA
2002-03-01
Full Text Available We prove that for a large and important class of C¹ twist maps of the torus periodic and quasi-periodic orbits of a new type exist, provided that there are no rotational invariant circles (R.I.C's. These orbits have a non-zero "vertical rotation number'' (V.R.N., in contrast to what happens to Birkhoff periodic orbits and Aubry-Mather sets. The V.R.N. is rational for a periodic orbit and irrational for a quasi-periodic. We also prove that the existence of an orbit with a V.R.N = a > 0, implies the existence of orbits with V.R.N = b, for all 0 Provamos que para uma relevante classe de aplicações C¹ no toro, que desviam a vertical para a direita, existem órbitas periódicas e quase-periódicas de um novo tipo, se e somente se, não existem círculos rotacionais invariantes. Essas órbitas têm um número de rotação vertical não nulo (N.R.V, em contraste com o que ocorre para órbitas periódicas do tipo Birkhoff e para os conjuntos de Aubry-Mather. O número de rotação vertical é racional para uma órbita periódica e irracional para uma quase-periódica. Também provamos que a existência de uma órbita com N.R.V = a implica a existência de órbitas com N.R.V = b, para todo 0 < b < a. Como consequência destes resultados, obtemos que uma aplicação do toro que desvia a vertical e não possui círculos rotacionais invariates, necessariamente tem entropia topológica positiva, que é um resultado clássico. No fim deste trabalho apresentamos aplicações e exemplos, como o Standard map, dos resultados obtidos.
International Nuclear Information System (INIS)
Aslam, M.; Godden, W.G.; Scalise, D.T.
1978-08-01
This report presents an analytical and experimental investigation into the sloshing of water in torus tanks under horizontal earthquake ground motions. This study was motivated because of the use of torus tanks for pressure-suppression pools in Boiling Water Reactors. Such a pressure-suppression pool would typically have 80 ft and 140 ft inside and outside diameters, a 30 ft diameter section, and a water depth of 15 ft. A general finite element analysis was developed for all axisymmetric tanks and a computer program was written to obtain time-history plots of sloshing displacements of water and dynamic pressures. Tests were carried out on a 1/60th scale model under sinusoidal as well as simulated earthquake ground motions. Tests and analytical results regarding natural frequencies, surface water displacements, and dynamic pressures were compared and a good agreement was found within the range of displacements studied. The computer program gave satisfactory results within a maximum range of sloshing displacements in the full-size prototype of 30 in. which is greater than the value obtained under the full intensity of the El Centro earthquake (N-S component 1940). The range of linear behavior was studied experimentally by subjecting the torus model to increasing intensities of the El Centro earthquake
Control and data acquisition system for versatile experiment spherical torus at SNU
Energy Technology Data Exchange (ETDEWEB)
An, YoungHwa [Department of Nuclear Engineering, Seoul National University, Seoul 151-742 (Korea, Republic of); Chung, Kyoung-Jae, E-mail: jkjlsh1@snu.ac.kr [Department of Nuclear Engineering, Seoul National University, Seoul 151-742 (Korea, Republic of); Na, DongHyeon; Hwang, Y.S. [Department of Nuclear Engineering, Seoul National University, Seoul 151-742 (Korea, Republic of)
2013-10-15
A control and data acquisition system for VEST (Versatile Experiment Spherical Torus) at Seoul National University (SNU) has been developed to enable remote operation from a central control room. The control and data acquisition system consists of three subsystems; a main control and data acquisition system that triggers each device at the preprogrammed timing and collects various diagnostic signals during discharges, a monitoring system that watches and logs the device status continuously, and a data storage and distribution system that stores collected data and provides data access layer via Ethernet. The system is designed to be cost-effective, extensible and easy to develop by using well-established standard technologies and solutions. Combining broad accessibility with modern information technology, alarm signal can be sent immediately to the registered cell phones when the abnormal status of devices is found, and the web data distribution system enables data access from almost everywhere using smart phones or tablet computers. Since December 2011, VEST is operational and the control and data acquisition system has been successfully used for remote operation of VEST.
Sarasola, Xabier; Brenner, Paul; Hahn, Michael; Pedersen, Thomas
2009-11-01
The Columbia Non-neutral Torus (CNT) is the first stellarator devoted to the study of pure electron, partially neutralized and positron-electron plasmas. To date, CNT usually operates with electron rich plasmas (with negligible ion density) [1], but a stellarator can also confine plasmas of arbitrary degree of neutralization. In CNT the accumulation of ions alters the equilibrium of electron plasmas and a global instability has been observed when the ion fraction exceeds 10 %. A characterization of this instability is presented in [2], analyzing its parameter dependence and spatial structure (non- resonant with rational surfaces). A new set of experiments is currently underway studying plasmas of arbitrary degree of neutralization, ranging from pure electron to quasineutral plasmas. Basic observations show that the plasma potential decouples from emitter bias when we increase the degree of the neutralization of our plasmas. Partially neutralized plasmas are also characterized by multiple mode behavior with dominant modes between 20 and 200 kHz. When the plasma becomes quasineutral, it reverts to single mode behavior. The first results on partially neutralized plasmas confined on magnetic surfaces will be presented. [1] J. Kremer, PRL 97, (2006) 095003 [2] Q. Marksteiner, PRL 100 (2008) 065002
Confinement of pure electron plasmas in the Columbia Non-neutral Torus
International Nuclear Information System (INIS)
Berkery, John W.; Pedersen, Thomas Sunn; Kremer, Jason P.; Marksteiner, Quinn R.; Lefrancois, Remi G.; Hahn, Michael S.; Brenner, Paul W.
2007-01-01
The Columbia Non-neutral Torus (CNT) [T. S. Pedersen, J. P. Kremer, R. G. Lefrancois, Q. Marksteiner, N. Pomphrey, W. Reiersen, F. Dahlgreen, and X. Sarasola, Fusion Sci. Technol. 50, 372 (2006)] is a stellarator used to study non-neutral plasmas confined on magnetic surfaces. A detailed experimental study of confinement of pure electron plasmas in CNT is described here. Electrons are introduced into the magnetic surfaces by placing a biased thermionic emitter on the magnetic axis. As reported previously, the insulated rods holding this and other emitter filaments contribute to the radial transport by charging up negatively and creating ExB convective transport cells. A model for the rod-driven transport is presented and compared to the measured transport rates under a number of different conditions, finding good agreement. Neutrals also drive transport, and by varying the neutral pressure in the experiment, the effects of rod-driven and neutral-driven transport are separated. The neutral-driven electron loss rate scales linearly with neutral pressure. The neutral driven transport, presumably caused by electron-neutral collisions, is much greater than theoretical estimates for neoclassical diffusion in a classical stellarator with strong radial electric fields. In fact the confinement time is on the order of the electron-neutral collision time. Ion accumulation, electron attachment, and other effects are considered, but do not explain the observed transport rates
A megawatt-level 28 GHz heating system for the National Spherical Torus Experiment Upgrade
Directory of Open Access Journals (Sweden)
Taylor G.
2015-01-01
Full Text Available The National Spherical Torus Experiment Upgrade (NSTX-U will operate at axial toroidal fields of ≤ 1 T and plasma currents, Ip ≤ 2 MA. The development of non-inductive (NI plasmas is a major long-term research goal for NSTX-U. Time dependent numerical simulations of 28 GHz electron cyclotron (EC heating of low density NI start-up plasmas generated by Coaxial Helicity Injection (CHI in NSTX-U predict a significant and rapid increase of the central electron temperature (Te(0 before the plasma becomes overdense. The increased Te(0 will significantly reduce the Ip decay rate of CHI plasmas, allowing the coupling of fast wave heating and neutral beam injection. A megawatt-level, 28 GHz electron heating system is planned for heating NI start-up plasmas in NSTX-U. In addition to EC heating of CHI start-up discharges, this system will be used for electron Bernstein wave (EBW plasma start-up, and eventually for EBW heating and current drive during the Ip flattop.
Hybrid simulation of toroidal Alfvén eigenmode on the National Spherical Torus Experiment
Energy Technology Data Exchange (ETDEWEB)
Liu, D., E-mail: deyongl@uci.edu [Department of Physics and Astronomy, University of California, Irvine, California 92697 (United States); Fu, G. Y.; Podestà, M.; Breslau, J. A.; Fredrickson, E. D. [Princeton Plasma Physics Laboratory, Princeton, New Jersey 08543 (United States); Crocker, N. A.; Kubota, S. [Department of Physics and Astronomy, University of California, Los Angles, California 90095 (United States)
2015-04-15
Energetic particle modes and Alfvén eigenmodes driven by super-Alfvénic fast ions are routinely observed in neutral beam heated plasmas on the National Spherical Torus eXperiment (NSTX). These modes can significantly impact fast ion transport and thus cause fast ion redistribution or loss. Self-consistent linear simulations of Toroidal Alfvén Eigenmodes (TAEs) in NSTX plasmas have been carried out with the kinetic/magnetohydrodynamic hybrid code M3D-K using experimental plasma parameters and profiles including plasma toroidal rotation. The simulations show that unstable TAEs with n=3,4, or 5 can be excited by the fast ions from neutral beam injection. The simulated mode frequency, mode radial structure, and phase shift are consistent with measurements from a multi-channel microwave reflectometer diagnostic. A sensitivity study on plasma toroidal rotation, safety factor q profile, and initial fast ion distribution is performed. The simulations show that rotation can have a significant destabilizing effect when the rotation is comparable or larger than the experimental level. The mode growth rate is sensitive to q profile and fast ion distribution. Although mode structure and peak position depend somewhat on q profile and plasma rotation, the variation of synthetic reflectometer response is within experimental uncertainty and it is not sensitive enough to see the difference clearly.
International Nuclear Information System (INIS)
Stutman, D.; Finkenthal, M.; Tritz, K.; Redi, M. H.; Kaye, S. M.; Bell, M. G.; Bell, R. E.; LeBlanc, B. P.; Hill, K. W.; Medley, S. S.; Menard, J. E.; Rewoldt, G.; Wang, W. X.; Synakowski, E. J.; Levinton, F.; Kubota, S.; Bourdelle, C.; Dorland, W.; The NSTX Team
2006-01-01
Electron transport is rapid in most National Spherical Torus Experiment, M. Ono et al., Nucl. Fusion 40, 557 (2000) beam heated plasmas. A regime of improved electron confinement is nevertheless observed in low density L-mode (''low-confinement'') discharges heated by early beam injection. Experiments were performed in this regime to study the role of the current profile on thermal transport. Variations in the magnetic shear profile were produced by changing the current ramp rate and onset of neutral beam heating. An increased electron temperature gradient and local minimum in the electron thermal diffusivity were observed at early times in plasmas with the fastest current ramp and earliest beam injection. In addition, an increased ion temperature gradient associated with a region of reduced ion transport is observed at slightly larger radii. Ultrasoft x-ray measurements of double-tearing magnetohydrodynamic activity, together with current diffusion calculations, point to the existence of negative magnetic shear in the core of these plasmas. Discharges with slower current ramp and delayed beam onset, which are estimated to have more monotonic q-profiles, do not exhibit regions of reduced transport. The results are discussed in the light of the initial linear microstability assessment of these plasmas, which suggests that the growth rate of all instabilities, including microtearing modes, can be reduced by negative or low magnetic shear in the temperature gradient region. Several puzzles arising from the present experiments are also highlighted
Elmo Bumpy Torus proof of principle, Phase II: Title 1 report. Volume II. Toroidal vessel
International Nuclear Information System (INIS)
1982-01-01
The Toroidal Vessel provides the vacuum enclosure for containing the high temperature steady state plasma. In addition, the Toroidal Vessel must provide several viewing ports for plasma diagnostics, vacuum pumping ports for both high vacuum and roughing vacuum, feed-through ports for ECRH waveguides, limiter feed throughs for cooling and supporting the limiters, and ports for ion gages. The vessel must operate in an intense environment comprised of x-rays, microwaves, magnetic fields and plasma heat loads as well as the atmosphere pressure and gravity loads and the internal thermal stress loads due to heating and cooling of the torus. A key issue addressed was the choice of vacuum vessel seal and wall materials. In addition, during the course of the study, ORNL requested that horsecollar diagnostic ports be incorporated in the design. A comprehensive trade study was performed considering the vessel material issues in concert with the impact of the horsecollar port design. A change in baseline from an aluminum vessel with elastomer seals and circular diagnostic ports to austenitic stainless steel vessel with metal seals and horsecollar ports was agreed upon by both MDAC and ORNL towards the end of Title I
Radial transport in the Elmo Bumpy Torus in collisionless electron regimes
International Nuclear Information System (INIS)
Jaeger, E.F.; Hedrick, C.L.; Spong, D.A.
1979-01-01
One important area of disagreement between radial transport theory and the ELMO Bumpy Torus (EBT) experiment has been the degree of collisionality of the toroidal plasma electrons. Experiment shows relatively warm electrons (kTsub(e) approximately 300-600eV) and collisionless scaling, i.e. energy confinement increasing with temperature. But results of early one-dimensional (1-D), neoclassical transport models with radially inward pointing electric fields are limited to relatively cool electrons (kTsub(e) approximately 100-200eV) and collisional scaling. In this paper these early results are extended to include lowest-order effects of ion diffusion in regions where poloidal drift frequencies are small. The effects of direct, or non-diffusive, losses in such regions are neglected along with the effects of finite radial electric fields on electron transport coefficients and of self-consistent poloidal electric fields on ion transport coefficients. Results show that solutions in the collisionless electron regime do exist. Furthermore, when the effects of finite electron ring beta on magnetic fields near the plasma edge are included, these solutions occur at power levels consistent with experiment. (author)
Spectroscopic diagnostics for liquid lithium divertor studies on National Spherical Torus Experiment
International Nuclear Information System (INIS)
Soukhanovskii, V. A.; Roquemore, A. L.; Bell, R. E.; Kaita, R.; Kugel, H. W.
2010-01-01
The use of lithium-coated plasma facing components for plasma density control is studied in the National Spherical Torus Experiment (NSTX). A recently installed liquid lithium divertor (LLD) module has a porous molybdenum surface, separated by a stainless steel liner from a heated copper substrate. Lithium is deposited on the LLD from two evaporators. Two new spectroscopic diagnostics are installed to study the plasma surface interactions on the LLD: (1) A 20-element absolute extreme ultraviolet (AXUV) diode array with a 6 nm bandpass filter centered at 121.6 nm (the Lyman-α transition) for spatially resolved divertor recycling rate measurements in the highly reflective LLD environment, and (2) an ultraviolet-visible-near infrared R=0.67 m imaging Czerny-Turner spectrometer for spatially resolved divertor D I, Li I-II, C I-IV, Mo I, D 2 , LiD, CD emission and ion temperature on and around the LLD module. The use of photometrically calibrated measurements together with atomic physics factors enables studies of recycling and impurity particle fluxes as functions of LLD temperature, ion flux, and divertor geometry.
International Nuclear Information System (INIS)
Maqueda, R.J.; Stotler, D.P.
2010-01-01
While intermittent filamentary structures, also known as blobs, are routinely seen in the low-field-side scrape-off layer of the National Spherical Torus Experiment (NSTX) (Ono et al 2000 Nucl. Fusion 40 557), fine structured filaments are also seen on the lower divertor target plates of NSTX. These filaments, not associated with edge localized modes, correspond to the interaction of the turbulent blobs seen near the midplane with the divertor plasma facing components. The fluctuation level of the neutral lithium light observed at the divertor, and the skewness and kurtosis of its probability distribution function, is similar to that of midplane blobs seen in D α ; e.g. increasing with increasing radii outside the outer strike point (OSP) (separatrix). In addition, their toroidal and radial movement agrees with the typical movement of midplane blobs. Furthermore, with the appropriate magnetic topology, i.e. mapping between the portion of the target plates being observed into the field of view of the midplane gas puff imaging diagnostic, very good correlation is observed between the blobs and the divertor filaments. The correlation between divertor plate filaments and midplane blobs is lost close to the OSP. This latter observation is consistent with the existence of 'magnetic shear disconnection' due to the lower X-point, as proposed by Cohen and Ryutov (1997 Nucl. Fusion 37 621).
Experimental observations of MHD instabilities in the high-beta tokamak Torus-II
International Nuclear Information System (INIS)
Machida, M.
1982-01-01
The CO 2 laser scattering and interferometry diagnostics have been used to study the MHD instabilities in the high-beta tokamak Torus-II. Detailed measurements of the density and density fluctuation profiles have been performed. In order to measure density fluctuations with wavelengths longer than 2 cm, an interferometric like, phase matching technique has been developed. The toroidal and poloidal mode numbers have been measured using a double-beam, two-position technique. Working at high-beta values, average β greater than or equal to 10%, we have found parameters where the growing instabilities are created or suppressed. The plasma lifetime for both cases is seen to be about the same and the loss of the plasma appears to be caused by the decay in the external fields. The growing instability parameters are within the MHD regime, and it only grows at the outer edge of the plasma. This is in agreement with the theoretical Ballooning mode instability. The frequency and mode number measurements also agree with the Kinetic theory description of Ballooning modes. The comparison with possible other modes, such as Tearing and Drift instabilities, is performed and the Ballooning growth rate is shown to be the best fit to the experimental values
Energy Technology Data Exchange (ETDEWEB)
Lee, H.Y., E-mail: brbbebbero@snu.ac.kr [Seoul National University, Seoul (Korea, Republic of); Yang, J.; Kim, Y.G.; Yang, S.M.; Kim, Y.S.; Lee, K.H. [Seoul National University, Seoul (Korea, Republic of); An, Y.H. [National Fusion Research Institute, Daejon (Korea, Republic of); Chung, K.J.; Na, Y.S. [Seoul National University, Seoul (Korea, Republic of); Hwang, Y.S., E-mail: yhwang@snu.ac.kr [Seoul National University, Seoul (Korea, Republic of)
2016-11-01
Highlights: • The baking for partial wall heating and H{sub 2}/He GDC systems are developed in VEST. • The RGA and OES systems for monitoring impurities are constructed in VEST. • The partial baking and He GDC show limited effects on plasma characteristics. • H{sub 2} GDC above 4 h enables the longer plasma current duration up to ∼15 ms. • After H{sub 2} GDC, the discharge should be conducted within 3 h from treatment. - Abstract: Wall conditioning and impurity monitoring systems are developed in Versatile Experiment Spherical Torus (VEST). As a wall conditioning system, a baking system covering the vacuum vessel wall partially and a glow discharge cleaning (GDC) system using two electrodes with dc and 50 kHz power supplies are installed. The GDC system operates with hydrogen and helium gases for both chemical and physical desorption. The impurity monitoring system with residual gas analyzer (RGA), operating at <10{sup −5} Torr with a differential pumping system, is installed along with the optical emission spectroscopy (OES) system to monitor the hydrogen and impurity radiation lines. Effects of these wall conditioning techniques are investigated with the impurity monitoring system for ohmic discharges of VEST. The partial baking and He GDC show limited effects on plasma characteristics but sufficient H{sub 2} GDC above 4 h enables the longer plasma current duration up to ∼15 ms within 3 h from the end of treatment.
International Nuclear Information System (INIS)
Lee, H.Y.; Yang, J.; Kim, Y.G.; Yang, S.M.; Kim, Y.S.; Lee, K.H.; An, Y.H.; Chung, K.J.; Na, Y.S.; Hwang, Y.S.
2016-01-01
Highlights: • The baking for partial wall heating and H_2/He GDC systems are developed in VEST. • The RGA and OES systems for monitoring impurities are constructed in VEST. • The partial baking and He GDC show limited effects on plasma characteristics. • H_2 GDC above 4 h enables the longer plasma current duration up to ∼15 ms. • After H_2 GDC, the discharge should be conducted within 3 h from treatment. - Abstract: Wall conditioning and impurity monitoring systems are developed in Versatile Experiment Spherical Torus (VEST). As a wall conditioning system, a baking system covering the vacuum vessel wall partially and a glow discharge cleaning (GDC) system using two electrodes with dc and 50 kHz power supplies are installed. The GDC system operates with hydrogen and helium gases for both chemical and physical desorption. The impurity monitoring system with residual gas analyzer (RGA), operating at <10"−"5 Torr with a differential pumping system, is installed along with the optical emission spectroscopy (OES) system to monitor the hydrogen and impurity radiation lines. Effects of these wall conditioning techniques are investigated with the impurity monitoring system for ohmic discharges of VEST. The partial baking and He GDC show limited effects on plasma characteristics but sufficient H_2 GDC above 4 h enables the longer plasma current duration up to ∼15 ms within 3 h from the end of treatment.
Performance analyses of Elmo Bumpy Torus plasmas and plasma support systems
International Nuclear Information System (INIS)
Fenstermacher, M.E.
1979-01-01
The development and applcation of the OASIS Code (Operational Analysis of ELMO Bumpy Torus Support and Ignition Systems) for the study of EBT device and plasma performance are presented. The code performs a time-independent, zero-dimensional self-consistent calculation of plasma and plasmasupport systems parameters for the physics and engineering of EBT devices. The features of OASIS modeling for the EBT plasma include: (1) particle balance of the bulk toroidal and electron ring plasma components for experimental (H-H, D-D, He-He etc.) as well as reactor (D-T) devices; (2) energy balance in the bulk and ring plasmas for externally heated or ignition devices; (3) alpha particle effects for reactor devices; (4) auxiliary heating effects, including microwave (ECRH), RF heating (e.g., ICRH), and neutral beam methods; and (5) ignition conditions, including fusion power, alpha power and neutron wall loading. The performance studies using OASIS focussed on variation in plasma and device size and on microwave input power and frequency. An additional study was performed to determine the characteristics of an EBT reactor proof-of-principle device operated with a deuterium-tritium plasma. Sensitivity studies were performed for variation in the input microwave power sharing fractions and the dependence of the bulk n tau scaling law on bulk electron temperature
Status and Plans for the National Spherical Torus Experimental Research Facility
International Nuclear Information System (INIS)
Ono, M.; Bell, M.G.; Bell, R.E.; Bialek, J.M.; Bigelow, T.; Bitter, M.
2005-01-01
An overview of the research capabilities and the future plans on the MA-class National Spherical Torus Experiment (NSTX) at Princeton is presented. NSTX research is exploring the scientific benefits of modifying the field line structure from that in more conventional aspect ratio devices, such as the tokamak. The relevant scientific issues pursued on NSTX include energy confinement, MHD stability at high beta, non-inductive sustainment, solenoid-free start-up, and power and particle handling. In support of the NSTX research goal, research tools are being developed by the NSTX team. In the context of the fusion energy development path being formulated in the US, an ST-based Component Test Facility (CTF) and, ultimately a high beta Demo device based on the ST, are being considered. For these, it is essential to develop high performance (high beta and high confinement), steady-state (non-inductively driven) ST operational scenarios and an efficient solenoid-free start-up concept. We will also briefly describe the Next-Step-ST (NSST) device being designed to address these issues in fusion-relevant plasma conditions
The circular loxodromic lines of the torus – Brunelleschi's constructive principle?
Directory of Open Access Journals (Sweden)
Nevena Radojevic
2015-07-01
Full Text Available The umbrella vault of Pazzi Chapel in Santa Croce church in Florence has been the subject of many, 3d survey based researches, but it’s shape has never been described in satisfactory manner. The descriptions given so far, verified through three-dimensional models, despite whether drew near to geometry, did not give any explanation of building process, that as we know, often guides design choises and principles. In the current research, attempts are made to formulate new hypotheses on the logic and form-finding processes that could have determined the choosen shape of the sail. The existing technical literature and treatises on masonry do not give any information about the building processes in the sources, which is a core issue for explaining the peculiar shape of vaults. The analyses are done by correlating detailed surveys and geometric analyses of the vault, comprising the curves, surfaces and the possible masonry texture with the hypothesized form. The form of the inner sail is obtained by a three-dimensional transformation of a toric surface, with respect to the fixed point (dome’s oculus and constant lenght (torus radius, like the Nicomedes concoid in 2d. The vault is made by the inner sail (the concoid surface and the outer sail that is not visible in this moment (the hypothesized toric surface. In this research, and especially in the verification steps, we could recognize as very useful certain measures that, at first, seemed to have no meaning. The inner sail of the umbrella vault of the Pazzi Chapel is built on the basis of a regular dodecagon, with sides of about 4.90 Florentine braccia, while the diameter of the circumscribed circle is about 8.67 braccia, the measures that could seem a bit unusual for Brunelleschian architecture practice. Even the width of the ribs has a not expected measure of 0.38 braccia.When, on the other hand, we go on to describe the genesis of this sail (the inner sail, which is given by a three
Design of a repeating pneumatic pellet injector for the Joint European Torus
International Nuclear Information System (INIS)
Milora, S.L.; Combs, S.K.; Baylor, L.R.; Sparks, D.O.; Foust, C.R.; Gethers, F.E.
1987-01-01
A three-barrel pneumatic pellet injector has been developed for plasma fueling of the Joint European Torus (JET). The versatile device consists of three independent machine-gun-like mechanisms that operate at cryogenic temperatures (14 0 K to 20 0 K). Individual high speed extruders provide a continuous supply of solid deuterium to each gun assembly, where a reciprocating breech-side cutting mechanism forms and chambers cylindrical pellets from the extrusion; deuterium pellets are then accelerated in the gun barrels with controlled amounts of compressed hydrogen gas (pressures up to 100 bars) to velocities ≤ 1.5 km/s. The injector features three nominal pellet sizes (2.7 mm, 4.0 mm, and 6.0 mm) and has been tested at repetition rates of 5 Hz, 2.5 Hz, and 1 Hz, respectively. Each gun is capable of operating (individually or simultaneously) at the design repetition rate for 15-second duration pulses (limited only by the capacity of the extruder feed system). A remote, stand-alone control and data acquisition system is used for injector operation. 7 refs
International Nuclear Information System (INIS)
Combs, S.K.; Jernigan, T.C.; Baylor, L.R.; Milora, S.L.; Foust, C.R.; Kupschus, P.; Gadeberg, M.; Bailey, W.; Commission of the European Communities, Abingdon
1989-01-01
A pneumatic-based, hydrogen isotope pellet injector that was developed at the Oak Ridge National Laboratory for the plasma fueling application on the Joint European Torus (JET) was described at the last Symposium on Fusion Engineering (1987). The injector was installed on JET during 1987 and has since been used in plasma fueling experiments. The injector consists of three independent machine-gun-like mechanisms (nominal pellet sizes of 2.7, 4.0, and 6.0 mm in diameter), and it features repetitive operation (1-5 Hz) for quasi-steady-state conditions (>10 s). An extensive set of injector diagnostics permits evaluation of parameters for each pellet shot, including speed, mass, and integrity. Pellet speeds can be varied but typically range from 1.0 to 1.5 km/s. Over 5000 pellets have been fired with the equipment at JET, including about 2000 pellets shot for plasma fueling experiments. In recent experiments, the system performance has been outstanding, including excellent reproducibility in pellet speed and mass and a reliability of >98% in delivery of pellets to the plasma. 7 refs., 5 figs
Observations of toroidal and poloidal rotation in the high beta tokamak Torus II
International Nuclear Information System (INIS)
Kostek, C.A.
1983-01-01
The macroscopic rotation of plasma in a toroidal containment device is an important feature of the equilibrium. Toroidal and poloidal rotation in the high beta tokamak Torus II is measured experimentally by examining the Doppler shift of the 4685.75 A He II line emitted from the plasma. The toroidal flow at an average velocity of 1.6 x 10 6 cm/sec, a small fraction of the ion thermal speed, moves in the same direction as the toroidal plasma current. The poloidal flow follows the ion diamagnetic current direction, also at an average speed of 1.6 x 10 6 cm/sec. In view of certain ordering parameters, the toroidal flow is compared with predictions from neoclassical theory in the collosional, Pfirsch-Schluter regime. The poloidal motion, however results from an E x B drift in a positive radial electric field, approaching a stable ambipolar state. This radial electric field is determined from theory by using the measured poloidal velocity. Mechanisms for the time evolution of rotation are also examined. It appears that the circulation damping is governed by a global decay of the temperature and density gradients which, in turn, may be functions of radiative cooling, loss of equilibrium due to external field decay, or the emergence of a growing instability, occasionally observed in CO 2 interferometry measurements
Inertial fusion energy power plant design using the Compact Torus Accelerator: HYLIFE-CT
International Nuclear Information System (INIS)
Moir, R.W.; Hammer, J.H.; Hartman, C.W.; Leber, R.L.; Logan, B.G.; Petzoldt, R.W.; Tabak, M.; Tobin, M.T.; Bieri, R.L.; Hoffman, M.A.
1992-01-01
The Compact Torus Accelerator (CTA), under development at Lawrence Livermore National Laboratory, offers the promise of a low-cost, high-efficiency, high energy, high-power-density driver for ICF and MICF (Magnetically Insulated ICF) type fusion systems. A CTA with 100 MJ driver capacitor bank energy is predicted to deliver ∼30 MJ CT kinetic energy to a 1 cm 2 target in several nanoseconds for a power density of ∼10 16 watts/cm 2 . The estimated cost of delivered energy is ∼3$/Joule, or $100M for 30 MJ. This driver appears to be cost-effective and, in this regard, is virtually alone among IFE drivers. We discuss indirect-drive ICF with a DT fusion energy gain Q = 70 for a total yield of 2 GJ. The CT can be guided to the target inside a several-meter-long disposable cone made of frozen Li 2 BeF 4 , the same material as the coolant. We have designed a power plant including CT injection, target emplacement, containment, energy recovery, and tritium breeding. The cost of electricity is predicted to be 4.8 cents/kWh, which is competitive with future coal and nuclear costs
International Nuclear Information System (INIS)
Bell, R.E.; Andre, R.; Kaye, S.M.; Kolesnikov, R.A.; LeBlance, B.P.; Rewolldt, G.; Wang, W.X.; Sabbagh, S.A.
2010-01-01
Knowledge of poloidal velocity is necessary for the determination of the radial electric field, Er, which along with its gradient is linked to turbulence suppression and transport barrier formation. Recent measurements of poloidal flow on conventional tokamaks have been reported to be an order of magnitude larger than expected from neoclassical theory. In contrast, recent poloidal velocity measurements on the NSTX spherical torus (S. M. Kaye et al., Phys. Plasmas 8, 1977 (2001)) are near or below neoclassical estimates. A novel charge exchange recombination spectroscopy diagnostic is used, which features active and passive sets of up/down symmetric views to produce line-integrated poloidal velocity measurements that do not need atomic physics corrections. Local profiles are obtained with an inversion. Poloidal velocity measurements are compared with neoclassical values computed with the codes NCLASS (W. A. Houlberg et al., Phys. Plasmas 4, 3230 (1997)) and GTC-Neo (W. X. Wang, et al., Phys. Plasmas 13, 082501 (2006)), which has been updated to handle impurities.
Energy Technology Data Exchange (ETDEWEB)
Taylor, G.; Bertelli, N.; Ellis, R. A.; Gerhardt, S. P.; Hosea, J. C.; Poli, F. [Princeton Plasma Physics Laboratory, Princeton University, Princeton, New Jersey 08543 (United States); Harvey, R. W. [CompX, Del Mar, California 92014 (United States); Raman, R. [University of Washington, Seattle, Washington 98195 (United States); Smirnov, A. P. [M.V. Lomonosov Moscow State University, Moscow (Russian Federation)
2014-02-12
A megawatt-level, 28 GHz electron heating system is being designed to support non-inductive (NI) plasma current (I{sub p}) start-up and local heating and current drive (CD) in H-mode discharges in the National Spherical Torus Experiment Upgrade (NSTX-U). The development of fully NI I{sub p} start-up and ramp-up is an important goal of the NSTXU research program. 28 GHz electron cyclotron (EC) heating is predicted to rapidly increase the central electron temperature (T{sub e}(0)) of low density NI plasmas generated by Coaxial Helicity Injection (CHI). The increased T{sub e}(0) will significantly reduce the I{sub p} decay rate of CHI plasmas, allowing the coupling of fast wave heating and neutral beam injection. Also 28 GHz electron Bernstein wave (EBW) heating and CD can be used during the I{sub p} flat top in NSTX-U discharges when the plasma is overdense. Ray tracing and Fokker-Planck numerical simulation codes have been used to model EC and EBW heating and CD in NSTX-U. This paper presents a pre-conceptual design for the 28 GHz heating system and some of the results from the numerical simulations.
Critical Height of the Torus Instability in Two-ribbon Solar Flares
Energy Technology Data Exchange (ETDEWEB)
Wang, Dong; Liu, Rui; Wang, Yuming; Liu, Kai; Chen, Jun; Liu, Jiajia; Zhou, Zhenjun [CAS Key Laboratory of Geospace Environment, Department of Geophysics and Planetary Sciences, University of Science and Technology of China, Hefei, Anhui 230026 (China); Zhang, Min, E-mail: rliu@ustc.edu.cn [Department of Mathematics and Physics, Anhui Jianzhu University, Hefei 230601 (China)
2017-07-01
We studied the background field for 60 two-ribbon flares of M-and-above classes during 2011–2015. These flares are categorized into two groups, i.e., eruptive and confined flares, based on whether a flare is associated with a coronal mass ejection or not. The background field of source active regions is approximated by a potential field extrapolated from the B {sub z} component of vector magnetograms provided by the Helioseismic and Magnetic Imager. We calculated the decay index n of the background field above the flaring polarity inversion line, and defined a critical height h {sub crit} corresponding to the theoretical threshold ( n {sub crit} = 1.5) of the torus instability. We found that h {sub crit} is approximately half of the distance between the centroids of opposite polarities in active regions and that the distribution of h {sub crit} is bimodal: it is significantly higher for confined flares than for eruptive ones. The decay index increases monotonously with increasing height for 86% (84%) of the eruptive (confined) flares but displays a saddle-like profile for the rest, 14% (16%), which are found exclusively in active regions of multipolar field configuration. Moreover, n at the saddle bottom is significantly smaller in confined flares than that in eruptive ones. These results highlight the critical role of background field in regulating the eruptive behavior of two-ribbon flares.
Control and data acquisition system for versatile experiment spherical torus at SNU
International Nuclear Information System (INIS)
An, YoungHwa; Chung, Kyoung-Jae; Na, DongHyeon; Hwang, Y.S.
2013-01-01
A control and data acquisition system for VEST (Versatile Experiment Spherical Torus) at Seoul National University (SNU) has been developed to enable remote operation from a central control room. The control and data acquisition system consists of three subsystems; a main control and data acquisition system that triggers each device at the preprogrammed timing and collects various diagnostic signals during discharges, a monitoring system that watches and logs the device status continuously, and a data storage and distribution system that stores collected data and provides data access layer via Ethernet. The system is designed to be cost-effective, extensible and easy to develop by using well-established standard technologies and solutions. Combining broad accessibility with modern information technology, alarm signal can be sent immediately to the registered cell phones when the abnormal status of devices is found, and the web data distribution system enables data access from almost everywhere using smart phones or tablet computers. Since December 2011, VEST is operational and the control and data acquisition system has been successfully used for remote operation of VEST
A high time resolution x-ray diagnostic on the Madison Symmetric Torus
DuBois, Ami M.; Lee, John David; Almagri, Abdulgadar F.
2015-07-01
A new high time resolution x-ray detector has been installed on the Madison Symmetric Torus (MST) to make measurements around sawtooth events. The detector system is comprised of a silicon avalanche photodiode, a 20 ns Gaussian shaping amplifier, and a 500 MHz digitizer with 14-bit sampling resolution. The fast shaping time diminishes the need to restrict the amount of x-ray flux reaching the detector, limiting the system dead-time. With a much higher time resolution than systems currently in use in high temperature plasma physics experiments, this new detector has the versatility to be used in a variety of discharges with varying flux and the ability to study dynamics on both slow and fast time scales. This paper discusses the new fast x-ray detector recently installed on MST and the improved time resolution capabilities compared to the existing soft and hard x-ray diagnostics. In addition to the detector hardware, improvements to the detector calibration and x-ray pulse identification software, such as additional fitting parameters and a more sophisticated fitting routine are discussed. Finally, initial data taken in both high confinement and standard reversed-field pinch plasma discharges are compared.
International Nuclear Information System (INIS)
Fredrickson, E.D.; Gorelenkov, E.D.; Cheng, C.Z.; Bell, R.; Darrow, D.; Johnson, D.; Kaye, S.; LeBlanc, B.; Menard, J.; Kubota, S.; Peebles, W.
2001-01-01
With the first injection of neutral beams on the National Spherical Torus Experiment (NSTX), a broad and complicated spectrum of coherent modes was seen between approximately 0.4 MHz and 2.5 MHz [where f(subscript ''ci'')] for deuterium is approximately 2.2 MHz. The modes have been observed with high bandwidth magnetic pick-up coils and with a reflectometer. The parametric scaling of the mode frequency with density and magnetic field is consistent with Alfvenic modes (linear in B, inversely with the square root of density). These modes have been identified as magnetosonic waves or compressional Alfven eigenmodes (CAE) excited by a cyclotron resonance with the neutral-beam ions. Modes have also been observed in the frequency range 50-150 kHz with toroidal mode numbers n = 1-5. These lower frequency modes are thought to be related to the TAE [Toroidal Alfven Eigenmode] seen commonly in tokamaks and driven by energetic fast ion populations resulting from ICRF [ion cyclotron range of frequency] and NBI [neutral-beam injection] heating. There is no clear indication of enhanced fast ion losses associated with the modes
International Nuclear Information System (INIS)
Izzo, V.A.; Jarboe, T.R.
2005-01-01
The Helicity Injected Torus with Steady Inductive drive (HIT-SI) [P. E. Sieck, W. T. Hamp, V. A. Izzo, T. R. Jarboe, B. A. Nelson, R. G. O'Neill, A. J. Redd, and R. J. Smith, IEEE Conference Record-Abstracts. 31st IEEE International Conference On Plasma Science (IEEE Catalog No. 04CH37537), 2004, p. 160] is a spheromak driven by steady inductive helicity injection (SIHI) and consists of the toroidally symmetric spheromak confinement region and two nonsymmetric helicity injectors. The three-dimensional (3D) magnetohydrodynamic code NIMROD [A. H. Glasser, C. R. Sovinec, R. A. Nebel, T. A. Gianakon, S. J. Plimpton, M. S. Chu, and D. D. Schnack, Plasma Phys. Controlled Fusion, 41, A747 (1999)] is used to simulate HIT-SI operation, but the code's toroidally symmetric boundary requires a creative treatment of the injectors. Sustained HIT-SI operation is simulated with nonaxisymmetric boundary conditions. In driven simulations at low Lundquist number S no n=0 fields are generated as a result of relaxation of the predominantly n=1 injector fields until the injectors are quickly shut off. At S=500, an n=0 component arises due to relaxation during sustainment. As S is increased further, the ratio of n=0 (equilibrium) fields to n=1 (injector) fields increases. The effects of a thin insulating boundary layer on the plasma decay time are also discussed
Design considerations for the TF center conductor post for the Ignition Spherical Torus (IST)
International Nuclear Information System (INIS)
Dalton, G.R.; Haines, J.R.
1986-01-01
A trade-off study has been carried out to compare the differential costs of using high-strength alloy copper versus oxygen-free, high-conductivity (OFHC) copper for the center legs of the toroidal field (TF) coils of an Ignition Spherical Torus (IST). The electrical heating, temperatures, stresses, cooling requirements, material costs, pump costs, and power to drive the TF coils and pumps are all assessed for both materials for a range of compact tokamak reactors. The alloy copper material is found to result in a more compact reactor and to allow use of current densities of up to 170 MA/m 2 versus 40 MA/m 2 for the OFHC copper. The OFHC conductor system with high current density is $24 million less expensive than more conventional copper systems with 30 MA/m 2 . The alloy copper system costs $32 million less than conventional systems. Therefore, the alloy system offers a net savings of $8 million compared to the 50% cold-worked OFHC copper system. Although the savings are a significant fraction of the center conductor post cost, they are relatively insignificant in terms of the total device cost. It is concluded that the use of alloy copper contributes very little to the economic or technical viability of the compact IST. It is recommended that a similar systematic approach be applied to evaluating coil material and current density trade-offs for other compact copper-TF-coil tokamak designs. 9 refs., 13 figs., 13 tabs
Design of a repeating pneumatic pellet injector for the Joint European Torus
International Nuclear Information System (INIS)
Milora, S.L.; Combs, S.K.; Baylor, L.R.; Foust, C.R.; Gethers, F.E.; Sparks, D.O.
1987-01-01
A three-barrel pneumatic pellet launcher developed at Oak Ridge National Laboratory (ORNL) serves as the principal component of a plasma fueling system for the Joint European Torus (JET). The versatile device consists of three independent machine gun-like mechanisms that operate at cryogenic temperatures (14-20K). Individual high-speed extruders provide a continuous supply of solid deuterium to each gun assembly, where a reciprocating breech-side cutting mechanism forms and chambers cylindrical pellets from the extrusion; the deuterium pellets are then accelerated in the gun barrels with controlled amounts of compressed hydrogen gas (pressures up to 100 bar) to velocities of ≤1.5 km/s. The injector features three nominal pellet sizes (2.7,4.0, and 6.0 mm) and has been tested at pellet repetition rates of 5,2.5, and 1 Hz, respectively. Each gun can operate (individually or simultaneously) at the design repetition rate for 15-s pulses (limited only by the capacity of the extruder feed system). A remote, stand-alone control and data acquisition system is used for injector operation
Effect of electric fields and fluctuations on confinement in a bumpy torus
International Nuclear Information System (INIS)
Hiroe, S.; Glowienka, J.C.; Hillis, D.L.
1986-06-01
In order to understand the relationships between confinement and space potential (electric field) and between confinement and density fluctuations, plasma parameters in the ELMO Bumpy Torus Scale (EBT-S) have been measured systematically for a wide range of operating conditions. Present EBT plasma parameters do not show a strong dependence on the potential profile, but rather exhibit a correlation with the fluctuations. The plasma pressure profile is found to be consistent with the profile anticipated on the basis of the flute stability criterion for a marginally stable plasma. For a heating power of 100 kW, the stored energy density is found to be restricted to the range between 4.5 x 10 13 eV-cm -3 and 7 x 10 13 eV-cm -3 . The lower limit remains constant regardless of heating power and pertains to plasmas lacking an equilibrium and/or stability. The upper limit increases with heating power and is found to result from the onset of instabilities. In between the two limits is a plasma that is in an equilibrium state and is marginally stable. Operational trajectories exist that take the EBT plasma from one limit to the other
International Nuclear Information System (INIS)
Gerhardt, S.P.; Menard, J.E.
2008-01-01
A detailed analysis of the plasma current quench in the National Spherical Torus Experiment (M.Ono, et al Nuclear Fusion 40, 557 (2000)) is presented. The fastest current quenches are fit better by a linear waveform than an exponential one. Area-normalized current quench times down to .4 msec/m2 have been observed, compared to the minimum of 1.7 msec/m2 recommendation based on conventional aspect ratio tokamaks; as noted in previous ITPA studies, the difference can be explained by the reduced self-inductance at low aspect ratio and high-elongation. The maximum instantaneous dIp/dt is often many times larger than the mean quench rate, and the plasma current before the disruption is often substantially less than the flat-top value. The poloidal field time-derivative during the disruption, which is directly responsible for driving eddy currents, has been recorded at various locations around the vessel. The Ip quench rate, plasma motion, and magnetic geometry all play important roles in determining the rate of poloidal field change
Research program for plasma confinement and heating in ELMO bumpy torus devices
International Nuclear Information System (INIS)
Dandl, R.A.; Dory, R.A.; Eason, H.O.
1975-06-01
A sequence of experimental devices and related research activities which leads progressively toward an attractive full-scale reactor is described. The implementation of the steps in this sequence hinges on the development of microwave power sources, with high specific power levels, at millimeter wavelengths. Two proposed steps in this sequence are described. The first step proposed here, denoted EBT-S, requires increasing the EBT magnetic field to permit microwave heating at 18 and 28 GHz, as compared to the present 10.6 and 18-GHz configuration. A three-fold increase in plasma density, some increase in the temperatures, and an opportunity to test the validity of the transport models presently used to predict the plasma parameters are anticipated. This step will provide important operating experience with the 28-GHz power supplies, which are prototype tubes for millimeter sources at 120 GHz In the second step a new superconducting bumpy torus, EBT-II, would be fabricated to permit microwave heating at 90 and 120 GHz. This device would be designed to produce plasma densities and temperatures comparable to those of present-day tokamaks. This report reviews the experimental and theoretical research on EBT that has been carried out to date or formulated for the near future, and provides a status report as well as a research program plan. (U.S.)
National Spherical Torus Experiment (NSTX) Engineering Overview and Research Results 1999 - 2000
International Nuclear Information System (INIS)
Neumeyer, C.
2000-01-01
The NSTX is a new US facility for the study of plasma confinement, heating, and current drive in a low aspect ratio, spherical torus (ST) configuration. The ST configuration is an alternate magnetic confinement concept which is characterized by high beta (ratio plasma pressure to magnetic field pressure) and low toroidal field compared to conventional tokamaks, and could provide a pathway to the realization of a practical fusion power source. NSTX achieved first plasma in February 1999, and since that time has completed and commissioned all components and systems within the machine proper. Routine operation with inductively driven plasma current less than or equal to 1MA and flat top less than or equal to 0.3 seconds has been established, and the ohmic characterization phase of the research program is underway. Radio Frequency (RF) and Neutral Beam Injection (NBI) systems have been installed and are presently being commissioned. This paper describes the NSTX mission, gives an overview of the engineering design, and summarizes the research results obtained thus far
Status and plans for the national spherical torus experimental research facility
International Nuclear Information System (INIS)
Ono, Masayuki; Bell, M.G.; Bell, R.E.
2005-01-01
An overview of the research capabilities and the future plans on the MA-class National Spherical Torus Experiment (NSTX) at Princeton is presented. NSTX research is exploring the scientific benefits of modifying the field line structure from that in more conventional aspect ratio devices, such as the tokamak. The relevant scientific issues pursued on NSTX include energy confinement, MHD stability at high β, non-inductive sustainment, solenoid-free start-up, and power and particle handling. In support of the NSTX research goal, research tools are being developed by the NSTX team. In the context of the fusion energy development path being formulated in the US, an ST-based Component Test Facility (CTF) and, ultimately a high β Demo device based on the ST, are being considered. For these, it is essential to develop high performance (high β and high confinement), steady-state (non-inductively driven) ST operational scenarios and an efficient solenoid-free start-up concept. We will also briefly describe the Next-Step-ST (NSST) device being designed to address these issues in fusion-relevant plasma conditions. (author)
Liquid-metal plasma-facing component research on the National Spherical Torus Experiment
International Nuclear Information System (INIS)
Jaworski, M A; Khodak, A; Kaita, R
2013-01-01
Liquid metal plasma-facing components (PFCs) have been proposed as a means of solving several problems facing the creation of economically viable fusion power reactors. Liquid metals face critical issues in three key areas: free-surface stability, material migration and demonstration of integrated scenarios. To date, few demonstrations exist of this approach in a diverted tokamak and we here provide an overview of such work on the National Spherical Torus Experiment (NSTX). The liquid lithium divertor (LLD) was installed and operated for the 2010 run campaign using evaporated coatings as the filling method. Despite a nominal liquid level exceeding the capillary structure and peak current densities into the PFCs exceeding 100 kA m −2 , no macroscopic ejection events were observed. The stability can be understood from a Rayleigh–Taylor instability analysis. Capillary restraint and thermal-hydraulic considerations lead to a proposed liquid-metal PFCs scheme of actively-supplied, capillary-restrained systems. Even with state-of-the-art cooling techniques, design studies indicate that the surface temperature with divertor-relevant heat fluxes will still reach temperatures above 700 °C. At this point, one would expect significant vapor production from a liquid leading to a continuously vapor-shielded regime. Such high-temperature liquid lithium PFCs may be possible on the basis of momentum-balance arguments. (paper)
Liquid-metal plasma-facing component research on the National Spherical Torus Experiment
Jaworski, M. A.; Khodak, A.; Kaita, R.
2013-12-01
Liquid metal plasma-facing components (PFCs) have been proposed as a means of solving several problems facing the creation of economically viable fusion power reactors. Liquid metals face critical issues in three key areas: free-surface stability, material migration and demonstration of integrated scenarios. To date, few demonstrations exist of this approach in a diverted tokamak and we here provide an overview of such work on the National Spherical Torus Experiment (NSTX). The liquid lithium divertor (LLD) was installed and operated for the 2010 run campaign using evaporated coatings as the filling method. Despite a nominal liquid level exceeding the capillary structure and peak current densities into the PFCs exceeding 100 kA m-2, no macroscopic ejection events were observed. The stability can be understood from a Rayleigh-Taylor instability analysis. Capillary restraint and thermal-hydraulic considerations lead to a proposed liquid-metal PFCs scheme of actively-supplied, capillary-restrained systems. Even with state-of-the-art cooling techniques, design studies indicate that the surface temperature with divertor-relevant heat fluxes will still reach temperatures above 700 °C. At this point, one would expect significant vapor production from a liquid leading to a continuously vapor-shielded regime. Such high-temperature liquid lithium PFCs may be possible on the basis of momentum-balance arguments.
Exposición espontánea de un torus palatino de la línea media
Directory of Open Access Journals (Sweden)
Gustavo Sinisterra
2013-03-01
Full Text Available Introducción. El torus, o rodete, palatino es una alteración ósea benigna que puede generar molestias en la fonación y en la deglución. Cuando su crecimiento o exposición persistente producen síntomas molestos, debe ser resecado quirúrgicamente. Presentación del caso. Se trata de una paciente de 82 años de edad, que consultó por una lesión ulcerativa de un año de evolución, que producía dolor, halitosis y molestia a la deglución. En el examen físico de la cavidad oral, se observó una prominencia de consistencia dura en la línea media, con perforación y ulceración de la mucosa palatina en su porción lateral posterior izquierda. Se consideraron los diagnósticos de torus palatino, osteoma, granuloma piógeno y neoplasia de tejidos blandos. Se decidió resecarla quirúrgicamente y hacer el estudio histopatológico. La evolución clínica fue satisfactoria, con resolución completa un mes después de la cirugía. En el estudio de histopatología se observó hiperostosis ósea con inflamación crónica de los tejidos blandos e hiperplasia simple de la mucosa, que corresponden a un torus palatino. Discusión. Se reporta un inusual caso de exposición espontánea de un torus palatino que ocupaba casi toda la bóveda palatina, se describe su resección quirúrgica y se informan los hallazgos de histopatología. En la revisión bibliográfica realizada, no se encontró un reporte previo de exposición espontánea de torus palatino. doi: http://dx.doi.org/10.7705/biomedica.v33i1.1480
International Nuclear Information System (INIS)
Fredrickson, E. D.; Belova, E. V.; Battaglia, D. J.
2017-01-01
In this paper we present data from experiments on the National Spherical Torus Experiment Upgrade, where it is shown for the first time that small amounts of high pitch-angle beam ions can strongly suppress the counterpropagating global Alfven eigenmodes (GAE). GAE have been implicated in the redistribution of fast ions and modification of the electron power balance in previous experiments on NSTX. The ability to predict the stability of Alfven modes, and developing methods to control them, is important for fusion reactors like the International Tokamak Experimental Reactor, which are heated by a large population of nonthermal, super-Alfvenic ions consisting of fusion generated alpha's and beam ions injected for current profile control. We present a qualitative interpretation of these observations using an analytic model of the Doppler-shifted ion-cyclotron resonance drive responsible for GAE instability which has an important dependence on k(perpendicular to rho L). A quantitative analysis of this data with the HYM stability code predicts both the frequencies and instability of the GAE prior to, and suppression of the GAE after the injection of high pitch-angle beam ions.
International Nuclear Information System (INIS)
Mastrovito, Dana M.
2002-01-01
Data acquisition on the National Spherical Torus Experiment at the Princeton Plasma Physics Laboratory (PPPL) has increasingly involved the use of Personal Computers and specially developed 'turn-key' hardware and software systems to control diagnostics. Interaction with these proprietary software packages is accomplished through use of Visual Basic, or Visual C++ and Component Object Model (COM) technology. COM is a software architecture that allows the components made by different software vendors to be combined into a variety of applications. This technology is particularly well suited to these systems because of its programming language independence, standards for function calling between components, and ability to transparently reference remote processes. COM objects make possible the creation of acquisition software that can control the experimental parameters of both the hardware and software. Synchronization of these applications for diagnostics, such as charged couple device cameras and residual gas analyzers, with the rest of the experiment event cycle at PPPL has been made possible by utilization of the MDSplus libraries for Windows. Instead of transferring large data files to remote disk space, Windows MDSplus events and I/O functions allow us to put raw data into MDSplus directly from interactive data language for Windows and Visual Basic. The combination of COM technology and the MDSplus libraries for Windows provide the tools for many new possibilities in versatile acquisition applications and future diagnostics
Energy Technology Data Exchange (ETDEWEB)
Durance, G
1985-08-01
A Compact Torus (CT) is a low-aspect-ratio, axisymmetric, closed-magnetic-field-line configuration with no vessel wall or magnetic field coils linking the hole in the plasma toroid. The potential reactor advantages include high beta, simple geometry, high power density, and translation of the toroid. FRC (Field Reversed Configuration) have negligible toroidal magnetic fields; equilibria tend to be elongated. Gross stability is observed for several Alfven times, but transport mechanisms and confinement time scaling are poorly understood. Translation experiments are expanding the accessable parameter space. Spheromaks have comparable toroidal and poloidal fields. The configuration is related to the RFP although the toroidal field is generated by internal plasma currents. Detached mode (plasma and gun or flux core not connected) and linked mode have been studied. Rotamaks use a rotating magnetic field to maintain the plasma toroidal current; the drive mechanism is analagous to an induction motor. There has been no evidence for gross instabilities although temperatures are low. Particle rings generate CT with particle gyroradii comparable to plasma dimensions. The large orbits may aid in gross MHD stability.
International Nuclear Information System (INIS)
Dana M. Mastrovito
2002-01-01
Data acquisition on the National Spherical Torus Experiment (NSTX) at the Princeton Plasma Physics Laboratory (PPPL) has increasingly involved the use of Personal Computers (PC's) and specially developed ''turn-key'' hardware and software systems to control diagnostics. Interaction with these proprietary software packages is accomplished through use of Visual Basic, or Visual C++ and COM (Component Object Model) technology. COM is a software architecture that allows the components made by different software vendors to be combined into a variety of applications. This technology is particularly well suited to these systems because of its programming language independence, standards for function calling between components, and ability to transparently reference remote processes. COM objects make possible the creation of acquisition software that can control the experimental parameters of both the hardware and software. Synchronization of these applications for diagnostics, such as CCD camer as and residual gas analyzers, with the rest of the experiment event cycle at PPPL has been made possible by utilization of the MDSplus libraries for Windows. Instead of transferring large data files to remote disk space, Windows MDSplus events and I/O functions allow us to put raw data into MDSplus directly from IDL for Windows and Visual Basic. The combination of COM technology and the MDSplus libraries for Windows provide the tools for many new possibilities in versatile acquisition applications and future diagnostics
International Nuclear Information System (INIS)
Dana M. Mastrovito
2002-03-01
Data acquisition on the National Spherical Torus Experiment (NSTX) at the Princeton Plasma Physics Laboratory (PPPL) has increasingly involved the use of Personal Computers (PC's) and specially developed ''turn-key'' hardware and software systems to control diagnostics. Interaction with these proprietary software packages is accomplished through use of Visual Basic, or Visual C++ and COM (Component Object Model) technology. COM is a software architecture that allows the components made by different software vendors to be combined into a variety of applications. This technology is particularly well suited to these systems because of its programming language independence, standards for function calling between components, and ability to transparently reference remote processes. COM objects make possible the creation of acquisition software that can control the experimental parameters of both the hardware and software. Synchronization of these applications for diagnostics, such as CCD camer as and residual gas analyzers, with the rest of the experiment event cycle at PPPL has been made possible by utilization of the MDSplus libraries for Windows. Instead of transferring large data files to remote disk space, Windows MDSplus events and I/O functions allow us to put raw data into MDSplus directly from IDL for Windows and Visual Basic. The combination of COM technology and the MDSplus libraries for Windows provide the tools for many new possibilities in versatile acquisition applications and future diagnostics
Electron Bernstein wave emission based diagnostic on National Spherical Torus Experiment (invited)
International Nuclear Information System (INIS)
Diem, S.; Taylor, G.; Caughman, John B.; Efthimion, P.C.; Kugel, H.; LeBlanc, B.; Preinhaelter, J.; Sabbagh, S.A.; Urban, J.
2008-01-01
National Spherical Torus Experiment (NSTX) is a spherical tokamak (ST) that operates with n(e) up to 10(20) m(-3) and B-T less than 0.6 T, cutting off low harmonic electron cyclotron (EC) emission widely used for T-e measurements on conventional aspect ratio tokamaks. The electron Bernstein wave (EBW) can propagate in ST plasmas and is emitted at EC harmonics. These properties suggest thermal EBW emission (EBE) may be used for local T-e measurements in the ST. Practically, a robust T-e(R,t) EBE diagnostic requires EBW transmission efficiencies of >90% for a wide range of plasma conditions. EBW emission and coupling physics were studied on NSTX with an obliquely viewing EBW to O-mode (B-X-O) diagnostic with two remotely steered antennas, coupled to absolutely calibrated radiometers. While T-e(R,t) measurements with EBW emission on NSTX were possible, they were challenged by several issues. Rapid fluctuations in edge n(e) scale length resulted in >20% changes in the low harmonic B-X-O transmission efficiency. Also, B-X-O transmission efficiency during H modes was observed to decay by a factor of 5-10 to less than a few percent. The B-X-O transmission behavior during H modes was reproduced by EBE simulations that predict that EBW collisional damping can significantly reduce emission when T-e < 30 eV inside the B-X-O mode conversion (MC) layer. Initial edge lithium conditioning experiments during H modes have shown that evaporated lithium can increase T-e inside the B-X-O MC layer, significantly increasing B-X-O transmission.
Electron Bernstein Wave Emission Based Diagnostic on National Spherical Torus Experiment
International Nuclear Information System (INIS)
Diem, S.; Taylor, G.; Caughman, John B.; Efthimion, P.C.; Kugel, H.; LeBlanc, B.; Preinhaelter, J.; Sabbagh, S.A.; Urban, J.; Wilgen, John B.
2008-01-01
National Spherical Torus Experiment (NSTX) is a spherical tokamak (ST) that operates with n(e) up to 10(20) m(-3) and B(T) less than 0.6 T, cutting off low harmonic electron cyclotron (EC) emission widely used for T(e) measurements on conventional aspect ratio tokamaks. The electron Bernstein wave (EBW) can propagate in ST plasmas and is emitted at EC harmonics. These properties suggest thermal EBW emission (EBE) may be used for local T(e) measurements in the ST. Practically, a robust T(e)(R,t) EBE diagnostic requires EBW transmission efficiencies of >90% for a wide range of plasma conditions. EBW emission and coupling physics were studied on NSTX with an obliquely viewing EBW to O-mode (B-X-O) diagnostic with two remotely steered antennas, coupled to absolutely calibrated radiometers. While T(e)(R,t) measurements with EBW emission on NSTX were possible, they were challenged by several issues. Rapid fluctuations in edge n(e) scale length resulted in >20% changes in the low harmonic B-X-O transmission efficiency. Also, B-X-O transmission efficiency during H modes was observed to decay by a factor of 5-10 to less than a few percent. The B-X-O transmission behavior during H modes was reproduced by EBE simulations that predict that EBW collisional damping can significantly reduce emission when T(e)< 30 eV inside the B-X-O mode conversion (MC) layer. Initial edge lithium conditioning experiments during H modes have shown that evaporated lithium can increase T(e) inside the B-X-O MC layer, significantly increasing B-X-O transmission.
APEnet+: a 3D Torus network optimized for GPU-based HPC Systems
International Nuclear Information System (INIS)
Ammendola, R; Biagioni, A; Frezza, O; Lo Cicero, F; Lonardo, A; Paolucci, P S; Rossetti, D; Simula, F; Tosoratto, L; Vicini, P
2012-01-01
In the supercomputing arena, the strong rise of GPU-accelerated clusters is a matter of fact. Within INFN, we proposed an initiative — the QUonG project — whose aim is to deploy a high performance computing system dedicated to scientific computations leveraging on commodity multi-core processors coupled with latest generation GPUs. The inter-node interconnection system is based on a point-to-point, high performance, low latency 3D torus network which is built in the framework of the APEnet+ project. It takes the form of an FPGA-based PCIe network card exposing six full bidirectional links running at 34 Gbps each that implements the RDMA protocol. In order to enable significant access latency reduction for inter-node data transfer, a direct network-to-GPU interface was built. The specialized hardware blocks, integrated in the APEnet+ board, provide support for GPU-initiated communications using the so called PCIe peer-to-peer (P2P) transactions. This development is made in close collaboration with the GPU vendor NVIDIA. The final shape of a complete QUonG deployment is an assembly of standard 42U racks, each one capable of 80 TFLOPS/rack of peak performance, at a cost of 5 k€/T F LOPS and for an estimated power consumption of 25 kW/rack. In this paper we report on the status of final rack deployment and on the R and D activities for 2012 that will focus on performance enhancement of the APEnet+ hardware through the adoption of new generation 28 nm FPGAs allowing the implementation of PCIe Gen3 host interface and the addition of new fault tolerance-oriented capabilities.
APEnet+: a 3D Torus network optimized for GPU-based HPC Systems
Energy Technology Data Exchange (ETDEWEB)
Ammendola, R [INFN Tor Vergata (Italy); Biagioni, A; Frezza, O; Lo Cicero, F; Lonardo, A; Paolucci, P S; Rossetti, D; Simula, F; Tosoratto, L; Vicini, P [INFN Roma (Italy)
2012-12-13
In the supercomputing arena, the strong rise of GPU-accelerated clusters is a matter of fact. Within INFN, we proposed an initiative - the QUonG project - whose aim is to deploy a high performance computing system dedicated to scientific computations leveraging on commodity multi-core processors coupled with latest generation GPUs. The inter-node interconnection system is based on a point-to-point, high performance, low latency 3D torus network which is built in the framework of the APEnet+ project. It takes the form of an FPGA-based PCIe network card exposing six full bidirectional links running at 34 Gbps each that implements the RDMA protocol. In order to enable significant access latency reduction for inter-node data transfer, a direct network-to-GPU interface was built. The specialized hardware blocks, integrated in the APEnet+ board, provide support for GPU-initiated communications using the so called PCIe peer-to-peer (P2P) transactions. This development is made in close collaboration with the GPU vendor NVIDIA. The final shape of a complete QUonG deployment is an assembly of standard 42U racks, each one capable of 80 TFLOPS/rack of peak performance, at a cost of 5 k Euro-Sign /T F LOPS and for an estimated power consumption of 25 kW/rack. In this paper we report on the status of final rack deployment and on the R and D activities for 2012 that will focus on performance enhancement of the APEnet+ hardware through the adoption of new generation 28 nm FPGAs allowing the implementation of PCIe Gen3 host interface and the addition of new fault tolerance-oriented capabilities.
Design and development of the helicity injection system in Versatile Experiment Spherical Torus
International Nuclear Information System (INIS)
Park, JongYoon; An, Younghwa; Jung, Bongki; Lee, Jeongwon; Lee, HyunYoung; Chung, Kyoung-Jae; Na, Yong-Su; Hwang, Y.S.
2015-01-01
Graphical abstract: - Highlights: • A high current electron gun with single pulse power for both arc and extraction is developed. • The optimal gun operation is confirmed by impedance matching between the PFN and plasma. • The gun injected currents of 0.95 kA with the voltage of ∼410 V for 5 ms with a 1.2 kV PFN. • The helicity injection system using the gun has been developed and tested successfully in VEST. • Toroidal currents of up to 3.8 kA confirm possible relaxation into tokamak-like plasma. - Abstract: A helicity injection system for the Versatile Experiment Spherical Torus (VEST) has been successfully developed and commissioned. A high current electron gun utilizing hollow cathode and washer stacks has been designed and constructed with a single pulse power system that can provide voltages for both arc discharge and extraction sequentially. Tests for electron gun operation with the single pulse power system have been conducted under various toroidal and poloidal field strengths. The estimated plasma impedance, depending on the injection magnetic field structure, can be utilized for the optimal gun operation by impedance matching between the pulse power system and plasma. With the charging voltage of 1.2 kV, injection current of 0.95 kA has been obtained with the injection voltage of 410 V for about 5 ms. Initial helicity injection experiments have been conducted under various toroidal and poloidal field strengths and a toroidal plasma current of up to 3.8 kA is observed with the current multiplication larger than the geometric stacking ratio, confirming the possibility of relaxation into tokamak-like plasma with closed flux formation.