Assessment of industrial liquid waste management in Omdurman Industrial Area

Energy Technology Data Exchange (ETDEWEB)

Elnasri, R A. A. [Institute of Environmental Studies, University of Khartoum, Khartoum (Sudan)

2003-04-15

This study was conducted mainly to investigate the effects of industrial liquid waste on the environment in the Omdurman area. Various types of industries are found around Omdurman. According to the ISC the major industries are divided into eight major sub-sectors, each sub-sector is divided into types of industries. Special consideration was given to the liquid waste because of its effects. In addition to the available data, personal observation supported by photographs, laboratory analyses were carried on the industrial effluents. The investigated parameters in the analysis were, BOD, COD, O and G, Cr, TDS, TSS, pH, temp and conductivity. Interviews were conducted with waste handling workers in the industries, in order to assess the effects of industrial pollution. The results obtained showed that pollutants produced by all the factories were found to exceed the accepted levels of the industrial pollution control. The effluents disposed of in the sites allotted by municipal authorities have adverse effects on the surrounding environment and public health and amenities. Accordingly the study recommends that the waste water must be pretreated before being disposed of in site allotted by municipal authorities. Develop an appropriate system for industrial waste proper management. The study established the need to construct a sewage system in the area in order to minimize the pollutants from effluents. (Author)

Large area x-ray detectors for cargo radiography

Science.gov (United States)

Bueno, C.; Albagli, D.; Bendahan, J.; Castleberry, D.; Gordon, C.; Hopkins, F.; Ross, W.

2007-04-01

Large area x-ray detectors based on phosphors coupled to flat panel amorphous silicon diode technology offer significant advances for cargo radiologic imaging. Flat panel area detectors provide large object coverage offering high throughput inspections to meet the high flow rate of container commerce. These detectors provide excellent spatial resolution when needed, and enhanced SNR through low noise electronics. If the resolution is reduced through pixel binning, further advances in SNR are achievable. Extended exposure imaging and frame averaging enables improved x-ray penetration of ultra-thick objects, or "select-your-own" contrast sensitivity at a rate many times faster than LDAs. The areal coverage of flat panel technology provides inherent volumetric imaging with the appropriate scanning methods. Flat panel area detectors have flexible designs in terms of electronic control, scintillator selection, pixel pitch, and frame rates. Their cost is becoming more competitive as production ramps up for the healthcare, nondestructive testing (NDT), and homeland protection industries. Typically used medical and industrial polycrystalline phosphor materials such as Gd2O2S:Tb (GOS) can be applied to megavolt applications if the phosphor layer is sufficiently thick to enhance x-ray absorption, and if a metal radiator is used to augment the quantum detection efficiency and reduce x-ray scatter. Phosphor layers ranging from 0.2-mm to 1-mm can be "sandwiched" between amorphous silicon flat panel diode arrays and metal radiators. Metal plates consisting of W, Pb or Cu, with thicknesses ranging from 0.25-mm to well over 1-mm can be used by covering the entire area of the phosphor plate. In some combinations of high density metal and phosphor layers, the metal plate provides an intensification of 25% in signal due to electron emission from the plate and subsequent excitation within the phosphor material. This further improves the SNR of the system.

Industrial pollutions is an environmental issue of Karachi urban area

International Nuclear Information System (INIS)

Jokhio, M.H.; Abro, M.I.; Essani, A.

2005-01-01

The Industrial pollution is one of the serious Environmental issues of the Karachi urban area, categorized as air pollution and water pollution. The localization more the 6000 industries in Karachi urban area at four different sites of Sindh industrial trading estate, Landhi industrial trading estate, Korangi industrial area west Warf industrials, Port Qasim industrial. Area and Hub industrial are near Karachi city. The major iron and steel industries includes Pakistan steel mills and its allied industries at Bin Qasim more than 100 re-rolling industries are located at site area. Karachi ship yard engineering works, Peoples steel Mill, automobile industries and various manufacturing industries which requires metal and its alloy in manufacturing of product mostly located at Bin Qasim, Korangi, and Shershah site areas. None of the industrial sector contain the waster treatment or recycling plant. The ill planted growth of Karachi and its industries caused the environmental degradation of the city and its coastal areas complete with massive mangrove destruction, air water, fishing, and agriculture possessing a potential threat to the lives of more than 10 million citizens. The environmental issues of the metal related industries include the scrap, waste and pollution. Scrapes am waste of the metal industries can be reused in other manufacturing of engineering materials or recycled to produce the new material. However the pollution is the one of the major environmental issue related with the metal industries which need the considerable research and development work in order to over come the serve environmental issues of the urban areas. This article reviews and identifies the level of industrial pollution emphasized on metal related industries of the Karachi urban areas. (author)

ANALYSIS OF INVESTMENT ATTRACTIVENESS REDEVELOPMENT PROJECTS THE INDUSTRIAL AREAS IN KIEV

Directory of Open Access Journals (Sweden)

Yevsyukov T. O.

2017-08-01

Full Text Available At the present stage of development of land relations in major cities of our country important issue is the development of investment, attract and use foreign investment. According to the Law of Ukraine "On investment activity" under the investment necessary to understand "all types of property and intellectual values invested in business and other activities, which resulted in creating profit (income or social effect is achieved." For the economy of any city, including the city. Kyiv and development of urban land use, renovation of industrial areas deindustrialization of inefficient production centers, it is extremely important investment activity (foreign investment as one of the most effective mechanisms for the development and activities of national companies. The purpose of the article to analyze the investment attractiveness of the redevelopment projects of industrial areas to economic development of eco-industrial land use in Kiev, despite the downward trend in investment activity of domestic enterprises, the need for technical and technological modernization of production as well as the entire market infrastructure, redevelopment of industrial areas. Redevelopment areas – this is a comprehensive activity aimed at changing the existing construction work carried out with the help of large investments (investments in reconstruction; renovation of; overhaul; demolition; conversion; improving the environment, which results in a positive effect on economic, social and environmental aspects. Investment and construction projects related to redevelopment of industrial land use (objects in the management of the city, characterized by considerable risks given the high capital intensity, binding to a specific area, and the impact of other internal and external factors. That is why this investment activity should be ensured exceptional dynamic management to ensure the quality of implementation and the necessary level of profitability and

INDUSTRIAL AREA AS A BASIS FOR SPATIAL OPTIMIZATION OF LAND USE IN KIEV

Directory of Open Access Journals (Sweden)

Tsviakh О.

2017-02-01

Full Text Available In article deals with problem of using the urban land, including land under the industrial objects in Kiev. Also was analysed the ways of optimization the urban land using. Today become particularly acute the problem for efficient use of urban land use, including land for industrial facilities non-functioning as a reserve future development of Kyiv-based ecological-economic approach to solving them. However, to ensure sustainable development of urban population (preserve and improve health, improve working conditions, improve living conditions, increase the construction of social and affordable housing, reducing unemployment, creating new jobs, improving the ecological state of the environment within large cities , you need to identify ways to optimize existing urban land use. The complexity of management decisions is determined, above all, the fact that in most cities of Ukraine territorial resources are exhausted and vacant land plots require significant investment. Also, a significant proportion of non-functioning industrial enterprises, which occupy large areas in the city were in Kyiv surrounded by residential development, buffer zones, technogenic disturbed and contaminated land. These objects be removed outside the settlements and the land on which they are to be re-cultivated and restoration for more ecological, economically feasible and sustainable use. The rapid development of large cities around the world and increase their impact on the environment and society is accompanied by a set ekonominyh, environmental and social issues that significantly influence the development of land relations in settlements in general. Today in Kyiv observed the changing dynamics of land area, which is to reduce the share of agricultural and forestry purposes and to increase the territory of other categories. The process of de-industrialization and suburbanization of urban land use is inevitable. They in turn accelerate other processes - "crowding out

Performance evaluation of the conventional Brazilian industries radiation protection in the small industrial gauges and industrial radiography areas

International Nuclear Information System (INIS)

Santos, Joyra Amaral dos

1999-08-01

This works evaluates by punctuation the performance in conventional Brazilian industries radiation protection area which make use of small industrial gauges and industrial radiography. It proposes, procedures for industry self-evaluation, besides a new radiation protection plans pattern for the small industrial gauges area. The data source where inspection reports of Dosimetry Radiation Protection Institute/Nuclear Energy Commission conventional Brazilian industries' radiation protection plans, beyond visitation to the inspection place. The performance evaluation has been realized both in the administrative and operational aspects of the industries. About of 60% of the industries have a satisfactory register control which does not happen to the operational control. The performance evaluation advantage is that industries may self-evaluate, foreseeing Dosimetry Radiation Protection Institute's regulation inspections, correcting its irregularities, automatically improving its services. The number of industries which have obtained satisfactory performance in both areas is below 70%, both in administrative and operational aspects. Such number can be considered a low one as it is radiation protection. The procedures propose in this work aim to improve such a situation. (author)

Low Impact Development for Industrial Areas

Science.gov (United States)

2015-07-01

copper gutters can also be significant sources of metal pollutants. Other studies indicate that vehicle disc brake pads and car tires can be a...industrial areas to develop the performance criteria for LID systems that specifically targeted these areas. Areas targeted include scrap metal recycling

Monolayer graphene-insulator-semiconductor emitter for large-area electron lithography

Science.gov (United States)

Kirley, Matthew P.; Aloui, Tanouir; Glass, Jeffrey T.

2017-06-01

The rapid adoption of nanotechnology in fields as varied as semiconductors, energy, and medicine requires the continual improvement of nanopatterning tools. Lithography is central to this evolving nanotechnology landscape, but current production systems are subject to high costs, low throughput, or low resolution. Herein, we present a solution to these problems with the use of monolayer graphene in a graphene-insulator-semiconductor (GIS) electron emitter device for large-area electron lithography. Our GIS device displayed high emission efficiency (up to 13%) and transferred large patterns (500 × 500 μm) with high fidelity (industries and opening opportunities in nanomanufacturing.

Solution coating of large-area organic semiconductor thin films with aligned single-crystalline domains

KAUST Repository

Diao, Ying; Tee, Benjamin C-K.; Giri, Gaurav; Xu, Jie; Kim, Do Hwan; Becerril, Hector A.; Stoltenberg, Randall M.; Lee, Tae Hoon; Xue, Gi; Mannsfeld, Stefan C. B.; Bao, Zhenan

2013-01-01

Solution coating of organic semiconductors offers great potential for achieving low-cost manufacturing of large-area and flexible electronics. However, the rapid coating speed needed for industrial-scale production poses challenges to the control

Governing multi-actor decision processes in Dutch industrial area redevelopment

NARCIS (Netherlands)

Blokhuis, E.G.J.

2010-01-01

In the first part of the thesis, a literature review is presented. In this literature review, industrial areas in the Netherlands are discussed, leading to the conclusion that industrial areas are important for realizing sustainable economic growth in the Netherlands. Industrial areas play an

Radio transmission system for industrial area

International Nuclear Information System (INIS)

Iliescu, M.; Culcer, M.; Curuia, M.; Anghel, N.M.; Stefanescu, I.

2003-01-01

The paper deals with a data transmission system operating in a large, noisy industrial area. The radio transmission system permits data and commands communication between the local units of collecting data and a central monitoring and/or command station ( dispatch). The communication support are radio waves in the range 450 MHz. The transducers are of transmitter type, with 4-20 mA output signal, providing information about environmental and/or work parameters. Data are primarily acquisitioned in a data logger with microcontroller, then transmitted via a FSK radio modem and a radio station to the dispatch. Data logger can also be connected in a network. The dispatch personal computer receives and processes data and transmits commands. The system functioning is supervised by a communication software in MCS - 51 assembler and an application software in Visual C ++ . (author)

Market profile and conservation opportunity assessment for large industrial operations in Ontario

International Nuclear Information System (INIS)

Keyes, C.; Balbaa, I.; Cuthbert, D.; Young, D.

2006-01-01

In view of the expected electricity shortages in Ontario, there is an urgent need for not only new supply but also a significant increase in conservation and load shifting efforts. This report presented the results of a study focused on key technology or market areas that presented opportunities for implementation of energy efficient measures. The materials, analytical results, and outcomes of the study could be utilized as a framework for developing future program delivery models. The report provided a comprehensive market analysis for large industrial operations in Ontario. A market profile was presented for the following sectors: mining; pulp and paper; iron and steel; the chemical industry; petroleum refining; motor vehicle, body and parts manufacturing; cement; and food. Opportunities for conservation and demand management were identified. The report also presented an analysis and recommendations for energy conservation demand management and demand response applicable to large industry. Examples of programs in other jurisdictions in Canada as well as the United States were discussed. 34 refs., 7 tabs., 23 figs., 1 appendix.

Large-area WSe2 electric double layer transistors on a plastic substrate

KAUST Repository

Funahashi, Kazuma; Pu, Jiang; Li, Ming Yang; Li, Lain-Jong; Iwasa, Yoshihiro; Takenobu, Taishi

2015-01-01

Due to the requirements for large-area, uniform films, currently transition metal dichalcogenides (TMDC) cannot be used in flexible transistor industrial applications. In this study, we first transferred chemically grown large-area WSe2 monolayer films from the as-grown sapphire substrates to the flexible plastic substrates. We also fabricated electric double layer transistors using the WSe2 films on the plastic substrates. These transistors exhibited ambipolar operation and an ON/OFF current ratio of ∼104, demonstrating chemically grown WSe2 transistors on plastic substrates for the first time. This achievement can be an important first step for the next-generation TMDC based flexible devices. © 2015 The Japan Society of Applied Physics.

Large-area WSe2 electric double layer transistors on a plastic substrate

KAUST Repository

Funahashi, Kazuma

2015-04-27

Due to the requirements for large-area, uniform films, currently transition metal dichalcogenides (TMDC) cannot be used in flexible transistor industrial applications. In this study, we first transferred chemically grown large-area WSe2 monolayer films from the as-grown sapphire substrates to the flexible plastic substrates. We also fabricated electric double layer transistors using the WSe2 films on the plastic substrates. These transistors exhibited ambipolar operation and an ON/OFF current ratio of ∼104, demonstrating chemically grown WSe2 transistors on plastic substrates for the first time. This achievement can be an important first step for the next-generation TMDC based flexible devices. © 2015 The Japan Society of Applied Physics.

Identification of soybean genotypes adaptive to tropical area and suitable for industry

Science.gov (United States)

Adie, M. M.; Krisnawati, A.

2018-01-01

Soybeans in Indonesia are mostly used for raw material of tempeh industry. This study aims to identify 150 soybean genotypes for their suitability for raw materials of tempeh and adaptability to be developed in tropical area of Indonesia. The research material consisted of 150 soybean genotypes. The field research was conducted in Malang from February to May 2016, using a randomized block design with two replicates. The identification of 150 soybean genotypes showed 30.67% of super early maturity (soybeans with large seed size. In this research, G511H/Anj//Anj////Anjs-8-5 was suitable to be developed in Indonesia’s tropical climate and also preferred by industry for tempeh raw material due to its high yield, super early days to maturity, and large seed size.

Resilience of chemical industrial areas through attenuation-based security

International Nuclear Information System (INIS)

Reniers, G.L.L.; Sörensen, K.; Khan, F.; Amyotte, P.

2014-01-01

This paper investigates the possibility of attenuation-based security within chemical industrial areas. Representing chemical industrial areas as mathematical networks, we prove by case-study that the resilience to disaster of such areas may follow a power-law distribution. Furthermore, we examine what happens to the network when highly hazardous installations would be intelligently protected against malicious acts: the network disintegrates into separate smaller networks. Hence, islands are formed with no escalation danger in between. We conclude that it is possible to protect chemical industrial areas in such a way that they are more resilient against terrorism

Research progress on large-area perovskite thin films and solar modules

Directory of Open Access Journals (Sweden)

Zhichun Yang

2017-12-01

Full Text Available Organometal halide perovskites have exhibited a bright future as photovoltaic semiconductor in next generation solar cells due to their unique and promising physicochemical properties. Over the past few years, we have witnessed a tremendous progress of efficiency record evolution of perovskite solar cells (PSCs. Up to now, the highest efficiency record of PSCs has reached 22.1%; however, it was achieved at a very small device area of <0.1 cm2. With the device area increasing to mini-module scale, the efficiency record dropped dramatically. The inherent causes are mainly ascribed to inadequate quality control of large-area perovskite thin films and insufficient optimization of solar module design. In current stage of PSCs research and development, to overcome these two obstacles is in urgent need before this new technology could realize scale-up industrialization. Herein, we present an overview of recently developed strategies for preparing large-area perovskite thin films and perovskite solar modules (PSMs. At last, cost analysis and future application directions of PSMs have also been discussed.

Large area inkjet printing for organic photovoltaics and organic light emitting diodes using non-halogenated ink formulations

NARCIS (Netherlands)

Eggenhuisen, T.M.; Coenen, M.J.J.; Slaats, M.W.L.; Groen, W.A.

2014-01-01

The transfer of laboratory scale solution processing of organic electronics to large area roll-to-roll production requires the use of up-scalable deposition techniques. Furthermore, industrial production demands the omission of halogenated and other harmful solvents. Here, the authors discuss large

Site survey for large wind turbines in the Rijnmond area. Plaatsingsmogelijkheden grote windturbines in het Rijnmondgebied

Energy Technology Data Exchange (ETDEWEB)

Arkesteyn, L A; Van der Ham, P

1985-01-01

This paper reveals only preliminary results of a study on site selection for large wind turbines in a heavily industrialized and urbanized area of The Netherlands: the Rijnmond area. Factors like average wind speed, coupling to electric power grid, acquisition of land, noise pollution, safety aspects, avoiding harm to birds, and fitting in the existent physical structure of the area are evaluated.

Performance evaluation of the conventional Brazilian industries radiation protection in the small industrial gauges and industrial radiography areas; Sistema de avaliacao de desempenho em radioprotecao das industrias convencionais brasileiras nas areas de medidores nucleares e radiografia industrial

Energy Technology Data Exchange (ETDEWEB)

Santos, Joyra Amaral dos

1999-08-01

This works evaluates by punctuation the performance in conventional Brazilian industries radiation protection area which make use of small industrial gauges and industrial radiography. It proposes, procedures for industry self-evaluation, besides a new radiation protection plans pattern for the small industrial gauges area. The data source where inspection reports of Dosimetry Radiation Protection Institute/Nuclear Energy Commission conventional Brazilian industries' radiation protection plans, beyond visitation to the inspection place. The performance evaluation has been realized both in the administrative and operational aspects of the industries. About of 60% of the industries have a satisfactory register control which does not happen to the operational control. The performance evaluation advantage is that industries may self-evaluate, foreseeing Dosimetry Radiation Protection Institute's regulation inspections, correcting its irregularities, automatically improving its services. The number of industries which have obtained satisfactory performance in both areas is below 70%, both in administrative and operational aspects. Such number can be considered a low one as it is radiation protection. The procedures propose in this work aim to improve such a situation. (author)

Iron, Oil, and Emeryville: Resource Industrialization and Metropolitan Expansion in the San Francisco Bay Area, 1850-1900

OpenAIRE

Lunine, Seth

2013-01-01

Scholars have largely overlooked the formative role of industry in both California's economic development and the San Francisco Bay Area's metropolitan expansion during the late nineteenth century. Beginning in the early 1880s, leading firms in San Francisco's specialized industries, such as the iron and chemicals sectors, dispersed to the metropolitan periphery. This process of industrial suburbanization created an integrative metropolitan economy, as well as individual suburbs. In this di...

A sustainable approach for industrial area redevelopment in the Netherlands

NARCIS (Netherlands)

Blokhuis, E.G.J.; Schaefer, W.F.; Kungolos, A.; Brebbia, C.A.; Beriatos, E.

2007-01-01

According to the Dutch Ministry of Economic Affairs, creating space for industrial areas is necessary to realize a sustainable economic growth. Currently, the average time needed to redevelop an industrial area in the Netherlands is 10 years. Furthermore, almost 30% of the Dutch stock of industrial

Economical solution for the industrial waste problem of Karachi industrial area

International Nuclear Information System (INIS)

Mubin, S.

2005-01-01

The increased rate of industrialization coupled with rapid urbanization in Pakistan has given rise to serious water pollution and environmental problems. A vast range of industries has been established in the country during the last twenty five years, including tanneries, fertilizers, textiles, refineries, chemicals, vegetable oils, paper am pulp, sugar and food. Little attention was paid towards a large scale release of wastewater from these industries. Presently wastewater produced from these industries has been considered a serious problem and research in being conducted to solve its associated problems. Recently, it has been realized that there is a significant threat of water borne diseases, degradation of fresh water quality, environmental depletion and soil deterioration from the effluent and toxic emission of industries. Being a developing country and having limited resources, it is hard to install treatment plants on the industrial effluent with every industry before discharging them into streams which are also creating disturbance in natural ecosystem. An effort has been made to solve wastewater problem by implementing statistical tools on data of Karachi industrial state, obtained from EPA JICA and PCRWR, Islamabad. (author)

Large area self-powered gamma ray detector

International Nuclear Information System (INIS)

LeVert, F.E.

1994-01-01

The purpose of this research was to develop a large area self-powered gamma detector (LASPGD) capable of detecting the movement of sealed radiation sources into and out of industrial radiographic units and to construct a prototype source position monitor (SPM) for these units utilizing the LASPGD. Prototype isotropic and directional LASPGDs, with solid and inert gas dielectrics, were developed and extensively tested using calibrated gamma sources (i.e., Cs-137, and Co-60). The sensitivities of the isotropic detectors, with inert gas dielectrics, were found to be approximately a factor of ten greater than those measured for the solid dielectric LASPGDs. Directionally sensitive self-powered detectors were found to exhibit a forward-to-back hemispherical sensitivity ratio of approximately 2 to 1. Industrial radiographic units containing Ir-192 sources with different activities were used to test the performance of the SPM. The SPM, which utilized a gas dielectric LASPGD, performed as designed. That is, the current generated in the LASPGD was converted to a voltage, amplified and used to control the on/off state of an incandescent lamp. The incandescent lamp, which functions as the source/out warning indicator, flashes at a rate of one flash per second when the source is in use (i.e. out of its shield)

Reactive power compensation and loss reduction in large industrial enterprises

Energy Technology Data Exchange (ETDEWEB)

Jovanovic, S; Gajic, B; Mijailovic, S [Institute Nikola Tesla, Beograd (Yugoslavia)

1991-12-01

This paper considers the reactive power compensation and the active power and energy loss reduction of large radial power networks in the Serbian mine and smelting industry. It gives an efficient optimization procedure for positioning and sizing capacitors in large industrial systems integrated with a simple network analysis method. (Author).

Large area damage testing of optics

International Nuclear Information System (INIS)

Sheehan, L.; Kozlowski, M.; Stolz, C.

1996-01-01

The damage threshold specifications for the National Ignition Facility will include a mixture of standard small-area tests and new large-area tests. During our studies of laser damage and conditioning processes of various materials we have found that some damage morphologies are fairly small and this damage does not grow with further illumination. This type of damage might not be detrimental to the laser performance. We should therefore assume that some damage can be allowed on the optics, but decide on a maximum damage allowance of damage. A new specification of damage threshold termed open-quotes functional damage thresholdclose quotes was derived. Further correlation of damage size and type to system performance must be determined in order to use this measurement, but it is clear that it will be a large factor in the optics performance specifications. Large-area tests have verified that small-area testing is not always sufficient when the optic in question has defect-initiated damage. This was evident for example on sputtered polarizer and mirror coatings where the defect density was low enough that the features could be missed by standard small- area testing. For some materials, the scale-length at which damage non-uniformities occur will effect the comparison of small-area and large-area tests. An example of this was the sub-aperture tests on KD*P crystals on the Beamlet test station. The tests verified the large-area damage threshold to be similar to that found when testing a small-area. Implying that for this KD*P material, the dominate damage mechanism is of sufficiently small scale-length that small-area testing is capable of determining the threshold. The Beamlet test station experiments also demonstrated the use of on-line laser conditioning to increase the crystals damage threshold

Industrial Physics Careers: A Large Company Perspective

Science.gov (United States)

Zollner, Stefan

2009-03-01

Statistical data from the American Institute of Physics and the National Science Foundation show that only about a third of physics graduates get permanent jobs in academia. A few work in government labs and hospitals. The majority of physics Ph.D.s, however, find employment in the private sector (industry). This trend has been increasing, i.e., recent Ph.D.s are even more likely to start careers in industry. Industrial physicists work in small, medium or large companies in a broad range of fields, including aerospace, semiconductors, automotive, energy, information technology, contract research, medical, chemical, optics, etc. They are also represented in fields outside of physics, such as finance. Even the ``inventor'' of the Powerball lottery game is a Ph.D. physicist. In my talk, I will describe pathways to success for an industrial physicist, from the perspective of employment in three different large corporations. Based on the NIST Baldridge criteria of Performance Excellence, I will discuss how to achieve and measure organizational success through focus on products and customers. Individual performance is linked to the goals of the organization. Performance has two components: Goals and behaviors. Both are key to success as an individual contributor or manager.[4pt] References: [0pt] http://www.aip.org/statistics/trends/emptrends.html [0pt] http://www.aps.org/about/governance/committees/commemb/index.cfm [0pt] http://www.quality.nist.gov/

Long-term airborne contamination studied by attic dust in an industrial area: Ajka, Hungary

Science.gov (United States)

Völgyesi, P.; Jordan, G.; Szabo, Cs.

2012-04-01

Heavy industrial activities such as mining, metal industry, coal fired power plants have produced large amount of by-products and wide-spread pollution, particularly in the period of centrally dictated economy after WWII, in Hungary. Several studies suggest that significant amount of these pollutants have been deposited in the urban environment. Nowadays, more than half of the world's population is living in urban areas and people spend almost 80% of their lives indoors in developed countries increasing human health risk due to contamination present in urban dwellings. Attic dust sampling was applied to determine the long-term airborne contamination load in the industrial town of Ajka (Hungary). There has been a high industrial activity in Ajka since the end of the 19th century. In addition to aluminum and alumina industry, coal mining, coal fired power plant and glass industry sites, generated numerous waste heaps which act as multi-contamination sources in the area. In October 2010 the Ajka red mud tailings pond failed and caused an accidental regional contamination of international significance. The major objective of this research was to study and map the spatial distribution of heavy metal contamination in airborne attic dust samples. At 27 sampling sites 30 attic dust samples were collected. Sampling strategy followed a grid-based stratified random sampling design. In each cell a house for attic dust sample collection was selected that was located the closest to a randomly generated point in the grid cell. The project area covers a 8x8 grid of 1x1 km cells with a total area of 64 km2. In order to represent long-term industrial pollution, houses with attics kept intact for at least 30-40 years were selected for sampling. Sampling included the collection of background samples remotely placed from the industrialized urban area. The concentration of the major and toxic elements (Al, Ca, Fe, K, Mg, Mn, Na, P, S, and As, Ba, Cd, Co, Cr, Cu, Li, Mo, Ni, Pb, Se, Sn

Polycyclic aromatic hydrocarbons (PAHs) in a large South American industrial coastal area (Santos Estuary, Southeastern Brazil): Sources and depositional history

International Nuclear Information System (INIS)

Martins, Cesar C.; Bicego, Marcia C.; Mahiques, Michel M.; Figueira, Rubens C.L.; Tessler, Moyses G.; Montone, Rosalinda C.

2011-01-01

Highlights: → In early 1980s, Santos Estuary became known as one of the worst polluted in the world. → PAHs levels were similar to the values reported for marine sediments worldwide. → PAHs analyses indicated multiple sources of these compounds (oil and pyrolitic origin). → The decline of oil consumption due to the world oil crisis (late 1970s) was shown. → The input of organic pollutants is a historical problem for the Santos Estuary. - Abstract: Located in southeastern Brazil, the Santos Estuary has the most important industrial and urban population area of South America. Since the 1950's, increased urbanization and industrialization near the estuary margins has caused the degradation of mangroves and has increased the discharge of sewage and industrial effluents. The main objectives of this work were to determine the concentrations and sources of polycyclic aromatic hydrocarbons (PAHs) in sediment cores in order to investigate the input of these substances in the last 50 years. The PAHs analyses indicated multiple sources of these compounds (oil and pyrolitic origin), basically anthropogenic contributions from biomass, coal and fossil fuels combustion. The distribution of PAHs in the cores was associated with the formation and development of Cubatao industrial complex and the Santos harbour, waste disposal, world oil crisis and the pollution control program, which results in the decrease of organic pollutants input in this area.

Heavy metal contamination in the vicinity of an industrial area near Bucharest.

Science.gov (United States)

Velea, Teodor; Gherghe, Liliana; Predica, Vasile; Krebs, Rolf

2009-08-01

Heavy metals such as lead are well known to cause harmful health effects. Especially children are particularly susceptible to increased levels of lead in their blood. It is also a fact that lead concentration is increasing in the environment due to increased anthropogenic activity. The risk of heavy metal contamination is pronounced in the environment adjacent to large industrial complexes. In a combined case study, the environmental pollution by heavy metals was related to children's health in the vicinity of an industrial area located 4 km south-east from Bucharest about 2 km east from the nearest town-Pantelimon. This site includes companies processing different, nonferrous solid wastes for recovery of heavy metals and producing different nonferrous alloys and lead batteries. In this paper, mainly the results of environmental sampling and analyses are summarized. Water, soil, and atmospheric deposition samples were collected from different locations within 3 km from the industrial area. For comparison, samples were also taken from Bucharest. Water samples were filtered (open collecting pots were used on nine different sites between August and November 2006. At most sampling locations, the heavy metal concentrations in soil decrease with increasing distance to the presumably major source of pollution. Highest heavy metal concentrations were found in 10-20 cm soil depths. There were also decreasing heavy metal concentrations for atmospheric deposition with increasing distance to the industrial site. In surface and groundwater samples, traces of zinc, copper and lead were detected. The heavy metal concentrations in soil were increased in the study area, mostly under legal action limits in low-concern areas (e.g., 1,000 mg Pb/kg dry soil), but often above action limits for high-concern areas (100 mg Pb/kg dry soil) such as populated areas. The soluble lead concentrations in water samples indicate a need for monitoring and assessing water quality in more detail. The

Solution Coating of Superior Large-Area Flexible Perovskite Thin Films with Controlled Crystal Packing

KAUST Repository

Li, Jianbo

2017-05-08

Solution coating of organohalide lead perovskites offers great potential for achieving low-cost manufacturing of large-area flexible optoelectronics. However, the rapid coating speed needed for industrial-scale production poses challenges to the control of crystal packing. Herein, this study reports using solution shearing to confine crystal nucleation and growth in large-area printed MAPbI3 thin films. Near single-crystalline perovskite microarrays are demonstrated with a high degree of controlled macroscopic alignment and crystal orientation, which exhibit significant improvements in optical and optoelectronic properties comparing with their random counterparts, spherulitic, and nanograined films. In particular, photodetectors based on the confined films showing intense anisotropy in charge transport are fabricated, and the device exhibits significantly improved performance in all aspects by one more orders of magnitude relative to their random counterparts. It is anticipated that perovskite films with controlled crystal packing may find applications in high-performance, large-area printed optoelectronics, and solar cells.

3D-Printed Disposable Wireless Sensors with Integrated Microelectronics for Large Area Environmental Monitoring

KAUST Repository

Farooqui, Muhammad Fahad

2017-05-19

Large area environmental monitoring can play a crucial role in dealing with crisis situations. However, it is challenging as implementing a fixed sensor network infrastructure over large remote area is economically unfeasible. This work proposes disposable, compact, dispersible 3D-printed wireless sensor nodes with integrated microelectronics which can be dispersed in the environment and work in conjunction with few fixed nodes for large area monitoring applications. As a proof of concept, the wireless sensing of temperature, humidity, and H2S levels are shown which are important for two critical environmental conditions namely forest fires and industrial leaks. These inkjet-printed sensors and an antenna are realized on the walls of a 3D-printed cubic package which encloses the microelectronics developed on a 3D-printed circuit board. Hence, 3D printing and inkjet printing are uniquely combined in order to realize a low-cost, fully integrated wireless sensor node.

Solution Coating of Superior Large-Area Flexible Perovskite Thin Films with Controlled Crystal Packing

KAUST Repository

Li, Jianbo; Liu, Yucheng; Ren, Xiaodong; Yang, Zhou; Li, Ruipeng; Su, Hang; Yang, Xiaoming; Xu, Junzhuo; Xu, Hua; Hu, Jian-Yong; Amassian, Aram; Zhao, Kui; Liu, Shengzhong Frank

2017-01-01

Solution coating of organohalide lead perovskites offers great potential for achieving low-cost manufacturing of large-area flexible optoelectronics. However, the rapid coating speed needed for industrial-scale production poses challenges to the control of crystal packing. Herein, this study reports using solution shearing to confine crystal nucleation and growth in large-area printed MAPbI3 thin films. Near single-crystalline perovskite microarrays are demonstrated with a high degree of controlled macroscopic alignment and crystal orientation, which exhibit significant improvements in optical and optoelectronic properties comparing with their random counterparts, spherulitic, and nanograined films. In particular, photodetectors based on the confined films showing intense anisotropy in charge transport are fabricated, and the device exhibits significantly improved performance in all aspects by one more orders of magnitude relative to their random counterparts. It is anticipated that perovskite films with controlled crystal packing may find applications in high-performance, large-area printed optoelectronics, and solar cells.

E-COMMERCE AREA FOR TEXTILE INDUSTRY

OpenAIRE

R. M. Aileni; D. Farima; M. Ciocoiu

2011-01-01

This paper presents some management aspects concerning the e-commerce area for textile industry.Here it can have database management – customers, products and brand visualisation management. The databasemanagement can be doing by using a database management system. For database management it was use therelational model based on first-order predicate logic [1]. In this paper it was analyzed the relational databasemodel. The e-commerce area is born from need to simplify the buying and selling g...

Spatial clustering of knowledge-based industries in the Helsinki Metropolitan Area

Directory of Open Access Journals (Sweden)

Juan Eduardo Chica

2016-01-01

Full Text Available The central locations of metropolitan areas have some specific attributes, leading to an accumulation of large knowledge exchanges and extensive knowledge externalities, which encourage the concentration of various economic activities, especially knowledge-based industries (KBI. Other agglomeration economies found in metropolitan areas – such as telecommunications and transport infrastructures connected to global productive circuits and complementary labour markets – are key factors for KBI employment growth. This paper explores the Helsinki Metropolitan Area’s (HMA spatial clustering of KBI at the sub-district level, and the role played by agglomeration economies (both specialization and diversity economies in fostering this process. The results reveal that KBI employment shows patterns of concentration in the core and adjacent areas. The specialization and diversity economies found in the metropolitan core and the specialization economies found in others areas lead to KBI spatial clustering in the HMA. Public policies regarding the promotion of science parks have also played a decisive role.

An Indium-Free Anode for Large-Area Flexible OLEDs: Defect-Free Transparent Conductive Zinc Tin Oxide

NARCIS (Netherlands)

Morales-Masis, M.; Dauzou, F.; Jeangros, Q.; Dabirian, A.; Lifka, H.; Gierth, R.; Ruske, M.; Moet, D.; Hessler-Wyser, A.; Ballif, C.

2016-01-01

Flexible large-area organic light-emitting diodes (OLEDs) require highly conductive and transparent anodes for efficient and uniform light emission. Tin-doped indium oxide (ITO) is the standard anode in industry. However, due to the scarcity of indium, alternative anodes that eliminate its use are

Environmental impact of industrial wastes on marine area, case study: Port Sudan coastal area

International Nuclear Information System (INIS)

Abdalrahman, E. A. H.

2004-05-01

This study was carried out to determine the effect of the industrial wastes on marine environment in Port Sudan area. A very intensive study has been made to identify types of pollutions drained in seawater at study area of Red Sea coast. Samples were taken from three stations (1, 2 and 3) at study area and the following analysis were made: Temperature, salinity, hydrogen ion concentration, dissolved oxygen, biochemical oxygen demand, nutrient, oil and grease. The laboratory results revealed that wastes pollute the marine environment as the cooling water from studied industries which is drain into the seawater increases the degree of temperature approximately from 6 to 12 C degree above the allowed rate, the matter which was adverse effect on the environment and living marine creatures due to the sudden change of temperature degree. Also, it was found that the great amount of oil spills discharged into seawater due to many factors such as: cooling water, oil spills from ships and loading and discharging operations of crude oil ships. Accordingly these oils spills might have a deadly effect on living marine creatures, which have been mention in details through out this research. Hence, and to minimize this adverse effect of industrial wastes and others on the marine environment, may recommend to the following: Pretreatment to the industrial wastes should be taking before its draining into the Red Sea coastal area. Surveillance all ships into the port and observing loading and discharging operations as well as those ships in the regional waters and implementing the international maritime laws. Enlightenment the industrial administrators and manpower working with them about the severity which will definitely cause the marine environmental deterioration as a result of industrial wastes. To punish every one who violates the laws of environment protection. Thus, can be safeguarding the environment from pollutions and consequently develop the natural resources and proceed

Radiation protection program of Petrobras in industrial radiography area

International Nuclear Information System (INIS)

Signorini, M.

1988-01-01

Industrial hygiene has as main purpose the preservation of employees physical integrity when exposed to certain agressive agents. PETROBRAS Industrial hygiene program forecasts preventive policies in several specific fields. For the ionizing radiations area it was developed the ''Radiologic Protection Program'' which also deals with specific actions in industrial radiography jobs. These actions are hereinafter presented. (C.M.) [pt

The refinery industry within the Mediterranean area

International Nuclear Information System (INIS)

1999-01-01

During the period 1997-1998 Ome (Observatorie Mediterraneen de l'Energie) within a working group which was formed by the experts among the associated companies, has carried on an analysis on the prospects of refinery industry in the Mediterranean area in view of 2010. The aim of this study was to make clear, to the different operators, the consequences of the political choices in investments on refinery industry in the context of the progressive liberalization of the sector [it

Large catchment area recharges Titan's Ontario Lacus

Science.gov (United States)

Dhingra, Rajani D.; Barnes, Jason W.; Yanites, Brian J.; Kirk, Randolph L.

2018-01-01

We seek to address the question of what processes are at work to fill Ontario Lacus while other, deeper south polar basins remain empty. Our hydrological analysis indicates that Ontario Lacus has a catchment area spanning 5.5% of Titan's surface and a large catchment area to lake surface area ratio. This large catchment area translates into large volumes of liquid making their way to Ontario Lacus after rainfall. The areal extent of the catchment extends to at least southern mid-latitudes (40°S). Mass conservation calculations indicate that runoff alone might completely fill Ontario Lacus within less than half a Titan year (1 Titan year = 29.5 Earth years) assuming no infiltration. Cassini Visual and Infrared Mapping Spectrometer (VIMS) observations of clouds over the southern mid and high-latitudes are consistent with precipitation feeding Ontario's large catchment area. This far-flung rain may be keeping Ontario Lacus filled, making it a liquid hydrocarbon oasis in the relatively dry south polar region.

Understanding inter-industry wage structures in the euro area

OpenAIRE

Genre, Véronique; Momferatou, Daphne; Kohn, Karsten

2009-01-01

This paper focuses on the euro area wage structure and its potential determinants from a sectoral viewpoint. Merging information from the OECD Structural Analysis database with data from the EU Labour Force Survey, we construct a cross-country panel of 22 industries in 8 euro area countries for 1991-2002. Data inspection confirms the existence of a fairly stable inter- industry wage structure that is similar across countries. We then apply panel data techniques to identify factors explaining ...

Chemical industrial areas and their dynamic danger behaviour

NARCIS (Netherlands)

Reniers, Genserik L L; Audenaert, Amaryllis; Dullaert, W.; Soudan, K.

2007-01-01

Chemical industrial areas or so-called chemical clusters consist of various companies situated next to each other. Such areas are composed of hundreds of chemical installations exhibiting danger to a certain degree for initiating or continuing knock-on effects. In this paper, a methodology to model

Polybrominated diphenyl ethers in water, sediment, soil, and biological samples from different industrial areas in Zhejiang, China

International Nuclear Information System (INIS)

Wang, Junxia; Lin, Zhenkun; Lin, Kuangfei; Wang, Chunyan; Zhang, Wei; Cui, Changyuan; Lin, Junda; Dong, Qiaoxiang; Huang, Changjiang

2011-01-01

Highlights: ► We examined PBDE concentrations in various matrices from different industrial areas. ► Elevated PBDE levels were found in areas with low-voltage electrical manufactures. ► Areas with e-waste recycling activities also had higher PBDE concentrations. ► PBDE content and composition in water samples varied from one area to another. ► PBDE composition in sediment/soil and biological samples was predominated by BDE-209. - Abstract: Polybrominated diphenyl ethers (PBDEs) have been used extensively in electrical and electronic products, but little is known about their distribution in the environment surrounding the manufacturing factories. This study reports PBDE contamination in various matrices from the location (Liushi, Zhejiang province) that produces more than 70% of the low-voltage electrical appliances in China. Additionally, PBDE contamination was compared with other industries such as the e-waste recycling business (Fengjiang) in the same region. Specifically, we measured seven PBDE congeners (BDEs – 47, 99, 100, 153, 154, 183, and 209) in water, sediment, soil, plant, and animal tissues from four different areas in this region. The present study revealed elevated PBDE concentrations in all matrices collected from Liushi and Fengjiang in comparison with highly industrialized areas without significant PBDE contamination sources. In water samples, there were large variations of PBDE content and composition across different areas. In sediment/soil and biological samples, BDE-209 was the predominant congener and this could be due to the abundant usage of deca-BDE mixtures in China. Our findings provide the very first data on PBDE contamination in the local environments surrounding the electronics industry, and also reveal widespread PBDE contamination in highly industrialized coastal regions of China.

Contribution of Fugitive Emissions for PM10 Concentrations in an Industrial Area of Portugal

Science.gov (United States)

Marta Almeida, Susana; Viana Silva, Alexandra; Garcia, Silvia; Miranda, Ana Isabel

2013-04-01

Significant atmospheric dust arises from the mechanical disturbance of granular material exposed to the air. Dust generated from these open sources is termed "fugitive" because it is not discharged to the atmosphere in a confined flow stream. Common sources of fugitive dust include unpaved roads, agricultural tilling operations, aggregate storage piles, heavy construction and harbor operations. The objective of this work was to identify the likeliness and extend of the PM10 limit value exceedences due to fugitive emissions in a particularly zone where PM fugitive emissions are a core of environmental concerns - Mitrena, Portugal. Mitrena, is an industrial area that coexists with a high-density urban region (Setúbal) and areas with an important environmental concern (Sado Estuary and Arrábida which belongs to the protected area Natura 2000 Network). Due to the typology of industry sited in Mitrena (e.g. power plant, paper mill, cement, pesticides and fertilized productions), there are a large uncontrolled PM fugitive emissions, providing from heavy traffic and handling and storage of raw material on uncover stockyards in the harbor and industries. Dispersion modeling was performed with the software TAPM (The Air Pollution Model) and results were mapped over the study area, using GIS (Geographic Information Systems). Results showed that managing local particles concentrations can be a frustrating affair because the weight of fugitive sources is very high comparing with the local anthropogenic stationary sources. In order to ensure that the industry can continue to meet its commitments in protecting air quality, it is essential to warrant that the characteristics of releases from all fugitive sources are fully understood in order to target future investments in those areas where maximum benefit will be achieved.

[Pollution-ecological problems of old industrial and mining areas and future research prospects].

Science.gov (United States)

Zhou, Qixing

2005-06-01

Environmental pollution and its solicitation in ecological problems of old industrial and mining areas have become a worldwide technological puzzle restricting sustainable economic and social development. But, the definition and category of old industrial and mining areas is still disputed as an important concept. In this paper, the concept of old industrial and mining area was discussed in theory, and, proceeded with analyzing the complexity of current situation and environmental pollution problems of old industrial and mining areas in China, more keystone attention was paid to the secondary pollution problems from old industrial and mining areas as an important frontier of science. On the basis of expounding the complexity and characters of environmental pollution in old industrial and mining areas, it was suggested that as two key scientific problems in environmental sciences and ecology, the formation mechanisms and control technology of secondary pollution in old industrial and mining areas and the responses of new-type diseases to environmental pollution based on molecular ecotoxicology should be systematically studied on the national scale, and be an important component of environmental protection strategy in China in the future.

iBILL: Using iBeacon and Inertial Sensors for Accurate Indoor Localization in Large Open Areas

OpenAIRE

Wu, Xudong; Shen, Ruofei; Fu, Luoyi; Tian, Xiaohua; Liu, Peng; Wang, Xinbing

2017-01-01

As a key technology that is widely adopted in location-based services (LBS), indoor localization has received considerable attention in both research and industrial areas. Despite the huge efforts made for localization using smartphone inertial sensors, its performance is still unsatisfactory in large open areas, such as halls, supermarkets, and museums, due to accumulated errors arising from the uncertainty of users’ mobility and fluctuations of magnetic field. Regarding that, this paper pre...

Solid waste management in Khartoum industrial area

International Nuclear Information System (INIS)

Elsidig, N. O. A.

2004-05-01

This study was conducted in Khartoum industrial area (KIA). The study discusses solid waste generation issues in KIA as well as solid waste collection, storage, transport and final disposal methods. A focus on environmental impact resulting from the accumulation of solid waste was presented by reviewing solid waste management in developed as well as developing countries starting from generation to final disposal. Environmental health legislation in Sudan was investigated. The study covers all the (eight) industrial sub-sectors presented in KIA. The main objective of the study is to assess the situation of solid waste in KIA. To fulfill the objectives of the study the researcher deemed it necessary to explore problems related to solid waste generation and solid waste arrangement with special emphasis on final disposal methods. Practically, 31 (thirty-one) factories representing the different industrial sub-sectors in KIA were studied. This represents 25% of the total number of factories located in KIA. Data were obtained by, questionnaires, interviews and observations mainly directed to concerned officials, solid waste workers, pickers and brokers. Obtained data were stored, coded, tabulated and analyzed using the computer systems (excel and SPSS programmes). The obtained results should clear deficiency in the management of solid waste which led to great environmental deterioration in KIA and neighboring residential areas. The environment in studied area is continuously polluted due to high pollution loads and unproved solid waste management. In order to maintain health environment operating factories have to pretreated their solid waste according to the recognized standards and waste minimization techniques such as recycling and re use should be widely applied, moreover, running crash programme for environmental sanitation in Khartoum state should be expanded and improved to include special characteristics of solid waste from industries. Finally, increase awareness

Climate Variability and Industrial-Suburban Heat Environment in a Mediterranean Area

Directory of Open Access Journals (Sweden)

Giuseppina A. Giorgio

2017-05-01

Full Text Available The Urban Heat Island (UHI phenomenon prevalently concerns industrialized countries. It consists of a significant increase in temperatures, especially in industrialized and urbanized areas, in particular, during extreme warm periods like summer. This paper explores the climate variability of temperatures in two stations located in Matera city (Southern Italy, evaluating the increase in temperatures from 1988 to 2015. Moreover, the Corine Land Covers (1990–2000–2006–2012 were used in order to investigate the effect of land use on temperatures. The results obtained confirm the prevalence of UHI phenomena for industrialized areas, highlighting the proposal that the spreading of settlements may further drive these effects on the microclimate. In particular, the presence of industrial structures, even in rural areas, shows a clear increase in summer maximum temperatures. This does not occur in the period before 2000, probably due to the absence of the industrial settlement. On the contrary, from 2000 to 2015, changes are not relevant, but the maximum temperatures have always been higher than in the suburban area (station localized in green zone during daylight hours.

Transfer and characterization of large-area CVD graphene for transparent electrode applications

DEFF Research Database (Denmark)

Whelan, Patrick Rebsdorf

addresses key issues for industrial integration of large area graphene for optoelectronic devices. This is done through optimization of existing characterization methods and development of new transfer techniques. A method for accurately measuring the decoupling of graphene from copper catalysts...... and the electrical properties of graphene after transfer are superior compared to the standard etching transfer method. Spatial mapping of the electrical properties of transferred graphene is performed using terahertz time-domain spectroscopy (THz-TDS). The non-contact nature of THz-TDS and the fact...

A study about the prevalence and the related factors of metabolic syndrome and fatty liver comparing the urban area to tbe industrial area

Energy Technology Data Exchange (ETDEWEB)

Jeong, Hyo Eun; Cho, Pyong Kon [Dept. of of Radiological Science, Catholic University of Daegu. Daegu (Korea, Republic of)

2016-09-15

As the tertiary industry is being developed, many problems are introduced in an industrial area in Korea. This study aims to investigate the residents' health conditions, such as the prevalence of metabolic syndrome and fatty liver diagnosed by ultrasonography, comparing the urban with the industrial areas. The subjects were 378 adults in the urban area and 376 adults in the industrial area. Subject variables accounted for were gender, age, drinking habits, smoking habits, physical activities, waist circumferences and BMI. In blood tests, fasting blood glucose, triglyceride, HDL, blood pressures, total cholesterol, AST, ALT and GGT were examined. Also, the presence and absence of fatty liver, diagnosed using ultrasonography, was investigated. As a result, the prevalence of metabolic syndrome were 43.7% in the urban area and 51.6% in the industrial area, hence it was significantly higher in the industrial area than in the urban area. Fasting blood glucose, triglyceride and waist circumference in the distribution of the individual components were 47.4, 53.7, and 16.1% in the urban area and 54.5, 61.5, and 22.9% in the industrial area respectively, so it was substantially higher in the industrial area than in the urban area. On the other hand, HDL, diastolic blood pressure, and fatty liver were 25.7, 43.4, and 44.7% in the urban area and 21.3, 19.9, and 36.7% in the industrial area respectively and thus it was much higher in the urban area than in the industrial area. In conclusion, this study shows that there were significant differences between the residents' health condition, comparing the urban area to the industrial area. Therefore, the precaution and aggressive management of metabolic syndrome may be necessary, in accordance with the characteristics of the industrial zone.

A study about the prevalence and the related factors of metabolic syndrome and fatty liver comparing the urban area to tbe industrial area

International Nuclear Information System (INIS)

Jeong, Hyo Eun; Cho, Pyong Kon

2016-01-01

As the tertiary industry is being developed, many problems are introduced in an industrial area in Korea. This study aims to investigate the residents' health conditions, such as the prevalence of metabolic syndrome and fatty liver diagnosed by ultrasonography, comparing the urban with the industrial areas. The subjects were 378 adults in the urban area and 376 adults in the industrial area. Subject variables accounted for were gender, age, drinking habits, smoking habits, physical activities, waist circumferences and BMI. In blood tests, fasting blood glucose, triglyceride, HDL, blood pressures, total cholesterol, AST, ALT and GGT were examined. Also, the presence and absence of fatty liver, diagnosed using ultrasonography, was investigated. As a result, the prevalence of metabolic syndrome were 43.7% in the urban area and 51.6% in the industrial area, hence it was significantly higher in the industrial area than in the urban area. Fasting blood glucose, triglyceride and waist circumference in the distribution of the individual components were 47.4, 53.7, and 16.1% in the urban area and 54.5, 61.5, and 22.9% in the industrial area respectively, so it was substantially higher in the industrial area than in the urban area. On the other hand, HDL, diastolic blood pressure, and fatty liver were 25.7, 43.4, and 44.7% in the urban area and 21.3, 19.9, and 36.7% in the industrial area respectively and thus it was much higher in the urban area than in the industrial area. In conclusion, this study shows that there were significant differences between the residents' health condition, comparing the urban area to the industrial area. Therefore, the precaution and aggressive management of metabolic syndrome may be necessary, in accordance with the characteristics of the industrial zone

Large area high-speed metrology SPM system

International Nuclear Information System (INIS)

Klapetek, P; Valtr, M; Martinek, J; Picco, L; Payton, O D; Miles, M; Yacoot, A

2015-01-01

We present a large area high-speed measuring system capable of rapidly generating nanometre resolution scanning probe microscopy data over mm 2 regions. The system combines a slow moving but accurate large area XYZ scanner with a very fast but less accurate small area XY scanner. This arrangement enables very large areas to be scanned by stitching together the small, rapidly acquired, images from the fast XY scanner while simultaneously moving the slow XYZ scanner across the region of interest. In order to successfully merge the image sequences together two software approaches for calibrating the data from the fast scanner are described. The first utilizes the low uncertainty interferometric sensors of the XYZ scanner while the second implements a genetic algorithm with multiple parameter fitting during the data merging step of the image stitching process. The basic uncertainty components related to these high-speed measurements are also discussed. Both techniques are shown to successfully enable high-resolution, large area images to be generated at least an order of magnitude faster than with a conventional atomic force microscope. (paper)

Large area high-speed metrology SPM system

Science.gov (United States)

Klapetek, P.; Valtr, M.; Picco, L.; Payton, O. D.; Martinek, J.; Yacoot, A.; Miles, M.

2015-02-01

We present a large area high-speed measuring system capable of rapidly generating nanometre resolution scanning probe microscopy data over mm2 regions. The system combines a slow moving but accurate large area XYZ scanner with a very fast but less accurate small area XY scanner. This arrangement enables very large areas to be scanned by stitching together the small, rapidly acquired, images from the fast XY scanner while simultaneously moving the slow XYZ scanner across the region of interest. In order to successfully merge the image sequences together two software approaches for calibrating the data from the fast scanner are described. The first utilizes the low uncertainty interferometric sensors of the XYZ scanner while the second implements a genetic algorithm with multiple parameter fitting during the data merging step of the image stitching process. The basic uncertainty components related to these high-speed measurements are also discussed. Both techniques are shown to successfully enable high-resolution, large area images to be generated at least an order of magnitude faster than with a conventional atomic force microscope.

Chemical composition of sewage sludge of domestic and industrial areas of Hyderabad

International Nuclear Information System (INIS)

Ansari, T.P.; Kazi, T.G.; Kazi, G.H.

2001-01-01

A study on chemical composition sewage sludge of domestic and industrial areas of Hyderabad city has been carried out. The sludge samples were collected from various domestic and industrial areas of Hyderabad, over a period of 3 months. Analysis of sludge samples for different micro-nutrients and toxic elements has been accomplished by reliable analytical methods using atomic absorption, UV and colorimeter. It is observed that the levels of copper, nickel, zinc, lead and cadmium are higher in sludge samples of industrial area than those of domestic areas of Hyderabad. (author)

LYCORIS - A Large Area Strip Telescope

CERN Document Server

Krämer, U; Stanitzki, M; Wu, M

2018-01-01

The LYCORIS Large Area Silicon Strip Telescope for the DESY II Test Beam Facility is presented. The DESY II Test Beam Facility provides elec- tron and positron beams for beam tests of up to 6 GeV. A new telescope with a large 10 × 20 cm2 coverage area based on a 25 μm pitch strip sensor is to be installed within the PCMAG 1 T solenoid. The current state of the system is presented.

Polybrominated diphenyl ethers in water, sediment, soil, and biological samples from different industrial areas in Zhejiang, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Junxia; Lin, Zhenkun [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Lin, Kuangfei [School of Resources and Environmental Engineering, East China University of Science and Technology/State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, Shanghai 200237 (China); Wang, Chunyan [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Zhang, Wei [School of Resources and Environmental Engineering, East China University of Science and Technology/State Environmental Protection Key Laboratory of Environmental Risk Assessment and Control on Chemical Process, Shanghai 200237 (China); Cui, Changyuan [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Lin, Junda [Department of Biological Sciences, Florida Institute of Technology, Melbourne, FL 32901 (United States); Dong, Qiaoxiang, E-mail: dqxdong@163.com [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China); Huang, Changjiang, E-mail: cjhuang5711@163.com [Zhejiang Provincial Key Lab for Technology and Application of Model Organisms, Institute of Watershed Science and Environmental Ecology, Wenzhou Medical College, Wenzhou 325035 (China)

2011-12-15

Highlights: Black-Right-Pointing-Pointer We examined PBDE concentrations in various matrices from different industrial areas. Black-Right-Pointing-Pointer Elevated PBDE levels were found in areas with low-voltage electrical manufactures. Black-Right-Pointing-Pointer Areas with e-waste recycling activities also had higher PBDE concentrations. Black-Right-Pointing-Pointer PBDE content and composition in water samples varied from one area to another. Black-Right-Pointing-Pointer PBDE composition in sediment/soil and biological samples was predominated by BDE-209. - Abstract: Polybrominated diphenyl ethers (PBDEs) have been used extensively in electrical and electronic products, but little is known about their distribution in the environment surrounding the manufacturing factories. This study reports PBDE contamination in various matrices from the location (Liushi, Zhejiang province) that produces more than 70% of the low-voltage electrical appliances in China. Additionally, PBDE contamination was compared with other industries such as the e-waste recycling business (Fengjiang) in the same region. Specifically, we measured seven PBDE congeners (BDEs - 47, 99, 100, 153, 154, 183, and 209) in water, sediment, soil, plant, and animal tissues from four different areas in this region. The present study revealed elevated PBDE concentrations in all matrices collected from Liushi and Fengjiang in comparison with highly industrialized areas without significant PBDE contamination sources. In water samples, there were large variations of PBDE content and composition across different areas. In sediment/soil and biological samples, BDE-209 was the predominant congener and this could be due to the abundant usage of deca-BDE mixtures in China. Our findings provide the very first data on PBDE contamination in the local environments surrounding the electronics industry, and also reveal widespread PBDE contamination in highly industrialized coastal regions of China.

Management of industrial sites and areas contaminated by radionuclides in France

International Nuclear Information System (INIS)

Oudiz, A.; Rousseau, D.

2001-01-01

The presentation involves two parts making mention on the one hand on the industrial sites management and on the other hand on contaminated areas management. In a third part, are considered the analogies and the differences susceptible of appearing in the management modes of industrial sites and areas. (N.C.)

assessment of atmospheric metal depositions in the industrial areas

African Journals Online (AJOL)

Osondu

and Ogun states house many industries which are assumed to have impacted the states. It is in ... southwest Nigeria were assessed to determine the extent of air pollution of these areas. ... of pollutants but are expensive and risks of ... Island) served as the Control site for Lagos ..... cement industry on accumulation of heavy.

A Study on regeneration cases with industrial Heritage in mining areas of Korea

Science.gov (United States)

Cho, Seungyeoun; Ji, Sangwoo; Yim, Giljae

2017-04-01

The mining areas have to face urban decline problem in population and aging after its closing. Many mines were shut down due to changes in industrial structure through 20 century. Central and local governments has been trying to solve urban decline of abandoned mine areas by enacting special acts or introducing support programs for decades. In the year of 1995, South Korean government also enacted "Special act on the assistance to the development of abandoned mine areas" to promote the economy of abandoned mine areas that is depressed following the decline of the coal industry and to help balanced regional development and to improve the living standard of the residents in such abandoned mine areas. Local authorities has been trying to revitalize the regional economy by attracting tourism industry under the financial support and deregulation by this special law. With this background, this study analysis 13 regeneration cases which are utilizing the industrial heritage of the abandoned area in S. Korea. Despite the importance of mining, negative images of abandon mine have been engraved due to environmental destruction. Most of abandoned mines were left without any action since its closing. Early stage of abandoned mine area regeneration, such as Sabuk, Munkyong, are focusing on adjacent land not on abandoned mine. Abandoned mines were restored its original state and theme park including hotels, casinos and other tourist facilities were developed on adjacent land. Eco-trails on some granite caves such as Jungsun were opened to the public as natural resources not industrial heritage. The industrial heritage was very restricted to making museums about history of mining industry. However, there has been a significant change in perception toward reusing industrial heritage for urban regeneration in recent years. From the viewpoint of urban regeneration, abandon mine areas and its facilities are receiving attention as important regional assets as industrial heritage to

[Reflection on developing bio-energy industry of large oil company].

Science.gov (United States)

Sun, Haiyang; Su, Haijia; Tan, Tianwei; Liu, Shumin; Wang, Hui

2013-03-01

China's energy supply becomes more serious nowadays and the development of bio-energy becomes a major trend. Large oil companies have superb technology, rich experience and outstanding talent, as well as better sales channels for energy products, which can make full use of their own advantages to achieve the efficient complementary of exist energy and bio-energy. Therefore, large oil companies have the advantages of developing bio-energy. Bio-energy development in China is in the initial stage. There exist some problems such as available land, raw material supply, conversion technologies and policy guarantee, which restrict bio-energy from industrialized development. According to the above key issues, this article proposes suggestions and methods, such as planting energy plant in the marginal barren land to guarantee the supply of bio-energy raw materials, cultivation of professional personnel, building market for bio-energy counting on large oil companies' rich experience and market resources about oil industry, etc, aimed to speed up the industrialized process of bio-energy development in China.

EU energy policies achievement by industries in decentralized areas

Science.gov (United States)

Destro, Nicola; Stoppato, Anna; Benato, Alberto; Schiro, Fabio

2017-11-01

Energy Roadmap outlined by the European Commission sets out several routes for a more sustainable, competitive and secure energy system in 2050. All the outlined scenarios consider energy efficiency, renewable energy, nuclear energy and carbon capture and storage. In this paper, more attention has been devoted to the energy efficiency issue, by the identification of new micro and small networks opportunity fed by hybrid plants in the North-East of Italy. National energy balance and national transmission system operator data allowed to collect industrial energy consumptions data on the investigated area. Applying industrial statistics to the local energy needs allows to collect a dataset including consumption information by factory and by company structure (size and employees) for each industrial sector highlighting the factory density in the area. Preliminary outcomes from the model address to the exploitation of local by-product for energy purposes.

A multi-attribute Systemic Risk Index for comparing and prioritizing chemical industrial areas

International Nuclear Information System (INIS)

Reniers, G.L.L.; Sörensen, K.; Dullaert, W.

2012-01-01

Measures taken to decrease interdependent risks within chemical industrial areas should be based on quantitative data from a holistic (cluster-based) point of view. Therefore, this paper examines the typology of networks representing industrial areas to formulate recommendations to more effectively protect a chemical cluster against existing systemic risks. Chemical industrial areas are modeled as two distinct complex networks and are prioritized by computing two sub-indices with respect to existing systemic safety and security risks (using Domino Danger Units) and supply chain risks (using units from an ordinal expert scale). Subsequently, a Systemic Risk Index for the industrial area is determined employing the Borda algorithm, whereby the systemic risk index considers both a safety and security network risk index and a supply chain network risk index. The developed method allows decreasing systemic risks within chemical industrial areas from a holistic (inter-organizational and/or inter-cluster) perspective. An illustrative example is given.

Exporting Australia's remote area power supply industry

International Nuclear Information System (INIS)

Presnell, K.

2001-01-01

The Australian renewable energy industry has two faces: Remote Area Power Supply systems (RAPS), where the trade-off is between the traditional diesel generator and diesel hybrid or the stand alone renewable energy system. The competency of the Australian RAPS industry is recognised internationally. Grid connected renewable energy technologies, where industry activity is expanding rapidly, but where Australian competencies carry relatively little weight internationally (other than for research and development of related components such as big performance, crystalline silicon photovoltaic cells). Individual industry development strategies are required in each instance. The focus of this paper is on strategies that enhance the export potential of the Australian RAPS industry. Involvement of the electricity supply utilities is promoted as a means of quickly instituting a substantial industry presence. The term RAPS can be confusing. It is used to describe any supply system serving a remote user, be they a single property owner with a simple, stand alone DC photovoltaic supply, or several communities with complex, inter-connected, diesel/hybrid power stations, sometimes termed a 'remote-grid'. Utility interest tends to emerge as market fragmentation decreases, system complexity increases and economies of scale become evident. A review of the domestic situation is a necessary adjunct to development of export strategies for Australian RAPS products. The two are inexorably linked, as is reflected in the format of this paper. (author)

Large-area functionalized CVD graphene for work function matched transparent electrodes

Science.gov (United States)

Bointon, Thomas H.; Jones, Gareth F.; de Sanctis, Adolfo; Hill-Pearce, Ruth; Craciun, Monica F.; Russo, Saverio

2015-11-01

The efficiency of flexible photovoltaic and organic light emitting devices is heavily dependent on the availability of flexible and transparent conductors with at least a similar workfunction to that of Indium Tin Oxide. Here we present the first study of the work function of large area (up to 9 cm2) FeCl3 intercalated graphene grown by chemical vapour deposition on Nickel, and demonstrate values as large as 5.1 eV. Upon intercalation, a charge density per graphene layer of 5 ṡ 1013 ± 5 ṡ 1012 cm-2 is attained, making this material an attractive platform for the study of plasmonic excitations in the infrared wavelength spectrum of interest to the telecommunication industry. Finally, we demonstrate the potential of this material for flexible electronics in a transparent circuit on a polyethylene naphthalate substrate.

Study on waste waters of metal finishing industries around Lahore metropolitan area

International Nuclear Information System (INIS)

Khan, Izhar-ul-Haq; Mahmood, F.; Tufail, S.; Naeem, M.

2002-01-01

Study was undertaken on the waste water samples from metal finishing industries of Lahore metropolitan area for the evaluation of metallic impurities. The metal finishing industry was classified into three categories i. e. medium scale, small scale and cottage scale industry. About 93 wastewater samples were collected from various metal finishing industries around Lahore metropolitan area. In addition to toxic elements like cadmium, nickel and zinc the other parameters such as hydrogen ion concentration (pH), Electrical conductivity (EC) and Total Dissolved Salts (TDS) were also determined. (author)

Cross-industry Collaborations in the Convergence Area of Functional Foods

NARCIS (Netherlands)

Bornkessel, S.; Broring, Stefanie; Omta, S.W.F.

2016-01-01

Convergence processes are based on the activity of distinct industry sectors showing crossindustry
collaborations. The aim of this paper is to analyze cross-industry collaborations between
the food and pharmaceutical sectors in the convergence area of functional foods. Selected
companies

EU energy policies achievement by industries in decentralized areas

Directory of Open Access Journals (Sweden)

Destro Nicola

2017-01-01

Full Text Available Energy Roadmap outlined by the European Commission sets out several routes for a more sustainable, competitive and secure energy system in 2050. All the outlined scenarios consider energy efficiency, renewable energy, nuclear energy and carbon capture and storage. In this paper, more attention has been devoted to the energy efficiency issue, by the identification of new micro and small networks opportunity fed by hybrid plants in the North-East of Italy. National energy balance and national transmission system operator data allowed to collect industrial energy consumptions data on the investigated area. Applying industrial statistics to the local energy needs allows to collect a dataset including consumption information by factory and by company structure (size and employees for each industrial sector highlighting the factory density in the area. Preliminary outcomes from the model address to the exploitation of local by-product for energy purposes.

The ARIPAR project: analysis of the major accident risks connected with industrial and transportation activities in the Ravenna area

International Nuclear Information System (INIS)

Egidi, Demetrio; Foraboschi, Franco P.; Spadoni, Gigliola; Amendola, Aniello

1995-01-01

The paper describes the ARIPAR project aimed at the assessment of the major accident risks connected with storage, process and transportation of dangerous substances in the densely populated Ravenna area in Italy, which includes a large complex of chemical and petrochemical plants and minor industries, essentially distributed around an important commercial port. Large quantities of dangerous goods are involved in various transportation forms connected with the industrial and commercial activity of the port. The project started by making a complete inventory of fixed installations and transportation activities capable of provoking major fire, explosion and toxic release events; then relevant accident scenarios were developed for the single hazard sources; probabilities were assigned to the events and consequences were evaluated; finally iso-risk contours and F-N diagrams were evaluated both for the single sources and for the overall area. This required the development of a particular methodology for analysis of area risk and of associated software packages which allowed examination of the relative importance of the different activities and typologies of materials involved. The methodological approach and the results have proved to be very useful for the priority-ranking of risk mitigating interventions and physical planning in a complex area

Composition of airborne particulate matter in the industrial area versus mountain area

Directory of Open Access Journals (Sweden)

Barbora Sýkorová

2016-03-01

Full Text Available The paper deals with research of air pollution in two different locations on the Moravian-Silesian Region, Czech Republic. These are the sites Ostrava-Radvanice, which is located in the area affected by the industry and Ostravice in the mountains (without significant effect of the industry. The dust particles collected at these locations were subjected to a wide range of analyses. The mass concentration, the mass-size distribution, mineralogical composition, the concentration of PAHs (polycyclic aromatic hydrocarbons, and the concentrations of selected metals (Cd, Pb, Zn, Fe, Mn, As, Ni, Co, and Cr were observed at the particulate matter.

High-Rate Fabrication of a-Si-Based Thin-Film Solar Cells Using Large-Area VHF PECVD Processes

Energy Technology Data Exchange (ETDEWEB)

Deng, Xunming [University of Toledo; Fan, Qi Hua

2011-12-31

The University of Toledo (UT), working in concert with it’s a-Si-based PV industry partner Xunlight Corporation (Xunlight), has conducted a comprehensive study to develop a large-area (3ft x 3ft) VHF PECVD system for high rate uniform fabrication of silicon absorber layers, and the large-area VHF PECVD processes to achieve high performance a-Si/a-SiGe or a-Si/nc-Si tandem junction solar cells during the period of July 1, 2008 to Dec. 31, 2011, under DOE Award No. DE-FG36-08GO18073. The project had two primary goals: (i) to develop and improve a large area (3 ft × 3 ft) VHF PECVD system for high rate fabrication of > = 8 Å/s a-Si and >= 20 Å/s nc-Si or 4 Å/s a-SiGe absorber layers with high uniformity in film thicknesses and in material structures. (ii) to develop and optimize the large-area VHF PECVD processes to achieve high-performance a-Si/nc-Si or a-Si/a-SiGe tandem-junction solar cells with >= 10% stable efficiency. Our work has met the goals and is summarized in “Accomplishments versus goals and objectives”.

An industrial perspective on bioreactor scale-down: what we can learn from combined large-scale bioprocess and model fluid studies.

Science.gov (United States)

Noorman, Henk

2011-08-01

For industrial bioreactor design, operation, control and optimization, the scale-down approach is often advocated to efficiently generate data on a small scale, and effectively apply suggested improvements to the industrial scale. In all cases it is important to ensure that the scale-down conditions are representative of the real large-scale bioprocess. Progress is hampered by limited detailed and local information from large-scale bioprocesses. Complementary to real fermentation studies, physical aspects of model fluids such as air-water in large bioreactors provide useful information with limited effort and cost. Still, in industrial practice, investments of time, capital and resources often prohibit systematic work, although, in the end, savings obtained in this way are trivial compared to the expenses that result from real process disturbances, batch failures, and non-flyers with loss of business opportunity. Here we try to highlight what can be learned from real large-scale bioprocess in combination with model fluid studies, and to provide suitable computation tools to overcome data restrictions. Focus is on a specific well-documented case for a 30-m(3) bioreactor. Areas for further research from an industrial perspective are also indicated. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Guidelines for planning interventions against external exposure in industrial area after a nuclear accident. Pt. 1. A holistic approach of countermeasure application

International Nuclear Information System (INIS)

Eged, K.; Kis, Z.; Andersson, K.G.; Roed, J.; Varga, K.

2003-01-01

Following a large-scale release of radioactivity into the environment, different urban, industrial and rural environments may be contaminated for many years. Currently, there is limited systematic consideration of long-term management to ensure sustainability of areas contaminated by long-lived radionuclides. To sustain acceptable living and working conditions in such areas it is important to be able to construct robust, effective restoration strategies which address the many different types of environment, land use and ways of life. The overall objective of the STRATEGY project (directly addressing Key Action 2: Nuclear Fission - Off-site emergency management in the Fifth Framework Programme) is to establish a decision framework to enable the selection of robust and practicable remediation strategies for Member States, which enable the long-term sustainable management of contaminated areas. The special objectives of the work carried out by GSF - Radiation Protection Institute and presented in this report was to contribute to the different urban/industrial parts of the STRATEGY project. Countermeasures being different from the usual urban ones and largely applicable in industrial area are collected and evaluated. The industrial area is defined here as such an area where productive and/or commercial activity is carried out. A good example is a supermarket or a factory. In designing restoration strategies to ensure the long-term sustainability of large and varied contaminated areas, there is a requirement to adopt a more holistic approach rather than simply selecting cost-effective countermeasures. The potentially negative consequences of restoration must be fully considered. The implementation of a remediation strategy may lead to a reduced collective dose, but increased dose to those implementing the strategies. Countermeasures may themselves generate waste and the practical consideration of disposal options has to be addressed. There is also a requirement that the

Large-area OLED lightings and their applications

International Nuclear Information System (INIS)

Park, J W; Shin, D C; Park, S H

2011-01-01

In this paper, we review the key issues related to the fabrication of large-area organic light-emitting devices (OLEDs) for lighting applications. We discuss the origin of a short-circuit problem, luminance non-uniformity, hot spot, efficiency reduction (power loss), and heat generation and present the way of suppressing them. We also introduce three different application areas of large-area OLED lighting panels. They can be integrated with a solar cell for power recycling or inorganic LEDs for emotional lightings. The feasibility of using OLEDs for the application of visible-light communications is also reviewed

Precautionary interventions in industrial areas. An optimal stopping approach

Energy Technology Data Exchange (ETDEWEB)

Pauwels, N

2001-04-01

The contribution consists of an abstract of a PhD thesis. The thesis deals with the precautionary evacuation of an industrial facility's workforce threatened by a radiological release from a nuclear power plant nearby. The issue of deferring intervention decisions until additional information is available is addressed. Furthermore, interventions in industrial areas with a concentration of chemical and petrochemical plants form part of this study.

Precautionary interventions in industrial areas. An optimal stopping approach

International Nuclear Information System (INIS)

Pauwels, N.

2001-01-01

The contribution consists of an abstract of a PhD thesis. The thesis deals with the precautionary evacuation of an industrial facility's workforce threatened by a radiological release from a nuclear power plant nearby. The issue of deferring intervention decisions until additional information is available is addressed. Furthermore, interventions in industrial areas with a concentration of chemical and petrochemical plants form part of this study

Research Update: Large-area deposition, coating, printing, and processing techniques for the upscaling of perovskite solar cell technology

Directory of Open Access Journals (Sweden)

Stefano Razza

2016-09-01

Full Text Available To bring perovskite solar cells to the industrial world, performance must be maintained at the photovoltaic module scale. Here we present large-area manufacturing and processing options applicable to large-area cells and modules. Printing and coating techniques, such as blade coating, slot-die coating, spray coating, screen printing, inkjet printing, and gravure printing (as alternatives to spin coating, as well as vacuum or vapor based deposition and laser patterning techniques are being developed for an effective scale-up of the technology. The latter also enables the manufacture of solar modules on flexible substrates, an option beneficial for many applications and for roll-to-roll production.

MILDOS-AREA: An enhanced version of MILDOS for large-area sources

International Nuclear Information System (INIS)

Yuan, Y.C.; Wang, J.H.C.; Zielen, A.

1989-06-01

The MILDOS-AREA computer code is a modified version of the MILDOS code, which estimates the radiological impacts of airborne emissions from uranium mining and milling facilities or any other large-area source involving emissions of radioisotopes of the uranium-238 series. MILDOS-AREA is designed for execution on personal computers. The modifications incorporated in the MILDOS-AREA code provide enhanced capabilities for calculating doses from large-area sources and update dosimetry calculations. The major revision from the original MILDOS code is the treatment of atmospheric dispersion from area sources: MILDOS-AREA substitutes a finite element integration approach for the virtual-point method (the algorithm used in the original MILDOS code) when specified by the user. Other revisions include the option of using Martin-Tickvart dispersion coefficients in place of Briggs coefficients for a given source, consideration of plume reflection, and updated internal dosimetry calculations based on the most recent recommendations of the International Commission on Radiation Protection and the age-specific dose calculation methodology developed by Oak Ridge National Laboratory. This report also discusses changes in computer code structure incorporated into MILDOS-AREA, summarizes data input requirements, and provides instructions for installing and using the program on personal computers. 15 refs., 9 figs., 26 tabs

Creating new path for Old Industrial Areas: A Case Study on Dalian city, China

Directory of Open Access Journals (Sweden)

Yimei Yin and Zhigao Liu

2012-01-01

Full Text Available The formation of new industries has recently been widely studied, but little research attention has been paid to the formation of new industries in old industrial districts, especially in transitional countries such as China. Based on fieldwork and rereading historical archives, this paper uses an example of Dalian tourism cluster to contribute to understanding the emergence of new economy in old industrial areas in a transitional country. The Section 2 of this paper will provide the theoretical framework from evolutionary economics for my empirical study. In Section 3, this paper will discuss the main characteristics of the decline of old industrial areas in Northeast China and the significances of developing new economy to revitalizing old industry areas. Section 4 will introduce the transitional history of Dalian economy from a high industrial region to a new economy city and also provides descriptive information about the development process of Dalian tourism industry. In Section 5, this paper will probe into the dynamics of the Dalian tourism cluster, from viewpoints of co-evolution and co-adaptation of firm, technology and institutions. Finally, we will give some policy suggestions of how to foster and promote new industries in old industrial areas, especially for transitional countries.

The European Large Area ISO Survey

DEFF Research Database (Denmark)

Oliver, S.; Rowan-Robinson, M.; Alexander, D.M.

2000-01-01

We describe the European Large Area ISO Survey (ELAIS). ELAIS was the largest single Open Time project conducted by ISO, mapping an area of 12 deg(2) at 15 mu m with ISOCAM and at 90 mu m with ISOPHOT. Secondary surveys in other ISO bands were undertaken by the ELAIS team within the fields of the...

Bulgarian electricity market and the large-scale industrial customers

International Nuclear Information System (INIS)

Popov, P.; Kanev, K.; Dyankov, M.; Minkov, N.

2003-01-01

The paper focuses on a brief overview of the Bulgarian Electricity Market Design and steps toward its development, as well as on preliminary analyses for market opening and influence of large industrial customers to system and market operation. (author)

Characteristic of ambient airborne and respirable particulate around a non formal industrial area

International Nuclear Information System (INIS)

Muhayatun Santoso; Diah Dwiana Lestiani; Mariana Marselina; Rita Mukhtar

2016-01-01

Characterization of airborne particulate matter and respirable particulate in Parung Panjang district especially on surrounding non formal used batteries industrial area has been carried out to follow up the previous results with respect to high concentrations of lead detected in Serpong area. Sampling of airborne particulate matter in Parung Panjang was conducted using Gent stacked filter unit sampler, while the respirable particulate matter samples collected using personal dust sampler in Parung Panjang as a non formal Industrial area and Sukarasa village as a control, during 2011-2012. The concentration of masses were determined gravimetrically, while for elemental concentrations by X-Ray based methods. The average of mass concentration of air ambient PM 2.5 and PM 10 in Parung Panjang were 27.3 ± 13.7 and 77.5 ± 17.1 μg.m -3 , respectively. While the average concentration of respirable particulate in non formal industrial and control areas were 260 ± 233 and 82 ± 38 μg.m -3 , respectively. The percentage of average Pb concentration in PM 2.5 and PM 2.5-10 were contribute up to 45 and 10 % of the mass concentration, respectively. The maximum percentage concentration of Pb in respirable particulate in industrial and control area were 12.11 and 0.27 %, respectively. These results showed that the Pb concentrations in respirable particulate in industrial area were significantly tens times higher than in the control area. The high concentration of Pb in Parung Panjang was the main key element came from the used lead battery industry and one of pollutant source that contributed to the Pb pollution in Serpong area. (author)

Vegetation pattern and soil characteristics of the polluted industrial area of Karachi

International Nuclear Information System (INIS)

Kabir, M.; Iqbal, M.Z.; Farooqi, M.Z.; Shafiq, M.

2010-01-01

A quantitative phyto sociological survey was conducted around the industrial areas of Sindh Industrial Trading Estate (S.I.T.E.) of Karachi. The herbaceous, shrubs vegetation was predominantly disturbed in nature. Fifteen plant communities based on Importance Value Index (IVI) of species were recognized. Eighty plant species were recorded in industrial areas. Abutilon fruticosum L., attained the highest importance value index (823.25) followed by Prosopis juliflora DC. (662.62), Corchorus trilocularis L. (467.20), Aerva javanica Burm.f. (419.97), Amaranthus viridis L. (397.65) and Senna holosericea L. (387.22), respectively. P. juliflora and A. fruticosum showed leading first dominant in five and four stands, respectively. Whereas, A. javanica, A. viridis, S. holosericea, Launaea nudicaulis L., Crochorus depressus L. and Salvadora L., attained the presence class III. Zygophyllum simplex L., Suaeda fruticosa L., Convolvulus glomeratus Choisky, Cressa cretica L., Cleome viscosa L., Calotropis procera Willd, Blepharis sindica T. Anderson, Rhynchosia pulverulenta L., Abutilon pakistanicum Jafri and Ali, Chenopodium album L., Capparis decidua Forssk and Digera muricata L. Mart showed the presence of class II. Whereas, rest of 58 species showed presence of class I. The soil characteristics of the polluted industrial area were also analyzed and related with the vegetation of the polluted areas. The Industrial area soil was coarse in texture and ranged from sandy clay loam to sandy loam. The soil was acidic to alkaline in nature. Maximum water holding capacity, bulk density, porosity, CaCO/sub 3/, pH, organic matter, total organic carbon, chloride, electrical conductivity, total dissolved salt, available sulphur contents, exchangeable sodium and potassium were recorded in wide range. It was concluded that certain edaphic factors due to industrial activities and induction of pollutants were responsible for variation in vegetation composition of the study area. (author)

Guidelines for planning interventions against external exposure in industrial area after a nuclear accident. Pt. 2. Calculation of doses using Monte Carlo method

International Nuclear Information System (INIS)

Kis, Z.; Eged, K.; Meckbach, R.; Mueller, H.

2003-01-01

Countermeasures being different from the usual urban ones and largely applicable in industrial area are collected and evaluated in a separate report. The industrial area is defined here as such an area where productive and/or commercial activity is carried out. A good example is a supermarket or a factory. Based on the history of calculation models it is unambiguous that the Monte Carlo based simulation is the perspective to the dose assessment from external exposures in such a complex environment. A method of the calculation of doses from external exposures in urban-industrial environment is presented. Moreover, this report gives a summary about the time dependence of the source strengths relative to a reference surface and a short overview about the mechanical and chemical intervention techniques which can be applied in this area. Using a hypothetical scenario (a supermarket area contaminated by 137 Cs) the details of an exemplary calculation are given directly addressing the dose and averted dose blocks of the templates of industrial countermeasures. In addition, a sensitivity analysis of the results is presented. (orig.)

Analysis of phthalate esters in soils near an electronics manufacturing facility and from a non-industrialized area by gas purge microsyringe extraction and gas chromatography

Energy Technology Data Exchange (ETDEWEB)

Wu, Wei [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China); Hu, Jia [Suzhou Center for Disease Prevention and Control, Suzhou, Jiangsu (China); Wang, Jinqi; Chen, Xuerong; Yao, Na [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China); Tao, Jing, E-mail: jingtao1982@126.com [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China); Zhou, Yi-Kai, E-mail: zhouyk@mails.tjmu.edu.cn [MOE Key Laboratory of Environment and Health, Institute of Environmental Medicine, School of Public Health, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, Hubei (China)

2015-03-01

Here, a novel technique is described for the extraction and quantitative determination of six phthalate esters (PAEs) from soils by gas purge microsyringe extraction and gas chromatography. Recovery of PAEs ranged from 81.4% to 120.3%, and the relative standard deviation (n = 6) ranged from 5.3% to 10.5%. Soil samples were collected from roadsides, farmlands, residential areas, and non-cultivated areas in a non-industrialized region, and from the same land-use types within 1 km of an electronics manufacturing facility (n = 142). Total PAEs varied from 2.21 to 157.62 mg kg{sup −1} in non-industrialized areas and from 8.63 to 171.64 mg kg{sup −1} in the electronics manufacturing area. PAE concentrations in the non-industrialized area were highest in farmland, followed (in decreasing order) by roadsides, residential areas, and non-cultivated soil. In the electronics manufacturing area, PAE concentrations were highest in roadside soils, followed by residential areas, farmland, and non-cultivated soils. Concentrations of dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP) differed significantly (P < 0.01) between the industrial and non-industrialized areas. Principal component analysis indicated that the strongest explanatory factor was related to DMP and DnBP in non-industrialized soils and to butyl benzyl phthalate (BBP) and DMP in soils near the electronics manufacturing facility. Congener-specific analysis confirmed that diethylhexyl phthalate (DEHP) was a predictive indication both in the non-industrialized area (r{sup 2} = 0.944, P < 0.01) and the industrialized area (r{sup 2} = 0.860, P < 0.01). The higher PAE contents in soils near the electronics manufacturing facility are of concern, considering the large quantities of electronic wastes generated with ongoing industrialization. - Highlights: • A new method for determining phthalate esters in soil samples was developed. • Investigate six phthalates near an industry and a

Heavy Metal Contamination Assessment and Partition for Industrial and Mining Gathering Areas

Directory of Open Access Journals (Sweden)

Yang Guan

2014-07-01

Full Text Available Industrial and mining activities have been recognized as the major sources of soil heavy metal contamination. This study introduced an improved Nemerow index method based on the Nemerow and geo-accumulation index. Taking a typical industrial and mining gathering area in Tianjin (China as example, this study then analyzed the contamination sources as well as the ecological and integrated risks. The spatial distribution of the contamination level and ecological risk were determined using Geographic Information Systems. The results are as follows: (1 Zinc showed the highest contaminant level in the study area; the contamination levels of the other seven heavy metals assessed were relatively lower. (2 The combustion of fossil fuels and emissions from industrial and mining activities were the main sources of contamination in the study area. (3 The overall contamination level of heavy metals in the study area ranged from heavily contaminated to extremely contaminated and showed an uneven distribution. (4 The potential ecological risk showed an uneven distribution, and the overall ecological risk level ranged from low to moderate. This study also emphasized the importance of partition in industrial and mining areas, the extensive application of spatial analysis methods, and the consideration of human health risks in future studies.

Heavy Metal Contamination Assessment and Partition for Industrial and Mining Gathering Areas

Science.gov (United States)

Guan, Yang; Shao, Chaofeng; Ju, Meiting

2014-01-01

Industrial and mining activities have been recognized as the major sources of soil heavy metal contamination. This study introduced an improved Nemerow index method based on the Nemerow and geo-accumulation index. Taking a typical industrial and mining gathering area in Tianjin (China) as example, this study then analyzed the contamination sources as well as the ecological and integrated risks. The spatial distribution of the contamination level and ecological risk were determined using Geographic Information Systems. The results are as follows: (1) Zinc showed the highest contaminant level in the study area; the contamination levels of the other seven heavy metals assessed were relatively lower. (2) The combustion of fossil fuels and emissions from industrial and mining activities were the main sources of contamination in the study area. (3) The overall contamination level of heavy metals in the study area ranged from heavily contaminated to extremely contaminated and showed an uneven distribution. (4) The potential ecological risk showed an uneven distribution, and the overall ecological risk level ranged from low to moderate. This study also emphasized the importance of partition in industrial and mining areas, the extensive application of spatial analysis methods, and the consideration of human health risks in future studies. PMID:25032743

Flared gases and other pollutants associated with air quality in industrial areas of Nigeria: an overview.

Science.gov (United States)

Osuji, Leo C; Avwiri, Greg O

2005-10-01

Nigeria, like any other developing nation, is faced with the twin problem of development without destruction. Industrialization, though an important component of development, has had a large share in the despoilation of air quality in the country by the release of high amounts of pollutants into the atmosphere. Petroleum hydrocarbons from refineries, flared gases, dusts, and fumes of metal-smelting and cement works, odorous gases of chemical and allied industries, carbon monoxide and oxides of sulfur and nitrogen of internal combustion engines, the charred particulates and sulfur dioxide emissions of the steel industries etc., all constitute pollutants or co-pollutants of the Nigerian atmosphere. This review article gives an insight into the phenomenal concentrations of some of these pollutants in the Nigerian atmosphere, which point to their unsafe levels and concomitant health risks. It is against this background that there should be continuous but sound monitoring exercise of the Nigerian environment, devoid of the peculiar mix of politics and science, in order to properly audit the quality of air, especially in areas of heavy industrial pollution. Such checks and balances would provide empirical data to assess the various trade-offs of atmospheric pollution in industrial areas of the country such as the Niger Delta region where oil and gas are produced. There should also be enforcement, thereof, of all existing and/or revised standards or regulations such as the compliance limits of the Department of Petroleum Resources (DPR) or the erstwhile Federal Environmental Protection Agency (FEPA).

A study of polluted eco-system around industrial areas

International Nuclear Information System (INIS)

Husaini, S.N.; Khan, E.U.; Qureshi, I.E.; Malik, F.; Zaidi, J.H.; Arif, M.; Fatima, I.; Arif, M.

2005-01-01

Industrial pollution is one of the most serious problems in Pakistan. The uncontrolled release of untreated industrial effluents to large water bodies has deleterious effects on water quality, aquatic life and human health. The concentration of heavy metals in eco-system is reaching at alarming levels and is increasing yearly. In reality, the industries are not equipped with proper effluent treatment plants. The environmental protection law is not strictly implemented to limit the release and/or proper disposal of industrial effluents. Therefore, volume of specified industrial discharge is growing at an exponential rate without any specific safeguards. Effective measures, which can eliminate or considerably reduce hazardous factors from the human environment to minimize the associated health risks, must be identified and eradicated. In order to achieve these objectives, the study has been done to reach a balanced assessment of the risks and benefits involved. For this purpose two industrial cities of Pakistan namely, Gujranwala and Faisalabad have been selected. Four major industries existing in these cities, namely Yam, textile, paper and board and ceramics, have been studied. The specimens of the irrigated soil exposed to the industrial effluent, crops and vegetables grown on that soil have been analyzed study the hazardous effects on human health. (author)

Manufacture of axially insulated large-area diodes

International Nuclear Information System (INIS)

Ma Weiyi; Zhou Kungang; Wang Youtian; Zhang Dong; Shan Yusheng; Wang Naiyan

1999-01-01

The author describes the design and construction of the axially insulated large-area diodes used in the 'Heaven-1'. The four axially insulated large-area diodes are connected to the 10 ohm pulse transmission lines via the vacuum feed through tubes. The experimental results with the diodes are given. The diodes can steadily work at the voltage of 650 kV, and the diode current density is about 80 A per cm 2 with a pulse width of 220 ns. The electron beams with a total energy of 25 kJ are obtained

Noise Pulses in Large Area Optical Modules

International Nuclear Information System (INIS)

Aiello, Sebastiano; Leonora, Emanuele; Giordano, Valentina

2013-06-01

A great number of large area photomultipliers are widely used in neutrino and astro-particle detector to measure Cherenkov light in medium like water or ice. The key element of these detectors are the so-called 'optical module', which consist in photodetectors closed in a transparent pressure-resistant container to protect it and ensure good light transmission. The noise pulses present on the anode of each photomultiplier affect strongly the performance of the detector. A large study was conducted on noise pulses of large area photomultipliers, considering time and charge distributions of dark pulses, prepulses, delayed pulses, and after pulses. The contribution to noise pulses due to the presence of the external glass spheres was also studied, even comparing two vessels of different brands. (authors)

Wind energy in industrial areas. Results of an attitude survey

International Nuclear Information System (INIS)

Schoolderman, J.A.; Huiberts, R.G.J.

2000-06-01

The feasibility of installing wind turbines in industrial parks in the Netherlands has been investigated. An overview is given of possibilities and constraints to fit in wind turbines in industrial areas, based on the results of a literature study, a market consultation of sectoral organizations, representatives of local industrial circles and industrial experts in the field of renewable energy. Also a telephone survey was carried out among 130 entrepreneurs in the Netherlands to determine their attitudes towards the use of sustainable energy and wind energy in industrial parks. The results of the attitude study are published in this report. The main report is a separate report for which a separate abstract has been prepared. The intermediate results were discussed at a meeting (23 February 2000), in which representatives from the industry, provinces, municipalities and the government participated

Preserving Medieval Farm Mounds in a Large Stormwater Retention Area

NARCIS (Netherlands)

Vorenhout, M.

2016-01-01

The Netherlands has denoted large areas as stormwater retention areas. These areas function as temporary storage locations for stormwater when rivers cannot cope with the amount of water. A large area, the Onlanden — 2,500 hectares — was developed as such a storage area between 2008 and 2013. This

Radiological protection in the industrial area

International Nuclear Information System (INIS)

Fraga, H.

2008-12-01

Radiation protection (RP) in industrial applications is composed of four major themes that are recruiting and training personnel, equipment and instrumentation, materials used and also the acquisition of new technologies to improve their own RP. To carry out the recruitment of staff and train them to serve as occupationally exposed personnel in the industry continues with the Mexican Official Standard NOM-031-NUCL-1999, R equirements for qualification and training of personnel occupationally exposed to radiation ionizing , what will be done regarding the physical fitness of personnel by NOM-026-NUCL-1999, M edical surveillance of personnel occupationally exposed to ionizing radiation . The principle of optimization of the RP, or ALARA principle (keeping the risk as low as reasonably achievable), is assumed to be the safety philosophy in the field of industrial applications of ionizing radiation. Practically all the elements that make up the equipment, instrumentation and materials used in industrial radiography and other industrial applications, has an orientation towards the protection, along with procedures that operate. For example, in industrial radiography the technician always has several instruments for radiation detection and measurement, some with visible and audible alarms. The equipment characteristics and transport (containers) are regulated by the standards NOM-025/1- 2000 and NOM-025/2-2996, which contains requirements for radiological safety in design and operation, respectively, for both as containers for some of its parts and accessories. As part of the technological innovation with benefits to the RP itself and eventually target practice today are venturing into the radiography digital, which involves the exposure of a plate image phosphorus-based with the later download to a computer. In combination with the use of sources of X-rays, there is a real contribution to reducing the dose, since the later are nowadays equipped with programmable

Large-Area Neutron Detector based on Li-6 Pulse Mode Ionization Chamber

International Nuclear Information System (INIS)

Chung, K.; Ianakiev, K.D.; Swinhoe, M.T.; Makela, M.F.

2005-01-01

Prototypes of a Li-6 Pulse Mode Ionization Chamber (LiPMIC) have been in development for the past two years for the purpose of providing large-area neutron detector. this system would be suitable for remote deployment for homeland security and counterterrorism needs at borders, ports, and nuclear facilities. A prototype of LiPMIC is expected to provide a similar level of performance to the current industry-standard, He-3 proportional counters, while keeping the initial cost of procurement down by an order of magnitude, especially where large numbers of detectors are required. The overall design aspect and the efficiency optimization process is discussed. Specifically, the MCNP simulations of a single-cell prototype were performed and benchmarked with the experimental results. MCNP simulations of a three dimensional array design show intrinsic efficiency comparable to that of an array of He-3 proportional counters. LiPMIC has shown steady progress toward fulfilling the design expectations and future design modification and optimization are discussed.

Environmental and Socio-economic Aspects of the Operation of Industrial Regions: The Case Study of the Industrial Area of Alexandroupolis (Greece)

International Nuclear Information System (INIS)

Theofanoudi, Aglaia; Diakaki, Christina; Katsivela, Eleftheria

2009-01-01

The paper summarizes the results of a study concerning the operation of industrial plants and their effects to the environment. It also addresses, shortly, the consequences to the quality of human life and proposes potential measures that may contribute to the reduction of the negative environmental impacts. The relatively small organized Industrial Area of Alexandroupolis (Greece) is examined as a case study. In particular, the activities of its major industrial facilities are presented and their emissions to the environment are examined. In addition, the socio-economic aspects of the operation of the Industrial Area are studied. The results of the study showed that the operation of the Industrial Area has specific negative effects in the natural environment of the region and in the quality of life of the residents. Methodological and legislative tools, such as control systems for the environmental pollution, the green chemistry, and the environmental management systems, may be employed to assist the prevention and confrontation of environmental problems

Mapping the electrical properties of large-area graphene

DEFF Research Database (Denmark)

Bøggild, Peter; Mackenzie, David; Whelan, Patrick Rebsdorf

2017-01-01

The significant progress in terms of fabricating large-area graphene films for transparent electrodes, barriers, electronics, telecommunication and other applications has not yet been accompanied by efficient methods for characterizing the electrical properties of large-area graphene. While......, and a high measurement effort per device. In this topical review, we provide a comprehensive overview of the issues that need to be addressed by any large-area characterisation method for electrical key performance indicators, with emphasis on electrical uniformity and on how this can be used to provide...... a more accurate analysis of the graphene film. We review and compare three different, but complementary approaches that rely either on fixed contacts (dry laser lithography), movable contacts (micro four point probes) and non-contact (terahertz time-domain spectroscopy) between the probe and the graphene...

The Haendeloe area in Norrkoeping, Sweden: Does it fit for Industrial Symbiosis development?

Energy Technology Data Exchange (ETDEWEB)

Hatefipour, Saeid; Baas, Leenard; Eklund, Mats (Div. of Environmental Technology and Management - Dept. of Management and Engineering, Linkoeping Univ., Linkoeping (Sweden)), e-mail: saeid.hatefipour@liu.se

2011-06-15

Today, sustainable cities/regions are playing an important role in sustainable development projects. The overall aim of the current paper is to demonstrate an Industrial Symbiosis development in the Haendeloe area of Norrkoeping city in the Oestergoetland county of Sweden. It is part of a research program called 'Sustainable Norrkoeping' focusing on developing links between the industrial and the urban part of the city. As analysis of the current situation is important for understanding the future development, the paper tries to map the current industrial symbiosis links and symbiotic network to identify potentials exist. To achieve this, paper gives a general view of how this area has been developed, constructed, and grown. The next stage is devoted to an inventory of different actors, stakeholders, and companies, their processes and relationships in the form of energy, materials and by-products exchanges, flows and streams into and out of the Haendeloe area considering the Haendeloe/Norrkoeping as system boundaries. In addition, by describing different tools, elements and approaches of industrial symbiosis and considering and applying two main key tools as industrial inventories and input/output matching the paper also tries to show that whether the already industrial activities formed inside the Haendeloe fits for an industrial symbiosis development

Coating and Patterning Functional Materials for Large Area Electrofluidic Arrays

Directory of Open Access Journals (Sweden)

Hao Wu

2016-08-01

Full Text Available Industrialization of electrofluidic devices requires both high performance coating laminates and efficient material utilization on large area substrates. Here we show that screen printing can be effectively used to provide homogeneous pin-hole free patterned amorphous fluoropolymer dielectric layers to provide both the insulating and fluidic reversibility required for devices. Subsequently, we over-coat photoresist using slit coating on this normally extremely hydrophobic layer. In this way, we are able to pattern the photoresist by conventional lithography to provide the chemical contrast required for liquids dosing by self-assembly and highly-reversible electrofluidic switching. Materials, interfacial chemistry, and processing all contribute to the provision of the required engineered substrate properties. Coating homogeneity as characterized by metrology and device performance data are used to validate the methodology, which is well-suited for transfer to high volume production in existing LCD cell-making facilities.

Geochemical study of urban soils in public areas of an industrialized town (Ajka, western Hungary)

Science.gov (United States)

Zacháry, D.; Jordán, Gy.; Szabó, Cs.

2012-04-01

Soil is one of the most essential parts of urban ecosystem contributing to the biogeochemical cycles along the rock-soil-plant-animal and human pathway. Soil plays a fundamental role in plant nutrient uptake and groundwater filtration, too. Urban soils differ from non-urban soils in many aspects, including their origin, and they may also concentrate contaminants in large quantities due to intensive human activities. The pollution sources are industry, traffic, fertilizer, tailing and waste. In addition to the increasing rate of urban areas, urban soils are under growing interest and their pollution have received significant attention in the past few decades. This work focuses on the toxic element (As, Hg, Pb, Cu, Zn, Cd, Ni) content of soils and their spatial distribution in order to find a link between contamination sources and the receiving urban soils at sensitive receptor locations such as children's playgrounds and parks. Ajka town is located in western Hungary. It has an old-established industrial history with multiple contamination sources of heavy alumina industry and coal-based power plants supplied by the nearby bauxite and coal mines. At 44 locations 46 soil samples have been collected at a depth of 0-10 cm along a 1x1 km grid. The whole grid covers an area of 48 km2. In each grid cell a sampling site was selected at public areas. Sample preparation included drying at 40 C°, thorough homogenization and sieving to 2 mm fine earth before chemical analysis. Grain size distribution and soil pH were also determined. Samples were analyzed with ICP-OES and SEM methods. The As, Hg, Pb, Cu, Zn, Cd and Ni concentrations range from 2.07 ppm to 9.48 ppm, 0.02 ppm to 2.84 ppm, 5.08 ppm to 35.74 ppm, 2.55 ppm to 47.78 ppm, 17.00 ppm to 91.00 ppm, 0.07 ppm to 0.61 ppm and 5.57 ppm to 32.09 ppm, respectively. The results revealed the contaminated areas associated with past industrial sites. This study also identified locations with considerable contamination at

ALTERNATIVE SOURCE APPORTIONMENT IN THE SURROUNDING REGION OF A LARGE STEEL INDUSTRY APPLYING Tillandsia usneoides AS BIOMONITOR

Directory of Open Access Journals (Sweden)

Laura Benevides dos Santos

Full Text Available From the beginning of its operation, this large steel industrial complex in the Santa Cruz Industrial District, Rio de Janeiro, Brazil, with an annual capacity of 5 million tons, has been at the center of controversy related to its atmospheric emissions. Since the air filter used for its routine air particulate monitoring network is not appropriate for a source apportionment study, biomonitoring was tested as an alternative way to carry out this evaluation. Thus, the bromeliad species Tillandsia usneoides was used as a bioindicator in the Santa Cruz Industrial District, Rio de Janeiro, Brazil. Six samplings were performed over a period of approximately one year. The results showed that the sampling point located inside the industrial complex presented higher elemental concentration values for all samples. Among the quantifiable elements found in the biomonitor samples, iron seems to be the element that best represents the emissions from the steelwork complex, which was corroborated based on the analysis of dust jar samples collected inside the complex area.

Assessment of the Impact of Industrial Effluents on Groundwater Quality in Okhla Industrial Area, New Delhi, India

Directory of Open Access Journals (Sweden)

Wequar Ahmad Siddiqui

2009-01-01

Full Text Available In the present study physicochemical parameters like pH, hardness, TDS, chloride, sulphate, nitrate, fluoride, DO, COD and conductivity of some important heavy metals such as iron, cobalt, cadmium, lead, mercury, chromium, selenium and arsenic were first analyzed in effluent water of Okhla industrial area phase-II and then groundwater of near by areas. Obtained values of effluent water were compared with ISI standard for effluent water discharge and groundwater values were compared with ISI and WHO drinking water standards. The result shows that discharge of untreated effluents by the industries is leading to contamination of groundwater of the surrounding areas. Lead, mercury, fluoride, TDS, sulphate was above the desirable limit in effluent water (ISI standard for effluent water discharge. Subsequent analysis of groundwater of nearby areas was rated as unacceptable for drinking because of presence of fluoride in all the samples above the desirable limit. Lead, mercury, cadmium, chloride was also detected in many samples.

Progress on large area GEMs (VCI 2010)

CERN Document Server

Villa, Marco; Alfonsi, Matteo; Brock, Ian; Croci, Gabriele; David, Eric; de Oliveira, Rui; Ropelewski, Leszek; Taureg, Hans; van Stenis, Miranda

2011-01-01

The Gas Electron Multiplier (GEM) manufacturing technique has recently evolved to allow the production of large area GEMs. A novel approach based on single mask photolithography eliminates the mask alignment issue, which limits the dimensions in the traditional double mask process. Moreover, a splicing technique overcomes the limited width of the raw material. Stretching and handling issues in large area GEMs have also been addressed. Using the new improvements it was possible to build a prototype triple-GEM detector of ~ 2000 cm2 active area, aimed at an application for the TOTEM T1 upgrade. Further refinements of the single mask technique give great control over the shape of the GEM holes and the size of the rims, which can be tuned as needed. In this framework, simulation studies can help to understand the GEM behavior depending on the hole shape.

Development of large scale industrial complex and its pollution. Case study of Kashima area

Energy Technology Data Exchange (ETDEWEB)

Nagai, S

1975-01-01

The development of Kashima industrial complex which embraces three townships started in 1960 to promote both agricultural and industrial developments using the most advanced techniques available for environmental pollution control. The chronological development progress is described with reference to the capital investment, gross product, employment and labor supply, population, status of the use of agricultural land, annual revenue and expenditure of three townships, and township tax. The environmental pollution control policies and measures taken since 1964 are reviewed. The emphasis was placed on preliminary investigations by various means and emission standards were applied. However, many incidences of pollution damage occurred due to operational errors and accidental causes. The emission quantity of sulfur dioxide is to be reduced from 8212 N cu m/h in 1973 to 4625 N cu m/h in 1976.

Impact of Industrial Releases on Inshas Area

International Nuclear Information System (INIS)

El-Messiry, A.M.; Aly, M.M.

1999-01-01

Two Egyptian research reactors are located within the nuclear research center at Inshas area, 30 km north east of Cairo. This area are crowded by different industrial plants. The releases from them has a hazardous and economical effects on the research center workers and the surrounding inhabitancy. In the present work we study these effects. A meteorological regional specific data is considered all over the year, including a wind rose characterization. The study considered both normal operating conditions and an accidental releases. The results shows that there are a considerable risk due to normal releases in some areas downwind direction of the major releases, and a highly risk in areas subjected to major exposure. Regional maps of emission distribution, economical damage , pollutant concentration are obtained. The study helps to identify solutions to problems of atmospheric protection. It can be used as a decision support for the environmental, economic, and innovation planning at the national levels taking into consideration the national pollution standards and variety of existing emission sources

Stability of large-area molecular junctions

NARCIS (Netherlands)

Akkerman, Hylke B.; Kronemeijer, Auke J.; Harkema, Jan; van Hal, Paul A.; Smits, Edsger C. P.; de Leeuw, Dago M.; Blom, Paul W. M.

The stability of molecular junctions is crucial for any application of molecular electronics. Degradation of molecular junctions when exposed to ambient conditions is regularly observed. In this report the stability of large-area molecular junctions under ambient conditions for more than two years

A review of the epidemiological methods used to investigate the health impacts of air pollution around major industrial areas.

Science.gov (United States)

Pascal, Mathilde; Pascal, Laurence; Bidondo, Marie-Laure; Cochet, Amandine; Sarter, Hélène; Stempfelet, Morgane; Wagner, Vérène

2013-01-01

We performed a literature review to investigate how epidemiological studies have been used to assess the health consequences of living in the vicinity of industries. 77 papers on the chronic effects of air pollution around major industrial areas were reviewed. Major health themes were cancers (27 studies), morbidity (25 studies), mortality (7 studies), and birth outcome (7 studies). Only 3 studies investigated mental health. While studies were available from many different countries, a majority of papers came from the United Kingdom, Italy, and Spain. Several studies were motivated by concerns from the population or by previous observations of an overincidence of cases. Geographical ecological designs were largely used for studying cancer and mortality, including statistical designs to quantify a relationship between health indicators and exposure. Morbidity was frequently investigated through cross-sectional surveys on the respiratory health of children. Few multicenter studies were performed. In a majority of papers, exposed areas were defined based on the distance to the industry and were located from 20 km from the plants. Improving the exposure assessment would be an asset to future studies. Criteria to include industries in multicenter studies should be defined.

Material balance areas and frequencies for large reprocessing plants

International Nuclear Information System (INIS)

Burr, T.

1994-01-01

It has long been recognized that facilities with a large nuclear material throughput will probably not meet the International Atomic Energy Agency (IAEA) goal for detecting trickle diversion of plutonium over periods of about one year. The reason is that measurement errors for plutonium concentration and for liquid volume are often approximately relative over a fairly wide range of true values. Therefore, large throughput facilities will tend to have large uncertainties assigned to their annual throughput. By the same argument, if frequent balances are performed over small material balance areas, then the uncertainty associated with each balance period for each balance area will be small. However, trickle diversion would still be difficult to detect statistically. Because the IAEA will soon be faced with safeguarding a new large-scale reprocessing plant in Japan, it is timely to reconsider the advantages and disadvantages of performing frequent material balances over small balance areas (individual tanks where feasible). Therefore, in this paper the authors present some simulation results to study the effect of balance frequency on loss detection probability, and further simulation results to study possibilities introduced by choosing small balance areas. They conclude by recommending frequent balances over small areas

Large Industrial Point Sources in Italy: a focus on mercury concentrations resulting from three seasonal ship-borne measurements

Directory of Open Access Journals (Sweden)

Bencardino M.

2013-04-01

Full Text Available In Italy there are 25 Large Industrial Point Sources whose mercury emissions in air exceed the established threshold of 10 kg year−1. Many of these mercury point sources, mostly distributed along the Italian coastal area, are located at sites qualified as National Interest Rehabilitation Sites because of documented contamination in qualitative and/or quantitative terms and of potential health impact. Atmospheric mercury emissions related to Italian Large Industrial Point Sources, with a value of 1.04 Mg·yr−1 for 2007, have a not negligible contribution, accounting, on their own, for more than 10% of the total mercury emissions resulting from all activity sectors at a national level. Among others, thermal power stations, pig iron and steel as well as basic inorganic chemical production, result to be the main contributing industrial activities. In order to assess how mercury species concentrations and distribution in the Marine Boundary Layer (MBL change with vicinity to large industrial sites, measurements of atmospheric mercury were performed during three oceanographic campaigns aboard the Research Vessel (R.V. Urania of the Italian CNR. Collection of GEM, GOM and PBM was conducted across the Adriatic sea, during autumn 2004 (27th of October to 12th of November and summer 2005 (17th to 29th of June, and across the Tyrrhenian sea during autumn 2007 (12th of September to 1st October. Analysis were carried out with reference to the period in which the R.V. Urania has stopped close to the main Italian industrial contaminated sites. Explorative statistical parameters of atmospheric mercury species were computed over each single stop-period and then compared with the overall cruise campaign measurements. Results are herein presented and discussed.

Air temperature gradient in large industrial hall

Science.gov (United States)

Karpuk, Michał; Pełech, Aleksander; Przydróżny, Edward; Walaszczyk, Juliusz; Szczęśniak, Sylwia

2017-11-01

In the rooms with dominant sensible heat load, volume airflow depends on many factors incl. pre-established temperature difference between exhaust and supply airflow. As the temperature difference is getting higher, airflow volume drops down, consequently, the cost of AHU is reduced. In high industrial halls with air exhaust grids located under the ceiling additional temperature gradient above working zone should be taken into consideration. In this regard, experimental research of the vertical air temperature gradient in high industrial halls were carried out for the case of mixing ventilation system The paper presents the results of air temperature distribution measurements in high technological hall (mechanically ventilated) under significant sensible heat load conditions. The supply airflow was delivered to the hall with the help of the swirl diffusers while exhaust grids were located under the hall ceiling. Basing on the air temperature distribution measurements performed on the seven pre-established levels, air temperature gradient in the area between 2.0 and 7.0 m above the floor was calculated and analysed.

Groundwater flow in the Venice lagoon and remediation of the Porto Marghera industrial area (Italy)

Science.gov (United States)

Beretta, Giovanni Pietro; Terrenghi, Jacopo

2017-05-01

This study aims to determine the groundwater flow in a large area of the Venice (northeast Italy) lagoon that is under great anthropogenic pressure, which is influencing the regional flow in the surficial aquifer (about 30 m depth). The area presents several elements that condition the groundwater flow: extraction by means of drainage pumps and wells; tidal fluctuation; impermeable barriers that define part of the coastline, rivers and artificial channels; precipitation; recharge, etc. All the elements were studied separately, and then they were brought together in a numerical groundwater flow model to estimate the impact of each one. Identification of the impact of each element will help to optimise the characteristics of the Porto Marghera remediation systems. Longstanding industrial activity has had a strong impact on the soil and groundwater quality, and expensive and complex emergency remediation measures in problematic locations have been undertaken to ensure the continuity of industrial and maritime activities. The land reclamation and remediation works withdraw 56-74% of the water budget, while recharge from the river accounts for about 21-48% of the input. Only 21-42% of groundwater in the modelled area is derived from natural recharge sources, untouched by human activity. The drop of the piezometric level due to the realization of the upgradient impermeable barrier can be counteracted with the reduction of the pumping rate of the remediation systems.

Charge-carrier transport in large-area epitaxial graphene

Energy Technology Data Exchange (ETDEWEB)

Kisslinger, Ferdinand; Popp, Matthias; Weber, Heiko B. [Lehrstuhl fuer Angewandte Physik, Friedrich-Alexander-Universitaet Erlangen-Nuernberg (FAU), Erlangen (Germany); Jobst, Johannes [Huygens-Kamerlingh Onnes Laboratorium, Leiden Institute of Physics, Leiden University (Netherlands); Shallcross, Sam [Lehrstuhl fuer theoretische Festkoerperphysik, Friedrich-Alexander-Universitaet Erlangen-Nuernberg (FAU), Erlangen (Germany)

2017-11-15

We present an overview of recent charge carrier transport experiments in both monolayer and bilayer graphene, with emphasis on the phenomena that appear in large-area samples. While many aspects of transport are based on quantum mechanical concepts, in the large-area limit classical corrections dominate and shape the magnetoresistance and the tunneling conductance. The discussed phenomena are very general and can, with little modification, be expected in any atomically thin 2D conductor. (copyright 2017 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Plan for support of large-plant (post-CRBR) needs in large-leak sodium-water reaction area

International Nuclear Information System (INIS)

Whipple, J.C.

1980-03-01

Work in the large leak test and analysis area of steam generator development has been carried out at GE-ARSD under 189a SG037 since 1973. The currently planned master schedule for the SG037 program is shown. Principal activities are the large leak testing program being carried out at the Large Leak Test Rig and the analysis methods development. The plan for supporting the large plant (post-CRBR) needs in the large leak sodium-water reaction area is outlined. Most of the needs will be answered in the current SG037 large leak program

Regional risk assessment approaches to land planning for industrial polluted areas in China: the Hulunbeier region case study.

Science.gov (United States)

Li, Daiqing; Zhang, Chen; Pizzol, Lisa; Critto, Andrea; Zhang, Haibo; Lv, Shihai; Marcomini, Antonio

2014-04-01

The rapid industrial development and urbanization processes that occurred in China over the past 30years has increased dramatically the consumption of natural resources and raw materials, thus exacerbating the human pressure on environmental ecosystems. In result, large scale environmental pollution of soil, natural waters and urban air were recorded. The development of effective industrial planning to support regional sustainable economy development has become an issue of serious concern for local authorities which need to select safe sites for new industrial settlements (i.e. industrial plants) according to assessment approaches considering cumulative impacts, synergistic pollution effects and risks of accidental releases. In order to support decision makers in the development of efficient and effective regional land-use plans encompassing the identification of suitable areas for new industrial settlements and areas in need of intervention measures, this study provides a spatial regional risk assessment methodology which integrates relative risk assessment (RRA) and socio-economic assessment (SEA) and makes use of spatial analysis (GIS) methodologies and multicriteria decision analysis (MCDA) techniques. The proposed methodology was applied to the Chinese region of Hulunbeier which is located in eastern Inner Mongolia Autonomous Region, adjacent to the Republic of Mongolia. The application results demonstrated the effectiveness of the proposed methodology in the identification of the most hazardous and risky industrial settlements, the most vulnerable regional receptors and the regional districts which resulted to be the most relevant for intervention measures since they are characterized by high regional risk and excellent socio-economic development conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Solution coating of large-area organic semiconductor thin films with aligned single-crystalline domains

KAUST Repository

Diao, Ying

2013-06-02

Solution coating of organic semiconductors offers great potential for achieving low-cost manufacturing of large-area and flexible electronics. However, the rapid coating speed needed for industrial-scale production poses challenges to the control of thin-film morphology. Here, we report an approach - termed fluid-enhanced crystal engineering (FLUENCE) - that allows for a high degree of morphological control of solution-printed thin films. We designed a micropillar-patterned printing blade to induce recirculation in the ink for enhancing crystal growth, and engineered the curvature of the ink meniscus to control crystal nucleation. Using FLUENCE, we demonstrate the fast coating and patterning of millimetre-wide, centimetre-long, highly aligned single-crystalline organic semiconductor thin films. In particular, we fabricated thin films of 6,13-bis(triisopropylsilylethynyl) pentacene having non-equilibrium single-crystalline domains and an unprecedented average and maximum mobilities of 8.1±1.2 cm2 V-1 s -1 and 11 cm2 V-1 s-1. FLUENCE of organic semiconductors with non-equilibrium single-crystalline domains may find use in the fabrication of high-performance, large-area printed electronics. © 2013 Macmillan Publishers Limited. All rights reserved.

Nuclear emergency planning and response in industrial areas. Results of a qualitative study in 9 industrial companies

International Nuclear Information System (INIS)

Pauwels, N.; Hardeman, F.; Soudan, K.

1998-11-01

Substantial economic losses and potential dangerous situations may result when industrial companies unexpectedly have to shut down their activities in an abrupt way. With respect to the industrial companies located in the Antwerp harbour region, the reason for such an unplanned shut-down could be the decision to (preventively) evacuate their workers, or to have them sheltered, in case of an alarm situation at a nearby nuclear power plant of Doel or in any other adjacent industrial factory. Between January and August 1998, the prevention advisors of nine industrial companies have been interviewed to gain insight in the scale and relative importance of several economic costs and practical difficulties that may arise. Moreover, the appropriateness of the existing nuclear emergency response decision structure and intervention philosophy was investigated. The main conclusions drawn from the interviews are reported. Recommendations are made to increase the efficiency of implementing countermeasures in industrial areas

Nuclear emergency planning and response in industrial areas. Results of a qualitative study in 9 industrial companies

Energy Technology Data Exchange (ETDEWEB)

Pauwels, N.; Hardeman, F.; Soudan, K

1998-11-01

Substantial economic losses and potential dangerous situations may result when industrial companies unexpectedly have to shut down their activities in an abrupt way. With respect to the industrial companies located in the Antwerp harbour region, the reason for such an unplanned shut-down could be the decision to (preventively) evacuate their workers, or to have them sheltered, in case of an alarm situation at a nearby nuclear power plant of Doel or in any other adjacent industrial factory. Between January and August 1998, the prevention advisors of nine industrial companies have been interviewed to gain insight in the scale and relative importance of several economic costs and practical difficulties that may arise. Moreover, the appropriateness of the existing nuclear emergency response decision structure and intervention philosophy was investigated. The main conclusions drawn from the interviews are reported. Recommendations are made to increase the efficiency of implementing countermeasures in industrial areas.

Application of CBD-Zinc Sulfide Film as an Antireflection Coating on Very Large Area Multicrystalline Silicon Solar Cell

Directory of Open Access Journals (Sweden)

U. Gangopadhyay

2007-01-01

Full Text Available The low-cost chemical bath deposition (CBD technique is used to prepare CBD-ZnS films as antireflective (AR coating for multicrystalline silicon solar cells. The uniformity of CBD-ZnS film on large area of textured multicrystalline silicon surface is the major challenge of CBD technique. In the present work, attempts have been made for the first time to improve the rate of deposition and uniformity of deposited film by controlling film stoichiometry and refractive index and also to minimize reflection loss by proper optimization of molar percentage of different chemical constituents and deposition conditions. Reasonable values of film deposition rate (12.13 Å′/min., good film uniformity (standard deviation <1, and refractive index (2.35 along with a low percentage of average reflection (6-7% on a textured mc-Si surface are achieved with proper optimization of ZnS bath. 12.24% efficiency on large area (125 mm × 125 mm multicrystalline silicon solar cells with CBD-ZnS antireflection coating has been successfully fabricated. The viability of low-cost CBD-ZnS antireflection coating on large area multicrystalline silicon solar cell in the industrial production level is emphasized.

A large area plastic Cherenkov detector

International Nuclear Information System (INIS)

Bernabei, R.; Bidoli, V.; Zorzi, G. de; Biagio, A. di

1978-01-01

A large area Cherenkov counter has been built up using as a radiator a sheet of Pilot 425 plastic, (180x20)cm 2 x2.5 cm. Experimental tests performed with a pion beam in order to measure the average number of photoelectrons collected by photomultipliers and the scintillation to Cherenkov light ratio. (Auth.)

Large area solid target neutron source

International Nuclear Information System (INIS)

Crawford, J.C.; Bauer, W.

1974-01-01

A potentially useful neutron source may result from the combination of a solid deuterium-tritium loaded target with the large area, high energy ion beams from ion sources being developed for neutral beam injection. The resulting neutron source would have a large radiating area and thus produce the sizable experimental volume necessary for future studies of bulk and synergistic surface radiation effects as well as experiments on engineering samples and small components. With a 200 keV D + T + beam and 40 kW/cm 2 power dissipation on a 200 cm 2 target spot, a total neutron yield of about 4 x 10 15 n/sec may be achieved. Although the useable neutron flux from this source is limited to 1 to 2 x 10 13 n/cm 2 /sec, this flux can be produced 3 cm in front of the target and over about 300 cm 3 of experimental volume. Problems of total power dissipation, sputtering, isotopic flushing and thermal dissociation are reviewed. Neutron flux profiles and potential experimental configurations are presented and compared to other neutron source concepts. (U.S.)

Large area and flexible electronics

CERN Document Server

Caironi, Mario

2015-01-01

From materials to applications, this ready reference covers the entire value chain from fundamentals via processing right up to devices, presenting different approaches to large-area electronics, thus enabling readers to compare materials, properties and performance.Divided into two parts, the first focuses on the materials used for the electronic functionality, covering organic and inorganic semiconductors, including vacuum and solution-processed metal-oxide semiconductors, nanomembranes and nanocrystals, as well as conductors and insulators. The second part reviews the devices and applicatio

Environmental quality indexing of large industrial development alternatives using AHP

International Nuclear Information System (INIS)

Solnes, Julius

2003-01-01

Two industrial development alternatives have been proposed for the East Coast of Iceland in order to strengthen its socio-economic basis. The favoured option is to build a large aluminium smelter, which requires massive hydropower development in the nearby highlands. Another viable option is the construction of a 6-million-ton oil refinery, following the planned exploitation of the Timan Pechora oil reserves in the Russian Arctic. A third 'fictitious' alternative could be general development of existing regional industry and new knowledge-based industries, development of ecotourism, establishment of national parks, accompanied by infrastructure improvement (roads, tunnels, communications, schools, etc.). The three alternatives will have different environmental consequences. The controversial hydropower plant for the smelter requires a large water reservoir as well as considerable land disturbance in this unique mountain territory, considered to be the largest uninhabited wilderness in Western Europe. The aluminium smelter and the oil refinery will give rise to substantial increase of the greenhouse gas (GHG) emissions of the country (about 20%). Then there is potential environmental risk associated with the refinery regarding oil spills at sea, which could have disastrous impact on the fisheries industry. However, the oil refinery does not require any hydropower development, which is a positive factor. Finally, the third alternative could be defined as a ''green'' solution whereby the detrimental environmental consequences of the two industrial solutions are mostly avoided. In order to compare the three alternatives in an orderly manner, the analytic hierarchy process methodology of Saaty was applied to calculate the environmental quality index of each alternative, which is defined as a weighted sum of selected environmental and socio-economic factors. These factors are evaluated on a comparison basis, applying the AHP methodology, and the weights in the quality

Semiconductor-based, large-area, flexible, electronic devices

Science.gov (United States)

Goyal, Amit [Knoxville, TN

2011-03-15

Novel articles and methods to fabricate the same resulting in flexible, large-area, triaxially textured, single-crystal or single-crystal-like, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

Areas of improvement of tax adjustment of industrial enterprises

Directory of Open Access Journals (Sweden)

Abramova Olha

2016-03-01

Full Text Available This article summarizes the scientific approaches and practical experience in theoretical and institutional framework of fiscal management industry. The basic problems in the fiscal management system, the tax regulation methods of large taxpayers are shown. Opportunity is grounded to stimulate the enterprises activity in the directions of tax rates differentiation, tax exemptions and tax credit.

Environmental exposure to arsenic and chromium in an industrial area

OpenAIRE

Vimercati, Luigi; Gatti, Maria F; Gagliardi, Tommaso; Cuccaro, Francesco; De Maria, Luigi; Caputi, Antonio; Quarato, Marco; Baldassarre, Antonio

2017-01-01

Arsenic and chromium are widespread environmental contaminants that affect global health due to their toxicity and carcinogenicity. To date, few studies have investigated exposure to arsenic and chromium in a population residing in a high-risk environmental area. The aim of this study is to evaluate the exposure to arsenic and chromium in the general population with no occupational exposure to these metals, resident in the industrial area of Taranto, Southern Italy, through biological monitor...

Particle physics and polyedra proximity calculation for hazard simulations in large-scale industrial plants

Science.gov (United States)

Plebe, Alice; Grasso, Giorgio

2016-12-01

This paper describes a system developed for the simulation of flames inside an open-source 3D computer graphic software, Blender, with the aim of analyzing in virtual reality scenarios of hazards in large-scale industrial plants. The advantages of Blender are of rendering at high resolution the very complex structure of large industrial plants, and of embedding a physical engine based on smoothed particle hydrodynamics. This particle system is used to evolve a simulated fire. The interaction of this fire with the components of the plant is computed using polyhedron separation distance, adopting a Voronoi-based strategy that optimizes the number of feature distance computations. Results on a real oil and gas refining industry are presented.

Regulations and Strategy for a Loss of Large Area

Energy Technology Data Exchange (ETDEWEB)

Lim, Heok-soon [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The Nuclear Regulatory Commission (NRC) has issued 10 CFR 50.54(hh) that requires licensees to develop guidance and strategies for addressing the loss of large areas of the plant due to explosions or fires from a beyond-design basis event through the use of readily available resources and by identifying potential practicable areas for the use of beyond-readily-available resources. These strategies would address licensee response to events that are beyond the design basis of the facility. This paper illustrates overview of Regulations and some important Strategy for a Loss of Large Area of an advanced nuclear power plant. Regulations and Strategy for Loss of Large Area Analysis could be overlooked during the development stage of Physical Protection System. KHNP was done the project of Physical Protection System design including LOLA to meet the criteria of U.S. NRC and IAEA requirements in INFCIRC/225/Rev.5. The New Reactor should meet the regulatory requirements for LOLA. In the future, the results of project will expect to apply new NPPs.

Mapping the electrical properties of large-area graphene

Science.gov (United States)

Bøggild, Peter; Mackenzie, David M. A.; Whelan, Patrick R.; Petersen, Dirch H.; Due Buron, Jonas; Zurutuza, Amaia; Gallop, John; Hao, Ling; Jepsen, Peter U.

2017-12-01

The significant progress in terms of fabricating large-area graphene films for transparent electrodes, barriers, electronics, telecommunication and other applications has not yet been accompanied by efficient methods for characterizing the electrical properties of large-area graphene. While in the early prototyping as well as research and development phases, electrical test devices created by conventional lithography have provided adequate insights, this approach is becoming increasingly problematic due to complications such as irreversible damage to the original graphene film, contamination, and a high measurement effort per device. In this topical review, we provide a comprehensive overview of the issues that need to be addressed by any large-area characterisation method for electrical key performance indicators, with emphasis on electrical uniformity and on how this can be used to provide a more accurate analysis of the graphene film. We review and compare three different, but complementary approaches that rely either on fixed contacts (dry laser lithography), movable contacts (micro four point probes) and non-contact (terahertz time-domain spectroscopy) between the probe and the graphene film, all of which have been optimized for maximal throughput and accuracy, and minimal damage to the graphene film. Of these three, the main emphasis is on THz time-domain spectroscopy, which is non-destructive, highly accurate and allows both conductivity, carrier density and carrier mobility to be mapped across arbitrarily large areas at rates that by far exceed any other known method. We also detail how the THz conductivity spectra give insights on the scattering mechanisms, and through that, the microstructure of graphene films subject to different growth and transfer processes. The perspectives for upscaling to realistic production environments are discussed.

The current state of taxation and regulation of land plot size of industrial areas in Ukraine

Directory of Open Access Journals (Sweden)

М.А. Malashevskyy

2016-04-01

Full Text Available An analysis of the domestic legal and regulatory framework for land taxation has been performed. The ratio of industry land within the land resources of Ukraine has been investigated. The legal basis for determination of land plot areas necessary for implementation of industrial activities has been considered. The legal regime of industry land has been investigated. The conclusion of the need for improvement of methods for determining excess areas for taxation purposes has been made and optimization of land use in populated areas.

Method for Assessing the Integrated Risk of Soil Pollution in Industrial and Mining Gathering Areas

Science.gov (United States)

Guan, Yang; Shao, Chaofeng; Gu, Qingbao; Ju, Meiting; Zhang, Qian

2015-01-01

Industrial and mining activities are recognized as major sources of soil pollution. This study proposes an index system for evaluating the inherent risk level of polluting factories and introduces an integrated risk assessment method based on human health risk. As a case study, the health risk, polluting factories and integrated risks were analyzed in a typical industrial and mining gathering area in China, namely, Binhai New Area. The spatial distribution of the risk level was determined using a Geographic Information System. The results confirmed the following: (1) Human health risk in the study area is moderate to extreme, with heavy metals posing the greatest threat; (2) Polluting factories pose a moderate to extreme inherent risk in the study area. Such factories are concentrated in industrial and urban areas, but are irregularly distributed and also occupy agricultural land, showing a lack of proper planning and management; (3) The integrated risks of soil are moderate to high in the study area. PMID:26580644

Method for Assessing the Integrated Risk of Soil Pollution in Industrial and Mining Gathering Areas.

Science.gov (United States)

Guan, Yang; Shao, Chaofeng; Gu, Qingbao; Ju, Meiting; Zhang, Qian

2015-11-13

Industrial and mining activities are recognized as major sources of soil pollution. This study proposes an index system for evaluating the inherent risk level of polluting factories and introduces an integrated risk assessment method based on human health risk. As a case study, the health risk, polluting factories and integrated risks were analyzed in a typical industrial and mining gathering area in China, namely, Binhai New Area. The spatial distribution of the risk level was determined using a Geographic Information System. The results confirmed the following: (1) Human health risk in the study area is moderate to extreme, with heavy metals posing the greatest threat; (2) Polluting factories pose a moderate to extreme inherent risk in the study area. Such factories are concentrated in industrial and urban areas, but are irregularly distributed and also occupy agricultural land, showing a lack of proper planning and management; (3) The integrated risks of soil are moderate to high in the study area.

Gas Electron Multipliers: Development of large area GEMs and spherical GEMs

CERN Document Server

Duarte Pinto, Serge; Brock, Ian

2011-01-01

Gaseous radiation detectors have been a crucial part of high-energy physics instrumentation since the 1960s, when the first multiwire proportional counters were built. In the 1990s the first micropattern gas detectors (MPGDs) saw the light; with sub-millimeter feature sizes these novel detectors were faster and more accurate than their predecessors. The gas electron multiplier (GEM) is one of the most successful of these technologies. It is a charge multiplication structure made from a copper clad polymer foil, pierced with a regular and dense pattern of holes. I will describe the properties and the application of GEMs and GEM detectors, and the research and development I have done on this technology. Two of the main objectives were the development of large area GEMs (~m^2) for particle physics experiments and GEMs with a spherical shape for x-ray or neutron diffraction detectors. Both have been realized, and the new techniques involved are finding their way to applications in research and industry.

Gas electron multipliers. Development of large area GEMS and spherical GEMS

Energy Technology Data Exchange (ETDEWEB)

Pinto, Serge Duarte

2011-08-15

Gaseous radiation detectors have been a crucial part of high-energy physics instrumentation since the 1960s, when the first multiwire proportional counters were built. In the 1990s the first micropattern gas detectors (MPGDS) saw the light; with sub-millimeter feature sizes these novel detectors were faster and more accurate than their predecessors. The gas electron multiplier (GEM) is one of the most successful of these technologies. It is a charge multiplication structure made from a copper clad polymer foil, pierced with a regular and dense pattern of holes. I describe the properties and the application of GEMs and GEM. detectors, and the research and development I have done on this technology. Two of the main objectives were the development of large area GEMs ({proportional_to}m{sup 2}) for particle physics experiments and GEMs with a spherical shape for X-ray or neutron diffraction detectors. Both have been realized, and the new techniques involved are finding their way to applications in research and industry. (orig.)

Gas electron multipliers: Development of large area GEMS and spherical GEMS

International Nuclear Information System (INIS)

Pinto, Serge Duarte

2011-08-01

Gaseous radiation detectors have been a crucial part of high-energy physics instrumentation since the 1960s, when the first multiwire proportional counters were built. In the 1990s the first micropattern gas detectors (MPGDS) saw the light; with sub-millimeter feature sizes these novel detectors were faster and more accurate than their predecessors. The gas electron multiplier (GEM) is one of the most successful of these technologies. It is a charge multiplication structure made from a copper clad polymer foil, pierced with a regular and dense pattern of holes. I describe the properties and the application of GEMs and GEM. detectors, and the research and development I have done on this technology. Two of the main objectives were the development of large area GEMs (∝m 2 ) for particle physics experiments and GEMs with a spherical shape for X-ray or neutron diffraction detectors. Both have been realized, and the new techniques involved are finding their way to applications in research and industry. (orig.)

Large-area metallic photonic lattices for military applications.

Energy Technology Data Exchange (ETDEWEB)

Luk, Ting Shan

2007-11-01

In this project we developed photonic crystal modeling capability and fabrication technology that is scaleable to large area. An intelligent optimization code was developed to find the optimal structure for the desired spectral response. In terms of fabrication, an exhaustive survey of fabrication techniques that would meet the large area requirement was reduced to Deep X-ray Lithography (DXRL) and nano-imprint. Using DXRL, we fabricated a gold logpile photonic crystal in the <100> plane. For the nano-imprint technique, we fabricated a cubic array of gold squares. These two examples also represent two classes of metallic photonic crystal topologies, the connected network and cermet arrangement.

Diagnose of large area electron beam with faraday cup

International Nuclear Information System (INIS)

Tang Ying; Qian Hang; Yi Aiping; Huang Xin; Yu Li; Liu Jingru; Su Jiancang; Ding Zhenjie; Ding Yongzhong; Yu Jianguo

2008-01-01

In the experiment of gas laser pumped by electron beam, large area uniform electron beam is important to generate high efficiency laser output. This paper introduces Faraday cup is used in the diagnose experiment on the uniformity of large area e-beam generated by SPG-200 pulsed power generator. Construction of Faraday cup and the results of calibration are presented in detail. The uniformity of velvet emission is given, and the results of experiment are analyzed. (authors)

Advanced Large Area Plastic Scintillator Project (ALPS): Final Report

International Nuclear Information System (INIS)

Jordan, David V.; Reeder, Paul L.; Todd, Lindsay C.; Warren, Glen A.; McCormick, Kathleen R.; Stephens, Daniel L.; Geelhood, Bruce D.; Alzheimer, James M.; Crowell, Shannon L.; Sliger, William A.

2008-01-01

The advanced Large-Area Plastic Scintillator (ALPS) Project at Pacific Northwest National Laboratory investigated possible technological avenues for substantially advancing the state-of-the-art in gamma-ray detection via large-area plastic scintillators. The three predominant themes of these investigations comprised the following: * Maximizing light collection efficiency from a single large-area sheet of plastic scintillator, and optimizing hardware event trigger definition to retain detection efficiency while exploiting the power of coincidence to suppress single-PMT 'dark current' background; * Utilizing anti-Compton vetoing and supplementary spectral information from a co-located secondary, or 'Back' detector, to both (1) minimize Compton background in the low-energy portion of the 'Front' scintillator's pulse-height spectrum, and (2) sharpen the statistical accuracy of the front detector's low-energy response prediction as implemented in suitable energy-windowing algorithms; and * Investigating alternative materials to enhance the intrinsic gamma-ray detection efficiency of plastic-based sensors

Large-area high-efficiency flexible PHOLED lighting panels

Science.gov (United States)

Pang, Huiqing; Mandlik, Prashant; Levermore, Peter A.; Silvernail, Jeff; Ma, Ruiqing; Brown, Julie J.

2012-09-01

Organic Light Emitting Diodes (OLEDs) provide various attractive features for next generation illumination systems, including high efficiency, low power, thin and flexible form factor. In this work, we incorporated phosphorescent emitters and demonstrated highly efficient white phosphorescent OLED (PHOLED) devices on flexible plastic substrates. The 0.94 cm2 small-area device has total thickness of approximately 0.25 mm and achieved 63 lm/W at 1,000 cd/m2 with CRI = 85 and CCT = 2920 K. We further designed and fabricated a 15 cm x 15 cm large-area flexible white OLED lighting panels, finished with a hybrid single-layer ultra-low permeability single layer barrier (SLB) encapsulation film. The flexible panel has an active area of 116.4 cm2, and achieved a power efficacy of 47 lm/W at 1,000 cd/m2 with CRI = 83 and CCT = 3470 K. The efficacy of the panel at 3,000 cd/m2 is 43 lm/W. The large-area flexible PHOLED lighting panel is to bring out enormous possibilities to the future general lighting applications.

Large area synchrotron X-ray fluorescence mapping of biological samples

International Nuclear Information System (INIS)

Kempson, I.; Thierry, B.; Smith, E.; Gao, M.; De Jonge, M.

2014-01-01

Large area mapping of inorganic material in biological samples has suffered severely from prohibitively long acquisition times. With the advent of new detector technology we can now generate statistically relevant information for studying cell populations, inter-variability and bioinorganic chemistry in large specimen. We have been implementing ultrafast synchrotron-based XRF mapping afforded by the MAIA detector for large area mapping of biological material. For example, a 2.5 million pixel map can be acquired in 3 hours, compared to a typical synchrotron XRF set-up needing over 1 month of uninterrupted beamtime. Of particular focus to us is the fate of metals and nanoparticles in cells, 3D tissue models and animal tissues. The large area scanning has for the first time provided statistically significant information on sufficiently large numbers of cells to provide data on intercellular variability in uptake of nanoparticles. Techniques such as flow cytometry generally require analysis of thousands of cells for statistically meaningful comparison, due to the large degree of variability. Large area XRF now gives comparable information in a quantifiable manner. Furthermore, we can now image localised deposition of nanoparticles in tissues that would be highly improbable to 'find' by typical XRF imaging. In addition, the ultra fast nature also makes it viable to conduct 3D XRF tomography over large dimensions. This technology avails new opportunities in biomonitoring and understanding metal and nanoparticle fate ex-vivo. Following from this is extension to molecular imaging through specific anti-body targeted nanoparticles to label specific tissues and monitor cellular process or biological consequence

Eco-industrial zones in the context of sustainability development of urban areas.

Science.gov (United States)

Sacirovic, Selim; Ketin, Sonja; Vignjevic, Nada

2018-03-04

Industry is one of the main activities in the city and in many cities of the world, and the dominant industrial zones are the most significant morphological forms of concentration of industrial facilities in the city and are concentrated industrial and business activity. Industrial parks combine activities related to energy and resource consumption, emissions, waste generation, economic benefits, and regional development. The focus of this work is the path of transformation between the present and the vision of a sustainable city in the future. The problem and the subject of research related to two related objects of research: the city and sustainable development. In this paper, the co-author's industrial symbiosis parks, modern tendencies of the spatial distribution of productive activities, circular economy, to attract leading corporations and open the way for new ventures while preserving the living environment in an urban area.

Area Factor Determinations for an Industrial Worker Exposed to a Concrete Slab End-State

International Nuclear Information System (INIS)

Jannik, G. Timothy; Lee, Patricia L.; Farfan, Eduardo B.; Roach, Jesse L.

2008-01-01

The U.S. Department of Energy's (DOE) Savannah River Site (SRS) is decommissioning many of its excess facilities through removal of the facility structures leaving only the concrete-slab foundations in place. Site-specific, risk-based derived concentration guideline levels (DCGLs) for radionuclides have been determined for a future industrial worker potentially exposed to residual contamination on these concrete slabs as described in Jannik. These risk-based DCGLs were estimated for an exposure area of 100 m 2 . During deactivation and decommissioning (D and D) operations at SRS, the need for area factors for larger and smaller contaminated areas arose. This paper compares the area factors determined for an industrial worker exposed to a concrete slab end-state for several radionuclides of concern at SRS with 1) the illustrative area factors provided in MARSSIM, 2) the area correction factors provided in the U.S. Environmental Protection Agency's (EPA) Soil Screening Guidance, and 3) the hot spot criterion for field application provided in the RESRAD User's Manual. The purpose of this site-specific assessment is to determine if any of the recommended area factors provided in the guidance documents could be utilized at SRS for field applications of the industrial worker DCGLs. Results show the area factors that were determined for an SRS industrial worker exposed to concrete slab end-states for the common radionuclides provided in the referenced guidance documents. In addition to the SRS site-specific area factors, the following area factors are provided for comparison: - Illustrative examples of outdoor area dose factors (MARSSIM); - Area correction factors as a function of source area (Soil Screening Guidance). Note: the area correction factors were inverted to correspond to a DCGL area factor. - Recommended area correction factors as a function of source area (Soil Screening Guidance); - Ranges for hot spot multiplication factors (RESRAD). As it can be seen

Quantitative Mapping of Large Area Graphene Conductance

DEFF Research Database (Denmark)

Buron, Jonas Christian Due; Petersen, Dirch Hjorth; Bøggild, Peter

2012-01-01

We present quantitative mapping of large area graphene conductance by terahertz time-domain spectroscopy and micro four point probe. We observe a clear correlation between the techniques and identify the observed systematic differences to be directly related to imperfections of the graphene sheet...

Optical fabrication of large area photonic microstructures by spliced lens

Science.gov (United States)

Jin, Wentao; Song, Meng; Zhang, Xuehua; Yin, Li; Li, Hong; Li, Lin

2018-05-01

We experimentally demonstrate a convenient approach to fabricate large area photorefractive photonic microstructures by a spliced lens device. Large area two-dimensional photonic microstructures are optically induced inside an iron-doped lithium niobate crystal. The experimental setups of our method are relatively compact and stable without complex alignment devices. It can be operated in almost any optical laboratories. We analyze the induced triangular lattice microstructures by plane wave guiding, far-field diffraction pattern imaging and Brillouin-zone spectroscopy. By designing the spliced lens appropriately, the method can be easily extended to fabricate other complex large area photonic microstructures, such as quasicrystal microstructures. Induced photonic microstructures can be fixed or erased and re-recorded in the photorefractive crystal.

Evolution of industrial wastewater pollution in the Barcelona Metropolitan Area; Evolucion de la contaminacion industrial en las aguas residuales del area metropolitana de Barcelona

Energy Technology Data Exchange (ETDEWEB)

Mantecon Pascual, R.

2005-07-01

The Environmental Agency of the Barcelona Metropolitan Area has full powers regarding sewerage. Industrial wastewater emptied into the public sewer system has been monitored and analysed since 1988. the data showing the evolution of the pollution in industrial wastewater are presented, broken down by activities and parameters. These data are based on the analysis of 14,528 samples taken during 19,555 inspections of 5,655 factories. It was found that there has been a gradual improvement in the quality of the effluents. Failure to meet the requirements concerning one or more of the physico-chemical parameters fell from 71% to 39% of the samples analysed. (Author)

Advanced Large Area Plastic Scintillator Project (ALPS): Final Report

Energy Technology Data Exchange (ETDEWEB)

Jordan, David V.; Reeder, Paul L.; Todd, Lindsay C.; Warren, Glen A.; McCormick, Kathleen R.; Stephens, Daniel L.; Geelhood, Bruce D.; Alzheimer, James M.; Crowell, Shannon L.; Sliger, William A.

2008-02-05

The advanced Large-Area Plastic Scintillator (ALPS) Project at Pacific Northwest National Laboratory investigated possible technological avenues for substantially advancing the state-of-the-art in gamma-ray detection via large-area plastic scintillators. The three predominant themes of these investigations comprised the following: * Maximizing light collection efficiency from a single large-area sheet of plastic scintillator, and optimizing hardware event trigger definition to retain detection efficiency while exploiting the power of coincidence to suppress single-PMT "dark current" background; * Utilizing anti-Compton vetoing and supplementary spectral information from a co-located secondary, or "Back" detector, to both (1) minimize Compton background in the low-energy portion of the "Front" scintillator's pulse-height spectrum, and (2) sharpen the statistical accuracy of the front detector's low-energy response prediction as impelmented in suitable energy-windowing algorithms; and * Investigating alternative materials to enhance the intrinsic gamma-ray detection efficiency of plastic-based sensors.

Postwar Industrial areas as agents for sustainable urban transformation

DEFF Research Database (Denmark)

Boye, Anne Mette

2017-01-01

Only 30-40 years old, postwar industrial enclaves in Denmark change character. Vacancies, new investments in high technology and new civic programs are recorded even within the same enclaves. These postwar industrial areas represent a generic typology – a legacy of the functionalistic paradigm sh...... international projects, the paper pinpoints a selection of spatial transformation strategies addressing uncertainty. Through this, the paper contributes to the discussion on how to recycle the postwar urban landscape and planning in uncertain conditions....... are cleared for redevelopment or ignored. However, both reactions dismiss the possible qualities of the existing morphology and activities. This paper argues that this might close an opportunity to consider how recycling these enclaves can be utilized to shape future sustainable urban environments...

Large-area, laterally-grown epitaxial semiconductor layers

Science.gov (United States)

Han, Jung; Song, Jie; Chen, Danti

2017-07-18

Structures and methods for confined lateral-guided growth of a large-area semiconductor layer on an insulating layer are described. The semiconductor layer may be formed by heteroepitaxial growth from a selective growth area in a vertically-confined, lateral-growth guiding structure. Lateral-growth guiding structures may be formed in arrays over a region of a substrate, so as to cover a majority of the substrate region with laterally-grown epitaxial semiconductor tiles. Quality regions of low-defect, stress-free GaN may be grown on silicon.

Estimation of heavy metals in dust fall samples from three different industrial areas of Karachi

International Nuclear Information System (INIS)

Hashmi, D.R.; Khan, F.A.; Shareef, A.; Bano, A.B.; Munshi, A.B.

2010-01-01

The study of accumulation of heavy metals, Fe, Cu, Mn, Zn, Pb and Cd, in the dust fall samples, collected from three selected industrial areas of Karachi, showed the level of heavy metals to decrease gradually from sites of high activity to those of low activity such as from roundabouts to main roads to side roads. Concentration of heavy metal showed a variation of the order Fe>Zn>Pb>Mn>Cu>Cd. Iron had the highest concentration in all the sampling areas in the range of 1.947 +- 0.00 to 30.039 +- 0.01 mg/g. Lower values were observed for Cd with respective ranges of 0.001 +- 0.00 to 0.009 +- 0.01 mg/g. The results suggested that heavy metal pollution in the dust fall samples of industrial areas may be due to automobile and industrial exhaust from different industrial units. (author)

Amplifiers dedicated for large area SiC photodiodes

Science.gov (United States)

Doroz, P.; Duk, M.; Korwin-Pawlowski, M. L.; Borecki, M.

2016-09-01

Large area SiC photodiodes find applications in optoelectronic sensors working at special conditions. These conditions include detection of UV radiation in harsh environment. Moreover, the mentioned sensors have to be selective and resistant to unwanted signals. For this purpose, the modulation of light at source unit and the rejection of constant current and low frequency component of signal at detector unit are used. The popular frequency used for modulation in such sensor is 1kHz. The large area photodiodes are characterized by a large capacitance and low shunt resistance that varies with polarization of the photodiode and can significantly modify the conditions of signal pre-amplification. In this paper two pre-amplifiers topology are analyzed: the transimpedance amplifier and the non-inverting voltage to voltage amplifier with negative feedback. The feedback loops of both pre-amplifiers are equipped with elements used for initial constant current and low frequency signals rejections. Both circuits are analyzed and compared using simulation and experimental approaches.

Risk management for industrial safety

International Nuclear Information System (INIS)

Novogno, A.

1989-01-01

The catastrophic accidents which have occurred in the last decade, in both developed and developing countries, have drawn the attention of decision-makers in the safety area to the urgent necessity to assess and manage risks from hazardous industrial activities which are concentrated in large industrialized areas. The aim of this paper is to review experience gained in conducting studies in the area of 'comparisons of risks in energy systems' and on the practical application of 'cost effectiveness of risk reduction analysis among different energy systems' (case studies). It is also the aim of the paper to discuss and propose a general framework for defining an 'integrated approach' to risk assessment and management in highly industrialized regions within a country. (author)

Electrothermal Simulation of Large-Area Semiconductor Devices

Directory of Open Access Journals (Sweden)

C Kirsch

2017-06-01

Full Text Available The lateral charge transport in thin-film semiconductor devices is affected by the sheet resistance of the various layers. This may lead to a non-uniform current distribution across a large-area device resulting in inhomogeneous luminance, for example, as observed in organic light-emitting diodes (Neyts et al., 2006. The resistive loss in electrical energy is converted into thermal energy via Joule heating, which results in a temperature increase inside the device. On the other hand, the charge transport properties of the device materials are also temperature-dependent, such that we are facing a two-way coupled electrothermal problem. It has been demonstrated that adding thermal effects to an electrical model significantly changes the results (Slawinski et al., 2011. We present a mathematical model for the steady-state distribution of the electric potential and of the temperature across one electrode of a large-area semiconductor device, as well as numerical solutions obtained using the finite element method.

Large-area smart glass and integrated photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Lampert, C.M. [Star Science, 8730 Water Road, Cotati, CA 94931-4252 (United States)

2003-04-01

Several companies throughout the world are developing dynamic glazing and large-area flat panel displays. University and National Laboratory groups are researching new materials and processes to improve these products. The concept of a switchable glazing for building and vehicle application is very attractive. Conventional glazing only offers fixed transmittance and control of energy passing through it. Given the wide range of illumination conditions and glare, a dynamic glazing with adjustable transmittance offers the best solution. Photovoltaics can be integrated as power sources for smart windows. In this way a switchable window could be a completely stand alone smart system. A new range of large-area flat panel display including light-weight and flexible displays are being developed. These displays can be used for banner advertising, dynamic pricing in stores, electronic paper, and electronic books, to name only a few applications. This study covers selected switching technologies including electrochromism, suspended particles, and encapsulated liquid crystals.

Impacts of Large Scale Wind Penetration on Energy Supply Industry

Directory of Open Access Journals (Sweden)

John Kabouris

2009-11-01

Full Text Available Large penetration of Renewable Energy Sources (RES impacts Energy Supply Industry (ESI in many aspects leading to a fundamental change in electric power systems. It raises a number of technical challenges to the Transmission System Operators (TSOs, Distribution System Operators (DSOs and Wind Turbine Generators (WTG constructors. This paper aims to present in a thorough and coherent way the redrawn picture for Energy Systems under these conditions. Topics related to emergent technical challenges, technical solutions required and finally the impact on ESI due to large wind power penetration, are analyzed. Finally, general conclusions are extracted about the ESI current and future state and general directions are recommended.

Heavy Metal In Food Ingredients In Oil Refi nery Industrial Area, Dumai

Directory of Open Access Journals (Sweden)

Dian Sundari

2016-06-01

Full Text Available Background: Industrial waste generally contains a lot of heavy metals such as Plumbum (Pb, Arsenic (As, Cadmium(Cd and Mercury (Hg, which can contaminate the surrounding environment and cause health problems. Bioaccumulation ofheavy metals from the environment can occur in foodstuffs. The study aims to determine levels of heavy metals Pb, Cd, Asand Hg in foodstuffs in the oil refi nery industry. Methods: The analytical method used Atomic Absorption Spectrophotometer(AAS. Samples were taken from two locations, namely: the exposed area and non exposed area. The sample consisted ofcassava, papaya leaves, fern leaves, cassava leaves, guava, papaya and catfi sh. Results: The analysis showed levels ofmetals As in all samples at exposed locations is below the maximum limit of SNI, the location is not exposed only in catfi shlevels of As (2.042 mg/kg exceeds the SNI. Cd levels of both locations are not detected. Pb levels in catfi sh in exposedlocations (1,109 mg/kg exceeds the SNI. Hg levels in leaves of papaya, cassava leaves, fern leaves, cassava and fruitpapaya exceed SNI. Conclusion: There has been a heavy metal contamination in foodstuffs. Recommendation: Thelocal people are advised to be careful when consuming food stuffs from oil refi nery industrial area.

Safety of Nanotechnology in Food Industries

Science.gov (United States)

Amini, Seyed Mohammad; Gilaki, Marzieh; Karchani, Mohsen

2014-01-01

The arrival of nanotechnology in various industries has been so rapid and widespread because of its wide-ranging applications in our daily lives. Nutrition and food service is one of the biggest industries to be affected by nanotechnology in all areas, changing even the nature of food itself. Whether it’s farming, food packaging, or the prevention of microbial contamination the major food industries have seen dramatic changes because of nanotechnology. Different nanomaterials such as nanopowders, nanotubes, nano-fibers, quantum dots, and metal and metal-oxide nanoparticles are globally produced in large quantities due to their broad applicability in food-related industries. Because of the unique properties of nanostructures and nanomaterials – such as a large surface area, high activity, and small size, there is some concern about the potential for harmful adverse effects of used nanomaterials on health or the environment. However, because of tremendous advances in different industries, this concern may be unnecessary. This paper presents some uses of nanomaterials in food and related industries and their possible side-effects. This review covers the various aspects of nanomaterials and their impact on human exposure, safety, and environmental concerns. PMID:25763176

A facile alternative technique for large-area graphene transfer via sacrificial polymer

Directory of Open Access Journals (Sweden)

Eric Auchter

2017-12-01

Full Text Available A novel method of transferring large-area graphene sheets onto a variety of substrates using Formvar (polyvinyl formal is presented. Due to the ease at which formvar can be dissolved in chloroform this method allows for a consistent, a clean, and a more rapid transfer than other techniques including the PMMA assisted one. This novel transfer method is demonstrated by transferring large-area graphene onto a range of substrates including commercial TEM grids, silicon dioxide and glass. Raman spectroscopy was used to confirm the presence of graphene and characterize the morphological properties of the large-area sheets. SEM and AFM analyses demonstrated the effectiveness of our rapid transfer technique for clean crystalline large-area graphene sheets. The removal of the sacrificial polymer was found to be one to two orders of magnitude faster than PMMA methods. Ultimately this facile transfer technique offers new opportunities for a wide range of applications for large-area graphene through the utilization of a new sacrificial polymer.

Changing industrial patterns in the metroplitan Chicago area

Energy Technology Data Exchange (ETDEWEB)

Allardice, D.

1994-12-31

The industrial base of Chicago, and most Midwestern cities, continues to change. These changes are particularly visible in the manufacturing sector where the exodus of companies has left behind abandoned factories and industrial sites that now blight the urban landscape. As urban centers have seen a steady decline in their ability to attract and maintain their manufacturing base, great interest has been placed in seeing what can be done to attract economic activity back into the urban center. For most Midwestern cities, this often means trying to either replace or stem the tide of manufacturing facilities that have left the city for {open_quotes}greenfields{close_quotes} in suburban or rural locations or have simply moved overseas. On the replacement front, to compensate for the loss of manufacturing, some cities such as Chicago have managed to expand other areas of their economies, such as business services, finance, and tourism and recreation to maintain their vitality. This paper discusses three aspects of the changing economic landscape of Chicago and other Midwestern urban areas. First, some historical perspective will be provided on how Chicago came to be a manufacturing center and what factors since World War II have led manufacturing facilities to move away from the urban center. Second, the future prospects for manufacturing in the central city will be examined. Finally, what policies may help increase (or at the very least maintain) the concentration of manufacturing in Chicago will be discussed.

Changing industrial patterns in the metroplitan Chicago area

International Nuclear Information System (INIS)

Allardice, D.

1994-01-01

The industrial base of Chicago, and most Midwestern cities, continues to change. These changes are particularly visible in the manufacturing sector where the exodus of companies has left behind abandoned factories and industrial sites that now blight the urban landscape. As urban centers have seen a steady decline in their ability to attract and maintain their manufacturing base, great interest has been placed in seeing what can be done to attract economic activity back into the urban center. For most Midwestern cities, this often means trying to either replace or stem the tide of manufacturing facilities that have left the city for open-quotes greenfieldsclose quotes in suburban or rural locations or have simply moved overseas. On the replacement front, to compensate for the loss of manufacturing, some cities such as Chicago have managed to expand other areas of their economies, such as business services, finance, and tourism and recreation to maintain their vitality. This paper discusses three aspects of the changing economic landscape of Chicago and other Midwestern urban areas. First, some historical perspective will be provided on how Chicago came to be a manufacturing center and what factors since World War II have led manufacturing facilities to move away from the urban center. Second, the future prospects for manufacturing in the central city will be examined. Finally, what policies may help increase (or at the very least maintain) the concentration of manufacturing in Chicago will be discussed

Large-area mapping of biodiversity

Science.gov (United States)

Scott, J.M.; Jennings, M.D.

1998-01-01

The age of discovery, description, and classification of biodiversity is entering a new phase. In responding to the conservation imperative, we can now supplement the essential work of systematics with spatially explicit information on species and assemblages of species. This is possible because of recent conceptual, technical, and organizational progress in generating synoptic views of the earth's surface and a great deal of its biological content, at multiple scales of thematic as well as geographic resolution. The development of extensive spatial data on species distributions and vegetation types provides us with a framework for: (a) assessing what we know and where we know it at meso-scales, and (b) stratifying the biological universe so that higher-resolution surveys can be more efficiently implemented, coveting, for example, geographic adequacy of specimen collections, population abundance, reproductive success, and genetic dynamics. The land areas involved are very large, and the questions, such as resolution, scale, classification, and accuracy, are complex. In this paper, we provide examples from the United States Gap Analysis Program on the advantages and limitations of mapping the occurrence of terrestrial vertebrate species and dominant land-cover types over large areas as joint ventures and in multi-organizational partnerships, and how these cooperative efforts can be designed to implement results from data development and analyses as on-the-ground actions. Clearly, new frameworks for thinking about biogeographic information as well as organizational cooperation are needed if we are to have any hope of documenting the full range of species occurrences and ecological processes in ways meaningful to their management. The Gap Analysis experience provides one model for achieving these new frameworks.

Background radiation study of Offa industrial area of Kwara State ...

African Journals Online (AJOL)

A study of the external background radiation in Offa industrial area of Kwara State is hereby reported. An in-situ measurement using two Digilert radiation monitors at five different stations were carried out. A mean exposure rate of 0.0132mR/hr, which represents 20% elevation from the standard background radiation, was ...

Automated Bug Assignment: Ensemble-based Machine Learning in Large Scale Industrial Contexts

OpenAIRE

Jonsson, Leif; Borg, Markus; Broman, David; Sandahl, Kristian; Eldh, Sigrid; Runeson, Per

2016-01-01

Bug report assignment is an important part of software maintenance. In particular, incorrect assignments of bug reports to development teams can be very expensive in large software development projects. Several studies propose automating bug assignment techniques using machine learning in open source software contexts, but no study exists for large-scale proprietary projects in industry. The goal of this study is to evaluate automated bug assignment techniques that are based on machine learni...

The emerging role of large eddy simulation in industrial practice: challenges and opportunities.

Science.gov (United States)

Hutton, A G

2009-07-28

That class of methods for treating turbulence gathered under the banner of large eddy simulation is poised to enter mainstream engineering practice. There is a growing body of evidence that such methods offer a significant stretch in industrial capability over solely Reynolds-averaged Navier-Stokes (RANS)-based modelling. A key enabling development will be the adaptation of innovative processor architectures, resulting from the huge investment in the gaming industry, to engineering analysis. This promises to reduce the computational burden to practicable levels. However, there are many lessons to be learned from the history of the past three decades. These lessons should be analysed in order to inform, if not modulate, the unfolding of this next cycle in the development of industrial modelling capability. This provides the theme for this paper, which is written very much from the standpoint of the informed practitioner rather than the innovator; someone with a strong motivation to improve significantly the competence with which industrial turbulent flows are treated. It is asserted that the reliable deployment of the methodology in the industrial context will prove to be a knowledge-based discipline, as was the case with RANS-based modelling, if not more so. The community at large should collectively make great efforts to put in place that knowledge base from which best practice advice can be derived at the very start of this cycle of advancement and continue to enrich it as the cycle progresses.

Spatially explicit shallow landslide susceptibility mapping over large areas

Science.gov (United States)

Bellugi, Dino; Dietrich, William E.; Stock, Jonathan D.; McKean, Jim; Kazian, Brian; Hargrove, Paul

2011-01-01

Recent advances in downscaling climate model precipitation predictions now yield spatially explicit patterns of rainfall that could be used to estimate shallow landslide susceptibility over large areas. In California, the United States Geological Survey is exploring community emergency response to the possible effects of a very large simulated storm event and to do so it has generated downscaled precipitation maps for the storm. To predict the corresponding pattern of shallow landslide susceptibility across the state, we have used the model Shalstab (a coupled steady state runoff and infinite slope stability model) which susceptibility spatially explicit estimates of relative potential instability. Such slope stability models that include the effects of subsurface runoff on potentially destabilizing pore pressure evolution require water routing and hence the definition of upslope drainage area to each potential cell. To calculate drainage area efficiently over a large area we developed a parallel framework to scale-up Shalstab and specifically introduce a new efficient parallel drainage area algorithm which produces seamless results. The single seamless shallow landslide susceptibility map for all of California was accomplished in a short run time, and indicates that much larger areas can be efficiently modelled. As landslide maps generally over predict the extent of instability for any given storm. Local empirical data on the fraction of predicted unstable cells that failed for observed rainfall intensity can be used to specify the likely extent of hazard for a given storm. This suggests that campaigns to collect local precipitation data and detailed shallow landslide location maps after major storms could be used to calibrate models and improve their use in hazard assessment for individual storms.

Assessment of clean development mechanism potential of large-scale energy efficiency measures in heavy industries

International Nuclear Information System (INIS)

Hayashi, Daisuke; Krey, Matthias

2007-01-01

This paper assesses clean development mechanism (CDM) potential of large-scale energy efficiency measures in selected heavy industries (iron and steel, cement, aluminium, pulp and paper, and ammonia) taking India and Brazil as examples of CDM project host countries. We have chosen two criteria for identification of the CDM potential of each energy efficiency measure: (i) emission reductions volume (in CO 2 e) that can be expected from the measure and (ii) likelihood of the measure passing the additionality test of the CDM Executive Board (EB) when submitted as a proposed CDM project activity. The paper shows that the CDM potential of large-scale energy efficiency measures strongly depends on the project-specific and country-specific context. In particular, technologies for the iron and steel industry (coke dry quenching (CDQ), top pressure recovery turbine (TRT), and basic oxygen furnace (BOF) gas recovery), the aluminium industry (point feeder prebake (PFPB) smelter), and the pulp and paper industry (continuous digester technology) offer promising CDM potential

Large area modules based on low band gap polymers

DEFF Research Database (Denmark)

Bundgaard, Eva; Krebs, Frederik C

2010-01-01

The use of three low band gap polymers in large area roll-to-roll coated modules is demonstrated. The polymers were prepared by a Stille cross coupling polymerization and all had a band gap around 1.6 eV. The polymers were first tested in small area organic photovoltaic devices which showed...

Plasma and Ion Sources in Large Area Coatings: A Review

Energy Technology Data Exchange (ETDEWEB)

Anders, Andre

2005-02-28

Efficient deposition of high-quality coatings often requires controlled application of excited or ionized particles. These particles are either condensing (film-forming) or assisting by providing energy and momentum to the film growth process, resulting in densification, sputtering/etching, modification of stress, roughness, texture, etc. In this review, the technical means are surveyed enabling large area application of ions and plasmas, with ion energies ranging from a few eV to a few keV. Both semiconductortype large area (single wafer or batch processing with {approx} 1000 cm{sup 2}) and in-line web and glass-coating-type large area (> 10{sup 7} m{sup 2} annually) are considered. Characteristics and differences between plasma and ion sources are explained. The latter include gridded and gridless sources. Many examples are given, including sources based on DC, RF, and microwave discharges, some with special geometries like hollow cathodes and E x B configurations.

Large-area and highly crystalline MoSe2 for optical modulator

Science.gov (United States)

Yin, Jinde; Chen, Hao; Lu, Wei; Liu, Mengli; Li, Irene Ling; Zhang, Min; Zhang, Wenfei; Wang, Jinzhang; Xu, Zihan; Yan, Peiguang; Liu, Wenjun; Ruan, Shuangchen

2017-12-01

Transition metal dichalcogenides (TMDs) have been successfully used as broadband optical modulator materials for pulsed fiber laser systems. However, the nonlinear optical absorptions of exfoliated TMDs are strongly limited by their nanoflakes morphology with uncontrollable lateral size and thickness. In this work, we provide an effective method to fully explore the nonlinear optical properties of MoSe2. Large-area and high quality lattice MoSe2 grown by chemical vapor deposition method was adopted as an optical modulator for the first time. The large-area MoSe2 shows excellent nonlinear optical absorption with a large modulation depth of 21.7% and small saturable intensity of 9.4 MW cm-2. After incorporating the MoSe2 optical modulator into fiber laser cavity as a saturable absorber, a highly stable Q-switching operation with single pulse energy of 224 nJ is achieved. The large-area MoSe2 possessing superior nonlinear optical properties compared to exfoliated nanoflakes affords possibility for the larger-area two-dimensional materials family as high performance optical devices.

Design of General-purpose Industrial signal acquisition system in a large scientific device

Science.gov (United States)

Ren, Bin; Yang, Lei

2018-02-01

In order to measure the industrial signal of a large scientific device experiment, a set of industrial data general-purpose acquisition system has been designed. It can collect 4~20mA current signal and 0~10V voltage signal. Through the practical experiments, it shows that the system is flexible, reliable, convenient and economical, and the system has characters of high definition and strong anti-interference ability. Thus, the system fully meets the design requirements..

Blood biomonitoring of metals in subjects living near abandoned mining and active industrial areas.

Science.gov (United States)

Madeddu, Roberto; Tolu, Paola; Asara, Yolande; Farace, Cristiano; Forte, Giovanni; Bocca, Beatrice

2013-07-01

A human blood biomonitoring campaign to detect the environmental exposure to metals (Cd, Cu, Cr, Mn, Pb and Zn) in 265 subjects was performed in the South-Western part of Sardinia (an Italian island) that is a particular area with a great history of coal and metal mining (Pb/Zn mainly) activities and large industrial structures (as metallurgy). Subjects living near the industrial plant area had geometric means (GM) of blood Cd (0.79 μg/l), Cu (971 μg/l), Mn (12.2 μg/l), and Pb (55.7 μg/l) significantly higher than controls (Cd, 0.47 μg/l; Cu, 900 μg/l; Mn 9.98 μg/l; Pb, 26.5 μg/l) and than people living nearby the past mining sites. Subjects living next to one dismissed mine were statistically higher in blood Cu (GM, 1,022 μg/l) and Pb (GM, 41.4 μg/l) concentrations than controls. No differences were observed in people living in the different mining sites, and this might be related to the decennial disclosure of mines and the adoption of environmental remediation programmes. Some interindividual variables influenced blood biomonitoring data, as smoke and age for Cd, gender for Cu, age, sex and alcohol for Pb, and age for Zn. Moreover, blood metal levels of the whole population were similar to reference values representative of the Sardinian population and acceptably safe according to currently available health guidelines.

Spatially explicit shallow landslide susceptibility mapping over large areas

Science.gov (United States)

Dino Bellugi; William E. Dietrich; Jonathan Stock; Jim McKean; Brian Kazian; Paul Hargrove

2011-01-01

Recent advances in downscaling climate model precipitation predictions now yield spatially explicit patterns of rainfall that could be used to estimate shallow landslide susceptibility over large areas. In California, the United States Geological Survey is exploring community emergency response to the possible effects of a very large simulated storm event and to do so...

Fuzzy logic applied to prospecting for areas for installation of wood panel industries.

Science.gov (United States)

Dos Santos, Alexandre Rosa; Paterlini, Ewerthon Mattos; Fiedler, Nilton Cesar; Ribeiro, Carlos Antonio Alvares Soares; Lorenzon, Alexandre Simões; Domingues, Getulio Fonseca; Marcatti, Gustavo Eduardo; de Castro, Nero Lemos Martins; Teixeira, Thaisa Ribeiro; Dos Santos, Gleissy Mary Amaral Dino Alves; Juvanhol, Ronie Silva; Branco, Elvis Ricardo Figueira; Mota, Pedro Henrique Santos; da Silva, Lilianne Gomes; Pirovani, Daiani Bernardo; de Jesus, Waldir Cintra; Santos, Ana Carolina de Albuquerque; Leite, Helio Garcia; Iwakiri, Setsuo

2017-05-15

Prospecting for suitable areas for forestry operations, where the objective is a reduction in production and transportation costs, as well as the maximization of profits and available resources, constitutes an optimization problem. However, fuzzy logic is an alternative method for solving this problem. In the context of prospecting for suitable areas for the installation of wood panel industries, we propose applying fuzzy logic analysis for simulating the planting of different species and eucalyptus hybrids in Espírito Santo State, Brazil. The necessary methodological steps for this study are as follows: a) agriclimatological zoning of different species and eucalyptus hybrids; b) the selection of the vector variables; c) the application of the Euclidean distance to the vector variables; d) the application of fuzzy logic to matrix variables of the Euclidean distance; and e) the application of overlap fuzzy logic to locate areas for installation of wood panel industries. Among all the species and hybrids, Corymbia citriodora showed the highest percentage values for the combined very good and good classes, with 8.60%, followed by Eucalyptus grandis with 8.52%, Eucalyptus urophylla with 8.35% and Urograndis with 8.34%. The fuzzy logic analysis afforded flexibility in prospecting for suitable areas for the installation of wood panel industries in the Espírito Santo State can bring great economic and social benefits to the local population with the generation of jobs, income, tax revenues and GDP increase for the State and municipalities involved. The proposed methodology can be adapted to other areas and agricultural crops. Copyright © 2017 Elsevier Ltd. All rights reserved.

Application issues for large-area electrochromic windows incommercial buildings

Energy Technology Data Exchange (ETDEWEB)

Lee, Eleanor S.; DiBartolomeo, D.L.

2000-05-01

Projections of performance from small-area devices to large-area windows and enterprise marketing have created high expectations for electrochromic glazings. As a result, this paper seeks to precipitate an objective dialog between material scientists and building-application scientists to determine whether actual large-area electrochromic devices will result in significant performance benefits and what material improvements are needed, if any, to make electrochromics more practical for commercial building applications. Few in-situ tests have been conducted with large-area electrochromic windows applied in buildings. This study presents monitored results from a full-scale field test of large-area electrochromic windows to illustrate how this technology will perform in commercial buildings. The visible transmittance (Tv) of the installed electrochromic ranged from 0.11 to 0.38. The data are limited to the winter period for a south-east-facing window. The effect of actual device performance on lighting energy use, direct sun control, discomfort glare, and interior illumination is discussed. No mechanical system loads were monitored. These data demonstrate the use of electrochromics in a moderate climate and focus on the most restrictive visual task: computer use in offices. Through this small demonstration, we were able to determine that electrochromic windows can indeed provide unmitigated transparent views and a level of dynamic illumination control never before seen in architectural glazing materials. Daily lighting energy use was 6-24 percent less compared to the 11 percent-glazing, with improved interior brightness levels. Daily lighting energy use was 3 percent less to 13 percent more compared to the 38 percent-glazing, with improved window brightness control. The electrochromic window may not be able to fulfill both energy-efficiency and visual comfort objectives when low winter direct sun is present, particularly for computer tasks using cathode-ray tube (CRT

Multimodality treatment of large AVMs in eloquent areas

International Nuclear Information System (INIS)

Inoue, Hiroshi K.; Naitou, Isao

2004-01-01

Our treatment of arteriovenous malformations (AVMs) with Gamma Knife Radiosurgery (optimal dose treatment) showed 88.4% total obliteration in small AVMs less than 10 ml after the first treatment and very low morbidity (1.7%) in long-term follow-up (5 to 12 years). These results indicate that combined treatment is a good strategy for large AVMs in eloquent areas. Therefore, we evaluated larger AVMs treated with direct surgery including feeder clipping and/or intravascular embolization prior to radiosurgery for further development of radiosurgery of large AVMs. Fifty of 171 patients had combined treatment (embolization: 27, direct surgery: 19, both: 4) and were followed more than 4 years and 6 months. Mean volume at the time of radiosurgery was smallest in the surgery group. Total obliteration was obtained in 94.4% of small AVMs less than 10 ml (surgery: 100%, embolization: 88.9%), although larger AVMs still have a lower obliteration rate. No lethal hemorrhages appeared after combination treatment up to date. We concluded that radiosurgery combined with surgery and/or embolization is a safe and effective treatment for large AVMs in eloquent areas. (author)

Design and assessment of urban drainage and water reuse systems for the reconstruction of formerly industrial areas: a case in Beijing.

Science.gov (United States)

Liu, L; Zeng, S; Dong, X; Chen, J

2013-01-01

The Shougang Group is an industrial steel enterprise occupying 800 ha in Beijing that will cease production by 2010. The area will be converted to a new financial and commercial zone. The rebuilding of the water infrastructure in this area should address water shortages in Beijing and retain the industrial landmark of a large cooling water tank. A design framework and an assessment system with 11 indicators were developed for this purpose. Four reconstruction schemes are presented here. Scheme 1 is a traditional system that completely depends on outside the municipal facility. Schemes 2, 3, and 4 are systems to separately discharge greywater and blackwater. Scheme 4 uses a vacuum system that allows the reclamation of nutrients. Schemes 2 and 4 use wetland-treated greywater to fill the water tank. Scheme 3 reuses greywater for toilets after on-site treatment. Scheme 2 is recommended due to its lower cost, greater environmental benefit, moderate resource reclamation, and higher technical feasibility.

NO2 and SO2 dispersion modeling and relative roles of emission sources over Map Ta Phut industrial area, Thailand.

Science.gov (United States)

Chusai, Chatinai; Manomaiphiboon, Kasemsan; Saiyasitpanich, Phirun; Thepanondh, Sarawut

2012-08-01

Map Ta Phut industrial area (MA) is the largest industrial complex in Thailand. There has been concern about many air pollutants over this area. Air quality management for the area is known to be difficult, due to lack of understanding of how emissions from different sources or sectors (e.g., industrial, power plant, transportation, and residential) contribute to air quality degradation in the area. In this study, a dispersion study of NO2 and SO2 was conducted using the AERMOD model. The area-specific emission inventories of NOx and SO2 were prepared, including both stack and nonstack sources, and divided into 11 emission groups. Annual simulations were performed for the year 2006. Modeled concentrations were evaluated with observations. Underestimation of both pollutants was Jbund, and stack emission estimates were scaled to improve the modeled results before quantifying relative roles of individual emission groups to ambient concentration overfour selected impacted areas (two are residential and the others are highly industrialized). Two concentration measures (i.e., annual average area-wide concentration or AC, and area-wide robust highest concentration or AR) were used to aggregately represent mean and high-end concentrations Jbfor each individual area, respectively. For AC-NO2, on-road mobile emissions were found to be the largest contributor in the two residential areas (36-38% of total AC-NO2), while petrochemical-industry emissions play the most important role in the two industrialized areas (34-51%). For AR-NO2, biomass burning has the most influence in all impacted areas (>90%) exceptJor one residential area where on-road mobile is the largest (75%). For AC-SO2, the petrochemical industry contributes most in all impacted areas (38-56%). For AR-SO2, the results vary. Since the petrochemical industry was often identified as the major contributor despite not being the largest emitter, air quality workers should pay special attention to this emission group

Optimization of large-scale industrial systems : an emerging method

Energy Technology Data Exchange (ETDEWEB)

Hammache, A.; Aube, F.; Benali, M.; Cantave, R. [Natural Resources Canada, Varennes, PQ (Canada). CANMET Energy Technology Centre

2006-07-01

This paper reviewed optimization methods of large-scale industrial production systems and presented a novel systematic multi-objective and multi-scale optimization methodology. The methodology was based on a combined local optimality search with global optimality determination, and advanced system decomposition and constraint handling. The proposed method focused on the simultaneous optimization of the energy, economy and ecology aspects of industrial systems (E{sup 3}-ISO). The aim of the methodology was to provide guidelines for decision-making strategies. The approach was based on evolutionary algorithms (EA) with specifications including hybridization of global optimality determination with a local optimality search; a self-adaptive algorithm to account for the dynamic changes of operating parameters and design variables occurring during the optimization process; interactive optimization; advanced constraint handling and decomposition strategy; and object-oriented programming and parallelization techniques. Flowcharts of the working principles of the basic EA were presented. It was concluded that the EA uses a novel decomposition and constraint handling technique to enhance the Pareto solution search procedure for multi-objective problems. 6 refs., 9 figs.

Quality index of the surface water of Amazonian rivers in industrial areas in Pará, Brazil.

Science.gov (United States)

Medeiros, Adaelson Campelo; Faial, Kleber Raimundo Freitas; do Carmo Freitas Faial, Kelson; da Silva Lopes, Iris Danielly; de Oliveira Lima, Marcelo; Guimarães, Raphael Mendonça; Mendonça, Neyson Martins

2017-10-15

In this study was to evaluate the waters quality of the Murucupi River, located in urban agglomerate area and intense industrial activity in Barcarena City, Pará State. The Arapiranga River in Abaetetuba City was used as control area (Background), next to Barcarena. Was used the Water Quality Index (WQI) based on nine variables analized. Waters quality of the Arapiranga and Murucupi rivers were regular to good and bad to good, respectively. Anthropogenic influence on the Murucupi River was higher, mainly by the disposal of domestic effluents from the urban agglomerate and of the industrial waste tailing basins upstream of this river. Due to its less inhabited environment and further away from the area urban and industrial, the Arapiranga River was more preserved. Waters pollution of around these area is increasingly intense, and restricted its uses for various purposes. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Simulations of Large-Area Electron Beam Diodes

Science.gov (United States)

Swanekamp, S. B.; Friedman, M.; Ludeking, L.; Smithe, D.; Obenschain, S. P.

1999-11-01

Large area electron beam diodes are typically used to pump the amplifiers of KrF lasers. Simulations of large-area electron beam diodes using the particle-in-cell code MAGIC3D have shown the electron flow in the diode to be unstable. Since this instability can potentially produce a non-uniform current and energy distribution in the hibachi structure and lasing medium it can be detrimental to laser efficiency. These results are similar to simulations performed using the ISIS code.(M.E. Jones and V.A. Thomas, Proceedings of the 8^th) International Conference on High-Power Particle Beams, 665 (1990). We have identified the instability as the so called ``transit-time" instability(C.K. Birdsall and W.B. Bridges, Electrodynamics of Diode Regions), (Academic Press, New York, 1966).^,(T.M. Antonsen, W.H. Miner, E. Ott, and A.T. Drobot, Phys. Fluids 27), 1257 (1984). and have investigated the role of the applied magnetic field and diode geometry. Experiments are underway to characterize the instability on the Nike KrF laser system and will be compared to simulation. Also some possible ways to mitigate the instability will be presented.

Roll-to-roll hot embossing system with shape preserving mechanism for the large-area fabrication of microstructures

Science.gov (United States)

Peng, Linfa; Wu, Hao; Shu, Yunyi; Yi, Peiyun; Deng, Yujun; Lai, Xinmin

2016-10-01

Roll-to-roll (R2R) hot embossing is a promising approach to fulfilling the demands of high throughput fabrication of large-area polymeric components with micro-structure arrays which have been widely employed in the domains of optics, optoelectronics, biology, chemistry, etc. Nevertheless, the characteristic of continuous and fast forming for the R2R hot embossing process limits material flow during filling stage and results in significant springback during demolding stage. As a result, forming defects usually appear and the process window is very narrow which hinders the industrialization of this technology. This study developed a R2R hot embossing machine and proposed a shape preserving mechanism to extend the material filling time and realized the cooling effect during the demolding process. Comparative experiments were conducted on the R2R hot embossing process for micro-pyramid arrays to understand the effect of shape preserving mechanism. The influence of tension force and encapsulation angle to the forming quality was systematically analyzed. Furthermore, the influence of processing parameters has been investigated by using the one-variable-at-a-time method. Afterwards, a series of experiments based on the central composite design approach have been conducted for the analysis of variance and the establishment of empirical models of the R2R hot embossing process. As a result, the process window was extended by the shape preserving mechanism. More importantly, the feeding speed was improved from 0.5 m min-1 to 2.5 m min-1 for the large-area fabrication of micro-pyramid arrays, which is very attractive to the industrialization of this technology.

Nanotechnological Advances in Catalytic Thin Films for Green Large-Area Surfaces

Directory of Open Access Journals (Sweden)

Suzan Biran Ay

2015-01-01

Full Text Available Large-area catalytic thin films offer great potential for green technology applications in order to save energy, combat pollution, and reduce global warming. These films, either embedded with nanoparticles, shaped with nanostructuring techniques, hybridized with other systems, or functionalized with bionanotechnological methods, can include many different surface properties including photocatalytic, antifouling, abrasion resistant and mechanically resistive, self-cleaning, antibacterial, hydrophobic, and oleophobic features. Thus, surface functionalization with such advanced structuring methods is of significance to increase the performance and wide usage of large-area thin film coatings specifically for environmental remediation. In this review, we focus on methods to increase the efficiency of catalytic reactions in thin film and hence improve the performance in relevant applications while eliminating high cost with the purpose of widespread usage. However, we also include the most recent hybrid architectures, which have potential to make a transformational change in surface applications as soon as high quality and large area production techniques are available. Hence, we present and discuss research studies regarding both organic and inorganic methods that are used to structure thin films that have potential for large-area and eco-friendly coatings.

Thin absorbers for large-area soft X-ray microcalorimeters

Energy Technology Data Exchange (ETDEWEB)

Rocks, L. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States)]. E-mail: rocks@wisp.physics.wisc.edu; Anderson, M.B. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Bilgri, N. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Brekosky, R. [NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Gwynne Crowder, S. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Figueroa-Feliciano, E. [NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Kelley, R. [NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Kilbourne, C.A. [NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Lai, T. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Lindeman, M.A. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Man, J. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); McCammon, D. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Nelms, K.L. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Porter, F.S. [NASA/Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Sivananthan, S. [University of Illinois at Chicago, Chicago, IL 60607 (United States); Vidugiris, G. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Zhao, J. [University of Illinois at Chicago, Chicago, IL 60607 (United States)

2006-04-15

The X-ray Quantum Calorimeter (XQC) sounding rocket experiment utilizes a microcalorimeter array for observing the diffuse soft X-ray background. Observations of such low surface-brightness targets require a large-area detector. We will be using an array of large absorbers. Good absorbers must rapidly and completely thermalize photons, have small heat capacity for high stopping efficiency and have good lateral thermal transport. For observing the soft X-ray background (energies <1 keV), the volume and heat capacity of absorber material can be kept to a minimum by making the absorbers only as thick as needed for high quantum efficiency at these low energies. These thin, large-area absorbers are not self-supporting and have poor lateral heat transport. Depositing the absorber material on a Si substrate provides support and improves lateral thermal conduction. We present heat capacity results for thin HgTe and thin Bi, each on Si substrates. We also describe the HgTe absorber fabrication.

Dark Matter Searches with the Fermi Large Area Telescope

International Nuclear Information System (INIS)

Meurer, Christine

2008-01-01

The Fermi Gamma-Ray Space Telescope, successfully launched on June 11th, 2008, is the next generation satellite experiment for high-energy gamma-ray astronomy. The main instrument, the Fermi Large Area Telescope (LAT), with a wide field of view (>2 sr), a large effective area (>8000 cm 2 at 1 GeV), sub-arcminute source localization, a large energy range (20 MeV-300 GeV) and a good energy resolution (close to 8% at 1 GeV), has excellent potential to either discover or to constrain a Dark Matter signal. The Fermi LAT team pursues complementary searches for signatures of particle Dark Matter in different search regions such as the galactic center, galactic satellites and subhalos, the milky way halo, extragalactic regions as well as the search for spectral lines. In these proceedings we examine the potential of the LAT to detect gamma-rays coming from Weakly Interacting Massive Particle annihilations in these regions with special focus on the galactic center region.

Development of sub-nanosecond, high gain structures for time-of-flight ring imaging in large area detectors

International Nuclear Information System (INIS)

Wetstein, Matthew

2011-01-01

Microchannel plate photomultiplier tubes (MCPs) are compact, imaging detectors, capable of micron-level spatial imaging and timing measurements with resolutions below 10 ps. Conventional fabrication methods are too expensive for making MCPs in the quantities and sizes necessary for typical HEP applications, such as time-of-flight ring-imaging Cherenkov detectors (TOF-RICH) or water Cherenkov-based neutrino experiments. The Large Area Picosecond Photodetector Collaboration (LAPPD) is developing new, commercializable methods to fabricate 20 cm 2 thin planar MCPs at costs comparable to those of traditional photo-multiplier tubes. Transmission-line readout with waveform sampling on both ends of each line allows the efficient coverage of large areas while maintaining excellent time and space resolution. Rather than fabricating channel plates from active, high secondary electron emission materials, we produce plates from passive substrates, and coat them using atomic layer deposition (ALD), a well established industrial batch process. In addition to possible reductions in cost and conditioning time, this allows greater control to optimize the composition of active materials for performance. We present details of the MCP fabrication method, preliminary results from testing and characterization facilities, and possible HEP applications.

Occupation and lung cancer in two industrialized areas of northern Italy

Energy Technology Data Exchange (ETDEWEB)

Ronco, G.; Ciccone, G.; Mirabelli, D.; Troia, B.; Vineis, P.

1988-03-15

A population-based case-control study on lung cancer was conducted in 2 industrialized areas of northern Italy. Cases (126) were all males who died from lung cancer between 1976 and 1980. Controls (384) were a random sample of males dying from other causes during the same period. Jobs held during working life have been analyzed according to a list of occupations already known to be causally associated with lung cancer (list A) and a list of occupations suspected of being so (list B). Attributable risk percentages in the population for occupations included in either list A or B were about 36% and 12% in the 2 areas. Welders or workers in industries in which welding is common showed elevated odds ratios: 2.9 for welders (95% CI 0.9-9.8); 4.9 (1.1-22.9) for structural metal workers; 11.4 (2.6-49.9) for workers in structural metal production. Other job categories associated with lung cancer included: electricians and workers in electrical machine production, woodworkers (in furniture or cabinet making, but not in carpentry or joinery) and cleaning services. Smoking did not seem to exert a substantial confounding effect. Attributable risk percentages for tobacco smoking were about 78% and 76% in the population of the 2 areas.

Occupation and lung cancer in two industrialized areas of northern Italy.

Science.gov (United States)

Ronco, G; Ciccone, G; Mirabelli, D; Troia, B; Vineis, P

1988-03-15

A population-based case-control study on lung cancer was conducted in 2 industrialized areas of northern Italy. Cases (126) were all males who died from lung cancer between 1976 and 1980. Controls (384) were a random sample of males dying from other causes during the same period. Jobs held during working life have been analyzed according to a list of occupations already known to be causally associated with lung cancer (list A) and a list of occupations suspected of being so (list B). Attributable risk percentages in the population for occupations included in either list A or B were about 36% and 12% in the 2 areas. Welders or workers in industries in which welding is common showed elevated odds ratios: 2.9 for welders (95% CI 0.9-9.8); 4.9 (1.1-22.9) for structural metal workers; 11.4 (2.6-49.9) for workers in structural metal production. Other job categories associated with lung cancer included: electricians and workers in electrical machine production, woodworkers (in furniture or cabinet making, but not in carpentry or joinery) and cleaning services. Smoking did not seem to exert a substantial confounding effect. Attributable risk percentages for tobacco smoking were about 78% and 76% in the population of the 2 areas.

Energy Conservation Projects to Benefit the Railroad Industry

Energy Technology Data Exchange (ETDEWEB)

Clifford Mirman; Promod Vohra

2009-12-31

The Energy Conservation Projects to benefit the railroad industry using the Norfolk Southern Company as a model for the railroad industry has five unique tasks which are in areas of importance within the rail industry, and specifically in the area of energy conservation. The NIU Engineering and Technology research team looked at five significant areas in which research and development work can provide unique solutions to the railroad industry in energy the conservation. (1) Alternate Fuels - An examination of various blends of bio-based diesel fuels for the railroad industry, using Norfolk Southern as a model for the industry. The team determined that bio-diesel fuel is a suitable alternative to using straight diesel fuel, however, the cost and availability across the country varies to a great extent. (2) Utilization of fuel cells for locomotive power systems - While the application of the fuel cell has been successfully demonstrated in the passenger car, this is a very advanced topic for the railroad industry. There are many safety and power issues that the research team examined. (3) Thermal and emission reduction for current large scale diesel engines - The current locomotive system generates large amount of heat through engine cooling and heat dissipation when the traction motors are used to decelerate the train. The research team evaluated thermal management systems to efficiently deal with large thermal loads developed by the operating engines. (4) Use of Composite and Exotic Replacement Materials - Research team redesigned various components using new materials, coatings, and processes to provide the needed protection. Through design, analysis, and testing, new parts that can withstand the hostile environments were developed. (5) Tribology Applications - Identification of tribology issues in the Railroad industry which play a significant role in the improvement of energy usage. Research team analyzed and developed solutions which resulted in friction

The GLAST Large Area Telescope Detector Performance Monitoring

International Nuclear Information System (INIS)

Borgland, A.W.; Charles, E.; SLAC

2007-01-01

The Large Area Telescope (LAT) is one of two instruments on board the Gamma-ray Large Area Telescope (GLAST), the next generation high energy gamma-ray space telescope. The LAT contains sixteen identical towers in a four-by-four grid. Each tower contains a silicon-strip tracker and a CsI calorimeter that together will give the incident direction and energy of the pair-converting photon in the energy range 20 MeV - 300 GeV. In addition, the instrument is covered by a finely segmented Anti-Coincidence Detector (ACD) to reject charged particle background. Altogether, the LAT contains more than 864k channels in the trackers, 1536 CsI crystals and 97 ACD plastic scintillator tiles and ribbons. Here we detail some of the strategies and methods for how we are planning to monitor the instrument performance on orbit. It builds on the extensive experience gained from Integration and Test and Commissioning of the instrument on ground

Technique investigation on large area neutron scintillation detector array

International Nuclear Information System (INIS)

Chen Jiabin

2006-12-01

The detailed project for developing Large Area Neutron Scintillation Detector Array (LaNSA) to be used for measuring fusion fuel area density on Shenguang III prototype is presented, including experimental principle, detector working principle, electronics system design and the needs for target chamber etc. The detailed parameters for parts are given and the main causes affecting the system function are analyzed. The realization path is introduced. (authors)

Fabrication of large area flexible nanoplasmonic templates with flow coating

Science.gov (United States)

Huang, Qian; Devetter, Brent M.; Roosendaal, Timothy; LaBerge, Max; Bernacki, Bruce E.; Alvine, Kyle J.

2017-07-01

We describe the development of a custom-built two-axis flow coater for the deposition of polymeric nanosphere monolayers that could be used in the fabrication of large area nanoplasmonic films. The technique described here has the capability of depositing large areas (up to 7 in. × 10 in.) of self-assembled monolayers of polymeric nanospheres onto polyethylene terephthalate (PET) films. Here, three sets of films consisting of different diameters (ranging from 100 to 300 nm) of polymeric nanospheres were used to demonstrate the capabilities of this instrument. To improve the surface wettability of the PET substrates during wet-deposition, we enhanced the wettability by using a forced air blown-arc plasma treatment system. Both the local microstructure, as confirmed by scanning electron microscopy, describing monolayer and multilayer coverage, and the overall macroscopic uniformity of the resultant nanostructured film were optimized by controlling the relative stage to blade speed and nanosphere concentration. We also show using a smaller nanoparticle template that such monolayers can be used to form nanoplasmonic films. As this flow-coating approach is a scalable technique, large area films such as the ones described here have a variety of crucial emerging applications in areas such as energy, catalysis, and chemical sensing.

Experimental study on generation of large area uniform electron beam

International Nuclear Information System (INIS)

Tang Ying; Yi Aiping; Liu Jingru; Qian Hang; Huang Xin; Yu Li; Su Jiancang; Ding Zhenjie; Ding Yongzhong; Yu Jianguo

2007-01-01

In the experiment of gas laser pumped by electron beam, large area uniform electron beam is important to generate high efficiency laser output. The experimental study on generation of large area uniform electron beam with SPG-200 pulsed power generator is introduced. SPG-200 is an all-solid-state components pulsed power generator based on SOS, and its open voltage is more than 350 kV. The cathode have the area of 24 mm x 294 mm, and the anode-cathode(A-C)gap spacing is adjustable from 0 to 49 mm. The electron beam of cathode emission is transported to the laser chamber through the diode pressure foil, which sepa-rates the vacuum chamber from the laser chamber. Velvet and graphite cathodes are studied, each generates large area electron beam. The diode parameters are presented, and the uniformity of e-beam is diagnosed. The experimental results show that the diode voltage of the graphite cathode is 240-280 kV, and the diode current is 0.7-1.8 kA. The diode voltage of the velvet cathode is 200-250 kV, and the diode current is 1.5-1.7 kA. The uniformity of the velvet cathode emission is better than that of the graphite cathode. (authors)

Large-area photogrammetry based testing of wind turbine blades

Science.gov (United States)

Poozesh, Peyman; Baqersad, Javad; Niezrecki, Christopher; Avitabile, Peter; Harvey, Eric; Yarala, Rahul

2017-03-01

An optically based sensing system that can measure the displacement and strain over essentially the entire area of a utility-scale blade leads to a measurement system that can significantly reduce the time and cost associated with traditional instrumentation. This paper evaluates the performance of conventional three dimensional digital image correlation (3D DIC) and three dimensional point tracking (3DPT) approaches over the surface of wind turbine blades and proposes a multi-camera measurement system using dynamic spatial data stitching. The potential advantages for the proposed approach include: (1) full-field measurement distributed over a very large area, (2) the elimination of time-consuming wiring and expensive sensors, and (3) the need for large-channel data acquisition systems. There are several challenges associated with extending the capability of a standard 3D DIC system to measure entire surface of utility scale blades to extract distributed strain, deflection, and modal parameters. This paper only tries to address some of the difficulties including: (1) assessing the accuracy of the 3D DIC system to measure full-field distributed strain and displacement over the large area, (2) understanding the geometrical constraints associated with a wind turbine testing facility (e.g. lighting, working distance, and speckle pattern size), (3) evaluating the performance of the dynamic stitching method to combine two different fields of view by extracting modal parameters from aligned point clouds, and (4) determining the feasibility of employing an output-only system identification to estimate modal parameters of a utility scale wind turbine blade from optically measured data. Within the current work, the results of an optical measurement (one stereo-vision system) performed on a large area over a 50-m utility-scale blade subjected to quasi-static and cyclic loading are presented. The blade certification and testing is typically performed using International

ArCLight—A Compact Dielectric Large-Area Photon Detector

Directory of Open Access Journals (Sweden)

Martin Auger

2018-02-01

Full Text Available ArgonCube Light readout system (ArCLight is a novel device for detecting scintillation light over large areas with Photon Detection Efficiency (PDE of the order of a few percent. Its robust technological design allows for efficient use in large-volume particle detectors, such as Liquid Argon Time Projection Chambers (LArTPCs or liquid scintillator detectors. Due to its dielectric structure it can be placed inside volumes with high electric field. It could potentially replace vacuum PhotoMultiplier Tubes (PMTs in applications where high PDE is not required. The photon detection efficiency for a 10 × 10 cm2 detector prototype was measured to be in the range of 0.8% to 2.2% across the active area.

Large-Area Visually Augmented Navigation for Autonomous Underwater Vehicles

National Research Council Canada - National Science Library

Eustice, Ryan M

2005-01-01

...., unstructured terrain, low-overlap imagery, moving light source). Our large area SLAM algorithm recursively incorporates relative-pose constraints using a view-based representation that exploits exact sparsity in the Gaussian canonical...

Discrimination of Settlement and Industrial Area Using Landscape Metrics in Rural Region

Directory of Open Access Journals (Sweden)

Xinyu Zheng

2016-10-01

Full Text Available Detailed and precise information of land-use and land-cover (LULC in rural area is essential for land-use planning, environment and energy management. The confusion in mapping residential and industrial areas brings problems in energy management, environmental management and sustainable land use development. However, they remain ambiguous in the former rural LULC mapping, and this insufficient supervision leads to inefficient land exploitation and a great waste of land resources. Hence, the extent and area of residential and industrial cover need to be revealed urgently. However, spectral and textural information is not sufficient for classification heterogeneity due to the similarity between different LULC types. Meanwhile, the contextual information about the relationship between a LULC feature and its surroundings still has potential in classification application. This paper attempts to discriminate settlement and industry area using landscape metrics. A feasible classification scheme integrating landscape metrics, chessboard segmentation and object-based image analysis (OBIA is proposed. First LULC map is generated from GeoEye-1 image, which delineated distribution of different land-cover materials using traditional OBIA method with spectrum and texture information. Then, a chessboard segmentation of the whole LULC map is conducted to create landscape units in a uniform spatial area. Landscape characteristics in each square of chessboard are adopted in the classification algorithm subsequently. To analyze landscape unit scale effect, a variety of chessboard scales are tested, with overall accuracy ranging from 75% to 88%, and Kappa coefficient from 0.51 to 0.76. Optimal chessboard scale is obtained through accuracy assessment comparison. This classification scheme is then compared to two other approaches: a top-down hierarchical classification network using only spectral, textural and shape properties, and lacunarity based hierarchical

Very large area multiwire spectroscopic proportional counters

International Nuclear Information System (INIS)

Ubertini, P.; Bazzano, A.; Boccaccini, L.; Mastropietro, M.; La Padula, C.D.; Patriarca, R.; Polcaro, V.F.

1981-01-01

As a result of a five year development program, a final prototype of a Very Large Area Spectroscopic Proportional Counter (VLASPC), to be employed in space borne payloads, was produced at the Istituto di Astrofisica Spaziale, Frascati. The instrument is the last version of a new generation of Multiwire Spectroscopic Proportional Counters (MWSPC) succesfully employed in many balloon borne flights, devoted to hard X-ray astronomy. The sensitive area of this standard unit is 2700 cm 2 with an efficiency higher than 10% in the range 15-180 keV (80% at 60 keV). The low cost and weight make this new type of VLASPC competitive with Nal arrays, phoswich and GSPC detectors in terms of achievable scientific results. (orig.)

Very large area multiwire spectroscopic proportional counters

Energy Technology Data Exchange (ETDEWEB)

Ubertini, P.; Bazzano, A.; Boccaccini, L.; Mastropietro, M.; La Padula, C.D.; Patriarca, R.; Polcaro, V.F. (Istituto di Astrofisica Spaziale, Frascati (Italy))

1981-07-01

As a result of a five year development program, a final prototype of a Very Large Area Spectroscopic Proportional Counter (VLASPC), to be employed in space borne payloads, was produced at the Istituto di Astrofisica Spaziale, Frascati. The instrument is the last version of a new generation of Multiwire Spectroscopic Proportional Counters (MWSPC) successfully employed in many balloon borne flights, devoted to hard X-ray astronomy. The sensitive area of this standard unit is 2700 cm/sup 2/ with an efficiency higher than 10% in the range 15-180 keV (80% at 60 keV). The low cost and weight make this new type of VLASPC competitive with Nal arrays, phoswich and GSPC detectors in terms of achievable scientific results.

The Feasibility of Small Hydro-Electric Generation in a Large Urban Area

OpenAIRE

Benson Y. Zhang; Adam Taylor

2012-01-01

The possibilities of generating electric power from relatively small hydro-electric sources in a large urban area is investigated. Two different aspects of hydro-electric sources have been studied: storm/waste water pipes in large multi-tenanted residential buildings and urban storm water discharge area (CSI area). The potential to generate from these sources has been investigated using a micro-turbine. The potential electric power which could be extracted from the sources was estimated using...

A Brief Technical History of the Large-Area Picosecond Photodetector (LAPPD) Collaboration

Energy Technology Data Exchange (ETDEWEB)

Adams, B.W.; et al.

2016-03-06

The Large Area Picosecond PhotoDetector (LAPPD) Collaboration was formed in 2009 to develop large-area photodetectors capable of time resolutions measured in pico-seconds, with accompanying sub-millimeter spatial resolution. During the next three and one-half years the Collaboration developed the LAPPD design of 20 x 20 cm modules with gains greater than $10^7$ and non-uniformity less than $15\\%$, time resolution less than 50 psec for single photons and spatial resolution of 700~microns in both lateral dimensions. We describe the R\\&D performed to develop large-area micro-channel plate glass substrates, resistive and secondary-emitting coatings, large-area bialkali photocathodes, and RF-capable hermetic packaging. In addition, the Collaboration developed the necessary electronics for large systems capable of precise timing, built up from a custom low-power 15-GigaSample/sec waveform sampling 6-channel integrated circuit and supported by a two-level modular data acquisition system based on Field-Programmable Gate Arrays for local control, data-sparcification, and triggering. We discuss the formation, organization, and technical successes and short-comings of the Collaboration. The Collaboration ended in December 2012 with a transition from R\\&D to commercialization.

Emergy-based comparative analysis on industrial clusters: economic and technological development zone of Shenyang area, China.

Science.gov (United States)

Liu, Zhe; Geng, Yong; Zhang, Pan; Dong, Huijuan; Liu, Zuoxi

2014-09-01

In China, local governments of many areas prefer to give priority to the development of heavy industrial clusters in pursuit of high value of gross domestic production (GDP) growth to get political achievements, which usually results in higher costs from ecological degradation and environmental pollution. Therefore, effective methods and reasonable evaluation system are urgently needed to evaluate the overall efficiency of industrial clusters. Emergy methods links economic and ecological systems together, which can evaluate the contribution of ecological products and services as well as the load placed on environmental systems. This method has been successfully applied in many case studies of ecosystem but seldom in industrial clusters. This study applied the methodology of emergy analysis to perform the efficiency of industrial clusters through a series of emergy-based indices as well as the proposed indicators. A case study of Shenyang Economic Technological Development Area (SETDA) was investigated to show the emergy method's practical potential to evaluate industrial clusters to inform environmental policy making. The results of our study showed that the industrial cluster of electric equipment and electronic manufacturing produced the most economic value and had the highest efficiency of energy utilization among the four industrial clusters. However, the sustainability index of the industrial cluster of food and beverage processing was better than the other industrial clusters.

Seafloor mapping of large areas using multibeam system - Indian experience

Digital Repository Service at National Institute of Oceanography (India)

Kodagali, V.N.; KameshRaju, K.A; Ramprasad, T.

averaged and merged to produce large area maps. Maps were generated in the scale of 1 mil. and 1.5 mil covering area of about 2 mil. sq.km in single map. Also, depth contour interval were generated. A computer program was developed to convert the depth data...

Activity of CERN and LNF groups on large area GEM detectors

Energy Technology Data Exchange (ETDEWEB)

Alfonsi, M. [CERN, Geneva (Switzerland); Bencivenni, G. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Brock, I. [Physikalisches Institute der Universitat Bonn, Bonn (Germany); Cerioni, S. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Croci, G.; David, E. [CERN, Geneva (Switzerland); De Lucia, E. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); De Oliveira, R. [CERN, Geneva (Switzerland); De Robertis, G. [Sezione INFN di Bari, Bari (Italy); Domenici, D., E-mail: Danilo.Domenici@lnf.infn.i [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Duarte Pinto, S. [CERN, Geneva (Switzerland); Felici, G.; Gatta, M.; Jacewicz, M. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Loddo, F. [Sezione INFN di Bari, Bari (Italy); Morello, G. [Dipeartimento di Fisica Universita della Calabria e INFN, Cosenza (Italy); Pistilli, M. [Laboratori Nazionali di Frascati dell' INFN, Frascati (Italy); Ranieri, A. [Sezione INFN di Bari, Bari (Italy); Ropelewski, L. [CERN, Geneva (Switzerland); Sauli, F. [TERA Foundation, Novara (Italy)

2010-05-21

We report on the activity of CERN and INFN-LNF groups on the development of large area GEM detectors. The two groups work together within the RD51 Collaboration, to aim at the development of Micro-pattern Gas detectors technologies. The vast request for large area foils by the GEM community has driven a change in the manufacturing procedure by the TS-DEM-PMT laboratory, needed to overcome the previous size limitation of 450x450mm{sup 2}. Now a single-mask technology is used allowing foils to be made as large as 450x2000mm{sup 2}. The limitation in the short size, due to the definite width of the raw material, can be overcome by splicing more foils together. A 10x10cm{sup 2} GEM detector with the new single-mask foil has been tested with X-rays and the results are shown. Possible future applications for large area GEM are the TOTEM experiment upgrade at CERN, and the KLOE-2 experiment at the Dafne {Phi}-factory in Frascati.

Activity of CERN and LNF groups on large area GEM detectors

International Nuclear Information System (INIS)

Alfonsi, M.; Bencivenni, G.; Brock, I.; Cerioni, S.; Croci, G.; David, E.; De Lucia, E.; De Oliveira, R.; De Robertis, G.; Domenici, D.; Duarte Pinto, S.; Felici, G.; Gatta, M.; Jacewicz, M.; Loddo, F.; Morello, G.; Pistilli, M.; Ranieri, A.; Ropelewski, L.; Sauli, F.

2010-01-01

We report on the activity of CERN and INFN-LNF groups on the development of large area GEM detectors. The two groups work together within the RD51 Collaboration, to aim at the development of Micro-pattern Gas detectors technologies. The vast request for large area foils by the GEM community has driven a change in the manufacturing procedure by the TS-DEM-PMT laboratory, needed to overcome the previous size limitation of 450x450mm 2 . Now a single-mask technology is used allowing foils to be made as large as 450x2000mm 2 . The limitation in the short size, due to the definite width of the raw material, can be overcome by splicing more foils together. A 10x10cm 2 GEM detector with the new single-mask foil has been tested with X-rays and the results are shown. Possible future applications for large area GEM are the TOTEM experiment upgrade at CERN, and the KLOE-2 experiment at the Dafne Φ-factory in Frascati.

Rabi-like splitting from large area plasmonic microcavity

Directory of Open Access Journals (Sweden)

Fatemeh Hosseini Alast

2017-08-01

Full Text Available Rabi-like splitting was observed from a hybrid plasmonic microcavity. The splitting comes from the coupling of cavity mode with the surface plasmon polariton mode; anti-crossing was observed alongside the modal conversional channel on the reflection light measurement. The hybrid device consists of a 10x10 mm2 ruled metal grating integrated onto the Fabry-Perot microcavity. The 10x10 mm2 ruled metal grating fabricated from laser interference and the area is sufficiently large to be used in the practical optical device. The larger area hybrid plasmonic microcavity can be employed in polariton lasers and biosensors.

Monitoring persistent organic pollutants in an industrial area of Tarragona (Catalonia, Spain)

Energy Technology Data Exchange (ETDEWEB)

Nadal, M.; Schuhmacher, M.; Domingo, J.L. [Rovira i Virgili University, Reus (Spain)

2004-09-15

It is well known that combustion of different materials is one of the most important sources of environmental contamination by persistent organic pollutants (POPs). Therefore, environments affected by this kind of processes should be strictly controlled. In relation to it, the 2001 Stockholm Convention for the regulation of POPs was undertaken in order to establish agreements and mechanisms to erase the release of 12 POPs on a global scale. While polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) and polychlorinated biphenyls (PCBs) were included in this list, other pollutants such as polychlorinated naphthalenes (PCNs) and polycyclic aromatic hydrocarbons (PAHs) can be added in a near future. Since more than 30 years ago, one of the largest chemical and petrochemical industrial complexes in Southern Europe is located in Tarragona County (Catalonia, Spain). Several chemical industries (such as a PVC production facility and a chlor-alkali plant) and a big oil refinery are located in this residential area (up to 300,000 inhabitants), together with a municipal solid waste incinerator (MSWI) and a hazardous waste incinerator (HWI). Moreover, the presence of a highway and several roads with an important traffic density influences also the environment of the zone. The current study is a preliminary investigation to assess the levels of several POPs (PCDD/Fs, PCBs, PCNs and PAHs) in soil and vegetation samples collected in Tarragona's industrial and residential areas and to compare them with data obtained in unpolluted sites as well as in other industrial and residential zones.

Mono and multi-objective optimization techniques applied to a large range of industrial test cases using Metamodel assisted Evolutionary Algorithms

Science.gov (United States)

Fourment, Lionel; Ducloux, Richard; Marie, Stéphane; Ejday, Mohsen; Monnereau, Dominique; Massé, Thomas; Montmitonnet, Pierre

2010-06-01

The use of material processing numerical simulation allows a strategy of trial and error to improve virtual processes without incurring material costs or interrupting production and therefore save a lot of money, but it requires user time to analyze the results, adjust the operating conditions and restart the simulation. Automatic optimization is the perfect complement to simulation. Evolutionary Algorithm coupled with metamodelling makes it possible to obtain industrially relevant results on a very large range of applications within a few tens of simulations and without any specific automatic optimization technique knowledge. Ten industrial partners have been selected to cover the different area of the mechanical forging industry and provide different examples of the forming simulation tools. It aims to demonstrate that it is possible to obtain industrially relevant results on a very large range of applications within a few tens of simulations and without any specific automatic optimization technique knowledge. The large computational time is handled by a metamodel approach. It allows interpolating the objective function on the entire parameter space by only knowing the exact function values at a reduced number of "master points". Two algorithms are used: an evolution strategy combined with a Kriging metamodel and a genetic algorithm combined with a Meshless Finite Difference Method. The later approach is extended to multi-objective optimization. The set of solutions, which corresponds to the best possible compromises between the different objectives, is then computed in the same way. The population based approach allows using the parallel capabilities of the utilized computer with a high efficiency. An optimization module, fully embedded within the Forge2009 IHM, makes possible to cover all the defined examples, and the use of new multi-core hardware to compute several simulations at the same time reduces the needed time dramatically. The presented examples

Isocyanatocyclohexane and isothiocyanatocyclohexane levels in urban and industrial areas and possible emission-related activities

Science.gov (United States)

Gallego, E.; Roca, F. X.; Perales, F.; Ribes, A.; Carrera, G.; Guardino, X.; Berenguer, M. J.

Isocyanatocyclohexane and isothiocyanatocyclohexane are becoming relevant compounds in urban and industrial air, as they are used in important amounts in automobile industry and building insulation, as well as in the manufacture of foams, rubber, paints and varnishes. Glass multi-sorbent tubes (Carbotrap, Carbopack, Carboxen) were connected to LCMA-UPC pump samplers for the retention of iso- and isothiocyanatocyclohexanes. The analysis was performed by automatic thermal desorption (ATD) coupled with capillary gas chromatography (GC)/mass spectrometry detector (MSD). TD-GC/MS was chosen as analytical method due to its versatility and the possibility of analysis of a wide range of volatility and polarity VOC in air samples. The method was satisfactory sensitive, selective and reproducible for the studied compounds. The concentrations of iso- and isothioisocyanatocyclohexanes were evaluated in different urban, residential and industrial locations from extensive VOC air quality and odour episode studies in several cities in the Northeastern edge of Spain. Around 200-300 VOC were determined qualitatively in each sample. Higher values of iso- and isothiocyanatocyclohexane were found in industrial areas than in urban or residential locations. The concentrations ranged between n.d.-246 and n.d.-29 μg m -3 for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively, for industrial areas. On the other hand, urban and residential locations showed concentrations ranging between n.d.-164 and n.d.-29 μg m -3 for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively. The site location (urban or industrial), the kind and nearness of possible iso- and isothiocyanatocyclohexane emission activities (industrial or building construction) and the changes of wind regimes throughout the year have been found the most important factors influencing the concentrations of these compounds in the different places.

The Anti-Coincidence Detector for the GLAST Large Area Telescope

Energy Technology Data Exchange (ETDEWEB)

Moiseev, A.A.; Hartman, R.C.; Ormes, J.F.; Thompson, D.J.; Amato, M.J.; Johnson, T.E.; Segal, K.N.; Sheppard, D.A.

2007-03-23

This paper describes the design, fabrication and testing of the Anti-Coincidence Detector (ACD) for the Gamma-ray Large Area Space Telescope (GLAST) Large Area Telescope (LAT). The ACD is LAT's first-level defense against the charged cosmic ray background that outnumbers the gamma rays by 3-5 orders of magnitude. The ACD covers the top and 4 sides of the LAT tracking detector, requiring a total active area of {approx}8.3 square meters. The ACD detector utilizes plastic scintillator tiles with wave-length shifting fiber readout. In order to suppress self-veto by shower particles at high gamma-ray energies, the ACD is segmented into 89 tiles of different sizes. The overall ACD efficiency for detection of singly charged relativistic particles entering the tracking detector from the top or sides of the LAT exceeds the required 0.9997.

Charge reconstruction in large-area photomultipliers

Science.gov (United States)

Grassi, M.; Montuschi, M.; Baldoncini, M.; Mantovani, F.; Ricci, B.; Andronico, G.; Antonelli, V.; Bellato, M.; Bernieri, E.; Brigatti, A.; Brugnera, R.; Budano, A.; Buscemi, M.; Bussino, S.; Caruso, R.; Chiesa, D.; Corti, D.; Dal Corso, F.; Ding, X. F.; Dusini, S.; Fabbri, A.; Fiorentini, G.; Ford, R.; Formozov, A.; Galet, G.; Garfagnini, A.; Giammarchi, M.; Giaz, A.; Insolia, A.; Isocrate, R.; Lippi, I.; Longhitano, F.; Lo Presti, D.; Lombardi, P.; Marini, F.; Mari, S. M.; Martellini, C.; Meroni, E.; Mezzetto, M.; Miramonti, L.; Monforte, S.; Nastasi, M.; Ortica, F.; Paoloni, A.; Parmeggiano, S.; Pedretti, D.; Pelliccia, N.; Pompilio, R.; Previtali, E.; Ranucci, G.; Re, A. C.; Romani, A.; Saggese, P.; Salamanna, G.; Sawy, F. H.; Settanta, G.; Sisti, M.; Sirignano, C.; Spinetti, M.; Stanco, L.; Strati, V.; Verde, G.; Votano, L.

2018-02-01

Large-area PhotoMultiplier Tubes (PMT) allow to efficiently instrument Liquid Scintillator (LS) neutrino detectors, where large target masses are pivotal to compensate for neutrinos' extremely elusive nature. Depending on the detector light yield, several scintillation photons stemming from the same neutrino interaction are likely to hit a single PMT in a few tens/hundreds of nanoseconds, resulting in several photoelectrons (PEs) to pile-up at the PMT anode. In such scenario, the signal generated by each PE is entangled to the others, and an accurate PMT charge reconstruction becomes challenging. This manuscript describes an experimental method able to address the PMT charge reconstruction in the case of large PE pile-up, providing an unbiased charge estimator at the permille level up to 15 detected PEs. The method is based on a signal filtering technique (Wiener filter) which suppresses the noise due to both PMT and readout electronics, and on a Fourier-based deconvolution able to minimize the influence of signal distortions—such as an overshoot. The analysis of simulated PMT waveforms shows that the slope of a linear regression modeling the relation between reconstructed and true charge values improves from 0.769 ± 0.001 (without deconvolution) to 0.989 ± 0.001 (with deconvolution), where unitary slope implies perfect reconstruction. A C++ implementation of the charge reconstruction algorithm is available online at [1].

Some of physiological and biochemical responses of Prunus amygdalus to air pollution of the Shazand industrial area

Directory of Open Access Journals (Sweden)

Mehri Askari Mehrabadi

2016-06-01

Full Text Available In today's world where human life is dependent on the industry, the problems impose in the human life along with theachievement of growing in the field of industrial works. One of the challenging problems is entry of pollutants into air that has the destructive effects on human life and environment especially plants. Plants show different responses against the air pollutants. Plant responses can be vary due to climate, geography and plant species. In this study, the effects of air pollutants in the Shazand industrial area (refinery, petrochemical and thermal power stationin Markazi province has been checked on almond. For this purpose, the leaves of almond in Haftadgholle (control area, Shazand (closest city to industrial zone and Kazaz (adjacent industrial zone were collected. Also, soil samples were collected from three areas to determine lead and zinc amounts in soil. Results showed that proline, sulfur, heavy metals (lead and zinc and lipid peroxidation enhanced significantly in Kazaz and Shazand in compared with Haftadgholle, while antioxidant activity of catalase, superoxide dismutase and guaicol peroxidase didn’t significant changes in three areas. The increase of sulfur amount in leaves, lead and zinc in soil of the Kazaz and Shazand regions could be one of the reasons to prove the presence of pollutants in these areas. The increase of lipid peroxidation indicative plant damage against the air pollution. The plant defense mechanism against of stress is the increase of non-enzymatic antioxidant proline. No change in chlorophylls and protein contents reflects increased resistance to the stress.

Water requirements of selected industries

Science.gov (United States)

,; Mussey, Orville D.; Conklin, Howard L.; Durfor, Charles N.; Otts, Louis Ethelbert; Walling, Faulkner B.

1955-01-01

The early industries in America generally were established when and where demands for the products of industry arose. Most of the early industries were so located that their increasing requirements for transportation, raw materials, market, labor, and water supply could be satisfied economically. Many of these original plant locations have continued as modern industrial centers and their output has increased manyfold in meeting the demands of our growing Nation. The recent and current industrial expansion and the trend toward the growth of chemical industries, many Of which are heavy users of water, has resulted in a tremendous increase in the total withdrawal of water for industrial use as well as a large increase in the per capita use of water. This increase in industrial water requirement has strained the capacity of the developed water supplies in many areas, and in some instances the adequacy of the potential water supplies is questionable. The Geological Survey is engaged in preparing and publishing a series of reports describing the developed and undeveloped water resources of many important industrial areas. This work was started initially at the request of the National Securities Resources Board as a means to insure that water supplies are adequate for our rapidly expanding industrial development. Although many factors contribute to establishing the feasibility or even the limits of future industrial development, the one relating to available water supply is extremely important. A knowledge of the water requirements of various industries is valuable therefore in planning the logical development in any area where water supply is a critical factor. Thus far very little suitable information on the water requirements of our major industries is available for general planning. An inventory of unit water-use values in industry therefore would be generally helpful and also might tend to stimulate water-conservation methods. To obtain such information

Quantum efficiency measurement system for large area CsI photodetectors

CERN Document Server

Cusanno, F; Colilli, S; Crateri, R; Fratoni, R; Frullani, S; Garibaldi, F; Giuliani, F; Gricia, M; Lucentini, M; Mostarda, A; Santavenere, F; Veneroni, P; Breuer, H; Iodice, M; Urciuoli, G M; De Cataldo, G; De Leo, R; Lagamba, L; Braem, André

2003-01-01

A proximity focusing freon/CsI RICH detector has been built for kaon physics at Thomas Jefferson National Accelerator Facility (TJNAF or Jefferson Lab), Hall A. The Cherenkov photons are detected by a UV photosensitive CsI film which has been obtained by vacuum evaporation. A dedicated evaporation facility for large area photocathodes has been built for this task. A measuring system has been built to allow the evaluation of the absolute quantum efficiency (QE) just after the evaporation. The evaporation facility is described here, as well as the quantum efficiency measurement device. Results of the QE on-line measurements, for the first time on large area photocathodes, are reported.

Planning of Low-rise Urban Housing Areas

DEFF Research Database (Denmark)

Svensson, O.

In many countries industrialization of house building has led to the building of large, monotonous housing areas with high-rise construction. In Denmark, however, smaller, varied housing areas with low-rise construction and urban features have become predominant. This report contains guidelines...... for the planning of such housing areas....

Large area substrate for surface enhanced Raman spectroscopy (SERS) using glass-drawing technique

Science.gov (United States)

Ivanov, Ilia N; Simpson, John T

2012-06-26

A method of making a large area substrate comprises drawing a plurality of tubes to form a plurality of drawn tubes, and cutting the plurality of drawn tubes into cut drawn tubes. Each cut drawn tube has a first end and a second end along the longitudinal direction of the respective cut drawn tube. The cut drawn tubes collectively have a predetermined periodicity. The method of making a large area substrate also comprises forming a metal layer on the first ends of the cut drawn tubes to provide a large area substrate.

Characterization and Calibration of Large Area Resistive Strip Micromegas Detectors

CERN Document Server

Losel, Philipp Jonathan; The ATLAS collaboration

2015-01-01

Resisitve strip Micromegas detectors behave discharge tolerant. They have been tested extensively as smaller detectors of about 10 x 10 cm$^2$ in size and they work reliably at high rates of 100\\,kHz/cm$^2$ and above. Tracking resolutions well below 100\\,$\\mu$m have been observed for 100 GeV muons and pions. Micromegas detectors are meanwhile proposed as large area muon precision trackers of 2-3\\,m$^2$ in size. To investigate possible differences between small and large detectors, a 1\\,m$^2$ detector with 2048 resistive strips at a pitch of 450 $\\mu$m was studied in the LMU Cosmic Ray Facility (CRF) using two 4 $\\times$ 2.2 m$^2$ large Monitored Drift Tube (MDT) chambers for cosmic muon reference tracking. Segmentation of the resistive strip anode plane in 57.6\\,mm x 95\\,mm large areas has been realized by the readout of 128 strips with one APV25 chip each and by 11 95\\,mm broad trigger scintillators placed along the readout strips.\\\\ This allows for mapping of homogenity in pulse height and efficiency, deter...

Large-area perovskite nanowire arrays fabricated by large-scale roll-to-roll micro-gravure printing and doctor blading

Science.gov (United States)

Hu, Qiao; Wu, Han; Sun, Jia; Yan, Donghang; Gao, Yongli; Yang, Junliang

2016-02-01

Organic-inorganic hybrid halide perovskite nanowires (PNWs) show great potential applications in electronic and optoelectronic devices such as solar cells, field-effect transistors and photodetectors. It is very meaningful to fabricate ordered, large-area PNW arrays and greatly accelerate their applications and commercialization in electronic and optoelectronic devices. Herein, highly oriented and ultra-long methylammonium lead iodide (CH3NH3PbI3) PNW array thin films were fabricated by large-scale roll-to-roll (R2R) micro-gravure printing and doctor blading in ambient environments (humility ~45%, temperature ~28 °C), which produced PNW lengths as long as 15 mm. Furthermore, photodetectors based on these PNWs were successfully fabricated on both silicon oxide (SiO2) and flexible polyethylene terephthalate (PET) substrates and showed moderate performance. This study provides low-cost, large-scale techniques to fabricate large-area PNW arrays with great potential applications in flexible electronic and optoelectronic devices.Organic-inorganic hybrid halide perovskite nanowires (PNWs) show great potential applications in electronic and optoelectronic devices such as solar cells, field-effect transistors and photodetectors. It is very meaningful to fabricate ordered, large-area PNW arrays and greatly accelerate their applications and commercialization in electronic and optoelectronic devices. Herein, highly oriented and ultra-long methylammonium lead iodide (CH3NH3PbI3) PNW array thin films were fabricated by large-scale roll-to-roll (R2R) micro-gravure printing and doctor blading in ambient environments (humility ~45%, temperature ~28 °C), which produced PNW lengths as long as 15 mm. Furthermore, photodetectors based on these PNWs were successfully fabricated on both silicon oxide (SiO2) and flexible polyethylene terephthalate (PET) substrates and showed moderate performance. This study provides low-cost, large-scale techniques to fabricate large-area PNW arrays

Workshop Report on Additive Manufacturing for Large-Scale Metal Components - Development and Deployment of Metal Big-Area-Additive-Manufacturing (Large-Scale Metals AM) System

Energy Technology Data Exchange (ETDEWEB)

Babu, Sudarsanam Suresh [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility; Love, Lonnie J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility; Peter, William H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility; Dehoff, Ryan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Manufacturing Demonstration Facility

2016-05-01

Additive manufacturing (AM) is considered an emerging technology that is expected to transform the way industry can make low-volume, high value complex structures. This disruptive technology promises to replace legacy manufacturing methods for the fabrication of existing components in addition to bringing new innovation for new components with increased functional and mechanical properties. This report outlines the outcome of a workshop on large-scale metal additive manufacturing held at Oak Ridge National Laboratory (ORNL) on March 11, 2016. The charter for the workshop was outlined by the Department of Energy (DOE) Advanced Manufacturing Office program manager. The status and impact of the Big Area Additive Manufacturing (BAAM) for polymer matrix composites was presented as the background motivation for the workshop. Following, the extension of underlying technology to low-cost metals was proposed with the following goals: (i) High deposition rates (approaching 100 lbs/h); (ii) Low cost (<$10/lbs) for steel, iron, aluminum, nickel, as well as, higher cost titanium, (iii) large components (major axis greater than 6 ft) and (iv) compliance of property requirements. The above concept was discussed in depth by representatives from different industrial sectors including welding, metal fabrication machinery, energy, construction, aerospace and heavy manufacturing. In addition, DOE’s newly launched High Performance Computing for Manufacturing (HPC4MFG) program was reviewed. This program will apply thermo-mechanical models to elucidate deeper understanding of the interactions between design, process, and materials during additive manufacturing. Following these presentations, all the attendees took part in a brainstorming session where everyone identified the top 10 challenges in large-scale metal AM from their own perspective. The feedback was analyzed and grouped in different categories including, (i) CAD to PART software, (ii) selection of energy source, (iii

Ecological Study on Hospitalizations for Cancer, Cardiovascular, and Respiratory Diseases in the Industrial Area of Etang-de-Berre in the South of France

Directory of Open Access Journals (Sweden)

Laurence Pascal

2013-01-01

Full Text Available The Etang-de-Berre area is a large industrialized area in the South of France, exposing 300,000 inhabitants to the plumes of its industries. The possible associated health risks are of the highest concern to the population, who asked for studies investigating their health status. A geographical ecological study based on standardized hospitalizations ratios for cancer, cardiovascular, and respiratory diseases was carried out over the 2004–2007 period. Exposure to air pollution was assessed using dispersion models coupled with a geographic information system to estimate an annual mean concentration of sulfur dioxide (SO2 for each district. Results showed an excess risk of hospitalization for myocardial infarction in women living in districts with medium or high SO2 exposure, respectively, 38% [CI 95% 4 : 83] and 54% [14 : 110] greater than women living in districts at the reference level exposure. A 26% [2 : 57] excess risk of hospitalization for myocardial infarction was also observed in men living in districts with high SO2 levels. No excess risk of hospitalization for respiratory diseases or for cancer was observed, except for acute leukemia in men only. Results illustrate the impact of industrial air pollution on the cardiovascular system and call for an improvement of the air quality in the area.

Analysis of the special consequences of the Barij essence industrial complex of Kashan in the development of neighboring rural areas

Directory of Open Access Journals (Sweden)

Mohsen Shaterian

2017-04-01

Full Text Available In the late decades, the development of industrial activities in the rural areas of Iran have caused some changes in different aspects of these areas which influence the special patterns of rural areas. This article aims to identify the changes that have been the results of industrial development and it’s reflection in the development of rural residential areas. The main intention of this study is to analyze the special consequences (economic, social and anatomical of the industrial center of Kashan in the development of neighboring rural areas. The industrial center consists of three factories that are for making essence, making equipment for gardeners and distillers and the Barij Company. All of the above companies are called the Industrial Center of Barij Essence. It has employed 1050 workers from amongst whom 120 people were identified and the questionnaires were randomly distributed among these workers. To analyze the data based on the measurement variables, descriptive and analytic methods (T were used. The results showed that economically, having rural industries has led to an increase in the people’s intake of  calories, seeing more consumption in long lasting goods and more satisfaction in the native people of the area. In addition, there is more social involvement,  improvements in not wasting the residents’ free time, decreasing of  natives immigration out of the rural areas and finally anatomically, quantity and quality improvement in the rural houses.

Industrial metrology as applied to large physics experiments

International Nuclear Information System (INIS)

Veal, D.

1993-05-01

A physics experiment is a large complex 3-D object (typ. 1200 m 3 , 35000 tonnes), with sub-millimetric alignment requirements. Two generic survey alignment tasks can be identified; first, an iterative positioning of the apparatus subsystems in space and, second, a quantification of as-built parameters. The most convenient measurement technique is industrial triangulation but the complexity of the measured object and measurement environment constraints frequently requires a more sophisticated approach. To enlarge the ''survey alignment toolbox'' measurement techniques commonly associated with other disciplines such as geodesy, applied geodesy for accelerator alignment, and mechanical engineering are also used. Disparate observables require a heavy reliance on least squares programs for campaign pre-analysis and calculation. This paper will offer an introduction to the alignment of physics experiments and will identify trends for the next generation of SSC experiments

Industrial metrology as applied to large physics experiments

Energy Technology Data Exchange (ETDEWEB)

Veal, D.

1993-05-01

A physics experiment is a large complex 3-D object (typ. 1200 m{sup 3}, 35000 tonnes), with sub-millimetric alignment requirements. Two generic survey alignment tasks can be identified; first, an iterative positioning of the apparatus subsystems in space and, second, a quantification of as-built parameters. The most convenient measurement technique is industrial triangulation but the complexity of the measured object and measurement environment constraints frequently requires a more sophisticated approach. To enlarge the ``survey alignment toolbox`` measurement techniques commonly associated with other disciplines such as geodesy, applied geodesy for accelerator alignment, and mechanical engineering are also used. Disparate observables require a heavy reliance on least squares programs for campaign pre-analysis and calculation. This paper will offer an introduction to the alignment of physics experiments and will identify trends for the next generation of SSC experiments.

Comparative study of the growth and carbon sequestration potential of Bermuda grass in industrial and urban areas

Directory of Open Access Journals (Sweden)

Usman Ali

2018-06-01

Full Text Available Climate change is a global phenomenon occurring throughout the world. Greenhouse gases (GHGs especially carbon dioxide (CO2 considered to be the major culprit to bring these changes. So, carbon (C sequestration by any mean could be useful to reduce the CO2 level in atmosphere. Turf grasses have the ability to sequester C and minimize the effects of GHGs on the environment. In order to study that how turf grasses can help in C sequestration, Bermuda grass (Cynodon dactylon was grown both at industrial and urban location and its effect on C storage were assessed by soil and plant analysis. Dry deposition of ammonium and nitrate was maximum at both locations through the year. However wet deposition was highest during the months of high rainfall. It was examined through soil analysis that soil organic matter, soil C and nitrogen in both locations increased after second mowing of grass. However, soil pH 6.68 in urban and 7.00 in industrial area and EC 1.86 dS/m in urban and 1.90 dS/m in industrial area decreased as the grass growth continue. Soil fresh weight (27.6 g in urban and (27.28 g industrial area also decreased after first and second mowing of grass. The C levels in plant dry biomass also increased which showed improved ability of plant to uptake C from the soil and store it. Similarly, chlorophyll contents were more in industrial area compared to urban area indicates the positive impact of high C concentration. Whereas stomatal conductance was reduced in high C environment to slow down respiration process. Hence, from present study it can be concluded that the Bermuda grass could be grown in areas with high C concentration in atmosphere for sequestrating C in soil.

Pneumatic radiator of transition radiation for large working area arrangements

International Nuclear Information System (INIS)

Shikhlyarov, K.K.; Gavalyan, V.G.

1993-01-01

An unconventional approach to the constructions of large area regular radiator of X-rays transition radiation is proposed based on the use of a pack of hermetically sealed bags, in which elastic helium layers are formed. A prototype of such a radiator of about 1m 2 area was made for test of the proposed device. 9 refs

The use of large area silicon sensors for thermal neutron detection

International Nuclear Information System (INIS)

Schulte, R.L.; Swanson, F.; Kesselman, M.

1994-01-01

The use of large area planar silicon detectors coupled with gadolinium foils has been investigated to develop a thermal neutron detector having a large area-efficiency (Aε) product. Noise levels due to high detector capacitance limit the size of silicon detectors that can be utilized. Calculations using the Monte Carlo code, MCNP, have been made to determine the variation of intrinsic detection efficiency as a function of the discriminator threshold level required to eliminate the detector noise. Measurements of the noise levels for planar silicon detectors of various resistivities (400, 3000 and 5000 Ω cm) have been made and the optimal detector area-efficiency products have been determined. The response of a Si-Gd-Si sandwich detector with areas between 1 cm 2 and 10.5 cm 2 is presented and the effects of the detector capacitance and reverse current are discussed. ((orig.))

Giga-Investments: Modelling the Valuation of Very Large Industrial Real Investments

OpenAIRE

Collan, Mikael

2004-01-01

In this doctoral dissertation characteristics of very large industrial real investments (VLIRI) are investigated and a special group of VLIRI is defined as giga-investments. The investment decision-making regarding to giga-investments is discussed from the points of view of discounted cash-flow based methods and real option valuation. Based on the bacground of establishing giga-investments, state-of-the-art in capital budgeting (including real options) and by applying fuzzy numbers a novel me...

Beam test of a large area silicon drift detector

International Nuclear Information System (INIS)

Castoldi, A.; Chinnici, S.; Gatti, E.; Longoni, A.; Palma, F.; Sampietro, M.; Rehak, P.; Ballocchi, G.; Kemmer, J.; Holl, P.; Cox, P.T.; Giacomelli, P.; Vacchi, A.

1992-01-01

The results from the tests of the first large area (4 x 4 cm 2 ) planar silicon drift detector prototype in a pion beam are reported. The measured position resolution in the drift direction is (σ=40 ± 10)μm

Life Cycle Assessment of waste management systems in Italian industrial areas: Case study of 1st Macrolotto of Prato

International Nuclear Information System (INIS)

Tarantini, Mario; Loprieno, Arianna Dominici; Cucchi, Eleonora; Frenquellucci, Ferdinando

2009-01-01

Life Cycle Assessment (LCA) is not widely used as a decision-supporting tool in Italy, despite recent European Commission policies fostering its adoption to achieve an energy- and resource-efficient economy. In this paper, an LCA of waste management system of the 1st Macrolotto industrial area is presented. The aims of the study were to identify the environmental critical points of the system and to evaluate opportunities and problems in applying this methodology at industrial area level. After a description of the waste management system of the 1st Macrolotto industrial area, the main assumptions of the study and some elements of the system modelling are presented. Results confirmed that door-to-door separated collection and packaging recycling are successful strategies for reducing the use of natural resources. The cooperation of the waste management company, which was part of the area management structure, was strategic for the completion of the analysis. Country-specific databases and models should be developed for a widespread application of the LCA methodology to waste management in Italian industrial areas.

Levels and isomer profiles of Dechlorane Plus in the surface soils from e-waste recycling areas and industrial areas in South China

Energy Technology Data Exchange (ETDEWEB)

Yu Zhiqiang [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Lu Shaoyou; Gao Shutao; Wang Jingzhi [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100039 (China); Li Huiru, E-mail: huiruli@gig.ac.c [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Zeng Xiangying; Sheng Guoying; Fu Jiamo [State Key Laboratory of Organic Geochemistry, Guangdong Key Laboratory of Environment and Resources, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China)

2010-09-15

Dechlorane Plus (DP) is a highly chlorinated flame retardant. Levels of DP were measured in surface soils from e-waste recycling areas and industrial areas in South China. Higher DP levels were found in e-waste recycling areas (undetectable-47.4 ng/g) than those in industrial areas (0.0336-4.65 ng/g) in South China. The highest DP concentration (3327 ng/g) was found at the e-waste recycling site in Qingyuan, while DP levels fell dramatically with increasing distance away from the recycling site, suggesting that the e-waste recycling activities are an important source of DP emissions. The mean ratios of anti-DP to total DP (f{sub anti}) for different sampling areas ranged from 0.58 to 0.76 and showed no significant difference from the ratio for the technical DP products (t-test, p > 0.05). Further intensive studies are needed to investigate the process of DP degradation and its degradation products. - High DP concentrations were found in the soils from e-waste recycling regions, and e-waste recycling was the major source of DP emissions in South China.

Large area avalanche MRS-photodiodes for nuclear spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Ermalitski, F A; Zalesski, V B

1996-12-31

Problems of application of avalanche photodiodes (APD) in readout systems of nuclear spectrometers are considered. APD`s with a large sensitive area of a diameter 1-5 mm and a high multiplication coefficient 200-1000 are created. MPS-photodiodes provide for the energy resolution 80% at temperature 231 K for detecting gamma-quanta with energy 662 keV. 4 refs.

Industrial Technology for Unprecented Energy and Luminosity The Large Hadron Collider

CERN Document Server

Lebrun, P

2004-01-01

With over 3 billion Swiss francs procurement contracts under execution in industry and the installation of major technical systems in its first 3.3 km sector, the Large Hadron Collider (LHC) construction is now in full swing at CERN, the European Organization for Nuclear Research. The LHC is not only the most challenging particle accelerator, it is also the largest global project ever for a scientific instrument based on advanced technology. Starting from accelerator performance requirements, we recall how these can be met by an appropriate combination of technologies, such as high-field superconducting magnets, superfluid helium cryogenics, power electronics, with particular emphasis on developments required to meet demanding specifications, and industrialization issues which had to be solved for achieving series production of precision components under tight quality assurance and within limited resources. This provides the opportunity for reviewing the production status of the main systems and the progress ...

Molecular beam epitaxy of large-area SnSe2 with monolayer thickness fluctuation

Science.gov (United States)

Park, Young Woon; Jerng, Sahng-Kyoon; Jeon, Jae Ho; Roy, Sanjib Baran; Akbar, Kamran; Kim, Jeong; Sim, Yumin; Seong, Maeng-Je; Kim, Jung Hwa; Lee, Zonghoon; Kim, Minju; Yi, Yeonjin; Kim, Jinwoo; Noh, Do Young; Chun, Seung-Hyun

2017-03-01

The interest in layered materials is largely based on the expectation that they will be beneficial for a variety of applications, from low-power-consuming, wearable electronics to energy harvesting. However, the properties of layered materials are highly dependent on thickness, and the difficulty of controlling thickness over a large area has been a bottleneck for commercial applications. Here, we report layer-by-layer growth of SnSe2, a layered semiconducting material, via van der Waals epitaxy. The films were fabricated on insulating mica substrates with substrate temperatures in the range of 210 °C-370 °C. The surface consists of a mixture of N and (N ± 1) layers, showing that the thickness of the film can be defined with monolayer accuracy (±0.6 nm). High-resolution transmission electron microscopy reveals a polycrystalline film with a grain size of ˜100 nm and clear Moiré patterns from overlapped grains with similar thickness. We also report field effect mobility values of 3.7 cm2 V-1 s-1 and 6.7 cm2 V-1 s-1 for 11 and 22 nm thick SnSe2, respectively. SnSe2 films with customizable thickness can provide valuable platforms for industry and academic researchers to fully exploit the potential of layered materials.

Giat Industries selected for construction of the "Very Large Telescope"

Science.gov (United States)

1995-06-01

Versailles-Satory (France) May 31, 1995 - Giat Industries has just obtained a contract from the European Southern Observatory (ESO) for the construction of the primary and tertiary mirror supports and the positioning apparatus of the world's largest optical telescope. This contract, worth almost 140 million francs, represents over 100,000 hours of work. It was won by Gitech, a division of Giat Industries, in collaboration with the Sfim group, following an international competition between the largest European groups in the space field. Gitech is charged with the development of civil and military industrial equipment for the Giat Industries group, in particular in high technology fields. The VLT (Very Large Telescope) will be installed in Chile before the year 2000; the delivery schedule provides for reception of the first assembly in May 1997. It will consist of four telescopes of 8.2m diameter, providing, in its most powerful configuration, a close-up view of an object measuring one meter on the surface of the moon. The cell, built by Gitech, is one of the key parts of the telescope. It mainly consists of a very rigid metal structure and an electro-hydraulic system of more that 200 hydraulic jacks and 150 electrically-controlled jacks linking the metallic structure to the mirror. This structure, produced to an original design of laser-welded steel chambers, weighs less than 10 tonnes and will support over 37 tonnes of mirror and equipment, while guaranteeing precise positioning to within a micron. The electro-hydraulic jack system, manufactured in collaboration with the Sfim group, will support and position the mirror, and correct its geometry by applying a precise distribution of forces to its rear. The assembly is designed to meet the requirements of para-seismic safety. Gitech is also producing the computerised control system to ensure the operation and the reliability of the assembly.

The use of large area silicon sensors for thermal neutron detection

Energy Technology Data Exchange (ETDEWEB)

Schulte, R.L. (Research and Development Center, Mail Stop: A01-26, Grumman Aerospace Corporation, Bethpage, NY 11714 (United States)); Swanson, F. (Research and Development Center, Mail Stop: A01-26, Grumman Aerospace Corporation, Bethpage, NY 11714 (United States)); Kesselman, M. (Research and Development Center, Mail Stop: A01-26, Grumman Aerospace Corporation, Bethpage, NY 11714 (United States))

1994-12-30

The use of large area planar silicon detectors coupled with gadolinium foils has been investigated to develop a thermal neutron detector having a large area-efficiency (A[epsilon]) product. Noise levels due to high detector capacitance limit the size of silicon detectors that can be utilized. Calculations using the Monte Carlo code, MCNP, have been made to determine the variation of intrinsic detection efficiency as a function of the discriminator threshold level required to eliminate the detector noise. Measurements of the noise levels for planar silicon detectors of various resistivities (400, 3000 and 5000 [Omega] cm) have been made and the optimal detector area-efficiency products have been determined. The response of a Si-Gd-Si sandwich detector with areas between 1 cm[sup 2] and 10.5 cm[sup 2] is presented and the effects of the detector capacitance and reverse current are discussed. ((orig.))

Comparison of DDT and its metabolites concentrations in cow milk from agricultural and industrial areas.

Science.gov (United States)

Kuba, Jarosław; Tomza-Marciniak, Agnieszka; Pilarczyk, Bogumiła; Tarasewicz, Natalia; Pilarczyk, Renata; Ligocki, Marek

2015-01-01

The risk of pesticidal intoxication in humans is severe, especially because of the strongly negative impact on human health. The consequences of the exposure to these substances may include cancerogenesis or endocrine abnormalities resulting for example in decreased fertility. Therefore, the aim of our study was to evaluate the content of dichlorodiphenyltrichloroethane (DDT) and its metabolites in cow milk from two regions of Poland, varying by level of industrialization. Samples were collected from agricultural (n = 25) and industrial (n = 25) areas, and the concentrations of DDT and its metabolites were evaluated by gas chromatography. Residues of DDT were detected in all the milk samples tested, mostly in the samples from the agricultural area, where a total DDT median concentration reached 0.336 μg L(-1). In the milk samples from the industrial area, the median concentration was lower, at 0.131 μg L(-1). 4,4'-DDT was the main metabolite, constituting 83% of total DDT metabolites. Although none of the samples exceeded the level above which they should be considered dangerous, the results showed that the problem of DDT had not diminished and so should be constantly monitored.

Characterization and Calibration of Large Area Resistive Strip Micromegas Detectors

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00389527; The ATLAS collaboration

2016-01-01

Resistive strip Micromegas detectors are discharge tolerant. They have been tested extensively as small detectors of about 10 x 10 cm$^2$ in size and they work reliably at high rates of 100 kHz/cm$^2$ and above. Tracking resolution well below 100 $\\mu$m has been observed for 100 GeV muons and pions. Micromegas detectors are meanwhile proposed as large area muon precision trackers of 2-3 m$^2$ in size. To investigate possible differences between small and large detectors, a 1 m$^2$ detector with 2048 resistive strips at a pitch of 450 $\\mu$m was studied in the LMU Cosmic Ray Measurement Facility (CRMF) using two 4 $\\times$ 2.2 m$^2$ large Monitored Drift Tube (MDT) chambers for cosmic muon reference tracking. A segmentation of the resistive strip anode plane in 57.6 mm x 93 mm large areas has been realized by the readout of 128 strips with one APV25 chip each and by eleven 93 mm broad trigger scintillators placed along the readout strips. This allows for mapping of homogeneity in pulse height and efficiency, d...

Hybrid Ytterbium-doped large-mode-area photonic crystal fiber amplifier for long wavelengths

DEFF Research Database (Denmark)

Petersen, Sidsel Rübner; Alkeskjold, Thomas T.; Poli, Federica

2012-01-01

A large-mode-area Ytterbium-doped photonic crystal fiber amplifier with build-in gain shaping is presented. The fiber cladding consists of a hexagonal lattice of air holes, where three rows are replaced with circular high-index inclusions. Seven missing air holes define the large-mode-area core. ...

Production of the Large-area Plastic Scintillator for Beta-ray Detection using Epoxy Resin

International Nuclear Information System (INIS)

Nam, Jong Soo; Choi, Yong Seok; Hong, Sang Bum; Seo, Bum Kyung; Moon, Jei Kwon; Choi, Jong Won

2016-01-01

In this study, we prepared a plastic scintillator whose manufacturing process is simple and can be freely shaped. A thin plate of the plastic scintillator was manufactured using epoxy resin as a polymer. The plastic scintillator was made by mixing epoxy resin and organic scintillators under various conditions. The optimal mixture ratio to prepare the plastic scintillator was derived from the above results. Using the derived results, we made the large-area plastic scintillator which can quickly measure the contamination site and evaluated characteristics of the large-area plastic scintillator in the laboratory. A thin plate of a plastic scintillator with a simple preparation process can be freely shaped using epoxy resin and organic scintillators such as PPO and POPOP. PPO emits scintillation of light in the ultraviolet range, and POPOP is a wave shifter for moving the wavelength responsible for the PMT. The mixture ratio of PPO and POPOP was determined using their emission spectra. The optimal weight percentage of PPO and POPOP in an organic scintillator was determined to be 0.2 wt%:0.01 wt%. Based on the above results, the large-area plastic scintillator of the window size of a typical pancake-type αβ surface contamination counter was prepared. We want to evaluate the characteristics of the large-area plastic scintillator. However, there were the difficulties in evaluating characteristics of the large-area plastic scintillator. The cross-sectional area of the large-area plastic scintillator is significantly different to PMT

Production of the Large-area Plastic Scintillator for Beta-ray Detection using Epoxy Resin

Energy Technology Data Exchange (ETDEWEB)

Nam, Jong Soo; Choi, Yong Seok; Hong, Sang Bum; Seo, Bum Kyung; Moon, Jei Kwon; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this study, we prepared a plastic scintillator whose manufacturing process is simple and can be freely shaped. A thin plate of the plastic scintillator was manufactured using epoxy resin as a polymer. The plastic scintillator was made by mixing epoxy resin and organic scintillators under various conditions. The optimal mixture ratio to prepare the plastic scintillator was derived from the above results. Using the derived results, we made the large-area plastic scintillator which can quickly measure the contamination site and evaluated characteristics of the large-area plastic scintillator in the laboratory. A thin plate of a plastic scintillator with a simple preparation process can be freely shaped using epoxy resin and organic scintillators such as PPO and POPOP. PPO emits scintillation of light in the ultraviolet range, and POPOP is a wave shifter for moving the wavelength responsible for the PMT. The mixture ratio of PPO and POPOP was determined using their emission spectra. The optimal weight percentage of PPO and POPOP in an organic scintillator was determined to be 0.2 wt%:0.01 wt%. Based on the above results, the large-area plastic scintillator of the window size of a typical pancake-type αβ surface contamination counter was prepared. We want to evaluate the characteristics of the large-area plastic scintillator. However, there were the difficulties in evaluating characteristics of the large-area plastic scintillator. The cross-sectional area of the large-area plastic scintillator is significantly different to PMT.

Identifying Corridors among Large Protected Areas in the United States.

Directory of Open Access Journals (Sweden)

R Travis Belote

Full Text Available Conservation scientists emphasize the importance of maintaining a connected network of protected areas to prevent ecosystems and populations from becoming isolated, reduce the risk of extinction, and ultimately sustain biodiversity. Keeping protected areas connected in a network is increasingly recognized as a conservation priority in the current era of rapid climate change. Models that identify suitable linkages between core areas have been used to prioritize potentially important corridors for maintaining functional connectivity. Here, we identify the most "natural" (i.e., least human-modified corridors between large protected areas in the contiguous Unites States. We aggregated results from multiple connectivity models to develop a composite map of corridors reflecting agreement of models run under different assumptions about how human modification of land may influence connectivity. To identify which land units are most important for sustaining structural connectivity, we used the composite map of corridors to evaluate connectivity priorities in two ways: (1 among land units outside of our pool of large core protected areas and (2 among units administratively protected as Inventoried Roadless (IRAs or Wilderness Study Areas (WSAs. Corridor values varied substantially among classes of "unprotected" non-core land units, and land units of high connectivity value and priority represent diverse ownerships and existing levels of protections. We provide a ranking of IRAs and WSAs that should be prioritized for additional protection to maintain minimal human modification. Our results provide a coarse-scale assessment of connectivity priorities for maintaining a connected network of protected areas.

Investigations of biofilms in the sewerage system of a highly contaminated industrial and mining area for the localization of heavy metal sources. Final report

International Nuclear Information System (INIS)

Cichos, C.; Singliar, U.

1993-02-01

The high heavy metal loading of the river Freiberger Mulde is largely caused by contaminations arising from the drainage area of the town of Freiberg. The diffuse input from the dewatering surface likely makes an important contribution to this pollution. The elimination of the reasons for the pollutant input into the sewerage and, thus, for the extremely high contamination of the sewage sludges requires a localization of sources and transport ways. For this purpose the method of investigation of biofilms on the sewer surface can be applied as a reliable method. For the industrial and mining area of Freiberg besides the different branches of industry especially the secondary emissions from deposits of old mining and metallurgical plants as well as from the extremely loaded surface of soil play an important role. The investigation of sewerage biofilms in the area considered have shown that the input of nickel and tin into the sewer is mainly caused by industry. Sources of zinc and copper above all are domestic wastewaters, whereas lead is originated from the surface run-off. Especially high pollutions of arsen and cadmium were found obviously arising from mining and production scraps. The results obtained should be the basis of activities for definite interruption of the pollutant input into the sewer system. They are a contribution to the restoration of the hydrographical network of Mulde/Elbe. (orig.) [de

Large area imaging of forensic evidence with MA-XRF

NARCIS (Netherlands)

Langstraat, K.; Knijnenberg, A.; Edelman, G.; van de Merwe, L.; van Loon, A.; Dik, J.; van Asten, A.

2017-01-01

This study introduces the use of macroscopic X-ray fluorescence (MA-XRF) for the detection, classification and imaging of forensic traces over large object areas such as entire pieces of clothing and wall paneling. MA-XRF was sufficiently sensitive and selective to detect human biological traces

Large area imaging of forensic evidence with MA-XRF

NARCIS (Netherlands)

Langstraat, Kirsten; Knijnenberg, Alwin; Edelman, Gerda; Van De Merwe, Linda; van Loon, A.; Dik, J.; van Asten, Arian C.

2017-01-01

This study introduces the use of macroscopic X-ray fluorescence (MA-XRF) for the detection, classification and imaging of forensic traces over large object areas such as entire pieces of clothing and wall paneling. MA-XRF was sufficiently sensitive and selective to detect human biological traces

Large eddy simulations of isothermal confined swirling flow in an industrial gas-turbine

International Nuclear Information System (INIS)

Bulat, G.; Jones, W.P.; Navarro-Martinez, S.

2015-01-01

Highlights: • We conduct a large eddy simulation of an industrial gas turbine. • The results are compared with measurements obtained under isothermal conditions. • The method reproduces the observed precessing vortex and central vortex cores. • The profiles of mean and rms velocities are found to be captured to a good accuracy. - Abstract: The paper describes the results of a computational study of the strongly swirling isothermal flow in the combustion chamber of an industrial gas turbine. The flow field characteristics are computed using large eddy simulation in conjunction with a dynamic version of the Smagorinsky model for the sub-grid-scale stresses. Grid refinement studies demonstrate that the results are essentially grid independent. The LES results are compared with an extensive set of measurements and the agreement with these is overall good. The method is shown to be capable of reproducing the observed precessing vortex and central vortex cores and the profiles of mean and rms velocities are found to be captured to a good accuracy. The overall flow structure is shown to be virtually independent of Reynolds number

Supernova Remnants with Fermi Large Area Telescope

Directory of Open Access Journals (Sweden)

Caragiulo M.

2017-01-01

Full Text Available The Large Area Telescope (LAT, on-board the Fermi satellite, proved to be, after 8 years of data taking, an excellent instrument to detect and observe Supernova Remnants (SNRs in a range of energies running from few hundred MeV up to few hundred GeV. It provides essential information on physical processes that occur at the source, involving both accelerated leptons and hadrons, in order to understand the mechanisms responsible for the primary Cosmic Ray (CR acceleration. We show the latest results in the observation of Galactic SNRs by Fermi-LAT.

Providing Public Space Continuities in Post-Industrial Areas through Remodelling Land/Water Connections

Science.gov (United States)

Burda, Izabela M.; Nyka, Lucyna

2017-10-01

This article examines the problem of urban transformation strategies applied in recent years which are based on the creation of new water areas and modification of existing ones. The research is an attempt to prove that modifications of plans of water areas and forms of their borders may play an important role in achieving the best quality public spaces in post-industrial territories. The basis for demonstrating the importance of modifying water borders, and introducing new forms of water-based structures in cities, are theoretical surveys, comparative studies and in-field analyses. It can be seen that post-industrial areas, which used to create voids in the urban fabric, can be perceived as unique but isolated places that should be integrated into the layout of cities. Thus, creating continuity of public spaces that will relate converted areas to their surroundings is a well-known objective of many transformation strategies. This research proves that an effective strategy toward achieving this goal can be based on the modification of relationships between land and water. Namely, the introduction of new water areas, designing new pieces of land that protrude into the water, softening the boundaries of water lines or the opposite, like structuring smaller water flows into well-defined canals, may significantly contribute to the quality of public spaces. As such, all of this fosters the development of sustainable cities and contributes significantly to the emergence of high-quality urban landscapes.

Dwell time considerations for large area cold plasma decontamination

Science.gov (United States)

Konesky, Gregory

2009-05-01

Atmospheric discharge cold plasmas have been shown to be effective in the reduction of pathogenic bacteria and spores and in the decontamination of simulated chemical warfare agents, without the generation of toxic or harmful by-products. Cold plasmas may also be useful in assisting cleanup of radiological "dirty bombs." For practical applications in realistic scenarios, the plasma applicator must have both a large area of coverage, and a reasonably short dwell time. However, the literature contains a wide range of reported dwell times, from a few seconds to several minutes, needed to achieve a given level of reduction. This is largely due to different experimental conditions, and especially, different methods of generating the decontaminating plasma. We consider these different approaches and attempt to draw equivalencies among them, and use this to develop requirements for a practical, field-deployable plasma decontamination system. A plasma applicator with 12 square inches area and integral high voltage, high frequency generator is described.

Voltage uniformity study in large-area reactors for RF plasma deposition

Energy Technology Data Exchange (ETDEWEB)

Sansonnens, L.; Pletzer, A.; Magni, D.; Howling, A.A.; Hollenstein, C. [Ecole Polytechnique Federale, Lausanne (Switzerland). Centre de Recherche en Physique des Plasma (CRPP); Schmitt, J.P.M. [Balzers Process Systems, Palaiseau (France)

1996-09-01

Non-uniform voltage distribution across the electrode area results in inhomogeneous thin-film RF plasma deposition in large area reactors. In this work, a two-dimensional analytic model for the calculation of the voltage distribution across the electrode area is presented. The results of this model are in good agreement with measurements performed without plasma at 13.56 MHz and 70 MHz in a large area reactor. The principal voltage inhomogeneities are caused by logarithmic singularities in the vicinity of RF connections and not by standing waves. These singularities are only described by a two-dimensional model and cannot be intuitively predicted by analogy to a one-dimensional case. Plasma light emission measurements and thickness homogeneity studies of a-Si:H films show that the plasma reproduces these voltage inhomogeneities. Improvement of the voltage uniformity is investigated by changing the number and position of the RF connections. (author) 13 figs., 20 refs.

Uniformity studies in large area triple-GEM based detectors

Energy Technology Data Exchange (ETDEWEB)

Akl, M. Abi [Science Program, Texas A& M University at Qatar, PO Box 23874, Doha (Qatar); Bouhali, O., E-mail: othmane.bouhali@qatar.tamu.edu [Science Program, Texas A& M University at Qatar, PO Box 23874, Doha (Qatar); Qatar Computing Research Institute, Hamad Bin Khalifa University, PO Box 5825, Doha (Qatar); Castaneda, A.; Maghrbi, Y.; Mohamed, T. [Science Program, Texas A& M University at Qatar, PO Box 23874, Doha (Qatar)

2016-10-01

Gas Electron Multiplier (GEM) based detectors have been used in many applications since their introduction in 1997. Large areas, e.g. exceeding 30×30 cm{sup 2}, of GEM detectors are foreseen in future experiments which puts stringent requirements on the uniformity of response across the detection area. We investigate the effect of small variations of several parameters that could affect the uniformity. Parameters such as the anode pitch, the gas gap, the size and the shape of the holes are investigated. Simulation results are presented and compared to previous experimental data.

Two-group modeling of interfacial area transport in large diameter channels

Energy Technology Data Exchange (ETDEWEB)

Schlegel, J.P., E-mail: schlegelj@mst.edu [Department of Mining and Nuclear Engineering, Missouri University of Science and Technology, 301 W 14th St., Rolla, MO 65409 (United States); Hibiki, T.; Ishii, M. [School of Nuclear Engineering, Purdue University, 400 Central Dr., West Lafayette, IN 47907 (United States)

2015-11-15

Highlights: • Implemented updated constitutive models and benchmarking method for IATE in large pipes. • New model and method with new data improved the overall IATE prediction for large pipes. • Not all conditions well predicted shows that further development is still required. - Abstract: A comparison of the existing two-group interfacial area transport equation source and sink terms for large diameter channels with recently collected interfacial area concentration measurements (Schlegel et al., 2012, 2014. Int. J. Heat Fluid Flow 47, 42) has indicated that the model does not perform well in predicting interfacial area transport outside of the range of flow conditions used in the original benchmarking effort. In order to reduce the error in the prediction of interfacial area concentration by the interfacial area transport equation, several constitutive relations have been updated including the turbulence model and relative velocity correlation. The transport equation utilizing these updated models has been modified by updating the inter-group transfer and Group 2 coalescence and disintegration kernels using an expanded range of experimental conditions extending to pipe sizes of 0.304 m [12 in.], gas velocities of up to nearly 11 m/s [36.1 ft/s] and liquid velocities of up to 2 m/s [6.56 ft/s], as well as conditions with both bubbly flow and cap-bubbly flow injection (Schlegel et al., 2012, 2014). The modifications to the transport equation have resulted in a decrease in the RMS error for void fraction and interfacial area concentration from 17.32% to 12.3% and 21.26% to 19.6%. The combined RMS error, for both void fraction and interfacial area concentration, is below 15% for most of the experiments used in the comparison, a distinct improvement over the previous version of the model.

Characterization of new hexagonal large area Geiger Avalanche Photodiodes

International Nuclear Information System (INIS)

Boccone, V.; Aguilar, J.A.; Della Volpe, D.; Christov, A.; Montaruli, T.; Rameez, M.; Basili, A.

2013-06-01

Photomultipliers (PMTs) are the standard detector for construction of the current generation of imaging Atmospheric Cherenkov Telescopes (IACTs). Despite impressive improvements in QE and reliability in the last years, these devices suffer from the limitation of being unable to operate in the partially illuminated sky (during full or partial moon periods) as the excess light leads to a significant increase in the rate of ageing of the devices themselves and consequently limit the life of the camera. A viable alternative is the large area Geiger-mode avalanche photodiodes (G-APDs also known as Silicon Photomultipliers or SiPMs) that are commercially available from different producers in various types and dimensions. The sufficiency of the maturity of this technology for application to Cherenkov Astronomy has already been demonstrated by the FACT telescope. One of the camera designs under study for the 4 m Davies Cotton Telescope foresees the utilization of a large area G-APDs coupled to non imaging light concentrators. In collaboration with Hamamatsu and deriving from their current technology, we have designed a new hexagonal shaped large area G-APD HEX S12516 which when coupled to a Winston cone of 24 degrees cutting angle allows for a pixel angular resolution of 0.25 degrees for a f/D 1.4 telescope with a diameter of 4 m. The device, available in 2 different cell size configurations (50 μm and 100 μm), is divided into 4 different channels powered in common cathode mode. A temperature sensor was included for a better temperature evaluation in the characterization phase. The first 3 prototypes were fully characterized and the results are compared to the larger area devices commercially available such as the S10985-050C (2x2 array of 3x3 mm 2 G-APDs). The photo-detection efficiency is measured applying the Poisson statistics method using pulsed LED at 7 different wavelengths from 355 to 670 nm and for different bias over-voltages (V ov ). Optical crosstalk and

Terpuruknya Industri Mebel Rotan Cirebon

Directory of Open Access Journals (Sweden)

Oktavianus Marti Nangoy

2011-04-01

Full Text Available Cirebon area has long been known as an area that has great potential in the field of furniture and handicraft industry with raw materials of rattan. This region really does not have trees but because of the large rattan hereditary craftsmen at work there, and many there menyebabkan Cirebon rattan industry as a major regional craftsmen and the largest cane producer in Indonesia. But that condition did not last long because it feared since the Minister of Trade Decree No.12 of 2005, contains the opening tap on raw rattan exports, leading, manufacturers prefer to export the raw materials of rattan. Prices of raw materials for furniture and rattan craft also be high because the prices charged for local producers to use the benchmark export price. This ministerial decree on the one side benefit exporters but the industry shut down one side. 

FUTURE SCOPE OF WOMEN CARRIER IN THE PRINTING INDUSTRY: THE CHALLENGES OF WOMEN IN PRINTING OGANIZATIONS (A SURVEY OF TWENTY FIVE COMPANIES "SMALL, MEDIUM AND LARGE PRINTING ORGANIZATION" IN AREA "NCR DELHI AND HISAR, HR".)

OpenAIRE

Mr. Azad Singh*

2017-01-01

Women carrier in printing organization today, printing industry is growing with an expositional rate & required skills manpower. In this survey based paper to getting recruit of women 10%small, 30%medium and 60% large scale print industry. Objective of this paper is too filled out manpower skills printing industries are seaking in B.Tech women printing students to bridge the gap between skills and required in printing organization. A survey 25 companies was carried out. the result indicated t...

New Technology-Large-Area Three- Dimensional Surface Profiling Using Only Focused Air-Coupled Ultrasound-Given 1999 R&D 100 Award

Science.gov (United States)

Roth, Don J.; Kautz, Harold E.; Abel, Phillip B.; Whalen, Mike F.; Hendricks, J. Lynne; Bodis, James R.

2000-01-01

Surface topography, which significantly affects the performance of many industrial components, is normally measured with diamond-tip profilometry over small areas or with optical scattering methods over larger areas. To develop air-coupled surface profilometry, the NASA Glenn Research Center at Lewis Field initiated a Space Act Agreement with Sonix, Inc., through two Glenn programs, the Advanced High Temperature Engine Materials Program (HITEMP) and COMMTECH. The work resulted in quantitative surface topography profiles obtained using only high-frequency, focused ultrasonic pulses in air. The method is nondestructive, noninvasive, and noncontact, and it does not require light-reflective surfaces. Air surface profiling may be desirable when diamond-tip or laserbased methods are impractical, such as over large areas, when a significant depth range is required, or for curved surfaces. When the configuration is optimized, the method is reasonably rapid and all the quantitative analysis facilities are online, including two- and three-dimensional visualization, extreme value filtering (for faulty data), and leveling.

THE CONCEPT OF SUSTAINABLE DEVELOPMENT THROUGH ECONOMIC GROWTH AND DIVERSIFICATION OF THE LABOUR MARKET IN THE INDUSTRIAL AREAS AFFECTED BY RESTRUCTURING

Directory of Open Access Journals (Sweden)

Marius Eremia VLAICU POPA

2013-06-01

Full Text Available In the context of what is implemented through dualism "ecosystem-efficient", sustainable development involves the care of the human potential of the present situation and the future of its natural resources, energy, materials and information. As an effect of responsibility for future generations, the efficient use of resources requires, at the same time, the operation of a sustainable economy, by diversification and development of the labour market in order to meet present and future demands of human society. At local and regional level, through the closing of mines and large enterprises, with an effect in restructuring the economic sector and employment, development strategies and rehabilitation of the affected industrial areas as a common principle approach, analyzing the problems, defining the objectives and policies, identifying actions to attack problems and provide for mechanisms that will enable the progress control. In this paper it is presented the concept of sustainable development as imperative for economic growth, diversification and development of the labour market, being dealt the representative criteria and principles of sustainable development strategy of any company. Are defined the components and objectives of a strategy for local and regional development of industrial areas affected by the restructuring.

Job-housing imbalance and commuting of coastal industrial town in Liaoning province, China

Science.gov (United States)

Chen, Fei; Lu, Wei; Cai, Jun; Yang, Qiyao

2017-11-01

During the Twelve Five period, China promulgated industrial policies promote the energy-intensive industries relocate to coastal areas in order to utilize marine shipping resources. Consequently, some major state-owned steel and petrochemical enterprises have relocated and resulted in a large scale coastal area development. Restricted by the port construction, most of the coastal industrial areas are located in the outer suburbs. To balance between employment and housing, new industrial coastal towns were constructed. In this paper, we adopt a case-study approach to analysis some typical industrial coastal towns of Liaoning Province situated in the Bohai Bay, which is currently under rapid economic growth. Our investigations reflect the common phenomenon of long distance commuting and massive amount of vacant residences. More specifically, large plant relocation caused hundreds of kilometers of daily commute and enterprises had to provide housing subsidies and education incentives to motivate employees to relocate to coastal areas. Nonetheless, many employees still refuse to relocate due to job stability, diverse needs of family members and access to convenient services. These employees averaged 4 hours of commute daily and some who lived further had to reside in temporary industrial housing units and subject to long-term family separation. As a result, only a small portion of employees purchase new coastal residences but mostly for investment and retirement purposes, leading to massive vacancy and ghost-town phenomenon. In contrast to the low demand, coastal areas tend to develop large amount of residences prior to industrial relocation, which may be directly related to local government finances. Some local governments have sold residential land to developers to general revenue to support the subsequent industrial development. Subject to the strong preference of ocean- view, residential housing developers tend to select coast-line land to construct new residential

Prospecting direction and favourable target areas for exploration of large and super-large uranium deposits in China

International Nuclear Information System (INIS)

Liu Xingzhong

1993-01-01

A host of large uranium deposits have been successively discovered abroad by means of geological exploration, metallogenetic model studies and the application of new geophysical and geochemical methods since 1970's. Thorough undertaking geological research relevant to prospecting for super large uranium deposits have attracted great attention of the worldwide geological circle. The important task for the vast numbers of uranium geological workers is to make an afford to discover more numerous large and super large uranium deposits in China. The author comprehensively analyses the regional geological setting and geological metallogenetic conditions for the super large uranium deposits in the world. Comparative studies have been undertaken and the prospecting direction and favourable target areas for the exploration of super large uranium deposits in China have been proposed

Wind energy in industrial areas optional, but not obvious. A study on the chances and constraints for the use of wind energy in industrial parks

International Nuclear Information System (INIS)

Schoolderman, J.A.; Verbeet, E.; Jochems, A.; Versteeg, K.

2000-06-01

The feasibility of installing wind turbines in industrial parks in the Netherlands has been investigated. An overview is given of possibilities and constraints to fit in wind turbines in industrial areas, based on the results of a literature study, a market consultation of sectoral organizations, representatives of local industrial circles and industrial experts in the field of renewable energy. Also a telephone survey was carried out among 130 entrepreneurs in the Netherlands to determine their attitudes towards the use of sustainable energy and wind energy in industrial parks. The results of the attitude study are published in a separate report for which a separate abstract has been prepared. The intermediate results were discussed at a meeting (23 February 2000), in which representatives from the industry, provinces, municipalities and the government participated

Large-area burns with pandrug-resistant Pseudomonas aeruginosa infection and respiratory failure.

Science.gov (United States)

Ning, Fang-Gang; Zhao, Xiao-Zhuo; Bian, Jing; Zhang, Guo-An

2011-02-01

Infection due to pandrug-resistant Pseudomonas aeruginosa (PDRPA) has become a challenge in clinical practice. The aim of this research was to summarize the treatment of large-area burns (60% - 80%) with PDRPA infection and respiratory failure in our hospital over the last two years, and to explore a feasible treatment protocol for such patients. We retrospectively analyzed the treatment of five patients with large-area burns accompanied by PDRPA infection and respiratory failure transferred to our hospital from burn units in hospitals in other Chinese cities from January 2008 to February 2010. Before PDRPA infection occurred, all five patients had open wounds with large areas of granulation because of the failure of surgery and dissolving of scar tissue; they had also undergone long-term administration of carbapenems. This therapy included ventilatory support, rigorous repair of wounds, and combined antibiotic therapy targeted at drug-resistance mechanisms, including carbapenems, ciprofloxacin, macrolide antibiotics and β-lactamase inhibitors. Four patients recovered from burns and one died after therapy. First, compromised immunity caused by delayed healing of burn wounds in patients with large-area burns and long-term administration of carbapenems may be the important factors in the initiation and progression of PDRPA infection. Second, if targeted at drug-resistance mechanisms, combined antibiotic therapy using carbapenems, ciprofloxacin, macrolide antibiotics and β-lactamase inhibitors could effectively control PDRPA infection. Third, although patients with large-area burns suffered respiratory failure and had high risks from anesthesia and surgery, only aggressive skin grafting with ventilatory support could control the infection and save lives. Patients may not be able to tolerate a long surgical procedure, so the duration of surgery should be minimized, and the frequency of surgery increased.

Low-Power Large-Area Radiation Detector for Space Science Measurements

Data.gov (United States)

National Aeronautics and Space Administration — The objective of this task is to develop a low-power, large-area detectors from SiC, taking advantage of very low thermal noise characteristics and high radiation...

Distribution to heavy metals in sediments of the Venice Lagoon: The role of the industrial area

International Nuclear Information System (INIS)

Frignani, M.; Bellucci, L.G.; Ravanelli, M.; Paolucci, D.

1999-01-01

The Venice Lagoon has been heavily polluted both from diffuse and direct sources. It has been recently established that the atmospheric delivery of contaminants to the lagoon can be very significant in zones far from direct sources, but the influence of the industrial area of Porto Marghera, though widely recognized, has not been entirely described and quantified. In order to assess the temporal and spatial variability of metal pollution, and to better understand the contribution of the industrial channels as sources of contaminants, in May 1996 we sampled 18 stations in the lagoon and 9 in the channels of the industrial area of Porto Marghera. At each site a short core, 10 cm long, was taken and immediately extruded to obtain 4 slices 2-2.5 cm thick. Sediment samples have been analysed for As, Cd, Pb, and Zn after acid extraction

Large-area imaging micro-well detectors for high-energy astrophysics

CERN Document Server

Deines-Jones, P; Hunter, S D; Jahoda, K; Owens, S M

2002-01-01

Micro-well detectors are pixelized imaging sensors that can be inexpensively fabricated in very large arrays. Owing to their intrinsic gain and operation at room temperature, they can be instrumented at very low power, per unit area, making them valuable for a variety of space-flight applications where wide-angle X-ray imaging or large-area particle tracking is required. For example, micro-well detectors have been chosen as the focal plane imager for Lobster-ISS, a proposed soft X-ray all-sky monitor. We have fabricated detectors which image X-rays with 200 mu m FWHM resolution at 3 keV. In agreement with other groups using similar geometries, we find nominal proportional counter energy resolution (20% at 6 keV in P-10), and stable operation at gas gains up to 30,000.

The potential for ore and industrial minerals in the Forsmark area

Energy Technology Data Exchange (ETDEWEB)

Lindroos, Hardy [MIRAB Mineral Resurser AB, Uppsala (Sweden); Isaksson, Hans; Thunehed, Hans [GeoVista AB, Luleaa (Sweden)

2004-03-01

A survey has been made of existing information concerning the potential for ore and industrial minerals in and near the candidate area for a deep repository in Forsmark. A deep repository for spent nuclear fuel should not be located in a rock type or an area where mineral extraction might be considered in the future, since this would make it impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities. The survey has made use of all the geoscientific information that was compiled in the more regional investigations in Oesthammar Municipality in 1996-97. In cooperation with the Geological Survey of Sweden (SGU), a new, more detailed mineral resources map has been prepared. The map shows areas with an ore potential that may be unsuitable or unfavourable for siting of a deep repository. The results of the recently completed geophysical helicopter surveys of the Forsmark area are presented in a special chapter. The judgement of the area's ore potential is in part based on the geophysical evaluation of these measurements. Furthermore, the survey obtained information from ongoing deep drillings from the site investigation in Forsmark. In order to better be able to judge the ore potential, the survey has initiated a geochemical investigation of activated soil samples, plus an ore geology sampling of a section in the deep borehole KFM02A, where a hydrothermally altered zone was detected in 2003.The first results from these samplings are presented in the report, which also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. Some suggestions are made for further ore geology investigations. The mineral resources map shows that there is an elongate northwest-southeast zone south and southwest of the candidate area which has a potential for skarn iron ore, and possibly for copper and zinc

The potential for ore and industrial minerals in the Forsmark area

International Nuclear Information System (INIS)

Lindroos, Hardy; Isaksson, Hans; Thunehed, Hans

2004-03-01

A survey has been made of existing information concerning the potential for ore and industrial minerals in and near the candidate area for a deep repository in Forsmark. A deep repository for spent nuclear fuel should not be located in a rock type or an area where mineral extraction might be considered in the future, since this would make it impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities. The survey has made use of all the geoscientific information that was compiled in the more regional investigations in Oesthammar Municipality in 1996-97. In cooperation with the Geological Survey of Sweden (SGU), a new, more detailed mineral resources map has been prepared. The map shows areas with an ore potential that may be unsuitable or unfavourable for siting of a deep repository. The results of the recently completed geophysical helicopter surveys of the Forsmark area are presented in a special chapter. The judgement of the area's ore potential is in part based on the geophysical evaluation of these measurements. Furthermore, the survey obtained information from ongoing deep drillings from the site investigation in Forsmark. In order to better be able to judge the ore potential, the survey has initiated a geochemical investigation of activated soil samples, plus an ore geology sampling of a section in the deep borehole KFM02A, where a hydrothermally altered zone was detected in 2003.The first results from these samplings are presented in the report, which also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. Some suggestions are made for further ore geology investigations. The mineral resources map shows that there is an elongate northwest-southeast zone south and southwest of the candidate area which has a potential for skarn iron ore, and possibly for copper and zinc, although

Reactive dual magnetron sputtering for large area application

International Nuclear Information System (INIS)

Struempfel, J.

2002-01-01

Production lines for large area coating demand high productivity of reactive magnetron sputtering processes. Increased dynamic deposition rates for oxides and nitrides were already obtained by using of highly powered magnetrons in combination with advanced sputter techniques. However, besides high deposition rates the uniformity of such coatings has to be carefully considered. First the basics of reactive sputtering processes and dual magnetron sputtering are summarized. Different methods for process stabilization and control are commonly used for reactive sputtering. The Plasma Emission Monitor (PE M) offers the prerequisite for fast acting process control derived from the in-situ intensity measurements of a spectral line of the sputtered target material. Combined by multiple Plasma Emission Monitor control loops segmented gas manifolds are able to provide excellent thin film uniformity at high deposition rates. The Dual Magnetron allows a broad range of processing by different power supply modes. Medium frequency, DC and pulsed DC power supplies can be used for high quality layers. Whereas the large area coating of highly isolating layers like TiO 2 or SiO 2 is dominated by MF sputtering best results for coating with transparent conductive oxides are obtained by dual DC powering of the dual magnetron arrangement. (Author)

Collaborative research between academia and industry using a large clinical trial database: a case study in Alzheimer's disease

DEFF Research Database (Denmark)

Jones, Roy; Wilkinson, David; Lopez, Oscar L

2011-01-01

Large clinical trials databases, developed over the course of a comprehensive clinical trial programme, represent an invaluable resource for clinical researchers. Data mining projects sponsored by industry that use these databases, however, are often not viewed favourably in the academic medical...... community because of concerns that commercial, rather than scientific, goals are the primary purpose of such endeavours. Thus, there are few examples of sustained collaboration between leading academic clinical researchers and industry professionals in a large-scale data mining project. We present here...

Saving Energy in Industrial Companies: Case Studies of Energy Efficiency Programs in Large U.S. Industrial Corporations and the Role of Ratepayer-Funded Support

Energy Technology Data Exchange (ETDEWEB)

None, None

2017-03-08

This paper is designed for companies looking to cut costs through energy savings, ratepayer-funded program administrators interested in increasing large industrial company participation in energy efficiency program offerings, and state utility commissions.

Application of large radiation sources in chemical processing industry

International Nuclear Information System (INIS)

Krishnamurthy, K.

1977-01-01

Large radiation sources and their application in chemical processing industry are described. A reference has also been made to the present developments in this field in India. Radioactive sources, notably 60 Co, are employed in production of wood-plastic and concrete-polymer composites, vulcanised rubbers, polymers, sulfochlorinated paraffin hydrocarbons and in a number of other applications which require deep penetration and high reliability of source. Machine sources of electrons are used in production of heat shrinkable plastics, insulation materials for cables, curing of paints etc. Radiation sources have also been used for sewage hygienisation. As for the scene in India, 60 Co sources, gamma chambers and batch irradiators are manufactured. A list of the on-going R and D projects and organisations engaged in research in this field is given. (M.G.B.)

Large-area photonic crystals

Science.gov (United States)

Ruhl, Tilmann; Spahn, Peter; Hellmann, Gotz P.; Winkler, Holger

2004-09-01

Materials with a periodically modulated refractive index, with periods on the scale of light wavelengths, are currently attracting much attention because of their unique optical properties which are caused by Bragg scattering of the visible light. In nature, 3d structures of this kind are found in the form of opals in which monodisperse silica spheres with submicron diameters form a face-centered-cubic (fcc) lattice. Artificial opals, with the same colloidal-crystalline fcc structure, have meanwhile been prepared by crystallizing spherical colloidal particles via sedimentation or drying of dispersions. In this report, colloidal crystalline films are introduced that were produced by a novel technique based on shear flow in the melts of specially designed submicroscopic silica-polymer core-shell hybrid spheres: when the melt of these spheres flows between the plates of a press, the spheres crystallize along the plates, layer by layer, and the silica cores assume the hexagonal order corresponding to the (111) plane of the fcc lattice. This process is fast and yields large-area films, thin or thick. To enhance the refractive index contrast in these films, the colloidal crystalline structure was inverted by etching out the silica cores with hydrofluoric acid. This type of an inverse opal, in which the fcc lattice is formed by mesopores, is referred to as a polymer-air photonic crystal.

Performance Assessment/Composite Analysis Modeling to Support a Holistic Strategy for the Closure of F Area, a Large Nuclear Complex at the Savannah River Site

International Nuclear Information System (INIS)

COOK, JAMES

2004-01-01

A performance-based approach is being used at the Savannah River Site to close the F area Complex. F Area consists of a number of large industrial facilities including plutonium separations, uranium fuel fabrication, tanks for storing high level waste and a number of smaller operations. A major part of the overall closure strategy is the use of techniques derived from the Performance Assessment and Composite Analysis requirements for low level waste disposal at DOE sites. This process will provide a means of demonstrating the basis for deactivation, decommissioning and closure decisions to management, stakeholders and regulators

A central solar-industrial waste heat heating system with large scale borehole thermal storage

NARCIS (Netherlands)

Guo, F.; Yang, X.; Xu, L.; Torrens, I.; Hensen, J.L.M.

2017-01-01

In this paper, a new research of seasonal thermal storage is introduced. This study aims to maximize the utilization of renewable energy source and industrial waste heat (IWH) for urban district heating systems in both heating and non-heating seasons through the use of large-scale seasonal thermal

Industrial applications at GANIL

International Nuclear Information System (INIS)

Delagrange, H.

1993-01-01

After a first round of industrial applications using heavy ion beams, GANIL has refocused these activities along the lines defined by a strategy and market study. Heavy ion industrial applications take their roots in the physical effects of the interactions occurring between heavy ion projectiles and matter. Specific equipments operated by GANIL or CIRIL allow users to take benefit from these effects. By heavy ion irradiation, industrial companies qualify radiation hardened electronic components and sensitize plastic films to produce 'nuclear track' membranes. Research and development programs with laboratories of the public sector, focus on heavy ion lithography dedicated to large area luminescent flat screens with field emitter microtips and on tribology with radioactive implanted ions. Even sometimes facing difficulties to fill the gap between industry and research, GANIL is eager to promote heavy ion beam technologies. (author) 36 refs., 6 figs., 5 tabs

Large area, surface discharge pumped, vacuum ultraviolet light source

Science.gov (United States)

Sze, R.C.; Quigley, G.P.

1996-12-17

Large area, surface discharge pumped, vacuum ultraviolet (VUV) light source is disclosed. A contamination-free VUV light source having a 225 cm{sup 2} emission area in the 240-340 nm region of the electromagnetic spectrum with an average output power in this band of about 2 J/cm{sup 2} at a wall-plug efficiency of approximately 5% is described. Only ceramics and metal parts are employed in this surface discharge source. Because of the contamination-free, high photon energy and flux, and short pulse characteristics of the source, it is suitable for semiconductor and flat panel display material processing. 3 figs.

[Thinking on development of Shanxi Astragali Radix industry].

Science.gov (United States)

Qin, Xue-Mei; Li, Ai-Ping; Li, Ke; Li, An-Ping; Ning, Lu-Hong

2016-12-01

Shanxi, a traditional production area to produce genuine Astragali Radix of high quality, has experienced major changes in the pattern of resources. This area once accounted for half of Astragali Radix industry, but now only serves as the largest supply area of traditional wild Astragali Radix. Furthermore, the strategic position of Shanxi Astragali Radix industry will become more prominent and more important to economic and social development in face of the diversity of market demands, especially for the strong demands of high-end Astragali Radix. In addition, Astragalus industry involves the simultaneous development of the first, second and tertiary industries in many areas, and it is typical and representative in the traditional Chinese medicine industry development. However, the application and industrial development of Shanxi Astragali Radix have been restricted due to the problems such as blind promotion of transplanting cultivation technology, and lack of science and technology including efficacy investigation, safety evaluation, standardization and controllability studies. Therefore, we would analyze the production history, resource structure, the current situation and progress of industry development, scientific research foundation and existing problem in this paper, and put forward countermeasures for development and technical innovation in order to make Astragali Radix industry bigger and stronger through innovation-driven and make benefits for demos. This thought provides a reference for the exploratory development of other large varieties of Chinese medicinal materials. Copyright© by the Chinese Pharmaceutical Association.

Large area electron beam diode development

International Nuclear Information System (INIS)

Helava, H.; Gilman, C.M.; Stringfield, R.M.; Young, T.

1983-01-01

A large area annular electron beam diode has been tested at Physics International Co. on the multi-terawatt PITHON generator. A twelve element post hole convolute converted the coaxial MITL into a triaxial arrangement of anode current return structures both inside and outside the cathode structure. The presence of both inner and outer current return paths provide magnetic pressure balance for the beam, as determined by diode current measurements. X-ray pinhole photographs indicated uniform emission with intensity maxima between the post positions. Current losses in the post hole region were negligible, as evidenced by the absence of damage to the aluminum hardware. Radial electron flow near the cathode ring however did damage the inner anode cylinder between the post positions. Cutting away these regions prevented further damage of the transmission lines

Edge field emission of large-area single layer graphene

Energy Technology Data Exchange (ETDEWEB)

Kleshch, Victor I., E-mail: klesch@polly.phys.msu.ru [Department of Physics, M.V. Lomonosov Moscow State University, Moscow 119991 (Russian Federation); Bandurin, Denis A. [Department of Physics, M.V. Lomonosov Moscow State University, Moscow 119991 (Russian Federation); Orekhov, Anton S. [Department of Physics, M.V. Lomonosov Moscow State University, Moscow 119991 (Russian Federation); A.V. Shubnikov Institute of Crystallography, RAS, Moscow 119333 (Russian Federation); Purcell, Stephen T. [ILM, Université Claude Bernard Lyon 1 et CNRS, UMR 5586, 69622 Villeurbanne (France); Obraztsov, Alexander N. [Department of Physics, M.V. Lomonosov Moscow State University, Moscow 119991 (Russian Federation); Department of Physics and Mathematics, University of Eastern Finland, Joensuu 80101 (Finland)

2015-12-01

Graphical abstract: - Highlights: • Stable field emission was observed from the edge of large-area graphene on quartz. • A strong hysteresis in current–voltage characteristics was observed. • The hysteresis was explained by mechanical peeling of graphene edge from substrate. • Reversible peeling of graphene edge may be used in microelectromechanical systems. - Abstract: Field electron emission from the edges of large-area (∼1 cm × 1 cm) graphene films deposited onto quartz wafers was studied. The graphene was previously grown by chemical vapour deposition on copper. An extreme enhancement of electrostatic field at the edge of the films with macroscopically large lateral dimensions and with single atom thickness was achieved. This resulted in the creation of a blade type electron emitter, providing stable field emission at low-voltage with linear current density up to 0.5 mA/cm. A strong hysteresis in current–voltage characteristics and a step-like increase of the emission current during voltage ramp up were observed. These effects were explained by the local mechanical peeling of the graphene edge from the quartz substrate by the ponderomotive force during the field emission process. Specific field emission phenomena exhibited in the experimental study are explained by a unique combination of structural, electronic and mechanical properties of graphene. Various potential applications ranging from linear electron beam sources to microelectromechanical systems are discussed.

Degenerate four wave mixing in large mode area hybrid photonic crystal fibers

DEFF Research Database (Denmark)

Petersen, Sidsel Rübner; Alkeskjold, Thomas Tanggaard; Lægsgaard, Jesper

2013-01-01

Spontaneous degenerate four wave mixing (FWM) is investigated in large mode area hybrid photonic crystal fibers, in which photonic bandgap guidance and index guidance is combined. Calculations show the parametric gain is maximum on the edge of a photonic bandgap, for a large range of pump...... wavelengths. The FWM products are observed on the edges of a transmission band experimentally, in good agreement with the numerical results. Thereby the bandedges can be used to control the spectral positions of FWM products through a proper fiber design. The parametric gain control combined with a large mode...... area fiber design potentially allows for power scaling of light at wavelengths not easily accessible with e.g. rare earth ions....

Large area strain analysis using scanning transmission electron microscopy across multiple images

International Nuclear Information System (INIS)

Oni, A. A.; Sang, X.; LeBeau, J. M.; Raju, S. V.; Saxena, S.; Dumpala, S.; Broderick, S.; Rajan, K.; Kumar, A.; Sinnott, S.

2015-01-01

Here, we apply revolving scanning transmission electron microscopy to measure lattice strain across a sample using a single reference area. To do so, we remove image distortion introduced by sample drift, which usually restricts strain analysis to a single image. Overcoming this challenge, we show that it is possible to use strain reference areas elsewhere in the sample, thereby enabling reliable strain mapping across large areas. As a prototypical example, we determine the strain present within the microstructure of a Ni-based superalloy directly from atom column positions as well as geometric phase analysis. While maintaining atomic resolution, we quantify strain within nanoscale regions and demonstrate that large, unit-cell level strain fluctuations are present within the intermetallic phase

Peat wetland as a natural filter of effluents from adjacent industrial areas

Directory of Open Access Journals (Sweden)

József DEZSO

2015-12-01

Full Text Available The main objective of the project is the study of a peat wetland functioning as recipient of effluents from former and present-day industrial activities. The investigation was focused on heavy metal contaminations and their probable mobilization or fixation. The studied peatbog is a typical Eastern European wetland, located in Hungary on the border between medium mountains (Bakony Mountains and a Neogene basin (the Sárrét, an area under nature conservation. Watercourses and prevailing air currents can transport contaminants from industrial areas to the wetland. At first the basic parameters of surface waters and subsurface conditions (soils, groundwater were investigated. These parameters (EC, Cl are possible indicators of contamination. Subsequently, the amounts of heavy metals (Cd, Pb extracted by solution in two steps (HCl, CaCl2 were measured using atomic absorption spectroscopy (AAS. The extracted values indicate what amounts of which elements could be mobilized by human impact and/or production of humic acids, which occasionally emerges during the remediation works. The total heavy metal concentrations in the samples were investigated by X-ray fluorescence method. Based on the investigation, the peatbog is claimed to function as a natural filter.

Comfort Study of Office Buildings with Large Glazed Areas

Directory of Open Access Journals (Sweden)

Violeta Motuzienė

2017-09-01

Full Text Available In the buildings with large glazed areas the biggest problem is the space overheating during the warm season. This causes increased energy demand for cooling. The survey was carried out during the warm and cold seasons in two office buildings with large glazed areas. The methodology was prepared for evaluating indoor climate parameters using objective and subjective evaluation. The measurements have shown that there are problems with lighting in workplaces of both buildings during both the warm and cold seasons. The biggest problem is too dry air during the cold period, an acceptable temperature is also not always in the building No. 2. The survey has shown that some employees are dissatisfied with the indoor climate in the workplace, the bigger dissatisfaction is in building No. 2. Assessing according to the O. Fanger methodology was obtained that the number of PPD is in the normal range during the cold period, whereas close to the limit when the building can not be operated in the warm period.

Effect of soap industry effluents on soil and ground water in Albageir area

International Nuclear Information System (INIS)

Awadalla, S. O.

2004-02-01

This study investigates the effect on soil and ground water produced by the effluent from soap industry discharged from Alsheikh Mustafa Alamin (SMA) factory, in Albageir industrial area, located 45 Km south of Khartoum. Soil samples were taken from the periphery of the effluent pond and from 25 and 50 cm depths from pits at different distances from the pond.The samples were analyzed for the following chemical and physical characteristics PH, EC, sodium, chloride ions and their grain size, in order to investigate any possible soil degradation. The results showed that there is an increase in soil salinity and sodicity resulting from the improper discharge of the liquid waste, and from lack of treatment before the discharge. Hence, there are definitive signs for soil degradation in the study area, which could reach a high magnitude in the long.This situation could be rectified by adopting updated techniques for treatment and disposal of effluent, and by regular inspection, by the authorities in order to make sure that the regulations are not violated. Chemical and physical analyses of ground water samples showed no signs of pollution. However, if the disposal practices are not revised, the possibility of pollution in the near future is likely to occur. A package of measurements is proposed in order to curb the impact of the industry on the environment. (Author)

Highly Enhanced Electromechanical Stability of Large-Area Graphene with Increased Interfacial Adhesion Energy by Electrothermal-Direct Transfer for Transparent Electrodes.

Science.gov (United States)

Kim, Jangheon; Kim, Gi Gyu; Kim, Soohyun; Jung, Wonsuk

2016-09-07

Graphene, a two-dimensional sheet of carbon atoms in a hexagonal lattice structure, has been extensively investigated for research and industrial applications as a promising material with outstanding electrical, mechanical, and chemical properties. To fabricate graphene-based devices, graphene transfer to the target substrate with a clean and minimally defective surface is the first step. However, graphene transfer technologies require improvement in terms of uniform transfer with a clean, nonfolded and nontorn area, amount of defects, and electromechanical reliability of the transferred graphene. More specifically, uniform transfer of a large area is a key challenge when graphene is repetitively transferred onto pretransferred layers because the adhesion energy between graphene layers is too low to ensure uniform transfer, although uniform multilayers of graphene have exhibited enhanced electrical and optical properties. In this work, we developed a newly suggested electrothermal-direct (ETD) transfer method for large-area high quality monolayer graphene with less defects and an absence of folding or tearing of the area at the surface. This method delivers uniform multilayer transfer of graphene by repetitive monolayer transfer steps based on high adhesion energy between graphene layers and the target substrate. To investigate the highly enhanced electromechanical stability, we conducted mechanical elastic bending experiments and reliability tests in a highly humid environment. This ETD-transferred graphene is expected to replace commercial transparent electrodes with ETD graphene-based transparent electrodes and devices such as a touch panels with outstanding electromechanical stability.

Development and Application of Environmental Quality of Life Scale among People Residing near Three Types of Industrial Areas, Southern Thailand

Science.gov (United States)

Sopsuk, Jirawan; Chongsuvivatwong, Virasakdi; Sornsrivichai, Vorasith; Hasuwanakit, Supat

2013-01-01

To compare QOL among rural people living in three different industrial areas and one non-industrial area in southern Thailand. A questionnaire based on the WHOQOL-BREF with environmental assessment was initially developed. After consultation with experts and pilot study, it was tested to check internal reliability and further modified as…

Temporal and spatial changes of microbial community in an industrial effluent receiving area in Hangzhou Bay.

Science.gov (United States)

Zhang, Yan; Chen, Lujun; Sun, Renhua; Dai, Tianjiao; Tian, Jinping; Zheng, Wei; Wen, Donghui

2016-06-01

Anthropogenic activities usually contaminate water environments, and have led to the eutrophication of many estuaries and shifts in microbial communities. In this study, the temporal and spatial changes of the microbial community in an industrial effluent receiving area in Hangzhou Bay were investigated by 454 pyrosequencing. The bacterial community showed higher richness and biodiversity than the archaeal community in all sediments. Proteobacteria dominated in the bacterial communities of all the samples; Marine_Group_I and Methanomicrobia were the two dominant archaeal classes in the effluent receiving area. PCoA and AMOVA revealed strong seasonal but minor spatial changes in both bacterial and archaeal communities in the sediments. The seasonal changes of the bacterial community were less significant than those of the archaeal community, which mainly consisted of fluctuations in abundance of a large proportion of longstanding species rather than the appearance and disappearance of major archaeal species. Temperature was found to positively correlate with the dominant bacteria, Betaproteobacteria, and negatively correlate with the dominant archaea, Marine_Group_I; and might be the primary driving force for the seasonal variation of the microbial community. Copyright © 2016. Published by Elsevier B.V.

Highly Flexible and High-Performance Complementary Inverters of Large-Area Transition Metal Dichalcogenide Monolayers

KAUST Repository

Pu, Jiang

2016-03-23

Complementary inverters constructed from large-area monolayers of WSe2 and MoS2 achieve excellent logic swings and yield an extremely high gain, large total noise margin, low power consumption, and good switching speed. Moreover, the WSe2 complementary-like inverters built on plastic substrates exhibit high mechanical stability. The results provide a path toward large-area flexible electronics. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The large-area CdTe thin film for CdS/CdTe solar cell prepared by physical vapor deposition in medium pressure

Energy Technology Data Exchange (ETDEWEB)

Luo, Run; Liu, Bo; Yang, Xiaoyan; Bao, Zheng; Li, Bing, E-mail: libing70@126.com; Zhang, Jingquan; Li, Wei; Wu, Lili; Feng, Lianghuan

2016-01-01

Graphical abstract: - Highlights: • The large-area CdTe film has been prepared by PVD under the pressure of 0.9 kPa. • The as-prepared CdTe thin film processes excellent photovoltaic properties. • This technique is suitable for depositing large-area CdTe thin film. • The 14.6% champion efficiency CdS/CdTe cell has been achieved. - Abstract: The Cadmium telluride (CdTe) thin film has been prepared by physical vapor deposition (PVD), the Ar + O{sub 2} pressure is about 0.9 kPa. This method is a newer technique to deposit CdTe thin film in large area, and the size of the film is 30 × 40 cm{sup 2}. This method is much different from the close-spaced sublimation (CSS), as the relevance between the source temperature and the substrate temperature is weak, and the gas phase of CdTe is transferred to the substrate by Ar + O{sub 2} flow. Through this method, the compact and uniform CdTe film (30 × 40 cm{sup 2}) has been achieved, and the performances of the CdTe thin film have been determined by transmission spectrum, SEM and XRD. The film is observed to be compact with a good crystallinity, the CdTe is polycrystalline with a cubic structure and a strongly preferred (1 1 1) orientation. Using the CdTe thin film (3 × 5 cm{sup 2}) which is taken from the deposited large-area film, the 14.6% efficiency CdS/CdTe thin film solar cell has been prepared successfully. The structure of the cell is glass/FTO/CdS/CdTe/graphite slurry/Au, short circuit current density (J{sub sc}) of the cell is 26.9 mA/cm{sup 2}, open circuit voltage (V{sub oc}) is 823 mV, and filling factor (FF) is 66.05%. This technique can be a quite promising method to apply in the industrial production, as it has great prospects in the fabricating of large-area CdTe film.

Self-alignment of a compact large-area atomic Sagnac interferometer

International Nuclear Information System (INIS)

Tackmann, G; Berg, P; Schubert, C; Abend, S; Gilowski, M; Ertmer, W; Rasel, E M

2012-01-01

We report on the realization of a compact atomic Mach-Zehnder-type Sagnac interferometer of 13.7 cm length, which covers an area of 19 mm 2 previously reported only for large thermal beam interferometers. According to Sagnac's formula, which holds for both light and atoms, the sensitivity for rotation rates increases linearly with the area enclosed by the interferometer. The use of cold atoms instead of thermal atoms enables miniaturization of Sagnac interferometers without sacrificing large areas. In comparison with thermal beams, slow atoms offer better matching of the initial beam velocity and the velocity with which the matter waves separate. In our case, the area is spanned by a cold atomic beam of 2.79 m s -1 , which is split, deflected and combined by driving a Raman transition between the two hyperfine ground states of 87 Rb in three spatially separated light zones. The use of cold atoms requires a precise angular alignment and high wave front quality of the three independent light zones over the cloud envelope. We present a procedure for mutually aligning the beam splitters at the microradian level by making use of the atom interferometer itself in different configurations. With this method, we currently achieve a sensitivity of 6.1×10 -7 rad s -1 Hz -1/2 . (paper)

Polycyclic aromatic hydrocarbons associated with particles in ambient air from urban and industrial areas

Energy Technology Data Exchange (ETDEWEB)

Rehwagen, Martina; Mueller, Andrea; Herbarth, Olf [UFZ-Centre for Environmental Research Leipzig-Halle, Department of Human Exposure Research and Epidemiology, Permoserstr. 15, D 04318 Leipzig (Germany); Massolo, Laura; Ronco, Alicia [CIMA Centro de Investigaciones del Medio Ambiente, Facultad de Ciencias Exactas, Universidad Nacional de La Plata, 8 Calle 47 y 115, 1900 La Plata (Argentina)

2005-09-15

This study takes into consideration an analysis of the chemical polycyclic aromatic hydrocarbon (PAH) profile and its distribution in inhalable and respirable particulate matter in urban and industrial areas in La Plata, Argentina, and Leipzig, Germany. Representative samples from three locations in La Plata (industrial, traffic influenced and control area) and two locations in Leipzig (traffic influenced and control area) were obtained in summer and winter. The sampling of particulate matter was carried out with high volume collectors using cascade impactors to separate six size fractions. PAHs were extracted with hexane through a solid-liquid equilibrium extraction and analysed by HPLC/UV/fluorescence detection. The results showed a PAH seasonal behaviour in both regions, with lower contents in summer and higher ones in winter. Highest concentrations of total PAHs were found in the industrial area in La Plata. The size distribution of particles demonstrates the greater relevance of smaller particles. More than 50% of PAHs were associated with particles of less than 0.49 {mu}m. Moreover, this particle size fraction was associated with traffic, whereas other sources of combustion were related also to particles between 0.49 and 0.95 {mu}m. Considering the ratio of benzo(ghi)perylene (BgP)/benzo(a)pyrene (BaP) as an indicator for traffic influence, it was observed that La Plata City was more affected than Leipzig by the same proportion in summer and in winter. The BgP/InP (indeno(123-cd)pyrene) ratio was lower in winter than in summer in both places and indicates the presence of domestic combustion sources. It is important to point out the significance of using fingerprint compound ratios to identify possible sources of pollution with PAHs bound to particles.

Ambient air quality at the wider area of an industrial mining facility at Stratoni, Chalkidiki, Greece.

Science.gov (United States)

Gaidajis, Georgios; Angelakoglou, Komninos; Gazea, Emmy

2012-01-01

To assess ambient air quality at the wider area of a mining-industrial facility in Chalkidiki, Greece, the particulate matter with an aerodynamic diameter of 10 μm (PM(10)) and its content in characteristic elements, i.e., As, Cd, Cu, Fe, Mn, Pb, Zn were monitored for a period of three years (2008-2010). Gravimetric air samplers were employed for the particulate matter sampling at three sampling stations located in the immediate vicinity of the industrial facility and at a neighbouring residential site. Monitoring data indicated that the 3-year median PM(10) concentrations were 23.3 μg/m(3) at the residential site close to the facility and 28.7 μg/m(3) at the site within the facility indicating a minimal influence from the industrial activities to the air quality of the neighbouring residential area. Both annual average and median PM(10) concentration levels were below the indicative European standards, whereas similar spatial and temporal variation was observed for the PM(10) constituents. The average Pb concentrations measured for the three sampling sites were 0.2, 0.146 and 0.174 μg/m(3) respectively, well below the indicative limit of 0.5 μg/m(3). The quantitative and qualitative comparison of PM(10) concentrations and its elemental constituent for the three sampling stations did not indicate any direct influence of the mining-industrial activities to the air quality of the Stratoni residential area.

Fitting Irregular Shape Figures into Irregular Shape Areas for the Nesting Problem in the Leather Industry

Directory of Open Access Journals (Sweden)

Guevara-Palma Luis

2015-01-01

Full Text Available The nesting problem of irregular shapes within irregular areas has been studied from several approaches due to their application in different industries. The particular case of cutting leather involves several restrictions that add complexity to this problem, it is necessary to generate products that comply with the quality required by customers This paper presents a methodology for the accommodation of irregular shapes in an irregular area (leather considering the constraints set by the footwear industry, and the results of this methodology when applied by a computer system. The scope of the system is to develop a working prototype that operates under the guidelines of a commercial production line of a sponsor company. Preliminary results got a reduction of 70% of processing time and improvement of 5% to 7% of the area usage when compared with manual accommodation.

The impact of industrial waste of Venezuelan marine water

Energy Technology Data Exchange (ETDEWEB)

Roberts, Frank [Bechtel Corp., Gaithersburg, MD (United States); Guarino, Carmen [Guarino Engineers, Philadelphia, PA (United States); Arias, Marlene [Ministerio del Ambiente y Recursos Naturales Renovables, Caracas (Venezuela)

1994-12-31

The Puerto Cabello-Marron coastal area of Venezuela is an ideal location for industries that require large land areas, water, marine transportation, minimum habitation, cooling water, etc. However, mercury spills have produced concern in the entire coastal zone. The area was investigated and negative impacts were identified. Consequently, recommendations for waste water management were proceeded. 13 refs., 6 figs., 3 tabs.

The impact of industrial waste of Venezuelan marine water

Energy Technology Data Exchange (ETDEWEB)

Roberts, Frank [Bechtel Corp., Gaithersburg, MD (United States); Guarino, Carmen [Guarino Engineers, Philadelphia, PA (United States); Arias, Marlene [Ministerio del Ambiente y Recursos Naturales Renovables, Caracas (Venezuela)

1993-12-31

The Puerto Cabello-Marron coastal area of Venezuela is an ideal location for industries that require large land areas, water, marine transportation, minimum habitation, cooling water, etc. However, mercury spills have produced concern in the entire coastal zone. The area was investigated and negative impacts were identified. Consequently, recommendations for waste water management were proceeded. 13 refs., 6 figs., 3 tabs.

Blood lead level studies by the Public Health Service in an industrial stress area

Energy Technology Data Exchange (ETDEWEB)

Jantzen, G.

1981-12-01

The general directions of the European Community concerning lead resulted to be useful for analysing the biologic impact on the population living in an industrial immission area and for differentiating within this locality affected and non-affected residential districts. Consequently the social-hygienic and regional-hygienic measures are limited and justified territorially. The environmental parameters, their relation to the distance at which an industrial plant is situated and the blood lead values are indicated. Recommendations are given, which concern the protection of health and even the reconstruction of the residential area by immission-reducing measures. It was found that the lead impact on children is higher than that on grown-ups. Tables illustrate the symptomatology of lead impacts, its relation to blood lead concentration, the degree of impact measured in children and grown-ups and the corresponding necessary measures as auxiliary methods for the Public Health Service and the physicians.

Large-area super-resolution optical imaging by using core-shell microfibers

Science.gov (United States)

Liu, Cheng-Yang; Lo, Wei-Chieh

2017-09-01

We first numerically and experimentally report large-area super-resolution optical imaging achieved by using core-shell microfibers. The particular spatial electromagnetic waves for different core-shell microfibers are studied by using finite-difference time-domain and ray tracing calculations. The focusing properties of photonic nanojets are evaluated in terms of intensity profile and full width at half-maximum along propagation and transversal directions. In experiment, the general optical fiber is chemically etched down to 6 μm diameter and coated with different metallic thin films by using glancing angle deposition. The direct imaging of photonic nanojets for different core-shell microfibers is performed with a scanning optical microscope system. We show that the intensity distribution of a photonic nanojet is highly related to the metallic shell due to the surface plasmon polaritons. Furthermore, large-area super-resolution optical imaging is performed by using different core-shell microfibers placed over the nano-scale grating with 150 nm line width. The core-shell microfiber-assisted imaging is achieved with super-resolution and hundreds of times the field-of-view in contrast to microspheres. The possible applications of these core-shell optical microfibers include real-time large-area micro-fluidics and nano-structure inspections.

Optimization of a large integrated area development of gas fields offshore Sarawak, Malaysia

International Nuclear Information System (INIS)

Inyang, S.E.; Tak, A.N.H.; Costello, G.

1995-01-01

Optimizations of field development plans are routine in the industry. The size, schedule and nature of the upstream gas supply project to the second Malaysia LNG (MLNG Dua) plant in Bintulu, Sarawak made the need for extensive optimizations critical to realizing a robust and cost effective development scheme, and makes the work of more general interest. The project comprises the upstream development of 11 offshore fields for gas supply to MLNG Dua plant at an initial plateau production of 7.8 million tons per year of LNG. The gas fields span a large geographical area in medium water depths (up to 440 ft), and contain gas reserves of a distinctly variable gas quality. This paper describes the project optimization efforts aimed to ensure an upstream gas supply system effectiveness of over 99% throughout the project life while maintaining high safety and environmental standards and also achieving an economic development in an era of low hydrocarbon prices. Fifty percent of the first of the three phases of this gas supply project has already been completed and the first gas from these fields is scheduled to be available by the end of 1995

Uncertainty in the Sphere of the Industry 4.0 – Potential Areas to Research

Directory of Open Access Journals (Sweden)

Andrzej Magruk

2016-12-01

Full Text Available The world stands on the threshold of a new age of technology, which will launch a fourth industrial revolution (Industry 4.0. According to this idea, web-based network will support smart factories at every stage of the work on the product, from design through to servicing and recycling. It is a vision of a world in which the real environment connects to the digital one using follows driving forces: Internet of things, cloud computing, big data, cyber-physical systems, and others. The Industry 4.0 concept is based on developing smart chains preparation based on communicating with each other means of production, products, components, plants, humans. Established in Germany, the concept of Industry 4.0, is the brainchild – its beginning reaches 2011. It is therefore fraught with high level of uncertainty in many aspects (economic, social, technological, legal, etc.. The main aim of this article is to analyze different dimensions of uncertainty regarding the Industry 4.0, both in terms of opportunities and threats. Due to the freshness of the topic and the great complexity of the Industry 4.0 phenomenon, the main aim of the article is to identify potential areas requiring the necessary research in order minimizing negative – today uncertain – effects occurring in both the design concept Industry 4.0 as well as during its functioning.

Large area nuclear particle detectors using ET materials

International Nuclear Information System (INIS)

1987-08-01

The purpose of this SBIR Phase 1 feasibility effort was to demonstrate the usefulness of Quantex electron-trapping (ET) materials for spatial detection of nuclear particles over large areas. This demonstration entailed evaluating the prompt visible scintillation as nuclear particles impinged on films of ET materials, and subsequently detecting the nuclear particle impingement information pattern stored in the ET material, by means of the visible-wavelength luminescence produced by near-infrared interrogation. Readily useful levels of scintillation and luminescence outputs are demonstrated

Report on an industrial machinery engineering policy study meeting. Studies on new energy industries; Sangyo kikai engineering seisaku kenkyukai (shin energy sangyo no kenkyu) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-07-01

Effects extended to industrial areas by new energy development were analyzed by using the industrial relation table. Technological development of new energies can mass-produce energy without being restricted by energy resource availability, and retaining manufacturing facilities can exhibit energy reserve function with security. The technologies may be suitable for local energy supply. In the aspects of industrial policies and people's living, demands on diversification and improvement of the people's living may be responded, levels of scientific technologies may be enhanced, and contribution to improving the industrial structure may be expected. The energy industry includes a large number of related industries and has vast related areas. A large number of technology induced effects can be expected in the course of research and development. A market of huge size may be estimated in the future, by which level elevation of the industrial structure would be supported. Early promotion of the new energy development is an urgent assignment for the 1980's. In order to achieve this goal, it is necessary to promote research and development, proliferation and practical application, for which the physical strength of the present Japan must be utilized to its maximum in making human and fund investments. Expansion and improvement in the industrialization infrastructures are also important, whereas the government's subsidies must be increased, and vitality in the private sector must be incorporated into organized force. (NEDO)

Characterisation of large area THGEMs and experimental measurement of the Townsend coefficients for CF4

Science.gov (United States)

Burns, J.; Crane, T.; Ezeribe, A. C.; Grove, C. L.; Lynch, W.; Scarff, A.; Spooner, N. J. C.; Steer, C.

2017-10-01

Whilst the performance of small THGEMs is well known, here we consider the challenges in scaling these up to large area charge readouts. We first verify the expected gain of larger THGEMs by reporting experimental Townsend coefficients for a 10 cm diameter THGEM in low-pressure CF4. Large area 50 cm by 50 cm THGEMs were sourced from a commercial PCB supplier and geometrical imperfections were observed which we quantified using an optical camera setup. The large area THGEMs were experimentally characterised at Boulby Underground Laboratory through a series of gain calibrations and alpha spectrum measurements. ANSYS, Magboltz and Garfield++ simulations of the design of a TPC based on the large area THGEMs are presented. We also consider their implications for directional dark matter research and potential applications within nuclear security.

Evaluating Insects as Bioindicators of Heavy Metal Contamination and Accumulation near Industrial Area of Gujrat, Pakistan.

Science.gov (United States)

Azam, Iqra; Afsheen, Sumera; Zia, Ahmed; Javed, Muqaddas; Saeed, Rashid; Sarwar, Muhammad Kaleem; Munir, Bushra

2015-01-01

To study the accumulation and contamination of heavy metals (i.e., Cd, Cr, Cu, Ni, and Zn) in soil, air, and water, few insect species were assayed as ecological indicators. Study area comes under industrial zone of district Gujrat of Punjab, Pakistan. Insects used as bioindicators included a libellulid dragonfly (Crocothemis servilia), an acridid grasshopper (Oxya hyla hyla), and a nymphalid butterfly (Danaus chrysippus) near industrial zone of Gujrat. Accumulation of Cd was highest in insect species followed by Cu, Cr, Zn, and Ni at p Lepidoptera. The total metal concentrations in insects were pointed significantly higher at sites S3 (Mid of HalsiNala), S9 (End of HalsiNala), and S1 (Start of HalsiNala), whereas lowest value was detected at site S6 (Kalra Khasa) located far from industrial area. HACA indicates that these insect groups are potential indicators of metal contamination and can be used in biomonitoring.

AREAS OF ECONOMIC INFLUENCE OF SUGARCANE INDUSTRY IN MATO GROSSO, 2010.

Directory of Open Access Journals (Sweden)

Wladimir Colman de Azevedo Junior

2015-09-01

Full Text Available The Macroeconomic data reveals the increase of sugarcane chain relevance to Mato Grosso economy, however does not exist studies that evaluate the scope of regional impacts. This research has as the main objective the identification of the territory extension of the sugarcane industry influence in Mato Grosso during 2010, characterizing relationships between industrial plants and the regions where they acting. Was used the gravitational model developed by Isard (1956 to estimate this interrelation commerce patterns of the chain in the state, to find the sugarcane regional centers, as well as, to set up their potential areas of influence. As results has the identification of the 13 cane regions, three cities in first level, seven in the second level and three sub-centers. The relations between this centers and the respective regions has different specifications and their complete understanding allows destination of private investments and public politics. Keywords: Gravitational Model. Cane Sugar Suply Chain. Mato Grosso.

Priority areas for large mammal conservation in Equatorial Guinea.

Directory of Open Access Journals (Sweden)

Mizuki Murai

Full Text Available Hunting is one of the main driving forces behind large mammal density distribution in many regions of the world. In tropical Africa, urban demand for bushmeat has been shown to dominate over subsistence hunting and its impact often overrides spatial-ecological species characteristics. To effectively protect remaining mammal populations the main factors that influence their distribution need to be integrated into conservation area prioritisation and management plans. This information has been lacking for Río Muni, Equatorial Guinea, as prior studies have been outdated or have not systematically covered the continental region of the country. In this study we evaluated: 1 the relative importance of local vs. commercial hunting; 2 wildlife density of protected vs. non-protected areas; and 3 the importance of ecological factors vs. human influence in driving mammal density distribution in Río Muni. We adopted a systematic countrywide line transect approach with particular focus on apes and elephants, but also including other mammal species. For analysis of field data we used generalised linear models with a set of predictor variables representing ecological conditions, anthropogenic pressure and protected areas. We estimate that there are currently 884 (437-1,789 elephants and 11,097 (8,719-13,592 chimpanzees and gorillas remaining in Río Muni. The results indicate strong hunting pressures on both local and commercial levels, with roads demonstrating a negative impact on elephants and overall mammal body mass. Protected areas played no role in determining any of the mammal species distributions and significant human hunting signs were found inside these protected areas, illustrating the lack of environmental law enforcement throughout the country. Río Muni is currently under-represented in conservation efforts in Western Equatorial Africa, and we recommend a focus on cross-boundary conservation, in particular in the Monte Alén-Monts de Cristal

Priority areas for large mammal conservation in Equatorial Guinea.

Science.gov (United States)

Murai, Mizuki; Ruffler, Heidi; Berlemont, Antoine; Campbell, Genevieve; Esono, Fidel; Agbor, Anthony; Mbomio, Domingo; Ebana, Agustín; Nze, Antonio; Kühl, Hjalmar S

2013-01-01

Hunting is one of the main driving forces behind large mammal density distribution in many regions of the world. In tropical Africa, urban demand for bushmeat has been shown to dominate over subsistence hunting and its impact often overrides spatial-ecological species characteristics. To effectively protect remaining mammal populations the main factors that influence their distribution need to be integrated into conservation area prioritisation and management plans. This information has been lacking for Río Muni, Equatorial Guinea, as prior studies have been outdated or have not systematically covered the continental region of the country. In this study we evaluated: 1) the relative importance of local vs. commercial hunting; 2) wildlife density of protected vs. non-protected areas; and 3) the importance of ecological factors vs. human influence in driving mammal density distribution in Río Muni. We adopted a systematic countrywide line transect approach with particular focus on apes and elephants, but also including other mammal species. For analysis of field data we used generalised linear models with a set of predictor variables representing ecological conditions, anthropogenic pressure and protected areas. We estimate that there are currently 884 (437-1,789) elephants and 11,097 (8,719-13,592) chimpanzees and gorillas remaining in Río Muni. The results indicate strong hunting pressures on both local and commercial levels, with roads demonstrating a negative impact on elephants and overall mammal body mass. Protected areas played no role in determining any of the mammal species distributions and significant human hunting signs were found inside these protected areas, illustrating the lack of environmental law enforcement throughout the country. Río Muni is currently under-represented in conservation efforts in Western Equatorial Africa, and we recommend a focus on cross-boundary conservation, in particular in the Monte Alén-Monts de Cristal and Río Campo

Dynamic of pollutants concentration in forest stands from Copsa Mica industrial area

Directory of Open Access Journals (Sweden)

Marian Ianculescu

2009-11-01

Full Text Available The paper presents the dynamics of pollutants concentrations from nonferrous metallurgical plant in Copºa Mica, considered, between the years 1985 -1989, as the most polluted area, even in the world, and detected as a large black spot on Landsat satellite imagery.Returning to investigations in this area, after 20-25 years, the pollution activity was changed after 1990, as a consequence of the reductionof industrial capacity, including the black smoke plant decommissioning, and the chimney built for exhaust pollutants over 350 m feet high, resulted some conclusions, necessary for decisions that have to be taken by environmental, forestry, health andagriculture authorities.The litter, soil and vegetation samples were colected from the same permanent sample plots between the years 2006-2009, as between the years 1985-1989, using the same methods, in order to be compared and analyzed. Therefore, returning to investigations in these permanent sample plots, were found the following conclusions: i between the period 1985 - 1989, in all examined cases were revealed high pollutants concentrations, even exceeding the maximum allowable limit (MAL consisting of suphur compounds in synergistic action with heavy metals(Cu, Pb, Cd, Zn, Mn, etc., in vegetation and litter, which was directly correlatedwith noxious concentrations in the air, and concentrations below MAL in soil samples; ii contrary, regarding the new pollution activity, it has been revealed low noxious concentration, in vegetation, litter and soil samples collected during the period between the years 2006-2008, which are directly related to their low concentrationlevel in the air. Due to pollutants accumulation phenomenon over the years, high pollutants concentrations, ten times higher than MAL, were found in the superior soil layer. In such circumstances the best solution to protect the environment, population and livestock of the damaged area, for tens of thousands of hectares, is the closure

Cleanup of large areas contaminated as a result of a nuclear accident

International Nuclear Information System (INIS)

1989-01-01

The purposes of the report are to provide an overview of the methodology and technology available to clean up contaminated areas and to give preliminary guidance on matters related to the planning, implementation and management of such cleanups. This report provides an integrated overview of important aspects related to the cleanup of very large areas contaminated as a result of a serious nuclear accident, including information on methods and equipment available to: characterize the affected area and the radioactive fallout; stabilize or isolate the contamination; and clean up contaminated urban, rural and forested areas. The report also includes brief sections on planning and management considerations and the transport and disposal of the large volumes of wastes arising from such cleanups. For the purposes of this report, nuclear accidents which could result in the deposition of decontamination over large areas if the outer containment fails badly include: 1) An accident with a nuclear weapon involving detonation of the chemical high explosive but little, if any, nuclear fission. 2) A major loss of medium/high level liquid waste (HLLW) due to an explosion/fire at a storage site for such waste. 3) An accident at a nuclear power plant (NPP), for example a loss of coolant accident, which results in some core disruption and fuel melting. 4) An accident at an NPP involving an uncontrolled reactivity excursion resulting in the violent ejection of a reactor core material and rupture of the containment building. 117 refs, 32 figs, 12 tabs

The impact of industrial anthropization on mosquito (Diptera, Culicidae) communities in mangrove areas of Guanabara Bay (Rio de Janeiro, Brazil).

Science.gov (United States)

de Souza, A S; Couri, M S; Florindo, L

2012-02-01

The effects of industrial anthropization on species composition and community diversity of Culicidae (Diptera) were studied in a mangrove area impacted by industrial activities as compared to a preserved area, both around Guanabara Bay in the state of Rio de Janeiro, Brazil. Diversity, equitability, and species richness in Culicidae community differed between the studied areas. Indicator species analysis and correspondence analysis were carried out and indicated that the Sabethini, especially Wyeomyia (Phoniomyia) theobaldi Lane, Wyeomyia (Phoniomyia) fuscipes (Edwards), and a non-identified species of Wyeomyia sp. were associated to the preserved area, whereas Aedes taeniorhynchus Wiedemann and Aedes scapularis (Rondani) to the impacted area.

Large-Area Synthesis of High-Quality Uniform Few-Layer MoTe2.

Science.gov (United States)

Zhou, Lin; Xu, Kai; Zubair, Ahmad; Liao, Albert D; Fang, Wenjing; Ouyang, Fangping; Lee, Yi-Hsien; Ueno, Keiji; Saito, Riichiro; Palacios, Tomás; Kong, Jing; Dresselhaus, Mildred S

2015-09-23

The controlled synthesis of large-area, atomically thin molybdenum ditelluride (MoTe2) crystals is crucial for its various applications based on the attractive properties of this emerging material. In this work, we developed a chemical vapor deposition synthesis to produce large-area, uniform, and highly crystalline few-layer 2H and 1T' MoTe2 films. It was found that these two different phases of MoTe2 can be grown depending on the choice of Mo precursor. Because of the highly crystalline structure, the as-grown few-layer 2H MoTe2 films display electronic properties that are comparable to those of mechanically exfoliated MoTe2 flakes. Our growth method paves the way for the large-scale application of MoTe2 in high-performance nanoelectronics and optoelectronics.

Position reconstruction in large-area scintillating fibre detectors

Energy Technology Data Exchange (ETDEWEB)

Mahata, K. [Gesellschaft fuer Schwerionenforschung (GSI), D-64291 Darmstadt (Germany); Nuclear Physics Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)], E-mail: kmahata@barc.gov.in; Johansson, H.T. [Gesellschaft fuer Schwerionenforschung (GSI), D-64291 Darmstadt (Germany); Department of Fundamental Physics, Chalmers University of Technology, S-412 96 Goeteborg (Sweden); Paschalis, S. [Department of Physics, University of Liverpool, Oliver Lodge Laboratory, L69 7ZE (United Kingdom); Simon, H.; Aumann, T. [Gesellschaft fuer Schwerionenforschung (GSI), D-64291 Darmstadt (Germany)

2009-09-11

A new analysis procedure has been developed for the large-area scintillating fibre detectors with position-sensitive photomultiplier (PSPM) readout used for heavy ions in the LAND set-up at GSI. It includes gain matching of the PSPM, calibration of the PSPM fibre mask and hit reconstruction. This procedure allows for a quasi-online calibration of this tracking device. It also allows for a precise determination of the position close to the intrinsic detector resolution of 1 mm pitch together with careful treatment of individual event accuracies.

Chemical hole doping into large-area transition metal dichalcogenide monolayers using boron-based oxidant

KAUST Repository

Matsuoka, Hirofumi; Kanahashi, Kaito; Tanaka, Naoki; Shoji, Yoshiaki; Li, Lain-Jong; Pu, Jiang; Ito, Hiroshi; Ohta, Hiromichi; Fukushima, Takanori; Takenobu, Taishi

2018-01-01

Hole carrier doping into single-crystalline transition metal dichalcogenide (TMDC) films can be achieved with various chemical reagents. However, large-area polycrystalline TMDC monolayers produced by a chemical vapor deposition (CVD) growth method have yet to be chemically doped. Here, we report that a salt of a two-coordinate boron cation, Mes2B+ (Mes: 2,4,6-trimethylphenyl group), with a chemically stable tetrakis(pentafluorophenyl)borate anion, [(C6F5)4B]−, can serve as an efficient hole-doping reagent for large-area CVD-grown tungsten diselenide (WSe2) films. Upon doping, the sheet resistance of large-area polycrystalline WSe2 monolayers decreased from 90 GΩ/sq to 3.2 kΩ/sq.

Chemical hole doping into large-area transition metal dichalcogenide monolayers using boron-based oxidant

KAUST Repository

Matsuoka, Hirofumi

2018-01-18

Hole carrier doping into single-crystalline transition metal dichalcogenide (TMDC) films can be achieved with various chemical reagents. However, large-area polycrystalline TMDC monolayers produced by a chemical vapor deposition (CVD) growth method have yet to be chemically doped. Here, we report that a salt of a two-coordinate boron cation, Mes2B+ (Mes: 2,4,6-trimethylphenyl group), with a chemically stable tetrakis(pentafluorophenyl)borate anion, [(C6F5)4B]−, can serve as an efficient hole-doping reagent for large-area CVD-grown tungsten diselenide (WSe2) films. Upon doping, the sheet resistance of large-area polycrystalline WSe2 monolayers decreased from 90 GΩ/sq to 3.2 kΩ/sq.

Internal quality evolution of a large test system – an industrial study

Directory of Open Access Journals (Sweden)

Kovács Attila

2016-12-01

Full Text Available This paper presents our empirical observations related to the evolution of a large automated test system. The system observed is used in the industry as a test tool for complex telecommunication systems, itself consisting of more than one million lines of source code. This study evaluates how different changes during the development have changed the number of observed Code Smells in the test system. We have monitored the development of the test scripts and measured the code quality characteristics over a five years period.

Residents' Self-Reported Health Effects and Annoyance in Relation to Air Pollution Exposure in an Industrial Area in Eastern-Estonia.

Science.gov (United States)

Orru, Hans; Idavain, Jane; Pindus, Mihkel; Orru, Kati; Kesanurm, Kaisa; Lang, Aavo; Tomasova, Jelena

2018-02-02

Eastern Estonia has large oil shale mines and industrial facilities mainly focused on electricity generation from oil shale and shale oil extraction, which produce high air pollution emissions. The "Study of the health impact of the oil shale sector-SOHOS" was aimed at identifying the impacts on residents' health and annoyance due to the industrial processing. First, a population-wide survey about health effects and annoyance was carried out. Second, the total and oil shale sectors' emitted concentrations of benzene, phenol, and PM 2.5 were modelled. Third, the differences between groups were tested and relationships between health effects and environmental pollution studied using multiple regression analysis. Compared to the control groups from non-industrial areas in Tartu or Lääne-Viru, residents of Ida-Viru more frequently ( p sector. Next to direct health effects, up to a quarter of the residents of Ida-Viru County were highly annoyed about air pollution. Perceived health risk from air pollution increased the odds of being annoyed. Annoyed people in Ida-Viru had significantly higher odds of experiencing respiratory symptoms during the last 12 months, e.g., wheezing (2.30, 1.31-4.04), chest tightness (2.88, 1.91-4.33 or attack of coughing (1.99, 1.34-2.95).

The potential for ore, industrial minerals and commercial stones in the Simpevarp area

International Nuclear Information System (INIS)

Lindroos, Hardy

2004-10-01

On behalf of SKB (the Swedish Nuclear Fuel and Waste Management Company), a survey has been made of existing information concerning the potential for ore, industrial minerals and commercial stones in and around the two candidate areas for a deep repository in Oskarshamn. A deep repository for spent nuclear fuel should not be located in a rock type or in an area where mineral extraction might be considered in the future, since this would make it difficult or impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities.The survey has made use of the geoscientific information compiled in the more regional investigations in Oskarshamn Municipality in 1998-99. The new information after the municipal study includes extensive geophysical measurements from both the air and the ground. The results of the recently completed geophysical helicopter survey of the Simpevarp area are presented in a special chapter. The judgement of an area's ore potential is in part based on the evaluation of these geophysical measurements. In order to be better able to judge the ore potential, a geochemical investigation of soil samples, including reanalysing of older samples collected by the Geological Survey of Sweden (SGU), has been carried out. The report also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. In cooperation with SGU a mineral resource map of the Simpevarp area has been prepared. The map shows two areas with a potential for commercial stones, namely the granites at Goetemar and Uthammar, situated in the northernmost respectively the southernmost part of the study area. Furthermore, the Goetemar granite has probably a small potential for ores containing tin (Sn) and/or wolfram (W). Although no mineralizations of this type have so far been found, the Goetemar granite area may be unsuitable or for

The potential for ore, industrial minerals and commercial stones in the Simpevarp area

Energy Technology Data Exchange (ETDEWEB)

Lindroos, Hardy [MIRAB Mineral Resurser AB, Uppsla (Sweden)

2004-10-01

On behalf of SKB (the Swedish Nuclear Fuel and Waste Management Company), a survey has been made of existing information concerning the potential for ore, industrial minerals and commercial stones in and around the two candidate areas for a deep repository in Oskarshamn. A deep repository for spent nuclear fuel should not be located in a rock type or in an area where mineral extraction might be considered in the future, since this would make it difficult or impossible to exploit this natural resource. Avoiding such areas reduces the risk that people in the future will come into contact with the deep repository through mineral prospecting or mining activities.The survey has made use of the geoscientific information compiled in the more regional investigations in Oskarshamn Municipality in 1998-99. The new information after the municipal study includes extensive geophysical measurements from both the air and the ground. The results of the recently completed geophysical helicopter survey of the Simpevarp area are presented in a special chapter. The judgement of an area's ore potential is in part based on the evaluation of these geophysical measurements. In order to be better able to judge the ore potential, a geochemical investigation of soil samples, including reanalysing of older samples collected by the Geological Survey of Sweden (SGU), has been carried out. The report also discusses prospecting efforts in the area as well as relevant Swedish mining legislation. In cooperation with SGU a mineral resource map of the Simpevarp area has been prepared. The map shows two areas with a potential for commercial stones, namely the granites at Goetemar and Uthammar, situated in the northernmost respectively the southernmost part of the study area. Furthermore, the Goetemar granite has probably a small potential for ores containing tin (Sn) and/or wolfram (W). Although no mineralizations of this type have so far been found, the Goetemar granite area may be unsuitable or

Large-area uniform electron doping of graphene by Ag nanofilm

Directory of Open Access Journals (Sweden)

Xiaopeng Guo

2017-04-01

Full Text Available Graphene has attracted much attention at various research fields due to its unique optical, electronic and mechanical properties. Up to now, graphene has not been widely used in optoelectronic fields due to the lack of large-area uniform doped graphene (n-doped and p-doped with smooth surface. Therefore, it is rather desired to develop some effective doping methods to extend graphene to optoelectronics. Here we developed a novel doping method to prepare large-area (> centimeter scale uniform doped graphene film with a nanoscale roughness(RMS roughness ∼1.4 nm, the method (nano-metal film doping method is simple but effective. Using this method electron doping (electron-injection may be easily realized by the simple thermal deposition of Ag nano-film on a transferred CVD graphene. The doping effectiveness has been proved by Raman spectroscopy and spectroscopic ellipsometry. Importantly, our method sheds light on some potential applications of graphene in optoelectronic devices such as photodetectors, LEDs, phototransistors, solar cells, lasers etc.

High Energy Astrophysics with the Fermi Large Area Telescope

Science.gov (United States)

Hays, Elizabeth

2009-01-01

This slide presentation reviews some of the findings of the Large Area Telescope (LAT) aboard the Fermi Observatory. It includes information about the LAT, and the Gamma-Ray Burst Monitor (GBM), detection of the quiet sun and the moon in gamma rays, Pulsars observed by the observatory, Globular Star Clusters, Active Galactic Nucleus, and Gamma-Ray Bursts, with specific information about GRB 080916C.

The World Health Organization and the Pharmaceutical Industry. Common areas of interest and differing views.

Science.gov (United States)

Hardwicke, Caroline J

2002-01-01

No article published in the scientific press in the last 10 years reviews the various areas of interest common to the World Health Organization (WHO) and the pharmaceutical industry. Despite a vast amount of information in the public domain, the policies expound the views only of the bodies they represent rather than comparing differing views. An understanding of the factors which affect the interaction between these organisations as well as the organisational structures and the actual areas of intersecting interest, may help to find ways for the industry to assist the WHO in its endeavours in developing countries. Modern drug development is performed initially in and for western society, leaving the areas of infectious or tropical diseases with relatively less industry investment than cancer and cardiovascular disorders. Aspects of the development of an ethical drug, regardless of its therapeutic class (selection of drug name, intellectual property rights, drug safety, marketing and pricing, quality assurance and counterfeiting, generic use, emerging drug donations) are influenced to varying degrees by the triad of money, politics and medical need and the perspectives (each defensible) placed thereon by the WHO and industry. Instead of simply defending their positions combining the best of these strategies to optimise drug development for the needs of developing countries appears logical. Similarly, via its philanthropic initiatives, industry will have donated over $US1 billion in drug and research aid in the period 1995 to 2005. These charitable projects should yield useful information for planning and organising future aid efforts. Global warming, only recently given serious governmental consideration, is an area not yet addressed in drug development policy although along with geographical effects, it is likely to have an impact on the epidemiology of diseases e.g. malaria returning to the Mediterranean, worldwide. With changing disease patterns (and

On the stability of large-area Al-p-Si junction

International Nuclear Information System (INIS)

Tsyganov, Yu.S.

2006-01-01

Design of silicon radiation detector made of 12 kΩ · cm p-silicon with both amine- and amine-free hardeners epoxy resin junction edge passivation is presented. Before producing large-area detectors for measurements of efficiency of evaporation residues collection at the focal plane of the Dubna Gas-Filled Recoil Separator (DGFRS), a set of small-area test detectors was produced. Stability of the Al-(p)Si junction has been studied for a long time. Estimate of a realistic lifetime for the mentioned type of Al-Si rectifying junction is done

A large area two-dimensional position sensitive multiwire proportional detector

CERN Document Server

Moura, M M D; Souza, F A; Alonso, E E; Fujii, R J; Meyknecht, A B; Added, N; Aissaoui, N; Cardenas, W H Z; Ferraretto, M D; Schnitter, U; Szanto, E M; Szanto de Toledo, A; Yamamura, M S; Carlin, N

1999-01-01

Large area two-dimensional position sensitive multiwire proportional detectors were developed to be used in the study of light heavy-ion nuclear reactions at the University of Sao Paulo Pelletron Laboratory. Each detector has a 20x20 cm sup 2 active area and consists of three grids (X-position, anode and Y-position) made of 25 mu m diameter gold plated tungsten wires. The position is determined through resistive divider chains. Results for position resolution, linearity and efficiency as a function of energy and position for different elements are reported.

Canopy area of large trees explains aboveground biomass variations across neotropical forest landscapes

Science.gov (United States)

Meyer, Victoria; Saatchi, Sassan; Clark, David B.; Keller, Michael; Vincent, Grégoire; Ferraz, António; Espírito-Santo, Fernando; d'Oliveira, Marcus V. N.; Kaki, Dahlia; Chave, Jérôme

2018-06-01

Large tropical trees store significant amounts of carbon in woody components and their distribution plays an important role in forest carbon stocks and dynamics. Here, we explore the properties of a new lidar-derived index, the large tree canopy area (LCA) defined as the area occupied by canopy above a reference height. We hypothesize that this simple measure of forest structure representing the crown area of large canopy trees could consistently explain the landscape variations in forest volume and aboveground biomass (AGB) across a range of climate and edaphic conditions. To test this hypothesis, we assembled a unique dataset of high-resolution airborne light detection and ranging (lidar) and ground inventory data in nine undisturbed old-growth Neotropical forests, of which four had plots large enough (1 ha) to calibrate our model. We found that the LCA for trees greater than 27 m (˜ 25-30 m) in height and at least 100 m2 crown size in a unit area (1 ha), explains more than 75 % of total forest volume variations, irrespective of the forest biogeographic conditions. When weighted by average wood density of the stand, LCA can be used as an unbiased estimator of AGB across sites (R2 = 0.78, RMSE = 46.02 Mg ha-1, bias = -0.63 Mg ha-1). Unlike other lidar-derived metrics with complex nonlinear relations to biomass, the relationship between LCA and AGB is linear and remains unique across forest types. A comparison with tree inventories across the study sites indicates that LCA correlates best with the crown area (or basal area) of trees with diameter greater than 50 cm. The spatial invariance of the LCA-AGB relationship across the Neotropics suggests a remarkable regularity of forest structure across the landscape and a new technique for systematic monitoring of large trees for their contribution to AGB and changes associated with selective logging, tree mortality and other types of tropical forest disturbance and dynamics.

Mapping regional patterns of large forest fires in Wildland-Urban Interface areas in Europe.

Science.gov (United States)

Modugno, Sirio; Balzter, Heiko; Cole, Beth; Borrelli, Pasquale

2016-05-01

Over recent decades, Land Use and Cover Change (LUCC) trends in many regions of Europe have reconfigured the landscape structures around many urban areas. In these areas, the proximity to landscape elements with high forest fuels has increased the fire risk to people and property. These Wildland-Urban Interface areas (WUI) can be defined as landscapes where anthropogenic urban land use and forest fuel mass come into contact. Mapping their extent is needed to prioritize fire risk control and inform local forest fire risk management strategies. This study proposes a method to map the extent and spatial patterns of the European WUI areas at continental scale. Using the European map of WUI areas, the hypothesis is tested that the distance from the nearest WUI area is related to the forest fire probability. Statistical relationships between the distance from the nearest WUI area, and large forest fire incidents from satellite remote sensing were subsequently modelled by logistic regression analysis. The first European scale map of the WUI extent and locations is presented. Country-specific positive and negative relationships of large fires and the proximity to the nearest WUI area are found. A regional-scale analysis shows a strong influence of the WUI zones on large fires in parts of the Mediterranean regions. Results indicate that the probability of large burned surfaces increases with diminishing WUI distance in touristic regions like Sardinia, Provence-Alpes-Côte d'Azur, or in regions with a strong peri-urban component as Catalunya, Comunidad de Madrid, Comunidad Valenciana. For the above regions, probability curves of large burned surfaces show statistical relationships (ROC value > 0.5) inside a 5000 m buffer of the nearest WUI. Wise land management can provide a valuable ecosystem service of fire risk reduction that is currently not explicitly included in ecosystem service valuations. The results re-emphasise the importance of including this ecosystem service

[100] or [110] aligned, semiconductor-based, large-area, flexible, electronic devices

Science.gov (United States)

Goyal, Amit

2015-03-24

Novel articles and methods to fabricate the same resulting in flexible, large-area, [100] or [110] textured, semiconductor-based, electronic devices are disclosed. Potential applications of resulting articles are in areas of photovoltaic devices, flat-panel displays, thermophotovoltaic devices, ferroelectric devices, light emitting diode devices, computer hard disc drive devices, magnetoresistance based devices, photoluminescence based devices, non-volatile memory devices, dielectric devices, thermoelectric devices and quantum dot laser devices.

High safety in the mining industry

Energy Technology Data Exchange (ETDEWEB)

1987-08-01

Presents an interview in question and answer format with the deputy chairman of Gosgortekhnadzor (Committee for Supervision of Industrial Work Safety and Mining Supervision) in which he discusses two recent fatal accidents in the Yasinovskaya-Glubokaya and Chaikino coal mines and identifies areas where safety needs to be improved (more automation, protective devices, ventilation etc.). Discusses the particular problems involved with deep mining (20% of mines are now deeper than 700 m and 27 mines are deeper than 1000 m), such as fires, dust, methane, rock falls, insufficient maintenance and strata control and poor ventilation. Confirms that a large number of accidents is due to poor organization and stresses the fact the coal industry must be subjected to perestroika (restructuring) as much as other areas of society.

Assessment of Respiratory Function in Students, Residing in Different Industrial Areas

Directory of Open Access Journals (Sweden)

Aiman E. Konkabaeva

2013-01-01

Full Text Available The article considers the results of the examination of three groups of apparently healthy volunteer students of one social group, both men and women, without bad habits, aged 19-22. Students live in three different industrial areas of Central Khazakhstan, containing ironworks (Temirtau and non-ferrous smelters (Balkhash, Zhezkazgan. It determined the necessity of respiratory function examination, using automated lung tester. The examination of respiratory function determined the decrease of the following parameters: lung vital capacity, maximal expiratory flow volume, forced expiratory volume 1, peak expiratory flow rate, cardiac minute output 25-50 if compared to proper parameters. The examination enabled us to make the conclusion that respiratory function is restricted due to high respiratory load, caused by air pollution. Changes intensity is different and can indicate the pollution in the examined areas.

Tianmujian caldera. A potential area for locating rich and large uranium deposit

International Nuclear Information System (INIS)

Lin Ziyu; Xu Jinshan; Chen Mingzhuo; Jiang Jinyuan; Fan Honghai; Cheng Qi

2001-01-01

Based on the comprehensive analysis on geologic, remote sensing, gravimetric, magnetic and geochemical data, and the field geologic investigation, the author has preliminarily ascertained the formation and the distribution characteristics of the Tianmujian caldera, and recognized the porphyroclastic lava system which is extensively distributed in the area. The authors suggest that the Tianmujian volcanic basin experienced two evolution stages--the thermal uplifting and the formation of caldera, that large concealed uranium-rich granitic massif occurs in the area, and during the vertical evolution process the uranium showed its concentration in the lower part and depletion in the upper part, and large amount of ore-forming material moved upward along with the magmatic hydrothermals entering the caldera to form uranium deposit. In addition, it is clarified that the NE-NW rhombic-formed basement structural pattern is predominated by the NE-trending fault. At the same time, the important role of the basement faults in controlling the magmatic activities, in the formation of volcanic basins, as well as the formation of uranium mineralization is emphasized. On the basis of the above comprehensive analysis the authors suggest that the Tianmujian caldera is a quite favourable potential area for possessing the basic conditions necessary for the formation of rich and large uranium deposit including uranium 'source, migration, concentration, preservation' and favourable multiple metallogenic information is displayed in the Tianmujian area

Evaluating Insects as Bioindicators of Heavy Metal Contamination and Accumulation near Industrial Area of Gujrat, Pakistan

Directory of Open Access Journals (Sweden)

Iqra Azam

2015-01-01

Full Text Available To study the accumulation and contamination of heavy metals (i.e., Cd, Cr, Cu, Ni, and Zn in soil, air, and water, few insect species were assayed as ecological indicators. Study area comes under industrial zone of district Gujrat of Punjab, Pakistan. Insects used as bioindicators included a libellulid dragonfly (Crocothemis servilia, an acridid grasshopper (Oxya hyla hyla, and a nymphalid butterfly (Danaus chrysippus near industrial zone of Gujrat. Accumulation of Cd was highest in insect species followed by Cu, Cr, Zn, and Ni at p<0.05. Hierarchical cluster analysis (HACA was carried out to study metal accumulation level in all insects. Correlation and regression analysis confirmed HACA observations and declared concentration of heavy metals above permissible limits. Metal concentrations in insects were significantly higher near industries and nallahs in Gujrat and relatively higher concentrations of metals were found in Orthoptera than Odonata and Lepidoptera. The total metal concentrations in insects were pointed significantly higher at sites S3 (Mid of HalsiNala, S9 (End of HalsiNala, and S1 (Start of HalsiNala, whereas lowest value was detected at site S6 (Kalra Khasa located far from industrial area. HACA indicates that these insect groups are potential indicators of metal contamination and can be used in biomonitoring.

Large-area Fabry-Perot modulator based on electro-optic polymers

DEFF Research Database (Denmark)

Benter, Nils; Bertram, Ralph Peter; Soergel, Elisabeth

2006-01-01

We present a large-area electro-optic Fabry-Perot modulator utilizing a photoaddressable bis-azo polymer placed between two dielectric mirrors with an open aperture of 2 cm. A modulation efficientcy of 1% at an effective modulation voltage of 20 V for a wavelength of 1.55 mymeter is demonstrated...

Scaling of the Urban Water Footprint: An Analysis of 65 Mid- to Large-Sized U.S. Metropolitan Areas

Science.gov (United States)

Mahjabin, T.; Garcia, S.; Grady, C.; Mejia, A.

2017-12-01

Scaling laws have been shown to be relevant to a range of disciplines including biology, ecology, hydrology, and physics, among others. Recently, scaling was shown to be important for understanding and characterizing cities. For instance, it was found that urban infrastructure (water supply pipes and electrical wires) tends to scale sublinearly with city population, implying that large cities are more efficient. In this study, we explore the scaling of the water footprint of cities. The water footprint is a measure of water appropriation that considers both the direct and indirect (virtual) water use of a consumer or producer. Here we compute the water footprint of 65 mid- to large-sized U.S. metropolitan areas, accounting for direct and indirect water uses associated with agricultural and industrial commodities, and residential and commercial water uses. We find that the urban water footprint, computed as the sum of the water footprint of consumption and production, exhibits sublinear scaling with an exponent of 0.89. This suggests the possibility of large cities being more water-efficient than small ones. To further assess this result, we conduct additional analysis by accounting for international flows, and the effects of green water and city boundary definition on the scaling. The analysis confirms the scaling and provides additional insight about its interpretation.

23 CFR 750.706 - Sign control in zoned and unzoned commercial and industrial areas.

Science.gov (United States)

2010-04-01

... TRANSPORTATION RIGHT-OF-WAY AND ENVIRONMENT HIGHWAY BEAUTIFICATION Outdoor Advertising Control § 750.706 Sign... spacing of outdoor advertising signs located in commercial or industrial zoned or unzoned areas, as... back-to-back or “V” type signs. (c) Where the agreement and State law permits control by local zoning...

A Novel Method of Fabricating Flexible Transparent Conductive Large Area Graphene Film

International Nuclear Information System (INIS)

Fan Tian-Ju; Yuan Chun-Qiu; Tang Wei; Tong Song-Zhao; Huang Wei; Min Yong-Gang; Liu Yi-Dong; Epstein, Arthur J.

2015-01-01

We fabricate flexible conductive and transparent graphene films on position-emission-tomography substrates and prepare large area graphene films by graphite oxide sheets with the new technical process. The multi-layer graphene oxide sheets can be chemically reduced by HNO 3 and HI to form a highly conductive graphene film on a substrate at lower temperature. The reduced graphene oxide sheets show a high conductivity sheet with resistance of 476 Ω/sq and transmittance of 76% at 550 nm (6 layers). The technique used to produce the transparent conductive graphene thin film is facile, inexpensive, and can be tunable for a large area production applied for electronics or touch screens. (paper)

A facility for the test of large area muon chambers at high rates

CERN Document Server

Agosteo, S; Belli, G; Bonifas, A; Carabelli, V; Gatignon, L; Hessey, N P; Maggi, M; Peigneux, J P; Reithler, H; Silari, Marco; Vitulo, P; Wegner, M

2000-01-01

Operation of large area muon detectors at the future Large Hadron Collider (LHC) will be characterized by large sustained hit rates over the whole area, reaching the range of kHz/\\scm. We describe a dedicated test zone built at CERN to test the performance and the aging of the muon chambers currently under development. A radioactive source delivers photons causing the sustained rate of random hits, while a narrow beam of high energy muons is used to directly calibrate the detector performance. A system of remotely controlled lead filters serves to vary the rate of photons over four orders of magnitude, to allow the study of performance as a function of rate.

A facility for the test of large-area muon chambers at high rates

Energy Technology Data Exchange (ETDEWEB)

Agosteo, S.; Altieri, S.; Belli, G.; Bonifas, A.; Carabelli, V.; Gatignon, L.; Hessey, N.; Maggi, M.; Peigneux, J.-P.; Reithler, H. E-mail: hans.reithler@cern.ch; Silari, M.; Vitulo, P.; Wegner, M

2000-09-21

Operation of large-area muon detectors at the future Large Hadron Collider (LHC) will be characterized by large sustained hit rates over the whole area, reaching the range of kHz cm{sup -2}. We describe a dedicated test zone built at CERN to test the performance and the aging of the muon chambers currently under development. A radioactive source delivers photons causing the sustained rate of random hits, while a narrow beam of high-energy muons is used to directly calibrate the detector performance. A system of remotely controlled lead filters serves to vary the rate of photons over four orders of magnitude, to allow the study of performance as a function of rate. (authors)

Crowding-out effect of coal industry investment in coal mining area: taking Shanxi province in China as a case.

Science.gov (United States)

Li, Li; Lei, Yalin; Xu, Qun; Wu, Sanmang; Yan, Dan; Chen, Jiabin

2017-10-01

The rapid development of coal industry in Shanxi province in China has important effects on its economic development. A large amount of money has been invested into the coal industry and other related industries during the recent years. However, research on the investment effect of Shanxi's coal industry was rare. In order to analyze the investment effect of coal industry, based on the crowding-out effect model, cointegration test, and the data available in Shanxi Statistical Yearbooks, this paper calculates the effect between coal industry investment and other 17 industry investment. The results show that the investment of coal industry produces crowding-out effect on food industry, building materials industry, and machinery industry. Increasing 1% of the coal industry investment can reduce 0.25% of the food industry investment, or 0.6% of building materials industry investment, or 0.52% of the machinery industry investment, which implies that Shanxi province should adjust coal industrial structure, promote the balance development of coal industry and other industries, so as to promote its economic growth.

Report on an industrial machinery engineering policy study meeting. Studies on new energy industries; Sangyo kikai engineering seisaku kenkyukai (shin energy sangyo no kenkyu) hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-07-01

Effects extended to industrial areas by new energy development were analyzed by using the industrial relation table. Technological development of new energies can mass-produce energy without being restricted by energy resource availability, and retaining manufacturing facilities can exhibit energy reserve function with security. The technologies may be suitable for local energy supply. In the aspects of industrial policies and people's living, demands on diversification and improvement of the people's living may be responded, levels of scientific technologies may be enhanced, and contribution to improving the industrial structure may be expected. The energy industry includes a large number of related industries and has vast related areas. A large number of technology induced effects can be expected in the course of research and development. A market of huge size may be estimated in the future, by which level elevation of the industrial structure would be supported. Early promotion of the new energy development is an urgent assignment for the 1980's. In order to achieve this goal, it is necessary to promote research and development, proliferation and practical application, for which the physical strength of the present Japan must be utilized to its maximum in making human and fund investments. Expansion and improvement in the industrialization infrastructures are also important, whereas the government's subsidies must be increased, and vitality in the private sector must be incorporated into organized force. (NEDO)

Low temperature industrial waste heat utilization in the area 'Speyer-Ludwigshafen-Frankenthal-Worms'

International Nuclear Information System (INIS)

Nunold, K.; Krebs, A.

1982-01-01

The aim of the study is the elaboration of reliable facts whether and under which conditions low temperature industrial waste heat systems can be economically utilized for heating purposes. The source of the waste heat are power- and industrial plants. In order to obtain reliable results, investigations have been carried out in the area Speyer-Ludwigshafen-Frankenthal and Worms. These investigations showed a number of application possibilities for heat pumps and it became moreover evident that there is a high variaiton of the heat requirement due to social components and the different type of building structures of the consumers. The economic results showed that the application of this heating system can under certain conditions supplement resp. replace other heating systems. (orig.) [de

Addressing Criticisms of Large-Scale Marine Protected Areas

Science.gov (United States)

Ban, Natalie C; Fernandez, Miriam; Friedlander, Alan M; García-Borboroglu, Pablo; Golbuu, Yimnang; Guidetti, Paolo; Harris, Jean M; Hawkins, Julie P; Langlois, Tim; McCauley, Douglas J; Pikitch, Ellen K; Richmond, Robert H; Roberts, Callum M

2018-01-01

Abstract Designated large-scale marine protected areas (LSMPAs, 100,000 or more square kilometers) constitute over two-thirds of the approximately 6.6% of the ocean and approximately 14.5% of the exclusive economic zones within marine protected areas. Although LSMPAs have received support among scientists and conservation bodies for wilderness protection, regional ecological connectivity, and improving resilience to climate change, there are also concerns. We identified 10 common criticisms of LSMPAs along three themes: (1) placement, governance, and management; (2) political expediency; and (3) social–ecological value and cost. Through critical evaluation of scientific evidence, we discuss the value, achievements, challenges, and potential of LSMPAs in these arenas. We conclude that although some criticisms are valid and need addressing, none pertain exclusively to LSMPAs, and many involve challenges ubiquitous in management. We argue that LSMPAs are an important component of a diversified management portfolio that tempers potential losses, hedges against uncertainty, and enhances the probability of achieving sustainably managed oceans. PMID:29731514

Peat wetland as a natural filter of effluents from adjacent industrial areas

OpenAIRE

József DEZSO; Gabriella TÓTH; Dénes LÓCZY

2015-01-01

The main objective of the project is the study of a peat wetland functioning as recipient of effluents from former and present-day industrial activities. The investigation was focused on heavy metal contaminations and their probable mobilization or fixation. The studied peatbog is a typical Eastern European wetland, located in Hungary on the border between medium mountains (Bakony Mountains) and a Neogene basin (the Sárrét, an area under nature conservation). Watercourses and prevailing air c...

Large area nanoimprint by substrate conformal imprint lithography (SCIL)

Science.gov (United States)

Verschuuren, Marc A.; Megens, Mischa; Ni, Yongfeng; van Sprang, Hans; Polman, Albert

2017-06-01

Releasing the potential of advanced material properties by controlled structuring materials on sub-100-nm length scales for applications such as integrated circuits, nano-photonics, (bio-)sensors, lasers, optical security, etc. requires new technology to fabricate nano-patterns on large areas (from cm2 to 200 mm up to display sizes) in a cost-effective manner. Conventional high-end optical lithography such as stepper/scanners is highly capital intensive and not flexible towards substrate types. Nanoimprint has had the potential for over 20 years to bring a cost-effective, flexible method for large area nano-patterning. Over the last 3-4 years, nanoimprint has made great progress towards volume production. The main accelerator has been the switch from rigid- to wafer-scale soft stamps and tool improvements for step and repeat patterning. In this paper, we discuss substrate conformal imprint lithography (SCIL), which combines nanometer resolution, low patterns distortion, and overlay alignment, traditionally reserved for rigid stamps, with the flexibility and robustness of soft stamps. This was made possible by a combination of a new soft stamp material, an inorganic resist, combined with an innovative imprint method. Finally, a volume production solution will be presented, which can pattern up to 60 wafers per hour.

Fast mapping algorithm of lighting spectrum and GPS coordinates for a large area

Science.gov (United States)

Lin, Chih-Wei; Hsu, Ke-Fang; Hwang, Jung-Min

2016-09-01

In this study, we propose a fast rebuild technology for evaluating light quality in large areas. Outdoor light quality, which is measured by illuminance uniformity and the color rendering index, is difficult to conform after improvement. We develop an algorithm for a lighting quality mapping system and coordinates using a micro spectrometer and GPS tracker integrated with a quadcopter or unmanned aerial vehicle. After cruising at a constant altitude, lighting quality data is transmitted and immediately mapped to evaluate the light quality in a large area.

Health effects of environmental pollution in population living near industrial complex areas in Korea.

Science.gov (United States)

Eom, Sang-Yong; Choi, Jonghyuk; Bae, Sanghyuk; Lim, Ji-Ae; Kim, Guen-Bae; Yu, Seung-Do; Kim, Yangho; Lim, Hyun-Sul; Son, Bu-Soon; Paek, Domyung; Kim, Yong-Dae; Kim, Heon; Ha, Mina; Kwon, Ho-Jang

2018-01-01

Several epidemiological studies have reported an association between environmental pollution and various health conditions in individuals residing in industrial complexes. To evaluate the effects of pollution from industrial complex on human health, we performed a pooled analysis of environmental epidemiologic monitoring data for residents living near national industrial complexes in Korea. The respiratory and allergic symptoms and the prevalence of acute and chronic diseases, including cancer, were used as the outcome variables for health effects. Multiple logistic regression analysis was used to analyze the relationship between exposure to pollution from industrial complexes and health conditions. After adjusting for age, sex, smoking status, occupational exposure, level of education, and body mass index, the residents near the industrial complexes were found to have more respiratory symptoms, such as cough (odds ratio [OR], 1.18; 95% confidence interval [CI], 1.06 to 1.31) and sputum production (OR, 1.13; 95% CI, 1.03 to 1.24), and symptoms of atopic dermatitis (OR, 1.10; 95% CI, 1.01 to 1.20). Among residents of the industrial complexes, the prevalence of acute eye disorders was approximately 40% higher (OR, 1.39; 95% CI, 1.04 to 1.84) and the prevalence of lung and uterine cancer was 3.45 times and 1.88 times higher, respectively, than those among residents of the control area. This study showed that residents living in the vicinity of industrial complexes have a high risk of acute and chronic diseases including respiratory and allergic conditions. These results can be used as basic objective data for developing health management measures for individuals residing near industrial complexes.

Health effects of environmental pollution in population living near industrial complex areas in Korea

Directory of Open Access Journals (Sweden)

Sang-Yong Eom

2018-01-01

Full Text Available Several epidemiological studies have reported an association between environmental pollution and various health conditions in individuals residing in industrial complexes. To evaluate the effects of pollution from industrial complex on human health, we performed a pooled analysis of environmental epidemiologic monitoring data for residents living near national industrial complexes in Korea. The respiratory and allergic symptoms and the prevalence of acute and chronic diseases, including cancer, were used as the outcome variables for health effects. Multiple logistic regression analysis was used to analyze the relationship between exposure to pollution from industrial complexes and health conditions. After adjusting for age, sex, smoking status, occupational exposure, level of education, and body mass index, the residents near the industrial complexes were found to have more respiratory symptoms, such as cough (odds ratio [OR], 1.18; 95% confidence interval [CI], 1.06 to 1.31 and sputum production (OR, 1.13; 95% CI, 1.03 to 1.24, and symptoms of atopic dermatitis (OR, 1.10; 95% CI, 1.01 to 1.20. Among residents of the industrial complexes, the prevalence of acute eye disorders was approximately 40% higher (OR, 1.39; 95% CI, 1.04 to 1.84 and the prevalence of lung and uterine cancer was 3.45 times and 1.88 times higher, respectively, than those among residents of the control area. This study showed that residents living in the vicinity of industrial complexes have a high risk of acute and chronic diseases including respiratory and allergic conditions. These results can be used as basic objective data for developing health management measures for individuals residing near industrial complexes.

The use of industrial type control and monitoring components for a large fusion experiment

International Nuclear Information System (INIS)

Hemming, O.N.; Manduchi, G.; Luchetta, A.; Schmidt, V.; Vitturi, S.

1994-01-01

RFX is one of the large nuclear fusion experiments within the framework of the co-ordinated nuclear fusion research programme of the European Community. During the control system design phase in 1986, the increase in power and flexibility of industrial type programmable controllers lead to the decision for a complete physical split of control, monitoring and data acquisition functions according to speed requirements, allowing the exploitation of the relative advantages of both CAMAC and programmable controllers. The 'slow' control and monitoring functions (for about 4000 digital and 200 analog I/O signals with scanning times of similar 1 second) have been implemented using a series of networked industrial PLCs and personal computers. This has allowed us to choose from a wide range of off-the-shelf hardware and software components for the plant interface and to utilize specialized expertise from the industrial field for the application software implementation. The paper gives the expectations and results gained from this design choice and how it has influenced the decisions for the evolution of the system over the next few years with the utilization of new industrial hardware components. Details are also given regarding the system integration (via the Ethernet network) with the VAX-based CAMAC frontend fast control and data-acquisition system. ((orig.))

Trace elements of concern affecting urban agriculture in industrialized areas: A multivariate approach.

Science.gov (United States)

Boente, C; Matanzas, N; García-González, N; Rodríguez-Valdés, E; Gallego, J R

2017-09-01

The urban and peri-urban soils used for agriculture could be contaminated by atmospheric deposition or industrial releases, thus raising concerns about the potential risk to public health. Here we propose a method to evaluate potential soil pollution based on multivariate statistics, geostatistics (kriging), a novel soil pollution index, and bioavailability assessments. This approach was tested in two districts of a highly populated and industrialized city (Gijón, Spain). The soils showed anomalous content of several trace elements, such as As and Pb (up to 80 and 585 mg kg -1 respectively). In addition, factor analyses associated these elements with anthropogenic activity, whereas other elements were attributed to natural sources. Subsequent clustering also facilitated the differentiation between the northern area studied (only limited Pb pollution found) and the southern area (pattern of coal combustion, including simultaneous anomalies of trace elements and benzo(a)pyrene). A normalized soil pollution index (SPI) was calculated by kriging, using only the elements falling above threshold levels; therefore point-source polluted zones in the northern area and diffuse contamination in the south were identified. In addition, in the six mapping units with the highest SPIs of the fifty studied, we observed low bioavailability for most of the elements that surpassed the threshold levels. However, some anomalies of Pb contents and the pollution fingerprint in the central area of the southern grid call for further site-specific studies. On the whole, the combination of a multivariate (geo) statistic approach and a bioavailability assessment allowed us to efficiently identify sources of contamination and potential risks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bend-resistant large mode area fiber with novel segmented cladding

Science.gov (United States)

Ma, Shaoshuo; Ning, Tigang; Pei, Li; Li, Jing; Zheng, Jingjing

2018-01-01

A novel structure of segment cladding fiber (SCF) with characteristics of bend-resistance and large-mode-area (LMA) is proposed. In this new structure, the high refractive index (RI) core is periodically surrounded by high RI fan-segmented claddings. Numerical investigations show that effective single-mode operation of the proposed fiber with mode field area of 700 μm2 can be achieved when the bending radius is 15 cm. Besides, this fiber is insensitive to the bending orientation at the ranging of [-180°, 180°]. The proposed design shows great potential in high power fiber lasers and amplifiers with compact structure.

On industrial application of structural reliability theory

International Nuclear Information System (INIS)

Thoft-Christensen, P.

1998-01-01

In this paper it is shown that modern structural reliability theory is being successfully applied to a number of different industries. This review of papers is in no way complete. In the literature there is a large number of similar applications and also application not touched on in this presentation. There has been some concern among scientists from this area that structural reliability theory is not being used by industry. It is probably correct that structural reliability theory is not being used by industry as much as it should be used. However, the work by the ESReDA Working Group clearly shows the vary wide application of structural reliability theory by many different industries. One must also have in mind that industry often is reluctant to publish data related to safety and reliability. (au)

Diurnal, weekly and seasonal air concentrations of PCDD and PCDF in an industrial area

International Nuclear Information System (INIS)

Benfenati, E.; Mariani, G.; Schiavon, G.; Lodi, M.; Fanelli, R.

1994-01-01

Air samples were collected in an industrial area close to Milan in July and in November, day and night for five days and have been analyzed for PCDD and PCDF. Average summer levels were generally lower than winter levels, and average concentrations were higher by night than by day in both months. (orig.)

Gravure printing of graphene for large-area flexible electronics.

Science.gov (United States)

Secor, Ethan B; Lim, Sooman; Zhang, Heng; Frisbie, C Daniel; Francis, Lorraine F; Hersam, Mark C

2014-07-09

Gravure printing of graphene is demonstrated for the rapid production of conductive patterns on flexible substrates. Development of suitable inks and printing parameters enables the fabrication of patterns with a resolution down to 30 μm. A mild annealing step yields conductive lines with high reliability and uniformity, providing an efficient method for the integration of graphene into large-area printed and flexible electronics. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evaluating Insects as Bioindicators of Heavy Metal Contamination and Accumulation near Industrial Area of Gujrat, Pakistan

OpenAIRE

Azam, Iqra; Afsheen, Sumera; Zia, Ahmed; Javed, Muqaddas; Saeed, Rashid; Sarwar, Muhammad Kaleem; Munir, Bushra

2015-01-01

To study the accumulation and contamination of heavy metals (i.e., Cd, Cr, Cu, Ni, and Zn) in soil, air, and water, few insect species were assayed as ecological indicators. Study area comes under industrial zone of district Gujrat of Punjab, Pakistan. Insects used as bioindicators included a libellulid dragonfly (Crocothemis servilia), an acridid grasshopper (Oxya hyla hyla), and a nymphalid butterfly (Danaus chrysippus) near industrial zone of Gujrat. Accumulation of Cd was highest in insec...

Large-area atmospheric Cherenkov detectors for high-energy gamma-ray astronomy

International Nuclear Information System (INIS)

Ong, R.A.

1996-01-01

This paper describes the development of new ground-based gamma-ray detectors to explore the energy region between 20 and 200 GeV. This region in energy is interesting because it is currently unexplored by any experiment. The proposed detectors use the atmospheric Cherenkov technique, in which Cherenkov radiation produced in the gamma-ray air showers is detected using mirrors and light-sensitive devices. The important feature of the proposed experiments is the use of large mirror collection areas, which should allow for a significant improvement (i.e. reduction) in energy threshold over existing experiments. Large mirror areas are available for relatively low cost at central tower solar power plants, and there are two groups developing gamma-ray experiments using solar heliostat arrays. This paper summarizes the progress in the design of experiments using this novel approach

Large-Area Binary Blazed Grating Coupler between Nanophotonic Waveguide and LED

Directory of Open Access Journals (Sweden)

Hongqiang Li

2014-01-01

Full Text Available A large-area binary blazed grating coupler for the arrayed waveguide grating (AWG demodulation integrated microsystem on silicon-on-insulator (SOI was designed for the first time. Through the coupler, light can be coupled into the SOI waveguide from the InP-based C-band LED for the AWG demodulation integrated microsystem to function. Both the length and width of the grating coupler are 360 μm, as large as the InP-based C-band LED light emitting area in the system. The coupler was designed and optimized based on the finite difference time domain method. When the incident angle of the light source is 0°, the coupling efficiency of the binary blazed grating is 40.92%, and the 3 dB bandwidth is 72 nm at a wavelength of 1550 nm.

Landscape monitoring of post-industrial areas using LiDAR and GIS technology

Directory of Open Access Journals (Sweden)

Wężyk Piotr

2015-06-01

Full Text Available The quarrying industry is changing the local landscape, forming deep open pits and spoil heaps in close proximity to them, especially lignite mines. The impact can include toxic soil material (low pH, heavy metals, oxidations etc. which is the basis for further reclamation and afforestation. Forests that stand on spoil heaps have very different growth conditions because of the relief (slope, aspect, wind and rainfall shadows, supply of solar energy, etc. and type of soil that is deposited. Airborne laser scanning (ALS technology deliver point clouds (XYZ and derivatives as raster height models (DTM, DSM, nDSM=CHM which allow the reception of selected 2D and 3D forest parameters (e.g. height, base of the crown, cover, density, volume, biomass, etc. The automation of ALS point cloud processing and integrating the results into GIS helps forest managers to take appropriate decisions on silvicultural treatments in areas with failed plantations (toxic soil, droughts on south-facing slopes; landslides, etc. or as regular maintenance. The ISOK country-wide project ongoing in Poland will soon deliver ALS point cloud data which can be successfully used for the monitoring and management of many thousands of hectares of destroyed post-industrial areas which according to the law, have to be afforested and transferred back to the State Forest.

An advanced open path atmospheric pollution monitor for large areas

Energy Technology Data Exchange (ETDEWEB)

Taylor, L.; Suhre, D.; Mani, S. [and others

1996-12-31

Over 100 million gallons of radioactive and toxic waste materials generated in weapon materials production are stored in 322 tanks buried within large areas at DOE sites. Toxic vapors occur in the tank headspace due to the solvents used and chemical reactions within the tanks. To prevent flammable or explosive concentration of volatile vapors, the headspace are vented, either manually or automatically, to the atmosphere when the headspace pressure exceeds preset values. Furthermore, 67 of the 177 tanks at the DOE Hanford Site are suspected or are known to be leaking into the ground. These underground storage tanks are grouped into tank farms which contain closely spaced tanks in areas as large as 1 km{sup 2}. The objective of this program is to protect DOE personnel and the public by monitoring the air above these tank farms for toxic air pollutants without the monitor entering the tanks farms, which can be radioactive. A secondary objective is to protect personnel by monitoring the air above buried 50 gallon drums containing moderately low radioactive materials but which could also emit toxic air pollutants.

Large area UV light source with a semiconductor cathode

International Nuclear Information System (INIS)

Salamov, B. G.; Ciftci, Y. Oe.; Colakoglu, K.

2002-01-01

The light emission (LE) in the UV and visible (blue) range generated by a planar gas discharge system (PGDS) with a semiconductor cathode (SC) are studied. New light source offer high-intensity narrow-band emission at various UV and visible wavelengths (330 - 440 nm). Spectra in N 2 is presented, as well as intensity vs pressure curves for the main peaks of the spectrum. The use of source offers several advantages: PGDS can be extremely efficient energy converters transforming and amplifying a relatively low-powered photon flux incident on the receiving surface of the SC into a flux of high-energy particles over extended areas, i.e. electron, ions, photons. Thus, extremely bright UV and visible sources can be built. LE characteristics of the space in the PGDS are complex, depending on the emitting medium and species. By using the IR light to excite the SC of the system, we have shown that the discharge light emission (DLE) of the device with the N 2 in the gap can serve as an efficient source of the UV radiation if gas pressure and electric field are sufficiently high. This is realized due to the effect of the stabilisation of the spatially homogeneous mode of the discharge in a narrow gap with a large emitting area of SC. Special features of DLE render it highly promising for the development of sources with a large area of the emitting surface, high spatial uniformity of UV radiation, and fast dynamics of these devices. This low cost, high power light sources can provide an interesting alternative to conventional UV lamps

Process variations in surface nano geometries manufacture on large area substrates

DEFF Research Database (Denmark)

Calaon, Matteo; Hansen, Hans Nørgaard; Tosello, Guido

2014-01-01

The need of transporting, treating and measuring increasingly smaller biomedical samples has pushed the integration of a far reaching number of nanofeatures over large substrates size in respect to the conventional processes working area windows. Dimensional stability of nano fabrication processe...

Atmospheric depositions around a heavily industrialized area in a seasonally dry tropical environment of India

International Nuclear Information System (INIS)

Singh, Raj Kumar; Agrawal, Madhoolika

2005-01-01

Clear and throughfall bulk depositions were collected in the downwind of a highly industrialized region in Sonbhadra district of India to estimate the influence of anthropogenic activities on chemical composition of depositions. Significant spatial and temporal variations in depositions of cations and anions were observed. Depositions were higher near the thermal power stations and coalmines as compared to distantly situated site. Seasonally summer samples showed maximum cation and anion depositions followed by winter and minimum in rainy season. The mean pH of the depositions indicates that rainfall in the area is alkaline. Among the anions, maximum deposition was recorded for SO 4 2- followed by NO 3 - and minimum for Cl - . Among the cations, Ca 2+ deposition was maximum followed by NH 4 + . Na + , K + and Mg 2+ deposition rates showed more or less similar values. The depositions of cations and anions as well as pH were higher in throughfall than clearfall samples. Results of the present study suggest that atmospheric depositions are strongly modified due to thermal power stations and coal mines in the area. - Atmospheric abundance of cations have neutralized the acidity of depositions around a heavily industrialized area in India

Single-grain Silicon Technology for Large Area X-ray Imaging

NARCIS (Netherlands)

Arslan, A.

2015-01-01

Digital flat panel X-ray imagers are currently using a-Si and poly-Si thin-film-transistors (TFTs). a-Si TFT permits the use of large area substrates, however, due to the amorphous nature, the carrier mobility is very low (<1 cm2/Vs). Poly-Si TFT improves the mobility (~150 cm2/Vs) but due to random

Design of a broadband ultra-large area acoustic cloak based on a fluid medium

Science.gov (United States)

Zhu, Jian; Chen, Tianning; Liang, Qingxuan; Wang, Xiaopeng; Jiang, Ping

2014-10-01

A broadband ultra-large area acoustic cloak based on fluid medium was designed and numerically implemented with homogeneous metamaterials according to the transformation acoustics. In the present work, fluid medium as the body of the inclusion could be tuned by changing the fluid to satisfy the variant acoustic parameters instead of redesign the whole cloak. The effective density and bulk modulus of the composite materials were designed to agree with the parameters calculated from the coordinate transformation methodology by using the effective medium theory. Numerical simulation results showed that the sound propagation and scattering signature could be controlled in the broadband ultra-large area acoustic invisibility cloak, and good cloaking performance has been achieved and physically realized with homogeneous materials. The broadband ultra-large area acoustic cloaking properties have demonstrated great potentials in the promotion of the practical applications of acoustic cloak.

An insulating grid spacer for large-area MICROMEGAS chambers

International Nuclear Information System (INIS)

Bernard, D.; Delagrange, H.; D'Enterria, D.G.; Guay, M.L.M. Le; Martinez, G.; Mora, M.J.; Pichot, P.; Roy, D.; Schutz, Y.; Gandi, A.; Oliveira, R. de

2002-01-01

We present a novel design for large-area gaseous detectors based on the MICROMEGAS technology. This technology incorporates an insulating grid, sandwiched between the micro-mesh and the anode-pad plane, which provides a uniform 200 μm amplification gap. The uniformity of the amplification gap thickness has been verified. The gain performances of the detector are presented and compared to the values obtained with detectors using cylindrical micro spacers. The new design presents several technical and financial advantages

Analysis of PAEs contaminants in water sources for agriculture, industrial and residential areas from local city district

Science.gov (United States)

Chen, Qidan; Chen, Qixian; Wu, Fei; Liao, Jia; Zhao, Xi

2018-02-01

The technology of DEHP and DBP detection by high performance liquid chromatography coupled with ultraviolet detection (HPLC-UV) was developed and applied in analysis of local water sources from agriculture, industrial and residential areas. Under the optimized sample pretreatment and detection conditions, DEHP and DBP were well separated and detected in 4 mins. The detection limit of DBP was 0.002 mg/L and DEHP was 0.006 mg/L, and it meets the Chinese National Standard limitations for drinking water quality. The linear correlation coefficient of DBP and DEHP standard calibration curves was 0.9998 and 0.9995. The linear range of DBP was 0.020 mg/L ∼20.0 mg/L, with the standard deviation of 0.560% ∼5.07%, and the linear range of DEHP was 0.060 mg/L ∼15.0 mg/L, with the standard deviation of 0.546% ∼5.74%. Ten water samples from Jinwan district of Zhuhai in Guangdong province of China were analyzed. However, the PAEs amounts found in the water sources from industrial areas were higher than the agriculture and residential areas, industries grow incredibly fast in the district in recently years and more attention should be paid to the increasing risks of water sources pollution.

High-Temperature-Short-Time Annealing Process for High-Performance Large-Area Perovskite Solar Cells.

Science.gov (United States)

Kim, Minjin; Kim, Gi-Hwan; Oh, Kyoung Suk; Jo, Yimhyun; Yoon, Hyun; Kim, Ka-Hyun; Lee, Heon; Kim, Jin Young; Kim, Dong Suk

2017-06-27

Organic-inorganic hybrid metal halide perovskite solar cells (PSCs) are attracting tremendous research interest due to their high solar-to-electric power conversion efficiency with a high possibility of cost-effective fabrication and certified power conversion efficiency now exceeding 22%. Although many effective methods for their application have been developed over the past decade, their practical transition to large-size devices has been restricted by difficulties in achieving high performance. Here we report on the development of a simple and cost-effective production method with high-temperature and short-time annealing processing to obtain uniform, smooth, and large-size grain domains of perovskite films over large areas. With high-temperature short-time annealing at 400 °C for 4 s, the perovskite film with an average domain size of 1 μm was obtained, which resulted in fast solvent evaporation. Solar cells fabricated using this processing technique had a maximum power conversion efficiency exceeding 20% over a 0.1 cm 2 active area and 18% over a 1 cm 2 active area. We believe our approach will enable the realization of highly efficient large-area PCSs for practical development with a very simple and short-time procedure. This simple method should lead the field toward the fabrication of uniform large-scale perovskite films, which are necessary for the production of high-efficiency solar cells that may also be applicable to several other material systems for more widespread practical deployment.

Bioaccumulation of selected heavy metals and histopathological and hematobiochemical alterations in backyard chickens reared in an industrial area, India.

Science.gov (United States)

Kar, Indrajit; Mukhopadhayay, Sunit Kumar; Patra, Amlan Kumar; Pradhan, Saktipada

2018-02-01

This study was carried out to determine the concentrations of four heavy metals, cadmium (Cd), lead (Pb), copper (Cu), and cobalt (Co), and histopathological lesions in tissues of chickens reared in an industrial area of West Bengal, India. In particular, Mejhia Block was selected as a heavy metal-exposed area and Vatar Block (120 km away from industrially polluted areas) as a reference site. Samples were collected from the backyard chickens in these areas. Concentrations of heavy metals in soil, water, feedstuffs, tissues (liver, kidney, spleen, lung, and muscle), and droppings were greater (p  kidney > lung > spleen > muscle. Heavy metal concentrations were greater in older chickens (> 1 year) than in young chickens (heavy metal exposure. Histological changes revealed necrotic lesions and tubulitis in the kidney, degeneration and necrosis in liver parenchyma, and periarteriolitis, peribronchiolitis, and presence of hemosiderin pigment in the lung of chickens in the exposed site. Results indicated that backyard chickens in heavy metal-exposed site may show pathological lesions in different tissues due to accumulation of heavy metals, and thus, the consumption of chicken meat from the industrially exposed site may pose a potential health risk to local residents of polluted sites.

Land transportation model for supply chain manufacturing industries

Science.gov (United States)

Kurniawan, Fajar

2017-12-01

Supply chain is a system that integrates production, inventory, distribution and information processes for increasing productivity and minimize costs. Transportation is an important part of the supply chain system, especially for supporting the material distribution process, work in process products and final products. In fact, Jakarta as the distribution center of manufacturing industries for the industrial area. Transportation system has a large influences on the implementation of supply chain process efficiency. The main problem faced in Jakarta is traffic jam that will affect on the time of distribution. Based on the system dynamic model, there are several scenarios that can provide solutions to minimize timing of distribution that will effect on the cost such as the construction of ports approaching industrial areas other than Tanjung Priok, widening road facilities, development of railways system, and the development of distribution center.

In the Shadow of Coal: How Large-Scale Industries Contributed to Present-Day Regional Differences in Personality and Well-Being.

Science.gov (United States)

Obschonka, Martin; Stuetzer, Michael; Rentfrow, Peter J; Shaw-Taylor, Leigh; Satchell, Max; Silbereisen, Rainer K; Potter, Jeff; Gosling, Samuel D

2017-11-20

Recent research has identified regional variation of personality traits within countries but we know little about the underlying drivers of this variation. We propose that the Industrial Revolution, as a key era in the history of industrialized nations, has led to a persistent clustering of well-being outcomes and personality traits associated with psychological adversity via processes of selective migration and socialization. Analyzing data from England and Wales, we examine relationships between the historical employment share in large-scale coal-based industries (coal mining and steam-powered manufacturing industries that used this coal as fuel for their steam engines) and today's regional variation in personality and well-being. Even after controlling for possible historical confounds (historical energy supply, education, wealth, geology, climate, population density), we find that the historical local dominance of large-scale coal-based industries predicts today's markers of psychological adversity (lower Conscientiousness [and order facet scores], higher Neuroticism [and anxiety and depression facet scores], lower activity [an Extraversion facet], and lower life satisfaction and life expectancy). An instrumental variable analysis, using the historical location of coalfields, supports the causal assumption behind these effects (with the exception of life satisfaction). Further analyses focusing on mechanisms hint at the roles of selective migration and persisting economic hardship. Finally, a robustness check in the U.S. replicates the effect of the historical concentration of large-scale industries on today's levels of psychological adversity. Taken together, the results show how today's regional patterns of personality and well-being (which shape the future trajectories of these regions) may have their roots in major societal changes underway decades or centuries earlier. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Large-area cold-cathode grid-controlled electron gun for Antares

International Nuclear Information System (INIS)

Scarlett, W.R.; Andrews, K.; Jansen, J.

1979-01-01

The CO 2 laser amplifiers used in the Antares inertial confinement fusion project require large-area radial beams of high-energy electrons to ionize the laser medium before the main discharge pulse is applied. We have designed a grid-controlled, cold-cathode electron gun with a cylindrical anode having a window area of 9.3 m 2 . A full diameter, 1/4 length prototype of the Antares gun has been built and tested. The design details of the Antares electron gun will be presented as well as test results from the prototype. Techniques used for the prevention and control of emission and breakdown from the grid will also be discussed

The large-scale process of microbial carbonate precipitation for nickel remediation from an industrial soil.

Science.gov (United States)

Zhu, Xuejiao; Li, Weila; Zhan, Lu; Huang, Minsheng; Zhang, Qiuzhuo; Achal, Varenyam

2016-12-01

Microbial carbonate precipitation is known as an efficient process for the remediation of heavy metals from contaminated soils. In the present study, a urease positive bacterial isolate, identified as Bacillus cereus NS4 through 16S rDNA sequencing, was utilized on a large scale to remove nickel from industrial soil contaminated by the battery industry. The soil was highly contaminated with an initial total nickel concentration of approximately 900 mg kg -1 . The soluble-exchangeable fraction was reduced to 38 mg kg -1 after treatment. The primary objective of metal stabilization was achieved by reducing the bioavailability through immobilizing the nickel in the urease-driven carbonate precipitation. The nickel removal in the soils contributed to the transformation of nickel from mobile species into stable biominerals identified as calcite, vaterite, aragonite and nickelous carbonate when analyzed under XRD. It was proven that during precipitation of calcite, Ni 2+ with an ion radius close to Ca 2+ was incorporated into the CaCO 3 crystal. The biominerals were also characterized by using SEM-EDS to observe the crystal shape and Raman-FTIR spectroscopy to predict responsible bonding during bioremediation with respect to Ni immobilization. The electronic structure and chemical-state information of the detected elements during MICP bioremediation process was studied by XPS. This is the first study in which microbial carbonate precipitation was used for the large-scale remediation of metal-contaminated industrial soil. Copyright © 2016 Elsevier Ltd. All rights reserved.

Risk Mapping Case Study: Industrial Area Of Trinec Town (Czech Republic) potentially endangered by floods and landslides

Science.gov (United States)

Dobes, P.; Hrdina, P.; Kotatko, A.; Danihelka, P.; Bednarik, M.; Krejci, O.; Kasperakova, D.

2009-04-01

One of present questions in the context of natural and technological risk mapping, which become important in last years, is analysis and assessment of selected types of multirisks. It results from relevant R&D projetcs and also from international workshops and conferences. From various surveys and presented activities it is evident existence a lot of data and methodological approaches for single risk categories but a lack of tested methodological approaches for multirisks. Within framework of workgroup was done literature search of multirisk assessment methodologies and innovations. The idea of this relatively small, local scale case study arose during the 3rd Risk Mapping Workshop, coordinated by EC DG JRC, IPSC in November 2007. The proposal was based on the previous risk analysis and assessment project, which has been done for Frydek-Mistek County area (Czech Republic) in the year 2002. Several industrial facilities in the Trinec are partly situated in the inundation area of river Olše and are partly protected by concrete barriers built on the banks of Olše. It has to be mentioned that these banks are unstable and in the permanent slow movement. If iron-concrete barriers will be overflowed by water as the result of sudden bank landslide or flood wave, it could trigger several industrial accidents on steel and energy production facilities. Area is highly developed from demographic and socioeconomic point of view. Selected area is in high stage of geological, engineering geological and hydrogeological investigation. Most important scenarios of acidents in the area were developed by What-If analysis and Black box analysis (just growth of several different scenarios; qualitative analysis). In the period of few years later, more QRA analyses of industrial risks were proceeded separately, thanks to District Office, public and Seveso II Directive requirements. General scenarios of multi-hazard events was considered. In the case study, three methodologies was applied

[Heavy Metals Pollution in Topsoil from Dagang Industry Area and Its Ecological Risk Assessment].

Science.gov (United States)

Zhang, Qian; Chen, Zong-juan; Peng, Chang-sheng; Li, Fa-sheng; Gu, Qing-bao

2015-11-01

Based on previous studies and field investigation of Dagang industry area in Tianjin, a total of 128 topsoil samples were collected, and contents of 10 heavy metals (As, Cd, Cr, Co, Cu, Pb, Ni, V, Zn and Hg) were determined. The geoaccumulation index and geostatistics were applied to examine the degree of contamination and spatial distribution of heavy metals in topsoil. The assessment on ecological risk of heavy metals was carried out using Hakanson's method, and the main resources of the heavy metals were analyzed as well. It was found that As, Cd and Co had the highest proportions exceeding Tianjin background value, which were 100%, 97.66% and 96.88%, respectively; the heavy-metal content increased to some extent comparing with that in 2004, and the pollutions of As and Cd were the worst, and other metals were at moderate pollution level or below. The ecological risks of heavy metals were different in topsoil with different land use types, the farmland soil in the southwest as well as soils adjacent to the industrial land were at relatively high potential ecological risk level, and the integrated ecological risk index reached up to 1 437.37. Analysis of correlation and principal component showed that traffic and transportation as well as agricultural activities might be the main resources of heavy metals in the area, besides, the industrial activities in the region might also affect the accumulation of heavy metals.

Effects of uncertainty in model predictions of individual tree volume on large area volume estimates

Science.gov (United States)

Ronald E. McRoberts; James A. Westfall

2014-01-01

Forest inventory estimates of tree volume for large areas are typically calculated by adding model predictions of volumes for individual trees. However, the uncertainty in the model predictions is generally ignored with the result that the precision of the large area volume estimates is overestimated. The primary study objective was to estimate the effects of model...

Radiological protection principles concerning the release for industrial use of areas contaminated from uranium mining

International Nuclear Information System (INIS)

Anon.

1993-01-01

With regard to uses of contaminated grounds as industrial sites, generally all exposure pathways relevant during stays outdoors have to be evaluated. Assuming conditions as realistic as possible, but sufficiently conservative, the dose estimates reveal that radiation exposure from inhalation of both contaminated dust particles and Rn-decay products is lower by almost one order of magnitude than external radiation exposure. The gamma dose rate above the contaminated areas and the potential input of radioactivity into the ground water therefore are relevant exposure pathways during the use of contaminated grounds as mere industrial sites. (orig./DG) [de

Current target industry analysis: Las Vegas Metropolitan Area

International Nuclear Information System (INIS)

Boyle, M.R.

1988-06-01

This is the second of three reports dealing with the Las Vegas MSA's economic development potential in support of an overall effort to prepare an environmental impact statement for the proposed underground nuclear waste storage facility at Yucca Mountain. The first report provides an assessment of the MSA current business climate for economic growth. This second report draws on that business climate assessment to evaluate the Las Vegas MSA's competitive posture in pursuing business investment in the ''primary'' sector of the economy -- businesses which sell their products or services outside the local marketplace and bring new money back into the area and businesses serving local customers who would otherwise import these products or services from suppliers outside the area. GSO has developed an analytic tool which attempts to model the decision process used by businesses in selecting locations for new or expanded business investment. This computer based model reflects variations in site selection decision making among industries and ownership and management types. The underlying premise of the GSO locational compatibility index (LCI) model is that locational decisions are based more on a process of elimination that on a process of selection. There are many factors, some essential and some desirable, which influence any site selection decision. Multivariate comparative analyses narrow the geographic field to a region, then a group of states, then a state, then a sub-state region, then a community and finally to a specific site. Sometimes these analyses are rational and quantitative. More often, they are at least partially random and intuitive. 2 tabs

MLP based models to predict PM10, O3 concentrations, in Sines industrial area

Science.gov (United States)

Durao, R.; Pereira, M. J.

2012-04-01

Sines is an important Portuguese industrial area located southwest cost of Portugal with important nearby protected natural areas. The main economical activities are related with this industrial area, the deep-water port, petrochemical and thermo-electric industry. Nevertheless, tourism is also an important economic activity especially in summer time with potential to grow. The aim of this study is to develop prediction models of pollutant concentration categories (e.g. low concentration and high concentration) in order to provide early warnings to the competent authorities who are responsible for the air quality management. The knowledge in advanced of pollutant high concentrations occurrence will allow the implementation of mitigation actions and the release of precautionary alerts to population. The regional air quality monitoring network consists in three monitoring stations where a set of pollutants' concentrations are registered on a continuous basis. From this set stands out the tropospheric ozone (O3) and particulate matter (PM10) due to the high concentrations occurring in the region and their adverse effects on human health. Moreover, the major industrial plants of the region monitor SO2, NO2 and particles emitted flows at the principal chimneys (point sources), also on a continuous basis,. Therefore Artificial neuronal networks (ANN) were the applied methodology to predict next day pollutant concentrations; due to the ANNs structure they have the ability to capture the non-linear relationships between predictor variables. Hence the first step of this study was to apply multivariate exploratory techniques to select the best predictor variables. The classification trees methodology (CART) was revealed to be the most appropriate in this case.. Results shown that pollutants atmospheric concentrations are mainly dependent on industrial emissions and a complex combination of meteorological factors and the time of the year. In the second step, the Multi

Dynamic of pollutants concentration in forest stands from Copsa Mica industrial area

Directory of Open Access Journals (Sweden)

Marian Ianculescu

2009-12-01

Full Text Available The paper presents the dynamics of pollutants concentrations from nonferrous metallurgical plant in Copsa Mica, considered, between the years 1985 - 1989, as the most polluted area, even in the world, and detected as a large black spot on Landsat satellite imagery. Returning to investigations in this area, after 20-25 years, the pollution activity was changed after 1990, as a consequence of the reduction of industrial capacity, including the black smoke plant decommissioning, and the chimney built for exhaust pollutants over 350 m feet high, resulted some conclusions, necessary for decisions that have to be taken by environmental, forestry, health and agriculture authorities.The litter, soil and vegetation samples were colected from the same permanent sample plots between the years 2006-2009, as between the years 1985-1989, using the same methods, in order to be compared and analyzed. Therefore, returning to investigations in these permanent sample plots, were found the following conclusions: i between the period 1985 - 1989, in all examined cases were revealed high pollutants concentrations, even exceeding the maximum allowable limit (MAL consisting of suphur compounds in synergistic action with heavy metals (Cu, Pb, Cd, Zn, Mn, etc., in vegetation and litter, which was directly correlated with noxious concentrations in the air, and concentrations below MAL in soil samples; ii contrary, regarding the new pollution activity, it has been revealed low noxious concentration, in vegetation, litter and soil samples collected during the period between the years 2006-2008, which are directly related to their low concentration level in the air. Due to pollutants accumulation phenomenon over the years, high pollutants concentrations, ten times higher than MAL, were found in the superior soil layer. In such circumstances the best solution to protect the environment, population and livestock of the damaged area, for tens of thousands of hectares, is the

On industrial application of structural reliability theory

Energy Technology Data Exchange (ETDEWEB)

Thoft-Christensen, P

1998-06-01

In this paper it is shown that modern structural reliability theory is being successfully applied to a number of different industries. This review of papers is in no way complete. In the literature there is a large number of similar applications and also application not touched on in this presentation. There has been some concern among scientists from this area that structural reliability theory is not being used by industry. It is probably correct that structural reliability theory is not being used by industry as much as it should be used. However, the work by the ESReDA Working Group clearly shows the vary wide application of structural reliability theory by many different industries. One must also have in mind that industry often is reluctant to publish data related to safety and reliability. (au) 32 refs.

Large area, low cost solar cell development and production readiness

Science.gov (United States)

Michaels, D.

1982-01-01

A process sequence for a large area ( or = 25 sq. cm) silicon solar cell was investigated. Generic cell choice was guided by the expected electron fluence, by the packing factors of various cell envelope designs onto each panel to provide needed voltage as well as current, by the weight constraints on the system, and by the cost goals of the contract.

Research and chemical industry in 90's

International Nuclear Information System (INIS)

Trapasso, I.

1992-01-01

This paper examines the importance of research with respect to changes taking place within the chemical industry. Specific areas having a significant impact on the future evolution of the industry are identified. The chemical industry is highly R ampersand D intensive with respect to its overall sales volume, as well as, to R ampersand D levels in other industries; and R ampersand D has been a dominant factor influencing the restructuring, on a global scale, of this industry. In the 90's, the industry is expected to have a supply model which is based on the production of marketable high-technology products and integrated systems, developed through coordinated research in multi-disciplinary scientific fields. The optimum strategic and organizational strategies which are to be adopted by the industry during this decade are discussed with reference to the directions being taken by a large multi-national firm in developing strategies in various areas, e.g., new prime materials, environmental protection, pharmacology, and biotechnology. A look is given at recent developments in the sector of advanced polymers, with attention given to processes involving polymer genetics, new products with a wide range of applications and those offering a high level of environmental compatibility. A review of new materials development includes an assessment of prospects for biodegradable plastics based on natural carbohydrates

A large area detector for x-ray applications

International Nuclear Information System (INIS)

Rodricks, B.; Huang, Qiang; Hopf, R.; Wang, Kemei.

1993-01-01

A large area detector for x-ray synchrotron applications has been developed. The front end of this device consist of a scintillator coupled to a fiber-optic taper. The fiber-optic taper is comprised of 4 smaller (70 mm x 70 mm) tapers fused together in a square matrix giving an active area of 140 mm x 140 mm. Each taper has a demagnification of 5.5 resulting in four small ends that are 12 mm diagonally across. The small ends of each taper are coupled to four microchannel-plate-based image intensifiers. The output from each image intensifier is focused onto a Charge Coupled Device (CCD) detector. The four CCDs are read out in parallel and are independently controlled. The image intensifiers also act as fast (20 ns) electronic shutters. The system is capable of displaying images in real time. Additionally, with independent control on the readout of each row of data from the CCD, the system is capable of performing high speed imaging through novel readout manipulation

Academic-industrial partnerships in drug discovery in the age of genomics.

Science.gov (United States)

Harris, Tim; Papadopoulos, Stelios; Goldstein, David B

2015-06-01

Many US FDA-approved drugs have been developed through productive interactions between the biotechnology industry and academia. Technological breakthroughs in genomics, in particular large-scale sequencing of human genomes, is creating new opportunities to understand the biology of disease and to identify high-value targets relevant to a broad range of disorders. However, the scale of the work required to appropriately analyze large genomic and clinical data sets is challenging industry to develop a broader view of what areas of work constitute precompetitive research. Copyright © 2015 Elsevier Ltd. All rights reserved.

Programmable and functional electrothermal bimorph actuators based on large-area anisotropic carbon nanotube paper

Science.gov (United States)

Li, Qingwei; Liu, Changhong; Fan, Shoushan

2018-04-01

Electro-active polymer (EAP) actuators, such as electronic, ionic and electrothermal (ET) actuators, have become an important branch of next-generation soft actuators in bionic robotics. However, most reported EAP actuators could realize only simple movements, being restricted by the small area of flexible electrodes and simple designs. We prepared large-area flexible electrodes of high anisotropy, made of oriented carbon nanotube (CNT) paper, and carried out artful graphic designs and processing on the electrodes to make functional ET bimorph actuators which can realize large bending deformations (over 220°, curvature > 1.5 cm-1) and bionic movements driven by electricity. The anisotropy of CNT paper benefits electrode designs and multiform actuations for complex actuators. Based on the large-area CNT paper, more interesting and functional actuators can be designed and prepared which will have practical applications in the fields of artificial muscles, complicated actuations, and soft and bionic robotics.

An insulating grid spacer for large-area MICROMEGAS chambers

CERN Document Server

Bernard, D; D'Enterria, D G; Le Guay, M; Martínez, G; Mora, M J; Pichot, P; Roy, D; Schutz, Y; Gandi, A; De Oliveira, R

2002-01-01

We present an original design for large area gaseous detectors based on the MICROMEGAS technology. This technology incorporates an insulating grid, sandwiched between the micro-mesh and the anode-pad plane, which provides an uniform 200 $\\mu$m amplification gap. The uniformity of the amplification gap thickness has been verified under several experimental conditions. The gain performances of the detector are presented and compared to the values obtained with detectors using cylindrical micro spacers. The new design presents several technical and financial advantages.

LLNL large-area inductively coupled plasma (ICP) source: Experiments

International Nuclear Information System (INIS)

Richardson, R.A.; Egan, P.O.; Benjamin, R.D.

1995-05-01

We describe initial experiments with a large (76-cm diameter) plasma source chamber to explore the problems associated with large-area inductively coupled plasma (ICP) sources to produce high density plasmas useful for processing 400-mm semiconductor wafers. Our experiments typically use a 640-nun diameter planar ICP coil driven at 13.56 MHz. Plasma and system data are taken in Ar and N 2 over the pressure range 3-50 mtorr. RF inductive power was run up to 2000W, but typically data were taken over the range 100-1000W. Diagnostics include optical emission spectroscopy, Langmuir probes, and B probes as well as electrical circuit measurements. The B and E-M measurements are compared with models based on commercial E-M codes. Initial indications are that uniform plasmas suitable for 400-mm processing are attainable

Digital radiography with large-area flat-panel detectors

International Nuclear Information System (INIS)

Kotter, E.; Langer, M.

2002-01-01

Large-area flat-panel detectors with active readout mechanisms have been on the market for the past 2 years. This article describes different detector technologies. An important distinction is made between detectors with direct and those with indirect conversion of X-rays into electrical charges. Detectors with indirect conversion are built with unstructured or structured scintillators, the latter resulting in less lateral diffusion of emitted light. Some important qualities of flat-panel detectors are discussed. The first phantom and clinical studies published report an image quality at least comparable to that of screen-film systems and a potential for dose reduction. The available studies are summarised in this article. (orig.)

Period doubling and chaos in large area Josephson junctions induced by rf signals

DEFF Research Database (Denmark)

Olsen, O. H.; Samuelsen, Mogens Rugholm

1985-01-01

The influence of an applied rf signal on the emitted radiation from a large area Josephson junction is examined. A model of the system is presented in the framework of the one-dimensional sine-Gordon equation. The model linearizes for small and large values of the amplitude of the applied signal...

Methods for Finding Legacy Wells in Large Areas

Energy Technology Data Exchange (ETDEWEB)

Hammack, Richard W. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Veloski, Garret A. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Hodges, D. Greg [Fugro Airborne Surveys, Mississauga, ON (Canada); White, Jr., Curt M. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States)

2016-06-16

United States. When abandoned, many wells were not adequately sealed and now provide a potential conduit for the vertical movement of liquids and gases. Today, groundwater aquifers can be contaminated by surface pollutants flowing down wells or by deep, saline water diffusing upwards. Likewise, natural gas, carbon dioxide (CO2), or radon can travel upwards via these wells to endanger structures or human health on the surface. Recently, the need to find and plug wells has become critical with the advent of carbon dioxide injection into geologic formations for enhanced oil recovery (EOR) or carbon storage. The potential for natural gas or brine leakage through existing wells has also been raised as a concern in regions where shale resources are hydraulically fractured for hydrocarbon recovery. In this study, the National Energy Technology Laboratory (NETL) updated existing, effective well finding techniques to be able to survey large areas quickly using helicopter or ground-vehicle-mounted magnetometers, combined with mobile methane detection. For this study, magnetic data were collected using airborne and ground vehicles equipped with two boom-mounted magnetometers, or on foot using a hand-held magnetometer with a single sensor. Data processing techniques were employed to accentuate well-casing-type magnetic signatures. To locate wells with no magnetic signature (wells where the steel well casing had been removed), the team monitored for anomalous concentrations of methane, which could indicate migration of volatile compounds from deeper sedimentary strata along a well or fracture pathway. Methane measurements were obtained using the ALPIS DIfferential Absorption Lidar (DIAL) sensor for helicopter surveys and the Apogee leak detection system (LDS) for ground surveys. These methods were evaluated at a 100-year-old oilfield in Wyoming, where a helicopter magnetic survey accurately located 93% of visible wells. In addition, 20% of the wells found by the survey were

Methods for Finding Legacy Wells in Large Areas

Energy Technology Data Exchange (ETDEWEB)

Hammack, Richard [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Veloski, Garret [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States); Hodges, D. Greg [Fugro Airborne Surveys, Mississauga, ON (Canada); White, Jr., Charles E. [National Energy Technology Lab. (NETL), Pittsburgh, PA, (United States)

2016-06-16

More than 10 million wells have been drilled during 150 years of oil and gas production in the United States. When abandoned, many wells were not adequately sealed and now provide a potential conduit for the vertical movement of liquids and gases. Today, groundwater aquifers can be contaminated by surface pollutants flowing down wells or by deep, saline water diffusing upwards. Likewise, natural gas, carbon dioxide (CO₂), or radon can travel upwards via these wells to endanger structures or human health on the surface. Recently, the need to find and plug wells has become critical with the advent of carbon dioxide injection into geologic formations for enhanced oil recovery (EOR) or carbon storage. The potential for natural gas or brine leakage through existing wells has also been raised as a concern in regions where shale resources are hydraulically fractured for hydrocarbon recovery. In this study, the National Energy Technology Laboratory (NETL) updated existing, effective well finding techniques to be able to survey large areas quickly using helicopter or ground-vehicle-mounted magnetometers, combined with mobile methane detection. For this study, magnetic data were collected using airborne and ground vehicles equipped with two boom-mounted magnetometers, or on foot using a hand-held magnetometer with a single sensor. Data processing techniques were employed to accentuate well-casing-type magnetic signatures. To locate wells with no magnetic signature (wells where the steel well casing had been removed), the team monitored for anomalous concentrations of methane, which could indicate migration of volatile compounds from deeper sedimentary strata along a well or fracture pathway. Methane measurements were obtained using the ALPIS DIfferential Absorption Lidar (DIAL) sensor for helicopter surveys and the Apogee leak detection system (LDS) for ground surveys. These methods were evaluated at a 100-year-old oilfield in Wyoming, where a helicopter magnetic

Aerial radiation survey techniques for efficient characterization of large areas

International Nuclear Information System (INIS)

Sydelko, T.; Riedhauser, S.

2006-01-01

Full text: Accidental or intentional releases of radioactive isotopes over potentially very large surface areas can pose serious health risks to humans and ecological receptors. Timely and appropriate responses to these releases depend upon rapid and accurate characterization of impacted areas. These characterization efforts can be adversely impacted by heavy vegetation, rugged terrain, urban environments, and the presence of unknown levels of radioactivity. Aerial survey techniques have proven highly successful in measuring gamma emissions from radiological contaminates of concern quickly, efficiently, and safely. Examples of accidental releases include the unintentional distribution of uranium mining ores during transportation, the loss of uranium processing and waste materials, unintentional nuclear power plant emissions into the atmosphere, and the distribution of isotopes during major flooding events such as the one recently occurring in New Orleans. Intentional releases have occurred during the use of deleted uranium ammunition test firing and war time use by military organizations. The threat of radiological dispersion device (dirty bomb) use by terrorists is currently a major concern of many major cities worldwide. The U.S. Department of Energy, in cooperation with its Remote Sensing Laboratory and Argonne National Laboratory, has developed a sophisticated aerial measurement system for identifying the locations, types, and quantities of gamma emitting radionuclides over extremely large areas. Helicopter mounted Nal detectors are flown at low altitude and constant speed along parallel paths measuring the full spectrum of gamma activity. Analytical procedures are capable of distinguishing between radiological contamination and changes in natural background emissions. Mapped and tabular results of these accurate, timely and cost effective aerial gamma radiation surveys can be used to assist with emergency response actions, if necessary, and to focus more

A Comparison of Customer Relationships between Large Chain Stores and Small Local Stores in the Fashion Industry

OpenAIRE

Krstevska, Biljana

2017-01-01

This research investigates customer relationships of two distinct store formats (small local stores and large chain stores) in the fashion industry. The aim is to find out if there are differences between the store formats regarding customer relationships. Relationship marketing theory was used to formulate hypotheses. Shoppers of small local stores and large chain stores in Würzburg, Germany, were surveyed to test the hypotheses. Results indicate that customer relationships significantly dif...

Efficient Mid-Infrared Supercontinuum Generation in Tapered Large Mode Area Chalcogenide Photonic Crystal Fibers

DEFF Research Database (Denmark)

Petersen, Christian Rosenberg; Engelsholm, Rasmus Dybbro; Markos, Christos

2017-01-01

Mid-infrared supercontinuum spanning from 1.8-9  μm with an output power of 41.5 mW is demonstrated by pumping tapered large mode area chalcogenide photonic crystal fibers using a 4 μm optical parametric source.......Mid-infrared supercontinuum spanning from 1.8-9  μm with an output power of 41.5 mW is demonstrated by pumping tapered large mode area chalcogenide photonic crystal fibers using a 4 μm optical parametric source....

Controlled elaboration of large-area plasmonic substrates by plasma process

International Nuclear Information System (INIS)

Pugliara, A; Despax, B; Makasheva, K; Bonafos, C; Carles, R

2015-01-01

Elaboration in a controlled way of large-area and efficient plasmonic substrates is achieved by combining sputtering of silver nanoparticles (AgNPs) and plasma polymerization of the embedding dielectric matrix in an axially asymmetric, capacitively coupled RF discharge maintained at low gas pressure. The plasma parameters and deposition conditions were optimized according to the optical response of these substrates. Structural and optical characterizations of the samples confirm the process efficiency. The obtained results indicate that to deposit a single layer of large and closely situated AgNPs, a high injected power and short sputtering times must be privileged. The plasma-elaborated plasmonic substrates appear to be very sensitive to any stimuli that affect their plasmonic response. (paper)

Local to regional scale industrial heavy metal pollution recorded in sediments of large freshwater lakes in central Europe (lakes Geneva and Lucerne) over the last centuries

International Nuclear Information System (INIS)

Thevenon, Florian; Graham, Neil D.; Chiaradia, Massimo; Arpagaus, Philippe; Wildi, Walter; Poté, John

2011-01-01

This research first focuses on the spatial and temporal patterns of heavy metals from contrasting environments (highly polluted to deepwater sites) of Lake Geneva. The mercury (Hg) and lead (Pb) records from two deepwater sites show that the heavy metal variations before the industrial period are primarily linked to natural weathering input of trace elements. By opposition, the discharge of industrial treated wastewaters into Vidy Bay of Lake Geneva during the second part of the 20th century, involved the sedimentation of highly metal-contaminated sediments in the area surrounding the WWTP outlet pipe discharge. Eventually, a new Pb isotope record of sediments from Lake Lucerne identifies the long-term increasing anthropogenic lead pollution after ca. 1500, probably due to the development of metallurgical activities during the High Middle Ages. These data furthermore allows to compare the recent anthropogenic sources of water pollution from three of the largest freshwater lakes of Western Europe (lakes Geneva, Lucerne, and Constance). High increases in Pb and Hg highlight the regional impact of industrial pollution after ca. 1750–1850, and the decrease of metal pollution in the 1980s due to the effects of remediation strategies such as the implementation of wastewater treatment plants (WWTPs). However, at all the studied sites, the recent metal concentrations remain higher than pre-industrial levels. Moreover, the local scale pollution data reveal two highly contaminated sites (> 100 μg Pb/g dry weight sediment) by industrial activities, during the late-19th and early-20th centuries (Lake Lucerne) and during the second part of the 20th century (Vidy Bay of Lake Geneva). Overall, the regional scale pollution history inferred from the three large and deep perialpine lakes points out at the pollution of water systems by heavy metals during the last two centuries due to the discharge of industrial effluents. Highlights: ► Natural sources dominated trace element

X-ray spectrometry with Peltier-cooled large area avalanche photodiodes

International Nuclear Information System (INIS)

Fernandes, L.M.P.; Lopes, J.A.M.; Santos, J.M.F. dos; Conde, C.A.N.

2004-01-01

Performance characteristics of the response of a Peltier-cooled large-area avalanche photodiode are investigated. Detector gain, energy linearity, energy resolution and minimum detectable energy are studied at different operation temperatures. Detector energy resolution and lowest detectable X-ray energy present a strong improvement as the operation temperature is reduced from 25 to 15 deg. C and slower improvements are achieved for temperatures below 10 deg. C

Long period gratings written in large-mode area photonic crystal fiber

DEFF Research Database (Denmark)

Nodop, D.; Linke, S.; Jansen, F.

2008-01-01

We report for the first time, to the best of our knowledge, on the fabrication and characterization of CO2-laser written long-period gratings in a large-mode area photonic crystal fiber with a core diameter of 25 mu m. The gratings have low insertion losses ( 10 d...

Analysis on Dangerous Source of Large Safety Accident in Storage Tank Area

Science.gov (United States)

Wang, Tong; Li, Ying; Xie, Tiansheng; Liu, Yu; Zhu, Xueyuan

2018-01-01

The difference between a large safety accident and a general accident is that the consequences of a large safety accident are particularly serious. To study the tank area which factors directly or indirectly lead to the occurrence of large-sized safety accidents. According to the three kinds of hazard source theory and the consequence cause analysis of the super safety accident, this paper analyzes the dangerous source of the super safety accident in the tank area from four aspects, such as energy source, large-sized safety accident reason, management missing, environmental impact Based on the analysis of three kinds of hazard sources and environmental analysis to derive the main risk factors and the AHP evaluation model is established, and after rigorous and scientific calculation, the weights of the related factors in four kinds of risk factors and each type of risk factors are obtained. The result of analytic hierarchy process shows that management reasons is the most important one, and then the environmental factors and the direct cause and Energy source. It should be noted that although the direct cause is relatively low overall importance, the direct cause of Failure of emergency measures and Failure of prevention and control facilities in greater weight.

Evaluation of water resources around Barapukuria coal mine industrial area, Dinajpur, Bangladesh

Science.gov (United States)

Howladar, M. Farhad; Deb, Pulok Kanti; Muzemder, A. T. M. Shahidul Huqe; Ahmed, Mushfique

2014-09-01

Water is a very important natural resource which can be utilized in renewable or non-renewable forms but before utilizing, the evaluation of the quality of this resource is crucial for a particular use. However, the problems of water quality are more severe in areas where the mining and mineral processes' industries are present. In mining processes, several classes of wastes are produced which may turn into ultimately the sources of water quality and environmental degradation. In consequences, the evaluations of water quality for livestock, drinking, irrigation purposes and environmental implications have been carried out around the Barapukuria Coal Mining Industry under different methods and techniques such as primarily the field investigation; secondly the laboratory chemical analysis and thirdly justified the suitability of the laboratory analysis with statistical representation and correlation matrix, Schoeller plot, Piper's Trilinear diagram, Expanded Durov diagram, Wilcox diagram, US salinity diagram, Doneen's chart and others. The results of all surface and ground water samples analysis show that the characteristics and concentrations of all the major physical and chemical parameters such as pH, EC, TDS, Na+, K+, Ca2+, Mg2+, Fetotal, Cl-, HCO3 -, CO3 2- and SO4 2- are varied from one sample to other but well analogous with the WHO and EQS standard limit for all purposes in the area where the abundance of the major ions is as follows: Ca2+ > Na+ > Mg2+ > K+ > Fetotal = HCO3 - > SO4 2- > Cl- > CO3 2-. The graphical exposition of analytical data demonstrates two major hydrochemical facies for example: calcium-bicarbonate (Ca2+- HCO3 -) and magnesium-bicarbonate (Mg2+- HCO3 -) type facies which directly support the shallow recently recharged alkaline water around the industry. The calculated values for the evaluation classification of water based on TDS, Na%, EC, SAR, PI, RSC, MH, and TH replicate good to excellent use of water for livestock, drinking and

Calibration of atomic trajectories in a large-area dual-atom-interferometer gyroscope

Science.gov (United States)

Yao, Zhan-Wei; Lu, Si-Bin; Li, Run-Bing; Luo, Jun; Wang, Jin; Zhan, Ming-Sheng

2018-01-01

We propose and demonstrate a method for calibrating atomic trajectories in a large-area dual-atom-interferometer gyroscope. The atom trajectories are monitored by modulating and delaying the Raman transition, and they are precisely calibrated by controlling the laser orientation and the bias magnetic field. To improve the immunity to the gravity effect and the common phase noise, the symmetry and the overlap of two large-area atomic interference loops are optimized by calibrating the atomic trajectories and by aligning the Raman-laser orientations. The dual-atom-interferometer gyroscope is applied in the measurement of the Earth's rotation. The sensitivity is 1.2 ×10-6 rad s -1 Hz-1/2, and the long-term stability is 6.2 ×10-8 rad/s at 2000 s.

Problems of protection of urban ambient air pollution from industrial dust emissions

Directory of Open Access Journals (Sweden)

Azarov Valeriy

2017-01-01

Full Text Available The development of large cities accompanied by the development of the industry hashistorically led to the fact that now residential areas are located side by side with the industrial production. For instance, exactly this situation has developed in the city of Volgograd, as well as in other Russian cities, where sometimes the distance from large enterprises to a living area is 100 m or less. In addition, small-scale entrepreneurs usually place their production directly in their past places of residence. As a result, the content of harmful substances in the air of city blocks is much higher than the standards of hygiene require. It is obvious that the current situation can be improved through the use of modern, more advanced technologies. However, increasing the efficiency of air systems to protect the city from pollution and industrial emissions is an urgent task. The authors propose a version of the system layout, designed to reduce dust emissions in urban air.

Highly Flexible and High-Performance Complementary Inverters of Large-Area Transition Metal Dichalcogenide Monolayers

KAUST Repository

Pu, Jiang; Funahashi, Kazuma; Chen, Chang-Hsiao; Li, Ming-yang; Li, Lain-Jong; Takenobu, Taishi

2016-01-01

Complementary inverters constructed from large-area monolayers of WSe2 and MoS2 achieve excellent logic swings and yield an extremely high gain, large total noise margin, low power consumption, and good switching speed. Moreover, the WSe2

55-68 Impact of Area Enclosures on Density and Diversity of Large ...

African Journals Online (AJOL)

1Department of Land Resources Management and Environmental Protection, Mekelle University, ... The enclosures have higher density and diversity of large wild mammals ..... in it. Figure 4 Human interference in enclosures of the study area ...

Background simulations for the Large Area Detector onboard LOFT

DEFF Research Database (Denmark)

Campana, Riccardo; Feroci, Marco; Ettore, Del Monte

2013-01-01

and magnetic fields around compact objects and in supranuclear density conditions. Having an effective area of similar to 10 m(2) at 8 keV, LOFT will be able to measure with high sensitivity very fast variability in the X-ray fluxes and spectra. A good knowledge of the in-orbit background environment...... is essential to assess the scientific performance of the mission and optimize the design of its main instrument, the Large Area Detector (LAD). In this paper the results of an extensive Geant-4 simulation of the instrumentwillbe discussed, showing the main contributions to the background and the design...... an anticipated modulation of the background rate as small as 10 % over the orbital timescale. The intrinsic photonic origin of the largest background component also allows for an efficient modelling, supported by an in-flight active monitoring, allowing to predict systematic residuals significantly better than...

Curbing variations in packaging process through Six Sigma way in a large-scale food-processing industry

Science.gov (United States)

Desai, Darshak A.; Kotadiya, Parth; Makwana, Nikheel; Patel, Sonalinkumar

2015-03-01

Indian industries need overall operational excellence for sustainable profitability and growth in the present age of global competitiveness. Among different quality and productivity improvement techniques, Six Sigma has emerged as one of the most effective breakthrough improvement strategies. Though Indian industries are exploring this improvement methodology to their advantage and reaping the benefits, not much has been presented and published regarding experience of Six Sigma in the food-processing industries. This paper is an effort to exemplify the application of Six Sigma quality improvement drive to one of the large-scale food-processing sectors in India. The paper discusses the phase wiz implementation of define, measure, analyze, improve, and control (DMAIC) on one of the chronic problems, variations in the weight of milk powder pouch. The paper wraps up with the improvements achieved and projected bottom-line gain to the unit by application of Six Sigma methodology.

Possibilities in concrete industry towards circular economy through industrial symbiosis

Directory of Open Access Journals (Sweden)

Bjegović Dubravka

2014-01-01

Full Text Available Major challenges of traditional linear concrete industry are utilisation of large amount of non-renewable resources and significant air emissions during production, utilisation and demolition of concrete structures. At the same time, concrete industry has a high potential for a positive shift towards more sustainable production and lower ecological footprint. One of the strategies is to use waste materials and byproducts from other industries as valuable raw materials in concrete industry. This loop can be closed only by taking into account properties of a certain waste material and using them for preparation of special purpose concrete products, in which these properties are favourable. Other strategy is designing concrete tailored for certain environment and service life, making it optimised for that specific purpose. The paper presents some of the available waste and recycled materials in Croatia and research focused on their potential application in civil engineering. The possibilities of utilisation are first explored in laboratory conditions, with the results presented in this paper as an outcome. Based on the obtained results some of the potential areas of application are proposed, in which concrete prepared with these waste materials becomes alternative to classical concrete. Both original scientific research results are presented, but also prototype of products produced based on the scientific research.

Temporal characteristics of black carbon concentrations and its potential emission sources in a southern Taiwan industrial urban area.

Science.gov (United States)

Cheng, Yu-Hsiang; Lin, Chi-Chi; Liu, Jyh-Jian; Hsieh, Cheng-Ju

2014-03-01

This study investigates the temporal characteristics of black carbon and its potential emission sources, as well as the fractions of BC in PM2.5 levels in Kaohsiung urban area, which is an industrial city in southern Taiwan. Concentrations of BC and PM2.5 are monitored continuously from March 2006 to February 2010, using an aethalometer and a tapered element oscillating microbalance monitor. Additionally, the presence of organic compounds (or UV enhanced species) in particles at the sampling site is determined using the Delta-C (UVBC-BC) value. According to long-term measurement results, BC and PM2.5 concentrations are 3.33 and 34.0 μg m(-3), respectively, in the Kaohsiung urban area. The ratio of BC/PM2.5 is approximately 11 %. Low concentration of BC and PM2.5 in the summer of this study period is mostly likely owing to meteorological conditions that favored dispersion of local air pollutants. Nevertheless, BC concentrations peaked markedly during morning hours (7:00-11:00), likely owing to local traffic congestion. Measurement results suggest that BC is released from local traffic activities and emitted from industrial activities at this sampling site. Additionally, Delta-C values are significantly higher than zero during January-March and November-December periods in this industrial urban area, implying that UV enhanced species can be observed. At this sampling site, these UV enhanced species do not only originate from household activity and solid waste burning but also release from industrial activities. The elevated Delta-C values during nighttime (18:00-6:00) in the autumn and winter seasons are likely related to those UV enhanced species in the atmosphere, which can be condensed on particle surface under low temperature conditions. According to long-term measurement results, significantly positive Delta-C values can be observed under temperatures industrial parks and a coal-fired power plant.

2π proportional counting chamber for large-area-coated β sources

Indian Academy of Sciences (India)

Home; Journals; Pramana – Journal of Physics; Volume 86; Issue 6. 2 π proportional counting chamber for large-area-coated β sources ... A provision is made for change ofthe source and immediate measurement of source activity. These sources are used to calibrate the efficiency of contamination monitors at radiological ...

Large area, label-free imaging of extracellular matrix using telecentricity

Science.gov (United States)

Visbal Onufrak, Michelle A.; Konger, Raymond L.; Kim, Young L.

2017-02-01

Subtle alterations in stromal tissue structures and organizations within the extracellular matrix (ECM) have been observed in several types of tissue abnormalities, including early skin cancer and wounds. Current microscopic imaging methods often lack the ability to accurately determine the extent of malignancy over a large area, due to their limited field of view. In this research we focus on the development of simple mesoscopic (i.e. between microscopic and macroscopic) biomedical imaging device for non-invasive assessment of ECM alterations over a large, heterogeneous area. In our technology development, a telecentric lens, commonly used in machine vision systems but rarely used in biomedical imaging, serves as a key platform to visualize alterations in tissue microenvironments in a label-free manner over a clinically relevant area. In general, telecentric imaging represents a simple, alternative method for reducing unwanted scattering or diffuse light caused by the highly anisotropic scattering properties of biological tissue. In particular, under telecentric imaging the light intensity backscattered from biological tissue is mainly sensitive to the scattering anisotropy factor, possibly associated with the ECM. We demonstrate the inherent advantages of combining telecentric lens systems with hyperspectral imaging for providing optical information of tissue scattering in biological tissue of murine models, as well as light absorption of hemoglobin in blood vessel tissue phantoms. Thus, we envision that telecentric imaging could potentially serve for simple site-specific, tissue-based assessment of stromal alterations over a clinically relevant field of view in a label-free manner, for studying diseases associated with disruption of homeostasis in ECM.

Nitrogen large area proportional counter with gas regeneration

International Nuclear Information System (INIS)

Leidner, L.; Sadri, E.

1984-10-01

A nitrogen large area proportional chamber with gas regeneration is introduced to measure alpha and beta/gamma activites. In contrast to the flow counters used till now the new detector is independent of an external gas supply. The gas amplification factor of nitrogen keeps constant up to an impurity of 2% of O 2 . Oxygen diffusing through unavoidable leakages into the counting gas is removed by an activated catalyzer using low temperature copper oxidation. Humidty is adsorbed by a molecular sieve. The closed counter consists of three components: the actual detector, a gas purification cartridge and a gas circulating pump. Finally, the report describes long run experiments being carried out with prototypes. (orig./HP) [de

Productivity and efficiency of economic activity of the Lower Silesia's large area farms in comparison with other large area farms in Poland

Directory of Open Access Journals (Sweden)

Stanisław Minta

2009-01-01

Full Text Available The paper shows economical and financial situation of the agricultural companies which have most of the grounds in lease. Analysed objects were settled on Lower Silesia (the province in the south – west Poland. The main part of the results of research was about productivity and efficiency of economic resources in these objects. The research was made in years 2000-2002. The results of research in analyzed Lower Silesia’s companies were compared with the best Polish large area farms in order of law and organisation forms: leased farms, private farms and partnerships of Polish public agency AWRSP.

Large-area landslide susceptibility with optimized slope-units

Science.gov (United States)

Alvioli, Massimiliano; Marchesini, Ivan; Reichenbach, Paola; Rossi, Mauro; Ardizzone, Francesca; Fiorucci, Federica; Guzzetti, Fausto

2017-04-01

A Slope-Unit (SU) is a type of morphological terrain unit bounded by drainage and divide lines that maximize the within-unit homogeneity and the between-unit heterogeneity across distinct physical and geographical boundaries [1]. Compared to other terrain subdivisions, SU are morphological terrain unit well related to the natural (i.e., geological, geomorphological, hydrological) processes that shape and characterize natural slopes. This makes SU easily recognizable in the field or in topographic base maps, and well suited for environmental and geomorphological analysis, in particular for landslide susceptibility (LS) modelling. An optimal subdivision of an area into a set of SU depends on multiple factors: size and complexity of the study area, quality and resolution of the available terrain elevation data, purpose of the terrain subdivision, scale and resolution of the phenomena for which SU are delineated. We use the recently developed r.slopeunits software [2,3] for the automatic, parametric delineation of SU within the open source GRASS GIS based on terrain elevation data and a small number of user-defined parameters. The software provides subdivisions consisting of SU with different shapes and sizes, as a function of the input parameters. In this work, we describe a procedure for the optimal selection of the user parameters through the production of a large number of realizations of the LS model. We tested the software and the optimization procedure in a 2,000 km2 area in Umbria, Central Italy. For LS zonation we adopt a logistic regression model implemented in an well-known software [4,5], using about 50 independent variables. To select the optimal SU partition for LS zonation, we want to define a metric which is able to quantify simultaneously: (i) slope-unit internal homogeneity (ii) slope-unit external heterogeneity (iii) landslide susceptibility model performance. To this end, we define a comprehensive objective function S, as the product of three

Comparison of Multi-Scale Digital Elevation Models for Defining Waterways and Catchments Over Large Areas

Science.gov (United States)

Harris, B.; McDougall, K.; Barry, M.

2012-07-01

Digital Elevation Models (DEMs) allow for the efficient and consistent creation of waterways and catchment boundaries over large areas. Studies of waterway delineation from DEMs are usually undertaken over small or single catchment areas due to the nature of the problems being investigated. Improvements in Geographic Information Systems (GIS) techniques, software, hardware and data allow for analysis of larger data sets and also facilitate a consistent tool for the creation and analysis of waterways over extensive areas. However, rarely are they developed over large regional areas because of the lack of available raw data sets and the amount of work required to create the underlying DEMs. This paper examines definition of waterways and catchments over an area of approximately 25,000 km2 to establish the optimal DEM scale required for waterway delineation over large regional projects. The comparative study analysed multi-scale DEMs over two test areas (Wivenhoe catchment, 543 km2 and a detailed 13 km2 within the Wivenhoe catchment) including various data types, scales, quality, and variable catchment input parameters. Historic and available DEM data was compared to high resolution Lidar based DEMs to assess variations in the formation of stream networks. The results identified that, particularly in areas of high elevation change, DEMs at 20 m cell size created from broad scale 1:25,000 data (combined with more detailed data or manual delineation in flat areas) are adequate for the creation of waterways and catchments at a regional scale.

Techno-economic assessment of novel vanadium redox flow batteries with large-area cells

Science.gov (United States)

Minke, Christine; Kunz, Ulrich; Turek, Thomas

2017-09-01

The vanadium redox flow battery (VRFB) is a promising electrochemical storage system for stationary megawatt-class applications. The currently limited cell area determined by the bipolar plate (BPP) could be enlarged significantly with a novel extruded large-area plate. For the first time a techno-economic assessment of VRFB in a power range of 1 MW-20 MW and energy capacities of up to 160 MWh is presented on the basis of the production cost model of large-area BPP. The economic model is based on the configuration of a 250 kW stack and the overall system including stacks, power electronics, electrolyte and auxiliaries. Final results include a simple function for the calculation of system costs within the above described scope. In addition, the impact of cost reduction potentials for key components (membrane, electrode, BPP, vanadium electrolyte) on stack and system costs is quantified and validated.

Large area atmospheric-pressure plasma jet

Science.gov (United States)

Selwyn, Gary S.; Henins, Ivars; Babayan, Steve E.; Hicks, Robert F.

2001-01-01

Large area atmospheric-pressure plasma jet. A plasma discharge that can be operated at atmospheric pressure and near room temperature using 13.56 MHz rf power is described. Unlike plasma torches, the discharge produces a gas-phase effluent no hotter than 250.degree. C. at an applied power of about 300 W, and shows distinct non-thermal characteristics. In the simplest design, two planar, parallel electrodes are employed to generate a plasma in the volume therebetween. A "jet" of long-lived metastable and reactive species that are capable of rapidly cleaning or etching metals and other materials is generated which extends up to 8 in. beyond the open end of the electrodes. Films and coatings may also be removed by these species. Arcing is prevented in the apparatus by using gas mixtures containing He, which limits ionization, by using high flow velocities, and by properly spacing the rf-powered electrode. Because of the atmospheric pressure operation, there is a negligible density of ions surviving for a sufficiently long distance beyond the active plasma discharge to bombard a workpiece, unlike the situation for low-pressure plasma sources and conventional plasma processing methods.

Appraisal of venomous metals in selected crops and vegetables from industrial areas of the Punjab Province

International Nuclear Information System (INIS)

Husaini, S.N.; Matiullah; Arif, M.

2011-01-01

Due to the inadequate water sources, usually sewerage water and industrial effluents are being use for irrigation of the agricultural land around the industrial areas in Pakistan wherein crops and vegetables are cultivated. As untreated effluents contain heavy elements, toxic metals and organic pollutants that may find its way through food chain to general public and may cause health hazards. It is, therefore, mandatory to assess the toxic metals in such crops and vegetables. In this regard, samples of corn, millet, cabbage, spinach and potato were collected within the vicinity of industrial areas of the Faisalabad and Gujranwala regions. The food samples were analyzed using neutron activation analysis (NAA) technique. The highest concentration values of Arsenic (1.9 ± 0.1 μg/g) and Cobalt (0.85 ± 0.01 μg/g) were found in cabbage whereas Manganese (91.6 ± 0.2 μg/g), Antimony (0.15 ± 0.03 μg/g) and Selenium (1.1 ± 0.1 μg/g) were observed in spinach and Chromium (9.63 ± 1.3 μg/g) was found in millet crop. The observed concentrations of all the toxic and heavy metals in crops and vegetables are higher than those reported in the literature. (author)

A study on PCB, PCDD/PCDF industrial contamination in an urban/agricultural area. Part I - Soil

Energy Technology Data Exchange (ETDEWEB)

Turrio-Baldassarri, L.; Alivernini, S.; Battistelli, C.L. [Istituto Superiore di Sanita, Rome (IT)] (and others)

2004-09-15

The Istituto Superiore di Sanita is involved in a study on the impact of existing and past industrial activities as possible sources of contamination on the surrounding environment. The study will focus on an industrial plant inside Brescia, a city in the north-west of Italy, where, from 1938 to 1984, 150 tons of polychlorinated biphenyls (PCBs) were produced. In 1994, 1996 and 1998 three monitoring programs, preliminary to the construction of a municipal waste incinerator near the industrial plant, were carried out. High PCBs levels in soils were observed, namely 3000-6000 fold higher than the limits (0,001mg/Kg) allowed by the 1999 Italian law, in an agricultural area where several small farms are located; the farmers have been consuming for a long time food, such as milk and meat, produced in their own farms. This study has different aims: confirming and enriching previous data; helping determining the contamination source; measuring the contamination of the animals living in the area or fed with contaminated forage; evaluate the exposure of the farmers as compared to general population. Moreover, this study is interested in studying the PCB and PCDD/PCDF transfer from soils to humans across the food chain.

3D electrical image in area contaminated by hydrocarbons at the Cubatao, Brazil, industrial pole; Imageamento eletrico 3D em area contaminada por hidrocarbonetono no polo industrial de Cubatao - SP, Brasil

Energy Technology Data Exchange (ETDEWEB)

Baessa, Marcus Paulus Martins [Centro de Pesquisas e Desenvolvimento Leopoldo Americo Miguez de Mello, CENPES, Rio de Janeiro, RJ (Brazil)], E-mail: marcus.baessa@petrobras.br; Oliva, Andresa; Kiang, Chang Hung [Universidade Estadual Paulista, UNESP, Rio Claro, SP (Brazil)], E-mails: aoliva@rc.unesp.br, chang@rc.unesp.br

2010-12-15

This work presents the results of geophysical surveys performed over an oil contaminated site in the Polo Industrial de Cubatao - Sao Paulo. The aim is to characterize geoelectrical signatures associated to hydrocarbon presence in order to delimit and calculate the volume of the contaminated area. For this study were used Vertical Electrical Sounding (VES) and 3D Electrical Imaging for characterization of geology and geoelectrical response of the contaminant. The results showed that the hydrocarbon presence is associated to conductive anomalies due to products from biodegradation. The conductive anomalies are disseminated over the area, totalizing 1365.3 m3 volume. This volume, however, corresponds only to the residual phase contaminants, since it was not possible to map free-phase hydrocarbons. (author)

Homeless Students and Academic Achievement: Evidence from a Large Urban Area