WorldWideScience

Sample records for lanthanum hydrolysis praseodymium

  1. Exchange, x-ray and IR spectral behaviour of lanthanum and praseodymium exchanged zeolite X

    International Nuclear Information System (INIS)

    Das, D.; Upreti, M.C.

    1995-01-01

    Exchange behaviour of lanthanum and praseodymium ions in zeolite X involves three steps: preferential exchange, intrazeolitic exchange and irreversible exchange. At room temperature , higher exchange has been observed with La(III) than with Pr(III) which is attributed to the smaller hydrosphere of lanthanum than praseodymium. IR spectra of these zeolites in KBr pellets show a shift in the major Si-O stretching vibration of 972 cm -1 to higher frequencies. Their x-ray diffraction patterns remain unchanged except a large decrease of the line intensities caused by the absorption of x-rays by heavy La(III) and Pr(III) ions. The present study reports the preparation and physicochemical properties of lanthanum and praseodymium exchanged zeolite X. (author). 12 refs., 3 figs., 3 tabs

  2. The europium and praseodymium hydrolysis in a 2M NaCl environment

    International Nuclear Information System (INIS)

    Jimenez R, M.; Lopez G, H.; Solache R, M.; Rojas H, A.

    1998-01-01

    It was studied the europium and praseodymium hydrolysis in a 2M NaCl ion force environment at 303 K, through two methods: this one extraction with dissolvents (lanthanide-water-NaCl-dibenzoylmethane) in presence of a competitive ligand (diglycolic acid) and that one direct potentiometric titration, of soluble species, followed by a computer refining. The values of one or another techniques of the first hydrolysis constants obtained were similar, which demonstrates that the results are reliable. The set of data obtained on the stability constants of hydrolysis products allowed to draw up the distribution diagrams of chemical species, as europium as praseodymium in aqueous environment. (Author)

  3. Synthesis and investigation of saturated vapor pressure of lanthanum, praseodymium and neodymium tris-isopropylcyclopentadienyls

    International Nuclear Information System (INIS)

    Devyatykh, G.G.; Chernyaev, N.P.; Zverev, Yu.B.; Gavrishchuk, E.M.; Runovskaya, I.V.; Krupnova, Eh.F.; Chesnokova, S.G.

    1980-01-01

    Lanthanum, praseodymium and neodymium tris-isopropylcyclopentadienyls are synthesized with corresponding unhydrous chlorides in tetrahydrofuran solution. Saturated vapour pressure of substances obtained is studied in the 150-262 deg C range by the statistic method using a compensation zero-manometer. Vapour pressure of the compounds in question is shown to increase with the growth of the rare earth element number [ru

  4. Separation of lanthanum from nuclear fuel solutions by high performance liquid chromatography

    International Nuclear Information System (INIS)

    Lazar, G. C.; Petre, M.; Androne, G.; Benga, A.

    2016-01-01

    This paper presents the separation of uranium, praseodymium and lanthanum from nuclear fuel solutions by high performance liquid chromatography (HPLC). The aim of this study is to establish a minimum concentration of lanthanum which can be analyzed by high performance liquid chromatography, and also to study the effect of uranium concentration on the separation of praseodymium and lanthanum. Optimum gradient mode was established for mixture standard stoc solutions with uranium in a concentration of 1 mg/ml, praseodymium and lanthanum in a concentration range of 1-5 μg/ml from each element. These conditions were applied for the separation of lanthanum from a nuclear fuel solution in which praseodymium and lanthanum were added in a concentration of 3 μg/ml from each element. The elution behavior of lanthanum as a function of the pH and the concentration of the mobile phase, using a mixture of 1-octanesulfonic acid sodium salt with a-hidroxyisobutiric acid is presented. (authors)

  5. Lanthanum(III) and praseodymium(III) complexes with bidentate and tetradentate Schiff base ligands containing indole ring

    International Nuclear Information System (INIS)

    Rai, Anita; Sengupta, Soumitra Kumar; Pandey, Om Prakash

    2000-01-01

    Complexes of lanthanum(III) and praseodymium(III) with Schiff bases, prepared from isatin with aniline, 4-chloroaniline, 2- bromoaniline, 2-nitroaniline (Hl), ethylenediamine, o- phenylenediamine and 4-methyl-o-phenylenediamine (H 2 L') have been synthesised and their physico-chemical properties investigated using elemental analysis, molar conductivities, magnetic susceptibility measurements and spectral (visible, infrared and 1 H NMR) data. The Schiff bases HL bind in a bidentate manner while schiff bases H 2 L' bind in a tetradentate manner. The probable structures of the complexes are proposed. (author)

  6. Determination of the constants of the solubility product of Ln(OH)3 and the effect of the chloride ions on the lanthanum hydrolysis, praseodymium and lutetium in aqueous solutions of ion force 2 Molar

    International Nuclear Information System (INIS)

    Lopez G, H.D.

    2005-01-01

    The behavior of lanthanum (III), praseodymium (III), and lutetium (III) was studied in 2 M NaClO 4 (aq) and 2 M NaCl (aq) at 303 K and free -CO 2 conditions. Solubility diagrams (p Ln(aq)-pC H ) were obtained by means of a radiochemical method. The pC H borderlines of saturation and unsaturation zones of the solutions and solubility product constants for Ln(OH) 3 were determined from these diagrams. The fitting of the solubility equation to the experimental values of p Ln(aq)-pC H diagrams allowed the calculation of the first hydrolysis and solubility product constants. Independently, the stability constants for the first species of hydrolysis were determined by means of pH titrations, the data were treated with the program SUPERQUAD and fitted to the mean ligand number equation. The stability constants for the species LnCl 2+ were as well calculated in 2M ionic strength and 303 K from the hydrolysis constant values obtained in both perchlorate and chloride media. The values obtained for La, Pr and Lu were: logK ps : 21.11 ± 0.09, 19.81 ± 0.11 and 18.10 ± 0.13 in 2M NaClO 4 ; logK ps : 22.22 ± 0.09, 21.45 ± 0.14 and 18.52 ± 0.29 in 2M NaCl; log β 1 : - 8.64 ± 0.02, - 8.37 ± 0.01 and - 7.95 ± 0.11 in 2M NaClO 4 ; log β 1 / : - 9.02 ± 0.11, - 8.75 ± 0.01 and - 8.12 ± 0.03 in 2M NaCl and the values for log β 1,Cl were - 0.0255, - 0.155 and - 0.758, respectively. (Author)

  7. Determination of the stability constants of lanthanum, praseodymium, europium, erbium and lutetium complexes with chloride ions

    International Nuclear Information System (INIS)

    Fernandez R, E.

    2008-01-01

    The stability constants of La 3+ , Pr 3+ , Eu 3+ , Er 3+ and Lu 3+ chloride complexes were determined in perchloric acid media using a liquid-liquid extraction method. The dinonyl napthalene sulfonic acid in n-heptane was used as extractant. The lanthanide (Ln) concentrations were measured by a radiochemical (Eu and Lu) and a spectrophotometric (La, Pr, and Er) methods. In the last method, xylenol orange was used for the determinations at ph 6. The stability constants of lanthanum, praseodymium, erbium and lutetium chloride complexes were determined in 2, 3 and 4 M ionic strength and europium in 1, 2 and 3 M, at 303 K. The fitting of experimental data to the equations for the calculation of the stability constants, was carry out considering both one chemical species (LnCl 2+ ) or two chemical species (LnCl 2+ and LnCl 2 + ). The Specific Ion Interaction Theory was applied to the values of log β I Ln , Cl and the first stability constants at zero ionic strength were calculated by extrapolation. The same theory could not be applied to the log β I Ln , 2Cl , due to its low abundance and the values determined for the stability constants were similar. The distribution diagrams of the chemical species were obtained using the program MEDUSA and considering log β I Ln , CI , log β I Ln , 2CI values obtained in this work and the hydrolysis constants taken from the literature. The lanthanide chloride complexes are present in solution at specific conditions of ionic strength, concentration and in the absence of hydrolysis. The log β I Ln , Cl data were related to the charge density and the corresponding equations were obtained. These equations could be used to determine the stability constants along the lanthanide series. (Author)

  8. Spectrophotometric determination of the first hydrolysis constant of praseodymium (III)

    International Nuclear Information System (INIS)

    Gonzalez M, R.; Lopez G, H.; Rojas H, A.

    2010-01-01

    The behavior of the trivalent ion praseodymium in 2 M of NaCl at 303 K and in CO 2 free conditions, was studied. Spectrophotometric titrations of the soluble species were used, in order to obtain the value of the first hydrolysis constant of Pr(III). The data obtained were treated with both the program Squad and by a graphic method, respectively. The result obtained using Squad was log*β 1 = -8.94 ± 0.03, while it was log*β 1 = -8.77 ± 0.03, when calculated graphically. These results are similar to the value obtained previously with the potentiometric method. (Author)

  9. Spectrophotometric determination of the first hydrolysis constant of praseodymium (III)

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez M, R.; Lopez G, H. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Rojas H, A., E-mail: hilario.lopez@inin.gob.m [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Departamento de Quimica, Av. San Rafael Atlixco No. 186, Col. Vicentina, 09340 Mexico D. F. (Mexico)

    2010-07-01

    The behavior of the trivalent ion praseodymium in 2 M of NaCl at 303 K and in CO{sub 2} free conditions, was studied. Spectrophotometric titrations of the soluble species were used, in order to obtain the value of the first hydrolysis constant of Pr(III). The data obtained were treated with both the program Squad and by a graphic method, respectively. The result obtained using Squad was log*{beta}{sub 1}= -8.94 {+-} 0.03, while it was log*{beta}{sub 1}= -8.77 {+-} 0.03, when calculated graphically. These results are similar to the value obtained previously with the potentiometric method. (Author)

  10. RM1 Semiempirical Quantum Chemistry: Parameters for Trivalent Lanthanum, Cerium and Praseodymium.

    Directory of Open Access Journals (Sweden)

    José Diogo L Dutra

    Full Text Available The RM1 model for the lanthanides is parameterized for complexes of the trications of lanthanum, cerium, and praseodymium. The semiempirical quantum chemical model core stands for the [Xe]4fn electronic configuration, with n =0,1,2 for La(III, Ce(III, and Pr(III, respectively. In addition, the valence shell is described by three electrons in a set of 5d, 6s, and 6p orbitals. Results indicate that the present model is more accurate than the previous sparkle models, although these are still very good methods provided the ligands only possess oxygen or nitrogen atoms directly coordinated to the lanthanide ion. For all other different types of coordination, the present RM1 model for the lanthanides is much superior and must definitely be used. Overall, the accuracy of the model is of the order of 0.07Å for La(III and Pr(III, and 0.08Å for Ce(III for lanthanide-ligand atom distances which lie mostly around the 2.3Å to 2.6Å interval, implying an error around 3% only.

  11. The europium and praseodymium hydrolysis in a 2M NaCl environment; La hidrolisis del europio y del praseodimio en un medio 2M de NaCl

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez R, M.; Lopez G, H.; Solache R, M.; Rojas H, A. [Instituto Nacional de Investigaciones Nucleares, Departamento de quimica, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1998-07-01

    It was studied the europium and praseodymium hydrolysis in a 2M NaCl ion force environment at 303 K, through two methods: this one extraction with dissolvents (lanthanide-water-NaCl-dibenzoylmethane) in presence of a competitive ligand (diglycolic acid) and that one direct potentiometric titration, of soluble species, followed by a computer refining. The values of one or another techniques of the first hydrolysis constants obtained were similar, which demonstrates that the results are reliable. The set of data obtained on the stability constants of hydrolysis products allowed to draw up the distribution diagrams of chemical species, as europium as praseodymium in aqueous environment. (Author)

  12. Analysis of the X-ray spectra emitted by laser-produced plasma of highly ionized lanthanum and praseodymium in the 8. 4 to 12. 0 A wavelength range

    Energy Technology Data Exchange (ETDEWEB)

    Zigler, A [Racah Inst. of Physics, Hebrew Univ., Jerusalem (Israel); Mandelbaum, P [Racah Inst. of Physics, Hebrew Univ., Jerusalem (Israel); Schwob, J L [Racah Inst. of Physics, Hebrew Univ., Jerusalem (Israel); Mitnik, D [Racah Inst. of Physics, Hebrew Univ., Jerusalem (Israel)

    1994-06-01

    A detailed analysis of the X-ray spectra emitted by laser produced plasma of lanthanum (8.5-12.5 A) and praseodymium (8.4-11.3 A) is given, using ab-initio calculations with the HULLAC relativistic code. Resonance 3d-nf (n 4, 5, 6) and 3p-4s, 4d transitions of the La XXX and Pr XXXII Ni I-like ions and neighbouring ionization states (La XXVIII to La XXXVI, Pr XXX to Pr XXXVI) have been identified. (orig.).

  13. Effect of the chloride ions on the hydrolysis of praseodymium in a 2M ion force media

    International Nuclear Information System (INIS)

    Lopez G, H.; Jimenez R, M.; Solache R, M.; Rojas H, A.

    2004-01-01

    The constants of the product of solubility and the first of hydrolysis were determined of the Praseodymium in media 2M of NaClO 4 and 2M of NaCl, to 303 K and under conditions free of CO 2 . The diagram of solubility was obtained (pPr (ac) - pC H ), by means of a radiochemical method and with it was established the pC H that limit the saturation and non saturation areas; that diagram allowed, also, to calculate the constant of the product of solubility. Also, it was adjusted with the polynomial of solubility equation, that it allowed to determine and to check the values of the constants of the product of solubility and the first of hydrolysis. Independently, it was determined the first constant of hydrolysis of the element, by means of potentiometric titrations whose data were treated with the computer program named SUPERQUAD and with the adjustment of the equation of the average number of bonds. It was also calculates the log constant β Pr,Cl of the specie PrCI 2+ starting from the hydrolysis constants obtained in the perchlorate and chloride media. (Author)

  14. Synthesis, spectral characterization and in vitro antifungal activity of Lanthanum(III) and Praseodymium(III) complexes with Schiff bases derived from 5-substituted-4-amino-5-hydrazino-1,2,4-triazoles and isatin

    International Nuclear Information System (INIS)

    Singh, Shweta; Tripathi, Priti; Pandey, Om P.; Sengupta, Soumitra K.

    2013-01-01

    The new lanthanum(III) and praseodymium(III) complexes of the general formula (LnCl(L)(H 2 O) 2 ) (Ln = La III or Pr III ; H 2 L = Schiff bases derived from 3-substituted-4-amino-5-hydrazino-1,2,4-triazoles and isatin) have been prepared. The complexes have been characterized by elemental analyses, molecular weight by FAB-mass, thermogravimetry, electrical conductance, magnetic moment and spectral (electronic, infrared, far-infrared, 1 H NMR and 13 C NMR) data. The ligands and all prepared complexes were assayed for antifungal (Aspergillus niger and Helminthosporium oryzae) activities. The activities have been correlated with the structures of the complexes. (author)

  15. Determination of the constants of the solubility product of Ln(OH){sub 3} and the effect of the chloride ions on the lanthanum hydrolysis, praseodymium and lutetium in aqueous solutions of ion force 2 Molar; Determinacion de las constantes del producto de solubilidad de Ln(OH){sub 3} y el efecto de los iones cloruro sobre la hidrolisis de lantano, praseodimio y lutecio en soluciones acuosas de fuerza ionica 2 Molar

    Energy Technology Data Exchange (ETDEWEB)

    Lopez G, H.D

    2005-07-01

    The behavior of lanthanum (III), praseodymium (III), and lutetium (III) was studied in 2 M NaClO{sub 4} (aq) and 2 M NaCl (aq) at 303 K and free -CO{sub 2} conditions. Solubility diagrams (p Ln(aq)-pC{sub H}) were obtained by means of a radiochemical method. The pC{sub H} borderlines of saturation and unsaturation zones of the solutions and solubility product constants for Ln(OH){sub 3} were determined from these diagrams. The fitting of the solubility equation to the experimental values of p Ln(aq)-pC{sub H} diagrams allowed the calculation of the first hydrolysis and solubility product constants. Independently, the stability constants for the first species of hydrolysis were determined by means of pH titrations, the data were treated with the program SUPERQUAD and fitted to the mean ligand number equation. The stability constants for the species LnCl{sup 2+} were as well calculated in 2M ionic strength and 303 K from the hydrolysis constant values obtained in both perchlorate and chloride media. The values obtained for La, Pr and Lu were: logK{sub ps}: 21.11 {+-} 0.09, 19.81 {+-} 0.11 and 18.10 {+-} 0.13 in 2M NaClO{sub 4}; logK{sub ps}: 22.22 {+-} 0.09, 21.45 {+-} 0.14 and 18.52 {+-} 0.29 in 2M NaCl; log {beta}{sub 1}: - 8.64 {+-} 0.02, - 8.37 {+-} 0.01 and - 7.95 {+-} 0.11 in 2M NaClO{sub 4}; log {beta}{sub 1}{sup /} : - 9.02 {+-} 0.11, - 8.75 {+-} 0.01 and - 8.12 {+-} 0.03 in 2M NaCl and the values for log {beta}{sub 1,Cl} were - 0.0255, - 0.155 and - 0.758, respectively. (Author)

  16. Hydrophilic block copolymer-directed growth of lanthanum hydroxide nano-particles

    Energy Technology Data Exchange (ETDEWEB)

    Bouyer, F.; Sanson, N.; Gerardin, C. [Laboratoire de Materiaux Catalytiques et Catalyse en Chimie Organique, UMR 5618 CNRS-ENSCM-UM1, FR 1878, Institut Gerhardt, 34 - Montpellier (France); Destarac, M. [Centre de Recherches Rhodia Aubervilliers, 93 - Aubervilliers (France)

    2006-03-15

    Stable hairy lanthanum hydroxide nano-particles were synthesized in water by performing hydrolysis and condensation reactions of lanthanum cations in the presence of double hydrophilic poly-acrylic acid-b-polyacrylamide block copolymers (PAA-b-PAM). In the first step, the addition of asymmetric PAA-b-PAM copolymers (M{sub w,PAA} {<=} M{sub w,PAM}) to lanthanum salt solutions, both at pH = 5.5, induces the formation of monodispersed micellar aggregates, which are predominantly isotropic. The core of the hybrid aggregates is constituted of a lanthanum polyacrylate complex whose formation is due to bidentate coordination bonding between La{sup 3+} and acrylate groups, as shown by ATR-FTIR experiments and pH measurements. The size of the micellar aggregates depends on the molecular weight of the copolymer but is independent of the copolymer to metal ratio in solution. In the second step, the hydrolysis of lanthanum ions is induced by addition of a strong base such as sodium hydroxide. Either flocculated suspensions or stable anisotropic or spherical nano-particles of lanthanum hydrolysis products were obtained depending on the metal complexation ratio [acrylate]/[La]. The variation of that parameter also enables the control of the size of the core-corona nano-particles obtained by lanthanum hydroxylation. The asymmetry degree of the copolymer was shown to influence both the size and the shape of the particles. Elongated particles with a high aspect ratio, up to 10, were obtained with very asymmetric copolymers (M{sub w,PAM}/M{sub w,PAA}{>=}10) while shorter rice grain-like particles were obtained with a less asymmetric copolymer. The asymmetry degree also influences the value of the critical metal complexation degree required to obtain stable colloidal suspensions of polymer-stabilized lanthanum hydroxide. (authors)

  17. X-ray fluorescence analysis of praseodymium oxide/oxalate for rare earth impurities

    International Nuclear Information System (INIS)

    Chandola, L.C.; Mohile, A.N.

    1976-01-01

    A method for the determination of lanthanum, cerium, neodymium and samarium oxides in praseodymium oxide is described. The sample in the oxalate form is mixed with boric acid binder in the weight ratio of 1:1 and pressed into a pellet. The pellet is irradiated by X-rays from a tungsten tube and fluorescent X-rays are dispersed by a LiF (200) crystal in a Philips semiautomatic X-ray fluorescence spectrometer. The intensity of the characteristic X-rays of the impurity elements is measured by a flow proportional counter at selected 20 angles. The minium determination limit is 0.01% for all impurities. (author)

  18. Structural and constitutional studies of some cerium-praseodymium alloys

    International Nuclear Information System (INIS)

    Altunbas, M.; Harris, I.R.

    1980-01-01

    Room temperature X-ray diffraction studies on some powdered Ce-Pr alloys indicate that the face-centred-cubic (fcc) structure extends from 0 to 65% Pr and the double hexagonal (dhcp) structure from 66 to 100% Pr, after a heat treatment of 600 0 C for 2 h and quickly cooling to room temperature. Variations of atomic volume with composition in both ranges indicate that the volume difference between the fcc form of praseodymium and the dhcp form is similar to that observed for α(dhcp) and β(fcc) lanthanum, whereas extrapolation to 100% Ce from the dhcp range gave an atomic volume for the dhcp Ce appreciably in excess of the atomic volume of fcc γ-Ce. This volume expansion is consistent with a slight change of the effective valency of the cerium atoms in the dhcp solid solutions when compared with the γ-Ce but there is uncertainty as to the precise atomic volume of dhcp β-Ce. The DTA studies indicate a narrow liquidus/solidus separation and the electrical resistivity and DTA measurements indicate a regular change with composition in the transition temperature of the high temperature bcc phase. For the dhcp-fcc transition there is a marked variation in the width of the hysteresis loop across the Ce-Pr system which can be correlated with the degree of plastic deformation involved in the transformation. There is a marked increase in the slope of the transition temperature with composition for the Pr-rich alloys and no such transition is observed for the praseodymium samples after one heating cycle. A possible dhcp-fcc transition, however, is indicated by the DTA traces of the commercially pure praseodymium sample on cycling with temperature and this has been attributed to the influence of interstitial impurities. (author)

  19. Determination of the stability constants of lanthanum, praseodymium, europium, erbium and lutetium complexes with chloride ions; Determinacion de las constantes de estabilidad de los complejos de lantano, praseodimio, europio, erbio y lutecio con iones cloruro

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez R, E [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2008-07-01

    The stability constants of La{sup 3+}, Pr{sup 3+}, Eu{sup 3+}, Er{sup 3+} and Lu{sup 3+} chloride complexes were determined in perchloric acid media using a liquid-liquid extraction method. The dinonyl napthalene sulfonic acid in n-heptane was used as extractant. The lanthanide (Ln) concentrations were measured by a radiochemical (Eu and Lu) and a spectrophotometric (La, Pr, and Er) methods. In the last method, xylenol orange was used for the determinations at ph 6. The stability constants of lanthanum, praseodymium, erbium and lutetium chloride complexes were determined in 2, 3 and 4 M ionic strength and europium in 1, 2 and 3 M, at 303 K. The fitting of experimental data to the equations for the calculation of the stability constants, was carry out considering both one chemical species (LnCl{sup 2+}) or two chemical species (LnCl{sup 2+} and LnCl{sub 2}{sup +}). The Specific Ion Interaction Theory was applied to the values of log {beta}{sup I}{sub Ln},{sub Cl} and the first stability constants at zero ionic strength were calculated by extrapolation. The same theory could not be applied to the log {beta}{sup I}{sub Ln},{sub 2Cl}, due to its low abundance and the values determined for the stability constants were similar. The distribution diagrams of the chemical species were obtained using the program MEDUSA and considering log {beta}{sup I}{sub Ln},{sub CI}, log {beta}{sup I}{sub Ln},{sub 2CI} values obtained in this work and the hydrolysis constants taken from the literature. The lanthanide chloride complexes are present in solution at specific conditions of ionic strength, concentration and in the absence of hydrolysis. The log {beta}{sup I}{sub Ln},{sub Cl} data were related to the charge density and the corresponding equations were obtained. These equations could be used to determine the stability constants along the lanthanide series. (Author)

  20. Effect of the chloride ions on the hydrolysis of praseodymium in a 2M ion force media; Efecto de los iones cloruro sobre la hidrolisis del praseodimio en medio de fuerza ionica 2M

    Energy Technology Data Exchange (ETDEWEB)

    Lopez G, H.; Jimenez R, M.; Solache R, M.; Rojas H, A. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2004-07-01

    The constants of the product of solubility and the first of hydrolysis were determined of the Praseodymium in media 2M of NaClO{sub 4} and 2M of NaCl, to 303 K and under conditions free of CO{sub 2}. The diagram of solubility was obtained (pPr{sub (ac)} - pC{sub H}), by means of a radiochemical method and with it was established the pC{sub H} that limit the saturation and non saturation areas; that diagram allowed, also, to calculate the constant of the product of solubility. Also, it was adjusted with the polynomial of solubility equation, that it allowed to determine and to check the values of the constants of the product of solubility and the first of hydrolysis. Independently, it was determined the first constant of hydrolysis of the element, by means of potentiometric titrations whose data were treated with the computer program named SUPERQUAD and with the adjustment of the equation of the average number of bonds. It was also calculates the log constant {beta}{sub Pr,Cl} of the specie PrCI{sup 2+} starting from the hydrolysis constants obtained in the perchlorate and chloride media. (Author)

  1. Synthesis and characterization of praseodymium-142 hydroxyapatite (142Pr-HA)

    International Nuclear Information System (INIS)

    Duyeh Setiawan; Daud Nurhasan

    2015-01-01

    The use of radioisotope of lanthanide group with range of beta energy 0.4 - 2.2 MeV has been renewed interest in nuclear medicine. Praseodymium-142 radioisotope ( 142 Pr, t 1/2 = 19.2 hours, E β = 2.16 MeV) is suitable for applications radiotherapy. Labelled of the hydroxyapatite (Ca 10 (PO 4 )6(OH) 2 ) can be used as carrier of radionuclide after injection in the body injection. This research aim as a preliminary studies to make praseodymium-142 hydroxyapatite ( 142 Pr-HA) as a radiotherapy agent. The optimum condition of praseodymium-142 hydroxyapatite synthesis by controlling several parameters such as the pH and the weight of hydroxyapatite was obtained from process by used the nonradioactive praseodymium. The optimum condition of hydroxyapatite by praseodymium are at pH 5 and weight ratio praseodymium : hydroxyapatite is 1 : 16. The percentage of labeling hydroxyapatite with 142 PrCl 3 was 99.50% and the radiochemical purity of 142 Pr-Ha was 95.20%. (author)

  2. Determination of micro amounts of praseodymium by analogue derivative spectrophotometry

    International Nuclear Information System (INIS)

    Ishii, Hajime; Satoh, Katsuhiko.

    1986-01-01

    Derivative spectrophotometry using the analogue differentiation circuit was applied to the determination of praseodymium at the ppm level. By the proposed method, in which the second or fourth derivative spectrum of the characteristic absorption band of praseodymium(III) at 444 nm is measured, as little as 3 ppm of praseodymium can be determined directly and easily even in the presence of large amounts of other rare earths without any prior separation. Interferences from neodymium, samarium, dysprosium, holmium and erbium ions which have characteristic absorption bands around 444 nm can easily be removed by utilizing the isosbestic point in the derivative spectra of praseodymium(III) and the interfering rare earth(III). (author)

  3. Crystal and molecular structure of praseodymium pivalate adduct with α,α'-dipyridyl

    International Nuclear Information System (INIS)

    Pisarevskij, A.P.; Mitrofanova, R.D.; Frolovskaya, S.N.; Martynenko, L.I.

    1995-01-01

    Synthesis and X-ray diffraction analysis of praseodymium tris-pivalate adduct with α,α'-dipyridyl of PrPiv 3 Dipy composition were conducted. Coordination number of praseodymium atom equals 9 in central-symmetrical dimeric molecule. Praseodymium atoms are connected by two bidentate-bridge and two tridentate-bridge-cyclic carboxylic groups. Molecules of α.α'-Dipy form five-membered chelate cycles. 5 refs., 1 scheme, 1 tab

  4. Luminescent properties of praseodymium in some fluorides

    International Nuclear Information System (INIS)

    Potapov, A.S.; Rodnyj, P.A.; Mikhrin, S.B.; Magunov, I.R.

    2005-01-01

    Influence of diverse factors on efficiency of the Pr 3+ cascade emission in BaF 2 : Pr and SrAlF 5 : Pr. The effect of the environment of the luminescence center on the mutual position of the lowest 5d and the 4f level 1 S 0 of Pr 3+ ion is considered. PrF 3 clustering in BaF 2 is observed at a high praseodymium concentration. The promising potential of magnesium as a charge compensator for praseodymium in SrAlF 5 is demonstrated [ru

  5. Variable valence of praseodymium in rare-earth oxide solid solutions

    International Nuclear Information System (INIS)

    Kravchinskaya, M.V.; Merezhinskii, K.Y.; Tikhonov, P.A.

    1986-01-01

    Solid solutions of elevated praseodymium oxide content have interesting electrical properties, making them the basis for the manufacture of high-temperature electrically conducting materials. Establishment of the composition-structure-valence state relationships enables control of the material properties. The authors performed investigations using a thermogravimetric apparatus with an electronic microbalance of type EM-5-3M, and using x-ray phase analysis of powders (DRON-1 diffractometer, CuK /SUB alpha/ -radiation). The authors also studied the kinetics of praseodymium oxidation with a thermogravimetric apparatus under isothermal conditions. Evaluation of the results with the equation of Kolmogorov, Erofeev, and Avraam indicates that the process is limited by the chemical oxidation of praseodymium and not by diffusion

  6. Spectrophotometric determination of neodymium in mixture with lanthanum by eosin and 2,2'-dipyridyl

    International Nuclear Information System (INIS)

    Ovchar, L.A.; Poluehktov, N.S.

    1980-01-01

    The possibility of using rare earth complexes with eosin (EO) and 2.2-dipyridyl (DP) for spectrophotometric determination of some rare earths in the presence of the others. It has been out that the complexes are not extracted by organic solvents. The PH region of complex existence (approximately 6) and the relation of components in them (rare earths:DP:EO=1:2:3) are determined. The possibility has been shown of determining all the rare earts from praseodymium to lutetium and yttrium in a binary mixture with lanthanum based on different stability of the studied complexes. The method has been tested on the example of determining Nd 2 O 3 in a mixture with La 2 O 3 . The low limit of determined contents is 1-2%. The relative standard deviation is 0.035-0.17 [ru

  7. Magnetic exciton dispersion in praseodymium

    DEFF Research Database (Denmark)

    Rainford, B. D.; Houmann, Jens Christian Gylden

    1971-01-01

    Measurements of the dispersion of magnetic excitons have been made in a single crystal of praseodymium metal using inelastic neutron scattering. A preliminary analysis of the data yields the first detailed information about the exchange interactions and the crystal field splittings in the light...... rare-earth metals....

  8. Hyperfine coupling in gadolinium-praseodymium alloys by specific heat measurements

    International Nuclear Information System (INIS)

    Michel, J.

    1969-01-01

    We have studied the hyperfine coupling in gadolinium-praseodymium alloys by specific heat measurements down to 0.3 K. In the first part we describe the apparatus used to perform our measurements. The second part is devoted to some theoretical considerations. We have studied in detail the case of praseodymium which is an exception in the rare earth series. The third part shows the results we have obtained. (author) [fr

  9. Study in aqueous solution of the praseodymium inclusion in β-cyclodextrin in 2 M of NaCl

    International Nuclear Information System (INIS)

    De la Cruz M, N.

    2013-01-01

    In the fission of uranium to produce electricity, generated between the fission products which are the lanthanides and actinides that at any given time may come into contact with aqueous media, because of this, praseodymium was including in the β-cyclodextrin in order to increase the solubility and stability of praseodymium by forming inclusion complexes Praseodymium-β-cyclodextrin (Pr-β-Cd). The inclusion study was conducted in a proportion of praseodymium and β-cyclodextrin. Infrared spectra, Raman and X-ray diffraction showed the presence of praseodymium and β-cyclodextrin in the inclusion complex, in both proportions. The analysis by scanning electron microscopy confirmed the inclusion of praseodymium in βcyclodextrin. In general, the results of characterization obtained by these techniques show the formation of the inclusion complex. Furthermore, the behaviour of praseodymium inclusion in the β-cyclodextrin was studied in 2 M NaCl at 303 K and free-CO 2 conditions. For this reason, we used two methods: spectrophotometric and potentiometric titration direct of praseodymium-β-cyclodextrin, the data were treated graphically and with the program SUPERQUAD, respectively. The values obtained for praseodymium by spectrophotometric method was: log β 1 = -8.75 calculated graphically and with the potentiometric method, using program SUPERQUAD were logβ 1,OH = -8.73 ± 0.01 logβ 1,2OH = -18.27 ± 0.16 and logβ 1,3OH = -26.44 ± 0.02 obtained simultaneously. (Author)

  10. Extraction spectrophotometric determination of rare earth with trioctylethylammonium bromide and Xylenol Orange

    International Nuclear Information System (INIS)

    Shijo, Yoshio

    1976-01-01

    A spectrophotometric method of determination of the rare earth was studied by the solvent extraction of rare earth-Xylenol Orange chelate into xylene solution of trioctylethylammonium bromide(TOEA). The rare earth-XO-TOEA complexes are extracted into aromatic hydrocarbons such as benzene, toluene, and xylene, but not into polar solvents such as n-butanol ethylacetate, methylisobutylketone, and nitrobenzene. The optimum pH range for the extraction were 6.3 -- 6.7, 6.3 -- 6.5, 5.8 -- 6.9, 5.7 -- 6.9, and 5.5 -- 6.8 for lanthanum, praseodymium, cerium, gadolinium, and dysprosium, respectively. The absorption maximum of the complexes extracted into xylene were found at 605 nm for lanthanum, praseodymium, and cerium, 596 nm for gadolinium, and 590 nm for dysprosium. Beer's law held for about 0 -- 4.5 μg of rare earth per 5 ml of xylene. The molar absorptivity of the extracted species were 1.53x10 5 , 1.42x10 5 , 1.35x10 5 , 8.5x10 4 , 8.2x10 4 cm -1 mol -1 l for lanthanum, praseodymium, cerium, gadolinium, and dysprosium, respectively. The composition of the ternary complexes were estimated to be M:XO:TOEA=1:1:2 for gadolinium and dysprosium, whereas 1:2:n for lanthanum, praseodymium and cerium. Combination ratio n of TOEA to metal-XO chelates in the latters could not be estimated by the commonly available methods. Thorium, vanadium, uranium, bismuth, aluminum, zirconium, chromium, nitrate, perchlorate and iodide interfered when triethylenetetramine and 1,10-phenanthroline were added as masking agent. (auth.)

  11. Calibration curves for quantifying praseodymium by UV-VIS

    International Nuclear Information System (INIS)

    Gonzalez M, R.; Lopez G, H.; Rojas H, A.

    2007-01-01

    The UV-Vis spectroscopic technique was used to determine the absorption bands depending on the concentration from the praseodymium solutions at pH3. Those more appropriate were in the wavelength of 215 nm, for concentrations of 0.0001-0.026 M, of 481nm, 468 nm and 443 nm, for concentrations of 0.026-0.325 M, and of 589 nm, for concentrations of 0.026-0.65 M of the praseodymium. To these wavelengths the calibration curves were determined, which presented correlation coefficients between 0.9976 and 0.9999 except of the absorption of 589 nm that gave R 2 = 0.9014. (Author)

  12. Theoretical study of the magnetic heat capacity of praseodymium metal

    International Nuclear Information System (INIS)

    Glenn, R.L.

    1976-01-01

    The heat capacity of praseodymium metal at low temperatures is calculated using a valence change model. The effect of the presence of a small temperature-dependent and field-dependent percentage of 4+ ions is computed using crystalfield techniques. Good agreement with the experimentally determined values is obtained for polycrystalline and single-crystal praseodymium in zero field and various other fields up to 30 koe. In addition, the effects of selected exchange models on the heat capacity and susceptibility are computed. The model is shown to be compatible with both the parallel and perpendicular susceptibilities

  13. Encephalopathy caused by lanthanum carbonate.

    Science.gov (United States)

    Fraile, Pilar; Cacharro, Luis Maria; Garcia-Cosmes, Pedro; Rosado, Consolacion; Tabernero, Jose Matias

    2011-06-01

    Lanthanum carbonate is a nonaluminum, noncalcium phosphate-binding agent, which is widely used in patients with end-stage chronic kidney disease. Until now, no significant side-effects have been described for the clinical use of lanthanum carbonate, and there are no available clinical data regarding its tissue stores. Here we report the case of a 59-year-old patient who was admitted with confusional syndrome. The patient received 3750 mg of lanthanum carbonate daily. Examinations were carried out, and the etiology of the encephalopathy of the patient could not be singled out. The lanthanum carbonate levels in serum and cerebrospinal fluid were high, and the syndrome eased after the drug was removed. The results of our study confirm that, in our case, the lanthanum carbonate did cross the blood-brain barrier (BBB). Although lanthanum carbonate seems a safe drug with minimal absorption, this work reveals the problem derived from the increase of serum levels of lanthanum carbonate, and the possibility that it may cross the BBB. Further research is required on the possible pathologies that increase serum levels of lanthanum carbonate, as well as the risks and side-effects derived from its absorption.

  14. A Study on the Analysis of Minerals and Materials

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kun-Han; Shim, Sang-Kwon; Lee, Kil-Yong [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

    1999-12-01

    This study is concerned with the analysis of rare earth group elements especially (Lanthanum, Cerium, Praseodymium and Neodymium) in minerals and materials. Rare elements are widely used as electric, electronics, catalysts, optics, materials of super conductors. They are found wide applications in metallurgy and alloy, glass industry. Cerium, the dominant member of often-overlooked lanthanide series, is essential to many industries. Its metallurgical applications alone include use as an alloying agent or as an ingredient in coatings for iron and steel, superalloys, aluminum alloys, aluminum electrowinning, chrome plating and in welding electrodes and lighter flints. Other applications range the gamut from optical coating and radiation detection to fluorescent lighting and chemotherapy. They are found in many items of electronics industry and serve to an increasing extent as a form of investment. Rare earth elements occurs in traces in most minerals and materials. They are extracted in minute quantities from a limited number of ores. They are concentrated and separated from each other by elaborate chemical processes. In this survey, effects of various acid concentration, diverse interfering elements, various decomposition methods were observed for the determination of Lanthanum, Cerium. Praseodymium and Neodymium using standard reference materials by ICP-AES. As the results, for the determination of these elements should be separated form matrix elements by separated concentration method. Also in order to confirm specification of samples, major, minor and trace elements in samples should be analyzed by ICP-AES and XRF. All analytical results of Lanthanum, Cerium, Praseodymium and Neodymium in standard reference sample and real samples compare with the NAA. Finally the relative standard deviations of approximately 1% S are found from the precision study using standard reference sample for Lanthanum, Cerium, Praseodymium and Neodymium. (author). 22 refs., 33 tabs., 10

  15. X-ray Topographic Investigations of Domain Structure in Czochralski Grown PrxLa1-xAlO3 Crystals

    International Nuclear Information System (INIS)

    Wieteska, K.; Wierzchowski, W.; Malinowska, A.; Turczynski, S.; Pawlak, D.A.; Lukasiewicz, T.; Lefeld-Sosnowska, M.; Graeff, W.

    2010-01-01

    In the present paper X-ray diffraction topographic techniques were applied to a number of samples cut from Czochralski grown Pr x La 1-x AlO 3 crystals with different ratio of praseodymium and lanthanum. Conventional and synchrotron X-ray topographic investigations revealed differently developed domain structures dependent on the composition of mixed praseodymium lanthanum aluminium perovskites. Some large mosaic blocks were observed together with the domains. In the best crystals, X-ray topographs revealed striation fringes and individual dislocations inside large domains. Synchrotron topographs allowed us to indicate that the domains correspond to three different crystallographic planes, and to evaluate the lattice misorientation between domains in the range of 20-50 arc min (authors)

  16. The isolation of 139Ce after production by a proton-induced nuclear reaction on praseodymium

    International Nuclear Information System (INIS)

    Van der Walt, T.N.; Vermeulen, C.

    2004-01-01

    A method, based on anion exchange chromatography, is presented for the isolation of 139 Ce after production by a proton-induced nuclear reaction on a thick praseodymium target. After bombardment the target is dissolved in nitric acid and 139 Ce oxidised to the Ce(IV) oxidation state with bromic acid. 139 Ce is then separated form the praseodymium by anion exchange chromatography on a Ag MP-1 resin column in a nitric acid - bromic acid mixture. 139 Ce is sorbed onto the resin column and praseodymium eluted with the acid mixture. The bromic acid is washed out of the column with nitric acid and 139 Ce finally eluted with dilute nitric acid containing sulphur dioxide

  17. Age hardening and creep resistance of cast Al–Cu alloy modified by praseodymium

    International Nuclear Information System (INIS)

    Bai, Zhihao; Qiu, Feng; Wu, Xiaoxue; Liu, Yingying; Jiang, Qichuan

    2013-01-01

    The effects of praseodymium on age hardening behavior and creep resistance of cast Al–Cu alloy were investigated. The results indicated that praseodymium facilitated the formation of the θ′ precipitates during the age process and improved the hardness of the Al–Cu alloy. Besides, praseodymium resulted in the formation of the Al 11 Pr 3 phase in the grain boundaries and among the dendrites of the modified alloy. Because of the good thermal stability of Al 11 Pr 3 phase, it inhibits grain boundary migration and dislocation movement during the creep process, which contributes to the improvement in the creep resistance of the modified alloy at elevated temperatures. - Highlights: • Pr addition enhances the hardness and creep resistance of the Al–Cu alloy. • Pr addition facilitates the formation of the θ′ precipitates. • Pr addition results in the formation of the Al11Pr3 phase in the Al–Cu alloy

  18. Lanthanum additions and the toughness of ultra-high strength steels and the determination of appropriate lanthanum additions

    International Nuclear Information System (INIS)

    Garrison, Warren M.; Maloney, James L.

    2005-01-01

    Studies of commercial heats of AF1410 steel suggest that under appropriate conditions additions of rare-earth elements can significantly enhance fracture toughness. This improvement in toughness is not due to an extremely low inclusion volume fraction but is apparently due to the formation of larger and more widely spaced inclusions. The purpose of this work is to discuss our experience in using rare-earth additions to laboratory scale vacuum induction melted and subsequently vacuum arc remelted heats of ultra-high strength steels to achieve inclusion distributions similar to those observed in commercial heats modified with lanthanum additions. The results indicate that lanthanum additions of 0.015 wt.% to low sulfur steels which have been well deoxidized using carbon-vacuum deoxidation can result in lanthanum rich inclusions which are similar in size, volume fraction and spacing to those obtained in commercially produced heats of ultra-high strength steel to which lanthanum has been added. The heat of steel to which lanthanum additions of 0.015 wt.% were made had significantly higher toughness than did the heat of the same steel in which the sulfur had been gettered as small and closely spaced particles of MnS and which had an inclusion volume fraction similar to that of the heat modified by the addition of 0.015 wt.% lanthanum. This improvement in toughness was attributed to an increase in inclusion spacing. An addition of 0.06 wt.% lanthanum was excessive. Such an addition of lanthanum resulted in a huge volume fraction of large cuboidal inclusions which primarily contain lanthanum and oxygen and which are extremely detrimental to toughness

  19. Synthesis of praseodymium allyl iodide complex and its use in piperilene polymerization

    International Nuclear Information System (INIS)

    Gajlyunas, G.A.; Biktimirov, R.Kh.; Khajrullina, R.M.; Marina, N.G.; Manakov, Yu.B.; Tolstikov, G.A.

    1987-01-01

    Synthesis, structure and catalytic properties of tetrahydrofuran praseodymium allyl iodine complex (1) are described and studied. Complex 1 is formed during interaction of allyl iodine with metal praseodymium (the molar ratio is 2:1) in THF at room temperature with 97% yield. It represents the solid powder-like substance of the light-brown colour with a pale green shade, being sensitive to moisture and oxygen and decomposing at temperature >120 deg. On the basis of the IR-spectroscopy data the supposition about the dimeric (or n-dimensional) complex structure is made. The complex prepared in combination with tributyl aluminium during piperylene polymerization gives a high-stereoregular and high-molecular polypiperylene

  20. Arsenates of rare-metals: electrometric investigations on praseodymium arsenates as a function of pH

    Energy Technology Data Exchange (ETDEWEB)

    Prasad, S [Paraiba Univ., Joao Pessoa (Brazil). Dept. de Engenharia Quimica

    1982-01-01

    The stoichiometry of the compounds formed by the interaction of praseodymium chloride and different alkali arsenates (meta, pyro and ortho) at specific pH levels - 7.2, 8.3 and 11.1 - was investigated by electrometric techniques involving pH measurements and potentiometric and conductometric titrations. The inflections and breaks in the titration curves provide evidence for the formation of three praseodymium arsenates having the molecular formulae Pr/sub 2/O/sub 3/.3 As/sub 2/O/sub 5/, 2Pr/sub 2/O/sub 3/.3As/sub 2/O/sub 5/ and Pr2O/sub 3/.As/sub 2/O/sub 5/ in the vicinity of pH 4.8, 5.8 and 7.0, respectively. Analysis of the compounds by conventional methods (gravimetric, as oxide, for praseodymium; iodometric for arsenic) substantiate the results of the electrometric study

  1. Lanthanum

    Science.gov (United States)

    ... levels of phosphate in the blood can cause bone problems. Lanthanum is in a clsas of medications ... to your pharmacist or contact your local garbage/recycling department to learn about take-back programs in ...

  2. Complex-formation of praseodymium and neodymium in non aqueous solutions

    International Nuclear Information System (INIS)

    Schuetz, R.

    1966-03-01

    Chlorides and acides of Neodymium(III) and Praseodymium(III) were prepared in waterfree Dimethylsulfoxide, Trimethylphosphate and Dimethylformamide. The amount and kinetics of solvatisation and dissociation in these solvents was measured with spectrophotometric, conductometric and potentiometric methods. (P.W.)

  3. Determination of formation constants of hydroxo carbonate complexes of Pr{sup 3+} in 2M NaCl at 303 K; Determinacion de las constantes de hidrolisis y de los complejos con carbonatos del Praseodimio (III), en medio de fuerza ionica 2M de cloruro de sodio, a 303 K

    Energy Technology Data Exchange (ETDEWEB)

    Lopez G, H D

    1997-12-31

    The hydrolysis of Praseodymium III in 2M sodium chloride at 303 K was studied. Two methods were used: pH titration followed by a computational refinement and solvent extraction in the presence of a competitive ligand. The hydrolysis constants obtained by pH titration were: log {beta}{sub 1,H} = -7.68 {+-} 0.07, log {beta}{sub 1,2H} = -15.10 {+-} 0.03, and {beta}{sub 1,3H} -23.8 {+-} 0.04. The stability constants of Praseodymium carbonates were determined by pH titration as well and were: log {beta}{sub 1,CO3}{sup 2-} = 5.94 {+-} 0.08 and log {beta}{sub 1,2CO3}{sup 2-} = 11.15 {+-} 0.15. Praseodymium carbonate species were taken into consideration for calculating the first hydrolysis constants by the solvent extraction method and the value obtained was: log {beta}{sub 1,H} = -7.69 {+-} 0.27. The values for log {beta}{sub 1,H} attained by both methods are the same. The species-distribution diagram was obtained from the stability constants of Praseodymium carbonates and hydrolysis products in the conditions of the present work. (Author).

  4. Determination of formation constants of hydroxo carbonate complexes of Pr3+ in 2M NaCl at 303 K

    International Nuclear Information System (INIS)

    Lopez G, H.D.

    1996-01-01

    The hydrolysis of Praseodymium III in 2M sodium chloride at 303 K was studied. Two methods were used: pH titration followed by a computational refinement and solvent extraction in the presence of a competitive ligand. The hydrolysis constants obtained by pH titration were: log β 1,H = -7.68 ± 0.07, log β 1,2H = -15.10 ± 0.03, and β 1,3H -23.8 ± 0.04. The stability constants of Praseodymium carbonates were determined by pH titration as well and were: log β 1,CO3 2- = 5.94 ± 0.08 and log β 1,2CO3 2- = 11.15 ± 0.15. Praseodymium carbonate species were taken into consideration for calculating the first hydrolysis constants by the solvent extraction method and the value obtained was: log β 1,H = -7.69 ± 0.27. The values for log β 1,H attained by both methods are the same. The species-distribution diagram was obtained from the stability constants of Praseodymium carbonates and hydrolysis products in the conditions of the present work. (Author)

  5. Crystal and molecular structure of praseodymium nitrate dipivalate adduct with o-phenanthroline

    International Nuclear Information System (INIS)

    Pisarevskij, A.P.; Mitrofanova, N.D.; Frolovskaya, S.N.; Martynenko, L.I.

    1995-01-01

    The paper deals with the synthesis and X-ray diffraction investigation of praseodymium nitrate dipivalate adduct with o-phenanthroline of PrPiv 2 (NO 3 )Phen 2 composition. The crystals are triclinic: a = 9.738(4), b = 11.860(5), c = 15.451(6) A, α = 91.80(2), β = 99.41(2), γ = 103.69(2) deg, sp. gr. P1, d cald = 1.490 g/cm 3 . The coordination number of praseodymium atom in a monomeric molecule equals 10, both carboxylate groups and nitrate ion are coordinated by the bidentate-cyclic method. Phenanthroline molecules are formed by five-membered chelate cycles in the process of coordination. 5 refs., 1 fig., 2 tab

  6. Lanthanum Containing Polymer's Modification to PP

    Institute of Scientific and Technical Information of China (English)

    Dai Shaojun; Zhang Ming

    2004-01-01

    Polypropylene (PP)'s low impact strength limits its usages. Adding some a rare earth polymer can enhance PP's tensile strength and impact strength. Acrylic lanthanum was prepared by the reaction between lanthanum oxide and acrylic acid. The IR spectrum prove that and optimum reacting conditions are that the bulk ratio of La(AA) 3 and MMA is not less than one and temperature is about 80 ℃. Lanthanum containing Polymer were added into PP. When percent of addition only was 3%, strength were enhanced 10% , and impact strength 40%. SEM shows the compatibility of rare earth polymer and PP; lanthanum containing polymer can form physical crosslinking between PP's molecules, then every particle's surface connect with several PP molecules and the PP mechanical property were enhanced.

  7. Corrosion and electrochemical properties of lanthanum

    International Nuclear Information System (INIS)

    Tomashov, N.D.; Matveeva, T.V.

    The kinetics of the corrosion rate of lanthanum at 25 0 in air of different relative humidities, distilled water, sulfuric acid, hydrochloric acid, nitric acid, phosphoric acid, hydrofluoric acid, potassium hydroxide of different concentrations and at 100 0 C in distilled water and potassium hydroxide have been studied. In air at 22--100% relative humidity, the corrosion rate of lanthanum increases with time and with increasing humidity. In distilled water and in potassium hydroxide solutions, the corrosion rate of lanthanum increases with time and decreasees when the concentration of alkali exceeds 20%. With increasing concentration of the acids, the corrosion rate of lanthanum increases in hydrochloric acid and nitric acid and passes through a maximum in sulfuric acid (20%) and phosphoric acid (60%). The values of the corrosion rates of lanthanum in 40% nitric acid, 35% hydrochloric acid, 20% sulfuric acid, 60% phosphoric acid, and 40% hydrofluoric acid are 8 x 10 5 ; 4.4 x 10 4 ; 1.3 x 10 3 ; 9 g/m 2 h respectively

  8. Complexometric determination of lanthanum and calcium in lanthanum chromite

    International Nuclear Information System (INIS)

    Novoselova, I.M.

    1989-01-01

    Methods of complexometric determination of lanthanum and calcium in lanthanum chromite, based on sequential titration of La and Ca by EDTA solution, where as an indicator eriochrome brack T with NaCl mixture in the ratio of 1:100 is used, are determined. Cr (3) effect was removed by its oxidation up to Cr (6) with perchloric acid; at first La was determined in presence of urotropine buffer, then Ca at pH 9.5-10 in presence of ammonia buffer. For reaction acceleration method of back titration of EDTA excess by zinc salt solution was used. Standard deviation in La and Ca determination is not over 0.2 and 0.1 % respectively

  9. The Influence of Lactic Acid Concentration on the Separation of Light Rare Earth Elements by Continuous Liquid-Liquid Extraction with 2-Ethylhexyl Phosphonic Acid Mono-2-ethylhexyl Ester

    Science.gov (United States)

    de Carvalho Gomes, Rafael; Seruff, Luciana Amaral; Scal, Maira Labanca Waineraich; Vera, Ysrael Marrero

    2018-02-01

    The separation of rare earth elements (REEs) using solvent extraction adding complexing agents appears to be an alternative to saponification of the extractant. We evaluated the effect of lactic acid concentration on didymium (praseodymium and neodymium) and lanthanum extraction with 2-ethylhexyl phosphonic acid mono-2-ethyl hexyl ester [HEH(EHP)] as extractant. First, we investigated in batch experiments the separation of lanthanum (La) and didymium (Pr and Nd) using McCabe-Thiele diagrams to estimate the number of extraction stages when the feed solution was or was not conditioned with lactic acid. Additionally, we conducted continuous liquid-liquid extraction experiments and evaluated the influence of lactic acid concentration on the REE extraction and separation. The tests showed that the extraction percentage of REEs and the separation factor Pr/La increased when the lactic acid concentration increased, but the didymium purity decreased. Lanthanum, praseodymium, and neodymium extraction rate were 23.0, 89.7, and 99.2 pct, respectively, with 1:1 aqueous/organic volume flow rate and feed solution doped with 0.52 mol L-1 lactic acid. The highest didymium purity reached was 92.0 pct with 0.26 mol L-1 lactic acid concentration.

  10. Thermoelectric properties of non-stoichiometric lanthanum sulfides

    International Nuclear Information System (INIS)

    Shapiro, E.; Danielson, L.R.

    1983-01-01

    The lanthanum sulfides are promising candidate materials for high-efficiency thermoelectric applications at temperatures up to 1300 0 C. The nonstoichiometric lanthanum sulfides (LaS /SUB x/ , where 1.33 2 //rho/ can be chosen. The thermal conductivity remains approximately constant with stoichiometry, so a material with an optimum value of α 2 //rho/ should possess the optimum figure-of-merit. Data for the Seebeck coefficient and electrical resistivity of non-stoichiometric lanthanum sulfides is presented, together with structural properties of these materials

  11. Preparation and characterization of perovskite structure lanthanum gallate and lanthanum aluminate based oxides

    OpenAIRE

    Li, Shuai

    2009-01-01

    The present work was initiated to study the synthesis and properties of lanthanum gallate based oxides as intermediate temperature electrolyte for solid oxide fuel cells. The wet chemical method, polymer complexing route, was used to prepare the precursor powders. To further investigate the polymer complexing method, it was also applied to the preparation of lanthanum aluminate based oxides.   Single perovskite phase La0.8Sr0.2Ga0.83Mg0.17O2.815 can be prepared by the polymer complexing meth...

  12. Adsorption of lithium-lanthanum films on the (100) tungsten face

    International Nuclear Information System (INIS)

    Gupalo, M.S.; Smereka, T.P.; Babkin, G.V.; Palyukh, B.M.

    1982-01-01

    The method of contact potential difference is used to investigate combined adsorption of lithium-lanthanum on the (100) tungsten face. The data on work functions and thermal stability of mixed lithium-lanthanum films are obtained. The presence of lanthanum on the W(100) surface leads to appearance of minimum of work functions unobserved for the Li-W(100) system, minimum work functions and optimum lithium concentration in a mixed film are decreased at initial lanthanum coating increase. The presence of lanthanum on the W(100) face leads to lithium adsorption heat decrease

  13. High field magnetic anisotropy in praseodymium gallium garnet at low temperatures

    International Nuclear Information System (INIS)

    Wang Wei; Yue Yuan; Liu Gongqiang

    2011-01-01

    Research highlights: → A detailed analysis of crystal field effect is presented, and a set of new crystal field parameters is given to study the magnetic behaviors of the paramagnetic praseodymium gallium garnet (PrGaG). → The contribution of the exchange interaction between the praseodymium ions to the magnetic properties of PrGaG is further explored. Meanwhile, some characteristics of exchange interaction are revealed. → With the consideration of crystal field and exchange interaction, the available experiments are successfully fitted by our theoretical model. → Our theory suggests that PrGaG is ferromagnetic ordering at low temperatures, and the exchange interaction is anisotropic. - Abstract: In this paper, with the consideration of crystal field and exchange interaction between the rare-earth Pr 3+ ions, the magnetic anisotropy in praseodymium gallium garnet (PrGaG) in high magnetic fields and at low temperatures is theoretically analyzed. A set of relatively suitable CF parameters is obtained by studying the influence of the variations of nine CF parameters on the magnetization. However, only taking crystal field effect into account, theoretical calculations indicate that the experiments cannot be excellently interpreted. Then, the exchange interaction between Pr 3+ ion, which can be described as an effective exchange field H v = vM = vχH e = ηH e , is further considered. On the other hand, by evaluating the variation of the parameter η with the magnetic fields, our theory implies that PrGaG exhibits ferrimagnetic ordering at low temperatures, and the exchange interaction in PrGaG displays obvious anisotropy. Also, the theoretical data show better agreements with the experimental results.

  14. Nanoscale assembly of lanthanum silica with dense and porous interfacial structures.

    Science.gov (United States)

    Ballinger, Benjamin; Motuzas, Julius; Miller, Christopher R; Smart, Simon; Diniz da Costa, João C

    2015-02-03

    This work reports on the nanoscale assembly of hybrid lanthanum oxide and silica structures, which form patterns of interfacial dense and porous networks. It was found that increasing the molar ratio of lanthanum nitrate to tetraethyl orthosilicate (TEOS) in an acid catalysed sol-gel process alters the expected microporous metal oxide silica structure to a predominantly mesoporous structure above a critical lanthanum concentration. This change manifests itself by the formation of a lanthanum silicate phase, which results from the reaction of lanthanum oxide nanoparticles with the silica matrix. This process converts the microporous silica into the denser silicate phase. Above a lanthanum to silica ratio of 0.15, the combination of growth and microporous silica consumption results in the formation of nanoscale hybrid lanthanum oxides, with the inter-nano-domain spacing forming mesoporous volume. As the size of these nano-domains increases with concentration, so does the mesoporous volume. The absence of lanthanum hydroxide (La(OH)3) suggests the formation of La2O3 surrounded by lanthanum silicate.

  15. Investigation of the hyperfine structure of Praseodymium-transitions using laser spectroscopy

    International Nuclear Information System (INIS)

    Shamim Khan

    2011-01-01

    A comprehensive knowledge of the electron levels in an atom is one of the prerequisite for understanding the electron-electron and electron-nucleus interactions inside an atom and for the classification of the atomic spectrum of an element. The spin-orbit interaction is the largest relativistic effect and is responsible for the fine structure splitting in an atom. The hyperfine structure splitting of the fine structure atomic energy levels arise as a result of the interaction between spinning and orbiting electrons and electromagnetic multipole nuclear moments. The electronic ground state configuration of praseodymium 59 Pr 141 is [Xe] 4f 3 6s 2 , with ground state level 4 I 9/2 . Because of its 5 outer electrons Praseodymium has a high density of energy levels which give rise to an extremely line rich emission spectrum. Due to this fact praseodymium serves as an efficient testing ground for hyperfine structure studies. The thesis is mainly devoted to the finding of previously unknown energy levels by the investigation of spectral lines and their hyperfine structures. In a hollow cathode discharge lamp praseodymium atoms and ions in ground and excited states are excited to high lying states by laser light. The excitation source is a tunable ring-dye laser system, operated with Stilbene 3, Rhodamine 6G, Kiton Red, DCM and LD 700. A high resolution Fourier Transform spectrum is used for extracting excitation wavelengths. Then the laser wavelength is tuned to a strong hyperfine component of the spectral line to be investigated, and a search for fluorescence from excited levels is performed. From the observed hyperfine structure pattern, J-values and hyperfine interaction constants A of the combining levels are determined. This information, together with excitation and fluorescence wavelengths, allows us to find the energies of the involved levels. During the course of this dissertation 313 new energy levels of Pr I and 4 new energy levels of Pr II were discovered

  16. Lanthanum deposition corresponds to white lesions in the stomach.

    Science.gov (United States)

    Iwamuro, Masaya; Urata, Haruo; Tanaka, Takehiro; Kawano, Seiji; Kawahara, Yoshiro; Kimoto, Katsuhiko; Okada, Hiroyuki

    2018-05-23

    Although lanthanum deposition in the stomach has been most frequently reported to occur as white lesions, no study has investigated whether the white lesions observed during esophagogastroduodenoscopy are truly lanthanum-related. Here, we retrospectively investigated the amount of lanthanum in endoscopic biopsy specimens. We reviewed four patients showing gastric white spots or annular whitish mucosa in the gastric white lesions (Bw) and peripheral mucosa where the white substance was not endoscopically observed (Bp) during biopsy. We also reviewed three patients with diffuse whitish mucosa and three patients with no whitish lesions. We performed scanning electron microscopy and energy dispersive X-ray spectrometry to quantify the lanthanum elements (wt%) in the biopsy specimens. The amount of lanthanum in the Bw ranged from 0.15-0.31 wt%, whereas that of Bp was 0.00-0.13 wt%. The difference was statistically significant (P < 0.05). The amount of lanthanum in the Bw, endoscopically presented with white spots or annular whitish mucosa, was significantly higher than that of no whitish lesions (0.05-0.14 wt%, P < 0.05). The amount of lanthanum was also higher in the diffuse whitish mucosa (0.21-0.23 wt%) compared with no whitish lesions (P < 0.01). This study is the first to reveal that pathological lanthanum deposition corresponds to the endoscopically observed white lesions in the gastric mucosa. Therefore, during esophagogastroduodenoscopy, physicians should pay attention to possible presence of white lesions in patients treated with oral lanthanum carbonate to ensure prompt identification of associated issues. Copyright © 2018 Elsevier GmbH. All rights reserved.

  17. Mechanical properties of dense to porous alumina/lanthanum hexaaluminate composite ceramics

    International Nuclear Information System (INIS)

    Negahdari, Zahra; Willert-Porada, Monika; Pfeiffer, Carolin

    2010-01-01

    For development of new composite materials based on lanthanum hexaaluminate and alumina ceramics, a better understanding of the microstructure-properties relationship is essential. In this paper, attention was focused on the evaluation of mechanical properties of lanthanum hexaaluminate/alumina particulate composite. It was found out that the lanthanum hexaaluminate content plays a critical role in determination of the microstructure and mechanical properties of the composite ceramics. In situ formation of plate-like lanthanum hexaaluminate in the ceramic matrix was accompanied with formation of pores so that the microstructure shifted from dense to porous. Increasing the lanthanum hexaaluminate content up to a certain value enhanced the fracture toughness, increased the hardness, and increased the elastic modulus of the composite materials. Further increase in the lanthanum hexaaluminate content degraded the hardness as well as the elastic modulus of composite ceramics. The influence of lanthanum hexaaluminate on mechanical properties was described by means of microstructure, porosity, and intrinsic characteristics of lanthanum hexaaluminate.

  18. Comparative studies of praseodymium(III) selective sensors based on newly synthesized Schiff's bases

    International Nuclear Information System (INIS)

    Gupta, Vinod K.; Goyal, Rajendra N.; Pal, Manoj K.; Sharma, Ram A.

    2009-01-01

    Praseodymium ion selective polyvinyl chloride (PVC) membrane sensors, based on two new Schiff's bases 1,3-diphenylpropane-1,3-diylidenebis(azan-1-ylidene)diphenol (M 1 ) and N,N'-bis(pyridoxylideneiminato) ethylene (M 2 ) have been developed and studied. The sensor having membrane composition of PVC: o-NPOE: ionophore (M 1 ): NaTPB (w/w; mg) of 150: 300: 8: 5 showed best performances in comparison to M 2 based membranes. The sensor based on (M 1 ) exhibits the working concentration range 1.0 x 10 -8 to 1.0 x 10 -2 M with a detection limit of 5.0 x 10 -9 M and a Nernstian slope 20.0 ± 0.3 mV decade -1 of activity. It exhibited a quick response time as <8 s and its potential responses were pH independent across the range of 3.5-8.5.The influence of the membrane composition and possible interfering ions have also been investigated on the response properties of the electrode. The sensor has been found to work satisfactorily in partially non-aqueous media up to 15% (v/v) content of methanol, ethanol or acetonitrile and could be used for a period of 3 months. The selectivity coefficients determined by using fixed interference method (FIM) indicate high selectivity for praseodymium(III) ions over wide variety of other cations. To asses its analytical applicability the prepared sensor was successfully applied for determination of praseodymium(III) in spiked water samples.

  19. Dielectric and impedance study of praseodymium substituted Mg-based spinel ferrites

    Energy Technology Data Exchange (ETDEWEB)

    Farid, Hafiz Muhammad Tahir, E-mail: tahirfaridbzu@gmail.com [Department of Physics, Bahauddin Zakariya, University Multan, 60800 (Pakistan); Ahmad, Ishtiaq; Ali, Irshad [Department of Physics, Bahauddin Zakariya, University Multan, 60800 (Pakistan); Ramay, Shahid M. [College of Science, Physics and Astronomy Department, King Saud University, P.O. Box 2455, 11451 Riyadh (Saudi Arabia); Mahmood, Asif [Chemical Engineering Department, College of Engineering, King Saud University, Riyadh (Saudi Arabia); Murtaza, G. [Centre for Advanced Studies in Physics, GC University, Lahore 5400 (Pakistan)

    2017-07-15

    Highlights: • Magnesium based spinel ferrites were successfully synthesized by sol-gel method. • Dielectric constant shows the normal spinel ferrites behavior. • The dc conductivity are found to decrease with increasing temperature. • The samples with low conductivity have high values of activation energy. • The Impedance decreases with increasing frequency of applied field. - Abstract: Spinel ferrites with nominal composition MgPr{sub y}Fe{sub 2−y}O{sub 4} (y = 0.00, 0.025, 0.05, 0.075, 0.10) were prepared by sol-gel method. Temperature dependent DC electrical conductivity and drift mobility were found in good agreement with each other, reflecting semiconducting behavior. The dielectric properties of all the samples as a function of frequency (1 MHz–3 GHz) were measured at room temperature. The dielectric constant and complex dielectric constant of these samples decreased with the increase of praseodymium concentration. In the present spinel ferrite, Cole–Cole plots were used to separate the grain and grain boundary’s effects. The substitution of praseodymium ions in Mg-based spinel ferrites leads to a remarkable rise of grain boundary’s resistance as compared to the grain’s resistance. As both AC conductivity and Cole–Cole plots are the functions of concentration, they reveal the dominant contribution of grain boundaries in the conduction mechanism. AC activation energy was lower than dc activation energy. Temperature dependence normalized AC susceptibility of spinel ferrites reveals that MgFe{sub 2}O{sub 4} exhibits multi domain (MD) structure with high Curie temperature while on substitution of praseodymium, MD to SD transitions occurs. The low values of conductivity and low dielectric loss make these materials best candidate for high frequency application.

  20. Electrochemical properties of lanthanum nitride with calcium nitride additions

    International Nuclear Information System (INIS)

    Lesunova, R.P.; Fishman, L.S.

    1986-01-01

    This paper reports on the electrochemical properties of lanthanum nitride with calcium nitride added. The lanthanum nitride was obtained by nitriding metallic lanthanum at 870 K in an ammonia stream. The product contained Cl, Pr, Nd, Sm, Fe, Ca, Cu, Mo, Mg, Al, Si, and Be. The calcium nitride was obtained by nitriding metallic calcium in a nitrogen stream. The conductivity on the LaN/C 3 N 2 system components are shown as a function of temperature. A table shows the solid solutions to be virtually electronic conductors and the lanthanum nitride a mixed conductor

  1. Optical absorption and fluorescence studies of praseodymium ion in chloroborophosphate glasses

    International Nuclear Information System (INIS)

    Sharma, Y.K.; Tandon, S.P.

    1998-01-01

    Full text: The interest in optical absorption and fluorescence studies of rare earth ions in glassy materials is increasing continuously in connection with laser research and related application. The absorption and fluorescence spectra of praseodymium ion in chloroborophosphate glasses have been recorded at room temperature. The chloroborophosphate glass specimens having composition in mob.% Na 2 0 (26.08), B 2 0 3 (14.57), P 2 0 5 (44.85), ZnCl 2 (14.50), Pr 6 0 11 (R) [R= 0.0,0.1 and 0.2 moi.%] have been prepared by melt quenching technique. The spectra consists of seven absorption bands and three fluorescence bands. The observed optical spectra are discussed in terms of energy state and the intensity of the transitions. The various energy interaction parameters like Slater-Condon, Lande', Racah and bonding parameters have been computed. Judd-Ofeit intensity parameters and laser parameters have also been computed. These results shows that praseodymium doped chloroborophosphate glass specimen can be considered as good hosts for laser applications

  2. Luminescent characteristics of praseodymium-doped zinc aluminate powders

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Perez, C.D.; Garcia-Hipolito, M.; Alvarez-Fregoso, O. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Coyoacan, DF (Mexico); Alvarez-Perez, M.A. [Facultad de Odontologia, Universidad Nacional Autonoma de Mexico, Coyoacan, DF (Mexico); Ramos-Brito, F. [Laboratorio de Materiales Optoelectronicos, DIDe, Centro de Ciencias de Sinaloa, Av. De las Americas No. 2771 Nte. Col. Villa Universidad, Culiacan, Sinaloa (Mexico); Falcony, C. [Centro de Investigaciones y Estudios Avanzados del IPN, Departamento de Fisica, Mexico, DF (Mexico)

    2010-02-15

    In this research, we report the cathodoluminescence (CL) and preliminary photoluminescence (PL) properties of praseodymium-doped zinc aluminate powders. ZnAl{sub 2}O{sub 4}:Pr powders were synthesized by a very simple chemical process. X-ray diffraction spectra indicated a cubic spinel crystalline structure with an average crystallite size of 15 nm. CL properties of the powders were studied as a function of the praseodymium concentration and electron-accelerating potential. In this case, all the cathodoluminescent emission spectra showed main peaks located at 494, 535, 611, 646, and 733 nm, which were associated to the electronic transitions {sup 3}P{sub 0}{yields}{sup 3}H{sub 4}, {sup 3}P{sub 0}{yields}{sup 3}H{sub 5}, {sup 3}P{sub 0}{yields}{sup 3}H{sub 6}, {sup 3}P{sub 0}{yields}{sup 3}F{sub 2}, and {sup 3}P{sub 0}{yields}{sup 3}F{sub 4} of the Pr{sup 3+} ions, respectively. A quenching of the CL, with increasing doping concentration, was observed. Also, an increment on cathodoluminescent emission intensity was observed as the accelerating voltage increased. The PL emission spectrum showed similar characteristics to those of the CL spectra. The chemical composition of the powders, as determined by energy dispersive spectroscopy, is also reported. In addition, the surface morphology characteristics of the powders are shown. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  3. Mechanical and thermal properties of praseodymium monochalcogenides and monopnictides under pressure

    International Nuclear Information System (INIS)

    Bhajanker, Sanjay; Srivastava, V.; Pagare, G.; Sanyal, S.P.

    2011-01-01

    In recent years, a great deal of interest has been focused on rare-earth chalcogenides and pnictides because they have numerous applications in technologies. The praseodymium chalcogenides have attracted great attention due to their potential application in spintronics, spin filtering devices, hyperfine enhanced nuclear cooling, study of combined electron and nuclear order phenomenon at very low temperature

  4. Preparation and Characterization of Lanthanum Carbonate Octahydrate for the Treatment of Hyperphosphatemia

    Directory of Open Access Journals (Sweden)

    Anqi He

    2013-01-01

    Full Text Available We proposed a new approach to prepare lanthanum carbonate via reactions between lanthanum chloride and NaHCO3. In the reaction, small amount of NaHCO3 solution was firstly added to the acidic lanthanum chloride solution to generate lanthanum carbonate nuclei and then NaHCO3 is added to the lanthanum chloride at a constant speed. This approach makes both precipitation reaction and neutralization reaction take place simultaneously. Consequently, lanthanum carbonate is produced at low pH environment (pH below 4.0 so that the risk of generating lanthanum carbonate hydroxide is reduced. The product of the above reaction is validated by EDTA titration, elemental analysis, and XRD characterization. In addition, we established a FTIR spectroscopic method to identify La(OHCO3 from La2(CO32·8H2O. Lanthanum carbonate exhibits considerable ability to bind phosphate.

  5. Preparation of lanthanum sulfide nanoparticles by thermal decomposition of lanthanum complex

    Institute of Scientific and Technical Information of China (English)

    LI Peisen; LI Huanyong; JIE Wanqi

    2011-01-01

    γ-La2S3 nanoparticles were successfully prepared by thermal decomposition of lanthanum complex La(Et2S2CN)3·phen at low temperature. The obtained sample was characterized by the X-ray powder diffraction (XRD), scanning electron microscopy (SEM) and element analysis. The decomposition mechanism of lanthanum complex was studied by thermogravimetric analyses (TGA). The results showed that the obtained samples were cubic phase particles with uniform sizes among 10-30 nm and γ-La2S3 was prepared by decomposition of La(Et2S2CN)3 phen via La4(Et2S2CN)3 as an intermediate product. The band gap of γ-La2S3 was 2.97 eV, which was bigger than bulk crystal because of pronounced quantum confinement effect.

  6. New energy levels of praseodymium with large angular momentum

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Shamim; Siddiqui, Imran; Gamper, Bettina; Syed, Tanweer Iqbal; Guthoehrlein, Guenter H.; Windholz, Laurentius [Inst. f. Experimentalphysik, Techn. Univ. Graz, Petersgasse 16, A-8010 Graz (Austria)

    2011-07-01

    The electronic ground state configuration of praseodymium {sup 59}Pr{sub 141} is [Xe] 4f{sup 3}6s{sup 2}, with ground state level {sup 4}I{sub 9/2}. Our research is mainly devoted to find previously unknown energy levels by the investigation of spectral lines and their hyperfine structures. In a hollow cathode discharge lamp praseodymium atoms and ions in ground and excited states are excited to high lying states by laser light. The excitation source is a tunable ring-dye laser system, operated with R6G, Kiton Red, DCM and LD700. A high resolution Fourier transform spectrum is used for selecting promising excitation wavelengths. Then the laser wavelength is tuned to a strong hyperfine component of the spectral line to be investigated, and a search for fluorescence from excited levels is performed. From the observed hyperfine structure we determine J-values and hyperfine constants A of the combining levels. This information, together with excitation and fluorescence wavelengths, allows us to find the energies of involved new levels. Up to now we have discovered large number of previously unknown energy levels with various angular momentum values. We present here the data (energies, parities, angular momenta J, magnetic hyperfine constants A) of ca. 40 new, until now unknown energy levels with high angular momentum values: 15/2, 17/2, 19/2, 21/2.

  7. Perovskite catalysts for oxidative coupling

    Science.gov (United States)

    Campbell, Kenneth D.

    1991-01-01

    Perovskites of the structure A.sub.2 B.sub.2 C.sub.3 O.sub.10 are useful as catalysts for the oxidative coupling of lower alkane to heavier hydrocarbons. A is alkali metal; B is lanthanide or lanthanum, cerium, neodymium, samarium, praseodymium, gadolinium or dysprosium; and C is titanium.

  8. Synthesis in aqueous medium and organic praseodymium complexes with ligands derived from Schiff base quinolinic. Characterization and physicochemical study

    International Nuclear Information System (INIS)

    Garcia G, A.

    2015-01-01

    It was investigated the coordination ability of the quinolinic Schiff base organic tetradentate quinolinic ligand (Q Schiff-(OH) 2 ) towards the trivalent praseodymium by UV/Vis spectrophotometric titration (St). By St, was studied the formed species between the Q Schiff-(OH) 2 ligand and the praseodymium nitrate salt in equimolar concentrations (5.86 x 10 -4 M: 5.22 x 10 -4 M) in methanol. The statistical analysis of the experimental results suggested three complexed species with 1Pr:3L, 1Pr:2L y 1Pr:1L stoichiometries. The predominant stoichiometries were the second and the latter. Based on these results and data from the scientific literature, the methodology for the syntheses of the complexes Q Schiff-(OH) 2 -Pr in aqueous-organic and organic media was established and a molar ratio M:L= 1:2 of praseodymium nitrate and the ligand was used. The new complexes were characterized by UV/Vis, Infrared, X-ray Photoelectron Spectroscopy (XP S), Diffuse Reflectance (Dr) and Thermogravimetric Analysis/Differential Scanning Calorimetry (TGA/DSC). Elemental analysis of C, N, O and Pr by XP S suggested 1Pr:2L:1Na (PrC 32 H 20 N 4 O 4 Na) stoichiometry of the complex synthesized by the aqueous-organic medium while for the complex synthesized by the organic medium it was 1Pr:3L (PrC 48 H 33 N 6 O 6 ). In the first case, the praseodymium ion charge was neutralized by the anionic ligands whose remaining charge was compensated by the sodium ion. In the second case, the ion charge was neutralized by the ligands. The minimum formula was Pr(Q Schiff) 2 Na for the pure coordination compound from the aqueous-organic medium and the minimum formula Pr(Q Schiff) 3 for that from the organic medium. XP S also indicated that the oxidation state of praseodymium ion was maintained. Both complexes were stable in methanol, ethanol and acetonitrile at least for 5 days. The photophysical properties of the studied complexes were evaluated by emission and excitation luminescence (fluorescence and

  9. Fuel cells with doped lanthanum gallate electrolyte

    Science.gov (United States)

    Feng, Man; Goodenough, John B.; Huang, Keqin; Milliken, Christopher

    Single cells with doped lanthanum gallate electrolyte material were constructed and tested from 600 to 800°C. Both ceria and the electrolyte material were mixed with NiO powder respectively to form composite anodes. Doped lanthanum cobaltite was used exclusively as the cathode material. While high power density from the solid oxide fuel cells at 800°C was achieved. our results clearly indicate that anode overpotential is the dominant factor in the power loss of the cells. Better anode materials and anode processing methods need to be found to fully utilize the high ionic conductivity of the doped lanthanum galiate and achieve higher power density at 800°C from solid oxide fuel cells.

  10. Fuel cells with doped lanthanum gallate electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Feng Man [Texas Univ., Austin, TX (United States). Center for Materials Science and Engineering; Goodenough, J.B. [Texas Univ., Austin, TX (United States). Center for Materials Science and Engineering; Huang Keqin [Texas Univ., Austin, TX (United States). Center for Materials Science and Engineering; Milliken, C. [Cerematec, Inc., Salt Lake City, UT (United States)

    1996-11-01

    Single cells with doped lanthanum gallate electrolyte material were constructed and tested from 600 to 800 C. Both ceria and the electrolyte material were mixed with NiO powder respectively to form composite anodes. Doped lanthanum cobaltite was used exclusively as the cathode material. While high power density from the solid oxide fuel cells at 800 C was achieved, our results clearly indicate that anode overpotential is the dominant factor in the power loss of the cells. Better anode materials and anode processing methods need to be found to fully utilize the high ionic conductivity of the doped lanthanum gallate and achieve higher power density at 800 C from solid oxide fuel cells. (orig.)

  11. Process for obtaining cobalt and lanthanum nickelate

    International Nuclear Information System (INIS)

    Tapcov, V.; Samusi, N.; Gulea, A.; Horosun, I.; Stasiuc, V.; Petrenco, P.

    1999-01-01

    The invention relates to the process for obtaining polycrystalline ceramics of cobalt and lanthanum nickelate with the perovskite structure from coordinative hetero metallic compounds. The obtained products can be utilized in the industry in the capacity of catalysts. Summary of the invention consists in obtaining polycrystalline ceramics LaCoO 3 and LaNiO 3 with the perovskite structure by pyrolysis of the parent compounds, namely, the coordinative hetero metallic compounds of the lanthanum cobalt or lanthanum nickel. The pyrolysis of the parent compound runs during one hour at 800 C. The technical result of the invention consists in lowering the temperature of the parent compound pyrolysis containing the precise ratio of metals necessary for ceramics obtaining

  12. Calibration curves for quantifying praseodymium by UV-VIS; Curvas de calibracion para cuantificar praseodimio por UV-VIS

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez M, R.; Lopez G, H.; Rojas H, A. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)]. e-mail: robertssd1199@yahoo.com.mx

    2007-07-01

    The UV-Vis spectroscopic technique was used to determine the absorption bands depending on the concentration from the praseodymium solutions at pH3. Those more appropriate were in the wavelength of 215 nm, for concentrations of 0.0001-0.026 M, of 481nm, 468 nm and 443 nm, for concentrations of 0.026-0.325 M, and of 589 nm, for concentrations of 0.026-0.65 M of the praseodymium. To these wavelengths the calibration curves were determined, which presented correlation coefficients between 0.9976 and 0.9999 except of the absorption of 589 nm that gave R{sup 2} = 0.9014. (Author)

  13. High-temperature corrosion of lanthanum in equimole mixture of sodium and potassium chlorides

    International Nuclear Information System (INIS)

    Kochergin, V.P.; Obozhina, R.N.; Dragoshanskaya, T.I.; Startsev, B.P.

    1984-01-01

    Results of investigation into the process of lanthanum corrosion in the molted equimole NaCl-KCl mixture after the change of test time, temperature and lanthanum trichloride were summarized. It was shown that polarization of lanthanum anode in equimole NaCl-KCl melt is controlled by La 3+ diffusion from near-electrode layer to electrolyte depth, which results in decrease of corrosion rate in time. The established electrochemical properties of metallic lanthanum in equimole NaCl-KCl mixture must be considered when improving the technology of electrochemical production of lanthanum or its alloys of molten chlorides of lanthanum and alkaline metals

  14. Study in aqueous solution of the praseodymium inclusion in β-cyclodextrin in 2 M of NaCl; Estudio en solucion acuosa de la inclusion del praseodimio en la β-ciclodextrina en 2 M de NaCl

    Energy Technology Data Exchange (ETDEWEB)

    De la Cruz M, N.

    2013-07-01

    In the fission of uranium to produce electricity, generated between the fission products which are the lanthanides and actinides that at any given time may come into contact with aqueous media, because of this, praseodymium was including in the β-cyclodextrin in order to increase the solubility and stability of praseodymium by forming inclusion complexes Praseodymium-β-cyclodextrin (Pr-β-Cd). The inclusion study was conducted in a proportion of praseodymium and β-cyclodextrin. Infrared spectra, Raman and X-ray diffraction showed the presence of praseodymium and β-cyclodextrin in the inclusion complex, in both proportions. The analysis by scanning electron microscopy confirmed the inclusion of praseodymium in βcyclodextrin. In general, the results of characterization obtained by these techniques show the formation of the inclusion complex. Furthermore, the behaviour of praseodymium inclusion in the β-cyclodextrin was studied in 2 M NaCl at 303 K and free-CO{sub 2} conditions. For this reason, we used two methods: spectrophotometric and potentiometric titration direct of praseodymium-β-cyclodextrin, the data were treated graphically and with the program SUPERQUAD, respectively. The values obtained for praseodymium by spectrophotometric method was: log β{sub 1}= -8.75 calculated graphically and with the potentiometric method, using program SUPERQUAD were logβ{sub 1,OH}= -8.73 ± 0.01 logβ{sub 1,2OH}= -18.27 ± 0.16 and logβ{sub 1,3OH}= -26.44 ± 0.02 obtained simultaneously. (Author)

  15. Theory of singlet-doublet excitations in praseodymium

    International Nuclear Information System (INIS)

    Bak, P.

    1975-10-01

    The magnetic excitation spectrum in a paramagnetic singlet-doublet system is calculated using a diagrammatic high density expansion technique. The lowest order diagrams, which correspond to the random phase approximation (RPA), give a detailed description of the wave vector and temperature dependence of the four exciton modes in praseodymium in terms of a Hamiltonian including isotropic Heisenberg exchange interactions and anisotropic, dipolar-like interactions. The leading contributions to the linewidths of the excitations are obtained by extending the 1/Z expansion of the generalized susceptibility propagators one order beyond the random phase approximation. This damping corresponds to spin wave scattering on single-site fluctuations. The theoretical spectral functions are in detailed agreement with experiment

  16. The effect of lanthanum applications on drought tolerance in barley

    International Nuclear Information System (INIS)

    Buckingham, S.; Maheswaran, J.; Peverill, K.; Meehan, B.; Stokes, J.

    1998-01-01

    Full text: Glasshouse investigations carried out by the authors on both perlite and soil, have repeatedly shown that several plant species, when treated with lanthanum, retain greater amounts of moisture under water stressed conditions. Dry matter increases under water stress have been observed in some cases. Barley plants watered to 50% field capacity, and show-ing signs of water stress, yielded 18% more dry matter when treated with 5 kg/ha and 10 kg/ha of lanthanum than control plants (P<0.05). The results of these experiments suggest that increased dry matter production in crops under periods of water stress, is likely when previously treated with lanthanum. Consequently, it is conceivable that lanthanum may have potential as an agent that induces drought tolerance in grain crops, grown in low rainfall areas. Subsequent field trials using barley as a test crop at Walpeup, in the Mallee region of Victoria have shown that in a below average rainfall year, combined soil and foliar applications of lanthanum can significantly increase grain yield. This effect was not evident when barley grown on the same soil type was treated with lanthanum under above average rainfall conditions

  17. On the complexing of phosphoric acid vinyl esters with praseodymium (3) and europium (3) nitrates in acetonitrile

    International Nuclear Information System (INIS)

    Goryushko, A.G.; Gololobov, Yu.G.; Boldeskul, A.E.; Oganesyan, A.S.; Yartsev, V.G.

    1990-01-01

    By the methods of electron, IR and PMR spectroscopy interaction of vinyl esters of phosphoric acid with praseodymium (3) and europium (3) nitrates in acetonitrile solutions has been studied. It is shown that the character of metal-ligand interaction is determined by chemical nature of the ligands: for a compound of ionic structure partially covalent bond is formed, and for a compound of betaine structure the interaction has mainly dipole character. Addition of molecule with betaine structure to praseodymium nitrate causes a change in geometry of Pr 3+ close surrounding and increase in its coordination number. The possibility of formation of the complex with metal-ligand ratio equal to 1:3 is shown

  18. Lanthanum trilactate: Vibrational spectroscopic study - infrared/Raman spectroscopy

    Czech Academy of Sciences Publication Activity Database

    Švecová, M.; Novák, Vít; Bartůněk, V.; Člupek, M.

    2016-01-01

    Roč. 87, Nov (2016), s. 123-128 ISSN 0924-2031 Institutional support: RVO:61388963 Keywords : lanthanum trilactate * tris(2-hydroxypropanoato-O1,O2) * lanthanum tris[2-(hydroxy-kappa O)propanoato-kappa O] * Raman spectra * infrared spectra * DFT Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.740, year: 2016

  19. Towards diode-pumped mid-infrared praseodymium-ytterbium-doped fluoride fiber lasers

    Science.gov (United States)

    Woodward, R. I.; Hudson, D. D.; Jackson, S. D.

    2018-02-01

    We explore the potential of a new mid-infrared laser transition in praseodymium-doped fluoride fiber for emission around 3.4 μm, which can be conveniently pumped by 0.975 μm diodes via ytterbium sensitizer co-doping. Optimal cavity designs are determined through spectroscopic measurements and numerical modeling, suggesting that practical diode-pumped watt-level mid-infrared fiber sources beyond 3 μm could be achieved.

  20. Cytocompatibility of a free machining titanium alloy containing lanthanum.

    Science.gov (United States)

    Feyerabend, Frank; Siemers, Carsten; Willumeit, Regine; Rösler, Joachim

    2009-09-01

    Titanium alloys like Ti6Al4V are widely used in medical engineering. However, the mechanical and chemical properties of titanium alloys lead to poor machinability, resulting in high production costs of medical products. To improve the machinability of Ti6Al4V, 0.9% of the rare earth element lanthanum (La) was added. The microstructure, the mechanical, and the corrosion properties were determined. Lanthanum containing alloys exhibited discrete particles of cubic lanthanum. The mechanical properties and corrosion resistance were slightly decreased but are still sufficient for many applications in the field of medical engineering. In vitro experiments with mouse macrophages (RAW 264.7) and human bone-derived cells (MG-63, HBDC) were performed and revealed that macrophages showed a dose response below and above a LaCl3 concentration of 200 microM, while MG-63 and HBDC tolerated three times higher concentrations without reduction of viability. The viability of cells cultured on disks of the materials showed no differences between the reference and the lanthanum containing alloy. We therefore propose that lanthanum containing alloy appears to be a good alternative for biomedical applications, where machining of parts is necessary.

  1. High pressure structural studies on nanophase praseodymium oxide

    International Nuclear Information System (INIS)

    Saranya, L.; Chandra Shekar, N.V.; Amirthapandian, S.; Hussain, Shamima; Arulraj, A.; Sahu, P. Ch.

    2014-01-01

    The phase stability of nanocrystalline Pr 2 O 3 has been investigated under pressure by in-situ high pressure X-ray diffraction using Mao-Bell type diamond anvil cell. The ambient structure and phase of the praseodymium oxide have been resolved unambiguously using x-ray diffraction, SEM and TEM techniques. Under the action of pressure the cubic phase of the system is retained up to 15 GPa. This is unusual as other isostructural rare earth oxides show structural transformations even at lower pressures. From the best fit to the P–V data with the Murnaghan equation of state yields a bulk modulus of 171 GPa

  2. High pressure structural studies on nanophase praseodymium oxide

    Energy Technology Data Exchange (ETDEWEB)

    Saranya, L. [Jamal Mohamed College, Tiruchirapalli 620020, Tamil Nadu (India); Chandra Shekar, N.V., E-mail: chandru@igcar.gov.in [Condensed Matter Physics Division, Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102, Tamil Nadu (India); Amirthapandian, S. [Materials Physics Division, Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102, Tamil Nadu (India); Hussain, Shamima [UGC-DAE-CSR node, Kokilamedu 603103, Tamil Nadu (India); Arulraj, A.; Sahu, P. Ch. [Condensed Matter Physics Division, Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102, Tamil Nadu (India)

    2014-09-15

    The phase stability of nanocrystalline Pr{sub 2}O{sub 3} has been investigated under pressure by in-situ high pressure X-ray diffraction using Mao-Bell type diamond anvil cell. The ambient structure and phase of the praseodymium oxide have been resolved unambiguously using x-ray diffraction, SEM and TEM techniques. Under the action of pressure the cubic phase of the system is retained up to 15 GPa. This is unusual as other isostructural rare earth oxides show structural transformations even at lower pressures. From the best fit to the P–V data with the Murnaghan equation of state yields a bulk modulus of 171 GPa.

  3. Physicochemical and Electrical Properties of Praseodymium Oxides

    Directory of Open Access Journals (Sweden)

    Sergio Ferro

    2011-01-01

    Full Text Available The industrial research is continuously looking for novelties that could improve the applied processes, increasing the yields, lowering the costs, or improving the performances. In industrial electrochemistry, one more aspect is the stability of electrode materials, which is generally balanced by the catalytic activity: the higher the latter, the lower the former. A compromise has to be found, and an optimization is often the result of new ideas that completely change the way of thinking. Praseodymium-oxide-based cathodes have been proved to be quite interesting devices: the hydrogen evolution reaction is guaranteed by the presence of a noble metal (platinum and/or rhodium, while the stability and poisoning resistance seem to be strongly improved by the presence of lanthanide oxides.

  4. Polarization characteristics of composite electrodes in electrochemical cells with solid electrolytes based on CeO2 and LaGaO3

    International Nuclear Information System (INIS)

    Yaroslavtsev, I. Yu.; Kuzin, B. L.; Bronin, D. I.; Bogdanovich, N. M.

    2005-01-01

    For two types of electrochemical cells with oxygen-conducting solid electrolytes based on lanthanum gallate (LSGM) and cerium oxide (SDC) studied are the temperature dependences of the polarization conductivity of air electrodes prepared from lanthanum strontium manganite (LSM) and composites LSM-LSGM, LSM-SDC, and LSM-SSZ (SSZ is zirconium dioxide-based electrolyte). Effect of praseodymium oxide, added into these electrodes as a modifier, on their electrochemical properties is examined. Electrochemical systems with an LSM/LSGM interface exhibit low electrochemical activity toward the oxygen reaction, because during the formation of electrodes, LSM interacts with LSGM to form a poorly conducting product [ru

  5. Synthesis, Characterization and Thermal Diffusivity of Holmium and Praseodymium Zirconates

    OpenAIRE

    Stopyra M.; Niemiec D.; Moskal G.

    2016-01-01

    A2B2O7 oxides with pyrochlore or defected fluorite structure are among the most promising candidates for insulation layer material in thermal barrier coatings. The present paper presents the procedure of synthesis of holmium zirconate Ho2Zr2O7 and praseodymium zirconate Pr2Zr2O7 via Polymerized-Complex Method (PCM). Thermal analysis of precursor revealed that after calcination at relatively low temperature (700°C) fine-crystalline, single-phase material is obtained. Thermal diffusivity was me...

  6. New even and odd parity levels of neutral praseodymium

    International Nuclear Information System (INIS)

    Syed, T I; Siddiqui, I; Shamim, K; Uddin, Z; Guthöhrlein, G H; Windholz, L

    2011-01-01

    The hyperfine (hf) structure of some spectral lines of the praseodymium atom has been investigated by the laser-induced fluorescence method in a hollow cathode discharge lamp. We report the discovery of 18 new energy levels of even parity and 22 new energy levels of odd parity and their magnetic dipole hf interaction constants A. Using these newly discovered levels, 268 lines were classified by means of laser spectroscopy, 97 of them by laser excitation and 171 via laser-induced fluorescence. In addition, 23 lines, observed in a Fourier transform spectrum, were classified by means of their wavenumbers and their hf patterns.

  7. Determination of redox-active centers in praseodymium doped ceria by in situ-XANES spectroscopy

    DEFF Research Database (Denmark)

    Kiebach, Wolff-Ragnar; Chatzichristodoulou, Christodoulos; Werchmeister, Rebecka Maria Larsen

    2012-01-01

    Praseodymium doped ceria, a material of interest for electrochemical flue gas purification, was investigated with in situ X-ray Absorption Near Edge Structure spectroscopy between room temperature and 500°C in air and diluted nitrogen(II) oxide (NO/Ar) (1% NO in Ar). For temperatures above 400°C...

  8. The effective recovery of praseodymium from mixed rare earths via a hollow fiber supported liquid membrane and its mass transfer related

    International Nuclear Information System (INIS)

    Wannachod, Pharannalak; Chaturabul, Srestha; Pancharoen, Ura; Lothongkum, Anchaleeporn W.; Patthaveekongka, Weerawat

    2011-01-01

    Graphical abstract: Display Omitted Research highlights: → Maximum percentage of praseodymium extraction at 91.7% from 10% (v/v) bis (2,4,4-trimethylpentyl) phosphinic acid as extractant carrier in multi cycle operation through single HFLSM module. → Mass transfer mechanism of this system was investigated. → The rate-controlling step of this system was the diffusion of praseodymium ions through the film layer between the feed solution and the liquid membrane. → Model prediction of the dimensionless concentrations and separation factors showed promising agreement with the experimental data. - Abstract: The recovery of praseodymium from mixed rare earths via a hollow fiber supported liquid membrane (HFSLM) was examined. Bis(2,4,4-trimethylpentyl) phosphinic acid - known as Cyanex 272 - was used as an extractant carrier. The stripping solution was hydrochloric acid solution. The experiments examined in functions of the concentrations of the carrier in liquid membrane, the (initial) pH's of initial feed solution within the acidic-pH range, the concentrations of hydrochloric acid, the flow rates of feed and stripping solution, and the operation mode of runs through the hollow fiber module. In addition, the influence of circulation of the stripping solution at various numbers of runs through the HFSLM on the outlet concentration of praseodymium ions in the stripping solution was observed. Mass transfer mechanism in the system was investigated. Extraction equilibrium constant (K ex ), distribution ratio (D), permeability (P) and mass transfer coefficients were determined. The aqueous-phase mass-transfer coefficient (k i ) and organic-phase mass-transfer coefficient (k m ) were reported to 0.0103 and 0.788 cm s -1 , respectively, in which k m is much higher than the k i . Thus it suggests the rate-controlling step is the diffusion of praseodymium ions through the film layer between the feed solution and the liquid membrane. Model prediction of the dimensionless

  9. An experimental study of praseodymium intermetallic compounds at low temperatures

    International Nuclear Information System (INIS)

    Greidanus, F.J.A.M.

    1982-01-01

    In this thesis the author studies the low temperature properties of praseodymium intermetallic compounds. In chapter 2 some of the techniques used for the experiments described in the subsequent chapters are discussed. A set-up to perform specific-heat experiments below 1 K and a technique for performing magnetic susceptibility measurments below 1 K, using a superconducting quantum interference device (SQUID) are described. Chapter 3 is devoted to the theory of interacting Pr 3+ ions. Both bilinear and biquadratic interactions are dealt with in a molecular-field approximation. It is shown that first as well as second-order phase transitions can occur, depending on the nature of the ground state, and on the ratio of magnetic to crystal-field interactions. In chapters 4, 5, 6 and 7 experimental results on the cubic Laves phase compounds PrRh 2 , PrIr 2 , PrPt 2 , PrRu 2 and PrNi 2 are presented. From inelastic neutron scattering experiments the crystalline electric field parameters of the above compounds are determined. In chapters 5 and 6 susceptibility, neutron-diffraction, hyperfine specific-heat, low-field magnetization, pulsed-field magnetization, specific-heat and resistivity measurements are presented. In chapter 7 the specific heat and differential susceptibility of PrNi 2 below 1 K are studied. Finally, in chapter 8 praseodymium intermetallic compounds with low-symmetry singlet ground states, and cubic compounds with magnetic doublet ground states are studied. (Auth.)

  10. Bio-accumulation of lanthanum from lanthanum modified bentonite treatments in lake restoration

    NARCIS (Netherlands)

    Waajen, G.; Van Oosterhout, F.; Lürling, M.

    2017-01-01

    Abstract Lanthanum (La) modified bentonite (LMB) is one of the available mitigating agents used for the reduction of the phosphorus (P) recycling in eutrophic lakes. The potential toxicity of the La from LMB to aquatic organisms is a matter of concern. In this study the accumulation of La was

  11. Thermoluminescent coactivated rare earth oxyhalide phosphors and x-ray image converters utilizing said phosphors

    International Nuclear Information System (INIS)

    Rabatin, J.G.

    1984-01-01

    Oxyhalides of lanthanum, gadolinium and lutetium coactivated with a first activator selected from bismuth and samarium to provide the color of light emission and a second coactivator (e.g. terbium or praseodymium) which increases the amount of stored energy in a stored radiographic latent image are found to be superior in their conversion efficiency of x-rays to visible light. (author)

  12. Electrochemical reduction of lanthanum trichloride in a molten equimolar mixture of sodium and potassium chlorides

    Energy Technology Data Exchange (ETDEWEB)

    Glagolevskaya, A.L.; Kuznetsov, S.A.; Polyakov, E.G.; Stangrit, P.T.

    1987-09-20

    The authors used linear voltamperometry for the investigation of the mechanism for the cathodic reduction of lanthanum. The mechanism for the cathodic reduction of lanthanum chloride in molten equimolar NaCl-KCl may be seen as consisting of a slow irreversible electrode reaction with a subsequent rapid irreversible chemical reaction. Lanthanum ions in a lower oxidation state were not found upon the prolonged maintenance of metallic lanthanum in molten NaCl-KCl-LaCl/sub 3/. Only an increase in the concentration of lanthanum(III) chloride in the melt was noted. The appearance of oxygen anions in the melt does not lead to a change in the mechanism of the cathodic reduction of lanthanum chloride but reduces the concentration of this chloride due to the formation of lanthanum oxochloride which is insoluble in the melt.

  13. Silica doped with lanthanum sol–gel thin films for corrosion protection

    International Nuclear Information System (INIS)

    Abuín, M.; Serrano, A.; Llopis, J.; García, M.A.; Carmona, N.

    2012-01-01

    We present here anticorrosive silica coatings doped with lanthanum ions for the protection of metallic surfaces as an alternative to chromate (VI)-based conversion coatings. The coatings were synthesized by the sol–gel method starting from silicon alkoxides and two different lanthanum precursors: La (III) acetate hydrate and La (III) isopropoxide. Artificial corrosion tests in acid and alkaline media showed their effectiveness for the corrosion protection of AA2024 aluminum alloy sheets for coating prepared with both precursors. The X-ray absorption Near Edge Structure and X-ray Absorption Fine Structure analysis of the coatings confirmed the key role of lanthanum in the structural properties of the coating determining its anticorrosive properties. - Highlights: ► Silica sol–gel films doped with lanthanum ions were synthesized. ► Films from lanthanum-acetate and La-alkoxide were prepared for comparison purposes. ► La-acetate is an affordable chemical reactive preferred for the industry. ► Films properties were explored by scanning electron microscopy and X-Ray absorption spectroscopy. ► An alternative to anticorrosive pre-treatments for metallic surfaces is suggested.

  14. LANTHANUM STAINING OF THE SURFACE COAT OF CELLS

    Science.gov (United States)

    Shea, Stephen M.

    1971-01-01

    Among the techniques which have been reported to stain the surface coat of cells, for electron microscopy, is lanthanum staining en bloc. Similarly, the presence of the cationic dye, Alcian blue 8GX, in a primary glutaraldehyde fixative has been reported to improve the preservation of the surface coat of cells of many types; however, the preserved coat is not very electron opaque unless thin sections are counterstained. The present paper shows that for several rat tissues lanthanum staining en bloc is an effective electron stain for the cell surface, giving excellent contrast, if combined sequentially with prefixation in an aldehyde fixative containing Alcian blue. The cationic substance cetylpyridinium chloride was found to have a similar effect to that of Alcian blue in enhancing the lanthanum staining of the surface coat material of the brush border of intestinal epithelial cells. The patterns of lanthanum staining obtained for the tissues studied strikingly resemble those reported in the literature where tissues are stained by several standard methods for demonstrating mucosubstances at the ultrastructural level. This fact and the reproduction of the effect of Alcian blue by cetylpyridinium chloride constitute a persuasive empirical argument that the material visualized is a mucopolysaccharide or mucopolysaccharide-protein complex. PMID:4108476

  15. Determination of main components in lanthanum titanates blend

    International Nuclear Information System (INIS)

    Sizonenko, T.N.; Timchenko, A.K.

    1981-01-01

    Conditions for complexonometric determination of lanthanum in the presence of titanium using the disguising of the latter are studied. A method is suggested for lanthanum and titanium determination in a blend of lanthanum titanate which is used to grow monocrystals. Sulfosalicylic acid is chosen as a disguising agent. La has been determined by complexonometric titration using EDTA with xylenol orange in urotropin. The total contents of La and Ti have been determined by titration of EDTA excess with standard solution of zinc sulfate. Ti content has been calculated from the difference between the first two determinations. Reproducibility of Ti and La determination in the blend (n=21) is characterized by the following: at 19.73% La and 57.21% Ti there are (19.72+-0.16)% La and (57.10+-0.22)% Ti, Sr equals 0.0071 and 0.0034, respectively

  16. First principle study of structural, electronic and fermi surface properties of aluminum praseodymium

    Science.gov (United States)

    Shugani, Mani; Aynyas, Mahendra; Sanyal, S. P.

    2018-05-01

    We present a structural, Electronic and Fermi surface properties of Aluminum Praseodymium (AlPr) using First-principles density functional calculation by using full potential linearized augmented plane wave (FP-LAPW) method within generalized gradient approximation (GGA). The ground state properties along with electronic and Fermi surface properties are studied. It is found that AlPr is metallic and the bonding between Al and Pr is covalent.

  17. Evolution of the local environment of lanthanum during simplified SON68 glass leaching

    International Nuclear Information System (INIS)

    Jollivet, P.; Delaye, J.M.; Den Auwer, C.; Simoni, E.

    2007-01-01

    The evolution of the short- and medium-range local environment of lanthanum was determined by L-III-edge X-ray absorption spectroscopy (XAS) during leaching of simplified SON68-type glasses. In glass without phosphorus, lanthanum is found in a silicate environment, and its first coordination sphere comprises eight oxygen atoms at a mean distance of 2.51 angstrom. When this glass was leached at a high renewal rate, the lanthanum local environment was significantly modified: it was present at hydroxy-carbonate and silicate sites with a mean La-O distance of 2.56 angstrom, and the second neighbors consisted of La atoms instead of Si for the glass. Conversely, in the gel formed at low renewal rates, lanthanum was found in a silicate environment similar to that of the glass. In phosphorus-doped glass, lanthanum is found in a phosphate environment, although the Si/P atomic ratio is 20:1. Lanthanum is surrounded by seven oxygen atoms at a mean distance of 2.37 angstrom. When phosphorus-doped glass is leached, regardless of the leaching solution flow rate, the short- and medium-range lanthanum local environment remains almost constant; the most significant change is a 0.05 angstrom increase in the La-O distance. (authors)

  18. Calcium and lanthanum solid base catalysts for transesterification

    Science.gov (United States)

    Ng, K. Y. Simon; Yan, Shuli; Salley, Steven O.

    2015-07-28

    In one aspect, a heterogeneous catalyst comprises calcium hydroxide and lanthanum hydroxide, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g. In another aspect, a heterogeneous catalyst comprises a calcium compound and a lanthanum compound, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g, and a total basicity of about 13.6 mmol/g. In further another aspect, a heterogeneous catalyst comprises calcium oxide and lanthanum oxide, wherein the catalyst has a specific surface area of more than about 10 m.sup.2/g. In still another aspect, a process for preparing a catalyst comprises introducing a base precipitant, a neutral precipitant, and an acid precipitant to a solution comprising a first metal ion and a second metal ion to form a precipitate. The process further comprises calcining the precipitate to provide the catalyst.

  19. Silica doped with lanthanum sol-gel thin films for corrosion protection

    Energy Technology Data Exchange (ETDEWEB)

    Abuin, M. [Department of Materials Physics, Complutense University at Madrid, Avda. Complutense sn, 28004 Madrid (Spain); Serrano, A. [Glass and Ceramic Institute, CSIC, C. Kelsen 5, 28049 Madrid (Spain); Llopis, J. [Department of Materials Physics, Complutense University at Madrid, Avda. Complutense sn, 28004 Madrid (Spain); Garcia, M.A. [Glass and Ceramic Institute, CSIC, C. Kelsen 5, 28049 Madrid (Spain); IMDEA Nanoscience, Fco. Tomas y Valiente 7, 28049 Madrid (Spain); Carmona, N., E-mail: n.carmona@fis.ucm.es [Department of Materials Physics, Complutense University at Madrid, Avda. Complutense sn, 28004 Madrid (Spain)

    2012-06-01

    We present here anticorrosive silica coatings doped with lanthanum ions for the protection of metallic surfaces as an alternative to chromate (VI)-based conversion coatings. The coatings were synthesized by the sol-gel method starting from silicon alkoxides and two different lanthanum precursors: La (III) acetate hydrate and La (III) isopropoxide. Artificial corrosion tests in acid and alkaline media showed their effectiveness for the corrosion protection of AA2024 aluminum alloy sheets for coating prepared with both precursors. The X-ray absorption Near Edge Structure and X-ray Absorption Fine Structure analysis of the coatings confirmed the key role of lanthanum in the structural properties of the coating determining its anticorrosive properties. - Highlights: Black-Right-Pointing-Pointer Silica sol-gel films doped with lanthanum ions were synthesized. Black-Right-Pointing-Pointer Films from lanthanum-acetate and La-alkoxide were prepared for comparison purposes. Black-Right-Pointing-Pointer La-acetate is an affordable chemical reactive preferred for the industry. Black-Right-Pointing-Pointer Films properties were explored by scanning electron microscopy and X-Ray absorption spectroscopy. Black-Right-Pointing-Pointer An alternative to anticorrosive pre-treatments for metallic surfaces is suggested.

  20. The evolution mechanism of the dislocation loops in irradiated lanthanum doped cerium oxide

    International Nuclear Information System (INIS)

    Miao, Yinbin; Aidhy, Dilpuneet; Chen, Wei-Ying; Mo, Kun; Oaks, Aaron; Wolf, Dieter; Stubbins, James F.

    2014-01-01

    Cerium dioxide, a non-radioactive surrogate of uranium dioxide, is useful for simulating the radiation responses of uranium dioxide and mixed oxide fuel (MOX). Controlled additions of lanthanum can also be used to form various levels of lattice oxide or anion vacancies. In previous transmission electron microscopy (TEM) experimental studies, the growth rate of dislocation loops in irradiated lanthanum doped ceria was reported to vary with lanthanum concentration. This work reports findings of the evolution mechanisms of the dislocation loops in cerium oxide with and without lanthanum dopants based on a combination of molecular statics and molecular dynamics simulations. These dislocation loops are found to be b=1/3〈111〉 interstitial type Frank loops. Calculations of the defect energy profiles of the dislocation loops with different structural configurations and radii reveal the basis for preference of nucleation as well as the driving force of growth. Frenkel pair evolution simulations and displacement cascade overlaps simulations were conducted for a variety of lanthanum doping conditions. The nucleation and growth processes of the Frank loop were found to be controlled by the mobility of cation interstitials, which is significantly influenced by the lanthanum doping concentration. Competition mechanisms coupled with the mobility of cation point defects were discovered, and can be used to explain the lanthanum effects observed in experiments

  1. DISSOLUTION OF LANTHANUM FLUORIDE PRECIPITATES

    Science.gov (United States)

    Fries, B.A.

    1959-11-10

    A plutonium separatory ore concentration procedure involving the use of a fluoride type of carrier is presented. An improvement is given in the derivation step in the process for plutonium recovery by carrier precipitation of plutonium values from solution with a lanthanum fluoride carrier precipitate and subsequent derivation from the resulting plutonium bearing carrier precipitate of an aqueous acidic plutonium-containing solution. The carrier precipitate is contacted with a concentrated aqueous solution of potassium carbonate to effect dissolution therein of at least a part of the precipitate, including the plutonium values. Any remaining precipitate is separated from the resulting solution and dissolves in an aqueous solution containing at least 20% by weight of potassium carbonate. The reacting solutions are combined, and an alkali metal hydroxide added to a concentration of at least 2N to precipitate lanthanum hydroxide concomitantly carrying plutonium values.

  2. Adsorption of lithium-lanthanum films on W (112) face

    International Nuclear Information System (INIS)

    Gupalo, M.S.; Smereka, T.P.; Palyukh, B.M.; Babkin, G.V.

    1986-01-01

    The method of contact potential difference is employed to study the electron adsorption properties (the work function phi and adsorption heat q) lithium films on a lanthanized W(112) surface. It is found that the work function of mixed lithium-lanthanum films is intermediate between phi of the summands. The presence of lanthanum on a W(112) face reduces the adsorption heat of lithium

  3. Electrical properties of praseodymium oxide doped Boro-Tellurite glasses

    Science.gov (United States)

    Jagadeesha Gowda G., V.; Devaraja, C.; Eraiah, B.

    2016-05-01

    Glasses of the composition xPr6O11- (35-x)TeO2-65B2O3 (x=0, 0.1 to 0.5 mol %) have been prepared using the melt quenching method. The ac and dc conductivity of glass have been measured over a wide range of frequencies and temperatures. Experimental results indicate that the ac conductivity depend on temperature, frequency and Praseodymium content. The conductivity as a function of frequency exhibited two components: dc conductivity (σdc), and ac conductivity (σac). The activation energies are estimated and found to be decreases with composition. The impedance plot at each temperature appeared as a semicircle passes through the origin.

  4. Nanosized lead lanthanum titanate (PLT) ceramic powders synthesized by the oxidant peroxo method

    Energy Technology Data Exchange (ETDEWEB)

    Camargo, Emerson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil)], E-mail: camargo@ufscar.br; Barrado, Cristiano M. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil); Ribeiro, Caue [EMBRAPA Instrumentacao Agropecuaria, Rua XV de Novembro 1452, Sao Carlos SP 13560-970 (Brazil)], E-mail: caue@cnpdia.embrapa.br; Longo, Elson [Department of Biochemistry, Chemistry Institute of Araraquara, UNESP-Sao Paulo State University, Rua Francisco Degni, CP 355, Araraquara SP 14801-907 (Brazil)], E-mail: elson@iq.unesp.br; Leite, Edson R. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod.Washingtin Luis km 235, CP 676, Sao Carlos SP 13565-9905 (Brazil)], E-mail: derl@power.ufscar.br

    2009-05-05

    For the first time it is reported the synthesis of lead titanate modified with rare earth by the oxidant-peroxo method (OPM). Lanthanum was added up to 20% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of a solution of lead and lanthanum nitrate into an aqueous solution of titanium peroxo complexes. The amorphous precipitate formed was heat-treated at different temperatures in the range from 400 to 900 deg. C for crystallization. Powders were characterized by Raman spectroscopy and X-ray diffraction. Tetragonal perovskite structure was observed for the samples up to 15% of lanthanum substitution and cubic perovskite for sample with 20% of lanthanum. Crystallographic domains calculated by Scherrer equation showing a probable suppression of the crystallite growth in function of lanthanum content. It was observed shifting to lower frequencies of Raman modes in the range between 100 and 400 cm{sup -1} and the vanishing of the A1(2TO) and E(1LO) modes could be attributed to transition phase from tetragonal to cubic. Electronic microscopy image revealed that the powders annealed at height temperature are spherical with sharp size distribution.

  5. Nanosized lead lanthanum titanate (PLT) ceramic powders synthesized by the oxidant peroxo method

    International Nuclear Information System (INIS)

    Camargo, Emerson R.; Barrado, Cristiano M.; Ribeiro, Caue; Longo, Elson; Leite, Edson R.

    2009-01-01

    For the first time it is reported the synthesis of lead titanate modified with rare earth by the oxidant-peroxo method (OPM). Lanthanum was added up to 20% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of a solution of lead and lanthanum nitrate into an aqueous solution of titanium peroxo complexes. The amorphous precipitate formed was heat-treated at different temperatures in the range from 400 to 900 deg. C for crystallization. Powders were characterized by Raman spectroscopy and X-ray diffraction. Tetragonal perovskite structure was observed for the samples up to 15% of lanthanum substitution and cubic perovskite for sample with 20% of lanthanum. Crystallographic domains calculated by Scherrer equation showing a probable suppression of the crystallite growth in function of lanthanum content. It was observed shifting to lower frequencies of Raman modes in the range between 100 and 400 cm -1 and the vanishing of the A1(2TO) and E(1LO) modes could be attributed to transition phase from tetragonal to cubic. Electronic microscopy image revealed that the powders annealed at height temperature are spherical with sharp size distribution.

  6. Distribution of lanthanum and neodymium in Di(2-ethlhexyl) phosphoric acid and tributylphosphate

    International Nuclear Information System (INIS)

    Kraikaew, J.; Suparith, N.; Pruantonsai, P.

    1994-01-01

    Lanthanum and neodymium are among the high quantity elements in mixed rare earth from monazite processing. The popular rare earth separation process is liquid-liquid extraction. This research was carried out to study lanthanum and neodymium distribution in two extractants, di(2-ethylhexyl) phosphoric acid and tributylphosphate. The experimental results show that neodymium distributes in both extractants better than lanthanum. The distribution of both elements are higher at low acidity than at high acidity. Quick and rough investigation by calculating the ratio of distribution coefficient of neodymium to lanthanum in each extractant indicated that La-nd separation efficiency of Di(2-ethylhexyl) phosphoric acid is higher than that of tributylphosphate

  7. Pressure behaviour of the superconducting transition temperature of lanthanum

    International Nuclear Information System (INIS)

    Glocker, R.

    1977-01-01

    The dissertation has the following chapters: 1) Introduction, 2) Fundamentals of the microscopic theory of superconductivity, 3) Calculation of the first momentum of the Eliashberg function, 4) Determination of the average values of frequency, 5) The relativistic cellular method and its application to lanthanum, 6) Results of the calculation of the electron-phonon coupling cosntants for f.c.c. lanthanum, 7) Phonon dispersion and phonon state density. (orig.) [de

  8. Functionalization of lanthanum hydroxide nanowires by atom transfer radical polymerization

    International Nuclear Information System (INIS)

    Zhou Mi; Yuan Jinying; Yuan Weizhong; Yin Yingwu; Hong Xiaoyin

    2007-01-01

    Atom transfer radical polymerization (ATRP) has been used to prepare a core-shell hybrid nanostructure successfully: a hard core of single-crystalline lanthanum hydroxide nanowires and a soft shell of polystyrene (PS) brushes. Transmission electron microscopy (TEM) images indicated that the resulting products presented special structures and different thicknesses of polymer layers. The chemical components and grafted PS quantities of the samples were measured by Fourier transform infrared (FT-IR) spectroscopy and thermogravimetric analysis (TGA). The polymers showed narrow polydispersity, which proved that the lanthanum hydroxide nanowires initiated the 'living'/controlled polymerization of styrene. With the modifiability of lanthanum hydroxide nanowires, the solubility increased, which affords a new way to functionalize nanowires

  9. A neutron polarisation analysis study of the 'central' peak in single-crystal praseodymium

    International Nuclear Information System (INIS)

    Burke, S.K.; Stirling, W.G.; McEwen, K.A.; Salford Univ.

    1981-01-01

    The technique of neutron polarisation analysis has been used to examine the broad 'central' peak in paramagnetic praseodymium. Measurements over the temperature range 1.2-25 K show that these peaks, observed at reciprocal space positions (Q 1 , 0, 2m + 1) with Q 1 = 0.11 tau 100 , are entirely magnetic in character. The relationship between these short-range magnetic correlations and the long-range antiferromagnetic ordering process is discussed. (author)

  10. Spectrophotometric study of the complexation equilibria of lanthanum(III) with 1,4-bis(4'-methylanilino)anthraquinone and the determination of lanthanum(III)

    International Nuclear Information System (INIS)

    Idriss, K.A.-R; El-Shahawy, A.S.; Sedaira, H.; Harfoush, A.A.

    1985-01-01

    The complexation equilibria of lanthanum(III) with 1,4-bis(4'-methylanilino)anthraquinone (Quinizarin Green) were studied spectrophotometrically in 40% V/V dimethylformamide using graphical analysis of the absorbance curves. The reaction mechanism of lanthanum with the bisarylaminoanthraquinone dye within the pH range 6 to 9.25 was demonstrated. The thermodynamic stabilities and the molar absorptivities of the complexes formed were determined. The optimum conditions for the spectrophotometric determination of La(III) with this reagent were found. (author)

  11. Fabrication of mesoporous and high specific surface area lanthanum carbide-carbon nanotube composites

    International Nuclear Information System (INIS)

    Biasetto, L.; Carturan, S.; Maggioni, G.; Zanonato, P.; Bernardo, P. Di; Colombo, P.; Andrighetto, A.; Prete, G.

    2009-01-01

    Mesoporous lanthanum carbide-carbon nanotube composites were produced by means of carbothermal reaction of lanthanum oxide, graphite and multi-walled carbon nanotube mixtures under high vacuum. Residual gas analysis revealed the higher reactivity of lanthanum oxide towards carbon nanotubes compared to graphite. After sintering, the composites revealed a specific surface area increasing with the amount of carbon nanotubes introduced. The meso-porosity of carbon nanotubes was maintained after thermal treatment.

  12. Liquid praseodymium heat content by levitation calorimetry. [Sample size 0. 5 - 1. 5g; 1460 to 2289/sup 0/K

    Energy Technology Data Exchange (ETDEWEB)

    Stretz, L.A.; Bautista, R.G.

    1976-01-01

    The high-temperature heat content of liquid praseodymium was measured experimentally by the levitation calorimetry technique. The samples, ranging in size from 0.5 to 1.5 g, were simultaneously levitated and heated by a radiofrequency generator in an argon-helium mixture prior to being dropped into a conventional copper block drop calorimeter. Corrections were made for the convection and radiation losses during the fall of the sample from the levitation chamber into the calorimeter. The praseodymium data, from 1460 to 2289K, were fitted by the following equation where the indicated errors represent the average deviation of the experimental value from the value predicted by the equation: H/sub T/ - H/sub 298/./sub 15/ = (41.57 +- 0.29) (T - 1208) + (41733 +- 197) J/mol. (auth)

  13. Effects of the wet air on the properties of the lanthanum oxide and lanthanum aluminate thin films

    International Nuclear Information System (INIS)

    Jun, Jin Hyung; Choi, Doo Jin

    2006-01-01

    Lanthanum oxide and lanthanum aluminate thin films were deposited on Si substrates. The as-grown films were stored in wet ambient and dry ambient for days and annealed after storage and also the structural and the electrical properties of the films were investigated. As the storage time increased, the La 2 O 3 films stored in wet ambient showed rapid reaction with moisture and the properties degraded. In case of the LAO films, although the thickness of the film also increased during hydration, the properties of the film did not so much changed due to the role of the incorporated aluminum. The LAO films showed better hydration resistance characteristics and so more suitable for conventional wet cleaning process in semiconductor fabrication

  14. Improvement of acid and base resistance of nickel phosphate pigment by the addition of lanthanum cation

    International Nuclear Information System (INIS)

    Onoda, Hiroaki; Matsui, Hironori; Tanaka, Isao

    2007-01-01

    Transition metal phosphates are used as inorganic pigments, however these materials had a weak point for acid and base resistance. Because lanthanum phosphate is insoluble in acidic and basic solution, the addition of lanthanum cation was tried for the improvement of the acid and base resistance of nickel phosphate pigment. The lanthanum-doped nickel phosphates were prepared from phosphoric acid, nickel nitrate, and lanthanum nitrate solution. The additional effects of lanthanum cation were studied on the chemical composition, particle shape and size distribution, specific surface area, color, acid and base resistance of the precipitations and their thermal products

  15. Analyzing relation between the radioactivity in lanthanum products and the origins of RE chlorides

    International Nuclear Information System (INIS)

    Wan Rongsheng

    2004-01-01

    Objective: To analyze the relation between the radioactivity in Lanthanum products and the origins of RE Chlorides. Methods: Using JY-38 plus sequential ICP spectrometer to examine the content of the uranium in the RE Chlorides. Using FJ-2603 low background alpha, beta measurement apparatus to measure total alpha and total beta activities of Lanthanum products. Results: The content of the uranium in the RE Chlorides is much lower in Baotou's than Hunan's. The radioactivity in Lanthanum products are made from the RE Chlorides of Baotou is much lower than that in Hunan's too. The radioactivity in Lanthanum products depends on the origins of RE Chlorides. Conclusion: The basic data were provided for radioactivity in Lanthanum products which are made from RE Chlorides of different places of China. The mathematical model was founded for the reasonable use of resource RE Chlorides

  16. Microwave-assisted synthesis of lanthanum conversion coating on Mg-Li alloy and its corrosion resistance

    International Nuclear Information System (INIS)

    Song Dalei; Jing Xiaoyan; Wang Jun; Lu Shanshan; Yang Piaoping; Wang Yanli; Zhang Milin

    2011-01-01

    Graphical abstract: Highlights: → The method of microwave is used to synthesize lanthanum conversion coating. → Lanthanum conversion coating on Mg-Li alloy was studied. → Different conditions between room temperature and microwave were compared. → The corrosion behavior of lanthanum conversion coatings was studied. → The corrosion mechanism of lanthanum conversion coatings was studied. - Abstract: Lanthanum-based conversion coating on Mg-Li alloy has been prepared by a microwave-assisted method. X-ray diffractions (XRD) indicate that the intermetallic compounds of lanthanum are formed on Mg-Li alloy surface. Scanning electron microscopy (SEM) images show that the coating has different morphologies and special structures. The corrosion resistance was assessed by means of potentiodynamic polarization curves and electrochemical impedance spectra (EIS). The results indicate that this coating significantly reduces the corrosion rate of Mg-Li alloy in NaCl solution. A comparing experiment indicates that the coating prepared by microwave-assisted process has superior corrosion resistance to the coating obtained at room temperature.

  17. Electrical conductivity studies of nanocrystalline lanthanum silicate synthesized by sol-gel route

    International Nuclear Information System (INIS)

    Nallamuthu, N.; Prakash, I.; Satyanarayana, N.; Venkateswarlu, M.

    2011-01-01

    Research highlights: → Nanocrystalline La 10 Si 6 O 27 material was synthesized by sol-gel method. → TG/DTA curves predicted the thermal behavior of the material. → FTIR spectra confirmed the formation of SiO 4 and La-O network in the La 10 Si 6 O 27 . → XRD patterns confirmed the formation of pure crystalline La 10 Si 6 O 27 phase. → The grain interior and the grain boundary conductivities are evaluated. - Abstract: Nanocrystalline apatite type structured lanthanum silicate (La 10 Si 6 O 27 ) sample was synthesized by sol-gel process. Thermal behavior of the dried gel of lanthanum silicate sample was studied using TG/DTA. The structural coordination of the dried gel of lanthanum silicate, calcined at various temperatures, was identified from the observed FTIR spectral results. The observed XRD patterns of the calcined dried gel were compared with the ICDD data and confirmed the formation of crystalline lanthanum silicate phase. The average crystalline size of La 10 Si 6 O 27 was calculated using the Scherrer formula and it is found to be ∼80 nm. The observed SEM images of the lanthanum silicate indicate the formation of the spherical particles and the existence of O, Si and La in the lanthanum silicate are confirmed from the SEM-EDX spectrum. The grain and grain boundary conductivities are evaluated by analyzing the measured impedance data, using winfit software, obtained at different temperatures, of La 10 Si 6 O 27 sample. Also, the observed grain and grain boundary conductivity behaviors of the La 10 Si 6 O 27 sample are analysed using brick layer model. The electrical permittivity and electrical modulus were calculated from the measured impedance data and were analyzed by fitting through the Havriliak and Negami function to describe the dielectric relaxation behavior of the nanocrystalline lanthanum silicate.

  18. Management of hyperphosphatemia in patients with end-stage renal disease: focus on lanthanum carbonate

    Directory of Open Access Journals (Sweden)

    Veerle P Persy

    2009-04-01

    Full Text Available Veerle P Persy, Geert J Behets, Marc E De Broe, Patrick C D’HaeseLaboratory of Pathophysiology, University of Antwerp, BelgiumAbstract: Elevated serum phosphate levels as a consequence of chronic kidney disease (CKD contribute to the increased cardiovascular risk observed in dialysis patients. Protein restriction and dialysis fail to adequately prevent hyperphosphatemia, and in general treatment with oral phosphate binding agents is necessary in patients with advanced CKD. Phosphate plays a pivotal role in the development of vascular calcification, one of the factors contributing to increased cardiovascular risk in CKD patients. Treatment of hyperphosphatemia with standard calcium-based phosphate binders and vitamin D compounds can induce hypercalcemic episodes, increase the Ca × PO4 product and thus add to the risk of ectopic mineralization. In this review, recent clinical as well as experimental data on lanthanum carbonate, a novel, non-calcium, non-resin phosphate binding agent are summarized. Although lanthanum is a metal cation no aluminium-like toxicity is observed since the bioavailability of lanthanum is extremely low and its metabolism differs from that of aluminium. Clinical studies now document the absence of toxic effects of lanthanum for up to 6 years of follow-up. The effects of lanthanum on bone, vasculature and brain are discussed and put in perspective with lanthanum pharmacokinetics.Keywords: lanthanum carbonate, phosphate binding, chronic kidney disease

  19. Electrical properties of praseodymium oxide doped Boro-Tellurite glasses

    Energy Technology Data Exchange (ETDEWEB)

    Jagadeesha Gowda, G.V. [Dept. of Physics, Sapthagiri College of Engineering, Bengaluru,India.Email:jagadeeshphy@rediffmail.com (India); Devaraja, C. [Dept.of Physics, Nagarjuna college of engineering and Technology, Bengaluru. India Email: deva.drr@rediffmail.com (India); Eraiah, B. [Dept.of Physics, Bangalore University, Bengaluru,India.Email:eraiah@rediffmail.com (India)

    2016-05-06

    Glasses of the composition xPr{sub 6}O{sub 11}- (35-x)TeO{sub 2}-65B{sub 2}O{sub 3} (x=0, 0.1 to 0.5 mol %) have been prepared using the melt quenching method. The ac and dc conductivity of glass have been measured over a wide range of frequencies and temperatures. Experimental results indicate that the ac conductivity depend on temperature, frequency and Praseodymium content. The conductivity as a function of frequency exhibited two components: dc conductivity (σ{sub dc}), and ac conductivity (σ{sub ac}). The activation energies are estimated and found to be decreases with composition. The impedance plot at each temperature appeared as a semicircle passes through the origin.

  20. Addition compounds between lanthanide trifluoromethane sulphonates and N,N,N',N' - tetrametilmalonamida (TMMA)

    International Nuclear Information System (INIS)

    Bellis, V.M. de.

    1984-01-01

    The preparation and characterization of the addiction compounds between lanthanide trifluoromethanesulphonates with the N,N,N',N' - tetramethylmodomamide (TMMA) are reported. The characterization of the compounds obtained by microanalytical procedures, infrared spectra, conductance measurements, X-ray powder patterns, absorption spectra of the praseodymium, neodymium, holmium and erbium and the emission spectra of the europium and the europium-doped lanthanum and lutetium adducts were made. (M.J.C.) [pt

  1. Study of behaviour of lanthanum- and yttrium electrodes in chloride melts

    International Nuclear Information System (INIS)

    Shkol'nikov, S.I.; Tolypin, E.S.; Yur'ev, B.P.

    1984-01-01

    A study was made on the lanthanum- and yttrium behaviour in a mixture of molten potassium- and sodium chlorides at various temperatures. It is shown that the lanthanum- and yttrium behaviour in KCl-NaCl melt is similar to the behaviour of other metals. Their corrosion rate is much higher as compared to other metals and it grows rapidly with increasing melt temperature. The temperature growth by 200 deg C results in an increase in the corrosion rate almost by an order. The potentials of lanthanum- and yttrium electrodes at the instant they are immersed in the melt have more negative values than the potentials of alkali metals under similar conditions

  2. Collinear laser spectroscopy on radioactive praseodymium ions and cadmium ions

    International Nuclear Information System (INIS)

    Froemmgen, Nadja

    2013-01-01

    Collinear laser spectroscopy is a tool for the model independent determination of spins, charge radii and electromagnetic moments of nuclei in ground and long-lived isomeric states. In the context of this thesis a new offline ion source for high evaporating temperatures and an ion beam analysis system were implemented at the TRIGA-LASER Experiment at the Institute for Nuclear Chemistry at the University of Mainz. The main part of the thesis deals with the determination of the properties of radioactive praseodymium and cadmium isotopes by collinear laser spectroscopy at ISOLDE/CERN. The necessary test measurements for the spectroscopy of praseodymium ions have been conducted with the aforementioned offline ion source at the TRIGA-LASER experiment. The spectroscopy of the praseodymium ions was motivated by the observation of a modulation of the electron capture decay rates of hydrogen-like 140 Pr 58+ . The nuclear magnetic moment of the nucleus is, among others, required for the explanation of the so-called GSI Oscillations and has not been studied experimentally before. Additionally, the determined electron capture decay constant of hydrogen-like 140 Pr 58+ is lower than the one of helium-like 140 Pr 57+ . The explanation of this phenomenon requires a positive magnetic moment. During the experiment at the COLLAPS apparatus the magnetic moments of the neutron-deficient isotopes 135 Pr, 136 Pr and 137 Pr could be determined for the first time. Unfortunately, due to a too low production yield the desired isotope 140 Pr could not be studied.The systematic study of cadmium isotopes was motivated by nuclear physics in the tin region. With Z=48 two protons are missing for the shell closure and the isotopes extend from the magic neutron number N=50 to the magic neutron number N=82. The extracted nuclear properties allow tests of different nuclear models in this region. In this thesis the obtained results of the spectroscopy of the cadmium isotopes 106-124,126 Cd and their

  3. Electrochemical Deposition of Lanthanum Telluride Thin Films and Nanowires

    Science.gov (United States)

    Chi, Su (Ike); Farias, Stephen; Cammarata, Robert

    2013-03-01

    Tellurium alloys are characterized by their high performance thermoelectric properties and recent research has shown nanostructured tellurium alloys display even greater performance than bulk equivalents. Increased thermoelectric efficiency of nanostructured materials have led to significant interests in developing thin film and nanowire structures. Here, we report on the first successful electrodeposition of lanthanum telluride thin films and nanowires. The electrodeposition of lanthanum telluride thin films is performed in ionic liquids at room temperature. The synthesis of nanowires involves electrodepositing lanthanum telluride arrays into anodic aluminum oxide (AAO) nanoporous membranes. These novel procedures can serve as an alternative means of simple, inexpensive and laboratory-environment friendly methods to synthesize nanostructured thermoelectric materials. The thermoelectric properties of thin films and nanowires will be presented to compare to current state-of-the-art thermoelectric materials. The morphologies and chemical compositions of the deposited films and nanowires are characterized using SEM and EDAX analysis.

  4. Properties of gallium lanthanum sulphide glass

    OpenAIRE

    Bastock, P.; Craig, C.; Khan, K.; Weatherby, E.; Yao, J.; Hewak, D.W.

    2015-01-01

    A series of gallium lanthanum sulphide (GLS) glasses has been studied in order to ascertain properties across the entire glass forming region. This is the first comprehensive study of GLS glass over a wide compositional range.

  5. Synthesis and spectroscopic characterization of some lanthanide(III nitrate complexes of ethyl 2-[2-(1-acetyl-2-oxopropylazo]-4,5-dimethyl-3-thiophenecarboxyate

    Directory of Open Access Journals (Sweden)

    CHEMPAKAM JANARDHANAN ATHIRA

    2011-02-01

    Full Text Available Ethyl 2-[2-(1-acetyl-2-oxopropylazo]-4,5-dimethyl-3-thiophenecarboxyate was synthesized by coupling diazotized ethyl 2-amino-4,5-dimethylthiophene-3-carboxylate with acetylacetone. Based on various spectral studies and elemental analysis, an intramolecularly hydrogen-bonded azo-enol structural form was assigned for the ligand. This ligand is versatile in forming a series of lanthanide(III complexes, viz., lanthanum(III, cerium(III, praseodymium(III, neodymium(III, samarium(III and gadolinium(III, which were characterized through various spectral studies, elemental analysis, magnetic susceptibility measurements, molar conductance and thermal analysis. The spectral data revealed that the ligand acted as a neutral tridentate, coordinating to the metal ion through one of the azo nitrogen atoms, the ester carbonyl and the enolic oxygen of the acetylacetone moiety, without deprotonation. Molar conductance values adequately supported their non-electrolytic nature. The ligand and lanthanum(III complex were subjected to X-ray diffraction studies. In addition, the lanthanum(III complex underwent a facile transesterification reaction on refluxing with methanol for a long period. The thermal behaviour of the lanthanum(III complex was also examined

  6. DFT Studies on Interaction between Lanthanum and Hydroxyamide

    Science.gov (United States)

    Pati, Anindita; Kundu, T. K.; Pal, Snehanshu

    2018-03-01

    Extraction and separation of individual rare earth elements has been a challenge as they are chemically very similar. Solvent extraction is the most suitable way for extraction of rare earth elements. Acidic, basic, neutral, chelating are the major classes of extractants for solvent extraction of rare earth elements. The coordination complex of chelating extractants is very selective with positively charged metal ion. Hence they are widely used. Hydroxyamide is capable of forming chelates with metal cations. In this present study interactions of hydroxyamide ligand with lanthanum have been investigated using density functional theory (DFT). Two different functional such as raB97XD and B3LYP are applied along with 6-31+G(d,p) basis set for carbon, nitrogen, hydrogen and SDD basis set for lanthanum. Stability of formed complexes has been evaluated based on calculated interaction energies and solvation energies. Frontier orbital (highest occupied molecular orbital or HOMO and lowest unoccupied molecular orbital or LUMO) energies of the molecule have also been calculated. Electronegativity, chemical hardness, chemical softness and chemical potential are also determined for these complexes to get an idea about the reactivity. From the partial charge distribution it is seen that oxygen atoms in hydroxyamide have higher negative charge. The double bonded oxygen atom present in the hydroxyamide structure has higher electron density and so it forms bond with lanthanum but the singly bonded oxygen atom in the hydroxyamide structure is weaker donor atom and so it is less available for interaction with lanthanum.

  7. Effect of Partial Substitution of Neodymium with Praseodymium on the Magnetic and Process Properties of Sintered Magnets of Type NdFeB

    Science.gov (United States)

    Dormidontov, N. A.; Dormidontov, A. G.; Lileev, A. S.; Kamynin, A. V.; Lukin, A. A.

    2017-01-01

    The effect of substitution of neodymium with praseodymium in sintered magnets of type NdFeB on their magnetic and process properties in the concentration range of [Pr] = 0 - 13 wt.% is studied. The special features of milling of the alloys, sintering processes and heat treatments in the production of magnets containing praseodymium are discussed. Hysteresis characteristics of B r ≥ 1.2 T, H cJ ≥ 1200 kA/m, H cb ≥ 880 kA/m, H k ≥ 960 kA/m, and BH max ≥ 280 kJ/m3 are obtained for magnets with composition (in wt.%) 33 Nd, 10 Pr, 1.5 (Ti + Al + Cu), 1.3 B, the remainder Fe.

  8. PMR investigation into complexes of lanthanum and lutetium with ethylenediaminediacetic acid

    International Nuclear Information System (INIS)

    Kostromina, N.A.; Novikova, L.B.

    1975-01-01

    Proton resonance spectra of ethylendiaminediacetic acid (EDDA) and EDDA mixtures with La and Lu as function of pH of solution was studied. Sequence of EDDA (A 2- ) protonation was established; cations H 3 A + and H 4 A 2+ were found; dissociation constants of above mentioned cations were determined. Formation of H 2 LnA 3+ , HLnA 2+ and LnA + complexes in EDDA-Ln (1:1) system was found. Difference in the bonds mobility of lanthanum and lutetium complexes was determined: lanthanum forms complexes with labile, lutetium with non-labile bonds. Information on complexes structure is collected. Acid dissociation constants of protonated complexes of lanthanum with EDDA were determined

  9. Studies on the promotion of nickel—alumina coprecipitated catalysts: II. Lanthanum oxide

    NARCIS (Netherlands)

    Lansink Rotgerink, H.G.J.; Paalman, R.P.A.M.; van Ommen, J.G.; Ross, J.R.H.

    1988-01-01

    Two series of lanthanum promoted nickel—alumina catalysts have been prepared by coprecipitation of the metal nitrates, using potassium carbonate. The molar ratio between nickel and the sum of aluminium and lanthanum was kept constant at 2.5 or 9.0 within each series. The calcination and reduction of

  10. Removal of Lanthanum (III) From Aqueous Solution Using Non-Living Water Hyacinth Roots

    International Nuclear Information System (INIS)

    Aly, A.; Amer, H.A.; Shawky, S.; Shawky, S.; Kandil, A.T.

    2013-01-01

    Removal of lanthanum (III) from aqueous solution using dried roots of water hyacinth (Eichhornia crassipes) has been investigated. The roots have been characterized by determining the ash percentage, the ph of the slurry, the elemental composition, the thermal gravimetric analysis, the surface area, the pore size, the zeta potential and ph of zero point charge. A surface area of 128 m 2 /g has been found and the micropore structure of the roots has been confirmed. Zeta potential and ph of zero point charge of the roots surfaces showed that they are positively charged within the ph range from 2 to 7.5. Sorption is rapid and depends on ph, weight of roots, concentration of lanthanum (III) and ionic strength. The sorption of lanthanum (III) was confirmed by scanning electron microscope, energy dispersive spectroscopy and the release of Ca +2 , Mg +2 and K +1 after sorption of lanthanum (III) have been indicated an ion exchange mechanism. Fourier transform infrared spectra indicated surface complexation mechanism, and sorption isotherms and kinetics were discussed. The roots were tested for removal of radioactive lanthanum ( 140 La) from simulated radioactive waste. Accepted June 2013.

  11. Strengthening and elongation mechanism of Lanthanum-doped Titanium-Zirconium-Molybdenum alloy

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Ping, E-mail: huping1985@126.com [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Jinduicheng Molybdenum Co., Ltd., Xi’an 710068 (China); Hu, Bo-liang; Wang, Kuai-she; Song, Rui; Yang, Fan [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Yu, Zhi-tao [Ruifulai Tungsten & Molybdenum Co., Ltd., Xi’an 721914 (China); Tan, Jiang-fei [School of Metallurgy Engineering, Xi’an University of Architecture and Technology, Xi’an 710055 (China); Cao, Wei-cheng; Liu, Dong-xin; An, Geng [Jinduicheng Molybdenum Co., Ltd., Xi’an 710068 (China); Guo, Lei [Ruifulai Tungsten & Molybdenum Co., Ltd., Xi’an 721914 (China); Yu, Hai-liang [School of Mechanical, Materials and Mechatronics Engineering, University of Wollongong, NSW 2522 (Australia)

    2016-12-15

    The microstructural contributes to understand the strengthening and elongation mechanism in Lanthanum-doped Titanium-Zirconium-Molybdenum alloy. Lanthanum oxide particles not only act as heterogeneous nucleation core, but also act as the second phase to hinder the grain growth during sintering crystallization. The molybdenum substrate formed sub-grain under the effect of second phase when the alloy rolled to plate.

  12. Leaching Kinetics of Praseodymium in Sulfuric Acid of Rare Earth Elements (REE) Slag Concentrated by Pyrometallurgy from Magnetite Ore

    International Nuclear Information System (INIS)

    Kim, Chul-Joo; Yoon, Ho-Sung; Chung, Kyung Woo; Lee, Jin-Young; Kim, Sung-Don; Shin, Shun Myung; Kim, Hyung-Seop; Cho, Jong-Tae; Kim, Ji-Hye; Lee, Eun-Ji; Lee, Se-Il; Yoo, Seung-Joon

    2015-01-01

    A leaching kinetics was conducted for the purpose of recovery of praseodymium in sulfuric acid (H 2 SO 4 ) from REE slag concentrated by the smelting reduction process in an arc furnace as a reactant. The concentration of H 2 SO 4 was fixed at an excess ratio under the condition of slurry density of 1.500 g slag/L, 0.3 mol H 2 SO 4 , and the effect of temperatures was investigated under the condition of 30 to 80 .deg. C. As a result, praseodymium oxide (Pr 6 O 1 1) existing in the slag was completely converted into praseodymium sulfate (Pr 2 (SO 4 ) 3 ·8H 2 O) after the leaching of 5 h. On the basis of the shrinking core model with a shape of sphere, the first leaching reaction was determined by chemical reaction mechanism. Generally, the solubility of pure REEs decreases with the increase of leaching temperatures in sulfuric acid, but REE slag was oppositely increased with increasing temperatures. It occurs because the ash layer included in the slag is affected as a resistance against the leaching. By using the Arrhenius expression, the apparent activation energy of the first chemical reaction was determined to be 9.195 kJmol -1 . In the second stage, the leaching rate is determined by the ash layer diffusion mechanism. The apparent activation energy of the second ash layer diffusion was determined to be 19.106 kJmol -1 . These relative low activation energy values were obtained by the existence of unreacted ash layer in the REE slag

  13. Characterization of dense lead lanthanum titanate ceramics prepared from powders synthesized by the oxidant peroxo method

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, Alexandre H. [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Souza, Flavio L., E-mail: flavio.souza@ufabc.edu.br [Centro de Ciencias Naturais e Humanas, Universidade Federal do ABC, Rua Santa Adelia 166, Bangu, Santo Andre, SP 09210-170 (Brazil); Chiquito, Adenilson J., E-mail: chiquito@df.ufscar.br [Departamento de Fisica, UFSCar-Federal University of Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Longo, Elson, E-mail: elson@iq.unesp.br [Instituto de Quimica de Araraquara, UNESP-Universidade Estadual Paulista, Rua Francisco Degni, CP 355 Araraquara, SP 14801-907 (Brazil); Leite, Edson R., E-mail: derl@power.ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil); Camargo, Emerson R., E-mail: camargo@ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Departamento de Quimica, UFSCar-Universidade Federal de Sao Carlos, Rod.Washington Luis km 235, CP 676 Sao Carlos, SP 13565-905 (Brazil)

    2010-12-01

    Nanosized powders of lead lanthanum titanate (Pb{sub 1-x}La{sub x}TiO{sub 3}) were synthesized by means of the oxidant-peroxo method (OPM). Lanthanum was added from 5 to 30% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of lead nitrate to prepare a solution of lead and lanthanum nitrates, which was dripped into an aqueous solution of titanium peroxo complexes, forming a reactive amorphous precipitate that could be crystallized by heat treatment. Crystallized powders were characterized by FT-Raman spectroscopy and X-ray powder diffraction, showing that tetragonal perovskite structure is obtained for samples up to 25% of lanthanum and cubic perovskite for samples with 30% of lanthanum. Powders containing 25 and 30% in mol of lanthanum were calcined at 700 deg. C for 2 h, and in order to determine the relative dielectric permittivity and the phase transition behaviour from ferroelectric-to-paraelectric, ceramic pellets were prepared and sintered at 1100 or 1150 deg. C for 2 h and subjected to electrical characterization. It was possible to observe that sample containing 25% in mol of La presented a normal behaviour for the phase transition, whereas the sample containing 30% in mol of La presented a diffuse phase transition and relaxor behaviour.

  14. Characterization of dense lead lanthanum titanate ceramics prepared from powders synthesized by the oxidant peroxo method

    International Nuclear Information System (INIS)

    Pinto, Alexandre H.; Souza, Flavio L.; Chiquito, Adenilson J.; Longo, Elson; Leite, Edson R.; Camargo, Emerson R.

    2010-01-01

    Nanosized powders of lead lanthanum titanate (Pb 1-x La x TiO 3 ) were synthesized by means of the oxidant-peroxo method (OPM). Lanthanum was added from 5 to 30% in mol through the dissolution of lanthanum oxide in nitric acid, followed by the addition of lead nitrate to prepare a solution of lead and lanthanum nitrates, which was dripped into an aqueous solution of titanium peroxo complexes, forming a reactive amorphous precipitate that could be crystallized by heat treatment. Crystallized powders were characterized by FT-Raman spectroscopy and X-ray powder diffraction, showing that tetragonal perovskite structure is obtained for samples up to 25% of lanthanum and cubic perovskite for samples with 30% of lanthanum. Powders containing 25 and 30% in mol of lanthanum were calcined at 700 deg. C for 2 h, and in order to determine the relative dielectric permittivity and the phase transition behaviour from ferroelectric-to-paraelectric, ceramic pellets were prepared and sintered at 1100 or 1150 deg. C for 2 h and subjected to electrical characterization. It was possible to observe that sample containing 25% in mol of La presented a normal behaviour for the phase transition, whereas the sample containing 30% in mol of La presented a diffuse phase transition and relaxor behaviour.

  15. Hyperfine structure measurements and discovery of new energy levels in neutral praseodymium

    Energy Technology Data Exchange (ETDEWEB)

    Imran, Siddiqui; Khan, Shamim; Syed, Tanweer Iqbal; Gamper, Bettina; Windholz, Laurentius [Inst. f. Experimentalphysik, Techn. Univ. Graz, Petersgasse 16, A-8010 Graz (Austria)

    2011-07-01

    We present here 14 even and 17 odd parity new energy levels of the neutral praseodymium atom. Free praseodymium atoms in ground and excited states are produced in a hollow cathode discharge lamp by cathode sputtering. The hyperfine structure (hfs) of the spectral lines is investigated by the method of laser induced fluorescence (LIF) spectroscopy. As an example of the method used we discuss briefly the finding of the new level at 27304.431 cm{sup -1}, even parity, J=9/2 and A=690(1) MHz. Laser excitation of the line at 6004.23 Aa is performed and a LIF signal is detected at fluorescence lines 5246.709, 5412.95, 5925.10, 6107.88, 6287.02, 6419.16, and 6620.63 A. The hfs is then recorded digitally and fitted to find reliable values of angular momentum J, magnetic and electric quadrupole hyperfine constants A and B for the combining fine structure levels. Assuming an unknown upper level, a lower level is searched in the data base of known levels, having the J and A values determined from the fit procedure. A level with 10654.11 cm{sup -1}, odd parity, J=7/2 and A=169(2) MHz is found. The energy of the upper level is calculated by adding the center of gravity wave number of the excited line to the energy of the lower level. The existence of the new level is checked by at least one additional laser excitation from another known lower level.

  16. Signal amplification of dopamine using lanthanum hexacyanoferrate ...

    Indian Academy of Sciences (India)

    rare earth metal hexacyanoferrates, for e.g., lanthanum ... to facilitate the electrochemical reactions of biological molecules.9,10 In general ... bic acid and potassium hexacyanoferrate (Merck) were ... were prepared using doubly distilled water.

  17. Leaching behavior of lanthanum, nickel and iron from spent catalyst using inorganic acids

    Science.gov (United States)

    Astuti, W.; Prilitasari, N. M.; Iskandar, Y.; Bratakusuma, D.; Petrus, H. T. B. M.

    2018-01-01

    Highly technological applications of rare earth metals (REs) and scarcity of supply have become an incentive torecover the REs from various resources, which include high grade and low grade ores, as well as recycledwaste materials. Spent hydrocracking catalyst contain lanthanum and a variety of valuable metals such as nickel and iron. This study investigated the recovery of lanthanum, nickel and iron from spent hydrocracking catalyst by leaching using various inorganic acid (sulfuric acid, hydrochloric acid, and nitric acid). The effect of acid concentration, type of acid and leaching temperature was conducted to study the leaching behavior of each valuable metal from spent-catalyst. It has been shown that it is possible to recover more than 90% of lanthanum, however the leaching efficiency of nickel and iron in this process was very low. It can be concluded that the leaching process is selective for lanthanum recovery from hydrocracking spent-catalyst.

  18. Structural and dielectric characterization of praseodymium-modified lead titanate ceramics synthesized by the OPM route

    Energy Technology Data Exchange (ETDEWEB)

    Pinto, Alexandre H., E-mail: alehp1@yahoo.com.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos 13565-905, SP (Brazil); Souza, Flavio L., E-mail: fleandro.ufabc@gmail.com [Centro de Ciencias Naturais e Humanas, UFABC - Universidade Federal do ABC, Santo Andre 09210-170, SP (Brazil); Longo, Elson, E-mail: elson@iq.unesp.br [Department of Biochemistry, Chemistry Institute of Araraquara, UNESP - Sao Paulo State University, Rua Francisco Degni, CP 355, Araraquara 14801-907, SP (Brazil); Leite, Edson R., E-mail: derl@power.ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos 13565-905, SP (Brazil); Camargo, Emerson R., E-mail: camargo@ufscar.br [LIEC-Laboratorio Interdisciplinar de Eletroquimica e Ceramica, Department of Chemistry, UFSCar-Federal University of Sao Carlos, Rod. Washington Luis km 235, CP 676, Sao Carlos 13565-905, SP (Brazil)

    2011-10-17

    Highlights: {yields} Highly reactive nanosized powders of Pb(0.8)Pr(0.2)TiO(3) were obtained by the OPM route. {yields} Tetragonal phase was observed by X-ray diffraction and confirmed by Raman spectroscopy. {yields} SEM images showed powders partially sintered with particles of approximately 54 nm. {yields} Dielectric measurements show a normal behavior for the ferroelectric to paraelectric transition. - Abstract: Quasi-spherical nanoparticles of praseodymium-modified lead titanate powder (Pb{sub 0.80}Pr{sub 0.20}TiO{sub 3}) with an average size of 54.8 nm were synthesized successfully by the oxidant-peroxo method (OPM) and were used to prepare highly dense ceramic bodies which were sintered at 1100 and 1150 deg. C for 2 h. A tetragonal phase was identified in the powder and ceramic samples by X-ray powder diffraction and FT-Raman spectroscopy at room temperature. The fractured surface of the ceramic sample showed a high degree of densification with fairly uniform grain sizes. Dielectric constants measured in the range of 30-300 deg. C at different frequencies (120 Hz and at 1, 10 and 100 kHz) indicated that samples with 20 mol% praseodymium showed normal ferroelectric behavior regardless of the sintering temperature.

  19. Structural and dielectric characterization of praseodymium-modified lead titanate ceramics synthesized by the OPM route

    International Nuclear Information System (INIS)

    Pinto, Alexandre H.; Souza, Flavio L.; Longo, Elson; Leite, Edson R.; Camargo, Emerson R.

    2011-01-01

    Highlights: → Highly reactive nanosized powders of Pb(0.8)Pr(0.2)TiO(3) were obtained by the OPM route. → Tetragonal phase was observed by X-ray diffraction and confirmed by Raman spectroscopy. → SEM images showed powders partially sintered with particles of approximately 54 nm. → Dielectric measurements show a normal behavior for the ferroelectric to paraelectric transition. - Abstract: Quasi-spherical nanoparticles of praseodymium-modified lead titanate powder (Pb 0.80 Pr 0.20 TiO 3 ) with an average size of 54.8 nm were synthesized successfully by the oxidant-peroxo method (OPM) and were used to prepare highly dense ceramic bodies which were sintered at 1100 and 1150 deg. C for 2 h. A tetragonal phase was identified in the powder and ceramic samples by X-ray powder diffraction and FT-Raman spectroscopy at room temperature. The fractured surface of the ceramic sample showed a high degree of densification with fairly uniform grain sizes. Dielectric constants measured in the range of 30-300 deg. C at different frequencies (120 Hz and at 1, 10 and 100 kHz) indicated that samples with 20 mol% praseodymium showed normal ferroelectric behavior regardless of the sintering temperature.

  20. The role of praseodymium substituted ions on electrical and magnetic properties of Mg spinel ferrites

    Energy Technology Data Exchange (ETDEWEB)

    Farid, Muhammad Tahir, E-mail: tahirfaridbzu@gmail.com; Ahmad, Ishtiaq; Kanwal, Muddassara; Murtaza, Ghulam; Ali, Irshad; Khan, Sajjad Ahmad

    2017-04-15

    Spinel ferrites with composition MgPr{sub y}Fe{sub 2−y}O{sub 4} (y=0.0, 0.025, 0.05, 0.075, 0.10) were successfully synthesized using sol-gel auto-combustion technique. The structural prisoperties of a prepared sintered powder were characterized with the help of X-ray Diffraction (XRD) and then also by using Scanning electron microscopy (SEM). Electrical measurements demonstrate that resistivity and activation energy increases with the Praseodymium substitution while dc resistivity decreases with the rise of temperature showing the semiconductor nature of the synthesized ferrites. Remanence and the saturation magnetization (M{sub s}) decrease while coercivity (H{sub c}) also increases with the increase in praseodymium contents. Anisotropic constant is observed to exhibit similar behavior as H{sub C}. The above mentioned parameters suggest that the synthesized samples are favorable for microwave absorbing purposes. - Highlights: • Magnesium based spinel ferrites were successfully synthesized by sol-gel method. • The spinel phase has been observed in all samples. • The dc resistivity are found to increase with increasing Pr content • The samples with high resistivity have high values of activation energy. • The Ms Decreases with increasing Pr contents while Hc increases.

  1. Eutrophication management in surface waters using lanthanum modified bentonite

    DEFF Research Database (Denmark)

    Copetti, Diego; Finsterle, Karin; Marziali, Laura

    2016-01-01

    This paper reviews the scientific knowledge on the use of a lanthanum modified bentonite (LMB) to manage eutrophication in surface water. The LMB has been applied in around 200 environments worldwide and it has undergone extensive testing at laboratory, mesocosm, and whole lake scales. The availa......This paper reviews the scientific knowledge on the use of a lanthanum modified bentonite (LMB) to manage eutrophication in surface water. The LMB has been applied in around 200 environments worldwide and it has undergone extensive testing at laboratory, mesocosm, and whole lake scales....... The available data underline a high efficiency for phosphorus binding. This efficiency can be limited by the presence of humic substances and competing oxyanions. Lanthanum concentrations detected during a LMB application are generally below acute toxicological threshold of different organisms, except in low...... alkalinity waters. To date there are no indications for long-term negative effects on LMB treated ecosystems, but issues related to La accumulation, increase of suspended solids and drastic resources depletion still need to be explored, in particular for sediment dwelling organisms. Application of LMB...

  2. The thermodynamic characteristics of vaporization of praseodymium triiodide

    Science.gov (United States)

    Motalov, V. B.; Kudin, L. S.; Markus, T.

    2009-03-01

    The vaporization of praseodymium triiodide was studied by high-temperature mass spectrometry. Monomeric (PrI3) and dimeric (Pr2I6) molecules and the PrI{4/-} and Pr2I{7/-} negative ions were recorded in saturated vapor over the temperature range 842-1048 K. The partial pressures of neutral vapor components were determined. The enthalpies of sublimation Δs H o(298.15 K) in the form of monomers (291 ± 10 kJ/mol) and dimers (400 ± 30 kJ/mol) were calculated by the second and third laws of thermodynamics. The equilibrium constants of ion-molecular reactions were measured and the enthalpies of the reactions determined. The enthalpies of formation Δf H o(298.15 K) of molecules and ions in the gas phase were calculated (-373 ± 11, -929 ± 31, -865 ± 25, and -1433 ± 48 kJ/mol for PrI3, Pr2I6, PrI{4/-}, and Pr2I{7/-}, respectively).

  3. High-temperature, Knudsen cell-mass spectroscopic studies on lanthanum oxide/uranium dioxide solid solutions

    International Nuclear Information System (INIS)

    Sunder, S.; McEachern, R.; LeBlanc, J.C.

    2001-01-01

    Knudsen cell-mass spectroscopic experiments were carried out with lanthanum oxide/uranium oxide solid solutions (1%, 2% and 5% (metal at.% basis)) to assess the volatilization characteristics of rare earths present in irradiated nuclear fuel. The oxidation state of each sample used was conditioned to the 'uranium dioxide stage' by heating in the Knudsen cell under an atmosphere of 10% CO 2 in CO. The mass spectra were analyzed to obtain the vapour pressures of the lanthanum and uranium species. It was found that the vapour pressure of lanthanum oxide follows Henry's law, i.e., its value is directly proportional to its concentration in the solid phase. Also, the vapour pressure of lanthanum oxide over the solid solution, after correction for its concentration in the solid phase, is similar to that of uranium dioxide. (authors)

  4. Synthesis characterization and sintering of cobalt-doped lanthanum chromite powders for use in SOFCs

    International Nuclear Information System (INIS)

    Yamagata, Chieko; Mello-Castanho, Sonia R.H.

    2009-01-01

    Doped lanthanum chromite is a promising as interconnect material because of its good conductivity at high temperatures and its stability in oxidizing and reducing atmospheres. Perovskite oxide powders of Co-doped lanthanum chromite were synthesized by dispersing precursor metal salt solutions in a polymer matrix followed by a thermal treatment. XRD patterns showed that a highly crystalline cobalt-doped lanthanum chromite was obtained. Fine perovskite powder with a surface area of 6.15 m 2 g -1 calcined at 700 deg C for 1 h, were obtained. After the sample sintered at 1450 deg C for 3h, the powder reached high densities exceeding 97% of the theoretical density. The proposed here has proved to be a very promising technique for the synthesis of lanthanum chromite powders. (author)

  5. Scanning Auger microscopy study of lanthanum partitioning in sphene-based glass-ceramics

    International Nuclear Information System (INIS)

    Hocking, W.H.; Hayward, P.J.; Watson, D.G.; Allen, G.C.

    1984-01-01

    Glass-ceramics are being investigated as possible hosts for the radioactive wastes that would result from recycling irradiated nuclear fuels. The partitioning of lanthanum in sphene-based glass-ceramics has been studied by scanning Auger electron microscopy for lanthanum concentrations from 0.2 to 2.0 mol.%. Sphene crystals (CaTiSiO 5 ) were located in the silica-rich glass matrix by recording digital Auger images of the calcium and titanium distributions. The sphene crystals were typically 0.5 to 5 μm in size and occupied approximately 40% of the total specimen volume. Auger spot analyses revealed that lanthanum was strongly partitioned into the sphene phase of phosphorus-free glass-ceramics; however, when a small amount of phosphorus was included in the glass-ceramic composition as a crystal nucleating agent, the lanthanum was concentrated in a third minor phase which also contained calcium, phosphorus and oxygen. Chemical shift effects in the Auger spectra of silicon, titanium and phosphorus showed evidence for electron-stimulated desorption of oxygen. (author)

  6. Bifunctional lanthanum phosphate substrates as novel adsorbents and biocatalyst supports for perchlorate removal

    International Nuclear Information System (INIS)

    Sankar, Sasidharan; Prajeesh, Gangadharan Puthiya Veetil; Anupama, Vijaya Nadaraja; Krishnakumar, Bhaskaran; Hareesh, Padinhattayil; Nair, Balagopal N.; Warrier, Krishna Gopakumar; Hareesh, Unnikrishnan Nair Saraswathy

    2014-01-01

    Graphical abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign thermal gelation process, performed the role of dual functional sorbent facilitating perchlorate adsorption and bioremediation through the growth of perchlorate reducing microbial colonies. - Highlights: • Lanthanum phosphate monoliths as efficient perchlorate adsorbents. • And also as substrates for biofilm (perchlorate reducing bacteria) growth. • Environmentally benign thermal gelation process for substrate fabrication. • 98% adsorption efficiency for perchlorate concentrations up to 100 μg/L. • The regenerated monoliths show nearly 100% reusability. - Abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign colloidal forming process employing methyl cellulose, are reported here as excellent adsorbents of perchlorate with >98% efficiency and with 100% reusability. Additionally, the effectiveness of such substrates as biocatalyst supports that facilitate biofilm formation of perchlorate reducing microbes (Serratia marcescens NIIST 5) is also demonstrated for the first time. The adsorption of perchlorate ions is attributed to the pore structure of lanthanum phosphate substrate and the microbial attachment is primarily ascribed to its intrinsic hydrophobic property. Lanthanum phosphate thus emerges as a dual functional material that possesses an integrated adsorption/bioremediation property for the effective removal of ClO 4 − which is an increasingly important environmental contaminant

  7. Bifunctional lanthanum phosphate substrates as novel adsorbents and biocatalyst supports for perchlorate removal

    Energy Technology Data Exchange (ETDEWEB)

    Sankar, Sasidharan [Materials Science and Technology Division (India); Prajeesh, Gangadharan Puthiya Veetil; Anupama, Vijaya Nadaraja [Process Engineering and Environmental Technology Division, CSIR – National Institute for Interdisciplinary Science and Technology, Industrial Estate P.O., Thiruvananthapuram 695019 (India); Krishnakumar, Bhaskaran [Process Engineering and Environmental Technology Division, CSIR – National Institute for Interdisciplinary Science and Technology, Industrial Estate P.O., Thiruvananthapuram 695019 (India); Academy of Scientific and Industrial Research (AcSIR) (India); Hareesh, Padinhattayil [Materials Science and Technology Division (India); Nair, Balagopal N. [R and D Centre, Noritake Co. Ltd., Aichi (Japan); Warrier, Krishna Gopakumar [Materials Science and Technology Division (India); Academy of Scientific and Industrial Research (AcSIR) (India); Hareesh, Unnikrishnan Nair Saraswathy, E-mail: hareesh@niist.res.in [Materials Science and Technology Division (India); Academy of Scientific and Industrial Research (AcSIR) (India)

    2014-06-30

    Graphical abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign thermal gelation process, performed the role of dual functional sorbent facilitating perchlorate adsorption and bioremediation through the growth of perchlorate reducing microbial colonies. - Highlights: • Lanthanum phosphate monoliths as efficient perchlorate adsorbents. • And also as substrates for biofilm (perchlorate reducing bacteria) growth. • Environmentally benign thermal gelation process for substrate fabrication. • 98% adsorption efficiency for perchlorate concentrations up to 100 μg/L. • The regenerated monoliths show nearly 100% reusability. - Abstract: Porous lanthanum phosphate substrates, obtained by an environmentally benign colloidal forming process employing methyl cellulose, are reported here as excellent adsorbents of perchlorate with >98% efficiency and with 100% reusability. Additionally, the effectiveness of such substrates as biocatalyst supports that facilitate biofilm formation of perchlorate reducing microbes (Serratia marcescens NIIST 5) is also demonstrated for the first time. The adsorption of perchlorate ions is attributed to the pore structure of lanthanum phosphate substrate and the microbial attachment is primarily ascribed to its intrinsic hydrophobic property. Lanthanum phosphate thus emerges as a dual functional material that possesses an integrated adsorption/bioremediation property for the effective removal of ClO{sub 4}{sup −} which is an increasingly important environmental contaminant.

  8. Separation of lanthanum (3) and samarium (3) extraction with tributylphosphate in the solvent presence of solid phase

    International Nuclear Information System (INIS)

    Korotkevich, I.B.; Kolesnikov, A.A.; Bomshtejn, V.E.

    1990-01-01

    Lanthanum (3) and samarium (3) extraction from nitric acid solutions by tributylphosphate in the presence of solid phase has been investigated. An increase in samarium α-nitrate distribution factor in the presence of solid phase with a decrease in its concentration in the initial solution and with lanthanum nitrate concentration increase is detected. The greatest effect of separation is observed in samarium nitrate microregion. The method of quantitative extraction of samarium from lanthanum nitrate solutions with samarium-lanthanum separation factor exceeding 50 has been suggested

  9. Lanthanum benzoyl acetonates: an IR and mass spectrometric study of the composition and structure

    International Nuclear Information System (INIS)

    Kostyuk, N.N.; Dik, T.A.; Tereshko, N.V.

    2005-01-01

    IR spectroscopy and mass spectrometry were used to study the structure of lanthanum chelates of benzoyl acetone (1-phenyl-1,3-butadione, HBA) of the following compositions: La(BA) 3 · EtOH, La(BA) 2 , La(BA) 2 · CH 3 CN, and La(BA) 2 · HDA, where EtOH = ethanol, HDA = nonadecanoic acid. It is demonstrated that a quasi-aromatic metalloring is formed in lanthanum chelates studied. Stable metal-containing fragments of the molecular ions of lanthanum bis- and tris-benzoylacetonate were identified [ru

  10. Synthesis and characterization of lanthanum incorporated mesoporous molecular sieves

    International Nuclear Information System (INIS)

    Pesquera, C.; Gonzalez, F.; Blanco, C.; Sanchez, L.

    2004-01-01

    A series of mesoporous materials under reflux conditions have been synthesized with two silicon sources (fumed silica and sodium silicate) and lanthanum added. The following Si/La molar ratio was used in the samples: 100; 75; 50 and 25. The calcined products were characterized by means of X-ray diffraction, nitrogen adsorption isotherms and energy dispersive X-ray spectrometry (EDS). The BET surface area gradually decreases with an increase in the lanthanum content of the LaxMCM-41 samples. Moreover, the average pore size tends to decrease along with the increase in the La content in the samples

  11. Physiological responses in barley to applications of lanthanum

    International Nuclear Information System (INIS)

    Reddy, N.; Maheswaran, J.; Peverill, K.; Meehan, B.

    1998-01-01

    Full text: Chinese research and glasshouse investigations carried out in Victoria by the authors have shown that several plant species, when treated with Rare Earth Elements (REEs), retain greater amounts of moisture under water stressed conditions. The physiological adaptation of the plant to retain moisture in response to REE treatment however, has not been investigated. A glasshouse trial is currently in progress to study the physiological and agronomic responses of barley (cv. Schooner) grown in pots to application of lanthanum (0, 5 and 10 kg/ha), at a concentration of 0.05%, under well-watered (field capacity) and water-deficit (25 - 30% field capacity) conditions. Lanthanum was applied both directly to the soil and as a foliar spray. The physiological measurements include, photosynthetic rate, leaf water potential, osmotic potential, relative water content, stomatal conductance and water use efficiency. Measured agronomic parameters include plant height, tiller production, leaf area development, total grain weight, total biomass, root and shoot ratio and harvest index. Analysis of plant tissue for N, P, K, Ca, Mg, Zn and La to study the relationship between application of REE and nutrient uptake is also being carried out. The paper discusses physiological and agronomic changes in barley plants in response to treatment with lanthanum, under conditions of water stress

  12. Formulation and Assessment of a Wash-Primer Containing Lanthanum "Tannate" for Steel Temporary Protection

    Science.gov (United States)

    D'Alessandro, Oriana; Selmi, Gonzalo J.; Deyá, Cecilia; Di Sarli, Alejandro; Romagnoli, Roberto

    2018-02-01

    Tannins are polyphenols synthesized by plants and useful for the coating industry as corrosion inhibitors. In addition, lanthanum salts have a great inhibitory effect on steel corrosion. The aim of this study was to obtain lanthanum "tannate" with adequate solubility to be incorporated as the corrosion inhibitor in a wash-primer. The "tannate" was obtained from commercial "Quebracho" tannin and 0.1 M La(NO3)3. The soluble tannin was determined by the Folin-Denis reagent, while the concentration of Lanthanum was obtained by a gravimetric procedure. The protective action of "tannate" on SAE 1010 steel was evaluated by linear polarization curves and corrosion potential measurements. Lanthanum "tannate" was incorporated in a wash-primer formulation and tested by corrosion potential and ionic resistance measurements. The corrosion rate was also determined by the polarization resistance technique. Besides, the primer was incorporated in an alkyd paint system and its anticorrosion performance assessed in the salt spray cabinet and by electrochemical impedance spectroscopy. Results showed that lanthanum "tannate" primer inhibits the development of deleterious iron oxyhydroxides on the steel substrate and incorporated into a paint system had a similar behavior to the primer formulated with zinc tetroxychromate.

  13. Separation of lanthanum (3) and neodymium (3) by tributyl phosphate extraction in the presence of solid phase

    International Nuclear Information System (INIS)

    Korotkevich, I.B.; Kolesnikov, A.A.; Bomshtejn, V.E.; Shikhaleeva, N.N.

    1987-01-01

    Lanthanum (3) and neodymium (3) extraction from nitric acid solutions by tributyl phosphate in the presence of solid phase of the element nitrates is investigated. An increase in distribution of neodymium nitrate in the presence of solid phase with the decrease in its concentration in the initial solution and with the increase in lanthanum nitrate concentration is detected. The highest effect of extractive-crystallizational separation is observed in the range of neodymium nitrate microconcentrations. A method of neodymium quantitative extraction from lanthanum nitrate solutions with neodymium - lanthanum separation coefficient exceeding 25 is suggested

  14. Leaching Kinetics of Praseodymium in Sulfuric Acid of Rare Earth Elements (REE) Slag Concentrated by Pyrometallurgy from Magnetite Ore

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Chul-Joo; Yoon, Ho-Sung; Chung, Kyung Woo; Lee, Jin-Young; Kim, Sung-Don; Shin, Shun Myung [Korea Institute of Geoscience and Mineral Resources, Daejeon (Korea, Republic of); Kim, Hyung-Seop; Cho, Jong-Tae; Kim, Ji-Hye; Lee, Eun-Ji; Lee, Se-Il; Yoo, Seung-Joon [Seonam University, Asan (Korea, Republic of)

    2015-02-15

    A leaching kinetics was conducted for the purpose of recovery of praseodymium in sulfuric acid (H{sub 2}SO{sub 4}) from REE slag concentrated by the smelting reduction process in an arc furnace as a reactant. The concentration of H{sub 2}SO{sub 4} was fixed at an excess ratio under the condition of slurry density of 1.500 g slag/L, 0.3 mol H{sub 2}SO{sub 4}, and the effect of temperatures was investigated under the condition of 30 to 80 .deg. C. As a result, praseodymium oxide (Pr{sub 6}O{sub 1}1) existing in the slag was completely converted into praseodymium sulfate (Pr{sub 2}(SO{sub 4}){sub 3}·8H{sub 2}O) after the leaching of 5 h. On the basis of the shrinking core model with a shape of sphere, the first leaching reaction was determined by chemical reaction mechanism. Generally, the solubility of pure REEs decreases with the increase of leaching temperatures in sulfuric acid, but REE slag was oppositely increased with increasing temperatures. It occurs because the ash layer included in the slag is affected as a resistance against the leaching. By using the Arrhenius expression, the apparent activation energy of the first chemical reaction was determined to be 9.195 kJmol{sup -1}. In the second stage, the leaching rate is determined by the ash layer diffusion mechanism. The apparent activation energy of the second ash layer diffusion was determined to be 19.106 kJmol{sup -1}. These relative low activation energy values were obtained by the existence of unreacted ash layer in the REE slag.

  15. Thermal, infrared and X-ray studies on praseodymium and neodymium myristates

    International Nuclear Information System (INIS)

    Upadhyaya, S.K.; Sharma, P.S.

    1993-01-01

    The thermal decomposition of praseodymium and neodymium myristates has been studied both as a function of temperature and of time. The thermogravimetric analysis has shown that order of decomposition reaction is kinetically of zero order and the energy of activation for the decomposition process lies in the range of 10-15 kcal mol -1 . The IR results showed that lanthanide myristates have an ionic character. The X-ray analysis indicated that the zigzag chains of the fatty acid radical constituent of the soap molecules extend straight forward on both sides of each basal plane and the molecular axes of the soap molecules are somewhat inclined to the basal plane. (author). 5 refs., 2 tabs

  16. Interfacial layers in tape cast anode-supported doped lanthanum gallate SOFC elements

    Energy Technology Data Exchange (ETDEWEB)

    Maffei, N.; De Silveira, G. [Materials Technology Laboratory, Natural Resources Canada, CANMET, 405 Rochester Street, Ottawa, Ontario (Canada) K1A OG3

    2003-04-01

    Lanthanum gallate doped with strontium and magnesium (LSGM) is a promising electrolyte system for intermediate temperature solid oxide fuel cells (SOFCs). The reported formation of interfacial layers in monolithic type SOFCs based on lanthanum gallate is of concern because of its impact on the performance of the fuel cell. Planar anode-supported SOFC elements (without the cathode) were prepared by the tape casting technique in order to determine the nature of the anode/electrolyte interface after sintering. Two anode systems were studied, one a NiO-CeO{sub 2} cermet, and the other, a modified lanthanum gallate anode containing manganese. Sintering studies were conducted at 1250, 1300, 1350, 1400 and 1450 C to determine the effect of temperature on the interfacial characteristics. Scanning electron microscopy (SEM) revealed a significant diffusion of Ni from the NiO-CeO{sub 2} anode resulting in the formation of an interfacial layer regardless of sintering temperature. Significant La diffusion from the electrolyte into the anode was also observed. In the case of the modified lanthanum gallate anode containing manganese, there was no interfacial layer formation, but a significant diffusion of Mn into the electrolyte was observed.

  17. Preparation of lanthanum ferrite powder at low temperature

    Energy Technology Data Exchange (ETDEWEB)

    Andoulsi, R.; Horchani-Naifer, K.; Ferid, M., E-mail: karima_horchani@yahoo.com [Physical Chemistry Laboratory of Mineral Materials and their Applications, Hammam-Lif (Tunisia)

    2012-01-15

    Single lanthanum ferrite phase was successfully prepared at low processing temperature using the polymerizable complex method. To implement this work, several techniques such as differential scanning calorimetry, X-ray diffraction, Fourier Transform Infrared Spectroscopy, scanning electron microscopy and BET surface area measurements were used. Throw the obtained results, it was shown that steps of preparing the powder precursor and temperature of its calcination are critical parameters for avoiding phase segregation and obtaining pure lanthanum ferrite compound. Thus, a single perovskite phase was obtained at 600 deg C. At this temperature, the powder was found to be fine and homogeneous with an average crystallite size of 13 nm and a specific surface area of 12.5 m{sup 2}.g{sup -1}. (author)

  18. Trimethylphosphide isomerization in lanthanum ions presence

    International Nuclear Information System (INIS)

    Zacharias, M.A.; Massabni, A.M.G.

    1984-01-01

    The integration between the trimethilphosphide and the lanthanum ions carry to the formation of solid complexes in a relation of 6:1 where the ligand is the phosphonate what is resultant of the isomerization of trimetylphosphite. By the RMN -1 H and infra-red spectra the products were characterized. (L.M.J.) [pt

  19. The air oxidation behavior of lanthanum ion implanted zirconium at 500 deg. C

    CERN Document Server

    Peng, D Q; Chen, X W; Zhou, Q G

    2003-01-01

    The beneficial effect of lanthanum ion implantation on the oxidation behavior of zirconium at 500 deg. C has been studied. Zirconium specimens were implanted by lanthanum ions using a MEVVA source at energy of 40 keV with a fluence range from 1x10 sup 1 sup 6 to 1x10 sup 1 sup 7 ions/cm sup 2 at maximum temperature of 130 deg. C, The weight gain curves were measured after being oxidized in air at 500 deg. C for 100 min, which showed that a significant improvement was achieved in the oxidation behavior of zirconium ion implanted with lanthanum compared with that of the as-received zirconium. The valence of the oxides in the scale was analyzed by X-ray photoemission spectroscopy; and then the depth distributions of the elements in the surface of the samples were obtained by Auger electron spectroscopy. Glancing angle X-ray diffraction at 0.3 deg. incident angles was employed to examine the modification of its phase transformation because of the lanthanum ion implantation in the oxide films. It was obviously fou...

  20. Structural properties of alkaline sodium lead fluoride borate glasses incorporated with Praseodymium ion

    Science.gov (United States)

    Lenkennavar, Susheela K.; Madhu, A.; Eraiah, B.; Kokila, M. K.

    2018-05-01

    The effect of different alkaline and Pr ions on the density and structure of Na2O-PbO-MO-B2O3 (M represents Ba/Ca/Sr) has been investigated using X-ray diffraction (XRD), infrared spectrophotometer (FTIR). The amorphous phase has been identified based on X-ray diffraction analysis. The Praseodymium oxide plays the role as a glass-modifier and influences on BO3↔BO4 conversion. The same effect is also observed in density and molar volume variation due to non bridging oxygen's (NBO) created when BO3 units are converted.

  1. Effect of noble metal doping on the structural properties of lanthanum cobaltite

    International Nuclear Information System (INIS)

    Dharmadhikari, Dipti V.; Athawal, Anjali A.

    2016-01-01

    Pristine and Noble metal (Ag and Pd) doped lanthanum cobaltite samples have been synthesised by Hydrothermal method. Lanthanum in the A-Site and Co at B-site of Lanthanum cobaltite (LaCoO 3 ) perovskites were partially doped by silver and palladium (4%). Crystal structure analysis revealed that the hydrothermal synthesis led to the formation of pure nanocrystalline perovskite structure. Morphological analysis of the samples shows that the noble metal doping affects the morphology of the samples. Pristine sample shows spherical to oval shaped particles while the doping results in the formation of irregular shaped, spherical and rod shaped particles. Silver doping results in the agglomeration of particles. The particles were observed to be fused with each other to form rod shaped structures in case of palladium doped samples. (author)

  2. Types of defect ordering in undoped and lanthanum-doped Bi2201 single crystals

    International Nuclear Information System (INIS)

    Martovitsky, V. P.

    2006-01-01

    Undoped and lanthanum-doped Bi2201 single crystals having a perfect average structure have been comparatively studied by x-ray diffraction. The undoped Bi2201 single crystals exhibit very narrow satellite reflections; their half-width is five to six times smaller than that of Bi2212 single crystals grown by the same technique. This narrowness indicates three-dimensional defect ordering in the former crystals. The lanthanumdoped Bi2201 single crystals with x = 0.7 and T c = 8-10 K exhibit very broad satellite reflections consisting of two systems (modulations) misoriented with respect to each other. The modulation-vector components of these two modulations are found to be q 1 = 0.237b* + 0.277c* and q 2 = 0.238b* + 0.037c*. The single crystals having a perfect average structure and a homogeneous average distribution of doping lanthanum consist of 70-to 80-A-thick layers that alternate along the c axis and have two different types of modulated superlattice. The crystals having a less perfect average structure also consist of alternating layers, but they have different lanthanum concentrations. The low value of T c in the undoped Bi2201 single crystals (9.5 K) correlates with three-dimensional defect ordering in them, and an increase in T c to 33 K upon lanthanum doping can be related to a thin-layer structure of these crystals and to partial substitution of lanthanum for the bismuth positions

  3. AB initio energetics of lanthanum substitution in ferroelectric bismuth titanate

    International Nuclear Information System (INIS)

    Shah, S.H.

    2012-01-01

    Density functional theory based electronic structure calculations play a vital role in understanding, controlling and optimizing physical properties of materials at microscopic level. In present study system of interest is bismuth titanate (Bi/sub 4/Ti/sub 3/O/sub 12/)/(BIT) which has wide range of applications such as a high temperature piezoelectric and one of the best material for memory devices. However, it also suffers from serious issues such as oxygen vacancies which degrade its performance as a memory element and piezoelectric material. In this context, the bulk and defect properties of orthorhombic bismuth titanate (Bi/sub 4/Ti/sub 3/O/sub 12/) and bismuth lanthanum titanate (Bi/sub 3.25/La/sub 0.75/Ti/sub 3/O/sub 12/)/(BLT, x=0.75) were investigated by using first principles calculations and atomistic thermodynamics. Heats of formation, valid chemical conditions for synthesis, lanthanum substitution energies and oxygen and bismuth vacancy formation energies were computed. The study improves understanding of how native point defects and substitutional impurities influence the ferroelectric properties of these layered perovskite materials. It was found that lanthanum incorporation could occur on either of the two distinct bismuth sites in the structure and that the effect of substitution is to increase the formation energy of nearby native oxygen vacancies. The results provide direct atomistic evidence over a range of chemical conditions for the suggestion that lanthanum incorporation reduces the oxygen vacancy concentration. Oxygen vacancies contribute to ferroelectric fatigue by interacting strongly with domain walls and therefore a decrease in their concentration is beneficial. (orig./A.B.)

  4. Phase segregation in cerium-lanthanum solid solutions

    NARCIS (Netherlands)

    Belliere, V.; Joorst, G; Stephan, O; de Groot, FMF; Weckhuysen, BM

    2006-01-01

    Electron energy-loss spectroscopy (EELS) in combination with scanning transmission electron microscopy ( STEM) reveals that the La enrichment at the surface of cerium-lanthanum solid solutions is an averaged effect and that segregation occurs in a mixed oxide phase. This separation occurs within a

  5. Structural characterization and properties of lanthanum film as chromate replacement for tinplate

    International Nuclear Information System (INIS)

    Huang Xingqiao; Li Ning

    2007-01-01

    Sulfide-stain resistance of La-passivated, unpassivated and Cr-passivated tinplate was measured using a cysteine tarnish test. Corrosion behavior of these tinplates was investigated using electrochemical impedance spectroscopy (EIS) measurement. The morphology, composition and thickness of lanthanum film were studied by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and X-ray fluorescence spectrometry (XRF), respectively. La-passivation treatment remarkably enhances sulfide-stain resistance of tinplate, and sulfide-stain resistance of La-passivated tinplate is slightly higher than that of Cr-passivated tinplate. La-passivation treatment also significantly improves corrosion protection property of tinplate. In contact with 3.5% NaCl solution, corrosion resistance of La-passivated tinplate is close to that of Cr-passivated tinplate, and in contact with 0.1 M citric-citrate buffer solution, corrosion resistance of La-passivated tinplate is higher than that of Cr-passivated tinplate. Lanthanum film is composed of spherical particles about 50-1000 nm in diameter, while most part of tinplate's surface is covered with the small particles about 50-200 nm. The film mainly consists of lanthanum and oxygen, which mainly exist as La 2 O 3 and its hydrates such as La(OH) 3 and LaOOH. The amount of lanthanum in the film is about 0.0409 g/m 2

  6. Effect of lanthanum doping on electrical and electromechanical ...

    Indian Academy of Sciences (India)

    Unknown

    temperature, Tc increased with the increase of lanthanum content. ... By adding oxide group softeners, hardeners and stabi- ... pressed with 2% polyvinyl alcohol as binder under a ... study are dependent on temperature and are shown in.

  7. Study of valence of cerium and praseodymium ions in Pr1-xCexO2 solid solutions

    International Nuclear Information System (INIS)

    Gartsman, K.G.; Kartenko, N.F.; Melekh, B.T.

    1990-01-01

    Effect of preparation conditions of Pr 1-x Ce x O 2 solid solutions on Ce and Pr ion valence within Pr 1-x Ce x O 2 system is studied. The data obtained enable to conclude that praseodymium may depending on annealing conditions change its state from Pr 3+ to Pr 4+ , while Ce 4+ is stable in Pr 1-x Ce x O 2 solid solutions

  8. Lanthanum Nitrate As Electrolyte Additive To Stabilize the Surface Morphology of Lithium Anode for Lithium-Sulfur Battery.

    Science.gov (United States)

    Liu, Sheng; Li, Guo-Ran; Gao, Xue-Ping

    2016-03-01

    Lithium-sulfur (Li-S) battery is regarded as one of the most promising candidates beyond conventional lithium ion batteries. However, the instability of the metallic lithium anode during lithium electrochemical dissolution/deposition is still a major barrier for the practical application of Li-S battery. In this work, lanthanum nitrate, as electrolyte additive, is introduced into Li-S battery to stabilize the surface of lithium anode. By introducing lanthanum nitrate into electrolyte, a composite passivation film of lanthanum/lithium sulfides can be formed on metallic lithium anode, which is beneficial to decrease the reducibility of metallic lithium and slow down the electrochemical dissolution/deposition reaction on lithium anode for stabilizing the surface morphology of metallic Li anode in lithium-sulfur battery. Meanwhile, the cycle stability of the fabricated Li-S cell is improved by introducing lanthanum nitrate into electrolyte. Apparently, lanthanum nitrate is an effective additive for the protection of lithium anode and the cycling stability of Li-S battery.

  9. Synthesis and characterization of lanthanum complex (5-choloro-8-hydroxy quinoline) bis (2-2'bipyridine) lanthanum La(Bpy)2(5-Clq)

    Science.gov (United States)

    Kumar, Rahul; Soam, Ankur; Bhargava, Parag

    2017-05-01

    Lanthanum complex, (5-choloro 8-hydroxy quinoline) bis (2-2'bipyridine) has been synthesized and characterized by different techniques. Lanthanum complex, La(Bpy)2(5-Clq) was characterized for structural, thermal and photoluminescence analysis. Structural analysis of this material was done by Fourier transformed infrared spectroscopy (FTIR) and mass spectroscopy. Thermal analysis of this material was done by thermal gravimetric analysis (TGA) and material shows the thermal stability up to 400°C. Absorption and emission spectra of the material was measured by UV-visible spectroscopy and photoluminescence spectroscopy. Solution of this material La(Bpy)2(5-Clq) in ethanol showed absorption peak at 332 nm, which may be attributed due to (π - π*) transitions. The photoluminescence spectra of La(Bpy)2(5-Clq) in ethanol solution showed intense peak at 505 nm.

  10. Properties of poly(vinyl alcohol)-borax gel doped with neodymium and praseodymium

    International Nuclear Information System (INIS)

    Lawrence, Mathias B.; Desa, J.A.E.; Rai, Renu; Aswal, V.K.

    2014-01-01

    Neodymium and praseodymium ions, singly and in combination, have been doped into a poly(vinyl alcohol)-borax matrix. X-ray diffraction shows structural correlations from 2 to 6 Å and 15 Å, while small angle neutron scattering indicates that the rare-earth ions do not affect the nanoscale structures of the gels. Differential scanning calorimetry shows the glass transition temperature to increase with concentration of Pr in the gel. Excitation in the ultraviolet region leads to luminescent emission in the visible region. Simultaneous absorption in the visible region then leads to luminescent emission in the near infra-red region. The spectral qualities of the emission bands can be varied by choosing appropriate relative ratios of rare-earth species. (author)

  11. Plasma spheroidization and high temperature stability of lanthanum phosphate and its compatibility with molten uranium

    International Nuclear Information System (INIS)

    Ananthapadmanabhan, P.V.; Sreekumar, K.P.; Thiyagarajan, T.K.; Satpute, R.U.; Krishnan, K.; Kulkarni, N.K.; Kutty, T.R.G.

    2009-01-01

    Lanthanum phosphate has excellent thermal stability and corrosion resistance against many molten metals and other chemically corrosive environments. Lanthanum phosphate (LaPO 4 ) was synthesized from lanthanum oxalate by thermal dissociation of the oxalate to the oxide, followed by conversion to hydrated lanthanum phosphate (LaPO 4 .0.5H 2 O). Thermal treatment of LaPO 4 .0.5H 2 O above 773 K resulted in the irreversible transformation of the hydrated phase to the stable monazite phase. Thermal and chemical stability of monazite was studied by plasma spheroidization experiments using a DC thermal plasma reactor set up. Compatibility of monazite with molten uranium was studied by thermal analysis. Results showed that monazite is thermally stable up to its melting point and also is resistant towards attack by molten uranium. Adherent coatings of LaPO 4 could be deposited onto various substrates by atmospheric plasma spray technique

  12. Investigation into complexing of phthalexone S with praseodymium ions and some aminoglycoside antibiotics

    International Nuclear Information System (INIS)

    Alykov, N.M.

    1981-01-01

    Complex formation of phthalexone S (Phth) with praseodymium ion and some aminoglycoside antibiotics (Ab) in aqueous ethanol solutions (1:1) has been examined photometrically at 619 mm. It has been shown that compounds with the ratios of Ab:Pr:Phth=1:2:8, 1:1:4, 1:1:3 are formed depending on the number of amino groups and structure of the antibiotics. The molar absorptivities and solubility products for the complexes have been calculated. The complex formation scheme is given. A procedure has been developed of determining 0.01-10 μg of antibiotics in 1 ml of a biological material with a relative error of less than 10% [ru

  13. Nanoscale photoelectron ionisation detector based on lanthanum hexaboride

    International Nuclear Information System (INIS)

    Zimmer, C.M.; Kunze, U.; Schubert, J.; Hamann, S.; Doll, T.

    2011-01-01

    A nanoscale ioniser is presented exceeding the limitation of conventional photoionisation detectors. It employs accelerated photoelectrons that allow obtaining molecule specificity by the tuning of ionisation energies. The material lanthanum hexaboride (LaB 6 ) is used as air stable photo cathode. Thin films of that material deposited by pulsed laser deposition (PLD) show quantum efficiency (QE) in the range of 10 -5 which is comparable to laser photo stimulation results. A careful treatment of the material yields reasonable low work functions even after surface reoxidation which opens up the possibility of using ultraviolet light emitting diodes (UV LEDs) in replacement of discharge lamps. Schematic diagram of a photoelectron ionisation detector (PeID) operating by an electron emitter based on the photoelectric effect of lanthanum hexaboride. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. The study of interaction of lanthanum-, cerium- and neodymium chlorides with sodium borohydride in pyridine- and tetrahydrofuran medium

    International Nuclear Information System (INIS)

    Mirsaidov, U.; Rotenberg, T.G.; Dymova, T.N.

    1976-01-01

    Bis-tetrahydrofurans of lanthanum and neodymium borohydrides and bis-pyridinates of lanthanum, cerium and neodymium borohydrides were obtained by interacting sodium borohydride with lanthanum-, cerium and neodymium chlorides in pyridine and tetrahydrofuran media. All operations involving reagent combination, sampling and phase separation are performed in inert atmosphere using argonvacuum equipment. The reaction in pyridine was virtually instantaneous and accompanied by flocculanet precipitation. The interaction of lanthanum chloride and neodymium chloride with sodium borohydride in tetrahydrofuran (THF) was a slow (23-30 hr) heterophase process. The interaction rate was affected by size reduction of the intial substances, temperature, reagent proportion and mixing rate. The reaction time was twice reduced with boiling tetrahydrofuran

  15. Plasma spheroidization and high temperature stability of lanthanum phosphate and its compatibility with molten uranium

    Energy Technology Data Exchange (ETDEWEB)

    Ananthapadmanabhan, P.V. [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)], E-mail: pvananth@barc.gov.in; Sreekumar, K.P.; Thiyagarajan, T.K.; Satpute, R.U. [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Krishnan, K.; Kulkarni, N.K. [Fuel Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Kutty, T.R.G. [Radiometallurgy Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

    2009-01-15

    Lanthanum phosphate has excellent thermal stability and corrosion resistance against many molten metals and other chemically corrosive environments. Lanthanum phosphate (LaPO{sub 4}) was synthesized from lanthanum oxalate by thermal dissociation of the oxalate to the oxide, followed by conversion to hydrated lanthanum phosphate (LaPO{sub 4}.0.5H{sub 2}O). Thermal treatment of LaPO{sub 4}.0.5H{sub 2}O above 773 K resulted in the irreversible transformation of the hydrated phase to the stable monazite phase. Thermal and chemical stability of monazite was studied by plasma spheroidization experiments using a DC thermal plasma reactor set up. Compatibility of monazite with molten uranium was studied by thermal analysis. Results showed that monazite is thermally stable up to its melting point and also is resistant towards attack by molten uranium. Adherent coatings of LaPO{sub 4} could be deposited onto various substrates by atmospheric plasma spray technique.

  16. On the extent of homogeneity region of PrP phase in the system praseodymium-phosphorus

    International Nuclear Information System (INIS)

    Mironov, K.E.

    1984-01-01

    For constructed by ion type compounds in the metal or metalloid systems homogeneity region boundary position can be observed at different compositions depending on which side the approximation to it occurs: on the metal or compound side. As an example the PrP homogeneity region in the praseodymium-phosphorus system is considered. An assumption is made on the prevalence of this phenomenon among rare earth monopnictides and monochalcogenides. For the PrP phase it is indicated that the monophopshide cell parameter depends on content of impurities in the initial metal, oxygen, in particular

  17. Lanthanum chromite colloidal processing

    International Nuclear Information System (INIS)

    Setz, Luiz Fernando Grespan

    2009-01-01

    Lanthanum chromite (LaCrO 3 ) is currently the most studied material for applications such as solid oxide fuel cell inter connector (HTSOFC). The complexity of microstructures and geometries of HTSOFC devices, require a precise control of processing parameters to get the desired combination of properties and this, the use of techniques involving concentrated ceramic slips conformation are appropriate, therefore, is well controlled, assist in obtaining homogeneous parts, reproductive and complex geometries. Thus, studies involving the surface chemistry, the stability conditions and slips flow behaviour in the forming conditions, provide important elements for processes control in the inter connectors manufacture, where more applied settings have slots and channels for the gases passage. Thus, surface chemistry, stability and rheological behaviour of strontium and cobalt doped LaCrO 3 (La) 0.80 Sr 0. 2 0 Cr 0.92 Co 0.08 O 3 ) slips prepared with ethanol and water, were studied. The doped lanthanum chromite was produced by combustion synthesis in the IPEN/SP labs. The influence of parameters: pH (water), dispersant concentration, homogenization times and conditions, solid concentration, different ratios binder:plasticizer in the stability and the flow behavior of ceramic suspensions prepared were evaluated. The La) 0.80 Sr 0. 2 0 Cr 0.92 Co 0.08 O 3 products obtained by casting aqueous slips in a plaster mould, using alkaline pH and anionic polyelectrolyte and tapes obtained by using ethanol as a dispersant medium, after sintering at 1600 degree C/4 hours presented theoretical density > 94%, suitable for use as HTSOFC inter connector. (author)

  18. Analysis and separation of lanthanide elements

    International Nuclear Information System (INIS)

    Almeida Pimentel, E. de.

    1973-01-01

    Improvements of rare earth separation by the combined use of acetic and critic acid were studied and analytical methods for determining some of the lanthanides were tryed out. Separations of the R.E. studied were favorable when citric acid (solution A) and acetic acid (solution B) were used in the proportion of 10:1 at pH=4,00. Neutron activation, spectro-photometric, polarographic, volumetric and gravimetric procedures allowed the determination of 8 R.E.; samarium, neodymium, praseodymium, lanthanum, cerium, holmium, erbium and europium

  19. Hyperfine coupling in gadolinium-praseodymium alloys by specific heat measurements; Etude du couplage hyperfin dans les alliages gadolinium-praseodyme par mesures de chaleur specifique

    Energy Technology Data Exchange (ETDEWEB)

    Michel, J [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1967-12-01

    We have studied the hyperfine coupling in gadolinium-praseodymium alloys by specific heat measurements down to 0.3 K. In the first part we describe the apparatus used to perform our measurements. The second part is devoted to some theoretical considerations. We have studied in detail the case of praseodymium which is an exception in the rare earth series. The third part shows the results we have obtained. (author) [French] Nous avons etudie le couplage hyperfin d'alliages de gadolinium-praseodyme par des mesures de chaleur specifique jusqu'a 0.3 K. Dans la premiere partie de cette etude nous decrivons le dispositif experimental. La deuxieme partie est consacree a des considerations theoriques. Nous avons etudie en detail le cas du praseodyme qui est une exception dans la serie des terres rares. La troisieme partie est consacree aux resultats experimentaux. (auteur)

  20. Synthesis, characterization and thermal expansion studies on thorium-praseodymium mixed oxide solid solutions

    International Nuclear Information System (INIS)

    Panneerselvam, G.; Antony, M.P.; Srinivasan, T.G.; Vasudeva Rao, P.R.

    2010-01-01

    Full text: Thorium-praseodymium mixed oxide solid solutions containing 15, 25, 40 and 55 mole percent of praseodymia were synthesized by mixing the solutions of thorium nitrate in water and praseodymium oxide (Pr 6 O 11 ) in conc. HNO 3 . Subsequently, their hydroxides were co-precipitated by the addition of aqueous ammonia. Further the precipitate was dried at 50 deg C, calcined at 600 deg C for 4 hours and sintered at 1200 deg C for 6 h in air. X-ray diffraction measurements were performed for phase identification and lattice parameter derivation. Single-phase fluorite structure was observed for all the compositions. Bulk and theoretical densities of solid solutions were also determined by immersion and X-ray techniques. Thermal expansion coefficients and percentage linear thermal expansion of the solid solutions were determined using high temperature X-ray diffraction technique in the temperature range 300 to 1700 K for the first time. The room temperature lattice constants estimated for above compositions are 0.5578, 0.5565, 0.5545 and 0.5526 nm, respectively. The mean linear thermal expansion coefficients for the solid solutions are 15.48 x 10 -6 K -1 , 18.35 x 10 -6 K -1 , 22.65 x 10 -6 K -1 and 26.95 x 10 -6 K -1 , respectively. The percentage linear thermal expansions in this temperature range are 1.68, 1.89, 2.21 and 2.51 respectively. It is seen that the solid solutions are stable up to 1700 K. It is also seen that the effect and nature of the dopant are the important parameters influencing the thermal expansion of the ThO 2 . The lattice parameter of the solid solutions exhibited a decreasing trend with respect to praseodymia addition. The percentage linear thermal expansion of the solid solutions increases steadily with increasing temperature

  1. Lake responses following lanthanum-modified bentonite clay (Phoslock) application: an analysis of water column lanthanum data from 16 case study lakes

    NARCIS (Netherlands)

    Spears, B.M.; Lürling, M.F.L.L.W.; Yasseri, S.; Castro-Castellon, A.T.; Gibbs, M.; Meis, S.; McDonald, C.; McIntosh, J.; Sleep, D.; Oosterhout, van F.

    2013-01-01

    Phoslock is a lanthanum (La) modified bentonite clay that is being increasingly used as a geo-engineering tool for the control of legacy phosphorus (P) release from lake bed sediments to overlying waters. This study investigates the potential for negative ecological impacts from elevated La

  2. Synthesis, Characterization and Thermal Diffusivity of Holmium and Praseodymium Zirconates

    Directory of Open Access Journals (Sweden)

    Stopyra M.

    2016-06-01

    Full Text Available A2B2O7 oxides with pyrochlore or defected fluorite structure are among the most promising candidates for insulation layer material in thermal barrier coatings. The present paper presents the procedure of synthesis of holmium zirconate Ho2Zr2O7 and praseodymium zirconate Pr2Zr2O7 via Polymerized-Complex Method (PCM. Thermal analysis of precursor revealed that after calcination at relatively low temperature (700°C fine-crystalline, single-phase material is obtained. Thermal diffusivity was measured in temperature range 25-200°C, Ho2Zr2O7 exhibits lower thermal diffusivity than Pr2Zr2O7. Additionally, PrHoZr2O7 was synthesized. The powder in as-calcined condition is single-phase, but during the sintering decomposition of solid solution took place and Ho-rich phase precipitated. This material exhibited the best insulating properties among the tested ones.

  3. On dependence of stability of lanthanum complexes with aminopolycarboxylic acids on the complex structure

    International Nuclear Information System (INIS)

    Poluehktov, N.S.; Meshkova, S.B.; Danilkovich, M.M.; Topilova, Z.M.

    1985-01-01

    Regularities in changes of stability constants of lanthanum complexes with aminopolycarboxylic acids (APA) versus their structure are studied, The stability of lathanum-APA complexes depends mainly on the number of carboxyl groups in a ligand molecule. At that, the highest stability constant is characteristic of a complex with a ligand, containing 3 nitrogen atoms and 5 carboxyl groups, in the presenoe of which the lanthanum ion coordination sphere gets satupated. The oxyethy group introduction into a ligand molecule also improves the lanthanum complex stability but to a lesser degree than during the introduction of a carboxyl group. The number of nitrogen atoms in a ligand polecule affects insignificantly the complex stability constant value, and the elongation of a chain of CH 2 groups, separating nitrogen atoms, reduces the constant to a -0.6 power

  4. Order parameters in lanthanum gallate lightly doped with manganese and paramagnetic resonance

    Science.gov (United States)

    Vazhenin, V. A.; Potapov, A. P.; Artyomov, M. Yu.; Guseva, V. B.

    2010-09-01

    The Cr3+ centers have been revealed, transitions at room temperature have been identified, and spin Hamiltonian parameters have been determined for the Cr3+ and Fe3+ triclinic centers in lanthanum gallate lightly doped with manganese. The principal axes of the fourth-rank fine-structure tensor for the Fe3+ triclinic centers have been established and used to determine the order parameters, i.e., the angles of rotation of oxygen octahedra of lanthanum gallate with respect to the perovskite structure. The order parameter in the rhombohedral phase has been estimated.

  5. Textile Dye Removal from Aqueous Solution using Modified Graphite Waste/Lanthanum/Chitosan Composite

    Science.gov (United States)

    Kusrini, E.; Wicaksono, B.; Yulizar, Y.; Prasetyanto, EA; Gunawan, C.

    2018-03-01

    We investigated various pre-treatment processes of graphite waste using thermal, mechanical and chemical methods. The aim of this work is to study the performance of modified graphite waste/lanthanum/chitosan composite (MG) as adsorbent for textile dye removal from aqueous solution. Effect of graphite waste resources, adsorbent size and lanthanum concentration on the dye removal were studied in batch experiments. Selectivity of MG was also investigated. Pre-heated graphite waste (NMG) was conducted at 80°C for 1 h, followed by mechanical crushing of the resultant graphite to 75 μm particle size, giving adsorption performance of ˜58%, ˜67%, ˜93% and ˜98% of the model dye rhodamine B (concentration determined by UV-vis spectroscopy at 554 nm), methyl orange (464 nm), methylene blue (664 nm) and methyl violet (580 nm), respectively from aqueous solution. For this process, the system required less than ˜5 min for adsorbent material to be completely saturated with the adsorbate. Further chemical modification of the pre-treated graphite waste (MG) with lanthanum (0.01 – V 0.03 M) and chitosan (0.5% w/w) did not improve the performance of dye adsorption. Under comparable experimental conditions, as those of the ‘thermal-mechanical-pre-treated-only’ (NMG), modification of graphite waste (MG) with 0.03 M lanthanum and 0.5% w/w chitosan resulted in ˜14%, ˜47%, ˜72% and ˜85% adsorption of rhodamine B, methyl orange, methylene blue and methyl violet, respectively. Selective adsorption of methylene blue at most to ˜79%, followed by methyl orange, methyl violet and rhodamine B with adsorption efficiency ˜67, ˜38, and ˜9% sequentially using MG with 0.03 M lanthanum and 0.5% w/w chitosan.

  6. XPS characterisation of in situ treated lanthanum oxide and hydroxide using tailored charge referencing and peak fitting procedures

    International Nuclear Information System (INIS)

    Sunding, M.F.; Hadidi, K.; Diplas, S.; Lovvik, O.M.; Norby, T.E.; Gunnaes, A.E.

    2011-01-01

    Highlights: → Gold particles deposited in vacuum as energy reference for insulating samples in XPS. → Separation of La 3d and MNN peaks in XP spectra acquired with Al Kα radiation. → We describe the spectral differences between lanthanum oxide and lanthanum hydroxide. → A doublet in O 1s of La 2 O 3 is ascribed to two distinct oxygen sites in the crystal. - Abstract: A technique is described for deposition of gold nanoparticles under vacuum, enabling consistent energy referencing of X-ray photoelectron spectra obtained from lanthanum hydroxide La(OH) 3 and in situ treated lanthanum oxide La 2 O 3 powders. A method is also presented for the separation of the overlapping lanthanum 3d and MNN peaks in X-ray photoelectron spectra acquired with Al Kα radiation. The lower satellite intensity in La(OH) 3 compared to La 2 O 3 is related to the higher ionicity of the La-O bond in the former compared to the latter compound. The presence of an additional peak in the valence band spectrum of the hydroxide compared to the oxide is attributed to the O-H bond as indicated by density functional theory based calculations. A doublet in the O 1s peak of lanthanum oxide is associated to the presence of two distinct oxygen sites in the crystal structure of this compound.

  7. Electrochemical corrosion of lanthanum chromite and yttrium chromite in coal slag

    Energy Technology Data Exchange (ETDEWEB)

    Marchant, D.D.; Bates, J.L.

    1981-01-01

    Lanthanum chromites have long been considered as electrodes for magnetohydrodynamic (MHD) generator channels. These chromites, when doped with divalent ions such as Ca, Mg or Sr, have adequate electronic and electrical conductivity (2), and melting points greater than 2500/sup 0/K. However, above approx. 1850/sup 0/K, selective vapor loss of chromium results in the formation of a La/sub 2/O/sub 3/ phase. The La/sub 2/O/sub 3/ is hydroscopic at room temperature, resulting in a large volume change and loss of mechanical integrity when exposed to H/sub 2/O. The analogous yttrium chromites have thermal and electrical properties similar to that for the lanthanum chromites. Although vapor loss of Cr results in the formation of Y/sub 2/O/sub 3/, this oxide does not hydrate. Corrosion studies of yttrium chromite compositions show that doped YCrO/sub 3/ may be a viable MHD electrode. An electrochemical corrosion study of both magnesium-doped lanthanum and yttrium chromites in synthetic coal slag electrolytes is described. Possible chemical and electrochemical degradation phenomena, as well as the relative rates of corrosion are emphasized.

  8. Phase transformations in lead zirconate-titanate doped with lanthanum

    Energy Technology Data Exchange (ETDEWEB)

    Ishchuk, V M; Morozov, E M

    1979-07-01

    Presented are the results of studies on the character of phase transitions of the lead-lanthanum zirconate-titanate (LLZT) system. The replacement of lead by lanthanum leads to the expansion of the region of antisegnetoelectric (ASE) states of solid solutions of lead zirconate-titanate (LZT) in the direction of PbTiO/sub 3/ concentration growth. An intermediate region is revealed between segnetoelectric (SE) and ASE states, material properties in which depend on their prehistory: annealed samples are in the ASE state, whereas the application of electric field exceeding some critical value induces the SE state. A family of phase diagrams obtained at consequent replacement of lead by lanthanum permits to identify phase states in any series of LLZT with a constant ratio of Zr:Ti, in the x/65/35 series in particular. Thermally depolarized state of materials of this series at x<6.5 is shown to be antisegnetoelectric at all the temperatures below the Curie point Tsub(c), and heating causes phase transition of ASE..-->..PE (paraelectric state) at Tsub(c). Polarized samples being heated, a successiveness of phase transitions of SE..-->..ASE takes place at T/sub 0/, and that of ASE reversible PE at Tsub(C) (Tsub(0)..ASE phase transition in the LZT system.

  9. Spectral intensities and bonding parameters for some praseodymium(III) and neodymium(III) complexes with benzimidazoles

    Energy Technology Data Exchange (ETDEWEB)

    Vyas, P C; Ojha, C K; Mittal, S; Joshi, G K

    1988-09-01

    The electronic spectral intensity parameters (Judd-Ofelt; Tsub(lambda)) calculated from absorption spectral data for the complexes of praseodymium(III) and neodymium(III) nitrates with benzimidazole and 2-methyl-, 2-ethyl- and 2-n-propyl-benzimidazoles are reported. The conductance of these derivatives in dimethylformamide suggests 1:1 electrolytic nature. The infrared spectral data indicate the presence of Csub(2v) as well Dsub(2h)-nitrate ions in the complexes. The correlation of the intensity of hypersensitive transitions with bonding (nephelauxetic ratio and degree of covalency) parameters are also reported. (author). 13 refs., 2 tables.

  10. Pr4N2S3 and Pr4N2Se3: two non-isostructural praseodymium(iii) nitride chalcogenides

    International Nuclear Information System (INIS)

    Lissner, Falk; Schleid, Thomas

    2005-01-01

    The non-isostructural nitride chalcogenides of praseodymium, Pr 4 N 2 S 3 and Pr 4 N 2 Se 3 , are formed by the reaction of the praseodymium metal with sodium azide (NaN 3 ), praseodymium trihalide (PrX 3 ; X = Cl, Br, I) and the respective chalcogen (sulfur or selenium) at 900 C in evacuated silica ampoules after seven days. Both crystallize monoclinically in space group C2/c (Pr 4 N 2 S 3 : a = 1788.57(9), b = 986.04(5), c = 1266.49(6) pm, β = 134.546(7) , Z = 8; Pr 4 N 2 Se 3 : a = 1311.76(7), b = 1017.03(5), c = 650.42(3) pm, β = 90.114(6) , Z = 4). The crystal structures of both compounds show a layered construction, dominated by N 3- -centred (Pr 3+ ) 4 tetrahedra which share a common edge first. Continuing linkage of the so resulting bitetrahedral [N 2 Pr 6 ] 12+ units via the non-connected vertices to layers according to [stack ∞ 2 ]{[N(Pr) 2/2 e (Pr') 2/2 v ] 3+ } forms different kinds of tetrahedral nets which can be described as layers consisting of ''four- and eight-rings'' for Pr 4 N 2 S 3 and as layers of ''six-rings'' for Pr 4 N 2 Se 3 . Whereas the crystal structure of Pr 4 N 2 S 3 exhibits four different Pr 3+ cations with coordination numbers of six (2 x) and seven (2 x) against N 3- and S 2- , the number of cations in the nitride selenide (Pr 4 N 2 Se 3 ) is reduced to half (Pr1 and Pr2) also having six- and sevenfold anionic coordination spheres. Further motifs for the connection of [NM 4 ] 9+ tetrahedra in crystal structures of nitride chalcogenides and halides of the rare-earth elements with ratios of N: M = 1: 2 are presented and discussed. (Abstract Copyright [2005], Wiley Periodicals, Inc.) [de

  11. XPS characterisation of in situ treated lanthanum oxide and hydroxide using tailored charge referencing and peak fitting procedures

    Energy Technology Data Exchange (ETDEWEB)

    Sunding, M.F., E-mail: m.f.sunding@fys.uio.no [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway); Hadidi, K. [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway); Diplas, S. [Department of Chemistry and Centre for Material Science and Nanotechnology (SMN), University of Oslo, P.O. Box 1033 Blindern, NO-0315 Oslo (Norway); SINTEF Materials and Chemistry, P.O. Box 124 Blindern, NO-0314 Oslo (Norway); Lovvik, O.M. [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway); SINTEF Materials and Chemistry, P.O. Box 124 Blindern, NO-0314 Oslo (Norway); Norby, T.E. [Department of Chemistry and Centre for Material Science and Nanotechnology (SMN), University of Oslo, P.O. Box 1033 Blindern, NO-0315 Oslo (Norway); Gunnaes, A.E. [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway)

    2011-07-15

    Highlights: {yields} Gold particles deposited in vacuum as energy reference for insulating samples in XPS. {yields} Separation of La 3d and MNN peaks in XP spectra acquired with Al K{alpha} radiation. {yields} We describe the spectral differences between lanthanum oxide and lanthanum hydroxide. {yields} A doublet in O 1s of La{sub 2}O{sub 3} is ascribed to two distinct oxygen sites in the crystal. - Abstract: A technique is described for deposition of gold nanoparticles under vacuum, enabling consistent energy referencing of X-ray photoelectron spectra obtained from lanthanum hydroxide La(OH){sub 3} and in situ treated lanthanum oxide La{sub 2}O{sub 3} powders. A method is also presented for the separation of the overlapping lanthanum 3d and MNN peaks in X-ray photoelectron spectra acquired with Al K{alpha} radiation. The lower satellite intensity in La(OH){sub 3} compared to La{sub 2}O{sub 3} is related to the higher ionicity of the La-O bond in the former compared to the latter compound. The presence of an additional peak in the valence band spectrum of the hydroxide compared to the oxide is attributed to the O-H bond as indicated by density functional theory based calculations. A doublet in the O 1s peak of lanthanum oxide is associated to the presence of two distinct oxygen sites in the crystal structure of this compound.

  12. Lanthanum Deposition in the Stomach in the Absence of Helicobacter pylori Infection.

    Science.gov (United States)

    Iwamuro, Masaya; Urata, Haruo; Tanaka, Takehiro; Kawano, Seiji; Kawahara, Yoshiro; Kimoto, Katsuhiko; Okada, Hiroyuki

    2018-03-15

    In this case report, we describe two patients who showed a diffusely whitish mucosa in the posterior wall and the lesser curvature of the gastric body. The patients were serologically- and histopathologically-negative for Helicobacter pylori. Random biopsy specimens from the stomach revealed no regenerative changes, intestinal metaplasia, and/or foveolar hyperplasia in either of the patients. Although lanthanum deposition in the gastric mucosa has been reported to occur in close association with H. pylori-associated gastritis, our patients tested negative for H. pylori. These cases suggest that lanthanum deposition presents as whitish lesions in the gastric body in H. pylori-negative patients.

  13. Properties of lanthanum hexaboride a compilation

    CERN Document Server

    Fisher, D J

    2013-01-01

    Lanthanum hexaboride is useful because it possesses a high melting point (2210C), a low work function, one of the highest known electron emissivities, and is stable in vacuum. This volume summarises the extant data on the properties of this material, including the: bulk modulus, conductivity, crystal structure, Debye temperature, defect structure, elastic constants, electronic structure, emissivity, Fermi surface, hardness, heat capacity, magnetoresistance, reflectivity, resistivity, specific heat, surface structure, thermal conductivity, thermoelectric power, toughness and work function. The

  14. Lake responses following lanthanum-modified bentonite clay (Phoslock®) application: an analysis of water column lanthanum data from 16 case study lakes.

    Science.gov (United States)

    Spears, Bryan M; Lürling, Miquel; Yasseri, Said; Castro-Castellon, Ana T; Gibbs, Max; Meis, Sebastian; McDonald, Claire; McIntosh, John; Sleep, Darren; Van Oosterhout, Frank

    2013-10-01

    Phoslock(®) is a lanthanum (La) modified bentonite clay that is being increasingly used as a geo-engineering tool for the control of legacy phosphorus (P) release from lake bed sediments to overlying waters. This study investigates the potential for negative ecological impacts from elevated La concentrations associated with the use of Phoslock(®) across 16 case study lakes. Impact-recovery trajectories associated with total lanthanum (TLa) and filterable La (FLa) concentrations in surface and bottom waters were quantified over a period of up to 60 months following Phoslock(®) application. Both surface and bottom water TLa and FLa concentrations were 0.8 mEq L(-1)), but higher (up to 0.12 mg L(-1)) in lakes characterised by very low alkalinity. The effects of elevated La(3+) concentrations following Phoslock(®) applications in lakes of very low alkalinity requires further evaluation. The implications for the use of Phoslock(®) in eutrophication management are discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Study on the influence of optical electronegativity of fluoride host structures on the crystal field components' position of the [Xe]4f15d1-configuration of trivalent praseodymium

    International Nuclear Information System (INIS)

    Herden, Benjamin

    2014-03-01

    As alternative radiation sources for mercury containing lamps LEDs cover the normal range, but efficient alternatives for UV radiations are still not available. Xenon excimer discharge lamps could be candidate as alternatives to mercury low-pressure discharge lamps. The discharge wavelength of these lamps is 172 nm that has to be converted in other spectral ranges. The theses deals with trivalent praseodymium as activator ion in binary and ternary fluoride host structures. The host structure and the crystallographic position of the praseodymium ion influence the development of emissions line and bands and the energetic position of the emission. The results are explained by the interaction of the nephelauxetic effect and the crystal field splitting of 5d orbitals, called optical electronegativity.

  16. Optical and physical properties of sodium lead barium borate glasses doped with praseodymium ion

    Science.gov (United States)

    Lenkennavar, Susheela K.; Madhu, A.; Eraiah, B.; Kokila, M. K.

    2018-05-01

    Praseodymium doped sodium lead barium borate glasses have been prepared using single step melt quenching technique. The XRD spectrum confirms amorphous nature of glasses. The optical absorbance studies were carried out on these glasses using PekinElemer Lambda-35 Uv-Vis spectrometer in the range of 200 -1100 nm. The optical direct band gap energies were found to be in the range of 3.62 eV to 3.69 eV and indirect band gap energies were found to be in the range of 3.57 eV to 3.62eV. The refractive indices were measured by using Abbe refractometer the values are in the range of 1.620 to 1.625.

  17. Conductometric study of lanthanum chloride interaction with potash soaps of higher fatty acids

    International Nuclear Information System (INIS)

    Skrylev, L.D.; Sazonova, V.F.; Kornelli, M.Eh.; Shumilina, N.A.

    1978-01-01

    Interaction of lanthanum chloride with potassium salts of higher aliphatic acids, containing from 10 to 16 carbon atoms, at room temperature in weakly acid media (pH=5.5) gives rise to neutral soaps of the La[CHsub(3)(CHsub(2))sub(n)COO]sub(3) composition, while in alkaline media (pH=8.0) base soaps of the LaOH[CHsub(3)(CHsub(2))sub(n)COO]sub(2) composition are formed. In acid solutions (pH=2.0) no interaction of lanthanum chloride with potassium soaps of the above carboxylic acids is observed

  18. Experimental investigation of the stability diagram for Paul traps in the case of praseodymium ions

    International Nuclear Information System (INIS)

    Koczorowski, W.; Szawiola, G.; Walaszyk, A.; Buczek, A.; Stefanska, D.; Stachowska, E.

    2006-01-01

    The present paper describes an investigation of non-linear resonances of praseodymium ion clouds stored in a Paul trap as a function of the storage parameters. These have been observed in traps with different ring electrode diameters. In these different traps the resonances occur for different values of the operating parameters. Discrepancies with the approximation model for one ion have been found. The intensity of the fluorescence signal and the Doppler half width have been recorded as a function of one of the storage parameters: q. We use our results to optimize the fluorescence signal of the stored ions, which is especially useful in the case of the double-resonance method.

  19. Room temperature synthesis of high temperature stable lanthanum phosphate–yttria nano composite

    International Nuclear Information System (INIS)

    Sankar, Sasidharan; Raj, Athira N.; Jyothi, C.K.; Warrier, K.G.K.; Padmanabhan, P.V.A.

    2012-01-01

    Graphical abstract: A facile aqueous sol–gel route involving precipitation–peptization mechanism followed by electrostatic stabilization is used for synthesizing nanocrystalline composite containing lanthanum phosphate and yttria. Highlights: ► A novel lanthanum phosphate–Y 2 O 3 nano composite is synthesized for the first time using a modified facile sol gel process. ► The composite becomes crystalline at 600 °C and X-ray diffraction pattern is indexed for monoclinic LaPO 4 and cubic yttria. ► The composite synthesized was tested up to 1300 °C and no reaction between the phases of the constituents is observed with the morphologies of the phases being retained. -- Abstract: A facile aqueous sol–gel route involving precipitation–peptization mechanism followed by electrostatic stabilization is used for synthesizing nanocrystalline composite containing lanthanum phosphate and yttria. Lanthanum phosphate (80 wt%)–yttria (20 wt%) nano composite (LaPO 4 –20%Y 2 O 3 ), has an average particle size of ∼70 nm after heat treatment of precursor at 600 °C. TG–DTA analysis reveals that stable phase of the composite is formed on heating the precursor at 600 °C. The TEM images of the composite show rod shape morphology of LaPO 4 in which yttria is acquiring near spherical shape. Phase identification of the composite as well as the phase stability up to 1300 °C was carried out using X-ray diffraction technique. With the phases being stable at higher temperatures, the composite synthesized should be a potential material for high temperature applications like thermal barrier coatings and metal melting applications.

  20. Structural consideration with respect to the thermal stability of a new platinum supported lanthanum-alumina catalyst

    International Nuclear Information System (INIS)

    Oudet, F.; Bordes, E.; Courtine, P.; Maxant, G.; Lambert, C.; Guerlet, J.P.

    1987-01-01

    The influence of lanthanum aluminate, LaAlO 3 , on the thermal stability of both alumina and platinum supported alumina catalysts is investigated. In the case of alumina, the stabilization is interpreted in terms of structural coherence between δ-Al 2 O 3 and a three-fold superstructure of LaAlO 3 . The addition of LaAlO 3 , is shown to increase both the dispersion and the resistance to sintering of the platinum supported alumina catalyst. Moreover, lanthanum hexa-aluminate (La-β-Al 2 O 3 ) is present in the platinum catalyst fired at 1150 0 C. These observations are assumed to result for the epitaxial relations between platinum and the lanthanum-alumina support. 23 refs.; 8 figs.; 2 tabs

  1. Investigation of paramagnetic saturation in lanthanum manganese nitrate

    NARCIS (Netherlands)

    Flokstra, Jakob; Meijer, H.C.; Bots, G.J.C.; Verheij, W.A.; van der Marel, L.C.

    1973-01-01

    Paramagnetic saturation of lanthanum manganese nitrate, La2Mn3(NO3)12·24H2O, has been investigated at liquid He temperatures in a static as well as a dynamical way. With the aid of the molecular-field theory the Casimir and Du Pré dispersion and absorption curves are adapted explicitly to the

  2. Deposition barium titanate (BaTiO3) doped lanthanum with chemical solution deposition

    International Nuclear Information System (INIS)

    Iriani, Y.; Nurhadi, N.; Jamaludin, A.

    2016-01-01

    Deposition of Barium Titanate (BaTiO 3 ) thin films used Chemical Solution Deposition (CSD) method and prepared with spin coater. BaTiO 3 is doped with lanthanum, 1%, 2%, and 3%. The thermal process use annealing temperature 900°C and holding time for 3 hours. The result of characterization with x-ray diffraction (XRD) equipment show that the addition of La 3+ doped on Barium Titanate caused the change of angle diffraction.The result of refine with GSAS software shows that lanthanum have been included in the structure of BaTiO 3 . Increasing mol dopant La 3+ cause lattice parameter and crystal volume become smaller. Characterization result using Scanning Electron Microscopy (SEM) equipment show that grain size (grain size) become smaller with increasing mole dopant (x) La 3+ . The result of characterization using Sawyer Tower methods show that all the samples (Barium Titanante and Barium Titanate doped lanthanum) are ferroelectric material. Increasing of mole dopant La 3+ cause smaller coercive field and remanent polarization increases. (paper)

  3. Eucalyptus tolerance mechanisms to lanthanum and cerium: subcellular distribution, antioxidant system and thiol pools.

    Science.gov (United States)

    Shen, Yichang; Zhang, Shirong; Li, Sen; Xu, Xiaoxun; Jia, Yongxia; Gong, Guoshu

    2014-12-01

    Guanglin 9 (Eucalyptus grandis × Eucalyptus urophlla) and Eucalyptus grandis 5 are two eucalyptus species which have been found to grow normally in soils contaminated with lanthanum and cerium, but the tolerance mechanisms are not clear yet. In this study, a pot experiment was conducted to investigate the tolerance mechanisms of the eucalyptus to lanthanum and cerium. Cell walls stored 45.40-63.44% of the metals under lanthanum or cerium stress. Peroxidase and catalase activities enhanced with increasing soil La or Ce concentrations up to 200 mg kg(-1), while there were no obvious changes in glutathione and ascorbate concentrations. Non-protein thiols concentrations increased with increasing treatment levels up to 200 mg kg(-1), and then decreased. Phytochelatins concentrations continued to increase under La or Ce stress. Therefore, the two eucalyptus species are La and Ce tolerant plants, and the tolerance mechanisms include cell wall deposition, antioxidant system response, and thiol compound synthesis. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. Fabrication of Polycrystalline Lanthanum Manganite (La0.99 Mn0.01 O3) Powder and Fibres by Electrospinning Method

    International Nuclear Information System (INIS)

    Yin Yin Win; That Htar Lwin; Than Than Win; Yin Maung Maung; Ko Ko Kyaw Soe

    2011-12-01

    Lanthanum manganite (La0.99 Mn0.01 O3) powder have been prepared by using pyrolysis methods. Lanthanum manganite fibres were successfully fabricated by electro-spinning utilizing precursors. Polycrystalline perovskite structure lanthanum manganite powder and fibres showed that the grain size and crystal grain increased significantly with the increase in calcination temperature. A variety of techniques (SEM, FT-IR and TG-DTA) were employed to study the morphology and fibre quality, crystal structure, and thermal analysis of La0.99 Mn0.01 O3 specimen respectively.

  5. The Catalytic Activity of Modified Zeolite Lanthanum on the Catalytic Cracking of Al-Duara Atmospheric Distillation Residue

    Directory of Open Access Journals (Sweden)

    Karim Khalifa Esgair

    2016-03-01

    Full Text Available Atmospheric residue fluid catalytic cracking was selected as a probe reaction to test the catalytic performance of modified NaY zeolites and prepared NaY zeolites. Modified NaY zeolites have been synthesized by simple ion exchange methods. Three samples of modified zeolite Y have been obtained by replacing the sodium ions in the original sample with lanthanum and the weight percent added are 0.28, 0.53, and 1.02 respectively. The effects of addition of lanthanum to zeolite Y in different weight percent on the cracking catalysts were investigated using an experimental laboratory plant scale of fluidized bed reactor. The experiments have been performed with weight hourly space velocity (WHSV range of 6 to 24 h-1, and the range of temperature from 450 to 510 oC. The activity of the catalyst with 1.02 wt% lanthanum has been shown to be much greater than that of the sample parent NaY. Also it was observed that the addition of the lanthanum causes an increase in the thermal stability of the zeolite.

  6. Evaluating United States and world consumption of neodymium, dysprosium, terbium, and praseodymium in final products

    Science.gov (United States)

    Hart, Matthew

    This paper develops scenarios of future rare-earth-magnet metal (neodymium, dysprosium, terbium, and praseodymium) consumption in the permanent magnets used in wind turbines and hybrid electric vehicles. The scenarios start with naive base-case scenarios for growth in wind-turbine and hybrid-electric-vehicle sales over the period 2011 to 2020, using historical data for each good. These naive scenarios assume that future growth follows time trends in historical data and does not depend on any exogenous variable. Specifically, growth of each technological market follows historical time trends, and the amount of rare earths used per unit of technology remains fixed. The chosen reference year is 2010. Implied consumptions of the rare earth magnet metals are calculated from these scenarios. Assumptions are made for the material composition of permanent magnets, the market share of permanent-magnet wind turbines and vehicles, and magnet weight per unit of technology. Different scenarios estimate how changes in factors like the material composition of magnets, growth of the economy, and the price of a substitute could affect future consumption. Each scenario presents a different method for reducing rare earth consumption and could be interpreted as potential policy choices. In 2010, the consumption (metric tons, rare-earth-oxide equivalent) of each rare-earth-magnet metal was as follows. Total neodymium consumption in the world for both technologies was 995 tons; dysprosium consumption was 133 tons; terbium consumption was 50 tons; praseodymium consumption was zero tons. The base scenario for wind turbines shows there could be strong, exponential growth in the global wind turbine market. New U.S. sales of hybrid vehicles would decline (in line with the current economic recession) while non-U.S. sales increase through 2020. There would be an overall increase in the total amount of magnetic rare earths consumed in the world. Total consumption of each rare earth in the short

  7. Stability constant of the lanthanum complex with humic acid

    International Nuclear Information System (INIS)

    Jimenez R, M.; Solache R, M. J.

    2008-01-01

    The work described here is a study on the formation of trivalent lanthanum complex with humic acid. Commercial humic acid was purified and then characterized by various analytical techniques. The stability constant determined by a radiochemical method has a worth of log β La , AHA = 13.6. (Author)

  8. Revised energy levels of singly ionized lanthanum

    Science.gov (United States)

    Güzelçimen, Feyza; Tonka, Mehdi; Uddin, Zaheer; Bhatti, Naveed Anjum; Windholz, Laurentius; Kröger, Sophie; Başar, Gönül

    2018-05-01

    Based on the experimental wavenumbers of 344 spectral lines from calibrated Fourier transform (FT) spectra as well as wavenumbers of 81 lines from the wavelength tables from literature, the energy of 115 fine structure levels of singly ionized lanthanum has been revised by weighted global fits. The classifications of the lines are provided by numerous previous investigations of lanthanum by different spectroscopic methods and authors. For the high accurate determination of the center of gravity wavenumbers from the experimental spectrum, the hyperfine constants of the involved levels have been taken into account, if possible. For the 94 levels with known hyperfine constants the accuracy of energy values is better than 0.01 cm-1. For 34 levels the magnetic dipole hyperfine constants A have been determined from FT spectra as part of this work. For four of these 34 levels even electric quadrupole hyperfine constants B could be estimated. For levels, which have experimentally unknown hyperfine constants and which are connected only by lines not found in the FT spectra but taken from literature, the uncertainties of energy values are about a factor of 10 higher. A list of all revised level energies together with a compilation of hyperfine structure data is given as well as a list of all lines used.

  9. Effects of intravenously injected lanthanum chloride on the femur of rats

    International Nuclear Information System (INIS)

    Miyagawa, Makoto; Daimon, Tateo

    2010-01-01

    Lanthanum (La) is widely used in industry and medicine. Because of lanthanum's physicochemical resemblance to calcium, the possible effects of it on bone have to be considered. The aim of this study was to examine the effects of La on bone toxicity. Rats were intravenously administrated with lanthanum chloride at 5 mg La/kg per week for five weeks. Histomorphometric analysis of femurs were performed using micro-CT scan. Compared with normal controls, the total bone area of the femur did not show any change in La-administrated rats, whereas the trabecular area slightly decreased. The trabecular bone mineral density in the experimented rats was higher than that in the normal controls, although the mineral density of the cortical bone and cancerou one was unchanged after the administration of La. La did not alter mechanical barometers of the femur such as mean cross-sectional moment of inertia, minimum cross-sectional moment of inertia and polar moment of inertia. Additionally, light microscopic analysis of the femurs revealed that histological features of osteoid, calcification front and bone matrix were normal after the administration of La. La was detected in the macrophages in the bone marrow, but not in the bone matrix by histological stain for La and X-ray fluorescence microanalysis. Thus, these micro-CT imaging and microscopy of the femurs did not reveal toxic changes due to La. (author)

  10. Microstructured fibers with high lanthanum oxide glass core for nonlinear applications

    Science.gov (United States)

    Kobelke, J.; Schuster, K.; Litzkendorf, D.; Schwuchow, A.; Kirchhof, J.; Bartelt, H.; Tombelaine, V.; Leproux, P.; Couderc, V.; Labruyere, A.

    2009-05-01

    We demonstrate a low loss microstructured fiber (MOF) with a high nonlinear glass core and silica holey cladding. The substitution of mostly used silica as core material of microstructured fibers by lanthanum oxide glass promises a high nonlinear conversion efficiency for supercontinuum (SC) generation. The glass composition is optimized in terms of thermochemical and optical requirements. The glass for the MOF core has a high lanthanum oxide concentration (10 mol% La2O3) and a good compatibility with the silica cladding. This is performed by adding a suitable alumina concentration up to 20 mol%. The lanthanum oxide glass preform rods were manufactured by melting technique. Besides purity issues the material homogeneity plays an important role to achieve low optical loss. The addition of fluorides allows the better homogenization of the glass composition in the preform volume by refining. The minimum attenuation of an unstructured fiber drawn from this glass is about 0.6 dB/m. It is mostly caused by decreasing of scattering effects. The microstructured silica cladding allows the considerable shifting of dispersive behavior of the MOF for an optimal pump light conversion. The MOF shows zero dispersion wavelengths (ZDW) of 1140 nm (LP01 mode) and 970 nm (LP11 mode). The supercontinuum generation was investigated with a 1064 nm pump laser (650 ps). It shows a broad band emission between 500 nm and 2200 nm.

  11. Preparation, characterization and optical properties of Lanthanum-(nanometer MCM-41) composite materials

    International Nuclear Information System (INIS)

    Zhai, Q. Z.; Wang, P.

    2008-01-01

    Nanometer MCM-41 molecular sieve was prepared under a base condition by using cetyltrimethylammonium bromide as template and tetraethyl orthosilicate as silica source by means of hydrothermal method. Lanthanum(III) was incorporated into the nanometer MCM-41 by a liquid phase grafting method. The prepared nano composite materials were characterized by means of powder X-ray diffraction, spectrophotometric analysis, Fourier transform infrared spectroscopy, low temperature nitrogen adsorption-desorption technique, solid diffuse reflectance absorption spectra and luminescence. The powder X-ray diffraction studies show that the nanometer MCM-41 molecular sieve is successfully prepared. The highly ordered meso porous two-dimensional hexagonal channel structure and framework of the support MCM-41 is retained intact in the prepared composite material La-(nanometer MCM-41). The spectrophotometric analysis indicates that lanthanum exists in the prepared nano composite materials. The Fourier transform infrared spectra indicate that the framework of the MCM-41 molecular sieve still remains in the prepared nano composite materials and some framework vibration peaks show blue shifts relative to those of the MCM-41 molecular sieve. The low temperature nitrogen adsorption-desorption indicates that the guest locales in the channel of the molecular sieve. Compared with bulk lanthanum oxide, the guest in the channel of the molecular sieve has smaller particle size and shows a significant blue shift of optical absorption band in solid diffuse reflectance absorption spectra. The observed blue shift in the solid state diffuse reflectance absorption spectra of the lanthanum-(nanometer MCM-41) sample show the obvious stereoscopic confinement effect of the channel of the host on the guest, which further indicates the successful encapsulation of the guest in the host. The La-(nanometer MCM-41) sample shows luminescence

  12. Energetically benign synthesis of lanthanum silicate through “silica garden” route and its characterization

    Energy Technology Data Exchange (ETDEWEB)

    Parmar, Kavita [Central University of Jharkhand, Ranchi (India); Bhattacharjee, Santanu, E-mail: santanu@nmlindia.org [CSIR-National Metallurgical Laboratory, Jamshedpur (India)

    2017-06-15

    Lanthanum silicate synthesis through “silica garden” route has been reported as an alternative to energy intensive milling procedure. Under optimum conditions lanthanum chloride crystals react with water glass (sodium silicate) to produce self generating hollow lanthanum silicate precipitation tube(s) (LaSPT). The micro tubes are irregular, thick, white coloured and amorphous but are hierarchically built from smaller tubules of 10–20 nm diameters. They retain their amorphous nature on being heated up to 600 °C beyond which crystallization starts. The major phase in the LaSPT heated at 900 °C is La{sub 2}Si{sub 2}O{sub 7}. “As synthesized” LaSPT is heterogeneous and comprises non stoichiometric phases. The exterior and interior surfaces of these tubes are remarkably different in their morphology and chemical composition. LaSPT sintered at 1200 and 1300 °C show fair amount of ionic conductivity. - Graphical abstract: Lanthanum silicate precipitation tube (LaSPT) produced through ‘silica garden’ route offers a green alternative to energy intensive milling procedure. - Highlights: • La-silicate precipitation tube (LaSPT) synthesized via silica garden route. • The microtubes are irregular, thick, white coloured and amorphous. • They are hierarchically built from smaller tubules of 10–20 nm diameters. • The major phase in the LaSPT heated at 900 °C is La{sub 2}Si{sub 2}O{sub 7}. • LaSPT sintered at 1200 °C is fairly conducting.

  13. Energetically benign synthesis of lanthanum silicate through “silica garden” route and its characterization

    International Nuclear Information System (INIS)

    Parmar, Kavita; Bhattacharjee, Santanu

    2017-01-01

    Lanthanum silicate synthesis through “silica garden” route has been reported as an alternative to energy intensive milling procedure. Under optimum conditions lanthanum chloride crystals react with water glass (sodium silicate) to produce self generating hollow lanthanum silicate precipitation tube(s) (LaSPT). The micro tubes are irregular, thick, white coloured and amorphous but are hierarchically built from smaller tubules of 10–20 nm diameters. They retain their amorphous nature on being heated up to 600 °C beyond which crystallization starts. The major phase in the LaSPT heated at 900 °C is La_2Si_2O_7. “As synthesized” LaSPT is heterogeneous and comprises non stoichiometric phases. The exterior and interior surfaces of these tubes are remarkably different in their morphology and chemical composition. LaSPT sintered at 1200 and 1300 °C show fair amount of ionic conductivity. - Graphical abstract: Lanthanum silicate precipitation tube (LaSPT) produced through ‘silica garden’ route offers a green alternative to energy intensive milling procedure. - Highlights: • La-silicate precipitation tube (LaSPT) synthesized via silica garden route. • The microtubes are irregular, thick, white coloured and amorphous. • They are hierarchically built from smaller tubules of 10–20 nm diameters. • The major phase in the LaSPT heated at 900 °C is La_2Si_2O_7. • LaSPT sintered at 1200 °C is fairly conducting.

  14. Effects of lanthanum exposure on elemental distribution in rat brains measured by synchrotron radiation XRF

    International Nuclear Information System (INIS)

    Feng Liuxing; Xiao Haiqing; He Xiao; Liu Nianqing; Zhao Yuliang; Chai Zhifang; Zhang Zhiyong

    2005-01-01

    Rare earth elements (REEs) comprise a coherent series of 15 elements from lanthanum to lutetium and possessing very similar chemical properties. In recent decades, with the rapid increase of the exploitation of REE resources and their applications to modern industry and daily life, particularly to agriculture as fertilizer additives in China, more and more REEs are coming into environmental system as well as food chain through various ways. It has become increasingly important to obtain more information on the physiological function of REEs and their long-term biological effects on body of living beings. Epidemiological investigations found that the intelligence quotients (IQ) of children from the REE-high background regions are obviously different from that of the normal region. This indicated that REEs probably affect the function of brain. However, the mechanism is totally unknown. The contents and distributions of major and trace elements are sometimes good indicators of the physiological and pathological conditions of human and animal brains In this study, the effects of subchronic lanthanum exposure on the elemental distribution in the rat brains were studied. Wistar rats were exposed to lanthanum chloride through oral administration at O, 0.1, 2, and 40-mg/kg doses for 6 months. The elements such as Cl, K, Ca, Fe, Cu, and Zn in brain slices were identified by synchrotron radiation X-ray fluorescence analysis. Differences in two-dimensional maps of elemental distribution were noticed. Cl, Ca, and Zn were primarily concentrated in hippocampus of the controls. With the increase of the lanthanum dosage, the Ca and Zn levels were significantly decreased, while the Cu levels were significantly elevated in cortex, hippocampus and thalamus. Our results suggest that subchronic lanthanum exposure in rats appears to change elemental distribution in brain. The impact of lanthanides on brain function is not negligible.

  15. Synthesis in aqueous medium and organic praseodymium complexes with ligands derived from Schiff base quinolinic. Characterization and physicochemical study; Sintesis en medio acuoso y organico de complejos de praseodimio con ligantes derivados de base de Schiff quinolicos. Caracterizacion y estudio fisicoquimico

    Energy Technology Data Exchange (ETDEWEB)

    Garcia G, A.

    2015-07-01

    It was investigated the coordination ability of the quinolinic Schiff base organic tetradentate quinolinic ligand (Q Schiff-(OH){sub 2}) towards the trivalent praseodymium by UV/Vis spectrophotometric titration (St). By St, was studied the formed species between the Q Schiff-(OH){sub 2} ligand and the praseodymium nitrate salt in equimolar concentrations (5.86 x 10{sup -4} M: 5.22 x 10{sup -4} M) in methanol. The statistical analysis of the experimental results suggested three complexed species with 1Pr:3L, 1Pr:2L y 1Pr:1L stoichiometries. The predominant stoichiometries were the second and the latter. Based on these results and data from the scientific literature, the methodology for the syntheses of the complexes Q Schiff-(OH){sub 2}-Pr in aqueous-organic and organic media was established and a molar ratio M:L= 1:2 of praseodymium nitrate and the ligand was used. The new complexes were characterized by UV/Vis, Infrared, X-ray Photoelectron Spectroscopy (XP S), Diffuse Reflectance (Dr) and Thermogravimetric Analysis/Differential Scanning Calorimetry (TGA/DSC). Elemental analysis of C, N, O and Pr by XP S suggested 1Pr:2L:1Na (PrC{sub 32}H{sub 20}N{sub 4}O{sub 4}Na) stoichiometry of the complex synthesized by the aqueous-organic medium while for the complex synthesized by the organic medium it was 1Pr:3L (PrC{sub 48}H{sub 33}N{sub 6}O{sub 6}). In the first case, the praseodymium ion charge was neutralized by the anionic ligands whose remaining charge was compensated by the sodium ion. In the second case, the ion charge was neutralized by the ligands. The minimum formula was Pr(Q Schiff){sub 2}Na for the pure coordination compound from the aqueous-organic medium and the minimum formula Pr(Q Schiff){sub 3} for that from the organic medium. XP S also indicated that the oxidation state of praseodymium ion was maintained. Both complexes were stable in methanol, ethanol and acetonitrile at least for 5 days. The photophysical properties of the studied complexes were

  16. The rare earth element (REE) lanthanum (La) induces hormesis in plants.

    Science.gov (United States)

    Agathokleous, Evgenios; Kitao, Mitsutoshi; Calabrese, Edward J

    2018-07-01

    Lanthanum is a rare earth element (REE) which has been extensively studied due to its wide application in numerous fields with a potential accumulation in the environment. It has long been known for its potential to stimulate plant growth within a hormetic-biphasic dose response framework. This article provides evidence from a series of high resolution studies published within the last two decades demonstrating a substantial and significant occurrence of lanthanum-induced hormesis in plants. These findings suggest that hormetic responses should be built into the study design of hazard assessment study protocols and included in the risk assessment process. Hormesis also offers the opportunity to substantially improve cost benefit estimates for environmental contaminants, which have the potential to induce beneficial/desirable effects at low doses. Copyright © 2018 Elsevier Ltd. All rights reserved.

  17. Responses in sediment phosphorus and lanthanum concentrations and composition across 10 lakes following applications of lanthanum modified bentonite

    DEFF Research Database (Denmark)

    Dithmer, Line; Nielsen, Ulla Gro; Lürling, Miquel

    2016-01-01

    and binding forms, P adsorption capacity of discrete sediment layers, and pore water P concentrations. Lanthanum phosphate mineral phases were confirmed by solid state (31)P MAS NMR and LIII EXAFS spectroscopy. Rhabdophane (LaPO4 · nH2O) was the major phase although indications of monazite (LaPO4) formation...... conditions of P retention (with the exception of two lakes) by sediments, indicating effective control of sediment P release, i.e. between two and nine years after treatment....

  18. Yttrium and lanthanum recovery from low cerium carbonate, yttrium carbonate and yttrium concentrate

    International Nuclear Information System (INIS)

    Vasconcelos, Mari Estela de

    2006-01-01

    In this work, separation, enrichment and purification of lanthanum and yttrium were performed using as raw material a commercial low cerium rare earth concentrate named LCC (low cerium carbonate), an yttrium concentrate named 'yttrium carbonate', and a third concentrated known as 'yttrium earths oxide. The first two were industrially produced by the late NUCLEMON - NUCLEBRAS de Monazita e Associados Ltda, using Brazilian monazite. The 'yttrium earths oxide' come from a process for preparation of lanthanum during the course of the experimental work for the present thesis. The following techniques were used: fractional precipitation with urea; fractional leaching of the LCC using ammonium carbonate; precipitation of rare earth peroxycarbonates starting from the rare earth complex carbonates. Once prepared the enriched rare earth fractions the same were refined using the ion exchange chromatography with strong cationic resin without the use of retention ion and elution using the ammonium salt of ethylenediaminetetraacetic acid. With the association of the above mentioned techniques were obtained pure oxides of yttrium (>97,7%), lanthanum (99,9%), gadolinium (96,6%) and samarium (99,9%). The process here developed has technical and economic viability for the installation of a large scale unity. (author)

  19. Electrical behaviour of strontium-doped lanthanum manganite interfaces

    DEFF Research Database (Denmark)

    Koch, Søren; Hendriksen, P.V.; Jacobsen, Torben

    2005-01-01

    The contact resistance of strontium-doped lanthanum manganite (LSM) contact pairs is investigated by polarisation analysis at different temperatures and atmospheres. The ceramic contacts have a high contact resistance, and strongly nonlinear current–voltage behaviour is observed at low temperatur....... The nonlinear behaviour is ascribed to the presence of energy barriers at the contact interface. Generally, point contacts showed a more linear behaviour than plane contact interfaces....

  20. Progressing batch hydrolysis process

    Science.gov (United States)

    Wright, J.D.

    1985-01-10

    A progressive batch hydrolysis process is disclosed for producing sugar from a lignocellulosic feedstock. It comprises passing a stream of dilute acid serially through a plurality of percolation hydrolysis reactors charged with feed stock, at a flow rate, temperature and pressure sufficient to substantially convert all the cellulose component of the feed stock to glucose. The cooled dilute acid stream containing glucose, after exiting the last percolation hydrolysis reactor, serially fed through a plurality of pre-hydrolysis percolation reactors, charged with said feedstock, at a flow rate, temperature and pressure sufficient to substantially convert all the hemicellulose component of said feedstock to glucose. The dilute acid stream containing glucose is cooled after it exits the last prehydrolysis reactor.

  1. Selective isotope determination of lanthanum by diode-laser-initiated resonance-ionization mass spectrometry

    International Nuclear Information System (INIS)

    Young, J.P.; Shaw, R.W.

    1995-01-01

    A diode-laser step has been incorporated into a resonance-ionization mass spectrometry optical excitation process to enhance the isotopic selectivity of the technique. Lanthanum isotope ratio enhancements as high as 10 3 were achieved by use of a single-frequency cw diode laser tuned to excite the first step of a three-step excitation--ionization optical process; the subsequent steps were excited by use of a pulsed dye laser. Applying the same optical technique, we measured atomic hyperfine constants for the high-lying even-parity 4 D 5/2 state of lanthanum at 30 354 cm --1 . The general utility of this spectral approach is discussed

  2. Oriented growing and anisotropy of emission properties of lanthanum hexaboride single crystals

    International Nuclear Information System (INIS)

    Lazorenko, V.I.; Lotsko, D.V.; Platonov, V.F.; Kovalev, A.V.; Galasun, A.P.; Matvienko, A.A.; Klinkov, A.E.

    1987-01-01

    Single crystals of lanthanum hexaboride with preset crystallographic orientation are grown by the method of crucible-free zone melting. It is shown that oriented growing of single crystals of the given compound is possible only when using seed crystals of the required orientation because no predominant orientation of the LaB 6 growth is found in case of spontaneous crystallization. Orientation of spontaneously growing LaB 6 crystals does not depend on their growth rate, degree of the melt diffusion annealing, purity of the inital powder. Anisotropy of the electronic work function for single crystal lanthanum hexaboride is confirmed. Its value grows as (100)<(110)<(111). Conditions of the preliminary thermovacuum purification of the surface are shown to affect the measured work function

  3. Thermoelectric power and electrical conductivity of strontium-doped lanthanum manganite

    DEFF Research Database (Denmark)

    Ahlgren, E.O.; Poulsen, F.W.

    1996-01-01

    Thermoelectric power and electrical conductivity of pure and 5, 10 and 20% strontium-doped lanthanum manganite are determined as function of temperature in air and of P-O2 at 1000 degrees C. At high temperatures the thermoelectric power is negative. Both thermoelectric power and conductivity...

  4. A case of lanthanum carbonate ingestion thought to be phlebosclerotic colitis on CT imaging and abdominal radiograph

    International Nuclear Information System (INIS)

    Harris, K.; Balcam, S.

    2017-01-01

    A male admitted in the early hours of the morning, complained of a four week, right sided, non-radiating, dull and intermittent abdominal pain. Imaging suggested a diagnosis of phlebosclerotic colitis which was later discounted when the patients' history of lanthanum carbonate ingestion was examined. Phlebosclerotic colitis mostly affects the Asian population, and its cause is still not known, but can be associated with specific radiographic features. Collections of lanthanum may confuse a diagnosis of phlebosclerotic colitis as well as other factors such as voxel errors, photon starvation and movement. - Highlights: • PC can be non-specific, its cause unknown, diagnosis is often delayed. • PC depends on specific radiographic features. • Lanthanum Carbonate can collect within the lumen and confuses diagnosis. • Voxel errors, photon starvation and patient movement can displace densities.

  5. On magnetic ordering in heavily sodium substituted hole doped lanthanum manganites

    Energy Technology Data Exchange (ETDEWEB)

    Sethulakshmi, N. [Department of Physics, Cochin University of Science and Technology, Cochin 682022, Kerala (India); Unnimaya, A.N. [Centre for Materials for Electronic Technology (CMET), Thrissur 680581, Kerala (India); Al-Omari, I.A.; Al-Harthi, Salim [Department of Physics, Sultan Qaboos University, PC 123 Muscat (Oman); Sagar, S. [Government College for Women, Thiruvananthapuram 695014, Kerala (India); Thomas, Senoy [Materials Science and Technology Division, National Institute for Interdisciplinary Science and Technology, Thiruvananthapuram 695019, Kerala (India); Srinivasan, G. [Department of Physics, Oakland University, Rochester (United States); Anantharaman, M.R., E-mail: mraiyer@yahoo.com [Department of Physics, Cochin University of Science and Technology, Cochin 682022, Kerala (India)

    2015-10-01

    Mixed valence manganite system with monovalent sodium substituted lanthanum manganites form the basis of the present work. Lanthanum manganites belonging to the series La{sub 1−x}Na{sub x}MnO{sub 3} with x=0.5–0.9 were synthesized using modified citrate gel method. Variation of lattice parameters and unit cell volume with Na concentration were analyzed and the magnetization measurements indicated ferromagnetic ordering in all samples at room temperature. Low temperature magnetization behavior indicated that all samples exhibit antiferromagnetism along with ferromagnetism and it has also been observed that antiferromagnetic ordering dominates ferromagnetic ordering as concentration is increased. Evidence for such a magnetic inhomogeneity in these samples has been confirmed from the variation in Mn{sup 3+}/Mn{sup 4+} ion ratio from X-ray Photoelectron Spectroscopy and from the absorption peak studies using Ferromagnetic Resonance Spectroscopy. - Highlights: • Higher substitution of more than 50 percent of monovalent ion, sodium for La sites in lanthanum manganites scarce in literature. • Structural studies using XRD and further structure refinement by Rietveld refinement confirmed orthorhombic pbnm spacegroup. • Ferromagnetic behavior at room temperature with saturation magnetization decreasing with increase in sodium concentration. • M vs T measurements using FC ZFC proved coexisting FM/AFM behavior arising from exchange interactions between different valence states of Mn ions. • Disparity in ratio of Mn valence ions indicated presence of vacancies providing the role of vacancies and oxygen stoichiometry in deciding magnetic inhomogeneity.

  6. Self-assembly in lanthanum(III) and calcium(II) complexes of salicylaldimines derived from putrescine

    International Nuclear Information System (INIS)

    Pospieszna-Markiewicz, Izabela; Kaczmarek, Malgorzata T.; Kubicki, Maciej; Radecka-Paryzek, Wanda

    2008-01-01

    The one-step template reaction of salicylaldehyde with putrescine, a biogenic diamine, in the presence of lanthanum(III) or calcium(II) ions produces salicylaldimine complexes containing the N,N'-bis(salicylidene)-1,4-butanediamine ligand L as a result of the [2 + 1] Schiff base condensation. The X-ray diffraction studies of the lanthanum complex reveals an infinite [La 2 L 4 (NO 3 ) 6 ] ∞ polymeric structure based on networks of 10-coordinated La(III) nodes linked by bridging unionized ligands that use exclusively the oxygens as donor atoms with the nitrogen atoms not being involved in coordination

  7. Application of the Rietveld method in powders of strontium-doped lanthanum manganite calcined in different temperatures

    International Nuclear Information System (INIS)

    Chiba, R.; Vargas, R.A.; Martinez, L.G.; Andreoli, M.; Seo, E.S.M.

    2010-01-01

    The strontium-doped lanthanum manganite (LSM) is a ceramic material used as cathode in device called High Temperature Solid Oxide Fuel Cell. In this work, the LSM was synthesized by the citrate technique with the objective to get powders without the formation of secondary phases, such as lanthanum oxide and the lanthanum hydroxide, harmful for the functional performance of the device. The definitive calcination temperatures had been 700, 900 and 1100 deg C, due the decomposition of the polymeric precursors to present stabilization from 480 deg C. The analysis by X-ray diffraction of the calcined powders in different temperatures shows the formation only of phase LSM of hexagonal crystalline structure, type pseudo-perovskite. Using the refinement of Rietveld was determined the parameters and volumes of unity cells, atomic positions and occupations. These results confirm that the chemical compositions obtained are similar to the nominal. (author)

  8. Effect of voltage on the characteristics of magnesium-lanthanum deposits synthesized by an electrodeposition process

    Energy Technology Data Exchange (ETDEWEB)

    Sahli, M. [Laboratoire de Physique Energétique, Université de Constantine 1 (Algeria); Chetehouna, K.; Gascoin, N. [INSA-CVL, Univ. Orléans, PRISME, EA 4229, F-18020, Bourges (France); Bellel, N. [Laboratoire de Physique Energétique, Université de Constantine 1 (Algeria); Tadini, P., E-mail: tadini.pietro@gmail.com [INSA-CVL, Univ. Orléans, PRISME, EA 4229, F-18020, Bourges (France)

    2017-04-15

    This work deals with the characterization of magnesium-lanthanum powders deposits produced with an electrodeposition technique using an aqueous solution based on magnesium chloride and lanthanum(III) nitrate. In recent years, the interest for magnesium-based alloys is growing due to their potential use as solid state systems for hydrogen storage. This work is a preliminary study on the synthesis of magnesium-lanthanum powders oriented to their later evaluation in systems for hydrogen storage. Magnesium and Lanthanum are deposited on a copper plate used as a cathode. Chemical composition, structure and morphology are investigated by EDS, XRD, FTIR and SEM. The effect of voltage on powders characteristics is studied considering three values (3, 3.5 and 4 V). EDS analysis shows the presence of three major elements (Mg, La and O) with a little amount of Cl. The weight percentages of Mg and O increase whereas the one of La decreases with the growth of voltage. Morphological characterization reveals that heterogeneous chemical structures are formed on the surface of the electrode and the size of aggregates decreases with the increase of voltage. From the results of X-ray analysis the deposits reveal the significant presence of two phases: Mg(OH){sub 2} and La(OH){sub 3}. The peaks originating from the Mg(OH){sub 2} phase has a non-monotonic behavior and those of La(OH){sub 3} phase increase with the increase of voltage. FTIR analysis confirms the presence of the two phases identified in XRD diffractograms and exhibits that their corresponding transmittance values increase for higher voltage values. - Highlights: • Synthesis of magnesium-lanthanum deposits by an electrodeposition process. • Voltage effect is investigated using different physicochemical analysis techniques (EDS, XRD, FTIR and SEM). • The EDS analysis shows the presence of three major elements (Mg, La and O) and a little amount of Cl. • Two phases, namely Mg(OH){sub 2} and La(OH){sub 3} are

  9. Impact of Annealing Temperature on the Physical Properties of the Lanthanum Deficiency Manganites

    Directory of Open Access Journals (Sweden)

    Skini Ridha

    2017-10-01

    Full Text Available The lanthanum deficiency manganites La0.8-x□xCa0.2MnO3 (x = 0, 0.1 and 0.2, where □ is a lanthanum vacancy, were prepared using the classic ceramic methods with different thermal treatments (1373 K and 973 K. The structural, magnetic, and magnetocaloric properties of these compounds were studied as a function of annealing temperature. It was noted that the annealing temperature did not affect the crystal structure of our samples (orthorhombic structure with Pnma space group. Nevertheless, a change in the variation of the unit cell volume V, the average bond length dMn–O, and the average bond angles θMn–O–Mn were observed. Magnetization versus temperature study has shown that all samples exhibited a magnetic transition from ferromagnetic (FM to paramagnetic (PM phase with increasing temperature. However, it can be clearly seen that the annealing at 973 K induced an increase of the magnetization. In addition, the magnetocaloric effect (MCE as well as the relative cooling power (RCP were estimated. As an important result, the values of MCE and RCP in our Lanthanum-deficiency manganites are reported to be near to those found in gadolinium, considered as magnetocaloric reference material.

  10. Modification of TiO2 nanoparticles through lanthanum doping and PEG templating

    Directory of Open Access Journals (Sweden)

    Marija Milanovic

    2014-12-01

    Full Text Available Pure and lanthanum doped titania nanopowders were synthesized through a room temperature sol-gel method using a template of polyethylene glycol (PEG. The progress of the synthesis in terms of phase formation and size of nanoparticles was monitored by X-ray diffraction, FTIR spectroscopy and SEM analysis. After calcination at 450 °C in air, the results have shown the presence of small particles crystallized predominantly in the form of anatase phase, with significant agglomeration. Nitrogen adsorption-desorption measurements confirmed that all prepared powders are mesoporous with an average pore diameter in range 3.1–3.8 nm. The addition of lanthanum ions leads to the nanopowders with the highest specific surface (BET area (203 m2/g. The obtained powders were compared to TiO2 prepared without a template.

  11. Lanthanum and yttrium oxysulfides activated by europium: (Ln1-x Eux)2 O2 S - Synthesis and characterization

    International Nuclear Information System (INIS)

    Luiz, J.M.

    1989-01-01

    The synthesis of lanthanum and yttrium oxysulfides activated by europium were obtained by thermal decomposition of lanthanum and yttrium oxalates doped with europium, under an argon and sulphur atmosphere. The thermal decomposition of these compounds is studied by differential thermal analysis (DTA). The characterization of these oxysulfides were made by chemical analyses, infrared spectroscopy, X-ray diffraction, scanning electron microscopy and emission spectroscopy. (M.V.M.)

  12. Molecular absorption spectra of beryllium, cerium, lanthanum, iron, and platinum salts

    International Nuclear Information System (INIS)

    Daidoji, Hidehiro

    1980-01-01

    The absorption spectra of some salts of beryllium, cerium, lanthanum, iron and platinum in air-acetylene flame were measured in the wavelength range from 200 to 400 nm. A Hitachi 207 type atomic absorption spectrophotometer was used. A deuterium lamp, a home-made continuous radiation lamp and some hollow cathode lamps were used as light sources. The new molecular absorption spectra of cerium, lanthanum and platinum and the absorption spectra due to Be(OH) 2 , LaO, PtH, FeO and FeCl in 200-400 nm region were obtained. Emission spectra of CeO, LaO and FeOH were also obtained. These molecular absorption bands were estimated as absorption errors of maximum 15 times to the sensitivity of each elements in atomic absorption spectrometry. In addition, spectral line interferences of iron were observed in atomic absorption spectrometry of Zn, Cd, Ni, Cu and Cr. (author)

  13. The combination of lanthanum chloride and the calcimimetic calindol delays the progression of vascular smooth muscle cells calcification

    Energy Technology Data Exchange (ETDEWEB)

    Ciceri, Paola; Volpi, Elisa; Brenna, Irene; Elli, Francesca [Renal Division and Laboratory of Experimental Nephrology, Dipartimento di Medicina e Chirurgia, Universita di Milano, Milan (Italy); Borghi, Elisa [Dipartimento di Salute Pubblica, Microbiologia e Virologia, Universita di Milano, Milan (Italy); Brancaccio, Diego [Renal Division and Laboratory of Experimental Nephrology, Dipartimento di Medicina e Chirurgia, Universita di Milano, Milan (Italy); Cozzolino, Mario, E-mail: mario.cozzolino@unimi.it [Renal Division and Laboratory of Experimental Nephrology, Dipartimento di Medicina e Chirurgia, Universita di Milano, Milan (Italy)

    2012-02-24

    Highlights: Black-Right-Pointing-Pointer Lanthanum reduces the progression of high phosphate-induced calcium deposition. Black-Right-Pointing-Pointer Calcium receptor agonists and the calcimimetic calindol reduce calcium deposition. Black-Right-Pointing-Pointer Lanthanum and calindol cooperate on reducing calcium deposition. Black-Right-Pointing-Pointer Lanthanum and calindol may interact with the same receptor. -- Abstract: Phosphate (Pi)-binders are commonly used in dialysis patients to control high Pi levels, that associated with vascular calcification (VC). The aim of this study was to investigate the effects of lanthanum chloride (LaCl{sub 3}) on the progression of high Pi-induced VC, in rat vascular smooth muscle cells (VSMCs). Pi-induced Ca deposition was inhibited by LaCl{sub 3}, with a maximal effect at 100 {mu}M (59.0 {+-} 2.5% inhibition). Furthermore, we studied the effects on VC of calcium sensing receptor (CaSR) agonists. Gadolinium chloride, neomycin, spermine, and the calcimimetic calindol significantly inhibited Pi-induced VC (55.9 {+-} 2.2%, 37.3 {+-} 4.7%, 30.2 {+-} 5.7%, and 63.8 {+-} 5.7%, respectively). To investigate the hypothesis that LaCl{sub 3} reduces the progression of VC by interacting with the CaSR, we performed a concentration-response curve of LaCl{sub 3} in presence of a sub-effective concentration of calindol (10 nM). Interestingly, this curve was shifted to the left (IC{sub 50} 9.6 {+-} 2.6 {mu}M), compared to the curve in the presence of LaCl{sub 3} alone (IC{sub 50} 19.0 {+-} 4.8 {mu}M). In conclusion, we demonstrated that lanthanum chloride effectively reduces the progression of high phosphate-induced vascular calcification. In addition, LaCl{sub 3} cooperates with the calcimimetic calindol in decreasing Ca deposition in this in vitro model. These results suggest the potential role of lanthanum in the treatment of VC induced by high Pi.

  14. Spectral studies of lanthanide-nucleic acid component interaction: complexes of adenine, adenosine, adenosine 5'-mono-, adenosine 5'-di- and adenosine 5' tri-phosphates with praseodymium(III)

    International Nuclear Information System (INIS)

    Joseph, George; Anjaiah, K.; Misra, S.N.

    1990-01-01

    The interactions of adenine, adenosine, adenosine 5'-mono-, adenosine 5'-di-and adenosine 5'-tri-phosphates with praseodymium(III) have been studied in different stoichiometries and at varying hydrogen ion concentrations by absorption spectral studies. The sharp bands in the spectra have been individually analysed by Gaussian curve analysis, and various spectral parameters have been computed using partial and multiple regression methods on an HP-1000/45 computer. The changes in and the magnitudes of these parameters have been correlated with the degrees of outer- and inner-sphere coordination around praseodymium(III). Crystalline complexes of the type: Pr(nucleotide) 2 (H 2 O) 2 (where nucleotide = AMP, ADP and ATP) have been characterized on the basis of analytical, IR and 1 H NMR spectral data. These studies indicate that the binding of the nucleotide is through phosphoric oxygen. These complexes in aqueous medium show significant ionization which supports the observed weak 4f-4f bands, lower values of nephelauxetic effect and the parameters derived from coulombic and spin-orbit interactions. (author). 3 t abs., 28 refs

  15. Effects of adding lanthanum to Ni/ZrO2 catalysts on ethanol steam reforming

    International Nuclear Information System (INIS)

    Profeti, Luciene Paula Roberto; Habitzheuter, Filipe; Assaf, Elisabete Moreira

    2012-01-01

    The catalytic performance of Ni/ZrO 2 catalysts loaded with different lanthanum content for steam reforming of ethanol was investigated. Catalysts were characterized by BET surface area, X-ray diffraction, UV-vis spectroscopy, temperature programmed reduction, and X-ray absorption fine structure techniques. Results showed that lanthanum addition led to an increase in the degree of reduction of both NiO and nickel surface species interacting with the support, due to the higher dispersion effect. The best catalytic performance at 450 deg C was found for the Ni/12LZ catalyst, which exhibited an effluent gaseous mixture with the highest H 2 yield. (author)

  16. Growth and physico chemical characterization of lanthanum neodymium oxalate single crystals

    International Nuclear Information System (INIS)

    Raju, K.S.; John, Varughese; Ittyachen, M.A.

    1998-01-01

    Single crystals of lanthanum neodymium oxalate (LNO) are grown in sodium meta silicate gels, by the diffusion of a mixture of aqueous solutions of lanthanum nitrate and neodymium nitrate into the test tube having the set gel containing oxalic acid. The bluish pink coloured tabular crystals of LNO having well defined hexagonal basal planes appear either as foggy or clear, the latter at the greater depths inside the gel. The coloration of LNO visually observed is evidenced in UV-visible spectrum, by the revelation of well pronounced characteristic peaks in the visible region (500-900 nm). X-ray diffraction (XRD) of powdered LNO is ordered, meaning crystalline in nature, besides its isostructurality with similarly grown lanthanum samarium oxalate crystals. The single crystallinity of LNO is established by its oscillation XRD pattern. Thermogravimetric analysis (TGA) and differential scanning colorimetry (DSC) support that LNO loses water of crystallization around 120 degC and CO and CO 2 around 350-450 degC, while the infrared absorption (IR) spectrum of LNO establishes the presence of oxalate (C 2 O 4 ) 2- ions. Energy dispersive x-ray analysis (EDAX) confirms the presence of La and Nd in the sample. X-ray photoelectron spectroscopic (XPS) studies of LNO establish the presence of La and Nd in their respective oxide states. An empirical structure for LNO has been proposed on the basis of these findings. The smokiness in the foggy LNO crystal has been attributed due to the gel inclusion during the growth process. (author)

  17. Growth and scintillation properties of praseodymium doped (Lu,Gd).sub.3./sub.(Ga,Al).sub.5./sub.O.sub.12./sub. single crystals

    Czech Academy of Sciences Publication Activity Database

    Kamada, K.; Nikl, Martin; Kurosawa, S.; Shoji, Y.; Pejchal, Jan; Ohashi, Y.; Yokota, Y.; Yoshikawa, A.

    2016-01-01

    Roč. 169, Jan (2016), s. 811-815 ISSN 0022-2313. [International Conference on Luminescence and Optical Spectroscopy of Condensed Matter /17./. Wroclaw, 13.07.2014-18.07.2014] R&D Projects: GA MŠk(CZ) LH14266 EU Projects: European Commission(XE) 316906 - LUMINET Institutional support: RVO:68378271 Keywords : single crystal growth * oxides * scintillators * praseodymium * garnet Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.686, year: 2016

  18. Microwave-assisted Weak Acid Hydrolysis of Proteins

    Directory of Open Access Journals (Sweden)

    Miyeong Seo

    2012-06-01

    Full Text Available Myoglobin was hydrolyzed by microwave-assisted weak acid hydrolysis with 2% formic acid at 37 oC, 50 oC, and100 oC for 1 h. The most effective hydrolysis was observed at 100 oC. Hydrolysis products were investigated using matrixassistedlaser desorption/ionization time-of-flight mass spectrometry. Most cleavages predominantly occurred at the C-termini ofaspartyl residues. For comparison, weak acid hydrolysis was also performed in boiling water for 20, 40, 60, and 120 min. A 60-min weak acid hydrolysis in boiling water yielded similar results as a 60-min microwave-assisted weak acid hydrolysis at100 oC. These results strongly suggest that microwave irradiation has no notable enhancement effect on acid hydrolysis of proteinsand that temperature is the major factor that determines the effectiveness of weak acid hydrolysis.

  19. Synthesis and Characterization of Lanthanum Complexes with Amino Acid Schiff Base

    Institute of Scientific and Technical Information of China (English)

    张秀英; 张有娟; 杨林

    2001-01-01

    Six new complexes of lanthanum with amino acid Schiff base ligands, A-F, were prepared in methanol-aqueous solution. The composition and properties of the title complexes were characterized by elemental analysis, molar conductance, infrared, electronic spectra, 1H NMR, thermogravimetric and differential thermal analysis.

  20. Effect of long-term intake of lanthanum chloride on the concentrations of some macro- and trace elements in rat brains using NAA

    International Nuclear Information System (INIS)

    Yu Tong; Li Yaming; Ren Yan; Wang Enbo; Xu Hongying; Wang Wenzhong

    2005-01-01

    Effects of long-term intake of lanthanum in drinking water on the concentrations of twelve kinds of macro- and trace elements in rat brains were primarily studied by neutron activation analysis. The results show that, along with the elevation of the dose of lanthanum, more and more elements were affected in the rat brain tissues. Compared with control group, the concentrations of five elements were changed in the 1000 mg/L group. These elements have close relations with brain function. Accordingly, intake of lanthanum may have negative effects on brain function. (authors)

  1. Separation of lanthanum from samarium on solid aluminum electrode in LiCl-KCl eutectic melts

    International Nuclear Information System (INIS)

    De-Bin Ji; Mi-Lin Zhang; Xing Li; Xiao-Yan Jing; Wei Han; Yong-De Yan; Yun Xue; Zhi-Jian Zhang; Harbin Engineering University, Harbin

    2015-01-01

    This paper presents an electrochemical study on the separation of lanthanum from samarium on aluminum electrode at 773 K. The results from different electrochemical methods showed that Sm(III) and La(III) formed Al-Sm and Al-La intermetallic compounds on an aluminum electrode at electrode potential around -1.67 and -1.46 V, respectively. The electrochemical separation of lanthanum was carried out in LiCl-KCl-LaCl 3 -SmCl 3 melts on solid aluminum electrodes at 773 K by potentiostatic electrolysis at -1.45 V for 40 h and the separation efficiency was 99.1 %. (author)

  2. Effect of lanthanum substitution on dielectric relaxation, impedance response, conducting and magnetic properties of strontium hexaferrite

    Energy Technology Data Exchange (ETDEWEB)

    Want, Basharat, E-mail: bawant@kashmiruniversity.ac.in; Bhat, Bilal Hamid; Ahmad, Bhat Zahoor

    2015-04-05

    Highlights: • The substitution of La affects the dielectric and magnetic properties of strontium hexaferrite. • The electric behaviour of the compound follows the Koop’s phenomenological theory. • The impedance study shows the role of grain boundaries to the electric properties of the compound. • The substitution of La to strontium hexaferrite reduces the resistive nature of grain boundaries. - Abstract: Lanthanum strontium hexaferrite Sr{sub 1−x}La{sub x}Fe{sub 12}O{sub 19} (x = 0, 0.08, 0.13 , 0.18) has been successfully synthesized by using citrate-precursor method and characterized by different techniques. The X-ray diffraction results revealed that the sample is crystalline in nature and is of single phase with the space group P63/mmc. The dielectric, conducting and impedance related studies have been carried out as a function of frequency and concentration of lanthanum in the frequency ranges of 20 Hz–3 MHz. Impedance studies were performed in the frequency domain to distinguish between bulk and grain boundary contributions of the material to the overall dielectric response. The electric response of the material was also modeled by an equivalent circuit and different circuit parameters were calculated. Magnetic characterization of the material was also performed and the effect of lanthanum concentration was studied. The hysteresis loop obtained from the magnetometer showed that with the increase of lanthanum concentration, the saturation magnetisation decreases while as coercivity increases.

  3. Studies on the lanthanum arsenate ion-exchanger: preparation, physicochemical properties and applications

    International Nuclear Information System (INIS)

    Mukherjee, A.K.; Mandal, S.K.

    1984-01-01

    The cation-exchange behaviour of lanthanum arsenate has been studied. This paper reports the preparation and physicochemical properties of the exchanger. Its analytical utility is compared with that of other arsenate exchangers. Some practical analytical applications are described. (author)

  4. Mechanical and Thermal Properties of Praseodymium Monopnictides: AN Ultrasonic Study

    Science.gov (United States)

    Bhalla, Vyoma; Kumar, Raj; Tripathy, Chinmayee; Singh, Devraj

    2013-09-01

    We have computed ultrasonic attenuation, acoustic coupling constants and ultrasonic velocities of praseodymium monopnictides PrX(X: N, P, As, Sb and Bi) along the , , in the temperature range 100-500 K using higher order elastic constants. The higher order elastic constants are evaluated using Coulomb and Born-Mayer potential with two basic parameters viz. nearest-neighbor distance and hardness parameter in the temperature range of 0-500 K. Several other mechanical and thermal parameters like bulk modulus, shear modulus, Young's modulus, Poisson ratio, anisotropic ratio, tetragonal moduli, Breazeale's nonlinearity parameter and Debye temperature are also calculated. In the present study, the fracture/toughness (B/G) ratio is less than 1.75 which implies that PrX compounds are brittle in nature at room temperature. The chosen material fulfilled Born criterion of mechanical stability. We also found the deviation of Cauchy's relation at higher temperatures. PrN is most stable material as it has highest valued higher order elastic constants as well as the ultrasonic velocity. Further, the lattice thermal conductivity using modified approach of Slack and Berman is determined at room temperature. The ultrasonic attenuation due to phonon-phonon interaction and thermoelastic relaxation mechanisms have been computed using modified Mason's approach. The results with other well-known physical properties are useful for industrial applications.

  5. REM effect on nonmetallic inclusion composition and heat resistance in an austenitic steel

    International Nuclear Information System (INIS)

    Farafonov, V.K.; Shtejnberg, M.M.; Kikhtin, M.V.; Cheremnykh, V.P.; Vojnov, V.V.

    1979-01-01

    Studies were made to elucidate the effect of rare earths (lanthanum, neodymium, praseodymium, cerium) on the composition of non-metallic inclusions and heat resistance of an austenitic chromium-nickel steel. Common sulfide and oxide inclusions are shown to be substituted by rare earth sulfide and oxide inclusions at RE metal content in the steel up to 0.1%. Further increase of RE metal content results in increasing non-metallic inclusions containing RE metals, phosphorus and non-ferrous impurities. Creep rate changes insignificantly at RE metal content up to 0.1%, and then it sharply grows with the quantity of non-metallic inclusions in the steel

  6. Techniques of laser spectroscopy in investigations of lanthanides' free atoms and ions

    International Nuclear Information System (INIS)

    Furmann, B.; Szawiola, G.; Jarosz, A.; Krzykowski, A.; Stefanska, D.; Dembczynski, J.

    2010-01-01

    Various experimental methods, used in Chair of Quantum Engineering and Metrology for determination of the hyperfine structure of electronic levels in lanthanides atoms and ions, are presented. In turn the spectroscopic methods on an atomic beam (laser induced fluorescence and laser-rf double resonance ABMR-LIRF), laser-rf double resonance in a Paul trap and spectroscopic methods in a hollow cathode discharge (optogalvanic detection and laser induced fluorescence) are presented. Each method has been characterized with its potential accuracy and domain of application. The results achieved for the atoms and the ions of lanthanum, praseodymium, neodymium and europium have been published in numerous articles (compiled in the reference list).

  7. Study of the solubility of yttrium, praseodymium, neodymium, and gadolinium sulfates in the presence of sodium and potassium in sulfuric-phosphoric acid solutions at 20 deg C

    International Nuclear Information System (INIS)

    Lokshin, Eh.P.; Tareeva, O.A.; Kashulina, T.G.

    2007-01-01

    The solubility of yttrium, praseodymium, neodymium, and gadolinium sulfates in the presence of sodium and potassium ions and the composition of solid phases were studied at 20 deg C in relation to the concentration of acids in sulfuric acid, phosphoric acid, and sulfuric-phosphoric acid solutions containing up to 36 wt % H 2 SO 4 and 33.12 g 1 -1 H 3 PO 4 . The formation of double sulfates of praseodymium and neodymium with sodium and potassium ions, as well as of gadolinium sulfate with sodium ions of the composition 1 : 1 was revealed. In water at 20 deg C, the solubility products of PrNa(SO 4 ) 2 ·H 2 O, NdNa(SO 4 ) 2 ·H 2 O, GdNa(SO 4 ) 2 ·H 2 O, PrK(SO 4 ) 2 ·H 2 O, and NdK(SO 4 ) 2 ·H 2 O are found to be 7.28x10 -8 , 7.84x10 -8 , 3.09x10 -6 , 3.02x10 -6 , and 1.70x10 -6 , respectively [ru

  8. Development of a 1 kW Class SOFC Stack using Doped Lanthanum Gallate

    Energy Technology Data Exchange (ETDEWEB)

    Akikusa, J.; Adachi, K.; Yamada, T.; Akbay, T.; Murakami, N.; Chitose, N.; Hoshino, K.; Hosoi, K.; Yoshida, H.; Sasaki, T.; Inagaki, T.; Ishihara, T.; Takita, Y.

    2002-06-01

    The performance of lanthanum gallate based SOFC has been investigated as a high-energy conversion device. A planar type SOFC which could operate at temperatures below 800 {sup o}C has been jointly developed. As an electrolyte material, lanthanum gallate (LaGaO{sub 3}) with substitutions of Sr for the La site and Mg and Co for the Ga site (LSGMC) was used. The synthesis technique for large-sized cell production has been established, and the performance of a self- supported diameter 154 mm cell with 200 {mu}m electrolyte thickness is investigated. The output power of 50 W has been obtained with a conversion efficiency [LHV] of 45 % for a single cell. In addition, a metallic separator made of stainless steel was chosen and tested successfully for a seal-less stack. The output power of 1 kW by means of the stack of 18 cells has been achieved for the first time utilizing lanthanum gallate. Moreover, NiO-SDC composite powders were prepared by the spray pyrolysis method and used for the anode on 100 {mu}m thickness LSGMC electrolyte with a combination of samarium cobaltite for the cathode. The power density of as high as 1.8 W/cm{sup 2} at 0.7 V terminal voltage was achieved at 800{sup o}C. (author)

  9. Materials system for intermediate temperature solid oxide fuel cells based on doped lanthanum-gallate electrolyte

    Science.gov (United States)

    Gong, Wenquan

    2005-07-01

    The objective of this work was to identify a materials system for intermediate temperature solid oxide fuel cells (IT-SOFCs). Towards this goal, alternating current complex impedance spectroscopy was employed as a tool to study electrode polarization effects in symmetrical cells employing strontium and magnesium doped lanthanum gallate (LSGM) electrolyte. Several cathode materials were investigated including strontium doped lanthanum manganite (LSM), Strontium and iron doped lanthanum cobaltate (LSCF), LSM-LSGM, and LSCF-LSGM composites. Investigated Anode materials included nickel-gadolinium or lanthanum doped cerium oxide (Ni-GDC, or Ni-LDC) composites. The ohmic and the polarization resistances of the symmetrical cells were obtained as a function of temperature, time, thickness, and the composition of the electrodes. Based on these studies, the single phase LSM electrode had the highest polarization resistance among the cathode materials. The mixed-conducting LSCF electrode had polarization resistance orders of magnitude lower than that of the LSM-LSGM composite electrodes. Although incorporating LSGM in the LSCF electrode did not reduce the cell polarization resistance significantly, it could reduce the thermal expansion coefficient mismatch between the LSCF electrodes and LSGM electrolyte. Moreover, the polarization resistance of the LSCF electrode decreased asymptotically as the electrode thickness was increased thus suggesting that the electrode thickness needed not be thicker than this asymptotic limit. On the anode side of the IT-SOFC, Ni reacted with LSGM electrolyte, and lanthanum diffusion occurred from the LSGM electrolyte to the GDC barrier layer, which was between the LSGM electrolyte and the Ni-composite anode. However, LDC served as an effective barrier layer. Ni-LDC (70 v% Ni) anode had the largest polarization resistance, while all other anode materials, i.e. Ni-LDC (50 v% Ni), Ni-GDC (70 v% NO, and Ni-GDC (50 v% Ni), had similar polarization

  10. Nanostructured Lanthanum Halides and CeBr3 for Nuclear Radiation and Detection

    International Nuclear Information System (INIS)

    Guss, Paul; Mukhopadhyay, Sanjoy; Guise, Ron; Yuan, Ding

    2010-01-01

    Scintillator materials are used to detect, and in some cases identify, gamma rays. Higher performance scintillators are expensive, hard to manufacture, fragile, and sometimes require liquid nitrogen or cooling engines. But whereas lower-quality scintillators are cheap, easy to manufacture, and more rugged, their performance is lower. At issue: can the desirable qualities of high-and low-performance scintillators be combined to achieve better performance at lower cost? Preliminary experiments show that a LaF 3 :Ce oleic acid-based nanocomposite exhibits a photopeak when exposed to 137 Cs source gamma-radiation. The chemical synthesis of the cerium-doped lanthanum halide nanoparticles are scalable and large quantities of material can be produced at a time, unlike typical crystal growth processes such as the Bridgeman process. Using a polymer composite (Figure 1), produced by LANL, initial measurements of the unloaded and 8% LaF 3 :Ce-loaded sample have been made using 137 Cs sources. Figure 2 shows an energy spectrum acquired for CeF 3 . The lighter plot is the measured polymer-only spectrum and the black plot is the spectrum from the nanocomposite scintillator. As the development of this material continues, the energy resolution is expected to improve and the photopeak-to-Compton ratio will become greater at higher loadings. These measurements show the expected Compton edge in the polymer-only sample, and the Compton edge and photo-peak expected in the nanophosphor composites that LANL has produced. Using a porous VYCORR with CdSe/ZnS core shell quantum dots, Letant has demonstrated that he has obtained signatures of the 241Am photopeak with energy resolution as good at NaI (Figure 3). We begin with the fact that CeBr 3 crystals do not have a self-activity component as strong as the lanthanum halides. The radioactive 0.090% 138 La component of lanthanum leads to significant self-activity, which will be a problem for very large detector volumes. Yet a significant

  11. Lanthanum (samarium) nitrate-4-aminoantipyrine nitrate-water systems

    International Nuclear Information System (INIS)

    Starikova, L.I.; Zhuravlev, E.F.

    1985-01-01

    Using the isothermal method of cross-sections at 50 deg C systems lanthanum nitrate-4-aminoantipyrine nitrate-water (1), samarium nitrate-4-aminoantipyrine nitrate-water (2), are studied. Isotherms of system 1 consist of two crystallization branches of initial salt components. In system 2 formation of congruently soluble compounds of the composition Sm(No) 3 ) 3 xC 11 H 13 ON 3 xHNO 3 is established. Analytical, X-ray phase and thermogravimetric analysis of the isolated binary salt are carried out

  12. Apparent molar volumes and compressibilities of lanthanum, gadolinium and lutetium trifluoromethanesulfonates in dimethylsulfoxide

    International Nuclear Information System (INIS)

    Warmińska, Dorota; Wawer, Jarosław

    2012-01-01

    Highlights: ► Sequence of volumes and compressibilities of Ln 3+ ions in DMSO is: La 3+ > Gd 3+ 3+ . ► Sequence of the partial molar volumes do not change with temperature. ► These results are the consequence of nature of the ion–solvent bonding. - Abstract: Temperature dependencies of the densities of dimethylsulfoxide solutions of lanthanum, gadolinium and lutetium trifluoromethanesulfonates have been determined over a wide range of concentrations. The apparent molar volumes and partial molar volumes of the salts at infinite dilution, as well as the expansibilities of the salts, have been calculated from density data. Additionally, the apparent molar isentropic compressibilities of lanthanum, gadolinium and lutetium trifluoromethanesulfonates have been calculated from sound velocity data at 298.15 K. The data obtained have been interpreted in terms of ion−solvent interactions.

  13. Enzymic lactose hydrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Miller, J J; Brand, J C

    1980-01-01

    Acid or enzymic hydrolysis can be used to hydrolyze lactose. Advantages of both are compared and details of enzymic hydrolysis using yeast or fungal enzymes given. The new scheme outlined involves recycling lactase. Because lactose and lactase react to ultrafiltration (UF) membranes differently separation is possible. Milk or milk products are ultrafiltered to separate a concentrate from a lactose-rich permeate which is treated with lactase in a reactor until hydrolysis reaches a required level. The lactase can be removed by UF as it does not permeate the membrane, and it is recycled back to the reactor. Permeate from the second UF stage may or may not be recombined with the concentrate from the first stage to produce a low lactose product (analysis of a typical low-lactose dried whole milk is given). Batch or continuous processes are explained and a batch process without enzyme recovery is discussed. (Refs. 4).

  14. Effect of various lanthanum sol-gel coatings on the 330Cb (Fe-35Ni-18Cr-1Nb-2Si) oxidation at 900 deg. C

    Energy Technology Data Exchange (ETDEWEB)

    Buscail, H., E-mail: buscail@iut.u-clermont1.fr [Clermont Universite- LVEEM, 8 rue J.B. Fabre, BP 219, 43006 Le Puy en Velay (France); Issartel, C.; Riffard, F.; Rolland, R.; Perrier, S. [Clermont Universite- LVEEM, 8 rue J.B. Fabre, BP 219, 43006 Le Puy en Velay (France); Fleurentin, A. [CETIM, 52 av Felix Louat, BP 80067, 60304 Senlis (France); Josse, C. [L' ICB UMR5209 CNRS, BP 47870, 21078 Dijon (France)

    2011-11-01

    The influence of a lanthanum sol-gel coating on the oxide scale adherence has been studied during the 330Cb (Fe-35Ni-18Cr-1Nb-2Si) oxidation at 900 deg. C, in air. The alloy oxidation is performed in order to generate a protective chromia scale acting as a good barrier against carburization. Argon annealing of lanthanum sol-gel coatings have been performed at various temperatures in order to find the best conditions to insure the scale adherence. Kinetic results show that lanthanum sol-gel coatings lead to a lower oxidation rate compared to blank specimens. Thermal cycling tests on lanthanum the sol-gel coated specimen show that the oxide scale formed at 900 deg. C, in air, is adherent.

  15. Effect of gelatinization and hydrolysis conditions on the selectivity of starch hydrolysis with alpha-amylase from Bacillus licheniformis

    NARCIS (Netherlands)

    Baks, T.; Bruins, M.E.; Matser, A.M.; Janssen, A.E.M.; Boom, R.M.

    2008-01-01

    Enzymatic hydrolysis of starch can be used to obtain various valuable hydrolyzates with different compositions. The effects of starch pretreatment, enzyme addition point, and hydrolysis conditions on the hydrolyzate composition and reaction rate during wheat starch hydrolysis with ¿-amylase from

  16. Hydrocarbon conversion with cracking catalyst having co-combustion promoters lanthanum and iron

    International Nuclear Information System (INIS)

    Csicsery, S.M.

    1979-01-01

    A composition useful in hydrocarbon conversion processes such as catalytic cracking comprises 0.05 to 10 weight percent lanthanum associated with a refractory support. The composition may also include 0.02 to 10 weight percent iron. The refractory support is a zeolitic crystalline aluminosilicate

  17. Paramagnetic resonance of Mn4+ and Mn2+ centers in lanthanum gallate single crystals

    Science.gov (United States)

    Vazhenin, V. A.; Potapov, A. P.; Guseva, V. B.; Artyomov, M. Yu.

    2010-03-01

    An increase in the manganese concentration in lanthanum gallate in the range 0.5-5.0% has been found to result in a complete replacement of individual Mn4+ ions by Mn2+ ions. The relative concentrations and binding energies of individual Mn4+, Mn3+, and Mn2+ ions have been determined. The spin Hamiltonians of the Mn2+ and Mn4+ centers in the rhombohedral and orthorhombic phases, respectively, have been constructed and the orientation of the principal axes of the fine-structure tensor of Mn4+ at room temperature has been found. The possibility of using electron paramagnetic resonance for determining the rotation angles of oxygen octahedra of lanthanum gallate with respect to the perovskite structure has been discussed.

  18. Corrosion of Zn5Al and Zn55Al alloys with cerium, praseodymium and neodymium

    International Nuclear Information System (INIS)

    Alikhanova, S.D.

    2017-01-01

    The present work is devoted to corrosion of Zn5Al and Zn55Al alloys with cerium, praseodymium and neodymium. The purpose of present work is elaboration of optimal composition of zinc-aluminium alloys Zn5Al and Zn55Al alloyed by rare-earth metals of cerium subgroup which are used as anode covers for protection of steel from corrosion. Therefore, the regularities of change of corrosion-electrochemical properties in various corrosive mediums have been determined; processes mechanisms of high temperature oxidation of alloys in solid state have been studied; in the products of alloys oxidation their phase components have been defined and their role in the corrosion process have been revealed; the optimal compositions of zinc-aluminium alloys alloyed by rare earth metals, which are protected by two patents of the Republic of Tajikistan have been elaborated.

  19. Adsorbtion of oxygen and cesium on lanthanum hexaboride

    International Nuclear Information System (INIS)

    Gorodetskij, D.A.; Tskhakaya, V.K.; Shchudlo, Yu.G.; Yarygin, V.I.; Yas'ko, A.A.

    1982-01-01

    Oxygen and cesium adsorption on lanthanum hexaboride was investigated. Especial attention was paid to structural investigations of the LaB 6 (100)-O system. Diffraction pictures and curves of changes in work function in the process of oxygen disorption have been obtained. At oxygen adsorption on a crystal heated up to different temperatures in the range of 900-1400 K the same diffraction pictures as at corresponding annealing temperatures observed were. It is noted that adsorption heat changes slightly in the LaB 6 -O-Cs system

  20. Cation disorder in Ga1212.

    Science.gov (United States)

    Greenwood, K B; Ko, D; Vander Griend, D A; Sarjeant, G M; Milgram, J W; Garrity, E S; DeLoach, D I; Poeppelmeier, K R; Salvador, P A; Mason, T O

    2000-07-24

    Substitution of calcium for strontium in LnSr2-xCaxCu2GaO7 (Ln = La, Pr, Nd, Gd, Ho, Er, Tm, and Yb) materials at ambient pressure and 975 degrees C results in complete substitution of calcium for strontium in the lanthanum and praseodymium systems and partial substitution in the other lanthanide systems. The calcium saturation level depends on the size of the Ln cation, and in all cases, a decrease in the lattice parameters with calcium concentration was observed until a common, lower bound, average A-cation size is reached. Site occupancies from X-ray and neutron diffraction experiments for LnSr2-xCaxCu2GaO7 (x = 0 and x = 2) confirm that the A-cations distribute between the two blocking-layer sites and the active-layer site based on size. A quantitative link between cation distribution and relative site-specific cation enthalpy for calcium, strontium, and lanthanum within the gallate structure is derived. The cation distribution in other similar materials can potentially be modeled.

  1. Synthesis and characterization of nanoporous strontium-doped lanthanum cobaltite thin film using metal organic chemical solution deposition

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jun-Sik [Department of Mechanical Convergence Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Kim, Young-Beom, E-mail: ybkim@hanyang.ac.kr [Department of Mechanical Convergence Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Institute of Nano Science and Technology, Hanyang University, Seoul 133-791 (Korea, Republic of)

    2016-01-29

    By employing strontium as a dopant of lanthanum cobaltite (LaCoO{sub 3}), strontium-doped lanthanum cobaltite (La{sub 1−x}Sr{sub x}CoO{sub 3−δ}, LSC) thin film was fabricated using a metal organic chemical solution deposition (MOCSD) method. Lanthanum nitrate hexahydrate [La(NO{sub 3}){sub 3}6H{sub 2}O], strontium acetate [Sr(CH{sub 3}COO){sub 2}], and cobalt acetate tetrahydrate [Co(CH{sub 3}COO){sub 2}4H{sub 2}O] were used as precursors. The coating process was performed through a spin coating method on a substrate, which were then heat treated under various temperature conditions. Electrical properties, microstructures, and crystalline structures with respect to sintering temperature were analyzed. According to these analyses, the change in surface morphology, phase shift, and conductive properties were closely related, which could explain their respective behaviors. Furthermore, sintered strontium-doped lanthanum perovskite oxides showed various conductivities according to the amount of dopant. With the molar ratio of strontium that is stoichiometrically equivalent to lanthanum (La{sub 0.5}Sr{sub 0.5}CoO{sub 3−δ}) thin film showed the best conductivity in the sintering temperature range of 650–700 °C, with perovskite phases formed at this temperature condition. As the electrically conductive properties of the thin film are a function of thickness, the films were coated several times to a thickness of approximately 300 nm, with the lowest resistivity (approximately 9.06 × 10{sup −4} Ω cm) observed at the optimized sintering temperature and solution composition. - Highlights: • LSC thin film was fabricated by metal organic chemical solution deposition (MOCSD). • The film shows good agreement on the electrical conductivity of LSC by conventional methods. • The properties of LSC film are influenced by the surface morphology and crystalline phase. • Optimal molar ratio of strontium for the highest conductivity was investigated.

  2. Collinear laser spectroscopy on radioactive praseodymium ions and cadmium ions; Kollineare Laserspektroskopie an radioaktiven Praseodymionen und Cadmiumatomen

    Energy Technology Data Exchange (ETDEWEB)

    Froemmgen, Nadja

    2013-11-21

    Collinear laser spectroscopy is a tool for the model independent determination of spins, charge radii and electromagnetic moments of nuclei in ground and long-lived isomeric states. In the context of this thesis a new offline ion source for high evaporating temperatures and an ion beam analysis system were implemented at the TRIGA-LASER Experiment at the Institute for Nuclear Chemistry at the University of Mainz. The main part of the thesis deals with the determination of the properties of radioactive praseodymium and cadmium isotopes by collinear laser spectroscopy at ISOLDE/CERN. The necessary test measurements for the spectroscopy of praseodymium ions have been conducted with the aforementioned offline ion source at the TRIGA-LASER experiment. The spectroscopy of the praseodymium ions was motivated by the observation of a modulation of the electron capture decay rates of hydrogen-like {sup 140}Pr{sup 58+}. The nuclear magnetic moment of the nucleus is, among others, required for the explanation of the so-called GSI Oscillations and has not been studied experimentally before. Additionally, the determined electron capture decay constant of hydrogen-like {sup 140}Pr{sup 58+} is lower than the one of helium-like {sup 140}Pr{sup 57+}. The explanation of this phenomenon requires a positive magnetic moment. During the experiment at the COLLAPS apparatus the magnetic moments of the neutron-deficient isotopes {sup 135}Pr, {sup 136}Pr and {sup 137}Pr could be determined for the first time. Unfortunately, due to a too low production yield the desired isotope {sup 140}Pr could not be studied.The systematic study of cadmium isotopes was motivated by nuclear physics in the tin region. With Z=48 two protons are missing for the shell closure and the isotopes extend from the magic neutron number N=50 to the magic neutron number N=82. The extracted nuclear properties allow tests of different nuclear models in this region. In this thesis the obtained results of the spectroscopy of

  3. Electrospray ionization mass spectrometry for the hydrolysis complexes of cisplatin : Implications for the hydrolysis process of platinum complexes

    NARCIS (Netherlands)

    Xie, Feifan; Colin, Pieter; Van Bocxlaer, Jan

    Non-enzyme-dependent hydrolysis of the drug cisplatin is important for its mode of action and toxicity. However, up until today, the hydrolysis process of cisplatin is still not completely understood. In the present study, the hydrolysis of cisplatin in an aqueous solution was systematically

  4. Lanthanum carbonate versus placebo for management of hyperphosphatemia in patients undergoing peritoneal dialysis: a subgroup analysis of a phase 2 randomized controlled study of dialysis patients

    Directory of Open Access Journals (Sweden)

    Hutchison Alastair J

    2013-02-01

    Full Text Available Abstract Background This short-term study assessed the efficacy and safety of lanthanum carbonate in the treatment of hyperphosphatemia in dialysis patients; here, we report a prespecified subgroup analysis of patients undergoing peritoneal dialysis. Methods Men and women (n = 39 who had received continuous ambulatory peritoneal dialysis for chronic kidney disease for 6 months or more were enrolled in eight renal medicine departments in the United Kingdom. A 2-week washout period was followed by a 4-week dose-titration phase during which patients received lanthanum carbonate titrated up to 2250 mg/day. This was followed by a 4-week, randomized, placebo-controlled, parallel-group phase during which patients continued to receive either lanthanum carbonate at the titrated dose, or a matched dose of placebo. The main outcome measure was control of serum phosphate levels (1.3-1.8 mmol/l at the end of the parallel-group phase. Results Serum phosphate was controlled in 3/39 (8% patients at the beginning of the dose-titration phase (after washout and in 18/31 (58% patients treated with lanthanum carbonate at its end. After the parallel-group phase, 60% of lanthanum carbonate-treated patients and 10% of those receiving placebo had controlled serum phosphate. There was no difference in mean (95% confidence interval serum phosphate levels between groups at randomization: lanthanum carbonate, 1.57 (1.34-1.81 mmol/l; placebo, 1.58 (1.40-1.76 mmol/l (p = 0.96. However, a difference was seen at the end of the parallel-group phase: lanthanum carbonate, 1.56 (1.33-1.79 mmol/l; placebo, 2.25 (1.81-2.68 mmol/l (p = 0.0015. There were no clinically important changes in nutritional parameters and no serious treatment-related adverse events were recorded. Conclusions At doses up to 2250 mg/day, lanthanum carbonate is well tolerated and controls hyperphosphatemia effectively. Treatment with higher doses of lanthanum carbonate may allow patients undergoing

  5. Photoluminescence properties of cerium oxide nanoparticles as a function of lanthanum content

    International Nuclear Information System (INIS)

    Deus, R.C.; Cortés, J.A.; Ramirez, M.A.; Ponce, M.A.; Andres, J.; Rocha, L.S.R.

    2015-01-01

    Highlights: • CeO 2 nanoparticles were obtained by microwave-hydrothermal method. • Rietveld refinement reveals a cubic structure. • KOH mineralizer agent exhibit weak agglomeration at low temperature and shorter time. - Abstract: The structural and photoluminescent properties at room temperature of CeO 2 and La-doped CeO 2 particles were undertaken. The obtained particles were synthesized by a microwave-assisted hydrothermal method (MAH) under different lanthanum contents. X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Fourier transform Raman (FT-Raman), Ultra-violet spectroscopy (UV–vis) and photoluminescence (PL) measurements were carried out. XRD revealed that the powders are free of secondary phases and crystallize in the cubic structure. Raman data show that increasing La doping content increase oxygen vacancies due to lattice expansion. The UV/vis absorption spectroscopy suggested the presence of intermediate energy levels in the band gap of structurally ordered powders. Lanthanum addition creates oxygen vacancies and shifts the photoluminescence in the low energy range leading to intense PL emission

  6. Structures, stabilities, and electronic properties for rare-earth lanthanum doped gold clusters

    International Nuclear Information System (INIS)

    Zhao, Ya-Ru

    2015-01-01

    The structures, stabilities, and electronic properties of rare-earth lanthanum doped gold La 2 Au n (n = 1-9) and pure gold Au n (n ≤ 11) clusters have been investigated by using density functional theory. The optimized geometries show that the lowest energy structures of La 2 Au n clusters favour the 3D structure at n ≥ 3. The lanthanum atoms can strongly enhance the stabilities of gold clusters and tend to occupy the most highly coordinated position. By analysing the gap, vertical ionization potential, and chemical hardness, it is found that the La 2 Au 6 isomer possesses higher stability for small-sized La 2 Au n clusters (n = 1-9). The charges in the La 2 Au n clusters transfer from La atoms to the Au n host. In addition, Wiberg bond indices analysis reveals that the intensity of different bonds of La 2 Au n clusters exhibits a sequence of La-La bond > La-Au bond > Au-Au bond.

  7. Effect of gelatinization and hydrolysis conditions on the selectivity of starch hydrolysis with alpha-amylase from Bacillus licheniformis.

    Science.gov (United States)

    Baks, Tim; Bruins, Marieke E; Matser, Ariette M; Janssen, Anja E M; Boom, Remko M

    2008-01-23

    Enzymatic hydrolysis of starch can be used to obtain various valuable hydrolyzates with different compositions. The effects of starch pretreatment, enzyme addition point, and hydrolysis conditions on the hydrolyzate composition and reaction rate during wheat starch hydrolysis with alpha-amylase from Bacillus licheniformis were compared. Suspensions of native starch or starch gelatinized at different conditions either with or without enzyme were hydrolyzed. During hydrolysis, the oligosaccharide concentration, the dextrose equivalent, and the enzyme activity were determined. We found that the hydrolyzate composition was affected by the type of starch pretreatment and the enzyme addition point but that it was just minimally affected by the pressure applied during hydrolysis, as long as gelatinization was complete. The differences between hydrolysis of thermally gelatinized, high-pressure gelatinized, and native starch were explained by considering the granule structure and the specific surface area of the granules. These results show that the hydrolyzate composition can be influenced by choosing different process sequences and conditions.

  8. Effects of microtubule mechanics on hydrolysis and catastrophes

    International Nuclear Information System (INIS)

    Müller, N; Kierfeld, J

    2014-01-01

    We introduce a model for microtubule (MT) mechanics containing lateral bonds between dimers in neighboring protofilaments, bending rigidity of dimers, and repulsive interactions between protofilaments modeling steric constraints to investigate the influence of mechanical forces on hydrolysis and catastrophes. We use the allosteric dimer model, where tubulin dimers are characterized by an equilibrium bending angle, which changes from 0 ∘ to 22 ∘ by hydrolysis of a dimer. This also affects the lateral interaction and bending energies and, thus, the mechanical equilibrium state of the MT. As hydrolysis gives rise to conformational changes in dimers, mechanical forces also influence the hydrolysis rates by mechanical energy changes modulating the hydrolysis rate. The interaction via the MT mechanics then gives rise to correlation effects in the hydrolysis dynamics, which have not been taken into account before. Assuming a dominant influence of mechanical energies on hydrolysis rates, we investigate the most probable hydrolysis pathways both for vectorial and random hydrolysis. Investigating the stability with respect to lateral bond rupture, we identify initiation configurations for catastrophes along the hydrolysis pathways and values for a lateral bond rupture force. If we allow for rupturing of lateral bonds between dimers in neighboring protofilaments above this threshold force, our model exhibits avalanche-like catastrophe events. (papers)

  9. Praseodymium - A Competent Dopant for Luminescent Downshifting and Photocatalysis in ZnO Thin Films

    Science.gov (United States)

    Narayanan, Nripasree; Deepak, N. K.

    2018-05-01

    Highly transparent and conducting Zinc oxide (ZnO) thin films doped with Praseodymium (Pr) were deposited on glass substrates by using the spray pyrolysis method. The X-ray diffraction (XRD) analysis revealed the polycrystallinity of the deposited films with a hexagonal wurtzite structure, whereas the energy-dispersive X-ray spectroscopy (EDX) analysis confirmed the incorporation of Pr in the films. The optical energy gap decreased by Pr doping due to the merging of the conduction band with the impurity bands formed within the forbidden gap. The room temperature photoluminescence spectra of the Pr-doped film showed enhancement of visible emission, suggesting efficient luminescent downshifting. The photocatalytic activity of the Pr-doped films is higher than that of undoped films due to the effective suppression of the rapid recombination of the photo-generated electron-hole pairs. The impurity levels formed within the forbidden gap act as efficient luminescent centers and electron traps, which lead to luminescent downshifting and enhanced photocatalytic activity.

  10. Induced assembly and photoluminescence of lanthanum (Tb, Eu, Dy) complexes/ZnO/polyethylene glycol hybrid phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Yan Bing [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China)]. E-mail: byan@tongji.edu.cn; Chen Xi [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China); Wu Jianhua [Department of Chemistry, Tongji University, Siping Road 1239, Shanghai 200092 (China)

    2007-08-31

    Some novel kinds of hybrid phosphors were assembled with lanthanum (Tb, Eu, Dy) complexes (with four kinds of terbium complexes is 2,4-dihydroxybenzonic acid (DHBA), 1,10-phenanthroline (phen), acetylacetone (AA) and nicotinic acid (Nic), respectively) doped ZnO/PEG particles by co-precipitation approach derived from Zn(CH{sub 3}COO){sub 2} (Zn(AC){sub 2}), NaOH, PEG as precursors at room temperature. The characteristic luminescence spectra for f-f transitions of Tb{sup 3+}, Eu{sup 3+}, Dy{sup 3+} were observed. It is worthy to point out that ZnO is the excellent host for lanthanum ions by the assembly of PEG matrices.

  11. Synthesis, spectroscopic characterization, solid state d.c. electrical conductivity and biological studies of some lanthanide(III chloride complexes with a heterocyclic Schiff base ligand

    Directory of Open Access Journals (Sweden)

    K. Mohanan

    2016-07-01

    Full Text Available Condensation of 2-hydroxy-1-naphthaldehyde with 2-amino-3-carboxyethyl-4,5-dimethylthiophene in 1:1 molar ratio, yielded a potentially tridentate Schiff base viz. 2-[N-(2′-hydroxy-1-naphthylideneamino]-3-carboxyethyl-4,5-dimethylthiophene (HNAT. This ligand formed complexes with lanthanum(III, cerium(III, praseodymium(III, neodymium(III, samarium(III, europium(III and gadolinium(III chloride under well defined conditions. These complexes were characterized through elemental analysis, molar conductance, magnetic moment measurements, IR, UV–Vis, FAB mass and 1H NMR spectral studies. Analytical data showed that all the metal complexes exhibited 1:1 metal–ligand ratio. Molar conductance values adequately confirmed the non-electrolytic nature of the metal complexes. The proton NMR spectral observations supplement the IR spectral assignments. The spectral data revealed that the ligand acted as neutral tridentate, coordinating to the metal ion through azomethine nitrogen, ester carbonyl and naphtholate oxygen without deprotonation. The ligand and its lanthanum(III chloride complex were subjected to XRD studies. The lanthanum(III chloride complex has undergone a facile transesterification reaction. The solid state d.c. electrical conductivity of some selected complexes were measured as a function of temperature, indicating the semiconducting nature of the metal complexes. The antimicrobial activities were examined by disk diffusion method against some pathogenic bacterial and fungal species.

  12. Effects of combined flocculant – Lanthanum modified bentonite treatment on aquatic macroinvertebrate fauna

    NARCIS (Netherlands)

    Waajen, G.; Pauwels, M.; Lürling, M.

    2017-01-01

    A low dose flocculant (FeCl3), combined with lanthanum modified bentonite (LMB) as phosphate-binding agent, has been applied for eutrophication management in Lake De Kuil (The Netherlands). After the treatment, the state of the lake shifted from hypertrophic to mesotrophic. Although

  13. Effect of pressure on the magnetic properties of lanthanum manganite

    International Nuclear Information System (INIS)

    Gonchar', L. E.; Leskova, Yu. V.; Nikiforov, A. E.; Kozlenko, D. P.

    2010-01-01

    The crystalline structure of pure lanthanum manganite under external hydrostatic pressure has been studied. The behavior of magnetic properties and nuclear magnetic resonance (NMR) spectra under these conditions is theoretically predicted. It is shown that an increase in the Neel temperature with pressure is not only caused by the general contraction of the crystal, but is also related to certain peculiarities in the baric behavior of the orbital structure.

  14. Uranyl(VI) and lanthanum(III) complexes with functionalized macrocyclic and macroacyclic Schiff bases

    International Nuclear Information System (INIS)

    Aguiari, A.; Brianese, N.; Tamburini, S.; Vigato, P.A.

    1995-01-01

    Acyclic Schiff bases have been prepared by [2 + 1] condensation of 2,6-diformyl-4-chlorophenol and H 2 NCH 2 [CH 2 XCH 2 ] n CH 2 NH 2 (n =3D 0 H 2 -I; X =3D NH, S, O n =3D 1 H 2 -II...H 2 -IV; X =3D 0 n =3D 2 H 2 -V; X =3D 0 n =3D 3 H 2 -VI). The related uranlyl(VI) and lanthanum (III) complexes have bee synthesized by reaction by reaction of the preformed ligands with the appropriate salt or by the template procedure, in the presence of base. No base was employed in the preparation of lanthanum (III) complexes, La(H 2 -II)(NO 3 ) 3 , La(H 2 -IV)(NO 3 ) 3 where the Schiff bases coordinate as neutral chelate ligands. These acyclic complexes have been used for further condensation, and symmetric and asymmetric cyclic complexes have been obtained by their reaction with the polyamines H 2 NCH 2 [CH 2 XCH 2 ]nCH 2 NH 2 or with 4,4'-diaminodibenzo -18-crown-6. By reaction with 4-aminobenzo-15-crown-5 or 2-amino-methyl-15-crown-5, the same acyclic complexes give rise to functionalized complexes bearing crown-ether moieties. Analogously, the acyclic ligand H 3 -IXX, prepared by condensation of 2,6 diformyl-4-chlorophenol and tris(aminoethyl)amine, forms mono and homodinuclear lanthanum (III) complexes, which may undergo further condensation when reacted with primary functionalized amines. (authors). 42 refs., 2 figs., 2 schemes, 1 tab

  15. Near fifty percent sodium substituted lanthanum manganites—A potential magnetic refrigerant for room temperature applications

    Energy Technology Data Exchange (ETDEWEB)

    Sethulakshmi, N.; Anantharaman, M. R., E-mail: mraiyer@yahoo.com [Department of Physics, Cochin University of Science and Technology, Cochin 682022, Kerala (India); Al-Omari, I. A. [Department of Physics, Sultan Qaboos University, PC 123 Muscat, Sultanate of Oman (Oman); Suresh, K. G. [Department of Physics, Indian Institute of Technology Bombay, Powai, Mumbai 400076 (India)

    2014-03-03

    Nearly half of lanthanum sites in lanthanum manganites were substituted with monovalent ion-sodium and the compound possessed distorted orthorhombic structure. Ferromagnetic ordering at 300 K and the magnetic isotherms at different temperature ranges were analyzed for estimating magnetic entropy variation. Magnetic entropy change of 1.5 J·kg{sup −1}·K{sup −1} was observed near 300 K. An appreciable magnetocaloric effect was also observed for a wide range of temperatures near 300 K for small magnetic field variation. Heat capacity was measured for temperatures lower than 300 K and the adiabatic temperature change increases with increase in temperature with a maximum of 0.62 K at 280 K.

  16. Studies on the rare earth complexes with pyridine derivatives and their N-oxide(II) - Synthesis and properties of fluorescent solid complexes of samarium, europium, gadolium and terbium chlorides with 2,2'-bipyridine-N,N'-dioxide

    International Nuclear Information System (INIS)

    Minyu, T.; Ning, T.; Yingli, Z.; Jiyuan, B.

    1985-01-01

    The solid complexes of rare earth nitrates perchlorates and thiocyanates with 2,2'-bipyridine-N,N'-dioxide (bipyO/sub 2/) have been reported. However, the corresponding complexes of other rear earth chlorides have not been investigated except lanthanum, cerium and yttrium. As an extension of our previous work on the synthesis of complexes of praseodymium and neodymium chlorides wiht bipoyO/sub 2/, the authors have now prepared fluorescent solid complexes of samarium, europium, gadolium and terbium chlorides with biphyO/sub 2/, using methanol as a reaction medium. The new synthesized compounds have been identified by means of elemental analysis, infrared spectrometry, conductometry, differential thermal analysis (DTA), thermogravimetry (TG) and X-ray powder diffraction

  17. Enzymatic hydrolysis of pretreated soybean straw

    International Nuclear Information System (INIS)

    Xu Zhong; Wang Qunhui; Jiang Zhaohua; Yang Xuexin; Ji Yongzhen

    2007-01-01

    In order to produce lactic acid, from agricultural residues such as soybean straw, which is a raw material for biodegradable plastic production, it is necessary to decompose the soybean straw into soluble sugars. Enzymatic hydrolysis is one of the methods in common use, while pretreatment is the effective way to increase the hydrolysis rate. The optimal conditions of pretreatment using ammonia and enzymatic hydrolysis of soybean straw were determined. Compared with the untreated straw, cellulose in straw pretreated by ammonia liquor (10%) soaking for 24 h at room temperature increased 70.27%, whereas hemicellulose and lignin in pretreated straw decreased to 41.45% and 30.16%, respectively. The results of infrared spectra (IR), scanning electron microscope (SEM) and X-ray diffraction (XRD) analysis also showed that the structure and the surface of the straw were changed through pretreatment that is in favor of the following enzymatic hydrolysis. maximum enzymatic hydrolysis rate of 51.22% was achieved at a substrate concentration of 5% (w/v) at 50 deg. C and pH 4.8 using cellulase (50 fpu/g of substrate) for 36 h

  18. Muon spin relaxation and rotation studies of the filled skutterudite alloys praseodymium osmium ruthenium antimonide and praseodymium lanthanum osmium antimonide

    Science.gov (United States)

    Shu, Lei

    Some filled skutterudite compounds have recently been found to exhibit very interesting properties. The first Pr-based heavy-fermion superconductor, PrOs4Sb12, is an intriguing material due to the unusual properties of both its normal and superconducting states. Comprehensive muon spin rotation and relaxation studies and magnetic susceptibility measurements, described in this dissertation, have been performed to investigate the microscopic properties of PrOs4Sb12 and its Ru and La doped alloys. The temperature dependence of penetration depth measured in the vortex state of PrOs4Sb12 using transverse-field muon spin rotation (TF-muSR) is weaker than those measured by radiofrequency measurements. A scenario based on two-band superconductivity in PrOs4Sb 12, is proposed to resolve this difference. TF-muSR experiments also suggest the suppression of superfluid density with Ru doping, probably due to impurity scattering. In addition, magnetic susceptibility data as well as analysis of the muSR data in PrOs4Sb12 reveal a nearly linear relation of mu+ Knight shift vs. magnetic susceptibility. This suggests that the muon charge does not affect the crystalline electric field splitting of Pr3+ near neighbors. Additional evidence comes from the fact that the superconducting transition temperature Tc measured from muSR is consistent with the bulk superconducting values. Zero-field muon spin relaxation (ZF-muSR) experiments have been carried out in the Pr(Os1-xRux) 4Sb12 and Pr1-yLayOs 4Sb12 alloy systems to investigate the time-reversal symmetry (TRS) breaking found in an earlier ZF-muSR study of the end compound PrOs 4Sb12. The results from measurements at KEK, Japan, suggest that Ru doping is considerably more efficient than La doping in suppressing TRS breaking superconducting in PrOs4Sb12. However, we think that the spontaneous local field that indicates TRS breaking detected by ZF-muSR may depend on sample quality if those fields are from inhomogeneity in the superconducting order parameter, since our ZF-muSR experiment detects nonzero spontaneous fields for Pr(Os0.9Ru0.1)4 Sb12 from measurement at ISIS, United Kingdom in different samples. Longitudinal-field muon spin relaxation experiments also have been carried out to elucidate the anomalous dynamic muon spin relaxation detected by ZF-muSR in those alloys. The dynamic muon relaxation found in the alloys appears to be due to 141Pr nuclear spin fluctuations, where the 141Pr moments are enhanced by hyperfine coupling to the Pr 3+ Van Vleck susceptibility.

  19. Method of producing a solution of radioactive lanthanum-140 from radioactive barium-140 in an isotope generator and installation to carry out the method

    International Nuclear Information System (INIS)

    Akerman, K.; Jacobs, G.; Sauerwein, K.

    1979-01-01

    A method of separating radioactive lanthanum-140 from radioactive Ba-140 is proposed. The lanthanum-140 will be washed out of a sulphate precipitate and separated from Ba-140-sulphate by a granular filter mass of CaSO 4 and BaSO 4 . Details of the process are given. (UWI) [de

  20. Hydrolysis Batteries: Generating Electrical Energy during Hydrogen Absorption.

    Science.gov (United States)

    Xiao, Rui; Chen, Jun; Fu, Kai; Zheng, Xinyao; Wang, Teng; Zheng, Jie; Li, Xingguo

    2018-02-19

    The hydrolysis reaction of aluminum can be decoupled into a battery by pairing an Al foil with a Pd-capped yttrium dihydride (YH 2 -Pd) electrode. This hydrolysis battery generates a voltage around 0.45 V and leads to hydrogen absorption into the YH 2 layer. This represents a new hydrogen absorption mechanism featuring electrical energy generation during hydrogen absorption. The hydrolysis battery converts 8-15 % of the thermal energy of the hydrolysis reaction into usable electrical energy, leading to much higher energy efficiency compared to that of direct hydrolysis. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Investigation of lanthanum- and neodymium ion interaction with potassium polyphosphate in aqueous solution

    International Nuclear Information System (INIS)

    Ezhova, Zh.A.; Tananaev, I.V.; Koval', E.M.

    1983-01-01

    A study was made on the interaction in the LaCl 3 -KPO 3 -H 2 O and NdCl 3 -KPO 3 -H 2 O systems at 0 deg C by methods of solubility of residual concentrations and measurement of the pH value. The formation of binary KLa 2 (PO 3 ) 7 x10H 2 O and KLa(PO 3 ) 4 X5H 2 O lanthanum- and potassium polyphosphates, as well as KNd 2 (PO 3 ) 7 X10H 2 O and KNd(PO 3 ) 4 X5H 2 O neodymium- apd potassiUm polyphasphates was established. Chemical, paper-chromatographic, infrared spectroscopic, X-ray diffraction and differential thermal analyses of the prepared compoUnds were conducted. Anhydrous binary lanthanum- and neodymium polyphosphates with potassium-=Kla(PO 3 ) 4 , KNd(PO 3 ) 4 , KLa 2 (PO 3 ) 7 and KNd 2 x(PO 3 ) 7 - eere prepared

  2. Photoluminescence properties of cerium oxide nanoparticles as a function of lanthanum content

    Energy Technology Data Exchange (ETDEWEB)

    Deus, R.C. [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); Cortés, J.A., E-mail: leandrosrr89@gmail.com [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); Ramirez, M.A. [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); Ponce, M.A. [Instituto de Investigaciones en Ciencia y Tecnología de Materiales (INTEMA) (CONICET-Universidad Nacional de Mar del Plata), Juan B. Justo 4302, 7600 Mar del Plata (Argentina); Andres, J. [Laboratório Interdisciplinar em Cerâmica, Instituto de Química, Universidade Estadual Paulista, P.O. Box 355, 14801-907 Araraquara, São Paulo (Brazil); Rocha, L.S.R. [Universidade Estadual Paulista, Unesp —Faculdade de Engenharia de Guaratinguetá, Av. Dr Ariberto Pereira da Cunha 333, Bairro Pedregulho, P.O. Box 355, 12.516-410 Guaratinguetá, São Paulo, Brazil, (Brazil); and others

    2015-10-15

    Highlights: • CeO{sub 2} nanoparticles were obtained by microwave-hydrothermal method. • Rietveld refinement reveals a cubic structure. • KOH mineralizer agent exhibit weak agglomeration at low temperature and shorter time. - Abstract: The structural and photoluminescent properties at room temperature of CeO{sub 2} and La-doped CeO{sub 2} particles were undertaken. The obtained particles were synthesized by a microwave-assisted hydrothermal method (MAH) under different lanthanum contents. X-ray diffraction (XRD), Fourier transform infrared (FT-IR), Fourier transform Raman (FT-Raman), Ultra-violet spectroscopy (UV–vis) and photoluminescence (PL) measurements were carried out. XRD revealed that the powders are free of secondary phases and crystallize in the cubic structure. Raman data show that increasing La doping content increase oxygen vacancies due to lattice expansion. The UV/vis absorption spectroscopy suggested the presence of intermediate energy levels in the band gap of structurally ordered powders. Lanthanum addition creates oxygen vacancies and shifts the photoluminescence in the low energy range leading to intense PL emission.

  3. Lanthanum-modified bentonite: potential for efficient removal of phosphates from fishpond effluents.

    Science.gov (United States)

    Kurzbaum, Eyal; Raizner, Yasmin; Cohen, Oded; Rubinstein, Guy; Bar Shalom, Oded

    2017-06-01

    Adsorption has been suggested as an effective method for removing phosphates from agricultural wastewater effluents that contain relatively high phosphate concentrations. The present study focused on the use of a bentonite-lanthanum clay (Phoslock ® ) for reducing the dissolved phosphate concentration in fishpond effluents. Batch experiments with synthetic phosphate-spiked solutions and with fishpond effluents were performed in order to determine adsorption equilibrium isotherms and kinetics as well as to determine the efficiency of Phoslock ® in removing phosphate from these solutions. In the synthetic phosphate-spiked solution, the mean maximum phosphate adsorption capacity was 92 mg Phoslock ® /mg phosphate removal. A ratio of 50, 100, and 200 mg Phoslock ® /mg phosphate removal was found for complete phosphate removal from the fishpond effluents, where higher doses of Phoslock ® led to a faster removal rate (94% removal within the first 150 min). These results show that bentonite-lanthanum clay can be employed for designing a treatment process for efficient phosphate removal from fishpond effluents.

  4. Chemically produced nanostructured ODS-lanthanum oxide-tungsten composites sintered by spark plasma

    International Nuclear Information System (INIS)

    Yar, Mazher Ahmed; Wahlberg, Sverker; Bergqvist, Hans; Salem, Hanadi G.; Johnsson, Mats; Muhammed, Mamoun

    2011-01-01

    High purity W and W-0.9La 2 O 3 (wt.%) nanopowders were produced by a wet chemical route. The precursor was prepared by the reaction of ammonium paratungstate (APT) with lanthanum salt in aqueous solutions. High resolution electron microscopy investigations revealed that the tungstate particles were coated with oxide precipitates. The precursor powder was reduced to tungsten metal with dispersed lanthanum oxide. Powders were consolidated by spark plasma sintering (SPS) at 1300 and 1400 o C to suppress grain growth during sintering. The final grain size relates to the SPS conditions, i.e. temperature and heating rate, regardless of the starting powder particle size. Scanning electron microscopy revealed that oxide phases were mainly accumulated at grain boundaries while the tungsten matrix constituted of nanosized sub-grains. The transmission electron microscopy revealed that the tungsten grains consist of micron-scale grains and finer sub-grains. EDX analysis confirmed the presence of W in dispersed oxide phases with varying chemical composition, which evidenced the presence of complex oxide phases (W-O-La) in the sintered metals.

  5. Simultaneous determination of dopamine, uric acid and nitrite using carboxylated graphene oxide/lanthanum modified electrode

    International Nuclear Information System (INIS)

    Ye, Fengying; Feng, Chenqi; Jiang, Jibo; Han, Sheng

    2015-01-01

    Highlights: • The carboxylated graphene oxide/lanthanum-modified glassy carbon electrode (GO-COOLa/GCE) was successfully utilized for the simultaneous detection and quantification of DA, UA and NO 2 − . • Combining the benefits of carboxylated graphene oxide and lanthanum, the modified sensor displayed large peak separations, long linear ranges and low detection limits for simultaneously detecting DA, UA and NO 2 − . • The GO-COOLa/GCE electrode showed well stability, good repeatability, rapid response, and high catalytic performance toward the oxidations of DA, UA and NO 2 − . - Abstract: A bare glassy carbon electrode (GCE) was reformed by carboxylated graphene oxide/lanthanum, and the modified electrode, called GO-COOLa/GCE, was fabricated for simultaneously detecting dopamine (DA), uric acid (UA) and nitrite (NO 2 − ) by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and amperometry. Several factors which affected the electrocatalytic activity of the GO-COOLa/GCE electrode, such as the effect of pH, scan rate and concentration were studied. Due to the combination of carboxylated graphene oxide and lanthanum ions, the GO-COOLa/GCE sensor showed rapid response, excellent selectivity and high catalytic performance toward the electrooxidation of DA, UA and NO 2 − . In optimized conditions, two linear response ranges for determining DA were obtained over ranges of 0.01-1.96×10 2 μM and 1.96×10 2 -1.23×10 3 μM with detection limit of 0.018 μM (S/N = 3). And the responses of the GO-COOLa/GCE electrode for UA and NO 2 − were linear in the region of 1-1.53×10 3 μM and 1-2.75×10 3 μM with detection limits of 0.058 μM and 0.070 μM, respectively. Furthermore, this reformed electrode was successfully used to the detection of DA, UA and NO 2 − in real urine and serum samples, showing its promising application in the electroanalysis of real samples.

  6. Electrospray ionization mass spectrometry for the hydrolysis complexes of cisplatin: implications for the hydrolysis process of platinum complexes.

    Science.gov (United States)

    Feifan, Xie; Pieter, Colin; Jan, Van Bocxlaer

    2017-07-01

    Non-enzyme-dependent hydrolysis of the drug cisplatin is important for its mode of action and toxicity. However, up until today, the hydrolysis process of cisplatin is still not completely understood. In the present study, the hydrolysis of cisplatin in an aqueous solution was systematically investigated by using electrospray ionization mass spectrometry coupled to liquid chromatography. A variety of previously unreported hydrolysis complexes corresponding to monomeric, dimeric and trimeric species were detected and identified. The characteristics of the Pt-containing complexes were investigated by using collision-induced dissociation (CID). The hydrolysis complexes demonstrate distinctive and correlative CID characteristics, which provides tools for an informative identification. The most frequently observed dissociation mechanism was sequential loss of NH 3 , H 2 O and HCl. Loss of the Pt atom was observed as the final step during the CID process. The formation mechanisms of the observed complexes were explored and experimentally examined. The strongly bound dimeric species, which existed in solution, are assumed to be formed from the clustering of the parent compound and its monohydrated or dihydrated complexes. The role of the electrospray process in the formation of some of the observed ions was also evaluated, and the electrospray ionization-related cold clusters were identified. The previously reported hydrolysis equilibria were tested and subsequently refined via a hydrolysis study resulting in a renewed mechanistic equilibrium system of cisplatin as proposed from our results. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

  7. Hydrolysis of uranium monocarbide

    International Nuclear Information System (INIS)

    Hajek, B.; Karen, P.; Brozek, V.

    1984-01-01

    The substoichiometric uranium monocarbide UCsub(0.95) was hydrolyzed in acid medium at 80 degC. The composition of the products of hydrolysis corresponds to published data but it correlates better with the stoichiometric composition of the hydrolyzable carbide. The mechanisms of the hydrolytic reaction are discussed and a modified radical mechanism is suggested based on the concept of initiation of the radical process by Hsup(.) radicals formed owing to the nonstoichiometry of the substance. A relation is proposed for calculating the content of free hydrogen in the hydrolysis products of carbides of metallic nature for which a radical mechanism of their reaction with water can be assumed. Some effects occurring during the hydrolysis of uranium carbide, as described in literature, are explained in terms of the concept suggested. The results obtained by the authors for carbides of manganese (Mn 7 C 3 ) and for rare earth elements are discussed. (author)

  8. Hydrolytic gain during hydrolysis reactions : implications and correction procedures

    NARCIS (Netherlands)

    Marchal, L.M.; Tramper, J.

    1999-01-01

    Some of the structural parameters of starch (e.g. % beta- or gluco-hydrolysis) were influenced by the increase in mass during the hydrolysis reactions (hydrolytic gain). Procedures were derived to correct this apparent % of hydrolysis to actual % of hydrolysis. These analytically derived equations

  9. Determination of Aluminum in Dialysis Concentrates by Atomic Absorption Spectrometry after Coprecipitation with Lanthanum Phosphate.

    Science.gov (United States)

    Selvi, Emine Kılıçkaya; Şahin, Uğur; Şahan, Serkan

    2017-01-01

    This method was developed for the determination of trace amounts of aluminum(III) in dialysis concentrates using atomic absorption spectrometry after coprecipitation with lanthanum phosphate. The analytical parameters that influenced the quantitative coprecipitation of analyte including amount of lanthanum, amount of phosfate, pH and duration time were optimized. The % recoveries of the analyte ion were in the range of 95-105 % with limit of detection (3s) of 0.5 µg l -1 . Preconcentration factor was found as 1000 and Relative Standard Deviation (RSD) % value obtained from model solutions was 2.5% for 0.02 mg L -1 . The accuracy of the method was evaluated with standard reference material (CWW-TMD Waste Water). The method was also applied to most concentrated acidic and basic dialysis concentrates with satisfactory results.

  10. Hydrolysis of lactose with -D-galactosidase

    Directory of Open Access Journals (Sweden)

    Vesna Stehlik-Tomas

    2001-06-01

    Full Text Available The conditions of lactose hydrolysis with enzyme preparation of D-galactosidase were investigated. The aim of this work was to considered the use of whey in fermentative processes with yeast Saccharomyces cerevisiae. Enzymatic hydrolysis was conducted at different temperatures, with different lactose concentrations in medium and different concentrations of added enzyme. The results show that optimal temperature for hydrolysis was 40°C. The optimal amount of enzyme preparation was 2 gL-1 in lactose medium with 5-10 % lactose.

  11. PROCESS USING POTASSIUM LANTHANUM SULFATE FOR FORMING A CARRIER PRECIPITATE FOR PLUTONIUM VALUES

    Science.gov (United States)

    Angerman, A.A.

    1958-10-21

    A process is presented for recovering plutonium values in an oxidation state not greater than +4 from fluoride-soluble fission products. The process consists of adding to an aqueous acidic solution of such plutonium values a crystalline potassium lanthanum sulfate precipitate which carries the plutonium values from the solution.

  12. 海藻酸镧颗粒除氟研究:吸附剂物性和吸附机理%Fluoride Removal by Lanthanum Alginate Bead:Adsorbent Characterization and Adsorption Mechanism

    Institute of Scientific and Technical Information of China (English)

    霍亚坤; 丁文明; 黄霞; 徐静年; 赵梦华

    2011-01-01

    Lanthanum alginate bead is a new, highly active adsorbent. In the present study, we investigated its adsorption performance and its adsorption mechanism. The adsorption isotherm for fluoride onto lanthanum alginate bead fits the Langmuir model well, and the maximum adsorption capacity is 197.2 mg·g-1. X-ray diffraction shows the amorphous nature of lanthanum alginate bead, which allows for better accessibility to fluoride and thus better activity. Infrared spectra of lanthanum alginate bead before and after adsorption confirm its stable skeletal structure.Scanning electron microscopy shows that the dense surface structure of the adsorbent appear cracks after adsorption.The adsorption mechanism of lanthanum alginate bead is considered as an ion exchange between F- and Cl- or OH-,as verified from the adsorbent and the solution by pH effect, energy dispersive X-ray, and ion chromatography.

  13. Laser-diode pumped self-mode-locked praseodymium visible lasers with multi-gigahertz repetition rate.

    Science.gov (United States)

    Zhang, Yuxia; Yu, Haohai; Zhang, Huaijin; Di Lieto, Alberto; Tonelli, Mauro; Wang, Jiyang

    2016-06-15

    We demonstrate efficient laser-diode pumped multi-gigahertz (GHz) self-mode-locked praseodymium (Pr3+) visible lasers with broadband spectra from green to deep red for the first time to our knowledge. With a Pr3+-doped GdLiF4 crystal, stable self-mode-locked visible pulsed lasers at the wavelengths of 522 nm, 607 nm, 639 nm, and 720 nm have been obtained with the repetition rates of 2.8 GHz, 3.1 GHz, 3.1 GHz, and 3.0 GHz, respectively. The maximum output power was 612 mW with the slope efficiency of 46.9% at 639 nm. The mode-locking mechanism was theoretically analyzed. The stable second-harmonic mode-locking with doubled repetition frequency was also realized based on the Fabry-Perot effect formed in the laser cavity. In addition, we find that the polarization directions were turned with lasing wavelengths. This work may provide a new way for generating efficient ultrafast pulses with high- and changeable-repetition rates in the visible range.

  14. Kinetic modelling of enzymatic starch hydrolysis

    NARCIS (Netherlands)

    Bednarska, K.A.

    2015-01-01

    Kinetic modelling of enzymatic starch hydrolysis – a summary

    K.A. Bednarska

    The dissertation entitled ‘Kinetic modelling of enzymatic starch hydrolysis’ describes the enzymatic hydrolysis and kinetic modelling of liquefaction and saccharification of wheat starch.

  15. Inductively coupled plasma optical emission spectrometry analysis of lanthanum, samarium and gadolinium oxides for rare earths impurities

    International Nuclear Information System (INIS)

    Reino, L.C.P.; Lordello, A.R.

    1990-09-01

    An inductively coupled plasma optical emission spectrometry method is described for the determination of Sm, Eu, La, Gd, Dy, Pr, Ho, Nd, Tb and Y in purified oxides of lanthanum, samarium and gadolinium. The method enables a simple, precise and readily available determination. Dissolution of the samples is achieved with diluted hydrochloric acid (1:1). The solutions are diluted to volume for a concentration of 1mg/ml. The lowest determination limit is 0,01% for most elements and 0,05 or 0,1% for a few rare earths in samarium and gadolinium matrices. Lanthanum, Samarium and Gadolinium concentrates with purity grade of 99,9%, 99,6% and 99,8%, respectively, can be analysed by this procedure. (author)

  16. Conversion of rice straw to sugars by dilute-acid hydrolysis

    International Nuclear Information System (INIS)

    Karimi, Keikhosro; Kheradmandinia, Shauker; Taherzadeh, Mohammad J.

    2006-01-01

    Hydrolysis of rice straw by dilute sulfuric acid at high temperature and pressure was investigated in one and two stages. The hydrolyses were carried out in a 10-l reactor, where the hydrolysis retention time (3-10 min), pressure (10-35 bar) and acid concentration (0-1%) were examined. Optimization of first stage hydrolysis is desirable to achieve the highest yield of the sugars from hemicellulose and also as a pretreatment for enzymatic hydrolysis. The results show the ability of first stage hydrolysis to depolymerize xylan to xylose with a maximum yield of 80.8% at hydrolysis pressure of 15 bar, 10 min retention time and 0.5% acid concentration. However, the yield of glucose from glucan was relatively low in first stage hydrolysis at a maximum of 25.8%. The solid residuals were subjected to further dilute-acid hydrolysis in this study. This second-stage hydrolysis without addition of the acid could not increase the yield of glucose from glucan beyond 26.6%. On the other hand, the best results of the hydrolysis were achieved, when 0.5% sulfuric acid was added prior to each stage in two-stage hydrolysis. The best results of the second stage of the hydrolysis were achieved at the hydrolysis pressure and the retention time of 30 bar and 3 min in the second stage hydrolysis, where a total of 78.9% of xylan and 46.6% of glucan were converted to xylose and glucose, respectively in the two stages. Formation of furfural and HMF were functions of the hydrolysis pressure, acid concentration, and retention time, whereas the concentration of acetic acid was almost constant at pressure of higher than 10 bar and a total retention time of 10 min

  17. Hydrolysis of alkaline pretreated banana peel

    Science.gov (United States)

    Fatmawati, A.; Gunawan, K. Y.; Hadiwijaya, F. A.

    2017-11-01

    Banana peel is one of food wastes that are rich in carbohydrate. This shows its potential as fermentation substrate including bio-ethanol. This paper presented banana peel alkaline pretreatment and enzymatic hydrolysis. The pretreatment was intended to prepare banana peel in order to increase hydrolysis performance. The alkaline pretreatment used 10, 20, and 30% w/v NaOH solution and was done at 60, 70 and 80°C for 1 hour. The hydrolysis reaction was conducted using two commercial cellulose enzymes. The reaction time was varied for 3, 5, and 7 days. The best condition for pretreatment process was one conducted using 30% NaOH solution and at 80°C. This condition resulted in cellulose content of 90.27% and acid insoluble lignin content of 2.88%. Seven-day hydrolysis time had exhibited the highest reducing sugar concentration, which was7.2869 g/L.

  18. Enzymatic hydrolysis of plant extracts containing inulin

    Energy Technology Data Exchange (ETDEWEB)

    Guiraud, J.P.; Galzy, P.

    1981-10-01

    Inulin-rich extracts of chicory and Jerusalem artichoke are a good potential source of fructose. Total enzymatic hydrolysis of these extracts can be effected by yeast inulinases (EC 3.2.1.7). Chemical prehydrolysis is unfavourable. Enzymatic hydrolysis has advantages over chemical hydrolysis: it does not produce a dark-coloured fraction or secondary substances. It is possible to envisage the preparation of high fructose syrups using this process. (Refs. 42).

  19. Enzymatic hydrolysis of biomimetic bacterial cellulose-hemicellulose composites.

    Science.gov (United States)

    Penttilä, Paavo A; Imai, Tomoya; Hemming, Jarl; Willför, Stefan; Sugiyama, Junji

    2018-06-15

    The production of biofuels and other chemicals from lignocellulosic biomass is limited by the inefficiency of enzymatic hydrolysis. Here a biomimetic composite material consisting of bacterial cellulose and wood-based hemicelluloses was used to study the effects of hemicelluloses on the enzymatic hydrolysis with a commercial cellulase mixture. Bacterial cellulose synthesized in the presence of hemicelluloses, especially xylan, was found to be more susceptible to enzymatic hydrolysis than hemicellulose-free bacterial cellulose. The reason for the easier hydrolysis could be related to the nanoscale structure of the substrate, particularly the packing of cellulose microfibrils into ribbons or bundles. In addition, small-angle X-ray scattering was used to show that the average nanoscale morphology of bacterial cellulose remained unchanged during the enzymatic hydrolysis. The reported easier enzymatic hydrolysis of bacterial cellulose produced in the presence of wood-based xylan offers new insights to overcome biomass recalcitrance through genetic engineering. Copyright © 2018 Elsevier Ltd. All rights reserved.

  20. The oxidation of carbon monoxide over transition metal doped lanthanum manganates nanoparticles

    International Nuclear Information System (INIS)

    Fal Desai, M.S.; Salker, A.V.

    2012-01-01

    Lanthanum manganates perovskites (ABO 3 ) has been widely studied and applied. Many perovskites with A and B sites doped with different metals show good catalytic activity in many oxidation reactions than the individual perovskite. In present study, an attempt has been made to show comparative account of CO oxidation by doping the B site with different cations using sol-gel method

  1. Praseodymium valency from crystal structure in Pr-Ba-Cu-O and (Y-Pr)-Ba-Cu-O single crystals

    International Nuclear Information System (INIS)

    Collin, G.; Albouy, P.A.; Monod, P.; Ribault, M.

    1990-01-01

    The substitution of Pr to Y leads to materials with a general formula (Y 1-v Pr v ) (Ba 2-x Pr x ) (Cu 3-y vac y ) O 6+x/2-y+z and with a structural transition around v + x' ∼ 0.5. For v + x 0.5 the crystals are tetragonal, La 1.5 Ba 1.5 Cu 3 O 7±z type, with the characteristic tri-twinning of this phase. The Pr valency, in the range 3-3.2 + depending on preparation conditions, is determined from interatomic distances. Orthorhombic crystals of Pr Ba Cu O prepared at high temperatures exhibit a high amount of defects, y ∼ 0.25 on the Cu(1) site and are semiconductors with a T -1/4 activation law attributed to the praseodymium valence fluctuation

  2. Kinetics of enzymatic hydrolysis of methyl ricinoleate

    OpenAIRE

    Neeharika, T. S.V.R.; Lokesh, P.; Prasanna Rani, K. N.; Prathap Kumar, T.; Prasad, R. B.N.

    2015-01-01

    Ricinoleic acid is an unsaturated hydroxy fatty acid that naturally occurs in castor oil in proportions of up to 85–90%. Ricinoleic acid is a potential raw material and finds several applications in coatings, lubricant formulations and pharmaceutical areas. Enzymatic hydrolysis of castor oil is preferred over conventional hydrolysis for the preparation of ricinoleic acid to avoid estolide formation. A kinetics analysis of the enzymatic hydrolysis of Methyl Ricinoleate in the presence of Candi...

  3. Bioethanol production: an integrated process of low substrate loading hydrolysis-high sugars liquid fermentation and solid state fermentation of enzymatic hydrolysis residue.

    Science.gov (United States)

    Chu, Qiulu; Li, Xin; Ma, Bin; Xu, Yong; Ouyang, Jia; Zhu, Junjun; Yu, Shiyuan; Yong, Qiang

    2012-11-01

    An integrated process of enzymatic hydrolysis and fermentation was investigated for high ethanol production. The combination of enzymatic hydrolysis at low substrate loading, liquid fermentation of high sugars concentration and solid state fermentation of enzymatic hydrolysis residue was beneficial for conversion of steam explosion pretreated corn stover to ethanol. The results suggested that low substrate loading hydrolysis caused a high enzymatic hydrolysis yield; the liquid fermentation of about 200g/L glucose by Saccharomyces cerevisiae provided a high ethanol concentration which could significantly decrease cost of the subsequent ethanol distillation. A solid state fermentation of enzymatic hydrolysis residue was combined, which was available to enhance ethanol production and cellulose-to-ethanol conversion. The results of solid state fermentation demonstrated that the solid state fermentation process accompanied by simultaneous saccharification and fermentation. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. Thermal stability and microstructure of catalytic alumina composite support with lanthanum species

    Science.gov (United States)

    Ozawa, Masakuni; Nishio, Yoshitoyo

    2016-09-01

    Lanthanum (La) modified γ-alumina composite was examined for application toward thermostable catalytic support at elevated temperature. La added alumina was prepared through an aqueous process using lanthanum (III) nitrate and then characterized by surface area measurement, X-ray powder diffraction (XRD), differential thermal analysis (DTA), scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray photoemission spectroscopy (XPS) and surface desorption of CO2. It was found that the properties depended on the La content and heat treatment temperatures. The characterization of the surface, structural and chemical properties of La-Al2O3 showed the existence of a strong interaction between the La species and alumina via formation of new phase and modified surface in Al2O3 samples. LaAlO3 nanoparticle formed among alumina particles by the solid phase reaction of Al2O3 and La2O3. The increase of the surface basicity of La modified alumina was demonstrated using CO2 temperature programmed desorption experiments. The controlled surface interaction between La oxide and alumina provide the unique surface and structural properties of the resulting mixed oxides as catalysts and catalytic supports.

  5. Molecular distribution and toxicity assessment of praseodymium by Spirodela polyrrhiza

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Ting; Su, Chunlei; Hu, Dan; Li, Feifei; Lu, Qianqian; Zhang, Tingting; Xu, Qinsong, E-mail: xuqinsong@njnu.edu.cn

    2016-07-15

    Highlights: • Pr was mainly bound to cellulose and pectin in Spirodela polyrrhiza. • Pr induced the change in C−O, C−H, and O−H stretching vibration by FTIR. • Pr induced per oxidation of unsaturated fatty acids in membrane lipids. • Pr could target the reaction center proteins D1 and D2. • The reduction in photo system II activity was detected under Pr exposure. - Abstract: Aquatic macrophytes are known to accumulate and bioconcentrate metals. In this study, the physiological, biochemical, and ultrastructural responses of Spirodela polyrrhiza to elevated concentrations of praseodymium (Pr), ranging from 0 to 60 μM, were investigated over 20 d exposure. The results showed that the accumulation of Pr in S. polyrrhiza occurred in a concentration-dependent manner. The accumulation of Pr in biomacromolecules decreased in the order of cellulose and pectin (65–69%), crude proteins (18–25%), crude polysaccharides (6–10%), crude lipids (3%–4%). Significant increases in malondialdehyde (MDA), and decreases in photosynthetic pigment, soluble protein, and unsaturated fatty acids showed that Pr induced oxidative stress. Inhibitory effects on photosystem II and the degradation of the reaction center proteins D1 and D2 were revealed by chlorophyll a fluorescence transients, immunoblotting, and damage to chloroplast ultrastructure. Significant increases in cell death were observed in Pr-treated plants. However, S. polyrrhiza can combat Pr induced oxidative injury by activating various enzymatic and non-enzymatic antioxidants. These results will improve understanding of the biological consequences of rare earth elements (REEs) contamination, particularly in aquatic bodies.

  6. Effect of praseodymium dopants on the optical, crystallinity and electrochemical properties of poly(vinylalcohol) films fayez

    International Nuclear Information System (INIS)

    Ali, M.; Amwar, Z.M.

    2005-01-01

    Pure Poly(vinylalcohol) (Pva) films and doped with Praseodymium (Pr) in the concentration range of 5-30% weight/weight (w/w) were prepared by a casting technique. Optical transmission measurements were performed on the prepared samples, where an interesting feature is the enhancement of the transmission over 100% due to the incorporation of the Pr in the Pva films. The refractive indices of the studied doped films were general lower than that of the pure Pva. On adding Pr to the Pva the films become more crystalline due to the coordination of the lanthanide metal ion (Pr) to the Oxygen of the Pva side chain. The doped Pva samples exhibit different electrochemical behaviour through the cyclic voltammetry (C V) and square wave voltammetry (Sv) than the pure Pva sample. It was found that the corrosion behavior of the doped Pva films in the seawater is less than the pure Pva in the same environment

  7. Rare earth elements: end use and recyclability

    Science.gov (United States)

    Goonan, Thomas G.

    2011-01-01

    Rare earth elements are used in mature markets (such as catalysts, glassmaking, lighting, and metallurgy), which account for 59 percent of the total worldwide consumption of rare earth elements, and in newer, high-growth markets (such as battery alloys, ceramics, and permanent magnets), which account for 41 percent of the total worldwide consumption of rare earth elements. In mature market segments, lanthanum and cerium constitute about 80 percent of rare earth elements used, and in new market segments, dysprosium, neodymium, and praseodymium account for about 85 percent of rare earth elements used. Regardless of the end use, rare earth elements are not recycled in large quantities, but could be if recycling became mandated or very high prices of rare earth elements made recycling feasible.

  8. Cost-Effectiveness of First-Line Sevelamer and Lanthanum versus Calcium-Based Binders for Hyperphosphatemia of Chronic Kidney Disease.

    Science.gov (United States)

    Habbous, Steven; Przech, Sebastian; Martin, Janet; Garg, Amit X; Sarma, Sisira

    2018-03-01

    Phosphate binders are used to treat hyperphosphatemia among patients with chronic kidney disease (CKD). To conduct an economic evaluation comparing calcium-free binders sevelamer and lanthanum with calcium-based binders for patients with CKD. Effectiveness data were obtained from a recent meta-analysis of randomized trials. Effectiveness was measured as life-years gained and translated to quality-adjusted life-years (QALYs) using utility weights from the literature. A Markov model consisting of non-dialysis-dependent (NDD)-CKD, dialysis-dependent (DD)-CKD, and death was developed to estimate the incremental costs and effects of sevelamer and lanthanum versus those of calcium-based binders. A lifetime horizon was used and both costs and effects were discounted at 1.5%. All costs are presented in 2015 Canadian dollars from the Canadian public payer perspective. Results of probabilistic sensitivity analysis were presented using cost-effectiveness acceptability curves. Sensitivity analyses were conducted for risk pooling methods, omission of dialysis costs, and persistence of drug effects on mortality. Sevelamer resulted in an incremental cost-effectiveness ratio of $106,522/QALY for NDD-CKD and $133,847/QALY for DD-CKD cohorts. Excluding dialysis costs, sevelamer was cost-effective in the NDD-CKD cohort ($5,847/QALY) and the DD-CKD cohort ($11,178/QALY). Lanthanum was dominated regardless of whether dialysis costs were included. Existing evidence does not clearly support the cost-effectiveness of non-calcium-containing phosphate binders (sevelamer and lanthanum) relative to calcium-containing phosphate binders in DD-CKD patients. Our study suggests that sevelamer may be cost-effective before dialysis onset. Because of the remaining uncertainty in several clinically relevant outcomes over time in DD-CKD and NDD-CKD patients, further research is encouraged. Copyright © 2018 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier

  9. Synthesis and Stability of Lanthanum Superhydrides

    Energy Technology Data Exchange (ETDEWEB)

    Geballe, Zachary M. [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Liu, Hanyu [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Mishra, Ajay K. [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Permanent address: HP& SRPD, Bhabha Atomic Research Center, Mumbai-85 India; Ahart, Muhtar [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Somayazulu, Maddury [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Meng, Yue [HPCAT, Geophysical Laboratory, Carnegie Institution of Washington, Argonne IL 60439 USA; Baldini, Maria [Geophysical Laboratory, Carnegie Institution of Washington, Washington DC 20015 USA; Hemley, Russell J. [Institute of Materials Science and Department of Civil and Environmental Engineering, The George Washington University, Washington DC 20052 USA

    2017-12-15

    Recent theoretical calculations predict that megabar pressure stabilizes very hydrogen-rich simple compounds having new clathrate-like structures and remarkable electronic properties including room-temperature superconductivity. X-ray diffraction and optical studies demonstrate that superhydrides of lanthanum can be synthesized with La atoms in an fcc lattice at 170 GPa upon heating to about 1000 K. The results match the predicted cubic metallic phase of LaH10 having cages of thirty-two hydrogen atoms surrounding each La atom. Upon decompression, the fcc-based structure undergoes a rhombohedral distortion of the La sublattice. The superhydride phases consist of an atomic hydrogen sublattice with H-H distances of about 1.1 Å, which are close to predictions for solid atomic metallic hydrogen at these pressures. With stability below 200 GPa, the superhydride is thus the closest analogue to solid atomic metallic hydrogen yet to be synthesized and characterized.

  10. Cerium-activated lanthanum beryllate as a gamma detector material

    International Nuclear Information System (INIS)

    Czirr, J.B.; Berrondo, M.

    1994-01-01

    The authors have tested a single crystal of Ce-activated lanthanum beryllate BEL(Ce) as a potential gamma detector material. The density (6.1 g.cm -3 ) and decay time (50 ns) are competitive with other recently developed materials. The scintillation efficiency is 57 to 95% that of BGO. For an excitation wavelength of 340 nm, the emission spectra is a broad peak centered at 450 mn. The H 2 annealed sample is transparent for wavelengths greater than 400 mn. They are continuing a program to improve the scintillation efficiency by varying the crystal growth conditions

  11. Synthesis of calcium doped lanthanum manganite by mechanosynthesis

    International Nuclear Information System (INIS)

    Bolarin, A.M.; Sanchez, F.; Palomares, S.; Aguilar, J.A.; Torres-Villasenor, G.

    2007-01-01

    Lanthanum manganite doped with calcium, Ca 1/3 La 2/3 MnO 3-δ , was prepared by a high-energy ball milling. The precursors used were Mn 2 O 3 , La 2 O 3 and CaO, mixed in the stoichiometric ratio to obtain this manganite. The mechano-chemical process was performed at room temperature in a SPEX 8000D mixer/mill, using hardened steel balls and stainless steel vials, in air atmosphere. X-ray diffraction was used to elucidate the phase transformation as a function of the milling time. The Rietveld refinement was used in order to characterize structurally the manganites. The morphology and particle size of powder compound obtained were characterized by scanning electron microscope. The particle size of this powder material was measured with zeta size analyzer, and selected area electron diffraction (SAED) from TEM was used to elucidate the crystalline structure of this powder compound. The results showed that it is possible to obtain calcium doped lanthanum manganite by mechano-synthesis, using a weight ratio of ball to powder of 12:1, after 3 h of milling. The evolution of the phase transformation during the milling time is reported. Increases in milling time produce exponential decrease in the particle size, up to 680 nm after 1 h of milling. After the milling process it is obtained a powder compound with an orthorhombic structure (S.G. Pbnm). A prolonged milling time (>9 h) produce an important reduction in the particle size but this is accompanied with a high iron contamination caused by metallic residues originated from vial and balls and also, after 9 h of milling time, it was found an important distortion in orthorhombic structure, obtaining two types of parameters

  12. Solid state interaction studies on binary nitrate mixtures of uranyl nitrate hexahydrate and lanthanum nitrate hexahydrate at elevated temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Kalekar, Bhupesh; Raje, Naina, E-mail: nraje@barc.gov.in; Reddy, A.V.R.

    2017-02-15

    Interaction behavior of uranyl nitrate hexahydrate (UNH) and lanthanum nitrate hexahydrate (LaNH) have been investigated on the mixtures in different molar ratios of the two precursors and monitoring the reactions at elevated temperatures with thermoanalytical and X-ray diffraction measurement techniques. During the decomposition of equimolar mixture of LaNH and UNH, formation of lanthanum uranate (U{sub 0.5}La{sub 0.5})O{sub 2}, was seen by the temperature of 500 °C along with lanthanum oxide (La{sub 2}O{sub 3}) and uranium trioxide (UO{sub 3}). By the temperature of 700 °C, the formation of uranium sesquioxide (U{sub 3}O{sub 8}) was observed along with (U{sub 0.5}La{sub 0.5})O{sub 2} as end products in uranium rich mixtures. Lanthanum rich compositions decomposed by the temperature of 700 °C to give (U{sub 0.5}La{sub 0.5})O{sub 2} and La{sub 2}O{sub 3} as end products. - Highlights: • UO{sub 2}(NO{sub 3}){sub 2}.6H{sub 2}O and La(NO{sub 3}){sub 3}.6H{sub 2}O interact through their intermediates. • Formation of (U{sub 0.5}La{sub 0.5})O{sub 2} by 500 °C. • La deficient mixtures decompose to give U{sub 3}O{sub 8} and (U{sub 0.5}La{sub 0.5})O{sub 2} as end products. • La rich mixtures decompose to give La{sub 2}O{sub 3} and (U{sub 0.5}La{sub 0.5})O{sub 2} as end product.

  13. Hydrolysis reactor for hydrogen production

    Science.gov (United States)

    Davis, Thomas A.; Matthews, Michael A.

    2012-12-04

    In accordance with certain embodiments of the present disclosure, a method for hydrolysis of a chemical hydride is provided. The method includes adding a chemical hydride to a reaction chamber and exposing the chemical hydride in the reaction chamber to a temperature of at least about 100.degree. C. in the presence of water and in the absence of an acid or a heterogeneous catalyst, wherein the chemical hydride undergoes hydrolysis to form hydrogen gas and a byproduct material.

  14. Paramagnetic centers in two phases of manganese-doped lanthanum gallate

    Science.gov (United States)

    Vazhenin, V. A.; Potapov, A. P.; Guseva, V. B.; Artyomov, M. Yu.

    2009-05-01

    An EPR study of two phases of manganese-doped lanthanum gallate (with a first-order structural transition occurring at 430 K) has revealed Gd3+, Fe3+, and Mn4+ centers at room temperature and 438 K. The parameters of spin Hamiltonians are determined for the Gd3+, Fe3+, and Mn4+ rhombohedral centers in the high-temperature phase (with no other centers found here) and for the monoclinic center Gd3+ in the low-temperature phase. Both in the orthorhombic and in the rhombohedral phase, crystallographic twins (or ferroelastic domains) are observed.

  15. Lanthanum gallate substrates for epitaxial high-temperature superconducting thin films

    Science.gov (United States)

    Sandstrom, R. L.; Giess, E. A.; Gallagher, W. J.; Segmuller, A.; Cooper, E. I.

    1988-11-01

    It is demonstrated that lanthanum gallate (LaGaO3) has considerable potential as an electronic substrate material for high-temperature superconducting films. It provides a good lattice and thermal expansion match to YBa2Cu3O(7-x), can be grown in large crystal sizes, is compatible with high-temperature film processing, and has a reasonably low dielectric constant and low dielectric losses. Epitaxial YBa2Cu3O(7-x) films grown on LaGaO3 single-crystal substrates by three techniques have zero resistance between 87 and 91 K.

  16. Hydrolysis of corn oil using subcritical water

    Directory of Open Access Journals (Sweden)

    Pinto Jair Sebastião S.

    2006-01-01

    Full Text Available This work presents the results of a study on the use of subcritical water as both solvent and reactant for the hydrolysis of corn oil without the use of acids or alkalis at temperatures of 150-280 degreesC. Corn oil hydrolysis leads to the formation of its respective fatty acids with the same efficiency of conventional methods. Fatty acids form an important group of products, which are used in a range of applications. The confirmation and identification of the hydrolysis products was done by HT-HRGC-FID and HRGC/MS.

  17. Bordoni relaxation and magnetic transformation in cerium and cerium-lanthanum alloys

    Energy Technology Data Exchange (ETDEWEB)

    Postnikov, V S; Polner, G L; Sharshakov, I M

    1975-11-01

    The internal friction in pure cerium and cerium-base alloys with 2.5 and 12 weight percent of lanthanum added at temperature ranging from 4.2 deg up to 77/sup 0/K is described. Amplitude-independent internal friction has been measured with an inverse torsion pendulum with a specimen oscillation frequency of 1-30 hz in vacuum not less than 1.10/sup -5/ torr. A temperature of the specimen has been determined with a capacitance-type sensor and a gas gage. A curve showing the dependence of internal friction upon a temperature of pure cerium has two distinct peaks; the first at 12.5/sup 0/K, the second at 45/sup 0/K. The 12.5/sup 0/K peak is accounted for by a transition of antiferromagnetic ..beta..-Ce into a paramagnetic state. The 45/sup 0/K peak is a Bordoni maximum. The paper describes an influence of additions, specimen oscillation frequency variations, deformation and annealing upon the peak behavor. Added lanthanum reduces not only a peak temperature but a height as well. Studies of the 45/sup 0/K peak have shown that its temperature location depends upon the specimen oscillation frequency. As the frequency increases the peak tends to a range of high temperatures which confirms its relaxation nature.

  18. Electronic-structure calculations of praseodymium metal by means of modified density-functional theory

    International Nuclear Information System (INIS)

    Svane, A.; Trygg, J.; Johansson, B.; Eriksson, O.

    1997-01-01

    Electronic-structure calculations of elemental praseodymium are presented. Several approximations are used to describe the Pr f electrons. It is found that the low-pressure, trivalent phase is well described using either the self-interaction corrected (SIC) local-spin-density (LSD) approximation or the generalized-gradient approximation (GGA) with spin and orbital polarization (OP). In the SIC-LSD approach the Pr f electrons are treated explicitly as localized with a localization energy given by the self-interaction of the f orbital. In the GGA+OP scheme the f-electron localization is described by the onset of spin and orbital polarization, the energetics of which is described by spin-moment formation energy and a term proportional to the total orbital moment, L z 2 . The high-pressure phase is well described with the f electrons treated as band electrons, in either the LSD or the GGA approximations, of which the latter describes more accurately the experimental equation of state. The calculated pressure of the transition from localized to delocalized behavior is 280 kbar in the SIC-LSD approximation and 156 kbar in the GGA+OP approach, both comparing favorably with the experimentally observed transition pressure of 210 kbar. copyright 1997 The American Physical Society

  19. Phases in lanthanum-nickel-aluminum alloys

    International Nuclear Information System (INIS)

    Mosley, W.C.

    1992-01-01

    Lanthanum-nickel-aluminum (LANA) alloys will be used to pump, store and separate hydrogen isotopes in the Replacement Tritium Facility (RTF). The aluminum content (y) of the primary LaNi 5 -phase is controlled to produce the desired pressure-temperature behavior for adsorption and desorption of hydrogen. However, secondary phases cause decreased capacity and some may cause undesirable retention of tritium. Twenty-three alloys purchased from Ergenics, Inc. for development of RTF processes have been characterized by scanning electron microscopy (SEM) and by electron microprobe analysis (EMPA) to determine the distributions and compositions of constituent phases. This memorandum reports the results of these characterization studies. Knowledge of the structural characteristics of these alloys is a useful first step in selecting materials for specific process development tests and in interpreting results of those tests. Once this information is coupled with data on hydrogen plateau pressures, retention and capacity, secondary phase limits for RTF alloys can be specified

  20. Synthesis and stability of lanthanum superhydrides

    Energy Technology Data Exchange (ETDEWEB)

    Geballe, Zachary M.; Liu, Hanyu; Mishra, Ajay K.; Ahart, Muhtar; Somayazulu, Maddury; Baldini, Maria [Geophysical Laboratory, Carnegie Institution, Washington, DC (United States); Meng, Yue [HPCAT, Geophysical Laboratory, Carnegie Institution of Washington, Argonne, IL (United States); Hemley, Russell J. [Institute of Materials Science and Department of Civil and Environmental Engineering, The George Washington University, Washington, DC (United States)

    2018-01-15

    Recent theoretical calculations predict that megabar pressure stabilizes very hydrogen-rich simple compounds having new clathrate-like structures and remarkable electronic properties including room-temperature superconductivity. X-ray diffraction and optical studies demonstrate that superhydrides of lanthanum can be synthesized with La atoms in an fcc lattice at 170 GPa upon heating to about 1000 K. The results match the predicted cubic metallic phase of LaH{sub 10} having cages of thirty-two hydrogen atoms surrounding each La atom. Upon decompression, the fcc-based structure undergoes a rhombohedral distortion of the La sublattice. The superhydride phases consist of an atomic hydrogen sublattice with H-H distances of about 1.1 Aa, which are close to predictions for solid atomic metallic hydrogen at these pressures. With stability below 200 GPa, the superhydride is thus the closest analogue to solid atomic metallic hydrogen yet to be synthesized and characterized. (copyright 2018 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  1. Preferable adsorption of phosphate using lanthanum-incorporated porous zeolite: Characteristics and mechanism

    Science.gov (United States)

    He, Yinhai; Lin, Hai; Dong, Yingbo; Wang, Liang

    2017-12-01

    The adsorbent, where lanthanum oxide was incorporated onto porous zeolite (La-Z), of preferable adsorption towards phosphate was prepared by hydrothermal synthesis. Based on pH effect results, La-Z would effectively sequestrate phosphate over wider pH range of 3.0-7.0, alkaline conditions were unfavorable for phosphate. The adsorption of phosphate was not significantly influenced by ionic strength and by coexisting anions of chloride, nitrate and sulfate but bicarbonate showed slightly greater negative effects, indicating La-Z possessed highly selectivity to phosphate. Adsorption of phosphate could be well fitted by pseudo-second-order model and the process was mainly controlled by intra-particle diffusion. Equilibrium adsorption demonstrated that Langmuir model was more suitable than Freundlich model for description phosphate adsorption and the adsorption capacity was 17.2 mg P g-1, which exhibited 95% utilization of incorporated La. Over 95% phosphate was eliminated in real effluent treatment when the dose was 2 g L-1. The underlying mechanism for phosphate capture was probed with Zeta potential and X-ray photoelectron spectroscope analysis, and the formation of La-P inner-sphere complexation was testified to be the dominant pathway. All the results suggested that the porous zeolite-supported lanthanum oxide can serve as a promising adsorbent for phosphate removal in realistic application.

  2. Kinetics of catalyzed hydrolysis of 4-methylumbelliferyl caprylate (MUCAP) salmonella reagent

    Science.gov (United States)

    Al-Kady, Ahmed S.; Ahmed, El-Sadat I.; Gaber, M.; Hussein, Mohamed M.; Ebeid, El-Zeiny M.

    2011-09-01

    The kinetics of chemical hydrolysis including neutral, acid- and base-catalyzed hydrolysis of 4-methylumbelliferyl caprylate (MUCAP) salmonella reagent were studied at different temperatures. The rate constants and activation parameters were determined by following the build-up of fluorescence peak of the hydrolysis product 4-methylumbelliferone (4-MU). The time scale of esterase enzyme hydrolysis caused by salmonella was compared with chemical hydrolysis as a background process.

  3. Short-time ultrasonication treatment in enzymatic hydrolysis of biomass

    Science.gov (United States)

    Zengqian Shi; Zhiyong Cai; Siqun Wang; Qixin Zhong; Joseph J. Bozell

    2013-01-01

    To improve the conversion of enzymatic hydrolysis of biomass in an energy-efficient manner, two shorttime ultrasonication strategies were applied on six types of biomass with different structures and components. The strategies include pre-sonication before the hydrolysis and intermittent sonication during the ongoing hydrolysis. The microstructures of each type of...

  4. [Prediction of common buffer catalysis in hydrolysis of fenchlorazole-ethyl].

    Science.gov (United States)

    Lin, Jing; Chen, Jing-wen; Zhang, Si-yu; Cai, Xi-yun; Qiao, Xian-liang

    2008-09-01

    The purpose of this study was to elucidate the effects of temperatures, pH levels and buffer catalysis on the hydrolysis of FCE. The hydrolysis of FCE follows first-order kinetics at different pH levels and temperatures. FCE hydrolysis rates are greatly increased at elevated pH levels and temperatures. The maximum contribution of buffer catalysis to the hydrolysis of FCE was assessed based on application of the Bronsted equations for general acid-base catalysis. The results suggest that the buffer solutions play an obvious catalysis role in hydrolysis of FCE and the hydrolysis rates of FCE are quickened by the buffer solutions. Besides, the buffer catalysis capacity of different buffer solutions is diverse, and the buffer catalysis capacity at different pH levels with the same buffer solutions is different, too. The phosphate buffer at pH = 7 shows the maximal buffer catalysis capacity. The hydrolysis rate constants of FCE as a function of temperature and pH, which were remedied by the buffer catalysis factor, were mathematically combined to predict the hydrolytic dissipation of FCE. The equation suggests that the hydrolysis half-lives of FCE ranged from 7 d to 790 d. Hydrolysis metabolites of FCE were identified by liquid chromatography-mass spectrometry. In basic conditions (pH 8-10), fenchlorazole was formed via breakdown of the ester bond of the safener.

  5. Atom states and interatomic interactions in complex perovskite-like oxides. Communication XX. Origin of electron-ionic conductivity in lanthanum gallates doped with strontium and chromium

    International Nuclear Information System (INIS)

    Chezhina, N.V.; Zolotukhina, N.V.; Pijr, I.V.

    2006-01-01

    Magnetic susceptibilities and electric conductivities of solid solutions based on lanthanum gallate containing chromium and strontium atoms in the ratio of 10 : 2 were studied. It was shown that no partial oxidation of chromium to Cr(IV) occurs when lanthanum gallate is doped with chromium and strontium simultaneously, whereas the ionic conductivity is associated with the appearance of vacancies stabilized by chromium atoms in the oxygen sublattice [ru

  6. Internal-standard method for the determination of uranium, thorium, lanthanum and europium in carbonaceous shale and monazite by epithermal neutron activation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Shuenn-Gang; Tsai, Hui-Tuh; Wu, Shaw-Chii [Institute of Nuclear Energy Research, Lung-Tan (Taiwan, Republic of China)

    1981-10-03

    An internal-standard method was applied for the determination of uranium, thorium, lanthanum and europium is carbonaceous shale samples and monazite sand by epithermal neutron activation analysis using gold as an internal standard element. The samples were irradiated in a zero-power reactor at the Institute of Nuclear Energy Research and measured with a high-resolution Ge(Li) detector. The detection limit is 0.1 ppm for uranium and europium, 1 ppm for thorium, 5 ppm for lanthanum, and the realative error of all elements is within +-2.6%.

  7. Relaxation effects in oxygen-conducting oxides on base of lanthanum gallate (La, Sr)(Ga, Me)O3, Me = Mg, Fe

    International Nuclear Information System (INIS)

    Glavatskikh, T.Yu.; Venskovskij, N.U.; Kaleva, G.M.; Mosunov, A.V.; Politova, E.D.; Stefanovich, S.Yu.

    2003-01-01

    The dielectric and electric conducting properties of the heterosubstituted perovskite-like solid solutions (La, Sr)(Ga, Me)O 3 , Me Mg, Fe are studied. The increase in the ceramics electric conductivity, conditioned by increase in the ion constituent at strengthening the nonstoichiometry by oxygen and electron constituent by the additional introduction of iron is observed by replacing the part of the lanthanum and gallium cations by strontium, magnesium and iron in the solid solutions on the basis of the lanthanum gallate. The ceramics relaxation behavior is identified; the applicability of the model of the vacational electron transfer for the dipole relaxation is established [ru

  8. Ionic conductivity and fuel cell properties of apatite-type lanthanum silicates doped with Mg and containing excess oxide ions

    Energy Technology Data Exchange (ETDEWEB)

    Yoshioka, Hideki [Hyogo Prefectural Institute of Technology, 3-1-12 Yukihira-cho, Suma-ku, Kobe 654-0037 (Japan); Nojiri, Yoshihiro [Kyushu University, Department of Mechanical Engineering Science, Faculty of Engineering, Motooka 744, Nishi-ku, Fukuoka 819-0935 (Japan); Tanase, Shigeo [National Institute of Advanced Industrial Science and Technology, 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577 (Japan)

    2008-11-30

    Enhancement of the ionic conductivity of lanthanum silicate-based apatites is examined with emphasis on optimizing the La composition and the Mg doping level at the same time. La{sub 10}Si{sub 5.8}Mg{sub 0.2}O{sub 26.8} and La{sub 9.8}Si{sub 5.7}Mg{sub 0.3}O{sub 26.4} show the highest level of the ionic conductivities among apatite silicates, 8.8 and 7.4 x 10{sup -} {sup 2} S cm{sup -} {sup 1} at 800 C, respectively, with a very low level of activation energy (0.42-0.43 eV). Their conductivities are higher than yttria stabilized zirconia (YSZ) below 900 C and even comparable to Sr and Mg doped lanthanum gallate (LSGM) below 550 C. A solid oxide fuel cell using La{sub 9.8}Si{sub 5.7}Mg{sub 0.3}O{sub 26.4} as an electrolyte with Ni-ceria cermet anode and Sr doped lanthanum cobaltite cathode exhibits a remarkable improvement in power generation compared to previous data using Pt electrodes. Structural investigation by the Rietveld analysis on the powder X-ray diffraction pattern shows significant enlargement of the bottleneck triangle sizes of the conduction channel with the Mg doping. (author)

  9. Sinterability and conductivity of barium doped aluminium lanthanum oxyapatite La{sub 9.5}Ba{sub 0.5}Si{sub 5.5}Al{sub 0.5}O{sub 26.5} electrolyte of solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Cao Xiaoguo [Faculty of Materials and Energy, Guangdong University of Technology, Guangzhou 510006, Guangdong (China); Jiang Sanping, E-mail: s.jiang@curtin.edu.au [Fuels and Energy Technology Institute and Department of Chemical Engineering, Curtin University, Perth, WA 6102 (Australia)

    2012-05-15

    Highlights: Black-Right-Pointing-Pointer Ba doping enhances the sintering and densification properties of aluminium lanthanum apatite. Black-Right-Pointing-Pointer Ba doping improves the oxide conductivity of aluminium lanthanum apatite. Black-Right-Pointing-Pointer The enhancement of Ba doping is mainly due to the significantly reduced grain boundary resistance of the aluminium lanthanum apatite. - Abstract: Apatite ceramics are interesting alternative solid oxide fuel cells (SOFCs) electrolytes because of their open structure for the transportation of oxide ions and their good chemical stability. This study reports the influence of barium doping on the microstructure, sinterability and oxide conductivity properties of the aluminium lanthanum oxyapatite La{sub 9.5}Ba{sub 0.5}Si{sub 5.5}Al{sub 0.5}O{sub 26.5}. SEM results show that lanthanum substitution with barium improves the sinterability of apatite ceramics. The barium doping also enhances the conductivity of the aluminium lanthanum silicates. The oxygen ion conductivity of La{sub 9.5}Ba{sub 0.5}Si{sub 5.5}Al{sub 0.5}O{sub 26.5} sintered at 1600 Degree-Sign C is 2.21 Multiplication-Sign 10{sup -2} S cm{sup -1} at 800 Degree-Sign C, higher than 9.81 Multiplication-Sign 10{sup -3} S cm{sup -1} of La{sub 10}Si{sub 5}AlO{sub 26.5} sample prepared under the same conditions. The results in the present study demonstrate that doping Ba on the La site for aluminium lanthanum oxyapatite reduces the sintering temperature and improves the ion conductivity. The enhancement of Ba dopant is mainly on the improvement of the densification and thus substantially reduced grain boundary resistance of aluminium lanthanum oxyapatite particularly at low temperatures.

  10. Hydrolysis of lactose: a literature review

    Energy Technology Data Exchange (ETDEWEB)

    Gekas, V; Lopez-Leiva, M

    1985-02-01

    Lactose is the sugar found in milk and whey. Its hydrolysis to glucose and galactose in milk would solve the problem of milk-intolerant people and in whey it would avoid environmental pollution and offer an interesting possibility of by-product utilization. The prepared sweet syrup has many potential applications in the food industry. Hydrolysis of lactose can be carried out by heating at low pH (acid hydrolysis) or by enzymatic catalysis with the enzyme (lactase or ..beta..-D-galactosidase) either free in solution or immobilized by one of the several enzyme immobilization methods which are abundant in the literature. Selection of the proper method depends on many factors: the nature of substrate, use of the final product, need for sanitary conditions, and, of course, capital and processing costs. 157 references.

  11. In situ XANES cell used for the study of lanthanum strontium cuprate deNOx catalysts

    DEFF Research Database (Denmark)

    Hagen, Anke

    2011-01-01

    , maintaining charge neutrality, with the concentration of oxygen vacancies likely increasing at substitution ratios larger than Sr/La>0.08. During heating in air, the valence of copper ions in the structure increased. Upon exposure to NO at 500 °C the valence of copper ions in a lanthanum strontium cuprate...

  12. Lanthanum gallate substrates for epitaxial high-temperature superconducting thin films

    International Nuclear Information System (INIS)

    Sandstrom, R.L.; Giess, E.A.; Gallagher, W.J.; Segmueller, A.; Cooper, E.I.; Chisholm, M.F.; Gupta, A.; Shinde, S.; Laibowitz, R.B.

    1988-01-01

    We demonstrate that lanthanum gallate (LaGaO 3 ) has considerable potential as an electronic substrate material for high-temperature superconducting films. It provides a good lattice and thermal expansion match to YBa 2 Cu 3 O/sub 7-//sub x/, can be grown in large crystal sizes, is compatible with high-temperature film processing, and has a reasonably low dielectric constant (ε≅25) and low dielectric losses. Epitaxial YBa 2 Cu 3 O/sub 7-//sub x/ films grown on LaGaO 3 single-crystal substrates by three techniques have zero resistance between 87 and 91 K

  13. Catalytic activity of lanthanum oxide for the reduction of cyclohexanone

    International Nuclear Information System (INIS)

    Sugunan, S.; Sherly, K.B.

    1994-01-01

    Lanthanum oxides, La 2 O 3 has been found to be an effective catalyst for the liquid phase reduction of cyclohexanone. The catalytic activities of La 2 O 3 activated at 300, 500 and 800 degC and its mixed oxides with alumina for the reduction of cylcohexanone with 2-propanol have been determined and the data parallel that of the electron donating properties of the catalysts. The electron donating properties of the catalysts have been determined from the adsorption of electron acceptors of different electron affinities on the surface of these oxides. (author). 15 refs., 2 figs., 1 tab

  14. Effects of polyaluminum chloride and lanthanum-modified bentonite on the growth rates of three Cylindrospermopsis raciborskii strains

    NARCIS (Netherlands)

    Araújo, Fabiana; van Oosterhout, Frank; Becker, Vanessa; Attayde, José Luiz; Lürling, Miquel

    2018-01-01

    In tropical and subtropical lakes, eutrophication often leads to nuisance blooms of Cylindrospermopsis raciborskii. In laboratory experiments, we tested the combined effects of flocculant polyaluminum chloride (PAC) and lanthanum-modified bentonite (LMB) on the sinking and growth rates of three C.

  15. effect of post-precipitation treatment on the pore-structure stability of sol-gel derived lanthanum zirconate

    NARCIS (Netherlands)

    Nair, Jalajakumari; Kumar, K.N.P.; Nair, P.; van Ommen, J.G.; Ross, J.R.H.; Ross, Julian R.H.; Burggraaf, Anthonie J.; Burggraaf, Anthonie

    1998-01-01

    The importance of post-precipitation treatments (pore-fluid exchange and its removal) on the evolution of the texture of coprecipitated lanthanum zirconate has been investigated. The nature of the pore fluid and the type of fluid-removal (drying) process have shown a profound effect on the aggregate

  16. A process for producing lignin and volatile compounds from hydrolysis liquor.

    Science.gov (United States)

    Khazraie, Tooran; Zhang, Yiqian; Tarasov, Dmitry; Gao, Weijue; Price, Jacquelyn; DeMartini, Nikolai; Hupa, Leena; Fatehi, Pedram

    2017-01-01

    Hot water hydrolysis process is commercially applied for treating wood chips prior to pulping or wood pellet production, while it produces hydrolysis liquor as a by-product. Since the hydrolysis liquor is dilute, the production of value-added materials from it would be challenging. In this study, acidification was proposed as a viable method to extract (1) furfural and acetic acid from hot water hydrolysis liquor and (2) lignin compounds from the liquor. The thermal properties of the precipitates made from the acidification of hydrolysis liquor confirmed the volatile characteristics of precipitates. Membrane dialysis was effective in removing inorganic salts associated with lignin compounds. The purified lignin compounds had a glass transition temperature (Tg) of 180-190 °C, and were thermally stable. The results confirmed that lignin compounds present in hot water hydrolysis liquor had different characteristics. The acidification of hydrolysis liquor primarily removed the volatile compounds from hydrolysis liquor. Based on these results, a process for producing purified lignin and precipitates of volatile compounds was proposed.

  17. Complexes of 3.6 kDa Maltodextrin with Some Metals

    Directory of Open Access Journals (Sweden)

    Christopher H. Schilling

    2004-06-01

    Full Text Available Preparation of magnesium, lanthanum, and bismuth(III complexes of 3.6 kDa maltodextrin and some properties of the resulting materials are presented. The metal derivatives contain metals bound to the oxygen atoms of the hydroxyl groups of maltodextrin. Additionally, the metal atoms are coordinated to the hydroxyl groups of the D-glucose units of the macroligand. Such coordination stabilized the metal – oxygen bond against hydrolysis, even in boiling water. The presence of magnesium and lanthanum atoms increased the thermal stability of maltodextrin, whereas bismuth atoms decreased it.

  18. Influence of relativistic effects on hydrolysis of Ra2+

    International Nuclear Information System (INIS)

    Zielinska, B.; Bilewicz, A.

    2005-01-01

    Using 224 Ra radiotracer the first hydrolysis constant (pK 1h ) of Ra 2+ cations has been determined. The pK 1h value of Ra 2+ was compared with the pK 1h values of other Group 2 cations. It has been shown that the electrostatic hydrolysis model based on assumption that pK 1h is a linear function of reciprocal ionic radii (1/r i ) does not describe well the hydrolysis of Group 2 metal cations. The reason of higher Ra 2+ hydrolysis as expected is the influence of relativistic effects on bonding 7s and 7p 1/2 orbitals. (author)

  19. Hydrolysis-extraction of apple proto pectins in dynamic mode

    International Nuclear Information System (INIS)

    Bobodzhonova, G.N.; Gorshkova, R.M.; Makhkamov, Kh.K.

    2013-01-01

    The article describes a hydrolysis process of apple husks by using dynamics regime of hydrolysis. It's shown that application of dynamics method positively influences on the pectin yields and its main parameters. It was defined that by dynamics regime of hydrolysis-extraction of apple husks it is possible to obtain qualitative products with high yield at a mild ph value of medium of hydrolysing agent.

  20. Angle resolved x-ray photoelectron spectroscopy (ARXPS) analysis of lanthanum oxide for micro-flexography printing

    Energy Technology Data Exchange (ETDEWEB)

    Hassan, S., E-mail: suhaimihas@uthm.edu.my; Yusof, M. S., E-mail: mdsalleh@uthm.edu.my; Maksud, M. I., E-mail: midris1973@gmail.com [Faculty of Mechanical and Manufacturing Engineering, Universiti Tun Hussein Onn Malaysia, 86400 Batu Pahat, Johor (Malaysia); Embong, Z., E-mail: zaidi@uthm.edu.my [Faculty of Science, Technology and Human Development, Universiti Tun Hussein Onn Malaysia, 86400 Batu Pahat, Johor (Malaysia)

    2016-01-22

    Micro-flexography printing was developed in patterning technique from micron to nano scale range to be used for graphic, electronic and bio-medical device on variable substrates. In this work, lanthanum oxide (La{sub 2}O{sub 3}) has been used as a rare earth metal candidate as depositing agent. This metal deposit was embedded on Carbon (C) and Silica (Si) wafer substrate using Magnetron Sputtering technique. The choose of Lanthanum as a target is due to its wide application in producing electronic devices such as thin film battery and printed circuit board. The La{sub 2}O{sub 3} deposited on the surface of Si wafer substrate was then analyzed using Angle Resolve X-Ray Photoelectron Spectroscopy (ARXPS). The position for each synthetic component in the narrow scan of Lanthanum (La) 3d and O 1s are referred to the electron binding energy (eV). The La 3d narrow scan revealed that the oxide species of this particular metal is mainly contributed by La{sub 2}O{sub 3} and La(OH){sub 3}. The information of oxygen species, O{sup 2-} component from O 1s narrow scan indicated that there are four types of species which are contributed from the bulk (O{sup 2−}), two chemisorb component (La{sub 2}O{sub 3}) and La(OH){sub 3} and physisorp component (OH). Here, it is proposed that from the adhesive and surface chemical properties of La, it is suitable as an alternative medium for micro-flexography printing technique in printing multiple fine solid lines at nano scale. Hence, this paper will describe the capability of this particular metal as rare earth metal for use in of micro-flexography printing practice. The review of other parameters contributing to print fine lines will also be described later.

  1. Angle resolved x-ray photoelectron spectroscopy (ARXPS) analysis of lanthanum oxide for micro-flexography printing

    Science.gov (United States)

    Hassan, S.; Yusof, M. S.; Embong, Z.; Maksud, M. I.

    2016-01-01

    Micro-flexography printing was developed in patterning technique from micron to nano scale range to be used for graphic, electronic and bio-medical device on variable substrates. In this work, lanthanum oxide (La2O3) has been used as a rare earth metal candidate as depositing agent. This metal deposit was embedded on Carbon (C) and Silica (Si) wafer substrate using Magnetron Sputtering technique. The choose of Lanthanum as a target is due to its wide application in producing electronic devices such as thin film battery and printed circuit board. The La2O3 deposited on the surface of Si wafer substrate was then analyzed using Angle Resolve X-Ray Photoelectron Spectroscopy (ARXPS). The position for each synthetic component in the narrow scan of Lanthanum (La) 3d and O 1s are referred to the electron binding energy (eV). The La 3d narrow scan revealed that the oxide species of this particular metal is mainly contributed by La2O3 and La(OH)3. The information of oxygen species, O2- component from O 1s narrow scan indicated that there are four types of species which are contributed from the bulk (O2-), two chemisorb component (La2O3) and La(OH)3 and physisorp component (OH). Here, it is proposed that from the adhesive and surface chemical properties of La, it is suitable as an alternative medium for micro-flexography printing technique in printing multiple fine solid lines at nano scale. Hence, this paper will describe the capability of this particular metal as rare earth metal for use in of micro-flexography printing practice. The review of other parameters contributing to print fine lines will also be described later.

  2. HYDROLYSIS OF CHEESEWHEY PROTEINSWITH TRYPSIN, CHYMOTRYPSINAND CARBOXYPEPTIDASEA

    Directory of Open Access Journals (Sweden)

    M. F. CUSTÓDIO

    2009-01-01

    Full Text Available

    This work presents a method for adding value to cheese whey residues by whey proteins hydrolysis, using trypsin, chymotrypsin and carboxypeptidase A as catalysts. Sweet cheese whey was dialyzed and filtered in kaolin. Lactose and protein contents were analyzed after each step. The activities of bovine pancreas trypsin and chymotrypsin were measured at different pHs and temperatures. The optimal pH for the hydrolysis of whey proteins was 9.0 for both enzymes. Optima temperatures were 60ºC for trypsin, and 50ºC for chymotrypsin. Trypsin exhibited typical Michaelis-Menten behavior, but chymotrypsin did not. Electrophoretic analysis showed that neither trypsin nor chymotrypsin alone hydrolyzed whey proteins in less than three hours. Hydrolysis rates of -lactalbumin by trypsin, and of bovine serum albumin by chymotrypsin were low. When these enzymes were combined, however, all protein fractions were attacked and rates of hydrolysis were enhanced by one order of magnitude. The addition of carboxypeptidase A to the others enzymes did not improve the process yield.

  3. Electron transfer precedes ATP hydrolysis during nitrogenase catalysis.

    Science.gov (United States)

    Duval, Simon; Danyal, Karamatullah; Shaw, Sudipta; Lytle, Anna K; Dean, Dennis R; Hoffman, Brian M; Antony, Edwin; Seefeldt, Lance C

    2013-10-08

    The biological reduction of N2 to NH3 catalyzed by Mo-dependent nitrogenase requires at least eight rounds of a complex cycle of events associated with ATP-driven electron transfer (ET) from the Fe protein to the catalytic MoFe protein, with each ET coupled to the hydrolysis of two ATP molecules. Although steps within this cycle have been studied for decades, the nature of the coupling between ATP hydrolysis and ET, in particular the order of ET and ATP hydrolysis, has been elusive. Here, we have measured first-order rate constants for each key step in the reaction sequence, including direct measurement of the ATP hydrolysis rate constant: kATP = 70 s(-1), 25 °C. Comparison of the rate constants establishes that the reaction sequence involves four sequential steps: (i) conformationally gated ET (kET = 140 s(-1), 25 °C), (ii) ATP hydrolysis (kATP = 70 s(-1), 25 °C), (iii) Phosphate release (kPi = 16 s(-1), 25 °C), and (iv) Fe protein dissociation from the MoFe protein (kdiss = 6 s(-1), 25 °C). These findings allow completion of the thermodynamic cycle undergone by the Fe protein, showing that the energy of ATP binding and protein-protein association drive ET, with subsequent ATP hydrolysis and Pi release causing dissociation of the complex between the Fe(ox)(ADP)2 protein and the reduced MoFe protein.

  4. Electron transfer precedes ATP hydrolysis during nitrogenase catalysis

    Science.gov (United States)

    Duval, Simon; Danyal, Karamatullah; Shaw, Sudipta; Lytle, Anna K.; Dean, Dennis R.; Hoffman, Brian M.; Antony, Edwin; Seefeldt, Lance C.

    2013-01-01

    The biological reduction of N2 to NH3 catalyzed by Mo-dependent nitrogenase requires at least eight rounds of a complex cycle of events associated with ATP-driven electron transfer (ET) from the Fe protein to the catalytic MoFe protein, with each ET coupled to the hydrolysis of two ATP molecules. Although steps within this cycle have been studied for decades, the nature of the coupling between ATP hydrolysis and ET, in particular the order of ET and ATP hydrolysis, has been elusive. Here, we have measured first-order rate constants for each key step in the reaction sequence, including direct measurement of the ATP hydrolysis rate constant: kATP = 70 s−1, 25 °C. Comparison of the rate constants establishes that the reaction sequence involves four sequential steps: (i) conformationally gated ET (kET = 140 s−1, 25 °C), (ii) ATP hydrolysis (kATP = 70 s−1, 25 °C), (iii) Phosphate release (kPi = 16 s−1, 25 °C), and (iv) Fe protein dissociation from the MoFe protein (kdiss = 6 s−1, 25 °C). These findings allow completion of the thermodynamic cycle undergone by the Fe protein, showing that the energy of ATP binding and protein–protein association drive ET, with subsequent ATP hydrolysis and Pi release causing dissociation of the complex between the Feox(ADP)2 protein and the reduced MoFe protein. PMID:24062462

  5. Thermoluminescent kinetic parameters of the perovskite, KMgF3, activated with lanthanum

    International Nuclear Information System (INIS)

    Sepulveda M, F.; Azorin N, J.; Rivera M, T.; Furetta, C.; Sanipoli, C.

    2004-01-01

    The thermoluminescent curves induced by the beta radiation in the perovskite KMgF 3 were investigated activated with lanthanum. The classic methods were used to determine the kinetic parameters (the kinetic order b, the activation energy E and the frequency of escape intent s) associated with the peaks of the thermoluminescent curve (Tl) in the KMgF 3 activated with lanthanum after the irradiation with beta rays. The method is based on the position of the thermoluminescent peaks, obtained of the temperature change of the peak in the maximum emission caused by the change in the heating rapidity to which the samples were measured. In this work, the samples in form of pellets were re cooked previously at 400 C during one hour before irradiating them with beta particles. The Tl measures were made with a Tl reader system using three different heating rapidities and storing the glow curves. To calculate the depth of the E traps and the frequency factor s, the parameters of the glow curve were determined experimentally of the shame of the glow curve by means of the mensuration of the shame of the maximum temperature of the peak, T M like a function of the heating rapidity. The results indicate that the values of the kinetic parameters are very near among if when they are obtained indistinctly of anyone of the different methods. (Author)

  6. Hydrolysis of metal ions. Vol. 1 and 2

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Paul L. [Geochem Australia, Kiama, NSW (Australia); Ekberg, Christian [Chalmers Univ. of Technology, Goeteborg (Sweden). Nuclear Chemistry/Industrial Materials Recycling

    2016-07-01

    Filling the need for a comprehensive treatment that covers the theory, methods and the different types of metal ion complexes with water (hydrolysis), this handbook and ready reference is authored by a nuclear chemist from academia and an industrial geochemist. The book includes both cation and anion complexes, and approaches the topic of metal ion hydrolysis by first covering the background, before proceeding with an overview of the dissociation of water and then all different metal-water hydrolysis complexes and compounds. A must-have for scientists in academia and industry working on this interdisciplinary topic.

  7. Discovery of new Praseodymium I energy levels with help of green laser light

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Shamim; Siddiqui, Imran; Tanweer Iqbal, Syed; Windholz, Laurentius [Institute of Experimental Physics, Graz University of Technology, Petersgasse 16, A 8010 Graz (Austria)

    2012-07-01

    The hyperfine structure (hfs) of Praseodymium I spectral lines were experimentally investigated using LIF technique in a hollow cathode discharge lamp. We report here the investigation of 100 spectral lines which resulted in a discovery of 20 new energy levels of even and odd parity. The excitation source is a tunable ring-dye laser system, operated with Coumarin 102. The laser wavelength is tuned to a strong hyperfine component of the investigated spectral line, and fluorescence signals from excited levels are searched. The hfs of the investigated line is recorded by scanning the laser frequency across the investigated region. Magnetic hf interaction constant ''A'' and angular momentum ''J'' of the combining lower and upper levels involved in the formation of the line are evaluated. If one of the combining levels is not known (in most cases upper level), the determined angular momentum ''J'' and hyperfine constant ''A'' are used to identify one of the involved levels (in most cases the lower level) and the energy of the unknown level is determined by using center of mass wave number of line and the energy of the identified level. The level found in this way must explain most of the observed fluorescence wavelengths and the hyperfine structure of the fluorescence lines appearing in FT spectrum.

  8. Magnetoresistance and magnetic ordering in praseodymium and neodymium hexaborides

    International Nuclear Information System (INIS)

    Anisimov, M. A.; Bogach, A. V.; Glushkov, V. V.; Demishev, S. V.; Samarin, N. A.; Filipov, V. B.; Shitsevalova, N. Yu.; Kuznetsov, A. V.; Sluchanko, N. E.

    2009-01-01

    The magnetoresistance Δρ/ρ of single-crystal samples of praseodymium and neodymium hexaborides (PrB 6 and NdB 6 ) has been measured at temperatures ranging from 2 to 20 K in a magnetic field of up to 80 kOe. The results obtained have revealed a crossover of the regime from a small negative magnetoresistance in the paramagnetic state to a large positive magnetoresistive effect in magnetically ordered phases of the PrB 6 and NdB 6 compounds. An analysis of the dependences Δρ(H)/ρ has made it possible to separate three contributions to the magnetoresistance for the compounds under investigation. In addition to the main negative contribution, which is quadratic in the magnetic field (-Δρ/ρ ∝ H 2 ), a linear positive contribution (Δρ/ρ ∝ H) and a nonlinear ferromagnetic contribution have been found. Upon transition to a magnetically ordered state, the linear positive component in the magnetoresistance of the PrB 6 and NdB 6 compounds becomes dominant, whereas the quadratic contribution to the negative magnetoresistance is completely suppressed in the commensurate magnetic phase of these compounds. The presence of several components in the magnetoresistance has been explained by assuming that, in the antiferromagnetic phases of PrB 6 and NdB 6 , ferromagnetic nanoregions (ferrons) are formed in the 5d band in the vicinity of the rareearth ions. The origin of the quadratic contribution to the negative magnetoresistance is interpreted in terms of the Yosida model, which takes into account scattering of conduction electrons by localized magnetic moments of rare-earth ions. Within the approach used, the local magnetic susceptibility χ loc has been estimated. It has been demonstrated that, in the temperature range T N loc for the compounds under investigation can be described with good accuracy by the Curie-Weiss dependence χ loc ∝ (T - Θ p ) -1 .

  9. The origin of current blocking in interfacial conduction in Sr-doped lanthanum gallates

    Science.gov (United States)

    Park, Hee Jung

    2018-02-01

    The grain boundary transport of lanthanum gallate has been studied with various doping concentrations, and the origins of blocking on the grain boundary are compared. La1-xSrxGaO3 samples (x = 0.005, 0.01, 0.05 and 0.1) have been prepared and their bulk (grain) and grain boundary resistances been experimentally measured as a function of temperature (T: 200-550 °C) and oxygen partial pressure (Po2) using ac-impedance measurements. In addition, Hebb-Wagner polarization measurements have been conducted to investigate the electrical conductivity of minor charge carriers in the lanthanum gallates. The grain boundary resistance in the low-doped materials (x = 0.005 and 0.01) increases with increasing Po2 while in the highly-doped materials (x = 0.05, 0.1) it hardly depended on Po2. At lower concentrations conduction is mixed and at higher concentrations is found to be predominantly ionic conductivity. The space charge model successfully describes the mixed conduction at the grain boundary at low-doping, but does not explain the predominant ionic conductivity at high-doping. The origin of blocking at high-doping is explained by the crystallographic asymmetry of the grain boundary with respect to the bulk and/or Sr-segregation.

  10. Improved adaptation of test with lanthanum nitrate for the colorimetric estimation of acetate

    Energy Technology Data Exchange (ETDEWEB)

    Szumilo, T [Akademia Medyczna, Lublin (Poland)

    1976-01-01

    A colorimetric method for the determination of acetate based on the production of the blue complex between iodine and lanthanum alkaline acetate has been developed. Optimum concentrations of reagents (acetate, lanthanum nitrate, iodine and ammonia) as well as the volume of acetate were selected to achieve best colour intensity. Coloured complex was stabilized by dilution of reagent mixture with water to the final volume convenient for determinaton. Absorbance of the complex can be measured immediately after dilution and any changes can be observed during at least 15 minutes. Elevation of temperature over 60/sup 0/decreases absorbance. The method fulfills the Beer's law in the range 1,5-3,5 ..mu..moles of acetate, precision of the method 2/sup +/ = 3,7%. Apart from acetate - propionate and fluoroacetate complex is 620 nm, propionate complex - at 590 nm. Propionate complex displayed any relationship between concentration and absorbance. Potassium, sodium, lithium and barium acetates give the identical results as acetic acid, whereas zinc and cupric acetates failed to react. Other derivatives tested, e.g. chloroacetate, trichloroacetate, iodoacetate, chloroporpionate and butyrate are unable to form the coloured complexes. Many compounds interfere with the formation of acetate complex, therefore, in material containing impurities acetate can be determined after purificaton by means of described in literature methods.

  11. On the stability of the ternary phases in the La-Co-O system and the nonstoichiometry of lanthanum cobaltate

    International Nuclear Information System (INIS)

    Seppaenen, Matti

    1979-01-01

    The crystal structure of La 4 Co 3 O 10 , which is a new ternary phase identified in the present study, was determined by means of X-ray diffraction. It has an orthorhombic symmetry and its space group is most likely Fsub(mmm) (face-centered). On the basis of the thermodynamical studies of the La-Co-O system, the stable ternary phases are LaCoO 3 , La 4 Co 3 O 10 and La 2 CoO 4 . The stability limits of these phases were determined as a function of oxygen activity and temperature, and their molar Gibbs standard formation functions were calculated. Electrons, e', and electron holes, hsup(.), are majority defects in lanthanum cobaltate and their concentrations are exceptionally high and nearly constant in the temperature range 1178 - 1295 K. Under thermodynamically well defined conditions the nonstoichiometry of lanthanum cobaltate was determined as a function of oxygen activity and temperature by coulometric titration. In the oxygen partial pressure and temperature range of the present study the oxygen vacancies were ionic minority defects dependent on the activity of oxygen. Due to the high concentration of electronic defects the oxygen vancancy concentration increases high at low oxygen pressures. Oxygen vacancies behave ideally in lanthanum cobaltate i.e. obey Henry's law when their concentrations are <=0.01. (author)

  12. Effect of Lanthanum as a Promoter on Fe-Co/SiO2 Catalyst for Fischer-Tropsch Synthesis

    Directory of Open Access Journals (Sweden)

    Ali Abbasi

    2014-03-01

    Full Text Available Iron-Cobalt catalyst is well known from both operational and economical aspects for Fischer-Tropsch synthesis. Effort to increase the efficiency of this kind of catalyst is an important research topic. In this work, the effect of lanthanum on characteristic behavior, conversion and selectivity of a Fe-Co/SiO2 Fischer-Tropsch catalyst was studied. The Fe-Co-La/SiO2 Catalysts were prepared using an incipient wetness impregnation method. These catalysts were then characterized by XRF-EDAX, BET and TPR techniques, and their performance were evaluated in a lab-scale reactor at 250ºC, H2/CO = 1.8 of molar ratio, 16 barg pressure and GHSV=600 h-1. TPR analysis showed that the addition of La lowered the reduction temperature of Fe-Co catalyst, and due to a lower temperature, the sintering of the catalyst can be mitigated. Furthermore, from the micro reactor tests (about 4 days, it was found that lanthanum promoted catalyst had higher selectivity toward hydrocarbons, and lower selectivity toward CO2.Received: 8th July 2013; Revised: 18th November 2013; Accepted: 1st December 2013[How to Cite: Abbasi, A., Ghasemi, M., Sadighi, S. (2014. Effect of Lanthanum as a Promoter on Fe-Co/SiO2 Catalyst for Fischer-Tropsch Synthesis. Bulletin of Chemical Reaction Engineering & Catalysis, 9 (1: 23-27. (doi:10.9767/bcrec.9.1.5142.23-27][Permalink/DOI: http://dx.doi.org/10.9767/bcrec.9.1.5142.23-27

  13. Lanthanum chromite colloidal processing; Processamento coloidal de cromito de lantanio

    Energy Technology Data Exchange (ETDEWEB)

    Setz, Luiz Fernando Grespan

    2009-07-01

    Lanthanum chromite (LaCrO{sub 3}) is currently the most studied material for applications such as solid oxide fuel cell inter connector (HTSOFC). The complexity of microstructures and geometries of HTSOFC devices, require a precise control of processing parameters to get the desired combination of properties and this, the use of techniques involving concentrated ceramic slips conformation are appropriate, therefore, is well controlled, assist in obtaining homogeneous parts, reproductive and complex geometries. Thus, studies involving the surface chemistry, the stability conditions and slips flow behaviour in the forming conditions, provide important elements for processes control in the inter connectors manufacture, where more applied settings have slots and channels for the gases passage. Thus, surface chemistry, stability and rheological behaviour of strontium and cobalt doped LaCrO{sub 3} (La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3}) slips prepared with ethanol and water, were studied. The doped lanthanum chromite was produced by combustion synthesis in the IPEN/SP labs. The influence of parameters: p H (water), dispersant concentration, homogenization times and conditions, solid concentration, different ratios binder:plasticizer in the stability and the flow behavior of ceramic suspensions prepared were evaluated. The La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3} products obtained by casting aqueous slips in a plaster mould, using alkaline p H and anionic polyelectrolyte and tapes obtained by using ethanol as a dispersant medium, after sintering at 1600 deg C/4h presented theoretical density > 94%, suitable for use as HTSOFC inter connector. (author)

  14. Direct injection of superheated steam for continuous hydrolysis reaction

    KAUST Repository

    Wang, Weicheng

    2012-09-01

    The primary intent for previous continuous hydrolysis studies was to minimize the reaction temperature and reaction time. In this work, hydrolysis is the first step of a proprietary chemical process to convert lipids to sustainable, drop-in replacements for petroleum based fuels. To improve the economics of the process, attention is now focused on optimizing the energy efficiency of the process, maximizing the reaction rate, and improving the recovery of the glycerol by-product. A laboratory-scale reactor system has been designed and built with this goal in mind.Sweet water (water with glycerol from the hydrolysis reaction) is routed to a distillation column and heated above the boiling point of water at the reaction pressure. The steam pressure allows the steam to return to the reactor without pumping. Direct injection of steam into the hydrolysis reactor is shown to provide favorable equilibrium conditions resulting in a high quality of FFA product and rapid reaction rate, even without preheating the inlet water and oil and with lower reactor temperatures and lower fresh water demand. The high enthalpy of the steam provides energy for the hydrolysis reaction. Steam injection offers enhanced conditions for continuous hydrolysis of triglycerides to high-purity streams of FFA and glycerol. © 2012 Elsevier B.V.

  15. Linking Hydrolysis Performance to Trichoderma reesei Cellulolytic Enzyme Profile

    DEFF Research Database (Denmark)

    Lehmann, Linda Olkjær; Petersen, Nanna; I. Jørgensen, Christian

    2016-01-01

    Trichoderma reesei expresses a large number of enzymes involved in lignocellulose hydrolysis and the mechanism of how these enzymes work together is too complex to study by traditional methods, e.g. by spiking with single enzymes and monitoring hydrolysis performance. In this study a multivariate...... approach, partial least squares regression, was used to see if it could help explain the correlation between enzyme profile and hydrolysis performance. Diverse enzyme mixtures were produced by Trichoderma reesei Rut-C30 by exploiting various fermentation conditions and used for hydrolysis of washed...

  16. Graphite furnace atomic absorption spectrometry with a tantalum boat for the determination of yttrium, samarium, and dysprosium in a mish metal

    International Nuclear Information System (INIS)

    Daidoji, Hidehiro; Tamura, Shohei

    1982-01-01

    The determination of yttrium, samarium, and dysprodium by means of graphite-furnace atomic absorption spectrometry (AAS) was studied by a tantalum boat inserted into a graphite tube atomizer. These elements could not be determined by the use of a commercial graphite tube, In the atomization from a tantalum boat, better analytical sensitivities and negligible memory effects for these rare earths are obtained. The analytical sensitivities of yttrium, samarium, and dysprodium with the tantalum boat were 0.60 ng, 0.86 ng, and 0.17 ng respectively. This method was applied for the determination of yttrium, samarium, and dysprosium in a mish metal. The measurements were performed with slightly acidified solutions (0.01 mol dm 3 HCI or HNO 3 ). The sensitivities and the precisions for these elements decreased with increasing acid concentration. An enhancement in the sensitivities of yttrium and dysprosium upon the addition of a large excess of lanthanum, neodymium, and praseodymium salts were observed. The yttrium, samarium, and dysprosium in a mish metal were determined with both analytical curves of standard solutions containing an excess of lanthanum, cerium, and neodymium ions and of the standard addition. The precisions for this work were in the 3 - 9.3% range. (author)

  17. Promising Ni-Fe-LSGMC anode compatible with lanthanum gallate electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Wang Shizhong [Department of Chemistry, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen, Fujian 361005 (China); School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0245 (United States)], E-mail: shizwang@sohu.com; He, Qiong [Department of Chemistry, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen, Fujian 361005 (China); Liu Meilin [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0245 (United States)], E-mail: meilin.liu@mse.gatech.edu

    2009-06-01

    A number of composite materials in the Ni-Fe-LSGMC family have been studied as potential anodes for solid oxide fuel cells (SOFCs) based on strontium, magnesium, and cobalt doped lanthanum gallate electrolyte (LSGMC). The results show that Ni reacts with LSGMC especially under reducing conditions at high temperatures, resulting in high contact resistance, large electrode polarization, and poor performance. The reaction between Ni and LSGMC depends strongly on the composition and pre-sintering temperature of LSGMC, the concentration of iron in the electrode, and the processing and operating temperatures. Under proper conditions, Ni-Fe-LSGMC5 could be a promising high-performance anode with good compatibility with LSGMC5 electrolyte.

  18. Promising Ni-Fe-LSGMC anode compatible with lanthanum gallate electrolyte

    International Nuclear Information System (INIS)

    Wang Shizhong; He, Qiong; Liu Meilin

    2009-01-01

    A number of composite materials in the Ni-Fe-LSGMC family have been studied as potential anodes for solid oxide fuel cells (SOFCs) based on strontium, magnesium, and cobalt doped lanthanum gallate electrolyte (LSGMC). The results show that Ni reacts with LSGMC especially under reducing conditions at high temperatures, resulting in high contact resistance, large electrode polarization, and poor performance. The reaction between Ni and LSGMC depends strongly on the composition and pre-sintering temperature of LSGMC, the concentration of iron in the electrode, and the processing and operating temperatures. Under proper conditions, Ni-Fe-LSGMC5 could be a promising high-performance anode with good compatibility with LSGMC5 electrolyte.

  19. The systems lanthanum (cerium, samarium) nitrate-tetramethyl-ammonium nitrate-water

    International Nuclear Information System (INIS)

    Zhuravlev, E.F.; Khisaeva, D.A.; Semenova, Eh.B.

    1984-01-01

    The method of cross sections at 25 and 50 deg C has been applied to study solubility in the systems lanthanum nitrate-tetramethyl ammonium nitrate-water (1), cesium (3) nitrate-tetramethyl ammonium nitrate-water (2) and samarium nitrate-tetramethyl ammonium nitrate-water (3). Crystallization fields of congruently dissolving compounds with 1:3 ratio of salt components (in system 1) and 1:2 ratio (in systems 2 and 3) are found in the systems. New solid phases are separated preparatively and subjected to chemical, differential thermal and IR spectroscopic analyses. Compositions of formed compounds are compared with the compositions known for nitrates of other representatives of light lanthanides

  20. Hydrolysis rates of domestic wastewater sludge using biochemical ...

    African Journals Online (AJOL)

    Domestic wastewater treatment can be improved by reducing energy consumption and increasing carbon recovery, which can be achieved using anaerobic digestion of sludge with methane recovery at ambient temperature. Hydrolysis can be a limiting step in anaerobic digestion, and characterisation of hydrolysis rates ...

  1. Kinetic study of sphingomyelin hydrolysis for ceramide production

    DEFF Research Database (Denmark)

    Zhang, Long; Hellgren, Lars; Xu, Xuebing

    2008-01-01

    in cosmetic and pharmaceutical industries such as in hair and skin care products. The enzymatic hydrolysis of sphingomyelin has been proved to be a feasible method to produce ceramide. The kinetic performance of sphingomyelin hydrolysis in the optimal two-phase (water:organic solvent) reaction system...

  2. Cytotoxicity and genotoxicity of a monazite component: lanthanum effects on the viability and induction of breaks in the DNA of human lymphocytes

    International Nuclear Information System (INIS)

    Paiva, Amanda Valle de Almeida

    2007-01-01

    The Monazite is a mineral extracted from open mines. It is constituted by lanthanum element aggregated with cerium, yttrium and thorium [(Ce, La, Y, Th)PO 4 ]. Lanthanum (La) is a rare-earth metal with applications in agriculture, industry and medicine. Since lanthanides and their compounds show a broad spectrum of applications there is an increased risk of incorporation in human. Inhalation of aerosols containing La is the main route of incorporation in workers exposed to several chemical forms of La. Herein, we examined the effect of lanthanum nitrate - La(NO 3 ) 3 in human lymphocytes. JURKAT cells and human peripheral lymphocytes (HPL) were used to evaluate the effect of La(NO 3 ) 3 on viability (apoptosis or necrosis) and DNA strand breaks induction or/and alkali-labile sites (ALS). We demonstrate that La has a cytotoxic and genotoxic effect on both cell lines. The results indicate that necrosis is the pathway by which La(NO 3 ) 3 induces cytotoxicity. The vitamin E is able to diminish DNA strand breaks induced by La(NO 3 ) 3 suggesting that reactive oxygen species (ROS) may be involved in the genotoxic process. (author)

  3. Gamma-induced radiation polymerization of kaolin composite for sorption of lanthanum, europium and uranium ions from low-grade monazite leachate

    International Nuclear Information System (INIS)

    Metwally, S.S.; Hassan, R.S.; El-Masry, E.H.; Borai, E.H.

    2018-01-01

    Gamma radiation polymerization method was used for the modification of kaolin to produce (poly acrylamide-acrylic acid)-Kaolin (PAM-AA-K). Monazite ore is one of the main resources of uranium and lanthanide elements, therefore, this work focused on sorption of uranium, lanthanum and europium ions from low grade monazite leachate. The removal percent for Eu 3+ , La 3+ and UO 2 2+ are 94.6, 91.6 and 73.4%, respectively. Monolayer capacity of Eu 3+ , La 3+ and UO 2 2+ were found to be 54.64, 45.87 and 37.59 mg/g, respectively. The sorption mechanism of lanthanum and europium ions on PAM-AA-K composite mainly takes place as Ln(OH) 2+ , and for uranium as uranyl ion, UO 2 2+ . (author)

  4. Enhanced hydrolysis of cellulose hydrogels by morphological modification.

    Science.gov (United States)

    Alfassi, Gilad; Rein, Dmitry M; Cohen, Yachin

    2017-11-01

    Cellulose is one of the most abundant bio-renewable materials on earth, yet the potential of cellulosic bio-fuels is not fully exploited, primarily due to the high costs of conversion. Hydrogel particles of regenerated cellulose constitute a useful substrate for enzymatic hydrolysis, due to their porous and amorphous structure. This article describes the influence of several structural aspects of the cellulose hydrogel on its hydrolysis. The hydrogel density was shown to be directly proportional to the cellulose concentration in the initial solution, thus affecting its hydrolysis rate. Using high-resolution scanning electron microscopy, we show that the hydrogel particles in aqueous suspension exhibit a dense external surface layer and a more porous internal network. Elimination of the external surface layer accelerated the hydrolysis rate by up to sixfold and rendered the process nearly independent of cellulose concentration. These findings may be of practical relevance to saccharification processing costs, by reducing required solvent quantities and enzyme load.

  5. Analysis of the elements sputtered during the lanthanum implantation in stainless steels

    International Nuclear Information System (INIS)

    Ager, F.J.; Respaldiza, M.A.; Silva, M.F. da; Redondo, L.M.; Soares, J.C.

    1998-01-01

    The evidence of the modification of the surface structure of the AISI-304 stainless steel during the implantation of lanthanum makes the analysis of the sputtered elements very interesting. Those sputtered elements are deposited on a carbon sheet placed in front of the steel being implanted, and studied by means of RBS and PIXE, together with the implanted specimens. Besides, the protective effect of the implanted ions during the high temperature oxidation is also studied by those techniques together with XRD and thermogravimetric methods. (orig.)

  6. Vaporization and diffusion studies on the stability of doped lanthanum gallates

    Energy Technology Data Exchange (ETDEWEB)

    Stanislowski, M.; Singheiser, L.; Hilpert, K. [Research Center Juelich, Institute for Materials and Processes in Energy Systems, IWV-2, 52425 Juelich (Germany); Peck, D.H.; Woo, S.K. [Korea Institute of Energy Research, 71-2 Jang-Dong, Yuseong, 305-343 Daejeon (Korea); Schulz, O.; Martin, M. [RWTH Aachen University, Institute of Physical Chemistry, Landoltweg 2, 52056 Aachen (Germany)

    2006-07-15

    Vaporization and diffusion determine the stability of doped lanthanum gallates under SOFC operating conditions. Systematic vaporization studies of Ga and other elements were carried out using the vapor transpiration method. It was shown that the Ga vaporization is controlled by diffusion from the bulk to the surface. Diffusion coefficients D{sub Ga} and vaporization coefficients {alpha}{sub Ga} were determined by fitting the measured vaporization data to a vaporization model. Secondary phases formed as a result of the vaporization were detected. The influence of different doping levels of Sr, Mg and Fe on the Ga vaporization was elucidated. Moreover, cation self-diffusion of {sup 139}La, {sup 84}Sr and {sup 25}Mg as well as cation impurity diffusion of {sup 144}Nd, {sup 89}Y and {sup 56}Fe in polycrystalline samples of doped lanthanum gallate were directly determined for the composition La{sub 0.9}Sr{sub 0.1}Ga{sub 0.9}Mg{sub 0.1}O{sub 2.9} as an example, from diffusion profiles determined by SIMS. It was found that diffusion occurs by means of bulk and grain boundaries. The bulk diffusion coefficients are similar for all cations with activation energies which are strongly dependent on temperature. The results are explained by a frozen-in defect structure at low temperatures in the ABO{sub 3} perovskite lattice and by proposing a defect cluster containing cation vacancies in the A and B sublattices, as well as oxygen vacancies. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

  7. Effect of protonation on the mechanism of phosphate monoester hydrolysis and comparison with the hydrolysis of nucleoside triphosphate in biomolecular motors.

    Science.gov (United States)

    Hassan, Hammad Ali; Rani, Sadaf; Fatima, Tabeer; Kiani, Farooq Ahmad; Fischer, Stefan

    2017-11-01

    Hydrolysis of phosphate groups is a crucial reaction in living cells. It involves the breaking of two strong bonds, i.e. the O a H bond of the attacking water molecule, and the PO l bond of the substrate (O a and O l stand for attacking and leaving oxygen atoms). Mechanism of the hydrolysis reaction can proceed either by a concurrent or a sequential mechanism. In the concurrent mechanism, the breaking of O a H and PO l bonds occurs simultaneously, whereas in the sequential mechanism, the O a H and PO l bonds break at different stages of the reaction. To understand how protonation affects the mechanism of hydrolysis of phosphate monoester, we have studied the mechanism of hydrolysis of protonated and deprotonated phosphate monoester at M06-2X/6-311+G**//M06-2X/6-31+G*+ZPE level of theory (where ZPE stands for zero point energy). Our calculations show that in both protonated and deprotonated cases, the breaking of the water O a H bond occurs before the breaking of the PO l bond. Because the two events are not separated by a stable intermediate, the mechanism can be categorized as semi-concurrent. The overall energy barrier is 41kcalmol -1 in the unprotonated case. Most (5/6th) of this is due to the initial breaking of the water O a H bond. This component is lowered from 34 to 25kcalmol -1 by adding one proton to the phosphate. The rest of the overall energy barrier comes from the subsequent breaking of the PO l bond and is not sensitive to protonation. This is consistent with previous findings about the effect of triphosphate protonation on the hydrolysis, where the equivalent protonation (on the γ-phosphate) was seen to lower the barrier of breaking the water O a H bond and to have little effect on the PO l bond breaking. Hydrolysis pathways of phosphate monoester with initial breaking of the PO l bond could not be found here. This is because the leaving group in phosphate monoester cannot be protonated, unlike in triphosphate hydrolysis, where protonation of the

  8. Study of lanthanum aluminate for cost effective electrolyte material for SOFC

    Science.gov (United States)

    Verma, O. N.; Shahi, A. K.; Singh, P.

    2018-05-01

    The perovskite type electrolyte material LaAlO3 (abbreviated LAO) has been prepared by easy processing of auto-combustion synthesis using lanthanum nitrate and aluminium nitrate salts as precursors and citric acid as the fuel. The XRD analysis reveals that as synthesized material exhibits only single phase having rhombohedral structure. The measured density and theoretical density have been deliberated. The temperature dependent electrical conductivity of LAO increases with increasing the temperature which leads to increased mobility of oxide ion. The major contribution of such a significant value of ionic conductivity of LAO can be inferred to grain boundary resistance.

  9. Relaxation features of the Young's modulus and internal friction of lanthanum

    International Nuclear Information System (INIS)

    Bodryakov, V.Yu.

    1993-01-01

    E Young module and Q -1 inner friction of polycrystalline lanthanum specimens are studied comprehensively within 4.2-420 K temperature range using bend autovibrations of a specimen represented by a thin rod within ∼ 1-2 kHz frequency range. Three maximums of relaxation nature innner friction are detected under ∼ 380-410, 250-270 and 90-120 K temperatures with 0.29, 0.21 and 0.02 eV activation energies, respectively, on Q -1 (T) curves. Maximums of inner friction are accompanied by peculiarities of E(T) Young module behaviour. 21 refs., 3 figs., 2 tabs

  10. Study of binding properties of lanthanum to wheat roots by INAA

    International Nuclear Information System (INIS)

    Zhang, Z.Y.; Li, F.L.; Xiao, H.Q.; Chai, Z.F.; Xu, L.; Liu, N.

    2004-01-01

    Chemical behavior of lanthanum in root tips excized from wheat seedlings growing at both promotional and inhibitory levels of LaCl 3 in culture solutions was investigated by a sequential leaching procedure combined with instrumental neutron activation analysis. The results indicate that most of La exists in non-exchangeable species and the binding of La 3+ to the root tips is extremely stable. The root tips during growing at the inhibitory level of LaCl 3 absorb much more La than those at the promotional level. However, the La proportion in each fraction is similar for both groups. (author)

  11. Electron paramagnetic resonance of V4+ in the lanthanum and cerium orthophosphates

    International Nuclear Information System (INIS)

    Lima, J.C. de.

    1983-11-01

    The Electron Paramagnetic Resonance (EPR) spectrum of V 4+ was investigated in polycrystalline samples of lanthanum orthophosphate (LaPO 4 ) and cerium orthophosphate (CePO 4 ) doped with 0.2 wt % vanadium pentoxide (V 2 O 5 ). Measurements were performed at room temperature and 9.5 GHz. In LaPO 4 , two non-equivalent axial sites were inferred from the EPR spectra. The most stable of these two sites is probably substitutional. In CePO 4 , a single axial spectrum was observed. It was attributed to V 4+ in substitutional sites. A central, wide line was also seen; it was attributed to ferromagnetic clusters of vanadium ions. Photoacoustic absorption spectra were also recorded for the two compounds. The EPR and photoacoustic absorption data, when analyzed using the molecular orbital theory, show that for both lanthanum orthophosphate and cerium orthophosphate the ground orbital (d sub(x) 2 sub(-y) 2) of the unpainred electron is purely ionic, while the excited orbitals d sub(xy) and d sub(xz,yz) are partly covalent. The degree of covalency is higher for the d sub(xy) orbital. Finally, it should be pointed out that part of the theory used for the interpretation of the EPR and photoacoustic absorption spectra (study of the ligand field splitting of a d orbital in a site of distorted capped antiprism structure) was developed by the author in the present work and is therefore an original contribution. (Author) [pt

  12. Hydrolysis of isocyanic acid on SCR catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Elsener, M; Kleemann, M; Koebel, M [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1999-08-01

    Standard SCR catalysts possess high activity for the hydrolysis of HNCO and thus explain the suitability of urea as a selective reducing agent for NO{sub x}. At high space velocities HNCO-slip can get perceptible over the entire temperature range. This can be attributed to the fact that the temperature dependence is strong for the SCR reaction, but weak for the hydrolysis reaction. (author) 3 figs., 5 refs.

  13. Glucose obtained from rice bran by ultrasound-assisted enzymatic hydrolysis

    Directory of Open Access Journals (Sweden)

    Raquel Cristine Kuhn

    2015-05-01

    Full Text Available In this work ultrasound-assisted solid-state enzymatic hydrolysis of rice bran to obtain fermentable sugars was investigated. For this purpose, process variables such as temperature, enzyme concentration and moisture content were evaluated during the enzymatic hydrolysis with and without ultrasound irradiation. The enzyme used is a blend of amylases derived from genetically modified strains of Trichoderma reesei. Kinetic of the enzymatic hydrolysis of rice bran at the constant-reaction rate period were measured. The best results for the ultrasound-assisted enzymatic hydrolysis was obtained using 3 wt% of enzyme, 60 oC and moisture content of 65 wt%, yielding 0.38 g sugar/g rice bran, whereas for the hydrolysis in the absence of ultrasound the highest yield was 0.20 g sugar/g rice bran using 3 wt% of enzyme, 60 oC and moisture content of 50 wt%. The use of ultrasound-assisted enzymatic hydrolysis of rice bran was intensified, obtaining around 74% more fermentable sugar than in the absence, showing that the use of ultrasound is a promising technology to be used in enzymatic reaction as an alternative of process intensification.

  14. Hydrolysis of dilute acid-pretreated cellulose under mild hydrothermal conditions.

    Science.gov (United States)

    Chimentão, R J; Lorente, E; Gispert-Guirado, F; Medina, F; López, F

    2014-10-13

    The hydrolysis of dilute acid-pretreated cellulose was investigated in a conventional oven and under microwave heating. Two acids--sulfuric and oxalic--were studied. For both hydrothermal conditions (oven and microwave) the resultant total organic carbon (TOC) values obtained by the hydrolysis of the cellulose pretreated with sulfuric acid were higher than those obtained by the hydrolysis of the cellulose pretreated with oxalic acid. However, the dicarboxylic acid exhibited higher hydrolytic efficiency towards glucose. The hydrolysis of cellulose was greatly promoted by microwave heating. The Rietveld method was applied to fit the X-ray patterns of the resultant cellulose after hydrolysis. Oxalic acid preferentially removed the amorphous region of the cellulose and left the crystalline region untouched. On the other hand, sulfuric acid treatment decreased the ordering of the cellulose by partially disrupting its crystalline structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Starch hydrolysis modeling: application to fuel ethanol production.

    Science.gov (United States)

    Murthy, Ganti S; Johnston, David B; Rausch, Kent D; Tumbleson, M E; Singh, Vijay

    2011-09-01

    Efficiency of the starch hydrolysis in the dry grind corn process is a determining factor for overall conversion of starch to ethanol. A model, based on a molecular approach, was developed to simulate structure and hydrolysis of starch. Starch structure was modeled based on a cluster model of amylopectin. Enzymatic hydrolysis of amylose and amylopectin was modeled using a Monte Carlo simulation method. The model included the effects of process variables such as temperature, pH, enzyme activity and enzyme dose. Pure starches from wet milled waxy and high-amylose corn hybrids and ground yellow dent corn were hydrolyzed to validate the model. Standard deviations in the model predictions for glucose concentration and DE values after saccharification were less than ± 0.15% (w/v) and ± 0.35%, respectively. Correlation coefficients for model predictions and experimental values were 0.60 and 0.91 for liquefaction and 0.84 and 0.71 for saccharification of amylose and amylopectin, respectively. Model predictions for glucose (R2 = 0.69-0.79) and DP4+ (R2 = 0.8-0.68) were more accurate than the maltotriose and maltose for hydrolysis of high-amylose and waxy corn starch. For yellow dent corn, simulation predictions for glucose were accurate (R2 > 0.73) indicating that the model can be used to predict the glucose concentrations during starch hydrolysis.

  16. Effects of Dredging and Lanthanum-Modified Clay on Water Quality Variables in an Enclosure Study in a Hypertrophic Pond

    Directory of Open Access Journals (Sweden)

    Miquel Lürling Guido Waajen

    2017-05-01

    Full Text Available An enclosure experiment was conducted between July and September 2009 to compare the effectiveness of a phosphate fixative, the lanthanum-modified bentonite clay Phoslock® (LMB, dredging, and their combination in controlling eutrophication in a hypertrophic urban pond in Heesch, The Netherlands. In total, 25 water quality variables were monitored. Multivariate analysis revealed that the combination LMB-treated and dredged enclosures deviated most from the pond (reference and the controls, and showed the strongest eutrophication reduction. Overall, dredging significantly increased transparency, lowered turbidity, and improved the oxygen conditions in the enclosures compared to non-dredged ones. Nonetheless, one dredged enclosure deviated dramatically from the others, which might reflect methodological issues with dredging. The LMB treatment appeared to be less effective at mitigating eutrophication than dredging, and phosphate concentrations even increased during the experiment in the LMB-treated enclosures. Chemical equilibrium modeling suggested that humic substances could have formed complexes with lanthanum (La from the LMB, rendering it unavailable for intercepting P over the course of the enclosure experiment. Residual lanthanum concentrations in combination dredging and LMB treatments exceeded the Dutch standard 10-fold. Total zooplankton abundance, and particularly Cladocera, increased in all enclosures over the course of the experiment. The limited effect of LMB in the enclosure experiment and the violation of the Dutch La standard when combined with dredging disqualify LMB as an intervention agent in the restoration of the pond.

  17. Direct injection of superheated steam for continuous hydrolysis reaction

    KAUST Repository

    Wang, Weicheng; Turner, Timothy L.; Roberts, William L.; Stikeleather, Larry F.

    2012-01-01

    The primary intent for previous continuous hydrolysis studies was to minimize the reaction temperature and reaction time. In this work, hydrolysis is the first step of a proprietary chemical process to convert lipids to sustainable, drop

  18. Furfural production from fruit shells by acid-catalyzed hydrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Demirbas, A. [Selcuk Univ., Konya (Turkey). Dept. of Chemical Engineering

    2006-01-21

    Pentosans are hydrolyzed to pentoses by dilute mineral acid hydrolysis. The main source of pentosans is hemicelluloses. Furfural can be produced by the acid hydrolysis of pentosan from fruit shells such as hazelnut, sunflower, walnut, and almond of agricultural wastes. Further dehydration reactions of the pentoses yield furfural. The hydrolysis of each shell sample was carried out in dilute sulfuric acid (0.05 to 0.200 mol/l), at high temperature (450-525 K), and short reaction times (from 30 to 600 s). (author)

  19. Phosphate binding therapy in dialysis patients: focus on lanthanum carbonate

    Directory of Open Access Journals (Sweden)

    Ismail A Mohammed

    2008-11-01

    Full Text Available Ismail A Mohammed, Alastair J HutchisonManchester Institute of Nephrology and Transplantation, Manchester Royal Infirmary, Oxford Road, Manchester, UKAbstract: Hyperphosphatemia is an inevitable consequence of end stage chronic kidney disease and is present in the majority of dialysis patients. Recent observational data has associated hyperphosphatemia with increased cardiovascular mortality among dialysis patients. Dietary restriction of phosphate and current dialysis prescription practices are not enough to maintain serum phosphate levels within the recommended range so that the majority of dialysis patients require oral phosphate binders. Unfortunately, conventional phosphate binders are not reliably effective and are associated with a range of limitations and side effects. Aluminium-containing agents are highly efficient but no longer widely used because of well established and proven toxicity. Calcium based salts are inexpensive, effective and most widely used but there is now concern about their association with hypercalcemia and vascular calcification. Sevelamer hydrochloride is associated with fewer adverse effects, but a large pill burden and high cost are limiting factors to its wider use. In addition, the efficacy of sevelamer as a monotherapy in lowering phosphate to target levels in severe hyperphosphatemia remains debatable. Lanthanum carbonate is a promising new non-aluminium, calcium-free phosphate binder. Preclinical and clinical studies have demonstrated a good safety profile, and it appears well tolerated and effective in reducing phosphate levels in dialysis patients. Its identified adverse events are apparently mild to moderate in severity and mostly GI related. It appears to be effective as a monotherapy, with a reduced pill burden, but like sevelamer, it is significantly more expensive than calcium-based binders. Data on its safety profile over 6 years of treatment are now available.Keywords: hyperphosphatemia, lanthanum

  20. Combined enzymatic hydrolysis and fermentation of hemicellulose to 2,3-butanediol

    Energy Technology Data Exchange (ETDEWEB)

    Yu, E.K.C.; Deschatelets, L.; Saddler, J.N.

    1984-06-01

    Hemicellulose-rich fractions from several agricultural residues were converted to 2,3-butanediol by a combined enzymatic hydrolysis and fermentation process. Culture filtrates from Trichoderma harzianum E58 were used to hydrolyze the substrates while Klebsiella pneumoniae fermented the liberated sugars to 2,3-butanediol. Approximately 50-60% of a 5% (w/v) xylan preparation could be hydrolyzed and quantitatively converted to 2,3-butanediol using this procedure. Although enzymatic hydrolysis was optimal at pH 5.0 and 50/sup 0/C, the combined hydrolysis and fermentation was most efficient at pH 6.5 and 30/sup 0/C. Combined hydrolysis and fermentation resulted in butanediol levels that were 20-40% higher than could be obtained with a separate hydrolysis and fermentation process. The hemicellulose-rich water-soluble fractions obtained from a variety of steam-exploded agricultural residues could be readily used by the combined hydrolysis and fermentation approach resulting in butanediol yields of 0.4-0.5 g/g of reducing sugar utilized.

  1. STRUCTURE AND THERMAL STABILITY OF THE BENZO-15-CROWN-5 WITH LANTHANUM (III BROMIDE COMPLEX

    Directory of Open Access Journals (Sweden)

    Muhammad Idiris Saleh

    2010-06-01

    Full Text Available The reaction of benzo-15-crown-5 (C14H20O5 ligand with La(NO33.7H2O in the presence of HBr has resulted in the production of an exotic sandwich complex, [LaC28H36Br4O10][3Br]. The crystal system is triclinic with space group P1, a = 12.5834(14 Å, b = 13.5816(16 Å, c = 13.8403(16 Å, a = 70.751(2°, b = 66.773(2° and g = 67.631(2°. The cation comprises of the lanthanum atom coordinated to two crowns via three oxygen atoms from each crown in a η3-sandwich fashion. The two phenyl groups of the crown are brominated. The La-OLigand bond lengths are between 2.857(7 and 2.949(7 Å. The trianion [3Br]3- is linear with Br-Br bond lengths of 2.518(2 and 2.560(2 Å respectively. The molecule is stabilized by intermolecular interactions of the type C-H...Br to form dimers and are arranged parallel to bc face.  Keywords: lanthanum, benzo-15-crown-5, hydrogen bonding, bromination, x-ray structure

  2. On isomorphous substitution of calcium by sodium and lanthanum in synthetic hydroxyapatite

    International Nuclear Information System (INIS)

    Get'man, E.I.; Kanyuka, Yu.V.; Loboda, S.N.

    1998-01-01

    Isomorphous substitution of calcium by sodium and lanthanum in synthetic hydroxyapatite Ca 5-2x La x (PO 4 ) 3 OH by x=0-2.5 within the temperature range 1100-800 deg C is studied through the roentgenophase analysis and IR-spectroscopy methods. It is established that singlephase solid solutions are formed in the area of x≥0.4 by a≤0.4 there exist phases with LaPO 4 , LaNa 6 (PO 4 ) 3 structures and unknown phase along with solid solution of the apatite structure

  3. Characterization of phosphate sequestration by a lanthanum modified bentonite clay: A solid-state NMR, EXAFS and PXRD study

    DEFF Research Database (Denmark)

    Dithmer, Line; Lipton, Andrew S; Reitzel, Kasper

    2015-01-01

    Phosphate (Pi) sequestration by a lanthanum (La) exchanged clay mineral (La-Bentonite), which is extensively used in chemical lake restoration, was investigated on the molecular level using a combination of 31P and 139La solid state NMR spectroscopy (SSNMR), extended X-ray absorption spectroscopy...

  4. Hydrolysis of diacylglycerols by lipoprotein lipase.

    Science.gov (United States)

    Morley, N H; Kuksis, A; Buchnea, D; Myher, J J

    1975-05-10

    Enantiomeric diacylglycerols were emulsified, mole for mole, with lyso(1-acyl) lecithin and were hydrolyzed with lipoprotein lipase in NH4Cl-beef serum albumin buffer at pH 8.6 after a brief incubation with delipidated rat serum. The enzyme was prepared from lyophilized and dialyzed bovine skim milk in a 4 percent solution. The course of hydrolysis for each set of enantiomers was determined by gas-liquid chromatography of the masses of the diacylglycerols remaining or monoacylglycerols released in the medium between 0 and 15 min. The majority of sets of sn-1,2- and 2,3-diacylglycerols, including an isotope-labeled true enantiomeric set which was assessed by mass spectrometry, demonstrated preference by the enzyme for lipolysis at position 1 but with less specificity than previously was shown in sn-triacylglycerol hydrolysis. The results preclude the possibility that the predominance of sn-2,3-diacylglycerol intermediates during triacylglycerol hydrolysis is due solely to a preferential breakdown of the 1,2-isomers and reinforce the conclusion that lipoprotein lipase is specific for position 1.

  5. Equidensitometry: a method for characterising the structure of plasmas. Qualitative characterisation of the lanthanum d.c. arc by equidensitometry of monochromatic arc photographs

    International Nuclear Information System (INIS)

    Dittrich, K.; Niebergall, K.; Roessler, H.

    1976-01-01

    A new method has been developed for the experimental characterization of d.c. arc plasmas. The method consists of the combination of the spectral photography of d.c. arc plasmas with a slitless, stigmatic plane-grating spectrograph and the characterization of the photographs with the aid of photographic equidensitometry. The principles of the method are described. The method is used for the investigation of a lanthanum d.c. arc plasma. The qualitative results of the measurements of the axial distributions of the light emission and lanthanum and calcium particle concentrations in the arc are discussed. The limitations and shortcomings of the method are pointed out. (author)

  6. Heteropoly acid catalyzed hydrolysis of glycogen to glucose

    International Nuclear Information System (INIS)

    Klein, Miri; Pulidindi, Indra Neel; Perkas, Nina; Gedanken, Aharon

    2015-01-01

    Complete conversion of glycogen to glucose is achieved by using H 3 PW 12 O 40 ·nH 2 O (HPW) and H 4 SiW 12 O 40 ·nH 2 O (HSiW) as catalysts for the hydrolysis under optimized hydrothermal conditions (mass fraction of catalyst 2.4%, 373 K and 2 h reaction time). The reusability of the catalyst (HPW) was demonstrated. In addition to carrying out the glycogen hydrolysis in an autoclave, other novel methods such as microwave irradiation and sonication have also been investigated. At higher mass fraction of the heteropoly acids (10.5%), glycogen could be completely converted to glucose under microwave irradiation. Sonication of an aqueous solution of glycogen in the presence of HPW and HSiW also yielded glucose. Thus, heteropoly acids are efficient, environmentally friendly and reusable catalysts for the conversion of glycogen to glucose. - Highlights: • Hydrothermal, microwave and sonication based methods of hydrolysis. • Heteropoly acids are green catalysts for glycogen hydrolysis. • Glycogen from cyanobacteria is demonstrated as a potential feedstock for glucose

  7. Potentiometric measurement of polymer-membrane electrodes based on lanthanum

    Energy Technology Data Exchange (ETDEWEB)

    Saefurohman, Asep, E-mail: saefurohman.asep78@Gmail.com; Buchari,, E-mail: saefurohman.asep78@Gmail.com; Noviandri, Indra, E-mail: saefurohman.asep78@Gmail.com [Department of Chemistry, Bandung Institute of Technology (Indonesia); Syoni [Department of Metallurgy Engineering, Bandung Institute of Technology (Indonesia)

    2014-03-24

    Quantitative analysis of rare earth elements which are considered as the standard method that has a high accuracy, and detection limits achieved by the order of ppm is inductively coupled plasma atomic emission spectroscopy (ICPAES). But these tools are expensive and valuable analysis of the high cost of implementation. In this study be made and characterized selective electrode for the determination of rare earth ions is potentiometric. Membrane manufacturing techniques studied is based on immersion (liquid impregnated membrane) in PTFE 0.5 pore size. As ionophores to be used tri butyl phosphate (TBP) and bis(2-etylhexyl) hydrogen phosphate. There is no report previously that TBP used as ionophore in polymeric membrane based lanthanum. Some parameters that affect the performance of membrane electrode such as membrane composition, membrane thickness, and types of membrane materials studied in this research. Manufacturing of Ion Selective Electrodes (ISE) Lanthanum (La) by means of impregnation La membrane in TBP in kerosene solution has been done and showed performance for ISE-La. FTIR spectrum results for PTFE 0.5 pore size which impregnated in TBP and PTFE blank showed difference of spectra in the top 1257 cm{sup −1}, 1031 cm{sup −1} and 794.7 cm{sup −1} for P=O stretching and stretching POC from group −OP =O. The result showed shift wave number for P =O stretching of the cluster (−OP=O) in PTFE-TBP mixture that is at the peak of 1230 cm{sup −1} indicated that no interaction bond between hydroxyl group of molecules with molecular clusters fosforil of TBP or R{sub 3}P = O. The membrane had stable responses in pH range between 1 and 9. Good responses were obtained using 10{sup −3} M La(III) internal solution, which produced relatively high potential. ISE-La showed relatively good performances. The electrode had a response time of 29±4.5 second and could be use for 50 days. The linear range was between 10{sup −5} and 10{sup −1} M.

  8. Acid hydrolysis of Biomass lignocellulose Onopordum nervosum Boiss

    International Nuclear Information System (INIS)

    Suarez Contreras, C.; Diaz Palma, A.; Paz, M. D.

    1985-01-01

    Hydrolysis of resistant cellulose of Onopordum nervosum Boiss (thistle) to reducing sugars in dilute sulfuric acid in glass ampoules and long residence times has been studied and kinetic parameters determined. The rate of hydrolysis is similar to that of the cellulose of Douglas fir, but comparatively the effect of the acid is more pronounced than temperature. From kinetic data it can be pre ducted the yield and since it can be obtained at least 45% of the potential glucose (48% as reducing sugars) at 190 degree centigree, 1,6% acid and 6,1 min. residence time, it indicates that the continuous acid hydrolysis of thistle may be a process of commercial interest. (Author) 18 refs

  9. Study on the technology of compound enzymatic hydrolysis of whole passion fruit

    Science.gov (United States)

    Yang, Yu-xia; Duan, Zhen-hua; Kang, Chao; Zhu, Xiang-hao; Li, Ding-jin

    2017-12-01

    Fresh Whole Passion Fruit was used as raw material, The enzymatic hydrolysis technology of Passion Fruit by Complex enzyme were studied, The effects of enzyme dosage, Enzyme ratio(cellulose: pectinase), pH, temperature and time on the hydrolysis were investigated by single-tests and orthogonal tests, the hydrolysis indicators of single-factor tests and orthogonal tests were juice yield. The optimal hydrolysis conditions of Passion Fruit by Complex enzyme were enzyme dosage 0.12%, Enzyme ratio 5:1, hydrolysis temperature 50°C, pH4.0 and time 3.5 h. Under such conditions, juice yield of Passion Fruit was 92.91%.

  10. Radiation-induced degradation and subsequent hydrolysis of waste cellulose materials

    International Nuclear Information System (INIS)

    Kumakura, M.; Kaetsu, I.

    1979-01-01

    The effect of γ-pre-irradiation of cellulose in cellulose containing waste plants was investigated through enzymatic and acidic hydrolysis reaction. Pre-irradiation of waste rice straw, chaff and saw dust accelerated the enzymatic hydrolysis by cellulase. Reducing sugar and glucose yields were higher with an increasing radiation dose in these materials. The required dose for effective acceleration of enzymatic hydrolysis was much reduced by the addition of chlorine during radiation. However, reducing sugar and glucose yields in the subsequent acidic hydrolysis of waste products decreased through pre-irradiation treatment. This was attributed to an acceleration effect of a secondary acidic decomposition of sugar to lower molecular weight-products through pre-irradiation. (author)

  11. Radiation-induced degradation and subsequent hydrolysis of waste cellulose materials

    Energy Technology Data Exchange (ETDEWEB)

    Kumakura, M; Kaetsu, I [Japan Atomic Energy Research Inst., Takasaki, Gunma. Takasaki Radiation Chemistry Research Establishment

    1979-03-01

    The effect of ..gamma..-pre-irradiation of cellulose in cellulose containing waste plants was investigated through enzymatic and acidic hydrolysis reaction. Pre-irradiation of waste rice straw, chaff and saw dust accelerated the enzymatic hydrolysis by cellulase. Reducing sugar and glucose yields were higher with an increasing radiation dose in these materials. The required dose for effective acceleration of enzymatic hydrolysis was much reduced by the addition of chlorine during radiation. However, reducing sugar and glucose yields in the subsequent acidic hydrolysis of waste products decreased through pre-irradiation treatment. This was attributed to an acceleration effect of a secondary acidic decomposition of sugar to lower molecular weight-products through pre-irradiation.

  12. Radiation-induced degradation and subsequent hydrolysis of waste cellulose materials

    Energy Technology Data Exchange (ETDEWEB)

    Kamakura, M; Kaetsu, I

    1979-03-01

    The effect of gamma-pre-irradiation of cellulose in cellulose-containing waste plants was investigated through enzymatic and acidic hydrolysis reaction. Pre-irradiation of waste rice straw, chaff and saw dust accelerated the enzymatic hydrolysis by cellulase. Reducing sugar and glucose yields were higher with an increasing radiation dose in these materials. The required dose for effective acceleration of enzymatic hydrolysis was much reduced by the addition of chlorine during radiation. However, reducing sugar and glucose yields in the subsequent acidic hydrolysis of waste products decreased through pre-irradiation treatment. This was attributed to an acceleration effect of a secondary acidic decomposition of sugar to lower molecular weight-products through pre-irradiation.

  13. Chemical analysis and base-promoted hydrolysis of locally ...

    African Journals Online (AJOL)

    Abstract. The study was on the chemical analysis and base- promoted hydrolysis of extracted shea nut fat. The local method of extraction of the shea nut oil was employed in comparison with literature report. A simple cold-process alkali hydrolysis of the shea nut oil was used in producing the soap. The chemical analysis of ...

  14. Temperature dependence of magnetoresistance in lanthanum manganite ceramics

    International Nuclear Information System (INIS)

    Gubkin, M.K.; Zalesskii, A.V.; Perekalina, T.M.

    1996-01-01

    Magnetoresistivity in the La0.9Na0.1Mn0.9(V,Co)0.1O3 and LaMnO3+δ ceramics was studied. The temperature dependence of magnetoresistance in these specimens was found to differ qualitatively from that in the La0.9Na0.1MnO3 single crystal (the magnetoresistance value remains rather high throughout the measurement range below the Curie temperature), with the maximum values being about the same (20-40% in the field of 20 kOe). Previously published data on magnetization, high frequency magnetic susceptibility, and local fields at the 139La nuclei of the specimens with similar properties attest to their magnetic inhomogeneity. The computation of the conductivity of the nonuniformly ordered lanthanum manganite was performed according to the mean field theory. The calculation results allow one to interpret qualitatively various types of experimental temperature dependences of magnetoresistance

  15. Photocatalytic degradation of the Paracetamol drug using Lanthanum doped ZnO nanoparticles and their in-vitro cytotoxicity assay

    International Nuclear Information System (INIS)

    Shakir, Mohammad; Faraz, Mohd; Sherwani, Mohd Asif; Al-Resayes, Saud I.

    2016-01-01

    The doping of semiconductor by rare earth metals nanoparticles is an effective way for increasing photocatalytic activity. Zinc oxide and Lanthanum doped Zinc oxide nanoparticles were synthesized by modifying the gel-combustion method. It was found that La can greatly enhance the cytotoxicity and photocatalytic activity of ZnO nanoparticles towards various cell lines and Paracetamol drug. These nanoparticles were characterized by various spectroscopic and other techniques which clearly revealed the presence of lanthanum ions. The absorption edge shifts towards the visible region after doping with La ions. This shift shows that the doping of La ions is favorable for absorbing the visible light. The comparative photocatalytic and cytotoxicity activity revealed that La doped ZnO nanoparticles remarkably enhanced activities as compared to the ZnO nanoparticles. The outcome of these studies offers valuable for planning La doped ZnO nanoparticles having cytotoxicity and photocatalytic activities helpful for the formulation of anticancer product and waste water remediation.

  16. Photocatalytic degradation of the Paracetamol drug using Lanthanum doped ZnO nanoparticles and their in-vitro cytotoxicity assay

    Energy Technology Data Exchange (ETDEWEB)

    Shakir, Mohammad, E-mail: shakir078@yahoo.com [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India); Faraz, Mohd [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India); Sherwani, Mohd Asif [Interdisciplinary Biotechnology Unit, Aligarh Muslim University, Aligarh 202002 (India); Al-Resayes, Saud I. [Department of Chemistry, College of Science, King Saud University, Riyadh 11451 (Saudi Arabia)

    2016-08-15

    The doping of semiconductor by rare earth metals nanoparticles is an effective way for increasing photocatalytic activity. Zinc oxide and Lanthanum doped Zinc oxide nanoparticles were synthesized by modifying the gel-combustion method. It was found that La can greatly enhance the cytotoxicity and photocatalytic activity of ZnO nanoparticles towards various cell lines and Paracetamol drug. These nanoparticles were characterized by various spectroscopic and other techniques which clearly revealed the presence of lanthanum ions. The absorption edge shifts towards the visible region after doping with La ions. This shift shows that the doping of La ions is favorable for absorbing the visible light. The comparative photocatalytic and cytotoxicity activity revealed that La doped ZnO nanoparticles remarkably enhanced activities as compared to the ZnO nanoparticles. The outcome of these studies offers valuable for planning La doped ZnO nanoparticles having cytotoxicity and photocatalytic activities helpful for the formulation of anticancer product and waste water remediation.

  17. The influence of lake water alkalinity and humic substances on particle dispersion and lanthanum desorption from a lanthanum modified bentonite

    DEFF Research Database (Denmark)

    Reitzel, Kasper; Balslev, Kristiane Astrid; Jensen, Henning S

    2017-01-01

    A 12 days laboratory study on potential desorption of Lanthanum (La) from a commercial La modified clay (Phoslock) was conducted using lake water from 17 Danish lakes with alkalinities between 0.02 and 3.7 meq L-1and varying concentrations of DOC and humic acids (HA's). A similar study...... was conducted in artificial lake water with alkalinities from 0 to 2.5 meq L-1in order to exclude interference from dissolved HA's. To test if La in solution (FLa) was associated with fine particles, the water samples were filtered sequentially through three filter sizes (1.2 μm, 0.45 μm and 0.2 μm...... at low alkalinities. In addition, this study showed that HA's seem to increase the FLa concentrations in soft water lakes, most likely through complexation of La retained in the Phoslock matrix. In summary, we conclude that elevated La concentrations in lake water after a Phoslock treatment should only...

  18. Multivariate data analysis of enzyme production for hydrolysis purposes

    DEFF Research Database (Denmark)

    Schmidt, A.S.; Suhr, K.I.

    1999-01-01

    of the structure in the data - possibly combined with analysis of variance (ANOVA). Partial least squares regression (PLSR) showed a clear connection between the two differentdata matrices (the fermentation variables and the hydrolysis variables). Hence, PLSR was suitable for prediction purposes. The hydrolysis...

  19. Research and determination of process parameters of milk lactose hydrolysis

    OpenAIRE

    Калинина, Елена Дмитриевна; Коваленко, Александр Владимирович

    2014-01-01

    The researches of enzymatic milk lactose hydrolysis by using the β - galactosidase enzyme are given in the paper. For carrying out a lactose hydrolysis, two β-galactosidase enzyme preparations GODO-YNL2 and Neolactase are offered. For setting lactose hydrolysis parameters, the influence of a pH medium, temperature, enzyme preparation doses, the duration of hydrolyzing the milk lactose affected by the β- galactosidase enzyme preparations, was studied. In terms of effectiveness, adaptability an...

  20. Hydrolysis of the amorphous cellulose in cotton-based paper.

    Science.gov (United States)

    Stephens, Catherine H; Whitmore, Paul M; Morris, Hannah R; Bier, Mark E

    2008-04-01

    Hydrolysis of cellulose in Whatman no. 42 cotton-based paper was studied using gel permeation chromatography (GPC), electrospray ionization-mass spectrometry (ESI-MS), and uniaxial tensile testing to understand the course and kinetics of the reaction. GPC results suggested that scission reactions passed through three stages. Additionally, the evolution of soluble oligomers in the ESI-MS data and the steady course of strength loss showed that the hydrolysis reaction occurred at a constant rate. These findings are explained with a more detailed description of the cellulose hydrolysis, which includes multiple chain scissions on amorphous segments. The breaks occur with increasing frequency near the ends of amorphous segments, where chains protrude from crystalline domains. Oligomers unattached to crystalline domains are eventually created. Late-stage reactions near the ends of amorphous segments produce a kinetic behavior that falsely suggests that hydrolysis had ceased. Monte Carlo simulations of cellulose degradation corroborated the experimental findings.

  1. Synthesis of supermacroporous cryogel for bioreactors continuous starch hydrolysis.

    Science.gov (United States)

    Guilherme, Ederson Paulo Xavier; de Oliveira, Jocilane Pereira; de Carvalho, Lorendane Millena; Brandi, Igor Viana; Santos, Sérgio Henrique Sousa; de Carvalho, Gleidson Giordano Pinto; Cota, Junio; Mara Aparecida de Carvalho, Bruna

    2017-11-01

    A bioreactor was built by means of immobilizing alpha-amylase from Aspergillus oryzae by encapsulation, through cryopolymerization of acrylamide monomers for the continuous starch hydrolysis. The starch hydrolysis was evaluated regarding pH, the concentration of immobilized amylase on cryogel, the concentration of starch solution and temperature. The maximum value for starch hydrolysis was achieved at pH 5.0, concentration of immobilized enzyme 111.44 mg amylase /g cryogel , concentration of starch solution 45 g/L and temperature of 35°C. The immobilized enzyme showed a conversion ratio ranging from 68.2 to 97.37%, depending on the pH and temperature employed. Thus, our results suggest that the alpha-amylase from A. oryzae immobilized on cryogel monoliths represents a potential process for industrial production of maltose from starch hydrolysis. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Hydrolysis of aluminum dross material to achieve zero hazardous waste

    International Nuclear Information System (INIS)

    David, E.; Kopac, J.

    2012-01-01

    Highlights: ► The hydrolysis of aluminum dross in tap water generates pure hydrogen. ► Aluminum particles from dross are activated by mechanically milling technique. ► The process is completely greenhouse gases free and is cleanly to environment. ► Hydrolysis process leads to recycling of waste aluminum by hydrogen production. - Abstract: A simple method with high efficiency for generating high pure hydrogen by hydrolysis in tap water of highly activated aluminum dross is established. Aluminum dross is activated by mechanically milling to particles of about 45 μm. This leads to removal of surface layer of the aluminum particles and creation of a fresh chemically active metal surface. In contact with water the hydrolysis reaction takes place and hydrogen is released. In this process a Zero Waste concept is achieved because the other product of reaction is aluminum oxide hydroxide (AlOOH), which is nature-friendly and can be used to make high quality refractory or calcium aluminate cement. For comparison we also used pure aluminum powder and alkaline tap water solution (NaOH, KOH) at a ratio similar to that of aluminum dross content. The rates of hydrogen generated in hydrolysis reaction of pure aluminum and aluminum dross have been found to be similar. As a result of the experimental setup, a hydrogen generator was designed and assembled. Hydrogen volume generated by hydrolysis reaction was measured. The experimental results obtained reveal that aluminum dross could be economically recycled by hydrolysis process with achieving zero hazardous aluminum dross waste and hydrogen generation.

  3. Mechanistic kinetic models of enzymatic cellulose hydrolysis-A review.

    Science.gov (United States)

    Jeoh, Tina; Cardona, Maria J; Karuna, Nardrapee; Mudinoor, Akshata R; Nill, Jennifer

    2017-07-01

    Bioconversion of lignocellulose forms the basis for renewable, advanced biofuels, and bioproducts. Mechanisms of hydrolysis of cellulose by cellulases have been actively studied for nearly 70 years with significant gains in understanding of the cellulolytic enzymes. Yet, a full mechanistic understanding of the hydrolysis reaction has been elusive. We present a review to highlight new insights gained since the most recent comprehensive review of cellulose hydrolysis kinetic models by Bansal et al. (2009) Biotechnol Adv 27:833-848. Recent models have taken a two-pronged approach to tackle the challenge of modeling the complex heterogeneous reaction-an enzyme-centric modeling approach centered on the molecularity of the cellulase-cellulose interactions to examine rate limiting elementary steps and a substrate-centric modeling approach aimed at capturing the limiting property of the insoluble cellulose substrate. Collectively, modeling results suggest that at the molecular-scale, how rapidly cellulases can bind productively (complexation) and release from cellulose (decomplexation) is limiting, while the overall hydrolysis rate is largely insensitive to the catalytic rate constant. The surface area of the insoluble substrate and the degrees of polymerization of the cellulose molecules in the reaction both limit initial hydrolysis rates only. Neither enzyme-centric models nor substrate-centric models can consistently capture hydrolysis time course at extended reaction times. Thus, questions of the true reaction limiting factors at extended reaction times and the role of complexation and decomplexation in rate limitation remain unresolved. Biotechnol. Bioeng. 2017;114: 1369-1385. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  4. Solid-phase extraction (SPE) of Iron using Lanthanum Silicate ion exchange

    International Nuclear Information System (INIS)

    Kiarostami, V.; Husain, W.

    2002-01-01

    Solid-phase extraction (SPE) is gaining wide use as an effective and speedy technique which reduces solvent usage, disposal costs and extraction time. The analyte is adsorbed from solution onto a solid adsorbent, which is followed by elution of the analyte with a solvent appropriate for instrumental analysis. However, there is an increasing need for new selective adsorbents to expand the area of this technique. Lanthanum silicate ion exchanger, which shows unusual selectivity elements and in this study, it was employed to develop a SPE method for iron ion. Special experiments such as determination of distribution coefficient for iron ion in different solvent systems have been determined

  5. Cerium-modified Aurivillius-type sodium lanthanum bismuth titanate with enhanced piezoactivities

    International Nuclear Information System (INIS)

    Wang Chunming; Zhao Liang; Wang Jinfeng; Zheng Limei; Du Juan; Zhao Minglei; Wang Chunlei

    2009-01-01

    The electrical, piezoelectric and dielectric properties of cerium-modified Aurivillius-type sodium lanthanum bismuth titanate (Na 0.5 La 0.5 Bi 4 Ti 4 O 15 , NLBT) ceramics were investigated. It was found the piezoelectric activities of NLBT ceramics were significantly improved by cerium modification. The piezoelectric coefficient d 33 and Curie temperature T c for the 0.50 wt.% cerium-modified NLBT were found to be 29 pC/N and 573 deg. C, respectively. The reasons for piezoelectric activities improvement by cerium modification were given. A small dielectric abnormity was observed in NLBT ceramics, which can be suppressed by cerium modification.

  6. Enhanced electrocaloric analysis and energy-storage performance of lanthanum modified lead titanate ceramics for potential solid-state refrigeration applications.

    Science.gov (United States)

    Zhang, Tian-Fu; Huang, Xian-Xiong; Tang, Xin-Gui; Jiang, Yan-Ping; Liu, Qiu-Xiang; Lu, Biao; Lu, Sheng-Guo

    2018-01-10

    The unique properties and great variety of relaxer ferroelectrics make them highly attractive in energy-storage and solid-state refrigeration technologies. In this work, lanthanum modified lead titanate ceramics are prepared and studied. The giant electrocaloric effect in lanthanum modified lead titanate ceramics is revealed for the first time. Large refrigeration efficiency (27.4) and high adiabatic temperature change (1.67 K) are achieved by indirect analysis. Direct measurements of electrocaloric effect show that reversible adiabatic temperature change is also about 1.67 K, which exceeds many electrocaloric effect values in current direct measured electrocaloric studies. Both theoretical calculated and direct measured electrocaloric effects are in good agreements in high temperatures. Temperature and electric field related energy storage properties are also analyzed, maximum energy-storage density and energy-storage efficiency are about 0.31 J/cm 3 and 91.2%, respectively.

  7. Effect of lead dioxide on the radiation decomposition of hydrated lanthanum nitrate (Preprint No. RES-05)

    International Nuclear Information System (INIS)

    Patil, S.F.; Bedekar, A.G.; Chiplunkar, N.R.

    1988-02-01

    The rate of radiation induced decomposition of lanthanum nitrate is found to increase in the presence of lead dioxide as a heterophase impurity. Further, the rate also increases with increasing mole percent of the oxide. The results are explained on the basis of energy transfer processes taking place at the interface between nitrate and oxide crystals. (aut hor). 9 refs

  8. Optimization of dilute acid hydrolysis of Enteromorpha

    Science.gov (United States)

    Feng, Dawei; Liu, Haiyan; Li, Fuchao; Jiang, Peng; Qin, Song

    2011-11-01

    Acid hydrolysis is a simple and direct way to hydrolyze polysaccharides in biomass into fermentable sugars. To produce fermentable sugars effectively and economically for fuel ethanol, we have investigated the hydrolysis of Enteromorpha using acids that are typically used to hydrolyze biomass: H2SO4, HCl, H3PO4 and C4H4O4 (maleic acid). 5%(w/w) Enteromorpha biomass was treated for different times (30, 60, and 90 min) and with different acid concentrations (0.6, 1.0, 1.4, 1.8, and 2.2%, w/w) at 121°C. H2SO4 was the most effective acid in this experiment. We then analyzed the hydrolysis process in H2SO4 in detail using high performance liquid chromatography. At a sulfuric acid concentration of 1.8% and treatment time of 60 min, the yield of ethanol fermentable sugars (glucose and xylose) was high, (230.5 mg/g dry biomass, comprising 175.2 mg/g glucose and 55.3 mg/g xylose), with 48.6% of total reducing sugars being ethanol fermentable. Therefore, Enteromorpha could be a good candidate for production of fuel ethanol. In future work, the effects of temperature and biomass concentration on hydrolysis, and also the fermentation of the hydrolysates to ethanol fuel should be focused on.

  9. Hydrolysis of TBF and TiAP in presence of zirconium

    International Nuclear Information System (INIS)

    Vladimirova, M.V.; Kulikov, I.A.; Kuprij, A.A.

    1992-01-01

    Acid hydrolysis of organic solutions of tributyl phosphate (TBP) and tri-iso-amylphosphate (TiAP) in n-paraffin diluent in the presence of zirconium (0.025-0.1 mole/l) at nitric acid concentration of 0.3-1 mole/l is studied. Hydrolysis of extractants in a two-phase system, modelling conditions of spent fuel reprocessing and consisting of 1.1 mole/l TAP, 3 mole/l nitric acid at zirconium concentration in water phase 0.05-0.11 mole/l, at water-organic phase ratio 10:1 and at 60 deg C is also studied. Constants of TAP hydrolysis in organic and water phases are determined. Mechanism of increasing the TAP hydrolysis rate in zirconium presence is discussed. 5 refs., 2 figs., 5 tabs

  10. Enzymatic hydrolysis of pretreated barley and wheat straw

    DEFF Research Database (Denmark)

    Rosgaard, Lisa

    2007-01-01

    . The work involved evaluation of 1) possible ways to increase the glucose release from the commercial cellulase product Celluclast by boosting with other enzyme activities to increase the enzymatic hydrolysis, 2) comparing differently pretreated feedstock substrates and 3) evaluating a fed-batch substrate...... mixture resulted in a glucose release corresponding to ~84 % of the glucose release from Celluclast. It was therefore suggested that other enzyme activities than the 4 four main cellulase activities in Celluclast are necessary for optimal hydrolysis of lignocellulose. Even though Celluclast...... is a multicomponent cellulase mixture, there are still possibilities for further improvement in terms of providing the most efficient cellulase mixture for lignocellulose hydrolysis. It was shown that substrates evaluated all had some residual hemicellulose in the solid cellulose fraction after pretreatment...

  11. Base hydrolysis and hydrothermal processing of PBX-9404

    International Nuclear Information System (INIS)

    Flesner, R.L.; Spontarelli, T.; Dell'Orco, P.C.; Sanchez, J.A.

    1994-01-01

    Base hydrolysis in combination with hydrothermal processing has been proposed as an environmentally acceptable alternative to open burning/open detonation for degradation and destruction of high explosives. In this report, the authors examine gaseous and aqueous products of base hydrolysis of the HMX-based plastic bonded explosive, PBX-9404. They also examined products from the subsequent hydrothermal treatment of the base hydrolysate. The gases produced from hydrolysis of PBX-9404 are ammonia, nitrous oxide, and nitrogen. Major aqueous products are sodium formate, acetate, nitrate, and nitrite, but not all carbon products have been identified. Hydrothermal processing of base hydrolysate destroyed up to 98% of the organic carbon in solution, and higher destruction efficiencies are possible. Major gas products detected from hydrothermal processing were nitrogen and nitrous oxide

  12. The optimization of soybean oil hydrolysis reaction research

    International Nuclear Information System (INIS)

    Hasnisa Hashim; Jumat Salimon

    2008-01-01

    The hydrolysis reaction of soybean oil was optimized. The concentration effect of ethanolic alkaline solution (KOH and NaOH) to the oil acidity was studied. The alkaline concentrations, reaction time and temperature factors was investigated during the optimization of the hydrolysis or saponification reaction. KOH solution of 1 M showed a good saponification activity which resulted oil acid value of 226.8 mg/ g compared to NaOH solution with acid value of 225.4 mg/ g for the same reaction. The optimum saponification reaction of soybean oil occurred at 60 degree Celsius in 30 minutes by using ethanolic KOH 1 M with acid value of 229.6 mg/ g. Composition of free fatty acid before and after hydrolysis were determined by using gas chromatography. (author)

  13. Study on the influence of optical electronegativity of fluoride host structures on the crystal field components' position of the [Xe]4f{sup 1}5d{sup 1}-configuration of trivalent praseodymium; Untersuchungen zum Einfluss optischer Elektronegativitaet fluoridischer Wirtsstrukturen auf die Position der Kristallfeldkomponenten der [Xe]4f{sup 1}5d{sup 1}-Konfiguration von trivalentem Praseodym

    Energy Technology Data Exchange (ETDEWEB)

    Herden, Benjamin

    2014-03-15

    As alternative radiation sources for mercury containing lamps LEDs cover the normal range, but efficient alternatives for UV radiations are still not available. Xenon excimer discharge lamps could be candidate as alternatives to mercury low-pressure discharge lamps. The discharge wavelength of these lamps is 172 nm that has to be converted in other spectral ranges. The theses deals with trivalent praseodymium as activator ion in binary and ternary fluoride host structures. The host structure and the crystallographic position of the praseodymium ion influence the development of emissions line and bands and the energetic position of the emission. The results are explained by the interaction of the nephelauxetic effect and the crystal field splitting of 5d orbitals, called optical electronegativity.

  14. Comparison of the economics of acid and enzymatic hydrolysis of newsprint

    Energy Technology Data Exchange (ETDEWEB)

    Grethlein, H E

    1978-04-01

    In order to compare the process economics of making glucose from cellulose, a plant design is presented using acid hydrolysis which can be compared with a published design using enzyme hydrolysis. A common design basis is used; namely, an input capacity of 885 ton/day newsprint with a common technique of cost estimation. The cost of making glucose is in the range of 1.75 to 2.45 cents/lb, depending on the slurry concentration fed to the reactor for the acid hydrolysis. This cost range is less than the published estimate of 5.2 cents/lb for enzymatic hydrolysis.

  15. Electronic Conductivity of Doped-Lanthanum Gallate Electrolytes

    Science.gov (United States)

    Yamaji, Katsuhiko; Xiong, Yue Ping; Kishimoto, Haruo; Horita, Teruhisa; Sakai, Natsuko; Brito, Manuel E.; Yokokawa, Harumi

    Electronic conductivity of doped lanthanum gallate electrolytes were determined by using a Hebb-Wagner type polarization cell. Electronic conductivity of cobalt-doped, La0.8Sr0.2Ga0.8Mg0.15Co0.5O3-δ (LSGMC), and non cobalt-doped, La0.8Sr0.2Ga0.8Mg0.2O2.8 (LSGM8282), were measured as a function of oxygen partial pressures. The electronic conductivity of LSGM8282 showed a linear dependence on p(O2)1/4 in the higher p(O2) region, which is attributed to the electronic hole conductivity. The electronic conductivity of LSGMC showed a linear dependence on p(O2)1/6 in the higher p(O2) region. LSGMC has higher electronic conductivity than LSGM, and the conductivity was not clearly changed with temperatures between 600 and 800 °C. In lower p(O2) region, the electronic conductivity data have poor reproducibility and did not show any dependence on p(O2) because of the degradation of the electrolytes in severe reducing atmospheres.

  16. Mechanical properties of lanthanum and yttrium chromites

    Energy Technology Data Exchange (ETDEWEB)

    Paulik, S.W.; Armstrong, T.R. [Pacific Northwest National Lab., Richland, WA (United States)

    1996-12-31

    In an operating high-temperature (1000{degrees}C) solid oxide fuel cell (SOFC), the interconnect separates the fuel (P(O{sub 2}){approx}10{sup -16} atm) and the oxidant (P(O2){approx}10{sup 0.2} atm), while being electrically conductive and connecting the cells in series. Such severe atmospheric and thermal demands greatly reduce the number of viable candidate materials. Only two materials, acceptor substituted lanthanum chromite and yttrium chromite, meet these severe requirements. In acceptor substituted chromites (Sr{sup 2+} or Ca{sup 2+} for La{sup 3+}), charge compensation is primarily electronic in oxidizing conditions (through the formation of Cr{sup 4+}). Under reducing conditions, ionic charge compensation becomes significant as the lattice becomes oxygen deficient. The formation of oxygen vacancies is accompanied by the reduction of Cr{sup 4+} ions to Cr{sup 3+} and a resultant lattice expansion. The lattice expansion observed in large chemical potential gradients is not desirable and has been found to result in greatly reduced mechanical strength.

  17. Process development of starch hydrolysis using mixing characteristics of Taylor vortices.

    Science.gov (United States)

    Masuda, Hayato; Horie, Takafumi; Hubacz, Robert; Ohmura, Naoto; Shimoyamada, Makoto

    2017-04-01

    In food industries, enzymatic starch hydrolysis is an important process that consists of two steps: gelatinization and saccharification. One of the major difficulties in designing the starch hydrolysis process is the sharp change in its rheological properties. In this study, Taylor-Couette flow reactor was applied to continuous starch hydrolysis process. The concentration of reducing sugar produced via enzymatic hydrolysis was evaluated by varying operational variables: rotational speed of the inner cylinder, axial velocity (reaction time), amount of enzyme, and initial starch content in the slurry. When Taylor vortices were formed in the annular space, efficient hydrolysis occurred because Taylor vortices improved the mixing of gelatinized starch with enzyme. Furthermore, a modified inner cylinder was proposed, and its mixing performance was numerically investigated. The modified inner cylinder showed higher potential for enhanced mixing of gelatinized starch and the enzyme than the conventional cylinder.

  18. Thermal stability and microstructure of catalytic alumina composite support with lanthanum species

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, Masakuni, E-mail: ozawa@numse.nagoya-u.ac.jp; Nishio, Yoshitoyo

    2016-09-01

    Highlights: • Thermal stability of La-modified γ-Al{sub 2}O{sub 3} with nanometer-scaled structure. • LaAlO{sub 3} particles are dispersed in the aggregated particles of alumina. • Increase of the surface basicity of La modified alumina using CO{sub 2}-TPD. - Abstract: Lanthanum (La) modified γ-alumina composite was examined for application toward thermostable catalytic support at elevated temperature. La added alumina was prepared through an aqueous process using lanthanum (III) nitrate and then characterized by surface area measurement, X-ray powder diffraction (XRD), differential thermal analysis (DTA), scanning electron microscope (SEM), transmission electron microscope (TEM), X-ray photoemission spectroscopy (XPS) and surface desorption of CO{sub 2}. It was found that the properties depended on the La content and heat treatment temperatures. The characterization of the surface, structural and chemical properties of La-Al{sub 2}O{sub 3} showed the existence of a strong interaction between the La species and alumina via formation of new phase and modified surface in Al{sub 2}O{sub 3} samples. LaAlO{sub 3} nanoparticle formed among alumina particles by the solid phase reaction of Al{sub 2}O{sub 3} and La{sub 2}O{sub 3}. The increase of the surface basicity of La modified alumina was demonstrated using CO{sub 2} temperature programmed desorption experiments. The controlled surface interaction between La oxide and alumina provide the unique surface and structural properties of the resulting mixed oxides as catalysts and catalytic supports.

  19. Validation of lignocellulosic biomass carbohydrates determination via acid hydrolysis.

    Science.gov (United States)

    Zhou, Shengfei; Runge, Troy M

    2014-11-04

    This work studied the two-step acid hydrolysis for determining carbohydrates in lignocellulosic biomass. Estimation of sugar loss based on acid hydrolyzed sugar standards or analysis of sugar derivatives was investigated. Four model substrates (starch, holocellulose, filter paper and cotton) and three levels of acid/material ratios (7.8, 10.3 and 15.4, v/w) were studied to demonstrate the range of test artifacts. The method for carbohydrates estimation based on acid hydrolyzed sugar standards having the most satisfactory carbohydrate recovery and relative standard deviation. Raw material and the acid/material ratio both had significant effect on carbohydrate hydrolysis, suggesting the acid to have impacts beyond a catalyst in the hydrolysis. Following optimal procedures, we were able to reach a carbohydrate recovery of 96% with a relative standard deviation less than 3%. The carbohydrates recovery lower than 100% was likely due to the incomplete hydrolysis of substrates, which was supported by scanning electron microscope (SEM) images. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Cellulase hydrolysis of unsorted MSW

    DEFF Research Database (Denmark)

    Jensen, Jacob Wagner; Felby, Claus; Jørgensen, Henning

    2011-01-01

    A recent development in waste management and engineering has shown that the cellulase can be used for the liquefaction of organic fractions in household waste. The focus of this study was to optimize the enzyme hydrolysis of thermally treated municipal solid waste (MSW) by the addition of surfact......A recent development in waste management and engineering has shown that the cellulase can be used for the liquefaction of organic fractions in household waste. The focus of this study was to optimize the enzyme hydrolysis of thermally treated municipal solid waste (MSW) by the addition...... of calcium, potassium, sodium, chloride and others that may affect cellulolytic enzymes. Cellulase performance showed no effect of adding the metal ion-chelating agent EDTA to the solution. The cellulases were stable, tolerated and functioned in the presence of several contaminants....

  1. Influence of tellurite on lifetime for samarium doped lanthanum lead borate glass

    Science.gov (United States)

    Madhu, A.; Eraiah, B.

    2018-04-01

    Samarium substituted tellurium lanthanum lead borate glass is prepared using melt quenching technique. Luminescence spectra have been recorded upon excitation with 402 nm various transitions from 4G5/2 level, for samarium doped tellurite glasses are studied and also lifetime for all the samples exhibit single exponential behaviour of decay curve. Luminescence spectra of present glasses show quenching effect due to cross-relation channels of samarium ions. The lifetime of glass samples decrease as the tellurite concentration is decreased. So, it evidences that to attain longer lifetime for lasing material one can tune the host by selecting concentration of tellurite.

  2. Performance of planar single cell lanthanum gallate based solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Maffei, N.; Kuriakose, A.K. [Materials Technology Labs., CANMET, Natural Resources Canada, Ottawa, ON (Canada)

    1998-09-01

    A novel synthesis of high purity, single phase strontium-magnesium doped lanthanum gallate through a nitrate route is described. The prepared powder is formed into planar monolithic elements by uniaxial pressing followed by isostatic pressing and sintering. XRD analysis of the sintered elements reveal no detectable secondary phases. The performance of the electrolyte in solid oxide fuel cells (SOFC) with three different anode/cathode combinations tested at 700 C with respect to the J-V and power density is reported. The data show that the characteristics of this SOFC are strongly dependent on the particular anode/cathode system chosen. (orig.)

  3. Performance of planar single cell lanthanum gallate based solid oxide fuel cells

    Science.gov (United States)

    Maffei, N.; Kuriakose, A. K.

    A novel synthesis of high purity, single phase strontium-magnesium doped lanthanum gallate through a nitrate route is described. The prepared powder is formed into planar monolithic elements by uniaxial pressing followed by isostatic pressing and sintering. XRD analysis of the sintered elements reveal no detectable secondary phases. The performance of the electrolyte in solid oxide fuel cells (SOFC) with three different anode/cathode combinations tested at 700°C with respect to the J- V and power density is reported. The data show that the characteristics of this SOFC are strongly dependent on the particular anode/cathode system chosen.

  4. Dynamic modeling and validation of a lignocellulosic enzymatic hydrolysis process

    DEFF Research Database (Denmark)

    Prunescu, Remus Mihail; Sin, Gürkan

    2013-01-01

    The enzymatic hydrolysis process is one of the key steps in second generation biofuel production. After being thermally pretreated, the lignocellulosic material is liquefied by enzymes prior to fermentation. The scope of this paper is to evaluate a dynamic model of the hydrolysis process...... on a demonstration scale reactor. The following novel features are included: the application of the Convection–Diffusion–Reaction equation to a hydrolysis reactor to assess transport and mixing effects; the extension of a competitive kinetic model with enzymatic pH dependency and hemicellulose hydrolysis......; a comprehensive pH model; and viscosity estimations during the course of reaction. The model is evaluated against real data extracted from a demonstration scale biorefinery throughout several days of operation. All measurements are within predictions uncertainty and, therefore, the model constitutes a valuable...

  5. Radiation pretreatments of cellulose materials for the enhancement of enzymatic hydrolysis

    International Nuclear Information System (INIS)

    Ait Si Mamar, S.; Hadjadj, A.

    1990-01-01

    The conversion of wheat straw agricultural cellulosic wastes to reducing sugars and glucose has been studied by pretreatments by acid hydrolysis and gamma radiolysis over the dose 0-2 MGy. The pretreatment of cellulosic wastes by gamma radiolysis in the presence of sulfuric acid solution shows that the reducing sugars yield increases with the irradiation dose. The effect of radiation degradation on cellulosic wastes between 0.1 MGy and 2 MGy shows the glucose and reducing sugars yields after enzymatic hydrolysis by cellulase vary with the dose. In the relatively low dose range, up to about 0.5 MGy, the reducing sugars yields vary slightly. For an acid hydrolysis followed by radiation at dose range below 0.5 MGy the reducing sugars yields are practically insensitive to radiation. On the other hand, the pretreatment by radiation in higher dose range from 0.5 to 2 MGy followed by enzymatic hydrolysis is effective for the conversion of cellulosic wastes into glucose. The radiation induced degradation of cellulose into glucose depends on the type of acid hydrolysis and on the enzymatic hydrolysis time by cellulase. Pre-irradiation in air is more effective than in acid solution. (author)

  6. Radiation pretreatments of cellulose materials for the enhancement of enzymatic hydrolysis

    Science.gov (United States)

    Mamar, S. Ait Si; Hadjadj, A.

    The conversion of wheat straw agricultural cellulosic wastes to reduning sugars and glucose has been studied by pretreatments by acid hydrolysis and gamma radiolysis over the dose 0-2 MGy. The pretreatment of cellulosic wastes by gamma radiolysis in the presence of sulfuric acid solution shows that the reducing sugars yield increases with the irradiation dose. The effect of radiation degradation on cellulosic wastes between 0.1 MGy and 2 MGy shows the glucose and reducing sugars yields after enzymatic hydrolysis by cellulase vary with the dose. In the relatively low dose range, up to about 0.5 MGy, the reducing sugars yields vary slightly. For an acid hydrolysis followed by radiation at dose range below 0.5 MGy the reducing sugars yields are practically insensitive to radiation. On the other hand, the pretreatment by radiation in higher dose range from 0.5 to 2 MGy followed by enzymatic hydrolysis is effective for the conversion of cellulosic wastes into glucose. The radiation induced degradation of cellulose into glucose depends on the type of acid hydrolysis and on the enzymatic hydrolysis time by cellulase. Pre-irradiation in air is more effective than in acid solution.

  7. Specific heat studies of lanthanum and yttrium sesquicarbides

    International Nuclear Information System (INIS)

    Cort, B.; Stewart, G.R.; Giorgi, A.L.

    1984-01-01

    The specific heats of the sesquicarbides LaC/sub 1.35/ and La/sub 0.9/Th/sub 0.1/C/sub 1.6/ (prepared by arc melting) and YC/sub 1.35/ (prepared by a high-pressure technique) have been measured for the first time. No bulk specific heat anomaly appears in either lanthanum compounds, even though (1) inductively measured superconducting transition temperatures are respectively high (11.0 K for LaC/sub 1.35/ and 12.7 K for La/sub 0.9/Th/sub 0.1/C/sub 1.6/) and (2) YC/sub 1.35/ is a bulk superconductor with a T/sub c/ = 10.5 K and Y/sub 0.7/Th/sub 0.3/C/sub 1.58/ (also prepared by high pressure) was previously reported to be a bulk superconductor with a T/sub c/ = 17.1 K. The apparent correlation with preparation technique is discussed

  8. Determining the hydrolysis of cations: A short overview

    International Nuclear Information System (INIS)

    Ekberg, Christian; Brown, Paul L.

    2006-01-01

    Full text: The hydrolysis of metal ions is the most fundamental aqueous chemistry. As soon as the metal is introduced to water, dissolution may take place and if the water is pure only hydrolysis reactions will take place. There are several methods used in the literature to determine the stability constants of these reactions, e.g. solvent extraction, potentiometric titrations, ion exchange and solubility measurements. Which one to select is not straight forward. All of them have pros and cons and different regions of applicability with respect to whether they are good for determining the initial hydrolysis or the later stages. Once the constants are determined it is important to assess the uncertainty in the determination. We point out tools to make this straight forward and traceable which is most important in scientific studies. (authors)

  9. Improving Aspergillus carbonarius crude enzymes for lignocellulose hydrolysis

    DEFF Research Database (Denmark)

    Hansen, Gustav Hammerich

    and single enzyme supplementation. Fungal strains were screened in order to determine crude enzyme extracts that could be supplemented as boosters of A. carbonarius own crude enzyme extract, when applied in lignocellulose hydrolysis. The fungi originated from different environmental niches, which all had...... for their potential in hydrolysis of wheat straw both by application of monocultures and by supplementing to crude enzymes of A. carbonarius. For the crude enzymes from solid cultivations there were eight isolates that showed synergistic interaction resulting in doubling and tripling of the glucose release in wheat...... straw hydrolysis. A completely different profile of synergy was observed for crude enzymes from liquid cultivations, as there were only three isolates that enhanced glucose release. Only one of these three isolates had shown synergistic effects when cultivated in a solid medium. The screening...

  10. Enzyme loading dependence of cellulose hydrolysis of sugarcane bagasse

    Directory of Open Access Journals (Sweden)

    Carlos Martín

    2012-01-01

    Full Text Available The enzymatic hydrolysis of steam-pretreated sugarcane bagasse, either delignified or non-delignified, was studied as a function of enzyme loading. Hydrolysis experiments were carried out using five enzyme loadings (2.5 to 20 FPU/g cellulose and the concentration of solids was 2% for both materials. Alkaline delignification improved cellulose hydrolysis by increasing surface area. For both materials, glucose concentrations increased with enzyme loading. On the other hand, enzyme loadings higher than 15 FPU/g did not result in any increase in the initial rate, since the excess of enzyme adsorbed onto the substrate restricted the diffusion process through the structure.

  11. Lanthanum chloride impairs spatial memory through ERK/MSK1 signaling pathway of hippocampus in rats.

    Science.gov (United States)

    Liu, Huiying; Yang, Jinghua; Liu, Qiufang; Jin, Cuihong; Wu, Shengwen; Lu, Xiaobo; Zheng, Linlin; Xi, Qi; Cai, Yuan

    2014-12-01

    Rare earth elements (REEs) are used in many fields for their diverse physical and chemical properties. Surveys have shown that REEs can impair learning and memory in children and cause neurobehavioral defects in animals. However, the mechanism underlying these impairments has not yet been completely elucidated. Lanthanum (La) is often selected to study the effects of REEs. The aim of this study was to investigate the spatial memory impairments induced by lanthanum chloride (LaCl3) and the probable underlying mechanism. Wistar rats were exposed to LaCl3 in drinking water at 0 % (control, 0 mM), 0.25 % (18 mM), 0.50 % (36 mM), and 1.00 % (72 mM) from birth to 2 months after weaning. LaCl3 considerably impaired the spatial learning and memory of rats in the Morris water maze test, damaged the synaptic ultrastructure and downregulated the expression of p-MEK1/2, p-ERK1/2, p-MSK1, p-CREB, c-FOS and BDNF in the hippocampus. These results indicate that LaCl3 exposure impairs the spatial learning and memory of rats, which may be attributed to disruption of the synaptic ultrastructure and inhibition of the ERK/MSK1 signaling pathway in the hippocampus.

  12. Cationic copolymerization of cycloaliphatic epoxy resin with an spirobislactone with lanthanum triflate as initiator

    International Nuclear Information System (INIS)

    Fernandez, Xavier; Ramis, Xavier; Salla, Josep M.

    2005-01-01

    3,4-Epoxycyclohexylmethyl 3,4-epoxycyclohexane carboxylate (ECH) was cured with different proportions of 1,6-dioxaspiro[4,4]nonane-2,7-dione (s(γ-BL)) using lanthanum triflate as a catalyst. DSC was used to obtain kinetic data associated to the curing process by means of series of non-isothermal experiments. Fourier transform infrared spectroscopy in attenuated total reflection mode (FT-IR/ATR) was used to study the evolution of the epoxide group in order to compare experimental isothermal data with simulated isothermal data. The complexity of the process itself enabled us to compare different procedures for obtaining isoconversional data and to determine the kinetic model that best describes the curing process. An increase in the proportion of s(γ-BL) increases the speed of the curing process. By means of applying isoconversional methods to dynamic experimental data, we observed that an increase in the proportion of s(γ-BL) leads to an overall decrease in the activation energy for the different formulations. Kinetic parameters that were determined using both differential and integral isoconversional procedures were compared. This allowed us to analyze and to discuss the usefulness of different methods in order to obtain a suitable kinetic triplet at each step of the curing of the ECH/s(γ-BL) system using lanthanum triflate as a catalyst

  13. CFD simulation of transient stage of continuous countercurrent hydrolysis of canola oil

    KAUST Repository

    Wang, Weicheng

    2012-08-01

    Computational Fluid Dynamic (CFD) modeling of a continuous countercurrent hydrolysis process was performed using ANSYS-CFX. The liquid properties and flow behavior such as density, specific heats, dynamic viscosity, thermal conductivity, and thermal expansivity as well as water solubility of the hydrolysis components triglyceride, diglyceride, monoglyceride, free fatty acid, and glycerol were calculated. Chemical kinetics for the hydrolysis reactions were simulated in this model by applying Arrhenius parameters. The simulation was based on actual experimental reaction conditions including temperature and water-to-oil ratio. The results not only have good agreement with experimental data but also show instantaneous distributions of concentrations of every component in hydrolysis reaction. This model provided visible insight into the continuous countercurrent hydrolysis process. © 2012 Elsevier Ltd.

  14. CFD simulation of transient stage of continuous countercurrent hydrolysis of canola oil

    KAUST Repository

    Wang, Weicheng; Natelson, Robert H.; Stikeleather, Larry F.; Roberts, William L.

    2012-01-01

    Computational Fluid Dynamic (CFD) modeling of a continuous countercurrent hydrolysis process was performed using ANSYS-CFX. The liquid properties and flow behavior such as density, specific heats, dynamic viscosity, thermal conductivity, and thermal expansivity as well as water solubility of the hydrolysis components triglyceride, diglyceride, monoglyceride, free fatty acid, and glycerol were calculated. Chemical kinetics for the hydrolysis reactions were simulated in this model by applying Arrhenius parameters. The simulation was based on actual experimental reaction conditions including temperature and water-to-oil ratio. The results not only have good agreement with experimental data but also show instantaneous distributions of concentrations of every component in hydrolysis reaction. This model provided visible insight into the continuous countercurrent hydrolysis process. © 2012 Elsevier Ltd.

  15. SIMULTANEOUS PRETREATMENT OF LIGNOCELLULOSE AND HYDROLYSIS OF STARCH IN MIXTURES TO SUGARS

    Directory of Open Access Journals (Sweden)

    Hamzeh Hoseinpour

    2010-11-01

    Full Text Available Mixtures of starch and lignocelluloses are available in many industrial, agricultural, and municipal wastes and residuals. In this work, dilute sulfuric acid was used for simultaneous pretreatment of lignocellulose and hydrolysis of starch, to obtain a maximum amount of fermentable sugar after enzymatic hydrolysis with cellulase and β-glucosidase. The acid treatment was carried out at 70-150°C with 0-1% (v/v acid concentration and 5-15% (w/v solids concentration for 0-40 minutes. Under the optimum conditions, obtained at 130°C, 1% acid, and 7.5% solids loading for 30 min, the starch was almost completely converted to glucose. However, the acid treatment was not successful for efficient hydrolysis of pure cellulose. A mixture of pine softwood and potato as representatives of lignocellulosic and starch components, respectively, were treated at the optimum conditions for acid hydrolysis of starch. The dilute-acid treatment resulted in 1.2, 60.5, and 23.6% hydrolysis of glucan, xylan, and mannan of pine wood and 67% of potato starch to fermentable sugars. After the acid treatment, the solid residue of the mixture was subjected to enzymatic hydrolysis. The enzymatic hydrolysis under the optimum conditions resulted in conversion of 76% of the glucan in the treated softwood. Therefore, using acid treatment of the mixture is a promising process for pretreatment of wood in addition to the hydrolysis of starch.

  16. Fabrication of Sr- and Co-doped lanthanum chromite interconnectors for SOFC

    Energy Technology Data Exchange (ETDEWEB)

    Setz, L.F.G. [Departamento de Engenharia de Materiais, Universidade Federal de Sao Carlos - DEMa/UFSCar (Brazil); Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN (Brazil); Santacruz, I. [Departamento de Quimica Inorganica, Cristalografia y Mineralogia, Universidad de Malaga, 29071 Malaga (Spain); Colomer, M.T., E-mail: tcolomer@icv.csic.es [Instituto de Ceramica y Vidrio, ICV (CSIC), 28049 Madrid (Spain); Mello-Castanho, S.R.H. [Instituto de Pesquisas Energeticas e Nucleares - IPEN/CNEN (Brazil); Moreno, R. [Instituto de Ceramica y Vidrio, ICV (CSIC), 28049 Madrid (Spain)

    2011-07-15

    Graphical abstract: FESEM micrographs of the fresh fracture surfaces for the La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3} sintered specimens cast from optimised suspensions with 13.5, 15 and 17.5 vol.% solids loading. Aqueous suspensions were prepared using ammonium polyacrylate (PAA) as dispersant and tetramethylammonium hydroxide (TMAH) to assure a basic pH and providing stabilization. Sintering of the green discs was performed in air at 1600 {sup o}C for 4 h. Highlights: {yields} Optimum casting slips were achieved with 3 wt.% of ammonium polyacrylate and 1 wt.% of tetramethylammonium hydroxide. -- Abstract: Many studies have been performed dealing with the processing conditions of electrodes and electrolytes in solid oxide fuel cells (SOFCs). However, the processing of the interconnector material has received less attention. Lanthanum chromite (LaCrO{sub 3}) is probably the most studied material as SOFCs interconnector. This paper deals with the rheology and casting behaviour of lanthanum chromite based materials to produce interconnectors for SOFCs. A powder with the composition La{sub 0.80}Sr{sub 0.20}Cr{sub 0.92}Co{sub 0.08}O{sub 3} was obtained by combustion synthesis. Aqueous suspensions were prepared to solids loading ranging from 8 to 17.5 vol.%, using ammonium polyacrylate (PAA) as dispersant and tetramethylammonium hydroxide (TMAH) to assure a basic pH and providing stabilization. The influence of the additives concentrations and suspension ball milling time were studied. Suspensions prepared with 24 h ball milling, with 3 wt.% and 1 wt.% of PAA and TMAH, respectively, yielded the best conditions for successful slip casting. Sintering of the green discs was performed in air at 1600 {sup o}C for 4 h leading to relatively dense materials.

  17. Effect of acid hydrolysis on starch structure and functionality: a review.

    Science.gov (United States)

    Wang, Shujun; Copeland, Les

    2015-01-01

    Acid hydrolysis is an important chemical modification that can significantly change the structural and functional properties of starch without disrupting its granular morphology. A deep understanding of the effect of acid hydrolysis on starch structure and functionality is of great importance for starch scientific research and its industrial applications. During acid hydrolysis, amorphous regions are hydrolyzed preferentially, which enhances the crystallinity and double helical content of acid hydrolyzed starch. This review discusses current understanding of the effect of acid hydrolysis on starch structure and functionality. The effects of acid hydrolysis on amylose content, chain length distribution of amylopectin molecules, molecular and crystalline organization (including lamellar structure) and granular morphology are considered. Functional properties discussed include swelling power, gelatinization, retrogradation, pasting, gel texture, and in vitro enzyme digestibility. The paper also highlights some promising applications of acid hydrolyzed starch (starch nanocrystals) in the preparation of biodegradable nanocomposites, bio-hydrogen, and slowly digestible starch-based healthy foods.

  18. Preparations and mechanism of hydrolysis of ([8]annulene)actinide compounds

    International Nuclear Information System (INIS)

    Moore, R.M. Jr.

    1985-07-01

    The mechanism of hydrolysis for bis[8]annulene actinide and lanthanide complexes has been studied in detail. The uranium complex, uranocene, decomposes with good pseudo-first order kinetics (in uranocene) in 1 M degassed solutions of H 2 O in THF. Decomposition of a series of aryl-substituted uranocenes demonstrates that the hydrolysis rate is dependent on the electronic nature of the substituent (Hammett rho value = 2.1, r 2 = 0.999), with electron-withdrawing groups increasing the rate. When D 2 O is substituted for H 2 O, kinetic isotope effects of 8 to 14 are found for a variety of substituted uranocenes. These results suggest a pre-equilibrium involving approach of a water molecule to the central metal, followed by rate determining proton transfer to the eight membered ring and rapid decomposition to products. Each of the four protonations of the complex has a significant isotope effect. The product ratio of cyclooctatriene isomers formed in the hydrolysis varies, depending on the central metal of the complex. However, the general mechanism of hydrolysis, established for uranocene, can be extended to the hydrolysis and alcoholysis of all the [8]annulene complexes of the lanthanides and actinides

  19. Enhancing saccharification of cassava stems by starch hydrolysis prior to pretreatment

    OpenAIRE

    Martín, Carlos; Wei, Maogui; Xiong, Shaojun; Jönsson, Leif J.

    2017-01-01

    Chemical characterization of cassava stems from different origin revealed that glucans accounted for 54-63% of the dry weight, whereas 35-67% of these glucans consisted of starch. The cassava stems were subjected to a saccharification study including starch hydrolysis, pretreatment with either sulfuric acid or 1-ethyl-3-methylimidazolium acetate ([Emim]OAc), and enzymatic hydrolysis of cellulose. Starch hydrolysis prior to pretreatment decreased sugar degradation, improved enzymatic convertib...

  20. Apparent molar volumes and compressibilities of lanthanum, gadolinium, lutetium and sodium trifluoromethanesulfonates in N,N-dimethylformamide and N,N-dimethylacetamide

    International Nuclear Information System (INIS)

    Warmińska, Dorota; Fuchs, Anna; Lundberg, Daniel

    2013-01-01

    Highlights: ► In DMF the sequence values of both volumes and compressibilities of Ln 3+ ions are: La 3+ ≈ Gd 3+ > Lu 3+ . ► In DMA the ionic volumes of lanthanoid(III) metal ions are, within error limits, identical. ► Obtained results are the consequence of an ion–solvent bonding nature. -- Abstract: The concentration and temperature dependencies of density of lanthanum, gadolinium, lutetium and sodium trifluoromethanesulfonates in N,N-dimethylformamide (DMF) and N,N-dimethylacetamide (DMA) have been determined. From density data the apparent molar volumes and partial molar volumes of the salts at infinite dilution as well as the expansibilities have been evaluated. The apparent molar isentropic compressibilities of lanthanum, gadolinium, lutetium and sodium trifluoromethanesulfonates in DMF and DMA have been calculated from sound velocity data obtained at 298.15 K. The results have been discussed in terms of ion–solvent interactions

  1. Enhanced functional properties of tannic acid after thermal hydrolysis

    Science.gov (United States)

    Thermal hydrolysis processing of fresh tannic acid was carried out in a closed reactor at four different temperatures (65, 100, 150 and 200°C). Pressures reached in the system were 1.3 and 4.8 MPa at 150 and 200°C, respectively. Hydrolysis products (gallic acid and pyrogallol) were separated and qua...

  2. Doping and temperature dependence of incommensurate antiferromagnetism in underdoped lanthanum cuprates

    International Nuclear Information System (INIS)

    Yuan Feng; Feng Shiping; Su Zhaobin; Yu Lu

    2001-08-01

    The doping, temperature and energy dependence of the dynamical spin structure factors of the underdoped lanthanum cuprates in the normal state is studied within the t-J model using the fermion-spin transformation technique. Incommensurate peaks are found at [(1±δ)π, π], [π, (1±δ)π] at relatively low temperatures with δ linearly increasing with doping at the beginning and then saturating at higher dopings. These peaks broaden and weaken in amplitude with temperature and energy, in good agreement with experiments. The theory also predicts a rotation of these peaks by π/4 at even higher temperatures, being shifted to [(1±δ/√2)π, (1±δ/√2)π]. (author)

  3. Catalytic hydrolysis of ammonia borane via cobalt palladium nanoparticles.

    Science.gov (United States)

    Sun, Daohua; Mazumder, Vismadeb; Metin, Önder; Sun, Shouheng

    2011-08-23

    Monodisperse 8 nm CoPd nanoparticles (NPs) with controlled compositions were synthesized by the reduction of cobalt acetylacetonate and palladium bromide in the presence of oleylamine and trioctylphosphine. These NPs were active catalysts for hydrogen generation from the hydrolysis of ammonia borane (AB), and their activities were composition dependent. Among the 8 nm CoPd catalysts tested for the hydrolysis of AB, the Co(35)Pd(65) NPs exhibited the highest catalytic activity and durability. Their hydrolysis completion time and activation energy were 5.5 min and 27.5 kJ mol(-1), respectively, which were comparable to the best Pt-based catalyst reported. The catalytic performance of the CoPd/C could be further enhanced by a preannealing treatment at 300 °C under air for 15 h with the hydrolysis completion time reduced to 3.5 min. This high catalytic performance of Co(35)Pd(65) NP catalyst makes it an exciting alternative in pursuit of practical implementation of AB as a hydrogen storage material for fuel cell applications. © 2011 American Chemical Society

  4. Gastric protein hydrolysis of raw and roasted almonds in the growing pig.

    Science.gov (United States)

    Bornhorst, Gail M; Drechsler, Krista C; Montoya, Carlos A; Rutherfurd, Shane M; Moughan, Paul J; Singh, R Paul

    2016-11-15

    Gastric protein hydrolysis may influence gastric emptying rate and subsequent protein digestibility in the small intestine. This study examined the gastric hydrolysis of dietary protein from raw and roasted almonds in the growing pig as a model for the adult human. The gastric hydrolysis of almond proteins was quantified by performing tricine-sodium dodecyl sulfate-polyacrylamide gel electrophoresis and subsequent image analysis. There was an interaction between digestion time, stomach region, and almond type for gastric protein hydrolysis (palmonds (compared to roasted almonds), hypothesized to be related to structural changes in almond proteins during roasting. Greater gastric protein hydrolysis was observed in the distal stomach (compared to the proximal stomach), likely related to the lower pH in the distal stomach. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Evaluation of abalone β-glucuronidase substitution in current urine hydrolysis procedures.

    Science.gov (United States)

    Malik-Wolf, Brittany; Vorce, Shawn; Holler, Justin; Bosy, Thomas

    2014-04-01

    This study examined the potential of abalone β-glucuronidase as a viable and cost effective alternative to current hydrolysis procedures using acid, Helix pomatia β-glucuronidase and Escherichia coli β-glucuronidase. Abalone β-glucuronidase successfully hydrolyzed oxazepam-glucuronide and lorazepam-glucuronide within 5% of the spiked control concentration. Benzodiazepines present in authentic urine specimens were within 20% of the concentrations obtained with the current hydrolysis procedure using H. pomatia β-glucuronidase. JWH 018 N-(5-hydroxypentyl) β-d-glucuronide was hydrolyzed within 10% of the control concentration. Authentic urine specimens showed improved glucuronide cleavage using abalone β-glucuronidase with up to an 85% increase of drug concentration, compared with the results obtained using E. coli β-glucuronidase. The JWH 018 and JWH 073 carboxylic acid metabolites also showed increased drug concentrations of up to 24%. Abalone β-glucuronidase was able to completely hydrolyze a morphine-3-glucuronide control, but only 82% of total morphine was hydrolyzed in authentic urine specimens compared with acid hydrolysis results. Hydrolysis of codeine and hydromorphone varied between specimens, suggesting that abalone β-glucuronidase may not be as efficient in hydrolyzing the glucuronide linkages in opioid compounds compared with acid hydrolysis. Abalone β-glucuronidase demonstrates effectiveness as a low cost option for enzyme hydrolysis of benzodiazepines and synthetic cannabinoids.

  6. A meta-analysis of water quality and aquatic macrophyte responses in 18 lakes treated with lanthanum modified bentonite (PHOSLOCK®)

    NARCIS (Netherlands)

    Spears, B.M.; Mackay, E.; Yasseri, S.; Gunn, I.D.M.; Waters, K.E.; Andrews, C.; Cole, S.; Ville, de M.; Kelly, M.; Meis, S.; Moore, A.L.; Nurnberg, G.K.; Oosterhout, van Frank; Lurling, M.F.L.L.W.

    2016-01-01

    Lanthanum (La) modified bentonite is being increasingly used as a geo-engineering tool for the control of phosphorus (P) release from lake bed sediments to overlying waters. However, little is known about its effectiveness in controlling P across a wide range of lake conditions or of its potential

  7. Enteral Tube Feeding Nutritional Protein Hydrolysate Production Under Different Factors By Enzymatic Hydrolysis

    Directory of Open Access Journals (Sweden)

    Nguyen ThiQuynhHoa

    2015-01-01

    Full Text Available Abstract Hydrolysis of proteins involves the cleavage of peptide bonds to give peptides of varying sizes and amino acid composition. There are a number of types of hydrolysis enzymatic acid or alkali hydrolysis. Chemical hydrolysis is difficult to control and reduces the nutritional quality of products destroying L-form amino acids and producing toxic substances such as lysino-alanine. Enzymatic hydrolysis works without destructing amino acids and by avoiding the extreme temperatures and pH levels required for chemical hydrolysis the nutritional properties of the protein hydrolysates remain largely unaffected. In this research we investigate the fat removal and protein hydrolysis from pork meat to produce the enteral tube feeding nutritional protein hydrolysate for patient. Our results are as follows meat moisture 75.1 protein 22.6 lipid 1.71 ash 0.5 vitamin B1 1.384mg100g n hexantreatment at 80oCin 45 minutes and drying 30 minutes in 90oC.Viscosity of the hydrolysate is very low 2.240 0.092 cPand high degree of hydrolysis 31.390 0.138 . The final protein powder has balance nutritional components and acid amines low microorganisms which are safety for human consumption.

  8. Variation in band gap of lanthanum chromate by transition metals doping LaCr0.9A0.1O3 (A:Fe/Co/Ni)

    International Nuclear Information System (INIS)

    Naseem, Swaleha; Khan, Wasi; Saad, A. A.; Shoeb, M.; Ahmed, Hilal; Naqvi, A. H.; Husain, Shahid

    2014-01-01

    Transition metal (Fe, Co, Ni) doped lanthanum chromate (LaCrO 3 ) nanoparticles (NPs) were prepared by gel combustion method and calcinated at 800°C. Microstructural studies were carried by XRD and SEM/EDS techniques. The results of structural characterization show the formation of all samples in single phase without any impurity. Optical properties were studied by UV- visible and photoluminescence techniques. The energy band gap was calculated and the variation was observed with the doping of transition metal ions. Photoluminescence spectra show the emission peak maxima for the pure LaCrO 3 at about 315 nm. Influence of Fe, Co, Ni doping was studied and compared with pure lanthanum chromate nanoparticles

  9. Study of the Effect on Ionic Conductivity and Structral Morphology of the SR Doped Lanthanum Gallate Solid Electrolyte

    Science.gov (United States)

    Sood, Kapil; Singh, K.; Pandey, O. P.

    2013-07-01

    In the present study, lanthanum gallate and Sr-doped lanthanum gallate samples were prepared by conventional solid state reaction method. The phase conformation has been performed by using X-ray diffraction (XRD) study. The elemental composition has been confirmed using energy dispersive spectroscopy (EDS) analysis. Ac conductivity of the samples has been measured in the frequency range 0.1-106 Hz and from 50-800 °C. The impedance plots among real and complex impedances at particular temperature have been discussed. The behavior shows the effect of bulk and grain boundary effects of the doped sample. The impedance plots with frequency have been analyzed. The plots have been well fitted to equivalent circuit model. The conductivity shows the Arrhenius type of behavior. The activation energy has been calculated from the plots and represents that the conductivity through the material is mainly ionic. The structural morphology of the samples has been investigated using scanning electron microscope (SEM). The micrograph shows that the porosity and grain size both decreases with Sr-doping.

  10. Radiation degradation and the subsequent enzymatic hydrolysis of waste paper

    International Nuclear Information System (INIS)

    Kamakura, M.; Kaetsu, I.

    1982-01-01

    Various studies have been carried out to find methods for the pretreatment of waste cellulosic materials to make them more susceptible to enzymatic hydrolysis. In the work reported here, the effects of preirradiating waste papers on subsequent enzymatic hydrolysis have been studied

  11. Synthesis of Ni nanoparticles in lanthanum chromite ceramic matrix

    International Nuclear Information System (INIS)

    Tinti, Victor Buratto; Florio, Daniel Zanetti de; Fonseca, Fabio Coral

    2016-01-01

    Full text: Lanthanum chromite is a well-known interconnector for solid oxide fuel cells. It presents electronic conductivity at high temperatures. Moreover it is very stable in oxidizing and reducing atmospheres. Due to its high stability this material is a promising matrix to produce and stabilize nanoparticles by exothermal reaction. The objective of the present work is to synthesize and stabilize nickel nanoparticles in a stable ceramic matrix. Compounds of (La 1-x Sr x ) a (Cr 1-y Ni y )O 3 (x and y = 0, 0.1, and 0.2; a = 1, and 0.8) were synthesized by Pechini method. The powders were heat treated in air at 1300 °C and 1600°C in attempt to solubilise NiO in the matrix. Then the samples were exposed to a reducing treatment in H 2(g) flux at 900°C per 8 hours. XRD measurements were made using a D8 Focus, Bruker AXS. The data was acquired in a range of 2θ from 20° to 90°, with a step of 0,02° per second. Magnetic properties were investigated utilizing a SQUIDVSM from Quantum Design. Magnetic moment at constant magnetic field (100 Oe and 1000 Oe) was measured in a range of 2K to 300K. Analyses with variable magnetic field were performed at 2K, 196K and 390K in a rage from -5 up to 5 T. Samples were observed using TEM technique. The XRD results showed that the stoichiometric samples achieved desiderate phase. Compounds without Sr and non-stoichiometric lanthanum site showed an incomplete nickel solid solution. The addition of 10% of Sr decreases the Neel temperature from 289 K to 285K. Ni doping created a stronger effect, lowering the temperature down to 267 K , in the sample with 10% of dopant. After reduction is possible to observe peaks of Ni in the XRD, indicating that nickel was exoluted form the matrix. Images of TEM confirm the presence of nanoparticles with an approximate diameter of 3 nm. The reducing treatment increased the magnetic response. (author)

  12. High concentrations of cadmium, cerium and lanthanum in indoor air due to environmental tobacco smoke

    International Nuclear Information System (INIS)

    Böhlandt, Antje; Schierl, Rudolf; Diemer, Juergen; Koch, Christoph; Bolte, Gabriele; Kiranoglu, Mandy; Fromme, Hermann; Nowak, Dennis

    2012-01-01

    Background: Environmental tobacco smoke (ETS) is one of the most important sources for indoor air pollution and a substantial threat to human health, but data on the concentrations of the trace metals cerium (Ce) and lanthanum (La) in context with ETS exposure are scarce. Therefore the aim of our study was to quantify Ce and La concentrations in indoor air with high ETS load. Methods: In two subsequent investigations Ce, La and cadmium (Cd) in 3 smokers' (11 samples) and 7 non-smokers' (28 samples) households as well as in 28 hospitality venues in Southern Germany were analysed. Active sampling of indoor air was conducted continuously for seven days in every season in the smokers' and non-smokers' residences, and for 4 h during the main visiting hours in the hospitality venues (restaurants, pubs, and discotheques). Results: In terms of residences median levels of Cd were 0.1 ng/m 3 for non-smokers' and 0.8 ng/m 3 for smokers' households. Median concentrations of Ce were 0.4 ng/m 3 and 9.6 ng/m 3 , and median concentrations of La were 0.2 ng/m 3 and 5.9 ng/m 3 for non-smokers' and for smokers' households, respectively. In the different types of hospitality venues median levels ranged from 2.6 to 9.7 ng/m 3 for Cd, from 18.5 to 50.0 ng/m 3 for Ce and from 10.6 to 23.0 ng/m 3 for La with highest median levels in discotheques. Conclusions: The high concentrations of Ce and La found in ETS enriched indoor air of smokers' households and hospitality venues are an important finding as Ce and La are associated with adverse health effects and data on this issue are scarce. Further research on their toxicological, human and public health consequences is urgently required. - Highlights: ► We quantified cer, lanthanum and cadmium concentrations in indoor air. ► Cer and lanthanum concentrations were high in tobacco smoke enriched locations. ► Both elements can be considered as good markers for indoor air quality.

  13. Accomplishment of highly porous-lithium lanthanum titanate through microwave treatment

    Energy Technology Data Exchange (ETDEWEB)

    Lakshmi, D.; Nalini, B., E-mail: jyothsnalalin99@gmail.com [Department of Physics, Avinashilingam University for Women, Coimbatore, Tamilnadu (India); Abhilash, K. P.; Selvin, P. Christopher [Department of Physics, NGM college for arts and science, Pollachi, Tamilnadu (India)

    2016-05-23

    Perovskite structured (ABO{sub 3}) lithium lanthanum titanate (LLTO) is a successful electrolyte reported by several scientists in the recent past. It is believed that intercalation and de-intercalation of Li ions inside solid electrolyte can be improved by increasing the porosity of the material. Hence in this research work, an attempt is made to increase the porosity of the LLTO electrolyte by rapid-microwave synthesis route. The microwave prepared LLTO is compared with the sol-gel synthesized LLTO. The prepared samples are analyzed with XRD, SEM, PL and cyclic Voltammetry studies. Morphological analysis proves that microwave synthesized LLTO contains much pores compared to the Sol-gel LLTO. A remarkable difference in its electrochemical property is also demonstrated and analysed with cyclic voltammetric studies and the results are presented.

  14. Effect of Acid Hydrolysis and Thermal Hydrolysis on Solubility and Properties of Oil Palm Empty Fruit Bunch Fiber Cellulose Hydrogel

    Directory of Open Access Journals (Sweden)

    Sinyee Gan

    2015-11-01

    Full Text Available Cellulose hydrogel was produced from pretreated oil palm empty fruit bunch fiber (EFB that went through acid hydrolysis and thermal hydrolysis. The pretreated EFB was dissolved in LiOH/urea aqueous solution using the rapid dissolution method and was subjected to a crosslinking process with the aid of epichlorohydrin to form hydrogel. The effects of both hydrolyses’ time on average molecular weight (Mŋ, solubility, and properties of EFB hydrogels were evaluated. Both hydrolyses led to lower Mŋ, lower crystallinity index (CrI and hence, resulted in higher cellulose solubility. X-ray diffraction (XRD characterization revealed the CrI and transition of crystalline structure of EFB from cellulose I to II. The effects of hydrolysis time on the transparency, degree of swelling (DS, and morphology of the regenerated cellulose hydrogel were also investigated using an ultraviolet-visible (UV-Vis spectrophotometer and a Field emission scanning electron microscope (FESEM, respectively. These findings provide an efficient method to improve the solubility and properties of regenerated cellulose products.

  15. Enzymatic Hydrolysis of Alkaline Pretreated Coconut Coir

    Directory of Open Access Journals (Sweden)

    Akbarningrum Fatmawati

    2013-06-01

    Full Text Available The purpose of this research is to study the effect of concentration and temperature on the cellulose and lignin content, and the reducing sugars produced in the enzymatic hydrolysis of coconut coir. In this research, the coconut coir is pretreated using 3%, 7%, and 11% NaOH solution at 60oC, 80oC, and 100oC. The pretreated coir were assayed by measuring the amount of cellulose and lignin and then hydrolysed using Celluclast and Novozyme 188 under various temperature (30oC, 40oC, 50oC and pH (3, 4, 5. The hydrolysis results were assayed for the reducing sugar content. The results showed that the alkaline delignification was effective to reduce lignin and to increase the cellulose content of the coir. The best delignification condition was observed at 11% NaOH solution and 100oC which removed 14,53% of lignin and increased the cellulose content up to 50,23%. The best condition of the enzymatic hydrolysis was obtained at 50oC and pH 4 which produced 7,57 gr/L reducing sugar. © 2013 BCREC UNDIP. All rights reservedReceived: 2nd October 2012; Revised: 31st January 2013; Accepted: 6th February 2013[How to Cite: Fatmawati, A., Agustriyanto, R., Liasari, Y. (2013. Enzymatic Hydrolysis of Alkaline Pre-treated Coconut Coir. Bulletin of Chemical Reaction Engineering & Catalysis, 8 (1: 34-39 (doi:10.9767/bcrec.8.1.4048.34-39[Permalink/DOI: http://dx.doi.org/10.9767/bcrec.8.1.4048.34-39] | View in  |

  16. Vaporization study on lanthanum-neodymium alloys by mass-spectrometry

    International Nuclear Information System (INIS)

    Shoji, Y.; Matsui, T.

    1999-01-01

    Partial vapor pressure of Nd(g) over La x Nd 1-x alloys (x = 0.10, 0.20, 0.30, 0.40, 0.50, 0.60, 0.70, 0.80 and 0.90) was measured with a time-of-flight mass-spectrometer equipped with a tungsten Knudsen cell over the temperature range of 1474-1767 K. Thermodynamic activity of neodymium in the liquid alloys was determined by comparing the partial vapor pressure of Nd(g) over the alloys with that over the pure metal. The thermodynamic activity of lanthanum in the alloys was calculated from that of neodymium obtained experimentally in this study by graphic integration using the Gibbs-Duhem equation. Both activities for each element, thus obtained, showed positive deviations from Raoult's law over the entire compositional range. Thermodynamic quantities such as Gibbs free energy of formation, excess enthalpy etc. were also calculated from the thermodynamic activities. (orig.)

  17. Ethanol Electrooxidation on Pt with Lanthanum Oxide as Cocatalyst in a DAFC

    Directory of Open Access Journals (Sweden)

    T. A. B. Santoro

    2012-01-01

    Full Text Available Electrocatalytic activity toward ethanol electrooxidation of Pt particles in PtLa/C catalysts with different Pt : La ratios has been studied with different electrochemical and spectroscopic techniques, and the results were compared to those of Pt/C catalyst. Significant enhancement in the electrocatalytic activity has been achieved by depositing the Pt particles with lanthanum oxides/hydroxides using an alcohol reduction method. Compared to Pt/C catalyst, PtLa/C materials exhibit a lower onset potential and a higher electron-transfer rate constant for the investigated reaction. These studies illustrate the possibility of utilizing Pt/C with La oxides/hidroxides as electrocatalyst for direct alcohol fuel cells (DAFCs.

  18. Radiation degration and the subsequent enzymatic hydrolysis of waste papers

    International Nuclear Information System (INIS)

    Kamakura, M.; Kaetsu, I.

    1982-01-01

    In recent years, many methods have been proposed for the hydrolysis of waste cellulose to utilize it as a new source of alcohol. Because it is difficult to hydrolyze waste cellulosic materials effectivley with an enzyme, the effects of preirradiating waste papers on subsequent enzymatic hydrolysis was studied. Preirradiation (x rays from 60 Co) accelerated the hydrolysis rate of newspaper by cellulase and the reducing-sugar yield increased with increasing irradiation dose. It is thought that preirradiation probably contributes to loosening and releasing the compactly entangled structure of cellulose and lignin in the materials by radiation degradation

  19. Lanthanide based conversion coatings for long term wet storage of aluminium-clad spent fuel

    International Nuclear Information System (INIS)

    Fernandes, S.M.C.; Correa, O.V.; De Souza, J.A.; Ramanathan, L.V.

    2010-01-01

    Spent fuels from research reactors are stored in basins with water of less than desirable quality at many facilities around the world and instances of cladding failure caused by pitting corrosion have been reported. Conversion coatings have been used in many industries to protect different metals, including aluminium alloys. This paper presents the results of an ongoing investigation in which the corrosion resistance of lanthanide (cerium, lanthanum and praseodymium) based conversion coated RR fuel cladding alloys has been studied. Electrochemical tests in the laboratory revealed higher corrosion resistance of CeO 2 , La 2 O 3 and Pr 2 O 3 coated AA 1100 and AA 6061 alloys in NaCl solutions. Uncoated and CeO 2 coated coupons of these alloys exposed for 50 days to the spent fuel basin of the IEA-R1 research reactor in IPEN, Brazil, revealed marked reductions in the extent of pitting corrosion. (author)

  20. Thermoluminescent response of LaAlO{sub 3}:Pr; Respuesta termoluminiscente de LaAlO{sub 3}:Pr

    Energy Technology Data Exchange (ETDEWEB)

    Morales H, A.; Zarate M, J. [Universidad Michoacana de San Nicolas de Hidalgo, Instituto de Investigacion en Metalurgia y Materiales, Ciudad Universitaria, Edif. U, 58060 Morelia, Michoacan (Mexico); Azorin N, J. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (Mexico); Rivera M, T., E-mail: feyo_yo@hotmail.com [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria 694, 11500 Mexico D. F. (Mexico)

    2015-10-15

    In this study, the thermoluminescence response of doped lanthanum aluminate (LaAlO{sub 3}) with praseodymium ion (Pr) obtained by the Pechini method and drying by the spraying technique Spry Dryer was studied. The obtained powders were analyzed structurally by the X-ray diffraction technique; the morphological characterization was by the scanning electron microscopy technique. The obtained powders at 800 degrees C presented crystallinity and showed a Rhombohedral crystal structure, this phase was observed by X-ray diffraction patterns. Thermoluminescence response of LaAlO{sub 3}:Pr showed a brightness curve with a peak centered at 157 degrees C. The sensitivity of the doped samples was improved about 90 times in comparison with the undoped sample. Thermoluminescence response in function of the wavelength showed a maximum at 230 nm, reproducibility of thermoluminescence response was ±50%. Also the fading in thermoluminescence response was studied. (Author)

  1. Thermoluminescent response of LaAlO3:Pr

    International Nuclear Information System (INIS)

    Morales H, A.; Zarate M, J.; Azorin N, J.; Rivera M, T.

    2015-10-01

    In this study, the thermoluminescence response of doped lanthanum aluminate (LaAlO 3 ) with praseodymium ion (Pr) obtained by the Pechini method and drying by the spraying technique Spry Dryer was studied. The obtained powders were analyzed structurally by the X-ray diffraction technique; the morphological characterization was by the scanning electron microscopy technique. The obtained powders at 800 degrees C presented crystallinity and showed a Rhombohedral crystal structure, this phase was observed by X-ray diffraction patterns. Thermoluminescence response of LaAlO 3 :Pr showed a brightness curve with a peak centered at 157 degrees C. The sensitivity of the doped samples was improved about 90 times in comparison with the undoped sample. Thermoluminescence response in function of the wavelength showed a maximum at 230 nm, reproducibility of thermoluminescence response was ±50%. Also the fading in thermoluminescence response was studied. (Author)

  2. Bioethanol production: Pretreatment and enzymatic hydrolysis of softwood

    Energy Technology Data Exchange (ETDEWEB)

    Tengborg, Charlotte

    2000-05-01

    The enzymatic hydrolysis process can be used to produce bioethanol from softwood, which are the dominating raw material in the Northern hemisphere. This thesis deals with the development of the process focusing on the pretreatment and the enzymatic hydrolysis stages. The influence of pretreatment conditions on sugar yield, and the effect of inhibitors on the ethanol yield, were investigated for spruce and pine. The maximum yields of hemicellulose sugars and glucose were obtained under different pretreatment conditions. This indicates that two-stage pretreatment may be preferable. The added catalysts, H{sub 2}SO{sub 4} and SO{sub 2}, resulted in similar total sugar yields about 40 g/100 g dry raw material. However, the fermentability of SO{sub 2}-impregnated material was better. This pretreatment resulted in the formation of inhibitors to the subsequent process steps, e.g. sugar and lignin degradation products. The glucose yield in the enzymatic hydrolysis stage was affected by various parameters such as enzyme loading, temperature, pH, residence time, substrate concentration, and agitation. To decrease the amount of fresh water used and thereby waste water produced, the sugar-rich prehydrolysate from the pretreatment step was included in the enzymatic hydrolysis of the solid fraction, resulting in a reduction in the cellulose conversion of up to 36%. Different prehydrolysate detoxification methods, such as treatment with Ca(OH){sub 2}, laccase, and fermentation using yeast, were investigated. The latter was shown to be very efficient. The amount of fresh water used can be further reduced by recycling various process streams. This was simulated experimentally in a bench-scale process. A reduction in fresh water demand of 50% was obtained without any further negative effects on either hydrolysis or fermentation.

  3. Modeling the mechanisms of biological GTP hydrolysis

    DEFF Research Database (Denmark)

    Carvalho, Alexandra T.P.; Szeler, Klaudia; Vavitsas, Konstantinos

    2015-01-01

    Enzymes that hydrolyze GTP are currently in the spotlight, due to their molecular switch mechanism that controls many cellular processes. One of the best-known classes of these enzymes are small GTPases such as members of the Ras superfamily, which catalyze the hydrolysis of the γ-phosphate bond...... in GTP. In addition, the availability of an increasing number of crystal structures of translational GTPases such as EF-Tu and EF-G have made it possible to probe the molecular details of GTP hydrolysis on the ribosome. However, despite a wealth of biochemical, structural and computational data, the way...

  4. Optical and photoemission studies of lanthanum hydrides

    International Nuclear Information System (INIS)

    Peterman, D.J.; Peterson, D.T.; Weaver, J.H.

    1980-01-01

    The results of optical absorptivity and photoemission measurements on lanthanum hydrides, LaH/sub x/ (1.98 less than or equal to x less than or equal to 2.89) are reported. The low energy (hν less than or equal to 0.5 eV) optical features in LaH/sub x/ are attributed to the filling of octahedral sites. Higher energy interband absorption involves states within the d-band complex, analogous to other dihydrides. As x increases above 2.0, the optical features change rapidly due to the increase in the number of occupied octahedral sites. Various band structure studies suggest that LaH 3 might be a semiconductor. Photoemission results show that as x increases, the d-derived states at E/sub F/ are drawn down and that for LaH 2 89 only very weak valence band emission is observed. The hydrogen-derived bonding bands are shown centered approx. 5 eV below E/sub F/. Observed chemical shifts in the La 5p/sub 1/2 3/2/ cores are discussed for 1.98 less than or equal to x less than or equal to 2.89

  5. Water Availability as a Measure of Cellulose Hydrolysis Efficiency

    DEFF Research Database (Denmark)

    Hsieh, Chia-Wen

    of sugars, salts, and surfactants impact the water relaxation time. Systems with high concentrations of sugars and salts tend to have low water availability, as these form strong interactions with water to keep their solubility, leaving less water available for hydrolysis. Thus, cellulase performance...... decreases. However, the addition of surfactants such as polyethylene glycol (PEG) increases the water mobility, leading to higher water availability, and ultimately higher glucose production. More specifically, the higher water availability boosts the activity of processive cellulases. Thus, water...... availability is vital for efficient hydrolysis, especially at high dry matter content where water availability is low. At high dry matter content, cellulase activity changes water interactions with biomass, affecting the water mobility. While swelling and fiber loosening also take place during hydrolysis...

  6. Enzymatic hydrolysis of biomass at high-solids loadings – A review

    International Nuclear Information System (INIS)

    Modenbach, Alicia A.; Nokes, Sue E.

    2013-01-01

    Enzymatic hydrolysis is the unit operation in the lignocellulose conversion process that utilizes enzymes to depolymerize lignocellulosic biomass. The saccharide components released are the feedstock for fermentation. When performed at high-solids loadings (≥15% solids, w/w), enzymatic hydrolysis potentially offers many advantages over conversions performed at low- or moderate-solids loadings, including increased sugar and ethanol concentrations and decreased capital and operating costs. The goal of this review is to provide a consolidated source of information on studies using high-solids loadings in enzymatic hydrolysis. Included in this review is a brief discussion of the limitations, such as a lack of available water, difficulty with mixing and handling, insufficient mass and heat transfer, and increased concentration of inhibitors, associated with the use of high solids, as well as descriptions and findings of studies that performed enzymatic hydrolysis at high-solids loadings. Reactors designed and/or equipped for improved handling of high-solids slurries are also discussed. Lastly, this review includes a brief discussion of some of the operations that have successfully scaled-up and implemented high-solids enzymatic hydrolysis at pilot- and demonstration-scale facilities. -- Highlights: •High solids enzymatic hydrolysis needed for conversion process to be cost-effective. •Limitations must be addressed before benefits of high-solid loadings fully realized. •Some success with high-solids loadings at pilot and demonstration scale

  7. Reaction rate of hydrolysis of iodine

    International Nuclear Information System (INIS)

    Miyake, Yoshikazu; Eguchi, Wataru; Adachi, Motonari

    1979-01-01

    Absorption rates of dilute iodine vapor contained in air by aqueous mixtures of sodium hydroxide and boric acid were measured using a laminar liquid jet column absorber at 298 K. Absorption rates in this system are controlled by a series of complex reactions taking place in the liquid phase. The reaction rate constant of iodine hydrolysis in the aqueous phase was determined from the absorption rates observed under the conditions that the base-catalytic hydrolysis reaction of iodine can be considered to be irreversible and that other reactions can be neglected. The absorption rates calculated theoretically with the rate constant value obtained above were in good accordance with the whole experimental data observed for a wide range of experimental conditions. (author)

  8. Photoluminescence, reddish orange long persistent luminescence and photostimulated luminescence properties of praseodymium doped CdGeO3 phosphor

    International Nuclear Information System (INIS)

    Jin, Yahong; Hu, Yihua; Chen, Li; Fu, Yinrong; Mu, Zhongfei; Wang, Tao; Lin, Jun

    2014-01-01

    Highlights: • A novel phosphor CdGeO 3 :Pr 3+ was synthesized successfully. • The persistent luminescence properties of CdGeO 3 :Pr 3+ were studied. • The photostimulated luminescence properties of CdGeO 3 :Pr 3+ were investigated. • The persistent and photostimulated luminescence mechanisms were discussed in detail. - Abstract: Praseodymium doped CdGeO 3 phosphors were prepared successfully by a conventional high temperature solid-state reaction method. It showed reddish orange long persistent luminescence (LPL) after the short UV-irradiation. The reddish orange photostimulated luminescence (PSL) was also observed upon near infrared stimulation at 980 nm after per-exposure into UV light. The origin of LPL and PSL was identified with the emission from Pr 3+ ions with the aid of traps in host lattice. The optimal concentration of Pr 3+ ions for the brightest photoluminescence (PL) emission and the best LPL characteristic were experimentally to be about 3% and 0.5 mol%, respectively. The trapping and de-trapping processes of charge carriers between shallower and deep traps were illustrated. A model was proposed on the basis of experimental results to study the mechanisms of LPL and PSL

  9. Study on the Hydrolysis Kinetics of Xylan on Different Acid Catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Na, Byeong-Il; Lee, Jae-Won [Chonnam National University, Gwangju (Korea, Republic of)

    2014-04-15

    In this study, we investigated kinetic model for the acid-catalyzed xylan hydrolysis at temperature 120-150 .deg. C. Also, we analyzed the kinetic parameters for xylose production and furfural decomposition. The hydrolysis of xylan and the degradation of xylose were promoted by high reaction temperature and acid concentration. The optimal hydrolysis condition for the highest reaction rate constants (k{sub 1}) was different depending on the acid catalysts. Among sulfuric, oxalic and maleic acid, the xylan reaction rate constants (k{sub 1}) to xylose had the highest value of 0.0241 min{sup -1} when 100 mM sulfuric acid was used at 120 .deg. C. However, sulfuric acid induced more xylose degradation compared to oxalic and maleic acid hydrolysis. The activation energy for xylan degradation was the highest when sulfuric acid was used.

  10. Evaluation of physical structural features on influencing enzymatic hydrolysis efficiency of micronized wood

    Science.gov (United States)

    Jinxue Jiang; Jinwu Wang; Xiao Zhang; Michael Wolcott

    2016-01-01

    Enzymatic hydrolysis of lignocellulosic biomass is highly dependent on the changes in structural features after pretreatment. Mechanical milling pretreatment is an effective approach to alter the physical structure of biomass and thus improve enzymatic hydrolysis. This study examined the influence of structural characteristics on the enzymatic hydrolysis of micronized...

  11. Accelerated anaerobic hydrolysis rates under a combination of intermittent aeration and anaerobic conditions

    DEFF Research Database (Denmark)

    Jensen, T. R.; Lastra Milone, T.; Petersen, G.

    2017-01-01

    Anaerobic hydrolysis in activated return sludge was investigated in laboratory scale experiments to find if intermittent aeration would accelerate anaerobic hydrolysis rates compared to anaerobic hydrolysis rates under strict anaerobic conditions. The intermittent reactors were set up in a 240 h...... for calculating hydrolysis rates based on soluble COD were compared. Two-way ANOVA with the Bonferroni post-test was performed in order to register any significant difference between reactors with intermittent aeration and strictly anaerobic conditions respectively. The experiment demonstrated a statistically...... significant difference in favor of the reactors with intermittent aeration showing a tendency towards accelerated anaerobic hydrolysis rates due to application of intermittent aeration. The conclusion of the work is thus that intermittent aeration applied in the activated return sludge process (ARP) can...

  12. Size effects of polycrystalline lanthanum modified Bi4Ti3O12 thin films

    International Nuclear Information System (INIS)

    Simoes, A.Z.; Riccardi, C.S.; Cavalcante, L.S.; Gonzalez, A.H.M.; Longo, E.; Varela, J.A.

    2008-01-01

    The film thickness dependence on the ferroelectric properties of lanthanum modified bismuth titanate Bi 3.25 La 0.75 Ti 3 O 12 was investigated. Films with thicknesses ranging from 230 to 404 nm were grown on platinum-coated silicon substrates by the polymeric precursor method. The internal strain is strongly influenced by the film thickness. The morphology of the film changes as the number of layers increases indicating a thickness dependent grain size. The leakage current, remanent polarization and drive voltage were also affected by the film thickness

  13. Thermopressure hydrolysis. Paper; Thermodruckhydrolyse. Paper

    Energy Technology Data Exchange (ETDEWEB)

    Stahl, R. [Scheuchl GmbH, Ortenburg (Germany); Prechtl, S. [Applikations- und Technikzentrum fuer Energieverfahrens-, Umwelt- und Stroemungstechnik (ATZ-EVUS), Sulzbach-Rosenberg (Germany)

    2000-12-01

    This paper presents a processing method which consists in thermal hydrolysis and subsequent anaerobic fermentation and is especially well suited for wet, low-structure organic wastes. [German] Das vorgestellte Verwertungsverfahren bestehend aus thermischer Hydrolyse und anschliessender anaerober Vergaerung eignet sich besonders fuer nasse, strukturarme organische Abfaelle. (orig.)

  14. The lanthanum(III molybdate(VI La4Mo7O27

    Directory of Open Access Journals (Sweden)

    Petra Becker

    2009-08-01

    Full Text Available Crystals of the orthorhombic phase La4Mo7O27 (lanthanum molybdenum oxide were obtained from a non-stoichiometric melt in the pseudo-ternary system La2O3–MoO3–B2O3. In the crystal structure, distorted square-antiprismatic [LaO8] and monocapped square-antiprismatic [LaO9] polyhedra are connected via common edges and faces into chains along [010]. These chains are arranged in layers that alternate with layers of [MoO4] and [MoO5] polyhedra parallel to (001. In the molybdate layers, a distorted [MoO5] trigonal bipyramid is axially connected to two [MoO4] tetrahedra, forming a [Mo3O11] unit.

  15. Hydrolysis of biomass material

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Andrew J.; Orth, Rick J.; Franz, James A.; Alnajjar, Mikhail

    2004-02-17

    A method for selective hydrolysis of the hemicellulose component of a biomass material. The selective hydrolysis produces water-soluble small molecules, particularly monosaccharides. One embodiment includes solubilizing at least a portion of the hemicellulose and subsequently hydrolyzing the solubilized hemicellulose to produce at least one monosaccharide. A second embodiment includes solubilizing at least a portion of the hemicellulose and subsequently enzymatically hydrolyzing the solubilized hemicellulose to produce at least one monosaccharide. A third embodiment includes solubilizing at least a portion of the hemicellulose by heating the biomass material to greater than 110.degree. C. resulting in an aqueous portion that includes the solubilized hemicellulose and a water insoluble solids portion and subsequently separating the aqueous portion from the water insoluble solids portion. A fourth embodiment is a method for making a composition that includes cellulose, at least one protein and less than about 30 weight % hemicellulose, the method including solubilizing at least a portion of hemicellulose present in a biomass material that also includes cellulose and at least one protein and subsequently separating the solubilized hemicellulose from the cellulose and at least one protein.

  16. Evaluation and comparison of two complexometric titration methods for determining of lanthanum in cloridric solutions

    International Nuclear Information System (INIS)

    Menezes, M.F.; Santos, R.L.C. dos; Goes, M.A.C. de

    1994-01-01

    The fast determination of total rare earth concentration in aqueous solutions is based on titrimetric methods using EDTA as complexing agent. This paper evaluates two among several others titrimetric methods used in the determination of lanthanum in hydrochloric acid solutions, using xylenol orange and a mixture of methyl orange and xylenol orange as indicators. The applied statistical evaluation allowed the determination of the stability, accuracy and adequacy of these methods on a given technical specification. (author). 12 refs., 03 tabs., 01 fig

  17. Effects of acid hydrolysis intensity on the properties of starch/xanthan mixtures.

    Science.gov (United States)

    Jiang, Min; Hong, Yan; Gu, Zhengbiao; Cheng, Li; Li, Zhaofeng; Li, Caiming

    2018-01-01

    The effects of acid hydrolysis intensity on the physicochemical properties of starch/xanthan gum (XG) system were studied. Waxy corn starch (WCS) was subjected to different concentrations of hydrochloric acid, and crystallization and relative molecular weight analysis were performed. The results revealed that the starch granules became smaller during acid hydrolysis. X-ray diffraction pattern analysis showed that the crystal structure did not change with acid hydrolysis. Evaluation of the properties and digestibility of different acid-thinned starch/XG systems indicated that the viscosity of acid-thinned starch/XG decreased with increased acid hydrolysis intensity. Rheological property measurements indicated that the compound systems were a pseudo-plastic fluid, which is a typical weak gel structure. Finally, we show that the WCS1.0M/XG has the highest stability of the tested mixtures. We conclude that adjusting the conditions of acid hydrolysis improves the stability and food quality-enhancing properties of starch. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Secondary deuterium isotope effects in the hydrolysis of some acetals

    International Nuclear Information System (INIS)

    Paterson, R.V.

    Secondary α-deuterium kinetic isotope effects have been determined in the hydrolyses of some acetals. Benzaldehyde dimethyl acetal and 2-phenyl-1,3-dioxolan show isotope effects in agreement with an A1 mechanism. 2-Phenyl-4,4,5,5-tetramethyl-1,3-dioxolan, which has been shown to undergo hydrolysis by an A2 type mechanism, has an isotope effect in agreement with participation by water in the transition state. Hydrolysis of benzylidene norbornanediols, although complicated by isomerisation, has an isotope effect in agreement with an A2 mechanism. Kinetic isotope effects in acetals which have a neighbouring carboxyl group have also been determined. Hydrolysis of 2-carboxybenzaldehyde dimethyl acetal in aqueous and 82% w/w dioxan-water buffers has isotope effects in agreement with a large degree of carbonium ion character in the transition state. Anderson and Capon proposed nucleophilic participation in the hydrolysis of this acetal in 82% dioxan-water. The isotope effect determined in this study is not in agreement with this finding. Hydrolysis of 2-(2'-carboxyphenyl)-4,4,5,5-tetramethyl-1,3-dioxolan shows an isotope effect larger than the corresponding dioxolan without the carboxyl group in agreement with some carbonium ion character in the transition state. A new synthesis of a deuterated aldehyde is described which might be general for aldehydes which will not form benzoins readily. (author)

  19. Recycle of enzymes and substrate following enzymatic hydrolysis of steam-pretreated aspenwood

    Energy Technology Data Exchange (ETDEWEB)

    Mes-Hartree, M.; Hogan, C.M.; Saddler, J.N.

    1987-09-01

    The commercial production of chemicals and fuels from lignocellulosic residues by enzymatic means still requires considerable research on both the technical and economic aspects. Two technical problems that have been identified as requiring further research are the recycle of the enzymes used in hydrolysis and the reuse of the recalcitrant cellulose remaining after incomplete hydrolysis. Enzyme recycle is required to lower the cost of the enzymes, while the reuse of the spent cellulose will lower the feedstock cost. The conversion process studied was a combined enzymatic hydrolysis and fermentation (CHF) procedure that utilized the cellulolytic enzymes derived from the fungus Trichoderma harzianum E58 and the yeast Saccharomyces cerevisiae. The rate and extent of hydrolysis and ethanol production was monitored as was the activity and hydrolytic potential of the enzymes remaining in the filtrate after the hydrolysis period. When a commercial cellulose was used as the substrate for a routine 2-day CHF process, 60% of the original filter paper activity could be recovered. When steam-treated, water-extracted aspenwood was used as the substrate, only 13% of the original filter paper activity was detected after a similar procedure. The combination of 60% spent enzymes with 40% fresh enzymes resulted in the production of 30% less reducing sugars than the original enzyme mixture. Since 100% hydrolysis of the cellulose portion is seldom accomplished in an enzymatic hydrolysis process, the residual cellulose was used as a substrate for the growth of T. harzianum E58 and production of cellulolytic enzymes. The residue remaining after the CHF process was used as a substrate for the production of the cellulolytic enzymes. The production of enzymes from the residue of the Solka Floc hydrolysis was greater than the production of enzymes from the original Solka Floc. (Refs. 14).

  20. Dynamic Modeling of Indole Glucosinolate Hydrolysis and Its Impact on Auxin Signaling

    Directory of Open Access Journals (Sweden)

    Daniel Vik

    2018-04-01

    Full Text Available Plants release chemicals to deter attackers. Arabidopsis thaliana relies on multiple defense compounds, including indol-3-ylmethyl glucosinolate (I3G, which upon hydrolysis initiated by myrosinase enzymes releases a multitude of bioactive compounds, among others, indole-3-acetonitrile and indole-3-acetoisothiocyanate. The highly unstable isothiocyanate rapidly reacts with other molecules. One of the products, indole-3-carbinol, was reported to inhibit auxin signaling through binding to the TIR1 auxin receptor. On the contrary, the nitrile product of I3G hydrolysis can be converted by nitrilase enzymes to form the primary auxin molecule, indole-3-acetic acid, which activates TIR1. This suggests that auxin signaling is subject to both antagonistic and protagonistic effects of I3G hydrolysis upon attack. We hypothesize that I3G hydrolysis and auxin signaling form an incoherent feedforward loop and we build a mathematical model to examine the regulatory network dynamics. We use molecular docking to investigate the possible antagonistic properties of different I3G hydrolysis products by competitive binding to the TIR1 receptor. Our simulations reveal an uncoupling of auxin concentration and signaling, and we determine that enzyme activity and antagonist binding affinity are key parameters for this uncoupling. The molecular docking predicts that several I3G hydrolysis products strongly antagonize auxin signaling. By comparing a tissue disrupting attack – e.g., by chewing insects or necrotrophic pathogens that causes rapid release of I3G hydrolysis products – to sustained cell-autonomous I3G hydrolysis, e.g., upon infection by biotrophic pathogens, we find that each scenario gives rise to distinct auxin signaling dynamics. This suggests that plants have different defense versus growth strategies depending on the nature of the attack.

  1. Combined wet oxidation and alkaline hydrolysis of polyvinylchloride

    DEFF Research Database (Denmark)

    Sørensen, E.; Bjerre, A.B.

    1992-01-01

    In view of the widespread aversion to burning polyvinylchloride (PVC) together with municipal waste, we have attempted an alternative approach to its decomposition. This paper describes a combined wet oxidation/alkaline hydrolysis yielding water soluble, biodegradable products. Experiments were...... carried out at temperatures from 180-260 degree C and reaction times of 8-24 min. The chloride liberated provides information on the rate constants. Considering the measured Cl- and Chemical Oxygen Demand (COD) values, we find hydrolysis and oxidation processes to be interdependent. The main products...

  2. Optimization of enzymatic hydrolysis of guar gum using response surface methodology.

    Science.gov (United States)

    Mudgil, Deepak; Barak, Sheweta; Khatkar, B S

    2014-08-01

    Guar gum is a polysaccharide obtained from guar seed endosperm portion. Enzymatically hydrolyzed guar gum is low in viscosity and has several health benefits as dietary fiber. In this study, response surface methodology was used to determine the optimum conditions for hydrolysis that give minimum viscosity of guar gum. Central composite was employed to investigate the effects of pH (3-7), temperature (20-60 °C), reaction time (1-5 h) and cellulase concentration (0.25-1.25 mg/g) on viscosity during enzymatic hydrolysis of guar (Cyamopsis tetragonolobus) gum. A second order polynomial model was developed for viscosity using regression analysis. Results revealed statistical significance of model as evidenced from high value of coefficient of determination (R(2) = 0.9472) and P < 0.05. Viscosity was primarily affected by cellulase concentration, pH and hydrolysis time. Maximum viscosity reduction was obtained when pH, temperature, hydrolysis time and cellulase concentration were 6, 50 °C, 4 h and 1.00 mg/g, respectively. The study is important in optimizing the enzymatic process for hydrolysis of guar gum as potential source of soluble dietary fiber for human health benefits.

  3. Antioxidative activities of hydrolysates from edible birds nest using enzymatic hydrolysis

    Science.gov (United States)

    Muhammad, Nurul Nadia; Babji, Abdul Salam; Ayub, Mohd Khan

    2015-09-01

    Edible bird's nest protein hydrolysates (EBN) were prepared via enzymatic hydrolysis to investigate its antioxidant activity. Two types of enzyme (alcalase and papain) were used in this study and EBN had been hydrolysed with different hydrolysis time (30, 60, 90 and 120 min). Antioxidant activities in EBN protein hydrolysate were measured using DPPH, ABTS+ and Reducing Power Assay. From this study, increased hydrolysis time from 30 min to 120 min contributed to higher DH, as shown by alcalase (40.59%) and papain (24.94%). For antioxidant assay, EBN hydrolysed with papain showed higher scavenging activity and reducing power ability compared to alcalase. The highest antioxidant activity for papain was at 120 min hydrolysis time with ABTS (54.245%), DPPH (49.78%) and Reducing Power (0.0680). Meanwhile for alcalase, the highest antioxidant activity was at 30 min hydrolysis time. Even though scavenging activity for EBN protein hydrolysates were high, the reducing power ability was quite low as compared to BHT and ascorbic Acid. This study showed that EBN protein hydrolysate with alcalase and papain treatments potentially exhibit high antioxidant activity which have not been reported before.

  4. The kinetics of hydrolysis of acetylsalicylic acid (Aspirin) in different ...

    African Journals Online (AJOL)

    The kinetics of hydrolysis of Acetylsalicylic acid (Aspirin) to salicylic acid was followed by the direct spectrophotometric measurement of the amount of salicylic acid produced with time. Salicylic acid was complexed with ferric ion giving a characteristic purple colour (λlm 523nm). The kinetics of hydrolysis was found to follow ...

  5. Low frequency ultrasonic-assisted hydrolysis of starch in the presence of α-amylase.

    Science.gov (United States)

    Gaquere-Parker, Anne; Taylor, Tamera; Hutson, Raihannah; Rizzo, Ashley; Folds, Aubrey; Crittenden, Shastina; Zahoor, Neelam; Hussein, Bilal; Arruda, Aaron

    2018-03-01

    Hydrolysis of starch is an important process in the food industry and in the production of bioethanol or smaller carbohydrate molecules that can be used as starting blocks for chemical synthesis. Such hydrolysis can be enhanced by lowering the pH, heating the reaction mixture or catalyzing the reaction with enzymes. This study reports the effect of sonication on the reaction rate of starch hydrolysis at different temperatures, in the presence or absence of alpha-amylase. Starch Azure, a commercially available potato starch covalently linked with Remazol Brilliant Blue, has been chosen since its hydrolysis releases a blue dye, which concentration can be monitored by UV Vis spectroscopy. Ultrasounds, regardless of experimental conditions, provide the highest reaction rate for such hydrolysis. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Sintering and electrical properties of strontium-doped lanthanum manganite

    Energy Technology Data Exchange (ETDEWEB)

    Tarrago, Diego Pereira; Sousa, Vania Caldas de [Universidade Federal do Rio Grande do Sul (LABIOMAT/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas, Metalurgica e de Materiais. Lab. de Biomateriais], Email: dptarrago@gmail.com; Moreno Buriel, Berta; Chinarro Martini, Eva; Jurado Egea, Jose Ramon [Consejo Superior de Investigaciones Cientificas (ICV/CSIC), Madrid (Spain). Inst. de Ceramica y Vidrio; Malfatti, Celia de Fraga [Universidade Federal do Rio Grande do Sul (LAPEC/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas, Metalurgica e de Materiais. Lab. de Pesquisa em Corrosao

    2010-07-01

    Lanthanum strontium manganites (LSM) are potential materials for cathode applications in solid oxide fuel cells (SOFC) due to their good catalytic activity, chemical stability and compatibility with electrolyte materials in high temperatures. The sinterability of single phase La{sub 1-x}Sr{sub x}Mn{sub O3} (x=0.18) perovskite powders and the electrical properties of the resulting samples are analyzed in this study. Using a heating microscope, the powders were pressed and sintered at different pressures and temperatures, resulting in an open porosity of 33.36% when compacted at 125 MPa and sintered at 1200 degree C. Top and cross-section s canning electron microscopy (SEM) micrographs revealed interconnected pores in the sintered body and, hence, a suitable microstructure for the application. The activation energy for conductance was 0.04 eV and the tested LSM bulk started to exhibit adequate electrical properties at about 500 degree C. (author)

  7. Deciphering Intrinsic Inter-subunit Couplings that Lead to Sequential Hydrolysis of F 1 -ATPase Ring

    Science.gov (United States)

    Dai, Liqiang; Flechsig, Holger; Yu, Jin

    2017-10-01

    The rotary sequential hydrolysis of metabolic machine F1-ATPase is a prominent feature to reveal high coordination among multiple chemical sites on the stator F1 ring, which also contributes to tight coupling between the chemical reaction and central {\\gamma}-shaft rotation. High-speed AFM experiments discovered that the sequential hydrolysis was maintained on the F1 ring even in the absence of the {\\gamma} rotor. To explore how the intrinsic sequential performance arises, we computationally investigated essential inter-subunit couplings on the hexameric ring of mitochondrial and bacterial F1. We first reproduced the sequential hydrolysis schemes as experimentally detected, by simulating tri-site ATP hydrolysis cycles on the F1 ring upon kinetically imposing inter-subunit couplings to substantially promote the hydrolysis products release. We found that it is key for certain ATP binding and hydrolysis events to facilitate the neighbor-site ADP and Pi release to support the sequential hydrolysis. The kinetically feasible couplings were then scrutinized through atomistic molecular dynamics simulations as well as coarse-grained simulations, in which we enforced targeted conformational changes for the ATP binding or hydrolysis. Notably, we detected the asymmetrical neighbor-site opening that would facilitate the ADP release upon the enforced ATP binding, and computationally captured the complete Pi release through charge hopping upon the enforced neighbor-site ATP hydrolysis. The ATP-hydrolysis triggered Pi release revealed in current TMD simulation confirms a recent prediction made from statistical analyses of single molecule experimental data in regard to the role ATP hydrolysis plays. Our studies, therefore, elucidate both the concerted chemical kinetics and underlying structural dynamics of the inter-subunit couplings that lead to the rotary sequential hydrolysis of the F1 ring.

  8. Continuous enzymatic hydrolysis of lignocellulosic biomass with simultaneous detoxification and enzyme recovery.

    Science.gov (United States)

    Gurram, Raghu N; Menkhaus, Todd J

    2014-07-01

    Recovering hydrolysis enzymes and/or alternative enzyme addition strategies are two potential mechanisms for reducing the cost during the biochemical conversion of lignocellulosic materials into renewable biofuels and biochemicals. Here, we show that enzymatic hydrolysis of acid-pretreated pine wood with continuous and/or fed-batch enzyme addition improved sugar conversion efficiencies by over sixfold. In addition, specific activity of the hydrolysis enzymes (cellulases, hemicellulases, etc.) increased as a result of continuously washing the residual solids with removal of glucose (avoiding the end product inhibition) and other enzymatic inhibitory compounds (e.g., furfural, hydroxymethyl furfural, organic acids, and phenolics). As part of the continuous hydrolysis, anion exchange resin was tested for its dual application of simultaneous enzyme recovery and removal of potential enzymatic and fermentation inhibitors. Amberlite IRA-96 showed favorable adsorption profiles of inhibitors, especially furfural, hydroxymethyl furfural, and acetic acid with low affinity toward sugars. Affinity of hydrolysis enzymes to adsorb onto the resin allowed for up to 92 % of the enzymatic activity to be recovered using a relatively low-molar NaCl wash solution. Integration of an ion exchange column with enzyme recovery into the proposed fed-batch hydrolysis process can improve the overall biorefinery efficiency and can greatly reduce the production costs of lignocellulosic biorenewable products.

  9. Continuous-flow electro-assisted acid hydrolysis of granular potato starch via inductive methodology.

    Science.gov (United States)

    Li, Dandan; Yang, Na; Jin, Yamei; Guo, Lunan; Zhou, Yuyi; Xie, Zhengjun; Jin, Zhengyu; Xu, Xueming

    2017-08-15

    The induced electric field assisted hydrochloric acid (IEF-HCl) hydrolysis of potato starch was investigated in a fluidic system. The impact of various reaction parameters on the hydrolysis rate, including reactor number (1-4), salt type (KCl, MgCl 2 , FeCl 3 ), salt concentration (3-12%), temperature (40-55°C), and hydrolysis time (0-60h), were comprehensively assessed. Under optimal conditions, the maximum reducing sugar content in the hydrolysates was 10.59g/L. X-ray diffraction suggested that the crystallinity of IEF-HCl-modified starches increased with the intensification of hydrolysis but was lower than that of native starch. Scanning electron microscopy indicated that the surface and interior regions of starch granules were disrupted by the hydrolysis. The solubility of IEF-HCl-modified starches increased compared to native starch while their swelling power decreased, contributing to a decline in paste viscosity. These results suggest that IEF is a notable potential electrotechnology to conventional hydrolysis under mild conditions without any electrode touching the subject. Copyright © 2017 Elsevier Ltd. All rights reserved.

  10. Thermoluminescent dosimetric characterization of the perovskite, KMgF3, activated with lanthanum

    International Nuclear Information System (INIS)

    Sepulveda M, F.

    2003-01-01

    The new ICRP regulation about the Radiological Protection allows to the different groups to study new thermoluminescent materials highly sensitive for dosimetric applications (personal and environmental). This work reports the relative experimental results to the thermoluminescent characteristic of a new preparation of the fluorine perovskite activated with lanthanum absorbed in polytetrafluoroethylene (KMgF 3 : LaF 3 + Ptfe). The main thermoluminescent properties investigated were: the TL response like a function of the absorbed dose, the attainable accuracy in the dose measurement, the reproducibility of the TL readings and the threshold dose. The obtained results were compared with the requirements of the ANSI protocol for the environmental dosimetry, resulting in a very good agreement with the required yields. (Author)

  11. Lipase applications in oil hydrolysis with a case study on castor oil: a review.

    Science.gov (United States)

    Goswami, Debajyoti; Basu, Jayanta Kumar; De, Sirshendu

    2013-03-01

    Lipase (triacylglycerol acylhydrolase) is a unique enzyme which can catalyze various types of reactions such as hydrolysis, esterification, alcoholysis etc. In particular, hydrolysis of vegetable oil with lipase as a catalyst is widely studied. Free lipase, lipase immobilized on suitable support, lipase encapsulated in a reverse micelle and lipase immobilized on a suitable membrane to be used in membrane reactor are the most common ways of employing lipase in oil hydrolysis. Castor oil is a unique vegetable oil as it contains high amounts (90%) of a hydroxy monounsaturated fatty acid named ricinoleic acid. This industrially important acid can be obtained by hydrolysis of castor oil. Different conventional hydrolysis processes have certain disadvantages which can be avoided by a lipase-catalyzed process. The degree of hydrolysis varies widely for different lipases depending on the operating range of process variables such as temperature, pH and enzyme loading. Immobilization of lipase on a suitable support can enhance hydrolysis by suppressing thermal inactivation and estolide formation. The presence of metal ions also affects lipase-catalyzed hydrolysis of castor oil. Even a particular ion has different effects on the activity of different lipases. Hydrophobic organic solvents perform better than hydrophilic solvents during the reaction. Sonication considerably increases hydrolysis in case of lipolase. The effects of additives on the same lipase vary with their types. Nonionic surfactants enhance hydrolysis whereas cationic and anionic surfactants decrease it. A single variable optimization method is used to obtain optimum conditions. In order to eliminate its disadvantages, a statistical optimization method is used in recent studies. Statistical optimization shows that interactions between any two of the following pH, enzyme concentration and buffer concentration become significant in presence of a nonionic surfactant named Span 80.

  12. Kinetic study of hydrolysis of coconut fiber into glucose

    Science.gov (United States)

    Muhaimin, Sudiono, Sri

    2017-03-01

    Kinetic study of hydrolysis of coconut fiber into glucose has been done. The aim of this research was to study of the effect of time and temperature to the glucose as the result of the conversion of coconut fiber. The various temperature of the hydrolysis process were 30 °C, 48 °C, 72 °C and 95 °C and the various time of the hydrolysis process were 0, 15, 30, 60, 120, 180, 240, 300 minutes. A quantitative analysis was done by measured the concentration of the glucose as the result of the conversion of coconut fiber. The result showed that the rate constant from the various temperature were 3.10-4 minute-1; 8.10-4 minutees-1; 84.10-4 minute-1, and 205.10-4 minute-1, and the energy activation was 7,69. 103 kJ/mol.

  13. Effect of substituting cerium-rich mischmetal with lanthanum on high temperature properties of die-cast Mg-Zn-Al-Ca-RE alloys

    International Nuclear Information System (INIS)

    Anyanwu, Ifeanyi A.; Gokan, Yasuhiro; Suzuki, Atsuya; Kamado, Shigeharu; Kojima, Yo; Takeda, Suguru; Ishida, Taketoshi

    2004-01-01

    Mg-Zn-Al-Ca-RE alloys have been found to be promising materials for substituting aluminum alloys used for automatic transmission case applications in the automobile industry. Particularly, Mg-0.5%Zn-6%Al-1%Ca-3%RE (ZAXE05613) alloy exhibits comparable creep resistance as ADC12 die-casting aluminum alloy that is currently used for automatic transmission case applications. Changing the rare earth (RE) content of the alloy from mischmetal to lanthanum gives a further improvement in the creep properties of the alloy. Lanthanum addition results in the crystallization of a large amount of acicular Al 11 RE 3 (Al 11 La 3 ) compound along the grain boundaries as well as across the grain boundaries and this effectively controls grain boundary sliding and dislocation motion in the vicinity of the grain boundaries. As a result, die-cast ZAXLa05613 alloy exhibits a higher creep resistance than that of ZAXE05613 alloy

  14. Development of Volatile Compounds during Hydrolysis of Porcine Hemoglobin with Papain

    Directory of Open Access Journals (Sweden)

    Kathrine Holmgaard Bak

    2018-02-01

    Full Text Available There is a growing market for the use of hydrolysates from animal side-streams for production of high-protein supplements. However, there can be issues with development of off-flavors, either due to the raw material in question or due to the hydrolysis process itself. This study examined the development of volatile compounds during hydrolysis of hemoglobin. Briefly, porcine hemoglobin was hydrolyzed by 0.5% papain for up to 5 h, and the development of volatile compounds was analyzed via gas chromatography-mass spectrometry. The results showed that there was significant development of a number of volatile compounds with time, e.g., certain Maillard reaction and lipid oxidation products, which are likely candidates for the aroma development during hydrolysis. Furthermore, it was shown that development of a number of the volatiles was due to the hydrolysis process, as these compounds were not found in a control without enzyme.

  15. Optimization of Enzymatic Hydrolysis of Waste Bread before Fermentation

    OpenAIRE

    Hudečková, Helena; Šupinová, Petra; Ing. Mgr. Libor Babák, Ph.D., MBA

    2017-01-01

    Finding of optimal hydrolysis conditions is important for increasing the yield of saccharides. The higher yield of saccharides is usable for increase of the following fermentation effectivity. In this study optimal conditions (pH and temperature) for amylolytic enzymes were searched. As raw material was used waste bread. Two analytical methods for analysis were used. Efficiency and process of hydrolysis was analysed spectrophotometrically by Somogyi-Nelson method. Final yields of glucose were...

  16. Study of the Durability of Doped Lanthanum Manganite and Cobaltite Cathode Materials under ''Real World'' Air Exposure Atmospheres

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Prabhakar [Univ. of Connecticut, Storrs, CT (United States); Mahapatra, Manoj [Univ. of Connecticut, Storrs, CT (United States); Ramprasad, Rampi [Univ. of Connecticut, Storrs, CT (United States); Minh, Nguyen [Univ. of California, San Diego, CA (United States); Misture, Scott [Alfred Univ., NY (United States)

    2014-11-30

    The overall objective of the program is to develop and validate mechanisms responsible for the overall structural and chemical degradation of lanthanum manganite as well as lanthanum ferrite cobaltite based cathode when exposed to “real world” air atmosphere exposure conditions during SOFC systems operation. Of particular interest are the evaluation and analysis of degradation phenomena related to and responsible for (a) products formation and interactions with air contaminants, (b) dopant segregation and oxide exolution at free surfaces, (c) cation interdiffusion and reaction products formation at the buried interfaces, (d) interface morphology changes, lattice transformation and the development of interfacial porosity and (e) micro-cracking and delamination from the stack repeat units. Reaction processes have been studied using electrochemical and high temperature materials compatibility tests followed by structural and chemical characterization. Degradation hypothesis has been proposed and validated through further experimentation and computational simulation.

  17. Hydrolysis of ferric chloride in solution

    International Nuclear Information System (INIS)

    Lussiez, G.; Beckstead, L.

    1996-11-01

    The Detox trademark process uses concentrated ferric chloride and small amounts of catalysts to oxidize organic compounds. It is under consideration for oxidizing transuranic organic wastes. Although the solution is reused extensively, at some point it will reach the acceptable limit of radioactivity or maximum solubility of the radioisotopes. This solution could be cemented, but the volume would be increased substantially because of the poor compatibility of chlorides and cement. A process has been developed that recovers the chloride ions as HCl and either minimizes the volume of radioactive waste or permits recycling of the radioactive chlorides. The process involves a two-step hydrolysis at atmospheric pressure, or preferably under a slight vacuum, and relatively low temperature, about 200 degrees C. During the first step of the process, hydrolysis occurs according to the reaction below: FeCl 3 liquid + H 2 O → FeOCl solid + 2 HCl gas During the second step, the hot, solid, iron oxychloride is sprayed with water or placed in contact with steam, and hydrolysis proceeds to the iron oxide according to the following reaction: 2 FeOCl solid + H 2 O → Fe 2 O 3 solid + 2 HCl gas . The iron oxide, which contains radioisotopes, can then be disposed of by cementation or encapsulation. Alternately, these chlorides can be washed off of the solids and can then either be recycled or disposed of in some other way

  18. Effect of Acid mixtures on the Hydrolysis of Coconut Coir for ...

    African Journals Online (AJOL)

    MICHAEL HORSFALL

    and the independent variables (time, temperature, nitric acid concentration and acetic acid ... nitric and acetic acid as well as the hydrolysis time and temperature all positively influenced ..... Corn Starch Using Aspergillus niger. ... digestion and acid hydrolysis of nitrocellulose, ... Optimization of a-amylase production by.

  19. Formation of Lanthanum Hydroxide nano structures: Effect of NaOH and KOH solvents

    International Nuclear Information System (INIS)

    Mazloumi, M.; Zanganeh, S.; Kajbafvala, A.; Shayegh, M. R.; Sadrnezhaad, S. K.

    2008-01-01

    Lanthanum hydroxide (La(OH) 3 ) nano structures, including elliptical nanoparticles, octahedral rods and irregular nanoparticles were prepared chemically in NaOH and KOH solutions with 10 M concentration. The obtained powders were characterized with x-ray diffraction, scanning electron microscopy, transmission electron microscopy and differential thermal analysis. Crystallinities, morphologies and thermal behavior of the obtained nano structure powders were investigated under the influence of above mentioned solvents. The effect of chemical's temperature was also determined in one of the solvents (i.e. NaOH). The formation of growth in nano structure mechanism under the influence of alkali solutions (i.e., KOH and NaOH) have been discussed considerably in this paper

  20. Lactose Hydrolysis in Milk and Dairy Whey Using Microbial β-Galactosidases

    Directory of Open Access Journals (Sweden)

    Michele Dutra Rosolen

    2015-01-01

    Full Text Available This work aimed at evaluating the influence of enzyme concentration, temperature, and reaction time in the lactose hydrolysis process in milk, cheese whey, and whey permeate, using two commercial β-galactosidases of microbial origins. We used Aspergillus oryzae (at temperatures of 10 and 55°C and Kluyveromyces lactis (at temperatures of 10 and 37°C β-galactosidases, both in 3, 6, and 9 U/mL concentrations. In the temperature of 10°C, the K. lactis β-galactosidase enzyme is more efficient in the milk, cheese whey, and whey permeate lactose hydrolysis when compared to A. oryzae. However, in the enzyme reaction time and concentration conditions evaluated, 100% lactose hydrolysis was not reached using the K. lactis β-galactosidase. The total lactose hydrolysis in whey and permeate was obtained with the A. oryzae enzyme, when using its optimum temperature (55°C, at the end of a 12 h reaction, regardless of the enzyme concentration used. For the lactose present in milk, this result occurred in the concentrations of 6 and 9 U/mL, with the same time and temperature conditions. The studied parameters in the lactose enzymatic hydrolysis are critical for enabling the application of β-galactosidases in the food industry.