AMS radiocarbon dating of lacustrine sediment from an impact crater in northeastern China

Energy Technology Data Exchange (ETDEWEB)

Liu, K.X. [State Key Laboratory of Nuclear Physics and Technology and Institute of Heavy Ion Physics, School of Physics, Peking University, Beijing 100871 (China); Chen, M., E-mail: mchen@gig.ac.cn [Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, 510640 Guangzhou (China); Ding, X.F.; Fu, D.P. [State Key Laboratory of Nuclear Physics and Technology and Institute of Heavy Ion Physics, School of Physics, Peking University, Beijing 100871 (China); Ding, P. [State Key Laboratory of Isotope Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, 510640 Guangzhou (China); Shen, C.D., E-mail: cdshen@gig.ac.cn [State Key Laboratory of Isotope Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, 510640 Guangzhou (China); Xiao, W.S. [Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, 510640 Guangzhou (China)

2013-01-15

In order to investigate the origin and age of a bowl-shaped crater with 1.8 km diameter in northeastern China, a core drilling about 110 m in total was carried out in 2009 at the center of the crater. A 106-m-thick unit of lacustrine sediment is revealed under a surface layer of about 1 m of yellow soil. The impact origin has been confirmed based on geological analysis. In this paper, we report the AMS {sup 14}C dating results of lacustrine sediment. The data suggest that the meteorite impact in Xiuyan happened more than 50,000 years ago and a two-section linear relationship of {sup 14}C ages with the depth shows a stable sediment environment through the two time stages.

Chapter D: With or Without Salt-a Comparison of Marine and Continental-Lacustrine Diatomite Deposits

Science.gov (United States)

Moyle, Phillip R.; Dolley, Thomas P.

2003-01-01

Diatoms in sedimentary deposits of marine and continental, especially lacustrine, origin have similar nutrient (for example, phosphate, nitrate, and silica) and light requirements; however, their geologic ranges and physiographic environments vary. Marine diatoms range in age from Early Cretaceous to Holocene, and continental diatoms range in age from Eocene to Holocene; however, most commercial diatomites, both marine and lacustrine, were deposited during the Miocene. Marine deposits of commercial value generally accumulated along continental margins with submerged coastal basins and shelves where wind-driven boundary currents provided the nutrient-rich upwelling conditions capable of supporting a productive diatom habitat. Commercial freshwater diatomite deposits occur in volcanic terrains associated with events that formed sediment-starved drainage basins, such as the Basin and Range Province, particularly in Nevada. Marine habitats generally are characterized by stable conditions of temperature, salinity, pH, nutrients, and water currents, in contrast to lacustrine habitats, which are characterized by wide variations in these conditions. Marine deposits generally are of higher quality and contain larger resources, owing to their greater areal extent and thickness, whereas most of the world's known diatomites are of lacustrine origin. Both types of deposit are commonly mined by open-pit methods and subjected to processing designed to remove organic matter, CO2, pore water, and inorganic contaminants in order to produce purified products. The highest quality diatomites, predominantly from marine sources, are used in filtration, although both types of deposit produce filter grades, and additional end uses include fillers, additives, absorbents, and abrasives.

Lacustrine-humate model for primary uranium ore deposits, Grants Uranium Region, New Mexico

International Nuclear Information System (INIS)

Turner-Peterson, C.E.

1985-01-01

Two generations of uranium ore, primary and redistributed, occur in fluvial sandstones of the Upper Jurassic Morrison Formation in the San Juan basin; the two stages of ore formation can be related to the hydrologic history of the basin. Primary ore formed soon after Morrison deposition, in the Late Jurassic to Early Cretaceous, and a model, the lacustrine-humate model, is offered that views primary mineralization as a diagenetic event related to early pore fluid evolution. The basic premise is that the humate, a pore-filling organic material closely associated with primary ore, originated as humic acids dissolved in pore waters of greenish-gray lacustrine mudstones deposited in the mud-flat facies of the Brushy Basin Member and similar K shale beds in the Westwater Canyon Member. During compaction associated with early burial, formation water expelled from lacustrine mudstone units carried these humic acids into adjacent sandstone beds where the organics precipitated, forming the humate deposits that concentrated uranium. During the Tertiary, much later in the hydrologic history of the basin, when Jurassic sediments were largely compacted, oxygenated ground water flowed basinward from uplifted basin margins. This invasion of Morrison sandstone beds by oxidizing ground waters redistributed uranium from primary ores along redox boundaries, forming ore deposits that resemble roll-front-type uranium ores. 11 figures

The Upper Jurassic Stanleyville Group of the eastern Congo Basin: An example of perennial lacustrine system

Science.gov (United States)

Caillaud, Alexis; Blanpied, Christian; Delvaux, Damien

2017-08-01

The intracratonic Congo Basin, located in the Democratic Republic of Congo (DRC), is the largest sedimentary basin of Africa. The Jurassic strata outcrop along its eastern margin, south of Kisangani (formerly Stanleyville). In the last century, the Upper Jurassic Stanleyville Group was described as a lacustrine series containing a thin basal marine limestone designed as the ;Lime Fine; beds. Since the proposal of this early model, the depositional environment of the Stanleyville Group, and especially the possible marine incursion, has been debated, but without re-examining the existing cores, outcrop samples and historical fossils from the type location near Kisangani that are available at the Royal Museum for Central Africa (MRAC/KMMA, Tervuren, Belgium). In order to refine the former sedimentology, a series of nine exploration cores drilled in the Kisangani sub-basin have been described. This study aims at integrating sedimentary facies in existing sedimentary models and to discuss the hypothesis of the presence of Kimmeridgian marine deposits along the Congo River near Kisangani, a region which lies in the middle of the African continent. Eight facies have been identified, which permit a reinterpretation of the depositional environment and paleogeography of the Stanleyville Group. The base of the Stanleyville Group is interpreted to represent a conglomeratic fluvial succession, which filled an inherited Triassic paleotopography. Above these conglomerates, a transition to a typically lacustrine system is interpreted, which includes: (1) a basal profundal, sublittoral (brown to dark fine-grained siltstones with microbial carbonates, i.e., the ;Lime Fine; beds) and littoral lacustrine series; covered by (2) a sublittoral to profundal interval (brown to dark organic-rich, fine-grained siltstones), which corresponds to the maximum extent of the paleo-lake; and, finally (3) a shallow lacustrine series (greenish calcareous siltstones and sandstones with red siltstones

Volcanogenic Fluvial-Lacustrine Environments in Iceland and Their Utility for Identifying Past Habitability on Mars

Directory of Open Access Journals (Sweden)

Claire Cousins

2015-02-01

Full Text Available The search for once-habitable locations on Mars is increasingly focused on environments dominated by fluvial and lacustrine processes, such as those investigated by the Mars Science Laboratory Curiosity rover. The availability of liquid water coupled with the potential longevity of such systems renders these localities prime targets for the future exploration of Martian biosignatures. Fluvial-lacustrine environments associated with basaltic volcanism are highly relevant to Mars, but their terrestrial counterparts have been largely overlooked as a field analogue. Such environments are common in Iceland, where basaltic volcanism interacts with glacial ice and surface snow to produce large volumes of meltwater within an otherwise cold and dry environment. This meltwater can be stored to create subglacial, englacial, and proglacial lakes, or be released as catastrophic floods and proglacial fluvial systems. Sedimentary deposits produced by the resulting fluvial-lacustrine activity are extensive, with lithologies dominated by basaltic minerals, low-temperature alteration assemblages (e.g., smectite clays, calcite, and amorphous, poorly crystalline phases (basaltic glass, palagonite, nanophase iron oxides. This paper reviews examples of these environments, including their sedimentary deposits and microbiology, within the context of utilising these localities for future Mars analogue studies and instrument testing.

Volcanogenic fluvial-lacustrine environments in iceland and their utility for identifying past habitability on Mars.

Science.gov (United States)

Cousins, Claire

2015-02-16

The search for once-habitable locations on Mars is increasingly focused on environments dominated by fluvial and lacustrine processes, such as those investigated by the Mars Science Laboratory Curiosity rover. The availability of liquid water coupled with the potential longevity of such systems renders these localities prime targets for the future exploration of Martian biosignatures. Fluvial-lacustrine environments associated with basaltic volcanism are highly relevant to Mars, but their terrestrial counterparts have been largely overlooked as a field analogue. Such environments are common in Iceland, where basaltic volcanism interacts with glacial ice and surface snow to produce large volumes of meltwater within an otherwise cold and dry environment. This meltwater can be stored to create subglacial, englacial, and proglacial lakes, or be released as catastrophic floods and proglacial fluvial systems. Sedimentary deposits produced by the resulting fluvial-lacustrine activity are extensive, with lithologies dominated by basaltic minerals, low-temperature alteration assemblages (e.g., smectite clays, calcite), and amorphous, poorly crystalline phases (basaltic glass, palagonite, nanophase iron oxides). This paper reviews examples of these environments, including their sedimentary deposits and microbiology, within the context of utilising these localities for future Mars analogue studies and instrument testing.

Drowning unconformity of lacustrine rift basins: A case study from the Dongying Sag in Bohai Bay Basin, China

Science.gov (United States)

Chen, R.; Fan, J.

2015-12-01

The concept of drowning unconformity of lacustrine rift basins was proposed in this paper. This paper utilized 3D seismic data, well-log and the principles methods associated with structural geology, sedimentology and geochemistry, to analyze the drowning unconformity and discuss the origins of drowning unconformity in Dongying Sag in Bohai Bay Basin.Researching on it is not only important for a better understanding of tectonic evolution, palaeogeography and sedimentation of hydrocarbon source rocks, but also a vital guiding significance for the exploration of beach-bar sandstone reservoirs and shale oil.1. The concept of drowning unconformity of lacustrine rift basins is defined. With the consequences of rapid tectonic subsidence in basin, the sharp rise of lake-level and the increased rate of accommodation(A) in basin exceeded the rate of sediment supply(S),namely A>>S, the basin suddenly transformed into deep-water settings from shallow-water settings with sudden change of sediment transport and sediment dispersal patterns. 2.The sequence surface between Sha4 and Sha3 Member of Shahejie Formation is the drowning unconformity(43.5Ma). There are the sedimentary association of the reefs in shallow lacustrine, beach-bar sandstones and glutenite fan bodies under the surface. By contrast, there are the sedimentary association of deep-lake oil shales and shales over the surface. The drowning unconformity in Dongying Sag is a tectonic revolution surface which is changed from extensional tectonics to transtensional tectonics and it is also the surface of discontinuity from shallow lacustrine to deep lacustrine. The responses to sudden changes appeared in the parameters of geophysics, geochemistry and paleontology. 3. With the penetration of India into Asia plate in NNE trending,the subduction zones of Pacific Plate retreated. It caused the rapid downwelling of asthenospheric mantle, followed by the extensive drowning unconformity.

A note on coarse-grained gravity-flow deposits within proterozoic lacustrine sedimentary rocks, Transvaal sequence, South Africa

Science.gov (United States)

Eriksson, P. G.

A widely developed, thin, coarse-matrix conglomerate occurs within early Proterozoic lacustrine mudrocks in the Transvaal Sequence, South Africa. The poorly sorted tabular chert clasts, alternation of a planar clast fabric with disorientated zones, plus normal and inverse grading in the former rock type suggest deposition by density-modified grain-flow and high density turbidity currents. The lower fan-delta slope palæenvironment inferred for the conglomerate is consistent with the lacustrine interpretation for the enclosing mudrock facies. This intracratonic setting contrasts with the marine environment generally associated with density-modified grain-flow deposits.

Free and sulphurized hopanoids and highly branched isoprenoids in immature lacustrine oil shales

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Las Heras, F.X.C. de; Grimalt, J.O.; Lopez, J.F.; Albaiges, J.; Leeuw, J.W. de

1997-01-01

A study of the solvent extracts of four samples from two immature oil shales from Tertiary lacustrine basins, Ribesalbes and Campins (southern European rift system), deposited under reducing conditions, has allowed the identification of S-containing hopanoids and novel highly branched isoprenoids

A Middle-Upper Miocene fluvial-lacustrine rift sequence in the Song Ba Rift, Vietnam

DEFF Research Database (Denmark)

Lars H., Nielsen; Henrik I., Petersen; Nguyen D., Dau

2007-01-01

The small Neogene Krong Pa graben is situated within the continental Song Ba Rift, which is bounded by strike-slip faults that were reactivated as extensional faults in Middle Miocene time. The 500 m thick graben-fill shows an overall depositional development reflecting the structural evolution...... subsidence rate and possibly a higher influx of water from the axial river systems the general water level in the graben rose and deep lakes formed. High organic preservation in the lakes prompted the formation of two excellent oil-prone lacustrine source-rock units. In the late phase of the graben...... as carrier beds, whereas the braided fluvial sandstones and conglomerates along the graben margins may form reservoirs. The Krong Pa graben thus contains oil-prone lacustrine source rocks, effective conduits for generated hydrocarbons and reservoir sandstones side-sealed by the graben faults toward...

The Alleret Maar lacustrine sequence (French Massif Central): a 150 ka long early-middle Pleistocene continental paleoenvironmental record.

Science.gov (United States)

Nomade, S.; Pastre, J.; Guillou, H.; Gauthier, A.; Scaillet, S.

2008-12-01

Lacustrine maar sequences of the French Massif Central are of great interest for paleoclimatic and paleoenvironmental reconstructions of mid-latitudes Quaternary continental environments. In particular, the western Velay region yields exceptional sequences spanning the last 450 ka (Reille et al., J. Quat. Sci. 2000). However, older sequences remain largely unknown despite the presence of interbedded alkaline tephras allowing precise absolute radiochronological control of many lacustrine squences. The Alleret maar is a 1500 m wide phreatomagmatic crater that provides a long lacustrine sequence (41 m). The upper part of this sequence (AL2 core, 14.6 m) was studied between 2005 and 2006 (Pastre et al., C. R. Acad Sci, 2007). A 39Ar/40Ar date (557 ± 5ka) obtained from an interbedded tephra layer located at 7m as well as the associated pollen data attribute the beginning of this sequence to the MIS 15. Thanks to the AL3 core recovered in 2005 (40.6 m, CNRS Meudon) several new tephra layers were discovered in the bottom part of this lacustrine sequence. Three new 39Ar/40Ar ages (single crystal analyses) from trachytic tephra layers were obtained at the LSCE Argon Laboratory (France). These layers are located at -30.2, -36.2 and -39.2m. Ages obtained relative to the ACR-2 flux standard (1,201Ma, Kuiper et al., Science, 2008) range from 692 ± 6 ka (MSWD: 2.3, n=18) for the youngest (-30.2m) to 726 ± 9Ka Ka (MSWD: 2.2, n=12) for the lowest tephra located at -39.2m. These new dates indicate a relatively homogeneous deposition rate of 3.5cm/ka and that the last 10 meters cover the MIS 17-MIS18 period. According to these current radiochronological data the complete lacustrine sequence last more than 150ka. Ongoing sedimentary and pollen studies will allow to extend the paleoenvironmental and paleoclimatic records of the French Massif Central towards the beginning of the early middle Pleistocene.

Specificity of the Cyclic GMP-Binding Activity and of a Cyclic GMP-Dependent Cyclic GMP Phosphodiesterase in Dictyostelium discoideum

NARCIS (Netherlands)

Haastert, Peter J.M. van; Walsum, Hans van; Meer, Rob C. van der; Bulgakov, Roman; Konijn, Theo M.

1982-01-01

The nucleotide specificity of the cyclic GMP-binding activity in a homogenate of Dictyostelium discoideum was determined by competition of cyclic GMP derivatives with [8-3H] cyclic GMP for the binding sites. The results indicate that cyclic GMP is bound to the binding proteins by hydrogen bonds at

Observations on the relation between lacustrine facies and uranium deposits in continental sediments

International Nuclear Information System (INIS)

Noble, E.A.

1981-01-01

A recent sedimentological concept and approach in the evaluation of lacustrine deposition environments for their geological uranium potential are described. The presence of certain types of limonite seems to be a key factor in the process of leaching, the formation of pyrite and the precipitation of uranium. (author)

Characterization of Tertiary Catalan lacustrine oil shales: Discovery of extremely organic sulphur-rich Type I kerogens

Science.gov (United States)

Sinninghe Damsté, Jaap S.; de las Heras, F. Xavier C.; van Bergen, Pim F.; de Leeuw, Jan W.

1993-01-01

The kerogens of three Tertiary Catalan lacustrine oil shales were analyzed by light microscopy, flash pyrolysis-gas chromatography-mass spectrometry, and bulk composition methods (elemental analysis, Rock Eval pyrolysis). Two of the three kerogens (Ribesalbes and Campins) are extremely rich in organic sulphur (atomic S org/C ratio > 0.04) and hydrogen (atomic ratio H/C ratio > 1.5) and are, consequently, classified as Type I-S kerogens. Very characteristic distribution patterns of flash pyrolysis products (e.g., alkan-9- and -10-ones, alkadienes) of the Ribesalbes kerogen revealed that it is predominantly composed of fossilized organic matter of the freshwater alga Botryococcus braunii. These two findings demonstrate that sulphurization of organic matter may also occur in lacustrine sediments provided that sulphate is supplied by external sources. Data on the third kerogen sample (Cerdanya) suggest that the freshwater alga Pediastrum may contain a (partly) aromatic biomacromolecule that is selectively preserved upon diagenesis. These findings testify to the large variability in palaeodepositional conditions in lacustrine environments. A comparison of the biomarker composition of the extract of the Ribesalbes oil shale with the kerogen composition indicate that biomarkers often cannot be used to assess the major sources of organic matter in such settings. A similar conclusion can be drawn from a comparison of literature data concerning the Messel Oil Shale.

The microfauna assemblages as indicators of paleoenvironmental changes in the Miocene fluvial- lacustrine cycles (NE Duero Basin, Spain

Directory of Open Access Journals (Sweden)

A. Herrero-Hernández

2016-11-01

Full Text Available The siliclastic and carbonate deposits are interbedded in the Villadiego area (Miocene, NE Duero Basin. They have been subdivided into two high-rank depositional sequences: DDS and CDS. The sedimentary analysis of these units and the study of the microfauna content, mainly ostracods, led to the identification of lacustrine-fluvial interaction systems. The sedimentary characteristics reveal the existence of fluvial systems of gravel, flood plains and lacustrine systems that were interconnected and intimately related in north-south direction. In the sedimentological analysis, thirteen types of fluvial and lacustrine lithofacies and six genetic facies associations were recognized. The top of DDS is the result of lake level risings. The CDS shows a deepening-shallowing cycle. The ostracod micropaleontological analysis of the sediments have been studied, with the aim of reconstructing the palaeoenvironmental evolution of this area. These microfauna assemblages integrated with the analysis of the sedimentary facies allowed to conclude the existence of lakes with a water-bearing level of few tens of meters. A change in the chemical conditions of the waters, which evolved from oligohaline and carbonated to mesohaline and sulphated is concluded.

Lacustrine sedimentation and facies model for the last 45,000 yr in Chalco basin. Central Mexico

Science.gov (United States)

Ortega, B.; Lozano, S.; Caballero, M.; Herrera, D.

2013-05-01

Chalco basin in central Mexico (19° 15' N, 98° 58' W, 2200 m asl) is one of the most detailed lake sediment sequence analyzed in Mexico for paleoclimatic and paleoenvironmental studies. In this former lake, five drill cores up to 27 m depth were recovered in 1987-1989 by the UNAM team, and three cores covering most of the former sequence were obtained in 2008 and 2011. The upper 27 m of the Chalco lacustrine sequence contains the record of the last 45 kyr climate history in the northern American tropics. The active tectonic and volcanic setting of Chalco Lake in the Trans-Mexican Volcanic Belt, provides an opportunity to evaluate environmental (volcanic + tectonic vs. climatic) controls on lacustrine sedimentation. The establishment of a detailed time scale by 14C in pollen extracts provides an accurate chronological control. The stratigraphical and sedimentological analyses presented here provided the recognition of depositional environments and the architecture of the upper lacustrine succession. Sedimentary facies were defined on the basis of sedimentological descriptions, microscopic observation and compositional analyses. According to compositional criteria, facies were identified and groped into two main categories according to compositional criteria: 1) detrital and volcaniclastic, and 2) biogenic facies. The clastic facies includes massive to laminated, silty and clayey sediments composed of clay minerals, feldspars, amphiboles with minor amounts of quartz, opaque minerals and calcite. Diatoms are the most common biological remains in all the clastic facies. Most of the volcaniclastic deposits correspond to fall-out deposits, some of them of well documented eruptions of the nearby large stratovolcanoes Popocatepetl and Nevado de Toluca, which in turn serve as stratigraphical markers. The biogenic facies are massive to finely laminated diatom ooze and ostracod ooze layers. The sedimentary architecture of the lacustrine succession has been controlled by

Mechanosensory based orienting behaviors in fluvial and lacustrine populations of mottled sculpin (Cottus bairdi)

Science.gov (United States)

Sheryl Coombs; Gary D. Grossman

2006-01-01

We compared prey-orienting and rheotactic behaviors in a fluvial (Coweeta Creek) and lacustrine (Lake Michigan) population of mottled sculpin. Blinded sculpin from both populations exhibited unconditioned, mechanosensory based rheotaxis to low velocity flows. Whereas Lake Michigan sculpin generally showed increasing levels of positive rheotaxis to increasing velocities...

Devonian lacustrine shore zone architecture imaged with ground penetrating radar

DEFF Research Database (Denmark)

Andrews, Steven D.; Moreau, Julien; Archer, Stuart

. The shore zone sandstones overlie playa facies which contain abundant desiccation horizons, reflecting the most arid phase in the climatically controlled lacustrine cycle. As climatic conditions ameliorated the rejuvenation of fluvial systems resulted in the transport of sand out into the basin. Initial...... deposition was limited to intermittent events where sediment was laid down on a water saturated substrate. Some of these may have occurr­­­ed subaqueously as small scale turbidity flows. High resolution fluctuations in lake level resulted in periodic short lived reworking events along the lake margin which...

Lacustrine-fluvial interactions in Australia's Riverine Plains

Science.gov (United States)

Kemp, Justine; Pietsch, Timothy; Gontz, Allen; Olley, Jon

2017-06-01

Climatic forcing of fluvial systems has been a pre-occupation of geomorphological studies in Australia since the 1940s. In the Riverine Plain, southeastern Australia, the stable tectonic setting and absence of glaciation have combined to produce sediment loads that are amongst the lowest in the world. Surficial sediments and landforms exceed 140,000 yr in age, and geomorphological change recorded in the fluvial, fluvio-lacustrine and aeolian features have provided a well-studied record of Quaternary environmental change over the last glacial cycle. The region includes the Willandra Lakes, whose distinctive lunette lakes preserve a history of water-level variations and ecological change that is the cornerstone of Australian Quaternary chronostratigraphy. The lunette sediments also contain an ancient record of human occupation that includes the earliest human fossils yet found on the Australian continent. To date, the lake-level and palaeochannel records in the Lachlan-Willandra system have not been fully integrated, making it difficult to establish the regional significance of hydrological change. Here, we compare the Willandra Lakes environmental record with the morphology and location of fluvial systems in the lower Lachlan. An ancient channel belt of the Lachlan, Willandra Creek, acted as the main feeder channel to Willandra Lakes before channel avulsion caused the lakes to dry out in the late Pleistocene. Electromagnetic surveys, geomorphological and sedimentary evidence are used to reconstruct the evolution of the first new channel belt following the avulsion. Single grain optical dating of floodplain sediments indicates that sedimentation in the new Middle Billabong Palaeochannel had commenced before 18.4 ± 1.1 ka. A second avulsion shifted its upper reaches to the location of the present Lachlan River by 16.2 ± 0.9 ka. The timing of these events is consistent with palaeohydrological records reconstructed from Willandra Lakes and with the record of

Sulfur Geochemistry of a Lacustrine Record from Taiwan Reveals Enhanced Marine Aerosol Input during the Early Holocene.

Science.gov (United States)

Ding, Xiaodong; Li, Dawei; Zheng, Liwei; Bao, Hongyan; Chen, Huei-Fen; Kao, Shuh-Ji

2016-12-12

Lacustrine record of marine aerosol input has rarely been documented. Here, we present the sulfur geochemistry during the last deglaciation and early Holocene of a sediment core retrieved from the Dongyuan Lake in southern Taiwan. An unusually high sulfur peak accompanying pyrite presence is observed at 10.5 ka BP. Such high sulfur content in lacustrine record is unusual. The δ 34 S of sulfur varied from +9.5 to + 17.1‰ with two significant positive shifts at 10.5 and 9.4 ka BP. The sources of sulfur and potential processes involving the sulfur isotope variation including bacterial sulfate reduction, volcanic emissions, in-catchment sulfide oxidation and marine aerosol input are discussed. Enhanced marine aerosol input is the most likely explanation for such sulfur peaks and δ 34 S shifts. The positive δ 34 S shifts appeared concurrently with the maximum landslide events over Taiwan resulted from enhanced typhoon activities. The synchronicity among records suggests that increased typhoon activities promoted sea spray, and consequently enhanced the marine aerosol input with 34 S-enriched sulfate. Our sulfur geochemistry data revealed sea spray history and marine influence onto terrestrial environment at coastal regions. Wider coverage of spatial-temporal lacustrine sulfur geochemistry record is needed to validate the applicability of sulfur proxy in paleoenvironmental research.

Analysis of lithofacies cyclicity in the Miocene Coal Complex of the Bełchatów lignite deposit, south-central Poland

Directory of Open Access Journals (Sweden)

Mastej Wojciech

2015-12-01

Full Text Available Markov chain analysis was applied to studies of cyclic sedimentation in the Coal Complex of the Bełchatów mining field (part of the Bełchatów lignite deposit. The majority of ambiguous results of statistical testing that were caused by weak, statistically undetectable advantage of either cyclicity over environmental barriers or vice versa, could be explained if only the above-mentioned advantages appeared in the neighbourhood. Therefore, in order to enhance the credibility of statistical tests, a new approach is proposed here in that matrices of observed transition numbers from different boreholes should be added to increase statistical reliability if they originated in a homogeneous area. A second new approach, which consists of revealing statistically undetectable cyclicity of lithofacies alternations, is proposed as well. All data were derived from the mining data base in which differentiation between lithology and sedimentary environments was rather weak. For this reason, the methodological proposals are much more important than details of the sedimentation model in the present paper. Nevertheless, they did reveal some interesting phenomena which may prove important in the reconstruction of peat/lignite environmental conditions. First of all, the presence of cyclicity in the sedimentation model, i.e., cyclic alternation of channel and overbank deposits, represents a fluvial environment. It was also confirmed that the lacustrine subenvironment was cut off from a supply of clastic material by various types of mire barriers. Additionally, our analysis revealed new facts: (i these barriers also existed between lakes in which either carbonate or clay sedimentation predominated; (ii there was no barrier between rivers and lakes in which clay sedimentation predominated; (iii barriers were less efficient in alluvial fan areas but were perfectly tight in regions of phytogenic or carbonate sedimentation; (iv groundwater, rather than surface flow

Characterisation of Tertiary Catalan lacustrine oil shales: Discovery of extremely organic sulphur-rich type I kerogens

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Las Heras, F.X.C. de; Bergen, P.F. van; Leeuw, J.W. de

1993-01-01

The kerogens of three Tertiary Catalan lacustrine oil shales were analyzed by light microscopy, flash pyrolysis-gas chromatography-mass spectrometry, and bulk composition methods (elemental analysis, Rock Eval pyrolysis). Two of the three kerogens (Ribesalbes and Campins) are extremely rich in

Performance evaluation of nitrogen isotope ratio determination in marine and lacustrine sediments: An inter-laboratory comparison

NARCIS (Netherlands)

Bahlmann, E.; Bernasconi, S.M.; Bouillon, S.; Houtekamer, M.J.; Korntheuer, M.; Langenberg, F.; Mayr, C.; Metzke, M.; Middelburg, J.J.; Nagel, B.; Struck, U.; Voß, M.; Emeis, K.C.

2010-01-01

Nitrogen isotopes of organic matter are increasingly studied in marine biogeochemistry and geology, plant and animal ecology, and paleoceanography. Here, we present results of an inter-laboratory test on determination of nitrogen isotope ratios in marine and lacustrine sediments. Six different

On the equivalence of cyclic and quasi-cyclic codes over finite fields

Directory of Open Access Journals (Sweden)

Kenza Guenda

2017-07-01

Full Text Available This paper studies the equivalence problem for cyclic codes of length $p^r$ and quasi-cyclic codes of length $p^rl$. In particular, we generalize the results of Huffman, Job, and Pless (J. Combin. Theory. A, 62, 183--215, 1993, who considered the special case $p^2$. This is achieved by explicitly giving the permutations by which two cyclic codes of prime power length are equivalent. This allows us to obtain an algorithm which solves the problem of equivalency for cyclic codes of length $p^r$ in polynomial time. Further, we characterize the set by which two quasi-cyclic codes of length $p^rl$ can be equivalent, and prove that the affine group is one of its subsets.

Uranium and diagenesis in evaporitic lacustrine mudstone of the Oligocene White River Group, Dawes County, Nebraska. Bulletin

International Nuclear Information System (INIS)

Dickinson, K.A.

1991-01-01

The Oligocene White River Group consists of the Chadron and the overlying Brule Formations in northwestern Nebraska. The Chadron Formation consists of alluvial and colluvial vitric mudstone beds, but in addition contains white persistent layers (purplish-white layers) that probably resulted from soil formation on vitric parent material. West of the current study area a basal sandstone facies of the Chadron is host rock for the Crow Butte uranium deposit. The Brule, which consists mostly of pedogenically altered alluvial and fluvial vitric mudstone deposits, contains a uraniferous lacustrine facies northwest of Chadron, Nebraska. Detrital minerals in rocks of the White River Group include quartz, feldspar, volcanic glass, smectite, and illite. Chemical precipitate minerals in the lacustrine facies are calcite, dolomite, and gypsum. Authigenic minerals include calcite, dolomite, gypsum, smectite, opal, chalcedony, together with oxidized uranium minerals

Compressed sensing with cyclic-S Hadamard matrix for terahertz imaging applications

Science.gov (United States)

Ermeydan, Esra Şengün; ćankaya, Ilyas

2018-01-01

Compressed Sensing (CS) with Cyclic-S Hadamard matrix is proposed for single pixel imaging applications in this study. In single pixel imaging scheme, N = r . c samples should be taken for r×c pixel image where . denotes multiplication. CS is a popular technique claiming that the sparse signals can be reconstructed with samples under Nyquist rate. Therefore to solve the slow data acquisition problem in Terahertz (THz) single pixel imaging, CS is a good candidate. However, changing mask for each measurement is a challenging problem since there is no commercial Spatial Light Modulators (SLM) for THz band yet, therefore circular masks are suggested so that for each measurement one or two column shifting will be enough to change the mask. The CS masks are designed using cyclic-S matrices based on Hadamard transform for 9 × 7 and 15 × 17 pixel images within the framework of this study. The %50 compressed images are reconstructed using total variation based TVAL3 algorithm. Matlab simulations demonstrates that cyclic-S matrices can be used for single pixel imaging based on CS. The circular masks have the advantage to reduce the mechanical SLMs to a single sliding strip, whereas the CS helps to reduce acquisition time and energy since it allows to reconstruct the image from fewer samples.

Giving perspective to cliff exposures with ground penetrating radar: Devonian lacustrine shore zone architecture

Science.gov (United States)

Andrews, Steven; Moreau, Julien; Archer, Stuart

2015-04-01

The orbitally-controlled cyclic lacustrine successions of the Middle Devonian in Northern Scotland contains repeated developments of shore zone sandstones. However, due to the cliff-forming nature of the succession and the attitude of the sections through these sandstones, interpretation of this facies has been problematic. To better understand the shore zone systems, we carried out very high resolution sedimentary logging and constructed photo-panels which were combined with high resolution GPR profiling (250 MHz). To ensure close ties between the sedimentary logs and the GPR data, the cliffs were accessed using rope access techniques while GPR grids were shot directly above. The profiles were shot mainly in the strike direction of what was thought to be the shore elongation every 5-10 m and every 20-30 m in the dip direction. Shore zone systems of 3 different sequences have been imaged for a total of 1155 m of GPR profile collected. This configuration has allowed 3D visualisation of the architecture of the shore zone systems and, in combination with detailed sedimentology, provided insights into the generation of the dynamic shore zone environments. The coastal cliffs of northern Scotland expose sedimentary cycles on average 16-m-thick which record deep lake, perennial lake and playa environments. The shore zone deposits reach 2 to 3.5 m in thickness. Loading and discrete channel forms are recognised in both the GPR data and sedimentary logs through the lower portion of the lake shore zone successions. Up-section the sandstone beds appear to become amalgamated forming subtle low angle accretionary bar complexes which although visible in outcrop, after careful investigation, can be fully visualised and examined in the GPR data. The 3D visualisation allowed mapping the architecture and distribution of the bars . The orientation of these features, recognised from the survey, is consistent with extensive palaeocurrent measurements from oscillation ripples. Further

Z₂-double cyclic codes

OpenAIRE

Borges, J.

2014-01-01

A binary linear code C is a Z2-double cyclic code if the set of coordinates can be partitioned into two subsets such that any cyclic shift of the coordinates of both subsets leaves invariant the code. These codes can be identified as submodules of the Z2[x]-module Z2[x]/(x^r − 1) × Z2[x]/(x^s − 1). We determine the structure of Z2-double cyclic codes giving the generator polynomials of these codes. The related polynomial representation of Z2-double cyclic codes and its duals, and the relation...

Analysis of the variation of the compressibility index (Cc of volcanic clays and its application to estimate subsidence in lacustrine areas

Directory of Open Access Journals (Sweden)

D. Carreón-Freyre

2015-11-01

Full Text Available An analysis of the deformation conditions of lacustrine materials deposited at three sites in the volcanic valley of the Mexico City is presented. Currently geotechnical studies assume that compressibility of granular materials decreases in depth due to the lithostatic load. That means that the deeper the sample the more rigid is supposed to be, this assumption should be demonstrated by a decreased Compression Index (Cc in depth. Studies indicate that Mexico City clays exhibit brittle behaviour, and have high water content, low shear strength and variable Cc values. Furthermore, groundwater withdrawal below the city causes a differential decrease in pore pressure, which is related to the physical properties of granular materials (hydraulic conductivity, grain size distribution and conditions of formation. Our results show that Cc for fine grain materials (lacustrine can be vertically variable, particularly when soils and sediments are the product of different volcanic materials. Lateral and vertical variations in the distribution of the fluvio-lacustrine materials, especially in basins with recent volcanic activity, may be assessed by Cc index variations. These variations can also be related to differential deformation, nucleation and propagation of fractures and need to be considered when modelling land subsidence.

Chronology of Late Saalian and Middle Weichselian episodes of ice-free lacustrine sedimentation recorded in the Arumetsa section, southwestern Estonia

Directory of Open Access Journals (Sweden)

Maris Rattas

2010-06-01

Full Text Available The information obtained from a 21 m thick open-pit section of silty-clayey sediments in the Arumetsa bedrock valley, southwestern Estonia, revealed that lacustrine to glaciolacustrine sedimentation at the site started prior to 151 ka ago and lasted to about the end of marine isotope stage 6 (MIS6 at 130 ka. Further down from the 151 ka age-level to the bottom of the buried valley there are ca 60 m of lacustrine fine-grained sediments, the age of which remains still unclear. The Late Saalian sediments at Arumetsa are discordantly overlain by Middle Weichselian clay, silt and sand, deposited between ca 44 and 37 ka ago. As testified by optically stimulated luminescence (OSL ages, and pollen and diatom record, the Middle Weichselian fine-grained sediments contain redeposited Holsteinian but no Eemian pollen, and have not been fully bleached during deposition. Chronological, microfossil and sedimentological data show two hiatuses in the Arumetsa section. The first hiatus has left no sedimentary evidence for the period between ca 130 ka and 44 ka ago (MIS5 to older half of MIS3. The younger hiatus from ca 37 to 22 ka occurs between the Middle Weichselian lacustrine silt and the Late Weichselian till layer on top of the section.

Palaeoenvironmental implications of a Holocene sequence of lacustrine-peat sediments from the desert-loess transitional zone in Northern China

Science.gov (United States)

Jia, Feifei; Lu, Ruijie; Liu, Xiaokang; Zhao, Chao; Lv, Zhiqiang; Gao, Shangyu

2018-05-01

A high-resolution lacustrine-peat record from the desert-loess transitional zone in Northern China was obtained to reconstruct Holocene environmental change in the region. AMS 14C dates are used to provide a chronology. The results indicate that the site was a desert environment before 12.2 cal kyr BP, and was then occupied by a paleolake which started to shrink, with a wetland occurring from 6.2 to 3.0 cal kyr BP. Subsequently, the site became a seasonally water-filled depression. Based on the lithology and measurements of grain size and total organic carbon content, the climate changed from arid to humid at 12.2 cal kyr BP, and became more humid after 8.3 cal kyr BP. From 6.2 to 3.0 cal kyr BP, precipitation decreased but the climate remained at an optimum. After 3.0 cal kyr BP, the climate was dry overall but with several humid intervals. A comparison of paleoclimatic records from lacustrine and aeolian deposits from the region reveals a discrepancy about the nature of the early Holocene climate, and we conclude that this is because lacustrine sediments responded more sensitively to precipitation than aeolian deposits when the temperature was low. The environmental evolution of the region was synchronous with changes in the Asian summer monsoon (ASM), but temperature also played a key role in the early Holocene.

Genesis and distribution pattern of carbonate cements in lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation in the Dongying Sag, Jiyang Depression, Eastern China

DEFF Research Database (Denmark)

Yang, Tian; Cao, Yingchang; Friis, Henrik

2018-01-01

The lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation are the main exploration target for hydrocarbons in the Dongying Sag, Eastern China. Carbonate cementation is responsible for much of the porosity and permeability reduction in the lacustrine...

Cyclic Voltammograms from First Principles

DEFF Research Database (Denmark)

Karlberg, Gustav; Jaramillo, Thomas; Skulason, Egill

2007-01-01

Cyclic voltammetry is a fundamental experimental tool for characterizing electrochemical surfaces. Whereas cyclic voltammetry is widely used within the field of electrochemistry, a way to quantitatively and directly relate the cyclic voltammogram to ab initio calculations has been lacking, even f...

A Habitable Fluvio-Lacustrine Environment at Yellowknife Bay, Gale Crater, Mars

Science.gov (United States)

Grotzinger, J. P.; Sumner, D. Y.; Kah, L. C.; Stack, K.; Gupta, S.; Edgar, L.; Rubin, D.; Lewis, K.; Schieber, J.; Mangold, N.; Milliken, R.; Conrad, P. G.; DesMarais, D.; Farmer, J.; Siebach, K.; Calef, F.; Hurowitz, J.; McLennan, S. M.; Ming, D.; Vaniman, D.; Crisp, J.; Vasavada, A.; Edgett, K. S.; Malin, M.; Blake, D.; Gellert, R.; Mahaffy, P.; Wiens, R. C.; Maurice, S.; Grant, J. A.; Wilson, S.; Anderson, R. C.; Beegle, L.; Arvidson, R.; Hallet, B.; Sletten, R. S.; Rice, M.; Bell, J.; Griffes, J.; Ehlmann, B.; Anderson, R. B.; Bristow, T. F.; Dietrich, W. E.; Dromart, G.; Eigenbrode, J.; Fraeman, A.; Hardgrove, C.; Herkenhoff, K.; Jandura, L.; Kocurek, G.; Lee, S.; Leshin, L. A.; Leveille, R.; Limonadi, D.; Maki, J.; McCloskey, S.; Meyer, M.; Minitti, M.; Newsom, H.; Oehler, D.; Okon, A.; Palucis, M.; Parker, T.; Rowland, S.; Schmidt, M.; Squyres, S.; Steele, A.; Stolper, E.; Summons, R.; Treiman, A.; Williams, R.; Yingst, A.; MSL Science Team; Kemppinen, Osku; Bridges, Nathan; Johnson, Jeffrey R.; Cremers, David; Godber, Austin; Wadhwa, Meenakshi; Wellington, Danika; McEwan, Ian; Newman, Claire; Richardson, Mark; Charpentier, Antoine; Peret, Laurent; King, Penelope; Blank, Jennifer; Weigle, Gerald; Li, Shuai; Robertson, Kevin; Sun, Vivian; Baker, Michael; Edwards, Christopher; Farley, Kenneth; Miller, Hayden; Newcombe, Megan; Pilorget, Cedric; Brunet, Claude; Hipkin, Victoria; Léveillé, Richard; Marchand, Geneviève; Sánchez, Pablo Sobrón; Favot, Laurent; Cody, George; Flückiger, Lorenzo; Lees, David; Nefian, Ara; Martin, Mildred; Gailhanou, Marc; Westall, Frances; Israël, Guy; Agard, Christophe; Baroukh, Julien; Donny, Christophe; Gaboriaud, Alain; Guillemot, Philippe; Lafaille, Vivian; Lorigny, Eric; Paillet, Alexis; Pérez, René; Saccoccio, Muriel; Yana, Charles; Armiens-Aparicio, Carlos; Rodríguez, Javier Caride; Blázquez, Isaías Carrasco; Gómez, Felipe Gómez; Gómez-Elvira, Javier; Hettrich, Sebastian; Malvitte, Alain Lepinette; Jiménez, Mercedes Marín; Martínez-Frías, Jesús; Martín-Soler, Javier; Martín-Torres, F. Javier; Jurado, Antonio Molina; Mora-Sotomayor, Luis; Caro, Guillermo Muñoz; López, Sara Navarro; Peinado-González, Verónica; Pla-García, Jorge; Manfredi, José Antonio Rodriguez; Romeral-Planelló, Julio José; Fuentes, Sara Alejandra Sans; Martinez, Eduardo Sebastian; Redondo, Josefina Torres; Urqui-O'Callaghan, Roser; Mier, María-Paz Zorzano; Chipera, Steve; Lacour, Jean-Luc; Mauchien, Patrick; Sirven, Jean-Baptiste; Manning, Heidi; Fairén, Alberto; Hayes, Alexander; Joseph, Jonathan; Sullivan, Robert; Thomas, Peter; Dupont, Audrey; Lundberg, Angela; Melikechi, Noureddine; Mezzacappa, Alissa; DeMarines, Julia; Grinspoon, David; Reitz, Günther; Prats, Benito; Atlaskin, Evgeny; Genzer, Maria; Harri, Ari-Matti; Haukka, Harri; Kahanpää, Henrik; Kauhanen, Janne; Paton, Mark; Polkko, Jouni; Schmidt, Walter; Siili, Tero; Fabre, Cécile; Wray, James; Wilhelm, Mary Beth; Poitrasson, Franck; Patel, Kiran; Gorevan, Stephen; Indyk, Stephen; Paulsen, Gale; Bish, David; Gondet, Brigitte; Langevin, Yves; Geffroy, Claude; Baratoux, David; Berger, Gilles; Cros, Alain; d'Uston, Claude; Forni, Olivier; Gasnault, Olivier; Lasue, Jérémie; Lee, Qiu-Mei; Meslin, Pierre-Yves; Pallier, Etienne; Parot, Yann; Pinet, Patrick; Schröder, Susanne; Toplis, Mike; Lewin, Éric; Brunner, Will; Heydari, Ezat; Achilles, Cherie; Sutter, Brad; Cabane, Michel; Coscia, David; Szopa, Cyril; Robert, François; Sautter, Violaine; Le Mouélic, Stéphane; Nachon, Marion; Buch, Arnaud; Stalport, Fabien; Coll, Patrice; François, Pascaline; Raulin, François; Teinturier, Samuel; Cameron, James; Clegg, Sam; Cousin, Agnès; DeLapp, Dorothea; Dingler, Robert; Jackson, Ryan Steele; Johnstone, Stephen; Lanza, Nina; Little, Cynthia; Nelson, Tony; Williams, Richard B.; Jones, Andrea; Kirkland, Laurel; Baker, Burt; Cantor, Bruce; Caplinger, Michael; Davis, Scott; Duston, Brian; Fay, Donald; Harker, David; Herrera, Paul; Jensen, Elsa; Kennedy, Megan R.; Krezoski, Gillian; Krysak, Daniel; Lipkaman, Leslie; McCartney, Elaina; McNair, Sean; Nixon, Brian; Posiolova, Liliya; Ravine, Michael; Salamon, Andrew; Saper, Lee; Stoiber, Kevin; Supulver, Kimberley; Van Beek, Jason; Van Beek, Tessa; Zimdar, Robert; French, Katherine Louise; Iagnemma, Karl; Miller, Kristen; Goesmann, Fred; Goetz, Walter; Hviid, Stubbe; Johnson, Micah; Lefavor, Matthew; Lyness, Eric; Breves, Elly; Dyar, M. Darby; Fassett, Caleb; Edwards, Laurence; Haberle, Robert; Hoehler, Tori; Hollingsworth, Jeff; Kahre, Melinda; Keely, Leslie; McKay, Christopher; Bleacher, Lora; Brinckerhoff, William; Choi, David; Dworkin, Jason P.; Floyd, Melissa; Freissinet, Caroline; Garvin, James; Glavin, Daniel; Harpold, Daniel; Martin, David K.; McAdam, Amy; Pavlov, Alexander; Raaen, Eric; Smith, Michael D.; Stern, Jennifer; Tan, Florence; Trainer, Melissa; Posner, Arik; Voytek, Mary; Aubrey, Andrew; Behar, Alberto; Blaney, Diana; Brinza, David; Christensen, Lance; DeFlores, Lauren; Feldman, Jason; Feldman, Sabrina; Flesch, Gregory; Jun, Insoo; Keymeulen, Didier; Mischna, Michael; Morookian, John Michael; Pavri, Betina; Schoppers, Marcel; Sengstacken, Aaron; Simmonds, John J.; Spanovich, Nicole; Juarez, Manuel de la Torre; Webster, Christopher R.; Yen, Albert; Archer, Paul Douglas; Cucinotta, Francis; Jones, John H.; Morris, Richard V.; Niles, Paul; Rampe, Elizabeth; Nolan, Thomas; Fisk, Martin; Radziemski, Leon; Barraclough, Bruce; Bender, Steve; Berman, Daniel; Dobrea, Eldar Noe; Tokar, Robert; Cleghorn, Timothy; Huntress, Wesley; Manhès, Gérard; Hudgins, Judy; Olson, Timothy; Stewart, Noel; Sarrazin, Philippe; Vicenzi, Edward; Bullock, Mark; Ehresmann, Bent; Hamilton, Victoria; Hassler, Donald; Peterson, Joseph; Rafkin, Scot; Zeitlin, Cary; Fedosov, Fedor; Golovin, Dmitry; Karpushkina, Natalya; Kozyrev, Alexander; Litvak, Maxim; Malakhov, Alexey; Mitrofanov, Igor; Mokrousov, Maxim; Nikiforov, Sergey; Prokhorov, Vasily; Sanin, Anton; Tretyakov, Vladislav; Varenikov, Alexey; Vostrukhin, Andrey; Kuzmin, Ruslan; Clark, Benton; Wolff, Michael; Botta, Oliver; Drake, Darrell; Bean, Keri; Lemmon, Mark; Schwenzer, Susanne P.; Lee, Ella Mae; Sucharski, Robert; Hernández, Miguel Ángel de Pablo; Ávalos, Juan José Blanco; Ramos, Miguel; Kim, Myung-Hee; Malespin, Charles; Plante, Ianik; Muller, Jan-Peter; Navarro-González, Rafael; Ewing, Ryan; Boynton, William; Downs, Robert; Fitzgibbon, Mike; Harshman, Karl; Morrison, Shaunna; Kortmann, Onno; Williams, Amy; Lugmair, Günter; Wilson, Michael A.; Jakosky, Bruce; Balic-Zunic, Tonci; Frydenvang, Jens; Jensen, Jaqueline Kløvgaard; Kinch, Kjartan; Koefoed, Asmus; Madsen, Morten Bo; Stipp, Susan Louise Svane; Boyd, Nick; Campbell, John L.; Perrett, Glynis; Pradler, Irina; VanBommel, Scott; Jacob, Samantha; Owen, Tobias; Savijärvi, Hannu; Boehm, Eckart; Böttcher, Stephan; Burmeister, Sönke; Guo, Jingnan; Köhler, Jan; García, César Martín; Mueller-Mellin, Reinhold; Wimmer-Schweingruber, Robert; Bridges, John C.; McConnochie, Timothy; Benna, Mehdi; Franz, Heather; Bower, Hannah; Brunner, Anna; Blau, Hannah; Boucher, Thomas; Carmosino, Marco; Atreya, Sushil; Elliott, Harvey; Halleaux, Douglas; Rennó, Nilton; Wong, Michael; Pepin, Robert; Elliott, Beverley; Spray, John; Thompson, Lucy; Gordon, Suzanne; Ollila, Ann; Williams, Joshua; Vasconcelos, Paulo; Bentz, Jennifer; Nealson, Kenneth; Popa, Radu; Moersch, Jeffrey; Tate, Christopher; Day, Mackenzie; Francis, Raymond; McCullough, Emily; Cloutis, Ed; ten Kate, Inge Loes; Scholes, Daniel; Slavney, Susan; Stein, Thomas; Ward, Jennifer; Berger, Jeffrey; Moores, John E.

2014-01-01

The Curiosity rover discovered fine-grained sedimentary rocks, which are inferred to represent an ancient lake and preserve evidence of an environment that would have been suited to support a martian biosphere founded on chemolithoautotrophy. This aqueous environment was characterized by neutral pH, low salinity, and variable redox states of both iron and sulfur species. Carbon, hydrogen, oxygen, sulfur, nitrogen, and phosphorus were measured directly as key biogenic elements; by inference, phosphorus is assumed to have been available. The environment probably had a minimum duration of hundreds to tens of thousands of years. These results highlight the biological viability of fluvial-lacustrine environments in the post-Noachian history of Mars.

Cyclic nucleotides and radioresistnace

International Nuclear Information System (INIS)

Kulinskij, V.I.; Mikheeva, G.A.; Zel'manovich, B.M.

1982-01-01

The addition of glucose to meat-peptone broth does not change the radiosensitizing effect (RSE) of cAMP at the logarithmic phase (LP) and the radioprotective effect (RPE) at the stationary phase (SP), but sensitization, characteristic of cGMP, disappears in SP and turns into RPE in LP. Introduction of glucose into the broth for 20 min eliminates all the effects of both cyclic nucleotides in the cya + strain while cya - mutant exhibits RSE. RSE of both cyclic nucleotides is only manifested on minimal media. These data brought confirmation of the dependence of the influence of cyclic media. These data brought confirmation of the dependence of the influence of cyclic nucleotides on radioresistance upon the metabolic status of the cell [ru

Visual search of cyclic spatio-temporal events

Science.gov (United States)

Gautier, Jacques; Davoine, Paule-Annick; Cunty, Claire

2018-05-01

The analysis of spatio-temporal events, and especially of relationships between their different dimensions (space-time-thematic attributes), can be done with geovisualization interfaces. But few geovisualization tools integrate the cyclic dimension of spatio-temporal event series (natural events or social events). Time Coil and Time Wave diagrams represent both the linear time and the cyclic time. By introducing a cyclic temporal scale, these diagrams may highlight the cyclic characteristics of spatio-temporal events. However, the settable cyclic temporal scales are limited to usual durations like days or months. Because of that, these diagrams cannot be used to visualize cyclic events, which reappear with an unusual period, and don't allow to make a visual search of cyclic events. Also, they don't give the possibility to identify the relationships between the cyclic behavior of the events and their spatial features, and more especially to identify localised cyclic events. The lack of possibilities to represent the cyclic time, outside of the temporal diagram of multi-view geovisualization interfaces, limits the analysis of relationships between the cyclic reappearance of events and their other dimensions. In this paper, we propose a method and a geovisualization tool, based on the extension of Time Coil and Time Wave, to provide a visual search of cyclic events, by allowing to set any possible duration to the diagram's cyclic temporal scale. We also propose a symbology approach to push the representation of the cyclic time into the map, in order to improve the analysis of relationships between space and the cyclic behavior of events.

Molecular isotopic characterisation of hydrocarbon biomarkers in Palaeocene-Eocene evaporitic, lacustrine source rocks from the Jianghan Basin, China

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Grice, Kliti; Schouten, S.; Peters, Kenneth E.

1998-01-01

Immature organic matter in lacustrine source rocks from the Jianghan Basin, eastern China, was studied for distributions and stable carbon isotopic compositions (13C) of hydrocarbon biomarkers. All of the bitumens contain isorenieratane (13C ca. −17 ) indicating the presence of Chlorobiaceae, and

The arabidopsis cyclic nucleotide interactome

KAUST Repository

Donaldson, Lara Elizabeth

2016-05-11

Background Cyclic nucleotides have been shown to play important signaling roles in many physiological processes in plants including photosynthesis and defence. Despite this, little is known about cyclic nucleotide-dependent signaling mechanisms in plants since the downstream target proteins remain unknown. This is largely due to the fact that bioinformatics searches fail to identify plant homologs of protein kinases and phosphodiesterases that are the main targets of cyclic nucleotides in animals. Methods An affinity purification technique was used to identify cyclic nucleotide binding proteins in Arabidopsis thaliana. The identified proteins were subjected to a computational analysis that included a sequence, transcriptional co-expression and functional annotation analysis in order to assess their potential role in plant cyclic nucleotide signaling. Results A total of twelve cyclic nucleotide binding proteins were identified experimentally including key enzymes in the Calvin cycle and photorespiration pathway. Importantly, eight of the twelve proteins were shown to contain putative cyclic nucleotide binding domains. Moreover, the identified proteins are post-translationally modified by nitric oxide, transcriptionally co-expressed and annotated to function in hydrogen peroxide signaling and the defence response. The activity of one of these proteins, GLYGOLATE OXIDASE 1, a photorespiratory enzyme that produces hydrogen peroxide in response to Pseudomonas, was shown to be repressed by a combination of cGMP and nitric oxide treatment. Conclusions We propose that the identified proteins function together as points of cross-talk between cyclic nucleotide, nitric oxide and reactive oxygen species signaling during the defence response.

Predominance of even carbon-numbered n-alkanes from lacustrine sediments in Linxia Basin, NE Tibetan Plateau: Implications for climate change

International Nuclear Information System (INIS)

Wang Yongli; Fang Xiaomin; Zhang Tongwei; Li Yuanmao; Wu Yingqin; He Daxiang; Wang Youxiao

2010-01-01

Research highlights: → This study reports the first observation of predominant even carbon-numbered n-alkanes of sediments in the continuous lacustrine-sedimentary section (Maogou) from the Late Miocene to the Early Pliocene (13-4.4 Ma) in the Linxia Basin, NE Tibetan Plateau. → Certain types of special autochthonous bacteria are a possible source for the special distribution of even carbon-numbered n-alkanes in lacustrine sediments. → These bacteria may have a high production rate in weak oxic-anoxic and arid depositional environments, in which a variety of geochemical parameters have recorded palaeoclimate change. → A close correspondence among the low ratio of n-C 27 /n-C 31 , the heavy δ 13 C values of TOC and a strong even carbon-number predominance (low OEP 16-20 values) from approximately 6.5 to 4.4 Ma and at approximately 8 Ma in the studied section suggests that n-alkanes with a high predominance of even carbon-numbers may be treated as geochemical proxies for arid climate. - Abstract: This study reports the first observation of predominant even C-numbered n-alkanes from sediments in the continuous lacustrine-sedimentary section (Maogou) from the Late Miocene to the Early Pliocene (13-4.4 Ma) in the Linxia Basin, NE Tibetan Plateau. The n-alkanes showed a bimodal distribution that is characterised by a centre at n-C 16 -n-C 20 with maximum values at n-C 18 and n-C 27 -n-C 31 as well as at n-C 29 . The first mode shows a strong even C-number predominance (OEP 16-20 0.34-0.66). In contrast, the second mode has a strong odd C-number predominance (OEP 27-31 1.20-2.45). Certain types of special autochthonous bacteria are a possible source for this distribution of even C-numbered n-alkanes in lacustrine sediments. These bacteria may have a high production rate in weak oxic-anoxic and arid depositional environments, in which a variety of geochemical parameters have recorded palaeoclimate change.

Manual for Cyclic Triaxial Test

DEFF Research Database (Denmark)

Shajarati, Amir; Sørensen, Kris Wessel; Nielsen, Søren Kjær

This manual describes the different steps that is included in the procedure for conducting a cyclic triaxial test at the geotechnical Laboratory at Aalborg University. Furthermore it contains a chapter concerning some of the background theory for the static triaxial tests. The cyclic/dynamic tria......This manual describes the different steps that is included in the procedure for conducting a cyclic triaxial test at the geotechnical Laboratory at Aalborg University. Furthermore it contains a chapter concerning some of the background theory for the static triaxial tests. The cyclic...

Ecological state of the Romanian Black Sea littoral lacustrine ecosystems

Science.gov (United States)

Gomoiu, M.-T.

2009-04-01

The author uses the results of his own researches as well as data from specialty literature to assess the ecological state of some typical lacustrine ecosystems considered, about 50 years ago, of major importance by their functions, services and researches, for the human populations in the settlements nearby. Based on this assessment the author recommends a few criteria which can be taken into account when programs of integrated management of these coastal ecosystems are initiated. The paper focuses on the study cases regarding the following major ecosystems: 1. Razelm-Sinoie Lagoon Complex - tightly linked to the Danube River and Delta systems, 2. Taşaul Lake - interfered in the last two decades by a branch of the DanubeRiver - Black Sea Canal and 3. Techirghiol Lake - for a long time under the sea level, a hyperhaline lake with therapeutic, sapropelic mud, disturbed by huge quantities of freshwaters infiltrated from the irrigation system. At present, the state of the lacustrine ecosystems at the Romanian Black Sea Coast can be characterized, mainly, by the following aspects: · Increase in the quantities of nutrients and chemical toxicants; · Rise in the level and frequency of eutrophication and pollution phenomena; · Drastic reduction of specific diversity; · Simplification of communities' structure - biocoenosis homogeneity; · Decrease in numerical abundance and biomass of benthic populations and consequently, low biofilter power by the decrease of the filter-feeder populations; · Worsening of the qualitative and the quantitative state of the biological benthic resources; · Thriving opportunistic forms (e.g. the worms causing sediment bioturbation); · Invasion by some exotic species, with harmful, unexpected consequences; · All populations undergo quantitative fluctuations; · Decrease in the fish population and in the use values of lacustrine assets, with strong impact on the welfare of the human society. Almost all pressure forms associated with the

Truce with oxygen - A naerobiosis outcompete aerobiosis in the Antarctic lacustrine bacteria

Digital Repository Service at National Institute of Oceanography (India)

LokaBharathi, P.A.; Nair, S.; DeSouza, M.J.B.D.; Chandramohan, D.

. All colonies that were not black by sulfide precipitation were counted as FB. The anaerobic CFU were AnB, FB, SRB, and TDLO. The plates were incubated at 8–10° C for 10–20 days and the tubes for ca 30 days. All samples have been analysed... aerobiosis in the Antarctic lacustrine bacteria Page 3 of 5 file://C:\\My Documents\\articles23.htm 2/11/05 sulfide (63–188 ppm) at 5° C for 16 h and the viability estimated using Kogure’s method10,11. Viability is expressed as percentage of total viable...

Architecture and reservoir quality of low-permeable Eocene lacustrine turbidite sandstone from the Dongying Depression, East China

Science.gov (United States)

Munawar, Muhammad Jawad; Lin, Chengyan; Chunmei, Dong; Zhang, Xianguo; Zhao, Haiyan; Xiao, Shuming; Azeem, Tahir; Zahid, Muhammad Aleem; Ma, Cunfei

2018-05-01

The architecture and quality of lacustrine turbidites that act as petroleum reservoirs are less well documented. Reservoir architecture and multiscale heterogeneity in turbidites represent serious challenges to production performance. Additionally, establishing a hierarchy profile to delineate heterogeneity is a challenging task in lacustrine turbidite deposits. Here, we report on the turbidites in the middle third member of the Eocene Shahejie Formation (Es3), which was deposited during extensive Middle to Late Eocene rifting in the Dongying Depression. Seismic records, wireline log responses, and core observations were integrated to describe the reservoir heterogeneity by delineating the architectural elements, sequence stratigraphic framework and lithofacies assemblage. A petrographic approach was adopted to constrain microscopic heterogeneity using an optical microscope, routine core analyses and X-ray diffraction (XRD) analyses. The Es3m member is interpreted as a sequence set composed of four composite sequences: CS1, CS2, CS3 and CS4. A total of forty-five sequences were identified within these four composite sequences. Sand bodies were mainly deposited as channels, levees, overbank splays, lobes and lobe fringes. The combination of fining-upward and coarsening-upward lithofacies patterns in the architectural elements produces highly complex composite flow units. Microscopic heterogeneity is produced by diagenetic alteration processes (i.e., feldspar dissolution, authigenic clay formation and quartz cementation). The widespread kaolinization of feldspar and mobilization of materials enhanced the quality of the reservoir by producing secondary enlarged pores. In contrast, the formation of pore-filling authigenic illite and illite/smectite clays reduced its permeability. Recovery rates are higher in the axial areas and smaller in the marginal areas of architectural elements. This study represents a significant insight into the reservoir architecture and

Deformation mechanisms in cyclic creep and fatigue

International Nuclear Information System (INIS)

Laird, C.

1979-01-01

Service conditions in which static and cyclic loading occur in conjunction are numerous. It is argued that an understanding of cyclic creep and cyclic deformation are necessary both for design and for understanding creep-fatigue fracture. Accordingly a brief, and selective, review of cyclic creep and cyclic deformation at both low and high strain amplitudes is provided. Cyclic loading in conjunction with static loading can lead to creep retardation if cyclic hardening occurs, or creep acceleration if softening occurs. Low strain amplitude cyclic deformation is understood in terms of dislocation loop patch and persistent slip band behavior, high strain deformation in terms of dislocation cell-shuttling models. While interesting advances in these fields have been made in the last few years, the deformation mechanisms are generally poorly understood

Tephras in lacustrine sediments of the Sarliève marsh (French Massif Central): age and preservation

Science.gov (United States)

Fourmont, Agathe; Macaire, Jean-Jacques; Bréhéret, Jean-Gabriel; Argant, Jacqueline; Prat, Béatrice; Vernet, Gérard

2006-12-01

The Sarliève marsh sediments (Massif Central, France) contain two tephras. The first tephra [ 13.7±0.4ka(2δ), ca. 12 000 BP], regionally well known, enables to date the beginning of lacustrine infill to the Lateglacial. The second tephra, the 'tephra de Sarliève', the emitting volcano of which is unknown, would be dated to around the Early Subboreal from pollen data. This occurrence, after the discovery of the 'tephra de Beaunit', emphasizes that volcanic eruption(s) occurred in the 'Chaîne des Puys' or in the volcanic Cézallier more than 1000 years after the last known eruption (Pavin) in the 'Chaîne des Puys' at around 6.6/6.7 ka (5800/5900 BP). In the Sarliève piles, these tephras, well preserved in thick and more silicated deposits of deltas, were not observed in carbonated basin sediments where they were altered. The abundance of authigenic zeolites formed during the Lateglacial in restricted depocentre lacustrine waters allows us to detect initial CF1 tephra occurrence. To cite this article: A. Fourmont et al., C. R. Geoscience 338 (2006).

Cyclic AMP in rat pancreatic islets

International Nuclear Information System (INIS)

Grill, V.; Borglund, E.; Cerasi, E.; Uppsala Univ.

1977-01-01

The incorporation of [ 3 H]adenine into cyclic AMP was studied in rat pancreatic islets under varying conditions of labeling. Prolonging the exposure to [ 3 H]adenine progressively augmented the islet cyclic [ 3 H]AMP level. Islets labeled for different periods of time and subsequently incubated (without adenine) in the presence of D-glucose or cholera toxin showed stimulations of intra-islet cyclic [ 3 H]AMP that were proportionate to the levels of radioactive nucleotide present under non-stimulatory conditions. Labeling the islets in a high glucose concentration (27.7 mM) did not modify the nucleotide responses to glucose or cholera toxin. The specific activity of cyclic [ 3 H]AMP, determined by simultaneous assay of cyclic [ 3 H]AMP and total cyclic AMP, was not influenced by glucose or cholera toxin. Glucose had no effect on the specific activity of labeled ATP

Lower fecundity in parthenogenetic geckos than sexual relatives in the Australian arid zone.

Science.gov (United States)

Kearney, M; Shine, R

2005-05-01

Theoretical models of the advantage of sexual reproduction typically assume that reproductive output is equal in sexual and parthenogenetic females. We tested this assumption by comparing fecundity between parthenogenetic and sexual races of gekkonid lizards in the Heteronotia binoei complex, collected across a 1200 km latitudinal gradient through the Australian arid zone. Under laboratory conditions, parthenogenetic geckos had approximately 30% lower fecundity when compared with their sexual progenitors, irrespective of body size. Reflecting clutch-size constraints in gekkonids, this fecundity difference was mainly because of fewer clutches over a shorter period. When parthenogens were compared more broadly with all coexisting sexual races across the latitudinal gradient, parthenogens had lower fecundity than sexuals only when corrected for body size. Differences in fecundity between parthenogens and coexisting sexual races depended on which sexual race was considered. There was no significant relationship between fecundity and parasite (mite) load, despite significantly higher mite loads in parthenogens than in sexual races.

Disentangling natural and anthropogenic signals in lacustrine records: An example from the Ilan Plain, NE Taiwan

Directory of Open Access Journals (Sweden)

Jyh-Jaan Huang

2016-11-01

Full Text Available The impact of human activities has been increasing to a degree where humans now outcompete many natural processes. When interpreting environmental and climatic changes recorded in natural archives on historical time scales, it is therefore important to be able to disentangle the relative contribution of natural and anthropogenic processes. Lake Meihua on the Ilan Plain in northeastern Taiwan offers a particularly suitable opportunity to test how human activities known from historical records can be recorded in lacustrine sediment. For this purpose, three cores from Lake Meihua have been studied by a multiproxy approach, providing the first decadal-resolution lacustrine records covering the past 150 years in Taiwan. Profiles of excess 210Pb, 137Cs and 239,240Pu from two short cores (MHL-09-01 and MHL-11-02 allowed a precise chronology to be established. The presence of a yellow, earthy layer with lower levels of organic material coincide with the record of land development associated with the construction of the San-Chin-Gong Temple during AD 1970-1982. Furthermore, in the lower part of the cores, the upwards increasing trend of inc/coh, TOC, TOC/TN, and grain size, coupled with the palynological data (increase of Alnus, Mallotus, Trema and herbs from the nearby core MHL-5A with radiocarbon chronology, suggest that the area surrounding the lake has been significantly affected by agricultural activities since the arrival of Chinese settlers around ~AD 1874. In sum, this study demonstrates that this suite of lacustrine sediments in northeastern Taiwan has recorded human activities in agreement with historical documents, and that different human activities will leave distinct sedimentological, geochemical, and palynological signatures in the sedimentary archives. Therefore, multiproxy reconstructions are important to capture the complex nature of human-environmental interactions. A better understanding of the weathering and erosion response to human

Disentangling natural and anthropogenic signals in lacustrine records: An example from the Ilan Plain, NE Taiwan

Science.gov (United States)

Huang, Jyh-Jaan; Huh, Chih-An; Wei, Kuo-Yen; Löwemark, Ludvig; Lin, Shu-Fen; Liao, Wen-Hsuan; Yang, Tien-Nan; Song, Sheng-Rong; Lee, Meng-Yang; Su, Chih-Chieh; Lee, Teh-Quei

2016-11-01

The impact of human activities has been increasing to a degree where humans now outcompete many natural processes. When interpreting environmental and climatic changes recorded in natural archives on historical time scales, it is therefore important to be able to disentangle the relative contribution of natural and anthropogenic processes. Lake Meihua on the Ilan Plain in northeastern Taiwan offers a particularly suitable opportunity to test how human activities known from historical records can be recorded in lacustrine sediment. For this purpose, three cores from Lake Meihua have been studied by a multiproxy approach, providing the first decadal-resolution lacustrine records covering the past 150 years in Taiwan. Profiles of excess 210Pb, 137Cs and 239,240Pu from two short cores (MHL-09-01 and MHL-11-02) allowed a precise chronology to be established. The presence of a yellow, earthy layer with lower levels of organic material coincide with the record of land development associated with the construction of the San-Chin-Gong Temple during AD 1970-1982. Furthermore, in the lower part of the cores, the upwards increasing trend of inc/coh, TOC, TOC/TN, and grain size, coupled with the palynological data (increase of Alnus, Mallotus, Trema and herbs) from the nearby core MHL-5A with radiocarbon chronology, suggest that the area surrounding the lake has been significantly affected by agricultural activities since the arrival of Chinese settlers around AD 1874. In sum, this study demonstrates that this suite of lacustrine sediments in northeastern Taiwan has recorded human activities in agreement with historical documents, and that different human activities will leave distinct sedimentological, geochemical, and palynological signatures in the sedimentary archives. Therefore, multiproxy reconstructions are important to capture the complex nature of human-environmental interactions. A better understanding of the weathering and erosion response to human activities can

The relationship between humans and climate across the North Atlantic: what can lacustrine biomarkers tell us?

Science.gov (United States)

de Wet, G.; Castañeda, I. S.; Bradley, R. S.; Small, G.; Barrasso, T.

2016-12-01

While climate change has been implicated in the colonization/population dynamics of the North Atlantic region, researchers in many cases are forced to compare archaeological data with distant paleoclimate records, making these linkages tenuous. Our research utilizes novel organic biomarkers in lacustrine sediments to produce paired paleoclimate and human occupancy reconstructions to better address questions surrounding human migration and climate change. Here we present preliminary results from two prominent locations in the history of the European colonization of the North Atlantic. The first, carried out on the Norse "Eastern Settlement" in Southern Greenland, attempts to answer the long-standing question of whether climate change caused the demise of the colony in the 1400s C.E. Second, we use similar techniques to search for evidence of the first peopling of the Faroe Islands, a highly debated topic. The use of lacustrine biomarkers allows for numerous aspects of both paleoclimate and human presence in a catchment to be reconstructed. We reconstruct paleotemperatures using branched glycerol dialkyl glycerol tetraethers (brGDGTs) and alkenones (the UK37 Index), when present. Additionally, will analyze the difference in the hydrogen isotopic composition of long and short-chain plant leaf waxes as a proxy for lake water balance. Human occupancy in the region is investigated using fecal sterols and stanols, primarily created by the breakdown of cholesterol. Some of these compounds, such as coprostanol (the dominant sterol in human waste), provide strong evidence of human settlements and have been identified in some of our lake records. Our preliminary results suggest that temperatures were increasing in SW Greenland during the period when the Norse are thought to have died out, potentially challenging the long-standing view of climate deterioration being the primary cause of their demise. Primary productivity biomarkers from lake Eidisvatnet, in the Faroe Islands

Cyclic peptide therapeutics: past, present and future.

Science.gov (United States)

Zorzi, Alessandro; Deyle, Kaycie; Heinis, Christian

2017-06-01

Cyclic peptides combine several favorable properties such as good binding affinity, target selectivity and low toxicity that make them an attractive modality for the development of therapeutics. Over 40 cyclic peptide drugs are currently in clinical use and around one new cyclic peptide drug enters the market every year on average. The vast majority of clinically approved cyclic peptides are derived from natural products, such as antimicrobials or human peptide hormones. New powerful techniques based on rational design and in vitro evolution have enabled the de novo development of cyclic peptide ligands to targets for which nature does not offer solutions. A look at the cyclic peptides currently under clinical evaluation shows that several have been developed using such techniques. This new source for cyclic peptide ligands introduces a freshness to the field, and it is likely that de novo developed cyclic peptides will be in clinical use in the near future. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sequencing Cyclic Peptides by Multistage Mass Spectrometry

Science.gov (United States)

Mohimani, Hosein; Yang, Yu-Liang; Liu, Wei-Ting; Hsieh, Pei-Wen; Dorrestein, Pieter C.; Pevzner, Pavel A.

2012-01-01

Some of the most effective antibiotics (e.g., Vancomycin and Daptomycin) are cyclic peptides produced by non-ribosomal biosynthetic pathways. While hundreds of biomedically important cyclic peptides have been sequenced, the computational techniques for sequencing cyclic peptides are still in their infancy. Previous methods for sequencing peptide antibiotics and other cyclic peptides are based on Nuclear Magnetic Resonance spectroscopy, and require large amount (miligrams) of purified materials that, for most compounds, are not possible to obtain. Recently, development of mass spectrometry based methods has provided some hope for accurate sequencing of cyclic peptides using picograms of materials. In this paper we develop a method for sequencing of cyclic peptides by multistage mass spectrometry, and show its advantages over single stage mass spectrometry. The method is tested on known and new cyclic peptides from Bacillus brevis, Dianthus superbus and Streptomyces griseus, as well as a new family of cyclic peptides produced by marine bacteria. PMID:21751357

The calculation of dissipated work, elastoplastic cyclic stress and cyclic strain in a structure

International Nuclear Information System (INIS)

Wang Xucheng; Xie Yihuan.

1986-01-01

With the development of the reactor technique, there is being an increasing interest in the calculation of elastoplastic response of a structure to its complex loading. This paper introduces a constitutive relation of a material for discribing unloading property, and uses it in an analysis of a real structure under a cyclic loading. The results, which include cyclic stress, cyclic strain and dissipated work, are meaningful in the researches of the structure behavior under complex loading and of the structural safety

Regional chemostratigraphic key horizons in the macrofossil-barren siliciclastic lower Miocene lacustrine sediments (Most Basin, Eger Graben, Czech Republic)

Czech Academy of Sciences Publication Activity Database

Matys Grygar, Tomáš; Mach, K.

2013-01-01

Roč. 88, č. 3 (2013), s. 557-571 ISSN 1214-1119 R&D Projects: GA ČR(CZ) GAP210/11/1357 Institutional support: RVO:61388980 Keywords : Most Basin * Burdigalian * chemostratigraphy * proxy analyses * lacustrine sediments Subject RIV: DD - Geochemistry Impact factor: 1.495, year: 2013

Sedimentological reservoir characteristics of the Paleocene fluvial/lacustrine Yabus Sandstone, Melut Basin, Sudan

Science.gov (United States)

Mahgoub, M. I.; Padmanabhan, E.; Abdullatif, O. M.

2016-11-01

Melut Basin in Sudan is regionally linked to the Mesozoic-Cenozoic Central and Western African Rift System (CWARS). The Paleocene Yabus Formation is the main oil producing reservoir in the basin. It is dominated by channel sandstone and shales deposited in fluvial/lacustrine environment during the third phase of rifting in the basin. Different scales of sedimentological heterogeneities influenced reservoir quality and architecture. The cores and well logs analyses revealed seven lithofacies representing fluvial, deltaic and lacustrine depositional environments. The sandstone is medium to coarse-grained, poorly to moderately-sorted and sub-angular to sub-rounded, arkosic-subarkosic to sublitharenite. On the basin scale, the Yabus Formation showed variation in sandstone bodies, thickness, geometry and architecture. On macro-scale, reservoir quality varies vertically and laterally within Yabus Sandstone where it shows progressive fining upward tendencies with different degrees of connectivity. The lower part of the reservoir showed well-connected and amalgamated sandstone bodies, the middle to the upper parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenetic changes such as compaction, cementation, alteration, dissolution and kaolinite clays pore fill and coat all have significantly reduced the reservoir porosity and permeability. The estimated porosity in Yabus Formation ranges from 2 to 20% with an average of 12%; while permeability varies from 200 to 500 mD and up to 1 Darcy. The understanding of different scales of sedimentological reservoir heterogeneities might contribute to better reservoir quality prediction, architecture, consequently enhancing development and productivity.

Development and Rainfed Paddy Soils Potency Derived from Lacustrine Material in Paguyaman, Gorontalo

Directory of Open Access Journals (Sweden)

Nurdin

2011-09-01

Full Text Available Rainfed paddy soils that are derived from lacustrine and include of E4 agroclimatic zone have many unique properties and potentially for paddy and corn plantations. This sreseach was aimed to: (1 study the soil development of rainfed paddy soils derived from lacustrine and (2 evaluate rainfed paddy soils potency for paddy and corn in Paguyaman. Soil samples were taken from three profiles according to toposequent, and they were analyzed in laboratory. Data were analyzed with descriptive-quantitative analysis. Furthermore, assessment on rainfed paddy soils potency was conducted with land suitability analysis using parametric approach. Results indicate that all pedon had evolved with B horizons structurization. However, pedon located on the summit slope was more developed and intensely weathered than those of the shoulder and foot slopes.The main pedogenesis in all pedons were through elluviation, illuviation, lessivage, pedoturbation, and gleization processes. The main factors of pedogenesis were climate, age (time and topography factors. Therefore, P1 pedons are classified as Ustic Endoaquerts, fine, smectitic, isohypertermic; P2 as Vertic Endoaquepts, fine, smectitic, isohypertermic; and P3 as Vertic Epiaquepts, fine, smectitic, isohypertermic. Based on the potentials of the land, the highest of land suitability class (LSC of land utilization type (LUT local paddy was highly suitable (S1, while the lowest one was not suitable with nutrient availability as the limiting factor (Nna. The highest LCS of paddy-corn LUT was marginally suitable with water availability as the limiting factor (S3wa, while the lower LSC was not suitable with nutrient availabily as the limiting factor (Nna.

Predominance of even carbon-numbered n-alkanes from lacustrine sediments in Linxia Basin, NE Tibetan Plateau: Implications for climate change

Energy Technology Data Exchange (ETDEWEB)

Wang Yongli [Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics, Chinese Academy of Sciences, Lanzhou 730000 (China)] [Institute of Tibetan and Plateau Research, Chinese Academy of Sciences, Beijing 100085 (China); Fang Xiaomin, E-mail: fangxm@itpcas.ac.cn [Institute of Tibetan and Plateau Research, Chinese Academy of Sciences, Beijing 100085 (China)] [Key Laboratory of Western Resources and Environment of Education Ministry, College at Earth and Environment Sciences, University of Lanzhou, Lanzhou 730000 (China); Zhang Tongwei [Key Laboratory of Western Resources and Environment of Education Ministry, College at Earth and Environment Sciences, University of Lanzhou, Lanzhou 730000 (China); Li Yuanmao; Wu Yingqin; He Daxiang; Wang Youxiao [Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics, Chinese Academy of Sciences, Lanzhou 730000 (China)

2010-10-15

Research highlights: {yields} This study reports the first observation of predominant even carbon-numbered n-alkanes of sediments in the continuous lacustrine-sedimentary section (Maogou) from the Late Miocene to the Early Pliocene (13-4.4 Ma) in the Linxia Basin, NE Tibetan Plateau. {yields} Certain types of special autochthonous bacteria are a possible source for the special distribution of even carbon-numbered n-alkanes in lacustrine sediments. {yields} These bacteria may have a high production rate in weak oxic-anoxic and arid depositional environments, in which a variety of geochemical parameters have recorded palaeoclimate change. {yields} A close correspondence among the low ratio of n-C{sub 27}/n-C{sub 31}, the heavy {delta}{sup 13}C values of TOC and a strong even carbon-number predominance (low OEP{sub 16-20} values) from approximately 6.5 to 4.4 Ma and at approximately 8 Ma in the studied section suggests that n-alkanes with a high predominance of even carbon-numbers may be treated as geochemical proxies for arid climate. - Abstract: This study reports the first observation of predominant even C-numbered n-alkanes from sediments in the continuous lacustrine-sedimentary section (Maogou) from the Late Miocene to the Early Pliocene (13-4.4 Ma) in the Linxia Basin, NE Tibetan Plateau. The n-alkanes showed a bimodal distribution that is characterised by a centre at n-C{sub 16}-n-C{sub 20} with maximum values at n-C{sub 18} and n-C{sub 27}-n-C{sub 31} as well as at n-C{sub 29}. The first mode shows a strong even C-number predominance (OEP{sub 16-20} 0.34-0.66). In contrast, the second mode has a strong odd C-number predominance (OEP{sub 27-31} 1.20-2.45). Certain types of special autochthonous bacteria are a possible source for this distribution of even C-numbered n-alkanes in lacustrine sediments. These bacteria may have a high production rate in weak oxic-anoxic and arid depositional environments, in which a variety of geochemical parameters have recorded

The arabidopsis cyclic nucleotide interactome

KAUST Repository

Donaldson, Lara Elizabeth; Meier, Stuart Kurt; Gehring, Christoph A

2016-01-01

Cyclic nucleotides have been shown to play important signaling roles in many physiological processes in plants including photosynthesis and defence. Despite this, little is known about cyclic nucleotide-dependent signaling mechanisms

Volcanic influence of Mt. Fuji on the watershed of Lake Motosu and its impact on the lacustrine sedimentary record

Science.gov (United States)

Lamair, Laura; Hubert-Ferrari, Aurélia; Yamamoto, Shinya; El Ouahabi, Meriam; Vander Auwera, Jacqueline; Obrochta, Stephen; Boes, Evelien; Nakamura, Atsunori; Fujiwara, Osamu; Shishikura, Masanobu; Schmidt, Sabine; Siani, Giuseppe; Miyairi, Yosuke; Yokoyama, Yusuke; De Batist, Marc; Heyvaert, Vanessa M. A.; QuakeRecNankai Team

2018-01-01

Lacustrine sediments are particularly sensitive to modifications within the lake catchment. In a volcanic area, sedimentation rates are directly affected by the history of the volcano and its eruptions. Here, we investigate the impact of Mt. Fuji Volcano (Japan) on Lake Motosu and its watershed. The lacustrine infill is studied by combining seismic reflection profiles and sediment cores. We show evidence of changes in sedimentation patterns during the depositional history of Lake Motosu. The frequency of large mass-transport deposits recorded within the lake decreases over the Holocene. Before 8000 cal yr BP, large sublacustrine landslides and turbidites were filling the lacustrine depression. After 8000 cal yr BP, only one large sublacustrine landslide was recorded. The change in sedimentation pattern coincides with a change in sediment accumulation rate. Over the last 8000 cal yr BP, the sediment accumulation rate was not sufficient enough to produce large sublacustrine slope failures. Consequently, the frequency of large mass-transport deposits decreased and only turbidites resulting from surficial slope reworking occurred. These constitute the main sedimentary infill of the deep basin. We link the change in sediment accumulation rate with (i) climate and vegetation changes; and (ii) the Mt. Fuji eruptions which affected the Lake Motosu watershed by reducing its size and strongly modified its topography. Moreover, this study highlights that the deposition of turbidites in the deep basin of Lake Motosu is mainly controlled by the paleobathymetry of the lakefloor. Two large mass-transport deposits, occurring around 8000 cal yr BP and 2000 cal yr BP respectively, modified the paleobathymetry of the lakefloor and therefore changed the turbidite depositional pattern of Lake Motosu.

40 CFR 721.2120 - Cyclic amide.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Cyclic amide. 721.2120 Section 721... Cyclic amide. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as a cyclic amide (PMN P-92-131) is subject to reporting under this section for the...

An Investigation of Trace Elements in Marine and Lacustrine Deposits by Means of a Neutron Activation Method

Energy Technology Data Exchange (ETDEWEB)

Landstroem, O; Samsahl, K; Wenner, C G

1967-10-15

A neutron activation method for multi-elemental analysis was applied to argillaceous deposits from the Viskan Valley on the Swedish West Coast, an area in which transgressions and regressions of the sea have occurred during the postglacial time. These changes between fresh-water and marine stages are well known from earlier geologic investigations. Analysis could therefore be performed of samples of known marine (brackish) and lacustrine origin. In a preliminary test on four samples, taken from two marine layers and two lacustrine layers, altogether 30 elements were quantitatively determined, namely As, Br, Ca, Ce, Co, Cr, Cs, Eu, Fe, Ga, Hf, Hg, La, Lu, Mn, Na, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, U, W, Yb, Zn and Zr. Several elements showed a difference in concentration between the marine and the fresh-water layers. Br, Hg, Mn, Se, As and Sb were more thoroughly investigated in three boreholes from different sections of the valley. Br and Se had high means in the most pronounced marine samples of the fiord deposits. Moreover, Mn showed a fourfold increase just in the transition stage between the older sea fiord and the older lage stage.

An Investigation of Trace Elements in Marine and Lacustrine Deposits by Means of a Neutron Activation Method

International Nuclear Information System (INIS)

Landstroem, O.; Samsahl, K.; Wenner, C.G.

1967-10-01

A neutron activation method for multi-elemental analysis was applied to argillaceous deposits from the Viskan Valley on the Swedish West Coast, an area in which transgressions and regressions of the sea have occurred during the postglacial time. These changes between fresh-water and marine stages are well known from earlier geologic investigations. Analysis could therefore be performed of samples of known marine (brackish) and lacustrine origin. In a preliminary test on four samples, taken from two marine layers and two lacustrine layers, altogether 30 elements were quantitatively determined, namely As, Br, Ca, Ce, Co, Cr, Cs, Eu, Fe, Ga, Hf, Hg, La, Lu, Mn, Na, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, U, W, Yb, Zn and Zr. Several elements showed a difference in concentration between the marine and the fresh-water layers. Br, Hg, Mn, Se, As and Sb were more thoroughly investigated in three boreholes from different sections of the valley. Br and Se had high means in the most pronounced marine samples of the fiord deposits. Moreover, Mn showed a fourfold increase just in the transition stage between the older sea fiord and the older lage stage

Detection of Cyclic Dinucleotides by STING.

Science.gov (United States)

Du, Xiao-Xia; Su, Xiao-Dong

2017-01-01

STING (stimulator of interferon genes) is an essential signaling adaptor protein mediating cytosolic DNA-induced innate immunity for both microbial invasion and self-DNA leakage. STING is also a direct receptor for cytosolic cyclic dinucleotides (CDNs), including the microbial secondary messengers c-di-GMP (3',3'-cyclic di-GMP), 3',3'cGAMP (3',3'-cyclic GMP-AMP), and mammalian endogenous 2',3'cGAMP (2',3'-cyclic GMP-AMP) synthesized by cGAS (cyclic GMP-AMP synthase). Upon CDN binding, STING undergoes a conformational change to enable signal transduction by phosphorylation and finally to active IRF3 (Interferon regulatory factor 3) for type I interferon production. Here, we describe some experimental procedures such as Isothermal Titration Calorimetry and luciferase reporter assays to study the CDNs binding and activity by STING proteins.

Cyclic completion of the anamorphic universe

Science.gov (United States)

Ijjas, Anna

2018-04-01

Cyclic models of the universe have the advantage of avoiding initial conditions problems related to postulating any sort of beginning in time. To date, the best known viable examples of cyclic models have been ekpyrotic. In this paper, we show that the recently proposed anamorphic scenario can also be made cyclic. The key to the cyclic completion is a classically stable, non-singular bounce. Remarkably, even though the bounce construction was originally developed to connect a period of contraction with a period of expansion both described by Einstein gravity, we show here that it can naturally be modified to connect an ordinary contracting phase described by Einstein gravity with a phase of anamorphic smoothing. The paper will present the basic principles and steps in constructing cyclic anamorphic models.

Lacustrine wetland in an agricultural catchment: nitrogen removal and related biogeochemical processes

Directory of Open Access Journals (Sweden)

R. Balestrini

2008-03-01

Full Text Available The role of specific catchment areas, such as the soil-river or lake interfaces, in removing or buffering the flux of N from terrestrial to aquatic ecosystems is globally recognized but the extreme variability of microbiological and hydrological processes make it difficult to predict the extent to which different wetlands function as buffer systems. In this paper we evaluate the degree to which biogeochemical processes in a lacustrine wetland are responsible for the nitrate removal from ground waters feeding Candia Lake (Northern Italy. A transect of 18 piezometers was installed perpendicular to the shoreline, in a sub-unit formed by 80 m of poplar plantation, close to a crop field and 30 m of reed swamp. The chemical analysis revealed a drastic NO₃^–-N ground water depletion from the crop field to the lake, with concentrations decreasing from 15–18 mg N/l to the detection limit within the reeds. Patterns of Cl^–, SO₄^2–, O₂, NO₂^–-N, HCO₃^– and DOC suggest that the metabolic activity of bacterial communities, based on the differential use of electron donors and acceptors in redox reactions is the key function of this system. The significant inverse relationship found between NO₃^–-N and HCO₃^– is a valuable indicator of the denitrification activity. The pluviometric regime, the temperature, the organic carbon availability and the hydrogeomorphic properties are the main environmental factors affecting the N transformations in the studied lacustrine ecosystem.

Adenosine 3':5'-cyclic monophosphate in higher plants: Isolation and characterization of adenosine 3':5'-cyclic monophosphate from Kalanchoe and Agave.

Science.gov (United States)

Ashton, A R; Polya, G M

1977-01-01

1.3':5'-Cyclic AMP was extensively purified from Kalanchoe daigremontiana and Agave americana by neutral alumina and anion- and cation-exchange column chromatography. Inclusion of 3':5'-cyclic [8-3H]AMP from the point of tissue extraction permitted calculation of yields. The purification procedure removed contaminating material that was shown to interfere with the 3':5'-cyclic AMP estimation and characterization procedures. 2. The partially purified 3':5'-cyclic AMP was quantified by means of a radiochemical saturation assay using an ox heart 3':5'-cyclic AMP-binding protein and by an assay involving activation of a mammalian protein kinase. 3. The plant 3':5'-cyclic AMP co-migrated with 3':5'-cyclic [8-3H]AMP on cellulose chromatography, poly(ethyleneimine)-cellulose chromatography and silica-gel t.l.c. developed with several solvent systems. 4. The plant 3':5'-cyclic AMP was degraded by ox heart 3':5'-cyclic nucleotide phosphodiesterase at the same rates as authentic 3':5'-cyclic AMP. 1-Methyl-3-isobutylxanthine (1 mM), a specific inhibitor of the 3':5'-cyclic nucleotide phosphodieterase, completely inhibited such degradation. 5. The concentrations of 3':5'-cyclic AMP satisfying the above criteria in Kalanchoe and Agave were 2-6 and 1 pmol/g fresh wt. respectively. Possible bacterial contribution to these analyses was estimated to be less than 0.002pmol/g fresh wt. Evidence for the occurrence of 3':5'-cyclic AMP in plants is discussed. PMID:196595

History-independent cyclic response of nanotwinned metals

Science.gov (United States)

Pan, Qingsong; Zhou, Haofei; Lu, Qiuhong; Gao, Huajian; Lu, Lei

2017-11-01

Nearly 90 per cent of service failures of metallic components and structures are caused by fatigue at cyclic stress amplitudes much lower than the tensile strength of the materials involved. Metals typically suffer from large amounts of cumulative, irreversible damage to microstructure during cyclic deformation, leading to cyclic responses that are unstable (hardening or softening) and history-dependent. Existing rules for fatigue life prediction, such as the linear cumulative damage rule, cannot account for the effect of loading history, and engineering components are often loaded by complex cyclic stresses with variable amplitudes, mean values and frequencies, such as aircraft wings in turbulent air. It is therefore usually extremely challenging to predict cyclic behaviour and fatigue life under a realistic load spectrum. Here, through both atomistic simulations and variable-strain-amplitude cyclic loading experiments at stress amplitudes lower than the tensile strength of the metal, we report a history-independent and stable cyclic response in bulk copper samples that contain highly oriented nanoscale twins. We demonstrate that this unusual cyclic behaviour is governed by a type of correlated ‘necklace’ dislocation consisting of multiple short component dislocations in adjacent twins, connected like the links of a necklace. Such dislocations are formed in the highly oriented nanotwinned structure under cyclic loading and help to maintain the stability of twin boundaries and the reversible damage, provided that the nanotwins are tilted within about 15 degrees of the loading axis. This cyclic deformation mechanism is distinct from the conventional strain localizing mechanisms associated with irreversible microstructural damage in single-crystal, coarse-grained, ultrafine-grained and nanograined metals.

Cyclical subnormal separation in A-groups

International Nuclear Information System (INIS)

Makarfi, M.U.

1995-12-01

Three main results, concerning A-groups in respect of cyclical subnormal separation as defined in, are presented. It is shown in theorem A that any A-group that is generated by elements of prime order and satisfying the cyclical subnormal separation conditions is metabelian. The two other main results give necessary and sufficient conditions for A-groups, that are split extensions of certain abelian p-groups by a metabelian p'-group, to satisfy the cyclical subnormal separation condition. There is also a result which shows that A-groups with elementary abelian Sylow subgroups are cyclically separated as defined. (author). 7 refs

Greigite formed in early Pleistocene lacustrine sediments from the Heqing Basin, southwest China, and its paleoenvironmental implications

Science.gov (United States)

Qiang, Xiaoke; Xu, Xinwen; Zhao, Hui; Fu, Chaofeng

2018-05-01

The ferrimagnetic iron sulfide greigite (Fe3S4) occurs widely in sulfidic lacustrine and marine sedimentary environments. Knowledge of its formation and persistence is important for both magnetostratigraphic and paleoenvironmental studies. Although the formation mechanism of greigite has been widely demonstrated, the sedimentary environments associated with greigite formation in lakes, especially on relatively long timescales, are poorly understood. A long and continuous sequence of Pleistocene lacustrine sediments was recovered in the Heqing drill core from southwestern China, which provides an outstanding record of continental climate and environment. Integrated magnetic, geochemical, and paleoclimatic analysis of the lacustrine sequence provides an opportunity to improve our understanding of the environmental controls on greigite formation. Rock magnetic and scanning electron microscope analyses of selected samples from the core reveal that greigite is present in the lower part of the core (part 1, 665.8-372.5 m). Greigite occurs throughout this interval and is the dominant magnetic mineral, irrespective of the climatic state. The magnetic susceptibility (χ) record, which is mainly controlled by the concentration of greigite, matches well with variations in the Indian Summer Monsoon (ISM) index and total organic carbon (TOC) content, with no significant time lag. This indicates that the greigite formed during early diagenesis. In greigite-bearing intervals, with the χ increase, Bc value increase and tends to be stable at about 50 mT. Therefore, we suggest that χ values could estimate the variation of greigite concentration approximately in the Heqing core. Greigite favored more abundant in terrigenous-rich and organic-poor layers associated with weak summer monsoon which are characterized by high χ values, high Fe content, high Rb/Sr ratio and low TOC content. Greigite enhancement can be explained by variations in terrigenous inputs. Our studies demonstrate

Lacustrine Records of Holocene Mountain Glacier Fluctuations from Western Greenland

Science.gov (United States)

Schweinsberg, A.; Briner, J. P.; Bennike, O.

2014-12-01

Recent studies have focused on documenting fluctuations of the Greenland Ice Sheet margin throughout the Holocene but few data exist that constrain past changes of local glaciers independent of the ice sheet. Our research combines proglacial lake sediment analysis with cosmogenic 10Be dating of Holocene moraines and radiocarbon dating of ice-cap-killed vegetation with an overall objective to use this multi-proxy approach to generate a detailed record of the coupled climate-glacier system through the Holocene. Here, we present lacustrine records of mountain glacier variability from continuous pro-glacial lake sediment sequences recovered from two glaciated catchments in northeastern Nuussuaq, western Greenland. We use radiocarbon-dated sediments from Sikuiui and Pauiaivik lakes to reconstruct the timing of advance and retreat of local glaciers. Sediments were characterized with magnetic susceptibility (MS), gamma density, Itrax XRF and visible reflectance spectroscopy at 0.2 cm intervals and sediment organic matter at 0.5 cm intervals. Basal radiocarbon ages provide minimum-age constraints on deglaciation from Sikuiui and Pauiaivik lakes of ~9.6 and 8.7 ka, respectively. Organic-rich gyttja from deglaciation until ~5.0 ka in Pauiaivik Lake suggests minimal glacial extent there while slightly elevated MS values from ~9.0 - 7.0 ka in Sikuiui Lake may reflect early Holocene glacial advances. Minerogenic sediment input gradually increases starting at ~5.0 ka in Pauiaivik Lake, which we interpret as the onset of Neoglaciation in the catchment. Furthermore, a distinct episode of enhanced glacial activity from ~4.0 - 2.2 ka in Sikuiui Lake may be correlative to a period of persistent snowline lowering evidenced by radiocarbon dates of ice-killed vegetation from nearby ice cap margins. Results from these lacustrine records and our ice-killed vegetation dataset suggest a middle Holocene onset of Neoglaciation ~5.0 - 4.0 ka in this region. We are supplementing these records

Phylogeography of competing sexual and parthenogenetic forms of a freshwater flatworm: patterns and explanations

Directory of Open Access Journals (Sweden)

Carranza Salvador

2003-11-01

Full Text Available Abstract Background Models of the maintenance of sex predict that one reproductive strategy, sexual or parthenogenetic, should outcompete the other. Distribution patterns may reflect the outcome of this competition as well as the effect of chance and historical events. We review the distribution data of sexual and parthenogenetic biotypes of the planarian Schmidtea polychroa. Results S. polychroa lives in allopatry or sympatry across Europe except for Central and North-Western Europe, where sexual individuals have never been reported. A phylogenetic relationship between 36 populations based on a 385 bp fragment of the mitochondrial cytochrome oxidase I gene revealed that haplotypes were often similar over large geographic distances. In North Italian lakes, however, diversity was extreme, with sequence differences of up to 5% within the same lake in both sexuals and parthenogens. Mixed populations showed "endemic" parthenogenetic lineages that presumably originated from coexisting sexuals, and distantly related ones that probably result from colonization by parthenogens independent from sexuals. Conclusions Parthenogens originated repeatedly from sexuals, mainly in Italy, but the same may apply to other Mediterranean regions (Spain, Greece. The degree of divergence between populations suggests that S. polychroa survived the ice ages in separate ice-free areas in Central, Eastern and Southern Europe and re-colonised Europe after the retreat of the major glaciers. Combining these results with those based on nuclear markers, the data suggest that repeated hybridisation between sexuals and parthenogenetic lineages in mixed populations maintains high levels of genetic diversity in parthenogens. This can explain why parthenogens persist in populations that were originally sexual. Exclusive parthenogenesis in central and western populations suggests better colonisation capacity, possibly because of inbreeding costs as well as hybridisation of sexuals

Cyclic characteristics of earthquake time histories

International Nuclear Information System (INIS)

Hall, J.R. Jr; Shukla, D.K.; Kissenpfennig, J.F.

1977-01-01

From an engineering standpoint, an earthquake record may be characterized by a number of parameters, one of which is its 'cyclic characteristics'. The cyclic characteristics are most significant in fatigue analysis of structures and liquefaction analysis of soils where, in addition to the peak motion, cyclic buildup is significant. Whereas duration peak amplitude and response spectra for earthquakes have been studied extensively, the cyclic characteristics of earthquake records have not received an equivalent attention. Present procedures to define the cyclic characteristics are generally based upon counting the number of peaks at various amplitude ranges on a record. This paper presents a computer approach which describes a time history by an amplitude envelope and a phase curve. Using Fast Fourier Transform Techniques, an earthquake time history is represented as a projection along the x-axis of a rotating vector-the length the vector is given by the amplitude spectra-and the angle between the vector and x-axis is given by the phase curve. Thus one cycle is completed when the vector makes a full rotation. Based upon Miner's cumulative damage concept, the computer code automatically combines the cycles of various amplitudes to obtain the equivalent number of cycles of a given amplitude. To illustrate the overall results, the cyclic characteristics of several real and synthetic earthquake time histories have been studied and are presented in the paper, with the conclusion that this procedure provides a physical interpretation of the cyclic characteristics of earthquakes. (Auth.)

Monopod bucket foundations under cyclic lateral loading

DEFF Research Database (Denmark)

Foglia, Aligi; Ibsen, Lars Bo

on bucket foundations under lateral cyclic loading. The test setup is described in detail and a comprehensive experimental campaign is presented. The foundation is subjected to cyclic overturning moment, cyclic horizontal loading and constant vertical loading, acting on the same plane for thousands...

Geochemical characteristics of Tertiary saline lacustrine oils in the Western Qaidam Basin, northwest China

International Nuclear Information System (INIS)

Zhu Yangming; Weng Huanxin; Su Aiguo; Liang Digang; Peng Dehua

2005-01-01

Based on the systematic analyses of light hydrocarbon, saturate, aromatic fractions and C isotopes of over 40 oil samples along with related Tertiary source rocks collected from the western Qaidam basin, the geochemical characteristics of the Tertiary saline lacustrine oils in this region was investigated. The oils are characterized by bimodal n-alkane distributions with odd-to-even (C 11 -C 17 ) and even-to-odd (C 18 -C 28 ) predominance, low Pr/Ph (mostly lower than 0.6), high concentration of gammacerane, C 35 hopane and methylated MTTCs, reflecting the high salinity and anoxic setting typical of a saline lacustrine depositional environment. Mango's K 1 values in the saline oils are highly variable (0.99-1.63), and could be associated with the facies-dependent parameters such as Pr/Ph and gammacerane indexes. Compared with other Tertiary oils, the studied Tertiary saline oils are marked by enhanced C 28 sterane abundance (30% or more of C 27 -C 29 homologues), possibly derived from halophilic algae. It is noted that the geochemical parameters of the oils in various oilfields exhibit regular spatial changes, which are consistent with the depositional phase variations of the source rocks. The oils have uncommon heavy C isotopic ratios (-24%o to -26%o) and a flat shape of the individual n-alkane isotope profile, and show isotopic characteristics similar to marine organic matter. The appearance of oleanane and high 24/(24 + 27)-norcholestane ratios (0.57-0.87) in the saline oils and source rocks confirm a Tertiary organic source

Generalized Wideband Cyclic MUSIC

Directory of Open Access Journals (Sweden)

Zhang-Meng Liu

2009-01-01

Full Text Available The method of Spectral Correlation-Signal Subspace Fitting (SC-SSF fails to separate wideband cyclostationary signals with coherent second-order cyclic statistics (SOCS. Averaged Cyclic MUSIC (ACM method made up for the drawback to some degree via temporally averaging the cyclic cross-correlation of the array output. This paper interprets ACM from another perspective and proposes a new DOA estimation method by generalizing ACM for wideband cyclostationary signals. The proposed method successfully makes up for the aforementioned drawback of SC-SSF and obtains a more satisfying performance than ACM. It is also demonstrated that ACM is a simplified form of the proposed method when only a single spectral frequency is exploited, and the integration of the frequencies within the signal bandwidth helps the new method to outperform ACM.

Virtual screening using combinatorial cyclic peptide libraries reveals protein interfaces readily targetable by cyclic peptides.

Science.gov (United States)

Duffy, Fergal J; O'Donovan, Darragh; Devocelle, Marc; Moran, Niamh; O'Connell, David J; Shields, Denis C

2015-03-23

Protein-protein and protein-peptide interactions are responsible for the vast majority of biological functions in vivo, but targeting these interactions with small molecules has historically been difficult. What is required are efficient combined computational and experimental screening methods to choose among a number of potential protein interfaces worthy of targeting lead macrocyclic compounds for further investigation. To achieve this, we have generated combinatorial 3D virtual libraries of short disulfide-bonded peptides and compared them to pharmacophore models of important protein-protein and protein-peptide structures, including short linear motifs (SLiMs), protein-binding peptides, and turn structures at protein-protein interfaces, built from 3D models available in the Protein Data Bank. We prepared a total of 372 reference pharmacophores, which were matched against 108,659 multiconformer cyclic peptides. After normalization to exclude nonspecific cyclic peptides, the top hits notably are enriched for mimetics of turn structures, including a turn at the interaction surface of human α thrombin, and also feature several protein-binding peptides. The top cyclic peptide hits also cover the critical "hot spot" interaction sites predicted from the interaction crystal structure. We have validated our method by testing cyclic peptides predicted to inhibit thrombin, a key protein in the blood coagulation pathway of important therapeutic interest, identifying a cyclic peptide inhibitor with lead-like activity. We conclude that protein interfaces most readily targetable by cyclic peptides and related macrocyclic drugs may be identified computationally among a set of candidate interfaces, accelerating the choice of interfaces against which lead compounds may be screened.

Milankovitch cyclicity in the paleotropical, fluvial, Late Triassic age strata recovered by the Colorado Plateau Coring Project (CPCP)

Science.gov (United States)

Olsen, P. E.; Mundil, R.; Kent, D.; Rasmussen, C.

2017-12-01

Two questions addressed by the CPCP are: 1) is Milankovitch-paced climate cyclicity recorded in the fluvial Late Triassic age Chinle Formation ( 227-202 Ma); and 2) do geochronological data from the Chinle support the Newark-Hartford astrochronological polarity time scale (1) (APTS). To these ends we examined the upper 157 m (stratigraphic thickness) of Petrified Forest National Park core 1A (Owl Rock, Petrified Forest, and upper Sonsela members), consisting mostly of massive red paleosols and less important fluvial sandstones. A linear age model tied to new U-Pb zircon CA ID-TIMS dates from core 1A, consistent with published data from outcrop (2), yields a duration of about 5 Myr for this interval. Magnetic susceptibility variations, interpreted as reflecting penecontemporaneous soil and sandstone redox conditions, show a clear 12 m cycle corresponding to a 400 kyr cycle based on Fourier analysis in both core and hole. Similar cyclicity is apparent in spectrophotometric data, largely reflecting hematite variability. Weak, higher frequency cycles are present consistent with 100 kyr variability. There is no interpretable 20 kyr signal. Such cyclicity is not an anticipated direct effect of Milankvitch insolation variations, but must reflect non-linear integration of variability that changes dramatically at the eccentricity-scale, brought about by the sedimentary and climate systems. Our results support a direct 405 kyr-level correlation between the fluvial medial Chinle and lacustrine Newark Basin section (middle Passaic Formation), consistent with new and published (3) paleomagnetic polarity stratigraphy from the Chinle, showing that the Milankovitch eccentricity cycles are recorded in lower accumulation rate fluvial systems. Our results also independently support the continuity of the Newark Basin section and corroborate the Newark-Hartford APTS, not allowing for a multi-million year hiatus in the Passaic Formation, as has been asserted (4). We anticipate further

Characterization of Tertiary Catalan lacustrine oil shales: Discovery of extrmely organic sulphur-rich Type I kerogens

Energy Technology Data Exchange (ETDEWEB)

Sinninghe Damste, J.S.; Heras, F.X.C. De Las; Bergen, P.F. Van; Leeuw, J.W. De (Delft Univ. of Technology (Netherlands))

1993-01-01

The kerogens of three Tertiary Catalan lacustrine oil shales were analyzed by light microscopy, flash pyrolysis-gas chromatography-mass spectrometry, and bulk composition methods (elemental analysis, Rock Eval pyrolysis). Two of the three kerogens (Ribesalbes and Campins) are extremely rich in organic sulfur (atomic S[sub org]/C ratio > 0.04) and hydrogen (atomic ratio H/C ratio > 1.5) and are, consequently, classified as Type I-S kerogens. Very characteristic distribution patterns of flash pyrolysis products (e.g., alkan-9- and -10-ones, alkadienes) of the Ribesalbes kerogen revealed that it is predominantly composed of fossilized organic matter of the freshwater alga Botryococcus braunii. These two findings demonstrate that sulfurization of organic matter may also occur in lacustrine sediments provided that sulfate is supplied by external sources. Data on the third kerogen sample (Cerdanya) suggest that the freshwater alga Pediastrum may contain a (partly) aromatic biomacromolecule that is selectively preserved upon diagenesis. These findings testify to the large variability in palaeodepositional conditions in lacutrine environments. A comparison of the biomarker composition of the extract of the Ribesalbes oil shale with the kerogen composition indicate that biomarkers often cannot be used to assess the major sources of organic matter in such settings. A similar conclusion can be drawn from a comparison of literature data concerning the Messel Oil Shale. 75 refs., 18 figs., 7 tabs.

21 CFR 862.1230 - Cyclic AMP test system.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cyclic AMP test system. 862.1230 Section 862.1230....1230 Cyclic AMP test system. (a) Identification. A cyclic AMP test system is a device intended to measure the level of adenosine 3′, 5′-monophosphate (cyclic AMP) in plasma, urine, and other body fluids...

Mapping sediment–landform assemblages to constrain lacustrine sedimentation in a glacier-fed lake catchment in northwest Spitsbergen

OpenAIRE

Bilt, Willem van der; Balascio, Nicholas L.; Bakke, Jostein

2015-01-01

Changes in the deposition of fine-grained rock-flour in glacier-fed lakes reflect glacier variability. This meltwater-driven signal is, however, often overprinted by other processes. To constrain the signature of lacustrine sedimentation, we mapped the catchment of glacier-fed Lake Hajeren in northwest Spitsbergen, identifying sediment sources and linking them to surface processes. To this end, we employed a combined approach of aerial image interpretation and field mapping. Our map comprises...

Behaviour of Cohesionless Soils During Cyclic Loading

DEFF Research Database (Denmark)

Shajarati, Amir; Sørensen, Kris Wessel; Nielsen, Søren Kjær

Offshore wind turbine foundations are typically subjected to cyclic loading from both wind and waves, which can lead to unacceptable deformations in the soil. However, no generally accepted standardised method is currently available, when accounting for cyclic loading during the design of offshore...... wind turbine foundations. Therefore a literature study is performed in order to investigate existing research treating the behaviour of cohesionless soils, when subjected to cyclic loading. The behaviour of a soil subjected to cyclic loading is found to be dependent on; the relative density, mean...

Biostratigraphical correlation of a new interglacial lacustrine deposit from Lind, western Jutland, Denmark

DEFF Research Database (Denmark)

Odgaard, Bent Vad; Krohn, Charlotte Fog; Kronborg, Christian

2008-01-01

and animal macrofossils and two cores were secured from the central part of the basin where the lacustrine deposits have a thickness of about 15 m. The stratigraphy of the deposit can be subdivided into unit A: a lake marl (4 m) superimposed by 3 metres of diatomite and sealed by a thin diamicton. On top...... of unit A follows unit B: 4 metres of gyttja, calcareous at the basal part and sealed by 40 cm of clay. Finally unit C on top of unit B is represented by 1.5 metres of gyttja. The pollen record of unit A can be correlated to the classical Danish record from the nearby Harreskov site (Andersen 1965...

Palaeoenvironments during MIS 3 and MIS 2 inferred from lacustrine intercalations in the loess-palaeosol sequence at Bobingen (southern Germany)

Science.gov (United States)

Mayr, Christoph; Matzke-Karasz, Renate; Stojakowits, Philipp; Lowick, Sally E.; Zolitschka, Bernd; Heigl, Tanja; Mollath, Richard; Theuerkauf, Marian; Weckend, Marc-Oliver; Bäumler, Rupert; Gregor, Hans-Joachim

2017-12-01

Recently exposed loess-palaeosol sequences in the northern Alpine foreland close to Bobingen (southern Germany) were investigated with a multi-proxy approach combining isotopic, geochemical, lithological, and micropalaeontological methods. Luminescence ages date the sections into the Middle and Upper Würmian periods corresponding to Marine Isotope Stages 3 and 2. A gleyic soil horizon at the base was dated to 45 ka and provided a palynoflora dominated by Poaceae, Cyperaceae, and Pinus, as well as frequent aquatic taxa. Lacustrine conditions prevailed after the gley formation until 30 ka, providing a comparatively diverse lacustrine fauna dominated by aquatic gastropods and the ostracod species Candona candida. At the transition to the Upper Würm, climatic conditions became harsh, indicated by accelerated deposition of more coarse-grained loess, organic geochemical indicators, and scarceness of biotic remains. Two tundra-gley horizons in the Upper Würm point to short phases of climatic amelioration with higher humidity also evidenced by reoccurrence of ostracod and aquatic gastropod remains. We propose that these climatic ameliorations were coincident with the Greenland interstadials 4 and 2.

Small-scale lacustrine drifts in Lake Champlain, Vermont

Science.gov (United States)

Manley, Patricia L.; Manley, T.O.; Hayo, Kathryn; Cronin, Thomas

2012-01-01

High resolution CHIRP (Compressed High Intensity Radar Pulse) seismic profiles reveal the presence of two lacustrine sediment drifts located in Lake Champlain's Juniper Deep. Both drifts are positive features composed of highly laminated sediments. Drift B sits on a basement high while Drift A is built on a trough-filling acoustically-transparent sediment unit inferred to be a mass-transport event. These drifts are oriented approximately north–south and are parallel to a steep ridge along the eastern shore of the basin. Drift A, located at the bottom of a structural trough, is classified as a confined, elongate drift that transitions northward to become a system of upslope asymmetric mudwaves. Drift B is perched atop a structural high to the west of Drift A and is classified as a detached elongate drift. Bottom current depositional control was investigated using Acoustic Doppler Current Profilers (ADCPs) located across Drift A. Sediment cores were taken at the crest and at the edges of the Drift A and were dated. Drift source, deposition, and evolution show that these drifts are formed by a water column shear with the highest deposition occurring along its crest and western flank and began developing circa 8700–8800 year BP.

Sources and proxy potential of long chain alkyl diols in lacustrine environments

Science.gov (United States)

Rampen, Sebastiaan W.; Datema, Mariska; Rodrigo-Gámiz, Marta; Schouten, Stefan; Reichart, Gert-Jan; Sinninghe Damsté, Jaap S.

2014-11-01

Long chain 1,13- and 1,15-alkyl diols form the base of a number of recently proposed proxies used for climate reconstruction. However, the sources of these lipids and environmental controls on their distribution are still poorly constrained. We have analyzed the long chain alkyl diol (LCD) composition of cultures of ten eustigmatophyte species, with three species from different families grown at various temperatures, to identify the effect of species composition and growth temperature on the LCD distribution. The results were compared with the LCD distribution of sixty-two lake surface sediments, and with previously reported LCD distributions from marine environments. The different families within the Eustigmatophyceae show distinct LCD patterns, with the freshwater family Eustigmataceae most closely resembling LCD distributions in both marine and lake environments. Unlike the other two eustigmatophyte families analyzed (Monodopsidaceae and Goniochloridaceae), C28 and C30 1,13-alkyl diols and C30 and C32 1,15-alkyl diols are all relatively abundant in the family Eustigmataceae, while the mono-unsaturated C32 1,15-alkyl diol was below detection limit. In contrast to the marine environment, LCD distributions in lakes did not show a clear relationship with temperature. The Long chain Diol Index (LDI), a proxy previously proposed for sea surface temperature reconstruction, showed a relatively weak correlation (R2 = 0.33) with mean annual air temperature used as an approximation for annual mean surface temperature of the lakes. A much-improved correlation (R2 = 0.74, p-value cultures of the family Eustigmataceae, suggesting that algae belonging to this family have an important role as a source for LCDs in lacustrine environments, or, alternatively, that the main sources of LCDs are similarly affected by temperature as the Eustigmataceae. The results suggest that LCDs may have the potential to be applicable as a palaeotemperature proxy for lacustrine environments

On Improvements of Cyclic MUSIC

Directory of Open Access Journals (Sweden)

H. Howard Fan

2005-01-01

Full Text Available Many man-made signals encountered in communications exhibit cyclostationarity. By exploiting cyclostationarity, cyclic MUSIC has been shown to be able to separate signals with different cycle frequencies, thus, to be able to perform signal selective direction of-arrival (DOA estimation. However, as will be shown in this paper, the DOA estimation of cyclic MUSIC is actually biased. We show in this paper that by properly choosing the frequency for evaluating the steering vector, the bias of DOA estimation can be substantially reduced and the performance can be improved. Furthermore, we propose another algorithm exploiting cyclic conjugate correlation to further improve the performance of DOA estimation. Simulation results show the effectiveness of both of our methods.

The lacustrine sediment record of Oberwinkler Maar (Eifel, Germany): Chironomid and macro-remain-based inferences of environmental changes during Oxygen Isotope Stage 3

NARCIS (Netherlands)

Engels, S.; Bohncke, S.J.P.; Heiri, O.; Schaber, K.; Sirocko, F.

2008-01-01

The lacustrine record of Oberwinkler Maar (Eifel, Germany) is the northernmost continuous record documenting the Weichselian Pleniglacial in central Europe - a period characterized by multiple abrupt climate oscillations known as the Dansgaard/Oeschger cycles. Here, the results of a high-resolution

Statistical damage constitutive model for rocks subjected to cyclic stress and cyclic temperature

Science.gov (United States)

Zhou, Shu-Wei; Xia, Cai-Chu; Zhao, Hai-Bin; Mei, Song-Hua; Zhou, Yu

2017-10-01

A constitutive model of rocks subjected to cyclic stress-temperature was proposed. Based on statistical damage theory, the damage constitutive model with Weibull distribution was extended. Influence of model parameters on the stress-strain curve for rock reloading after stress-temperature cycling was then discussed. The proposed model was initially validated by rock tests for cyclic stress-temperature and only cyclic stress. Finally, the total damage evolution induced by stress-temperature cycling and reloading after cycling was explored and discussed. The proposed constitutive model is reasonable and applicable, describing well the stress-strain relationship during stress-temperature cycles and providing a good fit to the test results. Elastic modulus in the reference state and the damage induced by cycling affect the shape of reloading stress-strain curve. Total damage induced by cycling and reloading after cycling exhibits three stages: initial slow increase, mid-term accelerated increase, and final slow increase.

Cyclic deformation of zircaloy-4 at room temperature

International Nuclear Information System (INIS)

Armas, A. F; Herenu, S; Bolmaro, R; Alvarez-Armas, I

2003-01-01

Annealed materials hardens under low cyclic fatigue tests.However, FCC metals tested with medium strain amplitudes show an initial cyclic softening.That behaviour is related with the strong interstitial atom-dislocation interactions.For HCP materials the information is scarce.Commercial purity Zirconium and Zircaloy-4 alloys show also a pronounced cyclic softening, similar to Titanium alloys.Recently the rotation texture induced softening model has been proposed according to which the crystals are placed in a more favourable deformation orientation by prismatic slip due to the cyclic strain.The purpose of the current paper is the presentation of decisive results to discuss the causes for cyclic softening of Zircaloy-4. Low cycle fatigue tests were performed on recrystallized Zircaloy-4 samples.The cyclic behaviour shows an exponential softening at room temperature independently of the deformation range.Only at high temperature a cyclic hardening is shown at low number of cycles.Friction stresses, related with dislocation movement itself, and back stresses, related with dislocation pile-ups can be calculated from the stress-strain loops.The cyclic softening is due to diminishing friction stress while the starting hardening behaviour is due to increasing back stresses.The rotation texture induced softening model is ruled out assuming instead a model based on dislocation unlocking from interstitial oxygen solute atoms

[Cyclic Cushing's Syndrome - rare or rarely recognized].

Science.gov (United States)

Kiałka, Marta; Doroszewska, Katarzyna; Mrozińska, Sandra; Milewicz, Tomasz; Stochmal, Ewa

2015-01-01

Cyclic Cushing's syndrome is a type of Cushing's disease which is characterized by alternating periods of increasing and decreasing levels of cortisol in the blood. The diagnostic criteria for cyclic Cushing's syndrome are at least three periods of hypercortisolism alternating with at least two episodes of normal levels of serum cortisol concentration. The epidemiology, signs, symptoms, pathogenesis and treatment of cyclic Cushing's syndrome have been discussed.

Reconstruction of a saline, lacustrine carbonate system (Priabonian, St-Chaptes Basin, SE France): Depositional models, paleogeographic and paleoclimatic implications

Science.gov (United States)

Lettéron, Alexandre; Hamon, Youri; Fournier, François; Séranne, Michel; Pellenard, Pierre; Joseph, Philippe

2018-05-01

A 220-m thick carbonate-dominated succession has been deposited in shallow-water, saline lake environments during the early to middle Priabonian (MP17A-MP18 mammal zones) in the Saint-Chaptes Basin (south-east France). The palaeoenvironmental, paleoclimatic and palaeogeographic significance of such saline lake carbonates has been deciphered on the basis of a multi-proxy analyses including: 1) depositional and diagenetic features; 2) biological components (molluscs, benthic foraminifera, characean gyrogonites, spores and pollens); 3) carbon and oxygen stable isotopes; 4) trace elements; and 5) clay mineralogy. Five stages of lacustrine system evolution have been identified: 1) fresh-water closed lake under dry climate (unit U1); 2) fresh to brackish water lacustrine deltaic system with a mixed carbonate-siliciclastic sedimentation under relatively wet climatic conditions (unit U2); 3) salt-water lacustrine carbonate system under humid climatic setting (unit U3); 4) evaporitic lake (unit U4); and 5) closed lake with shallow-water carbonate sedimentation under subtropical to Mediterranean climate with dry seasons (unit U5). Upper Eocene aridification is evidenced to have started as early as the earliest Priabonian (unit U1: MP17A mammal zone). A change from humid to dryer climatic conditions is recorded between units U3 and U4. The early to middle Priabonian saline lake is interpreted as an athalassic (inland) lake that have been transiently connected with neighboring salt lakes influenced by seawater and/or fed with sulfates deriving from recycling of evaporites. Maximum of connection with neighboring saline lakes (Mormoiron Basin, Camargue and Central grabens, Hérault Basin) likely occurred during unit U3 and at the base of unit U5. The most likely sources of salts of these adjacent basins are: 1) Triassic evaporites derived from salt-diapirs (Rhône valley) or from paleo-outcrops located east of the Durance fault or offshore in the Gulf of Lion; or 2) marine

Soft-sediment deformation structures in cores from lacustrine slurry deposits of the Late Triassic Yanchang Fm. (central China

Directory of Open Access Journals (Sweden)

Yang Renchao

2016-09-01

Full Text Available The fine-grained autochthonous sedimentation in the deep part of a Late Triassic lake was frequently interrupted by gravity-induced mass flows. Some of these mass flows were so rich in water that they must have represented slurries. This can be deduced from the soft-sediment deformation structures that abound in cores from these lacustrine deposits which constitute the Yanchang Fm., which is present in the Ordos Basin (central China.

Cyclic transformation of orbital angular momentum modes

International Nuclear Information System (INIS)

Schlederer, Florian; Krenn, Mario; Fickler, Robert; Malik, Mehul; Zeilinger, Anton

2016-01-01

The spatial modes of photons are one realization of a QuDit, a quantum system that is described in a D-dimensional Hilbert space. In order to perform quantum information tasks with QuDits, a general class of D-dimensional unitary transformations is needed. Among these, cyclic transformations are an important special case required in many high-dimensional quantum communication protocols. In this paper, we experimentally demonstrate a cyclic transformation in the high-dimensional space of photonic orbital angular momentum (OAM). Using simple linear optical components, we show a successful four-fold cyclic transformation of OAM modes. Interestingly, our experimental setup was found by a computer algorithm. In addition to the four-cyclic transformation, the algorithm also found extensions to higher-dimensional cycles in a hybrid space of OAM and polarization. Besides being useful for quantum cryptography with QuDits, cyclic transformations are key for the experimental production of high-dimensional maximally entangled Bell-states. (paper)

Synthesis of Cyclic Py-Im Polyamide Libraries

OpenAIRE

Li, Benjamin C.; Montgomery, David C.; Puckett, James W.; Dervan, Peter B.

2013-01-01

Cyclic Py-Im polyamides containing two GABA turn units exhibit enhanced DNA binding affinity, but extensive studies of their biological properties have been hindered due to synthetic inaccessibility. A facile modular approach toward cyclic polyamides has been developed via microwave-assisted solid-phase synthesis of hairpin amino acid oligomer intermediates followed by macrocyclization. A focused library of cyclic polyamides 1–7 targeted to the androgen response element (ARE) and the estrogen...

Supplementary Material for: The arabidopsis cyclic nucleotide interactome

KAUST Repository

Donaldson, Lara; Meier, Stuart; Gehring, Christoph A

2016-01-01

Abstract Background Cyclic nucleotides have been shown to play important signaling roles in many physiological processes in plants including photosynthesis and defence. Despite this, little is known about cyclic nucleotide-dependent signaling mechanisms in plants since the downstream target proteins remain unknown. This is largely due to the fact that bioinformatics searches fail to identify plant homologs of protein kinases and phosphodiesterases that are the main targets of cyclic nucleotides in animals. Methods An affinity purification technique was used to identify cyclic nucleotide binding proteins in Arabidopsis thaliana. The identified proteins were subjected to a computational analysis that included a sequence, transcriptional co-expression and functional annotation analysis in order to assess their potential role in plant cyclic nucleotide signaling. Results A total of twelve cyclic nucleotide binding proteins were identified experimentally including key enzymes in the Calvin cycle and photorespiration pathway. Importantly, eight of the twelve proteins were shown to contain putative cyclic nucleotide binding domains. Moreover, the identified proteins are post-translationally modified by nitric oxide, transcriptionally co-expressed and annotated to function in hydrogen peroxide signaling and the defence response. The activity of one of these proteins, GLYGOLATE OXIDASE 1, a photorespiratory enzyme that produces hydrogen peroxide in response to Pseudomonas, was shown to be repressed by a combination of cGMP and nitric oxide treatment. Conclusions We propose that the identified proteins function together as points of cross-talk between cyclic nucleotide, nitric oxide and reactive oxygen species signaling during the defence response.

Functionalized linear and cyclic polyolefins

Energy Technology Data Exchange (ETDEWEB)

Tuba, Robert; Grubbs, Robert H.

2018-02-13

This invention relates to methods and compositions for preparing linear and cyclic polyolefins. More particularly, the invention relates to methods and compositions for preparing functionalized linear and cyclic polyolefins via olefin metathesis reactions. Polymer products produced via the olefin metathesis reactions of the invention may be utilized for a wide range of materials applications. The invention has utility in the fields of polymer and materials chemistry and manufacture.

Climatic instability before the Miocene Climatic Optimum reflected in a Central European lacustrine record from the Most Basin in the Czech Republic

Czech Academy of Sciences Publication Activity Database

Matys Grygar, Tomáš; Hošek, Michal; Mach, K.; Schnabl, Petr; Martinez, M.

2017-01-01

Roč. 485, NOV (2017), s. 930-945 ISSN 0031-0182 R&D Projects: GA ČR(CZ) GA16-00800S Institutional support: RVO:61388980 ; RVO:67985831 Keywords : Chemostratigraphy * Cyclostratigraphy * Lacustrine * Magnetostratigraphy * MCO * Siliciclastic Subject RIV: DD - Geochemistry; DB - Geology ; Mineralogy (GLU-S) OBOR OECD: Geology Impact factor: 2.578, year: 2016

Cyclic Processing for Context Fusion

DEFF Research Database (Denmark)

Kjærgaard, Mikkel Baun

2007-01-01

Many machine-learning techniques use feedback information. However, current context fusion systems do not support this because they constrain processing to be structured as acyclic processing. This paper proposes a generalization which enables the use of cyclic processing in context fusion systems....... A solution is proposed to the inherent problem of how to avoid uncontrollable looping during cyclic processing. The solution is based on finding cycles using graph-coloring and breaking cycles using time constraints....

Sexually antagonistic coevolution for sexual harassment can act as a barrier to further invasions by parthenogenesis.

Science.gov (United States)

Kawatsu, Kazutaka

2013-02-01

The assumption of a twofold cost of sex not only complicates the maintenance of sex but also sets conditions for sexual conflict: in organisms with the twofold cost, males often sexually harass females. Sexual harassment is detrimental to female fitness and thus might help maintain sexual populations if male harassment inflicts a harsher cost on parthenogens than on sexual females (asymmetric harassment cost). However, the generality of this concept is now considered doubtful because selective harassment of parthenogens results in loss of mating opportunities for males. Using three mathematical models, I show here that sexual harassment still can impose the asymmetric cost on parthenogens. First, I apply the Lotka-Volterra model to show the degree of asymmetric harassment cost that permits sex to be maintained stably in the population. Second, using adaptive dynamics, I examine whether sexually antagonistic coevolution for sexual harassment, which occurs only in sexual populations, can promote the asymmetric harassment cost. Finally, an individual-based model, which assumes a spatial structure unlike that in the other two, demonstrates that the asymmetric evolution of harassment cost prevents further invasions of parthenogens from different patches into sexual lineages; these mechanisms may account for allopatric distributions of sexual and parthenogenetic lineages as well as the maintenance of sex.

Chapter F: Preliminary Bibliography of Lacustrine Diatomite Deposits in the Western United States and Related Topics

Science.gov (United States)

Bolm, Karen S.; Wallace, Alan R.; Moyle, Phillip R.; Bliss, James D.; Orris, Greta J.

2003-01-01

Introduction As part of the assessment of lacustrine diatomite resources in the Western United States (fig. 1), U.S. Geological Survey (USGS) project members conducted a review of literature relating to the formation, location, and nature of deposits in the study area. This preliminary bibliography consists of selected publications to identify, locate, and describe the deposits to be studied, to characterize common geologic factors about the deposits, and to better understand the factors that control their formation, preservation, or destruction. The bibliography also serves as a resource for other workers to research the topic. References included in the preliminary bibliography were gathered by searching existing bibliographic data bases and library collections. Project researchers also contributed references that they found during the course of their work. This bibliography should be considered a working document that will grow as research and literature searches continue. Clearly, many significant publications may be missing from this preliminary list; therefore, USGS staff members intend to issue a revised bibliography as project work progresses. To assure completeness, input from other researchers and industry is welcome. Although the focus of this bibliography is lacustrine diatomite deposits of the Western United States, additional references that provide a foundation of knowledge for the study of diatomites, diatoms, and diatom-related processes (ecology, geology, geochemistry) and for the uses and behavior of diatomite have also been included. An index of keywords has been added to this bibliography, designed to help the user locate reports by topic or by geographic location. The letter 'A' following a number indicates that the report referenced is an abstract.

Geochemical characteristics of Holocene laminated sapropel (unit II) and underlying lacustrine unit III in the Black Sea

Science.gov (United States)

Dean, Walter E.; Arthur, Michael A.

2011-01-01

eg 1 of the 1988 R/V Knorr expeditions to the Black Sea recovered 90 gravity and box cores. The longest recovery by gravity cores was about 3 meters, with an average of about 2.5 meters, recovering all of the Holocene and upper Pleistocene sections in the Black Sea. During the latest Pleistocene glaciation, sea level dropped below the 35-meters-deep Bosporus outlet sill of the Black Sea. Therefore throughout most of its history the Black Sea was a lake, and most of its sediments are lacustrine. The oldest sediments recovered (older than 8,000 calendar years) consist of massive to coarsely banded lacustrine calcareous clay designated as lithologic Unit III, generally containing less than 1 percent organic carbon (OC). The base of overlying Unit II marks the first incursion of Mediterranean seawater into the Black Sea, and the onset of bottom-water anoxia about 7,900 calendar years. Unit II contains as much as 15 percent OC in cores from the deepest part of the Black Sea (2,200 meters). The calcium carbonate (CaCO3) remains of the coccolith Emiliania huxleyi form the distinctive white laminae of overlying Unit I. The composition of Unit III and Unit II sediments are quite different, reflecting different terrigenous clastic sources and increased contributions from hydrogenous and biogenic components in anoxic Unit II sapropel. In Unit II, positive covariance between OC and three trace elements commonly concentrated in OC-rich sediments where sulfate reduction has occurred (molybdenum, nickel, and vanadium) and a nutrient (phosphorus) suggest a large marine source for these elements although nickel and vanadium also have a large terrigenous clastic source. The marine sources may be biogenic or hydrogenous. A large biogenic source is also suggested for copper and cobalt. Because abundant pyrite forms in the water column and sediments of the Black Sea, we expected to find a large hydrogenous iron component, but a strong covariance of iron with aluminum suggests that the

Lacustrine basin evolution and coal accumulation of the Middle Jurassic in the Saishiteng coalfield, northern Qaidam Basin, China

Directory of Open Access Journals (Sweden)

Meng Li

2016-07-01

Full Text Available Based on an extensive borehole survey of the Middle Jurassic coal-bearing sequences in the Saishiteng coalfield, northern Qaidam Basin (NQB, a total of 20 rock types and 5 sedimentary facies were identified, including braided river, meandering river, braided delta, meandering river delta, and lacustrine facies. The distribution of rock types and sedimentary facies contributed to the reconstruction of three periods' sedimentary facies maps of the Middle Jurassic in the Saishiteng coalfield, namely, the Dameigou age, the early Shimengou age and the late Shimengou age. That also provided the basis for the development of a three-stage depositional model of the Middle Jurassic in the NQB, indicating the lacustrine basin of the NQB in the Dameigou age and early Shimengou age were corresponding to an overfill basin, and that in the late Shimengou age was related to a balanced-fill basin. The analysis of the stability and structure of coal seams based on sedimentary facies maps showed that the preferred coal-forming facies in the Saishiteng coalfield were inter-delta bay and interdistributary bay of lower delta plain in the Dameigou age. In particular, the swamps that developed on the subaqueous palaeohigh favored the development of thick coal seams. Thus, minable coal seams may also be found along the Pingtai palaeohigh in the western part of the Saishiteng coalfield.

Comparison Of INAA Methods (Long Conventional, Cyclic And Pseudo-Cyclic) For The Determination Of Se In Biological Samples

International Nuclear Information System (INIS)

Sarheel, A.

2004-01-01

Selenium content in serum blood, sample were received from international comparison programme (SABC) has been determined by Cyclic irradiation, pseudo-cyclic irradiation and long irradiation conventional Instrumental neutron activation analysis through the 162 keV gamma ray of the 77m Se nuclide for both cyclic and pseudo-cyclic and 264 keV gamma ray of 75 Se nuclide for conventional (long irradiation). The CINAA involve irradiation of samples for 20 s, decay for 15 s and counting for 20 s, samples recycling four times to improve the precision. The PCINAA involve irradiation of samples for 20 s, decay for 20 s and counting for 30s, samples recycling four times day by day. The Conventional (long irradiation) involve irradiation of samples for 20 hr (1 week), decay for 4 weeks and counting for 20 hr. The accuracy has been evaluated by analyzing the certified reference materials. (Author)

Cyclic Soft Groups and Their Applications on Groups

Directory of Open Access Journals (Sweden)

Hacı Aktaş

2014-01-01

Full Text Available In crisp environment the notions of order of group and cyclic group are well known due to many applications. In this paper, we introduce order of the soft groups, power of the soft sets, power of the soft groups, and cyclic soft group on a group. We also investigate the relationship between cyclic soft groups and classical groups.

HOST liner cyclic facilities: Facility description

Science.gov (United States)

Schultz, D.

1982-01-01

A quartz lamp box, a quartz lamp annular rig, and a low pressure liner cyclic can rig planned for liner cyclic tests are described. Special test instrumentation includes an IR-TV camera system for measuring liner cold side temperatures, thin film thermocouples for measuring liner hot side temperatures, and laser and high temperature strain gages for obtaining local strain measurements. A plate temperature of 2,000 F was obtained in an initial test of an apparatus with three quartz lamps. Lamp life, however, appeared to be limited for the standard commercial quartz lamps available. The design of vitiated and nonvitiated preheaters required for the quartz lamp annular rig and the cyclic can test rigs is underway.

Rhodium-Catalyzed Dehydrogenative Borylation of Cyclic Alkenes

Science.gov (United States)

Kondoh, Azusa; Jamison, Timothy F.

2010-01-01

A rhodium-catalyzed dehydrogenative borylation of cyclic alkenes is described. This reaction provides direct access to cyclic 1-alkenylboronic acid pinacol esters, useful intermediates in organic synthesis. Suzuki-Miyaura cross-coupling applications are also presented. PMID:20107646

Types of soft-sediment deformation structures in a lacustrine Ploužnice member (Stephanian, Gzhelian, Pennsylvanian, Bohemian Massif), their timing, and possible trigger mechanism

Czech Academy of Sciences Publication Activity Database

Stárková, M.; Martínek, K.; Mikuláš, Radek; Rosenau, N.

2015-01-01

Roč. 104, č. 5 (2015), s. 1277-1298 ISSN 1437-3254 Institutional support: RVO:67985831 Keywords : soft-sediment deformation structures * bioturbation * early diagenetic carbonate * lacustrine facies * Bohemian Massif * Stephanian C * Krkonoše Piedmont Basin Subject RIV: DB - Geology ; Mineralogy Impact factor: 2.133, year: 2015

3' : 5'-Cyclic AMP-dependent 3'

NARCIS (Netherlands)

Mato, José M.; Krens, Frans A.; Haastert, Peter J.M. van; Konijn, Theo M.

1977-01-01

Suspensions of 3':5'-cyclic AMP (cAMP)-sensitive cells of Dictyostelium discoideum responded to a cAMP pulse with increased 3':5'-cyclic GMP (cGMP) levels. Under the assay conditions used (2 × 10^8 cells per ml in 10 mM phosphate buffer, pH 6.0) cAMP (5 × 10-8 M final concentration) increased cGMP

Nearly Cyclic Pursuit and its Hierarchical variant for Multi-agent Systems

DEFF Research Database (Denmark)

Iqbal, Muhammad; Leth, John-Josef; Ngo, Trung Dung

2015-01-01

The rendezvous problem for multiple agents under nearly cyclic pursuit and hierarchical nearly cyclic pursuit is discussed in this paper. The control law designed under nearly cyclic pursuit strategy enables the agents to converge at a point dictated by a beacon. A hierarchical version of the nea......The rendezvous problem for multiple agents under nearly cyclic pursuit and hierarchical nearly cyclic pursuit is discussed in this paper. The control law designed under nearly cyclic pursuit strategy enables the agents to converge at a point dictated by a beacon. A hierarchical version...

Organic compositions of lacustrine source rocks in Jiyang super-depression and its implication to petroleum geology

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The compositions of organic matter in four immature source rocks from Tertiary strata of Jiyang super-depression, the most typical continental rift subsidence basin in East China, have been studied by different extracting methods with CHCl3, MAC and CS2/NMP, respectively. The results suggest that there are great differences among the chemical compositions of organic matter in the source rocks derived from different depositional environments. About 79% of all the organic matter exists by non- covalent bond in the Es4 source rocks which were deposited under the saline lacustrine, indicating that its organic matter is not the real kerogen, but mainly composed of soluble organic matter which is easy to generate hydrocarbon at lower temperature. This is why the immature oils were derived from Es4 source rocks in Dongying depression. In contrast, around 60% of organic matter exists by covalent bond in Es3 source rocks which were deposited under the deep brackish-fresh lacustrine, showing that Es3 source rocks are mainly composed of kerogen producing mature hydrocarbon at higher temperature. The thermal simulation experiments, upon the remaining solid source rocks which were sequentially extracted by the three solvents, have been carried out. The chloroform extracts from the simulation product have been compared with the other three solvent extracts gained at room temperature. It is obvious that remarkable odd/even predominance (OEP) is mainly the characteristic of soluble organic matter; phytane mostly exists in the soluble organic matter by means of non-covalent bonds and characteristics of soluble organic matter are similar to these in immature oils produced in Jiyang super-depression.

Cyclic creep-rupture behavior of three high-temperature alloys.

Science.gov (United States)

Halford, G. R.

1972-01-01

Study of some important characteristics of the cyclic creep-rupture curves for the titanium alloy 6Al-2Sn-4Zr-2Mo at 900 and 1100 F (755 and 865 K), the cobalt-base alloy L-605 at 1180 F (910 K), and for two hardness levels of 316 stainless steel at 1300 F (980 K). The cyclic creep-rupture curve relates tensile stress and tensile time-to-rupture for strain-limited cyclic loading and has been found to be independent of the total strain range and the level of compressive stress employed in the cyclic creep-rupture tests. The cyclic creep-rupture curve was always found to be above and to the right of the conventional (constant load) monotonic creep-rupture curve by factors ranging from 2 to 10 in time-to-rupture. This factor tends to be greatest when the creep ductility is large. Cyclic creep acceleration was observed in every cyclic creep-rupture test conducted. The phenomenon was most pronounced at the highest stress levels and when the tensile and compressive stresses were completely reversed. In general, creep rates were found to be lower in compression than in tension for equal true stresses. The differences, however, were strongly material-dependent.

Late Holocene monsoon climate as evidenced by proxy records from a lacustrine sediment sequence in western Guangdong, South China

Science.gov (United States)

Zhong, Wei; Cao, jiayuan; Xue, Jibin; Ouyang, Jun; Tang, Xiaohong; Yin, Huanling; Liao, Congyun; Long, Kun

2014-02-01

The study of a 300-cm-thick exposed lacustrine sediment section in the Hedong village in Zhaoqing area which is located in sub-tropical west Guangdong Province in South China, demonstrates that the lacustrine sedimentary sequence possibly contains evidence for exploring variation of Asian monsoon climate. Multi-proxy records, including the humification intensity, total organic carbon, and grain size fractions, reveal a general trend towards dry and cold conditions in the late Holocene that this is because of a decrease in solar insolation on an orbital scale. Three intensified Asian summer monsoon (ASM) intervals (˜3300-3000 cal yr BP, ˜2600-1600 cal yr BP, and ˜900-600 cal yr BP), and three weakened ASM intervals (˜4000-3300 cal yr BP, ˜3000-2600 cal yr BP, and ˜1600-900 cal yr BP) are identified. Our humification record (HDcal) shows a good correlation on multi-centennial scale with the tree ring Δ14C record, a proxy of solar activity. A spectral analysis of HDcal reveals four significant cycles, i.e., ˜1250 yr, 300 yr, 110 yr, and 70 yr, and most of these cycles are related to the solar activity. Our findings indicate that solar output and oceanic-atmospheric circulation probably have influenced the late Holocene climate variability in the study region.

In-situ monitoring of deformation of clayey and volcanic sequences in the lacustrine plain of Iztapalapa, Mexico City

Science.gov (United States)

Carreon-Freyre, D.; Cerca, M.; Barrientos, B.; Gutierrez, R.; Blancas, D.

2012-12-01

Major cities of Central Mexico with lowering of land elevation problems are located in inter-volcanic and fault bounded basins within the central Trans-Mexican Volcanic Belt (TMVB). The most representative and studied case of ground deformation is Mexico City, where the Iztapalapa Municipality presents the highest population density. This area is located over the geological contact between the "Sierra de Santa Catarina" volcanic range and a lacustrine plain. Filling of lacustrine basins includes silty and clayey sediments as well as pyroclastic deposits (coarse and fine grained) and volcanic rocks layers. We used Ground Penetrating Radar (GPR) and MASW prospection to evaluate contrasts in the physical properties of fine grained soils and identify geometry of the deformational features and implemented a mechanical system for in situ monitoring in fractured sites. Deformational features in this basin reflect an interplay between the geological history (depositional conditions), load history, seismic activity, and faulting. Plastic mechanical behaviour predominates in these clayey sediments and differential deformation locally triggers brittle fracturing and/or subsidence of the surface. In this work we present the results of monitoring and characterization of ground deformation and fracturing in different sequences, our results show a dynamic interplay between the mechanisms of ground fracturing and the stress history of sedimentary sequences. Relating the mechanical behaviour of the studied sequences with variations of physical and geological properties should be taken into account to estimate land level lowering and risk of fracturing for urban development planning.

Cyclic multiverses

Science.gov (United States)

Marosek, Konrad; Dąbrowski, Mariusz P.; Balcerzak, Adam

2016-09-01

Using the idea of regularization of singularities due to the variability of the fundamental constants in cosmology we study the cyclic universe models. We find two models of oscillating and non-singular mass density and pressure (`non-singular' bounce) regularized by varying gravitational constant G despite the scale factor evolution is oscillating and having sharp turning points (`singular' bounce). Both violating (big-bang) and non-violating (phantom) null energy condition models appear. Then, we extend this idea on to the multiverse containing cyclic individual universes with either growing or decreasing entropy though leaving the net entropy constant. In order to get an insight into the key idea, we consider the doubleverse with the same geometrical evolution of the two `parallel' universes with their physical evolution [physical coupling constants c(t) and G(t)] being different. An interesting point is that there is a possibility to exchange the universes at the point of maximum expansion - the fact which was already noticed in quantum cosmology. Similar scenario is also possible within the framework of Brans-Dicke theory where varying G(t) is replaced by the dynamical Brans-Dicke field φ(t) though these theories are slightly different.

Earthquake-induced soft-sediment deformation structures in Late Pleistocene lacustrine deposits of Issyk-Kul lake (Kyrgyzstan)

Science.gov (United States)

Gladkov, A. S.; Lobova, E. U.; Deev, E. V.; Korzhenkov, A. M.; Mazeika, J. V.; Abdieva, S. V.; Rogozhin, E. A.; Rodkin, M. V.; Fortuna, A. B.; Charimov, T. A.; Yudakhin, A. S.

2016-10-01

This paper discusses the composition and distribution of soft-sediment deformation structures induced by liquefaction in Late Pleistocene lacustrine terrace deposits on the southern shore of Issyk-Kul Lake in the northern Tien Shan mountains of Kyrgyzstan. The section contains seven deformed beds grouped in two intervals. Five deformed beds in the upper interval contain load structures (load casts and flame structures), convolute lamination, ball-and-pillow structures, folds and slumps. Deformation patterns indicate that a seismic trigger generated a multiple slump on a gentle slope. The dating of overlying subaerial deposits suggests correlation between the deformation features and strong earthquakes in the Late Pleistocene.

Macromolecular Networks Containing Fluorinated Cyclic Moieties

Science.gov (United States)

2015-12-12

Briefing Charts 3. DATES COVERED (From - To) 17 Nov 2015 – 12 Dec 2015 4. TITLE AND SUBTITLE Macromolecular Networks Containing Fluorinated Cyclic... FLUORINATED CYCLIC MOIETIES 12 December 2015 Andrew J. Guenthner,1 Scott T. Iacono,2 Cynthia A. Corley,2 Christopher M. Sahagun,3 Kevin R. Lamison,4...Reinforcements Good Flame, Smoke, & Toxicity Characteristics Low Water Uptake with Near Zero Coefficient of Hygroscopic Expansion ∆ DISTRIBUTION A

Caffeine, cyclic AMP and postreplication repair of mammalian DNA

International Nuclear Information System (INIS)

Ehmann, U.K.

1976-01-01

The methylxanthines, caffeine and theophylline, inhibit postreplication repair of DNA in mammalian cells. Because they also inhibit cyclic AMP phosphodiesterase, it was thought that there might be some connection between concentrations of cyclic AMP and postreplication repair. This possibility was tested by performing DNA sedimentation experiments with a cyclic AMP-resistant mouse lymphoma cell mutant and its wild-type counterpart. The results show that there is no connection between cellular cyclic AMP concentrations and the rate of postreplication repair. Therefore, it is more likely that caffeine and theophylline inhibit postreplication repair by some other means, such as by binding to DNA

Distinguishing megathrust from intraplate earthquakes using lacustrine turbidites (Laguna Lo Encañado, Central Chile)

Science.gov (United States)

Van Daele, Maarten; Araya-Cornejo, Cristian; Pille, Thomas; Meyer, Inka; Kempf, Philipp; Moernaut, Jasper; Cisternas, Marco

2017-04-01

One of the main challenges in seismically active regions is differentiating paleo-earthquakes resulting from different fault systems, such as the megathrust versus intraplate faults in subductions settings. Such differentiation is, however, key for hazard assessments based on paleoseismic records. Laguna Lo Encañado (33.7°S; 70.3°W; 2492 m a.s.l.) is located in the Central Chilean Andes, 50 km east of Santiago de Chile, a metropole with about 7,000,000 inhabitants. During the last century the study area experienced 3 large megathrust earthquakes (1906, 1985 and 2010) and 2 intraplate earthquakes (1945 and 1958) (Lomnitz, 1960). While the megathrust earthquakes cause Modified Mercalli Intensities (MMIs) of VI to VII at the lake (Van Daele et al., 2015), the intraplate earthquakes cause peak MMIs up to IX (Sepúlveda et al., 2008). Here we present a turbidite record of Laguna Lo Encañado going back to 1900 AD. While geophysical data (3.5 kHz subbottom seismic profiles and side-scan sonar data) provides a bathymetry and an overview of the sedimentary environment, we study 15 short cores in order to understand the depositional processes resulting in the encountered lacustrine turbidites. All mentioned earthquakes triggered turbidites in the lake, which are all linked to slumps in proximal areas, and are thus resulting from mass wasting of the subaquatic slopes. However, turbidites linked to the intraplate earthquakes are additionally covered by turbidites of a finer-grained, more clastic nature. We link the latter to post-seismic erosion of onshore landslides, which need higher MMIs to be triggered than subaquatic mass movements (Howarth et al., 2014). While intraplate earthquakes can cause MMIs up to IX and higher, megathrust earthquakes do not cause sufficiently high MMIs at the lake to trigger voluminous onshore landslides. Hence, the presence of these post-seismic turbidites allows to distinguish turbidites triggered by intraplate earthquakes from those

The Cyclicality of New Product Introductions

OpenAIRE

Kostas Axarloglou

2003-01-01

This study analyzes empirically the cyclical nature of the timing of new product introductions in U.S. manufacturing. New product introductions vary more in nonseasonal frequencies than in seasonal frequencies. However, the seasons alone account for only a small part of their total variability with demand factors being much more important. Demand fluctuations account for 35%80% and 17%43%, respectively, of the seasonal and cyclical variability of new product introductions in various industrie...

Nature of a solar cyclicity

International Nuclear Information System (INIS)

Romanchuk, P.R.

1981-01-01

The paper contains a critical review of works on studying a cyclic character of solar activity. An introduction of cyclic curves with a frequency spectrum is established to be insolvent. The Wolf, Newcomb and Waldmeier approach seems to be useful. Some evidence is given in favour of the author's conception of solar activity ciclicity of a tide nature. It is accounted for a continuous double and single effect of planets, a resonant character of this effect due to which a 10-year period of Jupiter and Saturn is transformed into an 11-year cycle of activity [ru

Safety Discrete Event Models for Holonic Cyclic Manufacturing Systems

Science.gov (United States)

Ciufudean, Calin; Filote, Constantin

In this paper the expression “holonic cyclic manufacturing systems” refers to complex assembly/disassembly systems or fork/join systems, kanban systems, and in general, to any discrete event system that transforms raw material and/or components into products. Such a system is said to be cyclic if it provides the same sequence of products indefinitely. This paper considers the scheduling of holonic cyclic manufacturing systems and describes a new approach using Petri nets formalism. We propose an approach to frame the optimum schedule of holonic cyclic manufacturing systems in order to maximize the throughput while minimize the work in process. We also propose an algorithm to verify the optimum schedule.

Regulation of phospholipid synthesis in Mycobacterium smegmatis by cyclic adenosine monophosphate

International Nuclear Information System (INIS)

Sareen, Monica; Kaur, Harpinder; Khuller, G.K.

1993-01-01

Forskolin, an adenylate cyclase activator and a cyclic AMP analogue, dibutyryl cyclic AMP have been used to examine the relationship between intracellular levels of cyclic AMP and lipid synthesis in Mycobacterium smegmatis. Total phospholipid content was found to be increased in forskolin grown cells as a result of increased cyclic AMP levels caused by activation of adenylate cyclase. Increased phospholipid content was supported by increased [ 14 C]acetate incorporation as well as increased activity of glycerol-3-phosphate acyltransferase. Pretreatment of cells with dibutyryl cyclic AMP had similar effects on lipid synthesis. Taking all these observations together it is suggested that lipid synthesis is being controlled by cyclic AMP in mycobacteria. (author). 14 refs., 4 tabs

Cyclic deformation of NiTi shape memory alloys

International Nuclear Information System (INIS)

Liu Yong; Van Humbeeck, J.; Xie Zeliang

1999-01-01

Recently, there is an increasing interest in applying the high damping capacity of shape memory alloys (SMAs). The purpose is to explore the feasibility of those materials for the protection of buildings and other civil constructions as a result of earthquake damages. So far, few experimental results have been reported concerning the mechanical cyclic behaviour of SMAs in their martensitic state (ferroelastic). In the present work, the experimental results on the mechanical behaviour of martensitic NiTi SMAs under tension-compression cyclic deformation up to strains of ±4% are summarized with major attention to the damping capacity, characteristic stresses and strains as a function of deformation cycles. Effect of strain rate, strain amplitude and annealing condition on the martensite damping is summarized. Explanation of the cyclic hardening and cyclic softening phenomenon is proposed based on TEM observations. (orig.)

Laterally cyclic loading of monopile in dense sand

DEFF Research Database (Denmark)

Klinkvort, Rasmus Tofte; Hededal, Ole; Svensson, M.

2011-01-01

In order to investigate the response from laterally cyclic loading of monopiles a large centrifuge tests series is ongoing at the Technical University of Denmark (DTU). This paper will present some of the tests carried out with a focus on the influence of accumulation of rotation when changing...... the loading conditions. In these tests the load conditions are controlled by two load characteristics, one controlling the level of the cyclic loading and one controlling the characteristic of the cyclic loading. The centrifuge tests were performed in dense dry sand on a pile with prototype dimensions...

Cyclic cellular automata in 3D

International Nuclear Information System (INIS)

Reiter, Clifford A.

2011-01-01

Highlights: → We explore the self-organization of cyclic cellular automata in 3D. → Von Neumann, Moore and two types of intermediate neighborhoods are investigated. → Random neighborhoods self organize through phases into complex nested structures. → Demons are seen to have many alternatives in 3D. - Abstract: Cyclic cellular automata in two dimensions have long been intriguing because they self organize into spirals and that behavior can be analyzed. The form for the patterns that develop is highly dependent upon the form of the neighborhood. We extend this work to three dimensional cyclic cellular automata and observe self organization dependent upon the neighborhood type. This includes neighborhood types intermediate between Von Neumann and Moore neighborhoods. We also observe that the patterns include nested shells with the appropriate forms but that the nesting is far more complex than the spirals that occur in two dimensions.

Charge initiation schemes for ensuring high-performance operation of cyclic-flow technology cyclic link

Directory of Open Access Journals (Sweden)

S. N. Zharikov

2017-09-01

Full Text Available The authors consider the issue of ensuring the quality of crushing rock mass by drilling and blasting method for high productivity of a cyclic link of a cyclic-flow technology complex. The article contains recommendations for calculating certain parameters of drilling and blasting operations, such as the width of the retaining wall Bp. s, the collapse with account for the retaining wall Вr, the width of the collapse of the rock mass Bf when blasting onto a free surface (for the first row of vertical wells and for the first series of inclined wells, the width of the collapse from the first series of wells B1, the deceleration time τ, the coefficient kβ that takes into account the incline angle of wells β to the horizon. The authors prove the expediency of using a retaining wall in explosions of technological blocks. The authors raise the question about the management of detonation characteristics of explosives produced in the field of application for the most rational impact of an explosion on a rock massif. Since the technological schemes for preparing the rock mass to the excavation, which ensure the high-performance operation of the cyclic link of the cyclic-flow technology, can be different, then the choice of a specific drilling and blasting circuit is depends on the geological conditions and elements of the development system. As a preliminary method of breaking, one can consider the explosion of charges along the diagonal (diagonal blasting schemes on the retaining wall. This method provides sufficient reliability of technological explosions, and with the development of modern means of blasting with decelerations between charges of more than 67 ms, there are nearly no back emissions.

Cyclic Matching Pursuits with Multiscale Time-frequency Dictionaries

DEFF Research Database (Denmark)

Sturm, Bob L.; Christensen, Mads Græsbøll

2010-01-01

We generalize cyclic matching pursuit (CMP), propose an orthogonal variant, and examine their performance using multiscale time-frequency dictionaries in the sparse approximation of signals. Overall, we find that the cyclic approach of CMP produces signal models that have a much lower approximation...

Association of Marijuana Use and Cyclic Vomiting Syndrome

Directory of Open Access Journals (Sweden)

Mithun B. Pattathan

2012-06-01

Full Text Available Cannabis use has become one of the most commonly abused drugs in the world. It is estimated that each year 2.6 million individuals in the USA become new users and most are younger than 19 years of age. Reports describe marijuana use as high as 40–50% in male Cyclic Vomiting Syndrome patients. It is this interest in cannabis in the World, coupled with recognition of a cyclic vomiting illness associated with its chronic use that beckons a review of the most current articles, as well as a contribution from our own experiences in this area. The similarities we have demonstrated for both cannibinoid hyperemesis syndrome and cyclic vomiting make the case that cannibinoid hyperemesis syndrome is a subset of patients who have the diagnoses of cyclic vomiting syndrome and the role of marijuana should always be considered in the diagnosis of CVS, particularly in males.

Design of a cyclic multiverse

Energy Technology Data Exchange (ETDEWEB)

Piao Yunsong, E-mail: yspiao@gucas.ac.c [College of Physical Sciences, Graduate School of Chinese Academy of Sciences, Beijing 100049 (China)

2010-08-09

Recently, it has been noticed that the amplification of the amplitude of curvature perturbation cycle by cycle can lead to a cyclic multiverse scenario, in which the number of universes increases cycle by cycle. However, this amplification will also inevitably induce either the ultimate end of corresponding cycle, or the resulting spectrum of perturbations inside corresponding universe is not scale invariant, which baffles the existence of observable universes. In this Letter, we propose a design of a cyclic multiverse, in which the observable universe can emerges naturally. The significance of a long period of dark energy before the turnaround of each cycle for this implementing is shown.

Design of a cyclic multiverse

International Nuclear Information System (INIS)

Piao Yunsong

2010-01-01

Recently, it has been noticed that the amplification of the amplitude of curvature perturbation cycle by cycle can lead to a cyclic multiverse scenario, in which the number of universes increases cycle by cycle. However, this amplification will also inevitably induce either the ultimate end of corresponding cycle, or the resulting spectrum of perturbations inside corresponding universe is not scale invariant, which baffles the existence of observable universes. In this Letter, we propose a design of a cyclic multiverse, in which the observable universe can emerges naturally. The significance of a long period of dark energy before the turnaround of each cycle for this implementing is shown.

The cyclical character of economic policy in Serbia 2001-2012

Directory of Open Access Journals (Sweden)

Radović-Stojanović Jelena

2014-01-01

Full Text Available This paper investigates the cyclical character of economic policy in Serbia in the period 2001-2012. For this purpose the cyclical movement of the following monetary and fiscal variables have been analysed: M2 money supply, the retail price index, the consumer price index, and the real effective exchange rate as the monetary policy indicators, and budget revenues and budget expenditures as the fiscal policy indicators. In the evaluation of the cyclical character of the economic policy, cross-correlation between the cyclical component of economic policy indicators and the gross domestic product at various lags has been observed. The results of cross-correlation analysis suggest that the budget expenditures are countercyclical and lead the aggregate cycle while the budget revenues are procyclical. The cyclical character of M2 money supply in the Serbian economy is somewhat contradictory, so further investigations of the cyclical character of monetary policy and mutual interdependence of money and output are required. The real effective exchange rate is countercyclical. The prices are procyclical and lag behind the cycles in aggregate economic activity. The procyclical character of prices indicates that the causes of the cyclical fluctuations of aggregate economic activities in Serbia in the period from 2001 to 2012 were on the demand side.

Elevational gradient in the cyclicity of a forest-defoliating insect

Science.gov (United States)

Kyle J. Haynes; Andrew M. Liebhold; Derek M. Johnson

2012-01-01

Observed changes in the cyclicity of herbivore populations along latitudinal gradients and the hypothesis that shifts in the importance of generalist versus specialist predators explain such gradients has long been a matter of intense interest. In contrast, elevational gradients in population cyclicity are largely unexplored. We quantified the cyclicity of gypsy moth...

Robust Cyclic MUSIC Algorithm for Finding Directions in Impulsive Noise Environment

Directory of Open Access Journals (Sweden)

Sen Li

2017-01-01

Full Text Available This paper addresses the issue of direction finding of a cyclostationary signal under impulsive noise environments modeled by α-stable distribution. Since α-stable distribution does not have finite second-order statistics, the conventional cyclic correlation-based signal-selective direction finding algorithms do not work effectively. To resolve this problem, we define two robust cyclic correlation functions which are derived from robust statistics property of the correntropy and the nonlinear transformation, respectively. The MUSIC algorithm with the robust cyclic correlation matrix of the received signals of arrays is then used to estimate the direction of cyclostationary signal in the presence of impulsive noise. The computer simulation results demonstrate that the two proposed robust cyclic correlation-based algorithms outperform the conventional cyclic correlation and the fractional lower order cyclic correlation based methods.

Empirical quantification of lacustrine groundwater discharge - different methods and their limitations

Science.gov (United States)

Meinikmann, K.; Nützmann, G.; Lewandowski, J.

2015-03-01

Groundwater discharge into lakes (lacustrine groundwater discharge, LGD) can be an important driver of lake eutrophication. Its quantification is difficult for several reasons, and thus often neglected in water and nutrient budgets of lakes. In the present case several methods were applied to determine the expansion of the subsurface catchment, to reveal areas of main LGD and to identify the variability of LGD intensity. Size and shape of the subsurface catchment served as a prerequisite in order to calculate long-term groundwater recharge and thus the overall amount of LGD. Isotopic composition of near-shore groundwater was investigated to validate the quality of catchment delineation in near-shore areas. Heat as a natural tracer for groundwater-surface water interactions was used to find spatial variations of LGD intensity. Via an analytical solution of the heat transport equation, LGD rates were calculated from temperature profiles of the lake bed. The method has some uncertainties, as can be found from the results of two measurement campaigns in different years. The present study reveals that a combination of several different methods is required for a reliable identification and quantification of LGD and groundwater-borne nutrient loads.

Centrifuge modelling of a laterally cyclic loaded pile

DEFF Research Database (Denmark)

Klinkvort, Rasmus Tofte; Leth, Caspar Thrane; Hededal, Ole

2010-01-01

A total number of 9 static and 6 cyclic centrifuge tests on laterally loaded piles in very dense, dry sand was erformed. The prototype dimensions of the piles were 1 meter in diameter and penetration depths varying from 6 to 10 meters. The static tests were used to investigate the initial subgrade...... reaction modulus and as a reference for cyclic tests. For the cyclic tests the accumulation of deflections and the change in secant stiffness of the soil from repetitive loading were investigated. From all the tests carried out accumulations of deflections were seen. rom the centrifuge tests it was seen...

Geophysical imaging of the lacustrine sediments deposited in the La Calderilla Volcanic Caldera (Gran Canaria Island, Spain) for paleoclimate research

Science.gov (United States)

Himi, Mahjoub; Rodríguez-González, Alejandro; Criado, Constantino; Tapias, Josefina C.; Ravazzi, Cesare; Pérez-Torrado, Francisco; Casas, Albert

2016-04-01

The discovery of well-preserved maar structures is important not only for studying the eruptive activity and formation of volcanoes, but also for paleoclimate research, since laminated maar lake sediments may contain very detailed archives of climate and environmental history. Maars are a singular type of volcanic structure generated by explosive phreatomagmatic eruptions as a result of interaction between rising magma and groundwater. This kind of structures are characterised by circular craters, often filled with water and/or lacustrine sediments and surrounded by a ring of pyroclastic deposits.Recently a borehole was drilled at the bottom of La Calderilla volcanic complex which penetrated about 8.7 m in its sedimentary sequence and paleobotanical study has supplied the first evidence of paleoenvironmental evolution during the Holocene on the Gran Canaria Island. This survey, however, did not penetrate into the substrate because the total thickness of the sedimentary fill was unknown. Since the age of formation of La Calderilla volcanic complex based on K/Ar dating is about 85,000 years (Upper Pleistocene), the possibility of its sedimentary fill extends beyond of the Holocene is extremely attractive, since, for example, there are few paleoenvironmental data regarding how much the last glaciation that affected the Canary Islands. In these circumstances, the knowledge of the total thickness of the lacustrine sediments is crucial to design a deeper borehole in the next future. Therefore, the subsurface characterisation provided by geophysics is essential for determining thickness and geometry of the sedimentary filling. Multielectrode ERT method was used to obtain five 2-D resistivity cross-sections into La Calderilla volcanic caldera. An Iris Syscal Pro resistivity system with 48 electrodes connected to a 94 m long cable (2m electrode spacing) in Wenner-Schlumberger configuration for an investigation depth of about 20 m. Data quality (q Current injected was

Cyclic and heteroclinic flows near general static spherically symmetric black holes: semi-cyclic flows - addendum and corrigendum

Energy Technology Data Exchange (ETDEWEB)

Azreg-Ainou, Mustapha [Baskent University, Engineering Faculty, Ankara (Turkey)

2017-01-15

We present new accretion solutions of a polytropic perfect fluid onto an f(R)-gravity de Sitter-like black hole. We consider two f(R)-gravity models and obtain finite-period cyclic flows oscillating between the event and cosmological horizons as well as semi-cyclic critical flows executing a two-way motion from and back to the same horizon. Besides the generalizations and new solutions presented in this work, a corrigendum to Eur. Phys. J. C (2016) 76:280 is provided. (orig.)

HOST liner cyclic facilities

Science.gov (United States)

Schultz, D.

1983-01-01

The HOST Liner Cyclic Program is utilizing two types of test apparatus, rectangular box rigs and a full annular rig. To date two quartz lamp cyclic box rigs have been tested and a third is to begin testing in late October 1983. The box rigs are used to evaluate 5x8 inch rectangular linear samples. A 21 inch diameter outer liner simulator is also being built up for testing beginning in April 1984. All rigs are atmospheric rigs. The first box rig, a three 6-kVA lamp installation, was operated under adverse conditions to determine feasibility of using quartz lamps for cyclic testing. This work was done in December 1981 and looked promising. The second box rig, again using three 6-kVA lamps, was operated to obtain instrumentation durability information and initial data input to a Finite Element Model. This limited test program was conducted in August 1983. Five test plates were run. Instrumentation consisted of strain gages, thermocouples and thermal paint. The strain gages were found to fail at 1200 F as expected though plates were heated to 1700 F. The third box rig, containing four 6-kVA lamps, is in build up for testing to begin in late October 1983. In addition to 33 percent greater power input, this rig has provision for 400 F backside line cooling air and a viewing port suitable for IR camera viewing. The casing is also water cooled for extended durability.

Quality and petrographic characteristics of the lacustrine Ermenek coal (early Miocene), Turkey

Energy Technology Data Exchange (ETDEWEB)

Demirel, I.H.; Karayigit, A.I. [Hacettepe Univ., Beytepe-Ankara (Turkey). Dept. of Geological Engineering

1999-05-01

The early Miocene Yenimahalle Formation including alluvial-lacustrine sediments and a mineable coal steam with an average of 5 m in thickness rests unconformably upon the basement and is also unconformably overlain by marine limestones of the middle-late Miocene Mut Formation in the Ermenek coal basin. The coal basin in the present study has been subdivided into two areas, Canakci and Pamuklu-Tepebasi, which are separated by the basement and a fault, in order to determine coal properties in detail. The investigated subbituminous coals with an average of 0.40%Ro huminite reflectance often contain gastropod shells (Planorbidae) which commonly maintain the original aragonite and calcite composition. The coals have similar chemical properties and petrographic composition in the two areas, but their sulphur contents are clearly different. In the Canakci area the coals on an air-dried basis contain distinctly less total sulphur (avg. 1.3%) and organic sulphur contents (0.13--0.15%) than in the Pamuklu-Tepebasi area (avg. 4.5% and 4.25%, respectively). This difference is interpreted to be controlled by mire chemistry and sedimentation during peat formation.

Cyclic Stretch Alters Vascular Reactivity of Mouse Aortic Segments

Directory of Open Access Journals (Sweden)

Arthur Leloup

2017-10-01

Full Text Available Large, elastic arteries buffer the pressure wave originating in the left ventricle and are constantly exposed to higher amplitudes of cyclic stretch (10% than muscular arteries (2%. As a crucial factor for endothelial and smooth muscle cell function, cyclic stretch has, however, never been studied in ex vivo aortic segments of mice. To investigate the effects of cyclic stretch on vaso-reactivity of mouse aortic segments, we used the Rodent Oscillatory Tension Set-up to study Arterial Compliance (ROTSAC. The aortic segments were clamped at frequencies of 6–600 bpm between two variable preloads, thereby mimicking dilation as upon left ventricular systole and recoiling as during diastole. The preloads corresponding to different transmural pressures were chosen to correspond to a low, normal or high amplitude of cyclic stretch. At different time intervals, cyclic stretch was interrupted, the segments were afterloaded and isometric contractions by α1-adrenergic stimulation with 2 μM phenylephrine in the absence and presence of 300 μM L-NAME (eNOS inhibitor and/or 35 μM diltiazem (blocker of voltage-gated Ca2+ channels were measured. As compared with static or cyclic stretch at low amplitude (<10 mN or low frequency (0.1 Hz, cyclic stretch at physiological amplitude (>10 mN and frequency (1–10 Hz caused better ex vivo conservation of basal NO release with time after mounting. The relaxation of PE-precontracted segments by addition of ACh to stimulate NO release was unaffected by cyclic stretch. In the absence of basal NO release (hence, presence of L-NAME, physiological in comparison with aberrant cyclic stretch decreased the baseline tension, attenuated the phasic contraction by phenylephrine in the absence of extracellular Ca2+ and shifted the smaller tonic contraction more from a voltage-gated Ca2+ channel-mediated to a non-selective cation channel-mediated. Data highlight the need of sufficient mechanical activation of endothelial and

Evolutive masing model, cyclic plasticity, ageing and memory effects

International Nuclear Information System (INIS)

Sidoroff, F.

1987-01-01

Many models are proposed for the mechanical description of the cyclic behaviour of metals and used for structure analysis under cyclic loading. Such a model must include two basic features: Dissipative behaviour on each cycle (hysteresis loop); evolution of this behaviour during the material's life (cyclic hardening or softening, aging,...). However, if both aspects are present in most existing models, the balance between them may be quite different. Many metallurgical investigations have been performed about the microstructure and its evolution during cyclic loading, and it is desirable to introduce these informations in phenomenological models. The evolutive Masing model has been proposed to combine: the accuracy of hereditary models for the description of hysteresis on each cycle, the versatility of internal variables for the state description and evolution, a sufficient microstructural basis to make the interaction easier with microstructural investigations. The purpose of the present work is to discuss this model and to compare different evolution assumptions with respect to some memory effects (cyclic hardening and softening, multilevel tests, aging). Attention is limited to uniaxial, rate independent elasto-plastic behaviour

The enzymatic preparation of [α-32P]nucleoside triphosphates, cyclic [32P]AMP, and cyclic [32P]GMP

International Nuclear Information System (INIS)

Walseth, T.F.; Johnson, R.A.

1979-01-01

A method has been developed for the enzymatic preparation of α- 32 P-labelled ribo- and deoxyribonucleoside triphosphates, cyclic [ 32 P]AMP, and cyclic [ 32 P]GMP of high specific radioactivity and in high yield from 32 Psub(i). The method also enables the preparation of [γ- 32 P]ATP, [γ- 32 P]GTP, [γ- 32 P]ITP, and [γ- 32 P]-dATP of very high specific activity and in high yield. (Auth.)

Diagenetic variation at the lamina scale in lacustrine organic-rich shales: Implications for hydrocarbon migration and accumulation

Science.gov (United States)

Liang, Chao; Cao, Yingchang; Liu, Keyu; Jiang, Zaixing; Wu, Jing; Hao, Fang

2018-05-01

Lacustrine carbonate-rich shales are well developed within the Mesozoic-Cenozoic strata of the Bohai Bay Basin (BBB) of eastern China and across southeast Asia. Developing an understanding of the diagenesis of these shales is essential to research on mass balance, diagenetic fluid transport and exchange, and organic-inorganic interactions in black shales. This study investigates the origin and distribution of authigenic minerals and their diagenetic characteristics, processes, and pathways at the scale of lacustrine laminae within the Es4s-Es3x shale sequence of the BBB. The research presented in this study is based on thin sections, field emission scanning electron microscope (FESEM) and SEM-catholuminescence (CL) observations of well core samples combined with the use of X-ray diffraction (XRD), energy dispersive spectroscopy, electron microprobe analysis, and carbon and oxygen isotope analyses performed using a laser microprobe mass spectrometer. The dominant lithofacies within the Es4s-Es3x sequence are a laminated calcareous shale (LCS-1) and a laminated clay shale (LCS-2). The results of this study show that calcite recrystallization1 is the overarching diagenetic process affecting the LCS-1, related to acid generation from organic matter (OM) thermal evolution. This evolutionary transition is the key factor driving the diagenesis of this lithofacies, while the transformation of clay minerals is the main diagenetic attribute of the LCS-2. Diagenetic differences occur within different laminae and at variable locations within the same lamina level, controlled by variations in mineral composition and the properties of laminae interfaces. The diagenetic fluid migration scale is vertical and responses (dissolution and replacement) are limited to individual laminae, between zero and 100 μm in width. In contrast, the dominant migration pathway for diagenetic fluid is lateral, along the abrupt interfaces between laminae boundaries, which leads to the vertical

Identification of cyclic nucleotide gated channels using regular expressions

KAUST Repository

Zelman, Alice K.; Dawe, Adam Sean; Berkowitz, Gerald A.

2013-01-01

Cyclic nucleotide-gated channels (CNGCs) are nonselective cation channels found in plants, animals, and some bacteria. They have a six-transmembrane/one- pore structure, a cytosolic cyclic nucleotide-binding domain, and a cytosolic calmodulin

Cyclic plasticity models and application in fatigue analysis

Science.gov (United States)

Kalev, I.

1981-01-01

An analytical procedure for prediction of the cyclic plasticity effects on both the structural fatigue life to crack initiation and the rate of crack growth is presented. The crack initiation criterion is based on the Coffin-Manson formulae extended for multiaxial stress state and for inclusion of the mean stress effect. This criterion is also applied for the accumulated damage ahead of the existing crack tip which is assumed to be related to the crack growth rate. Three cyclic plasticity models, based on the concept of combination of several yield surfaces, are employed for computing the crack growth rate of a crack plane stress panel under several cyclic loading conditions.

The mycotoxin definition reconsidered towards fungal cyclic depsipeptides.

Science.gov (United States)

Taevernier, Lien; Wynendaele, Evelien; De Vreese, Leen; Burvenich, Christian; De Spiegeleer, Bart

2016-04-02

Currently, next to the major classes, cyclic depsipeptides beauvericin and enniatins are also positioned as mycotoxins. However, as there are hundreds more fungal cyclic depsipeptides already identified, should these not be considered as mycotoxins as well? The current status of the mycotoxin definition revealed a lack of consistency, leading to confusion about what compounds should be called mycotoxins. Because this is of pivotal importance in risk assessment prioritization, a clear and quantitatively expressed mycotoxin definition is proposed, based on data of widely accepted mycotoxins. Finally, this definition is applied to a set of fungal cyclic depsipeptides, revealing that some of these should indeed be considered as mycotoxins.

Holographic entanglement entropy and cyclic cosmology

Science.gov (United States)

Frampton, Paul H.

2018-06-01

We discuss a cyclic cosmology in which the visible universe, or introverse, is all that is accessible to an observer while the extroverse represents the total spacetime originating from the time when the dark energy began to dominate. It is argued that entanglement entropy of the introverse is the more appropriate quantity to render infinitely cyclic, rather than the entropy of the total universe. Since vanishing entanglement entropy implies disconnected spacetimes, at the turnaround when the introverse entropy is zero the disconnected extroverse can be jettisoned with impunity.

Effects of hypokinesia on cyclic nucleotides and hormonal regulation ...

African Journals Online (AJOL)

PTH), calcitonin (CT), cyclic nucleotides (cAMP, cGMP) and calcium in the blood of rats, while in urine - phosphate, calcium and cyclic nucleotides. Design: Laboratory based experiment. Setting: Laboratory in the Department of Biochemistry, ...

Evaluating cyclic fatigue of sealants during outdoor testing

Science.gov (United States)

R. Sam Williams; Steven Lacher; Corey Halpin; Christopher White

2009-01-01

A computer-controlled test apparatus (CCTA) and other instrumentation for subjecting sealant specimens to cyclic fatigue during outdoor exposure was developed. The CCTA enables us to use weather-induced conditions to cyclic fatigue specimens and to conduct controlled tests in-situ during the outdoor exposure. Thermally induced dimensional changes of an aluminum bar...

Cyclic inelastic deformation aspects of fatigue-crack-growth analysis

Energy Technology Data Exchange (ETDEWEB)

Leis, B.N.; Zahoor, A.

1980-01-01

This paper concentrates on a J-integral analysis of fatigue crack growth. Data on cyclic plasticity are analyzed showing that there are limitations to the usefulness of the deformation theory in applications to cyclic plasticity. 56 refs.

Investigation on effectiveness of a prefabricated vertical drain during cyclic loading

International Nuclear Information System (INIS)

Indraratna, B; Ni, J; Rujikiatkamjorn, C

2010-01-01

The effectiveness of prefabricated vertical drains (PVDs) in enhancing the stability of soft soils during cyclic loading was investigated using triaxial cyclic loading tests. Both undrained and with PVD tests were employed to study the associated excess pore pressure and accumulated strain under the repeated loading condition. The loading frequency and cyclic stress ratio have been chosen to be the variables which influence the performance of soft clays. The experimental results illustrate that with PVDs, the excess pore water pressure generation during cyclic loading decreases significantly. It is found that the excess pore water pressure build up depends on both loading frequency and cyclic stress ratio. The excess pore water pressure will increase when each of them is increased. Furthermore, when the loading frequency is 0.1 Hz, the ratio of coefficient of consolidation under cyclic loading to that under static loading is almost one. With the increasing loading frequency, this ratio increases accordingly.

Comparison of phosphorylation of ribosomal proteins from HeLa and Krebs II ascites-tumour cells by cyclic AMP-dependent and cyclic GMP-dependent protein kinases

DEFF Research Database (Denmark)

Issinger, O G; Beier, H; Speichermann, N

1980-01-01

Phosphorylation of eukaryotic ribosomal proteins in vitro by essentially homogeneous preparations of cyclic AMP-dependent protein kinase catalytic subunit and cyclic GMP-dependent protein kinase was compared. Each protein kinase was added at a concentration of 30nM. Ribosomal proteins were...... by the cyclic AMP-dependent enzyme. Between 0.1 and 0.2 mol of phosphate was incorporated/mol of these phosphorylated proteins. With the exception of protein S7, the same proteins were also major substrates for the cyclic GMP-dependent protein kinase. Time courses of the phosphorylation of individual proteins...... from the small and large ribosomal subunits in the presence of either protein kinase suggested four types of phosphorylation reactions: (1) proteins S2, S10 and L5 were preferably phosphorylated by the cyclic GMP-dependent protein kinase; (2) proteins S3 and L6 were phosphorylated at very similar rates...

Probabilistic Simulation of Combined Thermo-Mechanical Cyclic Fatigue in Composites

Science.gov (United States)

Chamis, Christos C.

2011-01-01

A methodology to compute probabilistically-combined thermo-mechanical fatigue life of polymer matrix laminated composites has been developed and is demonstrated. Matrix degradation effects caused by long-term environmental exposure and mechanical/thermal cyclic loads are accounted for in the simulation process. A unified time-temperature-stress-dependent multifactor-interaction relationship developed at NASA Glenn Research Center has been used to model the degradation/aging of material properties due to cyclic loads. The fast probability-integration method is used to compute probabilistic distribution of response. Sensitivities of fatigue life reliability to uncertainties in the primitive random variables (e.g., constituent properties, fiber volume ratio, void volume ratio, ply thickness, etc.) computed and their significance in the reliability-based design for maximum life is discussed. The effect of variation in the thermal cyclic loads on the fatigue reliability for a (0/+/-45/90)s graphite/epoxy laminate with a ply thickness of 0.127 mm, with respect to impending failure modes has been studied. The results show that, at low mechanical-cyclic loads and low thermal-cyclic amplitudes, fatigue life for 0.999 reliability is most sensitive to matrix compressive strength, matrix modulus, thermal expansion coefficient, and ply thickness. Whereas at high mechanical-cyclic loads and high thermal-cyclic amplitudes, fatigue life at 0.999 reliability is more sensitive to the shear strength of matrix, longitudinal fiber modulus, matrix modulus, and ply thickness.

Long-term behaviour of {sup 137}Cs in the lacustrine ecosystem of lake Viverone; Il comportamento a lungo termine del {sup 137}Cs nell`ecosistema lacustre del lago di Viverone

Energy Technology Data Exchange (ETDEWEB)

Spezzano, P.; Cerea, E.; Massironi, L.; Olivetta, A.; Bortoluzzi, S.; Nocente, M.; Berton, G. [ENEA, Centro Ricerche Saluggia, Vercelli (Italy). Dip. Ambiente

1998-12-31

For the evaluation of long term behaviour of {sup 137}Cs in a lacustrine ecosystem, for ten years after the Chernobyl nuclear accident several experimental studies have been conducted in the Viverone lake, a small, eutrophic, monomictic lake situated between Turin and Vercelli, in North-West Italy. Radiocaesium activities were measured in different components of the ecosystem, i.e. soil, water, sediment and biotas, and have been related with main environmental physico-chemical parameters. Changes in radiocaesium content with time provided information about transfer processes of this radionuclide into the lacustrine ecosystem. Levels of {sup 137}Cs in lake water after several years from deposition can be ascribed to the migration from catchment basin and to the remobilization from bottom sediments. However, experimental results do not allow to ascertain which of these two factors prevails over the other.

The Role of Cyclic Nucleotide Signaling Pathways in Cancer: Targets for Prevention and Treatment

Energy Technology Data Exchange (ETDEWEB)

Fajardo, Alexandra M.; Piazza, Gary A. [Drug Discovery Research Center, Mitchell Cancer Institute, University of South Alabama, 1660 Springhill Ave, Suite 3029, Mobile, AL 36604 (United States); Tinsley, Heather N., E-mail: htinsley@montevallo.edu [Department of Biology, Chemistry, and Mathematics, University of Montevallo, Station 6480, Montevallo, AL 35115 (United States)

2014-02-26

For more than four decades, the cyclic nucleotides cyclic AMP (cAMP) and cyclic GMP (cGMP) have been recognized as important signaling molecules within cells. Under normal physiological conditions, cyclic nucleotides regulate a myriad of biological processes such as cell growth and adhesion, energy homeostasis, neuronal signaling, and muscle relaxation. In addition, altered cyclic nucleotide signaling has been observed in a number of pathophysiological conditions, including cancer. While the distinct molecular alterations responsible for these effects vary depending on the specific cancer type, several studies have demonstrated that activation of cyclic nucleotide signaling through one of three mechanisms—induction of cyclic nucleotide synthesis, inhibition of cyclic nucleotide degradation, or activation of cyclic nucleotide receptors—is sufficient to inhibit proliferation and activate apoptosis in many types of cancer cells. These findings suggest that targeting cyclic nucleotide signaling can provide a strategy for the discovery of novel agents for the prevention and/or treatment of selected cancers.

Infinity-Norm Permutation Covering Codes from Cyclic Groups

OpenAIRE

Karni, Ronen; Schwartz, Moshe

2017-01-01

We study covering codes of permutations with the $\\ell_\\infty$-metric. We provide a general code construction, which uses smaller building-block codes. We study cyclic transitive groups as building blocks, determining their exact covering radius, and showing linear-time algorithms for finding a covering codeword. We also bound the covering radius of relabeled cyclic transitive groups under conjugation.

Influence of cyclic torsional preloading on cyclic fatigue resistance of nickel - titanium instruments.

Science.gov (United States)

Pedullà, E; Lo Savio, F; Boninelli, S; Plotino, G; Grande, N M; Rapisarda, E; La Rosa, G

2015-11-01

To evaluate the effect of different torsional preloads on cyclic fatigue resistance of endodontic rotary instruments constructed from conventional nickel-titanium (NiTi), M-Wire or CM-Wire. Eighty new size 25, 0.06 taper Mtwo instruments (Sweden & Martina), size 25, 0.06 taper HyFlex CM (Coltene/Whaledent, Inc) and X2 ProTaper Next (Dentsply Maillefer) were used. The Torque and distortion angles at failure of new instruments (n = 10) were measured, and 0% (n = 10), 25%, 50% and 75% (n = 20) of the mean ultimate torsional strength as preloading condition were applied according to ISO 3630-1 for each brand. The twenty files tested for every extent of preload were subjected to 20 or 40 torsional cycles (n = 10). After torsional preloading, the number of cycles to failure was evaluated in a simulated canal with 60° angle of curvature and 5 mm of radius of curvature. Data were analysed using two-way analysis of variance. The fracture surface of each fragment was examined with a scanning electron microscope (SEM). Data were analysed by two-way analyses of variance. Preload repetitions did not influence the cyclic fatigue of the three brands; however, the 25%, 50% and 75% torsional preloading significantly reduced the fatigue resistance of all instruments tested (P 0.05). Torsional preloads reduced the cyclic fatigue resistance of conventional and treated (M-wire and CM-wire) NiTi rotary instruments except for size 25, 0.06 taper HyFlex CM instruments with a 25% of torsional preloading. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Entire cyclic cohomology and modular theory

International Nuclear Information System (INIS)

Stoytchev, O.Ts.

1992-04-01

We display a close relationship between C* and W*-dynamical systems with KMS states on them and entire cyclic cohomology theory. We construct a character form which assigns to each such system (A, α, R) an even entire cyclic cocycle of the subalgebra A of differentiable (with respect to the given automorphism group) elements of A. We argue that the most interesting case is the von Neumann algebra one, where the automorphism group is determined uniquely by the faithful normal state on the algebra (the modular group) and where the character may provide important information about the algebra. (author). 11 refs

Paleo and present-day chemical weathering in lacustrine and riverine sediments in Northern Patagonia, Argentina

Energy Technology Data Exchange (ETDEWEB)

Roman Ross, Gabriela [Comision Nacional de Energia Atomica, San Carlos de Bariloche (Argentina). Centro Atomico Bariloche. Lab. de Analisis por Activacion Neutronica; Arribere, Maria A.; Guevara, Sergio Ribeiro [Universidad Nacional de Cuyo, XX (Argentina)

1996-07-01

Neutron activation analysis was used to study the abundance, distribution and fraction of REE (Rare Earth Elements) and diagnostic elements (Th, Co, Cr, Sc, Rb, Sr) in sediments from Mascardi lake and Upper Manso river. The local weathering patterns of this watershed show a strong influence of volcanic rocks with a selective mobilization of the more soluble elements. These patterns are very similar to those observed in a sedimentary lacustrine core from Mascardi lake. Paleolimnological record indicates a change in local fluxes of water and sediments, and an increase in organic matter content since the last full-glacial maximum. However, the chemical composition of the sedimentary inputs has not changed significantly during the last 14000 years. Our data support the hypothesis that present-day and Holocene chemical weathering have similar characteristics. All of the above conclusions are based on geochemical parameters only. (author)

Paleo and present-day chemical weathering in lacustrine and riverine sediments in Northern Patagonia, Argentina

International Nuclear Information System (INIS)

Roman Ross, Gabriela

1996-01-01

Neutron activation analysis was used to study the abundance, distribution and fraction of REE (Rare Earth Elements) and diagnostic elements (Th, Co, Cr, Sc, Rb, Sr) in sediments from Mascardi lake and Upper Manso river. The local weathering patterns of this watershed show a strong influence of volcanic rocks with a selective mobilization of the more soluble elements. These patterns are very similar to those observed in a sedimentary lacustrine core from Mascardi lake. Paleolimnological record indicates a change in local fluxes of water and sediments, and an increase in organic matter content since the last full-glacial maximum. However, the chemical composition of the sedimentary inputs has not changed significantly during the last 14000 years. Our data support the hypothesis that present-day and Holocene chemical weathering have similar characteristics. All of the above conclusions are based on geochemical parameters only. (author)

Riboflavin in cyclic vomiting syndrome: efficacy in three children.

Science.gov (United States)

Martinez-Esteve Melnikova, Anastasia; Schäppi, Michela G; Korff, Christian

2016-01-01

Cyclic vomiting syndrome is an episodic disorder considered to be a migraine variant. Riboflavin is efficient in the prophylactic treatment of migraines in adults. We describe the effectiveness and tolerance of riboflavin treatment in three children with cyclic vomiting syndrome. All of them fulfilled the diagnosis criteria for cyclic vomiting syndrome. They received prophylactic monotherapy with riboflavin for at least 12 months. Excellent response and tolerability was observed. Based on clinical observation in three cases, riboflavin may be an effective and safe prophylactic treatment for children with cyclic vomiting syndrome. CVS is one of the "childhood periodic syndromes" classified as a migraine subtype by the International Headache Society. Riboflavin is currently used as a prophylactic treatment in patients with migraine. Riboflavin may be an effective and safe prophylactic treatment for children with CVS. Increasing doses of riboflavin and long periods of prophylaxis may be needed in some children..

Insulin alters the target size of the peripheral cyclic AMP phosphodiesterase but not the integral cyclic GMP-stimulated cyclic AMP phosphodiesterase in liver plasma membranes

International Nuclear Information System (INIS)

Wallace, A.V.; Martin, B.R.; Houslay, M.D.

1990-01-01

Radiation inactivation of the two high affinity cyclic AMP phosphodiesterases (PDE) found in liver plasma membranes afforded an estimation of their molecular target sizes in situ. The activity of the peripheral plasma membrane PDE decayed as a single exponential with a target size corresponding to a monomer of circa 54 kDa. The integral, cyclic GMP-stimulated PDE decayed as a dimer of circa 125 kDa. Preincubation of plasma membranes with insulin (10nM), prior to irradiation, caused the target size of only the peripheral plasma membrane PDE to increase. We suggest that insulin addition causes the peripheral plasma membrane PDE to alter its coupling to an integral plasma membrane protein with a target size of circa 90 kDa

Sedimentary architecture of a sub-lacustrine debris fan: Eocene Dongying Depression, Bohai Bay Basin, east China

Science.gov (United States)

Liu, Jianping; Xian, Benzhong; Wang, Junhui; Ji, Youliang; Lu, Zhiyong; Liu, Saijun

2017-12-01

The sedimentary architectures of submarine/sublacustrine fans are controlled by sedimentary processes, geomorphology and sediment composition in sediment gravity flows. To advance understanding of sedimentary architecture of debris fans formed predominantly by debris flows in deep-water environments, a sub-lacustrine fan (Y11 fan) within a lacustrine succession has been identified and studied through the integration of core data, well logging data and 3D seismic data in the Eocene Dongying Depression, Bohai Bay Basin, east China. Six types of resedimented lithofacies can be recognized, which are further grouped into five broad lithofacies associations. Quantification of gravity flow processes on the Y11 fan is suggested by quantitative lithofacies analysis, which demonstrates that the fan is dominated by debris flows, while turbidity currents and sandy slumps are less important. The distribution, geometry and sedimentary architecture are documented using well data and 3D seismic data. A well-developed depositional lobe with a high aspect ratio is identified based on a sandstone isopach map. Canyons and/or channels are absent, which is probably due to the unsteady sediment supply from delta-front collapse. Distributary tongue-shaped debris flow deposits can be observed at different stages of fan growth, suggesting a lobe constructed by debrite tongue complexes. Within each stage of the tongue complexes, architectural elements are interpreted by wireline log motifs showing amalgamated debrite tongues, which constitute the primary fan elements. Based on lateral lithofacies distribution and vertical sequence analysis, it is proposed that lakefloor erosion, entrainment and dilution in the flow direction lead to an organized distribution of sandy debrites, muddy debrites and turbidites on individual debrite tongues. Plastic rheology of debris flows combined with fault-related topography are considered the major factors that control sediment distribution and fan

Study on elastic-plastic deformation analysis using a cyclic stress-strain curve

International Nuclear Information System (INIS)

Igari, Toshihide; Setoguchi, Katsuya; Yamauchi, Masafumi

1983-01-01

This paper presents the results of the elastic-plastic deformation analysis using a cyclic stress-strain curve with an intention to apply this method for predicting the low-cycle fatigue life. Uniaxial plastic cycling tests were performed on 2 1/4Cr-1Mo steel to investigate the correspondence between the cyclic stress-strain curve and the hysteresis loop, and also to determine what mathematical model should be used for analysis of deformation at stress reversal. Furthermore, a cyclic in-plane bending test was performed on a flat plate to clarify the validity of the cyclic stress-strain curve-based theoretical analysis. The results obtained are as follows: (1) The cyclic stress-strain curve corresponds nearly to the ascending curve of hysteresis loop scaled by a factor of 1/2 for both stress and strain. Therefore, the cyclic stress-strain curve can be determined from the shape of hysteresis loop, for simplicity. (2) To perform the elastic-plastic deformation analysis using the cyclic stress-strain curve is both practical and effective for predicting the cyclic elastic-plastic deformation of structures at the stage of advanced cycles. And Masing model can serve as a suitable mathematical model for such a deformation analysis. (author)

Anisotropic yield surfaces in bi-axial cyclic plasticity

International Nuclear Information System (INIS)

Rider, R.J.; Harvey, S.J.; Breckell, T.H.

1985-01-01

Some aspects of the behaviour of yield surfaces and work-hardening surfaces occurring in biaxial cyclic plasticity have been studied experimentally and theoretically. The experimental work consisted of subjecting thin-walled tubular steel specimens to cyclic plastic torsion in the presence of sustained axial loads of various magnitudes. The experimental results show that considerable anisotropy is induced when the cyclic shear strains are dominant. Although the true shapes of yield and work-hardening surfaces can be very complex, a mathematical model is presented which includes both anisotropy and Bauschinger effects. The model is able to qualitatively predict the deformation patterns during a cycle of applied plastic shear strain for a range of sustained axial stresses and also indicate the material response to changes in axial stress. (orig.)

Degradation forecast for PEMFC cathode-catalysts under cyclic loads

Science.gov (United States)

Moein-Jahromi, M.; Kermani, M. J.; Movahed, S.

2017-08-01

Degradation of Fuel Cell (FC) components under cyclic loads is one of the biggest bottlenecks in FC commercialization. In this paper, a novel experimental based algorithm is presented to predict the Catalyst Layer (CL) performance loss during cyclic load. The algorithm consists of two models namely Models 1 and 2. The Model 1 calculates the Electro-Chemical Surface Area (ECSA) and agglomerate size (e.g. agglomerate radius, rt,agg) for the catalyst layer under cyclic load. The Model 2 is the already-existing model from our earlier studies that computes catalyst performance with fixed structural parameters. Combinations of these two Models predict the CL performance under an arbitrary cyclic load. A set of parametric/sensitivity studies is performed to investigate the effects of operating parameters on the percentage of Voltage Degradation Rate (VDR%) with rank 1 for the most influential one. Amongst the considered parameters (such as: temperature, relative humidity, pressure, minimum and maximum voltage of the cyclic load), the results show that temperature and pressure have the most and the least influences on the VDR%, respectively. So that, increase of temperature from 60 °C to 80 °C leads to over 20% VDR intensification, the VDR will also reduce 1.41% by increasing pressure from 2 atm to 4 atm.

Quality and petrographic characteristics of the Lacustrine Ermenek Coal (Early Miocene), Turkey

Energy Technology Data Exchange (ETDEWEB)

Demirel, I.H.; Karayigit, A.I.

1999-04-15

The early Miocene Yenimahalle Formation including alluvial-lacustrine sediments and a mineable coal seam with an average of 5 m in thickness rests unconformably upon the basement and is also unconformably overlain by marine limestones of the middle-late Miocene Mut Formation in the Ermenek coal basin. The coal basin in the present study has been subdivided into two areas, Canakci and Pamuklu-Tepebasi, which are separated by the basement and a fault, in order to determine coal properties in detail. The investigated subbituminous coals with an average of 0.40% Ro huminite reflectance often contain gastropod shells (Planorbidae) which commonly maintain the original aragonite and calcite composition. The coals have similar chemical properties and petrographic composition in the two areas, but their sulphur contents are clearly different. In the Canakci area the coals on an air-dried basis contain distinctly less total sulphur (avg. 1.3%) and organic sulphur contents (0.13 0.15%) than in the Pamuklu-Tepebasi area (avg. 4.5% and 4.25%, respectively). This difference is interpreted to be controlled by mire chemistry and sedimentation during peat formation. (author)

Characterization of cyclical phases in the manufacturing industry in Spain

OpenAIRE

Sala, Mercè; Torres, Teresa; Farré, Mariona

2014-01-01

Purpose: The purpose of this paper is to characterize the cyclical phases of the manufacturing industry in Spain and detect which industries have more influence on the Spanish business cycle. We assume that economic growth is a priority; we are going to determine which industries have a more/less appropriate cyclical behavior according this priority. We analyze if the industries with better cyclical behavior are the ones that achieve greater co-movement with the business cycle of the Spanish...

Cyclic Creep Behavior of Modified 9Cr-1Mo Steel at 600 .deg. C

International Nuclear Information System (INIS)

Kim, Woo Gon; Kim, Dae Whan; Jang, Jin Sung; Park, Jae Young

2012-01-01

Cyclic deformation behavior is important in practice because high-temperature structural components are exposed under the cyclic conditions of repeated loading. In static creep (SC), the response of the material is simple as a static state of monotonic loading. However, in cyclic creep (CC), it is complex as dynamic loading. Cyclic creep data have been rarely reported until now. In particular, it is not understood well whether cyclic creep will accelerate or retard the creep rate compared with static creep, because it is not only the plastic deformation under cyclic loading is drastically different from monotonic loading, but also the cyclic response is dependent on the cycling frequency, stress range, stress ratio, and hold periods of cycling. Therefore, it is necessary to clarify the cyclic creep behavior influencing the creep deformation and fracture process. In this study, a series of cyclic creep tests was carried out using magnitudes of stress range of constant stress ratio (R=0.1) under continuous tension-tension loading cycles at a hold time of 10 minutes. Cyclic curves were monitored and obtained with time variations, and the properties of the cyclic creep tests were compared with those of static creep tests. The fracture microstructures were observed and analyzed

METHODOLOGICAL ASPECTS OF ECONOMIC EVENTS CYCLICITY METHOD CONSIDERATION

Directory of Open Access Journals (Sweden)

Yaskova Natalia Yur'ievna

2017-07-01

Full Text Available The cyclicity of economic phenomena is not only their immanent property but also the subject of economic analysis. The modern way of making managerial decisions requires analysis of a number of cycles that fill any kind of activity. Accounting and reconciliation of construction, design, investment, purchasing, reproduction, leasing and other cycles is important for the investment and construction sector, both from the point of view of the need for their synchronization and from the position of determining trends in sectoral development. The analysis has showed that three main types of development are characteristic for investment and construction activity. Increasing intensity is inherent in a high level of cyclic synchronization. The degradation trend arises as a result of mismatched cycles. The stabilization character is inherent in the regular modes of maintaining the established proportions and cyclical inter-conformity. The study of the cyclical nature of investment and building processes is impossible without understanding their co-ordination. The principles of synchronization and subordination of the cycles should be used not only for the construction of cost-effective systems but also for the development of management tools.

Cyclic deformation and fatigue behaviors of Hadfield manganese steel

Energy Technology Data Exchange (ETDEWEB)

Kang, J. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Zhang, F.C., E-mail: zfc@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Long, X.Y. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Lv, B. [School of Environmental and Chemical Engineering, Yanshan University, Qinhuangdao 066004 (China)

2014-01-03

The cyclic deformation characteristics and fatigue behaviors of Hadfield manganese steel have been investigated by means of its ability to memorize strain and stress history. Detailed studies were performed on the strain-controlled low cycle fatigue (LCF) and stress-controlled high cycle fatigue (HCF). Initial cyclic hardening to saturation or peak stress followed by softening to fracture occurred in LCF. Internal stress made the dominant contribution to the fatigue crack propagation until failure. Effective stress evolution revealed the existence of C–Mn clusters with short-range ordering in Hadfield manganese steel and demonstrated that the interaction between C atoms in the C–Mn cluster and dislocation was essential for its cyclic hardening. The developing/developed dislocation cells and stacking faults were the main cyclic deformation microstructures on the fractured sample surface in LCF and HCF, which manifested that fatigue failure behavior of Hadfield manganese steel was induced by plastic deformation during strain-controlled or stress-controlled testing.

The Synthesis of Unsubstituted Cyclic Imides Using Hydroxylamine under Microwave Irradiation

Directory of Open Access Journals (Sweden)

Yousef Hijji

2008-01-01

Full Text Available Unsubstituted cyclic imides were synthesized from a series of cyclic anhydrides,hydroxylamine hydrochloride (NH2OH·HCl, and 4-N,N-dimethylamino-pyridine (DMAP,base catalyst under microwave irradiation in monomode and multimode microwaves. Thisnovel microwave synthesis produced high yields of the unsubstituted cyclic imides forboth the monomode (61 - 81% and multimode (84 - 97% microwaves.

Classifying spaces with virtually cyclic stabilizers for linear groups

DEFF Research Database (Denmark)

Degrijse, Dieter Dries; Köhl, Ralf; Petrosyan, Nansen

2015-01-01

We show that every discrete subgroup of GL(n, ℝ) admits a finite-dimensional classifying space with virtually cyclic stabilizers. Applying our methods to SL(3, ℤ), we obtain a four-dimensional classifying space with virtually cyclic stabilizers and a decomposition of the algebraic K-theory of its...

Luminescence dating of the lacustrine record of Vršac (Carpathian Basin, Serbia) - implications for a palaeoenvironmetal reconstruction

Science.gov (United States)

Klasen, N.; Zeeden, C.; Markovic, S.; Fischer, P.; Lehmkuhl, F.; Schulte, P.; Bösken, J.; Hambach, U.; Vött, A.

2017-12-01

The Carpathian Basin is one of the key areas to investigate the influence of the continental, Mediterranean and Atlantic climate interaction over Europe. The available Upper Pleistocene and Holocene geoarchives in the region are mainly loess-paleosol records. Long lacustrine records are sparse and do not always span the whole last glacial cycle. In the area around Vršac, we drilled a 10 m core to contribute to the palaeoenvironmental reconstruction of the Carpathian Basin. Electrical Resistivity Tomography (ERT) was used to find the best-suited drilling location. We applied luminescence and radiocarbon dating, because a robust chronology is important for the interpretation of the sedimentary record. Pulsed OSL measurements were carried out to identify the best sampling positions. We expect runoff from the catchment being the main source of the lacustrine sediments, because coarse fluvial input is absent. Knowledge about the depositional conditions is important in luminescence dating to evaluate partial bleaching prior to deposition, which may cause age overestimation. Therefore, we compared infrared stimulated luminescence (IRSL) signals with post infrared infrared stimulated luminescence (pIRIR) signals, which bleach at different rates. Estimation of a representative water content has major influence on the age estimate, but remains challenging in luminescence dating. We measured the present day water content as well as the saturation water content, to account for variations over time. Luminescence and radiocarbon ages differ greatly from each other. According to the laboratory experiments, luminescence dating was reliable and we conclude that radiocarbon ages were underestimated because of an intrusion of younger organic material. The initial results demonstrated the potential of the drill core. Integrating more proxy data will be useful to enhance the importance of the geoarchive at Vršac for a better understanding of the last glacial cycle in the Carpathian

Palaeoenvironmental assessment of Westphalian fluvio-lacustrine deposits of Lorraine (France) using a combination of organic geochemistry and sedimentology

International Nuclear Information System (INIS)

Fleck, Stephanie; Michels, Raymond; Izart, Alain; Elie, Marcel; Landais, Patrick

2001-01-01

The quality and the quantity of organic carbon preserved in modern and ancient terrestrial sediments is the result of a complex interactions of sedimentological factors, such as in-situ productivity, allochtonous supply of organic matter, oxidation processes, biodegradation and sediment accumulation rates. The study aims at utilizing multidisciplinary information in order to characterize the palaeoenvironment in Westphalian fluvio-lacustrine deposits of the Lorraine Coal Basin (NE France). In this basin, the lack of outcrops is the major difficulty. To compensate for this problem, sedimentology, and molecular geochemistry are combined in order to significantly improve the palaeoenvironmental assessment of the area. Geochemical analyses and sedimentology have been carried out on several core samples of the Saulcy drill hole to evaluate local palaeoenvironmental variability. The lithofacies associations in the Upper Carboniferous of the Lorraine basin suggest an alluvial plain environment without marine incursions. Sedimentological interpretations of the core, as well as comparison with sedimentological models, suggests the recognition of different depositional environments from braided and/or meandering rivers to swamp and lakes. The organic geochemistry is focussed on the recognition of aliphatic hydrocarbons and especially on molecular biomarkers, which provide valuable information about the original organic matter and the transformations that took place during sedimentation and diagenesis. In the Lorraine basin, the botanical variability is high and clearly related to the position of the vegetation communities in the fluvial system. The biomarkers (e.g., diterpanes, steranes) show variations, which can be related to the diversity of this ecosystem. In this study, a reinterpretation of the environmental zonation in the sterane ternary diagram adapted to a fluvio-lacustrine sedimentology is proposed. The correlation between sedimentological and geochemical

Geomorphic Drainage Capture Recorded by Oxygen Isotopes of Green River Formation Lacustrine Mudstone, Eocene, Wyoming

Science.gov (United States)

Doebbert, A. C.; Booth, A. L.; Carroll, A.; Chamberlain, C.; Rhodes, M.

2005-12-01

The isotopic composition of cement and other meteoric precipitates are increasingly being used to interpret orogenic uplift histories, based on the relationship between altitude and rainwater δ18O. However, other variables such as changing regional drainage patterns may also affect the downstream composition of surface waters, especially when multiple drainages commingle in a lake. The Green River Formation contains some of the best documented lacustrine deposits in the world, making it ideal for examining such issues. Carbonate mudstone in balanced-fill facies of the lower LaClede Bed averages 3.41‰ (PDB), and records a deep, saline to brackish lake that fluctuated near its sill. In contrast, overfilled facies of the upper LaClede Bed record a freshwater lake, and δ18O reaches values as low as -9.72‰. This transition occurred shortly after deposition of the Analcite Tuff at 48.94 ± 0.12 Ma (Smith et al., 2003), and was geologically abrupt. Based on 40Ar/39Ar-calibrated sediment accumulation rates it required no more than 200-300 ky. An almost identical transition occurs in two cores separated by about 30 km, making local diagenesis an unlikely cause. The magnitude of δ18O change is similar to that in some uplift studies, but its rapidity virtually excludes uplift as a controlling mechanism. Instead, we propose that both the change in sedimentation and the sharp decrease in δ18O are the result of a drainage capture event. The addition of a new drainage to the basin may have adjusted isotopic values in two ways: by introducing runoff with relatively low δ18O, and by decreasing residence time (and therefore evaporation) of lake water. Decreasing 87Sr/86Sr across the same transition suggests that the newly added waters may have been sourced from rising volcanic topography to the north in the Absaroka province. Although this rising topography allows for the possibility of some uplift component, the rate of change in lacustrine δ18O is consistent with

Constitutive model and electroplastic analysis of structures under cyclic loading

International Nuclear Information System (INIS)

Wang, X.; Lei, Y; Du, Q.

1989-01-01

Many engineering structures in nuclear reactors, thermal power stations, chemical plants and aerospace vehicles are subjected to cyclic mechanic-thermal loading, which is the main cause of structural fatigue failure. Over the past twenty years, designers and researchers have paid great attention to the research on life prediction and elastoplastic analysis of structures under cyclic loading. One of the key problems in elastoplastic analysis is to construct a reasonable constitutive model for cyclic plasticity. In the paper, the constitutive equations are briefly outlined. Then, the model is implemented in a finite element code to predict the response of cyclic loaded structural components such as a double-edge-notched plate, a grooved bar and a nozzle in spherical shell. Numerical results are compared with those from other theories and experiments

Modeling Cyclic Variation of Intracranial Pressure

National Research Council Canada - National Science Library

Daley, M

2001-01-01

...) recording during mechanical ventilation are due to cyclic extravascular compressional modulation primarily of the cerebral venous bed, an established isovolumetric model of cerebrospinal fluid...

Prognosis of Cyclic Vomiting Syndrome

Directory of Open Access Journals (Sweden)

J. Gordon Millichap

2016-03-01

Full Text Available Investigators from Teikyo University School of Medicine, Tokyo, Japan, evaluated the clinical features, prognosis, and prophylaxis of cyclic vomiting syndrome and the relationship between the syndrome and levels of adrenocorticotropic/antidiuretic hormones (ACTH/ADH.

Existence and Convergence of Best Proximity Points for Semi Cyclic Contraction Pairs

Directory of Open Access Journals (Sweden)

Balwant Singh Thakur

2014-02-01

Full Text Available In this article, we introduce the notion of a semi cyclic ϕ-contraction pair of mappings, which contains semi cyclic contraction pairs as a subclass. Existence and convergence results of best proximity points for semi cyclic ϕ- contraction pair of mappings are obtained.

A Practical Beginner's Guide to Cyclic Voltammetry

Science.gov (United States)

Elgrishi, Noémie; Rountree, Kelley J.; McCarthy, Brian D.; Rountree, Eric S.; Eisenhart, Thomas T.; Dempsey, Jillian L.

2018-01-01

Despite the growing popularity of cyclic voltammetry, many students do not receive formalized training in this technique as part of their coursework. Confronted with self-instruction, students can be left wondering where to start. Here, a short introduction to cyclic voltammetry is provided to help the reader with data acquisition and…

Biosynthesis of cyclic 2,3-diphosphoglycerate. Isolation and characterization of 2-phosphoglycerate kinase and cyclic 2,3-diphosphoglycerate synthetase from Methanothermus fervidus.

Science.gov (United States)

Lehmacher, A; Vogt, A B; Hensel, R

1990-10-15

Starting from 2-phosphoglycerate the biosynthesis of cDPG comprises two steps: (i) the phosphorylation of 2-phosphoglycerate to 2,3-diphosphoglycerate and (ii) the intramolecular cyclization to cyclic 2,3-diphosphoglycerate. The involved enzymes, 2-phosphoglycerate kinase and cyclic 2,3-diphosphoglycerate synthetase, were purified form Methanothermus fervidus. Their molecular and catalytic properties were characterized.

Topological chaos, braiding and bifurcation of almost-cyclic sets.

Science.gov (United States)

Grover, Piyush; Ross, Shane D; Stremler, Mark A; Kumar, Pankaj

2012-12-01

In certain two-dimensional time-dependent flows, the braiding of periodic orbits provides a way to analyze chaos in the system through application of the Thurston-Nielsen classification theorem (TNCT). We expand upon earlier work that introduced the application of the TNCT to braiding of almost-cyclic sets, which are individual components of almost-invariant sets [Stremler et al., "Topological chaos and periodic braiding of almost-cyclic sets," Phys. Rev. Lett. 106, 114101 (2011)]. In this context, almost-cyclic sets are periodic regions in the flow with high local residence time that act as stirrers or "ghost rods" around which the surrounding fluid appears to be stretched and folded. In the present work, we discuss the bifurcation of the almost-cyclic sets as a system parameter is varied, which results in a sequence of topologically distinct braids. We show that, for Stokes' flow in a lid-driven cavity, these various braids give good lower bounds on the topological entropy over the respective parameter regimes in which they exist. We make the case that a topological analysis based on spatiotemporal braiding of almost-cyclic sets can be used for analyzing chaos in fluid flows. Hence, we further develop a connection between set-oriented statistical methods and topological methods, which promises to be an important analysis tool in the study of complex systems.

Micromechanics of soil responses in cyclic simple shear tests

Directory of Open Access Journals (Sweden)

Cui Liang

2017-01-01

Full Text Available Offshore wind turbine (OWT foundations are subjected to a combination of cyclic and dynamic loading arising from wind, wave, rotor and blade shadowing. Under cyclic loading, most soils change their characteristics including stiffness, which may cause the system natural frequency to approach the loading frequency and lead to unplanned resonance and system damage or even collapse. To investigate such changes and the underlying micromechanics, a series of cyclic simple shear tests were performed on the RedHill 110 sand with different shear strain amplitudes, vertical stresses and initial relative densities of soil. The test results showed that: (a Vertical accumulated strain is proportional to the shear strain amplitude but inversely proportional to relative density of soil; (b Shear modulus increases rapidly in the initial loading cycles and then the rate of increase diminishes and the shear modulus remains below an asymptote; (c Shear modulus increases with increasing vertical stress and relative density, but decreasing with increasing strain amplitude. Coupled DEM simulations were performed using PFC2D to analyse the micromechanics underlying the cyclic behaviour of soils. Micromechanical parameters (e.g. fabric tensor, coordination number were examined to explore the reasons for the various cyclic responses to different shear strain amplitudes or vertical stresses. Both coordination number and magnitude of fabric anisotropy contribute to the increasing shear modulus.

Constraining cyclic peptides to mimic protein structure motifs

DEFF Research Database (Denmark)

Hill, Timothy A.; Shepherd, Nicholas E.; Diness, Frederik

2014-01-01

peptides can have protein-like biological activities and potencies, enabling their uses as biological probes and leads to therapeutics, diagnostics and vaccines. This Review highlights examples of cyclic peptides that mimic three-dimensional structures of strand, turn or helical segments of peptides...... and proteins, and identifies some additional restraints incorporated into natural product cyclic peptides and synthetic macrocyclic pepti-domimetics that refine peptide structure and confer biological properties....

Organic sedimentation in modern lacustrine systems: A case study from Lake Malawi, East Africa

Science.gov (United States)

Ellis, Geoffrey S.; Barry J. Katz,; Christopher A. Scholz,; Peter K. Swart,

2015-01-01

This study examines the relationship between depositional environment and sedimentary organic geochemistry in Lake Malawi, East Africa, and evaluates the relative significance of the various processes that control sedimentary organic matter (OM) in lacustrine systems. Total organic carbon (TOC) concentrations in recent sediments from Lake Malawi range from 0.01 to 8.80 wt% and average 2.83 wt% for surface sediments and 2.35 wt% for shallow core sediments. Hydrogen index (HI) values as determined by Rock-Eval pyrolysis range from 0 to 756 mg HC g−1 TOC and average 205 mg HC g−1 TOC for surface sediments and 228 mg HC g−1 TOC for shallow core samples. On average, variations in primary productivity throughout the lake may account for ~33% of the TOC content in Lake Malawi sediments (as much as 1 wt% TOC), and have little or no impact on sedimentary HI values. Similarly, ~33% to 66% of the variation in TOC content in Lake Malawi sediments appears to be controlled by anoxic preservation of OM (~1–2 wt% TOC), although some component of the water depth–TOC relationship may be due to physical sediment transport processes. Furthermore, anoxic preservation has a minimal effect on HI values in Lake Malawi sediments. Dilution of OM by inorganic sediment may account for ~16% of variability in TOC content in Lake Malawi sediments (~0.5 wt% TOC). The effect of inputs of terrestrial sediment on the organic character of surface sediments in these lakes is highly variable, and appears to be more closely related to the local depositional environment than the regional flux of terrestrial OM. Total nitrogen and TOC content in surface sediments collected throughout the lake are found to be highly correlated (r2 = 0.95), indicating a well-homogenized source of OM to the lake bottom. The recurring suspension and deposition of terrestrial sediment may account for significant amounts of OM deposited in offshore regions of the lake. This process effectively separates denser

The Cyclic Stress-Strain Curve of Polycrystals

DEFF Research Database (Denmark)

Pedersen, Ole Bøcker; Rasmussen, K. V.; Winter, A. T.

1982-01-01

The internal stresses implied by the Sachs model are estimated for individual PSBs at low plastic strain amplitudes and for homogeneously sheared grains at higher plastic strain amplitudes. The analysis shows that the Sachs model can account semi-quantitatively for experimentally measured cyclic...... stress-strain curves for copper. A similar approximative analysis of the Taylor model cannot account for the data. An interesting feature of the Sachs model is that, although it is assumed that the flow condition is entirely controlled by the PSBs. the predicted cyclic stress-strain curve displays...

Ekpyrotic and cyclic cosmology

International Nuclear Information System (INIS)

Lehners, Jean-Luc

2008-01-01

Ekpyrotic and cyclic cosmologies provide theories of the very early and of the very late universe. In these models, the big bang is described as a collision of branes - and thus the big bang is not the beginning of time. Before the big bang, there is an ekpyrotic phase with equation of state w=P/(ρ) >>1 (where P is the average pressure and ρ the average energy density) during which the universe slowly contracts. This phase resolves the standard cosmological puzzles and generates a nearly scale-invariant spectrum of cosmological perturbations containing a significant non-Gaussian component. At the same time it produces small-amplitude gravitational waves with a blue spectrum. The dark energy dominating the present-day cosmological evolution is reinterpreted as a small attractive force between our brane and a parallel one. This force eventually induces a new ekpyrotic phase and a new brane collision, leading to the idea of a cyclic universe. This review discusses the detailed properties of these models, their embedding in M-theory and their viability, with an emphasis on open issues and observational signatures

Climatic and lacustrine morphometric controls of diatom paleoproductivity in a tropical Andean lake

Science.gov (United States)

Bao, R.; Hernández, A.; Sáez, A.; Giralt, S.; Prego, R.; Pueyo, J. J.; Moreno, A.; Valero-Garcés, B. L.

2015-12-01

The coupling of lake dynamics with catchment biogeochemistry is considered the key element controlling primary production in mountain lakes at time scales of a few decades to millennia, yet little is known on the impacts of the morphometry of lakes throughout their ontogeny. As Lake Chungará (Central Andean Altiplano, northern Chile) experienced long-term lake-level fluctuations that strongly modified its area:volume ratio, it is an ideal system for exploring the relative roles that long-term climatic shifts and lake morphometry play on biosiliceous lacustrine productivity. In this paper, we review previous data on the percent contents of total organic carbon, total inorganic carbon, total nitrogen, total biogenic silica, isotopic composition of organic matter, carbonates, and diatom frustules, as well as data on the abundance of the chlorophycean Botryococcus braunii in this lake for the period 12,400-1300 cal yr BP. We also include new data on organic carbon and biogenic silica mass accumulation rates and the diatom assemblage composition of an offshore core dated using 14C and U/Th. Biosiliceous productivity in Lake Chungará was influenced by shifts in allochthonous nutrient inputs related to variability in precipitation. Humid phases dated at approx. 12,400 to 10,000 and 9600 to 7400 cal yr BP coincide with periods of elevated productivity, whereas decreases in productivity were recorded during arid phases dated at approx. 10,000 to 9600 and 7400 to 3550 cal yr BP (Andean mid-Holocene Aridity Period). However, morphometry-related in-lake controls led to a lack of a linear response of productivity to precipitation variability. During the late Glacial to early Holocene, lowstands facilitated complete water column mixing, prompting episodic massive blooms of a large centric diatom, Cyclostephanos cf. andinus. Thus, moderate productivity could be maintained, regardless of aridity, by this phenomenon of morphometric eutrophy during the early history of the lake

Is the Fiscal Policy of the Czech Republic Pro-cyclical?

Directory of Open Access Journals (Sweden)

Martin Rolák

2015-01-01

Full Text Available The main goal of this paper is to analyse whether the fiscal policy of the Czech Republic is anti-cyclical. This analysis is carried out through decomposing the government’s balance into its cyclical and structural part. The first differences of the structural part are then put in relation to the output gap to determine whether the fiscal policy is pro- or anti-cyclical. Moreover, the correlation of government expenditures and revenues with the business cycle is also subject of our analysis. We also examine whether the fiscal rules which the Czech Republic would have to adhere to once it enters the euro area limit fiscal policy as a stabilizing mechanism.The paper concludes that the fiscal policy in the Czech Republic was for the most part rather of a random character than anti-cyclical during the examined period 1998–2013. This conclusion has two implications. Firstly, there is still room for improvement in fully and consistently utilizing fiscal policy to stabilise the Czech economy throughout economic cycles. Secondly, fiscal rules would not limit the Czech government to practice anti-cyclical fiscal policy if they have been implemented since 1998.

Cyclic compressive creep-elastoplastic behaviors of in situ TiB_2/Al-reinforced composite

International Nuclear Information System (INIS)

Zhang, Qing; Zhang, Weizheng; Liu, Youyi; Guo, BingBin

2016-01-01

This paper presents a study on the cyclic compressive creep-elastoplastic behaviors of a TiB_2-reinforced aluminum matrix composite (ZL109) at 350 °C and 200 °C. According to the experimental results, under cyclic elastoplasticity and cyclic coupled compressive creep-elastoplasticity, the coupled creep will cause changes in isotropic stress and kinematic stress. Isotropic stress decreases with coupled creep, leading to cyclic softening. Positive kinematic stress, however, increases with coupled creep, leading to cyclic hardening. Transmission electron microscopy (TEM) observations of samples under cyclic compressive creep-elastoplasticity with different temperatures and strain amplitudes indicate that more coupled creep contributes to more subgrain boundaries but fewer intracrystalline dislocations. Based on the macro tests and micro observations, the micro mechanism of compressive creep's influence on cyclic elastoplasticity is elucidated. Dislocations recovering with coupled creep leads to isotropic softening, whereas subgrain structures created by coupled creep lead to kinematic hardening during cyclic deformation.

A Note on the G-Cyclic Operators over a Bounded Semigroup

International Nuclear Information System (INIS)

Hamada, Nuha H.; Jamil, Zeana Z.

2010-08-01

Let H be an infinite-dimensional separable complex Hilbert space, and B(H) be the Banach algebra of all linear bounded operators on H. Let S be a multiplication semigroup of C with 1, an operator T element of B(H) is called G-cyclic operator over S if there is a vector x in H such that {αT n x|α element of S, n ≥ 0} is dense in H. In this case x is called a G-cyclic vector for T over S. If T is G-cyclic operator and S = {1} then T is a hypercyclic operator. In this paper, we study the spectral properties of a G-cyclic operators over a bounded S under the condition that zero is not in the closure of S. We show that the class of all G-cyclic operators is contained in the norm-closure of the class of all hypercyclic operators. (author)

Quantum Codes From Cyclic Codes Over The Ring R 2

International Nuclear Information System (INIS)

Altinel, Alev; Güzeltepe, Murat

2016-01-01

Let R 2 denotes the ring F 2 + μF 2 + υ 2 + μυ F 2 + wF 2 + μwF 2 + υwF 2 + μυwF 2 . In this study, we construct quantum codes from cyclic codes over the ring R 2 , for arbitrary length n, with the restrictions μ 2 = 0, υ 2 = 0, w 2 = 0, μυ = υμ, μw = wμ, υw = wυ and μ (υw) = (μυ) w. Also, we give a necessary and sufficient condition for cyclic codes over R 2 that contains its dual. As a final point, we obtain the parameters of quantum error-correcting codes from cyclic codes over R 2 and we give an example of quantum error-correcting codes form cyclic codes over R 2 . (paper)

Separation of isotopes by cyclical processes

International Nuclear Information System (INIS)

Hamrin, C.E. Jr.; Weaver, K.

1976-01-01

Various isotopes of hydrogen are separated by a cyclic sorption process in which a gas stream containing the isotopes is periodically passed through a high pressure column containing a palladium sorbent. A portion of the product from the high pressure column is passed through a second column at lower pressure to act as a purge. Before the sorbent in the high pressure column becomes saturated, the sequence is reversed with the stream flowing through the former low-pressure column now at high pressure, and a portion of the product purging the former high pressure column now at low pressure. The sequence is continued in cyclic manner with the product being enriched in a particular isotope

Cyclic operation of power plant; Cyklisk drift av kraftvaermeverk

Energy Technology Data Exchange (ETDEWEB)

Storesund, Jan

2007-12-15

The great majority of power plants are designed for base load operation with a relatively small number of starts and stops per year. Therefore, there has been no need to consider fatigue at design. Over the last few years operation with more frequent starts and stops exists as a consequence of swinging electricity prices that has become common. This involves significantly higher frequency of damages; not least fatigue relates damages, and the number of severe failures in components that never before have had damage problems may increase as well. In the present work the different types of component that may suffer from cyclic operation related damage are gathered by a literature survey and described as follows: - where and how the damages comes up, - constructions that should be avoided, - non-destructive testing (NDT) for damage that may come up under cyclic operation, - calculation and assessment of integrity of critical components - areas where continued research would be valuable. Recommendations have been put together to be used to prevent cyclic operation related damage and to detect it in time. The target group for this study is i) plant owners of plants where cyclic operation is or may be present, ii) researchers in the area, and, iii) inspectors and NDT-operators. There are quite a number of components where cyclic operation has been found to significantly influence the lift time. Some of these components are described in many papers whereas occasional papers have been found for others. The amount of information that is possible to get for a certain component is likely related to its significance for cyclic operation damage. The most frequently reported problem is ligament cracking of high temperature headers. Other components where extensive studies have been done are: wall panels, creep-fatigue loaded welds and turbine components

Recent progress on weight distributions of cyclic codes over finite fields

Directory of Open Access Journals (Sweden)

Hai Q. Dinh

2015-01-01

Full Text Available Cyclic codes are an interesting type of linear codes and have wide applications in communication and storage systems due to their efficient encoding and decoding algorithms. In coding theory it is often desirable to know the weight distribution of a cyclic code to estimate the error correcting capability and error probability. In this paper, we present the recent progress on the weight distributions of cyclic codes over finite fields, which had been determined by exponential sums. The cyclic codes with few weights which are very useful are discussed and their existence conditions are listed. Furthermore, we discuss the more general case of constacyclic codes and give some equivalences to characterize their weight distributions.

Cyclic peptides as potential therapeutic agents for skin disorders.

Science.gov (United States)

Namjoshi, Sarika; Benson, Heather A E

2010-01-01

There is an increasing understanding of the role of peptides in normal skin function and skin disease. With this knowledge, there is significant interest in the application of peptides as therapeutics in skin disease or as cosmeceuticals to enhance skin appearance. In particular, antimicrobial peptides and those involved in inflammatory processes provide options for the development of new therapeutic directions in chronic skin conditions such as psoriasis and dermatitis. To exploit their potential, it is essential that these peptides are delivered to their site of action in active form and in sufficient quantity to provide the desired effect. Many polymers permeate the skin poorly and are vulnerable to enzymatic degradation. Synthesis of cyclic peptide derivatives can substantially alter the physicochemical characteristics of the peptide with the potential to improve its skin permeation. In addition, cyclization can stabilize the peptide structure and thereby increase its stability. This review describes the role of cyclic peptides in the skin, examples of current cyclic peptide therapeutic products, and the potential for cyclic peptides as dermatological therapeutics and cosmeceuticals.

Cyclic AMP system in muscle tissue during prolonged hypokinesia

Science.gov (United States)

Antipenko, Y. A.; Bubeyev, Y. A.; Korovkin, B. F.; Mikhaleva, N. P.

1980-01-01

Components of the cyclic Adenosine-cyclic-35-monophosphate (AMP) system in the muscle tissue of white rats were studied during 70-75 days of hypokinesia, created by placing the animals in small booths which restricted their movements, and during the readaptation period. In the initial period, cyclic AMP levels and the activities of phosphodiesterase and adenylate cyclase in muscle tissue were increased. The values for these indices were roughly equal for controls and experimental animals during the adaptation period, but on the 70th day of the experiment cAMP levels dropped, phosphodiesterase activity increased, and the stimulative effect of epinephrine on the activity of adenylate cyclase decreased. The indices under study normalized during the readaptation period.

Response of monopiles under cyclic lateral loading in sand

DEFF Research Database (Denmark)

Nicolai, Giulio; Ibsen, Lars Bo

2015-01-01

Currently the main design guidelines propose to reduce the lateral resistance of offshore piles when accounting for cyclic loading. The present work provides results from laboratory tests in which such reduction has not occurred. The experimental investigation is based on testing a small......-scale monopile model in dense saturated sand. The experimental setup used to carry out the laboratory tests is able to apply thousands of load cycles and static loading to the monopile model. The purpose of the laboratory tests is to investigate the effects of cyclic loading on the lateral resistance...... of the monopile. It is shown that the soil-pile system becomes stiffer and more resistant after applying cyclic loading, depending on the number of cycles....

Facile and Green Synthesis of Saturated Cyclic Amines

Directory of Open Access Journals (Sweden)

Arruje Hameed

2017-10-01

Full Text Available Single-nitrogen containing saturated cyclic amines are an important part of both natural and synthetic bioactive compounds. A number of methodologies have been developed for the synthesis of aziridines, azetidines, pyrrolidines, piperidines, azepanes and azocanes. This review highlights some facile and green synthetic routes for the synthesis of unsubstituted, multisubstituted and highly functionalized saturated cyclic amines including one-pot, microwave assisted, metal-free, solvent-free and in aqueous media.

Deformation localization and cyclic strength in polycrystalline molybdenum

Energy Technology Data Exchange (ETDEWEB)

Sidorov, O.T.; Rakshin, A.F.; Fenyuk, M.I.

1983-06-01

Conditions of deformation localization and its interrelation with cyclic strength in polycrystalline molybdenum were investigated. A fatigue failure of polycrystalline molybdenum after rolling and in an embrittled state reached by recrystallization annealing under cyclic bending at room temperature takes place under nonuniform distribution of microplastic strain resulting in a temperature rise in separate sections of more than 314 K. More intensive structural changes take place in molybdenum after rolling than in recrystallized state.

Scale factor duality for conformal cyclic cosmologies

Energy Technology Data Exchange (ETDEWEB)

Silva, University Camara da; Lima, A.L. Alves; Sotkov, G.M. [Departamento de Física - CCE,Universidade Federal de Espirito Santo, 29075-900, Vitoria ES (Brazil)

2016-11-16

The scale factor duality is a symmetry of dilaton gravity which is known to lead to pre-big-bang cosmologies. A conformal time version of the scale factor duality (SFD) was recently implemented as a UV/IR symmetry between decelerated and accelerated phases of the post-big-bang evolution within Einstein gravity coupled to a scalar field. The problem investigated in the present paper concerns the employment of the conformal time SFD methods to the construction of pre-big-bang and cyclic extensions of these models. We demonstrate that each big-bang model gives rise to two qualitatively different pre-big-bang evolutions: a contraction/expansion SFD model and Penrose’s Conformal Cyclic Cosmology (CCC). A few examples of SFD symmetric cyclic universes involving certain gauged Kähler sigma models minimally coupled to Einstein gravity are studied. We also describe the specific SFD features of the thermodynamics and the conditions for validity of the generalized second law in the case of Gauss-Bonnet (GB) extension of these selected CCC models.

Scale factor duality for conformal cyclic cosmologies

International Nuclear Information System (INIS)

Silva, University Camara da; Lima, A.L. Alves; Sotkov, G.M.

2016-01-01

The scale factor duality is a symmetry of dilaton gravity which is known to lead to pre-big-bang cosmologies. A conformal time version of the scale factor duality (SFD) was recently implemented as a UV/IR symmetry between decelerated and accelerated phases of the post-big-bang evolution within Einstein gravity coupled to a scalar field. The problem investigated in the present paper concerns the employment of the conformal time SFD methods to the construction of pre-big-bang and cyclic extensions of these models. We demonstrate that each big-bang model gives rise to two qualitatively different pre-big-bang evolutions: a contraction/expansion SFD model and Penrose’s Conformal Cyclic Cosmology (CCC). A few examples of SFD symmetric cyclic universes involving certain gauged Kähler sigma models minimally coupled to Einstein gravity are studied. We also describe the specific SFD features of the thermodynamics and the conditions for validity of the generalized second law in the case of Gauss-Bonnet (GB) extension of these selected CCC models.

Classification and sedimentary characteristics of lacustrine hyperpycnal channels: Triassic outcrops in the south Ordos Basin, central China

Science.gov (United States)

Xian, Benzhong; Wang, Junhui; Gong, Chenglin; Yin, Yu; Chao, Chuzhi; Liu, Jianping; Zhang, Guodong; Yan, Qi

2018-06-01

Subaquatic channels are known as active conduits for the delivery of terrigenous sediments into related marine and lacustrine basins, as well as important targets for hydrocarbon exploration. Compared to submarine channels, lacustrine subaqueous channels created by hyperpycnal flows are understudied. Using well-exposed outcrops collected from three different locations in the southern Ordos Basin, central China, morphologies and architecture of a channelized hyperpycnal system were studied and classified. Six facies associations represent sedimentary processes from strong erosion by bedload dominated hyperpycnal flows, to transitional deposition jointly controlled by bedload and suspended-load dominated hyperpycnal flows, finally to deposition from suspended-load dominated hyperpycnal flows. On the basis of channel morphologies, infilling sediments and sedimentary processes, the documented channels can be classified into four main categories, which are erosional, bedload dominated, suspended-load dominated, and depositional channels. In very proximal and very distal locations, erosional channels and depositional channels serve as two end-members, while in middle areas, bedload-dominated channels and suspended-load dominated channels are transitional types. Erosional channels, as a response to strong erosion from bedload dominated hyperpycnal flows on upper slope, were mainly filled by mud interbedded with thin sand beds. As flow energy decreases, bedload dominated channels develop on middle slopes, which are characterized mainly by under- to balanced sediment infillings with cross-bedded sandstones and/or minor massive sandstones. Compared to bedload dominated channels, suspended-load dominated channels mainly develop in deeper water, and were filled mainly by massive or planar-laminated sandstones. Depositional channels, as a response to suspended-load dominated hyperpycnal flows in deep-water areas, are characterized by thin-medium bed classical turbidites with

Waiting-time approximations in multi-queue systems with cyclic service

NARCIS (Netherlands)

Boxma, O.J.; Meister, B.W.

1987-01-01

This study is devoted to mean waiting-time approximations in a single-server multi-queue model with cyclic service and zero switching times of the server between consecutive queues. Two different service disciplines are considered: exhaustive service and (ordinary cyclic) nonexhaustive service. For

Ceramic breeder pebble bed packing stability under cyclic loads

Energy Technology Data Exchange (ETDEWEB)

Zhang, Chunbo, E-mail: chunbozhang@fusion.ucla.edu [Fusion Science and Technology Center, University of California, Los Angeles, CA 90095-1597 (United States); Ying, Alice; Abdou, Mohamed A. [Fusion Science and Technology Center, University of California, Los Angeles, CA 90095-1597 (United States); Park, Yi-Hyun [National Fusion Research Institute, Daejeon (Korea, Republic of)

2016-11-01

Highlights: • The feasibility of obtaining packing stability for pebble beds is studied. • The responses of pebble bed to cyclic loads have been presented and analyzed in details. • Pebble bed packing saturation and its applications are discussed. • A suggestion is made regarding the improvement of pebbles filling technique. - Abstract: Considering the optimization of blanket performance, it is desired that the bed morphology and packing state during reactor operation are stable and predictable. Both experimental and numerical work are performed to explore the stability of pebble beds, in particular under pulsed loading conditions. Uniaxial compaction tests have been performed for both KIT’s Li{sub 4}SiO{sub 4} and NFRI’s Li{sub 2}TiO{sub 3} pebble beds at elevated temperatures (up to 750 °C) under cyclic loads (up to 6 MPa). The obtained data shows the stress-strain loop initially moves towards the larger strain and nearly saturates after a certain number of cyclic loading cycles. The characterized FEM CAP material models for a Li{sub 4}SiO{sub 4} pebble bed with an edge-on configuration are used to simulate the thermomechanical behavior of pebble bed under ITER pulsed operations. Simulation results have shown the cyclic variation of temperature/stress/strain/gap and also the same saturation trend with experiments under cyclic loads. Therefore, it is feasible for pebble bed to maintain its packing stability during operation when disregarding pebbles’ breakage and irradiation.

INFLUENCE OF INTERMITTENT CYCLIC LOADING ON REINFORCED CONCRETE RESISTANCE MODEL

Directory of Open Access Journals (Sweden)

Vasyl Karpiuk

2017-01-01

Full Text Available This article describes the study of reinforced concrete span bending structures under conditions of high-level cyclic loading. Previous studies on the development of physical models of bending reinforced concrete element fatigue resistance, cyclic effect of lateral forces, and methods of calculation, are important and appropriate owing to certain features and the essential specificity of the mentioned loading type. These primarily include the nonlinearity of deformation, damage accumulation in the form of fatigue micro- and macro-cracks, and exhausting destruction of construction materials. In this paper, key expressions determining the endurance limits of concrete, longitudinal reinforcement, and anchoring longitudinal reinforcement, which contribute to endurance throughout the entire construction, are considered. Establishing a link between stresses in the elements and deformations in the element under conditions of cyclic loading action is of equal importance because of the presence of cyclic stress-induced creep deformation.

STRATEGIES FOR SUPERIOR PERFORMANCE IN RECESSIONS: PRO OR COUNTER-CYCLICAL?

Directory of Open Access Journals (Sweden)

Claudio Ramos Conti

2015-04-01

Full Text Available Recessions are recurring events in which most firms suffer severe impacts while others are less affected or may even prosper. Strategic management has made little progress in understanding such performance differences. In a scenario of decreased demand, intensified competition, and higher uncertainty, most firms try to survive by pro-cyclically cutting costs and investments. But firms could take advantage of undervalued resources in the market to counter-cyclically invest in new business opportunities to overtake competitors. We survey Brazilian firms in various industries about the 2008-2009 recession and analyze data using PLS-SEM. We find that while most firms pro-cyclically reduce costs and investments in recessions, a counter-cyclical strategy of investing in opportunities created by changes in the market enables superior performance. Most successful are firms with a propensity to recognize opportunities, an entrepreneurial orientation to invest, and the flexibility to efficiently implement investments.

Record of palaeoenvironmental changes in a Lower Permian organic-rich lacustrine succession: Integrated sedimentological and geochemical study of the Rudník member, Krkonoše Piedmont Basin, Czech Republic

Czech Academy of Sciences Publication Activity Database

Martínek, K.; Blecha, M.; Daněk, V.; Franců, J.; Hladíková, J.; Johnová, R.; Uličný, David

2006-01-01

Roč. 230, 1/2 (2006), s. 85-128 ISSN 0031-0182 R&D Projects: GA ČR GA205/94/0692 Institutional research plan: CEZ:AV0Z30120515 Keywords : Lower Permian * Bohemian Massif * lacustrine facies Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.822, year: 2006

Results on Cyclic Signal Processing Systems

National Research Council Canada - National Science Library

Vaidyanathan, P

1998-01-01

.... A number of related problems such as the paraunitary interpolation problem and the cyclic paraunitary factorizability problem can be understood in a unified way by using the realization matrix...

Activation of the adenylyl cyclase/cyclic AMP/protein kinase A pathway in endothelial cells exposed to cyclic strain

Science.gov (United States)

Cohen, C. R.; Mills, I.; Du, W.; Kamal, K.; Sumpio, B. E.

1997-01-01

The aim of this study was to assess the involvement of the adenylyl cyclase/cyclic AMP/protein kinase A pathway (AC) in endothelial cells (EC) exposed to different levels of mechanical strain. Bovine aortic EC were seeded to confluence on flexible membrane-bottom wells. The membranes were deformed with either 150 mm Hg (average 10% strain) or 37.5 mm Hg (average 6% strain) vacuum at 60 cycles per minute (0.5 s strain; 0.5 s relaxation) for 0-60 min. The results demonstrate that at 10% average strain (but not 6% average strain) there was a 1.5- to 2.2-fold increase in AC, cAMP, and PKA activity by 15 min when compared to unstretched controls. Further studies revealed an increase in cAMP response element binding protein in EC subjected to the 10% average strain (but not 6% average strain). These data support the hypothesis that cyclic strain activates the AC/cAMP/PKA signal transduction pathway in EC which may occur by exceeding a strain threshold and suggest that cyclic strain may stimulate the expression of genes containing cAMP-responsive promoter elements.

Introduction of a cyclic-fermentation method

Energy Technology Data Exchange (ETDEWEB)

Makarova, C P

1958-01-01

Equipment is described, consisting of 8 kettles, which permits a cyclic fermentation process and continuous ethanol production; 100% yields of ethanol are obtained, based on the starch content in grain.

Testing and modeling of cyclically loaded rock anchors

Directory of Open Access Journals (Sweden)

Joar Tistel

2017-12-01

Full Text Available The Norwegian Public Roads Administration (NPRA is planning for an upgrade of the E39 highway route at the westcoast of Norway. Fixed links shall replace ferries at seven fjord crossings. Wide spans and large depths at the crossings combined with challenging subsea topography and environmental loads call for an extension of existing practice. A variety of bridge concepts are evaluated in the feasibility study. The structures will experience significant loads from deadweight, traffic and environment. Anchoring of these forces is thus one of the challenges met in the project. Large-size subsea rock anchors are considered a viable alternative. These can be used for anchoring of floating structures but also with the purpose of increasing capacity of fixed structures. This paper presents first a thorough study of factors affecting rock anchor bond capacity. Laboratory testing of rock anchors subjected to cyclic loading is thereafter presented. Finally, the paper presents a model predicting the capacity of a rock anchor segment, in terms of a ribbed bar, subjected to a cyclic load history. The research assumes a failure mode occurring in the interface between the rock anchor and the surrounding grout. The constitutive behavior of the bonding interface is investigated for anchors subjected to cyclic one-way tensile loads. The model utilizes the static bond capacity curve as a basis, defining the ultimate bond τbu and the slip s1 at τbu. A limited number of input parameters are required to apply the model. The model defines the bond-slip behavior with the belonging rock anchor capacity depending on the cyclic load level (τmax cy/τbu, the cyclic load ratio (R = τmin cy/τmax cy, and the number of load cycles (N. The constitutive model is intended to model short anchor lengths representing an incremental length of a complete rock anchor.

Controls on Cyclic Formation of Quaternary Early Diagenetic Dolomite

Science.gov (United States)

McCormack, J.; Bontognali, T. R. R.; Immenhauser, A.; Kwiecien, O.

2018-04-01

The origin of sedimentary dolomite and the factors that control its formation within the geological record remain speculative. In most models, dolomite formation is linked to evaporative conditions, high water temperature, increasing Mg/Ca ratio, increasing alkalinity, and high amounts of biomass. Here we challenge these archetypal views, by documenting a case example of Quaternary dolomite which formed in Lake Van at constantly low temperature (stress, resulting from reventilation of the water-sediment interface. Independently from the validity of this hypothesis, our results call for a reevaluation of the paleoenvironmental conditions often invoked for early diagenetic dolomite-rich intervals within sedimentary sequences and for caution when interpreting time series of subrecent lacustrine carbonates.

Cyclic settlement behavior of strip footings resting on reinforced layered sand slope

Directory of Open Access Journals (Sweden)

Mostafa A. El Sawwaf

2012-10-01

Full Text Available The paper presents a study of the behavior of model strip footings supported on a loose sandy slope and subjected to both monotonic and cyclic loads. The effects of the partial replacement of a compacted sand layer and the inclusion of geosynthetic reinforcement were investigated. Different combinations of the initial monotonic loads and the amplitude of cyclic loads were chosen to simulate structures in which loads change cyclically such as machine foundations. The affecting factors including the location of footing relative to the slope crest, the frequency of the cyclic load and the number of load cycles were studied. The cumulative cyclic settlement of the model footing supported on a loose sandy slope, un-reinforced and reinforced replaced sand deposits overlying the loose slope were obtained and compared. Test results indicate that the inclusion of soil reinforcement in the replaced sand not only significantly increases the stability of the sandy slope itself but also decreases much both the monotonic and cumulative cyclic settlements leading to an economic design of the footings. However, the efficiency of the sand–geogrid systems depends on the properties of the cyclic load and the location of the footing relative to the slope crest. Based on the test results, the variation of cumulative settlements with different parameters is presented and discussed.

Levels of cyclic-2,3-diphosphoglycerate in Methanobacterium thermoautotrophicum during phosphate limitation.

Science.gov (United States)

Seely, R J; Fahrney, D E

1984-10-01

Batch-grown Methanobacterium thermoautotrophicum cells grew nonexponentially in the absence of exogenous Pi until intracellular cyclic-2,3-diphosphoglycerate (cyclic DPG) had fallen below 2 mumol/g (dry weight), the limit of detection. Growth resumed immediately upon transfer to medium containing Pi Cyclic DPG levels were also below detection in Pi-limited chemostat cultures operating at a dilution rate of 0.173 h-1 (4-h doubling time), with reservoir Pi concentrations below 200 microM. At this dilution rate, the Pi concentration in the culture was 4 microM. An H2-limited steady state was achieved with 400 microM Pi in the inflowing medium (67 microM in the culture). The cyclic DPG content of these cells was 72 to 74 mumol/g, about one-third the amount in batch-grown cells. The specific growth rate accelerated immediately to 0.36 h-1 (1.9-h doubling time) under washout conditions at high dilution rate. The cellular content of cyclic DPG declined over a 2-h period, and then increased rapidly as the Pi level in the medium approached 200 microM. Expansion of the cyclic DPG pool coincided with a marked increase in Pi assimilation. These results indicated that M. thermoautotrophicum accumulated cyclic DPG only when Pi and H2 were readily available.

Levels of cyclic-2,3-diphosphoglycerate in Methanobacterium thermoautotrophicum during phosphate limitation.

Science.gov (United States)

Seely, R J; Fahrney, D E

1984-01-01

Batch-grown Methanobacterium thermoautotrophicum cells grew nonexponentially in the absence of exogenous Pi until intracellular cyclic-2,3-diphosphoglycerate (cyclic DPG) had fallen below 2 mumol/g (dry weight), the limit of detection. Growth resumed immediately upon transfer to medium containing Pi Cyclic DPG levels were also below detection in Pi-limited chemostat cultures operating at a dilution rate of 0.173 h-1 (4-h doubling time), with reservoir Pi concentrations below 200 microM. At this dilution rate, the Pi concentration in the culture was 4 microM. An H2-limited steady state was achieved with 400 microM Pi in the inflowing medium (67 microM in the culture). The cyclic DPG content of these cells was 72 to 74 mumol/g, about one-third the amount in batch-grown cells. The specific growth rate accelerated immediately to 0.36 h-1 (1.9-h doubling time) under washout conditions at high dilution rate. The cellular content of cyclic DPG declined over a 2-h period, and then increased rapidly as the Pi level in the medium approached 200 microM. Expansion of the cyclic DPG pool coincided with a marked increase in Pi assimilation. These results indicated that M. thermoautotrophicum accumulated cyclic DPG only when Pi and H2 were readily available. PMID:6480564

A uniaxial cyclic elastoplastic constitutive law with a discrete memory variable

International Nuclear Information System (INIS)

Taheri, S.

1991-01-01

At present, the study on cyclic elastoplastic constitutive laws is focused on nonproportional loading, but for uniaxial loading, some problems still exist. For example, the possibility for a law to describe simultaneously the ratcheting in nonsymmetrical load-controlled test, elastic and plastic shakedown in symmetrical and nonsymmetrical ones. Here a law is presented, which in addition to previous phenomena, describes the cyclic hardening in a pushpull test, the cyclic softening after overloading and also the dependence of cyclic strain-stress curves on the history of loading. These are the usual properties of 316 stainless steel at room temperature. This law uses an internal discrete memory variable: the plastic strain at the last unloading. On the other hand, the choice of all macroscopic variables is justified by a microscopic analysis. This law has been also extended to a three-dimensional case. Regarding the microstructure under cyclic loading, plastic shakedown and ratcheting are discussed. The definition of macroscopic variables taking account of microstructure and uniaxial constitutive law are described. (K.I.)

Earl Sutherland (1915-1974) [corrected] and the discovery of cyclic AMP.

Science.gov (United States)

Blumenthal, Stanley A

2012-01-01

In 1945, Earl Sutherland (1915-1974) [corrected] and associates began studies of the mechanism of hormone-induced glycogen breakdown in the liver. In 1956, their efforts culminated in the identification of cyclic AMP, an ancient molecule generated in many cell types in response to hormonal and other extracellular signals. Cyclic AMP, the original "second messenger," transmits such signals through pathways that regulate a diversity of cellular functions and capabilities: metabolic processes such as lipolysis and glycogenolysis; hormone secretion; the permeability of ion channels; gene expression; cell proliferation and survival. Indeed, it can be argued that the discovery of cyclic AMP initiated the study of intracellular signaling pathways, a major focus of contemporary biomedical inquiry. This review presents relevant details of Sutherland's career; summarizes key contributions of his mentors, Carl and Gerti Cori, to the knowledge of glycogen metabolism (contributions that were the foundation for his own research); describes the experiments that led to his identification, isolation, and characterization of cyclic AMP; assesses the significance of his work; and considers some aspects of the impact of cyclic nucleotide research on clinical medicine.

14 C dating and isotopic composition of lacustrine sediment in the Vale do Ribeira, south-western Sao Paulo State

International Nuclear Information System (INIS)

Saia, Soraya E.M.G.; Pessenda, Luiz C.R.; Gouveia, Susy E.M.; Vidotto, Elaine; Ledru, Marie-Pierre; Karmann, Ivo; Amaral, Paula G.; Bendassoli, Jose A.

2005-01-01

This work is part of a multi and interdisciplinary study involving paleoenvironmental records based on systematic and joint actions of pollen, isotopic composition ( 12 C, 13 C and 14 N, 15 N) and 14 C dating of lacustrine sediment. Samplings have been made in the Lagoa Grande located at Parque Estadual de Turismo do Alto Ribeira - PETAR, in the Vale do Ribeira, south-western Sao Paulo state. This integration must improve significantly the studies of vegetation and climate changes that occurred during the Late Pleistocene in the southeastern region of Brazil. The δ 13 C results of lacustrine sediment presented values from -23 to -30 per mille with isotopic tendencies of enrichment-depletion in the whole profile. The highest values of total organic carbon (TOC) and C/N associated with depleted δ 13 C values, were linked to organic matter from C 3 land plant and interpreted as the presence of denser arboreal vegetation around the lake. The smallest values of TOC and C/N associated with enriched δ 13 C values were linked to phytoplanktonic influence and/or the presence of less dense arboreal vegetation around the lake. These fluctuations reflect changes in quality and quantity of sedimentary organic matter linked to vegetation changes and the production of organic matter within the sedimentation basin connected with lake level variations. The combination of C/N and δ 13 C data on a cross-plot diagram shows a general distribution of points lying close to the planktonic (algal) organic matter. However, the scattering of certain points indicates a slight contribution from C 3 land plants. The variations in arboreal pollen (%AP) along the core are characterized by AP values between 40 and 80%. The 14C dating indicated Modern age at the shallow horizons to 1,030 years BP for the deeper horizon. (author)

The Cyclic AMP-Vfr Signaling Pathway in Pseudomonas aeruginosa Is Inhibited by Cyclic Di-GMP

DEFF Research Database (Denmark)

Almblad, Henrik; Harrison, Joe J; Rybtke, Morten

2015-01-01

infection give rise to rugose small colony variants (RSCVs), which are hyper-biofilm-forming mutants that commonly possess mutations that increase production of the biofilm-promoting secondary messenger cyclic di-GMP (c-di-GMP). We show that RSCVs display a decreased production of acute virulence factors...... as a direct result of elevated c-di-GMP content. Overproduction of c-di-GMP causes a decrease in the transcription of virulence factor genes that are regulated by the global virulence regulator Vfr. The low level of Vfr-dependent transcription is caused by a low level of its coactivator, cyclic AMP (c......AMP), which is decreased in response to a high level of c-di-GMP. Mutations that cause reversion of the RSCV phenotype concomitantly reactivate Vfr-cAMP signaling. Attempts to uncover the mechanism underlying the observed c-di-GMP-mediated lowering of cAMP content provided evidence that it is not caused...

Synthesis of Cyclic Antifreeze Glycopeptide and Glycopeptoids and Their Ice Recrystallization Inhibition Activity

International Nuclear Information System (INIS)

Ahn, Mija; Murugan, Ravichandran N.; Bang, Jeong Kyu; Kim, Hak Jun; Shin, Song Yub; Kim, Eunjung; Lee, Jun Hyuck

2012-01-01

Until now, few groups reported the antifreeze activity of cyclic glycopeptides; however, the tedious synthetic procedure is not amenable to study the intensive structure activity relationship. A series of N-linked cyclic glycopeptoids and glycopeptide have been prepared to evaluate antifreeze activity as a function of peptide backbone cyclization and methyl stereochemical effect on the rigid Thr position. This study has combined the cyclization protocol with solid phase peptide synthesis and obtained significant quantities of homogeneous cyclic glycopeptide and glycopeptoids. Analysis of antifreeze activity revealed that our cyclic peptide demonstrated RI activity while cyclic glycopeptoids showed no RI activity. These results suggest that the subtle changes in conformation and Thr orientation dramatically influence RI activity of N-linked glycopeptoids

Cyclic complex loading of 316 stainless steel: Experiments and calculations

International Nuclear Information System (INIS)

Jacquelin, B.; Hourlier, F.; Dang Van, K.; Stolz, C.

1981-01-01

To test the ability of cyclic constitutive law established by mean of uniaxial test a benchmark is proposed. The calculated results using the model of Chaboche-Cordier-Dang Van are compared with experimental data obtained on cylindrical specimens undergoing simultaneously constant torque and cyclic tension. (orig.)

The effect of ultraviolet light on the cyclic nucleotide system of human fibroblasts

International Nuclear Information System (INIS)

Fertel, R.H.; Tejwani, G.A.; Albrightson, C.R.; Hart, R.W.

1981-01-01

The concentrations of cyclic AMP and cyclic GMP in in human skin fibroblasts in culture were determined after exposing the cells to varying fluences of UV (254 nm) light. The cyclic nucleotide concentrations of cells irradiated in the log phase of growth were unchanged relative to controls. In contrast, there was a rise in the concentration of cyclic AMP in cells irradiated after they reached confluency. The increase in concentration was observed as early as 30 min after irradiation, reached a maximum of about 200% of control at 4 to 6 h after exposure, and returned to control values by 24 h after irradiation. The effect was proportional to a UV fluence from 5 to 20 J/m 2 , and was blocked by the addition of the UV absorbing agent para-aminobenzoic acid. In contrast, the results indicated that UV light had no effect on the concentration of cyclic GMP in human fibroblast cell cultures. Because of the importance of cyclic nucleotides in the regulation of cellular function, it is reasonable to hypothesize that changes in cyclic AMP induced by UV light may effect the extranuclear functions of irradiated cells. (author)

Retinal Cyclic Nucleotide-Gated Channels: From Pathophysiology to Therapy

Directory of Open Access Journals (Sweden)

Stylianos Michalakis

2018-03-01

Full Text Available The first step in vision is the absorption of photons by the photopigments in cone and rod photoreceptors. After initial amplification within the phototransduction cascade the signal is translated into an electrical signal by the action of cyclic nucleotide-gated (CNG channels. CNG channels are ligand-gated ion channels that are activated by the binding of cyclic guanosine monophosphate (cGMP or cyclic adenosine monophosphate (cAMP. Retinal CNG channels transduce changes in intracellular concentrations of cGMP into changes of the membrane potential and the Ca2+ concentration. Structurally, the CNG channels belong to the superfamily of pore-loop cation channels and share a common gross structure with hyperpolarization-activated cyclic nucleotide-gated (HCN channels and voltage-gated potassium channels (KCN. In this review, we provide an overview on the molecular properties of CNG channels and describe their physiological role in the phototransduction pathways. We also discuss insights into the pathophysiological role of CNG channel proteins that have emerged from the analysis of CNG channel-deficient animal models and human CNG channelopathies. Finally, we summarize recent gene therapy activities and provide an outlook for future clinical application.

Cyclic Nucleotide Monophosphates and Their Cyclases in Plant Signaling

KAUST Repository

Gehring, Christoph A; Turek, Ilona S.

2017-01-01

The cyclic nucleotide monophosphates (cNMPs), and notably 3′,5′-cyclic guanosine monophosphate (cGMP) and 3′,5′-cyclic adenosine monophosphate (cAMP) are now accepted as key signaling molecules in many processes in plants including growth and differentiation, photosynthesis, and biotic and abiotic defense. At the single molecule level, we are now beginning to understand how cNMPs modify specific target molecules such as cyclic nucleotide-gated channels, while at the systems level, a recent study of the Arabidopsis cNMP interactome has identified novel target molecules with specific cNMP-binding domains. A major advance came with the discovery and characterization of a steadily increasing number of guanylate cyclases (GCs) and adenylate cyclases (ACs). Several of the GCs are receptor kinases and include the brassinosteroid receptor, the phytosulfokine receptor, the Pep receptor, the plant natriuretic peptide receptor as well as a nitric oxide sensor. We foresee that in the near future many more molecular mechanisms and biological roles of GCs and ACs and their catalytic products will be discovered and further establish cNMPs as a key component of plant responses to the environment.

Cyclic Nucleotide Monophosphates and Their Cyclases in Plant Signaling

KAUST Repository

Gehring, Christoph A.

2017-10-04

The cyclic nucleotide monophosphates (cNMPs), and notably 3′,5′-cyclic guanosine monophosphate (cGMP) and 3′,5′-cyclic adenosine monophosphate (cAMP) are now accepted as key signaling molecules in many processes in plants including growth and differentiation, photosynthesis, and biotic and abiotic defense. At the single molecule level, we are now beginning to understand how cNMPs modify specific target molecules such as cyclic nucleotide-gated channels, while at the systems level, a recent study of the Arabidopsis cNMP interactome has identified novel target molecules with specific cNMP-binding domains. A major advance came with the discovery and characterization of a steadily increasing number of guanylate cyclases (GCs) and adenylate cyclases (ACs). Several of the GCs are receptor kinases and include the brassinosteroid receptor, the phytosulfokine receptor, the Pep receptor, the plant natriuretic peptide receptor as well as a nitric oxide sensor. We foresee that in the near future many more molecular mechanisms and biological roles of GCs and ACs and their catalytic products will be discovered and further establish cNMPs as a key component of plant responses to the environment.

Holocene environmental changes in northern Lebanon as inferred from a multiproxy study on lacustrine-palustrine sediment

Science.gov (United States)

Vidal, Laurence; Jenna, Hage-Hassen; Demory, François; Develle, Anne-Lise; van Campo, Elise; Elias, Ata

2016-04-01

The reconstruction of the Levantine post-glacial environmental evolution is essential to understand the interactions between variability of regional water cycle, dynamics of the global climate, and cultural evolution. We present a paleolacustrine record from the karstic Yammouneh basin (34.06N-34.09N; 36.0E-36.03E, 1360 m a.s.l.), located on the eastern flank of Mount Lebanon (northern Levant). Holocene sediments (retrieved from gully and a trenbch) (1.5 to 3.6 m thick) consist of pale lacustrine chalk interrupted by an ash layer and remarkable centimetric beds of ocher to dark brown silty clays used, in addition to 14C ages, as stratigraphical markers. Lacustrine biogenic remains are diversified and abundant (ostracods, gastropods, charophytes, chlorophyceae, plant debris…) all reflecting a freswater, generally shallow waterbody. We analysed the sediment mineralogy and geochemistry, TOM contents, magnetic properties, pollen and calcite oxygen isotope composition derived from ostracod shells. These sequences are compared to former data from 2 trenches and 1 core collected in different points of the basin (Daeron et al., 2007; Develle et al., 2009, 2010). A total of 42 AMS 14C dating (partly carbonized wood) provide a solid chronology from the YD to present. Results reveal the following main features : 1- intervals dominated by authigenic calcite suggest that the major water supply was the karstic springs, which still deliver Ca-rich water and low surface runoff; 2- the lake oxygen isotope composition has been impacted by the source isotope composition throughout the Holocene and by increased inland rainfall during the early Holocene; 3- a decideous oak forest, implying much more soil water availability than today, was developed around the lake from ca. 11.5 to 9.5 kyr (the very bad pollen preservation after 8.3 kyr reflects oxidation or frequent oscillations of the water level); 4- four paleosols evidenced from lithofacies and magnetic properties are identified

The participation of elevated levels of cyclic GMP in the recovery from radiation-induced mitotic delay

International Nuclear Information System (INIS)

Daniel, J.W.; Oleinick, N.L.

1984-01-01

The levels of cyclic AMP and cyclic GMP have been measured in Physarum plasmodia before and after treatment with gamma-radiation, 2 mM caffeine, or combinations of the two agents compared to the length of the radiation-induced mitotic delay. Caffeine alone produces a rapid transient elevation of cyclic AMP and a slower delayed elevation of cyclic GMP. Irradiation elicits an immediate transient increase in cyclic AMP and a later cyclic GMP increase which accompanies or precedes the delayed mitosis. A composite pattern is produced by combinations of radiation and caffeine, a distinctive feature of which is an elevated level of cyclic GMP near the time of the radiation-delayed and caffeine-promoted mitosis. With pretreatment by caffeine, the least radiation-induced mitotic delay occurs when plasmodia are irradiated during the caffeine-elicited increase in cyclic GMP. The plasmodium becomes refractory to the reduction of mitotic delay by caffeine at approximately the time it becomes refractory to the further elevation of cyclic GMP by caffeine. The data support a role for cyclic AMP in the onset of and for cyclic GMP in the recovery from mitotic delay induced by ionizing radiation. (author)

Numerical modeling of centrifuge cyclic lateral pile load experiments

Science.gov (United States)

Gerolymos, Nikos; Escoffier, Sandra; Gazetas, George; Garnier, Jacques

2009-03-01

To gain insight into the inelastic behavior of piles, the response of a vertical pile embedded in dry sand and subjected to cyclic lateral loading was studied experimentally in centrifuge tests conducted in Laboratoire Central des Ponts et Chaussées. Three types of cyclic loading were applied, two asymmetric and one symmetric with respect to the unloaded pile. An approximately square-root variation of soil stiffness with depth was obtained from indirect in-flight density measurements, laboratory tests on reconstituted samples, and well-established empirical correlations. The tests were simulated using a cyclic nonlinear Winkler spring model, which describes the full range of inelastic phenomena, including separation and re-attachment of the pile from and to the soil. The model consists of three mathematical expressions capable of reproducing a wide variety of monotonic and cyclic experimental p-y curves. The physical meaning of key model parameters is graphically explained and related to soil behavior. Comparisons with the centrifuge test results demonstrate the general validity of the model and its ability to capture several features of pile-soil interaction, including: soil plastification at an early stage of loading, “pinching” behavior due to the formation of a relaxation zone around the upper part of the pile, and stiffness and strength changes due to cyclic loading. A comparison of the p-y curves derived from the test results and the proposed model, as well as those from the classical curves of Reese et al. (1974) for sand, is also presented.

Cyclic Vomiting Syndrome in Children

Directory of Open Access Journals (Sweden)

T.V. Sorokman

2016-08-01

Full Text Available Introduction. Cyclic vomiting syndrome (CVS — is a fairly common disease of unknown etiology that affects children of all age groups and sometimes adult population and refers to the functional disorders of the gastrointestinal tract. Objective: to evaluate the effectiveness of the usage of Rehydron Optim for oral rehydration therapy in children. Materials and methods. The treatment of 40 children aged 3 to 11 years with CVS (15 persons and primary acetonemic syndrome (25 persons in the period of acetonemic crisis, including 15 boys and 25 girls, was analyzed. All children were observed in the outpatient department of the Regional children’s hospital of Chernivtsi. Diagnosis was established based on anamnesis, clinical and laboratory data. Patients underwent required clinico-biological tests and instrumental examinations. The dynamics of the following syndromes was investigated: pain, vomiting, dehydration and intoxication. Rehydration therapy in all cases was oral with the usage of Rehydron Optim. Results of the study and their discussion. A cyclical vomiting was observed in children with primary acetonemic syndrome with satisfactory condition in attack-free period. Migraine-like headaches prevailed in 36 patients (80 %, and the age of these patients was older than 7 years. Same children had episodes of paroxysmal autonomic failure. Almost all surveyed children had in their family history the risk factors for CVS development. All children had positive dynamics of the main basic clinical manifestations on the background of oral rehydration therapy using Rehydron Optim. Within the 1st day of oral rehydration therapy with Rehydron Optim in children, we have noted a significant decrease in the incidence of lethargy, vomiting, spastic abdominal pain, smell of acetone in the exhaled air (p < 0.05. In children with the I degree of dehydration, clinical signs of dehydration were not seen before the treatment, and children with the II degree had an

Windows(Registered Trademark)-Based Software Models Cyclic Oxidation Behavior

Science.gov (United States)

Smialek, J. L.; Auping, J. V.

2004-01-01

Oxidation of high-temperature aerospace materials is a universal issue for combustion-path components in turbine or rocket engines. In addition to the question of the consumption of material due to growth of protective scale at use temperatures, there is also the question of cyclic effects and spallation of scale on cooldown. The spallation results in the removal of part of the protective oxide in a discontinuous step and thereby opens the way for more rapid oxidation upon reheating. In experiments, cyclic oxidation behavior is most commonly characterized by measuring changes in weight during extended time intervals that include hundreds or thousands of heating and cooling cycles. Weight gains occurring during isothermal scale-growth processes have been well characterized as being parabolic or nearly parabolic functions of time because diffusion controls reaction rates. In contrast, the net weight change in cyclic oxidation is the sum of the effects of the growth and spallation of scale. Typically, the net weight gain in cyclic oxidation is determined only empirically (that is, by measurement), with no unique or straightforward mathematical connection to either the rate of growth or the amount of metal consumed. Thus, there is a need for mathematical modeling to infer spallation mechanisms. COSP is a computer program that models the growth and spallation processes of cyclic oxidation on the basis of a few elementary assumptions that were discussed in COSP: A Computer Model of Cyclic Oxidation, Oxidation of Metals, vol. 36, numbers 1 and 2, 1991, pages 81-112. Inputs to the model include the selection of an oxidation-growth law and a spalling geometry, plus oxide-phase, growth-rate, cycle-duration, and spall-constant parameters. (The spalling fraction is often shown to be a constant factor times the existing amount of scale.) The output of COSP includes the net change in weight, the amounts of retained and spalled oxide, the total amounts of oxygen and metal

Cyclic dominance in evolutionary games: a review

Science.gov (United States)

Szolnoki, Attila; Mobilia, Mauro; Jiang, Luo-Luo; Szczesny, Bartosz; Rucklidge, Alastair M.; Perc, Matjaž

2014-01-01

Rock is wrapped by paper, paper is cut by scissors and scissors are crushed by rock. This simple game is popular among children and adults to decide on trivial disputes that have no obvious winner, but cyclic dominance is also at the heart of predator–prey interactions, the mating strategy of side-blotched lizards, the overgrowth of marine sessile organisms and competition in microbial populations. Cyclical interactions also emerge spontaneously in evolutionary games entailing volunteering, reward, punishment, and in fact are common when the competing strategies are three or more, regardless of the particularities of the game. Here, we review recent advances on the rock–paper–scissors (RPS) and related evolutionary games, focusing, in particular, on pattern formation, the impact of mobility and the spontaneous emergence of cyclic dominance. We also review mean-field and zero-dimensional RPS models and the application of the complex Ginzburg–Landau equation, and we highlight the importance and usefulness of statistical physics for the successful study of large-scale ecological systems. Directions for future research, related, for example, to dynamical effects of coevolutionary rules and invasion reversals owing to multi-point interactions, are also outlined. PMID:25232048

Cyclic plastic hinges with degradation effects for frame structures

DEFF Research Database (Denmark)

Tidemann, Lasse; Krenk, Steen

2017-01-01

A model of cyclic plastic hinges in frame structures including degradation effects for stiffness and strength is developed. The model is formulated via potentials in terms of section forces. It consists of a yield surface, described in a generic format permitting representation of general convex...... shapes including corners, and a set of evolution equations based on an internal energy potential and a plastic flow potential. The form of these potentials is specified by five parameters for each generalized stress-strain component describing yield level, ultimate stress capacity, elastic...... and stiffness parameters. The cyclic plastic hinges are introduced into a six-component equilibrium-based beam element, using additive element and hinge flexibilities. When converted to stiffness format the plastic hinges are incorporated into the element stiffness matrix. The cyclic plastic hinge model...

Generalized Toeplitz operators and cyclic vectors

International Nuclear Information System (INIS)

Gassier, G.; Mahzouli, H.; Zerouali, E.H.

2003-04-01

We give in this paper some asymptotic Von Neumann inequalities for power bounded operators in the class C ρ intersection C 1 . and some spacial von Neumann inequalities associated with non zero elements of the point spectrum, when it is non void, of generalized Toeplitz operators. Introducing perturbed kernel, we consider classes C R which extend the classical classes C ρ . We give results about absolute continuity with respect to the Haar measure for operators in class C R intersection C 1 . This allows us to give new results on cyclic vectors for such operators and provides invariant subspaces for their powers. Relationships between cyclic vectors for T and T* involving generalized Toeplitz operators are given and the commutativity of {T}', the commutant of T is discussed. (author)

Cyclic Nucleotide Signalling in Kidney Fibrosis

Directory of Open Access Journals (Sweden)

Elisabeth Schinner

2015-01-01

Full Text Available Kidney fibrosis is an important factor for the progression of kidney diseases, e.g., diabetes mellitus induced kidney failure, glomerulosclerosis and nephritis resulting in chronic kidney disease or end-stage renal disease. Cyclic adenosine monophosphate (cAMP and cyclic guanosine monophosphate (cGMP were implicated to suppress several of the above mentioned renal diseases. In this review article, identified effects and mechanisms of cGMP and cAMP regarding renal fibrosis are summarized. These mechanisms include several signalling pathways of nitric oxide/ANP/guanylyl cyclases/cGMP-dependent protein kinase and cAMP/Epac/adenylyl cyclases/cAMP-dependent protein kinase. Furthermore, diverse possible drugs activating these pathways are discussed. From these diverse mechanisms it is expected that new pharmacological treatments will evolve for the therapy or even prevention of kidney failure.

Strain gradient effects on cyclic plasticity

DEFF Research Database (Denmark)

Niordson, Christian Frithiof; Legarth, Brian Nyvang

2010-01-01

Size effects on the cyclic shear response are studied numerically using a recent higher order strain gradient visco-plasticity theory accounting for both dissipative and energetic gradient hardening. Numerical investigations of the response under cyclic pure shear and shear of a finite slab between...... rigid platens have been carried out, using the finite element method. It is shown for elastic–perfectly plastic solids how dissipative gradient effects lead to increased yield strength, whereas energetic gradient contributions lead to increased hardening as well as a Bauschinger effect. For linearly...... hardening materials it is quantified how dissipative and energetic gradient effects promote hardening above that of conventional predictions. Usually, increased hardening is attributed to energetic gradient effects, but here it is found that also dissipative gradient effects lead to additional hardening...

A compact cyclic plasticity model with parameter evolution

DEFF Research Database (Denmark)

Krenk, Steen; Tidemann, L.

2017-01-01

The paper presents a compact model for cyclic plasticity based on energy in terms of external and internal variables, and plastic yielding described by kinematic hardening and a flow potential with an additive term controlling the nonlinear cyclic hardening. The model is basically described by five...... parameters: external and internal stiffness, a yield stress and a limiting ultimate stress, and finally a parameter controlling the gradual development of plastic deformation. Calibration against numerous experimental results indicates that typically larger plastic strains develop than predicted...

Multiaxial elastoplastic cyclic loading of austenitic 316L steel

Czech Academy of Sciences Publication Activity Database

Mazánová, Veronika; Polák, Jaroslav; Škorík, Viktor; Kruml, Tomáš

2017-01-01

Roč. 11, č. 40 (2017), s. 162-169 ISSN 1971-8993 R&D Projects: GA ČR(CZ) GA13-23652S; GA MŠk LM2015069; GA MŠk(CZ) LQ1601; GA ČR GA15-08826S Institutional support: RVO:68081723 Keywords : 316L steel * Crack initiation * Cyclic stress-strain curve * Multiaxial cyclic loading Subject RIV: JL - Materials Fatigue, Friction Mechanics OBOR OECD: Audio engineering, reliability analysis

On cyclic yield strength in definition of limits for characterisation of fatigue and creep behaviour

Science.gov (United States)

Gorash, Yevgen; MacKenzie, Donald

2017-06-01

This study proposes cyclic yield strength as a potential characteristic of safe design for structures operating under fatigue and creep conditions. Cyclic yield strength is defined on a cyclic stress-strain curve, while monotonic yield strength is defined on a monotonic curve. Both values of strengths are identified using a two-step procedure of the experimental stress-strain curves fitting with application of Ramberg-Osgood and Chaboche material models. A typical S-N curve in stress-life approach for fatigue analysis has a distinctive minimum stress lower bound, the fatigue endurance limit. Comparison of cyclic strength and fatigue limit reveals that they are approximately equal. Thus, safe fatigue design is guaranteed in the purely elastic domain defined by the cyclic yielding. A typical long-term strength curve in time-to-failure approach for creep analysis has two inflections corresponding to the cyclic and monotonic strengths. These inflections separate three domains on the long-term strength curve, which are characterised by different creep fracture modes and creep deformation mechanisms. Therefore, safe creep design is guaranteed in the linear creep domain with brittle failure mode defined by the cyclic yielding. These assumptions are confirmed using three structural steels for normal and high-temperature applications. The advantage of using cyclic yield strength for characterisation of fatigue and creep strength is a relatively quick experimental identification. The total duration of cyclic tests for a cyclic stress-strain curve identification is much less than the typical durations of fatigue and creep rupture tests at the stress levels around the cyclic yield strength.

Effect of cyclic electron irradiation on mechanical properties of austenite steel

International Nuclear Information System (INIS)

Tsepelev, A.B.; Sadykhov, S.I.O.; Chernov, A.I.; Sevost'yanov, M.A.

2006-01-01

To check the supposition on the possibility of radiation-stimulated process enhancement under cyclic irradiation conditions an experimental investigation is carried out to elucidate the effect of the mode of irradiation (continuous or cyclic) on mechanical properties of chromium-manganese austenitic stainless steel type 10Kh12G20V. The effect of some radiation hardening is observed under cyclic irradiation, however, the data obtained cannot be considered as good evidence for the validity of proposed model of dynamic preference if the scatter in experimental data is taken into account [ru

Hierarchical assembly of branched supramolecular polymers from (cyclic Peptide)-polymer conjugates.

Science.gov (United States)

Koh, Ming Liang; Jolliffe, Katrina A; Perrier, Sébastien

2014-11-10

We report the synthesis and assembly of (N-methylated cyclic peptide)-polymer conjugates for which the cyclic peptide is attached to either the α- or both α- and ω- end groups of a polymer. A combination of chromatographic, spectroscopic, and scattering techniques reveals that the assembly of the conjugates follows a two-level hierarchy, initially driven by H-bond formation between two N-methylated cyclic peptides, followed by unspecific, noncovalent aggregation of this peptide into small domains that behave as branching points and lead to the formation of branched supramolecular polymers.

Experimental study on uniaxial cyclic ratcheting behavior of 304 stainless steel at room temperature

International Nuclear Information System (INIS)

Yang Xianjie; Gao Qing; Cai Lixun; Liu Yujie

2004-01-01

The cyclic tests for 304 stainless steel with solution heat treatment under uni-axial cyclic straining and stressing were carried out systematically. The effects of the cyclic engineering stress amplitude history with constant mean stress, the mean engineering stress history with constant cyclic stress amplitude and the stress amplitude histories with the specific mean stress increment per cycle on the uni-axial ratcheting deformation behavior were investigated. Some significant results are obtained

Topology and symmetry of surface Majorana arcs in cyclic superconductors

Science.gov (United States)

Mizushima, Takeshi; Nitta, Muneto

2018-01-01

We study the topology and symmetry of surface Majorana arcs in superconductors with nonunitary "cyclic" pairing. Cyclic p -wave pairing may be realized in a cubic or tetrahedral crystal, while it is a candidate for the interior P32 superfluids of neutron stars. The cyclic state is an admixture of full gap and nodal gap with eight Weyl points and the low-energy physics is governed by itinerant Majorana fermions. We here show the evolution of surface states from Majorana cone to Majorana arcs under rotation of surface orientation. The Majorana cone is protected solely by an accidental spin rotation symmetry and fragile against spin-orbit coupling, while the arcs are attributed to two topological invariants: the first Chern number and one-dimensional winding number. Lastly, we discuss how topologically protected surface states inherent to the nonunitary cyclic pairing can be captured from surface probes in candidate compounds, such as U1 -xThxBe13 . We examine tunneling conductance spectra for two competitive scenarios in U1 -xThxBe13 —the degenerate Eu scenario and the accidental scenario.

Cyclic antibiotic therapy for diverticular disease: a critical reappraisal.

Science.gov (United States)

Zullo, Angelo; Hassan, Cesare; Maconi, Giovanni; Manes, Gianpiero; Tammaro, Gianfranco; De Francesco, Vincenzo; Annibale, Bruno; Ficano, Leonardo; Buri, Luigi; Gatto, Giovanni; Lorenzetti, Roberto; Campo, Salvatore M; Ierardi, Enzo; Pace, Fabio; Morini, Sergio

2010-09-01

Different symptoms have been attributed to uncomplicated diverticular disease (DD). Poor absorbable antibiotics are largely used for uncomplicated DD, mainly for symptom treatment and prevention of diverticulitis onset. Controlled trials on cyclic administration of rifaximin in DD patients were evaluated. Four controlled, including 1 double-blind and 3 open-label, randomized studies were available. Following a long-term cyclic therapy, a significant difference emerged in the global symptoms score (range: 0-18) between rifaximin plus fibers (from 6-6.5 to 1-2) and fibers alone (from 6.7 to 2-3.8), although the actual clinically relevance of such a very small difference remains to be ascertained. Moreover, a similar global symptom score reduction (from 6 to 2.4) can be achieved by simply recommending an inexpensive high-fiber diet. Current data suggest that cyclic rifaximin plus fibers significantly reduce the incidence of the first episode of acute diverticulitis as compared to fibers alone (1.03% vs 2.75%), but a cost-efficacy analysis is needed before this treatment can be routinely recommended. The available studies have been hampered by some limitations, and definite conclusions could not be drawn. The cost of a long-life, cyclic rifaximin therapy administered to all symptomatic DD patients would appear prohibitive.

Cyclic delivery scheduling to customers with different priorities

Directory of Open Access Journals (Sweden)

Katarzyna Zofia Gdowska

2013-12-01

Full Text Available Background: In this paper a cyclic delivery scheduling problem for customers with different priorities is presented. Shops, which are provided with deliveries, are occasionally located in places which are crucial for the proper flow of traffic. In such places coordination of deliveries is crucial; therefore it allows to completely eliminate the phenomenon of the simultaneous arrivals of suppliers. Methods: In this paper the cyclic delivery scheduling problem for customers with different priorities was presented. To this theoretical problem a mix integer programming model was developed. Specific approach to the cyclic delivery scheduling problem is inspired by timetabling problem for urban public transport. Results: Mixed integer programming model was employed for solving four cases of cyclic delivery scheduling problem for customers with different priorities. When the value of the synchronization priority assigned to a single customer raised then the total number of synchronizations in the whole network decreased. In order to compare solutions a synchronization rate was utilized. A simple factor was utilized - the proportion of number of synchronizations of deliveries to a given customer to the total number of synchronizations obtained for the whole network. When the value of synchronization priority raised then the value of synchronization rate of this customer improved significantly. Conclusions: The mixed integer programming model for the cyclic delivery scheduling problem for customers with different priorities presented in this paper can be utilized for generating schedules of serving customers located in places where only one delivery can be received and unloaded at one go and where there is no space for other suppliers to wait in a queue. Such a schedule can be very useful for organizing deliveries to small shops united in a franchising network, since they operate in a way that is very similar to the network presented in this paper

Novel cyclic di-GMP effectors of the YajQ protein family control bacterial virulence.

Directory of Open Access Journals (Sweden)

Shi-qi An

2014-10-01

Full Text Available Bis-(3',5' cyclic di-guanylate (cyclic di-GMP is a key bacterial second messenger that is implicated in the regulation of many critical processes that include motility, biofilm formation and virulence. Cyclic di-GMP influences diverse functions through interaction with a range of effectors. Our knowledge of these effectors and their different regulatory actions is far from complete, however. Here we have used an affinity pull-down assay using cyclic di-GMP-coupled magnetic beads to identify cyclic di-GMP binding proteins in the plant pathogen Xanthomonas campestris pv. campestris (Xcc. This analysis identified XC_3703, a protein of the YajQ family, as a potential cyclic di-GMP receptor. Isothermal titration calorimetry showed that the purified XC_3703 protein bound cyclic di-GMP with a high affinity (K(d∼2 µM. Mutation of XC_3703 led to reduced virulence of Xcc to plants and alteration in biofilm formation. Yeast two-hybrid and far-western analyses showed that XC_3703 was able to interact with XC_2801, a transcription factor of the LysR family. Mutation of XC_2801 and XC_3703 had partially overlapping effects on the transcriptome of Xcc, and both affected virulence. Electromobility shift assays showed that XC_3703 positively affected the binding of XC_2801 to the promoters of target virulence genes, an effect that was reversed by cyclic di-GMP. Genetic and functional analysis of YajQ family members from the human pathogens Pseudomonas aeruginosa and Stenotrophomonas maltophilia showed that they also specifically bound cyclic di-GMP and contributed to virulence in model systems. The findings thus identify a new class of cyclic di-GMP effector that regulates bacterial virulence.

Cyclic Oxidation and Hot Corrosion of NiCrY-Coated Disk Superalloys

Science.gov (United States)

Gabb, Timothy P.; Miller, Robert A.; Sudbrack, Chantal K.; Draper, Susan L.; Nesbitt, James A.; Rogers, Richard B.; Telesman, Ignacy; Ngo, Vanda; Healy, Jonathan

2016-01-01

Powder metallurgy disk superalloys have been designed for higher engine operating temperatures through improvement of their strength and creep resistance. Yet, increasing disk application temperatures to 704 degrees Centigrade and higher could enhance oxidation and activate hot corrosion in harmful environments. Protective coatings could be necessary to mitigate such attack. Cylindrical coated specimens of disk superalloys LSHR and ME3 were subjected to thermal cycling to produce cyclic oxidation in air at a maximum temperature of 760 degrees Centigrade. The effects of substrate roughness and coating thickness on coating integrity after cyclic oxidation were considered. Selected coated samples that had cyclic oxidation were then subjected to accelerated hot corrosion tests. This cyclic oxidation did not impair the coating's resistance to subsequent hot corrosion pitting attack.

Cyclic Oxidation and Hot Corrosion of NiCrY-Coated Disk Superalloy

Science.gov (United States)

Gabb, Tim; Miller, R. A.; Sudbrack, C. K.; Draper, S. L.; Nesbitt, J.; Telesman, J.; Ngo, V.; Healy, J.

2015-01-01

Powder metallurgy disk superalloys have been designed for higher engine operating temperatures through improvement of their strength and creep resistance. Yet, increasing disk application temperatures to 704 C and higher could enhance oxidation and activate hot corrosion in harmful environments. Protective coatings could be necessary to mitigate such attack. Cylindrical coated specimens of disk superalloys LSHR and ME3 were subjected to thermal cycling to produce cyclic oxidation in air at a maximum temperature of 760 C. The effects of substrate roughness and coating thickness on coating integrity after cyclic oxidation were considered. Selected coated samples that had cyclic oxidation were then subjected to accelerated hot corrosion tests. The effects of this cyclic oxidation on resistance to subsequent hot corrosion attack were examined.

Cyclic testing of thin Ni films on a pre-tensile compliant substrate

Energy Technology Data Exchange (ETDEWEB)

Wei, He [Department of Mechanics, Tianjin University, 135 Yaguan Rd, Jinnan, 300350 Tianjin (China); Département Physique et Mécanique d es Matériaux, Institut Pprime, CNRS–Université de Poitiers, Bd Marie et Pierre Curie, Futuroscope, 86962 (France); Renault, Pierre-Olivier, E-mail: pierre.olivier.renault@univ-poitiers.fr [Département Physique et Mécanique d es Matériaux, Institut Pprime, CNRS–Université de Poitiers, Bd Marie et Pierre Curie, Futuroscope, 86962 (France); Bourhis, Eric Le [Département Physique et Mécanique d es Matériaux, Institut Pprime, CNRS–Université de Poitiers, Bd Marie et Pierre Curie, Futuroscope, 86962 (France); Wang, Shibin [Department of Mechanics, Tianjin University, 135 Yaguan Rd, Jinnan, 300350 Tianjin (China); Goudeau, Philippe [Département Physique et Mécanique d es Matériaux, Institut Pprime, CNRS–Université de Poitiers, Bd Marie et Pierre Curie, Futuroscope, 86962 (France)

2017-05-17

A novel experimental approach to study the cyclic plastic deformation of thin metallic films is presented. 300 nm thick Ni films are deposited on both sides of a pre-tensile soft substrate which allows to deform the films alternately in tension and compression (approximately from +2.7 GPa down to −2 GPa) relative to the as-deposited residual stress state. Nanocrystalline thin films' intrinsic elastic strains (or stresses) and true strains have been measured step by step during two loading/unloading cycles thanks to the X-ray diffraction (XRD) and digital image correlation (DIC) techniques respectively. From the first cyclic deformation, a significant Bauschinger effect is evidenced in the films, however, little or no cyclic hardening is observed during the two cyclic tests.

Structure-activity studies of vasoactive intestinal peptide (VIP): cyclic disulfide analogs.

Science.gov (United States)

Bolin, D R; Cottrell, J; Garippa, R; O'Neill, N; Simko, B; O'Donnell, M

1993-02-01

Analogs of vasoactive intestinal peptide with cysteine residues incorporated at selected sites within the sequence were prepared by solid phase methods, oxidized to the corresponding cyclic disulfides and purified to homogeneity by preparative HPLC. The cyclic compounds were assayed as smooth muscle relaxants on isolated guinea pig trachea, as bronchodilators in vivo in guinea pigs, and for binding to VIP receptors in guinea pig lung membranes. Of the analogs prepared at the N-terminus, one compound, Ac-[D-Cys6,D-Cys11,Lys12,Nle17,Val26,Th r28]-VIP, was found to be a full agonist with slightly more than one tenth the potency of native VIP. Most other cyclic analogs in the N-terminal region were found to be inactive. A second analog, Ac-[Lys12,Cys17,Val26,Cys28]-VIP, was also found to be a full agonist with potency about one third that of native VIP. Furthermore, this compound was active as a bronchodilator in vivo in guinea pig, but with somewhat diminished potency as compared to native VIP. Strikingly, this cyclic compound was found to have significantly longer duration of action (> 40 min) when compared to an analogous acyclic compound (5 min). The conformational restrictions imposed by formation of the cyclic ring structures may have stabilized the molecule to degradation, thus enhancing the effective duration of action. Analysis of this series of cyclic analogs has also yielded information about the requirements for the receptor-active conformation of VIP.

Effects of fenspiride on human bronchial cyclic nucleotide phosphodiesterase isoenzymes: functional and biochemical study.

Science.gov (United States)

Cortijo, J; Naline, E; Ortiz, J L; Berto, L; Girard, V; Malbezin, M; Advenier, C; Morcillo, E J

1998-01-02

We have investigated the role of human bronchial cyclic nucleotide phosphodiesterases in the effects of fenspiride, a drug endowed with bronchodilator and anti-inflammatory properties. Functional studies on human isolated bronchi showed that fenspiride (10(-6)-3 x 10(-3) M, 30 min) induced a shift to the left of the concentration-response curves for isoprenaline and sodium nitroprusside with -logEC50 values of 4.1+/-0.1 (n = 7) and 3.5+/-0.2 (n = 8), respectively. Biochemical studies were carried out on three human bronchi in which separation of cyclic nucleotide phosphodiesterase isoenzymes was performed by ion exchange chromatography followed by determination of phosphodiesterase activity with a radioisotopic method. Phosphodiesterase 4 (cyclic AMP-specific) and phosphodiesterase 5 (cyclic GMP-specific) were the major phosphodiesterase isoforms present in the human bronchial tissue. The presence of phosphodiesterase 1 (Ca2+/calmodulin-stimulated), phosphodiesterase 2 (cyclic GMP-stimulated) and, in two cases, phosphodiesterase 3 (cyclic GMP-inhibited) was also identified. Fenspiride inhibited phosphodiesterase 4 and phosphodiesterase 3 activities with -logIC50 values of 4.16+/-0.09 and 3.44+/-0.12, respectively. Phosphodiesterase 5 activity was also inhibited with a -logIC50 value of approximately 3.8. Fenspiride (fenspiride is an effective inhibitor of both cyclic AMP and cyclic GMP hydrolytic activity in human bronchial tissues and this action may contribute to its airway effects.

Levels of cyclic-2,3-diphosphoglycerate in Methanobacterium thermoautotrophicum during phosphate limitation.

OpenAIRE

Seely, R J; Fahrney, D E

1984-01-01

Batch-grown Methanobacterium thermoautotrophicum cells grew nonexponentially in the absence of exogenous Pi until intracellular cyclic-2,3-diphosphoglycerate (cyclic DPG) had fallen below 2 mumol/g (dry weight), the limit of detection. Growth resumed immediately upon transfer to medium containing Pi Cyclic DPG levels were also below detection in Pi-limited chemostat cultures operating at a dilution rate of 0.173 h-1 (4-h doubling time), with reservoir Pi concentrations below 200 microM. At th...

Cyclic Triaxial Tests on Eastern Scheldt Sand with Three Different Densities

DEFF Research Database (Denmark)

Jakobsen, Kim Parsberg

This report contains the results of numerous cyclic triaxial tests performed within the framework of the project "Probabilistic Design Tools for Vertical Breakwaters (PROVERBS), MAST III". The performed tests constitute a part of an established data base to be used to estimate the undrained cyclic...

Holocene glacier fluctuations inferred from lacustrine sediment, Emerald Lake, Kenai Peninsula, Alaska

Science.gov (United States)

LaBrecque, Taylor S.; Kaufman, Darrell S.

2016-01-01

Physical and biological characteristics of lacustrine sediment from Emerald Lake were used to reconstruct the Holocene glacier history of Grewingk Glacier, southern Alaska. Emerald Lake is an ice-marginal threshold lake, receiving glaciofluvial sediment when Grewingk Glacier overtops the topographic divide that separates it from the lake. Sub-bottom acoustical profiles were used to locate core sites to maximize both the length and resolution of the sedimentary sequence recovered in the 4-m-long cores. The age model for the composite sequence is based on 13 14C ages and a 210Pb profile. A sharp transition from the basal inorganic mud to organic-rich mud at 11.4 ± 0.2 ka marks the initial retreat of Grewingk Glacier below the divide of Emerald Lake. The overlaying organic-rich mud is interrupted by stony mud that records a re-advance between 10.7 ± 0.2 and 9.8 ± 0.2 ka. The glacier did not spill meltwater into the lake again until the Little Ice Age, consistent with previously documented Little Ice Ages advances on the Kenai Peninsula. The retreat of Grewingk Glacier at 11.4 ka took place as temperature increased following the Younger Dryas, and the subsequent re-advance corresponds with a climate reversal beginning around 11 ka across southern Alaska.

Cyclic Elastoplastic Performance of Aluminum 7075-T6 Under Strain- and Stress-Controlled Loading

Science.gov (United States)

Agius, Dylan; Wallbrink, Chris; Kourousis, Kyriakos I.

2017-12-01

Elastoplastic investigations of aerospace aluminum are important in the development of an understanding of the possible cyclic transient effects and their contribution to the material performance under cyclic loading. Cyclic plasticity can occur in an aerospace aluminum component or structure depending on the loading conditions and the presence of external and internal discontinuities. Therefore, it is vital that the cyclic transient effects of aerospace aluminum are recognized and understood. This study investigates experimentally the cyclic elastoplastic performance of aluminum 7075-T6 loaded in symmetric strain control, and asymmetric stress and strain control. A combination of cyclic hardening and softening was noticed from high strain amplitude symmetric strain-controlled tests and at low stress amplitude asymmetric stress-controlled tests. From asymmetric strain control results, the extent of mean stress relaxation depended on the size of the strain amplitude. Additionally, saturation of the ratcheting strain (plastic shakedown) was also found to occur during asymmetric stress control tests. The experimental results were further analyzed using published microstructure research from the past two decades to provide added explanation of the micro-mechanism contribution to the cyclic transient behavior.

K-theory and periodic cyclic homology of some noncompact quantum algebras

International Nuclear Information System (INIS)

Do Ngoc Diep; Kuku, Aderemi O.

2003-07-01

We prove in this paper that the periodic cyclic homology of the quantized algebras of functions on coadjoint orbits of connected and simply connected Lie group, are isomorphic to the periodic cyclic homology of the quantized algebras of functions on coadjoint orbits of compact maximal subgroups, without localization. Some noncompact quantum groups and algebras were constructed and their irreducible representations were classified in recent works of Do Ngoc Diep and Nguyen Viet Hai [DH1]-[DH2] and Do Due Hanh [DD] by using deformation quantization. In this paper we compute their K-groups, periodic cyclic homology groups and their Chern characters. (author)

Inverse strain rate effect on cyclic stress response in annealed Zircaloy-2

Energy Technology Data Exchange (ETDEWEB)

Sudhakar Rao, G.; Verma, Preeti [Center of Advanced Study, Department of Metallurgical Engineering, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India); Chakravartty, J.K. [Mechanical Metallurgy Group, Bhabha Atomic Research Center, Trombay 400 085, Mumbai (India); Nudurupati, Saibaba [Nuclear Fuel Complex, Hyderabad 500 062 (India); Mahobia, G.S.; Santhi Srinivas, N.C. [Center of Advanced Study, Department of Metallurgical Engineering, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India); Singh, Vakil, E-mail: vsingh.met@itbhu.ac.in [Center of Advanced Study, Department of Metallurgical Engineering, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India)

2015-02-15

Low cycle fatigue behavior of annealed Zircaloy-2 was investigated at 300 and 400 °C at different strain amplitudes and strain rates of 10{sup −2}, 10{sup −3}, and 10{sup −4} s{sup −1}. Cyclic stress response showed initial hardening with decreasing rate of hardening, followed by linear cyclic hardening and finally secondary hardening with increasing rate of hardening for low strain amplitudes at both the temperatures. The rate as well the degree of linear hardening and secondary hardening decreased with decrease in strain rate at 300 °C, however, there was inverse effect of strain rate on cyclic stress response at 400 °C and cyclic stress was increased with decrease in strain rate. The fatigue life decreased with decrease in strain rate at both the temperatures. The occurrence of linear cyclic hardening, inverse effect of strain rate on cyclic stress response and deterioration in fatigue life with decrease in strain rate may be attributed to dynamic strain aging phenomena resulting from enhanced interaction of dislocations with solutes. Fracture surfaces revealed distinct striations, secondary cracking, and oxidation with decrease in strain rate. Deformation substructure showed parallel dislocation lines and dislocation band structure at 300 °C. Persistent slip band wall structure and development of fine Corduroy structure was observed at 400 °C.

Inverse strain rate effect on cyclic stress response in annealed Zircaloy-2

International Nuclear Information System (INIS)

Sudhakar Rao, G.; Verma, Preeti; Chakravartty, J.K.; Nudurupati, Saibaba; Mahobia, G.S.; Santhi Srinivas, N.C.; Singh, Vakil

2015-01-01

Low cycle fatigue behavior of annealed Zircaloy-2 was investigated at 300 and 400 °C at different strain amplitudes and strain rates of 10 −2 , 10 −3 , and 10 −4 s −1 . Cyclic stress response showed initial hardening with decreasing rate of hardening, followed by linear cyclic hardening and finally secondary hardening with increasing rate of hardening for low strain amplitudes at both the temperatures. The rate as well the degree of linear hardening and secondary hardening decreased with decrease in strain rate at 300 °C, however, there was inverse effect of strain rate on cyclic stress response at 400 °C and cyclic stress was increased with decrease in strain rate. The fatigue life decreased with decrease in strain rate at both the temperatures. The occurrence of linear cyclic hardening, inverse effect of strain rate on cyclic stress response and deterioration in fatigue life with decrease in strain rate may be attributed to dynamic strain aging phenomena resulting from enhanced interaction of dislocations with solutes. Fracture surfaces revealed distinct striations, secondary cracking, and oxidation with decrease in strain rate. Deformation substructure showed parallel dislocation lines and dislocation band structure at 300 °C. Persistent slip band wall structure and development of fine Corduroy structure was observed at 400 °C

Influences of cyclic deformation on creep property and creep-fatigue life prediction considering them

International Nuclear Information System (INIS)

Takahashi, Yukio

2009-01-01

Evaluation of creep-fatigue is essential in design and life management of high-temperature components in power generation plants. Cyclic deformation may alter creep property of the materials and its consideration may improve predictability of creep-fatigue failure life. To understand them, creep tests were conducted for the materials subjected to cyclic loading and their creep rupture and deformation behaviors were compared with those of as-received materials. Both 316FR and modified 9Cr-1Mo steel were tested. (1) Creep rupture time and elongation generally tend to decrease with cyclic loading in both materials, and especially elongation of 316FR drastically decreases by being cyclically deformed. (2) Amount of primary creep deformation decreases by cyclic loading and the ways to improve its predictability were developed. (3) Use of creep rupture ductility after cyclic deformation, instead of that of as-received material, brought about clear improvement of life prediction in a modified ductility exhaustion approach. (author)

Paediatric cyclical Cushing's disease due to corticotroph cell hyperplasia.

LENUS (Irish Health Repository)

Noctor, E

2015-06-01

Cushing\\'s disease is very rare in the paediatric population. Although uncommon, corticotroph hyperplasia causing Cushing\\'s syndrome has been described in the adult population, but appears to be extremely rare in children. Likewise, cyclical cortisol hypersecretion, while accounting for 15 % of adult cases of Cushing\\'s disease, has only rarely been described in the paediatric population. Here, we describe a very rare case of a 13-year old boy with cyclical cortisol hypersecretion secondary to corticotroph cell hyperplasia.

Microgravity changes in heart structure and cyclic-AMP metabolism

Science.gov (United States)

Philpott, D. E.; Fine, A.; Kato, K.; Egnor, R.; Cheng, L.

1985-01-01

The effects of microgravity on cardiac ultrastructure and cyclic AMP metabolism in tissues of rats flown on Spacelab 3 are reported. Light and electron microscope studies of cell structure, measurements of low and high Km phosphodiesterase activity, cyclic AMP-dependent protein kinase activity, and regulatory subunit compartmentation show significant deviations in flight animals when compared to ground controls. The results indicate that some changes have occurred in cellular responses associated with catecholamine receptor interactions and intracellular signal processing.

Relation of intracellular cyclic AMP to the shape of mammalian cell survival curves

International Nuclear Information System (INIS)

Lehnert, S.

1975-01-01

Results of experiments with V79 cells growing in tissue culture indicate that the reproductive survival of cells following irradiation is influenced by the level of intracellular 3', 5'-cyclic adenosine monophosphate (cyclic AMP) at the time of irradiation. Cells containing high levels of cyclic AMP induced by treatments with drugs show a characteristic survival curve in which the extent of the shoulder is increased so that the survival after low doses is enhanced. The exponential slope or D 0 , however, is decreased so that at high doses the survival of cells containing high levels of cyclic AMP may be less than that of controls. Naturally occurring changes in radiosensitivity such as those observed as cells pass through the division cycle, may also be related to parallel changes in cyclic AMP concentration occurring during the cycle. Injection of mice with compounds producing elevated cyclic AMP prior to whole-body irradiation increases survival at seven days post-irradiation. The shape of the survival curve for intestinal stem cells in these mice differs from that of the control in having an increased extrapolation number; no change in D 0 is observed in this in vivo situation. (author)

Cyclic and Explosive Evaluation of New Proposed Steel Joint

Directory of Open Access Journals (Sweden)

Iman Faridmehr

2016-01-01

Full Text Available The behaviour of a novel steel beam-to-column connection, the saddlebag, subjected to cyclic and progressive collapse, was evaluated in this paper. The cyclic behaviour considered the interstory drift angle and flexural strength in accordance with 2010 AISC Seismic Provisions, while progressive collapse assessment was evaluated through the plastic hinge rotation angle based on acceptance criteria provided in the UFC 4-023-03 guideline. From the cyclic test, one complete cycle of an interstory drift angle of 0.06 rad was satisfied for the saddlebag connection, which is an indication of the effectiveness in accordance with 2010 AISC Seismic Provisions. Besides, the new proposed connection developed adequate catenary action, which is a fundamental criterion to resist against progressive collapse. The resulting fuller hysteretic loops with large energy dissipation capacity in the proposed saddlebag connection guarantee its ability to address the inelastic deformation demands in earthquake conditions.

Classification of cyclic initial states and geometric phase for the spin-j system

Energy Technology Data Exchange (ETDEWEB)

Skrynnikov, N.R.; Zhou, J.; Sanctuary, B.C. [Dept. of Chem., McGill Univ., Montreal, PQ (Canada)

1994-09-21

Quantum states which evolve cyclically in their projective Hilbert space give rise to a geometric (or Aharonov-Anandan) phase. An aspect of primary interest is stable cyclic behaviour as realized under a periodic Hamiltonian. The problem has been handled by use of time-dependent transformations treated along the lines of Floquet's theory as well as in terms of exponential operators with a goal to examine the variety of initial states exhibiting cyclic behaviour. A particular case of special cyclic initial states is described which is shown to be important for nuclear magnetic resonance experiments aimed at the study of the effects of the geometric phase. An example of arbitrary spin j in a precessing magnetic field and spin j=1 subject to both axially symmetric quadrupolar interaction and a precessing magnetic field are presented. The invariant (Kobe's) geometric phase is calculated for special cyclic states. (author)

Behavior of prestressed concrete subjected to low temperatures and cyclic loading

International Nuclear Information System (INIS)

Berner, D.E.

1984-01-01

Concrete has exhibited excellent behavior in cryogenic containment vessels for several decades under essentially static conditions. Tests were conducted to determine the response of prestressed lightweight concrete subjected to high-intensity cyclic loading and simultaneous cryogenic thermal shock, simulating the relatively dynamic conditions encountered offshore or in seismic areas. Lightweight concrete has several attractive properties for cryogenic service including: (1) very low permeability, (2) good strain capacity, (3) relatively low thermal conductivity, and (4) a low modulus of elasticity. Experimental results indicated that the mechanical properties of plain lightweight concrete significantly increase with moisture content at low temperatures, while cyclic loading fatigue effects are reduced at low temperatures. Also, tests on uniaxially and on biaxially prestressed lightweight concrete both indicate that the test specimens performed well under severe cyclic loading and cryogenic thermal shock with only moderate reduction in flexural stiffness. Supplementary tests conducted in this study indicate that conventionally reinforced concrete degrades significantly faster than prestressed concrete when subjected to cyclic loading and thermal shock

Aspirin effects on lymphocyte cyclic AMP levels in normal human subjects.

Science.gov (United States)

Snider, D E; Parker, C W

1976-01-01

In purified lymphocytes from the peripheral blood of healthy human subjects who had ingested therapeutic doses of aspirin, there was a significant decrease in resting cyclic AMP levels as well as a partial inhibition of the rise in cyclic AMP with isoproterenol or prostaglandin E1. These changes were seen as early as 30 min after aspirin ingestion and did not appear to result from aspirin effects on lymphocyte recovery, purity, viability, or relative number of thymus- or bone marrow-derived lymphocytes. In contrast, the direct addition of aspirin to suspensions of purified peripheral lymphocytes did not significantly alter their cyclic AMP levels. However, an effect of aspirin could be obtained in vitro if aspirin was added to unprocessed whole blood during the dextran sedimentation phase of the cell purification. Thus the effect of aspirin on lymphocyte cyclic AMP metabolism, may be indirect, through other cells present in the peripheral blood. PMID:182720

Cyclic electron flow is redox-controlled but independent of state transition.

Science.gov (United States)

Takahashi, Hiroko; Clowez, Sophie; Wollman, Francis-André; Vallon, Olivier; Rappaport, Fabrice

2013-01-01

Photosynthesis is the biological process that feeds the biosphere with reduced carbon. The assimilation of CO2 requires the fine tuning of two co-existing functional modes: linear electron flow, which provides NADPH and ATP, and cyclic electron flow, which only sustains ATP synthesis. Although the importance of this fine tuning is appreciated, its mechanism remains equivocal. Here we show that cyclic electron flow as well as formation of supercomplexes, thought to contribute to the enhancement of cyclic electron flow, are promoted in reducing conditions with no correlation with the reorganization of the thylakoid membranes associated with the migration of antenna proteins towards Photosystems I or II, a process known as state transition. We show that cyclic electron flow is tuned by the redox power and this provides a mechanistic model applying to the entire green lineage including the vast majority of the cases in which state transition only involves a moderate fraction of the antenna.

Experimental investigation of steel fiber-reinforced concrete beams under cyclic loading

Science.gov (United States)

Ranjbaran, Fariman; Rezayfar, Omid; Mirzababai, Rahmatollah

2018-03-01

An experimental study has been conducted to study the cyclic behavior of reinforced concrete beams in which steel fibers were added to the concrete mix. Seven similar geometrically specimens in full scale were studied under four- point bending test in the form of slow cyclic loading. One sample as a control specimen was made without steel fibers or 0% volume fraction (vf) and six other samples with 1, 2 and 4% vf of steel fibers in twin models. The maximum and ultimate resistance, ductility, degradation of loading and unloading stiffness, absorption and dissipation of energy and equivalent viscous damping were studied in this investigation and the effect of steel fibers on the cyclic behavior was compared with each other. Generally, the addition of steel fibers up to a certain limit value (vf = 2%) improves the cyclic behavior of reinforced concrete beams and results in the increase of maximum strength and ultimate displacement.

Effect of cyclic torsional preloading on cyclic fatigue resistance of ProTaper Next and Mtwo nickel–titanium instruments

Directory of Open Access Journals (Sweden)

Eugenio Pedullà

2015-06-01

Conclusions: Torsional preloads reduced the cyclic fatigue resistance of M-wire and conventional (as ProTaper Next and Mtwo NiTi rotary instruments except for Mtwo with 25% or 50% of torsional preloading.

Branched GDGTs in Lacustrine Environments: Tracing Allochthonous and Autochthonous Sources Using Compound-Specific Stable Carbon Isotope Analysis

Science.gov (United States)

Weber, Y.; S Sinninghe Damsté, J.; Lehmann, M. F.; Niemann, H.; Schubert, C. J.

2015-12-01

Branched glycerol dialkyl glycerol tetraethers (brGDGTs) are bacterial membrane lipids that are ubiquitous in soils and peat, as well as in sediments of lakes, rivers and coastal marine environments. It has been found that the distribution of brGDGTs changes systematically with ambient temperature and pH, attesting to their potential as proxy indicators for paleoclimatic reconstruction. In lacustrine sedimentary archives, brGDGTs can originate from two sources: (1) allochthonous soil organic matter and (2) autochthonous brGDGTs produced within the lake system, both of which display fairly distinct temperature-brGDGT relationships. Until now, disentangling the relative contribution of these sources was impossible, complicating the use of brGDGTs for quantitative paleotemperature reconstructions. BrGDGTs in soils display a narrow range with respect to their stable carbon isotope composition (δ13C), generally between -27 and -30 ‰, whereas we recently found contrasting δ13C values as low as -43 ‰ to -46 ‰ for brGDGTs in sediments of a small Alpine lake. To trace the origin of this distinct isotope signal, we determined the 13C content of brGDGTs in suspended particulate matter (SPM) from the water column of Lake Lugano (Switzerland). The δ13C of SPM-derived brGDGTs decreased systematically from -34 ‰ in the mixolimnion to -41 ‰ in the anoxic monimolimnion of Lake Lugano, providing evidence for aquatic in situ production of 13C-depleted brGDGT. In order to study whether the negative δ13C offset of water column- vs. soil-derived brGDGTs may serve as an indicator for lacustrine brGDGT production, we also analyzed surface sediments from 36 lakes across the Alpine Region. In most (~85 %) of the studied lake sediments, the δ13C of brGDGTs ranged between -34 ‰ and -45 ‰, indicating predominance or a substantial contribution of aquatically produced brGDGTs. However, in some lakes (~15 %) δ13C values between -27 ‰ and -30 ‰ suggest a mainly

Experimental study under uniaxial cyclic behavior at room and high temperature of 316L stainless steel

International Nuclear Information System (INIS)

Kang Guozheng; Gao Qing; Yang Xianjie; Sun Yafang

2001-01-01

An experimental study was carried out of the cyclic properties of 316L stainless steel subjected to uniaxial strain and stress at room and high temperature. The effects of cyclic strain amplitude, temperature and their histories on the cyclic deformation behavior of 316L stainless steel are investigated. And, the influences of stress amplitude, mean stress, temperature and their histories on ratcheting are also analyzed. It is shown that either uniaxial cyclic property under cyclic strain or ratcheting under asymmetric uniaxial cyclic stress depends not only on the current temperature and loading state, but also on the previous temperature and loading history. Some significant results are obtained

Cyclic viscoelastoplasticity of polypropylene/nanoclay composites

DEFF Research Database (Denmark)

Drozdov, A.; Christiansen, Jesper de Claville

2012-01-01

Observations are reported on isotactic polypropylene/organically modified nanoclay hybrids with concentrations of filler ranging from 0 to 5 wt.% in cyclic tensile tests with a stress–controlled program (oscillations between various maximum stresses and the zero minimum stress). A pronounced effe...

Cyclic olefin copolymer-silica nanocomposites foams

Czech Academy of Sciences Publication Activity Database

Pegoretti, A.; Dorigato, A.; Biani, A.; Šlouf, Miroslav

2016-01-01

Roč. 51, č. 8 (2016), s. 3907-3916 ISSN 0022-2461 R&D Projects: GA MŠk(CZ) LO1507 Institutional support: RVO:61389013 Keywords : cyclic olefin copolymer * nanocomposites * silica Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.599, year: 2016

Optimum Design and Operation of Cyclic Storage Systems; Lumped Approach

Directory of Open Access Journals (Sweden)

Leila Ostadrahimi

2007-01-01

Full Text Available Conjunctive use of surface and groundwater resources is a preferred approach in water resources management. Compared to dam construction, groundwater has certain advantages, among which are less costs, less sedimentation and evaporation, fewer water quality problems, and less social and cultural problems. To reduce the major problems associated with the development of large-scale surface impoundment systems, cyclic storage systems can be used as an alternative. A cyclic storage system (CYCS is an integrated interactive system consisting of two subsystems of surface water storage (reservoir and groundwater; this system together with artificial recharge is able to satisfy the predefined demands with rather high reliability. In order to optimize these systems, one must consider the hydraulic interactions between all the components, but unfortunately it has been neglected in many studies. In this article, a nonlinear optimization model for design and operation of cyclic storage systems has been developed using the lumped approach. In order to evaluate the model, its results have been compared with the results of a model in which distributed approach had been deployed, and so the efficiency of lumped models to solve the problems of cyclic storage systems has been investigated.

A cyclic symmetry principle in physics

International Nuclear Information System (INIS)

Green, H.S.; Adelaide Univ., SA

1994-01-01

Many areas of modern physics are illuminated by the application of a symmetry principle, requiring the invariance of the relevant laws of physics under a group of transformations. This paper examines the implications and some of the applications of the principle of cyclic symmetry, especially in the areas of statistical mechanics and quantum mechanics, including quantized field theory. This principle requires invariance under the transformations of a finite group, which may be a Sylow π-group, a group of Lie type, or a symmetric group. The utility of the principle of cyclic invariance is demonstrated in finding solutions of the Yang-Baxter equation that include and generalize known solutions. It is shown that the Sylow π-groups have other uses, in providing a basis for a type of generalized quantum statistics, and in parametrising a new generalization of Lie groups, with associated algebras that include quantized algebras. 31 refs

Low-temperature resistance of cyclically strained aluminum

International Nuclear Information System (INIS)

Segal, H.R.; Richard, T.G.

1977-01-01

An experimental study of the resistance changes in high-purity, reinforced aluminum due to cyclic straining is presently underway. The purpose of this work is to determine the optimum purity of aluminum to be used as a stabilizing material for superconducting magnets used for energy storage. Since pure aluminum has a low yield strength, it is not capable of supporting the stress levels in an energized magnet. Therefore, it has been bonded to a high-strength material--in this case, 6061 aluminum alloy. This bonding permits pure aluminum to be strained cyclically beyond its elastic limit with recovery of large plastic strains upon release of the load. The resistance change in this composite material is less than that of pure, unreinforced aluminum

Cyclic GMP-AMP Displays Mucosal Adjuvant Activity in Mice

OpenAIRE

Škrnjug, Ivana; Guzmán, Carlos Alberto; Ruecker, Christine

2014-01-01

The recently discovered mammalian enzyme cyclic GMP-AMP synthase produces cyclic GMP-AMP (cGAMP) after being activated by pathogen-derived cytosolic double stranded DNA. The product can stimulate STING-dependent interferon type I signaling. Here, we explore the efficacy of cGAMP as a mucosal adjuvant in mice. We show that cGAMP can enhance the adaptive immune response to the model antigen ovalbumin. It promotes antigen specific IgG and a balanced Th1/Th2 lymphocyte response in immunized mice....

Theory of chromatography of partially cyclic polymers: Tadpole-type and manacle-type macromolecules.

Science.gov (United States)

Vakhrushev, Andrey V; Gorbunov, Alexei A

2016-02-12

A theory of chromatography is developed for partially cyclic polymers of tadpole- and manacle-shaped topological structures. We present exact equations for the distribution coefficient K at different adsorption interactions; simpler approximate formulae are also derived, relevant to the conditions of size-exclusion, adsorption, and critical chromatography. Theoretical chromatograms of heterogeneous partially cyclic polymers are simulated, and conditions for good separation by topology are predicted. According to the theory, an effective SEC-radius of tadpoles and manacles is mostly determined by the molar mass M, and by the linear-cyclic composition. In the interactive chromatography, the effect of molecular topology on the retention becomes significant. At the critical interaction point, partial dependences K(Mlin) and K(Mring) are qualitatively different: while being almost independent of Mlin, K increases with Mring. This behavior could be realized in critical chromatography-for separation of partially cyclic polymers by the number and molar mass of cyclic elements. Copyright © 2015 Elsevier B.V. All rights reserved.

Small-Scale Testing Rig for Long-Term Cyclically Loaded Monopiles in Cohesionless Soil

DEFF Research Database (Denmark)

Roesen, Hanne Ravn; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

2012-01-01

, and the period of the cyclic loading. However, the design guidance on these issues is limited. Thus, in order to investigate the pile behaviour for cyclically long-term loaded monopiles, a test setup for small-scale tests in saturated dense cohesionless soil is constructed and presented in here. The cyclic...... loading is applied mechanically by means of a testing rig, where the important input parameters: mean level, amplitude, number of cycles, and period of the loading can be varied. The results from a monotonic and a cyclic loading test on an open-ended aluminium pile with diameter = 100 mm and embedded...... length = 600 mm proves that the test setup is capable of applying the cyclic long-term loading. The plastic deformations during loading depend not only on the loading applied but also of the relative density of the soil and, thus, the tests are carried out with relative densities of 77-88%, i.e. similar...

Effect of cyclic plastic pre-strain on low cycle fatigue life

International Nuclear Information System (INIS)

Kanno, Satoshi; Nakane, Motoki; Yorikawa, Morio; Takagi, Yoshio

2010-01-01

In order to evaluate structural integrity of nuclear components subjected large seismic load which produce locally plastic strain, low cycle fatigue life was examined using cyclic plastic pre-strained materials of austenitic steel (SUS316, SUS316L, SUS304TP: JIS (Japanese Industrial Standards)) and ferritic steel (SFVQ1A, STS480, STPT410, SFVC2B, SS400: JIS). It was not found that cyclic plastic pre-strain up to range of 16%, 2.5 times affected on low cycle fatigue life. The validity of existing procedure of fatigue life estimation based on usage factor was confirmed when large seismic load brought nuclear materials cyclic plastic strain. (author)

Cyclic voltammetry and reduction mechanistic studies of ...

African Journals Online (AJOL)

styrylpyrylium perchlorates have been evaluated using cyclic voltammetry, in comparison to their non-methylated derivatives values. The reduction peak of all studied compounds remained chemically irreversible. The presence of the ...

Characterization of cyclical phases in the manufacturing industry in Spain

Directory of Open Access Journals (Sweden)

Mercè Sala

2014-09-01

Full Text Available 120 Purpose: The purpose of this paper is to characterize the cyclical phases of the manufacturing industry in Spain and detect which industries have more influence on the Spanish business cycle. We assume that economic growth is a priority; we are going to determine which industries have a more/less appropriate cyclical behavior according this priority. We analyze if the industries with better cyclical behavior are the ones that achieve greater co-movement with the business cycle of the Spanish economy, as this means they have a positive influence on economic activity. Design/methodology/approach: We examine the disaggregated quarterly IPI data of 16 manufacturing industries. Our methodology follows three steps. Firstly, we define cycle turning points; we follow the Harding and Pagan (2002 methodology. Secondly, we characterize the cyclical phases of the manufacturing industries in terms of duration, amplitude, deepness and steepness. We also determine the degree of inter-industrial cyclical synchronization and between industries in the cycle of the Spanish economy. This analysis is performed in two ways. On the one hand, we use the concordance index and the correlation coefficient. On the other hand, we work with indicators based on a consistency table. In the Third step, we apply a multi-objective methodology, specifically the compromise programming, to determine which industries have a more/less appropriate cyclical behavior according to the growth priority. Findings and Originality/value: The business cycle of the Spanish economy is positively influenced by high- and medium-tech industries, which have demonstrated their competitive capacity in international markets, and by medium- low-tech industries, with major strengths in R&D, and in survival and consolidation strategies. These results enable manufacturing industries to exert a positive effect on the business cycle that is weakened because many of them show a high correlation between

Hopf Algebroids and Their Cyclic Theory

NARCIS (Netherlands)

Kowalzig, N.

2009-01-01

The main objective of this thesis is to clarify concepts of generalised symmetries in noncommutative geometry (i.e., the noncommutative analogue of groupoids and Lie algebroids) and their associated (co)homologies. These ideas are incorporated by the notion of Hopf algebroids and Hopf-cyclic

Cyclic GMP-AMP displays mucosal adjuvant activity in mice.

Directory of Open Access Journals (Sweden)

Ivana Škrnjug

Full Text Available The recently discovered mammalian enzyme cyclic GMP-AMP synthase produces cyclic GMP-AMP (cGAMP after being activated by pathogen-derived cytosolic double stranded DNA. The product can stimulate STING-dependent interferon type I signaling. Here, we explore the efficacy of cGAMP as a mucosal adjuvant in mice. We show that cGAMP can enhance the adaptive immune response to the model antigen ovalbumin. It promotes antigen specific IgG and a balanced Th1/Th2 lymphocyte response in immunized mice. A characteristic of the cGAMP-induced immune response is the slightly reduced induction of interleukin-17 as a hallmark of Th17 activity--a distinct feature that is not observed with other cyclic di-nucleotide adjuvants. We further characterize the innate immune stimulation activity in vitro on murine bone marrow-derived dendritic cells and human dendritic cells. The observed results suggest the consideration of cGAMP as a candidate mucosal adjuvant for human vaccines.

Cyclic GMP-AMP displays mucosal adjuvant activity in mice.

Science.gov (United States)

Škrnjug, Ivana; Guzmán, Carlos Alberto; Rueckert, Christine; Ruecker, Christine

2014-01-01

The recently discovered mammalian enzyme cyclic GMP-AMP synthase produces cyclic GMP-AMP (cGAMP) after being activated by pathogen-derived cytosolic double stranded DNA. The product can stimulate STING-dependent interferon type I signaling. Here, we explore the efficacy of cGAMP as a mucosal adjuvant in mice. We show that cGAMP can enhance the adaptive immune response to the model antigen ovalbumin. It promotes antigen specific IgG and a balanced Th1/Th2 lymphocyte response in immunized mice. A characteristic of the cGAMP-induced immune response is the slightly reduced induction of interleukin-17 as a hallmark of Th17 activity--a distinct feature that is not observed with other cyclic di-nucleotide adjuvants. We further characterize the innate immune stimulation activity in vitro on murine bone marrow-derived dendritic cells and human dendritic cells. The observed results suggest the consideration of cGAMP as a candidate mucosal adjuvant for human vaccines.

Fatigue crack growth behavior under cyclic thermal transient stress

International Nuclear Information System (INIS)

Ueda, Masahiro; Kano, Takashi; Yoshitoshi, Atsushi.

1986-01-01

Thermal fatigue tests were performed using straight pipe specimens subjected to cyclic thermal shocks of liquid sodium, and crack growth behaviors were estimated using striation patterns observed clearly on any crack surface. Crack growth rate under cyclic thermal strain reaches the maximum at one depth, and after that it decreases gradually with crack depth. The peak location of crack growth rate becomes deeper by superposition of constant primary stress. Parallel cracks co-existing in the neighborhood move the peak to shallower location and decrease the maximum crack growth rate. The equivalent stress intensity factor range calculated by Walker's formula is successfully applied to the case of negative stress ratio. Fatigue crack growth rate under cyclic thermal strain agreed well with that under the constant temperature equal to the maximum value in the thermal cycle. Simplified methods for calculating the stress intensity factor and the crack interference factor have been developed. Crack growth behavior under thermal fatigue could be well predicted using numerical analysis results. (author)

Fatigue crack growth behavior under cyclic transient thermal stress

International Nuclear Information System (INIS)

Ueda, Masahiro; Kano, Takashi; Yoshitoshi, Atsushi.

1987-01-01

Thermal fatigue tests were performed using straight pipe specimens subjected to cyclic thermal shocks of liquid sodium, and crack growth behaviors were estimated using striation patterns observed clearly on any crack surface. Crack growth rate under cyclic thermal strain reaches the maximum at one depth, and after that it decreases gradually with crack depth. The peak location of crack growth rate becomes deeper by superposition of constant primary stress. Parallel cracks co-existing in the neighborhood move the peak to shallower location and decrease the maximum crack growth rate. The equivalent stress intensity factor range calculated by Walker's formula is successfully applied to the case of negative stress ratio. Fatigue crack growth rate under cyclic thermal strain agreed well with that under the constant temperature equal to the maximum value in the thermal cycle. Simplified methods for calculating the stress intensity factor and the crack interference factor have been developed. Crack growth behavior under thermal fatigue could be well predicted using numerical analysis results. (author)

Improving oral bioavailability of cyclic peptides by N-methylation.

Science.gov (United States)

Räder, Andreas F B; Reichart, Florian; Weinmüller, Michael; Kessler, Horst

2018-06-01

The renaissance of peptides in pharmaceutical industry results from their importance in many biological functions. However, low metabolic stability and the lack of oral availability of most peptides is a certain limitation. Whereas metabolic instability may be often overcome by development of small cyclic peptides containing d-amino acids, the very low oral availability of most peptides is a serious limitation for some medicinal applications. The situation is complicated because a twofold optimization - biological activity and oral availability - is required to overcome this problem. Moreover, most simple "rules" for achieving oral availability are not general and are applicable only to limited cases. Many structural modifications for increasing biological activities and metabolic stabilities of cyclic peptides have been described, of which N-alkylation is probably the most common. This mini-review focuses on the effects of N-methylation of cyclic peptides in strategies to optimize bioavailabilities. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Interactions between tetrathiafulvalene units in dimeric structures – the influence of cyclic cores

Directory of Open Access Journals (Sweden)

Huixin Jiang

2015-06-01

Full Text Available A selection of cyclic and acyclic acetylenic scaffolds bearing two tetrathiafulvalene (TTF units was prepared by different metal-catalyzed coupling reactions. The bridge separating the two TTF units was systematically changed from linearly conjugated ethyne, butadiyne and tetraethynylethene (trans-substituted units to a cross-conjugated tetraethynylethene unit, placed in either acyclic or cyclic arrangements. The cyclic structures correspond to so-called radiaannulenes having both endo- and exocyclic double bonds. Interactions between two redox-active TTF units in these molecules were investigated by cyclic voltammetry, UV–vis–NIR and EPR absorption spectroscopical methods of the electrochemically generated oxidized species. The electron-accepting properties of the acetylenic cores were also investigated electrochemically.

Evaluation of cyclic flexural fatigue of M-wire nickel-titanium rotary instruments.

Science.gov (United States)

Al-Hadlaq, Solaiman M S; Aljarbou, Fahad A; AlThumairy, Riyadh I

2010-02-01

This study was conducted to investigate cyclic flexural fatigue resistance of GT series X rotary files made from the newly developed M-wire nickel-titanium alloy compared with GT and Profile nickel-titanium files made from a conventional nickel-titanium alloy. Fifteen files, size 30/0.04, of each type were used to evaluate the cyclic flexural fatigue resistance. A simple device was specifically constructed to measure the time each file type required to fail under cyclic flexural fatigue testing. The results of this experiment indicated that the GT series X files had superior cyclic flexural fatigue resistance than the other 2 file types made from a conventional nickel-titanium alloy (P = .004). On the other hand, the difference between the Profile and the GT files was not statistically significant. The findings of this study suggest that size 30/0.04 nickel-titanium rotary files made from the newly developed M-wire alloy have better cyclic flexural fatigue resistance than files of similar design and size made from the conventional nickel-titanium alloy. Copyright 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Behavior of diatomaceous soil in lacustrine deposits of Bogotá, Colombia

Directory of Open Access Journals (Sweden)

Bernardo Caicedo

2018-04-01

Full Text Available This work presents a study on the behaviors of diatomaceous soils. Although studies are rarely reported on these soils, they have been identified in Mexico City, the Sea of Japan, the northeast coast of Australia, the equatorial Pacific, and the lacustrine deposit of Bogotá (Colombia, among other locations. Features of this kind of soil include high friction angle, high initial void ratio, high compressibility index, high liquid limit, and low density. Some of these features are counterintuitive from a classical soil mechanics viewpoint. To understand the geotechnical properties of the diatomaceous soil, a comprehensive experimental plan consisting of more than 2400 tests was performed, including physical tests such as grain size distribution, Atterberg limits, density of solid particles, and organic matter content; and mechanical tests such as oedometric compression tests, unconfined compression tests, and triaxial tests. Laboratory tests were complemented with scanning electron microscope (SEM observations to evaluate the microstructure of the soil. The test results show that there is an increase in liquid limit with increasing diatomaceous content, and the friction angle also increases with increasing diatomaceous content. In addition, several practical correlations were proposed for this soil type for shear strength mobilization and intrinsic compression line. Finally, useful correlations were presented, such as the relationship between the state consistency and the undrained shear strength, the friction angle and the liquid limit, the void ratio at 100 kPa and the liquid limit, the plasticity index and the diatomaceous content, among others. Keywords: Diatomaceous soil, Soft soils, Compressibility, Friction angle, Natural soil

Hydrothermal alteration and diagenesis of terrestrial lacustrine pillow basalts: Coordination of hyperspectral imaging with laboratory measurements

Science.gov (United States)

Greenberger, Rebecca N.; Mustard, John F.; Cloutis, Edward A.; Mann, Paul; Wilson, Janette H.; Flemming, Roberta L.; Robertson, Kevin M.; Salvatore, Mark R.; Edwards, Christopher S.

2015-12-01

We investigate an outcrop of ∼187 Ma lacustrine pillow basalts of the Talcott Formation exposed in Meriden, Connecticut, USA, focusing on coordinated analyses of one pillow lava to characterize the aqueous history of these basalts in the Hartford Basin. This work uses a suite of multidisciplinary measurements, including hyperspectral imaging, other spectroscopic techniques, and chemical and mineralogical analyses, from the microscopic scale up to the scale of an outcrop. The phases identified in the sample are albite, large iron oxides, and titanite throughout; calcite in vesicles; calcic clinopyroxene, aegirine, and Fe/Mg-bearing clay in the rind; and fine-grained hematite and pyroxenes in the interior. Using imaging spectroscopy, the chemistry and mineralogy results extend to the hand sample and larger outcrop. From all of the analyses, we suggest that the pillow basalts were altered initially after emplacement, either by heated lake water or magmatic fluids, at temperatures of at least 400-600 °C, and the calcic clinopyroxenes and aegirine identified in the rind are a preserved record of that alteration. As the hydrothermal system cooled to slightly lower temperatures, clays formed in the rind, and, during this alteration, the sample oxidized to form hematite in the matrix of the interior and Fe3+ in the pyroxenes in the rind. During the waning stages of the hydrothermal system, calcite precipitated in vesicles within the rind. Later, diagenetic processes albitized the sample, with albite replacing plagioclase, lining vesicles, and accreting onto the exterior of the sample. This albitization or Na-metasomatism occurred when the lake within the Hartford Basin evaporated during a drier past climatic era, resulting in Na-rich brines. As Ca-rich plagioclase altered to albite, Ca was released into solution, eventually precipitating as calcite in previously-unfilled vesicles, dominantly in the interior of the pillow. Coordinated analyses of this sample permit

Cyclic “deja vu” of real estate industry development paradigms

Directory of Open Access Journals (Sweden)

Yas’kova Natal’ya Yur’evna

2015-01-01

Full Text Available The practical projections of cyclic theories are of a great interest. Our preferences moved again from apartment houses and vertical cities to low-rise buildings. Circles set the development vector for natural, human sciences and sciences on society. The article researches the problem of cyclic development of scientific schools and their innovation ideas in the sphere of space-territory property development. The phases of the cycle were researched on the example of Bauhaus architecture school. This enables to reveal the demands and specifics of the development of new technological platforms, as well as to create the effective formats of public-private partnership. Cyclicity of business activity development under the conditions of awareness of the evolution of senses of interdisciplinary approaches utilization permits to produce the adequate development paradigm.

Effect of Surgical Removal of Endometriomas on Cyclic and Non-cyclic Pelvic Pain

Directory of Open Access Journals (Sweden)

Murat Api

2015-07-01

Full Text Available Background: Endometriosis is a complex disease with a spectrum of pain symptoms from mild dysmenorrhea to debilitating pelvic pain. There is no concrete evidence in the literature whether endometriotic cyst per se, causes pain spectrum related to the disease. The aim of the present study was to evaluate the effect of surgical removal of endometriomas on pain symptoms. Materials and Methods: In this prospective, observational, before-after study, which was conducted between March 2012 and January 2013 in Training and Research Hospital,Adana, Turkey, a total of 23 patients including 16 sexually active and 7 virgin symptomatic women were questioned for non-cyclic pelvic pain (NCPP, intensity of the NCPP, presence of cyclic dysmenorrhea, and dyspareunia before and after the endometrioma operation. Participants who were sonographically diagnosed and later pathologically confirmed as having endometrioma without sign and symptoms of deep infiltrative endometriosis (DIE were also questioned for pain symptoms before and after the laparoscopic removal of cyst wall. Patients with intraabdominal adhesions, history of pelvic inflammatory disease, and pathological diagnosis other than endometrioma were excluded. No ancillary procedures were applied for pain management, but if pain was present, pelvic peritoneal endometriotic lesions were ablated beside the removal of ovarian endometriotic cysts. Results: Out of 23 cases with endometrioma, 91 and 78% reported to have NCPP and dysmenorrhea, respectively, before the operation, while 60 and 48%, respectively, after the operation (McNemar’s test, P=0.016 for both figures. Among the sexually active cases, 31% (5/16 had dyspareunia before the operation and only 1 case reported the pain relief after the operation (McNemar’s test, P=1. Intensity of NCPP were reported to be none (8.7%, moderate (21.7%, severe (56.5% and unbearable (13% before the operation and decreased to none (43.5%, mild (43.5%, moderate (4

Occurrence of cyclic imines in European commercial seafood and consumers risk assessment

DEFF Research Database (Denmark)

Rambla-Alegre, Maria; Miles, Christopher O.; de la Iglesia, Pablo

2018-01-01

Cyclic imines constitute a quite recently discovered group of marine biotoxins that act on neural receptors and that bioaccumulate in seafood. They are grouped together due to the imino group functioning as their common pharmacore, responsible for acute neurotoxicity in mice. Cyclic imines (CIs...... countries (Italy, Portugal, Slovenia, Spain, Ireland, Norway, The Netherlands and Denmark) were obtained over 2 years. Emerging cyclic imine concentrations in all the samples were analysed on a LC-3200QTRAP and LC-HRMS QExactive mass spectrometer. In shellfish, two CIs, pinnatoxin G (PnTX-G) and 13...

Catalytic carbene transfer allows the direct customization of cyclic purine dinucleotides.

Science.gov (United States)

Fei, Na; Häussinger, Daniel; Blümli, Seraina; Laventie, Benoît-Joseph; Bizzini, Lorenzo D; Zimmermann, Kaspar; Jenal, Urs; Gillingham, Dennis

2014-08-11

We describe a simple method for the direct modification of nucleobases in cyclic purine dinucleotides, important signalling molecules in both prokaryotes and eukaryotes. The method tolerates all members of the cyclic dinucleotide family and could be used to modulate their function or introduce useful side-chains such as fluorophores and photo-crosslinking groups.

Evidences of melting of terrestrial sediments and paleoenvironment changes during the Younger Dryas in tectonic lacustrine basins of Transmexican Volcanic Belt, Mexico.

Science.gov (United States)

Israde-Alcantara, I.

2017-12-01

It is well known in the sedimentary record of several parts of the world that during the Younger Dryas interval (YD) ocurred an abrupt environmental change between 12,900 and 11,700 cal yr BP (10,900 to 10,000 14C BP). In the lacustrine basins this changes are often preserved and in some Mexican lakes this is a distinctive stratigraphic marker for the YD. We analized the proxies of this event in cores of two lakes (Chapala, Cuitzeo) and three trenches of ex-lakes (Acambay,Texcoco and El Cedral). Deposits consist of fine detrital material with often Pleistocene fossil vertebrate assemblages. At the Chapala, Cuitzeo, Acambay, and Tocuila lacustrine environments are found in association with a distinctive dark organic layer showing sharp changes in the diatom, pollen, mineralogical and geochemical record. Includes also microscopic magnetic, Fe-rich spherules, silica melted droplets with aerodynamic shapes (tektites), followed by large amounts of charcoal, and sometimes nanodiamonds (Cuitzeo), that were deposited at the onset of the YD or in the limit Pleistocene-Holocene. These unusual materials are buried more than 2.50 meters and were not observed above or below the Younger Dryas sediments at these sites. The geochemistry of the microspherules indicates that they are not volcanic, anthropogenic or authigenic origin. A very distinctive feature is the shape of the spherules, ovoid, polygonal, filigreed or dendritic indicating melting and quenching infering that are product of an impact event. Their morphologies includes hollow shells caused by de-gassing of elements at very high temperatures causing a flattened side with a "skirt" structure by a high-velocity collision.Our results are consistent with the Firestone hypothesis.

[Asthma and cyclic neutropenia].

Science.gov (United States)

Salazar Cabrera, A N; Berrón Pérez, R; Ortega Martell, J A; Onuma Takane, E

1996-01-01

We report a male with history of recurrent infections (recurrent oral aphtous disease [ROAD], middle ear infections and pharyngo amigdalitis) every 3 weeks since he was 7 months old. At the age of 3 years cyclic neutropenia was diagnosed with cyclic fall in the total neutrophil count in blood smear every 21 days and prophylactic antimicrobial therapy was indicated. Episodic events every 3 weeks of acute asthma and allergic rhinitis were detected at the age of 6 years old and specific immunotherapy to Bermuda grass was given during 3 years with markedly improvement in his allergic condition but not in the ROAD. He came back until the age of 16 with episodic acute asthma and ROAD. The total neutrophil count failed to 0 every 21 days and surprisingly the total eosinophil count increased up to 2,000 at the same time, with elevation of serum IgE (412 Ul/mL). Specific immunotherapy to D.pt. and Aller.a. and therapy with timomodulin was indicated. After 3 months we observed clinical improvement in the asthmatic condition and the ROAD disappeared, but the total neutrophil count did not improve. We present this case as a rare association between 2 diseases with probably no etiological relationship but may be physiopatological that could help to understand more the pathogenesis of asthma.

Plasma-focused cyclic accelerators

International Nuclear Information System (INIS)

Mondelli, A.A.; Chernin, D.P.

1985-01-01

The use of ambient plasma to neutralize the transverse forces of an intense particle beam has been known for many years. Most recently, the so-called ion-focused regime (IFR) for beam propagation has been used as a means of focusing intense electron beams in linear accelerators and suggested for injecting an electron beam across magnetic field lines into a high-current cyclic accelerator. One technique for generating the required background plasma for IFR propagation is to use a laser to ionize ambient gas in the accelerator chamber. For cyclic accelerators a technique is required for carrying the plasma channel and the beam around a bend. Multiple laser-generated channels with dipole magnetic fields to switch the beam from one channel to the next have been tested at Sandia. This paper discusses an alternative means of plasma production for IFR, viz. by using rf breakdown. For this approach the accelerator chamber acts as a waveguide. With a suitable driving frequency, a waveguide mode can be driven which has its peak field intensity on the axis with negligible fields at the chamber walls. The plasma production and hence the beam propagation is thereby isolated from the walls. This technique is not limited to toroidal accelerators. It may be applied to any accelerator or recirculator geometry as well as for beam steering and for injection or extraction of beams in closed accelerator configurations

Simulation of cyclic stress-strain relation under non proportional loading

International Nuclear Information System (INIS)

Chen, X.; Zhu, Q.X.; Abel, A.

1995-01-01

A series of cyclic constitutive experiments have been conducted on 42 Cr Mo steel on MTS809 machine under tension-torsional loading. Thin-walled tube specimen were used. Two kinds of cruciform strain path have been investigated. The paper suggests a simple method for the calculation of stable cyclic stress and strain values based on a modified endochronic constitutive theory by redefined intrinsic time scale. (author). 6 refs., 3 figs

Geometric phases for mixed states during cyclic evolutions

International Nuclear Information System (INIS)

Fu Libin; Chen Jingling

2004-01-01

The geometric phases of cyclic evolutions for mixed states are discussed in the framework of unitary evolution. A canonical 1-form is defined whose line integral gives the geometric phase, which is gauge invariant. It reduces to the Aharonov and Anandan phase in the pure state case. Our definition is consistent with the phase shift in the proposed experiment (Sjoeqvist et al 2000 Phys. Rev. Lett. 85 2845) for a cyclic evolution if the unitary transformation satisfies the parallel transport condition. A comprehensive geometric interpretation is also given. It shows that the geometric phases for mixed states share the same geometric sense with the pure states

Gold prices: Analyzing its cyclical behavior

Directory of Open Access Journals (Sweden)

Martha Gutiérrez

2013-07-01

Full Text Available Gold is a commodity that is seen as a safe haven when a financial crisis strikes, but when stock markets are prosperous, these are more attractive investment alternatives, and so the gold cycle goes on and on. The DJIA/GF (Dow Jones Industrial Average and Gold Fix ratio is chosen to establish the evolution of gold prices in relation to the NYSE. This paper has two goals: to prove that the DJIA/GF ratio is strongly cyclical by using Fourier analysis and to set a predictive neural networks model to forecast the behavior of this ratio during 2011-2020. To this end, business cycle events like the Great Depression along with the 1970s crisis, and the 1950s boom along with the world economic recovery of the 1990s are contrasted in light of the mentioned ratio. Gold prices are found to evolve cyclically with a dominant period of 37 years and are mainly affected by energy prices, financial markets and macroeconomic indicators.

Cosmic evolution in a cyclic universe

International Nuclear Information System (INIS)

Steinhardt, Paul J.; Turok, Neil

2002-01-01

Based on concepts drawn from the ekpyrotic scenario and M theory, we elaborate our recent proposal of a cyclic model of the universe. In this model, the universe undergoes an endless sequence of cosmic epochs which begin with the universe expanding from a 'big bang' and end with the universe contracting to a 'big crunch'. Matching from 'big crunch' to 'big bang' is performed according to the prescription recently proposed with Khoury, Ovrut and Seiberg. The expansion part of the cycle includes a period of radiation and matter domination followed by an extended period of cosmic acceleration at low energies. The cosmic acceleration is crucial in establishing the flat and vacuous initial conditions required for ekpyrosis and for removing the entropy, black holes, and other debris produced in the preceding cycle. By restoring the universe to the same vacuum state before each big crunch, the acceleration ensures that the cycle can repeat and that the cyclic solution is an attractor

Cyclic voltammograms for H on Pt(111) and Pt(100) from first principles

DEFF Research Database (Denmark)

Karlberg, Gustav; Jaramillo, Thomas; Skulason, Egill

2007-01-01

Cyclic voltammetry is a fundamental experimental method for characterizing electrochemical surfaces. Despite its wide use, a way to quantitatively and directly relate cyclic voltammetry to ab initio calculations has been lacking. We derive the cyclic voltammogram for H on Pt(111) and Pt(100), bas...... solely on density functional theory calculations and standard molecular tables. By relating the gas phase adsorption energy to the electrochemical electrode potential, we provide a direct link between surface science and electrochemistry....

Empirical approach based on centrifuge testing for cyclic deformations of laterally loaded piles in sand

DEFF Research Database (Denmark)

Truong, P.; Lehane, B. M.; Zania, Varvara

2018-01-01

A systematic study into the response of monopiles to lateral cyclic loading in medium dense and dense sand was performed in beam and drum centrifuge tests. The centrifuge tests were carried out at different cyclic load and magnitude ratios, while the cyclic load sequence was also varied...

A cyclically actuated electrolytic drug delivery device

KAUST Repository

Yi, Ying; Buttner, Ulrich; Foulds, Ian G.

2015-01-01

This work, focusing on an implantable drug delivery system, presents the first prototype electrolytic pump that combines a catalytic reformer and a cyclically actuated mode. These features improve the release performance and extend the lifetime

The Chemistry of Cyclic All-Nitrogen Molecules

National Research Council Canada - National Science Library

Wodtke, Alec M

2006-01-01

..., $474,927, February 15, 2004 - December 31, 2006. During this period, we have extended our preliminary investigations of azide photochemistry, with the aim of demonstrating unambiguously the photochemical production of cyclic-N, and of revealing...

Cyclic Plastic Deformation and Welding Simulation

NARCIS (Netherlands)

Ten Horn, C.H.L.J.

2003-01-01

One of the concerns of a fitness for purpose analysis is the quantification of the relevant material properties. It is known from experiments that the mechanical properties of a material can change due to a monotonic plastic deformation or a cyclic plastic deformation. For a fitness for purpose

The rearrangements of naphthylnitrenes: UV/Vis and IR spectra of azirines, cyclic ketenimines, and cyclic nitrile ylides.

Science.gov (United States)

Maltsev, Alexander; Bally, Thomas; Tsao, Meng-Lin; Platz, Matthew S; Kuhn, Arvid; Vosswinkel, Michael; Wentrup, Curt

2004-01-14

Ar matrix photolysis of 1- and 2-naphthyl azides 3 and 4 at 313 nm initially affords the singlet naphthyl nitrenes, (1)()1 and (1)()2. Relaxation to the corresponding lower energy, persistent triplet nitrenes (3)()1 and (3)()2 competes with cyclization to the azirines 15 and 18, which can also be formed photochemically from the triplet nitrenes. On prolonged irradiation, the azirines can be converted to the seven-membered cyclic ketenimines 10 and 13, respectively, as described earlier by Dunkin and Thomson. However, instead of the o-quinoid ketenimines 16 and 19, which are the expected primary ring-opening products of azirines 15 and 18, respectively, we observed their novel bond-shift isomers 17 and 20, which may be formally regarded as cyclic nitrile ylides. The existence of such ylidic heterocumulenes has been predicted previously, but this work provides the first experimental observation of such species. The factors which are responsible for the special stability of the ylidic species 17 and 20 are discussed.

Comparative assessment of cyclic J-R curve determination by different methods in a pressure vessel steel

Energy Technology Data Exchange (ETDEWEB)

Chowdhury, Tamshuk, E-mail: tamshuk@gmail.com [Deep Sea Technologies, National Institute of Ocean Technology, Chennai, 600100 (India); Sivaprasad, S.; Bar, H.N.; Tarafder, S. [Fatigue & Fracture Group, Materials Science and Technology Division, CSIR-National Metallurgical Laboratory, Jamshedpur, 831007 (India); Bandyopadhyay, N.R. [School of Materials Science and Engineering, Indian Institute of Engineering, Science and Technology, Shibpur, Howrah, 711103 (India)

2016-04-15

Cyclic J-R behaviour of a reactor pressure vessel steel using different methods available in literature has been examined to identify the best suitable method for cyclic fracture problems. Crack opening point was determined by moving average method. The η factor was experimentally determined for cyclic loading conditions and found to be similar to that of ASTM value. Analyses showed that adopting a procedure analogous to the ASTM standard for monotonic fracture is reasonable for cyclic fracture problems, and makes the comparison to monotonic fracture results straightforward. - Highlights: • Different methods of cyclic J-R evaluation compared. • A moving average method for closure point proposed. • η factor for cyclic J experimentally validated. • Method 1 is easier, provides a lower bound and direct comparison to monotonic fracture.

The influence of cyclic loading on gentamicin release from acrylic bone cements

NARCIS (Netherlands)

Hendriks, JGE; Neut, D; Hazenberg, JG; Verkerke, GJ; van Horn, [No Value; van der Mei, HC; Busscher, HJ

Antibiotic-loaded acrylic bone cement is widely used in total joint replacement to reduce infections. Walking results in cyclic loading, which has been suggested to stimulate antibiotic release. The goal of this study is to compare antibiotic release from cyclically loaded bone cement with the

Cyclic etching of tin-doped indium oxide using hydrogen-induced modified layer

Science.gov (United States)

Hirata, Akiko; Fukasawa, Masanaga; Nagahata, Kazunori; Li, Hu; Karahashi, Kazuhiro; Hamaguchi, Satoshi; Tatsumi, Tetsuya

2018-06-01

The rate of etching of tin-doped indium oxide (ITO) and the effects of a hydrogen-induced modified layer on cyclic, multistep thin-layer etching were investigated. It was found that ITO cyclic etching is possible by precisely controlling the hydrogen-induced modified layer. Highly selective etching of ITO/SiO2 was also investigated, and it was suggested that cyclic etching by selective surface adsorption of Si can precisely control the etch rates of ITO and SiO2, resulting in an almost infinite selectivity for ITO over SiO2 and in improved profile controllability.

'In-vivo' measurement of selenium in liver using a cyclic activation method

Energy Technology Data Exchange (ETDEWEB)

Nicolaou, G E; Spyrou, N M [Surrey Univ., Guildford (UK). Dept. of Physics; Matthews, I P [UKAEA Atomic Energy Research Establishment, Harwell. Environmental and Medical Sciences Div.; Stephens-Newsham, L G [Alberta Univ., Edmonton (Canada)

1982-01-01

In-vivo cyclic neutron activation analysis was used to measure selenium concentrations in liver by means of sup(77m)Se (17.6 s). The cyclic activation facility incorporates an oscillating 5 Ci Am/Be neutron source while the 'patient' remains stationary during the examination. For a total experimental time of 1800 s and cyclic period of 26 s, a minimum detection limit of 0.6 ppm may be obtained, however, when comparison is made with in-vitro results, this limit may be significantly lower. The dose for such an investigation was approximately equal to 0.26x10/sup -2/ Sv.

Analysis of the kinetics of decohesion process in the conditions of cyclic temperature variations

International Nuclear Information System (INIS)

Zuchowski, R.

1981-01-01

Specimens made of four types of heat-resistant steels were used in the investigation. Various variants of loading process were applied, resulting in thermal fatigue, cyclic creep and isothermal fatigue. Stress or strain variation as well as intensity of acoustic emission were recorded during the tests as a function of time. Cyclic variations of strain or stress amplitude were found to occur one full period covering few to several cycles. Comparing the relative number of acoustic emission impulses with the variation of stress or strain leads to the conclusion that cyclic character of strain or stress variation results from cyclic character of damage cumulation process. This statement is confirmed by the results of material damage degree determination based on specific strain work measurements. Results of investigation testify to the equivalence of action (in terms of energy) of cyclically variable force field at constant temperature and of constant force field in the conditions of cyclic temperature variations. Damage mechanism can be different in each case, because it depends (for a given material) on loading process parameters and in particular - on temperature and stress value. (orig./HP)

Creep crack growth by grain boundary cavitation under monotonic and cyclic loading

Science.gov (United States)

Wen, Jian-Feng; Srivastava, Ankit; Benzerga, Amine; Tu, Shan-Tung; Needleman, Alan

2017-11-01

Plane strain finite deformation finite element calculations of mode I crack growth under small scale creep conditions are carried out. Attention is confined to isothermal conditions and two time histories of the applied stress intensity factor: (i) a monononic increase to a plateau value subsequently held fixed; and (ii) a cyclic time variation. The crack growth calculations are based on a micromechanics constitutive relation that couples creep deformation and damage due to grain boundary cavitation. Grain boundary cavitation, with cavity growth due to both creep and diffusion, is taken as the sole failure mechanism contributing to crack growth. The influence on the crack growth rate of loading history parameters, such as the magnitude of the applied stress intensity factor, the ratio of the applied minimum to maximum stress intensity factors, the loading rate, the hold time and the cyclic loading frequency, are explored. The crack growth rate under cyclic loading conditions is found to be greater than under monotonic creep loading with the plateau applied stress intensity factor equal to its maximum value under cyclic loading conditions. Several features of the crack growth behavior observed in creep-fatigue tests naturally emerge, for example, a Paris law type relation is obtained for cyclic loading.

Kenaf Fibre Reinforced Polypropylene Composites: Effect of Cyclic Immersion on Tensile Properties

Directory of Open Access Journals (Sweden)

W. H. Haniffah

2015-01-01

Full Text Available This research studied the degradation of tensile properties of kenaf fibre reinforced polypropylene composites due to cyclic immersion into two different solutions, as well as comparison of the developed composites’ tensile properties under continuous and cyclic immersion. Composites with 40% and 60% fibre loadings were immersed in tap water and bleach for 4 cycles. Each cycle consisted of 3 days of immersion and 4 days of conditioning in room temperature (28°C and 55% humidity. The tensile strength and modulus of composites were affected by fibre composition, type of liquid of immersion, and number of cycles. The number of immersion cycles and conditioning caused degradation to tensile strength and modulus of kenaf fibre reinforced polypropylene composites. Continuous and cyclic immersion in bleach caused tensile strength of the composites to differ significantly whereas, for tensile modulus, the difference was insignificant in any immersion and fibre loadings. However, continuous immersion in the bleach reduced the tensile strength of composites more compared to cyclic immersion. These preliminary results suggest further evaluation of the suitability of kenaf fibre reinforced polypropylene composites for potential bathroom application where the composites will be exposed to water/liquid in cyclic manner due to discontinuous usage of bathroom.

Experimental Investigation on Deformation Failure Characteristics of Crystalline Marble Under Triaxial Cyclic Loading

Science.gov (United States)

Yang, Sheng-Qi; Tian, Wen-Ling; Ranjith, P. G.

2017-11-01

The deformation failure characteristics of marble subjected to triaxial cyclic loading are significant when evaluating the stability and safety of deep excavation damage zones. To date, however, there have been notably few triaxial experimental studies on marble under triaxial cyclic loading. Therefore, in this research, a series of triaxial cyclic tests was conducted to analyze the mechanical damage characteristics of a marble. The post-peak deformation of the marble changed gradually from strain softening to strain hardening as the confining pressure increased from 0 to 10 MPa. Under uniaxial compression, marble specimens showed brittle failure characteristics with a number axial splitting tensile cracks; in the range of σ 3 = 2.5-7.5 MPa, the marble specimens assumed single shear fracture characteristics with larger fracture angles of about 65°. However, at σ 3 = 10 MPa, the marble specimens showed no obvious shear fracture surfaces. The triaxial cyclic experimental results indicate that in the range of the tested confining pressures, the triaxial strengths of the marble specimens under cyclic loading were approximately equal to those under monotonic loading. With the increase in cycle number, the elastic strains of the marble specimens all increased at first and later decreased, achieving maximum values, but the plastic strains of the marble specimens increased nonlinearly. To evaluate quantitatively the damage extent of the marble under triaxial cyclic loading, a damage variable is defined according to the irreversible deformation for each cycle. The evolutions of the elastic modulus for the marble were characterized by four stages: material strengthening, material degradation, material failure and structure slippage. Based on the experimental results of the marble specimens under complex cyclic loading, the cohesion of the marble decreased linearly, but the internal friction angles did not depend on the damage extent. To describe the peak strength

Cloning, Sequencing, and Expression of the Gene Encoding Cyclic 2,3-Diphosphoglycerate Synthetase, the Key Enzyme of Cyclic 2,3-Diphosphoglycerate Metabolism in Methanothermus fervidus

OpenAIRE

Matussek, Karl; Moritz, Patrick; Brunner, Nina; Eckerskorn, Christoph; Hensel, Reinhard

1998-01-01

Cyclic 2,3-diphosphoglycerate synthetase (cDPGS) catalyzes the synthesis of cyclic 2,3-diphosphoglycerate (cDPG) by formation of an intramolecular phosphoanhydride bond in 2,3-diphosphoglycerate. cDPG is known to be accumulated to high intracellular concentrations (>300 mM) as a putative thermoadapter in some hyperthermophilic methanogens. For the first time, we have purified active cDPGS from a methanogen, the hyperthermophilic archaeon Methanothermus fervidus, sequenced the coding gene, and...

Cyclical Variability of Prominences, CMEs and Flares

Indian Academy of Sciences (India)

tribpo

For many years, qualitative studies were made about the cyclical ... plan to review the more recent research concerning all these topics. Key words. ... are distributed in three narrow zones, which show different types of time-latitude behaviour.

Small-Scale Testing of Cyclic Laterally Loaded Monopiles in Dense Saturated Sand

DEFF Research Database (Denmark)

Nicolai, Giulio; Ibsen, Lars Bo

2014-01-01

Monopiles are currently the most common foundations for offshore wind turbines, which are subjected to millions of cyclic loads that are still not well interpreted in the design guidelines. The accumulated rotation of the turbine and the change of foundation stiffness due to the long-term cyclic ...

Well-Defined Cyclic Triblock Terpolymers: A Missing Piece of the Morphology Puzzle

KAUST Repository

Polymeropoulos, George

2016-10-27

Two well-defined cyclic triblock terpolymers, missing pieces of the terpolymer morphology puzzle, consisting of poly(isoprene), polystyrene, and poly(2-vinylpyridine), were synthesized by combining the Glaser coupling reaction with anionic polymerization. An α,ω-dihydroxy linear triblock terpolymer (OH-PI1,4-b-PS-b-P2VP-OH) was first synthesized followed by transformation of the OH to alkyne groups by esterification with pentynoic acid and cyclization by Glaser coupling. The size exclusion chromatography (SEC) trace of the linear terpolymer precursor was shifted to lower elution time after cyclization, indicating the successful synthesis of the cyclic terpolymer. Additionally, the SEC trace of the cyclic terpolymer produced, after cleavage of the ester groups, shifted again practically to the position corresponding to the linear precursor. The first exploratory results on morphology showed the tremendous influence of the cyclic structure on the morphology of terpolymers. © 2016 American Chemical Society.

Comparison of cyclic fatigue resistance of original and counterfeit rotary instruments.

Science.gov (United States)

Ertas, Huseyin; Capar, Ismail Davut; Arslan, Hakan; Akan, Ender

2014-05-31

In recent years, with the advances in counterfeiting methods, counterfeit products have reached the dental market. The purpose of this study was to compare the cyclic fatigue resistance of original and counterfeit rotary root canal instruments. The cyclic fatigue of original and counterfeit ProTaper F2 endodontic instruments was tested (n = 20) in 3 mm radius steel canals with a 60° angle of curvature. The number of cycles to fracture (NCF) was calculated, and the data were subjected to the Student's t-test (α = 0.05). The original instruments showed better cyclic fatigue resistance than the counterfeit ones (p instruments was very low. As a result, clinicians should be careful not to purchase counterfeit products.

Phantom energy accretion onto black holes in a cyclic universe

International Nuclear Information System (INIS)

Sun Chengyi

2008-01-01

Black holes pose a serious problem in cyclic or oscillating cosmology. It is speculated that, in the cyclic universe with phantom turnarounds, black holes will be torn apart by phantom energy prior to turnaround before they can create any problems. In this paper, using the mechanism of phantom accretion onto black holes, we find that black holes do not disappear before phantom turnaround. But the remanent black holes will not cause any problems due to Hawking evaporation.

Cyclic adenosine 3:5-monophosphate binding proteins in Hartmannella culbertsoni

International Nuclear Information System (INIS)

Verma, A.K.; Krishna Murti, C.R.

1976-01-01

When 100, 000 g supernatant fractions of homogenates of Hartmannella culbertsoni were incubated with ('- 3 H)-cyclic adenosine 3 : 5 monophosphate and passed through a sephadex G-100 column, radioactivity appeared with protein fractions eluted after the void colume. About 75% radioactivity bound to these fractions was recovered as cyclic adenosine 3 : 5 monophosphate. Unlabelled cAMP diluted the amount of radioactivity bound. Adenosine, deoxyadenosine, 5-AMP, 3-AMP, ADP and ATP did not inhibit binding. (author)

Laboratory Test Setup for Cyclic Axially Loaded Piles in Sand

DEFF Research Database (Denmark)

Thomassen, Kristina; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

2017-01-01

This paper presents a comprehensive description and the considerations regarding the design of a new laboratory test setup for testing cyclic axially loaded piles in sand. The test setup aims at analysing the effect of axial one-way cyclic loading on pile capacity and accumulated displacements....... Another aim was to test a large diameter pile segment with dimensions resembling full-scale piles to model the interface properties between pile and sand correctly. The pile segment was an open-ended steel pipe pile with a diameter of 0.5 m and a length of 1 m. The sand conditions resembled the dense sand...... determined from the API RP 2GEO standard and from the test results indicated over consolidation of the sand. Two initial one-way cyclic loading tests provided results of effects on pile capacity and accumulated displacements in agreement with other researchers’ test results....

The cyclical monitoring system for digital power supplies at SSRF

International Nuclear Information System (INIS)

Tang Junlong; Li Deming; Shen Tianjian

2009-01-01

Based on available digital PS testing system and long-distance monitoring hardwares, the cyclical monitoring system for digital power supplies (PS) was developed at SSRF. Two models, i.e.long-distance cyclical monitoring and local cyclical monitoring, were established. The software developed in LabVIEW language was applied to the two models without any user interface modification. The user interface is simple. The system is suitable for debugging the digital PSs during long-distance monitoring and examining the performance. The long-distance model imitates the digital PSs' status for fault analysis and communication between the digital PS and the centre control room. The local model simultaneously examines stability of 18 new PSs for 24 h, monitors the PS controller, and detects malfunction. Parameters and status of the controller can be stored in Excel or Text file. The two models have been used at SSRF for monitoring the digital PSs. (authors)

Cyclic polyalcohols: fingerprints to identify the botanical origin of natural woods used in wine aging.

Science.gov (United States)

Alañón, M Elena; Díaz-Maroto, M Consuelo; Díaz-Maroto, Ignacio J; Vila-Lameiro, Pablo; Pérez-Coello, M Soledad

2011-02-23

Cyclic polyalcohol composition of 80 natural wood samples from different botanical species, with the majority of them used in the oenology industry for aging purposes, has been studied by gas chromatography-mass spectrometry (GC-MS) after its conversion into their trimethylsilyloxime derivatives. Each botanical species showed a different and specific cyclic polyalcohol profile. Oak wood samples were characterized by the richness in deoxyinositols, especially proto-quercitol. Meanwhile, other botanical species showed a very low content of cyclic polyalcohols. The qualitative and quantitative study of cyclic polyalcohols was a useful tool to characterize and differentiate woods of different botanical origin to guarantee the authenticity of chips used in the wine-aging process. Monosaccharide composition was also analyzed, showing some quantitative differences among species, but cyclic polyalcohols were the compounds that revealed the main differentiation power.

Cyclic Polymers: From Scientific Curiosity to Advanced Materials for Gene Delivery and Surface Modification.

Science.gov (United States)

Verbraeken, Bart; Hoogenboom, Richard

2017-06-12

Cyclic versus linear: The superiority of cyclic polymers over their linear counterparts is highlighted. Cyclic poly(2-oxazoline)s have been shown to provide excellent shielding properties when grafted to TiO 2 surfaces and Fe 3 O 4 nanoparticles owing to their ultrahigh grafting densities leading to low friction surfaces, superior antifouling properties, and extreme nanoparticle stabilization. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fracture studies on stainless steel straight pipes under earthquake-type cyclic loading

International Nuclear Information System (INIS)

Raghava, G.; Vishnuvardhan, S.; Gandhi, P.; Vaze, K.K.

2014-01-01

In order to study the crack growth and cyclic fracture behaviour, which are required for realistic assessment of Leak Before Break (LBB) applicability, experimental investigations were carried out on straight pipes under quasi-crystal loading. Totally 13 pipes were tested; three were stainless steel welded (SSW) using conventional shielded metal arc welding (SMAW) technique and the remaining specimens were Narrow Gap Welded (NGW). The fracture tests were carried out under load control, displacement control and combination of the two; the pipes were subjected to different amplitudes of load or load-line displacement (LLD), which were decided based on the response of the pipes under monotonic loading. Cyclic tearing and crack growth studies on eight straight pipes of the same material reported earlier in published literature are also considered for studying the results and understanding the behaviour. Under load control, with almost equal load amplitude, the NGW pipe exhibited improved life in comparison with SMAW pipe when both are subjected to cyclic loading. The crack growth and tearing instability behaviour of the pipes were studied. The same were found to be different for load control, displacement control and combined control tests. Based in the load-controlled experimental results, material specific plot between cyclic load amplitude (as a percentage of maximum load carrying capacity of a specimen under monotonic fracture) and number of cycles to failure was obtained. The results indicate that the piping components subjected to quasi-cyclic loading may fail in very less number of cycles even when the load amplitude is sufficiently below the monotonic fracture/collapse load. These studies will be helpful in designing nuclear power plant (NPP) piping components subjected to earthquake-type cyclic loading. (author)

Fluorine determination in diet samples using cyclic NAA and PIGE analysis

International Nuclear Information System (INIS)

Farooqi, A.S.; Arshed, W.; Akanle, O.A.; Spyrou, N.M.

1991-01-01

Fluorine is an important trace element for life and human well-being. Food, in general, provides about 40% of the fluorine intake in the human body. In order to measure fluorine levels in human diet samples, Instrumental Neutron Activation Analysis (INAA) and Proton Induced Gamma-Ray Emission (PIGE) analysis were used. Thermal and epithermal cyclic NAA methods were applied, employing the 19 F(n,γ) 20 F and 19 F(n,p) 19 O nuclear reactions for the determination of fluorine, respectively. Corrections were made for the sodium matrix interference caused by the 23 Na(n,α) 20 F threshold reaction in the case of thermal cyclic NAA and for the oxygen interference via 18 O(n,γ) 19 O reaction when using the epithermal cyclic NAA method. The fluorine contents of diet samples were also determined by PIGE analysis making use of the resonance reaction 19 F(p,αγ) 16 O at 872 KeV. Thermal cyclic NAA was found to be most suitable for the determination of low concentrations of fluorine in the diet samples, with a detection limit of less than 10 μg/g

Long-term cyclicities in Phanerozoic sea-level sedimentary record and their potential drivers

Science.gov (United States)

Boulila, Slah; Laskar, Jacques; Haq, Bilal U.; Galbrun, Bruno; Hara, Nathan

2018-06-01

Cyclic sedimentation has varied at several timescales and this variability has been geologically well documented at Milankovitch timescales, controlled in part by climatically (insolation) driven sea-level changes. At the longer (tens of Myr) timescales connection between astronomical parameters and sedimentation via cyclic solar-system motions within the Milky Way has also been proposed, but this hypothesis remains controversial because of the lack of long geological records. In addition, the absence of a meaningful physical mechanism that could explain the connection between climate and astronomy at these longer timescales led to the more plausible explanation of plate motions as the main driver of climate and sedimentation through changes in ocean and continent mass distribution on Earth. Here we statistically show a prominent and persistent 36 Myr sedimentary cyclicity superimposed on two megacycles ( 250 Myr) in a relatively well-constrained sea-level (SL) record of the past 542 Myr (Phanerozoic eon). We also show two other significant 9.3 and 91 Myr periodicities, but with lower amplitudes. The 9.3 Myr cyclicity was previously attributed to long-period Milankovitch band based on the Cenozoic record. However, the 91 Myr cyclicity has never been observed before in the geologic record. The 250 Myr cyclicity was attributed to the Wilson tectonic (supercontinent) cycle. The 36 Myr periodicity, also detected for the first time in SL record, has previously been ascribed either to tectonics or to astronomical cyclicity. Given the possible link between amplitudes of the 36 and 250 Myr cyclicities in SL record and the potential that these periodicities fall into the frequency band of solar system motions, we suggest an astronomical origin, and model these periodicities as originating from the path of the solar system in the Milky Way as vertical and radial periods that modulate the flux of cosmic rays on Earth. Our finding of the 36 Myr SL cyclicity lends credibility

Finite element analysis of the cyclic indentation of bilayer enamel

International Nuclear Information System (INIS)

Jia, Yunfei; Xuan, Fu-zhen; Chen, Xiaoping; Yang, Fuqian

2014-01-01

Tooth enamel is often subjected to repeated contact and often experiences contact deformation in daily life. The mechanical strength of the enamel determines the biofunctionality of the tooth. Considering the variation of the rod arrangement in outer and inner enamel, we approximate enamel as a bilayer structure and perform finite element analysis of the cyclic indentation of the bilayer structure, to mimic the repeated contact of enamel during mastication. The dynamic deformation behaviour of both the inner enamel and the bilayer enamel is examined. The material parameters of the inner and outer enamel used in the analysis are obtained by fitting the finite element results with the experimental nanoindentation results. The penetration depth per cycle at the quasi-steady state is used to describe the depth propagation speed, which exhibits a two-stage power-law dependence on the maximum indentation load and the amplitude of the cyclic load, respectively. The continuous penetration of the indenter reflects the propagation of the plastic zone during cyclic indentation, which is related to the energy dissipation. The outer enamel serves as a protective layer due to its great resistance to contact deformation in comparison to the inner enamel. The larger equivalent plastic strain and lower stresses in the inner enamel during cyclic indentation, as calculated from the finite element analysis, indicate better crack/fracture resistance of the inner enamel. (paper)

Finite element analysis of the cyclic indentation of bilayer enamel

Science.gov (United States)

Jia, Yunfei; Xuan, Fu-zhen; Chen, Xiaoping; Yang, Fuqian

2014-04-01

Tooth enamel is often subjected to repeated contact and often experiences contact deformation in daily life. The mechanical strength of the enamel determines the biofunctionality of the tooth. Considering the variation of the rod arrangement in outer and inner enamel, we approximate enamel as a bilayer structure and perform finite element analysis of the cyclic indentation of the bilayer structure, to mimic the repeated contact of enamel during mastication. The dynamic deformation behaviour of both the inner enamel and the bilayer enamel is examined. The material parameters of the inner and outer enamel used in the analysis are obtained by fitting the finite element results with the experimental nanoindentation results. The penetration depth per cycle at the quasi-steady state is used to describe the depth propagation speed, which exhibits a two-stage power-law dependence on the maximum indentation load and the amplitude of the cyclic load, respectively. The continuous penetration of the indenter reflects the propagation of the plastic zone during cyclic indentation, which is related to the energy dissipation. The outer enamel serves as a protective layer due to its great resistance to contact deformation in comparison to the inner enamel. The larger equivalent plastic strain and lower stresses in the inner enamel during cyclic indentation, as calculated from the finite element analysis, indicate better crack/fracture resistance of the inner enamel.

Solving cyclical nurse scheduling problem using preemptive goal programming

Science.gov (United States)

Sundari, V. E.; Mardiyati, S.

2017-07-01

Nurse scheduling system in a hospital is being modeled as a preemptive goal programming problem that is solved by using LINGO software with the objective function to minimize deviation variable at each goal. The scheduling is done cyclically, so every nurse is treated fairly since they have the same work shift portion with the other nurses. By paying attention to the hospital's rules regarding nursing work shift cyclically, it can be obtained that numbers of nurse needed in every ward are 18 nurses and the numbers of scheduling periods are 18 periods where every period consists of 21 days.

Effect of cyclic loading on the viscoplastic behaviour of Zircaloy 4 cladding tubes

International Nuclear Information System (INIS)

Bouffioux, P.; Gabriel, B.; Soniak, A.; Mardon, J.P.

1995-06-01

Most of the electricity being generated by nuclear energy load follow and remote control have become normal operating modes in the French PWR. In addition, EDF is developing a strategy of fuel sub-assembly burnup extension. Those operating conditions will lead to cyclic straining of the Zircaloy cladding tube which could induce damages. Therefore, EDF, CEA, and FRAMATOME has started a joint R and D cooperative program in order to investigate the mechanical behaviour of Zircaloy cladding tubes under cyclic loading. This paper is dealing with the effect of a pre-cyclic loading on the plasticity properties of Zircaloy 4 cladding tubes. Load controlled cyclic tests were carried out at 350 deg. C and 0.5 Hz in both axial and hoop directions. The Woehler curves were determined. Sequential tests combining pre-cyclic loading to 50 and 75 % fraction life with tension were then performed. It has ben noticed that the pre-cycling loading does not change the plastic flow curve of the Zircaloy 4 cladding tubes and therefore does not induce observable macroscopic damage. It has been concluded that a linear cumulative damage rule like ΣΔN(σ)/N r(σ) is very conservative. (author)

Anodic selective functionalization of cyclic amine derivatives

OpenAIRE

Onomura, Osamu

2012-01-01

Anodic reactions are desirable methods from the viewpoint of Green Chemistry, since no toxic oxidants are necessary for the oxidation of organic molecules. This review introduces usefulness of anodic oxidation and successive reaction for selective functionalization of cyclic amine derivatives.

Binding of the cyclic AMP receptor protein of Escherichia coli to RNA polymerase.

Science.gov (United States)

Pinkney, M; Hoggett, J G

1988-03-15

Fluorescence polarization studies were used to study the interaction of a fluorescein-labelled conjugate of the Escherichia coli cyclic AMP receptor protein (F-CRP) and RNA polymerase. Under conditions of physiological ionic strength, F-CRP binds to RNA polymerase holoenzyme in a cyclic AMP-dependent manner; the dissociation constant was about 3 microM in the presence of cyclic AMP and about 100 microM in its absence. Binding to core RNA polymerase under the same conditions was weak (Kdiss. approx. 80-100 microM) and independent of cyclic AMP. Competition experiments established that native CRP and F-CRP compete for the same binding site on RNA polymerase holoenzyme and that the native protein binds about 3 times more strongly than does F-CRP. Analytical ultracentrifuge studies showed that CRP binds predominantly to the monomeric rather than the dimeric form of RNA polymerase.

Nitration Study of Cyclic Ladder Polyphenylsilsesquioxane

Directory of Open Access Journals (Sweden)

LIANG Jia-xiang

2017-05-01

Full Text Available Several nitration reagents including fuming nitric acid, HNO3-H2SO4, KNO3-H2SO4, HNO3-KNO3, CH3COOH-KNO3, (CH3CO2O-HNO3 were used to nitrate cyclic ladder polyphenylsilsesquioxane (CL-PPSQ in different conditions in order to enhance the compatibility of the CL-PPSQ in polymers, the NO2-PPSQ was obtained. FTIR, element analysis, GPC, TGA and 1H NMR were used to characterize the structures of the nitrated products. The results show that the nitrating abilities of the fuming nitric acid, HNO3-H2SO4 and KNO3-H2SO4 are very strong. Many nitro groups can be linked with phenyl groups in CL-PPSQ, but with low molecular mass, fracture occurs in siloxane segment. However, the Mn of the product NO2-PPSQ sharply drops by 50% compared with that of CL-PPSQ, so the nitration reagents can break the cyclic structure of CL-PPSQ. The nitrating reagents of HNO3-KNO3 and CH3COOH-KNO3 have no nitration effects on CL-PPSQ. At last, NO2-CL-PPSQ was prepared using (CH3CO2O-HNO3 because of the moderate nitration process and ability. The cyclic structure of PPSQ is remained, although the number of —NO2 group is not too much. At the same time, the nitration mechanism using different nitration reagents was analyzed. A certain amount of NO2+, which is a kind of activator owning strong nitration ability, can be found in the fuming nitric acid and H2SO4-HNO3(KNO3 systems. As to the (CH3CO2O-HNO3 system, the main activator is CH3COONO2.

Inversion of General Cyclic Heptadiagonal Matrices

Directory of Open Access Journals (Sweden)

A. A. Karawia

2013-01-01

Full Text Available We describe a reliable symbolic computational algorithm for inverting general cyclic heptadiagonal matrices by using parallel computing along with recursion. The computational cost of it is operations. The algorithm is implementable to the Computer Algebra System (CAS such as MAPLE, MATLAB, and MATHEMATICA. Two examples are presented for the sake of illustration.

Cyclic Loading of Growing Tissue in a Bioreactor: Mathematical Model and Asymptotic Analysis

KAUST Repository

Pohlmeyer, J. V.; Cummings, L. J.

2013-01-01

A simplified 2D mathematical model for tissue growth within a cyclically-loaded tissue engineering scaffold is presented and analyzed. Such cyclic loading has the potential to improve yield and functionality of tissue such as bone and cartilage when

Anti-cyclic regulation of the Ukrainian economy under current conditions of the international markets volatility

Directory of Open Access Journals (Sweden)

Volodymyr Satsyk

2009-04-01

Full Text Available In the article there are considered the theoretical and methodological basis of anti-cyclic regulation of the countries’ economy under conditions of the world economy globalization. It suggests the analysis of practices of implementing of anti-cyclic policy in highly developed states, its defining features and directions under current global financial and economic crisis. There has been researched a practical toolkit of economic cycles diagnostics and cyclic fluctuations of total business activity in Ukraine based on this study. There are suggested recommendations concerning the formation of the effective mechanism of anti-cyclic regulation of the Ukrainian economy.

Application of cyclic J-integral to low cycle fatigue crack growth of Japanese carbon steel pipe

Energy Technology Data Exchange (ETDEWEB)

Miura, N.; Fujioka, T.; Kashima, K. [and others

1997-04-01

Piping for LWR power plants is required to satisfy the LBB concept for postulated (not actual) defects. With this in mind, research has so far been conducted on the fatigue crack growth under cyclic loading, and on the ductile crack growth under excessive loading. It is important, however, for the evaluation of the piping structural integrity under seismic loading condition, to understand the fracture behavior under dynamic and cyclic loading conditions, that accompanies large-scale yielding. CRIEPI together with Hitachi have started a collaborative research program on dynamic and/or cyclic fracture of Japanese carbon steel (STS410) pipes in 1991. Fundamental tensile property tests were conducted to examine the effect of strain rate on tensile properties. Cracked pipe fracture tests under some loading conditions were also performed to investigate the effect of dynamic and/or cyclic loading on fracture behavior. Based on the analytical considerations for the above tests, the method to evaluate the failure life for a cracked pipe under cyclic loading was developed and verified. Cyclic J-integral was introduced to predict cyclic crack growth up to failure. This report presents the results of tensile property tests, cracked pipe fracture tests, and failure life analysis. The proposed method was applied to the cracked pipe fracture tests. The effect of dynamic and/or cyclic loading on pipe fracture was also investigated.

Short analysis of a progressive distorsion problem (tension and cyclic torsion)

International Nuclear Information System (INIS)

Roche, Roland.

1978-06-01

Tests on ratcheting (or progressive distorsion) are in progress in Saclay. A thin tube is subjected to a constant tensile load and to a cyclic twist. The present paper is a short theoretial analysis of that case. A uniform strain and stress field is considered with a constant tensile stress P (primary stress) and a cyclic shearing strain. The shearing strain is known by the corresponding elastic equivalent stress intensity (TRESCA criterion). The cyclic range of the stress intensity is ΔQ (secondary stress range). Are examined the shake down condition and the incremental elongations with different constitutive equations of the material. Special attention is given to perfect plasticity and bilinear kinematic hardening results are presented, but it is believed that these materials mathematical models are simplistic and special experimental tests are proposed [fr

Temporal analysis of static priority preemptive scheduled cyclic streaming applications using CSDF models

NARCIS (Netherlands)

Kurtin, Philip Sebastian; Bekooij, Marco Jan Gerrit

2016-01-01

Real-time streaming applications with cyclic data dependencies that are executed on multiprocessor systems with processor sharing usually require a temporal analysis to give guarantees on their temporal behavior at design time. Current accurate analysis techniques for cyclic applications that are

The solvent effect on the enthalpy of hydrolysis of cyclic adenosine 3',5'-monophosphate : a quantum chemical study

NARCIS (Netherlands)

Scheffers - Sap, Miek; Buck, H.M.

1978-01-01

The solvent effect on the enthalpy of hydrolysis has been studied by the Extended-Hückel method for the hydrolysis reactions of cyclic adenosine 3',5'-monophosphate (cyclic 3',5'-AMP) and related cyclic phosphate diesters. The results show that the difference in enthalpy of hydrolysis between cyclic

Detection of Corrosion Resistance of Components in Cyclic Salt Spray

Directory of Open Access Journals (Sweden)

Štefan Álló

2015-01-01

Full Text Available The aim of this research is, to investigate the influence of two types of cyclic salt spray tests on parts surface treated with galvanizing. On the selected components was performed the method Zn-Ni surface treating on the bath line. Subsequently were the components embedded in the corrosion chamber, where was performed two types of cyclic salt test. In the first test was performed 4 hour salt spray, 8 hours drying, 60 hours condensation and 24 hours drying. Once cycle lasted 96 hours, and it was repeated 4 times. During the second test was performed 2 hours salt spray, 2 hours condensation. The cycle was repeated 4 times, that means 96 hours. After the cycle was performed 72 hours free relaxation in the corrosion chamber, on 20–25 °C temperature. As the research showed, after the cyclic salt spray was no red corrosion on the selected components. The white corrosion appeared only slightly.

Annotating and Interpreting Linear and Cyclic Peptide Tandem Mass Spectra.

Science.gov (United States)

Niedermeyer, Timo Horst Johannes

2016-01-01

Nonribosomal peptides often possess pronounced bioactivity, and thus, they are often interesting hit compounds in natural product-based drug discovery programs. Their mass spectrometric characterization is difficult due to the predominant occurrence of non-proteinogenic monomers and, especially in the case of cyclic peptides, the complex fragmentation patterns observed. This makes nonribosomal peptide tandem mass spectra annotation challenging and time-consuming. To meet this challenge, software tools for this task have been developed. In this chapter, the workflow for using the software mMass for the annotation of experimentally obtained peptide tandem mass spectra is described. mMass is freely available (http://www.mmass.org), open-source, and the most advanced and user-friendly software tool for this purpose. The software enables the analyst to concisely annotate and interpret tandem mass spectra of linear and cyclic peptides. Thus, it is highly useful for accelerating the structure confirmation and elucidation of cyclic as well as linear peptides and depsipeptides.

Production of isomers by the cyclic activation method

International Nuclear Information System (INIS)

Salaita, G.N.; Eapen, P.K.

1974-01-01

The isomeric states formation cross sections for 14.8 MeV neutron reactions in Mg, Al, As, Y, In, Hf, Tl, Pb, and Bi were measured using the cyclic activation technique and a high resolution Ge(Li) detector. Isomeric activities originating from the various isotopes of lead and thallium were separated by proper choice of cyclic timing parameters and energy discrimination. Long lived isomeric and ground state activities were investigated through conventional activation method. The isomeric cross section ratios, sigma/sub m//sigma/sub g/ for six elements, were measured and compared to the theoretical predictions of the Huizenga-Vandenbosch method. The half-lives of short-lived activities were determined using a wide range time-to-pulse height converter and a multi-channel analyzer

Analysis and characterization of cyclic-scale compensated analog-to-digital converters

International Nuclear Information System (INIS)

Gatti, E.; Manfredi, P.F.; Marino, D.

1979-01-01

The authors discuss characteristics and limitations of cyclic-scale compensated analog-to-digital converters. After summarizing the behaviour of the method implemented in an ideal way, they show how the inaccuracies in the auxillary analog levels affect the real design. Having stated under what approximations and with what cares a cyclic-scale compensated converter approaches the ideal case of channels having equal profiles, the consequences of this property, are studied. (Auth.)

G-control fatigue testing for cyclic crack propagation in composite structures

DEFF Research Database (Denmark)

Manca, Marcello; Berggreen, Christian; Carlsson, Leif A.

2015-01-01

This paper presents a computer controlled testing methodology called “The G-control Method” which allows cyclic crack growth testing using real-time control of the cyclic energy release rate. The advantages of using this approach are described and compared with traditional fatigue testing methods...... that the G-control method allows fatigue testing at a constant range of energy release rates leading to a constant crack propagation rate....

Sedimentary cyclicity in early Pleistocene, evaporitic, playa-lake lacustrine deposits in the Guadix-Baza basin (Betic Cordillera, Spain); Ciclicidad sedimentaria en depositos lacustres evaporiticos tipo playa-lake del Pleistoceno inferior en la cuenca de Guadix-Baza (Cordillera Betica, Espana)

Energy Technology Data Exchange (ETDEWEB)

Garcia Aguilar, J. M.; Guera-Menchan, A.; Serrano, F.; Palmqvist, P.

2013-06-01

The Guadix-Baza basin (Betic Cordillera, southern Spain) contains in its eastern sector an early Pleistocene (Gelasian and lowermost Calabrian) sedimentary unit that was deposited in a shallow lacustrine environment. Given that the chronological limits of this unit lie between 2.5 and 1.6 Ma BP, the thickness of its preserved sediments (400 m) and high sedimentation rate (44.4 cm/ka) are remarkable. Numerous sedimentary cycles marked by an alternation of marls and sands are commonly found in the marginal sectors and marls and gypsum in the central sector, which would owe their origins to permanent flooding and evaporation/ re-flooding phases due to global climatic changes. Spectral analyses carried out using Fourier transform have revealed the existence of temporary frequencies associated with sedimentary cycles of between 0.2 and 5.2 ka. The origin of these cycles may be associated with variations in solar radiation and oscillations in the Moons orbital position, which would induce global climatic changes resulting in the rise and fall of the water table of the lake. Autocorrelation analyses conducted separately on the marly and evaporitic levels support this conclusion, as they indicate the existence of significant direct correlations between about 4 to 12 sedimentary cycles, which would correspond to repetitions of the stratigraphic series over a time span of 1.3 to 4 ka. (Author)

Small-Scale Cyclic Tests on Nonslender Piles Situated in Sand

DEFF Research Database (Denmark)

Sørensen, Søren Peder Hyldal; Ibsen, Lars Bo

In the period from August 2011 till October 2011 a series of small-scale tests on pile foundations has been conducted at Aalborg University. In all the tests, the piles have been exposed to cyclic loading consisting of 20-25 load cycles and all the tests have been conducted in a pressure tank....... The objective of the tests has been to investigate the effect of pile diameter, length to diameter ratio and cyclic loading on the soil response for non-slender piles in sand....

Study on the change of cyclic nucleotide in mice with yang vacuity disease

International Nuclear Information System (INIS)

Zhu Xinhua; Shen Ling; Wang Shuguang

2002-01-01

To study the relation between Yang Vacuity disease happening, development and cyclic nucleotide response, and prove curative effects of some assisting Yang drug, the plasma cAMP, cGMP and cAMP/cGMP levels were detected by radioimmunoassay in the Yang Vacuity group and curing group. Results: showed: (1) Yang Vacuity group: the symptoms were clear, death rate was high, the plasma cAMP and cAMP/cGMP increased obviously, it suggests that cyclic nucleotide was imbalance. (2) Curing group: the symptoms of Yang Vacuity disease were improved obviously, death rate dropped, cAMP declined, cGMP increased, while cAMP/cGMP reached the normal level, it showed that cyclic nucleotide of the body had altered greatly. (3) It is a reference target for Yang Vacuity. (4) Assisting yang drug (Sini Decoction) had a close relation with correcting imbalance of cyclic nucleotide

Chemotaxis to cyclic AMP and folic acid is mediated by different G proteins in Dictyostelium discoideum

NARCIS (Netherlands)

Kesbeke, Fanja; Haastert, Peter J.M. van; Wit, René J.W. de; Snaar-Jagalska, B. Ewa

1990-01-01

Mutant Frigid A (fgdA) of Dictyostelium discoideum is defective in a functional Gα2 subunit of a G protein and is characterized by a complete blockade of the cyclic AMP-mediated sensory transduction steps, including cyclic AMP relay, chemotaxis and the cyclic GMP response. Folic acid-mediated

A constitutive model for AS4/PEEK thermoplastic composites under cyclic loading

Science.gov (United States)

Rui, Yuting; Sun, C. T.

1990-01-01

Based on the basic and essential features of the elastic-plastic response of the AS4/PEEK thermoplastic composite subjected to off-axis cyclic loadings, a simple rate-independent constitutive model is proposed to describe the orthotropic material behavior for cyclic loadings. A one-parameter memory surface is introduced to distinguish the virgin deformation and the subsequent deformation process and to characterize the loading range effect. Cyclic softening is characterized by the change of generalized plastic modulus. By the vanishing yield surface assumption, a yield criterion is not needed and it is not necessary to consider loading and unloading separately. The model is compared with experimental results and good agreement is obtained.

Thermal and mechanical cyclic loading of thick spherical vessels made of transversely isotropic materials

International Nuclear Information System (INIS)

Komijani, M.; Mahbadi, H.; Eslami, M.R.

2013-01-01

The aim of this paper is to obtain the dependency of the ratcheting, reversed plasticity, or shakedown behavior of spherical vessels made of some anisotropic materials to the stress category of imposed cyclic loading. The Hill anisotropic yield criterion with the kinematic hardening theories of plasticity based on the Prager and Armstrong–Frederick models are used to predict the yield of the vessel and obtain the plastic strains. An iterative numerical method is used to simulate the cyclic loading behavior of the structure. The effect of mean and amplitude of the mechanical and thermal loads on cyclic behavior and ratcheting rate of the vessel is investigated respectively. The ratcheting rate for the vessels made of transversely isotropic material is evaluated for the various ratios of anisotropy. -- Highlights: ► Cyclic loading analysis of anisotropic spheres is assessed. ► Using the Prager model results in ratcheting. ► Armstrong-Frederick model predicts ratcheting for load controlled cyclic loadings. ► The A-F model predicts ratcheting to a stabilized cycle for thermal loadings

Past Holocene detritism quantification and modeling from lacustrine archives in order to deconvoluate human-climate interactions on natural ecosystem over long time-scale

Science.gov (United States)

Simonneau, Anaëlle; Chapron, Emmanuel; Di Giovanni, Christian; Galop, Didier; Darboux, Frédéric

2014-05-01

Water budget is one of the main challenges to paleoclimate researchers in relation to present-day global warming and its consequences for human societies. Associated soil degradation and erosion are thereby becoming a major concern in many parts of the world and more particularly in the Alps. Moreover, humans are considered as geomorphologic agents since few thousand years and it is now recognized that such an impact on natural ecosystem profoundly modified soils properties as well as aquatic ecosystems dynamics over long-term periods. The quantification of such inference over long time-scale is therefore essential to establish new policies to reduce mechanic soil erosion, which is one of the dominant processes in Europe, and anticipate the potential consequences of future climate change on hydric erosion. The mechanical erosion of continental surfaces results from climatic forcing, but can be amplified by the anthropogenic one. We therefore suggest that quantifying and modelling soil erosion processes within comparable Holocene lacustrine archives, allows to estimate and date which and when past human activities have had an impact on soil fluxes over the last 10000 years. Based on the present-day geomorphology of the surrounding watershed and the evolution of the vegetation cover during the Holocene, we develop an interdisciplinary approach combining quantitative organic petrography (i.e. optical characterization and quantification of soil particles within lake sediments) with high-resolution seismic profiling, age-depth models on lacustrine sediment cores and soil erosional susceptibility modeling, in order to estimate the annual volume of soil eroded over the last 10000 years, and in fine to quantify the volume of human-induced soil erosion during the Holocene period. This method is applied to close but contrasted mountainous lacustrine environments from the western French Alps: lakes Blanc Huez and Paladru, sensitive to same climatic influences but where past

True Triaxial Experimental Study of Rockbursts Induced By Ramp and Cyclic Dynamic Disturbances

Science.gov (United States)

Su, Guoshao; Hu, Lihua; Feng, Xiating; Yan, Liubin; Zhang, Gangliang; Yan, Sizhou; Zhao, Bin; Yan, Zhaofu

2018-04-01

A modified rockburst testing system was utilized to reproduce rockbursts induced by ramp and cyclic dynamic disturbances with a low-intermediate strain rate of 2 × 10-3-5 × 10-3 s-1 in the laboratory. The experimental results show that both the ramp and cyclic dynamic disturbances play a significant role in inducing rockbursts. In the tests of rockbursts induced by a ramp dynamic disturbance, as the static stress before the dynamic disturbance increases, both the strength of specimens and the kinetic energy of the ejected fragments first increase and then decrease. In the tests of rockbursts induced by a cyclic dynamic disturbance, there exists a rockburst threshold of the static stress and the dynamic disturbance amplitude, and the kinetic energy of the ejected fragments first increases and then decreases as the cyclic dynamic disturbance frequency increases. The main differences between rockbursts induced by ramp dynamic disturbances and those induced by cyclic dynamic disturbances are as follows: the rockburst development process of the former is characterized by an impact failure feature, while that of the latter is characterized by a fatigue failure feature; the damage evolution curve of the specimen of the former has a leap-developing form with a significant catastrophic feature, while that of the latter has an inverted S-shape with a remarkable fatigue damage characteristic; the energy mechanism of the former involves the ramp dynamic disturbance giving extra elastic strain energy to rocks, while that of the latter involves the cyclic dynamic disturbance decreasing the ultimate energy storage capacity of rocks.

Breaking antidunes: Cyclic behavior due to hysteresis

DEFF Research Database (Denmark)

Deigaard, Rolf

2006-01-01

The cyclic behavior of breaking antidunes (growth, breaking of surface wave, obliteration) is investigated by use of a numerical model. The model includes the transition between supercritical and transcritical flow. As the antidune grows the flow becomes transcritical and a hydraulic jump is form...

Driving Force Based Design of Cyclic Distillation

DEFF Research Database (Denmark)

Nielsen, Rasmus Fjordbak; Huusom, Jakob Kjøbsted; Abildskov, Jens

2017-01-01

with mixed phase feeds. A range of binary test cases, benzene toluene, methanol water, and ethanol water, are evaluated. The advantage of the design approach in cyclic distillation is shown to be analogous to the advantages obtained in conventional continuous distillation, including a minimal utility...

Cyclic response and early damage evolution in multiaxial cyclic loading of 316L austenitic steel

Czech Academy of Sciences Publication Activity Database

Mazánová, Veronika; Škorík, Viktor; Kruml, Tomáš; Polák, Jaroslav

2017-01-01

Roč. 100, JUL (2017), s. 466-476 ISSN 0142-1123 R&D Projects: GA MŠk LM2015069; GA MŠk(CZ) LQ1601; GA ČR(CZ) GA13-23652S; GA ČR GA15-08826S Institutional support: RVO:68081723 Keywords : 316L steel * Crack initiation * Cyclic plasticity * Damage mechanism * Multiaxial straining Subject RIV: JL - Materials Fatigue, Friction Mechanics OBOR OECD: Audio engineering, reliability analysis Impact factor: 2.899, year: 2016

Pointillist, Cyclical, and Overlapping: Multidimensional Facets of Time in Online Learning

Directory of Open Access Journals (Sweden)

Pekka Ihanainen

2011-11-01

Full Text Available A linear, sequential time conception based on in-person meetings and pedagogical activities is not enough for those who practice and hope to enhance contemporary education, particularly where online interactions are concerned. In this article, we propose a new model for understanding time in pedagogical contexts. Conceptual parts of the model will be employed as a “cultural technology” to help us relate to evolving phenomena, both physical and virtual. We label these constructs as pointillist, cyclical, and overlapping times.Pointillist time and learning takes place in “dots” of actions that consist of small, discrete moments (e.g., tweeting. Producing, receiving, and sharing ideas in this context are separate points in each actor’s timeline. Cyclical time and learning emerges from intensive periods, which are highly visible in online forums. This construct reveals itself through interactions that often exist in multiple online environments. Overlapping time and learning involves various configurations of linear, pointillist, and cyclical layers, which are mainly evident through the simultaneous uses of social communication technologies.Pointillist, cyclical, and overlapping time constructs enable new orientations for conceptualizing time in pedagogy. In this article we also introduce de-, re-, and en- modes of these pedagogies that connect with approaches to meet the needs of learners for individualization, personalization, and cyborgization.

Modeling of Cyclic Strength for the Asphalt Concrete Considering Damage Accumulation

Directory of Open Access Journals (Sweden)

Alibai Iskakbayev

2017-12-01

Full Text Available The expression is obtained for determination of cyclic tensile strength for asphalt concrete, which considers damage accumulation and history of loading, using the long-term strength curve for asphalt concrete obtained according to the test results of more than 110 samples to failure at stresses from 0.05 to 0.31 MPa and by introduction of damage kernel in this paper. Cyclic strength depends on the stress, parameters of long-term strength, frequency of loading, durations of loading and relax periods, and ratio of loading period to the long-term strength. Evaluation of accuracy for the obtained expression for the cyclic strength has been performed by comparison with the results of a series for experimental tests of asphalt concrete samples at a temperature of 22 °С and cyclic loading conditions. The stress is 0.31 MPa, and the durations of loading and relax periods are 5 and 60 s, respectively. Calculations performed with the obtained expressions at real road conditions (the stress is 0.31 MPa, and the durations of loading and relax periods are 0.1 and 9.9 s respectively showed the possibility of its use for the prediction of fatigue (multicyclic strength of an asphalt concrete pavement for a highway.

Atrial natriuretic peptide receptor heterogeneity and effects on cyclic GMP accumulation

International Nuclear Information System (INIS)

Leitman, D.C.

1988-01-01

The effects of atrial natriuretic peptide (ANP), oxytocin (OT) and vasopressin (AVP) on guanylate cyclase activity and cyclic GMP accumulation were examined, since these hormones appear to be intimately associated with blood pressure and intravascular volume homeostasis. ANP was found to increase cyclic GMP accumulation in ten cell culture systems, which were derived from blood vessels, adrenal cortex, kidney, lung, testes and mammary gland. ANP receptors were characterized in intact cultured cells using 125 I-ANP 8-33 . Specific 125 I-ANP binding was saturable and of high affinity. Scratchard analysis of the binding data for all cell types exhibited a straight line, indicating that these cells possessed a single class of binding sites. Despite the presence of linear Scatchard plots, these studies demonstrated that cultured cells possess two functionally and physically distinct ANP-binding sites. Most of the ANP-binding sites in cultured cells have a molecular size of 66,000 daltons under reducing conditions. The identification of cultured cell types in which hormones (ANP and oxytocin) regulate guanylate cyclase activity and increase cyclic GMP synthesis will provide valuable systems to determine the mechanisms of hormone-receptor coupling to guanylate cyclase and the cellular processes regulated by cyclic GMP

Cyclic joint remote state preparation in noisy environment

Science.gov (United States)

Zhang, Chang-yue; Bai, Ming-qiang; Zhou, Si-qi

2018-06-01

We propose a scheme of cyclic joint remote state preparation for three sides, which takes advantage of three GHZ states to compose product state as quantum channel. Suppose there are six legitimate participants, says Alice, Bob, Charlie, David, Emma and Fred in the scheme. It can be shown that Alice and David can remotely prepare a single-qubit state on Bob's side; meanwhile, Bob and Emma can remotely prepare a desired quantum state on Charlie's side, and Charlie and Fred can also remotely prepare a single-qubit state on Alice's side at the same time. Further, it can be achieved in the opposite direction of the cycle by changing the quantum channel. Based on it, we generalize this protocol to N (N≥3) sides utilizing three multi-qubit GHZ-type states as quantum channel. Therefore, the scheme can achieve cyclic joint remote state preparation, which remotely prepares N states in quantum network with N-party, simultaneously. In addition, we consider that the effect of amplitude-damping noise of the initial states is prepared in four different laboratory. Clearly, we use fidelity to describe how much information has been lost in the cyclic process. Our investigation about the effect of noise shows that the preparing of the initial state in different laboratories will affect the loss of information.

Determination of silver using cyclic epithermal neutron activation analysis

International Nuclear Information System (INIS)

Pun, T.H.; Landsberger, S.

2012-01-01

A fast pneumatic transfer facility was installed in Nuclear Engineering Teaching Laboratory (NETL) of the University of Texas at Austin for the purpose of cyclic thermal and epithermal neutron activation analysis. In this study efforts were focused on the evaluation of cyclic epithermal neutron activation analysis (CENAA). Various NIST and CANMET certified materials were analyzed by the system. Experiment results showed 110 Ag with its 25 s half-life as one of the isotopes favored by the system. Thus, the system was put into practical application in identifying silver in metallic ores. Comparison of sliver concentrations as determined by CENAA in CANMET certified reference materials gave very good results. (author)

Intramolecular cascade rearrangements of enynamine derived ketenimines: access to acyclic and cyclic amidines.

Science.gov (United States)

Chauhan, Dinesh Pratapsinh; Varma, Sreejith J; Gudem, Mahesh; Panigrahi, Nihar; Singh, Khushboo; Hazra, Anirban; Talukdar, Pinaki

2017-06-07

Copper-catalyzed reaction of enynamines with sulfonylazides provides acyclic and cyclic amidines. Nucleophilic addition of the tethered amino group on the in situ generated ketenimine forms a six-membered cyclic zwitterionic intermediate which facilitates migration of the tethered amino group to the C 5 -center giving the acyclic amidine. On the other hand, migration of a substituent on the amino group to C 2 - and C 4 -centers results in the formation of cyclic amidines. Computational studies were carried out to validate the mechanism which indicates that the product distribution of the process depends on the substitutions on the enynamine backbone.

Cyclical Annealing Technique To Enhance Reliability of Amorphous Metal Oxide Thin Film Transistors.

Science.gov (United States)

Chen, Hong-Chih; Chang, Ting-Chang; Lai, Wei-Chih; Chen, Guan-Fu; Chen, Bo-Wei; Hung, Yu-Ju; Chang, Kuo-Jui; Cheng, Kai-Chung; Huang, Chen-Shuo; Chen, Kuo-Kuang; Lu, Hsueh-Hsing; Lin, Yu-Hsin

2018-02-26

This study introduces a cyclical annealing technique that enhances the reliability of amorphous indium-gallium-zinc-oxide (a-IGZO) via-type structure thin film transistors (TFTs). By utilizing this treatment, negative gate-bias illumination stress (NBIS)-induced instabilities can be effectively alleviated. The cyclical annealing provides several cooling steps, which are exothermic processes that can form stronger ionic bonds. An additional advantage is that the total annealing time is much shorter than when using conventional long-term annealing. With the use of cyclical annealing, the reliability of the a-IGZO can be effectively optimized, and the shorter process time can increase fabrication efficiency.

The influence of cyclic structure on the radiolysis of hydrocarbons

International Nuclear Information System (INIS)

Foeldiak, G.; Cserep, Gy.; Horvath, Zs.; Wojnarovits, L.

1975-01-01

Aliphatic and cyclic C 3 -C 12 alkanes and alkenes have been irradiated in liquid phase by a 60 Co-γ-source with the nominal activity of 80 000 Ci. The dose rate was 1-2 Mrad/hr, the doses were between 0 and 10 Mrad. The following conclusions can be drawn from the experiments: 1., While no significant difference can be observed between radiolytic decomposition of n-hydrocarbon homologues, that of cyclic hydrocarbons is the function of the size of the ring. 2., Reactivity of cyclic hydrocarbons is influenced not only by their surplus enthalpy of formation (strain energy) but also by the individual components of this surplus enthalpy, e.g. bond deformation or repulsion between hydrogen atoms. 3., The overall yield of decomposition of higher than C 4 straightchain and cyclic alkanes activated by radiation and reacting via either C-C or C-H fission is approximately constant, with a G value of 6.5+-0.5. The structure of the molecules affects mainly the ratio of C-C and C-H bond rupture, i.e. these two processes are in competition. 4., Hydrogen yields from alkenes are affected mainly by the order and number of allylic C-H bonds, and by the possibility of the formation of allyl-type radicals. This latter is facilitated by ''free'' rotation in the case of open-chain hydrocarbons whereas it is hindered in the case of small and medium size cycles. (K.A.)

Isotopic Exchange HPLC-HRMS/MS Applied to Cyclic Proanthocyanidins in Wine and Cranberries

Science.gov (United States)

Longo, Edoardo; Rossetti, Fabrizio; Scampicchio, Matteo; Boselli, Emanuele

2018-01-01

Cyclic B-type proanthocyanidins in red wines and grapes have been discovered recently. However, proanthocyanidins of a different chemical structure (non-cyclic A-type proanthocyanidins) already known to be present in cranberries and wine possess an identical theoretical mass. As a matter of fact, the retention times and the MS/MS fragmentations found for the proposed novel cyclic B-type tetrameric proanthocyanidin in red wine and the known tetrameric proanthocyanidin in a cranberry extract are herein shown to be identical. Thus, hydrogen/deuterium (H/D) exchange was applied to HPLC-HRMS/MS to confirm the actual chemical structure of the new oligomeric proanthocyanidins. The comparison of the results in water and deuterium oxide and between wine and cranberry extract indicates that the cyclic B-type tetrameric proanthocyanidin is the actual constituent of the recently proposed novel tetrameric species ([C60H49O24]+, m/z 1153.2608). Surprisingly, the same compound was also identified as the main tetrameric proanthocyanidin in cranberries. Finally, a totally new cyclic B-type hexameric proanthocyanidin ([C90H73O36]+, m/z 1729.3876) belonging to this novel class was identified for the first time in red wine. [Figure not available: see fulltext.

Cyclic deformation and phase transformation of 6Mo superaustenitic stainless steel

Science.gov (United States)

Wang, Shing-Hoa; Wu, Chia-Chang; Chen, Chih-Yuan; Yang, Jer-Ren; Chiu, Po-Kay; Fang, Jason

2007-08-01

A fatigue behavior analysis was performed on superaustenitic stainless steel UNS S31254 (Avesta Sheffield 254 SMO), which contains about 6wt.% molybdenum, to examine the cyclic hardening/softening trend, hysteresis loops, the degree of hardening, and fatigue life during cyclic straining in the total strain amplitude range from 0.2 to 1.5%. Independent of strain rate, hardening occurs first, followed by softening. The degree of hardening is dependent on the magnitude of strain amplitude. The cyclic stress-strain curve shows material softening. The lower slope of the degree of hardening versus the strain amplitude curve at a high strain rate is attributed to the fast development of dislocation structures and quick saturation. The ɛ martensite formation, either in band or sheath form, depending on the strain rate, leads to secondary hardening at the high strain amplitude of 1.5%.

Stratigraphy of the layered terrain in Valles Marineris, Mars

Science.gov (United States)

Komatsu, G.; Strom, Roger G.

1991-01-01

The layered terrain in Valles Marineris provides information about its origin and the geologic history of this canyon system. Whether the terrain is sedimentary material deposited in a dry or lacustrine environment, or volcanic material related to the tectonics of the canyon is still controversial. However, recent studies of Gangis Layered Terrain suggests a cyclic sequence of deposition and erosion under episodic lacustrine conditions. The stratigraphic studies are extended to four other occurrences of layered terrains in Valles Marineris in an attempt to correlate and distinguish between depositional environments. The Juvantae Chasma, Hebes Chasma, Ophir and Candor Chasmata, Melas Chasma, and Gangis Layered Terrain were examined. Although there are broad similarities among the layered terrains, no two deposits are exactly alike. This suggests that there was no synchronized regional depositional processes to form all the layered deposits. However, the similar erosional style of the lower massive weakly bedded unit in Hebes, Gangis, and Ophir-Candor suggests it may have been deposited under similar circumstances.

Accelerated cyclic corrosion tests

Directory of Open Access Journals (Sweden)

Prošek T.

2016-06-01

Full Text Available Accelerated corrosion testing is indispensable for material selection, quality control and both initial and residual life time prediction for bare and painted metallic, polymeric, adhesive and other materials in atmospheric exposure conditions. The best known Neutral Salt Spray (NSS test provides unrealistic conditions and poor correlation to exposures in atmosphere. Modern cyclic accelerated corrosion tests include intermittent salt spray, wet and dry phases and eventually other technical phases. They are able to predict the material performance in service more correctly as documented on several examples. The use of NSS should thus be restricted for quality control.

Cyclic [G(2',5')pA(3',5')p] is the metazoan second messenger produced by DNA-activated cyclic GMP-AMP synthase.

Science.gov (United States)

Gao, Pu; Ascano, Manuel; Wu, Yang; Barchet, Winfried; Gaffney, Barbara L; Zillinger, Thomas; Serganov, Artem A; Liu, Yizhou; Jones, Roger A; Hartmann, Gunther; Tuschl, Thomas; Patel, Dinshaw J

2013-05-23

Recent studies identified cyclic GMP-AMP (cGAMP) as a metazoan second messenger triggering an interferon response. cGAMP is generated from GTP and ATP by cytoplasmic dsDNA sensor cGAMP synthase (cGAS). We combined structural, chemical, biochemical, and cellular assays to demonstrate that this second messenger contains G(2',5')pA and A(3',5')pG phosphodiester linkages, designated c[G(2',5')pA(3',5')p]. We show that, upon dsDNA binding, cGAS is activated through conformational transitions, resulting in formation of a catalytically competent and accessible nucleotide-binding pocket for generation of c[G(2',5')pA(3',5')p]. We demonstrate that cyclization occurs in a stepwise manner through initial generation of 5'-pppG(2',5')pA prior to cyclization to c[G(2',5')pA(3',5')p], with the latter positioned precisely in the catalytic pocket. Mutants of cGAS dsDNA-binding or catalytic pocket residues exhibit reduced or abrogated activity. Our studies have identified c[G(2',5')pA(3',5')p] as a founding member of a family of metazoan 2',5'-containing cyclic heterodinucleotide second messengers distinct from bacterial 3',5' cyclic dinucleotides. Copyright © 2013 Elsevier Inc. All rights reserved.

Cyclic Cratonic Carbonates and Phanerozoic Calcite Seas.

Science.gov (United States)

Wilkinson, Bruce H.

1982-01-01

Discusses causes of cyclicity in cratonic carbonate sequences and evidence for and potential significance of postulated primary calcite sediment components in past Paleozoic seas, outlining problems, focusing on models explaining existing data, and identifying background. Future sedimentary geologists will need to address these and related areas…

Steady state oxygen reduction and cyclic voltammetry

DEFF Research Database (Denmark)

Rossmeisl, Jan; Karlberg, Gustav; Jaramillo, Thomas

2008-01-01

The catalytic activity of Pt and Pt3Ni for the oxygen reduction reaction is investigated by applying a Sabatier model based on density functional calculations. We investigate the role of adsorbed OH on the activity, by comparing cyclic voltammetry obtained from theory with previously published ex...

Rotylenchulus reniformis

African Journals Online (AJOL)

STORAGESEVER

2008-09-17

Sep 17, 2008 ... We investigated this unexpected outcome by amplifying, cloning and sequencing two ... the first internal transcribed spacer of the nuclear riboso- mal DNA ... from Japan contained no males and was considered parthenogenic ...

Martensitic Transformation in Ultrafine-Grained Stainless Steel AISI 304L Under Monotonic and Cyclic Loading

Directory of Open Access Journals (Sweden)

Heinz Werner Höppel

2012-02-01

Full Text Available The monotonic and cyclic deformation behavior of ultrafine-grained metastable austenitic steel AISI 304L, produced by severe plastic deformation, was investigated. Under monotonic loading, the martensitic phase transformation in the ultrafine-grained state is strongly favored. Under cyclic loading, the martensitic transformation behavior is similar to the coarse-grained condition, but the cyclic stress response is three times larger for the ultrafine-grained condition.

Eight-term cyclic phosphites as coke deposit inhibitors and a method for producing them

Energy Technology Data Exchange (ETDEWEB)

Vershinin, P.V.; Chebotareva, E.G.; Kadyrova, V.Kh.; Kirpichnikov, P.A.; Pozdnev, V.V.; Vershinin, Yu.P.; Zharkova, V.M.

1982-01-01

It is proposed that a eight-term cyclic phosphite formula be used where R = methyl, R' = tertiary-butyl or alpha-methylcyclohexyl, R'' = tertiary-butyl, R''' = hydrogen, methyl, tertiary-butyle, bromine, X = methylene and sulfur as coke deposit inhibitors in the pyrolysis of petroleum raw materials. A method for producing the eight-term cyclic phosphite formula is proposed where a cyclic chlorophosphite formula interacts with a phenol formula in a medium of polar aprotic solvent using a base at 80-100 degrees.

Regulation of Maltodextrin Phosphorylase Synthesis in Escherichia coli by Cyclic Adenosine 3′, 5′-Monophosphate and Glucose1

Science.gov (United States)

Chao, Julie; Weathersbee, Carolyn J.

1974-01-01

Cyclic adenosine 3′, 5′-monophosphate (AMP) stimulates maltodextrin phosphorylase synthesis in Escherichia coli cells induced with maltose. A maximal effect occurs at 2 to 3 mM cyclic AMP. The action of cyclic AMP is specific, inasmuch as adenosine triphosphate, 3′-AMP, 5′-AMP, adenosine, and dibutyryl cyclic AMP are inactive. Glucose, α-methyl glucoside, 2-deoxyglucose, and pyridoxal 5′-phosphate repress maltodextrin phosphorylase synthesis. This repression is reversed by cyclic AMP. The action of cyclic AMP appears to be at the transcriptional level, since cyclic AMP fails to stimulate phosphorylase production in induced cells in which messenger ribonucleic acid synthesis has been arrested by rifampin or by inducer removal. The two other enzymes involved in the metabolism of maltose, amylomaltase and maltose permease, are also induced in this strain of E. coli and affected by glucose and cyclic AMP in a manner similar to phosphorylase. PMID:4358043

Understanding the Earth Systems: Expressions of Dynamic and Cyclic Thinking among University Students

Science.gov (United States)

Batzri, Or; Ben Zvi Assaraf, Orit; Cohen, Carmit; Orion, Nir

2015-01-01

In this two-part study, we examine undergraduate university students' expression of two important system thinking characteristics--dynamic thinking and cyclic thinking--focusing particularly on students of geology. The study was conducted using an Earth systems questionnaire designed to elicit and reflect either dynamic or cyclic thinking. The…

Dislocation structure evolution in 304L stainless steel and weld joint during cyclic plastic deformation

Energy Technology Data Exchange (ETDEWEB)

Wang, Hao; Jing, Hongyang; Zhao, Lei; Han, Yongdian; Lv, Xiaoqing [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Advanced Joining Technology, Tianjin 300072 (China); Xu, Lianyong, E-mail: xulianyong@tju.edu.cn [School of Materials Science and Engineering, Tianjin University, Tianjin 300072 (China); Tianjin Key Laboratory of Advanced Joining Technology, Tianjin 300072 (China)

2017-04-06

Dislocation structures and their evolution of 304L stainless steel and weld metal made with ER308L stainless steel welding wire subjected to uniaxial symmetric strain-controlled loading and stress-controlled ratcheting loading were observed by transmission electron microscopy (TEM). The correlation between the cyclic response and the dislocation structure has been studied. The experiment results show that the cyclic behaviour of base metal and weld metal are different. The cyclic behaviour of the base metal consists of primary hardening, slight softening and secondary hardening, while the weld metal shows a short hardening within several cycles followed by the cyclic softening behaviour. The microscopic observations indicate that in base metal, the dislocation structures evolve from low density patterns to those with higher dislocation density during both strain cycling and ratcheting deformation. However, the dislocation structures of weld metal change oppositely form initial complicated structures to simple patterns and the dislocation density gradually decrease. The dislocation evolution presented during the strain cycling and ratcheting deformation is summarized, which can qualitatively explain the cyclic behaviour and the uniaxial ratcheting behaviour of two materials. Moreover, the dislocation evolution in the two types of tests is compared, which shows that the mean stress has an effect on the rate of dislocation evolution during the cyclic loading.

Synergistic enhancing effect of N+C alloying on cyclic deformation behaviors in austenitic steel

Energy Technology Data Exchange (ETDEWEB)

Kang, J. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Zhang, F.C., E-mail: zfc@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Long, X.Y. [State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004 (China); Yang, Z.N. [National Engineering Research Center for Equipment and Technology of Cold Strip Rolling, Yanshan University, Qinhuangdao 066004 (China)

2014-07-29

Cyclic plastic and elastic strain controlled deformation behaviors of Mn18Cr7 austenitic steel with N0.6C0.3 synergistic enhancing alloying have been investigated using tension-compression low cycle fatigue and three-point bending high cycle fatigue testing. Results of cyclic deformation characteristic and fatigue damage mechanism have been compared to that in Mn12C1.2 steel. Mn18Cr7N0.6C0.3 steel always shows cyclic softening caused by enhanced planar sliding due to the interaction between N+C and the substitutional atoms as well as the dislocation, which is totally different from cyclic hardening in Mn12C1.2 steel caused by the interaction between C members of C–Mn couples with the dislocation. Enhanced effective stress is obtained due to the solid solution strengthening effect caused by the short range order at low strain amplitude while this effect does not work at high strain amplitude. Internal stress contributes most to the cyclic softening with the increase of strain amplitudes. Significant planar slip characteristic can be observed resulting from low stacking fault energy and high short range order effects in Mn18Cr7N0.6C0.3 steel and finally the parallel or intersecting thin sheets with dislocation tangles separated by dislocation free sheets are obtained with the prolonged cycles under cyclic elastic or plastic strain controlled fatigue testing. There exist amounts of small cracks on the surface of the Mn18Cr7N0.6C0.3 steel because fatigue crack initiation is promoted by the cyclic plastic strain localization. However, the zigzag configuration of the cracks reveals that the fatigue crack propagation is highly inhibited by the planar slip characteristic, which eventually improves the fatigue life.

The Interplay between Cyclic AMP, MAPK, and NF-κB Pathways in Response to Proinflammatory Signals in Microglia

Directory of Open Access Journals (Sweden)

Mousumi Ghosh

2015-01-01

Full Text Available Cyclic AMP is an important intracellular regulator of microglial cell homeostasis and its negative perturbation through proinflammatory signaling results in microglial cell activation. Though cytokines, TNF-α and IL-1β, decrease intracellular cyclic AMP, the mechanism by which this occurs is poorly understood. The current study examined which signaling pathways are responsible for decreasing cyclic AMP in microglia following TNF-α stimulation and sought to identify the role cyclic AMP plays in regulating these pathways. In EOC2 microglia, TNF-α produced a dramatic reduction in cyclic AMP and increased cyclic AMP-dependent PDE activity that could be antagonized by Rolipram, myristoylated-PKI, PD98059, or JSH-23, implicating a role for PDE4, PKA, MEK, and NF-κB in this regulation. Following TNF-α there were significant increases in iNOS and COX-2 immunoreactivity, phosphorylated ERK1/2 and NF-κB-p65, IκB degradation, and NF-κB p65 nuclear translocation, which were reduced in the presence of high levels of cyclic AMP, indicating that reductions in cyclic AMP during cytokine stimulation are important for removing its inhibitory action on NF-κB activation and subsequent proinflammatory gene expression. Further elucidation of the signaling crosstalk involved in decreasing cyclic AMP in response to inflammatory signals may provide novel therapeutic targets for modulating microglial cell activation during neurological injury and disease.

Methods of evaluation of thermal tolerance of cyclic sports athletes

Directory of Open Access Journals (Sweden)

Kish А.А.

2017-12-01

Full Text Available The purpose of the study is investigation of thermal stability in athletes of cyclic sports and assessment of its influence on physical working capacity under hyperthermia. Material and methods. 15 male athletes of cyclic sports who had the senior degree as minimum were included in the study Middle age 24,2±1,1 years. Work was performed in the climatic camera of the Center of sports medicine and rehabilitation in several stages, on each of which assessment of physical working capacity and a thermal condition of athletes was carried out. Results. In the real work the burdening action of the heating climate on indicators of physical working capacity and a thermal condition of athletes of cyclic sports is shown; the operating ranges of high temperatures are determined. Conclusion. The data obtained by means of the offered technique, confirm importance of definition of individual thresholds of shipping of a thermal state at athletes and the burdening action of a heat on their physical working capacity.

Doping effect of polyaniline/MWCNT composites on capacitance and cyclic stability of supercapacitors.

Science.gov (United States)

Karthikeyan, G; Sahoo, S; Nayak, G C; Das, C K

2012-03-01

Polyaniline doped by Zn2+ ions was synthesized as nanocomposites with multiwalled carbon nanotubes (MWCNT) by in-situ oxidative polymerization and investigated as electrode material for supercapacitors. The uniform coating of polyaniline on MWCNT was characterized by field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscopy (HRTEM). The effect of Zn2+ ions on nanocomposites were characterized by Fourier transform infrared (FTIR) spectroscopy. The electrochemical performances were investigated by cyclic voltammetry (CV), constant current charging/discharging cyclic test (CC) and electrochemical impedance spectroscopy (EIS) using a three-electrode system. The doped polyaniline composites show higher specific capacitance and better cyclic stability.

Cyclic loading tests on ceramic breeder pebble bed by discrete element modeling

Energy Technology Data Exchange (ETDEWEB)

Zhang, Hao [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230027 (China); Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Guo, Haibing; Shi, Tao [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Ye, Minyou [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230027 (China); Huang, Hongwen, E-mail: hhw@caep.cn [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); Li, Zhenghong, E-mail: inpcnyb@sina.com [Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900 (China); University of Science and Technology of China, Hefei 230027 (China)

2017-05-15

Highlights: • Methods of cyclic loading tests on the pebble beds were developed in DEM. • Size distribution and sphericity of the pebbles were considered for the specimen. • Mechanical responses of the pebble beds under cyclic loading tests were assessed. - Abstract: Complex mechanics and packing instability can be induced by loading operation on ceramic breeder pebble bed for its discrete nature. A numerical approach using discrete element method (DEM) is applied to study the mechanical performance of the ceramic breeder pebble bed under quasi-static and cyclic loads. A preloaded specimen can be made with servo-control mechanism, the quasi-static and dynamic stress-strain performances are studied during the tests. It is found that the normalized normal contact forces under quasi-static loads have the similar distributions, and increase with increasing loads. Furthermore, the relatively low volumetric strain can be absorbed by pebble bed after several loading and unloading cycles, but the peak normal contact force can be extremely high during the first cycle. Cyclic loading with target pressure is recommended for densely packing, irreversible volume reduction gradually increase with cycles, and the normal contact forces decrease with cycles.

Transcriptional regulation of the tyrosine hydroxylase gene by glucocorticoid and cyclic AMP

International Nuclear Information System (INIS)

Lewis, E.J.; Harrington, C.A.; Chikaraishi, D.M.

1987-01-01

Glucocorticoid and cyclic AMP increase tyrosine hydroxylase (TH) activity and mRNA levels in pheochromocytoma cultures. The transcriptional activity of the TH gene, as measured by nuclear run-on assay, is also increased when cultures are treated with the synthetic glucocorticoid dexamethasone or agents that increase intracellular cyclic AMP, such as forskolin and 8-BrcAMP. Both inducers effect transcriptional changes within 10 min after treatment and are maximal after 30 min for forskolin and after 60 min for dexamethasone. The 5' flanking sequences of the TH gene were fused to the bacterial gene chloramphenicol acetyltransferase (CAT), and the hybrid gene was transfected into pheochromocytoma cultures and GH 4 pituitary cells. In both cell lines, a region of the TH gene containing bases -272 to +27 conferred induction of CAT by cyclic AMP, but not by glucocorticoid. The same results were found when a region of the TH gene containing -773 to + 27 was used. Thus, the sequences required for induction of TH by cyclic AMP are contained within 272 bases of 5' flanking sequence, but sequences sufficient for glucocorticoid regulation are not contained with 773 bases

Cyclic loading tests on ceramic breeder pebble bed by discrete element modeling

International Nuclear Information System (INIS)

Zhang, Hao; Guo, Haibing; Shi, Tao; Ye, Minyou; Huang, Hongwen; Li, Zhenghong

2017-01-01

Highlights: • Methods of cyclic loading tests on the pebble beds were developed in DEM. • Size distribution and sphericity of the pebbles were considered for the specimen. • Mechanical responses of the pebble beds under cyclic loading tests were assessed. - Abstract: Complex mechanics and packing instability can be induced by loading operation on ceramic breeder pebble bed for its discrete nature. A numerical approach using discrete element method (DEM) is applied to study the mechanical performance of the ceramic breeder pebble bed under quasi-static and cyclic loads. A preloaded specimen can be made with servo-control mechanism, the quasi-static and dynamic stress-strain performances are studied during the tests. It is found that the normalized normal contact forces under quasi-static loads have the similar distributions, and increase with increasing loads. Furthermore, the relatively low volumetric strain can be absorbed by pebble bed after several loading and unloading cycles, but the peak normal contact force can be extremely high during the first cycle. Cyclic loading with target pressure is recommended for densely packing, irreversible volume reduction gradually increase with cycles, and the normal contact forces decrease with cycles.

Hydroecology of Amazonian lacustrine Arcellinida (testate amoebae): A case study from Lake Quistococha, Peru.

Science.gov (United States)

Patterson, R Timothy; Huckerby, Gail; Kelly, Thomas J; Swindles, Graeme T; Nasser, Nawaf A

2015-10-01

Organic rich sediments were obtained from seven core tops taken in Lake Quistococha, near the city of Iquitos in the Peruvian Amazon. Subsamples from 0 to 4cm depth in each core were analyzed under dissecting light microscopy to carry out the first investigation of Arcellinida (testate lobose amoebae) from a lacustrine environment in this ecologically important region. The fauna was characterized by a low diversity, low abundance community dominated by centropyxids. This fauna is similar to 'stressed' assemblages reported from temperate latitudes, except that test concentrations were two orders of magnitude lower than typical in temperate lakes. Principle arcellinidan stressors in Lake Quistococha likely include the low pH 4 conditions in the lake, and a general lack of suitable minerogenic material to construct tests in the organic rich lake substrate. The low pH conditions are the result of runoff and seepage of water high in dissolved organic carbon from the adjacent similarly low pH 4 terrestrial peatland. The dearth of minerogenic material is the result of the lake being isolated from riverine input for the past ∼2000 years, even during flooding events. Other limiting factors contributing to depressed arcellinidan populations may include nutrient supply, predation pressure, competition, and post-mortem taphonomic factors. Copyright © 2015 Elsevier GmbH. All rights reserved.

Cyclic mechanical behavior of 316L: Uniaxial LCF and strain-controlled ratcheting tests

International Nuclear Information System (INIS)

Facheris, G.; Janssens, K.G.F.

2013-01-01

Highlights: ► Characterization of cyclic plastic deformation behavior of plate and tubular 316L. ► Strain-controlled ratcheting response between room temperature and 200 °C. ► Isotropic cyclic hardening is dependent on the yield criterion used. ► Ratcheting induced hardening mostly affects the kinematic hardening component. ► Ratcheting induced hardening is related to the mean strain and the ratcheting rate. -- Abstract: With the purpose of analyzing the fatigue behavior under loading conditions relevant for the primary cooling circuit of a light water nuclear reactor, a set of uniaxial low cycle fatigue and strain-controlled ratcheting tests (also named ‘cyclic tension tests’) has been performed at room temperature and at 200 °C on specimens manufactured from two different batches of stainless steel grade 316L. The experiments have been repeated varying strain amplitude, cyclic ratcheting rate and ratcheting direction in order to investigate the influence on the cyclic deformation behavior. In strain-controlled ratcheting tests, the stress response is found to be a superposition of two hardening mechanisms: the first one due to the zero mean strain cycling and the second one linked with the monotonic drifting of mean plastic strain. An approach is proposed to distinguish the effect of each mechanism and the influence of the test parameters on the hardening mechanisms is discussed

Molecular biomarkers for sources of organic matter in lacustrine sediments in a subtropical lake in China.

Science.gov (United States)

Wang, Yan-Hua; Yang, Hao; Chen, Xia; Zhang, Ji-Xiang; Ou, Jie; Xie, Biao; Huang, Chang-Chun

2013-05-01

N-alkanes distributions and stable isotopic compositions (δ(13)C and δ(15)N) in the lacustrine sediments of Shijiu lake were measured to assess whether biological source information was recorded in the molecular biomarker. Results showed regular unimodal n-alkanes distribution in range of C16-C33 with strong predominance of odd-numbered n-alkanes, maximizing at C29. The δ(15)N for SON were uniformly low, ranging from -6.7‰ to 3.8‰ and C/N ratios ranged from 6.6 to 10.0, suggesting that most of organic matter was influenced by terrestrial characteristics of the watershed. The δ(13)C for C27 to C31n-alkanes and for SOC varied from -32.9‰ to -26.6‰ and -23.4‰ to -21.6‰, respectively, falling within the range of corresponding n-alkanes in leaves mainly from C3 land plants. The values of C/N, CPI, OEP, ACL and C27/C31 exhibit similar temporal changes with the primary production, showing enhanced eutrophication resulted from increased anthropogenic activities in Shijiu lake from 1852 to 2010. Copyright © 2013 Elsevier Ltd. All rights reserved.

The role of anti-cyclic citrullinated peptide antibodies in predicting rheumatoid arthritis.

Science.gov (United States)

Rexhepi, Sylejman; Rexhepi, Mjellma; Sahatçiu-Meka, Vjollca; Tafaj, Argjend; Izairi, Remzi; Rexhepi, Blerta

2011-01-01

The study presents the results of predicting role of anti-cyclic citrullinated peptide antibodies in rheumatoid arthritis, compared to rheumatoid factor. 32 patients with rheumatoid arthritis were identified from a retrospective chart review. The results of our study show that presence of the rheumatoid factor has less diagnostic and prognostic significance than the anti-cyclic citrullinated peptide, and suggests its superiority in predicting an erosive disease course.

Round Robin/collaborative programme [cyclic crack growth in low alloy steel

International Nuclear Information System (INIS)

Jones, R.L.; Hurst, P.; Scott, P.M.

1989-01-01

During the 10 years of its existence International Cooperative Group on Cyclic Crack Growth the (ICCGR) has undertaken five collaborative efforts related to cyclic crack growth and stress corrosion susceptibility in reactor pressure vessel steels. The initial collaborative effort, a data reduction exercise, identified and reconciled several important procedural differences and led to confidence that, given the same crack length versus cycles data, the Group members could all derive similar plots of da/dN versus δK. Subsequently, a low-R testing round robin highlighted the importance of a number of comparatively subtle aspects of the methods used for cyclic crack growth testing in water environments and led to confidence that the various laboratories could generate similar test data, given the same test material and a sufficiently precise and detailed test specification. The results of a high-R test programme support the conclusion that the state of the art of cyclic crack growth testing has now advanced to a point at which coordinated, multilaboratory test programmes are feasible and indeed, such a programme covering the influence of temperature is currently under way. The slow strain rate round robin has highlighted important test variables, notably the electrochemical potential, which must be carefully controlled in assessing the conditions under which pressure vessel steels may suffer from stress corrosion cracking. (author)

CHARACTERIZATION OF P2-PURINOCEPTOR MEDIATED CYCLIC-AMP FORMATION IN MOUSE C2C12 MYOTUBES

NARCIS (Netherlands)

HENNING, RH; DUIN, M; DENHERTOG, A; NELEMANS, A

1 The formation of adenosine 3':5'-cyclic monophosphate (cyclic AMP) and inositol(1,4,5)trisphosphate (Ins(1,4,5)P3), induced by ATP and other nucleotides was investigated in mouse C2Cl2 myotubes. 2 ATP (100 muM) and ATPgammaS (100 muM) caused a sustained increase in cyclic AMP content of the cells,

Some antarctic lacustrine sediments from northern Victoria Land investigation by Moessbauer spectroscopy, INNA and XRD

International Nuclear Information System (INIS)

Stievano, L.; Bertelle, M.; Leotta, G.; Calogero, S.; Constantinescu, S.; Oddone, M.

1999-01-01

Fifteen lacustrine sediments, sampled during the 1994-1995 Austral summer in Northern Victoria Land (Antarctica), were characterised by 57 Fe Moessbauer spectroscopy, instrumental neutron activation analysis and X-ray diffraction. These sediments are related to the intrusive rocks from Granite Harbour, to the metamorphic rocks of the Complex of Wilson Terrane and the volcanic rocks from Mc Murdo. The samples contain quartz, alkaline feldspars, plagioclases, amphiboles, biotite, chlorite and muscovite except for the sediments of volcanic origin that contain alkaline feldspars, plagioclases and pyroxenes. The paramagnetic components of the Moessbauer spectra were assigned mainly to the iron sides in biotites except for those displayed from the sediments of volcanic origin assigned mainly to pyroxenes. Moessbauer spectra at room temperature do not display magnetic ordering except for those of the sediments of volcanic origin containing bulk magnetite, hematite and goethite. Moessbauer spectra collected at the liquid helium temperature always exhibit magnetic ordering. This spectral difference has been attributed to the different dimensions of the iron oxide particles in the sediments. The scarce weathering involves a partial transformation of magnetite in hematite and goethite in the sediment of volcanic origin. In the remaining sediments a partial hydrolysis of biotite together with a partial oxidation of iron (II) retained in silicates is present. (authors)

Emission performance of lignin-derived cyclic oxygenates in a heavy-duty diesel engine

NARCIS (Netherlands)

Zhou, L.; Boot, M.D.; Luijten, C.C.M.; Leermakers, C.A.J.; Dam, N.J.; Goey, de L.P.H.

2012-01-01

In earlier research, a new class of bio-fuels, so-called cyclic oxygenates, was reported to have a favorable impact on the soot-NOx trade-off experience in diesel engines. In this paper, the soot-NOx trade-off is compared for two types of cyclic oxygenates. 2-phenyl ethanol has an aromatic and

Quantitative damage and detwinning analysis of nanotwinned copper foil under cyclic loading

International Nuclear Information System (INIS)

Yoo, Byung-Gil; Boles, Steven T.; Liu, Y.; Zhang, X.; Schwaiger, Ruth; Eberl, Christoph; Kraft, Oliver

2014-01-01

High-purity Cu samples containing parallel columns of highly aligned nanotwins with median spacing of ∼25 nm were subjected to tension–compression cyclic loading by a high-throughput cyclic testing method. The methodology utilizes gradients in surface strain amplitude of a vibrating cantilever: one along the beam axis, with decreasing strain from the fixed to the free end of the beam, and the other through the foil thickness with decreasing strain from the surface to the neutral axis. Systematic microstructural investigations indicate that nanotwins are not stable under cyclic loading and that the applied strain amplitude has a strong influence on the resulting twin structure. In the highly stressed regions the detwinning process produces a twin free microstructure, allowing for subsequent extrusion and crack formation, and introduces fatal defects into structural parts

Public administration and cyclical mechanisms socio-economic development

Directory of Open Access Journals (Sweden)

S. A. Kvitka

2016-03-01

Full Text Available The article discusses the cyclical mechanisms of socio-economic development as one of kinds of natural cycles. The author notes that in all cases the basis of the self-oscillations are cyclical. And they are only possible with the constant influx of three resources - energy, matter and information. On this basis, it is noted that the self-organization of coherent structures, regardless of their Genesis, is due to intrinsically contradictory unity of two interacting types of resource flows - energy, matter and information – And-stream forming system, and the In-flow that will disrupt her. The cycle of development of systems consists of two components: one that describes the development of a system with positive saturation, according to a logistic law (A>B; and another describing the development of the system with negative saturation.

Skew cyclic codes over F_q+uF_q+vF_q+uvF_q

Directory of Open Access Journals (Sweden)

Ting Yao

2015-09-01

Full Text Available In this paper, we study skew cyclic codes over the ring $R=F_q+uF_q+vF_q+uvF_q$, where $u^{2}=u,v^{2}=v,uv=vu$, $q=p^{m}$ and $p$ is an odd prime. We investigate the structural properties of skew cyclic codes over $R$ through a decomposition theorem. Furthermore, we give a formula for the number of skew cyclic codes of length $n$ over $R.$

The innate immune DNA sensor cGAS produces a noncanonical cyclic dinucleotide that activates human STING.

Science.gov (United States)

Diner, Elie J; Burdette, Dara L; Wilson, Stephen C; Monroe, Kathryn M; Kellenberger, Colleen A; Hyodo, Mamoru; Hayakawa, Yoshihiro; Hammond, Ming C; Vance, Russell E

2013-05-30

The presence of foreign DNA in the cytosol of mammalian cells elicits a potent antiviral interferon response. Recently, cytosolic DNA was proposed to induce the synthesis of cyclic GMP-AMP (cGAMP) upon binding to an enzyme called cGAMP synthase (cGAS). cGAMP activates an interferon response by binding to a downstream receptor called STING. Here, we identify natural variants of human STING (hSTING) that are poorly responsive to cGAMP yet, unexpectedly, are normally responsive to DNA and cGAS signaling. We explain this paradox by demonstrating that the cGAS product is actually a noncanonical cyclic dinucleotide, cyclic [G(2'-5')pA(3'-5')p], which contains a single 2'-5' phosphodiester bond. Cyclic [G(2'-5')pA(3'-5')p] potently activates diverse hSTING receptors and, therefore, may be a useful adjuvant or immunotherapeutic. Our results indicate that hSTING variants have evolved to distinguish conventional (3'-5') cyclic dinucleotides, known to be produced mainly by bacteria, from the noncanonical cyclic dinucleotide produced by mammalian cGAS. Copyright © 2013 The Authors. Published by Elsevier Inc. All rights reserved.

Experimental Investigation and FE Analysis on Constitutive Relationship of High Strength Aluminum Alloy under Cyclic Loading

Directory of Open Access Journals (Sweden)

Yuanqing Wang

2016-01-01

Full Text Available Experiments of 17 high strength aluminum alloy (7A04 specimens were conducted to investigate the constitutive relationship under cyclic loading. The monotonic behavior and hysteretic behavior were focused on and the fracture surface was observed by scanning electron microscope (SEM to investigate the microfailure modes. Based on Ramberg-Osgood model, stress-strain skeleton curves under cyclic loading were fitted. Parameters of combined hardening model including isotropic hardening and kinematic hardening were calibrated from test data according to Chaboche model. The cyclic tests were simulated in finite element software ABAQUS. The test results show that 7A04 aluminum alloy has obvious nonlinearity and ultra-high strength which is over 600 MPa, however, with relatively poor ductility. In the cyclic loading tests, 7A04 aluminum alloy showed cyclic hardening behavior and when the compressive strain was larger than 1%, the stiffness degradation and strength degradation occurred. The simulated curves derived by FE model fitted well with experimental curves which indicates that the parameters of this combined model can be used in accurate calculation of 7A04 high strength aluminum structures under cyclic loading.

The Innate Immune DNA Sensor cGAS Produces a Noncanonical Cyclic Dinucleotide that Activates Human STING

Directory of Open Access Journals (Sweden)

Elie J. Diner

2013-05-01

Full Text Available The presence of foreign DNA in the cytosol of mammalian cells elicits a potent antiviral interferon response. Recently, cytosolic DNA was proposed to induce the synthesis of cyclic GMP-AMP (cGAMP upon binding to an enzyme called cGAMP synthase (cGAS. cGAMP activates an interferon response by binding to a downstream receptor called STING. Here, we identify natural variants of human STING (hSTING that are poorly responsive to cGAMP yet, unexpectedly, are normally responsive to DNA and cGAS signaling. We explain this paradox by demonstrating that the cGAS product is actually a noncanonical cyclic dinucleotide, cyclic [G(2′-5′pA(3′-5′p], which contains a single 2′-5′ phosphodiester bond. Cyclic [G(2′-5′pA(3′-5′p] potently activates diverse hSTING receptors and, therefore, may be a useful adjuvant or immunotherapeutic. Our results indicate that hSTING variants have evolved to distinguish conventional (3′-5′ cyclic dinucleotides, known to be produced mainly by bacteria, from the noncanonical cyclic dinucleotide produced by mammalian cGAS.

Changes in mechanical properties following cyclic prestressing of martensitic steel containing vanadium carbide in presence of nondiffusible hydrogen

Energy Technology Data Exchange (ETDEWEB)

Kaneko, Mao; Doshida, Tomoki [Graduate School of Science and Technology, Sophia University, Tokyo 102-8554 (Japan); Takai, Kenichi, E-mail: takai@me.sophia.ac.jp [Department of Engineering and Applied Science, Sophia University, Tokyo 102-8554 (Japan)

2016-09-30

Changes in the states of nondiffusible hydrogen and mechanical properties after cyclic prestressing in the presence of only nondiffusible hydrogen were examined for martensitic steel containing vanadium carbide. The relationship between the change in the state of nondiffusible hydrogen and mechanical properties was also investigated. The hydrogen desorption profile in the high-temperature range decreased and that in the low-temperature range increased with increasing stress amplitude during cyclic prestressing in the presence of only nondiffusible hydrogen. Thus, the application of cyclic prestressing changed the state of hydrogen from a stable to an unstable one because of vacancies and their clusters. Hydrogen embrittlement susceptibility after cyclic prestressing increased with increasing stress amplitude and number of prestressing cycles in the presence of only nondiffusible hydrogen. This relationship indicates that hydrogen embrittlement susceptibility increased with the increasing amount of hydrogen detrapped from trap sites of nondiffusible hydrogen during cyclic prestressing. These results revealed that nondiffusible hydrogen easily detrapped from vanadium carbide due to the application of cyclic prestress and probably interacted with vacancies and their clusters, thus increasing hydrogen embrittlement susceptibility. The change of nondiffusible hydrogen to diffusible hydrogen and accumulation of vacancies and their clusters during cyclic prestressing are concluded to be the dominant factors in hydrogen embrittlement after the application of cyclic prestress.

Cyclic viscoelasticity and viscoplasticity of polypropylene/clay nanocomposites

DEFF Research Database (Denmark)

Drozdov, Aleksey; Christiansen, Jesper de Claville; Hog Lejre, Anne-Lise

2012-01-01

Observations are reported in tensile relaxation tests under stretching and retraction on poly-propylene/clay nanocomposites with various contents of filler. A two-phase constitutive model is developed in cyclic viscoelasticity and viscoplasticity of hybrid nanocomposites. Adjustable parameters in...

Synthesis and degradation of cyclic nucleotides in brain after a high dose of ionizing radiation

International Nuclear Information System (INIS)

Hunt, W.A.; Dalton, T.K.

1981-01-01

Previous data from our laboratory have indicated that a high dose of ionizing radiation can deplete the cyclic nucleotides guanosine 3',5'-cyclic monophosphate (cGMP) and adenosine 3',5'-cyclic monophosphate (cAMP) on several areas of the rat brain. cGMP is more sensitive to radiation than cAMP and does not recover for at least 24 h after irradiation. The response of cAMP is transient and recovery occurs within 4 h. The purpose of the present paper is to determine whether alternations in the activity of the synthetic and degradative enzymes that regulate cyclic nucleotide levels could account for the observed effects. Guanylate and adenylate cyclase and cGMP and cAMP phosphodiesterase activities were determined 10 min after irradiation with 10,000 rad of high-energy electrons. No alteration was detected under these experimental conditions. The data suggest that the reduction in cyclic nucleotides is not a direct effect on their metabolic enzymes and is probably secondary to some as yet-undefined action of radiation on the brain

A comparison of two reciprocating instruments using bending stress and cyclic fatigue tests

Directory of Open Access Journals (Sweden)

Pantaleo SCELZA

2015-01-01

Full Text Available The aim of this study was to comparatively evaluate the bending resistance at 45º, the static and dynamic cyclic fatigue life, and the fracture type of the WaveOne (Dentsply Maillefer, Ballaigues, Switzerland 25-08 and Reciproc (VDW, Munich, Germany 25-08 instruments. A total of 60 nickel-titanium (NiTi instruments (30 Reciproc and 30 WaveOne from three different lots, each of which was 25 mm in length, were tested. The bending resistance was evaluated through the results of a cantilever-bending test conducted using a universal testing machine. Static and dynamic cyclic fatigue testing was conducted using a custom-made device. For the static and dynamic tests, a cast Ni-Cr-Mo-Ti alloy metal block with an artificial canal measuring 1.77 mm in diameter and 20.00 mm in total length was used. A scanning electron microscope was used to determine the type of fracture. Statistical analyses were performed on the results. The WaveOne instrument was less flexible than the Reciproc (p < 0.05. The Reciproc instrument showed better resistance in the static and dynamic cyclic fatigue tests (p < 0.05. The transverse cross-section and geometry of the instruments were important factors in their resistance to bending and cyclic fracture. Both of the instruments showed ductile-type fracture characteristics. It can be concluded that the Reciproc 25-08 instrument was more resistant to static and dynamic cyclic fatigue than the WaveOne 25-08 instrument, while the WaveOne 25-08 instrument was less flexible. Bending and resistance to cyclic fracture were influenced by the instruments’ geometries and transverse cross-sections. Both of the instruments showed ductile-type fracture characteristics.

Cyclic approximation to stasis

Directory of Open Access Journals (Sweden)

Stewart D. Johnson

2009-06-01

Full Text Available Neighborhoods of points in $mathbb{R}^n$ where a positive linear combination of $C^1$ vector fields sum to zero contain, generically, cyclic trajectories that switch between the vector fields. Such points are called stasis points, and the approximating switching cycle can be chosen so that the timing of the switches exactly matches the positive linear weighting. In the case of two vector fields, the stasis points form one-dimensional $C^1$ manifolds containing nearby families of two-cycles. The generic case of two flows in $mathbb{R}^3$ can be diffeomorphed to a standard form with cubic curves as trajectories.

Stratigraphic architecture of a fluvial-lacustrine basin-fill succession at Desolation Canyon, Uinta Basin, Utah: Reference to Walthers’ Law and implications for the petroleum industry

Science.gov (United States)

Ford, Grace L.; David R. Pyles,; Dechesne, Marieke

2016-01-01

A continuous window into the fluvial-lacustrine basin-fill succession of the Uinta Basin is exposed along a 48-mile (77-kilometer) transect up the modern Green River from Three Fords to Sand Wash in Desolation Canyon, Utah. In ascending order the stratigraphic units are: 1) Flagstaff Limestone, 2) lower Wasatch member of the Wasatch Formation, 3) middle Wasatch member of the Wasatch Formation, 4) upper Wasatch member of the Wasatch Formation, 5) Uteland Butte member of the lower Green River Formation, 6) lower Green River Formation, 7) Renegade Tongue of the lower Green River Formation, 8) middle Green River Formation, and 9) the Mahogany oil shale zone marking the boundary between the middle and upper Green River Formations. This article uses regional field mapping, geologic maps, photographs, and descriptions of the stratigraphic unit including: 1) bounding surfaces, 2) key upward stratigraphic characteristics within the unit, and 3) longitudinal changes along the river transect. This information is used to create a north-south cross section through the basin-fill succession and a detailed geologic map of Desolation Canyon. The cross section documents stratigraphic relationships previously unreported and contrasts with earlier interpretations in two ways: 1) abrupt upward shifts in the stratigraphy documented herein, contrast with the gradual interfingering relationships proposed by Ryder et al., (1976) and Fouch et al., (1994), 2) we document fluvial deposits of the lower and middle Wasatch to be distinct and more widespread than previously recognized. In addition, we document that the Uteland Butte member of the lower Green River Formation was deposited in a lacustrine environment in Desolation Canyon.

Mechanical Stimulation of Adipose-Derived Stem Cells for Functional Tissue Engineering of the Musculoskeletal System via Cyclic Hydrostatic Pressure, Simulated Microgravity, and Cyclic Tensile Strain.

Science.gov (United States)

Nordberg, Rachel C; Bodle, Josie C; Loboa, Elizabeth G

2018-01-01

It is critical that human adipose stem cell (hASC) tissue-engineering therapies possess appropriate mechanical properties in order to restore function of the load bearing tissues of the musculoskeletal system. In an effort to elucidate the hASC response to mechanical stimulation and develop mechanically robust tissue engineered constructs, recent research has utilized a variety of mechanical loading paradigms including cyclic tensile strain, cyclic hydrostatic pressure, and mechanical unloading in simulated microgravity. This chapter describes methods for applying these mechanical stimuli to hASC to direct differentiation for functional tissue engineering of the musculoskeletal system.

Damage evolution analysis of coal samples under cyclic loading based on single-link cluster method

Science.gov (United States)

Zhang, Zhibo; Wang, Enyuan; Li, Nan; Li, Xuelong; Wang, Xiaoran; Li, Zhonghui

2018-05-01

In this paper, the acoustic emission (AE) response of coal samples under cyclic loading is measured. The results show that there is good positive relation between AE parameters and stress. The AE signal of coal samples under cyclic loading exhibits an obvious Kaiser Effect. The single-link cluster (SLC) method is applied to analyze the spatial evolution characteristics of AE events and the damage evolution process of coal samples. It is found that a subset scale of the SLC structure becomes smaller and smaller when the number of cyclic loading increases, and there is a negative linear relationship between the subset scale and the degree of damage. The spatial correlation length ξ of an SLC structure is calculated. The results show that ξ fluctuates around a certain value from the second cyclic loading process to the fifth cyclic loading process, but spatial correlation length ξ clearly increases in the sixth loading process. Based on the criterion of microcrack density, the coal sample failure process is the transformation from small-scale damage to large-scale damage, which is the reason for changes in the spatial correlation length. Through a systematic analysis, the SLC method is an effective method to research the damage evolution process of coal samples under cyclic loading, and will provide important reference values for studying coal bursts.

Cyclic deformation of NI/sub 3/(Al,Nb) single crystals at ambient and elevated temperatures

Energy Technology Data Exchange (ETDEWEB)

Bonda, N.R.

1985-01-01

Cyclic tests were performed on Ni/sub 3/(Al,Nb) (..gamma..' phase) single crystals by using a servo-hydraulic machine under fully reversed plastic strain control at a frequency of 0.1-0.2 Hz at room temperature, 400/sup 0/C and 700/sup 0/C. Since the monotonic behavior is orientation dependent, three orientations were studied. Asymmetry in tensile and compressive stresses was observed in the cyclic hardening curves of specimens tested at these temperatures and they were discussed with regard to the model suggested by Paider et al for monotonic behavior. The stress levels in the cyclic stress-strain curves (CSSC) at room temperature depended on orientation and cyclic history. No CSSCs were established at 400/sup 0/C and 700/sup 0/C. The deformation in cyclic tests at small plastic strain amplitudes was found to be different from that in monotonic tests in the microplastic regions in which the deformation is believed to be carried by a small density of edge dislocations. But in cyclic deformation, to and from motion of dislocations trap the edge dislocations into dipoles and therefore screw dislocations will be forced to participate in the deformation. Cracks on the surfaces of specimens tested at room temperature and 400/sup 0/C were found to be of stage I type, whereas at 700/sup 0/C, they were of stage II type.

On charge-3 cyclic monopoles

International Nuclear Information System (INIS)

Braden, H W; D'Avanzo, Antonella; Enolski, V Z

2011-01-01

We determine the spectral curve of charge-3 BPS su(2) monopoles with C 3 cyclic symmetry. The symmetry means that the genus 4 spectral curve covers a (Toda) spectral curve of genus 2. A well adapted homology basis is presented enabling the theta functions and monopole data of the genus 4 curve to be given in terms of genus 2 data. The Richelot correspondence, a generalization of the arithmetic mean, is used to solve for this genus 2 curve. Results of other approaches are compared

Cyclic graphs and Apery's theorem

International Nuclear Information System (INIS)

Sorokin, V N

2002-01-01

This is a survey of results about the behaviour of Hermite-Pade approximants for graphs of Markov functions, and a survey of interpolation problems leading to Apery's result about the irrationality of the value ζ(3) of the Riemann zeta function. The first example is given of a cyclic graph for which the Hermite-Pade problem leads to Apery's theorem. Explicit formulae for solutions are obtained, namely, Rodrigues' formulae and integral representations. The asymptotic behaviour of the approximants is studied, and recurrence formulae are found

Microstructure damage evolution associated with cyclic deformation for extruded AZ31B magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Xiong, Ying, E-mail: yxiong@zjut.edu.cn [Key Laboratory of Special Purpose Equipment and Advanced Processing Technology, Ministry of Education, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China)

2016-10-15

Fatigue damage evolution of extruded AZ31B magnesium (Mg) alloy is investigated under strain-controlled tension-compression loading along the extrusion direction at various strain amplitudes, and the different cyclic deformation behaviors are observed. At the strain amplitude of 2%, the tensile peak stress displays significant cyclic softening, whereas the compressive peak stress shows consistent cyclic hardening. At 1%, moderate cyclic hardening is observed at both the tensile peak and compressive peak stresses. At 0.5%, the tensile peak stress presents stable cyclic hardening, whereas the compressive peak stress almost keeps constant. The microstructure morphologies associated with the cyclic deformation are analyzed by scanning electronic microscope (SEM). The degree of deformation twins is evaluated by analyzing X-ray diffraction (XRD) using a normalized parameter λ. The results show the fatigue crack initiation modes and its propagation modes are dependent on the strain amplitude. At 2%, grain boundary (GB) cracking and triple joint cracking are detected after 1st loading cycle. At 1%, fatigue crack initiates at grain boundary (GB cracking), twin boundary (TB cracking) and triple joint of three neighboring grains. Both grain boundary induced (GB-induced) intergranular and persistent slip band induced (PSB-induced) transgranular propagation modes play an important role in the early-stage crack growth. At 0.5%, crack initiation modes are similar to that at 1%, but GB-induced intergranular propagation mode dominates the early-stage crack growth. The effects of the microstructure (texture, grain size and uniformity) on the fatigue damage behavior are discussed.

Cyclic behavior of Ta at low temperatures under low stresses and strain rates

International Nuclear Information System (INIS)

Stickler, C.; Knabl, W.; Stickler, R.; Weiss, B.

2001-01-01

The cyclic stress-strain response of recrystallized technically pure Ta was investigated in the stress range well below the technical flow stress, for temperatures between 173 K and 423 K, at loading rates between 0.042 Mpa/s and 4.2 Mpa/s with resulting plastic strains between -5 up to 1X10 -2 . Cyclic hardening-softening curves were recorded in multiple step tests. Cyclic stress strain curves exhibit straight portions associated with microplastic, transition range and macroplastic deformation mechanisms. The microstructure of the deformed specimens was characterized by SEM and TEM techniques which revealed typical dislocation arrangements related to plastic strain amplitudes and test temperatures. A mechanism of the microstrain deformation of Ta is proposed. (author)

Cyclic behavior of low rise concrete shear walls containing recycled coarse and fine aggregates

NARCIS (Netherlands)

Qiao, Qiyun; Cao, Wanlin; Qian, Zhiwei; Li, Xiangyu; Zhang, Wenwen; Liu, Wenchao

2017-01-01

In this study, the cyclic behaviors of low rise concrete shear walls using recycled coarse or fine aggregates were investigated. Eight low rise Recycled Aggregates Concrete (RAC) shear wall specimens were designed and tested under a cyclic loading. The following parameters were varied:

Fixed Point of Generalized Eventual Cyclic Gross in Fuzzy Norm Spaces for Contractive Mappings

Directory of Open Access Journals (Sweden)

S. A. M. Mohsenialhosseini

2015-01-01

Full Text Available We define generalized eventual cyclic gross contractive mapping in fuzzy norm spaces, which is a generalization of the eventual cyclic gross contractions. Also we prove the existence of a fixed point for this type of contractive mapping on fuzzy norm spaces.

Inotropic responses of the frog ventricle to adenosine triphosphate and related changes in endogenous cyclic nucleotides.

Science.gov (United States)

Flitney, F W; Singh, J

1980-07-01

1. A study has been made of a well documented but poorly understood response of the isolated frog ventricle to treatment with exogenous adenosine 5' triphosphate (ATP). Measurements of membrane potential, isometric twitch tension and levels of endogenous 3',5'-cyclic nucleotides have been made at various times during the ATP-induced response. 2. ATP elicits a characteristic triphasic response, which comprises an initial, abrupt increase in contractility, rising to a maximum within a few beats (first phase); followed by a period when the twitch amplitude falls, sometimes to below the control level (second phase); and superceded by a more slowly developing and longer-lasting increase in contractile force (third phase). The response is unaffected by atropine, propranolol or phentolamine. However, the prostaglandin synthetase inhibitor indomethacin depresses the first phase and entirely suppresses the third phase. 3. The inotropic effects of ATP are accompanied by changes in the shape of the action potential. These effects are dose-related. The duration of the action potential (D-30mV) and its positive overshoot (O) are increased during all phases of the response, for [ATP]o's up to 10(-5) M. However, at higher [ATP]o's, D-30mV and O ar both reduced during the second phase (but not the first or third phase), when isometric twitch tension is also depressed. The relationship between action potential duration and twitch tension (P) for different [ATP]o's is linear for all three phases of the response, but the slopes of the curves (delta P/delta D) are markedly different, indicating that the sensitivity of the contractile system to membrane depolarization is not constant, but varies continuously throughout the response. 4. ATP has a potent stimulatory effect on the metabolism of endogenous 3',5'-cyclic nucleotides. The time courses of the changes in adenosine 3','5-cyclic monophosphate (3',5'-cyclic AMP) and guanosine 3',5'-cyclic monophosphate (3',5'-cyclic GMP) are

The durability of waveguide fibers at cyclic change of loading, temperature and humidity

International Nuclear Information System (INIS)

Karimov, S.N.; Sultonov, U.; Shamsidinov, M.I.

1992-01-01

Present article is devoted to durability of waveguide fibers at cyclic change of loading, temperature and humidity. The mounting scheme and loading of sample is presented. The dependence of glass fiber durability on number of thermal cycles at various humidity rates was considered. The dependence of number of cycles on maximal loading at cyclic temperature change was studied.

High-resolution δ13C record of fossil wood and bulk organic matter from a deep Oligocene lacustrine succession, Bach Long Vi Island, Vietnam

Science.gov (United States)

Rizzi, M.; Schovsbo, N. H.; Fyhn, M. B. W.; Korte, C.

2017-12-01

We present a high-resolution stable isotope record based on bulk organic matter (δ13Corg) and fossil wood (δ13Cwood) originating from Oligocene deep lacustrine sediments cored on the Bach Long Vi Island, northern Gulf of Tonkin, offshore Vietnam. The sediments are exceptionally well preserved. They are thus excellently suited for a detailed stratigraphical analysis of the stable isotope record and as proxy for environmental and climatic changes within this period. The sediments were deposited in rapid subsiding, narrow and elongated fault-bound graben (Fyhn and Phach, 2015) and are represented by deep pelagic lacustrine organic-rich mud interrupted by numerous density-flow deposits (Hovikoski et al., 2016). The density-flow deposits contain abundant fragments of fossil wood. Therefore it was possible to obtain 262 coalified wood fragments together with 1063 bulk organic samples throughout the span of the core. This allowed to establish a high resolution stable C isotope record (δ13Corg and δ13Cwood). In addition 2464 handheld XRF determinations were carried out to further characterize the depositional environment (Rizzi et al., 2017). The organic carbon isotope trend from the 500 m core succession provides insight into the palaeoenvironmental changes of the lake during the Oligocene. Both, global and local factors control the δ13C variations. The aim of the study is to obtain pure global δ13Corg and δ13Cwood signals that would allow comparison of the studied sediments with coeval syn-rift successions in the South China Sea region and other parts of the world. [1] Fyhn and Phach (2015) Tectonics, 34(2): 290-312. [2] Hovikoski et al. (2016) Journal of Sedimentary Research, 86(8): 982-1007. [3] Rizzi et al. (2017) EGU General Assembly Abstract EGU 2017-17584.

Application of cyclic fluorocarbon/argon discharges to device patterning

International Nuclear Information System (INIS)

Metzler, Dominik; Uppireddi, Kishore; Bruce, Robert L.; Miyazoe, Hiroyuki; Zhu, Yu; Price, William; Sikorski, Ed S.; Engelmann, Sebastian U.; Joseph, Eric A.; Li, Chen; Oehrlein, Gottlieb S.

2016-01-01

With increasing demands on device patterning to achieve smaller critical dimensions and pitches for the 5 nm node and beyond, the need for atomic layer etching (ALE) is steadily increasing. In this work, a cyclic fluorocarbon/Ar plasma is successfully used for ALE patterning in a manufacturing scale reactor. Self-limited etching of silicon oxide is observed. The impact of various process parameters on the etch performance is established. The substrate temperature has been shown to play an especially significant role, with lower temperatures leading to higher selectivity and lower etch rates, but worse pattern fidelity. The cyclic ALE approach established with this work is shown to have great potential for small scale device patterning, showing self-limited etching, improved uniformity and resist mask performance

Application of cyclic fluorocarbon/argon discharges to device patterning

Energy Technology Data Exchange (ETDEWEB)

Metzler, Dominik, E-mail: dmetzler@umd.edu [IBM T. J. Watson Research Center, Yorktown Heights, New York 10598 and Department of Materials Science and Engineering, and Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, Maryland 20740 (United States); Uppireddi, Kishore; Bruce, Robert L.; Miyazoe, Hiroyuki; Zhu, Yu; Price, William; Sikorski, Ed S.; Engelmann, Sebastian U.; Joseph, Eric A. [IBM T. J. Watson Research Center, Yorktown Heights, New York 10598 (United States); Li, Chen [Department of Physics, and Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, Maryland 20740 (United States); Oehrlein, Gottlieb S. [Department of Materials Science and Engineering, and Institute for Research in Electronics and Applied Physics, University of Maryland, College Park, Maryland 20740 (United States)

2016-01-15

With increasing demands on device patterning to achieve smaller critical dimensions and pitches for the 5 nm node and beyond, the need for atomic layer etching (ALE) is steadily increasing. In this work, a cyclic fluorocarbon/Ar plasma is successfully used for ALE patterning in a manufacturing scale reactor. Self-limited etching of silicon oxide is observed. The impact of various process parameters on the etch performance is established. The substrate temperature has been shown to play an especially significant role, with lower temperatures leading to higher selectivity and lower etch rates, but worse pattern fidelity. The cyclic ALE approach established with this work is shown to have great potential for small scale device patterning, showing self-limited etching, improved uniformity and resist mask performance.

Cyclic mechanical fatigue in ceramic-ceramic composites: an update

International Nuclear Information System (INIS)

Lewis, D. III

1983-01-01

Attention is given to cyclic mechanical fatigue effects in a number of ceramics and ceramic composites, including several monolithic ceramics in which significant residual stresses should be present as a result of thermal expansion mismatches and anisotropy. Fatigue is also noted in several BN-containing ceramic matrix-particulate composites and in SiC fiber-ceramic matrix composites. These results suggest that fatigue testing is imperative for ceramics and ceramic composites that are to be used in applications subject to cyclic loading. Fatigue process models are proposed which provide a rationale for fatigue effect observations, but do not as yet provide quantitative results. Fiber composite fatigue damage models indicate that design stresses in these materials may have to be maintained below the level at which fiber pullout occurs

Wind influence on the course of sedimentation processes of the laminated lacustrine sediments of Lake Czechowskie

Science.gov (United States)

Wiśniewska, Daria; Kramkowski, Mateusz; Tyszkowski, Sebastian

2016-04-01

The studies of the laminated lacustrine sediments play a very important role in the analysis of climate change. They provide valuable information related to the response of the ecosystem to changes in the environment. The condition for the development of the annual lamination is calm sedimentation, which can be compromised by the movement of water caused by waving. The depth to which this movement affects depends on the shape of the lake basin as well as the velocity and direction of the wind. During the study of sedimentary processes of laminated deposits in Lake Czechowskie (Tuchola Forest, North Poland, 53°52'N, 18°14' E, 108 m asl), the following question arose: How strong was the influence of the wind on the processes of lacustrine sedimentation? The key in getting the answers was the use of GIS techniques. Lake Czechowskie has an area of 76.6 hectares; it has two deeps separated by a threshold: a deeper one of 33 m (maximum depth of the basin) in the central-eastern part, and a shallower of 13 m in the western part. The speed of movement of water that is able to move sediment from the bottom of the lake, called the orbital wave velocity, is the basis for the designation of areas where re-suspension takes place. To calculate the wave parameters, the process of mixing, as well as the designation of re-suspension zones, the tool-script Wave Model (Rohweder et al. 2008) in the program ArsGIS 10.1 was used. The input data were wind direction and velocity from the meteorological station of Wirty about 15 km away, bathymetric data from acoustic profiling, and the Maximum Orbital Wave Velocity. The elements taken into account include maximum wind velocity of the multi-year 1996-2013, with particular emphasis on hurricanes Ksawery (December 2013) and Yoda (November 2011), during which wind velocity exceeded 120 km/h. In addition, maximum wind velocity ever recorded in the Polish Lowlands was considered. On the basis of the modelling, the authors delimited the areas

An improved Armstrong-Frederick-Type Plasticity Model for Stable Cyclic Stress-Strain Responses Considering Nonproportional Hardening

Science.gov (United States)

Li, Jing; Zhang, Zhong-ping; Li, Chun-wang

2018-03-01

This paper modified an Armstrong-Frederick-type plasticity model for investigating the stable cyclic deformation behavior of metallic materials with different sensitivity to nonproportional loadings. In the modified model, the nonproportionality factor and nonproportional cyclic hardening coefficient coupled with the Jiang-Sehitoglu incremental plasticity model were used to estimate the stable stress-strain responses of the two materials (1045HR steel and 304 stainless steel) under various tension-torsion strain paths. A new equation was proposed to calculate the nonproportionality factor on the basis of the minimum normal strain range. Procedures to determine the minimum normal strain range were presented for general multiaxial loadings. Then, the modified model requires only the cyclic strain hardening exponent and cyclic strength coefficient to determine the material constants. It is convenient for predicting the stable stress-strain responses of materials in engineering application. Comparisons showed that the modified model can reflect the effect of nonproportional cyclic hardening well.

Bond-Slip Relationship for CFRP Sheets Externally Bonded to Concrete under Cyclic Loading.

Science.gov (United States)

Li, Ke; Cao, Shuangyin; Yang, Yue; Zhu, Juntao

2018-02-26

The objective of this paper was to explore the bond-slip relationship between carbon fiber-reinforced polymer (CFRP) sheets and concrete under cyclic loading through experimental and analytical approaches. Modified beam tests were performed in order to gain insight into the bond-slip relationship under static and cyclic loading. The test variables are the CFRP-to-concrete width ratio, and the bond length of the CFRP sheets. An analysis of the test results in this paper and existing test results indicated that the slope of the ascending segment of the bond-slip curve decreased with an increase in the number of load cycles, but the slip corresponding to the maximum shear stress was almost invariable as the number of load cycles increased. In addition, the rate of reduction in the slope of the ascending range of the bond-slip curve during cyclic loading decreased as the concrete strength increased, and increased as the load level or CFRP-to-concrete width ratio enhanced. However, these were not affected by variations in bond length if the residual bond length was longer than the effective bond length. A bilinear bond-slip model for CFRP sheets that are externally bonded to concrete under cyclic loading, which considered the effects of the cyclic load level, concrete strength, and CFRP-to-concrete ratio, was developed based on the existing static bond-slip model. The accuracy of this proposed model was verified by a comparison between this proposed model and test results.

Bond–Slip Relationship for CFRP Sheets Externally Bonded to Concrete under Cyclic Loading

Science.gov (United States)

Li, Ke; Cao, Shuangyin; Yang, Yue; Zhu, Juntao

2018-01-01

The objective of this paper was to explore the bond–slip relationship between carbon fiber-reinforced polymer (CFRP) sheets and concrete under cyclic loading through experimental and analytical approaches. Modified beam tests were performed in order to gain insight into the bond–slip relationship under static and cyclic loading. The test variables are the CFRP-to-concrete width ratio, and the bond length of the CFRP sheets. An analysis of the test results in this paper and existing test results indicated that the slope of the ascending segment of the bond–slip curve decreased with an increase in the number of load cycles, but the slip corresponding to the maximum shear stress was almost invariable as the number of load cycles increased. In addition, the rate of reduction in the slope of the ascending range of the bond–slip curve during cyclic loading decreased as the concrete strength increased, and increased as the load level or CFRP-to-concrete width ratio enhanced. However, these were not affected by variations in bond length if the residual bond length was longer than the effective bond length. A bilinear bond–slip model for CFRP sheets that are externally bonded to concrete under cyclic loading, which considered the effects of the cyclic load level, concrete strength, and CFRP-to-concrete ratio, was developed based on the existing static bond–slip model. The accuracy of this proposed model was verified by a comparison between this proposed model and test results. PMID:29495383

Undrained Cyclic Behaviour of Dense Frederikshavn Sand

DEFF Research Database (Denmark)

Nielsen, Søren Kjær; Ibsen, Lars Bo; Sørensen, Kris Wessel

2013-01-01

A modified contour diagram is created for the Frederikshavn Sand in the undrained case for a relative density of ID = 80 %. It can be used to estimate the number of cycles to failure for a given combination of pore pressure, average and cyclic load ratio. The diagram is based on a series of undra...

Instantaneous angular speed monitoring of gearboxes under non-cyclic stationary load conditions

Science.gov (United States)

Stander, C. J.; Heyns, P. S.

2005-07-01

Recent developments in the condition monitoring and asset management market have led to the commercialisation of online vibration-monitoring systems. These systems are primarily utilised to monitor large mineral mining equipment such as draglines, continuous miners and hydraulic shovels. Online monitoring systems make diagnostic information continuously available for asset management, production outsourcing and maintenance alliances with equipment manufacturers. However, most online vibration-monitoring systems are based on conventional vibration-monitoring technologies, which are prone to giving false equipment deterioration warnings on gears that operate under fluctuating load conditions. A simplified mathematical model of a gear system was developed to illustrate the feasibility of monitoring the instantaneous angular speed (IAS) as a means of monitoring the condition of gears that are subjected to fluctuating load conditions. A distinction is made between cyclic stationary load modulation and non-cyclic stationary load modulation. It is shown that rotation domain averaging will suppress the modulation caused by non-cyclic stationary load conditions but will not suppress the modulation caused by cyclic stationary load conditions. An experimental investigation on a test rig indicated that the IAS of a gear shaft could be monitored with a conventional shaft encoder to indicate a deteriorating gear fault condition.

Fatigue Performance of SFPSC under Hot-Wet Environments and Cyclic Bending Loads

Directory of Open Access Journals (Sweden)

Shanshan Luo

2018-01-01

Full Text Available A new structural material named “steel fiber polymer structural concrete (SFPSC” with features of both high strength and high toughness was developed by this research group and applied to the bridge superstructures in the hot-wet environments. In order to investigate the fatigue performance and durability of SFPSC under hot-wet environments, the environment and fatigue load uncoupling method and the coupling action of environment and fatigue load were used or developed. Three-point bending fatigue experiments with uncoupling action of environments and cyclic loads were carried out for SFPSC specimens which were pretreated under hot-wet environments, and the experiments with the coupling action of environments and cyclic loads for SFPSC specimens were carried out under hot-wet environments. Then, the effects of hot-wet environments and the experimental methods on the fatigue mechanism of SFPSC material were discussed, and the environmental fatigue equations of SFPSC material under coupling and uncoupling action of hot-wet environments and cyclic bending loads were established. The research results show that the fatigue limits of SFPSC under the coupling action of the environments and cyclic loads were lower about 15%. The proposed fatigue equations could be used to estimate the fatigue lives and fatigue limits of SFPSC material.

Plasma concentrations of the cyclic nucleotides, adenosine 3',5'-monophosphate and guanosine 3'.5'-monophosphate, in healthy adults treated with theophylline

DEFF Research Database (Denmark)

Fenger, M; Eriksen, P B; Andersen, O

1982-01-01

Plasma concentrations of cyclic adenosine monophosphate and cyclic guanosine monophosphate were measured in 10 health adults before, during and after periods of theophylline administration. Cyclic adenosine monophosphate concentrations did not change significantly, but cyclic guanosine monophosph...

Gαs regulates Glucagon-Like Peptide 1 Receptor-mediated cyclic AMP generation at Rab5 endosomal compartment.

Science.gov (United States)

Girada, Shravan Babu; Kuna, Ramya S; Bele, Shilpak; Zhu, Zhimeng; Chakravarthi, N R; DiMarchi, Richard D; Mitra, Prasenjit

2017-10-01

Upon activation, G protein coupled receptors (GPCRs) associate with heterotrimeric G proteins at the plasma membrane to initiate second messenger signaling. Subsequently, the activated receptor experiences desensitization, internalization, and recycling back to the plasma membrane, or it undergoes lysosomal degradation. Recent reports highlight specific cases of persistent cyclic AMP generation by internalized GPCRs, although the functional significance and mechanistic details remain to be defined. Cyclic AMP generation from internalized Glucagon-Like Peptide-1 Receptor (GLP-1R) has previously been reported from our laboratory. This study aimed at deciphering the molecular mechanism by which internalized GLP-R supports sustained cyclic AMP generation upon receptor activation in pancreatic beta cells. We studied the time course of cyclic AMP generation following GLP-1R activation with particular emphasis on defining the location where cyclic AMP is generated. Detection involved a novel GLP-1 conjugate coupled with immunofluorescence using specific endosomal markers. Finally, we employed co-immunoprecipitation as well as immunofluorescence to assess the protein-protein interactions that regulate GLP-1R mediated cyclic AMP generation at endosomes. Our data reveal that prolonged association of G protein α subunit Gαs with activated GLP-1R contributed to sustained cyclic AMP generation at Rab 5 endosomal compartment. The findings provide the mechanism of endosomal cyclic AMP generation following GLP-1R activation. We identified the specific compartment that serves as an organizing center to generate endosomal cyclic AMP by internalized activated receptor complex. Copyright © 2017 The Authors. Published by Elsevier GmbH.. All rights reserved.

Performance of 3Y-TZP bioceramics under cyclic fatigue loading

Directory of Open Access Journals (Sweden)

Renato Chaves Souza

2008-03-01

Full Text Available In this work, the static mechanical properties and cyclic fatigue life of 3 mol. (% Y2O3-stabilized tetragonal zirconia polycrystalline (3Y-TZP ceramics were investigated. Pre-sintered samples were sintered in air at 1600 °C for 120 minutes, and characterized by X ray diffraction and scanning electronic microscopy. Hardness and fracture toughness were determined by Vicker's indentation method, and Modulus of Rupture was determined by four-point bending testing. Fully dense sintered samples, near to 100% of theoretical density, presented hardness, fracture toughness and bending strength of 13.5 GPa, 8.2 MPa.m½ and 880 MPa, respectively. The cyclic fatigue tests were also realized using four-point bending testing, within a frequency of 25 Hz and stress ratio R of 0.1. The increasing of load stress lead to decreasing of the number of cycles and the run-out specimens number. The tetragonal-monoclinic (t-m ZrO2-transformation observed by X ray diffraction contributes to the increasing of the fatigue life. The 3Y-TZP samples clearly presents a range of loading conditions where cyclic fatigue can be detected.

EFFECTIVENESS OF PNF STRETCHING AND CYCLIC STRETCHING OF CALF TIGHTNESS ON COLLEGE GOING GIRLS

Directory of Open Access Journals (Sweden)

Ashlesha Sirari

2015-06-01

Full Text Available Background: Flexibility helps with injury prevention, the reduction of soreness following a workout, and a general sense of well-being. There are different stretching techniques and protocols for improvements in calf extensibility and flexibility. The purpose of the study was to investigate the effectiveness of two techniques i.e. CYCLIC and PNF stretching which improves calf flexibility. This study was done to find the effectiveness of calf Cyclic and PNF stretching technique to improve calf flexibility. Methods: 30 subjects with age group 21-22 years were randomly allocated to 2 groups equally. Group 1(n=15 were given CYCLIC and group 2(n=15 were given PNF stretching technique. Plantar flexion was used to measure the calf tightness which was done before and after the treatment. Treatment was given for 7 days and on the 7th day the calf tightness was again measured. Results: The mean difference of the CYCLIC is 4.6 and mean difference of PNF is 4.7 which indicate that CYCLIC and PNF both are effective to improve calf flexibility but PNF is more effective than CYCLIC to improve calf flexibility. Conclusion: The neurophysiological basis of PNF, stating that the excitatory efficient of the neuromuscular spindle or the inhibitory afferent of the Golgi tendon organ (GTO or both are responsible for the effects. During PNF stretch and isometric contraction of stretched agonists for extended period may cause activation of its neuromuscular spindle. The increase in tension created during the isometric contraction of the pre – lengthened agonist contracts concentrically. Both the fascia & the spindle of the agonist adjust to the nearly lengthened position. These impulses travel via causing post synaptic inhibition of the motor neuron to agonist increasing the tension from the GTO. These impulses can override the impulses coming from the neuromuscular spindles arousing the muscle to reflexly resist to the change in length, thus helping in lengthening

Regulation of thrombomodulin expression and release in human aortic endothelial cells by cyclic strain.

Directory of Open Access Journals (Sweden)

Fiona A Martin

Full Text Available Thrombomodulin (TM, an integral membrane glycoprotein expressed on the lumenal surface of vascular endothelial cells, promotes anti-coagulant and anti-inflammatory properties. Release of functional TM from the endothelium surface into plasma has also been reported. Much is still unknown however about how endothelial TM is regulated by physiologic hemodynamic forces (and particularly cyclic strain intrinsic to endothelial-mediated vascular homeostasis.This study employed human aortic endothelial cells (HAECs to investigate the effects of equibiaxial cyclic strain (7.5%, 60 cycles/min, 24 hrs, and to a lesser extent, laminar shear stress (10 dynes/cm2, 24 hrs, on TM expression and release. Time-, dose- and frequency-dependency studies were performed.Our initial studies demonstrated that cyclic strain strongly downregulated TM expression in a p38- and receptor tyrosine kinase-dependent manner. This was in contrast to the upregulatory effect of shear stress. Moreover, both forces significantly upregulated TM release over a 48 hr period. With continuing focus on the cyclic strain-induced TM release, we noted both dose (0-7.5% and frequency (0.5-2.0 Hz dependency, with no attenuation of strain-induced TM release observed following inhibition of MAP kinases (p38, ERK-1/2, receptor tyrosine kinase, or eNOS. The concerted impact of cyclic strain and inflammatory mediators on TM release from HAECs was also investigated. In this respect, both TNFα (100 ng/ml and ox-LDL (10-50 µg/ml appeared to potentiate strain-induced TM release. Finally, inhibition of neither MMPs (GM6001 nor rhomboids (3,4-dichloroisocoumarin had any effect on strain-induced TM release. However, significantly elevated levels (2.1 fold of TM were observed in isolated microparticle fractions following 7.5% strain for 24 hrs.A preliminary in vitro investigation into the effects of cyclic strain on TM in HAECs is presented. Physiologic cyclic strain was observed to downregulate TM

In-situ investigations of structural changes during cyclic loading by high resolution reciprocal space mapping

DEFF Research Database (Denmark)

Diederichs, Annika M.; Thiel, Felix; Lienert, Ulrich

2017-01-01

dislocation structures can be identified using advanced electron microscopy and synchrotron techniques. A detailed characterization of the microstructure during cyclic loading by in-situ monitoring the internal structure within individual grains with high energy x-rays can help to understand and predict...... the materials behavior during cyclic deformation and to improve the material design. While monitoring macroscopic stress and strain during cyclic loading, reciprocal space maps of diffraction peaks from single grains are obtained with high resolution. High Resolution Reciprocal Space Mapping was applied...

On numerically pluricanonical cyclic coverings

International Nuclear Information System (INIS)

Kulikov, V S; Kharlamov, V M

2014-01-01

We investigate some properties of cyclic coverings f:Y→X (where X is a complex surface of general type) branched along smooth curves B⊂X that are numerically equivalent to a multiple of the canonical class of X. Our main results concern coverings of surfaces of general type with p g =0 and Miyaoka-Yau surfaces. In particular, such coverings provide new examples of multi-component moduli spaces of surfaces with given Chern numbers and new examples of surfaces that are not deformation equivalent to their complex conjugates

Progressive buckling under both constant axial load and cyclic distortion

International Nuclear Information System (INIS)

Clement, G.; Acker, D.; Lebey, J.

1988-09-01

Thin structures submitted to compressive loads must be carefully designed to avoid any risk of ruin by buckling. The aim of this paper is, first, to evidence that the critical buckling load may be notably lowered when cyclic strains are added to the compressive load and, secondly, to propose a practical rule of prevention against the ruin due to the progressive buckling phenomenon. This rule is validated by the results of numerous tests related to the entire range of modes of buckling (i.e. from fully plastic to fully elastic). Practical cases of interest for its use could mainly be those where cyclic thermal stresses are involved

New cyclic peptides with osteoblastic proliferative activity from Dianthus superbus.

Science.gov (United States)

Tong, Yun; Luo, Jian-Guang; Wang, Rui; Wang, Xiao-Bing; Kong, Ling-Yi

2012-03-01

Two new cyclic peptides, dianthins G-H (1 and 2), together with the known dianthin E (3), were isolated from the traditional Chinese medicinal plant Dianthus superbus. The sequences of cyclic peptides 1 and 2 were elucidated as cyclo (-Gly(1)-Pro(2)-Leu(3)-Thr(4)-Leu(5)-Phe(6)-) and cyclo (-Gly(1)-Pro(2)-Val(3)-Thr(4)-Ile(5)-Phe(6)-), on the basis of ESI tandem mass fragmentation analysis, extensive 2D NMR methods and X-ray diffraction. The isolated three compounds all increase proliferation of MC3T3-E1 cells in vitro using MTT method. Copyright © 2012 Elsevier Ltd. All rights reserved.

Parameters Determination of Yoshida Uemori Model Through Optimization Process of Cyclic Tension-Compression Test and V-Bending Springback

Directory of Open Access Journals (Sweden)

Serkan Toros

Full Text Available Abstract In recent years, the studies on the enhancement of the prediction capability of the sheet metal forming simulations have increased remarkably. Among the used models in the finite element simulations, the yield criteria and hardening models have a great importance for the prediction of the formability and springback. The required model parameters are determined by using the several test results, i.e. tensile, compression, biaxial stretching tests (bulge test and cyclic tests (tension-compression. In this study, the Yoshida-Uemori (combined isotropic and kinematic hardening model is used to determine the performance of the springback prediction. The model parameters are determined by the optimization processes of the cyclic test by finite element simulations. However, in the study besides the cyclic tests, the model parameters are also evaluated by the optimization process of both cyclic and V-die bending simulations. The springback angle predictions with the model parameters obtained by the optimization of both cyclic and V-die bending simulations are found to mimic the experimental results in a better way than those obtained from only cyclic tests. However, the cyclic simulation results are found to be close enough to the experimental results.

Kinetic analysis of the reactivity of aliphatic cyclic alcohols and carboxylic acids in the T-for-H exchange reaction

International Nuclear Information System (INIS)

Tamura, Kiyoshi; Imaizumi, Hiroshi; Kano, Naoki

2007-01-01

In order to quantitatively evaluate the influence of tritium ( 3 He or T) on various functional groups in environment, the hydrogen isotope exchange reaction (T-for-H exchange reaction) between tritium-labeled poly-(vinyl alcohol) and each aliphatic cyclic alcohol (or carboxylic acid) has been dynamically observed in the range of 50 to 90degC. Consequently, the activities of the aliphatic cyclic alcohol and carboxylic acid increased with increasing reaction time. Applying in A''-McKay plot method to the observed data, the rate constants (k) for these materials were obtained. Using the k, the relation between the number of carbon atoms in the ring in each alcohol and the reactivity of the alcohol was quantitatively compared. Then, to clarify the effect of relative atomic charge of O atom (connected with the H atom in the hydroxy (or carboxy) group in the material) on the reactivity of the material, the MOPAC method was used. From both the above-mentioned and the obtained previously, the following nine items were found as to aliphatic cyclic alcohols (and carboxylic acids) in the T-for-H exchange reaction. (1) The reactivity of aliphatic cyclic alcohols (and carboxylic acids) depends on the temperature. (2) The reactivity of the cyclic materials decreases with increasing number of carbon atoms in the ring. (3) The reactivity of the aliphatic cyclic carboxylic acid seems to be smaller than that of aliphatic cyclic alcohol, and be larger than that of aliphatic cyclic amine. (4) For aliphatic cyclic alcohols, correlation exists between k and relative atomic charges of O atom obtained by the MOPAC method, but the tendency for aliphatic cyclic carboxylic acid is not clear. (5) As to having the same number of carbon atoms in each ring, the reactivity of the aliphatic cyclic carboxylic acid including the side chain is smaller than of the aliphatic cyclic carboxylic acid including no side chain. (6) The reactivity of aliphatic cyclic carboxylic acid is larger than that of

Synthesis of Chiral Cyclic Carbonates via Kinetic Resolution of Racemic Epoxides and Carbon Dioxide

Directory of Open Access Journals (Sweden)

Xiao Wu

2016-01-01

Full Text Available The catalytic synthesis of cyclic carbonates using carbon dioxide as a C1-building block is a highly active area of research. Here, we review the catalytic production of enantiomerically enriched cyclic carbonates via kinetic resolution of racemic epoxides catalysed by metal-containing catalyst systems.

Physical Modelling of Bucket Foundation Under Long-Term Cyclic Lateral Loading

DEFF Research Database (Denmark)

Foglia, Aligi; Ibsen, Lars Bo; Andersen, Lars Vabbersgaard

2012-01-01

Offshore wind farms are a promising renewable energy source. The monopod bucket foundation has the potential to become a reliable and cost-effective concept for offshore wind turbines. The bucket foundation must be designed by accounting for the cyclic loading which might endanger the turbine...... functioning. In this article a 1g physical model of bucket foundation under horizontal and moment cyclic loading is described. A testing program including four tests was carried out. Every test was conducted for at least 30000 cycles, each with different loading features. The capability of the model...

Deformation Mechanisms of Offshore Monopile Foundations Accounting for Cyclic Mobility Effects

DEFF Research Database (Denmark)

Barari, Amin; Bagheri, Mohsen; Rouainia, Mohamed

2017-01-01

Highlights •There has been a huge surge in the construction of marine facilities (e.g., wind turbines) in Europe. •This paper presents some new frameworks for design strategy based on performance measures for cyclic horizontally loaded monopile foundations. •A three-dimensional finite element model...... was developed to investigate the behavior of large-diameter piles. •This model accounts for nonlinear dynamic interactions in offshore platforms under harsh combined moment and horizontal environmental loads. •Magnitude of cyclic loads was found to cause a linear increase in the accumulated rotation....

Literature review on cyclic lateral loading effects of mono-bucket foundations

DEFF Research Database (Denmark)

Kapitanov, Lachezar Rosenov; Duroska, Peter; Quirante, Cesar Antonio Garcia

2016-01-01

and consequently cost-effectiveness compared to other common solutions. The long-term cyclic loading can cause degradation of soil-bucket system stiffness, which yields into accumulated and permanent deformations. Despite of the advantages, there is no standard procedure to design the foundation especially...... calculation is highly demanded at the different design phases. The intention of the current study is to present, review and summarize the existing techniques to assess the effect of cyclic loading on Mono-Bucket foundations while emphasizing the advantage and disadvantage of each of them. Additionally...

Fundamental principles of the cyclic behaviour and the fatigue damage for metallic materials

International Nuclear Information System (INIS)

Vogt, J.B.

2001-01-01

The aim of this paper is a pedagogic presentation of the basic concepts concerning the cyclic behaviour and the fatigue damage of metallic materials in order to offer a better understand of mechanisms. The following aspects are taking into account: the fatigue fracture, the cyclic accommodation, the dislocations structures, the surface and bulk cracks and the influence of the medium. (A.L.B.)

Cyclic Loading of Growing Tissue in a Bioreactor: Mathematical Model and Asymptotic Analysis

KAUST Repository

Pohlmeyer, J. V.

2013-10-24

A simplified 2D mathematical model for tissue growth within a cyclically-loaded tissue engineering scaffold is presented and analyzed. Such cyclic loading has the potential to improve yield and functionality of tissue such as bone and cartilage when grown on a scaffold within a perfusion bioreactor. The cyclic compression affects the flow of the perfused nutrient, leading to flow properties that are inherently unsteady, though periodic, on a timescale short compared with that of tissue proliferation. A two-timescale analysis based on these well-separated timescales is exploited to derive a closed model for the tissue growth on the long timescale of proliferation. Some sample numerical results are given for the final model, and discussed. © 2013 Society for Mathematical Biology.

Laboratory experiments of bucket foundations under cyclic loading

DEFF Research Database (Denmark)

Foglia, Aligi; Ibsen, Lars Bo

This report collects information on the experimental campaign concerning bucket foundations under lateral cyclic loading conducted by the authors between 2011 and 2014. The report includes a step by step manual on the test procedures and a number of information and graphs for each experiment...

Structure and stability of spiro-cyclic water clusters

Indian Academy of Sciences (India)

Administrator

Abstract. The structure and stability of spiro-cyclic water clusters containing up to 32 water molecules have been ... due to its importance in various real life systems. 1–8. High level ... It is well-known from the crystal structure data- base that the ...

Are international fund flows pro- or counter-cyclical?

NARCIS (Netherlands)

Li, Suxiao; de Haan, Jakob; Scholtens, Bert; Yang, Haizhen

2015-01-01

We investigate whether international fund flows are pro-or counter-cyclical by employing a concordance index. International fund flows are investments in bond and equity markets by institutional investors, such as mutual funds, exchange traded funds, closed-end funds and hedge funds. We find that

Twinning behavior in the Ti-5at.% Al single crystals during cyclic loading along [0001

International Nuclear Information System (INIS)

Xiao Lin

2005-01-01

Cyclic deformation behavior of Ti-5at.% Al single crystals subjected to pull-push cyclic load along [0001] crystallographic orientation was studied. A higher cyclic stress response was displayed in the Ti-5Al single crystal oriented for [0001] than that oriented for single prism slip. Optical microscopy and transmission electron microscopy examinations show that twinning is a dominant plastic deformation mode in the single crystals during cycling. Trace analysis of prepolished surfaces was used to identify the twin systems primarily responsible for deformation. The major twin type observed was {101-bar 2}, {112-bar 2}, {101-bar 1} and {112-bar 1}. slip was observed in the neighboring region of twins in the fatigued specimens. The activation of multiple twinning systems contributed to the higher cyclic saturation stress in Ti-5Al single crystals oriented for [0001

Can the universe fragment into many independent causal patches at turnaround in cyclic cosmology?

International Nuclear Information System (INIS)

Zhang, Xin

2009-01-01

Infinitely cyclic cosmology is often frustrated by the second law of thermodynamics which dictates that the entropy increases from cycle to cycle so that extrapolation into the past will lead back to an initial singularity. It has been argued in the literature that the entropy problem can be resolved in a particular cyclic universe model through a deflation mechanism (i.e., the universe fragments into an astronomically large number of disconnected causal patches at the turnaround). We point out that in this cyclic model the Hubble distance will become infinity at the turnaround; thus the deflation scenario does not seem to be valid. (orig.)

Modification of radiation-induced division delay by caffeine analogues and dibutyryl cyclic AMP

Energy Technology Data Exchange (ETDEWEB)

Kimler, B.F.; Leeper, D.B.; Snyder, M.H.; Rowley, R.; Schneiderman, M.H. (Thomas Jefferson Univ., Philadelphia, PA (USA). Hospital)

1982-01-01

The mitotic selection procedure for cell cycle analysis was utilized to investigate the concentration-dependent modification of x-radiation-induced division delay in Chinese hamster ovary (CHO) cells by methyl xanthines (caffeine, theophylline, and theobromine) and by dibutyryl cyclic AMP. The methyl xanthines (concentrations from 0.5 to 1000 ..mu..g/ml) all reduced radiation-induced division delay with the effect being linear between approximately 100 and 1000 ..mu..g/ml. After doses of 100-300 rad, delay was reduced by 75, 94 or 83 per cent at 1000 ..mu..g/ml for each drug, respectively. However, the addition of dibutyryl cyclic AMP had an opposite effect: radiation-induced delay was increased by the concentration range of 0.3 to 300 ..mu..g/ml. These results indicate that in mammalian cells the control of cell cycle progression and the modification of radiation-induced division delay are not simply related to intracellular levels of cyclic AMP. Rather, there appear to be at least two competing mechanisms which are differentially affected by caffeine analogues or by direct addition of dibutyryl cyclic AMP. The direct effect of caffeine and the methyl xanthines on membrane calcium permeability is considered.

Modification of radiation-induced division delay by caffeine analogues and dibutyryl cyclic AMP

International Nuclear Information System (INIS)

Kimler, B.F.; Leeper, D.B.; Snyder, M.H.; Rowley, R.; SChneiderman, M.H.

1982-01-01

The mitotic selection procedure for cell cycle analysis was utilized to investigate the concentration-dependent modification of x-radiation-induced division delay in Chinese hamster ovary (CHO) cells by methyl xanthines (caffeine, theophylline, and theobromine) and by dibutyryl cyclic AMP. The methyl xanthines (concentrations from 0.5 to 1000 μg/ml) all reduced radiation-induced division delay with the effect being linear between approximately 100 and 1000 μg/ml. After doses of 100-300 rad, delay was reduced by 75, 94 or 83 per cent at 1000 μg/ml for each drug, respectively. However, the addition of dibutyryl cyclic AMP had an opposite effect: radiation-induced delay was increased by the concentration range of 0.3 to 300 μg/ml. These results indicate that in mammalian cells the control of cell cycle progression and the modification of radiation-induced division delay are not simply related to intracellular levels of cyclic AMP. Rather, there appear to be at least two competing mechanisms which are differentially affected by caffeine analogues or by direct addition of dibutyryl cyclic AMP. The direct effect of caffeine and the methyl xanthines on membrane calcium permeability is considered. (author)

Structural basis for the enhanced activity of cyclic antimicrobial peptides : The case of BPC194

NARCIS (Netherlands)

Mika, Jacek T.; Moiset, Gemma; Cirac, Anna D.; Feliu, Lidia; Bardaji, Eduard; Planas, Marta; Sengupta, Durba; Marrink, Siewert J.; Poolman, Bert

We report the molecular basis for the differences in activity of cyclic and linear antimicrobial peptides. We iteratively performed atomistic molecular dynamics simulations and biophysical measurements to probe the interaction of a cyclic antimicrobial peptide and its inactive linear analogue with

Effectiveness of screw surface coating on the stability of zirconia abutments after cyclic loading.

Science.gov (United States)

Basílio, Mariana de Almeida; Butignon, Luis Eduardo; Arioli Filho, João Neudenir

2012-01-01

Different surface treatments have been developed in attempts to prevent the loosening of abutment screws. The aim of the current study was to compare the effectiveness of titanium alloy screws with tungsten-doped diamond-like carbon (W-DLC) coating and uncoated screws in providing stability to zirconia (ZrO2) ceramic abutments after cyclic loading. Twenty prefabricated ZrO2 ceramic abutments on their respective external-hex implants were divided into two groups of equal size according to the type of screw used: uncoated titanium alloy screw (Ti) or titanium alloy screw with W-DLC coating (W-DLC/Ti). The removal torque value (preload) of the abutment screw was measured before and after loading. Cyclic loading between 11 and 211 N was applied at an angle of 30 degrees to the long axis of the implants at a frequency of 15 Hz. A target of 0.5 X 106 cycles was defined. Group means were calculated and compared using analysis of variance and the F test (α = .05). Before cyclic loading, the preload for Ti screws was significantly higher than that for W-DLC/Ti screws (P = .021). After cyclic loading, there was no significant difference between them (P = .499). Under the studied conditions, it can be concluded that, after cyclic loading, both abutment screws presented a significant reduction in the mean retained preload and similar effectiveness in maintaining preload.

Synthesis, self-assembly and lipoplex formulation of two novel cyclic phosphonate lipids

Directory of Open Access Journals (Sweden)

JenniferYeh

2013-05-01

Full Text Available Background: Synthetic cationic lipids hold much potential as gene packaging and delivery agents for the treatment of inherited and acquired life threatening diseases, such as cancer, AIDS, cardiovascular diseases, and certain autoimmune disorders. Methods: We report the synthesis, self-assembly as characterized by critical micelle concentrations and plasmid DNA gel retardation using two novel cyclic, phosphonate cationic lipids 2a and 2b, which were synthesized by derivatizing two diastereomeric macrocyclic phosphonates 1a and 1b with a 2-carbon hydroxylamine linker, N, N-dimethylethanolamine (3. Results: The production of cyclic phosphonate lipids 2a and 2b in 73% and 60% yields, respectively, was achieved using classical synthetic methods involving nucleophilic substitution at the phosphorus centre. Conclusions: The synthesis, aggregation and DNA binding properties of these novel cyclic phosphonate lipids suggest that they may have utility serving as gene packaging and delivery agents.

Effect of particle breakage on cyclic densification of ballast: A DEM approach

International Nuclear Information System (INIS)

Thakur, P K; Vinod, J S; Indraratna, B

2010-01-01

In this paper, an attempt has been made to investigate the effect of particle breakage on densification behaviour of ballast under cyclic loading using Discrete Element Method (DEM). Numerical simulations using PFC 2D have been carried out on an assembly of angular particles with and without incorporation of particle breakage. Two-dimensional projection of angular ballast particles were simulated using clusters of bonded circular particles. Degradation of the bonds within a cluster was considered to represent particle breakage. Clump logic was used to make the cluster of particles unbreakable. DEM simulation results highlight that the particle breakage has a profound influence on the cyclic densification behaviour of ballast. The deformation behaviour exhibited by the assembly with breakage is in good agreement with the laboratory experiments. In addition, the evolution of particle displacement vectors clearly explains the breakage mechanism and associated deformations during cyclic loading.

Response of stiff piles in sand to long-term cyclic lateral loading

DEFF Research Database (Denmark)

Bakmar, Christian LeBlanc; Houlsby, Guy T.; Byrne, Byron W.

2010-01-01

. To address this, a series of laboratory tests were conducted where a stiff pile in drained sand was subjected to between 8000 and 60000 cycles of combined moment and horizontal loading. A typical design for an offshore wind turbine monopile was used as a basis for the study, to ensure that pile dimensions...... and loading ranges were realistic. A complete non-dimensional framework for stiff piles in sand is presented and applied to interpret the test results. The accumulated rotation was found to be dependent on relative density and was strongly affected by the characteristics of the applied cyclic load. The pile...... stiffness increased with number of cycles, which contrasts with the current methodology where static p - y curves are degraded to account for cyclic loading. Methods are presented to predict the change in stiffness and the accumulated rotation of a stiff pile due to long-term cyclic loading. The use...

Investigation of using wavelet analysis for classifying pattern of cyclic voltammetry signals

Science.gov (United States)

Jityen, Arthit; Juagwon, Teerasak; Jaisuthi, Rawat; Osotchan, Tanakorn

2017-09-01

Wavelet analysis is an excellent technique for data processing analysis based on linear vector algebra since it has an ability to perform local analysis and is able to analyze an unspecific localized area of a large signal. In this work, the wavelet analysis of cyclic waveform was investigated in order to find the distinguishable feature from the cyclic data. The analyzed wavelet coefficients were proposed to be used as selected cyclic feature parameters. The cyclic voltammogram (CV) of different electrodes consisting of carbon nanotube (CNT) and several types of metal phthalocyanine (MPc) including CoPc, FePc, ZnPc and MnPc powders was used as several sets of cyclic data for various types of coffee. The mixture powder was embedded in a hollow Teflon rod and used as working electrodes. Electrochemical response of the fabricated electrodes in Robusta, blend coffee I, blend coffee II, chocolate malt and cocoa at the same concentrations was measured with scanning rate of 0.05V/s from -1.5 to 1.5V respectively to Ag/AgCl electrode for five scanning loops. The CV of blended CNT electrode with some MPc electrodes indicated the ionic interaction which can be the effect of catalytic oxidation of saccharides and/or polyphenol on the sensor surface. The major information of CV response can be extracted by using several mother wavelet families viz. daubechies (dB1 to dB3), coiflets (coiflet1), biorthogonal (Bior1.1) and symlets (sym2) and then the discrimination of these wavelet coefficients of each data group can be separated by principal component analysis (PCA). The PCA results indicated the clearly separate groups with total contribution more than 62.37% representing from PC1 and PC2.

Bending cyclic load test for crystalline silicon photovoltaic modules

Science.gov (United States)

Suzuki, Soh; Doi, Takuya; Masuda, Atsushi; Tanahashi, Tadanori

2018-02-01

The failures induced by thermomechanical fatigue within crystalline silicon photovoltaic modules are a common issue that can occur in any climate. In order to understand these failures, we confirmed the effects of compressive or tensile stresses (which were cyclically loaded on photovoltaic cells and cell interconnect ribbons) at subzero, moderate, and high temperatures. We found that cell cracks were induced predominantly at low temperatures, irrespective of the compression or tension applied to the cells, although the orientation of cell cracks was dependent on the stress applied. The fracture of cell interconnect ribbons was caused by cyclical compressive stress at moderate and high temperatures, and this failure was promoted by the elevation of temperature. On the basis of these results, the causes of these failures are comprehensively discussed in relation to the viscoelasticity of the encapsulant.

Forsmark site investigation. Investigation of marine and lacustrine sediment in lakes. Field data 2003

Energy Technology Data Exchange (ETDEWEB)

Hedenstroem, Anna [SGU, Uppsala (Sweden)

2003-04-01

The aim of this activity is to describe the aerial and stratigraphical distribution of marine and lacustrine sediment i.e. sediment overlaying the glacial till and/or bedrock surface, in lakes in the Forsmark area. The investigation is carried out within areas where mapping of unconsolidated Quaternary deposits is presently carried out. Since small and shallow lakes cover a large part of the region, this work will give important information on the distribution and stratigraphy of sedimentary deposits not included in the regular mapping of unconsolidated Quaternary deposits within the site investigation programme. Samples were also collected for laboratory analyses of grain size distribution, mineralogical composition as well as the total content of C, N and S and calcium carbonate. The analyses will be carried out on selected samples of representative sedimentary units in order to characterise the chemical and physical properties of the unconsolidated deposits. The analytical data will be useful for the hydrogeological modelling and for models of the Quaternary evolution of the area. The mineralogical analyses of clay may provide information on the origin of the clay particles. One stratigraphic sequence from Lake Eckarfjaerden will be stored for later analyses, e.g. pollen analysis. This report includes field data from spring 2003. Together, the field data and the forthcoming results from the laboratory analyses will form the basis for construction of stratigraphical profiles to be presented in a following report in the fall 2003.

Forsmark site investigation. Investigation of marine and lacustrine sediment in lakes. Field data 2003

International Nuclear Information System (INIS)

Hedenstroem, Anna

2003-04-01

The aim of this activity is to describe the aerial and stratigraphical distribution of marine and lacustrine sediment i.e. sediment overlaying the glacial till and/or bedrock surface, in lakes in the Forsmark area. The investigation is carried out within areas where mapping of unconsolidated Quaternary deposits is presently carried out. Since small and shallow lakes cover a large part of the region, this work will give important information on the distribution and stratigraphy of sedimentary deposits not included in the regular mapping of unconsolidated Quaternary deposits within the site investigation programme. Samples were also collected for laboratory analyses of grain size distribution, mineralogical composition as well as the total content of C, N and S and calcium carbonate. The analyses will be carried out on selected samples of representative sedimentary units in order to characterise the chemical and physical properties of the unconsolidated deposits. The analytical data will be useful for the hydrogeological modelling and for models of the Quaternary evolution of the area. The mineralogical analyses of clay may provide information on the origin of the clay particles. One stratigraphic sequence from Lake Eckarfjaerden will be stored for later analyses, e.g. pollen analysis. This report includes field data from spring 2003. Together, the field data and the forthcoming results from the laboratory analyses will form the basis for construction of stratigraphical profiles to be presented in a following report in the fall 2003

Continuous versus cyclic oral contraceptives for the treatment of endometriosis: a systematic review.

Science.gov (United States)

Zorbas, Konstantinos A; Economopoulos, Konstantinos P; Vlahos, Nikos F

2015-07-01

Recurrence of endometriosis after conservative surgery has been observed in 40-50 % of patients within the first 5 years. A variety of regimens such as combined oral contraceptives, GnRH agonists, danazol, and progestins have been used postoperatively to reduce recurrence rates. Oral contraceptives (oCP) have been used either in a cyclic or in a continuous (no pill-free interval) fashion. The purpose of this article was to summarize the existing evidence on the efficacy and patient compliance for the use of oCP in a continuous versus cyclic fashion following conservative surgery for endometriosis. A systematic search of Medline identified four eligible studies. Studies were considered eligible, if they have evaluated oCP therapy, either in a cyclic or continuous regimen, after conservative surgery for endometriosis. Specifically, studies (1) reporting on women with endometriosis who were treated postoperatively with both continuous oCP and cyclic oCP, (2) written in English, (3) with minimum 6 months duration of medical treatment, and (4) with minimum 12 months duration of follow-up were considered eligible for our systematic review. Outcome measures of these eligible studies were tabulated and then analyzed cumulatively. A purely descriptive approach was adopted concerning all variables. Postoperative use of continuous oCP was associated with a reduction in the recurrence rate of dysmenorrhea, delay in the presentation of dysmenorrhea, reduction in nonspecific pelvic pain, and reduction in the recurrence rate for endometrioma. Use of oCP in a continuous fashion following conservative surgery for endometriosis is more beneficial to cyclic use.

Electron Paramagnetic Resonance Measurements of Reactive Oxygen Species by Cyclic Hydroxylamine Spin Probes.

Science.gov (United States)

Dikalov, Sergey I; Polienko, Yuliya F; Kirilyuk, Igor

2018-05-20

Oxidative stress contributes to numerous pathophysiological conditions such as development of cancer, neurodegenerative, and cardiovascular diseases. A variety of measurements of oxidative stress markers in biological systems have been developed; however, many of these methods are not specific, can produce artifacts, and do not directly detect the free radicals and reactive oxygen species (ROS) that cause oxidative stress. Electron paramagnetic resonance (EPR) is a unique tool that allows direct measurements of free radical species. Cyclic hydroxylamines are useful and convenient molecular probes that readily react with ROS to produce stable nitroxide radicals, which can be quantitatively measured by EPR. In this work, we critically review recent applications of various cyclic hydroxylamine spin probes in biology to study oxidative stress, their advantages, and the shortcomings. Recent Advances: In the past decade, a number of new cyclic hydroxylamine spin probes have been developed and their successful application for ROS measurement using EPR has been published. These new state-of-the-art methods provide improved selectivity and sensitivity for in vitro and in vivo studies. Although cyclic hydroxylamine spin probes EPR application has been previously described, there has been lack of translation of these new methods into biomedical research, limiting their widespread use. This work summarizes "best practice" in applications of cyclic hydroxylamine spin probes to assist with EPR studies of oxidative stress. Additional studies to advance hydroxylamine spin probes from the "basic science" to biomedical applications are needed and could lead to better understanding of pathological conditions associated with oxidative stress. Antioxid. Redox Signal. 28, 1433-1443.

Complexity of chemical graphs in terms of size, branching, and cyclicity.

Science.gov (United States)

Balaban, A T; Mills, D; Kodali, V; Basak, S C

2006-08-01

Chemical graph complexity depends on many factors, but the main ones are size, branching, and cyclicity. Some molecular descriptors embrace together all these three parameters, which cannot then be disentangled. The topological index J (and its refinements that include accounting for bond multiplicity and the presence of heteroatoms) was designed to compensate in a significant measure for graph size and cyclicity, and therefore it contains information mainly on branching. In order to separate these factors, two new indices (F and G) related with J are proposed, which allow to group together graphs with the same size into families of constitutional formulas differing in their branching and cyclicity. A comparison with other topological indices revealed that a few other topological indices vary similarly with index G, notably DN2S4 among the triplet indices, and TOTOP among the indices contained in the Molconn-Z program. This comparison involved all possible chemical graphs (i.e. connected planar graphs with vertex degrees not higher than four) with four through six vertices, and all possible alkanes with four through nine carbon atoms.

Cathodoluminescence characteristics of polycrystalline diamond films grown by cyclic deposition method

International Nuclear Information System (INIS)

Seo, Soo-Hyung; Park, Chang-Kyun; Park, Jin-Seok

2002-01-01

Polycrystalline diamond films were deposited using a cyclic deposition method where the H 2 plasma for etching (t E ) and the CH 4 +H 2 plasma for growing (t G ) are alternately modulated with various modulation ratios (t E /t G ). From the measurement of full width at half maximum and I D /I G intensity ratio obtained from the Raman spectra, it was found that diamond defects and non-diamond carbon phases were reduced a little by adopting the cyclic deposition method. From the cathodoluminescence (CL) characteristics measured for deposited films, the nitrogen-related band (centered at approximately 590 nm) as well as the so-called band-A (centered at approximately 430 nm) were observed. As the cyclic ratio t E /t G increased, the relative intensity ratio of band-A to nitrogen-related band (I A /I N ) was found to monotonically decrease. In addition, analysis of X-ray diffraction spectra and scanning electron microscope morphologies showed that CL characteristics of deposited diamond films were closely related to their crystal orientations and morphologies

Synchrotron X-ray fluorescence studies of a bromine-labelled cyclic RGD peptide interacting with individual tumor cells

International Nuclear Information System (INIS)

Sheridan, Erin J.; Austin, Christopher J. D.; Aitken, Jade B.; Vogt, Stefan; Jolliffe, Katrina A.; Harris, Hugh H.; Rendina, Louis M.

2013-01-01

The first example of synchrotron X-ray fluorescence imaging of cultured mammalian cells in cyclic peptide research is reported. The study reports the first quantitative analysis of the incorporation of a bromine-labelled cyclic RGD peptide and its effects on the biodistribution of endogenous elements (for example, K and Cl) within individual tumor cells. The first example of synchrotron X-ray fluorescence imaging of cultured mammalian cells in cyclic peptide research is reported. The study reports the first quantitative analysis of the incorporation of a bromine-labelled cyclic RGD peptide and its effects on the biodistribution of endogenous elements (for example, K and Cl) within individual tumor cells

Structural Basis for the Catalytic Mechanism of DncV, Bacterial Homolog of Cyclic GMP-AMP Synthase.

Science.gov (United States)

Kato, Kazuki; Ishii, Ryohei; Hirano, Seiichi; Ishitani, Ryuichiro; Nureki, Osamu

2015-05-05

Cyclic dinucleotides (CDNs) play key roles as second messengers and signaling molecules in bacteria and metazoans. The newly identified dinucleotide cyclase in Vibrio cholerae (DncV) produces three different CDNs containing two 3'-5' phosphodiester bonds, and its predominant product is cyclic GMP-AMP, whereas mammalian cyclic GMP-AMP synthase (cGAS) produces only cyclic GMP-AMP containing mixed 2'-5' phosphodiester bonds. We report the crystal structures of V. cholerae and Escherichia coli DncV in complex with various nucleotides in the pre-reaction states. The high-resolution structures revealed that DncV preferably recognizes ATP and GTP as acceptor and donor nucleotides, respectively, in the first nucleotidyl transfer reaction. Considering the recently reported intermediate structures, our pre-reaction state structures provide the precise mechanism of 3'-5' linked cyclic AMP-GMP production in bacteria. A comparison with cGAS in the pre-reaction states suggests that the orientation of the acceptor nucleotide primarily determines the distinct linkage specificities between DncV and cGAS. Copyright © 2015 Elsevier Ltd. All rights reserved.

BCYCLIC: A parallel block tridiagonal matrix cyclic solver

Science.gov (United States)

Hirshman, S. P.; Perumalla, K. S.; Lynch, V. E.; Sanchez, R.

2010-09-01

A block tridiagonal matrix is factored with minimal fill-in using a cyclic reduction algorithm that is easily parallelized. Storage of the factored blocks allows the application of the inverse to multiple right-hand sides which may not be known at factorization time. Scalability with the number of block rows is achieved with cyclic reduction, while scalability with the block size is achieved using multithreaded routines (OpenMP, GotoBLAS) for block matrix manipulation. This dual scalability is a noteworthy feature of this new solver, as well as its ability to efficiently handle arbitrary (non-powers-of-2) block row and processor numbers. Comparison with a state-of-the art parallel sparse solver is presented. It is expected that this new solver will allow many physical applications to optimally use the parallel resources on current supercomputers. Example usage of the solver in magneto-hydrodynamic (MHD), three-dimensional equilibrium solvers for high-temperature fusion plasmas is cited.

A modelling approach for exploring muscle dynamics during cyclic contractions.

Directory of Open Access Journals (Sweden)

Stephanie A Ross

2018-04-01

Full Text Available Hill-type muscle models are widely used within the field of biomechanics to predict and understand muscle behaviour, and are often essential where muscle forces cannot be directly measured. However, these models have limited accuracy, particularly during cyclic contractions at the submaximal levels of activation that typically occur during locomotion. To address this issue, recent studies have incorporated effects into Hill-type models that are oftentimes neglected, such as size-dependent, history-dependent, and activation-dependent effects. However, the contribution of these effects on muscle performance has yet to be evaluated under common contractile conditions that reflect the range of activations, strains, and strain rates that occur in vivo. The purpose of this study was to develop a modelling framework to evaluate modifications to Hill-type muscle models when they contract in cyclic loops that are typical of locomotor muscle function. Here we present a modelling framework composed of a damped harmonic oscillator in series with a Hill-type muscle actuator that consists of a contractile element and parallel elastic element. The intrinsic force-length and force-velocity properties are described using Bézier curves where we present a system to relate physiological parameters to the control points for these curves. The muscle-oscillator system can be geometrically scaled while preserving dynamic and kinematic similarity to investigate the muscle size effects while controlling for the dynamics of the harmonic oscillator. The model is driven by time-varying muscle activations that cause the muscle to cyclically contract and drive the dynamics of the harmonic oscillator. Thus, this framework provides a platform to test current and future Hill-type model formulations and explore factors affecting muscle performance in muscles of different sizes under a range of cyclic contractile conditions.

Random cyclic constitutive models of 0Cr18Ni10Ti pipe steel

International Nuclear Information System (INIS)

Zhao Yongxiang; Yang Bing

2004-01-01

Experimental study is performed on the random cyclic constitutive relations of a new pipe stainless steel, 0Cr18Ni10Ti, by an incremental strain-controlled fatigue test. In the test, it is verified that the random cyclic constitutive relations, like the wide recognized random cyclic strain-life relations, is an intrinsic fatigue phenomenon of engineering materials. Extrapolating the previous work by Zhao et al, probability-based constitutive models are constructed, respectively, on the bases of Ramberg-Osgood equation and its modified form. Scattering regularity and amount of the test data are taken into account. The models consist of the survival probability-strain-life curves, the confidence strain-life curves, and the survival probability-confidence-strain-life curves. Availability and feasibility of the models have been indicated by analysis of the present test data

The Cyclical Relationship Approach in Teaching Basic Accounting Principles.

Science.gov (United States)

Golen, Steven

1981-01-01

Shows how teachers can provide a more meaningful presentation of various accounting principles by illustrating them through a cyclical relationship approach. Thus, the students see the entire accounting relationship as a result of doing business. (CT)

Hydro-climatic changes since 13.000 years B.P. in eastern Tibet and north of Xinjiang (China). Approach using the study of some lacustrine records

International Nuclear Information System (INIS)

Assaraj, A.

1997-01-01

The aim of this study is to build the chronology of the medium and short term climatic changes that took place during the last glacial and Holocene periods using sedimentological and isotopic data obtained on cores from the Aibi lake (north of Xinjiang, China) and from the Madoi and Donxi lakes (eastern part of the Tibetan plateau). At Aibi, after the chemical, isotopic and physico-chemical characterization of the lake waters, and the sedimentological study of the laminae (granulometry and mineralogy) have been done, the measurements of 18 O and 13 C of the authigenous carbonates and of the thickness variations of laminae have evidenced the seasonal character of the laminae. The spectral analyses of the thickness variations indicate periodicities linked with the quasi-biennial oscillations (2 or 3 years) and with the solar cycles (10-11 years). East of the Tibetan plateau, the sedimentological and isotopic study of the cores from the Madoi and Donxi lakes show more humid and hot climate conditions during the lower and middle Holocene. The sedimentary record of lake Madoi show one or several lacustrine or fluvio-lacustrine phases after 13000-12000 years B.P. A high dryness period took place within the Younger Dryas chrono-zone. Since 10000 year B.P. the 3 lakes are filled with isotopically diluted waters. The last glacial-Holocene transition seems to be very sharp and located around 10000 years B.P. both in northern Xinjiang and eastern Tibet and confirm the results previously obtained in Qinghai and northern-Xinjiang. After the optimum hydrologic phase of the lower and middle Holocene, the come back of dryer conditions started at about 6000 or 5000 years B.P. and hydrological conditions became close to the present day ones since 3000 years B.P. (J.S.)

The Reduction of Directed Cyclic Graph for Task Assignment Problem

Directory of Open Access Journals (Sweden)

Ariffin W.N.M.

2018-01-01

Full Text Available In this paper, a directed cyclic graph (DCG is proposed as the task graph. It is undesirable and impossible to complete the task according to the constraints if the cycle exists. Therefore, an effort should be done in order to eliminate the cycle to obtain a directed acyclic graph (DAG, so that the minimum amount of time required for the entire task can be found. The technique of reducing the complexity of the directed cyclic graph to a directed acyclic graph by reversing the orientation of the path is the main contribution of this study. The algorithm was coded using Java programming and consistently produced good assignment and task schedule.

Cyclic fatigue resistance of yttria-stabilized tetragonal zirconia polycrystals with hot isostatic press processing.

Science.gov (United States)

Koyama, Taku; Sato, Toru; Yoshinari, Masao

2012-01-01

This study investigated the influence of surface roughness and cyclic loading on fatigue resistance in Y-TZP subjected to hot isostatic pressing (HIP). Fifty Y-TZP cylinders 3.0 mm in diameter were divided into Group A (polished by centerless method; TZP-CP) or Group B (blasted and acid-etched: TZP-SB150E). Twenty five cp-titanium cylinders (Ti-SB150E) were used as a control. Static and cyclic tests were carried out according to ISO 14801. The cyclic fatigue test was performed in distilled water at 37°C. Surface morphology and roughness as well as crystal phase on the surfaces were also evaluated. Fracture force under the static test was 1,765N (TZP-CP), 1,220N (TZP-SB150E), and 850 N (yield force, Ti-SB150E). Fracture values under the cyclic test decreased to approximately 70% of those under the static tests. These results indicate that HIPed Y-TZP with a 3.0-mm diameter has sufficient durability for application to dental implants.

The Regularities of the Cyclical Development of the World Economy in the Current Phase

Directory of Open Access Journals (Sweden)

Revyakin Georgy V.

2017-09-01

Full Text Available The article is aimed at identifying and describing the key tendencies in the cyclical development of the world economy. In order to allocate the cyclical component in the dynamics of the world-wide GDP growth, a time series decomposition was performed using the Hodrick-Prescott filter and the relationship of economic cycles to the dynamics of different indicators of economic conditions was analyzed. The persistent relationship between inflation, unemployment and the current phase of the economic cycle have been identified and described. The truth of the Phillips curve has been empirically demonstrated: existence of an inverse relationship between the rate of inflation and the level of unemployment. A new classification of branches of economy has been provided according to their susceptibility to the current phase of the economic cycle. According to this criterion, all branches of economy have been divided into the cyclical and the non-cyclical sectors. A hypothesis that there is a direct relationship between the average annual growth rate of GDP and the structure of the national economy has been suggested.

Intermittent, Non Cyclic Severe Mechanical Aortic Valve Regurgitation

Science.gov (United States)

Choi, Jong Hyun; Song, Seunghwan; Lee, Myung-Yong

2013-01-01

Mechanical aortic prosthesis dysfunction can result from thrombosis or pannus formation. We describe an unusual case of intermittent, non cyclic mechanical aortic prosthesis dysfunction due to pannus formation with thrombus in the absence of systolic restriction of disk excursion, that presented with intermittent severe aortic regurgitation. PMID:24459568