Integrating black liquor gasification with pulping - Process simulation, economics and potential benefits

Science.gov (United States)

Lindstrom, Erik Vilhelm Mathias

Gasification of black liquor could drastically increase the flexibility and improve the profit potential of a mature industry. The completed work was focused on research around the economics and benefits of its implementation, utilizing laboratory pulping experiments and process simulation. The separation of sodium and sulfur achieved through gasification of recovered black liquor, can be utilized in processes like modified continuous cooking, split sulfidity and green liquor pretreatment pulping, and polysulfide-anthraquinone pulping, to improve pulp yield and properties. Laboratory pulping protocols have been developed for these modified pulping technologies and different process options evaluated. The process simulation work around BLG has led to the development of a WinGEMS module for the low temperature MTCI steam reforming process, and case studies comparing a simulated conventional kraft process to different process options built around the implementation of a BLG unit operation into the kraft recovery cycle. Pulp yield increases of 1-3% points with improved product quality, and the potential for capital and operating cost savings relative to the conventional kraft process have been demonstrated. Process simulation work has shown that the net variable operating cost for a pulping process using BLGCC is highly dependent on the cost of lime kiln fuel and the selling price of green power to the grid. Under the assumptions taken in the performed case study, the BLGCC process combined with split sulfidity or PSAQ pulping operations had net variable operating cost 2-4% greater than the kraft reference. The influence of the sales price of power to the grid is the most significant cost factor. If a sales price increase to 6 ¢/KWh for green power could be achieved, cost savings of about $40/ODtP could be realized in all investigated BLG processes. Other alternatives to improve the process economics around BLG would be to modify or eliminate the lime kiln unit

New black liquor combustion characteristics III; Mustalipeaen uudet poltto-ominaisuudet III

Energy Technology Data Exchange (ETDEWEB)

Hupa, M.; Forssen, M.; Backman, R.; Enestam, S.; Lauren, T.; Skrifvars, B.J. [Aabo Akademi, Turku (Finland). Combustion Chemistry Research Group

1997-10-01

The main purposes in this work is to: 1. Compare black liquor combustion characterization results to recovery boiler experiences. 2. Study the mechanisms of sodium release in black liquor combustion In the first part results from black liquor combustion characterization tests developed by Aabo Akademi University will be compared to experiences at four Finnish kraft recovery boilers. When comparing the laboratory data to the compiled field data emphasis will be put on the behavior of the black liquor during burning, the release of sodium and potassium, the melting behavior of the deposits and the NO and SO{sub 2} emissions. The main purpose in the second part of the work is to study the release mechanisms of sodium from black liquor char during combustion. Sodium is mainly released from the char by the mechanism where the molten sodiumcarbonate reacts with the char carbon. The study is divided into four subtasks and is performed mainly by conducting experiments in laboratory scale devices: (1) Sodium release during char reactions is studied for different liquors by analyzing the amount of sodium remaining in char after different holding times in a hot inert atmosphere. (2) A DTA/TGA apparatus is used to study in isothermal conditions the char reactions on prepyrolyzed char. (3) The effect of the form of sodium on the sodium release during char reactions. Black liquors added with different sodium salts (Na{sub 2}CO{sub 3}, Na{sub 2}SO{sub 4}, Na{sub 2}S{sub 2}O{sub 2}, Na{sub 2}S sekae NaCl) are used in experiments as in subtask 1. (4) Sodium release during combustion (2-5 % O{sub 2}) of single black liquor particles

Influence of pressure on pyrolysis of black liquor: 1. Swelling.

Science.gov (United States)

Whitty, Kevin; Backman, Rainer; Hupa, Mikko

2008-02-01

This is the first of two papers concerning the behavior of black liquor during pyrolysis under pressurized conditions. Two industrial kraft liquors were pyrolyzed in a laboratory-scale pressurized single particle reactor and a pressurized grid heater at temperatures ranging from 650 to 1100 degrees C and at pressures between 1 and 20 bar. The dimensions of the chars produced were measured and the specific swollen volume was calculated. Swelling decreased roughly logarithmically over the pressure range 1-20 r. An expression is developed to predict the specific swollen volume at elevated pressure when the volume at 1 bar is known. The bulk density of the char increased with pressure, indicating that liquors will be entrained less easily at higher pressures.

Fundamental Study of Black Liquor Gasification Kinetics. Quarterly progress report for the period October 1999 to December 1999

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-01-31

The overall objective of this research is to evaluate the kinetics of gasification of kraft black liquor under laboratory conditions simulating pressurized, oxygen-blown gasification. The significant independent variables are gasifier temperature, black liquor composition particle size, and particle residence time. The authors will quantify their impact on the concentration of major and trace gas phase species, as well as the composition of condensed phase inorganic products, including specification of the Na- and S-containing compounds and overall carbon conversion.

A comprehensive program to develop correlations for physical properties of kraft black liquor. Final report

Energy Technology Data Exchange (ETDEWEB)

Fricke, A.L.; Zaman, A.A.; Stoy, M.O.; Schmidl, G.W.; Dong, D.J.; Speck, B.

1998-04-01

A wide variety of experimental techniques have been used in this work, and many of these have been developed completely or improved significantly in the course of the research done during this program. Therefore, it is appropriate to describe these techniques in detail as a reference for future workers so that the techniques can be used in future work with little additional effort or so that the results reported from this program can be compared better with future results from other work. In many cases, the techniques described are for specific analytical instruments. It is recognized that these may be superseded by future developments and improvements in instrumentation if a complete description of techniques used successfully in the past on other instrumentation is available. The total pulping and liquor preparation research work performed included chip and white liquor preparation, digestion, pulp washing, liquor and wash recovery, liquor sampling, weak liquor concentration in two steps to about 45--50% solids with an intermediate soap skimming at about 140F and 27--30% solids, determination of pulp yield and Kappa number, determination of total liquor solids, and a check on the total material balance for pulping. All other research was performed either on a sample of the weak black liquor (the combined black liquor and washes from the digester) or on the skimmed liquor that had been concentrated.

Carbon distribution in char residue from gasification of kraft black liquor

International Nuclear Information System (INIS)

Sricharoenchaikul, Viboon; Frederick, W.J.; Agrawal, Pradeep

2003-01-01

The char residue yields and the total carbon and carbonate content were measured for dry black liquor solids after pyrolysis or gasification in a laminar entrained-flow reactor. The experimental conditions were 700-1000 deg. C in N 2 ,CO 2 /N 2 or water vapor/N 2 at 1 bar total pressure, for residence times from 0.3 to 1.7 s. Fixed carbon yields, when measured at the same particle residence time, decreased with increasing reactor temperature. CO 2 and water vapor diminished the char carbon significantly at temperatures above 800 deg. C, compared with pyrolysis in N 2 . Water vapor oxidized the char carbon more rapidly than did CO 2 . At 1000 deg. C, the reactions of carbon with sulfate and carbonate became faster, resulting in a smaller difference between carbon conversion rates in the different gas environments. By the end of devolatilization, the amount of carbonate in the char had changed very little at 700-800 deg. C. After devolatilization, carbonate was formed more rapidly at higher temperatures. The presence of CO 2 or water vapor increased the formation of carbonate. In the presence of these gases, more carbonate was measured at all temperatures and residence times. The maximum carbonate measured in the char was 16% of the carbon in the black liquor solids, as compared to 4.4% in the original dry liquor solids. Under most conditions, the carbonate, as a fraction of carbon input, first increased to a constant, temperature-independent value and then decreased

Precipitation and characterisation of lignin obtained from South African kraft mill black liquor

CSIR Research Space (South Africa)

Namane, M

2014-07-01

Full Text Available stream_source_info Namane_2014_ABSTRACT.pdf.txt stream_content_type text/plain stream_size 637 Content-Encoding ISO-8859-1 stream_name Namane_2014_ABSTRACT.pdf.txt Content-Type text/plain; charset=ISO-8859-1 2014... International Conference on Chemical Thermodynamics and South African Institution of Chemical Engineering Conference, Durban, South Africa, 27 July - 1 August 2014 Precipitation and characterisation of lignin obtained from South African kraft mill black...

Stirred cell ultrafiltration of lignin from black liquor generated from South African kraft mills

CSIR Research Space (South Africa)

Kekana, Paul

2016-12-01

Full Text Available Ultrafiltration of lignin from black liquor was carried out in a stirred batch cell using polyethersulfone membranes. Parameters such as operating pressure, feed concentration, stirring rate and membrane cut-off size were varied and their effects...

A survey of present levels of radiocesium in Swedish pulp mill liquors and the implications for wood radiocesium transfer factors. Using Kraft mill liquors as an indicator of wood radiocesium contamination

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

2000-01-01

A survey was initiated to depict and compare the present activity levels in pulp mill liquors from various mill locations. The 137 Cs levels in pulp mill liquors were compared with the mill location and the deposition pattern of the Chernobyl fallout and nuclear weapons fallout. The large input of wood (about 2500 m 3 per day) to an average Nordic Kraft mill and the relatively long-term retention time for radiocesium in the Kraft mill recovery cycle enables representative sampling of substances directly related to the activity concentration in wood. (author)

Investigation of ESEM/EDX to measure liquor penetration and diffusion in Eucalyptus grandis wood chips during kraft pulping

CSIR Research Space (South Africa)

Grzeskowiak, V

2011-01-01

Full Text Available Environmental scanning electron microscopy coupled with energy dispersive x-ray (ESEM/EDX) was optimised to measure the penetration and diffusion of cooking liquor into Eucalyptus grandis wood chips during kraft pulping. The moisture content...

The use of biomass energy in the pulp and paper industry and the prospects for black liquor gasification combined cycle generation

International Nuclear Information System (INIS)

Nilsson, L.J.

1995-01-01

The world production of paper and paperboard products, which increased 3.3% per year since 1980, reached 243 million tonnes in 1991 and is expected to continue to grow by about 2.5% per year over the next decade. Consumption levels in 1990 ranged from 2.8 kg per capita in India to 313 kg per capita in the United States. The biggest producers of pulp are the United States, Canada and the Scandinavian countries, but much of the expansion of pulp production capacity is taking place in countries such as Brazil, Chile and Indonesia. The pulp and paper industry has always relied on biomass as a fuel source to meet process energy demands. Kraft pulping is the most common process accounting for about two thirds of world wood pulp production. Energy recovered from burning black liquor, a lignin-rich by-product, in a chemicals recovery boiler typically provides most of the on-site demand for heat and electricity in a modem kraft pulp mill. Another important fuel source is bark and wood waste generated at the mill. Aging recovery boilers in industrialized countries and increasing electricity/heat demand ratios are stimulating interest in alternative co-generation technologies. Most of the interest in new biomass and black liquor co-generation technologies focuses on those that would utilize gas turbines rather than steam turbines. Gas turbines are generally characterized by higher electricity/heat ratios than steam turbines, as well as lower unit capital costs. With the black liquor and biomass gasification technologies that are now being developed and demonstrated, the energy needs of an energy-efficient kraft pulp mill could be met and 40-50 MW of baseload power would be available for export. Using, in addition, currently unused logging residues for fuel would increase that potential. The pulp and paper industry is likely to be an important early market for advanced biomass-based cogeneration technology owing to its access to biomass fuels and the potential for co

The use of biomass energy in the pulp and paper industry and the prospects for black liquor gasification combined cycle generation

Energy Technology Data Exchange (ETDEWEB)

Nilsson, L J [Department of Environmental and Energy Systems Studies, Lund University, Lund (Sweden)

1995-12-01

The world production of paper and paperboard products, which increased 3.3% per year since 1980, reached 243 million tonnes in 1991 and is expected to continue to grow by about 2.5% per year over the next decade. Consumption levels in 1990 ranged from 2.8 kg per capita in India to 313 kg per capita in the United States. The biggest producers of pulp are the United States, Canada and the Scandinavian countries, but much of the expansion of pulp production capacity is taking place in countries such as Brazil, Chile and Indonesia. The pulp and paper industry has always relied on biomass as a fuel source to meet process energy demands. Kraft pulping is the most common process accounting for about two thirds of world wood pulp production. Energy recovered from burning black liquor, a lignin-rich by-product, in a chemicals recovery boiler typically provides most of the on-site demand for heat and electricity in a modem kraft pulp mill. Another important fuel source is bark and wood waste generated at the mill. Aging recovery boilers in industrialized countries and increasing electricity/heat demand ratios are stimulating interest in alternative co-generation technologies. Most of the interest in new biomass and black liquor co-generation technologies focuses on those that would utilize gas turbines rather than steam turbines. Gas turbines are generally characterized by higher electricity/heat ratios than steam turbines, as well as lower unit capital costs. With the black liquor and biomass gasification technologies that are now being developed and demonstrated, the energy needs of an energy-efficient kraft pulp mill could be met and 40-50 MW of baseload power would be available for export. Using, in addition, currently unused logging residues for fuel would increase that potential. The pulp and paper industry is likely to be an important early market for advanced biomass-based cogeneration technology owing to its access to biomass fuels and the potential for co

Bioconversion of oxygen-pretreated Kraft lignin to microbial lipid with oleaginous Rhodococcus opacus DSM 1069

Energy Technology Data Exchange (ETDEWEB)

Wei, Zhen [Hunan Univ. Changsha (China); Zeng, Guangming [Hunan Univ. Changsha (China); Huang, Fang [Georgia Inst. of Technology, Atlanta, GA (United States); Kosa, Matyas [Georgia Inst. of Technology, Atlanta, GA (United States); Huang, Danlian [Hunan Univ. Changsha (China); Ragauskas, Arthur J. [Georgia Inst. of Technology, Atlanta, GA (United States); Univ. of Tennessee, Knoxville, TN (United States)

2015-04-09

Kraft lignin (KL) from black liquor is an abundantly available, inexpensive aromatic resource that is regarded as a low value compound by the pulp and paper industry, necessitating the development of new applications.

Pressurized pyrolysis and gasification behaviour of black liquor and biofuels

Energy Technology Data Exchange (ETDEWEB)

Whitty, K.; Backman, R.; Hupa, M. [Aabo Akademi, Turku (Finland)

1996-12-01

The objective of this project is to obtain basic experimental data on pyrolysis and gasification of various black liquors and biofuels at elevated pressures, and to model these processes. Liquor-to-liquor differences in conversion behavior of single liquor droplets during gasification at atmospheric pressure were investigated. The applicability of a rate equation developed for catalyzed gasification of carbon was investigated with regard to pressurized black liquor gasification. A neural network was developed to simulate the progression of char conversion during pressurized black liquor gasification. Pyrolysis of black liquor in a pressurized drop-tube furnace was investigated in collaboration with KTH in Stockholm. (author)

Biopulping of sugarcane bagasse and decolorization of kraft liquor by the laccase produced by Klebsiella aerogenes NCIM 2098

Directory of Open Access Journals (Sweden)

Jha H.

2013-12-01

Full Text Available Aims: Laccase, a copper-containing enzyme, oxidizes variety of aromatic compounds. Since laccase is essential for lignin degradation, it can be used for lignin removal in the pulp and paper industry (biopulping. Laccase is also employed as a dechlorinating agent (biobleaching, along with the removal of phenolic and other aromatic pollutants. In the present investigation it was aimed to employ the laccase produced by the bacterium Klebsiella aerogenes along with the bacterium itself in biopulping of sugarcane bagasse and biobleaching of kraft liquor effluent. Methodology and results: A laccase was isolated from the bacterium K. aerogenes, purified to homogeneity and characterized. The enzyme was purified by conventional techniques following salt precipitation, ion exchange chromatography, and affinity chromatography on Con A sepharose. The purified laccase was found to be monomeric glycoprotein with a Mr of 64 kDa when measured by Sephadex G-200 gel chromatography and SDS-PAGE. The Vmax and Km of laccase towards the substrate guaiacol was determined. The optimum pH of the laccase was found to be 5.0. biopulping and biobleaching activities were determined by TAPPI standard methods. Treatment of sugarcane baggase by K. aerogenes also significantly reduced lignin content of the bagasse. Conclusion, significance and impact of study: The bacterium K. aerogenes and a laccase produced by it were used separately for biopulping of sugarcane bagasse and biobleaching of kraft liquor effluent. Treatment with both brought significant reduction in lignin content and kappa number of the pulp. The handsheets prepared from the treated pulp showed improved brightness without affecting the strength properties of paper. The bacterium and the laccase efficiently decolorized the kraft liquor proving to have biobleaching potential.

Single particle studies of black liquor gasification under pressurized conditions

Energy Technology Data Exchange (ETDEWEB)

Whitty, K; Backman, R; Hupa, M; Backman, P; Ek, P; Hulden, S T; Kullberg, M; Sorvari, V

1997-10-01

The purpose of this project is to provide experimental data relevant to pressurized black liquor gasification concepts. Specifically, the following two goals will be achieved: Data on swelling, char yields and component release during pressurized pyrolysis of small samples of black liquor will be obtained. The reactivity and physical behavior of single black liquor droplets during simultaneous pyrolysis and gasification will be investigated. The structure and composition of black liquor char during formation and conversion will be studied. (orig.)

Advancement of High Temperature Black Liquor Gasification Technology

Energy Technology Data Exchange (ETDEWEB)

Craig Brown; Ingvar Landalv; Ragnar Stare; Jerry Yuan; Nikolai DeMartini; Nasser Ashgriz

2008-03-31

Weyerhaeuser operates the world's only commercial high-temperature black liquor gasifier at its pulp mill in New Bern, NC. The unit was started-up in December 1996 and currently processes about 15% of the mill's black liquor. Weyerhaeuser, Chemrec AB (the gasifier technology developer), and the U.S. Department of Energy recognized that the long-term, continuous operation of the New Bern gasifier offered a unique opportunity to advance the state of high temperature black liquor gasification toward the commercial-scale pressurized O2-blown gasification technology needed as a foundation for the Forest Products Bio-Refinery of the future. Weyerhaeuser along with its subcontracting partners submitted a proposal in response to the 2004 joint USDOE and USDA solicitation - 'Biomass Research and Development Initiative'. The Weyerhaeuser project 'Advancement of High Temperature Black Liquor Gasification' was awarded USDOE Cooperative Agreement DE-FC26-04NT42259 in November 2004. The overall goal of the DOE sponsored project was to utilize the Chemrec{trademark} black liquor gasification facility at New Bern as a test bed for advancing the development status of molten phase black liquor gasification. In particular, project tasks were directed at improvements to process performance and reliability. The effort featured the development and validation of advanced CFD modeling tools and the application of these tools to direct burner technology modifications. The project also focused on gaining a fundamental understanding and developing practical solutions to address condensate and green liquor scaling issues, and process integration issues related to gasifier dregs and product gas scrubbing. The Project was conducted in two phases with a review point between the phases. Weyerhaeuser pulled together a team of collaborators to undertake these tasks. Chemrec AB, the technology supplier, was intimately involved in most tasks, and focused primarily on the

Refractive Index of Black and Green Liquors

Directory of Open Access Journals (Sweden)

E. A. Avramenko

2015-01-01

Full Text Available Lack of reliable data on the optical properties of black and green liquors complicates control of their composition in technological process of sulphate cellulose production. In this regard the paper presents measurement results of refraction index of black liquors n (k,t at concentration in solutions of bone-dry solids up to k = 70% and at temperatures t = 10-90 °C, as well as in green liquors n(C,t at the total alkalinity of C = 0-250 g/l and in the same temperature range. All samples of solutions of black and green liquors were provided by Segezha Pulp and Paper Mill and certified in factory laboratory. Measurements were taken by means of the laboratory Abbe refractometer (URL-1, digital refractometer "Expert pro", goniometer spectrometer GS-5, and ultra-violet spectrophotometer as well. The work also presents optical D density spectra in the ultra-violet region of the wavelengths for the samples of a green liquor and main mineral component to form it, i.e. Na2S (sodium sulphide. To calculate dispersion of n (λ in the visible spectral range, here a Lorentz single-oscillator model was used. The paper discusses study results of dispersive dependence of refraction index in green liquors with various concentration and chemical components of n (λ, C forming them at t = 20°C. Computing and experimental dependences of n (λ had not only good qualitative, but also quite satisfactory quantitative compliance. The work also describes main mineral components defining optical properties in these liquors. Given here data on concentration and temperature dependences of a refraction index in black n(k,t and green n(C,t liquors have been never published before. These data are of essential interest to control soda recovery technologies in manufacturing sulphate cellulose. The received results can be also used to tune and calibrate modern domestic and foreign industrial refractometers.

Utilization of black liquor as concrete admixture and set retarder aid

OpenAIRE

El-Mekkawi, Samar A.; Ismail, Ibrahim M.; El-Attar, Mohammed M.; Fahmy, Alaa A.; Mohammed, Samia S.

2011-01-01

The utilization of black liquor, produced by the pulp and paper industry in Egypt, as a workability aid and set retarder admixture has been investigated. This approach may help eliminate the environmentally polluting black liquor waste. It also provides a low cost by-product, which can be widely used in the construction industry. The properties of black liquor and its performance on concrete at two different ratios of water to cement have been studied. The results revealed that black liquor f...

Physical properties of kraft black liquor. Final report. Phase I

Energy Technology Data Exchange (ETDEWEB)

Fricke, A.L.

1983-12-01

Methods were selected, equipment installed, and procedures developed for determining rheological properties; for determining thermal properties (stability, density, thermal expansion, and heat capacity); for purification and characterization of lignin (glass transition, stability, weight average molecular weight, and number average molecular weight); and for performing chemical analyses (negative inorganic ions, positive inorganic ions, acid organic salts, lignin, and total solids). A strategy for pulping to supply test liquors was developed, and a statistically designed pulping experiment was specified for a Southern softwood species. Arrangements were made for performing initial pulping work in an industrial pilot plant, and a preliminary set of pulping experiments were conducted. Liquors from the preliminary pulping experiments were used to test procedures and to determine reproducibility of the experiment. Literature was also surveyed and preliminary selection of designs for a pilot digester, and for equipment to determine surface tension were made.

Fenton process combined with coagulation for the treatment of black liquor from bioethanol wastewater

Science.gov (United States)

Muryanto, Muryanto; Hanifah, Ummu; Amriani, Feni; Ibadurrahman, Ahmad Faiz; Sari, Ajeng Arum

2017-11-01

High amounts of black liquor are generated from bioethanol production by using oil palm empty fruit bunches. The black liquor is waste from alkaline pretreatment, it contains high amount of an alkaline solution (NaOH). The black liquor wastewater was highly contaminated with organic materials, and quite toxic for aquatic ecosystems if discharged directly into waters. This study aimed to determine ability of Fenton process combined with coagulation to treat black liquor. The addition 5% of polyaluminium chloride (PAC) could decolorized black liquor, degraded lignin, and produced sludge 70.64%, 68.28%, and 2.76 gram, respectively. Decolorization of black liquor was in line with degradation of black liquor because lignin is the main compound in black liquor. SEM images after addition of PAC of 5% indicated fragmentation of structure. Fenton reagent consist of 0.7 M FeSO4+ 3M H2O2 has able to decolorize black liquor, degrade lignin, and produce sludge 51.67% and 25.44%, and 0.44 gram, respectively. It was concluded that black liquor wastewater from bioethanol can be treated by using Fenton process combined with coagulation. However, these methods still need improvement to obtain the higher degradation rate, and coagulation sludge needs further consideration.

Treatment of black liquor from the papermaking industry by acidification and reuse.

Science.gov (United States)

Yang, Wen-Bo; Mu, Huan-Zhen; Huang, Yan-Chu

2003-09-01

Two different kinds of black liquor from the papermaking industry were treated by acidification and reuse. The experimental parameters and conditions were discussed in detail. The experimental results indicated that the treatment process mentioned in this article is an effective process for the treatment of black liquor from the papermaking industry. By the treatment, the solid materials in black liquor are transferred into two by-products and the other components are reused or evaporated. Thus, no wastewater except some condensation water would be discharged in pulping process and the problem of pollution of black liquor would be effectively solved.

Performance of Ceriporiopsis sp. in the Treatment of Black Liquor Wastewater

OpenAIRE

Sari, Ajeng Arum

2016-01-01

High amounts of black liquor wastewater are generated from bioethanol production by using oil palm empty fruit bunches. It contains an alkaline solution (NaOH), so it is quite toxic for aquatic ecosystems if discharged directly into waters. Black liquor has been treated by coagulation method, and it still needs additional treatment. This study aimed to determine degradation of black liquor wastewater by selected white-rot fungi (WRF). Five different strains of WRF have been tested for their a...

Numerical modeling of counter-current condensation in a Black Liquor Gasification plant

International Nuclear Information System (INIS)

Risberg, Mikael; Gebart, Rikard

2013-01-01

Pressurized Entrained flow High Temperature Black Liquor Gasification is a novel technique to recover the inorganic chemicals and available energy in black liquor originating from kraft pulping. The gasifier has a direct quench that quickly cools the raw syngas when it leaves the hot reactor by spraying the gas with a water solution. As a result, the raw syngas becomes saturated with steam. Typically the gasifier operates at 30 bar which corresponds to a dew point of about 235 °C and a steam concentration in the saturated syngas that is about 3 times higher than the total concentration of the other species in the syngas. After the quench cooler the syngas is passed through a counter-current condenser where the raw syngas is cooled and most of the steam is condensed. The condenser consists of several vertical tubes where reflux condensation occurs inside the tubes due to water cooling of the tubes on the shell-side. A large part of the condensation takes place inside the tubes on the wall and results in a counterflow of water driven by gravity through the counter current condenser. In this study a computational fluid dynamics model is developed for the two-phase fluid flow on the tube-side of the condenser and for the single phase flow of the shell-side. The two-phase flow was treated using an Euler–Euler formulation with closure correlations for heat flux, condensation rate and pressure drop inside the tubes. The single-phase model for the shell side uses closure correlations for the heat flux and pressure drop. Predictions of the model are compared with results from experimental measurements in a condenser used in a 3 MW Black Liquor Gasification development plant. The results are in good agreement with the limited experimental data that has been collected in the experimental gasifier. However, more validation data is necessary before a definite conclusion can be drawn about the predictive capability of the code. -- Highlights: • A multi-phase model for a

Catalytic mechanism of sodium compounds in black liquor during gasification of coal black liquor slurry

International Nuclear Information System (INIS)

Kuang Jianping; Zhou Junhu; Zhou Zhijun; Liu Jianzhong; Cen Kefa

2008-01-01

The coal black liquor slurry (CBLS) was composed of coal and black pulping liquor, which has plenty of sodium compounds, lignin and cellulose. The sodium compounds have a catalytic effect on the gasification process of coal black liquor slurry, while lignin and cellulose enhance the heat value. Alkali-catalyzed gasification experiments of CBLS and CWS (coal water slurry) are investigated on the thermobalance and fixed bed reactor. The residues of the gasification of CBLS and CWS are analyzed by XRD, SEM and FT-IR. It is found that many micro- and mesopores and zigzag faces exist in the surface of the CBLS coke, which play a key role in the catalytic gasification. Sodium can enhance the reaction potential, weaken the bond of C-O and improve the gasification reaction rate. XRD results show that sodium aluminum silicate and nepheline are the main crystal components of the CBLS and CWS. The C-O stretching vibration peak in the 1060 cm -1 band in the CBLS shifts to 995.65 cm -1 in the CBLS coke after partial gasification. This means that the energy of the C-O stretching vibration in the CBLS carbon matrix decreases, so the structure of the carbon matrix is more liable to react with an oxygen ion or hydroxide ion. The amplitude of the C-O stretching vibration peak is augmented step by step due to the ground-excited level jump of the C-O band

Cracking and Corrosion of Composite Tubes in Black Liquor Recovery Boiler Primary Air Ports

Energy Technology Data Exchange (ETDEWEB)

Keiser, James R.; Singbeil, Douglas L.; Sarma, Gorti B.; Kish, Joseph R.; Yuan, Jerry; Frederick, Laurie A.; Choudhury, Kimberly A.; Gorog, J. Peter; Jetté, Francois R.; Hubbard, Camden R.; Swindeman, Robert W.; Singh, Prett M.; Maziasz, Phillip J.

2006-10-01

Black liquor recovery boilers are an essential part of kraft mills. Their design and operating procedures have changed over time with the goal of providing improved boiler performance. These performance improvements are frequently associated with an increase in heat flux and/or operating temperature with a subsequent increase in the demand on structural materials associated with operation at higher temperatures and/or in more corrosive environments. Improvements in structural materials have therefore been required. In most cases the alternate materials have provided acceptable solutions. However, in some cases the alternate materials have solved the original problem but introduced new issues. This report addresses the performance of materials in the tubes forming primary air port openings and, particularly, the problems associated with use of stainless steel clad carbon steel tubes and the solutions that have been identified.

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr.; Alireza Rezaie

2003-12-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the materials problems encountered during the operation of low-pressure high-temperature (LFHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

Refractory for Black Liquor Gasifiers

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Alireza Rezaie

2003-12-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the materials problems encountered during the operation of low-pressure high-temperature (LFHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

Refractory for Black Liquor Gasifiers

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Alireza Rezaie; Xiaoting Liang; Musa Karakus; Jun Wei

2005-12-01

The University of Missouri-Rolla identified materials that permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project was to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study attempted to define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials were selected or developed that reacted with the gasifier environment to form protective surfaces in

Refractory for Black Liquor Gasifiers

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Xiaoting Liang

2005-10-01

The University of Missouri-Rolla identified materials that permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project was to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study attempted to define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials were selected/developed that either react with the gasifier environment to form protective surfaces in

Refractory for Black Liquor Gasifiers

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick; Musa Karakus; Alireza Rezaie

2004-03-30

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Alireza Rezaie

2004-07-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Alireza Rezaie

2004-10-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Jun Wei

2005-01-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Xiaoting Liang; Jun Wei

2005-04-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Xiaoting Liang

2005-07-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr.; Alireza Rezaie

2004-04-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the materials problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

Causticizing for Black Liquor Gasifiers

Energy Technology Data Exchange (ETDEWEB)

Scott Sinquefeld; James Cantrell; Xiaoyan Zeng; Alan Ball; Jeff Empie

2009-01-07

The cost-benefit outlook of black liquor gasification (BLG) could be greatly improved if the smelt causticization step could be achieved in situ during the gasification step. Or, at a minimum, the increase in causticizing load associated with BLG could be mitigated. A number of chemistries have been proven successful during black liquor combustion. In this project, three in situ causticizing processes (titanate, manganate, and borate) were evaluated under conditions suitable for high temperature entrained flow BLG, and low temperature steam reforming of black liquor. The evaluation included both thermodynamic modeling and lab experimentation. Titanate and manganate were tested for complete direct causticizing (to thus eliminate the lime cycle), and borates were evaluated for partial causticizing (to mitigate the load increase associated with BLG). Criteria included high carbonate conversion, corresponding hydroxide recovery upon hydrolysis, non process element (NPE) removal, and economics. Of the six cases (three chemistries at two BLG conditions), only two were found to be industrially viable: titanates for complete causticizing during high temperature BLG, and borates for partial causticizing during high temperature BLG. These two cases were evaluated for integration into a gasification-based recovery island. The Larsen [28] BLG cost-benefit study was used as a reference case for economic forecasting (i.e. a 1500 tpd pulp mill using BLG and upgrading the lime cycle). By comparison, using the titanate direct causticizing process yielded a net present value (NPV) of $25M over the NPV of BLG with conventional lime cycle. Using the existing lime cycle plus borate autocausticizing for extra capacity yielded a NPV of $16M.

Sulfate reduction in an entrained-flow black liquor gasifier

Energy Technology Data Exchange (ETDEWEB)

Kymaelaeinen, M.; Janka, K. [Tampella Power, Tampere (Finland); Frederick, W.J.; Littau, M.; Sricharoenchaikul, V.; Jivakanun, N.; Waag, K. [Oregon State Univ., Corvallis, OR (United States). Dept. of Chemical Engineering

1995-12-31

Sulfate reduction and carbon conversion during pyrolysis and gasification of black liquor particles were experimentally studied in a laminar entrained-flow reactor. A model was also developed to simulate an entrained-flow black liquor gasifier. Experimental results were then compared to model calculations. Results indicated that carbon must be present to get a high degree of sulfate reduction during gasification. It is therefore important to balance the rates of carbon conversion and sulfate reduction. High local temperatures in the reactor should be avoided so that carbon does not convert too rapidly, but temperatures of nearly 1000 degrees C are required to achieve good sulfate reduction. It was suggested that a new equation was needed to adequately predict sulfate reduction in an entrained-flow black liquor gasifier. 12 refs., 8 figs., 5 tabs.

Impact of burning oil as auxiliary fuel in kraft recovery furnaces upon SO2 emissions

International Nuclear Information System (INIS)

Someshwar, A.V.; Caron, A.L.; Pinkerton, J.E.

1990-01-01

The relationship between burning medium sulfur oil as auxiliary fuel in kraft recovery furnaces and SO 2 emissions was examined. Analysis of long-term CEMS SO 2 data from four furnaces shows no increase in SO 2 emissions as a result of oil burning. The results of field tests conducted at four furnaces while co-firing oil with liquor (up to 34% of total heat input) show that (1) average SO 2 emissions during the oil firing period either decreased or remained unchanged; (2) the overall sulfur retention within the furnace remained consistently high (more than 90%) with increasing levels of oil burning; (3) apportioning stack SO 2 emissions between those derived from oil and black liquor was infeasible. The results indicate that the same alkali fume generation processes that lead to the efficient capture of SO 2 resulting from black liquor combustion may be responsible for the capture of SO 2 resulting from sulfur-containing oil combustion

Nitrogen oxide emissions from a kraft recovery furnace

International Nuclear Information System (INIS)

Prouty, A.L.; Stuart, R.C.; Caron, A.L.

1993-01-01

Nitrogen Oxide (NOx) emissions from a rebuilt kraft recovery furnace slightly exceeded the specified limit of 1.1 lb/ton (0.55 kg/metric ton) of black-liquor solids. Mill trials were undertaken to determine whether NOx emissions could be minimized by modifying furnace operation. NOx emissions increased when secondary air was shifted to tertiary ports. NOx emissions fell when the amounts of primary and total air were decreased, but this increased emissions of other pollutants. After demonstrating that best operation of the furnace could not meet the permit with an emissions limit that matched the furnace's performance at best operation

Utilization of black liquor as concrete admixture and set retarder aid

Directory of Open Access Journals (Sweden)

Samar A. El-Mekkawi

2011-04-01

Full Text Available The utilization of black liquor, produced by the pulp and paper industry in Egypt, as a workability aid and set retarder admixture has been investigated. This approach may help eliminate the environmentally polluting black liquor waste. It also provides a low cost by-product, which can be widely used in the construction industry. The properties of black liquor and its performance on concrete at two different ratios of water to cement have been studied. The results revealed that black liquor from rice straw pulp increases concrete workability, improves compaction, and reduces honeycombing. Moreover, it retards the initial and final set time and enhances uniform compaction. The effect of incorporating small portions of silica fume has been investigated. The ageing effect of this material over a period of one year, to determine its safe storage period, has been studied. Finally, this admixture was found to comply with the relevant Egyptian standards.

Electrocoagulation treatment of black liquor from paper industry.

Science.gov (United States)

Zaied, M; Bellakhal, N

2009-04-30

The procedure of electrocoagulation is an effective, fast and economic technique for treatment of black liquor resulting from paper industry. The effect of electrolysis time, current density, type of electrode material and initial pH were studied in an attempt to achieve a higher removal capacity. Under the optimal experimental conditions (initial pH 7, t=50 min and J=14 mA cm(-2)), the treatment of black liquor by electrocoagulation has led to a removal capacity of 98% of COD, 92% of polyphenols and 99% of color intensity with a good repeatability (R.S.D.industrial interest of this electrochemical process.

Release model for black liquor droplet; Mustalipeaepisaran vapautumismalli

Energy Technology Data Exchange (ETDEWEB)

Saastamoinen, J. [VTT Energy, Espoo (Finland)

1997-10-01

The release of sodium, potassium, chlorine and sulphur from black liquor droplets during pyrolysis, combustion and gasification is studied by modelling work. A model for drying, pyrolysis and swelling of black liquor has been developed earlier. A submodel for the release of sulphur, which takes place at temperatures below 500 deg C has been incorporated to this model. A previous model for the combustion and gasification of char particles has been further developed to account for the effect of sodium, potassium and chlorine. A model for the release of these components as function of time has been developed. (orig.)

Black liquor combustion validated recovery boiler modeling, five-year report

Energy Technology Data Exchange (ETDEWEB)

Grace, T.M.; Frederick, W.J.; Salcudean, M.; Wessel, R.A.

1996-08-01

The objective of this project was to develop a new computer model of a recovery boiler furnace using a computational fluid dynamics (CFD) code specifically tailored to the requirements for solving recovery boiler flows, and using improved submodels for black liquor combustion based on continued laboratory fundamental studies. The project originated in October 1990 and was scheduled to run for four years. At that time, there was considerable emphasis on developing accurate predictions of the physical carryover of macroscopic particles of partially burnt black liquor and smelt droplets out of the furnace, since this was seen as the main cause of boiler plugging. This placed a major emphasis on gas flow patterns within the furnace and on the mass loss rates and swelling and shrinking rates of burning black liquor drops. As work proceeded on developing the recovery boiler furnace model, it became apparent that some recovery boilers encounter serious plugging problems even when physical carryover was minimal. After the original four-year period was completed, the project was extended to address this issue. The objective of the extended project was to improve the utility of the models by including the black liquor chemistry relevant to air emissions predictions and aerosol formation, and by developing the knowledge base and computational tools to relate furnace model outputs to fouling and plugging of the convective sections of the boilers. The work done to date includes CFD model development and validation, acquisition of information on black liquor combustion fundamentals and development of improved burning models, char bed model development, and model application and simplification.

Formation of fuel NOx during black-liquor combustion

International Nuclear Information System (INIS)

Nichols, K.M.; Lien, S.J.

1993-01-01

Fuel NOx and thermal NOx were measured in combustion gases from black liquors in two laboratory furnaces. Combustion at 950 C in air (8% O 2 ) produced NOx concentrations of 40-80ppm. Combustion at 950 C in synthetic air containing no nitrogen (21% 0 2 in Ar) produced the same result, demonstrating that all of the NOx produced during combustion at 950 C was fuel NOx. Formation of fuel NOx increased moderately with increasing temperature in the range of 800-1,000 C, but temperature sensitivity of fuel NOx was much less than that of thermal NOx. The results imply that the major source of NOx in recovery furnace emissions is the fuel NOx in recovery furnace formed by conversion of liquor-bound nitrogen during combustion. This is consistent with thermal NOx theory, which postulates that black-liquor combustion temperatures are too low to generate significant amounts of thermal NOx

REFRACTORY FOR BLACK LIQUOR GASIFIERS

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Jun Wei

2005-03-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

Degradation of black liquor from bioethanol process using coagulation and Fenton-like methods

Science.gov (United States)

Muryanto, Muryanto; Sari, Ajeng Arum; Abimanyu, Haznan

2017-01-01

Black liquor is one of the main by-products of the pretreatment process in bioethanol production from oil palm empty fruit bunches. Black liquor wastewater releases black coloured effluent with high chemical oxygen demand (COD) and low dissolved oxygen (DO). It had a distinctive dark coloration, high alkalinity (pH=13), high organic content (COD > 50,000 ppm) and a high solid content (TSS > 5,000 ppm). Lignin destruction can be done by using high oxidation from OH radical system such as advanced oxidation processes (AOPs). Thereafter, the high concentration of COD, color, and TSS can be removed. The general aim of the present investigation was to determine degradation of black liquor wastewater by using a combined coagulation and Fenton-like methods. In this research, we use Poly Aluminum Chloride (PAC) as a coagulant and FeCl3.6H2O and H2O2 for Fenton-like's reagent. The process was conducted in jar test at 200 rpm for 30 minutes and after that slowly mixed for 2 hours and left for sedimentation 24 hours. 50 ml black liquor was added with variation dose of 1-5% PAC, and 10 % Fenton-like reagent. Hydroxyl radical was generated by the Fenton-like's reagent (ratio FeCl3.6H2O : H2O2 was varied). The highest decolorization of black liquor 70 % was obtained under 5% PAC coagulant. The pH of the wastewater was reduced from 13.00 to 8.07 after the addition of the coagulant. The decolorization of original black liquor was approximately 58% through the Fenton-like process. The combination of PAC and Fenton-like reagent has able to enhance the decolorization of black liquor up to 97%.

Pyrolysis and gasification behavior of black liquor under pressurized conditions

Energy Technology Data Exchange (ETDEWEB)

Whitty, K

1997-11-01

The purpose of this study has been to enhance the understanding of the processes involved in pressurized black liquor gasification. Gasification is known to occur in three stages: drying, pyrolysis and char gasification. The work presented here focuses on the pyrolysis and gasification stages. Experiments were carried out primarily in two laboratory-scale reactors. A pressurized grid heater was used to study black liquor pyrolysis under pressurized conditions. Char yields and the fate of elements in the liquor, as well as the degree of liquor swelling, were measured in this device. A pressurized thermogravimetric reactor was used to measure the rate of the char gasification process under different temperatures and pressures and in various gas atmospheres. Pyrolysis experiments were also carried out in this device, and data on swelling behavior, char yields and component release were obtained 317 refs.

Bio-refinery system in a pulp mill for methanol production with comparison of pressurized black liquor gasification and dry gasification using direct causticization

International Nuclear Information System (INIS)

Naqvi, Muhammad; Yan, Jinyue; Dahlquist, Erik

2012-01-01

Black liquor gasification (BLG) for bio-fuel or electricity production at the modern pulp mills is a field in continuous evolution and the efforts are considerably driven by the climate change, fuel security, and renewable energy. This paper evaluates and compares two BLG systems for methanol production: (i) oxygen blown pressurized thermal BLG; and (ii) dry BLG with direct causticization, which have been regarded as the most potential technology candidates for the future deployment. A key objective is to assess integration possibilities of BLG technologies with the reference Kraft pulp mill producing 1000 air dried tonnes (ADt) pulp/day replacing conventional recovery cycle. The study was performed to compare the systems’ performance in terms of potential methanol production, energy efficiency, and potential CO 2 reductions. The results indicate larger potential of black liquor conversion to methanol from the pressurized BLG system (about 77 million tonnes/year of methanol) than the dry BLG system (about 30 million tonnes/year of methanol) utilizing identical amount of black liquor available worldwide (220 million tDS/year). The potential CO 2 emissions reduction from the transport sector is substantially higher in pressurized BLG system (117 million tonnes/year CO 2 reductions) as compared to dry BLG system (45 million tonnes/year CO 2 reductions). However, the dry BLG system with direct causticization shows better results when considering consequences of additional biomass import. In addition, comparison of methanol production via BLG with other bio-refinery products, e.g. hydrogen, dimethyl ether (DME) and bio-methane, has also been discussed.

Study on the changes of physical and chemical properties for the black liquor of straw plug induced by radiation

International Nuclear Information System (INIS)

Zhu Guanghua; Lan Liqiao

1994-12-01

The black liquor of straw plug was treated by electron beam or γ-ray radiation. The relationship between the viscosity of the black liquor of straw plug and the radiation beam type, the irradiated dose, the temperature of the black liquor at irradiation time and the concentration of the solid state matter in the black liquor was investigated. The result shows that the radiation treatment makes the organic big molecular of the black liquor decomposed, the environmental loading factor of the black liquor reduced; after an irradiation of 20 kGy, the viscosity of the black liquor of straw plug with 30% solid state matter is reduced by 50%, the property of vaporization is obviously improved, but the calorific value of the black liquor has almost no change

Mesta/Kenaf as raw material for Kraft pulping

Energy Technology Data Exchange (ETDEWEB)

Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.

1980-03-15

In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.

Use of sulfide-containing liquors for removing mercury from flue gases

Science.gov (United States)

Nolan, Paul S.; Downs, William; Bailey, Ralph T.; Vecci, Stanley J.

2006-05-02

A method and apparatus for reducing and removing mercury in industrial gases, such as a flue gas, produced by the combustion of fossil fuels, such as coal, adds sulfide ions to the flue gas as it passes through a scrubber. Ideally, the source of these sulfide ions may include at least one of: sulfidic waste water, kraft caustic liquor, kraft carbonate liquor, potassium sulfide, sodium sulfide, and thioacetamide. The sulfide ion source is introduced into the scrubbing liquor as an aqueous sulfide species. The scrubber may be either a wet or dry scrubber for flue gas desulfurization systems.

Studies on inhibition characteristics of corn steep liquor and black sulphite liquor on corrosion of mild steel in acid media

Energy Technology Data Exchange (ETDEWEB)

Deb, P C; Mukherjea, R N

1968-06-01

The purpose of this study was to economically reduce the attack by acid on the parent metal, during the process of removing mill scale by acid pickling. Two inhibitors, by-products of the starch industry and pulp industry, were studied due to their cheapness and availability in India. The inhibition efficiency of the corn steep liquor and black sulfite liquor was found to be below that of thiourea. For example, in 6.2% (w/w) H/sub 2/SO/sub 4/ (at 50/sup 0/C), an inhibition efficiency of 90.5% and 84.5% is reached for inhibitor concentrations of 10 g per liter in the case of corn steep liquor and black sulfite liquor, respectively, while a concentration of 0.25 g per liter of thiourea was required to reach an inhibition efficiency of 98.6%.

Removal of inhibitors from pre-hydrolysis liquor of kraft-based dissolving pulp production process using adsorption and flocculation processes.

Science.gov (United States)

Liu, Xin; Fatehi, Pedram; Ni, Yonghao

2012-07-01

A process for removing inhibitors from pre-hydrolysis liquor (PHL) of a kraft-based dissolving pulp production process by adsorption and flocculation, and the characteristics of this process were studied. In this process, industrially produced PHL was treated with unmodified and oxidized activated carbon as an absorbent and polydiallyldimethylammonium chloride (PDADMAC) as a flocculant. The overall removal of lignin and furfural in the developed process was 83.3% and 100%, respectively, while that of hemicelluloses was 32.7%. These results confirmed that the developed process can remove inhibitors from PHL prior to producing value-added products, e.g. ethanol and xylitol via fermentation. Copyright © 2012 Elsevier Ltd. All rights reserved.

An approach to industrial application: influence of black liquor and pH on xylanase efficiency in bleaching of eucalyptus kraft pulp

OpenAIRE

Fillat Latorre, Úrsula; Roncero Vivero, María Blanca; Bassa, Alexandre; Sacón, Vera Maria

2010-01-01

To obtain a more realistic appraisal of the potential efficiency of xylanases in the industrial bleaching, the influence of pH and the presence of black liquor (measured as COD) on the bleaching efficiency of two commercial xylanases was studied at high temperature. These pH’s, CODs, and temperatures are close to those used in the storage tower of the B fiber line in Jacareı´ unit of Fibria (Brazil). The pulp samples obtained after each bleaching stage were analyzed for kappa number, brigh...

Delignification of softwood kraft pulp by chlorine dioxide in a laboratory bleaching liquor displacement reactor

International Nuclear Information System (INIS)

Hamzeh, Y.; Izadyar, S.

2008-01-01

The chlorine dioxide delignification efficiency of softwood kraft pulp in the laboratory liquor displacement reactor (fixed bed reactor) was investigated and compared with conventional batch reactor. The comparison of two reactors was made based on the effective efficiency and overall efficiency of chlorine dioxide. Effective efficiency corresponds to the oxidizing capacity of chlorine dioxide which consumed by organic materials. Comparison of two reactors based on the effective efficiency showed that the selectivity of delignification significantly enhanced in the displacement reactor in which the primary reaction products are eliminated from reaction zone by displacing flow. On the other hand, the formation of high amounts of chlorate in the reaction zone of displacement reactor reduces the overall efficiency of chlorine dioxide delignification stage. Thus, in spite of significant decrease in useless secondary reactions, this type of reactor would not be cost effective in the industrial scale

New black liquor combustion characteristics II; Mustalipeaen uudet poltto-ominaisuudet II

Energy Technology Data Exchange (ETDEWEB)

Hupa, M.; Backman, R.; Bostroem, S.; Forssen, M.; Uusikartano, T. [Aabo Akademi, Turku (Finland)

1996-12-01

In an earlier study (LIEKKI 2, Y 17), the combustion characteristics of 17 liquors of different origin were studied by four laboratory tests. These tests were (1) single droplet burning, (2) single droplet pyrolysis, (3) pressurized gasification, and (4) calculation of melting properties of inorganic carryover particles. The study showed that there are big differences between liquors of different origin. These differences strongly affect the combustion properties, i.e. pyrolysis and burning times, swelling, and fouling tendency of heat transfer surfaces. The objective for the present research project was to investigate the reasons why some properties affect the combustion behavior more than others. The project is partly complementary to the previous study, partly a more detailed study of some of the phenomena observed earlier. The work constitutes of the following studies: (1) further study of several more liquors by the same methods, (2) pyrolysis swelling in inert gas (N{sub 2}) at two temperatures, 700 deg C and 900 deg C, (3) effect of heat treatment black liquors, (4) effect of addition of sodium compounds to a virgin black liquor, (5) data treatment and correlations, (6) nitrogen oxide formation tendency. (author)

Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer

Energy Technology Data Exchange (ETDEWEB)

Kevin Whitty

2007-06-30

University of Utah's project entitled 'Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer' (DOE Cooperative Agreement DE-FC26-02NT41490) was developed in response to a solicitation released by the U.S. Department of Energy in December 2001, requesting proposals for projects targeted towards black liquor/biomass gasification technology support research and development. Specifically, the solicitation was seeking projects that would provide technical support for Department of Energy supported black liquor and biomass gasification demonstration projects under development at the time.

Hydrogen production by supercritical water gasification of alkaline black liquor

Energy Technology Data Exchange (ETDEWEB)

Cao, Changqing; Guo, Liejin; Chen, Yunan; Lu, Youjun [Xi' an Jiatong Univ. (China)

2010-07-01

Black liquor was gasified continuously in supercritical water successfully and the main gaseous products were H{sub 2}, CO{sub 2} and CH{sub 4} with little amount of CO, C{sub 2}H{sub 4} and C{sub 2}H{sub 6}. The increase of the temperature and the decrease of the flow rate and black liquor concentration enhanced SCWG of black liquor. The change of the system pressure had limited influence on the gasification effect. The maximal COD removal efficiency of 88.69 % was obtained at the temperature of 600 C. The pH values of the aqueous residue were all decreased to the range of 6.4{proportional_to}8 while the pH value of cooling effluence below 360 C increased to about 11 and the sodium content was much higher than that in the aqueous residue. The reaction rate for COD degradation in supercritical water was obtained by assuming pseudo first order reaction. And the activation energy and pre-exponential for COD removal in SCWG were 74.38kJ/mol and 1.11 x 10{sup 4} s{sup -1} respectively. (orig.)

Alternative Technologies for Biofuels Production in Kraft Pulp Mills—Potential and Prospects

Directory of Open Access Journals (Sweden)

Esa Vakkilainen

2012-07-01

Full Text Available The current global conditions provide the pulp mill new opportunities beyond the traditional production of cellulose. Due to stricter environmental regulations, volatility of oil price, energy policies and also the global competitiveness, the challenges for the pulp industry are many. They range from replacing fossil fuels with renewable energy sources to the export of biofuels, chemicals and biomaterials through the implementation of biorefineries. In spite of the enhanced maturity of various bio and thermo-chemical conversion processes, the economic viability becomes an impediment when considering the effective implementation on an industrial scale. In the case of kraft pulp mills, favorable conditions for biofuels production can be created due to the availability of wood residues and generation of black liquor. The objective of this article is to give an overview of the technologies related to the production of alternative biofuels in the kraft pulp mills and discuss their potential and prospects in the present and future scenario.

Elimination of Phenol and Color from Pulping Black Liquor Using Electrocoagulation Process

Directory of Open Access Journals (Sweden)

Nahid Rastegarfar

2013-08-01

Full Text Available There are many non-wood lignocelluloses resources such as wheat, rice straw and other agriculture by- products with appropriate feature for pulp production in Iran. The most major deterrent to their use is presence of pulping black liquor that due to lignin of lignocelluloses solution contains significant amounts of color and phenol compounds. The aim of this paper was investigation of the ability to remove phenol and color as the most important organic pollutants from back liquor of agri-based pulping process using electrocoagulation method. In the electrocoagulation process aluminium electrode was used and cell potential and current intensity were adjusted on 16 V and 1700 mA respectively. The effect of various treatment time (10, 25, 40, 55, 70 min and initial pH (3, 5, 7, 9, 10/5 of black liquor were investigated.The results showed that maximum of decrease obtained at pH 5 that has led to a remove capacity 78% of phenol and 98% of color in treatment time 70 min. electrocoagulation method can be used for black liquor treatment because of simple, effective and its low investment cost compared to other technologies.

Comparison of pulp-mill-integrated hydrogen production from gasified black liquor with stand-alone production from gasified biomass

International Nuclear Information System (INIS)

Andersson, E.; Harvey, S.

2007-01-01

When gasified black liquor is used for hydrogen production, significant amounts of biomass must be imported. This paper compares two alternative options for producing hydrogen from biomass: (A) pulp-mill-integrated hydrogen production from gasified back liquor; and (B) stand-alone production of hydrogen from gasified biomass. The comparison assumes that the same amount of biomass that is imported in Alternative A is supplied to a stand-alone hydrogen production plant and that the gasified black liquor in Alternative B is used in a black liquor gasification combined cycle (BLGCC) CHP unit. The comparison is based upon equal amounts of black liquor fed to the gasifier, and identical steam and power requirements for the pulp mill. The two systems are compared on the basis of total CO 2 emission consequences, based upon different assumptions for the reference energy system that reflect different societal CO 2 emissions reduction target levels. Ambitions targets are expected to lead to a more CO 2 -lean reference energy system, in which case hydrogen production from gasified black liquor (Alternative A) is best from a CO 2 emissions' perspective, whereas with high CO 2 emissions associated with electricity production, hydrogen from gasified biomass and electricity from gasified black liquor (Alternative B) is preferable. (author)

A combined acidification/PEO flocculation process to improve the lignin removal from the pre-hydrolysis liquor of kraft-based dissolving pulp production process.

Science.gov (United States)

Shi, Haiqiang; Fatehi, Pedram; Xiao, Huining; Ni, Yonghao

2011-04-01

The presence of lignin impairs the utilization of the hemicelluloses dissolved in the pre-hydrolysis liquor (PHL) of the kraft-based dissolving pulp production process. In this paper, a novel process was developed by combining the acidification and poly ethylene oxide (PEO) flocculation concepts to improve the lignin removal. The results showed that the lignin removal was improved by the addition of PEO to the acidified PHL, particularly at a low pH of 1.5. The main mechanisms involved are the lignin/PEO complex formation and the bridging of the formed complexes. This hypothesis was supported by the turbidity, FTIR and particle size measurements. Interestingly, the hemicelluloses removal from the acidification/PEO flocculation was marginal, which would be beneficial for the down-stream ethanol production from the PHL. Additionally, a process flow diagram was proposed that incorporates this new concept into the existing configuration of kraft-based dissolving pulp production process. Copyright © 2011 Elsevier Ltd. All rights reserved.

Lignin derivatives from desilicated rice straw soda black liquor

Energy Technology Data Exchange (ETDEWEB)

El-Taraboulsi, M A; Nasser, M M

1979-01-01

Carboxymethyl lignin, cyanoethyl lignin, carboxyethyl lignin, and aminopropyl lignin were prepared from alkali lignin of rice straw black liquor (after disilication by storage for 1 wk to 1 yr) and used as sizes for paper, drilling fluid additives and flocculants.

ESTUDO DA ADIÇÃO DA LIGNINA KRAFT NAS PROPRIEDADES MECÂNICAS DOS BRIQUETES DE RESÍDUOS DA INDÚSTRIA MOVELEIRA

Directory of Open Access Journals (Sweden)

Adriana de Fátima Gomes Gouvêa

2017-01-01

Full Text Available In order to improve global effectiveness of energy production, a strategy is the model of bio-refineries in which all the components of biomass are totally used to produce a range of products with aggregated value. The kraft lignin is one of the products originated in the process of cellulose production that can be used in making densified products. The objective of this work was to evaluate the behavior of the addition of extracted kraft lignin of black kraft liquor in briquette manufactures with furniture industry waste, in the form of shavings and panel particles in different proportions. The briquettes were produced in laboratory briquetting, using the temperatures of 60, 75 and 90 o C. The pressing and cooling time was 5 minutes and pressure 68,9 x 10 5 N.m -2 (1000 PSI. The briquette quality was evaluated through determining the mechanical properties. The kraft lignin in adequate proportions and temperature showed advantages in the increase of resistance and the durability of the briquettes. The kraft lignin presented advantages such as agglutinative in briquette productions from wood waste at a pressing temperature of 90 o C with addition of 20% of kraft lignin, and at pressing temperatures of 60 and 75 o C at a proportion of addition of 40 and 60% of kraft lignin to wood waste, respectively.

Refractory for Black Liquor Gasifiers

Energy Technology Data Exchange (ETDEWEB)

William L. Headrick Jr; Musa Karakus; Xiaoting Laing

2005-10-01

The University of Missouri-Rolla will identify materials that will permit the safe, reliable and economical operation of combined cycle gasifiers by the pulp and paper industry. The primary emphasis of this project will be to resolve the material problems encountered during the operation of low-pressure high-temperature (LPHT) and low-pressure low-temperature (LPLT) gasifiers while simultaneously understanding the materials barriers to the successful demonstration of high-pressure high-temperature (HPHT) black liquor gasifiers. This study will define the chemical, thermal and physical conditions in current and proposed gasifier designs and then modify existing materials and develop new materials to successfully meet the formidable material challenges. Resolving the material challenges of black liquor gasification combined cycle technology will provide energy, environmental, and economic benefits that include higher thermal efficiencies, up to three times greater electrical output per unit of fuel, and lower emissions. In the near term, adoption of this technology will allow the pulp and paper industry greater capital effectiveness and flexibility, as gasifiers are added to increase mill capacity. In the long term, combined-cycle gasification will lessen the industry's environmental impact while increasing its potential for energy production, allowing the production of all the mill's heat and power needs along with surplus electricity being returned to the grid. An added benefit will be the potential elimination of the possibility of smelt-water explosions, which constitute an important safety concern wherever conventional Tomlinson recovery boilers are operated. Developing cost-effective materials with improved performance in gasifier environments may be the best answer to the material challenges presented by black liquor gasification. Refractory materials may be selected/developed that either react with the gasifier environment to form protective

Application of a mechanism-based rate equation to black liquor gasification rate data

Energy Technology Data Exchange (ETDEWEB)

Overacker, N.L.; Waag, K.J.; Frederick, W.J. [Oregon State University, OR (United States). Dept. of Chemical Engineering; Whitty, K.J.

1995-09-01

There is growing interest worldwide to develop alternate chemical recovery processes for paper mills which are cheaper, safer, more efficient and more environmentally sound than traditional technology. Pressurized gasification of black liquor is the basis for many proposed schemes and offers the possibility to double the amount of electricity generated per unit of dry black liquor solids. Such technology also has capital, safety and environmental advantages. One of the most important considerations regarding this emerging technology is the kinetics of the gasification reaction. This has been studied empirically at Aabo Akademi University for the pressurized gasification with carbon dioxide and steam. For the purposes of reactor modeling and scale-up, however, a thorough understanding of the mechanism behind the reaction is desirable. This report discusses the applicability of a mechanism-based rate equation to gasification of black liquor. The mechanism considered was developed for alkali-catalyzed gasification of carbon and is tested using black liquor gasification data obtained during simultaneous reaction with H{sub 2}O and CO. Equilibrium considerations and the influence of the water-gas shift reaction are also discussed. The work presented here is a cooperative effort between Aabo Akademi University and Oregon State University. The experimental work and some of the data analysis was performed at Aabo Akademi University. Development of the models and consideration of their applicability was performed primarily at Oregon State University

Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills.

Science.gov (United States)

Naqvi, M; Yan, J; Fröling, M

2010-02-01

There is great interest in developing black liquor gasification technology over recent years for efficient recovery of bio-based residues in chemical pulp mills. Two potential technologies of producing dimethyl ether (DME) and methane (CH(4)) as alternative fuels from black liquor gasification integrated with the pulp mill have been studied and compared in this paper. System performance is evaluated based on: (i) comparison with the reference pulp mill, (ii) fuel to product efficiency (FTPE) and (iii) biofuel production potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH(4) production globally in terms of black liquor availability. BPP and FTPE of CH(4) production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill.

Method of Black Liquor Combustion to Remove Silicon from Wheat Straw Pulping

Directory of Open Access Journals (Sweden)

Yongjian Xu

2015-02-01

Full Text Available The effects of aluminium sulphate and sodium aluminate on physical and chemical properties of wheat straw pulp black liquor were studied. Results showed that the expansion rate was enhanced by increasing the aluminum salt content; furthermore, the effect of sodium aluminate was better than that of aluminum sulfate. The maximum desilication rate of 92.31% was reached with the addition of 3% sodium aluminate. A rheometer showed that aluminum salt had little impact on the viscosity of thick black liquor, so even at a high temperature it could be conveyed by pumps in paper mill at 110 °C. The effect of aluminium salt on the silicon removal rate during black liquor combustion was also studied. The experimental results showed that both aluminium sulphate and sodium aluminate helped to remove silicon. The desilication rate of sodium aluminate reached 62.33%, higher than that of aluminum sulphate. SEM-EDX illustrated that the aluminum and silicon ions were formed into insoluble precipitates. It was optimal to use 3% sodium aluminate as desilication agent.

Synthetic gas production from dry black liquor gasification process using direct causticization with CO2 capture

International Nuclear Information System (INIS)

Naqvi, Muhammad; Yan, Jinyue; Dahlquist, Erik

2012-01-01

Highlights: ► We study synthetic gas production from dry black liquor gasification system. ► Direct causticization eliminates energy intensive lime kiln reducing biomass use. ► Results show large SNG production potential at significant energy efficiency (58%). ► Substantial CO 2 capture potential plus CO 2 reductions from natural gas replacement. ► Significant transport fuel replacement especially in Sweden and Europe. -- Abstract: Synthetic natural gas (SNG) production from dry black liquor gasification (DBLG) system is an attractive option to reduce CO 2 emissions replacing natural gas. This article evaluates the energy conversion performance of SNG production from oxygen blown circulating fluidized bed (CFB) black liquor gasification process with direct causticization by investigating system integration with a reference pulp mill producing 1000 air dried tonnes (ADt) of pulp per day. The direct causticization process eliminates use of energy intensive lime kiln that is a main component required in the conventional black liquor recovery cycle with the recovery boiler. The paper has estimated SNG production potential, the process energy ratio of black liquor (BL) conversion to SNG, and quantified the potential CO 2 abatement. Based on reference pulp mill capacity, the results indicate a large potential of SNG production (about 162 MW) from black liquor but at a cost of additional biomass import (36.7 MW) to compensate the total energy deficit. The process shows cold gas energy efficiency of about 58% considering black liquor and biomass import as major energy inputs. About 700 ktonnes per year of CO 2 abatement i.e. both possible CO 2 capture and CO 2 offset from bio-fuel use replacing natural gas, is estimated. Moreover, the SNG production offers a significant fuel replacement in transport sector especially in countries with large pulp and paper industry e.g. in Sweden, about 72% of motor gasoline and 40% of total motor fuel could be replaced.

Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

Energy Technology Data Exchange (ETDEWEB)

Martins, Fernanda Machado [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil); Munhoz Martins, Joaniel [Laboratorio de Analise de Minerais e Rochas (LAMIR-UFPR) (Brazil); Ferracin, Luiz Carlos [Laboratorio Quimico da Votorantin Cimentos (Brazil); Cunha, Carlos Jorge da [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil)]. E-mail: cjdcunha@quimica.ufpr.br

2007-08-17

Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase.

Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

International Nuclear Information System (INIS)

Martins, Fernanda Machado; Munhoz Martins, Joaniel; Ferracin, Luiz Carlos; Cunha, Carlos Jorge da

2007-01-01

Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase

IMPACT OF FURFURAL ON THE SUGAR ANALYSIS OF PRE-HYDROLYSIS LIQUOR OF KRAFT-BASED DISSOLVING PULP PRODUCTION PROCESS USING THE HPAEC TECHNIQUE

Directory of Open Access Journals (Sweden)

Abrar Saeed

2011-03-01

Full Text Available High performance anion-exchange chromatography with pulse ampero-metric detector (HPAEC-PAD is a reliable method to systematically determine the sugar contents in pulp and paper waste streams, including bleaching and extraction liquors. We used the same method to determine the sugar content of industrially produced pre-hydrolysis liquor (PHL from a kraft-based dissolving pulp production process. The analysis showed that the traditional method cannot be applied for sugar analysis, and an improvement on the method was required. In fact, the presence of furfural in the PHL sample was the reason for the required modification. It was noted that the removal of furfural via evaporation could improve the reliability of the HPAEC technique for sugar assessments. If the concentration of furfural was higher than 0.045% (wt. in the PHL, the error introduced in the sugar analysis was profound. Also, the industrially produced PHL contained more furfural than the laboratory produced PHL under the same hydrolysis conditions. Consequently, the concentration of furfural in the PHL should be taken into account for sugar analysis using the HPAEC technique.

The effect of alkali on the product distribution from black liquor conversion under supercritical water.

Science.gov (United States)

Hawangchu, Y; Atong, D; Sricharoenchaikul, V

2017-07-01

Lignin in chemical pulping waste, or black liquor (BL), can be converted into various products via supercritical water gasification (SCWG). However, the inherited alkaline contents from the pulping chemicals may affect the product yields and properties. In this research, the influence of the residual alkali on the product distribution via SCWG of soda BL and kraft BL was evaluated. The SCWG was performed in a batch quartz reactor for 10 min at various temperatures (673, 773 and 873 K) and pressures (250, 300 and 400 bar). The highest hydrogen (H 2 ) production occurred at 873 K for the soda BL. The water-gas shift reaction with sodium ions played an important part in the H 2 production, while only small amounts of methane and carbon monoxide were detected. Hydrocarbons, carboxylic acids and esters were the dominant substrates in the liquid products, which denoted the potential of this method for bond cleaving of the lignin macromolecule. As a result, BL, which typically contains alkali salt, was an appropriate feedstock for the SCWG reaction to produce renewable fuel. This method not only has a positive influence on the generation of value added products from highly corrosive waste but also helps avoid some technical problems commonly encountered with direct firing in a recovery boiler.

Feasibility of wood pulping black liquor for treatment of soybean ...

African Journals Online (AJOL)

use

2011-11-23

Nov 23, 2011 ... This study was carried out to determine the effects of neutral black liquor and moisture heating treatments ... The most commonly used methods of protecting protein include ..... Induced non-enzymatic browning of soybean meal for enhancing efficiency of ... ammonia relase of soluble soybean meal proterin.

Exploring the antioxidant potential of lignin isolated from black liquor of oil palm waste.

Science.gov (United States)

Bhat, Rajeev; Khalil, H P S A; Karim, A A

2009-09-01

This study was conducted to evaluate the potential antioxidant activity of lignin obtained from black liquor, a hazardous waste product generated during the extraction of palm oil. Antioxidant potential of the extracted lignin was evaluated by dissolving the extracted samples in 2 different solvent systems, namely, 2-methoxy ethanol and DMSO. Results revealed high percent inhibition of the 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical in the lignin sample dissolved in 2-methoxy ethanol over DMSO (concentration range of 1-100 microg/ml). Lignin extracted in 2-methoxy ethanol exhibited higher inhibition percentage (at 50 microg/ml, 84.2%), whereas a concentration of 100 microg/ml was found to be effective in the case of the DMSO solvent (69.8%). Fourier transform infrared (FTIR) spectrometry revealed that the functional groups from the extracted lignin and commercial lignin were highly similar, indicating the purity of the lignin extracted from black liquor. These results provide a strong basis for further applications of lignin in the food industry and also illustrate an eco-friendly approach to utilize oil palm black liquor.

Rapid determination of methanol in black liquors by full evaporation headspace gas chromatography.

Science.gov (United States)

Li, Hailong; Zhan, Huaiyu; Fu, Shiyu; Liu, Mengru; Chai, Xin-Sheng

2007-12-14

This paper reported a full evaporation headspace gas chromatographic (GC) technique for determination of methanol content in black liquors (pulping spent liquor). In this method, a very small volume (10-20 microL) of liquor sample is introduced into a headspace sample vial (20 mL) and heated up to a temperature of 105 degrees C. A near-complete mass transfer of methanol from the liquid phase to vapor phase (headspace), i.e., a full evaporation, can be achieved within 3 min. The methanol in the headspace of the vial is then measured by GC. The present method is simple, rapid and accurate.

Elimination of Phenol and Color from Pulping Black Liquor Using Electrocoagulation Process

OpenAIRE

Nahid Rastegarfar; Rabi Behrouz; Nader Bahramifar

2013-01-01

There are many non-wood lignocelluloses resources such as wheat, rice straw and other agriculture by- products with appropriate feature for pulp production in Iran. The most major deterrent to their use is presence of pulping black liquor that due to lignin of lignocelluloses solution contains significant amounts of color and phenol compounds. The aim of this paper was investigation of the ability to remove phenol and color as the most important organic pollutants from back liquor of agri-bas...

DETERMINACIÓN DE FENOLES TOTALES EN DERIVADOS LÍGNICOS OBTENIDOS DEL “LICOR NEGRO” COMO ALTERNATIVA DE PRODUCCIÓN // DETERMINATION OF TOTAL PHENOL DERIVATIVES OBTAINED FROM LIGNIN "BLACK LIQUOR" AS ALTERNATIVE TO PRODUCTION

Directory of Open Access Journals (Sweden)

María José López Villalobos

2015-06-01

Full Text Available Lignin is an industrial waste being worthless in papermaking byproduct of black liquor obtained from the pulping process in some Venezuelan plants. The black liquor is obtained from the Kraft pulping process to extract lignin sulphite by acid precipitation and quantify the amount of total phenols in such lignin products used in this study. Spectrophotometry Molecular absorption in the UV-Visible and Infrared Spectroscopy (FTIR region were used to carry out these study techniques. The products obtained in the study had the same signs than commercial lignin (LA, along with the extracted lignin present little degradation HCl, confirmed by infrared spectra. Also, the amount of total phenols was quantified in derivative lignin obtained using the Folin-Ciocalteu. In the sulphite process extracted lignin with acetic acid derivative contains more phenols, and in the Kraft process, the derivative lignin extracted with fewer nitric acid present. The amount of total phenolics present in these derivatives are good for making antiseptics, detergents, nylon, resin and many industrial products. // RESUMEN La lignina es un subproducto del licor negro obtenido del proceso de despulpado en algunas plantas de Venezuela, siendo un desecho industrial que carece de valor en la fabricación de papel. En este estudio se utilizó el licor negro obtenido de los procesos de pulpado Kraft y Sulfito para extraer la lignina mediante precipitaciones ácidas y cuantificar la cantidad de fenoles totales en dichos productos lígnicos. Para llevar a cabo este estudio, se utilizaron las técnicas de Espectrofotometría de Absorción Molecular en la región UV-Visible y la Espectroscopia de Infrarrojo (FTIR. Los productos obtenidos en el estudio presentaron señales similares que la lignina comercial (LA, además la lignina extraída con HCl presentó poca degradación, corroborado por los espectros infrarrojos. Asimismo, se cuantificó la cantidad de fenoles totales en los

Estimation of Theaflavins (TF) and Thearubigins (TR) Ratio in Black Tea Liquor Using Electronic Vision System

Science.gov (United States)

Akuli, Amitava; Pal, Abhra; Ghosh, Arunangshu; Bhattacharyya, Nabarun; Bandhopadhyya, Rajib; Tamuly, Pradip; Gogoi, Nagen

2011-09-01

Quality of black tea is generally assessed using organoleptic tests by professional tea tasters. They determine the quality of black tea based on its appearance (in dry condition and during liquor formation), aroma and taste. Variation in the above parameters is actually contributed by a number of chemical compounds like, Theaflavins (TF), Thearubigins (TR), Caffeine, Linalool, Geraniol etc. Among the above, TF and TR are the most important chemical compounds, which actually contribute to the formation of taste, colour and brightness in tea liquor. Estimation of TF and TR in black tea is generally done using a spectrophotometer instrument. But, the analysis technique undergoes a rigorous and time consuming effort for sample preparation; also the operation of costly spectrophotometer requires expert manpower. To overcome above problems an Electronic Vision System based on digital image processing technique has been developed. The system is faster, low cost, repeatable and can estimate the amount of TF and TR ratio for black tea liquor with accuracy. The data analysis is done using Principal Component Analysis (PCA), Multiple Linear Regression (MLR) and Multiple Discriminate Analysis (MDA). A correlation has been established between colour of tea liquor images and TF, TR ratio. This paper describes the newly developed E-Vision system, experimental methods, data analysis algorithms and finally, the performance of the E-Vision System as compared to the results of traditional spectrophotometer.

Evaluation of treated black liquor used as dispersant of concentrated coal-water slurry

Energy Technology Data Exchange (ETDEWEB)

Mingsong Zhou; Qian Kong; Bing Pan; Xueqing Qiu; Dongjie Yang; Hongming Lou [South China University of Technology, Guangzhou (China). State Key Laboratory of Pulp and Paper Engineering

2010-03-15

The paper making waste liquor is a great water pollution source and much work has been done over the years to overcome this challenge. We present here a solution of black liquor used as dispersant of coal-water slurry (abbreviated as CWS) following chemical treatment. The treated black liquor (abbreviated as TBL) is used to prepare CWS for three bituminous coals, and the factors influencing its dispersing ability and the properties of CWS are investigated. The results show that the increasing sulfonating agent and formaldehyde dosage increase the sulfonic group content while reducing the molecular weight of TBL. The comparison with a naphthalene dispersant shows that TBL has a similar or better dispersing ability, and the large quantity of sulfonic groups engrafted in lignin molecules and the markedly increase of molecular weight are considered the key reason for the excellent performance of TBL. Moreover, the change of the molecular configuration from globular to flocculent in solution observed by TEM is also considered as an important reason for the excellent dispersing effect of TBL for CWS. 25 refs., 6 figs., 7 tabs.

Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills

Energy Technology Data Exchange (ETDEWEB)

Raza, M.; Jinyue Yan (Dept. of Chemical Engineering and Technology/Energy Processes, Royal Institute of Technology, Stockholm (Sweden)). e-mail: rnaqvi@kth.se; Froeling, Morgan (Dept. of Chemical and Biological Engineering, Chalmers Univ. of Technology, Goeteborg (Sweden))

2009-07-01

The consumption of fossil fuels is rapidly increasing and there is an urgent need to develop technologies for renewable fuel production not only as alternatives but also as additional fuels. Efficient polygeneration of transportation fuels with heat and electricity is one of the innovative technologies which have potential to replace fossil fuels and mitigate climate change. Two potential technologies of producing dimethyl ether (DME) and methane (CH4) as alternative fuels integrated with black liquor gasification have been studied and compared in this paper. System performance is evaluated based on: (i) Comparison with the reference pulp mill, (ii) Fuel to product efficiency (FTPE) and (iii) Biofuel Production Potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH4 production globally in terms of black liquor availability. BPP and FTPE of CH4 production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill

Energy efficiency improvement of a Kraft process through practical stack gases heat recovery

International Nuclear Information System (INIS)

Mostajeran Goortani, B.; Mateos-Espejel, E.; Moshkelani, M.; Paris, J.

2011-01-01

A process scheme for the optimal recovery of heat from stack gases considering energy and technical constraints has been developed and applied to an existing Kraft pulping mill. A system based on a closed loop recirculation of hot oil is used to recover the heat from stack gases and distribute it to the appropriate cold streams. The recovery of heat from stack gases is part of an overall optimization of the Kraft mill. Tools such as Pinch Analysis and exergy analysis are used to evaluate the process streams. The results indicate that 10.8 MW of heat from stack gases can be reused to heat process streams such as the deaerator water, hot water, drying filtrates, and black liquor. A simulation model of the recirculation loop has been developed to determine the specifications of the recovery system. The total heat exchanger surface area required by the system is 3460 m 2 , with a hot oil recirculation temperature of 137 o C. The anticipated total investment is $10.3 M, with a payback time of 1.8 years. - Highlights: → We developed a process design for recovering heat from stack gases in a Kraft mill. → The recovered heat is optimally distributed to the process cold streams. → Heat recovery system has a total surface area of 3500 m 2 without gases condensation. → A reduction of 7 percent in total process steam demand is anticipated. → A total investment of 10.3 M$ is needed with a payback time of less than two years

Co-gasification of black liquor and pyrolysis oil: Evaluation of blend ratios and methanol production capacities

International Nuclear Information System (INIS)

Andersson, Jim; Furusjö, Erik; Wetterlund, Elisabeth; Lundgren, Joakim; Landälv, Ingvar

2016-01-01

Highlights: • Biomethanol from co-gasified black liquor and pyrolysis oil at different capacities. • Enables higher biofuel production for given available amount of black liquor. • Opportunity for cost efficient black liquor gasification also in small pulp mills. • The methanol can be cost competitive to 2nd generation ethanol and fossil fuels. • Fewer pulp mills would need to be converted to meet given biofuel demand. - Abstract: The main aim of this study is to investigate integrated methanol production via co-gasification of black liquor (BL) and pyrolysis oil (PO), at Swedish pulp mills. The objectives are to evaluate techno-economically different blends ratios for different pulp mill capacities. Furthermore, the future methanol production potential in Sweden and overall system consequences of large-scale implementation of PO/BL co-gasification are also assessed. It is concluded that gasification of pure BL and PO/BL blends up to 50% results in significantly lower production costs than what can be achieved by gasification of unblended PO. Co-gasification with 20–50% oil addition would be the most advantageous solution based on IRR for integrated biofuel plants in small pulp mills (200 kADt/y), whilst pure black liquor gasification (BLG) will be the most advantageous alternative for larger pulp mills. For pulp mill sizes between 300 and 600 kADt/y, it is also concluded that a feasible methanol production can be achieved at a methanol market price below 100 €/MW h, for production capacities ranging between 0.9 and 1.6 TW h/y for pure BLG, and between 1.2 and 6.5 TW h/y for PO/BL co-gasification. This study also shows that by introducing PO/BL co-gasification, fewer pulp mills would need to be converted to biofuel plants than with pure BLG, to meet a certain biofuel demand for a region. Due to the technical as well as organizational complexity of the integration this may prove beneficial, and could also potentially lower the total investment

Comparison of Refractory Performance in Black Liquor Gasifiers and a Smelt Test System

International Nuclear Information System (INIS)

Peascoe, RA

2001-01-01

Prior laboratory corrosion studies along with experience at the black liquor gasifier in New Bern, North Carolina, clearly demonstrate that serious material problems exist with the gasifier's refractory lining. Mullite-based and alumina-based refractories used at the New Bern facility suffered significant degradation even though they reportedly performed adequately in smaller scale systems. Oak Ridge National Laboratory's involvement in the failure analysis, and the initial exploration of suitable replacement materials, led to the realization that a simple and reliable, complementary method for refractory screening was needed. The development of a laboratory test system and its suitability for simulating the environment of black liquor gasifiers was undertaken. Identification and characterization of corrosion products were used to evaluate the test system as a rapid screening tool for refractory performance and as a predictor of refractory lifetime. Results from the test systems and pl ants were qualitatively similar

Materials for the pulp and paper industry. Section 1: Development of materials for black liquor recovery boilers

Energy Technology Data Exchange (ETDEWEB)

Keiser, J.R.; Hubbard, C.R.; Payzant, E.A. [Oak Ridge National Lab., TN (United States)] [and others

1997-04-01

Black liquor recovery boilers are essential components of kraft pulp and paper mills because they are a critical element of the system used to recover the pulping chemicals required in the kraft pulping process. In addition, the steam produced in these boilers is used to generate a significant portion of the electrical power used in the mill. Recovery boilers require the largest capital investment of any individual component of a paper mill, and these boilers are a major source of material problems in a mill. The walls and floors of these boilers are constructed of tube panels that circulate high pressure water. Molten salts (smelt) accumulate on the floor of recovery boilers, and leakage of water into the boiler can result in a violent explosion when the leaked water instantly vaporizes upon contacting the molten smelt. Because corrosion of the conventionally-used carbon steel tubing was found to be excessive in the lower section of recovery boilers, use of stainless steel/carbon steel co-extruded tubing was adopted for boiler walls to lessen corrosion and reduce the likelihood of smelt/water explosions. Eventually, this co-extruded or composite (as it is known in the industry) tubing was selected for use as a portion or all of the floor of recovery boilers, particularly those operating at pressures > 6.2 MPa (900 psi), because of the corrosion problems encountered in carbon steel floor tubes. Since neither the cause of the cracking nor an effective solution has been identified, this program was established to develop a thorough understanding of the degradation that occurs in the composite tubing used for walls and floors. This is being accomplished through a program that includes collection and review of technical reports, examination of unexposed and cracked tubes from boiler floors, computer modeling to predict residual stresses under operating conditions, and operation of laboratory tests to study corrosion, stress corrosion cracking, and thermal fatigue.

Numerical modelling of the CHEMREC black liquor gasification process. Conceptual design study of the burner in a pilot gasification reactor

Energy Technology Data Exchange (ETDEWEB)

Marklund, Magnus

2001-02-01

The work presented in this report is done in order to develop a simplified CFD model for Chemrec's pressurised black liquor gasification process. This process is presently under development and will have a number of advantages compared to conventional processes for black liquor recovery. The main goal with this work has been to get qualitative information on influence of burner design for the gas flow in the gasification reactor. Gasification of black liquor is a very complex process. The liquor is composed of a number of different substances and the composition may vary considerably between liquors originating from different mills and even for black liquor from a single process. When a black liquor droplet is gasified it loses its organic material to produce combustible gases by three stages of conversion: Drying, pyrolysis and char gasification. In the end of the conversion only an inorganic smelt remains (ideally). The aim is to get this smelt to form a protective layer, against corrosion and heat, on the reactor walls. Due to the complexity of gasification of black liquor some simplifications had to be made in order to develop a CFD model for the preliminary design of the gasification reactor. Instead of modelling droplets in detail, generating gas by gasification, sources were placed in a prescribed volume where gasification (mainly drying and pyrolysis) of the black liquor droplets was assumed to occur. Source terms for the energy and momentum equations, consistent with the mass source distribution, were derived from the corresponding control volume equations by assuming a symmetric outflow of gas from the droplets and a uniform degree of conversion of reactive components in the droplets. A particle transport model was also used in order to study trajectories from droplets entering the reactor. The resulting model has been implemented in a commercial finite volume code (AEA-CFX) through customised Fortran subroutines. The advantages with this simple

Improvement of linerboard compressive strength by hot-pressing and addition of recovered lignin from spent pulping liquor

Directory of Open Access Journals (Sweden)

Saidan Motasem N.

2015-01-01

Full Text Available This paper evaluates the effect of addition of precipitated lignin, from spent pulping black liquor, to a wet single-ply linerboard handsheet followed by hot-pressing at different temperatures, on the improvement of its compressive strength. Linerboard handsheets for testing the effect of lignin addition were prepared so that the lignin-modified sheets would have the same basis weights as the control handsheets. Both the commercial and the black liquor lignin were added as a powder to wet handsheets after couching from the handsheet mold. The experiments and testing of the physical and strength properties of dried handsheets were conducted according to TAPPI test methods. The results revealed that the addition of the recovered lignin (at pH of 2 to the wet handsheet followed by hot-pressing at 150°C increased the compressive strength of linerboard handsheets by 10% to 20% above that for handsheets made without the addition of lignin. The same results were achieved using purchased lignin. However, with a 16% addition to linerboard, purchased lignin would be too expensive. These results indicate that inclusion of kraft lignin in linerboard sheets could be proved as an attractive option to reduce linerboard basis weight.

Influence of pressure on pyrolysis of black liquor: 2. Char yields and component release.

Science.gov (United States)

Whitty, Kevin; Kullberg, Mika; Sorvari, Vesa; Backman, Rainer; Hupa, Mikko

2008-02-01

This is the second in a series of papers concerning the behavior of black liquor during pyrolysis at elevated pressures. Two industrial black liquors were pyrolyzed under pressurized conditions in two laboratory-scale devices, a pressurized single-particle reactor and a pressurized grid heater. Temperatures ranging between 650 and 1100 degrees C and pressures in the range 1-20 bar were studied. Char yields were calculated and based on analysis of some of the chars the fate of carbon, sodium, potassium and sulfur was determined as a function of pyrolysis pressure. At temperatures below 800 degrees C little variation in char yield was observed at different pressures. At higher temperatures char yield increased with pressure due to slower decomposition of sodium carbonate. For the same reason, sodium release decreased with pressure. Sulfur release, however, increased with pressure primarily because there was less opportunity for its capture in the less-swollen chars.

System aspects of black liquor gasification - Consequences for both industry and society

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

The pulp and paper industry consumes large quantities of biofuels (mainly bark and black liquor) to satisfy process requirements. Biomass is however a limited resource, and biofuel usage should therefore be as effective as possible. Modern pulp mills and integrated pulp and paper mills have excess fuel compared to the amounts needed to satisfy the process steam demand. The excess fuel is often used for cogeneration of electric power in CHP units. For integrated pulp and paper mills, this usually requires import of supplementary fuel to the plant. For market pulp mills, the excess internal biofuel quantities are sufficient to also allow electric power generation in condensing power plant units. If biofuel availability at a reasonable price is limited, import/export to, from a mill changes the amount of such biofuel available to alternative users. The goal of this thesis is to compare different mill powerhouse technologies and CHP plant configurations (including conventional recovery boiler technology and black liquor gasification technology) in order to identify the technology and CHP plant configuration that can produce the most electric power output from a given fuel resource for a given process steam demand. Different process steam demand levels for different representative mill types are considered. The comparison accounts for increased/decreased electricity production in an alternative energy system when biofuel is imported/exported to/from from the mill. The alternative energy system considered includes a district heating system with CHP capacity and natural gas fired combined cycle power plant capacity. The results show that black liquor gasification is in all cases considered an attractive powerhouse recovery cycle technology compared to conventional recovery boiler technology. If the marginal electric power generation efficiency for biofuel exported to the reference alternative energy system is 49%, excess mill internal biofuel should be used on mill

A survey of present levels of radiocesium in Swedish pulp mill liquors and the implications for wood radiocesium transfer factors

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

1998-01-01

Assessments of the impact from radioactive fallout on the pulp industry and the accumulation processes for radionuclides in such industries, using wood and water as primary raw materials, have been conducted in previous studies. Hitherto, there is a general lack of data on present levels of radioactivity in pulp mill liquors apart from the few mills studied by [NILSSON (1992)] [RAVILA AND HOLM (1992)] [MANJON ET AL. (1996) and [KROSSHAVN ET AL. (1997)]. A survey was therefore initiated to describe and compare the present activity levels in pulp mill liquors from various mill locations in Sweden. The 137 Cs activity in pulp mill liquors were compared with the mill location and the deposition pattern of the Chernobyl fallout and nuclear weapons fallout. The large input of wood (approx. 2500 m 3 day -1 ) to an average Nordic Kraft mill and the relatively long-term retention time for radiocesium in the Kraft mill recovery cycle enables representative sampling of substances directly related to the activity concentration in wood

PROCESS FOR THE PRODUCTION OF DISSOLVING PULP FROM TREMA ORIENTALIS (NALITA) BY PREHYDROLYSIS KRAFT AND SODA-ETHYLENEDIAMINE (EDA) PROCESS

OpenAIRE

M. A. Quaiyyum; A. Noori; Labooni Ahsan; M. Sarwar Jahan

2008-01-01

This paper presents a preliminary study for the production of dissolving pulp from Trema orientalis (Nalita). Water prehydrolysis kraft and soda-ethylenediamine (EDA) pulping for the production of dissolving pulp from T. orientalis was investigated. Prehydrolysis at 150 and 170 oC did not produce pulp with high α-cellulose content when using the kraft process. But addition of 0.25 % H2SO4 in prehydrolysis liquor increased the purity of the pulp with the sacrifice of pulp yield and viscosity. ...

Recovering/concentrating of hemicellulosic sugars and acetic acid by nanofiltration and reverse osmosis from prehydrolysis liquor of kraft based hardwood dissolving pulp process.

Science.gov (United States)

Ahsan, Laboni; Jahan, M Sarwar; Ni, Yonghao

2014-03-01

This work investigated the feasibility of recovering and concentrating sugars and acetic acid (HAc) from prehydrolysis liquor (PHL) of the kraft-based dissolving pulp process prior to fermentation of hemicellulosic sugars, by the combination of activated carbon adsorption, nanofiltration (NF) and reverse osmosis (RO) processes. To reduce the fouling PHL was subjected to adsorption on activated carbon, then the treated PHL (TPHL) passed through a nanofiltration (NF DK) membrane to retain the sugars, and the permeate of acetic acid rich solution was passed through a reverse osmosis membrane (RO SG). It was found that for NF process sugars were concentrated from 48 to 227g/L at a volume reduction factor (VRF) of 5 while 80 to 90% of acetic acid was permeated. For the reverse osmosis process, 68% of acetic acid retention was achieved at pH 4.3 and 500 psi pressure and the HAc concentration increased from 10 to 50g/L. Crown Copyright © 2013. Published by Elsevier Ltd. All rights reserved.

Potential of Black Liquor of Potassium Hydroxide to Pretreat Corn Stover for Biomethane Production

Directory of Open Access Journals (Sweden)

Muhammad Abdul Hanan Siddhu

2016-04-01

Full Text Available Reducing the pretreatment cost of lignocellulosic biomass by utilizing alkali to alter its recalcitrant nature is an effective method for biofuel production. In this experiment, 1.5% KOH solution and its black liquor (spent liquor of KOH (BL were applied to pretreat corn stover (CS at a temperature of 20 °C to enhance the digestibility for anaerobic digestion (AD. Results showed no significant difference in weighted average methane content on the basis of experimental methane and biogas yields between BL-treated and original KOH-treated CS after AD. The BL process significantly increased the overall methane yield by 52.4% compared with untreated CS (135.2 mL/gVS, whereas no significant difference between the overall methane yields of 1.5% KOH-treated and BL-treated CS was observed. In addition, the BL process significantly saved water and KOH consumption, by 56.2% and 57.4%, respectively, compared with the 1.5% KOH pretreatment. Overall methane production was well explained by the modified Gompertz model. The physiochemical changes to CS after BL pretreatment were confirmed by SEM, FTIR, and XRD analyses. Our findings collectively suggest that recycling and reuse of KOH black liquor might be an efficient method for lignocellulosic biomass treatment and have the capability to reduce input costs in future AD processes.

Study on Effectiveness of Processed and Unprocessed Black Liquor pulps in improving the properties of PPC mortar, Concrete and SCC

Science.gov (United States)

Ananthkumar, M.; Sathyan, Dhanya; Prabha, B.

2018-02-01

The cost of construction materials is increasing day by day because of high demand, scarcity of raw materials and high price of energy. From the view point of energy saving and over consumption of resources, the use of alternative constituents in construction materials is now a global concern. From this, the extensive research and development works towards exploring new ingredients are required for producing sustainable and environment friendly construction materials. Bagasse pulp liquor is one such material that can be used as a chemical admixture which is obtained as a by-product of paper manufacturing process. Around 5 million tons of bagasse pulp is obtained throughout the world each year. since the material is a waste product from paper industry, this can be changed as a admixture by its effective use in concrete. In the present investigation black pulp liquor is added to fresh concrete in different dosages, the concrete is then tested for workability, compressive strength, flexural, split tensile strength and setting time. From results it is shown that 1% replacement of water with black pulp liquor increases the fresh properties of the concrete, 2% replacement of water with black pulp liquor increases the mechanical properties of the concrete and acts as a set retarder.

The effect of amphipilic lignin derivatives addition on enzymatic hydrolysis performance of kraft pulp from sorghum bagasse

Science.gov (United States)

Fatriasari, Widya; Nugroho Adi, D. T.; Laksana, R. P. B.; Fajriutami, T.; Raniya, R.; Ghozali, M.; Hermiati, E.

2018-03-01

Previously, the chemical characteristics of isolated lignin from Acacia mangium black liquor of kraft pulping was characterized. This lignin was blended with natural rubber latex (NR-L) as adhesive in laminated wood. In addition, lignin has potency for biosurfactant materials by modification of the hydrophobic into hydrophilic properties. Therefore, this study was intended to develop lignin as material for amphipilic lignin derivatives (A-LD) biosurfactant by reacting lignin with epoxilated polyethylene glicol (PEG). A-LD addition in slurries was used to improve the enzymatic hydrolysis (EH) of kraft pulp sweet bagasse sorghum (SSB). The main observation in EH performance was to investigate the effect of lignin isolation method (one and two step) in A-LD and A-LD loading addition on reducing sugar yield (RSY) of SSB kraft pulp. The pulp was hydrolyzed at 50°C and 150 rpm for 72 h with 10 FPU cellulase loading in the shaking incubator. A-LD from one (L1S) and two step (L2S) lignin was added with A-LD loading of 0, 1, 2, 5, and 10% (b/v). The RSY of hydrolyzate has been observed after EH. A-LDs addition in EH of SSB kraft pulp enhanced RSY. L1S worked better in reaction performance with PEDGE compared to L2S and LS. A better performance was showed by PEDGE 500 than that of PEDGE 6000. Generally, the higher A-LDs loading resulted higher RSY. The highest RSY (81.33%) was resulted in addition of 10% A-LD L1S using PEDGE 500. A 5% A-LD loading was more considered to be added in EH because the RSY was comparable with 10% A-LD loading.

System analysis of dry black liquor gasification based synthetic gas production comparing oxygen and air blown gasification systems

International Nuclear Information System (INIS)

Naqvi, Muhammad; Yan, Jinyue; Dahlquist, Erik

2013-01-01

Highlights: ► Circulating fluidized bed system for black liquor gasification with direct causticization. ► Effects of gasifying medium i.e. oxygen or air, on gasification are studied. ► Direct causticization eliminates energy intensive limekiln reducing biomass use. ► Results show 10% higher SNG production from O 2 blown system than air blown system. ► SNG production is higher in O 2 blown system than air blown system. - Abstract: The black liquor gasification based bio-fuel production at chemical pulp mill is an attractive option to replace conventional recovery boilers increasing system energy efficiency. The present paper studies circulating fluidized bed system with direct causticization using TiO 2 for the gasification of the black liquor to the synthesis gas. The advantage of using direct causticization is the elimination of energy-intensive lime kiln which is an integral part of the conventional black liquor recovery system. The study evaluates the effects of gasifying medium i.e. oxygen or air, on the fluidized bed gasification system, the synthesis gas composition, and the downstream processes for the synthesis gas conversion to the synthetic natural gas (SNG). The results showed higher synthetic natural gas production potential with about 10% higher energy efficiency using oxygen blown gasification system than the air blown system. From the pulp mill integration perspective, the material and energy balance results in better integration of air blown system than the oxygen blown system, e.g. less steam required to be generated in the power boiler, less electricity import, and less additional biomass requirement. However, the air blown system still requires a significant amount of energy in terms of the synthesis gas handling and gas upgrading using the nitrogen rejection system

Integration of the Mini-Sulfide Sulfite Anthraquinone (MSS-AQ) Pulping Process and Black Liquor Gasification in a Pulp Mill

Energy Technology Data Exchange (ETDEWEB)

Hasan Jameel, North Carolina State University; Adrianna Kirkman, North Carolina State University; Ravi Chandran,Thermochem Recovery International Brian Turk Research Triangle Institute; Brian Green, Research Triangle Institute

2010-01-27

As many of the recovery boilers and other pieces of large capital equipment of U.S. pulp mills are nearing the end of their useful life, the pulp and paper industry will soon need to make long-term investments in new technologies. The ability to install integrated, complete systems that are highly efficient will impact the industry’s energy use for decades to come. Developing a process for these new systems is key to the adoption of state-of-the-art technologies in the Forest Products industry. This project defined an integrated process model that combines mini-sulfide sulfite anthraquinone (MSS-AQ) pulping and black liquor gasification with a proprietary desulfurization process developed by the Research Triangle Institute. Black liquor gasification is an emerging technology that enables the use of MSS-AQ pulping, which results in higher yield, lower bleaching cost, lower sulfur emissions, and the elimination of causticization requirements. The recently developed gas cleanup/absorber technology can clean the product gas to a state suitable for use in a gas turbine and also regenerate the pulping chemicals needed to for the MSS-AQ pulping process. The combination of three advanced technologies into an integrated design will enable the pulping industry to achieve a new level of efficiency, environmental performance, and cost savings. Because the three technologies are complimentary, their adoption as a streamlined package will ensure their ability to deliver maximum energy and cost savings benefits. The process models developed by this project will enable the successful integration of new technologies into the next generation of chemical pulping mills. When compared to the Kraft reference pulp, the MSS-AQ procedures produced pulps with a 10-15 % yield benefit and the ISO brightness was 1.5-2 times greater. The pulp refined little easier and had a slightly lower apparent sheet density (In both the cases). At similar levels of tear index the MSS-AQ pulps also

Modelling, simulation, and optimisation of a downflow entrained flow reactor for black liquor gasification

Energy Technology Data Exchange (ETDEWEB)

Marklund, Magnus [ETC Energitekniskt Centrum, Piteaa (Sweden)

2003-12-01

Black liquor, a by-product of the chemical pulping process, is an important liquid fuel in the pulp and paper industry. A potential technology for improving the recovery cycle of energy and chemicals contained in the liquid fuel is pressurised gasification of black liquor (PGLG). However, uncertainties about the reliability and robustness of the technology are preventing a large-scale market introduction. One important step towards a greater trust in the process reliability is the development of simulation tools that can provide a better understanding of the process and improve performance through optimisation. In the beginning of 2001 a project was initiated in order to develop a simulation tool for an entrained-flow gasifier in PBLG based on CFD (Computational Fluid Dynamics). The aim has been to provide an advanced tool for a better understanding of process performance, to help with trouble shooting in the development plant, and for use in optimisation of a full-scale commercial gasifier. Furthermore, the project will also provide quantitative information on burner functionality through advanced laser-optical measurements by use of a Phase Doppler Anemometer (PDA). To this point in current project, three different concept models have been developed. The work has been comprised in a thesis 'Modelling and Simulation of Pressurised Black Liquor Gasification at High Temperature' and presented at Luleaa Univ. of Technology in Oct 2003. The construction of an atmospheric burner test rig has also been initiated. The main objective with the rig will be to quantify the atomisation performance of suitable burner nozzles for a PBLG gasifier that can be used as input for the CFD model. The main conclusions from the modelling work done this far can be condensed to the following points: From the first modelling results it was concluded that a wide spray pattern is preferable with respect to demand for long residence times for black liquor droplets and a low amount

Attenuated total reflection UV spectroscopy for simultaneous analysis of alkali, sulphide and dissolved lignin in pulping liquors

International Nuclear Information System (INIS)

Chai, X.S.; Zhu, J.Y.; Luo, Q.; Li, J.

2003-01-01

This study experimentally demonstrated attenuated total reflection (ATR) ultraviolet (UV) spectroscopy for rapid and simultaneous determination of the concentrations of hydroxide, sulphide and dissolved lignin in kraft pulping liquors. A multivariate partial least squares fitting procedure (using commercially available software) was employed to obtain the species concentrations from the measured absorption spectra of the pulping liquors. Good agreements between ATR-UV measured species concentrations and those obtained by reference methods (titration for hydroxide and sulphide and conventional UV absorption for dissolved lignin) were achieved. (author)

Comparison of two continuous fungal bioreactors for posttreatment of anaerobically pretreated weak black liquor from kraft pulp mills.

Science.gov (United States)

Ortega-Clemente, Alfredo; Marín-Mezo, G; Ponce-Noyola, M T; Montes-Horcasitas, M C; Caffarel-Méndez, S; Barrera-Cortés, Josefina; Poggi-Varaldo, Héctor M

2007-03-01

The purpose of this work was to evaluate and compare two continuous systems of posttreatment of anaerobically pretreated weak black liquor (WBL). The first system consisted of a packed bed reactor (PBR) with Trametes versicolor (Tv) immobilized on wood cubes of holm oak (biocubes). The second system was a fluidized bed reactor (FBR) with Lentinus edodes (Le) immobilized on wood cubes of holm oak. The reactors operated for 65 days at a hydraulic retention time (HRT) of 5 days, at 28 degrees C, with continuous aeration. Response variables monitored were conventional and specific, unit, net removal efficiency (eta and eta(sun), respectively) of chemical oxygen demand (COD), color, and ligninoids, and enzymatic activities of manganese peroxidase (MnP), lignin peroxidase (LiP), laccase (Lac) and proteases. The PBR showed an average color eta superior to that of the FBR (52.42 +/- 21.78% and 25.34 +/- 14.38% for PBR and FBR, respectively); removals of COD and ligninoids presented a similar pattern to that of color. Lac activity was significantly larger in PBR than in FBR. Activity of MnP in PBR was higher than that of the FBR (0.004 and 0.002 U MnP/mL, respectively). This difference could be ascribed to the different fungi present in each bioreactor. LiP activity was very low in both reactors. Average value of proteases was almost double in the FBR as compared with PBR (0.472 and 0.209 U Proteases/mL, respectively). During the last 2 weeks of operation, biocubes in the FBR experienced a significant loss of the attached Le biomass, probably by attrition. This and higher protease activity in the FBR could explain the lower pollutant removals achieved in the FBR. Overall, PBR with immobilized Tv showed a better performance than the FBR with Le for the posttreatment of the recalcitrant anaerobic effluent. Extended and sustained pollutant removal (65 days) was achieved in the PBR, although more research is needed to evaluate bioreactor performance at shorter hydraulic

The kinetics of the gasification of black liquor. Final report

Energy Technology Data Exchange (ETDEWEB)

Richards, Tobias; Theliander, Hans; Wintoko, Joko [Chalmers Univ. of Technology, Goeteborg (Sweden). Forest Products and Chemical Engineering

2004-05-01

Within the project, a special equipment has been manufactured in order to perform gasification experiments on single black liquor droplets. There are possibilities with the equipment to dynamically measure the weight of the droplet as well as its center temperature. Furthermore, some key gases (CO{sub 2}, CO, H{sub 2}S, CH{sub 4} and SO{sub 2}) are continuously measured. It is also possible to follow the gasification stages visually through a glass window. Parallel with this, a mathematical model has been developed to describe the gasification. It consists of both reaction kinetics and transport phenomenon. As a first step, the temperature profile was modeled and after that the model has been expanded to describe the swelling.

Simultaneous measurement of the surface temperature and the release of atomic sodium from a burning black liquor droplet

Energy Technology Data Exchange (ETDEWEB)

Saw, Woei L.; Nathan, Graham J. [Centre for Energy Technology, The University of Adelaide, SA 5006 (Australia); School of Mechanical Engineering, The University of Adelaide (Australia); Ashman, Peter J.; Alwahabi, Zeyad T. [Centre for Energy Technology, The University of Adelaide, SA 5006 (Australia); School of Chemical Engineering, The University of Adelaide (Australia); Hupa, Mikko [Process Chemistry Centre, Aabo Akademi, Biskopsgatan 8 FI-20500 Aabo (Finland)

2010-04-15

Simultaneous measurement of the concentration of released atomic sodium, swelling, surface and internal temperature of a burning black liquor droplet under a fuel lean and rich condition has been demonstrated. Two-dimensional two-colour optical pyrometry was employed to determine the distribution of surface temperature and swelling of a burning black liquor droplet while planar laser-induced fluorescence (PLIF) was used to assess the temporal release of atomic sodium. The key findings of these studies are: (i) the concentration of atomic sodium released during the drying and devolatilisation stages was found to be correlated with the external surface area; and (ii) the insignificant presence of atomic sodium during the char consumption stage shows that sodium release is suppressed by the lower temperature and by the high CO{sub 2} content in and around the particle. (author)

Black Liquor Gasification with Motor Fuel Production - BLGMF II - A techno-economic feasibility study on catalytic Fischer-Tropsch synthesis for synthetic diesel production in comparison with methanol and DME as transport fuels

Energy Technology Data Exchange (ETDEWEB)

Ekbom, Tomas; Berglin, Niklas; Loegdberg, Sara [Nykomb Synergetics AB, Stockholm (Sweden)

2005-06-15

The present project presents additional results to the former BLGMF project, which investigate Black Liquor Gasification with Motor Fuels (BLGMF) production. The objectives were to investigate, based on the KAM 2 program Ecocyclic Pulp Mill (2,000 ADt/day of pulp) the feasibility of synthetic fuels production. Specifically the route to Fischer-Tropsch diesel fuels is investigated as comparison to earlier work on methanol/DME. As modern kraft pulp mills have a surplus of energy, they could become key suppliers of renewable fuels. It is thus of great interest to convert the spent cooking product 'black liquor' to an energy carrier of high value. The resulting biomass-to-fuel energy efficiency when only biomass is used as an external energy source was 43% for FTD or 65% for FT products compared with 66% for methanol and 67% for DME. The FTD calculation is considerably more complicated and based on assumptions, therefore the uncertainty is higher. Would the diesel be taken out with a T95% of 320 deg C the FTD efficiency would be 45%. FT synthesis also opens up a possibility to produce e.g. lube oils from waxes produced. The total net FT-products output equals 4115 barrels/day. The FTD production cost is calculated as the energy share of the total production cost and assumes an offset of naphtha covering its own costs, where it is essential that it finds a market. Assuming same petrol (methanol) and diesel (DME, FTD) costs for the consumer the payback time were 2.6, 2.9 and 3.4 years with an IRR of 40%, 45% and 30%, respectively. In conclusion, there are necessary resources and potential for large-scale methanol (or DME, FTD) production and substantial economic incentive for making plant investments and achieving competitive product revenues.

Black liquor-derived carbonaceous solid acid catalyst for the hydrolysis of pretreated rice straw in ionic liquid.

Science.gov (United States)

Bai, Chenxi; Zhu, Linfeng; Shen, Feng; Qi, Xinhua

2016-11-01

Lignin-containing black liquor from pretreatment of rice straw by KOH aqueous solution was applied to prepare a carbonaceous solid acid catalyst, in which KOH played dual roles of extracting lignin from rice straw and developing porosity of the carbon material as an activation agent. The synthesized black liquor-derived carbon material was applied in catalytic hydrolysis of the residue solid from the pretreatment of rice straw, which was mainly composed of cellulose and hemicellulose, and showed excellent activity for the production of total reducing sugars (TRS) in ionic liquid, 1-butyl-3-methyl imidazolium chloride. The highest TRS yield of 63.4% was achieved at 140°C for 120min, which was much higher than that obtained from crude rice straw under the same reaction conditions (36.6% TRS yield). Overall, this study provides a renewable strategy for the utilization of all components of lignocellulosic biomass. Copyright © 2016 Elsevier Ltd. All rights reserved.

Aktivitas Ligninolitik Beberapa Jamur Aphyllophorales dan Kemampuannya Mendegradasi Lignin pada Lindi Hitam

Directory of Open Access Journals (Sweden)

Atria Martina

2016-03-01

Full Text Available Fourteen local isolate Aphyllophorales fungi were screened their ligninolytic activity. The isolate with highest ligninolytic activity was tested it capability to degrade kraft blackliquor lignin. The biodegradability of black liquor is low because the presence of lignin and lignin derivative in the wastewater. These fungal were screened for ligninolytic activity by decolorization on solid mediacontaining RBBR dye. The ability of the fungal strains to biodegrade kraft black liquor lignin was performed by submerged fermentation condition with agitation and incubation time as treatment. The solid culture result in 3 isolates had ligninolytic activity and Ganoderma sp.BTA1 gave the highest ligninolytic. Agitation and incubation time influenced ligninbiodegradation of blackliquor significantly. Optimum condition for lignin biodegradation was at 200 rpm during 25 days with lignin reduction was 45,786%.

Pyrolysis and auto-gasification of black liquor in presence of ZnO: An integrated process for Zn/ZnO nanostructure production and bioenergy generation

International Nuclear Information System (INIS)

Maciel, A.V.; Job, A.E.; Mussel, W.N.; Pasa, V.M.D.

2012-01-01

This study presents a new process for valorisation of black liquor into gases that are used to reduce ZnO and promote zinc nanosheet synthesis, besides energy generation. During the black liquor pyrolysis and auto-gasification, gases evolve, especially carbon monoxide, and promote ZnO reduction with Zn (v) release. The metal is condensed yielding zinc nanosheets, with partial surface re-oxidation in presence of carbon dioxide. The process was investigated at the micro scale using thermal analyses (TG/DTG/DTA) and the gases evolved were analysed by FTIR spectroscopy (TG/FTIR). The process was also studied in laboratory scale using a tubular electric furnace. The black liquor/ZnO mixture was placed at the quartz tube and the sample was heated to 900 °C at 10 °C/min, and the temperature was held at 900 °C for 1 h. The nanostructures growth was catalyst-free, without pressure reduction or a template, at temperatures lower than those required in the classical carbothermal reduction of ZnO with fossil carbon. The nanostructures were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and infrared spectroscopy (FTIR). One mechanism was presented in an attempt to explain the synthesis of Zn/ZnO nanosheets that are crystalline. This green and innovative process has potential use at the industry due to its operational conditions, low costs and technological importance of Zn and ZnO nanostructures. -- Graphical abstract: Display Omitted Highlights: ► Black liquor and ZnO mixture were submitted to a heat treatment until 900 °C. ► The black liquor suffered pyrolysis and auto-gasification. ► ZnO is reduced by CO yielding Zn v , that is condensed generating Zn/ZnO nanosheets. ► The nanostructures are characterized and a mechanism of reactions is presented. ► The new process can produce energy and nanostructures in large scale.

Energy conversion performance of black liquor gasification to hydrogen production using direct causticization with CO(2) capture.

Science.gov (United States)

Naqvi, M; Yan, J; Dahlquist, E

2012-04-01

This paper estimates potential hydrogen production via dry black liquor gasification system with direct causticization integrated with a reference pulp mill. The advantage of using direct causticization is elimination of energy intensive lime kiln. Pressure swing adsorption is integrated in the carbon capture process for hydrogen upgrading. The energy conversion performance of the integrated system is compared with other bio-fuel alternatives and evaluated based on system performance indicators. The results indicated a significant hydrogen production potential (about 141MW) with an energy ratio of about 0.74 from the reference black liquor capacity (about 243.5MW) and extra biomass import (about 50MW) to compensate total energy deficit. About 867,000tonnes of CO(2) abatement per year is estimated i.e. combining CO(2) capture and CO(2) offset from hydrogen replacing motor gasoline. The hydrogen production offers a substantial motor fuel replacement especially in regions with large pulp and paper industry e.g. about 63% of domestic gasoline replacement in Sweden. Copyright © 2012 Elsevier Ltd. All rights reserved.

Spectroscopic determination of anthraquinone in kraft pulping liquors using a membrane interface

Science.gov (United States)

X.S. Chai; X.T. Yang; Q.X. Hou; J.Y. Zhu; L.-G. Danielsson

2003-01-01

A spectroscopic technique for determining AQ in pulping liquor was developed to effectively separate AQ from dissolved lignin. This technique is based on a flow analysis system with a Nafion membrane interface. The AQ passed through the membrane is converted into its reduced form, AHQ, using sodium hydrosulfite. AHQ has distinguished absorption characteristics in the...

Recycling of Dilute Deacetylation Black Liquor to Enable Efficient Recovery and Reuse of Spent Chemicals and Biomass Pretreatment Waste

Directory of Open Access Journals (Sweden)

Xiaowen Chen

2018-06-01

Full Text Available Deacetylation/dilute alkaline pretreatment followed by mechanical refining (DMR has been proven as an effective process for biomass sugar liberation without severe chemical modification to lignin. Previous research has been focused on optimizing deacetylation conditions, reducing energy consumptions in mechanical refining, and improving sugar yields and titers in enzymatic hydrolysis. To successfully commercialize this process, another critical challenge is to develop a robust process to balance water usage, recover spent chemicals, and utilize waste carbons from the dilute deacetylation waste liquor. In this work, a new process modification and strategy is pioneered to recycle and reuse the weak black liquor (WBL in order to reduce water, chemical, and energy usage while increasing both inorganic and organic contents in the WBLto facilitate downstream processing. Results suggest that the accumulation did not lower acetyl and lignin removal in alkaline pretreatment, resulting in comparable sugar yields in enzymatic hydrolysis. Sodium and potassium were found to be the two most important inorganic compounds in the recycled WBL. Moreover, the accumulated sodium and phenolic compounds did not inhibit the downstream ethanol fermentation processes. Finally, techno-economic analysis (TEA showed a decrease in the minimum ethanol selling price (MESP by ~5 to 15 cents per gallon of ethanol resulting from the inclusion of the recycling of weak black liquor when compared to a conventional non-recycling process.

Combustion oil production by direct liquefaction of the black liquor; Obtencao de oleo combustivel atraves da liquefacao direta de lixivia negra

Energy Technology Data Exchange (ETDEWEB)

Costa, J L.M. [Universidade Estadual de Maringa, PR (Brazil). Dept. de Quimica; Rodrigues, J A.R.; Schuchardt, U [Universidade Estadual de Campinas, SP (Brazil). Inst. de Quimica

1985-12-31

A large number of publications about the liquefaction of carbonaceous materials with carbon monoxide in water have appeared. As carbon monoxide reacts with water to form formate. We have decided to use this compound for the direct liquefaction of black liquor, obtained from the pulp and paper industry. The reactions were performed in a stainless steel autoclave of 1 litre using a ratio of water/black liquor/sodium formate of 69/29,5/1,5 %. The reaction conditions were varied between 200 and 300 deg C and 110 to 130 bar of inert gas. We obtained heavy oils of an average molecular weight around 500 in 90 to 100 % yield on a dry and ash-free basis. The calorific value of this oil was estimated in 38000 kJ/kg. (author). 12 refs., 2 figs., 7 tabs

Synthesis and characterization of high photocatalytic activity and stable Ag3PO4/TiO2 fibers for photocatalytic degradation of black liquor

International Nuclear Information System (INIS)

Cai, Li; Long, Qiyi; Yin, Chao

2014-01-01

Highlights: • Ag 3 PO 4 /TiO 2 fibers were prepared via in situ Ag 3 PO 4 particles onto the surface of TiO 2 fiber. • Ag 3 PO 4 /TiO 2 fibers have stronger catalytic activity and excellent chemical stability. • Ag 3 PO 4 /TiO 2 fibers act as an efficient catalyst for the photocatalytic degradation of black liquor. - Abstract: The TiO 2 fiber was prepared by using cotton fiber as a template, and then Ag 3 PO 4 /TiO 2 fibers were synthesized via in situ Ag 3 PO 4 particles onto the surface of TiO 2 fiber. Their structure and physical properties were characterized by means of scanning electron microscopy (SEM), specific surface analyzer, X-ray diffraction (XRD), UV–vis absorption spectra and photoluminescence spectra (PL). SEM analysis indicated that the well-defined surface morphology of natural cotton fiber was mostly preserved in TiO 2 and Ag 3 PO 4 /TiO 2 fibers. Compared with TiO 2 fiber, the absorbance wavelengths of Ag 3 PO 4 /TiO 2 fibers were apparently red shifted and the PL intensities revealed a significant decrease. By using the photocatalytic degradation of black liquor as a model reaction, the visible light and ultraviolet light catalytic efficiencies of TiO 2 , Ag 3 PO 4 and Ag 3 PO 4 /TiO 2 fibers were evaluated. The reaction results showed that Ag 3 PO 4 /TiO 2 fibers had stronger photocatalytic activity and excellent chemical stability in repeated and long-term applications. Therefore, the prepared Ag 3 PO 4 /TiO 2 fibers could act as an efficient catalyst for the photocatalytic degradation of black liquor, which suggested their promising applications. It was proposed that the • OH radicals played the leading role in the photocatalytic degradation of the black liquor by Ag 3 PO 4 /TiO 2 fibers system

Residual liquors of the pulp industries. 1. Lignohemicelluloses and silica from soda black liquors used as adjuvants in the manufacture of compact paper board

Energy Technology Data Exchange (ETDEWEB)

El-Saied, H; Nada, A A.M.; Ibrahem, A A

1982-01-01

Lignohemicellulosic materials and SiO/sub 2/ were recovered from black liquors from the pulping of rice straw. The lignohemicellulose improved the properties of compact cardboard from cotton stalk pulp more effectively than those of cardboard from rice straw pulp, while the effectiveness of the SiO/sub 2/ was in the opposite direction. The water resistance of cardboard from cotton stalk pulp made it suitable for both outdoor and indoor use, while cardboard from rice straw pulp could be used only indoors. The lignohemicellulose and SiO/sub 2/ could effectively replace more expensive phenolic resins in cardboard manufacture.

Fuel conversion characteristics of black liquor and pyrolysis oil mixture for efficient gasification with inherent catalyst

OpenAIRE

Bach Oller, Albert; Furusjö, Erik; Umeki, Kentaro

2014-01-01

This paper describes the technical feasibility of a catalytic co-gasification process using a mixture of black liquor (BL) and pyrolysis oil (PO). A technical concern is if gasifiers can be operated at low temperature (~1000 ºC) without problems of tar, soot or char, as is the case for pure BL due to the catalytic effect of fuel alkali. Hence, we investigated fuel conversion characteristics of BL/PO mixture: conversion of single droplet in flame, and char gasification reactivity. 20wt.% (BP20...

THE PROPERTIES OF CHARCOAL FROM THE BLACK LIQUOR OF THE SODA PULPING OF RICE STRAW

Directory of Open Access Journals (Sweden)

Nyoman Jaya Wistara

2013-11-01

Full Text Available The main goal of the present works was to determine chemical changes, thermal decomposition, and the content of moisture, ash, volatile, fixed carbon and calorific value of soda pulping black liquor of the rice straw. Neutralized black liquor was dried to a moisture content of 10% and then pyrolized at 106oC-750oC. It was found that calorific value, fixed carbon, volatile mater, and moisture content were in the range of 2782-4716 cal/g, 49.2-81.6%, 15.5-47.5%, and 0.2-3.5%, respectively. Ash content was not influenced by the temperature of pyrolysis and was thought to depend on its initial silicate content. The weight loss of pulp was higher than that of black liquor. Extreme weight loss has been found in the temperature of 200-400oC. Noticeable functional groups changes were found with the increasing temperature of pyrolysis. Hydroxyl group completely disappeared at 300oC and above. Carbonyl related groups were also disappeared at 300-500oC, but it was reformed at 650 and 750oC. It might be brought about by the deformation of chemical bonding of oxygen ring in lignin structures. SIFAT-SIFAT ARANG LINDI HITAM DARI PEMASAKAN JERAMI DENGAN LARUTAN SODA API. Penelitian ini bertujuan untuk menentukan perubahan sifat kimia, dekomposisi termal dan kadar air, abu, zat terbang, karbon terikat serta nilai kalor arang lindi hitam pemasakan soda jerami padi. Dalam penelitian ini, lindi hitam netral dikeringkan (kadar air 10%, kemudian dipirolisis pada selang suhu 100-750oC di dalam reaktor berpengatur suhu. Hasil penelitian menunjukkan bahwa nilai kalor, karbon terikat, zat terbang dan kadar air masing-masing berselangdari 2782-4716 cal/g, 49,2-81,6%, 15,5-47,5%, dan 0,2-3,5%. Kadar abu tidak dipengaruhi oleh suhu pirolisis dan diduga bergantung pada kadar silika bahan bakunya. Nilai kalor meningkat dengan meningkatnya kadar karbon terikat. Perilaku kehilangan berat arang dari lindi hitam berbeda dengan perilaku kehilangan berat pulp jerami. Kehilangan

Yield-increasing additives in kraft pulping: Effect on carbohydrate retention, composition and handsheet properties

Energy Technology Data Exchange (ETDEWEB)

Vaaler, David Andre Grimsoeen

2008-07-01

In this thesis, increased hemicellulose retention during kraft pulping has been studied. The work has been divided into three parts: i) Development of an accessible and reliable method for determination of carbohydrate composition of kraft pulps ii) Investigation of the composition and molecular mass distributions of the carbohydrates in kraft pulps with increased hemicellulose content iii) Investigation of the effect of increased hemicellulose content on the sheet properties of kraft pulps with increased hemicellulose content. A method for carbohydrate determination was developed. In this method, enzymes are used to hydrolyse the pulp into monosaccharides. A relatively mild acid hydrolysis is performed prior to detection on an HPLC with an RI-detector. The pulp is not derivatized and no pre-treatment (mechanical or chemical) is needed to determine the carbohydrate composition using the method developed here. Peak deconvolution software is used to improve the accuracy. Polysulphide and H2S primarily increase the glucomannan yield, which can be boosted by up to 7 % on o.d. wood. However, the cellulose yield is more affected by the cooking time and the maximum yield increase of cellulose is approximately 2 % on o.d. wood compared to an ordinary kraft pulp. The cooking time is influenced by sulphide ion concentration, AQ addition and the final Kappa number. The xylan yield is remarkably stable, however the alkali profile during the cook may influence the xylan yield. Surface xylan content of the fibres depends on residual alkali concentration in the black liquor. The molecular mass distributions of cellulose and hemicellulose were determined for pulps with increased hemicellulose content using size exclusion chromatography. Deconvolution by peak separation software is used to gain information about the degree of polymerization for cellulose and hemicellulose. The average DP of glucomannan in the kraft fibre was found to be 350 +- 30 and the average DP of xylan in the

Feasibility of reusing the black liquor for enzymatic hydrolysis and ethanol fermentation.

Science.gov (United States)

Wang, Wen; Chen, Xiaoyan; Tan, Xuesong; Wang, Qiong; Liu, Yunyun; He, Minchao; Yu, Qiang; Qi, Wei; Luo, Yu; Zhuang, Xinshu; Yuan, Zhenhong

2017-03-01

The black liquor (BL) generated in the alkaline pretreatment process is usually thought as the environmental pollutant. This study found that the pure alkaline lignin hardly inhibited the enzymatic hydrolysis of cellulose (EHC), which led to the investigation on the feasibility of reusing BL as the buffer via pH adjustment for the subsequent enzymatic hydrolysis and fermentation. The pH value of BL was adjusted from 13.23 to 4.80 with acetic acid, and the alkaline lignin was partially precipitated. It deposited on the surface of cellulose and negatively influenced the EHC via blocking the access of cellulase to cellulose and adsorbing cellulase. The supernatant separated from the acidified BL scarcely affected the EHC, but inhibited the ethanol fermentation. The 4-times diluted supernatant and the last-time waste wash water of the alkali-treated sugarcane bagasse didn't inhibit the EHC and ethanol production. This work gives a clue of saving water for alkaline pretreatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Sacrificial adsorbate for surfactants utilized in chemical floods of enhanced oil recovery operations

Science.gov (United States)

Johnson, Jr., James S.; Westmoreland, Clyde G.

1982-01-01

The present invention is directed to a sacrificial or competitive adsorbate for surfactants contained in chemical flooding emulsions for enhanced oil recovery operations. The adsorbate to be utilized in the method of the present invention is a caustic effluent from the bleach stage or the weak black liquor from the digesters and pulp washers of the kraft pulping process. This effluent or weak black liquor is injected into an oil-bearing subterranean earth formation prior to or concurrent with the chemical flood emulsion and is adsorbed on the active mineral surfaces of the formation matrix so as to effectively reduce adsorption of surfactant in the chemical flood. Alternatively, the effluent or liquor can be injected into the subterranean earth formation subsequent to a chemical flood to displace the surfactant from the mineral surfaces for the recovery thereof.

Adsorption of lignocelluloses of model pre-hydrolysis liquor on activated carbon.

Science.gov (United States)

Fatehi, Pedram; Ryan, Jennifer; Ni, Yonghao

2013-03-01

The main objective of this work was to study the adsorption behavior of various components dissolved in the pre-hydrolysis of kraft process on activated carbon. In this work, model prehydrolysis liquor (PHL) solutions (MPHL)s were prepared via mixing various commercially available monosugars, xylan, lignin and furfural; and their adsorption performance on activated carbon (AC) was investigated. In singular (one component) MPHL/AC systems, furfural had the maximum and xylose had the minimum adsorption, and the adsorption of monosugars was basically similar on AC. Also, polydiallyldimethylammonium chloride (PDADMAC) was added (0.5 g/l) to singular xylan or lignin MPHL/AC system, which increased the lignin and xylan adsorptions to 350 and 190 mg/g on AC, respectively. Copyright © 2012 Elsevier Ltd. All rights reserved.

Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

Energy Technology Data Exchange (ETDEWEB)

Lundqvist, Roland

2005-12-15

Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result in lime mud difficult to dewater, has not become true. Important experiences have come out which could be used as a base in further investigations.

Green liquor impregnation and Kraft pulping of South African Pinus Patula – “A practical approach to provide cost savings in a Kraft mill’s pulping operation”

CSIR Research Space (South Africa)

Johakimu, Jonas K

2011-02-01

Full Text Available . Singh J., Ragauskas A.R., Lucia L.A., (2002). ?Green Liquor Chip Pre- treatment as a Feasible Method for the Enhancement of Softwood Pulp Chemical Properties. Journal of wood Chemistry and Technology. 2: 173-181. 5. Gordon Broderick...

Development of a combined piezoresistive pressure and temperature sensor using a chemical protective coating for Kraft pulp digester process monitoring

International Nuclear Information System (INIS)

Mohammadi, Abdolreza R; Chiao, Mu; Bennington, Chad P J

2011-01-01

We have developed an integrated piezoresistive pressure and temperature sensor for multiphase chemical reactors, primarily Kraft pulp digesters (pH 13.5, temperatures up to 175 °C, reaching a local maximum of 180 °C and pressures up to 2 MPa). The absolute piezoresistive pressure sensor consisted of a large square silicon diaphragm (1000 × 1000 µm 2 ) and high resistance piezoresistors (10 000 Ω). A 4500 Ω buried piezoresistive wire was patterned on the silicon chip to form a piezoresistive temperature sensor which was used for pressure sensor compensation and temperature measurement. A 4 µm thick Parylene HT® coating, a chemically resistant epoxy and a silicone conformal coating were deposited to passivate the pressure sensor against the caustic environment in Kraft digesters. The sensors were characterized up to 2 MPa and 180 °C in an environment chamber. A maximum thermal error of ±0.72% full-scale output (FSO), an average sensitivity of 0.116 mV (V kPa) −1 and a power consumption of 0.3 mW were measured in the pressure sensor. The sensors' resistances were measured before and after test in a Kraft pulping cycle and showed no change in their values. SEM pictures and topographical surfaces were also analyzed before and after pulp liquor exposure and showed no observable changes.

78 FR 31315 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-05-23

... Kraft Pulp Mills NSPS Review; Proposed Rule #0;#0;Federal Register / Vol. 78 , No. 100 / Thursday, May...-OAR-2012-0640; FRL-9815-9] RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection... performance standards for kraft pulp mills. These revised standards include particulate matter emission limits...

REPLACEMENT OF SOFTWOOD KRAFT PULP WITH ECF-BLEACHED BAMBOO KRAFT PULP IN FINE PAPER

Directory of Open Access Journals (Sweden)

Guanglei Zhao

2010-06-01

Full Text Available Non-wood fibers such as bamboo and wheat straw have been playing important roles in the pulp and paper industry in China. In this study an ECF-bleached bamboo kraft pulp was compared with a bleached softwood kraft pulp (NBSK as the reinforcement pulp in fine paper production. Areas that were examined include the refining of pure fibers, influence of bamboo on dewatering, retention, and sizing. The influence of bamboo kraft pulp as a part of a furnish replacing NBSK was compared as well. Results show that fiber shortening was more prominent with bamboo when refined. This resulted in a higher amount of fines, and addition wet-end chemicals may be required to compensate. Handsheets with bamboo as a reinforcement fiber showed similar mechanical and optical properties to handsheets containing NBSK.

Removal of sulfite liquor from digesters with partially diluted liquor

Energy Technology Data Exchange (ETDEWEB)

Leshchenko, I G; Sykol, V P

1957-01-01

The yield of reducing sugars was raised from 189 to 224 kg/ton of pulp by displacing the cooking liquor with diluted liquor. As the pressure during blow-off dropped to 3.5-3.0 atmosphere, weak sulfite liquor was added at the rate 120 cu m/hr. After 5-10 minutes the liquor was pumped from the digester to the ethanol plant.

Sulfate reduction and carbon removal during kraft char burning

Energy Technology Data Exchange (ETDEWEB)

Waag, K.J.; Frederick, W.J.; Sricharoenchaikul, V [Oregon State Univ., Corvallis, OR (United States). Dept. of Chemical Engineering; Grace, T.M. [T.M. Grace Company, Appleton, WI (United States); Kymalainen, M. [Tampella Power, Tampere (Finland)

1995-12-31

An improved mathematical model of char burning during black liquor combustion was described. Enhancements include a proper treatment of CO{sub 2} and H{sub 2}O gasification, reactions between oxygen and combustibles in the boundary layer, and integration of sulfate reduction and sulfide reoxidation into the char burning process. Gasification of char carbon by reaction with H{sub 2}O and CO{sub 2} proved to be the most important means of carbon release under typical recovery furnace conditions. Sulfate reduction was shown to be responsible for only a minor part of the carbon release. Simulations showed that for typical recovery boiler conditions, char burning behavior is independent of oxygen concentration up to the point of carbon depletion. After carbon depletion, sulfide reoxidation occurs at a rate determined by oxygen mass transfer. Process variables that had the biggest effect on char burning behavior were initial black liquor drop diameter and temperature; also there was a direct link between char burnout times and the amount of sulfate reduction. At a given temperature, any variable that shortened the char burnout time resulted in proportionately less reduction. 22 refs., 10 figs., 2 tabs.

Effect of type of fungal culture, type of pellets and pH on the semi-continuous post-treatment of an anaerobically-pretreated weak black liquor from kraft pulp industry

Energy Technology Data Exchange (ETDEWEB)

Robledo-Narvaez, P. N.; Ortega-Clemente, L. A.; Ponce-Noyola, M. T.; Rinderknecht-Seijas, N. F.; Poggi-Varaldo, H. M.

2009-07-01

It is well known that fungi belonging to the Basidiomycetes (such as Trametes versicolor, Lentinus edodes, Phanerochaete chrysosporium) are microorganisms with a demonstrated capability of degrading lignin and its derivatives using a powerful and diverse group of enzymes. Because of these features, ligninolytic fungi have been used for the treatment or post-treatment of a variety of recalcitrant and toxic effluents, those of the Kraft industry among them. Yet, most of reported fungal treatments so far required the supplementation with glucose or other soluble carbohydrates, pH 4 to 4,5, and their effective performance was demonstrated only for short periods of operation time. (Author)

Preparation and Characterization of K2CO3-Activated Kraft Lignin Carbon

Directory of Open Access Journals (Sweden)

Xian-fa Li

2016-01-01

Full Text Available A series of activated carbons (ACs were prepared by K2CO3 activation from kraft lignin (KL that was recovered from papermaking black liquor. The effects of process parameters such as the activation temperature (AT, activated period, K2CO3 to KL mass ratio, and N2 flow rate on the characteristics of the final product were determined. The ACs were characterized using nitrogen adsorption, morphology, and fractal dimension analyses. The results showed that the AT was the main factor influencing the yield, surface area, and pore structure. The yield of ACs obviously decreased from 50.6% to 20.5% with increasing AT from 600 °C to 1000 °C, and decreased with increasing K2CO3/KL mass ratio. Activation time and N2 flow rate had slight effect on the yield of ACs. The surface area and total pore volume increased as the AT rose to 900 °C and then decreased with further increases in temperature. The maximum surface area and total pore volume were 1816.3 m2/g and 1.26 cm3/g, respectively, at a K2CO3 to KL mass ratio of 3:1, AT of 900 °C, activation time of 2 h, and N2 flow rate of 70 cm3/min. The pore structure of the ACs could be tailored by controlling the AT. As the AT was increased from 700 to 1000 °C, the mesoporosity increased from 11.6% to 95.9%. SEM images indicated that the morphology of ACs was modified by the AT. The K2CO3 was partially recycled.

Correlation of Process Data and Electrochemical Noise to Assess Kraft Digester Corrosion: Kamloops Experiment

Energy Technology Data Exchange (ETDEWEB)

Pawel, SJ

2002-05-09

Electrochemical noise (ECN) probes were deployed in a carbon steel continuous kraft digester at five locations roughly equi-spaced from top to bottom of the vessel. Current and potential noise, the temperature at each probe location, and the value of about 60 process parameters (flow rates, liquor chemistry, etc.) were monitored continuously for a period of one year. Historical vessel inspection data, including inspections accomplished immediately prior to and immediately following probe deployment, and post-test evaluation of the probe components were used to assess/compare corrosion indications from the probes with physical changes in wall thickness and corrosion patterns on the digester shell. The results indicate that furnish composition is a significant variable influencing digester corrosion, with increasing amounts of Douglas fir in the nominal furnish correlating directly with increased corrosion activity on the ECN probes. All five probes detected changes in furnish composition approximately simultaneously, indicating rapid chemical communication through the liquor, but the effect was strongest and persisted longest relatively high in the digester. The ECN probes also indicate significant corrosion activity occurred at each probe position during shutdown/restart transients. Little or no correlation between ECN probe corrosion activity and other operational variables was observed. Post-test evaluation of the probes confirmed general corrosion of a magnitude that closely agreed with corrosion current sums calculated for each probe over the exposure period and with historical average corrosion rates for the respective locations. Further, no pitting was observed on any of the electrodes, which is consistent with the ECN data, relevant polarization curves developed for steel in liquor removed from the digester, and the post-test inspection of the digester.

Liquor circulation disturbance after subarachnoid haemorrhages - comparative pneumoencephalography and liquor scintigraphic investigations

International Nuclear Information System (INIS)

Menzel, J.; Georgi, P.; Krastel, A.; Deutsches Krebsforschungszentrum, Heidelberg

1976-01-01

Haemorrhages into the subarachnoid space often lead to instant blocking of the liquor circulation pathways with an acute increase of the intracranial pressure and acute venticular enlargement. These liquor circulation disturbances may be diagnosed by liquor scintiscanning as well as by pneumoencephalography. 165 patients were examined by both methods. The following results were obtained: liquor circulation disturbances after subarachnoid bleeding are frequent, they should be expected in 33% of all cases after spontaneous subarachnoid haemorrhages and in 68% of the cases after traumatic subarachnoid haemorrhages. The most severe form of liquor circulation distrubance may also be diagnosed by liquor scintiscanning as well as by pneumoencephalography. Liquor scintiscanning is the more exact method in cases with transitory ventricular reflux, while lumbar pneumoencephalography, in this series, is the method of choice when it comes to documenting the extent of the hydrocephalus. (GSE) [de

Black liquor devolatilization and swelling - a detailed droplet model and experimental validation

International Nuclear Information System (INIS)

Jaervinen, M.; Zevenhoven, R.; Vakkilainen, E.; Forssen, M.

2003-01-01

In this paper, we present results from a new detailed physical model for single black liquor droplet pyrolysis and swelling, and validate them against experimental data from a non-oxidizing environment using two different reactor configurations. In the detailed model, we solve for the heat transfer and gas phase mass transfer in the droplet and thereby, the intra-particle gas-char and gas-gas interactions during drying and devolatilization can be studied. In the experimental part, the mass change, the swelling behaviour, and the volume fraction of larger voids, i.e. cenospheres in the droplets were determined in a non-oxidizing environment. The model gave a good correlation with experimental swelling and mass loss data. Calculations suggest that a considerable amount of the char can be consumed before the entire droplet has experienced the devolatilization and drying stages of combustion. Char formed at the droplet surface layer is generally consumed by gasification with H 2 O flowing outwards from the droplet interior. The extent of char conversion during devolatilization and the rate of devolatilization are greatly affected by swelling and the formation of larger voids in the particle. The more the particle swells and the more homogeneous the particle structure is, the larger is the conversion of char at the end of devolatilization

VOC Control in Kraft Mills; FINAL

International Nuclear Information System (INIS)

Zhu, J.Y.; Chai, X.-S.; Edwards, L.L.; Gu, Y.; Teja, A.S.; Kirkman, A.G.; Pfromm, P.H.; Rezac, M.E.

2001-01-01

The formation of volatile organic compounds (VOCs), such as methanol, in kraft mills has been an environmental concern. Methanol is soluble in water and can increase the biochemical oxygen demand. Furthermore, it can also be released into atmosphere at the process temperatures of kraft mill-streams. The Cluster Rule of the EPA now requires the control of the release of methanol in pulp and paper mills. This research program was conducted to develop a computer simulation tool for mills to predict VOC air emissions. To achieve the objective of the research program, much effort was made in the development of analytical techniques for the analysis of VOC and determination of vapor liquid partitioning coefficient of VOCs in kraft mill-streams using headspace gas chromatography. With the developed analytical tool, methanol formation in alkaline pulping was studied in laboratory to provide benchmark data of the amount of methanol formation in pulping in kraft mills and for the validation of VOC formation and vapor-liquid equilibrium submodels. Several millwide air and liquid samplings were conducted using the analytical tools developed to validate the simulation tool. The VOC predictive simulation model was developed based on the basic chemical engineering concepts, i.e., reaction kinetics, vapor liquid equilibrium, combined with computerized mass and energy balances. Four kraft mill case studies (a continuous digester, two brownstock washing lines, and a pre-evaporator system) are presented and compared with mill measurements. These case studies provide valuable, technical information for issues related to MACT I and MACT II compliance, such as condensate collection and Clean-Condensate-Alternatives (CCA)

Efficient exfoliation of layered materials by waste liquor

Science.gov (United States)

Ding, Jiheng; Zhao, Hongran; Zheng, Yan; Wang, Qiaolei; Chen, Hao; Dou, Huimin; Yu, Haibin

2018-03-01

Based on their unique material properties, two-dimensional (2D) nanomaterials such as graphene, molybdenum disulfide (MoS2), and boron nitride (BN) have been attracting increased research interest. The potential of 2D materials, in the form of nanoplatelets that are used as new materials, will be important to both nanomaterials and advanced materials. Water is usually considered to be the ideal dispersed medium, and the essential hydrophobicity and limitations to mass production of 2D nanoplatelets have become quite serious obstacles to their usage in various fields. In this paper, pulping black liquor was used as dispersant, with high concentration of lignin to get single- and few-layered nanoplatelets. The whole process required only the high-shear mixing of 2D layered materials and pulping waste liquor. This method was not only simple and efficient but also environmentally friendly and resource-recycling. Moreover, the fabricated single- or few-layered nanoplatelets possessed good solubility in aqueous solution due to their edge functionalization, and could be well dispersed in water at concentrations (10 mg ml-1 for graphene, 6.3 mg ml-1 for MoS2, and 6.0 mg ml-1 for BN) which were much higher than that of other methods. The dispersions of graphene, MoS2, and BN nanosheets were highly stable over several months, which allowed us to easily prepare graphene, MoS2, and BN films through simple vacuum filtration or spraying. These results indicated that pulping black liquor can be used as a material or reagent, and the mass production of 2D material is possible in a simple and fast method.

Kraft cooking of gamma irradiated wood, (1)

International Nuclear Information System (INIS)

Inaba, Masamitsu; Meshitsuka, Gyosuke; Nakano, Junzo

1979-01-01

Studies have been made of kraft cooking of gamma irradiated wood. Beech (Fagus crenata Blume) wood meal suspended in aqueous alkaline alcohol was irradiated up to 1.5 KGy (0.15 Mrad) with gamma rays from a Co-60 source in the presence or absence of oxygen. The irradiated wood meals were washed thoroughly with fresh water, air dried and cooked under the ordinary cooking conditions. The results are summarized as follows: (1) Pre-irradiation in aqueous alkali have negligible effect on kraft cooking. (2) In the case of ethanol addition (50 g/l), pre-irradiation in vacuo shows acceleration of delignification and stabilization of carbohydrates during kraft cooking. Cooked yield gain by pre-irradiation was about 1.2% in all over the range of delignification from 80 to 90%. Aqueous ethanol without alkali also shows positive but smaller effect than that with alkali. (3) Propanol, iso-propanol and butanol show positive but smaller effects than ethanol. However, methanol does not show any positive effect. (4) Irradiation in the presence of oxygen does not show any attractive effect on kraft cooking. (author)

Toxic waste liquor disposal

International Nuclear Information System (INIS)

Burton, W.R.

1985-01-01

Toxic waste liquors, especially radio active liquors, are disposed in a sub-zone by feeding down a bore hole a first liquid, then a buffer liquid (e.g. water), then the toxic liquors. Pressure variations are applied to the sub-zone to mix the first liquid and liquors to form gels or solids which inhibit further mixing and form a barrier between the sub-zone and the natural waters in the environment of the sub-zone. In another example the location of the sub-zone is selected so that the environement reacts with the liquors to produce a barrier around the zone. Blind bore holes are used to monitor the sub-zone profile. Materials may be added to the liquor to enhance barrier formation. (author)

Hygroscopic slaking of lime with steam or humid air. New energy effective lime slaking technology in kraft pulping; Hygroskopisk slaeckning av kalk med aanga eller fuktig luft. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

Energy Technology Data Exchange (ETDEWEB)

Lundqvist, Roland

2003-07-15

Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional slaking method is that heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant. The forecasted method means that lime is slaked with steam or humid air, for example combined with a lime mud drier and a lime kiln. The task has included slaking of burned lime with steam or humid hot air, on purpose to test a specific machine equipment in pilote scale, and to investigate temperatures and hydratization rates able to reach. Also the lime slaked with steam/humid air should be compared with burned lime slaked in green liquor when green liquor is causticized, and to investigate the dewatering properties of formed lime mud. The target group is pulp and paper industry using the kraft process. The tests have been performed at SMA Svenska Mineral AB plant (lime burning) at Sandarne Sweden in years 2004-2005. Project owner has been the Swedish company Torkapparater AB, and the project is performed inside the 'Vaermeforsk Program for Pulp and Paper Industry 2004-2005'. Other partners, besides SMA Svenska Mineral AB, has been Stora Enso Skoghalls Bruk, Carnot AB, AaF Process AB and KTH Energiprocesser. Hydrated lime of varying slaking rates has been produced at temperatures up to 270 deg C. Caustizicing being performed show that dewatering properties of lime mud formed is quite up to the standard of lime mud from burned lime slaked in green liquor. The apprehension, that the hygroscopic slaked lime should result

A Cost-Benefit Assessment of Gasification-Based Biorefining in the Kraft Pulp and Paper Industry

Energy Technology Data Exchange (ETDEWEB)

Eric D. Larson; Stefano Consonni; Ryan E. Katofsky; Kristiina Iisa; W. James Frederick

2007-03-31

Production of liquid fuels and chemicals via gasification of kraft black liquor and woody residues (''biorefining'') has the potential to provide significant economic returns for kraft pulp and paper mills replacing Tomlinson boilers beginning in the 2010-2015 timeframe. Commercialization of gasification technologies is anticipated in this period, and synthesis gas from gasifiers can be converted into liquid fuels using catalytic synthesis technologies that are in most cases already commercially established today in the ''gas-to-liquids'' industry. These conclusions are supported by detailed analysis carried out in a two-year project co-funded by the American Forest and Paper Association and the Biomass Program of the U.S. Department of Energy. This work assessed the energy, environment, and economic costs and benefits of biorefineries at kraft pulp and paper mills in the United States. Seven detailed biorefinery process designs were developed for a reference freesheet pulp/paper mill in the Southeastern U.S., together with the associated mass/energy balances, air emissions estimates, and capital investment requirements. Commercial (''Nth'') plant levels of technology performance and cost were assumed. The biorefineries provide chemical recovery services and co-produce process steam for the mill, some electricity, and one of three liquid fuels: a Fischer-Tropsch synthetic crude oil (which would be refined to vehicle fuels at existing petroleum refineries), dimethyl ether (a diesel engine fuel or LPG substitute), or an ethanol-rich mixed-alcohol product. Compared to installing a new Tomlinson power/recovery system, a biorefinery would require larger capital investment. However, because the biorefinery would have higher energy efficiencies, lower air emissions, and a more diverse product slate (including transportation fuel), the internal rates of return (IRR) on the incremental capital investments would be

Steam slaking of lime - kinetics and technology. New energy effective lime slaking technology in kraft pulping; Aangslaeckning av kalk - kinetik och teknik. Ny energieffektiv teknik foer slaeckning av mesakalk i sulfatmassaindustrin

Energy Technology Data Exchange (ETDEWEB)

Lundqvist, Roland

2008-06-15

Lime stone is widely used in chemical recovery for regeneration of white liquor in kraft pulping. Slaked (hydrated) lime is used to convert (causticize) sodium carbonate into sodium hydroxide, whereby lime mud (calcium carbonate) precipitates from the solution. Lime mud is dried and reburned in a lime kiln, where burned lime (calcium oxide) is formed. The circle is closed when lime is slaked (hydrated) in green liquor in an exotherm reaction. Problems with traditional lime burning and slaking methods are that heat recovery is bad and heat is recovered at low temperatures. With the method described in this report there is potential to increase heat recovery in the causticizing plant, and to recover heat at higher temperatures. The forecasted method means that lime is slaked with water vapour, for example combined with an indirect heated lime mud drier and a lime kiln. This project is a follow-up to pilot tests performed in a specific machine equipment at year 2006. The target group is pulp and paper industry using the kraft process. The owner of this new project is Carnot AB and the project is performed inside the Vaermeforsk Program for Pulp and Paper Industry 2006-2008. Partners and advisers in project group have been KTH Energy Processes, CTH Energy and Environment, LTH Chemical Technology, SMA Mineral AB, and reference group from STORA Enso Skoghall, Sodra Cell, M-Real Husum and SCA Packaging Piteaa. The task in this stage has included market investigations and laboratory tests. Contacts have been made with suppliers, preliminary dimensioning of process equipment and budget offers are received. Economic calculations have been made out of the offers. The laboratory tests are done as an examination paper at KTH Energiprocesser on the reactivity of burned lime from kraft lime kiln when it is slaked with water vapour instead of green liquor. The vapour intended to be used is at atmospheric pressure or even down to 0,2 atm. Complementary addition to these laboratory

Kraft Lignin Depolymerization in an Ionic Liquid without a Catalyst

Directory of Open Access Journals (Sweden)

Amadou Diop

2015-06-01

Full Text Available In this paper, the depolymerization of lignin was successfully achieved by the thermal treatment of kraft lignin in butyl-1,8-diazabicyclo[5.4.0]undec-7-enium chloride ([DBUC4+][Cl-] without a catalyst. The thermal treatment experiments were performed in an oven at 150, 200, and 250 °C for 1 h. The changes in kraft lignin structure over the course of depolymerization were characterized by gel permeation chromatography (GPC, Fourier transform infrared (FTIR spectroscopy, and 1H / 31P NMR analyses. GPC chromatograms indicated that the retention time of the original kraft lignin had shifted toward higher values after the thermal treatment, which indicated lignin depolymerization. The average molecular weight of the lignin obtained after 1 h reaction time decreased by 23, 70, and 58 wt% for the treatment at 150, 200, and 250 °C, respectively. FTIR spectra indicated the cleavage of β-O-4 bonds of kraft lignin. The 1H NMR spectra showed demethylation of all treated kraft lignins. Moreover, the 31P NMR analysis demonstrated that the demethylation phenomenon of the treated kraft lignin contributed to the formation of catechol groups.

78 FR 38877 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-06-28

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 60 [EPA-HQ-OAR-2012-0640] FRL-9829-3 RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... comments on the May 23, 2013, proposed rule titled, ``Kraft Pulp Mills NSPS Review'' is being extended by...

Studies of lignin transformation in polyoxometalate (POM) bleaching of kraft pulp

Science.gov (United States)

Biljana Bujanovic; Richard S. Reiner; Kolby C. Hirth; Sally A. Ralph; Rajai H. Atalla

2005-01-01

In order to elucidate changes occurring in lignin during polyoxometalate delignification of kraft pulp, residual lignins of a series of POM- delignified kraft pulps of decreasing kappa number were isolated and characterized. Oxidative treatment of commercial unbleached kraft pulp was performed using complex POM solutions containing the active [SiVW11O40]anion. For...

HIGHLY ENERGY EFFICIENT D-GLU (DIRECTED-GREEN LIQ-UOR UTILIZATION) PULPING

Energy Technology Data Exchange (ETDEWEB)

Lucia, Lucian A

2013-04-19

Purpose: The purpose of the project was to retrofit the front end (pulp house) of a commercial kraft pulping mill to accommodate a mill green liquor (GL) impregna-tion/soak/exposure and accrue downstream physical and chemical benefits while prin-cipally reducing the energy footprint of the mill. A major player in the mill contrib-uting to excessive energy costs is the lime kiln. The project was intended to offload the energy (oil or natural gas) demands of the kiln by by-passing the causticization/slaking site in the recovery area and directly using green liquor as a pulping medium for wood. Scope: The project was run in two distinct, yet mutually compatible, phases: Phase 1 was the pre-commercial or laboratory phase in which NC State University and the Insti-tute of Paper Science and Technology (at the Georgia Institute of Technology) ran the pulping and associated experiments, while Phase 2 was the mill scale trial. The first tri-al was run at the now defunct Evergreen Pulp Mill in Samoa, CA and lead to a partial retrofit of the mill that was not completed because it went bankrupt and the work was no longer the low-hanging fruit on the tree for the new management. The second trial was run at the MeadWestvaco Pulp Mill in Evedale, TX which for all intents and pur-poses was a success. They were able to fully retrofit the mill, ran the trial, studied the pulp properties, and gave us conclusions.

Engineering Study for a Full Scale Demonstration of Steam Reforming Black Liquor Gasification at Georgia-Pacific's Mill in Big Island, Virginia; FINAL

International Nuclear Information System (INIS)

Robert De Carrera; Mike Ohl

2002-01-01

Georgia-Pacific Corporation performed an engineering study to determine the feasibility of installing a full-scale demonstration project of steam reforming black liquor chemical recovery at Georgia-Pacific's mill in Big Island, Virginia. The technology considered was the Pulse Enhanced Steam Reforming technology that was developed and patented by Manufacturing and Technology Conversion, International (MTCI) and is currently licensed to StoneChem, Inc., for use in North America. Pilot studies of steam reforming have been carried out on a 25-ton per day reformer at Inland Container's Ontario, California mill and on a 50-ton per day unit at Weyerhaeuser's New Bern, North Carolina mill

Extraction of hemicellulose from South African eucalyptus grandis using weak white liquor activation technology and its impact on kraft pulping efficiency

CSIR Research Space (South Africa)

Johakimu, Jonas K

2017-09-01

Full Text Available This work summarises the findings of our research on the activation of woodchips using weak white liquor as an alternative mill self-generated alkaline solvent. The ultimate goal was to gain a better understanding on: the effectiveness of the weak...

System Aspects of Black Liquor Gasification. A review of existing reports

Energy Technology Data Exchange (ETDEWEB)

Berntsson, Thore [Chalmers Univ. of Technology, Goeteborg (Sweden)

2008-12-15

Black liquor gasification (BLG) is one of the high-prioritized RandD areas in Sweden. Research work is going on in the national program BLG-Programme. The main aims with the present study are to: - Identify larger projects dealing with energy oriented system aspects of BLG - Make a synthesis on system aspects results in these projects - Identify need for further work, e.g. as a part of a second period of the BLG Programme. No new work or calculations have been performed, the aim has been only to compile and draw conclusions from existing information. The focus has been on system studies. Most of the research on BLG has been technically, chemically and component oriented. These areas are not included in this report. In Chapter 2 basics for BLG are presented and in Chapter 3 important system aspects of this technology are discussed. Future opportunities for energy savings in mills are crucial for a BLG system, both technically and economically. Therefore present knowledge for such opportunities is presented in Chapter 4. In section 1.4 the report/projects included in this report are introduced and in Chapter 5-13 Summaries, especially on system aspects, of these reports are given. In order to keep the report at a reasonable size only major projects dealing with system aspects during the last 10 year period have been included. In Chapter 14 a synthesis of system aspects dealt with in the different reports is presented and in Chapter 15 suggestions for further work are given. In Chapter 16 references are given and finally in the Attachment a brief overview of different BLG technologies is presented

Caracterização de compostos reduzidos de enxofre gerados na produção de celulose kraft e pré-hidrólise kraft.

Directory of Open Access Journals (Sweden)

Afonso Moraes de Moura

2010-08-01

Full Text Available Um problema ambiental da indústria de celulose kraft é o odor causado pela emissão dos compostos reduzidos de enxofre gerados pela deslignificação de madeiras de um modo em geral. Para monitorar essas emissões, existem equipamentos simples, desenvolvidos para a medição contínua do "total reduced sulphur" (TRS, tal como o analisador coulométrico. Neste trabalho, foram analisados sulfeto de hidrogênio (H2S, metil mercaptana (CH3SH, dimetil sulfeto [(CH32S] e dimetil dissulfeto [(CH32S2], gerados em deslignificações laboratoriais kraft e pré-hidrólise kraft de dois grupos de madeiras de folhosas. Um dos grupos de madeiras continha 25% e o outro 20% de lignina, base peso seco. Foi observado que as madeiras com menores teores de lignina geraram significativamente menores quantidades de compostos reduzidos de enxofre de TRS. Não foram notadas diferenças significativas nas quantidades totais geradas entre os processos de deslignificação estudados. O processo pré-hidrólise kraft foi mais sensível aos teores de lignina da madeira que o processo kraft. Recomenda-se, por isso, trabalhar com madeiras com menores teores de lignina quando do uso do processo pré-hidrólise kraft para produção de celulose. As principais formas geradas de TRS foram dimetil sulfeto e metil mercaptana.

Ole Bjørn Kraft 1893-1980

DEFF Research Database (Denmark)

Skov, Christian Houlberg

2010-01-01

Ole Bjørn Kraft (1893-1980) var en central konservativ politiker i årene før og efter anden verdenskrig. Han markerede sig som udpræget idépolitiker og opnåede ad flere omgange at blive minister.......Ole Bjørn Kraft (1893-1980) var en central konservativ politiker i årene før og efter anden verdenskrig. Han markerede sig som udpræget idépolitiker og opnåede ad flere omgange at blive minister....

Negotiation time table and realization timetable in the grid connection process according to KraftNAV; Verhandlungs- und Realisierungsfahrplan im Netzanschlussverfahren nach der KraftNAV

Energy Technology Data Exchange (ETDEWEB)

Buchmann, Felix [Sozietaet Alber Buchmann Stefan Rechtsanwaelte, Reutlingen (Germany)

2010-04-15

With the ordinance for the regulation of the grid connection from plants of power production (KraftNAV), the conditions of the grid connection were concretized by power station projects with a nominal output of at least 100 MW with an electrical potential of at least 110 kV. Under this aspect, the author of the contribution under consideration reports on the negotiation timetable and realization timetable in the grid connection procedure according to the KraftNAV. The following aspects are treated: Procedure for the grid connection according to KraftNAV in the overview; Promise of the connection and reservation fee; Negotiation timetable; Realization timetable; Requirement timetable; Duties to supply information.

Estudo do liquor de cupuaçu Study of cupuassu liquor

Directory of Open Access Journals (Sweden)

Kelly de Oliveira Cohen

2005-03-01

Full Text Available O cupuaçu (Theobroma grandiflorum Schum, que é um fruto amazônico, vem conquistando a cada ano mais espaço no mercado nacional e internacional com a comercialização de sua polpa. Suas sementes, consideradas como subproduto, vem despertando interesse não só no mundo científico como pelas indústrias. Sabe-se que, a partir das sementes, pode-se obter produtos análogos aos oriundos das sementes de cacau, seguindo as mesmas etapas de processamento. Dentre esses produtos tem-se o liquor de cupuaçu, semelhante ao liquor de cacau que é um dos ingredientes da formulação do chocolate. Este trabalho teve como objetivo o estudo da obtenção e caracterização física, química e físico-química do liquor de cupuaçu. Obteve-se três amostras de liquor de cupuaçu, cada qual partindo de lotes diferentes de fermentação. Foram avaliados a composição centesimal e o comportamento reológico. O liquor de cupuaçu apresentou alto teor de lipídios (63,93 a 66,51% e alto valor calórico (677,35 a 691,17kcal/100g. O teor de proteínas variou de 8,95 a 10,31%. A viscosidade plástica de Casson diminuiu com o aumento de temperatura. A distribuição do tamanho das partículas influenciou nas diferenças de viscosidades entre as amostras, havendo maior redução de viscosidade plástica com o aumento da temperatura nas amostras que apresentaram maior diâmetro de partículas. A gordura de cupuaçu apresentou comportamento newtoniano à 40ºC.Cupuassu (Theobroma grandiflorum Schum is an amazon fruit, that each year is conquering more space in national and international market with the commercialization of its pulp. Its seeds, considered as subproducts, are arousing interest not only in the scientific world but also in the industry. It's known that from those seeds, it can be obtained analogous products as those cocoa seeds, following the same stages of processing. Among those products there is the cupuassu liquor, similar to cocoa liquor that is one

Structural elucidation and antioxidant activity of lignin isolated from rice straw and alkali‑oxygen black liquor.

Science.gov (United States)

Jiang, Bo; Zhang, Yu; Gu, Lihui; Wu, Wenjuan; Zhao, Huifang; Jin, Yongcan

2018-05-17

Alkali‑oxygen cooking of lignocellulose offers lignin many structural properties and bioactivities for biorefinery. In this work, milled wood lignin (MWL) and alkali‑oxygen lignin (AOL) were isolated from rice straw and alkali‑oxygen black liquor, respectively. The lignin structure was characterized by spectroscopy and wet chemistry. Antioxidant activity of lignins was assessed by DPPH·and ABTS scavenging ability assay. Results showed the oxidization and condensation of lignin occurred during alkali‑oxygen cooking. The p-hydroxyphenyl was more easily removed from rice straw than guaiacyl and syringyl units. The ester or ether linkages derived from hydroxycynnamic acids, and the main interunit linkages, i.e. β-O-4' bonds, were mostly cleaved. Lignin-xylan complex had high reactivity under alkali‑oxygen condition. Tricin, incorporated into lignin, was detected in MWL but was absent in AOL. Nitrobenzene oxidation showed MWL can well represent the protolignin of rice straw, and the products yield decreased dramatically after alkali‑oxygen cooking. AOL had higher radical scavenging ability than MWL indicating alkali‑oxygen cooking was an effective pathway for the enhancement of antioxidant activity of lignin. Copyright © 2018 Elsevier B.V. All rights reserved.

40 CFR 98.270 - Definition of source category.

Science.gov (United States)

2010-07-01

... this section: (1) Chemical recovery furnaces at kraft and soda mills (including recovery furnaces that burn spent pulping liquor produced by both the kraft and semichemical process). (2) Chemical recovery... into paperboard products (e.g., containers), or operate coating and laminating processes. (b) The...

Fractionation and characterization of saccharides and lignin components in wood prehydrolysis liquor from dissolving pulp production.

Science.gov (United States)

Wang, Zhaojiang; Wang, Xiaojun; Jiang, Jungang; Fu, Yingjuan; Qin, Menghua

2015-08-01

Saccharides and lignin components in prehydrolysis liquor (PHL) from kraft-based dissolving pulp production was characterized after being fractionated using membrane filtration. The results showed that the membrane filtration provided a method for organics fractionation with considerable recovery rate, but exhibited some disadvantages. Besides the limited ability in purifying oligosaccharides (OS) due to the overlaps of molecular weight distribution with lignin components, the membrane filtration could not improve the homogeneity of OS as indicated by the analysis of chemical compositions and the degree of polymerization (DP), which may be ascribed to the linear conformation of OS. The characterization of lignin components indicated a great potential for polymer industry because of the remarkable content of phenolic hydroxyl groups (PhOH), especially for low molecular weight (LMW) fraction. It was concluded the organics in PHL provided streams of value-added chemicals. However, the practical significance thereof can be realized and maximized only when they are successfully and completely fractionated. Copyright © 2015 Elsevier Ltd. All rights reserved.

Multivariate Analysis of Hemicelluloses in Bleached Kraft Pulp Using Infrared Spectroscopy.

Science.gov (United States)

Chen, Zhiwen; Hu, Thomas Q; Jang, Ho Fan; Grant, Edward

2016-12-01

The hemicellulose composition of a pulp significantly affects its chemical and physical properties and thus represents an important process control variable. However, complicated steps of sample preparation make standard methods for the carbohydrate analysis of pulp samples, such as high performance liquid chromatography (HPLC), expensive and time-consuming. In contrast, pulp analysis by attenuated total internal reflection Fourier transform infrared spectroscopy (ATR FT-IR) requires little sample preparation. Here we show that ATR FT-IR with discrete wavelet transform (DWT) and standard normal variate (SNV) spectral preprocessing offers a convenient means for the qualitative and quantitative analysis of hemicelluloses in bleached kraft pulp and alkaline treated kraft pulp. The pulp samples investigated include bleached softwood kraft pulps, bleached hardwood kraft pulps, and their mixtures, as obtained from Canadian industry mills or blended in a lab, and bleached kraft pulp samples treated with 0-6% NaOH solutions. In the principal component analysis (PCA) of these spectra, we find the potential both to differentiate all pulps on the basis of hemicellulose compositions and to distinguish bleached hardwood pulps by species. Partial least squares (PLS) multivariate analysis gives a 0.442 wt% root mean square errors of prediction (RMSEP) for the prediction of xylan content and 0.233 wt% RMSEP for the prediction of mannan content. These data all support the idea that ATR FT-IR has a great potential to rapidly and accurately predict the content of xylan and mannan for bleached kraft pulps (softwood, hardwood, and their mixtures) in industry. However, the prediction of xylan and mannan concentrations presented a difficulty for pulp samples with modified cellulose crystalline structure. © The Author(s) 2016.

Heat transfer for falling film evaporation of industrially relevant fluids up to very high Prandtl numbers

Science.gov (United States)

Gourdon, Mathias; Karlsson, Erik; Innings, Fredrik; Jongsma, Alfred; Vamling, Lennart

2016-02-01

In many industrial applications, falling film evaporation is an attractive technique for solvent removal due to high heat transfer and low residence times. Examples are the powder production in the dairy industry and in kraft pulp production process to remove water from so called black liquor. Common for both applications is that the fluids exhibit high viscosities in industrial practice. In this paper, results from experimental studies on both black liquor and a dairy product are reported for Prandtl numbers up to 800. The results are compared with several existing correlation in literature, and the need for a modified correlation is recognized especially to cover higher Prandtl-numbers. The following correlation for the turbulent flow region with 3 < Pr < 800 was derived from the data: {Nu}t = 0.0085 \\cdot Re^{0.2} \\cdot {Pr^{0.65}} The correlation has been compared to literature data from one additional study on two other fluids (propylene glycol and cyclohexanol) with fairly high Prandtl-numbers, from 40 to 58 and from 45 to 155 respectively and the agreement was within ±40 %.

Bacterial decolorization and detoxification of black liquor from rayon grade pulp manufacturing paper industry and detection of their metabolic products.

Science.gov (United States)

Chandra, Ram; Abhishek, Amar; Sankhwar, Monica

2011-06-01

This study deals with the decolorization of black liquor (BL) by isolated potential bacterial consortium comprising Serratia marcescens (GU193982), Citrobacter sp. (HQ873619) and Klebsiella pneumoniae (GU193983). The decolorization of BL was studied by using the different nutritional as well as environmental parameters. In this study, result revealed that the ligninolytic activities were found to be growth associated and the developed bacterial consortium was efficient for the reduction of COD, BOD and color up to 83%, 74% and 85%, respectively. The HPLC analysis of degraded samples of BL has shown the reduction in peak area compared to control. Further, the GC-MS analysis showed that, most of the compounds detected in control were diminished after bacterial treatment while, formic acid hydrazide, 4-cyclohexane-1,2-dicarboxylic acid, carbamic acid, 1,2-benzenedicarboxylic acid and erythropentanoic acid were found as new metabolites. Further, the seed germination test using Phaseolus aureus has supported the detoxification of bacterial decolorized BL. Copyright © 2011 Elsevier Ltd. All rights reserved.

Precipitation and valorisation of lignin obtained from South African Kraft mill black liquor

CSIR Research Space (South Africa)

Namane, Mpho

2016-04-01

Full Text Available (NMR), size exclusion chromatography (SEC), and pyrolysis-gas chromatography/mass spectrometry (Py-GC/MS). SEC data revealed a narrow molecular weight distribution with a small polydispersity index in the lignin sample – all desirable features...

Conversion of tall oil soap and lignin into liquid fuels II; Suovan ja ligniinin jalostaminen polttonesteiksi II

Energy Technology Data Exchange (ETDEWEB)

Oasmaa, A.; McKeough, P. [VTT Energy, Espoo (Finland)

1995-11-01

The objective of the project was to evaluate the following upgrading processes for producing bio-oils for energy production: catalytic upgrading of kraft black liquor, thermal treatment of tall oil soap, and catalytic hydrotreatment of Milox-lignin. The best-quality product from black liquor was obtained by treating black liquor (20 % moisture) at 420 deg C with an ammoniumheptamolybdate (AHM) catalyst under hydrogen for 60 minutes.The product was washed with water (product:water = 1:2) in order to remove the inorganics. The oil product contained 74 % of the energy content of the black liquor organics. Regeneration of the AHM catalyst appears technically feasible. Raw tall oil soap cracks at 450 degr. C under nitrogen into straight-chain hydrocarbons and naphthalene and phenanthrene derivatives. The best-quality oil product was obtained at a residence time of 60 - 120 minutes. This product contained no fatty acids as impurities. The process concept consists of two steps: heat treatment at 450 degr. C and product separation. The energy yield of the hydrocarbon oil product is about 50 %. The residue slurry (estimated energy content 20 %) and gases (energy content 25 %) are led to the recovery boiler. Milox lignin can be hydrotreated at 420 deg C (60 minutes) with a mixture (1:1) of sulphided NiMo- and Cr{sub 2}O{sub 3}-catalysts to a high-quality oil product (42 wt% yield of hexane solubles). The activity of catalysts decreased in order: sulphided NiMo/Al{sub 2}O{sub 3}:Cr{sub 2}O{sub 3} (1:1), sulphided NiMo/zeolite, NiMo/Al{sub 2}O{sub 3}, ATTM (no activity). A decrease in hydrogen partial pressure yielded a lower quality product. (author)

Conversion of tall oil soap and lignin into liquid fuels; Suovan ja ligniinin jalostaminen polttonesteiksi

Energy Technology Data Exchange (ETDEWEB)

Oasmaa, A.; McKeough, P. [VTT Energy, Espoo (Finland)

1998-12-31

The objective of the project was to evaluate the following upgrading processes for producing bio-oils for energy production: catalytic upgrading of kraft black liquor, thermal treatment of tall oil soap, and catalytic hydrotreatment of Milox-lignin. The best-quality product from black liquor was obtained by treating black liquor (20% moisture) at 420 deg C with an ammoniumheptamolybdate (AHM) catalyst under hydrogen for 60 minutes. The product was washed with water (product:water = 1:2) in order to remove the inorganics. The oil product contained 74% of the energy content of the black liquor organics. Regeneration of the AHM catalyst appears technically feasible. Raw tall oil soap cracks at 450 deg C under nitrogen into straight-chain hydrocarbons and naphthalene and phenanthrene derivatives. The best-quality oil product was obtained at a residence time of 60 - 120 minutes. This product contained no fatty acids as impurities. The process concept consists of two steps: heat treatment at 450 deg C and product separation. The energy yield of the hydrocarbon oil product is about 50%. The residue slurry (estimated energy content 20%) and gases (energy content 25%) are led to the recovery boiler. Milox lignin can be hydrotreated at 420 deg C (60 minutes) with a mixture (1:1) of sulphided NiMo- and Cr{sub 2}O{sub 3}-catalysts to a high-quality oil product (42 wt% yield of hexane solubles). The activity of catalysts decreased in order: sulphided NiMo/Al{sub 2}O{sub 3}:Cr{sub 2}O{sub 3} (1:1), sulphided NiMo/zeolite, NiMo/Al{sub 2}O{sub 3}, ATTM (no activity). A decrease in hydrogen partial pressure yielded a lower quality product. (orig.)

Investigation of freeze concentration as a process for industrial energy conservation in black liquor, acetic acid, and citrus juice applications. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1979-07-01

One of the largest consumers of energy in industrial processing is the equipment that concentrates weak aqueous solutions to stronger more sellable or reusable concentrations. The technical and economic feasibility of applying freeze concentration (that is, crystallization and removal from solution of pure solvent - water) as an alternative to heat evaporation (or distillation) to three industrial applications is established. For each of the applications - pulp mill black liquor concentration, acetic acid recovery and orange juice concentration - the economic analyses indicate that the energy savings achievable by freezing justify the respective capital investments with pay out periods of generally one to three years. Past freeze concentration operations have been in the 10,000 to 100,000 gallons per day range for sea water desalination. Research and development work will be required to adapt this work to the three industrial applications.

ON THE RECOVERY OF HEMICELLULOSE BEFORE KRAFT PULPING

Directory of Open Access Journals (Sweden)

Carlos Vila,

2012-07-01

Full Text Available To assess the feasibility of implementing hemicellulose recovery stages in kraft mills, Eucalyptus globulus wood samples were subjected to aqueous treatments with hot, compressed water (autohydrolysis processing to achieve partial dissolution of xylan. Autohydrolyzed solids were subjected to kraft pulping under selected conditions to yield a pulp of low kappa number, and to an optimized TCF bleaching sequence made up of three stages (alkaline oxygen delignification, chelating, and pressurized hydrogen peroxide, with minimized additions of pulping and bleaching chemicals. The final product had a relatively low kappa number (1.4, 641 mL/g ISO intrinsic viscosity, and 86.4% brightness.

Kraft cooking of gamma irradiated wood, (2)

International Nuclear Information System (INIS)

Inaba, Masamitsu; Meshitsuka, Gyosuke; Ishizu, Atsushi; Nakano, Junzo

1981-01-01

Pre-irradiation of wood in alkaline aqueous ethanol increases kraft pulp yield by up to 1.2%, as already reported. In order to clarify the mechanism of the pulp yield gain, the behaviors of lignin and carbohydrates during pre-irradiation and cooking were investigated. The results are summarized as follows: 1) γ-Irradiation of guaiacylethane in alkaline aqueous ethanol produced 5-(1-hydroxyethyl)-guaicylethane, which is formed by radical coupling between α-hydroxyethyl radical from ethanol and guaiacylethane radical having an unpaired electron at C-5. 5,5'-Dehydrodiguaiacylethane, which may be a predominant product produced by γ-irradiation in the absence of ethanol, was also detected. 2) The yield of vanillin obtained by nitrobenzene oxidation of MWL decreased with an increase of γ-ray dosage. The presence of ethanol during γ-irradiation lessened the extent of this decrease and also the degradation of cellobiose. 3) Gel filtration of the products obtained by γ-irradiation of MWL and cellobiose in the presence of 14 C-ethanol showed the possible combination between ethanol and MWL or cellobiose. 4) Molecular weight distributions of kraft lignin obtained from pre-irradiated beech chips were compared with those obtained from unirradiated chips. This result shows that γ-irradiation in the presence of ethanol decreases the ability of lignin to condense during kraft cooking. (author)

Yield Improvement and Energy Savings Uing Phosphonates as Additives in Kraft pulping

Energy Technology Data Exchange (ETDEWEB)

Ulrike W. Tschirner; Timothy Smith

2007-03-31

Project Objective: Develop a commercially viable modification to the Kraft process resulting in energy savings, increased yield and improved bleachability. Evaluate the feasibility of this technology across a spectrum of wood species used in North America. Develop detailed fundamental understanding of the mechanism by which phosphonates improve KAPPA number and yield. Evaluate the North American market potential for the use of phosphonates in the Kraft pulping process. Examine determinants of customer perceived value and explore organizational and operational factors influencing attitudes and behaviors. Provide an economic feasibility assessment for the supply chain, both suppliers (chemical supply companies) and buyers (Kraft mills). Provide background to most effectively transfer this new technology to commercial mills.

Producing a True Lignin Depolymerase for Biobleaching Softwood Kraft Pulp

Energy Technology Data Exchange (ETDEWEB)

Simo Sarkanen

2002-02-04

This project constituted an intensive effort devoted to producing, from the white-rot fungus Tramets Cingulata, a lignin degrading enzyme (lignin depolymerase) that is directly able to biobleach or delignify softwood kraft pulp brownstock. To this end, the solutions in which T. cingulata was grown contained dissolved kraft lignin which fulfilled two functions; it behaved as a lignin deploymerase substrate and it also appeared to act as an inducer of enzyme expression. However, the lignin depolymerase isoenzymes (and other extracellular T. cingulata enzymes) interacted very strongly with both the kraft lignin components and the fungal hypae, so the isolating these proteins from the culture solutions proved to be unexpectedly difficult. Even after extensive experimentation with a variety of protein purification techniques, only one approach appeared to be capable of purifying lignin depolymerases to homogeneity. Unfortunately the procedure was extremely laborious; it involved the iso electric focusing of concentrated buffer-exchanged culture solutions followed by electro-elution of the desired protein bands from the appropriate polyacrylamide gel segments

Soda-anthraquinone, kraft and organosolv pulping of holm oak trimmings.

Science.gov (United States)

Alaejos, J; López, F; Eugenio, M E; Tapias, R

2006-11-01

The operating conditions for an organosolv (ethyleneglycol) and two alkaline (soda-anthraquinone and kraft) processes for obtaining cellulose pulp and paper from holm oak (Quercus ilex) wood trimmings were optimized. A range of variation for each process variable (viz. temperature, cooking time and soda or ethyleneglycol concentration) was established and a central composite experimental design involving three independent variables at three different variation levels was applied. The results obtained with the three cooking processes used were compared and those provided by the kraft process were found to be the best. Thus, the tensile index values it provided (5.9-16.3 N m/g) were 23.7% and 41.5% better than those obtained with the soda-AQ and ethyleneglycol processes, respectively. Also, the kraft process provided the best burst index, brightness and kappa number values. Based on the optimum working ranges, the temperature and cooking time were the variables resulting in the most and least marked changes, respectively, in pulp properties.

Authentication of Chinese vintage liquors using bomb-pulse 14C

Science.gov (United States)

Cheng, Peng; Zhou, Weijian; Burr, G. S.; Fu, Yunchong; Fan, Yukun; Wu, Shugang

2016-12-01

The older a bottle of Chinese vintage liquor is, the higher the price it commands. Driven by the potential for higher profits, some newly-founded distilleries openly sell liquor whose storage ages are exaggerated. In China, the market for vintage liquor has become fraught with uncertainty and a pressing need has arisen to establish an effective method to authenticate the age of vintage liquors. A radiocarbon (14C) dating method is described here that can verify cellar-stored years of Chinese liquors distilled within the last fifty years. Two different flavored Chinese liquors produced in “the golden triangular region” in the Upper Yangtze River region in southwest China, with known cellar-stored years, were analyzed to benchmark the technique. Strong flavored liquors are found to be consistent with local atmospheric Δ14C values. A small offset of 2-3 years between predicted vintage years of soy-sauce flavored liquors and strong flavored liquors is found to be associated with the fermentation cycle of certain varieties. The technique can measure cellar-stored years of a wide range of liquors including those with fundamentally different aromas. This demonstrates the strength of our method in identifying suspect Chinese vintage liquors.

The Kraft Pulp And Paper Properties of Sweet Sorghum Bagasse (Sorghum bicolor L Moench

Directory of Open Access Journals (Sweden)

Widya Fatriasari

2015-05-01

Full Text Available This study investigated the potency of sweet sorghum (Sorghum bicolor bagasse as raw material for pulp and paper using kraft pulping. The effects of alkali and sulfidity loading on kraft pulp and paper properties were also investigated. The pulping condition of the kraft pulp consisted of three levels of alkali loading (17, 19 and 22% and sulfidity loading (20, 22 and 24%. The maximum cooking temperature was 170°C for 4 h with a liquid to wood ratio of 10:1. Kraft pulping of this Numbu bagasse produced good pulp indicated by high screen yield and delignification selectivity with a low Kappa number (< 10. The unbleached pulp sheet produced a superior brightness level and a high burst index. The increase of active alkali loading tended to produce a negative effect on the pulp yield, Kappa number and paper sheet properties. Therefore, it is suggested to use a lower active alkaline concentration.

Study on the Modification of Bleached Eucalyptus Kraft Pulp Using Birch Xylan

Science.gov (United States)

Wenjia Han; Chuanshan Zhao; Thomas Elder; Rendang Yang; Dongho Kim; Yunqiao Pu; Jeffery Hsieh; Arthur J. Ragauskas

2012-01-01

In this study, birch xylan was deposited onto elementally chlorine free (ECF) bleached eucalyptus kraft pulp, and the corresponding changes in physical properties were determined. An aqueous 5% birch xylan solution at pH 9 was added to 5 wt% slurry of bleached kraft eucalyptus fibers, with stirring at 70 C for 15 min after which the pH was adjusted to 5–6. The xylan...

Papermaking Properties of Carpinus betulus with kraft, Soda and Soda-Urea Pulping Processes

Directory of Open Access Journals (Sweden)

Rasoul Darstan

2013-06-01

Full Text Available This research was carried out in order to comparatively investigate the hornbeam kraft, soda and soda-urea papermaking properties. The selected treatment in kraft process had an average yield of 44.43% and kappa number of 23.75. In soda process the selected treatment had an average yield of 38.75% and kappa number of 19.28. In soda-urea process, the selected treatments had an average yield of 39.85, 40.1, 40.5, 39.8 and 40.61 and kappa number of 21.21, 22.33, 22.66, 25.28 and 26.85. After refining the selected pulp to reach the freeness of 400±25 ml CSF, 60 g/m2 handsheets were made and physical, mechanical and optical properties were measured. Results showed that kraft pulps had higher yield and better refinability than soda and soda-urea pulps. Papers made from kraft process had higher strength properties than those made of soda and soda-urea process. With addition of urea, yield and kappa number of pulps increased. The highest improvement in tensile index, breaking length and tear index was achieved with addition of 3% urea and the highest improvement in burst index was achieved with adding 4% urea. Results of brightness measurements showed that papers from kraft and soda processes had the lowest and highest brightness degree respectively. With the addition of urea, brightness of papers decreased.

Visual Spatial Disorientation: Re-Visiting the Black Hole Illusion

Science.gov (United States)

2007-01-24

National Transportation Safety Board. Controlled Flight into Terrain, Korean Air Flight 801 , Nimitz Hill, Guam; 1997. 50. National Transportation Safety...According to a Boeing study of worldwide commercial airline accidents, the approach and landing phase of flying, although only accounting for 4% of the...VISUAL SPATIAL DISORIENTATION Kraft (31) described four night visual, landing airline accidents. Black Hole Illusion 5 1. In 1965, a United Airlines

Kraft pulping of industrial wood waste

Science.gov (United States)

Aziz. Ahmed; Masood. Akhtar; Gary C. Myers; Gary M. Scott

1998-01-01

Most of the approximately 25 to 30 million tons of industrial wood waste generated in the United States per year is burned for energy and/or landfilled. In this study, kraft pulp from industrial wood waste was evaluated and compared with softwood (loblolly pine, Douglas-fir) and hardwood (aspen) pulp. Pulp bleachability was also evaluated. Compared to loblolly pine...

Uranium complex recycling method of purifying uranium liquors

International Nuclear Information System (INIS)

Elikan, L.; Lyon, W.L.; Sundar, P.S.

1976-01-01

Uranium is separated from contaminating cations in an aqueous liquor containing uranyl ions. The liquor is mixed with sufficient recycled uranium complex to raise the weight ratio of uranium to said cations preferably to at least about three. The liquor is then extracted with at least enough non-interfering, water-immiscible, organic solvent to theoretically extract about all of the uranium in the liquor. The organic solvent contains a reagent which reacts with the uranyl ions to form a complex soluble in the solvent. If the aqueous liquor is acidic, the organic solvent is then scrubbed with water. The organic solvent is stripped with a solution containing at least enough ammonium carbonate to precipitate the uranium complex. A portion of the uranium complex is recycled and the remainder can be collected and calcined to produce U 3 O 8 or UO 2

Factors controlling alkalisalt deposition in recovery boiler- release mechanisms

Energy Technology Data Exchange (ETDEWEB)

McKeough, P.; Kylloenen, H.; Kurkela, M. [VTT Energy, Espoo (Finland). Process Technology Group

1996-12-01

As part of a cooperative effort to develop a model to describe the behaviour of inorganic compounds in kraft recovery boilers, an experimental investigation of the release of sulphur during black liquor pyrolysis has been undertaken. Previous to these studies, the mechanisms of sulphur release and the reasons for the observed effects of process conditions on sulphur release were very poorly understood. On the basis of the experimental results, the main reactions leading to sulphur release have been elucidated with a fair degree of certainty. Logical explanations for the variations of sulphur release with temperature and with liquor solids content have been proposed. The influence of pressure has been investigated in order to gain insights into the effects of mass transfer on the sulphur-release rate. In the near future, the research will be aimed at generating the kinetic data necessary for modelling the release of sulphur in the recovery furnace. (author)

Mystery behind Chinese liquor fermentation

OpenAIRE

Jin, Guangyuan; Zhu, Yang; Xu, Yan

2017-01-01

Background Chinese liquor, a very popular fermented alcoholic beverage with thousands of years’ history in China, though its flavour formation and microbial process have only been partly explored, is facing the industrial challenge of modernisation and standardisation for food quality and safety as well as sustainability. Meanwhile, the hidden knowledge behind the complicated and somehow empirical solid-state fermentation process of Chinese liquor can enrich the food sector to improve our qua...

EFFECT OF LIGNIN CONTENT OF Eucalyptus globulus WOOD IN KRAFT PULPING PERFORMANCE

Directory of Open Access Journals (Sweden)

Gabriel Valim Cardoso

2011-03-01

Full Text Available In this research, it was analyzed the lignin content effect of Eucalyptus globulus wood in kraft pulping optimization. Seventy-two laboratory cooking were made with wood chips obtained from six Eucalyptus globulus trees selected from a group of 50 trees. The wood chips from three trees with the lowest lignin content, with average 20,53%, were mixed proportionally based on the tree weights, obtaining the sample of low lignin content wood. The same was made to obtain the sample for wood chips with the highest lignin content, with average 23,02%. The two lignin levels were statistically different. The two wood samples had basic densities statistically not different. Using three maximum temperatures levels (160, 165 and 170ºC, and three active alkali charged (17, 18,5 and 20%, the wood chips were converted to kraft pulps. The pulps were then characterized to analyze the influence of the distinct treatments employed in the cooking on their properties. The effect of the cooking conditions was expressed by mathematical models in order to determine the optimum points for each of the evaluated properties. The optimization process indicated maximum temperature of 168ºC, and active alkali of 19%, for maximum kraft pulping yield to achieve kappa number 18; this result was for woods with low lignin content. For woods containing the high lignin content, the optimization showed maximum cooking temperature of 169ºC and active alkali of 19% for kappa number of 18. The average reduction of 2,49% in wood lignin content resulted a correspondent gain of 2,2% in the kraft yield (o.d. basis and a reduction on the active alkali charge of 1,2% (o.d. basis to achieve kappa numbers from 16 to 19, preserving pulp properties. If the option is to work with kappa number 19 instead of 16, the gain in kraft yield is approximately 2%. Therefore, when working with low lignin content wood and kappa number 19 instead of 16, a substantial gain of approximately 4,2% is obtained

Kraft cooking of gamma irradiated wood, (1). Effect of alcohol additives on pre-irradiation

Energy Technology Data Exchange (ETDEWEB)

Inaba, M; Meshitsuka, G; Nakano, J [Tokyo Univ. (Japan). Faculty of Agriculture

1979-12-01

Studies have been made of kraft cooking of gamma irradiated wood. Beech (Fagus crenata Blume) wood meal suspended in aqueous alkaline alcohol was irradiated up to 1.5 KGy (0.15 Mrad) with gamma rays from a Co-60 source in the presence or absence of oxygen. The irradiated wood meals were washed thoroughly with fresh water, air dried and cooked under the ordinary cooking conditions. The results are summarized as follows: (1) Pre-irradiation in aqueous alkali have negligible effect on kraft cooking. (2) In the case of ethanol addition (50 g/l), pre-irradiation in vacuo shows acceleration of delignification and stabilization of carbohydrates during kraft cooking. Cooked yield gain by pre-irradiation was about 1.2 in all, over the range of delignification from 80 to 90%. Aqueous ethanol without alkali also shows positive but smaller effect than that with alkali. (3) Propanol, iso-propanol and butanol show positive but smaller effects than ethanol. However, methanol does not show any positive effect. (4) Irradiation in the presence of oxygen does not show any attractive effect on kraft cooking.

Potentialities of spinal liquor scanography

International Nuclear Information System (INIS)

Vlakhov, N.; Vylkanov, P.

1986-01-01

It is shown that spinal liquor scanography is a harmless and informative method for the examination of patients, permitting to detect injury foci for spinal cord tumours in 90% cases, for acute injuries of the vertebral column and spinal cord in 89.5% cases, for herniation of nucleus pulposus in 81% cases. The method of spinal liquor scanography can be used in neurology and neurosurgery to select the method of treatment and to evaluate its efficiency

Removal of COD and color loads in bleached kraft pulp effluents by bottom ashes from boilers.

Science.gov (United States)

Van Tran, A

2008-07-01

The effectiveness of the bottom ashes from biomass and coal-fired boilers in removing chemical oxygen demand (COD) and colorloads in effluents of a kraft pulp bleachery plant is investigated. The effluents tested are those of the sulfuric acid treatment (A stage) of a hardwood kraft pulp, and of the first acidic (chlorine or chlorine dioxide) and second alkaline (extraction) stages in the chlorine and elemental chlorine-free (ECF) bleaching lines of hardwood and softwood kraft pulps. The coal-fired boiler's bottom ashes are unable to remove either COD or color load in the bleached kraft pulp effluents. However, the bottom ashes of the biomass boiler are effective in removing COD and color loads of the acidic and alkaline effluents irrespective of the bleaching process or wood species. In particular, these ashes increase the pH of all the effluents examined.

The energy efficiency partnership - Kraft General Foods and Boston Edison Company

International Nuclear Information System (INIS)

Crowley, J.C.; Donoghue, J.P.

1993-01-01

During the past twenty years, inordinate shifts in the supply and demand of energy have forced both electric utility companies and their customers to investigate new and innovative ways to satisfy the ever increasing demand for electricity. The Energy Efficiency Partnership, developed between Kraft General Foods and Boston Edison Company, presents an exemplary study of how two corporate giants creatively solved the problem of uncontrolled energy costs and its positive effect on the overall operations of Kraft General Foods, Framingham. But the Energy Efficiency Partnership did more than reduce energy costs, it provided benefits to all parties on the playing field. To understand its significance, a review of the partnership's history is paramount. The first official announcement of the Energy Efficiency Partnership was made on April 9, 1990. Framingham, MA, The Commonwealth of Massachusetts Kraft General Foods Framingham, and Boston Edison Company have joined forces in a $3.6 million dollar energy partnership that will help keep 250 industrial jobs in Massachusetts and could lead to the future expansion of the international food company's Framingham facility

Difference of microbial community stressed in artificial pit muds for Luzhou-flavour liquor brewing revealed by multiphase culture-independent technology.

Science.gov (United States)

Zhang, L; Zhou, R; Niu, M; Zheng, J; Wu, C

2015-11-01

Artificial pit muds (APMs) is produced by peats, aged pit muds, yellow and black clays etc. and is one of essential factors for Luzhou-flavour liquor production. The microbial community of APMs significantly influence the quality of Luzhou-flavour liquor. The aim of this study was to investigate the differences in bacterial, archaeal and fungal community of APMs, starters and materials. Multiphase culture-independent technology were employed in this study, including nested PCR-denaturing gradient gel electrophoresis (nested PCR-DGGE), phospholipid fatty acid (PLFA), phospholipid ether lipids (PLEL) and fluorescence in situ hybridization (FISH) analysis. Results suggested that the microbial diversity significantly changed under environmental stress and different culture patterns during APMs cultivation. The dominant bacteria in APMs mainly fell into Clostridiales, Lactobacillales, Bacteroidales and Rhizobiales, Archaea affiliated with Methanomicrobiales and Methanosarcinales, and fungi belonged to Saccharomycetales and Eurotiales. Furthermore, the microbial community structures of APMs cultured by ground pile pattern were more similar with that of aged pit muds, meanwhile, the relative bands intensities of microbes, which are the main contributors for liquor brewing, increased with the culture times. Not only the niche selection and biogeochemical properties of APMs, but also the mutual collaboration and constraint between different microbes may result in enriching different liquor-brewing microbes into APMs. APM cultivation technology was necessary to promote enriching functional liquor-brewing microbes into APMs. These results may facilitate understanding the microbial succession during APMs manufacture. © 2015 The Society for Applied Microbiology.

Recyclable zein-coated kraft paper and linerboard

Science.gov (United States)

Nicholas Parris; Marguerite Sykes; Leland C. Dickey; Jack L. Wiles; Thomas J. Urbanik; Peter H. Cooke

2002-01-01

Recyclability of kraft paper and linerboard coated with commercial zein and paraffin wax or a zein-lipid mixture was evaluated using conventional recycling processes. Zein, an alcohol-soluble protein from corn, exhibits both grease and water vapor barrier properties. Strength properties, grease resistance, and water vapor barrier proper-ties were measured on handsheets...

Composite tube cracking in kraft recovery boilers: A state-of-the-art review

Energy Technology Data Exchange (ETDEWEB)

Singbeil, D.L.; Prescott, R. [Pulp and Paper Research Inst. of Canada, Vancouver, British Columbia (Canada); Keiser, J.R.; Swindeman, R.W. [Oak Ridge National Lab., TN (United States)

1997-07-01

Beginning in the mid-1960s, increasing energy costs in Finland and Sweden made energy recovery more critical to the cost-effective operation of a kraft pulp mill. Boiler designers responded to this need by raising the steam operating pressure, but almost immediately the wall tubes in these new boilers began to corrode rapidly. Test panels installed in the walls of the most severely corroding boiler identified austenitic stainless steel as sufficiently resistant to the new corrosive conditions, and discussions with Sandvik AB, a Swedish tube manufacturer, led to the suggestion that coextruded tubes be used for water wall service in kraft recovery boilers. Replacement of carbon steel by coextruded tubes has solved most of the corrosion problems experienced by carbon steel wall tubes, however, these tubes have not been problem-free. Beginning in early 1995, a multidisciplinary research program funded by the US Department of Energy was established to investigate the cause of cracking in coextruded tubes and to develop improved materials for use in water walls and floors of kraft recovery boilers. One portion of that program, a state-of-the-art review of public- and private-domain documents related to coextruded tube cracking in kraft recovery boilers is reported here. Sources of information that were consulted for this review include the following: tube manufacturers, boiler manufacturers, public-domain literature, companies operating kraft recovery boilers, consultants and failure analysis laboratories, and failure analyses conducted specifically for this project. Much of the information contained in this report involves cracking problems experienced in recovery boiler floors and those aspects of spout and air-port-opening cracking not readily attributable to thermal fatigue. 61 refs.

A multi-criteria decision analysis of management alternatives for anaerobically digested kraft pulp mill sludge.

Directory of Open Access Journals (Sweden)

Martijn Eikelboom

Full Text Available The Multi-Criteria Decision Analysis (MCDA procedure was used to compare waste management options for kraft pulp mill sludge following its anaerobic digestion. Anaerobic digestion of sludge is advantageous because it produces biogas that may be used to generate electricity, heat and biofuels. However, adequate management of the digested sludge is essential. Landfill disposal is a non-sustainable waste management alternative. Kraft pulp mill digested sludge applied to land may pose risks to the environment and public health if the sludge has not been properly treated. This study is aimed to compare several recycling alternatives for anaerobically digested sludge from kraft pulp mills: land application, landfill disposal, composting, incineration, pyrolysis/gasification, and biofuel production by algae. The MCDA procedure considered nine criteria into three domains to compare digested sludge recycling alternatives in a kraft pulp mill: environmental (CO2 emission, exposure to pathogens, risk of pollution, material and energy recovery, economic (overall costs, value of products and technical (maintenance and operation, feasibility of implementation. The most suitable management options for digested sludge from kraft pulp mills were found to be composting and incineration (when the latter was coupled with recycling ash to the cement industry. Landfill disposal was the worst option, presenting low performance in feasibility of implementation, risk of pollution, material and energy recovery.

A multi-criteria decision analysis of management alternatives for anaerobically digested kraft pulp mill sludge

Science.gov (United States)

Eikelboom, Martijn; Lopes, Alice do Carmo Precci; Silva, Claudio Mudadu; Rodrigues, Fábio de Ávila; Zanuncio, José Cola

2018-01-01

The Multi-Criteria Decision Analysis (MCDA) procedure was used to compare waste management options for kraft pulp mill sludge following its anaerobic digestion. Anaerobic digestion of sludge is advantageous because it produces biogas that may be used to generate electricity, heat and biofuels. However, adequate management of the digested sludge is essential. Landfill disposal is a non-sustainable waste management alternative. Kraft pulp mill digested sludge applied to land may pose risks to the environment and public health if the sludge has not been properly treated. This study is aimed to compare several recycling alternatives for anaerobically digested sludge from kraft pulp mills: land application, landfill disposal, composting, incineration, pyrolysis/gasification, and biofuel production by algae. The MCDA procedure considered nine criteria into three domains to compare digested sludge recycling alternatives in a kraft pulp mill: environmental (CO2 emission, exposure to pathogens, risk of pollution, material and energy recovery), economic (overall costs, value of products) and technical (maintenance and operation, feasibility of implementation). The most suitable management options for digested sludge from kraft pulp mills were found to be composting and incineration (when the latter was coupled with recycling ash to the cement industry). Landfill disposal was the worst option, presenting low performance in feasibility of implementation, risk of pollution, material and energy recovery. PMID:29298296

Dry Kraft Pulping at Ambient Pressure for Cost Effective Energy Saving and Pollution Deduction

Energy Technology Data Exchange (ETDEWEB)

Yulin Deng; Art Ragauskas

2012-08-28

Sponsored by the DOE Industrial Energy Efficiency Grand Challenge program, our research team at the Georgia Institute of Technology conducted laboratory studies and confirmed the concept of making wood pulp using a dry pulping technology. This technology is a new process different from any prior pulping technology used in Kraft and CTMP pulping. Three different kinds of dry pulping methods were investigated. (a) Dry Pulping at Atmospheric Pressure: The first one is to dry and bake the pretreated woodchips in a conventional oven at atmospheric pressure without the use of a catalyst. (b) Dry Pulping at Reduced Pressure: The second method is to dry the pretreated woodchips first in a vacuum oven in the presence of anthraquinone (AQ) as a pulping catalyst, followed by baking at elevated temperature. (c) Liquid Free Chemical Pulping, LFCP. The third method is to first remove the free water of pretreated woodchips, followed by dry pulping using a conventional Kraft pulping digester with AQ and triton as additives. Method one: Experimental results indicated that Dry Pulping at Atmospheric Pressure could produce pulp with higher brightness and lower bulk than conventional Kraft pulp. However, tensile strength of the acquired pulp is much lower than traditional Kraft pulp, and their Kappa number and energy consumption are higher than conventional Kraft pulp. By fully analyzing the results, we concluded that wood fibers might be damaged during the drying process at elevated temperature. The main reason for wood fiber damage is that a long drying time was used during evaporation of water from the woodchips. This resulted in an un-uniform reaction condition on the woodchips: the outside layer of the woodchips was over reacted while inside the woodchips did not reacted at all. To solve this problem, dry pulping at reduced pressure was investigated. Method two: To achieve uniform reaction throughout the entire reaction system, the water inside the pretreated woodchips was

A process for producing lignin and volatile compounds from hydrolysis liquor.

Science.gov (United States)

Khazraie, Tooran; Zhang, Yiqian; Tarasov, Dmitry; Gao, Weijue; Price, Jacquelyn; DeMartini, Nikolai; Hupa, Leena; Fatehi, Pedram

2017-01-01

Hot water hydrolysis process is commercially applied for treating wood chips prior to pulping or wood pellet production, while it produces hydrolysis liquor as a by-product. Since the hydrolysis liquor is dilute, the production of value-added materials from it would be challenging. In this study, acidification was proposed as a viable method to extract (1) furfural and acetic acid from hot water hydrolysis liquor and (2) lignin compounds from the liquor. The thermal properties of the precipitates made from the acidification of hydrolysis liquor confirmed the volatile characteristics of precipitates. Membrane dialysis was effective in removing inorganic salts associated with lignin compounds. The purified lignin compounds had a glass transition temperature (Tg) of 180-190 °C, and were thermally stable. The results confirmed that lignin compounds present in hot water hydrolysis liquor had different characteristics. The acidification of hydrolysis liquor primarily removed the volatile compounds from hydrolysis liquor. Based on these results, a process for producing purified lignin and precipitates of volatile compounds was proposed.

19 CFR 122.135 - When airline has in-bond liquor storeroom.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false When airline has in-bond liquor storeroom. 122.135 Section 122.135 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Aircraft Liquor Kits § 122.135 When airline has in-bond liquor storeroom. (a) Restocking. Liquor...

Perspectives for the electricity surplus generation at the paper and cellulose segment through the gasification of black liquor; Perspectivas para a geracao de excedentes de eletricidade no segmento de papel e celulose atraves da gaseificacao de lixivia

Energy Technology Data Exchange (ETDEWEB)

Velazquez, Silvia Maria Stortini Gonzalez [Universidade Presbiteriana Mackenzie, Sao Paulo, SP (Brazil). Escola de Engenharia]. E-mail: velazquez@mackenzie.com.br; Coelho, Suani Teixeira [CENBIO - Centro Nacional de Referencia em Biomassa, Sao Paulo, Sp (Brazil)]. E-mail: suani@iee.usp.br

2006-07-01

The pulp/paper segment is enclosed enters the most energointensive of the industrial sector. Its industries generate great part of the energy that consume from by-products of the process, but still are not self-sufficient. On the other hand, the difficulties of the industrial sector to the availability energy guarantee are well known, due to lack of trustworthiness of the electricity transmission and distribution. In this context, the increase of the self generation of electricity in the segment's plants certainly would go to collaborate for bigger flexibility in the Brazilian energy matrix, not only for the option of Demand Side Management, but even for the possibility of electricity excesses generation, as it is considered in this study. Thus, this work presents an economic and technique analysis of the energy cogeneration and the generation of electricity excesses in the pulp and paper segment and cellulose using more efficient technologies (although in development), as the black liquor gasification. The perspectives for the use of black liquor gasification systems and coupling of this unit to a gas turbine (BLGCC) are studied, with exploitation of the exhaustion gases in cogeneration systems. One is about technology in development phase in the industrialized countries and that it allows high conversion efficiency. They are, also, calculated the excesses generation costs, by means of the thermo economy, on the basis of the exergy concept, the most adjusted methodology to analyze cogeneration processes. Despite the biggest efficiency, the exceeding electricity, in some of the studied configurations, presented generation costs that do not reveal competitive with the sale's price of electricity, defined for the PROINFA, leaving evident the necessity of other mechanisms that make possible the implementation of new technologies, as the incorporation of the external factors and the carbon credits discouragement of the generation costs. In the pulp and paper

Clear Liquor Scrubbing with Anhydrite Production

International Nuclear Information System (INIS)

Hargrove, O. W.; Carey, T. R.; Lowell, P. S.; Meserole, F. B.; Rhudy, R. G.; Feeley, Thomas J.

1997-01-01

The objective of this project to develop an advanced flue gas desulfurization (FGD) process that has decreased capital and operating costs, higher SO 2 removal efficiency, and better by-product solids quality than existing, commercially available technology. A clear liquor process (which uses a scrubbing liquid with no solids) will be used to accomplish this objective rather than a slurry liquor process (which contains solids). This clear liquor scrubbing (CLS) project is focused on three research areas: (1) Development of a clear liquor scrubbing process that uses a clear solution to remove SO 2 from flue gas and can be operated under inhibited-oxidation conditions; (2) Development of an anhydrite process that converts precipitated calcium sulfite to anhydrous calcium sulfate (anhydrite); and (3) Development of an alkali/humidification process to remove HCl from flue gas upstream of the FGD system. The anhydrite process also can be retrofit into existing FGD systems to produce a valuable by-product as an alternative to gypsum. This fits well into another of FETC's PRDA objectives of developing an advanced byproduct recovery subsystem capable of transforming SO 2 into a useable byproduct or high-volume valuable commodities of interest. This paper describes the proposed processes, outlines the test approach, and preliminary Phase I test results

40 CFR 63.443 - Standards for the pulping system at kraft, soda, and semi-chemical processes.

Science.gov (United States)

2010-07-01

... Paper Industry § 63.443 Standards for the pulping system at kraft, soda, and semi-chemical processes. (a... operator of each pulping system using a semi-chemical or soda process subject to the requirements of this... kraft, soda, and semi-chemical processes. 63.443 Section 63.443 Protection of Environment ENVIRONMENTAL...

Spent sulfite liquor developments

Energy Technology Data Exchange (ETDEWEB)

Black, H H

1958-01-01

A review of methods of utilizing spent sulfite liquor, including evaporation and burning, fermentation to produce yeast or alcohol, production of vanillin and lignosulfonates, and use as a roadbinder.

Ground beetle populations near a kraft mill

Energy Technology Data Exchange (ETDEWEB)

Freitag, R.; Hastings, L.; Mercer, W.R.; Smith, A.

1973-02-01

Twenty species of ground beetles (Family Carabidae) and one species of carrion beetle (Family Silphidae) were collected in six stations east of a kraft paper mill in Thunder Bay, Ontario, from May to August, 1971. The beetle population decreased markedly towards the mill. There was no apparent statistical difference in size variation of specimens near the mill and those further away.

Precipitation and valorisation of lignin in South African kraft mill black liquor - first stages: Poster

CSIR Research Space (South Africa)

Namane, M

2013-10-01

Full Text Available Worldwide, the pulp and paper industry is in decline due to a number of factors such as high production costs, the growing utilization of electronic media that compete with print media and books, as well as pressure for the industry to be more...

Design of special facility for liquor irradiation

International Nuclear Information System (INIS)

Yao Shibin; Chen Zigen

1989-01-01

The design principle, physical scheme, technological process, construction and safety features of a special facility used for irradiating liquors is briefly described. 0.925 x 10 15 Bq cobalt source is used and the irradiation capacity for liquors approaches 10 t per day. The facility bears advantages of simple in construction, easy to operate, safe, reliable and efficient in source utilization

Influence of probiotics on rumen liquor characteristics and ...

African Journals Online (AJOL)

Probiotics has been noted to work synergistically with rumen microbes and improved rumen liquor characteristics. In this study, we investigated the effect of probiotics inclusion on rumen liquor characteristics (physical, chemical and fermentative qualities) and microbiology in WAD goats. In a completely randomised design, ...

Antraquinona e surfactante para otimizaçao do processo Kraft com Pinus Spp.

OpenAIRE

Mocelin, Ezequiel Zatoni

2013-01-01

A madeira de Pinus é atualmente a matéria-prima mais utilizada na obtenção de fibras longas para papel, juntamente com o processo Kraft pela sua versatilidade e por produzir fibras com boa resistência. As atuais perspectivas florestais apontam para uma escassez da madeira de Pinus para os diversos fins, seja para madeira processada, seja para celulose e papel. O processo Kraft tem como desvantagem o baixo rendimento em celulose, devido à solubilização não somente da lignina como também parte ...

Pulp and paper production from Spruce wood with kraft and ...

African Journals Online (AJOL)

STORAGESEVER

2010-03-15

Mar 15, 2010 ... optical properties of resultant paper were included to determine the properties of these pulp samples. ... pulping compounds in the kraft method are Na2S and .... Scanning electron microscope (SEM) measurement of pulp.

Feasibility of disposing waste glyphosate neutralization liquor with cement rotary kiln

International Nuclear Information System (INIS)

Bai, Y.; Bao, Y.B.; Cai, X.L.; Chen, C.H.; Ye, X.C.

2014-01-01

Highlights: • The waste neutralization liquor was injected directly into the kiln system. • No obvious effect on the quality of cement clinker. • The disposing method was a zero-discharge process. • The waste liquor can be used as an alternative fuel to reduce the coal consumption. - Abstract: The waste neutralization liquor generated during the glyphosate production using glycine-dimethylphosphit process is a severe pollution problem due to its high salinity and organic components. The cement rotary kiln was proposed as a zero discharge strategy of disposal. In this work, the waste liquor was calcinated and the mineralogical phases of residue were characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD). The mineralogical phases and the strength of cement clinker were characterized to evaluate the influence to the products. The burnability of cement raw meal added with waste liquor and the calorific value of waste liquor were tested to evaluate the influence to the thermal state of the kiln system. The results showed that after the addition of this liquor, the differences of the main phases and the strength of cement clinker were negligible, the burnability of raw meal was improved; and the calorific value of this liquor was 6140 J/g, which made it could be considered as an alternative fuel during the actual production

Feasibility of disposing waste glyphosate neutralization liquor with cement rotary kiln

Energy Technology Data Exchange (ETDEWEB)

Bai, Y.; Bao, Y.B.; Cai, X.L.; Chen, C.H. [College of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009 (China); State Key Laboratory of Materials-Oriented Chemical Engineering, Nanjing Tech University, Nanjing 210009 (China); Ye, X.C., E-mail: yexuchu@njtech.edu.cn [College of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009 (China); State Key Laboratory of Materials-Oriented Chemical Engineering, Nanjing Tech University, Nanjing 210009 (China)

2014-08-15

Highlights: • The waste neutralization liquor was injected directly into the kiln system. • No obvious effect on the quality of cement clinker. • The disposing method was a zero-discharge process. • The waste liquor can be used as an alternative fuel to reduce the coal consumption. - Abstract: The waste neutralization liquor generated during the glyphosate production using glycine-dimethylphosphit process is a severe pollution problem due to its high salinity and organic components. The cement rotary kiln was proposed as a zero discharge strategy of disposal. In this work, the waste liquor was calcinated and the mineralogical phases of residue were characterized by scanning electron microscope (SEM) and X-ray diffraction (XRD). The mineralogical phases and the strength of cement clinker were characterized to evaluate the influence to the products. The burnability of cement raw meal added with waste liquor and the calorific value of waste liquor were tested to evaluate the influence to the thermal state of the kiln system. The results showed that after the addition of this liquor, the differences of the main phases and the strength of cement clinker were negligible, the burnability of raw meal was improved; and the calorific value of this liquor was 6140 J/g, which made it could be considered as an alternative fuel during the actual production.

Kraft lignin chain extension chemistry via propargylation, oxidative coupling, and Claisen rearrangement.

Science.gov (United States)

Sen, Sanghamitra; Sadeghifar, Hasan; Argyropoulos, Dimitris S

2013-10-14

Despite its aromatic and polymeric nature, the heterogeneous, stochastic, and reactive characteristics of softwood kraft lignin seriously limit its potential for thermoplastic applications. Our continuing efforts toward creating thermoplastic lignin polymers are now focused at exploring propargylation derivatization chemistry and its potential as a versatile novel route for the eventual utilization of technical lignins with a significant amount of molecular control. To do this, we initially report the systematic propargylation of softwood kraft lignin. The synthesized derivatives were extensively characterized with thermal methods (DSC, TGA), (1)H, (13)C, and quantitative (31)P NMR and IR spectroscopies. Further on, we explore the versatile nature of the lignin pendant propargyl groups by demonstrating two distinct chain extension chemistries; the solution-based, copper-mediated, oxidative coupling and the thermally induced, solid-state, Claissen rearrangement polymerization chemistries. Overall, we show that it is possible to modulate the reactivity of softwood kraft lignin via a combination of methylation and chain extension providing a rational means for the creation of higher molecular weight polymers with the potential for thermoplastic materials and carbon fibers with the desired control of structure-property relations.

40 CFR 63.446 - Standards for kraft pulping process condensates.

Science.gov (United States)

2010-07-01

... National Emission Standards for Hazardous Air Pollutants from the Pulp and Paper Industry § 63.446...; (3) Each evaporator system condensate from: (i) The vapors from each stage where weak liquor is introduced (feed stages); and (ii) Each evaporator vacuum system for each stage where weak liquor is...

Effects of a Chitosan Coating Layer on the Surface Properties and Barrier Properties of Kraft Paper

Directory of Open Access Journals (Sweden)

Shanhui Wang

2016-01-01

Full Text Available Biodegradable chitosan can be applied as a coating on the surface of kraft paper in order to improve its barrier properties against water vapor and air. The food packaging industry can benefit from the addition of chitosan to its current packaging, and in turn reduce pollution from plastic packaging plants. This paper discusses the film formation of chitosan, the permeability of paper coated with a chitosan layer, and the influence on the paper’s surface and barrier properties under different process conditions. SEM (scanning electron microscope, AFM (atomic force microscope, ATR-FTIR (Fourier transmission infrared spectroscope with attenuated total reflection, and PDA (penetration dynamics analysis were used to analyze the properties of chitosan’s film formation and permeability. A controlled experiment showed that the chitosan layer was smoother than the surface of the uncoated kraft paper, had better film formation, and that there was no chitosan penetration through the kraft paper. The barrier properties against water vapor were strongest when there was a higher concentration of chitosan solution at the optimum pH, stirring speed, and those with a thicker coating on the kraft paper.

The recovery boiler advisor. Combination of practical experience and advanced thermodynamic modelling

Energy Technology Data Exchange (ETDEWEB)

Backman, R. [Aabo Akademi, Turku (Finland); Eriksson, G. [LTH/RWTH (Germany); Sundstroem, K. [Tampella Power Oy, Tampere (Finland)

1996-12-31

The Aabo Advisor is a computer based program intended to provide information about the high temperature ash and fluegas chemistry in pulping spent black liquor recovery boilers of kraft pulp mills. The program can be used for predictions of a variety of furnace and flue gas phenomena, such as fireside fouling of the heat exchanger surfaces caused by the flue gas particulate matter, emissions of SO{sub 2}(g), HCl(g) and NO{sub x}(g) with the flue gas etc. The program determines the composition of the fluegas as well as the amount and composition of the two typical fly ash fractions found in recovery boiler fluegases, the condensed fly ash particles and the carry over particles. These data are used for calculating the melting behavior of the fly ash present at different locations in the boiler and this characteristic behavior is used for the fireside fouling predictions. The program may also be used for studying how different mill processes affecting the black liquor composition affects on the fireside chemistry of the recovery boiler. As input data for the calculations only a few boiler operation parameters and the composition of the black liquor is required. The calculations are based on a one-dimensional, multi-stage chemistry model where both thermodynamic equilibrium calculations and stoichiometric material balances are used. The model calculates at first the chemistry in the lower furnace and smelt after which it moves to the upper furnace and the radiative parts of the fluegas channel. As the last block the program calculates the chemistry in the convective part, the electrostatic precipitator cath and stack. The results from each block are presented in tables, key numbers and melt curves representing the fluegas or fly ash fraction present at each location

The recovery boiler advisor. Combination of practical experience and advanced thermodynamic modelling

Energy Technology Data Exchange (ETDEWEB)

Backman, R [Aabo Akademi, Turku (Finland); Eriksson, G [LTH/RWTH (Germany); Sundstroem, K [Tampella Power Oy, Tampere (Finland)

1997-12-31

The Aabo Advisor is a computer based program intended to provide information about the high temperature ash and fluegas chemistry in pulping spent black liquor recovery boilers of kraft pulp mills. The program can be used for predictions of a variety of furnace and flue gas phenomena, such as fireside fouling of the heat exchanger surfaces caused by the flue gas particulate matter, emissions of SO{sub 2}(g), HCl(g) and NO{sub x}(g) with the flue gas etc. The program determines the composition of the fluegas as well as the amount and composition of the two typical fly ash fractions found in recovery boiler fluegases, the condensed fly ash particles and the carry over particles. These data are used for calculating the melting behavior of the fly ash present at different locations in the boiler and this characteristic behavior is used for the fireside fouling predictions. The program may also be used for studying how different mill processes affecting the black liquor composition affects on the fireside chemistry of the recovery boiler. As input data for the calculations only a few boiler operation parameters and the composition of the black liquor is required. The calculations are based on a one-dimensional, multi-stage chemistry model where both thermodynamic equilibrium calculations and stoichiometric material balances are used. The model calculates at first the chemistry in the lower furnace and smelt after which it moves to the upper furnace and the radiative parts of the fluegas channel. As the last block the program calculates the chemistry in the convective part, the electrostatic precipitator cath and stack. The results from each block are presented in tables, key numbers and melt curves representing the fluegas or fly ash fraction present at each location

KRAFT PULPING CHARACTERISTICS OF THREE MOROCCAN EUCALYPTI. PART 2. COMPARISON OF THE GUAIACYL FRACTION OF THE NATIVE LIGNINS BY A NOVEL METHOD

Directory of Open Access Journals (Sweden)

Ericka F. Alves,

2012-02-01

Full Text Available In Part 1 of this series it was observed that one of the eucalypti (EGC 39 was more reactive than the other two in kraft and soda-AQ (SAQ cooking. However, the lignin in EGC 39 contained equal or less syringyl (S units than the other two eucalypti. In the present research an attempt was made to compare the guaiacyl (G fraction of the three lignins. The approach was to use SAQ treatment to cleave β-O-4 bonds in dimeric units containing uncondensed guaiacyl A-rings (those rearranging to quinone methides. The coniferyl alcohol, vinylguaiacol and isoeugenol generated from β-O-4 cleavage are then trapped as dimers by ethylguaiacol that is included in the SAQ liquor. Research with sugar maple (Acer saccharum showed that the estimate of these structures (uncondensed G-β-O-4 by this approach was in close agreement with traditional but more tedious methods such as permanganate oxidation and 31P NMR. It was also shown that the lignin in the EGC 39 hybrid contained a higher concentration of uncondensed G-β-O-4 structures than the other two eucalypti lignins.

Chemical by-products from spent sulfite liquors

Energy Technology Data Exchange (ETDEWEB)

Whitmore, Jr, L M; Wiley, A J

1958-01-01

Current practices for recovering sugars, lignosulfonates, ethanol and feed yeast and product uses are reviewed. A process for separating sugars is described in which the sulfite liquor is spray dried and refluxed with acetone containing a concentrated H/sub 2/SO/sub 4/ catalyst, and the di-acetone sugar derivatives are filtered or centrifuged from the acetone insolubles. Recovery of guaiacyl and syringyl derivatives from the lignosulfonate portion of the liquor is discussed.

Discrimination between authentic and adulterated liquors by near-infrared spectroscopy and ensemble classification

Science.gov (United States)

Chen, Hui; Tan, Chao; Wu, Tong; Wang, Li; Zhu, Wanping

2014-09-01

Chinese liquor is one of the famous distilled spirits and counterfeit liquor is becoming a serious problem in the market. Especially, age liquor is facing the crisis of confidence because it is difficult for consumer to identify the marked age, which prompts unscrupulous traders to pose off low-grade liquors as high-grade liquors. An ideal method for authenticity confirmation of liquors should be non-invasive, non-destructive and timely. The combination of near-infrared spectroscopy with chemometrics proves to be a good way to reach these premises. A new strategy is proposed for classification and verification of the adulteration of liquors by using NIR spectroscopy and chemometric classification, i.e., ensemble support vector machines (SVM). Three measures, i.e., accuracy, sensitivity and specificity were used for performance evaluation. The results confirmed that the strategy can serve as a screening tool applied to verify adulteration of the liquor, that is, a prior step used to condition the sample to a deeper analysis only when a positive result for adulteration is obtained by the proposed methodology.

Liquor licences issued to Australian schools.

Science.gov (United States)

Ward, Bernadette M; Kippen, Rebecca; Munro, Geoffrey; Buykx, Penny; McBride, Nyanda; Wiggers, John; Clark, Madeline

2017-08-01

Children's positive socialisation to alcohol is associated with early initiation of drinking and alcohol-related harm in adult life. Internationally, there have been reports of adults' alcohol consumption at school events in the presence of children. The aim of this research was to identify the conditions under which Australian schools are required to apply for a liquor licence and the associated prevalence of liquor licences for these events where children were likely to be present. A document review was conducted to examine temporary liquor licensing legislation. Quantitative analysis was used to examine relevant licensing data. Coding criteria was developed to determine school type, student year levels and the likely presence of children. Four jurisdictions provided data on 1817 relevant licences. The average annual licences/100 schools was highest amongst Independent schools followed by Catholic and public (government) schools. The rates were highest in Queensland and Victoria where children were present at 61% and 32% of events respectively. While there are legislative differences across jurisdictions, the prevalence of adults' alcohol use at school events in the presence of children may reflect the various education department policies and principals' and school communities' beliefs and attitudes. Licences are not required for all events where liquor is consumed so the prevalence of adults' use of alcohol at school events is likely to be higher than our analyses imply. Such practices may undermine teaching about alcohol use in the school curriculum and health promotion efforts to develop alcohol-free events when children are present.

Engineering study: disposition of terminal liquors for interim storage

International Nuclear Information System (INIS)

Metz, W.P.; Ogren, W.E.

1975-02-01

Eight alternative processes were chosen as being technologically feasible within the time frame dictated by budgeting procedures and terminal liquor availability. Solidified waste products acceptable for single-shell tank storage were assumed to be placed in available single-shell tanks. Double-shell tanks were used only for the more mobile terminal liquors or semi-solid mush products. The mush, chemical neutralization, and clay in-tank processes offer potential savings of tens of millions of dollars over double-shell tank storage of terminal liquors. In order to achieve this cost savings, the process development and demonstration must be completed prior to the beginning of double-shell tank construction (Dec. 1976) expected to be funded from a fiscal year 1977 line item. Budgeting for these additional double-shell tanks must proceed since the processing options discussed here are not yet available and may not prove to be available at the required time. This study indicates the following topics for additional study: Process technology development to achieve interim storage of terminal liquor products receives the greatest emphasis as a means of reducing capital expenditures. Interim storage product criteria, waste inventory, and conversion to final form require definition to allow comparison of the alternatives for disposition of terminal liquors. The pseudotechnical nature of product acceptability criteria is important to the evaluation of the partial neutralization and aluminum removal alternatives. More accurate estimates of terminal liquor quantity and composition are required to give a sound technical basis for choosing the appropriate processing alternative. Retrieval and reprocessing operations may affect the comparisons presented by this study

Experimental Studies on the Hydrotreatment of Kraft Lignin to Aromatics and Alkylphenolics Using Economically Viable Fe-Based Catalysts

NARCIS (Netherlands)

Agarwal, Shilpa; Chowdari, Ramesh Kumar; Hita, Idoia; Heeres, Hero Jan

Limonite, a low-cost iron ore, was investigated as a potential hydrotreatment catalyst for kraft lignin without the use of an external solvent (batch reactor, initial H-2 pressure of 100 bar, 4 h). The best results were obtained at 450 degrees C resulting in 34 wt % of liquefied kraft lignin (lignin

27 CFR 31.42 - Restaurants serving liquors with meals.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Restaurants serving... Part Certain Organizations, Agencies, and Persons § 31.42 Restaurants serving liquors with meals. Proprietors of restaurants and other persons who serve liquors with meals to paying customers, even if no...

Biological treatment of the liquid effluents of a paper industry

International Nuclear Information System (INIS)

Mejia, Juan Felipe; Ramirez, Gladys Eugenia; Arias Zabala, Mario

2001-01-01

The objective of this paper is to determine the effect of the microorganisms Candida utilis and Candida tropicalis in the reduction of the chemical oxygen demand (COD) of the liquid effluents of a producing factory of paper kraft type, by means of fermentations made to pH of 5 and a 30 centigrade degrees during 6 days. The biological processing is preceded by a physicochemical process of directed acidulation to reduce pH of the effluent (liquor black) from its initial value, of approximately 13, to 5, in order to it is adapted for the growth of yeast. In this process, which forms precipitated, that is necessary to eliminate by centrifugation and filtration to facilitate the growth of the microorganisms, with is obtained one first removal of the COD of the order of 70 %. With the biological processing obtains for both yeasts a percentage of removal of 45 -50% of the COD surplus. The total removal of the COD, that is to say, obtained with the pre-cure and the fermentation it is of the order of 84% for the yeast. Additionally the possibility studied of implementing some complementary procedures to the biological processing, with a view to obtaining greater growth of yeast in the black liquor and thus obtaining additional reductions in the OCD of the same one

Measurement of cellulose content, Kraft pulp yield and basic density ...

African Journals Online (AJOL)

Previous descriptions of multisite and multispecies near infra-red (NIR) spectroscopic calibrations for predicting cellulose content (CC) and Kraft pulp yield (KPY) in eucalypt woodmeal demonstrated that large, single calibrations provide precise predictions for a wide range of sites and species. These have since been used ...

Relationship between lignin structure and delignification degree in Pinus pinaster kraft pulps.

Science.gov (United States)

Baptista, C; Robert, D; Duarte, A P

2008-05-01

This study examines the structure of residual and dissolved lignins from Pinus pinaster pulps obtained at different degrees of delignification by laboratory conventional kraft pulping. The cooking H factor was varied from 85 to 8049. The residual and dissolved lignin samples were characterised by elemental analysis, residual carbohydrate content, permanganate oxidation and 13C NMR spectroscopy. The reflectance factor of the pulps was also determined in order to tentatively correlate the delignification degree and residual lignin structure with the pulp colour. The obtained results confirmed that the delignification degree increases the condensation of the lignin structure, which might have an influence upon the observed increased pulp colour. The lack of selectivity of kraft pulping process in the case of more delignified pulps was also shown.

Techno-Economic Analysis of the Optimum Softwood Lignin Content for the Production of Bioethanol in a Repurposed Kraft Mill

Directory of Open Access Journals (Sweden)

Shufang Wu

2014-09-01

Full Text Available Kraft pulping is one possible pretreatment for softwood to economically produce bioethanol. This work evaluates the techno-economic potential of using the kraft process for producing bioethanol from softwoods in a repurposed or co-located kraft mill. Pretreated loblolly pine was enzymatically hydrolyzed at low enzyme dosages of 5 and 10 FPU/g of substrate. Pretreated residue with 13% lignin content had the highest sugar recovery, 32.7% and 47.7% at 5 and 10 FPU/g, respectively. The pretreated residues were oxygen delignified and refined. In all cases, oxygen delignification improved sugar recovery, while refining was mostly effective for pulps with high lignin content. At 5 FPU/g, the sugar recovery for all kraft pulps was 51 to 53% with oxygen delignification and refining. Increasing the enzyme dosage to 10 FPU/g increased the sugar recovery for these pulps to greater than 60%. Economic analysis for the pulps with different initial lignin content showed that kraft pulps with an initial lignin content of 6.7% with oxygen delignification had an ethanol yield of 285 L/ODt wood and the lowest total production cost of $0.55/L. Pulps with initial lignin content of 18.6% had a total production cost of $0.64/L with an ethanol yield of 264 L/ODt wood.

Sulphate removal from uraniferous liquors

International Nuclear Information System (INIS)

Berger, B.

1983-01-01

A process for the recovery of uranium from liquor resulting from the attack of sulphur containing uraniferous ores by an alkaline solution of sodium carbonate and/or sodium bicarbonate is claimed. An ion exchange resin is used to separate the uranium from the solution of sodium carbonate and/or bicarbonate and sodium sulphate. The ion exchange resin is then eluted with a solution of ammonium carbonate and/or bicarbonate to provide an eluate containing ammonium uranyl tricarbonate, ammonium carbonate and/or bicarbonate and ammonium sulphate. The eluate is heated to boiling to convert the ammonium uranyl tricarbonate to ammonium uranate and/or diuranate. Ammonia, carbon dioxide and water vapor are released. The precipitated ammonium uranate and/or diuranate is separated from the remaining liquor and calcined to give uranium trioxide

New microbial resource: microbial diversity, function and dynamics in Chinese liquor starter.

Science.gov (United States)

Huang, Yuhong; Yi, Zhuolin; Jin, Yanling; Zhao, Yonggui; He, Kaize; Liu, Dayu; Zhao, Dong; He, Hui; Luo, Huibo; Zhang, Wenxue; Fang, Yang; Zhao, Hai

2017-11-06

Traditional Chinese liquor (Baijiu) solid state fermentation technology has lasted for several thousand years. The microbial communities that enrich in liquor starter are important for fermentation. However, the microbial communities are still under-characterized. In this study, 454 pyrosequencing technology was applied to comprehensively analyze the microbial diversity, function and dynamics of two most-consumed liquor starters (Jiang- and Nong-flavor) during production. In total, 315 and 83 bacterial genera and 72 and 47 fungal genera were identified in Jiang- and Nong-flavor liquor starter, respectively. The relatively high diversity was observed when the temperature increased to 70 and 62 °C for Jiang- and Nong-flavor liquor starter, respectively. Some thermophilic fungi have already been isolated. Microbial communities that might contribute to ethanol fermentation, saccharification and flavor development were identified and shown to be core communities in correlation-based network analysis. The predictively functional profile of bacterial communities showed significant difference in energy, carbohydrate and amino acid metabolism and the degradation of aromatic compounds between the two kinds of liquor starters. Here we report these liquor starters as a new functionally microbial resource, which can be used for discovering thermophilic and aerobic enzymes and for food and feed preservation.

Effect of Urea Addition on Soda Pulping of Oak Wood

OpenAIRE

Cho, Nam-Seok; Matsumoto, Yuji; Cho, Hee-Yeon; Shin, Soo-Jeong; Oga, Shoji

2008-01-01

Many studies have been conducted to find a sulfur-free additive for alkaline pulping liquors that would have an effect similar to that of sulfide in kraft pulping. Some reagents that partially fulfill this role have been found, but they are too expensive to be used in the quantities required to make them effective. As an alternative method to solve air pollution problem and difficulty of pulp bleaching of kraft pulping process, NaOH-Urea pulping was applied. The properties of NaOH-Urea pul...

Rapid identification of Chinese Sauce liquor from different fermentation positions with FT-IR spectroscopy

Science.gov (United States)

Li, Changwen; Wei, Jiping; Zhou, Qun; Sun, Suqin

2008-07-01

FT-IR and two-dimensional correlation spectroscopy (2D-IR) technology were applied to discriminate Chinese Sauce liquor from different fermentation positions (top, middle and bottom of fermentation cellar) for the first time. The liquors at top, middle and bottom of fermentation cellar, possessed the characteristic peaks at 1731 cm -1, 1733 cm -1 and 1602 cm -1, respectively. In the 2D correlation infrared spectra, the differences were amplified. A strong auto-peak at 1725 cm -1 showed in the 2D spectra of the Top Liquor, which indicated that the liquor might contain some ester compounds. Different from Top Liquor, three auto-peaks at 1695, 1590 and 1480 cm -1 were identified in 2D spectra of Middle Liquor, which were the characteristic absorption of acid, lactate. In 2D spectra of Bottom Liquor, two auto-peaks at 1570 and 1485 cm -1 indicated that lactate was the major component. As a result, FT-IR and 2D-IR correlation spectra technology provided a rapid and effective method for the quality analysis of the Sauce liquor.

Effects of Alkali Treatment and Polyisocyanate Crosslinking on the Mechanical Properties of Kraft Fiber-Reinforced Unsaturated Polyester Composites

Directory of Open Access Journals (Sweden)

Zhenhua Gao

2014-08-01

Full Text Available The effects of alkali treatment and polyisocyanate crosslinking on the mechanical properties of kraft fiber-reinforced UPE composites were investigated by means of tensile evaluation, SEM analysis, and XRD analysis. The results indicated that the alkali treatment decreased the tensile strength of the prepared composite before aging from 121 MPa to 97 MPa due to the decreased degree of crystallinity of the alkali-treated kraft fiber. Polyisocyanate crosslinking could apparently improve the mechanical properties and stability in terms of a 43% increase of non-aged tensile strength and 52% increase of hydrothermal-aged tensile strength compared with the controlled composite without crosslinking modification, which was attributable to the formation of strong chemical bonding between the interfaces of kraft fiber and polyester.

Yeast community associated with the solid state fermentation of traditional Chinese Maotai-flavor liquor.

Science.gov (United States)

Wu, Qun; Chen, Liangqiang; Xu, Yan

2013-09-02

Yeasts are the most important group of microorganisms contributing to liquor quality in the solid-state fermentation process of Chinese Maotai-flavor liquor. There occurred a complex yeast community structure during this process, including stages of Daqu (the starter) making, stacking fermentation on the ground and liquor fermentation in the pits. In the Daqu making stage, few yeast strains accumulated. However, the stacking fermentation stage accumulated nine yeast species with different physio-biochemical characteristics. But only four species kept dominant until liquor fermentation, which were Zygosaccharomyces bailii, Saccharomyces cerevisiae, Pichia membranifaciens, and Schizosaccharomyces pombe, implying their important functions in liquor making. The four species tended to inhabit in different locations of the stack and pits during stacking and liquor fermentation, due to the condition heterogeneity of the solid-state fermentation, including the different fermentation temperature profiles and oxygen density in different locations. Moreover, yeast population was much larger in the upper layer than that in the middle and bottom layers in liquor fermentation, which was in accordance with the profile of reducing sugar consumption and ethanol production. This was a systematical investigation of yeast community structure dynamics in the Maotai-flavor liquor fermentation process. It would be of help to understand the fermentative mechanism in solid-state fermentation for Maotai-flavor liquor. © 2013.

Characterization of solid wastes from kraft pulp industry for ceramic materials development purposes

International Nuclear Information System (INIS)

Rodrigues, L.R.; Francisco, M.A.C.O.; Sagrillo, V.P.D.; Louzada, D.M.; Entringer, J.M.S.

2016-01-01

The Kraft pulp industry generates a large amount of solid wastes. Due this large quantity, the target of this study is characterize inorganic solid wastes, dregs, grits and lime mud, from the step of reagents recovery of Kraft process, aiming evaluate the potentiality of their use as alternative raw material on development of ceramic materials. Initially, the wastes were dried and ground, then they were subjected to the following characterization techniques: pH analysis, particle size analysis, X ray fluorescence, X ray diffraction, differential thermal analysis and thermogravimetric analysis and scanning electron microscopy. According to the results, it may be concluded that these wastes could be used as raw material in production of red ceramic and luting materials. (author)

Characterization of solid wastes from kraft pulp industry for ceramic materials development purposes; Caracterizacao de residuos solidos da industria de celulose tipo kraft visando sua aplicacao no desenvolvimento de materiais ceramicos

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, L.R.; Francisco, M.A.C.O.; Sagrillo, V.P.D.; Louzada, D.M.; Entringer, J.M.S. [Instituto Federal do Espirito Santo (IFES), Vitoria, ES (Brazil)

2016-07-01

The Kraft pulp industry generates a large amount of solid wastes. Due this large quantity, the target of this study is characterize inorganic solid wastes, dregs, grits and lime mud, from the step of reagents recovery of Kraft process, aiming evaluate the potentiality of their use as alternative raw material on development of ceramic materials. Initially, the wastes were dried and ground, then they were subjected to the following characterization techniques: pH analysis, particle size analysis, X ray fluorescence, X ray diffraction, differential thermal analysis and thermogravimetric analysis and scanning electron microscopy. According to the results, it may be concluded that these wastes could be used as raw material in production of red ceramic and luting materials. (author)

Properties and Possible Applications for Lignin Streams Obtained from Rice Straw Processing

DEFF Research Database (Denmark)

Mussatto, Solange I.

This study aimed to evaluate the chemical and physical properties of lignin streams recovered from rice straw processing and to study the extraction of antioxidant phenolic compounds from these materials. The evaluated samples included two different cellulignin fermentation residues (FR’s) and an......This study aimed to evaluate the chemical and physical properties of lignin streams recovered from rice straw processing and to study the extraction of antioxidant phenolic compounds from these materials. The evaluated samples included two different cellulignin fermentation residues (FR......’s) and an acid-precipitated lignin from alkaline-deacetylated black liquor (DBLL). For comparison, a standard lignin sample (Kraft lignin, from Sigma-Aldrich) was also assayed. Besides providing a better understanding about such materials, the obtained results made also possible to propose some potential...

Discrimination of Chinese Sauce liquor using FT-IR and two-dimensional correlation IR spectroscopy

Science.gov (United States)

Sun, Su-Qin; Li, Chang-Wen; Wei, Ji-Ping; Zhou, Qun; Noda, Isao

2006-11-01

We applied the three-step IR macro-fingerprint identification method to obtain the IR characteristic fingerprints of so-called Chinese Sauce liquor (Moutai liquor and Kinsly liquor) and a counterfeit Moutai. These fingerprints can be used for the identification and discrimination of similar liquor products. The comparison of their conventional IR spectra, as the first step of identification, shows that the primary difference in Sauce liquor is the intensity of characteristic peaks at 1592 and 1225 cm -1. The comparison of the second derivative IR spectra, as the second step of identification, shows that the characteristic absorption in 1400-1800 cm -1 is substantially different. The comparison of 2D-IR correlation spectra, as the third and final step of identification, can discriminate the liquors from another direction. Furthermore, the method was successfully applied to the discrimination of a counterfeit Moutai from the genuine Sauce liquor. The success of the three-step IR macro-fingerprint identification to provide a rapid and effective method for the identification of Chinese liquor suggests the potential extension of this technique to the identification and discrimination of other wine and spirits, as well.

Development of blueberry liquor: influence of distillate, sweetener and fruit quantity.

Science.gov (United States)

Caldeira, Ilda; Lopes, Daniel; Delgado, Teresa; Canas, Sara; Anjos, Ofélia

2018-02-01

In this work different formulations of blueberry liquor were tested and characterised based on their physico-chemical and sensory characteristics. Three factors were evaluated: the distillate used to produce the liquor (wine spirit or grape marc spirit); the sweetener (white sugar or honey) and the fruit quantity (two doses). For each liquor, pH, total acidity, dry soluble solids content, dry extract, alcoholic strength, reducing sugars, colour intensity, methanol content, acetaldehyde and fusel alcohols were determined. Sensory tests were carried out with a trained panel. The three factors studied significantly influenced the physico-chemical features of the liquors, being the quantity of fruit the most discriminating factor, except for the volatile compounds which were mainly influenced by the distillate. As regards the sensory analysis, it was found that the most appreciated liquor was that prepared with wine spirit, sugar and a lower dose of blueberry, and the less appreciated formulation was the one made with grape marc spirit, honey and a lower quantity of blueberry. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Characterization of Chinese liquor aroma components during aging process and liquor age discrimination using gas chromatography combined with multivariable statistics

Science.gov (United States)

Xu, M. L.; Yu, Y.; Ramaswamy, H. S.; Zhu, S. M.

2017-01-01

Chinese liquor aroma components were characterized during the aging process using gas chromatography (GC). Principal component and cluster analysis (PCA, CA) were used to discriminate the Chinese liquor age which has a great economic value. Of a total of 21 major aroma components identified and quantified, 13 components which included several acids, alcohols, esters, aldehydes and furans decreased significantly in the first year of aging, maintained the same levels (p > 0.05) for next three years and decreased again (p counterfeit and defective products.

Interactions of Kraft lignin and wheat gluten during biomaterial processing: evidence for the role of phenolic groups.

Science.gov (United States)

Kaewtatip, Kaewta; Menut, Paul; Auvergne, Remi; Tanrattanakul, Varaporn; Morel, Marie-Helene; Guilbert, Stephane

2010-04-14

The chemical interactions between Kraft lignin and wheat gluten under processing conditions were investigated by determining the extent of the protein network formation. To clarify the role of different chemical functions found in lignin, the effect of Kraft lignin was compared with that of an esterified lignin, in which hydroxyl groups had been suppressed by esterification, and with a series of simple aromatics and phenolic structures with different functionalities (conjugated double bonds, hydroxyl, carboxylic acid, and aldehyde). The protein solubility was determined by using the Kjeldahl method. The role of the hydroxyl function was assessed by the significantly lower effect of esterified lignin. The importance of the phenolic radical scavenging structure is evidenced by the effect of guaiacol, which results in a behavior similar to that of the Kraft lignin. In addition, the significant effect of conjugated double bonds on gluten reactivity, through nucleophilic addition, was demonstrated.

Application of Alkaline Ionic Liquids in the Pretreatment Process of Eucalyptus Kraft Pulping

Directory of Open Access Journals (Sweden)

Yi Hou

2016-09-01

Full Text Available In order to explore the potential application of green solvent ionic liquids (ILs in the kraft pulping process, eucalyptus wood was pretreated by [Mmim]DMP before normal pulping. The results showed that materials pretreated shortly by the ionic liquid had a higher yield and viscosity coupled with a lower potassium permanganate value and residual lignin content in the pulp, as a result of the cooking process. It was also inferred that alkaline [Mmim]DMP pretreatment could dissolve lignin effectively from fiber to result in a stronger binding force and more entangled properties. Paper tensile and burst strength were improved by about 40% and 60%, respectively. These results provide a new way for eucalyptus to be utilized in the kraft pulping process.

Mystery behind Chinese liquor fermentation

NARCIS (Netherlands)

Jin, Guangyuan; Zhu, Yang; Xu, Yan

2017-01-01

Background Chinese liquor, a very popular fermented alcoholic beverage with thousands of years’ history in China, though its flavour formation and microbial process have only been partly explored, is facing the industrial challenge of modernisation and standardisation for food quality and safety as

Social capital, the miniaturisation of community and consumption of homemade liquor and smuggled liquor during the past year. A population-based study.

Science.gov (United States)

Lindström, Martin

2005-12-01

To study the impact of social participation, trust and the miniaturisation of community, i.e. high social participation/low trust, on consumption of homemade liquor and smuggled liquor during the past year. The Scania 2000 public health survey is a cross-sectional, postal questionnaire study. A total of 13,604 persons aged 18-80 years were included. A logistic regression model was used to investigate the association between the social capital variables and illegal alcohol consumption. The multivariate analyses analysed the importance of confounders (age, country of origin, education and economic stress) on the differences in consumption of homemade and smuggled liquor according to the social capital variables. A 28.2% proportion of all men and 14.9% of all women had consumed homemade liquor during the past year. The proportions who had consumed smuggled liquor during the past year were even higher, 40.1% among men and 21.4% among women. Both forms of illegal alcohol consumption were significantly positively associated with social participation and negatively associated with trust. The miniaturisation of community category, i.e. high social participation/low trust, had significantly higher risks of consumption during the past year of the consumption of both forms of illegally provided alcohol compared to the high social capital (high social participation/high trust) category, while the low social participation/high trust category had significantly lower risks. High social participation combined with low trust is positively associated with consumption of illegally provided alcohol. The results have implications for alcohol prevention programs, because structural/social factors that may hinder information and norms concerning illegal alcohol have been identified in this study.

Impact of chocolate liquor on vascular lesions in apoE-knockout mice.

Science.gov (United States)

Yazdekhasti, Narges; Brandsch, Corinna; Hirche, Frank; Kühn, Julia; Schloesser, Anke; Esatbeyoglu, Tuba; Huebbe, Patricia; Wolffram, Siegfried; Rimbach, Gerald; Stangl, Gabriele I

2017-10-15

Cocoa polyphenols are thought to reduce the risk of cardiovascular diseases. Thus, cocoa-containing foods may have significant health benefits. Here, we studied the impact of chocolate liquor on vascular lesion development and plaque composition in a mouse model of atherosclerosis. Apolipoprotein E (apoE)-knockout mice were assigned to two groups and fed a Western diet that contained 250 g/kg of either chocolate liquor or a polyphenol-free isoenergetic control paste for 16 weeks. In addition to fat, protein, and fibers, the chocolate liquor contained 2 g/kg of polyphenols. Compared with the control group, mice fed the chocolate liquor had larger plaque areas in the descending aorta and aortic root, which were attributed to a higher mass of vascular smooth muscle cells (VSMCs) and collagen. Vascular lipid deposits and calcification areas did not differ between the two groups. The aortic tissue level of interleukin-6 (IL-6) mRNA was 5-fold higher in the mice fed chocolate liquor than in the control mice. Chocolate-fed mice exhibited an increased hepatic saturated to polyunsaturated fatty acid ratio than the controls. Although the chocolate liquor contained 14 µg/kg of vitamin D 2 , the chocolate liquor-fed mice did not have measurable 25-hydroxyvitamin D 2 in the serum. These mice even showed a 25% reduction in the level of 25-hydroxyvitamin D 3 compared with the control mice. Overall, present data may contribute to our understanding how chocolate constituents can impact vascular lesion development. © 2017 The Author(s). Published by Portland Press Limited on behalf of the Biochemical Society.

De kristallisatie-methode bij het onderzoek van de liquor cerebro-spinalis

NARCIS (Netherlands)

Wittermans, Aafko Willinge

1941-01-01

Ongeveer twaalfhonderd liquores zijn volgens een in de kliniek nog weinig bekende zeer eenvoudige methode van onderzoek van den Roemeenschen Hoogleraar TOMESCO onderzocht. Deze methode berust op het beoordeelen van het kristalbeeld dat ontstaat bij het indampen van druppels sterk verdunde liquor

19 CFR 122.134 - When airline does not have in-bond liquor storeroom.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false When airline does not have in-bond liquor storeroom. 122.134 Section 122.134 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY AIR COMMERCE REGULATIONS Aircraft Liquor Kits § 122.134 When airline does not have in-bond liquor storeroom. (a...

Immunostimulation and yellow head virus (YHV) disease resistance induced by a lignin-based pulping by-product in black tiger shrimp (Penaeus monodon Linn.).

Science.gov (United States)

Srisapoome, Prapansak; Hamano, Kaoru; Tsutsui, Isao; Iiyama, Kenji

2018-01-01

Yellow head virus (YHV) is classified as one of the most serious pathogens causing a harmful disease in many penaeids, especially black tiger shrimp (Penaeus monodon), with high economic loss. To determine a potent and practical prophylactic strategy for controlling this disease, the toxicity of the by-product kraft lignin and its ability to control severe YHV infection were investigated in juvenile black tiger shrimp (15.9 ± 1.2 g body weight). The median lethal dosage at 96 h (96-hrs LD 50 ) of lignin in shrimp was 297 mg/L. Lignin was further added to shrimp diets via top-dressing to assess its ability to elicit immune stimulation activity. At 14 days after feeding, shrimp fed 1, 3, 5 and 10 g of lignin/kg of diet exhibited significantly higher levels of phagocytic activity (PA) than the control group (P  0.05). Additionally, lignin supplementation at 1-10 g/kg for 14 days failed to protect experimental shrimp against YHV infection. The antiviral activity of lignin against YHV in black tiger shrimp was notable in vitro because compared to control shrimp (96.7 ± 5.8%; P by-product kraft lignin efficiently inhibits YHV infection in black tiger shrimp. This information will facilitate the development of practical methods to control yellow head disease in the marine shrimp culture industry. Copyright © 2017 Elsevier Ltd. All rights reserved.

Alcoholic Beverages Obtained from Black Mulberry

Directory of Open Access Journals (Sweden)

Jacinto Darias-Martín

2003-01-01

Full Text Available Black mulberry (Morus nigra is a fruit not known only for its nutritional qualities and its flavour, but also for its traditional use in natural medicine as it has a high content of active therapeutic compounds. However, this fruit is not widely produced in Spain but some trees are still found growing in the Canary Islands, particularly on the edges of the ravine. The inhabitants of these islands (Tenerife, La Gomera, La Palma, El Hierro and Lanzarote collect the fruit and prepare homemade beverages for medicinal purposes. Numerous authors have reported that type II diabetes mellitus can be controlled by taking a mixture containing black mulberry and water. Apart from that, this fruit has been used for the treatment of mouth, tongue and throat inflammations. In this study we present some characteristics of black mulberry juice (TSS, pH, titratable acidity, citric acid, lactic acid, polyphenols, anthocyanins, the potassium etc. and alcoholic beverages (alcoholic grade, pH, total acidity, volatile acidity, tannins, phenols etc. obtained from black mulberry. Moreover, we have studied the quality of liquors obtained from black mulberry in Canary Islands.

Utilization of spent sulfite liquor carbohydrates

Energy Technology Data Exchange (ETDEWEB)

Wiley, A J; Whitmore, L M; Boggs, Jr, L A

1959-01-01

Possible utilization of the sugars in spent sulfite liquor in the manufacture of ethanol, torula food yeast, and other fermentation products, and in the production of sugar derivatives, such as the diacetone derivatives, is discussed.

Aroma characteristics of Moutai-flavour liquor produced with Bacillus licheniformis by solid-state fermentation.

Science.gov (United States)

Zhang, R; Wu, Q; Xu, Y

2013-07-01

The potential of Bacillus licheniformis as a starter culture for aroma concentration improvement in the fermentation of Chinese Moutai-flavour liquor was elucidated. The volatile compounds produced by B. licheniformis were identified by GC-MS, in which C4 compounds, pyrazines, volatile acids, aromatic and phenolic compounds were the main ingredients. The strains B. licheniformis (MT-6 and MT-15) produced more volatile compound concentrations, mainly C4 compounds, than the type strain of B. licheniformis (ATCC 14580) at the fermentation temperature of 55°C. Meanwhile, more volatile compound concentrations were produced by B. licheniformis in solid-state fermentation than in submerged state fermentation. Thus, the strains MT-6 and MT-15 were used as the Bacillus starter culture for investigating Moutai-flavour liquor production. The distilled liquor inoculated with Bacillus starter culture was significantly different from the liquor without inoculum. This was particularly evident in the fore-run part of the distilled sample which was inoculated with Bacillus starter culture, where volatile compounds greatly increased compared to the control. Furthermore, the distilled liquor with Bacillus starter culture showed improved results in sensory appraisals. These results indicated that B. licheniformis was one of the main species influencing the aroma characteristics of Moutai-flavour liquor. This is the first report of an investigation into the effect of Bacillus starter cultures on the flavour features of Moutai-flavour liquor, which verified that Bacillus licheniformis can enhance aroma concentration in Moutai-flavour liquor. Bacillus starter culture brought C4 compounds, pyrazines, volatile acids, aromatic and phenolic compounds to the liquor, which gave a better result in sensory appraisals. © 2013 The Society for Applied Microbiology.

Computer model for economic study of unbleached kraft paperboard production

Science.gov (United States)

Peter J. Ince

1984-01-01

Unbleached kraft paperboard is produced from wood fiber in an industrial papermaking process. A highly specific and detailed model of the process is presented. The model is also presented as a working computer program. A user of the computer program will provide data on physical parameters of the process and on prices of material inputs and outputs. The program is then...

Radiotracer experiments on lignin reactions, 2

International Nuclear Information System (INIS)

Terashima, Noritsugu; Araki, Hiroshi; Suganuma, Nobuo.

1977-01-01

The behavior of the specific carbon atoms of lignin during the cooking process was studied. Pine wood meal containing the protolignin labelled with 14-C was prepared, and treated under sulfate cooking conditions. The incorporation and distribution of radioactivity were traced in three fractions separated from the black liquor according to their solubilities and molecular weights. The gamma position carbon at the end of side chain of phenylpropane unit in lignin was eliminated easily from the high molecular weight portion in considerable extent during the cooking process, and a part of the eliminated carbon condenses again with the aromatic ring. However, a large portion of the eliminated gamma-carbon was found in the low molecular fraction of water soluble part of the black liquor. The radioactivity of alpha-carbons in the side chains adjacent to aromatic rings was found to be distributed in three fractions similarly to that of beta-carbons, except that the incorporation of radioactivity of alpha-carbons was slightly low in high molecular fraction, and slightly high in low molecular water soluble fraction as compared with that of beta-carbons and aromatic ring carbons. The number of residual carbon atoms per one monomer unit in high molecular kraft lignin was calculated from the specific incorporation ratio of radioactivity. The carbon skelton was estimated and the molecular formula was given by the elementary analysis and molecular weight determination. (Iwakiri, K.)

PYROLIGNEOUS LIQUOR PRODUCED FROM ACACIA MEARNSII DE WILD WOOD UNDER CONTROLLED CONDITIONS AS A RENEWABLE SOURCE OF CHEMICALS

Directory of Open Access Journals (Sweden)

Carolina M. Furtado

2015-09-01

Full Text Available Acacia mearnsii de Wild (black wattle is one of the most important trees planted in Southern Brazil for tannin extraction and charcoal production. The pyrolysis of the black wattle wood used for obtaining charcoal is performed in brick ovens, with the gas fraction being sent directly into the environment. The present study examines the condensable compounds present in the liquor produced from black wattle wood at different thermal degradation conditions, using gas chromatography coupled with mass spectrometry (GC/MS. Branches of black wattle were thermally degraded at controlled ambient and temperature conditions. Overall, a higher variety of compounds were obtained under atmospheric air pressure than under synthetic air pressure. Most of the tentatively identified compounds, such as carboxylic acids, phenols, aldehydes, and low molecular mass lignin fragments, such as guayacol, syringol, and eugenol, were products of lignin thermoconversion. Substituted aromatic compounds, such as vanillin, ethyl vanillin, and 2-methoxy-4-propeny-phenol, were also identified. At temperatures above 200 ºC, furan, 2-acetylfuran, methyl-2-furoate, and furfural, amongst others, were identified as polysaccharide derivatives from cellulose and hemicellulose depolymerization. This study evidences the need for adequate management of the condensable by-products of charcoal production, both for economic reasons and for controlling their potential environmental impact.

77 FR 74025 - Federated Indians of Graton Rancheria-Liquor Control Statute

Science.gov (United States)

2012-12-12

... Statute reads as follows: Chapter One--Introduction Section: 1.1 Authority. This Statute is enacted... viability of tribal enterprises. 1.3 Short Title. This Statute shall be known and cited as the ``Liquor..., currently prohibits the introduction of liquor into Indian country, except in accordance with State law and...

Studies on the antimicrobial effect of corn steep liquor on some ...

African Journals Online (AJOL)

ROFIAT

2014-01-08

Jan 8, 2014 ... The antimicrobial effect of Corn Steep Liquor (CSL) was investigated over a five day period. The pH and titrable acidity of the liquor were determined, while the antimicrobial effect on some diarrhoea causing organisms such as Escherichia coli, Salmonella enteriditis, Staphylococcus aureus and Vibrio.

Reduction efficiency prediction of CENIBRA's recovery boiler by direct minimization of gibbs free energy

Directory of Open Access Journals (Sweden)

W. L. Silva

2008-09-01

Full Text Available The reduction efficiency is an important variable during the black liquor burning process in the Kraft recovery boiler. This variable value is obtained by slow experimental routines and the delay of this measure disturbs the pulp and paper industry customary control. This paper describes an optimization approach for the reduction efficiency determination in the furnace bottom of the recovery boiler based on the minimization of the Gibbs free energy. The industrial data used in this study were directly obtained from CENIBRA's data acquisition system. The resulting approach is able to predict the steady state behavior of the chemical composition of the furnace recovery boiler, - especially the reduction efficiency when different operational conditions are used. This result confirms the potential of this approach in the analysis of the daily operation of the recovery boiler.

Precipitation of uranium peroxide from the leach liquor of uranium ores

International Nuclear Information System (INIS)

Gao Xizhen; Lin Sirong; Guo Erhua; Lu Shijie

1995-06-01

A chemical precipitation process of recovering uranium from the leach liquor of uranium ores was investigated. The process primarily includes the precipitation of iron with lime, the preprocessing of the slurry of iron hydroxides and the precipitation of uranium with H 2 O 2 . The leach liquor is neutralized by lime milk to pH 3.7 to precipitate the iron hydroxides which after flocculation and settle is separated out and preprocessed at 170 degree C in an autoclave. H 2 O 2 is then used to precipitate uranium in the leach liquor free of iron, and the pH of process for uranium precipitation adjusted by adding MgO slurry to 3.5. The barren solution can be used to wash the filter cakes of leach tailing. The precipitated slurry of iron hydroxides after being preprocessed is recycled to leaching processes for recovering uranium in it. This treatment can not only avoid the filtering of the slurry of iron hydroxides, but also prevent the iron precipitate from redissolving and consequently the increase of iron concentration in the leach liquor. The results of the investigation indicate that lime, H 2 O 2 and MgO are the main chemical reagents used to obtain the uranium peroxide product containing over 65% uranium from the leach liquor, and they also do not cause environmental pollution. In accordance with the uranium content in the liquor, the consumption of chemical reagent for H 2 O 2 (30%) and MgO are 0.95 kg/kgU and 0.169 kg/kgU, respectively. (1 fig., 8 tabs., 7 refs.)

An environmental systems analysis of the Kraft pulp industry in Thailand

NARCIS (Netherlands)

Warit, J.

2006-01-01

The pulp industry inThailandis of economic and social importance because of its production value, the revenues from export and the employment in this sector. The eucalyptus-based Kraft pulp industry plays an

Bio-based polyurethane prepared from Kraft lignin and modified castor oil

Directory of Open Access Journals (Sweden)

L. B. Tavares

2016-11-01

Full Text Available Current challenges highlight the need for polymer research using renewable natural sources as a substitute for petroleum-based polymers. The use of polyols obtained from renewable sources combined with the reuse of industrial residues such as lignin is an important agent in this process. Different compositions of polyurethane-type materials were prepared by combining technical Kraft lignin (TKL with castor oil (CO or modified castor oil (MCO1 and MCO2 to increase their reactivity towards diphenylmethane diisocyanate (MDI. The results indicate that lignin increases the glass transition temperature, the crosslinking density and improves the ultimate stress especially for those prepared from MCO2 and 30% lignin content from 8.2 MPa (lignin free to 23.5 MPa. Scanning electron microscopy (SEM micrographs of rupture surface after uniaxial tensile tests show ductile-to-brittle transition. The results show the possibility to develop polyurethane-type materials, varying technical grade Kraft lignin content, which cover a wide range of mechanical properties (from large elastic/low Young modulus to brittle/high Young modulus polyurethanes.

Recovery of flavonoids from orange press liquor by an integrated membrane process.

Science.gov (United States)

Cassano, Alfredo; Conidi, Carmela; Ruby-Figueroa, René

2014-08-11

Orange press liquor is a by-product generated by the citrus processing industry containing huge amounts of natural phenolic compounds with recognized antioxidant activity. In this work, an integrated membrane process for the recovery of flavonoids from orange press liquors was investigated on a laboratory scale. The liquor was previously clarified by ultrafiltration (UF) in selected operating conditions by using hollow fiber polysulfone membranes. Then, the clarified liquor with a total soluble solids (TSS) content of 10 g·100 g-1 was pre-concentrated by nanofiltration (NF) up to 32 g TSS 100 g-1 by using a polyethersulfone spiral-wound membrane. A final concentration step, up to 47 g TSS 100 g-1, was performed by using an osmotic distillation (OD) apparatus equipped with polypropylene hollow fiber membranes. Suspended solids were completely removed in the UF step producing a clarified liquor containing most part of the flavonoids of the original press liquor due to the low rejection of the UF membrane towards these compounds. Flavanones and anthocyanins were highly rejected by the NF membrane, producing a permeate stream with a TSS content of 4.5 g·100 g-1. An increasing of both the flavanones and anthocyanins concentration was observed in the NF retentate by increasing the volume reduction factor (VRF). The final concentration of flavonoids by OD produced a concentrated solution of interest for nutraceutical and pharmaceutical applications.

Recovery of Flavonoids from Orange Press Liquor by an Integrated Membrane Process

Directory of Open Access Journals (Sweden)

Alfredo Cassano

2014-08-01

Full Text Available Orange press liquor is a by-product generated by the citrus processing industry containing huge amounts of natural phenolic compounds with recognized antioxidant activity. In this work, an integrated membrane process for the recovery of flavonoids from orange press liquors was investigated on a laboratory scale. The liquor was previously clarified by ultrafiltration (UF in selected operating conditions by using hollow fiber polysulfone membranes. Then, the clarified liquor with a total soluble solids (TSS content of 10 g·100 g−1 was pre-concentrated by nanofiltration (NF up to 32 g TSS 100 g−1 by using a polyethersulfone spiral-wound membrane. A final concentration step, up to 47 g TSS 100 g−1, was performed by using an osmotic distillation (OD apparatus equipped with polypropylene hollow fiber membranes. Suspended solids were completely removed in the UF step producing a clarified liquor containing most part of the flavonoids of the original press liquor due to the low rejection of the UF membrane towards these compounds. Flavanones and anthocyanins were highly rejected by the NF membrane, producing a permeate stream with a TSS content of 4.5 g·100 g−1. An increasing of both the flavanones and anthocyanins concentration was observed in the NF retentate by increasing the volume reduction factor (VRF. The final concentration of flavonoids by OD produced a concentrated solution of interest for nutraceutical and pharmaceutical applications.

Alkali-treated kraft lignin as a component in flakeboard eesins

Science.gov (United States)

Mon-Lin Kuo; Chung-Yun Hse; Dee-Hua Huang

1991-01-01

Southern pine kraft lignin was reacted with NaOH (15 and 20% based on dry lignin) at 170, 200, and 250°C for 30 and 60 min. Sweetgum flake boards bonded with phenolic resins containing 50% hydroxymethylated lignin prepared from some of the alkali treated lignins were compared with boards bonded with a neat PF resin. Results indicate that boards bonded with lignin-...

Efeito do teor de lignina da madeira de Eucalyptus globulus Labill. no desempenho da polpação kraft

Directory of Open Access Journals (Sweden)

Gabriel Valim Cardoso

2011-01-01

Full Text Available In this research, it was analyzed the lignin content effect of Eucalyptus globulus Labill. wood in kraft pulping optimization. Seventy-two laboratory cooking were made with wood chips obtained from six Eucalyptus globulus trees selected from a group of 50 trees. The wood chips from three trees with the lowest lignin content, with average 20.53%, were mixed proportionally based on the tree weights, obtaining the sample of low lignin content wood. The same was made to obtain the sample for wood chips with the highest lignin content, with average 23.02%. The two lignin levels were statistically different. The two wood samples had basic densities statistically not different. Using three maximum temperatures levels (160, 165 and 170ºC, and three active alkali charged (17, 18.5 and 20%, the wood chips were converted to kraft pulps. The pulps were then characterized to analyze the influence of the distinct treatments employed in the cooking on their properties. The effect of the cooking conditions was expressed by mathematical models in order to determine the optimum points for each of the evaluated properties. The optimization process indicated maximum temperature of 168ºC, and active alkali of 19%, for maximum kraft pulping yield to achieve kappa number 18; this result was for woods with low lignin content. For woods containing the high lignin content, the optimization showed maximum cooking temperature of 169ºC and active alkali of 19% for kappa number of 18. The average reduction of 2.49% in wood lignin content resulted a correspondent gain of 2.2% in the kraft yield (o.d. basis and a reduction on the active alkali charge of 1.2% (o.d. basis to achieve kappa numbers from 16 to 19, preserving pulp properties. If the option is to work with kappa number 19 instead of 16, the gain in kraft yield is approximately 2%. Therefore, when working with low lignin content wood and kappa number 19 instead of 16, a substantial gain of approximately 4.2% is

77 FR 10547 - Kickapoo Traditional Tribe of Texas-First Amended Beer and Liquor Tax Ordinance

Science.gov (United States)

2012-02-22

... Amended Beer and Liquor Tax Ordinance AGENCY: Bureau of Indian Affairs, Interior. ACTION: Notice. SUMMARY: This notice publishes the amendment to the Kickapoo Traditional Tribe of Texas' Beer and Liquor Tax... adopted this amendment to the Kickapoo Traditional Tribe of Texas' Beer and Liquor Tax Ordinance by...

Eyelid liquoric fistula secondary to orbital meningocele

Directory of Open Access Journals (Sweden)

Renato Antunes Schiave Germano

2015-02-01

Full Text Available Liquoric fistula (LF is defined as the communication of the subarachnoid space with the external environment, which main complication is the development of infection in the central nervous system. We reported the case of a patient with non-traumatic eyelid liquoric fistula secondary to orbital meningocele (congenital lesion, which main clinical manifestation was unilateral eyelid edema. Her symptoms and clinical signs appeared in adulthood, which is uncommon. The patient received surgical treatment, with complete resolution of the eyelid swelling. In conclusion, eyelid cerebrospinal fluid (CSF fistula is a rare condition but with great potential deleterious to the patient. It should be considered in the differential diagnosis of unilateral eyelid edema, and surgical treatment is almost always mandatory.

21 CFR 163.111 - Chocolate liquor.

Science.gov (United States)

2010-04-01

... CONSUMPTION CACAO PRODUCTS Requirements for Specific Standardized Cacao Products § 163.111 Chocolate liquor... ingredients. The following safe and suitable ingredients may be used: (1) Cacao fat and cocoas (breakfast cocoa, cocoa, or lowfat cocoa); (2) Alkali ingredients. Ammonium, potassium, or sodium bicarbonate...

THE PRODUCTION OF ORANGE PRESS LIQUOR SPIRIT: TECHNICAL AND ECONOMIC ASPECTS

Directory of Open Access Journals (Sweden)

J. O. FERREIRA

2008-10-01

Full Text Available

The orange juice industry produces, at the end of the residue extraction, a by-product called orange press liquor. Considering its high content of soluble solids and the large volume of the liquor produced in Brazilian orange juice plants, an earlier study was conducted on the technical viability of using orange press liquor as raw material for a new distilled beverage, with promising results. With a view to increasing efficiency and possibly attracting investments in the growing international market for new and exotic beverages, the aim of the present study was to optimize the orange press liquor spirit process and to evaluate the economic aspects of its production. The results showed that this process can yield a good quality beverage, comparable to the sugar cane spirit cachaça and other similar products, as well as having economic advantages and potential for immediate further growth, without extra investment costs.

Plastic Optical Fiber Sensing of Alcohol Concentration in Liquors

OpenAIRE

Masayuki Morisawa; Shinzo Muto

2012-01-01

A simple optical fiber sensing system of alcohol concentration in liquors has been studied. In this sensor head, a mixture polymer of novolac resin and polyvinylidenefluoride (PVDF) with a ratio of 9 : 1 was coated as a sensitive cladding layer on the plastic fiber core made of polystyrene-(PS-)coated polycarbonate (PC). Using this sensor head and a green LED light source, it was confirmed that alcohol concentration in several kinds of liquors from beer to whisky can easily be measured with a...

Engineering study: disposition of terminal liquors for interim storage. [Eight alternative processes

Energy Technology Data Exchange (ETDEWEB)

Metz, W.P.; Ogren, W.E.

1975-02-01

Eight alternative processes were chosen as being technologically feasible within the time frame dictated by budgeting procedures and terminal liquor availability. Solidified waste products acceptable for single-shell tank storage were assumed to be placed in available single-shell tanks. Double-shell tanks were used only for the more mobile terminal liquors or semi-solid mush products. The mush, chemical neutralization, and clay in-tank processes offer potential savings of tens of millions of dollars over double-shell tank storage of terminal liquors. In order to achieve this cost savings, the process development and demonstration must be completed prior to the beginning of double-shell tank construction (Dec. 1976) expected to be funded from a fiscal year 1977 line item. Budgeting for these additional double-shell tanks must proceed since the processing options discussed here are not yet available and may not prove to be available at the required time. This study indicates the following topics for additional study: Process technology development to achieve interim storage of terminal liquor products receives the greatest emphasis as a means of reducing capital expenditures. Interim storage product criteria, waste inventory, and conversion to final form require definition to allow comparison of the alternatives for disposition of terminal liquors. The pseudotechnical nature of product acceptability criteria is important to the evaluation of the partial neutralization and aluminum removal alternatives. More accurate estimates of terminal liquor quantity and composition are required to give a sound technical basis for choosing the appropriate processing alternative. Retrieval and reprocessing operations may affect the comparisons presented by this study. (DLC)

Reinforcing Natural Rubber with Cellulose Nanofibrils Extracted from Bleached Eucalyptus Kraft Pulp

Science.gov (United States)

Chunmei Zhang; Tianliang Zhai; Ronald Sabo; Craig Clemons; Yi Dan; Lih-Sheng Turng

2014-01-01

Reinforced natural rubber (NR) nanocomposites were prepared by solution mixing, casting, and evaporation of pre-vulcanized natural rubber latex and an aqueous suspension of cellulose nanofibrils (CNFs) extracted from bleached eucalyptus kraft pulp. Scanning electron microscopy (SEM) images showed that there were no micro-scaled aggregates observed in the nanocomposites...

Kraft Foods, Inc. in India — The Cadbury Acquisition

OpenAIRE

V. S. Pai; Ram Subramanian

2014-01-01

When the United States-based Kraft Foods, Inc. (KFI) acquired the United Kingdom-based Cadbury plc, KFI got entry into the Indian market. KFI CEO, Irene Rosenfeld had targeted the developing markets as key for the company to achieve a 5% organic growth rate and the strong position of Cadbury India augured well for expanding KFI's presence in that market. However, after nearly a year since the acquisition, KFI was moving slowly in India and appeared content to consolidate Cadbury's market pres...

Biochemical methane potential of kraft bleaching effluent and codigestion with other in-mill streams

DEFF Research Database (Denmark)

Fitamo, Temesgen Mathewos; Dahl, Olli; Master, Emma

2016-01-01

and in combination: total bleaching effluent, alkaline bleaching effluent, kraft evaporator condensate, and chemithermomechanical pulping effluent. The total bleaching effluent, consisting of the chlorine dioxide bleaching and alkaline bleaching effluents, exhibited the highest potential for organic matter...

Plastic Optical Fiber Sensing of Alcohol Concentration in Liquors

Directory of Open Access Journals (Sweden)

Masayuki Morisawa

2012-01-01

Full Text Available A simple optical fiber sensing system of alcohol concentration in liquors has been studied. In this sensor head, a mixture polymer of novolac resin and polyvinylidenefluoride (PVDF with a ratio of 9 : 1 was coated as a sensitive cladding layer on the plastic fiber core made of polystyrene-(PS-coated polycarbonate (PC. Using this sensor head and a green LED light source, it was confirmed that alcohol concentration in several kinds of liquors from beer to whisky can easily be measured with a fast response time less than 1 minute.

Computed tomographic volumetry of cerebral liquor by semiautomatic contour recognition and gray value histogram analysis

International Nuclear Information System (INIS)

Tschammler, A.; Middendorf, C.; Luedinghausen, M. v.; Wittenberg, G.; Krahe, T.

1996-01-01

A program (VAC, Siemens) using selfmade, anthropomorphous phantomas to measure semiautomatically the volume of the cerebral liquor in CT scans of the whole skull was tested. Cerebral tissue was simulated by ellipsoid bodies made from Agar and Nal which were placed in a human skull. Volumes of the ventricular and subarachnoidal liquor could be defined arbitrarily. A correlation coefficient of r>=0.9 using a slice thickness of 1-5 mm was found (thickness 8 mm: r=0.75). The volume of the cerebral liquor was underestimated by 25-68%. Separate measurements of the ventricular and subarachnoidal liquor spaces showed a high accuracy of the measurements done in the ventricles (r=0.997, y=0.996x-1). The volume of the subarachnoidal liquor was not detected completely due to partial volume effects which were seen especially in the basal and apical scans. The program VAC is useful for the semiautomatic measurement of the volume of the ventricles. The assessment of the subarachnoidal liquor is limited to semiquantitative results. (orig./MG) [de

Effects of ancestral populations on entrepreneurial founding and failure: private liquor stores in Alberta, 1994--2003

OpenAIRE

Glen Dowell; Robert J. David

2011-01-01

Until 1993, all liquor stores in the Canadian province of Alberta were government owned and run. In the fall of 1993, the provincial government exited liquor retailing, all government stores were shut down, and entrepreneurs were allowed to open private liquor stores. In this article, we take advantage of this abrupt regulatory change in the Alberta liquor-retailing industry to address two related issues that have received little empirical attention. First, we investigate how an ancestral pop...

Effect of Cellulases and Xylanases on Refining Process and Kraft Pulp Properties.

Directory of Open Access Journals (Sweden)

Kamila Przybysz Buzała

Full Text Available Samples of bleached kraft pine cellulosic pulp, either treated with an enzyme preparation (a Thermomyces lanuginosus xylanase, an Aspergillus sp. cellulase, and a multienzyme preparation NS-22086 containing both these activities or untreated, were refined in a laboratory PFI mill. The treatment with cellulases contained in the last two preparations significantly improved the pulp's susceptibility to refining (the target freeness value of 30°SR was achieved in a significantly shorter time, increased water retention value (WRV and fines contents while the weighted average fiber length was significantly reduced. These changes of pulp parameters caused deterioration of paper strength properties. The treatment with the xylanase, which partially hydrolyzed xylan, small amounts of which are associated with cellulose fibers, only slightly loosened the structure of fibers. These subtle changes positively affected the susceptibility of the pulp to refining (refining energy was significantly reduced and improved the static strength properties of paper. Thus, the treatment of kraft pulps with xylanases may lead to substantial savings of refining energy without negative effects on paper characteristics.

Application of thermoalkalophilic xylanase from Arthrobacter sp. MTCC 5214 in biobleaching of kraft pulp

Digital Repository Service at National Institute of Oceanography (India)

Khandeparker, R.; Bhosle, N.B.

released by enzyme treatment showed a characteristic peak at 280 nm indicating the presence of lignin in the released coloring matter. Enzymatic prebleaching of kraft pulp showed 20 % reduction in kappa number of the pulp without much change in viscosity...

Impedance study of tea with added taste compounds using conducting polymer and metal electrodes.

Science.gov (United States)

Dhiman, Mopsy; Kapur, Pawan; Ganguli, Abhijit; Singla, Madan Lal

2012-09-01

In this study the sensing capabilities of a combination of metals and conducting polymer sensing/working electrodes for tea liquor prepared by addition of different compounds using an impedance mode in frequency range 1 Hz-100 KHz at 0.1 V potential has been carried out. Classification of six different tea liquor samples made by dissolving various compounds (black tea liquor + raw milk from milkman), (black tea liquor + sweetened clove syrup), (black tea liquor + sweetened ginger syrup), (black tea liquor + sweetened cardamom syrup), (black tea liquor + sweet chocolate syrup) and (black tea liquor + vanilla flavoured milk without sugar) using six different working electrodes in a multi electrode setup has been studied using impedance and further its PCA has been carried out. Working electrodes of Platinum (Pt), Gold (Au), Silver (Ag), Glassy Carbon (GC) and conducting polymer electrodes of Polyaniline (PANI) and Polypyrrole (PPY) grown on an ITO surface potentiostatically have been deployed in a three electrode set up. The impedance response of these tea liquor samples using number of working electrodes shows a decrease in the real and imaginary impedance values presented on nyquist plots depending upon the nature of the electrode and amount of dissolved salts present in compounds added to tea liquor/solution. The different sensing surfaces allowed a high cross-selectivity in response to the same analyte. From Principal Component Analysis (PCA) plots it was possible to classify tea liquor in 3-4 classes using conducting polymer electrodes; however tea liquors were well separated from the PCA plots employing the impedance data of both conducting polymer and metal electrodes.

An acoustic technique for the determination of liquor level in tanks

International Nuclear Information System (INIS)

Watson, J.; Jones, T.L.

1980-02-01

The design, development and application of a prototype suitable for the measurement of liquor levels in tanks is described. The technique involves directing an acoustic pulse down a constraining tube to the liquor surface and measuring the time of return of the reflected pulse. Using the equipment it is possible to determine the position of a solid surface with a total error of less than 1 mm. The prototype instrument was used to measure the volume of liquors contained in rectangular slab tanks used for accountancy purposes at Dounreay Nuclear Power Development Establishment. The total error obtained in an individual measurement of volume was less than 0.2 litres (95% confidence limits). The instrument may be used as a replacement for a Pneumercator system in existing installations. (author)

27 CFR 5.46 - Standard liquor bottles.

Science.gov (United States)

2010-04-01

..., DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF DISTILLED SPIRITS Standards of Fill for... appeal procedures, see part 13 of this chapter. (Sec. 5, 49 Stat. 981, as amended (27 U.S.C. 205); 26 U.S...

Bazı çam türlerinden kraft kağıt hamuru elde etme sürecinde sodyum borhidrür ilavesinin etkileri

Directory of Open Access Journals (Sweden)

Akın SARAÇBAŞI

2016-12-01

Full Text Available Bu araştırmada, kızılçam (Pinus brutia Ten. ve Monteri çamı (Pinus radiata D. Don. türlerinden toplam verim ve delignifikasyonu geliştirmek amacı ile alternatif bir Sodyum borhidrür (NaBH4-Kraft kâğıt hamuru elde etme yöntemi üzerinde çalışılmıştır. Delignifikasyon derecesi ve hamur verimi üzerinde reaksiyon koşullarının etkileri değerlendirilmiştir.Sonuçlar, sodyum borhidrür ilavesinin bilinen Kraft yöntemine göre her iki çam türünün hem verim hem de delignifikasyonunu geliştirmek için daha etkili olduğunu göstermektedir. Sodyum borhidrür (NaBH4-Kraft yönteminin, geleneksel Kraft yönteminin tek başına verdiği kappa numarası ve yüksek verim açısından, daha hızlı ve daha seçici olduğu düşünülmektedir. Ancak, kızılçam için en iyi Sodyum borhidrür (NaBH4-Kraft kâğıt hamuru üretim koşulu Aktif Alkali: %16, Sülfidite: %28, NaBH4 oranı: %0.5 iken, Monteri çamı için en iyi Sodyum borhidrür (NaBH4-Kraft kâğıt hamuru üretim koşulunun ise Aktif Alkali: %20, Sülfidite: %26, NaBH4 Oranı: %0.7 olduğu bulunmuştur.

Application of xylanases from Amazon Forest fungal species in bleaching of eucalyptus kraft pulps

Directory of Open Access Journals (Sweden)

Roseli Garcia Medeiros

2007-03-01

Full Text Available Crude xylanase preparations from Penicillium corylophilum, Aspergillus niger and Trichoderma longibrachiatum were used to treat Eucalyptus kraft pulp, prior to chlorine dioxide and alkaline bleaching sequences. The enzyme pretreatment improved brightness and delignification of non-delignified and oxygen-bleached samples of eucalyptus kraft pulp. Xylanase preparations from T. longibrachiatum and P. corylophilum were more effective to reduce pulp kappa number. A small reduction in viscosity was obtained when the oxygen-bleached pulp was treated with xylanase preparation from A. niger. For all enzyme samples, the best release of chromophoric material from the pulp was at 237 nm. The enzyme preparation from P. corylophilum was responsible for the highest release of reducing sugar at a dosage interval of 10-20 IU/g dry weight pulp. Scanning electron microscopy studies of oxygen-bleached pulp after xylanase treatment revealed morphological changes, including holes, cracks, filament forming and peeling.Amostras de xilanases de extratos brutos de Penicillium corylophilum, Aspergillus niger e Trichoderma longibrachiatum foram utilizadas no branqueamento de polpa kraft de eucalipto antes das seqüências alcalina e dióxido de cloro. O pré-tratamento enzimático melhorou a alvura e o processo de deslignificação de amostras de polpa kraft de eucalipto não-tratada e tratada com oxigênio. Amostras de xilanases de T. longibrachiatum e P. corylophilum foram mais efetivas na redução do número kappa da polpa. A polpa tratada com oxigênio sofreu uma pequena redução na sua viscosidade quando incubada com amostra de xilanase de A. niger. Para todas as amostras de xilanases, a maior liberação de cromóforos da polpa foi a 237 nm. A amostra de xilanase de P. corylophilum liberou maior quantidade de açúcar redutor da polpa, utilizando dosagem de 10-20 UI/g de peso seco da polpa. Estudos de microscopia eletrônica de varredura revelaram várias altera

On the use of sodium lignosulphonate for enhanced oil recovery

Science.gov (United States)

Azis, M. M.; Rachmadi, H.; Wintoko, J.; Yuliansyah, A. T.; Hasokowati, W.; Purwono, S.; Rochmadi, W.; Murachman, B.

2017-05-01

There has been large interest to utilize oil reservoirs in Indonesia by using Enhanced Oil Recovery (EOR) processes. Injection of surfactant as a part of chemical injection technique in EOR is known to aid the mobility and reduction in surface tension. One potential surfactant for EOR application is Sodium Lignosulphonate (SLS) which can be made from various sources particularly empty fruit bunch of oil palm and black liquor from kraft pulp production. Here, we will discuss a number of methods for SLS production which includes lignin isolation techniques and sulphonation reaction. The use of SLS alone as EOR surfactant, however, is often not feasible as the Interfacial Tension (IFT) value of SLS is typically above the order of 10-3 dyne/cm which is mandated for EOR application. Hence, brief discussion on SLS formulation screening is provided which illustrates an extensive labwork experience during the SLS development in our lab.

19 CFR 11.6 - Distilled spirits, wines, and malt liquors in bulk.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Distilled spirits, wines, and malt liquors in bulk...; DEPARTMENT OF THE TREASURY PACKING AND STAMPING; MARKING Packing and Stamping § 11.6 Distilled spirits, wines... conveying imported distilled spirits, wines, and malt liquors, in accordance with 19 U.S.C. 467. (b) Marks...

Solution blow spun nanocomposites of poly(lactic acid)/cellulose nanocrystals from Eucalyptus kraft pulp

Science.gov (United States)

Cellulose nanocrystals (CNCs) were extracted from Eucalyptus kraft pulp by sulfuric acid hydrolysis, and esterified with maleic anhydride (CNCMA). The incorporation of sulfate ester groups on the cellulose surface resulted in higher stability of the nanoparticles in aqueous suspensions and lower the...

Mergers and acquisitions : the case of Kraft Foods and Cadbury

OpenAIRE

Ribeiro, Sara Isabel de Paula

2013-01-01

The aim of this dissertation is to focus on a determinant aspect of Corporate Finance that is Mergers and Acquisitions (M&A). This dissertation not only provides a practical analysis of main issued regarding a process of M&A, but also provides a theoretical framework about M&A. Specifically, this dissertation explores the real case of Kraft Foods - world’s second largest manufacturer and packager food products – and Cadbury - the world’s second largest confectionery firm. ...

Utilización de Eucalyptus spp. Alternativas de plantaciones uruguayas para pulpa Kraft

Directory of Open Access Journals (Sweden)

Javier Doldán

2011-05-01

Full Text Available Las plantaciones de Eucalyptus globulus han mostrado desiguales tasas de crecimiento en diferentes regiones de Uruguay. Esto ha motivado la búsqueda de otros orígenes de semilla y especies para la producción de pulpa de celulosa. Propiedades papeleras de las pulpas blanqueadas (ECF de especies alternativas llevan a intuir que podrían ser atractivas para mercados de pulpa de fibra corta. En este trabajo se realiza un comparativo del E. grandis, E. dunnii, E. maidenii y E. globulus (procedencia de semilla “Jeeralang” con el E. globulus predominante en Uruguay. Se discute el potencial de estas maderas como base para una mezcla en cocción, basándose en el análisis de propiedades físicas (densidad aparente básica, propiedades pulpables (rendimiento, carga de álcali activo en cocción Kraft y consumo de madera y propiedades papeleras. En trabajos previos se han encontrado diferencias significativas entre el comportamiento pulpable del Eucalyptus globulus y Eucalyptus maidenii, sugiriendo que nosería recomendable mezclar estas especies. La misma conclusión se podría extender a las especies de Eucalyptus estudiadas. Sin embargo, teniendo en cuenta los similares requerimientos en las cargas de álcali activo, la mezcla entre especies alternativas podría ser aplicada.AbstractEucalyptus globulus plantations have shown different growth rates in different sites in Uruguay. This fact has triggered the search for other pulp wood species and seed provenance. Paper making properties of ECF bleached pulps of alternative speciessuggest that these species could be perfectly used as hardwood bleached pulp raw materials. This study intends to compare alternativeUruguayan pulpwood species E. grandis, E. dunnii, E. maidenii and “Jeeralang” a seed provenance of E. globulus to the E. globulus most widely cultivated in the country. Physical properties of wood (Basic Density, Kraft pulping performance (pulp yield, active alkali and wood consumption

[Study on the Recognition of Liquor Age of Gujing Based on Raman Spectra and Support Vector Regression].

Science.gov (United States)

Wang, Guo-xiang; Wang, Hai-yan; Wang, Hu; Zhang, Zheng-yong; Liu, Jun

2016-03-01

It is an important and difficult research point to recognize the age of Chinese liquor rapidly and exactly in the field of liquor analyzing, which is also of great significance to the healthy development of the liquor industry and protection of the legitimate rights and interests of consumers. Spectroscopy together with the pattern recognition technology is a preferred method of achieving rapid identification of wine quality, in which the Raman Spectroscopy is promising because of its little affection of water and little or free of sample pretreatment. So, in this paper, Raman spectra and support vector regression (SVR) are used to recognize different ages and different storing time of the liquor of the same age. The innovation of this paper is mainly reflected in the following three aspects. First, the application of Raman in the area of liquor analysis is rarely reported till now. Second, the concentration of studying the recognition of wine age, while most studies focus on studying specific components of liquor and studies together with the pattern recognition method focus more on the identification of brands or different types of base wine. The third one is the application of regression analysis framework, which cannot be only used to identify different years of liquor, but also can be used to analyze different storing time, which has theoretical and practical significance to the research and quality control of liquor. Three kinds of experiments are conducted in this paper. Firstly, SVR is used to recognize different ages of 5, 8, 16 and 26 years of the Gujing Liquor; secondly, SVR is also used to classify the storing time of the 8-years liquor; thirdly, certain group of train data is deleted form the train set and put into the test set to simulate the actual situation of liquor age recognition. Results show that the SVR model has good train and predict performance in these experiments, and it has better performance than other non-liner regression method such

Kinetics and compensation effects during steam gasification of Fujian anthracite using viscose liquor as catalyst

Energy Technology Data Exchange (ETDEWEB)

Lin Ju; Zhang Ji-yu; Zhong Xue-qing [Fuzhou University, Fuzhou (China). Institute of Chemical Engineering and Technology

2009-08-15

Catalytic steam gasification kinetics of Fujian Youxi anthracite using viscose liquor as catalyst was investigated in an isothermal thermo-gravimetric analyzer under ambient pressure. Coal conversions versus reaction time with different viscose liquor concentrations (0-12% NaOH) were measured at the temperature range from 850 to 950{sup o}C. The research shows that the viscose liquor can greatly improve the gasification rate and carbon conversion. The Loading Saturation Level (LSL) of the viscose liquor within the experimental conditions was also determined. The catalytic steam gasification reaction can be well fitted by a shrinking-core model (SCM) and the reaction rate constants are obtained. The kinetic analysis indicates that the catalytic gasification exhibits a prominent compensation effect between the activation energy and the pre-exponential factor. The kinetic equation including the compensation effects for the catalytic steam gasification of Fujian Youxi anthracite using viscose liquor as catalyst is presented. 23 refs., 7 figs., 3 tabs.

Treatment of soak liquor and bioelectricity generation in dual chamber microbial fuel cell.

Science.gov (United States)

Sathishkumar, Kuppusamy; Narenkumar, Jayaraman; Selvi, Adikesavan; Murugan, Kadarkarai; Babujanarthanam, Ranganathan; Rajasekar, Aruliah

2018-02-08

The discharge of untreated soak liquor from tannery industry causes severe environmental pollution. This study is characterizing the soak liquor as a substrate in the microbial fuel cell (MFC) for remediation along with electricity generation. The dual chamber MFC was constructed and operated. Potassium permanganate was used as cathode solution and carbon felt electrode as anodic and cathodic material, respectively. The soak liquor was characterized by electrochemical studies viz., cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and polarization studies, respectively. The removal percentage of protein, lipid, and chemical oxygen demand (COD) were measured before and after treatment with MFC. The results of MFC showed a highest current density of 300 mA/cm 2 and a power density of 92 mW/m 2 . The removal of COD, protein, and lipid were noted as 96, 81, and 97% respectively during MFC process. This MFC can be used in tannery industries for treating soak liquor and simultaneous electricity generation.

Daqu - a traditional Chinese liquor fermentation starter

NARCIS (Netherlands)

Zheng, X.; Rezaei Tabrizi, M.; Nout, M.J.R.; Han, B.

2011-01-01

Chinese liquor is one of the world's oldest distilled alcoholic beverages, and it is typically obtained with the use of Daqufermentation starters. Daqu is a saccharifying and fermenting agent, having a significant impact on the flavour of the product. Daqucan be categorized according to maximum

Disturbances of the liquor circulation: differential diagnosis of the hydrocephalus by radionuclide scintigraphy, pneumoencephalography and determination of the liquor pressure

Energy Technology Data Exchange (ETDEWEB)

Fuhrmeister, U; Boerner, W [Wuerzburg Univ. (F.R. Germany). Neurologische Klinik; Wuerzburg Univ. (F.R. Germany). Nuklearmedizinische Abt.)

1976-06-01

Normal-pressure hydrocephalus (NPH) is a special case of communicating hydrocephalus with disturbed resorption of cerebrospinal fluid. Because of the therapeutic consequences, NPH must be clearly differentiated from cerebral atrophy with compensatory increase of the liquor and from hydrocephalus with well-balanced cerebrospinal fluid. NPH is indicated by: excessive pressure rise after artificial volume load on the liquor space in spinal infusion tests; in the x-ray picture, an internal hydrocephalus; an acute-angled corpus callosum, and a progressive ventricular enlargement following in the pneumoencephalography; ventricular reflux with stasis in radionuclide cisternography. In some limiting cases, the diagnosis can be facilitated by a quantitative functional study of the dynamics of the cerebrospinal fluid with the aid of radionuclides. The biological half-life of /sup 131/I albumin is doubled when the resorption of the cerebrospinal fluid is disturbed.

Disturbances of the liquor circulation: differential diagnosis of the hydrocephalus by radionuclide scintigraphy, pneumoencephalography and determination of the liquor pressure

International Nuclear Information System (INIS)

Fuhrmeister, U.; Boerner, W.; Wuerzburg Univ.

1976-01-01

Normal-pressure hydrocephalus (NPH) is a special case of communicating hydrocephalus with disturbed resorption of cerebrospinal fluid. Because of the therapeutic consequences, NPH must be clearly differentiated from cerebral atrophy with compensatory increase of the liquor and from hydrocephalus with well-balanced cerebrospinal fluid. NPH is indicated by: excessive pressure rise after artificial volume load on the liquor space in spinal infusion tests; in the X-ray picture, an internal hydrocephalus; an acute-angled corpus callosum, and a progressive ventricular enlargement following in the pneumoencephalography; ventricular reflux with stasis in radionuclide cisternography. In some limiting cases, the diagnosis can be facilitated by a quantitative functional study of the dynamics of the cerebrospinal fluid with the aid of radionuclides. The biological half-life of 131 I albumin is doubled when the resorption of the cerebrospinal fluid is disturbed. (orig.) [de

'The ones that turn up are the ones that are responsible': Key stakeholders perspectives on liquor accords.

Science.gov (United States)

Curtis, Ashlee; Miller, Peter; Droste, Nicolas; McFarlane, Emma; Martino, Florentine; Palmer, Darren

2016-05-01

Liquor accords were introduced as an intervention to reduce alcohol-related harm in and around licensed venues. There have been very few evaluations of the accords, made all the more difficult given the multitude of measures that are often implemented under their banner. This study provides perspectives on the effectiveness of the liquor accords from key stakeholders who were involved in the strategy. In-depth interviews were conducted with 97 key stakeholders as part of a larger study, of which 46 spoke about the effectiveness of liquor accords. Responses were analysed using thematic analysis. Stakeholders reported the greatest benefit of liquor accords to be their ability to improve communication. Many stakeholders recognised the need for mandatory attendance and discussed whether the accords are a waste of time of resources. Stakeholders did not generally view liquor accords as effective means of reducing alcohol-related harm. There was a lack of positive feedback about liquor accords provided by stakeholders, indicating a clear need to better understand the role of liquor accords, and what they aim to achieve. Responsive regulation theory suggests that the dual roles of communication and intervention are confused, leading to some of the inherent problems with accords. The role and aims of liquor accords need to be clearly defined. The findings suggest that separating the communication and regulatory functions from accords will lead to a clearer role for accords, and interventions and regulation might be better placed in the hands of regulators and enforcement. [Curtis A, Miller P, Droste N, McFarlane E, Martino F, Palmer D. 'The ones that turn up are the ones that are responsible': Key stakeholders perspectives on liquor accords. Drug Alcohol Rev 2016;35:273-279]. © 2016 Australasian Professional Society on Alcohol and other Drugs.

Post-Digestion Liquor Treatment in the Method Combining Chemical Precipitation with Reverse Osmosis

Directory of Open Access Journals (Sweden)

Kuglarz Mariusz

2014-12-01

Full Text Available The aim of the study was to develop an effective treatment of post-digestion liquors highly-loaded with biogenic and organic substances. The scope of the research project encompassed: mesophilic anaerobic digestion of waste activated sludge (WAS as well as the treatment of post-digestion liquors, coming from the most appropriate HRT value of 25 days, in the process of ammonium magnesium phosphate (struvite precipitation targeted at ammonia nitrogen binding and a subsequent reverse osmosis (RO process. It was established that the method combining chemical precipitation and high-pressure filtration ensures a high degree of contaminants removal allowing for a direct release of treated liquors into the natural reservoir. However, in order to decrease the residual NH4+ concentration (6.1 mg NH4+/dm3 in the purified post-digestion liquors below the level allowing for a direct release to the natural reservoir, it turned out to be necessary to apply increased molar ratio of magnesium and phosphates (Mg:NH4+: PO43-= 1.5:1:1.5.

Ion-exchange preparation of high-purity vanadium acid from industrial liquors

International Nuclear Information System (INIS)

Sajdakhmedov, U.A.; Arslanov, Sh.S.; Vulikh, A.I.

1994-01-01

The results of investigations on production of special-purity vanadium acid and vanadium oxide directly from process solutions (technical grade liquors) using ionites are presented. Potentiality of thorough purification of vanadium(5) oxide, when producing vanadium acid on the KU-2 cationite with subsequent purification on anionite, is shown. On the basis of the results obtained a principle flowsheet of ion-exchange production of high-purity vanadium(5) oxide from industrial liquors has been developed. 2 refs.; 1 fig.; 4 tabs

Study of lignin biotransformation by Aspergillus fumigatus and white-rot fungi using 14C-labeled and unlabeled kraft lignins

International Nuclear Information System (INIS)

Kadam, K.K.; Drew, S.W.

1986-01-01

The biodegradation of lignin by fungi was studied in shake flasks using 14 C-labeled kraft lignin and in a deep-tank fermentor using unlabeled kraft lignin. Among the fungi screened, A. fumigatus - isolated in our laboratories - was most potent in lignin biotransformation. Dialysis-type fermentation, designed to study possible accumulation of low MW lignin-derived products, showed no such accumulation. Recalcitrant carbohydrates like microcrystalline cellulose supported higher lignolytic activity than easily metabolized carbohydrates like cellobiose. An assay developed to distinguish between CO 2 evolved from lignin and carbohydrate substrates demonstrated no stoichiometric correlation between the metabolism of the two cosubstrates. The submerged fermentations with unlabeled liqnin are difficult to monitor since chemical assays do not give accurate and true results. Lignolytic efficiencies that allowed monitoring of such fermentations were defined. Degraded lignins were clearly superior to C. versicolor in all aspects of lignin degradation; A fumigatus brought about substantial demethoxylation and dehydroxylation, whereas C. versicolor degraded lignins closely resembled undegraded kraft lignin. There was a good agreement among the different indices of lignin degradation, namely, 14 CO evolution, OCH 3 loss, OH loss, and monomer and dimer yield after permanganate oxidation

Analysis of Illicit Liquor by Headspace Gas Chromatography-Mass Spectrometry (HS-GC-MS): A Preliminary Study.

Science.gov (United States)

Punia, Bhupinder Singh; Yadav, Praveen Kumar; Bumbrah, Gurvinder Singh; Sharma, Rakesh Mohan

2017-01-01

Illicit liquors are illegally manufactured to evade taxes and represent the majority of unrecorded liquors in developing countries. Because there are no standards, the composition of illicit liquors varies greatly from sample to sample. In the current study, we analyzed the volatile components of 27 different illicit liquors via samples collected from various locations in the northern region of India. Ethanol content varied drastically and methanol was not present in any of the samples. The components found can be categorized into different groups, namely alcohols, esters, acids, nitrogen-containing components, ketones, and aldehydes. Some components-such as 1-propanol; 1-pentanol; 1-butanol; d-limonene; phenylethyl alcohols; anethole; and decanoic, octanoic, and pentanoic acids-were frequently encountered.

Study of cupuassu liquor

OpenAIRE

Cohen, Kelly de Oliveira; Jackix, Marisa de Nazaré Hoelz

2005-01-01

O cupuaçu (Theobroma grandiflorum Schum), que é um fruto amazônico, vem conquistando a cada ano mais espaço no mercado nacional e internacional com a comercialização de sua polpa. Suas sementes, consideradas como subproduto, vem despertando interesse não só no mundo científico como pelas indústrias. Sabe-se que, a partir das sementes, pode-se obter produtos análogos aos oriundos das sementes de cacau, seguindo as mesmas etapas de processamento. Dentre esses produtos tem-se o liquor de cupuaçu...

Succinic acid production from xylose mother liquor by recombinant Escherichia coli strain.

Science.gov (United States)

Wang, Honghui; Pan, Jiachuan; Wang, Jing; Wang, Nan; Zhang, Jie; Li, Qiang; Wang, Dan; Zhou, Xiaohua

2014-11-02

Succinic acid (1,4-butanedioic acid) is identified as one of important building-block chemicals. Xylose mother liquor is an abundant industrial residue in xylitol biorefining industry. In this study, xylose mother liquor was utilized to produce succinic acid by recombinant Escherichia coli strain SD121, and the response surface methodology was used to optimize the fermentation media. The optimal conditions of succinic acid fermentation were as follows: 82.62 g L -1 total initial sugars, 42.27 g L -1 MgCO 3 and 17.84 g L -1 yeast extract. The maximum production of succinic acid was 52.09 ± 0.21 g L -1 after 84 h with a yield of 0.63 ± 0.03 g g -1 total sugar, approaching the predicted value (53.18 g L -1 ). It was 1.78-fold of the production of that obtained with the basic medium. This was the first report on succinic acid production from xylose mother liquor by recombinant E. coli strains with media optimization using response surface methodology. This work suggested that the xylose mother liquor could be an alternative substrate for the economical production of succinic acid by recombinant E. coli strains.

A contractor's approach to engineering process plant for radioactive liquor processing

International Nuclear Information System (INIS)

Braide, W.M.; Fletcher, P.D.

1982-01-01

Protection of personnel from damaging sources of radiation is the overriding consideration which influences the fundamental design of plant for processing active liquors in the Nuclear Industry. The conventional design procedures of the Chemical Plant Contractor have therefore to be modified to meet the specific technology and additional safety requirements. Ways in which the added factor of radiation influences the design philosophy for Nuclear Plant compared to conventional Chemical Plant are described. Design philosophy is demonstrated by design studies for active liquor storage and evaporation plant. (author)

Apparatus for control of mercury

Science.gov (United States)

Downs, William; Bailey, Ralph T.

2001-01-01

A method and apparatus for reducing mercury in industrial gases such as the flue gas produced by the combustion of fossil fuels such as coal adds hydrogen sulfide to the flue gas in or just before a scrubber of the industrial process which contains the wet scrubber. The method and apparatus of the present invention is applicable to installations employing either wet or dry scrubber flue gas desulfurization systems. The present invention uses kraft green liquor as a source for hydrogen sulfide and/or the injection of mineral acids into the green liquor to release vaporous hydrogen sulfide in order to form mercury sulfide solids.

Grouping eucalyptus species in kraft pulp process for cost reduction

Directory of Open Access Journals (Sweden)

Apiwan Pichayadecha

2014-12-01

Full Text Available The objective of this research is to study the level of the important factors that can decrease total cost of pulp production. First of all, experts and experienced users identify the factors that affect the total production cost by applying the principle of 4M 1E cause and effect diagram. Then the primary factors were chosen based on 80% of their significance and tested by hypothesis for two population means. It was found that at the 95% confidence level the significant factors that have effects on the total production cost are amount of Effective alkali in white liquor and Kappa number. However, the proportion of easy delignification according to Eucalyptus species is considered as a significant factor based on various studies. Box-Behnken experiment is designed with respect to 3 mentioned factors and 3 levels of each factor. The response surface method (RSM is employed to determine the non-linear relation between the total cost as the response and the proportion of easy delignification, amount of Effective alkali in white liquor and Kappa number. To minimize the total cost, the optimal values of each factor are 75% of easy delignification, 112 grams per liter of Effective alkali in white liquor and 13.5 of kappa number. Under this optimal condition, the average total cost per ton of Eucalyptus is 13,393.91 Baht which is significantly less than the total cost of 15,517.06 Baht per ton before improvement.

CO{sub 2} emission and oil use reduction through black liquor gasification and energy efficiency in pulp and paper industry

Energy Technology Data Exchange (ETDEWEB)

Joelsson, J M; Gustavsson, L [Ecotechnology and Environmental Science, Mid Sweden University, SE-831 25 Oestersund (Sweden)

2008-03-15

We examine consequences of new energy technologies in the pulp and paper industry with respect to net CO{sub 2} emissions and oil use. The entire production chain from the extraction of primary resources is included in the analysis. Stand-alone production of electricity and transportation fuel from biomass is included to balance the systems compared, so that they produce the same CO{sub 2} emission and oil use reductions. The technologies considered are black liquor gasification (BLG) with electricity and motor fuels production in chemical pulp mills and increased energy efficiency in thermomechanical pulp mills. The technologies are evaluated with respect to net CO{sub 2} emission, oil use, primary energy use, biomass use and monetary cost. We find that BLG in chemical pulp mills is favourable compared to stand-alone production of fuels and electricity from biomass. It is more efficient to implement BLG with motor fuels production and stand-alone electricity production from biomass, than to implement BLG with electricity production and stand-alone production of motor fuels. Increased energy efficiency in refining of thermomechanical pulp gives CO{sub 2} savings more efficiently than stand-alone production of electricity from biomass. Sensitivity analysis indicates that our conclusions are robust with respect to energy and biomass prices and the choice of coal or natural gas for marginal electricity. Newsprint from thermomechanical pulp would require slightly less biomass and have lower costs than paper from chemical pulp, per metric ton (t) product, when the systems are also required to render the same oil use and CO{sub 2} emission reductions. Substituting mineral fillers for 25% of the chemical pulp changes the balance in favour of the chemical pulp paper. At an oil price of 40 US$/barrel, all studied pulp and paper mill technology improvements give unchanged or reduced monetary costs also when oil use and CO{sub 2} emissions are not balanced with stand

Classification of Multiple Chinese Liquors by Means of a QCM-based E-Nose and MDS-SVM Classifier.

Science.gov (United States)

Li, Qiang; Gu, Yu; Jia, Jing

2017-01-30

Chinese liquors are internationally well-known fermentative alcoholic beverages. They have unique flavors attributable to the use of various bacteria and fungi, raw materials, and production processes. Developing a novel, rapid, and reliable method to identify multiple Chinese liquors is of positive significance. This paper presents a pattern recognition system for classifying ten brands of Chinese liquors based on multidimensional scaling (MDS) and support vector machine (SVM) algorithms in a quartz crystal microbalance (QCM)-based electronic nose (e-nose) we designed. We evaluated the comprehensive performance of the MDS-SVM classifier that predicted all ten brands of Chinese liquors individually. The prediction accuracy (98.3%) showed superior performance of the MDS-SVM classifier over the back-propagation artificial neural network (BP-ANN) classifier (93.3%) and moving average-linear discriminant analysis (MA-LDA) classifier (87.6%). The MDS-SVM classifier has reasonable reliability, good fitting and prediction (generalization) performance in classification of the Chinese liquors. Taking both application of the e-nose and validation of the MDS-SVM classifier into account, we have thus created a useful method for the classification of multiple Chinese liquors.

Classification of Multiple Chinese Liquors by Means of a QCM-based E-Nose and MDS-SVM Classifier

Directory of Open Access Journals (Sweden)

Qiang Li

2017-01-01

Full Text Available Chinese liquors are internationally well-known fermentative alcoholic beverages. They have unique flavors attributable to the use of various bacteria and fungi, raw materials, and production processes. Developing a novel, rapid, and reliable method to identify multiple Chinese liquors is of positive significance. This paper presents a pattern recognition system for classifying ten brands of Chinese liquors based on multidimensional scaling (MDS and support vector machine (SVM algorithms in a quartz crystal microbalance (QCM-based electronic nose (e-nose we designed. We evaluated the comprehensive performance of the MDS-SVM classifier that predicted all ten brands of Chinese liquors individually. The prediction accuracy (98.3% showed superior performance of the MDS-SVM classifier over the back-propagation artificial neural network (BP-ANN classifier (93.3% and moving average-linear discriminant analysis (MA-LDA classifier (87.6%. The MDS-SVM classifier has reasonable reliability, good fitting and prediction (generalization performance in classification of the Chinese liquors. Taking both application of the e-nose and validation of the MDS-SVM classifier into account, we have thus created a useful method for the classification of multiple Chinese liquors.

Exploration on trickle leaching of uranium ore by refreshed liquor of bacterial oxidation

International Nuclear Information System (INIS)

Chen Shian; Huang Xiangfu; Fan Baotuan

1995-01-01

The paper describes the adaptation of the domesticated thiobacillus ferroxidans to the trickle leaching conditions of uranium ore. When the bacterial leaching liquor through multiple cycles of oxidation and regeneration was used to return to the trickle leaching, the following results were obtained: the extraction rate was more than 95%, the acid consumption was saved by 30%, and the consumed 2.0% pyrolusite (MnO 2 40%) was eliminated. The following problems are discussed: the basic principle, process and some factors influencing the process of the trickle leaching of uranium ore using regenerated liquor of bacterial oxidation, counter-current trickle leaching mode, oxidation and regeneration techniques of bacterial leaching liquor and other technological problems on the process of uranium extraction by thiobacillus ferroxidans

The impact of kappa number composition on eucalyptus kraft pulp bleachability

Directory of Open Access Journals (Sweden)

M. M. Costa

2007-03-01

Full Text Available Consumption of chemicals during ECF bleaching of kraft pulp correlates reasonably well with kappa number, which measures with KMnO4 the total amount of oxidizable material in the pulp. However, the method does not distinguish between the oxidizable material in residual lignin and other structures susceptible to oxidation, such as hexenuronic acids (HexAs, extractives and carbonyl groups in the pulp. In this study an attempt is made to separate the main contributors to the kappa number in oxygen - delignified eucalyptus Kraft pulps and evaluate how these fractions behave during ECF bleaching using chlorine dioxide as the sole oxidant (DEDD sequence. Residual lignin and HexAs proved to be the main fractions contributing to the kappa number and chlorine dioxide consumption in ECF bleaching. Pulp bleachability with chlorine dioxide increases with increasing HexAs content of the pulp but chlorine dioxide per se does not react with HexAs. Reduction of pulp with sodium borohydride under conditions for removing carbonyl groups has no impact on bleachability. No correlation was found between the pulp of the extractive content and pulp bleachability. The removal of HexAs prior to ECF bleaching significantly decreases the formation of chlorinated organics in the pulp (OX and filtrates (AOX as well as of oxalic acids in the filtrates.

A contractors's approach to engineering process plant for radioactive liquor processing

International Nuclear Information System (INIS)

Braide, W.M.; Fletcher, P.D.

1982-01-01

Protection of personnel from damaging sources of radiation is the overriding consideration which influences the fundamental design of plant for processing active liquors in the Nuclear Industry. The conventional design procedures of the Chemical Plant Contractor have therefore to be modified to meet the specific technology and additional safety requirements. This paper describes ways in which the added factor of radiation influences the design philosophy for Nuclear Plant compared to conventional Chemical Plant. The design philosophy is demonstrated by design studies for active liquor storage and evaporation plant. (author)

Metatranscriptomics Reveals the Functions and Enzyme Profiles of the Microbial Community in Chinese Nong-Flavor Liquor Starter

Directory of Open Access Journals (Sweden)

Yuhong Huang

2017-09-01

Full Text Available Chinese liquor is one of the world's best-known distilled spirits and is the largest spirit category by sales. The unique and traditional solid-state fermentation technology used to produce Chinese liquor has been in continuous use for several thousand years. The diverse and dynamic microbial community in a liquor starter is the main contributor to liquor brewing. However, little is known about the ecological distribution and functional importance of these community members. In this study, metatranscriptomics was used to comprehensively explore the active microbial community members and key transcripts with significant functions in the liquor starter production process. Fungi were found to be the most abundant and active community members. A total of 932 carbohydrate-active enzymes, including highly expressed auxiliary activity family 9 and 10 proteins, were identified at 62°C under aerobic conditions. Some potential thermostable enzymes were identified at 50, 62, and 25°C (mature stage. Increased content and overexpressed key enzymes involved in glycolysis and starch, pyruvate and ethanol metabolism were detected at 50 and 62°C. The key enzymes of the citrate cycle were up-regulated at 62°C, and their abundant derivatives are crucial for flavor generation. Here, the metabolism and functional enzymes of the active microbial communities in NF liquor starter were studied, which could pave the way to initiate improvements in liquor quality and to discover microbes that produce novel enzymes or high-value added products.

Avaliação da madeira e da polpação kraft em clones de eucaliptos Wood evaluation and Kraft pulping in eucalypts clones

Directory of Open Access Journals (Sweden)

Adriana de Fátima Gomes Gouvêa

2009-12-01

Full Text Available A produção de celulose de baixo custo e alta qualidade requer madeira adequada e bem selecionada. A seleção de clones superiores tem sido realizada com base em critérios como densidade básica, rendimento gravimétrico da polpação e composição química da madeira, especialmente de celulose, hemiceluloses, extrativos e ligninas. O objetivo deste trabalho foi avaliar as características da madeira de Eucalyptus, por método destrutivo, e a produção de polpa celulósica kraft em seis clones. Utilizaram-se cinco árvores de cada clone, aos 3 anos de idade, plantadas em espaçamento 3,0 m x 3,3 m, nas regiões de Cocais, Guanhães, Rio Doce e Santa Bárbara, Estado de Minas Gerais. A densidade básica foi medida em discos extraídos a 1,3 m de altura do solo (DAP e em cavacos da árvore inteira (amostra composta. A composição química foi medida em amostras de serragem, retiradas no DAP. Os cozimentos foram efetuados a partir de cavacos da árvore inteira. Verificou-se que a densidade medida no DAP foi ligeiramente superior à medida nos cavacos da árvore toda. A composição química geral da madeira foi muito influenciada pelo tipo de clone, local de plantio e interação. Locais mais montanhosos produziram madeira com maior teor de celulose e menor de hemicelulose. A madeira do clone F da região de Santa Bárbara e Cocais apresentaram madeiras de qualidade inferior para produção de polpa celulósica. Os melhores rendimentos de polpação kraft foram alcançados com o clone B nas regiões de Guanhães e Santa Bárbara.Low cost and high quality cellulose production demands appropriate wood. The selection of superior clones has been done based on some criteria as basic density, gravimetric yield of pulping and wood chemical composition, especially of cellulose, hemicelluloses, extractive and lignin contents. This study aimed at evaluating the characteristics of the Eucalyptus wood, by destructive methods, and the Kraft pulping

Ecotoxicological studies with newly hatched larvae of Concholepas concholepas (Mollusca, Gastropoda): bioassay with secondary-treated kraft pulp mill effluents.

Science.gov (United States)

Manríquez, Patricio H; Llanos-Rivera, Alejandra; Galaz, Sylvana; Camaño, Andrés

2013-12-01

The Chilean abalone or "loco" (Concholepas concholepas, Bruguière 1789) represent the most economically important marine recourse exploited from inner inshore Management and Exploitation Areas for Benthic Resources along the Chilean coast. In this study, newly-hatched larvae of C. concholepas were investigated as a potential model species for marine ecotoxicological studies. The study developed a behavioral standard protocol for assessing the impact that kraft pulp mill effluents after secondary treatment have on C. concholepas larvae. Under controlled laboratory conditions, newly-hatched larvae were exposed to a series of different concentrations of kraft pulp mill effluents with secondary treatment (Pinus spp. and Eucalyptus spp.), potassium dichromate as standard reference toxicant and effluent-free control conditions. Regardless of the type of effluent the results indicated that diluted kraft pulp effluent with secondary treatment had reduced effect on larval survival. Low larval survivals were only recorded when they were exposed to high concentrations of the reference toxicant. This suggests that C. concholepas larval bioassay is a simple method for monitoring the effects of kraft pulp mill effluents with secondary treatment discharged into the sea. The results indicated that dilution of ca. 1% of the effluent with an elemental chlorine free (ECF) secondary treatment is appropriate for achieving low larval mortalities, such as those obtained under control conditions with filtered seawater, and to minimize their impact on early ontogenetic stages of marine invertebrates such as newly-hatched larvae of C. concholepas. The methodological aspects of toxicological testing and behavioral responses described here with newly-hatched larvae of C. concholepas can be used to evaluate in the future the potential effects of other stressful conditions as other pollutants or changes in seawater pH associated with ocean acidification. © 2013 Elsevier Inc. All rights

Evaluating the Intoxicating Degree of Liquor Products with Combinations of Fusel Alcohols, Acids, and Esters.

Science.gov (United States)

Xie, Jia; Tian, Xiao-Fei; He, Song-Gui; Wei, Yun-Lu; Peng, Bin; Wu, Zhen-Qiang

2018-05-23

To investigate the effects of fusel alcohols on the intoxicating degree of liquor products, formulated liquors (FLs) were prepared by blending 1-propanol, isobutanol, and isoamyl alcohol with ethanol, organic acids, and corresponding ethyl esters to simulate the formula of traditional Chinese liquors. The prepared FLs were submitted for evaluation of their intoxicating degree (ID). The results showed that the fusel alcohols had a biphasic effect on the IDs of the FLs, depending on the comprehensive coordination of the characteristic minor components. The importance of the suitable ratio of alcohols/acids/esters (RAAE) on the IDs was also revealed. Under an optimal ratio level, the fusel alcohols exhibited negligible effects on the IDs of the FLs. Moreover, the ratio of isoamyl alcohol to isobutanol (IA/IB) showed a strong positive correlation to the IDs of the FLs. This study lays a foundation for the potential application in producing low-ID liquor.

IN VITRO ANDROGENIC ACTIVITY OF KRAFT MILL EFFLUENT IS ASSOCIATED WITH MASCULINIZATION OF FEMALE FISH

Science.gov (United States)

In Vitro Androgenic Activity of Kraft Mill Effluent is Associated with Masculinization of Female Fish. Lambright, CS 1 , Parks, LG 1, Orlando, E 2, Guillette, LJ, Jr.2, Ankley, G 3, Gray, LE, Jr.1 , 1USEPA, NHEERL, RTP, NC, 2 University of Florida, Dept. of Zoology, Gainesville ...

Toxicity to rainbow trout of spent still liquors from the distillation of coal

Energy Technology Data Exchange (ETDEWEB)

Herbert, D W.M.

1962-01-01

From a survey of the literature on the toxicity of ammonium salts, phenol, cyanide, and sulphide to rainbow trout, and from determinations of the toxicity of sodium thiocyanate and sodium thiosulphate, it is postulated that the toxicity of spent still liquors from the distillation of coal should be due mainly to their content of ammonia and monohydric phenols. This is confirmed by experiments showing that the toxicity of an equivalent mixture of ammonium chloride and phenol is nearly as great as that of a spent liquor from a gas works, and that phenol is almost as toxic as mixtures of the monohydric phenols known to be present in such liquors. Experiments on the effect of pH value, hardness, dissolved-oxygen concentration and temperature on the threshold concentration of monohydric phenols are described and compared with similar data for ammonia. Experiments with ammonia and phenols suggest that a mixture of these substances is at its threshold concentration when AS/AT/+PS/PT=I,AS and PS being the concentrations of un-ionized ammonia and monohydric phenols in solution and AT and PT being the threshold concentrations of these substances when tested individually in the same dilution water. A method based on these experiments for predicting the toxicity of ammonia-phenol mixtures from the chemical composition of their solutions is described, and evaluated against laboratory determinations of the toxicity of spent liquors from a coke oven, and against the death or survival of trout held captive in a stream polluted with spent liquor from a gas works. It is concluded that the correspondence between the predicted and observed toxicities is good enough for the method to be used as a basis for assessing whether trout could live in a stream to which a particular spent still liquor was discharged, or when deciding what treatment the effluent should receive to make it safe for such fish after discharge.

Process parameters affecting the delignification of eucalyptus kraft pulp with peroxyacetic acid

Directory of Open Access Journals (Sweden)

Chandranupap, P.

2004-11-01

Full Text Available Various process parameters affecting eucalyptus kraft pulp delignification with peroxyacetic acid were investigated. The results showed that pH was an important factor. The delignification rate increased with increasing pH to the value of 6. High delignification rate was obtained when the pulp was chelated with Na4-EDTA prior to the peroxyacetic acid stage. Therefore, delignification reaction rate depends on peroxyacid charge, temperature, pH and metal content of pulp.

ROLE OF TRANSCERVICAL AMNIOINFUSION IN LABOUR COMPLICATED WITH THICK MECONIUM STAINED LIQUOR

Directory of Open Access Journals (Sweden)

Anuragamayi

2015-10-01

Full Text Available OBJECTIVE: This is to evaluate the effectiveness of amnio infusion in cases of thick and particulate meconium stained liquor to reduce the incidence of fetal distress and meconium aspiration syndrome in neonates and compare neonatal outcome with control group . METHODS: A prospective comparative case control study was conducted in the Department of Obstetrics and gynecology, Government General Hospital, Kakinada. A total of 100 cases of labour complicated with thick meconium stained liquor were studied of which in 50 cases Transcervical Amnioinfusion was given and remaining 50 cases without amnioinfusion were taken as controls. The statistical analysis of neonatal outcome was done by Chi square test analysis of variance and paired t test. Liquor to reduce the incidence of fetal distress and meconium aspiration syndrome in neonates and compare neonatal. RESULTS: Operative interventions for fetal distress were significantly less in infusion group (p7 were observed in more cases of infusion group with significant difference in control group. Use of resuscitative measures for neonates were relatively more in control group with higher incidence of meconium at and below vocal cords (p <0.01. In amnioinfusion group, admissions in NICU were less (p <0.01 CONCLUSION : Transcervical amnioinfusion during labour is a safe, simple, inexpensive and effective procedure in improving the obstetric and perinatal outcome in patients labouring with thick meconium stained liquor

Evaluating the Intoxicating Degree of Liquor Products with Combinations of Fusel Alcohols, Acids, and Esters

Directory of Open Access Journals (Sweden)

Jia Xie

2018-05-01

Full Text Available To investigate the effects of fusel alcohols on the intoxicating degree of liquor products, formulated liquors (FLs were prepared by blending 1-propanol, isobutanol, and isoamyl alcohol with ethanol, organic acids, and corresponding ethyl esters to simulate the formula of traditional Chinese liquors. The prepared FLs were submitted for evaluation of their intoxicating degree (ID. The results showed that the fusel alcohols had a biphasic effect on the IDs of the FLs, depending on the comprehensive coordination of the characteristic minor components. The importance of the suitable ratio of alcohols/acids/esters (RAAE on the IDs was also revealed. Under an optimal ratio level, the fusel alcohols exhibited negligible effects on the IDs of the FLs. Moreover, the ratio of isoamyl alcohol to isobutanol (IA/IB showed a strong positive correlation to the IDs of the FLs. This study lays a foundation for the potential application in producing low-ID liquor.

Increasing polyhydroxyalkanoate (PHA) yields from Cupriavidus necator by using filtered digestate liquors.

Science.gov (United States)

Passanha, Pearl; Esteves, Sandra R; Kedia, Gopal; Dinsdale, Richard M; Guwy, Alan J

2013-11-01

The production of polyhydroxyalkanoates (PHAs) using digestate liquor as culture media is a novel application to extend the existing uses of digestates. In this study, two micro-filtered digestates (0.22 μm) were evaluated as a source of complex culture media for the production of PHA by Cupriavidus necator as compared to a conventional media. Culture media using a mixture of micro-filtered liquors from food waste and from wheat feed digesters showed a maximum PHA accumulation of 12.29 g/l PHA, with 90% cell dry weight and a yield of 0.48 g PHA/g VFA consumed, the highest reported to date for C. necator studies. From the analysis of the starting and residual media, it was concluded that ammonia, potassium, magnesium, sulfate and phosphate provided in the digestate liquors were vital for the initial growth of C. necator whereas copper, iron and nickel may have played a significant role in PHA accumulation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Design of a portable electronic nose for real-fake detection of liquors

Science.gov (United States)

Qi, Pei-Feng; Zeng, Ming; Li, Zhi-Hua; Sun, Biao; Meng, Qing-Hao

2017-09-01

Portability is a major issue that influences the practical application of electronic noses (e-noses). For liquors detection, an e-nose must preprocess the liquid samples (e.g., using evaporation and thermal desorption), which makes the portable design even more difficult. To realize convenient and rapid detection of liquors, we designed a portable e-nose platform that consists of hardware and software systems. The hardware system contains an evaporation/sampling module, a reaction module, a control/data acquisition and analysis module, and a power module. The software system provides a user-friendly interface and can achieve automatic sampling and data processing. This e-nose platform has been applied to the real-fake recognition of Chinese liquors. Through parameter optimization of a one-class support vector machine classifier, the error rate of the negative samples is greatly reduced, and the overall recognition accuracy is improved. The results validated the feasibility of the designed portable e-nose platform.

Atmospheric emission of nitrogen oxide from kraft recovery boilers in Sweden

International Nuclear Information System (INIS)

Kjoerk, Anders; Herstad Swaerd, Solvie

2000-05-01

Recovery boiler NO x emissions are low compared with those from power boilers. However tighter environmental requirements to decrease the acidic emissions implies that all sources have to be addressed. There are an ongoing evaluation and development of NO x control technologies in the pulp industry. Basically air staging, selective catalytic reduction, SCR, and selective noncatalytic reduction, SNCR, have been discussed. Other NO x control options may be available as a result of ongoing research and development. As a background in the work to reduce the acid rain it has been considered necessary to have a good picture of the NO x emission from recovery boilers, and the Thermal Engineering Research Institute in Sweden have therefore sponsored this study. The intention is to give a good general view and try to explain the reasons for the large differences between boilers. Data from the 30 kraft recovery boilers which were in operation in Sweden during 1999 have been collected. Both NO x levels and specific conditions which could have an influence on the level have been included. The evaluation show a clear correlation between the nitrogen content in the liquor and the NO x level. It seams also that a long retention time in the furnace give an opportunity to reduce the amount of nitrogen oxide. For most boilers in Sweden the NO x levels are reported in mg/MJ and comparison could be done between different types of boilers. However for recovery boilers there could be a large uncertainty in the calculation which gives the amount (mg) of NO x , the definition of the heat input to be used (MJ) is either not clear. As a base for the study the measured concentration in ppm is used instead. The reported values are in the range of 30 - 100 ppm, however the majority of the boilers operate in a more narrow range 60-80 ppm. Air staging and other combustion methods could not reasonably reduce the NO x emission with more than 20% in the next decade. If the goal is higher other

76 FR 77549 - Colorado River Indian Tribes-Amendment to Health & Safety Code, Article 2. Liquor

Science.gov (United States)

2011-12-13

... Health & Safety Code, Article 2. Liquor AGENCY: Bureau of Indian Affairs, Interior. ACTION: Notice. SUMMARY: This notice publishes the amendment to the Colorado River Tribal Health and Safety Code, Article... Code, Article 2, Liquor by Ordinance No. 10-03 on December 13, 2010. This notice is published in...

Chemical characteristics and Kraft pulping of tension wood from Eucalyptus globulus labill Características químicas e polpação Kraft de madeira de tração de Eucalyptus globulus labill

Directory of Open Access Journals (Sweden)

María Graciela Aguayo

2012-12-01

Full Text Available Tension (TW and opposite wood (OW of Eucalyptus globulus trees were analyzed for its chemical characteristics and Kraft pulp production. Lignin content was 16% lower and contained 32% more syringyl units in TW than in OW. The increase in syringyl units favoured the formation of β-O-4 bonds that was also higher in TW than in OW (84% vs. 64%, respectively. The effect of these wood features was evaluated in the production of Kraft pulps from both types of wood. At kappa number 16, Kraft pulps obtained from TW demanded less active alkali in delignification and presented slightly higher or similar pulp yield than pulps made with OW. Fiber length, coarseness and intrinsic viscosity were also higher in tension than in opposite pulps. When pulps where refined to 30°SR, TW pulps needed 18% more revolutions in the PFI mill to achieve the same beating degree than OW pulps. Strength properties (tensile, tear and burst indexes were slightly higher or similar in tension as compared with opposite wood pulps. After an OD0(EOD1 bleaching sequence, both pulps achieved up to 89% ISO brightness. Bleached pulps from TW presented higher viscosity and low amount of hexenuronic acids than pulps from OW. Results showed that TW presented high xylans and low lignin content that caused a decrease in alkali consumption, increase pulp strength properties and similar bleaching performance as compared with pulps from OW.Madeira de tração e oposta de árvores de Eucalyptus globulus foram analisadas quanto a suas características químicas e produção de polpa Kraft. A caracterização química da madeira de tração (TW de Eucalyptus globulus Labill. mostrou um conteúdo similar de celulose, alto conteúdo de xilanas e baixo conteúdo de lignina quando comparada com a madeira oposta (OW de uma mesma árvore. O conteúdo de lignina foi 16% menor e contém 32% mais unidades siringila em TW que em OW. O aumento das unidades siringila favoreceu a formação de ligações �

Effects of Chinese Liquors on Cardiovascular Disease Risk Factors in Healthy Young Humans

Directory of Open Access Journals (Sweden)

Ju-Sheng Zheng

2012-01-01

Full Text Available Objectives. To elucidate whether consumption of two Chinese liquors, tea-flavor liquor (TFL and traditional Chinese liquor (TCL have protective effects on cardiovascular disease (CVD risk factors in healthy human subjects. Methods. Forty-five healthy subjects (23 men, 22 women, aged 23–28, were recruited and randomized into two groups: TFL and TCL, and consumed 30 mL/day (45% (v/v alcohol of either liquor for 28 days. Results. Serum high-density lipoprotein cholesterol/low-density lipoprotein cholesterol (HDL-C/LDL-C and apolipoprotein A1 were significantly increased, and total cholesterol (TC and TC/HDL-C were significantly decreased after the intervention in both groups (P<0.05. Serum uric acid (P=0.004 for TFL, P=0.001 for TCL, glucose (P<0.001 for TFL, P<0.001 for TCL and endothelial adhesion molecules (P<0.05 were significantly decreased after the intervention. ADP-induced whole blood platelet aggregation was also significantly decreased after the intervention in both TFL and TCL groups (P<0.05. Conclusions. TFL and TCL consumption had protective effects on CVD risk factors in young humans. However, the results were valid only for 28 days, and that the possibility of adverse effect (liver, kidney of chronic alcohol consumption should be considered.

27 CFR 31.52 - Wholesale dealers in liquors consummating sales of wines or beer at premises of other dealers.

Science.gov (United States)

2010-04-01

... liquors consummating sales of wines or beer at premises of other dealers. 31.52 Section 31.52 Alcohol... § 31.52 Wholesale dealers in liquors consummating sales of wines or beer at premises of other dealers... wholesale dealer on account of those sales. (b) Sales of beer. Any wholesale dealer in liquors who has...

Method for improving separation of carbohydrates from wood pulping and wood or biomass hydrolysis liquors

Science.gov (United States)

Griffith, William Louis; Compere, Alicia Lucille; Leitten, Jr., Carl Frederick

2010-04-20

A method for separating carbohydrates from pulping liquors includes the steps of providing a wood pulping or wood or biomass hydrolysis pulping liquor having lignin therein, and mixing the liquor with an acid or a gas which forms an acid upon contact with water to initiate precipitation of carbohydrate to begin formation of a precipitate. During precipitation, at least one long chain carboxylated carbohydrate and at least one cationic polymer, such as a polyamine or polyimine are added, wherein the precipitate aggregates into larger precipitate structures. Carbohydrate gel precipitates are then selectively removed from the larger precipitate structures. The method process yields both a carbohydrate precipitate and a high purity lignin.

Investigating the Variation of Volatile Compound Composition in Maotai-Flavoured Liquor During Its Multiple Fermentation Steps Using Statistical Methods

Directory of Open Access Journals (Sweden)

Zheng-Yun Wu

2016-01-01

Full Text Available The use of multiple fermentations is one of the most specific characteristics of Maotai-flavoured liquor production. In this research, the variation of volatile composition of Maotai-flavoured liquor during its multiple fermentations is investigated using statistical approaches. Cluster analysis shows that the obtained samples are grouped mainly according to the fermentation steps rather than the distillery they originate from, and the samples from the first two fermentation steps show the greatest difference, suggesting that multiple fermentation and distillation steps result in the end in similar volatile composition of the liquor. Back-propagation neural network (BNN models were developed that satisfactorily predict the number of fermentation steps and the organoleptic evaluation scores of liquor samples from their volatile compositions. Mean impact value (MIV analysis shows that ethyl lactate, furfural and some high-boiling-point acids play important roles, while pyrazine contributes much less to the improvement of the flavour and taste of Maotai-flavoured liquor during its production. This study contributes to further understanding of the mechanisms of Maotai-flavoured liquor production.

Process integration study of a kraft pulp mill converted to an ethanol production plant – part B: Techno-economic analysis

International Nuclear Information System (INIS)

Fornell, Rickard; Berntsson, Thore; Åsblad, Anders

2012-01-01

In a previous study by the authors, energy efficiency measures in a conceptual kraft pulp mill converted to a lignocellulosic ethanol plant were investigated. The results suggested a number of different process designs which would give a substantial improvement in steam economy in the ethanol plant, compared to the original design. In the present study the different process designs are evaluated from an economic point-of-view, in order to determine if energy efficiency measures and increasing by-product sales decrease the production cost of ethanol from this specific process, or if the increased costs related to the implementation of these measures overshadow the benefits from increased by-product sales. The different energy efficiency measures are compared with less capital demanding alternatives (i.e. including low or no energy efficiency improvements) in order to assess the economic benefits of different strategies when converting a kraft pulp mill to ethanol production. The study indicates the economic importance of considering energy efficiency measures when repurposing a kraft pulp mill to an ethanol plant. It is also shown that, within the context of this study, a larger investment in measures will give better economic results than less capital demanding alternatives (with less improvement in energy efficiency). From an economic and energy efficiency viewpoint many of the suggested process designs will give approximately similar results, therefore the process design should be made based on other criteria (e.g. low complexity, low maintenance). - Highlights: ► Conversion of a kraft pulp mill to ethanol production. ► Heat integration of distillation/evaporation in a lignocellulosic ethanol plant. ► Energy efficiency measures lead to lower ethanol production cost. ► If capital costs and raw material prices are low the production cost could be as low as 365 €/m 3 EtOH.

Conversion of kraft lignin over hierarchical MFI zeolite.

Science.gov (United States)

Kim, Seong-Soo; Lee, Hyung Won; Ryoo, Ryong; Kim, Wookdong; Park, Sung Hoon; Jeon, Jong-Ki; Park, Young-Kwon

2014-03-01

Catalytic pyrolysis of kraft lignin was carried out using pyrolysis gas chromatography/mass spectrometry. Hierarchical mesoporous MFI was used as the catalyst and another mesoporous material Al-SBA-15 was also used for comparison. The characteristics of mesoporous MFI were analyzed by X-ray diffraction patterns, N2 adsorption-desorption isotherms, and temperature programmed desorption of NH3. Two catalyst/lignin mass ratios were tested: 5/1 and 10/1. Aromatics and alkyl phenolics were the main products of the catalytic pyrolysis of lignin over mesoporous MFI. In particular, the yields of mono-aromatics such as benzene, toluene, ethylbenzene, and xylene were increased substantially by catalytic upgrading. Increase in the catalyst dose enhanced the production of aromatics further, which is attributed to decarboxylation, decarbonlyation, and aromatization reactions occurring over the acid sites of mesoporous MFI.

Experimental evaluation of the performances of cellulosic pads made out of Kraft and NSSC corrugated papers as evaporative media

International Nuclear Information System (INIS)

Barzegar, Mahsa; Layeghi, Mohammad; Ebrahimi, Ghanbar; Hamzeh, Yahya; Khorasani, Manouchehr

2012-01-01

Highlights: ► We experimentally evaluated the performances of cellulosic pads. ► A number of experiments have been done in a wind tunnel. ► The results showed that cooling efficiency improves with decrease of air velocity and flute size. ► Water consumption increases with the increase of air velocity. ► Cooling efficiency of various pads was also compared. - Abstract: The purpose of this study was to evaluate the performances of cellulosic pads made out of Kraft and NSSC corrugated papers in three flute sizes, experimentally. A number of experiments have been done in a wind tunnel in order to evaluate the cooling efficiency and water consumption as a function of air velocity. The tests were carried out at three levels of air velocity (1.8, 2.25, and 2.67 ms −1 ) for three flute sizes of Kraft and NSSC corrugated papers (2.5, 3.5, and 4.5 mm). Analysis of the results indicated that cooling efficiency improves with decrease of air velocity and flute size of corrugated papers; however, water consumption increases with the increase of air velocity. The results were compared with each other and it was shown that the cellulosic pad made out of Kraft paper with 2.5 mm flute size has the highest performance (92%) at 1.8 ms −1 air velocity in comparison with the other cellulosic pads.

Experimental Studies on the Hydrotreatment of Kraft Lignin to Aromatics and Alkylphenolics Using Economically Viable Fe-Based Catalysts

Science.gov (United States)

2017-01-01

Limonite, a low-cost iron ore, was investigated as a potential hydrotreatment catalyst for kraft lignin without the use of an external solvent (batch reactor, initial H2 pressure of 100 bar, 4 h). The best results were obtained at 450 °C resulting in 34 wt % of liquefied kraft lignin (lignin oil) on lignin intake. The composition of the lignin oil was determined in detail (elemental composition, GC-MS, GC×GC-FID, and GPC). The total GC-detectable monomeric species amounts up to 31 wt % on lignin intake, indicating that 92 wt % of the products in the lignin oil are volatile and thus of low molecular weight. The lignin oil was rich in low-molecular-weight alkylphenolics (17 wt % on lignin) and aromatics (8 wt % on lignin). Performance of the limonite catalyst was compared to other Fe-based catalysts (goethite and iron disulfide) and limonite was shown to give the highest yields of alkylphenolics and aromatics. The limonite catalyst before and after reaction was characterized using XRD, TEM, and nitrogen physisorption to determine changes in structure during reaction. Catalyst recycling tests were performed and show that the catalyst is active after reuse, despite the fact that the morphology changed and that the surface area of the catalyst particles was decreased. Our results clearly reveal that cheap limonite catalysts have the potential to be used for the depolymerization/hydrodeoxygenation of kraft lignin for the production of valuable biobased phenolics and aromatics. PMID:28413733

Kinetics of Strong Acid Hydrolysis of a Bleached Kraft Pulp for Producing Cellulose Nanocrystals (CNCs)

Science.gov (United States)

Qianqian Wang; Xuebing Zhao; J.Y. Zhu

2014-01-01

Cellulose nanocrytals (CNCs) are predominantly produced using the traditional strong acid hydrolysis process. In most reported studies, the typical CNC yield is low (approximately 30%) despite process optimization. This study investigated the hydrolysis of a bleached kraft eucalyptus pulp using sulfuric acid between 50 and 64 wt % at temperatures of 35−80 °C...

Xylitol production from xylose mother liquor: a novel strategy that combines the use of recombinant Bacillus subtilis and Candida maltosa

Science.gov (United States)

2011-01-01

Background Xylose mother liquor has high concentrations of xylose (35%-40%) as well as other sugars such as L-arabinose (10%-15%), galactose (8%-10%), glucose (8%-10%), and other minor sugars. Due to the complexity of this mother liquor, further isolation of xylose by simple method is not possible. In China, more than 50,000 metric tons of xylose mother liquor was produced in 2009, and the management of sugars like xylose that present in the low-cost liquor is a problem. Results We designed a novel strategy in which Bacillus subtilis and Candida maltosa were combined and used to convert xylose in this mother liquor to xylitol, a product of higher value. First, the xylose mother liquor was detoxified with the yeast C. maltosa to remove furfural and 5-hydromethylfurfural (HMF), which are inhibitors of B. subtilis growth. The glucose present in the mother liquor was also depleted by this yeast, which was an added advantage because glucose causes carbon catabolite repression in B. subtilis. This detoxification treatment resulted in an inhibitor-free mother liquor, and the C. maltosa cells could be reused as biocatalysts at a later stage to reduce xylose to xylitol. In the second step, a recombinant B. subtilis strain with a disrupted xylose isomerase gene was constructed. The detoxified xylose mother liquor was used as the medium for recombinant B. subtilis cultivation, and this led to L-arabinose depletion and xylose enrichment of the medium. In the third step, the xylose was further reduced to xylitol by C. maltosa cells, and crystallized xylitol was obtained from this yeast transformation medium. C. maltosa transformation of the xylose-enriched medium resulted in xylitol with 4.25 g L-1·h-1 volumetric productivity and 0.85 g xylitol/g xylose specific productivity. Conclusion In this study, we developed a biological method for the purification of xylose from xylose mother liquor and subsequent preparation of xylitol by C. maltosa-mediated biohydrogenation of xylose

Xylitol production from xylose mother liquor: a novel strategy that combines the use of recombinant Bacillus subtilis and Candida maltosa

Directory of Open Access Journals (Sweden)

Jiang Mingguo

2011-02-01

Full Text Available Abstract Background Xylose mother liquor has high concentrations of xylose (35%-40% as well as other sugars such as L-arabinose (10%-15%, galactose (8%-10%, glucose (8%-10%, and other minor sugars. Due to the complexity of this mother liquor, further isolation of xylose by simple method is not possible. In China, more than 50,000 metric tons of xylose mother liquor was produced in 2009, and the management of sugars like xylose that present in the low-cost liquor is a problem. Results We designed a novel strategy in which Bacillus subtilis and Candida maltosa were combined and used to convert xylose in this mother liquor to xylitol, a product of higher value. First, the xylose mother liquor was detoxified with the yeast C. maltosa to remove furfural and 5-hydromethylfurfural (HMF, which are inhibitors of B. subtilis growth. The glucose present in the mother liquor was also depleted by this yeast, which was an added advantage because glucose causes carbon catabolite repression in B. subtilis. This detoxification treatment resulted in an inhibitor-free mother liquor, and the C. maltosa cells could be reused as biocatalysts at a later stage to reduce xylose to xylitol. In the second step, a recombinant B. subtilis strain with a disrupted xylose isomerase gene was constructed. The detoxified xylose mother liquor was used as the medium for recombinant B. subtilis cultivation, and this led to L-arabinose depletion and xylose enrichment of the medium. In the third step, the xylose was further reduced to xylitol by C. maltosa cells, and crystallized xylitol was obtained from this yeast transformation medium. C. maltosa transformation of the xylose-enriched medium resulted in xylitol with 4.25 g L-1·h-1 volumetric productivity and 0.85 g xylitol/g xylose specific productivity. Conclusion In this study, we developed a biological method for the purification of xylose from xylose mother liquor and subsequent preparation of xylitol by C. maltosa

77 FR 34981 - Stillaguamish Tribe of Indians-Liquor Control Ordinance

Science.gov (United States)

2012-06-12

... person who resides, conducts business, engages in a business transaction, receives benefits from the... liquor, wine, and beer, at a rate determined to be fair and equitable by the Board through independent...

Chemical composition and utilization of Hungarian spent sulfite liquor

Energy Technology Data Exchange (ETDEWEB)

Toth, B

1968-01-01

A review on the composition of Hungarian spent sulfite liquor and on its possible utilization, e.g., for the manufacturing of vanillin, yeast protein, or ethanol, as well as its direct utilization as a plasticizer for cement, additive for insecticides, or in adhesives.

40 CFR 430.03 - Best management practices (BMPs) for spent pulping liquor, soap, and turpentine management, spill...

Science.gov (United States)

2010-07-01

... gases from the cooking of softwoods by the kraft pulping process. Sometimes referred to as sulfate... professional judgment. [63 FR 18635, Apr. 15, 1998, as amended at 65 FR 46108, July 27, 2000] ...

Flavor Profile of Chinese Liquor Is Altered by Interactions of Intrinsic and Extrinsic Microbes.

Science.gov (United States)

Wu, Qun; Kong, Yu; Xu, Yan

2016-01-15

The flavor profile of Chinese liquor is the result of the metabolic activity of its microbial community. Given the importance of the microbial interaction, a novel way to control the liquor's flavor is by regulating the composition of the community. In this study, we efficiently improved the liquor's flavor by perturbing the intrinsic microbial metabolism with extrinsic microbes. We first constructed a basic microbial group (intrinsic) containing Saccharomyces cerevisiae, Wickerhamomyces anomalus, and Issatchenkia orientalis and added special flavor producers (extrinsic), Saccharomyces uvarum and Saccharomyces servazzii, to this intrinsic group. Upon the addition of the extrinsic microbes, the maximum specific growth rates of S. cerevisiae and I. orientalis increased from 6.19 to 43.28/day and from 1.15 to 14.32/day, respectively, but that of W. anomalus changed from 1.00 to 0.96/day. In addition, most volatile compounds known to be produced by the extrinsic strains were not produced. However, more esters, alcohols, and acids were produced by S. cerevisiae and I. orientalis. Six compounds were significantly different by random forest analysis after perturbation. Among them, increases in ethyl hexanoate, isobutanol, and 3-methylbutyric acid were correlated with S. cerevisiae and I. orientalis, and a decrease in geranyl acetone was correlated with W. anomalus. Variations in ethyl acetate and 2-phenylethanol might be due to the varied activity of W. anomalus and S. cerevisiae. This work showed the effect of the interaction between the intrinsic and extrinsic microbes on liquor flavor, which would be beneficial for improving the quality of Chinese liquor. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Price elasticity of demand for malt liquor beer: findings from a US pilot study.

Science.gov (United States)

French, Michael Thomas; Browntaylor, Didra; Bluthenthal, Ricky Neville

2006-05-01

Our objective is to estimate the relative price elasticity of demand for malt liquor beer (MLB), regular beer, hard liquor, and a combined group of all other alcoholic beverages. Three hundred and twenty-nine alcohol consumers (mostly male) in South-Central Los Angeles answered a series of questions pertaining to expected consumption responses to hypothetical price increases. We found that based on a 10% price increase, the mean price elasticity of demand (% change in quantity demanded / % change in price) was -0.79 for MLB drinkers, -1.14 for regular beer drinkers, -1.11 for hard liquor drinkers, and -1.69 for the combined group of all other drinkers. Logistic regression analysis revealed that the personal characteristics significantly related to being a MLB drinker were older age, not working, being homeless, and a daily drinker. Daily (or nearly daily) drinkers were more likely to be married, earning lower incomes, and hard liquor drinkers. This study is the first to investigate the price elasticity of demand for MLB drinkers and other heavy alcohol consumers in poor urban neighborhoods of the US. Future research can use the methods from this pilot study to more rigorously examine and compare the price sensitivity among heavy drinking groups.

Report on achievements in fiscal 1998. Demonstrative research of an alkali recovery process in the non-wood pulp paper manufacturing industry; 1998 nendo himokuzai pulp seishi sangyo arukari kaishu process ni kakawaru jissho kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This project is intended of performing demonstrative research jointly with China on a system to efficiently extract, condense, and combust black liquor in a non-wood pulp paper manufacturing plant in China to recover alkaline solution and heat energy, and to contribute to proliferation of the system. Specifically, an alkali recovery plant is built in Cangshan Paper Making Plant in Shandong Province to verify conservation in energy and reduction environmental load. This fiscal year has performed (1) component researches and related technology investigations, and (2) device design and fabrication. For Item 1, the extractor adopted the spiral net type, and the condensation device adopted the falling film evaporator of full-can plate type. For the silica removing agent, data were acquired on reduction of silica in the black liquor and effect of reducing the black liquor viscosity. Basic design requirements were established for an alkali recovery process for a pulp production plant of 75 t/d. Regarding Item 2, prepared were the material and heat balance tables for the black liquor extractor and the black liquor condenser, process flow diagrams (PFD), device specifications, a meter list, and a summary utility consumption list, and confirmed them with the Chinese side. For the black liquor combustion device and the caustification device, PFD and device list prepared by the Chinese side were acquired to start the basic design. (NEDO)

Pubs in Public Life: A Place for Liquor Spaces in the City of Vancouver

OpenAIRE

Forbes, Heather

2010-01-01

Vancouver liquor licensing bylaws has been described by members of the media, industry, government and general public as overly restrictive, especially in the areas of hours ofservice, geographical distribution and the cultural diversity ofpublic liquor spaces. According to the City of Vancouver, the objective of city stewardship is to provide for the social, economic and physical well-being of citizens. A consultation of both academic research and the Vancouver community suggests that public...

Washington State Spirits Privatization: How Satisfied were Liquor Purchasers Before and After, and by Type of Retail Store in 2014?

Science.gov (United States)

Greenfield, Thomas K; Williams, Edwina; Kerr, William C; Subbaraman, Meenakshi S; Ye, Yu

2017-11-27

In 2012 Washington State ended a wholesale/retail monopoly on liquor, permitting sale of spirits in stores with > 10,000 square feet. Implementation resulted in average price increases, but also five times the stores selling liquor. As part of a privatization evaluation, we studied pre-post and between-store-type purchase experiences. A 2010 Washington State Liquor Control Board (LCB) survey of liquor purchasers (n = 599), and the 2014 baseline of a repeated telephone survey (1,202 residents; n = 465 purchasers), each included 10 LCB questions on satisfaction with purchase experiences, each attribute with graded response scale A = 4 to D = 1 and F (0 = fail). Analyses used t-tests for satisfaction differences by time and analysis of variance (ANOVA) for 2014 between-store satisfaction-level differences. Five purchase features were rated more favorably after privatization (ps convenience, store hours, and prices (though price rated lowest both times); selection offered, courtesy, and checkout speed were unaltered, and number of staff and staff knowledge declined (both p convenience favored grocery and drug stores, and price satisfaction favored wholesale (Costco) stores, with staff knowledge highest at liquor stores. Satisfaction with liquor purchases increased after privatization for half the consumer experiences. Availability (location convenience and store hours) was important to liquor purchasers. Such results are relevant to sustained support for the policy of privatizing spirits retail monopolies.

EFEITO DA QUALIDADE DA MADEIRA NO DESEMPENHO DA POLPAÇÃO KRAFT

Directory of Open Access Journals (Sweden)

Danila Morais de Carvalho

2014-01-01

Full Text Available The aim of this study was to evaluate the wood quality in the kraft pulping performance under two different pulping conditions at two delignification degrees based on results for the yield, brightness, viscosity, and k/ kappa corrected index. Eucalyptus wood (A, B, and C was analyzed about their physicochemical properties (basic and apparent density, insoluble and soluble lignin content, extractive content, ash and insoluble ash in hydrochloric acid and used for pulp production by modified kraft cooking, using two different pulping conditions: Condition I (PI - 16.5% effective alkali, 30% sulfidity, and 155º of cooking temperature; and Condition II (PII - 17.5% effective alkali, 32% sulfidity,and 147ºC cooking temperature. Both conditions were performed to kappa number 15.5 ± 0.5 and 18.0 ± 0.5. The following pulping parameters and pulp properties produced were evaluated: H factor, screened yield, viscosity, brightness, hexenuronic acid content, and the k/kappa corrected index. The A wood, which had lower extractives and lignin content in its constitution, as well as lower basic and apparent density when compared with B and C woods, showed good results for cooking parameters, especially the pulp produced at PII condition at kappa number 18.0 ± 0.5.Also, the A wood showed higher screened yield, brightness, and viscosity comparing to the other pulps produced. Those pulps produced with higher kappa number have lower k/kappa corrected index.

D-Xylose from waste liquors of a viscose process

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, T; Mimura, M

1977-12-14

D-Xylose was prepared in good yields by neutralizing alkali waste liquors containing hemicellulose (I) with inorganic acids, dialyzing to remove salts hydrolyzing with acids, fermenting to decompose hexose, decolorizing, concentrating to < 15% sugars, treating with alcohols to precipitate oligosugars, removing the precipitate, and crystalizing. Thus, 1 kg waste liquor containing 27 g I was neutralized with 5% HCl, dialyzed at 15/sup 0/ for 48 h with parchment paper, concentrated at 40/sup 0/ to give a 500 g solution containing 7% H/sub 2/SO/sub 4/, boiled for 3 h, neutralized with BaCO/sub 3/, mixed with 10 g yeast at pH 5.4 to 5.8 (filtrate) fermented at 35/sup 0/ for 12 h, filtered, decolorized, concentrated at 40/sup 0/ to > 80 g mixed with EtOH to give a precipitate, filtered, concentrated to 17 g syrup, and mixed with AcOH to obtain 7.2 g D-Xylose.

Integrated Forest Products Refinery (IFPR)

Energy Technology Data Exchange (ETDEWEB)

van Heiningen, Adriaan R. P.

2010-05-29

Pre-extraction–kraft studies of hardwoods showed that when extracting about 10% of the wood, the final kraft pulp yield and physical properties could only be maintained at a level similar to that of regular kraft pulp when the final extract pH was close to neutral. This so-called “near neutral” pre-extraction condition at a level of 10% wood dissolution was achieved by contacting the wood chips with green liquor (GL) at a charge of about 3% (as Na2O on wood) at 160 °C for almost 2 hours (or an H-factor of about 800 hrs.). During subsequent kraft cooking of the pre-extracted hardwood chips the effective alkali charge could be reduced by about 3% (as Na2O on wood) and the cooking time shortened relative to that during regular kraft cooking, while still producing the same bleachable grade kappa number as the kraft control pulp. For softwood, no extraction conditions were discovered in the present investigation whereby both the final kraft pulp yield and physical properties could be maintained at a level similar to that of regular softwood kraft pulp. Therefore for hardwoods the “near- neutral green liquor pre-extraction conditions do meet the requirements of the IFPR concept, while for softwood, no extraction conditions were discovered which do meet these requirements. Application of simulated industrial GL at an extraction H-factor of about 800 hrs and 3% GL charge in a recirculating digester produced an hardwood extract containing about 4% (on wood) of total anhydro-sugars, 2% of acetic acid, and 1.3% of lignin. Xylan comprised of 80% of the sugars of which about 85% is oligomeric. Since only polymeric hemicelluloses and lignin may be adsorbed on pulp (produced at a yield of about 50% from the original wood), the maximum theoretical yield increase due to adsorption may be estimated as 10% on pulp (or 5% on wood). However, direct application of raw GL hardwood extract for hemicelluloses adsorption onto hardwood kraft pulp led to a yield increase of only

Direct heat transfer considerations for improving energy efficiency in pulp and paper Kraft mills

International Nuclear Information System (INIS)

Savulescu, Luciana Elena; Alva-Argaez, Alberto

2008-01-01

The success of any process improvement study depends on the quality of the available data and the way in which the plant-specific characteristics are incorporated in the applied conceptual models; in the context of process integration studies these issues are directly related to the rules followed during the data extraction stage. Improving energy efficiency in a pulp and paper Kraft mill requires the identification of the most promising heat recovery network retrofit projects. In a retrofit analysis using pinch technology/process integration methods, only the process streams associated to the existing heat exchangers and some outlet streams (such as wastewater/effluent streams and vents) with high potential for heat recovery are usually included, while the energy exchanged through non-isothermal stream mixing (NIM) or direct heat transfer (DHT) is often assumed fixed and is not considered in the analysis. Relaxing this assumption requires extracting more data to represent the DHT design configuration that exists in the plant. However, different data extraction options can be considered to represent the DHT configuration depending on the associated process/operation constraints. This work describes a systematic procedure to extract and analyse the impacts of DHT on the overall energy efficiency of a Kraft process with a specific focus on mixing along the pulp line and in water tanks

Uranium and thorium determination in Santa Quiteria liquor by ICP-OES analysis

International Nuclear Information System (INIS)

Pedro Junior, A.; Rezende, Paulo R.; Carvalho, Leonel M.; Ferreira, Elizabeth de Massena

2009-01-01

The mineral source of Itataia located in Santa Quiteria (Ceara/Brazil) is a phosphorus uraniferous one, where uranium occurs in collophanite (fluoroapatite) form. Phosphate minerals of the apatite family make possible the uses of uranium as a byproduct. The sulfuric leaching of the phosphate rock in order to obtain phosphoric acid also permits uranium recovery. Thus, the liquor coming from the leaching contains high levels of phosphoric acid as well as elements like Mg, Fe, U, Zr, Th and some rare earths in significant concentrations. The direct determination of U and Th content of this liquor is essential to a rapid response in the uranium separation and purification together process by solvent extraction, aiming its use for commercial purposes, as nuclear industry fuel. In this study U and Th were determined by Inductively Coupled Plasma Spectrometry (ICP-OES) in several samples of liquor, in high concentrations of H 3 PO 4 in environment. Several ratios of U/Th and H 3 PO 4 concentrations were studied, in order to find the optimal conditions for the direct determination of U and Th, without need to prior separation. (author)

QUALIDADE DA CELULOSE KRAFT-ANTRAQUINONA DE Eucalyptus dunnii PLANTADO EM CINCO ESPAÇAMENTOS EM RELAÇÃO AO Eucalyptus grandis E Eucalyptus saligna

OpenAIRE

Maria Cladis Mezzomo da Silva; Edvins Ratnieks; Teotônio Francisco de Assis; Celso Edmundo B. Foelkel; Jorge Vieira Gonzaga; Giovanni Willer Ferreira

1997-01-01

Este trabalho analisou o efeito de cinco espaçamentos de Eucalyptus dunnii (3 m x 1 m; 3 m x 1,5 m; 3 m x 2 m; 3 m x 3 m; 3 m x 4 m), para produção de celulose kraft-antraquinona, comparados com Eucalyptus grandis e Eucalyptus saligna (ambos no espaçamento 3 m x 2 m). Avaliaram-se a densidade básica e composição química da madeira original, analisando-se extrativos em diclorometano, pentosanas, lignina, solubilidade em NaOH8% e cinzas. Os cavacos foram submetidos a cozimento kraft-antraquinon...

Southern Pine Based on Biorefinery Center

Energy Technology Data Exchange (ETDEWEB)

Ragauskas, Arthur J. [Georgia Inst. of Technology, Atlanta, GA (United States); Singh, Preet [Georgia Inst. of Technology, Atlanta, GA (United States)

2013-12-20

This program seeks to develop an integrated southern pine wood to biofuels/biomaterials processing facility on the Recipient’s campus, that will test advanced integrated wood processing technologies at the laboratory scale, including: The generation of the bioethanol from pines residues and hemicelluloses extracted from pine woodchips; The conversion of extracted woodchips to linerboard and bleach grade pulps; and the efficient conversion of pine residues, bark and kraft cooking liquor into a useful pyrolysis oil.

Solvent extraction of uranium from lean grade acidic sulfate leach liquor with alamine 336 reagent

International Nuclear Information System (INIS)

Ramadevi, G.; Sreenivas, T.; Navale, A.S.; Padmanabhan, N.P.H.

2012-01-01

This paper describes the solvent extraction studies carried out on an acidic low assay uranium bearing leach liquor generated during sulfuric acid leaching of a refractory uranium ore using alamine 336-isodecenol-kerosene reagent combine. The leach liquor has a U 3 O 8 content of about 270 mg/L, free acidity 2.4 N H 2 SO 4 and total dissolved solids concentration of 260 g/L. Process parameteric variation studies indicated strong influence of free acidity of the leach liquor, alamine 336 concentration and aqueous to organic phase ratio on the extraction efficiency of uranium. An extraction efficiency of about 95% was achieved when the free acidity of leach liquor was 1 N H 2 SO 4 or lower, using 2% (v/v) alamine 336 at ambient temperature with an aqueous to organic phase ratio of 1:1. The loading capacity under these conditions was 1.2 g/L of U 3 O 8 . About 98% of the uranium values could be stripped from the loaded organic using 1 N NaCl in 0.2 N H 2 SO 4 . The solvent extraction studies aided in developing a suitable process flowsheet for treating refractory uranium ores which need high acidity during leaching and relatively lower acidity for purification by solvent extraction. (author)

Process integration study of a kraft pulp mill converted to an ethanol production plant – Part A: Potential for heat integration of thermal separation units

International Nuclear Information System (INIS)

Fornell, Rickard; Berntsson, Thore

2012-01-01

Energy efficiency is an important parameter for the profitability of biochemical ethanol production from lignocellulosic raw material. The yield of ethanol is generally low due to the limited amount of fermentable compounds in the raw material. Increasing energy efficiency leads to possibilities of exporting more by-products, which in turn might reduce the net production cost of ethanol. Energy efficiency is also an important issue when discussing the repurposing of kraft pulp mills to biorefineries, since the mills in question most likely will be old and inefficient. Investing in energy efficiency measures might therefore have a large effect on the economic performance. This paper discusses energy efficiency issues related to the repurposing of a kraft pulp mill into a lignocellulosic ethanol production plant. The studied process is a typical Scandinavian kraft pulp mill that has been converted to a biorefinery with ethanol as main product. A process integration study, using pinch analysis and process simulations, has been performed in order to assess alternative measures for improving the energy efficiency. The improvements found have also been related to the possibilities for by-product sales from the plant (electricity and/or lignin). In a forthcoming paper, which is the second part of this process integration study, an economic analysis based on the results from this paper will be presented. - Highlights: ► Conversion of a kraft pulp mill to ethanol production. ► Heat integration of distillation/evaporation in a lignocellulosic ethanol plant. ► Advanced pinch curves used to find new integration possibilities. ► 35–40% reduction of steam demand.

78 FR 4431 - Santee Sioux Nation-Title XXI-Alcohol, Chapter 1.-Santee Sioux Nation Liquor Control Ordinance

Science.gov (United States)

2013-01-22

... the sale and distribution of liquor and beer products on all properties within the limits of the... accommodations for the sale of liquor by the glass and for consumption on the premises. 3. ``Beer'' means any alcoholic beverage obtained by the alcoholic fermentation of an infusion or decoction of pure hops, or pure...

Context and consequences of liquor sachets use among young ...

African Journals Online (AJOL)

This article presents a relatively new phenomenon regarding alcohol related problems in Malawi; the context and consequences of the consumption of liquor sachets among young people. The results presented are part of a larger study looking at the prevalence and social norms related to alcohol use, as well as people's ...

78 FR 54670 - Miami Tribe of Oklahoma-Liquor Control Ordinance

Science.gov (United States)

2013-09-05

... operations on Miami Tribe of Oklahoma Trust Land. The enactment of a tribal ordinance governing liquor and... continued operation and strengthening of the tribal government and the delivery of tribal government... dining rooms of hotels, restaurants, theaters, gaming facilities, entertainment centers, stores, garages...

Lignin Structure and Aggregation Behavior in a Two-Component Ionic Liquid Solvent System

Directory of Open Access Journals (Sweden)

Susanne Bylin

2014-08-01

Full Text Available Ionic liquids are of potential interest in the processing of lignocellulosic biomass. In this study, the ionic liquid co-solvent system of 1-methylimidazole (MIM and 1-ethyl-3-methyl-imidazolium acetate (EMIMAc was used to solvate LignoBoost lignin fractionated from black liquor obtained from a kraft paper mill. Lignin ethanol-precipitated (LEP and ethanol-soluble (LES fractions were characterized via gel permeation chromatography (GPC and 13C- and 31P-nuclear magnetic resonance spectroscopy (NMR to determine structural characteristics and their relationship to polymer solubility in the system. Polymer integrity and solubility were optimal at ~20% lignin loading (w/w. Results showed that LEPs were generally of higher apparent molecular weight (Mw and enriched with condensed/aliphatic ether linkages and aliphatic hydroxyls. The LESs had a lower apparent Mw and were enriched with carboxylic and phenolic groups. This newly gained knowledge on lignin fractionation and aggregation in the present solvent system provides future opportunities for tuning fractionation/extraction to suit a specific biomass-derived product, e.g., carbon fibers.

Electrochemical treatment of evaporated residue of soak liquor generated from leather industry

International Nuclear Information System (INIS)

Boopathy, R.; Sekaran, G.

2013-01-01

Highlights: • Electrochemical treatment of evaporated residue of soak liquor (ERSL) generated in Tannery. • Copper coating on electrode surface and horizontal mounting of electrodes for ERSL treatment. • Electrochemical oxidation of organic pollutants under high saline condition. • The treated solution may be evaporated to dryness to get NaCl salt for hide/skin preservation. -- Abstract: The organic and suspended solids present in soak liquor, generated from leather industry, demands treatment. The soak liquor is being segregated and evaporated in solar evaporation pans/multiple effect evaporator due to non availability of viable technology for its treatment. The residue left behind in the pans/evaporator does not carry any reuse value and also faces disposal threat due to the presence of high concentration of sodium chloride, organic and bacterial impurities. In the present investigation, the aqueous evaporated residue of soak liquor (ERSL) was treated by electrochemical oxidation. Graphite/graphite and SS304/graphite systems were used in electrochemical oxidation of organics in ERSL. Among these, graphite/graphite system was found to be effective over SS304/graphite system. Hence, the optimised conditions for the electrochemical oxidation of organics in ERSL using graphite/graphite system was evaluated by response surface methodology (RSM). The mass transport coefficient (k m ) was calculated based on pseudo-first order rate kinetics for both the electrode systems (graphite/graphite and SS304/graphite). The thermodynamic properties illustrated the electrochemical oxidation was exothermic and non-spontaneous in nature. The calculated specific energy consumption at the optimum current density of 50 mA cm −2 was 0.41 kWh m −3 for the removal of COD and 2.57 kWh m −3 for the removal of TKN

Solar generation of hydrogen; Wasserstofferzeugung auf solarer Basis. Thermische Dissoziation des Wassers mit dem Licht-Kraft-Werk

Energy Technology Data Exchange (ETDEWEB)

Ziemba, G.

2003-04-01

Solar generation of hydrogen. The ''Licht-Kraft-Werke'' (LKW) is described. Due to this it will be possible to supply solid-state-lasers directly by sunlight. Supplied by lasers water should be split in a highest-temperature-reactor. An efficiency of more than 21% is supposed to be reached. (orig.)

Determination of thorium and uranium isotopes in the mining lixiviation liquor samples

International Nuclear Information System (INIS)

Reis Júnior, Aluísio de Souza; Monteiro, Roberto Pellacani Guedes

2017-01-01

The alpha spectrometric analysis refers to determination of thorium and uranium isotopes in the mining lixiviation liquor samples. The analytical procedure involves sample preparation steps for rare earth elements, thorium and uranium separation using selective etching with hydrofluoric acid and further radiochemical separation of these using TRU chromatographic resins (Eichrom Industries Inc. USA) besides electroplating of the isolated radionuclides. An isotopic tracer is used to determine the overall chemical yield and to ensure traceability to a national standard. The results are compared to results obtained for the same samples by Becquerel laboratory. We improved the method looking for reproducibility and isotopes isolation as required by alpha spectrometry and the method showing effective in analysis of mining liquor. (author)

Determination of thorium and uranium isotopes in the mining lixiviation liquor samples

Energy Technology Data Exchange (ETDEWEB)

Reis Júnior, Aluísio de Souza; Monteiro, Roberto Pellacani Guedes, E-mail: reisas@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2017-07-01

The alpha spectrometric analysis refers to determination of thorium and uranium isotopes in the mining lixiviation liquor samples. The analytical procedure involves sample preparation steps for rare earth elements, thorium and uranium separation using selective etching with hydrofluoric acid and further radiochemical separation of these using TRU chromatographic resins (Eichrom Industries Inc. USA) besides electroplating of the isolated radionuclides. An isotopic tracer is used to determine the overall chemical yield and to ensure traceability to a national standard. The results are compared to results obtained for the same samples by Becquerel laboratory. We improved the method looking for reproducibility and isotopes isolation as required by alpha spectrometry and the method showing effective in analysis of mining liquor. (author)

THE REACTIVITY OF PREHYDROLYZED SOFTWOOD KRAFT PULPS AFTER PROLONGED COOKING FOLLOWED BY CHLORITE DELIGNIFICATION

OpenAIRE

Ulf Germgard; Muhammad Asif Javed

2011-01-01

In a laboratory study high-quality spruce chips were prehydrolyzed to remove hemicelluloses and then kraft cooked to different kappa numbers by varying the cooking time. Each pulp sample was then chlorite delignified to selectively remove the remaining lignin. The reactivities of the pulp samples before and after chlorite delignification were determined by Fock’s test, which is supposed to measure the pulp’s reactivity in the conventional viscose process. A number of analyses were carried out...

Uranium recovery from acid leach liquors: Ix or Sx?

International Nuclear Information System (INIS)

Van Tonder, D.; Kotze, M.

2007-01-01

Various technologies for uranium recovery from sulphuric acid leach solutions were compared. Although the main consideration was the economics (Capex, recovery and Opex) of the various technologies and associated unit operations, other factors, such as flexibility, reliability, ease of operation, fire risk, stability with regards to feed flow variations, and feed solids content, would also need to be considered in the overall analysis. The design basis used for the comparison was a production rate or 200 kg/h U 3 O8 over a solution concentration range of 40 to 1500 mg/L U 3 O8. The technologies to be compared included Resin-in-pulp (RIP), Fixed-bed Ion Exchange (FBIX), Continuous Countercurrent Ion Exchange (CCIX, e.g. NIMCIX), and Solvent Extraction (Sx) using Bateman Pulsed Columns (BPC) and Bateman Settlers. Countercurrent Decantation (CCD) and clarification would be required for the Sx and FBIX technologies. The preliminary economic evaluation indicated that a flowsheet, comprising RIP for bulk uranium extraction and upgrade, followed by Sx, employing the BPC for purification of the RIP eluate stream, was the most economic option at leach liquor concentrations below 900 mg/L. Above 900 mg/L the economic evaluation suggested that CCDs followed by Sx in the BPC was the most economical processing option. For applications where the ore is abrasive and not amenable to RIP, due to the rate of resin consumption, Paste Thickeners to remove the bulk of the solids, followed by RIP, was found to be the most economic processing option at leach liquor concentrations below 200 mg/L. However, for leach liquor concentrations above 200 mg/L, a CCD-circuit followed by Sx using BPC was again the most economic favourable route

Evaluation of ogi liquor from different grains for antibacterial ...

African Journals Online (AJOL)

Administrator

2007-05-02

May 2, 2007 ... Antibiotic sensitivity pattern of the test organisms. This was done as above except that instead of making wells on the already seeded plates and pouring in the prepared liquors, standard commercial antibiotics disc was placed on the seeded agar plates before the plates were incubated at 37○C for 24 h.

PROFIL AROMA DAN MUTU SENSORI CITARASA PASTA KAKAO UNGGULAN DARI BEBERAPA DAERAH DI INDONESIA [Aroma and Flavor Sensory Profiles of Superior Cocoa Liquors from Different Regions in Indonesia

Directory of Open Access Journals (Sweden)

Intan Kusumaningrum*

2014-06-01

Full Text Available The objective of this research was to compare the aroma profiles and flavor sensory qualities of three cocoa liquors obtained from different regions in Indonesia, namely East Java, South Sulawesi and Bali. The Ghanaian cocoa liquor was used as the reference. The aroma of cocoa liquors was extracted by using a Solid Phase Microextraction (SPME, followed by detection with Gas Chromatography-Mass Spectrometry/Olfactometry (GC-MS/O with the Nassal Impact Frequency (NIF method. A total of 28 aroma active compounds in the cocoa liquors were identified, where in 21, 19, 22 and 18 compounds were detected in East Java, Bali, South Sulawesi and Ghana liquors, respectively. The profiles of these three liquors were not only different from one another but were also different from the reference. East Java liquor had a specific aroma of strong chocolate, enriched with creamy, caramel and coffee bean aroma, whileBali liquor was dominated by creamy, caramel and sweet, and South Sulawesi liquor was specified by its sweet green aroma. The aroma sensory characteristic was evaluated by descriptive test, presenting the aroma of nutty, acid, caramel, earthy and chocolate, while the taste sensory attributes included astringency, bitterness and acidity. The sensory profile analysis was carried out by applying a Quantitative Descriptive Analysis (QDA method. Accompired with preference and ranking tests were also conducted. Among the three cocoa liquors, the sensory profile of South Sulawesi was the most similar to that of Ghanaian cocoa liquor. However, the cocoa liquor from Bali and East Java cocoa were more preferred comparing to the liquor from South Sulawesi.

Jens Kraft og "De vilde Folk" (1760) - manden, forfatterskbet, værket

DEFF Research Database (Denmark)

Langkjær, Michael Alexander

2000-01-01

had "set cultural development in motion." 7. Brief Account of the Savage Peoples from 1760, together with an address to the Academy of Young Noblemen at Sorø and Critical Letters for the Betterment of Taste, both from 1761, might be viewed as an interrelated group of sources bearing on one particular...... as religious concerns. 9. Kraft's reactions, as revealed by the contradictory tendencies in Brief Account of the Savage Peoples, testify to his unease with the paradoxes of modernity and its concomitant sense of value-loss. The dissertation is divided into three volumes.The first volume introduces the subject...

Significance of the combined tests application in serum and liquor of patients with suspected neurosyphilis

Directory of Open Access Journals (Sweden)

Mirković Mihailo

2007-01-01

Full Text Available Background. Tertiary syphilis develops in 8-40% of untreated patients. It is most commonly manifested in the form of neurosyphilis, which can be asymptomatic taking the form of tabes dorsalis or progressive paralyze. Nowadays, in the developed countries, progressive paralyze is a rather rare disease, although the incidence of this disease has been rising within the last decades. Case report. We reported a 74-year-old male with the clinical image of dementia showing psychotic symptoms. On cytobiochemical examination of cerebrospinal liquor, hyperproteinorhacmia of 0.70 g/l with the normal number of cells was revealed. Computed tomography of the brain showed the marked cortical cerebral and cerebellar reduction changes with multiple ischemic lesions. Within a routine examination of patients with demention, we performed serologic reactions to syphilis out of which the Veneral Disease Researc Laboratory (VDRL test in serum and liquor was unreactive, while the Treponema pallidum hemagglutination (TPNA test in serum and liquor was positive. Positivity in serum and liquor was additionally confirmed by the Western blot method and fluoroscent treponema antibody (FTA test. The treatment with benzathine fenylpenicilline 2.4 g once weekly resulted in significant improving the psychotic symptoms of the disease even after two weeks. Conclusion. This case report showed that within the differential diagnostics in patients with demention or psychotic disorder it is obligatory to consider syphilis of the nervous system, as well as to apply a combination of various tests which, besides the typical liquor findings, significantly improve the accuracy of diagnosis. Such approach is especially important regarding the fact that neurosyphilis can remain clinically quite asymptomatic for a long period, which could lead to late therapy, while, on the contrary, an adequate and timely treatment can contribute to a significant recovery of any patients.

Complex microbiota of a Chinese "Fen" liquor fermentation starter (Fen-Daqu), revealed by culture-dependent and culture-independent methods

NARCIS (Netherlands)

Zheng, X.; Zheng, Y.; Han, B.; Zwietering, M.H.; Samson, R.A.; Boekhout, T.; Nout, M.J.R.

2012-01-01

Daqu is a traditional fermentation starter that is used for Chinese liquor production. Although partly mechanized, its manufacturing process has remained traditional. We investigated the microbial diversity of Fen-Daqu, a starter for light-flavour liquor, using combined culture-dependent and

Direct heat transfer considerations for improving energy efficiency in pulp and paper Kraft mills

Energy Technology Data Exchange (ETDEWEB)

Savulescu, Luciana Elena; Alva-Argaez, Alberto [Natural Resources (Canada)

2008-10-15

The success of any process improvement study depends on the quality of the available data and the way in which the plant-specific characteristics are incorporated in the applied conceptual models; in the context of process integration studies these issues are directly related to the rules followed during the data extraction stage. Improving energy efficiency in a pulp and paper Kraft mill requires the identification of the most promising heat recovery network retrofit projects. In a retrofit analysis using pinch technology/process integration methods, only the process streams associated to the existing heat exchangers and some outlet streams (such as wastewater/effluent streams and vents) with high potential for heat recovery are usually included, while the energy exchanged through non-isothermal stream mixing (NIM) or direct heat transfer (DHT) is often assumed fixed and is not considered in the analysis. Relaxing this assumption requires extracting more data to represent the DHT design configuration that exists in the plant. However, different data extraction options can be considered to represent the DHT configuration depending on the associated process/operation constraints. This work describes a systematic procedure to extract and analyse the impacts of DHT on the overall energy efficiency of a Kraft process with a specific focus on mixing along the pulp line and in water tanks. (author)

Adopting local alcohol policies: a case study of community efforts to regulate malt liquor sales.

Science.gov (United States)

McKee, Patricia A; Nelson, Toben F; Toomey, Traci L; Shimotsu, Scott T; Hannan, Peter J; Jones-Webb, Rhonda J

2012-01-01

To learn how the local context may affect a city's ability to regulate alcohol products such as high-alcohol-content malt liquor, a beverage associated with heavy drinking and a spectrum of nuisance crimes in urban areas. An exploratory, qualitative case study comparing cities that adopted policies to restrict malt liquor sales with cities that considered, but did not adopt policies. Nine large U.S. cities in seven states. City legislators and staff, alcohol enforcement personnel, police, neighborhood groups, business associations, alcohol retailers, and industry representatives. Qualitative data were obtained from key informant interviews (n = 56) and media articles (n = 360). The data were coded and categorized. Similarities and differences in major themes among and across Adopted and Considered cities were identified. Cities faced multiple barriers in addressing malt liquor-related problems, including a lack of enforcement tools, alcohol industry opposition, and a lack of public and political will for alcohol control. Compared to cities that did not adopt malt liquor sales restrictions, cities that adopted restrictions appeared to have a stronger public mandate for a policy and were less influenced by alcohol industry opposition and lack of legislative authority for alcohol control. Strategies common to successful policymaking efforts are discussed. Understanding the local context may be a critical step in winning support for local alcohol control policies.

Flow of Hydrolysed Polyacrylamide Mother Liquor through Filter Bag: Detecting the Effects of Formulation and Process Properties on Pressure Drop

Directory of Open Access Journals (Sweden)

Zi-Ming Feng

2016-01-01

Full Text Available Hydrolysed polyacrylamide (HPAM mother liquor is mainly used to extract oil. The HPAM solution is needed to filter the impurity using a bag filter before it is injected into the oil well. Therefore, the pressure drop of HPAM mother liquor must be less than 0.02 MPa in the processing of impurity filtration. The influence factors on pressure drop need to be researched. In this work, the computational fluid dynamics program (CFD was used to research some key influence factors on pressure drop, such as porosity, outlet pressure of filter, inlet flow rate and viscosity of mother liquor. The simulation results indicated that with increasing porosity, outlet pressure, inlet flow rate and mother liquor viscosity, the pressure drop had increased after flowing through the filter bag.

CFD Simulations of Soap Separation; CFD-simulering av avsaapning

Energy Technology Data Exchange (ETDEWEB)

Birkestad, Per

2010-07-01

A part of Vaermeforsk, the 'Skogsindustriella programmet', has identified the possibility to increase the production of tall oil, and hence the competitiveness, in Swedish pulp mills through an increase in the efficiency of the soap separation tanks. Currently, soap is extracted from the black liquor through a sedimentation process where the less dense soap rise to the top of the liquor tank where it is removed through a over-flow ducting at the top of the tank. Vaermeforsk seeks a better understanding of the detailed flow and the separation mechanisms within the liquor tanks and has initiated a study of computational fluid dynamics (CFD) of the tanks. The aim of the study has been threefold; To develop CFD-methods for use in the study of soap separation processes, to investigate the detailed flow within two Swedish liquor tanks and one North American soap skimmer and lastly to develop new design rules for use in future designs of soap separation tanks. The project shows that CFD is a useful tool for the investigation of black liquor and soap flow within a soap separation tank. The CFD simulations of three existing liquor tanks show that the previously used design-rules based on surface loads are inadequate as the actual flow velocities within the tanks are two orders of magnitude larger than those previously used as reference (the surface load). The CFD simulations also show that the black liquor flow, and hence the soap separation, is very sensitive to density variations on the black liquor inlet and temperature variations as small as 1 deg C can significantly affect the liquor flow.

Biodegradation of Ethyl Carbamate and Urea with Lysinibacillus sphaericus MT33 in Chinese Liquor Fermentation.

Science.gov (United States)

Cui, Kaixiang; Wu, Qun; Xu, Yan

2018-02-14

It is important to reduce the concentration of ethyl carbamate (EC) in fermented foods. However, controlling the formation of EC and its precursor urea is difficult in spontaneous food fermentation because urea is a natural product of nitrogen metabolism. Biodegradation is a better solution to reduce the concentration of EC. This study aimed to reduce the concentration of EC in Chinese liquor via an indigenous strain Lysinibacillus sphaericus MT33. This strain produced urethanase (940 U/L) and urease (1580 U/L) and degraded 76.52% of EC and 56.48% of urea. After inoculation in liquor fermentation, the maximal relative abundance of Lysinibacillus increased from 0.02% to 8.46%, the final EC and urea contents decreased by 41.77% and 28.15%. Moreover, the concentration of EC decreased by 63.32% in liquor. The negative correlation between abundance of Lysinibacillus and contents of EC and urea indicated the effect of L. sphaericus on EC and urea degradation.

Transcriptional characteristics associated with lichenysin biosynthesis in Bacillus licheniformis from Chinese Maotai-flavor liquor making.

Science.gov (United States)

Wu, Qun; Zhang, Rong; Peng, Suqin; Xu, Yan

2015-01-28

This work investigated the biosynthetic mechanism of lichenysin, the newly identified nonvolatile matrix component in Chinese liquors. Transcriptomes were analyzed in three producers, Bacillus licheniformis CGMCC 3961, 3962, and 3963, which were isolated from Maotai-flavor liquor-making process and produced 386.3, 553.5, and 795.2 μg/L lichenysin in a simulative liquor fermentation process. Lichenysin synthetase genes lchAA-AD in these three producers were expressed much more highly than those of the nonproducer B. licheniformis ATCC 14580 (>18.4-fold). In addition, ABC transporters were the most significant responsive metabolic pathway, and the expression levels of peptide transporter genes dppABCDE all increased more than 19.2-fold. When B. licheniformis CGMCC 3963 was cultured in synthetic medium, the expression of dppABCDE and lichenysin both increased with the addition of casein hydrolysate (containing various peptides). This indicated that peptide would act as a substrate for lichenysin synthesis. This work sheds new light on the mechanism for lichenysin biosynthesis.

Clarification of Orange Press Liquors by PVDF Hollow Fiber Membranes

Directory of Open Access Journals (Sweden)

Silvia Simone

2016-01-01

Full Text Available Press liquors are typical by-products of the citrus juice processing characterized by a high content of organic compounds and associated problems of environmental impact, which imply high treatment costs. However, these wastes contain a great number of health promoting substances, including fibers, carotenoids and phenolic compounds (mainly flavonoids, whose recovery against waste-destruction technologies is very attractive for new business opportunities. In this work, the clarification of orange press liquor by using microfiltration (MF membranes is studied as a preliminary step to obtain a permeate stream enriched in antioxidant compounds which can be further processed to produce extracts of nutraceutical and/or pharmaceutical interest. MF poly(vinylidene fluoride (PVDF hollow fibers were prepared by the dry/wet spinning technique. A series of fibers was produced from the same polymeric dope, in order to investigate the effect of selected spinning parameters, i.e., bore fluid composition and flowrate, on their properties. The morphology of the produced fibers was analyzed by Scanning Electron Microscopy (SEM. Fibers were further characterized for their mechanical properties, porosity, bubble point, pore size distribution and pure water permeability (PWP. Some of the produced fibers exhibited high permeability (pure water permeability ~530 L/m2·h·bar, coupled to good mechanical resistance and pore size in the range of MF membranes. These fibers were selected and used for the clarification of press liquor from orange peel processing. In optimized operating conditions, the selected fibers produced steady-state fluxes of about 41 L/m2·h with rejections towards polyphenols and total antioxidant activity of 4.1% and 1.4%, respectively.

Generation of PHB from Spent Sulfite Liquor Using Halophilic Microorganisms.

Science.gov (United States)

Weissgram, Michaela; Gstöttner, Janina; Lorantfy, Bettina; Tenhaken, Raimund; Herwig, Christoph; Weber, Hedda K

2015-06-08

Halophilic microorganisms thrive at elevated concentrations of sodium chloride up to saturation and are capable of growing on a wide variety of carbon sources like various organic acids, hexose and also pentose sugars. Hence, the biotechnological application of these microorganisms can cover many aspects, such as the treatment of hypersaline waste streams of different origin. Due to the fact that the high osmotic pressure of hypersaline environments reduces the risk of contamination, the capacity for cost-effective non-sterile cultivation can make extreme halophilic microorganisms potentially valuable organisms for biotechnological applications. In this contribution, the stepwise use of screening approaches, employing design of experiment (DoE) on model media and subsequently using industrial waste as substrate have been implemented to investigate the applicability of halophiles to generate PHB from the industrial waste stream spent sulfite liquor (SSL). The production of PHB on model media as well as dilutions of industrial substrate in a complex medium has been screened for by fluorescence microscopy using Nile Blue staining. Screening was used to investigate the ability of halophilic microorganisms to withstand the inhibiting substances of the waste stream without negatively affecting PHB production. It could be shown that neither single inhibiting substances nor a mixture thereof inhibited growth in the investigated range, hence, leaving the question on the inhibiting mechanisms open. However, it could be demonstrated that some haloarchaea and halophilic bacteria are able to produce PHB when cultivated on 3.3% w/w dry matter spent sulfite liquor, whereas H. halophila was even able to thrive on 6.6% w/w dry matter spent sulfite liquor and still produce PHB.

Neutralization of red mud with pickling waste liquor using Taguchi's design of experimental methodology.

Science.gov (United States)

Rai, Suchita; Wasewar, Kailas L; Lataye, Dilip H; Mishra, Rajshekhar S; Puttewar, Suresh P; Chaddha, Mukesh J; Mahindiran, P; Mukhopadhyay, Jyoti

2012-09-01

'Red mud' or 'bauxite residue', a waste generated from alumina refinery is highly alkaline in nature with a pH of 10.5-12.5. Red mud poses serious environmental problems such as alkali seepage in ground water and alkaline dust generation. One of the options to make red mud less hazardous and environmentally benign is its neutralization with acid or an acidic waste. Hence, in the present study, neutralization of alkaline red mud was carried out using a highly acidic waste (pickling waste liquor). Pickling waste liquor is a mixture of strong acids used for descaling or cleaning the surfaces in steel making industry. The aim of the study was to look into the feasibility of neutralization process of the two wastes using Taguchi's design of experimental methodology. This would make both the wastes less hazardous and safe for disposal. The effect of slurry solids, volume of pickling liquor, stirring time and temperature on the neutralization process were investigated. The analysis of variance (ANOVA) shows that the volume of the pickling liquor is the most significant parameter followed by quantity of red mud with 69.18% and 18.48% contribution each respectively. Under the optimized parameters, pH value of 7 can be achieved by mixing the two wastes. About 25-30% of the total soda from the red mud is being neutralized and alkalinity is getting reduced by 80-85%. Mineralogy and morphology of the neutralized red mud have also been studied. The data presented will be useful in view of environmental concern of red mud disposal.

Xylitol production from xylose mother liquor: a novel strategy that combines the use of recombinant Bacillus subtilis and Candida maltosa

OpenAIRE

Jiang Mingguo; Lv Jiyang; Wang Ben; Cheng Hairong; Lin Shuangjun; Deng Zixin

2011-01-01

Abstract Background Xylose mother liquor has high concentrations of xylose (35%-40%) as well as other sugars such as L-arabinose (10%-15%), galactose (8%-10%), glucose (8%-10%), and other minor sugars. Due to the complexity of this mother liquor, further isolation of xylose by simple method is not possible. In China, more than 50,000 metric tons of xylose mother liquor was produced in 2009, and the management of sugars like xylose that present in the low-cost liquor is a problem. Results We d...

75 FR 62853 - Reno-Sparks Indian Colony Liquor Control Ordinance

Science.gov (United States)

2010-10-13

... ordinance. (iii) ``Beer'' shall mean any beverage obtained by the alcoholic fermentation of any infusion or... alcohol, hydrated oxide or ethyl, or spirit or wine, which is commonly produced by the fermentation or... under Section V. (vi) ``Licensee'' shall mean the person or entity authorized to sell Liquor, Beer or...

Selective removal of chromium from sulphuric acid leach liquor of ...

African Journals Online (AJOL)

... removed in multiple batch extractions from the leach liquor and titanium losses were minimal (< 1%). The chromium content of extracted solutions was reduced to less than 1 ppm and thermal hydrolysis of these solutions yielded white titanium(IV) oxide pigments that are suitable for use in the coatings pigment industry.

Liquor oligoclonal bands assay: interpretation, correlation with other laboratory assays and importance for diagnostics of neurological disorders

OpenAIRE

Bagdonas, Dovydas

2017-01-01

Aim: to analyse the possible relationship between liquor IgG oligoclonal bands assay and other laboratory assays in neurological patients. Objectives: to determine the frequency of oligoclonal bands in neurological patients; to compare the results between serum and liquor laboratory assays in dependence of oligoclonal bands assay results; to evaluate the relationships between oligoclonal bands assay and serological-immunological assays for infectious diseases, gender, age and neurological ...

Uranium adsorption from the sulphuric acid leach liquor containing more chlorides with cation-exchange resin SL-406

International Nuclear Information System (INIS)

Hu Jun; Wang Zhaoguo; Chi Renqing; Niu Xuejun

1994-01-01

The feasibility of uranium adsorption was studied from the sulphuric acid leach liquor of a uranium ore containing more chlorides with cation-exchange resin SL-406. The influence of some factors on uranium adsorption was investigated. It was shown that the resin possesses better selectivity, stability and higher capacity. It can be effectively used to recovery uranium from leach liquors of uranium ores containing more chlorides

Kraft pulp bleaching with molybdenum activated acid peroxide (PMo stage)

International Nuclear Information System (INIS)

Rabelo, Marcos Sousa

2009-01-01

Optimum conditions to run the P Mo stage for bleaching eucalyptus kraft pulp were 90 deg C, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H 2 O 2 . The P Mo stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 deg C), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P Mo stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO. (author)

Performance of Side-Streams from Eucalyptus Processing as Sources of Polysaccharides and Lignins by Kraft Delignification

OpenAIRE

Paula C. R. Pinto; Cátia Oliveira; Carina Costa; Alírio Rodrigues

2016-01-01

The performance of bark, branches, sawdust, forest biomass, and short-rotation eucalyptus in kraft delignification to produce polysaccharides and lignin is reported and discussed. A positive correlation was found between pulping severity required for delignification and lignin reactivity. Among all, branches feedstock is the best source of polysaccharides due to the high pulp yield (48-54%) with a satisfactory delignification degree. Branches lignin was characterized for the first time, evalu...

Efeito dos sólidos dissolvidos da madeira na branqueabilidade e nas propriedades físico-mecânicas e ópticas de polpa kraft branqueada de eucalipto

Directory of Open Access Journals (Sweden)

Dalton Longue Júnior

2012-03-01

Full Text Available http://dx.doi.org/10.5902/198050985089Muitos estudos demonstram que o rendimento da polpação kraft pode ser melhorado pela readsorção de xilanas à polpa durante o cozimento, e o licor negro kraft contém fração significativa das xilanas da madeira, sendo uma importante fonte dessas macromoléculas. Porém, o efeito dessa técnica nas propriedades físico-mecânicas e ópticas de polpa branqueada de eucalipto, ainda não está bem esclarecido. Neste estudo foram produzidas polpas de eucalipto provenientes de cozimento kraft convencional, com diferentes adições de licor negro (0, 25, 50, 75 e 100 % v/v. Os cozimentos foram conduzidos até número kappa 17-18 e as polpas resultantes foram deslignificadas com oxigênio em condições fixas. O branqueamento foi realizado utilizando uma sequência DHT(EPDP até alvura final 92 % ISO. Em seguida as polpas foram refinadas num moinho PFI a diferentes níveis de revoluções (0, 500, 1.500, 3.000 e 6.000 e realizados testes de resistência ao rasgo, ao arrebentamento e à passagem de ar, alongamento, opacidade, densidade, volume específico aparente, capilaridade Klemm e índice de retenção de água (WRV. A eficiência e o ganho de alvura da pré-deslignificação com oxigênio foram ligeiramente prejudicados pela adição de licor negro ao cozimento kraft. A adição de 50 % de licor negro aos cozimentos resultou em polpas de pior branqueabilidade, sendo a demanda de cloro ativo aumentada em 5,3 kg/t celulose seca para obtenção de alvura 92 % ISO. As propriedades físico-mecânicas e ópticas das polpas kraft branqueadas não foram influenciadas, significativamente, pelo uso de licor negro no cozimento.

Effect of Microbial Interaction on Urea Metabolism in Chinese Liquor Fermentation

NARCIS (Netherlands)

Wu, Qun; Lin, Jianchun; Cui, Kaixiang; Du, Rubin; Zhu, Yang; Xu, Yan

2017-01-01

Urea is the primary precursor of the carcinogen ethyl carbamate in fermented foods. Understanding urea metabolism is important for controlling ethyl carbamate production. Using Chinese liquor as a model system, we used metatranscriptome analysis to investigate urea metabolism in spontaneous food

Kraft pulp bleaching with molybdenum activated acid peroxide (P{sub Mo} stage); Branqueamento de polpa celulosica kraft de eucalipto com peroxido acido ativado por molibdenio

Energy Technology Data Exchange (ETDEWEB)

Rabelo, Marcos Sousa [Servico Nacional de Aprendizagem Industrial (SENAI), Lauro de Freitas, BA (Brazil). Dept. Regional da Bahia; Silva, Vanessa Lopes; Barros, Denise Pires de; Colodette, Jorge Luiz [Universidade Federal de Vicosa (UFV), MG (Brazil). Dept. de Engenharia Florestal; Sacon, Vera Maria; Silva, Marcelo Rodrigues da [Votorantim Celulose e Papel, Jacarei, SP (Brazil)

2009-07-01

Optimum conditions to run the P{sub Mo} stage for bleaching eucalyptus kraft pulp were 90 deg C, pH 3.5, 2 h, 0.1 kg/t Mo and 5 kg/t H{sub 2}O{sub 2}. The P{sub Mo} stage efficiency increased with decreasing pH (1.5-5.5) and increasing temperature (75-90 deg C), time (2-4 h), and hydrogen peroxide (3-10 kg/t) and molybdenum concentration (0.1-0.4 kg/t). The implementation of the P{sub Mo} stage, as replacement for the A stage, decreased total active chlorine demand of the OAZDP sequence by 6 kg/t to reach 90% ISO, both in laboratory and mill scale. Such practice resulted in decreased bleaching chemical costs to produce fully bleached pulp of 90% ISO. (author)

Starter Culture Selection for Making Chinese Sesame-Flavored Liquor Based on Microbial Metabolic Activity in Mixed-Culture Fermentation

Science.gov (United States)

Wu, Qun; Ling, Jie

2014-01-01

Selection of a starter culture with excellent viability and metabolic activity is important for inoculated fermentation of traditional food. To obtain a suitable starter culture for making Chinese sesame-flavored liquor, the yeast and bacterium community structures were investigated during spontaneous and solid-state fermentations of this type of liquor. Five dominant species in spontaneous fermentation were identified: Saccharomyces cerevisiae, Pichia membranaefaciens, Issatchenkia orientalis, Bacillus licheniformis, and Bacillus amyloliquefaciens. The metabolic activity of each species in mixed and inoculated fermentations of liquor was investigated in 14 different cocultures that used different combinations of these species. The relationships between the microbial species and volatile metabolites were analyzed by partial least-squares (PLS) regression analysis. We found that S. cerevisiae was positively correlated to nonanal, and B. licheniformis was positively associated with 2,3-butanediol, isobutyric acid, guaiacol, and 4-vinyl guaiacol, while I. orientalis was positively correlated to butyric acid, isovaleric acid, hexanoic acid, and 2,3-butanediol. These three species are excellent flavor producers for Chinese liquor. Although P. membranaefaciens and B. amyloliquefaciens were not efficient flavor producers, the addition of them alleviated competition among the other three species and altered their growth rates and flavor production. As a result, the coculture of all five dominant species produced the largest amount of flavor compounds. The result indicates that flavor producers and microbial interaction regulators are important for inoculated fermentation of Chinese sesame-flavored liquor. PMID:24814798

Methylxanthine and catechin content of fresh and fermented cocoa beans, dried cocoa beans, and cocoa liquor

Directory of Open Access Journals (Sweden)

Pedro P. Peláez

2016-01-01

Full Text Available The theobromine and catechin content can affect the quality of cocoa liquor and is influenced by cacao variety, production area (PA, and fermentation, as well as the method of drying beans (FDB and cocoa liquor production (CLP. This study examined variationsin methylxanthine and catechin levels in fresh and fermented cocoa beans, dried cocoa grains, and in cocoa liquor from Trinitario, Criollo, and Forastero cacao varieties. A total of 123 cocoa bean samples from three Peruvian PAs at different altitudes, Tingo María (TM, San Alejandro (SA, and Curimana (CU, were evaluated. The theobromine (Tb and caffeine (Cf contents in fresh cocoa beans were affected by both cocoa type and PA. The caffeine content was higher in Trinitario cacao than in Criollo and Forastero varieties (p ≤ 0.05. The Tb and CF contents decreased in dry cocoa grain and was affected by FDB (p ≤ 0.05 (1.449 ± 0.004 to 1.140 ± 0.010 and 0.410 ± 0.03 to 0.165 ± 0.02 g Tb and C, respectively, per 100 g dry weight. Cocoa beans from Tingo María, which has thehighest altitude, had higher Tb and CF contents than those from other PAs. The catechin (C and epicatechin (EC contents were affected by the FDB and CLP, and were highestin fresh cocoa beans from the Tingo María area (range: 0.065 ± 0.01 to 0.020 ± 0.00 g C/100 g. The C and EC contents decreased during FDB and CLP (0.001 g C/100 g of cocoa liquor. Taken together, these results show that higher concentrations of Tb, Cf, C,and EC are present in fresh cocoa beans. Moreover, the cocoa variety influenced cocoa liquor quality. Overall, cocoa from the Tingo María PA had the most desirable chemical composition.

Investigation of boron extraction process with aid magnesium hydroxide from mother liquor of boron production

International Nuclear Information System (INIS)

Balapanova, B.S.; Zhajmina, R.E.; Serazetdinov, D.Z.

1988-01-01

Conditions of boron - magnesium concentrate preparation from mother liquor by coprecipitation of borate - ions by magnesium hydroxide are investigated. It is shown that boron - magnesium concentrate and products of its heat treatment at 100 - 500 deg C in water are dissolved partially, and in ammonium citrate - practically completely. Suppositions are made on the composition of the product prepared, on the the structure of its crystal lattice and the processes taking place in it during heat treatment. The conclusion is made on the perspectiveness of processing of mother liquor of boron industry for boron - magnesium concentrate

Membrane treatment of alkaline bleaching effluents from elementary chlorine free kraft softwood cellulose production.

Science.gov (United States)

Oñate, Elizabeth; Rodríguez, Edgard; Bórquez, Rodrigo; Zaror, Claudio

2015-01-01

This paper reports experimental results on the sequential use of ultrafiltration (UF), nanofiltration (NF) and reverse osmosis (RO) to fractionate alkaline extraction bleaching effluents from kraft cellulose production. The aim was to unveil the way key pollutants are distributed when subjected to sequential UF/NF/RO membrane separation processes. Alkaline bleaching effluents were obtained from a local pinewood-based mill, featuring elementary chlorine free bleaching to produce high-brightness cellulose. The experimental system was based on a laboratory-scale membrane system, DSS LabStak® M20 Alfa Laval, using Alfa Laval UF and NF/RO membranes, operated at a constant transmembrane pressure (6 bar for UF membranes and 32 bar for NF/RO membranes), at 25°C. Results show that 78% chemical oxygen demand (COD) and total phenols, 82% adsorbable organic halogens (AOX) and 98% colour were retained by UF membranes which have molecular weight cut-off (MWCO) above 10 kDa. In all, 16% of original COD, total phenols and AOX, and the remaining 2% colour were retained by UF membranes within the 1 to 10 kDa MWCO range. Chloride ions were significantly present in all UF permeates, and RO was required to obtain a high-quality permeate with a view to water reuse. It is concluded that UF/NF/RO membranes offer a feasible option for water and chemicals recovery from alkaline bleaching effluents in kraft pulp production.

Changes in Volatile Compounds of Chinese Luzhou-Flavor Liquor during the Fermentation and Distillation Process.

Science.gov (United States)

Ding, Xiaofei; Wu, Chongde; Huang, Jun; Zhou, Rongqing

2015-11-01

The aim of this study was to investigate the dynamic of volatile compounds in the Zaopei during the fermentation and distillation process by headspace solid-phase microextraction-gas chromatography mass spectrometry (HS-SPME-GCMS). Physicochemical properties analysis of Zaopei (fermented grains [FG], fermented grains mixed with sorghum [FGS], streamed grains [SG], and streamed grains mixed with Daqu [SGD]) showed distinct changes. A total number of 66 volatile compounds in the Zaopei were identified, in which butanoic acid, hexanoic acid, ethyl hexanoate, ethyl lactate, ethyl octanoate, hexyl hexanoate, ethyl hydrocinnamate, ethyl oleate, ethyl hexadecanoate, and ethyl linoleate were considered to be the dominant compounds due to their high concentrations. FG had the highest volatile compounds (112.43 mg/kg), which significantly decreased by 17.05% in the FGS, 67.12% in the SG, and 73.75% in the SGD. Furthermore, about 61.49% of volatile compounds of FGS were evaporated into raw liquor, whereas head, heart, and tail liquor accounted for 29.84%, 39.49%, and 30.67%, respectively. Each volatile class generally presented a decreasing trend, except for furans. Especially, the percentage of esters was 55.51% to 67.41% in the Zaopei, and reached 92.60% to 97.67% in the raw liquor. Principal component analysis based ordination of volatile compounds data segregated FGS and SGD samples. In addition, radar diagrams of the odor activity values suggested that intense flavor of fruit was weakened most from FG to SGD. The dynamic of volatile compounds in the Zaopei during the fermentation and distillation process was tested by SPME-GCMS. The result of this study demonstrated that both volatile compounds of Zaopei and thermal reaction during distillation simply determined the unique feature of raw liquor. This study was conducted based on the real products from liquor manufactory, so it is practicable that the method can be used in an industry setting. © 2015 Institute of Food

Inter-laboratory comparisons of hexenuronic acid measurements in kraft eucalyptus pulps using a UV-Vis spectroscopic method

Science.gov (United States)

J.Y. Zhu; H.F Zhou; Chai X.S.; Donna Johannes; Richard Pope; Cristina Valls; M. Blanca Roncero

2014-01-01

An inter-laboratory comparison of a UV-Vis spectroscopic method (TAPPI T 282 om-13 “Hexeneuronic acid content of chemical pulp”) for hexeneuronic acid measurements was conducted using three eucalyptus kraft pulps. The pulp samples were produced in a laboratory at kappa numbers of approximately 14, 20, and 35. The hexeneuronic acid contents of the three pulps were...

Utilization of Brewery Spent Grain Liquor by Aspergillus niger1

Science.gov (United States)

Hang, Y. D.; Splittstoesser, D. F.; Woodams, E. E.

1975-01-01

Aspergillus niger was found capable of rapidly converting about 97% of the sugar from brewery spent grain liquor to fungal mass. The yield of dry mycelium, based on the sugar consumed, was approximately 57%. This fungus produced 1.10% titratable acid calculated as citric acid and reduced the biochemical oxygen demand by 96%. PMID:1200633

The Effect of Iron Salt on Anaerobic Digestion and Phosphate Release to Sludge Liquor

Directory of Open Access Journals (Sweden)

Svetlana Ofverstrom

2011-12-01

Full Text Available Iron salts are used at wastewater treatment plants (WWTPs for several reasons: for removing chemical phosphorus, preventing from struvite formation and reducing the content of hydrogen sulfide (H2S in biogas. Anaerobic digestion is a common scheme for sludge treatment due to producing biogas that could be used as biofuel. Laboratory analysis has been carried out using anaerobic digestion model W8 (Armfield Ltd, UK to investigate any possible effect of adding FeCl3 on the anaerobic digestion of primary sludge (PS and waste activated sludge (WAS mixture as well as on releasing phosphates to digested sludge liquor. The obtained results showed that FeCl3 negatively impacted the anaerobic digestion process by reducing the volume of produced biogas. Fe-dosed sludge (max produced 30% less biogas. Biogas production from un-dosed and Fe-dosed sludge (min was similar to the average of 1.20 L/gVSfed. Biogas composition was not measured during the conducted experiments. Phosphorus content in sludge liquor increased at an average of 38% when digesting sludge without ferric chloride dosing. On the contrary, phosphate content in sludge liquor from digested Fe-dosed sludge decreased by approx. 80%.

A review of liquor transfer systems for use in nuclear reprocessing plants

International Nuclear Information System (INIS)

Singh, J.

1982-01-01

Liquor pumping systems for use in nuclear fuel reprocessing plants are described. Comparison of the operating characteristics and system constants are made between the air lift/Vacuum Operated Slug Lift, power fluidics and ejector pump systems. (author)

Kraft pulping and ECF bleaching of Eucalyptus globulus pretreated by the white-rot fungus Ceriporiopsis subvermispora - doi: 10.4025/actascitechnol.v34i3.12410

Directory of Open Access Journals (Sweden)

Claudio Salazar

2012-05-01

Full Text Available Eucalyptus globulus wood chips were decayed by the lignin-degrading fungus Ceriporiopsis subvermispora as a pretreatment step before kraft pulping. Weight and component losses of wood after the biotreatment were the following: weight (5%, glucans (1.5%, xylans (4.3%, lignin (5.7% and extractives (57.5%. The residual amount of lignin (expressed by the kappa number in pulps from biotreated wood chips was lower than that of pulps from the undecayed control. Depending on the delignification degree, kraft biopulps presented similar or up to 4% increase in pulp yield and 20% less hexenuronic acids (HexA than control pulps. The extended delignification with O2 decreases approximately 50% of the kappa number of the pulps and increases brightness, but had no effect in HexA reduction. The bleaching steps with chlorine dioxide (D0ED1 sequence decreased the kappa number up to 97%, increased pulp brightness up to 84% ISO and decreased HexA amount up to 91%. The use of C. subvermispora in biopulping of E. globulus generated important benefits during the production of kraft pulps that are reflected in a high pulp yield, low residual lignin content, low HexA amount, high brightness and viscosity of the biopulps as compared with pulps produced from untreated wood chips.

Size effects on acid bisulfite pretreatment efficiency: multiple product yields in spent liquor and enzymatic digestibility of pretreated solids

Science.gov (United States)

Yalan Liu; Jinwu Wang; Michael P. Wolcott

2017-01-01

Currently, feedstock size effects on chemical pretreatment performance were not clear due to the complexity of the pretreatment process and multiple evaluation standards such as the sugar recovery in spent liquor or enzymatic digestibility. In this study, we evaluated the size effects by various ways: the sugar recovery and coproduct yields in spent liquor, the...

Electrochemical treatment of evaporated residue of soak liquor generated from leather industry.

Science.gov (United States)

Boopathy, R; Sekaran, G

2013-09-15

The organic and suspended solids present in soak liquor, generated from leather industry, demands treatment. The soak liquor is being segregated and evaporated in solar evaporation pans/multiple effect evaporator due to non availability of viable technology for its treatment. The residue left behind in the pans/evaporator does not carry any reuse value and also faces disposal threat due to the presence of high concentration of sodium chloride, organic and bacterial impurities. In the present investigation, the aqueous evaporated residue of soak liquor (ERSL) was treated by electrochemical oxidation. Graphite/graphite and SS304/graphite systems were used in electrochemical oxidation of organics in ERSL. Among these, graphite/graphite system was found to be effective over SS304/graphite system. Hence, the optimised conditions for the electrochemical oxidation of organics in ERSL using graphite/graphite system was evaluated by response surface methodology (RSM). The mass transport coefficient (km) was calculated based on pseudo-first order rate kinetics for both the electrode systems (graphite/graphite and SS304/graphite). The thermodynamic properties illustrated the electrochemical oxidation was exothermic and non-spontaneous in nature. The calculated specific energy consumption at the optimum current density of 50 mA cm(-2) was 0.41 kWh m(-3) for the removal of COD and 2.57 kWh m(-3) for the removal of TKN. Copyright © 2013 Elsevier B.V. All rights reserved.

Efeito da adição da antraquinona na pré-deslignificação com oxigênio no branqueamento e na qualidade da polpa kraft de eucalipto

OpenAIRE

Silva, Mariléa Pinto da

2010-01-01

A produção de polpa kraft vem se destacando mundialmente devido às grandes vantagens do processo. Alguns estudos têm mostrado que a adição da antraquinona em licores de cozimento kraft traz efeitos positivos ao processo como aumento do rendimento, redução do número kappa e ganhos nas propriedades físicas da polpa. O objetivo principal deste trabalho é avaliar o efeito das diferentes dosagens de antraquinona da pré-deslignificação com oxigênio no branqueamento pela seqüência ODualD(EP)D, na qu...

Oil and gas activities in northern Norway. Summary; KonKraft rapport 6

Energy Technology Data Exchange (ETDEWEB)

2009-07-01

KonKraft report 6 deals with oil and gas operations on the Norwegian continental shelf (NCS) from Nordland county and northwards. It aims to contribute to a broad factual base for decision processes related to opening new exploration areas in these waters. The Norwegian petroleum sector employs about 250 000 people directly and indirectly. It accounts for a third of government revenues, and 90 per cent of its profits accrue to the state. NOK 119 billion of the central government budget in 2009 comes directly from oil and gas revenues. These funds finance roads, nursery schools, hospitals and the Norwegian welfare state. In addition, they safeguard future pensions. This industry is at a crossroads today. Oil production has dropped by 30 per cent since 2000. Recent forecasts from the Norwegian Petroleum Directorate show that it may be reduced by 50 per cent from its peak by 2013. Overall oil and gas output is expected to begin falling from the middle of the next decade. To slow this decline in output and revenues, the oil companies need access to new and attractive exploration acreage. Half the production expected by the government in 2030 relates to resources which have yet to be proven. Opening further areas of the NCS to petroleum activities would contribute to maintaining substantial investment and revenues for the community, and to continuing the development of industry in the northernmost parts of the country. The report reviews unopened areas along the Norwegian coast from the Helgeland region and north-eastwards to the Russian border. Nordland VI and VII plus Troms II are regarded by the petroleum industry as the most promising regions for big discoveries which could slow the production decline. The KonKraft 2 report concerning production development on the NCS estimates remaining resources in these three areas at 3.4 billion barrels of oil equivalent (boe). (Author)

Ultrafiltration and valorisation of lignin in black liquor from South African Kraft mills: A focus on dead-end stirred cell filtration

CSIR Research Space (South Africa)

Kekana, PT

2014-07-01

Full Text Available stream_source_info Kekana_2014_ABSTRACT.pdf.txt stream_content_type text/plain stream_size 1098 Content-Encoding ISO-8859-1 stream_name Kekana_2014_ABSTRACT.pdf.txt Content-Type text/plain; charset=ISO-8859-1 2014... International Conference on Chemical Thermodynamics and South African Institution of Chemical Engineering Conference, Durban International Convention Centre in Durban, South Africa, 27 July - 01 August 2014 Ultrafiltration and valorisation of lignin...

Physical properties of highly active liquor containing molybdate solids

International Nuclear Information System (INIS)

Dunnett, B.; Ward, T.; Roberts, R.; Cheeseright, J.

2016-01-01

The reprocessing of irradiated nuclear fuel at Sellafield produces a nitric acid based Highly Active Liquor (HAL) waste. The liquor, containing fission products and process additives, is concentrated in an evaporator in order to reduce the volume and is then stored in Highly Active Storage Tanks (HASTs) prior to vitrification. Caesium phosphomolybdate (CPM) is precipitated during the evaporation process and can convert to zirconium molybdate (ZM) during storage. During Post Operational Clean Out (POCO) of the HASTs, it is expected that their highly active content will be reduced by repeated cycles of washing using nitric acid and other reagents. Initial washings are likely to have a chemical composition comparable to concentrated HAL, becoming more dilute during the wash-out process. It is expected that the wash-out process will also recover significant quantities of molybdate solids (ZM, CPM or a mixture) from the HASTs. In order to determine the processing challenges from such washings during POCO, the physical properties of varying concentrations of non-active HAL simulants containing molybdate solids have recently been measured by the UK's National Nuclear Laboratory. The following measurements are presented and discussed: Particle size distribution; Density; Settling behaviour of solids; Voidage of settled sediment beds; Viscosity; Yield stress; And influence of ZM morphology on physical properties. (authors)

Physical properties of highly active liquor containing molybdate solids

Energy Technology Data Exchange (ETDEWEB)

Dunnett, B.; Ward, T.; Roberts, R. [National Nuclear Laboratory, Sellafield, Seascale, Cumbria, CA20 1PG (United Kingdom); Cheeseright, J. [Sellafield Ltd, Sellafield, Seascale, Cumbria, CA20 1PG (United Kingdom)

2016-07-01

The reprocessing of irradiated nuclear fuel at Sellafield produces a nitric acid based Highly Active Liquor (HAL) waste. The liquor, containing fission products and process additives, is concentrated in an evaporator in order to reduce the volume and is then stored in Highly Active Storage Tanks (HASTs) prior to vitrification. Caesium phosphomolybdate (CPM) is precipitated during the evaporation process and can convert to zirconium molybdate (ZM) during storage. During Post Operational Clean Out (POCO) of the HASTs, it is expected that their highly active content will be reduced by repeated cycles of washing using nitric acid and other reagents. Initial washings are likely to have a chemical composition comparable to concentrated HAL, becoming more dilute during the wash-out process. It is expected that the wash-out process will also recover significant quantities of molybdate solids (ZM, CPM or a mixture) from the HASTs. In order to determine the processing challenges from such washings during POCO, the physical properties of varying concentrations of non-active HAL simulants containing molybdate solids have recently been measured by the UK's National Nuclear Laboratory. The following measurements are presented and discussed: Particle size distribution; Density; Settling behaviour of solids; Voidage of settled sediment beds; Viscosity; Yield stress; And influence of ZM morphology on physical properties. (authors)

Oxidative pyrolysis of kraft lignin in a bubbling fluidized bed reactor with air

International Nuclear Information System (INIS)

Li, Dongbing; Briens, Cedric; Berruti, Franco

2015-01-01

Fast pyrolysis of kraft lignin with partial (air) oxidation was studied in a bubbling fluidized bed reactor at reaction temperatures of 773 and 823 K. The bio-oil vapors were fractionated using a series of three condensers maintained at desired temperatures, providing a dry bio-oil with less than 1% water and over 96% of the total bio-oil energy. Oxygen feed was varied to study its effect on yield, composition, and energy recovery in the gas, char and oil products. The addition of oxygen to the pyrolysis process increased the production of gases such as CO and CO 2 . It also changed the dry bio-oil properties, reducing its heating value, increasing its oxygen content, reducing its average molecular weight and tar concentration, while increasing its phenolics concentration. The lower reaction temperature of 773 K was preferred for both dry bio-oil yield and quality. Autothermal operation of the pyrolysis process was achieved with an oxygen feed of 72 or 54 g per kg of biomass at the reaction temperatures of 773 and 823 K, respectively. Autothermal operation reduced both yield and total energy content of the dry bio-oil, with relative reductions of 24 and 20% for the yield, 28 and 23% for the energy content, at 773 and 823 K. - Highlights: • Autothermal pyrolysis of Kraft lignin is possible with introduction of air. • Under autothermal conditions, 24% of the dry bio-oil chemicals are lost at 773 K. • Partial oxidation helps produce more simple phenols and less pyrolytic lignin. • Bio-oil from lignin pyrolysis has a very high phenolics concentration

76 FR 4366 - Iipay Nation of Santa Ysabel Liquor Control Law

Science.gov (United States)

2011-01-25

..., of liquor, as herein defined. Section 4.4. Beer. Any beverage obtained by the alcoholic fermentation..., which is commonly produced by the fermentation, or distillation of grain, starch, molasses or sugar, or... four percent (4%) of alcohol by weight shall be referred to as ``strong beer''. Section 4.5. Gaming...

Efficiency of 72h- fermented corn waste liquor as a potential source for

African Journals Online (AJOL)

okafor

tests. Equal concentrations of the LAB isolates at their determined peak ... Key Words: Probiotics, Lactic acid bacteria, Fermentation, Corn waste-liquor. ... diary products, decaying plants, intestinal tract and mucous membranes of animals and ...

Enzymes extracted from apple peels have activity in reducing higher alcohols in Chinese liquors.

Science.gov (United States)

Han, Qi'an; Shi, Junling; Zhu, Jing; Lv, Hongliang; Du, Shuangkui

2014-10-01

As the unavoidable byproducts of alcoholic fermentation, higher alcohols are unhealthy compounds widespread in alcoholic drinks. To investigate the activity of apple crude enzymes toward higher alcohols in liquors, five kinds of apple peels, namely, Fuji, Gala, Golden Delicious, Red Star, and Jonagold, were chosen to prepare enzymes, and three kinds of Chinese liquors, namely, Xifeng (containing 45% ethanol), Taibai (containing 50% ethanol), and Erguotou (containing 56% ethanol), were tested. Enzymes were prepared in the forms of liquid solution, powder, and immobilized enzymes using sodium alginate (SA) and chitosan. The treatment was carried out at 37 °C for 1 h. The relative amounts of different alcohols (including ethanol, 1-propanol, isobutanol, 1-butanol, isoamylol, and 1-hexanol) were measured using gas chromatography (GC). Conditions for preparing SA-immobilized Fuji enzymes (SA-IEP) were optimized, and the obtained SA-IEP (containing 0.3 g of enzyme) was continuously used to treat Xifeng liquor eight times, 20 mL per time. Significant degradation rates (DRs) of higher alcohols were observed at different degrees, and it also showed enzyme specificity according to the apple varieties and enzyme preparations. After five repeated treatments, the DRs of the optimized Fuji SA-IEP remained 70% for 1-hexanol and >15% for other higher alcohols.

Sacrificial Protective Coating Materials that can be Regenerated In-Situ to Enable High Performance Membranes

Energy Technology Data Exchange (ETDEWEB)

Malati, Peter; Ganguli, Rahul; Mehrotra, Vivek

2018-03-20

In the pulp and paper industry, weak black liquor concentration is carried out using energy intensive evaporators. Briefly, after wood digestion, water is evaporated to concentrate weak black liquor to the point where the black liquor can be burned in a recovery boiler, which ultimately leads to the recovery of digestion chemicals. Because it is less energy intensive than heat-driven separation, pressure-driven separation of water from black liquor using membranes could reduce the energy usage by 55 trillion Btu yr-1 and carbon dioxide emissions by more than 11 million metric tons CO2 per year if the first two evaporators are replaced. However, weak black liquor is a hot, corrosive, and highly fouling feed with organic molecules, colloids, and ions that clog membranes within hours of operation. We have shown that membrane-based concentration of weak black liquor is feasible, but only with our antifouling and anti-clogging technology that is based on a sacrificial Bio-inspired Living Skin concept. This concept is based on a conformal coating that is formed at the membrane surface and within the pores. Weak foulant adhesion dramatically decreases membrane fouling while the superhydrophilicity of the coating increases the water permeability. Moreover, the coating can be completely removed during backflushing, which removes foulants that may irreversibly adhere to the coating over long periods of time. The skin shedding completely regenerates the membrane surface and pores, restoring the original flux. This is followed by in-situ recoating, using the existing membrane plumbing and pumps, which essentially creates a brand new membrane surface. Our coatings resist fouling under hot weak black liquor concentration conditions and can be regenerated in-situ on demand. Weak black liquor permeate flux as well as Fourier-transform infrared spectroscopy results suggest that black liquor foulants adhere very weakly to coated membrane surfaces. We modified the coating process to

[The elixir of doctor Garrus. Drug or liquor? Original formula or imitation?].

Science.gov (United States)

Labrude, P

2010-04-01

Elixirs were formerly very used drugs or drinks. They are alcoholized and sugared, often offered as liquors, pleasant to drink, and contain drugs or not. Many are uncommon now, but Garrus elixir has passed through the centuries. Digestive stimulative, tonic, flavour of potions, aperitive and liquor, it is obtained by maceration of aloes, saffron, myrrh, clove, cinnamon and nutmeg in alcohol before distillation, then addition of vanilla, maiden-hair, orangeflower water and sugar. It seems to have been discovered at the end of the 17th century or the beginning of 18th century by Joseph Garrus, medicine doctor, living in Paris. When he died, in 1722, the elixir was already well known. During the Regency, it was administered to Duchess of Berry, who died nevertheless, and to some important members of the royal Court. During all the 18th century, it was considered as a panacea with many useful properties, inscribed in some pharmacopoeias and disposable in the drugstores. However, Garrus was acused of having simply improved the formula of the "élixir de propriété" of Paracelsius, also called tincture of aloes, myrrh and saffron. Taking in account the great number of formulas containing these same drugs and plants, it is difficult today to elucidate their origins and to discover who was imitated by another. The elixir of Doctor Garrus is also known in literature since its name is used in Madame Bovary and Tartarin sur les Alpes. At the beginning of our 21st century, some of us consider it as one of the best aperitive liquors.

The role of bound chlorine in the brightness reversion of bleached hardwood kraft pulp

Directory of Open Access Journals (Sweden)

Kátia Maria Morais Eiras

2009-01-01

Full Text Available Our previous paper showed fragmentary evidence that pulp brightness reversion may be negatively affected by its organically bound chlorine (OX content. A thorough investigation on eucalyptus kraft pulp led to the conclusion that OX increases reversion of certain pulps but this trend is not universal. Alkaline bleaching stages decrease reversion regardless of pulp OX content. Pulps bleached with high temperature chlorine dioxide revert less than those bleached with conventional chlorine dioxide in sequences ending with a chlorine dioxide stage but similarly in sequences ending with a final peroxide stage. The use of secondary condensate for pulp washing decreases reversion.

Electronic nose with a new feature reduction method and a multi-linear classifier for Chinese liquor classification

Energy Technology Data Exchange (ETDEWEB)

Jing, Yaqi; Meng, Qinghao, E-mail: qh-meng@tju.edu.cn; Qi, Peifeng; Zeng, Ming; Li, Wei; Ma, Shugen [Tianjin Key Laboratory of Process Measurement and Control, Institute of Robotics and Autonomous Systems, School of Electrical Engineering and Automation, Tianjin University, Tianjin 300072 (China)

2014-05-15

An electronic nose (e-nose) was designed to classify Chinese liquors of the same aroma style. A new method of feature reduction which combined feature selection with feature extraction was proposed. Feature selection method used 8 feature-selection algorithms based on information theory and reduced the dimension of the feature space to 41. Kernel entropy component analysis was introduced into the e-nose system as a feature extraction method and the dimension of feature space was reduced to 12. Classification of Chinese liquors was performed by using back propagation artificial neural network (BP-ANN), linear discrimination analysis (LDA), and a multi-linear classifier. The classification rate of the multi-linear classifier was 97.22%, which was higher than LDA and BP-ANN. Finally the classification of Chinese liquors according to their raw materials and geographical origins was performed using the proposed multi-linear classifier and classification rate was 98.75% and 100%, respectively.

Electronic nose with a new feature reduction method and a multi-linear classifier for Chinese liquor classification

International Nuclear Information System (INIS)

Jing, Yaqi; Meng, Qinghao; Qi, Peifeng; Zeng, Ming; Li, Wei; Ma, Shugen

2014-01-01

An electronic nose (e-nose) was designed to classify Chinese liquors of the same aroma style. A new method of feature reduction which combined feature selection with feature extraction was proposed. Feature selection method used 8 feature-selection algorithms based on information theory and reduced the dimension of the feature space to 41. Kernel entropy component analysis was introduced into the e-nose system as a feature extraction method and the dimension of feature space was reduced to 12. Classification of Chinese liquors was performed by using back propagation artificial neural network (BP-ANN), linear discrimination analysis (LDA), and a multi-linear classifier. The classification rate of the multi-linear classifier was 97.22%, which was higher than LDA and BP-ANN. Finally the classification of Chinese liquors according to their raw materials and geographical origins was performed using the proposed multi-linear classifier and classification rate was 98.75% and 100%, respectively

Hydrothermal Conversion of Neutral Sulfite Semi-Chemical Red Liquor into Hydrochar

Directory of Open Access Journals (Sweden)

Ramy Gamgoum

2016-06-01

Full Text Available Hydrochar was produced from neutral sulfite semi-chemical (NSSC red liquor as a possible bio-based solid fuel for use in power generation facilities. Hydrothermal conversion (HTC experiments were conducted using a fixed liquor-to-water volume ratio of 1:8 and reaction time of 3 h. Solutions were processed using different chemical additives, pH and temperature conditions to determine the optimum conditions required for producing a high energy content solid fuel. The hydrochar samples produced were analyzed by ultimate, thermogravimetric (TGA and Fourier transform infrared spectroscopy (FTIR analyses to determine physicochemical properties that are important for utilization as a fuel. The residual process liquids were also analyzed to better understand the effect of HTC process conditions on their properties. It was determined that the optimum conditions for producing a solid fuel was at a reaction temperature of 250 °C, in the presence of acetic acid at pH 3. The maximum energy content (HHV of the hydrochar produced from red liquor at this condition was 29.87 MJ/kg, and its ash content was 1.12 wt.%. This result reflects the effect of increasing reaction temperature on the physicochemical characteristics of the hydrochar. The increase of HTC temperature significantly reduces the ash content of the hydrochar, leads to a significant increase in the carbon content of the hydrochar, and a reduction in both the oxygen and hydrogen content. These effects suggests an increase in the degree of condensation of the hydrochar products, and consequently the formation of a high energy content material. Based on TGA and FTIR analyses, hydrochars prepared at high HTC temperature showed lower adsorbed moisture, hemicellulose and cellulose contents, with enrichment in content of higher temperature volatiles, such as lignin.

Physicochemical and functional properties of dietary fiber from maca (Lepidium meyenii Walp.) liquor residue.

Science.gov (United States)

Chen, Jinjin; Zhao, Qingsheng; Wang, Liwei; Zha, Shenghua; Zhang, Lijun; Zhao, Bing

2015-11-05

Using maca (Lepidium meyenii) liquor residue as the raw material, dietary fiber (DF) was prepared by chemical (MCDF) and enzymatic (MEDF) methods, respectively, of which the physicochemical and functional properties were comparatively studied. High contents of DF were found in MCDF (55.63%) and MEDF (81.10%). Both fibers showed good functional properties, including swelling capacity, water holding capacity, oil holding capacity, glucose adsorption capacity and glucose retardation index. MEDF showed better functional properties, which could be attributed to its higher content of DF, more irregular surface and more abundant monosaccharide composition. The results herein suggest that maca DF prepared by enzymatic method from liquor residue is a good functional ingredient in food products. Copyright © 2015 Elsevier Ltd. All rights reserved.

Kinetics of pulp mill effluent treatment by ozone-based processes

International Nuclear Information System (INIS)

Ko, Chun-Han; Hsieh, Po-Hung; Chang, Meng-Wen; Chern, Jia-Ming; Chiang, Shih-Min; Tzeng, Chewn-Jeng

2009-01-01

The wastewaters generated from wood pulping and paper production processes are traditionally treated by biological and physicochemical processes. In order to reduce chemical oxygen demand (COD) and color to meet increasingly strict discharge standards, advanced oxidation processes (AOPs) are being adapted as polishing treatment units. Various ozone-based processes were used in this study to treat simulated wastewaters prepared from black liquor from a hardwood Kraft pulp mill in Taiwan. The experimental results showed that the COD and color were primarily removed by direct ozone oxidation and activated carbon adsorption. While the addition of activated carbon could enhance the COD and color removal during ozonation, the addition of hydrogen peroxide improved the color removal only. For the various ozone-based treatment processes, kinetic models were developed to satisfactorily predict the COD and color removal rates. According to the kinetic parameters obtained from the various ozone-based processes, the enhanced COD and color removal of ozonation in the presence of activated carbon was attributed to the regeneration of the activated carbon by ozonation. These kinetic models can be used for reactor design and process design to treat pulping wastewater using ozone-based processes.

Effect of storage conditions on the shelf life of locally distilled liquor ...

African Journals Online (AJOL)

The purpose of this research was to determine the presence and levels of certain contaminants in akpeteshie from the various sources and to determine effects of ambient temperature, refrigeration, pasteurization and pasteurization in combination with low temperature for the liquor stored for seven weeks. The contaminant ...

Value Addition to Sulfate Waste Pickle Liquor of Steel Industry Using Hydrometallurgical Processes

Science.gov (United States)

Agrawal, Archana; Sahu, K. K.

2009-12-01

The solvent extraction of concentrated acid was investigated from sulfate waste pickle liquors using Cyanex 923 (trialkylphosphine oxide (TRPO); manufactured by Cytec Industries Inc., Woodland Park, NJ; provided by Cyanamid Canada Inc. (Markham, Canada)) as an extractant. The effect of various parameters was studied such as extractant concentration, organic-to-aqueous phase ratio, temperature. and retention time on acid extraction from the waste pickle liquor to the organic phase, After the saturation of the organic phase with sulfuric acid, stripping studies were performed to back-extract the pure acid into the aqueous phase. The raffinate of the solvent extraction process that contains both ferrous and ferric iron as well as trace impurities was subjected to oxidation and hydrothermal treatment to precipitate iron with a well-defined pseudo-cubic morphology and a high coercivity value that renders it suitable for high-grade ferrite production.

40 CFR 63.441 - Definitions.

Science.gov (United States)

2010-07-01

... Hazardous Air Pollutants from the Pulp and Paper Industry § 63.441 Definitions. All terms used in this... dioxide gas fortification process. Black liquor means spent cooking liquor that has been separated from... content and/or concentrating spent cooking liquor from the pulp washing system including pre-evaporators...

75 FR 23289 - Ponca Tribe of Indians of Oklahoma Liquor Control Ordinance

Science.gov (United States)

2010-05-03

... defined in this Ordinance. (b) ``Beer'' means any beverage obtained by the alcoholic fermentation of an... percent of Alcohol by weight shall be referred to as ``strong Beer.'' (c) ``Gaming Facility'' means a... herein defined (Alcohol, Spirits, Wine and Beer), and all fermented spirituous, vinous, or malt liquor or...

Methylated liquor treatment process in caffeine production

Science.gov (United States)

Zhou, Junbo; Yang, Mingyang; Huang, Wenjia; Cui, Shenglu; Gao, Liping

2018-02-01

The caffeine production process produces a large amount of sodium methyl sulphate in the methylated mother liquor. In order to recycle this part of ingredient, we use the mother liquid of Shijiazhuang Xin Nuowei Pharmaceutical Co., Ltd. as the object of study, the use of “nanofiltration (NF) - Dish Type Reverse Osmosis (DTRO) “combination of membrane technology for desalination and concentration. The experimental results show that the concentration of sodium sulfate in the nanofiltration solution is 0.37 g • L -1, the rejection rate is 98%, and the concentration of sodium methyl sulfate in DTRO concentrated solution is 453.80 g • L -1, which meets the requirements of the enterprise.

Influence of bleaching technologies on the aerobic biodegradability of effluents from Eucalyptus kraft pulps factories

Directory of Open Access Journals (Sweden)

Gladys Vidal

1999-01-01

Full Text Available Aerobic biodegradability of effluents from different Eucalyptus kraft pulp bleaching processes was studied. Bleaching effluents were obtained from: i Chlorine Bleaching (CB processes, with partial substitution of chlorine by chlorine dioxide and ii Total Chlorine Free (TCF processes. The overall biodegradability, in terms of Chemical Oxygen Demand (COD was higher for TCF effluents (96-98% than for CB ones (82-93%. Taking into account the higher organic load of CB effluents, this fact implied a much higher residual COD for them (100-180 mg/L than for TCF effluents (10-30 mg/L. Furthermore, a refractory fraction of molecular weight higher than 43,000 Da was found in CB effluent, which implied the necessity of a further specific treatment. The toxicity was completely removed after the biological treatmentA biodegradabilidade aerobica das águas residuais provenientes de diferentes procesos de branqueos de pulpa kraft foi estudada. Os efluentes são gerados no branqueo com cloro ou parcialmente sustituido com dioxido de cloro (CB ou bem em processos livres do cloro (TCF. A biodegradabilidade, quantificada como DQO foi maior para as águas do processo CB. Tendo em conta o elevado conteúdo orgânico do efluente CB obteinse uma maior concentraç&ão do DQO final neste efluente comparado com o efluente TCF. Uma fracçao recalcitrante maior a 43,000 Da no effluente BC foi encontrada, isto significa um tratamento adicional específico para sua eliminaçã o. A toxicidade foi totalmente eliminada despois do tratamento aeração.

78 FR 15037 - Bishop Paiute Tribe-Liquor Control Ordinance No. 2012-07

Science.gov (United States)

2013-03-08

..., purchase, gift, adjudication, executive order, Act of Congress, or other means of acquisition. .05 ``Tribal.../alcohol purchased on or off Tribal Lands is prohibited. Any person who is not licensed pursuant to this ordinance and who purchases liquor/alcoholic beverages on or off Tribal Lands and sells it on Tribal Lands...

High temperature attack of ores by a liquor containing essentially a soluble bicarbonate

International Nuclear Information System (INIS)

Maurel, Pierre; Nicolas, Francois; Bosca, Bernard.

1978-01-01

New process for high temperature oxidizing digestion of ores containing at least one metal in the uranium, vanadium and molybdenum group, by an aqueous liquor containing sodium bicarbonate and sodium carbonate in the presence of free oxygen insufflated into the reaction medium [fr

Influência dos atributos do solo sobre a qualidade da madeira de Pinus taeda para produção de celulose Kraft Influence of soil attributes on quality of Pinus taeda wood for cellulose Kraft production

Directory of Open Access Journals (Sweden)

Patrícia Aparecida Rigatto

2004-04-01

Full Text Available Neste trabalho foram analisados os efeitos dos atributos do solo sobre a qualidade da madeira de Pinus taeda para produção de celulose Kraft, em áreas da Klabin, em Telêmaco Borba-PR. Foram estudados oito sítios com árvores de 12 anos de idade, selecionados pelo tipo de solo, textura e vegetação primária. Para caracterização dos sítios foram realizadas coletas de amostras em três horizontes, tendo sido coletadas amostras indeformadas e compostas, analisando-se as seguintes variáveis no solo: densidade global, porosidade total, macroporosidade, disponibilidade de água, fertilidade e granulometria. Selecionaram-se cinco árvores médias por sítio, nas quais foram medidos as alturas total e comercial e o DAP e retirados discos, sendo este material ensaiado quanto a densidade básica, composição química, características morfológicas dos traqueídeos e produção de celulose Kraft. Com relação às propriedades da madeira, os atributos físicos do solo demonstraram ter maior influência. De modo geral, as madeiras provenientes de sítios com texturas mais argilosas apresentaram menores valores de densidade básica; maiores teores de extrativos e lignina; menores teores de holocelulose e celulose; traqueídeos mais curtos, mais largos, com paredes mais finas e com diâmetros do lúmen maiores; e menor rendimento em celulose. A partir destes resultados, concluiu-se ser possível a previsão de propriedades da polpa através da análise das características da madeira associada às condições edáficas reinantes.To meet the increasing demand for forest products, much of the future timber supply will come from trees grown in managed plantations. This work was carried out to analyze the effects of soil attributes on Pinus taeda wood quality to produce Kraft cellulose at Klabin Parana Cellulose Co., in Telêmaco Borba, PR, Brazil. The study focused on the influence of soil attributes on the anatomical, physical and chemical wood

Structural Alterations of Lignins in Transgenic Poplars with Depressed Cinnamyl Alcohol Dehydrogenase or Caffeic Acid O-Methyltransferase Activity Have an Opposite Impact on the Efficiency of Industrial Kraft Pulping1

Science.gov (United States)

Lapierre, Catherine; Pollet, Brigitte; Petit-Conil, Michel; Toval, Gabriel; Romero, Javier; Pilate, Gilles; Leplé, Jean-Charles; Boerjan, Wout; Ferret, Valérie; De Nadai, Véronique; Jouanin, Lise

1999-01-01

We evaluated lignin profiles and pulping performances of 2-year-old transgenic poplar (Populus tremula × Populus alba) lines severely altered in the expression of caffeic acid/5-hydroxyferulic acid O-methyltransferase (COMT) or cinnamyl alcohol dehydrogenase (CAD). Transgenic poplars with CAD or COMT antisense constructs showed growth similar to control trees. CAD down-regulated poplars displayed a red coloration mainly in the outer xylem. A 90% lower COMT activity did not change lignin content but dramatically increased the frequency of guaiacyl units and resistant biphenyl linkages in lignin. This alteration severely lowered the efficiency of kraft pulping. The Klason lignin level of CAD-transformed poplars was slightly lower than that of the control. Whereas CAD down-regulation did not change the frequency of labile ether bonds or guaiacyl units in lignin, it increased the proportion of syringaldehyde and diarylpropane structures and, more importantly with regard to kraft pulping, of free phenolic groups in lignin. In the most depressed line, ASCAD21, a substantially higher content in free phenolic units facilitated lignin solubilization and fragmentation during kraft pulping. These results point the way to genetic modification of lignin structure to improve wood quality for the pulp industry. PMID:9880356

Comment on 'evaluation of dechlorination mechanisms during anaerobic fermentation of blached kraft mill effluent by W.J. Parker, E.R. Hall and G.J. Farquhar'

Digital Repository Service at National Institute of Oceanography (India)

Sarkar, A.

Comment on "Evaluation of dechlorination mechanisms during anaerobic fermentation of bleached kraft mill effluent", is put forth. The data reproduced in Table 1 does not seem to be authentic as the method of preprationo of the chlorinated organic...

Utilização de surfactantes, na polpação kraft de madeira de eucalipto, como auxiliar na remoção de extrativos lipofílicos Surfactant utilization in kraft pulping of eucalyptus wood to improve lipophilic extractives removal

Directory of Open Access Journals (Sweden)

Deusanilde de Jesus Silva

2004-12-01

Full Text Available Problemas de deposição de "pitch" em fábricas de celulose e de papel são atribuídos aos extrativos lipofílicos existentes na madeira. Uma das maneiras mais eficientes de controlar essa deposição é através da remoção de seus precursores do sistema, logo que possível, nas etapas de cozimento, lavagem da polpa marrom e pré-deslignificação com oxigênio. O uso de surfactantes como aditivos da polpação tem sido investigado, mas há grande deficiência de informações técnicas, e a aplicação industrial é, ainda, incipiente. A proposta deste trabalho foi analisar a viabilidade de minimizar a deposição de "pitch", intensificando a remoção de suas substâncias precursoras na etapa de polpação pelo uso de tensoativos sintéticos com propriedades umectantes e solubilizantes. Foram testados 20 princípios ativos de surfactantes em cozimento kraft convencional de madeira de eucalipto. Os resultados, alguns estatisticamente significativos, apontaram redução do teor de substâncias lipofílicas na polpa marrom. Foi observado que a remoção dos extrativos lipofílicos da madeira é afetada, inversamente, pelo teor de óxido de eteno na molécula do surfactante. Outros parâmetros de cozimento, como deslignificação, rendimento, teor de rejeitos e viscosidade da polpa, foram também avaliados.Extractives are pitch precursors and may decrease pulping efficiency and affect pulp quality. Probably, the most efficient way to minimize pitch problems is to remove their precursors from the system during cooking, pulp washing and oxygen delignification. Use of surfactants as pulping additives has been investigated but technical information is deficient and industrial application is very incipient. The objective of this study was to analyze the performance of different surfactants as additives for kraft pulping of Eucalyptus wood. Twenty surfactants with different basic chemical structures were used. The results demonstrated that

Feasibility of recovery boiler in paper and pulp industry

International Nuclear Information System (INIS)

Rashid, H.

2010-01-01

in this paper feasibility of recovery boiler in terms of economics and environmental impacts in studied. Recovery boilers are employed in the pulp and paper industry where the cooking agent is recovered by burning black liquor. Cooking agent is exhausted due to the absorption of lignin (a burnable component) in cooking agent in the process of straw cooking. The process of recovery boiler is to remove lignin by combustion from black liquor, and heat is produced during the combustion of lignin which is used to produce steam. Recovery boiler is economical as it is recovering valuable chemicals and steam is produced as a byproduct. Steam from recovery boiler is also used for concentrating weak black liquor to concentrated black liquor recovering 50% of the utility water being used at the plant. The regenerated water in the form of foul condensate is reused in the process. The recovery of hazardous chemicals also reduces load of environmental pollution. Which otherwise can pollute the water reservoirs, and regeneration of water makes it environmentally friendly plant. Construction and challenges in operation of recovery boiler such as smelt-water explosion are also discussed in this paper. (author)

Production of ethoxylated fatty acids derived from Jatropha non-edible oil as a nonionic fat-liquoring agent.

Science.gov (United States)

El-Shattory, Y; Abo-Elwafa, Ghada A; Aly, Saadia M; Nashy, El-Shahat H A

2012-01-01

Natural fatty derivatives (oleochemicals) have been used as intermediate materials in several industries replacing the harmful and expensive petrochemicals. Fatty ethoxylates are one of these natural fatty derivatives. In the present work Jatropha fatty acids were derived from the non edible Jatropha oil and used as the fat source precursor. The ethoxylation process was carried out on the derived fatty acids using a conventional cheap catalyst (K₂CO₃) in order to obtain economically and naturally valuable non-ionic surfactants. Ethoxylation reaction was proceeded using ethylene oxide gas in the presence of 1 or 2% K₂CO₃ catalyst at 120 and 145°C for 5, 8 and 12 hours. The prepared products were evaluated for their chemical and physical properties as well as its application as non- ionic fat-liquoring agents in leather industry. The obtained results showed that the number of ethylene oxide groups introduced in the fatty acids as well as their EO% increased as the temperature and time of the reaction increased. The highest ethoxylation number was obtained at 145°C for 8 hr. Also, the prepared ethoxylated products were found to be effective fat-liquors with high HLB values giving stable oil in water emulsions. The fat-liquored leather led to an improvement in its mechanical properties such as tensile strength and elongation at break. In addition, a significant enhancement in the texture of the treated leather by the prepared fat-liquors as indicated from the scanning electron microscope (SEM) images was observed.

The Readership of Liquor Ads Employing Appeals to Affiliation, Achievement, and Product-Attributes.

Science.gov (United States)

Reid, Leonard N.; And Others

A study examined whether advertising appeals based on product affiliation, achievement, and attributes would account for differences in male readership of liquor advertisements. The investigation focused on the relationship between the content of alcholic beverage advertisements and attention engagement, the first state in consumer information…

Fast high-pressure freezing of protein crystals in their mother liquor

International Nuclear Information System (INIS)

Burkhardt, Anja; Warmer, Martin; Panneerselvam, Saravanan; Wagner, Armin; Zouni, Athina; Glöckner, Carina; Reimer, Rudolph; Hohenberg, Heinrich; Meents, Alke

2012-01-01

Protein crystals were vitrified using high-pressure freezing in their mother liquor at 210 MPa and 77 K without cryoprotectants or oil coating. The method was successfully applied to photosystem II, which is representative of a membrane protein with a large unit cell and weak crystal contacts. High-pressure freezing (HPF) is a method which allows sample vitrification without cryoprotectants. In the present work, protein crystals were cooled to cryogenic temperatures at a pressure of 210 MPa. In contrast to other HPF methods published to date in the field of cryocrystallography, this protocol involves rapid sample cooling using a standard HPF device. The fast cooling rates allow HPF of protein crystals directly in their mother liquor without the need for cryoprotectants or external reagents. HPF was first attempted with hen egg-white lysozyme and cubic insulin crystals, yielding good to excellent diffraction quality. Non-cryoprotected crystals of the membrane protein photosystem II have been successfully cryocooled for the first time. This indicates that the presented HPF method is well suited to the vitrification of challenging systems with large unit cells and weak crystal contacts

Replacement of soybean meal with maize steep liquor in the diets of ...

African Journals Online (AJOL)

Ferreira

2015-12-14

Dec 14, 2015 ... meal with maize steep liquor at 0%, 33%, 66% and 100% on a dry matter ... daily gain, hot carcass weight, cold carcass weight, hot carcass yield and ... remove impurities and separate the germ, gluten, starch and peel (USDA, 2010). ... are transferred to macerator tanks, which receive water with SO2 for ...

Studies on the antimicrobial effect of corn steep liquor on some ...

African Journals Online (AJOL)

Using well diffusion method, 0.1 ml (100 μl) of the liquor effectively inhibited the growth of the test organisms with zones of inhibition ranging from 4.00 ± 0.28 to 20.20 ± 0.14 mm. The zones of inhibition increased with increasing number of days of fermentation of the filtrate on which is the CSL. However, there was no ...

Characterization of volatile compounds in Fen-Daqu - a traditional Chinese liquor fermentation starter

NARCIS (Netherlands)

Van-Diep, L.; Zheng, X.; Chen, J.Y.; Han, B.Z.

2012-01-01

Fen-Daqu is a saccharifying agent and fermentation starter for the production of Chinese liquor Fen (alcoholic spirit) and Fen traditional vinegar. The volatile compounds produced at seven incubation steps were analysed by HS-SPME-GC-MS. A total of 83 major volatile compounds were identified,

Fractionation and cellulase treatment for enhancing the properties of kraft-based dissolving pulp.

Science.gov (United States)

Duan, Chao; Wang, Xinqi; Zhang, YanLing; Xu, Yongjian; Ni, Yonghao

2017-01-01

The aim of this study was to investigate a combined process involving pulp fractionation and cellulase treatment of each fraction for improving the molecular weight distribution (MWD) and reactivity of a kraft-based dissolving pulp. Three pulp fractions, namely long-fiber, mid-fiber and short-fiber fractions (LF, MF and SF, respectively), were used as the substrates. The results showed that the SF had the highest accessibility, lowest viscosity, and highest cellulase adsorption capacity, while the opposite was true for the LF. At a given viscosity, the combined process led to a lower polydispersity index (3.71 vs 4.98) and a higher Fock reactivity (85.6% vs 76.3%), in comparison to the conventional single-stage cellulase treatment. Copyright © 2016 Elsevier Ltd. All rights reserved.

A 3D CFD Simulation and Analysis of Flow-Induced Forces on Polymer Piezoelectric Sensors in a Chinese Liquors Identification E-Nose

Directory of Open Access Journals (Sweden)

Yu Gu

2016-10-01

Full Text Available Chinese liquors can be classified according to their flavor types. Accurate identification of Chinese liquor flavors is not always possible through professional sommeliers’ subjective assessment. A novel polymer piezoelectric sensor electric nose (e-nose can be applied to distinguish Chinese liquors because of its excellent ability in imitating human senses by using sensor arrays and pattern recognition systems. The sensor, based on the quartz crystal microbalance (QCM principle is comprised of a quartz piezoelectric crystal plate sandwiched between two specific gas-sensitive polymer coatings. Chinese liquors are identified by obtaining the resonance frequency value changes of each sensor using the e-nose. However, the QCM principle failed to completely account for a particular phenomenon: we found that the resonance frequency values fluctuated in the stable state. For better understanding the phenomenon, a 3D Computational Fluid Dynamics (CFD simulation using the finite volume method is employed to study the influence of the flow-induced forces to the resonance frequency fluctuation of each sensor in the sensor box. A dedicated procedure was developed for modeling the flow of volatile gas from Chinese liquors in a realistic scenario to give reasonably good results with fair accuracy. The flow-induced forces on the sensors are displayed from the perspective of their spatial-temporal and probability density distributions. To evaluate the influence of the fluctuation of the flow-induced forces on each sensor and ensure the serviceability of the e-nose, the standard deviation of resonance frequency value (SDF and the standard deviation of resultant forces (SDFy in y-direction (Fy are compared. Results show that the fluctuations of Fy are bound up with the resonance frequency values fluctuations. To ensure that the sensor's resonance frequency values are steady and only fluctuate slightly, in order to improve the identification accuracy of Chinese

QUALIDADE DA CELULOSE KRAFT-ANTRAQUINONA DE Eucalyptus dunnii PLANTADO EM CINCO ESPAÇAMENTOS EM RELAÇÃO AO Eucalyptus grandis E Eucalyptus saligna

Directory of Open Access Journals (Sweden)

Maria Cladis Mezzomo da Silva

1997-12-01

Full Text Available Este trabalho analisou o efeito de cinco espaçamentos de Eucalyptus dunnii (3 m x 1 m; 3 m x 1,5 m; 3 m x 2 m; 3 m x 3 m; 3 m x 4 m, para produção de celulose kraft-antraquinona, comparados com Eucalyptus grandis e Eucalyptus saligna (ambos no espaçamento 3 m x 2 m. Avaliaram-se a densidade básica e composição química da madeira original, analisando-se extrativos em diclorometano, pentosanas, lignina, solubilidade em NaOH8% e cinzas. Os cavacos foram submetidos a cozimento kraft-antraquinona com álcali ativo variando de 18,5 a 21% para obter um número kappa 17± 1,5; sulfidez a 8%, antraquinona base madeira 0,05%, relação licor/madeira 4:1, tempo até temperatura máxima 60 minutos, tempo à temperatura máxima 45 minutos. A celulose marrom resultante do cozimento kraft-antraquinona foi caracterizada e analisada em seus aspectos físico-químicos (rendimentos, rejeitos, número kappa, viscosidade intrínseca, alvura e solubilidade em NaOH5%. Uma parte desta sofreu refinação em moinho Jökro ao nível de 35°SR e, juntamente com a polpa não-refinada, foram submetidas a testes físico-mecânicos e óticos (resistência à tração, alongamento, estouro, rasgo, volume específico, alvura, resistência ao ar Gurley e ascensão capilar Klemm. O maior consumo de álcali ativo (20,5% ocorreu em espaçamento 3 m x 4 m, proporcionando maior degradação da polpa. Todos os espaçamentos caracterizados apresentaram viabilidade para a produção de celulose kraft-antraquinona, podendo proporcionar redução nos custos de produção de celulose, devido aos menores consumos apresentados de álcali ativo e madeira quando comparados com Eucalyptus grandis e Eucalyptus saligna. Os valores de extrativos e cinzas mostraram-se elevados para Eucalyptus dunnii, potencializando possíveis impactos em termos de incrustações e fechamento de circuito no processo fabril. Diante dos resultados obtidos, a celulose de Eucalyptus dunnii atende às exig

Qualidade da celulose kraft-antraquinona de Eucalyptus dunnii plantado em cinco espaçamentos em relação ao Eucalyptus grandis e Eucalyptus saligna.

OpenAIRE

Giovanni Willer Ferreira; Jorge Vieira Gonzaga; Celso Edmundo B. Foelkel; Teotônio Francisco de Assis; Edvins Ratnieks; Maria Cladis Mezzomo da Silva

2009-01-01

Este trabalho analisou o efeito de cinco espaçamentos de Eucalyptus dunnii (3 m x 1 m; 3 m x 1,5 m; 3 m x 2 m; 3 m x 3 m; 3 m x 4 m), para produção de celulose kraft-antraquinona, comparados com Eucalyptus grandis e Eucalyptus saligna (ambos no espaçamento 3 m x 2 m). Avaliaram-se a densidade básica e composição química da madeira original, analisando-se extrativos em diclorometano, pentosanas, lignina, solubilidade em NaOH8% e cinzas. Os cavacos foram submetidos a cozimento kraft-antraqu...

Remote age verification to prevent underage alcohol sales. First results from Dutch liquor stores and the economic viability of national adoption.

Science.gov (United States)

van Hoof, Joris J; van Velthoven, Ben C J

2015-04-01

Alcohol consumption among minors is a popular topic in the public health debate, also in the Netherlands. Compliance with the legal age limits for selling alcohol proves to be rather low. Some Dutch liquor stores (outlets with an exclusive license to sell off-premise drinks with 15% alcohol or more) have recently adopted a remote age verification system. This paper discusses the first results of the use of the system. We use data from 67 liquor stores that adopted Ageviewers, a remote age verification system, in 2011. A remote validator judges the customer's age using camera footage and asks for an ID if there is any doubt. The system then sends a signal to the cash register, which approves or rejects the alcohol purchase. From the 367346 purchase attempts in the database, 8374 were rejected or aborted for age-related reasons. This figure amounts to an average ratio of 1.12 underage alcohol purchase attempts per sales day in each participating liquor store. Scaling up to a national level, the figures suggest at least 1 million underage alcohol purchase attempts per year in Dutch liquor stores. Underage alcohol purchases can be prevented by the nationwide adoption of remote age verification. However, given the lax enforcement of the age limits by the government, adopting such a system on a voluntary basis is generally not in the economic interest of the liquor stores. Obligatory installation of the system in off-premise alcohol outlets may pass a social cost-benefit test if certain conditions are fulfilled. Copyright © 2014 Elsevier B.V. All rights reserved.

Dynamic modelling of nitrous oxide emissions from three Swedish sludge liquor treatment systems

DEFF Research Database (Denmark)

Lindblom, E.; Arnell, M.; Flores-Alsina, X.

2016-01-01

The objective of this paper is to model the dynamics and validate the results of nitrous oxide (N2O)emissions from three Swedish nitrifying/denitrifying, nitritation and anammox systems treating real anaerobic digester sludge liquor. The Activated Sludge Model No. 1 is extended to describe N2O...

EFFECT OF THE REACTION CONDITIONS OVER THE YIELD AND PROPERTIES OF METHYLCELLULOSE OBTAINED FROM PINUS RADIATA KRAFT BLEACHED CELLULOSE

OpenAIRE

TAPIA, C.; SAPAG-HAGAR, J.; ANDRADE, C.T.; HASSÓN, J.; VALENZUELA, F.; BASUALTO, C.

2002-01-01

Kraft bleached cellulose from Pinus radiata was submitted to methylation reactions in heterogeneous media. After activation with 29% (w/w) NaOH solution, methylation reactions were carried out both with dimethyl sulfate (DMS) and methyl iodide (MI). The effects of the pressing ratio, reaction time and type of methylation agent were studied. The better yields were obtained with dimethylsulphate and the pressing ratio and reaction time were not signficant over the yield. Methylcellulose (MC) of...

Caffeic acid production by simultaneous saccharification and fermentation of kraft pulp using recombinant Escherichia coli.

Science.gov (United States)

Kawaguchi, Hideo; Katsuyama, Yohei; Danyao, Du; Kahar, Prihardi; Nakamura-Tsuruta, Sachiko; Teramura, Hiroshi; Wakai, Keiko; Yoshihara, Kumiko; Minami, Hiromichi; Ogino, Chiaki; Ohnishi, Yasuo; Kondo, Ahikiko

2017-07-01

Caffeic acid (3,4-dihydroxycinnamic acid) serves as a building block for thermoplastics and a precursor for biologically active compounds and was recently produced from glucose by microbial fermentation. To produce caffeic acid from inedible cellulose, separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) reactions were compared using kraft pulp as lignocellulosic feedstock. Here, a tyrosine-overproducing Escherichia coli strain was metabolically engineered to produce caffeic acid from glucose by introducing the genes encoding a 4-hydroxyphenyllactate 3-hydroxylase (hpaBC) from Pseudomonas aeruginosa and tyrosine ammonia lyase (fevV) from Streptomyces sp. WK-5344. Using the resulting recombinant strain, the maximum yield of caffeic acid in SSF (233 mg/L) far exceeded that by SHF (37.9 mg/L). In the SSF with low cellulase loads (≤2.5 filter paper unit/g glucan), caffeic acid production was markedly increased, while almost no glucose accumulation was detected, indicating that the E. coli cells experienced glucose limitation in this culture condition. Caffeic acid yield was also negatively correlated with the glucose concentration in the fermentation medium. In SHF, the formation of by-product acetate and the accumulation of potential fermentation inhibitors increased significantly with kraft pulp hydrolysate than filter paper hydrolysate. The combination of these inhibitors had synergistic effects on caffeic acid fermentation at low concentrations. With lower loads of cellulase in SSF, less potential fermentation inhibitors (furfural, 5-hydroxymethyfurfural, and 4-hydroxylbenzoic acid) accumulated in the medium. These observations suggest that glucose limitation in SSF is crucial for improving caffeic acid yield, owing to reduced by-product formation and fermentation inhibitor accumulation.

The effect of varying air injection rates on tall oil soap skimming efficiency for low fatty acid/resin acid ratio soaps produced by pulping mountain pine beetle-infected wood

Energy Technology Data Exchange (ETDEWEB)

Uloth, V.; Guy, E. [FPInnovations, Prince George, BC (Canada). PAPRICAN Div.

2009-07-01

This study was conducted to assess the impact of higher air injection rates on the skimmer performance of an evaporator soap skimmer at a mill in British Columbia (BC). Tests previously indicated that only 13 to 38 percent of the total soap in the feed liquor was skimmed for low acid number and low fatty acid and resin acid ratio soaps. A 2-day trial demonstrated that there were extended periods when soap skimming stopped completely and soap levels in the liquor equalled or exceeded levels observed in the feed liquor. Higher air injection rates had little impact on soap-skimming efficiency. The higher air injection rates decreased soap density by approximately 8 percent, and increased black liquor entrainment in the skimmed soap by approximately 35 percent. The use of higher air injection rates was not recommended, as high percentages of black liquor are known to cause high H{sub 2}S emissions during soap acidulation. 16 refs., 1 tab., 5 figs.

Evaluation of bleachability on pine and eucalyptus kraft pulps

Directory of Open Access Journals (Sweden)

Marcela Freitas Andrade

2013-09-01

Full Text Available In recent decades, the pulp industry has been changing and improving its manufacturing processes in order to enhance production capacity, product quality and environmental performance. The aim of this study was to evaluate the bleachability effect on the efficient washing and alkaline leaching in eucalyptus and pine Kraft pulps using three different bleaching sequences: AD(EPD, A/D(EPDP and DHT(EPDP. This study was carried out in two stages. In the first part, the optimum conditions for pulp bleaching in order to achieve a brightness of 90% ISO were established. The second step was a comparative study between the pulps that received alkaline leaching and efficient washing with reference pulp (without treatment. The brightness, viscosity, kappa number and HexA in pulp were analyzed. The three sequences studied reached the desired brightness, but the sequence AD(EPD produced a lower reagent consumption for the same brightness. In the three sequences studied, the efficient washing of the pulp after oxygen delignification has contributed significantly to the removal of dissolved organic and inorganic materials in the pulp and the alkaline leaching decreased significantly the pulp kappa number due to a higher pulp delignification and bleachability.

MINERAL ELEMENTS IN WOODS OF EUCALYPTUS AND BLACK WATTLE AND ITS INFLUENCE IN A BLEACHED KRAFT PULP MILL

Directory of Open Access Journals (Sweden)

André Fredo

2009-09-01

Full Text Available Effluents are one of the most important problems in a pulp mill regarding to environmental subjects. With the purpose to reduce them, the mills are closing the internal cycles and reducing the water consumption. The wood, as the most significant source of non-process elements to the system, is responsible for some troubles to the industrial process. With the aim of evaluating their intake and to offer some informations for closing the loop, the contents of Al, Ca, Cu, Fe, K, Mg, Mn, Na, Ni, and Si were analysed in Acacia mearnsii, Eucalyptus dunnii, Eucalyptus globulus globulus, Eucalyptus grandis and Eucalyptus saligna woods. Wood samples were prepared by oven burning and acidic digestion methods, following analysis by ICP (inductively coupled plasm. Using also the results from silvicultural evaluation of trees and stands, they were calculated which elements were carried out from the site in larger amounts (K, Ca, Na, Al, Mn and Si and the species which exported largest amount of these elements (Eucalyptus dunnii and Eucalyptus globulus. The species with lower growth were Eucalyptus globulus and Eucalyptus dunnii, that leads to a bigger elements input and more potential industrial troubles. It was observed a range of 3.8 (Eucalyptus grandis up to 6 (Eucalyptus dunnii kg of analised mineral elements introduced to the process per ton of umbleached pulp produced. The Acacia mearnsii showed the lower level for Fe, Mn and Ni, being useful for oxygen, ozone and peroxide bleaching. The silicon observed in woods was in low concentration although the high values of this element in industrial liquor cycle. This leads to state that there is some contamination with soil when harvesting and handling the wood. Special care must be taken with both high ash and high mineral elements species, such as Eucalyptus dunnii and Eucalyptus globulus.

Assessment of reproductive effects in largemouth bass (Micropterus salmoides) exposed to bleached/unbleached kraft mill effluents.

Science.gov (United States)

Sepúlveda, M S; Ruessler, D S; Denslow, N D; Holm, S E; Schoeb, T R; Gross, T S

2001-11-01

This study evaluated the potential effects of different concentrations of bleached/unbleached kraft mill effluent (B/UKME) on several reproductive endpoints in adult largemouth bass (Micropterus salmoides). The kraft mill studied produces a 50/50 mix of bleached/unbleached market pulp with an estimated release of 36 million gal of effluent/day. Bleaching sequences were C90d10EopHDp and CEHD for softwood (pines) and hardwoods (mainly tupelo, gums, magnolia, and water oaks), respectively. Bass were exposed to different effluent concentrations (0 [controls, exposed to well water], 10, 20, 40, or 80%) for either 28 or 56 days. At the end of each exposure period, fish were euthanized, gonads collected for histological evaluation and determination of gonadosomatic index (GSI), and plasma was analyzed for 17beta-estradiol, 11-ketotestosterone, and vitellogenin (VTG). Largemouth bass exposed to B/UKME responded with changes at the biochemical level (decline in sex steroids in both sexes and VTG in females) that were usually translated into tissue/organ-level responses (declines in GSI in both sexes and in ovarian development in females). Although most of these responses occurred after exposing fish to 40% B/UKME concentrations or greater, some were observed after exposures to 20% B/UKME. These threshold concentrations fall within the 60% average yearly concentration of effluent that exists in the stream near the point of discharge (Rice Creek), but are above the <10% effluent concentration present in the St. Johns River. The chemical(s) responsible for such changes as well as their mode(s) of action remain unknown at this time.

Biobleaching chemistry of laccase-mediator systems on high-lignin-content kraft pulps

International Nuclear Information System (INIS)

Chakar, F.S.; Ragauskas, A.J.

2004-01-01

A high-lignin-content softwood kraft pulp was reacted with laccase in the presence of 1-hydroxybenzotriazole (HBT), N-acetyl-N-phenylhydroxylamine (NHA), and violuric acid (VA). The biodelignification response with violuric acid was superior to both 1-hydroxybenzotriazole and N-acetyl-N-phenylhydroxylamine. NMR analysis of residual lignins isolated before and after the biobleaching treatments revealed that the latter material was highly oxidized and that the magnitude of structural changes was most pronounced with the laccase - violuric acid biobleaching system. An increase in the content of carboxylic acid groups and a decrease in methoxyl groups were noted with all three laccase-mediator systems. The oxidation biobleaching pathway is directed primarily towards noncondensed C5 phenolic lignin functional structures for all three laccase-mediated systems. The laccase - violuric acid system was also reactive towards C5-condensed phenolic lignin structures. (author)

Selective removal of chromium from sulphuric acid leach liquor of ilmenite ore by solvent extraction with trioctylamine

Directory of Open Access Journals (Sweden)

E.O. Olanipekun

2000-12-01

Full Text Available The selective removal of chromium, a trace impurity that degrades the whiteness of titanium(IV oxide pigments, from sulphuric acid leach liquor of ilmenite, was investigated by solvent extraction with xylene solutions of trioctylamine. Important factors of commercial significance affecting the extraction operation have been examined. More than 99% of the chromium was selectively removed in multiple batch extractions from the leach liquor and titanium losses were minimal (< 1%. The chromium content of extracted solutions was reduced to less than 1 ppm and thermal hydrolysis of these solutions yielded white titanium(IV oxide pigments that are suitable for use in the coatings pigment industry.

Quality evaluation of dissolving pulp fabricated from banana plant stem and its potential for biorefinery.

Science.gov (United States)

Das, Atanu Kumar; Nakagawa-Izumi, Akiko; Ohi, Hiroshi

2016-08-20

The study was conducted to evaluate the quality of dissolving pulp of Musa sapientum L. (banana) plant stem and its potential for biorefinery. Introduction of pre-hydrolysis prior to any alkaline pulping process helps to reduce the content of hemicellulose and consequently produce acceptably high content of cellulose pulp. Water pre-hydrolysis was done at 150°C for 90min. The amount of lignin, xylan and glucan in the extracted pre-hydrolysis liquor (PHL) was 1.6, 4.9 and 1.6%, respectively. Pulping of pre-extracted chips was done following soda-AQ, alkaline sulfite and kraft process. The ratio of chip to liquor was 1:7 for both pre-hydrolysis and pulping. The kraft pulping process with 20% active alkali and 25% sulfidity at 150°C for 90min showed the best result. The lowest kappa number was 26.2 with a considerable pulp yield of 32.7%. The pulp was bleached by acidic NaClO2 and the consistency was 10% based on air-dried pulp. The lowest amount of 7% NaClO2 was used for the bleaching sequence of D0ED1ED2. After D0ED1ED2 bleaching, the pulp showed that α-cellulose, brightness and ash were 91.9, 77.9 and 1.6% respectively. The viscosity was 19.9cP. Hence, there is a possibility to use banana plant stem as a raw material for dissolving grade pulp and other bioproducts. Copyright © 2016 Elsevier Ltd. All rights reserved.

CLINICAL AND LIQUOR DIFFERENCES IN CASES OF SEROUS AND PURULENT MENINGITIS IN CHILDREN OF DIFFERENT AGE

Directory of Open Access Journals (Sweden)

E. M. Mazayeva

2014-01-01

Full Text Available The article presents features of clinical course and composition of cerebrospinal liquid in cases of purulent and serous meningitis depending on the age of the patients and the disease etiology. 40 children with bacterial purulent meningitis of meningococcal, hemophilic and unknown aetiology and 40 children with serous meningitis predominantly of enteroviral etiology were examined. The differences in duration and intensity of clinical symptoms, total protein concentration, and liquor cytosis were detected. The highest liquor indicators were revealed in the case of hemophilic meningitis in children of early age and in the case of meningococcal meningitis in children over seven years old. This fact can be explained by various pathogenic features of the causative agent and different compensatory reactions in children of different age. 

The reactivity of phenolic and non-phenolic residual kraft lignin model compounds with Mn(II)-peroxidase from Lentinula edodes.

Science.gov (United States)

Crestini, C; D'Annibale, A; Sermanni, G G; Saladino, R

2000-02-01

Three phenolic model compounds representing bonding patterns of residual kraft lignin were incubated with manganese peroxidase from Lentinula edodes. Extensive degradation of all the phenolic models, mainly occurring via side-chain benzylic oxidation, was observed. Among the tested model compounds the diphenylmethane alpha-5 phenolic model was found to be the most reactive, yielding several products showing oxidation and fragmentation at the bridging position. The non-phenolic 5-5' biphenyl and 5-5' diphenylmethane models were found unreactive.

Evaluation of the Addition liquor with high ammonia and Carbon Dioxide contentin the still 208 of the “Comandante Che Guevara” industry (ECG

Directory of Open Access Journals (Sweden)

María Elena Magaña-Haynes

2015-12-01

Full Text Available Adding fresh liquor through the 5th ring in still 208 of distilling liquor product (liquor obtained as a result of ammonium carbonate leaching of lateritic ore in the “Comandante Che Guevara” industry, were evaluated with the objective of reducing the dissolved nickel content of the effluent there from, as well as to improve the characteristics of the nickel carbonate which is delivered to the calcinations process. For the development of the survey, the same methodology used in 2001 for the test was applied. The results showed that by adding fresh liquor, it is possible to reduce the dissolved nickel content at the exit of the distillation column, so that the need for precipitation is minimized, thereby reducing the consumption of reagents and the and the cost for their acquisition. It was possible to corroborate the relationship between the content of NH3 at the discharge and the nickel dissolved therein appreciating that to achieve these results it is necessary to maintain the ammonia in the discharge between 1,0-1,8 g/L. The carbonate obtained in the column where liquor is added with high CO2 and NH3 reached high values of this last element in its composition and to the extent that increased sulphur content decreased. It was also seen an increase in the size of the coarse carbonates particles, which will influence in a decrease of energy consumption.

EFFECTS OF ALKALINE PRE-IMPREGNATION AND PULPING ON MALAYSIA CULTIVATED KENAF (HIBISCUS CANNABINUS

Directory of Open Access Journals (Sweden)

Lin Suan Ang

2010-05-01

Full Text Available This study was carried out to identify an appropriate alkaline pulping condition for Malaysia cultivated kenaf (Hibiscus cannabinus L.. The chemical composition of the kenaf bast and core fibers, and also whole stalk with different growing time were examined prior to pulping attempts. The results of various soda-AQ pulping showed that the degree of carbohydrate degradation and delignification increased with the increase of active alkali and cooking temperature, but decreased with the increase of liquor to material (L:M ratio. The most satisfactory properties of pulp and handsheets from bast could be attained by employing soda-AQ pulping with 19.4% active alkali, 0.10% AQ, and L:M ratio of 7:1 cooked for 2 hours at 160˚C. Besides, it was also found that a mild alkaline pre-impregnation prior pulping improved the pulp viscosity and handsheets’ strength properties, especially the tensile index and folding endurance effectively. Moreover, among the three alkaline pulping processes—kraft, kraft-AQ, and soda-AQ—the results of pulp and handsheet properties showed that the soda-AQ pulp was comparable or even slightly of higher quality than the kraft pulps. Between the unbeaten bast and core soda-AQ handsheets, the strength properties of the core were higher than the bast, as the thin-walled core fibers exhibited much better conformability than the thick-walled bast fibers.

Alkaline peroxide treatment of ECF bleached softwood kraft pulps: part 2. effect of increased fiber charge on refining, wet-end application, and hornification

Science.gov (United States)

Zheng Dang; Thomas Elder; Jeffery S. Hsieh; Arthur J. Ragauskas

2007-01-01

The effect of increased fiber charge on refining, cationic starch adsorption, and hornification was examined. Two pulps were investigated: (1) a softwood (SW) kraft pulp (KP) which was bleached elementally chlorine-free (ECF) and sewed as control; and (2) a control pulp treated with alkaline peroxide, which had a higher fiber charge. It was shown that increased fiber...

Characterization of Cypress Wood for Kraft Pulp Production

Directory of Open Access Journals (Sweden)

António J. A. Santos

2014-06-01

Full Text Available Wood samples of Cupressus arizonica, C. lusitanica, and C. sempervirens were evaluated for chemical, anatomical, and pulp characteristics as raw material for pulp production. Two 17-year-old trees per species were harvested, and wood samples were taken at a height of 2 m. Wood chips from Pinus pinaster (Portugal and P. sylvestris (Finland were used as references. C. arizonica differed from C. lusitanica and C. sempervirens with significantly lower (p < 0.05 tracheid diameter and wall thickness in the earlywood. The total extractives contents were 3.9%, 3.3%, and 2.5% for C. lusitanica, C. sempervirens, and C. arizonica, respectively, lower than the 5.1% for P. pinaster and 4.5% for P. sylvestris. Klason lignin content ranged from 33.0 to 35.6%, higher than the 28.0 to 28.7% for the pinewoods. The kraft pulp yields for C. arizonica, C. lusitanica, and C. sempervirens were 37.7%, 36.7%, and 38.7%, respectively, with kappa numbers of 32.0, 31.6, and 28.7, respectively; the yield values were 40.8% and 42.8%, with kappa numbers of 23.4 and 21.0, for P. pinaster and P. sylvestris, respectively. The cypress species are clearly different from pine in relation to wood pulping behavior. Among the cypress, C. sempervirens provided the best pulping results.

MRI in the liquor hypotension syndrome: a case report and review of literature

International Nuclear Information System (INIS)

Costa Machado Junior, Marcos Alberto da; Barbosa, Veronica Aline Oliveira; Taglietti, Isabella; D'Almeida Filho, Fernando.

1996-01-01

The case of a man is presented, who suddenly suffered headaches, with no other neurological disorder or clinical symptom, that partially remitted only in horizontal decubitus. The magnetic resonance imaging (MRI) investigation showed isointense dural thickening or detachment of the convexity in T1, that was hyperintense in T2. After contrast medium i.v. injection, MRI images showed diffuse and marked dural enhancement of the convexity, along the tentorium, at the base, in the upper cervix. Liquor hypotension, accompanied by dural thickening and enhancement visible by MRI have been reported in the literature. In this case, no loss of cerebrospinal fluid was identified as a possible cause for its reduced pressure. Within the frame work of essential liquor hypotension, the authors underline the postural nature of headaches, and hypothesizes the dural alterations are the expression of traction inducing tears in the dural border cell layer with consequent blood extravasation. The correlation of the radiological aspects with these alterations and their changes are discussed. (author). 11 refs., 2 figs

Production of red pigments by Monascus ruber in culture media containing corn steep liquor

Directory of Open Access Journals (Sweden)

P. S. Hamano

2006-12-01

Full Text Available The production of red pigments by Monascus ruber was evaluated utilizing complex culture media composed of glucose or sucrose (10 g/L, corn steep liquor (5 or 10 g/L and monosodium glutamate (0, 5.0, 7.6, 11.4 or 15.2 g/L. Medium containing 10 g/L glucose, 5 g/L corn steep liquor and 7.6 g/L monosodium glutamate resulted the highest values of extracellular red pigment absorbance (20.7 U and productivity (0.35 U/h. This medium also produced better results than using semi-synthetic medium with analytical grade reagents (12.4 U and 0.21 U/h. The cell growth was similar in both media (X @ 6.5 g/L, indicating that the capacity of the cells to produce red pigments was higher in complex culture media. In addition, in the complex culture medium, less of the intracellular red pigments accumulated than in semi-synthetic medium (9.1% and 30%, respectively.

The effect of temperature on the catalytic conversion of Kraft lignin using near-critical water

DEFF Research Database (Denmark)

Nguyen, Thi Dieu Huyen; Maschietti, Marco; Åmand, Lars-Erik

2014-01-01

The catalytic conversion of suspended LignoBoost Kraft lignin was performed in near-critical water using ZrO2/K2CO3 as the catalytic system and phenol as the co-solvent and char suppressing agent. The reaction temperature was varied from 290 to 370 C and its effect on the process was investigated...... in a continuous flow (1 kg/h). The yields of water-soluble organics (WSO), bio-oil and char (dry lignin basis) were in the ranges of 5–11%, 69–87% and 16–22%, respectively. The bio-oil, being partially deoxygenated, exhibited higher carbon content and heat value, but lower sulphur content than lignin. The main 1...

Process for purification of waste water produced by a Kraft process pulp and paper mill

Science.gov (United States)

Humphrey, M. F. (Inventor)

1979-01-01

The water from paper and pulp wastes obtained from a mill using the Kraft process is purified by precipitating lignins and lignin derivatives from the waste stream with quaternary ammonium compounds, removing other impurities by activated carbon produced from the cellulosic components of the water, and then separating the water from the precipitate and solids. The activated carbon also acts as an aid to the separation of the water and solids. If recovery of lignins is also desired, then the precipitate containing the lignins and quaternary ammonium compounds is dissolved in methanol. Upon acidification, the lignin is precipitated from the solution. The methanol and quaternary ammonium compound are recovered for reuse from the remainder.

Qualidade da celulose kraft-antraquinona de Eucalyptus dunnii plantado em cinco espaçamentos em relação ao Eucalyptus grandis e Eucalyptus saligna.

Directory of Open Access Journals (Sweden)

Giovanni Willer Ferreira

2009-09-01

Full Text Available Normal 0 21 false false false MicrosoftInternetExplorer4 Este trabalho analisou o efeito de cinco espaçamentos de Eucalyptus dunnii (3 m x 1 m; 3 m x 1,5 m; 3 m x 2 m; 3 m x 3 m; 3 m x 4 m, para produção de celulose kraft-antraquinona, comparados com Eucalyptus grandis e Eucalyptus saligna (ambos no espaçamento 3 m x 2 m. Avaliaram-se a densidade básica e composição química da madeira original, analisando-se extrativos em diclorometano, pentosanas, lignina, solubilidade em NaOH8% e cinzas. Os cavacos foram submetidos a cozimento kraft-antraquinona com álcali ativo variando de 18,5 a 21% para obter um número kappa 17± 1,5; sulfidez a 8%, antraquinona base madeira 0,05%, relação licor/madeira 4:1, tempo até temperatura máxima 60 minutos, tempo à temperatura máxima 45 minutos. A celulose marrom resultante do cozimento kraft-antraquinona foi caracterizada e analisada em seus aspectos físico-químicos (rendimentos, rejeitos, número kappa, viscosidade intrínseca, alvura e solubilidade em NaOH5%. Uma parte desta sofreu refinação em moinho Jökro ao nível de 35°SR e, juntamente com a polpa não-refinada, foram submetidas a testes físico-mecânicos e óticos (resistência à tração, alongamento, estouro, rasgo, volume específico, alvura, resistência ao ar Gurley e ascensão capilar Klemm. O maior consumo de álcali ativo (20,5% ocorreu em espaçamento 3 m x 4 m, proporcionando maior degradação da polpa. Todos os espaçamentos caracterizados apresentaram viabilidade para a produção de celulose kraft-antraquinona, podendo proporcionar redução nos custos de produção de celulose, devido aos menores consumos apresentados de álcali ativo e madeira quando comparados com Eucalyptus grandis e Eucalyptus saligna. Os valores de extrativos e cinzas mostraram-se elevados para Eucalyptus dunnii, potencializando possíveis impactos em termos de incrustações e fechamento de circuito no processo fabril. Diante dos resultados

Evaluation of incubated defatted rubber seed meal with sheep rumen liquor for Pangasius diet

Directory of Open Access Journals (Sweden)

Muhammad Agus Suprayudi

2015-10-01

Full Text Available ABSTRACT The research evaluated the use of rubber seed meal (Hevea brasiliensis; RBS incubated with sheep rumen liquor as a subtitution of soybean meal in catfish Pangasionodon sp. diet. The fish was cultured for 40 days and fed with the experimental diet containing RBS at five different diet compositions regarding to soybean meal substitution level, i.e. 0% (control, 12%, 23%, 34%, and 44%. Feeding was done three times a day to satiation. No significant different was found on fish-protein retention and survival rate in all treatments. Based on the study result, the use of rubber-seed meal (Hevea brasiliensis; RBS incubated with sheep rumen liquor could substitute soybean meal in catfish Pangasionodon sp. diet. Keywords: Hevea brasiliensis, Pangasionodon sp., catfish, sheep rumen liquor, rubber seed meal  ABSTRAK Penelitian ini mengevaluasi penggunaan tepung bungkil biji karet (Hevea brasiliensis; TBBK yang diinkubasi dengan cairan rumen domba sebagai pengganti tepung bungkil kedelai pada pakan ikan patin Pangasionodon sp. Pemeliharaan ikan dilakukan selama 40 hari dengan pemberian lima komposisi pakan berbeda sesuai tingkat substitusi tepung bungkil kedelai oleh tepung bungkil karet. TBBK yang ditambahkan untuk mengganti bungkil kedelai adalah sebesar 0%, 12%, 23%, 34% dan 44%. Pemberian pakan dilakukan selama tiga kali sehari secara at satiation. Tidak ditemukan perbedaan signifikan (P>0,05 pada nilai retensi protein dalam tubuh dan kelangsungan hidup ikan uji pada semua perlakuan. Berdasarkan hasil penelitian, dapat disimpulkan bahwa tepung bungkil biji karet yang diinkubasi dengan cairan rumen domba dapat digunakan sebagai pengganti bungkil kedelai pada pakan ikan patin Pangasionodon sp. Kata kunci: Hevea brasiliensis, Pangasionodon sp., patin, rumen domba, tepung biji karet 

Utilisation aspects of ashes and green liquor dregs from an integrated semichemical pulp and board mill

Energy Technology Data Exchange (ETDEWEB)

Manskinen, K.

2013-09-01

This thesis investigated the properties of bottom and fly ashes originating from a bubbling fluidised bed boiler (120 MW) using two different fuel mixtures (i.e. Fuel mixture A: coal, wood and peat; and B: wood and peat) and of the green liquor dregs originating from the associated semichemical pulp and board mill in relation to the potential utilisation of these residues from various aspects. The total concentrations of As, Cd, Cr, Cu, Ni, Pb, Zn and Hg in the bottom ashes were lower than the maximum allowable concentrations for these elements in forest fertilisers. The total Ca concentrations in bottom ashes A (2.4%; d.w.) and B (3.4%; d.w.) were lower than the legal requirement of 6.0% (d.w.) for ash used as a forest fertiliser. The total Ca concentrations in fly ashes A (6.4%; d.w.) and B (11.0%; d.w.) were higher than the minimum limit value of 6.0% (d.w.), but the concentration of As in fly ashes A (46.9 mg/kg d.w.) and B (41.3 mg/kg; d.w.) exceeded the maximum limit value of 40 mg/kg (d.w.). Only bottom ash B could be used as a forest fertiliser, provided some additional Ca is used. The bottom ashes both fulfilled the Finnish regulations on waste recovery in earth construction. Due to the elevated total concentration of PAH (23 mg/kg; d.w.) and extractable concentrations of Mo (3.9 mg/kg; d.w.) and Se (0.2 mg/kg; d.w.) in fly ash A, this residue cannot be used in covered structures. Due to the elevated concentration of PAH (90 mg/kg; d.w.) in fly ash B, this residue cannot be used in covered and paved structures. However, the utilisation of these residues as an earth construction agent is still possible, but an environmental permit would be required. According to the sequential extraction studies, extractable concentrations of most of the elements in the fly ash A were higher than those in the bottom ash A. The extractability of various elements, both in the bottom and fly ashes A, varied widely. Most of the elements did not occur as readily soluble and

Reductions in greenhouse gas emissions and oil use by DME (di-methyl ether) and FT (Fischer-Tropsch) diesel production in chemical pulp mills

Energy Technology Data Exchange (ETDEWEB)

Joelsson, Jonas M., E-mail: joelsson.jonas@hotmail.com [Ecotechnology and Environmental Science, Mid Sweden University, SE-831 25 Oestersund (Sweden); Gustavsson, Leif [Linnaeus University, SE- 351 95 Vaexjoe (Sweden)

2012-03-15

Using energy systems analysis, we examine the potential to reduce CO{sub 2} emissions and oil use by integrating motor biofuel production with pulp mills. BLG-DME (black liquor gasification with di-methyl ether production) is compared with solid biomass gasification with BIG-FT (solid biomass gasification with Fischer-Tropsch fuel production). The studied systems are expanded with stand-alone production of biomass-based electricity and motor fuel so that they yield the same functional unit in terms of motor fuel and electricity as well as pulp or paper product, in order to facilitate comparison. More motor biofuel can be produced in integration with the studied mills with BLG-DME than with BIG-FT because the black liquor flow is large compared with other fuel streams in the mill and the integration potential for BIG-FT is limited by the mill's heat demand. When both systems are required to produce the same functional unit, the BLG-DME system achieves higher system efficiency and larger reductions in CO{sub 2} emissions and oil use per unit of biomass consumed. In general, integration of motor biofuel production with a pulp mill is more efficient than stand-alone motor biofuel production. Larger reductions in CO{sub 2} emissions or oil use can, however, be achieved if biomass replaces coal or oil in stationary applications. -- Highlights: Black-Right-Pointing-Pointer CO{sub 2} emission and oil use reductions quantified for pulp mill-based biorefineries. Black-Right-Pointing-Pointer Black liquor gasification gives larger reductions than solid biomass gasification. Black-Right-Pointing-Pointer Lower mill steam demand increases the black liquor gasification advantage. Black-Right-Pointing-Pointer Biomass directly replacing coal or oil in stationary plants gives larger reductions.

Mystery shopping and alcohol sales: do supermarkets and liquor stores sell alcohol to underage customers?

NARCIS (Netherlands)

Gosselt, Jordi Franciscus; van Hoof, Joris Jasper; de Jong, Menno D.T.; Prinsen, Sander

2007-01-01

Purpose: The Dutch national policy regarding alcohol and youth relies on retailers’ willingness to refuse to sell alcohol to underage customers. This study examined unobtrusively whether supermarkets and liquor stores do indeed comply with the legal age restrictions for alcohol sales. - Methods: A

A LARCH BIOREFINERY: INFLUENCE OF WASHING AND PS CHARGE ON PRE-EXTRACTION PSAQ PULPING

Directory of Open Access Journals (Sweden)

Hanna S. Hörhammer

2012-06-01

Full Text Available This study deals with a biorefinery concept based on larch wood. Wood chips of Siberian larch (Larix sibirica Lebed. were treated with water before pulping at the optimal pre-extraction (PE condition of 150 °C and 90 minutes. Through PE, about 12.4% of the wood mass is dissolved, mainly from the arabinogalactan hemicellulose component. Fermentation of the hemicellulose-rich larch extract with Bacillus coagulans resulted in consumption of all C6 and C5 sugars and produced lactic acid in high yield. PE before pulping resulted in lower (4 to 5% pulp yield than for control kraft pulps. However, the pulp yield loss may be reduced by addition of polysulfide (PS and anthraquinone (AQ. The present study focuses on the effect of the degree of washing of the extracted chips and that of the PS charge in PSAQ pulping on the final properties of the pulp. Three different levels of washing and three different PS charges were tested. The characteristics of the extract, wash water, pulp, and black liquor samples were determined. The amount of sugars in the combined stream of collected extract and wash water obtained by mild washing was 10.2% on o.d. wood.

Excess heat from kraft pulp mills: Trade-offs between internal and external use in the case of Sweden-Part 1: Methodology

International Nuclear Information System (INIS)

Svensson, Inger-Lise; Joensson, Johanna; Berntsson, Thore; Moshfegh, Bahram

2008-01-01

Excess heat from a kraft pulp mill can be used either internally to increase the level of efficiency in the mill, or externally for example as district heating. This paper presents an approach to investigate the competition between external and internal use through modelling the pulp mill and an energy company (ECO) within the same system boundary. Three different sizes of ECOs with different district heating demands are studied. To investigate the competitiveness of using industrial excess heat as district heating compared with other heat production techniques, the option of investing in excess heat use is introduced, along with the possibility for the ECO to invest in biomass combined heat and power (CHP), waste CHP and natural gas combined cycle (NGCC). To evaluate the robustness of the model, alternative solutions are identified and will be used as a comparison to the optimal solutions. The model has been verified by comparing the results with previous studies concerning kraft pulp mills and with related studies regarding district heating and real ECOs. Finally, the approach presented in this part of the study will be used in the second part in order to investigate the trade-off between internal and external use of excess heat under different future energy market scenarios

Caracterização tecnológica, para produção de celulose, da nova geração de clones de Eucalyptus do Brasil Technological characterization of the new generation of Eucalyptus clones in Brazil for kraft pulp production

Directory of Open Access Journals (Sweden)

José Lívio Gomide

2005-02-01

Full Text Available Foram analisados clones de Eucalyptus de última geração, pertencentes às principais empresas brasileiras de celulose. Os estudos consistiram numa caracterização tecnológica detalhada da qualidade das madeiras utilizadas no processamento fabril das empresas. Foram realizadas análise químicas detalhadas das madeiras e cozimentos kraft, simulando-se uma das modernas técnica de digestor contínuo. Os resultados indicaram a alta qualidade dos clones de Eucalyptus atualmente plantados no Brasil para produção de celulose.Last generation of Eucalyptus clones pulped by the main Brazilian kraft pulp mills were used for this study. Detailed chemical analysis of the woods were carried out to establish the wood quality. Laboratory simulation of a modern continuous digester technique was used for pulp production. Results demonstrated the high quality of Eucalyptus clones wood that are being planted in Brazil for kraft pulp production.

Performance of Schizolobium amazonicum Wood in Bleached Kraft Pulp Production

Directory of Open Access Journals (Sweden)

Camila Sarto

2015-05-01

Full Text Available This study aimed to evaluate the characteristics of Schizolobium amazonicum wood, specifically its performance in bleached kraft pulp production and the characteristics of its pulp. Chips of Schizolobium amazonicum and Eucalyptus grandis x Eucalyptus urophylla (reference were used. The following parameters were evaluated in the wood: basic density, total extractives, total lignin, holocellulose, and fiber morphology. The pulping simulations were carried out in a laboratory digester, with parameters set to obtain pulp with kappa number 19 ± 0.5. Both pulps were bleached in a PFI mill and submitted to physical-mechanical tests. The results showed that S. amazonicum wood has low basic density and higher content of extractives when compared to E. grandis x E. urophylla wood. For pulping, S. amazonicum required higher alkali charge and H factor to achieve the same delignification level of E. grandis x E. urophylla, resulting in a lower yield, pulp with lower viscosity, and higher wood specific consumption. During bleaching, the brightness gain and final viscosity of S. amazonicum pulp were lower than E. grandis x E. urophylla pulp. Moreover, S. amazonicum pulp had worse physical-mechanical characteristics than E. grandis x E. urophylla.

Acid-catalysed xylose dehydration into furfural in the presence of kraft lignin.

Science.gov (United States)

Lamminpää, Kaisa; Ahola, Juha; Tanskanen, Juha

2015-02-01

In this study, the effects of kraft lignin (Indulin AT) on acid-catalysed xylose dehydration into furfural were studied in formic and sulphuric acids. The study was done using D-optimal design. Three variables in both acids were included in the design: time (20-80 min), temperature (160-180°C) and initial lignin concentration (0-20 g/l). The dependent variables were xylose conversion, furfural yield, furfural selectivity and pH change. The results showed that the xylose conversion and furfural yield decreased in sulphuric acid, while in formic acid the changes were minor. Additionally, it was showed that lignin has an acid-neutralising capacity, and the added lignin increased the pH of reactant solutions in both acids. The pH rise was considerably lower in formic acid than in sulphuric acid. However, the higher pH did not explain all the changes in conversion and yield, and thus lignin evidently inhibits the formation of furfural. Copyright © 2014 Elsevier Ltd. All rights reserved.

PCR-DGGE analysis of the microbial communities in three different Chinese "Baiyunbian" liquor fermentation starters.

Science.gov (United States)

Xiong, Xiaomao; Hu, Yuanliang; Yan, Nanfeng; Huang, Yingna; Peng, Nan; Liang, Yunxiang; Zhao, Shumiao

2014-08-01

A systematic investigation was performed on the bacterial, Bacillus, fungal, and yeast communities of the three types of Daqu (mechanically prepared, manually prepared, and mixed prepared) used in Baiyunbian Company by reconditioning PCR-denaturing gradient gel electrophoresis (PCR-DGGE). The DGGE results showed that the microbes in the three types of Daqu were mainly thermotolerant and thermophilic microbes, and the most dominant bacterial species were Bacillus and Virgibacillus, followed by Lactobacillus and Trichococcus. Furthermore, the dominant fungi were found to be molds, such as Rasamsonia, Penicillium, Aspergillus, and Monascus, and the dominant yeasts were Saccharomyces cerevisiae, Saccharomycopsis fibuligera, Pichia anomala, and Debaryomyces hansenii. In general, the three types of Daqu showed slight differences in microbial communities, and the Shannon indexes (H') of the manually prepared and mechanically prepared Daqu were similar. The results suggest that mechanically prepared Daqu can replace manually prepared Daqu in liquor production, and this research provides useful information for liquor production and process improvement.

Study on uranium loss during 'Iron-Gypsum Cake' precipitation from acid leach liquor of Jaduguda ore using factorially designed experiments

International Nuclear Information System (INIS)

Das, Amrita; Yadav, Manoj; Chatterjee, Ankur; Singh, A.K.; Hubli, R.C.

2012-01-01

Acid leaching process for uranium recovery from ore often generates considerable amounts of impurities into the solution. It is a challenge to separate the non-valuable impurities as manageable and stable waste products for final disposal, without losing the valuable constituents. The main impurities that come with the leach liquor are iron and sulfate. Their removal is essential for meeting the iron requirement in leaching circuit and also for making the effluent suitable for recycle. Factorial design analysis was applied to study of process variables for precipitation of iron and sulphate from leach liquor with composition using CaO as precipitation reagent

WITHDRAWN: Amnioinfusion for meconium-stained liquor in labour.

Science.gov (United States)

Hofmeyr, G Justus

2009-01-21

Amnioinfusion aims to prevent or relieve umbilical cord compression during labour by infusing a solution into the uterine cavity. It is also thought to dilute meconium when present in the amniotic fluid and so reduce the risk of meconium aspiration. However, it may be that the mechanism of effect is that it corrects oligohydramnios (reduced amniotic fluid), for which thick meconium staining is a marker. The objective of this review was to assess the effects of amnioinfusion for meconium-stained liquor on perinatal outcome. The Cochrane Pregnancy and Childbirth Group trials register (October 2001) and the Cochrane Controlled Trials Register (Issue 3, 2001) were searched. Randomised trials comparing amnioinfusion with no amnioinfusion for women in labour with moderate or thick meconium-staining of the amniotic fluid. Eligibility and trial quality were assessed by one reviewer. Twelve studies, most involving small numbers of participants, were included. Under standard perinatal surveillance, amnioinfusion was associated with a reduction in the following: heavy meconium staining of the liquor (relative risk 0.03, 95% confidence interval 0.01 to 0.15); variable fetal heart rate deceleration (relative risk 0.65, 95% confidence interval 0.49 to 0.88); and reduced caesarean section overall (relative risk 0.82, 95% confidence interval 0.69 to 1.97). No perinatal deaths were reported. Under limited perinatal surveillance, amnioinfusion was associated with a reduction in the following: meconium aspiration syndrome (relative risk 0.24, 95% confidence interval 0.12 to 0.48); neonatal hypoxic ischaemic encephalopathy (relative risk 0.07, 95% confidence interval 0.01 to 0.56) and neonatal ventilation or intensive care unit admission (relative risk 0.56, 95% confidence interval 0.39 to 0.79); there was a trend towards reduced perinatal mortality (relative risk 0.34, 95% confidence interval 0.11 to 1.06). Amnioinfusion is associated with improvements in perinatal outcome

Oil and gas activities in northern Norway; KonKraft rapport 6; Olje- og gassvirksomhet i nord

Energy Technology Data Exchange (ETDEWEB)

2009-07-01

KonKraft report 6 deals with oil and gas operations on the Norwegian continental shelf (NCS) from Nordland county and northwards. It aims to contribute to a broad factual base for decision processes related to opening new exploration areas in these waters. The Norwegian petroleum sector employs about 250 000 people directly and indirectly. It accounts for a third of government revenues, and 90 per cent of its profits accrue to the state. NOK 119 billion of the central government budget in 2009 comes directly from oil and gas revenues. These funds finance roads, nursery schools, hospitals and the Norwegian welfare state. In addition, they safeguard future pensions. This industry is at a crossroads today. Oil production has dropped by 30 per cent since 2000. Recent forecasts from the Norwegian Petroleum Directorate show that it may be reduced by 50 per cent from its peak by 2013. Overall oil and gas output is expected to begin falling from the middle of the next decade. To slow this decline in output and revenues, the oil companies need access to new and attractive exploration acreage. Half the production expected by the government in 2030 relates to resources which have yet to be proven. Opening further areas of the NCS to petroleum activities would contribute to maintaining substantial investment and revenues for the community, and to continuing the development of industry in the northernmost parts of the country. The report reviews unopened areas along the Norwegian coast from the Helgeland region and north-eastwards to the Russian border. Nordland VI and VII plus Troms II are regarded by the petroleum industry as the most promising regions for big discoveries which could slow the production decline. The KonKraft 2 report concerning production development on the NCS estimates remaining resources in these three areas at 3.4 billion barrels of oil equivalent (boe). (Author)

The denitration of simulated fast reactor highly active liquor waste

International Nuclear Information System (INIS)

Saum, C.J.; Ford, L.H.; Blatts, N.

1981-01-01

A short series of tests have been made with simulated HAL containing representative concentrations of palladium and phosphate ion. The information obtained has been confirmed in a small scale continuous denitration plant. These cases of four stirred pot reactors arranged in cascade. One possible advantage of this plant would be the low mean acidity in the first stage compared to the feed material which would limit to some extent the violence of the reaction. This would lead to a lower rate of gas evolution and may permit operation even with liquors where foaming is a problem. (DG)

Oxidizing attack process of uranium ore by a carbonated liquor