WorldWideScience

Sample records for koban shiyo kubun

  1. Required grades of hull steel plates in consideration of fracture toughness; Hakai jinsei wo koryoshita sentaiyo koban shiyo kubun ni kansuru ichikosatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yajima, H; Yamamoto, M; Ogaki, Y [Hiroshima University, Hiroshima (Japan). Faculty of Engineering

    1997-10-01

    This paper discusses the required grades of hull steel plates based on the steel ship rule of Nippon Kaiji Kyokai (NK). The minimum value of the allowable crack length in NK rule (critical safety crack length at 0degC just before brittle unstable crack causing fatal fracture) was estimated. In the case where the estimated crack tip exists in a matrix, the crack length was a minimum of 200-210mm, while nearly 60mm in a fusion line at high-heat-input welded joint. The allowable crack lengths estimated from a specified value in the NK rule were fairly different. The allowable crack length at 0degC was also estimated from the minimum value in V-notch Charpy impact test. The private proposal on the required grades of hull steel plates in consideration of fracture toughness was discussed. Thirty-five percent of crack lengths found in real ships is 100mm or less, however, cracks of 250-400mm long are frequently found suggesting the allowable crack length of 400mm. The required grade integrally considering required values and design conditions is demanded to secure the reliability of hull strength. 5 refs., 5 figs., 2 tabs.

  2. Development of high strength steel sheets for crashworthiness; Shototsu anzen`yo kokyodo usu koban no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Fukui, K; Yamamoto, M; Mizui, N; Hirose, Y; Kojima, K [Sumitomo Metal Industries, Ltd. Osaka (Japan)

    1997-10-01

    For frontal or rear members of automotive body, the most suitable high strength steel was investigated. Dynamic tensile test at strain-rate of 2000/s and crash test of hat-shape column at 4m/s were conducted for steel sheets with tensile strength ranging from 290 to 980 MPa. Dynamic tensile strength increases with increasing static one but the ratio of dynamic tensile strength to static one decreases. Tensile strength remarkably affects crash energy absorption of column and TRIP steel is superior to other steels with same tensile strength. 7 refs., 16 figs., 1 tab.

  3. Buckling model of longitudinal reinforcing bars under reverse cyclic load; Koban kurikaeshi kajuka ni okeru chukin no zakutsu model

    Energy Technology Data Exchange (ETDEWEB)

    Murayama, Y.; Suda, K.; Ichinomiya, T.; Shinbo, H. [Kajima Corp., Tokyo (Japan)

    1994-10-31

    For RC (reinforced concrete) columns such as towers of long-span cable-stayed bridges or high-rise piers, there is desired development of an analytical method including a method of arranging reinforcing bars for increasing their ductility against strong earthquake motion. For this, it is necessary to investigate their characteristics after their being rendered to maximum load and their final states, and hence there must be newly investigated the properties of a plastic hinge formed on the bottom of the column, particularly determination of the buckling point of reinforcing bars and a hysteresis model after the buckling. In this study, there is developed a direct method of measuring the stress of reinforcing bars embedded in a model specimen which is conventionally difficult to be measured, and there is investigated the stress-strain hysteresis of the bars before and after the buckling thereof. The principle of the method of measuring the stress is such that only a local minimum portion of objective reinforcing bars is rendered to rf quenching, and a distortion gauge is sticked to the center of the quenching. This is based upon a fact that that portion keeps a linear relationship between the stress and the strain even if a host material is yielded. On the basis of an experimental result, a mechanism of buckling of these bars is clarified and a buckling model of the reinforcing bars at the plastic hinge. 6 refs., 15 figs., 2 tabs.

  4. Development of TS590MPa grade high tensile strength steel for automotive anti-collision parts; Shogeki kyushuyo 590MPa kyu kochoryoku koban no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Miura, K; Takagi, S; Furukimi, O; Hira, T; Obara, T [Kawasaki Steel Corp., Tokyo (Japan); Tanimura, S [University of Osaka Prefecture, Osaka (Japan)

    1997-10-01

    The effects of strain rate on the deformation behavior of steels were investigated to find the most appropriate micro-structure of steel for anti-crash parts of automobiles, such as front-side-members. The dual phase steel absorbed a higher amount of energy during dynamic deformation than other steels with the same static yield strength. The increase of volume fraction of the austenite phase in the dual phase steel deteriorates the dynamic deformation behavior. The FEM analysis for crash test of HAT-sectional sheet box also showed the superior performance of the dual phase steel. 4 refs., 7 figs., 1 tab.

  5. Weight reduction of automobile parts using light metals. Keikinzoku shiyo ni yoru jidosha buhin no keiryoka

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, S [Toyota Motor Corp., Aichi (Japan)

    1992-12-25

    Weight reduction of automobiles is required from the viewpoint of reduction of CO2 emission and energy conservation. Comparing a car with another one of almost the same size and performance with 1% reduced weight, combustion efficiency of the latter can be improved by 0.5-0.8%. This report introduces several examples, in which steel parts are replaced with light alloy parts to reduce car weight, and describes the future perspective. Concerning a cylinder block which is the heaviest part among engine parts, a block made of aluminum alloy with no cast liner has been developed. There is also an example of an oil pan adopting aluminum die-cast for a part of it. A valve lifter made of aluminum alloy has been developed for valve system parts and has contributed to friction loss, noise reduction, and improvement of fuel consumption. As for steering system parts, a steering bracket made of Mg alloy die-cast has been developed. The use of light alloy parts, in general, increases material cost. Therefore it is now required to build up closer connection between designs and production techniques and to improve reliability of casting and forging technologies. 5 refs., 20 figs.

  6. International research on energy conservation techniques; Energy shiyo gorika shuho kokusai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    In order to utilize energy reasonably over the whole life cycle of products, the life cycle assessment (LCA) was researched including assessment of the quantity of environmental load. LCA is composed of the inventory analysis which analyzes objectively the amount of input and output of all substances and energy due to their gathering, mining, transport, production, use, recycling and scrapping, and the impact analysis to environment based on the inventory analysis. The inventory analysis of refrigerators was conducted. The unit amount of CO2 emission generated by production of materials was estimated on the basis of previous papers. In particular, CO2 emission due to overseas production of imported raw metals reached nearly 80% in Al and 70% in copper. Recycling of materials and heat recovery by combustion of waste were also considered. Environmental effect was next assessed using the inventory data in three stages of classification, characterization and valuation. Although the weight factor of environmental effect is necessary for every emission, European and American data are now used. 59 refs., 68 figs., 81 tabs.

  7. Standardized communication protocol for BAS (IEIEJ/p); BAS hyojun interface shiyo (IEIEJ/p)

    Energy Technology Data Exchange (ETDEWEB)

    Toyoda, T. [Hitachi Building System Co. Ltd., Tokyo (Japan)

    2000-10-05

    For the BEMS user, to construct his BEMS tinder the multiple vendors environment is very beneficial because he could choice the most appropriate vendor among many vendors about every subsystem for the view point of technique and cost at any time. The effective tool which makes the BEMS tinder the multiple environment possible is the BACnet protocol which had developed and been standardized by ANSI/ASHRAE of U.S.. Institute of Electrical Installation Engineers-of Japan (IEIEJ) offers IEIEJ/p based on BACnet as IEIEJ's standard which is added the function of autonomous decentralized control to enhance the BEMS reliability to fit the Japanese multiple vendors environment, In this paper I present the outline of it's specification and feature of IEIEJ/p. (author)

  8. 1998 Annual Study Report. Standardization of corrosion resistance testing/evaluation methods for coated steel sheets; 1998 nendo seika hokokusho. Hyomen shori koban no taishokusei shiken hyoka hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to develop the evaluation methods for reappearing corrosion characteristics of coated steel sheets in a short time, acid rain composition and artificial acid rain composition for the accelerated test were studied, and the cyclic corrosion tests were conducted. The literature survey shows that the main ionic species present in acid rain are Ca{sup 2+}, Mg{sup 2+}, Na{sup +}, K{sup +}, NH{sub 4}{sup +}, SO{sub 4}{sup 2-}, NO{sub 3}{sup -}, and Cl{sup -}, of which the acid rain components are SO{sub 4}{sup 2-} and NO{sub 3}{sup -}, their equivalent ratio (NO{sub 3}{sup -}/ SO{sub 4}{sup 2-}) in the Far Eastern area being 0.2 to 0.3. Therefore, the solution specified by ASTM 1141 is diluted 30 times with water to prepare the base solution for the accelerated tests, where its acidity is adjusted with a mixed acid of NO{sub 3}{sup -}/ SO{sub 4}{sup 2-} = 0.2 to 0.3 (pH: 3.0 to 4.0). Two sets of preliminary cyclic corrosion tests were conducted, one involving acid rain spraying, drying and humidification in this order, and the other acid rain spraying, humidification and drying. Analysis of the test data indicates that difference between these test cycles in corrosion rate is within a deviation range caused by different testing tools. Therefore, the former condition is adopted as the basis for the accelerated tests, because of its smaller deviation caused by different testing tools. (NEDO)

  9. Relationship between surface structure of silicon containing steel and adhesion of hot dip galvanized coating; Si gan'yu koban no hyomen kozo to yoyu aen mekki micchakuseino kankei

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiya, Y.; Hashimoto, S.; Ishibashi, Y. [Kokan Keisoku K.K., Kawasaki (Japan); Inagaki, J. [NKK Corp., Tokyo (Japan); Fukuda, Y. [Shuibuoka University, Shizuoka (Japan)

    2000-06-01

    The surface of the annealed steel and the exfoliated interface of the coating for the hot dip galvanized Si containing steel sheets was characterized by using SEM (Scanning Electron Microscope), AES (Auger Electron Spectroscopy) and TEM (Transmission Electron Microscopy). The adhesion of the coatings have depended on the Si content of the steel. It have been found that MnSiO{sub 3} particles are formed at the surface of the annealed steels having high Si content and that two types of grain having different distribution of the oxide exist in the steels. Large oxide particles have been formed in one type of grain and small particles are formed in the other type of grain. The different type of Fe-Zn alloy are formed on two types of grains. It have been observed that the oxide particles exist at the interface of exfoliated coatings after the adhesion test for the steels with high Si content. The distribution of the oxide particles observed at the bottom of the exfoliated coating is quite similar to that of the surface oxide of the annealed steel. From these results, the exfoliation of the coating has initiated at the oxide particles of the steel surface that has been not reduced during the hot dip galvanizing. (author)

  10. Corrosion resistance and protection mechanism of hot-dip Zn-Al-Mg alloy coated steel sheet under accelerated corrosion environment; Yoyu Zn-Al-Mg kei gokin mekki koban no sokushin fushoku kankyoka ni okeru taishokusei toi boshoku kiko

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, A.; Izutani, H.; Tsujimura, T.; Ando, A.; Kittaka, T. [NKK Corp., Tokyo (Japan)

    2000-08-01

    Corrosion behavior of hot-dip Zn-6%Al 0-3%Mg alloy coated steel sheets in cyclic corrosion test (CCT) has been investigated. The corrosion resistance was improved with increasing Mg content in the coating layer, and the highest corrosion resistance was observed at 3% Mg. In Zn-6%Al-3%Mg alloy coated steel sheet, the formations of zinc carbonate hydroxide and zinc oxide were suppressed for longer duration compared with Zn-0.2%Al and Zn-4.5%Al-0.l%Mg alloy coated steel sheets. As a result, zinc chloride hydroxide existed stable on the surface of the coating layer. From the polarization behaviors in 5% NaCl aqueous solution after CCT, it was found that the corrosion current density of Zn-6%At-3%Mg alloy coated steel sheet was much smaller than those of Zn-0.2%Al and Zn-4.5%Al-0.1%Mg alloy coated steel sheets. As zinc carbonate hydroxide and zinc oxide had poor adhesion to the coating layer and had porous structures, these corrosion products were considered to have little protective action for the coating layer. Therefore, it was concluded that Mg suppressed the formation of such nonprotective corrosion products. resulting in the remarkable improvement of corrosion resistance. (author)

  11. Fiscal 2000 survey report. Foundation building project for international energy use rationalization. Master plan preparation for rationalized energy use; 2000 nendo kokusai energy shiyo gorika kiso seibi jigyo chosa hokokusho. Goriteki energy shiyo no tame no master plan sakusei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For energy conservation and environmental protection using technologies for effective consumption of energy and for preventing pollution due to energy consumption, master plans were studied and prepared on photovoltaic power generation, wind power generation, natural gas utilization, and so on, for the Xinjiang Uygur Zizhiqu, Gansu Province, and Guandong Province, respectively. Propositions addressing the Xinjiang Uygur Zizhiqu involved a decrease in dependence on coal, utilization of natural gas, introduction of coal-fired cogeneration systems, introduction of wind power up to the level equivalent to the supply reserve capability, energy conversion and new industry development using natural gas, promotion of electrification of local communities, and so on. Propositions addressing Gansu Province involved the hydroelectric power system as the core of power sources, decrease in dependence on coal, enhanced utilization of natural gas, energy conversion and new industry development utilizing natural gas, and so on. Propositions addressing Guangdong Province involved a decrease in dependence on coal and oil, enhanced utilization of natural gas, introduction of natural gas-fired combined cycle power generation into urban sectors, accelerated utilization of wind power generation on isolated islands, and so on. (NEDO)

  12. Survey of the energy use rationalization freon decomposition technology (public use); Energy shiyo gorika freon bunkai gijutsu chosa. (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper made a research survey of a technology to decompose the recovered CFC (specified freon) in which energy efficiency is high and no hazardous materials such as dioxin are generated. As to the technology to decompose specified freon, the high frequency plasma method, the cement kiln method and the combustion method are at the stage of the demonstration test and close to the commercialization. The catalyst method has finished the basic test and is at the stage of a pilot plant. Besides, there are the supercritical water decomposition method, the ultraviolet decomposition method, etc., but they are at the stage of the fundamental research. Mechanisms of the dioxin generation and the suppression of dioxin generation in case of incinerating waste mixed with halide have been made clear. In the fundamental test, conditions were obtained under which the freon decomposition rate of more than 99.99% is attained by the combustion of a mixture of industrial waste and freon using the combustion method, and measures for reduction in hazardous materials such as dioxin were expected to be taken. In the catalyst method, the result obtained was the decomposition rate of more than 99.99% and the catalyst life of more than 1000 years, and its practicality was confirmed. 43 refs., 97 figs., 29 tabs.

  13. Canada continues use prohibition of gene recombination cattle somatotropin; Kanada wa idenshikumikaegyu seicho horumon no shiyo kinshi wo keizoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-04-05

    Canada continued use prohibition of gene recombination cattle somatotropin (BST) which stimulated milk increased production of this company in spite of request of Monsanto Co.. The cow that BST was administered is based on the report of veterinary surgeon that causes reproductive function and lowering in the life, dysbasia and increase in the mastitis on this. From the research report that BST causes thyroid gland cyst of the male rat in U.S.A., consumer organization and environment group petition FDA for the elimination of BST from the U.S.A. market. In the meantime, Monsanto Co. in the report which Canada adopted, chemical structure is different, and it reports that it uses BST of other company in which dosing method and dosing frequency differ and disregards the report of Cornell university in which the life of the cow administered more and more does not lower BST. (translated by NEDO)

  14. Survey on the international cooperation for resonable use techniques of energy; Energy shiyo gorika shuho kokusai kyoryoku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    LCA (life cycle assessment) is known as one of the techniques for assessing reasonable use of energy considering environment. Usefulness of LCA was examined by checking the consistency between the assessment result on refrigerators by LCA and ISO standards. LCA can digitize the data on energy substances, wastes and emission of the whole system. LCA is useful for effective use and control of resources, and to clarify the reduction chance of environmental impacts. However, the framework is necessary to estimate the accuracy of assessment technique for every category, and the reliability of influence assessment. Like a risk assessment for environmental damages, identification of discharge sources beyond the assessment function of potentials is difficult. As the viewpoint of the whole life cycle is important, assessment of local damages is difficult. The complementary use of LCA and other tools about sustainable development is important. The comparison result between ISO provisions and this LCA case study showed that this concrete research report can play a role as text book for the ISO technique. 74 refs., 38 figs., 45 tabs.

  15. Japan kynol: Activated carbon base fiber, use light pattern deodorant sale; Kassei tanso seni wo shiyo. Usugata no dasshuzai hanbai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-02-28

    The backbone manufacturer of the high function fiber, Japan kynol sells the deodorant (dassyu-irukakun) which used activated carbon fiber in late January. It is compared with grain-shaped activated carbon of the main stream with a deodorization material, and it is said that the space isn`t taken with a light pattern with a deodorization speed`s being early. It is sold in the center of the supermarket and the platform for a refrigerator and a locker, the pet house and the car. (translated by NEDO)

  16. Infectious Disease Risk and Vaccination in Northern Syria after 5 Years of Civil War: The MSF Experience

    Science.gov (United States)

    de Lima Pereira, Alan; Southgate, Rosamund; Ahmed, Hikmet; O’Connor, Penelope; Cramond, Vanessa; Lenglet, Annick

    2018-01-01

    Introduction: In 2015, following an influx of population into Kobanê in northern Syria, Médecins Sans Frontières (MSF) in collaboration with the Kobanê Health Administration (KHA) initiated primary healthcare activities. A vaccination coverage survey and vaccine-preventable disease (VPD) risk analysis were undertaken to clarify the VPD risk and vaccination needs. This was followed by a measles Supplementary Immunization Activity (SIA). We describe the methods and results used for this prioritisation activity around vaccination in Kobanê in 2015. Methods: We implemented a pre-SIA survey in 135 randomly-selected households in Kobanê using a vaccination history questionnaire for all children Syria. The VPD Risk Analysis prioritised measles, Haemophilus Influenza type B (Hib) and Pneumococcus vaccinations. In the measles SIA, 3410 children aged 6-59 months were vaccinated. The use of multiple small vaccination sites to reduce risks associated with crowds in this active conflict setting was noted as a lesson learnt. The post-SIA survey estimated 82% (95%CI: 76.9-85.9%; n=229/280) measles vaccination coverage in children 6-59 months. Discussion: As a result of the conflict in Syria, the progressive collapse of the health care system in Kobanê has resulted in low vaccine coverage rates, particularly in younger age groups. The repeated displacements of the population, attacks on health institutions and exodus of healthcare workers, challenge the resumption of routine immunization in this conflict setting and limit the use of SIAs to ensure sustainable immunity to VPDs. We have shown that the risk for several VPDs in Kobanê remains high. Conclusion: We call on all health actors and the international community to work towards re-establishment of routine immunisation activities as a priority to ensure that children who have had no access to vaccination in the last five years are adequately protected for VPDs as soon as possible. PMID:29511602

  17. Infectious Disease Risk and Vaccination in Northern Syria after 5 Years of Civil War: The MSF Experience.

    Science.gov (United States)

    de Lima Pereira, Alan; Southgate, Rosamund; Ahmed, Hikmet; O'Connor, Penelope; Cramond, Vanessa; Lenglet, Annick

    2018-02-02

    In 2015, following an influx of population into Kobanê in northern Syria, Médecins Sans Frontières (MSF) in collaboration with the Kobanê Health Administration (KHA) initiated primary healthcare activities. A vaccination coverage survey and vaccine-preventable disease (VPD) risk analysis were undertaken to clarify the VPD risk and vaccination needs. This was followed by a measles Supplementary Immunization Activity (SIA). We describe the methods and results used for this prioritisation activity around vaccination in Kobanê in 2015. We implemented a pre-SIA survey in 135 randomly-selected households in Kobanê using a vaccination history questionnaire for all children Syria. The VPD Risk Analysis prioritised measles, Haemophilus Influenza type B (Hib) and Pneumococcus vaccinations. In the measles SIA, 3410 children aged 6-59 months were vaccinated. The use of multiple small vaccination sites to reduce risks associated with crowds in this active conflict setting was noted as a lesson learnt. The post-SIA survey estimated 82% (95%CI: 76.9-85.9%; n=229/280) measles vaccination coverage in children 6-59 months. As a result of the conflict in Syria, the progressive collapse of the health care system in Kobanê has resulted in low vaccine coverage rates, particularly in younger age groups. The repeated displacements of the population, attacks on health institutions and exodus of healthcare workers, challenge the resumption of routine immunization in this conflict setting and limit the use of SIAs to ensure sustainable immunity to VPDs. We have shown that the risk for several VPDs in Kobanê remains high. We call on all health actors and the international community to work towards re-establishment of routine immunisation activities as a priority to ensure that children who have had no access to vaccination in the last five years are adequately protected for VPDs as soon as possible.

  18. Fiscal 1997 survey report on international cooperation for the energy use rationalization method; 1997 nendo jigyo hokokusho (energy shiyo gorika shuho kokusai kyoryoku chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To carry out LCA in ISO-14040, inventory analysis (IA) is the basic. For studying arrangement of public data to carry out IA, collection work was done of background data which are indirectly concerned with copying machine. First, methods to make inventory data (ID) which are thinkable in the present situation were prepared, and items of emitted matters to be collected were set up in relation to the impact assessment method. Secondly, scenarios of each stage of life cycle of copying machine were set up, and virtual data on the material/energy consumption amount were arranged. Based on this, a method was further studied for making ID of the parts used in electric power, iron/steel, plastics, and copying machine. Third, based on the above-mentioned study results, ID was actually made, and a possibility was studied of making inventory in life cycle of copying machine. Moreover, the state of the automobile LCA carried out at Stuttgart University was examined. At last, the paper summed up subjects of and future study methods for the inventory making method. 2 refs., 25 figs., 77 tabs.

  19. Report on a survey in fiscal 1999. Survey on energy use evaluation systems; 1999 nendo energy shiyo hyoka system chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The present survey and study relate to the medium to long term policies for technological development of energy and environment related technologies, and are intended to develop a system that can evaluate the importance, feasibility, expected realization time, and expected cost of the technologies, including their synergetic effects. The survey and study are intended to provide clear guidelines for planning the technological development policies on which of the technological development should be promoted in what ways, based on the evaluation given by the use of the system. The report describes in Section 1 to adopt two types of approaches of a 'technology map' and a 'network chart evaluation system' to achieve the goal. Section 2, after describing the results of surveys on the past study cases of technology evaluation, describes that the present approach has new features that are different from conventional ones. Section 3 states the results of surveys on the basic technologies to prevent global warming, and shows cases of preparing maps that notice on energy flows. Section 4 relates to network chart evaluating methods. Section 5 describes the results of surveys that have been made in relation with chronological progress of the technological development, in preparation for surveys to be made in the coming fiscal years. (NEDO)

  20. Fiscal 1999 survey report. Survey of international cooperation over energy use rationalization techniques; 1999 nendo energy shiyo gorika shuho kokusai kyoryoku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the past, studies have been conducted involving the possibility of development of information offering techniques for the realization of sustainable society, for which LCA (life cycle assessment) as a tool for reducing energy consumption and environmental impact is investigated and case studies are conducted in this connection. In this fiscal year, for the purpose of deliberating how to utilize the LCA results, a survey is conducted of how LCA is being used as a tool for constructing an environmental management system set forth in the ISO14000 series, by holding conferences with LCA researchers representing the respective countries involved. Investigations are conducted into the actualities of the environmental management system, environmental performance assessment, and environmental labelling whose standardization has been under way in compliance with the ISO14000 series, into the actualities of matters relating to assessment techniques and decision making such as environmentally-friendly designing, supply chain management, reports on environments, etc., which are becoming established in enterprises, and into the actualities of access to and disclosure of information. International cooperative researches are conducted, participated in by five leading organizations of Sweden, Germany, Denmark, and Canada, and Japan's National Institute for Resources and Development, where actual states of LCA utilization are introduced and improvement on LCA techniques are discussed. (NEDO)

  1. Fiscal 1998 research report on the international cooperation for techniques of rational energy use; 1998 nendo energy shiyo gorika shuho kokusai kyoryoku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For promotion of the implementation of LCA, 'Japan-Europe joint project for LCA (life cycle assessment) of photocopiers' was established. The following organizations were selected for this project; Material Research Institute of the Swiss Confederation (EMPA), PE Engineering (PE) consortium and Stuttgart University (IKP) of Germany, Leiden University of the Netherlands (CML), and Pre Consultant of the Netherlands as the European coordinator of the project. The project includes the following as issues: The estimation method of material composition/production process data from parts names, practical data items (kind of materials, inventory data) used by European institutes, the guidance for construction of Japanese LCA database, and the viewpoint of inventory accuracy. The following are also reported: the limitation of possible impact assessment based on current inventory analysis data, the viewpoint on the time dependence and regional one of impact assessment, and the viewpoint on integration of impact assessment. (NEDO)

  2. Effect of applied synthetic auxin on root growth in plantlet propagation by cuttage and tissue culture; Sashiki to soshiki baiyo ni okeru gosei auxin rui no shiyo koka

    Energy Technology Data Exchange (ETDEWEB)

    Shoji, K; Yoshihara, T [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1996-12-01

    The effect of synthetic plant hormone 4-C1-IAA and TFIBA on root growth in plantlet propagation was clarified by the cuttage and the issue culture of strawberry seedling production. A periwinkle, vine, and azalea are the effect of 4-C1-IAA on root growth, and a promotion effect was recognized for rooting and root elongation. The concentration of 4-C1-IAA in which the growth promotion effect of a root most appears varies depending on the species of a plant. The concentration of a periwinkle was 20 ppm, and that of an azalea was 2000 ppm. The growth promotion effect of a root in 4-C1-IAA and TFIBA was compared with IBA for an azalea. The result showed that 4-C1-IAA is the same in the effect as IBA and that TFIBA is higher than for IBA. The growth of a vine`s terminal bud was promoted by the effect of TFIBA on root growth, and the callus occurring when IBA was treated was not formed. The rooting of a strawberry was promoted by the effect of TFIBA on root growth. The combined use of TFIBA and BA promotes the growth of a side bud and forms a multi-bud plant. However, rooting was inhibited. The callus caused by the effect of BA on root growth could be suppressed through the combined use with TFIBA. 6 refs., 7 figs., 2 tabs.

  3. Changes in soil organisms by the application of sludge composits, and their effects. Odei taihirui no shiyo ni tomonau dojo seibutsu no henka to sono eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Niijima, K.; Fujita, K.; Ogawa, M. (Forestry and Forest Products Research Institute, Tsukuba (Japan))

    1993-08-31

    With an objective to utilize sewage sludge more effectively, composted sewage sludge has been applied to seed beds to investigate its effect on soil macrofauna and higher fungi, and its relativity with change in soil organisms, growth of young trees, and soil science. Forty-eight seedling sections, each 5 m [times] 5 m, were made on a seed bed which was applied with Tenryu sludge composts (polymer-based coagulant), several other kinds of sludge composts, fallen leaf composts, and cattle excrement composts at predetermined rates from zero to 20 kg. Each section was planted with 25 three-year-old nursery trees of a kind of oak, black pine, and cypress. As a result, the following findings were obtained: wet weight of larvae of Japanese gold beetles that attack tree roots has increased during the first and second years in the Tenryu sludge applied section, but no longer increased in the third year; the relationship between the other composts and soil macrofauna was not made clear; Scleroderma Cepa PERS, a mycorrhiza bacteria, has been generated in the oak planted section in the second, third and fourth years, with the second year particularly having generated it in a greater amount in proportion with the fertilizer application amount, but the fertilizer effect thereafter is not clear. 24 refs., 6 figs., 9 tabs.

  4. Fiscal 1999 survey report. Survey of international cooperation over energy use rationalization techniques; 1999 nendo energy shiyo gorika shuho kokusai kyoryoku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the past, studies have been conducted involving the possibility of development of information offering techniques for the realization of sustainable society, for which LCA (life cycle assessment) as a tool for reducing energy consumption and environmental impact is investigated and case studies are conducted in this connection. In this fiscal year, for the purpose of deliberating how to utilize the LCA results, a survey is conducted of how LCA is being used as a tool for constructing an environmental management system set forth in the ISO14000 series, by holding conferences with LCA researchers representing the respective countries involved. Investigations are conducted into the actualities of the environmental management system, environmental performance assessment, and environmental labelling whose standardization has been under way in compliance with the ISO14000 series, into the actualities of matters relating to assessment techniques and decision making such as environmentally-friendly designing, supply chain management, reports on environments, etc., which are becoming established in enterprises, and into the actualities of access to and disclosure of information. International cooperative researches are conducted, participated in by five leading organizations of Sweden, Germany, Denmark, and Canada, and Japan's National Institute for Resources and Development, where actual states of LCA utilization are introduced and improvement on LCA techniques are discussed. (NEDO)

  5. Disinfectants used in medal field and problems caused from their use. Igaku ryoiki ni okeru sakkinzai to sorera shiyo ni yoru mondaiten

    Energy Technology Data Exchange (ETDEWEB)

    Okuda, K; Watabe, S [Yokohama City University, Yokohama (Japan). School of Medicine

    1994-04-05

    This paper describes typical anti-microorganism chemicals used in hospitals, and touches on measures against intra-hospital infection. Killing microorganisms reliably by using a high-pressure steam sterilization method is the best means for medical devices and apparatuses. However, there are high-priced medical devices that cannot withstand such a method and require other processes according to the situations, such as gas sterilization and alcohol disinfection. In addition to such sterilization methods as using heat, alcohols, and gases, methods that have been developed recently may include the following: use of Bronopol (an antiseptic) and anti-mold agents that have electronphilic functional groups, disinfectants using metal ions from silver, zinc and copper, and other materials. The problem of intra-hospital infection is caused typically by MRSA, hepatitis virus and Pseudomonas aeruginosa. Preventive measures require good knowledge about their infection courses and disinfecting technologies, as well as an attention not to cause change in the ecology as a result of using excessively strong chemicals. 18 refs., 1 fig., 1 tab.

  6. Effects of cellular telephone manipulation on driver`s performance; Jidosha untenchu no keitai denwa shiyo sosa ni kanrensuru mondai no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tokunaga, R; Ozawa, M; Hagiwara, T [Hokkaido University, Sapporo (Japan); Takagi, H; Shimojo, A [Civil Engineering Research Institute of Hokkaido, Hokkaido (Japan)

    1997-10-01

    The present evaluates effects of cellular telephone manipulation on driver`s performance. The major independent variables were the reaction time and the mental workload. Hart et al. proposed the concept of the subjective mental workload. Experiments were conduced using a driving simulator without motion. Findings showed that the hands free system may provide less effect than the cellular telephone on the passenger seat on driver`s reaction time and mental workload. 4 refs., 2 tabs., 5 figs.

  7. Fiscal 2000 report of investigation. International cooperative investigation on method for rationalizing use of energy; 2000 nendo energy shiyo gorika shuho kokusai kyoryoku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigative research was conducted for the purpose of building a database for LCA (life cycle assessment) that will be commonly used in Asian countries and developing an applicable environmental assessment methodology, with the fiscal 2000 results compiled. This year, joint researches and investigations were carried out with four countries, namely, Konkuk University (Korea), Taiwan Environmental Management Association (Taiwan), Universiti Putra Malaysia (Malaysia), and Thailand Environmental Institute (Thailand). The investigation covered the status how LCA problems were dealt with and how LCA infrastructures were built in the four countries. In the construction of the database for LCA, methods of preparing the LCA inventory database and their results were investigated concerning electrical power systems and production of basic materials (steel products), which were most important in implementing LCA in particular. In Thailand and Malaysia, lack of data for LCA was presumed; hence, necessary data sources were examined. Further, investigated also were the state of importing subterranean resources such as coal, oil, natural gas and iron ore, and the resource material flow or the like in each country. (NEDO)

  8. Fiscal 1980 Sunshine Project research report. Development of slurry applicable to geothermal environment; 1980 nendo chinetsu kankyoka de shiyo kanona deisui no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    This report summarizes the fiscal 1980 research result on development of slurry applicable to geothermal environment. Study was made on the hydrothermal alteration and rheology of the clay suspension slurry system composed of base mud of sepiolite (thermogel), dehydrator of sodium polyacrylate (SPA), and dispersant GT-8. The study result clarified roughly the action mechanism of such slurry under geothermal environment. Such slurry thus achieved an expected target experimentally through various tests on slurry characteristics at higher temperature, slurry curing and slurry conditioning. Test was made on the lubricity of air system drilling fluid. Simulated field test was made on a preventive effect from lost circulation by using combination of various materials. The preventive effect increased with the kind of additional preventive agents. As for waste sludge treatment technology, the agitating capacity of a mixing tank for polymer flocculant was improved. Study was made on possible continuous treatment of sludge by using the above equipment and a continuous sludge caking equipment, resulting in achievement of an expected target. (NEDO)

  9. Byen prisme

    DEFF Research Database (Denmark)

    Breitenbauch, Henrik Ø.; Winther, Mark; Jakobsen, Mikkel Broen

    Aleppo, Mosul, Kobane, Palmyra, Fallujah, Raqqa og Ramadi. Listen over byer, hvor der kæmpes eller er blevet kæmpet i Irak og Syrien, er lang. Kampen mod ISIL og den syriske borgerkrig er væsentlige eksempler på, at krigen og byerne i stigende grad er sammenhængende temaer. Verdens befolkningstal...

  10. Fiscal 1997 report on the results on the international standardization R and D. Development of chemical methods to analyze/evaluate metallic coatings of surface treated steel coating sheets; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Hyomen shori koban mekkiso no kagaku bunseki hyoka hoho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper studied the international standardization of the chemical analysis method and glow discharge optical emission spectrometry. Chemical composition and coating thickness (g/m{sup 2}) of 14 kinds of specimens including alloy coatings and organic coating with zinc and aluminum as base were analyzed by the above-mentioned methods to examine the relation between the both. As the chemical analysis method, used was inductively coupled plasma atomic emission spectrometry. To study the relation between the methods, it was found to be necessary to recognize morphology at the boundary between the coating and base steel using, for example, scanning electron microscope (SEM) and electro-probe micro-analysis (EPMA). To measure traceability of the analysis method, with the chemical analysis method as a judgement method, it is necessary to make reference materials by coating materials, to use the calibration graph confirmed by the materials and to adopt the glow discharge optical emission spectrometry. On the basis of such way of thinking, drafts were worked out for the international standardization of the chemical analysis method and glow discharge optical emission spectrometry. 7 refs., 117 figs., 33 tabs.

  11. Fiscal 2000 report on result of development project of marine resources utilization system for energy conservation. Development of marine resources utilization system for energy conservation (Model demonstrative research and basic study); 2000 nendo energy shiyo gorika kaiyo shigen katsuyo system kaihatsu jigyo seika hokokusho. Energy shiyo gorika kaiyo shigen katsuyo system kaihatsu (model jissho kenkyu oyobi kiban kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This paper explains the development of marine resources utilization system for energy conservation. The conceptual system is designed to take a large amount of deep sea water of 100 thousand to 1 million tons a day, to utilize it from the viewpoint of energy conservation using its coldness and purity characteristics, to then discharge it to the area of the sea in minimizing the environmental effect as well as obtaining effect such as absorption of carbon dioxide gas through cultivation of phyto-plankton. In pump-up technology, a piping system attaching on sea bed or floating with one or multiple constraints is applicable at present to all sites of geographical and oceanographic conditions. In utilization technology, use of deep-sea water as cooling water at a steam power plant, for example, improves generation efficiency by one point or more. In discharge and environment-related technologies, the research revealed that the deep-sea water from 300 m below releases carbon dioxide gas at surface, while photosynthesis can absorb the gas in the process of using nutrition contained in the deep-sea water; therefore, comprehensive examination is necessary taking energy utilization effect into account. Candidate sites were selected in areas of 200 m depth and within 5 km off-shore, with the optimum system examined at each site. (NEDO)

  12. Fiscal 2000 survey report on rationalization project for international energy conservation. Preparation of master plan for rational energy consumption (Shanxi Province, China); 2000 nendo kokuasi energy shiyo gorika kiban seibi jigyo chosa hokokusho. Goriteki energy shiyo no tame no master plan sakusei (Chugoku Shanxi sho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A comprehensive master plan for Shanxi Province was prepared jointly with China for the purpose of promoting rational use of energy and realizing an environmentally harmonious demand/supply structure of energy. This paper describes the fiscal 2000 results. The first phase refers to the surmounting of environmental problems incident to the use of coal and the restoration of regional economy. As countermeasures against air pollution in Taiyuan City, environmental measures were propagated such as simplified flue-gas desulfurization in thermal power plants, energy conservation in coke dry quenching, etc., and desulfurization of coke oven gas. Bio-briquette effective against smoke and soot pollution was carried out, as was general rubbish treatment (e.g., compost and coal/rubbish mixed combustion power generation). Promoted, by the opening of a clean coal center, were sulfur content reduction, coal briquette method, market expansion for CWM, etc. Producing city gas out of coal mine methane gas was also among the ideas considered. With the aim of attaining a Shanxi Province zero emission program, incentives are essential and, for this purpose, support by the national government is desirable including subsidies for investment, low-interest loans, tax deductions/exemptions, and yen-denominated loans from Japan. The second phase is intended for harmony with culture/science/nature, control of global warming and advanced utilization of coal. (NEDO)

  13. FY 1999 survey report on the survey of destruction technology of HFC, etc. for rationalization of energy use. Survey of the actual state of use/recovery/emissions of HFC, etc.; 1999 nendo energy shiyo gorika HFC nado hakai shori gijutsu chosa hokokusho. HFC nado shiyo kaishu haishutsu jittai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey was aimed at collecting the basic data for studying a possibility of conversion of the recovery system of refrigerant freons, mostly DFC, into HFC, etc., which has been proceeded with in Japan. Of HFCs, PFCs and SF{sub 6} used for survey, only SF{sub 6} is now being recovered and processed. As to HFCs, HFC-134a was arranged, and the recovery/destruction to meet users' handling methods are requested because of the diverse usage and users. The points of the control of emissions of chemical substances into the atmosphere are the decrease in number of times of transport/filling-up at the time of materials handling and the closed system in plants and installation. If considering the heightening of efficiency of materials flow, requested are the decrease in number of times of transport/filling-up, the increase in quantity received by users, and measures to be taken for leakage at the time of receiving. In relation to the conversion of the recovery system of refrigerant freons, mainly CFC, into HFC, etc., all the industries concerned with the generation of the used substances to the materials flow have to promote the technical development for the structure and recovery in cooperation with each other. (NEDO)

  14. Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

  15. Study on construction of temporary dwellings and problems caused by living long time on Hanshin-Awaji Great Earthquake; Hanshin / Awaji daishinsai ni okeru okyu kasetsu jutaku no secchi to chokikan shiyo suru baai no kadai ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, K.; Nakamura, Y. [Nagasaki Univ. (Japan)] Shimizu, Y. [Kumagai Gumi Co. Ltd., Tokyo (Japan)

    1998-10-20

    Two years after the above-titled earthquake, an examination was performed on inhabitants in the temporary dwelling houses in Kobe, center of the calamity, and problems caused by a long stay there were clarified together with a grasp of the evolving problems by comparing the result of survey carried out immediately after the disaster. The number of such temporary dwelling houses amounted to 29,128 within Kobe City and 3,168 outside of the city. According to the room arrangement, they were either one f 4 types : 2-rooms with a kitchen, 1 room with a kitchen, dormitory and those specifically for aged persons. There were 59,449 applications at the first offer of 2,702 houses. The priority of their assignments and so on are explained. As for the housing structure, numerous complaints concerned with the room temperature, noise and so forth. As for the living environment, lack of nearby commodity shop, omission of transportation access, ill drainage of the housing sites were pointed out and the matters of demand to the local authorities included the installation of mail post and street lights. As for the health management, insomnia, stiff shoulder, lumbago and other bad physical conditions were revealed. The financial difficulty and the high house rent were obstacles to migrate to other places. The prolonged temporary lives worsened the apprehension of dwellers for the earthquake, typhoon, fire and alike. Some features for the calamity are described in comparison with the result of survey on those who were compelled to live under similar conditions by the eruption of Mr. Fugen. 6 refs., 13 figs., 15 tabs.

  16. Fiscal 2000 report on result of R and D on robot system cooperating and coexisting with human beings. Development of energy conservation technology; 2000 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    Introduction of a number of robots and consumption of a large amount of energy are unavoidable if a complicated process operation is to be carried out by robots in an extensive work site. Great energy conservation is contrived by developing robots applicable to manufacturing in performing a variety of operations in place of human beings and thereby reducing the number of robots to work. This paper explains the fiscal 2000 results. For dual-handed cooperative tasks, a function was examined capable of gripping an object without giving a humanoid robot an instruction of an exact gripping position. A method was designed to prepare a command for the other arm through a command for one arm, with torque impedance control employed for the purpose of avoiding damage due to collision. A study was conducted on a three-dimensional shape detecting model using a visual device of a robot. In grasping problems of balance control of a humanoid robot, the behavior of a robot consisting of multi-links was considered as behavior of inverted pendulum, with possibility checked for the stabilization of the balance. For the purpose of putting the virtual robot platform previously developed to practical use, a three-dimensional operation tool of run-time user interface was developed, with research conducted on the sophistication of robot application. (NEDO)

  17. Survey of the development of an energy use rationalization home welfare apparatus system. Report on results of the research under consignment; 1996 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa itaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper analyzed characteristics of structures of houses considered of aged people, characteristics of use of home welfare apparatus, etc. and investigated/studied energy effective use type home welfare apparatus systems. As to the energy assessment of home welfare apparatus, measurement/evaluation of the energy consumption were conducted in the state of the use according to shapes of life/action of aged people/people needing care in terms of electric-driven bed, care lift, electric-driven wheel chair, etc. Concerning the assessment on energy demand in houses considered of aged people in accordance with regional characteristics, three welfare technohouses were used. In Sapporo, Hokkaido, conducted were evaluation of the present situation of indoor environment and the energy demand, the snow disposal problem at the approach and the energy demand assessment on road heating, etc. In Kamogawa, Chiba prefecture, a research study was made of factors of the increasing energy consumption caused by the use of care apparatus. In Shiga prefecture, an analytical study was carried out of biological effects of the thermal environment in home care houses on aged people, etc. 21 refs., 341 figs., 70 tabs.

  18. Achievement report for fiscal 1998. Research and development of synergy ceramics (Development of technology for energy use rationalization); 1998 nendo seika hokokusho. Shinaji ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim is to create inorganic materials with their functions well harmonized and with their reliability remarkably improved, and efforts are made to establish basic technologies with which structural control may be carried out simultaneously for multiple layers in in-process products through positive utilization of various chemical reactions in the materials synthesizing process. This fiscal year's achievements are stated below. A low-temperature pressure nitriding method is developed in which nitriding reaction directly involves the metal aluminum compact for conversion into ceramics, and an aluminum sintered body is produced capable of high thermal conduction of not less than 170w/mk with the original compact shape retained. By a heat treatment in a high-temperature pressure nitriding atmosphere, a success is attained in producing a silicon nitride ceramic body enhanced (150w/mk) in thermal conduction. It is clarified that the microwave-aided selective heating technology works effectively in enhancing the particle growth rate in a liquid-phase sinter system, and a success is won in increasing strength by virtue of the formation of particle-growing particles. (NEDO)

  19. FY 1999 report on the results of the R and D of the plant use energy utilization rationalization industrial material production technology; 1999 nendo shokubutsu riyo energy shiyo gorika kogyo genryo seisan gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of using plants to the process to produce energy conservation type/environmentally friendly type industrial materials, the R and D were conducted on the improvement in material productivity/stress resistance of plants by transgenetic technology, etc., and the FY 1999 results were summarized. In the study of the creation of plants to produce industrial materials by genetic recombination of eucalyptus trees, it was found out that early maturing branches of eucalyptus trees were a material suitable for Agrobacterium infection, and conditions to efficiently acquire transformation calluses were obtained. In the R and D of the creation of soybeans to produce polyunsaturated fatty acid, a gene of unsaturated enzyme was acquired from Mortierella alpina storing ultra-long chain polyunsaturated fatty acid, and an experimental study was made to study whether or not this gene functions by plant. Further, studies were conducted on the technology to produce hybrid fiber by salt tolerance plants, creation of plants to produce isoprenoid/natural rubber, technology to produce tissue-specific high proteins, study on the molecular breeding of disease resistant plants, etc. (NEDO)

  20. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Sapporo City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Sapporo) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Daily, weekly and annual changes in energy use at care-taking sites were studied with the following six assignments enumerated: (1) studies on energy use amount in residential houses in the Hokkaido district, (2) discussions on improving energy conservation and efficiency in electric room heating systems and road heating, (3) evaluation on indoor air environment and discussions on effectiveness of air cleaning devices and ventilation systems, (4) surveys and studies on rational snow disposal methods for houses for physically handicapped and elderly persons and on housing patterns, and (6) surveys on effects of room warming environment in energy saving type houses on body feeling of elderly persons. Development of at-home welfare device systems utilizing energy more effectively was studied with the following five assignments enumerated: (1) surveys on energy consumption evaluation of at-home welfare devices, (2) surveys on developing a method to simulate energy consumption by analyzing utilization of the at-home welfare devices, (3) surveys on energy consumption and pleasantness associated with movement from a living section using the welfare devices to outdoor, (4) surveys on a garage utilizing a home elevator and around the garage, and (5) surveys on temperature setting and energy consumption when humidity in the garage is adjusted. (NEDO)

  1. Report on the joint research on the technology development of energy use reduction gas diffusion electrode salt electrolysis; Kyodo kenkyu energy shiyo gorika gas kakusan denkyoku shokuen denkai gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of energy conservation in the 'soda industry' which is an energy multi-consumption industry, study was made of the commercialization applying 'gas diffusion electrode' which is used for fuel cells, and the FY 2000 results were summed up. As to the development of production technology of gas diffusion electrode, conditional studies were conducted of the material production process, grinding process, mixing machine, filling, coating process, hot press process, etc. Concerning the evaluation of durability of the gas diffusion electrode, analysis of long-term operation electrode was conducted, and a lot of information on the degradation mechanism was obtained. In the degraded electrode, wetting of gas diffusion layer is going on, which is thought to directly cause the degradation. It is supposed that between the stable electrode and the degraded electrode, there are no changes in diameter of carbon powder and there is no carbon consumption. As to the verification test using the practical scale electrolytic cell, a trial operation started in February 2001. About the electrolytic performance, the electrolytic voltage is appropriately 2.2V, keeping the stable numerical value. The comparatively favorable performance is being maintained. (NEDO)

  2. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Ube City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Ube) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The present study utilizes a Welfare Techno-House to analyze structural characteristics of residential houses arranged with considerations for elderly people, and operation characteristics of at-home welfare devices. It is also intended to identify the status of energy consumption, and research and develop energy saving devices. The research and development items for the current fiscal year are as follows: (1) survey on power consumption in at-home welfare devices, and (2) development of at-home welfare device systems utilizing energy more effectively - sub-item a.: studies on leveling of energy use, b.: studies on identification of load applied to riders of power driven wheelchairs when they are operated, c.: studies on next generation housing for elderly and physically handicapped people, d.: surveys on discharged VOC concentration in houses built in warm districts. In item (1), power consumption of air conditioners for room heating in winter was measured to have derived time series data of daily change in the energy consumption. In the sub-item a, discussions were given on system efficiency evaluation on ice heat storing devices and floor cooling devices, and the indoor thermal environment characteristics. In the sub-item b, load applied to riders of power driven wheelchairs when they are operated was experimented for verification. In the sub-item c, surveys were performed on hot heat environment in a greenhouse attached to a residential houses arranged with considerations for elderly people. In the sub-item d, measurements were carried out on formaldehyde concentration and VOC in houses newly built in warm and cold districts to discuss preventive measures for indoor air pollution. (NEDO)

  3. FY 1999 report on the investigational study of the actual state of the utilization of clean energy vehicles for the transport business use; 1999 nendo chosa hokokusho. Unso jigyo yo clean energy jidosha no shiyo jittai ni kakawaru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of promoting the utilization of clean energy vehicles (CEV), survey was made on the assessment of the pollution by the CEVs introduced by now, subjects on the utilization, etc. As to the transport business use CEV running in the market, CNG vehicle is mostly used, and therefore, the gas emitted from them was tested. As a result, it was found out that CNG vehicle emits fewer NOx, PM and soot/smoke than diesel cars and contributes to improving the air pollution in large cities. However, it emits more CO2 than diesel car, and accordingly, it is necessary to reduce the fuel consumption. The practicality in the limited running distance is almost the same as that of diesel car, but it is desirable to improve startability, acceleration and gradability. Further, the occurrence of any troubles was pointed out in a third of the total numbers of CEV vehicle. Improvement in reliability is a must. CEV is higher in car cost than diesel car, and for the spread/promotion, it is necessary to prepare for assistance such as subsidy. Moreover, there are many requests for improvement in number, business hours, supply capacity, etc. of fuel supply station. (NEDO)

  4. FY 1974 Report on results of Sunshine Project. Research and development of cement serviceable under geothermal conditions; 1974 nendo chinetsu kankyoka de shiyo kanona cement kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-30

    Researches are conducted for the (research and development of cement serviceable under geothermal conditions). The research items include (1) surveys on test apparatuses, (2) basic surveys on cement, additives and cement slurry, (3) R and D of cement, and (4) researches on cement additives and slurry. For the item (1), bright prospects are obtained that US's Chandler can supply a thickening time tester serviceable at up to 750 degrees F and 40,000 psi, and a cement curing device serviceable at up to 750 degrees F and 5,000 psi. For the item (2), the surveys are conducted on the existing techniques for curing reactions and chemical resistance of cement at elevated temperature and pressure. For the item (3), the researches are conducted to develop cement resistant to heat and sulfates for geothermal development purposes, where portland cement and mixed portland cement are used as the bases which are incorporated with silica powder. As a result, it is found that the optimum Ca/SiO{sub 2} and CaO/SiO{sub 2}+Al{sub 2}O{sub 3} molar ratios are around 1.0 to 0.9 and 0.9 to 0.8, respectively. For the item (4), the tests are conducted to determine adequate conditions of conductor pipe cementing and cement slurry for 1,500m deep geothermal wells, and the standard composition is established. (NEDO)

  5. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Chofu City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Chofu) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes investigative studies on a new at-home welfare devices. Section 2 of the document, 'Studies on electric power conservation considering living patterns of elderly and physically handicapped persons' describes verification experiments in ferro-concrete buildings and ordinary homes by using a prototype system structured in last fiscal year. Qualitative analysis was performed based on the result thereof. In the 'Surveys on working environments for elderly people', directionality was presented in improving labor environments for the elderly people. Section 3, 'Studies on emergency evacuation devices for physically handicapped and elderly people' discovered that many of the presently available evacuation devices are intended of use mainly by handicap-free people, and there are many aspects that are difficult to say that elderly and physically handicapped people are included in the field of vision. In the 'Studies on an at-home training supporting system to maintain movement functions of the legs of elderly people', design and fabrication were performed on a prototype of an external control device operated by the legs. The 'Surveys on energy demand for at-home welfare devices for elderly people', showed how much the growth of the number of utilized devices will link to the cause to push up the energy demand in the household department in Japan. (NEDO)

  6. Achievement report for fiscal 1998 on the research and development of genome informatics technology. Development of energy use rationalization technologies; 1998 nendo genome informatics gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the field of the analysis of gene expression frequency information, a novel glass coating method and a highly sensitive high-speed reading device are developed. Element technologies are studied for the development of a detection system capable of high-density high-speed reading of high-density DNA capillary array, with a long-chain DNA probe solidified therein. In the technology of transcription control information analysis, concerning the technology of transcription dynamics analysis using tagged transcription control factors, the construction of a model system protocol is studied, an automatic analysis system is developed, and an evaluation technology is also developed. Furthermore, a novel method is proposed, in which two specimens will be prepared, that is, a microbead coupled DNA specimen consisting of base sequences of all combinations of a certain chain length and a cDNA (complementary deoxyribonucleic acid) derived protein specimen, and DNA-protein complexes will be isolated for analysis bead by bead out of a liquid which is a mixture of the said two specimens. (NEDO)

  7. Fiscal 1999 achievement report. Research and technology of important regional technologies (Development of combustion control system technology for rationalizing energy use); 1999 nendo energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For upgrading and optimizing combustion control systems, research and development is conducted for materializing SiC devices capable of high-temperature operation. In the development of basic technologies common to various types of SiC semiconductor devices, XeCl excimer laser annealing is applied to SiC implanted with Al ions, and low-damage ion implantation is studied. In the development of techniques for forming SiC single crystals into substrates, warpage of 20{mu} or less, surface coarseness of 5{mu}m or less, etc., are achieved in 1-inch and 2-inch wafers. In the development of SiC sensor technology, techniques of heteroepitaxial growth of 3C-SiC on Si substrates and of 6H-SiC on 6H-SiC wafers are established and an optical sensor is built experimentally. A high-temperature UV sensor, switching device for control, rectification device for control, etc., are built of nitrogen ion implanted 6H-SiC. In the effort to develop combustion control system technology, the principle of system operation of the combustion control method proposed under this project is verified. (NEDO)

  8. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use; 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa itaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper analyzes and puts into order the data surveyed and discussed on thirteen Welfare Techno-Houses (WTH) from a comprehensive viewpoint. It summarizes findings contributing to development and structuring of new at-home welfare device systems of effective energy utilization type. The paper first puts into order and discusses the survey and study items available for comparison and discussion, and the survey items with originality found in the surveys of the WTH, with which relatively large number of items were surveyed and studied among the thirteen locations nationwide. Next, the paper attempts comprehensive evaluation on the achievements thereof by the following items: (1) measurement and evaluation on energy consumption of different at-home welfare devices, (2) surveys and studies on energy demand evaluation inside and outside the residential houses arranged with considerations for elderly people according to the district characteristics, (3) evaluation on daily, weekly and annual changes in energy consumption in these houses, and (4) design and development of welfare systems of effective energy utilization type for these houses. Furthermore, the paper summarizes the general attributes of the WTHs in different districts, power consumption in these at-home welfare device systems in the WTH and energy consumption of the houses, in the forms available for comparison and discussion. Then, the paper summarizes the achievements of the present surveys and studies on the thirteen WTHs all over the country. (NEDO)

  9. Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (honpen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Efforts have been under way to prepare inter-industry relations tables and energy data for four Asian countries, namely, China, Taiwan, Singapore and Malaysia, and a tool for energy consumption efficiency analysis has been developed and improved. In Chapter 1, energy supply and demand in the above-named four countries is reviewed on the basis of recent economic situations in these countries. In Chapter 2, bilateral inter-industry relations tables usable under the project are employed for the analysis of the economic status of each of the countries and energy transactions between them, and a method is described of converting the tables into one-nation inter-industry relations tables which meet the need of this project. In Chapter 3, national characteristics reflected on the respective energy input tables are described, and a method is shown of converting a nationally characterized unit energy table into a common unit energy input table for registration with a database. In Chapter 4, the constitution of the Asian energy consumption efficiency improvement analyzing tool and a system using the tool are explained. In Chapter 5, some examples of analyses conducted by use of the analyzing tool are shown, in which the energy saving effect and CO2 emission reduction effect are estimated for Indonesia by use of the analyzing tool. (NEDO)

  10. Achievement report for fiscal 1998. Development of control system technologies such as combustion with energy consumption rationalized; 1998 nendo seika hokokusho. Energy shiyo gorkika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    To improve and optimize fuel control systems, basic technologies were studied for building SiC devices capable of high-temperature operation. The technologies involved the construction of single-crystal SiC substrates, development of element technologies such as conduction control, experimental production of SiC devices, and systems incorporating SiC devices for controlling, for example, combustion. The subjects of research and development for fiscal 1998 included the technologies related to common SiC semiconductor substrates (SiC substrate crystallinity evaluation by X-ray topography, thermal oxidation acceleration by ion irradiation, and annealing of ion-implanted SiC by excimer laser ), technologies of forming an SiC single crystal into a substrate, technologies related to SiC sensors, technologies related to SiC devices capable of operation at high temperature and high speed, technologies related to SiC devices for controlling, and technologies for controlling, for example, combustion. The subjects of basic researches at universities and research institutes included new crystal growing methods, ion beam-aided SiC synthesis, effect of irradiation of SiC with neutrons, and nuclear conversion implantation. (NEDO)

  11. Fiscal 1999 achievement report on interuniversity coordination type research and development of industrial technology. Research and development of highly functional material designing platform; 1999 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of enabling prediction of structures and properties of polymeric materials by computer-assisted experiments, studies were conducted for putting new simulation technologies to practical application. With the coarse-graining molecular dynamic method working group, a coarse-graining molecular dynamic engine high in generality and augmentability was developed so that an optimum coarse-graining model might be chosen and constructed to achieve any given purpose, and its installation was almost completed. The dynamic mean field method working group fabricated a new general-purpose simulator with its interface simplified and function improved. A simulation technique was also developed, which would be incorporated into the general-purpose simulator. The dispersed structure simulation working group developed a group of class libraries for use in continuum simulation. The platform working group, making use of Java excellent in general-purpose feature, worked out a function verification platform to run on Windows95/98/NT. (NEDO)

  12. Fiscal 1997 survey report. Survey consigned to NEDO of the development of energy use rationalization home welfare equipment systems; 1997 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa. Itaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of constructing new home welfare equipment systems of an energy effective use type, an investigational analysis was conducted of characteristics of the structure of houses considered of aged people, characteristics of the use of home welfare equipment, etc. As to the subject on space warming/cooling, it was found that the hour of stay-at-home of the aged tends to be longer, and the hour to be required for warming/cooling is longer, that the aged gradually lose senses regarding the peripheral environmental temperature, and the temperature to be considered should be at warmer/cooler levels, and that they are weak in heat shock, and the space of house where the temperature is uneven should be removed. Further, from the study in each welfare techno-house, possibilities were pointed out of further energy conservation in houses considered of the aged and home welfare equipment systems like the weight reduction of home welfare equipment systems and reduction of stand-by power, high air-tightness/high thermal insulation of houses for the aged, use of waste heat from air conditioners, introduction of solar energy to stand-by power and electrically-driven wheel chairs. 257 figs., 89 tabs.

  13. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Chofu City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Chofu) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper describes investigative studies on a new at-home welfare devices. Section 2 of the document, 'Studies on electric power conservation considering living patterns of elderly and physically handicapped persons' describes verification experiments in ferro-concrete buildings and ordinary homes by using a prototype system structured in last fiscal year. Qualitative analysis was performed based on the result thereof. In the 'Surveys on working environments for elderly people', directionality was presented in improving labor environments for the elderly people. Section 3, 'Studies on emergency evacuation devices for physically handicapped and elderly people' discovered that many of the presently available evacuation devices are intended of use mainly by handicap-free people, and there are many aspects that are difficult to say that elderly and physically handicapped people are included in the field of vision. In the 'Studies on an at-home training supporting system to maintain movement functions of the legs of elderly people', design and fabrication were performed on a prototype of an external control device operated by the legs. The 'Surveys on energy demand for at-home welfare devices for elderly people', showed how much the growth of the number of utilized devices will link to the cause to push up the energy demand in the household department in Japan. (NEDO)

  14. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Imaichi City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Imaichi) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Evaluations were given on energy demand in residential houses arranged with considerations for elderly people based on district features for at-home welfare devices, and on change in energy use at care-taking sites. Surveys and studies were performed on structural characteristics of residential houses arranged with considerations for elderly people, and on structuring of at-home welfare device systems. The study items are as follows: (1) identification of the using patterns of the at-home welfare devices, and measurement and evaluation on electric power consumption, (2) measurement and evaluation on household energy consumption, (3) estimation on energy demand in residential houses for elderly people, (4) surveys on hot heat sensitivity, and (5) estimation on allowance for steps in rooms. In Item 1, electric power consumption is measured during standard operation of at-home welfare devices by using power measuring devices in the Welfare Techno-House (WTH) Imaichi. In item 2, a questionnaire survey is performed on the ways of living in elderly people's households and general households. In Item 3, energy demand is estimated in houses for elderly people incorporated with welfare devices, based on the results of Items 1 and 2. In Item 4, measurement and evaluation are made by using experiments on physiological changes in bodies of elderly people in toilet space in the WTH, and on a room heating system giving comfortable feeling. In item 5, discussions are given on air tightness of doors in barrier free sections, and on allowable limit of steps inside rooms. (NEDO)

  15. Discussion on life cycle assessment on automobiles. 2. From a viewpoint of saving energy in the stage of their use; Jidosha no life cycle assessment ni kansuru ichikento. 2. Shiyo dankai no sho energy no shiten kara

    Energy Technology Data Exchange (ETDEWEB)

    Takeishi, T.; Kobayashi, N. [Nissan Motor Co. Ltd., Tokyo (Japan)

    1997-01-30

    Analysis was made by using the life cycle assessment method for the purpose of saving energy in the use stage of automobiles. Life cycle energy was calculated for cases of adopting direct fuel injection and non-stage transmission (CVT) in the currently used gasoline fueled cars. The calculation was performed with respect to each stage of raw material manufacturing, car fabrication, internal energy manufacturing, driving and disposal. Adoption of direct fuel injection and CVT technologies results in reducing the life cycle energy to about 30% in the use stage and little less than 30% on the whole. Stopping the idling operation will reduce the energy in the use stage by about 40%. Adoption of electric vehicles will result in energy reduction of 30% to 35% as compared with gasoline fueled cars. Since fuel consumption improves with increasing average car speed, energy consumption will be improved by about 30% if the current average car speed in the Tokyo Metropolitan area of 19 km/h is improved to the national average level. Improving the driving environments is important. Driving methods with less often quick starting and quick acceleration can save energy. Combinations of policies are desired, such as improvements in the currently used gasoline fueled vehicles, introduction of substitution fuel driven vehicles, and improvements in driving environments. 4 refs., 10 figs., 3 tabs.

  16. Fiscal 2000 survey report on technological trends. Survey on trend of high-density energy beam technology concerning conservation of energy; 2000 nendo gijutsu doko nado chosa hokokusho. Energy shiyo gorika ni kakawaru komitsudo energy beam technology no doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    There is a possibility that machining technology using high-density energy beam will bring an epoch-making change to micro-nano area processing. In particular, a laser beam having high controllability is indispensable. This is a report of the fiscal 2000 survey. The survey was conducted on laser beam generation, control and nano-diagnostic techniques, micro-nano optics technologies and machining technologies, with the development problems and targets summarized. Laser beam generation/control technologies, which become the basic tools for micro-nano manufacturing, were investigated, as were inspection technologies for the purpose of checking the functions of nano structures created. Particularly, the investigation elucidated the significance of development of a femtosecond solid state laser based on a semiconductor laser and the control techniques of their phase. Further, necessity was emphasized in developing X-ray probing, infrared and terahertz spectroscopy which are essential for nano-diagnostic techniques. In optics technologies, the paper described the importance of photonic crystals which enable less-than-wavelength machining or electrical beam control using interference effect. The possibility of fabricating photocatalysts with nano-particles was also mentioned, as was the manufacturing of nano-functional structures. (NEDO)

  17. International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). List of errata; 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo seigohyo. Asia energy shohi koritsuka bunseki tool chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The list of errata was prepared for the data book of the international measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). Corrected pages of the data book 1 (1990) are as follows: 187-190, 223-226, 259-262, 295- 298, 369-370, 387-388 and 405-406 on Malaysian data. Corrected pages of the data book 2 (1985) are as follows: 102-105 on Chinese data, 154 on common data, and 187-190, 223-226, 259-262, 295-298, 369-370, 387-388 and 405-406 on Malaysian data. (NEDO)

  18. FY 1974 Report on results of Sunshine Project. Research and development of slurry serviceable under geothermal conditions; 1974 nendo chinetsu kankyoka de shiyo kanona deisui no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-05-30

    Summarized herein are the results of (1) surveys on autoclaves, (2) researches on water/clay-based slurry materials, and (3) surveys on and designs of spent slurry treatment test systems. For the item (1), the autoclaves serviceable at normal working temperature of 250 degrees C and pressure of 500 kg/cm{sup 2} for testing slurry materials were surveyed, to set the maximum temperature of 300 degrees C and pressure of 300 kg/cm{sup 2} and volume of 200 cc. The autoclave satisfying the above conditions is to be purchased. For the item (2), surveys are still underway on agents, e.g., dispersantsand and deflocculants currently available both in Japan and abroad as the slurry components. Several types of dispersants and deflocculants were tested with slurries of low-solid suspensions containing 3 to 5 wt.% of bentonite, to follow their properties changing with content of the agent by a viscometer serviceable at high temperature and pressure, when the slurries are thermally treated at 150 to 200 degrees C. At the same time, the dispersants and deflocculants currently used were tested by an autoclave to follow thermal changes at 200 degrees C by an infrared spectrophotometer. For the item (3), surveys were conducted on spent slurry treatment test systems necessary for studying treatment of spent water/clay-based slurries. (NEDO)

  19. FY 1974 Report on results of Sunshine Project. Research and development of cement serviceable under geothermal conditions; 1974 nendo chinetsu kankyoka de shiyo kanona cement kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-30

    Researches are conducted for the (research and development of cement serviceable under geothermal conditions). The research items include (1) surveys on test apparatuses, (2) basic surveys on cement, additives and cement slurry, (3) R and D of cement, and (4) researches on cement additives and slurry. For the item (1), bright prospects are obtained that US's Chandler can supply a thickening time tester serviceable at up to 750 degrees F and 40,000 psi, and a cement curing device serviceable at up to 750 degrees F and 5,000 psi. For the item (2), the surveys are conducted on the existing techniques for curing reactions and chemical resistance of cement at elevated temperature and pressure. For the item (3), the researches are conducted to develop cement resistant to heat and sulfates for geothermal development purposes, where portland cement and mixed portland cement are used as the bases which are incorporated with silica powder. As a result, it is found that the optimum Ca/SiO{sub 2} and CaO/SiO{sub 2}+Al{sub 2}O{sub 3} molar ratios are around 1.0 to 0.9 and 0.9 to 0.8, respectively. For the item (4), the tests are conducted to determine adequate conditions of conductor pipe cementing and cement slurry for 1,500m deep geothermal wells, and the standard composition is established. (NEDO)

  20. Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    The project aims to prepare inter-industry relations tables and models for energy analysis for Asian countries and thereby to probe into relations between the industrial structure or the ultimate consumption structure and energy consumption. For the comprehension of energy consumption as broken by each industry, Asian nations' inter-industry relations tables and energy statistics are linked for the compilation of energy analysis oriented inter-industry relations tables, and the resultant tables are used for the metric analysis of industrial structures and energy consumption structures in these countries. The tables prepared this time are 1985 tables for Korea, Indonesia, Thailand, and the Philippines and 1990 tables for China, Singapore, and Malaysia. The Malaysian transportation sector needs to be improved in energy saving. In Singapore, energy saving is functioning effectively in the transportation sector. China's energy consuming industries are those involving coal, chemistry, steelmaking, ceramics, and earth and quarrying. In Taiwan, improvement needs to be made in the transportation sector. Korea should conserve energy in the transportation sector. In the Philippines, energy needs to be saved in businesses related to water supply, transportation, and fishery. Thai industries as a whole needs to save energy. Improved energy consumption efficiency is sought for in the Indonesian cement related sector. (NEDO)

  1. FY 1975 Report on results of Sunshine Project. Research and development of cement serviceable under geothermal conditions; 1975 nendo chinetsu kankyoka de shiyo kanona cement no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-30

    Three types of base geothermal cement were developed, on a trial basis, using C{sub 3}S(3Ca{center_dot}SiO{sub 2}) and C{sub 3}A(3CaO{center_dot}Al{sub 2}O{sub 3}), and incorporated with silica as the strength stabilizer, to prepare geothermal cement samples. They were tested for 45 days at a geothermal well in the Takinoue Geothermal District, showing a tendency of increasing in strength. The cement sample was prepared by incorporating 42.8% of the purest silica and 0.45% of lignin-based curing retardant. It showed a thickening time of 3 hours and 5 minutes. It showed a strength of 400 kg/cm{sup 2} or higher, when cured at 130 and 200 degrees C. The mixed cement, with G cement as the base incorporated with 42.8% of silica as the strength stabilizer, showed a thickening time of 4 hours and 12 minutes, when incorporated with 0.5% of a dispersant and 1.2% of a lignin-based curing retardant, where the G cement is developed for a 300 to 400 m deep geothermal well (maximum bed temperature: 220 degrees C, circulation temperature at the pit bottom: 135 degrees C), in accordance with the casing program for a 1,500 m deep geothermal well. When cured at 220 degrees C, it showed a strength of 370 kg/cm{sup 2} after it was tested for 15 days. (NEDO)

  2. Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    The project aims to prepare inter-industry relations tables and models for energy analysis for Asian countries and thereby to probe into relations between the industrial structure or the ultimate consumption structure and energy consumption. For the comprehension of energy consumption as broken by each industry, Asian nations' inter-industry relations tables and energy statistics are linked for the compilation of energy analysis oriented inter-industry relations tables, and the resultant tables are used for the metric analysis of industrial structures and energy consumption structures in these countries. The tables prepared this time are 1985 tables for Korea, Indonesia, Thailand, and the Philippines and 1990 tables for China, Singapore, and Malaysia. The Malaysian transportation sector needs to be improved in energy saving. In Singapore, energy saving is functioning effectively in the transportation sector. China's energy consuming industries are those involving coal, chemistry, steelmaking, ceramics, and earth and quarrying. In Taiwan, improvement needs to be made in the transportation sector. Korea should conserve energy in the transportation sector. In the Philippines, energy needs to be saved in businesses related to water supply, transportation, and fishery. Thai industries as a whole needs to save energy. Improved energy consumption efficiency is sought for in the Indonesian cement related sector. (NEDO)

  3. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use (Shizuoka City); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Shizuoka) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to achieve rationalization in energy use, surveys and studies were performed on structuring new at-home welfare device systems of effective energy utilization type, based on structural characteristics of residential houses arranged with considerations for elderly people, and operation characteristics of at-home welfare device systems. For the 'evaluation of daily, weekly and annual changes in energy use at care-taking sites', measurements were performed on cumulative power during operation standby and momentary power under no load and load in eight care-taking devices such as a care-taking Gatch bed, a motor-driven lift-up cooking table and a home elevator installed in the WTH Shizuoka, by using a house energy measuring device. The measurements verified that large power is consumed during standby operation. In developing the 'at-home welfare device systems that utilize energy more effectively', a solar beam measuring device was used to measure over an extended period of time the power generation amount of a solar beam power generation system installed in the WTH Shizuoka. Evaluation was given on the system as an emergency power supply for an emergency event, and consideration was given on the effectiveness of the system in the Shizuoka district where daily sunlight irradiation lasts long. Development was made on an inexpensive walking training device, on which effectiveness as a waling training device was evaluated by using a position sensor and a force plate. (NEDO)

  4. FY 1999 report on the results of the R and D of genom informatics technology. Development of technology for rationalization of energy use; 1999 nendo genom informatics gijutsu kenkyu kaihtsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In this R and D, studies were made on the following: 1) development of a circular-shaped DNA-chip (DNA disk) and analysis of the gene expression pattern network by the DNA disk; 2) analytical system with DNA capillary array for mRNA expression profile; 3) development of protein probe technique for isolation of transcription factor complexes, and of evaluation technique for functions of transcription factors and their target DNAs; 4) transcription control information analytical technology - study of detection operational technology and preparation technology of transcription control information analytical specimens; 5) general R and D issues. In 1), development is conducted of DNA chips and a DNA chip system which makes use of DNA chips. In 2), development is made of a DNA capillary array and its accurate and high-speed reader to analyze expression profile of mRNA in various pathological processes of diseases of unknown etiology. In 3), as development of genom informatics technology, analysis of correlations is made, paying attention to transcription factors which become the key to gene expression. In 4), study is carried out of gene transcription control information high speed screening technology. (NEDO)

  5. Report on achievements in fiscal 1998. Surveys on development of an at-home welfare device system to rationalize energy use. (Kobe); 1998 nendo energy shiyo gorika zaitaku fukushi kiki system kaihatsu chosa (Kobe) saiitaku kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the Kobe district, studies were performed with the importance placed on energy consumption at care-taking sites. Power consumption of devices used in residential houses of families having physically handicapped and elderly persons has been measured for two to three months, and in addition a questionnaire survey was carried out on operation frequency of welfare devices. Particularly from the power consumption and the use frequency of the devices to keep warm heat environment for physically handicapped and elderly persons, meaningful findings were obtained from the viewpoint of effective energy utilization, summarized as follows: (1) energy consumption of welfare devices used in care-taking sites in homes is small; (2) the power consumption varies greatly depending on methods to keep the warm heat environment; (3) in the case of discussing residential houses arranged with considerations for elderly people, the warm heat environment is important, and room cooling and warming devices including air conditioners should be included in the category of welfare devices, (4) a proposal was made on structuring a 'system to match elderly persons' physical conditions' intended to make a warm heat environment most suitable for physically handicapped and elderly persons, and (5) a proposal was made on discussing a 'system combining solar cells with large capacity batteries' of effective energy utilization type. (NEDO)

  6. Influence on driver fatigue of vertical vibrations over long distances. Assessment in terms of stress hormones; Driver no unten hiro ni okeru joge shindo no eikyo. Stress hormone wo shiyo to shite

    Energy Technology Data Exchange (ETDEWEB)

    Taguchi, T.; Inagaki, H. [Toyota Central Research and Development Labs., Inc., Aichi (Japan)

    1998-05-01

    Driving tests are conducted to obtain some indexes that describe the cumulative effect of the sense of tiredness. The heart rate, Mayer wave related sinus arrhythmia, respiratory sinus arrhythmia, urinary adrenaline, noradrenaline, and cortisol in saliva are tested. Adrenaline and Mayer wave related sinus arrhythmia are ultimately named in view of their correlation with tiredness. It is believed that tiredness is attributable to two factors, which are increase in mental stress and decrease in vigilance. An excitation test is then conducted using a motion simulator. Upon application of 4Hz vibrations (equivalent to the chest section resonance frequency), adrenaline increases sharply, and then decreases sharply upon termination of excitation. Upon application of 1.6Hz vibrations (equivalent to the head section resonance frequency), adrenaline increases but not sharply, and the elevated level is sustained for some time after excitation. Driving tests are next conducted using a vehicle with its suspension fixed and another with 1-2Hz vibrations reduced. Rise in the adrenaline level is found inhibited aboard the latter. No difference is detected in terms of Mayer wave related sinus arrhythmia between the two vehicles. 4 refs., 7 figs., 4 tabs.

  7. Fiscal 1998 research report. International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    This project aims to prepare the inter-industry relations table and analysis model for energy analysis for every Asian country, and analyze the relation between energy consumption and industrial structure or final demand structure. The 1985 and 1990 inter-industry relations tables of each country were prepared in cooperation with the governmental organizations of China, Korea, Taiwan, Philippines, Thailand, Malaysia, Singapore and India. However, the 1987 and 1990 tables were prepared for China. In fiscal 1998, the project invited the representatives of each concerned organization, and held the international workshop together with Japanese specialists to discuss various issues related to not only table preparation but also data analysis. The following items were analyzed for every country: a change in final energy consumption, a dependence on coal in primary energy consumption, transfer of energy consumption to other energy resources, and an energy consumption rate in the whole industry. (NEDO)

  8. Report on FY 1998 project for international energy utilization rationalization, etc. (Project of the analytical tool survey for making energy consumption effective in Asia); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the Asian region, for the purpose of grasping effects of both economic growth and effective energy consumption, an analytical tool added with a computational function was developed with the interindustrial relations table as database for the analysis of the present situation and the simulational analysis. In the analysis of the present situation, changes between the two time-points, 1985 and 1990, were analyzed using the developed energy consumption table and the CO2 emission table. The energy consumption amount is increasing with the growing economy. However, the energy unit consumption is decreasing in countries except Korea, the Philippines, Singapore and Malaysia. The trend is that the energy consumption is becoming effective and the CO2 emission amount is decreasing. As an example of simulating the introduction effect of energy saving technology, the simulation was conducted on the three: iron steel, paper/pulp, and cement in Indonesia. As a result, the decrease in energy consumption was shown in paper/pulp by 48%, in cement by 16%, and in iron/steel by 16%. The same was also indicated in CO2 emission. (NEDO)

  9. FY 1998 annual summary report on project for international energy consumption rationalization. Survey on analysis tool for improving efficiency of Asian energy consumption (data book 2 for 1985); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 2 1985 nen data)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The data book is compiled, based on common industrial classifications, as the tool for analyzing, e.g., the mutual ripple effects of economic growth and increased efficiency of energy consumption throughout the Asia-Pacific region. This book summarizes the industrial-related and energy-related tables for 8 Asian countries and Japan. The book II is for the 1985 data (1987 data for China), comparing with the book I for the 1990 data. The industry-related tables are composed of the tables for transaction bases, input coefficients, final demand converters, importation coefficients, inverse matrices, sensitivity/influence coefficients, production inducement levels, production inducement coefficients, degrees of dependence on production inducement, importation inducement levels, importation inducement coefficients, and degrees of dependence on importation inducement. Energy-related tables are composed of the tables for, e.g., energy input, energy consumption, emissions, and CO2 emissions. (NEDO)

  10. Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

  11. Fiscal 1999 achievement report on research and development of industrial technology of new industry creation type. Research and development of intelligent material and structural system (Development of energy use rationalization technology); 1999 nendo chiteki zairyo kozo system no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Fiber or foil shaped sensor materials and actuator devices were integrated with composite materials and composite material structures for processing and controlling information, and then studies were conducted about materials and structural systems for enabling real-time detection of damage in materials and structures, examination of soundness, control of noise and vibration, and the like. Concerning optical fiber sensors in the development of smart manufacturing technologies, the impact imposed on composite materials by sensors embedded therein was investigated, and the scope of their applicability was determined. In the development of actuator materials and devices, ceramic actuators were fabricated by microwave sintering, and it was found that they were higher in performance by 30% than actuators of the conventional design. In the testing of demonstrators, molded body monitor basic tests using optical fiber sensors were conducted for jet engine static vane models, and temperature dependence of optical intensity was understood. (NEDO)

  12. Survey report for fiscal 1998. International project for rationalizing energy use (a project for investigating analyzing a tool to improve energy consumption efficiency in Asia) (Data collection 1 (Year 1990 data)); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 1 1990 nen data)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to identify quantitatively the mutually influencing effect of economical development and energy consumption efficiency improvement in the entire Asia-Pacific region, a data collection was prepared according to the common industry classification as a tool to analyze energy consumption improvement in Asia. This data collection summarizes the industry relation tables and the energy relation tables available in eight Asian countries (Korea, Indonesia, Thailand, Philippines, China, Taiwan, Singapore and Malaysia) and Japan. Both kinds of the tables are unified in conception among the nations, hence comparable. The industry relation table consists of a basic transaction table, a charged coefficient table, a final demand converter table, an import coefficient table, a reverse matrix table, a sensitivity coefficient able, an influence force coefficient table, a production inducing amount table, a production inducing coefficient table, a production induction dependence table, an import inducing amount table, an import induction coefficient table, and an import induction dependence table. The energy table consists of an energy input table, an energy consumption table, and an emission table. (NEDO)

  13. Report on achievements in fiscal 1999. Development of energy usage rationalizing silicon manufacturing process (Development of manufacturing technology for mass production of silicon for solar cells); 1999 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchiyo silicon ryosanka seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Discussions were given on manufacture of raw material silicon for solar cells with regard to boron removal, solidification, finishing and refining of metallic impurities, refining of unutilized silicon scraps, and making them into wafers and solar cells after refining. This paper summarizes the achievements in fiscal 1999. With regard to purity deterioration due to contamination by boron containing silica powder generated during the boron removal in the manufacturing process, the facilities were modified resulting in the reduction thereof to 0.04 ppmw or less. Regarding the repetitive use of boron removing crucibles, the experiment identified the possibility of using them for more than three times. In trial fabrication of samples by using the solidification refining and cast integrated process, ingots of 550 mm square and about 300 mm high were obtained, which were sliced into 10-cm square materials for use as wafers. Measurement of the conversion efficiency has resulted in 13% or more which is almost equivalent in the center and edges of the ingot. It was revealed that solar cell wafers may be fabricated by using this process, which can use either the p-type low-resistance silicon scraps or the metallic silicon as the starting material. (NEDO)

  14. FY 2000 International energy use rationalization project. International technology dissemination project for improving energy consumption efficiency (Green helmet project for steel heating furnaces in Thailand); 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Kokusai energy shohi koritsuka nado gijutsu fukyu jigyo (Green helmet jigyo (Tai: kozai kanetsuro))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project for energy saving dissemination activities and technological assistance for Thailand is carried out, and the FY 2000 results are reported. For Siam Iron and Steel (SISCO), the experts are dispatched for reviewing the operating conditions of the facilities constructed by the model project, their maintenance and examination, time series diagnosis of the recuperator performance, and providing technical assistance for fuel consumption and high-load combustion of the downstream unit. Furthermore, the site survey and technical assistance are provided for two newly selected Thai steel enterprises, Sahaviriya Steel Industries Public Co. (SSI) and the Bangkok Iron and Steel Works Co. (BISW). For SSI, it is predicted that energy of approximately 50Mcal/ton can be saved by, e.g., enhancement of waste heat recovery, enhancement of heat insulation of skid pipes, introduction of steel discharging temperature prediction system, and combustion control. For BISW, it is predicted that energy of approximately 25Mcal/ton can be saved by, e.g., enhancement of waste heat recovery and reduction of heat loss in the waste gas. (NEDO)

  15. Fiscal 1999 achievement report. Development of technology for machine tool with energy consumption rationalized (Research and development of environment-conscious grinding system); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A large quantity of coolant is used in the grinding process for ensuring high accuracy and quality in the work. This presents a serious problem from the viewpoint of environmental impact or energy conservation, and now environment-conscious grinding methods requiring no or less coolant are sought for. With a view to answering the demand, efforts are exerted to put to practical use, and improve, an EcoloG grinding technique. The goal is to reduce to half the energy that the grinding process is now consuming. The EcoloG technique is a grinding method under which vegetable oil mist is cooled for lubrication and a small amount of cooling water is fed to the point of grinding for removing chips. In fiscal 1999, a survey was conducted on technical literature, patents, and the like in and out of Japan for the study of the actual state of dry machining, and then the course of future studies was clearly established. Studies were also carried out aiming at the practical application and improvement of the EcoloG grinding technique, and the technique achieved a quality level as high as that of the conventional coolant-aided method in a process of grinding a shaft to have an accurate outer diameter by use of an ordinary wheel head. (NEDO)

  16. FY 1999 Report on research and development of energy utilization rationalization superhigh-technological liquid crystal technologies. Superhigh-technological electronic technology development promotion project for new functional electronic material design, control and analysis technologies; 1999 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    Described herein are the FY 1999 results of the liquid crystal technology development project. For the researches on multi-layer reflection, composite panels of flattened resins of different refractive index are developed to improve 2-layer monochromic contrast ratio. The guest/host liquid crystal compositions of high orientation order are investigated as the those useful for high contrast. Compounds are pursued for superanisotropic light absorption, and modification with a substituent is found to be effective. Molecular orientation controlling is also studied. For researches on memory-sustaining type liquid crystals, the studied items include formation of thin ferroelectric films on glass substrates, improvement of voltage-sustaining characteristics by composites (including compounds), and doping of trace quantities of ionic impurities. For development of image element colors, the studied items include multi-lattice-structured, oriented HPDLC devices, composites of high birefringence (high order light scattering), and light interference, high order light scattering type light control devices. The multi-dimensionally anisotropic structure of configuration divided into 3 parts of R, G and B is developed to create directive reflection which improves brightness of the reflection type color liquid crystal. A group of compounds are pursued to develop liquid crystal compositions of high refractive index anisotropy, and promising ones are found. The results of the comprehensive investigations are also described. (NEDO)

  17. Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Development of energy use rationalization technology); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop self-complete type purification ceramic materials in which selection, separation, and purification functions are merged with the energy conversion function. Activities are conducted in the three fields of developing (1) materials derivation technology, (2) application technology, and (3) common base technology. In relation to selection, separation, and purification functions in field (1), studies are made about electrochemical cell structure control and cell constituting materials for enabling a high efficiency NOx purification reaction. As for the energy conversion function, studies are made about the improvement of characteristics of oxide based thermoelectric conversion materials and about changes in electrical output due to their development into cells. In a study of novel thermoelectric conversion materials, K{sub 2}NiF{sub 4} type Y{sub 0.33}Sr{sub 1.67}(Ni{sub 1-y}Co{sub y})O{sub 4-{sigma}} and Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 1-y}M{sub y})O{sub 4-{sigma}} (M=Fe, Co) are synthesized, and electrical resistivity levels and Seebeck coefficients are determined at room temperature-800 degrees C in an oxygen current. Seebeck coefficients are found to be negative for all specimens, which shows that they are n-type conductors. Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 0.7}Fe{sub 0.8})O{sub 4-{sigma}} exhibits the greatest output factor of 0.064 times 10{sup -4}Wm{sup -1}K{sup -2} (400 degrees C). (NEDO)

  18. Fiscal 2000 research achievement report on the development of super-advanced liquid crystal technology for energy use rationalization. Development promotion project for super-advanced electronic technology - Design, control, analysis, etc., of electronic materials having novel functions; 2000 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo (shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    Efforts are focused on the verification of target devices under the respective subjects, and activities are conducted with the development system reinforced. Three newly proposed reflection type liquid crystal devices achieve the target specifications of a reflection factor of 60% or higher and a contrast ratio of 15:1 or higher. Studies are conducted involving the five fields of (1) multilayer reflection devices, (2) memory retention liquid crystal devices, (3) single pixel color devices, (4) directional reflection devices, and (5) joint research. Research and development in field (1) covers ultra-anisotropic optical materials, ultrahigh reliability host liquid crystal materials for guest-host liquid crystals - mixed system, low voltage driven/high load holding liquid crystal compound systems, and new liquid crystal molecule orientation control technology; in field (2), low temperature fabrication of ferroelectric thin film, and ultrahigh purity high reliability liquid crystal compounds; in field (3), materials capable of controlling optical interference and higher order light scattering, photoregulation devices, highly birefringent liquid crystal materials - mixed system, and ultrahigh efficiency light scattering liquid crystal compounds; and, in field (4), multi-dimensional anisotropic structure fabrication technology and ultra-anisotropic optical materials. (NEDO)

  19. Fiscal 2000 survey report on rationalization project for international energy conservation, technological dissemination project for international energy conservation, and Green Helmet Project. Japan-China alternative energy seminar/waste disposal; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo, kokusai energy shohi koritsuka nado gijutsu fukyu jigyo, green helmet jigyo chosa hokokusho. Nicchu sekiyu daitai energy seminar haikibutsu shori

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper explains the Japan-China alternative energy seminar (February 28 and March 1, 2001, at Beijing). The purpose of the seminar is to introduce systematic and three-dimensional or land/sea/air measures for waste disposal including recycling in Japan, to provide guidance of measures in improving recognition and methods for waste disposal in China, and also to contribute to the dissemination and promotion of a model project for effectively utilizing waste heat from rubbish incineration, a project being implemented in Harbin City now. The activities of NEDO were introduced, with emphasis placed on a model program, called Green Aid Project, for managing heat from waste incineration. On the subjects of sustainable development, urban environment, and energy, the policy of China's tenth five-year plan was demonstrated, and the treatment of wastes in China was also explained. The present state of waste processing in Japan was introduced, as was its maintenance of the facilities. Concerning Japan's waste processing technologies and characteristics of the equipment, there were presented non-incineration processing including crushing/separating, RDF, compost, methane fermentation, etc.; incineration plants; and each of the technologies such as combustion, exhaust gas, ash treatment, use of remaining heat, and gasification melting. (NEDO)

  20. Achievement report for fiscal 1998 on research and development project for university coordinated type industrial science technologies. Research and development on platform for designing high functional materials (development for practical use of technologies related to rationalization of energy use); 1998 nendo kokino zairyo sekkei platform no kenkyu kaihatsu. Energy shiyo gorikia kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper reports research achievements in fiscal 1998 for a platform for designing high functional materials. Since coarse-grained models used in molecular dynamics (MD) simulation are diversified depending on materials, phenomena and properties, a general purpose MD engine that can simulate them freely was designed. Methods were developed to determine the potentials of coarse-grained models from the atomistic models. In polymer melts, very slow movements caused by entanglements have a substantially important role, which are difficult to be studied by usual MD simulations. Therefore, fiscal 1998 has devised a coarse-grained model to handle slow movements of straight-chain polymers, and a rheological forecast program was prepared. Studies are also being made on meso-scale structures sufficiently large as compared to atoms and on dynamic property forecast. Works were carried out to develop a simulator, in which polymeric phenomena with large spatio-temporal scale are applied with a continuity model to solve the equation thereof. Improvements were given on the hardware/software environments required for developing simulation engines and platforms for mesoscopic region. (NEDO)

  1. FY 2000 report on the survey of the project for arrangement of the basis of the international energy utilization rationalization. Survey of diagnosis of energy conservation in main industries of ASEAN countries; 2000 nendo kokusai energy shiyo gorika kiban seibi jigyo chosa hokokusho. ASEAN shokoku shuyo sangyo ni okeru sho energy shindan chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of securing the stable energy supply/demand and contributing to the sustainable economic growth in ASEAN countries, survey of the diagnosis of energy conservation was conducted. In this survey, the diagnosis on energy conservation was made in terms of typical plants/works jointly with ASEAN-side engineers to grasp the actual state of energy consumption of each of the plants and to give advice on energy conservation policies. The countries and companies selected as objects in this fiscal year are a fiber plant in Malaysia (Arab-Malaysian Development Berhad), a paper mill in Indonesia (P.T.Kertas Leces Pulp Paper Mill) and a cement plant in Brunei (Butra Djajanti Cement SDN BHD). Diagnosis was made for each of them on January 15-19, on January 22-26 and on February 5-9, 2001, respectively. Through Workshops No. 1 (November 2000) and No. 2 (December 2000), this diagnosis program was carried out in 2001. On the basis of the results of the diagnosis, presented were the necessary energy conservation policies to be taken. (NEDO)

  2. FY 2000 report on the results of the technology development of energy use reduced machine tools, etc. Development of the linear motor system for realization of energy conservation and commercialization; 2000 nendo energy shiyo gorika kosaku kiki nado gijutsu kaihatsu seika hokokusho. Shoeneka to jitsuyoka wo jitsugensuru linear motor system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation to the drive system of machine tools widely used as production facilities for automobiles, home electric appliances, etc., the R and D were made of a high efficiency linear motor system of which attention was paid to energy rationalization and environmental loads, and the FY 2000 results were summed up. In the study of the development of the system, studies were made not only on the lowering of heating, cost reduction and heightening of speed, but on the mechanism and control by which machine natural vibration can relatively be cut off, technology of damping for cutting vibration, technology to meet the deformation, etc. by cutting loads, sliding loads, and acceleration of accelerating/decelerating, technology to reduce the machine weight, etc. In the study of the basic technology of linear motor, the finite element method analysis was conducted on the typical linear motor. Concerning the control system, specs were studied which can deal with natural vibration and cutting vibration of the machine system. As to the development of the steel scale type linear encoder, scale sample for evaluation of basic characteristics was designed/trially manufactured. In the study of the detection optical system, the design/trial manufacture of photodiode array were made. (NEDO)

  3. Achievement report for fiscal 2000 on operational research of human cooperative and coexisting (humanoid) robot system. Development of energy usage rationalizing technology; 2000 nendo ningen kyocho kyozongata robot system un'yo kenkyu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in the operational research on the human cooperative and coexisting (humanoid) robot system to rationalize energy usage. Operational method and maintenance were studied on the platform hardware that has been developed in the previous fiscal year. Checks were given periodically on the robot platform hardware, and no anomalies were verified in all operation. Verifications were made on the fasteners, additional tightening, fitting of the connectors, battery checks, zero position and step response checks, and output checks on the force component sensor, gyro sensor and G sensor. For the virtual robot platform, discussions were given on the basic movement library for the geography complying three-dimensional walking. Such configurations were constituted that integrated use is possible with the simulator system by connecting the networks, and the user can instruct the CORBA server with the generation of walking movements according to the GUI by using the general purpose WWW browser to connect it to the HTTP server, whose result can be verified by three-dimensional graphics. A method to stabilize the all-axis movement servo model was made open to public. (NEDO)

  4. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Survey and study of analysis of commercialization of solar-grade silicon material manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Taiyodenchiyou silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The trend of technology development, problems harbored therein, trend of the market, and the like were investigated for supporting the development of technologies for the mass production and commercialization of solar-grade silicon materials. Concerning the future of production enhancement and cost reduction in the manufacture of polycrystalline silicon solar cells, studies were made from the technological viewpoint. The results are shown below. It is estimated that approximately 4,500 tons of material silicon will be necessary in 2005 and 6,500-10,700 tons in 2010. Since the melting purification method of NEDO (New Energy and Industrial Technology Development Organization) now under development step by step toward commercialization as well as the conventional source will provide the necessary amount of material silicon, it is inferred that the development of solar cells will go on without any restraint originating in the semiconductor industry. With the commercialization of the technologies so far developed and the development/commercialization of the fast-acting high-performance solar cell technology, probabilities are high that the polycrystalline silicon solar cell manufacturing cost in 2010 will be as low as to be on the 100 yen/W (93-118 yen/W) level which is the level now held up as the goal. (NEDO)

  5. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (Development of technologies for rational use of energy); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, as part of development of technologies for rational use of energy. The program for development of health monitoring technologies produces the bright prospects for commercialization of the fine FBG (Fiber Bragg Grating) sensor which can be embedded in a CFRP prepreg, and establishes the crack detecting method. The program for development of smart manufacturing technologies describes the dielectric constant sensor capable of monitoring the curing process, detection of the cured conditions by the optical fiber sensor, and development of the performs by RTM (Resin Transfer Molding). The program for technological development of the active-adaptive structures conducts the vibration- and noise-controlling tests for the small-size structural elements, confirming that the damping coefficient is improved by at least 20% and acoustic power is reduced by at least 30%. The program for developing the actuator materials and elements improves the piezoelectric characteristics of the PZT-based materials by hybrid sintering, and develops the actuators of high-durability FGM (Function-Gradient Materials). It also develops the foil- and belt-shaped shape memory alloys by arc-aided dissolution and rapid solidification of Ti-Ni-Cu-based alloys. (NEDO)

  6. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems (Development of practical technology for rational use of energy); 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of development of intelligent material/structure systems, study was made on practical technology for rational use of energy. For resource saving and energy saving (smartening) for large and complex machines and structure systems, light-weight long-life materials/structures are indispensable. Study was thus made on the basic technology of material/structure systems equipped with realtime defect detection function, structural integrity diagnosis function and control function of noise and vibration through information processing and control by integrating composite material/structure and fiber or film sensor material/device. For development of smartening technology, sensing technology was studied to detect the interior structure of composite material/structure compacts. The basic fabrication technology of ceramic actuator materials/devices, and shape memory alloy system actuators were put into development. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends for forming common knowledge. (NEDO)

  7. FY 2000 report on the results of the R and D of the technology for rationalization of energy utilization and for CO2 fixation using recycled paper; 2000 nendo energy shiyo gorika koshi nado yuko riyo nisanka tanso koteika gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this R and D, the recycled paper, etc. composed mainly of cellulose are degraded (saccharified) up to saccharides in a biological method. The saccharides and CO2 obtained are converted into useful substances such as organic acid using the bacterium function. The aim of the R and D is to develop this conversion (bioconversion) technology and to establish the technology to make an effective use of the recycled paper, etc. as useful chemical raw materials/substances and energy. In FY 2000, study was made mostly of the saccharification and bioconversion. As to the saccharification, conducted were the collection of the bacteria for cellulose degrading enzyme production which have been found so far and the evaluation of degradation of the recycled paper. And, as to the bioconversion, conducted were the survey and isolation of enzyme proteins and genes which are concerned in it in the process toward the formation to organic acid from saccharides and CO2, and the analysis of part of them. In this report, introductory remarks were described in Chapter 1. In Chapter 2, the results were summarized of the study on saccharification of the recycled paper. In Chapter 3, the results were outlined of the study on the bioconversion technology. This technology development was aimed at establishing new high efficiency bio-processes. (NEDO)

  8. FY 1999 achievement report on the project on the R and D of university-cooperation industrial science technology. Semiconductor device production process by Cat-CVD method (Development of the technology to rationalize energy utilization); 1999 nendo Cat-CVD ho ni yoru handotai device seizo process seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results obtained by FY 1999 of the semiconductor device production using the catalytic chemical vapor deposition method. As to the application to Ga-As integrated circuits, a guide was acquired for the accumulation speed over 40nm/min. The 5% thickness distribution of inner film of 4-inch wafer, refractive index distribution of 1% or less, and 2D electron gas concentration change of 1.5% could be realized. The experimental device for commercialization was designed and manufactured. Concerning the application to ferroelectric integrated circuits, the accumulation temperature condition was refined as 200 degrees C or less, which resulted in succeeding in forming Si{sub 3}N{sub 4} film at low temperature of 120 degrees C (accumulation speed: 20nm/min.) Relating to the application to Si integrated circuits, a machine to cope with 8 inches was developed. The 6-inch film thickness distribution of 5% and the refractive index distribution of 1% were realized. In regard to the leak current, extreme-thin film was superior to thermal oxidation film. About the application to the formation of high-quality thermal insulation thin films for low temperature polycrystal Si thin film transistor use, poly-Si films with a Hall effect mobility of approximately 10cm{sup 2}/Vs which is relatively high could be formed. In addition, the design/manufacture of Cat-CVD device with a large area were made. (NEDO)

  9. FY 2000 survey report on the project for preparation of the international energy utilization rationalization basis. 1st volume. Survey/study for the spread of energy conservation technology; 2000 nendo chosa hokokusho. Kokusai energy shiyo gorika kiban seibi jigyo (Sho energy gijutsu no fukyu no tameno chosa kenkyu to - 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In China which is the largest energy consumption country in the Asian region and has much room for the spread of energy conservation technology, investigational study was made with the aim of widely spreading energy conservation technology and solving environmental problems. To grasp energy supply/demand in China, environmental problems, industrial structure and social system, it is necessary to have process for establishment of data monitoring method, construction of database and model simulation. Proposal for model simulation was made. Further, to make macro-basis assessment of potentiality of energy conservation and environmental effect by sector in China, following the previous fiscal year, study was made on the electric power industry, where there is big potentiality of heightening energy utilization efficiency but the rationalization is not proceeded with. Moreover, in this fiscal year, energy demand is expected to increase with the growing economy, and the traffic field which has a great effect on the environment was added to the investigational research. (NEDO)

  10. Fiscal 2000 technology trend survey. Survey and study report on the development of high-frequency devices to support IT revolution leading to energy use rationalization; 2000 nendo gijutsu doko to chosa. Energy shiyo gorika ni kakawaru IT kakumei wo support suru koshuha device no kaihatsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Surveys and studies were conducted for the development of technologies basic to the construction of an ultrahigh-speed huge-capacity high-frequency radio access and communication network, especially the network infrastructure, in the several 10 to several 100 GHz band. Some surveys covered the positioning of high-frequency high-output device modules as the key component, needs for their use in radio communication equipment, devices to be needed for their construction, technologies for their manufacture, process technologies for their embodiment, basic technologies for their materials, and so forth. Some others covered research on the marketability of high-frequency devices in the future, development of relevant technologies abroad, and so forth. The mainstream of high-frequency devices these days rests on the secondary electron gas system based on GaAs and InP, and therefore it is intrinsically difficult for them to yield high outputs. It is deemed to be important to develop technologies based on novel semiconductor materials, such as nitride semiconductors which have excellent properties as materials, toward the construction of a network infrastructure for the next generation. (NEDO)

  11. Achievement Report for fiscal 1997 on developing a silicon manufacturing process with reduced energy consumption. Development of silicon mass-production manufacturing technology for solar cells; 1997 nendo energy shiyo gorika silicon seizo process kaihatsu. Taiyo denchiyo silicon ryosanka seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to manufacture silicon for solar cells, development is intended on a technology to manufacture silicon (SOG-Si) for solar cells by means of metallurgical methods using metallic silicon with purity generally available as an interim starting material. The silicon is required of p-type electric conductivity characteristics with specific resistance of 0.5 to 1.5 ohm per cm, to be sufficient even with 6-7N as compared to silicon for semiconductors (11-N), and to be low in cost. While the NEDO fluid bed process and the metallurgical NEDO direct reduction process have been developed based on the technology to manufacture silicon for semiconductors, the basic policy was established to develop a new manufacturing method using commercially available high-purity metallic silicon as an interim starting material, with an objective to achieve cost as low as capable of responding to small-quantity phase production for proliferation purpose. Removal of boron and phosphor has been the main issue in the development, whereas SOG-Si was manufactured in a laboratory scale by combining with the conventional component technologies in fiscal 1991 and 1992. The scale was expanded to 20 kg since fiscal 1993, and a five year plan starting fiscal 1996 was decided to develop the technology for industrial scale. Fiscal 1997 has promoted the development by using the 20-kg scale device, and introduced facilities to develop technology for mass-production scale. (NEDO)

  12. Development in fiscal 1998 of silicon manufacturing process to rationalize energy usage. Surveys and researches on analysis of practical application of technology to manufacture silicon raw materials for solar cells; 1998 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to develop a mass production technology to manufacture silicon raw materials for solar cells, and assist its practical application, surveys and analyses were performed on trends in development of the related technologies, the problems therein , market trends and industrial trends thereof. This paper summarizes the achievements in fiscal 1998. The worldwide production amount of solar cells in 1998 is estimated to have achieved 150 MW, and the silicon consumption reached the level of 2,300 tons. In spite of the economic recession environment, there was no change in the expansion trend. In developing an SOG-Si mass production and manufacturing technology, construction of pilot plants for each process has been completed, and entered into the operation research phase. In developing a technology to manufacture high quality poly-crystalline silicon substrates, fabrication has been completed on the on-line ingot cutting equipment and the plasma heating equipment, and the stage is now in operation research of continuous electromagnetic casting process. The conversion efficiency of the poly-crystalline silicon solar cells is 14 to 16% at the mass production level, whose enhancement requires indispensably the improvement in quality of the substrate. Discussions are required on the ingot manufacturing conditions in coordination with improvement in the cell manufacturing technology. (NEDO)

  13. FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the technology to rationalize energy utilization; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the FY 2000 results. In Chapter 1, development of electrically high functional diamond process technology, electric characteristics which frontier carbon materials have were made clear by the following four subjects, and the development was executed of original production process technology for realizing energy saving by heightening efficiency of electric devices, displays, etc. 1) development of morphology control; 2) development of technology to control electron emission characteristics; 3) development of technology to control oriented growth; 4) development of technology to enlarge single crystals. In Chapter 2, the basement technology of electron emission control was studied. Namely, conditions for film formation were investigated to elucidate the formation mechanism of carbon nano structure films by Dual RF CVD method, IPC CVD method and thermal CVD method. As to the electron emission mechanism of diamond, electron emission characteristics were outlined of the boron dope diamond thin film formed by micro wave plasma CVD method in FY 1999. In Chapter 3, investigational study of original production process technology of electrically high function materials, test study was made of the element technology needed to make high quality/large area diamond substrates. (NEDO)

  14. Industrial science and technology research and development project of university cooperative type in fiscal 2000. Report on achievements in semiconductor device manufacturing processes using Cat-CVD method (Development of technology to rationalize energy usage); 2000 nendo daigaku renkeigata sangyo kagaku gijutsu kenkyu kaihatsu project. Cat-CVD ho ni yoru handotai device seizo process seika hokokusho (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The catalytic chemical vapor deposition (Cat-CVD) method is a low-temperature thin film depositing technology that can achieve improvement in quality of semiconductor thin films and can perform inexpensive film deposition in a large area. This paper summarizes the achievements in fiscal 2000 in the demonstrative research and development theme of the present project, centering on the following five areas: 1) discussions on application of the Cat-CVD method to the mass production process for gallium arsenide integrated circuits, 2) studies on the possibility to apply the Cat-CVD method to the process to fabricate nitrided silicon protective film for ferroelectric memory devices, 3) formation of nitrided silicon films for silicon integrated circuits by means of the Cat-CVD method, and development of a chamber cleaning technology, 4) fabrication of high-mobility poly-crystalline silicon thin film transistors formed by using the Cat-CVD method and large particle size poly-crystalline silicon films by using the catalytic chemical sputtering process, and 5) discussions on properties of amorphous silicon thin film transistors formed by using the Cat-CVD method and formation of large area films by using a catalyst integrated shower head. (NEDO)

  15. Report on fiscal 1999 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (development of technology for rationalizing use of energy); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    R and D was conducted on original processing technology for electrically functional materials as a R and D project on frontier carbon technology, with the results for fiscal 1999 compiled. In the development of film forming technology using a large morphology control film forming device, the device was introduced this year, with film forming conditions probed. In the development of large size diamond synthesis process, single crystal synthesis and evaluation were carried out using an existing microwave plasma CVD reactor, with a study of design made for the device for obtaining a target 16 mm diameter single crystal. In the development of technology for oriented diamond growth on a platinum-based metallic base plate, research was done for controlling generation of grain boundary in a diamond film, through the improvement of orientation and the reduction of non-oriented grain density of the diamond nucleated on the base plate. The studies on control technology of surface-interface and electron emission characteristics were conducted on such subjects as fabrication technology of diamond for field emission, characterization of field emission, and photoelectron emission spectroscopy of diamond. (NEDO)

  16. Fiscal 2000 technology trend survey. Survey of technology trend relating to next-generation metal-based material compatible with inverse manufacturing leading to energy use rationalization; 2000 nendo gijutsu doko chosa hokokusho. Energy shiyo gorika ni kakawaru inverse manufacturing ni tekigoushita jisedai kinzoku kei zairyo ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the construction of a recycling system consuming less energy and therefore higher in efficiency, studies were made about the feasibility of metallic material developing/recycling systems more congruent with the objective through the application of inverse manufacturing (IM). Concerning metallic materials and recycling technologies, steel, aluminum alloys, and magnesium alloys were taken up, and a survey was made of hazardous elements in steel materials, unification of materials to constitute aluminum alloy parts, yield of magnesium in die casting, and the like. In the survey of recycling of automobiles, it was pointed out that the treatment of resin-based shredder dust was posing problems and that the use of metallic materials high in recyclability was essential to IM. In conclusion, three propositions were presented, which involved technologies for the advanced use of magnesium alloys as materials leading to the realization of IM, the development of recycling-oriented general-purpose alloys (with Mg and Al as mother metals), and the development of functional bonding technology enabling debonding (debondable bonding technology). (NEDO)

  17. Achievement report for fiscal 1998 on area consortium research and development business. Area consortium for venture business development by building base for small business (abuse double protected next generation card system based on steganography); 1998 nendo venture kigyo ikuseigata chiiki consortium kenkyu kaihatsu (chusho kigyo sozo kibangata). Steganography gijutsu wo riyoshita jisedaigata fusei shiyo taju boshi guard system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A card system is developed using BPCS (Business Planning and Control System) steganography, with electronic data imbedded in the card. Under the system, the visual recognition of the user and the mechanical verification of the card are carried out simultaneously, with the card rejecting any abuse. In fiscal 1998, a system was built by way of trial, constituted of technologies of encoding, decoding, and packaging data into an IC (integrated circuit) card. A photograph of the user's face is attached to the card, the card carries an 8KB IC memory device, and the device stores data of the photograph of the user's face etc. A password has to be inputted before any data may be taken out. A customized key is required to display the imbedded personal data and, for the restoration of the key data, the personal key known only to the owner and the company key that is kept by the card managing company need to be collated with each other. Multiple checking is available for the prevention of abuse, which include the collation of face photographs, collation with display by inputting the password, and request for the customized key to confirm the presence of authority to read the imbedded personal data. (NEDO)

  18. Achievement report for fiscal 1997 on developing a silicon manufacturing process with reduced energy consumption. Investigation and research on analyzing practical application of a technology to manufacture solar cell silicon raw materials; 1997 nendo energy shiyo gorika silicon seizo process kaihatsu. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes the achievement in fiscal 1997 of analyzing practical application of a technology to manufacture solar cell silicon raw materials. Silicon consumption for solar cells in fiscal 1997 has increased to 2000-ton level, and the supply has been very tight. For drastic improvement in the demand and supply situation, development of SOG-Si manufacturing technology and its early practical application are desired. The development of the NEDO mass-production technology using melting and refining has completed constructing the process facilities in fiscal 1998, and will enter the stage of operational research. However, insufficiency in the basic data about behavior of impurities is inhibiting the development. In the substrate manufacturing technology, discussions have shown progress on use of diversifying silicons outside the standard by using the electromagnetic casting process. For slicing and processing the substrates, development of a high-performance slicing equipment and automatic rough rinsing machine is under way. Properties required on silicon raw materials vary considerably widely because of difference in cell making systems and conditions, which is attributable to unknown impurity behavior. When 1GW production is assumed, the cell module manufacturing cost is calculated as 137 yen/W, for which low-cost mass production for its realization, slicing productivity enhancement, and cost reduction are required. The paper also describes site surveys in overseas countries. (NEDO)

  19. Report on achievements in fiscal 1999 on research and development of the industrial and scientific technology. Research and development of synergy ceramics (development of a technology to rationalize use of energies); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper summarizes the achievements in fiscal 1999 on research and development of a technology to use synergy ceramics as a material, its application technology and the common base technology. In the research of high-function active materials, development was made on catalyst and electrode materials having the selection, separation and rinsing functions, and discussions were given on materials for thermoelectric conversion of oxides. In the research and development of new thermoelectric conversion ceramics materials, searches were made on cobalt and nickel containing compound oxides. In the development of corrosion-resistant electrochemical cell materials, the honeycomb type was devised, and a technology was developed to form honeycombs laminated with different materials. In developing self-lubricating functional materials, silicon nitride with solid lubricant of MoO{sub 3} dispersed on the surface layer was developed, wherein tribological characteristics were evaluated. In developing ultra-smooth low friction materials, studies were carried out on reducing friction by controlling silicon nitride and its surface structure, placing lifter shims in an automotive engine as the application object. The joint research with the National Research Institute performed evaluations on the compound function manifestation process. (NEDO)

  20. Report on achievements in fiscal 1998. Development of silicon manufacturing process to rationalize energy usage (Development of mass production technology for solar-grade silicon); 1998 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchiyo silicon ryosanka seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the proliferation stage of solar cells, a technology is required to manufacture low-cost SOG-Si that can handle small quantity production. Development is being made on a manufacturing technology using high purity metallic silicon (99.5%) as the raw material. Considering that the subject impurities are P, B and metallic impurities (Fe, Ti and Al), a manufacturing method consisting of the following processes is being developed: metallic silicon/phosphorus removal, solidification and rough refining/boron removal, solidification and fine refining. Discussions are being advanced on phosphorus removal by using a large electron beam fusion equipment, and at the same time, the discussions are supported by fabricating and installing a large equipment intended of removing boron and the metallic impurities. Boron is removed by oxidizing it with steam. Therefore, the basic mechanism of the equipment is to spray argon plasma added with steam onto the molten silicon surface. In boron removal, diffusion of boron onto the reaction interface in the primary reaction determines the rate. A boron removal rate for B/10 to 0.1 ppm of 45 kg/h as maximum was achieved. The derived silicon has met the requirement. (NEDO)

  1. FY 1998 research result report. Ultra-high liquid crystal technology development for energy use rationalization (Technology of design/control/analysis of new functional electronic materials of the ultra-high electronic technology development promotion project); 1998 nendo kenkyu seika hokokusho. Energy shiyo gorika chosentan ekisho gijutsu kaihatsu (chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Element technology is studied to realize a reflective-type, full-color, and high-resolution liquid crystal display for super-low power consumption data display. As to the functional compound microstructure formation technology, a 4-inch panel was trially fabricated using two-layer guest-host liquid crystal technology to achieve the desired display performance by control of molecular orientation. Further, holographic PDLC elements were favorably test-fabricated. A ferroelectric PZT thin layer was formed by forming layer at low temperature at which a glass substrate can be used. Optical interference/optical dispersion type optical control materials were studied by liquid crystal/polymer composition. Also studied were super-pure/super-reliable liquid crystal compound/liquid crystal composite systems and super-anisotropic liquid crystal compound by modeling ionic impurities and liquid crystal molecular interaction. In relation to the control technology of optical reflection characteristics, effects of liquid crystal molecular structures (derivative effect and copolymer composition) on orientation were elucidated. As to the technology to form multi-dimensional anisotropic structures, efforts were made for the heightening of formation technology of simple RGB (red, green, blue) directional reflection layers using acrylate materials. The paper also outlined the comprehensive survey. (NEDO)

  2. Report on research achievements in fiscal 1999. Research and development of an ultra-high density electron SI technology (development of a technology for energy use rationalization); 1999 nendo chokomitsudo denshi SI gijutsu no kenkyu kaihatsu energy shiyo gorika gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    A high-density information network society is going to be realized in the 21st century. Information communication devices used therein are demanded of having high speed and high performance including acoustic and image digital processing, reduced size and weight, and low electric power consumption. While explosion in increase is estimated in the quantity of information handled by these information communication devices, there is a trend that the speed increase in CPU cannot follow the quantity increase. The present proposal is intended to make drastic performance enhancement by using the electron SI (comprehensive mounting) technology which includes making the LSI chips three dimensional and compounding light and electric power mounting, as well as design optimization. The present research and development has an objective to integrate the following three elements to achieve an ultra-high density electron SI technology: (1) a three-dimensional lamination technology making shortest wiring between LSI chips possible, (2) a light and electric power compounded mounting technology making high speed and large capacity transmission inside a board possible, and (3) optimal wiring structure design to suppress unnecessary electromagnetic radiation caused by increasing signal speeds. The research plan period lasts for five years. This paper reports the progresses in each theme in fiscal 1999. (NEDO)

  3. FY 1999 report on the results of the research and development project for new industry creating type industrial science and technology. Innovated casting simulation technology (Development project for commercialization of technologies related to rational use of energy); 1999 nendo kakushinteki chuzo simulation gijutsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the results of the FY1999 research and development project, implemented for development of the casting process simulation technologies, with the objectives to improve efficiency and energy-saving for the various industrial areas, e.g., industrial machines, aircraft, automobiles and vehicles, and power generation plants. For development of the mold filling and solidification process simulation programs, the efforts are directed to development of the fundamental algorithms for simulation of unidirectional solidification casting used for, e.g., turbine blades, and also to the basic works for validation of the programs. For development of the solidification structures and defect formation simulation programs, the fundamental works are done for simulation of solidification structures and channel-type segregation, which are the main problems for columnar blades, to predict the defects formed in, e.g., turbines. For development of the related measurement techniques, investigations are made for evaluation of the levitation characteristics of nickel alloys by the electromagnetically levitated droplet method and problems involved therein, prior to the tests in the the underground microgravity test center. (NEDO)

  4. FY 2000 survey report on the project for preparation of the international energy utilization rationalization basis. 2nd volume. Survey/study for the spread of energy conservation technology; 2000 nendo chosa hokokusho. Kokusai energy shiyo gorika kiban seibi jigyo (Sho energy gijutsu no fukyu no tameno chosa kenkyu to - 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In China which is the largest energy consumption country in the Asian region and has much room for the spread of energy conservation technology, investigational study was made with the aim of widely spreading energy conservation technology and solving environmental problems. This report summed up the tackling with environmental problems for making improvement in energy conservation. In the study of the CDM introduction based on the heat supply in Beijing city, conducted were the report on the research on the CDM introduction to coal-fired heat supply facilities and small gas boilers and the consideration of possibility/conditions/method of Japan's transfer of technically advanced space heating technology to China. In the study of 'advanced traffic system - Tsinghua University Green Campus Project,' carried out were the simulative study for grasp of the traffic flow in university, consideration of characteristics of exhaust gas at the time of car running on road and the road pollution mechanism, consideration of the study of electric cars considered of the environment. (NEDO)

  5. FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-performance materials technology (R and D for rationalization of energy consumption); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This report summarizes the FY 1998 research and development results of carbon-based high-performance materials technology. For (control technology of morphology and electrical conduction), a large-sized morphology controlling film-making apparatus was used, to confirm synthesis of crystalline diamond films. For research on growth of large-sized single-crystal diamond, the simulated results of the vapor-phase reactions and gas flow in a plasma were compared with the observed ones, to collect the data necessary for designing a high-speed homoepitaxial growth apparatus. For R and D of heteroepitaxial growth of thin diamond films, highly single-crystalline thin platinum films were successfully formed on a sapphire substrate. For (control technology of surface-interface and electron emission characteristics), the tests were conducted using newly introduced apparatuses, an (electron emission analysis/evaluation apparatus), (high-quality carbon-based thin film synthesizing apparatus) and (element processing/treatment apparatus). It is found that electron emission efficiency is greatly improved when the substrate with diamond particle seeds is plasma-treated under specific conditions. (NEDO)

  6. FY 2000 report on the results of the technology development of energy use reduction of machine tools. Development of dry cutting use abrasion resistant/lubricous coated tools; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Dry sessakuyo taimamo junkatsusei hifuku kogu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of energy conservation and reduction of environmental loads of machine tools, study was conducted on the dry cutting which is the cutting with no use of cutting oil, and the FY 2000 results were summed up. The study was made on dry cutting use abrasion resistance/lubricous coated tools coated with the composite membrane of which the cutting life become little lower than that of existing tools using coolant. In the survey of abrasion resistant/lubricous films, it was found out that in the adhesion to ultra-hard substrates, the DLC single-layer film consisting only of carbon indicated the same excellent adhesion as intermediate-layer inserts. As to the synthesis of abrasion resistant/lubricous films, the synthesis of the composite membrane (WC/C membrane) consisting of tungsten carbide (WC) and carbon (C) was made using arc ion plating device. The WC/C membrane is composed of W and C and has the structure in which at nm levels the layer with much W and the layer with less W were alternately piled. Study was made of devices necessary for the development of abrasion resistant/lubricous films and the film formation for drill. (NEDO)

  7. FY 2000 report on the trend survey of technical development of high speed/high function electronic devices such as quantum functional devices in association with the rationalization of energy utilization; 2000 nendo energy shiyo gorika ni kakawaru ryoshika kino soshi nado kosoku kokino denshi device no gijutsu kaihatsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Concerning the results of the R and D made by NEDO of superlattice devices (FY 1981-1990) and quantum functional devices (QFD) (FY 1991-2000) as high speed/high function electronic devices, this survey was aimed at investigating the trend of the newest technology to grasp the technical effects, the state of commercialization/product-making, and the future. The effects, technical subjects, etc. in the R and D of superlattice devices were succeeded to the R and D of QFD as the succeeding project. Here, therefore, the paper arranged the outlook of the commercialization/product-making in relation to the R and D of QFD and the future R and D subjects. In the R and D, features of QFD as target were made clear. The commercialization is limited to Motorola's QMMIC, Fujitsu's RHET, etc. As to the other R and D items, subjects of the technical development to be implemented toward the commercialization just became clear. The subject is the heightening of micro (nano meter) processing technology. The important subject, in particular, is compatibility of the heightening of micro processing and the improvement of throughput. (NEDO)

  8. Report on the achievements in fiscal 1999 on research and development of a human cooperating and coexisting type robot system (Development of energy use rationalization technology); 1999 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a system technology for the human cooperating and coexisting type robot that can perform various types of works substituting human hands. This paper summarizes the achievements in fiscal 1999. In developing a high-function hand, development and fabrication were executed on a device to teach four finger holding actions that correspond to the enhancement in action stability and control responsiveness of the four finger hand and to positions and attitudes of objects. In fabricating the robot platforms, single platform tests and remotely controlled platform connection tests were performed, which demonstrated the functions as an integrated system. In developing libraries for topography adaptive three-dimensional basic walking actions, development was carried out on libraries that correspond to menus for direct advance on a flat land, slewing, and walking on staircases and irregular land. It was found that control closer to that for actually usable robot is possible by considering time delay in articulate control when simulation was performed using the testing robot body. In the study and survey of robot proliferation, development plans were presented that take into consideration the social influence, technological factors, and cost need adaptability. (NEDO)

  9. FY 2000 report on the results of the supplementary project for the development of energy utilization rationalization technology. Leading study for the development of high efficiency thermoelectric converter; 2000 nendo energy shiyo gorika gijutsu kaihatsu hojo jigyo seika hokokusho. Kokoritsu netsuden henkan soshi kaihatsu sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    For the purpose of energy conservation and environmental protection by effective utilization of unused waste heat, the R and D of thermoelectric conversion technology were conducted, and the FY 2000 results were summed up. In the investigative study of thermoelectric converting materials, evaluation was made of the materials having a possibility of achieving the target with the element efficiency of 6% and the assumed use temperature domain of 120-330 degrees C. The result of the study indicated that the number of new materials which were made public was increasing, but there were no materials that have evidently practical applicability. In the investigative study of element manufacturing technology, trial manufacture of element was made in which the investigative results were integrated into the existing 50W element manufacturing technology, and a target of 70W was achieved. In the investigative study of the thermoelectric conversion system for industrial and commercial/residential use, field survey and questionnaire survey were conducted for three fields of iron works, chemical plant and garbage disposal plant. As a result, it was found that there was a large amount of waste heat. By the study of the system conceptional design, it was found out that the output of 40-50kW can be obtained in the system structure suitable for the source of waste heat of iron works, etc. (NEDO)

  10. Fiscal 1999 industrial science and technology R and D (industrial-academic) project report. R and D on technologies for creating bioaffinity molecules using submicron beads (Development of practical technologies for energy saving); 1999 nendo biryushi riyogata seimeitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 R and D result on technologies for creating bioaffinity molecules using submicron beads. By improving particle production, favorable SGNEGDE particles for drug fixation were produced on a scale 10 times as large as previous one. Various functional groups were obtained for particles immobilizing ligands. Magnetic purification was attempted by using new magnetic polymer particles. Synthesis of particle unsusceptible to non- specific bonds, and analysis of its modified surface properties were attempted. Reversible attachable-detachable surface coat was obtained by immobilizing boric acid to glycol group on affinity latex SG particles. The experiment result on affinity latex for detecting one-point mismatched DNAs showed the dependence of DNA hybridization on shearing resistance. To construct the library of new substances reacting with bio-receptors, solid phase synthesis of anti- tumor heterocyclic compounds was analyzed. The library of the pharmacology of new lead compound such as sugar moiety was also constructed. Study was made on attachment of alkaloid to a solid phase, synthetic reaction on a solid phase and library construction. (NEDO)

  11. Project for rationalization measures for international energy conservation. Model project concerning efficient consumption of energy for international energy conservation (Model project of waste heat recovery on billet reheating furnace); 1999 nendo kokusai energy shiyo gorika nado taisaku jigyo seika hokokusho. Kokusai energy shohi koritsuka nado model jigyo (kozai kanetsuro hainetsu kaishu model jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of curtailing energy consumption in the steel industry, a heavy energy consuming industry in Thailand, a model project was carried out for waste heat recovery on a billet reheating furnace, with the fiscal 1999 results compiled. This model project is to install a high efficiency recuperator and the latest combustion control system in the existing furnace in a SISCO (The Siam Iron and Steel Co., Ltd.) plant in Thailand. This year, following the preceding year, the construction manual was prepared, as were the test run manual, performance verification manual, operation and maintenance manual, etc. Supervisors were also dispatched to the site, giving guidance of the installation work, test run and the demonstrative operation, on the basis of these documents. Operation for verifying performance of the equipment was implemented on November 17, 1999, with the intended results obtained. Subsequently, operation maintenance instructors were dispatched, with energy saving effect proved through the collection/analysis of operation data and monitoring, for example. Further, as the dissemination activities, pamphlets and videos were prepared, and seminars were held, among others. (NEDO)

  12. Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. Surgery support system for brain tumors and other conditions (Rationalization for energy profit); 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu seika hokokusho. Noshuyo nado shujutsu shien system (energy shiyo gorika)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    In the second phase of experimental micro-manipulator fabrication, insertion parts equipped with three manipulators and operation input units are built and evaluated. The system comprises three input units and a console with a built-in controller etc., and the console is checked for shape and operability. A high resolution and high brightness stereoscopic viewer is developed for clinical use by surgical operators, and is examined for practicality. The positioning system for the intraoperative vision instrument are improved relative to its attachment method, accuracy, and sterilization tolerance. The result is evaluated, and then further improvement is made. Some functions are added to the surgical planning software program. Software programs are constructed for the real-time control and operation of the viewing system. For the micro-manipulator system to serve as a total system, the forceps are extended, tips are developed for the suction device and incision device, and their functions as members of the system are evaluated. (NEDO)

  13. Report on investigations in fiscal 2000. International infrastructure improving project for rationalization of energy use (Fundamental survey on effective utilization of unutilized biomass energy in ASEAN countries); 2000 nendo kokusai energy shiyo gorika kiban seibi jigyo chosa hokokusho. ASEAN shokoku ni okeru miriyo baiomasu energy no yuko riyo ni kansuru kisochosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective to utilize 'biomass' being the unutilized and reproducible energy source, which exists affluently in the ASEAN countries, investigations and discussions have been carried out on electric power generation using palm shells as fuel in Malaysia. This paper reports the achievement in fiscal 2000. The biomass energy plant project was discussed with the followings as the conditions: an output of 1 MW, use of biomass in the form of wastes discharged from oil palm mills, the system of direct combustion process with boiler/steam turbine generation process, and power transmission to public grids. As a result of the discussions, the following conclusions were obtained: reduction of greenhouse effect gas exhaust will amount to 81,540 t-CO2/year, reduction will be realized on white smoke pollution caused by wastes incineration being criticized from various sectors and such harmful gas exhaust as SOx and NOx discharged from fossil fuel power generation, the uncertainty of electric power supply currently depending on DG power generation will be mitigated resulting in acquisition of economic effects, and electric power supply to 1,000 households will be possible, contributing to enhancement of living standard due to electrification. (NEDO)

  14. Fiscal 2000 international energy use rationalization measures project. International energy consumption efficiency improvement technology diffusion project - Green helmet project (Thailand: Report on heating furnace energy conservation seminar); 2000 nendo. Kokusai energy shiyo gorika to taisaku jigyo, Kokusai energy shohi koritsuka to gijutsu fukyu jigyo, Green helmet jigyo (Thai : kanetsuro shoenergy seminar hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The above-named seminar was held in Bangkok, Thailand, on January 30, 2001, and covered three kinds of industries of ceramics, glass, and aluminum. Approximately 200 people attended the meeting, consisting of NEDO (New Energy and Industrial Technology Development Organization)-affiliated people and 16 lecturers from Japan, and Thai participants. The seminar comprised a 'keynote address' and 'lectures on engineering' that aimed at the three industries as a whole, and 'lectures on engineering' and 'cases and activities for energy conservation' that aimed, respectively, at the three industries. Lectures were delivered on operating technologies which were already in practical use and on state-of-the-art technologies. The keynote address, entitled 'Global warming prevention and industrial furnaces,' covered the results of the 'High-performance industrial furnace field test project.' The lectures on engineering dealt with the 'instrumentation control system' and 'heat insulation technology' which were basic technologies for energy conservation and 'diagnosis technology and practice' which aimed at the enhancement of energy conservation after the start of operation. Questions and answers were earnestly exchanged. (NEDO)

  15. Achievement Report for fiscal 1997 on developing a silicon manufacturing process with reduced energy consumption. Development of technology to manufacture high quality solar cell silicon substrates; 1997 nendo energy shiyo gorika silicon seizo process kaihatsu. Kohinshitsu taiyo denchiyo silicon kiban seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is intended to establish an energy saving type mass production technology to manufacture solar cell substrates by using the electromagnetic casting process. This paper describes the achievements in fiscal 1997. Preliminary experiments were performed for high-performance slicing processing and post-slicing rinsing to reduce the cost by enhancing productivity in the slicing process. Since there is a problem of mixing of contaminating raw materials due to diversification in raw materials, resistance and impurity concentration must be determined on each raw material as the materials for the Czochralski method. Then, the raw materials are sorted out referring to the determination results, and they can be used for the electromagnetic casting process upon optimizing them. As a result of having sliced an ingot of 15-cm square with a length of 40 cm by using a mass-production wire saw, an accuracy of 22.8 {mu}m was attained as intra-face variance when the required cutting time was 476 minutes and the substrate thickness is 348 {mu}, thus having obtained prospect for achieving the standard. Development was made on a water jetting rough cleaning machine to separate and remove slurries (oil and grinding particles) from the substrates after slicing, and an arm robot to accommodate substrates into cassettes, which provided processing velocity of 9 second per substrate. A problem of raising the speed remains to be solved. (NEDO)

  16. Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (development of rational energy use technology); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size particles from a fine-grain high-density matrix through an improved particle formation process. Its toughness was considerably improved by controlling grain shape and grain boundary structure. A precipitation mechanism was also discussed. 89 refs., 107 figs., 14 tabs.

  17. Achievement report for fiscal 1998. Research and development of technologies for creating new bioaffinity molecules using submicron beads (Energy use rationalization related technology practicalization); 1998 nendo biryushi riyogata seitai ketsugo busshitsunado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the effort to develop chemical substance/bioreceptor analysis technology using submicron beads, polystyrene core/polyglycidyl methacrilate beads are used in a study started about a detachable spacer using newly developed fixation technology. In the development of bioaffinity chemical substance refining technology, two kinds of sugars and several kinds of aromatic aldehydes serve as building blocks in the construction of a library, and studies are made of analyses using liquid chromatography and mass spectrography. In the development of novel substance creation technology based on information on the analysis of chemical substance/bioreceptor, in an effort at developing technologies for creating novel function provided chemical substances, heterocyclic compounds, alkaloids, and sugar compounds are selected and their syntheses in the liquid phase and solid phase are studied, which is again for the construction of a library. (NEDO)

  18. Technology for semi-endless use of lubricating oil, no waste oil, improvement of reliability and keeping high thermal efficiency in engines; Jinzo kino seijo gijutsu ni yoru engine oil no han`eikyu shiyo to haiyu zero, oyobi shinraisei kojo to netsukoritsu teika no boshi (joyosha ni yoru shiken oyobi truck ni okeru jitsuyoka)

    Energy Technology Data Exchange (ETDEWEB)

    Azuma, T [Teikyo University, Tokyo (Japan); Sumimoto, M; Kimura, I

    1997-10-01

    The authors have developed a new technology which enables it to use lubricating oil almost forever without any waste oil, only compensating lost oil and additives. The system has been working well in many marine and co-generation diesel engines. These engines have been also free from most of engine troubles. This paper reports the test results made on a car and some trucks. Besides above mentioned advantages, the results show that high thermal efficiency has been kept for more than ten years in the car tested and that the exhaust gas brake is much improved in the trucks. 8 refs., 4 figs.

  19. Achievement report for fiscal 1999 on research and development of technologies for medical welfare equipment. High-speed and three-dimensional X-ray CT system using a cone beam X-ray; 1999 nendo iryo fukushi kiki kenkyu kaihatsu seika hokokusho. Kosoku kon beam sanjigen x sen CT (energy shiyo gorika)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development is conducted of (1) a three dimensional data reconstruction system and (2) a three-dimensional image processing system. Under item (1), an experimental 3-dimensional image reconstruction unit is built. Its arithmetic performance is evaluated, and it is found that it will complete a 512{sup 3}-voxel reconstruction process in 5 minutes. An experimenting system which is a one-piece unit is built for evaluating apparatuses. Under item (2), a viewer is fabricated as an element basic to 3-dimensional image processing, which is to display 3-dimensional data in a 2-dimensional image. In addition, basic 3-dimensional image processing is enabled by adding to the viewer an image filter and a function of describing the cross section at an arbitrarily chosen angle. In the development of a total system, (1) a basic design is prepared for a data collecting device IC, (2) a sampling grate is designed, (3) basic designs are prepared for the gantry and the bed, and (4) an image quality assessment system is constructed. Under item (1), specifications are determined for the data collecting device IC, and a test piece is built. Under item (2), it is confirmed that the experimental data transmitter is capable of 622Mbps. Under item (3), preparation of a detailed design is stared. Under item (4), a simulation is conducted for the formation of a human body equivalent-phantom. (NEDO)

  20. Fiscal 1998 R and D report on the human coordination/coexistence robot system (development of practical technology for rational energy use); 1998 nendo ningen kyocho kyozongata robot system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report reports the R and D on the human coordination/coexistence robot system possible to perform various works instead of people. As for an intelligent robot hand, 4-finger hand and arm hardware were developed and fabricated, and operation of the assembled system of them was tested. As for a robot platform, a remote control platform, and the interface specifications of command communication and data communication were studied. As for 3-D walk adaptive to land shapes, an analysis environment for a control algorithm and an easy-to-use environment for a virtual platform simulator were prepared. By using this analysis environment, the central part of the walk control algorithm, and a module for forming walk patterns were developed. In the application research on energy saving, various problems on dangerous and harsh conditions in construction and disaster restoration works were analyzed, and the needs of a humanoid robot for such works were studied. (NEDO)

  1. Report on achievements in fiscal 1996. International energy usage rationalization project (project to survey energy consumption efficiency improvement analyzing tools for Asia/data edition); 1996 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho shiryohen. Asia energy shohi koritsuka bunseki tool chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    This paper is a collection of data on surveys for energy consumption efficiency improvement, taking Japan, Korea, Indonesia, Thailand, and Philippines as the object countries. I. Industry related various value tables consist of the following: basic transaction table, throw-in coefficient table, final demand converter table, import coefficient table, added value coefficient table, inverse matrix coefficient table, sensitivity coefficient table, influence coefficient table, production inducing amount, production induction dependence, import inducing amount, import induction coefficient, import induction dependence, and inverse matrix coefficient table. II. Energy related various coefficient tables consist of the following: inherent unit quantity table, energy consumption table, CO2 table (1), CO2 table (2), unit requirement table, energy consumption induction table, energy consumption induction coefficient table, energy consumption induction dependence table, CO2 induction table (1), CO2 induction coefficient table (1), CO2 induction dependence table (1), CO2 induction table (2), CO2 induction coefficient table (2), and CO2 induction dependence table (2). Industries are classified into 34 kinds. III. The energy consumption table, CO2 table (1) and CO2 table (2) are shown as the simulation results for the four countries: Korea, Indonesia, Thailand, and Philippines. (NEDO)

  2. Technological development of machine tools using less energy in fiscal 2000. Achievement report on research and development of cutting process replacing electric discharge processing; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Hoden kako wo chikansuru sessaku kakoho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made with an objective to replace the electric discharge processing consuming a large amount of energy and having environmental load, with the cutting process consuming less energy while maintaining the equivalent processing precision. This paper summarizes the achievements in fiscal 2000. Development of cutting tools has made three times or more as many multi-aspect utilization as compared to conventional tools possible by researching the tip shapes. In addition, ultra hard end mill suitable for cutting very hard materials using an ultrasonic cutting head was fabricated on the trial basis, and its cutting capability was verified. In developing the cutting processing heard, a vibration mode possible of cutting with the ultra hard tool was generated, ATC has become possible, and the possibility of cutting hard-to-cut materials was verified. For processing a narrow and deep part, an improved type tool was developed, whereas the practical cutting performance suppressing wear of the blade tip was obtained. To deal with the environment, development and prototype fabrication were performed on a unit having a grease lubricated high-speed main shaft that is considered to be the mainstream in the future. In the operation test at 20,000 min-L, know-how was acquired in relation with the basic performance, manufacture and use of the unit. (NEDO)

  3. Research report for fiscal 1998. Basic research for promoting joint implementation of energy use rationalization in Chinese steel industry (examination of introduction of scrap preheating system for electric furnaces); 1998 nendo chosa hokokusho. Chugoku tekkogyo ni okeru energy no shiyo gorika (denkiro scrap yonetsu system donyu kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Investigations are conducted on a project of introducing a scrap preheating system based on the central insertion movable shaft design into China's electric furnaces for the sake of energy saving and global warming gas reduction. Of the electric furnaces numbering approximately 3400 now in operation in China, most are small and antiquated, and are extremely low in energy efficiency when in operation. The percentage of electricity supplied by coal-fired facilities is high, and this causes the CO2 reduction problem. Investigations are conducted into four steel mills operating electric furnaces, and examinations are made on the applicability of a preheating system, which is the ultimate batch system developed by Nippon Steel Corporation. Studies are conducted for Wuyang Iron and Steel Co., Ltd., Tianjin Steel Pipe Co., Ltd., Budong Iron and Steel Co., Ltd., and Shanghai Five Steel Co., Ltd., and it is found that greenhouse gas will be reduced by 31,000 tons, 21,000 tons, 13,000 tons, and 11,000-tons at the said mills, respectively. It is learned that the cost to be invested will be retrieved in approximately 2.5 years, 2.8 years, 7.7 years, and 8.0 years, respectively. It is concluded that Shanghai Budong Iron and Steel (Group) Co., Ltd., is the best candidate to be equipped with the above-said system. (NEDO)

  4. Achievement report for fiscal 1999 on the development of silicon manufacturing process rationalizing energy utilization. Research and study on analysis to put silicon raw material manufacturing technology for solar cells into practical use; 1999 nendo energy shiyo gorika silicon seizo process kaihatsu seika hokokusho. Taiyo denchi silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In order to support the development and practical application of a mass production technology for manufacturing silicon raw materials for solar cells, research and study were performed on trends of developing the related technologies, and movements in markets and industries. This paper reports the achievements thereof in fiscal 1999. Markets for solar cells are growing favorably, and the worldwide solar cell production in 1999 was 200 MWp, of which 80% or more is occupied by crystalline silicon solar cell. While development of the manufacturing technology for SOG-Si mass-production is in the stage of operation research of pilot plants, it has been verified that problems of impurity contamination was resolved, and high-purity silicon can be manufactured. In developing the silicon scrap utilization technology and a technology to integrate silicon refinement with casting, a conversion efficiency of 14% or higher was acquired in prototype sample substrates. It has been verified that a variety of raw materials can be dealt with by using the above technology, which has a possibility of cost reduction. In developing a substrate manufacturing technology, a great progress has been made in enhancing the productivity and reducing the cost by developing the continuous casting in the electromagnetic casting and the automation technology. (NEDO)

  5. FY 2000 report on the results of the technology development of energy use reduced machine tools, etc. R and D of the environment-friendly grinding machine system; 2000 nendo energy shiyo gorika kosaku kiki nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were conducted of a grinding machine system of an environmental-friendly type in which no coolant is used or the amount of coolant is reduced, and the FY 2000 results were summed up. As to the ECOLOG grinding newly thought up, the roles were divided: the lubrication into a trace of the vegetable oil supplied onto the grindstone surface, cooling into a trace of the cooling water supplied to the structure, discharge of chips to the cooling water for bed table cleaning. By this, the amount of the cooling water becomes approximately 1/3 of that in the conventional grinding. Concerning the ECOLOG grinding using the usual grindstone, the grinding performance equal to that in the conventional grinding was confirmed. In the study for making the cooling water non-pollutant, the chlorine/sulfur free coolant was developed which includes no chemical substances designated by the PRTR law at all. It was confirmed that the grinding performance was almost the same level as the existing coolant which includes sulfur. In the study of the supply of coolant applied with ultrasonic waves, the result was obtained that in the optical glass grinding, the number of scratches decreased and the surface roughness improved even at the flow rate of coolant which is less than in the conventional grinding. (NEDO)

  6. Research and development in fiscal 1999 of university collaboration type industrial and scientific technologies. Research and development of the next generation ferroelectric memory(Development of energy use rationalization technology); 1999 nendo jisedai kyoyudentai memory no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research has been performed with an objective to develop a new circuit configuration that separates data read-out function from memory storage function. This paper summarizes the achievements in fiscal 1999. In developing a circuit simulation technology, the existing macro model was used to derive circuit response in a partially polarized condition. Comparing the hysteresis shape with an experiment revealed that the partially polarized condition can be expressed well. Incorporation into SPICE will be discussed in the future. In the research of optimizing the circuit configuration, an SrTa{sub 2}O{sub 6}/SiON buffer layer was used to have fabricated a ferroelectric gate FET being the constituting element of the memory cell. The function separation type 1T2C memory was discussed on aggregation, manufacturing processes, and optimal cell arrangement, and was concluded as a superior memory. It was disclosed that the high performance ferroelectric gate FET needs to take the FEMIS structure, and make the area of a ferroelectric capacitor smaller than the area of a buffer layer capacitor. (NEDO)

  7. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

  8. Fiscal 2000 report on results of project for R and D of industrial science and technology in cooperation with universities, and R and D of platform for designing high functional materials (development of energy use rationalization technology); 2000 nendo kokino zairyo sekkei platform no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    R and D was conducted concerning sophistication and high speeding in designing materials by simulation technology utilizing a new calculation method, with fiscal 2000 results compiled. A group working on coarse-grained molecular dynamics have tackled three problems such as the development and application of a multi-purpose coarse-grained molecular dynamics engine called COGNAC. A group on dynamic average domain method added various functions to a new multi-purpose dynamic average domain simulator called SUSI, and also achieved a variety of results by simulations using this simulator. A group on dispersed structure simulation has been proceeding with the development and application study of a multi-phase dynamics simulator called MUFFIN. A verification research group carried out verification of predictability, with the accuracy intended by each program, on thermal properties, optical properties, formability, etc., using polyethylene as the verification material. A platform group prepared a new high-speed platform that used less memory. (NEDO)

  9. Impact of war on child health in northern Syria: the experience of Médecins Sans Frontières.

    Science.gov (United States)

    Meiqari, Lana; Hoetjes, Maartje; Baxter, Louisa; Lenglet, Annick

    2018-03-01

    Few data are available to evaluate the impact of Syrian war on civilian population; to describe this impact on child health, this article uses data from Médecins Sans Frontières-Operational Centre Amsterdam's activities in Tal-Abyad and Kobane cities, northern Syria (2013-2016). Data were obtained from routine medical datasets and narrative reports, for out-patient clinics, immunisation, nutritional monitoring and assessments, and in-patient care, and were analysed quantitatively and qualitatively. Infections were the largest contributor to morbidity. The proportion of war on the health of children; • Médecins Sans Frontières (MSF-OCA) has worked in northern Syria during different times since 2013. What is New • Quantitative and qualitative analysis of MSF's routine medical data and situtation reports show that one fifth of all consultations in children war, e.g. thalassemia.

  10. FY 2000 report on the survey project on the policy for international energy utilization rationalization, etc. - model project on the heightening of international energy consumption efficiency. Viability survey of the project on energy conservation in the urea synthesis process in India; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo - kokusai energy shohi koritsuka nado model jigyo chosa hokokusho. Indo ni okeru nyoso gosei process sho energy jigyo jisshi kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of conserving energy and reducing greenhouse effect gas, a remodeling project was studied of urea plants constructed from the 1960s to the 1970s. Conditions for being companies for study are as follows: company has a production scale of more than 0.2 million t/y, adopts the complete circulation method, and will continue operation. And, Duncans Industries Ltd. (DIL) was selected. DIL owns the ammonia plant of 3 series x 400 t/d and the urea plant of 3 series x 682 t/d. In the modeling, stripper and carbamate condenser are added to the existing reactor as the main equipment. As a result of the study, the energy conservation effect was 13,667 toe/y, and the amount of reduction in greenhouse effect gas was 42,289 t-CO2/y. The total amount of this project was roughly estimated at 1.517 billion yen. By carrying out the project, the urea production cost is reduced approximately $9/t, but the project becomes unprofitable if the urea price is based on $188.1/t. (NEDO)

  11. Fiscal 1998 research report (continued from the fiscal 1997 project). International survey project for rational energy use / Basic survey on efficient energy use in developing countries (Database construction project) / Survey on Japanese energy conservation technologies; 1998 nendo (1997 nendo jigyo kurikoshi) kokusai energy shiyo gorika nado chosa jigyo hatten tojokoku energy shohi koritsuka kiso chosa (database kochiku jigyo) chosa hokokusho. Nippon no sho energy gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    As a part of development of the energy conservation technology database, revision was made on 'Directory of Energy Conservation Technology in Japan' which was published to present the energy conservation technology of the Japanese energy-intensive industry to Asian countries in fiscal 1996. The previous directory was composed of 307 technical items, and 126 items among them were deleted and new 63 items were added through this revision. The technologies with energy conservation effects more than 10% were mainly selected by knowledge of the industrial members of the committee and other specialists. The energy conservation effect widely ranges from low-level one to high-level one, and the number of all the energy conservation technologies is enormous. Consequently, it should be considered that the applicable extent of the energy conservation technologies is dependent on the energy cost or economical situation of Japan and developing countries. (NEDO)

  12. Fiscal 1998 joint R and D project on industrial science and technology with university. Research report on the production process of semiconductor devices by Cat-CVD (Development of practical technology for rational use of energy); 1998 nendo daigaku renkei sangyo kagaku gijutsu kenkyu kaihatsu project. Cat-CVD ho ni yoru handotai device seizo process seika hokokusho (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The Cat-CVD method is in verification test to establish it as production process of various semiconductor devices such as Ga-As IC, ferroelectric IC, Si IC, and TFT. This paper outlines the research results in fiscal 1998. Study was made on concept design of the Cat-CVD equipment for formation of Ga-As protective film, and basic technology for formation of SiN{sub x} film. Although reducing gas is used for deposition of SiN{sub x} film, anxious modification of oxide ferroelectric materials was avoided by substrate temperature control. Design and fabrication of the CVD equipment for Si ICs were also studied. The equipment was made of Al to control degassing as low as possible. As for production of TFT for LCD, formation technology of high-quality insulating thin film for low-temperature poly-Si TFT by CVD method, and formation of advanced insulating thin film and advanced poly- Si thin film were studied. A large-size deposition method of TFT insulating film, and low-temperature formation technology of poly-Si were also studied. (NEDO)

  13. Fiscal 1997 report on the development of an energy use rationalization ultra-high tech liquid crystal technology. Project of development/promotion of ultra-high tech electronic technology / technology of design/control/analysis of new functional electronic materials; 1997 nendo kenkyu seika hokokusho energy shiyo gorika chosentan ekisho gijutsu kaihatsu. Chosentan denshi gijutsu kaihatsu sokushin jigyo / shinkino denshi zairyo sekkei seigyo bunseki gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    A research was conducted with the aim of developing an ultra-low power consuming type information display which supports the next next generation informatizing society. As to the function combined type fine structure formation technology, a formation technology of fine structure supporting multi-layer pixel by organic polymer materials was established to confirm a possibility of adopting it to high functional liquid crystal display. Concerning the high functional fine structure formation technology, a study was proceeded with on holographic PDLC which is an interference reflection coloring method. In relation to the low temperature film formation technology of ferroelectric thin films, a film formation device was introduced to obtain basic data, and at the same time a possibility was studied of improving film characteristics by laser annealing conducted after the film formation. Moreover, concerning the new functional material technology, studies were made of optical interference/high light-scattering control materials, light alignment elements, ultra-high purity/ultra-reliable optical materials, ultra-anisotropy optical materials, etc. About the light reflection characteristics control technology, studied were new liquid crystal molucular orientaion control technology, multi-dimensional anisotropy structure formation technology, etc. 100 refs., 273 figs., 58 tabs.

  14. FY 2000 report on the results of the technology development of energy use reduction of machine tools, etc. Technology development of environmental load reduction related to water soluble lubricating oil, etc. (R and D of low energy coolant degradation prevention technology and waste liquid processing technology); 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Suiyosei junkatsuyu ni kakawaru kankyo fuka teigen nado gijutsu kanri (tei energy coolant fuhai boshi gijutsu oyobi haieki shori gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were carried out on a system by which the long life of coolant of machine tools can be achieved and a system to process waste efficiently, economically and with less environmental loads, and the FY 2000 results were summed up. In the R and D of a system to prevent degradation of low energy coolant, measurement was made of effects of the degradation prevention system at a laboratory level, and it was found out that propagation of bacteria causing the degradation can be prevented with pH kept high. Further, it was admitted that the alkali effect on metal formability was not very much. As to the coolant processing, in the present situation, most of the coolant is taken back by industrial waste processing dealers. So, the development of the low energy waste liquid processing system is earnestly desired. In the R and D of the low energy waste liquid processing system, test on characteristics evaluation was conducted about each method of systems. Subjects to be improved/solved were extracted such as the point that volatile organic matters are included in condensed water after evaporation of waste liquid and there seems to be a possibility of needing the secondary processing. (NEDO)

  15. FY 1999 Report on the results of technological development of machine tools for rationalization of energy utilization. Development of a lathe with high precision and conservation of energy using natural phenomenon (Thermal countermeasure using self compulsory cooling and thermal insensitive structure - results of the first year); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Shizen gensho wo takumi ni oyoshita sho energy koseido senban no kaihatsu (self kyosei reikyaku to netsufukan gijutsu wo mochiita netsuhenkei yokusei taisaku - dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A lathe, which is a central tool in a factory of automobiles or home electric appliances, tends to suffer decreased machining precision resulting from thermal deformation. This project is aimed at development of the energy-saving, high-precision lathe technologies using self compulsory cooling and thermal insensitive technologies as the countermeasures against the thermal deformation. The self compulsory cooling is a method of cooling by evaporation of water with an evaporative, water-absorptive cloth being bonded to a machine tool surface around the major axis. The thermal insensitive technologies include the three-dimensionally zero-center design technologies which help design a lathe in such a way to set the processing point (tool working point) at the base of thermal deformation in the X, Y and Z axis directions; material combination technologies to control thermal deformation; and coloring technologies to control thermal deformation. The development target is the high-precision lathe fabrication technologies, which realize a temporal precision change of 1 to 2 {mu}m or less per work dimension of 100mm. The activities cover 5 areas, including development of elementary technologies for each item and construction/evaluation of the full-size test unit. (NEDO)